WorldWideScience

Sample records for earth chloride solutions

  1. Hydrochloric acid recovery from rare earth chloride solutions by vacuum membrane distillation

    Institute of Scientific and Technical Information of China (English)

    TANG Jianjun; ZHOU Kanggen

    2006-01-01

    The possibility of the recovery of hydrochloric acid from rare earth (RE) chloride solutions was first experimentally studied by batch vacuum membrane distillation (VMD). The recovery by continuous VMD was also studied to devise methods that enabled the operation of VMD setup in a stable condition as well as to increase the membrane-operating life The results indicated that HCl separation with RE by VMD was possible, and the recovery ratio of 80% could be achieved by batch VMD. In continuous VMD, when the temperature of circular solutions, circular rate, and downstream pressure was62-63℃, 5.4 cm/s, and 9.33 kPa, respectively, the HCl concentration in circular solutions and the processing capacity per membrane area were obtained. The mathematical results were in accordance with the experimental ones.

  2. Ce1-xLaxOy solid solution prepared from mixed rare earth chloride for soot oxidation

    Institute of Scientific and Technical Information of China (English)

    韩雪; 王亚飞; 郝红蕊; 郭荣贵; 胡运生; 蒋文全

    2016-01-01

    Ce1–xLaxOy solid solution was simply prepared using mixed rare earth chloride (RECl3·xH2O, RE=Ce, La>99%, containing unseparated Ce and La from rare earth metallurgical industry) as precursor by ultrasonic-assisted co-precipitation method with differ-ent ultrasonic frequencies (CLf,f=200, 400, 600, 800, 1000 Hz). A compared Ce1–xLaxOy solid solution (CL*) was also prepared by the same mothod with 10% less precipitant. X-ray diffraction results confirmed the formation of Ce1–xLaxOy solid solution, and the crystal structures of these catalysts were not very sensitive to ultrasonic frequency and precipitant amount. However, both of the fac-tors had obvious effect on morphology and surface area of CL, and precipitant amount seem to play a more crucial role than ultra-sonic frequency for Ce1–xLaxOy solid solution preparation. When soot and catalyst were tight contacted, the peak temperature (Tpeak) of soot oxidation and oxygen reducing temperature for CLf catalysts decreased linearly with increasing surface area. Under loose contact condition, theTpeak had obvious negative correlation with H2 consumption. It was inferred that good reducibility of the Ce1–xLaxOy solid solution favored the soot oxidation reaction. The Ce1–xLaxOy solid solution prepared from unseparated rare earth chloride showed a good soot oxidaiton activity. Controlling the preparation conditions to prepare a CL catalyst would high surface area will enhance its reducibility and activity.

  3. Thermodynamic properties of potassium chloride aqueous solutions

    Science.gov (United States)

    Zezin, Denis; Driesner, Thomas

    2017-04-01

    Potassium chloride is a ubiquitous salt in natural fluids, being the second most abundant dissolved salt in many geological aqueous solutions after sodium chloride. It is a simple solute and strong electrolyte easily dissociating in water, however the thermodynamic properties of KCl aqueous solutions were never correlated with sufficient accuracy for a wide range of physicochemical conditions. In this communication we propose a set of parameters for a Pitzer-type model which allows calculation of all necessary thermodynamic properties of KCl solution, namely excess Gibbs free energy and derived activity coefficient, apparent molar enthalpy, heat capacity and volume, as well as osmotic coefficient and activity of water in solutions. The system KCl-water is one of the best studied aqueous systems containing electrolytes. Although extensive experimental data were collected for thermodynamic properties of these solutions over the years, the accurate volumetric data became available only recently, thus making possible a complete thermodynamic formulation including a pressure dependence of excess Gibbs free energy and derived properties of the KCl-water liquids. Our proposed model is intended for calculation of major thermodynamic properties of KCl aqueous solutions at temperatures ranging from freezing point of a solution to 623 K, pressures ranging from saturated water vapor up to 150 MPa, and concentrations up to the salt saturation. This parameterized model will be further implemented in geochemical software packages and can facilitate the calculation of aqueous equilibrium for reactive transport codes.

  4. Viscosity and density tables of sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Fair, J.A.; Ozbek, H. (comps.)

    1977-04-01

    A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

  5. Hydrolysis of ferric chloride in solution

    Energy Technology Data Exchange (ETDEWEB)

    Lussiez, G.; Beckstead, L.

    1996-11-01

    The Detox{trademark} process uses concentrated ferric chloride and small amounts of catalysts to oxidize organic compounds. It is under consideration for oxidizing transuranic organic wastes. Although the solution is reused extensively, at some point it will reach the acceptable limit of radioactivity or maximum solubility of the radioisotopes. This solution could be cemented, but the volume would be increased substantially because of the poor compatibility of chlorides and cement. A process has been developed that recovers the chloride ions as HCl and either minimizes the volume of radioactive waste or permits recycling of the radioactive chlorides. The process involves a two-step hydrolysis at atmospheric pressure, or preferably under a slight vacuum, and relatively low temperature, about 200{degrees}C. During the first step of the process, hydrolysis occurs according to the reaction below: FeCl{sub 3 liquid} + H{sub 2}O {r_arrow} FeOCl{sub solid} + 2 HCl{sub gas} During the second step, the hot, solid, iron oxychloride is sprayed with water or placed in contact with steam, and hydrolysis proceeds to the iron oxide according to the following reaction: 2 FeOCl{sub solid} + H{sub 2}O {r_arrow} Fe{sub 2}O{sub 3 solid} + 2 HCl{sub gas}. The iron oxide, which contains radioisotopes, can then be disposed of by cementation or encapsulation. Alternately, these chlorides can be washed off of the solids and can then either be recycled or disposed of in some other way.

  6. Green process to recover magnesium chloride from residue solution of potassium chloride production plant

    Institute of Scientific and Technical Information of China (English)

    Lin WANG; Yunliang HE; Yanfei WANG; Ying BAO; Jingkang WANG

    2008-01-01

    The green process to recover magnesium chlor-ide from the residue solution of a potassium chloride pro-duction plant, which comes from the leach solution of a potash mine in Laos, is designed and optimized. The res-idue solution contains magnesium chloride above 25 wt-%, potassium chloride and sodium chloride together below 5 wt-% and a few other ions such as Br-, SO2-4and Ca2+. The recovery process contains two steps: the previous impurity removal operation and the two-stage evapora-tion-cooling crystallization procedure to produce magnes-ium chloride. The crystallized impurity carnallite obtained from the first step is recycled to the potassium chloride plant to recover the potassium salt. The developed process is a zero discharge one and thus fulfills the requirements for green chemical industrial production. The produced magnesium chloride is up to industrial criteria.

  7. Hydrolysis of cupric chloride in aqueous ammoniacal ammonium chloride solutions

    Directory of Open Access Journals (Sweden)

    Limpo, J. L.

    1995-06-01

    Full Text Available Cupric solubility in the CuCl2-NH4Cl-NH3-H2O system for chloride concentrations lower than 4 molal in the temperature range 25-60 °C was studied. The experimental results show that for chloride concentration between 3.0 and 1.0 molal the cupric solubility is determined by the solubility of the cupric hydroxychloride Cu(OH1.5Cl0.5. For a chloride concentration value of 4.0 molal, there are two cupric compounds, the hydroxychloride Cu(OH1.5Cl0.5 or the diammine chloride Cu(NH32Cl2, on which the solubility of Cu(II depends, according to the temperature and the value of the ratio [NH3]Total/[Cu]Total.

    Se estudia la solubilidad del Cu(II en el sistema CuCl2-NH4Cl-NH3-H2O para concentraciones de cloruro inferiores a 4 molal en el intervalo de temperaturas 25-60 °C. Los resultados experimentales muestran que, para concentraciones de cloruros comprendidas entre 3,0 y 1,0 molal, la solubilidad cúprica viene determinada por la solubilidad del hidroxicloruro cúprico, Cu(OH1.5Cl0.5. Para concentraciones de cloruro 4,0 molal, existen dos compuestos cúpricos, el hidroxicloruro, Cu(OH1.5Cl0.5 o el cloruro de diamina, Cu(NH32Cl2, de los que, de acuerdo con la temperatura y con el valor de la relación [NH3]Total/[Cu]Total depende la solubilidad del Cu(II.

  8. The ionic product of water in concentrated tetramethylammonium chloride solutions.

    Science.gov (United States)

    Sipos, P; Bódi, I; May, P M; Hefter, G T

    1997-04-01

    The ionic product of water, pK(w) = - log[H(+)][OH(-)] has been determined in aqueous solutions of tetramethylammonium chloride over the concentration range of 0.1-5.5 M at 25 degrees C using high-precision glass electrode potentiometric titrations. pK(w) data relating to aqueous potassium and sodium chlorides at ionic strengths up to 5 M are markedly lower than the tetramethylammonium chloride results. These differences are almost certainly due to weak associations between potassium and (especially) sodium and hydroxide ions.

  9. Hafnium extraction from acidic chloride solutions by Cyanex 923

    Energy Technology Data Exchange (ETDEWEB)

    El-Ammouri, E.; Distin, P.A. [McGill Univ., Montreal (Canada)

    1996-08-01

    Hafnium extraction from hydrochloric acid/lithium chloride solutions into Cyanex 923 in kerosene has been studied. Variables investigated were hydrochloric acid, total chloride and hafnium concentrations in the aqueous phase, and extractant/modifier (isodecanol) levels in the organic phase. Hafnium is considered to load as the tetrachloride complex forming a disolvate with Cyanex 923. Results are compared with equivalent data for zirconium extraction. 14 refs., 7 figs., 2 tabs.

  10. An experiment on multibubble sonoluminescence spectra in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    CHEN Zhan; XU JunFeng; HUANG Wei; CHEN WeiZhong; MIAO GuoQing

    2008-01-01

    We investigated experimentally the spectra of MBSL in sodium chloride water solution with krypton as dissolved gas. We observed and compared the spectra of hydroxyl ion at 310 nm and that of sodium atom at 589 nm. It has been found that under the same experimental condition, the intensity of sodium atom spectra is obviously higher than that of the hydroxyl ion spectra, and is more sensitive to the experimental condition. The krypton content, the concentration of sodium chloride solution, and the driving sound pressure obviously affect the spectra intensity in certain range.

  11. Platinum uptake from chloride solutions using biosorbents

    Directory of Open Access Journals (Sweden)

    Mehmet Hakan Morcali

    2013-04-01

    Full Text Available Present work investigates platinum uptake from synthetically prepared, dilute platinum-bearing solutions using biomass residues, i.e. pistachio nut shell and rice husk, which are abundant in Turkey, and provides a comparison between these two biosorbents. Effects of the different uptake parameters, sorbent dosage, contact time, temperature and pH of solution on platinum uptake (% were studied in detail on a batch sorption. Before the pistachio nut shell was activated, platinum uptake (% was poor compared to the rice husk. However, after the pistachio nut shell was activated at 1000 °C under an argon atmosphere, the platinum uptake (% increased two-fold. The pistachio nut shell (original and activated and rice husk were shown to be better than commercially available activated carbon in terms of adsorption capacity. These two sorbents have also been characterized by FTIR and SEM. Adsorption equilibrium data best complied with the Langmuir isotherm model. Maximum adsorption capacities, Qmax, at 25 °C were found to be 38.31 and 42.02 mg.g- 1for the activated pistachio nut shell and rice husk, respectively. Thermodynamic calculations using the measured ∆H°, ∆S° and ∆G° values indicate that the uptake process was spontaneous and endothermic. The experimental data were shown to be fit the pseudo-second-order kinetic model.

  12. Synthesis of brookite-typed titania from titanium chloride solution

    Institute of Scientific and Technical Information of China (English)

    Satoshi OKANO; Saeki YAMAMURO; Toshiro TANAKA

    2009-01-01

    The brookite-phase TiO2 was prepared by a hydrothermal synthesis of titanium chloride solution. The thermolysis time and the pH value of the solution were controlled during the synthesis. X-ray diffraction experiments showed that TiO2 powders partially containing the brookite-phase were successfully ob-tained. A great amount of OH in the reaction solution was found to be important to obtain the brookite phase because the intermediate complex leading to the brookite phase consumes more OH- than other phases like the rutile.

  13. Synthesis of brookite-typed titania from titanium chloride solution

    Institute of Scientific and Technical Information of China (English)

    Satoshi; OKANO; Saeki; YAMAMURO; Toshiro; TANAKA

    2009-01-01

    The brookite-phase TiO2 was prepared by a hydrothermal synthesis of titanium chloride solution. The thermolysis time and the pH value of the solution were controlled during the synthesis. X-ray diffraction experiments showed that TiO2 powders partially containing the brookite-phase were successfully obtained. A great amount of OH-in the reaction solution was found to be important to obtain the brookite phase because the intermediate complex leading to the brookite phase consumes more OH- than other phases like the rutile.

  14. INTERACTION OF POLYVINYLPYRROLIDONE WITH METAL CHLORIDE AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Mohammad Saleem Khan; Khaista Gul; Najeeb Ur Rehman

    2004-01-01

    Interactions of polyvinylpyrrolidone (PVP) with metal chlorides (MgCl2, CaCl2, KC1 and BaC12) have been investigated by viscometric and spectrophotometric techniques in aqueous solutions. Intrinsic viscosity [η] of (PVP) has shown a discontinuity with varying concentration of metal chlorides. The decreasing order of effectiveness of cation is K1+>Ca2+> Mg2+> Ba2+ for poly(vinylpyrrolidone) solution. Changes in the absorption spectra of the cosolutes were observed in the presence of PVP in the lower limit of the UV-visible region i.e. 200-210 nm. These changes were attributed to interaction of PVP molecules with the cosolute molecules. As the concentration of the cosolute increased, a red shift in the peaks was observed, indicating an increase in interaction between PVP and cosolutes.

  15. Multi-scale modelling of uranyl chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Thanh-Nghi; Duvail, Magali, E-mail: magali.duvail@icsm.fr; Villard, Arnaud; Dufrêche, Jean-François, E-mail: jean-francois.dufreche@univ-montp2.fr [Institut de Chimie Séparative de Marcoule (ICSM), UMR 5257, CEA-CNRS-Université Montpellier 2-ENSCM, Site de Marcoule, Bâtiment 426, BP 17171, F-30207 Bagnols-sur-Cèze Cedex (France); Molina, John Jairo [Fukui Institute for Fundamental Chemistry, Kyoto University, Takano-Nishihiraki-cho 34-4, Sakyo-ku, Kyoto 606-8103 (Japan); Guilbaud, Philippe [CEA/DEN/DRCP/SMCS/LILA, Marcoule, F-30207 Bagnols-sur-Cèze Cedex (France)

    2015-01-14

    Classical molecular dynamics simulations with explicit polarization have been successfully used to determine the structural and thermodynamic properties of binary aqueous solutions of uranyl chloride (UO{sub 2}Cl{sub 2}). Concentrated aqueous solutions of uranyl chloride have been studied to determine the hydration properties and the ion-ion interactions. The bond distances and the coordination number of the hydrated uranyl are in good agreement with available experimental data. Two stable positions of chloride in the second hydration shell of uranyl have been identified. The UO{sub 2}{sup 2+}-Cl{sup −} association constants have also been calculated using a multi-scale approach. First, the ion-ion potential averaged over the solvent configurations at infinite dilution (McMillan-Mayer potential) was calculated to establish the dissociation/association processes of UO{sub 2}{sup 2+}-Cl{sup −} ion pairs in aqueous solution. Then, the association constant was calculated from this potential. The value we obtained for the association constant is in good agreement with the experimental result (K{sub UO{sub 2Cl{sup +}}} = 1.48 l mol{sup −1}), but the resulting activity coefficient appears to be too low at molar concentration.

  16. Structure of concentrated aqueous solutions of scandium chloride

    Science.gov (United States)

    Smirnov, P. R.; Grechin, O. V.

    2017-03-01

    It is shown via X-ray diffraction that aqueous solutions of scandium chloride form ionic associates in a wide range of concentrations. It is established that the Sc3+ ion coordination number increases upon dilution to 8.2 at an unchanged Sc3+-OH2 distance of 0.215 nm. The second coordination sphere of the cation forms at an average distance of 0.420 nm. The number of solvent molecules in the sphere logically increases during dilution. It is concluded that the anion does not form its own sphere in highly concentrated solutions. This coordination sphere begins to form only in solutions with moderate concentrations at a distance of 0.315 nm, and it contains six water molecules in diluted solutions.

  17. Benzotriazole as an inhibitor of brass corrosion in chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Kosec, Tadeja [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Milosev, Ingrid [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Orthopaedic Hospital Valdoltra, Jadranska c. 31, 6280 Ankaran (Slovenia)], E-mail: ingrid.milosev@ijs.si; Pihlar, Boris [Faculty of Chemistry and Chemical Technology, University of Ljubljana, Askerceva 5, 1000 Ljubljana (Slovenia)

    2007-09-15

    The current research explores the formation of protective layers on copper, zinc and copper-zinc (Cu-10Zn and Cu-40Zn) alloys in chloride solution containing benzotriazole (BTAH), by use of electrochemical techniques, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Electrochemical reactions and surface products formed at the open circuit potential and as a function of the potential range are discussed. The addition of benzotriazole to aerated, near neutral 0.5 M NaCl solution affects the dissolution of copper, zinc, Cu-10Zn and Cu-40Zn alloys. The research also compares the inhibition efficiency and Gibbs adsorption energies of the investigated process. Benzotriazole, generally known as an inhibitor of copper corrosion is also shown to be an efficient inhibitor for copper-zinc alloys and zinc metal. The surface layer formed on alloys in BTAH-inhibited solution comprised both oxide and polymer components, namely Cu{sub 2}O and ZnO oxides, and Cu(I)-BTA and Zn(II)-BTA polymers. The formation of this mixed copper-zinc oxide polymer surface film provides an effective barrier against corrosion of both metal components in chloride solution.

  18. Electrochemical Behavior of Copper in Thionyl Chloride Solutions.

    Science.gov (United States)

    1980-12-01

    lithium - thionyl chloride batteries . Thionyl chloride is known *3 to react...electrolyte for lithium - thionyl chloride batteries . 8R. K. McAlpine and B. A. Soule, Prescott and Johnson’s Qualitative Chemical Analysis, D. Van...black carbon electrodes, cupric chloride appears to be a useful cathode additive for lithium - thionyl chloride batteries . Preliminary results2l

  19. Effects of Organic Corrosion Inhibitor and Chloride Ion Concentration on Steel Depassivation and Repassivation in Solution

    Institute of Scientific and Technical Information of China (English)

    WANG Zixiao; YU Lei; LIU Zhiyong; SONG Ning

    2015-01-01

    Effect of an organic corrosion inhibitor (OCI) named PCI-2014 added in chloride solution on the critical chlo-ride concentration of mild steel depassivation and the critical OCI concentrations for repairing the steel in different chlo-ride solution were investigated. The results show that the critical chloride concentration increases exponentially with raises of PCI-2014 concentration in the solution. Within a certain chloride ion concentration range, the critical PCI-2014 concentration for repairing the corroded steel is also increases exponentially with enhancement of chloride content in the solution. Atomic force microscopy images display the molecular particles of inhibitor are adsorbed on the steel surface and formed a protective layer. Analysis of X-ray photoelectron spectroscopy shows the chloride ions at the surface of steel are displaced by atoms or molecules of the inhibitor in chloride condition.

  20. Effects of Organic Corrosion Inhibitor and Chloride Ion Concentration on Steel Depassivation and Repassivation in Solution

    Institute of Scientific and Technical Information of China (English)

    WANG; Zixiao; YU; Lei; LIU; Zhiyong; SONG; Ning

    2015-01-01

    Effect of an organic corrosion inhibitor(OCI) named PCI-2014 added in chloride solution on the critical chloride concentration of mild steel depassivation and the critical OCI concentrations for repairing the steel in different chloride solution were investigated.The results show that the critical chloride concentration increases exponentially with raises of PCI-2014 concentration in the solution.Within a certain chloride ion concentration range,the critical PCI-2014 concentration for repairing the corroded steel is also increases exponentially with enhancement of chloride content in the solution.Atomic force microscopy images display the molecular particles of inhibitor are adsorbed on the steel surface and formed a protective layer.Analysis of X-ray photoelectron spectroscopy shows the chloride ions at the surface of steel are displaced by atoms or molecules of the inhibitor in chloride condition.

  1. Subdaily Earth rotation model and GPS solutions

    Science.gov (United States)

    Panafidina, Natalia; Hugentobler, Urs; Seitz, Manuela

    2014-05-01

    In this contribution we study the influence of the subdaily Earth rotation model on the GPS solution including station coordinates, satellite orbits and daily Earth rotation parameters (ERPs). The approach used is based on the transformation of GPS normal equation systems: free daily normal equations containing ERPs with 1-hour resolution are used as input data, in this case the high-frequency ERPs can be transformed into tidal terms which then can be fixed to new a priori values, thus changing implicitly the underlying subdaily Earth rotation model. To study the influence of individual tidal terms on the solution we successively changed a priori values for one tidal term in polar motion and compared the resulting solutions for GPS orbits, station coordinates and daily ERPs for a time interval of 13 years. The comparison reveals periodic changes in all estimated parameters with periods depending on the periods of the changed tidal terms. The dynamical reference frame realized by the GPS orbits is also affected: the whole satellite constellation shows periodic orientation variations, and each individual satellite shows periodic changes in the position of the orbit origin. We present a mechanism showing how errors in the subdaily Earth rotation model are propagated into the dynamical reference frame and the estimated parameters. Our model represents a change in one tidal term over one day as the sum of a prograde diurnal wave, a retrograde diurnal wave and an offset and linear drift in x- and y-pole. We demonstrate that this simple model, in conjunction with appropriate constraints, can explain well the observed variations in a one day GPS solution as well as in daily pole rates caused by changes in the subdaily Earth rotation model.

  2. Evaluation of cetylpyridinium chloride for infection control in storage solution.

    Science.gov (United States)

    Ziskind, D; Gleitman, J; Rotstein, I; Friedman, M

    2003-05-01

    Storage solution is used in in vitro experimental studies to prevent dehydration of teeth collected immediately after extraction and to prevent bacterial and fungal growth in the storage media. The chemical nature of the storing agent may affect the tooth structure and material properties at the tested interface. The aim of this study was to evaluate the use of 0.1% cetylpyridinium chloride (CPC) as a new storage solution and to assess the possible effect of 0.1% thymol on microleakage and bond strength. Forty extracted human teeth were collected from 10 different dental clinics. Immediately after extraction, the teeth were randomly divided and immersed in four different storage solutions. Two test solutions of 0.1% CPC (group C) and 0.1% thymol (group T) were compared with phosphate-buffered saline (Group S - positive control) and to 3% H2O2 (group H - negative control). Bond strength test and dye penetration evaluation were then carried out. The findings suggest that the use of 0.1% CPC as storage solution does not affect bond strength to enamel. However, it may increase dye penetration at the cervical margin. The effect of 0.1% thymol on shear bond strength and dye penetration is similar to the effect of phosphate-buffered saline.

  3. Leaching of complex sulphide concentrate in acidic cupric chloride solutions

    Institute of Scientific and Technical Information of China (English)

    M. TCHOUMOU; M. ROYNETTE

    2007-01-01

    The chemical analysis of a complex sulphide concentrate by emission spectrometry and X-ray diffraction shows that it contains essentially copper, lead, zinc and iron in the form of chalcopyrite, sphalerite and galena. A small amount of pyrite is also present in the ore but does not be detected with X-ray diffraction. The cupric chloride leaching of the sulphide concentrate at various durations and solid/liquid ratios at 100 ℃ shows that the rate of dissolution of the ore is the fastest in the first several hours, and after 12 h it does not evolve significantly. If oxygen is excluded from the aqueous cupric chloride solution during the leaching experiment at 100 ℃, the pyrite in the ore will not be leached. The determination of principal dissolved metals in the leaching liquor by flame atomic absorption spectrometry, and the chemical analysis of solid residues by emission spectrometry and X-ray diffraction allow to conclude that the rate of dissolution of the minerals contained in the complex sulphide concentrate are in the order of galena>sphalerite>chalcopyrite.

  4. Complex sulphide-barite ore leaching in ferric chloride solution

    Directory of Open Access Journals (Sweden)

    Miroslav Sokić

    2016-06-01

    Full Text Available The results of research on the leaching process of complex sulphide-barite ore were presented in this paper. The leaching process was carried out in a laboratory autoclave by ferric chloride solution. Considering that those minerals are represented in complex structural-textural relationships, it is not possible to extract lead, zinc and copper minerals from ore by flotation methods. The obtained results confirmed possibility of the ore processing directly, by chemical methods. The effect of temperature, time and oxygen partial pressure on the lead, zinc and copper dissolution was studied. The maximal leaching degree was achieved at 100 °C and amount of 91.5 % for Pb, 96.1 % for Zn and 60.7 % for Cu. Leaching at temperatures above 100 °C is impractical.

  5. Corrosion of LY12 aluminum alloy in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    程英亮; 张昭; 曹发和; 李劲风; 张鉴清; 王建明; 曹楚南

    2003-01-01

    The corrosion behavior of LY12 alloy in sodium chloride solution and its electrochemical noise were reported. The development of the micro-pits on the alloy surface was monitored by scanning electron microscopy, scanning tunneling microscopy, and electrochemical noise method. All the measurements show that the corrosion of LY12 alloy can be divided into two stages: a very reactive initial stage and a relative constant stable stage. The initial stage is corresponded to the adsorption of Cl ions and its reaction with the oxide film and the dissolution of Mg containing particles. The stable stage is corresponded to the development of the micro-pits by the galvanic attack formed by Al-Fe-Cu-Mn containing particles and the matrix. The initial stage lasts about 2-3 h while the stable stage dominates the whole corrosion process.

  6. Direct spectrophotometric determination of Nd in mixed rare earths with Semi-Xylenol Orange and cetylpyridinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Naixing Wang (Shandong Univ., Jinan, SD (China))

    1991-07-01

    The derivative absorption spectra of the neodymium complex with Semi-Xylenol Orange and cetylpyridinium chloride has been investigated. The characteristic absorption of the complex is {approx}350 times that of neodymium chloride. The fourth-order derivative spectrum has been used to eliminate the interference of the other lanthanides, and to increase the sensitivity by a further factor of 6. Beer's law is obeyed for 0-7.5 {mu}g of Nd in 25 ml of solution. The relative standard deviation for 7 determinations of 1.8 {mu}g/25 ml neodymium was 1.3%. The detection limits were 5.8 ng/ml in the absence of lanthanum and 11.2 ng/ml in the presence of 44 ng/ml lanthanum (or 36 ng/ml yttrium). The method has been used for the determination of neodymium in mixed rare earths, with satisfactory results. (author).

  7. The Effect of Silver Chloride Formation on the Kinetics of Silver Dissolution in Chloride Solution

    Science.gov (United States)

    Ha, Hung; Payer, Joe

    2011-01-01

    The precipitation and growth of AgCl on silver in physiological NaCl solution were investigated. AgCl was found to form at bottom of scratches on the surface which may be the less effective sites for diffusion or the favorable sites for heterogeneous nucleation. Patches of silver chloride expanded laterally on the substrate until a continuous film formed. The ionic transport path through this newly formed continuous film was via spaces between AgCl patches. As the film grew, the spaces between AgCl patches closed and ion transport was primarily via micro-channels running through AgCl patches. The decrease of AgCl layer conductivity during film growth were attributed to the clogging of micro-channels or decrease in charge carrier concentration inside the micro-channels. Under thin AgCl layer, i.e. on the order of a micrometer, the dissolution of silver substrate was under mixed activation-Ohmic control. Under thick AgCl layer, i.e. on the order of tens of micrometers, the dissolution of silver substrate was mediated by the Ohmic resistance of AgCl layer. PMID:21516171

  8. The Effect of Silver Chloride Formation on the Kinetics of Silver Dissolution in Chloride Solution.

    Science.gov (United States)

    Ha, Hung; Payer, Joe

    2011-02-28

    The precipitation and growth of AgCl on silver in physiological NaCl solution were investigated. AgCl was found to form at bottom of scratches on the surface which may be the less effective sites for diffusion or the favorable sites for heterogeneous nucleation. Patches of silver chloride expanded laterally on the substrate until a continuous film formed. The ionic transport path through this newly formed continuous film was via spaces between AgCl patches. As the film grew, the spaces between AgCl patches closed and ion transport was primarily via micro-channels running through AgCl patches. The decrease of AgCl layer conductivity during film growth were attributed to the clogging of micro-channels or decrease in charge carrier concentration inside the micro-channels. Under thin AgCl layer, i.e. on the order of a micrometer, the dissolution of silver substrate was under mixed activation-Ohmic control. Under thick AgCl layer, i.e. on the order of tens of micrometers, the dissolution of silver substrate was mediated by the Ohmic resistance of AgCl layer.

  9. Kinetics of coal desulfurization using cupric chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Ghazali, S.; Muharam, C.; Sani, S.A. [Bandung Inst. of Tech. (Indonesia)

    1995-12-31

    Coal desulfurization prior to combustion can be carried out either by physical or chemical methods. The physical methods, where the elimination of sulfur compounds is based on the difference of physical properties between pyritic sulfur and organic matrix, have progressed significantly and are currently used in commercial practice. These methods are, however, ineffective to remove organic sulfurs where S is attached chemically to carbon in the coal matrix. These compounds, presumed to be mercaptan, thyophene, organic sulfides or organic disulfide, could only be removed by chemical treatments. This paper describes the experimental study of coal beneficiation by chemical methods using cupric chloride solution. The results obtained showed that both organic and pyritic sulfurs were reduced significantly. It was also observed that cupric ions have reacted with in fraction of coal which was assumed to be some oxygenated carbon. The kinetics study has shown that the reaction rate of pyrite pseudo homogenous model and the reaction rates of organic sulfur generated coal fractions follow the power law models. (author). 5 tabs., 4 figs., 10 refs.

  10. EFFECT OF DIATOMEAOUS EARTH TREATMENT USING HYDROGEN CHLORIDE AND SULFURIC ACID ON KINETICS OF CADMIUM(II ADSORPTION

    Directory of Open Access Journals (Sweden)

    Nuryono Nuryono

    2010-06-01

    Full Text Available In this research, treatment of diatomaceous earth, Sangiran, Central Java using hydrogen chloride (HCl and sulfuric acid (H2SO4 on kinetics of Cd(II adsorption in aqueous solution has been carried out. The work was conducted by mixing an amount of grounded diatomaceous earth (200 mesh in size with HCl or H2SO4 solution in various concentrations for two hours at temperature range of 100 - 150oC. The mixture was then filtered and washed with water until the filtrate pH is approximately 7 and then the residue was dried for four hours at a temperature of 70oC. The product was used as an adsorbent to adsorb Cd(II in aqueous solution with various concentrations. The Cd(II adsorbed was determined by analyzing the rest of Cd(II in the solution using atomic absorption spectrophotometry. The effect of treatment was evaluated from kinetic parameter of adsorption rate constant calculated based on the simple kinetic model. Results showed  that before equilibrium condition reached, adsorpstion of Cd(II occurred through two steps, i.e. a step tends to follow a reaction of irreversible first order  (step I followed by reaction of reversible first order (step II. Treatment with acids, either hydrogen chloride or sulfuric acid, decreased adsorption rate constant for the step I from 15.2/min to a range of 6.4 - 9.4/min.  However, increasing concentration of acid (in a range of concentration investigated did not give significant and constant change of adsorption rate constant. For step II process,  adsorption involved physical interaction with the sufficient low adsorption energy (in a range of 311.3 - 1001 J/mol.     Keywords: adsorption, cdmium, diatomaceous earth, kinetics.

  11. Stress Corrosion Cracking of an Austenitic Stainless Steel in Nitrite-Containing Chloride Solutions

    Directory of Open Access Journals (Sweden)

    R. K. Singh Raman

    2014-12-01

    Full Text Available This article describes the susceptibility of 316L stainless steel to stress corrosion cracking (SCC in a nitrite-containing chloride solution. Slow strain rate testing (SSRT in 30 wt. % MgCl2 solution established SCC susceptibility, as evidenced by post-SSRT fractography. Addition of nitrite to the chloride solution, which is reported to have inhibitive influence on corrosion of stainless steels, was found to increase SCC susceptibility. The susceptibility was also found to increase with nitrite concentration. This behaviour is explained on the basis of the passivation and pitting characteristics of 316L steel in chloride solution.

  12. Solubilities ,Densities and Refractive Indices of Rubidium Chloride or Cesium Chloride in Ethanol Aqueous Solutions at Different Temperatures

    Institute of Scientific and Technical Information of China (English)

    ZHAO,Wen-Xia; HU,Man-Cheng; JIANG,Yu-Cheng; LI,Shu-Ni

    2007-01-01

    The data of solubilities.densities and refractive indices of rubidium chloride or cesium chloride in the system C2H5OH-H2O were measured by using a simple accurate analytical method at different temperatures,with mass fractions of ethanol in the range of O to 1.0.In all cases,the presence of ethanol significantly reduced the solubility of rubidium chloride and cesium chloride in aqueous solution.The solubilities of the saturated solutions were fitted via polynomial equations as a function of the mass fraction of ethanol.The CsCl-C2H5OH-H2O temary system appeared in two liquid phases:alcoholic phase and water phase.when the mass fractions of ethanol were in the range of 10.37% to 49.59%at 35℃.Density and refractive index were also determined for the same ternary systems with varied unsaturated salt concentrations.Values for both experiment and theory were correlated with the salt concentrations and proportions of alcohol in the solutions.The equations proposed could also account for the saturated solutions.

  13. Chloride content and pH value in the pore solution of concrete under carbonation

    Institute of Scientific and Technical Information of China (English)

    Xiao-mei WAN; Folker H.WITTMANN; Tie-jun ZHAO; Hong FAN

    2013-01-01

    Chloride content and the pH value of the pore solution in the neighborhood of steel reinforcement are decisive parameters for initiation and rate of corrosion.The pore solution of cement mortar and hardened cement paste has been expressed from the pore space by high pressure in the investigation.The influence of the water-cement ratio,age,and addition of chloride to the fresh mix on chloride content in the pore solution has been determined by ion chromatography.At the same time the pH value of the pore solution has been determined.The dissolved chloride content decreases with increase in the water-cement ratio.The amount of bound chloride increases with time,but it decreases with decreasing content of dissolved chloride in the pore solution.A significant influence of carbonation on the dissolved chloride content of the pore solution has been observed.With complete carbonation,the dissolved chloride content in cement mortar and hardened cement paste increases by a factor between 2 and 12.The bound chloride decreases by 27%-54%.As expected,the pH value decreases from around 13.2 to as low as 8.0 due to carbonation.It can be concluded that carbonation not only lowers the pH value but liberates bound chloride.This is one obvious reason why the combined action of chloride penetration and carbonation accelerates steel corrosion and shortens the service life of reinforced concrete structures.

  14. Separation of Ce and La from Synthetic Chloride Leach Solution of Monazite Sand by Precipitation and Solvent Extraction

    Science.gov (United States)

    Banda, Raju; Jeon, Ho Seok; Lee, Man Seung

    2014-12-01

    Precipitation and solvent extraction experiments have been performed to recover light rare earths from simulated monazite sand chloride leach solutions. Precipitation conditions were obtained to recover Ce by adding NaClO as an oxidant. Among some cationic extractants (PC 88A, D2EHPA, Cyanex 272, LIX 63), PC 88A showed the best performance to separate La from the resulting chloride solution. Furthermore, the mixture of PC 88A with other solvating (TBP, TOPO) and amine extractants (Alamine 336, Aliquat 336) was tested to increase the separation factor of La from Pr and Nd. The use of mixed extractants greatly enhanced the separation of La from the two other metals. McCabe-Thiele diagrams for the extraction of Pr and Nd with the PC 88A/Alamine 336 mixture were constructed.

  15. Chloride stress corrosion cracking of Alloy 600 in boric acid solutions

    Energy Technology Data Exchange (ETDEWEB)

    Berge, Ph. [Electricite de France, 92 - Paris la Defense (France); Noel, D.; Gras, J.M.; Prieux, B. [Electricite de France, 77 - Moret-sur-Loing (France). Direction des Etudes et Recherches

    1997-10-01

    The high nickel austenitic alloys are generally considered to have good resistance to chloride stress corrosion cracking. In the standard boiling magnesium chloride solution tests, alloys with more than 40% nickel are immune. Nevertheless, more recent data show that cracking can occur in both Alloys 600 and 690 if the solution is acidified. In other low pH media, such as boric acid solution at 100 deg C, transgranular and intergranular cracking are observed in Alloy 600 in the presence of minor concentrations of sodium chloride (2g/I). In concentrated boric acid at higher temperatures (250 and 290 deg C), intergranular cracking also occurs, either when the chloride concentration is high, or at low chloride contents and high oxygen levels. The role of pH and a possible specific action of boric acid are discussed, together with the influence of electrochemical potential. (author) 21 refs.

  16. Mechanical properties of cement mortar in sodium sulfate and sodium chloride solutions

    Institute of Scientific and Technical Information of China (English)

    熊良宵; 虞利军

    2015-01-01

    To investigate the mechanical properties of cement mortar in sodium sulfate and sodium chloride solutions, uniaxial compression test and ultrasonic test were performed. Test results show that the relative dynamic elastic modulus, the mass variation, and the compressive strength of cement mortar increase first, and then decrease with increasing erosion time in sodium sulfate and sodium chloride solutions. The relative dynamic elastic moduli and the compressive strengths of cement mortars with water/cement ratios of 0.55 and 0.65 in sodium sulfate solution are lower than those in sodium chloride solution with the same concentration at the 420th day of immersion. The compressive strength of cement mortar with water/cement ratio of 0.65 is more sensitive to strain rate than that with water/cement ratio of 0.55. In addition, the strain-rate sensitivity of compressive strength of cement mortar will increase under attacks of sodium sulfate or sodium chloride solution.

  17. A reactive distillation process for the treatment of LiCl-KCl eutectic waste salt containing rare earth chlorides

    Science.gov (United States)

    Eun, H. C.; Choi, J. H.; Kim, N. Y.; Lee, T. K.; Han, S. Y.; Lee, K. R.; Park, H. S.; Ahn, D. H.

    2016-11-01

    The pyrochemical process, which recovers useful resources (U/TRU metals) from used nuclear fuel using an electrochemical method, generates LiCl-KCl eutectic waste salt containing radioactive rare earth chlorides (RECl3). It is necessary to develop a simple process for the treatment of LiCl-KCl eutectic waste salt in a hot-cell facility. For this reason, a reactive distillation process using a chemical agent was achieved as a method to separate rare earths from the LiCl-KCl waste salt. Before conducting the reactive distillation, thermodynamic equilibrium behaviors of the reactions between rare earth (Nd, La, Ce, Pr) chlorides and the chemical agent (K2CO3) were predicted using software. The addition of the chemical agent was determined to separate the rare earth chlorides into an oxide form using these equilibrium results. In the reactive distillation test, the rare earth chlorides in LiCl-KCl eutectic salt were decontaminated at a decontamination factor (DF) of more than 5000, and were mainly converted into oxide (Nd2O3, CeO2, La2O3, Pr2O3) or oxychloride (LaOCl, PrOCl) forms. The LiCl-KCl was purified into a form with a very low concentration (<1 ppm) for the rare earth chlorides.

  18. Corrosion Inhibition of Carbon Steel in Chloride and Sulfate Solutions

    Directory of Open Access Journals (Sweden)

    Amr Ahmed Elsayed

    2016-02-01

    Full Text Available Corrosion is a major problem in industry and in infrastructure; a huge sum of expenditure every year is spent on preventing, retarding, and repairing its damages. This work studies the engineering of an inhibitor for carbon steel metal used in the cooling systems containing high concentration of chloride and sulfate ions. For this purpose, the synergy between the dichromate, molybdate and nitrite inhibitors is examined and optimized to the best results. Moreover, care was taken that the proposed inhibitor is compliant with the environmental laws and regulations.

  19. A Spherical Earth Solution for TOA Lightning Location Retrieval

    Science.gov (United States)

    Koshak, W. J.; Solakiewicz, R. J.

    1999-01-01

    The problem of retrieving ligntning, ground-strike location on a spherical Earth surface using a network of 4 or more time-of-arrival (TOA) sensors is considered, It is shown that this problem has an analytic solution and therefore does not require the use of nonlinear estimation theory (e.g., minimization). The mathematical robustness of the analytic solution is tested using computer-generated lightning sources and simulated TOA measurement errors. A summary of a quasi-analytic extension of the spherical Earth solution to an oblate spheroid Earth geometry is also provided.

  20. The initial behaviour of freshly etched copper in modertely acid, aerated chloride solutions

    DEFF Research Database (Denmark)

    Bech-Nielsen, Gregers; Jaskula, M.; Chorkendorff, Ib;

    2002-01-01

    When freshly etched samples of various types of copper were exposed in moderately acid, aerated chloride solutions, two phenomena were observed. First the corrosion potential and the pH of the solution decreased over a shorter time, then the potential increased over a long period (600-1500 min), ...

  1. Nickel electrodeposition from leaching solution containing ammonia and chloride

    Institute of Scientific and Technical Information of China (English)

    郑国渠; 郑利峰; 曹华珍; 高志峰; 倪似愚; 张九渊

    2003-01-01

    The effects of temperature, nickel concentration and current density on the current efficiency and the e-lectrolyzer voltage were investigated in the process of electrowinning nickel. The results show that the current effi-ciency is above 90 % under the various experimental conditions, and the electrolyzer voltage is less than that of tradi-tional electrolyzer system. Therefore, the optimized parameters, i.e. temperature of 50 C, current density of 400A/m2 , are determined. It is also elucidated that anodic product is high valent nickel compound in the process of elec-trodeposition in terms of X-ray diffraction and chemical analysis. The amount of solid product formed on the elec-trode surface decreases with an increase in ammonium chloride concentration by cyclic voltammetry analysis. It is al-so indicated that the anodic gas species are mainly composed of nitrogen by vapor phase chromatograph.

  2. Redox flow batteries based on supporting solutions containing chloride

    Energy Technology Data Exchange (ETDEWEB)

    Li, Liyu; Kim, Soowhan; Yang, Zhenguo; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Xia, Guanguang

    2014-01-14

    Redox flow battery systems having a supporting solution that contains Cl.sup.- ions can exhibit improved performance and characteristics. Furthermore, a supporting solution having mixed SO.sub.4.sup.2- and Cl.sup.- ions can provide increased energy density and improved stability and solubility of one or more of the ionic species in the catholyte and/or anolyte. According to one example, a vanadium-based redox flow battery system is characterized by an anolyte having V.sup.2+ and V.sup.3+ in a supporting solution and a catholyte having V.sup.4+ and V.sup.5+ in a supporting solution. The supporting solution can contain Cl.sup.- ions or a mixture of SO.sub.4.sup.2- and Cl.sup.- ions.

  3. Redox flow batteries based on supporting solutions containing chloride

    Energy Technology Data Exchange (ETDEWEB)

    Li, Liyu; Kim, Soowhan; Yang, Zhenguo; Wang, Wei; Nie, Zimin; Chen, Baowei; Zhang, Jianlu; Xia, Guanguang

    2015-07-07

    Redox flow battery systems having a supporting solution that contains Cl.sup.- ions can exhibit improved performance and characteristics. Furthermore, a supporting solution having mixed SO.sub.4.sup.2- and Cl.sup.- ions can provide increased energy density and improved stability and solubility of one or more of the ionic species in the catholyte and/or anolyte. According to one example, a vanadium-based redox flow battery system is characterized by an anolyte having V.sup.2+ and V.sup.3+ in a supporting solution and a catholyte having V.sup.4+ and V.sup.5+ in a supporting solution. The supporting solution can contain Cl.sup.- ions or a mixture of SO.sub.4.sup.2- and Cl.sup.- ions.

  4. Redox flow batteries based on supporting solutions containing chloride

    Energy Technology Data Exchange (ETDEWEB)

    Li, Liyu; Kim, Soowhan; Yang, Zhenguo; Wang, Wei; Nie, Zimin; Chen, Baowei; Zhang, Jianlu; Xia, Guanguang

    2015-09-01

    Redox flow battery systems having a supporting solution that contains Cl.sup.- ions can exhibit improved performance and characteristics. Furthermore, a supporting solution having mixed SO.sub.4.sup.2- and Cl.sup.- ions can provide increased energy density and improved stability and solubility of one or more of the ionic species in the catholyte and/or anolyte. According to one example, a vanadium-based redox flow battery system is characterized by an anolyte having V.sup.2+ and V.sup.3+ in a supporting solution and a catholyte having V.sup.4+ and V.sup.5+ in a supporting solution. The supporting solution can contain Cl.sup.- ions or a mixture of SO.sub.4.sup.2- and Cl.sup.- ions.

  5. Effect of metal chloride solutions on coloration and biaxial flexural strength of yttria-stabilized zirconia

    Science.gov (United States)

    Oh, Gye-Jeong; Lee, Kwangmin; Lee, Doh-Jae; Lim, Hyun-Pil; Yun, Kwi-Dug; Ban, Jae-Sam; Lee, Kyung-Ku; Fisher, John G.; Park, Sang-Won

    2012-10-01

    The effect of three kinds of transition metal dopants on the color and biaxial flexural strength of zirconia ceramics for dental applications was evaluated. Presintered zirconia discs were colored through immersion in aqueous chromium, molybdenum and vanadium chloride solutions and then sintered at 1450 °C. The color of the doped specimens was measured using a digital spectrophotometer. For biaxial flexural strength measurements, specimens infiltrated with 0.3 wt% of each aqueous chloride solution were used. Uncolored discs were used as a control. Zirconia specimens infiltrated with chromium, molybdenum and vanadium chloride solutions were dark brown, light yellow and dark yellow, respectively. CIE L*, a*, and b* values of all the chromium-doped specimens and the specimens infiltrated with 0.1 wt% molybdenum chloride solution were in the range of values for natural teeth. The biaxial flexural strengths of the three kinds of metal chloride groups were similar to the uncolored group. These results suggest that chromium and molybdenum dopants can be used as colorants to fabricate tooth colored zirconia ceramic restorations.

  6. Recovery of nickel, cobalt, copper and zinc in sulphate and chloride solutions using synergistic solvent extraction

    Institute of Scientific and Technical Information of China (English)

    Chu Yong Cheng; Keith R. Barnard; Wensheng Zhang; Zhaowu Zhu; Yoko Pranolo

    2016-01-01

    A number of synergistic solvent extraction (SSX) systems have been developed to recover nickel, cobalt, zinc and copper from sulphuric and chloride leach solutions by the solvent extraction team of CSIRO, Australia. These in-clude (1) Versatic 10/CLX50 system for the separation of Ni from Ca in sulphate solutions, (2) Versatic 10/4PC system for the separation of Ni and Co from Mn/Mg/Ca in sulphate solutions, (3) Cyanex 471X/HRJ-4277 system for the separation of Zn from Cd in sulphate solutions, (4) Versatic 10/LIX63 system for the separation of Co from Mn/Mg/Ca in sulphate solutions, (5) Versatic 10/LIX63/TBP system for separation of Ni and Co from Mn/Mg/Ca in sulphate solutions, (6) Versatic 10/LIX63 system for the separation of cobalt from nickel in sulphate solutions by difference in kinetics, (7) Cyanex 272/LIX84 system for the separation of Cu/Fe/Zn from Ni/Co in sulphate solutions, (8) Versatic 10/LIX63/TBP system to recover Cu/Ni from strong chloride solutions, and (9) Versatic 10/LIX63 system to separate Cu from Fe in strong chloride solutions. The synergistic effect on metal separation and efficiency is presented and possible industrial applications are demonstrated. The chemical stability of selected SSX systems is also reported.

  7. Zinc chloride aqueous solution as a solvent for starch.

    Science.gov (United States)

    Lin, Meiying; Shang, Xiaoqin; Liu, Peng; Xie, Fengwei; Chen, Xiaodong; Sun, Yongyi; Wan, Junyan

    2016-01-20

    It is important to obtain starch-based homogeneous systems for starch modification. Regarding this, an important key point is to find cheap, low-cost and low-toxicity solvents to allow complete dissolution of starch and its easy regeneration. This study reveals that a ZnCl2 aqueous solution is a good non-derivatizing solvent for starch at 50 °C, and can completely dissolve starch granules. The possible formation of a "zinc-starch complex" might account for the dissolution; and the degradation of starch, which was caused by the H(+) inZnCl2 aqueous solution, could not contribute to full dissolution. From polarized light microscopic observation combined with the solution turbidity results, it was found that the lowest ZnCl2 concentration for full dissolution was 29.6 wt.% at 50 °C, with the dissolving time being 4h. Using Fourier-transform infrared (FTIR), solid state (13)C nuclear magnetic resonance (NMR), and X-ray diffraction (XRD), it was revealed that ZnCl2 solution had no chemical reaction with starch glucosides, but only weakened starch hydrogen bonding and converted the crystalline regions to amorphous regions. In addition, as shown by intrinsic viscosity and thermogravimetric analysis (TGA), ZnCl2 solution caused degradation of starch macromolecules, which was more serious with a higher concentration of ZnCl2 solution.

  8. Thermodynamic equilibrium of bismuth hydrometallurgy in chloride and nitrate solutions

    Institute of Scientific and Technical Information of China (English)

    王云燕; 彭文杰; 柴立元

    2004-01-01

    Simultaneous equilibrium was applied to the thermodynamic analysis and calculation of Bi( Ⅲ )-X(Cl- ,NO3- )-H2O systems, based on which the diagrams of the logarithm of equilibrium concentration of Bi( Ⅲ ) of series precipitation vs pH value of these two systems at 25 ℃ were obtained, and the pH ranges of the stable zones of various precipitations were analyzed and determined. In Bi( Ⅲ )-Cl -H2O system, the variations of c0 (Bi3+) and c0 (Cl-) have little effect on the equilibria of Bi(OH)3-solution and BiOOH-solution, but has great influence on the equilibrium of BiOCl-solution. However, in Bi( Ⅲ )-NO3-H2O system, the variations of c0 (Bi3+) and C0 (NO3-)have little effect on equilibria of Bi(OH)3-solution, BiOOH-solution and Bi2O3-solution. When pH value is high,Bi2O3 is the thermodynamic stable phase, its stable zone is the widest, almost including the stable zones of BiOCl or BiONO3, Bi(OH)3 and BiOOH. Bi(OH)3 cannot be obtained from Bi( Ⅲ )-Cl--H2O system, even strong alkaline media. Bi2O3 can be obtained from the solution directly, and highly pure BiOCl or BiONO3 can also be obtained through strictly controlling pH value.

  9. Conductivity of Thionyl Chloride-Lithium Tetrachloroaluminate Solutions

    DEFF Research Database (Denmark)

    Berg, Rolf W.; Hjuler, H. A.; Søndergaard, A. P. L.;

    1989-01-01

    The specific conductivity of solutions of LiAlCl4 dissolved in SOCl2 was determined as a function of composition andtemperature. An analytical expression from which the conductivity can be calculated is given as a function of the molefraction of LiAlCl4 and temperature in the ranges from 0° to 0...

  10. Experimental study of concentrated solutions containing sodium and chloride pollutants in SG flow restricted areas

    Energy Technology Data Exchange (ETDEWEB)

    You, D.; Lefefre, S.; Feron, D. [CEA-Saclay, Lab. d' Etude de la Corrosion Aqueuse, Gif-sur-Yvette (France); Vaillant, F. [EDF-Les Renardieres - DRD/EMA, Moret-sur-Loing (France)

    2002-07-01

    In steam generators, the hideout processes occur in flow restricted areas. Non volatile pollutants, i.e. species less soluble in the vapour phase than in the liquid water phase, accumulate such as sodium hydroxide or sodium chloride. The thermodynamic equilibrium between these two phases is described in terms of liquid-vapour equilibrium constants for soluble species and boiling constant for the solvent. The presented experimental investigation has been realised with the EVA device: the boiling pressure evolution has been measured during the hideout process of sodium hydroxide and sodium chloride aqueous solutions. The results clearly demonstrated that high sodium hydroxide aqueous solutions are thermodynamically possible while with sodium chloride, it seems that precipitation occurs before. (authors)

  11. Recovery of rare earth elements from El-Sela effluent solutions

    Directory of Open Access Journals (Sweden)

    Y.M. Khawassek

    2015-10-01

    Full Text Available The study area of Gabal El Sela at Halaib environ is located at about 20 km west of Abu Ramad City, Egypt. An uraniferous ore material associated with REE was subjected to sulphuric acid leaching for the extraction of uranium mainly and REEs as a by-product. 93.9% of U and 60% of REEs content were leached using −0.5 mm ground ore with 100 g/l sulfuric acid, acid/ore ratio of 2.0 and agitate for 6 h at 40 °C. After uranium extraction, effluent solutions containing 135 ppm rare earths were treated with 30% ammonium hydroxide to pH of 9.3 to enhance the rare earth elements concentration. The precipitated cake was filtered then dried at 110 °C. The dried cake containing 16.2% rare earth elements was dissolved by hydrochloric acid at pH 1.0. The rare earths precipitated cakes of 36.9, 45.7 and 48.7% REEs were recovered successfully from the chloride leach liquor of 900 ppm rare earths by using 5% v/v from 50% HF, 6% wt/v oxalic acid and 4.8% wt/v oxalic acid to chloride solution with heating for one hour which respectively. 73.5% REEs precipitated cake was achieved by double precipitation, firstly by hydrofluoric acid followed by oxalic acid precipitation.

  12. Stability of Melphalan in 0.9% Sodium Chloride Solutions Prepared in Polyvinyl Chloride Bags for Intravenous Injection.

    Science.gov (United States)

    Desmaris, Romain-Pacôme; Mercier, Lionel; Paci, Angelo

    2015-09-01

    Melphalan is an alkylating agent frequently used in an intravenous formulation to treat hematologic malignancies and solid tumors in both adults and children. According to the manufacturer, melphalan is stable in sterile 0.9% sodium chloride for 90 min at room temperature (RT). Several authors have studied the stability of different concentrations of melphalan; however, most were not adapted to the current manufacturing process applied in pharmaceutical centralized units. This study was conducted to determine the stability of melphalan in 0.9% sodium chloride solutions at concentrations used for intravenous injection in practice. Melphalan is commonly prepared in diluted solutions ranging from 2 to 4 mg/ml for the treatment of adult patients and at lower concentrations (down to 0.5 mg/ml) for pediatric use. Accordingly, these were the three concentrations chosen for this study. Melphalan concentrations were measured with high-performance thin-layer chromatography (HPTLC). At RT, admixtures prepared at 4 mg/ml were stable for up to 8 h without protection from light; however, at lower concentrations, such as 0.5 and 2 mg/ml, stability did not exceed 2 h. When refrigerated, melphalan was stable for 24 h at 2 mg/ml; however, at 0.5 and 4 mg/ml, the drug was not stable. Melphalan solutions present with limited stability at 0.5, 2, and 4 mg/ml and are not adapted for delayed administration in pharmaceutical centralized units. However, at 4 mg/ml and at RT, a stability of 8 h is very interesting in practice and allows sufficient time for preparation, pharmaceutical control, transport, and administration.

  13. Aqueous Solution Thermal Conductivity of Beryllium-Subgroup Metal Chlorides

    Directory of Open Access Journals (Sweden)

    K. Abdullayev

    2013-01-01

    Full Text Available The paper presents experimental data on thermal conductivity of BeCl2 and SrCl2 salt aqueous solutions in the temperature range from 20 to 300 °С  and at various electrolyte concentrations  in mass percent. For the first time thermal conductivity of the system Н2О + BeCl2 has been investigated at high temperatures.The experimental results are described with the help of an empirical equation in the form of: λs = λo (1+ Am + Bm3/2 + Cm2,where λs  and λo – thermal conductivity coefficients of solution and water; A, B and C – coefficients depending on electrolyte nature; m – molality in units mol/kg.The formula error is less than  ±1 %.

  14. Experimental study of directional solidification of aqueous ammonium chloride solution

    Science.gov (United States)

    Chen, C. F.; Chen, Falin

    1991-01-01

    Directional solidification experiments have been carried out using the analog casting system of NH4Cl-H2O solution by cooling it from below with a constant-temperature surface ranging from -31.5 C to +11.9 C. The NH4Cl concentration was 26 percent in all solutions, with a liquidus temperature of 15 C. It was found that finger convection occurred in the fluid region just above the mushy layer in all experiments. Plume convection with associated chimneys in the mush occurred in experiments with bottom temperatures as high as +11.0 C. However, when the bottom temperature was raised to +11.9 C, no plume convection was observed, although finger convection continued as usual. A method has been devised to determine the porosity of the mush by computed tomography. Using the mean value of the porosity across the mush layer and the permeability calculated by the Kozeny-Carman relationship, the critical solute Rayleigh number across the mush layer for onset of plume convection was estimated to be between 200 and 250.

  15. Study on New Kind of Rare Earth-Containing Flocculants of Poly-Ferric Sulfate Chloride

    Institute of Scientific and Technical Information of China (English)

    Kuang Juchi; Li Jinai; Luo Yongjian; Pang Xijie; Xiao Xueyan; Zhu Hengxiang; Yao Jiye

    2004-01-01

    A new kind of rare earth- containing flocculant of poly-ferric sulfate chloride (PFSCRE) was studied, and proved to produce high density floccules growing, make sludge deposit quickly and possess high COD removal rate, so that it is seen to be more effective for the disposal of dying wastewater than PFSC. The optimum process for preparing the PFSCRE is defined as REC/PFSC 1.2% ~ 2.2%. And each correlativity of configuration with capacity of aggregating sludge was respectively educed through analysis and comparison of configurations of them. Finally, a prediction was put forward that it should be the key for development of the PFSCRE agglomerating capacity to manage to increase its degree .of polymerization.

  16. Erythrocyte lysis in isotonic solution of ammonium chloride: Theoretical modelling and experimental verification

    NARCIS (Netherlands)

    Chernyshev, A.V.; Tarasov, P.A.; Semianov, K.A.; Nekrasov, V.M.; Hoekstra, A.G.; Maltsev, V.P.

    2008-01-01

    A mathematical model of erythrocyte lysis in isotonic solution of ammonium chloride is presented in frames of a statistical approach. The model is used to evaluate several parameters of mature erythrocytes (volume, surface area, hemoglobin concentration, number of anionic exchangers on membrane, ela

  17. Sodium chloride methanol solution spin-coating process for bulk-heterojunction polymer solar cells

    Science.gov (United States)

    Liu, Tong-Fang; Hu, Yu-Feng; Deng, Zhen-Bo; Li, Xiong; Zhu, Li-Jie; Wang, Yue; Lv, Long-Feng; Wang, Tie-Ning; Lou, Zhi-Dong; Hou, Yan-Bing; Teng, Feng

    2016-08-01

    The sodium chloride methanol solution process is conducted on the conventional poly(3-hexylthiophene) (P3HT)/[6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) polymer bulk heterojunction solar cells. The device exhibits a power conversion efficiency of up to 3.36%, 18% higher than that of the device without the solution process. The measurements of the active layer by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and ultraviolet photoelectron spectroscopy (UPS) indicate a slight phase separation in the vertical direction and a sodium chloride distributed island-like interface between the active layer and the cathode. The capacitance-voltage (C-V) and impedance spectroscopy measurements prove that the sodium chloride methanol process can reduce the electron injection barrier and improve the interfacial contact of polymer solar cells. Therefore, this one-step solution process not only optimizes the phase separation in the active layers but also forms a cathode buffer layer, which can enhance the generation, transport, and collection of photogenerated charge carriers in the device simultaneously. This work indicates that the inexpensive and non-toxic sodium chloride methanol solution process is an efficient one-step method for the low cost manufacturing of polymer solar cells. Project supported by the Fundamental Research Funds for the Central Universities, China (Grant No. 2014JBZ009) and the National Natural Science Foundation of China (Grant Nos. 61274063, 61377028, 61475014, and 61475017).

  18. The determination of hydroxide and carbonate in concentrated sodium chloride solutions

    NARCIS (Netherlands)

    Roolvink, W.B.; Bos, M.

    1980-01-01

    A computer method for the determination of carbonate and hydroxide in concentrated (2.89 M) sodium chloride solutions is described. The method is based on multiparametric curve-fitting and can also be applied to salts of dibasic acids with unknown equilibrium constants. The systematic error is not m

  19. Stress corrosion cracking of AISI 321 stainless steel in acidic chloride solution

    Indian Academy of Sciences (India)

    Yanliang Huang

    2002-02-01

    The stress corrosion cracking (SCC) of AISI 321 stainless steel in acidic chloride solution was studied by slow strain rate (SSR) technique and fracture mechanics method. The fractured surface was characterized by cleavage fracture. In order to clarify the SCC mechanism, the effects of inhibitor KI on SCC behaviour were also included in this paper. A study showed that the inhibition effects of KI on SCC were mainly attributed to the anodic reaction of the corrosion process. The results of strain distribution in front of the crack tip of the fatigue pre-cracked plate specimens in air, in the blank solution (acidic chloride solution without inhibitor KI) and in the solution added with KI measured by speckle interferometry (SPI) support the unified mechanism of SCC and corrosion fatigue cracking (CFC).

  20. Stepwise aggregation of dimethyl-di-n-octylammonium chloride in aqueous solutions: from dimers to vesicles.

    Science.gov (United States)

    Leclercq, Loïc; Nardello-Rataj, Véronique; Turmine, Mireille; Azaroual, Nathalie; Aubry, Jean-Marie

    2010-02-01

    The self-aggregation of dimethyl-di-n-octylammonium chloride, in diluted aqueous solutions, was studied with various experimental and theoretical techniques: zetametry, conductimetry, dimethyl-di-n-octylammonium and chloride-selective electrodes, tensiometry, NMR spectroscopy ((1)H and DOSY), and molecular modeling (PM3 and molecular dynamic). The combination of the data obtained by these techniques led us to propose a stepwise aggregation process with increasing concentration: dimers (0.2-10 mM), bilayers (10-30 mM), and finally vesicles (>30 mM).

  1. Separation of hafnium from zirconium in their tetrachloride solution in molten alkali metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Salyulev, A.B.; Kudyakov, V.Ya.; Smirnov, M.V.; Moskalenko, N.I. (AN SSSR, Sverdlovsk. Inst. Ehlektrokhimii)

    1984-08-01

    The coefficient of HfCl/sub 4/ and ZrCl/sub 4/ separation in the process of vapour sublimation from their solutions in molten NaCl, KCl, CsCl, NaCl-KCl and NaCl-CsCl equimolar mixtures is found to vary in the series from approximately 1.10 to approximately 1.22 and practically not to depend on the temperature (in the 600-910 deg) range and concentration (2-25 mol.% ZrCl/sub 4/+HfCl/sub 4/). HfCl/sub 4/ and ZrCl/sub 4/ are shown to form almost perfect solutions with each other, which in their turn form imperfect solutions with molten alkali metal chlorides, with the strength of hafnium complex chloride anions increasing higher than that of zirconium in the series from NaCl to CsCl.

  2. Towards an understanding of solvent extraction--electroanalytical characterization of chloride-leaching solutions.

    Science.gov (United States)

    Paiva, A P; Abrantes, L M

    2001-08-01

    Solvent extraction has been employed to purify media simulating chloride-leaching solutions resulting from complex sulfide concentrate processing, and cyclic voltammetry (CV) has been chosen to characterize those hydrometallurgical aqueous phases. The possibilities of the CV technique were investigated by the evaluation of the adequacy of a specific organic extractant, triisobutylphosphine sulfide, aimed to efficiently and selectively extract silver from a complex chloride medium, additionally containing tenfold to 40-fold molar concentrations of iron, copper and lead. The influence of the oxidation state of the metallic ions present in the feed solution, namely Cu(II) and Cu(I), is considered. The possibilities of CV analysis for the characterization of stripping solutions are also illustrated.

  3. Efficient acetylation of primary amines and amino acids in environmentally benign brine solution using acetyl chloride

    Indian Academy of Sciences (India)

    Kaushik Basu; Suchandra Chakraborty; Achintya Kumar Sarkar; Chandan Saha

    2013-05-01

    Acetyl chloride is one of the most commonly available and cheap acylating agent but its high reactivity and concomitant instability in water precludes its use to carry out acetylation in aqueous medium. The present methodology illustrates the efficient acetylation of primary amines and amino acids in brine solution by means of acetyl chloride under weakly basic condition in the presence of sodium acetate and/or triethyl amine followed by trituration with aqueous saturated bicarbonate solution. This effort represents the first efficient use of this most reactive but cheap acetylating agent to acetylate amines in excellent yields in aqueous medium. This is a potentially useful green chemical transformation where reaction takes place in environment-friendly brine solution leading to easy work-up and isolation of the amide derivatives. Mechanistic rationale of this methodology is also important.

  4. Critical pitting temperature for Type 254 SMO stainless steel in chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Abd El Meguid, E.A. [Department of Electrochemistry and Corrosion, National Research Centre, Dokki, Cairo (Egypt)]. E-mail: eameguid_nrc@yahoo.com; Abd El Latif, A.A. [Department of Electrochemistry and Corrosion, National Research Centre, Dokki, Cairo (Egypt)

    2007-02-15

    The variation with time of the open circuit potential of high molybdenum containing stainless steel (Type 254 SMO) was measured in 4% sodium chloride solution in the temperatures range 30-100 deg. C. The plot of steady state potentials as function of temperature showed an inflection at 50 deg. C, attributed to the decrease of oxygen solubility in test solution above 50 deg. C. Potentiodynamic cycling anodic polarization technique was used to determine the critical pitting potential (E {sub pit}) and the critical protection potential (E {sub prot}) of the steel in 4-30% NaCl solutions at temperatures between 30 and 100 deg. C. By plotting the two values versus solution temperature, the corresponding critical pitting (CPT) and the critical protection (CPrT) temperatures were determined. Both parameters decreased with increasing chloride content. Above the CPT, E {sub pit} and E {sub prot} decreased linearly with log[Cl{sup -}]. The addition of bromide ions to the solution shifted both E {sub pit} and E {sub prot} towards positive values. In 4% NaCl, E {sub pit} increased linearly with pH in the range 1-10. The combined effect of chloride ion concentration and pH on the morphology of the pits was examined by scanning electron microscopy (SEM) following potentiodynamic cycling anodic polarization.

  5. Fourteen-year survival of Pseudomonas cepacia in a salts solution preserved with benzalkonium chloride.

    Science.gov (United States)

    Geftic, S G; Heymann, H; Adair, F W

    1979-01-01

    A strain of Pseudomonas cepacia that survived for 14 years (1963 to 1977) as a contaminant in an inorganic salt solution which contained commercial 0.05% benzalkonium chloride (CBC) as an antimicrobial preservative, was compared to a recent clinical isolate of P. cepacia. Ammonium acetate was present in the concentrated stock CBC solution, and served as a carbon and nitrogen source for growth when carried over into the salts solution with the CBC. The isolate's resistance to pure benzalkonium chloride was increased step-wise to a concentration of 16%. Plate counts showed 4 x 10(3) colony-forming units per ml in the salts solution. Comparison of growth rates, mouse virulence, antibiotics resistance spectra, and substrate requirements disclosed no differences between the contaminant and a recently isolated clinical strain of P. cepacia. The results indicate that it is critical that pharmaceutical solutions containing benzalkonium chloride as an antimicrobial preservative be formulated without extraneous carbon and nitrogen sources or be preserved with additional antimicrobial agents. PMID:453827

  6. Interaction between sulfate and chloride solution attack of concretes with and without fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Jin Zuquan; Sun Wei; Zhang Yunsheng; Jiang Jinyang; Lai Jianzhong [Qingdao Technological University, Qingdao (China). Department of Civil Engineering

    2007-08-15

    Two sets of concretes under attack of erosion solution of sulfate and chloride salt were investigated. One set was plain concrete without fly ash addition the other set is the concrete with 20% and 30% of fly ash addition. The corrosion solution includes three types: 3.5% NaCl, 5% Na{sub 2}SO{sub 4}, and a composite solution of 3.5% NaCl and 5% Na{sub 2}SO{sub 4}. Two corrosion regimes were employed in this study: naturally immersion. The experimental results showed that a presence of sulfate in the composite solution increased the resistance to chloride ingress into concretes at early exposure period, but the opposite was observed at latter exposure period. A presence of chloride in the composite solution reduces the damage of concrete caused by sulfate. Addition of fly ash may significantly improve the resistance to chloride ingress into concretes and the resistance to sulfate erosion when a suitable amount of fly ash addition and low water-to-binder (W/B) was employed. Studies of the different corrosion regimes indicate that concretes stored in corrosion solution for about 850 days, the changes in relatively dynamic modulus of elastically (RDME) could be described by three stages: linearly increasing period, steady period, and declining period. For drying-immersion cycles, an accelerated trend could be found. The changes in RDME included an accelerated decreased stage, linearly increased stage, and then a slowly decreased stage, finally accelerating failure stage. The mechanism was also investigated by the modern microanalysis techniques.

  7. Effect of Organic Inhibitors on Chloride Corrosion of Steel Rebars in Alkaline Pore Solution

    Directory of Open Access Journals (Sweden)

    Marina Cabrini

    2015-01-01

    Full Text Available The inhibition properties of aspartic and lactic acid salts are compared with nitrite ions with regard to their effect on critical chloride concentration. The tests were carried out on carbon steel specimens in simulated pore solutions with initial pH in the range of 12.6 to 13.8. The critical chloride concentrations were estimated through multiple specimen potentiostatic tests at potentials in the usual range for passive rebar in noncarbonated concrete structures. During tests, chloride ions were progressively added until all specimens showed localized attack, obtaining cumulative distribution curves reporting the fraction of corroded specimens as a function of chloride concentration. The presence of the organic inhibitors on the passivity film was detected by IR spectra. The results confirm that 0.1 M aspartate exhibits an inhibiting effect comparable with nitrite ions of the same concentration. Calcium lactate does not increase critical chloride concentration; however it appears to promote the formation of a massive scale, reducing the corrosion propagation.

  8. Passivation and pitting corrosion of. alpha. -brass (Cu/Zn: 63/37) in neutral buffer solutions containing chloride ions

    Energy Technology Data Exchange (ETDEWEB)

    Abd El-Rahman, H.A. (Cairo Univ., Gizeh (Egypt). Chemistry Dept.)

    1990-11-01

    The passivation behaviour and pitting corrosion of a commercial grade {alpha}-brass (Cu/Zn: 63/37) in neutral buffer solutions (borate and phosphate) in the presence and absence of chloride ions were investigated by electrochemical techniques. The results indicated the dezincification in absence of chloride ions at highly enough anodic potentials and both dezincification and pitting corrosion in the presence of chloride ions. The pitting susceptibility was found to depend on the composition of the buffer solution, chloride ion concentration and nature of the passive layer on the metal surface before pitting. Current transients corresponding to passivity, dezincification and pitting corrosion were identified and analyzed. (orig.).

  9. A Model Approach for Finding Cleaning Solutions for Plasticized Poly(Vinyl Chloride) Surfaces of Collections Objects

    DEFF Research Database (Denmark)

    Sanz Landaluze, Jon; Egsgaard, Helge; Morales Munoz, Clara

    2014-01-01

    solutions for the plasticized poly(vinyl chloride) used in the study was found. In addition, a specific method to tailor cleaning mixtures for plasticized poly(vinyl chloride) objects was developed by means of Hildebrand solubility parameters and the formulation of a Plasticizer Index calculated......This study focused on developing a surface cleaning treatment for one type of commercially available plasticized poly(vinyl chloride). The effects of cleaning solutions on samples of plasticized poly(vinyl chloride) were examined by several methods. The sample surface, prior to and after artificial...

  10. Electrochemical Behavior of Nano-grained Pure Copper in Dilute Alkaline Solution with Chloride Ion Trace

    Science.gov (United States)

    Fattah-Alhosseini, Arash; Imantalab, Omid; Attarzadeh, Farid Reza

    2016-10-01

    Effect of nano-grained structure on the interface behavior of pure copper in 0.01M KOH solution with chloride ion trace is investigated by various electrochemical techniques. Nano-grained structure was achieved by accumulative roll bonding (ARB) technique. Before any electrochemical measurements, microstructure was evaluated by means of optical microscopy and transmission electron microscopy (TEM). TEM observations showed that nano-grains (with an average size of below 100 nm) appeared after eight passes of ARB. Polarization curves revealed that increasing chloride ion concentration leads to a decrease in the corrosion and pitting potentials of both annealed and nano-grained pure copper samples. Electrochemical impedance spectroscopy revealed that chloride ion trace lowers passive film resistance and charge-transfer resistance in both annealed and nano-grained samples. Mott-Schottky analysis showed that the surface films formed on annealed and nano-grained samples in KOH solution with and without NaCl addition are of p-type semiconducting behavior. Moreover, this analysis showed that the acceptor density increases by increasing chloride ion concentration.

  11. Kinetics of Rare Earth Extraction from Baotou Bastnaesite in Hydrochloric Acid and Aluminum Chloride

    Science.gov (United States)

    Zhang, Xiao-Wei; Li, Mei; Liu, Zhao-Gang; Hu, Yan-Hong; Wang, Mi-Tang

    2017-06-01

    In this paper, the leaching kinetics of rare earth from Baotou bastnaesite in a HCl-AlCl3 solution was investigated. In addition, the effects of the HCl and AlCl3 concentrations, liquid to solid ratio, stirring speed, temperature, and time spent on the rare earth extraction were determined. The results indicated that the extraction was nearly independent of the stirring speed when it did not exceed 300 rpm, and the rate of leaching increased with increases in the HCl and AlCl3 concentrations, liquid to solid ratio, temperature, and time. The optimum dissolution conditions were determined under five experimental conditions. After leaching occurred, the progressive dissolution of the bastnaesite phase could be determined. The leaching kinetics was analyzed with a new variant of the shrinking core model in which both the interfacial transfer and diffusion across the product layer affected the rare earth extraction. The apparent activation energy was 35.57 kJ/mol, and the Arrhenius constant was 341.58 min-1. An empirical equation was derived to describe the extraction process of rare earth minerals.

  12. Resistance of Pseudomonas to Quaternary Ammonium Compounds. I. Growth in Benzalkonium Chloride Solution

    Science.gov (United States)

    Adair, Frank W.; Geftic, Sam G.; Gelzer, Justus

    1969-01-01

    Resistant cells of Pseudomonas aeruginosa and a waterborne Pseudomonas sp. (strain Z-R) were able to multiply in nitrogen-free minimal salts solution containing various concentrations of commercially prepared, ammonium acetate-buffered benzalkonium chloride (CBC), a potent antimicrobial agent. As the CBC concentration increased, growth increased until a point was reached at which the extent of growth leveled off or was completely depressed. Minimal salts solutions of pure benzalkonium chloride (PBC) containing no ammonium acetate did not support bacterial growth. When ammonium acetate was added to PBC solutions in the same concentrations found in CBC solutions, growth patterns developed that were comparable to those found with CBC. Likewise, (NH4)2SO4 added to PBC solutions supported growth of both organisms. P. aeruginosa was initially resistant to CBC levels of 0.02% and it was adapted to tolerate levels as high as 0.36%. Strain Z-R was naturally resistant to 0.4% CBC. Since ammonium acetate, carried over by the CBC used in drug formulations and disinfectant solutions, has the potential to support the growth of resistant bacteria and thus make possible the risk of serious infection, it is suggested that regulations allowing the presence of ammonium acetate in CBC solution be reconsidered. PMID:4984761

  13. Direct hydride derivatization of methyl- and ethylmercury chlorides in aqueous solution with KBH4

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A convenient hydride derivatization procedure of methyl-and ethylmercury chlorides to volatile hydrides was reported. In sealed vials methylmercury and ethylmercury compounds in acidic aqueous solutions were converted into their volatile forms by the reaction with potassium tetrahydroborate(KBH4) and elvolved to the headspace of the vials. The gaseous analytes in the headspace were extracted and concentrated by solid phase microextraction(SPME) and injected into gas chromatography (GC) for separation and identified by mass selective detector(MS).

  14. Chloride transport and its sensitivities to different boundary conditions in reclaimed soil solutions filled with fly ash

    Institute of Scientific and Technical Information of China (English)

    Xiao-Yang CHEN; Jia-Ping YAN; Shi-Wen ZHANG

    2013-01-01

    Chloride ion transport in reclaimed soil solutions filled with fly ash (FA) was investigated by measuring the hydraulic parameters (i.e.water retention curves and hydraulic conductivity) of three substrates,namely GSL,GFA,and CFA.Similar simulations were carried out under certain weather conditions.The different boundary conditions of chloride transport were also discussed from FA texture,cover soil thickness,groundwater table level,and initial chloride concentration.Furthcrmore,the sensitivities of chloride ions to these effect factors were analyzed.The results show that the different top soil thickness and initial chloride concentration have no effect on salinity of topsoil solution in the monitoring points,but they can clearly change the chloride concentration of FA layers.The sensibilities from top soil thickness and initial chloride content are exceedingly weak to the salinity balance based on two dimensions of the time and concentration.While the different FA texture and groundwater table not only affect the salinity equilibrium process of the whole reclaimed soil profile,but also change its balance state.Generally,coarse FA particles and high groundwater table can defer the salinity balance process of the reclaimed soil solution,and they also increase the chloride concentration of FA layer solutions,and even topsoil ones.

  15. Copper electrodeposition from cuprous chloride solutions containing lead, zinc or iron ions

    Institute of Scientific and Technical Information of China (English)

    M. Tchoumou; M. Roynette Ehics

    2005-01-01

    Cuprous chloride hydrochloric acid solutions were electrolysed in a two compartments cell without agitation for copper extraction. It is found that the current density affects the colour and the size of copper deposits. During electrodeposition of copper from cuprous solution in the presence of various concentrations of lead, zinc or iron ions at different current densities, it is observed that lead is codeposited with copper by increasing current density.In all experiments, the current efficiency for the copper deposition reaction fluctuates between 88.50% and 95.50%.

  16. The evaporation of the water-sodium chlorides solution droplets on the heated substrate

    Science.gov (United States)

    Orlova, Evgenija; Kuznetsov, Geniy; Feoktistov, Dmitriy

    2014-08-01

    This work presents an experimental study of the evaporation of a sessile water- sodium chlorides solution drop to open atmosphere on the solid substrate (anodized aluminum) under the varying heat flux. The main parameters defining drop profile were obtained: contact diameter, contact angle, height of the drop. The specific evaporation rate was calculated. The influence of the initial concentration of the evaporated solution to a value of the specific evaporation rate has been found out. The specific evaporation rate decreases with increasing of the concentration.

  17. Photochemical oxidation of chloride ion by ozone in acid aqueous solution.

    Science.gov (United States)

    Levanov, Alexander V; Isaykina, Oksana Ya; Amirova, Nazrin K; Antipenko, Ewald E; Lunin, Valerii V

    2015-11-01

    The experimental investigation of chloride ion oxidation under the action of ozone and ultraviolet radiation with wavelength 254 nm in the bulk of acid aqueous solution at pH 0-2 has been performed. Processes of chloride oxidation in these conditions are the same as the chemical reactions in the system O3 - OH - Cl(-)(aq). Despite its importance in the environment and for ozone-based water treatment, this reaction system has not been previously investigated in the bulk solution. The end products are chlorate ion ClO3(-) and molecular chlorine Cl2. The ions of trivalent iron have been shown to be catalysts of Cl(-) oxidation. The dependencies of the products formation rates on the concentrations of O3 and H(+) have been studied. The chemical mechanism of Cl(-) oxidation and Cl2 emission and ClO3(-) formation has been proposed. According to the mechanism, the dominant primary process of chloride oxidation represents the complex interaction with hydroxyl radical OH with the formation of Cl2(-) anion-radical intermediate. OH radical is generated on ozone photolysis in aqueous solution. The key subsequent processes are the reactions Cl2(-) + O3 → ClO + O2 + Cl(-) and ClO + H2O2 → HOCl + HO2. Until the present time, they have not been taken into consideration on mechanistic description and modelling of Cl(-) oxidation. The final products are formed via the reactions 2ClO → Cl2O2, Cl2O2 + H2O → 2H(+) + Cl(-) + ClO3(-) and HOCl + H(+) + Cl(-) ⇄ H2O + Cl2. Some portion of chloride is oxidized directly by O3 molecule with the formation of molecular chlorine in the end.

  18. Corrosion Behavior of Alloy 22 in Oxalic Acid and Sodium Chloride Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Day, S D; Whalen, M T; King, K J; Hust, G A; Wong, L L; Estill, J C; Rebak, R B

    2003-06-24

    Nickel based Alloy 22 (NO6022) is extensively used in aggressive industrial applications, especially due to its resistance to localized corrosion and stress corrosion cracking in high chloride environments. The purpose of this work was to characterize the anodic behavior of Alloy 22 in oxalic acid solution and to compare its behavior to sodium chloride (NaCl) solutions. Standard electrochemical tests such as polarization resistance and cyclic polarization were used. Results show that the corrosion rate of Alloy 22 in oxalic acid solutions increased rapidly as the temperature and the acid concentration increased. Extrapolation studies show that even at a concentration of 10{sup -4}M oxalic acid, the corrosion rate of Alloy 22 would be higher in oxalic acid than in 1 M NaCl solution. Alloy 22 was not susceptible to localized corrosion in oxalic acid solutions. Cyclic polarization tests in 1 M NaCl showed that Alloy 22 was susceptible to crevice corrosion at 90 C but was not susceptible at 60 C.

  19. New Mid-IR Lasers Based on Rare-Earth-Doped Sulfide and Chloride Materials

    Energy Technology Data Exchange (ETDEWEB)

    Nostrand, M

    2000-09-01

    Applications in remote-sensing and military countermeasures have driven a need for compact, solid-state mid-IR lasers. Due to multi-phonon quenching, non-traditional hosts are needed to extend current solid-state, room-temperature lasing capabilities beyond {approx} 4 {micro}m. Traditional oxide and fluoride hosts have effective phonon energies in the neighborhood of 1000 cm{sup -1} and 500 cm{sup -1}, respectively. These phonons can effectively quench radiation above 2 and 4 {micro}m, respectively. Materials with lower effective phonon energies such as sulfides and chlorides are the logical candidates for mid-IR (4-10 {micro}m) operation. In this report, laser action is demonstrated in two such hosts, CaGa{sub 2}S{sub 4} and KPb{sub 2}Cl{sub 5}. The CaGa{sub 2}S{sub 4}:Dy{sup 3+} laser operating at 4.3 {micro}m represents the first sulfide laser operating beyond 2 {micro}m. The KPb{sub 2}Cl{sub 5}:Dy{sup 3+} laser operating at 2.4 {micro}m represents the first operation of a chloride-host laser in ambient conditions. Laser action is also reported for CaGa{sub 2}S{sub 4}:Dy{sup 3+} at 2.4 {micro}m, CaGa{sub 2}S{sub 4}:Dy{sup 3+} at 1.4 {micro}m, and KPb{sub 2}Cl{sub 5}:Nd{sup 3+} at 1.06 {micro}m. Both host materials have been fully characterized, including lifetimes, absorption and emission cross sections, radiative branching ratios, and radiative quantum efficiencies. Radiative branching ratios and radiative quantum efficiencies have been determined both by the Judd-Ofelt method (which is based on absorption measurements), and by a novel method described herein which is based on emission measurements. Modeling has been performed to predict laser performance, and a new method to determine emission cross section from slope efficiency and threshold data is developed. With the introduction and laser demonstration of rare-earth-doped CaGa{sub 2}S{sub 4} and KPb{sub 2}Cl{sub 5}, direct generation of mid-IR laser radiation in a solid-state host has been demonstrated. In

  20. Erythrocyte lysis in isotonic solution of ammonium chloride: theoretical modeling and experimental verification.

    Science.gov (United States)

    Chernyshev, Andrey V; Tarasov, Peter A; Semianov, Konstantin A; Nekrasov, Vyacheslav M; Hoekstra, Alfons G; Maltsev, Valeri P

    2008-03-07

    A mathematical model of erythrocyte lysis in isotonic solution of ammonium chloride is presented in frames of a statistical approach. The model is used to evaluate several parameters of mature erythrocytes (volume, surface area, hemoglobin concentration, number of anionic exchangers on membrane, elasticity and critical tension of membrane) through their sphering and lysis measured by a scanning flow cytometer (SFC). SFC allows measuring the light-scattering pattern (indicatrix) of an individual cell over the angular range from 10 degrees to 60 degrees . Comparison of the experimentally measured and theoretically calculated light scattering patterns allows discrimination of spherical from non-spherical erythrocytes and evaluation of volume and hemoglobin concentration for individual spherical cells. Three different processes were applied for erythrocytes sphering: (1) colloid osmotic lysis in isotonic solution of ammonium chloride, (2) isovolumetric sphering in the presence of sodium dodecyl sulphate and albumin in neutrally buffered isotonic saline, and (3) osmotic fragility test in hypotonic media. For the hemolysis in ammonium chloride, the evolution of distributions of sphered erythrocytes on volume and hemoglobin content was monitored in real-time experiments. The analysis of experimental data was performed in the context of a statistical approach, taking into account that parameters of erythrocytes vary from cell to cell.

  1. Analysis of Frozen Sulfate and Chloride Salt Solutions Using Laser-induced Breakdown Spectroscopy Under Martian Conditions

    Science.gov (United States)

    Schröder, S.; Pavlov, S. G.; Hübers, H.-W.; Rauschenbach, I.; Jessberger, E. K.

    2010-03-01

    We showed the feasibility of laser-induced breakdown spectroscopy to analyze different frozen salt solutions under martian conditions. We focused on chloride and sulphate salts which were found on Mars and could lower the freezing point of water.

  2. Removal of sodium and chloride ions from aqueous solutions using fique fibers (Furcraea spp.).

    Science.gov (United States)

    Agudelo, Nikolay; Hinestroza, Juan P; Husserl, Johana

    2016-01-01

    Fique fibers obtained from the leaves of Furcraea spp., a highly abundant plant in the mountains of South America, may offer an alternative as biosorbents in desalination processes as they exhibit high removal capacities (13.26 meq/g for chloride ions and 15.52 meq/g for sodium ions) up to four times higher than exchange capacities commonly observed in synthetic resins. The ion removal capacity of the fibers was also found to be a function of the pH of the solution with the maximum removal of ions obtained at pH 8. Unlike most commercial ion exchange resins, our results suggest that fique fibers allow simultaneous removal of chloride and sodium ions.

  3. Studies on the electrodeposition of tin from acidic chloride-gluconate solutions

    Science.gov (United States)

    Rudnik, Ewa; Włoch, Grzegorz

    2013-01-01

    Electrodeposition of tin from acidic chloride-gluconate baths was investigated. Equilibrium distribution of tin(II) species showed domination of Sn(II)-gluconate complexes, but for Sn2+ concentrations 50 mM or higher increased percentage of Sn(II)-chloride complexes was found. Cyclic voltammetry, anodic stripping analysis and potentiostatic measurements indicated that rate of the cathodic process is determined by the release of metal cations from gluconate complexes in diluted bath (5 mM), but for more concentrated solutions reduction of Sn(II) ions run under diffusion control. Studies of anodic response showed that it depends on the Sn(II)/Glu ratio in the bath and deposition potential due to development of different planes of metal crystal. Average effective diffusion coefficients of metal species were determined. Morphology and structure tin deposits were also presented.

  4. INDIGO-DataCloud solutions for Earth Sciences

    Science.gov (United States)

    Aguilar Gómez, Fernando; de Lucas, Jesús Marco; Fiore, Sandro; Monna, Stephen; Chen, Yin

    2017-04-01

    INDIGO-DataCloud (https://www.indigo-datacloud.eu/) is a European Commission funded project aiming to develop a data and computing platform targeting scientific communities, deployable on multiple hardware and provisioned over hybrid (private or public) e-infrastructures. The development of INDIGO solutions covers the different layers in cloud computing (IaaS, PaaS, SaaS), and provides tools to exploit resources like HPC or GPGPUs. INDIGO is oriented to support European Scientific research communities, that are well represented in the project. Twelve different Case Studies have been analyzed in detail from different fields: Biological & Medical sciences, Social sciences & Humanities, Environmental and Earth sciences and Physics & Astrophysics. INDIGO-DataCloud provides solutions to emerging challenges in Earth Science like: -Enabling an easy deployment of community services at different cloud sites. Many Earth Science research infrastructures often involve distributed observation stations across countries, and also have distributed data centers to support the corresponding data acquisition and curation. There is a need to easily deploy new data center services while the research infrastructure continuous spans. As an example: LifeWatch (ESFRI, Ecosystems and Biodiversity) uses INDIGO solutions to manage the deployment of services to perform complex hydrodynamics and water quality modelling over a Cloud Computing environment, predicting algae blooms, using the Docker technology: TOSCA requirement description, Docker repository, Orchestrator for deployment, AAI (AuthN, AuthZ) and OneData (Distributed Storage System). -Supporting Big Data Analysis. Nowadays, many Earth Science research communities produce large amounts of data and and are challenged by the difficulties of processing and analysing it. A climate models intercomparison data analysis case study for the European Network for Earth System Modelling (ENES) community has been setup, based on the Ophidia big

  5. Compatibility and stability of potassium chloride and magnesium sulfate in 0.9% sodium chloride injection and 5% dextrose injeciton solutions.

    Science.gov (United States)

    Quay, I; Tan, E

    2001-01-01

    The compatibility and stability of 80 mmol/L potassium chloride and 16 mmol/L magnesium sulfate in 0.9% sodium chloride injection and in 5% dextrose injection solutions at 22 deg C have been studied by means of a Beckman Clinical Chemistry Analyzer Synchron CX5 Delta. The infusions were stable for 24 hours at 22 deg C. The results from both diluents showed an average of +/-5% fluctuations in concentration. None of the samples appeared to form visible precipitation or to change in color or clarity.

  6. Effect of Ammonium Chloride Solution on the Growth of Phosphorus Gypsum Whisker and Its Modification

    Directory of Open Access Journals (Sweden)

    Shouwei Jian

    2016-01-01

    Full Text Available Phosphogypsum is the by-product of phosphate of fertilizer or phosphate which causes serious environmental pollution. In this work, a series of phosphogypsum whiskers were prepared using phosphogypsum as raw materials and NH4Cl as additive through the atmospheric water solution method. The results showed that the ammonium chloride solution has a great influence on phosphogypsum whiskers growth and the solubility. The best whisker aspect ratio of phosphogypsum was preferred in 1 mol/L NH4Cl solution, in which the solubility achieved 6.434 mg/mL and the aspect ratio reached 69.29. Besides, NH4Cl was found to have a modified effect on gypsum whiskers’ growth and it can be used to get mesh or dendritic whiskers.

  7. Comparative absorption of calcium from carbonate tablets, lactogluconate/carbonate effervescent tablet, and chloride solution.

    Science.gov (United States)

    Ekman, M; Reizenstein, P; Teigen, S W; Rønneberg, R

    1991-01-01

    Intestinal absorption of calcium from three different labelled calcium preparations (all containing 500 mg elemental calcium) was determined using the whole body retention and urinary excretion of 47Ca in 14 normal subjects. Chewable calcium carbonate tablets showed a significantly (p less than 0.05) better mean minimum absorption of calcium (25.6% in exp. I, 22.8% in exp. II) than calcium given in the form of a lactogluconate/carbonate effervescent tablet, (17%), but similar to calcium in a chloride solution (24.7%). The minimum calcium absorption varied from 85 to 128 mg. All the preparations were taken with standardized low calcium test meals.

  8. A Study of Substituted Aliphatic Sulphides on the Corrosion Behaviour of Zinc in Ammonium Chloride Solution

    Directory of Open Access Journals (Sweden)

    R. Venckatesh

    2007-01-01

    Full Text Available Sulphur containing organic compounds decreases the corrosion rate by increasing the hydrogen over potential on zinc metal due to their electron donating groups. Their inhibiting effect was found to be associated with their adsorption on the active centers of the metal. The inhibition efficiencies of some aliphatic sulphides in ammonium chloride solution have been studied by weight loss studies, polarization and impedance measurements. The effect of substituent groups is correlated with their inhibition performance. These studies due to their relevance in Zn-Manganese dry batteries assume their importance.

  9. Comparison of Inactivation and Unfolding of Calf Intestinal Alkaline Phosphatase in Guanidinium Chloride Solution

    Institute of Scientific and Technical Information of China (English)

    张英侠; 闫淑莲; 刘永利; 席宏伟; 周海梦

    2002-01-01

    The changes in activity and unfolding of calf intestinal alkaline phosphatase (CIP) during denaturation in guanidinium chloride solutions of different concentrations were investigated using ultraviolet difference absorption spectra and fluorescence emission spectra. Unfolding and inactivation rate constants were measured and compared. The inactivation course is much faster than that of unfolding, which suggests that the active site of CIP containing two zinc ions and one magnesium ion is situated in a limited and flexible region of the enzyme molecule, which is more fragile to the denaturant than the protein as a whole.

  10. Simultaneous spectrophotometric determination of thorium and rare earth metals with m-carboxychlorophosphonazo (CPAmK) and cetylpyridinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Chunggin Hsu; Ximan Lian; Jiaomai Pan (East China Normal Univ., Shanghai, SH (China))

    1991-09-01

    Th and rare earth elements (REE) react with m-carboxychlorophosphonazo (CPAmK) in the absence of cetylpyridinium chloride (CPC) to form colour complexes. In the presence of CPC, REE-complexes are not formed because of micellar masking, while Th gives a more sensitive reaction with CPAmK. Most of the foreign ions are tolerated in considerable amounts; 360-1000-fold amounts of rare earths do not interfere with the determination of Th. The optimum conditions of the complex-formation reactions and the compositions of Th-CPAmK complexes are described. A simple method is proposed for simultaneous determination of Th and rare earths without previous separation. (author).

  11. Corrosion inhibitors in concrete. Part II: Effect on chloride threshold values for corrosion of steel in synthetic pore solutions

    Energy Technology Data Exchange (ETDEWEB)

    Mammoliti, L.; Hansson, C.M.; Hope, B.B.

    1999-10-01

    The effectiveness of four commercially available corrosion inhibitors for use in cement-based materials was assessed in synthetic concrete pore solution containing chlorides. The effect of the surface topography of the sample and the composition of the pore solution was also assessed. Although in a parallel study the inhibitors were observed to delay the onset of corrosion, in these tests in pore solution they were found to be ineffective in increasing the chloride threshold value of reinforcing steel exposed to chlorides and had little influence on the progression of corrosion once initiated. This suggests that chemical reactions within the cement phase are responsible for the observed results. Metallographically polished samples proved the most resistant to corrosion regardless of electrolyte composition and samples with all surface finishes exhibited lower resistance in solutions containing only calcium hydroxide than in the higher pH synthetic concrete pore solutions.

  12. Direct effect of chlorine dioxide, zinc chloride and chlorhexidine solution on the gaseous volatile sulfur compounds.

    Science.gov (United States)

    Kim, Ju-Sik; Park, Ji-Woon; Kim, Dae-Jung; Kim, Young-Ku; Lee, Jeong-Yun

    2014-11-01

    This study focused on the ability of aqueous anti-volatile-sulfur-compound (VSC) solutions to eliminate gaseous VSCs by direct contact in a sealed space to describe possible mode of action of anti-VSC agents. Twenty milliliters of each experimental solution, 0.16% sodium chlorite, 0.25% zinc chloride, 0.1% chlorhexidine and distilled water, was injected into a Teflon bag containing mixed VSCs, hydrogen sulfide, methyl mercaptan and dimethyl sulfide and mixed vigorously for 30 s. The VSC concentration was measured by gas chromatography before, immediately after, 30 min and 60 min after mixing. The sodium chlorite solution reduced the VSC concentration remarkably. After mixing, nearly all VSCs were eliminated immediately and no VSCs were detected at 30 and 60 min post-mixing. However, in the other solutions, the VSC concentration decreased by ∼30% immediately after mixing and there was no further decrease. The results suggest that sodium chlorite solution has the effect of eliminating gaseous VSCs directly. This must be because it can release chlorine dioxide gas which can react directly with gaseous VSCs. In the case of other solutions that have been proved to be effective to reduce halitosis clinically, it can be proposed that their anti-VSC effect is less likely due to the direct chemical elimination of gaseous VSCs in the mouth.

  13. Removal of potassium chloride by nanofiltration from ion-exchanged solution containing potassium clavulanate.

    Science.gov (United States)

    Kim, Hyun Han; Kim, Jae Hyung; Chang, Yong Keun

    2010-01-01

    In this study, nanofiltration with NF200 membrane was employed to remove KCl from ion-exchanged solutions containing potassium clavulanate. The pore radius of NF200 membrane was estimated to be around 0.39 nm. The effects of operating pressure on separation performance were investigated in a range of 100-400 psig. The influences of cross-flow velocity (0.14-0.70 cm/s), temperature (4-25 degrees C), and feed composition were also investigated. In all experiments, clavulanate rejection showed high levels from 0.91 to 0.99, while chloride rejection ranged from 0.06 to 0.54. In a case at an operating pressure of 50 psig and 25 degrees C, as much as 94% of clavulanate was retained while 94% of chloride was removed, indicating that NF200 membrane was a suitable choice for selectively removing KCl. NF200 membrane also showed a stable performance in the operational stability test with an ion-exchanged solution obtained by treating actual fermentation broth.

  14. Simultaneous leaching of Pt, Pd and Rh from automotive catalytic converters in chloride-containing solutions

    Science.gov (United States)

    Hasani, M.; Khodadadi, A.; Koleini, S. M. J.; Saeedi, A. H.; Meléndez, A. M.

    2017-01-01

    Dissolution of platinum group metals (PGM; herein Pt, Pd and Rh) in different chloride-based leaching systems from spent auto catalysts was performed. Response surface methodology and a five-level-five-factor central composite design were used to evaluate the effects of 1) temperature, 2) liquid-to-solid ratio, 3) stirring speed, 4) acid concentration and 5) particle size on extraction yield of PGM by aqua regia. Analysis of variance was used to determine the optimum conditions and most significant factors affecting the overall metal extraction. In the optimum conditions, leaching of Pt, Pd and Rh was 91.58%, 93.49% and 60.15%, respectively. The effect of different oxidizing agents on the PGM dissolution in chloride medium was studied comparatively in the following leaching systems: a) aqua regia/sulfuric acid mixture, b) hydrogen peroxide in sulfuric acid (piranha solution), c) sodium hypochlorite and d) copper(II). Dissolution of Rh is increased in both aqua regia and hydrogen peroxide/hydrochloric acid solutions by adding sulfuric acid.

  15. Extraction studies of cobalt (Ⅱ) and nickel (Ⅱ) from chloride solution using PC88A

    Institute of Scientific and Technical Information of China (English)

    LUO Lin; WEI Jian-hong; WU Gen-yi; F. TOYOHISA; S. ATSUSHI

    2006-01-01

    Solvent extraction study of cobalt and nickel were carried out from a chloride solution with a high ratio of Co to Ni using the sodium salt of PC88A as extractant diluted in kerosene. The solution was generated in batches by leaching a tungsten super alloy scraps. The results show that extraction rate of metal ions increases with increase of aqueous phase pH value. The pH0.5 value difference of 1.40 with PC88A indicates the possible separation of cobalt and nickel. Increase of the concentration of the solvent can enhance the percentage extraction of both metal ions. Improvement of temperature is beneficial to extraction separation of cobalt and nickel. Extraction and stripping processes were also studied in a cross-current solvent extraction unit and the results were also given.

  16. Effect of Sulfide Concentration on Copper Corrosion in Anoxic Chloride-Containing Solutions

    Science.gov (United States)

    Kong, Decheng; Dong, Chaofang; Xu, Aoni; Man, Cheng; He, Chang; Li, Xiaogang

    2017-02-01

    The structure and property of passive film on copper are strongly dependent on the sulfide concentration; based on this, a series of electrochemical methods were applied to investigate the effect of sulfide concentration on copper corrosion in anaerobic chloride-containing solutions. The cyclic voltammetry and x-ray photoelectron spectroscopy analysis demonstrated that the corrosion products formed on copper in anaerobic sulfide solutions comprise Cu2S and CuS. And the corrosion resistance of copper decreased with increasing sulfide concentration and faster sulfide addition, owing to the various structures of the passive films observed by the atomic force microscope and scanning electron microscope. A p-type semiconductor character was obtained under all experimental conditions, and the defect concentration, which had a magnitude of 1022-1023 cm-3, increased with increasing sulfide concentration, resulting in a higher rate of both film growth and dissolution.

  17. Mid-infrared spectroscopic analysis of saccharides in aqueous solutions with sodium chloride.

    Science.gov (United States)

    Kanou, Mikihito; Kameoka, Takaharu; Suehara, Ken-Ichiro; Hashimoto, Atsushi

    2017-04-01

    The infrared spectral characteristics of three different types of disaccharides (trehalose, maltose, and sucrose) and four different types of monosaccharides (glucose, mannose, galactose, and fructose) in aqueous solutions with sodium chloride (NaCl) were determined. The infrared spectra were obtained using the FT-IR/ATR method and the absorption intensities respected the interaction between the saccharide and water with NaCl were determined. This study also focused on not only the glycosidic linkage position and the constituent monosaccharides, but also the concentration of the saccharides and NaCl and found that they have a significant influence on the infrared spectroscopic characterization of the disaccharides in an aqueous solution with NaCl. The absorption intensities representing the interaction between a saccharide and water with NaCl were spectroscopically determined. Additionally, the applications of MIR spectroscopy to obtain information about saccharide-NaCl interactions in foods and biosystems were suggested.

  18. Conductivity and Viscosity Measurements for Binary Lysozyme Chloride Aqueous Solution and Ternary Lysozyme-Salt-Water Solution

    CERN Document Server

    Buzatu, D; Buzatu, F D

    2004-01-01

    We use the conductimetric method, adequate to electrolytes, to determine the lysozyme charge in lys-water and ternary lys-salt-water systems. We measured also the viscosities for the above binary and ternary systems in the same conditions at pH$=4.5$ and T$=298$ K, measurements that allow us to see any effect of viscosity on cations mobilities and implicitly on the lysozyme charge. The method is illustrated for the lysozyme chloride aqueous solution system at 25$^o$ C, using the data reported here for pH$=4.5$ at 0.15, 0.6, 0.8, 1., 1.5, 2., 2.5, 3., 3.5 mM (mg/mL) lysozyme chloride concentrations. The method was also applied to ternary lys-salt-water systems in the same conditions at pH$=4.5$ and T$=25^o$ C. Ternary conductivities are reported for a mean concentration 0.6 mM of lysozyme chloride in all systems and a mean concentration 0.01, 0.025, 0.05, 0.1, 0.175, 0.2, 0.5, 0.7, 0.9, 1.2, 1.3 and 1.4 M for NaCl; 0.005, 0.01, 0.05, 0.1, 0.175, 0.2, 0.5, 0.7, 0.9, 1.2, 1.3, 1.4 and 1.5 M for KCl; 0.005, 0.01,...

  19. Solid-phase extraction of cobalt(II) from lithium chloride solutions using a poly(vinyl chloride)-based polymer inclusion membrane with Aliquat 336 as the carrier.

    Science.gov (United States)

    Kagaya, Shigehiro; Cattrall, Robert W; Kolev, Spas D

    2011-01-01

    The extraction of cobalt(II) from solutions containing various concentrations of lithium chloride, hydrochloric acid, and mixtures of lithium chloride plus hydrochloric acid is reported using a poly(vinyl chloride) (PVC)-based polymer inclusion membrane (PIM) containing 40% (w/w) Aliquat 336 as a carrier. The extraction from lithium chloride solutions and mixtures with hydrochloric acid is shown to be more effective than extraction from hydrochloric acid solutions alone. The solution concentrations giving the highest amounts of extraction are 7 mol L(-1) for lithium chloride and 8 mol L(-1) lithium chloride plus 1 mol L(-1) hydrochloric acid for mixed solutions. Cobalt(II) is easily stripped from the membrane using deionized water. The cobalt(II) species extracted into the membrane are CoCl(4)(2-) for lithium chloride solutions and HCoCl(4)(-) for mixed solutions; these form ion-pairs with Aliquat 336. It is also shown that both lithium chloride and hydrochloric acid are extracted by the PIM and suppress the extraction of cobalt(II) by forming ion-pairs in the membrane (i.e. R(3)MeN(+)·HCl(2)(-) for hydrochloric acid and R(3)MeN(+)·LiCl(2)(-) for lithium chloride).

  20. The use of bis (-2-ethylhexyl) phosphoric acid for the extraction of zinc from concentrated ammonium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Amer, S.; Luis, A.; Cuadra, A. de la; Caravaca, C.

    1994-01-01

    The extraction of zinc from concentrated ammonium chloride solutions by means of the bis(-2-ethylhexyl) phosphoric acid is studied. Mass balances and chemical equilibria relating the different chemical species in both phases are presented in order to establish a model describing the behaviour of the different species. Good agreement between experimental data and theoretical curves is obtained. A comparison of the zinc extraction from a strong complexing medium as that of concentrated ammonium chloride solutions with an uncomplexing zinc perchlorate solution is made, in order to see the influence of the complexing effect of the aqueous phase on zinc extraction. (Author) 36 p.

  1. Leaching of lead from zinc leach residue in acidic calcium chloride aqueous solution

    Science.gov (United States)

    Wang, Le; Mu, Wen-ning; Shen, Hong-tao; Liu, Shao-ming; Zhai, Yu-chun

    2015-05-01

    A process with potentially reduced environmental impacts and occupational hazards of lead-bearing zinc plant residue was studied to achieve a higher recovery of lead via a cost-effective and environmentally friendly process. This paper describes an optimization study on the leaching of lead from zinc leach residue using acidic calcium chloride aqueous solution. Six main process conditions, i.e., the solution pH value, stirring rate, concentration of CaCl2 aqueous solution, liquid-to-solid (L/S) ratio, leaching temperature, and leaching time, were investigated. The microstructure and components of the residue and tailing were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). On the basis of experimental results, the optimum reaction conditions were determined to be a solution pH value of 1, a stirring rate of 500 r·min-1, a CaCl2 aqueous solution concentration of 400 g·L-1, a liquid-to-solid mass ratio of 7:1, a leaching temperature of 80°C, and a leaching time of 45 min. The leaching rate of lead under these conditions reached 93.79%, with an iron dissolution rate of 19.28%. Silica did not take part in the chemical reaction during the leaching process and was accumulated in the residue.

  2. Enhanced corrosion resistance of magnesium alloy AM60 by cerium(III) in chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Heakal, F. El-Taib, E-mail: fakihaheakal@yahoo.com [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt); Shehata, O.S. [Physical Chemistry Department, National Research Centre, Dokki, Giza (Egypt); Tantawy, N.S. [Girl' s College of Arts, Science and Education, Ain Shams University, Asma Fahmi Street, Cairo (Egypt)

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer Corrosion rate of AM60 in Cl{sup -} solution decreases with increasing [Ce{sup 3+}] up to 1 mM. Black-Right-Pointing-Pointer Beyond that level the corrosion rate increases and then stabilizes. Black-Right-Pointing-Pointer The spontaneously formed film characterises by increasing resistance with time. Black-Right-Pointing-Pointer The converted film after 10 d immersion exhibits self-healing in plain Cl{sup -} solution. Black-Right-Pointing-Pointer Ce(III) should be present in the corrodent to form a more compact surface coating. - Abstract: Cerium(III) was utilised to enhance the corrosion resistance of AM60 in NaCl solution. Ce{sup 3+} can suppress corrosion deterioration up to 1.0 mM. Beyond that level corrosion rate increases till a steady value. Surface film resistance increases with time evolution until 24 h, then decreases and stabilizes. The converted film after 240 h immersion exhibits self-healing and thickening when re-exposed to plain chloride solution. SEM and EDX confirmed that when Ce is present as additive in solution, more compact coating is formed better than its presence as a post coating on the alloy surface before being immersed in the corrosive environment.

  3. Alcohol solutions of triphenyl-tetrazolium chloride as high-dose radiochromic dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Kovacs, A.; Wojnarovits, L.; El-Assy, N.B.; Afeefy, H.Y.; Al-Sheikhly, M.; Walker, M.L.; McLaughlin, W.L. [National Inst. of Standards and Technology (NML), Gaithersburg, MD (United States). Ionizing Radiation Div.

    1995-10-01

    The radiolytic reduction of colorless tetrazolium salts in aqueous solution to the highly colored formazan dye is a well-known acid-forming radiation chemical reaction. Radiochromic thin films and three-dimensional hydrocolloid gels have been used for imaging and mapping absorbed dose distributions. The high solubility of 2,3,5-triphenyl-tetrazolium chloride (TTC) in alcohols provides a useful liquid dosimeter (45 mM TTC in aerated ethanol) and shows a linear response of absorbance increase ({lambda}{sub max} = 480 nm) with dose over the range 1-16 kGy. The linear molar absorption coefficient ({epsilon}{sub m}) for the formazan at the absorption peak is 1.5 x 10{sup 3} m{sup 2} mol{sup -1}, and the radiation chemical yield for the above solution is G (formazan) 0.014 {mu}mol J{sup -1}. The irradiation temperature coefficient is about 0.8 percent per degree Celsius rise in temperature over the temperature range 0-30 {sup o}C but is much larger between 30{sup o} and 60 {sup o}C. The unirradiated and irradiated solutions are stable over at least five days storage at normal laboratory temperature in the dark, but when stored in daylight at elevated temperature, the unirradiated solution in sealed amber glass ampoules undergoes slow photolytic dye formation, and the irradiated solution experiences initial fading and subsequent reversal (photochromism) when exposed to direct sunlight. (author).

  4. Rheological characterization of solutions and thin films made from amylose-hexadecylammonium chloride inclusion complexes and polyvinyl alcohol

    Science.gov (United States)

    The rheological properties of aqueous solutions and films made from blends of polyvinyl alcohol (PVOH) and amylose-hexadecylammonium chloride inclusion complexes (Hex-Am) were investigated to better understand the polymer interactions and processing parameters. Aqueous solutions of Hex-Am displayed ...

  5. [The influence of an isotonic solution containing benzalkonium chloride and a hypertonic seawater solution on the function of ciliary epithelium from the nasal cavity in vitro].

    Science.gov (United States)

    Laberko, E L; Bogomil'sky, M R; Soldatsky, Yu L; Pogosova, I E

    2016-01-01

    The objective of the present study was to evaluate the influence of an isotonic saline solution containing benzalconium chloride and of a hypertonic seawater solution on the function of ciliary epithelium in the nasal cavity in vitro. To this effect, we investigated the cytological material obtained from 35 children presenting with adenoid tissue hypertrophy. The tissue samples were taken from the nasal cavity by the standard method. A cellular biopsy obtained from each patient was distributed between three tubes that contained isotonic saline solution supplemented by benzalconium chloride (0.1 mg/ml), a hypertonic seawater solution, and a standard physiological saline solution. It was shown that the number of the viable cells in both isotonic solutions was statistically comparable and significantly higher than in the hypertonic solution (p<0.05). The ciliary beat frequency of the cells embedded in the two isotonic solutions was not significantly different but considerably exceeded that in the hypertonic seawater solution (p<0.05). Thus, the present study has demonstrated the absence of the ciliotoxic influence of isotonic saline solution containing benzalconium chloride at a concentration of 0.1 mg/ml and the strong ciliotoxic effect of the hypertonic seawater solution. This finding gives reason to recommend isotonic solutions for the regular application whereas hypertonic solutions can be prescribed only during infectious and/or inflammatory ENT diseases.

  6. Influence of flexural fatigue on chloride threshold value for the corrosion of steels in Ca(OH){sub 2} solutions

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Linhua, E-mail: hhulhjiang@gmail.com [College of Mechanics and Materials, Hohai University, 1 Xikang Rd., Nanjing, 210098 (China); Hydraulic Engineering Research Center for New Materials and Protection, Jiangsu Province, 1 Xikang Rd., Nanjing, 210098 (China); Liu, Hao; Wang, Yongliang; Zhang, Yan; Song, Zijian; Xu, Jinxia; Jin, Ming; Jiang, Peng; Xu, Yi; Gao, Hailang [College of Mechanics and Materials, Hohai University, 1 Xikang Rd., Nanjing, 210098 (China)

    2015-08-15

    The flexural fatigue was enforced on reinforced concrete beam with stress level of 0.6 and different fatigue life cycles. Steels removed from the beams were soaked in the saturated Ca(OH){sub 2} solution, which was used as a simulated concrete pore solution. The NaCl solution was chosen as the source of chloride ions. The Chloride Threshold Values (CTV) were detected by combining the open-circuit potentials (E{sub corr}) with the corrosion current densities (i{sub corr}), which were obtained by electrochemical impedance spectroscopy (EIS). The changes of microstructure caused by the flexural fatigue were observed by scanning electron microscopy (SEM). The results showed that as the fatigue cycle times increased, the CTV decreased under a certain stress level and range of fatigue life cycles. The grains became finer and cracks appeared on the surface of the steels. While the capacitive arcs under no flexural fatigue decreased gradually with the addition of chloride ions, the ones under flexural fatigue presented no regularity. Cracks at the surface were expanded because of sustaining flexural fatigue, which degenerated the later resistance to chloride ions of the steels. - Highlights: • The influence of flexural fatigue on chloride threshold value was examined. • The chloride threshold values vary with different fatigue life cycles. • The corrosion behavior depends on the surface integrity of the steels.

  7. Reentrant condensation of lysozyme: Implications for studying dynamics of lysozyme in aqueous solutions of lithium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Mamontov, Eugene [ORNL; O' Neill, Hugh Michael [ORNL

    2014-01-01

    Recent studies have outlined the use of eutectic solution of lithium chloride in water to study microscopic dynamics of lysozyme in an aqueous solvent that is remarkably similar to pure water in many respects, yet allows experiments over a wide temperature range without the solvent crystallization. The eutectic point in (H2O)R(LiCl) system corresponds to R 7.3, and it is of interest to investigate whether less concentrated aqueous solutions of LiCl could be employed in low-temperature studies of a solvated protein. We have investigated a range of concentrations of lysozyme and LiCl in aqueous solutions to identify systems that do not show phase separation and avoid solvent crystallization on cooling down. Compared to the lysozyme concentration in solution, the concentration of LiCl in the aqueous solvent plays the major role in determining systems suitable for low-temperature studies. We have observed interesting and rich phase behavior reminiscent of reentrant condensation of proteins.

  8. Crevice corrosion of nickel superalloy in deaerated chloride/sulphate solution at 90°C

    Science.gov (United States)

    Rincón Ortiz, M.; Carranza, R. M.; Rodríguez, M. A.

    2017-01-01

    Alloy 22 is a nickel base alloy highly resistant to all forms of corrosion. It was designed to resist to most aggressive environments for industrial applications. Electrochemical studies such as Potentiodynamic-Galvanostatic-Potentiostatic (PD-GS-PD) tests and Electrochemical Impedance Spectroscopy (EIS) and Scanning Electron Microscopy (SEM) observations were performed to determine the corrosion behaviour of alloy 22 (N06022). The effect of sulphate ion in chloride containing solutions at 90°C, were studied in this work under aggressive conditions where this material might be susceptible to crevice corrosion. The electrolyte solution, which consisted of 0.1M and 1M NaCl and different sulphate concentrations. It was observed that there were complete inhibitions of crevice corrosion for R crit =[SO4 =]/[Cl-]=1 in the 0.1mol/L NaCl solutions and R crit =2 in the 1mol/L NaCl solutions. The corrosion rate obtained was about 0.1μm/year at 24 hours of immersion.

  9. Interfacial behavior of perchlorate versus chloride ions in saturated aqueous salt solutions

    Energy Technology Data Exchange (ETDEWEB)

    Ghosal, S; Kuo, I W; Baer, M D; Bluhm, H

    2009-04-14

    In recent years combination of theoretical and experimental work have presented a novel view of the aqueous interface wherein hard and/or multiply charged ions are excluded from the interface, but large polarizable anions show interfacial enhancement relative to the bulk. The observed trend in the propensity of anions to adsorb at the air/water interface appears to be reverse of the Hofmeister series for anions. This study focuses on experimental and theoretical examination of the partitioning behavior of perchlorate (ClO{sub 4}{sup -}) and chloride (Cl{sup -}) ions at the air/water interface. We have used ambient pressure X-ray photoelectron spectroscopy technique to directly probe the interfacial concentrations of ClO{sub 4}{sup -} and Cl{sup -} ions in sodium perchlorate and sodium chloride solutions, respectively. Experimental observations are compared with first principles molecular dynamics simulations. Both experimental and simulation results show enhancement of ClO{sub 4}{sup -} ion at the interface, compared with the absence of such enhancement in the case of Cl{sup -} ion. These observations are in agreement with the expected trend in the interfacial propensity of anions based on the Hofmeister series.

  10. Leaching platinum-group metals in a sulfuric acid/chloride solution

    Science.gov (United States)

    Mahmoud, M. H. H.

    2003-04-01

    A leaching process was established based on the ability of platinum-group metals to form stable chloro-complexes in acidic chloride solutions. Industrial catalyst losses were examined for the recovery of platinum, palladium, and rhodium by leaching with a mixture of sulfuric acid and sodium chloride to avoid using aqua regia or autoclave conditions. Extraction of platinum and rhodium in 60% H2SO4 at 135°C steadily increased with increasing NaCl concentrations reaching 95% and 85%, respectively, at 0.1 M NaCl after two hours. By comparison, palladium was dissolved more quickly but also reached 85% under the same conditions. Extraction of each metal increased with temperatures up to 125°C but plateaued at higher temperatures. Similar behavior was observed with increasing H2SO4 concentrations up to 60%. More than 99% extraction of each metal was obtained after ten hours using 0.1 M NaCl and 60% H2SO4 at 125°C.

  11. Protection of copper surface with phytic acid against corrosion in chloride solution.

    Science.gov (United States)

    Peca, Dunja; Pihlar, Boris; Ingrid, Milošev

    2014-01-01

    Phytic acid (inositol hexaphosphate) was tested as a corrosion inhibitor for copper in 3% sodium chloride. Phytic acid is a natural compound derived from plants, it is not toxic and can be considered as a green inhibitor. Electrochemical methods of linear polarization and potentiodynamic polarization were used to study the electrochemical behaviour and evaluate the inhibition effectiveness. To obtain the optimal corrosion protection the following experimental conditions were investigated: effect of surface pre-treatment (abrasion and three procedures of surface roughening), pre-formation of the layer of phytic acid, time of immersion and concentration of phytic acid. To evaluate the surface pre-treatment procedures the surface roughness and contact angle were measured. Optimal conditions for formation of phytic layer were selected resulting in the inhibition effectiveness of nearly 80%. Morphology and composition of the layer were further studied by scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. The layer of phytic acid with thickness in the nanometer range homogeneously covers the copper surface. The obtained results show that this natural compound can be used as a mildly effective corrosion inhibitor for copper in chloride solution.

  12. EVOLUTION OF THE ELECTROCHEMICAL CHARACTERISTICS DURING PITTING CORROSION OF PURE ALUMINUM IN SODIUM CHLORIDE SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Z. Zhang; C. Cai; F.H. Cao; Z.N. Gao; J.Q. Zhang; C.N. Cao

    2005-01-01

    The corrosion behavior of pure aluminum in neutral 3.0% (mass fraction) sodium chloride (NaCl) solution has been studied using electrochemical impedance spectroscopy (ELS) measurement in conjunction with the scanning electron microscopy (SEM) technique. EIS information on the evolution of pitting corrosion over a period of 15 days has been obtained and analyzed with equivalent circuit technique. The results shown that, during the ensemble constant immersion time, two time constants involved, the high frequency one originated from the protective layer on the corroding surface while the low frequency one from the diffusion process or the corrosion reaction and so on. And there existed a period for oxide film to growth and thickening prior to the commencement of the attacking of chloride ions to the substrate. Meanwhile, good relationship between EIS and the material corrosion type/severity has been obtained, which has been interpreted according to the characteristics of corrosion process such as auto acceleration of pitting corrosion and the protection of local anodic reaction to the area around them.

  13. Growth and characterization of solution-grown tetra glycine barium chloride (TGBC) single crystals

    Science.gov (United States)

    Senthil Pandian, M.; Ramasamy, P.

    2008-05-01

    The single crystals of tetra glycine barium chloride (TGBC), a semi-organic material, were grown by the solvent evaporation technique from an aqueous solution of glycine and barium chloride at ambient temperature. Good optical quality single crystals of size 11×13×7 mm 3 were grown in a period of 2 weeks. Powder X-ray diffraction (XRD) and Fourier transform infrared transmission (FTIR) have confirmed the formation of the new crystal. The grown crystals were characterized by single-crystal XRD analysis to study the crystal structure. The crystalline perfection was evaluated by high-resolution X-ray diffractometry (HRXRD). From this analysis we found that the quality of the crystal was quite good. The full-width at half-maximum (FWHM) of the diffraction curves is 8.5 arcsec, which is very close to that expected from the plane wave dynamical theory of XRD showing that the crystalline perfection is excellent. UV-Vis-NIR spectrum was recorded to study the optical transparency of the grown crystals. Thermal properties of the crystal have been investigated using thermo gravimetric (TG), differential thermal analysis (DTA). The mechanical strength of the crystal is estimated by Vicker's hardness test.

  14. CORROSION MONITORING OF LY12 IN SODIUM CHLORIDE SOLUTION WITH ELECTROCHEMICAL NOISE TECHNIQUE

    Institute of Scientific and Technical Information of China (English)

    J.Q. Zhang; Z. Zhang; J.M. Wang; H.B. Shao; C.N. Cao

    2001-01-01

    Spontaneous electrochemical noise (EN) can be a rich source of information concerning the processes simultaneously occurring on a corroding interface. But the noise signal is often difficult to be analyzed due to the complicated nature of the specific systems being investigated. In this paper, the potential noise fluctuations during the free corrosion of commercial aluminum alloy LY12 in sodium chloride solution was recorded and analyzed with different techniques. The typical results showed that the fractal dimension (D,n) obtained from spectral power density (SPD) is mainly directly proportional to the intensity of pitting corrosion and to the value of pitting parameter (SE) derived from dimensional analysis, while the fractal dimension (DE) obtained from EIS is mainly related to the uniform corrosion.

  15. Effect of Initial Concentrations on Solidification of Ammonium Chloride water Solution

    Institute of Scientific and Technical Information of China (English)

    1992-01-01

    The effect of initial concentrations on solidification of ammonium chloride water solution is numerically investigated in detail.The solidifying process.with the cold wall temperature lower than the eutectic temperature,is assumed to be one-dimensional,and controlled by heat conduction only.The simulation reveals that:(1) The solid-mush interface grows in a linear manner,while the growth rate of the mush-liquid interface decreases in a parabolic manner,with increasing initial concentrations.(2) The temperature field in the whole region has parabolic characteristics,but is shows a linear feature in the solid zone and mushy zone.(3) The concentration always has linear characteristics in the much.(4)The solid fraction distribution is strongly affected by the initial concertration.The solidification process shows quite different features,especially at small and high initial concentrations.

  16. Analysis of corrosion behavior of LY12 in sodium chloride solution with wavelet transform technique

    Institute of Scientific and Technical Information of China (English)

    张昭; 曹发和; 程英亮; 张鉴清; 王建明; 曹楚南

    2002-01-01

    Wavelet transforms(WT) are proposed as an alternative tool to overcome the limitations of fast Fourier transforms(FFT) in the analysis of electrochemical noise(EN) data. The most relevant feature of this method of analysis is its capability of decomposing electrochemical noise records into different sets of wavelet coefficients(distinct type of events), which contains information about the time scale characteristic of the associated corrosion event. In this context, the potential noise fluctuations during the free corrosion of commercial aluminum alloy LY12 in sodium chloride solution was recorded and analyzed with wavelet transform technique. The typical results show that the EN signal is composed of distinct type of events, which can be classified according to their scales, i.e. their time constants. Meanwhile, the energy distribution plot(EDP) can be used as "fingerprints" of EN signals and can be very useful for analyzing EN data in the future.

  17. ELECTROCHEMICAL NOISE ANALYSIS OF PURE ALUMINUM IN SODIUM CHLORIDE SOLUTION WITH WAVELET TRANSFORM TECHNIQUE

    Institute of Scientific and Technical Information of China (English)

    Z. Zhang; Q.D. Zhong; J.Q. Zhang; Y.L. Cheng; F.H. Cao; J.M. Wang; C.N. Cao

    2002-01-01

    Wavelet transforms (WT) are proposed as an alternative tool to overcome the limita-tions of Fourier transforms (FFT) in the analysis of electrochemical noise (EN) data.The most relevant feature of this method of analysis is its capability of decomposingelectrochemical noise records into different sets of wavelet coefficients, which containinformation about the time scale characteristic of the associated corrosion event. Inthis context, the potential noise fluctuations during the free corrosion of pure alu-minum in sodium chloride solution was recorded and analyzed with wavelet transformtechnique. The typical results showed that the EN signal is composed of distinct typeof events, which can be classified according to their scales, i.e. their time constants.Meanwhile, the energy distribution plot (EDP) can be used as "fingerprints" of ENsignals and can be very useful for analyzing EN data in the future.

  18. Aromatic quinoxaline as corrosion inhibitor for bronze in aqueous chloride solution

    Indian Academy of Sciences (India)

    N Saoudi; A Bellaouchou; A Guenbour; A Ben Bachir; E M Essassi; M El Achouri

    2010-06-01

    A new corrosion inhibitor, viz. 3-ethyl-6-méthyl-quinoxalin-2-one, 1-benzyl-6-methyl-quinoxalin- 2-one, 2-benzyloxy-3,6-dimethyl-quinoxaline, 1-benzyl-3-methyl-quinoxalin-2-one, were synthesized in the laboratory. Their influence on the inhibition on corrosion of bronze in aqueous chloride solution (3% NaCl) was studied by electrochemical polarization methods and weight-loss measurements. The impact of temperature on the effectiveness of the substances mentioned above has been determined between 20 and 60°C. The results showed that the corrosion resistance was greatly enhanced in the presence of inhibitor and that the effectiveness depends on some physicochemical properties of the molecule, related to its functional groups. These compounds act through the formation of a protective film on the surface of the alloy.

  19. Solid solution barium–strontium chlorides with tunable ammonia desorption properties and superior storage capacity

    DEFF Research Database (Denmark)

    Bialy, Agata; Jensen, Peter Bjerre; Blanchard, Didier

    2015-01-01

    with spray drying and in situ thermogravimetric and structural characterization, we synthesize a range of new, stable barium-strontium chloride solid solutions with superior ammonia storage densities. By tuning the barium/strontium ratio, different crystallographic phases and compositions can be obtained......Metal halide ammines are very attractive materials for ammonia absorption and storage—applications where the practically accessible or usable gravimetric and volumetric storage densities are of critical importance. Here we present, that by combining advanced computational materials prediction...... with different ammonia ab- and desorption properties. In particular it is shown, that in the molar range of 35–50% barium and 65–50% strontium, stable materials can be produced with a practically usable ammonia density (both volumetric and gravimetric) that is higher than any of the pure metal halides...

  20. Effect of Electrochemical Treatment in a Lithium Chloride Solution on Field Emission from Carbon Nanotubes

    Institute of Scientific and Technical Information of China (English)

    WANG Qiang; LI Chun; YUAN Guang; GU Chang-Zhi

    2009-01-01

    Carbon nanotubes (CNTs) are electrochemically treated in a lithium chloride solution at a concentration 0.1 mol/L.The field emission properties of the CNTs are investigated at different temperatures before and after the electrochemical treatment.After treatment,the turn-on voltage to produce field emission current of 10 μA decreases from 4.2kV to 2.7kV and the field emission current increases distinctly,but the stability falls off.Based on the Fowler-Nordheim plot,the values of the work function for the CNTs are calculated,which reveals that work function decreases after the electrochemical treatment.These results are attributed to the decrease of the work function of the carbon nanotubes.

  1. Corrosion Fatigue of Austenitic Stainless Steel in Different Hot Chloride Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Visser, A.; Mori, G.; Panzenboeck, M. [Montanuniversitaet Leoben, Leoben (Austria); Pippan, R. [Erich Schmid Institute of Materials Science, Austrian Academy of Science, Leoben (Austria)

    2015-08-15

    Austenitic stainless steel was investigated under cyclic loading in electrolytes with different chloride contents and pH and at different temperatures. The testing solutions were 13.2 % NaCl (80,000 ppm Cl-) at 80 °C and 43 % CaCl{sub 2} (275,000 ppm Cl-) at 120 °C. In addition to S-N curves in inert and corrosive media, the fracture surfaces were investigated with a scanning electron microscope (SEM) to analyse the type of attack. The experimental results showed that a sharp decrease in corrosion fatigue properties can be correlated with the occurrence of stress corrosion cracking. The correlation of occurring types of damage in different corrosion systems is described.

  2. Solid solution barium–strontium chlorides with tunable ammonia desorption properties and superior storage capacity

    Energy Technology Data Exchange (ETDEWEB)

    Bialy, Agata [Amminex Emissions Technology A/S, Gladsaxevej 363, 2860 Soeborg (Denmark); Jensen, Peter B. [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Center for Atomic-scale Materials Design, Department of Physics, Technical University of Denmark, Fysikvej 311, DK-2800 Kgs. Lyngby (Denmark); Blanchard, Didier [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Vegge, Tejs, E-mail: teve@dtu.dk [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Quaade, Ulrich J., E-mail: ujq@amminex.com [Amminex Emissions Technology A/S, Gladsaxevej 363, 2860 Soeborg (Denmark)

    2015-01-15

    Metal halide ammines are very attractive materials for ammonia absorption and storage—applications where the practically accessible or usable gravimetric and volumetric storage densities are of critical importance. Here we present, that by combining advanced computational materials prediction with spray drying and in situ thermogravimetric and structural characterization, we synthesize a range of new, stable barium-strontium chloride solid solutions with superior ammonia storage densities. By tuning the barium/strontium ratio, different crystallographic phases and compositions can be obtained with different ammonia ab- and desorption properties. In particular it is shown, that in the molar range of 35–50% barium and 65–50% strontium, stable materials can be produced with a practically usable ammonia density (both volumetric and gravimetric) that is higher than any of the pure metal halides, and with a practically accessible volumetric ammonia densities in excess of 99% of liquid ammonia. - Graphical abstract: Thermal desorption curves of ammonia from Ba{sub x}Sr{sub (1−x)}Cl{sub 2} mixtures with x equal to 0.125, 0.25 and 0.5 and atomic structure of Sr(NH{sub 3}){sub 8}Cl{sub 2}. - Highlights: • Solid solutions of strontium and barium chloride were synthesized by spray drying. • Adjusting molar ratios led to different crystallographic phases and compositions. • Different molar ratios led to different ammonia ab-/desorption properties. • 35–50 mol% BaCl{sub 2} in SrCl{sub 2} yields higher ammonia density than any other metal halide. • DFT calculations can be used to predict properties of the mixtures.

  3. Mercury adsorption on granular activated carbon in aqueous solutions containing nitrates and chlorides.

    Science.gov (United States)

    Di Natale, F; Erto, A; Lancia, A; Musmarra, D

    2011-09-15

    Adsorption is an effective process to remove mercury from polluted waters. In spite of the great number of experiments on this subject, the assessment of the optimal working conditions for industrial processes is suffering the lack of reliable models to describe the main adsorption mechanisms. This paper presents a critical analysis of mercury adsorption on an activated carbon, based on the use of chemical speciation analysis to find out correlations between mercury adsorption and concentration of dissolved species. To support this analysis, a comprehensive experimental study on mercury adsorption at different mercury concentrations, temperatures and pH was carried out in model aqueous solutions. This study pointed out that mercury capture occurs mainly through adsorption of cationic species, the adsorption of anions being significant only for basic pH. Furthermore, it was shown that HgOH(+) and Hg(2+) are captured to a higher extent than HgCl(+), but their adsorption is more sensitive to solution pH. Tests on the effect of temperature in a range from 10 to 55 °C showed a peculiar non-monotonic trend for mercury solution containing chlorides. The chemical speciation and the assumption of adsorption exothermicity allow describing this experimental finding without considering the occurrence of different adsorption mechanisms at different temperature.

  4. A study of the electrochemical behavior in tungsten and caustic solutions and platinum/iridium in chloride solutions, informal report

    Energy Technology Data Exchange (ETDEWEB)

    Vitus, C.M.; Isaacs, H.S. [Brookhaven National Lab., Upton, NY (United States); Schroeder, V. [Univ. of California, Berkeley, CA (United States). College of Engineering

    1994-11-22

    Platinum/iridium and tungsten wires were electronically etched in chloride and caustic solution, respectively, to produce tips with high aspect ratio. A direct relationship between the meniscus and the aspect ratio of etched tips was established. Scanning electron micrographs indicated that higher aspect ratios were obtained by changing the geometry of the meniscus during the etch either by an increase in the applied a.c. voltage or with the addition of a nonpolar layer above the electrolytic solution during the etching process. Above the breakdown voltage, two possible mechanisms appeared to control the etching process by expediting chemical dissolution: cavitation and sparking. Cavitation caused erosion due to the force of evolved gases against the electrode and sparking attacked the surface by vaporizing the metal. Sparking commenced on both wires near 24V. This voltage corresponded to a minimum in the plot of total etch time versus voltage. From light emission studies, sparking on Pt/Ir was associated with the ionization of Pt, Ir, Ca, and Cl. A compositional analysis of insoluble black particles produced during a.c. and d.c. etching of Pt/Ir revealed Pt and Ir as the major constituents of the product. The sparking process was shown to have a potential use in micromachining.

  5. Electrochemical corrosion behavior of Cu-40Ni-20Cr alloys with different grain sizes in solutions containing chloride ions

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The electrochemical corrosion behavior of the two Cu-40Ni-20Cr alloys prepared by conventional casting(CA) and mechanical alloying(MA) with the different grain sizes was studied by using open-circuit potential(OCP), potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) methods in solutions containing chloride ions. The results show that the free corrosion potentials of the two alloys move towards negative values, corrosion currents increase and therefore corrosion rates become faster with the increase of chloride ion concentrations. EIS plots of CACu-40Ni-20Cr alloy are composed of single capacitive loop, while EIS plots of MACu-40Ni-20Cr alloy are composed of double capacitive loops in solution containing lower chloride ion concentrations. EIS plots of the two alloys have Warburg impedance with the increase of chloride ion concentrations.Corrosion rates of MACu-40Ni-20Cr alloy become faster than those of CACu-40Ni-20Cr alloy obviously in solutions containing the same chloride ion concentrations because MACu-40Ni-20Cr alloy is able to produce large concentrations of grain boundaries in the course of reduction in grain size by mechanical alloying.

  6. Solubility of some alkali and alkaline earth chlorides in water at moderate temperatures

    Science.gov (United States)

    Clynne, M.A.; Potter, R.W.

    1979-01-01

    Solubilities for the binary systems, salt-H2O, of the chlorides of lithium, rubidium, cesium, magnesium, calcium, strontium, and barium from near 0??C to the saturated boiling point are reported. The experimental data and coefficients of an equation for a smoothed curve describing each system are listed in the tables. The data are improvements on those previously reported in the literature, having a precision on the average of ??0.09%.

  7. Rare Earth Stearates as Thermal Stabilizers for Rigid Poly(vinyl chloride)

    Institute of Scientific and Technical Information of China (English)

    Zheng Yuying; Cai Weilong; Fu Minglian; Wang Canyao; Zhang Xing

    2005-01-01

    A series of stearates with different rare-earth ion were investigated as thermal stabilizers for rigid PVC at 180 ℃ in air. Their stabilizing efficiency was based on measuring the rate of dehydrochlorination. The resulted revealed the higher stabilizing efficiency of the investigated rare-earth stearates as thermal stabilizers for rigid PVC compared with the thermal stabilizers for industry: calcium stearate, zinc stearate, butyl stannum mercaptide, phosphite esters, β-diketone and epoxidized sunflower oil. This was well illustrated by longer incubation period (TS) values and lower rate of dehydrochlorination. The stable efficiency was affected by the nature of rare-earth element's individual electronic shell. The mechanism for the stabilizing effect of rare-earth stearates was proposed. The result was experimentally proved based on IR spectrum.

  8. Optimized atomistic force fields for aqueous solutions of Magnesium and Calcium Chloride: Analysis, achievements and limitations

    Science.gov (United States)

    Elfgen, Roman; Hülsmann, Marco; Krämer, Andreas; Köddermann, Thorsten; Kirschner, Karl N.; Reith, Dirk

    2016-10-01

    Molecular simulations are an important tool in the study of aqueous salt solutions. To predict the physical properties accurately and reliably, the molecular models must be tailored to reproduce experimental data. In this work, a combination of recent global and local optimization tools is used to derive force fields for MgCl2 (aq) and CaCl2 (aq). The molecular models for the ions are based on a Lennard-Jones (LJ) potential with a superimposed point charge. The LJ parameters are adjusted to reproduce the bulk density and shear viscosity of the different solutions at 1 bar and temperatures of 293.15, 303.15, and 318.15 K. It is shown that the σ-value of chloride consistently has the strongest influence on the system properties. The optimized force field for MgCl2 (aq) provides both properties in good agreement with the experimental data over a wide range of salt concentrations. For CaCl2 (aq), a compromise was made between the bulk density and shear viscosity, since reproducing the two properties requires two different choices of the LJ parameters. This is demonstrated by studying metamodels of the simulated data, which are generated to visualize the correlation between the parameters and observables by using projection plots. Consequently, in order to derive a transferable force field, an error of ˜3% on the bulk density has to be tolerated to yield the shear viscosity in satisfactory agreement with experimental data.

  9. Peptide-based biocoatings for corrosion protection of stainless steel biomaterial in a chloride solution.

    Science.gov (United States)

    Muruve, Noah G G; Cheng, Y Frank; Feng, Yuanchao; Liu, Tao; Muruve, Daniel A; Hassett, Daniel J; Irvin, Randall T

    2016-11-01

    In this work, PEGylated D-amino acid K122-4 peptide (D-K122-4-PEG), derived from the type IV pilin of Pseudomonas aeruginosa, coated on 304 stainless steel was investigated for its corrosion resistant properties in a sodium chloride solution by various electrochemical measurements, surface characterization and molecular dynamics simulation. As a comparison, stainless steel electrodes coated with non-PEGylated D-amino acid retroinverso peptide (RI-K122-4) and D-amino acid K122-4 peptide (D-K122-4) were used as control variables during electrochemical tests. It was found that the D-K122-4-PEG coating is able to protect the stainless steel from corrosion in the solution. The RI-K122-4 coating shows corrosion resistant property and should be investigated further, while the D-K122-4 peptide coating, in contrast, shows little to no effect on corrosion. The morphological characterizations support the corrosion resistance of D-K122-4-PEG on stainless steel. The adsorption of D-K122-4 molecules occurs preferentially on Fe2O3, rather than Cr2O3, present on the stainless steel surface. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Pulsation Solution to the Equation of Earth's Gravitational Field (Main Outcome)

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Using d'Alembert equation as the approximation of Einstein's equation, a solution is given in this paper to the time-dependent gravitational equation of the Earth in consideration of the Earth's features, which describes the characteristics of pulsation of the Earth and the structures of spherical layers of its interior, thus providing a theoretical basis for establishing the idea of mantle pulsation.

  11. Composition and structure of Pt chloride complexes in hydrothermal solutions, according to X-ray absorption spectroscopy

    Science.gov (United States)

    Tagirov, B. R.; Trigub, A. L.; Selivanov, P. V.; Koroleva, L. A.

    2017-03-01

    The local atomic environment of Pt in chloride solutions is studied at 25 and 300-350°C via X-ray absorption spectroscopy. A comparison of the Pt L 3-edge XANES spectra for aqueous chloride solutions and reference compounds (K2PtCl4 and K2PtCl6) shows that platinum is in oxidation state +2 at all temperatures, and the complex composition remains unchanged in the experimental range of temperatures (25-350°C) and solution compositions ( m(Cltot) > 0.4 mol kg-1 of H2O). Based on EXAFS spectral analysis, the composition of the complex being dominant in chloride solutions is found to be PtCl4 2- with interatomic Pt-Cl distances of 2.31 ± 0.01 Å, regardless of the temperature. It is concluded that the local environments of Pt and Pd in hydrothermal solutions are similar, and the main form of transfer for these metals is a square-planar complex with four Cl ligands and identical interatomic distances.

  12. Pitting corrosion of Al2024-T3 in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Pitting corrosion behavior of Al2024-T3 in sodium chloride solution was investigated by using potentiodynamic scanning (PDS) measurements and electrochemical impedance spectroscopy (EIS) technique. When pitting corrosion of the alloy occurs, there exists a passive region in the anodic branch of PDS polarization curve, which is enlarged with the increasing of immersion time due to the competition of the halide ions with OH- ions to adsorb on the oxide film to form the corrosion products film and the increase of pitting corrosion area. Two capacitive semicircles were observed in complex plane plot. For more extensive pitting and general corrosion of Al2024-T3, the passive region in PDS disappeared, while another depressed semicircle was observed in Nyquist plot because of the formation of corrosion products film. On the other hand, the low frequency inductive loop, which had often been regarded as a manifestation of pitting or formation and precipitation of a salt film, was not observed, which indicates that the low frequency inductive loop can not be the characteristic of pitting corrosion or the formation of salt film. The results also show that higher reactant CPE exponent values will correspond to more extensive transformation of a metal surface by very localized corrosion, while general corrosion can result in a smaller CPE exponent value.

  13. Electrochemical noise characteristics in corrosion process of AZ91D magnesium alloy in neutral chloride solution

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-jun; ZHU Xu-bei; ZHANG Zhao; ZHANG Jian-qing

    2009-01-01

    The corrosion process of AZ91D magnesium alloy in neutral 1% (mass fraction) sodium chloride aqueous solution was investigated by electrochemical noise(EN), SEM and EDX. Fractal theory was primarily used to depict the corrosion process of the alloy. The fast wavelet transform(FWT), as well as the fast Fourier transform(FFT), was employed to analyze the EN data. The results show that the overall corrosion process can be described by three stages. The first stage corresponds to the pit nucleation and growth; the second stage involves the growth of a passive oxide layer; and the third stage involves reactivation. With increasing immersion time, fractal dimension increases fast initially, fluctuates in the medium and increases again at last. Pitting corrosion and fractal dimension increase due to the initiation and formation of pits in the initial and the end of immersion, while depresses due to the passivation in the medium period. The results of SEM and EDX support the above conclusions.

  14. Formation of black nickel in leaching solution containing ammonia and chloride

    Institute of Scientific and Technical Information of China (English)

    ZHENG Guo-qu; ZHENG Li-feng; CAO Hua-zhen

    2005-01-01

    The black nickel formation process in leaching solution containing ammonia and chloride was investigated in terms of cyclic voltammetric and galvanostatic reduction techniques.The structure of black nickel was examined by means of X-ray diffraction technique.The results show that in the scanning region,two oxidization current peaks are observed during the positive sweep,one of which is attributed to a valence state transformation of Ni(OH)2 to high valence nickel compound(black nickel),and the other is caused by nitrogen evolution.During the formation process of black nickel,γ-NiOOH probably tends to self-discharge with water to form α-Ni(OH)2.As a result,it is observed that Ipa/Ipc(Ipa-anodic peak current;Ipc-cathodic peak current) maintains at a constant with the scanning rate increasing.Two reduction current peaks in cyclic voltammogram and two potential plateaus in galvanostatic reduction curve for black nickel are ascribed to the reduction of various oxidization states of nickel oxide.The potential plateaus at about 0.75 V reach the maximum in galvanostatic reduction curves.Black nickel presents amorphous structure.

  15. The Influence of Calcium Chloride Salt Solution on the Transport Properties of Cementitious Materials

    Directory of Open Access Journals (Sweden)

    Yaghoob Farnam

    2015-01-01

    Full Text Available The chemical interaction between calcium chloride (CaCl2 and cementitious binder may alter the transport properties of concrete which are important in predicting the service life of infrastructure elements. This paper presents a series of fluid and gas transport measurements made on cementitious mortars before and after exposure to various solutions with concentrations ranging from 0% to 29.8% CaCl2 by mass. Fluid absorption, oxygen diffusivity, and oxygen permeability were measured on mortar samples prepared using Type I and Type V cements. Three primary factors influence the transport properties of mortar exposed to CaCl2: (1 changes in the degree of saturation, (2 calcium hydroxide leaching, and (3 formation of chemical reaction products (i.e., Friedel’s salt, Kuzel’s salt, and calcium oxychloride. It is shown that an increase in the degree of saturation decreases oxygen permeability. At lower concentrations (~12%, the formation of chemical reaction products (mainly calcium oxychloride is a dominant factor decreasing the fluid and gas transport in concrete.

  16. Lithium chloride ionic association in dilute aqueous solution: a constrained molecular dynamics study

    Science.gov (United States)

    Zhang, Zhigang; Duan, Zhenhao

    2004-02-01

    Constrained molecular dynamics simulations were carried out to investigate the lithium chloride ionic associations in dilute aqueous solutions over a wide temperature range. Solvent mediated potentials of mean force have been carefully calculated at different thermodynamic conditions. Two intermediate states of ionic association can be well identified with an energy barrier from the oscillatory free energy profile. Clear pictures for the microscopic association structures are presented with a remarkable feature of strong hydration effect of lithium ion and the bridging role of its hydrating complex. Experimental association constants have been reasonably reproduced and a general trend of the increasing ionic association at high temperatures and low densities was observed. Additional simulations with different numbers of water molecules have been performed to check the possible artifacts introducing from periodic and finite size effects and confirm the reliability of our simulation results. Marginal differences of the simulated curves are believed to result from the significant compensation and canceling effect between the bare ionic forces and solvent induced mean force. Finally we confirmed the importance of accurate descriptions of dielectric properties of solvent in the ionic association study.

  17. Electrochemical, galvanic, and mechanical responses of grade 2 titanium in 6% sodium chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Z.F.; Briant, C.L.; Kumar, K.S. [Brown Univ., Providence, RI (United States). Div. of Engineering

    1999-02-01

    The electrochemical, galvanic, and mechanical responses of grade 2 titanium in 6% sodium chloride (NaCl) solution at different temperatures were investigated. The initial corrosion potential and cathodic reaction rate increased with decreasing pH and increasing temperature. The initial corrosion potential changed when titanium was coupled with other metals. Naval brass and alloy 600 (UNS N06600) anodically polarized titanium, while zinc and aluminum caused titanium to become a cathode. HY80 steel (UNS K31820), type 316 stainless steel ([SS] UNS S31600), and Monel K500 (UNS N05500, a copper-nickel alloy), polarized titanium anodically or cathodically depending upon temperature and pH. Hydrides formed on the titanium surface at potentials < {approximately} {minus}600 mV{sub SCE} to {minus}700 mV{sub SCE}. Zinc at all temperatures and HY80 at high temperatures caused hydride formation in titanium when coupled galvanically with titanium. Mechanical tests showed an {approx} 10% decrease in ductility under prior and dynamic hydrogen charging conditions.

  18. Chloride Anions Regulate Kinetics but Not Voltage-Sensor Qmax of the Solute Carrier SLC26a5.

    Science.gov (United States)

    Santos-Sacchi, Joseph; Song, Lei

    2016-06-07

    In general, SLC26 solute carriers serve to transport a variety of anions across biological membranes. However, prestin (SLC26a5) has evolved, now serving as a motor protein in outer hair cells (OHCs) of the mammalian inner ear and is required for cochlear amplification, a mechanical feedback mechanism to boost auditory performance. The mechanical activity of the OHC imparted by prestin is driven by voltage and controlled by anions, chiefly intracellular chloride. Current opinion is that chloride anions control the Boltzmann characteristics of the voltage sensor responsible for prestin activity, including Qmax, the total sensor charge moved within the membrane, and Vh, a measure of prestin's operating voltage range. Here, we show that standard narrow-band, high-frequency admittance measures of nonlinear capacitance (NLC), an alternate representation of the sensor's charge-voltage (Q-V) relationship, is inadequate for assessment of Qmax, an estimate of the sum of unitary charges contributed by all voltage sensors within the membrane. Prestin's slow transition rates and chloride-binding kinetics adversely influence these estimates, contributing to the prevalent concept that intracellular chloride level controls the quantity of sensor charge moved. By monitoring charge movement across frequency, using measures of multifrequency admittance, expanded displacement current integration, and OHC electromotility, we find that chloride influences prestin kinetics, thereby controlling charge magnitude at any particular frequency of interrogation. Importantly, however, this chloride dependence vanishes as frequency decreases, with Qmax asymptoting at a level irrespective of the chloride level. These data indicate that prestin activity is significantly low-pass in the frequency domain, with important implications for cochlear amplification. We also note that the occurrence of voltage-dependent charge movements in other SLC26 family members may be hidden by inadequate

  19. Electrochemical and SEM study on Type 254 SMO stainless steel in chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Abd El Meguid, E.A.; Abd El Latif, A.A

    2004-10-01

    An investigation was conducted to examine the critical crevice potential (E{sub crev}) and the critical protection potential (E{sub prot}) for Type 254 SMO stainless steel in 4% NaCl solution by using potentiodynamic cyclic anodic polarization (PCAP) technique at temperature ranging from 30 to 90 deg. C. The critical crevice temperature (CCT) and the critical crevice protection temperature (T{sub prot}) were determined by plotting the values of breakdown potential and E{sub prot} versus solution temperature, respectively. The values of CCT and T{sub prot} were recorded at the abrupt transition with increasing the temperature from transpassive corrosion to crevice corrosion and were found to be at 55 and 52 deg. C, respectively. Above CCT (70 deg. C) the following points were recorded. The E{sub crev} and E{sub prot} decreased linearly with log [Cl{sup -}]. The addition of bromide ions to chloride ions at a fixed halide content of 4% increased both E{sub crev} and E{sub prot}. The E{sub crev} value in 4% NaCl increased linearly with increasing pH in the range 1-10. The addition of 0.5 M bicarbonate ions to 4% NaCl completely removed the crevices effect while increasing the addition of sulphate ions to 4% NaCl increased both of E{sub crev} and E{sub prot}. The morphology of the crevice corrosion produced on the steel surface was examined by scanning electron microscope (SEM) after PCAP treatment under different test conditions.

  20. Neutron Diffraction of Aqueous Tetramethylammonium Chloride (TMA) Solutions and TMA Intercalated Swelling Clays Under Burial Conditions

    Science.gov (United States)

    Patel, R.; Howard, C. A.; Greenwell, C.; Youngs, T.; Soper, A. K.; Skipper, N. T.

    2014-12-01

    There is a need for the improvement and optimisation of clay swelling inhibitors for the enhancement of oil and gas exploration. The hydration region of both ions and the possibility of ion pairing in 1 molar aqueous solution of clay swelling inhibitor, tetramethylammonium chloride (TMACl), in D2O, under elevated hydrostatic-pressures and temperatures has been determined with unprecedented detail using a combination of neutron diffraction and small-angle scattering in conjunction with hydrogen/deuterium isotopic labeling. The O-H correlation function (H-bonds) for the water in the 1.0M solution is measured and compared with that for pure D2O. Also investigated is the effect of burial conditions on the d-spacing of TMA-intercalated vermiculite. Contrary to expectations, no aggregation of TMA ions due to hydrophobic interactions is observed, nor are any ionic pairs of TMA+ and Cl- at these burial conditions. The data revealed a more ordered water-water structure with the addition of TMACl from bulk D2O. There is no change in the hydration structure measured at the applied elevated conditions. This is in remarkable contrast to pure water at the same conditions which is well known to be compressible. The dry d-spacing of the TMA-exchanged Eucatex vermiculite is measured at 13.66 Å which increases to 14.03 Å with the addition of D2O. Beyond this, there is no change in d-spacing with increasing pressure and temperature indicating the strength of the TMA ions binding to the clay interlayers and therefore its performance as a clay-swelling inhibitor.

  1. Chloride Ion Transmission Model under the Drying-wetting Cycles and Its Solution

    Institute of Scientific and Technical Information of China (English)

    HUANG Ying; WEI Jun; DONG Rongzhen; ZENG Hua

    2014-01-01

    The chloride ion transmission model considering diffusion and convection was established respectively for different zones in concrete by analyzing chloride ion transmission mechanism under the drying-wetting cycles. The finite difference method was adopted to solve the model. The equation of chloride ion transmission model in the convection and diffusion zone of concrete was discreted by the group explicit scheme with right single point (GER method) and the equation in diffusion zone was discreted by FTCS difference scheme. According to relative humidity characteristics in concrete under drying-wetting cycles, the seepage velocity equation was formulated based on Kelvin Equation and Darcy’s Law. The time-variant equations of chloride ion concentration of concrete surface and the boundary surface of the convection and diffusion zone were established. Based on the software MATLAB the numerical calculation was carried out by using the model and basic material parameters from the experiments. The calculation of chloride ion concentration distribution in concrete is in good agreement with the drying-wetting cycles experiments. It can be shown that the chloride ion transmission model and the seepage velocity equation are reasonable and practical. Studies have shown that the chloride ion transmission in concrete considering convection and diffusion under the drying-wetting cycles is the better correlation with the actual situation than that only considering the diffusion.

  2. Passivation of duplex stainless steel in solutions simulating chloride-contaminated concrete

    Directory of Open Access Journals (Sweden)

    Takenouti, H.

    2007-12-01

    Full Text Available Most studies published to date on the corrosion behaviour of stainless reinforcing steel are based on austenitic steel. The market presence of corrugated duplex steel is growing, however. The present study compared passivity in 2205 type duplex and 304 type austenitic stainless steel. Polarization tests in chloride-containing Ca(OH2 solutions confirmed the exceptional performance of duplex steels. X-ray photoelectronic spectroscopy (XPS showed that the passive layer generated on duplex stainless steel in media simulating concrete pore solutions had a higher Cr content than the layer formed on steel in contact with the air. The XPS results also revealed that in duplex steel the form adopted by the passive layer Fe oxides was Fe3O4 in the solutions simulating concrete, rather than Fe2O3, as in duplex steel exposed to air. Electrochemical impedance spectroscopy (EIS can be used to monitor the transformations taking place in the passive layer and analyze the factors involved.La mayoría de los estudios publicados hasta el momento sobre el comportamiento frente a la corrosión de armaduras de acero inoxidable se basan en aceros austeníticos. Sin embargo, la presencia en el mercado de aceros corrugados dúplex es cada vez más importante. En este trabajo se analiza la pasividad de un acero inoxidable dúplex tipo 2205 en comparación con la de un inoxidable austenítico tipo 304. Los ensayos de polarización en disoluciones de Ca(OH2 con cloruros confirman el excepcional comportamiento de los aceros dúplex. La espectroscopía fotoelectrónica de rayos X (XPS informa de que la capa pasiva generada en aceros inoxidables dúplex en medios que simulan la disolución de los poros del hormigón posee mayor contenido en óxidos de Cr que la formada en aire. También se puede deducir de los resultados de XPS que los óxidos de Fe de la capa pasiva de los aceros dúplex se encuentran en forma de Fe3O4 en las disoluciones que simulan el hormigón en vez de en

  3. Aqueous Solutions of the Ionic Liquid 1-butyl-3-methylimidazolium Chloride Denature Proteins

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Gary A [ORNL; Heller, William T [ORNL

    2009-01-01

    As we advance our understanding, ionic liquids (ILs) are finding ever broader scope within the chemical sciences including, most recently, pharmaceutical, enzymatic, and bioanalytical applications. With examples of enzymatic activity reported in both neat ILs and in IL/water mixtures, enzymes are frequently assumed to adopt a quasi-native conformation, even if little work has been carried out to date toward characterizing the conformation, dynamics, active-site perturbation, cooperativity of unfolding transitions, free energy of stabilization, or aggregation/oligomerization state of enzymes in the presence of an IL solvent component. In this study, human serum albumin and equine heart cytochrome c were characterized in aqueous solutions of the fully water-miscible IL 1-butyl-3-methylimidazolium chloride, [bmim]Cl, by small-angle neutron and X-ray scattering. At [bmim]Cl concentrations up to 25 vol.%, these two proteins were found to largely retain their higher-order structures whereas both proteins become highly denatured at the highest IL concentration studied here (i.e., 50 vol.% [bmim]Cl). The response of these proteins to [bmim]Cl is analogous to their behavior in the widely studied denaturants guanidine hydrochloride and urea which similarly lead to random coil conformations at excessive molar concentrations. Interestingly, human serum albumin dimerizes in response to [bmim]Cl, whereas cytochrome c remains predominantly in monomeric form. These results have important implications for enzymatic studies in aqueous IL media, as they suggest a facile pathway through which biocatalytic activity can be altered in these nascent and potentially green electrolyte systems.

  4. Ternary solution of sodium chloride, succinic acid and water; surface tension and its influence on cloud droplet activation

    Directory of Open Access Journals (Sweden)

    J. Vanhanen

    2008-08-01

    Full Text Available Surface tension of ternary solution of sodium chloride, succinic acid and water was measured as a function of both composition and temperature by using the capillary rise technique. Both sodium chloride and succinic acid are found in atmospheric aerosols, the former being main constituent of marine aerosol. Succinic acid was found to decrease the surface tension of water already at very low concentrations. Sodium chloride increased the surface tension linearly as a function of the concentration. Surface tensions of both binary solutions agreed well with the previous measurements. Succinic acid was found to lower the surface tension even if sodium chloride is present, indicating that succinic acid, as a surface active compound, tends to concentrate to the surface. An equation based on thermodynamical relations was fitted to the data and extrapolated to the whole concentration range by using estimated surface tensions for pure compounds. As a result, we obtained an estimate of surface tensions beyond solubility limits in addition to a fit to the experimental data. The parameterization can safely be used at temperatures from 10 to 30°C. These kinds of parameterizations are important for example in atmospheric nucleation models. To investigate the influence of surface tension on cloud droplet activation, the surface tension parameterization was included in an adiabatic air parcel model. Usually in cloud models the surface tension of pure water is used. Simulations were done for characteristic marine aerosol size distributions consisting of the considered ternary mixture. We found that by using the surface tension of pure water, the amount of activated particles is underestimated up to 8% if particles contain succinic acid and overestimated it up to 8% if particles contain only sodium chloride. The surface tension effect was found to increase with increasing updraft velocity.

  5. STUDY OF CHEMICAL INTERACTION OF MAGNESIA CEMENT WITH HIGH CONCENTRATION MAGNESIUM CHLORIDE SOLUTIONS

    Directory of Open Access Journals (Sweden)

    DEREVIANKO V. N.

    2015-10-01

    Full Text Available Problem statement. In activating MgO by electrolyte salts, as a result of formation of non water-resist magnesium silicate hydrate are obtained the durable cement stone having the low water-resist. I. P. Vyrodov considers [9; 5], that magnesia cement curing in mixing with sufficiently concentrated (C > 20 % solutions MgCl2 is caused with the crystallization of oxyhydrochloride composition: 3MgO∙MgCl2∙11Н2О, 5MgO∙MgCl2∙13Н2О and 7MgO∙MgCl2∙15Н2О. In the lower concentration parts of MgCl2 solution is formed a transitional compound of Mg[(OHnCl2-n] with isomorphous Mg(OH2 structure. At very low Cl concentration only Mg(OH2 is practically formed. Purpose. The Formation of water-resist magnesium silicate hydrates for obtaining of fast curing and solid structure of the magnesia stone. Conclusion. The dependence of the formation of the magnesia stone from the ratio (MgO/MgCl2 of the magnesia cement (MgO and the magnesium chloride solution (MgCl2 of different density has been identified in order to obtain the best content for oxyhydrochloride 3MgO•MgCl2•11Н2О, 5MgO•MgCl2•13Н2О and magnesium hydroxide (Mg(OH2. In putting into the system MgO∙–∙H2О of the silicic acid or fine ground quartz grains with size of less than 20 – 30 microns, over 1 month for the magnesium silicate hydrates formation is needed, where from 2 to 5 % of the total number of newgrowths are created. The study is proved by the expert opinion, that magnesium silicate hydrates do not have binding properties, unlike calcium silicate hydrates, and the main role in the system curing is played with the Mg(OH2 gel recrystallization, which provides the acceptable stone strength (R ≈ 30MPa in a few years. It has been also established, that in mixing of cement with low concentration MgO solutions of less than 1,5 mol/l (or 13% 1,1g/sm3, the final product in the stone structure is Mg(OH2. With increasing the sealer (MgCl2 solution there is formed by turn in

  6. Chloride Transport of High Alumina Cement Mortar Exposed to a Saline Solution

    Directory of Open Access Journals (Sweden)

    Hee Jun Yang

    2016-01-01

    Full Text Available Chloride transport in different types of high alumina cement (HAC mortar was investigated in this study. Three HAC cement types were used, ranging from 52.0 to 81.1% of aluminum oxides in clinker. For the development of the strength, the setting time of fresh mortar was measured immediately after mixing and the mortar compressive strength was cured in a wet chamber at 25 ± 2°C and then measured at 1–91 days. Simultaneously, to assess the rate of chloride transport in terms of diffusivity, the chloride profile was performed by an exposure test in this study, which was supported by further experimentation including an examination of the pore structure, chloride binding, and chemical composition (X-ray diffraction analysis. As a result, it was found that an increase in the Al2O3 content in the HAC clinker resulted in an increase in the diffusion coefficient and concentration of surface chloride due to increased binding of chloride. However, types of HAC did not affect the pore distribution in the cement matrix, except for macro pores.

  7. Effect of Organic Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in Chloride Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Ilevbare, G O; Rebak, R B

    2007-08-28

    Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and picric acids showed a slightly higher corrosion rate, and acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids.

  8. Correction of Hemodynamics with Hypertonic Sodium Chloride Solution in Critical Conditions

    Directory of Open Access Journals (Sweden)

    P. S. Zhbannikov

    2007-01-01

    Full Text Available Objective: to assess the capabilities of small-volume hypertonic infusion in the context of early goal-directed therapy for critical conditions in surgical patients.Subjects and methods. Twenty-nine patients (SAPS II 47.5±6.81 scores operated on for generalized peritonitis (n=24 or severe concomitant injury with damages to chest and/or abdominal organs (n=5 who had the clinical and laboratory signs of a systemic inflammatory reaction were intravenously injected 4 ml/kg of 7.5% of hypertonic sodium chloride solution (HS and colloidal solution, followed by infusion and, if indicated, inotropic maintenance of hemodynamics for 6 hours in order to achieve the goal vales of mean blood pressure (BP, central venous pressure (CVP, central venous blood oxygen saturation (ScvO2, and diuresis. Plasma concentrations of sodium, chlorine, and lactate, acid-base balance, and osmotic blood pressure were monitored.Results. The patients were found to have infusion therapy-refractory critical arterial hypotension, low ScvO2, and oliguria before small-volume circulation maintenance. In all the patients, HS infusion originally caused a rapid rise in BP up to the goal value, with its further colloid infusion maintenance requiring additional dopamine infusion in 12 patients and red blood cell transfusion in 3. This could stabilize over 6 hours BP at the required level in 25 patients, in 9 of whom CVP only approximated the goal value. All the patients were found to have a significant increase in ScvO2 up to an average of 68% in response to HP infusion after 30—60 minutes; in 14 out of them ScvO2 exceeded 70%. By hour 6, ScvO2 stabilized at its goal level in 23 (79% examinees. Administration of HS caused a significantly increased diuresis. In patients with recovered renal function, the observed hypernatremia, hyperchloremia with hyperchloremic acidosis were transient.Conclusion. The results of the study show it possible to include small-volume hypertonic infusion at

  9. [Removal of nitrate from aqueous solution using cetylpyridinium chloride (CPC)-modified activated carbon as the adsorbent].

    Science.gov (United States)

    Zheng, Wen-Jing; Lin, Jian-Wei; Zhan, Yan-Hui; Fang, Qiao; Yang, Meng-Juan; Wang, Hong

    2013-11-01

    Surfactant-modified activated carbon (SMAC) was prepared by loading cetylpyridinium chloride (CPC) onto activated carbon and used as adsorbents to remove nitrate from aqueous solution. The SMAC was effective for removing nitrate from aqueous solution. The SMAC exhibited much higher nitrate adsorption capacity than that of the unmodified activated carbon. The nitrate adsorption capacity for SMAC increased with increasing the CPC loading. The adsorption kinetics of nitrate on SMAC followed a pseudo-second-order kinetic model. The equilibrium adsorption data of nitrate on SMAC could be described by the Langmuir isotherm model. Based on the Langmuir isotherm model, the maximum nitrate adsorption capacity for SMAC with CPC loading amount of444 mmol per 1 kg activated carbon was determined to be 16.1 mg x g(-1). The nitrate adsorption capacity for SMAC decreased with the increasing solution pH. The presence of competing anions such as chloride, sulfate and bicarbonate reduced the nitrate adsorption capacity. The nitrate adsorption capacity for SMAC slightly decreased with the increasing reaction temperature. Almost 95% of nitrate molecules adsorbed on SMAC could be desorbed in 1 mol x L(-1) NaCl solution. The main mechanisms for the adsorption of nitrate on SMAC are anionic exchange and electrostatic attraction. The results of this work indicate that SMAC is a promising adsorbent for removing nitrate from aqueous solution.

  10. Electrolytic reduction of U(VI) to U(IV) in acidic chloride and acidic sulfate solutions

    Science.gov (United States)

    Majima, Hiroshi; Awakura, Yasuhiro; Hirono, Shuichiro

    1986-01-01

    In order to examine the applicability of the electrolytic reduction process of U(VI) (originally developed for the chloride system by PNC) to the sulfate solution system, a fundamental study was made. In this study, the concentrations of various chemical species in the catholytes were calculated at 298 K at various percentages of uranium reduction, taking the chloro-complex and sulfato-complex formation reactions of uranium into consideration. The polarization characteristics of the electrolytic reduction of uranyl chloride and uranyl sulfate were determined, using titanium and platinum cathodes, respectively, at 303 ± 1 K. In conjunction with this process, the electrical conductivity of the catholyte, the electrical resistivity of the cation exchange membrane, and the diffusion coefficient of uranyl sulfate were also determined.

  11. Lactated Ringer's solution or 0.9% sodium chloride as fluid therapy in pigeons (Columba livia submitted to humerus osteosynthesis

    Directory of Open Access Journals (Sweden)

    Adriano B. Carregaro

    2015-01-01

    Full Text Available The study aimed to compare the effects of intraosseous infusion of lactated Ringer's and 0.9% sodium chloride solutions on the electrolytes and acid-base balance in pigeons submitted to humerus osteosynthesis. Eighteen pigeons were undergoing to isoflurane anesthesia by an avalvular circuit system. They were randomly assigned into two groups (n=9 receiving lactated Ringer's solution (LR or 0.9% sodium chloride (SC, in a continuous infusion rate of 20mL/kg/h, by using an intraosseous catheter into the tibiotarsus during 60-minute anesthetic procedure. Heart rate (HR, and respiratory rate (RR were measured every 10 min. Venous blood samples were collected at 0, 30 and 60 minutes to analyze blood pH, PvCO2, HCO3 -, Na+ and K+. Blood gases and electrolytes showed respiratory acidosis in both groups during induction, under physical restraint. This acidosis was evidenced by a decrease of pH since 0 min, associated with a compensatory response, observed by increasing of HCO3 - concentration, at 30 and 60 min. It was not observed any changes on Na+ and K+ serum concentrations. According to the results, there is no reason for choosing one of the two solutions, and it could be concluded that both fluid therapy solutions do not promote any impact on acid-base balance and electrolyte concentrations in pigeons submitted to humerus osteosynthesis.

  12. Effects of applied potential on the stress corrosion cracking behavior of 7003 aluminum alloy in acid and alkaline chloride solutions

    Science.gov (United States)

    Zhang, Xiao-yan; Song, Ren-guo; Sun, Bin; Lu, Hai; Wang, Chao

    2016-07-01

    Potentiodynamic polarization tests and slow strain rate test (SSRT) in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) in acid and alkaline chloride solutions under various applied potentials ( E a). The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution (AD) at open-circuit potential (OCP) and is highly susceptible to hydrogen embrittlement (HE) at high negative E a in the solutions with pH levels of 4 and 11. The susceptibility increases with negative shift in the potential when E a is less than -1000 mV vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when E a is equal to -1000 mV vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.

  13. Underpotential deposition of cadmium onto Cu(111 and Cu(110 from chloride containing solutions

    Directory of Open Access Journals (Sweden)

    B. M. JOVIC

    2001-05-01

    Full Text Available Underpotential deposition (UPD of Cd onto the (111 and (110 faces of copper in chloride containing electrolyte has been investigated by cyclic voltammetry and the potentiostatic pulse technique. It was shown that the UPD of Cd onto the (111 face of copper is characterized by two pairs of peaks, one pair corresponding to the formation of the (Ö19×Ö19R23.4° structure of Cd and the other one, taking place close to the reversible potential of Cd deposition, corresponding to the alloying of Cu with Cd. Deposition of (Ö19×Ö19R23.4° structure of Cd was found to take place by the mechanism of replacement of the adsorbed structure of chloride, without chloride desorption (the chloride stays adsorbed on top of the Cd layer. Similar behaviour was found for the (110 face of copper, with more pronounced alloying which provokes an irreversible change of the original (110 surface of copper.

  14. Solution thermodynamics of rare-earth metal ions - physicochemical study-

    Energy Technology Data Exchange (ETDEWEB)

    Amerkhanova, Sh K; Shlyapov, R M; Uali, A S [Buketov Karaganda state university, University str., 28, Karaganda, 100028 (Kazakhstan)], E-mail: amerkhanova_sh@mail.ru

    2009-02-01

    The results of the studying of interactions in multicomponent systems 'polyvinyl alcohol (PVA) - rare-earth element ion - nitrate of sodium - water' are represented. It is established that for rubidium (I) ions temperature and ionic strength is render destroying action, and for yttrium (III) ions the influence of these factors has return character which is connected with features of an electronic structure of metal ion. It is revealed that a dominating role of non-electrostatic formation composed, hence, the formation of donor-acceptor connection of 'metal - ligand' occurs through atom of oxygen.

  15. Impedance and XPS study of benzotriazole films formed on copper, copper-zinc alloys and zinc in chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Kosec, Tadeja; Merl, Darja Kek [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Milosev, Ingrid [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova 39, 1000 Ljubljana (Slovenia); Orthopaedic Hospital Valdoltra, Jadranska c. 31, 6280 Ankaran (Slovenia)], E-mail: ingrid.milosev@ijs.si

    2008-07-15

    The formation of protective layers on copper, zinc and copper-zinc (Cu-10Zn and Cu-40Zn) alloys at open circuit potential in aerated, near neutral 0.5 M NaCl solution containing benzotriazole was studied using electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS). Benzotriazole (BTAH), generally known as an inhibitor of copper corrosion, also proved to be an efficient inhibitor for copper-zinc alloys and zinc metal. The surface layers formed on alloys in BTAH-inhibited solution comprised both polymer and oxide components, namely Cu(I)BTA and Zn(II)BTA polymers and Cu{sub 2}O and ZnO oxides, as proved by the in-depth profiling of the layers formed. A tentative structural model describing the improved corrosion resistance of Cu, Cu-xZn alloys and Zn in BTAH containing chloride solution is proposed.

  16. Extraction and separation of Nd(III), Sm(III), Dy(III), Fe(III), Ni(II), and Cs(I) from concentrated chloride solutions with N,N,N',N'-tetra(2-ethylhexyl) diglycolamide as new extractant

    Institute of Scientific and Technical Information of China (English)

    E.A. Mowafy; D. Mohamed

    2015-01-01

    The feasibility of using N,N,N',N'-tetra(2-ethylhexyl)diglycolamide (TEHDGA) in 75 vol.% n-dodecane-25 vol.% n-octanol as agents for the extraction and separation of Nd(III), Sm(III), Dy(III), Fe(III), Ni(II), and Cs(I) from concentrated chlo-ride solution was investigated. Different extraction behaviors were obtained towards rare earth elements (REE) studied and Fe(III), Ni(II) and Cs(I). Efficient separation of Nd(III), Sm(III) and Dy(III) from Fe(III), Ni(II), and Cs(I) was achieved by TEHDGA, depending on the HCl, HNO3 or H2SO4 concentration. A systematic investigation was carried out on the detailed extraction prop-erties of Nd(III), Sm(III), and Dy(III) with TEHDGA from chloride media. The IR spectra of the extracted species were investi-gated.

  17. Effect of benzalkonium chloride-free latanoprost ophthalmic solution on ocular surface in patients with glaucoma

    Directory of Open Access Journals (Sweden)

    Walimbe T

    2016-05-01

    Full Text Available Tejaswini Walimbe,1 Vidya Chelerkar,2 Purvi Bhagat,3 Abhijeet Joshi,4 Atul Raut4 1Walimbe Eye Clinic, 2PBMA’s H.V. Desai Eye Hospital, Pune, 3Glaucoma Clinic, M and J Western Regional Institute of Ophthalmology, Civil Hospital, Ahmedabad, 4Clinical Research Department, Sun Pharma Advanced Research Company Ltd., Mumbai, India Introduction: Benzalkonium chloride (BAK, included as a preservative in many topical treatments for glaucoma, induces significant toxicity and alters tear breakup time (TBUT. BAK-containing latanoprost, an ester prodrug of prostaglandin F2a, can cause ocular adverse events (AEs associated with BAK. The purpose of this study was to evaluate the efficacy and safety of BAK-free latanoprost. Patients and methods: A prospective, open-label, single-arm, multicenter, 8-week study in patients with primary open-angle glaucoma or ocular hypertension taking BAK-containing latanoprost for ≥12 months was performed. Patients were switched to BAK-free latanoprost ophthalmic solution 0.005% administered once daily, and eyes were assessed after 28 and 56 days. Primary efficacy and safety variables were TBUT and treatment-emergent AEs, respectively. Results: At day 56, 40 eyes were evaluable. Mean TBUT increased significantly from baseline (3.67±1.60 seconds to 5.03±2.64 and 6.06±3.39 seconds after 28 and 56 days of treatment with BAK-free latanoprost (P<0.0001. Ocular Surface Disease Index© (OSDI© score also decreased significantly to 12.06±13.40 and 7.06±10.75 at 28 and 56 days, respectively, versus baseline (18.09±18.61, P<0.0001. In addition, inferior corneal staining score decreased significantly to 0.53 from baseline (0.85, P=0.0033. A reduction in conjunctival hyperemia and intraocular pressure was observed at both time points. No treatment-related serious AEs were evident and 12 (26.08% treatment-emergent AEs occurred in seven patients, with eye pain and irritation being the most frequent. No clinically significant changes

  18. Shock Hugoniot and equations of states of water, castor oil, and aqueous solutions of sodium chloride, sucrose and gelatin

    Science.gov (United States)

    Gojani, A. B.; Ohtani, K.; Takayama, K.; Hosseini, S. H. R.

    2016-01-01

    This paper reports a result of experiments for the determination of reliable shock Hugoniot curves of liquids, in particular, at relatively low pressure region, which are needed to perform precise numerical simulations of shock wave/tissue interaction prior to the development of shock wave related therapeutic devices. Underwater shock waves were generated by explosions of laser ignited 10 mg silver azide pellets, which were temporally and spatially well controlled. Measuring temporal variation of shock velocities and over-pressures in caster oil, aqueous solutions of sodium chloride, sucrose and gelatin with various concentrations, we succeeded to determine shock Hugoniot curves of these liquids and hence parameters describing Tait type equations of state.

  19. Evidence of mass exchange between inside and outside of sonoluminescing bubble in aqueous solution of terbium chloride

    Science.gov (United States)

    Liang, Jinfu; Chen, Weizhong; Wang, Xun; Yang, Jing; Chen, Zhan

    2016-12-01

    Spectra of single-bubble sonoluminescence (SBSL) were obtained for Tb3+ ions emission lines from bubbles in an aqueous solution of terbium chloride (TbCl3). The spectra provide experimental evidence to prove that an air bubble driven by strong ultrasound will not eventually become a rectified pure argon bubble, which is not as predicted by the argon rectification hypothesis. The time-resolved spectra of SBSL show a mass exchange of material such as Tb3+ ions between the inside and outside of the bubble. With increasing sound pressure, the rate of mass exchange and the SBSL intensity increases.

  20. Effect of pore water velocities and solute input methods on chloride transport in the undisturbed soil columns of Loess Plateau

    Science.gov (United States)

    Zhou, BeiBei; Wang, QuanJiu

    2016-04-01

    Studies on solute transport under different pore water velocity and solute input methods in undisturbed soil could play instructive roles for crop production. Based on the experiments in the laboratory, the effect of solute input methods with small pulse input and large pulse input, as well as four pore water velocities, on chloride transport in the undisturbed soil columns obtained from the Loess Plateau under controlled condition was studied. Chloride breakthrough curves (BTCs) were generated using the miscible displacement method under water-saturated, steady flow conditions. Using the 0.15 mol L-1 CaCl2 solution as a tracer, a small pulse (0.1 pore volumes) was first induced, and then, after all the solution was wash off, a large pulse (0.5 pore volumes) was conducted. The convection-dispersion equation (CDE) and the two-region model (T-R) were used to describe the BTCs, and their prediction accuracies and fitted parameters were compared as well. All the BTCs obtained for the different input methods and the four pore water velocities were all smooth. However, the shapes of the BTCs varied greatly; small pulse inputs resulted in more rapid attainment of peak values that appeared earlier with increases in pore water velocity, whereas large pulse inputs resulted in an opposite trend. Both models could fit the experimental data well, but the prediction accuracy of the T-R was better. The values of the dispersivity, λ, calculated from the dispersion coefficient obtained from the CDE were about one order of magnitude larger than those calculated from the dispersion coefficient given by the T-R, but the calculated Peclet number, Pe, was lower. The mobile-immobile partition coefficient, β, decreased, while the mass exchange coefficient increased with increases in pore water velocity.

  1. Sol-gel Transition of Methylcellulose Solution in the Coexistence of Hexadecyltrimethylammonium Bromide and Sodium Chloride

    Institute of Scientific and Technical Information of China (English)

    Shah Zhou; Hai-yang Yang; Yong-jun Xie; Hua-zhen Li; Guang-ming Liu

    2011-01-01

    The sol-gel transition of methylcellulose (MC) solution in the presence of NaCl and hexadecyltrimethylammonium bromide (HTAB),together with MC/NaCl solution in the presence of HTAB and MC/HATB solution in the presence of NaCl,was investigated by the rheological measurements.It has been found that the sol-gel transition temperature of MC solution decreases linearly with the concentration of NaCl in solution but increases linearly with the concentration of HTAB in solution,respectively.However,the sol-gel transition temperature of MC/NaCl solution in the presence of HTAB keeps the same value,independent of the concentration of HTAB in solution.On the other hand,the sol-gel transition temperature of MC/HTAB solution decreases linearly with the concentration of NaCl in solution.The experimental results suggest that,for MC/NaCl solution in the presence of HTAB,the saltinduced spherical micelles of HTAB should have formed in bulk solution.For MC solution in the absence of NaCl,no spherical micelles have been formed in bulk solution,though the concentration of HTAB in our experiment is almost one order of magnitude higher than the critical micelle concentration of HTAB in polymer-free solution.In fact,due to adsorption of HTAB on MC chains,the realconcentration of HTAB in bulk solution,is much less than the apparent concentration of HTAB dissolved in MC solution.

  2. Quantitative Analysis of Volatile Impurities in Diallyldimethylammonium Chloride Monomer Solution by Gas Chromatography Coupled with Liquid-Liquid Extraction

    Directory of Open Access Journals (Sweden)

    Cheng Liu

    2017-01-01

    Full Text Available The quantitative analysis method for volatile impurities in diallyldimethylammonium chloride (DADMAC monomer solution was established in this paper. The volatile impurities were quantitatively analyzed with trichloromethane as extraction solvent and n-hexane as internal standard by using gas chromatography (GC coupled with solvent extraction, and the chromatographic conditions, quantitative methods, and extraction conditions were systematically investigated in detail. The results showed that excellent linear relationships of 5 volatile impurities (dimethylamine, allyldimethylamine, allyl chloride, allyl alcohol, and allyl aldehyde were obtained in the range of 1–100 mg·L−1. The method also showed good specificity, recovery (95.0%–107.5%, and relative standard deviation (RSD, 1.40%–7.67%. This method could accurately detect the whole volatile impurities in DADMAC monomer solution quantitatively in one time with a low detection limit. Furthermore, this method is conducive to the preparation of highly pure DADMAC monomer and the development of national and international standards of the DADMAC monomer product quality, and the results could provide a strong foundation for the regulation and mechanism research of impurities on monomer reactivity in polymerization.

  3. The role of macrocyclic compounds in the extraction and possible separation of platinum and rhodium from chloride solutions

    Science.gov (United States)

    Jyothi, Rajesh Kumar; Lee, Jin-Young

    2016-06-01

    Macrocyclic compounds (crown ethers), specifically 18-crown-6 (18-C-6), benzo-15-crown-5 (B-15-C-5), di-benzo-18-crown-6 (DB-18-C-6) and di-cyclohexano-18-crown-6 (DC-18C-6), are used as extractants as well as synergists with amine-group extractants. Platinum and rhodium belong to platinum-group metals (PGMs) and have very similar ionic radii and similar properties. The separation of PGMs is most useful for the preparation of functional materials. Macrocyclic compounds are tested for platinum and rhodium separation and are found to achieve marginal separation. Amines (used as extractants) are paired with macrocyclic compounds (used as synergists), and the separation factor between platinum and rhodium is increased with synergistic enhancement from a chloride solution. The present study discusses extraction chemistry, separation factors and the synergy between platinum and rhodium from chloride solutions. To ensure accurate data, the aqueous samples in this study are analyzed using an inductively coupled plasma optical emission spectrometer (ICP-OES).

  4. Standard practice for exposure of metals and alloys by alternate immersion in neutral 3.5% Sodium Chloride solution

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1999-01-01

    1.1 This practice covers procedures for making alternate immersion stress corrosion tests in 3.5 % sodium chloride (NaCl) (). It is primarily for tests of aluminum alloys (Test Method G 47) and ferrous alloys, but may be used for other metals exhibiting susceptibility to chloride ions. It sets forth the environmental conditions of the test and the means for controlling them. Note 1 Alternate immersion stress corrosion exposures are sometimes made in substitute ocean water (without heavy metals) prepared in accordance with Specification D 1141. The general requirements of this present practice are also applicable to such exposures except that the reagents used, the solution concentration, and the solution pH should be as specified in Specification D 1141. 1.2 This practice can be used for both stressed and unstressed corrosion specimens. Historically, it has been used for stress-corrosion cracking testing, but is often used for other forms of corrosion, such as uniform, pitting, intergranular, and galvanic. ...

  5. Effect of the salt-induced micellar microstructure on the nonlinear shear flow behavior of ionic cetylpyridinium chloride surfactant solutions

    Science.gov (United States)

    Gaudino, D.; Pasquino, R.; Kriegs, H.; Szekely, N.; Pyckhout-Hintzen, W.; Lettinga, M. P.; Grizzuti, N.

    2017-03-01

    The shear flow dynamics of linear and branched wormlike micellar systems based on cetylpyridinium chloride and sodium salicylate in brine solution is investigated through rheometric and scattering techniques. In particular, the flow and the structural flow response are explored via velocimetry measurements and rheological and rheometric small-angle neutron scattering (SANS) experiments, respectively. Although all micellar solutions display a similar shear thinning behavior in the nonlinear regime, the experimental results show that shear banding sets in only when the micelle contour length L ¯ is sufficiently long, independent of the nature of the micellar connections (either linear or branched micelles). Using rheometric SANS, we observe that the shear banding systems both show very similar orientational ordering as a function of Weissenberg number, while the short branched micelles manifest an unexpected increase of ordering at very low Weissenberg numbers. This suggests the presence of an additional flow-induced relaxation process that is peculiar for branched systems.

  6. Polymer-clay nanocomposites obtained by solution polymerization of vinyl benzyl triammonium chloride in the presence of advanced functionalized clay

    Indian Academy of Sciences (India)

    Raluca Ianchis; Dan Donescu; Ludmila Otilia Cinteza; Violeta Purcar; Cristina Lavinia Nistor; Critian Petcu; Cristian Andi Nicolae; Raluca Gabor; Silviu Preda

    2014-05-01

    Polymer-clay nanocomposites were synthesized by solution polymerization method using advanced functionalized clay and vinyl benzyl trimethyl ammonium chloride as monomer. First stage consisted in the silylation of a commercial organo-modified clay-Cl 20A using alkoxysilanes with different chain lengths. In the second step, the synthesis and characterization of polymer-nanocomposites were followed. To evaluate the clay functionalization process as well as the final polymer-clay products, thermogravimetric,X-ray diffraction, dynamic light scattering, Fourier transform infrared spectroscopy and three test liquid contact angles analyses were used. The loss of ammonium ions from commercial clay, the grafting degree, the lengths and the nature of alkyl chain influence the dispersion of the advanced modified clay into the polymer solution and, furthermore, the properties of the final polymer-clay nanocomposite film.

  7. Earth Based Views of Solute Profiles on Mars (Invited)

    Science.gov (United States)

    Amundson, R.

    2013-12-01

    'Historical accounts of planetary evolution are mostly written in stone' (1), but the last chapter of that history is embedded in its soil. Soil properties reflect the effects of prevailing environmental boundary conditions. Solute profiles are powerful indicators of the direction and magnitude of water flow. I briefly review the chemistry of salt profiles from deserts formed by upward vs. downward migrating water, use this as a basis for interpreting aspects of Mars hydrological history. The Noachian-aged Meridiani Planum land surface is exposed in the Endurance and Victoria Craters. These craters have been estimated to be ~ Letters 240:11-72. (2) Golombek, M.P. (2012) Timescale of small crater modification on Meridiani Planum, Mars. 43rd Lunar and Planetary Science Conference. (3) Arvidson et al. (2011). J. of Geophysical Research 116, E00F15, doi:10.1029/2010JE003746, 2011 (4) Amundson et al. (2008) Geochim. Cosmochim. Acta 72:3845-3864.

  8. Regioselective organocatalysis: a theoretical prediction of the selective rate acceleration of the SN2 reaction between an acetate ion and primary alkyl chlorides in DMSO solution.

    Science.gov (United States)

    Pliego, Josefredo R

    2006-05-07

    High level ab initio calculations, including the solvent effect through a continuum solvation model, predict that 1,4-benzenedimethanol is able to catalyse the S(N)2 reaction between an acetate ion and primary alkyl chlorides in dimethyl sulfoxide solution. The catalysis takes place through two selective hydrogen bonds to the transition state. However, for secondary alkyl chlorides the catalysis is not effective due to steric repulsion and desolvation. This effect induces regioselective control of S(N)2 esterification reactions.

  9. Electrochemical properties and stress corrosion cracking of alloys 600, 690, and 800 in solutions containing boric acid and chloride

    Energy Technology Data Exchange (ETDEWEB)

    Bae, J. H.; Won, C. H. [Chungnam Nation Univ., Taejon (Korea, Republic of); Lee, E. H.; Kim, H. P.; Kim, W. C. [KAERI, Taejon (Korea, Republic of)

    2000-10-01

    Electrochemical characteristics and stress corrosion cracking(SCC)of Alloy 600, Alloy 690 and Alloy 800 have been studied in boric acid solution with chloride. Electrochemical characteristics were measured in mixed solution of 3% H{sub 3}BO{sub 3} and 0.2g/l Cl{sup -} at 320 .deg. C. SCC resistance was predicted with Parameter(P{sub SCC}) including current density ratio obtained at two different scan rates. P{sub SCC} increased with a following sequence: Alloy 600MA, 600TT, 690TT and Alloy 800. SCC test was carried out with C-ring specimens and reverse U-bend(RUB) specimens at 320 .deg. C and 350 .deg. C. Test solutions were mixture of 3% H{sub 3}BO{sub 3} and 0.2g/l Cl{sup -} at 320 .deg. C and mixture of 27% H{sub 3}BO{sub 3} and 2g/l Cl{sup -} at 350 .deg. C. C-ring specimens test in the solution of 3% H{sub 3}BO{sub 3} and 0.2g/l Cl{sup -} at 320 .deg. C for 2400hrs did not show SCC. RUB specimen of Alloy600MA and 600TT showed SCC after 1920 hours exposure to the solution of 27% H{sub 3}BO{sub 3} and 0.2g/l Clat 350 .deg. C.

  10. Inefficacy of osmotic backwash induced by sodium chloride salt solution in controlling SWRO membrane fouling

    National Research Council Canada - National Science Library

    Farooque, A Mohammed; Al-Jeshi, Subhi; Saeed, Mohamed O; Alreweli, Ali

    2014-01-01

    ...) concentration solution on feed side of seawater reverse osmosis (SWRO) membranes, online and offline, in controlling membrane fouling and therefore minimizing/eliminating the need for chemical cleaning...

  11. Synergic Mechanism of an Organic Corrosion Inhibitor for Preventing Carbon Steel Corrosion in Chloride Solution

    Institute of Scientific and Technical Information of China (English)

    LIU Zhiyong; YU Lei; LI Qingzhong

    2015-01-01

    The inhibition effect of dimethylethanolamine (DMEA) and its composite with carboxylic acid was studied with the electrochemical tests. The experimental results indicate that DMEA is not a good inhibitor but the composite of DMEA with caprylic acid exhibits excellent inhibiting efficiency. The synergic mechanism of the organic corrosion inhibitors (OCIs) was studied with quantum chemical calculations. It is found that the DMEA forms a quaternary ammonium salt with the proton in carboxylic acid, and a cyclic complex formed between the salt and Fe may be responsible for the enhancement of inhibiting efficiency. The possible hydrogen bond formed between DMEA and carboxylic acid is not enough for the inhibiting effect. This work is helpful to proposing theoretical interpretation as well as developing a functional organic inhibitor to improve the durability of reinforced concrete contaminated with chloride.

  12. Application of the quasi-random lattice model to rare-earth halide solutions for the computation of their osmotic and mean activity coefficients

    Institute of Scientific and Technical Information of China (English)

    Elsa Moggia

    2014-01-01

    This work dealt with the computation of the mean activity coefficients of rare-earth halide aqueous solutions at 25°C, by means of the Quasi Random Lattice (QRL) model. The osmotic coefficients were then calculated consistently, through the integration of the Gibbs-Duhem equation. Using of QRL was mainly motivated by its dependence on one parameter, given in the form of an elec-trolyte-dependent concentration, which was also the highest concentration at which the model could be applied. For all the electrolyte solutions here considered, this parameter was experimentally known and ranged from 1.5 to 2.2 mol/kg, at 25 °C. Accordingly, rare-earth halide concentrations from strong dilution up to 2 mol/kg about could be considered without need for best-fit treatment in order to compute their osmotic and mean activity coefficients. The experimental knowledge about the parameter was an advantageous fea-ture of QRL compared to existing literature models. Following a trend already observed with low charge electrolytes, a satisfactory agreement was obtained with the experimental values for all the investigated rare-earth chlorides and bromides. For the sake of com-pactness, in this work the considered rare-earth halides were all belonging to the P63/m space group in their crystalline (anhydrous) form.

  13. Prediction for pitting corrosion of AISI type 403 stainless steel in chloride-containing borate buffer solution

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Yancheng [Pennsylvania State Univ. (United States); Macdonald, D.D. [Pennsylvania State Univ. (United States). Center for Electrochemical Science and Technology; Urquidi-Macdonald, M. [Pennsylvania State Univ. (United States). Engineering Science and Mechanics; Engelhardt, G.R. [OLI Systems, Inc. (United States); Dooley, R.B. [Electric Power Research Inst., Palo Alto, CA (United States). Materials and Chemistry Performance Dept.

    2007-07-15

    The prediction of pitting corrosion damage on low-pressure steam turbine (LPST) blade surfaces has been investigated experimentally and the results have been interpreted in terms of the Point Defect Model (PDM) for passivity breakdown and the nucleation of pits. Experimental relationships between the critical breakdown potential (Vc) and the chloride activity aCl- and pH have demonstrated the applicability of the PDM for describing passivity breakdown on AISI Type 403 stainless steel (SS), a commonly employed blade alloy in LPSTs, in chloride-containing borate buffer solutions. The model parameter values, as determined by optimization of the PDM on passivity breakdown data, may be used to predict the nucleation and accumulation of pitting damage on LPST blades under simulated turbine shutdown conditions. In order to evaluate the predictions, integral damage functions (IDFs) and extreme value distributions in pit depth have been measured on samples taken from failed blades recovered from the field (Texas Genco). These data are being used to test the predictions of Damage Function Analysis (DFA), which is based on the PDM and on deterministic models for pit growth and delayed repassivation. However, the success of this analysis critically depends on our ability to define the corrosion evolutionary path. (orig.)

  14. Sorption recovery of copper (II and zinc (II from chloride aqueous solutions

    Directory of Open Access Journals (Sweden)

    Kononova Olga N.

    2014-01-01

    Full Text Available The present investigation is devoted to simultaneous sorption recovery of copper (II and zinc (II ions on some commercial anion exchangers with different physical-chemical properties. The initial concentrations of zinc and copper were 1-3 mmol L-1 and the recovery was carried out in 0.01 M and 2 M hydrochloric acid solutions. It was shown that the investigated anion exchangers possess good sorption and kinetic properties. After the recovery of copper and zinc from strong acidic solutions, their selective elution was carried out by means of 2 M hydrochloric acid solution (zinc recovery and 2 M ammonia solution (copper recovery. In weak acidic solutions, copper and zinc were separated during sorption, as zinc sorption did not proceed in this case. The subsequent copper (II elution was carried out by 2 M ammonia solution. The anion exchangers Purolite S985, Purolite A500 and AM-2B can be recommended for zinc and copper recovery from acidic industrial solutions and waste water.

  15. A potential model for sodium chloride solutions based on the TIP4P/2005 water model

    Science.gov (United States)

    Benavides, A. L.; Portillo, M. A.; Chamorro, V. C.; Espinosa, J. R.; Abascal, J. L. F.; Vega, C.

    2017-09-01

    Despite considerable efforts over more than two decades, our knowledge of the interactions in electrolyte solutions is not yet satisfactory. Not even one of the most simple and important aqueous solutions, NaCl(aq), escapes this assertion. A requisite for the development of a force field for any water solution is the availability of a good model for water. Despite the fact that TIP4P/2005 seems to fulfill the requirement, little work has been devoted to build a force field based on TIP4P/2005. In this work, we try to fill this gap for NaCl(aq). After unsuccessful attempts to produce accurate predictions for a wide range of properties using unity ionic charges, we decided to follow recent suggestions indicating that the charges should be scaled in the ionic solution. In this way, we have been able to develop a satisfactory non-polarizable force field for NaCl(aq). We evaluate a number of thermodynamic properties of the solution (equation of state, maximum in density, enthalpies of solution, activity coefficients, radial distribution functions, solubility, surface tension, diffusion coefficients, and viscosity). Overall the results for the solution are very good. An important achievement of our model is that it also accounts for the dynamical properties of the solution, a test for which the force fields so far proposed failed. The same is true for the solubility and for the maximum in density where the model describes the experimental results almost quantitatively. The price to pay is that the model is not so good at describing NaCl in the solid phase, although the results for several properties (density and melting temperature) are still acceptable. We conclude that the scaling of the charges improves the overall description of NaCl aqueous solutions when the polarization is not included.

  16. Corrosion Behavior of Alloy 22 in Chloride Solutions Containing Organic Acids

    Energy Technology Data Exchange (ETDEWEB)

    Carranza, R M; Giordano, C M; Rodr?guez, M A; Rebak, R B

    2005-11-04

    Alloy 22 (N06022) is a nickel based alloy containing alloying elements such as chromium, molybdenum and tungsten. It is highly corrosion resistant both under reducing and under oxidizing conditions. Electrochemical studies such as electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. Tests were also carried out in NaCl solutions containing oxalic acid or acetic acid. It is shown that the corrosion rate of Alloy 22 was higher in a solution containing oxalic acid than in a solution of the same pH acidified with HCl. Acetic acid was not corrosive to Alloy 22. The corrosivity of oxalic acid was attributed to its capacity to form stable complex species with metallic cations from Alloy 22.

  17. Comparative inflammatory effect of antiseptic irrigating solutions against conventional irrigation with sodium chloride in rats.

    OpenAIRE

    Rodríguez Alfaro, Miguel; Profesor Asociado del Departamento Académico de Ciencias Básicas de la Facultad de Odontología de la UNMSM.; Chumpitaz Cerrate, Víctor; Profesor Auxiliar del Departamento Académico de Ciencias Básicas de la Facultad de Odontología de la UNMSM.; Burga Sánchez, Jonny; Profesor Auxiliar del Departamento Académico de Ciencias Básicas de la Facultad de Medicina de la UCSUR.; Arroyo Acevedo, Jorge; Profesor Principal del Departamento Académico de Ciencias Básicas de la Facultad de Medicina de la UNMSM.; Ramón Rosales, Jorge; Profesor Auxiliar del departamento Académico de Ciencias Básicas de la Facultad de Estomatología de la UCSUR.; Aguirre Siancas, Elías; Profesor Auxiliar del Departamento Académico de Ciencias Básicas de la Facultad de Odontología de la UNMSM.; Cabrejos Álvarez, José; Profesor de la Catedra de Cirugia Bucal y Máxilofacial de la Facultad de Estomatología de la UIGV.; Zegarra Cuya, Juan; Ex-Profesor del Departamento Académico de Ciencias Básicas de la Facultad de Odontología de la UNMSM.

    2014-01-01

    The aim of this study was to demonstrate that the use of irrigating solutions in surgical procedures does not alter both inflammation processes and tissue repair. Four (04) groups were formed containing 15 rats each. After being dosed with general anaesthesia, they underwent osteotomy in the tibia with tungsten carbide burs and irrigation for 15 seconds, using the following solutions in each group: A) 0,12 % chlorhexidine with cetylpyridinium 0,05 %, B) 0,12 % chlorhexidine with aspartame; C)...

  18. ZnO Nanorods via Spray Deposition of Solutions Containing Zinc Chloride and Thiocarbamide

    Directory of Open Access Journals (Sweden)

    Dedova Tatjana

    2007-01-01

    Full Text Available AbstractIn this work we present the results on formation of ZnO nanorods prepared by spray of aqueous solutions containing ZnCl2and thiocarbamide (tu at different molar ratios. It has been observed that addition of thiocarbamide into the spray solution has great impact on the size, shape and phase composition of the ZnO crystals. Obtained layers were characterized by scanning electron microscopy (SEM equipped with energy selected backscattered electron detection system (ESB, X-ray diffraction (XRD and photoluminescence spectroscopy (PL. Small addition of thiocarbamide into ZnCl2solution (ZnCl2:tu = 1:0.25 supports development of significantly thinner ZnO nanorods with higher aspect ratio compared to those obtained from ZnCl2solution. Diameter of ZnO rods decreases from 270 to 100 nm and aspect ratio increases from ∼2.5 to 12 spraying ZnCl2and ZnCl2:tu solutions, respectively. According to XRD, well crystallized (002 orientated pure wurtzite ZnO crystals have been formed. However, tiny ‘spot’—like formations of ZnS were detected on the side planes of hexagonal rods prepared from the thiocarbamide containing solutions. Being adsorbed on the side facets of the crystals ZnS inhibits width growth and promotes longitudinalc-axis growth.

  19. Effect of nickel content on the electrochemical behavior of Cu-Al-Ni alloys in chloride free neutral solutions

    Energy Technology Data Exchange (ETDEWEB)

    Badawy, W.A., E-mail: wbadawy50@hotmail.co [Chemistry Department, Faculty of Science, Cairo University, 12 613 Giza (Egypt); El-Rabiee, M.M.; Helal, N.H.; Nady, H. [Chemistry Department, Faculty of Science, Fayoum University, Fayoum (Egypt)

    2010-12-30

    The electrochemical behavior of Cu-Al-Ni alloys in chloride free neutral solutions was investigated. The effect of Ni content on the corrosion resistance of the alloys was examined and evaluated. Conventional electrochemical techniques and electrochemical impedance spectroscopy, EIS, have been used. Potentiodynamic measurements revealed that the increase in the Ni content decreases the stability of the Cu-Al-Ni alloys. The polarization measurements were confirmed by EIS experiments. The morphology of the alloy surface was investigated by scanning electron microscopy, SEM, and surface analysis was made by energy dispersive X-ray technique. The experimental impedance data were fitted to theoretical data according to a proposed equivalent circuit model representing the electrode/electrolyte interface. The results of these experiments are discussed in reference to the potential-pH (Pourbaix) diagrams of the alloying elements.

  20. The phosphine oxides Cyanex 921 and Cyanex 923 as carriers for facilitated transport of chromium (VI)-chloride aqueous solutions.

    Science.gov (United States)

    Alguacil, Francisco José; López-Delgado, Aurora; Alonso, Manuel; Sastre, Ana Maria

    2004-11-01

    The behaviour of the phosphine oxides Cyanex 921 and Cyanex 923 in the facilitated transport of chromium (VI) from chloride solutions is described. Transport is studied as a function of several variables such as stirring speeds of the aqueous phases, membrane phase diluent, hydrochloric acid concentration in the source phase and chromium and carrier concentrations. The separation of chromium (VI) from other metals presented in the source phase as well as the behaviour of phosphine oxides with respect to other neutral organophosphorous derivatives (tri-n-butylphosphate (TBP) and dibutyl butylphosphonate (DBBP)) are also investigated. Moreover, by using hydrazine sulphate in the receiving phase, Cr(VI) is immediately reduced to the less toxic Cr(III).

  1. Blue-Green Color Tunable Solution Processable Organolead Chloride-Bromide Mixed Halide Perovskites for Optoelectronic Applications.

    Science.gov (United States)

    Sadhanala, Aditya; Ahmad, Shahab; Zhao, Baodan; Giesbrecht, Nadja; Pearce, Phoebe M; Deschler, Felix; Hoye, Robert L Z; Gödel, Karl C; Bein, Thomas; Docampo, Pablo; Dutton, Siân E; De Volder, Michael F L; Friend, Richard H

    2015-09-09

    Solution-processed organo-lead halide perovskites are produced with sharp, color-pure electroluminescence that can be tuned from blue to green region of visible spectrum (425-570 nm). This was accomplished by controlling the halide composition of CH3NH3Pb(BrxCl1-x)3 [0 ≤ x ≤ 1] perovskites. The bandgap and lattice parameters change monotonically with composition. The films possess remarkably sharp band edges and a clean bandgap, with a single optically active phase. These chloride-bromide perovskites can potentially be used in optoelectronic devices like solar cells and light emitting diodes (LEDs). Here we demonstrate high color-purity, tunable LEDs with narrow emission full width at half maxima (FWHM) and low turn on voltages using thin-films of these perovskite materials, including a blue CH3NH3PbCl3 perovskite LED with a narrow emission FWHM of 5 nm.

  2. The extraction of zinc from chloride solutions using dibutyl butylphosphonate (DBBP in Exxsol D100

    Directory of Open Access Journals (Sweden)

    Alguacil, F. J.

    1999-08-01

    Full Text Available The reaction of zinc chloride with dibutyl butylphosphonate in Exxsol D100 has been studied. The distribution coefficient of zinc is independent of equilibrium pH, thus, suggesting a solvation extraction reaction. Experimental data indicate that this reaction is exothermic (AH°=-28.4 kJ/mol. Slope analysis for the system at various DBBP concentrations reveals the formation in the loaded organic phases of species which probable 1:2 (Zn:DBBP stoichiometries. This was confirmed by results obtained at full DBBP Zn-loading capacity. The stoichiometric factor of water in the extraction reaction is found to be 4, whereas experimental data also indicated that two chloride ions are involved for each metal extracted, resulting in a ZnCl2∙2L∙4H2O stoichiometry (L represents the extractant.

    Se estudia la extracción de zinc, en medio cloruro, con el dibutil butilfosfonato disuelto en Exxsol D100. El coeficiente de distribución del metal es independiente del pH de equilibrio de la fase acuosa, lo que sugiere un mecanismo de extracción por solvatación. Los resultados experimentales indican que la reacción es exotérmica (AH°=-28,4 kJ/mol. Mediante análisis de la pendiente obtenida cuando se emplean distintas concentraciones de DBBP en la extracción de zinc se deduce la formación de una especie con estequiometría 1:2 (Zn:DBBP en la fase orgánica. Este hecho se confirma con los resultados obtenidos cuando se satura completamente la fase orgánica. En esta fase, el factor estequiométrico para el agua es 4, mientras que para el ion cloruro es 2, por lo que la especie extraída tiene una estequiometría final representada por ZnCl2∙2L∙4H2O (L representa al agente de extracción.

  3. Red-emitting alkaline-earth rare-earth pentaoxometallates powders prepared by metal carboxylates solution

    Indian Academy of Sciences (India)

    Kyu-Seog Hwang; Sung-Dae Kim; Seung Hwangbo; Jin-Tae Kim

    2013-06-01

    Moisture-insensitive metal carboxylates that are mostly liquids at room temperature have been first applied to the preparation of strontium europium aluminate (Sr2EuAlO5) powders for red-emitting phosphor under near ultraviolet radiation. Strontium naphthenate, aluminium-2-ethylhexanoate and europium-2-ethylhexanoate were dissolved with toluene to prepare starting solution. Precursor pyrolyzed at 500 °C for 240 min was finally annealed at 900–1200 °C for 240 min in Ar. X-ray diffraction analysis, field emission–scanning electron microscope and fluorescent spectrophotometer were used to evaluate structural and optical properties. For the 1000 °C-annealed powders with regular shape and narrow size distribution confirmed by FE–SEM observation, strong red emission at 615nm under the excitation of 395nm maximum was reached, then the higher annealed samples at above 1100 °C gave the lower emission intensities.

  4. Removal of lead from aqueous solutions with a treated spent bleaching earth.

    Science.gov (United States)

    Mana, Mohamed; Ouali, Mohand Said; Lindheimer, Marc; Menorval, Louis Charles de

    2008-11-30

    A spent bleaching earth from an edible oil refinery has been treated by impregnation with a normal sodium hydroxide solution followed by mild thermal treatment (100 degrees C). The obtained material (TSBE) was washed, dried and characterized by X-ray diffraction, FTIR, SEM, BET and thermal analysis. The clay structure was not apparently affected by the treatment and the impregnated organic matter was quantitatively removed. We have investigated the sorption of lead on this material, the spent bleaching earth (SBE) and the virgin bleaching earth (VBE). The kinetic results fit the pseudo second-order kinetic model and the Weber & Morris, intraparticle diffusion model. The pH had effect on the sorption efficiency. The sorption isotherms followed the Langmuir model for various sorbent concentrations with good values of determination coefficient. A comparison between the results obtained with this material and those of the literature highlighted a good removal capacity of the treated spent bleaching earth at low cost.

  5. Removal of lead from aqueous solutions with a treated spent bleaching earth

    Energy Technology Data Exchange (ETDEWEB)

    Mana, Mohamed [Laboratoire de Valorisation des Materiaux, University of Mostaganem, B.P. 227, Mostaganem R.P. (Algeria); Ouali, Mohand Said [Laboratoire de Valorisation des Materiaux, University of Mostaganem, B.P. 227, Mostaganem R.P. (Algeria)], E-mail: ouali@univ-mosta.dz; Lindheimer, Marc; Menorval, Louis Charles de [Institut Charles Gerhardt Montpellier, UMR 5253 Universite Montpellier 2 Case Courrier 1700 Place Eugene Bataillon 34095 Montpellier Cedex 5 (France)

    2008-11-30

    A spent bleaching earth from an edible oil refinery has been treated by impregnation with a normal sodium hydroxide solution followed by mild thermal treatment (100 deg. C). The obtained material (TSBE) was washed, dried and characterized by X-ray diffraction, FTIR, SEM, BET and thermal analysis. The clay structure was not apparently affected by the treatment and the impregnated organic matter was quantitatively removed. We have investigated the sorption of lead on this material, the spent bleaching earth (SBE) and the virgin bleaching earth (VBE). The kinetic results fit the pseudo second-order kinetic model and the Weber and Morris, intraparticle diffusion model. The pH had effect on the sorption efficiency. The sorption isotherms followed the Langmuir model for various sorbent concentrations with good values of determination coefficient. A comparison between the results obtained with this material and those of the literature highlighted a good removal capacity of the treated spent bleaching earth at low cost.

  6. Pain and swelling after periapical surgery related to the hemostatic agent used: Anesthetic solution with vasoconstrictor or aluminum chloride

    Science.gov (United States)

    Maestre-Ferrín, Laura; Peñarrocha-Oltra, David; Gay-Escoda, Cosme; von-Arx, Tomas; Peñarrocha-Diago, Miguel

    2012-01-01

    Objective: To assess pain and swelling in the first 7 days after periapical surgery and their relationship with the agent used for bleeding control. Study Design: A prospective study was conducted between October 2006 and March 2009. Patients subjected to root surgery, who completed the questionnaire and who consented to the postoperative instructions were included in the study. The subjects were divided into two groups according to the hemostatic agent used: A) gauze impregnated with anesthetic solution with vasoconstrictor; or B) aluminum chloride. The patients were administered a questionnaire, and were asked to record the severity of their pain and swelling on a plain horizontal visual analog scale (VAS). Data were recorded by the patients on the first 7 postoperative days. In addition, the patients were asked to record analgesic consumption. Results: A total of 76 questionnaires (34 in group A and 42 in group B) were taken to be correctly completed. Pain was reported to be most intense two hours after surgery. At this point 52.6% of the patients had no pain. Seventy-five percent of the patients consumed analgesics in the first 24 hours. There were no significant differences between the two groups in terms of the intensity of pain or in the consumption of analgesics. Swelling reached its maximum peak on the second day; at this point, 60.6% of the patients suffered mild or moderate swelling. The Expasyl™ group showed significantly greater swelling than the gauzes group. Conclusion: The type of hemostatic agent used did not influence either the degree of pain or the need for analgesia among the patients in this study. However, the patients belonging to the Expasyl™ group suffered greater swelling than the patients treated with gauzes impregnated with anesthetic solution with vasoconstrictor. Key words:Hemostasis, periradicular surgery, aluminum chloride, pain, swelling. PMID:22322510

  7. An electrochemical investigation of the corrosion behavior of aluminum alloys in chloride containing solutions; Investigacao eletroquimica da corrosao de ligas de aluminio em solucoes contendo cloretos

    Energy Technology Data Exchange (ETDEWEB)

    Campos Filho, Jorge Eustaquio de [Minas Gerais Univ., Belo Horizonte, MG (Brazil). Escola de Engenharia. Dept. de Engenharia Quimica]. E-mail: jorgecamposfilho@yahoo.com.br; Neves, Celia de Figueiredo Cordeiro; Campos, Wagner Reis da Costa; Moreira, Marcilio Soares [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), Belo Horizonte, MG (Brazil)]. E-mail: caf@cdtn.br; wrcc@cdtn.br; msm@cdtn.br

    2005-07-01

    Aluminum alloys have been used as cladding materials for nuclear fuel in research reactors due to its corrosion resistance. Aluminum owes its good corrosion resistance to a protective barrier oxide film formed and strongly bonded to its surface. In pool type TRIGA IPR-R1 reactor, located at Centro de Desenvolvimento da Tecnologia Nuclear in Belo Horizonte, previous immersion coupon tests revealed that aluminum alloys suffer from pitting corrosion, in spite of high quality of water control. Corrosion attack is initiated by breaking the protective oxide film on aluminum alloy surface. Chloride ions can break this oxide film and stimulate metal dissolution. In this study the aluminum alloys 1050, 5052 and 6061 were used to evaluate their corrosion behavior in chloride containing solutions. The electrochemical techniques used were potentiodynamic anodic polarization and cyclic polarization. Results showed that aluminum alloys 5052 and 6061 present similar corrosion resistance in low chloride solutions (0,1 ppm NaCl) and in reactor water but both alloys are less resistant in high chloride solution (1 ppm NaCl). Aluminum alloy 1050 presented similar behavior in the three electrolytes used, regarding to pitting corrosion, indicating that the concentration of the chloride ions was not the only variable to influence its corrosion susceptibility. (author)

  8. Evaluation of the cytotoxic effects of ophthalmic solutions containing benzalkonium chloride on corneal epithelium using an organotypic 3-D model

    Science.gov (United States)

    Khoh-Reiter, Su; Jessen, Bart A

    2009-01-01

    Background Benzalkonium chloride (BAC) is a common preservative used in ophthalmic solutions. The aim of this study was to compare the cytotoxic effects of BAC-containing ophthalmic solutions with a BAC-free ophthalmic solution using an organotypic 3-dimensional (3-D) corneal epithelial model and to determine the effects of latanoprost ophthalmic solution and its BAC-containing vehicle on corneal thickness in a monkey model. Methods The cytotoxicity of commercially available BAC-containing ophthalmic formulations of latanoprost (0.02% BAC) and olopatadine (0.01% BAC) was compared to that of BAC-free travoprost and saline in a corneal organotypic 3-D model using incubation times of 10 and 25 minutes. To compare the extent of differentiation of 3-D corneal cultures to monolayer transformed human corneal epithelial (HCE-T) cell cultures, expression levels (mRNA and protein) of the corneal markers epidermal growth factor receptor, transglutaminase 1 and involucrin were quantified. Finally, latanoprost ophthalmic solution or its vehicle was administered at suprapharmacologic doses (two 30 μL drops twice daily in 1 eye for 1 year) in monkey eyes, and corneal pachymetry was performed at baseline and at weeks 4, 13, 26 and 52. Results In the 3-D corneal epithelial culture assays, there were no significant differences in cytotoxicity between the BAC-containing latanoprost and olopatadine ophthalmic solutions and BAC-free travoprost ophthalmic solution at either the 10- or 25-minute time points. The 3-D cultures expressed higher levels of corneal epithelial markers than the HCE-T monolayers, indicating a greater degree of differentiation. There were no significant differences between the corneal thickness of monkey eyes treated with latanoprost ophthalmic solution or its vehicle (both containing 0.02% BAC) and untreated eyes. Conclusion The lack of cytotoxicity demonstrated in 3-D corneal cultures and in monkey studies suggests that the levels of BAC contained in ophthalmic

  9. Evaluation of the cytotoxic effects of ophthalmic solutions containing benzalkonium chloride on corneal epithelium using an organotypic 3-D model

    Directory of Open Access Journals (Sweden)

    Jessen Bart A

    2009-07-01

    Full Text Available Abstract Background Benzalkonium chloride (BAC is a common preservative used in ophthalmic solutions. The aim of this study was to compare the cytotoxic effects of BAC-containing ophthalmic solutions with a BAC-free ophthalmic solution using an organotypic 3-dimensional (3-D corneal epithelial model and to determine the effects of latanoprost ophthalmic solution and its BAC-containing vehicle on corneal thickness in a monkey model. Methods The cytotoxicity of commercially available BAC-containing ophthalmic formulations of latanoprost (0.02% BAC and olopatadine (0.01% BAC was compared to that of BAC-free travoprost and saline in a corneal organotypic 3-D model using incubation times of 10 and 25 minutes. To compare the extent of differentiation of 3-D corneal cultures to monolayer transformed human corneal epithelial (HCE-T cell cultures, expression levels (mRNA and protein of the corneal markers epidermal growth factor receptor, transglutaminase 1 and involucrin were quantified. Finally, latanoprost ophthalmic solution or its vehicle was administered at suprapharmacologic doses (two 30 μL drops twice daily in 1 eye for 1 year in monkey eyes, and corneal pachymetry was performed at baseline and at weeks 4, 13, 26 and 52. Results In the 3-D corneal epithelial culture assays, there were no significant differences in cytotoxicity between the BAC-containing latanoprost and olopatadine ophthalmic solutions and BAC-free travoprost ophthalmic solution at either the 10- or 25-minute time points. The 3-D cultures expressed higher levels of corneal epithelial markers than the HCE-T monolayers, indicating a greater degree of differentiation. There were no significant differences between the corneal thickness of monkey eyes treated with latanoprost ophthalmic solution or its vehicle (both containing 0.02% BAC and untreated eyes. Conclusion The lack of cytotoxicity demonstrated in 3-D corneal cultures and in monkey studies suggests that the levels of BAC

  10. Cooling and Freezing Behaviors of Aqueous Sodium Chloride Solution in a Closed Rectangular Container

    Science.gov (United States)

    Narumi, Akira; Kashiwagi, Takao; Nakane, Ichirou

    This paper investigates cooling and freezing behaviors of NaCl aqueous solution in a rectangular container equipped with horizontal partitions of micro porous film in order to determine the mechanisms of heat and mass transfer through cell wall for the purpose of freezing food. For comparison, experiments were performed using partitions of copper plate, no partition, and water. These processes were visualized and measured using real-time laser holographic interferometry. It was found that there was very little difference in the cooling process due to partitions, but that there were significant differences in freezing process when NaCl aqueous solution is used.

  11. Direct spectrophotometric determination of Nd and Er in mixed rare earths with 8-hydroxyquinoline-5-sulphonic acid and cetylpyridinium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Shifu Zhou; Naixing Wang (Shandong Univ., Jinan (China). Dept. of Chemistry)

    1990-03-01

    Neodymium and erbium can form stable ternary complexes with 8-hydroxyquinoline-5-sulphonic acid and cetylpyridinium chloride, but a photometric method based on this does not give high enough sensitivity and is subject to interference by cerium. Use of the third derivative spectra, however, eliminates the interference by cerium and increases the sensitivity. (author).

  12. Determination of Coordination Configuration of Rare Earth Ionswith Aminoacids in Solutions with Cooperative Vibronic Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The use of cooperative vibronic spectroscopy to measure coordination numbers of the ligands surrounding rare earth ions in solutions was proposed and demonstrated. It is shown that the time-resolved cooperative vibronic spectroscopy is a very useful technique for the determination of the ligand type and ligand number for different coordination groups. Coordination configuration of arginine with Tb3+ in solutions with different pH values was studied. It demonstrates that the carboxyl of arginine can replace H2O to coordinate with Tb3+ and the coordination number of carboxyl increases with the increase of pH value of the solutions.

  13. The role of temperature in copper electrocrystallization in ammonia-chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez-Arenas, Jorge [Facultad de Ingenieria, Instituto de Metalurgia, Universidad Autonoma de San Luis Potosi, Av. Sierra Leona 550, Lomas 2a seccion, 78210 San Luis Potosi, S.L.P. (Mexico); Cruz, Roel [Facultad de Ingenieria, Instituto de Metalurgia, Universidad Autonoma de San Luis Potosi, Av. Sierra Leona 550, Lomas 2a seccion, 78210 San Luis Potosi, S.L.P. (Mexico)]. E-mail: rcuz@uaslp.mx; Mendoza-Huizar, Luis H. [Centro de Investigaciones Quimicas, Universidad Autonoma del Estado de Hidalgo, Unidad Universitaria, Km 4.5 Carretera Pachuca-Tulancingo, CP. 42184 Pachuca-Hidalgo (Mexico)

    2006-11-12

    This paper presents the analysis of temperature effect on the copper electrocrystallization process from the stainless steel/Cu(II)-Cu(I)-NH{sub 4}Cl-NH{sub 3}-H{sub 2}O system. Electrochemical techniques and scanning electron microscopy with energy dispersion spectroscopy were employed. An increment in temperature had a favorable effect in increasing the kinetic and nucleation parameters, favoring the copper reduction on the stainless steel substrate. From the chronoamperometric study, it was possible to find the transfer coefficient ({alpha}), which does not have a significant variation with temperature, and the exchange current density (i ) for different temperatures, where a 50.63 kJ/mol value was estimated for the activation energy. The potentiostatic study suggested the presence of two processes involved: an electron transfer reaction and a 3D nucleation-growth process, under combined charge transfer and diffusion limitations. In addition, an important current contribution could be accounted for on the basis of the existence of a capacitive component in the system. This capacitive behavior was associated to the oxide layer (Cr{sub 2}O{sub 3})-chloride interactions on the stainless steel surface. Current transients analyses at different potentials, based on the models of: Milchev (low overpotential), Scharifker-Mostany (SM) and Heermann-Tarallo (HT) (high overpotential) allowed to obtain the values of nucleation parameters, such as: the nucleation rate constant (A), the active nucleation sites number (N ), the stationary nucleation rate (I {sub st} = A x N ) and the nuclei saturation number (N {sub s}). Finally, the deposits obtained were analyzed by SEM, showing an acceptable correlation between the nucleation parameters and morphology of the deposits obtained. An increment in temperature favored the growth of the cluster before the coalescence occurred.

  14. [Adsorption Characteristics of Nitrate and Phosphate from Aqueous Solution on Zirconium-Hexadecyltrimethylammonium Chloride Modified Activated Carbon].

    Science.gov (United States)

    Zheng, Wen-jing; Lin, Jian-wei; Zhan, Yan-hui; Wang, Hong

    2015-06-01

    A novel adsorbent material, i.e., zirconium-cationic surfactant modified activated carbon (ZrSMAC) was prepared by loading zirconium hydroxide and hexadecyltrimethylammonium chloride (CTAC) on activated carbon, and was used as an adsorbent for nitrate and phosphate removal from aqueous solution. The adsorption characteristics of nitrate and phosphate on ZrSMAC from aqueous solution were investigated in batch mode. Results showed that the ZrSMAC was effective for nitrate and phosphate removal from aqueous solution. The pseudo-second-order kinetic model fitted both the nitrate and phosphate kinetic experimental data well. The equilibrium isotherm data of nitrate adsorption onto the ZrSMAC were well fitted to the Langmuir, Dubinin-Radushkevich (D-R) and Freundlich isotherm models. The equilibrium isotherm data of phosphate adsorption onto the ZrSMAC could be described by the Langmuir and,D- R isotherm models. According to the Langmuir isotherm model, the maximum nitrate and phosphate adsorption capacities for the ZrSMAC were 7.58 mg x g(-1) and 10.9 mg x g(-1), respectively. High pH value was unfavorable for nitrate and phosphate adsorption onto the ZrSMAC. The presence of Cl-, HCO3- and SO4(2-) in solution reduced the nitrate and phosphate adsorption capacities for the ZrSMAC. The nitrate adsorption capacity for the ZrSMAC was reduced by the presence of coexisting phosphate in solution, and the phosphate adsorption capacity for the ZrSMAC was also reduced by the presence of coexisting nitrate in solution. About 90% of nitrate adsorbed on the ZrSMAC could be desorbed in 1 mol x L(-1) NaCl solution, and about 78% of phosphate adsorbed on the ZrSMAC could be desorbed in 1 mol x L(-1) NaOH solution. The adsorption mechanism of nitrate on the ZrSMAC included the anion exchange interactions and electrostatic attraction, and the adsorption mechanism of phosphate on the ZrSMAC included the ligand exchange interaction, electrostatic attraction and anion exchange interaction.

  15. Electrochemical Study of Corrosion Behavior of Wrought Stellite Alloys in Sodium Chloride and Green Death Solutions

    Science.gov (United States)

    Zhang, X. Z.; Liu, R.; Chen, K. Y.; Yao, M. X.; Collier, R.

    2015-09-01

    Corrosion behavior of wrought Stellite 6B and Stellite 6K, which have similar chemical composition but contain different carbon content, in 3.5 wt.% NaCl solution and in Green Death solution is investigated using various electrochemical methods, including potentiodynamic polarization, cyclic polarization, and electrochemical impedance spectroscopy (EIS). The obtained potentiodynamic polarization curves, cyclic polarization curves, and EIS spectra for these alloys are in good agreement, showing that Stellite 6K with higher carbon content is easier corroded due to its larger volume fraction of carbides but the Cr2O3 film formed on this alloy is stronger and more stable than that on Stellite 6B. Further immersion tests on these alloys show that Stellite 6K has less resistance to pitting corrosion.

  16. The Interaction of Polycrystalline Copper Films with Dilute Aqueous Solutions of Cupric Chloride

    Science.gov (United States)

    1989-10-01

    in atmosphere has always been of interest because of the extensive use of copper and brass in buildings and statues, for example. A study by Pinnel et...solution and the sample surface layer have been reported with no mention of the microstructure of the copper sample except for a few cases where chemical...used as a substrate when the deposited film will be removed for mechanical testing. In this case , the copper film was removed prior to characterization

  17. Sorption recovery of platinum (II, IV in presence of copper (II and zinc (II from chloride solutions

    Directory of Open Access Journals (Sweden)

    Kononova Olga N.

    2015-01-01

    Full Text Available The sorption preconcentration of platinum (II, IV ions was investigated in presence of accompanying copper (II and zinc (II ions from chloride solutions on the new ion exchangers CYBBER (Russia, previously unexplored. The initial concentrations of platinum and accompanying ions were 0.25 mmol L-1 and 2.0 mmol L-1, respectively, and the acidity of medium was 0.001 - 4.0 mol L-1. It was shown that the resins investigated - strong and weak basic anion exchangers as well as chelate ion exchangers - possess good sorption and kinetic properties. The simultaneous sorption of investigated ions results in the complete recovery of platinum, while the non-ferrous metal ions are sorbed at less than 20%. Followed by the selective elution of platinum by thiourea (80 g L-1 solution in 0.3 M H2SO4, the quantitative isolation of platinum was achieved (more than 90%. Therefore, the studied ion exchangers can be recommended for recovery and separation of Pt(II,IV, Cu(II and Zn(II ions.

  18. Solute transport in streams of varying morphology inferred from a high resolution network of potentiometric wireless chloride sensors

    Science.gov (United States)

    Klaus, Julian; Smettem, Keith; Pfister, Laurent; Harris, Nick

    2017-04-01

    There is ongoing interest in understanding and quantifying the travel times and dispersion of solutes moving through stream environments, including the hyporheic zone and/or in-channel dead zones where retention affects biogeochemical cycling processes that are critical to stream ecosystem functioning. Modelling these transport and retention processes requires acquisition of tracer data from injection experiments where the concentrations are recorded downstream. Such experiments are often time consuming and costly, which may be the reason many modelling studies of chemical transport have tended to rely on relatively few well documented field case studies. This leads to the need of fast and cheap distributed sensor arrays that respond instantly and record chemical transport at points of interest on timescales of seconds at various locations in the stream environment. To tackle this challenge we present data from several tracer experiments carried out in the Attert river catchment in Luxembourg employing low-cost (in the order of a euro per sensor) potentiometric chloride sensors in a distributed array. We injected NaCl under various baseflow conditions in streams of different morphologies and observed solute transport at various distances and locations. This data is used to benchmark the sensors to data obtained from more expensive electrical conductivity meters. Furthermore, the data allowed spatial resolution of hydrodynamic mixing processes and identification of chemical 'dead zones' in the study reaches.

  19. Study of benzotriazole as corrosion inhibitors of carbon steel in chloride solution containing hydrogen sulfide using electrochemical impedance spectroscopy (EIS)

    Energy Technology Data Exchange (ETDEWEB)

    Solehudin, Agus, E-mail: asolehudin@upi.edu [Department of Mechanical Engineering Education, Indonesia University of Education (UPI), Bandung, West Java (Indonesia); Nurdin, Isdiriayani [Department of Chemical Engineering, Bandung Institute of Technology, Bandung, West Java (Indonesia)

    2014-03-24

    Corrosion and inhibition studies on API 5LX65 carbon steel in chloride solution containing various concentrations of benzotriazole has been conducted at temperature of 70°C using Electrochemical Impedance Spectroscopy (EIS). Corroded carbon steel surface with and without inhibitor have been observed using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Energy Dispersive Spectroscopy (EDS). The objectives of this research are to study the performance of benzotriazole as corrosion inhibitors. The experimental results of carbon steel corrosion in 3.5% NaCl solution containing 500 mg/l H{sub 2}S at different BTAH concentrations showed that corrosion rate of carbon steel decreases with increasing of BTAH concentrations from 0 to 10 mmol/l. The inhibition efficiency of BTAH was found to be affected by its concentration. The optimum efficiency obtained of BTAH is 93% at concentration of 5 mmol/l. The result of XRD and EDS analysis reveal the iron sulfide (FeS) formation on corroded carbon steel surface without inhibitor. The EDS spectrum show the Nitrogen (N) bond on carbon steel surface inhibited by BTAH.

  20. Study of benzotriazole as corrosion inhibitors of carbon steel in chloride solution containing hydrogen sulfide using electrochemical impedance spectroscopy (EIS)

    Science.gov (United States)

    Solehudin, Agus; Nurdin, Isdiriayani

    2014-03-01

    Corrosion and inhibition studies on API 5LX65 carbon steel in chloride solution containing various concentrations of benzotriazole has been conducted at temperature of 70°C using Electrochemical Impedance Spectroscopy (EIS). Corroded carbon steel surface with and without inhibitor have been observed using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Energy Dispersive Spectroscopy (EDS). The objectives of this research are to study the performance of benzotriazole as corrosion inhibitors. The experimental results of carbon steel corrosion in 3.5% NaCl solution containing 500 mg/l H2S at different BTAH concentrations showed that corrosion rate of carbon steel decreases with increasing of BTAH concentrations from 0 to 10 mmol/l. The inhibition efficiency of BTAH was found to be affected by its concentration. The optimum efficiency obtained of BTAH is 93% at concentration of 5 mmol/l. The result of XRD and EDS analysis reveal the iron sulfide (FeS) formation on corroded carbon steel surface without inhibitor. The EDS spectrum show the Nitrogen (N) bond on carbon steel surface inhibited by BTAH.

  1. A comparative study on the electrochemical corrosion behavior of iron and X-65 steel in 4.0 wt % sodium chloride solution after different exposure intervals.

    Science.gov (United States)

    Sherif, El-Sayed M

    2014-07-09

    In this work, the results obtained from studying the anodic dissolution of pure iron and API X-65 5L pipeline steel after 40 min and 12 h exposure period in 4.0 wt % NaCl solutions at room temperature were reported. Potential-time, electrochemical impedance spectroscopy, potentiodynamic polarization, and chronoamperometric current-time at constant potential techniques were employed. It has been found that the iron electrode corrodes in the chloride test solutions faster than the API X-65 5L steel does under the same conditions. Increasing the exposure period for the electrodes from 40 min to 12 h showed a significant reduction in the corrosion parameters for both iron and steel in the 4.0 wt % NaCl solution. Results together confirmed clearly that the X-65 steel is superior to iron against corrosion in sodium chloride solutions.

  2. Standard test method for evaluating stress-corrosion cracking of stainless alloys with different nickel content in boiling acidified sodium chloride solution

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This test method describes a procedure for conducting stress-corrosion cracking tests in an acidified boiling sodium chloride solution. This test method is performed in 25% (by mass ) sodium chloride acidified to pH 1.5 with phosphoric acid. This test method is concerned primarily with the test solution and glassware, although a specific style of U-bend test specimen is suggested. 1.2 This test method is designed to provide better correlation with chemical process industry experience for stainless steels than the more severe boiling magnesium chloride test of Practice G36. Some stainless steels which have provided satisfactory service in many environments readily crack in Practice G36, but have not cracked during interlaboratory testing using this sodium chloride test method. 1.3 This boiling sodium chloride test method was used in an interlaboratory test program to evaluate wrought stainless steels, including duplex (ferrite-austenite) stainless and an alloy with up to about 33% nickel. It may also b...

  3. Inefficacy of osmotic backwash induced by sodium chloride salt solution in controlling SWRO membrane fouling

    Science.gov (United States)

    Farooque, A. Mohammed; Al-Jeshi, Subhi; Saeed, Mohamed O.; Alreweli, Ali

    2014-12-01

    A study was conducted to evaluate the efficacy of osmotic backwash induced by high salt (NaCl) concentration solution on feed side of seawater reverse osmosis (SWRO) membranes, online and offline, in controlling membrane fouling and therefore minimizing/eliminating the need for chemical cleaning. SWRO membranes were deliberately fouled by feeding seawater from an open intake located on the Arabian Gulf Coast without dosing chemicals. The fouled membranes were subjected to offline cleaning with the salt solution of up to 25 % concentration. Despite the partial removal of foulants from the membrane surface, SWRO membrane performance could not be restored, indicating the ineffectiveness of osmotic backwash in aiding offline salt cleaning. Similarly, online osmotic backwash was found to be not only ineffective in removing foulants from membrane surfaces but actually increased the fouling rate, as indicated by faster fouling rates compared to other cases. Although the driving force required for the osmotic backwash existed, the generated back flow proved to be insufficient to detach foulants from membrane surfaces. During the study period, the average SWRO membrane flux was maintained between 19 and 23 LMH, whereas the average generated back flow flux by high salt concentration solution was only 11 LMH, which was not adequate to remove foulants from membrane surfaces. Moreover, it seems that the membrane configuration as well as inherent microstructure of SWRO membrane places certain constraints on the osmotic backwash process and renders osmotic backwash ineffective in tackling SWRO membrane fouling. Hence, chemical cleaning is essential to restore SWRO membrane performance whenever fouling occurs, and the use of highly concentrated salt solution does not have any significant benefit. Membrane autopsy revealed only an insignificant accumulation of biofouling layer despite the absence of disinfection. However, it was shown that culturable biofilm bacteria species

  4. Material Solutions to Mitigate the Alkali Chloride-Induced High Temperature Corrosion

    DEFF Research Database (Denmark)

    Kiamehr, Saeed

    in flowing N2(g)+5%O2(g)+15%H2O(g). Each exposed sample was a mixture of the metal oxide and KCl pressed into a tablet. Samples were examined with X-Ray Diffractometry (XRD) before and after the exposure. In addition, each exposed sample was further studied with Scanning Electron Microscopy (SEM) and Energy...... materials solution TP347HFG in the laboratory exposures. Pure Ni incurred the least amount of damage. Part 3: Performance of aluminum diffusion coatings Among the suitable oxide-forming elements identified in part 1, Al is an obvious choice for further investigations. However, the results in part 2...

  5. La2010: A new orbital solution for the long term motion of the Earth

    CERN Document Server

    Laskar, J; Gastineau, M; Manche, H

    2011-01-01

    We present here a new solution for the astronomical computation of the orbital motion of the Earth spanning from 0 to -250 Myr. The main improvement with respect to the previous numerical solution La2004 (Laskar et al. 2004) is an improved adjustment of the parameters and initial conditions through a ?t over 1 Myr to a special version of the high accurate numerical ephemeris INPOP08 (Fienga et al. 2009). The precession equations have also been entirely revised and are no longer averaged over the orbital motion of the Earth and Moon. This new orbital solution is now valid over more than 50 Myr in the past or in the future with proper phases of the eccentricity variations. Due to chaotic behavior, the precision of the solution decreases rapidly beyond this time span, and we discuss the behavior of various solutions beyond 50 Myr. For paleoclimate calibrations, we provide several di?erent solutions that are all compatible with the most precise planetary ephemeris. We have thus reached the time where geological d...

  6. Inhibitive effect of some thiadiazole derivatives on C-steel corrosion in neutral sodium chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    El-Taib Heakal, F., E-mail: fakihaheakal@yahoo.com [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt); Fouda, A.S. [Chemistry Department, Faculty of Science, El-Mansoura University, El-Mansoura (Egypt); Radwan, M.S. [Petrogulf Misr Company, Maadi, Cairo (Egypt)

    2011-01-01

    Electrochemical techniques were used to investigate the effect of concentration of three new thiadiazole derivatives (I-III) on the corrosion behavior of C-steel in 0.5 M NaCl solution through the analysis of electrochemical measurements including open circuit potential (OCP), Tafel polarization and electrochemical impedance spectroscopy (EIS). Polarization curves showed that the compounds studied act as anodic type inhibitors, where the inhibition efficiency increases with increase in inhibitor concentration and decreases with rise in temperature. An adherent layer of inhibitor molecules on the surface is proposed to account for their inhibitive action in which the organic molecules adsorb on the active anodic sites following Langmuir isotherm. The thermodynamic parameters of adsorption and corrosion processes were determined and discussed. The results also indicated that pitting potential at higher anodic polarization of C-steel in 0.5 M NaCl solution becomes more positive the higher the concentration of the additive, suggesting that these inhibitors acts as retarding catalyst for pitting corrosion. EIS data confirm well the electrochemical dc results and the results are all in good agreement with the calculated quantum chemical HOMO and LUMO energies of the tested molecules, as well as with surface examination via scanning electron microscope.

  7. Selective Separation of Similar Metals in Chloride Solution by Sulfide Precipitation Under Controlled Potential

    Science.gov (United States)

    Liu, Weifeng; Sun, Baiqi; Zhang, Duchao; Chen, Lin; Yang, Tianzu

    2017-08-01

    A new process of sulfide precipitation under controlled potential was proposed to separate selectively similar metals in a Bis(2-ethylhexyl) phosphoric acid (P204) stripping solution of the Co extraction system. Theoretical calculations revealed that Cu2+, Co2+, Zn2+, and Mn2+ could be separated by fractional precipitation with sulfide by controlling the solution potential and pH value simultaneously. The results demonstrated a Cu precipitation ratio reaching 99.9% during sulfide precipitation of Cu at the potential of 330 mV; the Cu/Co mass ratio in the Cu precipitate was 224. The Co precipitation ratio in the xanthate precipitation of Co, at a potential of 170 mV, was 99.9%, and the Co/Zn mass ratio in the Co precipitate was 28.0. The Zn precipitation ratio reached 99.9% for sulfide precipitation of Zn at the potential of 30 mV, and the Zn/Mn mass ratio in the Zn precipitate was 1.41. The Mn precipitation ratio reached 99.9% after neutralization.

  8. Corrosion Fatigue Behavior of 316LN SS in Acidified Sodium Chloride Solution at Applied Potential

    Science.gov (United States)

    Poonguzhali, A.; Pujar, M. G.; Mallika, C.; Mudali, U. Kamachi

    2015-05-01

    The influence of acidified 1 M NaCl solution by addition of 2 ml/L of HCl on the cyclic plastic deformation of AISI Type 316LN SS containing 0.07 wt.% and 0.22 wt.% N was investigated as a function of the applied potentials. The corrosion fatigue (CF) behavior of stainless steel (SS) was explained vis-a-vis the dislocation behavior, the propensity to form microcracks, and the evolution of the current transients based on the studies carried out at both room-temperature and boiling conditions. CF experiments were conducted using round tensile specimens at a stress ratio of 0.5 and a frequency of 0.1 Hz. Two different kinds of damage mechanisms were observed (I) the damage mechanism in the stable-passive state was correlated with the localization of the anodic dissolution due to a depassivation-repassivation process, whereas (II) the cyclic stress induced pitting corrosion in the metastable pitting state, which resulted in formation of microcracks. The study of the microcracking process and its evolution is a key to the physical mechanism by which the fatigue life of stainless steels would be affected in an aqueous corrosive solution under the applied potential.

  9. Passivation Characteristics of Alloy Corrosion-Resistant Steel Cr10Mo1 in Simulating Concrete Pore Solutions: Combination Effects of pH and Chloride

    Directory of Open Access Journals (Sweden)

    Zhiyong Ai

    2016-09-01

    Full Text Available The electrochemical behaviour for passivation of new alloy corrosion-resistant steel Cr10Mo1 immersed in alkaline solutions with different pH values (13.3, 12.0, 10.5, and 9.0 and chloride contents (0.2 M and 1.0 M, was investigated by various electrochemical techniques: linear polarization resistance, electrochemical impedance spectroscopy and capacitance measurements. The chemical composition and structure of passive films were determined by XPS. The morphological features and surface composition of the immersed steel were evaluated by SEM together with EDS chemical analysis. The results evidence that pH plays an important role in the passivation of the corrosion-resistant steel and the effect is highly dependent upon the chloride contents. In solutions with low chloride (0.2 M, the corrosion-resistant steel has notably enhanced passivity with pH falling from 13.3 to 9.0, but does conversely when in presence of high chloride (1.0 M. The passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer enriched in Fe oxides and hydroxides, and an inner layer, rich in Cr species. The film composition varies with pH values and chloride contents. As the pH drops, more Cr oxides are enriched in the film while Fe oxides gradually decompose. Increasing chloride promotes Cr oxides and Fe oxides to transform into their hydroxides with little protection, and this is more significant at lower pH (10.5 and 9.0. These changes annotate passivation characteristics of the corrosion-resistant steel in the solutions of different electrolyte.

  10. Corrosion Behavior of Stainless Steels in Neutral and Acidified Sodium Chloride Solutions by Electrochemical Impedance Spectroscopy

    Science.gov (United States)

    Calle, L. M.; Kolady, M. R.; Vinje, R. D.

    2004-01-01

    The objective of this work was to evaluate the corrosion performance of three alloys by Electrochemical Impedance Spectroscopy (EIS) and to compare the results with those obtained during a two-year atmospheric exposure study.' Three alloys: AL6XN (UNS N08367), 254SM0 (UNS S32154), and 304L (UNS S30403) were included in the study. 304L was included as a control. The alloys were tested in three electrolyte solutions which consisted of neutral 3.55% NaC1, 3.55% NaC1 in 0.lN HC1, and 3.55% NaC1 in 1.ON HC1. These conditions were expected to be less severe, similar, and more severe respectively than the conditions at NASA's Kennedy Space Center launch pads.

  11. Influence of Heat Treatment on the Corrosion of Microalloyed Steel in Sodium Chloride Solution

    Directory of Open Access Journals (Sweden)

    Asiful Hossain Seikh

    2013-01-01

    Full Text Available Microalloyed Steels find wide application in car bodies and other engineering parts because of its high strength as well as high ductility. Very fine grained microstructure is the reason behind the combination of strength and ductility. It has been reported that repeated quenching leads to further refining of microstructure. In the present investigation, corrosion resistance property of E34 microalloy steel has been studied in 3.5% NaCl solution in different microstructural conditions such as the as rolled one and three repeated quenched conditions. Weight loss, potentiodynamic polarization method, and electrochemical impedance spectroscopy (EIS techniques have been used. To reveal the corrosion resistance of different treated steels, some significant characterization parameters such as Ecorr, Icorr, Rp, and Rct in linear polarization and EIS curves were analyzed and compared. It is found that with repeated recrystallization grains become finer, and corrosion rate increases suggesting that a compromise has to strike between high mechanical property and corrosion rate.

  12. The extraction of zinc and other minor metals from concentrated ammonium chloride solutions with D2EHPA and Cyanex 272

    Directory of Open Access Journals (Sweden)

    Amer, S.

    1995-12-01

    Full Text Available A comparative study is made of the extractants D2EHPA and Cyanex 272 for the zinc and minor metal extraction from aqueous concentrated ammonium chloride solutions, as those of the leaching liquors of the CENIM-LNETI process. Extraction equilibrium data for zinc are presented as extraction isotherms at constant pH and at a temperature of 50 °C. Zinc extraction and coextraction of minor metal ions as Cu, Ca, Pb, Mg, Cd, Co, Ni and Hg are studied. Mercury does not extract from concentrated ammonium chloride solutions. Cyanex 272 shows a better selectivity for zinc with regard to the minor metals than D2EHPA, which is especially remarkable for calcium, the most coextracted element by D2EHPA. Nickel and cadmium coextraction is negligible for both extractants. The possible use of the Cyanex 272 as an alternative to D2EHPA is considered.

    Se realiza un estudio comparativo del comportamiento del D2EHPA y del Cyanex 272 durante la extracción del cinc y otros metales minoritarios de soluciones acuosas concentradas de cloruro amónico, como las de las soluciones de lixiviación del proceso CENIM-LNETI. Se presentan los datos de equilibrio de extracción del cinc en forma de isotermas de extracción a una temperatura de 50 °C y pH constante y se estudia la coextracción de los metales minoritarios Cu, Ca, Pb, Mg, Cd, Co, Ni y Hg. El mercurio no se extrae de las soluciones concentradas de cloruro amónico. La selectividad del Cyanex 272 para el cinc respecto de esos metales minoritarios es mejor que la del D2EHPA, siendo verdaderamente notable para el calcio, que es la impureza que más se coextrae con el D2EHPA. La coextracción de níquel y de cadmio es muy pequeña para ambos extractantes. Se considera la posibilidad del uso alternativo del Cyanex 272 en lugar del D2EHPA.

  13. Selective ion exchange recovery of rare earth elements from uranium mining solutions

    Science.gov (United States)

    Rychkov, Vladimir N.; Kirillov, Evgeny V.; Kirillov, Sergey V.; Bunkov, Grigory M.; Mashkovtsev, Maxim A.; Botalov, Maxim S.; Semenishchev, Vladimir S.; Volkovich, Vladimir A.

    2016-09-01

    A comparative study of rare earth, ferric and aluminum ions ion exchange behavior on gel sulfonated p;olystyrene cation exchange resins depending on the degree of the matrix cross-linking and pH of the solution is presented. Selective ion exchange of REEs is possible at the pH range of 1.5-2.0 using strongly acidic cation exchange resins containing more than 8 % of DVB. The preliminary results of testing the efficiency of REEs recovery from the industrial uranium underground leaching solutions are also presented.

  14. Transurethral enucleation of large benign prostatic hyperplasia in sodium chloride solution

    Directory of Open Access Journals (Sweden)

    I. N. Shvarev

    2016-01-01

    Full Text Available Background. Transurethral resection is a generally recognized treatment for small to medium-sized benign prostatic hyperplasia (BPH. Numerous original tools are proposed for surgery of large BPH. These include laser (holmium laser enucleation of the prostate and transurethral (transurethral enucleation with bipolar (TUEB enucleation in 0.9 % NaCl solution, which are accompanied by removal of the maximum adenoma tissue volume, short-term recovery, and a substantially fewer early and late complications.Objective: to evaluate the safety and efficiency of TUEB in patients with large BPH.Subjects and methods. TUEB was carried out in 58 patients with large BPH. Their mean age was 64 years. The gland size was ≥ 102 сm3. The residual urine volume in all the patients was more than 100 ml. One year later, the results of treatment were analyzed using the International Prostate Symptom Score (IPSS, Quality of Life (QoL Questionnaire, as well as from residual urine volume and remaining prostate tissue.Results. The mean time of surgery and enucleation was 90 and 55 min, respectively. The mean volume of removed adenoma tissue was 99 ml. By the end of month 2 following TUEB, there was a progressive reduction in the total IPSS and QoL scores from 35 to 7 and from 5 to 1, respectively, which preserved this trend by the end of a 1-year follow-up. study. The residual urine amount was less than 30 ml. The mean volume of the prostate tissue left was 8.5 сm3 and less than 11.0 сm3. The ultrasound anatomy of the prostatic urethra (transformation of thin-walled spherical TUR defect that is characteristic slit-like one resembles the inverted letter Y eventually formed by the end of the 1-year follow-up. Stricture of the urethra and contracture of the bladder neck were noted in none of the cases. Conclusion. TUEB is an alternative to open surgery in patients with the enlarged prostate. The use of isotonic NaCl solution as washing fluid allows one to plan

  15. Corrosion Resistance and Pitting Behaviour of Low-Carbon High-Mn Steels in Chloride Solution

    Directory of Open Access Journals (Sweden)

    Grajcar A.

    2016-06-01

    Full Text Available Corrosion resistance of the X4MnSiAlNbTi27-4-2 and X6MnSiAlNbTi26-3-3 type austenitic steels, after hot deformation as well as after cold rolling, were evaluated in 3.5% NaCl solution using potentiodynamic polarization tests. A type of nonmetallic inclusions and their pitting corrosion behaviour were investigated. Additionally, the effect of cold deformation on the corrosion resistance of high-Mn steels was studied. The SEM micrographs revealed that corrosion damage formed in both investigated steels is characterized by various shapes and an irregular distribution at the metallic matrix, independently on the steel state (thermomechanically treated or cold worked. Corrosion pits are generated both in grain interiors, grain boundaries and along the deformation bands. Moreover, corrosion damage is stronger in cold deformed steels in comparison to the thermomechanically treated specimens. EDS analysis revealed that corrosion pits preferentially nucleated on MnS and AlN inclusions or complex oxysulphides. The morphology of corrosion damage in 3.5% NaCl supports the data registered in potentiodynamic tests.

  16. Real surface area of the aluminium electrode in sodium chloride solution

    Directory of Open Access Journals (Sweden)

    Z. RAKOCEVIC

    1999-11-01

    Full Text Available By combining the techniques of electrochemical slow potentiodynamic, AC impedance and atomic force microscopy (AFM, it was shown that the differences in the anodic dissolution rates of Al in 0.5 NaCl solutions as measured experimentally in the potential region between the corrosion and pitting potential, are mainly due to differences in surface roughness of the electrodes used. It was shown that mechanical grinding and polishing of the electrode surface with emery paper (400 grit and alumina polishing powder (f 0.25 mm can produce surfaces differing by a factor of 6 in the roughness factor Ra. By using AFM estimates of the roughness factors a true electrode capacitance of 4.63 µC cm-2 and thickness dox ~ 2.0 nm for the barrier layer of the surface film was estamited. The outer part of the film is porous, partly as amorphous Al(OH3, or crystalline bayerite (Al2O3.3H2O.

  17. Hydrate film growth at the interface between gaseous CO2 and sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    PENG BaoZi; SUN ChangYu; CHEN GuangJin; YANG LanYing; ZHOU Wei; PANG WeiXin

    2009-01-01

    Greenhouse gas CO2 has become a serious problem for human beings. The hydrate technology has been considered as a possible approach to sequester CO2. In this work, the lateral growth rates of a CO2 hydrate film in aqueous NaCl solutions of different concentrations were measured by means of suspending a single gas bubble in liquid. The results show that the film growth rates depended on not only the driving force, but also the NaCl concentration, and the film growth rates decreased with the increasing NaCl concentration. The simple relationship vf∝△T6/2 could be used to correlate the hydrate film growth rate of a CO2 + NaCl + water system by introducing a NaCl concentration-dependent coef-ficient. The film thickness was investigated experimentally and evaluated theoretically; the results show that it became thicker at a higher NaCl concentration when the temperature and pressure were specified. In addition, a series of interesting phenomena, such as the occurrence of double hydrate films, were displayed and discussed.

  18. Hydrate film growth at the interface between gaseous CO2 and sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Greenhouse gas CO2 has become a serious problem for human beings. The hydrate technology has been considered as a possible approach to sequester CO2. In this work, the lateral growth rates of a CO2 hydrate film in aqueous NaCl solutions of different concentrations were measured by means of suspending a single gas bubble in liquid. The results show that the film growth rates depended on not only the driving force, but also the NaCl concentration, and the film growth rates decreased with the increasing NaCl concentration. The simple relationship vf ∝ΔT5/2 could be used to correlate the hydrate film growth rate of a CO2 + NaCl + water system by introducing a NaCl concentration-dependent coefficient. The film thickness was investigated experimentally and evaluated theoretically; the results show that it became thicker at a higher NaCl concentration when the temperature and pressure were specified. In addition, a series of interesting phenomena, such as the occurrence of double hydrate films, were displayed and discussed.

  19. Environmentally Assisted Cracking of Alloy 7050-T7451 Exposed to Aqueous Chloride Solutions

    Science.gov (United States)

    Braun, Reinhold

    2016-03-01

    The stress corrosion cracking (SCC) behavior of 7050-T7451 plate material was investigated in short-transverse direction performing constant load and constant extension rate tests. Smooth and notched tensile specimens were permanently immersed in substitute ocean water and in an aqueous solution of 0.6 M NaCl + 0.06 M (NH4)2SO4. Alloy 7050-T7451 exhibited high SCC resistance in both synthetic environments. However, conducting cyclic loading tests, environment-induced cracking was observed. Applying a sawtooth waveform, notched tensile specimens were strained under constant load amplitude conditions at constant displacement rates ranging from 2 × 10-6 to 2 × 10-4 mms-1. The stress ratio R = σ min/ σ max was 0.1 with maximum stresses of 300 and 400 MPa. When cyclically loaded in substitute ocean water, notched specimens failed predominantly by transgranular environment-induced cracking. Striations were observed on the cleavage-like facets. The number of cycles-to-failure decreased with decreasing displacement rate. A slope of 0.5 was obtained by fitting the logarithmic plot of number of cycles-to-failure vs nominal loading frequency, indicating a hydrogen embrittlement mechanism controlled by diffusion.

  20. Galvanic corrosion behavior of die cast AZ91D magnesium alloy in chloride solution

    Institute of Scientific and Technical Information of China (English)

    Zhensong Tong; Wei Zhang; Jiuqing Li; Jin Gao; Jiquan He; Ji Zhou

    2004-01-01

    The galvanic corrosion behavior of die cast AZ91D magnesium alloy coupled with H62 brass, 316L stainless steel, A3steel and LY12 aluminum alloy of different areas in 3.5% NaC1 solution was studied. The free corrosion potentials, galvanic potentials and currents of these galvanic couples were measured. The galvanic effects were determined by the mass loss and regression method using three points. The results show that: (1) In these four kinds of couples AZ91D acts as the anode, whose galvanic corrosion behavior is mainly controlled by the cathodic polarization; (2) The free corrosion potentials of these four kinds of couples change a liffle with time and cathodic/anodic area ratio (CAAR); (3) The galvanic potential of AZ91D/LY12 moves positively with the increase of time and CAAR; (4) The galvanic currents increase with CAAR, but there is difference in the current change between different couples; (5) The anodic dissolution rate of the magnesium alloy increases by 2-3 orders after being coupled with these four kinds of metals and the galvanic effects of these couples have such a relation as γH62>γ316LS.S>γLY12 >γA3.

  1. Electrochemical behaviour of brass in chloride solution concentrations found in eccrine fingerprint sweat

    Energy Technology Data Exchange (ETDEWEB)

    Bond, John W., E-mail: jwb13@le.ac.uk [Department of Chemistry, George Porter Building, University of Leicester, University Road, Leicester LE1 7RH (United Kingdom); Lieu, Elaine [Department of Physics and Astronomy, University of Leicester, University Road, Leicester LE1 7RH (United Kingdom)

    2014-09-15

    Highlights: • Corrosion of brass in NaCl concentrations found in eccrine sweat was investigated. • Concentrations < 0.2 M produce a layer of mainly zinc oxide after 24 h. • A concentration of 0.2 M enables active corrosion of brass at room temperature. • 0.2 M NaCl gives both zinc and copper dissolution. • 24-h immersion of brass in 0.2 M NaCl gives an oxide film thickness of 1.3 nm. - Abstract: In this work, the corrosion properties of α phase brass immersed in concentrations of aqueous NaCl solutions that are typically found in eccrine fingerprint sweat and range between 0.01 M and 0.2 M have been analysed. Analysis methods employed were electrochemical techniques, X-ray photoelectron spectroscopy and optical profiling. For NaCl concentrations <0.2 M, active corrosion did not occur although, after a period of 24 h, a passivating layer of mainly zinc oxide formed. At a concentration of 0.2 M active corrosion did occur, with measured corrosion potentials consistent with both brass and copper dissolution. A 1 h contact time at this concentration (0.2 M) resulted in the formation of a zinc oxide passivating layer with the surface ratio of zinc oxide to copper oxide increasing with time. Film thickness was calculated to be of the order of 1.3 nm after 24 h contact. Formation of oxide layers on brass by fingerprint sweat as observed here may well have implications for the successful investigation of crime by the visualisation of corrosion fingerprint ridge patterns or the reduction of hospital environmental contamination by hand contact with brass objects such as door handles or taps.

  2. The Synergistic Effect of Iodide and Sodium Nitrite on the Corrosion Inhibition of Mild Steel in Bicarbonate–Chloride Solution

    Directory of Open Access Journals (Sweden)

    Gaius Debi Eyu

    2016-10-01

    Full Text Available The effect of potassium iodide (KI and sodium nitrite (NaNO2 inhibitor on the corrosion inhibition of mild steel in chloride bicarbonate solution has been studied using electrochemical techniques. Potentiodynamic polarisation data suggest that, when used in combination, KI and NaNO2 function together to inhibit reactions at both the anode and the cathode, but predominantly anodic. KI/NO2− concentration ratios varied from 2:1 to 2:5; inhibition efficiency was optimized for a ratio of 1:1. The surface morphology and corrosion products were analysed using scanning electron microscopy (SEM and X-ray diffractometry (XRD. The latter shows that the addition of I− to NO2 facilitates the formation of a passivating oxide (γ-Fe2O3 as compared to NO2− alone, decreasing the rate of metal dissolution observed in electrochemical testing. The synergistic effect of KI/NO2− inhibition was enhanced under the dynamic conditions associated with testing in a rotating disc electrode.

  3. Chloride as tracer of solute transport in the aquifer-aquitard system in the Pearl River Delta, China

    Science.gov (United States)

    Kuang, Xingxing; Jiao, Jiu Jimmy; Wang, Ya

    2016-08-01

    A 1D numerical model is constructed to investigate the impact of sedimentation and sea level changes on transport of Cl- in the aquifer-aquitard system in the Pearl River Delta (PRD), China. The model simulates the evolution of the vertical Cl- concentration profiles during the Holocene. Sedimentation is modeled as a moving boundary problem. Chloride concentration profiles are reconstructed for nine boreholes, covering a wide area of the PRD, from northwest to southeast. Satisfactory agreement is obtained between simulated and measured Cl- concentration profiles. Diffusion solely is adequate to reproduce the vertical Cl- concentration profiles, which indicates that diffusion is the regionally dominant vertical transport mechanism across the aquitards in the PRD. The estimated effective diffusion coefficients of the aquitards range from 2.0 × 10-11 to 2.0 × 10-10 m2/s. The effective diffusion coefficients of the aquifers range from 3.0 × 10-11 to 4.0 × 10-10 m2/s. Advective transport tends to underestimate Cl- concentrations in the aquitard and overestimate Cl- concentrations in the basal aquifer. The results of this study will help understand the mechanisms of solute transport in the PRD and other deltas with similar geological and hydrogeological characteristics.

  4. Removal of malachite green dye from aqueous solution using mesoporous silica synthesized from 1-octyl-3-methylimidazolium chloride ionic liquid

    Science.gov (United States)

    Ekka, Basanti; Nayak, Soumitra Ranjan; Dash, Priyabrat; Patel, Raj Kishore

    2016-04-01

    In this research, mesoporous silica was synthesized via a modified sol-gel route using 1-octyl-3-methylimidazolium chloride and was employed to remove malachite green (MG) dye from aqueous solution. Subsequently, this material was characterized and identified by different techniques such as Fourier transform infrared spectroscopy (FT-IR), N2 adsorption-desorption method, scanning electron microscopy (SEM), and thermosgravimetric analysis (TGA). Unique properties such as high surface area and pore diameter, in addition to highly reactive atoms and presence of various functional groups make the mesoporous silica possible for efficient removal of malachite green (MG). In batch experimental set-up, optimum conditions for quantitative removal of MG by mesoporous silica was attained by varying different variables such as adsorbent dosage, initial dye concentration, contact time, and pH. Optimum values were set as pH of 8.0, 0.5 g of adsorbent at contact time of 120 min. The adsorption of MG follows the pseudo-second-order rate equation. Equilibrium data fitted well with the Freundlich model at all amount of adsorbent, while maximum adsorption capacity was 5.981 mg g-1 for 0.5 g mesoporous silica synthesized in IL.

  5. EFFECT OF RADIATION ON HIGH-CHARGE-DENSITY POLYDIALLY-DIMETHYL AMMONIUM CHLORIDE IN DILUTE AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Ya-long Zhang; Min Yi; Jing Ren; Hong-fei Ha

    2003-01-01

    The effect of radiation on high-charge-density cationic polymer, polydiallyl-dimethyl ammonium chloride (polyDADMAC), in dilute aqueous solution was investigated. The irradiated samples were characterized in terms of reduced viscosity and electric conductivity. The crosslinking reaction of polyDADMAC chains occurs preferentially in the irradiated samples at a concentration of polyDADMAC higher than 1.3 g/100 mL that was induced indirectly by the OH radicals, one of the radiolysis products of water. In more dilute samples (less than 0.8 g/100 mL) the chain scission of macro radicals appears to be the main reaction. N2O atmosphere enhances the erosslinking due to the extra OH radicals produced by reaction between N2O and eaq, another radiolysis products of water. Methanol and some mineral salts such as KC1, KBr inhibit the crosslinking to a certain extent. The mechanism of sensitization and inhibition is discussed in detail.

  6. Evidence of mass exchange between inside and outside of sonoluminescing bubble in aqueous solution of terbium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Jinfu, E-mail: liang.shi2007@163.com [School of Physics and Electronic Science, Guizhou Normal University, Guiyang 550001 (China); Chen, Weizhong, E-mail: wzchen@nju.edu.cn [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); Wang, Xun; Yang, Jing; Chen, Zhan [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China)

    2016-12-16

    Highlights: • Time-resolved spectra of SBSL were obtained for Tb{sup 3+} ions emission lines. • Mass exchange between inside and outside of SL bubble was probed via Tb{sup 3+} ions lines. • The argon rectification hypothesis was tested by time-resolved spectra of SBSL. • The rate of mass exchange inside an SBSL bubble increases with increasing sound pressure. - Abstract: Spectra of single-bubble sonoluminescence (SBSL) were obtained for Tb{sup 3+} ions emission lines from bubbles in an aqueous solution of terbium chloride (TbCl{sub 3}). The spectra provide experimental evidence to prove that an air bubble driven by strong ultrasound will not eventually become a rectified pure argon bubble, which is not as predicted by the argon rectification hypothesis. The time-resolved spectra of SBSL show a mass exchange of material such as Tb{sup 3+} ions between the inside and outside of the bubble. With increasing sound pressure, the rate of mass exchange and the SBSL intensity increases.

  7. [Studies on local anesthetics. Part 183: micellization and thermodynamic parameters of heptacainium chloride in the solution of potassium bromide].

    Science.gov (United States)

    Andriamainty, F; Cizmárik, J; Malík, I; Horvat, S

    2008-06-01

    The critical micellar concentration (CMC) of the local anaesthetic agent heptacainium chloride in the solution of KBr was determined by the spectrophotometric method in the UV region of the spectrum at the temperature range of t = 20-40 degrees C and pH = 4.5-5.0. The dependence of CMC on the temperature T turned out forming the U-shape with the minimum at the temperature of t = 25 degrees C. The parabolic dependence of CMC on the temperature T was drawn by the fitting of the values using the polynomial function and the so-called power law equation. The CMC dependence on the temperature T was fitted by the second degree polynomial function. The obtained parabolic equations were applied to the "phase separation model", so the following thermodynamic parameters could be calculated: standard Gibbs free energy (deltaG), enthalpy (deltaH degrees), and entropy (deltaS degrees). The thermodynamic parameters were further used to determine the so-called entropy-enthalpy compensation of the systems under study. The compensation temperature was in the following range: (301 +/- 1-303 +/- 3)K. Then the temperature dependence of the enthalpy (deltaH degrees) and entropy (-TdeltaS degrees) contributions to the standard Gibbs free energy (deltaG degrees) for all prepared concentrations of the compound were calculated.

  8. Kinetic and equilibrium studies of the removal of cadmium ions from acidic chloride solutions by hydrophobic pyridinecarboxamide extractants

    Energy Technology Data Exchange (ETDEWEB)

    Borowiak-Resterna, Aleksandra [Institute of Chemical Technology and Engineering, Poznan University of Technology, Pl. Marii Sklodowskiej-Curie 2, 60-965 Poznan (Poland); Cierpiszewski, Ryszard [Poznan University of Economics, Faculty of Commodity Science, al. Niepodleglosci 10, 61-875 Poznan (Poland); Prochaska, Krystyna, E-mail: Krystyna.Prochaska@put.poznan.pl [Institute of Chemical Technology and Engineering, Poznan University of Technology, Pl. Marii Sklodowskiej-Curie 2, 60-965 Poznan (Poland)

    2010-07-15

    Liquid-liquid extraction of cadmium(II) from acidic chloride solutions was carried out with alkyl derivatives of pyridinecarboxamide in toluene with addition of 2-ethylhexan-1-ol as modifier. Equilibrium as well as kinetic studies was performed. The kinetic studies of a Cd(II) extraction process were carried out with a Lewis cell having a constant interfacial area. Cadmium(II) concentration in the aqueous phases was determined by atomic absorption spectroscopy (Varian SPECTR AA800). The results of equilibrium experiments showed that cadmium(II) was quantitatively extracted with N,N-dihexylpyridine-3-carboxamide whereas the derivative N,N-dihexylpyridine-2-carboxamide was not able to transfer Cd(II) ions from the aqueous phase to the organic one. Thus, the kinetics of extraction and the initial extraction rate were examined only in the systems with N,N-dihexylpyridine-3-carboxamide. The obtained experimental data as well as the calculated values of mass transfer coefficients suggest that the investigated process of extraction of Cd(II) by means of pyridinecarboxamide as extractant occurs in the mixed diffusion-kinetic region. Moreover, the results of adsorption studies indicated that the extraction of Cd(II) with a hydrophobic extractant should be considered as an interfacial process.

  9. A new dioxime corrosion inhibitor for the protection and conservation of copper: synthesis, characterization and evaluation in acidic chloride solution

    Science.gov (United States)

    Abu-Baker, Ahmad N.; Al-Qudah, Mahmoud A.

    2016-08-01

    This study aimed to investigate a new dioxime compound as a corrosion inhibitor for copper. The compound (4,6-dihydroxy benzene-1,3-dicarbaldehyde dioxime) was synthesized and characterized by nuclear magnetic resonance spectroscopy. Electrochemical impedance spectroscopy and potentiodynamic polarization measurements were used to compare the dioxime compound with benzotriazole for their effectiveness as corrosion inhibitors for copper in 0.1 M HCl solution. Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) were used to investigate the bonding mechanisms and morphological changes of the two inhibitors on the copper surface. The electrochemical techniques showed that the new dioxime compound was more effective than benzotriazole in inhibiting copper corrosion in the acidic chloride medium. The FTIR and SEM results indicated that the dioxime compound was able to coordinate with copper ions and formed a protective film on the copper surface. It was concluded that the new dioxime compound proved effectiveness to be used as a corrosion inhibitor for the protection and conservation of copper.

  10. Studies of removal of palladium(II) ions from chloride solutions on weakly and strongly basic anion exchangers.

    Science.gov (United States)

    Hubicki, Z; Wołowicz, A; Leszczyńska, M

    2008-11-30

    Palladium and its compounds find wide application in industry as a catalytic agent in different manufacture processes. Recovery of precious metals from industrial wastes is difficult and time consuming but in spite of these disadvantages it becomes profitable. Palladium(II) ions sorption from various chloride solutions of the composition: 0.1-6.0M HCl-0.00056 M Pd(II), 1.0M ZnCl(2)-0.1M HCl-0.00056 M Pd(II), 1.0M AlCl(3)-0.1M HCl-0.00056 M Pd(II) on the weakly and strongly basic anion exchangers (Varion ATM, Varion ADM and Varion ADAM) was discussed. The sorption research of Pd(II) ions on these resins was carried out by means of static and dynamic methods. The dynamic processes were applied in order to determine the breakthrough curves of Pd(II) ions. Moreover, the working ion-exchange capacities as well as the weight and bed distribution coefficients were determined from the Pd(II) breakthrough curves. The recovery factors of Pd(II) ions (% R) depending on the phase contact time were obtained by means of static methods. The highest ion-exchange capacities for the 0.1-6.0M HCl-0.00056 M Pd(II) systems were obtained for the weakly basic ion-exchange resin Varion ADAM.

  11. Pitting Corrosion Behaviour of New Corrosion-Resistant Reinforcement Bars in Chloride-Containing Concrete Pore Solution

    Science.gov (United States)

    Liu, Yao; Chu, Hong-yan; Wang, Danqian; Ma, Han; Sun, Wei

    2017-01-01

    In this study, the pitting behaviour of a new corrosion-resistant alloy steel (CR) is compared to that of low-carbon steel (LC) in a simulated concrete pore solution with a chloride concentration of 5 mol/L. The electrochemical behaviour of the bars was characterised using linear polarisation resistance (LPR) and electrochemical impedance spectroscopy (EIS). The pitting profiles were detected by reflective digital holographic microscopy (DHM), scanning electron microscopy (SEM), and the chemical components produced in the pitting process were analysed by X-ray energy dispersive spectroscopy (EDS). The results show that the CR bars have a higher resistance to pitting corrosion than the LC bars. This is primarily because of the periodic occurrence of metastable pitting during pitting development. Compared to the pitting process in the LC bars, the pitting depth grows slowly in the CR bars, which greatly reduces the risk of pitting. The possible reason for this result is that the capability of the CR bars to heal the passivation film helps to restore the metastable pits to the passivation state. PMID:28777327

  12. Acid-activated spent bleaching earth as a sorbent for chromium (VI) in aqueous solution.

    Science.gov (United States)

    Low, K S; Lee, C K; Lee, T S

    2003-02-01

    Spent bleaching earth, an industrial waste produced after the bleaching of crude palm oil, was investigated for its potential in removing Cr(VI) from aqueous solution. The earth was treated with different amounts of sulfuric acid and under different activation temperatures. Results show that the optimum treatment process involved 10% sulfuric acid at 350 degrees C. The effects of contact time, pH, initial concentration, sorbent dosage, temperature, sorption isotherms and the presence of other anions on its sorption capacity were studied. Isotherm data could be fitted into a modified Langmuir isotherm model implying monolayer coverage of Cr(VI) on acid activated spent bleaching earth. The maximum sorption capacity derived from the Langmuir isotherm was 21.2 mg g(-1). This value was compared with those of some other low cost sorbents. Studies of anion effect on the uptake of Cr(VI) on acid activated spent bleaching earth provided the following order of suppression: EDTA >PO4(3-)>SO4(2-)>NO3(-)>Cl(-).

  13. OnEarth: An Open Source Solution for Efficiently Serving High-Resolution Mapped Image Products

    Science.gov (United States)

    Thompson, C. K.; Plesea, L.; Hall, J. R.; Roberts, J. T.; Cechini, M. F.; Schmaltz, J. E.; Alarcon, C.; Huang, T.; McGann, J. M.; Chang, G.; Boller, R. A.; Ilavajhala, S.; Murphy, K. J.; Bingham, A. W.

    2013-12-01

    This presentation introduces OnEarth, a server side software package originally developed at the Jet Propulsion Laboratory (JPL), that facilitates network-based, minimum-latency geolocated image access independent of image size or spatial resolution. The key component in this package is the Meta Raster Format (MRF), a specialized raster file extension to the Geospatial Data Abstraction Library (GDAL) consisting of an internal indexed pyramid of image tiles. Imagery to be served is converted to the MRF format and made accessible online via an expandable set of server modules handling requests in several common protocols, including the Open Geospatial Consortium (OGC) compliant Web Map Tile Service (WMTS) as well as Tiled WMS and Keyhole Markup Language (KML). OnEarth has recently transitioned to open source status and is maintained and actively developed as part of GIBS (Global Imagery Browse Services), a collaborative project between JPL and Goddard Space Flight Center (GSFC). The primary function of GIBS is to enhance and streamline the data discovery process and to support near real-time (NRT) applications via the expeditious ingestion and serving of full-resolution imagery representing science products from across the NASA Earth Science spectrum. Open source software solutions are leveraged where possible in order to utilize existing available technologies, reduce development time, and enlist wider community participation. We will discuss some of the factors and decision points in transitioning OnEarth to a suitable open source paradigm, including repository and licensing agreement decision points, institutional hurdles, and perceived benefits. We will also provide examples illustrating how OnEarth is integrated within GIBS and other applications.

  14. Ion-pair formation in aqueous strontium chloride and strontium hydroxide solutions under hydrothermal conditions by AC conductivity measurements.

    Science.gov (United States)

    Arcis, H; Zimmerman, G H; Tremaine, P R

    2014-09-01

    Frequency-dependent electrical conductivities of solutions of aqueous strontium hydroxide and strontium chloride have been measured from T = 295 K to T = 625 K at p = 20 MPa, over a very wide range of ionic strength (3 × 10(-5) to 0.2 mol kg(-1)), using a high-precision flow AC conductivity instrument. Experimental values for the concentration-dependent equivalent conductivity, Λ, of the two electrolytes were fitted with the Turq-Blum-Bernard-Kunz ("TBBK") ionic conductivity model, to determine ionic association constants, K(A,m). The TBBK fits yielded statistically significant formation constants for the species SrOH(+) and SrCl(+) at all temperatures, and for Sr(OH)2(0) and SrCl2(0) at temperatures above 446 K. The first and second stepwise association constants for the ion pairs followed the order K(A1)(SrOH(+)) > K(A1)(SrCl(+)) > K(A2)[Sr(OH)2(0)] > K(A2)[SrCl2(0)], consistent with long-range solvent polarization effects associated with the lower static dielectric constant and high compressibility of water at elevated temperatures. The stepwise association constants to form SrCl(+) agree with previously reported values for CaCl(+) to within the combined experimental error at high temperatures and, at temperatures below ∼375 K, the values of log10 KA1 for strontium are lower than those for calcium by up to ∼0.3-0.4 units. The association constants for the species SrOH(+) and Sr(OH)2(0) are the first accurate values to be reported for hydroxide ion pairs with any divalent cation under these conditions.

  15. Multistate outbreak of Serratia marcescens bloodstream infections caused by contamination of prefilled heparin and isotonic sodium chloride solution syringes.

    Science.gov (United States)

    Blossom, David; Noble-Wang, Judith; Su, John; Pur, Stacy; Chemaly, Roy; Shams, Alicia; Jensen, Bette; Pascoe, Neil; Gullion, Jessica; Casey, Eric; Hayden, Mary; Arduino, Matthew; Budnitz, Daniel S; Raad, Isaam; Trenholme, Gordon; Srinivasan, Arjun

    2009-10-12

    To investigate clusters of Serratia marcescens (SM) bloodstream infections (BSIs) at health care facilities in several states and determine whether contaminated prefilled heparin and isotonic sodium chloride solution (hereinafter, saline) syringes from a single manufacturer (company X) were the likely cause, we performed an outbreak investigation of inpatient and outpatient health care facilities from October 2007 through February 2008. Active case finding for clusters of SM BSIs. Information on SM BSIs was obtained, and SM blood isolates were sent to the Centers for Disease Control and Prevention (CDC). Culture specimens were taken from various lots of prefilled heparin and saline syringes by health care facilities and the CDC to test for the presence of SM. The SM isolates from syringes and blood were compared by pulsed-field gel electrophoresis. A total of 162 SM BSIs in 9 states were reported among patients at facilities using prefilled heparin and/or saline syringes made by company X. Cultures of unopened prefilled heparin and saline syringes manufactured by company X grew SM. Of 83 SM blood isolates submitted to the CDC from 7 states, 70 (84%) were genetically related to the SM strain isolated from prefilled syringes. A US Food and Drug Administration inspection revealed that company X was not in compliance with quality system regulations. A multistate outbreak of SM BSIs was associated with intrinsic contamination of prefilled syringes. Our investigation highlights important issues in medication safety, including (1) the importance of pursuing possible product-associated outbreaks suggested by strong epidemiologic data even when initial cultures of the suspected product show no contamination and (2) the challenges of medical product recalls when production has been outsourced from one company to another.

  16. Stability, compatibility and plasticizer extraction of quinine injection added to infusion solutions and stored in polyvinyl chloride (PVC) containers.

    Science.gov (United States)

    Faouzi, M A; Khalfi, F; Dine, T; Luyckx, M; Brunet, C; Gressier, B; Goudaliez, F; Cazin, M; Kablan, J; Belabed, A; Cazin, J C

    1999-12-01

    The stability of quinine was determined in various diluents and in polyvinyl chloride (PVC) containers. The release of diethyhexyl phthalate (DEHP) from PVC bags into intravenous infusions of quinine was also measured. We used an injection of two doses of quinine; quiniforme at 500 mg and quinimax at 400 mg in either 250- or 500-ml PVC infusion bags containing 5% dextrose, to give initial nominal concentrations of 2 or 1 mg ml(-1) quiniforme and 1.6 or 0.8 mg ml(-1) quinimax, the mean concentrations commonly used in clinical practice. Samples were assayed by stability-indicating high-performance liquid chromatography (HPLC) and the clarity was determined visually. Experiments were conducted to determine whether the stability and compatibility of quinine would be compromised, and whether DEHP would be leached from PVC bags and PVC administration sets during storage and simulated infusion. There was no substantial loss of quiniforme and quinimax over 1- or 2-h simulated infusion irrespective of the diluent, and storage during 8 h at 22 degrees C, 48 or 72 h at 4 degrees C and 96 h at 45 degrees C. Leaching of DEHP was also detected during simulated infusion delivery using PVC bags and PVC administration sets. The quantity was less than 2 microg ml(-1). During storage at 4 degrees C and room temperature the leaching of DEHP was low, but when the temperature was 45 degrees C the quantity was high, 21 microg ml(-1). To minimise patient exposure to DEHP, quinine solutions with all drugs should be infused immediately or stored for a maximum of 48 h at 4 degrees C.

  17. Environmentally safe corrosion inhibition of Mg-Al-Zn alloy in chloride free neutral solutions by amino acids

    Energy Technology Data Exchange (ETDEWEB)

    Helal, N.H. [Chemistry Department, Faculty of Science, Fayoum University, Fayoum (Egypt); Badawy, W.A., E-mail: wbadawy@cu.edu.eg [Chemistry Department, Faculty of Science, Cairo University, 12 613 Giza (Egypt)

    2011-07-30

    Highlights: > Phenyl alanine at a concentration of 2 x 10{sup -3} mol dm{sup -3} gives 93% corrosion inhibition efficiency for the corrosion of the Mg-Al-Zn alloy. > The corrosion inhibition process is based on the adsorption of the amino acid molecules on the active sites of the alloy surface by physical adsorption mechanism. > The adsorption free energy was 15.72 kJ mol{sup -1}. - Abstract: The corrosion inhibition of Mg-Al-Zn alloy was investigated in stagnant naturally aerated chloride free neutral solutions using amino acids as environmentally safe corrosion inhibitors. The corrosion rate was calculated in the absence and presence of the corrosion inhibitor using the polarization technique and electrochemical impedance spectroscopy. The experimental impedance data were fitted to theoretical data according to a proposed electronic circuit model to explain the behavior of the alloy/electrolyte interface under different conditions. The corrosion inhibition process was found to depend on the adsorption of the amino acid molecules on the metal surface. Phenyl alanine has shown remarkably high corrosion inhibition efficiency up to 93% at a concentration of 2 x 10{sup -3} mol dm{sup -3}. The corrosion inhibition efficiency was found to depend on the concentration of the amino acid and its structure. The mechanism of the corrosion inhibition process was discussed and different adsorption isotherms were investigated. The free energy of the adsorption process was calculated for the adsorption of different amino acids on the Mg-Al-Zn alloy and the obtained values reveal a physical adsorption of the inhibitor molecules on the alloy surface.

  18. Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

    Directory of Open Access Journals (Sweden)

    Beixiao Zhang

    2010-08-01

    Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

  19. Removal of MCPA from aqueous solutions by acid-activated spent bleaching earth.

    Science.gov (United States)

    Mahramanlioglu, Mehmet; Kizilcikli, Irfan; Biçer, I Ozlem; Tuncay, Melda

    2003-11-01

    The removal of MCPA (4-chloro-2-methyl phenoxyacetic acid) from aqueous solutions by activated spent bleaching earth (SBE) was studied as a function of time, initial concentration, adsorbent concentration, and temperature. The Langmuir and Freundlich isotherms were fitted by the adsorption data obtained. The values of Langmuir and Freundlich constants were determined. The adsorption kinetics was described by the Lagergren equation. Mass transfer coefficient and thermodynamic parameters were also calculated. Column experiments were conducted and brekthrough capacities were found for different concentrations and different flow rates. The study demonstrates that acid-treated SBE could be used as an efficient adsorbent for the removal of MCPA-bearing wastewater effluents.

  20. Removal of 2,4-D from aqueous solution by the adsorbents from spent bleaching earth.

    Science.gov (United States)

    Mahramanlioğlu, M; Kizilcikli, I; Biçer, I O; Tunçay, M

    2000-03-01

    The removal of 2,4-D (2,4-dichlorophenoxyacetic acid) from aqueous solutions by activated spent bleaching earths (SBE) was studied at 20 degrees C. Experiments were performed as a function of time, initial concentration, dose and particle size of the adsorbent. The Langmuir and Freundlich adsorption equations were fitted by the adsorption data obtained. The values of Langmuir and Freundlich constants were determined. The adsorption kinetic was found to follow Lagergren equation. Both the boundary layer and intraparticle diffusion played important roles in the adsorption rate of 2,4-D. As the size of the adsorbent increased, the time to reach equilibrium increased but adsorption capacity decreased.

  1. Adsorption of Rh(III) complexes from chloride solutions obtained by leaching chlorinated spent automotive catalysts on ion-exchange resin Diaion WA21J

    Energy Technology Data Exchange (ETDEWEB)

    Shen Shaobo, E-mail: shaoboshen@metall.ustb.edu.cn [Key Laboratory of Ecological and Recycling Metallurgy, Ministry of Education of China, Beijing 100083 (China); Department of Physical Chemistry, School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Pan Tonglin; Liu Xinqiang; Yuan Lei [Key Laboratory of Ecological and Recycling Metallurgy, Ministry of Education of China, Beijing 100083 (China); Wang Jinchao [Key Laboratory of Ecological and Recycling Metallurgy, Ministry of Education of China, Beijing 100083 (China); Department of Physical Chemistry, School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhang Yongjian; Guo Zhanchen [Key Laboratory of Ecological and Recycling Metallurgy, Ministry of Education of China, Beijing 100083 (China)

    2010-07-15

    It was found that Rh, Pd and Pt contained in the spent ceramic automotive catalysts could be effectively extracted by dry chlorination with chlorine. In order to concentrate Rh(III) ions contained in the chloride solutions obtained, thermodynamic and kinetics studies for adsorption of Rh(III) complexes from the chloride solutions on an anionic exchange resin Diaion WA21J were carried out. Rh, Pd, Pt, Al, Fe, Si, Zn and Pb from the chloride solution could be adsorbed on the resin. The distribution coefficients (K{sub d}) of Rh(III) decreased with the increase in initial Rh(III) concentration or in adsorption temperature. The isothermal adsorption of Rh(III) was found to fit Langmuir, Freundlich and Dubinin-Kaganer-Radushkevich models under the adsorption conditions. The maximum monolayer adsorption capacities Q{sub max} based on Langmuir adsorption isotherms were 6.39, 6.61 and 5.81 mg/g for temperatures 18, 28 and 40 deg. C, respectively. The apparent adsorption energy of Rh was about -7.6 kJ/mol and thus Rh(III) adsorption was a physical type. The experimental data obtained could be better simulated by pseudo-first-order kinetic model and the activation energy obtained was 6.54 J/mol. The adsorption rate of Rh(III) was controlled by intraparticle diffusion in most of time of adsorption process.

  2. Universal charge quenching and stability of proteins in 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride ionic liquid solutions.

    Science.gov (United States)

    Rawat, Kamla; Bohidar, H B

    2012-09-13

    This study reports pH dependent stability of protein dispersions of five common proteins, bovine serum albumin (BSA), human serum albumin (HSA), immunoglobulin (IgG), β-lactoglobulin (β-Lg), and gelatin-B (Gel-B), all having isoelectric pH, pI ≈ 5, in room temperature ionic liquid solutions of 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride (concentration 0-0.2% w/v). Molecular hydrophobicity index, (H-index = hydrophobicity/hydrophilicity) of these molecules spanned the range 0.43-0.87. Electrophoretic characteristics, surface tension data and hydrodynamic size information revealed that IL solutions provide dispersion stability owing to specific protein-IL binding which did not alter their pI values though their surface charge was considerably screened. Change in maximum (ζ(max)) and minimum (ζ(min)) zeta potential values observed at pH ~3 (maximum protonated state) and pH ~8 (maximum deprotonated state) could be described universally as function of IL concentration, c as Δζ(x) = [1 - exp(-ac)] where Δζ(x) is either |(ζ(max) - ζ(w))|/ζ(w) or |(ζ(min) - ζ(w))|/ζ(w), and ζ(w) is the corresponding value in water. Tensiometry data showed two major stages of protein-IL interactions: (i) for c cmc free IL-aggregates begin to form. Similarly, we can define Δγ(x) as either |(γ(max) - γ(w))|/γ(w) at pH 3 or |(γ(min) - γ(w))|/γ(w) at pH 8. Both Δζ(x) and Δγ(x) showed linear dependence with c, Δγ(min, max) (or Δζ(min, max)) = (1 - K(γ) (or K(ζ)) H-index), where the slopes K(ζ) and K(γ) defined intermolecular interactions. Hydrodynamic radii data revealed protein stabilization, circular dichroism spectra implied retention of secondary structures, and Raman spectra confirmed a marginal increase in water structure. Results concluded that selective binding of IL molecules to protein surface in the form of bilayer screen protein surface charge, thereby, contributing to its dispersion stability.

  3. Characterization of liquid-core/liquid-cladding optical waveguides of a sodium chloride solution/water system by computational fluid dynamics.

    Science.gov (United States)

    Kamiyama, Junya; Asanuma, Soto; Murata, Hiroyasu; Sugii, Yasuhiko; Hotta, Hiroki; Sato, Kiichi; Tsunoda, Kin-ichi

    2013-12-01

    A stable liquid/liquid optical waveguide (LLW) was formed using a sheath flow, where a 15% sodium chloride (NaCl) solution functioned as the core solution and water functioned as the cladding solution (15% NaCl/water LLW). The LLW was at least 200 mm in length. The concentration distributions of the liquid core and liquid cladding solutions in the LLW system were predicted by computational fluid dynamics (CFD) to validate the characteristics of the waveguide. The broadening of the region of the fluorescence of Rhodamine B excited by the guided light and the increase in the critical angle of the guided light with the increase in the contact time of the core and the cladding solutions were well explained by CFD calculations. However, no substantial leakage of the guided light was observed despite the considerably large change in the refractive index profile of the LLW; thus, a narrower and longer waveguide was realized.

  4. Earth

    CERN Document Server

    Carter, Jason

    2017-01-01

    This curriculum-based, easy-to-follow book teaches young readers about Earth as one of the eight planets in our solar system in astronomical terms. With accessible text, it provides the fundamental information any student needs to begin their studies in astronomy, such as how Earth spins and revolves around the Sun, why it's uniquely suitable for life, its physical features, atmosphere, biosphere, moon, its past, future, and more. To enhance the learning experience, many of the images come directly from NASA. This straightforward title offers the fundamental information any student needs to sp

  5. Recovery of rare earths from acid leach solutions of spent nickel-metal hydride batteries using solvent extraction

    Institute of Scientific and Technical Information of China (English)

    夏允; 肖连生; 田吉英; 李兆洋; 曾理

    2015-01-01

    The extraction of rare earths from acid leach solutions of spent nickel-metal hydride batteries using a primary amine ex-tractant of N1923 was studied. The effects of feed pH, temperature, agitation rate and time on the extraction of rare earths, as well as stripping agent composition and concentration, phase ratio on the stripping were investigated. In addition, the extraction isotherm was determined. The pilot plant test results showed that the extraction of rare earths reached 99.98% after a five-stage counter current ex-traction. The mixed rare earths oxalates with the 99.77% purity of rare earth elements and impurity content less than 0.05% were ob-tained by the addition of oxalic acids in loaded strip liquors. The extractant exhibited good selectivity of rare earths over base metals of iron, nickel, copper and manganese.

  6. Role of Chloride Ion and Dissolved Oxygen in Electrochemical Corrosion of AA5083-H321 Aluminum-Magnesium Alloy in NaCl Solutions under Flow Conditions

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Flow-induced corrosion consists electrochemical and mechanical components. The present paper has to assessed the role of chloride ion and dissolved oxygen in the electrochemical component of flow induced corrosion for AA5083-H321 aluminum-magnesium alloy which is extensively used in the construction of high-speed boats, submarines, hovercrafts, and desalination systems, in NaCl solutions. Electrochemical tests were carried out at flow velocities of 0, 2, 5, 7 and 10 m/s, in aerated and deaerated NaCl solutions with different sodium chloride concentrations. The results showed that the high rate of oxygen reduction under hydrodynamic conditions causes an increase in the density of pits on the surface. The increase of chloride ions concentration under flow conditions accelerates the rate of anodic reactions, but have no influence on the cathodic reactions. Thus, in the current work, it was found that under flow conditions, due to the elimination of corrosion products inside the pits, corrosion resistance of the alloy is increased.

  7. Volume regulation in mammalian skeletal muscle: the role of sodium-potassium-chloride cotransporters during exposure to hypertonic solutions.

    Science.gov (United States)

    Lindinger, Michael I; Leung, Matthew; Trajcevski, Karin E; Hawke, Thomas J

    2011-06-01

    Controversy exists as to whether mammalian skeletal muscle is capable of volume regulation in response to changes in extracellular osmolarity despite evidence that muscle fibres have the required ion transport mechanisms to transport solute and water in situ. We addressed this issue by studying the ability of skeletal muscle to regulate volume during periods of induced hyperosmotic stress using single, mouse extensor digitorum longus (EDL) muscle fibres and intact muscle (soleus and EDL). Fibres and intact muscles were loaded with the fluorophore, calcein, and the change in muscle fluorescence and width (single fibres only) used as a metric of volume change. We hypothesized that skeletal muscle exposed to increased extracellular osmolarity would elicit initial cellular shrinkage followed by a regulatory volume increase (RVI) with the RVI dependent on the sodium–potassium–chloride cotransporter (NKCC). We found that single fibres exposed to a 35% increase in extracellular osmolarity demonstrated a rapid, initial 27–32% decrease in cell volume followed by a RVI which took 10-20 min and returned cell volume to 90–110% of pre-stimulus values. Within intact muscle, exposure to increased extracellular osmolarity of varying degrees also induced a rapid, initial shrinkage followed by a gradual RVI, with a greater rate of initial cell shrinkage and a longer time for RVI to occur with increasing extracellular tonicities. Furthermore, RVI was significantly faster in slow-twitch soleus than fast-twitch EDL. Pre-treatment of muscle with bumetanide (NKCC inhibitor) or ouabain (Na+,K+-ATPase inhibitor), increased the initial volume loss and impaired the RVI response to increased extracellular osmolarity indicating that the NKCC is a primary contributor to volume regulation in skeletal muscle. It is concluded that mouse skeletal muscle initially loses volume then exhibits a RVI when exposed to increases in extracellular osmolarity. The rate of RVI is dependent on the

  8. Extraction of uranyl nitrate, sulphate and chloride with tri-n-octyl amine (TOA from aqueous solutions

    Directory of Open Access Journals (Sweden)

    DJORDJE M. PETKOVIC

    2001-07-01

    Full Text Available Extraction of uranyl nitrate, chloride and sulphate with tri-n-octyl amine (TOA in benzene as a function of the TOA concentration has been studied. The concentration based extraction equilibrium constants were calculated from the distribution data of the uranyl salts, fitting the parameters of a chemical model to the experimentally obtained extraction isotherms. The calculated equilibrium constants are 46.5, 89.4 and 4.2·104 for uranyl nitrate, chloride and sulphate, respectively. These values are in good agreement with the previously reported extraction equilibrium constants calculated by the inflection point method.

  9. Lithium Sulfuryl Chloride Battery.

    Science.gov (United States)

    Primary batteries , Electrochemistry, Ionic current, Electrolytes, Cathodes(Electrolytic cell), Anodes(Electrolytic cell), Thionyl chloride ...Phosphorus compounds, Electrical conductivity, Calibration, Solutions(Mixtures), Electrical resistance, Performance tests, Solvents, Lithium compounds

  10. Information Technology Infrastructure for the NASA Earth Science Enterprise Solutions Network

    Science.gov (United States)

    Aanstoos, J. V.; Shaw, D. R.; O'Hara, C. G.; Frisbie, T. E.

    2006-12-01

    The NASA Applied Sciences Program uses the term Solutions Network in the context of its Enterprise Architecture to describe the ability of different components of the enterprise to generate ideas for new ways to use NASA missions, research, and/or models in conjunction with operational decision-making processes (or decision support systems) to achieve a particular benefit to society. In this paper, we describe the development of an information technology infrastructure that will facilitate that ability. The two main components of this infrastructure are: the Research Projects Knowledge Base (RPKB); and the Partner Network Knowledge Base (PNKB). The RPKB aims to index all relevant NASA research result publications in a database that will be interoperable with the evolving NASA enterprise architecture system and will share relevant table space with it. In particular, fields from this system identifying relevant NASA missions, models, and data products will be used to cross-index the data collected on published results of research projects. Fields characterizing the research results based on the seven Earth-Sun system science focus areas and the twelve applications of national priority are included. In the course of developing the RPKB, novel uses of existing online databases and search tools have been developed. In addition, data mining tools are being developed for facilitating the location of candidate results and the indexing of relevant matches. The PNKB database will characterize the current network of NASA Earth-Sun system partners. This includes information on organizations and agencies funded by or partnered with NASA to conduct Earth-Sun system scientific research, technology, and applications projects. The relationships between NASA programs and project sponsors are also captured in this database. Both the PNKB and the RPKB will be integrated with an existing, evolving model of the NASA Earth Science Enterprise using an enterprise architecture modeling and

  11. 超声波对脱气与未脱气氯化铵溶液结晶的影响%Influence of ultrasonic waves on crystallization of ammonium chloride solution and degassed solution

    Institute of Scientific and Technical Information of China (English)

    余德洋; 刘宝林; 吕福扣

    2012-01-01

    In order to clarify the enhancement mechanism of saturated solution crystallization by ultrasound, the effects of ultrasonic waves on crystallization process of saturated ammonium chloride solution and degassed solution are investigated by using a novel ultrasonic cold stage device. The results show that the use of ultrasound could accelerate the crystallization process of both ammonium chloride solution and degassed solution, but the cooling rate and cloudiness time of ammonium chloride solution are much less than those of degassed solution. Furthermore, sonocrystallisation of ammonium chloride solution can result in smaller crystals than those induced by sonocrystallisation of degassed solution. It is concluded that cavitation and fluctuations of density, energy and temperature induced by ultrasound are factors that affect the crystallization process of saturated solutions. But cavitation is a major factor for the enhancement of saturated solution crystallization.%为了阐明超声波强化饱和溶液结晶的机理,分别研究了超声波对脱气饱和氯化铵溶液与未脱气饱和氯化铵溶液结晶的影响.结果显示,在相同超声波辐射下,脱气饱和氯化铵溶液与未脱气饱和氯化铵溶液的结晶均得到了强化,但未脱气饱和氯化铵溶液白浊化开始时间显著小于脱气饱和氯化铵溶液白浊化开始时间,未脱气氯化铵溶液结晶晶粒比脱气氯化铵溶液结晶晶粒更细小.这表明超声空化以及声场中溶液分子振动引起的能量、温度及密度的波动对饱和溶液的结晶均有影响,但空化是强化饱和溶液结晶的主要因素.

  12. Nanoclays: Two-dimensional shuttles for rare earth complexes in aqueous solution

    Science.gov (United States)

    Lezhnina, M. M.; Bentlage, M.; Kynast, U. H.

    2011-08-01

    Nanoclays are shown to be attractive substrates in at least two major respects. Firstly, Hectorite analogous commercial clays ("Laponite") can facilitate the usage of luminescent rare earth ions in aqueous solution, as their adherence to the clay surface strongly reduces water coordination and thus enables dramatically improved emission intensities. This also holds true for complexes of Tb 3+, which coordinate water in their native crystalline state, as demonstrated for tris(bipyiridine) complexes. For these, the laponite interaction affords a 16-fold gain in emission intensity in aqueous solution over the dissolved complex. Secondly, the two-dimensional, disk-like morphology of the clays enables a sufficient proximity of Ce 3+ and Tb 3+ to allow an energy transfer even at comparably low solution concentrations. In partially laminated, solid powders the efficiencies of the corresponding interlayer species decrease due to intimate interactions with the surrounding silicate and interlayer water, which can, however be counteracted by keeping the disks apart with long-chain, alkylammonium cations as spacers between the disks.

  13. Sulfuric acid recovery from rare earth sulphate solutions by diffusion dialysis

    Institute of Scientific and Technical Information of China (English)

    TANG Jian-jun; ZHOU Kang-gen; ZHANG Qi-xiu

    2006-01-01

    Sulfuric acid recovery from rare earth sulphate solutions by diffusion dialysis was studied. The mass transfer model of diffusion dialysis was established, the comparison between the experimental results and mathematical results was carried out, and the numerical analysis on the effects of operational parameters was studied. The results indicate that the derived mathematical model shows good quantitative relation between sulphuric acid recovery ratio and operational parameters, and the mathematical results agree with the experimental results well. The numerical analysis results indicate that it is appropriate to keep the ratio of water and feed flow rates, processing capacity per membrane area and recovery ratio of sulphuric acid to be 1, 20 L/(m2·d) and 0.7-0.8,respectively.

  14. Scientific Research for Integrated Solutions to Community Challenges: The Thriving Earth Exchange (TEX) Approach

    Science.gov (United States)

    Udu-gama, N.; Pandya, R.

    2015-12-01

    There is tremendous unmet and sometimes unrealized need for Earth and space science (ESS) expertise as part of civic decisions and local planning for climate change, natural hazards and natural resources. The Thriving Earth Exchange (TEX) helps AGU contribute that expertise to humanity in respectful, integrated ways. TEX brings ESS scientists together with local communities tackling issues of climate change, natural hazards and natural resources to co-design solutions that equitably integrate both scientific and community knowledge. To achieve this ambitious goal, TEX is partnering with organizations that are respected by and knowledgeable about communities both in the United States and internationally. Such partnerships include Rockefeller's 100 Resilient Cities Initiative, ICLEI USA, MIT's Climate Colab, among others. TEX works with these partners to approach communities who are ready to or already addressing ESS related issues. With partners, we help the communities define their goals, develop specific projects, and connect with relevant and helpful ESS scientists. We will also show how we help scientists and community leaders work productively together, and the tools we bring to support their innovation. It will highlight international examples, such as in the Pamir Mountains of Afghanistan-Tajikistan, Sri Lanka, and Ethiopia, and provide concrete examples of how these initiatives are helping TEX further expand the frontiers of collaborative research.

  15. Effect of varying nonwoven cotton substrate and the properties of the surfactant solution upon the adsorption of aqueous solutions of alkyl-dimethyl-benzyl-ammonium chloride

    Science.gov (United States)

    The adsorption of alkyl-dimethyl-benzyl-ammonium chloride (ADBAC), a cationic surfactant commonly employed as an antimicrobial agent, on greige, alkaline scoured, and bleached nonwoven cotton fabrics was investigated at varying surfactant concentrations and liquor ratios using UV-vis absorption spec...

  16. Reviewing innovative Earth observation solutions for filling science-policy gaps in hydrology

    Science.gov (United States)

    Lehmann, Anthony; Giuliani, Gregory; Ray, Nicolas; Rahman, Kazi; Abbaspour, Karim C.; Nativi, Stefano; Craglia, Massimo; Cripe, Douglas; Quevauviller, Philippe; Beniston, Martin

    2014-10-01

    Improved data sharing is needed for hydrological modeling and water management that require better integration of data, information and models. Technological advances in Earth observation and Web technologies have allowed the development of Spatial Data Infrastructures (SDIs) for improved data sharing at various scales. International initiatives catalyze data sharing by promoting interoperability standards to maximize the use of data and by supporting easy access to and utilization of geospatial data. A series of recent European projects are contributing to the promotion of innovative Earth observation solutions and the uptake of scientific outcomes in policy. Several success stories involving different hydrologists' communities can be reported around the World. Gaps still exist in hydrological, agricultural, meteorological and climatological data access because of various issues. While many sources of data exists at all scales it remains difficult and time-consuming to assemble hydrological information for most projects. Furthermore, data and sharing formats remain very heterogeneous. Improvements require implementing/endorsing some commonly agreed standards and documenting data with adequate metadata. The brokering approach allows binding heterogeneous resources published by different data providers and adapting them to tools and interfaces commonly used by consumers of these resources. The challenge is to provide decision-makers with reliable information, based on integrated data and tools derived from both Earth observations and scientific models. Successful SDIs rely therefore on various aspects: a shared vision between all participants, necessity to solve a common problem, adequate data policies, incentives, and sufficient resources. New data streams from remote sensing or crowd sourcing are also producing valuable information to improve our understanding of the water cycle, while field sensors are developing rapidly and becoming less costly. More recent data

  17. Thick pure palladium film with varied crystal structure electroless deposited from choline chloride–palladium chloride solution without the addition of reductant

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yurong; Li, Wei; Wang, Wenchang [School of Petrochemical Engineering, Key Laboratory of Fine Petrochemicals of Jiangsu Province, Changzhou University, Changzhou 213164 (China); Mitsuzak, Naotoshi [Qualtec Co., Ltd, Osaka 590-0906 (Japan); Bao, Weiliang [Department of Chemistry, Zhejiang University, Hanghzou 310058 (China); Chen, Zhidong, E-mail: chen13775646759@hotmail.com [School of Petrochemical Engineering, Key Laboratory of Fine Petrochemicals of Jiangsu Province, Changzhou University, Changzhou 213164 (China); School of Material Science and Engineering, Jiangsu Key Laboratory of Material Surface Technology, Changzhou University, Changzhou 213164 (China)

    2015-07-01

    Immersion deposition procedure was applied to achieve thick pure palladium films with thickness up to about 3 μm from choline chloride (ChCl)–palladium chloride (PdCl{sub 2}) aqueous solution without addition of reductant at 60 °C. Using X-ray diffraction and scanning electron microscope, it was confirmed that Pd films with different crystal orientations and morphology were obtained just by varying the immersion time, and Pd (111) crystal orientation predominated over other crystal orientations during the initial deposition procedure, while (220) conquered (111) about 45 min later. ChCl performing as a reductant facilitated the growth of thick Pd film free of reductant. The immersion deposition of Pd followed the mechanism of replacement reaction accompanying with autocatalyzed reaction and autocatalyzed reaction predominating over replacement reaction. The results revealed that Pd films prepared from ChCl–PdCl{sub 2} solution had excellent properties on solderability and corrosion resistance. - Highlights: • Thick pure Pd film was obtained from ChCl–PdCl{sub 2} aqueous solution without reductant. • Different crystal orientations and morphology of Pd films were achieved. • Immersion time determined the morphology of Pd films. • The mechanism of sustained deposition of Pd on Ni–P surface was deduced.

  18. Apparent and partial molar volumes of long-chain alkyldimethylbenzylammonium chlorides and bromides in aqueous solutions at T=15 deg. C and T=25 deg. C[Alkyldimethylbenzylammonium chlorides; Alkyldimethylbenzylammonium bromides; Micellization; Density; Apparent molar volumes

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Perez, A.; Ruso, J.M.; Nimo, J.; Rodriguez, J.R. E-mail: fmjulio@usc.es

    2003-12-01

    Density measurements of dodecyl- (C{sub 12}DBACl), tetradecyl- (C{sub 14}DBACl), hexadecyldimethylbenzylammonium chloride (C{sub 16}DBACl) and of decyl- (C{sub 10}DBABr) and dodecyldimethylbenzylammonium bromide (C{sub 12}DBABr) in aqueous solutions at T=15 deg. C and T=25 deg. C have been carried out. From these results, apparent and partial molar volumes were calculated. Positive deviations from the Debye-Hueckel limiting law provide evidence for limited association at concentrations below the critical micelle concentration. The change of the apparent molar volume upon micellization was calculated. The relevant parameters have been presented in function of the alkyl chain length. Apparent molar volumes of the present compounds in the micellar phase, V{sub phi}{sup m}, and the change upon micellization, {delta}V{sub phi}{sup m}, have been discussed in terms of temperature and type of counterion.

  19. Exact solution of earth-flattening transformation for P-SV waves: Taking surface wave as an example

    Institute of Scientific and Technical Information of China (English)

    HUANG Hui; CHEN Xiao-fei

    2008-01-01

    Taking surface wave as an example this paper proposes an exact solution of earth-flattening transformation for P-SV waves and discusses the applicability of the approximate methods. The results show that the transform parameter m has little influence on the final results, and on the condition of short wave approximation, approximate earth-flattening transformation is suitable. Moreover, the efficiency of approximate transformation is twice of that of exact transformation. For low frequency problems exact earth-flattening transformation should be used.

  20. 3-phenyl-4-acyl-5-isoxazolones as reagents for liquid-liquid extraction of tetravalent zirconium and hafnium from acidic chloride solutions

    OpenAIRE

    Reddy,B. Ramachandra; Kumar,J. Rajesh; Reddy,A. Varada

    2006-01-01

    Liquid liquid extraction of tetravalent zirconium and hafnium from acidic chloride solutions has been investigated using 3-phenyl-4-acyl-5-isoxazolones in xylene such as 3-phenyl-4-benzoyl-5-isoxazolones (HPBI), 3-phenyl-4-(4-fluorobenzoyl)-5-isoxazolone (HFBPI) and 3-phenyl-4-(4-toluoyl)-5-isoxazolone (HTPI). The extraction of zirconium(IV) / hafnium(IV) shows a ion exchange mechanism: MO2+ (aq) + 2 HA (org) « MOA2 (org) + 2 H+(aq), where M = Zr(IV) / Hf(IV) and HA = HPBI or HFBPI or H...

  1. Solution behavior of iron(III-N,N'-ethylene-bis-(salicylideneiminato-chloride in aqueous methanol at 298.15, 303.15 and 313.15K

    Directory of Open Access Journals (Sweden)

    Brahman Dhiraj

    2014-01-01

    Full Text Available In this study partial molar volumes (φV0 and viscosity B-coefficients of iron(III-N, N'-ethylene-bis(salicylideneiminato-chloride, abbreviated as FeIII(salenCl, in different aqueous methanol solutions were determined from solution density and viscosity measurements at temperatures 298.15, 303.15, and 313.15 K under ambient pressure. Apparent molar volumes (φV and densities (ρ were used to calculate the apparent molar expansibilities (φE, the partial molar expansibilities (φE0 and the temperature dependence of the partial molar expansibilities (φE0 at constant pressure, (δφE0/δTP of FeIII(salenCl solutions to reveal the nature of different interactions in the ternary solutions. The transition state theory was applied to analyze the viscosity B-coefficients on the basis of the activation parameters of viscous flow. The overall results indicated strong solute-solvent interactions between FeIII(salenCl and the solvent molecules, preferentially with water molecules and that FeIII(salenCl acts as a net structure promoter in the ternary solutions. UV-VIS absorption spectra of the ternary solutions also stand in support of the results obtained.

  2. Photocatalytic Degradation of Methyl Thionine Chloride in Aqueous Solution over Nanometer ( CdS/TiO2 )/MCM-41

    Institute of Scientific and Technical Information of China (English)

    XUE Hanling; LI Jianwei; GE Lingmei

    2006-01-01

    ( CdS / TiO2 )/MCM-41 loaded nanometer photocatalyst was prepared by the sol-gel method and dipping process, the photocatalytic degradation of methyl thionine chloride in water was investigated by using the photocatalyst. The experimental results show that the optimum concentration of CdS over TiO2 was 3% ( molar ratio ), the photocatalytic activity was enhanced when making TiO2 the anatase phase with a rise of the roasting temperature, and the carrier, mesoporous molecular sieve MCM- 41, was beneficial to improving the photocatalytic activity of TiO2 for photocatalytic degradation of methyl thionine chloride. The morphology and the crystalline phase of the photocatalyst were discussed by means of XRD and SEM techniques, and the reaction mechanism of catalytic properties was also discussed.

  3. Cyberinfrastructure at IRIS: Challenges and Solutions Providing Integrated Data Access to EarthScope and Other Earth Science Data

    Science.gov (United States)

    Ahern, T. K.; Barga, R.; Casey, R.; Kamb, L.; Parastatidis, S.; Stromme, S.; Weertman, B. T.

    2008-12-01

    While mature methods of accessing seismic data from the IRIS DMC have existed for decades, the demands for improved interdisciplinary data integration call for new approaches. Talented software teams at the IRIS DMC, UNAVCO and the ICDP in Germany, have been developing web services for all EarthScope data including data from USArray, PBO and SAFOD. These web services are based upon SOAP and WSDL. The EarthScope Data Portal was the first external system to access data holdings from the IRIS DMC using Web Services. EarthScope will also draw more heavily upon products to aid in cross-disciplinary data reuse. A Product Management System called SPADE allows archive of and access to heterogeneous data products, presented as XML documents, at the IRIS DMC. Searchable metadata are extracted from the XML and enable powerful searches for products from EarthScope and other data sources. IRIS is teaming with the External Research Group at Microsoft Research to leverage a powerful Scientific Workflow Engine (Trident) and interact with the web services developed at centers such as IRIS to enable access to data services as well as computational services. We believe that this approach will allow web- based control of workflows and the invocation of computational services that transform data. This capability will greatly improve access to data across scientific disciplines. This presentation will review some of the traditional access tools as well as many of the newer approaches that use web services, scientific workflow to improve interdisciplinary data access.

  4. Effect of Solution pH and Chloride Concentration on Akaganeite Precipitation: Implications for Akaganeite Formation on Mars

    Science.gov (United States)

    Peretyazhko, T. A.; Rampe, E. B.; Clark, J. V.; Archer, P. D., Jr.; Morris, R. V.; Ming, D. V.

    2017-01-01

    Akaganeite (Beta-FeOOH, chloride-containing Fe(III) (hydr)oxide) has been recently discovered on the surface of Mars by the Mars Science Laboratory Curiosity rover in Yellowknife Bay, Gale Crater, Mars [1] and from orbit by the Mars Reconnaissance Orbiter in Robert Sharp crater and Antoniadi basin [2]. However, the mechanism and aqueous environmental conditions of akaganeite formation (e.g., pH and chloride concentration) remain unknown. We have investigated formation of akaganeite through Fe(III) hydrolysis at variable initial pH and chloride concentrations. The formed Fe(III) precipitates were characterized by instruments similar to instruments on Mars robotic spacecraft. Syntheses were performed through hydrolysis of Fe(III) perchlorate with addition of Na cloride (Fe/Cl ratio between 0.5 and 5) and at initial pH of 1.5, 2, 4, 6 and 8 at 90degC. X-ray diffraction analysis revealed formation of akaganeite alone or in mixture with goethite, hematite and ferrihydrite at all initial pHs and Fe/Cl ratio between 0.5 and 2 while akaganeite precipitated only at pH 1.5 and Fe/Cl greater than2. Chloride content of akaganeite was affected by initial pH and decreased from 20-60 mg/g at pH 1.5 to less than 0.1 mg/g at pH 8. The synthesized akaganeite samples were also characterized by Mössbauer and infrared spectroscopy and volatiles were analysed by thermal and evolved gas analysis. The obtained characterization data will be compared to published data from rover and orbital missions [1-3] to determine martian akaganeite composition, crystallinity and formation conditions.

  5. Sodium Chloride interaction with solvated and crystalline cellulose : sodium ion affects the tetramer and fibril in aqueous solution

    OpenAIRE

    Bellesia, Giovanni; Gnanakaran, S.

    2013-01-01

    Inorganic salts are a natural component of biomass which have a significant effect on the product yields from a variety of biomass conversion processes. Understanding their effect on biomass at the microscopic level can help discover their mechanistic role. We present a study of the effect of aqueous sodium chloride (NaCl) on the largest component of biomass, cellulose, focused on the thermodynamic and structural effect of a sodium ion on the cellulose tetramer, and fibril. Replica exchange m...

  6. Big Data challenges and solutions in building the Global Earth Observation System of Systems (GEOSS)

    Science.gov (United States)

    Mazzetti, Paolo; Nativi, Stefano; Santoro, Mattia; Boldrini, Enrico

    2014-05-01

    The Group on Earth Observation (GEO) is a voluntary partnership of governments and international organizations launched in response to calls for action by the 2002 World Summit on Sustainable Development and by the G8 (Group of Eight) leading industrialized countries. These high-level meetings recognized that international collaboration is essential for exploiting the growing potential of Earth observations to support decision making in an increasingly complex and environmentally stressed world. To this aim is constructing the Global Earth Observation System of Systems (GEOSS) on the basis of a 10-Year Implementation Plan for the period 2005 to 2015 when it will become operational. As a large-scale integrated system handling large datasets as those provided by Earth Observation, GEOSS needs to face several challenges related to big data handling and big data infrastructures management. Referring to the traditional multiple Vs characteristics of Big Data (volume, variety, velocity, veracity and visualization) it is evident how most of them can be found in data handled by GEOSS. In particular, concerning Volume, Earth Observation already generates a large amount of data which can be estimated in the range of Petabytes (1015 bytes), with Exabytes (1018) already targeted. Moreover, the challenge is related not only to the data size, but also to the large amount of datasets (not necessarily having a big size) that systems need to manage. Variety is the other main challenge since datasets coming from different sensors, processed for different use-cases are published with highly heterogeneous metadata and data models, through different service interfaces. Innovative multidisciplinary applications need to access and use those datasets in a harmonized way. Moreover Earth Observation data are growing in size and variety at an exceptionally fast rate and new technologies and applications, including crowdsourcing, will even increase data volume and variety in the next future

  7. Rural Single Wire Earth Return distribution networks - Associated problems and cost-effective solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hosseinzadeh, N. [Swinburne University of Technology, PO Box 218, Hawthorn, Vic 3122 (Australia); Mayer, J.E. [Aurecon Australia Pty Ltd., Brisbane (Australia); Wolfs, P.J. [Curtin University of Technology, Perth (Australia)

    2011-02-15

    Single Wire Earth Return (SWER) systems are used for supplying electricity at low cost, where electricity supply is required for small populations of people dispersed across wide geographical areas. It is principally used for rural electrification, but is also used for other isolated loads and light rail. The existing SWER distribution systems have been stretched with the sharp growth of their loads because of customers' change of lifestyle, which has introduced additional load of air conditioning equipment, motors driven by variable-speed drives and inverters. This paper proposes cost-effective solutions to address the problem of voltage regulation and compensation of the unbalancing effect of SWER lines on the three-phase feeder of these lines, which have been exacerbated by this load growth. To improve the voltage regulation problem, a LV switchable reactor has been designed, a prototype made and tested in the field. Also, an unbalance compensator has been designed to reduce the unbalancing effect of SWER lines. Two case networks have been used to perform simulation studies on the effectiveness of both proposed solutions. At first, a case study is used to demonstrate the impact of a switchable reactor on improving voltage regulation. Then, another case study shows that installation of a switchable reactor and an unbalance compensator simultaneously on a SWER distribution system effectively improves voltage regulation and reduces unbalancing effects. (author)

  8. Corrosion Penetration and Crystal Structure of AA5022 in HCl Solution and Rare Earth Elements

    Institute of Scientific and Technical Information of China (English)

    A.A.El-Meligi; S.H. Sanad; A.A.Ismail; A.M. Baraka

    2005-01-01

    Al-alloy (AA5022) corrosion penetration (CP) and crystal structure were investigated after running static immersion corrosion tests in 1 mol/L HCl solution and different concentrations of rare earth elements (La3+), (Ce3+) and their combination, at different temperatures. X-ray diffraction (XRD) was used to examine the surface structure before and after immersion, and secondary electron detector (SED) was operated to study surface morphology. In 1 mol/L HCl solution the corrosion penetration increased with increasing temperature and immersion time. The increase of La3+ concentrations up to 1000× 10-6 g/L led to the decrease in the corrosion penetration, and the decrease in Ce3+concentrations up to 50×10-6 g/L decreases the corrosion penetration of the alloy. Mix3 (combination of La3+ and Ce3+) dramatically reduced the corrosion penetration. This suggests that a synergistic effect exists between La3+and Ce3+. The reaction kinetics both in absence and presence of La3+ and Ce3+ and their combination would follow a parabolic rate law. The XRD patterns revealed that the intensities of certain hkl phases are affected. The crystalline structure has not been deformed either before or after testing and there are no additional peaks except that of the as-received alloy. In the case of accelerating CP, the surface morphology shows that the roughness andvoids of surface are increased.

  9. Rheological behaviour of some saccharides in aqueous potassium chloride solutions over temperature range (288.15 to 318.15) K

    Energy Technology Data Exchange (ETDEWEB)

    Banipal, Parampaul K., E-mail: pkbanipal@yahoo.co [Department of Chemistry, Guru Nanak Dev University, Amritsar 143005 (India); Chahal, Amanpreet K.; Singh, Vickramjeet [Department of Chemistry, Guru Nanak Dev University, Amritsar 143005 (India); Banipal, Tarlok S. [Department of Applied Chemistry, Guru Nanak Dev University, Amritsar 143005 (India)

    2010-08-15

    The viscosities, {eta} of mono-, di-, tri-saccharides and methylglycosides, viz., D(+)-xylose (XYL), D(-)-arabinose (ARA), D(-)-ribose (RIB), D(-)-fructose (FRU), D(+)-galactose (GAL), D(+)-mannose (MAN), D(+)-glucose (GLU), D(+)-melibiose (MEL), D(+)-cellobiose (CEL), D(+)-lactose monohydrate (LAC), D(+)-maltose monohydrate (MAL), D(+)-trehalose dihydrate (TRE), sucrose (SUC), D(+)-raffinose pentahydrate (RAF), {alpha}-methyl-D(+)-glucoside ({alpha}-Me-GLU), methyl-{alpha}-D-xylopyranoside (Me-{alpha}-XYL), and methyl-{beta}-D-xylopyranoside (Me-{beta}-XYL) in water and in (0.5, 1.0, 2.0, and 3.0) mol . kg{sup -1} aqueous solutions of potassium chloride (KCl) have been determined at T = (288.15, 298.15, 308.15, and 318.15) K from efflux time measurements by using a capillary viscometer. Densities used to determine viscosities have been reported earlier. The viscosity data have been utilized to determine the viscosity B-coefficients employing the Jones-Dole equation at different temperatures. From these data, the viscosity B-coefficients of transfer, {Delta}{sub t}B have been estimated for the transfer of various saccharides/methylglycosides from water to aqueous potassium chloride solutions. The {Delta}{sub t}B values have been found to be positive, whose magnitude increases with the increase in concentration of potassium chloride in all cases. The dB/dT coefficients, pair, {eta}{sub AB} and triplet, {eta}{sub ABB} viscometric interaction coefficients have also been determined. Gibbs free energies of activation and related thermodynamic parameters of activation of viscous flow have been determined employing Feakin's transition-state theory. The signs and magnitudes of various parameters have been discussed in terms of solute-solute and solute-solvent interactions occurring in these solutions. The effect of substitution of -OH by methoxy group, -OCH{sub 3} has also been discussed.

  10. Integrated solution for the complete remote sensing process - Earth Observation Mission Control Centre (EOMC2)

    Science.gov (United States)

    Czapski, Paweł

    2016-07-01

    We are going to show the latest achievements of the Remote Sensing Division of the Institute of Aviation in the area of remote sensing, i.e. the project of the integrated solution for the whole remote sensing process ranging from acquiring to providing the end user with required information. Currently, these tasks are partially performed by several centers in Poland, however there is no leader providing an integrated solution. Motivated by this fact, the Earth Observation Mission Control Centre (EOMC2) was established in the Remote Sensing Division of the Institute of Aviation that will provide such a comprehensive approach. Establishing of EOMC2 can be compared with creating Data Center Aerial and Satellite Data Centre (OPOLIS) in the Institute of Geodesy and Cartography in the mid-70s in Poland. OPOLIS was responsible for broadly defined data processing, it was a breakthrough innovation that initiated the use of aerial image analysis in Poland. Operation center is a part of the project that will be created, which in comparison with the competitors will provide better solutions, i.e.: • Centralization of the acquiring, processing, publishing and archiving of data, • Implementing elements of the INSPIRE directive recommendations on spatial data management, • Providing the end-user with information in the near real-time, • Ability of supplying the system with images of various origin (aerial, satellite, e.g. EUMETCast, Sentinel, Landsat) and diversity of telemetry data, data aggregation and using the same algorithms to images obtained from different sources, • System reconfiguration and batch processing of large data sets at any time, • A wide range of potential applications: precision agriculture, environmental protection, crisis management and national security, aerial, small satellite and sounding rocket missions monitoring.

  11. The inhibitive mechanisms of nitrite and molybdate anions on initiation and propagation of pitting corrosion for mild steel in chloride solution

    Science.gov (United States)

    Zhou, Yong; Zuo, Yu

    2015-10-01

    The inhibitive mechanism of NO2- and MoO42- on the initiation and propagation of pitting corrosion for mild steel in chloride solution was studied with electrochemical methods and X-ray photoelectron spectroscopy (XPS). In 0.1 M NaCl solution both the addition of 0.2 M NaNO2 and 0.2 M Na2MoO4 effectively promoted passivation of mild steel. The passive film on the steel surface formed in NaCl + NO2- solution was composed of mainly γ-Fe2O3, and the film formed in NaCl + MoO42- solution was composed of two components: one is Fe2(MoO4)3 and the other is an oxide composed of Fe and O. The film formed in NaNO2 solution has lower oxygen vacancies and larger impedance than the film formed in Na2MoO4 solution. NO2- shows better inhibition to the initiation of pitting corrosion than MoO42-, which is attributed to its strong oxidability that results in the formation of a stable γ-Fe2O3 film. However, in NaNO2 solution, once a pit forms, it is more difficult to get repassivated than the situation in Na2MoO4 solution. The main reason is due to that in a propagating pit MoO42- anions result in increased solution pH value, but conversely NO2- anions lead to a decreased solution pH value within a pit.

  12. Potassium chloride and rare earth elements improve plant growth and increase the frequency of the Agrobacterium tumefaciens-mediated plant transformation.

    Science.gov (United States)

    Boyko, Alex; Matsuoka, Aki; Kovalchuk, Igor

    2011-04-01

    Plant transformation efficiency depends on the ability of the transgene to successfully interact with plant host factors. Our previous work and the work of others showed that manipulation of the activity of host factors allows for increased frequency of transformation. Recently we reported that exposure of tobacco plants to increased concentrations of ammonium nitrate increases the frequency of both homologous recombination and plant transgenesis. Here we tested the influence of KCl and salts of rare earth elements, Ce and La on the efficiency of Agrobacterium-mediated plant transformation. We found that exposure to KCl, CeCl(3) and LaCl(3) leads to an increase in recombination frequency in Arabidopsis and tobacco. Plants grown in the presence of CeCl(3) and LaCl(3) had higher biomass, longer roots and greater root number. Analysis of transformation efficiency showed that exposure of tobacco plants to 50 mM KCl resulted in ~6.0-fold increase in the number of regenerated calli and transgenic plants as compared to control plants. Exposure to various concentrations of CeCl(3) showed a maximum increase of ~3.0-fold in both the number of calli and transgenic plants. Segregation analysis showed that exposure to KCl and cerium (III) chloride leads to more frequent integrations of the transgene at a single locus. Analysis of transgene intactness showed better preservation of right T-DNA border during transgene integration. Our data suggest that KCl and CeCl(3) can be effectively used to improve quantity and quality of transgene integrations.

  13. Effect of chloride ion on corrosion behavior of SUS316L-grade stainless steel in nitric acid solutions containing seawater components under γ-ray irradiation

    Science.gov (United States)

    Sano, Y.; Ambai, H.; Takeuchi, M.; Iijima, S.; Uchida, N.

    2017-09-01

    Concerning the Fukushima Daiichi nuclear power plant accident, we investigated the effect of chloride ion on the corrosion behavior of SUS316L stainless steel, which is a typical material for the equipment used in reprocessing, in HNO3 solution containing seawater components, including under γ-ray irradiation condition. Electrochemical and immersion tests were carried out using a mixture of HNO3 and artificial seawater (ASW). In the HNO3 solution containing high amounts of ASW, the cathodic current densities increased and uniform corrosion progressed. This might be caused by strong oxidants, such as Cl2 and NOCl, generated in the reaction between HNO3 and Cl- ions. The corrosion rate decreased with the immersion time at low concentrations of HNO3, while it increased at high concentrations. Under γ-ray irradiation condition, the corrosion rate decreased due to the suppression of the cathodic reactions by the reaction between the above oxidants and HNO2 generated by radiolysis.

  14. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  15. Antimicrobial properties of titanium soaked with benzalkonium chloride solution%纯钛经苯扎氯铵浸泡后的抗菌性能的研究

    Institute of Scientific and Technical Information of China (English)

    李佳; 廉云敏; 高岚

    2015-01-01

    Objective:To study the antibacterial properties of pure titanium treated with benzalkonium chloride solution.Meth-ods:10 mm ×10 mm ×1 mm titanium specimens were processed by the benzalkonium chloride solution at 1%,0.5% and 0.1%respectively followed by treatment in the cultured bacterial suspension,and then the antibacterial properties of the titanium plates were examined.Additionally,the thermal cycling test was carried out for the 1% benzalkonium chloride-treated titanium plates, and subsequently put the plates into cultured bacterial suspension,the duration of antibacterial properties was observed.Results:0.5% and 1% benzalkonium chloride solution-treated titanium plates significantly inhibited the growth of candida albicans(P <0. 05),1% solution was more effective than 0.5% solution.After 1 000 and 2 500 thermal cycling,the pure titanium still retained the antibacterial ability,but the plates treated by 5 000 cycling showed no antibacterial effect.Conclusion:A certain concentration of benzalkonium chloride can make the pure titanium obtain antibacterial properties.The treated plates may maintain the antibacte-rial properties for a minimum of 3 months.%目的:通过用苯扎氯铵溶液浸泡处理钛片,了解该方法能否使纯钛具有抗菌性及抗菌性持续的时间。方法:制作10 mm ×10 mm ×1 mm 的钛片试件,用不同浓度的苯扎氯铵溶液浸泡处理,菌悬液浸泡培养,检测有无抗菌性。用1%的苯扎氯铵溶液浸泡处理试件,进行冷热循环实验后再进行细菌培养,检测抗菌性的持续时间。结果:不同浓度的苯扎氯铵溶液处理纯钛后对白色念珠菌生长的抑制效果不同,0.5%和1%的苯扎氯铵溶液浸泡纯钛可使其产生抗菌性(均有显著差异,P <0.05),1%的苯扎氯铵溶液效果更佳。冷热循环1000次和2500次后纯钛仍具有抗菌性,5000次时与未进行抗菌处理效果相同。结论:一定浓度的苯扎氯铵

  16. Solution-Processed Rare-Earth Oxide Thin Films for Alternative Gate Dielectric Application.

    Science.gov (United States)

    Zhuang, Jiaqing; Sun, Qi-Jun; Zhou, Ye; Han, Su-Ting; Zhou, Li; Yan, Yan; Peng, Haiyan; Venkatesh, Shishir; Wu, Wei; Li, Robert K Y; Roy, V A L

    2016-11-16

    Previous investigations on rare-earth oxides (REOs) reveal their high possibility as dielectric films in electronic devices, while complicated physical methods impede their developments and applications. Herein, we report a facile route to fabricate 16 REOs thin insulating films through a general solution process and their applications in low-voltage thin-film transistors as dielectrics. The formation and properties of REOs thin films are analyzed by atomic force microscopy (AFM), X-ray diffraction (XRD), spectroscopic ellipsometry, water contact angle measurement, X-ray photoemission spectroscopy (XPS), and electrical characterizations, respectively. Ultrasmooth, amorphous, and hydrophilic REO films with thickness around 10 nm have been obtained through a combined spin-coating and postannealing method. The compositional analysis results reveal the formation of RE hydrocarbonates on the surface and silicates at the interface of REOs films annealed on Si substrate. The dielectric properties of REO films are investigated by characterizing capacitors with a Si/Ln2O3/Au (Ln = La, Gd, and Er) structure. The observed low leakage current densities and large areal capacitances indicate these REO films can be employed as alternative gate dielectrics in transistors. Thus, we have successfully fabricated a series of low-voltage organic thin-film transistors based on such sol-gel derived REO films to demonstrate their application in electronics. The optimization of REOs dielectrics in transistors through further surface modification has also been studied. The current study provides a simple solution process approach to fabricate varieties of REOs insulating films, and the results reveal their promising applications as alternative gate dielectrics in thin-film transistors.

  17. Felyx : A Free Open Software Solution for the Analysis of Large Earth Observation Datasets

    Science.gov (United States)

    Piolle, Jean-Francois; Shutler, Jamie; Poulter, David; Guidetti, Veronica; Donlon, Craig

    2014-05-01

    GHRSST project, by assembling large collections of earth observation data from various sources and agencies, has also raised the need for providing the user community with tools to inter-compare them, assess and monitor their quality. The ESA /Medspiration project, which implemented the first operating node of GHRSST system for Europe, also paved the way successfully towards such generic analytics tools by developing the High Resolution Diagnostic Dataset System (HR-DDS) and Satellite to In situ Multi-sensor Match-up Databases. Building on this heritage, ESA is now funding the development by IFREMER, PML and Pelamis of felyx, a web tool merging the two capabilities into a single software solution. It will consist in a free open software solution, written in python and javascript, whose aim is to provide Earth Observation data producers and users with an open-source, flexible and reusable tool to allow the quality and performance of data streams (satellite, in situ and model) to be easily monitored and studied. The primary concept of Felyx is to work as an extraction tool, subsetting source data over predefined target areas (which can be static or moving) : these data subsets, and associated metrics, can then be accessed by users or client applications either as raw files, automatic alerts and reports generated periodically, or through a flexible web interface enabling statistical analysis and visualization. Felyx presents itself as an open-source suite of tools, written in python and javascript, enabling : * subsetting large local or remote collections of Earth Observation data over predefined sites (geographical boxes) or moving targets (ship, buoy, hurricane), storing locally the extracted data (refered as miniProds). These miniProds constitute a much smaller representative subset of the original collection on which one can perform any kind of processing or assessment without having to cope with heavy volumes of data. * computing statistical metrics over these

  18. Long-term cement corrosion in chloride-rich solutions relevant to radioactive waste disposal in rock salt - Leaching experiments and thermodynamic simulations

    Science.gov (United States)

    Bube, C.; Metz, V.; Bohnert, E.; Garbev, K.; Schild, D.; Kienzler, B.

    Low- and intermediate-level radioactive wastes are frequently solidified in a cement matrix. In a potential repository for nuclear wastes, the cementitious matrix is altered upon contact with solution and the resulting secondary phases may provide for significant retention of the radionuclides incorporated in the wastes. In order to assess the secondary phases formed upon corrosion in chloride-rich solutions, which are relevant for nuclear waste disposal in rock salt, leaching experiments were performed. Conventional laboratory batch experiments using powdered hardened cement paste in MgCl2-rich solutions were left to equilibrate for up to three years and full-scale cemented waste products were exposed to NaCl-rich and MgCl2-rich solutions for more than twenty years, respectively. Solid phase analyses revealed that corrosion of hardened cement in MgCl2-rich solutions advanced faster than in NaCl-rich solutions due to the extensive exchange of Mg from solution against Ca from the cementitious solid. Thermodynamic equilibrium simulations compared well to results at the final stages of the respective experiments indicating that close to equilibrium conditions were reached. At high cement product to brine ratios (>0.65 g mL-1), the solution composition in the laboratory-scale experiments was close to that of the full-scale experiments (cement to brine ratio of 2.5 g mL-1) in the MgCl2 systems. The present study demonstrates the applicability of thermodynamic methods used in this approach to adequately describe full-scale long-term experiments with cemented waste simulates.

  19. SCC of X-52 and X-60 weldements in diluted NaHCO{sub 3} solutions with chloride and sulfate ions

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Rodriguez, J.G.; Zeferino-Rodriguez, T. [UAEM-Centro de Investigacion en Ingenieria y Ciencias Aplicadas, Av. Universidad 1001, Col. Chamilpa 62210, Cuernavaca, Morelos (Mexico); Espinosa-Medina, M.A.; Angeles-Chavez, C. [Instituto Mexicano del Petroleo, Eje Central Lazaro Cardenas 152, Col. San Bartolo Atepehuacan, 07730 Mexico D. F. (Mexico)

    2007-08-15

    Stress corrosion cracking tests were performed in both X-52 and X-60 weldments in sodium bicarbonate (NaHCO{sub 3}) solutions at 50 C using the Slow Strain Rate Testing (SSRT) technique. Solution concentrations varied between 0.1 to 0.0001 M, and to simulate the NS-4 solution, chloride (Cl{sup -}) and/or sulfate (SO{sub 4}{sup 2-}) ions were added to the 0.01 M solution. Tests were complemented with hydrogen permeation measurements and polarization curves. It was found that the corrosion rate, taken as the corrosion current, I{sub corr}, was maximum in 0.01 M NaHCO{sub 3} and with additions of SO{sub 4}{sup 2-} ions. Higher or lower solution concentrations or additions of Cl{sup -} alone decreased the corrosion rate of the weldment. The SSC susceptibility, measured as the percentage reduction in area, was maximum in 0.01M NaHCO{sub 3}. Higher or lower solution concentrations of additions of Cl{sup -} or SO{sub 4}{sup 2-} decreased the SCC susceptibility of the weldment. The amount of hydrogen uptake for the weldment was also highest in 0.01 M NaHCO{sub 3} solution, but it was minimum with the addition of Cl{sup -} or SO{sub 4}{sup 2-} ions. Thus, the most likely mechanism for the cracking susceptibility of X-52 and X-60 weldments in diluted NaHCO{sub 3} solutions seems to be hydrogen-assisted anodic dissolution. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  20. Near Earth Objects and Cascading Effects from the Policy Perspective: Implications from Problem and Solution Definition

    Science.gov (United States)

    Lindquist, Eric

    2016-04-01

    The characterization of near-Earth-objects (NEOs) in regard to physical attributes and potential risk and impact factors presents a complex and complicates scientific and engineering challenge. The societal and policy risks and impacts are no less complex, yet are rarely considered in the same context as material properties or related factors. Further, NEO impacts are typically considered as discrete events, not as initial events in a dynamic cascading system. The objective of this contribution is to position the characterization of NEOs within the public policy process domain as a means to reflect on the science-policy nexus in regard to risks and multi-hazard impacts associated with these hazards. This will be accomplished through, first, a brief overview of the science-policy nexus, followed by a discussion of policy process frameworks, such as agenda setting and the multiple streams model, focusing events, and punctuated equilibrium, and their application and appropriateness to the problem of NEOs. How, too, for example, does NEO hazard and risk compare with other low probability, high risk, hazards in regard to public policy? Finally, we will reflect on the implications of alternative NEO "solutions" and the characterization of the NEO "problem," and the political and public acceptance of policy alternatives as a way to link NEO science and policy in the context of the overall NH9.12 panel.

  1. Sodium Chloride interaction with solvated and crystalline cellulose : sodium ion affects the tetramer and fibril in aqueous solution

    CERN Document Server

    Bellesia, Giovanni

    2013-01-01

    Inorganic salts are a natural component of biomass which have a significant effect on the product yields from a variety of biomass conversion processes. Understanding their effect on biomass at the microscopic level can help discover their mechanistic role. We present a study of the effect of aqueous sodium chloride (NaCl) on the largest component of biomass, cellulose, focused on the thermodynamic and structural effect of a sodium ion on the cellulose tetramer, and fibril. Replica exchange molecular dynamics simulations of a cellulose tetramer reveal a number of preferred cellulose-Na contacts and bridging positions. Large scale MD simulations on a model cellulose fibril find that Na+ perturbs the hydroxymethyl rotational state population and consequently disrupts the "native" hydrogen bonding network.

  2. The rare earth element geochemistry of acid-sulphate and acid-sulphate-chloride geothermal systems from Yellowstone National Park, Wyoming, USA

    Science.gov (United States)

    Lewis, Anita J.; Palmer, Martin R.; Sturchio, Neil C.; Kemp, Anthony J.

    1997-02-01

    Rare earth element (REE) concentrations have been determined by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) in acid-sulphate and acid-sulphate-chloride waters and the associated sinters and volcanic rocks from the Yellowstone National Park (YNP), Wyoming, USA, geothermal system. REE concentrations in the volcanic rocks range from 222 to 347 ppm; their chondite-normalised REE patterns are typical of upper continental crust, with LREE > HREE and negative Eu anomalies. Total REE concentrations in the fluids range from 3 to 1133 nmol kg -1 (≥ 162 ppm), and ΣREE concentrations in sinter are ≥ 181 ppm. REE abundances and patterns in drill core material from YNP indicate some REE mobility. Normalisation of REE concentrations in altered Lava Creek Tuff (LCT) from Y-12 drill core to REE concentrations in fresh LCT indicate that the REE overall have been depleted with the exception of Eu, which has been decoupled from the REE series and concentrated in the altered rocks. Relative to the host rocks the REE patterns of the fluids are variably depleted in HREEs and LREEs, and usually have a pronounced positive Eu anomaly. This decoupling of Eu from the REE suite suggests that (1) Eu has been preferentially removed either from the host rock glass or from the host rock minerals, or (2) the waters are from a high temperature or reducing environment where Eu 2+ is more soluble than the trivalent REEs. Since the latter is inconsistent with production of acid-sulphate springs in a low temperature, oxidising near-surface environment, we suggest that the positive Eu anomalies in the fluids result from preferential dissolution of a Eu-rich phase in the host rock. Spatial and temporal variations in major element chemistry and pH of the springs sampled from Norris Geyser Basin and Crater Hills accompany variations in REE concentrations and patterns of individual geothermal springs. These are possibly related to changes in subsurface plumbing, which results in variations in

  3. The Organism/Organic Exposure to Orbital Stresses (O/OREOS) satellite: radiation exposure in low-earth orbit and supporting laboratory studies of iron tetraphenylporphyrin chloride.

    Science.gov (United States)

    Cook, Amanda M; Mattioda, Andrew L; Ricco, Antonio J; Quinn, Richard C; Elsaesser, Andreas; Ehrenfreund, Pascale; Ricca, Alessandra; Jones, Nykola C; Hoffmann, Søren V

    2014-02-01

    We report results from the exposure of the metalloporphyrin iron tetraphenylporphyrin chloride (FeTPPCl) to the outer space environment, measured in situ aboard the Organism/Organic Exposure to Orbital Stresses nanosatellite. FeTPPCl was exposed for a period of 17 months (3700 h of direct solar exposure), which included broad-spectrum solar radiation (∼122 nm to the near infrared). Motivated by the potential role of metalloporphyrins as molecular biomarkers, the exposure of thin-film samples of FeTPPCl to the space environment in low-Earth orbit was monitored in situ via ultraviolet/visible spectroscopy and reported telemetrically. The space data were complemented by laboratory exposure experiments that used a high-fidelity solar simulator covering the spectral range of the spaceflight measurements. We found that thin-film samples of FeTPPCl that were in contact with a humid headspace gas (0.8-2.3% relative humidity) were particularly susceptible to destruction upon irradiation, degrading up to 10 times faster than identical thin films in contact with dry headspace gases; this degradation may also be related to the presence of oxides of nitrogen in those cells. In the companion terrestrial experiments, simulated solar exposure of FeTPPCl films in contact with either Ar or CO2:O2:Ar (10:0.01:1000) headspace gas resulted in growth of a band in the films' infrared spectra at 1961 cm(-1). We concluded that the most likely carriers of this band are allene (C3H4) and chloropropadiene (C3H3Cl), putative molecular fragments of the destruction of the porphyrin ring. The thin films studied in space and in solar simulator-based experiments show qualitatively similar spectral evolution as a function of contacting gaseous species but display significant differences in the time dependence of those changes. The relevance of our findings to planetary science, biomarker research, and the photostability of organic materials in astrobiologically relevant environments is

  4. Liquid-liquid extraction and separation of total rare earth (RE) metals from polymetallic manganese nodule leaching solution

    Institute of Scientific and Technical Information of China (English)

    PK Parhi; KH Park; CW Nam; JT Park

    2015-01-01

    The study on the solvent extraction for quantitative and selective separation of total rare earth metals from the polymetallic nodule leach liquor was investigated. The typical leach liquor bearing 0. 094 g/L total rare earth, 0. 23 g/L Mn, 0.697 g/L Cu, 0.2 g/L Fe, 0.01 g/L Co and 0.735 g/L Ni was subjected to the removal iron content by precipitation method using Ca(OH)2 at pH 3.95, prior to solvent extraction of rare earth metals. Three different organo-phosphoric acid reagents (D2EHPA, PC88A, Cyanex 272) were used to ascertain their performances and selectivity towards the loading of rare earth metals in presence of other base metals. Based on the results of eq. pH effect, the performances of above three extractants followed the order as:D2EHPA>PC88A>Cyanex 272. To ensure the absence of extraction of base metals (Cu, Co, Ni), the eq. pH of the solution was optimized at the level of 2.21, though higher rare earth metal extraction efficiency was observed at higher eq. pH with either of the extractants. The complete process flow diagram for substantial recovery of total rare earth was developed using D2EHPA. Extraction isotherm plot was constructed at A:O=12:1, 3-stages and pHe=2.21, using 0.8 mol/L D2EHPA and the predicted condition of this study was further confirmed by 6-Cycles Counter Current Simulation (CCS) study. The stripping of total rare earth from loaded organic phase (LO) was conducted using HCl solution. Mc-Cabe Thiele diagram study carried out at A:O=1:5 using 4 mol/L HCl showed that three theoretical stages were needed for quantitative stripping of total rare earth. The subsequent stripped solution resulted thus led to contain total rare earth of 5.6 g/L indicating a very high enrichment of total metals by solvent extraction (SX) process.

  5. Role of finite ionospheric conductivity on toroidal field line oscillations in the Earth's magnetosphere -- Analytic solutions

    Science.gov (United States)

    Bulusu, Jayashree; Sinha, A. K.; Vichare, Geeta

    2016-06-01

    An analytic solution has been formulated to study the role of ionospheric conductivity on toroidal field line oscillations in the Earth's magnetosphere. The effect of ionospheric conductivity is addressed in two limits, viz, (a) when conductance of Alfvén wave is much different from ionospheric Pedersen conductance and (b) when conductance of Alfvén wave is close to the ionospheric Pedersen conductance. In the former case, the damping is not significant and standing wave structures are formed. However, in the latter case, the damping is significant leading to mode translation. Conventionally, "rigid-end" and "free-end" cases refer to eigenstructures for infinitely large and vanishingly small limit of ionospheric conductivity, respectively. The present work shows that when the Pedersen conductance overshoots (undershoots) the Alfvén wave conductance, a free-end (rigid-end) mode gets transformed to rigid-end (free-end) mode with an increase (decrease) in harmonic number. This transformation takes place within a small interval of ionospheric Pedersen conductance around Alfvén wave conductance, beyond which the effect of conductivity on eigenstructures of field line oscillations is small. This regime of conductivity limit (the difference between upper and lower limits of the interval) decreases with increase in harmonic number. Present paper evaluates the damping effect for density index other than the standard density index m = 6, using perturbation technique. It is found that for a small departure from m = 6, both mode frequency and damping rate become a function of Pedersen conductivity.

  6. Solution-reaction Calorimetric Study of Coordination Compounds of Rare Earth Perchlorates with Alanine and Imidazole

    Institute of Scientific and Technical Information of China (English)

    ZHAO, Yan-Ru(赵艳茹); HOU, An-Xin(侯安新); DONG, Jia-Xin(董家新); ZHAO, Shun-Sheng(赵顺省); LIU, Yi(刘义); QU, Song-Sheng(屈松生)

    2004-01-01

    Two coordination compounds of rare earth perchlorates with alanine and imidazole, [RE(Ala)n(Im)(H2O)](ClO4)3(s) (RE=La, n=3; RE=Nd, n=2), have been prepared and characterized. The standard molar enthalpies of reaction for the following two reactions, LaCL·7H2O(s)+3Ala(s)+Im(s)+3NaClO4(s)=[La(Ala).(Im)(H2O)]-(ClO4)3(s)+3NaCl(s)+6H2O(I)(1)and NdCl3·6H2O(s)+2Ala(s)+2Ala(s)+Im(s)+3NaClO4(s)=[Nd(Ala)2(Im)(H2O)]-(ClO4)3(s)+3NaCl(s)+5H2O(l) (2), were determined by solution-reaction calorimetry, at T=298.15 K, as 36.168 ±0.642kJ·mol-1 and 48.590±0.934kJ·mol-1 respectively. From the results and other auxiliary quantities, the standard molar enthalpies of formation of [La(Ala)3(Im)(H2O)](ClO4)3(s) and [Nd(Ala)2(Im)(H2O)] (ClO4)3(s) were derived,△fH(-)m{[La(Ala).(Im)(H2O)](ClO4)3,s}=(-2984.8±1.0)kJ·mol-1 and △fH(-)m{[Nd(Ala).(Im)(H2O)]-(ClO4)3,s}=(-2387.8±0.8)kJ·mol-1, respectively.

  7. Cytotoxicity of five fluoroquinolone and two nonsteroidal anti-inflammatory benzalkonium chloride-free ophthalmic solutions in four corneoconjunctival cell lines

    Science.gov (United States)

    Ayaki, Masahiko; Iwasawa, Atsuo; Soda, Mitsutaka; Yaguchi, Shigeo; Koide, Ryohei

    2010-01-01

    Purpose: Epithelial disorders after eye surgery can result in visual deterioration and patient discomfort. Such disorders may be caused by drug toxicity. In the present study, we evaluated the toxicity of ophthalmic solutions, with or without benzalkonium chloride (BAK) as the preservative, used for postoperative care. Methods: A range of commercially available antibiotic and anti-inflammatory ophthalmic solutions used postoperatively (ie, levofloxacin, moxifloxacin, gatifloxacin, norfloxacin, tosufloxacin, dibekacin, cefmenoxime, diclofenac, bromfenac, pranoprofen, betamethasone, and fluoromethorone) were assessed in three corneal cell lines and one conjunctival cell line. All antibiotic solutions were BAK free. Cell viability was determined with the 3-(4,5-dimethyl-2 thiazoyl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) assay after cells had been exposed to the drugs for 48 h. The effects of preservatives on cell viability were also determined. Toxicity was compared using the cell viability score (CVS). Results: Based on results of the MTT assay and CVS, the order of cell viability after exposure to the antibiotic solutions was cefmenoxime ≥ tosufloxicin ≥ dibekacin ≥ levofloxacin ≥ norfloxacin = gatifloxacin = moxifloxacin. For the anti-inflammatory solutions, the order of cell viability was betamethasone ≥ betamethasone + fradiomycin > preservative-free diclofenac ≥ preservative-free bromfenac >> 0.02% fluoromethorone ≥ 0.1% fluoromethorone = diclofenac + preservative = bromfenac + preservative = pranoprofen. The anti-inflammatory drugs were more toxic than the antibiotics. The toxicity of antibiotic drugs against ocular surface cells was dependent on the pharmaceutical components of the solution, whereas that of the anti-inflammatory drugs was dependent on both the pharmaceutical components and the preservatives. Conclusion: Postoperative drug-induced epitheliopathy may be caused primarily by anti-inflammatory drugs. CVS is useful in comparing the

  8. A comparative electrochemical and quantum chemical calculation study of BTAH and BTAOH as copper corrosion inhibitors in near neutral chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Finsgar, Matjaz; Lesar, Antonija; Kokalj, Anton [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Milosev, Ingrid [Jozef Stefan Institute, Department of Physical and Organic Chemistry, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Valdoltra Orthopaedic Hospital, Jadranska c. 31, SI-6280 Ankaran (Slovenia)], E-mail: ingrid.milosev@ijs.si

    2008-11-30

    The inhibition of copper corrosion in 3% NaCl solution was studied by using a well-known inhibitor, benzotriazole (BTAH), and its not so extensively explored derivative, 1-hydroxybenzotriazole (BTAOH). Electrochemical methods, i.e., linear polarization, Tafel and potentiodynamic curve measurements and electrochemical quartz crystal microbalance (EQCM) measurements were used. Corrosion parameters and inhibition effectiveness were determined. Experimental results showed that benzotriazole is a more effective inhibitor of the corrosion of copper in chloride media than 1-hydroxybenzotriazole. Whereas in the presence of BTAH a protective Cu-BTA layer is formed on the Cu surface, in the presence of BTAOH a thick, poorly protective layer is formed, which readily dissolves in chloride solution. Kinetic parameters were calculated based on EQCM results. Adsorption of BTAOH follows a linear growth law, in contrast to BTAH, whose film growth can be best represented at first by a parabolic, and later by logarithmic, growth law. Different mechanisms of growth imply different mechanisms of inhibition and account for the different inhibition effectiveness. Density functional theory calculations were performed to characterize certain features of the molecular structures, including the electronic parameters related to the inhibition effectiveness of these inhibitors. Introduction of the -OH group into the benzotriazole molecules does not change their electronic parameters significantly neither in gas phase nor in the presence of water solvent. Other parameters, therefore, affect the inhibition effectiveness of these corrosion inhibitors. In particular, superior inhibition effectiveness of BTAH is attributed to interplay of planar molecular structure, physisorption and intermolecular H-bonding, which cooperatively may result in formation of thin and protective film on the surface.

  9. Mixed micellar properties of sodium n-octanoate(SOC) with n-octylammonium chloride(OAC) in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Byung Hwan [Korea University of Technology, Chonan (Korea, Republic of)

    2002-12-01

    The critical concentration(CMC) and the counterion binding constant(B) for the mixed micellization of sodium n-octanoate(SOC) with n-octylammonium chloride(OAC) were determined as a function of the overall mole fraction of SOC({alpha}{sub 1}). Various thermodynamic parameters(X{sub i}, {gamma}{sub i}, C{sub i}, a{sub i}{sup M}, and {delta}H{sub mix}) for the mixed micellization of the SOC/OAC systems have been calculated and analyzed by means of the equations derived from the nonideal mixed micellar model. The results show that there are great deviations from the ideal behavior for the mixed micellization of these systems. And other thermodynamic parameters({delta}G{sub m}{sup o}, {delta}H{sub m}{sup o}, and {delta}S{sub m}{sup o}) associated with the micellization of SOC, OAC, and their mixture({alpha}{sub 1}=0.5) have been also estimated from the temperature dependence of CMC and B values, and the significance of these parameters and their relation to the theory of the micelle formation have been considered and analyzed by comparing each other.

  10. Mechanism and toxicity research of benzalkonium chloride oxidation in aqueous solution by H2O2/Fe(2+) process.

    Science.gov (United States)

    Zhang, Qian; Xia, Yu-Feng; Hong, Jun-Ming

    2016-09-01

    As widely used disinfectants, the pollution caused by benzalkonium chloride (BAC) has attracted a lot of attention in recent years. Since it is not suitable for biodegradation, BAC was degraded firstly by Fenton advanced oxidation technologies (AOTs) in this research to enhance the biodegradability of the pollutions. The result revealed that the optimal molar ratio of H2O2/Fe(2+) for BAC degradation was 10:1, and the COD removal rate was 32 %. To clarify the pathway of degradation, the technique of GC-MS was implemented herein to identify intermediates and the toxicity of those BAC intermediates were also novelty tested through microbial fuel cells (MFC). The findings indicated that ten transformation products including benzyl dimethyl amine and dodecane were formed during the H2O2/Fe(2+) processes, which means the degradation pathway of BAC was initiated both on the hydrophobic (alkyl chain) and hydrophilic (benzyl and ammonium moiety) region of the surfactant. The toxicity of BAC before and after treated by Fenton process was monitored through MFC system. The electricity generation was improved 337 % after BAC was treated by H2O2/Fe(2+) oxidation processes which indicated that the toxicity of those intermediates were much lower than BAC. The mechanism and toxicity research in this paper could provide the in-depth understanding to the pathway of BAC degradation and proved the possibility of AOTs for the pretreatment of a biodegradation process.

  11. Hydrazino-methoxy-1,3,5-triazine Derivatives' Excellent Corrosion Organic Inhibitors of Steel in Acidic Chloride Solution.

    Science.gov (United States)

    El-Faham, Ayman; Osman, Sameh M; Al-Lohedan, Hamad A; El-Mahdy, Gamal A

    2016-06-01

    The corrosion inhibition performance of 2-hydrazino-4,6-dimethoxy-1,3,5-tirazine (DMeHT), 2,4-dihydrazino-6-methoxy-1,3,5-triaizine (DHMeT), and 2,4,6-tridydrazino-1,3,5-triaizne (TH₃) on steel corrosion in acidic media was examined using electrochemical techniques. The results showed 2,4-Ddihydrazino-6-methoxy-1,3,5-triaizine (DHMeT) gave the best corrosion protection performance among the other hydrazino derivatives even at a low concentration of 25 ppm (95%). The number of hydrazino groups play an important role in the corrosion inhibition, where the two hydrazine groups increased the electrostatic interactions between the protonated tested compounds, the negatively charged steel surface resulted from the adsorption of the chloride anions, and the presence of the methoxy group made the compound more reliable for formation of film protection on the surface of steel through the lone pair of oxygen atoms. Electrochemical Impedance Spectroscopy (EIS) measurements suggested that the corrosion process of steel in presence of the hydrazino-s-triazine derivatives (TH₃, DMeHT and DHMeT) were being controlled by the charge transfer reaction. Polarization curves indicated that the examined TH₃, DMeHT and DHMeT behaved as mixed type inhibitors.

  12. Hydrazino-methoxy-1,3,5-triazine Derivatives’ Excellent Corrosion Organic Inhibitors of Steel in Acidic Chloride Solution

    Directory of Open Access Journals (Sweden)

    Ayman El-Faham

    2016-06-01

    Full Text Available The corrosion inhibition performance of 2-hydrazino-4,6-dimethoxy-1,3,5-tirazine (DMeHT, 2,4-dihydrazino-6-methoxy-1,3,5-triaizine (DHMeT, and 2,4,6-tridydrazino-1,3,5-triaizne (TH3 on steel corrosion in acidic media was examined using electrochemical techniques. The results showed 2,4-Ddihydrazino-6-methoxy-1,3,5-triaizine (DHMeT gave the best corrosion protection performance among the other hydrazino derivatives even at a low concentration of 25 ppm (95%. The number of hydrazino groups play an important role in the corrosion inhibition, where the two hydrazine groups increased the electrostatic interactions between the protonated tested compounds, the negatively charged steel surface resulted from the adsorption of the chloride anions, and the presence of the methoxy group made the compound more reliable for formation of film protection on the surface of steel through the lone pair of oxygen atoms. Electrochemical Impedance Spectroscopy (EIS measurements suggested that the corrosion process of steel in presence of the hydrazino-s-triazine derivatives (TH3, DMeHT and DHMeT were being controlled by the charge transfer reaction. Polarization curves indicated that the examined TH3, DMeHT and DHMeT behaved as mixed type inhibitors.

  13. Influence of heat treatment on microstructure and passivity of Cu–30Zn–1Sn alloy in buffer solution containing chloride ions

    Indian Academy of Sciences (India)

    U Tabrizi; R Parvizi; A Davoodi; M H Moayed

    2012-02-01

    Tin as an alloying element is of great interest in brasses for dezincification impediment. In this paper, Cu–30Zn–1Sn alloy was submitted to three different heat treatments, viz. A (heating up to 800 °C for 20 h, held at 200 °C for 20 h in salt bath and air cooled), B (heating up to 800 °C for 20 h and water quenched) and C (heating up to 600 °C for 20 h and water quenched). The influence of heat treatment on microstructure was evaluated by OM and SEM–EDS analysis. The corrosion resistance in buffer solution (pH 9), H3BO3/Na2B4O7.10H2O, with various concentrations of chloride ions was evaluated by potentiodynamic polarization curves and compared with multicomponent Pourbaix diagrams. A correlation between the heat treatment, microstructure and passivity of the heat treated samples was observed. The results indicated that all heat treatment procedures led to formation of , and -Sn-rich phases as microstructure constituents with a small fraction of ' phase in A. Sn-rich phase appears in grain boundaries and its morphology was slightly changed due to heat treatment. Beneficial influence of low concentration chloride ions on passivity was associated with the formation of copper oxides/hydroxide and chloride complexes. Deterioration was observed at concentrations higher than 0.05 M NaCl due to accelerated dissolution of copper by formation of CuCl$^{−}_{2}$. As a result of dezincification process, preferential corrosion attack and copper redeposition on phase (matrix) were observed. However, Sn-rich (1) phase in grain boundaries was not attacked due to SnO2 formation. In buffer solution, the higher passivity current density in A was related to the presence of small amount of ' phase. On the other hand, in 1 M NaCl, lower critical current density for passivation in B and A (about two times lower than C) was attributed to the grain size effect.

  14. Removal of copper (II) from aqueous solutions by flotation using polyaluminum chloride silicate (PAX-XL60 S) as coagulant and carbonate ion as activator.

    Science.gov (United States)

    Ghazy, S E; Mahmoud, I A; Ragab, A H

    2006-01-01

    Flotation is a separation technology for removing toxic heavy metal ions from aqueous solutions. Here a simple and rapid flotation procedure is presented for the removal of copper(II) from aqueous solutions. It is based on the use of polyaluminum chloride silicate (PAX-XL60 S) as coagulant and flocculent, carbonate ion as activator and oleic acid (HOL) as surfactant. Both ion and precipitate flotation are included depending on the solution pH. Ion and precipitate flotation in the aqueous HOL-PAX-XL60 S-Cu2+-CO3(2-) system gave powerful preferential removal of Cu2+ (F -100%) over the HOL-PAX-XL60 S-Cu2+ system containing no CO3(2+) ion (F approximately 86%). The role of CO3(2-) ion is also evident from decreasing the dose of PAX-XL60 S from 700 mg l(-1) to 200 mg l(-1). The other parameters, influencing the flotation process, namely: metal ion, surfactant and PAX-XL60 S concentrations, ionic strength, temperature and foreign ions were examined. Moreover, the procedure was successfully applied to recover Cu2+ ions from different volumes up to 11 and from natural water samples.

  15. Properties of Bessel Function Solution to Kepler's Equation with Application to Opposition and Conjunction of Earth-Mars

    Science.gov (United States)

    Ebaid, Abdelhalim; Al-Blowy, Ahmed B.

    2016-05-01

    In this article, a simple approach is suggested to calculate the approximate dates of opposition and conjunction of Earth and Mars since their opposition on August 28, 2003 (at perihelion of Mars). The goal of this article has been achieved via using accurate analytical solution to Kepler's equation in terms of Bessel function. The periodicity property of this solution and its particular values at specified times are discussed through some lemmas. The mathematical conditions of opposition and conjunction of the two planets are formulated. Moreover, the intervals of opposition and conjunction have been determined using the graphs of some defined functions. The calculations reveal that there are nine possible oppositions and conjunctions for Earth and Mars during 20 years started on August 28, 2003. The dates of such oppositions and conjunctions were approximately determined and listed in Tables. It is found that our calculations differ few days from the published real dates of Earth-Mars oppositions due to the neglected effects of the gravitational attraction of other planets in the Solar system on the motion of two planets. The period of 20 years can be extended for any number of years by following the suggested analysis. Furthermore, the current approach may be extended to study the opposition and conjunction of the Earth and any outer planet.

  16. Solitary, explosive, rational and elliptic doubly periodic solutions for nonlinear electron-acoustic waves in the earth's magnetotail region

    CERN Document Server

    El-Wakil, S A; El-Shewy, E K; Abd-El-Hamid, H M

    2010-01-01

    A theoretical investigation has been made of electron acoustic wave propagating in unmagnetized collisionless plasma consisting of a cold electron fluid and isothermal ions with two different temperatures obeying Boltzmann type distributions. Based on the pseudo-potential approach, large amplitude potential structures and the existence of Solitary waves are discussed. The reductive perturbation method has been employed to derive the Korteweg-de Vries (KdV) equation for small but finite amplitude electrostatic waves. An algebraic method with computerized symbolic computation, which greatly exceeds the applicability of the existing tanh, extended tanh methods in obtaining a series of exact solutions of the KdV equation, is used here. Numerical studies have been made using plasma parameters close to those values corresponding to Earth's plasma sheet boundary layer region reveals different solutions i.e., bell-shaped solitary pulses and singularity solutions at a finite point which called "blowup" solutions, Jaco...

  17. Coexistence of iso-nonergodic laponite gel and glass in 1-methyl-3-octylimidazolium chloride ionic liquid solutions.

    Science.gov (United States)

    Joshi, Nidhi; Rawat, Kamla; Bohidar, H B

    2014-06-12

    We report unique colloidal gel-glass coexistence in aqueous laponite dispersion (2% w/v) in the presence of 1-methyl-3-octylimidazolium chloride ionic liquid (IL, [C8mim][Cl], concentration 0.01 to 0.05% w/v), where both of the phases had identical nonergodicity and were dynamically interactive. With aging, the nascent heterogeneous dispersion exhibited spontaneous two-phase separation, and the time-dependent relative viscosity followed: η(r) = |ε|(-k) where ε = (t - t(g))/t(g) and t(g) is the time required for the system to get arrested, with k decreasing from 3.13 to 2.54 as the IL concentration was increased from 0 to 0.03% (w/v), implying slowing down of the arrest kinetics. This time was measured from viscosity and rheology studies, revealing the formation of IL-mediated finite size colloidal networks on a time scale of ~4 × 10(3) s, whereas the dispersion developed a large viscosity one decade in time later (~4 × 10(4) s). Homogeneous transparent upper phase was an entropic glass and exhibited substantial storage modulus gain (300-3000 Pa) with an increase in IL concentration (0 to 0.05% (w/v)). The translucent lower gel phase had a much higher storage modulus. Dynamic light scattering measured bimodal relaxation time of concentration fluctuations. The degree of nonergodicity in the two phases was approximately the same, implying laponite-IL cluster exchange across the interface (identical slow-mode diffusivity). In summary, IL-induced first-order phase separation in laponite dispersion produced a homogeneous colloidal gel coexisting with a glass not commonly observed in soft matter systems. This implied that the two phases were dynamically coupled on long time scales, whereas their short-time behavior was distinctively different.

  18. The analysis of crystallization of sodium chloride from the solution in vacuum crystallizer with the recirculation of the suspension

    Directory of Open Access Journals (Sweden)

    Jotanović Milovan B.

    2009-01-01

    Full Text Available Crystallization from a solution most often is the final stage of many technological processes, and has a major role in bulk chemical industry. Basic requirements which stand before the process of crystallization are as follows: providing a minimum energy use-up together with a maximum specific capacity of the crystallizer, as well as with obtaining a product with the necessary degree of purity. These demands are successfully fulfilled by vacuum crystallizers with recirculation of suspension, which are the most promising apparatus for the crystallization of inorganic salts from solutions in bulk production. Vacuum crystallizers, like other chemical apparatuses, are described as a sum of physical and chemical phenomena which together create a unit process of crystallization of NaCl from water solutions. The term apparatus process unit (APU was introduced and a vacuum crystallizer is described as the sum of APU and shown in a structural scheme. The analysis of the vacuum crystallizer was performed based on its APU component, using theoretical assumptions, the results published as well as the results of researches on models. A particular focus was given to the description of the mass and heat transfer, as well as to the hydrodynamics of fluids in the area where the starting solution and the recircular suspension are mixed, in the circulation channel and the central pipe, as well as in the area of vaporization. This study gives the conclusions made based on the investigation of vacuum crystallizers. .

  19. Study of caffeine as corrosion inhibitors of carbon steel in chloride solution containing hydrogen sulfide using electrochemical impedance spectroscopy (EIS)

    Science.gov (United States)

    Solehudin, Agus; Berman, Ega Taqwali; Nurdin, Isdiriayani

    2015-09-01

    The corrosion behaviour of steel surface in the absence and presence of caffeine in 3.5% NaCl solution containing dissolved H2S gas is studied using electrochemical impedance spectroscopy (EIS). The experimental results of carbon steel corrosion in 3.5% NaCl solution containing 500 mg/l H2S at different caffeine concentrations showed that corrosion rate of carbon steel decreases with increasing of caffeine concentrations from 0 to 0,1 mmol/l. Whereas, the corrosion rate increase with increasing of caffeine concentrations from 1 to 10 mmol/l. It is clear that no inhibition efficiency increases with increasing inhibitor concentration. The optimum value of inhibition efficiency was 90% at a caffeine concentration of 0.1 mmol/l. This suggests that caffeine's performance as a corrosion inhibitor is more effective at a concentration of 0.1 mmol/l.

  20. Inhibition of copper corrosion in sodium chloride solution by the self-assembled monolayer of sodium diethyldithiocarbamate

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Q.Q., E-mail: liaoqq1971@yahoo.com.c [Key Lab of Shanghai Colleges and Universities for Electric Power Corrosion Control and Applied Electrochemistry, Shanghai Engineering Research Center of Energy - Saving in Heat Exchange Systems, Shanghai University of Electric Power, Shanghai 200090 (China); Yue, Z.W.; Yang, D. [Key Lab of Shanghai Colleges and Universities for Electric Power Corrosion Control and Applied Electrochemistry, Shanghai Engineering Research Center of Energy - Saving in Heat Exchange Systems, Shanghai University of Electric Power, Shanghai 200090 (China); Wang, Z.H. [Department of Chemistry, Tongji University, Shanghai 200092 (China); Li, Z.H. [Department of Chemistry, Fudan University, Shanghai 200433 (China); Ge, H.H. [Key Lab of Shanghai Colleges and Universities for Electric Power Corrosion Control and Applied Electrochemistry, Shanghai Engineering Research Center of Energy - Saving in Heat Exchange Systems, Shanghai University of Electric Power, Shanghai 200090 (China); Li, Y.J. [Department of Chemistry, Tongji University, Shanghai 200092 (China)

    2011-05-15

    Research highlights: DDTC is of low toxicity. DDTC SAM had good corrosion inhibition effects on copper in 3% NaCl solution. DDTC SAM was chemisorbed on copper surface by its S atoms. - Abstract: Sodium diethyldithiocarbamate (DDTC) self-assembled monolayer (SAM) on copper surface has been investigated by SERS and EDS and the results show that DDTC SAM is chemisorbed on copper surface by its S atoms with tilted orientation. Corrosion inhibition ability of DDTC SAM was measured in 3% NaCl solution using electrochemical methods. The impedance results indicate that the maximum inhibition efficiency of DDTC SAM can reach 99%. Quantum chemical calculations show that DDTC has relatively small {Delta}E between HOMO and LUMO and large negative charge in its two sulfur atoms, which facilitates the formation of a DDTC SAM on copper surface.

  1. Electrochemical and Spectroscopic Study of Benzotriazole Films Formed on Copper, Copper-zinc Alloys and Zinc in Chloride Solution

    OpenAIRE

    Milošev, I.; Kosec, T.

    2009-01-01

    The formation of protective layers on copper, zinc and copper-zinc (Cu-10Zn and Cu-40Zn) alloys at open circuit potential in aerated, near neutral 0.5 M NaCl solution containing benzotriazole (BTA) was studied using potentiodynamic measurements, electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS). The addition of benzotriazole affects the dissolution of the materials investigated. Benzotriazole, generally known as an inhibitor of copper corrosion, is als...

  2. Effect of the cation model on the equilibrium structure of poly-L-glutamate in aqueous sodium chloride solution

    Science.gov (United States)

    Marchand, Gabriel; Soetens, Jean-Christophe; Jacquemin, Denis; Bopp, Philippe A.

    2015-12-01

    We demonstrate that different sets of Lennard-Jones parameters proposed for the Na+ ion, in conjunction with the empirical combining rules routinely used in simulation packages, can lead to essentially different equilibrium structures for a deprotonated poly-L-glutamic acid molecule (poly-L-glutamate) dissolved in a 0.3M aqueous NaCl solution. It is, however, difficult to discriminate a priori between these model potentials; when investigating the structure of the Na+-solvation shell in bulk NaCl solution, all parameter sets lead to radial distribution functions and solvation numbers in broad agreement with the available experimental data. We do not find any such dependency of the equilibrium structure on the parameters associated with the Cl- ion. This work does not aim at recommending a particular set of parameters for any particular purpose. Instead, it stresses the model dependence of simulation results for complex systems such as biomolecules in solution and thus the difficulties if simulations are to be used for unbiased predictions, or to discriminate between contradictory experiments. However, this opens the possibility of validating a model specifically in view of analyzing experimental data believed to be reliable.

  3. Diffusion coefficients of nickel chloride in aqueous solutions of lactose at T = 298.15 K and T = 310.15 K

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Ana C.F., E-mail: anacfrib@ci.uc.p [Department of Chemistry, University of Coimbra, 3004-535 Coimbra (Portugal); Gomes, Joselaine C.S., E-mail: leidygomes18@hotmail.co [Department of Chemistry, University of Coimbra, 3004-535 Coimbra (Portugal); Barros, Marisa C.F., E-mail: marisa.barros@gmail.co [Department of Chemistry, University of Coimbra, 3004-535 Coimbra (Portugal); Lobo, Victor M.M., E-mail: vlobo@ci.uc.p [Department of Chemistry, University of Coimbra, 3004-535 Coimbra (Portugal); Esteso, Miguel A., E-mail: miguel.esteso@uah.e [Departamento de Quimica Fisica, Facultad de Farmacia, Universidad de Alcala, 28871, Alcala de Henares (Madrid) (Spain)

    2011-03-15

    Binary mutual diffusion coefficients (interdiffusion coefficients) of nickel chloride in water at T = 298.15 K and T = 310.15 K, and at concentrations between (0.000 and 0.100) mol {center_dot} dm{sup -3}, using a Taylor dispersion method have been measured. These data are discussed on the basis of the Onsager-Fuoss and Pikal models. The equivalent conductance at infinitesimal concentration of the nickel ion in these solutions at T = 310.15 K has been estimated using these results. Through the same technique, ternary mutual diffusion coefficients (D{sub 11}, D{sub 22}, D{sub 12}, and D{sub 21}) for aqueous solutions containing NiCl{sub 2} and lactose, at T = 298.15 K and T = 310.15 K, and at different carrier concentrations were also measured. These data permit us to have a better understanding of the structure of these systems and the thermodynamic behaviour of NiCl{sub 2} in different media.

  4. Surface-enhanced Raman scattering and atomic force microscopy of brass electrodes in sulfuric acid solution containing benzotriazole and chloride ion

    Energy Technology Data Exchange (ETDEWEB)

    Rubim, J.C.; Kim, J.; Henderson, E.; Cotton, T.M. (Instituto de Quimica da Universidade de Sao Paulo (Brazil) Ames Lab., IA (United States) Iowa State Univ., Ames (United States))

    1993-01-01

    Three different methods were used to roughen brass (Cu/Zn = 67/33) electrodes in 0.5 M H[sub 2]SO[sub 4] containing 1.0 mM benzotriazole (BTAH): (1) polarization at +0.05 V vs. saturated calomel for 5 min; (2) immersion in the above solution for six hours; and (3) oxidation-reduction cycling in the presence of chloride ion. The surfaces prepared by the first two methods exhibited surface-enhanced Raman scattering (SERS) spectra of the polymeric complex [Cu(I)BTA][sub s]. The SERS spectrum obtained from electrodes prepared by the third method is very similar to that of [Cu(I)CIBTAH][sub 4]. Examination of the electrodes by atomic force microscopy (AFM) showed that a large number of grain boundary sites are formed by the roughening processes. This effect is attributed to the loss of zinc, which occurs during corrosion of the mirror-like, polished brass electrode surface in the sulfuric acid solution. 11 refs., 5 figs.

  5. 源溶液成分对氯离子在混凝土中电迁移特性的影响%Research on Influence of Source Solution on Chloride Migration in Concrete

    Institute of Scientific and Technical Information of China (English)

    宋子健; 蒋林华; 衡由索; 濮琦; 朱乔

    2011-01-01

    氯离子在混凝土中的电迁移过程受离子间相互作用、双电层效应等因素的影响,扩散系数并非常量,而是溶液成分的函数.详细阐述了溶液成分影响氯离子在混凝土中扩散迁移特性的机理,并通过改进的RCM法测定了不同水灰比、龄期、外加电压和源溶液成分下的氯离子扩散系数.实验结果表明,较其它因素而言源溶液成分对电迁移特性影响较小,但总体仍呈一定规律.%Chloride diffusivity tested by migration method is not a constant but a function of solution composition due to the effect of ionic interaction, electrical double slayer, etc. The complicated influencing mechanism of solution composition on chloride diffusivity in concrete was introduced, chloride diffusion coefficients were tested by modified RCM method under different conditions of ω/c ratio, age, external voltage and source solution. An analysis of test result is presented that the influence of source solution on chloride migration follows a certain discipline although it is less obvious than other factors.

  6. Effects of hypertonic sodium chloride solution on the electrophysiologic alterations caused by bupivacaine in the dog heart

    Directory of Open Access Journals (Sweden)

    Scalabrini A.

    2003-01-01

    Full Text Available The effects of various hypertonic solutions on the intraventricular conduction, ventricular repolarization and the arrhythmias caused by the intravenous (iv injection of bupivacaine (6.5 mg/kg were studied in sodium pentobarbital-anesthetized mongrel dogs. Hypertonic solutions, given iv 5 min before bupivacaine, were 7.5% (w/v NaCl, 5.4% (w/v LiCl, 50% (w/v glucose (2,400 mOsm/l, 5 ml/kg, or 20% (w/v mannitol (1,200 mOsm/l, 10 ml/kg. Bupivacaine induced severe arrhythmias and ventricular conduction and repolarization disturbances, as reflected by significant increases in QRS complex duration, HV interval, IV interval and monophasic action potential duration, as well as severe hemodynamic impairment. Significant prevention against ventricular electrophysiologic and hemodynamic disturbances and ventricular arrhythmias was observed with 7.5% NaCl (percent increase in QRS complex duration: 164.4 ± 21.8% in the non-pretreated group vs 74.7 ± 14.1% in the pretreated group, P<0.05; percent increase in HV interval: 131.4 ± 16.1% in the non-pretreated group vs 58.2 ± 7.5% in the pretreated group, P<0.05; percent increase in monophasic action potential duration: 22.7 ± 6.8% in the non-pretreated group vs 9.8 ± 6.3% in the pretreated group, P<0.05; percent decrease in cardiac index: -46 ± 6% in the non-pretreated group vs -28 ± 5% in the pretreated group, P<0.05. The other three hypertonic solutions were ineffective. These findings suggest an involvement of sodium ions in the mechanism of hypertonic protection.

  7. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    and time, and where both the surface chloride concentration and the diffusion coefficient are allowed to vary in time; the Mejlbro-Poulsen model is the general solution to Fick’s 2nd law. The paper also presents conversion formulas for the four decisive but rather abstract parameters to parameters, which...

  8. Corrosion Properties in Sodium Chloride Solutions of Al–TiC Composites in situ Synthesized by HFIHF

    Directory of Open Access Journals (Sweden)

    El-Sayed M. Sherif

    2015-10-01

    Full Text Available Al–TiC nanocomposite materials have been prepared by a new in situ synthesizing technique. A mixture of aluminum, titanium, and graphite has been prepared using ball milling technique and then melted in a high frequency induction heat furnace (HFIHF at different sintering temperatures, namely 900, 1100, and 1300 °C. The effect of sintering temperature on the corrosion of the Al–TiC composite in 3.5% NaCl solutions was investigated using cyclic potentiodynamic polarization, chronoamperometric current-time, open-circuit potential, and electrochemical impedance spectroscopy measurements. The surface of the composites after their corrosion in the test solution was investigated using scanning electron microscopy and energy dispersive X-ray analyses. It has been found that all manufactured composites suffer uniform corrosion. All corrosion test techniques were consistent with each other and confirmed clearly that the corrosion resistance of Al composites increased according to their sintering temperature in the following order 900 > 1100 > 1300 °C.

  9. Effect of sodium chloride on solute-solvent interactions in aqueous polyethylene glycol-sodium sulfate two-phase systems.

    Science.gov (United States)

    da Silva, Nuno R; Ferreira, Luisa A; Madeira, Pedro P; Teixeira, José A; Uversky, Vladimir N; Zaslavsky, Boris Y

    2015-12-18

    Partition behavior of eight small organic compounds and six proteins was examined in poly(ethylene glycol)-8000-sodium sulfate aqueous two-phase systems containing 0.215M NaCl and 0.5M osmolyte (sorbitol, sucrose, TMAO) and poly(ethylene glycol)-10000-sodium sulfate-0.215M NaCl system, all in 0.01M sodium phosphate buffer, pH 6.8. The differences between the solvent properties of the coexisting phases (solvent dipolarity/polarizability, hydrogen bond donor acidity, and hydrogen bond acceptor basicity) were characterized with solvatochromic dyes using the solvatochromic comparison method. Differences between the electrostatic properties of the phases were determined by analysis of partitioning of sodium salts of dinitrophenylated (DNP-) amino acids with aliphatic alkyl side-chain. The partition coefficients of all compounds examined (including proteins) were described in terms of solute-solvent interactions. The results obtained in the study show that solute-solvent interactions of nonionic organic compounds and proteins in polyethylene glycol-sodium sulfate aqueous two-phase system change in the presence of NaCl additive.

  10. Spherical harmonic series solution of fields excited by vertical electric dipole in earth-ionosphere cavity

    Institute of Scientific and Technical Information of China (English)

    Yuanxin WANG; Wensheng FAN; Weiyan PAN; Hongqi ZHANG

    2008-01-01

    The spherical harmonic series expression of electromagnetic fields excited by ELF/SLF vertical electric dipole in the spherical earth-ionosphere cavity is derived when the earth and ionosphere are regarded as non-ideal conductors. A method of speeding numerical convergence has been presented. The electromagnetic fields in the cavity are calculated by this algorithm, and the results show that the electromagnetic fields between the earth and the ionosphere are the sum of two traveling waves in the SLF band. Moreover, the results are in complete agreement with that of the well-known spherical second-order approximation in the SLF band. The electromagnetic fields in the cavity are a type of standing wave in the ELF band and the variation of the amplitude versus frequency coincides with Schumann's resonance.

  11. Electrokinetic effect of the Loma Prieta earthquake calculated by an entire-Earth FDTD solution of Maxwell's equations

    Science.gov (United States)

    Simpson, Jamesina J.; Taflove, Allen

    2005-05-01

    We report what we believe to be the first three-dimensional computational solution of the full-vector Maxwell's equations for hypothesized pre-seismic electromagnetic phenomena propagated within the entire Earth-ionosphere cavity. Periodic boundary conditions are used in conjunction with a variable-cell finite-difference time-domain (FDTD) space lattice wrapping around the complete Earth-sphere and extending +/-100 km radially from sea level. This technique permits a direct time-domain calculation of round-the-world ULF/ELF propagation accounting for arbitrary horizontal as well as vertical geometrical and electrical inhomogeneities/anisotropies of the excitation, ionosphere, lithosphere, and oceans. In this study, we model electrokinetic currents at depths of 2.5 km and 17 km near the hypocenter of the Loma Prieta earthquake and compare the FDTD-calculated surface magnetic field to analytical results and measurements previously reported in the literature. We accommodate the complete physics introduced by impulsive electromagnetic wave propagation through the conductive Earth, and hence illustrate the importance of solving the full Maxwell's equations when modeling current sources within the Earth's crust. Our calculated spectra agree qualitatively with those reported by Fraser-Smith et al. (1990).

  12. Cytotoxicity of five fluoroquinolone and two nonsteroidal anti-inflammatory benzalkonium chloride-free ophthalmic solutions in four corneoconjunctival cell lines

    Directory of Open Access Journals (Sweden)

    Masahiko Ayaki

    2010-09-01

    Full Text Available Masahiko Ayaki1, Atsuo Iwasawa2, Mitsutaka Soda3, Shigeo Yaguchi3, Ryohei Koide41Department of Ophthalmology, Saitama National Hospital, Saitama, Japan; 2Department of Clinical Pathology, Showa University Fujigaoka Hospital, Yokohama, Japan; 3Department of Ophthalmology, Showa University Fujigaoka Rehabilitation Hospital, Yokohama, Japan; 4Department of Ophthalmology, Showa University School of Medicine, Tokyo, JapanPurpose: Epithelial disorders after eye surgery can result in visual deterioration and patient discomfort. Such disorders may be caused by drug toxicity. In the present study, we evaluated the toxicity of ophthalmic solutions, with or without benzalkonium chloride (BAK as the preservative, used for postoperative care.Methods: A range of commercially available antibiotic and anti-inflammatory ophthalmic solutions used postoperatively (ie, levofloxacin, moxifloxacin, gatifloxacin, norfloxacin, tosufloxacin, dibekacin, cefmenoxime, diclofenac, bromfenac, pranoprofen, betamethasone, and fluoromethorone were assessed in three corneal cell lines and one conjunctival cell line. All antibiotic solutions were BAK free. Cell viability was determined with the 3-(4,5-dimethyl-2 thiazoyl-2,5-diphenyl-2H-tetrazolium bromide (MTT assay after cells had been exposed to the drugs for 48 h. The effects of preservatives on cell viability were also determined. Toxicity was compared using the cell viability score (CVS.Results: Based on results of the MTT assay and CVS, the order of cell viability after exposure to the antibiotic solutions was cefmenoxime ≥ tosufloxicin ≥ dibekacin ≥ levofloxacin ≥ norfloxacin = gatifloxacin = moxifloxacin. For the anti-inflammatory solutions, the order of cell viability was betamethasone ≥ betamethasone + fradiomycin > preservative-free diclofenac ≥ preservative-free bromfenac >> 0.02% fluoromethorone ≥ 0.1% fluoromethorone = diclofenac + preservative = bromfenac + preservative = pranoprofen. The anti

  13. Durability of API class B cement pastes exposed to aqueous solutions containing chloride, sulphate and magnesium ions

    Directory of Open Access Journals (Sweden)

    Hernández, M. E.

    2008-12-01

    Full Text Available This paper discusses a durability study conducted on API class B cement, the type used in shallow oil wells, when exposed to aggressive formation water. Its resistance to the major ions, namely –SO4=, Mg+2 and Cl-–, is related both to its capacity to assimilate the aggressive action of each harmful agent and to the changes in the chemical reactivity of some of its components. The methodology used consisted in preparing and immersing cement specimens in neutral solutions containing variable concentrations of these ions to monitor the chemical reactions taking place. These solutions were analyzed and XRD studies were conducted for over a year to identify mineralogical variations. The purposes of the study were to determine the effects of joint ionic attack on this kind of cement and to monitor the variations in the calcium concentration in the aqueous solutions of Na2SO4, MgCl2 and NaCl in contact with API class B cement pastesEste trabajo se basa en el estudio de la durabilidad de un cemento API clase B, utilizado en pozos petrolíferos someros, frente a la agresividad de las aguas de formación a las que puede estar expuesto. Su eficacia frente a la exposición a los iones más importantes –SO4=, Mg+2 y Cl-– se relaciona con su capacidad de asimilar la acción agresiva de cada agente perjudicial, así como de las reacciones químicas que sufra por la reactividad de alguno de sus compuestos. La metodología aplicada supone la preparación de probetas de este cemento y su inmersión en disoluciones neutras, conteniendo los referidos iones a distintas concentraciones, para evaluar el desarrollo de las reacciones existentes en su seno. A tal fin se realizaron análisis de las disoluciones y estudios de DRX durante más de un año para conocer su evolución mineralógica. El objetivo del trabajo ha sido determinar los efectos resultantes de los ataques conjuntos de los citados iones al referido cemento; así como la observación de las

  14. Occurrence of methane hydrate in saturated and unsaturated solutions of sodium chloride and water in dependence of temperature and pressure

    Energy Technology Data Exchange (ETDEWEB)

    de Roo, J.L.; Diepen, G.A.M.; Lichtenthaler, R.N.; Peters, C.J.

    1983-07-01

    Experimental results of the formation of methane hydrate in dependence of temperature and pressure in unsaturated solutions of NaCl in water will be presented in a temperature range from 261.85 to 285.98 K and pressure up to 11.0 MPa. Furthermore the four-phase equilibrium NaCl X 2H/sub 2/O /SUB s/ -CH/sub 4/ X nH/sub 2/O /SUB s/ -L-G has been calculated from the experimental results. Also the heats of transformation of several other equilibria in the ternary system CH/sub 4/-H/sub 2/O-NaCl are obtained.

  15. The uptake and transpiration of water and the accumulation of lead by plants growing on lead chloride solutions

    Directory of Open Access Journals (Sweden)

    Marek Burzyński

    2014-01-01

    Full Text Available The placement of approximately two week-old bean, cucumber and wheat plants in PbCl2 solutions caused significant decreases in transpiration and uptake of water. The amount of transpiration and water uptake depended on the PbCl2 concentration and length of treatment. Cucumber plants were the most sensitive to lead and accumu-lated the. greatest amounts of it. Beans were the least sensitive, although they accumulated more lead than wheat. The lead taken up by cucumbers and beans accumulated mainly in the roots while the distribution of lead in wheat was rather uniform in the roots and above-ground parts. The removal of roots from bean plants caused high accumulation of lead in the lower stem parts.

  16. Modeling and simulation of pit chemistry of 304 austenitic stainless steel under applied stress in sodium chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Yuhui, E-mail: yhhuang@ecust.edu.cn [Key Laboratory of Pressure Systems and Safety, MOE, School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237 (China); Tu, Shan-Tung; Xuan, Fu-Zhen [Key Laboratory of Pressure Systems and Safety, MOE, School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237 (China)

    2013-04-15

    Highlights: ► A corrosion model was developed to simulate a stressed metal surface with a pit. ► The stress state in the pit bottom was coupled with the local corrosion environment. ► An analytical expression was established for current density of deformed pit surface. ► Local deformation had a strong effect on potential and species concentration in pits. -- Abstract: A mathematical model for simulating the active dissolution of a pit on stressed metal surface had been developed. Based on active dissolution mechanism, dissolution current density on the pit surface was assumed and extended through accounting for the thermal activation energy and the multiaxial stress state in pit bottom. The influence of applied tensile stress, pit radius and temperature was addressed. The distribution of solution potential and species concentration was predicted for different applied tensile stresses based on finite element calculations.

  17. Determination of Pyridine in Cetylpyridinium Chloride Ophthalmic Solution%西吡氯铵滴眼液中吡啶的测定

    Institute of Scientific and Technical Information of China (English)

    赵霞; 李博; 徐光富; 步芬; 王岁楼

    2013-01-01

    Objective: To establish a gas chromatography method for the determination of pyridine in cetylpyridinium chloride ophthalmic solution. Methods: The separation was performed on a capillary column which was a copolymer of 5% diphenyl-95% diphenyl siloxane as stationary phase.Column temperature was 35℃for 5 minutes.Then it increased to 115℃in rate of 8℃per minute.Carrier gas was nitrogen. Injector and detector were set at 120℃and 260℃respectively. Results:Pyridine and contamination could be completely separated with the established method. It was a linear correlation between the peak area and the concentration in concentration range of 0.492~9.84μg/ml.The recovery was 99.8%(n=9).RSD is 4.9%(n=6). Conclusion: The established method was accurate, simple and is suitable for determination of pyridine in cetylpyridinium chloride ophthalmic solution.%目的:建立西吡氯铵滴眼液中吡啶的气相色谱测定法。方法:用5%二苯基-95%二甲基硅氧烷共聚物为固定相的毛细管柱(30m×0.54mm×5.0μm),柱温在35℃维持5分钟,然后以每分钟8℃的升温速率升至115℃,以氮气为载气,气化室和检测器温度分别为120℃和260℃。结果:吡啶与杂质峰之间的分离良好。在0.492~9.84μg/ml的范围内吡啶的峰面积和浓度线性相关,回收率99.8%(n=9),RSD为4.9%(n=6)。结论:该分析方法准确可靠,简便易行,可用于西吡氯铵滴眼液中吡啶的测定。

  18. Separating iterative solution model of generalized nonlinear dynamic least squares for data processing in building of digital earth

    Institute of Scientific and Technical Information of China (English)

    陶华学; 郭金运

    2003-01-01

    Data coming from different sources have different types and temporal states. Relations between one type of data and another ones, or between data and unknown parameters are almost nonlinear. It is not accurate and reliable to process the data in building the digital earth with the classical least squares method or the method of the common nonlinear least squares. So a generalized nonlinear dynamic least squares method was put forward to process data in building the digital earth. A separating solution model and the iterative calculation method were used to solve the generalized nonlinear dynamic least squares problem. In fact, a complex problem can be separated and then solved by converting to two sub-problems, each of which has a single variable. Therefore the dimension of unknown parameters can be reduced to its half, which simplifies the original high dimensional equations.

  19. Electrochemical evaluation of sodium metabisulfite as environmentally friendly inhibitor for corrosion of aluminum alloy 6061 in a chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Zaid, B., E-mail: zaidbachir@yahoo.com [Département de métallurgie, Division de Technologie du Combustible, Centre de Recherche Nucléaire de Draria CRND, BP. 43 Draria, Alger (Algeria); Maddache, N.; Saidi, D. [Département de métallurgie, Division de Technologie du Combustible, Centre de Recherche Nucléaire de Draria CRND, BP. 43 Draria, Alger (Algeria); Souami, N. [Centre de Recherche Nucléaire d’Alger CRNA, 2 Bd. Frantz Fanon, Alger (Algeria); Bacha, N. [Département de Mécanique, Université SAAD Dahleb, Blida (Algeria); Si Ahmed, A. [Im2np, UMR 7334 CNRS, Aix-Marseille Université, 13397 Marseille Cedex 20 (France)

    2015-04-25

    Highlights: • Sodium metabisulfite acts as cathodic-type inhibitor. • The polarization resistance increases with the inhibitor concentration. • The pit nucleation rate decreases with increasing inhibitor concentration. • The current rise linked to pit propagation drops as inhibitor content increases. • The reactions involved in the inhibition actions are pointed out. - Abstract: Inhibition properties of sodium metabisulfite (Na{sub 2}S{sub 2}O{sub 5}) on pitting corrosion of 6061 aluminum alloy, in 5 × 10{sup −2} M NaCl solution of pH near 7.2 at 298 K, are characterized using open circuit potential, polarization resistance, cyclic and chrono-amperometric polarization measurements. In addition, scanning electron microscopy coupled with energy dispersive spectroscopy and X-ray photoelectrons are employed. Sodium metabisulfite, which is well compatible with environmental requirements, seems to act as a cathodic-type corrosion inhibitor. The passivation range and the polarization resistance increase with Na{sub 2}S{sub 2}O{sub 5} concentration. The inhibition effects are also reflected through the substantial reduction of both the rate of pit nucleation and the current rise characterizing the pit propagation progress. The SEM–EDS and XPS analyses reveal the formation of a passive film, which contains sulfur atoms.

  20. Totally solution-processed CuInS2 solar cells based on chloride inks: reduced metastable phases and improved current density

    Science.gov (United States)

    Dehghani, Mehdi; Behjat, Abbas; Tajabadi, Fariba; Taghavinia, Nima

    2015-03-01

    Planar superstrate CuInS2 (CIS) solar cell devices are fabricated using totally solution-processed deposition methods. These Cd-free devices are structured by FTO/TiO2/In2S3/CIS/carbon, where TiO2 and In2S3 are deposited by spray pyrolysis, and a CIS film is deposited using spin-coating followed by annealing at 250 °C. The pasted carbon layer is utilized as the anode. No further sulfurization or selenization is employed. The Cu/In ratio in the ink is found as a critical factor affecting the morphology and crystallinity of the film as well as the photovoltaic performance of the device. An optimum Cu/In = 1.05 results in large-grain films with sharp diffraction peaks and, subsequently, optimal series resistance and shunt conductance. It is also found that the chloride-based ink results in CIS films with considerably reduced metastable phases, compared to the conventional acetate-based inks. A current density of 23.6 mA cm-2 is obtained for the best devices, leading to a conversion efficiency of 4.1%.

  1. Hydrolysis of insoluble cellulose to glucose catalyzed by cellulase-containing liposomes in an aqueous solution of 1-butyl-3-methylimidazolium chloride.

    Science.gov (United States)

    Yoshimoto, Makoto; Tanimura, Kazuhiko; Tokunaga, Kazuki; Kamimura, Akio

    2013-01-01

    The liposome containing cellulase from Trichoderma viride was prepared under the condition that an appreciable amount of cellulase was incorporated in lipid membranes. The liposomal cellulase and free enzyme were examined in their hydrolytic activities to insoluble cellulose powder CC31 in the acetate buffer solution (pH 4.8) of 15 w/w% [Bmim][Cl] (1-butyl-3-methylimidazolium chloride). The mean diameter and size distribution of cellulase-containing liposome were practically unchanged under the above condition. The free cellulase was deactivated more rapidly than the liposomal cellulase in catalyzing the hydrolysis of 2.0 g/l CC31 at 45°C in the presence of [Bmim][Cl] for 48 h. The activities of liposomal and free cellulase to cellobiose as soluble substrate were less susceptible to [Bmim][Cl] than their cellulolytic activities to CC31, meaning that β-glucosidase is relatively stable among the three enzyme components of cellulase. The rate of glucose production could be appreciably improved by the pretreatment of CC31 with [Bmim][Cl] alone at 120°C for 30 min followed by the liposomal cellulase-catalyzed hydrolysis of the substrate at 45°C at the [Bmim][Cl] concentration of 15 w/w%. © 2013 American Institute of Chemical Engineers.

  2. Hydration structure in concentrated aqueous lithium chloride solutions: A reverse Monte Carlo based combination of molecular dynamics simulations and diffraction data

    Science.gov (United States)

    Harsányi, I.; Pusztai, L.

    2012-11-01

    We report on a comparison of three interaction potential models of water (SPC/E, TIP4P-2005, and SWM4-DP) for describing the structure of concentrated aqueous lithium chloride solutions. Classical molecular dynamics simulations have been carried out and total scattering structure factors, calculated from the particle configurations, were compared with experimental diffraction data. Later, reverse Monte Carlo structural modelling was applied for refining molecular dynamics results, so that particle configurations consistent with neutron and X-ray diffraction data could be prepared that, at the same time, were as close as possible to the final stage of the molecular dynamics simulations. Partial radial distribution functions, first neighbors, and angular correlations were analysed further from the best fitting particle configurations. It was found that none of the water potential models describe the structure perfectly; overall, the SWM4-DP model seems to be the most promising. At the highest concentrations the SPC/E model appears to provide the best approximation of the water structure, whereas the TIP4P-2005 model proved to be the most successful for estimating the lithium-oxygen partial radial distribution function at each concentration.

  3. Fabrication and icing property of superhydrophilic and superhydrophobic aluminum surfaces derived from anodizing aluminum foil in a sodium chloride aqueous solution

    Science.gov (United States)

    Song, Meirong; Liu, Yuru; Cui, Shumin; Liu, Long; Yang, Min

    2013-10-01

    An aluminum foil with a rough surface was first prepared by anodic treatment in a neutral aqueous solution with the help of pitting corrosion of chlorides. First, the hydrophobic Al surface (contact angle around 79°) became superhydrophilic (contact angle smaller than 5°) after the anodizing process. Secondly, the superhydrophilic Al surface became superhydrophobic (contact angle larger than 150°) after being modified by oleic acid. Finally, the icing property of superhydrophilic, untreated, and superhydrophobic Al foils were investigated in a refrigerated cabinet at -12 °C. The mean total times to freeze a water droplet (6 μL) on the three foils were 17 s, 158 s and 1604 s, respectively. Thus, the superhydrophilic surface accelerates the icing process, while the superhydrophobic surface delays the process. The main reason for this transition might mainly result from the difference of the contact area of the water droplet with Al substrate: the increase in contact area with Al substrate will accelerate the heat conduct process, as well as the icing process; the decrease in contact area with Al substrate will delay the heat conduct process, as well as the icing process. Compared to the untreated Al foil, the contact area of the water droplet with the Al substrate was higher on superhydrophilic surface and smaller on the superhydrophobic surface, which led to the difference of the heat transfer time as well as the icing time.

  4. Corrosion Resistance ofAA6063-TypeAl-Mg-SiAlloy by Silicon Carbide in Sodium Chloride Solution for MarineApplication

    Institute of Scientific and Technical Information of China (English)

    Ojo Sunday Isaac Fayomi; Malik Abdulwahab; Ferdinand Asuke

    2015-01-01

    The present work focused on corrosion inhibition of AA6063 type Al-Mg-Si alloy in sodium chloride (NaCl) solution with a silicon carbide inhibitor, using the potentiodynamic electrochemical method. The aluminium alloy surface morphology was examined, in the as-received and as-corroded in the un-inhibited state, with scanning electron microscopy equipped with energy dispersive spectroscopy (SEM-EDS). The results obtained via linear polarization indicated a high corrosion potential for the unprotected as-received alloy. Equally, inhibition efficiency as high as 98.82% at 10.0 g/v silicon carbide addition was obtained with increased polarization resistance (Rp), while the current density reduced significantly for inhibited samples compared to the un-inhibited aluminium alloy. The adsorption mechanism of the inhibitor aluminium alloy follows the Langmuir adsorption isotherm. This shows that the corrosion rate of aluminium alloy with silicon carbide in NaCl environment decreased significantly with addition of the inhibitor.

  5. Extraction Equilibrium of Mn2+, Ca2+, and Mg2+ from Chloride Solutions by Di(2-ethylhexyl)phosphoric Acid Dissolved in Kerosene

    Science.gov (United States)

    Zhang, Chuanfu; Cao, Wenxin; Zhan, Jing; Ding, Fenghua; Hwang, Jiann-Yang

    2015-05-01

    The presence of calcium and magnesium affects the purity of the final product MnCl2 in hydrometallurgical treatment processes. The solvent extraction method can be used to separate Ca2+ and Mg2+ from Mn2+ solutions containing impurity ions such as Ca2+ and Mg2+. This article aims to investigate the single-stage extraction equilibrium of Ca2+, Mg2+, and Mn2+ in chloride medium using di(2-ethylhexyl)phosphoric acid in kerosene (O:A = 1:1). The results show that the pH0.5 values are 1.11, 1.56, and 2.18 for Ca2+, Mn2+, and Mg2+, respectively. The mechanism of extraction and stoichiometries of metal-containing extracted species were illustrated based on a slope analysis. The composition of the extracted species in the organic phase is proposed to be MnR2·R2H2, CaR2·R2H2, and MgR2·(R2H2)2, respectively.

  6. Solution Growth and Characterization of Single Crystals on Earth and in Microgravity

    Science.gov (United States)

    Aggarwal, M. D.; Currie, J. R.; Penn, B. G.; Batra, A. K.; Lal, R. B.

    2007-01-01

    Crystal growth has been of interest to physicists and engineers for a long time because of their unique properties. Single crystals are utilized in such diverse applications as pharmaceuticals, computers, infrared detectors, frequency measurements, piezoelectric devices, a variety of high-technology devices, and sensors. Solution crystal growth is one of the important techniques to grow a variety of crystals when the material decomposes at the melting point and a suitable solvent is available to make a saturated solution at a desired temperature. In this Technical Memorandum (TM) an attempt is made to give the fundamentals of growing crystals from solution including improved designs of various crystallizers. Since the same solution crystal growth technique could not be used in microgravity, the authors proposed a new cooled-sting technique to grow crystals in space. The authors experience from conducting two Space Shuttle solution crystal growth experiments are also detailed in this TM and the complexity of solution growth experiments to grow crystals in space are also discussed. These happen to be some of the early experiments performed in space, and various lessons learned are described. A brief discussion of protein crystal growth that shares basic principles of the solution growth technique is given, along with some flight hardware information for growth in microgravity.

  7. Antibacterial activity of silver nanoparticles obtained by pulsed laser ablation in pure water and in chloride solution

    Directory of Open Access Journals (Sweden)

    Brunella Perito

    2016-03-01

    Full Text Available Silver nanoparticles (AgNPs have increasingly gained importance as antibacterial agents with applications in several fields due to their strong, broad-range antimicrobial properties. AgNP synthesis by pulsed laser ablation in liquid (PLAL permits the preparation of stable Ag colloids in pure solvents without capping or stabilizing agents, producing AgNPs more suitable for biomedical applications than those prepared with common, wet chemical preparation techniques. To date, only a few investigations into the antimicrobial effect of AgNPs produced by PLAL have been performed. These have mainly been performed by ablation in water with nanosecond pulse widths. We previously observed a strong surface-enhanced Raman scattering (SERS signal from such AgNPs by “activating” the NP surface by the addition of a small quantity of LiCl to the colloid. Such surface effects could also influence the antimicrobial activity of the NPs. Their activity, on the other hand, could also be affected by other parameters linked to the ablation conditions, such as the pulse width. The antibacterial activity of AgNPs was evaluated for NPs obtained either by nanosecond (ns or picosecond (ps PLAL using a 1064 nm ablation wavelength, in pure water or in LiCl aqueous solution, with Escherichia coli and Bacillus subtilis as references for Gram-negative and Gram-positive bacteria, respectively. In all cases, AgNPs with an average diameter less than 10 nm were obtained, which has been shown in previous works to be the most effective size for bactericidal activity. The measured zeta-potential values were very negative, indicating excellent long-term colloidal stability. Antibacterial activity was observed against both microorganisms for the four AgNP formulations, but the ps-ablated nanoparticles were shown to more effectively inhibit the growth of both microorganisms. Moreover, LiCl modified AgNPs were the most effective, showing minimum inhibitory concentration (MIC values in

  8. Influence of the anions on the N-cationic benzethonium salts in the solid state and solution: Chloride, bromide, hydroxide and citrate hydrates

    Energy Technology Data Exchange (ETDEWEB)

    Paradies, Henrich H., E-mail: hparadies@aol.com, E-mail: hparadies@jacobs-university.de [The University of Salford, Joule Physics Laboratory, Faculty of Science, Engineering and Environment, Manchester M5 4 WT (United Kingdom); Jacobs University Bremen, Life Sciences and Chemistry Department, Campus Ring 1, D-28759 Bremen (Germany); Reichelt, Hendrik [The University of Salford, Joule Physics Laboratory, Faculty of Science, Engineering and Environment, Manchester M5 4 WT (United Kingdom)

    2016-06-15

    The crystal structures of the hydrated cationic surfactant benzethonium (Bzth) chloride, bromide, hydroxide, and citrate have been determined by X-ray diffraction analysis and compared with their structures in solution well above their critical micelle concentration. The differences in the nature of the various anions of the four Bzth-X materials lead to unique anion environments and 3-D molecular arrangements. The water molecule in the monoclinic Bzth-Cl or Bzth-Br forms is hydrogen bonded to the halides and particularly to the hydrogens of the methoxy groups of the Bzth moiety notwithstanding the weak Brønsted acidity of the methoxy hydrogens. The citrate strongly interacts with the hydrogens of the methoxy group forming an embedded anionic spherical cluster of a radius of 2.6 Å. The Bzth-OH crystallizes in a hexagonal lattice with two water molecules and reveals free water molecules forming hydrogen bonded channels through the Bzth-OH crystal along the c-axis. The distances between the cationic nitrogen and the halides are 4.04 Å and 4.20 Å, significantly longer than expected for typical van der Waals distances of 3.30 Å. The structures show weakly interacting, alternating apolar and polar layers, which run parallel to the crystallographic a-b planes or a-c planes. The Bzth-X salts were also examined in aqueous solution containing 20% (v/v) ethanol and 1.0 % (v/v) glycerol well above their critical micelle concentration by small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS). The [1,1,1] planes for the Bzth Cl or Br, the [0,0,2] and [1,1,0] planes for the Bzth-citrate, the [2,-1,0] planes and the [0,0,1] planes for the Bzth-OH found in the crystalline phase were also present in the solution phase, accordingly, the preservation of these phases are a strong indication of periodicity in the solution phase.

  9. Enthalpies of Solution of Complexes of Rare Earth Nitrate with L-α-Histidine in Water

    Institute of Scientific and Technical Information of China (English)

    刘洋; 房艳; 高胜利; 陈三平; 史启祯

    2002-01-01

    The enthalpies of solution in water of complexes of RE(NO3)3 (RE=La~Nd, Sm~Lu, Y) with L-α-Histidine (His) were measured at 298.15 K. The standard enthalpies of formation of RE(His)3+(aq) were calculated. The "tetrad effect" regularity was observed from the curve, which is the enthalpies of solution plotted against the atomic numbers of the elements in lanthanide series.

  10. Luminescence properties of solid solutions of borates doped with rare-earth ions

    Science.gov (United States)

    Levushkina, V. S.; Mikhailin, V. V.; Spassky, D. A.; Zadneprovski, B. I.; Tret'yakova, M. S.

    2014-11-01

    The structural and luminescence properties of LuxY1 - xBO3 solid solutions doped with Ce3+ or Eu+3 have been investigated. It has been found that the solid solutions crystallize in the vaterite phase with a lutetium concentration x spectra are characterized by intensive impurity emission under excitation with the synchrotron radiation in the X-ray and ultraviolet spectral ranges. It has been shown that, as the lutetium concentration x in the LuxY1 - xBO3: Ce3+ solid solutions increases, the emission intensity smoothly decreases, which is associated with a gradual shift of the Ce3+ 5 d(1) level toward the bottom of the conduction band, as well as with a decrease in the band gap. It has been established that, in the LuxY1 - xBO3: Eu3+ solid solutions with intermediate concentrations x, the efficiency of energy transfer to luminescence centers increases. This effect is explained by the limited spatial separation of electrons and holes in the solid solutions. It has been demonstrated that the calcite phase adversely affects the luminescence properties of the solid solutions.

  11. Relationship between Scattered Photon Counts and Concentrations of Some Saline Solutions in Compton Scattering

    Institute of Scientific and Technical Information of China (English)

    LUO Guang; ZHOU Shang-Qi; HAN Zhong; CHEN Shuang-Kou

    2007-01-01

    Compton scattering saline solution was researched.Firstly according to the Compton scattering theory the linear relationship between the concentration and the scattered photon counts was obtained.And then it was proved by Compton scattering experiments for some solutions.According to those experiments, it was found that the slope was decreased when the atomic number of the cation was increased for alkali metal chloride solutions and alkaline-earth metal chloride solutions.Based on those relationships,a new method was promoted with which to measure the concentration of saline solution untouched the measured solution.

  12. A combined GPS/GLONASS global solution for the determination of diurnal and semi-diurnal Earth rotation variations

    Science.gov (United States)

    Englich, S.; Weber, R.; Schuh, H.

    2009-04-01

    Due to the global distribution of the IGS stations and the availability of continuous tracking data, GNSS observation data is very well suited for the investigation of high-frequency variations of the Earth rotation parameters (ERP). The majority of obtainable observations stems from the GPS system, but the number of stations equipped with combined GPS/GLONASS receivers is steadily increasing. One drawback in GPS only studies is that the orbital period of the GPS satellites is in a deep 2:1 resonance with Earth rotation. Consequently orbital errors which propagate to the ERP estimation limit the accurate determination of ERP variations in this frequency band (K1, K2). The purpose of this study is to make use of the rising availability of globally distributed GLONASS data for investigating the benefits of a combined GPS/GLONASS approach for the examination of diurnal and semi-diurnal Earth rotation variations. The observation data of 2008 from more than 120 IGS sites, of which around one third track GPS as well as GLONASS satellites, was chosen for analysis. We compared coordinate repeatabilities, ERP, and subsequently derived tidal variations calculated from a GPS stand-alone and a combined GPS/GLONASS solution.

  13. Earth Rotation Parameter Solutions using BDS and GPS Data from MEGX Network

    Science.gov (United States)

    Xu, Tianhe; Yu, Sumei; Li, Jiajing; He, Kaifei

    2014-05-01

    Earth rotation parameters (ERPs) are necessary parameters to achieve mutual transformation of the celestial reference frame and earth-fix reference frame. They are very important for satellite precise orbit determination (POD), high-precision space navigation and positioning. In this paper, the determination of ERPs including polar motion (PM), polar motion rate (PMR) and length of day (LOD) are presented using BDS and GPS data of June 2013 from MEGX network based on least square (LS) estimation with constraint condition. BDS and GPS data of 16 co-location stations from MEGX network are the first time used to estimate the ERPs. The results show that the RMSs of x and y component errors of PM and PM rate are about 0.9 mas, 1.0 mas, 0.2 mas/d and 0.3 mas/d respectively using BDS data. The RMS of LOD is about 0.03 ms/d using BDS data. The RMSs of x and y component errors of PM and PM rate are about 0.2 mas, 0.2 mas/d respectively using GPS data. The RMS of LOD is about 0.02 ms/d using GPS data. The optimal relative weight is determined by using variance component estimation when combining BDS and GPS data. The accuracy improvements of adding BDS data is between 8% to 20% for PM and PM rate. There is no obvious improvement in LOD when BDS data is involved. System biases between BDS and GPS are also resolved per station. They are very stable from day to day with the average accuracy of about 20 cm. Keywords: Earth rotation parameter; International GNSS Service; polar motion; length of day; least square with constraint condition Acknowledgments: This work was supported by Natural Science Foundation of China (41174008) and the Foundation for the Author of National Excellent Doctoral Dissertation of China (2007B51) .

  14. Tests of daily time variable Earth gravity field solutions for precise orbit determination of altimetry satellites

    Science.gov (United States)

    Rudenko, Sergei; Gruber, Christian

    2016-04-01

    This study makes use of current GFZ monthly and daily gravity field products from 2002 to 2014 based on radial basis functions (RBF) instead of time variable gravity field modeling for precise orbit determination of altimetry satellites. Since some monthly solutions are missing in the GFZ GRACE RL05a solution and in order to reach a better quality for the precise orbit determination, daily generated RBF solutions obtained from Kalman filtered GRACE data processing and interpolated in case of gaps have been used. Moreover, since the geopotential coefficients of low degrees are better determined using SLR observations to geodetic satellites like Lageos, Stella, Starlette and Ajisai than from GRACE observations, these terms are co-estimated in the RBF solutions by using apriori SLR-derived values up to degree and order 4. Precise orbits for altimetry satellites Envisat (2002-2012), Jason-1 (2002-2013) and Jason-2 (2008-2014) are then computed over the given time intervals using this approach and compared with the orbits obtained when using other models such as EIGEN-6S4. An analysis of the root-mean-square values of the observation fits of SLR and DORIS observations and the orbit arcs overlaps will allow us to draw a conclusion on the quality of the RBF solution and to use these new trajectories for sea level trend estimates and geophysical application.

  15. 肌醇在氯化钠水溶液中的稀释焓和焓对相互作用%Dilution Enthalpy and Pairwise Enthalpic Interaction of Myo-inositol in Aqueous Sodium Chloride Solution

    Institute of Scientific and Technical Information of China (English)

    郑文清; 曲秀葵; 孙德志∗

    2008-01-01

      The dilution enthalpies of myo-inositol in water and aqueous sodium chloride solutions had been determined with flow–mix-isothermal microcalorimetry at 298.15 K. The enthalpic interaction coefficients in the different concentrations of sodium chloride had been calculated according to the McMillan-Mayer theory. The results showed that enthalpic pairwise interaction coefficients (h2) of myo-inositol are negative in aqueous sodium chloride solutions and values of h2 become more positive with increasing the concentration of sodium chloride. It could be interpreted in terms of interactions of solute with solute and solute with solvent.%  应用微量热法测定了298.15 K时肌醇在纯水和氯化钠水溶液中的稀释焓,根据McMillan-Mayer 理论计算了肌醇在不同浓度的氯化钠溶液中的2到4阶焓相互作用系数.结果表明,肌醇在氯化钠溶液中的焓对相互作用系数h2均为负值,并且随着氯化钠浓度的增大, h2的值呈增大趋势.根据溶质-溶质相互作用和溶质-溶剂相互作用对焓对相互作用系数的变化趋势进行了解释.

  16. The Shortlist Method for fast computation of the Earth Mover's Distance and finding optimal solutions to transportation problems.

    Directory of Open Access Journals (Sweden)

    Carsten Gottschlich

    Full Text Available Finding solutions to the classical transportation problem is of great importance, since this optimization problem arises in many engineering and computer science applications. Especially the Earth Mover's Distance is used in a plethora of applications ranging from content-based image retrieval, shape matching, fingerprint recognition, object tracking and phishing web page detection to computing color differences in linguistics and biology. Our starting point is the well-known revised simplex algorithm, which iteratively improves a feasible solution to optimality. The Shortlist Method that we propose substantially reduces the number of candidates inspected for improving the solution, while at the same time balancing the number of pivots required. Tests on simulated benchmarks demonstrate a considerable reduction in computation time for the new method as compared to the usual revised simplex algorithm implemented with state-of-the-art initialization and pivot strategies. As a consequence, the Shortlist Method facilitates the computation of large scale transportation problems in viable time. In addition we describe a novel method for finding an initial feasible solution which we coin Modified Russell's Method.

  17. The Shortlist Method for fast computation of the Earth Mover's Distance and finding optimal solutions to transportation problems.

    Science.gov (United States)

    Gottschlich, Carsten; Schuhmacher, Dominic

    2014-01-01

    Finding solutions to the classical transportation problem is of great importance, since this optimization problem arises in many engineering and computer science applications. Especially the Earth Mover's Distance is used in a plethora of applications ranging from content-based image retrieval, shape matching, fingerprint recognition, object tracking and phishing web page detection to computing color differences in linguistics and biology. Our starting point is the well-known revised simplex algorithm, which iteratively improves a feasible solution to optimality. The Shortlist Method that we propose substantially reduces the number of candidates inspected for improving the solution, while at the same time balancing the number of pivots required. Tests on simulated benchmarks demonstrate a considerable reduction in computation time for the new method as compared to the usual revised simplex algorithm implemented with state-of-the-art initialization and pivot strategies. As a consequence, the Shortlist Method facilitates the computation of large scale transportation problems in viable time. In addition we describe a novel method for finding an initial feasible solution which we coin Modified Russell's Method.

  18. Separation of middle rare earths by solvent extraction using 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester as an extractant

    Institute of Scientific and Technical Information of China (English)

    Danilo; Fontana; Loris; Pietrelli

    2009-01-01

    The extraction of the trivalent middle rare earths from chloride media by kerosene solutions of 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester as an extractant was studied. The separation factors between the elements using solution simulating wastes from NiMH spent batteries have been evaluated: the order of the extractive ability of extractant can be confirmed in ThGdEuSm.

  19. Study on the Cooling System of the Engine with the Solution of Calcium Chloride%以氯化钙溶液为冷却液的发动机冷却系统研究

    Institute of Scientific and Technical Information of China (English)

    乔亚宾; 朱鑫宇; 马兴远

    2015-01-01

    According to the solution, the boiling point of the solution is higher than that of the organic solvent, and the freezing point is lower than the organic solvent solution. Through the study of the physical properties of the calcium chloride solution, combined with the popular ethylene glycol type cooling liquid, the feasibility of the solution is studied. Calcium chloride solution has a certain corrosion, the engine cooling system is made of new material, the theoretical performance analysis and experimental results show that the use of suitable calcium chloride solution can replace ethylene glycol type coolant, as a new type of engine cooling liquid.%根据溶液的依数性可知,相同浓度的溶液,电解质溶液的沸点高于有机溶剂溶液,冰点低于有机溶剂溶液,更符合发动机冷却系统对冷却液的基本要求。通过对氯化钙溶液物性的研究,结合市面上流行的乙二醇型冷却液的性能,探究氯化钙溶液作为车用冷却液的可行性。氯化钙溶液有一定的腐蚀性,采用新材料制作的发动机冷却系统,通过材料的理论性能分析和实验结果表明,采用合适的技术氯化钙溶液完全可以替代乙二醇型冷却液,作为新型的发动机冷却液使用。

  20. DNA-gelatin complex coacervation, UCST and first-order phase transition of coacervate to anisotropic ion gel in 1-methyl-3-octylimidazolium chloride ionic liquid solutions.

    Science.gov (United States)

    Rawat, Kamla; Aswal, V K; Bohidar, H B

    2012-12-27

    Study of kinetics of complex coacervation occurring in aqueous 1-octyl-3-methylimidazolium chloride ionic liquid solution of low charge density polypeptide (gelatin A) and 200 base pair DNA, and thermally activated coacervate into anisotropic gel transition, is reported here. Associative interaction between DNA and gelatin A (GA) having charge ratio (DNA:GA = 16:1) and persistence length ratio (5:1) was studied at fixed DNA (0.005% (w/v)) and varying GA concentration (C(GA) = 0-0.25% (w/v)). The interaction profile was found to be strongly hierarchical and revealed three distinct binding regions: (i) Region I showed DNA-condensation (primary binding) for C(GA) coacervation. (iii) Region III (0.15 coacervate was found to be protein concentration specific in Raman studies. The binding profile of DNA-GA complex with IL concentration revealed optimum IL concentration (=0.05% (w/v)) was required to maximize the interactions. Small angle neutron scattering (SANS) data of coacervates gave static structure factor profiles, I(q) versus wave vector q, that were remarkably similar and invariant of protein concentration. This data could be split into two distinct regions: (i) for 0.0173 coacervate phase resided close to the gelation state of the protein. Thus, on a heating-cooling cycle (heating to 50 °C followed by cooling to 20 °C), the heterogeneous coacervate exhibited an irreversible first-order phase transition to an anisotropic ion gel. This established a coacervate-ion gel phase diagram having a well-defined UCST.

  1. A systemic study of stepwise chlorination-chemical vapor transport characteristics of pure rare earth oxides from Sc{sub 2}O{sub 3} to Lu{sub 2}O{sub 3} mediated by alkaline chlorides as complex former

    Energy Technology Data Exchange (ETDEWEB)

    Sun Yanhui [School of Chemistry and Environment, South China Normal University, Guangzhou 510631 (China)]. E-mail: sunyanhui0102@163.com; He Peng [Department of Ecology, School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Chen Huani [School of Chemistry and Environment, South China Normal University, Guangzhou 510631 (China)

    2007-08-30

    A systematic study has been carried out for the stepwise chlorination-chemical vapor transport (SC-CVT) characteristics of pure rare earth oxides from Sc{sub 2}O{sub 3} to Lu{sub 2}O{sub 3} mediated by the vapor complexes KLnCl{sub 4} and NaLnCl{sub 4} (Ln = Sc, Y and La-Lu) used NaCl and KCl as complex former, respectively. The results showed that the SC-CVT characteristics are similarly for NaCl and KCl as complex former, the main deposition temperature of the rare earth chlorides LnCl{sub 3} is in the increasing order ScCl{sub 3} < YCl{sub 3} < LaCl{sub 3}, and then with a systematically decreasing trend from the early lanthanide chlorides to the end one. The results also showed that the total transported amount of the produced chlorides is YCl{sub 3} > ScCl{sub 3}, and they are much higher than that of most lanthanoid chlorides. For lanthanoids, the total transported amount of chloride increases systematically from the early lanthanoid chlorides to the end one except for EuCl{sub 3} and GdCl{sub 3} mediated by KCl and NaCl as complex former, respectively, which showed the divergence effect of Gd in the total transport efficiency. But there are some differences in SC-CVT characteristics of pure rare earth oxide mediated by KCl and NaCl as complex former, that is the main deposition temperature region for the same rare earth element was lower for KCl than that for NaCl as complex former except for LaCl{sub 3}, CeCl{sub 3}, YbCl{sub 3} and LuCl{sub 3}, while the total transport amount of rare earth chloride for KCl as complex former is higher than that for NaCl except for LaCl{sub 3} and EuCl{sub 3}. More over, the discussion was carried out for Sc and Y on the one hand and the lanthanides contain 4f electron as another hand based on the 4f electron hybridization assumption. Further more, the transport characteristics of rare earth oxides with alkaline chlorides as complex former in this study were compared to that with AlCl{sub 3} as complex former.

  2. Rare earth elements in sedimentary phosphate deposits: Solution to the global REE crisis?

    Science.gov (United States)

    Emsbo, Poul; McLaughlin, Patrick I.; Breit, George N.; du Bray, Edward A.; Koenig, Alan E.

    2015-01-01

    The critical role of rare earth elements (REEs), particularly heavy REEs (HREEs), in high-tech industries has created a surge in demand that is quickly outstripping known global supply and has triggered a worldwide scramble to discover new sources. The chemical analysis of 23 sedimentary phosphate deposits (phosphorites) in the United States demonstrates that they are significantly enriched in REEs. Leaching experiments using dilute H2SO4 and HCl, extracted nearly 100% of their total REE content and show that the extraction of REEs from phosphorites is not subject to the many technological and environmental challenges that vex the exploitation of many identified REE deposits. Our data suggest that phosphate rock currently mined in the United States has the potential to produce a significant proportion of the world's REE demand as a byproduct. Importantly, the size and concentration of HREEs in some unmined phosphorites dwarf the world's richest REE deposits. Secular variation in phosphate REE contents identifies geologic time periods favorable for the formation of currently unrecognized high-REE phosphates. The extraordinary endowment, combined with the ease of REE extraction, indicates that such phosphorites might be considered as a primary source of REEs with the potential to resolve the global REE (particularly for HREE) supply shortage.

  3. Probing Earth's conductivity structure beneath oceans by scalar geomagnetic data: autonomous surface vehicle solution

    Science.gov (United States)

    Kuvshinov, Alexey; Matzka, Jürgen; Poedjono, Benny; Samrock, Friedemann; Olsen, Nils; Pai, Sudhir

    2016-11-01

    The electric conductivity distribution of the Earth's crust and upper mantle provides a key to unraveling its structure. Information can be obtained from vector data time series of the natural variations of the magnetic and electric field in a directional stable reference frame. Applying this method, known as magnetotellurics, to oceanic regions is challenging since only vector instruments placed at the sea bottom can provide such data. Here, we discuss a concept of marine induction surveying which is based on sea-surface scalar magnetic field measurements from a modern position-keeping platform. The concept exploits scalar magnetic responses that relate variations of the scalar magnetic field at the survey sites with variations of the horizontal magnetic field at a reference site. A 3-D model study offshore Oahu Island (Hawaii) demonstrates that these responses are sensitive to the conductivity structure beneath the ocean. We conclude that the sensitivity, depending on the bathymetry gradient, is typically largest near the coast offshore. We show that such sea-surface marine induction surveys can be performed with the Wave Glider, an easy-to-deploy, autonomous, energy-harvesting floating platform with position-keeping capability.[Figure not available: see fulltext.

  4. Laboratory Evaluation of the Clean Earth Technologies Decontamination Solutions for Chemical and Biological Agents

    Science.gov (United States)

    2008-01-01

    about a 6-hr shelf - life before simulant decontamination efficacy begins to decline. The purpose of this test was to evaluate two CET decontamination...Store in a sealed beaker 2) PeridoxTM stock - Dilute (1: 10) CET in water 3) Titrant - 0.1 N sodium thiosulfate 4) Potassium iodide crystals...Procedure: To 50 mL of water in a beaker, add 1 mL of dilute CET followed by 2.5 mL of acid solution, and then 0.6 g of potassium iodide crystals. Titrate

  5. 氯化钙废液回收氯化钙中氯化铵残留的原因分析及解决措施%Calcium Chloride Ammonium Chloride Waste Recycling Calcium Chloride Residual Analysis of the Causes and Solutions

    Institute of Scientific and Technical Information of China (English)

    安彩妹; 李兴波; 陈晓飞; 刘春静

    2015-01-01

    This paper expounds the cyanuric chloride calcium chloride liquid waste recycling process during production. For the reason of recycle calcium chloride ammonium chloride in the residual analysis,determines the final cause of the recovery of calcium chloride ammonium chloride content in the high drying temperature and time are not enough. In neutral pH control 10,reduce enrichment of ammonium chloride in the process of residue. Control in the process of drying temperature of 260 degrees celsius,the calcium chloride wet even after recycling. Control drying time at 24 hours, ammonium chloride content can be calcium chloride content more than 98%,and 0. 05% of the calcium chloride. Reach the standard workshop of calcium chloride recycle,completely solve production using calcium chloride with ammonium chloride and high block of the dryer.%阐述了三聚氯氰生产过程中氯化钙废液的回收工艺。对回收氯化钙中氯化铵的残留进行了原因分析,确定了导致回收氯化钙中氯化铵含量高的最终原因是烘干温度和时间不够。在中和时控制pH值10,减少浓缩过程中氯化铵的残留。在烘干过程中控制温度达到260℃,使回收后氯化钙干湿均匀。控制烘干时间达到24h,可以得到氯化钙含量>98%、氯化铵含量<0.05%的回收氯化钙。达到车间氯化钙循环使用标准,彻底解决生产使用回收氯化钙因氯化铵含量高造成干燥器堵塞的问题。

  6. Effect of Chloride Type on Penetration of Chloride Ions in Concrete

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The influence of chloride type on the diffusivity of chloride ions in concrete was studied by experiment. The result shows that the glectric resistance of concrete and the chloride diffusion coefficient are influenced by chloride type. For the same water/cement ratio (W/C), the diffusion coefficient D in KCl solution is larger than that in NaCl solution; however, the concrete resistance in KCl solution is smaller than that in NaCl solution. The experimental result is analyzed with theory of diffusion.

  7. An analytical solution for the elastic response to surface loads imposed on a layered, transversely isotropic and self-gravitating Earth

    DEFF Research Database (Denmark)

    Pan, E.; Chen, J.Y.; Bevis, M.

    2015-01-01

    the correctness of our solution and the implementation. We also calculate the load Love numbers (LLNs) of the PREM Earth for different degrees of the Legendre function for both isotropic and transversely isotropic, layered mantles with different core models, demonstrating for the first time the effect of Earth......We present an analytical solution for the elastic deformation of an elastic, transversely isotropic, layered and self-gravitating Earth by surface loads. We first introduce the vector spherical harmonics to express the physical quantities in the layered Earth. This reduces the governing equations...... to a linear system of equations for the expansion coefficients. We then solve for the expansion coefficients analytically under the assumption (i.e. approximation) that in the mantle, the density in each layer varies as 1/r (where r is the radial coordinate) while the gravity is constant and that in the core...

  8. Stability Study of Rare Earth Elements in Electroless Nickel Solution%无电解镀镍液稳定性研究

    Institute of Scientific and Technical Information of China (English)

    邵国强

    2014-01-01

    Some research developments about rare earth elements on the stability of electroless nickel solution was reviewed. Influence factor and action mechanism of rare earth elements were also introduced.%综述了稀土在提高无电解镀镍液稳定性中的研究进展,并分析了稀土促进镀液稳定性的影响因素和作用机理。

  9. Chloride transference during electrochemical chloride extraction process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Chemical titration method and lab-made chloride probes were jointly adopted to investigate the effects of water-to-cement (W/C) ratio and the impressed current density on chloride transport for cement-based materials during electrochemical chloride extraction (ECE) process.The dissolution of bound chlorides and the effect of current density on dissolution were analyzed.The variations of chloride concentration at different depths and the chloride transference process were monitored.Test results show that W/C ratios adopted have slight influence on chloride extraction,while chloride extraction efficiency is mainly determined by the impressed current density.During ECE process a portion of bound chloride ions dissolved and the amount of bound chlorides released is directly proportional to current density.

  10. Effectiveness of ophthalmic solution preservatives: a comparison of latanoprost with 0.02% benzalkonium chloride and travoprost with the sofZia preservative system

    Directory of Open Access Journals (Sweden)

    Lovelace Cherie

    2011-04-01

    Full Text Available Abstract Background Although in vitro and in vivo laboratory studies have suggested that benzalkonium chloride (BAK in topical ophthalmic solutions may be detrimental to corneal epithelial cells, multiple short- and long-term clinical studies have provided evidence supporting the safety of BAK. Despite the conflicting evidence, BAK is the most commonly used preservative in ophthalmic products largely due to its proven antimicrobial efficacy. This study was designed to characterize the antimicrobial performance of two commonly used topical ocular hypotensive agents that employ different preservative systems: latanoprost 0.005% with 0.02% BAK and travoprost 0.004% with sofZia, a proprietary ionic buffer system. Methods Each product was tested for antimicrobial effectiveness by European Pharmacopoeia A (EP-A standards, the most stringent standards of the three major compendia, which specify two early sampling time points (6 and 24 hours not required by the United States Pharmacopeia or Japanese Pharmacopoeia. Aliquots were inoculated with between 105 and 106 colony-forming units of the test organisms: Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, Candida albicans and Aspergillus brasiliensis. Sampling and enumeration were conducted at protocol-defined time points through 28 days. Results BAK-containing latanoprost met EP-A criteria by immediately reducing all bacterial challenge organisms to the test sensitivity and fungal challenges within the first six hours while the preservative activity of travoprost with sofZia did not. Complete bacterial reduction by travoprost with sofZia was not shown until seven days into the test, and fungal reduction never exceeded the requisite 2 logs during the 28-day test. Travoprost with sofZia also did not meet EP-B criteria due to its limited effectiveness against Staphylococcus aureus. Both products satisfied United States and Japanese pharmacopoeial criteria. Conclusions Latanoprost with 0

  11. Effectiveness of ophthalmic solution preservatives: a comparison of latanoprost with 0.02% benzalkonium chloride and travoprost with the sofZia preservative system

    Science.gov (United States)

    2011-01-01

    Background Although in vitro and in vivo laboratory studies have suggested that benzalkonium chloride (BAK) in topical ophthalmic solutions may be detrimental to corneal epithelial cells, multiple short- and long-term clinical studies have provided evidence supporting the safety of BAK. Despite the conflicting evidence, BAK is the most commonly used preservative in ophthalmic products largely due to its proven antimicrobial efficacy. This study was designed to characterize the antimicrobial performance of two commonly used topical ocular hypotensive agents that employ different preservative systems: latanoprost 0.005% with 0.02% BAK and travoprost 0.004% with sofZia, a proprietary ionic buffer system. Methods Each product was tested for antimicrobial effectiveness by European Pharmacopoeia A (EP-A) standards, the most stringent standards of the three major compendia, which specify two early sampling time points (6 and 24 hours) not required by the United States Pharmacopeia or Japanese Pharmacopoeia. Aliquots were inoculated with between 105 and 106 colony-forming units of the test organisms: Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, Candida albicans and Aspergillus brasiliensis. Sampling and enumeration were conducted at protocol-defined time points through 28 days. Results BAK-containing latanoprost met EP-A criteria by immediately reducing all bacterial challenge organisms to the test sensitivity and fungal challenges within the first six hours while the preservative activity of travoprost with sofZia did not. Complete bacterial reduction by travoprost with sofZia was not shown until seven days into the test, and fungal reduction never exceeded the requisite 2 logs during the 28-day test. Travoprost with sofZia also did not meet EP-B criteria due to its limited effectiveness against Staphylococcus aureus. Both products satisfied United States and Japanese pharmacopoeial criteria. Conclusions Latanoprost with 0.02% BAK exhibited more

  12. Fundamental solution of Laplace's equation in oblate spheroidal coordinates and Galerkin's matrix for Neumann's problem in Earth's gravity field studies

    Science.gov (United States)

    Holota, Petr; Nesvadba, Otakar

    2015-04-01

    In this paper the reciprocal distance is used for generating Galerkin's approximations in the weak solution of Neumann's problem that has an important role in Earth's gravity field studies. The reciprocal distance has a natural tie to the fundamental solution of Laplace's partial differential equation and in the paper it is represented by means of an expansion into a series of oblate spheroidal harmonics. Subsequently, the gradient vector of the reciprocal distance is constructed. In the computation of its components the expansion mentioned above is employed. The paper then focuses on the scalar product of reciprocal distance gradients in two different points and in particular on a series representation of a volume integral of the scalar product spread over an unbounded domain given by the exterior of an oblate spheroid (oblate ellipsoid of revolution). The integral yields the entries of Galerkin's matrix. The numerical interpretation of all the expansions used as well as the respective software implementation within the OpenCL framework is treated, which concerns also a numerical evaluation of Legendre functions of a real and an imaginary argument. In parallel an approximate closed formula expressing the entries of Galerkin's matrix (with an accuracy up to terms multiplied by the square of numerical eccentricity) is derived for convenience and comparison. The paper is added extensive numerical examples that illustrate the approach applied and demonstrate the accuracy of the derived formulas. Aspects related to practical applications are discussed.

  13. On the formation and structure of rare-earth element complexes in aqueous solutions under hydrothermal conditions with new data on gadolinium aqua and chloro complexes

    Science.gov (United States)

    Mayanovic, Robert A.; Anderson, Alan J.; Bassett, William A.; Chou, I.-Ming

    2007-01-01

    Synchrotron X-ray spectroscopy experiments were made on the Gd(III) aqua and chloro complexes in low pH aqueous solutions at temperatures ranging from 25 to 500????C and at pressures up to 480??MPa using a hydrothermal diamond anvil cell. Analysis of fluorescence Gd L3-edge X-ray absorption fine structure (XAFS) spectra measured from a 0.006m Gd/0.16m HNO3 aqueous solution at temperatures up to 500????C and at pressures up to 260??MPa shows that the Gd-O distance of the Gd3+ aqua ion decreases steadily at a rate of ??? 0.007??A??/100????C whereas the number of coordinated H2O molecules decreases from 9.0 ?? 0.5 to 7.0 ?? 0.4. The loss of water molecules in the Gd3+ aqua ion inner hydration shell over this temperature range (a 22% reduction) is smaller than exhibited by the Yb3+ aqua ion (42% reduction) indicating that the former is significantly more stable than the later. We conjecture that the anomalous enrichment of Gd reported from measurement of REE concentrations in ocean waters may be attributed to the enhanced stability of the Gd3+ aqua ion relative to other REEs. Gd L3-edge XAFS measurements of 0.006m and 0.1m GdCl3 aqueous solutions at temperatures up to 500????C and pressures up to 480??MPa reveal that the onset of significant Gd3+-Cl- association occurs around 300????C. Partially-hydrated stepwise inner-sphere complexes most likely of the type Gd(H2O)??-nCln+3-n occur in the chloride solutions at higher temperatures, where ?? ??? 8 at 300????C decreasing slightly to an intermediate value between 7 and 8 upon approaching 500????C. This is the first direct evidence for the occurrence of partially-hydrated REE Gd (this study) and Yb [Mayanovic, R.A., Jayanetti, S., Anderson, A.J., Bassett, W.A., Chou, I-M., 2002a. The structure of Yb3+ aquo ion and chloro complexes in aqueous solutions at up to 500 ??C and 270 MPa. J. Phys. Chem. A 106, 6591-6599.] chloro complexes in hydrothermal solutions. The number of chlorides (n) of the partially-hydrated Gd

  14. Studies on extracting solutions of endohedral rare-earth metallofullerenes by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

    Institute of Scientific and Technical Information of China (English)

    孙大勇; 刘志强; 刘子阳; 郭兴华; 徐文国; 刘淑莹

    1997-01-01

    Thirteen extracting solutions of rare-earth metallofullerenes containing La,Ce,Pr,Nd Sm,Eu,Gd,Tb,Dy,Ho,Er,Tm and Yb respectively have been investigated by means of matrix-assisted laser desorpuon/ ionization time-of-flight mass spectrometry.The influences of the positive-ion/negative-ion mode,laser intensity,ma trix and mass discrimination to the analytical results are studied,based on which the optimal analytical conditions have been determined.The results show that the extracting solutions contain large quantities of rare-earth metallofullerenes besides empty fullerenes.On the basis of comparing their relative intensities,the different structure stabilities and solubilities of metallofullerenes with different rare-earth metals encapsulated into the fullerene cages,as well as some possible reasons to those differences,are discussed.

  15. A STUDY ON INTERACTION OF Cd(II) AND DIATOMACEOUS EARTH IN ADSORPTION PROCESS

    OpenAIRE

    Nuryono, Nuryono; Suyanta, Suyanta

    2010-01-01

    In this research, interaction occurring in adsorption process between Cd(II) and active site of diatomaceous earth has been studied. The study was carried out by evaluating Cd(II) adsorption on diatomaceous earth at various pHs, either for the earths without treatment, those after being heated or those treated with sulfuric acid and hydrogen chloride. Adsorption was performed by mixing diatomaceous earth, without and with treatments, and Cd(II) solution for one hour at various pHs (2 - 7), an...

  16. Tribenzylammonium chloride

    Directory of Open Access Journals (Sweden)

    Waly Diallo

    2014-05-01

    Full Text Available Single crystals of the title salt, C21H21NH+·Cl−, were isolated as a side product from the reaction involving [(C6H5CH23NH]2[HPO4] and Sn(CH33Cl in ethanol. Both the cation and the anion are situated on a threefold rotation axis. The central N atom in the cation has a slightly distorted tetrahedral environment, with angles ranging from 107.7 to 111.16 (10°. In the crystal, the tribenzylammonium cations and chloride anions are linked through N—H...Cl and C—H...Cl hydrogen bonds, leading to the formation of infinite chains along [001]. The crystal studied was a merohedral twin.

  17. Low Temperature Preparation of Ceria Solid Solutions Doubly Doped with Rare-Earth and Alkali-Earth and Their Properties as Solid Oxide Fuel Cells

    Institute of Scientific and Technical Information of China (English)

    任引哲; 蒋凯; 王海霞; 孟健; 苏锵

    2003-01-01

    A series of solid electrolytes, (Ce0.8Ln0.2)1-xMxO2-δ (Ln= La, Nd, Sm, Gd, M:Alkali-earth), were prepared by amorphous citrate gel method. XRD patterns indicate that a pure fluorite phase is formed at 800 ℃. The electrical conductivity and the AC impedance spectra were measured. XPS spectra show that the oxygen vacancies increase owing to the MO doping, which results in the increase of the oxygen ionic transport number and conductivity. The performance of ceria-based solid electrolyte is improved. The effects of rare-earth and alkali-earth ions on the electricity were discussed. The open-circuit voltages and maximum power density of planar solid oxide fuel cell using (Ce0.8Sm0.2)1-0.05Ca0.05O2-δ as electrolyte are 0.86 V and 33 mW*cm-2, respectively.

  18. Chemically Inhomogeneous RE-Fe-B Permanent Magnets with High Figure of Merit: Solution to Global Rare Earth Criticality.

    Science.gov (United States)

    Jin, Jiaying; Ma, Tianyu; Zhang, Yujing; Bai, Guohua; Yan, Mi

    2016-08-24

    The global rare earth (RE) criticality, especially for those closely-relied Nd/Pr/Dy/Tb in the 2:14:1-typed permanent magnets (PMs), has triggered tremendous attempts to develop new alternatives. Prospective candidates La/Ce with high abundance, however, cannot provide an equivalent performance due to inferior magnetic properties of (La/Ce)2Fe14B to Nd2Fe14B. Here we report high figure-of-merit La/Ce-rich RE-Fe-B PMs, where La/Ce are inhomogeneously distributed among the 2:14:1 phase. The resultant exchange coupling within an individual grain and magnetostatic interactions across grains ensure much superior performance to the La/Ce homogeneously distributed magnet. Maximum energy product (BH)max of 42.2 MGOe is achieved even with 36 wt. % La-Ce incorporation. The cost performance, (BH)max/cost, has been raised by 27.1% compared to a 48.9 MGOe La/Ce-free commercial magnet. The construction of chemical heterogeneity offers recipes to develop commercial-grade PMs using the less risky La/Ce, and also provides a promising solution to the REs availability constraints.

  19. Chemically Inhomogeneous RE-Fe-B Permanent Magnets with High Figure of Merit: Solution to Global Rare Earth Criticality

    Science.gov (United States)

    Jin, Jiaying; Ma, Tianyu; Zhang, Yujing; Bai, Guohua; Yan, Mi

    2016-08-01

    The global rare earth (RE) criticality, especially for those closely-relied Nd/Pr/Dy/Tb in the 2:14:1-typed permanent magnets (PMs), has triggered tremendous attempts to develop new alternatives. Prospective candidates La/Ce with high abundance, however, cannot provide an equivalent performance due to inferior magnetic properties of (La/Ce)2Fe14B to Nd2Fe14B. Here we report high figure-of-merit La/Ce-rich RE-Fe-B PMs, where La/Ce are inhomogeneously distributed among the 2:14:1 phase. The resultant exchange coupling within an individual grain and magnetostatic interactions across grains ensure much superior performance to the La/Ce homogeneously distributed magnet. Maximum energy product (BH)max of 42.2 MGOe is achieved even with 36 wt. % La-Ce incorporation. The cost performance, (BH)max/cost, has been raised by 27.1% compared to a 48.9 MGOe La/Ce-free commercial magnet. The construction of chemical heterogeneity offers recipes to develop commercial-grade PMs using the less risky La/Ce, and also provides a promising solution to the REs availability constraints.

  20. Corrosion of Reinforcing Steel in Concrete Immersed in Chloride Solution and the Effects of Detergent Additions on Diffusion and Concrete Porosity

    OpenAIRE

    2002-01-01

    In order to investigate the corrosion of reinforcing steel in concrete and the effects of chloride ions, oxygen diffusion and detergent additives of linear alkylbenzene (LAB) and linear alkylbenzene sulfonate (LAS), potentiokinetic experiments were carried out. Thus, by embedding steel electrodes into concrete specimens with a water/cement (W/C) ratio of 0.45, current-potential curves were obtained and the compressive strength of the specimens was measured. The electrochemical appro...

  1. Synergism between rare earth cerium(IV) ion and vanillin on the corrosion of cold rolled steel in 1.0 M HCl solution

    Energy Technology Data Exchange (ETDEWEB)

    Li Xianghong [Department of Fundamental Courses, Southwest Forestry University, Kunming 650224 (China)], E-mail: xianghong-li@163.com; Deng Shuduan [Department of Wood Science and Technology, Southwest Forestry University, Kunming 650224 (China); Fu Hui [Department of Fundamental Courses, Southwest Forestry University, Kunming 650224 (China); Mu Guannan [Department of Chemistry, Yunnan University, Kunming 650091 (China)

    2008-12-15

    The synergism between rare earth cerium(IV) ion and vanillin on the corrosion of cold rolled steel (CRS) in 1.0 M HCl solution was first investigated by weight loss, potentiodynamic polarization, ultraviolet and visible spectrophotometer (UV-vis), X-ray photoelectron spectroscopy (XPS) and atomic force microscope (AFM). The results revealed that vanillin had a moderate inhibitive effect, and the adsorption of vanillin obeyed the Temkin adsorption isotherm. For rare earth Ce{sup 4+}, it had a negligible effect. However, incorporation of Ce{sup 4+} with vanillin significantly improved the inhibition performance, and produced strong synergistic inhibition effect. Depending on the results, the synergism mechanism was proposed.

  2. Paradoxical bronchospasm from benzalkonium chloride (BAC) preservative in albuterol nebulizer solution in a patient with acute severe asthma. A case report and literature review of airway effects of BAC.

    Science.gov (United States)

    George, Mathew; Joshi, Saumya Vinod; Concepcion, Emily; Lee, Haesoon

    2017-01-01

    Nebulized bronchodilator solutions are available in the United States as both nonsterile and sterile-filled products. Sulfites, benzalkonium chloride (BAC), or chlorobutanol are added to nonsterile products to prevent bacterial growth. Bronchoconstriction from inhaled BAC is cumulative, prolonged, and correlates directly with basal airway responsiveness. The multi-dose dropper bottle of albuterol sulfate solution contains 50 μg BAC per/2.5 mg of albuterol, which may be below or at the lower limit of the threshold dose for bronchoconstriction. However, with repeated albuterol nebulization, the effect can be additive and cumulative, often exceeding the bronchoconstriction threshold. We report a case of a 17 years old patient, who received 32 mg of BAC via nebulization over a period of 3.5 days that probably caused persistent bronchospasm evidenced by failure to improve clinically and to increase peak expiratory flow rate (PEFR) from 125 L/min (27% of predicted value) to 300 L/min (68% of predicted value) within 2 hours of withdrawing BAC. The patient's respiratory status and PEFR improved dramatically once the nebulization solution was switched to BAC free lev-albuterol solution. The pediatric providers, particularly the emergency department physicians, intensivists and pulmonologists need to be aware of this rare albeit possible toxicity to the respiratory system caused by BAC used as a preservative in albuterol nebulizer solution.

  3. Paradoxical bronchospasm from benzalkonium chloride (BAC preservative in albuterol nebulizer solution in a patient with acute severe asthma. A case report and literature review of airway effects of BAC

    Directory of Open Access Journals (Sweden)

    Mathew George, MD

    2017-01-01

    Full Text Available Nebulized bronchodilator solutions are available in the United States as both nonsterile and sterile-filled products. Sulfites, benzalkonium chloride (BAC, or chlorobutanol are added to nonsterile products to prevent bacterial growth. Bronchoconstriction from inhaled BAC is cumulative, prolonged, and correlates directly with basal airway responsiveness. The multi-dose dropper bottle of albuterol sulfate solution contains 50 μg BAC per/2.5 mg of albuterol, which may be below or at the lower limit of the threshold dose for bronchoconstriction. However, with repeated albuterol nebulization, the effect can be additive and cumulative, often exceeding the bronchoconstriction threshold. We report a case of a 17 years old patient, who received 32 mg of BAC via nebulization over a period of 3.5 days that probably caused persistent bronchospasm evidenced by failure to improve clinically and to increase peak expiratory flow rate (PEFR from 125 L/min (27% of predicted value to 300 L/min (68% of predicted value within 2 hours of withdrawing BAC. The patient's respiratory status and PEFR improved dramatically once the nebulization solution was switched to BAC free lev-albuterol solution. The pediatric providers, particularly the emergency department physicians, intensivists and pulmonologists need to be aware of this rare albeit possible toxicity to the respiratory system caused by BAC used as a preservative in albuterol nebulizer solution.

  4. EU FP7 EREAN training network offers (c)lean recycling solutions for rare-earth magnets

    OpenAIRE

    2015-01-01

    EREAN is the European Rare Earth Magnet Recycling Network which started its activities in September 2013. It trains 15 young researchers in the direct and indirect recycling of NdFeB permanent magnets. The innovative aspect of the EREAN project is that it addresses the whole materials loop from End-of-Life consumer goods to recycling and the production of new REE magnets, with an integrated life cycle assessment. As is highlighted by the European Rare Earths Competency Network (ERECON),...

  5. EU FP7 EREAN training network offers (c)lean recycling solutions for rare-earth magnets

    OpenAIRE

    Binnemans, Koen; Jones, Peter Tom

    2015-01-01

    EREAN is the European Rare Earth Magnet Recycling Network which started its activities in September 2013. It trains 15 young researchers in the direct and indirect recycling of NdFeB permanent magnets. The innovative aspect of the EREAN project is that it addresses the whole materials loop from End-of-Life consumer goods to recycling and the production of new REE magnets, with an integrated life cycle assessment. As is highlighted by the European Rare Earths Competency Network (ERECON),...

  6. Diluting ferric carboxymaltose in sodium chloride infusion solution (0.9% w/v) in polypropylene bottles and bags: effects on chemical stability

    OpenAIRE

    Philipp, Erik; Braitsch, Michaela; Bichsel, Tobias; Mühlebach, Stefan

    2015-01-01

    Objectives This study was designed to assess the physicochemical stability of colloidal ferric carboxymaltose solution (Ferinject) when diluted and stored in polypropylene (PP) bottles and bags for infusion. Methods Two batches of ferric carboxymaltose solution (Ferinject) were diluted (500 mg, 200 mg and 100 mg iron in 100 mL saline) in PP bottles or bags under aseptic conditions. The diluted solutions were stored at 30°C and 75%±5% relative humidity (rH) for 72 h, and samples were withdrawn...

  7. Formation of an Ion-Pair Molecule with a Single NH+...Cl- Hydrogen Bond: Raman spectra of 1,1,3,3-Tetramethylguanidinium chloride in the solid state, in solution and in the vapor phase

    DEFF Research Database (Denmark)

    Berg, Rolf W.; Riisager, Anders; Fehrmann, Rasmus

    2008-01-01

    Some ionic compounds (salts) form liquids when heated to temperatures in the range of 200-300 °C. They may be referred to as moderate temperature ionic liquids. An example of such a compound is the 1,1,3,3- tetramethylguanidinium chloride, [TMGH]Cl, melting at ∼212 °C. The chemistry...... scattering spectra are presented and assigned, by comparing to the quantum mechanical calculations. It is concluded that dimeric molecular ion pairs with four N-H+ · · · Cl- hydrogen bonds probably exist in the solutions and are responsible for the relatively high solubility of the “salt” in ethanol......- hydrogen bond, the stretching band of which is causing the band....

  8. New Data on Activity Coefficients of Potassium, Nitrate, and Chloride Ions in Aqueous Solutions of KNO3 and KCl by Ion Selective Electrodes

    OpenAIRE

    Debasmita Dash; Shekhar Kumar; C. Mallika; U. Kamachi Mudali

    2012-01-01

    Ion selective electrodes (ISEs) are used to measure the single-ion activity coefficients in aqueous solutions of KNO3 and KCl at 298.15 K against a double-junction reference electrode. The EMF responses of ISEs up to 0.01 m are plotted to obtain the slope and intercept values. The obtained slopes and intercepts are used in Nernst equation for higher concentrated solutions for calculation of individual ion activity coefficient. The mean ionic activity coefficients are estimated from single ion...

  9. Ionisation and dissociation of diarylmethyl chlorides in BCl/sub 3/CH/sub 2/Cl/sub 2/ solution: Spectroscopic evidence for carbenium ion pairs

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, R.; Mayr, H.; Plesch, P.H.

    1987-12-01

    The ionisation equilibria of diarylmethyl chlorides Ar/sub 2/CHCl (Ar = p-CH/sub 3/O-C/sub 6/H/sub 4/, p-PhO-C/sub 6/H/sub 4/, p-CH/sub 3/-C/sub 6/H/sub 4/) reacting with BCl/sub 3/ in CH/sub 2/Cl/sub 2/ to give ion-pairs Ar/sub 2/CH/sup +/BCl/sub 4//sup -/ (K/sub 1/), and the dissociation of these (K/sub D/) were studied by conductimetry and spectro-photometry. The molar conductivities are almost independent of the nature of the aryl group (approx. = 3.5.10/sup -3/ Sm/sup 2/mol at -70/sup 0/C). The ionisation constants K/sub I/ increase strongly with increasing electron releasing ability of the p-substituents. The standard ionisation enthalpies and entropies for (p-CH/sub 3/-C/sub 6/H/sub 4/)/sub 2/CHCl and (p-PhO-C/sub 6/H/sub 4/)(Ph)CHCl, calculated from the K/sub I/ at different temperatures are negative. The dissociation constants K/sub D/ ((1.9-2.9).10/sup -4/ molL at -70/sup 0/C) do not show a systematic dependence on the electron donating abilities of the substituents in the aryl groups. Small differences between the UV-vis absorption spectra of unpaired and paired ions were used to confirm the conductimetrically determined values of K/sub D/.

  10. Chloride Transport in Undersea Concrete Tunnel

    Directory of Open Access Journals (Sweden)

    Yuanzhu Zhang

    2016-01-01

    Full Text Available Based on water penetration in unsaturated concrete of underwater tunnel, a diffusion-advection theoretical model of chloride in undersea concrete tunnel was proposed. The basic parameters including porosity, saturated hydraulic conductivity, chloride diffusion coefficient, initial water saturation, and moisture retention function of concrete specimens with two water-binder ratios were determined through lab-scale experiments. The variation of chloride concentration with pressuring time, location, solution concentration, initial saturation, hydraulic pressure, and water-binder ratio was investigated through chloride transport tests under external water pressure. In addition, the change and distribution of chloride concentration of isothermal horizontal flow were numerically analyzed using TOUGH2 software. The results show that chloride transport in unsaturated concrete under external water pressure is a combined effect of diffusion and advection instead of diffusion. Chloride concentration increased with increasing solution concentration for diffusion and increased with an increase in water pressure and a decrease in initial saturation for advection. The dominant driving force converted with time and saturation. When predicting the service life of undersea concrete tunnel, it is suggested that advection is taken into consideration; otherwise the durability tends to be unsafe.

  11. Chloride Ingress into Concrete under Water Pressure

    OpenAIRE

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent; Hansen, Kurt Kielsgaard

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 kPa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly infl...

  12. Experimental determination and chemical modelling of radiolytic processes at the spent fuel/water interface. Experiments carried out in carbonate solutions in absence and presence of chloride

    Energy Technology Data Exchange (ETDEWEB)

    Bruno, Jordi; Cera, Esther; Grive, Mireia; Duro, Lara [Enviros Spain SL (Spain); Eriksen, Trygve [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear Chemistry

    2003-01-01

    We report on the recent experimental and modelling results of a research programme that started in 1995. The aim has been to understand the kinetic and thermodynamic processes that control the radiolytic generation of oxidants and reductants at the spent fuel water interface and their consequences for spent fuel matrix stability and radionuclide release. This has been done by carrying out well-controlled dissolution experiments of PWR Ringhals spent fuel fragments in an initially anoxic closed system and by using different solution compositions. Experimental series started with several tests carried out with deionised water as solvent, in a second phase experiments were conducted with 10 mM bicarbonate solutions. New experimental series were set up during the last two years by using the same bicarbonate content in solutions with varying NaCl concentrations in order to ascertain the role of this ligand on the radiolytic products and its consequence for radionuclide release. The selected NaCl concentrations are in the range of 0.1 to 10 mM. Experimental data shows that uranium dissolution at early contact times is controlled by the oxidation of the UO{sub 2} matrix. This process controls the co-dissolution of most of the analysed radionuclides, including Sr, Mo, Tc, Np and surprisingly enough, Cs. In the overall the release rates for U and the matrix associated radionuclides are in the range of 10{sup -6} moles/day with a clear decreasing trend with exposure time and after 2 years the initial release rates have decreased down to 3x10{sup -8} moles/day. The solubility of the released actinides appears to be limited by the formation of An(IV) hydroxide phases, although Np concentrations in solution did not reach solubility levels during the time intervals of the present tests. No secondary solid phase appears to control the solubility of the rest of the elements.

  13. Direct transformation of calcium sulfite to {alpha}-calcium sulfate hemihydrate in a concentrated Ca-Mg-Mn chloride solution under atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Baohong Guan; Hailu Fu; Jie Yu; Guangming Jiang; Bao Kong; Zhongbiao Wu [Zhejiang University, Hangzhou (China). Department of Environmental Engineering

    2011-01-15

    Massive quantities of sulfite-rich flue gas desulfurization (FGD) scrubber sludge have been generated by coal burning power plants. Utilization of the sulfite-rich sludge for preparing {alpha}-calcium sulfate hemihydrate ({alpha}-HH), an important kind of cementitious material, is of particular interest to electric utilities and environmental preservation. In the experiment, calcium sulfite hemihydrate was directly transformed to {alpha}-HH without the occurrence of calcium sulfate dihydrate (DH). The transformation was performed in a concentrated CaCl{sub 2} solution containing Mg{sup 2+} and Mn{sup 2+} at 95{sup o}C, atmospheric pressure and low pH. The oxidation of calcium sulfite and the subsequent crystallization of {alpha}-HH constitute the whole conversion, during which the oxidation turns out to be the rate controlling step. Solid solution comprised of calcium sulfite hemihydrate and calcium sulfate was found to coexist with {alpha}-HH in the suspension. Calcium sulfate increases and calcium sulfite decreases spontaneously until the solid solution disappears. Thus, it is a potential alternative to utilize sulfite-rich FGD scrubber sludge for the direct preparation of {alpha}-HH. 36 refs., 10 figs., 1 tab.

  14. Separation characteristics of rare earth elements in the TOPO/DTPA - Salting-out reagent solution system

    Energy Technology Data Exchange (ETDEWEB)

    Miyahara, S.; Koma, Yoshikazu; Koyama, Tomozo; Tanaka, Yasumasa [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan). Tokai Works; Kano, J.

    1998-11-01

    A test of mutual separation of rare earth elements was carried out using an organic phosphorus extraction solvent TOPO (tri-octyl phosphorus oxide). It was found that the distribution ratio monotonously increased with the atomic number and the separation factor of La/Ln was 10{sup 3}. Under the condition that a sufficient quantity of DTPA compared with the amount of rare earth metals and pH > 1.5 in which DTPA easily formed complexes with lanthanides, the following conclusions were obtained; (i) the separation factor was not affected by pH, the kind of salting-out reagent, or the concentration, (ii) the extraction reaction with TOPO and complex formation with DTPA mainly contributed to the separation of lanthanides, and (iii) the separation factor computed by means of the distribution ratio of TOPO extraction and complex formation constant for DTPA more or less agreed with the empirical value. Separation of rare earth elements using TOPO revealed similar characteristics to those of systems with CMPO and TBP. (H. Baba)

  15. Determination of benzalkonium chloride in ambroxol hydrochloride inhalation solution by RP-HPLC%反相液相色谱法测定盐酸氨溴素吸入溶液中苯扎氯铵的含量

    Institute of Scientific and Technical Information of China (English)

    卜宇倩; 蒋宇丹; 邵佶祥

    2015-01-01

    目的:建立盐酸氨溴素吸入溶液中苯扎氯铵含量的反相液相色谱测定方法。方法:采用Agilent Zorbax SB-C18色谱柱(4.6 mm×250 mm,5mm);以0.02 mol/L庚烷磺酸钠(含0.1%三乙胺,用磷酸调节pH至3.0±0.1)-乙腈(35∶65)为流动相;检测波长208 nm;进样体积20ml。结果:苯扎氯铵浓度在3.32~7.74mg/ml范围内线性关系良好,平均回收率为99.2%。结论:该方法快速、简便、准确、专属性强、重复性好,可适用于盐酸氨溴索吸入溶液中苯扎氯铵的含量测定。%Objective:To establish a RP-HPLC method for the quantitative analysis of benzalkonium chloride in ambroxol hydrochloride inhalation solution.Methods: RP-HPLC was performed on a column of an Agilent Zorbax SB- C18 (4.6 mm × 250 mm,5mm) with a mobile phase of 0.02 mol/L sodium 1-heptanesulfate solution (containing 0.1% triethylamine, adjusted pH to 3.0±0.1 by phosphate)-acetonitrile (35∶65) and at UV detection wavelength of 208 nm. Results:The standard curve was linear over the range of 3.32~7.74mg/ml with the average recovery 99.2% (n=9).Conclusion:This method is fast, simple, accurate, sensitive with good reproducibility and can be applied in the determination of benzalkonium chloride in ambroxol hydrochloride inhalation solution.

  16. Mechanosynthesis and mechanolysis of solid solutions of La{sub 2}O{sub 3} with some rare earth oxides

    Energy Technology Data Exchange (ETDEWEB)

    Todorowsky, D. [Sofia Univ. (Bulgaria). Khimicheski Fakultet; Terziev, A. [Sofia Univ. (Bulgaria). Khimicheski Fakultet; Minkova, N. [Sofia Univ. (Bulgaria). Khimicheski Fakultet

    1996-12-31

    The effect of the mechanoactivation on Y{sub 2}O{sub 3}, Nd{sub 2}O{sub 3} and CeO{sub 2}, on mixtures of La{sub 2}O{sub 3} with each of these oxides as well as on the solid solutions La{sub 2}O{sub 3}-CeO{sub 2} is studied. The activation causes a decrease of the individual oxides` unit cell parameters. The formation of solid solutions of La{sub 2}O{sub 3} with the oxides studied is found. Under the conditions of activation in air no decomposition of La{sub 2}O{sub 3}-CeO{sub 2} solid solution is detected. The solution is, however, destroyed when the activation is carried out in the presence of acids. (orig.)

  17. Hydrogen Production from Water by Photolysis, Sonolysis and Sonophotolysis with Solid Solutions of Rare Earth, Gallium and Indium Oxides as Heterogeneous Catalysts

    Directory of Open Access Journals (Sweden)

    Marta Penconi

    2015-07-01

    Full Text Available In this work, we present the hydrogen production by photolysis, sonolysis and sonophotolysis of water in the presence of newly synthesized solid solutions of rare earth, gallium and indium oxides playing as catalysts. From the experiments of photolysis, we found that the best photocatalyst is the solid solution Y0.8Ga0.2InO3 doped by sulphur atoms. In experiments of sonolysis, we optimized the rate of hydrogen production by changing the amount of water, adding ethanol and tuning the power of our piezoelectric transducer. Finally, we performed sonolysis and sonophotolysis experiments in the presence of S:Y0.8Ga0.2InO3 finding a promising synergistic effect of UV-visible electromagnetic waves and 38 kHz ultrasound waves in producing H2.

  18. Corrosion characteristics of Al-Si-Mg/SiC{sub p} composites with varying Si/Mg molar ratio in neutral chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Escalera-Lozano, R.; Pech-Canul, M.I. [Cinvestav Saltillo (Mexico); Pech-Canul, M.A.; Quintana, P. [Departamento de Fisica Aplicada, Merida, Yuc. (Mexico)

    2009-09-15

    The corrosion resistance of Al-Mg-Si/SiC{sub p} composites produced by the pressureless infiltration method [using SiC{sub p} preforms with 50% porosity containing rice hull ash (RHA) and four custom-made alloys with varying Si/Mg molar ratio] was evaluated in neutral 0.1 M NaCl solutions. The deleterious phase Al{sub 4}C{sub 3} was successfully suppressed in composites with Si/Mg molar ratios of 0.89 and 1.05, but not in those with lower Si/Mg molar ratios (0.12 and 0.49). Results of cyclic polarizations in deareated 0.1 M NaCl solutions showed that with increasing Si/Mg molar ratio, passive current density increased but pitting susceptibility decreased both for reinforced and unreinforced alloys. Immersion tests in aerated 0.1 M NaCl showed that for composites with Si/Mg molar ratios of 0.12 and 0.49 chemical degradation by hydrolysis of Al{sub 4}C{sub 3} was followed by intense anodic dissolution at the matrix-reinforcement interface, while composites corresponding to Si/Mg molar ratios of 0.89 and 1.05 did not exhibit intense localized attack. Possible reasons for the improvement in resistance to localized corrosion are discussed. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  19. 挡土墙被动土压力的滑移线解%Slip-line solution to passive earth pressure on retaining walls

    Institute of Scientific and Technical Information of China (English)

    彭明祥

    2011-01-01

    Based on the limit equilibrium theory, the backfill is treated as a perfectly elastic-plastic material which follows the Mohr-Coulomb yield criterion, and is assumed to be an isotropic, homogeneous and incompressible (or non-expansive) perfectly continuous medium.The stress singularity and its stress boundary condition are introduced, and' a statically determinate and solvable mathematical model for the limit equilibrium boundary value problem is established without considering the stress-strain relationship.Then the slip-line field and stress field in plastic zone of the backfill are solved by use of the slip-line method, furthermore, the passive earth pressure on retaining walls and the reaction on slip surfaces are derived.Geometric and mechanical similarity principle is presented by means of dimensionless analysis.The results show that the slip-line solution to the passive earth pressure is generally less than or equal to the Coulomb's solution, and the classical Rankine's earth pressure or the classical Coulomb's earth pressure satisfying non-singularity condition is in accordance with the slip-line solution, and the Hencky's first theorem and second theorem are not generally applicable.%基于极限平衡理论,视墙后填土为服从Mohr-Coulomb屈服准则的理想弹塑性材料,并且假定它是各向同性的、均匀的以及不可压缩(膨胀)的理想连续介质.引进了应力奇点及其应力边界条件,建立了静定可解的极限平衡边值问题数学模型,而不必考虑土的应力-应变关系,采用滑移线法求解了墙后塑性区的滑移线场和应力场,进而求解了挡土墙被动土压力和滑裂面土反力.通过无量纲分析,提出了几何力学相似原理.数值分析表明,被动土压力的滑移线解一般总是小于或等于库仑解,经典朗肯土压力或满足非奇异条件的经典库仑土压力与滑移线解一致,Hencky第一定理和第二定理不具有普遍适用性.

  20. Calculation of Interaction Parameters from Immiscible Phase Diagram of Alkali Metal or Alkali Earth Metal-Halide System by Means of Subregular Solution Model

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper, the interaction parameters in the subregular solution model, λ1 and λ2, are regarded as a linear function of temperature, T. Therefore, the molar excess Gibbs energy of A-B binary system may be reexpressed as follows: The calculation of the model parameters, λ11, λ12, λ21 and λ22, was carried out numerically from the phase diagrams for 11 alkali metal-alkali halide or alkali earth metal-halide systems.In addition, artificial neural network trained by known data has been used to predict the values of these model parameters. The predicted results are in good agreement with the.calculated ones. The applicability of the subregular solution model to the alkali metal-alkali halide or alkali earth metal-halide systems were tested by comparing the available experimental composition along the boundary of miscibility gap with the calculated ones which were obtained by using genetic algorithm. The good agreement between the calculated and experimental results across the entire liquidus is valid evidence in support of the model.

  1. Hybrid silica nanoparticles for sequestration and luminescence detection of trivalent rare-earth ions (Dy{sup 3+} and Nd{sup 3+}) in solution

    Energy Technology Data Exchange (ETDEWEB)

    Topel, Seda Demirel; Legaria, Elizabeth Polido [Swedish University of Agricultural Sciences (SLU), Department of Chemistry (Sweden); Tiseanu, Carmen [National Institute for Laser, Plasma and Radiation Physics (Romania); Rocha, João [University of Aveiro, Department of Chemistry CICECO (Portugal); Nedelec, Jean-Marie [Clermont Université, ENSCCF, Institute de Chimie de Clermont-Ferrand (France); Kessler, Vadim G.; Seisenbaeva, Gulaim A., E-mail: gulaim.seisenbaeva@slu.se [Swedish University of Agricultural Sciences (SLU), Department of Chemistry (Sweden)

    2014-12-15

    New hybrid material-based adsorbents acting also as luminescent probes upon uptake of trivalent rare-earth (RE) ions Nd{sup 3+} and Dy{sup 3+} have been developed. SiO{sub 2} NPs functionalized by three different organic ligands, N-aminopropylen-amido-iminodiacetic acid (L1), pyridine-α,β-dicarboxylic acid bis(propylenamide) (L2), and N-propylen-iminodiacetic acid (L3), have been produced and fully characterized by {sup 13}C, {sup 1}H, and {sup 29}Si solid-state NMR, FTIR, TGA, XRD, TEM, nitrogen gas adsorption, and also by NTA and DLS in solution. The synthesized hybrid materials are well dispersible and stable in aqueous solutions according to NTA and consist of spheres with diameters less than 100 nm. Their affinities to the lanthanide ions Dy{sup 3+} and Nd{sup 3+} have been investigated in aqueous solution and characterized by SEM–EDS and complexometric titration, demonstrating that they can be successfully used as adsorbents for sequestration of trivalent RE ions. The adsorbed RE ions can efficiently be desorbed from saturated nanoadsorbents by addition of hydrochloric acid. The produced nanomaterials may also be used as luminescent probes for Dy{sup 3+} and Nd{sup 3+} ions in solution.

  2. Hydroxyethyl cellulose as efficient organic inhibitor of zinc-carbon battery corrosion in ammonium chloride solution: Electrochemical and surface morphology studies

    Science.gov (United States)

    Deyab, M. A.

    2015-04-01

    Hydroxyethyl cellulose (HEC) has been investigated as corrosion inhibitor for zinc-carbon battery by polarization and electrochemical impedance spectroscopy (EIS) measurements. The obtained results show that the maximum inhibition efficiency by HEC in 26% NH4Cl solution at 300 ppm and 298 K is 92.07%. Tafel polarization studies reveal that HEC acts as an efficient mixed inhibitor. The corrosion rate is suppressed by the adsorption of HEC on the zinc surface. HEC adsorption obeys the Langmuir isotherm and the thermodynamic parameters Kads and Δ Gadso have been also calculated and discussed. Both physisorption and chemisorption may occur on the zinc surface. Surface characterization investigation using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) is used to ascertain the nature of the protective film.

  3. The electrochemical behaviors of Mg-8Li-3Al-0.5Zn and Mg-8Li-3Al-1.0Zn in sodium chloride solution

    Science.gov (United States)

    Lv, Yanzhuo; Liu, Min; Xu, Yan; Cao, Dianxue; Feng, Jing

    2013-03-01

    The electrochemical oxidation behaviors of Mg-8Li-3Al-0.5Zn and Mg-8Li-3Al-1.0Zn electrodes in 0.7 mol L-1 NaCl solution are investigated by methods of potentiodynamic polarization, potentiostatic oxidation, electrochemical impedance spectroscopy and scanning electron microscopy. The phase composition of Mg-8Li-3Al-0.5Zn and Mg-8Li-3Al-1.0Zn alloys is analyzed conducted by X-ray diffraction. The performances of Mg-8Li-3Al-0.5Zn and Mg-8Li-3Al-1.0Zn as the anode of Mg-H2O2 semi fuel cells are determined. The effect of Zn content on the corrosion resistant of these Mg-Li-based alloys is studied. It is found that the Mg-8Li-3Al-0.5Zn electrode has higher discharge activity and less corrosion resistance than that of Mg-8Li-3Al-1.0Zn electrode in 0.7 mol L-1 NaCl solution. The Mg-H2O2 semi fuel cell with Mg-8Li-3Al-0.5Zn anode presents a maximum power density of 100 mW cm-2 at room temperature, which is higher than that of Mg-8Li-3Al-1.0Zn anode (80 mW cm-2). The performance of semi fuel cell with the Mg-8Li-3Al-0.5Zn electrode is better than that with Mg-8Li-3Al-1.0Zn electrode, especially at higher current density (>30 mA cm-2).

  4. HPLC法测定磷酸钠盐灌肠液中防腐剂苯扎氯铵的含量%Deternination of Preservative Benzalkonium Chloride in Sodium Phos-phate Rectal Solution by HPLC

    Institute of Scientific and Technical Information of China (English)

    傅素华; 叶兴法; 韩鹏; 田利洪

    2015-01-01

    目的:建立测定磷酸钠盐灌肠液中防腐剂苯扎氯铵的含量。方法采用高效液相色谱法。色谱柱为 Ultimate AQ-C18柱(5μm,4.6×250mm);流动相:乙腈-5mmoL醋酸铵溶液(含1%三乙胺,用冰醋酸调节pH值至5.0±0.5)(65∶35);流速:1.0mL· min -1;柱温:35℃;检测波长214nm。结果苯扎氯铵n-C12H25取代同系物在0.1839μg~0.5517μg范围内线性关系良好。(r=0.9999,n =5);平均回收率为100.5%, RSD为1.45%(n=9)。结论该方法简便快速,结果准确,可用于测定磷酸钠盐灌肠液中防腐剂苯扎氯铵的含量。%OBJECTIVE To establish a method for the the Deternination of preservative benzalkonium chloride in Sodium Phosphate Rectal Solution.METHODS HPLC, Liquid chromatography column was Ultimate AQ-C18 (5μm,4.6 ×250mm);mobile phase was acetonitrile-5mmol· L-1 ammonium acetate solution (Containing 1%three triethylamine;dilute Glacial aceticacld pH 5.0 ±0.5 ) ( 65∶35 );flow rate was 1.0 mL · min-1;column temperature was 35℃;detection wavelength was 214 nm.RESULTS The calibration curve of n-C12 H2 5 substituted congeners in benzalkonium chloride was linear in the sample volume range of 0.1839μg~0.5517μg ( r=0.9999 ).The average recovery was 100.5%(RSD=1.45%,n=9).CONCLUSION The method is simple,rapid and accurate,can be the product quality control methods.

  5. D2EHPA对高浓度盐酸介质中钛的萃取%Solvent extraction of tetravalent thitanium from high concentration of acidic chloride solutions by D2EHPA

    Institute of Scientific and Technical Information of China (English)

    毛雪华; 刘代俊

    2012-01-01

    研究了D2 EHPA对盐酸介质中钛的萃取和反萃性能.研究结果表明:萃取液中钛以TiOCl2·2 D2 EHPA的形式存在.钛萃取率随无机相中氯离子浓度和有机相中萃取剂浓度的增加而增加.D2EHPA对钛的饱和承载量为8.98 g/100 g D2EHPA.红外光谱研究进一步表明了Ti-D2EHPA螯合物的性质.在0.5-12 moL/dm3的盐酸介质中,D2EHPA对钛的萃取率随盐酸介质浓度的增加而增加,而对铁、铝、钙、镁无萃取性能.以7% H2O2 +3 mol/dm3 H2SO4为反萃剂,有机相中的钛可实现一次完全反萃.%The solvent extraction and stripping of titanium(IV) from acidic chloride solutions by D2EHPA(di-2-ethylhexyl phosphoric acid) in kerosene has been investigated. The solvent extraction results show that the dissolved titanium is present as TiOCl2 ·D2EHPA. The extractability of titanium ( IV ) increases with the increase of the total chloride concentration in the aqueous phase and the extractant concentration in the organic phase. The loading capacity of D2EHPA for titanium( IV) is 8. 98 g/100 g D2EHPA. IR spectroscopy is used to study the extracted complex in order to further clarify the nature of extracted complex. The results show that,the extractability of titanium( IV) increases when the concentration of hydrochloric acid aqueous solution increases from 0.5 mol'dm" to 12 mol o dm . On the other hand, iron ( III) , aluminum ( HI) , calcium ( II ) and magnesium ( II ) are not extracted under the same experimental conditions. Titanium( IV) can be completely stripped from the metal loaded organic phase with 7% H2O2 in 3 mol-dm H2SO4 as the stripping agent.

  6. SOLUTIONING

    Directory of Open Access Journals (Sweden)

    Maria de Hoyos Guajardo, Ph.D. Candidate, M.Sc., B.Eng.

    2004-11-01

    Full Text Available The theory that is presented below aims to conceptualise how a group of undergraduate students tackle non-routine mathematical problems during a problem-solving course. The aim of the course is to allow students to experience mathematics as a creative process and to reflect on their own experience. During the course, students are required to produce a written ‘rubric’ of their work, i.e., to document their thoughts as they occur as well as their emotionsduring the process. These ‘rubrics’ were used as the main source of data.Students’ problem-solving processes can be explained as a three-stage process that has been called ‘solutioning’. This process is presented in the six sections below. The first three refer to a common area of concern that can be called‘generating knowledge’. In this way, generating knowledge also includes issues related to ‘key ideas’ and ‘gaining understanding’. The third and the fourth sections refer to ‘generating’ and ‘validating a solution’, respectively. Finally, once solutions are generated and validated, students usually try to improve them further before presenting them as final results. Thus, the last section deals with‘improving a solution’. Although not all students go through all of the stages, it may be said that ‘solutioning’ considers students’ main concerns as they tackle non-routine mathematical problems.

  7. Is sodium chloride worth its salt?

    Science.gov (United States)

    McIntosh, Euan; Andrews, Peter J

    2013-06-11

    The choice of fluid for resuscitation of the brain-injured patient remains controversial, and the 'ideal' resuscitation fluid has yet to be identified. Large volumes of hypotonic solutions must be avoided because of the risk of cerebral swelling and intracranial hypertension. Traditionally, 0.9% sodium chloride has been used in patients at risk of intracranial hypertension, but there is increasing recognition that 0.9% saline is not without its problems. Roquilly and colleagues show a reduction in the development of hyperchloremic acidosis in brain-injured patients given 'balanced' solutions for maintenance and resuscitation compared with 0.9% sodium chloride. In this commentary, we explore the idea that we should move away from 0.9% sodium chloride in favor of a more 'physiological' solution.

  8. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...

  9. Investigating and Modeling the Thermo-dynamic Impact of Electrolyte Solutions of Sodium Chloride and Sodium Sulfate on Prevention of the Formation of Methane Hydrate

    Directory of Open Access Journals (Sweden)

    M. Manteghian

    2013-07-01

    Full Text Available Devising methods to prevent hydrate formation is of the important issues in natural gas industry. Since a great deal of money is annually spent on using hydrate inhibitors, identification of new inhibitors with higher degrees of efficacy is economically justifiable. Bearing in mind the significant role of hydrate inhibitors in prevention of natural gas pipelines’ getting blocked, the present study attempts to investigate two compounds of NaCl and Na2SO4 as inhibitors of hydrate methane’s formation so as to respond to “what is the inhibitive thermo-dynamic impact of electrolyte compounds of NaCl and Na2SO4 on the formation of methane hydrate?” To do so, this study not only measures the equilibrium temperature and pressure of methane hydrate formation in the presence of electrolyte solutions of NaCl and Na2SO4 and compares the results obtained with the state lacking such inhibitors, but it also assesses the regression and mathematical modeling are utilized within a basic virtual environment in order to propose a model for prediction of thermo-dynamic equilibrium temperature and pressure of methane hydrate formation.

  10. Chloride Ingress into Concrete under Water Pressure

    DEFF Research Database (Denmark)

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent

    2011-01-01

    Pa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly influences the chloride ingress into the concrete and thereby the life length models for concrete structures.......The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 k...

  11. Treasure of the Past VI: Standard Potential of the Silver-Silver-Chloride Electrode from 0° to 95° C and the Thermodynamic Properties of Dilute Hydrochloric Acid Solutions.

    Science.gov (United States)

    Bates, R G; Bower, V E

    2001-01-01

    From electromotive-force measurements of the cell without liquid junction: [Formula: see text]through the range 0° to 95° C, calculations have been made of (1) the standard potential of the silver-silver-chloride electrode, (2) the activity coefficient of hydrochloric acid in aqueous solutions from m (molality) =0 to m=0.1 and from 0° to 90° C, (3) the relative partial molal heat content of hydrochloric acid, and (4) the relative partial molal heat capacity of hydrochloric acid. The extrapolations were made by the method of least squares with the aid of punch-card techniques. Data from at least 24 cells were analyzed at each temperature, and 81 cells were studied at 25° C. The value of the standard potential was found to be 0.22234 absolute volt at 25° C, and the standard deviation was 0.02 millivolt at 0° C, 0.01 millivolt at 25° C, and 0.09 millivolt at 95° C. The results from 0° to 60° C are compared with earlier determinations of the standard potential and other quantities derived from the electromotive force.

  12. Repassivation Potential of Alloy 22 in Sodium and Calcium Chloride Brines

    Energy Technology Data Exchange (ETDEWEB)

    Rebak, R B; Ilevbare, G O; Carranza, R M

    2007-08-11

    A comprehensive matrix of 60 tests was designed to explore the effect of calcium chloride vs. sodium chloride and the ratio R of nitrate concentration over chloride concentration on the repassivation potential of Alloy 22. Tests were conducted using the cyclic potentiodynamic polarization (CPP) technique at 75 C and at 90 C. Results show that at a ratio R of 0.18 and higher nitrate was able to inhibit the crevice corrosion in Alloy 22 induced by chloride. Current results fail to show in a consistent way a different effect on the repassivation potential of Alloy 22 for calcium chloride solutions than for sodium chloride solutions.

  13. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2009-09-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many coastal areas of Australia, may have perturbed catchment chloride balance conditions for appropriate use in CMB applications. In order to deal with these issues, a high resolution chloride deposition map in the coastal region is needed. In this study, we examined geographic, orographic, and atmospheric factors influencing chloride deposition in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia, using partial correlation and regression analyses. The results indicate that coastal distance, and terrain aspect and slope are two most significant factors controlling chloride deposition. Coastal distance accounts for 65% spatial variability in chloride deposition, with terrain aspect and slope for 8%. The deposition gradient is about 0.08 gm-2 year-1 km-1 as one progresses inland. The results are incorporated into a published de-trended residual kriging approach (ASOADeK to produce a 1 km×1 km resolution annual chloride deposition map and a bulk precipitation chloride concentration map. The average uncertainty of the deposition map is about 30% in the western MLR, and over 50% in the eastern MLR. The maps will form a very useful basis for examining catchment chloride balances for use in the CMB application in the study area.

  14. A general water-based precursor solution approach to deposit earth abundant Cu2ZnSn(S,Se)4 thin film solar cells

    Science.gov (United States)

    Yang, Yanchun; Kang, Xiaojiao; Huang, Lijian; Wei, Song; Pan, Daocheng

    2016-05-01

    Earth abundant Cu2ZnSn(S,Se)4 (CZTSSe) has been considered as one of the most promising thin film solar cell absorber candidates. Here, we develop a facile water-based precursor solution approach for depositing high-efficiency Cu2ZnSn(S,Se)4 thin film solar cells. In this environmentally friendly approach, inexpensive elemental Cu, Zn, Sn and S powders are used as the starting materials and are dissolved in the aqueous solution of thioglycolic acid and methylamine, forming a homogeneous precursor solution for depositing Cu2ZnSnS4 nanocrystal thin film. As-deposited CZTS nanocrystal thin films are selenized to form the large-grain CZTSSe absorber layers. It was found that Na doping plays an important role in the formation of the extremely dense and flat CZTSSe absorber layer, and fill factor can be significantly improved for Na-doped CZTSSe solar cells, which lead to a photoelectric conversion efficiency of 6.96% with an open-circuit voltage of 378 mV, a short current density of 28.17 mA cm-2, and a fill factor of 65.4%.

  15. Preparation of Cu-Al layered double hydroxide intercalated with ethylenediaminetetraacetate by coprecipitation and its uptake of rare earth ions from aqueous solution

    Science.gov (United States)

    Kameda, Tomohito; Hoshi, Kazuaki; Yoshioka, Toshiaki

    2013-03-01

    A Cu-Al layered double hydroxide intercalated with ethylenediaminetetraacetate (edta•Cu-Al LDH) was prepared by the dropwise addition of a Cu-Al nitrate solution to an edta solution at constant pH values of 8.0, 9.0, and 10.0. The edta•Cu-Al LDH had Hedta3- in the interlayer. Furthermore, the preparation at pH 8.0 resulted in the intercalation of Cu(edta)2-. The edta•Cu-Al LDH was found to take up rare earth ions from aqueous solution. The uptake of Sc3+ and Y3+ by edta•Cu-Al LDH was attributed to both the chelating functions of the edta ion in the interlayer and the chemical properties of Cu-Al LDH itself. The uptake of La3+ by edta•Cu-Al LDH was primarily caused by the chelating function of edta ions in the interlayer. The edta ions in the edta•Cu-Al LDH interlayer formed chelate complexes in the order Sc3+ > Y3+ > La3+ due to their relative stabilities, Sc(edta)- > Y(edta)- > La(edta)-. Thus, edta ions retain their chelating function even when intercalated in a Cu-Al LDH interlayer.

  16. Removal of blue 1 dye of aqueous solutions with a modified clay with iron chloride; Remocion de colorante azul 1 de soluciones acuosas con una arcilla modificada con cloruro de hierro

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez H, K. A.

    2012-07-01

    At the present time, several technologies have been proposed to remove dyes from water, adsorption is one of the most feasible methods and adsorbents with different properties, such as activated carbon, zeolites, clays and hydrogels among others. In this work, the sorption behavior of blue 1 dye by a natural clay from a site located in the Center-East of Mexico, and other modified with iron chloride were determined. The materials were characterized by X-ray diffraction to analyze its crystal structure, by scanning electron microscopy and elemental microanalysis of energy dispersive X-ray spectrometry to determine the composition and morphology, and the zero point charges were also determined to know the charge distribution on the surface of the clay. The ph effect, contact time, dye concentration and temperature were the parameters considered in this study. The results showed that clay does not suffer any important changes in its structure after the chemical treatments (modification with ferric chloride and contact with blue 1 solutions). The ph influences lightly the adsorption of the dye with natural clay, but the same effect is not observed in the ferric modified clay among the factor ph 6 and 8. The equilibrium time and the sorption capacity for natural clay were 48 hours and 6.16 mg/g, while for the ferric clay were 24 hours and 14.22 mg/g. Adsorption kinetics results were best adjusted to the pseudo first and pseudo second order models. Adsorption isotherms were best adjusted to the Langmuir model, indicating that both clays have a homogeneous surface. Thermodynamic parameters (E, {Delta}S and {Delta}G and {Delta}H) were calculated for the dye adsorption by the natural clay using data of the adsorption kinetics at temperatures between 20 and 50 C, indicating that the adsorption process is exothermic. For the case of ferric clay, it was not possible to calculate these thermodynamic parameters because the adsorption capacities were similar in the range of

  17. Synergism of Rare Earth Ce(III) Ion with Cysteine against Corrosion of P110 Carbon Steel in 3% NaCl Solutions

    Science.gov (United States)

    Liu, Xia; Yang, Jianshu; Liu, Yongping; Ji, Xiangyun; Lu, Ying; Yuan, Yizhi

    The synergism of CeCl3 (Ce) with cysteine (Cys) on the corrosion of P110 carbon steel in 3% NaCl solutions was investigated by electrochemical methods and surface analysis. The results showed that CeCl3 and cysteine do little to inhibit the corrosion of carbon steel, but the combination of CeCl3 with cysteine has obvious synergistic effect on the corrosion of carbon steel and the corrosion inhibition efficiency was improved significantly. The potentiodynamic polarization curves indicated that the mixture of CeCl3 and cysteine acts as a cathodic inhibitor. Scanning electron microscope (SEM) and Infrared (IR) reflection spectra showed the synergistic inhibition effect was formed by the complexes between rare earth Ce(III) ion and amino acid.

  18. Development and testing of FIDELE: a computer code for finite-difference solution to harmonic magnetic-dipole excitation of an azimuthally symmetric horizontally and radially layered earth

    Energy Technology Data Exchange (ETDEWEB)

    Vittitoe, C.N.

    1981-04-01

    The FORTRAN IV computer code FIDELE simulates the high-frequency electrical logging of a well in which induction and receiving coils are mounted in an instrument sonde immersed in a drilling fluid. The fluid invades layers of surrounding rock in an azimuthally symmetric pattern, superimposing radial layering upon the horizonally layered earth. Maxwell's equations are reduced to a second-order elliptic differential equation for the azimuthal electric-field intensity. The equation is solved at each spatial position where the complex dielectric constant, magnetic permeability, and electrical conductivity have been assigned. Receiver response is given as the complex open-circuit voltage on receiver coils. The logging operation is simulated by a succession of such solutions as the sonde traverses the borehole. Test problems verify consistency with available results for simple geometries. The code's main advantage is its treatment of a two-dimensional earth; its chief disadvantage is the large computer time required for typical problems. Possible code improvements are noted. Use of the computer code is outlined, and tests of most code features are presented.

  19. Stability of Alprostadil in 0.9% Sodium Chloride Stored in Polyvinyl Chloride Containers.

    Science.gov (United States)

    McCluskey, Susan V; Kirkham, Kylian; Munson, Jessica M

    2017-01-01

    The stability of alprostadil diluted in 0.9% sodium chloride stored in polyvinyl chloride (VIAFLEX) containers at refrigerated temperature, protected from light, is reported. Five solutions of alprostadil 11 mcg/mL were prepared in 250 mL 0.9% sodium chloride polyvinyl chloride (PL146) containers. The final concentration of alcohol was 2%. Samples were stored under refrigeration (2°C to 8°C) with protection from light. Two containers were submitted for potency testing and analyzed in duplicate with the stability-indicating high-performance liquid chromatography assay at specific time points over 14 days. Three containers were submitted for pH and visual testing at specific time points over 14 days. Stability was defined as retention of 90% to 110% of initial alprostadil concentration, with maintenance of the original clear, colorless, and visually particulate-free solution. Study results reported retention of 90% to 110% initial alprostadil concentration at all time points through day 10. One sample exceeded 110% potency at day 14. pH values did not change appreciably over the 14 days. There were no color changes or particle formation detected in the solutions over the study period. This study concluded that during refrigerated, light-protected storage in polyvinyl chloride (VIAFLEX) containers, a commercial alcohol-containing alprostadil formulation diluted to 11 mcg/mL with 0.9% sodium chloride 250 mL was stable for 10 days.

  20. A model of the general ocean circulation determined from a joint solution for the Earth's gravity field

    Science.gov (United States)

    Nerem, R. S.; Tapley, B. D.; Shum, C. K.; Yuan, D. N.

    1989-01-01

    If the geoid and the satellite position are known accurately, satellite altimetry can be used to determine the geostrophic velocity of the surface ocean currents. The purpose of this investigation is to simultaneously estimate the sea surface topography, zeta, the model for the gravity field, and the satellite orbit. Satellite tracking data from fourteen satellites were used; along with Seasat and Geosat altimeter data as well as surface gravity data for the solution. The estimated model of zeta compares well at long wavelengths with the hydrographic model of zeta. Covariance studies show that the geoid is separable from zeta up to degree 9, at which point geoid error becomes comparable to the signal of zeta.

  1. Spherical disharmonics in the Earth sciences and the spatial solution: Ridges, hotspots, slabs, geochemistry and tomography correlations

    Science.gov (United States)

    Ray, Terrill W.; Anderson, Don L.

    1994-01-01

    There is increasing use of statistical correlations between geophysical fields and between geochemical and geophysical fields in attempts to understand how the Earth works. Typically, such correlations have been based on spherical harmonic expansions. The expression of functions on the sphere as spherical harmonic series has many pitfalls, especially if the data are nonuniformly and/or sparsely sampled. Many of the difficulties involved in the use of spherical harmonic expansion techniques can be avoided through the use of spatial domain correlations, but this introduces other complications, such as the choice of a sampling lattice. Additionally, many geophysical and geochemical fields fail to satisfy the assumptions of standard statistical significance tests. This is especially problematic when the data values to be correlated with a geophysical field were collected at sample locations which themselves correlate with that field. This paper examines many correlations which have been claimed in the past between geochemistry and mantle tomography and between hotspot, ridge, and slab locations and tomography using both spherical harmonic coefficient correlations and spatial domain correlations. No conclusively significant correlations are found between isotopic geochemistry and mantle tomography. The Crough and Jurdy (short) hotspot location list shows statistically significant correlation with lowermost mantle tomography for degree 2 of the spherical harmonic expansion, but there are no statistically significant correlations in the spatial case. The Vogt (long) hotspot location list does not correlate with tomography anywhere in the mantle using either technique. Both hotspot lists show a strong correlation between hotspot locations and geoid highs when spatially correlated, but no correlations are revealed by spherical harmonic techniques. Ridge locations do not show any statistically significant correlations with tomography, slab locations, or the geoid; the

  2. CHLORIDE WASHER PERFORMACE TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Coughlin, J; David Best, D; Robert Pierce, R

    2007-11-30

    Testing was performed to determine the chloride (Cl-) removal capabilities of the Savannah River National Laboratory (SRNL) designed and built Cl- washing equipment intended for HB-Line installation. The equipment to be deployed was tested using a cerium oxide (CeO2) based simulant in place of the 3013 plutonium oxide (PuO2) material. Two different simulant mixtures were included in this testing -- one having higher Cl- content than the other. The higher Cl- simulant was based on K-Area Interim Surveillance Inspection Program (KIS) material with Cl- content approximately equal to 70,000 ppm. The lower Cl- level simulant was comparable to KIS material containing approximately 8,000-ppm Cl- content. The performance testing results indicate that the washer is capable of reducing the Cl- content of both surrogates to below 200 ppm with three 1/2-liter washes of 0.1M sodium hydroxide (NaOH) solution. Larger wash volumes were used with similar results - all of the prescribed test parameters consistently reduced the Cl- content of the surrogate to a value below 200 ppm Cl- in the final washed surrogate material. The washer uses a 20-micron filter to retain the surrogate solids. Tests showed that 0.16-0.41% of the insoluble fraction of the starting mass passed through the 20-micron filter. The solids retention performance indicates that the fissile masses passing through the 20-micron filter should not exceed the waste acceptance criteria for discard in grout to TRU waste. It is recommended that additional testing be pursued for further verification and optimization purposes. It is likely that wash volumes smaller than those tested could still reduce the Cl- values to acceptable levels. Along with reduced wash volumes, reuse of the third wash volume (in the next run processed) should be tested as a wash solution minimization plan. A 67% reduction in the number of grouted paint pails could be realized if wash solution minimization testing returned acceptable results.

  3. Synergistic inhibition effect of L-phenylalanine and rare earth Ce(IV) ion on the corrosion of copper in hydrochloric acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Daquan, E-mail: zhangdaquan@shiep.edu.cn [Department of Environmental Engineering, Shanghai University of Electric Power, Shanghai 200090 (China); Wu Huan; Gao Lixin [Department of Environmental Engineering, Shanghai University of Electric Power, Shanghai 200090 (China)

    2012-04-16

    Highlights: Black-Right-Pointing-Pointer Synergistic effect of L-phenylalanine (L-Phe) and Ce(SO{sub 4}){sub 2} on the corrosion of copper on the corrosion inhibition of copper in 0.5 M HCl solution. Black-Right-Pointing-Pointer Structure of the complex film formed by the interaction of L-phenylalanine (L-Phe) and Ce(SO{sub 4}){sub 2} on the copper surface. Black-Right-Pointing-Pointer Mechanism of the improvement of the inhibition property of amino acids by the addition of rare earth compound. - Abstract: The synergistic inhibition effect of L-phenylalanine (L-Phe) and Ce(SO{sub 4}){sub 2} on the corrosion of copper in 0.5 M HCl solution was investigated by weight-loss, electrochemical methods and surface analysis. The electrochemical results showed that L-Phe has definite inhibition effects for copper, while Ce(IV) promoted the anodic process of copper corrosion. The combination L-Phe with Ce(IV) ion produced strong synergistic effect on corrosion inhibition for copper. The maximum inhibition efficiency was 82.7% for 5 mM L-Phe + 2 mM Ce(IV). The results of EIS and potentiodynamic polarization are in good agreement. SEM showed that L-Phe and Ce(IV) can form a dense protective film on the copper surface.

  4. Durability of cracked fibre reinforced concrete structures exposed to chlorides

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Ekman, Tom; Hansen, Kurt Kielsgaard

    1999-01-01

    is used as environmental load. The chloride penetration is characterized both qualitatively (UV-test) and quantitatively (chloride profile) and by microscopy. The test programme involves three different concrete qualities. Both steel fibres and polypropylene fibres are used in the concrete beams as well......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to 4-point bending until a predefined crack width is reached, using a newly developed test setup. Exposure to a concentrated chloride solution...... as main reinforcement. The effect of the cracks, the fibres and the concrete quality on the chloride penetration is studied....

  5. Separation Studies of Pd(II from Acidic Chloride Solutions of Pt(IV, Ni(II and Rh(III by Using 4-Aroyl-3-Phenyl-5-Isoxazolones

    Directory of Open Access Journals (Sweden)

    Koduru Janardhan Reddy

    2012-01-01

    Full Text Available This study examined the effect influence of various factors on the extraction of Pd(II to develop a new liquid-liquid extraction mechanism for the selective separation of palladium(II from its acidic chloride solutions using 4-aroyl-3-phenyl-5-isoxazolones (HA, such as 3-phenyl-4-(4-fluorobenzoyl-5- isoxazolone (HFBPI, 3-phenyl-4-benzoyl-5-isoxazolone (HPBI and 3-phenyl-4- (4-toluoyl-5-isoxazolone (HTPI. The extraction strength of Pd(II with HA were in the following order: HFBPI > HPBI > HTPI, which is opposite to that observed with their pKa values. HPBI was used to separate Pd(II from Pt(IV, Ni(II and Rh(III metal ions and calculated their separation factors (S.F. were followed in the order: Pd/Ni (40±0.4 > Pd/Pt (25±0.2 > Pd/Rh (15±0.3 > Rh/Ni (2.7±0.3 > Pt/Ni ≈ Rh/Pt (1.7±0.2. The loading and striping of Pd(II (1.12×10-4 mol L-1 were also examined using 1.0×10-3 mol L-1 HPBI in CHCl3 and 1.0 mol L-1 HCl, respectively. The results demonstrated that the maximum (97.5% extraction and desorption (89% of metal required at least 3.0 cycles. The developed method was applied successfully to the separation of palladium from synthetic water samples.

  6. The recovery of oil from spent bleaching earth

    Energy Technology Data Exchange (ETDEWEB)

    El-Bassuoni, A.A.; Sherief, H.M.; Tayeb, A.M.; Ahmed, K.K. [Minia Univ., Minia (Egypt). Dept. of Chemical Engineering

    2000-07-01

    Four solvent based extraction methods to recover oil from spent bleached earth were presented. Spent bleaching earth is a solid waste that is generated during the processing of vegetable oils. It is removed from the oil with filters and contains approximately 25-29 per cent oil by weight. At the onset of the study, the oil entrained with the spent bleaching earth filtration was determined to be 25 per cent. Four solvents, N-hexane, carbon tetra chloride, benzene and 1,2 dichloroethane were used in this study. The per cent recovery of oil was calculated by measuring the concentration of oil by spectrophotometer. The effect of temperature on the recovery of oil and different solid:liquid ratios was also studied for the four solvents. The following four methods were used for the recovery of oil were solvent extraction, extraction with 1 per cent sodium carbonate solution, extraction with 4.5 per cent sodium dodecyl sulphite solution and boiling with 12 per cent sodium hydroxide solution. All methods gave satisfactory results indicating that the earth could be reused. 12 refs., 3 tabs.

  7. Evaluation of the susceptibility to pitting corrosion of steel api 5L x42 exposed to solutions containing chloride ions and CO{sub 2} by electrochemical noise measurements; Evaluacion de la susceptibilidad a la corrosion por picado del acero api 5l x42 expuesto a un ambiente con cloruros y CO{sub 2} mediante la tecnica de ruido electroquimico

    Energy Technology Data Exchange (ETDEWEB)

    Pena-Ballesteros, D.; Rodriguez-Vanegas, N.; Anteliz, C.; Sarmiento Klapper, H.

    2011-07-01

    The concentration of chloride ions and the partial pressure of CO{sub 2} play an important role in the degradation of low-carbon steels used for the construction of pipelines in oil and gas industry. In order to evaluate the susceptibility of carbon steel API 5L X42 to pitting corrosion electrochemical noise and linear polarization resistance measurements were carried out in aqueous solutions containing chloride ions and CO{sub 2}. The concentration of chloride ions was varied between, 10000 and 18000 ppm, and the CO{sub 2} partial pressure between 10 psi and 18 psi. Experimental results pointed out that the formation of protective layer, consisting mainly of FeCO{sub 3}, depends on the partial pressure of CO{sub 2} in the system. Nevertheless, the stability of this layer was considerably affected by increasing the concentration of chloride ions causing that localized corrosion has taken place in some areas of the surface of API 5L X42, which were detected by electrochemical noise technique. (Author) 10 refs.

  8. The structure and stability of aqueous rare-earth elements in hydrothermal fluids: New results on neodymium(III) aqua and chloroaqua complexes in aqueous solutions to 500 °C and 520 MPa

    Science.gov (United States)

    Mayanovic, Robert A.; Anderson, Alan J.; Bassett, William A.; Chou, I.-Ming

    2009-01-01

    X-ray absorption spectroscopy (XAS) measurements were made at the Nd L3-edge on neodymium(III) aqua and chloroaqua complexes in low pH aqueous solutions from 25 to 500????C and up to 520??MPa. Analysis of the extended X-ray absorption fine structure of the XAS spectra measured from a 0.07??m Nd/0.16??m HNO3 aqueous solution reveals a contraction of the Nd-O distance of the Nd3+ aqua ion at a uniform rate of ~ 0.013????/100????C and a uniform reduction of the number of coordinated H2O molecules from 10.0 ?? 0.9 to 7.4 ?? 0.9 over the range from 25 to 500????C and up to 370??MPa. The rate of reduction of the first-shell water molecules with temperature for Nd3+ (26%) is intermediate between the rate for the Gd3+ aqua ion (22% from 25 to 500????C) and the rates for the Eu3+ (29% from 25 to 400????C) and the Yb3+ aqua ions (42% from 25 to 500????C) indicating an intermediate stability of the Nd3+ aqua ion consistent with the tetrad effect. Nd L3-edge XAS measurements of 0.05??m NdCl3 aqueous solution at 25 to 500????C and up to 520??MPa show that stepwise inner-sphere complexes most likely of the type Nd(H2O)?? - nCln+3 - n occur in the solution at elevated temperatures, where ?? ??? 9 at 150????C decreasing to ~ 6 at 500????C and the number of chloride ions (n) of the chloroaqua complexes increases uniformly with temperature from 1.2 ?? 0.2 to 2.0 ?? 0.2 in the solution upon increase of temperature from 150 to 500????C. Conversely, the number of H2O ligands of Nd(H2O)?? - nCln+3 - n complexes is uniformly reduced with temperature from 7.5 ?? 0.8 to 3.7 ?? 0.3 in the aqueous solution, in the same temperature range. These data show greater stability of neodymium(III) than gadolinium(III) and ytterbium(III) chloride complexes in low pH aqueous solutions at elevated temperatures. Our data suggest a greater stability of aqueous light REE than that of heavy REE chloride complexes in low pH fluids at elevated temperatures consistent with REE analysis of fluids from deep

  9. Carbonisation of coal with chlorides content

    Energy Technology Data Exchange (ETDEWEB)

    E. Plevova

    2002-07-01

    From accessible literature it is evident that the addition of Lewis acids to coal before carbonisation can effect the course of reactions in the way of getting required products. An investigation was carried out into the effects of addition of chloride solutions. For experiments low concentration of solutions of three chlorides (PbCl{sub 2}, ZnCl{sub 2}, AlC{sub 3}) were used. Then samples were carbonised in a special coking retort. Volatile products were collected to establish the mass balance of this process. The resultant properties of obtained char and coal tar were estimated. Evaluation of the solid phase showed the increasing of specific surface although the used solution concentration was quite low. Estimation of obtained tar indicated mainly increasing of aromatic hydrocarbons in consequence of charring and aromatisation of carbon skeleton. 3 refs., 1 fig., 3 tabs.

  10. Enthalpy and entropy interaction parameters of sodium chloride with some monosaccharides in water

    Institute of Scientific and Technical Information of China (English)

    ZHUO; Kelei; WANG; Jianji; BAI; Guangyue; YAN; Haike; WANG

    2004-01-01

    Dilution enthalpies of sodium chloride and some monosaccharides (glucose, galactose, xylose, arabinose, and fructose) in water and mixing enthalpies of aqueous sodium chloride and these monosaccharide solutions were measured by using an improved precision semimicro-titration calorimeter. Transfer enthalpies of sodium chloride from water to aqueous saccharide solutions were evaluated as well as enthalpy interaction parameters of sodium chloride with these monosaccharides in water. Combined with Gibbs energy interaction parameters, entropy interaction parameters were also obtained. The results show that interactions of the saccharides with sodium chloride depend on the stereochemistry of saccharide molecules. These interaction parameters can identify stereochemical structure of saccharide molecules.

  11. An insight into the passivation of cupronickel alloys in chloride environment

    Indian Academy of Sciences (India)

    J Mathiyarasu; N Palaniswamy; V S Muralidharan

    2001-02-01

    Cupronickels offer enhanced corrosion protection in marine environments by the formation of passive films on the surface. Cyclic voltammetric studies were carried on cupronickels in chloride solutions at H 6.3 to understand the role of chloride ions in passive film formation. Increase in nickel content of the alloy and of chloride ions in solution decreases film resistance. Chloride ions take part in reduction of the passive film to copper. A solid-state model for passive film formation involving chloride ions has been attempted.

  12. Removal of ammonia from aqueous solutions by catalytic oxidation with copper-based rare earth composite metal materials: catalytic performance, characterization, and cytotoxicity evaluation

    Institute of Scientific and Technical Information of China (English)

    Chang-Mao Hung

    2011-01-01

    Ammonia (NH3) has an important use in the chemical industry and is widely found in industrial wastewater.For this investigation of copper-based rare earth composite metal materials,aqueous solutions containing 400 mg/L of ammonia were oxidized in a batch-bed reactor with a catalyst prepared by the co-precipitation of copper nitrate,lanthanum nitrate and cerium nitrate.Barely any of the dissolved ammonia was removed by wet oxidation without a catalyst,but about 88% of the ammonia was reduced during wet oxidation over the catalysts at 423 K with an oxygen partial pressure of 4.0 MPa.The catalytic redox behavior was determined by cyclic voltammetry (CV).Furthermore,the catalysts were characterized using thermogravimetric analyzer (TGA) and scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX),which showed that the catalytic behavior was related to the metal oxide properties of the catalyst.In addition,the copper-lanthanum-cerium composite-induced cytotoxicity in the human lung MRC-5 cell line was tested,and the percentage cell survival was determined by 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetra-zolium (MTS) analysis in vitro.No apparent cytotoxicity was observed when the human lung cells were exposed to the copper-lanthanum-cerium composite.

  13. Mechanochemical synthesis, structure, and properties of solid solutions of alkaline earth metal fluorides: Ma1-xMbxF2 (M: Ca, Sr, Ba)

    Science.gov (United States)

    Heise, M.; Scholz, G.; Düvel, A.; Heitjans, P.; Kemnitz, E.

    2016-10-01

    The capability of mechanochemical synthesis for the formation of solid solutions of alkaline earth metal fluorides Ma1-xMbxF2 (M: Ca, Sr, Ba) was tested by fluorination of metal acetates and metal hydroxides with ammonium fluoride directly at milling. Evidence was found for a mutual substitution of cations on their lattice positions in Ca1-xSrxF2 and Ba1-xSrxF2 samples. For the Ba/Ca-system this synthesis route is only partially successful. X-ray diffraction and 19F MAS NMR spectroscopy were used to characterize all samples concerning their crystal structure and local fluorine coordination. Calculations of 19F chemical shifts with the superposition model along with probability calculations for the intensity of the individual 19F lines, performed in dependence on the molar composition of the samples, perfectly agree with the experimental findings. The fluoride ion conductivity of as-prepared samples, determined by temperature dependent DC conductivity measurements, is significantly higher than those of crystalline binary fluorides. Moreover, a higher F- ion conductivity is observed for samples with higher mixing grade in the Ca/Sr-and the Ba/Sr-systems.

  14. Chloride equilibrium potential in salamander cones

    Directory of Open Access Journals (Sweden)

    Bryson Eric J

    2004-12-01

    Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

  15. Modeling Phase Equilibria of Semiclathrate Hydrates Formed with Tetrabutylammonium Chloride Solutions%四丁基氯化铵半笼型水合物的相平衡模型

    Institute of Scientific and Technical Information of China (English)

    史伶俐; 梁德青

    2014-01-01

    Based on the van der Waals-Platteeuw (vdW-P) theory and the hydrate structure of tetrabutylammonium chloride (TBAC), a thermodynamic approach is proposed to determine the phase equilibrium conditions of TBAC semiclathrate hydrates in this work. Two modifications for evaluations of vapor pressure of water in the empty hydrate lattice and Langmuir constants relating to the salt concentration in aqueous solution and temperature are proposed. To obtain the activity coefficients of species in the aqueous phase and the fugacity of gaseous hydrate former in gas phase, the electrolyte-Non-Random Two-Liquid (e-NRTL) activity model and Peng-Robinson equation of state (PR-EoS) are employed, respectively. Additionally, the model predicted phase equilibrium conditions for hydrates of TBAC+CH4 and TBAC+CO2 over temperature, pressure, and salt concentration ranges from 280.1 K to 293.6 K, from 0.337 MPa to 7.017 MPa, and from 4.34% to 34%, respectively. It is shown that agreement of predicted data with experimental data is satisfactory, with average absolute pressure deviation 3.2637%and 9.2258%for hydrates of TBAC+CH4 and TBAC+CO2, respectively.%本文在范德瓦尔-普朗特理论的基础上,考虑了四丁基氯化铵(TBAC)水合物的结构特征,建立了TBAC半笼型水合物相平衡模型。模型确定了水在空水合物晶格的蒸汽压及兰格缪尔常数与 TBAC 浓度的关系,引用e-NRTL模型和PR气体状态方程分别计算液相组分活度系数和客体分子气相逸度。同时,本文在280.1 K~293.6 K温度范围和0.337 MPa~7.017 MPa压力范围内预测了TBAC质量浓度范围为4.34%~34%的溶液体系下TBAC+CH4、TBAC+CO2半笼型水合物的相平衡条件,预测压力与实验数据的平均绝对偏差分别为3.2637%和9.2258%。预测结果与实验数据吻合较好。

  16. Chloride supporting electrolytes for all-vanadium redox flow batteries.

    Science.gov (United States)

    Kim, Soowhan; Vijayakumar, M; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Chen, Feng; Hu, Jianzhi; Li, Liyu; Yang, Zhenguo

    2011-10-28

    This paper examines vanadium chloride solutions as electrolytes for an all-vanadium redox flow battery. The chloride solutions were capable of dissolving more than 2.3 M vanadium at varied valence states and remained stable at 0-50 °C. The improved stability appeared due to the formation of a vanadium dinuclear [V(2)O(3)·4H(2)O](4+) or a dinuclear-chloro complex [V(2)O(3)Cl·3H(2)O](3+) in the solutions over a wide temperature range. The all-vanadium redox flow batteries with the chloride electrolytes demonstrated excellent reversibility and fairly high efficiencies. Only negligible, if any, gas evolution was observed. The improved energy capacity and good performance, along with the ease in heat management, would lead to substantial reduction in capital cost and life-cycle cost, making the vanadium chloride redox flow battery a promising candidate for stationary applications.

  17. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    Directory of Open Access Journals (Sweden)

    Jun Liu

    2014-09-01

    Full Text Available Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions are immersed in NaCl solution with a mass concentration of 5%, to simulate the shallow immersion condition in sea water, and the surface chloride concentrations are measured at different ages. It is found that the surface chloride concentration increases following the increasing immersion durations, and varies from a weight percentage of 0.161%–0.781% in concretes with different mix proportions. The w/c (water-to-cement ratio influences the surface chloride concentration significantly, and the higher the w/c is, the higher the surface chloride concentration will be, at the same age. However, following the prolonging of immersion duration, the difference in surface chloride concentration induced by w/c becomes smaller and smaller. The incorporation of fly ash leads to higher surface chloride concentration. The phenomena are explained based on pore structure analyses.

  18. Amperometric Sensor for Detection of Chloride Ions

    Directory of Open Access Journals (Sweden)

    Rene Kizek

    2008-09-01

    Full Text Available Chloride ion sensing is important in many fields such as clinical diagnosis, environmental monitoring and industrial applications. We have measured chloride ions at a carbon paste electrode (CPE and at a CPE modified with solid AgNO3, a solution of AgNO3 and/or solid silver particles. Detection limits (3 S/N for chloride ions were 100 μM, 100 μM and 10 μM for solid AgNO3, solution of AgNO3 and/or solid silver particles, respectively. The CPE modified with silver particles is the most sensitive to the presence chloride ions. After that we approached to the miniaturization of the whole electrochemical instrument. Measurements were carried out on miniaturized instrument consisting of a potentiostat with dimensions 35 × 166 × 125 mm, screen printed electrodes, a peristaltic pump and a PC with control software. Under the most suitable experimental conditions (Britton-Robinson buffer, pH 1.8 and working electrode potential 550 mV we estimated the limit of detection (3 S/N as 500 nM.

  19. Analytical correlation between varying corrosion parameters and corrosion rate of Al-4.5Cu/10%ZrSiO{sub 4} composite in hydrochloric acid by rare earth chloride

    Energy Technology Data Exchange (ETDEWEB)

    Oloche, O.B.; Yaro, S.A. [Department of Metallurgical Engineering Ahmadu Bello University, Zaria (Nigeria); Okafor, E.G. [Department of Metallurgical Engineering Ahmadu Bello University, Zaria (Nigeria)], E-mail: ekeneokafor@yahoo.com

    2009-03-20

    The effect of varying temperature, time and inhibitor concentration on the corrosion rate of Al-4.5Cu/ZrSiO{sub 4} composite in 0.5 M hydrochloric acid without and with lanthanide chloride salt have been investigated. 10%ZrSiO{sub 4} was used for the production of the Al-4.5Cu/zircon sand composite. The time, temperature and concentration of inhibitor were varied in the range of 6-10 h at 2 h interval, 30-75 deg. C at 15 deg. C interval and 250-1000 ppm at 250 ppm interval respectively. Factorial design, standard deviation, effect of variables at 95% confidence interval and Arrhenius kinetics approach were used to correlate the corrosion parameter and corrosion rate. Results show that increase in temperature, inhibitor concentration above 250 ppm and decrease in time enhance corrosion rate. Also, temperature and anti-corrosion agent concentration are the most important control parameters. The kinetic and statistical approaches were in good agreement.

  20. chloride mass balance

    African Journals Online (AJOL)

    Agadaga

    1Geology Department, Faculty of Sciences and Techniques, University ... characterization of groundwater, rainfall and the unsaturated zone were also carried out using a .... 2008 in collaboration with the Senegal National Meteorological .... [Cl]sm is estimated as average chloride concentration in ..... sands of Australia.

  1. Effects of cyclic chloride exposure on penetration of concrete cover

    Energy Technology Data Exchange (ETDEWEB)

    Hong, K.; Hooton, R.D.

    1999-09-01

    Concretes are in a state of flux between saturated and partially saturated conditions as they undergo continuous cycles of wetting and drying. In saturated concrete, dissolved ions enter through diffusion, whereas in partially saturated concrete, ion-containing fluids are absorbed by capillary suction and concentrated by evaporation of water. The primary focus of this study was to examine the effects of cyclic wetting and drying with sodium chloride solution on chloride ingress into concrete. Chloride profiles of samples exposed to various lengths and numbers of cycles were determined for three mixtures of concrete: two containing slag and/or silica fume with a 0.4 w/cm (water to cementing materials ratio) and one with a 0.3 w/cm. It was found that longer drying times increase the rate of chloride ingress. A good relationship exists between the depth of chloride penetration and the square root of the number of cycles.

  2. Investigation of factors influencing chloride extraction efficiency during electrochemical chloride extraction from reinforcing concrete

    Science.gov (United States)

    Sharp, Stephen R.

    2005-11-01

    Electrochemical chloride extraction (ECE) is an accelerated bridge restoration method similar to cathodic protection, but operates at higher current densities and utilizes a temporary installation. Both techniques prolong the life of a bridge by reducing the corrosion rate of the reinforcing bar when properly applied. ECE achieves this by moving chlorides away from the reinforcement and out of the concrete while simultaneously increasing the alkalinity of the electrolyte near the reinforcing steel. Despite the proven success, significant use of ECE has not resulted in part due to an incomplete understanding in the following areas: (1) An estimation of the additional service life that can be expected following treatment when the treated member is again subjected to chlorides; (2) The cause of the decrease in current flow and, therefore, chloride removal rate during treatment; (3) Influence of water-to-cement (w/c) ratio and cover depth on the time required for treatment. This dissertation covers the research that is connected to the last two areas listed above. To begin examining these issues, plain carbon steel reinforcing bars (rebar) were embedded in portland cement concrete slabs of varying water-to-cement (w/c) ratios and cover depths, and then exposed to chlorides. A fraction of these slabs had sodium chloride added as an admixture, with all of the slabs subjected to cyclical ponding with a saturated solution of sodium chloride. ECE was then used to remove the chlorides from these slabs while making electrical measurements in the different layers between the rebar (cathode) and the titanium mat (anode) to follow the progress of the ECE process. During this study, it was revealed that the resistance of the outer concrete surface layer increases during ECE, inevitably restricting current flow, while the resistance of the underlying concrete decreases or remains constant. During ECE treatment, a white residue formed on the surface of the concrete. Analyses of the

  3. Benzalkonium chloride. Health hazard evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    Bernholc, N.M.

    1984-01-01

    Health hazards associated with the use of benzalkonium chlorides (BAC) are reviewed. Benzalkonium chloride is extensively used as a cationic disinfectant. It is found in a great many over-the-counter and prescription eye products, disinfectants, shampoos, and deodorants, and is used in concentrations that range from 0.001 to 0.01% in eyedrops, up to 2.5% in concentrated liquid disinfectants. Solutions of 0.03 to 0.04% BAC may cause temporary eye irritation in humans but are unlikely to cause any skin response except in persons allergic to quaternary ammonium compounds. Inhalation of a vaporized 10% solution of BAC produced a bronchospasmodic reaction in a previously sensitized individual. At present no other human health effects from BAC have been documented or inferred from exposure to such dilute concentrations.

  4. 焙烧硼钠钙石在高固液化比氯化铵溶液中的熔解动力学%Dissolution Kinetics of Calcined Ulexite in Ammonium Chloride Solutions at High Solid-to-Liquid Ratios

    Institute of Scientific and Technical Information of China (English)

    G(U)R; Aycan

    2006-01-01

    The dissolution kinetics of calcined ulexite in ammonium chloride solutions at high solid-to-liquid ratios were investigated. In the experiments, calcination temperature, solution concentration, reaction temperature, and prehydration were chosen as parameters. It was observed that the dissolution rate increased with increasing calcination temperature, solution concentration, and reaction temperature, whereas it was not affected by pre-hydration. Employing graphical and statistic methods, the dissolution rate, based on homogeneous reaction model,can be given as: (1-X(B2O3))-1-1=k(c(NH4Cl))1.982t. The activation energy for the dissolution of the ulexite sample calcined at 160 ℃ was found to be

  5. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Güler, Ekrem; Olgar, Şeref; Davutoğlu, Mehmet; Garipardıç, Mesut; Karabiber, Hamza

    2011-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is ...

  6. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    OpenAIRE

    Ekrem Güler; Şeref Olgar; Mehmet Davutoğlu; Mesut Garipardıç; Hamza Karabiber

    2014-01-01

    Benzalkonium chloride (BAC) is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is...

  7. Influence of pH and Chloride Concentration on the Corrosion Behavior of Unalloyed Copper in NaCl Solution: A Comparative Study Between the Micro and Macro Scales

    Directory of Open Access Journals (Sweden)

    Annemie Adriaens

    2012-11-01

    Full Text Available The effects of pH and chloride concentration on the electrochemical corrosion of copper in aqueous sodium chloride (NaCl media were studied at the micro scale using a microcapillary droplet cell and at the macro scale using a conventional large scale cell. Using an experimental design strategy, electrochemical response surface models of copper versus pH and NaCl concentration were constructed with the minimum number of experiments required. Results show that the electrochemical behavior of copper under corrosive media shows significant differences between the micro and macro scale experiments. At the micro scale, the pit initiation of copper occurs at more negative potentials for high NaCl concentrations and alkaline pH values. Also, the micro scale potentiostatic measurements indicate higher stabilised passive currents at high NaCl concentrations and low (acidic pH values. At the macro scale, the pH is shown to have a greater influence on the corrosion potential. The chloride concentration is the most significant factor in the passive current case while at the micro scale the effect of these two factors on the passive current was found to be the same. The surface morphology of the formed patina on the corroded copper in both micro and macro systems reveal a more significant role of the chloride concentration on the structure and the grain size of the patinas. Finally, micro and macro electrochemical impedance spectroscopy of copper at various NaCl concentrations and pH values demonstrates a different behavior of copper after several potentiodynamic polarization cycles.

  8. Comparing polyaluminum chloride and ferric chloride for antimony removal.

    Science.gov (United States)

    Kang, Meea; Kamei, Tasuku; Magara, Yasumoto

    2003-10-01

    Antimony has been one of the contaminants required to be regulated, however, only limited information has been collected to date regarding antimony removal by polyaluminium chloride (PACl) and ferric chloride (FC). Accordingly, the possible use of coagulation by PACl or FC for antimony removal was investigated. Jar tests were used to determine the effects of solution pH, coagulant dosage, and pre-chlorination on the removal of various antimony species. Although high-efficiency antimony removal by aluminum coagulation has been expected because antimony is similar to arsenic in that both antimony and arsenic are a kind of metalloid in group V of the periodic chart, this study indicated: (1) removal density (arsenic or antimony removed per mg coagulant) for antimony by PACl was about one forty-fifth as low as observed for As(V); (2) although the removal of both Sb(III) and Sb(V) by coagulation with FC was much higher than that of PACl, a high coagulant dose of 10.5mg of FeL(-1) at optimal pH of 5.0 was still not sufficient to meet the standard antimony level of 2 microg as SbL(-1) for drinking water when around 6 microg as SbL(-1) were initially present. Consequently, investigation of a more appropriate treatment process is necessary to develop economical Sb reduction; (3) although previous studies concluded that As(V) is more effectively removed than As(III), this study showed that the removal of Sb(III) by coagulation with FC was much more pronounced than that of Sb(V); (4) oxidation of Sb(III) with chlorine decreased the ability of FC to remove antimony. Accordingly, natural water containing Sb(III) under anoxic condition should be coagulated without pre-oxidation.

  9. Benzalkonium Chloride and Glaucoma

    OpenAIRE

    Rasmussen, Carol A.; Kaufman, Paul L.; Kiland, Julie A.

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapo...

  10. "EARTH: The Operators' Manual" - a hybrid model (TV+online+in-person) to effectively communicate climate change science alongside sustainable energy solutions

    Science.gov (United States)

    Haines-stiles, G.; Alley, R. B.; Akuginow, E.

    2011-12-01

    Recent public opinion surveys have found that Americans underestimate the degree of agreement by climate scientists about global warming and climate change, and - despite growing evidence of ice sheet loss, ocean acidification, sea level rise and extreme weather events - believe less in warming trends in 2011 than they did earlier. The issue has become politicized and controversial. "EARTH: The Operators' Manual" is an informal science education project supported by NSF, the National Science Foundation. Its ambitious goal is to use a hybrid mix of broadcast programs appearing on public television and hosted by Penn State geoscientist, Richard Alley, together with on-site outreach events and online resources and tools, to present core climate science in engaging ways, and to combine that presentation of objective research with an overview of sustainable energy solutions. The project's content and communication strategies have been shaped in response to analyses of public opinion such as the SIX AMERICAS study and aim to address common "skeptic" arguments and share essential climate science. Social science research has also found that audiences seem more open to scientific information where the possibility of a positive response is also offered. The first hour-long PBS program aired nationally in April 2011, has since been re-broadcast, and is also available online. Two more programs will air in 2012, and the presentation at the Fall AGU Conference will preview segments from both programs. Five regionally-diverse science centers (in San Diego, Raleigh NC, St. Paul MN, Fort Worth TX and Portland OR) have hosted outreach events, with Richard Alley and other project participants, and will continue with additional activities through summer 2012. The project's website includes video clips, case studies of energy-saving initiatives world-wide and across the USA, plus an interactive "Energy Gauge" inviting users to assess their current Home, Travel, Food, and Goods and

  11. Extraction and stripping of rare earths using mixtures of acidic phosphorusbased reagents

    Institute of Scientific and Technical Information of China (English)

    WANG Xianglan; LI Wei; LI Deqian

    2011-01-01

    Studies were carried out on the extraction characters of trivalent rare earths from chloride solutions using organophosphorus acids 2-ethylhexylphosphonic acid mono-(2-ethylhexyl) ester (HEHEHP) combined with [di-(2-ethylhexyl)-phosphoric acid (HDEHP), isopropylphosphonic acid l-hexyl-4-ethyloctyl ester (HHEOIPP), bis(2,4,4-trimethylpentyl)-phosphinic acid (Cyanex 272), bis(2,4,4-trimethypen-tyl)-monothiophosphinic acid (Cyanex 302) or bis(2,4,4-trimethypentyl)-dithiophosphinic acid (Cyanex 301)] as extractants. The effect of the equilibrium aqueous acidity on the extraction was studied. According to the corresponding separation factors for adjacent pairs of rare earths,it could be concluded that HEHEHP and Cyanex 272 could be employed for the separation of Tm(Ⅲ), Yb(Ⅲ), Lu(Ⅲ) from the other rare earths. Taking Yb(Ⅲ) as an example, based on the different stripping acid, the potential of the stripping was estimated.

  12. Preparation and characterization of zirconium dioxide catalyst supports modified with rare earth elements

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, Masakuni; Kimura, Mareo (Toyota Central Research and Development Labs., Inc., Aichi (Japan))

    1991-08-15

    ZrO{sub 2} catlyst supports modified with rare earth elements were prepared by coprecipitation from an aqueous solution of zirconium oxychloride and rare earth chlorides. The crystallization of amorphous hydrous ZrO{sub 2} was inhibited by doping with rare earths; the crystallization temperature was elevated as the amount and ionic radius of the rare earth modifiers was increased. Only modification using cerium had no effect on the crystallization process. The behavior of cerium was different from that of other rare earth elements with valency +3. A metastable cubic phase was formed for ZrO{sub 2} modified with 10 mol.% lanthanum, neodymium and samarium by heating at 600degC. X-ray diffraction and Raman data indicated that the metastable phase had large microstrain and short-range ordering similar to tetragonal symmetry. Rare earth modified ZrO{sub 2} showed a large surface area and good thermal stability as a catalyst support. The carbon monoxide oxidation activity of iron was enhanced by modification with neodymium of ZrO{sub 2} supports. The results suggest the effectiveness of rare earth modified ZrO{sub 2} as catalyst supports. (orig.).

  13. Solid-liquid extraction of Gd(Ⅲ) and separation possibilities of rare earths from phosphoric acid solutions using Tulsion CH-93 and Tulsion CH-90 resins

    Institute of Scientific and Technical Information of China (English)

    S.Radhika; V.Nagaraju; B.Nagaphani Kumar; M.Lakshmi Kantam; B.Ramachandra Reddy

    2012-01-01

    Solid-liquid extraction of gadolinium was investigated from phosphoric acid medium using commercial amino phosphonic acid resin,Tulsion CH-93.The experimental conditions studied included equilibration time,acid concentration,mass of the resin,metal concentration,loading and elution.The percent extraction of Gd(Ⅲ) was studied as a function of phosphoric acid (0.05-3 mol/L) using Tulsion CH-93 resin.The corresponding lgD vs.equilibrium pH plot gave straight line with a slope of 1.8.The percent extraction decreased with acid concentration increasing,conforming ion exchange mechanism.Under observed experimental conditions the loading capacity of Tulsion CH-93 for gadolinium was 10.6 mg/g.Among several eluants screened,the quantitative elution of Gd(Ⅲ) from loaded Tulsion CH-93 was obtained with ammonium oxalate (0.15 mol/L).The extraction behavior of commonly associated metals with gadolinium was studied as a function of phosphoric acid concentration.Tulsion CH-93 resin showed selective extraction towards heavy rare earths (Lu and Yb) which could be separated from other rare earths at 3 mol/L H3PO4,similar to wet phosphoric acid (3-5 mol/L).On the other hand Gd(Ⅲ) and other rare earths were studied with chelating resin Tulsion CH-90.Light rare earths were highly extracted and these could be separated from heavy rare earths and Gd.

  14. The Influence of C3A Content in Cement on the Chloride Transport

    Directory of Open Access Journals (Sweden)

    Min Jae Kim

    2016-01-01

    Full Text Available The present study concerns the influence of C3A in cement on chloride transport in reinforced concrete. Three modified cement was manufactured in the variation of the C3A content, ranging from 6.0 and 10.5 up to 16.9%. The setting time of fresh concrete was measured immediately after mixing, together with the temperature at the time of initial set. For properties of hardened concrete in the variation in the C3A, a development of the compressive strength and chloride permeation were measured using mortar specimens. Simultaneously, chloride binding capacity was measured by the water extraction method. To ensure the influence of pore structure on chloride transport, the pore structure was examined by the mercury intrusion porosimetry. As a result, it was found that an increase in the C3A content resulted in an increase in chloride binding capacity. However, it seemed that increased binding of chlorides is related to the higher ingress of chlorides, despite denser pore structure. It may be attributed to the higher surface chloride, which could increase the gradient of chloride concentration from the surface, thereby leading to the higher level of chloride profiles. Substantially, the benefit of high C3A in resisting corrosion, arising from removal of free chlorides in the pore solution, would be offset by increased chloride ingress at a given duration, when it comes to the corrosion-free service life.

  15. Oxomemazine hydro-chloride.

    Science.gov (United States)

    Siddegowda, M S; Butcher, Ray J; Akkurt, Mehmet; Yathirajan, H S; Ramesh, A R

    2011-08-01

    IN THE TITLE COMPOUND [SYSTEMATIC NAME: 3-(5,5-dioxo-phen-othia-zin-10-yl)-N,N,2-trimethyl-propanaminium chloride], C(18)H(23)N(2)O(2)S(+)·Cl(-), the dihedral angle between the two outer aromatic rings of the phenothia-zine unit is 30.5 (2)°. In the crystal, the components are linked by N-H⋯Cl and C-H⋯Cl hydrogen bonds and C-H⋯π inter-actions.

  16. Corrosion of reinforcement induced by environment containing chloride and carbon dioxide

    Indian Academy of Sciences (India)

    Vladimír Živica

    2003-10-01

    Reinforced concrete structures during their exploitation may be exposed to the common action of carbonation and chlorides causing corrosion of steel reinforcement. Therefore, the related data seem to be interesting and important when the evaluation of the service life of the structures is the object of interest. This fact was a motivation for the present experimental study on the sequence of action of chloride solutions and carbonation of the embedding concrete. The results obtained show that carbonation of concrete foregoing the action of chloride solutions may intensify the process of corrosion of steel reinforcement in comparison to the converse sequence of the action of mentioned media. At the same time the natrium chloride solution has been shown as a more aggressive medium opposite to the calcium and magnesium chloride solutions.

  17. Chloride penetration into concrete under simulated field conditions

    Energy Technology Data Exchange (ETDEWEB)

    Motohashi, K.; Misra, S.; Yamamoto, A. (Kajima Corp., Tokyo (Japan))

    1991-10-31

    The purpose of this study is to clarify the effect of field conditions such curing period, slump, maximum size of aggregate, etc. on chloride penetration into concrete. With a view to closely simulate the field conditions, all specimens were exposed to chloride attack for five days after casting. From the preliminary results obtained after a six month immersion in 3.3% NaCl solution, higher degrees of chloride ingress were observed in cases when the concrete was prematurely exposed to chloride attack or had a higher slump. In addition, apart from properties, such as water-cement ratio, etc., the relative orientation of the direction of penetration to that of casting, the mortar content of the mix, and the properties of the transition zone between the coarse aggregate and mortar were found to affect the diffusivity of the chloride. Under a limited number of conditions, soluble chloride content was also illustrated in addition to the total chlorides. 10 refs., 6 figs., 6 tabs.

  18. Determination of neodymium in rare earth mixtures by fourth-derivative spectrophotometry

    Energy Technology Data Exchange (ETDEWEB)

    Naixing Wang; Weian Liang (Shandong Univ., Jinan, SD (China)); Ping Qi (Shandong Analysis and Test Center, Jinan (China))

    1991-11-20

    The absorption spectra corresponding to 4f electron transitions of the neodymium complex with xylenol orange and cetylpyridinium chloride in the presence of Triton X-100 are reported. The absorption by neo-dymium is increased by factor 666, compared with that of its chloride. Fourth-derivative spectra are used to increase the sensitivity and to eliminate interferences from other rare elements. Beer's law is obeyed for 1.4-7.2 {mu}g Nd in 25 ml of solution. Relative standard deviation is 0.8% for 5.0 {mu}g/25 ml (n=7). Detection limits are 5.0 ng ml{sup -1} for Nd alone and 11.0 ng ml{sup -1} in the presence of 45 ng of lanthanum. Satisfactory results were obtained for the determination of neodymium in rare earth mixtures. (author). 11 refs.; 4 figs.

  19. Extractive process for preparing high purity magnesium chloride hexahydrate

    Directory of Open Access Journals (Sweden)

    Fezei Radouanne

    2012-01-01

    Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

  20. Expanding earth

    Energy Technology Data Exchange (ETDEWEB)

    Carey, S.W.

    1976-01-01

    Arguments in favor of an expanding earth are presented. The author believes that the theory of plate tectonics is a classic error in the history of geology. The case for the expanding earth is organized in the following way: introductory review - face of the earth, development of expanding earth concept, necessity for expansion, the subduction myth, and definitions; some principles - scale of tectonic phenomena, non-uniformitarianism, tectonic profile, paleomagnetism, asymmetry of the earth, rotation of the earth, and modes of crustal extension; regional studies - western North America, Central America, South-East Asia, and the rift oceans; tests and cause of expansion. 824 references, 197 figures, 11 tables. (RWR)

  1. Preparation and Characterization of Anhydrous Magnesium Chloride in Organic Solvent%有机溶剂法无水氯化镁的制备与表征

    Institute of Scientific and Technical Information of China (English)

    周宁波; 陈白珍; 何新快; 李义兵

    2005-01-01

    Ammonium carnallite was synthesized by hydrated magnesium chloride in salt lake and ammonium chloride solution. Dehydrated ammonium carnallite was dissolved in methanol under low temperature by feeding ammonia, to prepare anhydrous magnesium chloride. The results show that anhydrous magnesium chloride contains magnesium oxide in an amount less than 0.1% by weight, the yield of magnesium chloride was above 99.5%. Ammonium carnallite, ammoniation magnesium chloride and anhydrous magnesium chloride were characterized by thermoanalysis, X-ray powder diffraction and scanning electron microscopy.

  2. Sulfur Earth

    Science.gov (United States)

    de Jong, B. H.

    2007-12-01

    Variations in surface tension affect the buoyancy of objects floating in a liquid. Thus an object floating in water will sink deeper in the presence of dishwater fluid. This is a very minor but measurable effect. It causes for instance ducks to drown in aqueous solutions with added surfactant. The surface tension of liquid iron is very strongly affected by the presence of sulfur which acts as a surfactant in this system varying between 1.9 and 0.4 N/m at 10 mass percent Sulfur (Lee & Morita (2002), This last value is inferred to be the maximum value for Sulfur inferred to be present in the liquid outer core. Venting of Sulfur from the liquid core manifests itself on the Earth surface by the 105 to 106 ton of sulfur vented into the atmosphere annually (Wedepohl, 1984). Inspection of surface Sulfur emission indicates that venting is non-homogeneously distributed over the Earth's surface. The implication of such large variation in surface tension in the liquid outer core are that at locally low Sulfur concentration, the liquid outer core does not wet the predominantly MgSiO3 matrix with which it is in contact. However at a local high in Sulfur, the liquid outer core wets this matrix which in the fluid state has a surface tension of 0.4 N/m (Bansal & Doremus, 1986), couples with it, and causes it to sink. This differential and diapiric movement is transmitted through the essentially brittle mantle (1024 Pa.s, Lambeck & Johnson, 1998; the maximum value for ice being about 1030 Pa.s at 0 K, in all likely hood representing an upper bound of viscosity for all materials) and manifests itself on the surface by the roughly 20 km differentiation, about 0.1 % of the total mantle thickness, between topographical heights and lows with concomitant lateral movement in the crust and upper mantle resulting in thin skin tectonics. The brittle nature of the medium though which this movement is transmitted suggests that the extremes in topography of the D" layer are similar in range to

  3. Solution-derived sodalite made with Si- and Ge-ethoxide precursors for immobilizing electrorefiner salt

    Energy Technology Data Exchange (ETDEWEB)

    Riley, Brian J.; Lepry, William C.; Crum, Jarrod V.

    2016-01-01

    Chlorosodalite has the general form of Na8(AlSiO4)6Cl2 and this paper describes experiments conducted to synthesize sodalite to immobilize a mixed chloride salt using solution-based techniques. Sodalites were made using different Group IV contributions from either Si(OC2H5)4 or Ge(OC2H5)4, NaAlO2, and a simulated spent electrorefiner salt solution containing a mixture of alkali, alkaline earth, and lanthanide chlorides. Additionally, 6 glass binders at low loadings of 5 mass% were evaluated as sintering aids for the consolidation process. The approach of using the organic Group IV additives can be used to produce large quantities of sodalite at room temperature and shows promise over a method where colloidal silica is used as the silica source. However, the small particle sizes inhibited densification during pressure-less sintering.

  4. Chloride on the Move

    KAUST Repository

    Li, Bo

    2017-01-09

    Chloride (Cl−) is an essential plant nutrient but under saline conditions it can accumulate to toxic levels in leaves; limiting this accumulation improves the salt tolerance of some crops. The rate-limiting step for this process – the transfer of Cl− from root symplast to xylem apoplast, which can antagonize delivery of the macronutrient nitrate (NO3−) to shoots – is regulated by abscisic acid (ABA) and is multigenic. Until recently the molecular mechanisms underpinning this salt-tolerance trait were poorly defined. We discuss here how recent advances highlight the role of newly identified transport proteins, some that directly transfer Cl− into the xylem, and others that act on endomembranes in ‘gatekeeper’ cell types in the root stele to control root-to-shoot delivery of Cl−.

  5. Benzalkonium chloride and glaucoma.

    Science.gov (United States)

    Rasmussen, Carol A; Kaufman, Paul L; Kiland, Julie A

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapoptosis, cytoskeleton changes, and immunoinflammatory reactions. These same effects have been reported in cultured human TM cells exposed to concentrations of BAK found in common glaucoma drugs and in the TM of primary open-angle glaucoma donor eyes. It is possible that a relationship exists between chronic exposure to BAK and glaucoma. The hypothesis that BAK causes/worsens glaucoma is being tested experimentally in an animal model that closely reflects human physiology.

  6. Partitioning of the rare earths and actinides between R7T7 nuclear glass alteration products and solution according to disposal conditions; Partage des terres rares et des actinides entre solution et produits d`alteration du verre nucleaire type R7T7 en fonction des conditions de stockage

    Energy Technology Data Exchange (ETDEWEB)

    Menard, O.

    1995-10-25

    The alteration of nuclear glass by water is liable to release radionuclides into the environment. Determining the release kinetics of these elements and their aqueous chemical forms are therefore essential steps in establishing the safety of a geological repository site. Leach tests were conducted with a nonradioactive specimen of the French ``R7T7`` light water containment glass spiked with U and Th, and with two R7T7 specimens spiked with {sup 237}Np and {sup 239}Pu, respectively. The alteration solution compositions were representative of deep groundwater and contained carbonate, sulfate, phosphate, fluorine and chlorine ions. The release of U, Th, Np and Pu, as well as of the rare earths La, Ce and Nd were monitored by ICP mass spectrometry and by {alpha} spectrometry. Scanning and transmission electron microscopic examination of the nonradioactive altered glass surfaces was also performed to assess the partitioning balance for the rare earths, U and Th between the glass alteration products and solution. The mobility of these elements depends on two competing mechanisms. The rare earths and thorium are incorporated in the alteration products (gel); the retention process is assumed to involve chemisorption or coprecipitation, enhanced in the gel layer by the presence of phosphate ions in particular. Conversely, the aqueous species in the alteration solutions (mainly anions) form complexes with the actinides and rare earths; this phenomenon is particularly evident with U and Np. The presence of carbonate ions favors this mobility. Plutonium differs from U and Np in that it is adsorbed mainly on colloids formed by glass dissolution, the principal factors governing its chemical evolution in solution. (author). refs., 122 figs., 185 tabs.

  7. Determination of metals and rare earths in leach solution of phosphogypsum by instrumental neutron activation analysis (INAA); Determinacao de metais e terras raras em solucao lixiviada de fosfogesso por AANI

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Gabriela J.L., E-mail: glcosta@ipen.br [Universidade Nove de Julho, Sao Paulo, SP (Brazil); Saueia, Catia H.R.; Mazzilli, Barbara P., E-mail: chsaueia@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The phosphogypsum is a sub-product of the fertilizer industries and is composed of the gypsum matrix (CaSO{sub 4}.2H{sub 2}O) which naturally contains high tenors of impurities such as 2P{sub O}5 and metals coming from the original phosphat rock. The Brazilian phosphogypsum and the various uses has been researched through his elementary and radiochemistry characterization. This work determine the metals (As, Ba, Co and Se) and rare earths (La, Ce, Sm, Eu, Tb and Lu) presents in samples of phosphogypsum leach solutions

  8. BIOSORPTION OF ALUMINIUM FROM SOLUTION BY DEAD ...

    African Journals Online (AJOL)

    biosorption of aluminium ions from solution was also evaluated. The result ... aqueous solution. The effect of pH on ... identified as Penicillium chrysogenum, Aspergillus niger,. Aspergillus ..... chloride macroquantities on the anion exchanger ...

  9. Benzalkonium Chloride Intoxication Mimicking Herpes Zoster Encephalitis

    Directory of Open Access Journals (Sweden)

    Ekrem Güler

    2011-06-01

    Full Text Available Benzalkonium chloride (BAC is a frequently used disinfectant and its most well-known side effect is contact dermatitis. In this report, two children who had vesicular dermatitis, headache, lethargy, fever and encephalopathy mimicking Herpes zoster encephalitis were presented. Their consciousness level improved on the second day. From the medical history it was understood that the mother had applied 20% BAC solution to the scalps of two children. The aim of the presentation of this report is to draw attention to the fact that BAC application to the scalp for treating pediculosis capitis may resemble the herpes encephalitis clinical picture.

  10. Inhibitive effect of Ce(III) and La(III) cations for AA2219 aluminium alloy corrosion in sodium chloride medium

    Energy Technology Data Exchange (ETDEWEB)

    Venkatasubramanian, G., E-mail: venkatguru_1966@yahoo.co.in [Department of Chemistry, Sathyabama University, Jeppiaar Nagar, Chennai 600119 (India); Sheik Mideen, A. [Department of Chemistry, Sathyabama University, Jeppiaar Nagar, Chennai 600119 (India); Jha, Abhay K. [Materials Processing Division, Vikram Sarabhai Space Centre, Indian Space Research Organisation, Thiruvananthapuram 695022 (India); Kulandainathan, M. Anbu [Electro Organic Chemistry Division, Central Electrochemical Research Institute, Karaikudi 630006 (India)

    2014-11-14

    In this paper, the rare earth chlorides were used to mitigate the dealloying of Al{sub 2}Cu intermetallic particles in aluminium alloy 2219-T87 plate exposed to 0.6 M NaCl solution. The negative shift of cathodic branches of potentiodynamic polarisation curves revealed the cathodic inhibition towards intermetallic dealloying. The low and high frequency time constants obtained from electrochemical impedance spectra revealed an increase in the corrosion resistance due to precipitation of rare earth oxides/hydroxides on the porous surface of native oxide film of aluminium alloy. Scanning electron microscopy coupled with energy dispersive X-ray analysis and atomic force microscopy revealed that intermetallic inclusions are the sites for the formation of cerium and lanthanum deposits which suppress copper redeposition and minimise galvanic interactions between the matrix and Al{sub 2}Cu particles. - Graphical abstract: Scanning electron microscopy and atomic force microscopy reveal the intermetallic inclusions, the sites for the formation of cerium and lanthanum oxide/hydroxide precipitates which prevent intermetallic de-alloying, suppress copper redeposition and minimise galvanic interactions in aluminium alloy 2219-T87 plate. - Highlights: • Ce{sup 3+} and La{sup 3+} act as cathodic inhibitors for AA2219-T87 aluminium alloy in 0.6 M NaCl. • Al{sub 2}Cu intermetallic particles are the sites for the formation of Ce and La precipitates. • The decrease in surface potential by rare earth chlorides confirms their inhibition.

  11. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride.

    Science.gov (United States)

    Ahn, Youngbeom; Kim, Jeong Myeong; Kweon, Ohgew; Kim, Seong-Jae; Jones, Richard C; Woodling, Kellie; Gamboa da Costa, Gonçalo; LiPuma, John J; Hussong, David; Marasa, Bernard S; Cerniglia, Carl E

    2016-11-22

    Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC) bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK) cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl), dodecyldimethylbenzylammonium chloride (C12BDMA-Cl), decyldimethylbenzylammonium chloride (C10BDMA-Cl), hexyldimethylbenzylammonium chloride, and benzyltrimethylammonium chloride was determined by incubation in 1/10-diluted tryptic soy broth (TSB) to determine if BCC bacteria have the ability to survive and inactivate these disinfectants. With BZK, C14BDMA-Cl, and C12BDMA-Cl, inhibition of the growth of 20 BCC strains was observed in disinfectant solutions that ranged from 64 to 256 µg/ml. The efflux pump inhibitor carbonyl cyanide m-chlorophenylhydrazone increased the sensitivity of bacteria to 64 µg/ml BZK. The 20 BCC strains grew well in 1/10-diluted TSB medium with BZK, C12BDMA-Cl, and C10BDMA-Cl; they absorbed and degraded the compounds in 7 days. Formation of benzyldimethylamine and benzylmethylamine as the initial metabolites suggested that the cleavage of the C alkyl-N bond occurred as the first step of BZK degradation by BCC bacteria. Proteomic data confirmed the observed efflux activity and metabolic inactivation via biodegradation in terms of BZK resistance of BCC bacteria, which suggests that the two main resistance mechanisms are intrinsic and widespread.

  12. The effect of pH on the corrosion behavior of intermetallic compounds Ni{sub 3}(Si,Ti) and Ni{sub 3}(Si,Ti) + 2Mo in sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Priyotomo, Gadang, E-mail: gada001@lipi.go.id; Nuraini, Lutviasari, E-mail: Lutviasari@gmail.com [Research Center for Metallurgy and Material, Indonesian Institute of Sciences, Kawasan PUSPIPTEK Gd.474, Setu, Tangerang Selatan, Banten 15314 (Indonesia); Kaneno, Yasuyuki, E-mail: kaneno@mtr.osakafu-u.ac.id [Department of Materials Science, Graduate School of Engineering, Osaka Prefecture University, 1-1 Gakuen-cho, Sakai, Osaka 599-8531 (Japan)

    2015-12-29

    The corrosion behavior of the intermetallic compounds, Ni{sub 3}(Si,Ti) (L1{sub 2}: single phase) and Ni{sub 3}(Si,Ti) + 2Mo (L1{sub 2} and (L12 + Ni{sub ss}) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EDAX: Energy Dispersive X-ray) in 0.5 kmol/m{sup 3} NaCl solutions at various pH. The corrosion behavior of nickel alloy C-276 was studied under the same experimental conditions as a reference. It was found that the uniform attack was observed on Ni{sub 3}(Si,Ti) for the immersion test at lower pH, while the pitting attack was observed on this compound for this test at neutral solution. Furthermore, Ni{sub 3}(Si,Ti)+2Mo had the preferential dissolution of L1{sub 2} compared to (L1{sub 2} + Ni{sub ss}) mixture region at lower pH, while pitting attack occurred in (L1{sub 2} + Ni{sub ss}) mixture region at neutral solution. For both intermetallic compounds, the magnitude of pitting and uniform attack decrease with increasing pH of solutions. From the immersion test and polarization curves, the corrosion resistance of Ni{sub 3}(Si,Ti)+2Mo is lower than that of Ni{sub 3}(Si,Ti), while the nickel alloy C-276 is the highest one at various pH of solutions. On the other hand, in the lower pH of solutions, the corrosion resistance of tested materials decreased significantly compared to those in neutral and higher pH of solutions.

  13. The DELTA 181 lithium thionyl chloride battery

    Science.gov (United States)

    Sullivan, Ralph M.; Brown, Lawrence E.; Leigh, A. P.

    In 1986, the Johns Hopkins University/Applied Physics Laboratory (JHU/APL) undertook the development of a sensor module for the DELTA 181 spacecraft, a low earth orbit (LEO) mission of less than two months duration. A large lithium thionyl chloride battery was developed as the spacecraft's primary power source, the first known such use for this technology. The exceptionally high energy density of the lithium thionyl chloride cell was the primary driver for its use, resulting in a completed battery with a specific energy density of 120 Wh/lb. Safety requirements became the primary driver shaping all aspects of the power system design and development due to concerns about the potential hazards of this relatively new, high-energy technology. However, the program was completed without incident. The spacecraft was launched on February 8, 1988, from Kennedy Space Center (KSC) with over 60,000 Wh of battery energy. It reentered on April 2, 1988, still operating after 55 days, providing a successful, practical, and visible demonstration of the use of this technology for spacecraft applications.

  14. EARTH ROADS ARE EASY

    Directory of Open Access Journals (Sweden)

    David O. Whitten

    2000-01-01

    Full Text Available The earliest European immigrants in America traveled on waterways and on pathways worn into the earth by animals and Native Americans. Once their communities began to thrive, settlers widened paths and cleared new roads and streets then began experimenting with inexpensive surfacing to reduce dust in dry weather and mud in wet. “Earth Roads Are Easy” investigates materials and techniques used to maintain primitive thoroughfares with a minimum of effort and expense. The options range from the mundane—clay, sand, gravel, calcium chloride, oil, and tar—to the extraordinary—water glass, adobe clay, beet juice, and carpeting.There is no more dfficult problem confronting highway engineers than that of properly constructing and maintaining an earth road. The work may be less spectacular than the construction and maintenance of hard-surfaced roads, but there is greater latitude in location, methods of construction and choice of materials, consequently there is more scope for the exercise of sound judgment on the part of the engineer.1

  15. Characterization of a non-aggregating silicon(IV) phthalocyanine in aqueous solution: toward red-light-driven photocatalysis based on earth-abundant materials.

    Science.gov (United States)

    Uslan, Canan; Oppelt, Kerstin T; Reith, Lorenz M; Sesalan, Behice Şebnem; Knör, Günther

    2013-09-21

    Photophysical and photochemical characterization of a novel cationic silicon phthalocyanine with excellent water solubility properties is reported. The robust red-light responsive compound shows very attractive features as a sensitizer for reductive and oxidative quenching processes to trigger photocatalytic substrate conversion in aqueous solution.

  16. Studies Update Vinyl Chloride Hazards.

    Science.gov (United States)

    Rawls, Rebecca

    1980-01-01

    Extensive study affirms that vinyl chloride is a potent animal carcinogen. Epidemiological studies show elevated rates of human cancers in association with extended contact with the compound. (Author/RE)

  17. The influence of the blast furnace slag replacement on chloride penetration in concrete

    Directory of Open Access Journals (Sweden)

    Juan Lizarazo Marriaga

    2011-05-01

    Full Text Available  Corrosion of steel reinforcement due to chloride penetration is the greatest cause of durability problems in concrete; intense international research has been carried out to understand and avoid this. This paper summarises the results of a theoretical and experimental research programme investigating the influence of blast furnace slag on chloride-related transport properties. The relationship between the apparent chloride diffusion coefficient, electrical resistivity and compressive strength was measured. Chloride, hydroxide, sodium and potassium’s intrinsic diffusion coefficients were obtained by using a computational model and an electrical migration test. The initial hydroxide composition of the pore solution, porosity and chloride binding capacity were also determined from the model. The results showed that blast furnace slag improved chloride penetration resistance, resulting in concrete which was less vulnerable to corrosion. 

  18. XPS of fast-frozen hematite colloids in NaCl aqueous solutions: I. Evidence for the formation of multiple layers of hydrated sodium and chloride ions induced by the {001} basal plane

    Energy Technology Data Exchange (ETDEWEB)

    Shchukarev, Andrei; Boily, Jean F.; Felmy, Andrew R.

    2007-12-13

    The influence of the {001} basal plane of hematite on the composition of fast-frozen centrifuged wet pastes of hematite prepared at pH 4 and 9 and at ionic strengths of 0, 10 and 100 mM NaCl was investigated by x-ray photoelectron spectroscopy. Two hematite preparations consisted of micrometer-sized platelets with 42% (HEM-1) and 95% (HEM-8) of the surface terminated by the {001} basal plane. A third preparation of spherical shape with no recognizable crystal plane (HEM-control) was used as a control to these experiments. All hematite samples responded to changes in pH and ionic strength, showing that acid/base reactions of surface hydroxyl groups control the composition of the paste. The HEM-1 and HEM-8 sample exhibited divergent properties at the highest ionic strength (100 mM) with energy loss features in the Na 1s and Cl 2p spectra and an important water content. As the spectra were typical of hydrated Na+ and Cl- ions and that the surface concentrations were unusually large, the HEM-1 and HEM-8 samples are proposed to induce the formation of a three-dimensional distribution of these ions in the paste. The sodium, chloride and water content was also correlated to the fraction of the {001} basal plane present in the sample and provided evidence for an approximate stochiometric Na:Cl:H2O ratio of 1:1:2. The {001} basal plane of hematite is consequently proposeD to be the cause of this feature.

  19. Solvent extraction-separation of La(III), Eu(III) and Er(III) ions from aqueous chloride medium using carbamoyl-carboxylic acid extractants

    Institute of Scientific and Technical Information of China (English)

    Reyhaneh Safarbali; Mohammad Reza Yaftian; Abbasali Zamani

    2016-01-01

    N,N-dibutyldiglycol amic acid (HLI) and N,N-dioctyldiglycol amic acid (HLI) were synthesized and characterized by con-ventional spectroscopic methods. These molecules were examined as extractants for extraction-separation of La(III), Eu(III) and Er(III), as representative ions of light, middle and heavy rare earths, from aqueous chloride solutions. The analysis of the extraction equilibria revealed that the extracted species of lanthanum and europium ions by both of the extractants had a 1:3 metal to ligand ratio. It was suggested that erbium ions were extracted into the organic phase via the formation of Er(LI or I)2Cl complexes. The effect of the organic diluents on the extraction-separation efficiency of the studied rare earths by HLI and HLI was investigated by comparing the results obtained in dichloromethane and carbon tetrachloride. Regardless to the diluent used, the order of selectivity presented by the investigated extractants was Er(III)>Eu(III)>La(III). It is noteworthy that, a significant enhancement in separation of the studied rare earths by the extractants was achieved in their competitive extraction experiments with respect to that obtained in single component extraction experiments. Applicability of the extractants for the removal of rare earth ions from spent Ni-MH batteries was tested by removal of La(III), Eu(III) and Er(III) ions from simulated leach solution of such batteries.

  20. Parameters Affecting Hydrogen Chloride Measurements

    Science.gov (United States)

    1993-06-01

    contain sea salt, which is hygroscopic because of the magnesium chloride present, or ammonium bisulfate , which mostly comes from sulfur pollution and is...boosters release hydrogen chloride as a combustion product, and hydrazines or nitric acid can be spilled from liquid fuel motors. Monitoring the...solubility constant, and the second is the acid ionization constant. From experimental work, the product of the two constants is well established (Reference

  1. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  2. Earth\\'s Mass Variability

    CERN Document Server

    Mawad, Ramy

    2014-01-01

    The perturbation of the Earth caused by variability of mass of Earth as additional reason with gravity of celestial bodies and shape of the Earth. The Earth eating and collecting matters from space and loss or eject matters to space through its flying in the space around the Sun. The source of the rising in the global sea level is not closed in global warming and icebergs, but the outer space is the additional important source for this rising. The Earth eats waters from space in unknown mechanism. The mass of the Earth become greater in November i.e. before transit apoapsis two months, and become latter in February i.e. after transit apoapsis to two months.

  3. Equilibrium, kinetic and mass transfer studies and column operations for the removal of arsenic(III) from aqueous solutions using acid treated spent bleaching earth.

    Science.gov (United States)

    Mahramanlioglu, M; Güçlü, K

    2004-09-01

    In the present study, a new adsorbent was produced from spent bleaching earth by H2SO4 impregnation method. The sorption of arsenic(III) by acid treated spent bleaching earth was studied to examine the possibility of utilizing this material in water treatment systems. The effect of time, pH, initial concentration, temperature on the adsorption of arsenic(III) was studied. Maximum adsorption was found to occur at pH 9.0. The adsorption process followed the first order Lagergren equation. Mass transfer coefficients and rate constants of intraparticle diffusion were calculated. The experimental data points were fitted to the Langmuir equation in order to calculate the adsorption capacity (Q0) of the adsorbent and the value of Q0 was found to be 0.46 mmol g(-1). In order to understand the adsorption mechanism, Dubinin-Radushkevich (DR) isotherm was used. The magnitude of E calculated from DR equation was found to be 5.12 kJ mol(-1). The heat of adsorption (deltaH0 = -30367 J mol(-1)) implied that the adsorption was physical exothermic adsorption. The column studies were also carried out to simulate water treatment processes. The capacity values obtained in column studies were found to be greater than the capacity values obtained in batch studies. This result was explained by the difference between batch system and column system. The factors that affect the capacity values of column and batch systems were explained. The effect of other anions on the adsorption of arsenic(III) in the presence of NO3-, SO4(2-), Cl-, Br- was studied. The presence of these anions did not affect the adsorption of arsenic(III) significantly.

  4. TESTING OF 304L STAINLESS STEEL IN NITRIC ACID ENVIRONMENTS WITH FLUORIDES AND CHLORIDES

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J.

    2010-10-04

    Impure radioactive material processed in nitric acid solutions resulted in the presence of chlorides in a dissolver fabricated from 304L stainless steel. An experimental program was conducted to study the effects of chloride in nitric acid/fluoride solutions on the corrosion of 304L stainless steel. The test variables included temperature (80, 95, and 110 C) and the concentrations of nitric acid (6, 12, and 14 M), fluoride (0.01, 0.1, and 0.2 M) and chloride (100, 350, 1000, and 2000 ppm). The impact of welding was also investigated. Results showed that the chloride concentration alone was not a dominant variable affecting the corrosion, but rather the interaction of chloride with fluoride significantly affected corrosion.

  5. Mercury toxicity in the shark (Squalus acanthias) rectal gland: apical CFTR chloride channels are inhibited by mercuric chloride.

    Science.gov (United States)

    Ratner, Martha A; Decker, Sarah E; Aller, Stephen G; Weber, Gerhard; Forrest, John N

    2006-03-01

    In the shark rectal gland, basolateral membrane proteins have been suggested as targets for mercury. To examine the membrane polarity of mercury toxicity, we performed experiments in three preparations: isolated perfused rectal glands, primary monolayer cultures of rectal gland epithelial cells, and Xenopus oocytes expressing the shark cystic fibrosis transmembrane conductance regulator (CFTR) chloride channel. In perfused rectal glands we observed: (1) a dose-dependent inhibition by mercury of forskolin/3-isobutyl-1-methylxanthine (IBMX)-stimulated chloride secretion; (2) inhibition was maximal when mercury was added before stimulation with forskolin/IBMX; (3) dithiothrietol (DTT) and glutathione (GSH) completely prevented inhibition of chloride secretion. Short-circuit current (Isc) measurements in monolayers of rectal gland epithelial cells were performed to examine the membrane polarity of this effect. Mercuric chloride inhibited Isc more potently when applied to the solution bathing the apical vs. the basolateral membrane (23 +/- 5% and 68 +/- 5% inhibition at 1 and 10 microM HgCl2 in the apical solution vs. 2 +/- 0.9% and 14 +/- 5% in the basolateral solution). This inhibition was prevented by pre-treatment with apical DTT or GSH; however, only the permeant reducing agent DTT reversed mercury inhibition when added after exposure. When the shark rectal gland CFTR channel was expressed in Xenopus oocytes and chloride conductance was measured by two-electrode voltage clamping, we found that 1 microM HgCl2 inhibited forskolin/IBMX conductance by 69.2 +/- 2.0%. We conclude that in the shark rectal gland, mercury inhibits chloride secretion by interacting with the apical membrane and that CFTR is the likely site of this action.

  6. 46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and...

  7. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  8. Inhibition of Chloride Induced Crevice Corrosion in Alloy 22 by Fluoride Ions

    Energy Technology Data Exchange (ETDEWEB)

    Carranza, R M; Rodr?guez, M A; Rebak, R B

    2005-10-09

    Alloy 22 (N06022) is highly resistant to localized corrosion. Alloy 22 may be susceptible to crevice corrosion in pure chloride (Cl{sup -}) solutions under aggressive environmental conditions. The effect of the fluoride (F{sup -}) over the crevice corrosion induced by chloride ions is still not well established. The objective of the present work was to explore the crevice corrosion resistance of this alloy to different mixtures of fluorides and chlorides. Cyclic potentiodynamic polarization (CPP) tests were conducted in deaerated aqueous solutions of pure halide ions and also in different mixtures of chloride and fluoride at 90 C and pH 6. The range of chloride concentration [Cl{sup -}] was 0.001 M {le} [Cl{sup -}] {le} 1 M and the range of molar fluoride to chloride ratio [F{sup -}]/[Cl{sup -}] was 0.1 {le} [F{sup -}]/[Cl{sup -}] {le} 10. Results showed that Alloy 22 was susceptible to crevice corrosion in all the pure chloride solutions but not in the pure fluoride solutions. Fluoride ions showed an inhibitor behavior only in mixtures with a molar ratio [F{sup -}]/[Cl{sup -}] > 2. For mixtures with a molar ratio [F{sup -}]/[Cl{sup -}] of 7 and 10 the inhibition of crevice corrosion was complete.

  9. Sulfur radical species form gold deposits on Earth.

    Science.gov (United States)

    Pokrovski, Gleb S; Kokh, Maria A; Guillaume, Damien; Borisova, Anastassia Y; Gisquet, Pascal; Hazemann, Jean-Louis; Lahera, Eric; Del Net, William; Proux, Olivier; Testemale, Denis; Haigis, Volker; Jonchière, Romain; Seitsonen, Ari P; Ferlat, Guillaume; Vuilleumier, Rodolphe; Saitta, Antonino Marco; Boiron, Marie-Christine; Dubessy, Jean

    2015-11-01

    Current models of the formation and distribution of gold deposits on Earth are based on the long-standing paradigm that hydrogen sulfide and chloride are the ligands responsible for gold mobilization and precipitation by fluids across the lithosphere. Here we challenge this view by demonstrating, using in situ X-ray absorption spectroscopy and solubility measurements, coupled with molecular dynamics and thermodynamic simulations, that sulfur radical species, such as the trisulfur ion S3(-), form very stable and soluble complexes with Au(+) in aqueous solution at elevated temperatures (>250 °C) and pressures (>100 bar). These species enable extraction, transport, and focused precipitation of gold by sulfur-rich fluids 10-100 times more efficiently than sulfide and chloride only. As a result, S3(-) exerts an important control on the source, concentration, and distribution of gold in its major economic deposits from magmatic, hydrothermal, and metamorphic settings. The growth and decay of S3(-) during the fluid generation and evolution is one of the key factors that determine the fate of gold in the lithosphere.

  10. Enhanced Microwave Resonance Properties of Pseudo-Tungsten-Bronze Ba6-3xR8+2xTi18O54 (R = Rare Earth) Solid Solutions Explained by Electron-Phonon Interaction

    Science.gov (United States)

    Wunderlich, Wilfried; Ohsato, Hitoshi

    2013-09-01

    Microwave dielectrics consisting of pseudo-tungsten-bronze solid solutions form compositional ordering at x = 2/3 with the Ba6-3xR8+2xTi18O54 (R = La, Nd, Pr, Sm, Eu, and Gd) formula. The Qf value of the x = 2/3 composition shows the highest value for Sm, but a discontinuity at Eu. When doping with heavier rare earth species, the crystal structure becomes unstable and needs stabilization with Nd. In this paper, we suggest for the first time that the electron-phonon interaction is responsible for this phenomenon. As the unit cells without Ba ions in the perovskite blocks caused tensile stress, the dielectric constant and dielectric losses increase by means of the ionic size of the dopant in the octahedral sites, but only when elements with a low electron-phonon interaction are used.

  11. Optical, thermal and magnetic studies of pure and cobalt chloride doped L-alanine cadmium chloride

    Science.gov (United States)

    Benila, B. S.; Bright, K. C.; Delphine, S. Mary; Shabu, R.

    2017-03-01

    Single crystals of L-alanine cadmium chloride (LACC) and cobalt chloride (Co2+) doped LACC have been grown by the slow evaporation solution growth technique. The grown crystals were subjected to various characterizations such as powder XRD, SXRD, FTIR, UV-vis, EDAX, TG/DTA, VSM, Dielectric and Second Harmonic Generation (SHG) measurements. The lattice parameters of the grown crystals were determined by single crystal X-ray analysis. EDAX analysis confirms the presence of Co2+ ion in the host material. The functional group and optical behavior of the crystals were identified from FTIR and UV-vis spectrum analysis. Electrical parameters such as dielectric constant, dielectric loss have been studied. The thermal stability of the compound was found out using TGA/DTA analysis. Second Harmonic Generation of the samples was confirmed by Kurtz-Perry powder technique. Magnetic properties of the crystals studied by VSM were also reported. The encouraging results show that the cobalt chloride doped LACC crystals have greater potential applications in optical devices.

  12. CO2 capture performance of bi-functional activated bleaching earth modified with basic-alcoholic solution and functionalization with monoethanolamine: isotherms, kinetics and thermodynamics.

    Science.gov (United States)

    Pongstabodee, Sangobtip; Pornaroontham, Phuwadej; Pintuyothin, Nuthapol; Pootrakulchote, Nuttapol; Thouchprasitchai, Nutthavich

    2016-10-01

    CO2 capture performance of bifunctional activated bleaching earth (ABE) was investigated at atmospheric pressure. The sorbents were characterized by means of X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), Caron-Hydrogen-Nitrogen analysis (CHN), Fourier transform infrared (FT-IR) and thermal gravimetric analysis (TGA). The CO2 capacity was enhanced via basic-modification and monoethanolamine (MEA) loading of the ABE sorbent to obtain a bifunctional surface property. Here, basic-modified calcined ABE with a 30wt.% MEA loading (SAB-30) showed the highest CO2 capture capacity, but this was decreased with excess MEA loading (>30wt.%). At a 10% (V/V) initial CO2 concentration feed, the maximum capacity of SAB-30 increased from 2.71mmol/g at 30°C (without adding moisture to the feed) to 3.3mmol/g at 50°C when adding 10% (V/V) moisture to the feed. Increasing the moisture concentration further reduced the maximum CO2 capacity due to the blocking effect of the excess moisture on the sorbent surface. However, SAB-30 could completely capture CO2 even in a 100% (V/V) initial CO2 concentration feed. A maximum CO2 capacity of 5.7mmol/g for SAB-30 was achieved at 30°C. Varying the ratio of sorbent weight to total flow rate of the gas stream had no discernible effect on the equilibrium CO2 capture capacity. Avrami's equation and Toth's isotherm model provided a good fitting for the data and suggested the presence of more than one reaction pathway in the CO2 capture process and the heterogeneous adsorption surface of SAB-30. Thermodynamics studies revealed that CO2 capture on the bifunctional SAB-30 is feasible, spontaneous and exothermic in nature.

  13. Extração simultânea de alumínio, cálcio, magnésio, potássio e sódio do solo com solução de cloreto de amônio Simultaneous extraction of aluminum, calcium, magnesium, potassium, and sodium with ammonium chloride solution

    Directory of Open Access Journals (Sweden)

    R. C. Boeira

    2004-10-01

    Full Text Available Atualmente, alguns laboratórios de análise de solo determinam Al, Ca e Mg trocáveis em extratos de KCl 1 mol L-1 e K e Na na solução extratora Mehlich-1, também usada na extração de fósforo. Outros laboratórios, que empregam a resina trocadora de ânions para P, avaliam também Ca, Mg e K no extrato, não sendo possível determinar Al e Na. Dessa forma, achou-se oportuno avaliar a extração com NH4Cl 1 mol L-1 na determinação simultânea dos cinco cátions trocáveis: Al, Ca, Mg, K e Na, em comparação aos extratores KCl e Mehlich-1. Utilizaram-se amostras coletadas em áreas de cultivo de fruteiras irrigadas da região Nordeste e na área experimental da Embrapa Meio Ambiente em Jaguariúna (SP. Os métodos utilizados foram: (a extração simultânea dos cinco cátions com NH4Cl 1 mol L-1, e (b extração de Ca, Mg e Al com KCl 1 mol L-1, e de K e Na com o extrator Mehlich-1. A solução de NH4Cl 1 mol L-1 apresentou maior capacidade de extração de Mg do solo do que a solução de KCl 1 mol L-1; as duas soluções se equivaleram quanto à capacidade de extração de Ca e de Al. A solução de NH4Cl extraiu mais K e Na do que a solução Mehlich-1. Conclui-se que a solução de NH4Cl é uma opção conveniente para a extração de Al, Ca, Mg, K e Na trocáveis do solo.Currently, part of the soil testing laboratories of Brazil determine exchangeable Al, Ca, and Mg in a 1 mol L-1 KCl soil extract and exchangeable sodium and potassium in the Mehlich-1 soil extract, which is also used for phosphorus extraction. Other laboratories use an anion exchange resin for P and also determine Ca, Mg and K in the same extract, while Al and Na cannot be determined. For this reason, it was considered a good opportunity to evaluate the simultaneous extraction of the five exchangeable cations: Al, Ca, Mg, K, and Na in a 1 mol L-1 NH4Cl solution, and compare the results with those obtained with potassium chloride and Mehlich-1 extractants. The soil

  14. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  15. Earth materials and earth dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, K; Shankland, T. [and others

    2000-11-01

    In the project ''Earth Materials and Earth Dynamics'' we linked fundamental and exploratory, experimental, theoretical, and computational research programs to shed light on the current and past states of the dynamic Earth. Our objective was to combine different geological, geochemical, geophysical, and materials science analyses with numerical techniques to illuminate active processes in the Earth. These processes include fluid-rock interactions that form and modify the lithosphere, non-linear wave attenuations in rocks that drive plate tectonics and perturb the earth's surface, dynamic recrystallization of olivine that deforms the upper mantle, development of texture in high-pressure olivine polymorphs that create anisotropic velocity regions in the convecting upper mantle and transition zone, and the intense chemical reactions between the mantle and core. We measured physical properties such as texture and nonlinear elasticity, equation of states at simultaneous pressures and temperatures, magnetic spins and bonding, chemical permeability, and thermal-chemical feedback to better characterize earth materials. We artificially generated seismic waves, numerically modeled fluid flow and transport in rock systems and modified polycrystal plasticity theory to interpret measured physical properties and integrate them into our understanding of the Earth. This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL).

  16. Analysis of Giga-size Earth Observation Data in Open Source GRASS GIS 7 - from Desktop to On-line Solutions.

    Science.gov (United States)

    Stepinski, T. F.; Mitasova, H.; Jasiewicz, J.; Neteler, M.; Gebbert, S.

    2014-12-01

    GRASS GIS is a leading open source GIS for geospatial analysis and modeling. In addition to being utilized as a desktop GIS it also serves as a processing engine for high performance geospatial computing for applications in diverse disciplines. The newly released GRASS GIS 7 supports big data analysis including temporal framework, image segmentation, watershed analysis, synchronized 2D/3D animations and many others. This presentation will focus on new GRASS GIS 7-powered tools for geoprocessing giga-size earth observation (EO) data using spatial pattern analysis. Pattern-based analysis connects to human visual perception of space as well as makes geoprocessing of giga-size EO data possible in an efficient and robust manner. GeoPAT is a collection of GRASS GIS 7 modules that fully integrates procedures for pattern representation of EO data and patterns similarity calculations with standard GIS tasks of mapping, maps overlay, segmentation, classification(Fig 1a), change detections etc. GeoPAT works very well on a desktop but it also underpins several GeoWeb applications (http://sil.uc.edu/ ) which allow users to do analysis on selected EO datasets without the need to download them. The GRASS GIS 7 temporal framework and high resolution visualizations will be illustrated using time series of giga-size, lidar-based digital elevation models representing the dynamics of North Carolina barrier islands over the past 15 years. The temporal framework supports efficient raster and vector data series analysis and simplifies data input for visual analysis of dynamic landscapes (Fig. 1b) allowing users to rapidly identify vulnerable locations, changes in built environment and eroding coastlines. Numerous improvements in GRASS GIS 7 were implemented to support terabyte size data processing for reconstruction of MODIS land surface temperature (LST) at 250m resolution using multiple regressions and PCA (Fig. 1c) . The new MODIS LST series (http://gis.cri.fmach.it/eurolst/) includes

  17. Lubiprostone: a chloride channel activator.

    Science.gov (United States)

    Lacy, Brian E; Levy, L Campbell

    2007-04-01

    In January 2006 the Food and Drug Administration approved lubiprostone for the treatment of chronic constipation in men and women aged 18 and over. Lubiprostone is categorized as a prostone, a bicyclic fatty acid metabolite of prostaglandin E1. Lubiprostone activates a specific chloride channel (ClC-2) in the gastrointestinal (GI) tract to enhance intestinal fluid secretion, which increases GI transit and improves symptoms of constipation. This article reviews the role of chloride channels in the GI tract, describes the structure, function, and pharmacokinetics of lubiprostone, and discusses clinically important data on this new medication.

  18. Photonic crystal fiber based chloride chemical sensors for corrosion monitoring

    Science.gov (United States)

    Wei, Heming; Tao, Chuanyi; Krishnaswamy, Sridhar

    2016-04-01

    Corrosion of steel is one of the most important durability issues in reinforced concrete (RC) structures because aggressive ions such as chloride ions permeate concrete and corrode steel, consequently accelerating the destruction of structures, especially in marine environments. There are many practical methods for corrosion monitoring in RC structures, mostly focusing on electrochemical-based sensors for monitoring the chloride ion which is thought as one of the most important factors resulting in steel corrosion. In this work, we report a fiber-optic chloride chemical sensor based on long period gratings inscribed in a photonic crystal fiber (PCF) with a chloride sensitive thin film. Numerical simulation is performed to determine the characteristics and resonance spectral response versus the refractive indices of the analyte solution flowing through into the holes in the PCF. The effective refractive index of the cladding mode of the LPGs changes with variations of the analyte solution concentration, resulting in a shift of the resonance wavelength, hence providing the sensor signal. This fiber-optic chemical sensor has a fast response, is easy to prepare and is not susceptible to electromagnetic environment, and can therefore be of use for structural health monitoring of RC structures subjected to such aggressive environments.

  19. Impact of the associated cation on chloride binding of Portland cement paste

    Energy Technology Data Exchange (ETDEWEB)

    De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of Science and Technology (Norway); Department of Engineering and Applied Sciences, University of Bergamo (Italy); Colombo, A. [Department of Structural Engineering, Norwegian University of Science and Technology (Norway); Department of Engineering and Applied Sciences, University of Bergamo (Italy); Coppola, L. [Department of Engineering and Applied Sciences, University of Bergamo (Italy); Justnes, H. [SINTEF Building and Infrastructure, Trondheim (Norway); Geiker, M.R. [Department of Structural Engineering, Norwegian University of Science and Technology (Norway)

    2015-02-15

    Well hydrated cement paste was exposed to MgCl{sub 2}, CaCl{sub 2} and NaCl solutions at 20 °C. The chloride binding isotherms for free chloride concentrations ranging up to 1.5 mol/l were determined experimentally. More chlorides were found to be bound when the associated cation was Mg{sup 2} {sup +} or Ca{sup 2} {sup +} compared to Na{sup +}. The chloride binding capacity of the paste appeared to be related to the pH of the exposure solution. In order to explain the cation dependency of the chloride binding a selection of samples was investigated in detail using experimental techniques such as TG, XRD and SEM–EDS to identify the phases binding the chlorides. The experimentally obtained data were compared with the calculations of a thermodynamic model, GEMS. It was concluded that the measured change in chloride binding depending on the cation was mainly governed by the pH of the exposure solution and thereby the binding capacity of the C-S-H.

  20. The impact of sulphate and magnesium on chloride binding in Portland cement paste

    Energy Technology Data Exchange (ETDEWEB)

    De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway); SINTEF Building and Infrastructure, Trondheim (Norway); Orsáková, D. [Department of Civil Engineering, Technical University of Brno, Brno (Czech Republic); Geiker, M.R. [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway)

    2014-11-15

    The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

  1. Superhydrophobic diatomaceous earth

    Science.gov (United States)

    Simpson, John T [Clinton, TN; D& #x27; Urso, Brian R [Clinton, TN

    2012-07-10

    A superhydrophobic powder is prepared by coating diatomaceous earth (DE) with a hydrophobic coating on the particle surface such that the coating conforms to the topography of the DE particles. The hydrophobic coating can be a self assembly monolayer of a perfluorinated silane coupling agent. The DE is preferably natural-grade DE where organic impurities have been removed. The superhydrophobic powder can be applied as a suspension in a binder solution to a substrate to produce a superhydrophobic surface on the substrate.

  2. Corrosion inhibition of copper in aqueous chloride solution by 1H-1,2,3-triazole and 1,2,4-triazole and their combinations: electrochemical, Raman and theoretical studies.

    Science.gov (United States)

    Ofoegbu, Stanley Udochukwu; Galvão, Tiago L P; Gomes, José R B; Tedim, João; Nogueira, Helena I S; Ferreira, M G S; Zheludkevich, M L

    2017-02-22

    Triazoles are well-known organic corrosion inhibitors of copper. 1H-1,2,3-Triazole and 1,2,4-triazole, two very simple molecules with the only difference being the positions of the nitrogen atoms in the triazole ring, were studied in this work as corrosion inhibitors of copper in 50 mM NaCl solution using a set of electrochemical and analytical techniques. The results of electrochemical tests indicate that 1H-1,2,3-triazole exhibited superior inhibitor properties but could not suppress anodic copper dissolution at moderate anodic potentials (>+300 mV SCE), while 1,2,4-triazole, although it exhibited higher anodic currents, suppressed anodic copper dissolution at very anodic potentials. Density functional theory calculations were also performed to interpret the measured data and trends observed in the electrochemical studies. The computational studies considered either the inhibitors isolated in the gaseous phase or adsorbed onto Cu(111) surface models. From the calculations, the mechanisms of the inhibitive effects of both triazoles were established and plausible mechanisms of formation of the protective films on the Cu surface were proposed. The results of this study hold positive implications for research in the areas of catalysis, and copper content control in water purification systems.

  3. Unsteady growth of ammonium chloride dendrites

    Science.gov (United States)

    Martyushev, L. M.; Terentiev, P. S.; Soboleva, A. S.

    2016-02-01

    Growth of ammonium chloride dendrites from aqueous solution is experimentally investigated. The growth rate υ and the radius ρ of curvature of branches are measured as a function of the relative supersaturation Δ for steady and unsteady growth conditions. It is shown that the experimental results are quantitatively described by the dependences ρ=a/Δ+b, υ=cΔ2, where the factors for primary branches are a=(1.3±0.2)·10-7 m, b=(2.5±0.4)·10-7 m, and c=(2.2±0.3)·10-4 m/s. The factor c is found to be approximately 7 times smaller for the side branches than that for the primary branches.

  4. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  5. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  6. [Headspace GC/MS analysis of residual vinyl chloride and vinylidene chloride in polyvinyl chloride and polyvinylidene chloride products].

    Science.gov (United States)

    Ohno, Hiroyuki; Mutsuga, Motoh; Kawamura, Yoko; Suzuki, Masako; Aoyama, Taiki

    2005-02-01

    A headspace GC/MS analysis method for the simultaneous determination of residual vinyl chloride (VC) and vinylidene chloride (VDC) in polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) products was developed. A test sample was swelled overnight with N,N-dimethylacetamide in a sealed vial. The vial was incubated for 1 hour at 90 degrees C, then the headspace gas was analyzed by GC/MS using a PLOT capillary column. The recoveries from spiked PVC and PVDC samples were 90.0-112.3% for VC and 85.2-108.3% for VDC. The determination limits were 0.01 microg/g for VC and 0.06/microg/g for VDC, respectively. By this method, VC was detected in two PVC water supply pipes at the levels of 0.61 and 0.01 microg/g. On the other hand, VC and VDC were not detected in any of the food container-packages or toys tested.

  7. The influence of organic structure and rare earth metal cation on the corrosion efficiency observed on AS1020 steel compared with La(4OHCin3

    Directory of Open Access Journals (Sweden)

    Marianne Seter

    2015-01-01

    Full Text Available Whilst the corrosion protection of steel in aqueous chloride environments by the rare earth inhibitor lanthanum 4-hydroxycinnamate is well known, the influence of the structural variation of the organic component as well as the nature of the metal centre has not previously been addressed. Herein we show that praseodymium 4-hydroxy cinnamate is comparable to its lanthanum counterpart in aqueous solution. On the other hand, cerium 4-hydroxycinnamate and lanthanum 2-hydroxycinnamate show poor corrosion protection performance while lanthanum 3-hydroxycinnamate provides a level of inhibition between these. These differences are shown to be related to the speciation in solution and are postulated to be linked to steric influences which are likely to affect the bonding environment within the rare earth compound itself, as well as its bonding with the steel substrate.

  8. Estimating the chloride transport in cement paste

    Directory of Open Access Journals (Sweden)

    Princigallo, A.

    2012-06-01

    Full Text Available A method was developed to measure the diffusion coefficient of chloride ions in cement paste based on an analytical solution to Fick’s 2nd law in a cylindrical coordinate system. This natural method yielded diffusivity results within as little as a month. Testing time was reduced by exploiting the three-dimensional inward flux in the specimen. In an attempt to determine the saturation concentration, dense portland cement pastes were exposed to a concentrated chloride solution. The method proved to be useful for exploring cement hydration-induced changes in the diffusion coefficient of cement paste.

    Se ha desarrollado un método para medir el coeficiente de difusión de los iones cloruro en la pasta de cemento, partiendo de una aplicación analítica de la segunda ley de Fick en un sistema de coordinadas cilíndrico. Este método, que es natural, demostró ser capaz de producir resultados de difusividad en tan solo un mes. Se consiguió reducir el tiempo de ensayo mediante el aprovechamiento de la tridimensionalidad del flujo desde el exterior al interior de la probeta. A fin de determinar la concentración de saturación, se sometieron las pastas de cemento Portland a una disolución de cloruros concentrada. Este método resultó ser útil en el estudio de los cambios del coeficiente de difusión de la pasta de cemento provocados por las reacciones de hidratación que tienen lugar en esta.

  9. 21 CFR 173.375 - Cetylpyridinium chloride.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No... Nutrition's Library, Food and Drug Administration, 5100 Paint Branch Pkwy., College Park, MD 20740, or...

  10. The Removal of NH3-N from the Waste Water of Producing Tribasic Copper Chloride from Waste Etching Solution Containing Copper%含铜蚀刻废液生产碱式氯化铜废水的脱氨氮处理

    Institute of Scientific and Technical Information of China (English)

    邹鸿图

    2012-01-01

    本论文针对利用含铜蚀刻废液生产碱式氯化铜(TBCC)豹过程中产生高氨氮废水的问题,提出了废水的脱氨氮处理工艺——蒸氨,并针对蒸氨设备进行了具体参数的调试,提出了找出了最佳的生产条件:蒸氨进料的pH不能低于11.3(25℃),处理量为3.5m3/h,蒸汽开度为88%。%The paper presented a method to treat the waste water from producing tribasical copper chloride from waste etching solution containing copper, which contains high NH3-N. The method was ammonia steaming, and experiments were done to test the removal rate at different operating parameters. The best operating parameter was thought to be: pH ≥ 11.3 (25 ℃), inlet amount of waste water 3.5 m3/h, opening of steaming valve 88 %.

  11. Snowball Earth

    OpenAIRE

    2016-01-01

    In the ongoing quest to better understand where life may exist elsewhere in the Universe, important lessons may be gained from our own planet. In particular, much can be learned from planetary glaciation events that Earth suffered ∼600 million years ago, so-called `Snowball Earth' episodes. I begin with an overview of how the climate works. This helps to explain how the ice-albedo feedback effect can destabilise a planet's climate. The process relies on lower temperatures causing more ice to ...

  12. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P. A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  13. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  14. Digital Earth - A sustainable Earth

    Science.gov (United States)

    Mahavir

    2014-02-01

    All life, particularly human, cannot be sustainable, unless complimented with shelter, poverty reduction, provision of basic infrastructure and services, equal opportunities and social justice. Yet, in the context of cities, it is believed that they can accommodate more and more people, endlessly, regardless to their carrying capacity and increasing ecological footprint. The 'inclusion', for bringing more and more people in the purview of development is often limited to social and economic inclusion rather than spatial and ecological inclusion. Economic investment decisions are also not always supported with spatial planning decisions. Most planning for a sustainable Earth, be at a level of rural settlement, city, region, national or Global, fail on the capacity and capability fronts. In India, for example, out of some 8,000 towns and cities, Master Plans exist for only about 1,800. A chapter on sustainability or environment is neither statutorily compulsory nor a norm for these Master Plans. Geospatial technologies including Remote Sensing, GIS, Indian National Spatial Data Infrastructure (NSDI), Indian National Urban Information Systems (NUIS), Indian Environmental Information System (ENVIS), and Indian National GIS (NGIS), etc. have potential to map, analyse, visualize and take sustainable developmental decisions based on participatory social, economic and social inclusion. Sustainable Earth, at all scales, is a logical and natural outcome of a digitally mapped, conceived and planned Earth. Digital Earth, in fact, itself offers a platform to dovetail the ecological, social and economic considerations in transforming it into a sustainable Earth.

  15. Intrinsic Resistance of Burkholderia cepacia Complex to Benzalkonium Chloride

    Directory of Open Access Journals (Sweden)

    Youngbeom Ahn

    2016-11-01

    Full Text Available Pharmaceutical products that are contaminated with Burkholderia cepacia complex (BCC bacteria may pose serious consequences to vulnerable patients. Benzyldimethylalkylammonium chloride (BZK cationic surfactants are extensively used in medical applications and have been implicated in the coselection of antimicrobial resistance. The ability of BCC to degrade BZK, tetradecyldimethylbenzylammonium chloride (C14BDMA-Cl, dodecyldimethylbenzylammonium chloride (C12BDMA-Cl, decyldimethylbenzylammonium chloride (C10BDMA-Cl, hexyldimethylbenzylammonium chloride, and benzyltrimethylammonium chloride was determined by incubation in 1/10-diluted tryptic soy broth (TSB to determine if BCC bacteria have the ability to survive and inactivate these disinfectants. With BZK, C14BDMA-Cl, and C12BDMA-Cl, inhibition of the growth of 20 BCC strains was observed in disinfectant solutions that ranged from 64 to 256 µg/ml. The efflux pump inhibitor carbonyl cyanide m-chlorophenylhydrazone increased the sensitivity of bacteria to 64 µg/ml BZK. The 20 BCC strains grew well in 1/10-diluted TSB medium with BZK, C12BDMA-Cl, and C10BDMA-Cl; they absorbed and degraded the compounds in 7 days. Formation of benzyldimethylamine and benzylmethylamine as the initial metabolites suggested that the cleavage of the C alkyl-N bond occurred as the first step of BZK degradation by BCC bacteria. Proteomic data confirmed the observed efflux activity and metabolic inactivation via biodegradation in terms of BZK resistance of BCC bacteria, which suggests that the two main resistance mechanisms are intrinsic and widespread.

  16. Cystic Fibrosis (CF): Chloride Sweat Test

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Cystic Fibrosis (CF) Chloride Sweat Test KidsHealth > For Parents > Cystic Fibrosis (CF) Chloride Sweat Test Print A A A ... It Is A chloride sweat test helps diagnose cystic fibrosis (CF) , an inherited disorder that makes kids sick ...

  17. 21 CFR 184.1426 - Magnesium chloride.

    Science.gov (United States)

    2010-04-01

    ... mineral bischofite. It is prepared by dissolving magnesium oxide, hydroxide, or carbonate in aqueous... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O,...

  18. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  19. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  20. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...