WorldWideScience

Sample records for dysprosium 162 target

  1. Isolation of {sup 163}Ho from dysprosium target material by HPLC for neutrino mass measurements

    Energy Technology Data Exchange (ETDEWEB)

    Mocko, Veronika; Taylor, Wayne A.; Nortier, Francois M.; Engle, Jonathan W.; Pollington, Anthony D.; Kunde, Gerd J.; Rabin, Michael W.; Birnbaum, Eva R. [Los Alamos National Laboratory, Los Alamos, NM (United States). Chemistry Div.; Barnhart, Todd E.; Nickles, Robert J. [Univ. Wisconsinn, Madison, WI (United States). Dept. of Medical Physics

    2015-07-01

    The rare earth isotope {sup 163}Ho is of interest for neutrino mass measurements. This report describes the isolation of {sup 163}Ho from a proton-irradiated dysprosium target and its purification. A Dy metal target was irradiated with 16 MeV protons for 10 h. After target dissolution, {sup 163}Ho was separated from the bulk Dy via cation-exchange high performance liquid chromatography using 70 mmol dm{sup -3} α-hydroxyisobutyric acid as the mobile phase. Subsequent purification of the collected Ho fraction was performed to remove the α-hydroxyisobutyrate chelating agent and to concentrate the Ho in a low ionic strength aqueous matrix. The final solution was characterized by MC-ICP-MS to determine the {sup 163}Ho/{sup 165}Ho ratio, {sup 163}Ho and the residual Dy content. The HPLC purification process resulted in a decontamination factor 1.4 x 10{sup 5} for Dy. The isolated Ho fraction contained 24.8 ± 1.3 ng of {sup 163}Ho corresponding to holmium recovery of 72 ± 3%.

  2. Synthesis and characterization of tetraphenylporphyrinate of dysprosium route dysprosium acetylacetonate

    International Nuclear Information System (INIS)

    Martinez M, V.

    1992-01-01

    Dysprosium bis (tetraphenylporphyrinate) and bis (dysprosium) Tris (tetraphenylporphyrinate) were synthesized from dysprosium tetraphenylporphyrinate prepared in situ, and characterized by IR, UV-vis, TGA, DTA, EPR and magnetic susceptibility measurements. The double decker compound was obtained by direct oxidation of the HDy(TPP) 2 intermediate. The existence of the radical anion, (TPP) - , in the double decker product was conformed by EPR spectrometry. Dysprosium monoporphyrinate was isolated and characterized by the same techniques. (Author)

  3. Neutron capture measurements and resonance parameters of dysprosium

    Energy Technology Data Exchange (ETDEWEB)

    Shin, S.G.; Kye, Y.U.; Namkung, W.; Cho, M.H. [Pohang University of Science and Technology, Division of Advanced Nuclear Engineering, Pohang, Gyeongbuk (Korea, Republic of); Kang, Y.R.; Lee, M.W. [Dongnam Inst. of Radiological and Medical Sciences, Research Center, Busan (Korea, Republic of); Kim, G.N. [Kyungpook National University, Department of Physics, Daegu (Korea, Republic of); Ro, T.I. [Dong-A University, Department of Physics, Busan (Korea, Republic of); Danon, Y.; Williams, D. [Rensselaer Polytechnic Institute, Department of Mechanical, Aerospace, and Nuclear Engineering, Troy, NY (United States); Leinweber, G.; Block, R.C.; Barry, D.P.; Rapp, M.J. [Naval Nuclear Laboratory, Knolls Atomic Power Laboratory, Schenectady, NY (United States)

    2017-10-15

    Neutron capture yields of dysprosium isotopes ({sup 161}Dy, {sup 162}Dy, {sup 163}Dy, and {sup 164}Dy) were measured using the time-of-flight method with a 16 segment sodium iodide multiplicity detector. The measurements were made at the 25m flight station at the Gaerttner LINAC Center at Rensselaer Polytechnic Institute. Resonance parameters were obtained using the multilevel R-matrix Bayesian code SAMMY. The neutron capture data for four enriched dysprosium isotopes and one natural dysprosium sample were sequentially fitted. New resonances not listed in ENDF/B-VII.1 were observed. There were 29 and 17 new resonances from {sup 161}Dy and {sup 163}Dy isotopes, respectively. Six resonances from {sup 161}Dy isotope, two resonances from {sup 163}Dy, and four resonances from {sup 164}Dy were not observed. The capture resonance integrals of each isotope were calculated with the resulting resonance parameters and those of ENDF/B-VII.1 in the energy region from 0.5 eV to 20 MeV and were compared to the capture resonance integrals with the resonance parameters from ENDF/B-VII.1. A resonance integral value of the natural dysprosium calculated with present resonance parameters was 1405 ± 3.5 barn. The value is ∝ 0.3% higher than that obtained with the ENDF/B-VII.1 parameters. The distributions of the present and ENDF/B-VII.1 neutron widths were compared to a Porter-Thomas distribution. Neutron strength functions for {sup 161}Dy and {sup 163}Dy were calculated with the present resonance parameters and both values were in between the values of ''Atlas of Neutron Resonances'' and ENDF/B-VII.1. The present radiation width distributions of {sup 161}Dy and {sup 163}Dy were fitted with the χ{sup 2} distribution by varying the degrees of freedom. (orig.)

  4. On polymorphism of dysprosium trichloride

    Energy Technology Data Exchange (ETDEWEB)

    Zakiryanova, Irina D.; Khokhlov, Vladimir A.; Salyulev, Alexander B.; Korzun, Iraida V. [RAS Ural Branch, Ekaterinburg (Russian Federation). Institute of High-Temperature Electrochemistry

    2015-07-01

    For the first time, the structure of crystalline DyCl{sub 3} over a wide temperature range from room temperature to melting point was studied by Raman spectroscopy. The phonon modes (cm{sup -1}) of dysprosium trichloride (monoclinic crystal lattice of AlCl{sub 3} type, Z = 4, CN = 6) at room temperature are 257 (A{sub 1g}), 201 (E{sub g}), 112 (E{sub g}), 88 (A{sub 1g}), and 63 (E{sub g}). The monoclinic structure of the crystalline DyCl{sub 3} C{sub 2h}{sup 3} symmetry was found to remain constant over the studied temperature range. No polymorphic transformation in the solid state was detected. Gravimetry, calorimetry, and mass spectrometry have been used in addition to support the conclusions made on the basis of Raman spectroscopic data.

  5. On polymorphism of dysprosium trichloride

    International Nuclear Information System (INIS)

    Zakiryanova, Irina D.; Khokhlov, Vladimir A.; Salyulev, Alexander B.; Korzun, Iraida V.

    2015-01-01

    For the first time, the structure of crystalline DyCl 3 over a wide temperature range from room temperature to melting point was studied by Raman spectroscopy. The phonon modes (cm -1 ) of dysprosium trichloride (monoclinic crystal lattice of AlCl 3 type, Z = 4, CN = 6) at room temperature are 257 (A 1g ), 201 (E g ), 112 (E g ), 88 (A 1g ), and 63 (E g ). The monoclinic structure of the crystalline DyCl 3 C 2h 3 symmetry was found to remain constant over the studied temperature range. No polymorphic transformation in the solid state was detected. Gravimetry, calorimetry, and mass spectrometry have been used in addition to support the conclusions made on the basis of Raman spectroscopic data.

  6. Can a dysprosium shortage threaten green energy technologies?

    International Nuclear Information System (INIS)

    Hoenderdaal, Sander; Tercero Espinoza, Luis; Marscheider-Weidemann, Frank; Graus, Wina

    2013-01-01

    Dysprosium, one of the various rare earth elements, is currently for more than 99% mined in China. As China is reducing its exports, new mining projects outside of China are needed to sustain supply and meet future demands. Dysprosium is mainly used in permanent magnets to retain the magnet's strength at elevated temperatures. Therefore, the use of dysprosium doped permanent magnets is preferred in electric vehicles and direct-drive wind turbines. Based on four scenarios it could be shown that dysprosium demand will probably outstrip supply in the short term (up to 2020). Although new mines are being developed, it takes several years for them to become productive. For the long term it is expected that enough dysprosium oxide is available in the earth crust (which is economically feasible to mine with current dysprosium prices) to fulfil the projected demand of dysprosium up to 2050. Recycling of dysprosium can further secure dysprosium supply in the long term by reducing primary dysprosium use by 35% in 2050. Electric vehicles are likely to play a dominant role in future increases in dysprosium demand. Even with the limited market share in 2011, electric vehicles already contribute to 20% of dysprosium use. -- Highlights: ► Dysprosium may hamper the implementation of electric cars and wind mills. ► In the short term (up to 2020) a deficit of dysprosium supply can be expected. ► In the long term (up to 2050) sufficient dysprosium is available. ► Electric vehicles are expected to dominate future dysprosium demand. ► China's dominance in dysprosium supply is likely to decrease by 2020.

  7. Resonance ionization spectroscopy in dysprosium

    Energy Technology Data Exchange (ETDEWEB)

    Studer, D., E-mail: dstuder@uni-mainz.de; Dyrauf, P.; Naubereit, P.; Heinke, R.; Wendt, K. [Johannes Gutenberg-Universität Mainz, Institut für Physik (Germany)

    2017-11-15

    We report on resonance ionization spectroscopy (RIS) of high-lying energy levels in dysprosium. We developed efficient excitation schemes and re-determined the first ionization potential (IP) via analysis of Rydberg convergences. For this purpose both two- and three-step excitation ladders were investigated. An overall ionization efficiency of 25(4) % could be demonstrated in the RISIKO mass separator of Mainz University, using a three-step resonance ionization scheme. Moreover, an extensive analysis of the even-parity 6sns- and 6snd-Rydberg-series convergences, measured via two-step excitation was performed. To account for strong perturbations in the observed s-series, the approach of multichannel quantum defect theory (MQDT) was applied. Considering all individual series limits we extracted an IP-value of 47901.76(5) cm{sup −1}, which agrees with the current literature value of 47901.7(6) cm{sup −1}, but is one order of magnitude more precise.

  8. Nature of the magnetic susceptibility of dysprosium. Paramagnetic susceptibility of dysprosium - yttrium alloys

    International Nuclear Information System (INIS)

    Demidov, V.G.; Levitin, R.Z.; Chistyakov, O.D.

    1976-01-01

    The paramagnetic susceptibility of single crystals of dysprosium-yttirum alloys is measured in the basal plane and along the hexagonal axis. It is shown that the susceptibility of the alloys obeys the Curie-Weiss law, the effective magnetic moments allong the different directions being the same and the paramagnetic Curie temperatures being different. The difference between the paramagnetic Curie temperatures in the basal plane and along the hexagonal axis is independent of the dysprosium concentration in the alloy. As a comparison with the theoretical models of magnetic anisotropy shows, this is an indication that the magnetic anisotropy of dysprosium - yttrium alloys is of a single-ion nature

  9. Isotopic shifts and configuration mixing in the dysprosium II spectrum

    International Nuclear Information System (INIS)

    Aufmuth, P.

    1977-01-01

    Using a photoelectric Fabry-Perot spectrometer with digital data acquisition, the isotopic shifts of all stable dysprosium isotopes (Z = 66, A = 156, 158, 160, 161, 162, 163, 164) have been measured in transitions from the groundstate configuration 4f 10 6s to the excited configurations 4f 9 5d6s, 4f 9 5d 2 , and 4f 10 6p of the spark spectrum. Mass and volume effects have been seperated; the results are compared with arc spectrum measurements. From the volume effect of a pure s-p transition the change of the mean electric quadratic nuclear radius delta 2 > has been calculated. In order to test fine structure calculations of the Dy II spectrum, the isotopic shifts of 29 lines of the isotopes 162 Dy and 164 Dy have been measured. Based on the sharing rule, the reported configuration mixing could be confirmed in principle; for one energy level (E = 22908 K) the asignement has been proved to be false, in the case of three other levels (E = 22467, 22672, and 28885 K) the asignement is doubtfull. For the ground state levels 4f 10 6s 6 I the influence of relativistic effects could be proved; these effects can be interpreted in the framework of a parametric representation of the isotopic shift. The order of magnitude of the crossed second order effects has been estimated. (orig.) [de

  10. Semiconductor composition containing iron, dysprosium, and terbium

    Science.gov (United States)

    Pooser, Raphael C.; Lawrie, Benjamin J.; Baddorf, Arthur P.; Malasi, Abhinav; Taz, Humaira; Farah, Annettee E.; Kalyanaraman, Ramakrishnan; Duscher, Gerd Josef Mansfred; Patel, Maulik K.

    2017-09-26

    An amorphous semiconductor composition includes 1 to 70 atomic percent iron, 15 to 65 atomic percent dysprosium, 15 to 35 atomic percent terbium, balance X, wherein X is at least one of an oxidizing element and a reducing element. The composition has an essentially amorphous microstructure, an optical transmittance of at least 50% in at least the visible spectrum and semiconductor electrical properties.

  11. Dysprosium complexes with the tetraphenylporphyrin macrocyclic ligand

    International Nuclear Information System (INIS)

    Martinez M, V.; Padilla, J.; Ramirez, F.M.

    1992-04-01

    In this report, the results obtained on the synthesis, characterization and study of the chemical behavior of dysprosium complex with the acetylacetone chelating agent (Hacac) and the tetraphenylporphyrin macrocyclic ligand (H 2 TFP) are given. Based on the literature but according to our necessities and interest, the appropriate methodology settled down from the synthesis of prime matters until the obtaining and characterization of the products. The acetyl acetonate complex was obtained of mono hydrated dysprosium [Dy(acac) 3 . H 2 0] and trihydrated [Dy(acac) 3 .3 H 2 0], the mono tetra phenyl porphyrinate [Dy(TFP)(acac). 2 ac] the double sandwich of the dysprosium porphyrinate [Dy(TFP) 2 ] and the triple sandwich of the dysprosium porphyrinate [Dy(TFP) 3 . 2 TCB] (TCB = trichlorobenzene). Its were characterized by their melting points, solubility, IR, UV, TGA and DTA both first and besides the techniques already mentioned for NMR'H, RPE and Magnetic susceptibility the three last complexes. From the spectroscopic point of view, IR and RPE its suggested the existence of a complex of inverse mixed valence [Dy(TFP) 2- (TFP) 1- ] for the Dy(TFP) 2 as a result of the existence of the free radical (TFP' 1- and that it was not in none of the other porphyrin compounds. In the NMR'H spectra of the compounds were not observed signals in the region from 0 to 10 ppm that which shows that the dysprosium complexes in special those of the porphyrin type are highly paramagnetic and its could be used as displacement reagents, creators of images and contrast agents of great utility in these days in studies of NMR, technique today by today used in medical diagnoses. (Author)

  12. Heat capacity measurements on dysprosium titanate

    International Nuclear Information System (INIS)

    Kandan, R.; Prabhakara Reddy, B.; Panneerselvam, G.; Nagarajan, K.

    2014-01-01

    Dysprosium titanate is considered as a candidate material for use in the control rods of future nuclear reactors. The Dy 2 TiO 5 compound was prepared by solid-state synthesis and characterized by XRD technique. The high temperature enthalpy increments of dysprosium titanates have been measured for the first time by employing the method of inverse drop calorimetry in the temperature range 748-1645 K by using high temperature drop calorimeter. The calorimeter, the method of measurement and the procedure adopted for enthalpy increment measurements and analysis of the measured data to compute thermodynamic functions have been described elsewhere. The measured enthalpy increments were fitted to polynomial in temperature by using the least squares method. The fit equation in the temperature range from 298 to 1800 K is given

  13. High temperature oxidation kinetics of dysprosium particles

    Energy Technology Data Exchange (ETDEWEB)

    Jaques, Brian J.; Butt, Darryl P., E-mail: DarrylButt@BoiseState.edu

    2015-09-25

    Highlights: • The oxidation behavior of dysprosium particles was studied from 500 to 1000 °C. • Activation energy in initial region found as 8–25 kJ/mol, depending on atmosphere. • Activation energy in intermediate region found as 80–95 kJ/mol. • The oxide grows at the metal–oxide interface. • Generally, the formed oxide behaved as a p-type semiconductor. - Abstract: Rare earth elements have been recognized as critical materials for the advancement of many strategic and green technologies. Recently, the United States Department of Energy has invested many millions of dollars to enhance, protect, and forecast their production and management. The work presented here attempts to clarify the limited and contradictory literature on the oxidation behavior of the rare earth metal, dysprosium. Dysprosium particles were isothermally oxidized from 500 to 1000 °C in N{sub 2}–(2%, 20%, and 50%) O{sub 2} and Ar–20% O{sub 2} using simultaneous thermal analysis techniques. Two distinct oxidation regions were identified at each isothermal temperature in each oxidizing atmosphere. Initially, the oxidation kinetics are very fast until the reaction enters a slower, intermediate region of oxidation. The two regions are defined and the kinetics of each are assessed to show an apparent activation energy of 8–25 kJ/mol in the initial region and 80–95 kJ/mol in the intermediate oxidation reaction region. The effects of varying the oxygen partial pressure on the reaction rate constant are used to show that dysprosium oxide (Dy{sub 2}O{sub 3}) generally acts as a p-type semiconductor in both regions of oxidation (with an exception above 750 °C in the intermediate region)

  14. Can a dysprosium shortage threaten green energy technologies?

    NARCIS (Netherlands)

    Hoenderdaal, S.; Tercero Espinoza, L.; Marschneider-Weidemann, F.; Crijns - Graus, Wina|info:eu-repo/dai/nl/308005015

    2013-01-01

    Dysprosium, one of the various rare earth elements, is currently for more than 99% mined in China. As China is reducing its exports, new mining projects outside of China are needed to sustain supply and meet future demands. Dysprosium is mainly used in permanent magnets to retain the magnet's

  15. Ethanolamine derivatives of dysprosium and holmium

    International Nuclear Information System (INIS)

    Gharia, K.S.; Singh, M.; Mathur, S.; Sankhla, B.S.

    1981-01-01

    The preparation and properties of dysprosium and holmium derivatives of mono-, di- and tri-ethanolamine derivatives are described. Compounds of general formulae: Ln(OPrsup(i)) 2 (mea), Ln(OPrsup(i))(mea) 2 , Ln(mea) 3 , Ln(OPrsup(i))(dea), Ln 2 (dea) 3 , Ln(dea)(deaH) and Ln(tea) (where Ln = Dy or Ho and mea, dea and tea are the anions of respective ethanolamine) were obtained and characterized by elemental analysis and IR spectra. (author)

  16. Synthesis and characterization of tetraphenylporphyrinate of dysprosium route dysprosium acetylacetonate.; Sintesis y caracterizacion de un porfirinato de disprosio via acetilacetonato de disprosio.

    Energy Technology Data Exchange (ETDEWEB)

    Martinez M, V

    1993-12-31

    Dysprosium bis (tetraphenylporphyrinate) and bis (dysprosium) Tris (tetraphenylporphyrinate) were synthesized from dysprosium tetraphenylporphyrinate prepared in situ, and characterized by IR, UV-vis, TGA, DTA, EPR and magnetic susceptibility measurements. The double decker compound was obtained by direct oxidation of the HDy(TPP){sub 2} intermediate. The existence of the radical anion, (TPP){sup -} , in the double decker product was conformed by EPR spectrometry. Dysprosium monoporphyrinate was isolated and characterized by the same techniques. (Author).

  17. Nuclear statistics of dysprosium resonance parameters in the energy range 10 - 1000 eV

    International Nuclear Information System (INIS)

    Shin, S. G.; Kye, Y. U.; Cho, M. H.; Kim, G. N.; Namkung, W.; Lee, M. W.; Kang, Y. R.; Roe, T. I.

    2016-01-01

    A resonance parameter analysis is often performed in the Resolved Resonance Region (RRR) in order to estimate the average level spacing, distribution of the reduced widths and so on. Neutron Capture experiments on dysprosium isotopes were performed at the electron linear accelerator (LINAC) facility of the Rensselear Polytechnic Institute (RPI) in the neutron energy region from 10 eV to 1 keV. The following nuclear statistics of the resonance parameters will be discussed in this paper. The D 0 for 161 Dy and 163 Dy were judged to be constant up to 120.6 and 163.9 eV, respectively. It was assumed that the D 0 of 162 Dy and 164 Dy is constant up to 1000 eV because they have few resonances. The results were compared with the values from Reference 11 as shown in Figure 1. Statistical distributions of reduced neutron were investigated for the three isotopes in the region from 0 to 1000 eV; 161 Dy, 162 Dy, and 163 Dy, but not for 164 Dy because of a few number of resonances. The reduced neutron widths Γ n 0 were divided by the unweighted average reduced neutron width < Γ n 0 > for each isotope. A cumulative distribution of these unitless ratios is compared with the integral of the Porter-Thomas distribution (χ 2 distribution with one degree of freedom). The results agree reasonably with the Porter Thomas distributions.

  18. Method for producing dysprosium-iron-boron alloy powder

    International Nuclear Information System (INIS)

    Camp, F.E.; Wooden, S.A.

    1989-01-01

    A method for producing a dysprosium-iron alloy adapted for use in the manufacture of rare-earth element containing, iron-boron permanent magnets, the method including providing a particle mixture comprising dysprosium oxide, iron and calcium, compacting the particle mixture to produce a consolidated article, heating the article for a time at temperature to form a metallic compound comprising dysprosium and iron and to form calcium oxide, producing a particle mass of -35 mesh from the compact, washing the particle mass with water at a temperature no greater than 10 0 C to react to the calcium and to the calcium oxide therewith to form a calcium hydroxide, while preventing oxidation of the particle mass, and removing the calcium hydroxide from the particle mass

  19. Synthesis and thermal decomposition study of dysprosium trifluoroacetate

    DEFF Research Database (Denmark)

    Opata, Y. A.; Grivel, J.-C.

    2018-01-01

    A study of the thermal decomposition process of dysprosium trifluoroacetate hydrate under flowing argon is presented. Thermogravimetry, differential thermal analysis, evolved gas analysis and ex-situ x-ray diffraction techniques have been employed in the investigation. Three main stages were...

  20. The decay of hot dysprosium nuclei

    International Nuclear Information System (INIS)

    Atac, A.; Rekstad, J.; Guttormsen, M.; Messelt, S.; Ramsoey, T.; Thorsteinsen, T.F.; Loevhoeiden, G.; Roedland, T.

    1987-03-01

    The γ-decay following the 162,163 Dy( 3 He,αxn) reactions with E 3 He =45 MeV has been studied. Non-statistical γ-radiation with energies of E γ ≅1 MeV and ≅2 MeV is found for various residual nuclei. The properties of these γ-ray bumps depend on the number of emitted neutrons and reveal an odd-even mass dependence. New techniques to extract average neutron energies as a function of excitation energy and of the number of emitted neutrons are employed. The deduced neutron energies are consistent with Fermi-gas model predictions

  1. Magnon contribution to electrical resistance of gadolinium-dysprosium alloy single crystals

    International Nuclear Information System (INIS)

    Nikitin, S.A.; Slobodchikov, S.S.; Solomkin, I.K.

    1978-01-01

    The magnon, phonon and interelectron collision contributions to the electric resistance of single crystals of gadolinium-dysprosium alloys were quantified. A relationship was found to exist between the electric resistance and the variation of the topology of the Fermi surface on melting of gadolinium with dysprosium. It was found that gadolinium-dysprosium alloys, which have no helicoidal magnetic structure in magnetically ordered state, feature a spin-spin helicoidal-type correlations in the paramagnetic field

  2. Compounds of divalent thulium, neodymium, and dysprosium

    International Nuclear Information System (INIS)

    Bochkarev, M.N.; Fedushkin, I.L.; Trifonov, A.A.; Fagin, A.A.; Kirillov, E.N.

    1998-01-01

    Full text: Judging on the Ln(II)/Ln(III) potentials Tm, Nd, and Dy are the first candidates after Sm, Eu, and Yb for the preparation of Ln(II) compounds. The first molecular Tm(II) derivatives, TmI 2 (DME) 3 (I), has been obtained recently by the reduction of TmI 3 with thulium metal in DME (1,2-dimethoxyethane). The tetrahydrofuran (THF) analogue, TmI 2 (THF) 5 , was synthesized similarly. In the case of TmBI 3 and TmCl 3 the same reaction does not occur. The compound I is inert toward naphthalene, anthracene, phenylacetylene, CpH, (Me 3 Si) 2 NH, 2,4,6-t-Bu 3 C 6 H 2 OH, Cp 2 V, Cp 2 Fe, or Cp 3 Er. The reactions of I with PhOH, Ph 3 COH, 3,6-t-Bu 2 C 6 H 2 (OH) 2 -1,2 (Cat), and calixarene (Cal) produce, Ph 3 COTmI 2 (DME) 2 , (Cat)TmI(DME) 2 , and (Cal)TmI, correspondingly. The attempts to use I for preparation of the other Tm(II) complexes failed. In all cases (reactions with C 10 H 8 Li, CpK, [1,3-(Me 3 Si) 2 C 5 H 3 ]MgCl, and [Cp'-SiMe 2 -Ind']K 2 ) the Tm(III) derivatives (respectively, (C 10 H 8 Tm) 2 C 10 H 8 , Cp 3 Tm, [1,3-(Me 3 Si) 2 C 5 H 3 ] 2 TmCl, and Cp'-SiMe 2 -Ind')TmI) were obtained. The new stable Tm(II) complex, PhOTmI(DME) 2 (II), has been synthesized by the reduction of I with potassium metal in DME. The product was isolated as the green crystals with μ eff 4.6 BM. Unlike TmI 3 , NdI 3 and DyI 3 can not be reduced by metallic neodymium, dysprosium or sodium in DME or THF. Re-investigation of the product formed in the reaction of NdCl 3 with a lack of Li and naphthalene which was claimed before as NdCl 2 (THF) 2 has shown that this is a mixture of Nd(III) naphthalene complexes of the type [(NdCl 2 (THF) 2 ]nC 10 H 8 (n = 4- 7) (III). Nevertheless the product may be used instead of NdCl 2 for the preparation of RNdCl 2 type complexes. The reactions of III with t-BuNCH=CHNBu-t (DAD), PhCH=CHCH=CHPh (DBD), and PhCH=CHPh afford (DAD)NdCl 2 (THF) 2 , (DBD)[NdCl 2 (THF) 2 ] 2 , and (PhCHCHPh)[NdCl 2 ] 2 (THF) 3 , respectively. The iodides of Nd

  3. Properties of Polydisperse Tin-doped Dysprosium and Indium Oxides

    Directory of Open Access Journals (Sweden)

    Malinovskaya Tatyana

    2017-01-01

    Full Text Available The results of investigations of the complex permittivity, diffuse-reflectance, and characteristics of crystal lattices of tin-doped indium and dysprosium oxides are presented. Using the methods of spectroscopy and X-ray diffraction analysis, it is shown that doping of indium oxide with tin results in a significant increase of the components of the indium oxide complex permittivity and an appearance of the plasma resonance in its diffuse-reflectance spectra. This indicates the appearance of charge carriers with the concentration of more than 1021 cm−3 in the materials. On the other hand, doping of the dysprosium oxide with the same amount of tin has no effect on its optical and electromagnetic properties.

  4. Charge transfer cross sections for dysprosium and cerium

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, Hajime; Tamura, Koji; Okazaki, Tetsuji; Shibata, Takemasa [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-06-01

    Symmetric resonant charge transfer cross sections between singly ionized ions and the parent atoms were measured for dysprosium and cerium in the impact energy of 200-2000eV. The cross sections were determined from the ratio between the number of ions produced by charge transfer and those in primary ion beam. The primary ion beam was produced by a laser ion source in which their atoms were ionized by laser resonant photo-ionization. The slow ions produced by charge transfer and fast primary ions were detected with Faraday cups. The obtained cross sections were (1.82{+-}0.14) x 10{sup -14} cm{sup 2} for dysprosium and (0.88{+-}0.12) x 10{sup -14} cm{sup 2} for cerium in the above energy range. The difference of these values can mostly be explained by considering the electron configurations of these atoms and ions. (author)

  5. Charge transfer cross sections for dysprosium and cerium

    International Nuclear Information System (INIS)

    Adachi, Hajime; Tamura, Koji; Okazaki, Tetsuji; Shibata, Takemasa

    1998-06-01

    Symmetric resonant charge transfer cross sections between singly ionized ions and the parent atoms were measured for dysprosium and cerium in the impact energy of 200-2000eV. The cross sections were determined from the ratio between the number of ions produced by charge transfer and those in primary ion beam. The primary ion beam was produced by a laser ion source in which their atoms were ionized by laser resonant photo-ionization. The slow ions produced by charge transfer and fast primary ions were detected with Faraday cups. The obtained cross sections were (1.82±0.14) x 10 -14 cm 2 for dysprosium and (0.88±0.12) x 10 -14 cm 2 for cerium in the above energy range. The difference of these values can mostly be explained by considering the electron configurations of these atoms and ions. (author)

  6. The development of dysprosium-165 hydroxide macroaggregates for radiation synovectomy

    International Nuclear Information System (INIS)

    McLaren, A.B.; Hetherington, E.L.R.; Maddalena, D.J.; Snowden, G.M.

    1988-06-01

    The development of a dysprosium-165 product, Dy-HMA, which is suitable for the radiation synovectomy of arthritic joints is described. Dysprosium-165 is a short-lived (t 1/2 = 139 min) beta-emitter produced by the neutron irradiation of natural dysprosium. Dy-HMA is a suspension of macroaggregated hydroxide particles in saline with the majority of particles in the 3-5 μm range. Studies in rabbits have demonstrated minimal leakage following the intra-articular injection of a knee joint. At 24 hours, the accumulation in the liver is about 0.003% of the injected dose and there is considerably less in other organs and tissue. The use of Dy-HMA has considerable advantages over the presently used yttrium-90 products. The undesired leakage to and subsequent irradiation of other organs is considerably reduced. The period of hospitalisation is reduced from four days to one and the production of 165 Dy in Australia will overcome the difficulties of supply 90 Y from overseas. 21 refs., 1 fig., 18 tabs

  7. Proton NMR relaxivity of blood samples in the presence of some gadolinium and dysprosium compounds

    International Nuclear Information System (INIS)

    Coroiu, I.; Darabont, Al.; Bogdan, M.

    1999-01-01

    The use of some new compounds in MRI tissue and blood characterisation based on nuclear spin relaxation time measurements cannot be sustained until the molecular sources of these variations are understood. Tissues and blood are complex molecular systems with complex NMR properties. A better comprehension of the molecular basis of relaxation offers the possibility to predict the changes expected for a given pathology. The purpose of this contribution is to evidence the different relaxation characteristics of some gadolinium and dysprosium compounds in the presence and absence of the blood and to give a possible explanation about the molecular processes that cause occurrence of changes. Some gadolinium and dysprosium compounds such as: Gd-CIT (gadolinium citrate), Dy-DTPA (DTPA-diethylenetriamine pentaacetic acid), iron oxide - gadolinium oxide (or dysprosium oxide)- dextran complexes were prepared. The longitudinal T 1 -1 and transverse T 2 -1 'relaxation rates' measurements have been carried out as a function of molar concentrations. All measurements have been made at room temperature (about 25 deg.C) and the proton Larmor frequency ν o = 90 MHz. The pulsed NMR spectrometer utilised was a commercial Bruker SXP4/100 spectrometer. Transverse relaxation rate measurements have been made using the Carr-Purcell method, while longitudinal relaxation rate measurements using the inversion recovery pulse sequence, 180 angle-τ-90 angle. The accuracy was about 2-3% for the longitudinal relaxation rates and about 5-7% for the transverse relaxation rates. R 1 and R 2 relaxivities, in mM -1 s -1 were determined from the least square determination of the slopes of plots 1/T 1,2 versus compound molar concentration, using at least five independent measurements at several concentrations between 0 and 2 mM. Increased R 2 relaxivity observed for dysprosium compounds in the blood presence can be explained by PRE effect. The largest gain in R 2 relaxivity seems to imply a noncovalent

  8. Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

    International Nuclear Information System (INIS)

    Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

    2015-01-01

    Undoped and dysprosium doped lithium borate glass system with empirical formula (70–x) B 2 O 3 –30 Li 2 O–(x) Dy 2 O 3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5–5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy 2 O 3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD). - Highlights: • TL response of undoped and dysprosium doped lithium borate glass subjected to 6 MV photons irradiation at low dose range. • TL linear response of dysprosium doped lithium borate glass. • The sensitivity of dysprosium doped lithium borate glass is approximately 93 times higher than undoped glass

  9. Elevated temperature study of Nd-Fe-B--based magnets with cobalt and dysprosium additions

    International Nuclear Information System (INIS)

    Gauder, D.R.; Froning, M.H.; White, R.J.; Ray, A.E.

    1988-01-01

    This paper discusses the elevated temperature performance of Nd-Fe-B magnets containing 0--15 wt. % cobalt substitutions for iron and 0--10 wt. % dysprosium substitutions for neodymium. Test samples were prepared using conventional powder metallurgy techniques. Elevated temperature hysteresis loop and open-circuit measurements were performed on the samples to investigate irreversible losses and long term aging losses at 150 0 C. Magnets with high amounts of both cobalt and dysprosium exhibited lower losses of coercivity and magnetization. Dysprosium had more influence on the elevated temperature performance of the material than did cobalt

  10. Study on the electrochemical of the metal deposition from ionic liquids for lithium, titanium and dysprosium

    International Nuclear Information System (INIS)

    Berger, Claudia A.

    2017-01-01

    The thesis was aimed to the characterization of electrochemically deposited film of lithium, titanium and dysprosium on Au(111) from different ionic liquids, finally dysprosium on neodymium-iron-boron magnate for industrial applications. The investigation of the deposits were performed using cyclic voltametry, in-situ scanning tunneling microscopy, electrochemical quartz microbalance, XPS and Auger electron spectroscopy. The sample preparation is described in detail. The deposition rate showed a significant temperature dependence.

  11. A terminal fluoride ligand generates axial magnetic anisotropy in dysprosium complexes

    Energy Technology Data Exchange (ETDEWEB)

    Norel, Lucie [Department of Chemistry, University of California, Berkeley, CA (United States); Univ Rennes, CNRS, ISCR (Institut des Sciences Chimiques de Rennes) - UMR 6226, Rennes (France); Darago, Lucy E.; Chakarawet, Khetpakorn; Gonzalez, Miguel I.; Olshansky, Jacob H.; Long, Jeffrey R. [Department of Chemistry, University of California, Berkeley, CA (United States); Le Guennic, Boris; Rigaut, Stephane [Univ Rennes, CNRS, ISCR (Institut des Sciences Chimiques de Rennes) - UMR 6226, Rennes (France)

    2018-02-12

    The first dysprosium complexes with a terminal fluoride ligand are obtained as air-stable compounds. The strong, highly electrostatic dysprosium-fluoride bond generates a large axial crystal-field splitting of the J=15/2 ground state, as evidenced by high-resolution luminescence spectroscopy and correlated with the single-molecule magnet behavior through experimental magnetic susceptibility data and ab initio calculations. (copyright 2018 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  12. Terbium and dysprosium complexes luminescence at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Meshkova, S B; Kravchenko, T B; Kononenko, L.I.; Poluehktov, N S [AN Ukrainskoj SSR, Odessa. Fiziko-Khimicheskij Inst.

    1979-01-01

    The variation is studied of the luminescence intensity of terbium and dysprosium complexes used in the analysis as solutions are cooled down to the liquid nitrogen temperature. Three groups of methods have been studied: observation of fluorescence of aqueous solutions, precipitate and extract suspensions in organic solvents. The brightest luminescence and greatest increase in luminescence intensity are observed at freezing of complex solvents with 1,2-dioxybenzene-3,5-disulfonic acid (DBSA) and iminodiacetic acid (IDA) and DBSA+EDTA, as well as in the case of benzene extracting of complexes with phenanthroline and salicylic acid. Otherwise the intensity increases 2-14-fold and for the complex of terbium with acetoacetic ester 36-fold.

  13. Dysprosium (holmium) determination in the presence of erbium and dysprosium (holmium, erbium) determination in the presence of cerium

    International Nuclear Information System (INIS)

    Tolubara, A.I.; Kochubej, A.I.; Usatenko, Yu.I.

    1978-01-01

    Effect of salicylic acid upon complex formation in the systems REE - boronsulfoalizarinate, REE - oxine and REE - boronsulfoalizarinate - oxine is investigated. Comparison of optical characteristics of the above systems in the absence and in the presence of salicylic acid is carried out. It is established that in all the cases the effect of salicylic acid depends both on the nature of REE and the ratio of all the components of the system. Under certain conditions the given dependence is observed only for erbium complexes. Extraction-photometric methods of dysprosium and holmium determination in the presence of equal erbium amounts, as well as holmium and erbium determination in the presence of cerium equal amounts is developed

  14. Dysprosium (holmium) determination in the presence of erbium and dysprosium (holmium, erbium) determination in the presence of cerium

    Energy Technology Data Exchange (ETDEWEB)

    Tolubara, A I; Kochubei, A I; Usatenko, Yu I

    1978-01-01

    Effect of salicylic acid upon complex formation in the systems REE - boronsulfoalizarinate, REE - oxine and REE - boronsulfoalizarinate - oxine is investigated. Comparison of optical characteristics of the above systems in the absence and in the presence of salicylic acid is carried out. It is established that in all the cases the effect of salicylic acid depends both on the nature of REE and the ratio of all the components of the system. Under certain conditions the given dependence is observed only for erbium complexes. Extraction-photometric methods of dysprosium and holmium determination in the presence of equal erbium amounts, as well as holmium and erbium determination in the presence of cerium equal amounts is developed.

  15. Low Field Magnetic and Thermal Hysteresis in Antiferromagnetic Dysprosium

    Directory of Open Access Journals (Sweden)

    Iuliia Liubimova

    2017-06-01

    Full Text Available Magnetic and thermal hysteresis (difference in magnetic properties on cooling and heating have been studied in polycrystalline Dy (dysprosium between 80 and 250 K using measurements of the reversible Villari effect and alternating current (AC susceptibility. We argue that measurement of the reversible Villari effect in the antiferromagnetic phase is a more sensitive method to detect magnetic hysteresis than the registration of conventional B(H loops. We found that the Villari point, recently reported in the antiferromagnetic phase of Dy at 166 K, controls the essential features of magnetic hysteresis and AC susceptibility on heating from the ferromagnetic state: (i thermal hysteresis in AC susceptibility and in the reversible Villari effect disappears abruptly at the temperature of the Villari point; (ii the imaginary part of AC susceptibility is strongly frequency dependent, but only up to the temperature of the Villari point; (iii the imaginary part of the susceptibility drops sharply also at the Villari point. We attribute these effects observed at the Villari point to the disappearance of the residual ferromagnetic phase. The strong influence of the Villari point on several magnetic properties allows this temperature to be ranked almost as important as the Curie and Néel temperatures in Dy and likely also for other rare earth elements and their alloys.

  16. Kinetics of the nitridation of dysprosium during mechanochemical processing

    Energy Technology Data Exchange (ETDEWEB)

    Alanko, Gordon A.; Osterberg, Daniel D.; Jaques, Brian J. [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Hurley, Michael F. [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Boulevard, Idaho Falls, ID 83401 (United States); Butt, Darryl P., E-mail: darrylbutt@boisestate.edu [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Boulevard, Idaho Falls, ID 83401 (United States)

    2015-01-25

    Highlights: • DyN was mechanochemically synthesized by milling pure metal under nitrogen. • Temperature and pressure were monitored to investigate reaction progress. • The effects of metal adhered to media on the impact energetics was measured. • The reactive milling kinetics are described in terms of reactive surface formation. - Abstract: Dysprosium nitride was synthesized by the reactive milling of the rare earth metal under 400 kPa nitrogen gas in a planetary ball mill. The nitrogen consumption rate was calculated from in situ temperature and pressure measurements to find the reaction extent as a function of milling time at milling speeds from 350 to 650 rpm. The results are analyzed in terms of a fundamental milling dynamics model in which the input milling energy is the primary driving force for reaction and the rate limiting step of the nitridation kinetics is the formation of chemically active surfaces. The model differs from traditional gas–solid reactions which are often limited by diffusion of a species through a surface layer or by dissociation of the gas molecule. These results give fresh insight into reactive gas–solid milling kinetics.

  17. Systems of pyridine, piperidine, piperazine, morpholine hydrochlorides-terbium (dysprosium) chloride-water

    International Nuclear Information System (INIS)

    Gajfutdinova, R.K.; Sharafutdinova, A.A.; Murinov, Yu.I.

    1988-01-01

    The isothermal cross section method at 25 and 50 deg C is applied to study pyridine hydrochloride-terbium chloride-water (1) piperidine hydrochloride-dysprosium chloride-water (2), piperazine dihydrochloride-dysprosium chloride-water (3) and morpholine hydrochloride-terbium chloride (4) systems. Solubility isotherma prove the formation of incongruently soluble compound of the TbCl 3 x6C 5 H 5 NxHCl composition systems (1). The individuality of the new solid phase is proved by the chemical and DTA methods. Systems (2-4) are of a simple eutonic type

  18. Exploration of dysprosium: the most critical element for Japan

    Science.gov (United States)

    Watanabe, Y.

    2012-04-01

    Dysprosium (Dy), one of the heavy rare earth elements, is used mainly as an additive for NdFeB permanent magnets which are installed in various modern industrial products such as voice coil motors in computers, factory automation machinery, hybrid and electric vehicles, home electronics, and wind turbine, to improve heat resistance of the magnets. Dy has been produced about 2,000t per year from the ores from ion adsorption type deposits in southern China. However, the produced amount of Dy was significantly reduced in 2011 in China due to reservation of heavy rare earth resources and protection of natural environment, resulting in soaring of Dy price in the world. In order to respond the increasing demand of Dy, unconventional supply sources are inevitably developed, in addition to heavy rare earth enriched ion adsorption type deposits outside China. Heavy rare earth elements including Dy are dominantly hosted in xenotime, fergusonite, zircon, eudialyte, keiviite, kainosite, iimoriite, etc. Concentration of xenotime is found in placer deposits in Malaysia and India, hydrothermal deposits associated with unconformity-type uranium mineralization (Athabasca basin in Canada, Western Australia), iron-oxide fluorite mineralization (South Africa) and Sn-bearing alkaline granite (Brazil). Zircon and fergusontie concentration is found as igneous and hydrothermal products in peralkaline syenite, alkaline granite and pegmatite (e.g., Nechalacho in Canada). Eudialyte concentration is found in some peralkaline syenite bodies in Greenland, Canada, Sweden and Russia. Among these sources, large Dy resources are estimated in the deposits hosted in peralkaline rocks (Nechalacho: 79,000t, Kvanefjeld: 49,000t, Norra Karr: 15,700t, etc.) compared to the present demand of Dy. Thus, Dy will be supplied from the deposits associated with peralkaline and alkaline deposits in future instead of ion adsorption type deposits in southern China.

  19. 25 CFR 162.606 - Advertisement.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Advertisement. 162.606 Section 162.606 Indians BUREAU OF... § 162.606 Advertisement. Except as otherwise provided in this part, prior to granting a lease or permit.... Advertisements will call for sealed bids and will not offer preference rights. ...

  20. 29 CFR 1915.162 - Ship's boilers.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Ship's boilers. 1915.162 Section 1915.162 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Ship's Machinery and Piping Systems § 1915.162 Ship's boilers. (a) Before...

  1. 49 CFR 176.162 - Security.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Security. 176.162 Section 176.162 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION... Class 1 (Explosive) Materials Precautions During Loading and Unloading § 176.162 Security. A responsible...

  2. 29 CFR 500.162 - Reports.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Reports. 500.162 Section 500.162 Labor Regulations Relating... AGRICULTURAL WORKER PROTECTION Enforcement Agreements with Federal and State Agencies § 500.162 Reports. The Secretary shall require such reports as he deems necessary of activities conducted pursuant to State plans...

  3. 7 CFR 956.162 - Container markings.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Container markings. 956.162 Section 956.162... WALLA VALLEY OF SOUTHEAST WASHINGTON AND NORTHEAST OREGON Rules and Regulations § 956.162 Container markings. Effective April 15, 1997, no handler shall ship any container of Walla Walla Sweet Onions except...

  4. Dosimetric properties of dysprosium doped lithium borate glass irradiated by 6 MV photons

    Science.gov (United States)

    Ab Rasid, A.; Wagiran, H.; Hashim, S.; Ibrahim, Z.; Ali, H.

    2015-07-01

    Undoped and dysprosium doped lithium borate glass system with empirical formula (70-x) B2O3-30 Li2O-(x) Dy2O3 (x=0.1, 0.3, 0.5, 0.7, 1.0 mol%) were prepared using the melt-quenching technique. The dosimetric measurements were performed by irradiating the samples to 6 MV photon beam using linear accelerator (LINAC) over a dose range of 0.5-5.0 Gy. The glass series of dysprosium doped lithium borate glass produced the best thermoluminescence (TL) glow curve with the highest intensity peak from sample with 1.0 mol% Dy2O3 concentration. Minimum detectable dose was detected at 2.24 mGy, good linearity of regression coefficient, high reproducibility and high sensitivity compared to the undoped glass are from 1.0 mol% dysprosium doped lithium borate glass. The results indicated that the series of dysprosium doped lithium glasses have a great potential to be considered as a thermoluminescence dosimetry (TLD).

  5. In situ characterization of the nitridation of dysprosium during mechanochemical processing

    Energy Technology Data Exchange (ETDEWEB)

    Jaques, Brian J.; Osterberg, Daniel D.; Alanko, Gordon A.; Tamrakar, Sumit; Smith, Cole R.; Hurley, Michael F.; Butt, Darryl P., E-mail: DarrylButt@BoiseState.edu

    2015-01-15

    Highlights: • A nitridation reaction in a high energy planetary ball mill was monitored in situ. • Dysprosium mononitride was synthesized from Dy at low temperatures in short times. • Ideal gas law and in situ temperature and pressure used to assess reaction extent. • It is proposed that reaction rate is proportional to the creation of new surface. - Abstract: Processing of advanced nitride ceramics traditionally requires long durations at high temperatures and, in some cases, in hazardous atmospheres. In this study, dysprosium mononitride (DyN) was rapidly formed from elemental dysprosium in a closed system at ambient temperatures. An experimental procedure was developed to quantify the progress of the nitridation reaction during mechanochemical processing in a high energy planetary ball mill (HEBM) as a function of milling time and intensity using in situ temperature and pressure measurements, SEM, XRD, and particle size analysis. No intermediate phases were formed. It was found that the creation of fresh dysprosium surfaces dictates the rate of the nitridation reaction, which is a function of milling intensity and the number of milling media. These results show clearly that high purity nitrides can be synthesized with short processing times at low temperatures in a closed system requiring a relatively small processing footprint.

  6. A model for additive transport in metal halide lamps containing mercury and dysprosium tri-iodide

    NARCIS (Netherlands)

    Beks, M.L.; Haverlag, M.; Mullen, van der J.J.A.M.

    2008-01-01

    The distribution of additives in a metal halide lamp is examined through numerical modelling. A model for a lamp containing sodium iodide additives has been modified to study a discharge containing dysprosium tri-iodide salts. To study the complex chemistry the method of Gibbs minimization is used

  7. Neutronography of an intermediate phase in dysprosium near the Neel point

    Energy Technology Data Exchange (ETDEWEB)

    Bessergenev, V G; Gogava, V V; Kovalevskaya, Yu A; Mandzhavidze, A G; Fedorov, V M; Shilo, S I

    1985-11-25

    Neutronographical study of dysprosium magnetic structure near the point of magnetic disordering depending on thermal prehistory of the sample is carried out. Intermediate vortex phase transformed then into the helical one is shown to occur from the paramagnetic phase under cooling.

  8. Synthesis and X-ray structure of the dysprosium(III) complex derived ...

    African Journals Online (AJOL)

    Synthesis and X-ray structure of the dysprosium(III) complex derived from the ligand 5-chloro-1 ... Bulletin of the Chemical Society of Ethiopia ... synthesized and its crystal structure determined by single X-ray diffraction at room temperature.

  9. Dysprosium-containing layered double hydroxides nanoparticles intercalated with biologically active species as an approach for theranostic systems

    KAUST Repository

    Arratia-Quijada, Jenny

    2015-10-23

    A layered double hydroxide structure including dysprosium cations was prepared by co-precipitation. The nanoparticles showed a linear relationship with the reciprocal relaxation spin-lattice (T1) time of water protons which is reflected as contrast in aqueous suspensions analyzed by magnetic resonance imaging. The interlayer space of dysprosium containing LDH was successfully intercalated with folate, ibuprofen and gallate ions, which are key molecules for recognition of some cancer cells and treatment of diseases. The paramagnetic property of the dysprosium-containing LDH detected in this work beside the ability to transport drugs open up the opportunity to design theranostic materials in a single crystal phase with nanometric dimensions.

  10. Dysprosium-containing layered double hydroxides nanoparticles intercalated with biologically active species as an approach for theranostic systems

    KAUST Repository

    Arratia-Quijada, Jenny; Sá nchez Jimé nez, Cecilia; Gurinov, Andrei; Pé rez Centeno, Armando; Ceja Andrade, Israel; Carbajal Arí zaga, Gregorio Guadalupe

    2015-01-01

    A layered double hydroxide structure including dysprosium cations was prepared by co-precipitation. The nanoparticles showed a linear relationship with the reciprocal relaxation spin-lattice (T1) time of water protons which is reflected as contrast in aqueous suspensions analyzed by magnetic resonance imaging. The interlayer space of dysprosium containing LDH was successfully intercalated with folate, ibuprofen and gallate ions, which are key molecules for recognition of some cancer cells and treatment of diseases. The paramagnetic property of the dysprosium-containing LDH detected in this work beside the ability to transport drugs open up the opportunity to design theranostic materials in a single crystal phase with nanometric dimensions.

  11. Dysprosium complexes with the tetraphenylporphyrin macrocyclic ligand; Complejos de disprosio con el ligante macrociclico tetrafenilporfirina

    Energy Technology Data Exchange (ETDEWEB)

    Martinez M, V.; Padilla, J.; Ramirez, F.M

    1992-04-15

    In this report, the results obtained on the synthesis, characterization and study of the chemical behavior of dysprosium complex with the acetylacetone chelating agent (Hacac) and the tetraphenylporphyrin macrocyclic ligand (H{sub 2}TFP) are given. Based on the literature but according to our necessities and interest, the appropriate methodology settled down from the synthesis of prime matters until the obtaining and characterization of the products. The acetyl acetonate complex was obtained of mono hydrated dysprosium [Dy(acac){sub 3}. H{sub 2}0] and trihydrated [Dy(acac){sub 3} .3 H{sub 2}0], the mono tetra phenyl porphyrinate [Dy(TFP)(acac). 2 ac] the double sandwich of the dysprosium porphyrinate [Dy(TFP){sub 2}] and the triple sandwich of the dysprosium porphyrinate [Dy(TFP){sub 3}. 2 TCB] (TCB = trichlorobenzene). Its were characterized by their melting points, solubility, IR, UV, TGA and DTA both first and besides the techniques already mentioned for NMR'H, RPE and Magnetic susceptibility the three last complexes. From the spectroscopic point of view, IR and RPE its suggested the existence of a complex of inverse mixed valence [Dy(TFP){sup 2-} (TFP) {sup 1-}] for the Dy(TFP){sub 2} as a result of the existence of the free radical (TFP' {sup 1-} and that it was not in none of the other porphyrin compounds. In the NMR'H spectra of the compounds were not observed signals in the region from 0 to 10 ppm that which shows that the dysprosium complexes in special those of the porphyrin type are highly paramagnetic and its could be used as displacement reagents, creators of images and contrast agents of great utility in these days in studies of NMR, technique today by today used in medical diagnoses. (Author)

  12. Dysprosium complexes with the tetraphenylporphyrin macrocyclic ligand; Complejos de disprosio con el ligante macrociclico tetrafenilporfirina

    Energy Technology Data Exchange (ETDEWEB)

    Martinez M, V; Padilla, J; Ramirez, F M

    1992-04-15

    In this report, the results obtained on the synthesis, characterization and study of the chemical behavior of dysprosium complex with the acetylacetone chelating agent (Hacac) and the tetraphenylporphyrin macrocyclic ligand (H{sub 2}TFP) are given. Based on the literature but according to our necessities and interest, the appropriate methodology settled down from the synthesis of prime matters until the obtaining and characterization of the products. The acetyl acetonate complex was obtained of mono hydrated dysprosium [Dy(acac){sub 3}. H{sub 2}0] and trihydrated [Dy(acac){sub 3} .3 H{sub 2}0], the mono tetra phenyl porphyrinate [Dy(TFP)(acac). 2 ac] the double sandwich of the dysprosium porphyrinate [Dy(TFP){sub 2}] and the triple sandwich of the dysprosium porphyrinate [Dy(TFP){sub 3}. 2 TCB] (TCB = trichlorobenzene). Its were characterized by their melting points, solubility, IR, UV, TGA and DTA both first and besides the techniques already mentioned for NMR'H, RPE and Magnetic susceptibility the three last complexes. From the spectroscopic point of view, IR and RPE its suggested the existence of a complex of inverse mixed valence [Dy(TFP){sup 2-} (TFP) {sup 1-}] for the Dy(TFP){sub 2} as a result of the existence of the free radical (TFP' {sup 1-} and that it was not in none of the other porphyrin compounds. In the NMR'H spectra of the compounds were not observed signals in the region from 0 to 10 ppm that which shows that the dysprosium complexes in special those of the porphyrin type are highly paramagnetic and its could be used as displacement reagents, creators of images and contrast agents of great utility in these days in studies of NMR, technique today by today used in medical diagnoses. (Author)

  13. Dysprosium, the balance problem, and wind power technology

    International Nuclear Information System (INIS)

    Elshkaki, Ayman; Graedel, T.E.

    2014-01-01

    Highlights: • We investigate the impacts of the increasing market share of wind power on the demand and supply of REE. • The analysis is carried out using a dynamic material flow and stock model and three scenarios for Dy supply. • The supply of Dy from all deposits will likely lead to an oversupply of the total REEs, Nd, La, Ce and Y. • The supply of Dy from critical REE or Dy rich deposits will likely lead to an oversupply of Ce and Y only. • Large quantities of thorium will be co-produced as a result of Dy demand that needs to be managed carefully. - Abstract: Wind power technology is one of the cleanest electricity generation technologies that are expected to have a substantial share in the future electricity mix. Nonetheless, the expected increase in the market share of wind technology has led to an increasing concern of the availability, production capacity and geographical concentration of the metals required for the technology, especially the rear earth elements (REE) neodymium (Nd) and the far less abundant dysprosium (Dy), and the impacts associated with their production. Moreover, Nd and Dy are coproduced with other rare earth metals mainly from iron, titanium, zirconium, and thorium deposits. Consequently, an increase in the demand for Nd and Dy in wind power technology and in their traditional applications may lead to an increase in the production of the host metals and other companion REE, with possible implications on their supply and demand. In this regard, we have used a dynamic material flow and stock model to study the impacts of the increasing demand for Nd and Dy on the supply and demand of the host metals and other companion REE. In one scenario, when the supply of Dy is covered by all current and expected producing deposits, the increase in the demand for Dy leads to an oversupply of 255 Gg of total REE and an oversupply of the coproduced REE Nd, La, Ce and Y. In the second and third scenarios, however, when the supply of Dy is

  14. Dysprosium-containing layered double hydroxides nanoparticles intercalated with biologically active species as an approach for theranostic systems

    Energy Technology Data Exchange (ETDEWEB)

    Arratia-Quijada, Jenny [Departamento de Ciencias de la Salud, Centro Universitario Tonalá, Universidad de Guadalajara, Av. Nuevo Periférico No. 555, C.P. 48525, Tonalá, Jalisco (Mexico); Sánchez Jiménez, Cecilia [Departamento de Química, Universidad de Guadalajara, Boulevard Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico); Gurinov, Andrey [Research Resources Center for Magnetic Resonance, St. Petersburg State University, Universitetskiy pr. 26, 198504 St. Petersburg (Russian Federation); NMR Core Lab, King Abdullah University of Science and Technology, Thuwal 23955-6900 (Saudi Arabia); Pérez Centeno, Armando; Ceja Andrade, Israel [Departamento de Física, Universidad de Guadalajara, Boulevard Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico); Carbajal Arízaga, Gregorio Guadalupe, E-mail: gregoriocarbajal@yahoo.com.mx [Departamento de Química, Universidad de Guadalajara, Boulevard Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico)

    2016-01-15

    Graphical abstract: - Highlights: • LDH structure including dysprosium was prepared by co-precipitation. • LDH was capable to produce contrast in the T1 mode of MRI. • LDH were intercalated with folate, ibuprofen and gallate ions. - Abstract: A layered double hydroxide structure including dysprosium cations was prepared by co-precipitation. The nanoparticles showed a linear relationship with the reciprocal relaxation spin-lattice (T1) time of water protons which is reflected as contrast in aqueous suspensions analyzed by magnetic resonance imaging. The interlayer space of dysprosium containing LDH was successfully intercalated with folate, ibuprofen and gallate ions, which are key molecules for recognition of some cancer cells and treatment of diseases. The paramagnetic property of the dysprosium-containing LDH detected in this work beside the ability to transport drugs open up the opportunity to design theranostic materials in a single crystal phase with nanometric dimensions.

  15. Dysprosium-containing layered double hydroxides nanoparticles intercalated with biologically active species as an approach for theranostic systems

    International Nuclear Information System (INIS)

    Arratia-Quijada, Jenny; Sánchez Jiménez, Cecilia; Gurinov, Andrey; Pérez Centeno, Armando; Ceja Andrade, Israel; Carbajal Arízaga, Gregorio Guadalupe

    2016-01-01

    Graphical abstract: - Highlights: • LDH structure including dysprosium was prepared by co-precipitation. • LDH was capable to produce contrast in the T1 mode of MRI. • LDH were intercalated with folate, ibuprofen and gallate ions. - Abstract: A layered double hydroxide structure including dysprosium cations was prepared by co-precipitation. The nanoparticles showed a linear relationship with the reciprocal relaxation spin-lattice (T1) time of water protons which is reflected as contrast in aqueous suspensions analyzed by magnetic resonance imaging. The interlayer space of dysprosium containing LDH was successfully intercalated with folate, ibuprofen and gallate ions, which are key molecules for recognition of some cancer cells and treatment of diseases. The paramagnetic property of the dysprosium-containing LDH detected in this work beside the ability to transport drugs open up the opportunity to design theranostic materials in a single crystal phase with nanometric dimensions.

  16. Dysprosium-Catalyzed Growth of Single-Walled Carbon Nanotube Arrays on Substrates

    Directory of Open Access Journals (Sweden)

    Qian Yong

    2009-01-01

    Full Text Available Abstract In this letter, we report that dysprosium is an effective catalyst for single-walled carbon nanotubes (SWNTs growth via a chemical vapor deposition (CVD process for the first time. Horizontally superlong well-oriented SWNT arrays on SiO2/Si wafer can be fabricated by EtOH-CVD under suitable conditions. The structure and properties are characterized by scanning electron microscopy, transition electron microscopy, Raman spectroscopy and atomic force microscopy. The results show that the SWNTs from dysprosium have better structural uniformity and better conductivity with fewer defects. This rare earth metal provides not only an alternative catalyst for SWNTs growth, but also a possible method to generate high percentage of superlong semiconducting SWNT arrays for various applications of nanoelectronic device.

  17. Sandwich-type tetrakis(phthalocyaninato) dysprosium-cadmium quadruple-decker SMM.

    Science.gov (United States)

    Wang, Hailong; Qian, Kang; Wang, Kang; Bian, Yongzhong; Jiang, Jianzhuang; Gao, Song

    2011-09-14

    Homoleptic tetrakis[2,3,9,10,16,17,23,24-octa(butyloxy)phthalocyaninato] dysprosium-cadmium quadruple-decker complex 1 was isolated in relatively good yield of 43% from a simple one-pot reaction. This compound represents the first sandwich-type tetrakis(phthalocyaninato) rare earth-cadmium quadruple-decker SMM that has been structurally characterized. This journal is © The Royal Society of Chemistry 2011

  18. {Delta}I = 2 energy staggering in normal deformed dysprosium nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Riley, M.A.; Brown, T.B.; Archer, D.E. [Florida State Univ., Tallahassee, FL (United States)] [and others

    1996-12-31

    Very high spin states (I{ge}50{Dirac_h}) have been observed in {sup 155,156,157}Dy. The long regular band sequences, free from sharp backbending effects, observed in these dysprosium nuclei offer the possibility of investigating the occurence of any {Delta}I = 2 staggering in normal deformed nuclei. Employing the same analysis techniques as used in superdeformed nuclei, certain bands do indeed demonstrate an apparent staggering and this is discussed.

  19. Analysis of the x-ray spectrum emitted by laser-produced plasma of dysprosium

    International Nuclear Information System (INIS)

    Marcus, Gilad; Louzon, Einat; Henis, Zohar; Maman, Shlomo; Mandelbaum, Pinchas

    2007-01-01

    A detailed analysis of the x-ray spectrum (5-10.2 A ring ) emitted by laser-produced plasma of dysprosium (Dy) is given using ab initio calculations with the HULLAC relativistic code and isoelectronic trends. Resonance 3d-4p, 3d-nf (n=4 to 7), 3p-4s, and 3p-4d transitions of Ni I-like Dy XXXIX and neighboring ion satellite transitions (from Dy XXXIV to Dy XL) are identified

  20. Phosphor Dysprosium-Doped Layered Double Hydroxides Exchanged with Different Organic Functional Groups

    Directory of Open Access Journals (Sweden)

    David Ricardo Martínez Vargas

    2013-01-01

    Full Text Available The layers of a Zn/Al layered double hydroxide (LDH were doped with Dy3+ cations. Among some compositions, the Zn2+ : Al3+ : Dy3+ molar ratio equal to 30 : 9 : 1 presented a single crystalline phase. Organic anions with carboxylic, amino, sulfate, or phosphate functional groups were intercalated as single layers between LDH layers as confirmed by X-ray diffraction and infrared spectroscopy. Photoluminescence spectra of the nitrate intercalated LDH showed a wide emission band with strong intensity in the yellow region (around 574 nm, originated due to symmetry distortion of the octahedral coordination in dysprosium centers. Moreover, a broad red band emission was also detected apparently due to the presence of zinc oxide. The distorted symmetry of the dysprosium coordination environment, also confirmed by X-ray photoelectron spectroscopy analysis, was modified after the intercalation with phenyl phosphonate (PP, aspartate (Asp, adipate (Adip, and serinate (Ser anions; the emission as measured from PL spectra of these LDH was more intense in the blue region (ca. 486 nm, thus indicating an increase in symmetry of dysprosium octahedrons. The red emission band from zinc oxide kept the same intensity after intercalation of dodecyl sulfate (DDS. An additional emission of unknown origin at λ = 767 nm was present in all LDHs.

  1. Synovectomy of the rheumatoid knee using intra-articular injection of dysprosium-165-ferric hydroxide macroaggregates

    International Nuclear Information System (INIS)

    Sledge, C.B.; Zuckerman, J.D.; Shortkroff, S.; Zalutsky, M.R.; Venkatesan, P.; Snyder, M.A.; Barrett, W.P.

    1987-01-01

    One hundred and eleven patients who had seropositive rheumatoid arthritis and persistent synovitis of the knee were treated with intra-articular injection of 270 millicuries of dysprosium-165 bound to ferric hydroxide macroaggregates. A two-year follow-up was available for fifty-nine of the treated knees. Thirty-nine had a good result; nine, a fair result; and eleven, a poor result. Of the twenty-five knees that had Stage-I radiographic changes, nineteen had a good result. Of the thirty-four knees that had Stage-II radiographic changes, twenty showed a good result. Systemic spread of the radioactivity from the injected joint was minimum. The mean whole-body dose was calculated to be 0.3 rad and that to the liver twenty-four hours after injection, 3.2 rads. The results indicated that dysprosium-165-ferric hydroxide macroaggregate is an effective agent for performing radiation synovectomy, particularly in knees that have Stage-I radiographic changes. Because of the minimum rate of systemic spread of the dysprosium-165, it offers a definite advantage over agents that previously have been used

  2. 46 CFR 162.039-2 - Classification.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Classification. 162.039-2 Section 162.039-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Classification. (a) Every semiportable fire extinguisher shall be classified as to type and size as specified in...

  3. 46 CFR 162.028-2 - Classification.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Classification. 162.028-2 Section 162.028-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... Classification. (a) Every portable fire extinguisher shall be classified as to type and size as specified in § 76...

  4. 40 CFR 16.2 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Definitions. 16.2 Section 16.2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL IMPLEMENTATION OF PRIVACY ACT OF 1974 § 16... records have the same meanings as specified in 5 U.S.C. 552a. (b) EPA means the Environmental Protection...

  5. 40 CFR 162.151 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Definitions. 162.151 Section 162.151 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS STATE REGISTRATION... registered product. Pest problem means: (1) A pest infestation and its consequences, or (2) Any condition for...

  6. 31 CFR 16.2 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Definitions. 16.2 Section 16.2 Money and Finance: Treasury Office of the Secretary of the Treasury REGULATIONS IMPLEMENTING THE PROGRAM... a position for which the rate of basic pay is not less than the minimum rate of basic pay for grade...

  7. 10 CFR 72.162 - Test control.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Test control. 72.162 Section 72.162 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSING REQUIREMENTS FOR THE INDEPENDENT STORAGE OF SPENT NUCLEAR FUEL... Test control. The licensee, applicant for a license, certificate holder, and applicant for a CoC shall...

  8. 7 CFR 28.162 - Procedure.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Procedure. 28.162 Section 28.162 Agriculture..., TESTING, AND STANDARDS Regulations Under the United States Cotton Standards Act Adjustment of Contract... and in instituting and conducting arbitrations and appeals shall be as prescribed in the articles...

  9. Development and mastering of production of dysprosium hafnate as absorbing material for control rods of promising thermal neutron reactors

    International Nuclear Information System (INIS)

    Zakharov, A.V.; Risovany, V.D.; Muraleva, E.M.; Sokolov, V.F.

    2011-01-01

    The main advantages of dysprosium hafnate as an absorbing material for LWR control rods are the following: -) unlimited radiation resistance; - two absorbing components, Dy and Hf, increasing physical efficiency of the material compared to Dy 2 O 3 -TiO 2 and alloy 80% Ag - 15% In - 5% Cd; -) variability of physical efficiency by changing a composition, but maintaining other performance characteristics of the material; -) high process-ability due to the absence of phase transients and single-phase structure (solid solution); -) production of high density pellets. Lab-scale mastering of dysprosium hafnate pellets production showed a possibility of material synthesis using a solid-phase method, as well as of dysprosium hafnate pellets production by cold pressing and subsequent sintering. Within a whole range of examined compositions (23 mol% - 75 mol% Dy 2 O 3 ), a single-phase material with a highly radiation resistant fluorite-like structure was produced. Experiments on cold pressing and sintering of pellets confirmed a possibility of producing high quality dysprosium hafnate pellets from synthesized powder. A pilot batch of dysprosium hafnate pellets with standard sizes was produced. The standard sizes corresponded to the absorbing elements of the WWER-1000 control rods and met the main requirements to the absorbing element columns. The pilot batch size was approximately 6 kg. Acceptance testing of the pilot batch of dysprosium hafnate pellets was conducted, fulfillment of the requirements of technical conditions was checked and preirradiation properties of the pellets were examined. High quality of the produced pellets was confirmed, thus, demonstrating a real possibility of producing large batches of the dysprosium hafnate pellets. The next step is the production of test absorbing elements and cluster assemblies for the WWER-1000 control rods with their further installation for pilot operation at one of the Russian nuclear power plants

  10. Systematic study on surface and magnetostructural changes in Mn-substituted dysprosium ferrite by hydrothermal method

    Energy Technology Data Exchange (ETDEWEB)

    Rekha, G. [Department of Physics, College of Engineering Guindy, Anna University, Sardar Patel Road, Chennai 600025 (India); Tholkappiyan, R. [Department of Physics, College of Engineering Guindy, Anna University, Sardar Patel Road, Chennai 600025 (India); Department of Physics, College of Science, UAE University, Al-Ain 15551 (United Arab Emirates); Vishista, K., E-mail: raovishista@gmail.com [Department of Physics, College of Engineering Guindy, Anna University, Sardar Patel Road, Chennai 600025 (India); Hamed, Fathalla [Department of Physics, College of Science, UAE University, Al-Ain 15551 (United Arab Emirates)

    2016-11-01

    Highlights: • Garnet type Dy{sub 3}Fe{sub 5-x}Mn{sub x}O{sub 12} (x = 0–0.06) nanoparticles of 88.4–86.8 nm were synthesized by hydrothermal method. • The Dy, Mn, Fe and O elements in the ferrites were confirmed from XPS. • The multiple oxidation states of Fe and Mn ions, bonding energy and cationic distributions of the samples were examined by XPS. • The magnetic property shows ferromagnetic behavior from VSM technique. • The results from these studies are correlated with respect to Mn dopant. - Abstract: Dysprosium iron garnets are of scientific importance because of the wide range of magnetic properties that can be obtained in substituting dysprosium by a rare earth metal. In the present work, the effect of Mn substitution on magnetostructural changes in dysprosium ferrite nanoparticles is studied. Highly crystalline pure and Mn doped dysprosium ferrite nanoparticles were synthesized by hydrothermal method. The samples were calcined at 1100 °C for 2 h in air atmosphere which is followed by characterization using XRD, FT-IR analysis, SEM, XPS and VSM. The average crystallite size of synthesized samples were calculated by X-ray diffraction falls in the range of 88.4–86.8 nm and was found to be in cubic garnet structure. For further investigation of the structure and corresponding changes in the tetrahedral and octahedral stretching vibrational bonds, FT-IR was used. The synthesized samples consist of multiple oxidation (Fe{sup 3+} and Fe{sup 2+}) states for Fe ions and (Mn{sup 3+} and Mn{sup 2+}) Mn ions analyzed in three ways of Fe 2p and Mn 2p spectra from the XPS analysis. With respect to Mn dopant in Dy{sub 3}Fe{sub 5}O{sub 12}, the cationic distributions of elements were discussed from high resolution XPS spectra by peak position and shift, area, width. To find out the porous/void surface morphology of the sample, scanning electron microscopy was used. From XPS analysis, the presence of elements (Dy, Mn, Fe and O) and their composition in the

  11. Synthesis, structural characterization and in vitro testing of dysprosium containing silica particles as potential MRI contrast enhancing agents

    Energy Technology Data Exchange (ETDEWEB)

    Chiriac, L.B.; Trandafir, D.L. [Faculty of Physics & National Magnetic Resonance Center, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania); Interdisciplinary Research Institute on Bio-Nano-Sciences & Faculty of Physics, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania); Turcu, R.V.F. [Faculty of Physics & National Magnetic Resonance Center, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania); Todea, M. [Interdisciplinary Research Institute on Bio-Nano-Sciences & Faculty of Physics, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania); Simon, S., E-mail: simons@phys.ubbcluj.ro [Faculty of Physics & National Magnetic Resonance Center, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania); Interdisciplinary Research Institute on Bio-Nano-Sciences & Faculty of Physics, Babeş-Bolyai University, Cluj-Napoca, RO-400084 (Romania)

    2016-11-01

    Highlights: • Dysprosium containing silica microparticles obtained by freeze and spray drying. • Higher structural units interconnection achieved in freeze vs. spray dried samples. • Dy occurance on the outermost layer of the microparticles evidenced by XPS. • Enhanced MRI contrast observed for freeze dried samples with 5% mol Dy{sub 2}O{sub 3}. - Abstract: The work is focused on synthesis and structural characterization of novel dysprosium-doped silica particles which could be considered as MRI contrast agents. Sol-gel derived silica rich particles obtained via freeze-drying and spray-drying processing methods were structurally characterized by XRD, {sup 29}Si MAS-NMR and XPS methods. The occurrence of dysprosium on the outermost layer of dysprosium containing silica particles was investigated by XPS analysis. The MRI contrast agent characteristics have been tested using RARE-T{sub 1} and RARE-T{sub 2} protocols. The contrast of MRI images delivered by the investigated samples was correlated with their local structure. Dysprosium disposal on microparticles with surface structure characterised by decreased connectivity of the silicate network units favours dark T{sub 2}-weighted MRI contrast properties.

  12. Synthesis, structural characterization and in vitro testing of dysprosium containing silica particles as potential MRI contrast enhancing agents

    International Nuclear Information System (INIS)

    Chiriac, L.B.; Trandafir, D.L.; Turcu, R.V.F.; Todea, M.; Simon, S.

    2016-01-01

    Highlights: • Dysprosium containing silica microparticles obtained by freeze and spray drying. • Higher structural units interconnection achieved in freeze vs. spray dried samples. • Dy occurance on the outermost layer of the microparticles evidenced by XPS. • Enhanced MRI contrast observed for freeze dried samples with 5% mol Dy_2O_3. - Abstract: The work is focused on synthesis and structural characterization of novel dysprosium-doped silica particles which could be considered as MRI contrast agents. Sol-gel derived silica rich particles obtained via freeze-drying and spray-drying processing methods were structurally characterized by XRD, "2"9Si MAS-NMR and XPS methods. The occurrence of dysprosium on the outermost layer of dysprosium containing silica particles was investigated by XPS analysis. The MRI contrast agent characteristics have been tested using RARE-T_1 and RARE-T_2 protocols. The contrast of MRI images delivered by the investigated samples was correlated with their local structure. Dysprosium disposal on microparticles with surface structure characterised by decreased connectivity of the silicate network units favours dark T_2-weighted MRI contrast properties.

  13. Synthesis, characterization and sup 23 Na NMR shift studies of a novel dysprosium(III) crown ether texaphyrin

    Energy Technology Data Exchange (ETDEWEB)

    Sessler, J.L.; Mody, T.D. (Texas Univ., Austin, TX (United States). Dept. of Chemistry); Ramasamy, R.; Sherry, A.D. (Texas Univ., Dallas, TX (United States))

    1992-05-01

    The synthesis and characterization of a novel dysprosium(III) crown-ether texaphyrin (Dy(BCTxp)){sup 2+} is reported. This complex was designed to serve as a ditopic chelate for both dysprosium(III) and sodium cations. {sup 23}Sodium NMR spectroscopic studies indicates that titration of Na{sup +} with increasing concentrations of (Dy(BCTxp)){sup 2+} results in a shift toward higher frequency and gives a net hyperfine shift of 0.86 ppm. Sodium complexation is taking place into the crown subunit in (Dy(BCTxp)){sup 2+} and the degree of complexation is not reduced substantially by the positive charge on the dysprosium(III) portion of this binucleating system.

  14. 32 CFR 162.5 - Responsibilities.

    Science.gov (United States)

    2010-07-01

    ... ENHANCING CAPITAL INVESTMENT (PECI) § 162.5 Responsibilities. (a) The Assistant Secretary of Defense (Force... project applicability when reasonable, applies off-the-shelf technology, and integrates capital investment...

  15. Nuclear spectroscopic studies in 162Yb

    International Nuclear Information System (INIS)

    Behrens, H.

    1980-01-01

    The decay of the highly excited 162 Yb nuclei formed in the reaction 150 Sm( 16 O,4n) 162 Yb to the ground state was studied using different gamma detectors and an electron spectrometer, a so called mini-orange. The isotope 162 Yb was moreover produced and spectroscoped by the beta-decay of 162 Lu. For the identification of decay cascades, which were passed after the fusion, and for the determination of the multipolarity of the contributing energy transitions a series of experiments took place: The excitation functions and the angular distributions of the emitted gamma radiation was measured, the conversion coefficients of important transitions were determined, and coincidence events between two detectors occasionally were registrated and analyzed. In the beta decay measurement an assignment of gamma transitions to 162 Yb followed due to the lifetime, under which they occured. The found states of 162 Yb upto spins of 22 h/2π and excitation energies above 5 MeV belong to five rotational bands. The yrast band shows a weak backbending. Corresponding to their spins and parities the bands can be reduced to intrinsic excitation of two quasineutrons. The analysis of the beta-decay of 162 Lu, which takes place from three states in 162 Lu, leads to the lowest levels of the gamma-vibrational band and the band head of the beta band. The microscopic interpretation of the rotational bands and the description of the backbending behaviour are as the interpretation of the states involved at the beta decay in agreement with experimental and theoretical results for neighbouring ytterbium isotopes. (orig.) [de

  16. Dysprosium disilicide nanostructures on silicon(001) studied by scanning tunneling microscopy and transmission electron microscopy

    International Nuclear Information System (INIS)

    Ye Gangfeng; Nogami, Jun; Crimp, Martin A.

    2006-01-01

    The microstructure of self-assembled dysprosium silicide nanostructures on silicon(001) has been studied by scanning tunneling microscopy and transmission electron microscopy. The studies focused on nanostructures that involve multiple atomic layers of the silicide. Cross-sectional high resolution transmission electron microscopy images and fast Fourier transform analysis showed that both hexagonal and orthorhombic/tetragonal silicide phases were present. Both the magnitude and the anisotropy of lattice mismatch between the silicide and the substrate play roles in the morphology and epitaxial growth of the nanostructures formed

  17. Major conformations of the ligand skeleton of a tetranuclear dysprosium (3) tartrate complex

    International Nuclear Information System (INIS)

    Chevela, V.V.; Semenov, V.Eh.; Bezryadin, S.G.; Savitskaya, T.V.; Kolesar, I.R.; Matveev, S.N.; Shamov, G.A.

    1999-01-01

    By the molecular mechanics method (MIND program, stoichiometry was studied and basic conformations of ligand frame of dysprosium (3) tetranuclear complex bis-(d-tartrato) bis-(l-tartrato)tetradysprosiate (3) - anion Dy 4 (d-L) 2 (l-L) 2 4- (1) (d-H 4 L = d-tartaric acid, l-H 4 L = l - tartaric acid) were revealed. It is shown that theoretically calculated mP τ constants for so-called compact conformations of 1, where tartratoligands are in gosh conformation, agree with experimentally obtained constant of paramagnetic birefringence (mP e ) of complex 1 [ru

  18. Incinerator carryover tests with dysprosium as a stand-in for plutonium

    International Nuclear Information System (INIS)

    Hooker, R.L.

    1981-11-01

    A full-scale (5 kg/h) incinerator is being tested with nonradioactive feed materials which simulate SRP-generator combustible transuranic wastes. The incinerator is two-stage and is designed to provide relatively quiescent conditions in the primary chamber where the ash is formed. This feature should minimize entrainment of Pu-bearing particles into the off-gas system. A series of runs have been completed in which incinerator feed was spiked with dysprosium to simulate Pu. Carryover of Dy into the off-gas system was found to be low (about 1/4%). 4 figures, 3 tables

  19. Incorporation of dysprosium ions into PbTiO3 ferroelectric ceramic system

    Directory of Open Access Journals (Sweden)

    A. Peláiz-Barranco

    2015-03-01

    Full Text Available A structural analysis concerning the incorporation of dysprosium into A- and/or B-sites of the lead titanate is shown. The two "boundary" refinements are presented, i.e., Dy2+ substitutes for Pb2+ (Dy3+ substitutes for Ti4+ and Dy3+ substitutes for Pb2+ (Dy3+ substitutes for Ti4+. The results offer quantitative information about the incorporation into both crystallographic sites. The increase of Dy3+ fraction into B-site provides the increase of the Ti4+ atomic displacement along the [001] direction and the tetragonal distortion.

  20. Dosimetric properties of dysprosium doped calcium magnesium borate glass subjected to Co-60 gamma ray

    Energy Technology Data Exchange (ETDEWEB)

    Omar, R. S., E-mail: ratnasuffhiyanni@gmail.com; Wagiran, H., E-mail: husin@utm.my; Saeed, M. A. [Department of Physics, Faculty of Science, Universiti Teknologi Malaysia, 81310 Johor Bahru (Malaysia)

    2016-01-22

    Thermoluminescence (TL) dosimetric properties of dysprosium doped calcium magnesium borate (CMB:Dy) glass are presented. This study is deemed to understand the application of calcium as the modifier in magnesium borate glass with the presence of dysprosium as the activator to be performed as TL dosimeter (TLD). The study provides fundamental knowledge of a glass system that may lead to perform new TL glass dosimetry application in future research. Calcium magnesium borate glass systems of (70-y) B{sub 2}O{sub 3} − 20 CaO – 10 MgO-(y) Dy{sub 2}O{sub 3} with 0.05  mol % ≤ y ≤ 0.7  mol % of dyprosium were prepared by melt-quenching technique. The amorphous structure and TL properties of the prepared samples were determined using powder X-ray diffraction (XRD) and TL reader; model Harshaw 4500 respectively. The samples were irradiated to Co-60 gamma source at a dose of 50 Gy. Dosimetric properties such as annealing procedure, time temperature profile (TTP) setting, optimization of Dy{sub 2}O{sub 3} concentration of 0.5 mol % were determined for thermoluminescence dosimeter (TLD) reader used.

  1. Treatment of rheumatoid synovitis of the knee with intraarticular injection of dysprosium 165-ferric hydroxide macroaggregates

    International Nuclear Information System (INIS)

    Sledge, C.B.; Zuckerman, J.D.; Zalutsky, M.R.

    1986-01-01

    One hundred eight knees of 93 patients with seropositive rheumatoid arthritis and persistent synovitis of the knee were treated with an intraarticular injection of 270 mCi of dysprosium 165 bound to ferric hydroxide macroaggregate. Leakage of radioactivity from the injected joint was minimal. Mean leakage to the venous blood 3 hours after injection was 0.11% of the injected dose; this corresponds to a mean whole body dose of 0.2 rads. Mean leakage to the liver 24 hours after injection was 0.64% of the injected dose; this corresponds to a mean liver dose of 3.2 rads. In 7 additional patients examined, there was negligible or near negligible activity found in the draining inguinal lymph nodes. One-year followup was possible for 74 knees (63 patients). Sixty-one percent of the knees had good results, 23% had fair results, and 16% had poor results. There was a direct correlation between the radiographic stage and response to treatment. In knees with stage I radiographic changes, 72% showed good results; 93% showed improvement. In knees with stage II changes, 59% showed good results; 81% showed improvement. These preliminary results indicate that dysprosium 165-ferric hydroxide macroaggregate is an effective agent for radiation synovectomy. The low leakage rates observed offer a definite advantage over agents previously used

  2. Dual responsive dysprosium-doped hydroxyapatite particles and toxicity reduction after functionalization with folic and glucuronic acids

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez Lafarga, Ana Karen; Pacheco Moisés, Fermín P. [Departamento de Química, Universidad de Guadalajara, Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico); Gurinov, Andrey [Research Resources Center for Magnetic Resonance, Saint Petersburg State University, Universitetskij pr. 26, 198504 St. Petersburg (Russian Federation); Ortiz, Genaro Gabriel [Laboratorio Desarrollo-Envejecimiento, Enfermedades Neurodegenerativas, Centro de Investigación Biomédica de Occidente (CIBO), Instituto Mexicano de Seguro Social (IMSS), Guadalajara, Jalisco (Mexico); Carbajal Arízaga, Gregorio Guadalupe, E-mail: gregoriocarbajal@yahoo.com.mx [Departamento de Química, Universidad de Guadalajara, Marcelino García Barragán 1421, C.P. 44430, Guadalajara, Jalisco (Mexico)

    2015-03-01

    The development of probes for biomedical applications demands materials with low toxicity levels besides fluorescence or magnetic properties to be detected by confocal microscopes or MRI resonators. Several drug delivery systems or other biomedical materials prepared with hydroxyapatite have been proposed, however, toxicity effects might arise when the size of particles is nanometric. In this study, hydroxyapatite functionalized with glucuronic or folic acids presented lower oxidative stress, measured from lipoperoxides and nitric oxide indicators in rats than pure hydroxyapatite. In separated experiments, hydroxyapatite was doped with dysprosium cations by coprecipitation producing a single crystal phase with fluorescent properties easily visualized by confocal microscopy when excited at 488 nm. These particles also presented the ability to modify the proton relaxation time in T1 maps collected by magnetic resonance imaging. These modified hydroxyapatite nanoparticles could be candidates to design bimodal probes with low toxicity. - Highlights: • Hydroxyapatite functionalized with glucuronic acid reduced oxidative stress in rats. • Functionalization with folic acid reduced oxidative stress in rats. • Dysprosium doping does not affect the crystalline structure of hydroxyapatite. • Dysprosium doped particles are visible in fluorescent microscope. • Dysprosium doped particles act as MRI contrast agents.

  3. Kinetic stability of the dysprosium(3) complex with tetraazaporphine in acetic acid-water and acetic acid-methanol mixtures

    International Nuclear Information System (INIS)

    Khelevina, O.G.; Vojnov, A.A.

    1999-01-01

    Water-soluble dysprosium tetraazaporphine with acetylacetonate-ion as extraligand is synthesized for the first time. Its kinetic stability in acetic acid solutions is investigated. It is shown that the complex is dissociated with formation of free tetraazaporphine. Kinetic parameters of dissociation reaction are determined [ru

  4. Dual responsive dysprosium-doped hydroxyapatite particles and toxicity reduction after functionalization with folic and glucuronic acids

    International Nuclear Information System (INIS)

    Sánchez Lafarga, Ana Karen; Pacheco Moisés, Fermín P.; Gurinov, Andrey; Ortiz, Genaro Gabriel; Carbajal Arízaga, Gregorio Guadalupe

    2015-01-01

    The development of probes for biomedical applications demands materials with low toxicity levels besides fluorescence or magnetic properties to be detected by confocal microscopes or MRI resonators. Several drug delivery systems or other biomedical materials prepared with hydroxyapatite have been proposed, however, toxicity effects might arise when the size of particles is nanometric. In this study, hydroxyapatite functionalized with glucuronic or folic acids presented lower oxidative stress, measured from lipoperoxides and nitric oxide indicators in rats than pure hydroxyapatite. In separated experiments, hydroxyapatite was doped with dysprosium cations by coprecipitation producing a single crystal phase with fluorescent properties easily visualized by confocal microscopy when excited at 488 nm. These particles also presented the ability to modify the proton relaxation time in T1 maps collected by magnetic resonance imaging. These modified hydroxyapatite nanoparticles could be candidates to design bimodal probes with low toxicity. - Highlights: • Hydroxyapatite functionalized with glucuronic acid reduced oxidative stress in rats. • Functionalization with folic acid reduced oxidative stress in rats. • Dysprosium doping does not affect the crystalline structure of hydroxyapatite. • Dysprosium doped particles are visible in fluorescent microscope. • Dysprosium doped particles act as MRI contrast agents

  5. 7 CFR 930.162 - Exemptions.

    Science.gov (United States)

    2010-01-01

    ... MICHIGAN, NEW YORK, PENNSYLVANIA, OREGON, UTAH, WASHINGTON, AND WISCONSIN Administrative Rules and Regulations § 930.162 Exemptions. (a) General. Tart cherries which are used for the purpose of new product... and/or new markets for tart cherry products. Any exemption for experimental work shall be limited in...

  6. 46 CFR 162.039-3 - Requirements.

    Science.gov (United States)

    2010-10-01

    ...: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Extinguishers, Fire, Semiportable, Marine Type § 162.039-3... parts, except those used for inversion mechanism or similar purposes, shall be corrosion-resistant to... shall be protected by a suitable corrosion-resistant coating. (1) Corrosion-resistant materials. The...

  7. 32 CFR 162.6 - Procedures.

    Science.gov (United States)

    2010-07-01

    ... Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DEFENSE CONTRACTING PRODUCTIVITY ENHANCING CAPITAL INVESTMENT (PECI) § 162.6 Procedures. The following procedures shall be followed by the DoD Components in the... documentation, pre-investment analysis, financing, and post-investment accountability of PECI projects, when DoD...

  8. 32 CFR 162.3 - Definition.

    Science.gov (United States)

    2010-07-01

    ... Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DEFENSE CONTRACTING PRODUCTIVITY ENHANCING CAPITAL INVESTMENT (PECI) § 162.3 Definition. (a) Capital Investment. The acquisition, installation, transportation... timeliness. (l) Productivity Enhancing Capital Investment (PECI). Equipment or facility funding that shall...

  9. Watt-level dysprosium fiber laser at 315 μm with 73% slope efficiency

    Science.gov (United States)

    Woodward, R. I.; Majewski, M. R.; Bharathan, G.; Hudson, D. D.; Fuerbach, A.; Jackson, S. D.

    2018-04-01

    Rare-earth-doped fiber lasers are emerging as promising high-power mid-infrared sources for the 2.6-3.0 {\\mu}m and 3.3-3.8 {\\mu}m regions based on erbium and holmium ions. The intermediate wavelength range, however, remains vastly underserved, despite prospects for important manufacturing and defense applications. Here, we demonstrate the potential of dysprosium-doped fiber to solve this problem, with a simple in-band pumped grating-stabilized linear cavity generating up to 1.06 W at 3.15 {\\mu}m. A slope efficiency of 73% with respect to launched power (77% relative to absorbed power) is achieved: the highest value for any mid-infrared fiber laser to date, to the best of our knowledge. Opportunities for further power and efficiency scaling are also discussed.

  10. Investigation on rare earth magnets recycling by organophosphoric extractant encapsulated polymeric beads for separation of dysprosium

    International Nuclear Information System (INIS)

    Yadav, Kartikey K.; Singh, D.K.; Kain, V.

    2017-01-01

    Rare earth elements (REEs) are a basic requirement of the electronics and new industries including green technology. In the present work an organophosphoric extractant encapsulating polyethersulfone (PES) beads has been developed and employed for dysprosium (Dy) separation from aqueous stream. Polyethersulfonic beads encapsulating PC88A were prepared by phase inversion method. During the synthesis of the beads, preparatory parameters were also optimized to obtain best suited beads which were subsequently characterized for their encapsulation capacity and micro structural investigation. The results obtained in the present investigation suggested that PES/PVAJPC88A composite beads could be used for separation of rare earths from aqueous medium obtained from the solubilisation of magnetic scrap materials

  11. Design and validation of a photon insensitive multidetector neutron spectrometer based on Dysprosium activation foils

    International Nuclear Information System (INIS)

    Gómez-Ros, J.M.; Bedogni, R.; Palermo, I.; Esposito, A.; Delgado, A.; Angelone, M.; Pillon, M.

    2011-01-01

    This communication describes a photon insensitive passive neutron spectrometer consisting of Dysprosium (Dy) activation foils located along three perpendicular axes within a single moderating polyethylene sphere. The Monte Carlo code MCNPX 2.6 was used to optimize the spatial arrangement of the detectors and to derive the spectrometer response matrix. Nearly isotropic response in terms of neutron fluence for energies up to 20 MeV was obtained by combining the readings of the detectors located at the same radius value. The spectrometer was calibrated using a previously characterized 14 MeV neutron beam produced in the ENEA Frascati Neutron Generator (FNG). The overall uncertainty of the spectrometer response matrix at 14 MeV, assessed on the basis of this experiment, was ±3%.

  12. Influence of modifiers on the separation of dysprosium from neodymium using organophosphorus acid derivates

    Energy Technology Data Exchange (ETDEWEB)

    Elwert, Tobias; Schwarz, Sabrina; Goldmann, Daniel [TU Clausthal, Clausthal-Zellerfeld (Germany). Lehrstuhl fuer Rohstoffaufbereitung und Recycling

    2016-01-15

    The aim of this study was to investigate the applicability of three organophosphorus acid derivates (D2EHPA, EHEHPA and Cyanex 572) for the separation of terbium and dysprosium from praseodymium and neodymium from NdFeB magnets in chloride solution. A special focus was put on the effect of phase modifiers. The investigations revealed that all extractants show in general a similar extraction behavior but the extraction is shifted to higher pH values in the order D2EHPA < EHEHPA < Cyanex 572. Therefore, and due to higher realizable loadings, EHEHPA and Cyanex 572 are more suitable for the investigated separation problem than D2EHPA. Whereas EHEHPA requires 1-decanol as phase modifier, Cyanex 572 can be employed without modifier addition.

  13. Automated spectrofluorimetric determinations of terbium and dysprosium in rare earth mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Lyle, S.J.; Za' tar, N. (Kent Univ., Canterbury (UK))

    1983-12-01

    Several methods involving the use of water-soluble binary and ternary complexes have been proposed for the spectrofluorimetric determination based on terbium(III) emission at 545 nm. These are terbium(III) with (A) ethylenediamine-N,N'-bis(o-hydroxyphenylacetic acid), (B) o-hydroxyphenyliminodiacetic acid, (C) EDTA + 5-sulphosalicylic acid, (D) EDTA + 1,2-dihydroxybenzene-3,5-disulphonic acid disodium salt (Tiron), and (E) iminodiacetic acid (IDA) + Tiron. Two of the reagent mixtures (D and E) can also be used for the fluorimetric determination of dysprosium(III) at 582 nm. A comparison has been made of these methods in order to select the most satisfactory procedure with respect to selectivity, sensitivity and suitability for adaption to automatic operation. Results are given and discussed.

  14. Spectrographic determination of dysprosium in doped crystals of calcium sulfate used for dosimetric material

    International Nuclear Information System (INIS)

    Grigoletto, T.; Lordello, A.R.

    1984-01-01

    A spectrographic method is described for the quantitative determination of dysprosium in doped crystals of calcium sulphate. The consequences of the changes in some parameters of the excitation conditions, such as arc current, electrode type and total or partial burning of sample, in the analytical results are discussed. Matrix effects are investigated. Variations in the intensity of the spectral lines are verified by recording the spectrum in distinct photographic plates. The role of internal standard in analytical reproducibility and in counterbalance of the variations in the arc current and in the weight of sample is studied. Accuracy is estimated by comparative analysis of two calcium sulphate samples by X-Ray Fluorescence, Neutron Activation and Inductive Coupled Plasma Emission Spectroscopy. (M.A.C.) [pt

  15. Use of dispersive liquid-liquid microextraction for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium

    International Nuclear Information System (INIS)

    Mallah, M.H.; Atomic Energy Organization of Iran, Tehran; Shemirani, F.; Ghannadi Maragheh, M.

    2008-01-01

    A new preconcentration method of dispersive liquid-liquid microextraction (DLLME) was developed for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium. DLLME technique was successfully used as a sample preparation method. In this preconcentration method, an appropriate mixture of extraction solvent, disperser solvent was injected rapidly into an aqueous solution containing Sm, Eu, Gd and Dy after complex formation using chelating reagent of the 1-(2-pyridylazo)-2-naphthol (PAN). After phase separation, 0.5 mL of the settled phase containing enriched analytes was determined by inductively coupled plasma optical emission spectrometry (ICP-OES). The main factors affected the preconcentration of Sm, Eu, Gd and Dy were extraction and dispersive solvent type and their volume, extraction time, volume of chelating agent (PAN), centrifuge speed and drying temperature of the samples. Under the best operating condition simultaneous preconcentration factors of 80, 100, 103 and 78 were obtained for Sm, Eu, Gd and Dy, respectively. (author)

  16. A model for additive transport in metal halide lamps containing mercury and dysprosium tri-iodide

    International Nuclear Information System (INIS)

    Beks, M L; Haverlag, M; Mullen, J J A M van der

    2008-01-01

    The distribution of additives in a metal halide lamp is examined through numerical modelling. A model for a lamp containing sodium iodide additives has been modified to study a discharge containing dysprosium tri-iodide salts. To study the complex chemistry the method of Gibbs minimization is used to decide which species have to be taken into account and to fill lookup tables with the chemical composition at different combinations of elemental abundance, lamp pressure and temperature. The results from the model with dysprosium additives were compared with earlier results from the lamp containing sodium additives and a simulation of a pure mercury lamp. It was found that radial segregation creates the conditions required for axial segregation. Radial segregation occurs due to the unequal diffusion of atoms and molecules. Under the right conditions convection currents in the lamp can cause axial demixing. These conditions depend on the ratio of axial convection and radial diffusion as expressed by the Peclet number. At a Peclet number of unity axial segregation is most pronounced. At low Peclet numbers radial segregation is at its worst, while axial segregation is not present. At large Peclet numbers the discharge becomes homogeneously mixed. The degree of axial segregation at a Peclet number of unity depends on the temperature at which the additive under consideration fully dissociates. If the molecules dissociate very close to the walls no molecules are transported by the convective currents in the lamp, and hence axial segregation is limited. If they dissociate further away from the walls in the area where the downward convective currents are strongest, more axial segregation is observed

  17. Electrochemical behaviour of dysprosium in the eutectic LiCl-KCl at W and Al electrodes

    International Nuclear Information System (INIS)

    Castrillejo, Y.; Bermejo, M.R.; Barrado, A.I.; Pardo, R.; Barrado, E.; Martinez, A.M.

    2005-01-01

    The electrochemical behaviour of DyCl 3 was studied in the eutectic LiCl-KCl at different temperatures. The cathodic reaction can be written:Dy(III)+3e-bar Dy(0)which can be divided in two very close cathodic steps:Dy(III)+1e-bar Dy(II)andDy(II)+2e-bar Dy(0)Transient electrochemical techniques, such as cyclic voltammetry, chronopotentiometry, and chronoamperometry were used in order to study the reaction mechanism and the transport parameters of electroactive species at a tungsten electrode. The results showed that in the eutectic LiCl-KCl, electrocrystallization of dysprosium seems to be the controlling electrochemical step. Chronoamperometric studies indicated instantaneous nucleation of dysprosium with three dimensional growth of the nuclei whatever the applied overpotential.Mass transport towards the electrode is a simple diffusion process, and the diffusion coefficient of the electroactive species, i.e. Dy(III), has been calculated. The validity of the Arrhenius law was also verified by plotting the variation of the logarithm of the diffusion coefficient versus 1/T.In addition, the electrode reactions of the LiCl-KCl-DyCl 3 solutions at an Al wire were also investigated by cyclic voltammetry and open circuit chronopotentiometry. The redox potential of the Dy(III)/Dy couple at the Al electrode was observed at more positive potentials values than those at the inert electrode. This potential shift was thermodynamically analyzed by a lowering of activity of Dy in the metal phase due to the formation of intermetallic compounds

  18. Dysprosium lithium borate glass mircrospheres for radiation synovectomy: The in vitro and in vivo performance evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Di; Yu Jing [Institute of Bioengineering and Information Technology Materials, Center for Advanced Materials and Nano-Biomedicine, Tongji University, Shanghai, 200092 (China); Huang Wenhai, E-mail: whhuang@tongji.edu.cn [Institute of Bioengineering and Information Technology Materials, Center for Advanced Materials and Nano-Biomedicine, Tongji University, Shanghai, 200092 (China); Zhou Nai; Wang Deping [Institute of Bioengineering and Information Technology Materials, Center for Advanced Materials and Nano-Biomedicine, Tongji University, Shanghai, 200092 (China); Yin Wei [Institute of Isotope Research, Sinitic Academy of Atomic Energy, Beijing 102413 (China); Chen Yaqing [The Sixth People' s Hospital, Shanghai 200233 (China)

    2010-08-30

    The radioactive dysprosium lithium borate glass (DyLB) microspheres with different glass compositions were prepared for radiation synovectomy. The biodegradability and biocompatibility of these DyLB microspheres were evaluated in vitro and in vivo. The DyLB microspheres studied in this work were partially biodegradable in a simulated body fluid (SBF), with the final weight loss of the microspheres in the range of 24.6% and 55.0% (wt.%) after 8 days of immersion. The ICP results revealed that the dissolution of lithium significantly decreased from 100% to 53.7% with increasing content of Dy{sub 2}O{sub 3} in the microspheres from 18% to 22% (wt.%, from S-1 to S-3). However, for all of the three samples, nearly all of the dysprosium (> 99.997%, wt.%) remained in the microspheres, in the form of insoluble phosphates and carbonates, which was proved by the SEM and EDX analyses. The degradation of DyLB microspheres in SBF gradually decreased with immersion time and eventually reached equilibrium after 7 days of immersion. Compared to the other two samples, the S-3 sample with the lowest Dy{sup 3+} dissolution (about 0.002%) was considered more secure for clinical application. Furthermore, the S-3 DyLB microspheres exhibited good biocompatibility, since neither tissue damage nor inflammation was observed, after they were implanted in the liver of rat for two weeks. After neutron activation, the radionuclide purity of radioactive S-3 DyLB microspheres was 99.999%, which were suitable for radiation synovectomy.

  19. Photoluminescence study on amino functionalized dysprosium oxide-zinc oxide composite bifunctional nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Joseph, Aswathy; Praveen, G.L; Abha, K.; Lekha, G.M [Department of Chemistry, University of Kerala, Kariavattom, Kerala 695581 (India); George, Sony, E-mail: emailtosony@gmail.com [Department of Chemistry, University of Kerala, Kariavattom, Kerala 695581 (India)

    2012-08-15

    An organic dispersion of 9-15 nm size stable dysprosium oxide incorporated zinc oxide nanocomposites exhibiting luminescence in the visible region has been synthesised by a wet chemical precipitation technique at room temperature. Tetraethoxysilane TEOS [(C{sub 2}H{sub 5}O){sub 4}Si], (3-aminopropyl) trimethoxysilane (APTS) and a 1:1 mixture of TEOS-APTS have been used as capping agents to control the particle size as well as to achieve uniform dispersion of composite nanoparticles in methanol medium. X-ray diffractometer (XRD) analysis reveals the formation phase of amino-functionalised colloidal dysprosium oxide incorporated ZnO composite nanoparticles to be of zincite structure. The Transmission Electron Microscopy (TEM) images show that the particles are spheroids in shape, having average crystalline sizes ranging from 9 to 15 nm. The photoluminescence (PL) observed in these composites has been attributed to the presence of near band edge excitonic emission and existence of defect centres. The time correlated single photon counting studies of the composite nanoparticles exhibited three decay pathways. The enhanced PL emission intensity of solid state fluorescence spectra of samples is attributed to the absence of vibrational relaxation process. - Highlights: Black-Right-Pointing-Pointer Nano-composites are synthesised using a one step wet chemical precipitation method. Black-Right-Pointing-Pointer A significant fluorescence life time of 8.25 ns is obtained for the nano-composite. Black-Right-Pointing-Pointer Nano-composite particles exhibited pale yellow fluorescence rather than blue. Black-Right-Pointing-Pointer Vibrational cascade free enhanced fluorescence is obtained for the dry sample.

  20. 32 CFR Appendix to Part 162 - Reporting Procedures

    Science.gov (United States)

    2010-07-01

    ... ENHANCING CAPITAL INVESTMENT (PECI) Pt. 162, App. A Appendix to Part 162—Reporting Procedures A. General The.... Total Projected Life-Cycle Cost Avoidance. 4. PIA Post-Investment assessments, articles, pictures, and...

  1. 26 CFR 1.162-6 - Professional expenses.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Professional expenses. 1.162-6 Section 1.162-6...) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations § 1.162-6 Professional expenses. A professional man may claim as deductions the cost of supplies used by him in the practice of...

  2. 45 CFR 162.915 - Trading partner agreements.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Trading partner agreements. 162.915 Section 162... REQUIREMENTS ADMINISTRATIVE REQUIREMENTS General Provisions for Transactions § 162.915 Trading partner agreements. A covered entity must not enter into a trading partner agreement that would do any of the...

  3. 19 CFR 162.63 - Arrests and seizures.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Arrests and seizures. 162.63 Section 162.63 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY (CONTINUED) INSPECTION, SEARCH, AND SEIZURE Controlled Substances, Narcotics, and Marihuana § 162...

  4. 45 CFR 162.1002 - Medical data code sets.

    Science.gov (United States)

    2010-10-01

    ... Terminology, Fourth Edition (CPT-4), as maintained and distributed by the American Medical Association, for... 45 Public Welfare 1 2010-10-01 2010-10-01 false Medical data code sets. 162.1002 Section 162.1002... REQUIREMENTS ADMINISTRATIVE REQUIREMENTS Code Sets § 162.1002 Medical data code sets. The Secretary adopts the...

  5. 46 CFR 162.050-37 - Vibration test.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Vibration test. 162.050-37 Section 162.050-37 Shipping...: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Pollution Prevention Equipment § 162.050-37 Vibration test. (a... paragraph (b) of this section. The test must be performed at an independent laboratory that has the...

  6. 45 CFR 162.1011 - Valid code sets.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Valid code sets. 162.1011 Section 162.1011 Public... ADMINISTRATIVE REQUIREMENTS Code Sets § 162.1011 Valid code sets. Each code set is valid within the dates specified by the organization responsible for maintaining that code set. ...

  7. 26 CFR 1.162-1 - Business expenses.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Business expenses. 1.162-1 Section 1.162-1...) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations § 1.162-1 Business expenses. (a) In general. Business expenses deductible from gross income include the ordinary and necessary...

  8. 16 CFR 1.62 - Ancillary court orders pending review.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Ancillary court orders pending review. 1.62 Section 1.62 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL PROCEDURES Injunctive and Condemnation Proceedings § 1.62 Ancillary court orders pending review...

  9. 19 CFR 162.11 - Authority to procure warrants.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Authority to procure warrants. 162.11 Section 162.11 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY (CONTINUED) INSPECTION, SEARCH, AND SEIZURE Search Warrants § 162.11 Authority to procure...

  10. 19 CFR 162.92 - Notice of seizure.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Notice of seizure. 162.92 Section 162.92 Customs... (CONTINUED) INSPECTION, SEARCH, AND SEIZURE Civil Asset Forfeiture Reform Act § 162.92 Notice of seizure. (a) Generally. Customs will send written notice of seizure as provided in this section to all known interested...

  11. 19 CFR 162.22 - Seizure of conveyances.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Seizure of conveyances. 162.22 Section 162.22... TREASURY (CONTINUED) INSPECTION, SEARCH, AND SEIZURE Seizures § 162.22 Seizure of conveyances. (a) General applicability. If it shall appear to any officer authorized to board conveyances and make seizures that there...

  12. Simultaneous determination of dysprosium, holmium and erbium in high purity rare earth oxides by second order derivative spectrophotometry

    International Nuclear Information System (INIS)

    Anbu, M.; Prasada Rao, T.; Iyer, C. S. P.; Damodaran, A. D.

    1996-01-01

    High purity individual rare earth oxides are increasingly used as major components in lasers (Y 2 O 3 ), phosphors (YVO 3 , Eu 2 O 3 ), magnetic bubble memory films (Gd 2 O 3 ) and refractive-index lenses and fibre optics (La 2 O 3 ). The determination of individual lanthanides in high purity rare earth oxides is a more important and difficult task. This paper reports the utilization of higher order derivative spectrophotometry for the simultaneous determination of dysprosium, holmium and erbium in high purity rare earth oxides. The developed procedure is simple, reliable and allows the determination of 0.001 to 0.2% of dysprosium, holmium and erbium in several rare earth. (author). 9 refs, 2 figs, 2 tabs

  13. Mixed (phthalocyaninato)(Schiff-base) di-dysprosium sandwich complexes. Effect of magnetic coupling on the SMM behavior.

    Science.gov (United States)

    Wang, Hailong; Liu, Chenxi; Liu, Tao; Zeng, Suyuan; Cao, Wei; Ma, Qi; Duan, Chunying; Dou, Jianmin; Jiang, Jianzhuang

    2013-11-21

    Reaction between Schiff-base ligand and half-sandwich complex M(Pc)(acac) led to the isolation of new sandwich-type mixed (phthalocyaninato)(Schiff-base) di-lanthanide compounds M2(Pc)2(L)H2O (M = Dy, Gd) (1, 2) [H2Pc = metal free phthalocyanine, Hacac = acetylacetone, H2L = N,N'-bis(3-methyloxysalicylidene)benzene-1,2-diamine] with the triple-decker molecular structure clearly revealed by single crystal X-ray diffraction analysis. For the comparative studies, sandwich triple-decker analogues with pure Schiff-base ligand M2(L)3H2O (M = Dy, Gd) (3, 4) were also prepared. Dynamic magnetic measurement result reveals the single-molecule magnet (SMM) nature of the di-dysprosium derivative 1, while the static magnetic investigation over both pure and the diamagnetic diluted samples of this compound discloses the interionic ferromagnetic coupling between the two dysprosium ions, which in turn effectively suppresses the QTM and enhances the energy barrier of this SMM. Nevertheless, comparative studies over the static magnetic properties of the di-dysprosium triple-decker complexes 1 and 3 indicate the stronger magnetic coupling between the two lanthanide ions in mixed (phthalocyaninato)(Schiff-base) species than in the pure Schiff-base triple-decker analogue, suggesting the special coordination sphere around the dysprosium ions in the former compound over the latter one on the more intense inter-ionic ferromagnetic coupling. As a very small step towards understanding the structure-property relationship, the present result will be surely helpful for the design and synthesis of the multinuclear lanthanide-based SMMs with good properties.

  14. Study of 162Er via the (p , t) and (p ,p') reactions

    Science.gov (United States)

    Kisliuk, D.; Garrett, P. E.; Finlay, A.; Bianco, L.; Bildstein, V.; Burbadge, C.; Chagnon-Lessard, S.; Diaz Varela, A.; Dunlop, M. R.; Dunlop, R.; Finlay, P.; Jamieson, D.; Jigmeddorj, B.; Maclean, A. D.; Michetti-Wilson, J.; Leach, K. G.; Radich, A. J.; Rand, E.; Svensson, C. E.; Wong, J.; Ball, G. C.; Triambak, S.; Faestermann, T.; Hertenberger, R.; Wirth, H.-F.

    2015-10-01

    The nature of excited states in well-deformed nuclei pose a challenge in nuclear structure. In light of this, the study of 162Er via the 164Er (p , t) and 162Er (p ,p') reactions has been initiated to shed light on the structure of these excited states. The experiments were performed at the Maier-Leibnitz Laboratory using a 22 MeV proton beam on highly-enriched targets of 162,164Er and the reaction was analyzed with the Q3D spectrograph. Strong population in the (p , t) reaction of the 02+ state, far greater than other 0+ states, has been observed. Transition matrix elements for population of low-lying states in the (p ,p') reaction have also been extracted. Initial results from these experiments will be presented.

  15. Evaluating United States and world consumption of neodymium, dysprosium, terbium, and praseodymium in final products

    Science.gov (United States)

    Hart, Matthew

    This paper develops scenarios of future rare-earth-magnet metal (neodymium, dysprosium, terbium, and praseodymium) consumption in the permanent magnets used in wind turbines and hybrid electric vehicles. The scenarios start with naive base-case scenarios for growth in wind-turbine and hybrid-electric-vehicle sales over the period 2011 to 2020, using historical data for each good. These naive scenarios assume that future growth follows time trends in historical data and does not depend on any exogenous variable. Specifically, growth of each technological market follows historical time trends, and the amount of rare earths used per unit of technology remains fixed. The chosen reference year is 2010. Implied consumptions of the rare earth magnet metals are calculated from these scenarios. Assumptions are made for the material composition of permanent magnets, the market share of permanent-magnet wind turbines and vehicles, and magnet weight per unit of technology. Different scenarios estimate how changes in factors like the material composition of magnets, growth of the economy, and the price of a substitute could affect future consumption. Each scenario presents a different method for reducing rare earth consumption and could be interpreted as potential policy choices. In 2010, the consumption (metric tons, rare-earth-oxide equivalent) of each rare-earth-magnet metal was as follows. Total neodymium consumption in the world for both technologies was 995 tons; dysprosium consumption was 133 tons; terbium consumption was 50 tons; praseodymium consumption was zero tons. The base scenario for wind turbines shows there could be strong, exponential growth in the global wind turbine market. New U.S. sales of hybrid vehicles would decline (in line with the current economic recession) while non-U.S. sales increase through 2020. There would be an overall increase in the total amount of magnetic rare earths consumed in the world. Total consumption of each rare earth in the short

  16. Spectrographic determination of dysprosium dopant in calcium sulphate used as dosimetric material

    International Nuclear Information System (INIS)

    Grigoletto, T.

    1982-01-01

    A spectrographic method is described for the quantitative determination of dysprosium in doped crystals of calcium sulphate. The consequences of the changes in some parameters of the excitation conditions, such as arc current, electrode type and total or partial burning of sample, in the analytical results are discussed. Matrix effects are investigated by comparison among analytical curves obtained from three different methods of standard preparations. Variations in the intensity of the spectral lines are verificated by recording the spectrum in distinct photographic plates (SA-1). The role of internal standard in analytical reproducibility and in counterbalance of the variations in the arc current and in the weight of sample are studied. The great similarity in excitation behavior of many of the rare earths is used to provide a high degree of internal standardization. Precision studies show a standard deviation of about + - 2,4 percent by use of lanthanum as an internal standard. Accuracy is estimate by comparative analysis of two calcium sulphate samples by X-Rays Fluorescence, Neutron Activation and Inductive Coupled Plasma (ICP) Emission Spectroscopy. (Author) [pt

  17. Combustion of gadolinium and dysprosium chelates as a cellular integrity marker in MR imaging

    International Nuclear Information System (INIS)

    Ericsson, A.; Bach-Gansmo, T.; Niklasson, F.; Hemmingsson, A.

    1995-01-01

    A combination of gadolinium (Gd) and dysprosium (Dy) chelates was investigated as a potential marker of cell-membrane integrity by means of a double-contrast effect in MR imaging. Blood samples with varying hematocrit (Hct) levels containing intact or lysed cells were used as model systems. With intact cells, the agents were assumed to be distributed solely extracellularly and the highest Hct studied (69%) was assumed to mimic the ratio of extracellular to intracellular water in tissue. The combined effect on image intensity of Gd (in a concentration corresponding to 0.2 mmol/kg b.w. in humans) and Dy (0.6 mmol/kg b.w.) applied simultaneously was a marked difference in signal intensity between samples with intact and lysed cells in both the T1- and T2-weighted spin-echo images with a corresponding increase in the contrast-to-noise ratio. This was the result of a T1 reduction caused by Gd with a negligible Dy susceptibility effect in areas with lysed cells. On the other hand, the Dy susceptibility effect (i.e. reduced apparent T2) dominated in areas with intact cells. Thus, the combination of Gd and Dy may serve as a marker of cell-membrane integrity in MR examinations. (orig.)

  18. Self-organized dysprosium-directed alginate hydrogels and its chemical features

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Qianmin [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Gao, Jinwei [Institute for Advanced Materials, Academy of Advanced Optoelectronics, South China Normal University, Guangzhou 510006 (China); Peng, Huojun [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Wang, Qianming, E-mail: qmwang@scnu.edu.cn [Key Laboratory of Theoretical Chemistry of Environment, Ministry of Education, School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Guangzhou Key Laboratory of Materials for Energy Conversion and Storage, Guangzhou 510006 (China)

    2016-09-15

    Rational use of self-organized materials may contribute in developing new structures and devices in practical technology. Synthetic metallo-supramolecular gels are generally designed with transitional metal-directed process. However, the assembly of both lanthanide and sodium alginate in macromolecular systems would find a new way of utilizing its physical properties. The stimuli-responsive molecule (alginate) could firmly form stable hydrogels upon the encapsulation of dysprosium ions. In addition, the immobilization of YVO{sub 4}: Eu{sup 3+} nanoparticle in the soft matrix has been achieved and it has never been explored in the fabrication of phosphor-incorporated luminescent alginate gels. The key feature of the present soft matter is that its red emission could be switched off in the presence of sodium ascorbate and the results may have a tremendous impact on the extension of photophysical application based on soft nanoscale devices. - Highlights: • Dy{sup 3+} can be used for the gelation of the dissolved alginate. • Lanthanide hydrogels could exhibit red emissions under excitations. • Luminescence could be switched “off” in the presence of sodium ascorbate.

  19. Optical properties of zinc borotellurite glass doped with trivalent dysprosium ion

    Science.gov (United States)

    Ami Hazlin, M. N.; Halimah, M. K.; Muhammad, F. D.; Faznny, M. F.

    2017-04-01

    The zinc borotellurite doped with dysprosium oxide glass samples with chemical formula {[(TeO2) 0 . 7(B2O3) 0 . 3 ] 0 . 7(ZnO) 0 . 3 } 1 - x(Dy2O3)x (where x=0.01, 0.02, 0.03, 0.04 and 0.05 M fraction) were prepared by using conventional melt quenching technique. The structural and optical properties of the proposed glass systems were characterized by using X-ray diffraction (XRD) spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, and UV-VIS spectroscopy. The amorphous nature of the glass systems is confirmed by using XRD technique. The infrared spectra of the glass systems indicate three obvious absorption bands which are assigned to BO3 and TeO4 vibrational groups. Based on the absorption spectra obtained, the direct and indirect optical band gaps, as well as the Urbach energy were calculated. It is observed that both the direct and indirect optical band gaps increase with the concentration of Dy3+ ions. On the other hand, the Urbach energy is observed to decrease as the concentration of Dy3+ ions increases.

  20. The liquid membrane for extraction of Yttrium and Dysprosium from Acid Nitric

    International Nuclear Information System (INIS)

    Johny, W.S.; Raldi-Artono-Koestoer; Kris-Tri-Basuki; Sudibyo

    1996-01-01

    The determination of surfactant in liquid membrane has been done. The surfactant is span-80 (sorbitol-monooleate), the liquid membrane phase was the organic phase (O), the internal liquid phase (W) with ratio O/W = 1, and surfactant. The organic phase using D 2 EHPA in the kerosene and the internal liquid phase using aqua des or acid nitric. The determination of surfactant with variation of span-80 (0,25 - 2%) in the liquid membrane volume. The speed of stirrer was 3500 rpm in 20 minute. The ratio of liquid membrane phase form and external phase (aqua des or acid nitric) was 1, the speed of stirrer was 350 rpm in 10 minute (permeation process). The liquid phase and the liquid membrane phase was separated and then determinated the volume of liquid membrane, the result of percentage of span-80 was 0,25 % volume. The extraction of yttrium and dysprosium in 2 M HNO 3 was Kd y = 2.945 and Kd D y = 0.019

  1. 25 CFR 162.605 - Negotiation of leases.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Negotiation of leases. 162.605 Section 162.605 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER LEASES AND PERMITS Non-Agricultural Leases § 162.605 Negotiation of leases. (a) Leases of individually owned land or tribal land may be negotiated by those owners or their...

  2. Custom Coordination Environments for Lanthanoids: Tripodal Ligands Achieve Near-Perfect Octahedral Coordination for Two Dysprosium-Based Molecular Nanomagnets.

    Science.gov (United States)

    Lim, Kwang Soo; Baldoví, José J; Jiang, ShangDa; Koo, Bong Ho; Kang, Dong Won; Lee, Woo Ram; Koh, Eui Kwan; Gaita-Ariño, Alejandro; Coronado, Eugenio; Slota, Michael; Bogani, Lapo; Hong, Chang Seop

    2017-05-01

    Controlling the coordination sphere of lanthanoid complexes is a challenging critical step toward controlling their relaxation properties. Here we present the synthesis of hexacoordinated dysprosium single-molecule magnets, where tripodal ligands achieve a near-perfect octahedral coordination. We perform a complete experimental and theoretical investigation of their magnetic properties, including a full single-crystal magnetic anisotropy analysis. The combination of electrostatic and crystal-field computational tools (SIMPRE and CONDON codes) allows us to explain the static behavior of these systems in detail.

  3. Experimental and theoretical approach on the optical properties of zinc borotellurite glass doped with dysprosium oxide

    Science.gov (United States)

    Halimah, M. K.; Ami Hazlin, M. N.; Muhammad, F. D.

    2018-04-01

    A series of glass samples with chemical formula {[(TeO2)0.7(B2O3)0.3]0.7(ZnO)0.3}1 - x(Dy2O3)x where x = 0.01, 0.02, 0.03, 0.04 and 0.05 M fraction were synthesized through conventional melt-quenching method. The most common way to fabricate a glass material is by fusion of two or more component oxides followed by their quenching. This technique is known as melt-quenching technique. Kaur et al. (2016) [1] highlighted that the melt-quenching method able to enhance the mechanical properties like hardness and flexural strength of the material. The nature of the glass systems is proven to be amorphous based on the XRD pattern. The FTIR spectra of the glass systems confirm the existence of five bands which are assigned for the BO4, BO3, TeO4 and TeO3 vibrational groups. The density of the glass systems is increased with the addition of Dy2O3 while the molar volume is found to be inversely proportional to the density of the proposed glass. The optical properties of the glasses are determined through the absorption spectra obtained from the UV-VIS spectrophotometer. From the absorption spectra, the indirect and direct optical band gaps and the Urbach energy are found to be inversely proportional to each other. As the molar fraction of the Dy2O3 increased, the optical band gaps are observed to increase as opposed to the Urbach energy. For this glass system, the values of refractive index, electronic polarizability, oxide ion polarizability and the optical basicity are found to decrease as the addition of the dysprosium oxide is increased. From the emission spectra, two intense blue and yellow emission bands are observed, which correspond to the 4F9/2 → 6H15/2 and 4F9/2 → 6H13/2 transitions of Dy3 + ions respectively. The CIE chromaticity coordinates of the zinc borotellurite glass systems are found to be located in the white light region. Generation of white light The generation of the white light can be achieved by using two emission bands which comprise of the yellow

  4. Textured dysprosium and gadolinium poles for high-field, short-period hybrid undulators

    International Nuclear Information System (INIS)

    Murokh, Alex; Solovyov, Vyacheslav; Agustsson, Ron; O'Shea, Finn H.; Chubar, Oleg; Chen, Yung; Grandsaert, Thomas

    2014-01-01

    We discuss the feasibility of enhancement of the gap field in a short-period hybrid undulator by using pole inserts with the saturation inductance B s , over that of iron, 2 T. Dysprosium metal, with the saturation inductance of 3.4 T below 90 K, and Gadolinium with B s =2.7 T, appear as good candidates as the optimized pole material. However, due to the high magnetic anisotropy of Dy, such a high level of magnetization can only be realized when the external field lies in the basal plane. This implies that the pole has to be single-crystalline or highly textured. Considering that growing large, >10mm, Dy single crystals is difficult, we propose secondary recrystallization as a method to induce the required texture in thin Dy and Gd foils. The textured foils can be stacked to produce pole inserts of the desired geometry and orientation. Results of small-scale processing and magnetic measurements of thin (20–60 μ) foils provide evidence that the required texture quality can be achieved by a relatively simple sequence of heat-treatments and cold rolling. The advantage of textured Dy and Gd poles is demonstrated in a several period test undulator. -- Highlights: • Textured rare-earth materials for use as undulator pole materials. • We measure the development of texture in Dy and Gd. • We compare the rare-earth materials with high saturation steel in undulators. • Thin sheets of Dy and Gd materials perform similar to single crystals

  5. Brain abscess: surgical experiences of 162 cases

    Directory of Open Access Journals (Sweden)

    Forhad Hossain Chowdhury

    2015-01-01

    Full Text Available Aim: Brain abscess still poses a public health challenge in spite of the advent of modern neurosurgical techniques and antibiotics. Here, we present our surgical experiences and ultimate outcome in the management of brain abscess. Methods: Totally, 162 patients with proved brain abscess who underwent surgical treatment were included in this study. The prospectively recorded data of surgical management of brain abscess and the ultimate outcome (by Glasgow outcome scale were studied retrospectively. Results: Total number of cases was 162, of which 113 were acute pyogenic abscess while 49 were chronic abscess. Among the chronic abscess, 29 were chronic pyogenic abscess, 14 were tubercular, 3 aspergillus, and 3 abscesses were in malignant brain metastases. In acute cases, common clinical features were headache, fever, vomiting, focal deficit and seizure. In chronic abscesses, common clinical features were mild to moderate headache and progressive focal deficit. Seventy-three (45.06% patients had adjacent localized sinus, middle ear or cranial infection. The common predisposing factors included postneurosurgery, postpenetrating injury to brain, chronic suppurative otitis media, and congenital heart disease, infective endocarditis, sinusitis and sub optimum immuno-status. Frontal lobe involved in 30.2% cases, temporal lobe is next to involved. Single time burr hole aspiration in 111 (68.5% cases, two or more times burr hole aspiration were done in 34 (21% cases. Pus culture was negative in 129 (79.62% cases. Total number of death was 22 (13.58% cases. Complete resolution of abscess with complete recovery of preoperative neuro-deficit was seen in 80.86% cases and recovery with major neuro-deficit was observed in 5.55% cases. There is a significant association between Glasgow coma scale (GCS on admission and mortality in brain abscess. Conclusion: In most of the cases, pus culture did not yield growth of any causative organism. Mortality was not

  6. 19 CFR 162.3 - Boarding and search of vessels.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Boarding and search of vessels. 162.3 Section 162.3 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF... Boarding and search of vessels. (a) General authority. A Customs officer, for the purpose of examining the...

  7. 42 CFR 423.162 - Quality improvement organization activities.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Quality improvement organization activities. 423.162 Section 423.162 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICARE PROGRAM VOLUNTARY MEDICARE PRESCRIPTION DRUG BENEFIT Cost Control...

  8. 45 CFR 162.1901 - Medicaid pharmacy subrogation transaction.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Medicaid pharmacy subrogation transaction. 162... STANDARDS AND RELATED REQUIREMENTS ADMINISTRATIVE REQUIREMENTS Medicaid Pharmacy Subrogation § 162.1901 Medicaid pharmacy subrogation transaction. The Medicaid pharmacy subrogation transaction is the...

  9. 26 CFR 1.162-5 - Expenses for education.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Expenses for education. 1.162-5 Section 1.162-5... education. (a) General rule. Expenditures made by an individual for education (including research undertaken... the education may lead to a degree) if the education— (1) Maintains or improves skills required by the...

  10. 26 CFR 1.162-12 - Expenses of farmers.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Expenses of farmers. 1.162-12 Section 1.162-12... farmers. (a) Farms engaged in for profit. A farmer who operates a farm for profit is entitled to deduct... 263A and the regulations thereunder. For taxable years beginning after July 12, 1972, where a farmer is...

  11. 28 CFR 16.2 - Public reading rooms.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Public reading rooms. 16.2 Section 16.2 Judicial Administration DEPARTMENT OF JUSTICE PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION... Relations Service—in Suite 2000, 600 E Street, NW., Washington, DC; (4) Drug Enforcement Administration—in...

  12. 46 CFR 162.028-4 - Marine type label.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Marine type label. 162.028-4 Section 162.028-4 Shipping... type label. (a) In addition to all other marking, every portable extinguisher shall bear a label containing the “marine type” listing manifest issued by a recognized laboratory. This label will include the...

  13. 19 CFR 162.21 - Responsibility and authority for seizures.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Responsibility and authority for seizures. 162.21 Section 162.21 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY... authority for seizures. (a) Seizures by Customs officers. Property may be seized, if available, by any...

  14. 26 CFR 1.162-7 - Compensation for personal services.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Compensation for personal services. 1.162-7 Section 1.162-7 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME... a flat rate. Generally speaking, if contingent compensation is paid pursuant to a free bargain...

  15. 7 CFR 457.162 - Nursery crop insurance provisions.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Nursery crop insurance provisions. 457.162 Section 457... CORPORATION, DEPARTMENT OF AGRICULTURE COMMON CROP INSURANCE REGULATIONS § 457.162 Nursery crop insurance provisions. The Nursery Crop Insurance Provisions for the 2006 and succeeding crop years are as follows: FCIC...

  16. 46 CFR 162.017-3 - Materials, construction, and workmanship.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, and workmanship. 162.017-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Valves, Pressure-Vacuum Relief, for Tank Vessels § 162.017-3 Materials, construction, and workmanship. (a) The valves shall be of...

  17. Electrocatalytic approach for the efficiency increase of electrolytic hydrogen production: Proof-of-concept using platinum-dysprosium alloys

    International Nuclear Information System (INIS)

    Santos, D.M.F.; Šljukić, B.; Sequeira, C.A.C.; Macciò, D.; Saccone, A.; Figueiredo, J.L.

    2013-01-01

    Development of electrocatalytic materials for the hydrogen evolution reaction (HER) is attempted with the aim of reducing the water electrolysis overpotential and increasing its efficiency. Using linear scan voltammetry measurements of the hydrogen discharge enables evaluation of the electrocatalytic activity for the HER of platinum–dysprosium (Pt–Dy) intermetallic alloy electrodes of different compositions. Understanding of materials electrocatalytic performance is based on determination of several crucial kinetic parameters, including the Tafel coefficients, b, charge transfer coefficients, α, exchange current densities, j 0 , and activation energies, E a . Influence of temperature on HER is investigated by performing studies at temperatures ranging from 25 °C to 85 °C. The effect of the Dy amount in the efficiency of the HER on the Pt–Dy alloys is analysed. Results demonstrate that Dy can substantially increase the electrocatalytic activity of the Pt alloys, in comparison to the single Pt electrode. Efforts are made to correlate the microstructure of the alloys with their performance towards the HER. - Highlights: ► Development of electrocatalysts to increase efficiency of electrolytic hydrogen production. ► Synthesis and evaluation of composition and morphology of platinum–dysprosium (Pt–Dy) alloys. ► Hydrogen evolution reaction on Pt–Dy alloys electrodes studied using linear scan voltammetry in alkaline medium. ► Pt–Dy alloy with equiatomic composition enhances kinetics of hydrogen discharge compared to single Pt

  18. The application of x-ray spectrometry to isotopic-source activation analysis of dysprosium and holmium

    International Nuclear Information System (INIS)

    Pillay, A.E.; Mboweni, R.C.M.

    1990-01-01

    A novel aspect of activation analysis is described for the determination of dysprosium and holmium at low concentrations. The method involves the measurement of K x-rays from radionuclides produced by thermal neutron activation using a 1 mg 252 Cf source. The basis for elemental selection depends largely on the demand for analysis and on the existence of favourable nuclear properties for the production of a practicable x-ray yield. A full appraisal of the analytical potential of the method is presented with particular emphasis on its application to geological matrices. The sensitivity was optimised by employing a detector that was particularly effective at photon energies below 150 keV. Analytical conditions are demonstrated for the elements of interest over a wide range of concentrations in small powdered samples. The investigation formed the basis of a feasibility study to establish if the application could be developed for the routine off-line determination of dysprosium and holmium using an isotopic-neutron source. (author)

  19. Reduction of titanocene dichloride with dysprosium: access to a stable titanocene(ii) equivalent for phosphite-free Takeda carbonyl olefination.

    Science.gov (United States)

    Bousrez, G; Déchamps, I; Vasse, J-L; Jaroschik, F

    2015-05-28

    The reduction of titanocene dichloride with dysprosium yields a new titanocene(ii) equivalent without the need for further stabilising ligands. This reagent can be employed in combination with dithioacetals for the olefination of different carbonyl groups and allows for a simplified all-in-one procedure.

  20. High spin states in 162Lu

    International Nuclear Information System (INIS)

    Gupta, S.L.; Pancholi, S.C.; Juneja, P.; Mehta, D.; Kumar, A.; Bhowmik, R.K.; Muralithar, S.; Rodrigues, G.; Singh, R.P.

    1997-01-01

    An experimental investigation of the odd-odd 162 Lu nucleus, following the 148 Sm( 19 F,5n) reaction at beam energy E lab =112MeV, has been performed through in-beam gamma-ray spectroscopy. It revealed three signature-split bands. The yrast band based on πh 11/2 circle-times νi 13/2 configuration exhibits anomalous signature splitting (the unfavored signature Routhian lying lower than the favored one) whose magnitude Δe ' ∼25keV, is considerably reduced in contrast to sizable normal signature splitting Δe ' ∼125 and 60 keV observed in the yrast πh 11/2 bands of the neighboring odd-A 161,163 Lu nuclei, respectively. The signature inversion in this band occurs at spin ∼20ℎ (frequency=0.37MeV). The second signature-split band, observed above the band crossing associated with the alignment of a pair of i 13/2 quasineutrons, is a band based on the four-quasiparticle [πh 11/2 [523]7/2 - times νh 9/2 [521]3/2 - times(νi 13/2 ) 2 ], i.e., EABA p (B p ), configuration. The third signature-split band is also likely to be a four-quasiparticle band with configuration similar to the second band but involving F quasineutron, i.e., FABA p (B p ). The experimental results are discussed in comparison with the existing data in the neighboring nuclei and in the framework of the cranking shell model. copyright 1997 The American Physical Society

  1. Acute dysprosium toxicity to Daphnia pulex and Hyalella azteca and development of the biotic ligand approach

    Energy Technology Data Exchange (ETDEWEB)

    Vukov, Oliver, E-mail: vuko3930@mylaurier.ca [Biology Department, Wilfrid Laurier University, Waterloo, Ontario N2L 3C5 (Canada); Smith, D. Scott [Chemistry Department, Wilfrid Laurier University, Waterloo, Ontario N2L 3C5 (Canada); McGeer, James C. [Biology Department, Wilfrid Laurier University, Waterloo, Ontario N2L 3C5 (Canada)

    2016-01-15

    The toxicological understanding of rare earth elements (REEs) in the aquatic environment is very limited but of increasing concern. The objective of this research is to compare the toxicological effect of the REE dysprosium to the freshwater invertebrates Daphnia pulex and Hyalella azteca and in the more sensitive organism, understand the toxicity modifying influence of Ca, Na, Mg, pH and dissolved organic matter (DOM). Standard methods (Environment Canada) were followed for testing and culture in media of intermediate hardness (60 mg CaCO{sub 3} mg/L) at pH 7.8 with Ca at 0.5, Na 0.5, Mg 0.125 (mM) and 23 °C. Acute toxicity tests were done with <24 h old neonates for 48 h in the case of D. pulex and with 2–9 days old offspring for 96 h tests with Hyalella. The potential protective effect of cationic competition was tested with Ca (0.5–2.0 mM), Na (0.5–2.0 mM) and Mg (0.125–0.5 mM). The effect of pH (6.5–8.0) and Suwannee River DOM complexation (at dissolved organic carbon (DOC) concentrations of 9 and 13 mg C/L) were evaluated. Dissolved Dy concentrations were lower than total (unfiltered) indicating precipitation, particularly at higher concentrations. Acute toxicity of Dy to H. azteca and D. pulex revealed Hyalella to be 1.4 times more sensitive than Daphnia. Additions of Ca and Na but not Mg provided significant protection against Dy toxicity to Hyalella. Similarly, low pH was associated with reduction in toxicity. Exposures which were pH buffered with and without MOPS were significantly different and indicated that MOPS enhanced Dy toxicity. DOM also mitigated Dy toxicity. Biotic ligand based parameters (Log K values) were calculated based on free ion relationships as determined by geochemical equilibrium modeling software (WHAM ver. 7.02). The log K value for Dy{sup 3+} toxicity to Hyalella was 7.75 while the protective influence of Ca and Na were 3.95 and 4.10, respectively. This study contributes data towards the development of site specific

  2. Synthesis and characterization of phosphors based on calcium and magnesium silicates doped with europium and dysprosium

    International Nuclear Information System (INIS)

    Misso, Agatha Matos

    2016-01-01

    Ca and Mg silicates based phosphors were prepared by sol-gel method combined with the molten salts process. The gel of silica was obtained from Na 2 SiO 3 solution by using europium, dysprosium, calcium and magnesium chloride solutions. Therefore, those chlorides were homogeneously dispersed into the gel. The obtained gel was dried and heat treated to 900° C for 1h to allow the fusion of the present salts. Then it was water washed until negative test for Cl - , and dried. The reduction of the europium to Eu 2+ was performed under atmosphere of 5% of H 2 and 95% of Ar to 900° C for 3h, to reach CaMgSi 2 O 6 :Eu 2+ and CaMgSi 2 O 6 :Eu 2+ :Dy 3+ phosphors. Diopside was identified as main crystalline phase and quartz, as secondary phase from XRD (X-ray diffraction) patterns. SEM (scanning electron microscopy) micrographs, of the samples showed needles, spheres, leaves and rods of particles and agglomerates. Thermal analysis (TGA-DTGA) curves revealed that the crystallization temperature of CaMgSi 2 O 6 :Eu 2+ lies around 765° C. Photoluminescence spectroscopy of the phosphors was studied based on interconfigurational 4f N → 4f N-1 5d transition of Eu 2+ ion. The spectra of excitation showed 4f N → 4f N-1 5d transition of Eu 2+ ion broad band, related to the ligand to metal charge transfer transition (LMCT) O 2- (2p) → Eu 3+ in the 250 nm region, when the emission is monitored at 583,5 nm. It also presents the 4f ↔ 4f transitions of Eu 3+ ion bands, showing the 7 F 0 → 5 L 6 transition at 393 nm. From emission spectra with excitation monitored at 393 nm, it can be observed fine peaks between 570 and 750 nm which are characteristics of 5 D 0 → 7 F J (J = 0 - 5) transition of Eu 3+ ion, indicating that the Eu 3+ ion occupies a site with center of inversion. Finally, the obtained results indicate that the developed method is suitable to synthesize CaMgSi 2 O 6 :Eu 2+ and CaMgSi 2 O 6 :Eu 2+ :Dy 3+ phosphors, as it has been proposed. (author)

  3. Luminescence properties of dysprosium doped calcium magnesium silicate phosphor by solid state reaction method

    Energy Technology Data Exchange (ETDEWEB)

    Sahu, Ishwar Prasad, E-mail: ishwarprasad1986@gmail.com [School of Studies in Physics & Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Chandrakar, Priya; Baghel, R.N.; Bisen, D.P.; Brahme, Nameeta [School of Studies in Physics & Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Tamrakar, Raunak Kumar [Department of Applied Physics, Bhilai Institute of Technology, Durg, C.G. 491001 (India)

    2015-11-15

    Dysprosium doped calcium magnesium silicate (CaMgSi{sub 2}O{sub 6}:Dy{sup 3+}) white light emitting phosphor was synthesized by solid state reaction process. The crystal structure of sintered phosphor was monoclinic structure with space group C2/c. Chemical composition of the sintered CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor was confirmed by EDX. The prepared CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor was excited from 352 nm and their corresponding emission spectra were recorded at blue (470 nm), yellow (570 nm) and red (675 nm) line due to the {sup 4}F{sub 9/2} → {sup 6}H{sub 15/2}, {sup 4}F{sub 9/2} → {sup 6}H{sub 13/2}, {sup 4}F{sub 9/2} → {sup 6}H{sub 11/2} transitions of Dy{sup 3+} ions. The combination of these three emissions constituted as white light confirmed by the Commission Internationale de L'Eclairage (CIE) chromatic coordinate diagram. The possible mechanism of the white light emitting long lasting CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor was also investigated. Investigation on afterglow property show that phosphor held fast and slow decay process. The peak of mechanoluminescence (ML) intensity increases linearly with increasing impact velocity of the moving piston. Thus the present investigation indicates that the local piezoelectricity-induced electron bombardment model is responsible to produce ML in prepared CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor. - Highlights: • The crystal structure of CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor is consistent with standard monoclinic structure. • CIE coordinates of CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor is suitable as white light emitting phosphor. • The local piezoelectricity-induced electron bombardment model is responsible to produce ML in CaMgSi{sub 2}O{sub 6}:Dy{sup 3+} phosphor.

  4. An ICP AES method for determination of dysprosium and terbium in high purity yttrium oxide

    International Nuclear Information System (INIS)

    Rupawate, V.H.; Hareendran, K.N.; Roy, S.B.

    2011-01-01

    High purity yttrium finds interesting application in astronavigation, luminescence, nuclear energy and metallurgical industries. Most of these applications require yttrium oxide of highest purity. Consequently there is a need for production of high purity yttrium oxide. Separation and purification of yttrium from other rare earths is a challenging task due to their close chemical properties. Liquid-liquid extraction and ion exchange have been widely used in the production of yttrium oxide of highest purity. Determination of impurities, especially other rare earths, in ppm level is required for process development and chemical characterization of the high purity Y 2 O 3 . Many methods have been described in literature. However since the advent of ICP AES much work in this area has been carried out by this technique. This paper describes the work done for determination of dysprosium (Dy) and terbium (Tb) in yttrium oxide using a high resolution sequential ICP AES. Emission spectra of rare earth elements are very complex and due to this complexity it is important to select spectral interference free analyte lines for determination of rare earths in rare earth matrix. For the determination of Dy and Tb in Y 2 O 3 , sensitive lines of Dy and Tb are selected from the instrument wavelength table and spectral interference free emission lines for the determination is selected by scanning around the selected wavelengths using 5 g/L Y solution and 5 mg/L standard solutions of Dy and Tb prepared in 4% nitric acid. It is found 353.170 nm line of Dy and 350.917 nm line Tb is suitable for quantitative determination. The signal to background ratio increases with increase in matrix concentration, i.e. from 1 to 5 mg/L. The optimum forward power is determined and it is found to be 1100W for Dy and 1000W for Tb. The instrument is calibrated using matrix matched standards containing 5g/L of Y matrix. Samples are dissolved in nitric acid and Y concentration is maintained at 5g/L. Two

  5. Acute dysprosium toxicity to Daphnia pulex and Hyalella azteca and development of the biotic ligand approach

    International Nuclear Information System (INIS)

    Vukov, Oliver; Smith, D. Scott; McGeer, James C.

    2016-01-01

    The toxicological understanding of rare earth elements (REEs) in the aquatic environment is very limited but of increasing concern. The objective of this research is to compare the toxicological effect of the REE dysprosium to the freshwater invertebrates Daphnia pulex and Hyalella azteca and in the more sensitive organism, understand the toxicity modifying influence of Ca, Na, Mg, pH and dissolved organic matter (DOM). Standard methods (Environment Canada) were followed for testing and culture in media of intermediate hardness (60 mg CaCO 3 mg/L) at pH 7.8 with Ca at 0.5, Na 0.5, Mg 0.125 (mM) and 23 °C. Acute toxicity tests were done with <24 h old neonates for 48 h in the case of D. pulex and with 2–9 days old offspring for 96 h tests with Hyalella. The potential protective effect of cationic competition was tested with Ca (0.5–2.0 mM), Na (0.5–2.0 mM) and Mg (0.125–0.5 mM). The effect of pH (6.5–8.0) and Suwannee River DOM complexation (at dissolved organic carbon (DOC) concentrations of 9 and 13 mg C/L) were evaluated. Dissolved Dy concentrations were lower than total (unfiltered) indicating precipitation, particularly at higher concentrations. Acute toxicity of Dy to H. azteca and D. pulex revealed Hyalella to be 1.4 times more sensitive than Daphnia. Additions of Ca and Na but not Mg provided significant protection against Dy toxicity to Hyalella. Similarly, low pH was associated with reduction in toxicity. Exposures which were pH buffered with and without MOPS were significantly different and indicated that MOPS enhanced Dy toxicity. DOM also mitigated Dy toxicity. Biotic ligand based parameters (Log K values) were calculated based on free ion relationships as determined by geochemical equilibrium modeling software (WHAM ver. 7.02). The log K value for Dy 3+ toxicity to Hyalella was 7.75 while the protective influence of Ca and Na were 3.95 and 4.10, respectively. This study contributes data towards the development of site specific water quality

  6. Ocular Toxicity Profile of ST-162 and ST-168 as Novel Bifunctional MEK/PI3K Inhibitors.

    Science.gov (United States)

    Smith, Andrew; Pawar, Mercy; Van Dort, Marcian E; Galbán, Stefanie; Welton, Amanda R; Thurber, Greg M; Ross, Brian D; Besirli, Cagri G

    2018-04-30

    ST-162 and ST-168 are small-molecule bifunctional inhibitors of MEK and PI3K signaling pathways that are being developed as novel antitumor agents. Previous small-molecule and biologic MEK inhibitors demonstrated ocular toxicity events that were dose limiting in clinical studies. We evaluated in vitro and in vivo ocular toxicity profiles of ST-162 and ST-168. Photoreceptor cell line 661W and adult retinal pigment epithelium cell line ARPE-19 were treated with increasing concentrations of bifunctional inhibitors. Western blots, cell viability, and caspase activity assays were performed to evaluate MEK and PI3K inhibition and dose-dependent in vitro toxicity, and compared with monotherapy. In vivo toxicity profile was assessed by intravitreal injection of ST-162 and ST-168 in Dutch-Belted rabbits, followed by ocular examination and histological analysis of enucleated eyes. Retinal cell lines treated with ST-162 or ST-168 exhibited dose-dependent inhibition of MEK and PI3K signaling. Compared with inhibition by monotherapies and their combinations, bifunctional inhibitors demonstrated reduced cell death and caspase activity. In vivo, both bifunctional inhibitors exhibited a more favorable toxicity profile when compared with MEK inhibitor PD0325901. Novel MEK and PI3K bifunctional inhibitors ST-162 and ST-168 demonstrate favorable in vitro and in vivo ocular toxicity profiles, supporting their further development as potential therapeutic agents targeting multiple aggressive tumors.

  7. Dual responsive dysprosium-doped hydroxyapatite particles and toxicity reduction after functionalization with folic and glucuronic acids.

    Science.gov (United States)

    Sánchez Lafarga, Ana Karen; Pacheco Moisés, Fermín P; Gurinov, Andrey; Ortiz, Genaro Gabriel; Carbajal Arízaga, Gregorio Guadalupe

    2015-03-01

    The development of probes for biomedical applications demands materials with low toxicity levels besides fluorescence or magnetic properties to be detected by confocal microscopes or MRI resonators. Several drug delivery systems or other biomedical materials prepared with hydroxyapatite have been proposed, however, toxicity effects might arise when the size of particles is nanometric. In this study, hydroxyapatite functionalized with glucuronic or folic acids presented lower oxidative stress, measured from lipoperoxides and nitric oxide indicators in rats than pure hydroxyapatite. In separated experiments, hydroxyapatite was doped with dysprosium cations by coprecipitation producing a single crystal phase with fluorescent properties easily visualized by confocal microscopy when excited at 488nm. These particles also presented the ability to modify the proton relaxation time in T1 maps collected by magnetic resonance imaging. These modified hydroxyapatite nanoparticles could be candidates to design bimodal probes with low toxicity. Copyright © 2014 Elsevier B.V. All rights reserved.

  8. Magnetic anisotropy of dysprosium(III) in a low-symmetry environment: a theoretical and experimental investigation.

    Science.gov (United States)

    Bernot, Kevin; Luzon, Javier; Bogani, Lapo; Etienne, Mael; Sangregorio, Claudio; Shanmugam, Muralidharan; Caneschi, Andrea; Sessoli, Roberta; Gatteschi, Dante

    2009-04-22

    A mixed theoretical and experimental approach was used to determine the local magnetic anisotropy of the dysprosium(III) ion in a low-symmetry environment. The susceptibility tensor of the monomeric species having the formula [Dy(hfac)(3)(NIT-C(6)H(4)-OEt)(2)], which contains nitronyl nitroxide (NIT-R) radicals, was determined at various temperatures through angle-resolved magnetometry. These results are in agreement with ab initio calculations performed using the complete active space self-consistent field (CASSCF) method, validating the predictive power of this theoretical approach for complex systems containing rare-earth ions, even in low-symmetry environments. Susceptibility measurements performed with the applied field along the easy axis eventually permitted a detailed analysis of the temperature and field dependence of the magnetization, providing evidence that the Dy ion transmits an antiferromagnetic interaction between radicals but that the Dy-radical interaction is ferromagnetic.

  9. Watt-level dysprosium fiber laser at 3.15  μm with 73% slope efficiency.

    Science.gov (United States)

    Woodward, R I; Majewski, M R; Bharathan, G; Hudson, D D; Fuerbach, A; Jackson, S D

    2018-04-01

    Rare-earth-doped fiber lasers are emerging as promising high-power mid-infrared sources for the 2.6-3.0 μm and 3.3-3.8 μm regions based on erbium and holmium ions. The intermediate wavelength range, however, remains vastly underserved, despite prospects for important manufacturing and defense applications. Here, we demonstrate the potential of dysprosium-doped fiber to solve this problem, with a simple in-band pumped grating-stabilized linear cavity generating up to 1.06 W at 3.15 μm. A slope efficiency of 73% with respect to launched power (77% relative to absorbed power) is achieved-the highest value for any mid-infrared fiber laser to date, to the best of our knowledge. Opportunities for further power and efficiency scaling are also discussed.

  10. On-line complexation/cloud point preconcentration for the sensitive determination of dysprosium in urine by flow injection inductively coupled plasma-optical emission spectrometry

    International Nuclear Information System (INIS)

    Ortega, Claudia; Cerutti, Soledad; Silva, Maria F.; Olsina, Roberto A.; Martinez, Luis D.

    2003-01-01

    An on-line dysprosium preconcentration and determination system based on the hyphenation of cloud point extraction (CPE) to flow injection analysis (FIA) associated with ICP-OES was studied. For the preconcentration of dysprosium, a Dy(III)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex was formed on-line at pH 9.22 in the presence of nonionic micelles of PONPE-7.5. The micellar system containing the complex was thermostated at 30 C in order to promote phase separation, and the surfactant-rich phase was retained in a microcolumn packed with cotton at pH 9.2. The surfactant-rich phase was eluted with 4 mol L -1 nitric acid at a flow rate of 1.5 mL min -1 , directly in the nebulizer of the plasma. An enhancement factor of 50 was obtained for the preconcentration of 50 mL of sample solution. The detection limit value for the preconcentration of 50 mL of aqueous solution of Dy was 0.03 μg L -1 . The precision for 10 replicate determinations at the 2.0 μg L -1 Dy level was 2.2% relative standard deviation (RSD), calculated from the peak heights obtained. The calibration graph using the preconcentration system for dysprosium was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 100 μg L -1 . The method was successfully applied to the determination of dysprosium in urine. (orig.)

  11. Graphite furnace atomic absorption spectrometry with a tantalum boat for the determination of yttrium, samarium, and dysprosium in a mish metal

    International Nuclear Information System (INIS)

    Daidoji, Hidehiro; Tamura, Shohei

    1982-01-01

    The determination of yttrium, samarium, and dysprodium by means of graphite-furnace atomic absorption spectrometry (AAS) was studied by a tantalum boat inserted into a graphite tube atomizer. These elements could not be determined by the use of a commercial graphite tube, In the atomization from a tantalum boat, better analytical sensitivities and negligible memory effects for these rare earths are obtained. The analytical sensitivities of yttrium, samarium, and dysprodium with the tantalum boat were 0.60 ng, 0.86 ng, and 0.17 ng respectively. This method was applied for the determination of yttrium, samarium, and dysprosium in a mish metal. The measurements were performed with slightly acidified solutions (0.01 mol dm 3 HCI or HNO 3 ). The sensitivities and the precisions for these elements decreased with increasing acid concentration. An enhancement in the sensitivities of yttrium and dysprosium upon the addition of a large excess of lanthanum, neodymium, and praseodymium salts were observed. The yttrium, samarium, and dysprosium in a mish metal were determined with both analytical curves of standard solutions containing an excess of lanthanum, cerium, and neodymium ions and of the standard addition. The precisions for this work were in the 3 - 9.3% range. (author)

  12. 45 CFR 162.925 - Additional requirements for health plans.

    Science.gov (United States)

    2010-10-01

    ... clearinghouse to receive, process, or transmit a standard transaction may not charge fees or costs in excess of... RELATED REQUIREMENTS ADMINISTRATIVE REQUIREMENTS General Provisions for Transactions § 162.925 Additional... transaction as a standard transaction, the health plan must do so. (2) A health plan may not delay or reject a...

  13. 26 CFR 1.162-10 - Certain employee benefits.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Certain employee benefits. 1.162-10 Section 1... employee benefits. (a) In general. Amounts paid or accrued by a taxpayer on account of injuries received by...) for the benefit of employees, their families, and dependents, at least medical or hospital care, and...

  14. 7 CFR 905.162 - Repacking certificate of privilege.

    Science.gov (United States)

    2010-01-01

    ... 905.162 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ORANGES..., address and Florida citrus fruit dealer license number of the applicant; approximate number of boxes to be...

  15. 40 CFR 35.162 - Basis for allotment.

    Science.gov (United States)

    2010-07-01

    ... STATE AND LOCAL ASSISTANCE Environmental Program Grants Water Pollution Control (section 106) § 35.162... are presented in Table 1 of this section, with their associated elements, sub-elements, and supporting... made on the basis of the cumulative change in the Consumer Price Index (CPI), published by the U.S...

  16. 21 CFR 131.162 - Acidified sour cream.

    Science.gov (United States)

    2010-04-01

    ... HUMAN CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.162.... (c) Methods of analysis. Referenced methods in paragraphs (c) (1) and (2) of this section are from “Official Methods of Analysis of the Association of Official Analytical Chemists,” 13th Ed. (1980), which is...

  17. 26 CFR 1.162-18 - Illegal bribes and kickbacks.

    Science.gov (United States)

    2010-04-01

    ... bribe (whether or not illegal) made on or after December 10, 1971, by any provider of services, supplier... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Illegal bribes and kickbacks. 1.162-18 Section 1... bribes and kickbacks. (a) Illegal payments to government officials or employees—(1) In general. No...

  18. 27 CFR 9.162 - Sta. Rita Hills.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Sta. Rita Hills. 9.162.... Rita Hills. (a) Name. The name of the viticultural area described in this section is “Sta. Rita Hills”. For purposes of part 4 of this chapter, “Sta. Rita Hills” is a term of viticultural significance. (b...

  19. Moments of inertia in 162Yb at very high spins

    International Nuclear Information System (INIS)

    Simon, R.S.; Banaschik, M.V.; Colombani, P.; Soroka, D.P.; Stephens, F.S.; Diamond, R.M.

    1976-01-01

    Two methods have been used to obtain values of the effective moment of inertia of very-high-spin (20h-bar--50h-bar) states populated in heavy-ion compound-nucleus reactions. The 162 Yb nucleus studied has effective moments of inertia smaller than, but approaching, the rigid-body estimate

  20. 40 CFR 80.162 - Additive compositional data.

    Science.gov (United States)

    2010-07-01

    ... detergent production quality control. EPA will respond to such requests in writing; the additional... variability is required, and provide evidence that the production detergent will perform adequately throughout... (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Detergent Gasoline § 80.162 Additive compositional data...

  1. Workplace testing of the new single sphere neutron spectrometer based on Dysprosium activation foils (Dy-SSS)

    International Nuclear Information System (INIS)

    Bedogni, R.; Gómez-Ros, J.M.; Esposito, A.; Gentile, A.; Chiti, M.; Palacios-Pérez, L.; Angelone, M.; Tana, L.

    2012-01-01

    A photon insensitive passive neutron spectrometer consisting of a single moderating polyethylene sphere with Dysprosium activation foils arranged along three perpendicular axes was designed by CIEMAT and INFN. The device is called Dy-SSS (Dy foil-based Single Sphere Spectrometer). It shows nearly isotropic response in terms of neutron fluence up to 20 MeV. The first prototype, previously calibrated with 14 MeV neutrons, has been recently tested in workplaces having different energy and directional distributions. These are a 2.5 MeV nearly mono-chromatic and mono-directional beam available at the ENEA Frascati Neutron Generator (FNG) and the photo-neutron field produced in a 15 MV Varian CLINAC DHX medical accelerator, located in the Ospedale S. Chiara (Pisa). Both neutron spectra are known through measurements with a Bonner Sphere Spectrometer. In both cases the experimental response of the Dy-SSS agrees with the reference data. Moreover, it is demonstrated that the spectrometric capability of the new device are independent from the directional distribution of the neutron field. This opens the way to a new generation of moderation-based neutron instruments, presenting all advantages of the Bonner sphere spectrometer without the disadvantage of the repeated exposures. This concept is being developed within the NESCOFI@BTF project of INFN (Commissione Scientifica Nazionale 5).

  2. Workplace testing of the new single sphere neutron spectrometer based on Dysprosium activation foils (Dy-SSS)

    Science.gov (United States)

    Bedogni, R.; Gómez-Ros, J. M.; Esposito, A.; Gentile, A.; Chiti, M.; Palacios-Pérez, L.; Angelone, M.; Tana, L.

    2012-08-01

    A photon insensitive passive neutron spectrometer consisting of a single moderating polyethylene sphere with Dysprosium activation foils arranged along three perpendicular axes was designed by CIEMAT and INFN. The device is called Dy-SSS (Dy foil-based Single Sphere Spectrometer). It shows nearly isotropic response in terms of neutron fluence up to 20 MeV. The first prototype, previously calibrated with 14 MeV neutrons, has been recently tested in workplaces having different energy and directional distributions. These are a 2.5 MeV nearly mono-chromatic and mono-directional beam available at the ENEA Frascati Neutron Generator (FNG) and the photo-neutron field produced in a 15 MV Varian CLINAC DHX medical accelerator, located in the Ospedale S. Chiara (Pisa). Both neutron spectra are known through measurements with a Bonner Sphere Spectrometer. In both cases the experimental response of the Dy-SSS agrees with the reference data. Moreover, it is demonstrated that the spectrometric capability of the new device are independent from the directional distribution of the neutron field. This opens the way to a new generation of moderation-based neutron instruments, presenting all advantages of the Bonner sphere spectrometer without the disadvantage of the repeated exposures. This concept is being developed within the NESCOFI@BTF project of INFN (Commissione Scientifica Nazionale 5).

  3. Workplace testing of the new single sphere neutron spectrometer based on Dysprosium activation foils (Dy-SSS)

    Energy Technology Data Exchange (ETDEWEB)

    Bedogni, R., E-mail: roberto.bedogni@lnf.infn.it [INFN-LNF (Frascati National Laboratories), Via E. Fermi n. 40-00044 Frascati (Italy); Gomez-Ros, J.M. [INFN-LNF (Frascati National Laboratories), Via E. Fermi n. 40-00044 Frascati (Italy); CIEMAT, Av. Complutense 40, 28040 Madrid (Spain); Esposito, A.; Gentile, A.; Chiti, M.; Palacios-Perez, L. [INFN-LNF (Frascati National Laboratories), Via E. Fermi n. 40-00044 Frascati (Italy); Angelone, M. [ENEA C.R. Frascati, C.P. 65, 00044 Frascati (Italy); Tana, L. [A.O. Universitaria Pisana-Ospedale S. Chiara, Via Bonanno Pisano, Pisa (Italy)

    2012-08-21

    A photon insensitive passive neutron spectrometer consisting of a single moderating polyethylene sphere with Dysprosium activation foils arranged along three perpendicular axes was designed by CIEMAT and INFN. The device is called Dy-SSS (Dy foil-based Single Sphere Spectrometer). It shows nearly isotropic response in terms of neutron fluence up to 20 MeV. The first prototype, previously calibrated with 14 MeV neutrons, has been recently tested in workplaces having different energy and directional distributions. These are a 2.5 MeV nearly mono-chromatic and mono-directional beam available at the ENEA Frascati Neutron Generator (FNG) and the photo-neutron field produced in a 15 MV Varian CLINAC DHX medical accelerator, located in the Ospedale S. Chiara (Pisa). Both neutron spectra are known through measurements with a Bonner Sphere Spectrometer. In both cases the experimental response of the Dy-SSS agrees with the reference data. Moreover, it is demonstrated that the spectrometric capability of the new device are independent from the directional distribution of the neutron field. This opens the way to a new generation of moderation-based neutron instruments, presenting all advantages of the Bonner sphere spectrometer without the disadvantage of the repeated exposures. This concept is being developed within the NESCOFI@BTF project of INFN (Commissione Scientifica Nazionale 5).

  4. Lifetimes of high-spin states in {sup 162}Yb

    Energy Technology Data Exchange (ETDEWEB)

    Carpenter, M.P.; Janssens, R.V.F.; Henry, R.G. [and others

    1995-08-01

    A measurement on lifetimes of high-spin states in the yrast and near-yrast rotational bands in {sup 162}Yb was carried out at ATLAS in order to determine the evolution of collectivity as a function of angular momentum using the {sup 126}Te({sup 40}Ar,4n){sup 162}Yb reaction at 170 MeV. Previous lifetime measurements in the {sup 164,166,168}Yb isotopes showed a dramatic decrease in the transition quadrupole moment Q{sub t} with increasing spin. It was suggested that this decrease in Q{sub t} is brought about by the rotationally-induced deoccupation of high-j configurations, mainly i{sub 13/2} neutrons. If this interpretation is correct, the heavier isotopes should have a larger decrease in Q{sub t} than the lighter mass nuclides due to the position of the Fermi surface in the i{sub 13/2} subshell. Indeed, {sup 160}Yb does not show a clear decrease in Q{sub t} at high spin. No high spin lifetime information exists for {sup 162}Yb, thus this experiment fills the gap of measured Q{sub t}`s in the light Yb series. The data is currently being analyzed.

  5. 42 CFR 415.162 - Determining payment for physician services furnished to beneficiaries in teaching hospitals.

    Science.gov (United States)

    2010-10-01

    ... furnished to beneficiaries in teaching hospitals. 415.162 Section 415.162 Public Health CENTERS FOR MEDICARE... BY PHYSICIANS IN PROVIDERS, SUPERVISING PHYSICIANS IN TEACHING SETTINGS, AND RESIDENTS IN CERTAIN SETTINGS Physician Services in Teaching Settings § 415.162 Determining payment for physician services...

  6. 33 CFR 162.134 - Connecting waters from Lake Huron to Lake Erie; traffic rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; traffic rules. 162.134 Section 162.134 Navigation and Navigable Waters COAST GUARD... REGULATIONS § 162.134 Connecting waters from Lake Huron to Lake Erie; traffic rules. (a) Detroit River. The...

  7. 33 CFR 162.132 - Connecting waters from Lake Huron to Lake Erie; communications rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; communications rules. 162.132 Section 162.132 Navigation and Navigable Waters COAST... NAVIGATION REGULATIONS § 162.132 Connecting waters from Lake Huron to Lake Erie; communications rules. (a...

  8. 33 CFR 162.130 - Connecting waters from Lake Huron to Lake Erie; general rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; general rules. 162.130 Section 162.130 Navigation and Navigable Waters COAST GUARD... REGULATIONS § 162.130 Connecting waters from Lake Huron to Lake Erie; general rules. (a) Purpose. The...

  9. 33 CFR 162.138 - Connecting waters from Lake Huron to Lake Erie; speed rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; speed rules. 162.138 Section 162.138 Navigation and Navigable Waters COAST GUARD... REGULATIONS § 162.138 Connecting waters from Lake Huron to Lake Erie; speed rules. (a) Maximum speed limit for...

  10. 33 CFR 162.136 - Connecting waters from Lake Huron to Lake Erie; anchorage grounds.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; anchorage grounds. 162.136 Section 162.136 Navigation and Navigable Waters COAST GUARD... REGULATIONS § 162.136 Connecting waters from Lake Huron to Lake Erie; anchorage grounds. (a) In the Detroit...

  11. 33 CFR 162.140 - Connecting waters from Lake Huron to Lake Erie; miscellaneous rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Connecting waters from Lake Huron to Lake Erie; miscellaneous rules. 162.140 Section 162.140 Navigation and Navigable Waters COAST... NAVIGATION REGULATIONS § 162.140 Connecting waters from Lake Huron to Lake Erie; miscellaneous rules. (a...

  12. 27 CFR 70.162 - Levy and distraint on salary and wages.

    Science.gov (United States)

    2010-04-01

    ... salary and wages. 70.162 Section 70.162 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX... § 70.162 Levy and distraint on salary and wages. (a) Notice of intent to levy. Levy may be made for any... salary or wages. A levy on salary or wages is continuous from the time of the levy until the liability...

  13. 33 CFR 165.162 - Safety Zone: New York Super Boat Race, Hudson River, New York.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zone: New York Super Boat Race, Hudson River, New York. 165.162 Section 165.162 Navigation and Navigable Waters COAST GUARD... § 165.162 Safety Zone: New York Super Boat Race, Hudson River, New York. (a) Regulated area. The...

  14. 33 CFR 162.125 - Sturgeon Bay and the Sturgeon Bay Ship Canal, Wisc.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Sturgeon Bay and the Sturgeon Bay Ship Canal, Wisc. 162.125 Section 162.125 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY INLAND WATERWAYS NAVIGATION REGULATIONS § 162.125 Sturgeon Bay and the Sturgeon Bay Ship...

  15. 19 CFR 162.65 - Penalties for failure to manifest narcotic drugs or marihuana.

    Science.gov (United States)

    2010-04-01

    ... or marihuana. 162.65 Section 162.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Substances, Narcotics, and Marihuana § 162.65 Penalties for failure to manifest narcotic drugs or marihuana. (a) Cargo or baggage containing unmanifested narcotic drugs or marihuana. When a package of regular...

  16. 28 CFR 0.162 - Offers which may be rejected by Assistant Attorneys General.

    Science.gov (United States)

    2010-07-01

    ... Attorneys General. 0.162 Section 0.162 Judicial Administration DEPARTMENT OF JUSTICE ORGANIZATION OF THE..., Penalties, and Forfeitures § 0.162 Offers which may be rejected by Assistant Attorneys General. Each Assistant Attorney General is authorized, with respect to matters assigned to his division or office, to...

  17. 40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

    Science.gov (United States)

    2010-07-01

    ... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

  18. Oxide perovskites with tetravalent dysprosium and compounds of the type Ba/sub 3/RE/sub 4/O/sub 9/ (RE = Rare Earth Element)

    Energy Technology Data Exchange (ETDEWEB)

    Brauer, G; Kristen, H [Freiburg Univ. (Germany, F.R.)

    1980-03-01

    In analogy to our investigations concerning tetravalent Nd in oxide perovskites, we also tried to stabilize dysprosium(IV) by incorporation in host-lattices with the perovskite structure. As host-lattices we used BaCeO/sub 3/, BaTbO/sub 3/, and SrTbO/sub 3/. Only in Ba(Ce, Dy)O/sub 3/ we could trace Dy(IV) with certainty. Among the prepared mixed oxides, also the phase Ba/sub 3/Dy/sub 4/O/sub 9/ occured. The lattice parameters of several phases of this latter type were redetermined.

  19. Effect of solvents on relation of intensities of bands of luminescence spectra of terbium and dysprosium ions in solutions of their complexes with acetoacetic ester

    International Nuclear Information System (INIS)

    Kononenko, L.I.; Bel'tyukova, S.V.; Meshkova, S.B.; Kravchenko, T.B.; Poluehktov, N.S.

    1978-01-01

    An investigation is made of the effect of different solvents on the ratio of the intensity of luminescence spectrum bands of terbium and dysprosium ions, corresponding and not corresponding to ''supersensitive'' transitions in complex compounds with acetoacetic ether. A dependence is established between these values and the dielectric constant of the solvent, and also parallels in their changes, which indicate the similar manifestation of the effect of solvents in both elements. A correlation is observed between ratios of the intensity of luminescence spectrum bands and values of forces of neodymium complex absorption band oscillators in different solvents

  20. Optical amplifier operating at 1.3 microns useful for telecommunications and based on dysprosium-doped metal chloride host materials

    Energy Technology Data Exchange (ETDEWEB)

    Page, R.H.; Schaffers, K.I.; Payne, S.A.; Krupke, W.F.; Beach, R.J.

    1997-12-02

    Dysprosium-doped metal chloride materials offer laser properties advantageous for use as optical amplifiers in the 1.3 {micro}m telecommunications fiber optic network. The upper laser level is characterized by a millisecond lifetime, the host material possesses a moderately low refractive index, and the gain peak occurs near 1.31 {micro}m. Related halide materials, including bromides and iodides, are also useful. The Dy{sup 3+}-doped metal chlorides can be pumped with laser diodes and yield 1.3 {micro}m signal gain levels significantly beyond those currently available. 9 figs.

  1. Optical amplifier operating at 1.3 microns useful for telecommunications and based on dysprosium-doped metal chloride host materials

    Energy Technology Data Exchange (ETDEWEB)

    Page, Ralph H. (San Ramon, CA); Schaffers, Kathleen I. (Pleasanton, CA); Payne, Stephen A. (Castro Valley, CA); Krupke, William F. (Pleasanton, CA); Beach, Raymond J. (Livermore, CA)

    1997-01-01

    Dysprosium-doped metal chloride materials offer laser properties advantageous for use as optical amplifiers in the 1.3 .mu.m telecommunications fiber optic network. The upper laser level is characterized by a millisecond lifetime, the host material possesses a moderately low refractive index, and the gain peak occurs near 1.31 .mu.m. Related halide materials, including bromides and iodides, are also useful. The Dy.sup.3+ -doped metal chlorides can be pumped with laser diodes and yield 1.3 .mu.m signal gain levels significantly beyond those currently available.

  2. Identification, expression and phylogenetic analysis of EgG1Y162 from Echinococcus granulosus

    Science.gov (United States)

    Zhang, Fengbo; Ma, Xiumin; Zhu, Yuejie; Wang, Hongying; Liu, Xianfei; Zhu, Min; Ma, Haimei; Wen, Hao; Fan, Haining; Ding, Jianbing

    2014-01-01

    Objective: This study was to clone, identify and analyze the characteristics of egG1Y162 gene from Echinococcus granulosus. Methods: Genomic DNA and total RNAs were extracted from four different developmental stages of protoscolex, germinal layer, adult and egg of Echinococcus granulosus, respectively. Fluorescent quantitative PCR was used for analyzing the expression of egG1Y162 gene. Prokaryotic expression plasmid of pET41a-EgG1Y162 was constructed to express recombinant His-EgG1Y162 antigen. Western blot analysis was performed to detect antigenicity of EgG1Y162 antigen. Gene sequence, amino acid alignment and phylogenetic tree of EgG1Y162 were analyzed by BLAST, online Spidey and MEGA4 software, respectively. Results: EgG1Y162 gene was expressed in four developmental stages of Echinococcus granulosus. And, egG1Y162 gene expression was the highest in the adult stage, with the relative value of 19.526, significantly higher than other three stages. Additionally, Western blot analysis revealed that EgG1Y162 recombinant protein had good reaction with serum samples from Echinococcus granulosus infected human and dog. Moreover, EgG1Y162 antigen was phylogenetically closest to EmY162 antigen, with the similarity over 90%. Conclusion: Our study identified EgG1Y162 antigen in Echinococcus granulosus for the first time. EgG1Y162 antigen had a high similarity with EmY162 antigen, with the genetic differences mainly existing in the intron region. And, EgG1Y162 recombinant protein showed good antigenicity. PMID:25337206

  3. Identification, expression and phylogenetic analysis of EgG1Y162 from Echinococcus granulosus.

    Science.gov (United States)

    Zhang, Fengbo; Ma, Xiumin; Zhu, Yuejie; Wang, Hongying; Liu, Xianfei; Zhu, Min; Ma, Haimei; Wen, Hao; Fan, Haining; Ding, Jianbing

    2014-01-01

    This study was to clone, identify and analyze the characteristics of egG1Y162 gene from Echinococcus granulosus. Genomic DNA and total RNAs were extracted from four different developmental stages of protoscolex, germinal layer, adult and egg of Echinococcus granulosus, respectively. Fluorescent quantitative PCR was used for analyzing the expression of egG1Y162 gene. Prokaryotic expression plasmid of pET41a-EgG1Y162 was constructed to express recombinant His-EgG1Y162 antigen. Western blot analysis was performed to detect antigenicity of EgG1Y162 antigen. Gene sequence, amino acid alignment and phylogenetic tree of EgG1Y162 were analyzed by BLAST, online Spidey and MEGA4 software, respectively. EgG1Y162 gene was expressed in four developmental stages of Echinococcus granulosus. And, egG1Y162 gene expression was the highest in the adult stage, with the relative value of 19.526, significantly higher than other three stages. Additionally, Western blot analysis revealed that EgG1Y162 recombinant protein had good reaction with serum samples from Echinococcus granulosus infected human and dog. Moreover, EgG1Y162 antigen was phylogenetically closest to EmY162 antigen, with the similarity over 90%. Our study identified EgG1Y162 antigen in Echinococcus granulosus for the first time. EgG1Y162 antigen had a high similarity with EmY162 antigen, with the genetic differences mainly existing in the intron region. And, EgG1Y162 recombinant protein showed good antigenicity.

  4. Determination of Diclofenac on a Dysprosium Nanowire- Modified Carbon Paste Electrode Accomplished in a Flow Injection System by Advanced Filtering

    Directory of Open Access Journals (Sweden)

    Ali Akbar Moosavi-Movahedi

    2009-09-01

    Full Text Available A new detection technique called Fast Fourier Transform Square-Wave Voltammetry (FFT SWV is based on measurements of electrode admittance as a function of potential. The response of the detector (microelectrode, which is generated by a redox processes, is fast, which makes the method suitable for most applications involving flowing electrolytes. The carbon paste electrode was modified by nanostructures to improve sensitivity. Synthesized dysprosium nanowires provide a more effective nanotube-like surface [1-4] so they are good candidates for use as a modifier for electrochemical reactions. The redox properties of diclofenac were used for its determination in human serum and urine samples. The support electrolyte that provided a more defined and intense peak current for diclofenac determination was a 0.05 mol L−1 acetate buffer pH = 4.0. The drug presented an irreversible oxidation peak at 850 mV vs. Ag/AgCl on a modified nanowire carbon paste electrode which produced high current and reduced the oxidation potential by about 100 mV. Furthermore, the signal-to-noise ratio was significantly increased by application of a discrete Fast Fourier Transform (FFT method, background subtraction and two-dimensional integration of the electrode response over a selected potential range and time window. To obtain the much sensivity the effective parameters such as frequency, amplitude and pH was optimized. As a result, CDL of 2.0 × 10−9 M and an LOQ of 5.0 × 10−9 M were found for the determination for diclofenac. A good recovery was obtained for assay spiked urine samples and a good quantification of diclofenac was achieved in a commercial formulation.

  5. On the annealing behaviour of dysprosium ion implanted nickel: a combined study using Rutherford backscattering, transmission electron microscopy, and total current spectroscopy

    International Nuclear Information System (INIS)

    Chadderton, L.T.; Johnson, E.

    1977-01-01

    Despite continuing improvements in applications of the analytical method of Rutherford backscattering (RBS) to solid state physics it is recognized that more complete information can be obtained if other techniques - for example transmission electron microscopy (TEM) - are employed simultaneously. Experiments are described in which a combined RBS and TEM study of the annealing of nickel, rendered amorphous by implantation of 20 keV dysprosium ions is supplemented with a completely new technique - total current spectroscopy (TCS). In TCS low energy electrons (0-15 eV) are used to probe the damaged nickel. Observations have been made during annealing of both the reappearance of the bulk band structure of the metal and of a 'surface peak' which is highly sensitive to the recovery process. Changes in the height of the surface peak reveal three sharp annealing stages, the first two being preceded by reverse annealing which correlates well with RBS and TEM results. The first annealing stage - following the amorphous to crystalline transition - may be associated with electronic effects in the vicinity of the Curie point. Changes in the position of the surface peak allow one to trace the diffusion of dysprosium to the surface. Quantum mechanical resonances at the damage/crystal interface have also been followed throughout annealing. The initially amorphous layer (approximately 2.2nm) increases in thickness slightly during recovery. (Auth.)

  6. An Operationally Simple Method for Separating the Rare-Earth Elements Neodymium and Dysprosium.

    Science.gov (United States)

    Bogart, Justin A; Lippincott, Connor A; Carroll, Patrick J; Schelter, Eric J

    2015-07-06

    Rare-earth metals are critical components of electronic materials and permanent magnets. Recycling of consumer materials is a promising new source of rare earths. To incentivize recycling there is a clear need for simple methods for targeted separations of mixtures of rare-earth metal salts. Metal complexes of a tripodal nitroxide ligand [{(2-(t) BuNO)C6 H4 CH2 }3 N](3-) (TriNOx(3-) ), feature a size-sensitive aperture formed of its three η(2) -(N,O) ligand arms. Exposure of metal cations in the aperture induces a self-associative equilibrium comprising [M(TriNOx)thf]/ [M(TriNOx)]2 (M=rare-earth metal). Differences in the equilibrium constants (Keq ) for early and late metals enables simple Nd/Dy separations through leaching with a separation ratio SNd/Dy =359. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. An operationally simple method for separating the rare-earth elements neodymium and dysprosium

    Energy Technology Data Exchange (ETDEWEB)

    Bogart, Justin A.; Lippincott, Connor A.; Carroll, Patrick J.; Schelter, Eric J. [Department of Chemistry, University of Pennsylvania, Philadelphia, PA (United States)

    2015-07-06

    Rare-earth metals are critical components of electronic materials and permanent magnets. Recycling of consumer materials is a promising new source of rare earths. To incentivize recycling there is a clear need for simple methods for targeted separations of mixtures of rare-earth metal salts. Metal complexes of a tripodal nitroxide ligand [{(2-"tBuNO)C_6H_4CH_2}{sub 3}N]{sup 3-} (TriNOx{sup 3-}), feature a size-sensitive aperture formed of its three η{sup 2}-(N,O) ligand arms. Exposure of metal cations in the aperture induces a self-associative equilibrium comprising [M(TriNOx)thf]/[M(TriNOx)]{sub 2} (M=rare-earth metal). Differences in the equilibrium constants (K{sub eq}) for early and late metals enables simple Nd/Dy separations through leaching with a separation ratio S{sub Nd/Dy}=359. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Four new dysprosium and neodymium octamolybdate hydrates: assembly of RE2(Mo8O27) sheets and topotactic transformations.

    Science.gov (United States)

    Kuang, Xiaojun; Evans, Ivana R

    2010-07-05

    Four new Dy and Nd hydrated octamolybdate materials have been prepared: [Dy(2)(H(2)O)(12)](Mo(8)O(27)) x 8 H(2)O, [Dy(2)(H(2)O)(6)](Mo(8)O(27)), [Nd(2)(H(2)O)(12)](Mo(8)O(27)) x 6 H(2)O, and [Nd(2)(H(2)O)(6)]Mo(8)O(27) x 3 H(2)O. They adopt one known and three new structure types, which we have determined ab initio from powder X-ray diffraction data. The four compounds contain the same basic structural building block, in the form of RE(2)Mo(8)O(27) (RE = Dy, Nd) chains, which are arranged differently for the two rare earths in the fully hydrated precursor materials. [Dy(2)(H(2)O)(12)](Mo(8)O(27)) x 8 H(2)O comprises isolated Dy(2)Mo(8)O(27) chains assembled in a zigzag manner along the a axis with interspersed crystallized water molecules, which differs from the parallel arrangements of isolated Nd(2)Mo(8)O(27) chains in [Nd(2)(H(2)O)(12)](Mo(8)O(27)) x 6 H(2)O. Partial dehydration of the two precursors leads to new phases [Dy(2)(H(2)O)(6)](Mo(8)O(27)) and [Nd(2)(H(2)O)(6)]Mo(8)O(27) x 3 H(2)O, respectively, prior to complete dehydration, which leads to initially amorphous and eventually crystalline rare-earth molybdenum mixed metal oxides. Both initial transformations occur topotactically. Partial dehydration of the Dy phase condenses the assembly of the Dy(2)Mo(8)O(27) chains principally along the a axis, leading to a 3-dimensional (3D) framework, with each Dy bridging two (Mo(8)O(27))(6-) sheets in the product. The partial dehydration of the Nd precursor condenses the assembly of Nd(2)Mo(8)O(27) chains along the [110] axis, leading to a 3D framework where each Nd bridges three (Mo(8)O(27))(6-) units. Both new dysprosium octamolybdates adopt noncentrosymmetric polar structures in space group P2(1) and are second harmonic generation (SHG) active.

  9. Microstructure and thermal properties of dysprosium and thulium co-doped barium titanate ceramics for high performance multilayer ceramic capacitors

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jinseong; Kim, Dowan; Noh, Taimin [School of Materials Science and Engineering, Pusan National University, Busan 609-735 (Korea, Republic of); Ahn, Byungmin [Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-0241 (United States); Lee, Heesoo, E-mail: heesoo@pusan.ac.kr [School of Materials Science and Engineering, Pusan National University, Busan 609-735 (Korea, Republic of)

    2011-09-15

    Highlights: > Dy/Tm co-doping method in BaTiO{sub 3} was suggested to improve electrical properties and temperature stability simultaneously. > We examined these properties in terms of microstructural analysis and substitution rate. > Increase of Dy{sub 2}O{sub 3} addition enhanced dielectric constant. > Increase of Tm{sub 2}O{sub 3} addition enhanced temperature stability. > Improved electrical properties and temperature stability through Dy/Tm co-doping were deduced from formation of electrons and core-shell structure. - Abstract: The co-doping characteristics on microstructure and thermal properties of barium titanate (BaTiO{sub 3}) were investigated to elucidate formation of core-shell structure by dysprosium (Dy) and thulium (Tm) addition in the BaTiO{sub 3}-Dy{sub 2}O{sub 3}-Tm{sub 2}O{sub 3} system. The dielectrics co-doped with 0.7 mol% Dy{sub 2}O{sub 3} and 0.3 mol% Tm{sub 2}O{sub 3} had the dielectric constant up to 2200 as a function of temperature, which was 30% higher than that of specimen containing only Tm{sub 2}O{sub 3} at the room temperature. It could be explained by the fact that the increase of Dy{sub 2}O{sub 3} addition contributed to the improvement of dielectric constant. On the other hand, the rapid diffusion rate of Dy{sup 3+} ions in BaTiO{sub 3} showed an adverse effect on temperature stability caused by destruction of core-shell. As the compensation for shell expansion in BaTiO{sub 3}, the reinforcement of the core-shell structure through the addition of Tm{sub 2}O{sub 3} was confirmed by TEM-EDS analysis and attributed the temperature coefficient of capacitance (TCC) in a reliability condition (-55 deg. C to 125 deg. C, {Delta}C = {+-}15% or less). The enhanced electrical properties and temperature stability could be deduced from the generation of electrons and the formation core-shell structure in co-doped BaTiO{sub 3} system respectively.

  10. Single-molecule magnet behavior in an octanuclear dysprosium(iii) aggregate inherited from helical triangular Dy3 SMM-building blocks.

    Science.gov (United States)

    Zhang, Li; Zhang, Peng; Zhao, Lang; Wu, Jianfeng; Guo, Mei; Tang, Jinkui

    2016-06-28

    An unprecedented octanuclear dysprosium(iii) cluster with the formula [Dy8L6(μ3-OH)4(μ2-CH3O)2(CH3OH)6(H2O)2]·6H2O·10CH3OH·2CH3CN () based on a nonlinearly tritopic aroylhydrazone ligand H3L has been isolated, realizing the successful linking of pairwise interesting triangular Dy3 SMMs. It is noteworthy that two enantiomers (Λ and Δ configurations) individually behaving as a coordination-induced chirality presented in the Dy3 helicate are connected in the meso Dy8 cluster. Remarkably, alternating-current magnetic susceptibility measurements revealed that the Dy8 cluster shows typical SMM behavior inherited from its Dy3 helical precursor. It is one of the rare polynuclear Lnn SMMs (n > 7) under zero dc field.

  11. Study for the determination of samarium, europium,terbium, dysprosium and yttrium in gadolinium oxide matrix by means of atomic absorption spectrophotometry using a graphite furnace

    International Nuclear Information System (INIS)

    Caires, A.C.F.

    1985-01-01

    A study for determination of samarium, europium, terbium, dysprosium and yttrium in a gadolinium oxide matrix by atomic absorption spectrophotometry using a graphite furnace is presented. The best charrring and atomization conditions were estabilished for each element, the most convenient ressonance lines being selected as well. The study was carried out for the mentioned lanthanides both when pure and when in binary mixtures with gadolinium, besides those where all for them were together with gadolinium. The determination limits for pure lanthanides were found to be between 1.3 and 9.6 ng assuming a 20% relative standard deviation as acceptable. The detection limits were in the range 0.51 and 7.5 ng, assuming as positive any answer higher than twofold the standard deviation. (author) [pt

  12. Synthesis and X-ray diffraction studies of dysprosium-calcium ferrites Dy1-xCaxFeO3-y (0≤x≤2/3)

    International Nuclear Information System (INIS)

    Li, J.; Song, D.; Su, Z.; Wang, T.M.

    1997-01-01

    Samples of dysprosium-calcium ferrites Dy 1-x Ca x FeO 3-y with x ranging from 0 to 2/3 were novelly prepared in air by solid state reaction and characterized by X-ray powder diffraction. These samples are single-phased orthorhombic perovskite-type compounds belonging to the space group D 2h 16 -Pbnm. The lattice constants of the Dy 1-x Ca x FeO 3-y samples have been refined by Cohen's least-squares method. The initial substitution of Ca for Dy leads to a decrease of the lattice constants. Further substitution of Ca for Dy has hardly any influence on the lattice dimensions. (orig.)

  13. 25 CFR 1000.162 - What is included in a self-governance compact?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false What is included in a self-governance compact? 1000.162...-DETERMINATION AND EDUCATION ACT Negotiation Process for Annual Funding Agreements Negotiating A Self-Governance Compact § 1000.162 What is included in a self-governance compact? A model format for self-governance...

  14. 33 CFR 162.175 - Black Rock Canal and Lock at Buffalo, New York.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Black Rock Canal and Lock at Buffalo, New York. 162.175 Section 162.175 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... Black Rock Canal and Lock at Buffalo, New York. In the Black Rock Canal and Lock, no vessel may exceed 6...

  15. 33 CFR 162.165 - Buffalo and Rochester Harbors, New York.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Buffalo and Rochester Harbors, New York. 162.165 Section 162.165 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... and Rochester Harbors, New York. In Buffalo and Rochester Harbors, no vessel may exceed 6 miles per...

  16. 29 CFR 1952.162 - Completion of developmental steps and certification.

    Science.gov (United States)

    2010-07-01

    ... occupational safety and health issues specified in the plan on or before July 20, 1976. (n) Amendment to....162 Section 1952.162 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH...) In accordance with the requirements of § 1952.163(b), the Iowa Occupational Safety and Health Act of...

  17. 25 CFR 162.229 - How long can the term of an agricultural lease run?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false How long can the term of an agricultural lease run? 162... AND PERMITS Agricultural Leases Lease Requirements § 162.229 How long can the term of an agricultural lease run? (a) An agricultural lease must provide for a definite lease term, specifying the commencement...

  18. 29 CFR 4.162 - Fringe benefits under contracts exceeding $2,500.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Fringe benefits under contracts exceeding $2,500. 4.162... Compensation Standards § 4.162 Fringe benefits under contracts exceeding $2,500. (a) Pursuant to the statutory... contain a provision specifying the fringe benefits to be furnished the various classes of service...

  19. 75 FR 27855 - Certifications Pursuant to Section 609 of Public Law 101-162

    Science.gov (United States)

    2010-05-18

    ... DEPARTMENT OF STATE [Public Notice 7013] Certifications Pursuant to Section 609 of Public Law 101... Law 101-162 (``Section 609''), that 13 nations have adopted programs to reduce the incidental capture... 609 of Public Law 101-162 prohibits imports of certain categories of shrimp unless the President...

  20. β-decay spectroscopy of neutron-rich 160,161,162Sm isotopes

    Directory of Open Access Journals (Sweden)

    Patel Z.

    2016-01-01

    Full Text Available Neutron-rich 160,161,162Sm isotopes have been populated at the RIBF, RIKEN via β first time. β-coincident γ rays were observed in all three isotopes including γ rays from the isomeric decay of 160Sm and 162Sm. The isomers in 160Sm and 162Sm have previously been observed but have been populated via β decay for the first time. The isomeric state in 162Sm is assigned a 4−v72+[ 633 ]⊗v12−[ 521 ]${4^ - }v{{7 \\over 2}^ + }\\left[ {633} \\right] \\otimes v{{1 \\over 2}^ - }\\left[ {521} \\right]$ configuration based on the decay pattern. The level schemes of 160Sm and 162Sm are presented. The ground states in the parent nuclei 160Pm and 162Pm are both assigned a 6−v72+[633]⊗π52−[532]${6^ - }v{{7 \\over 2}^ + }\\left[ {633} \\right] \\otimes \\pi {{5 \\over 2}^ - }\\left[ {532} \\right]$ configuration based on the population of states in the daughter nuclei. Blocked BCS calculations were performed to further investigate the spin-parities of the ground states in 160Pm, 161Pm, and 162Pm, and the isomeric state in 162Sm

  1. 19 CFR 162.93 - Failure to issue notice of seizure.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Failure to issue notice of seizure. 162.93 Section... OF THE TREASURY (CONTINUED) INSPECTION, SEARCH, AND SEIZURE Civil Asset Forfeiture Reform Act § 162.93 Failure to issue notice of seizure. If Customs does not send notice of a seizure of property in...

  2. 25 CFR 162.212 - When will the BIA advertise Indian land for agricultural leases?

    Science.gov (United States)

    2010-04-01

    ... laws and leasing policies that have been made applicable to the land under §§ 162.109 and 162.203 of..., unless a preference in favor of individual Indians is required by a superseding tribal law or leasing policy. (c) Advertisements will require sealed bids, and they may also provide for further competitive...

  3. Decay properties of nuclei close to Z = 108 and N = 162

    International Nuclear Information System (INIS)

    Dvorak, Jan

    2007-01-01

    The goal of the research conducted in the frame of this thesis was to investigate the decay properties of the nuclides 269-271 Hs and their daughters using an improved chemical separation and detection system. Shell stabilization was predicted in the region around Z=108 and N=162 in calculations, taking into account possible higher orders of deformations of the nuclei. The nucleus 270 Hs with a closed proton and a closed neutron deformed shell, was predicted to be ''deformed doubly magic''. Nuclei around 270 Hs can be produced only via fusion reactions at picobarn levels, resulting in a production rates of few atoms per day. Investigating short-lived nuclei using rapid chemical separation and subsequent on-line detection methods provides an independent and alternative means to electromagnetic on-line separators. Chemical separation of Hs in the form of HsO 4 provides an excellent tool to study the formation reactions and nuclear structure in this region of the chart of nuclides due to a high overall efficiency and a very high purification factor. The goal was accomplished, as element 108, hassium, was produced in the reaction 248 Cm( 26 Mg,xn) 274-x Hs and chemically isolated. After gas phase separation of HsO 4 , 26 genetically linked decay chains have been observed. These were attributed to decays of three different Hs isotopes produced in the 3-5n evaporation channels. The known decay chain of 269 Hs, the 5n evaporation product, serves as an anchor point, thus allowing the unambiguous assignment of the observed decay chains to the 5n, 4n, and 3n channels, respectively. Decay properties of five nuclei have been unambiguously established for the first time, including the one for the the doubly-magic nuclide 270 Hs. This hassium isotope is the next doubly magic nucleus after the well known 208 Pb and the first experimentally observed even-even nucleus on the predicted N=162 neutron shell. The observed decay properties provide strong indications for enhanced nuclear

  4. Epidemiology and mortality of 162 major burns in Kuwait.

    Science.gov (United States)

    Bang, R L; Ghoneim, I E

    1996-09-01

    The burns intensive care unit at IBN Sina Hospital reopened in July 1991, following the Iraqi occupation of Kuwait and the Gulf War. Epidemiology and mortality of 162 burn patients with 30 per cent and over total body surface area (TBSA) burns, treated from July 1991 to December 1994, is presented. There were 91 males and 71 females with a ratio of 1.3 to 1. The median age was 30 years (range 4 months to 93 years) and 44 per cent of the patients were 15-40 years of age. 124 (76.5 per cent) accidents occurred at home and the flame burn was the commonest involving 131 (80.9 per cent) patients. The median burn surface area was 45.5 per cent and the majority of them sustained deep burns. The hospital stay of the surviving patients ranged from 11 to 174 days (median 38 days), while the day of the death was from 1 to 134 days. Forty-six deaths represent an overall mortality rate of 28.4 per cent amongst our patients. All the patients whose Baux score was 130 and above died. Burn shock was responsible for 10 deaths, and out of them eight were not actively resuscitated due to high Baux score. Sixteen deaths occurred within 48 h postburn. Septicaemia and its related effects were responsible for the majority of the deaths.

  5. Observation of enhanced nuclear stability near the 162 neutron shell

    Energy Technology Data Exchange (ETDEWEB)

    Lougheed, R.W.; Moody, K.J.; Wild, J.F.; Hulet, E.K.; McQuaid, J.H. [Lawrence Livermore National Lab., CA (United States); Lazarev, Yu.A.; Lobanov, Yu.V.; Oganessian, Yu.Ts.; Utyonkov, V.K.; Abdullin, F.Sh.; Buklanov, G.V.; Gikal, B.N.; Iliev, S.; Mezentsev, A.N.; Polyakov, A.N.; Sedykh, I.M.; Shirokovsky, I.V.; Subbotin, V.G.; Sukhov, A.M.; Tsyganov, Yu.S.; Zhuchko, V.E. [Joint Inst. for Nuclear Research, Dubna (Russian Federation)

    1993-09-22

    In bombardments of {sup 248}Cm with {sup 22}Ne the authors discovered two new isotopes, {sup 265}106 and {sup 266}106, by establishing genetic links between {alpha} decays of the 106 nuclides and SF or {alpha} decays of the daughter (grand-daughter) nuclides. For {sup 266}106 they measured E{sub {alpha}}=8.62{+-}0.06 MeV followed by the SF decay of {sup 262}104 for which they measured a half-life value of 1.2{sup +1.0}{sub {minus}0.5} s. For {sup 265}106 they measured E{sub {alpha}}=8.82{+-}0.06 MeV. They estimated {alpha} half-lives of 10-30 s for {sup 266}106 and 2-30 s for {sup 265}106 with SF branches of {approximately}50% or less. The decay properties of {sup 266}106 indicate a large enhancement in the SF stability of this N=160 nuclide and confirm the existence of the predicted neutron-deformed shell N=162.

  6. Three band crossings in the yrast structure of 162Hf

    International Nuclear Information System (INIS)

    Bingham, C.R.; Riedinger, L.L.; Courtney, L.H.

    1988-01-01

    The yrast sequence of 162 Hf has been observed up to a level tentatively assigned as 38 + and reveals a continuing rotational character up to that spin. Sharp backbends at rotational frequencies of 0.27 and 0.42 MeV/ℎ are attributed to isub(13/2) neutron and hsub(11/2) proton alignments, respectively. A gradual increase in the aligned angular momentum of the yrast levels between these two sharp backbends is attributed to the rotational alignment of a pair of negative parity quasineutrons (mostly hsub(9/2) in character). The interpretation of this effect is supported by the failure of the negative parity bands, which already contain this aligned hsub(9/2) neutron, to gain alignment in the same rotational frequency range. While the alignment of the hsub(9/2) quasineutrons has been predicted in the cranked shell model to occur in the rare-earth region with a large interaction strength, this represents the first clear observation of such a band crossing. (author)

  7. Time-resolved photodissociation of oxygen at 162 nm

    International Nuclear Information System (INIS)

    Trushin, Sergei A; Schmid, Wolfram E; Fuss, Werner

    2011-01-01

    Oxygen was excited by 10 fs pulses in the Schumann-Runge continuum at 162 nm, which is by 0.57 eV above the dissociation limit. It was probed by high-intensity ionization at 810 nm with 10 14 W cm -2 , measuring the ion yields. The O 2 + signal decays in 4.3 fs, which is much shorter than the expected time for dissociation. It is ascribed to a rapid decay of the ionization probability. In a similar time, the ion in the second excited state (with excess energy taken over from the neutral) reaches the dissociation limit, whereas this time would be much longer from the two lower ion states. In fact, the O + signal rises to a (first) maximum at 6 fs. The preference for the higher ion state is rationalized by an intermediate resonance in the neutral molecule for which the polarization dependence also provides evidence. But the shape of the O + signal is very odd: it exhibits three maxima (at 6, 29 and 53 fs) of increasing intensity, before decaying rapidly (≤3.5 fs) to a pedestal. In contrast to the first maximum, the others appear at times when there is practically no interatomic force left in the excited state. We postulate a highly repulsive doubly excited state as a resonance for interpreting the second maximum, and for the third an ion-pair state lying further outside. Comparison is made with enhanced ionization, which has often been found at large interatomic distances on multiple ionization in strong laser fields. Consistent with this mechanism is the absence of similar observations at negative delay times, where five fundamental photons act as a pump and the fifth harmonic as a probe.

  8. First observation of yrast band in odd-odd 162Lu

    International Nuclear Information System (INIS)

    Zhang, Y.H.; Yuan, G.J.; Liu, X.A.

    1996-01-01

    High spin states of the odd-odd 162 Lu nucleus have been studied via 147 Sm( 19 F, 4nγ) 162 Lu reaction at 95MeV beam energy. Level scheme for yrast band based on π[h 11/2 ] υ[i 13/2 ] quasiparticle configuration was established up to I π =(23 - ) for the first time. This band shows the signature inversion in energy before backbending generally appeared in this mass region. It is stressed that the signature splitting in 162 Lu is larger than that in the 160 Tm nucleus. (orig.)

  9. A study of the structure of 162Dy through the (n,γ) and (n,e-) reactions

    International Nuclear Information System (INIS)

    Warner, D.D.; Shi, Z.R.; Gelletly, W.; Borner, H.G.; Hoyler, F.; Schreckenbach, K.; van Isacker, P.

    1987-01-01

    The level structure below 2 MeV in 162 Dy has been investigated using the 161 Dy(n,γ) 162 Dy and 161 Dy(n,e - ) 162 Dy reactions. The results for the positive parity excitations are discussed within the framework of an Interacting Boson Approximation (IBA-2) calculation. 7 refs., 1 fig., 1 tab

  10. 33 CFR 162.20 - Flushing Bay near La Guardia Airport, Flushing, N.Y.; restricted area.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Flushing Bay near La Guardia Airport, Flushing, N.Y.; restricted area. 162.20 Section 162.20 Navigation and Navigable Waters COAST... NAVIGATION REGULATIONS § 162.20 Flushing Bay near La Guardia Airport, Flushing, N.Y.; restricted area. (a...

  11. 33 CFR 162.260 - Channel leading to San Juan Harbor, P.R.; use, administration, and navigation.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Channel leading to San Juan Harbor, P.R.; use, administration, and navigation. 162.260 Section 162.260 Navigation and Navigable... WATERWAYS NAVIGATION REGULATIONS § 162.260 Channel leading to San Juan Harbor, P.R.; use, administration...

  12. Influence of intramolecular f-f interactions on nuclear spin driven quantum tunneling of magnetizations in quadruple-decker phthalocyanine complexes containing two terbium or dysprosium magnetic centers.

    Science.gov (United States)

    Fukuda, Takamitsu; Matsumura, Kazuya; Ishikawa, Naoto

    2013-10-10

    Nuclear spin driven quantum tunneling of magnetization (QTM) phenomena, which arise from admixture of more than two orthogonal electronic spin wave functions through the couplings with those of the nuclear spins, are one of the important magnetic relaxation processes in lanthanide single molecule magnets (SMMs) in the low temperature range. Although recent experimental studies have indicated that the presence of the intramolecular f-f interactions affects their magnetic relaxation processes, little attention has been given to their mechanisms and, to the best of our knowledge, no rational theoretical models have been proposed for the interpretations of how the nuclear spin driven QTMs are influenced by the f-f interactions. Since quadruple-decker phthalocyanine complexes with two terbium or dysprosium ions as the magnetic centers show moderate f-f interactions, these are appropriate to investigate the influence of the f-f interactions on the dynamic magnetic relaxation processes. In the present paper, a theoretical model including ligand field (LF) potentials, hyperfine, nuclear quadrupole, magnetic dipolar, and the Zeeman interactions has been constructed to understand the roles of the nuclear spins for the QTM processes, and the resultant Zeeman plots are obtained. The ac susceptibility measurements of the magnetically diluted quadruple-decker monoterbium and diterbium phthalocyanine complexes, [Tb-Y] and [Tb-Tb], have indicated that the presence of the f-f interactions suppresses the QTMs in the absence of the external magnetic field (H(dc)) being consistent with previous reports. On the contrary, the faster magnetic relaxation processes are observed for [Tb-Tb] than [Tb-Y] at H(dc) = 1000 Oe, clearly demonstrating that the QTMs are rather enhanced in the presence of the external magnetic field. Based on the calculated Zeeman diagrams, these observations can be attributed to the enhanced nuclear spin driven QTMs for [Tb-Tb]. At the H(dc) higher than 2000 Oe, the

  13. Dual-mode T_1 and T_2 magnetic resonance imaging contrast agent based on ultrasmall mixed gadolinium-dysprosium oxide nanoparticles: synthesis, characterization, and in vivo application

    International Nuclear Information System (INIS)

    Tegafaw, Tirusew; Xu, Wenlong; Ahmad, Md Wasi; Lee, Gang Ho; Baeck, Jong Su; Chang, Yongmin; Bae, Ji Eun; Chae, Kwon Seok; Kim, Tae Jeong

    2015-01-01

    A new type of dual-mode T_1 and T_2 magnetic resonance imaging (MRI) contrast agent based on mixed lanthanide oxide nanoparticles was synthesized. Gd"3"+ ("8S_7_/_2) plays an important role in T_1 MRI contrast agents because of its large electron spin magnetic moment resulting from its seven unpaired 4f-electrons, and Dy"3"+ ("6H_1_5_/_2) has the potential to be used in T_2 MRI contrast agents because of its very large total electron magnetic moment: among lanthanide oxide nanoparticles, Dy_2O_3 nanoparticles have the largest magnetic moments at room temperature. Using these properties of Gd"3"+ and Dy"3"+ and their oxide nanoparticles, ultrasmall mixed gadolinium-dysprosium oxide (GDO) nanoparticles were synthesized and their potential to act as a dual-mode T_1 and T_2 MRI contrast agent was investigated in vitro and in vivo. The D-glucuronic acid coated GDO nanoparticles (d_a_v_g = 1.0 nm) showed large r_1 and r_2 values (r_2/r_1 ≈ 6.6) and as a result clear dose-dependent contrast enhancements in R_1 and R_2 map images. Finally, the dual-mode imaging capability of the nanoparticles was confirmed by obtaining in vivo T_1 and T_2 MR images. (paper)

  14. Extraction of Dysprosium Ions with DTPA Functionalized Superparamagnetic Nanoparticles Probed by Energy Dispersive X-ray Fluorescence and TEM/High-Angle Annular Dark Field Imaging.

    Science.gov (United States)

    Melo, Fernando Menegatti de; Almeida, Sabrina da Nobrega; Uezu, Noemi Saori; Ramirez, Carlos Alberto Ospina; Santos, Antonio Domingues Dos; Toma, Henrique Eisi

    2018-06-01

    The extraction of dysprosium (Dy3+) ions from aqueous solution was carried out successfully, using magnetite (Fe3O4) nanoparticles functionalized with diethylenetriaminepentaacetic acid (MagNP@DTPA). The process was monitored by energy dispersive X-ray fluorescence spectroscopy, as a function of concentration, proceeding according to a Langmuir isotherm with an equilibrium constant of 2.57 × 10-3 g(MagNP) L-1 and a saturation limit of 63.2 mgDy/gMagNP. The presence of paramagnetic Dy3+ ions attached to the superparamagnetic nanoparticles led to an overall decrease of magnetization. By imaging the nanoparticles surface using scanning transmission electron microscopy equipped with high resolution elemental analysis, it was possible to probe the binding of the Dy3+ ions to DTPA, and to show their distribution in a region of negative magnetic field gradients. This finding is coherent with the observed decrease of magnetization, associated with the antiferromagnetic coupling between the lanthanide ions and the Fe3O4 core.

  15. Psoriatic arthritis: A retrospective study of 162 patients

    Directory of Open Access Journals (Sweden)

    Pavlica Ljiljana

    2005-01-01

    Full Text Available Aim. The aim of our study was to determine the prevalence of psoriatic arthritis in the patients with psoriasis and to analyze retrospectively the results of a 34-year multidisciplinary management of the patients with psoriatic arthritis. Methods. The study included 162 out of 183 treated patients with psoriatic arthritis, aged 48 ± 15 years. All the patients satisfied the current diagnostic criteria for psoriasis and psoriatic arthritis according to the American College of Rheumatology. Results. Psoriatic arthritis developed in 183 (9.3% out of 1976 patients with psoriasis. Time interval for establishing the diagnosis was 4 years. A positive family history of the disease had 15.0% of the studied patients. Its onset was most often at 42 years of age in 70.4% of the cases, and 2 months to 59 years after the appearance of psoriasis. Psoriatic arthritis without psoriasis appeared in 1.8% of the patients. A severe form of arthritis had 64.2% of the patients, mainly the patients with scalp psoriasis (χ2=3.2; p<0.05. Nail changes had 35% of the patients. Distal interphalangeal joints were involved in 63.6%, axial skeleton in 36.4%, oligoarthritis in 45.0%, polyarthritis in 55.0%, and mutilating form in 6.8% of the patients. Elevated Erythrocyte Sedimentation Rate was reveald in 61.7% of the patients. Immunoglobulin M (IgM rheumatoid factor was altered in 4.3% of the patients. The human leukocyte antigen (HLA typing in the 28 patients were: A2 32.0%, A3 18.0%, Al and A9 14.0%, A28 and A29 3.5%, B8 and B16 14.0%, B5 and B12 11.0%, B13,B15, B18, B27 and B35 7.0%. Radiologic changes were most often in hand and foot joints, less frequently in the knees and quite infrequently in hips and shoulders joints. Sacroiliitis was found in 46.4% of the patients. Psoriasis was treated with topical corticosteroids and salicylic ointments in all the patients, ultraviolet (PUVA therapy in 5.6% and retinoids in 4.3% of them. Artrithis was treated with nonsteroidal anti

  16. Decay properties of nuclei close to Z = 108 and N = 162

    Energy Technology Data Exchange (ETDEWEB)

    Dvorak, Jan

    2007-07-12

    The goal of the research conducted in the frame of this thesis was to investigate the decay properties of the nuclides {sup 269-271}Hs and their daughters using an improved chemical separation and detection system. Shell stabilization was predicted in the region around Z=108 and N=162 in calculations, taking into account possible higher orders of deformations of the nuclei. The nucleus {sup 270}Hs with a closed proton and a closed neutron deformed shell, was predicted to be ''deformed doubly magic''. Nuclei around {sup 270}Hs can be produced only via fusion reactions at picobarn levels, resulting in a production rates of few atoms per day. Investigating short-lived nuclei using rapid chemical separation and subsequent on-line detection methods provides an independent and alternative means to electromagnetic on-line separators. Chemical separation of Hs in the form of HsO{sub 4} provides an excellent tool to study the formation reactions and nuclear structure in this region of the chart of nuclides due to a high overall efficiency and a very high purification factor. The goal was accomplished, as element 108, hassium, was produced in the reaction {sup 248}Cm({sup 26}Mg,xn){sup 274-x}Hs and chemically isolated. After gas phase separation of HsO{sub 4}, 26 genetically linked decay chains have been observed. These were attributed to decays of three different Hs isotopes produced in the 3-5n evaporation channels. The known decay chain of {sup 269}Hs, the 5n evaporation product, serves as an anchor point, thus allowing the unambiguous assignment of the observed decay chains to the 5n, 4n, and 3n channels, respectively. Decay properties of five nuclei have been unambiguously established for the first time, including the one for the the doubly-magic nuclide {sup 270}Hs. This hassium isotope is the next doubly magic nucleus after the well known {sup 208}Pb and the first experimentally observed even-even nucleus on the predicted N=162 neutron shell. The

  17. Global use structures of the magnetic materials neodymium and dysprosium. A scenario-based analysis of the effect of the diffusion of electromobility on the demand for rare earths; Globale Verwendungsstrukturen der Magnetwerkstoffe Neodym und Dysprosium. Eine szenariobasierte Analyse der Auswirkung der Diffusion der Elektromobilitaet auf den Bedarf an Seltenen Erden

    Energy Technology Data Exchange (ETDEWEB)

    Gloeser-Chahoud, Simon; Kuehn, Andre; Tercero Espinoza, Luis

    2016-06-15

    Neodymium-iron-boron magnets (NdFeB) have experienced a significant demand as the most powerful permanent magnet in recent years, especially for the manufacture of compact electric servomotors with high efficiency and high power density, especially for mobile applications in hybrid traction motors and electric vehicles or for electric bikes. However, NdFeB magnets are also increasingly being used in general mechanical engineering (conveying and pumping systems, tools, air conditioning systems, lift motors, etc.), in the small electric motors of conventional passenger cars or in the generators of large wind power plants with permanent magnetic direct drive. Nevertheless, there is still high uncertainty in the use structures of NdFeB magnets and the contained rare earth elements neodymium and dysprosium. An effective instrument for increasing the market transparency and the understanding of complex anthropogenic material cycles is the dynamic material flow modeling. In the present work paper, this instrument is used for an in-depth analysis of the use structures of NdFeB magnets and the contained rare earths on a global scale. The dynamic modeling of product usage cycles reveals today's usage structures and quantifies future magnetic quantities in obsolete product flows. It could be shown that the magnets in today's scrap volume are mainly contained in obsolete electronics applications such as hard disks (HDD), CD and DVD drives, which makes the recycling hardly seem to be economical due to the small magnets and the high material spread, but in the foreseeable future with larger magnetic quantities from synchronous servomotors and generators can be expected, which significantly increases the recycling potential. In a further step, the effect of the diffusion of alternative drives in the automotive market on the dysprosium requirement is analyzed using a system dynamics model and possible adaptation mechanisms in the form of different substitution effects in

  18. 25 CFR 162.101 - What key terms do I need to know?

    Science.gov (United States)

    2010-04-01

    ... Agricultural Resources Management Act of December 3, 1993 (107 Stat. 2011, 25 U.S.C. 3701 et seq.), as amended... tribe acting on behalf of BIA under § 162.109 of this part. Bond means security for the performance of... uncertain in duration, including a life estate. Lease means a written agreement between Indian landowners...

  19. 33 CFR 162.225 - Columbia and Willamette Rivers, Washington and Oregon; administration and navigation.

    Science.gov (United States)

    2010-07-01

    ... the river as appropriate such temporary speed regulations as he may deem necessary to protect the... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Columbia and Willamette Rivers... NAVIGATION REGULATIONS § 162.225 Columbia and Willamette Rivers, Washington and Oregon; administration and...

  20. 26 CFR 1.162-14 - Expenditures for advertising or promotion of good will.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Expenditures for advertising or promotion of... and Corporations § 1.162-14 Expenditures for advertising or promotion of good will. A corporation... expenditures for advertising or the promotion of good will which it seeks to deduct in the taxable year may not...

  1. Measurements of np scattering at 96 and 162 MeV

    International Nuclear Information System (INIS)

    Olsson, N.; Rahm, J.; Blomgren, J.; Conde, H.; Dangtip, S.; Elmgren, K.; Roennqvist, T.; Zorro, R.; Ringbom, A.; Tibell, G.

    1998-01-01

    This paper presents new, precise measurements of differential cross sections for np scattering at 96 and 162 MeV. The data are steeper at backward angles than most previous data, and point to the classical value for the charged πNN coupling constant. (orig.)

  2. 46 CFR 162.050-20 - Separator and bilge alarm test fluids.

    Science.gov (United States)

    2010-10-01

    ... residual fuel oil in accordance with ISO 8217 (incorporated by reference, see § 162.050-4), type RMG 380... water; (ii) 25.0 g of Test Fluid A; (iii) 25.0 g of Test Fluid B; (iv) 0.5 g of surfactant (sodium salt...

  3. 19 CFR 162.66 - Penalties for unlading narcotic drugs or marihuana without a permit.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Penalties for unlading narcotic drugs or marihuana... Substances, Narcotics, and Marihuana § 162.66 Penalties for unlading narcotic drugs or marihuana without a permit. In every case where a narcotic drug or marihuana is unladen without a permit, the penalties...

  4. 26 CFR 1.162-22 - Treble damage payments under the antitrust laws.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Treble damage payments under the antitrust laws... Corporations § 1.162-22 Treble damage payments under the antitrust laws. (a) In general. In the case of a... Federal antitrust laws or enters a plea of guilty or nolo contendere to an indictment or information...

  5. 19 CFR 162.96 - Remission of forfeitures and payment of fees, costs or interest.

    Science.gov (United States)

    2010-04-01

    ... Asset Forfeiture Reform Act § 162.96 Remission of forfeitures and payment of fees, costs or interest... for purposes of collection of any fees, costs or interest from the Government. ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Remission of forfeitures and payment of fees...

  6. RAF V Sweatman (162/2014) [2015] ZASCA 22 (20 march 2015) A ...

    African Journals Online (AJOL)

    RAF V Sweatman (162/2014) [2015] ZASCA 22 (20 march 2015) A simple illustration of the SCA's statutory ... Log in or Register to get access to full text downloads. ... The effect is that one of the primary purposes of the Amendment Act is ...

  7. 45 CFR 162.1902 - Standard for Medicaid pharmacy subrogation transaction.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Standard for Medicaid pharmacy subrogation... DATA STANDARDS AND RELATED REQUIREMENTS ADMINISTRATIVE REQUIREMENTS Medicaid Pharmacy Subrogation § 162.1902 Standard for Medicaid pharmacy subrogation transaction. The Secretary adopts the Batch Standard...

  8. 26 CFR 1.162-25T - Deductions with respect to noncash fringe benefits (temporary).

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Deductions with respect to noncash fringe... Individuals and Corporations § 1.162-25T Deductions with respect to noncash fringe benefits (temporary). (a) Employer. If an employer includes the value of a noncash fringe benefit in an employee's gross income, the...

  9. 26 CFR 1.162-25 - Deductions with respect to noncash fringe benefits.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Deductions with respect to noncash fringe... Corporations § 1.162-25 Deductions with respect to noncash fringe benefits. (a) [Reserved] (b) Employee. If an employer provides the use of a vehicle (as defined in § 1.61-21(e)(2)) to an employee as a noncash fringe...

  10. 47 CFR 1.62 - Operation pending action on renewal application.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Operation pending action on renewal application... General Rules of Practice and Procedure General Application Procedures § 1.62 Operation pending action on renewal application. (a)(1) Where there is pending before the Commission at the time of expiration of...

  11. 40 CFR 81.162 - Northeast Plateau Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Plateau Intrastate Air... Air Quality Control Regions § 81.162 Northeast Plateau Intrastate Air Quality Control Region. The Northeast Plateau Intrastate Air Quality Control Region (California) consists of the territorial area...

  12. 26 CFR 1.162-17 - Reporting and substantiation of certain business expenses of employees.

    Science.gov (United States)

    2010-04-01

    ... Individuals and Corporations § 1.162-17 Reporting and substantiation of certain business expenses of employees.... The term “ordinary and necessary business expenses” means only those expenses which are ordinary and..., reimbursements, or otherwise, exceeds the ordinary and necessary business expenses paid or incurred by the...

  13. 33 CFR 162.85 - Yazoo Diversion Canal, Vicksburg, Miss., from its mouth at Kleinston Landing to Fisher Street...

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Yazoo Diversion Canal, Vicksburg, Miss., from its mouth at Kleinston Landing to Fisher Street; navigation. 162.85 Section 162.85... mouth at Kleinston Landing to Fisher Street; navigation. (a) Speed. Excessive speeding is prohibited. A...

  14. 25 CFR 162.201 - Must agricultural land be managed in accordance with a tribe's agricultural resource management...

    Science.gov (United States)

    2010-04-01

    ... identify holistic management objectives; and (5) Identify actions to be taken to reach established... tribe's agricultural resource management plan? 162.201 Section 162.201 Indians BUREAU OF INDIAN AFFAIRS... Must agricultural land be managed in accordance with a tribe's agricultural resource management plan...

  15. 40 CFR 429.162 - Effluent limitations representing the degree of effluent reduction attainable by the application...

    Science.gov (United States)

    2010-07-01

    ... technology (BCT). [Reserved] 429.162 Section 429.162 Protection of Environment ENVIRONMENTAL PROTECTION... Wood Furniture and Fixture Production Without Water Wash Spray Booth(s) or Without Laundry Facilities... application of the best conventional pollutant control technology (BCT). [Reserved] ...

  16. 27 CFR 1.62 - Use of distilled spirits or wine for experimental purposes and in manufacture of nonbeverage...

    Science.gov (United States)

    2010-04-01

    ... or wine for experimental purposes and in manufacture of nonbeverage products. 1.62 Section 1.62... experimental purposes and in manufacture of nonbeverage products. The use of distilled spirits or wine for experimental purposes and in the manufacture of (a) medicinal, pharmaceutical, or antiseptic products...

  17. Synthesis and characterization of a family of structurally characterized dysprosium alkoxides for improved fatigue-resistance characteristics of PDyZT thin films.

    Science.gov (United States)

    Boyle, Timothy J; Bunge, Scott D; Clem, Paul G; Richardson, Jacob; Dawley, Jeffrey T; Ottley, Leigh Anna M; Rodriguez, Mark A; Tuttle, Bruce A; Avilucea, Gabriel R; Tissot, Ralph G

    2005-03-07

    Using either an ammoniacal route, the reaction between DyCl3, Na0, and HOR in liquid ammonia, or preferentially reacting Dy(N(SiMe3)2)3 with HOR in a solvent, we isolated a family of dysprosium alkoxides as [Dy(mu-ONep)2(ONep)]4 (1), (ONep)2Dy[(mu3-ONep)(mu-ONep)Dy(ONep)(THF)]2(mu-ONep) (2), (ONep)2Dy[(mu3-ONep)(mu-ONep)Dy(ONep)(py)]2(mu-ONep) (3), [Dy3(mu3-OBut)2(mu-OBut3(OBut)4(HOBut)2] (4), [Dy3(mu3-OBut)2(mu-OBut)3(OBut)4(THF)2] (5), [Dy3(mu3-OBut)2(mu-OBut)3(OBut)4(py)2] (6), (DMP)Dy(mu-DMP)4[Dy(DMP)2(NH3)]2 (7), [Dy(eta6-DMP)(DMP)2]2 (8), Dy(DMP)3(THF)3 (9), Dy(DMP)3(py)3 (10), Dy(DIP)3(NH3)2 (11), [Dy(eta6-DIP)(DIP)2]2 (12), Dy(DIP)3(THF)2 (13), Dy(DIP)3(py)3 (14), Dy(DBP)3(NH3) (15), Dy(DBP)3 (16), Dy(DBP)3(THF) (17), Dy(DBP)3(py)2 (18), [Dy(mu-TPS)(TPS2]2 (19), Dy(TPS)3(THF)3 (20), and Dy(TPS)3(py)3 (21), where ONep = OCH2CMe3, OBut) = OCMe3, DMP = OC6H3(Me)(2)-2,6, DIP = OC6H3(CHMe2)(2)-2,6, DBP = OC6H3(CMe3)(2)-2,6, TPS = OSi(C6H5)3, tol = toluene, THF = tetrahydrofuran, and py = pyridine. We were not able to obtain X-ray quality crystals of compounds 2, 8, and 9. The structures observed and data collected for the Dy compounds are consistent with those reported for its other congeners. A number of these precursors were used as Dy dopants in Pb(Zr0.3Ti0.7)O3 (PZT 30/70) thin films, with compound 12 yielding the highest-quality films. The resulting Pb0.94Dy0.04(Zr0.3Ti0.7)O3 [PDyZT (4/30/70)] had similar properties to PZT (30/70), but showed substantial resistance to polarization reversal fatigue.

  18. The role of dysprosium on the structural and magnetic properties of (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles

    International Nuclear Information System (INIS)

    Rahimi, Hamed; Ghasemi, Ali; Mozaffarinia, Reza; Tavoosi, Majid

    2017-01-01

    In current work, Nd2Fe14B nanoparticles was synthesized by sol-gel method. Dysprosium powders were added into Nd2Fe14B nanoparticles by mechanical alloying process in order to enhancement of coercivity. The phase analysis, structure, and magnetic properties of annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles with different Dy-content (x=0.1, 0.2, 0.3, 0.4, 0.5, 0.6) were investigated by employing X-ray diffraction, X-ray photoelectron spectroscopy, energy dispersive spectroscopy, field emission scanning electron microscope, transmission electron microscope and vibrating sample magnetometer techniques. The results showed that with an increase in Dy amounts, the coercivity of particles increased from 2.9 kOe to 13.4 kOe and then decreased to 5.6 kOe. By adding an optimum amount of Dy (x=0.4), the coercivity was significantly increased from 2.9 kOe to 13.4 kOe. The average particle size of annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles was below 10 nm. Magnetization reversal studies indicate that the coercivity of milled and annealed (Nd_1_−_xDy_x)_2Fe_1_4B nanoparticles is controlled by the nucleation of reversed magnetic domains. The experimental results in the angular dependence of coercivity for (Nd_1_−_xDy_x)_2Fe_1_4B permanent magnets showed that the normalized coercivity of the permanent magnets H_c(θ)/H_c(0) increases from 1 to about 1.2–1.5 with increasing θ from 0 to about π/3, for x=0.4–0.6. - Highlights: • Dy was added to Nd_2Fe_1_4B nanoparticles to improve the coercivity. • A maximum squareness ratio of 0.99 was obtained. • The average particle size decreased with an increase in Dy-content.

  19. Global use structures of the magnetic materials neodymium and dysprosium. A scenario-based analysis of the effect of the diffusion of electromobility on the demand for rare earths

    International Nuclear Information System (INIS)

    Gloeser-Chahoud, Simon; Kuehn, Andre; Tercero Espinoza, Luis

    2016-01-01

    Neodymium-iron-boron magnets (NdFeB) have experienced a significant demand as the most powerful permanent magnet in recent years, especially for the manufacture of compact electric servomotors with high efficiency and high power density, especially for mobile applications in hybrid traction motors and electric vehicles or for electric bikes. However, NdFeB magnets are also increasingly being used in general mechanical engineering (conveying and pumping systems, tools, air conditioning systems, lift motors, etc.), in the small electric motors of conventional passenger cars or in the generators of large wind power plants with permanent magnetic direct drive. Nevertheless, there is still high uncertainty in the use structures of NdFeB magnets and the contained rare earth elements neodymium and dysprosium. An effective instrument for increasing the market transparency and the understanding of complex anthropogenic material cycles is the dynamic material flow modeling. In the present work paper, this instrument is used for an in-depth analysis of the use structures of NdFeB magnets and the contained rare earths on a global scale. The dynamic modeling of product usage cycles reveals today's usage structures and quantifies future magnetic quantities in obsolete product flows. It could be shown that the magnets in today's scrap volume are mainly contained in obsolete electronics applications such as hard disks (HDD), CD and DVD drives, which makes the recycling hardly seem to be economical due to the small magnets and the high material spread, but in the foreseeable future with larger magnetic quantities from synchronous servomotors and generators can be expected, which significantly increases the recycling potential. In a further step, the effect of the diffusion of alternative drives in the automotive market on the dysprosium requirement is analyzed using a system dynamics model and possible adaptation mechanisms in the form of different substitution effects in the

  20. The unpaired spectroscopy of sup 161,162 Er at spins up to 50 Dirac h

    Energy Technology Data Exchange (ETDEWEB)

    Riley, M.A.; Roberts, J.W.; Alderson, A.; Ali, I.; Cullen, D.M.; Fallon, P.; Forsyth, P.D.; Sharpey-Schafer, J.F. (Liverpool Univ. (UK). Oliver Lodge Lab.); Simpson, J.; Bentley, M.A.; Bruce, A.M. (Science and Engineering Research Council, Daresbury (UK). Daresbury Lab.); Chapman, R.; Lisle, J.C.; Mo, J.N. (Manchester Univ. (UK). Schuster Lab.)

    1990-12-24

    High spin states in {sup 161}Er and {sup 162}Er have been populated using the {sup 130}Te+{sup 36}S reaction at a bombarding energy of 170 MeV. In {sup 161}Er, three rotational bands were extended from I {approx equal} 35{Dirac h} to I {approx equal} 50{Dirac h}. In {sup 162}Er the positive parity yrast band was observed to I=44{Dirac h}. These rotational sequences are compared to a simple unpaired model which was successful in predicting the behaviour of similar high spin data on {sup 159,160}Er. These studies of the light Er isotopes constitute the highest spins observed in normal deformed nuclei and yield direct and specific information on the single-neutron spectrum of states. (orig.).

  1. Identification of 162Gd and a new type of identical bands

    International Nuclear Information System (INIS)

    Jones, E. F.; Gore, P. M.; Hamilton, J. H.; Ramayya, A. V.; Dodder, R. S.; Beyer, C. J.; Hwang, J. K.; Zhang, X. Q.; Kormicki, J.; Zhu, S. J.; Lima, A. P. de; Cole, J. D.; Aryaeinejad, R.; Ma, W. C.; Ter-Akopian, G. M.; Daniel, A. V.; Oganessian, Yu. Ts.; Rasmussen, J. O.; Asztalos, S. J.; Lee, I. Y.

    1998-01-01

    From γ-γ-γ coincidence measurements in spontaneous fission of 252 Cf, level energies were established to spins 14 + to 20 + in many neutron-rich nuclei. New isotope 162 Gd was identified. Yrast bands of 152,154,156 Nd, 156,158,160 Sm, and 160,162 Gd exhibit near-identical transition energies and moments of inertia (MOI) shifted by the same constant amounts for every spin state from 2 + to 12 + or 14 + for nuclei differing by 2n, 4n, 2p, 4p, α, α+2p, and α+2n. These shifted identical bands (SIB) are a new phenomenon. Analysis of all known even-even proton- to neutron-rich nuclei from Ba(Z=56) to Os(Z=76) reveal no SIB for proton-rich nuclei and few cases of SIB for the most neutron-rich pairs around N=98-102 separated by 2n and 2p

  2. Microscopic analysis of wobbling excitations in 156Dy and 162Yb

    International Nuclear Information System (INIS)

    Nazmitdinov, R. G.; Kvasil, J.

    2007-01-01

    In the cranked Nilsson-plus-random-phase approximation, we study low-lying quadrupole excitations of positive parity and negative signature in 156 Dy and 162 Yb at high spins. Special attention is paid to a consistent description of wobbling excitations and their identification among excited states. A good agreement between the available experimental data and the results of calculations is obtained. We find that the lowest odd-spin γ-vibrational states in 156 Dy transform into wobbling excitations after the backbending associated with the transition from an axially symmetric shape to a nonaxial shape. Similar results are predicted for 162 Yb. The analysis of electromagnetic transitions uniquely determines the sign of the γ deformation in both nuclei after the transition point

  3. Yrast bands and signature inversion in double odd 162,164Lu

    International Nuclear Information System (INIS)

    Cardona, M.A.; Hojman, D.; Kreiner, A.J.; Somacal, H.; Davidson, J.; Davidson, M.; Acuna, D. de; Napoli, D.R.; Rico, J.; Burch, R.; Bazzacco, D.; Lenzi, S.M.; Rossi Alvarez, C.; Blasi, N.; Lo Bianco, G.

    1996-01-01

    High spin rotational bands in 162 Lu and 164 Lu have been studied by means of the 139 La( 28 Si,5n) and 139 La( 29(30) Si,4(5)n) reactions respectively. For both nuclei the yrast sequence which is associated with the πh 11/2 x νi 13/2 configuration shows the signature inversion feature. (orig.)

  4. The πNN coupling from high precision np charge exchange at 162 MeV

    International Nuclear Information System (INIS)

    Nilsson, J.; Blomgren, J.; Conde, H.; Elmgren, K.; Olsson, N.; Ericson, T.E.O.; Uppsala Univ.; Jonsson, O.; Nilsson, L.; Loiseau, B.; Ringbom, A.

    1995-02-01

    Differential cross sections for unpolarized neutrons of 162 MeV have been measured to high precision with particular attention to the absolute normalisation. These data can be extrapolated precisely and model-independently to the pion pole and give a πNN coupling constant g 2 =14.6±0.3 or f 2 =0.0808±0.0017. This is higher than recently suggested values. (author) 24 refs.; 3 figs.; 1 tab

  5. Internal motions in H II regions. XII S162 and NGC 7635

    Energy Technology Data Exchange (ETDEWEB)

    Pismis, P; Moreno, M A; Hasse, I [Universidad Nacional Autonoma de Mexico, Mexico City

    1983-01-01

    The apparent structure of S162 and of the bubble nebula (NGC 7635) associated with it is discussed using a number of direct images taken through narrow band (10 A/sup 0/) interference filters in H..cap alpha.., (N II) and in the continuum at lambda6607. The results are discussed together with the radial velocity field of S162 and in particular of the bubble nebula as obtained from photographic Fabry-Perot interferometry. The bubble nebula is shown to be composed of distinct and amorphous very regularly curving arcs, all inscribed on a tenuous slightly ellipsoidal shell of gas expanding at velocity of about 4 km s/sup -1/. The arcs are probably genetically related to the globules which form the caracteristic comet like feature within the bubble nebula. The ionization source of S162 is BD + 60/sup 0/2522 and 071Isub(b)f star classified from our high dispersion spectrum. Our very tentative suggestion is that the brightest globule may be an offshoot fo this star and that the globule has generated the next globule which in turn may have generated the third one. The configuration of NGC 7635 suggests that magnetic fields are likely to be operative in the region. Polarimetry in the optical and in the radio range as well as high resolution infrared studies, high resolution velocity fields are desirable to find a satisfactory model for this nebula.

  6. Extension of the energy range of the experimental activation cross-sections data of longer-lived products of proton induced nuclear reactions on dysprosium up to 65MeV.

    Science.gov (United States)

    Tárkányi, F; Ditrói, F; Takács, S; Hermanne, A; Ignatyuk, A V

    2015-04-01

    Activation cross-sections data of longer-lived products of proton induced nuclear reactions on dysprosium were extended up to 65MeV by using stacked foil irradiation and gamma spectrometry experimental methods. Experimental cross-sections data for the formation of the radionuclides (159)Dy, (157)Dy, (155)Dy, (161)Tb, (160)Tb, (156)Tb, (155)Tb, (154m2)Tb, (154m1)Tb, (154g)Tb, (153)Tb, (152)Tb and (151)Tb are reported in the 36-65MeV energy range, and compared with an old dataset from 1964. The experimental data were also compared with the results of cross section calculations of the ALICE and EMPIRE nuclear model codes and of the TALYS nuclear reaction model code as listed in the latest on-line libraries TENDL 2013. Copyright © 2015. Published by Elsevier Ltd.

  7. Dysprosium doping induced shape and magnetic anisotropy of Fe{sub 3−x}Dy{sub x}O{sub 4} (x=0.01–0.1) nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Richa [School of Sciences, Indira Gandhi National Open University, Maidan Garhi, New Delhi 110068 (India); Department of Physics, ARSD college, University of Delhi, New Delhi 110021 (India); Luthra, Vandna [Department of Physics, Gargi College, Siri Fort Road, New Delhi 110049 (India); Gokhale, Shubha, E-mail: sgokhale@ignou.ac.in [School of Sciences, Indira Gandhi National Open University, Maidan Garhi, New Delhi 110068 (India)

    2016-09-15

    The effect of dysprosium doping on evolution of structural and magnetic properties of magnetite (Fe{sub 3}O{sub 4}) nanoparticles is reported. A standard route of co-precipitation was used for the synthesis of undoped and doped magnetite nanoparticles Fe{sub 3−x}Dy{sub x}O{sub 4} (x=0.0–0.1). Transmission electron microscopy (TEM) shows formation of round shaped particles with diameter in the range of 8–14 nm for undoped sample. On doping beyond x=0.01, the formation of rod like structures is initiated along with the round shaped particles. The number of rods is found to increase with increasing doping concentration. Magnetic characterization using Vibrating Sample Magnetometer (VSM) revealed doping dependent magnetic properties which can be correlated with the crystallite size as determined from X-ray diffraction (XRD). Enhancement in the saturation magnetization in the initial stages of doping can be explained on the basis of incorporation of Dy{sup 3+} ions in the inverse spinel structure at the octahedral site in place of Fe{sup 3+} ions. Subsequent decrease in saturation magnetization observed beyond x=0.03 could be attributed to precipitation of excess Dy in form of dysprosium ferrite phase. - Highlights: • Report on formation of nanorods in magnetite prompted by Dy doping. • Observation of anisotropic magnetic behaviour emanating from the shape anisotropy. • Evidence of Dy{sup 3+} ions occupying octahedral site in place of Fe{sup 3+} ions. • Nanorods envisaged to be useful as catalysts and in biomedical applications.

  8. 40 CFR 417.162 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

    Science.gov (United States)

    2010-07-01

    ... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Liquid Detergents Subcategory § 417.162 Effluent limitations guidelines... available (BPT): (a) For normal liquid detergent operations the following values pertain: Effluent...

  9. Activity in mice of recombinant BCG-EgG1Y162 vaccine for Echinococcus granulosus infection.

    Science.gov (United States)

    Ma, Xiumin; Zhao, Hui; Zhang, Fengbo; Zhu, Yuejie; Peng, Shanshan; Ma, Haimei; Cao, Chunbao; Xin, Yan; Yimiti, Delixiati; Wen, Hao; Ding, Jianbing

    2016-01-01

    Cystic hydatid disease is a zoonotic parasitic disease caused by Echinococcus granulosus which is distributed worldwide. The disease is difficult to treat with surgery removal is the only cure treatment. In the high endemic areas, vaccination of humans is believed a way to protect communities from the disease. In this study we vaccinated BALB/c mice with rBCG-EgG1Y162, and then detected the level of IgG and IgE specifically against the recombinant protein by ELISA, rBCG-EgG1Y162 induced strong and specific cellular and humoral immune responses. In vitro study showed that rBCG-EgG1Y162 vaccine not only promote splenocytes proliferation but also active T cell. In addition, the rBCG-EgG1Y162 induced a protection in the mice against secondary infection of Echinococcus granulosus.

  10. Dysprosium selective potentiometric membrane sensor

    Energy Technology Data Exchange (ETDEWEB)

    Zamani, Hassan Ali, E-mail: haszamani@yahoo.com [Department of Applied Chemistry, Mashhad Branch, Islamic Azad University, Mashhad (Iran, Islamic Republic of); Faridbod, Farnoush; Ganjali, Mohammad Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of)

    2013-03-01

    A novel Dy(III) ion-selective PVC membrane sensor was made using a new synthesized organic compound, 3,4-diamino-N Prime -((pyridin-2-yl)methylene)benzohydrazide (L) as an excellent sensing element. The electrode showed a Nernstian slope of 19.8 {+-} 0.6 mV per decade in a wide concentration range of 1.0 Multiplication-Sign 10{sup -6}-1.0 Multiplication-Sign 10{sup -2} mol L{sup -1}, a detection limit of 5.5 Multiplication-Sign 10{sup -7} mol L{sup -1}, a short conditioning time, a fast response time (< 10 s), and high selectivity towards Dy(III) ion in contrast to other cations. The proposed sensor was successfully used as an indicator electrode in the potentiometric titration of Dy(III) ions with EDTA. The membrane sensor was also applied to the F{sup -} ion indirect determination of some mouth washing solutions and to the Dy{sup 3+} determination in binary mixtures. Highlights: Black-Right-Pointing-Pointer The novelty of this work is based on the high affinity of the ionophore toward the Dy{sup 3+} ions. Black-Right-Pointing-Pointer This technique is very simple, fast and inexpensive and it is not necessary to use sophisticated equipment. Black-Right-Pointing-Pointer The newly developed sensor is superior to the formerly reported Dy{sup 3+} sensors in terms of selectivity.

  11. Mechanical analysis of a $\\beta=0.09 $ 162.5MHz taper HWR cavity

    OpenAIRE

    Fan, Peiliang; Zhu, Feng; Zhong, Hutianxiang; Quan, Shengwen; Liu, Kexin

    2015-01-01

    One superconducting taper-type half-wave resonator (HWR) with frequency of 162.5MHz, \\b{eta} of 0.09 has been developed at Peking University, which is used to accelerate high current proton ($\\sim$ 100mA) and $D^{+}$($\\sim$ 50mA). The radio frequency (RF) design of the cavity has been accomplished. Herein, we present the mechanical analysis of the cavity which is also an important aspect in superconducting cavity design. The frequency shift caused by bath helium pressure and Lorenz force, and...

  12. CERN: Fixed target targets

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1993-03-15

    Full text: While the immediate priority of CERN's research programme is to exploit to the full the world's largest accelerator, the LEP electron-positron collider and its concomitant LEP200 energy upgrade (January, page 1), CERN is also mindful of its long tradition of diversified research. Away from LEP and preparations for the LHC proton-proton collider to be built above LEP in the same 27-kilometre tunnel, CERN is also preparing for a new generation of heavy ion experiments using a new source, providing heavier ions (April 1992, page 8), with first physics expected next year. CERN's smallest accelerator, the LEAR Low Energy Antiproton Ring continues to cover a wide range of research topics, and saw a record number of hours of operation in 1992. The new ISOLDE on-line isotope separator was inaugurated last year (July, page 5) and physics is already underway. The remaining effort concentrates around fixed target experiments at the SPS synchrotron, which formed the main thrust of CERN's research during the late 1970s. With the SPS and LEAR now approaching middle age, their research future was extensively studied last year. Broadly, a vigorous SPS programme looks assured until at least the end of 1995. Decisions for the longer term future of the West Experimental Area of the SPS will have to take into account the heavy demand for test beams from work towards experiments at big colliders, both at CERN and elsewhere. The North Experimental Area is the scene of larger experiments with longer lead times. Several more years of LEAR exploitation are already in the pipeline, but for the longer term, the ambitious Superlear project for a superconducting ring (January 1992, page 7) did not catch on. Neutrino physics has a long tradition at CERN, and this continues with the preparations for two major projects, the Chorus and Nomad experiments (November 1991, page 7), to start next year in the West Area. Delicate neutrino oscillation effects could become visible for the first

  13. Report of AAPM Task Group 162: Software for planar image quality metrology.

    Science.gov (United States)

    Samei, Ehsan; Ikejimba, Lynda C; Harrawood, Brian P; Rong, John; Cunningham, Ian A; Flynn, Michael J

    2018-02-01

    The AAPM Task Group 162 aimed to provide a standardized approach for the assessment of image quality in planar imaging systems. This report offers a description of the approach as well as the details of the resultant software bundle to measure detective quantum efficiency (DQE) as well as its basis components and derivatives. The methodology and the associated software include the characterization of the noise power spectrum (NPS) from planar images acquired under specific acquisition conditions, modulation transfer function (MTF) using an edge test object, the DQE, and effective DQE (eDQE). First, a methodological framework is provided to highlight the theoretical basis of the work. Then, a step-by-step guide is included to assist in proper execution of each component of the code. Lastly, an evaluation of the method is included to validate its accuracy against model-based and experimental data. The code was built using a Macintosh OSX operating system. The software package contains all the source codes to permit an experienced user to build the suite on a Linux or other *nix type system. The package further includes manuals and sample images and scripts to demonstrate use of the software for new users. The results of the code are in close alignment with theoretical expectations and published results of experimental data. The methodology and the software package offered in AAPM TG162 can be used as baseline for characterization of inherent image quality attributes of planar imaging systems. © 2017 American Association of Physicists in Medicine.

  14. Determination of the cross section for (n,p) reaction with producing short-lived nuclei on the 162,163Dy isotopes at 13.5 and 14.8 MeV

    International Nuclear Information System (INIS)

    Luo, Junhua; Feng, Zhifu; An, Li; Jiang, Li; He, Long

    2016-01-01

    Activation cross-sections for the 162 Dy(n,p) 162 Tb and 163 Dy(n,p) 163 Tb reactions have been measured by means of the activation technique and a coaxial HPGe γ-ray detector at 13.5 and 14.8 MeV. The fast neutrons were produced via the 3 H(d,n) 4 He reaction on Pd-300 neutron generator. The natural high-purity Dy 2 O 3 powder was used as target material. Theoretical excitation functions were calculated using the nuclear-reaction codes EMPIRE-3.2 Malta and TALYS-1.6 with default parameters, at neutron energies varying from the reaction threshold to 20 MeV. The results were also discussed and compared with some corresponding values found in the literature, with the comprehensive evaluation data in ENDF/B-VII.1 and JENDF-4.0 libraries, and with the estimates obtained from a published empirical formula based on the statistical model with Q-value dependence and odd–even effects taken into consideration. - Highlights: • The cross sections for the 162 Dy(n,p) 162 Tb and 163 Dy(n,p) 163 Tb have been measured. • 93 Nb(n,2n) 92m Nb was used as a monitor for neutron fluence. • Codes TALYS-1.6 and EMPIRE-3.2 Malta were used to model the reactions. • The results were compared with previous data. • Inconsistency with previous data and with model calculations are noted.

  15. CERN: Fixed target targets

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Full text: While the immediate priority of CERN's research programme is to exploit to the full the world's largest accelerator, the LEP electron-positron collider and its concomitant LEP200 energy upgrade (January, page 1), CERN is also mindful of its long tradition of diversified research. Away from LEP and preparations for the LHC proton-proton collider to be built above LEP in the same 27-kilometre tunnel, CERN is also preparing for a new generation of heavy ion experiments using a new source, providing heavier ions (April 1992, page 8), with first physics expected next year. CERN's smallest accelerator, the LEAR Low Energy Antiproton Ring continues to cover a wide range of research topics, and saw a record number of hours of operation in 1992. The new ISOLDE on-line isotope separator was inaugurated last year (July, page 5) and physics is already underway. The remaining effort concentrates around fixed target experiments at the SPS synchrotron, which formed the main thrust of CERN's research during the late 1970s. With the SPS and LEAR now approaching middle age, their research future was extensively studied last year. Broadly, a vigorous SPS programme looks assured until at least the end of 1995. Decisions for the longer term future of the West Experimental Area of the SPS will have to take into account the heavy demand for test beams from work towards experiments at big colliders, both at CERN and elsewhere. The North Experimental Area is the scene of larger experiments with longer lead times. Several more years of LEAR exploitation are already in the pipeline, but for the longer term, the ambitious Superlear project for a superconducting ring (January 1992, page 7) did not catch on. Neutrino physics has a long tradition at CERN, and this continues with the preparations for two major projects, the Chorus and Nomad experiments (November 1991, page 7), to start next year in the West Area. Delicate neutrino oscillation effects could become

  16. Target laboratory

    International Nuclear Information System (INIS)

    Ephraim, D.C.; Pednekar, A.R.

    1993-01-01

    A target laboratory to make stripper foils for the accelerator and various targets for use in the experiments is set up in the pelletron accelerator facility. The facilities available in the laboratory are: (1) D.C. glow discharge setup, (2) carbon arc set up, and (3) vacuum evaporation set up (resistance heating), electron beam source, rolling mill - all for target preparation. They are described. Centrifugal deposition technique is used for target preparation. (author). 3 figs

  17. Ice targets

    International Nuclear Information System (INIS)

    Pacheco, C.; Stark, C.; Tanaka, N.; Hodgkins, D.; Barnhart, J.; Kosty, J.

    1979-12-01

    This report presents a description of ice targets that were constructed for research work at the High Resolution Spectrometer (HRS) and at the Energetic Pion Channel and Spectrometer (EPICS). Reasons for using these ice targets and the instructions for their construction are given. Results of research using ice targets will be published at a later date

  18. On the relation between the statistical γ-decay and the level density in 162Dy

    International Nuclear Information System (INIS)

    Henden, L.; Bergholt, L.; Guttormsen, M.; Rekstad, J.; Tveter, T.S.

    1994-12-01

    The level density of low-spin states (0-10ℎ) in 162 Dy has been determined from the ground state up to approximately 6 MeV of excitation energy. Levels in the excitation region up to 8 MeV were populated by means of the 163 Dy( 3 He, α) reaction, and the first-generation γ-rays in the decay of these states has been isolated. The energy distribution of the first-generation γ-rays provides a new source of information about the nuclear level density over a wide energy region. A broad peak is observed in the first-generation spectra, and the authors suggest an interpretation in terms of enhanced M1 transitions between different high-j Nilsson orbitals. 30 refs., 9 figs., 2 tabs

  19. np scattering measurements at 162 MeV and the πNN coupling constant

    International Nuclear Information System (INIS)

    Rahm, J.; Blomgren, J.; Conde, H.; Dangtip, S.; Elmgren, K.; Olsson, N.; Roennqvist, T.; Zorro, R.; Ringbom, A.; Tibell, G.; Jonsson, O.; Nilsson, L.; Renberg, P.U.; Ericson, T.E.O.; Loiseau, B.

    1999-01-01

    The differential np scattering cross sections has been measured at 162 MeV in the angular range θ c.m. = 72 angle - 180 angle, using the neutron beam facility at the Svedberg Laboratory in Uppsala. Special attention was paid to the absolute normalization of the data. In the angular range 150 angle - 180 angle, the data are steeper then those of most previous measurements and predictions from energy-dependent partial-wave analyses, or nucleon-nucleon potentials. Moreover, a value of the charged πNN coupling constant, g π± 2 = 14.52 ± 0.26 (f π± 2 = 0.0803 ± 0.0014), is deduced from the data, using a novel extrapolation method. This is in good agreement with the classical text book value, but higher than those determined in recent partial-wave analyses of the nucleon-nucleon data base. (authors)

  20. Pregnancy outcome in 162 women with rheumatic diseases: experience of a university hospital in Turkey.

    Science.gov (United States)

    Davutoğlu, Ebru Alici; Ozel, Aysegul; Yılmaz, Nevin; Madazli, Riza

    2017-12-01

    To evaluate the distribution and the obstetric outcomes of pregnancies with different types of rheumatic diseases managed in our unit. Pregnancies of 162 women with rheumatic diseases, seen for their antenatal care at our department for the period between 2013 and 2017 were included in this retrospective clinical study. Obstetric and perinatal outcomes were main outcome measures. The most encountered rheumatic diseases were SLE (37.7%) followed by Behcet's disease (20.4%) and rheumatoid arthritis (17.3%) in our series. The mean maternal age was 30.6 ± 5.3 and the rate of nulliparity was 38.3% in the overall group. Disease activation occurred in 14.1% of patients. Mean gestational age at delivery was 37.4 ± 3.1 and mean birth weight was 3004 ± 762 g. Stillbirth, neonatal death, fetal growth restriction, preeclampsia and preterm delivery rates were 1.2, 2.4, 17.3, 7.4 and 17.9%, respectively. Antiphospholipid syndrome had the highest incidences for fetal growth restriction (42.9%), preeclampsia (28.6%) and delivery ≤ 34 gestational weeks (42.9%). Pathologic uterine artery Doppler velocimetry was identified in 15 cases (15/162, 9.3%) in which 10 (66.7%) developed preeclampsia and/or fetal growth restriction during follow-up. A majority of women with rheumatic diseases have successful pregnancies and deliver healthy babies, with the close and appropriate rheumatological, obstetric and neonatal monitoring.

  1. CAUGHT IN THE ACT: THE ASSEMBLY OF MASSIVE CLUSTER GALAXIES AT z = 1.62

    International Nuclear Information System (INIS)

    Lotz, Jennifer M.; Ferguson, Henry C.; Grogin, Norman; Koekemoer, Anton M.; Papovich, Casey; Tran, Kim-Vy; Faber, S. M.; Guo Yicheng; Kocevski, Dale; Lee, Kyoung-Soo; McIntosh, Daniel; Momcheva, Ivelina; Rudnick, Gregory; Saintonge, Amelie; Van der Wel, Arjen; Willmer, Christopher

    2013-01-01

    We present the recent merger history of massive galaxies in a spectroscopically confirmed proto-cluster at z = 1.62. Using Hubble Space Telescope WFC3 near-infrared imaging from the Cosmic Assembly Near-infrared Deep Extragalactic Legacy Survey, we select cluster and z ∼ 1.6 field galaxies with M star ≥ 3 × 10 10 M ☉ , to determine the frequency of double nuclei or close companions within projected separations less than 20 kpc co-moving. We find that four out of five spectroscopically confirmed massive proto-cluster galaxies have double nuclei, and 57 +13 -14 % of all M star ≥ 3 × 10 10 M ☉ cluster candidates are observed in either close pair systems or have double nuclei. In contrast, only 11% ± 3% of the field galaxies are observed in close pair/double nuclei systems. After correcting for the contribution from random projections, the implied merger rate per massive galaxy in the proto-cluster is ∼3-10 times higher than the merger rate of massive field galaxies at z ∼ 1.6. Close pairs in the cluster have minor merger stellar mass ratios (M primary : M satellite ≥ 4), while the field pairs consist of both major and minor mergers. At least half of the cluster mergers are gas-poor, as indicated by their red colors and low 24 μm fluxes. Two of the double-nucleated cluster members have X-ray detected active galactic nuclei with L x > 10 43 erg s –1 , and are strong candidates for dual or offset super-massive black holes. We conclude that the massive z = 1.62 proto-cluster galaxies are undergoing accelerated assembly via minor mergers, and discuss the implications for galaxy evolution in proto-cluster environments

  2. Pathologic features of lower extremity arterial lesions in diabetes mellitus:an analysis of 162 patients

    International Nuclear Information System (INIS)

    Guo Xiangjiang; Zhang Jiwei

    2010-01-01

    Objective: To investigate the angiographic manifestations of lower extremity atherosclerotic occlusion in patients with diabetes mellitus. Methods: The angiographic findings of lower extremity in 162 patients with diabetes mellitus were retrospectively analyzed. (1) The arteries of lower extremity were divided into the following four segments: iliac, femoral, popliteal and crural artery. The involvements of these arteries were documented. (2) Based on the lesion's number, location, nature (stricture or occlusion) and length ( 5 cm), the diabetic arterial diseases were categorized. Results: (1) Of 162 diabetic lower limbs, multiple segmental lesions were seen in 131, superficial femoral arterial lesions in 130, and crural arterial lesions in 139, of which 130 arterial lesions had at least two below-the-knee arteries being involved. (2) Based on segmental angiographic classification, a total of 660 vascular lesions were detected, including stricture lesions (33.8%) and occlusive lesions (66.2%). Of the 437 occlusions, 70.5% were located in below-the-knee arteries, and most of which were longer than 10 cm and located in anterior and posterior tibial arteries, while only a few peroneal arteries were involved (P < 0.0001). One hundred and fifty-two lesions were detected in superficial femoral arteries, of which 49 (31.2%) were located at the origin of the superficial femoral artery and 56 (35.7) were in the adductor canal hiatus. Conclusion: The main feature of peripheral arterial disease of lower extremity caused by diabetes mellitus is multi-level atherosclerotic occlusion, the superficial femoral and the crural arteries are most likely to be involved. The lesions of superficial femoral artery are often located at the arterial origin and in the adductor canal hiatus, while the deep femoral artery and the femoral artery are less involved. Long occlusive lesions are more prevalent in crural arteries, especially in anterior and posterior tibial arteries. (J Intervent

  3. Pectin Enhances Bio-Control Efficacy by Inducing Colonization and Secretion of Secondary Metabolites by Bacillus amyloliquefaciens SQY 162 in the Rhizosphere of Tobacco.

    Directory of Open Access Journals (Sweden)

    Kai Wu

    Full Text Available Bacillus amyloliquefaciens is a plant-beneficial Gram-positive bacterium involved in suppressing soil-borne pathogens through the secretion of secondary metabolites and high rhizosphere competence. Biofilm formation is regarded as a prerequisite for high rhizosphere competence. In this work, we show that plant extracts affect the chemotaxis and biofilm formation of B. amyloliquefaciens SQY 162 (SQY 162. All carbohydrates tested induced the chemotaxis and biofilm formation of the SQY 162 strain; however, the bacterial growth rate was not influenced by the addition of carbohydrates. A strong chemotactic response and biofilm formation of SQY 162 were both induced by pectin through stimulation of surfactin synthesis and transcriptional expression of biofilm formation related matrix genes. These results suggested that pectin might serve as an environmental factor in the stimulation of the biofilm formation of SQY 162. Furthermore, in pot experiments the surfactin production and the population of SQY 162 in the rhizosphere significantly increased with the addition of sucrose or pectin, whereas the abundance of the bacterial pathogen Ralstonia decreased. With increased production of secondary metabolites in the rhizosphere of tobacco by SQY 162 and improved colonization density of SQY 162 in the pectin treatment, the disease incidences of bacterial wilt were efficiently suppressed. The present study revealed that certain plant extracts might serve as energy sources or environmental cues for SQY 162 to enhance the population density on tobacco root and bio-control efficacy of tobacco bacterial wilt.

  4. 41 CFR 301-10.162 - When may I use other than coach-class train accommodations?

    Science.gov (United States)

    2010-07-01

    ... 10-TRANSPORTATION EXPENSES Common Carrier Transportation Train § 301-10.162 When may I use other than... require other than coach-class rail accommodations. Exceptional security circumstances are determined by... accommodations on an authorized/approved foreign rail carrier do not provide adequate sanitation or health...

  5. 76 FR 37034 - Certain Employee Remuneration in Excess of $1,000,000 Under Internal Revenue Code Section 162(m)

    Science.gov (United States)

    2011-06-24

    ... Certain Employee Remuneration in Excess of $1,000,000 Under Internal Revenue Code Section 162(m) AGENCY... remuneration in excess of $1,000,000 under the Internal Revenue Code (Code). The proposed regulations clarify... stock options, it is intended that the directors may retain discretion as to the exact number of options...

  6. 33 CFR 162.220 - Hoover Dam, Lake Mead, and Lake Mohave (Colorado River), Ariz.-Nev.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hoover Dam, Lake Mead, and Lake... REGULATIONS § 162.220 Hoover Dam, Lake Mead, and Lake Mohave (Colorado River), Ariz.-Nev. (a) Lake Mead and... the axis of Hoover Dam and that portion of Lake Mohave (Colorado River) extending 4,500 feet...

  7. 25 CFR 162.110 - Can these regulations be administered by tribes, on the Secretary's or on BIA's behalf?

    Science.gov (United States)

    2010-04-01

    ... entered into under the Indian Self-Determination and Education Assistance Act (25 U.S.C. § 450f et seq.). ... 25 Indians 1 2010-04-01 2010-04-01 false Can these regulations be administered by tribes, on the... INTERIOR LAND AND WATER LEASES AND PERMITS General Provisions § 162.110 Can these regulations be...

  8. Interaction of C-terminal truncated human alphaA-crystallins with target proteins.

    Directory of Open Access Journals (Sweden)

    Anbarasu Kumarasamy

    2008-09-01

    Full Text Available Significant portion of alphaA-crystallin in human lenses exists as C-terminal residues cleaved at residues 172, 168, and 162. Chaperone activity, determined with alcohol dehydrogenase (ADH and betaL-crystallin as target proteins, was increased in alphaA(1-172 and decreased in alphaA(1-168 and alphaA(1-162. The purpose of this study was to show whether the absence of the C-terminal residues influences protein-protein interactions with target proteins.Our hypothesis is that the chaperone-target protein binding kinetics, otherwise termed subunit exchange rates, are expected to reflect the changes in chaperone activity. To study this, we have relied on fluorescence resonance energy transfer (FRET utilizing amine specific and cysteine specific fluorescent probes. The subunit exchange rate (k for ADH and alphaA(1-172 was nearly the same as that of ADH and alphaA-wt, alphaA(1-168 had lower and alphaA(1-162 had the lowest k values. When betaL-crystallin was used as the target protein, alphaA(1-172 had slightly higher k value than alphaA-wt and alphaA(1-168 and alphaA(1-162 had lower k values. As expected from earlier studies, the chaperone activity of alphaA(1-172 was slightly better than that of alphaA-wt, the chaperone activity of alphaA(1-168 was similar to that of alphaA-wt and alphaA(1-162 had substantially decreased chaperone activity.Cleavage of eleven C-terminal residues including Arg-163 and the C-terminal flexible arm significantly affects the interaction with target proteins. The predominantly hydrophilic flexible arm appears to be needed to keep the chaperone-target protein complex soluble.

  9. PPARα L162V underlies variation in serum triglycerides and subcutaneous fat volume in young males

    Directory of Open Access Journals (Sweden)

    Clarkson Priscilla M

    2007-08-01

    Full Text Available Abstract Background Of the five sub-phenotypes defining metabolic syndrome, all are known to have strong genetic components (typically 50–80% of population variation. Studies defining genetic predispositions have typically focused on older populations with metabolic syndrome and/or type 2 diabetes. We hypothesized that the study of younger populations would mitigate many confounding variables, and allow us to better define genetic predisposition loci for metabolic syndrome. Methods We studied 610 young adult volunteers (average age 24 yrs for metabolic syndrome markers, and volumetric MRI of upper arm muscle, bone, and fat pre- and post-unilateral resistance training. Results We found the PPARα L162V polymorphism to be a strong determinant of serum triglyceride levels in young White males, where carriers of the V allele showed 78% increase in triglycerides relative to L homozygotes (LL = 116 ± 11 mg/dL, LV = 208 ± 30 mg/dL; p = 0.004. Men with the V allele showed lower HDL (LL = 42 ± 1 mg/dL, LV = 34 ± 2 mg/dL; p = 0.001, but women did not. Subcutaneous fat volume was higher in males carrying the V allele, however, exercise training increased fat volume of the untrained arm in V carriers, while LL genotypes significantly decreased in fat volume (LL = -1,707 ± 21 mm3, LV = 17,617 ± 58 mm3 ; p = 0.002, indicating a systemic effect of the V allele on adiposity after unilateral training. Our study suggests that the primary effect of PPARα L162V is on serum triglycerides, with downstream effects on adiposity and response to training. Conclusion Our results on association of PPARα and triglycerides in males showed a much larger effect of the V allele than previously reported in older and less healthy populations. Specifically, we showed the V allele to increase triglycerides by 78% (p = 0.004, and this single polymorphism accounted for 3.8% of all variation in serum triglycerides in males (p = 0.0037.

  10. 46 CFR 162.050-4 - Incorporation by reference: Where can I get a copy of the publications mentioned in this part?

    Science.gov (United States)

    2010-10-01

    ... ENGINEERING EQUIPMENT Pollution Prevention Equipment § 162.050-4 Incorporation by reference: Where can I get a....org): (1) International Standard ISO 8217 Third edition 2005-11-01, Petroleum products—Fuels (class F)—Specifications of marine fuels (“ISO 8217”), incorporation by reference approved for § 162.050-20. (2...

  11. 34 CFR 222.162 - What disparity standard must a State meet in order to be certified and how are disparities in...

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false What disparity standard must a State meet in order to be certified and how are disparities in current expenditures or revenues per pupil measured? 222.162... of the Act § 222.162 What disparity standard must a State meet in order to be certified and how are...

  12. 42 CFR 84.162 - Man test for gases and vapors; Type C respirators, continuous-flow class and Type CE supplied-air...

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Man test for gases and vapors; Type C respirators, continuous-flow class and Type CE supplied-air respirators; test requirements. 84.162 Section 84.162 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL...

  13. Antiproton Target

    CERN Multimedia

    1980-01-01

    Antiproton target used for the AA (antiproton accumulator). The first type of antiproton production target used from 1980 to 1982 comprised a rod of copper 3mm diameter and 120mm long embedded in a graphite cylinder that was itself pressed into a finned aluminium container. This assembly was air-cooled and it was used in conjunction with the Van der Meer magnetic horn. In 1983 Fermilab provided us with lithium lenses to replace the horn with a view to increasing the antiproton yield by about 30%. These lenses needed a much shorter target made of heavy metal - iridium was chosen for this purpose. The 50 mm iridium rod was housed in an extension to the original finned target container so that it could be brought very close to the entrance to the lithium lens. Picture 1 shows this target assembly and Picture 2 shows it mounted together with the lithium lens. These target containers had a short lifetime due to a combination of beam heating and radiation damage. This led to the design of the water-cooled target in...

  14. HSV-2-Driven Increase in the Expression of α4β7 Correlates with Increased Susceptibility to Vaginal SHIVSF162P3 Infection

    Science.gov (United States)

    Goode, Diana; Truong, Rosaline; Villegas, Guillermo; Calenda, Giulia; Guerra-Perez, Natalia; Piatak, Michael; Lifson, Jeffrey D.; Blanchard, James; Gettie, Agegnehu; Robbiani, Melissa; Martinelli, Elena

    2014-01-01

    The availability of highly susceptible HIV target cells that can rapidly reach the mucosal lymphoid tissues may increase the chances of an otherwise rare transmission event to occur. Expression of α4β7 is required for trafficking of immune cells to gut inductive sites where HIV can expand and it is expressed at high level on cells particularly susceptible to HIV infection. We hypothesized that HSV-2 modulates the expression of α4β7 and other homing receptors in the vaginal tissue and that this correlates with the increased risk of HIV acquisition in HSV-2 positive individuals. To test this hypothesis we used an in vivo rhesus macaque (RM) model of HSV-2 vaginal infection and a new ex vivo model of macaque vaginal explants. In vivo we found that HSV-2 latently infected RMs appeared to be more susceptible to vaginal SHIVSF162P3 infection, had higher frequency of α4β7 high CD4+ T cells in the vaginal tissue and higher expression of α4β7 and CD11c on vaginal DCs. Similarly, ex vivo HSV-2 infection increased the susceptibility of the vaginal tissue to SHIVSF162P3. HSV-2 infection increased the frequencies of α4β7 high CD4+ T cells and this directly correlated with HSV-2 replication. A higher amount of inflammatory cytokines in vaginal fluids of the HSV-2 infected animals was similar to those found in the supernatants of the infected explants. Remarkably, the HSV-2-driven increase in the frequency of α4β7 high CD4+ T cells directly correlated with SHIV replication in the HSV-2 infected tissues. Our results suggest that the HSV-2-driven increase in availability of CD4+ T cells and DCs that express high levels of α4β7 is associated with the increase in susceptibility to SHIV due to HSV-2. This may persists in absence of HSV-2 shedding. Hence, higher availability of α4β7 positive HIV target cells in the vaginal tissue may constitute a risk factor for HIV transmission. PMID:25521298

  15. HSV-2-driven increase in the expression of α4β7 correlates with increased susceptibility to vaginal SHIV(SF162P3) infection.

    Science.gov (United States)

    Goode, Diana; Truong, Rosaline; Villegas, Guillermo; Calenda, Giulia; Guerra-Perez, Natalia; Piatak, Michael; Lifson, Jeffrey D; Blanchard, James; Gettie, Agegnehu; Robbiani, Melissa; Martinelli, Elena

    2014-12-01

    The availability of highly susceptible HIV target cells that can rapidly reach the mucosal lymphoid tissues may increase the chances of an otherwise rare transmission event to occur. Expression of α4β7 is required for trafficking of immune cells to gut inductive sites where HIV can expand and it is expressed at high level on cells particularly susceptible to HIV infection. We hypothesized that HSV-2 modulates the expression of α4β7 and other homing receptors in the vaginal tissue and that this correlates with the increased risk of HIV acquisition in HSV-2 positive individuals. To test this hypothesis we used an in vivo rhesus macaque (RM) model of HSV-2 vaginal infection and a new ex vivo model of macaque vaginal explants. In vivo we found that HSV-2 latently infected RMs appeared to be more susceptible to vaginal SHIVSF162P3 infection, had higher frequency of α4β7high CD4+ T cells in the vaginal tissue and higher expression of α4β7 and CD11c on vaginal DCs. Similarly, ex vivo HSV-2 infection increased the susceptibility of the vaginal tissue to SHIVSF162P3. HSV-2 infection increased the frequencies of α4β7high CD4+ T cells and this directly correlated with HSV-2 replication. A higher amount of inflammatory cytokines in vaginal fluids of the HSV-2 infected animals was similar to those found in the supernatants of the infected explants. Remarkably, the HSV-2-driven increase in the frequency of α4β7high CD4+ T cells directly correlated with SHIV replication in the HSV-2 infected tissues. Our results suggest that the HSV-2-driven increase in availability of CD4+ T cells and DCs that express high levels of α4β7 is associated with the increase in susceptibility to SHIV due to HSV-2. This may persists in absence of HSV-2 shedding. Hence, higher availability of α4β7 positive HIV target cells in the vaginal tissue may constitute a risk factor for HIV transmission.

  16. HSV-2-driven increase in the expression of α4β7 correlates with increased susceptibility to vaginal SHIV(SF162P3 infection.

    Directory of Open Access Journals (Sweden)

    Diana Goode

    2014-12-01

    Full Text Available The availability of highly susceptible HIV target cells that can rapidly reach the mucosal lymphoid tissues may increase the chances of an otherwise rare transmission event to occur. Expression of α4β7 is required for trafficking of immune cells to gut inductive sites where HIV can expand and it is expressed at high level on cells particularly susceptible to HIV infection. We hypothesized that HSV-2 modulates the expression of α4β7 and other homing receptors in the vaginal tissue and that this correlates with the increased risk of HIV acquisition in HSV-2 positive individuals. To test this hypothesis we used an in vivo rhesus macaque (RM model of HSV-2 vaginal infection and a new ex vivo model of macaque vaginal explants. In vivo we found that HSV-2 latently infected RMs appeared to be more susceptible to vaginal SHIVSF162P3 infection, had higher frequency of α4β7high CD4+ T cells in the vaginal tissue and higher expression of α4β7 and CD11c on vaginal DCs. Similarly, ex vivo HSV-2 infection increased the susceptibility of the vaginal tissue to SHIVSF162P3. HSV-2 infection increased the frequencies of α4β7high CD4+ T cells and this directly correlated with HSV-2 replication. A higher amount of inflammatory cytokines in vaginal fluids of the HSV-2 infected animals was similar to those found in the supernatants of the infected explants. Remarkably, the HSV-2-driven increase in the frequency of α4β7high CD4+ T cells directly correlated with SHIV replication in the HSV-2 infected tissues. Our results suggest that the HSV-2-driven increase in availability of CD4+ T cells and DCs that express high levels of α4β7 is associated with the increase in susceptibility to SHIV due to HSV-2. This may persists in absence of HSV-2 shedding. Hence, higher availability of α4β7 positive HIV target cells in the vaginal tissue may constitute a risk factor for HIV transmission.

  17. Pitfalls of CT for deep neck abscess imaging assessment: a retrospective review of 162 cases.

    Science.gov (United States)

    Chuang, S Y; Lin, H T; Wen, Y S; Hsu, F J

    2013-01-01

    To investigate the diagnostic value of contrast-enhanced computed tomography (CT) for the prediction of deep neck abscesses in different deep neck spaces and to evaluate the false-positive results. We retrospectively analysed the clinical charts, CT examinations, surgical findings, bacteriology, pathological examinations and complications of hospitalised patients with a diagnosis of deep neck abscess from 2004 to 2010. The positive predictive values (PPV) for the prediction of abscesses by CT scan in different deep neck spaces were calculated individually on the basis of surgical findings. A total of 162 patients were included in this study. All patients received both intravenous antibiotics and surgical drainage. The parapharyngeal space was the most commonly involved space. The overall PPV for the prediction of deep neck abscess with contrast-enhanced CT was 79.6%. The PPV was 91.3% when more than one deep neck space was involved but only 50.0% in patients with isolated retropharyngeal abscesses. In the false-positive group, cellulitis was the most common final result, followed by cystic degeneration of cervical metastases. Five specimens taken intra-operatively revealed malignancy and four of these were not infected. There are some limitations affecting the differentiation of abscesses and cellulitis, particularly in the retropharyngeal space. A central necrotic cervical metastatic lymph node may sometimes also mimic a simple pyogenic deep neck abscess on both clinical pictures and CT images. Routine biopsy of the tissue must be performed during surgical drainage.

  18. 162.5 MHz digital low-level radio frequency control monitoring system design and implementation

    International Nuclear Information System (INIS)

    Zhang Ruifeng; Wang Xianwu; Xu Zhe; Yi Xiaoping

    2014-01-01

    162.5 MHz high-frequency low-level control system self-developed by Institute of Modern Physics for ADS project took digital technology. All parameters' reading and writing, including loop parameter setting, open and close-loop operation, and condition monitoring, were achieved through the monitoring system. The system used lightweight client-server working mode that client running in the PC sent command data, server running on high-frequency digital low level system responded instructions to complete parameter monitoring and control. The system consisted of three parts. Firstly, server hardware system was constructed based on Atera Stratix Ⅲ family of field-programmable gate array (FPGA) development board. Secondly, the server software system was designed based on Micro C/OS Ⅱ real-time operating systems and lightweight TCP/IP protocol stack, and finally a client PC program was designed based on MFC. After a long test, it was indicated that the monitoring system works properly and stably. TCP sends and receives throughput reached 11.931038 Mbps and 8.117624 Mbps. (authors)

  19. Correlation between the progressive cytoplasmic expression of a novel small heat shock protein (Hsp16.2) and malignancy in brain tumors

    International Nuclear Information System (INIS)

    Pozsgai, Eva; Gomori, Eva; Szigeti, Andras; Boronkai, Arpad; Gallyas, Ferenc Jr; Sumegi, Balazs; Bellyei, Szabolcs

    2007-01-01

    Small heat shock proteins are molecular chaperones that protect proteins against stress-induced aggregation. They have also been found to have anti-apoptotic activity and to play a part in the development of tumors. Recently, we identified a new small heat shock protein, Hsp16.2 which displayed increased expression in neuroectodermal tumors. Our aim was to investigate the expression of Hsp16.2 in different types of brain tumors and to correlate its expression with the histological grade of the tumor. Immunohistochemistry with a polyclonal antibody to Hsp16.2 was carried out on formalin-fixed, paraffin-wax-embedded sections using the streptavidin-biotin method. 91 samples were examined and their histological grade was defined. According to the intensity of Hsp16.2 immunoreactivity, low (+), moderate (++), high (+++) or none (-) scores were given. Immunoblotting was carried out on 30 samples of brain tumors using SDS-polyacrylamide gel electrophoresis and Western-blotting. Low grade (grades 1–2) brain tumors displayed low cytoplasmic Hsp16.2 immunoreactivity, grade 3 tumors showed moderate cytoplasmic staining, while high grade (grade 4) tumors exhibited intensive cytoplasmic Hsp16.2 staining. Immunoblotting supported the above mentioned results. Normal brain tissue acted as a negative control for the experiment, since the cytoplasm did not stain for Hsp16.2. There was a positive correlation between the level of Hsp16.2 expression and the level of anaplasia in different malignant tissue samples. Hsp16.2 expression was directly correlated with the histological grade of brain tumors, therefore Hsp16.2 may have relevance as becoming a possible tumor marker

  20. Correlation between the progressive cytoplasmic expression of a novel small heat shock protein (Hsp16.2 and malignancy in brain tumors

    Directory of Open Access Journals (Sweden)

    Gallyas Ferenc

    2007-12-01

    Full Text Available Abstract Background Small heat shock proteins are molecular chaperones that protect proteins against stress-induced aggregation. They have also been found to have anti-apoptotic activity and to play a part in the development of tumors. Recently, we identified a new small heat shock protein, Hsp16.2 which displayed increased expression in neuroectodermal tumors. Our aim was to investigate the expression of Hsp16.2 in different types of brain tumors and to correlate its expression with the histological grade of the tumor. Methods Immunohistochemistry with a polyclonal antibody to Hsp16.2 was carried out on formalin-fixed, paraffin-wax-embedded sections using the streptavidin-biotin method. 91 samples were examined and their histological grade was defined. According to the intensity of Hsp16.2 immunoreactivity, low (+, moderate (++, high (+++ or none (- scores were given. Immunoblotting was carried out on 30 samples of brain tumors using SDS-polyacrylamide gel electrophoresis and Western-blotting. Results Low grade (grades 1–2 brain tumors displayed low cytoplasmic Hsp16.2 immunoreactivity, grade 3 tumors showed moderate cytoplasmic staining, while high grade (grade 4 tumors exhibited intensive cytoplasmic Hsp16.2 staining. Immunoblotting supported the above mentioned results. Normal brain tissue acted as a negative control for the experiment, since the cytoplasm did not stain for Hsp16.2. There was a positive correlation between the level of Hsp16.2 expression and the level of anaplasia in different malignant tissue samples. Conclusion Hsp16.2 expression was directly correlated with the histological grade of brain tumors, therefore Hsp16.2 may have relevance as becoming a possible tumor marker.

  1. Religiousness as a Predictor of Suicide: An Analysis of 162 European Regions.

    Science.gov (United States)

    Stack, Steven; Laubepin, Frederique

    2018-01-25

    Research on religion as a protective factor has been marked by four recurrent limitations: (1) an overemphasis on the United States, a nation where religiosity is relatively high; (2) a neglect of highly secularized zones of the world, where religiousness may be too weak to affect suicide; (3) restriction of religiousness to religious affiliation, a construct which may miss capturing other dimensions of religiousness such as the importance of religion in one's life; and (4) an overwhelming use of the nation as a unit of analysis, which masks variation in religiousness within nations. The present article addresses these limitations by performing a cross-national test of the following hypothesis: The greater the strength of subjective religiousness, the lower the suicide rate, using small units of analysis for a secularized area of the world. All data refer to 162 regions within 22 European nations. Data were extracted from two large databases, EUROSTAT and the European Social Surveys (ESS Round 4), and merged using NUTS-2 (Nomenclature of Statistical Territorial Units) regions as the unit of analysis. Controls are incorporated for level of economic development, education, and measures of economic strain. The results of a multiple regression analysis demonstrated that controlling for the other constructs in the model, religiousness is associated with lower suicide rates, confirming the hypothesis. Even in secularized European nations, where there is a relatively weak moral community to reinforce religion, religiousness acts as a protective factor against suicide. Future work is needed to explore the relationship in other culture zones of the world. © 2018 The American Association of Suicidology.

  2. Genitourinary injuries after traffic accidents: Analysis of a registry of 162,690 victims.

    Science.gov (United States)

    Terrier, Jean-Etienne; Paparel, Philippe; Gadegbeku, Blandine; Ruffion, Alain; Jenkins, Lawrence C; N'Diaye, Amina

    2017-06-01

    Traffic accidents are the most frequent cause of genitourinary injuries (GUI). Kidney injuries after trauma have been well described. However, there exists a paucity of data on other traumatic GUI after traffic accidents. The objective of this study was to analyze the frequency and type of all GUI, by user category, after traffic accidents. Patient cases were extracted from the trauma registry of the French department of Rhone from 1996 to 2013. We assessed the urogenital injuries presented by each of road user's categories. Severity injuries were coded with the Abbreviated Injury Scale and the Injury Severity Score. Kidney trauma was mapped with the classification of the American Association for the Surgery of Trauma. Multivariate prediction models were used for analysis of data. Of 162,690 victims, 963 presented with GUI (0.59%). 47% were motorcyclists, 22% were in a car, 18% on bicycles, and 9% were pedestrians. The most common organ injury was kidney (41%) followed by testicular (23%). Among the 208 motorists with a GUI, kidney (70%), bladder (10%), and adrenal gland (9%) were the most frequent lesions. Among the 453 motorcyclist victims with GUI, kidney (35%) and testicular (38%) traumas were the most frequent and 62% of injuries involved external genitalia. There were 175 cyclists with GUI, 70% of injuries involved external genitalia; penile traumas (23%) were the most frequent. In total, there were 395 kidney injuries, most being low grade. According to the American Association for the Surgery of Trauma kidney injuries were grade I, 59%; grade II, 11%; grade III, 16%; grade IV, 9%; grade V, 3%; and indeterminate, 2%. GUI is an infrequent trauma after traffic accidents, with kidneys being the most commonly injured. Physicians must maintain a high awareness for external genitalia injuries in motorcyclists and cyclists. Prognostic and epidemiologic study, level III.

  3. Surgical management of juvenile nasopharyngeal angiofibroma: analysis of 162 cases from 1995 to 2012.

    Science.gov (United States)

    Huang, Yang; Liu, Zhuofu; Wang, Jingjing; Sun, Xicai; Yang, Lei; Wang, Dehui

    2014-08-01

    The purpose of this study was to report on a series of 162 patients presenting with juvenile nasopharyngeal angiofibroma in a single academic hospital during the past 17 years, in an effort to compare outcomes between open and transnasal endoscopic approach, and to define an ideal treatment strategy. Patients who received either open or endoscopic surgery with a minimum follow-up of 6 months were selected. Local control and complications were compared between groups. Retrospectively, clinical data, surgical reports, pre- and postoperative images, and follow-up information were reviewed and analyzed. All patients were male subjects from 8 to 41 years old. Ninety-six patients were treated by transpalatal or transmaxillary approach, and the remaining 66 patients were treated using transnasal endoscopic approach with/without labiogingival incision. When compared to the open surgery group, the endoscopic surgery group showed a lower median intraoperative blood loss (800 vs. 1100 mL, P = .017) and a lower number of postoperative complications (one vs. 10). In addition, recurrence statistically correlated with Radkowski's classification and patient age. Transnasal endoscopic approach can be successfully used for Radkowski's stages I-IIb tumors and selective IIc-IIIb lesions, allowing for less blood loss, fewer postoperative complications, and a lower percentage of recurrence in comparison to open surgery. The management of recurrent tumor is complex, should be individually tailored, and should take into account tumor location, patient age, complications of treatment, and the possibility of spontaneous involution, to better define treatment strategy. © 2014 The American Laryngological, Rhinological and Otological Society, Inc.

  4. DISCOVERY OF A STRONG LENSING GALAXY EMBEDDED IN A CLUSTER AT z = 1.62

    International Nuclear Information System (INIS)

    Wong, Kenneth C.; Suyu, Sherry H.; Tran, Kim-Vy H.; Papovich, Casey J.; Momcheva, Ivelina G.; Brammer, Gabriel B.; Koekemoer, Anton M.; Brodwin, Mark; Gonzalez, Anthony H.; Kacprzak, Glenn G.; Rudnick, Gregory H.; Halkola, Aleksi

    2014-01-01

    We identify a strong lensing galaxy in the cluster IRC 0218 (also known as XMM-LSS J02182–05102) that is spectroscopically confirmed to be at z = 1.62, making it the highest-redshift strong lens galaxy known. The lens is one of the two brightest cluster galaxies and lenses a background source galaxy into an arc and a counterimage. With Hubble Space Telescope (HST) grism and Keck/LRIS spectroscopy, we measure the source redshift to be z S = 2.26. Using HST imaging in ACS/F475W, ACS/F814W, WFC3/F125W, and WFC3/F160W, we model the lens mass distribution with an elliptical power-law profile and account for the effects of the cluster halo and nearby galaxies. The Einstein radius is θ E =0.38 −0.01 +0.02 arcsec (3.2 −0.1 +0.2 kpc) and the total enclosed mass is M tot (<θ E )=1.8 −0.1 +0.2 ×10 11 M ⊙ . We estimate that the cluster environment contributes ∼10% of this total mass. Assuming a Chabrier initial mass function (IMF), the dark matter fraction within θ E is f DM Chab =0.3 −0.3 +0.1 , while a Salpeter IMF is marginally inconsistent with the enclosed mass (f DM Salp =−0.3 −0.5 +0.2 ). The total magnification of the source is μ tot =2.1 −0.3 +0.4 . The source has at least one bright compact region offset from the source center. Emission from Lyα and [O III] are likely to probe different regions in the source

  5. Targeted Learning

    CERN Document Server

    van der Laan, Mark J

    2011-01-01

    The statistics profession is at a unique point in history. The need for valid statistical tools is greater than ever; data sets are massive, often measuring hundreds of thousands of measurements for a single subject. The field is ready to move towards clear objective benchmarks under which tools can be evaluated. Targeted learning allows (1) the full generalization and utilization of cross-validation as an estimator selection tool so that the subjective choices made by humans are now made by the machine, and (2) targeting the fitting of the probability distribution of the data toward the targe

  6. Target preparation

    International Nuclear Information System (INIS)

    Hinn, G.M.

    1984-01-01

    A few of the more interesting of the 210 targets prepared in the Laboratory last year are listed. In addition the author continues to use powdered silver mixed with /sup 9,10/BeO to produce sources for accelerator radio dating of Alaskan and South Polar snow. Currently, he is trying to increase production by multiple sample processing. Also the author routinely makes 3 μg/cm 2 cracked slacked carbon stripper foils and is continuing research with some degree of success in making enriched 28 Si targets starting with the oxide

  7. Study of elastic pion scattering from 9Be, 28Si, 58Ni, and 208Pb at 162 MeV

    International Nuclear Information System (INIS)

    Devereux, M.J.

    1979-05-01

    Elastic pion scattering from 9 Be, 28 Si, 58 Ni, and 208 Pb at 162 MeV is analyzed and compared with an optical model theory which incorporates a pion--nucleon range. Excellent fits to the data are obtained in all but one case. The fitted values of the pion--nucleon range, as well as other fitted values are listed. 108 references

  8. Separation of boron isotopes by ion exchange chromatography: studies with Duolite-162, a type-II resin

    International Nuclear Information System (INIS)

    Sharma, B.K.; Subramanian, R.; Balasubramanian, R.; Mathur, P.K.

    1994-01-01

    The selection of resin plays an important role in the process of separation of boron isotopes by ion exchange chromatography. The determination of (i) ion exchange capacity of Duolite-162 resin for hydroxyl - chloride exchange, (ii) hydroxyl - borate exchange, (iii) isotopic exchange separation factor by batch method and (iv) effect of concentration of boric acid on isotopic exchange separation factor to test the suitability of the above resin for this process are discussed in this report. (author)

  9. New candidates for active asteroids: Main-belt (145) Adeona, (704) Interamnia, (779) Nina, (1474) Beira, and near-Earth (162,173) Ryugu

    Science.gov (United States)

    Busarev, Vladimir V.; Makalkin, Andrei B.; Vilas, Faith; Barabanov, Sergey I.; Scherbina, Marina P.

    2018-04-01

    For the first time, spectral signs of subtle coma activity were observed for four main-belt primitive asteroids (145) Adeona, (704) Interamnia, (779) Nina, and (1474) Beira around their perihelion distances in September 2012, which were interpreted as manifestations of the sublimation of H2O ice in/under the surface matter (Busarev et al., 2015a, 2015b). We confirm the phenomenon for Nina when it approached perihelion in September 2016. At the same time, based on results of spectral observations of near-Earth asteroid (162,173) Ryugu (Vilas, 2008) being a target of Japan's Hayabusa 2 space mission, we suspected a periodic similar transient activity on the Cg-type asteroid. However, unlike the main-belt primitive asteroids demonstrating sublimation of ices close to their perihelion distances, the effect on Ryugu was apparently registered near aphelion. To explain the difference, we calculated the subsolar temperature depending on heliocentric distance of the asteroids, considered qualitative models of internal structure of main-belt and near-Earth primitive asteroids including ice and performed some analytical estimations. Presumed temporal sublimation/degassing activity of Ryugu is a sign of a residual frozen core in its interior. This could be an indication of a relatively recent transition of the asteroid from the main asteroid belt to the near-Earth area.

  10. Development and validation of an event-specific quantitative PCR method for genetically modified maize MIR162.

    Science.gov (United States)

    Takabatake, Reona; Masubuchi, Tomoko; Futo, Satoshi; Minegishi, Yasutaka; Noguchi, Akio; Kondo, Kazunari; Teshima, Reiko; Kurashima, Takeyo; Mano, Junichi; Kitta, Kazumi

    2014-01-01

    A novel real-time PCR-based analytical method was developed for the event-specific quantification of a genetically modified (GM) maize event, MIR162. We first prepared a standard plasmid for MIR162 quantification. The conversion factor (Cf) required to calculate the genetically modified organism (GMO) amount was empirically determined for two real-time PCR instruments, the Applied Biosystems 7900HT (ABI7900) and the Applied Biosystems 7500 (ABI7500) for which the determined Cf values were 0.697 and 0.635, respectively. To validate the developed method, a blind test was carried out in an interlaboratory study. The trueness and precision were evaluated as the bias and reproducibility of relative standard deviation (RSDr). The determined biases were less than 25% and the RSDr values were less than 20% at all evaluated concentrations. These results suggested that the limit of quantitation of the method was 0.5%, and that the developed method would thus be suitable for practical analyses for the detection and quantification of MIR162.

  11. DISCOVERY OF A STRONG LENSING GALAXY EMBEDDED IN A CLUSTER AT z = 1.62

    Energy Technology Data Exchange (ETDEWEB)

    Wong, Kenneth C.; Suyu, Sherry H. [Institute of Astronomy and Astrophysics, Academia Sinica (ASIAA), P.O. Box 23-141, Taipei 10617, Taiwan (China); Tran, Kim-Vy H.; Papovich, Casey J. [George P. and Cynthia W. Mitchell Institute for Fundamental Physics and Astronomy, Department of Physics and Astronomy, Texas A and M University, College Station, TX 77843 (United States); Momcheva, Ivelina G. [Astronomy Department, Yale University, New Haven, CT 06511 (United States); Brammer, Gabriel B.; Koekemoer, Anton M. [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Brodwin, Mark [Department of Physics and Astronomy, University of Missouri, 5110 Rockhill Road, Kansas City, MO 64110 (United States); Gonzalez, Anthony H. [Department of Astronomy, University of Florida, Gainesville, FL 32611 (United States); Kacprzak, Glenn G. [Swinburne University of Technology, Victoria 3122 (Australia); Rudnick, Gregory H. [Department of Physics and Astronomy, The University of Kansas, Malott Room 1082, 1251 Wescoe Hall Drive, Lawrence, KS 66045 (United States); Halkola, Aleksi

    2014-07-10

    We identify a strong lensing galaxy in the cluster IRC 0218 (also known as XMM-LSS J02182–05102) that is spectroscopically confirmed to be at z = 1.62, making it the highest-redshift strong lens galaxy known. The lens is one of the two brightest cluster galaxies and lenses a background source galaxy into an arc and a counterimage. With Hubble Space Telescope (HST) grism and Keck/LRIS spectroscopy, we measure the source redshift to be z {sub S} = 2.26. Using HST imaging in ACS/F475W, ACS/F814W, WFC3/F125W, and WFC3/F160W, we model the lens mass distribution with an elliptical power-law profile and account for the effects of the cluster halo and nearby galaxies. The Einstein radius is θ{sub E}=0.38{sub −0.01}{sup +0.02} arcsec (3.2{sub −0.1}{sup +0.2} kpc) and the total enclosed mass is M {sub tot}(<θ{sub E})=1.8{sub −0.1}{sup +0.2}×10{sup 11} M{sub ⊙}. We estimate that the cluster environment contributes ∼10% of this total mass. Assuming a Chabrier initial mass function (IMF), the dark matter fraction within θ{sub E} is f{sub DM}{sup Chab}=0.3{sub −0.3}{sup +0.1}, while a Salpeter IMF is marginally inconsistent with the enclosed mass (f{sub DM}{sup Salp}=−0.3{sub −0.5}{sup +0.2}). The total magnification of the source is μ{sub tot}=2.1{sub −0.3}{sup +0.4}. The source has at least one bright compact region offset from the source center. Emission from Lyα and [O III] are likely to probe different regions in the source.

  12. The role of dysprosium on the structural and magnetic properties of (Nd{sub 1−x}Dy{sub x}){sub 2}Fe{sub 14}B nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, Hamed; Ghasemi, Ali, E-mail: ali13912001@yahoo.com; Mozaffarinia, Reza; Tavoosi, Majid

    2017-02-15

    In current work, Nd2Fe14B nanoparticles was synthesized by sol-gel method. Dysprosium powders were added into Nd2Fe14B nanoparticles by mechanical alloying process in order to enhancement of coercivity. The phase analysis, structure, and magnetic properties of annealed (Nd{sub 1−x}Dy{sub x}){sub 2}Fe{sub 14}B nanoparticles with different Dy-content (x=0.1, 0.2, 0.3, 0.4, 0.5, 0.6) were investigated by employing X-ray diffraction, X-ray photoelectron spectroscopy, energy dispersive spectroscopy, field emission scanning electron microscope, transmission electron microscope and vibrating sample magnetometer techniques. The results showed that with an increase in Dy amounts, the coercivity of particles increased from 2.9 kOe to 13.4 kOe and then decreased to 5.6 kOe. By adding an optimum amount of Dy (x=0.4), the coercivity was significantly increased from 2.9 kOe to 13.4 kOe. The average particle size of annealed (Nd{sub 1−x}Dy{sub x}){sub 2}Fe{sub 14}B nanoparticles was below 10 nm. Magnetization reversal studies indicate that the coercivity of milled and annealed (Nd{sub 1−x}Dy{sub x}){sub 2}Fe{sub 14}B nanoparticles is controlled by the nucleation of reversed magnetic domains. The experimental results in the angular dependence of coercivity for (Nd{sub 1−x}Dy{sub x}){sub 2}Fe{sub 14}B permanent magnets showed that the normalized coercivity of the permanent magnets H{sub c}(θ)/H{sub c}(0) increases from 1 to about 1.2–1.5 with increasing θ from 0 to about π/3, for x=0.4–0.6. - Highlights: • Dy was added to Nd{sub 2}Fe{sub 14}B nanoparticles to improve the coercivity. • A maximum squareness ratio of 0.99 was obtained. • The average particle size decreased with an increase in Dy-content.

  13. Coulomb excitation of rotational states in the 162Dy nucleus in the framework of the generalized semiclassical approximation

    International Nuclear Information System (INIS)

    Bolotin, Yu.L.; Gonchar, V.Yu.; Chekanov, N.A.

    1985-01-01

    Coulomb excitation of rotational states induced in heavyion collisions is treated in the framework of the generalized semiclassical approximation. The Hamiltonian of the system under consideration involves not only Coulomb forces (monopole, quadrupole, and hexadecapole) but as well a real nuclear potential in the form of the deformed Woods-Saxon potential. Strong dependence of the excitation probability on the interference between the Coulomb and nuclear interactions is shown. Calculations are carried out for the reaction 40 Ar+ 162 Dy at E=148.6 MeV. The calculated Coulomb excitation probabilities agree satisfactory with the corresponding experimental values

  14. Persamaan Unsur Pokok Pada Suatu Merek Terkenal (Analisis Putusan MA Nomor 162 K/Pdt.Sus-HKI/2014

    Directory of Open Access Journals (Sweden)

    Dandi Pahusa

    2016-04-01

    Full Text Available Abstract: Equation Basic Element In A Famous Brand (Analysis of the Decision of the Supreme Court Number 162 K / Pdt.Sus-IPR / 2014. Criteria for determining the equation of the constituents in a well-known brand that is the similarity of images, sounds, names, words, letters, numbers, color composition or a combination of these elements, either for goods or services that are similar or dissimilar based on general knowledge of the public, the brand earned a reputation as a massive campaign, and with evidence of the trademark registration in several countries. The impact of the decision of the Supreme Court Number 162 K / Pdt.Sus-IPR / 2014 for brand owners who have registered and well-known to always protect its brand, namely by taking into account the bad faith of the owner of the other brands. If there are other brands that have been registered in the Directorate General of Intellectual Property and published in General News Brands, the owner of the mark that has been registered in advance immediately appealed and the cancellation of the trademark. Abstrak: Persamaan Unsur Pokok Pada Suatu Merek Terkenal (Analisis atas Putusan MA Nomor 162 K/Pdt.Sus-HKI/2014. Kriteria penentuan persamaan unsur pokok pada suatu merek terkenal yaitu adanya kemiripan gambar, bunyi, nama, kata, huruf-huruf, angka-angka, susunan warna atau kombinasi dari unsur-unsur tersebut, baik terhadap barang atau jasa yang sejenis maupun tidak sejenis yang didasarkan pada pengetahuan umum masyarakat, reputasi merek yang diperoleh karena promosi besar-besaran, dan disertai bukti pendaftaran merek tersebut di beberapa negara. Dampak dari putusan Mahkamah Agung Nomor 162 K/Pdt.Sus-HKI/2014 bagi pemilik merek yang telah terdaftar dan terkenal agar selalu melindungi mereknya yaitu dengan memperhatikan adanya itikad tidak baik dari pemilik merek lain. Apabila terdapat merek lain yang telah terdaftar di Dirjen HKI dan diumumkan dalam Berita Umum Merek, maka pemilik merek yang telah

  15. X-ray diffraction studies of 145MeV proton-irradiated AlBeMet 162

    Directory of Open Access Journals (Sweden)

    Mohamed Elbakhshwan

    2016-08-01

    Full Text Available AlBeMet 162 (Materion Co., formerly Brush Wellman has been irradiated with 145MeV protons up to 1.2×1020cm−2 fluence, with irradiation temperatures in the range of 100–220°C. Macroscopic post-irradiation evaluation on the evolution of mechanical and thermal properties was integrated with a comprehensive X-ray- diffraction study using high-energy monochromatic and polychromatic X-ray beams, which offered a microscopic view of the irradiation damage effects on AlBeMet. The study confirmed the stability of the metal–matrix composite, its resistance to proton damage, and the continuing separation of the two distinct phases, fcc aluminum and hcp beryllium, following irradiation. Furthermore, based on the absence of inter-planar distance change during proton irradiation, it was confirmed that the stacking faults and clusters on the Al (111 planes are stable, and thus can migrate from the cascade region and be absorbed at various sinks. XRD analysis of the unirradiated AlBeMet 162 showed clear change in the texture of the fcc phase with orientation especially in the Al (111 reflection which exhibits a “non-perfect” six-fold symmetry, implying lack of isotropy in the composite.

  16. Different Phenotypes of the Two Chinese Probands with the Same c.889G>A (p.C162Y Mutation in COCH Gene Verify Different Mechanisms Underlying Autosomal Dominant Nonsyndromic Deafness 9.

    Directory of Open Access Journals (Sweden)

    Qi Wang

    Full Text Available By analyzing the different phenotypes of two Chinese DFNA9 families with the same mutation located in the intervening region between the LCCL and vWFA domains of cochlin and testing the functional changes in the mutant cochlin, we investigated the different pathogeneses for mutations in LCCL and vWFA domains.Targeted next-generation sequencing for deafness-related genes was used to identify the mutation in the proband in family #208. The probands of family #208 and family #32 with the same p.C162Y mutation were followed for more than 3 years to evaluate the progression of hearing loss and vestibular dysfunction using pure-tone audiometry, caloric testing, electrocochleogram, vestibular-evoked myogenic potential, and video head-impulse test. The disruption of normal cleavage to produce secreted LCCL domain fragments and the tendency to form aggregations of mutant cochlins were tested by in vitro cell experiments.The two families showed different clinical symptoms. Family #32 was identified as having early-onset, progressive sensorineural hearing loss, similar to the symptoms in DFNA9 patients with cochlin mutations in the vWFA domain. The proband of family #208 endured late-onset recurrent paroxysmal vertigo attacks and progressively deteriorating hearing, similar to symptoms in those with cochlin mutations in the LCCL domain. We therefore suggest that the disrupted cleavage of the LCCL domain fragment is likely to cause vestibular dysfunction, and aggregation of mutant cochlin caused by mutations in the vWFA domain is responsible for early-onset hearing loss. The p.C162Y mutation causes either disruption of LCCL domain fragment cleavage or aggregation of mutant cochlin, resulting in the different phenotypes in the two families.This study demonstrates that DFNA9 families with the same genotype may have significantly different phenotypes. The mutation site in cochlin is related to the pathological mechanism underlying the different phenotypes.

  17. 26 CFR 1.162-10T - Questions and answers relating to the deduction of employee benefits under the Tax Reform Act of...

    Science.gov (United States)

    2010-04-01

    ... of employee benefits under the Tax Reform Act of 1984; certain limits on amounts deductible... and Corporations § 1.162-10T Questions and answers relating to the deduction of employee benefits... amendment of section 404(b) by the Tax Reform Act of 1984 affect the deduction of employee benefits under...

  18. Ambtscriminaliteit aangegeven? : Een onderzoek naar het opvolgen van en kennis over de wettelijke verplichting tot aangifte van artikel 162 Sv misdrijven

    NARCIS (Netherlands)

    Vries Robbé, E. de; Cornelissens, A.; Ferwerda, H.

    2008-01-01

    Dit is een onderzoek naar de werking van de aangifteplicht bij ambtscriminaliteit (art 162 Sv). Het gaat dan bijvoorbeeld om het aannemen van steekpenningen en misdrijven waarbij ambtenaren een bijzondere ambtsplicht schenden. De aangifteplicht raakt de klokkenluidersregeling en maakt onderdeel uit

  19. 19 CFR 162.23 - Seizure under section 596(c), Tariff Act of 1930, as amended (19 U.S.C. 1595a(c)).

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Seizure under section 596(c), Tariff Act of 1930... SEIZURE Seizures § 162.23 Seizure under section 596(c), Tariff Act of 1930, as amended (19 U.S.C. 1595a(c)). (a) Mandatory seizures. The following, if introduced or attempted to be introduced into the United...

  20. Relationships between the functional PPARalpha Leu162Val polymorphism and obesity, type 2 diabetes, dyslipidaemia, and related quantitative traits in studies of 5799 middle-aged white people

    DEFF Research Database (Denmark)

    Sparsø, Thomas; Hussain, Meena S; Andersen, Gitte

    2007-01-01

    Peroxisome proliferator-activated receptor-alpha (PPARalpha) is a nuclear receptor capable of regulating the expression of genes involved in peroxisomal and mitochondrial beta-oxidation pathways. The common Leu162Val polymorphism in the gene encoding PPARalpha has inconsistently shown association...

  1. 24 CFR 1000.162 - How will a recipient know that non-dwelling structures assisted under the IHBG program meet the...

    Science.gov (United States)

    2010-04-01

    ...-dwelling structures assisted under the IHBG program meet the requirements of 1000.160? 1000.162 Section... that non-dwelling structures assisted under the IHBG program meet the requirements of 1000.160? (a) The... non-dwelling structure meets the limitation requirements of § 1000.160. If the recipient develops...

  2. Ameliorating effect of TI-1-162, a hydroxyindenone derivative, against TNBS-induced rat colitis is mediated through suppression of RIP/ASK-1/MAPK signaling.

    Science.gov (United States)

    Gurung, Pallavi; Banskota, Suhrid; Katila, Nikita; Gautam, Jaya; Kadayat, Tara Man; Choi, Dong-Young; Lee, Eung Seok; Jeong, Tae Cheon; Kim, Jung-Ae

    2018-05-15

    The pathogenesis of inflammatory bowel disease (IBD) is associated with production of immense pro-inflammatory cytokines including TNF-α. Once generated, TNF-α stimulates production of various pro-inflammatory cytokines and disrupts mucosal barrier by inducing inflamed mucosal epithelial cell death. In the present study, we investigated inhibitory effects of TI-1-162, a hydroxyindenone derivative, against TNF-α-induced and TNBS-induced colon inflammation. TI-1-162 showed inhibitory effect on the TNF-α-induced adhesion of U937 monocytic cells to HT-29 colonic epithelial cells (IC 50 = 0.83 ± 0.12 μM), which is an in vitro model representing the initial step of colitis. In addition, TI-1-162 suppressed TNF-α-stimulated caspase-3 activation and HT-29 cell apoptosis. These in vitro inhibitory activities of TI-1-162 correlated to recovery changes in in vivo colon tissues, such as downregulation of adhesion molecules (ICAM-1, VCAM-1) and chemokines (CCL11, CXCL1, CXCL2, CXCL3, CX3CL1) revealed by gene expression array and Western blot analyses. Such molecular recovery of colon epithelium from TNBS-treated rats corresponded to the recovery in body weight, colon weight/length, and myeloperoxidase level by TI-1-162 (10 and 30 mg/kg/day, orally). In relation to action mechanism, TI-1-162 did not disturb TNF-α binding to its receptor, but suppressed phosphorylation of RIP-1, ASK-1, JNK and p38, and nuclear translocation of NF-kB and AP-1, which corresponded to down regulation of inflammatory cytokines in TNF-α-treated cells (HT-29 and U937) and TNBS-treated rat colon tissues. Taken together, the results indicate that the protective effects of TI-1-162 against colon inflammation and epithelial cell death are associated with its inhibitory action in RIP/ASK-1/MAPK signaling pathway downstream to TNF receptor 1. Copyright © 2018 Elsevier B.V. All rights reserved.

  3. Heavy-ion targets

    International Nuclear Information System (INIS)

    Adair, H.L.; Kobisk, E.H.

    1985-01-01

    This chapter examines the characteristics of targets required in heavy-ion accelerator physics experiments. The effects of target parameters on heavy-ion experimental results are reviewed. The target fabrication and characterization techniques used to minimize experimental problems during heavy-ion bombardment are described. Topics considered include target thickness and uniformity, target lifetime, target purity, substrate materials, Doppler shift effects, metal preparations, and target preparation methods

  4. Calculated single-proton levels for nuclei with N equal to 152, 154, 156, 158, 160 and 162

    International Nuclear Information System (INIS)

    Moeller, P.; Nix, J.R.; Swiatecki, W.

    1986-09-01

    The decay properties of nuclei in many cases depend strongly on the quantum numbers of the single-particle levels in the vicinity of the Fermi surface. A striking illustration is the prolonged fission half-lives of odd nuclei relative to their even neighbors. The hindrance factor depends on the spin of unpaired odd particle and increases with increasing spin of the odd particle. The effect has been studied theoretically. For 257 Fm the hindrance factor is almost ten orders of magnitude. The computer code for calculating nuclear masses calculates single-particle levels at the deformations considered as one step in the calculations. We have run this code at the ground state deformation of all nuclei considered in the 1981 mass study and stored the calculated single-particle levels on permanent mass storage. A computer code has been constructed for extracting levels of nuclei that are specified to the program and plotting them. In this report we consider single-proton levels for even-N nuclei in the range 152 ≤ N ≤ 162. Six such plots are included in this report. The levels are plotted relative to the Fermi surface of each nucleus. We also include tables of the plotted single-particle levels since it is not always possible to determine the spin from an inspection of the plots, when levels are overlapping. 6 figs

  5. The pathologic effect of a novel neomorphic Fgf9(Y162C allele is restricted to decreased vision and retarded lens growth.

    Directory of Open Access Journals (Sweden)

    Oliver Puk

    Full Text Available Fibroblast growth factor (Fgf signalling plays a crucial role in many developmental processes. Among the Fgf pathway ligands, Fgf9 (UniProt: P54130 has been demonstrated to participate in maturation of various organs and tissues including skeleton, testes, lung, heart, and eye. Here we establish a novel Fgf9 allele, discovered in a dominant N-ethyl-N-nitrosourea (ENU screen for eye-size abnormalities using the optical low coherence interferometry technique. The underlying mouse mutant line Aca12 was originally identified because of its significantly reduced lens thickness. Linkage studies located Aca12 to chromosome 14 within a 3.6 Mb spanning interval containing the positional candidate genes Fgf9 (MGI: 104723, Gja3 (MGI: 95714, and Ift88 (MGI: 98715. While no sequence differences were found in Gja3 and Ift88, we identified an A→G missense mutation at cDNA position 770 of the Fgf9 gene leading to an Y162C amino acid exchange. In contrast to previously described Fgf9 mutants, Fgf9(Y162C carriers were fully viable and did not reveal reduced body-size, male-to-female sexual reversal or skeletal malformations. The histological analysis of the retina as well as its basic functional characterization by electroretinography (ERG did not show any abnormality. However, the analysis of head-tracking response of the Fgf9(Y162C mutants in a virtual drum indicated a gene-dosage dependent vision loss of almost 50%. The smaller lenses in Fgf9(Y162C suggested a role of Fgf9 during lens development. Histological investigations showed that lens growth retardation starts during embryogenesis and continues after birth. Young Fgf9(Y162C lenses remained transparent but developed age-related cataracts. Taken together, Fgf9(Y162C is a novel neomorphic allele that initiates microphakia and reduced vision without effects on organs and tissues outside the eye. Our data point to a role of Fgf9 signalling in primary and secondary lens fiber cell growth. The results

  6. SAJCC 162.indd

    African Journals Online (AJOL)

    ARTICLE. SAJCC August 2014, Vol. 30, No. 1. 5. The needs of patient family members in ..... has been done in all sectors to improve the quality of life after the .... Leske JS. Needs of relatives of critically ill patients: A follow-up. Heart Lung 1986 ...

  7. SAJCC 162.indd

    African Journals Online (AJOL)

    premature infants, children who died within 2 hours of admission, or children transferred .... [7] The mean difference in probability represented the bias in .... in terms of risk-adjusted mortality rates. ... The age and diagnostic category distribution.

  8. X-ray diffraction studies on merohedrally twinned Δ1-62NtNBCe1-A crystals of the sodium/bicarbonate cotransporter.

    Science.gov (United States)

    Gill, Harindarpal S; Dutcher, Lauren; Boron, Walter F; Patel, Samir; Guay-Woodford, Lisa M

    2013-07-01

    NBCe1-A membrane-embedded macromolecules that cotransport sodium and bicarbonate ions across the bilayer serve to maintain acid-base homeostasis throughout the body. Defects result in a number of renal and eye disorders, including type-II renal tubular acidosis and cataracts. Here, crystals of a human truncated mutant of the cytoplasmic N-terminal domain of NBCe1 (Δ1-62NtNBCe1-A) are reported that diffract X-rays to 2.4 Å resolution. The crystal symmetry of Δ1-62NtNBCe1-A is of space group P31 with pseudo-P3121 symmetry and it has a hemihedral twin fraction of 33.0%. The crystals may provide insight into the pathogenic processes observed in a subset of patients with truncating and point mutations in the gene encoding NBCe1.

  9. Evidence for an association between the Leu162Val polymorphism of the PPARalpha gene and decreased fasting serum triglyceride levels in glucose tolerant subjects

    DEFF Research Database (Denmark)

    Nielsen, Eva-Maria D; Hansen, Lars; Echwald, Søren Morgenthaler

    2003-01-01

    The aim of the study was to investigate whether genetic variation in the peroxisome proliferator-activated receptor-alpha (PPARalpha) is associated with type 2 diabetes and altered lipid or carbohydrate metabolism in glucose tolerant subjects. Mutation analyses of PPARalpha were performed in 56...... type 2 diabetic patients. Six variants were identified: IVS3 + 76T>C, IVS3-19C>T, IVS4 + 35C>T, Leu162Val, Arg178Gly and Ala268Val. In a case-control study comprising 738 type 2 diabetic patients and 524 glucose tolerant subjects, the three exon variants did not show any significant differences...... in allele frequencies between type 2 diabetic patients and control subjects. The functional Leu162Val polymorphism was further investigated in genotype-phenotype studies involving 340 young, healthy subjects and 502 middle-aged glucose tolerant subjects. The young, healthy subjects who were heterozygous...

  10. Organelle targeting: third level of drug targeting

    Directory of Open Access Journals (Sweden)

    Sakhrani NM

    2013-07-01

    Full Text Available Niraj M Sakhrani, Harish PadhDepartment of Cell and Molecular Biology, BV Patel Pharmaceutical Education and Research Development (PERD Centre, Gujarat, IndiaAbstract: Drug discovery and drug delivery are two main aspects for treatment of a variety of disorders. However, the real bottleneck associated with systemic drug administration is the lack of target-specific affinity toward a pathological site, resulting in systemic toxicity and innumerable other side effects as well as higher dosage requirement for efficacy. An attractive strategy to increase the therapeutic index of a drug is to specifically deliver the therapeutic molecule in its active form, not only into target tissue, nor even to target cells, but more importantly, into the targeted organelle, ie, to its intracellular therapeutic active site. This would ensure improved efficacy and minimize toxicity. Cancer chemotherapy today faces the major challenge of delivering chemotherapeutic drugs exclusively to tumor cells, while sparing normal proliferating cells. Nanoparticles play a crucial role by acting as a vehicle for delivery of drugs to target sites inside tumor cells. In this review, we spotlight active and passive targeting, followed by discussion of the importance of targeting to specific cell organelles and the potential role of cell-penetrating peptides. Finally, the discussion will address the strategies for drug/DNA targeting to lysosomes, mitochondria, nuclei and Golgi/endoplasmic reticulum.Keywords: intracellular drug delivery, cancer chemotherapy, therapeutic index, cell penetrating peptides

  11. A Microbiomic Analysis in African Americans with Colonic Lesions Reveals Streptococcus sp.VT162 as a Marker of Neoplastic Transformation

    Directory of Open Access Journals (Sweden)

    Hassan Brim

    2017-11-01

    Full Text Available Increasing evidence suggests a role of the gut microbiota in colorectal carcinogenesis (CRC. To detect bacterial markers of colorectal cancer in African Americans a metabolomic analysis was performed on fecal water extracts. DNA from stool samples of adenoma and healthy subjects and from colon cancer and matched normal tissues was analyzed to determine the microbiota composition (using 16S rDNA and genomic content (metagenomics. Metagenomic functions with discriminative power between healthy and neoplastic specimens were established. Quantitative Polymerase Chain Reaction (q-PCR using primers and probes specific to Streptococcus sp. VT_162 were used to validate this bacterium association with neoplastic transformation in stool samples from two independent cohorts of African Americans and Chinese patients with colorectal lesions. The metabolomic analysis of adenomas revealed low amino acids content. The microbiota in both cancer vs. normal tissues and adenoma vs. normal stool samples were different at the 16S rRNA gene level. Cross-mapping of metagenomic data led to 9 markers with significant discriminative power between normal and diseased specimens. These markers identified with Streptococcus sp. VT_162. Q-PCR data showed a statistically significant presence of this bacterium in advanced adenoma and cancer samples in an independent cohort of CRC patients. We defined metagenomic functions from Streptococcus sp. VT_162 with discriminative power among cancers vs. matched normal and adenomas vs. healthy subjects’ stools. Streptococcus sp. VT_162 specific 16S rDNA was validated in an independent cohort. These findings might facilitate non-invasive screening for colorectal cancer.

  12. A Small Molecule, Which Competes with MAdCAM-1, Activates Integrin α4β7 and Fails to Prevent Mucosal Transmission of SHIV-SF162P3.

    Directory of Open Access Journals (Sweden)

    Géraldine Arrode-Brusés

    2016-06-01

    Full Text Available Mucosal HIV-1 transmission is inefficient. However, certain viral and host characteristics may play a role in facilitating HIV acquisition and systemic expansion. Cells expressing high levels of integrin α4β7 have been implicated in favoring the transmission process and the infusion of an anti-α4β7 mAb (RM-Act-1 prior to, and during a repeated low-dose vaginal challenge (RLDC regimen with SIVmac251 reduced SIV acquisition and protected the gut-associated lymphoid tissues (GALT in the macaques that acquired SIV. α4β7 expression is required for lymphocyte trafficking to the gut lamina propria and gut inductive sites. Several therapeutic strategies that target α4β7 have been shown to be effective in treating inflammatory conditions of the intestine, such as inflammatory bowel disease (IBD. To determine if blocking α4β7 with ELN, an orally available anti-α4 small molecule, would inhibit SHIV-SF162P3 acquisition, we tested its ability to block MAdCAM-1 (α4β7 natural ligand and HIV-gp120 binding in vitro. We studied the pharmacokinetic profile of ELN after oral and vaginal delivery in macaques. Twenty-six macaques were divided into 3 groups: 9 animals were treated with ELN orally, 9 orally and vaginally and 8 were used as controls. All animals were challenged intra-vaginally with SHIV-SF162P3 using the RLDC regimen. We found that ELN did not protect macaques from SHIV acquisition although it reduced the SHIV-induced inflammatory status during the acute phase of infection. Notably, integrins can exist in different activation states and, comparing the effect of ELN and the anti-α4β7 mAb RM-Act-1 that reduced susceptibility to SIV infection, we determined that ELN induces the active conformation of α4β7, while RM-Act-1 inhibits its activation through an allosteric mechanism. These results suggest that inhibition of α4β7 activation may be necessary to reduce susceptibility to SIV/SHIV infection and highlight the complexity of anti

  13. Deuterium pass through target

    International Nuclear Information System (INIS)

    Alger, D.L.

    1975-01-01

    A neutron emitting target is described for use in neutron generating apparatus including a deuteron source and an accelerator vacuum chamber. The target consists of a tritium-containing target layer, a deuteron accumulation layer, and a target support containing passages providing communication between the accumulation layer and portions of the surface of the support exposed to the accelerator vacuum chamber. With this arrangement, deuterons passing through the target layer and implanting in and diffusing through the accumulation layer, diffuse into the communicating passages and are returned to the accelerator vacuum chamber. The invention allows the continuous removal of deuterons from the target in conventional water cooled neutron generating apparatus. Preferably, the target is provided with thin barrier layers to prevent undesirable tritium diffusion out of the target layer, as well as deuteron diffusion into the target layer

  14. Molecular Targets for Targeted Radionuclide Therapy

    International Nuclear Information System (INIS)

    Mather, S.J.

    2009-01-01

    Molecular targeted radionuclide cancer therapy is becoming of increasing importance, especially for disseminated diseases. Systemic chemotherapies often lack selectivity while targeted radionuclide therapy has important advantages as the radioactive cytotoxic unit of the targeting vector is specifically directed to the cancer, sparing normal tissues. The principle strategy to improve cancer selectivity is to couple therapeutic agents to tumour-targeting vectors. In targeted radionuclide therapy (TRT), the cytotoxic portion of the conjugates normally contains a therapeutic radiometal immobilised by a bifunctional chelator. The aim is therefore to use as ligand-targeted therapeutics vectors coupled to Auger-, alpha- and/or beta-emitting radionuclides. An advantage of using radiation instead of chemotherapeutics as the cytotoxic agent is the so called 'crossfire effect'. This allows sterilisation of tumour cells that are not directly targeted due to heterogeneity in target molecule expression or inhomogeneous vector delivery. However, before the targeting ligands can be selected, the target molecule on the tumour has to be selected. It should be uniquely expressed, or at least highly overexpressed, on or in the target cells relative to normal tissues. The target should be easily accessible for ligand delivery and should not be shed or down- regulated after ligand binding. An important property of a receptor (or antigen) is its potential to be internalized upon binding of the ligand. This provides an active uptake mechanism and allows the therapeutic agent to be trapped within the tumour cells. Molecular targets of current interest include: Receptors: G-protein coupled receptors are overexpressed on many major human tumours. The prototype of these receptors are somatostatin receptors which show very high density in neuroendocrine tumours, but there are many other most interesting receptors to be applied for TRT. The targeting ligands for these receptors are

  15. Monitoring production target thickness

    International Nuclear Information System (INIS)

    Oothoudt, M.A.

    1993-01-01

    Pion and muon production targets at the Clinton P. Anderson Meson Physics Facility consist of rotating graphite wheels. The previous target thickness monitoring Procedure scanned the target across a reduced intensity beam to determine beam center. The fractional loss in current across the centered target gave a measure of target thickness. This procedure, however, required interruption of beam delivery to experiments and frequently indicated a different fractional loss than at normal beam currents. The new monitoring Procedure compares integrated ups and downs toroid current monitor readings. The current monitors are read once per minute and the integral of readings are logged once per eight-hour shift. Changes in the upstream to downstream fractional difference provide a nonintrusive continuous measurement of target thickness under nominal operational conditions. Target scans are now done only when new targets are installed or when unexplained changes in the current monitor data are observed

  16. Charged particle fusion targets

    International Nuclear Information System (INIS)

    Bangerter, R.O.; Meeker, D.J.

    1977-01-01

    The power, voltage, energy and other requirements of electron and ion beam fusion targets are reviewed. Single shell, multiple shell and magnetically insulated target designs are discussed. Questions of stability are also considered. In particular, it is shown that ion beam targets are stabilized by an energy spread in the ion beam

  17. Liquid helium target

    International Nuclear Information System (INIS)

    Fujii, Y.; Kitami, T.; Torikoshi, M.

    1984-12-01

    A liquid helium target system has been built and used for the experiment on the reaction 4 He(γ, p). The target system has worked satisfactorily; the consumption rate of liquid helium is 360 ml/h and the cryogenic system retains liquid helium for about ten hours. The structure, operation and performance of the target system are reported. (author)

  18. Graphite targets at LAMPF

    International Nuclear Information System (INIS)

    Brown, R.D.; Grisham, D.L.

    1983-01-01

    Rotating polycrystalline and stationary pyrolytic graphite target designs for the LAMPF experimental area are described. Examples of finite element calculations of temperatures and stresses are presented. Some results of a metallographic investigation of irradiated pyrolytic graphite target plates are included, together with a brief description of high temperature bearings for the rotating targets

  19. Wake Shield Target Protection

    International Nuclear Information System (INIS)

    Valmianski, Emanuil I.; Petzoldt, Ronald W.; Alexander, Neil B.

    2003-01-01

    The heat flux from both gas convection and chamber radiation on a direct drive target must be limited to avoid target damage from excessive D-T temperature increase. One of the possibilities of protecting the target is a wake shield flying in front of the target. A shield will also reduce drag force on the target, thereby facilitating target tracking and position prediction. A Direct Simulation Monte Carlo (DSMC) code was used to calculate convection heat loads as boundary conditions input into ANSYS thermal calculations. These were used for studying the quality of target protection depending on various shapes of shields, target-shield distance, and protective properties of the shield moving relative to the target. The results show that the shield can reduce the convective heat flux by a factor of 2 to 5 depending on pressure, temperature, and velocity. The protective effect of a shield moving relative to the target is greater than the protective properties of a fixed shield. However, the protective effect of a shield moving under the drag force is not sufficient for bringing the heat load on the target down to the necessary limit. Some other ways of diminishing heat flux using a protective shield are discussed

  20. Development of distributed target

    CERN Document Server

    Yu Hai Jun; Li Qin; Zhou Fu Xin; Shi Jin Shui; Ma Bing; Chen Nan; Jing Xiao Bing

    2002-01-01

    Linear introduction accelerator is expected to generate small diameter X-ray spots with high intensity. The interaction of the electron beam with plasmas generated at the X-ray converter will make the spot on target increase with time and debase the X-ray dose and the imaging resolving power. A distributed target is developed which has about 24 pieces of thin 0.05 mm tantalum films distributed over 1 cm. due to the structure adoption, the distributed target material over a large volume decreases the energy deposition per unit volume and hence reduces the temperature of target surface, then reduces the initial plasma formalizing and its expansion velocity. The comparison and analysis with two kinds of target structures are presented using numerical calculation and experiments, the results show the X-ray dose and normalized angle distribution of the two is basically the same, while the surface of the distributed target is not destroyed like the previous block target

  1. Polarized targets and beams

    International Nuclear Information System (INIS)

    Meyer, W.

    1985-01-01

    First the experimental situation of the single-pion photoproduction and the photodisintegration of the deuteron is briefly discussed. Then a description of the Bonn polarization facilities is given. The point of main effort is put on the polarized target which plays a vital role in the program. A facility for photon induced double polarization experiments at ELSA will be presented in section 4. Properties of a tensor polarized deuteron target are discussed in section 5. The development in the field of polarized targets, especially on new target materials, enables a new generation of polarized target experiments with (polarized) electrons. Some comments on the use of a polarized target in combination with electron beams will be discussed in section 6. Electron deuteron scattering from a tensor polarized deuteron target is considered and compared with other experimental possibilities. (orig./HSI)

  2. Disturbances of ligand potency and enhanced degradation of the human glycine receptor at affected positions G160 and T162 originally identified in patients suffering from hyperekplexia

    Directory of Open Access Journals (Sweden)

    Sinem eAtak

    2015-12-01

    Full Text Available Ligand-binding of Cys-loop receptors is determined by N-terminal extracellular loop structures from the plus as well as from the minus side of two adjacent subunits in the pentameric receptor complex. An aromatic residue in loop B of the glycine receptor (GlyR undergoes direct interaction with the incoming ligand via cation-π interactions. Recently we showed that mutated residues in loop B identified from human patients suffering from hyperekplexia disturb ligand-binding. Here, we exchanged the affected human residues by amino acids found in related members of the Cys-loop receptor family to determine the effects of side chain volume for ion channel properties. GlyR variants were characterized in vitro following transfection into cell lines in order to analyze protein expression, trafficking, degradation and ion channel function. GlyR α1 G160 mutations significantly decrease glycine potency arguing for a positional effect on neighboring aromatic residues and consequently glycine-binding within the ligand-binding pocket. Disturbed glycinergic inhibition due to T162 α1 mutations is an additive effect of affected biogenesis and structural changes within the ligand-binding site. Protein trafficking from the ER towards ER-Golgi intermediate compartment, the secretory Golgi pathways and finally the cell surface is largely diminished, but still sufficient to deliver ion channels that are functional at least at high glycine concentrations. The majority of T162 mutant protein accumulates in the ER and is conducted to ER-associated proteasomal degradation. Hence, G160 is an important determinant during glycine binding. In contrast, T162 assigns primarily receptor biogenesis whereas exchanges in functionality are secondary effects thereof.

  3. High prevalence of Arginine to Glutamine Substitution at 98, 141 and 162 positions in Troponin I (TNNI3 associated with hypertrophic cardiomyopathy among Indians

    Directory of Open Access Journals (Sweden)

    Rani Deepa

    2012-08-01

    Full Text Available Abstract Background Troponin I (TNNI3 is the inhibitory subunit of the thin filament regulatory complex Troponin, which confers calcium-sensitivity to striated muscle actomyosin ATPase activity. Mutations (2-7% in this gene had been reported in hypertrophic cardiomyopathy patients (HCM. However, the frequencies of mutations and associated clinical presentation have not been established in cardiomyopathy patients of Indian origin, hence we have undertaken this study. Methods We have sequenced all the exons, including the exon-intron boundaries of TNNI3 gene in 101 hypertrophic cardiomyopathy patients (HCM, along with 160 healthy controls, inhabited in the same geographical region of southern India. Results Our study revealed a total of 16 mutations. Interestingly, we have observed Arginine to Glutamine (R to Q mutation at 3 positions 98, 141 and 162, exclusively in HCM patients with family history of sudden cardiac death. The novel R98Q was observed in a severe hypertrophic obstructive cardiomyopathy patient (HOCM. The R141Q mutation was observed in two familial cases of severe asymmetric septal hypertrophy (ASH++. The R162Q mutation was observed in a ASH++ patient with mean septal thickness of 29 mm, and have also consists of allelic heterogeneity by means of having one more synonymous (E179E mutation at g.4797: G → A: in the same exon 7, which replaces a very frequent codon (GAG: 85% with a rare codon (GAA: 14%. Screening for R162Q mutation in all the available family members revealed its presence in 9 individuals, including 7 with allelic heterogeneity (R162Q and E179E of which 4 were severely affected. We also found 2 novel SNPs, (g.2653; G → A and g.4003 C → T exclusively in HCM, and in silico analysis of these SNPs have predicted to cause defect in recognition/binding sites for proteins responsible for proper splicing. Conclusion Our study has provided valuable information regarding the prevalence of TNNI3 mutations in

  4. [Interest of lactate micro-dosage in scalp and umbilical cord in cases of abnormal fetal heart rate during labor. Prospective study on 162 patients].

    Science.gov (United States)

    Paris, A; Maurice-Tison, S; Coatleven, F; Vandenbossche, F; Dallay, D; Horovitz, J

    2012-06-01

    To compare the interest of lactate microanalysis with pH measurement (Gold Standard procedure) in cord blood and fetal scalp blood samples for the assessment of abnormal fetal heart rate (FHR) during labour. A prospective observational study conducted from July 1st 2007 till March 31st 2008 on 162 patients with abnormal FHR during labour. Sampling failure for scalp lactate was less than 1 % compared to a failure of 10.5 % for scalp pH (Pinterest. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

  5. Phenomenological descriptions of the Yrast bands in sup(160,162,164,166)Yb nuclei band crossings and moments of inertia

    International Nuclear Information System (INIS)

    El Zaiki, M.I.; Nafie, H.O.; Abd El Mageed, K.E.

    1992-01-01

    Two methods of calculations have been used to fit the previously presented data on rotationally aligned quasiparticle bands in sup(160,162,164,166)Yb. Backbendings of moment of inertia of the Yrast states can be reproduced reasonably well. The energy levels and the effective moment of inertia for both gs and s-band are calculated and compared with the experimental data. Band crossing interpretations are discussed for each nucleus. The interaction strength calculations are presented. (author). 17 refs., 7 figs., 4 tabs

  6. Nova target experiments

    International Nuclear Information System (INIS)

    Drake, R.P.

    1985-11-01

    The Nova laser, at the Lawrence Livermore National Laboratory, provides unique opportunities for target experiments. It has unprecedented energy on target and significant flexibility. The paper presented by John Hunt described the capabilities and the status of Nova. This paper discusses plans for future experiments using Nova, and the present status of target experiments. We plan to perform high-quality physics experiments that exploit the unique capabilities of Nova. Because this is our goal, we are fielding an extensive array of well-characterized target diagnostics to measure the emissions from the target. The first section of this paper discusses the basic target diagnostics. We are also taking care to quantify the performance of the laser

  7. Targeting and Persuasive Advertising

    OpenAIRE

    Egli, Alain (Autor/in)

    2015-01-01

    Firms face a prisoner's dilemma when advertising in a competitive environment. In a Hotelling framework with persuasive advertisingfirms counteract this prisoner's dilemma with targeting. The firms even solve the prisoner's problem if targeted advertising is effective enough. Advertising turns from wasteful competition into profits. This is in contrast to wasteful competition as argument for regulations. A further result is maximum advertising differentiation: thefirms target their advertisin...

  8. The ISOLDE target robots

    CERN Multimedia

    Maximilein Brice

    2002-01-01

    ISOLDE targets need to be changed frequently, around 80 times per year. The high radiation levels do not permit this to be done by human hands and the target changes are effected by 2 industrial robots (picture _01). On the left, in the distance, the front-end of the GPS (General Purpose Separator) is seen, while the HRS (High Resolution Separator) is at the right. Also seen are the doors to the irradiated-target storage.

  9. Deuterium high pressure target

    International Nuclear Information System (INIS)

    Perevozchikov, V.V.; Yukhimchuk, A.A.; Vinogradov, Yu.I.

    2001-01-01

    The design of the deuterium high-pressure target is presented. The target having volume of 76 cm 3 serves to provide the experimental research of muon catalyzed fusion reactions in ultra-pure deuterium in the temperature range 80-800 K under pressures of up to 150 MPa. The operation of the main systems of the target is described: generation and purification of deuterium gas, refrigeration, heating, evacuation, automated control system and data collection system

  10. Targeted Radionuclide Therapy

    Directory of Open Access Journals (Sweden)

    David Cheng

    2011-10-01

    Full Text Available Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose.

  11. Targeted Radionuclide Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ersahin, Devrim, E-mail: devrimersahin@yahoo.com; Doddamane, Indukala; Cheng, David [Department of Diagnostic Radiology, School of Medicine, Yale University, 333 Cedar St., New Haven, CT 06520 (United States)

    2011-10-11

    Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose.

  12. Target Assembly Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Target Assembly Facility integrates new armor concepts into actual armored vehicles. Featuring the capability ofmachining and cutting radioactive materials, it...

  13. Targeted Radionuclide Therapy

    International Nuclear Information System (INIS)

    Ersahin, Devrim; Doddamane, Indukala; Cheng, David

    2011-01-01

    Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose

  14. Targeting the tumor microenvironment

    Energy Technology Data Exchange (ETDEWEB)

    Kenny, P.A.; Lee, G.Y.; Bissell, M.J.

    2006-11-07

    Despite some notable successes cancer remains, for the most part, a seemingly intractable problem. There is, however, a growing appreciation that targeting the tumor epithelium in isolation is not sufficient as there is an intricate mutually sustaining synergy between the tumor epithelial cells and their surrounding stroma. As the details of this dialogue emerge, new therapeutic targets have been proposed. The FDA has already approved drugs targeting microenvironmental components such as VEGF and aromatase and many more agents are in the pipeline. In this article, we describe some of the 'druggable' targets and processes within the tumor microenvironment and review the approaches being taken to disrupt these interactions.

  15. Construction and immunogenicity of replication-competent adenovirus 5 host range mutant recombinants expressing HIV-1 gp160 of SF162 and TV1 strains.

    Science.gov (United States)

    Hidajat, Rachmat; Kuate, Seraphin; Venzon, David; Kalyanaraman, Vaniambadi; Kalisz, Irene; Treece, James; Lian, Ying; Barnett, Susan W; Robert-Guroff, Marjorie

    2010-05-21

    An HIV Env immunogen capable of eliciting broad immunity is critical for a successful vaccine. We constructed and characterized adenovirus 5 host range mutant (Ad5hr) recombinants encoding HIV(SF162) gp160 (subtype B) and HIV(TV1) gp160 (subtype C). Immunization of mice with one or both induced cellular immunity to subtype B and C peptides by ELISpot, and antibody responses with high binding titers to HIV Env of subtypes A, B, C, and E. Notably, Ad5hr-HIV(TV1) gp160 induced better cellular immunity than Ad5hr-HIV(SF162) gp160, either alone or following co-administration. Thus, the TV1 Env recombinant alone may be sufficient for eliciting immune responses against both subtype B and C envelopes. Further studies of Ad5hr-HIV(TV1) gp160 in rhesus macaques will evaluate the suitability of this insert for a future phase I clinical trial using a replication-competent Ad4 vector. Published by Elsevier Ltd.

  16. A TALE OF DWARFS AND GIANTS: USING A z = 1.62 CLUSTER TO UNDERSTAND HOW THE RED SEQUENCE GREW OVER THE LAST 9.5 BILLION YEARS

    International Nuclear Information System (INIS)

    Rudnick, Gregory H.; Tran, Kim-Vy; Papovich, Casey; Momcheva, Ivelina; Willmer, Christopher

    2012-01-01

    We study the red sequence in a cluster of galaxies at z = 1.62 and follow its evolution over the intervening 9.5 Gyr to the present day. Using deep YJK s imaging with the HAWK-I instrument on the Very Large Telescope, we identify a tight red sequence and construct its rest-frame i-band luminosity function (LF). There is a marked deficit of faint red galaxies in the cluster that causes a turnover in the LF. We compare the red-sequence LF to that for clusters at z 0.6. In this model the cluster accretes blue galaxies from the field whose star formation is quenched and who are subsequently allowed to merge. We find that three to four mergers among cluster galaxies during the 4 Gyr between z = 1.62 and z = 0.6 match the observed LF evolution between the two redshifts. The inferred merger rate is consistent with other studies of this cluster. Our result supports the picture that galaxy merging during the major growth phase of massive clusters is an important process in shaping the red-sequence population at all luminosities.

  17. Target reactor development problems

    International Nuclear Information System (INIS)

    Lathrop, K.D.; Vigil, J.C.

    1977-01-01

    Target-blanket design studies are discussed for an accelerator-breeder concept employing a linear accelerator in conjunction with a modified conventional power reactor to produce both fissile fuel and power. The following problems in target and blanket system design are discussed: radiation damage, heat removal, neutronic design, and economics

  18. The CNGS target

    CERN Multimedia

    Patrice Loïez

    2005-01-01

    The CERN Neutrinos to Gran Sasso (CNGS) target ‘magazine’ of five target units. Each unit contains a series of 10-cm long graphite rods distributed over a length of 2 m. It is designed to maximize the number of secondary particles produced and hence the number of neutrinos. One unit is used at a time to prevent over heating.

  19. Targeted radionuclide therapy

    African Journals Online (AJOL)

    target for which a speci c treatment/drug is intended (Fig. 1). eranostics .... Using an anti-CD20 antibody as a delivery device to target the follicular ... systems combine diagnostic imaging (Ga-68-DOTATATE PET/CT) .... Intra-articular injected ...

  20. Modelling Recycling Targets

    DEFF Research Database (Denmark)

    hill, amanda; Leinikka Dall, Ole; Andersen, Frits Møller

    2014-01-01

    % for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...

  1. Strategic Targeted Advertising

    NARCIS (Netherlands)

    A. Galeotti; J.L. Moraga-Gonzalez (José Luis)

    2003-01-01

    textabstractWe present a strategic game of pricing and targeted-advertising. Firms can simultaneously target price advertisements to different groups of customers, or to the entire market. Pure strategy equilibria do not exist and thus market segmentation cannot occur surely. Equilibria exhibit

  2. Seedling root targets

    Science.gov (United States)

    Diane L. Haase

    2011-01-01

    Roots are critical to seedling performance after outplanting. Although root quality is not as quick and simple to measure as shoot quality, target root characteristics should be included in any seedling quality assessment program. This paper provides a brief review of root characteristics most commonly targeted for operational seedling production. These are: root mass...

  3. Internal targets for LEAR

    International Nuclear Information System (INIS)

    Kilian, K.; Gspann, J.; Mohl, D.; Poth, H.

    1984-01-01

    This chapter considers the use of thin internal targets in conjunction with phase-space cooling at the Low-Energy Antiproton Ring (LEAR). Topics considered include the merits of internal target operation; the most efficient use of antiprotons and of proton synchrotron (PS) protons, highest center-of-mass (c.m.) energy resolution; highest angular resolution and access to extreme angles; the transparent environment for all reaction products; a windowless source and pure targets; highest luminosity and count rates; access to lowest energies with increasing resolution; internal target thickness and vacuum requirements; required cooling performance; and modes of operation. It is demonstrated that an internal target in conjunction with phase-space cooling has the potential of better performance in terms of the economic use of antiprotons and consequently of PS protons; energy resolution; angular resolution; maximum reaction rate capability (statistical precision); efficient parasitic operation; transparency of the target for reaction products; access to low energies; and the ease of polarized target experiments. It is concluded that all p - experiments which need high statistics and high p - flux, such as studies of rare channels or broad, weak resonance structures, would profit from internal targets

  4. Fusion target design

    International Nuclear Information System (INIS)

    Bangerter, R.O.

    1978-01-01

    Most detailed fusion target design is done by numerical simulation using large computers. Although numerical simulation is briefly discussed, this lecture deals primarily with the way in which basic physical arguments, driver technology considerations and economical power production requirements are used to guide and augment the simulations. Physics topics discussed include target energetics, preheat, stability and symmetry. A specific design example is discussed

  5. Electron beam fusion targets

    International Nuclear Information System (INIS)

    Clauser, M.J.; Sweeney, M.A.

    1975-01-01

    R The behavior of the DT filled gold shells when irradiated by a variety of pulse shapes was studied. In these pulses the power (and beam current) was varied, but the voltage was kept constant at 1 MeV. In general the performance of the target, for a given peak power, was not significantly affected by the pulse shape. Pulses with rise times of up to half the implosion time do not significantly degrade the target performance. The use of the ''optimal pulse'' of laser fusion with a fixed peak power does not appear to improve the performance of these targets. The main function of the ''optimal pulse'' is to produce a large rho r of the target during the thermonuclear burn. In e-beam targets a total rho r of 5--10 g/cm 2 can be obtained without pulse shaping; the problem here is one of achieving high enough temperatures to ignite the DT. (U.S.)

  6. AA antiproton production target

    CERN Multimedia

    CERN PhotoLab

    1979-01-01

    The first version of the antiproton production target was a tungsten rod, 11 cm long and 3 mm in diameter. The rod was embedded in graphite, pressure-seated into an outer casing of stainless steel. At the entrance to the target assembly was a scintillator screen, imprinted with circles every 5 mm in radius, which allowed to precisely aim the 26 GeV high-intensity proton beam from the PS onto the centre of the target rod. The scintillator screen was a 1 mm thick plate of Cr-doped alumina. See also 7903034 and 7905091.

  7. Shiva target irradiation facility

    International Nuclear Information System (INIS)

    Manes, K.R.; Ahlstrom, H.G.; Coleman, L.W.; Storm, E.K.; Glaze, J.A.; Hurley, C.A.; Rienecker, F.; O'Neal, W.C.

    1977-01-01

    The first laser/plasma studies performed with the Shiva laser system will be two sided irradiations extending the data obtained by other LLL lasers to higher powers. The twenty approximately 1 TW laser pulses will reach the target simultaneously from above and below in nested pentagonal clusters. The upper and lower clusters of ten beams each are radially polarized so that they strike the target in p-polarization and maximize absorption. This geometry introduces laser system isolation problems which will be briefly discussed. The layout and types of target diagnostics will be described and a brief status report on the facility given

  8. STANFORD: Internal targets

    Energy Technology Data Exchange (ETDEWEB)

    Riordan, Michael

    1989-05-15

    Of burgeoning interest to many nuclear and particle physicists is a storage ring technique for fixed target experiments. It hinges on the use of gas-jet targets, shooting a narrow stream of atoms through a circulating beam of electrons or protons. Pioneered at CERN and the Soviet Novosibirsk Laboratory, more such 'internal targets' are being built or contemplated for storage rings in Europe, the Soviet Union, and the United States. From 9-12 January, physicists from around the world met at the Stanford Linear Accelerator Center (SLAC) to discuss prospects and problems in this expanding field.

  9. TARGET Research Goals

    Science.gov (United States)

    TARGET researchers use various sequencing and array-based methods to examine the genomes, transcriptomes, and for some diseases epigenomes of select childhood cancers. This “multi-omic” approach generates a comprehensive profile of molecular alterations for each cancer type. Alterations are changes in DNA or RNA, such as rearrangements in chromosome structure or variations in gene expression, respectively. Through computational analyses and assays to validate biological function, TARGET researchers predict which alterations disrupt the function of a gene or pathway and promote cancer growth, progression, and/or survival. Researchers identify candidate therapeutic targets and/or prognostic markers from the cancer-associated alterations.

  10. Structured cylindrical targets

    International Nuclear Information System (INIS)

    Arnold, R.

    1986-01-01

    A variety of experimental concepts using high-energy heavy-ion beams in cylindrical targets have been studied through numerical simulation. With an accelerator planned for GSl, plasma temperatures of 100 eV can be reached by cylindrical compression, using inhomogeneous hollow-shell targets. Magnetic insulation, using external fields, has been explored as an aid in reaching high core temperatures. Experiments on collision-pumped x-ray laser physics are also discussed. (ii) Two-dimensional PlC code simulations of homogeneous solid targets show hydrodynamic effects not found in previous 1-D calculations. (iii) Preliminary ideas for an experiment on non-equilibrium heavy-ion charge-states using an existing accelerator and a pre-formed plasma target are outlined. (author)

  11. Structured cylindrical targets

    International Nuclear Information System (INIS)

    Arnold, R.; Lackner-Russo, D.; Meyer-ter-Vehn, J.; Hoffmann, I.

    1986-01-01

    A variety of experimental concepts using high-energy heavy-ion beams in cylindrical targets have been studied through numerical simulation. With an accelerator planned for GSl, plasma temperatures of 100 eV can be reached by cylindrical compression, using inhomogenous hollow-shell targets. Magnetic insulation, using external fields, has been explored as an aid in reaching high core temperatures. Experiments on collision-pumped x-ray laser physics are also discussed. (ii) Two-dimensional PlC code simulations of homogeneous solid targets show hydrodynamic effects not found in previous l-D calculations. (iii) Preliminary ideas for an experiment on non-equilibrium heavy-ion charge-states using an existing accelerator and a pre-formed plasma target are outlined. (author)

  12. Target Price Accuracy

    Directory of Open Access Journals (Sweden)

    Alexander G. Kerl

    2011-04-01

    Full Text Available This study analyzes the accuracy of forecasted target prices within analysts’ reports. We compute a measure for target price forecast accuracy that evaluates the ability of analysts to exactly forecast the ex-ante (unknown 12-month stock price. Furthermore, we determine factors that explain this accuracy. Target price accuracy is negatively related to analyst-specific optimism and stock-specific risk (measured by volatility and price-to-book ratio. However, target price accuracy is positively related to the level of detail of each report, company size and the reputation of the investment bank. The potential conflicts of interests between an analyst and a covered company do not bias forecast accuracy.

  13. Autonomous Target Ranging Techniques

    DEFF Research Database (Denmark)

    Jørgensen, Peter Siegbjørn; Jørgensen, John Leif; Denver, Troelz

    2003-01-01

    of this telescope, a fast determination of the range to and the motion of the detected targets are important. This is needed in order to prepare the future observation strategy for each target, i.e. when is the closest approach where imaging will be optimal. In order to quickly obtain such a determination two...... ranging strategies are presented. One is an improved laser ranger with an effective range with non-cooperative targets of at least 10,000 km, demonstrated in ground tests. The accuracy of the laser ranging will be approximately 1 m. The laser ranger may furthermore be used for trajectory determination...... of nano-gravity probes, which will perform direct mass measurements of selected targets. The other is triangulation from two spacecraft. For this method it is important to distinguish between detection and tracking range, which will be different for Bering since different instruments are used...

  14. Targeted Cancer Therapies

    Science.gov (United States)

    ... are sometimes referred to as the product of "rational" drug design.) One approach to identify potential targets ... molecules that stimulate new blood vessel growth. Immunotherapies trigger the immune system to destroy cancer cells. Some ...

  15. Targeting radiation to tumours

    International Nuclear Information System (INIS)

    Wheldon, T.E.; Greater Glasgow Health Board, Glasgow

    1994-01-01

    Biologically targeted radiotherapy entails the preferential delivery of radiation to solid tumours or individual tumour cells by means of tumour-seeking delivery vehicles to which radionuclides can be conjugated. Monoclonal antibodies have attracted attention for some years as potentially selective targeting agents, but advances in tumour and molecular biology are now providing a much wider choice of molecular species. General radiobiological principles may be derived which are applicable to most forms of targeted radiotherapy. These principles provide guidelines for the appropriate choice of radionuclide in specific treatment situations and its optimal combination with other treatment modalities. In future, the availability of gene targeting agents will focus attention on the use of Auger electron emitters whose high potency and short range selectivity makes them attractive choices for specific killing of cancer cells whose genetic peculiarities are known. (author)

  16. Strategic Targeted Advertising

    OpenAIRE

    Andrea Galeotti; Jose Luis Moraga

    2003-01-01

    textabstractWe present a strategic game of pricing and targeted-advertising. Firms can simultaneously target price advertisements to different groups of customers, or to the entire market. Pure strategy equilibria do not exist and thus market segmentation cannot occur surely. Equilibria exhibit random advertising --to induce an unequal distribution of information in the market-- and random pricing --to obtain profits from badly informed buyers--. We characterize a positive profits equilibrium...

  17. Targets and teamwork

    DEFF Research Database (Denmark)

    Skinner, Timothy C.; Lange, Karin S.; Hoey, Hilary

    2017-01-01

    differences in mean HbA1c between centers ranging from 7.3±0.8% (53mmol/mol±8.7) to 8.9±1.1% (74mmol/mol±12.0). Centers with lower mean HbA1c had (1) parents who reported lower targets for their children, (2) health-care professionals that reported lower targets and more frequent testing, and (3) teams...

  18. Targets and special materials

    International Nuclear Information System (INIS)

    Blanc, R.; Bouriant, M.; Richaud, J.P.

    1997-01-01

    The target preparation group supplied a large number of samples to nuclear physicists for experiments using SARA and also other accelerators throughout the world. Particular preparation and projects include: 208 Pb, 116 Cd, 6 LiF, 123 Sb, In and Ta targets, strippers for SARA and GANIL, optical silicone disks for POLDER and GRAAL experiments, active participations for the AMS project and finally filament preparation for the GENEPI project. (authors)

  19. The ISIS target

    International Nuclear Information System (INIS)

    Carne, A.; Broome, T.A.; Hogston, J.R.; Holding, M.

    1989-01-01

    This presentation discusses the two target failures that have occurred, gives the understanding of the causes and indicates the steps being taken to alleviate the problems. At the outset of the design it was understood that the target would have a finite lifetime, due to radiation damage effects, exacerbated by mechanical damage due to thermal cycling and fatigue. Estimates of target lifetime at full intensity are about 2 years for radiation damage swelling and about 10E4 gross thermal excursions. The latter number is the one which gives uncertainty in defining the life of the target, since it is dependent on the reliability of the accelerator and quality of the proton beam. The commissioning of an accelerator system and bringing it up to high beam intensities have their own special problems. There must be protection of components against uncontrolled beam loss, which produces thermal damage, prompt radiation and induced activity. Fast beam trips for beam loss protection, or equipment failures, result in quenches from high temperature in the target which get bigger with increasing beam intensity. But the target itself is a difficult device to make, taking about 12 months to manufacture. Further, changing one is a complex and time consuming task, not without its hazards. There is thus something of a balancing act to bring the accelerator towards specification before the target fails due to thermal cycling fatigue. In the early days of ISIS beam loss protection was the dominant consideration and the target was regarded somewhat as a sacrificial lamb to the goddess of machine reliability. 2 refs., 6 figs

  20. An ISOLDE target unit

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    A good dozen different targets are available for ISOLDE, made of different materials and equipped with different kinds of ion-sources, according to the needs of the experiments. Each separator (GPS: general purpose; HRS: high resolution) has its own target. Because of the high radiation levels, robots effect the target changes, about 80 times per year. In the standard unit shown in picture _01, the target is the cylindrical object in the front. It contains uranium-carbide kept at a temperature of 2200 deg C, necessary for the isotopes to be able to escape. At either end, one sees the heater current leads, carrying 700 A. The Booster beam, some 3E13 protons per pulse, enters the target from left. The evaporated isotope atoms enter a hot-plasma ion source (the black object behind the target). The whole unit sits at 60 kV potential (pulsed in synchronism with the arrival of the Booster beam) which accelerates the ions (away from the viewer) towards one of the 2 separators.

  1. Laser targets: introduction

    International Nuclear Information System (INIS)

    Rosen, M.D.

    1985-01-01

    The laser target design group was engaged in three main tasks in 1984: (1) analyzing Novette implosion and hohlraum-scaling data, (2) planning for the first experiments on Nova, and (3) designing laboratory x-ray laser targets and experiments. The Novette implosion and hohlraum scaling data are mostly classified and are therefore not discussed in detail here. The authors achieved average final/initial pusher pr ratios of about 50, some 3 times higher than the value achieved in the best Shiva shots. These pr values imply a fuel compression to 100 times liquid density, although this figure and other aspects of the experiments are subject to further interpretation because of detailed questions of target symmetry and stability. Their main long-term goal for Nova is to produce a so-called hydrodynamically equivalent target (HET) - that is, a target whose hydrodynamic behavior (implosion velocity, convergence ratio, symmetry and stability requirements, etc.) is very much like that of a high-gain target, but one that is scaled down in size to match the energy available from Nova and is too small to achieve enough hot-spot pr to ignite the cold, near-Fermi-degenerate fuel around it. Their goal for Nova's first year is to do experiments that will teach them how to achieve the symmetry and stability conditions required by an HET

  2. Argus target chamber

    International Nuclear Information System (INIS)

    Rienecker, F. Jr.; Glaros, S.S.; Kobierecki, M.

    1975-01-01

    A target chamber for application in the laser fusion program must satisfy some very basic requirements. (1) Provide a vacuum on the order of 10 -6 torr. (2) Support a microscopically small target in a fixed point in space and verify its location within 5 micrometers. (3) Contain an adjustable beam focusing system capable of delivering a number of laser beams onto the target simultaneously, both in time and space. (4) Provide access for diagnostics to evaluate the results of target irradiation. (5) Have flexibility to allow changes in targets, focusing optics and number of beams. The ARGUS laser which is now under construction at LLL will have a target chamber which meets these requirements in a simple economic manner. The chamber and auxiliary equipment are described, with reference to two double beam focusing systems; namely, lenses and ellipsoidal mirrors. Provision is made for future operation with four beams, using ellipsoidal mirrors for two-sided illumination and lens systems for tetragonal and tetrahedral irradiation

  3. The mechanical design and fabrication of 162.5 MHz buncher for China accelerator driven sub-critical system injector II

    Energy Technology Data Exchange (ETDEWEB)

    Niu, Hai Hua; Li, Youtang [Lanzhou University of Technology, Lanzhou (China); He, Yuan; Zhang, Bin; Huang, Shichun; Yuan, Chenzhang; Jia, Huan; Zhang, Shenghu [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou (China)

    2017-08-15

    A buncher is one of the main pieces of equipment in the medium energy beam transport line (MEBT) for China accelerator driven sub-critical system (C-ADS) Injector II. To focus the beam longitudinally and match the beam for the acceptance of the superconducting linac section, two room temperature quarter wave resonator (QWR) bunchers with frequency of 162.5 MHz have been designed as parts of the MEBT. According to the beam transmission matching of the MEBT and the geometric parameters requirements of bunchers, the unique mechanical structure and the main processing technology of buncher cavities and their couplers and tuners are described in this paper. The fabrication of bunchers and their parts have been completed and tested at high power, the test results agree well with the design requirements. These bunchers work well for about two years in Institute of Modern Physics, Chinese Academy of Sciences.

  4. The mechanical design and fabrication of 162.5 MHz buncher for China accelerator driven sub-critical system injector II

    Directory of Open Access Journals (Sweden)

    Haihua Niu

    2017-08-01

    Full Text Available A buncher is one of the main pieces of equipment in the medium energy beam transport line (MEBT for China accelerator driven sub-critical system (C-ADS Injector II. To focus the beam longitudinally and match the beam for the acceptance of the superconducting linac section, two room temperature quarter wave resonator (QWR bunchers with frequency of 162.5 MHz have been designed as parts of the MEBT. According to the beam transmission matching of the MEBT and the geometric parameters requirements of bunchers, the unique mechanical structure and the main processing technology of buncher cavities and their couplers and tuners are described in this paper. The fabrication of bunchers and their parts have been completed and tested at high power, the test results agree well with the design requirements. These bunchers work well for about two years in Institute of Modern Physics, Chinese Academy of Sciences.

  5. MiniCD4 microbicide prevents HIV infection of human mucosal explants and vaginal transmission of SHIV(162P3 in cynomolgus macaques.

    Directory of Open Access Journals (Sweden)

    Nathalie Dereuddre-Bosquet

    Full Text Available In complement to an effective vaccine, development of potent anti-HIV microbicides remains an important priority. We have previously shown that the miniCD4 M48U1, a functional mimetic of sCD4 presented on a 27 amino-acid stable scaffold, inhibits a broad range of HIV-1 isolates at sub-nanomolar concentrations in cellular models. Here, we report that M48U1 inhibits efficiently HIV-1(Ba-L in human mucosal explants of cervical and colorectal tissues. In vivo efficacy of M48U1 was evaluated in nonhuman primate (NHP model of mucosal challenge with SHIV(162P3 after assessing pharmacokinetics and pharmacodynamics of a miniCD4 gel formulation in sexually matured female cynomolgus macaques. Among 12 females, half were treated with hydroxyethylcellulose-based gel (control, the other half received the same gel containing 3 mg/g of M48U1, one hour before vaginal route challenge with 10 AID(50 of SHIV(162P3. All control animals were infected with a peak plasma viral load of 10(5-10(6 viral RNA (vRNA copies per mL. In animals treated with miniCD4, 5 out of 6 were fully protected from acquisition of infection, as assessed by qRT-PCR for vRNA detection in plasma, qPCR for viral DNA detection in PBMC and lymph node cells. The only infected animal in this group had a delayed peak of viremia of one week. These results demonstrate that M48U1 miniCD4 acts in vivo as a potent entry inhibitor, which may be considered in microbicide developments.

  6. Burglar Target Selection

    Science.gov (United States)

    Townsley, Michael; Bernasco, Wim; Ruiter, Stijn; Johnson, Shane D.; White, Gentry; Baum, Scott

    2015-01-01

    Objectives: This study builds on research undertaken by Bernasco and Nieuwbeerta and explores the generalizability of a theoretically derived offender target selection model in three cross-national study regions. Methods: Taking a discrete spatial choice approach, we estimate the impact of both environment- and offender-level factors on residential burglary placement in the Netherlands, the United Kingdom, and Australia. Combining cleared burglary data from all study regions in a single statistical model, we make statistical comparisons between environments. Results: In all three study regions, the likelihood an offender selects an area for burglary is positively influenced by proximity to their home, the proportion of easily accessible targets, and the total number of targets available. Furthermore, in two of the three study regions, juvenile offenders under the legal driving age are significantly more influenced by target proximity than adult offenders. Post hoc tests indicate the magnitudes of these impacts vary significantly between study regions. Conclusions: While burglary target selection strategies are consistent with opportunity-based explanations of offending, the impact of environmental context is significant. As such, the approach undertaken in combining observations from multiple study regions may aid criminology scholars in assessing the generalizability of observed findings across multiple environments. PMID:25866418

  7. LANSCE target system performance

    International Nuclear Information System (INIS)

    Russell, G.J.; Gilmore, J.S.; Robinson, H.; Legate, G.L.; Bridge, A.; Sanchez, R.J.; Brewton, R.J.; Woods, R.; Hughes, H.G. III

    1989-01-01

    We measured neutron beam fluxes at LANSCE using gold foil activation techniques. We did an extensive computer simulation of the as-built LANSCE Target/Moderator/Reflector/Shield geometry. We used this mockup in a Monte Carlo calculation to predict LANSCE neutronic performance for comparison with measured results. For neutron beam fluxes at 1 eV, the ratio of measured data to calculated varies from ∼0.6-0.9. The computed 1 eV neutron leakage at the moderator surface is 3.9 x 10 10 n/eV-sr-s-μA for LANSCE high-intensity water moderators. The corresponding values for the LANSCE high-resolution water moderator and the liquid hydrogen moderator are 3.3 and 2.9 x 10 10 , respectively. LANSCE predicted moderator intensities (per proton) for a tungsten target are essentially the same as ISIS predicted moderator intensities for a depleted uranium target. The calculated LANSCE steady state unperturbed thermal (E 13 n/cm 2 -s. The unique LANSCE split-target/flux-trap-moderator system is performing exceedingly well. The system has operated without a target or moderator change for over three years at nominal proton currents of ∼25 μA of 800-MeV protons. (author)

  8. Modelling Recycling Targets

    DEFF Research Database (Denmark)

    Hill, Amanda Louise; Leinikka Dall, Ole; Andersen, Frits M.

    2014-01-01

    Within the European Union (EU) a paradigm shift is currently occurring in the waste sector, where EU waste directives and national waste strategies are placing emphasis on resource efficiency and recycling targets. The most recent Danish resource strategy calculates a national recycling rate of 22......% for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...... the existing technological, organizational and legislative frameworks may affect recycling activities. The results of the analysis show that with current best practice recycling rates, the 50% recycling rate cannot be reached without recycling of household biowaste. It also shows that all Danish municipalities...

  9. Targeted Phototherapy (newer phototherapy

    Directory of Open Access Journals (Sweden)

    Zonunsanga

    2015-04-01

    Full Text Available Conventional phototherapy uses a whole body cabinet or body part machine such as hand, foot or scalp machines. They have many disadvantages due to which new phototherapy technique was then developed to overcome this situation. This new technique is called targeted phototherapy which includes excimer laser, intense pulse light system (IPL, photodynamic therapy and ultraviolet (UV light source with a sophisticated delivery system which is easy to be operated by hands. The mechanisms of action of targeted phototherapy systems are similar to those in conventional UVB/UVA therapy. They have many advantages like less chances of side effects, avoidance of exposure of unnecessary sites, faster response, shortening of the duration of treatments. But they have disadvantages like high costs and inability to use for extensive areas. This review article discusses targeted phototherapy in considerable to the mechanism of actions and advantages and disadvantages in comparison to the conventional phototherapy.

  10. Setting reference targets

    International Nuclear Information System (INIS)

    Ruland, R.E.

    1997-04-01

    Reference Targets are used to represent virtual quantities like the magnetic axis of a magnet or the definition of a coordinate system. To explain the function of reference targets in the sequence of the alignment process, this paper will first briefly discuss the geometry of the trajectory design space and of the surveying space, then continue with an overview of a typical alignment process. This is followed by a discussion on magnet fiducialization. While the magnetic measurement methods to determine the magnetic centerline are only listed (they will be discussed in detail in a subsequent talk), emphasis is given to the optical/mechanical methods and to the task of transferring the centerline position to reference targets

  11. Fine target of deuterium

    International Nuclear Information System (INIS)

    Diaz Diaz, J.; Granados Gonzalez, C. E.; Gutierrez Bernal, R.

    1959-01-01

    A fine target of deuterium on a tantalum plate by the absorption method is obtained. In order to obtain the de gasification temperature an induction generator of high frequency is used and the deuterium pass is regulated by means of a palladium valve. Two vacuum measures are available, one to measure the high vacuum in the de gasification process of the tantalum plate and the other, for low vacuum, to measure the deuterium inlet in the installation and the deuterium pressure change in the installation after the absorption in the tantalum plate. A target of 48 μ gr/cm 2 thick is obtained. (Author) 1 refs

  12. Targeting the right journal.

    Science.gov (United States)

    Piterman, L; McCall, L

    1999-07-01

    While research is scientific, publication is a mixture of science and political pragmatism. Targeting the right journal is influenced by the following factors: the discipline that best represents the subject; the purpose of the message; the audience who are to be recipients of the message; the realities of geographic parochialism; the desire of authors to maximise personal and professional opportunities. If the originally targeted journal rejects the article, authors should have alternative publication strategies that give them professional recognition without requiring them to compromise the message or their ethics.

  13. AA antiproton production target

    CERN Multimedia

    CERN PhotoLab

    1979-01-01

    The first version of the antiproton production target was a tungsten rod, 11 cm long (actually a row of 11 rods, each 1 cm long) and 3 mm in diameter. The rod was embedded in graphite, pressure-seated into an outer casing made of stainless steel. The casing had fins for forced-air cooling. In this picture, the 26 GeV high-intensity beam from the PS enters from the right, where a scintillator screen, with circles every 5 mm in radius, permits precise aim at the target centre. See also 7903034 and 7905094.

  14. Targets and tactics

    DEFF Research Database (Denmark)

    Woo, V; Shestakova, M V; Ørskov, C

    2008-01-01

    BACKGROUND: The incidence of type 2 diabetes is reaching pandemic proportions, impacting patients and healthcare systems across the globe. Evidence suggests that a majority of patients are not achieving recommended blood glucose targets resulting in an increased risk of micro- and macro-vascular ......BACKGROUND: The incidence of type 2 diabetes is reaching pandemic proportions, impacting patients and healthcare systems across the globe. Evidence suggests that a majority of patients are not achieving recommended blood glucose targets resulting in an increased risk of micro- and macro...... diabetes has never been more compelling; with a clear focus on strategies for glycaemic control, the impact of the diabetes pandemic can be limited....

  15. Optimal exploration target zones

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2008-09-01

    Full Text Available -of-evidence (WofE) method logistic regression canonical favorability analysis neural networks evidential belief functions Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study... for the following equation: n∑ i=r ( n i ) pi(1− p)n−i = 0.95 . (1) Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study Methodology Results METHODS (cont. . . ): FITNESS FUNCTION...

  16. ISOLDE back on target

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    Today, Friday 1 August, the ISOLDE installation, supplied by the beams of the PS Booster, restarted its physics programme. After a shutdown of almost a year and a half, there was a real buzz in the air as the first beam of protons hit the target of the first post-LS1 ISOLDE experiment.   One of the new target-handling robots installed by ISOLDE during LS1. Many improvements have been made to the ISOLDE installation during LS1. One of the main projects was the installation of new robots for handling the targets (see photo 1). “Our targets are bombarded by protons from the PS Booster’s beams and become very radioactive,” explains Maria Jose Garcia Borge, spokesperson for the ISOLDE collaboration. “They therefore need to be handled carefully, which is where the robots come in. The robots we had until now were already over 20 years old and were starting to suffer from the effects of radiation. So LS1 was a perfect opportunity to replace them with more moder...

  17. Targeted Therapy for Melanoma

    International Nuclear Information System (INIS)

    Quinn, Thomas; Moore, Herbert

    2016-01-01

    The research project, entitled ''Targeted Therapy for Melanoma,'' was focused on investigating the use of kidney protection measures to lower the non-specific kidney uptake of the radiolabeled Pb-DOTA-ReCCMSH peptide. Previous published work demonstrated that the kidney exhibited the highest non-target tissue uptake of the "2"1"2"P"b"/"2"0"3Pb radiolabeled melanoma targeting peptide DOTA-ReCCMSH. The radiolabeled alpha-melanocyte stimulating hormone (α-MSH) peptide analog DOTA-Re(Arg"1"1)CCMSH, which binds the melanocortin-1 receptor over-expressed on melanoma tumor cells, has shown promise as a PRRT agent in pre-clinical studies. High tumor uptake of "2"1"2Pb labeled DOTA-Re(Arg"1"1)CCMSH resulted in tumor reduction or eradication in melanoma therapy studies. Of particular note was the 20-50% cure rate observed when melanoma mice were treated with alpha particle emitter "2"1"2Pb. However, as with most PRRT agents, high radiation doses to the kidneys where observed. To optimize tumor treatment efficacy and reduce nephrotoxicity, the tumor to kidney uptake ratio must be improved. Strategies to reduce kidney retention of the radiolabeled peptide, while not effecting tumor uptake and retention, can be broken into several categories including modification of the targeting peptide sequence and reducing proximal tubule reabsorption.

  18. Targets of curcumin

    Science.gov (United States)

    Zhou, Hongyu; Beevers, Christopher S.; Huang, Shile

    2010-01-01

    Curcumin (diferuloylmethane), an orange-yellow component of turmeric or curry powder, is a polyphenol natural product isolated from the rhizome of the plant Curcuma longa. For centuries, curcumin has been used in some medicinal preparation or used as a food-coloring agent. In recent years, extensive in vitro and in vivo studies suggested curcumin has anticancer, antiviral, antiarthritic, anti-amyloid, antioxidant, and anti-inflammatory properties. The underlying mechanisms of these effects are diverse and appear to involve the regulation of various molecular targets, including transcription factors (such as nuclear factor-κB), growth factors (such as vascular endothelial cell growth factor), inflammatory cytokines (such as tumor necrosis factor, interleukin 1 and interleukin 6), protein kinases (such as mammalian target of rapamycin, mitogen-activated protein kinases, and Akt) and other enzymes (such as cyclooxygenase 2 and 5 lipoxygenase). Thus, due to its efficacy and regulation of multiple targets, as well as its safety for human use, curcumin has received considerable interest as a potential therapeutic agent for the prevention and/or treatment of various malignant diseases, arthritis, allergies, Alzheimer’s disease, and other inflammatory illnesses. This review summarizes various in vitro and in vivo pharmacological aspects of curcumin as well as the underlying action mechanisms. The recently identified molecular targets and signaling pathways modulated by curcumin are also discussed here. PMID:20955148

  19. Target-Rich Environment

    Science.gov (United States)

    Perna, Mark C.

    2005-01-01

    Target marketing is defining school enrollment goals and then developing a strategic plan to accomplish those goals through the use of specific communication vehicles and community focus. It is critical to reach the right audience, with the right message, at the right time, for the right cost. In this brief article, the author describes several…

  20. Targeted enzyme prodrug therapies.

    Science.gov (United States)

    Schellmann, N; Deckert, P M; Bachran, D; Fuchs, H; Bachran, C

    2010-09-01

    The cure of cancer is still a formidable challenge in medical science. Long-known modalities including surgery, chemotherapy and radiotherapy are successful in a number of cases; however, invasive, metastasized and inaccessible tumors still pose an unresolved and ongoing problem. Targeted therapies designed to locate, detect and specifically kill tumor cells have been developed in the past three decades as an alternative to treat troublesome cancers. Most of these therapies are either based on antibody-dependent cellular cytotoxicity, targeted delivery of cytotoxic drugs or tumor site-specific activation of prodrugs. The latter is a two-step procedure. In the first step, a selected enzyme is accumulated in the tumor by guiding the enzyme or its gene to the neoplastic cells. In the second step, a harmless prodrug is applied and specifically converted by this enzyme into a cytotoxic drug only at the tumor site. A number of targeting systems, enzymes and prodrugs were investigated and improved since the concept was first envisioned in 1974. This review presents a concise overview on the history and latest developments in targeted therapies for cancer treatment. We cover the relevant technologies such as antibody-directed enzyme prodrug therapy (ADEPT), gene-directed enzyme prodrug therapy (GDEPT) as well as related therapies such as clostridial- (CDEPT) and polymer-directed enzyme prodrug therapy (PDEPT) with emphasis on prodrug-converting enzymes, prodrugs and drugs.

  1. Targeting trichothecene biosynthetic genes

    NARCIS (Netherlands)

    Wei, Songhong; Lee, van der Theo; Verstappen, Els; Gent, van Marga; Waalwijk, Cees

    2017-01-01

    Biosynthesis of trichothecenes requires the involvement of at least 15 genes, most of which have been targeted for PCR. Qualitative PCRs are used to assign chemotypes to individual isolates, e.g., the capacity to produce type A and/or type B trichothecenes. Many regions in the core cluster

  2. Targeted Therapy for Melanoma

    Energy Technology Data Exchange (ETDEWEB)

    Quinn, Thomas [Alphamed, Jackson, TN (United States); Moore, Herbert [Alphamed, Jackson, TN (United States)

    2016-12-05

    The research project, entitled ”Targeted Therapy for Melanoma,” was focused on investigating the use of kidney protection measures to lower the non-specific kidney uptake of the radiolabeled Pb-DOTA-ReCCMSH peptide. Previous published work demonstrated that the kidney exhibited the highest non-target tissue uptake of the 212Pb/203Pb radiolabeled melanoma targeting peptide DOTA-ReCCMSH. The radiolabeled alpha-melanocyte stimulating hormone (α-MSH) peptide analog DOTA-Re(Arg11)CCMSH, which binds the melanocortin-1 receptor over-expressed on melanoma tumor cells, has shown promise as a PRRT agent in pre-clinical studies. High tumor uptake of 212Pb labeled DOTA-Re(Arg11)CCMSH resulted in tumor reduction or eradication in melanoma therapy studies. Of particular note was the 20-50% cure rate observed when melanoma mice were treated with alpha particle emitter 212Pb. However, as with most PRRT agents, high radiation doses to the kidneys where observed. To optimize tumor treatment efficacy and reduce nephrotoxicity, the tumor to kidney uptake ratio must be improved. Strategies to reduce kidney retention of the radiolabeled peptide, while not effecting tumor uptake and retention, can be broken into several categories including modification of the targeting peptide sequence and reducing proximal tubule reabsorption.

  3. The targets of curcumin.

    Science.gov (United States)

    Zhou, Hongyu; Beevers, Christopher S; Huang, Shile

    2011-03-01

    Curcumin (diferuloylmethane), an orange-yellow component of turmeric or curry powder, is a polyphenol natural product isolated from the rhizome of the plant Curcuma longa. For centuries, curcumin has been used in some medicinal preparation or used as a food-coloring agent. In recent years, extensive in vitro and in vivo studies suggested curcumin has anticancer, antiviral, antiarthritic, anti-amyloid, antioxidant, and anti-inflammatory properties. The underlying mechanisms of these effects are diverse and appear to involve the regulation of various molecular targets, including transcription factors (such as nuclear factor-kB), growth factors (such as vascular endothelial cell growth factor), inflammatory cytokines (such as tumor necrosis factor, interleukin 1 and interleukin 6), protein kinases (such as mammalian target of rapamycin, mitogen-activated protein kinases, and Akt) and other enzymes (such as cyclooxygenase 2 and 5 lipoxygenase). Thus, due to its efficacy and regulation of multiple targets, as well as its safety for human use, curcumin has received considerable interest as a potential therapeutic agent for the prevention and/or treatment of various malignant diseases, arthritis, allergies, Alzheimer's disease, and other inflammatory illnesses. This review summarizes various in vitro and in vivo pharmacological aspects of curcumin as well as the underlying action mechanisms. The recently identified molecular targets and signaling pathways modulated by curcumin are also discussed here.

  4. SU-F-J-162: Is Bulky Electron Density Assignment Appropriatefor MRI-Only Based Treatment Planning for Lung Cancer?

    Energy Technology Data Exchange (ETDEWEB)

    Prior, P; Chen, X; Johnstone, C; Gore, E; Li, X [Medical College of Wisconsin, Milwaukee, WI (United States)

    2016-06-15

    Purpose: To assess the appropriateness of bulky electron density assisment for MRI-only treatment planning for lung cancer via comparing dosimetric difference between MRI- and CT-based plans. Methods: Planning 4DCTs acquired for six representative lung cancer patients were used to generate CT-based IMRT plans. To avoid the effect of anatomic difference between CT and MRI, MRI-based plans were generated using CTs by forcing the relative electron density (rED) of organ specific values from ICRU report 46 and using the mean rED value of the internal target volume (ITV) of the patient for the ITV. Both CT and “MRI” plans were generated using a research planning system (Monaco, Elekta) employing Monte Carlo dose calculation the following dose-volume-parameters (DVPs): D99 – dose delivered to 99% of the ITV/PTV volume; D95; D5; D1; Vpd –volume receiving the prescription dose; V5 – volume of normal lung irradiated > 5 Gy; and V20. The percent point difference and dose difference was used for comparison for Vpd-V5-V20 and D99-D1, respectively. Four additional plans per patient were calculated with rEDITV = 0.6 and 1.0 and rEDlung = 0.1 and 0.5. Results: Noticeable differences in the ITV and PTV point doses and DVPs were observed. Variations in Vpd ranged from 0.0–6.4% and 0.32–18.3% for the ITV and PTV, respectively. The ITV and PTV variations in D99, D95, D5 and D1 were 0.15–3.2 Gy. The normal lung V5 & V20 variations were no larger than 1.9%. In some instances, varying the rEDITV between rEDmean, 0.6 and 1.0 resulted in D95 increases ranging from 3.9–6.3%. Uniform rED assignment on normal lung affected DVPs of ITV and PTV by 4.0–9.8% and 0.3–19.6%, respectively. Conclusion: The commonly-used uniform rED assignment in MRI-only based planning may not be appropriate for lung-cancer. A voxel based method, e.g. synthetic CT generated from MRI data, is required. This work was partially funded by Elekta, Inc.

  5. Parameter measurement of target

    International Nuclear Information System (INIS)

    Gao Dangzhong

    2001-01-01

    The progress of parameter measurement of target (ICF-15) in 1999 are presented, including the design and contract of the microsphere equator profiler, the precise air bearing manufacturing, high-resolution X-ray image of multi-layer shells and the X-ray photos processed with special image and data software, some plastic shells measured in precision of 0.3 μm, the high-resolution observation and photograph system of 'dew-point method', special fixture of target and its temperature distribution measuring, the dew-point temperature and fuel gas pressure of shells measuring with internal pressure of 5 - 15 (x10 5 ) Pa D 2 and wall thickness of 1.5∼3 μm

  6. Guilty Feelings, Targeted Actions

    Science.gov (United States)

    Cryder, Cynthia E.; Springer, Stephen; Morewedge, Carey K.

    2014-01-01

    Early investigations of guilt cast it as an emotion that prompts broad reparative behaviors that help guilty individuals feel better about themselves or about their transgressions. The current investigation found support for a more recent representation of guilt as an emotion designed to identify and correct specific social offenses. Across five experiments, guilt influenced behavior in a targeted and strategic way. Guilt prompted participants to share resources more generously with others, but only did so when those others were persons whom the participant had wronged and only when those wronged individuals could notice the gesture. Rather than trigger broad reparative behaviors that remediate one’s general reputation or self-perception, guilt triggers targeted behaviors intended to remediate specific social transgressions. PMID:22337764

  7. Inertial confinement fusion target

    International Nuclear Information System (INIS)

    Bourdier, A.

    2001-12-01

    A simple, zero-dimensional model describing the temporal behaviour of an imploding-shell, magnetized fuel inertial confinement fusion target is formulated. The addition of a magnetic field to the fuel reduces thermal conduction losses. As a consequence, it might lead to high gains and reduce the driver requirements. This beneficial effect of the magnetic field on thermonuclear gains is confirmed qualitatively by the zero-dimensional model results. Still, the extent of the initial-condition space for which significant gains can occur is not, by far, as large as previously reported. One-dimensional CEA code simulations which confirm this results are also presented. Finally, we suggest to study the approach proposed by Hasegawa. In this scheme, the laser target is not imploded, and the life-time of the plasma can be very much increased. (author)

  8. Hohlraum targets for HIDIF

    International Nuclear Information System (INIS)

    Ramis, R.; Ramirez, J.; Meyer-ter-Vehn, J.

    2000-01-01

    An optimized high gain IFE indirect target design is presented. Beam parameters (5 MJ of 5 GeV Bi + ions in 10-20 ns and focal spot of 3 mm radius) are in agreement to the ones considered recently for the European Study Group on Heavy Ion Driven Inertial Fusion (HIDIF). The energy yield is close to 530 MJ, giving a large enough gain appropriate for industrial energy production. Numerical and analytical modeling are described and discussed. (authors)

  9. Target Glint Suppression Technology.

    Science.gov (United States)

    1980-09-01

    Rayleigh for either horizontal or vertical polarization). 2.1.2 Spatial Characterization. Before the effects of diversity on target detection can be...ncs) dRCS T If the lower intergration limit is taken as zero for the Rayleigh targct model of interest, then this quantity is unbounded. In...port wing, inner section Trailing edge of starboard .:ing, inner section Leading edge of horizontal stabilizer, inner section, port side TLeal, -g

  10. Conditional targeting for communication

    International Nuclear Information System (INIS)

    Rodrigues, Anselmo; Caldas, Ibere L.; Baptista, Murilo S.; Piqueira, Jose Roberto C.

    2004-01-01

    In this work we propose the use of a targeting method applied to chaotic systems in order to reach special trajectories that encode arbitrary sources of messages. One advantage of this procedure is to overcome dynamical constraints which impose limits in the amount of information that the chaotic trajectories can encode. Another advantage is the message decoding, practically instantaneous and independent of any special technique or algorithm. Furthermore, with this procedure, information can be transmitted with no errors due to bounded noise

  11. Heterogeneous chromatin target model

    International Nuclear Information System (INIS)

    Watanabe, Makoto

    1996-01-01

    The higher order structure of the entangled chromatin fibers in a chromosome plays a key role in molecular control mechanism involved in chromosome mutation due to ionizing radiations or chemical mutagens. The condensed superstructure of chromatin is not so rigid and regular as has been postulated in general. We have proposed a rheological explanation for the flexible network system ('chromatin network') that consists of the fluctuating assembly of nucleosome clusters linked with supertwisting DNA in a chromatin fiber ('Supertwisting Particulate Model'). We have proposed a 'Heterosensitive Target Model' for cellular radiosensitivity that is a modification of 'Heterogeneous Target Model'. The heterogeneity of chromatin target is derived from the highly condensed organization of chromatin segments consist of unstable and fragile sites in the fluctuating assembly of nucleosome clusters, namely 'supranucleosomal particles' or 'superbeads'. The models have been principally supported by our electron microscopic experiments employing 'surface - spreading whole - mount technique' since 1967. However, some deformation and artifacts in the chromatin structure are inevitable with these electron microscopic procedures. On the contrary, the 'atomic force microscope (AFM)' can be operated in liquid as well as in the air. A living specimen can be examined without any preparative procedures. Micromanipulation of the isolated chromosome is also possible by the precise positional control of a cantilever on the nanometer scale. The living human chromosomes were submerged in a solution of culture medium and observed by AFM using a liquid immersion cell. The surface - spreading whole - mount technique was applicable for this observation. The particulate chromatin segments of nucleosome clusters were clearly observed within mitotic human chromosomes in a living hydrated condition. These findings support the heterogeneity of chromatin target in a living cell. (J.P.N.)

  12. Implementing Target Value Design.

    Science.gov (United States)

    Alves, Thais da C L; Lichtig, Will; Rybkowski, Zofia K

    2017-04-01

    An alternative to the traditional way of designing projects is the process of target value design (TVD), which takes different departure points to start the design process. The TVD process starts with the client defining an allowable cost that needs to be met by the design and construction teams. An expected cost in the TVD process is defined through multiple interactions between multiple stakeholders who define wishes and others who define ways of achieving these wishes. Finally, a target cost is defined based on the expected profit the design and construction teams are expecting to make. TVD follows a series of continuous improvement efforts aimed at reaching the desired goals for the project and its associated target value cost. The process takes advantage of rapid cycles of suggestions, analyses, and implementation that starts with the definition of value for the client. In the traditional design process, the goal is to identify user preferences and find solutions that meet the needs of the client's expressed preferences. In the lean design process, the goal is to educate users about their values and advocate for a better facility over the long run; this way owners can help contractors and designers to identify better solutions. This article aims to inform the healthcare community about tools and techniques commonly used during the TVD process and how they can be used to educate and support project participants in developing better solutions to meet their needs now as well as in the future.

  13. The Bochum Polarized Target

    International Nuclear Information System (INIS)

    Reicherz, G.; Goertz, S.; Harmsen, J.; Heckmann, J.; Meier, A.; Meyer, W.; Radtke, E.

    2001-01-01

    The Bochum 'Polarized Target' group develops the target material 6 LiD for the COMPASS experiment at CERN. Several different materials like alcohols, alcanes and ammonia are under investigation. Solid State Targets are polarized in magnetic fields higher than B=2.5T and at temperatures below T=1K. For the Dynamic Nuclear Polarization process, paramagnetic centers are induced chemically or by irradiation with ionizing beams. The radical density is a critical factor for optimization of polarization and relaxation times at adequate magnetic fields and temperatures. In a high sensitive EPR--apparatus, an evaporator and a dilution cryostat with a continuous wave NMR--system, the materials are investigated and optimized. To improve the polarization measurement, the Liverpool NMR-box is modified by exchanging the fixed capacitor for a varicap diode which not only makes the tuning very easy but also provides a continuously tuned circuit. The dependence of the signal area upon the circuit current is measured and it is shown that it follows a linear function

  14. Inflation targeting and core inflation

    OpenAIRE

    Julie Smith

    2005-01-01

    This paper examines the interaction of core inflation and inflation targeting as a monetary policy regime. Interest in core inflation has grown because of inflation targeting. Core inflation is defined in numerous ways giving rise to many potential measures; this paper defines core inflation as the best forecaster of inflation. A cross-country study finds before the start of inflation targeting, but not after, core inflation differs between non-inflation targeters and inflation targeters. Thr...

  15. Silicon Nitride Deposition for Flexible Organic Electronic Devices by VHF (162 MHz)-PECVD Using a Multi-Tile Push-Pull Plasma Source.

    Science.gov (United States)

    Kim, Ki Seok; Kim, Ki Hyun; Ji, You Jin; Park, Jin Woo; Shin, Jae Hee; Ellingboe, Albert Rogers; Yeom, Geun Young

    2017-10-19

    Depositing a barrier film for moisture protection without damage at a low temperature is one of the most important steps for organic-based electronic devices. In this study, the authors investigated depositing thin, high-quality SiN x film on organic-based electronic devices, specifically, very high-frequency (162 MHz) plasma-enhanced chemical vapor deposition (VHF-PECVD) using a multi-tile push-pull plasma source with a gas mixture of NH 3 /SiH 4 at a low temperature of 80 °C. The thin deposited SiN x film exhibited excellent properties in the stoichiometry, chemical bonding, stress, and step coverage. Thin film quality and plasma damage were investigated by the water vapor transmission rate (WVTR) and by electrical characteristics of organic light-emitting diode (OLED) devices deposited with SiN x , respectively. The thin deposited SiN x film exhibited a low WVTR of 4.39 × 10 -4  g (m 2 · day) -1 for a single thin (430 nm thick) film SiN x and the electrical characteristics of OLED devices before and after the thin SiN x film deposition on the devices did not change, which indicated no electrical damage during the deposition of SiN x on the OLED device.

  16. Socio-economic development and emotion-health connection revisited: a multilevel modeling analysis using data from 162 counties in China.

    Science.gov (United States)

    Yu, Zonghuo; Wang, Fei

    2016-03-12

    Substantial research has shown that emotions play a critical role in physical health. However, most of these studies were conducted in industrialized countries, and it is still an open question whether the emotion-health connection is a "first-world problem". In the current study, we examined socio-economic development's influence on emotion-health connection by performing multilevel-modeling analysis in a dataset of 33,600 individuals from 162 counties in China. Results showed that both positive emotions and negative emotions predicted level of physical health and regional Gross Domestic Product Per Capita (GDPPC) had some impact on the association between emotion and health through accessibility of medical resources and educational status. But these impacts were suppressed, and the total effects of GDPPC on emotion-health connections were not significant. These results support the universality of emotion-health connection across levels of GDPPC and provide new insight into how socio-economic development might affect these connections.

  17. Guideline for determining the mean glandular dose according to DIN 6868-162 and threshold contrast visibility according to the quality assurance guideline for digital mammography systems.

    Science.gov (United States)

    Sommer, A; Schopphoven, S; Land, I; Blaser, D; Sobczak, T

    2014-05-01

    As part of the physico-technical quality assurance of the German breast cancer screening program, the threshold contrast visibility and the average glandular dose of every digital mammography system have to fulfill the requirements of the "European guidelines for quality assurance in breast cancer screening and diagnosis" (4th Edition). To accomplish uniform measurements in all federal states of Germany, the physical board of the reference centers developed a special guideline in 2009. Due to recent changes in the guidelines and standards, a second version of the guideline was developed by the reference centers. This guideline describes the determination of the average glandular dose as well as the CDMAM image acquisition and the CDMAM image evaluation. The determination of the threshold contrast visibility can be performed visually or automatically. The determination of the average glandular dose is based on DIN 6868 - 162 and the threshold contrast visibility test is based on the German "Quality Assurance Guideline". © Georg Thieme Verlag KG Stuttgart · New York.

  18. Targeted therapy for sarcomas

    Directory of Open Access Journals (Sweden)

    Forscher C

    2014-03-01

    Full Text Available Charles Forscher,1 Monica Mita,2 Robert Figlin3 1Sarcoma Program, Samuel Oschin Comprehensive Cancer Institute, Cedars-Sinai Medical Center, Los Angeles, CA, USA; 2Experimental Therapeutics Program, Samuel Oschin Comprehensive Cancer Institute, Cedars-Sinai Medical Center, Los Angeles, CA, USA; 3Academic Development Program, Samuel Oschin Comprehensive Cancer Institute, and Division of Hematology/Oncology, Cedars-Sinai Medical Center, Los Angeles, CA, USA Abstract: Sarcomas are tumors of mesenchymal origin that make up approximately 1% of human cancers. They may arise as primary tumors in either bone or soft tissue, with approximately 11,280 soft tissue tumors and 2,650 bone tumors diagnosed each year in the United States. There are at least 50 different subtypes of soft tissue sarcoma, with new ones described with ever-increasing frequency. One way to look at sarcomas is to divide them into categories on the basis of their genetic make-up. One group of sarcomas has an identifiable, relatively simple genetic signature, such as the X:18 translocation seen in synovial sarcoma or the 11:22 translocation seen in Ewing's sarcoma. These specific abnormalities often lead to the presence of fusion proteins, such as EWS-FLI1 in Ewing's sarcoma, which are helpful as diagnostic tools and may become therapeutic targets in the future. Another group of sarcomas is characterized by complex genetic abnormalities as seen in leiomyosarcoma, osteosarcoma, and undifferentiated sarcoma. It is important to keep these distinctions in mind when contemplating the development of targeted agents for sarcomas. Different abnormalities in sarcoma could be divided by tumor subtype or by the molecular or pathway abnormality. However, some existing drugs or drugs in development may interfere with or alter more than one of the presented pathways. Keywords: sarcoma, targeted agents, tyrosine kinase inhibitors, mTor inhibition

  19. Targeted mass spectrometry

    DEFF Research Database (Denmark)

    Osinalde, Nerea; Aloria, Kerman; Omaetxebarria, Miren J.

    2017-01-01

    Following the rapid expansion of the proteomics field, the investigation of post translational modifications (PTM) has become extremely popular changing our perspective of how proteins constantly fine tune cellular functions. Reversible protein phosphorylation plays a pivotal role in virtually all...... for becoming the method of choice to study with high precision and sensitivity already known site-specific phosphorylation events. This review summarizes the contribution of large-scale unbiased MS analyses and highlights the need of targeted MS-based approaches for follow-up investigation. Additionally...

  20. Fixed target beams

    CERN Document Server

    Kain, V; Cettour-Cave, S; Cornelis, K; Fraser, M A; Gatignon, L; Goddard, B; Velotti, F

    2017-01-01

    The CERN SPS (Super Proton Synchrotron) serves asLHC injector and provides beam for the North Area fixedtarget experiments. At low energy, the vertical acceptancebecomes critical with high intensity large emittance fixed tar-get beams. Optimizing the vertical available aperture is a keyingredient to optimize transmission and reduce activationaround the ring. During the 2016 run a tool was developed toprovide an automated local aperture scan around the entirering.The flux of particles slow extracted with the1/3inte-ger resonance from the Super Proton Synchrotron at CERNshould ideally be constant over the length of the extractionplateau, for optimum use of the beam by the fixed target ex-periments in the North Area. The extracted intensity is con-trolled in feed-forward correction of the horizontal tune viathe main SPS quadrupoles. The Mains power supply noiseat 50 Hz and harmonics is also corrected in feed-forwardby small amplitude tune modulation at the respective fre-quencies with a dedicated additional quad...

  1. Vitamin D depletion aggravates hypertension and target-organ damage

    DEFF Research Database (Denmark)

    Andersen, Louise Bjørkholt; Przybyl, Lukasz; Haase, Nadine

    2015-01-01

    BACKGROUND: We tested the controversial hypothesis that vitamin D depletion aggravates hypertension and target-organ damage by influencing renin. METHODS AND RESULTS: Four-week-old double-transgenic rats (dTGR) with excess angiotensin (Ang) II production due to overexpression of the human renin (h......REN) and angiotensinogen (hAGT) genes received vitamin D-depleted (n=18) or standard chow (n=15) for 3 weeks. The depleted group had very low serum 25-hydroxyvitamin D levels (mean±SEM; 3.8±0.29 versus 40.6±1.19 nmol/L) and had higher mean systolic BP at week 5 (158±3.5 versus 134.6±3.7 mm Hg, P....6±3.3 versus 162.3±3.8 mm Hg, PVitamin D depletion led to increased relative heart weights and increased serum creatinine concentrations. Furthermore, the mRNAs of natriuretic peptides, neutrophil gelatinase-associated lipocalin, hREN, and r...

  2. Intestinal mucosa is a target tissue for pancreatic polypeptide

    International Nuclear Information System (INIS)

    Gilbert, W.R.; Kramer, J.L.; Frank, B.H.; Gingerich, R.L.

    1986-01-01

    Studies were carried out to identify mammalian tissues capable of specifically binding mammalian pancreatic polypeptide (PP). Bovine PP (bPP) radiolabeled with 125 I was purified by HPLC to yield [ 125 I]iodo-(Tyr-27) bPP. The label was injected into three pairs of fasted littermate dogs and allowed to circulate for 5 min. One of the dogs was a control which received an excess of unlabeled porcine PP to provide competition for receptor binding. Unbound bPP was removed by perfusion with Krebs-Ringer bicarbonate and the tissue fixed in situ with Karnovsky's fixative. Tissue samples from various organs were removed, weighed, and counted. The entire gastrointestinal tract demonstrated high levels of 125 I after injection of the labeled peptide. The duodenum, jejunum, ileum, and colon were the only tissues to exhibit specific binding of bPP. These tissues (mucosal and muscle layers) from experimental animals exhibited 31-76% higher binding than the corresponding tissues from the control animals. Sections of the gastrointestinal tract were scraped to separate the mucosal layer from the underlying muscle layer. The mucosal layer of the duodenum, jejunum, and ileum exhibited 145-162% increases in binding compared to the control animals. The muscle layer of these tissues demonstrated no significant increase. These findings demonstrate that mucosal layer of the small intestine is a target tissue for mammalian PP

  3. Electroplating of Uranium -Foil Target With Ni And Zn

    International Nuclear Information System (INIS)

    Husna AI Hasa, Muhammad; Suripto, Asmedi

    2001-01-01

    The uranium foil target, which was produced by rolling, was subjected to preparation treatment prior to the electroplating. The electroplating produced certain plate thickness on the foil surface. The electroplating was applied to the uranium foil of 71 mm long and 46 mm wide using plating materials of Ni and Zn. The plating is intended to serve as barrier for fission fragment recoils, which are produced during irradiation. The plate thickness produced by the electroplating was measured by a micrometer and an analytical balance. The electroplating with Ni produced plate-thickness of 8,9 mm when measured by the micrometer, or 11.4 mm when measured by the analytical balance, while the Zn electroplating produced greater plate-thickness, i.e. 16.2 mm by the micrometer measurement or 13.7 mm by the analytical balance measurement. The current efficiency of the electroplating was 62 % for Ni and 80 % for Zn. It was observed that the optimum condition for the electroplating depended on the plating materials, plating time, and current density. The plate-thickness produced under the optimum condition was 7-15 mm at 15 mA/cm 2 for Ni and ]0 mA/cm 2 for Zn with plating time of 60 minutes

  4. Synthesis and characterization of phosphors based on calcium and magnesium silicates doped with europium and dysprosium; Síntese e caracterização de fósforos a base de silicatos de cálcio e magnésio dopados com európio e disprósio

    Energy Technology Data Exchange (ETDEWEB)

    Misso, Agatha Matos

    2016-07-01

    Ca and Mg silicates based phosphors were prepared by sol-gel method combined with the molten salts process. The gel of silica was obtained from Na{sub 2}SiO{sub 3} solution by using europium, dysprosium, calcium and magnesium chloride solutions. Therefore, those chlorides were homogeneously dispersed into the gel. The obtained gel was dried and heat treated to 900° C for 1h to allow the fusion of the present salts. Then it was water washed until negative test for Cl{sup -}, and dried. The reduction of the europium to Eu{sup 2+} was performed under atmosphere of 5% of H{sub 2} and 95% of Ar to 900° C for 3h, to reach CaMgSi{sub 2}O{sub 6}:Eu{sup 2+} and CaMgSi{sub 2}O{sub 6}:Eu{sup 2+}:Dy{sup 3+} phosphors. Diopside was identified as main crystalline phase and quartz, as secondary phase from XRD (X-ray diffraction) patterns. SEM (scanning electron microscopy) micrographs, of the samples showed needles, spheres, leaves and rods of particles and agglomerates. Thermal analysis (TGA-DTGA) curves revealed that the crystallization temperature of CaMgSi{sub 2}O{sub 6}:Eu{sup 2+} lies around 765° C. Photoluminescence spectroscopy of the phosphors was studied based on interconfigurational 4f{sup N} → 4f{sup N-1} 5d transition of Eu{sup 2+} ion. The spectra of excitation showed 4f{sup N} → 4f{sup N-1} 5d transition of Eu{sup 2+} ion broad band, related to the ligand to metal charge transfer transition (LMCT) O{sup 2-} (2p) → Eu{sup 3+} in the 250 nm region, when the emission is monitored at 583,5 nm. It also presents the 4f ↔ 4f transitions of Eu{sup 3+} ion bands, showing the {sup 7}F{sub 0} → {sup 5}L{sub 6} transition at 393 nm. From emission spectra with excitation monitored at 393 nm, it can be observed fine peaks between 570 and 750 nm which are characteristics of {sup 5}D{sub 0} → {sup 7}F{sub J} (J = 0 - 5) transition of Eu{sup 3+} ion, indicating that the Eu{sup 3+} ion occupies a site with center of inversion. Finally, the obtained results indicate

  5. Aquaporin-2 membrane targeting

    DEFF Research Database (Denmark)

    Olesen, Emma T B; Fenton, Robert A

    2017-01-01

    The targeting of the water channel aquaporin-2 (AQP2) to the apical plasma membrane of kidney collecting duct principal cells is regulated mainly by the antidiuretic peptide hormone arginine vasopressin (AVP). This process is of crucial importance for the maintenance of body water homeostasis...... of aquaporin-2 (AQP2) to the apical plasma membrane of collecting duct (CD) principal cells (10, 20). This process is mainly regulated by the actions of AVP on the type 2 AVP receptor (V2R), although the V1a receptor may also play a minor role (26). The V2R is classified within the group of 7-transmembrane....... For example, 1) stimulation with the nonspecific AC activator forskolin increases AQP2 membrane accumulation in a mouse cortical collecting duct cell line [e.g., Norregaard et al. (16)]; 2) cAMP increases CD water permeability (15); 3) the cAMP-activated protein kinase A (PKA) can phosphorylate AQP2 on its...

  6. ORION laser target diagnostics

    International Nuclear Information System (INIS)

    Bentley, C. D.; Edwards, R. D.; Andrew, J. E.; James, S. F.; Gardner, M. D.; Comley, A. J.; Vaughan, K.; Horsfield, C. J.; Rubery, M. S.; Rothman, S. D.; Daykin, S.; Masoero, S. J.; Palmer, J. B.; Meadowcroft, A. L.; Williams, B. M.; Gumbrell, E. T.; Fyrth, J. D.; Brown, C. R. D.; Hill, M. P.; Oades, K.

    2012-01-01

    The ORION laser facility is one of the UK's premier laser facilities which became operational at AWE in 2010. Its primary mission is one of stockpile stewardship, ORION will extend the UK's experimental plasma physics capability to the high temperature, high density regime relevant to Atomic Weapons Establishment's (AWE) program. The ORION laser combines ten laser beams operating in the ns regime with two sub ps short pulse chirped pulse amplification beams. This gives the UK a unique combined long pulse/short pulse laser capability which is not only available to AWE personnel but also gives access to our international partners and visiting UK academia. The ORION laser facility is equipped with a comprehensive suite of some 45 diagnostics covering optical, particle, and x-ray diagnostics all able to image the laser target interaction point. This paper focuses on a small selection of these diagnostics.

  7. ORION laser target diagnostics.

    Science.gov (United States)

    Bentley, C D; Edwards, R D; Andrew, J E; James, S F; Gardner, M D; Comley, A J; Vaughan, K; Horsfield, C J; Rubery, M S; Rothman, S D; Daykin, S; Masoero, S J; Palmer, J B; Meadowcroft, A L; Williams, B M; Gumbrell, E T; Fyrth, J D; Brown, C R D; Hill, M P; Oades, K; Wright, M J; Hood, B A; Kemshall, P

    2012-10-01

    The ORION laser facility is one of the UK's premier laser facilities which became operational at AWE in 2010. Its primary mission is one of stockpile stewardship, ORION will extend the UK's experimental plasma physics capability to the high temperature, high density regime relevant to Atomic Weapons Establishment's (AWE) program. The ORION laser combines ten laser beams operating in the ns regime with two sub ps short pulse chirped pulse amplification beams. This gives the UK a unique combined long pulse/short pulse laser capability which is not only available to AWE personnel but also gives access to our international partners and visiting UK academia. The ORION laser facility is equipped with a comprehensive suite of some 45 diagnostics covering optical, particle, and x-ray diagnostics all able to image the laser target interaction point. This paper focuses on a small selection of these diagnostics.

  8. Optimal exploration target zones

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2008-09-01

    Full Text Available prospective map are the weights-of-evidence (WofE) method logistic regression canonical favorability analysis neural networks evidential belief functions Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote.... . . ): FITNESS FUNCTION φWMSD+V(Sn) = λ N(A) ∑ −→x ∈A P(−→x ) ∣ ∣ ∣ ∣−→x −QSn( −→x ) ∣ ∣ ∣ ∣ +(1− λ)s2(OSn) , (2) where QSn( −→x ) is the location vector of an optimal exploration focal point in Sn nearest to −→x , and s2(OSn) is the variance...

  9. Bradycardia During Targeted Temperature Management

    DEFF Research Database (Denmark)

    Thomsen, Jakob Hartvig; Nielsen, Niklas; Hassager, Christian

    2016-01-01

    OBJECTIVES: Bradycardia is common during targeted temperature management, likely being a physiologic response to lower body temperature, and has recently been associated with favorable outcome following out-of-hospital cardiac arrest in smaller observational studies. The present study sought...... to confirm this finding in a large multicenter cohort of patients treated with targeted temperature management at 33°C and explore the response to targeted temperature management targeting 36°C. DESIGN: Post hoc analysis of a prospective randomized study. SETTING: Thirty-six ICUs in 10 countries. PATIENTS......: We studied 447 (targeted temperature management = 33°C) and 430 (targeted temperature management = 36°C) comatose out-of-hospital cardiac arrest patients with available heart rate data, randomly assigned in the targeted temperature management trial from 2010 to 2013. INTERVENTIONS: Targeted...

  10. An Approach for Automatic Orientation of Big Point Clouds from the Stationary Scanners Based on the Spherical Targets

    Directory of Open Access Journals (Sweden)

    YAO Jili

    2015-04-01

    Full Text Available Terrestrial laser scanning (TLS technology has high speed of data acquisition, large amount of point cloud, long distance of measuring. However, there are some disadvantages such as distance limitation in target detecting, hysteresis in point clouds processing, low automation and weaknesses of adapting long-distance topographic survey. In this case, we put forward a method on long-range targets detecting in big point clouds orientation. The method firstly searches point cloud rings that contain targets according to their engineering coordinate system. Then the detected rings are divided into sectors to detect targets in a very short time so as to obtain central coordinates of these targets. Finally, the position and orientation parameters of scanner are calculated and point clouds in scanner's own coordinate system(SOCS are converted into engineering coordinate system. The method is able to be applied in ordinary computers for long distance topographic(the distance between scanner and targets ranges from 180 to 700 m survey in mountainous areas with targets radius of 0.162m.

  11. Solid Polarized Targets and Applications

    International Nuclear Information System (INIS)

    Crabb, D. G.

    2008-01-01

    Examples are given of dynamically polarized targets in use today and how the subsystems have changed to meet the needs of todays experiments. Particular emphasis is placed on target materials such as ammonia and lithium deuteride. Recent polarization studies of irradiated materials such as butanol, deuterated butanol, polyethylene, and deuterated polyethylene are presented. The operation of two non-DNP target systems as well as applications of traditional DNP targets are briefly discussed

  12. Techniques for preparing isotopic targets

    International Nuclear Information System (INIS)

    Xu Guoji; Guan Shouren; Luo Xinghua; Sun Shuhua

    1987-12-01

    The techniques of making isotopic targets for nuclear physics experiments are introduced. Vacuum evaporation, electroplating, centrifugal precipitation, rolling and focused heavy-ion beam sputtering used to prepare various isotopic targets at IAE are described. Reduction-distillation with active metals and electrolytic reduction for converting isotope oxides to metals are mentioned. The stripping processes of producing self-supporting isotopic targets are summarized. The store methods of metallic targets are given

  13. Nova target diagnostics control system

    International Nuclear Information System (INIS)

    Severyn, J.R.

    1985-01-01

    During the past year the Nova target diagnostics control system was finished and put in service. The diagnostics loft constructed to the north of the target room provides the environmental conditions required to collect reliable target diagnostic data. These improvements include equipment cooling and isolation of the power source with strict control of instrumentation grounds to eliminate data corruption due to electromagnetic pulses from the laser power-conditioning system or from target implosion effects

  14. Stanford polarized atomic beam target

    International Nuclear Information System (INIS)

    Mavis, D.G.; Dunham, J.S.; Hugg, J.W.; Glavish, H.F.

    1976-01-01

    A polarized atomic beam source was used to produce an atomic hydrogen beam which was in turn used as a polarized proton target. A target density of 2 x 10'' atoms/cm 3 and a target polarization of 0.37 without the use of rf transitions were measured. These measurements indicate that a number of experiments are currently feasible with a variety of polarized target beams

  15. 159 - 162_Kogo_Aniline

    African Journals Online (AJOL)

    pc

    mechanical properties of doped polyester fabric with aniline w s of various ... tion of the PANI solution rly constant up to ... computer interface and printer according to the AS. Figure 2: .... Material Systems and Structures, 23(17), pp. 1969-1986.

  16. Integrated fast ignition simulation of cone-guided target with three codes

    Energy Technology Data Exchange (ETDEWEB)

    Sakagami, H. [Hyogo Univ., Computer Engineering, Himeji, Hyogo (Japan); Johzaki, T.; Nagatomo, H.; Mima, K. [Osaka Univ., Institute of Laser Engineering, Suita, Osaka (Japan)

    2004-07-01

    It was reported that the fuel core was heated up to {approx} 0.8 keV in the fast ignition experiments with cone-guided targets, but they could not theoretically explain heating mechanisms and achievement of such high temperature. Thus simulations should play an important role in estimating the scheme performance, and we must simulate each phenomenon with individual codes and integrate them under the Fast Ignition Integrated Interconnecting code project. In the previous integrated simulations, fast electrons generated by the laser-plasma interaction were too hot to efficiently heat the core and we got only a 0.096 keV temperature rise. Including the density gap at the contact surface between the cone tip and the imploded plasma, the period of core heating became longer and the core was heated by 0.162 keV, about 69% higher increment compared with ignoring the density gap effect. (authors)

  17. Profiling micro rnas and their targets in radish (raphanus sativus l.)

    International Nuclear Information System (INIS)

    Barozai, M.Y.; Din, M.

    2015-01-01

    MicroRNAs (miRNAs) are tiny, non-protein coding and negative regulatory RNAs approximately 21 nucleotides in length. The comparative genomic methodology due to their conserved nature is a reasonable approach for the novel miRNAs discovery. In this research, total 25 novel miRNAs from 18 families (ras-miR-156, 160, 162, 163, 164, 167, 168, 319, 399, 408, 413, 414, 841, 1310, 2936, 5030 and 5661) are identified in an important vegetable radish (Raphanus sativus L.). The 25 miRNA precursor sequences showed secondary structures with the mature miRNAs in the stem region. Total 42 putative targets are also identified for the novel 25 radish miRNAs. These findings suggest that more thorough understanding of the function of such miRNAs will help to unravel the mysteries role in plant biology. (author)

  18. Targets for heavy ion fusion

    International Nuclear Information System (INIS)

    Clauser, M.J.

    1978-01-01

    This paper describes some of the basic principles of fusion target implosions, using some simple targets designed for irradiation by ion beams. Present estimates are that ion beams with 1-5 MJ, and 100-500 TW will be required to ignite high gain targets. (orig.) [de

  19. Beam heating of target foils

    International Nuclear Information System (INIS)

    Corwin, W.C.

    1975-01-01

    A target rotator, built to reduce the effects of beam spot heating, is fully adjustable, holds three targets, is chamber independent, and takes up limited space. The expected temperature rise in the target is calculated from the Stefan--Boltzmann law

  20. Photodissociation spectroscopy of the dysprosium monochloride molecular ion

    Energy Technology Data Exchange (ETDEWEB)

    Dunning, Alexander, E-mail: alexander.dunning@gmail.com; Schowalter, Steven J.; Puri, Prateek; Hudson, Eric R. [Department of Physics and Astronomy, University of California, Los Angeles, California 90095 (United States); Petrov, Alexander; Kotochigova, Svetlana [Department of Physics, Temple University, Philadelphia, Pennsylvania 19122 (United States)

    2015-09-28

    We have performed a combined experimental and theoretical study of the photodissociation cross section of the molecular ion DyCl{sup +}. The photodissociation cross section for the photon energy range 35 500 cm{sup −1} to 47 500 cm{sup −1} is measured using an integrated ion trap and time-of-flight mass spectrometer; we observe a broad, asymmetric profile that is peaked near 43 000 cm{sup −1}. The theoretical cross section is determined from electronic potentials and transition dipole moments calculated using the relativistic configuration-interaction valence-bond and coupled-cluster methods. The electronic structure of DyCl{sup +} is extremely complex due to the presence of multiple open electronic shells, including the 4f{sup 10} configuration. The molecule has nine attractive potentials with ionically bonded electrons and 99 repulsive potentials dissociating to a ground state Dy{sup +} ion and Cl atom. We explain the lack of symmetry in the cross section as due to multiple contributions from one-electron-dominated transitions between the vibrational ground state and several resolved repulsive excited states.

  1. Influence of dysprosium addition on the structural, morphological ...

    Indian Academy of Sciences (India)

    Microwave absorption properties of hexaferrite (70 wt%)–acrylic resin. (30 wt%) composites ... the RE ions were substituted for Sr (Ba) or Fe, taking into accounts the .... general the RE substitutions weaken the super exchange interactions ...

  2. Single molecule magnet behaviour in robust dysprosium-biradical complexes.

    Science.gov (United States)

    Bernot, Kevin; Pointillart, Fabrice; Rosa, Patrick; Etienne, Mael; Sessoli, Roberta; Gatteschi, Dante

    2010-09-21

    A Dy-biradical complex was synthesized and characterized down to very low temperature. ac magnetic measurements reveal single molecule magnet behaviour visible without any application of dc field. The transition to the quantum tunneling regime is evidenced. Photophysical and EPR measurements provide evidence of the excellent stability of these complexes in solution.

  3. Scissors Mode of Dipolar Quantum Droplets of Dysprosium Atoms

    Science.gov (United States)

    Ferrier-Barbut, Igor; Wenzel, Matthias; Böttcher, Fabian; Langen, Tim; Isoard, Mathieu; Stringari, Sandro; Pfau, Tilman

    2018-04-01

    We report on the observation of the scissors mode of a single dipolar quantum droplet. The existence of this mode is due to the breaking of the rotational symmetry by the dipole-dipole interaction, which is fixed along an external homogeneous magnetic field. By modulating the orientation of this magnetic field, we introduce a new spectroscopic technique for studying dipolar quantum droplets. This provides a precise probe for interactions in the system, allowing us to extract a background scattering length for 164Dy of 69 (4 )a0 . Our results establish an analogy between quantum droplets and atomic nuclei, where the existence of the scissors mode is also only due to internal interactions. They further open the possibility to explore physics beyond the available theoretical models for strongly dipolar quantum gases.

  4. Calorimetric investigation of an yttrium-dysprosium spin glass

    International Nuclear Information System (INIS)

    Wenger, L.E.

    1978-01-01

    In an effort to compare the spin glass characteristics of yttrium--rare earth alloys with those of the noble-metal spin glasses, the susceptibility and heat capacity of Y/sub 0.98/Dy/sub 0.02/ have been measured in the temperature range 2.5--40 K. The low-field ac susceptibility measurement shows the characteristic cusp-like peak at 7.64 K. The magnetic specific heat of the same sample shows a peak at 7.0 K and may be qualitatively described as a semi-cusp. The magnetic entropy change from absolute zero to 7 K is approximately 0.52 of cR ln(2J+1). These results are qualitatively different than previous calorimetric results on the archetypal spin glasses, AuFe and CuMn, where rounded maxima are observed at temperatures above the spin glass transition temperatures

  5. Emission spectra of yttrium vanadate doped with bismuth and dysprosium

    International Nuclear Information System (INIS)

    Pawar, B.V.; Patil, R.N.

    1975-01-01

    The fluorescence spectra of YVO 4 :Bi and YVO 4 :Bi:Dy phosphors under X-rays and ultra-violet radiation have been studied. The observations on the phosphors with constant Bi 3+ and varying Dy 3+ concentration can be attributed to radiationless transfer of energy from Bi 3+ to Dy 3+ coupled with non-radiative losses due to self-quenching at higher level of Dy 3+ concentration. While the observations on the phosphors with constant Dy 3+ and varying Bi 3+ concentration indicate that there is radiationless transfer from Bi 3+ to Dy 3+ under X-ray or UV irradiation. (author)

  6. Dysprosium-free melt-spun permanent magnets

    International Nuclear Information System (INIS)

    Brown, D N; Wu, Z; He, F; Miller, D J; Herchenroeder, J W

    2014-01-01

    Melt-spun NdFeB powders can be formed into a number of different types of permanent magnet for a variety of applications in electronics, automotive and clean technology industries. The melt-spinning process produces flake powder with a fine uniform array of nanoscale Nd 2 Fe 14 B grains. These powders can be net-shape formed into isotropic polymer-bonded magnets or hot formed into fully dense magnets. This paper discusses the influence of heavy rare earth elements and microstructure on the magnetic performance, thermal stability and material cost of NdFeB magnets. Evidence indicates that melt-spun nanocrystalline NdFeB magnets are less dependent on heavy rare earth elements for high-temperature performance than the alternative coarser-grained sintered NdFeB magnets. In particular, hot-pressed melt-spun magnets are an attractive low-cost solution for applications that require thermal stability up to 175–200 °C. (paper)

  7. Dysprosium-free melt-spun permanent magnets.

    Science.gov (United States)

    Brown, D N; Wu, Z; He, F; Miller, D J; Herchenroeder, J W

    2014-02-12

    Melt-spun NdFeB powders can be formed into a number of different types of permanent magnet for a variety of applications in electronics, automotive and clean technology industries. The melt-spinning process produces flake powder with a fine uniform array of nanoscale Nd2Fe14B grains. These powders can be net-shape formed into isotropic polymer-bonded magnets or hot formed into fully dense magnets. This paper discusses the influence of heavy rare earth elements and microstructure on the magnetic performance, thermal stability and material cost of NdFeB magnets. Evidence indicates that melt-spun nanocrystalline NdFeB magnets are less dependent on heavy rare earth elements for high-temperature performance than the alternative coarser-grained sintered NdFeB magnets. In particular, hot-pressed melt-spun magnets are an attractive low-cost solution for applications that require thermal stability up to 175-200 °C.

  8. Crystal and molecular structure of dysprosium (3) n-aminobenzoate

    International Nuclear Information System (INIS)

    Khiyalov, M.S.; Amiraslanov, I.R.; Mamedov, Kh.S.; Movsumov, Eh.M.

    1981-01-01

    The X ray diffraction investigation of the Dy(NH 2 C 6 H 4 COO) 3 x3H 2 O complex is carried out. Triclinic crystals have lattice parameters α=11.095(15), b=9.099(17), c=12.780 (15)A, α=108.051(12), β=89.072(10); γ=104.954(12) 0 , space group P anti 1, Z=2. The structure consists of dimer molecules. The third water molecule in the formula is an outer spherical one. The average lengths of Dy-O and Dy-OH 2 are 2.39 and 2.40 A respectively, the average value of Dy-O in bridge carboxylates (2.26A) is remarkably shorter. Hydrogen bonds between amine ligand ends, carboxylic groups oxygen and water molecules bind complex molecules into the three-dimensional frame [ru

  9. Microscopic study of neutron-rich dysprosium isotopes

    International Nuclear Information System (INIS)

    Vargas, Carlos E.; Velazquez, Victor; Lerma, Sergio

    2013-01-01

    Microscopic studies in heavy nuclei are very scarce due to large valence spaces involved. This computational problem can be avoided by means of the use of symmetry-based models. Ground-state, γ and β bands, and their B(E2) transition strengths in 160-168 Dy isotopes, are studied in the framework of the pseudo-SU(3) model which includes the preserving symmetry Q . Q term and the symmetry-breaking Nilsson and pairing terms, systematically parametrized. Additionally, three rotor-like terms are considered, whose free parameters, fixed for all members of the chain, are used to fine tune the moment of inertia of rotational bands and the band head of γ and β bands. The model succesfully describes in a systematic way rotational features in these nuclei and allows to extrapolate toward the midshell nucleus 170 Dy. The results presented show that it is possible to study a full chain of isotopes or isotones in the region with the present model. (orig.)

  10. Microscopic study of neutron-rich dysprosium isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Vargas, Carlos E. [Universidad Veracruzana, Facultad de Fisica e Inteligencia Artificial, Xalapa (Mexico); Universidad Nacional Autonoma de Mexico, Facultad de Ciencias, Apartado Postal 70-542, Mexico D.F. (Mexico); Velazquez, Victor [Universidad Nacional Autonoma de Mexico, Facultad de Ciencias, Apartado Postal 70-542, Mexico D.F. (Mexico); Lerma, Sergio [Universidad Veracruzana, Facultad de Fisica e Inteligencia Artificial, Xalapa (Mexico)

    2013-01-15

    Microscopic studies in heavy nuclei are very scarce due to large valence spaces involved. This computational problem can be avoided by means of the use of symmetry-based models. Ground-state, {gamma} and {beta} bands, and their B(E2) transition strengths in {sup 160-168}Dy isotopes, are studied in the framework of the pseudo-SU(3) model which includes the preserving symmetry Q . Q term and the symmetry-breaking Nilsson and pairing terms, systematically parametrized. Additionally, three rotor-like terms are considered, whose free parameters, fixed for all members of the chain, are used to fine tune the moment of inertia of rotational bands and the band head of {gamma} and {beta} bands. The model succesfully describes in a systematic way rotational features in these nuclei and allows to extrapolate toward the midshell nucleus {sup 170}Dy. The results presented show that it is possible to study a full chain of isotopes or isotones in the region with the present model. (orig.)

  11. Structural and magnetic study of dysprosium substituted cobalt ferrite nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Hemaunt, E-mail: hvatsal@gmail.com [Department of Physics, Govind Ballabh Pant University of Agr. & Technology, Pantnagar, Uttarakhand 263145 (India); Srivastava, R.C. [Department of Physics, Govind Ballabh Pant University of Agr. & Technology, Pantnagar, Uttarakhand 263145 (India); Pal Singh, Jitendra [Advanced Analysis Centre, Korea Institute of Science and Technology, Seoul 02792 (Korea, Republic of); Negi, P. [Department of Physics, Govind Ballabh Pant University of Agr. & Technology, Pantnagar, Uttarakhand 263145 (India); Agrawal, H.M. [Advanced Analysis Centre, Korea Institute of Science and Technology, Seoul 02792 (Korea, Republic of); Das, D. [UGC-DAE CSR Kolkata Centre, Kolkata 700098 (India); Hwa Chae, Keun [Advanced Analysis Centre, Korea Institute of Science and Technology, Seoul 02792 (Korea, Republic of)

    2016-03-01

    The present work investigates the magnetic behavior of Dy{sup 3+} substituted cobalt ferrite nanoparticles. X-ray diffraction studies reveal presence of cubic spinel phases in these nanoparticles. Raman spectra of these nanoparticles show change in intensity of Raman bands, which reflects cation redistribution in cubic spinel lattice. Saturation magnetization and coercivity decrease with increase of Dy{sup 3+}concentration in these nanoparticles. Room temperature Mössbauer measurements show the cation redistribution in these nanoparticles and corroborates the results obtained from Raman Spectroscopic measurements. Decrease in magnetization of Dy{sup 3+} substituted cobalt ferrite is attributed to the reduction in the magnetic interaction and cation redistribution. - Highlights: • Slight decrease in crystallite size after Dy{sup 3+} doping. • Saturation magnetization and coercivity decrease after Dy{sup 3+} doping. • Mössbauer measurements show the cation redistribution in the samples.

  12. Dysprosium Acetylacetonato Single-Molecule Magnet Encapsulated in Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Ryo Nakanishi

    2016-12-01

    Full Text Available Dy single-molecule magnets (SMMs, which have several potential uses in a variety of applications, such as quantum computing, were encapsulated in multi-walled carbon nanotubes (MWCNTs by using a capillary method. Encapsulation was confirmed by using transmission electron microscopy (TEM. In alternating current magnetic measurements, the magnetic susceptibilities of the Dy acetylacetonato complexes showed clear frequency dependence even inside the MWCNTs, meaning that this hybrid can be used as magnetic materials in devices.

  13. Study of elastic pion scattering from /sup 9/Be, /sup 28/Si, /sup 58/Ni, and /sup 208/Pb at 162 MeV. [Total and differential cross sections, scattering yields, scattering amplitudes

    Energy Technology Data Exchange (ETDEWEB)

    Devereux, M.J.

    1979-05-01

    Elastic pion scattering from /sup 9/Be, /sup 28/Si, /sup 58/Ni, and /sup 208/Pb at 162 MeV is analyzed and compared with an optical model theory which incorporates a pion--nucleon range. Excellent fits to the data are obtained in all but one case. The fitted values of the pion--nucleon range, as well as other fitted values are listed. 108 references.

  14. Targeting the urokinase plasminogen activator receptor inhibits ovarian cancer metastasis.

    Science.gov (United States)

    Kenny, Hilary A; Leonhardt, Payton; Ladanyi, Andras; Yamada, S Diane; Montag, Anthony; Im, Hae Kyung; Jagadeeswaran, Sujatha; Shaw, David E; Mazar, Andrew P; Lengyel, Ernst

    2011-02-01

    To understand the functional and preclinical efficacy of targeting the urokinase plasminogen activator receptor (u-PAR) in ovarian cancer. Expression of u-PAR was studied in 162 epithelial ovarian cancers, including 77 pairs of corresponding primary and metastatic tumors. The effect of an antibody against u-PAR (ATN-658) on proliferation, adhesion, invasion, apoptosis, and migration was assessed in 3 (SKOV3ip1, HeyA8, and CaOV3) ovarian cancer cell lines. The impact of the u-PAR antibody on tumor weight, number, and survival was examined in corresponding ovarian cancer xenograft models and the mechanism by which ATN-658 blocks metastasis was explored. Only 8% of all ovarian tumors were negative for u-PAR expression. Treatment of SKOV3ip1, HeyA8, and CaOV3 ovarian cancer cell lines with the u-PAR antibody inhibited cell invasion, migration, and adhesion. In vivo, anti-u-PAR treatment reduced the number of tumors and tumor weight in CaOV3 and SKOV3ip1 xenografts and reduced tumor weight and increased survival in HeyA8 xenografts. Immunostaining of CaOV3 xenograft tumors and ovarian cancer cell lines showed an increase in active-caspase 3 and TUNEL staining. Treatment with u-PAR antibody inhibited α(5)-integrin and u-PAR colocalization on primary human omental extracellular matrix. Anti-u-PAR treatment also decreased the expression of urokinase, u-PAR, β(3)-integrin, and fibroblast growth factor receptor-1 both in vitro and in vivo. This study shows that an antibody against u-PAR reduces metastasis, induces apoptosis, and reduces the interaction between u-PAR and α(5)-integrin. This provides a rationale for targeting the u-PAR pathway in patients with ovarian cancer and for further testing of ATN-658 in this indication. ©2010 AACR.

  15. Hypoxia targeting copper complexes

    International Nuclear Information System (INIS)

    Dearling, J.L.

    1998-11-01

    The importance and incidence of tumour hypoxia, its measurement and current treatments available, including pharmacological and radiopharmacological methods of targeting hypoxia, are discussed. A variety of in vitro and in vivo methods for imposing hypoxia have been developed and are reviewed. Copper, its chemistry, biochemistry and radiochemistry, the potential for use of copper radionuclides and its use to date in this field is considered with particular reference to the thiosemicarbazones. Their biological activity, metal chelation, in vitro and in vivo studies of their radiocopper complexes and the potential for their use as hypoxia targeting radiopharmaceuticals is described. The reduction of the copper(II) complex to copper(l), its pivotal importance in their biological behaviour, and the potential for manipulation of this to effect hypoxia selectivity are described. An in vitro method for assessing the hypoxia selectivity of radiopharmaceuticals is reported. The rapid deoxygenation and high viability of a mammalian cell culture in this system is discussed and factors which may affect the cellular uptake of a radiopharmaceutical are described. The design, synthesis and complexation with copper and radiocopper of a range of bis(thiosemicarbazones) is reported. Synthesis of these compounds is simple giving high yields of pure products. The characteristics of the radiocopper complexes ( 64 Cu) including lipophilicity and redox activity are reported (reduction potentials in the range -0.314 - -0.590 V). High cellular uptakes of the radiocopper complexes of the ligands, in hypoxic and normoxic EMT6 and CHO320 cells, were observed. Extremes of selectivity are shown ranging from the hypoxia selective 64 Cu(II)ATSM to normoxic cell selective 64 Cu(II)GTS. The selectivities observed are compared with the physico chemical characteristics of the complexes. A good correlation exists between selectivity of the complex and its Cu(II)/Cu(I) reduction potential, with hypoxia

  16. Liquid hydrogen and deuterium targets

    International Nuclear Information System (INIS)

    Bougon, M.; Marquet, M.; Prugne, P.

    1961-01-01

    A description is given of 1) Atmospheric pressure target: liquid hydrogen, 400 mm thickness; thermal insulation: styrofoam; the hydrogen vapors are used to improve the target cooling; Mylar windows. 2) Vacuum target: 12 liter content: hydrogen or deuterium; liquid thickness 400 mm; thermal insulation is afforded by a vacuum vessel and a liquid nitrogen shield. Recovery and liquefaction of deuterium vapors are managed in the vacuum vessel which holds the target. The target emptying system is designed for operating in a few minutes. (author) [fr

  17. Isomeric Targets and Beams

    International Nuclear Information System (INIS)

    Oganesyan, Yu.Ts.; Karamyan, S.A.

    1994-01-01

    One of the main topics of modern nuclear physics is the investigation of exotic nuclei including hyper-nuclei, trans fermium elements, proton and neutron rich isotopes near drip lines as well as high-spin excited states and states with anomalous deformation. The isomerism of nuclei is closely related with such phenomena as the alignment of single-particle orbitals, the coexistence of various deformations and the manifestation of intruder-levels from neighbouring shells. The investigation of electromagnetic and nuclear interactions of isomers could give important information on their shell structure and its role in the mechanism of nuclear reactions. For such experiments one can either make isomeric targets (sufficiently long-lived) or use the methods of acceleration of isomeric nuclei. Recently, an exotic 16 + four-quasiparticle isomer of 178 Hf m 2 was produced in a micro weight quantity and the first nuclear reactions on it were successfully observed. The talk describes these experiments as well as new ideas for the continuation of the studies and some advantageous ways for the isomeric beams production by the method of direct acceleration or by the secondary beam method. 35 refs., 15 figs., 8 tabs

  18. EURISOL High Power Targets

    CERN Document Server

    Kadi, Y; Lindroos, M; Ridikas, D; Stora, T; Tecchio, L; CERN. Geneva. BE Department

    2009-01-01

    Modern Nuclear Physics requires access to higher yields of rare isotopes, that relies on further development of the In-flight and Isotope Separation On-Line (ISOL) production methods. The limits of the In-Flight method will be applied via the next generation facilities FAIR in Germany, RIKEN in Japan and RIBF in the USA. The ISOL method will be explored at facilities including ISAC-TRIUMF in Canada, SPIRAL-2 in France, SPES in Italy, ISOLDE at CERN and eventually at the very ambitious multi-MW EURISOL facility. ISOL and in-flight facilities are complementary entities. While in-flight facilities excel in the production of very short lived radioisotopes independently of their chemical nature, ISOL facilities provide high Radioisotope Beam (RIB) intensities and excellent beam quality for 70 elements. Both production schemes are opening vast and rich fields of nuclear physics research. In this article we will introduce the targets planned for the EURISOL facility and highlight some of the technical and safety cha...

  19. Molecularly targeted therapeutic radiopharmaceuticals

    International Nuclear Information System (INIS)

    Saw, M.M.

    2007-01-01

    Full text: It is generally agreed that current focus of nuclear medicine development should be on molecular imaging and therapy. Though, the widespread use of the terminology 'molecular imaging' is quite recent, nuclear medicine has used molecular imaging techniques for more than 20 years ago. A variety of radiopharmaceuticals have been introduced for the internal therapy of malignant and inflammatory lesions in nuclear medicine. In the field of bio/medical imaging, nuclear medicine is one of the disciplines which has the privilege of organized and well developed chemistry/ pharmacy section; radio-chemistry/radiopharmacy. Fundamental principles have been developed more than 40 years ago and advanced research is going well into postgenomic era. The genomic revolution and dramatically increased insight in the molecular mechanisms underlying pathology have led to paradigm shift in drug development. Likewise does in the nuclear medicine. Here, the author will present current clinical and pre-clinical therapeutic radiopharmaceuticals based on molecular targets such as membrane-bound receptors, enzymes, nucleic acids, sodium iodide symporter, etc, in correlation with fundamentals of radiopharmacy. (author)

  20. New type of metal targets

    International Nuclear Information System (INIS)

    Bukharov, A.V.; Ankudinov, V.B.; Ogorodnikov, V.P.; Marukhin, Y.A.

    2014-01-01

    Now the technologies based on interaction of high-intensity beams with substance of a target are being intensively developed. As a target it is possible to use the new type of monodisperse metal targets. The principal advantages of new targets type are: target cooling isn't required; there is no induced activity: the target can be used many times; small dispersion on the speed, the size and interaction points with a beam. The basis of a target is the jet of molten metal, following in the vacuum chamber .Under the influence of the special disturbance superimposed on the liquid jet, the jet disintegrated into identical drops. In the vacuum chamber the drops freeze and form into the solid granules. It is possible to receive monodisperse targets from different metals, alloys and salts (diameter of targets is from 30 .m to 1.5 mm). Dispersion by the sizes and speed is less than 1%. The technique allows to receive not only continuous targets, but also hollow targets with dispersion on thickness of wall within 1...2%.

  1. Using the Nova target chamber for high-yield targets

    International Nuclear Information System (INIS)

    Pitts, J.H.

    1987-01-01

    The existing 2.2-m-radius Nova aluminum target chamber, coated and lined with boron-seeded carbon shields, is proposed for use with 1000-MJ-yield targets in the next laser facility. The laser beam and diagnostic holes in the target chamber are left open and the desired 10 -2 Torr vacuum is maintained both inside and outside the target chamber; a larger target chamber room is the vacuum barrier to the atmosphere. The hole area available is three times that necessary to maintain a maximum fluence below 12 J/cm 2 on optics placed at a radius of 10 m. Maximum stress in the target chamber wall is 73 MPa, which complies with the intent of the ASME Pressure Vessel Code. However, shock waves passing through the inner carbon shield could cause it to comminute. We propose tests and analyses to ensure that the inner carbon shield survives the environment. 13 refs

  2. The target effect: visual memory for unnamed search targets.

    Science.gov (United States)

    Thomas, Mark D; Williams, Carrick C

    2014-01-01

    Search targets are typically remembered much better than other objects even when they are viewed for less time. However, targets have two advantages that other objects in search displays do not have: They are identified categorically before the search, and finding them represents the goal of the search task. The current research investigated the contributions of both of these types of information to the long-term visual memory representations of search targets. Participants completed either a predefined search or a unique-object search in which targets were not defined with specific categorical labels before searching. Subsequent memory results indicated that search target memory was better than distractor memory even following ambiguously defined searches and when the distractors were viewed significantly longer. Superior target memory appears to result from a qualitatively different representation from those of distractor objects, indicating that decision processes influence visual memory.

  3. Immunotherapy Targets in Pediatric Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Orentas, Rimas J.; Lee, Daniel W.; Mackall, Crystal, E-mail: rimas.orentas@nih.gov, E-mail: mackallc@mail.nih.gov [Pediatric Oncology Branch, National Cancer Institute, National Institutes of Health, Bethesda, MD (United States)

    2012-01-30

    Immunotherapy for cancer has shown increasing success and there is ample evidence to expect that progress gleaned in immune targeting of adult cancers can be translated to pediatric oncology. This manuscript reviews principles that guide selection of targets for immunotherapy of cancer, emphasizing the similarities and distinctions between oncogene-inhibition targets and immune targets. It follows with a detailed review of molecules expressed by pediatric tumors that are already under study as immune targets or are good candidates for future studies of immune targeting. Distinctions are made between cell surface antigens that can be targeted in an MHC independent manner using antibodies, antibody derivatives, or chimeric antigen receptors versus intracellular antigens which must be targeted with MHC restricted T cell therapies. Among the most advanced immune targets for childhood cancer are CD19 and CD22 on hematologic malignancies, GD2 on solid tumors, and NY-ESO-1 expressed by a majority of synovial sarcomas, but several other molecules reviewed here also have properties which suggest that they too could serve as effective targets for immunotherapy of childhood cancer.

  4. Immunotherapy Targets in Pediatric Cancer

    International Nuclear Information System (INIS)

    Orentas, Rimas J.; Lee, Daniel W.; Mackall, Crystal

    2012-01-01

    Immunotherapy for cancer has shown increasing success and there is ample evidence to expect that progress gleaned in immune targeting of adult cancers can be translated to pediatric oncology. This manuscript reviews principles that guide selection of targets for immunotherapy of cancer, emphasizing the similarities and distinctions between oncogene-inhibition targets and immune targets. It follows with a detailed review of molecules expressed by pediatric tumors that are already under study as immune targets or are good candidates for future studies of immune targeting. Distinctions are made between cell surface antigens that can be targeted in an MHC independent manner using antibodies, antibody derivatives, or chimeric antigen receptors versus intracellular antigens which must be targeted with MHC restricted T cell therapies. Among the most advanced immune targets for childhood cancer are CD19 and CD22 on hematologic malignancies, GD2 on solid tumors, and NY-ESO-1 expressed by a majority of synovial sarcomas, but several other molecules reviewed here also have properties which suggest that they too could serve as effective targets for immunotherapy of childhood cancer.

  5. [Target volume margins for lung cancer: internal target volume/clinical target volume].

    Science.gov (United States)

    Jouin, A; Pourel, N

    2013-10-01

    The aim of this study was to carry out a review of margins that should be used for the delineation of target volumes in lung cancer, with a focus on margins from gross tumour volume (GTV) to clinical target volume (CTV) and internal target volume (ITV) delineation. Our review was based on a PubMed literature search with, as a cornerstone, the 2010 European Organisation for Research and Treatment of Cancer (EORTC) recommandations by De Ruysscher et al. The keywords used for the search were: radiotherapy, lung cancer, clinical target volume, internal target volume. The relevant information was categorized under the following headings: gross tumour volume definition (GTV), CTV-GTV margin (first tumoural CTV then nodal CTV definition), in field versus elective nodal irradiation, metabolic imaging role through the input of the PET scanner for tumour target volume and limitations of PET-CT imaging for nodal target volume definition, postoperative radiotherapy target volume definition, delineation of target volumes after induction chemotherapy; then the internal target volume is specified as well as tumoural mobility for lung cancer and respiratory gating techniques. Finally, a chapter is dedicated to planning target volume definition and another to small cell lung cancer. For each heading, the most relevant and recent clinical trials and publications are mentioned. Copyright © 2013. Published by Elsevier SAS.

  6. Facility target insert shielding assessment

    Energy Technology Data Exchange (ETDEWEB)

    Mocko, Michal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-06

    Main objective of this report is to assess the basic shielding requirements for the vertical target insert and retrieval port. We used the baseline design for the vertical target insert in our calculations. The insert sits in the 12”-diameter cylindrical shaft extending from the service alley in the top floor of the facility all the way down to the target location. The target retrieval mechanism is a long rod with the target assembly attached and running the entire length of the vertical shaft. The insert also houses the helium cooling supply and return lines each with 2” diameter. In the present study we focused on calculating the neutron and photon dose rate fields on top of the target insert/retrieval mechanism in the service alley. Additionally, we studied a few prototypical configurations of the shielding layers in the vertical insert as well as on the top.

  7. Inertial-confinement-fusion targets

    International Nuclear Information System (INIS)

    Hendricks, C.D.

    1981-01-01

    Inertial confinement fusion (ICF) targets are made as simple flat discs, as hollow shells or as complicated multilayer structures. Many techniques have been devised for producing the targets. Glass and metal shells are made by using drop and bubble techniques. Solid hydrogen shells are also produced by adapting old methods to the solution of modern problems. Some of these techniques, problems and solutions are discussed. In addition, the applications of many of the techniques to fabrication of ICF targets is presented

  8. Targeted Nanotechnology for Cancer Imaging

    Science.gov (United States)

    Toy, Randall; Bauer, Lisa; Hoimes, Christopher; Ghaghada, Ketan B.; Karathanasis, Efstathios

    2014-01-01

    Targeted nanoparticle imaging agents provide many benefits and new opportunities to facilitate accurate diagnosis of cancer and significantly impact patient outcome. Due to the highly engineerable nature of nanotechnology, targeted nanoparticles exhibit significant advantages including increased contrast sensitivity, binding avidity and targeting specificity. Considering the various nanoparticle designs and their adjustable ability to target a specific site and generate detectable signals, nanoparticles can be optimally designed in terms of biophysical interactions (i.e., intravascular and interstitial transport) and biochemical interactions (i.e., targeting avidity towards cancer-related biomarkers) for site-specific detection of very distinct microenvironments. This review seeks to illustrate that the design of a nanoparticle dictates its in vivo journey and targeting of hard-to-reach cancer sites, facilitating early and accurate diagnosis and interrogation of the most aggressive forms of cancer. We will report various targeted nanoparticles for cancer imaging using X-ray computed tomography, ultrasound, magnetic resonance imaging, nuclear imaging and optical imaging. Finally, to realize the full potential of targeted nanotechnology for cancer imaging, we will describe the challenges and opportunities for the clinical translation and widespread adaptation of targeted nanoparticles imaging agents. PMID:25116445

  9. Target imaging and backlighting diagnosis

    International Nuclear Information System (INIS)

    Yaakobi, B.; Shvarts, D.; Marshall, F.J.; Epstein, R.; Su, Q.

    1995-01-01

    The expected backlighting and self-emission images of a particular CH target to be imploded on the Omega Upgrade are calculated for a variety of experimental parameters. It is shown that to overcome the problem of target self-emission, the image has to be monochromatized with a diffracting crystal. For the target studied, the two image components are then comparable in intensity and both provide useful information on target behavior. A particularly interesting feature is the appearance in the self-emission of a circular spike which closely delineates the fuel-shell interface, but requires high spatial resolution to be observed

  10. Literature evidence in open targets - a target validation platform.

    Science.gov (United States)

    Kafkas, Şenay; Dunham, Ian; McEntyre, Johanna

    2017-06-06

    We present the Europe PMC literature component of Open Targets - a target validation platform that integrates various evidence to aid drug target identification and validation. The component identifies target-disease associations in documents and ranks the documents based on their confidence from the Europe PMC literature database, by using rules utilising expert-provided heuristic information. The confidence score of a given document represents how valuable the document is in the scope of target validation for a given target-disease association by taking into account the credibility of the association based on the properties of the text. The component serves the platform regularly with the up-to-date data since December, 2015. Currently, there are a total number of 1168365 distinct target-disease associations text mined from >26 million PubMed abstracts and >1.2 million Open Access full text articles. Our comparative analyses on the current available evidence data in the platform revealed that 850179 of these associations are exclusively identified by literature mining. This component helps the platform's users by providing the most relevant literature hits for a given target and disease. The text mining evidence along with the other types of evidence can be explored visually through https://www.targetvalidation.org and all the evidence data is available for download in json format from https://www.targetvalidation.org/downloads/data .

  11. Internal Targeting and External Control: Phototriggered Targeting in Nanomedicine.

    Science.gov (United States)

    Arrue, Lily; Ratjen, Lars

    2017-12-07

    The photochemical control of structure and reactivity bears great potential for chemistry, biology, and life sciences. A key feature of photochemistry is the spatiotemporal control over secondary events. Well-established applications of photochemistry in medicine are photodynamic therapy (PDT) and photopharmacology (PP). However, although both are highly localizable through the application of light, they lack cell- and tissue-specificity. The combination of nanomaterial-based drug delivery and targeting has the potential to overcome limitations for many established therapy concepts. Even more privileged seems the merger of nanomedicine and cell-specific targeting (internal targeting) controlled by light (external control), as it can potentially be applied to many different areas of medicine and pharmaceutical research, including the aforementioned PDT and PP. In this review a survey of the interface of photochemistry, medicine and targeted drug delivery is given, especially focusing on phototriggered targeting in nanomedicine. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Radiopharmaceuticals targeting melanoma

    Energy Technology Data Exchange (ETDEWEB)

    Pham, T.Q.; Berghofer, P.; Liu, X.; Greguric, I.; Dikic, B.; Ballantyne, P.; Mattner, F.; Nguyen, V.; Loc' h, C.; Katsifis, A. [Radiopharmaceuticals Research Institute, Australian Nuclear Science and Technology Organisation, Menai, N.S.W., Sydney (Australia)

    2008-02-15

    Melanoma is one of the most aggressive cancers known with a high rate of mortality and increasing global incidence. So, the development of radiopharmaceuticals for either diagnostic or therapeutic purposes could make enormous contributions to melanoma patient health care. We have been studying melanoma tumours through several targeting mechanisms including melanin or specific receptor based radiopharmaceuticals Structure activity studies indicate that the substitution patterns on radioiodinated benzamides significantly influence the uptake mechanism from melanin to sigma-receptor binding. Furthermore, the position of the iodine as well as the presence of key functional groups and substituents has resulted in compounds with varying degrees of activity uptake and retention in tumours. From these results, a novel molecule 2-(2-(4-(4-iodo benzyl)piperazin-1-yl)-2-oxo-ethyl)isoindoline- 1,3-dione (M.E.L.037) was synthesized, labelled with iodine-123 and evaluated for application in melanoma tumour scintigraphy and radiotherapy. The tumour imaging potential of {sup 123}IM.E.L.037 was studied in vivo in C.57 B.L./ 6 J female mice bearing the B.16 F.0. murine melanoma tumour and in BALB/c nude mice bearing the A.375 human amelanotic melanoma tumour by biodistribution, competition studies and by SPECT imaging. {sup 123}I-M.E.L.037 exhibited high and rapid uptake in the B.16 F.0 melanoma tumour at 1 h (13 % I.D./g) increasing with time to reach 25 % I.D./g at 6 h. A significant uptake was also observed in the eyes (2% I.D., at 3-6 h p.i.) of black mice. No uptake was observed in the tumour or in the eyes of nude mice bearing the A.375 tumour. Due to high uptake and long retention in the tumour and rapid body clearance, standardized uptake values(S.U.V.) of {sup 123}I-M.E.L.037 were 30 and 60, at 24 and 48 h p.i.,respectively. SPECT imaging of mice bearing the B.16 melanoma indicated the radioactivity was predominately located in the tumour followed by the eyes, while no

  13. Target support for inertial confinement fusion

    International Nuclear Information System (INIS)

    Schultz, K.R.

    1995-08-01

    General Atomics (GA) plays an important industrial support role for the US Inertial Confinement Fusion (ICF) program in the area of target technology. This includes three major activities: target fabrication support, target handling systems development, and target chamber design. The work includes target fabrication for existing ICF experiments, target and target system development for future experiments, and target research and target chamber design for experiments on future machines, such as the National Ignition Facility (NIF)

  14. Target recognition by wavelet transform

    International Nuclear Information System (INIS)

    Li Zhengdong; He Wuliang; Zheng Xiaodong; Cheng Jiayuan; Peng Wen; Pei Chunlan; Song Chen

    2002-01-01

    Wavelet transform has an important character of multi-resolution power, which presents pyramid structure, and this character coincides the way by which people distinguish object from coarse to fineness and from large to tiny. In addition to it, wavelet transform benefits to reducing image noise, simplifying calculation, and embodying target image characteristic point. A method of target recognition by wavelet transform is provided

  15. High performance inertial fusion targets

    International Nuclear Information System (INIS)

    Nuckolls, J.H.; Bangerter, R.O.; Lindl, J.D.; Mead, W.C.; Pan, Y.L.

    1978-01-01

    Inertial confinement fusion (ICF) target designs are considered which may have very high gains (approximately 1000) and low power requirements (< 100 TW) for input energies of approximately one megajoule. These include targets having very low density shells, ultra thin shells, central ignitors, magnetic insulation, and non-ablative acceleration

  16. Treating rheumatoid arthritis to target

    DEFF Research Database (Denmark)

    Smolen, Josef S; Breedveld, Ferdinand C; Burmester, Gerd R

    2016-01-01

    BACKGROUND: Reaching the therapeutic target of remission or low-disease activity has improved outcomes in patients with rheumatoid arthritis (RA) significantly. The treat-to-target recommendations, formulated in 2010, have provided a basis for implementation of a strategic approach towards this t...

  17. Spinning targets for laser fusion

    International Nuclear Information System (INIS)

    Baldwin, D.E.; Ryutov, D.D.

    1995-09-01

    Several techniques for spinning the ICF targets up prior to or in the course of their compression are suggested. Interference of the rotational shear flow with Rayleigh-Taylor instability is briefly discussed and possible consequences for the target performance are pointed out

  18. Multiple Target Laser Designator (MTLD)

    Science.gov (United States)

    2007-03-01

    Optimized Liquid Crystal Scanning Element Optimize the Nonimaging Predictive Algorithm for Target Ranging, Tracking, and Position Estimation...commercial potential. 3.0 PROGRESS THIS QUARTER 3.1 Optimization of Nonimaging Holographic Antenna for Target Tracking and Position Estimation (Task 6) In

  19. Scheduling with target start times

    NARCIS (Netherlands)

    Hoogeveen, J.A.; Velde, van de S.L.; Klein Haneveld, W.K.; Vrieze, O.J.; Kallenberg, L.C.M.

    1997-01-01

    We address the single-machine problem of scheduling n independent jobs subject to target start times. Target start times are essentially release times that may be violated at a certain cost. The goal is to minimize an objective function that is composed of total completion time and maximum

  20. Optimum target thickness for polarimeters

    International Nuclear Information System (INIS)

    Sitnik, I.M.

    2003-01-01

    Polarimeters with thick targets are a tool to measure the proton polarization. But the question about the optimum target thickness is still the subject of discussion. An attempt to calculate the most common parameters concerning this problem, in a few GeV region, is made

  1. Target-Searching on Percolation

    International Nuclear Information System (INIS)

    Yang Shijie

    2005-01-01

    We study target-searching processes on a percolation, on which a hunter tracks a target by smelling odors it emits. The odor intensity is supposed to be inversely proportional to the distance it propagates. The Monte Carlo simulation is performed on a 2-dimensional bond-percolation above the threshold. Having no idea of the location of the target, the hunter determines its moves only by random attempts in each direction. For lager percolation connectivity p ∼> 0.90, it reveals a scaling law for the searching time versus the distance to the position of the target. The scaling exponent is dependent on the sensitivity of the hunter. For smaller p, the scaling law is broken and the probability of finding out the target significantly reduces. The hunter seems trapped in the cluster of the percolation and can hardly reach the goal.

  2. Targeted marketing and public health.

    Science.gov (United States)

    Grier, Sonya A; Kumanyika, Shiriki

    2010-01-01

    Targeted marketing techniques, which identify consumers who share common needs or characteristics and position products or services to appeal to and reach these consumers, are now the core of all marketing and facilitate its effectiveness. However, targeted marketing, particularly of products with proven or potential adverse effects (e.g., tobacco, alcohol, entertainment violence, or unhealthful foods) to consumer segments defined as vulnerable raises complex concerns for public health. It is critical that practitioners, academics, and policy makers in marketing, public health, and other fields recognize and understand targeted marketing as a specific contextual influence on the health of children and adolescents and, for different reasons, ethnic minority populations and other populations who may benefit from public health protections. For beneficial products, such understanding can foster more socially productive targeting. For potentially harmful products, understanding the nature and scope of targeted marketing influences will support identification and implementation of corrective policies.

  3. The Bering Target Tracking Instrumentation

    DEFF Research Database (Denmark)

    Denver, Troelz; Jørgensen, John Leif; Betto, Maurizio

    2003-01-01

    The key science instrument on the Bering satellite mission is a relative small telescope with an entrance aperture of 300 mm and a focal length between 500 and 1000 mm. The detection of potential targets is performed by one of the target scanning advanced stellar compasses (ASCs). This procedure...... results in a simple prioritized list of right ascension, declination, proper motion and intensity of each prospective target. The telescope itself has a dedicated ASC Camera Head Unit (CHU) mounted on the secondary mirror, largely co-aligned with the telescope. This CHU accurately determines the telescope......'s pointing direction. To achieve fast tracking over a large solid angle, the telescope pointing is achieved by means of a folding mirror in the optical pathway. When a prospective target approaches the telescope FOV, the ASC on the secondary will guide the folding mirror into position such that the target...

  4. Legal Issues in Cyber Targeting

    DEFF Research Database (Denmark)

    Juhlin, Jonas Alastair

    Imagine this scenario: Two states are in armed conflict with each other. In order to gain an advantage, one side launches a cyber-attack against the opponent’s computer network. The malicious malware paralyze the military computer network, as intended, but the malware spreads into the civilian...... system with physical damage to follow. This can happen and the natural question arises: What must be considered lawful targeting according to the international humanitarian law in cyber warfare? What steps must an attacker take to minimize the damage done to unlawful targets when conducting an offensive...... operation? How can the attacker separate military targets from civilian targets in cyber space? This paper addresses these questions and argues that a network (civilian or military) consist of several software components and that it is the individual components that is the target. If the components are used...

  5. Gas target neutron generator studies

    International Nuclear Information System (INIS)

    Chatoorgoon, V.

    1978-01-01

    The need for an intense neutron source for the study of radiation damage on materials has resulted in the proposal of various solid, liquid, and gas targets. Among the gas targets proposed have been the transonic gas target, two types of hypersonic gas target, and the subsonic gas target (SGT). It has been suggested that heat deposition in a subsonic channel might create a gas density step which would constitute an attractive gas target type. The first part of the present study examines this aspect of the SGT and shows that gas density gradients are indeed formed by heat deposition in subsonic flow. The variation of beam voltage, gas density, gas pressure, and gas temperature within the channel have been calculated as functions of the system parameters: beam voltage, beam current, channel diameter, stagnation tank temperature and pressure. The analysis is applicable to any beam particle and target gas. For the case of T + on D 2 , which is relevant to the fusion application, the 14 MeV neutron profiles are presented as a function of system parameters. It is found that the SGT is compatible with concentrated intense source operation. The possibility of instability was investigated in detail using a non-linear analysis which made it possible to follow the complete time development of the SGT. It was found that the SGT is stable against all small perturbations and certain types of large perturbations. It appears that the SGT is the most advantageous type of gas target, operating at a lower mass flow and less severe stagnation tank conditions than the other types. The second part of the thesis examines a problem associated with the straight hypersonic target, the deuterium spill into the tritium port. The regime of practical operation for this target is established. (auth)

  6. Preparation of thin nuclear targets

    International Nuclear Information System (INIS)

    Muggleton, A.H.F.

    1979-03-01

    Thin film backings, sources and targets are needed for many applications in low energy nuclear physics and nuclear chemistry experiments. A survey of techniques used in the preparation of nuclear targets is first briefly discussed. These are classified as chemical, mechanical and physical preparations. Vacuum evaporation, being the most generally used technique, is discussed in detail. It is highly desirable to monitor the film thickness and control the deposition rate during evaporation and to measure the final target thickness after deposition has concluded. The relative merits of various thickness measuring techniques are described. Stages in the fabrication and mounting of self-supporting foils are described in detail, with emphasis given to the preparation of thin self-supporting carbon foils used as target backings and stripper foils. Various target backings, and the merits of the more generally used release agents are described in detail. The preparations of more difficult elemental targets are discussed, and a comprehensive list of the common targets is presented

  7. Spallation source neutron target systems

    International Nuclear Information System (INIS)

    Russell, G.; Brown, R.; Collier, M.; Donahue, J.

    1996-01-01

    This is the final report for a two-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The project sought to design a next-generation spallation source neutron target system for the Manuel Lujan, Jr., Neutron Scattering Center (LANSCE) at Los Alamos. It has been recognized for some time that new advanced neutron sources are needed in the US if the country is to maintain a competitive position in several important scientific and technological areas. A recent DOE panel concluded that the proposed Advanced Neutron Source (a nuclear reactor at Oak Ridge National Laboratory) and a high-power pulsed spallation source are both needed in the near future. One of the most technically challenging designs for a spallation source is the target station itself and, more specifically, the target-moderator-reflector arrangement. Los Alamos has demonstrated capabilities in designing, building, and operating high-power spallation-neutron-source target stations. Most of the new design ideas proposed worldwide for target system design for the next generation pulsed spallation source have either been conceived and implemented at LANSCE or proposed by LANSCE target system designers. These concepts include split targets, flux-trap moderators, back scattering and composite moderators, and composite reflectors

  8. Simulations of effusion from ISOL target/ion source systems

    International Nuclear Information System (INIS)

    Mustapha, B.; Nolen, J.A.

    2004-01-01

    Monte Carlo simulations of the low- and high-conductivity Target/Ion Source systems used at Oak Ridge National Laboratory for effusion measurements are performed. Comparisons with the corresponding experimental data for the different geometries are presented and discussed. Independent checks of the simulation using data for simple geometries and using the conductance approach well known in vacuum technology are performed. A simulation-based comparison between the low- and high-conductivity systems is also presented

  9. PENETAPAN TARGET TERHADAP STICKINESS COST

    Directory of Open Access Journals (Sweden)

    Windyastuti Windyastuti

    2017-03-01

    Full Text Available This study aimed to analyze the influence of manager targeting to the stickiness cost. The research data was amanufacturing company’s financial statements during 1999-2011 published at BEI. The research data includedcost of sales, administration and general, net sales and Price Earnings Ratio (PER. This study used adynamic panel data regression analysis. The results showed that cost of sales, administration and general weresticky. Furthermore, manager targeting caused the stickiness degree of sales, administration and general costlower. Manager targeting changed the manager’s behavior. When the net sales declined, manager reduced theresource use drastically so the cost of sales, administration and general also decreased drastically.

  10. Development of targeted radiotherapy systems

    International Nuclear Information System (INIS)

    Ferro, Guillermina; Villarreal, Jose E.; Garcia, Laura; Tendilla, Jose I.; Paredes, Lydia; Murphy, Consuelo A.; Pedraza, Martha

    2001-01-01

    Conventional or external beam radiotherapy, has been a viable alternative for cancer treatment. Although this technique is effective, its use is limited if the patient has multiple malignant lesions (metastases). An alternative approach is based on the design of radiopharmaceuticals that, to be administered in the patient, are directed specifically toward the target cell producing a selective radiation delivery. This treatment is known as targeted radiotherapy. We have summarized and discussed some results related to our investigations on the development of targeted radiotherapy systems, including aspects of internal dosimetry

  11. Treating rheumatoid arthritis to target

    DEFF Research Database (Denmark)

    Smolen, Josef S; Aletaha, Daniel; Bijlsma, Johannes W J

    2010-01-01

    BACKGROUND: Aiming at therapeutic targets has reduced the risk of organ failure in many diseases such as diabetes or hypertension. Such targets have not been defined for rheumatoid arthritis (RA). OBJECTIVE: /st> To develop recommendations for achieving optimal therapeutic outcomes in RA. METHODS....... Levels of evidence, strength of recommendations and levels of agreement were derived. RESULTS: The treat-to-target activity resulted in 10 recommendations. The treatment aim was defined as remission with low disease activity being an alternative goal in patients with long-standing disease. Regular follow...

  12. A Cryogenic Infrared Calibration Target

    Science.gov (United States)

    Wollack, E. J.; Kinzer, R. E., Jr.; Rinehart, S. A.

    2014-01-01

    A compact cryogenic calibration target is presented that has a peak diffuse reflectance, R target. The resulting target assembly is lightweight, has a low-geometric profile, and has survived repeated thermal cycling from room temperature to approx.4 K. Basic design considerations, governing equations, and test data for realizing the structure described are provided. The optical properties of selected absorptive materials-Acktar Fractal Black, Aeroglaze Z306, and Stycast 2850 FT epoxy loaded with stainless steel powder-are characterized and presented

  13. Obstacles to Effective Joint Targeting

    National Research Council Canada - National Science Library

    Patch, John

    2007-01-01

    .... Notwithstanding the most precise and capable weaponry ever, any targeting effort absent coherent strategy or executed outside the art and rules of war can spell campaign defeat even amidst tactical successes...

  14. Immunotherapy Targets Common Cancer Mutation

    Science.gov (United States)

    In a study of an immune therapy for colorectal cancer that involved a single patient, researchers identified a method for targeting the cancer-causing protein produced by a mutant form of the KRAS gene.

  15. Tracking Target and Spiral Waves

    DEFF Research Database (Denmark)

    Jensen, Flemming G.; Sporring, Jon; Nielsen, Mads

    2002-01-01

    A new algorithm for analyzing the evolution of patterns of spiral and target waves in large aspect ratio chemical systems is introduced. The algorithm does not depend on finding the spiral tip but locates the center of the pattern by a new concept, called the spiral focus, which is defined...... by the evolutes of the actual spiral or target wave. With the use of Gaussian smoothing, a robust method is developed that permits the identification of targets and spirals foci independently of the wave profile. Examples of an analysis of long image sequences from experiments with the Belousov......–Zhabotinsky reaction catalyzed by ruthenium-tris-bipyridyl are presented. Moving target and spiral foci are found, and the speed and direction of movement of single as well as double spiral foci are investigated. For the experiments analyzed in this paper it is found that the movement of a focus correlates with foci...

  16. Obstacles to Effective Joint Targeting

    National Research Council Canada - National Science Library

    Patch, John

    2007-01-01

    No foe can beat the modern-day American military machine in combined arms warfare, yet this machine is subject to strategic targeting vulnerabilities that military and policy leaders would do well to appreciate...

  17. Vascular targeting with peptide libraries

    Energy Technology Data Exchange (ETDEWEB)

    Pasqualini, R. [La Jolla Cancer Research Center The Burnham Inst., La Jolla CA (United States)

    1999-06-01

    The authors have developed an 'in vivo' selection system in which phage capable of selective homing to different tissues are recovered from a phage display peptide library following intravenous administration. Using this strategy, they have isolate several organ and tumor-homing peptides. They have shown that each of those peptides binds of different receptors that are selectively expressed on the vasculature of the target tissue. The tumor-homing peptides bind to receptors that are up regulated in tumor angiogenic vasculature. Targeted delivery of doxorubicin to angiogenic vasculature using these peptides in animals models decrease toxicity and increased the therapeutic efficacy of the drug. Vascular targeting may facilitate the development of other treatment strategies that rely on inhibition of angio genesis and lead to advances to extend the potential for targeting of drugs, genes and radionuclides in the context of many diseases.

  18. Navy Advertising: Targeting Generation Z

    Science.gov (United States)

    2015-12-01

    NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA MBA PROFESSIONAL REPORT NAVY ADVERTISING : TARGETING GENERATION Z December......study recommends improvements for Navy advertising efficiency by examining characteristics of recruits defined as Generation Z. Data gathered from five

  19. Physics of Automatic Target Recognition

    CERN Document Server

    Sadjadi, Firooz

    2007-01-01

    Physics of Automatic Target Recognition addresses the fundamental physical bases of sensing, and information extraction in the state-of-the art automatic target recognition field. It explores both passive and active multispectral sensing, polarimetric diversity, complex signature exploitation, sensor and processing adaptation, transformation of electromagnetic and acoustic waves in their interactions with targets, background clutter, transmission media, and sensing elements. The general inverse scattering, and advanced signal processing techniques and scientific evaluation methodologies being used in this multi disciplinary field will be part of this exposition. The issues of modeling of target signatures in various spectral modalities, LADAR, IR, SAR, high resolution radar, acoustic, seismic, visible, hyperspectral, in diverse geometric aspects will be addressed. The methods for signal processing and classification will cover concepts such as sensor adaptive and artificial neural networks, time reversal filt...

  20. Inertial-confinement-fusion targets

    International Nuclear Information System (INIS)

    Hendricks, C.D.

    1982-01-01

    Much of the research in laser fusion has been done using simple ball on-stalk targets filled with a deuterium-tritium mixture. The targets operated in the exploding pusher mode in which the laser energy was delivered in a very short time (approx. 100 ps or less) and was absorbed by the glass wall of the target. The high energy density in the glass literally exploded the shell with the inward moving glass compressing the DT fuel to high temperatures and moderate densities. Temperatures achieved were high enough to produce DT reactions and accompanying thermonuclear neutrons and alpha particles. The primary criteria imposed on the target builders were: (1) wall thickness, (2) sphere diameter, and (3) fuel in the sphere

  1. Targeted intraoperative radiotherapy in oncology

    CERN Document Server

    Keshtgar, Mohammed; Wenz, Frederik

    2014-01-01

    Targeted intraoperative radiotherapy is a major advance in the management of cancer patients. With an emphasis on practical aspects, this book offers an ideal introduction to this innovative  technology for clinicians.

  2. Special hydrogen target (Prop. 210)

    International Nuclear Information System (INIS)

    Halliday, C.E.

    1979-11-01

    This guide contains a description of the electrical control and automatic vacuum systems for the Special Hydrogen Target (Prop. 210) together with the flow diagram and the mimic control panel layout for the system. (U.K.)

  3. National Ignition Facility Target Chamber

    International Nuclear Information System (INIS)

    Wavrik, R W; Cox, J R; Fleming, P J

    2000-01-01

    On June 11, 1999 the Department of Energy dedicated the single largest piece of the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) in Livermore, California. The ten (10) meter diameter aluminum target high vacuum chamber will serve as the working end of the largest laser in the world. The output of 192 laser beams will converge at the precise center of the chamber. The laser beams will enter the chamber in two by two arrays to illuminate 10 millimeter long gold cylinders called hohlraums enclosing 2 millimeter capsule containing deuterium, tritium and isotopes of hydrogen. The two isotopes will fuse, thereby creating temperatures and pressures resembling those found only inside stars and in detonated nuclear weapons, but on a minute scale. The NIF Project will serve as an essential facility to insure safety and reliability of our nation's nuclear arsenal as well as demonstrating inertial fusion's contribution to creating electrical power. The paper will discuss the requirements that had to be addressed during the design, fabrication and testing of the target chamber. A team from Sandia National Laboratories (SNL) and LLNL with input from industry performed the configuration and basic design of the target chamber. The method of fabrication and construction of the aluminum target chamber was devised by Pitt-Des Moines, Inc. (PDM). PDM also participated in the design of the chamber in areas such as the Target Chamber Realignment and Adjustment System, which would allow realignment of the sphere laser beams in the event of earth settlement or movement from a seismic event. During the fabrication of the target chamber the sphericity tolerances had to be addressed for the individual plates. Procedures were developed for forming, edge preparation and welding of individual plates. Construction plans were developed to allow the field construction of the target chamber to occur parallel to other NIF construction activities. This was

  4. Theoretical aspects of inflation targeting

    Directory of Open Access Journals (Sweden)

    Obradović Jelena

    2014-01-01

    Full Text Available Inflation targeting is one of the possible strategies used by central banks during conducting monetary policy. The basic characteristics, advantages and disadvantages of inflation targeting will be presented in this paper. The focus is on the the presentation and interpretation of the understanding of this strategy from the perspective of monetarist and Keynesian theory, the theory of rational expectations, and methodological analysis of the strategy in light of the game theory using payoff matrix.

  5. Targeting Splicing in Prostate Cancer

    OpenAIRE

    Effrosyni Antonopoulou; Michael Ladomery

    2018-01-01

    Over 95% of human genes are alternatively spliced, expressing splice isoforms that often exhibit antagonistic functions. We describe genes whose alternative splicing has been linked to prostate cancer; namely VEGFA, KLF6, BCL2L2, ERG, and AR. We discuss opportunities to develop novel therapies that target specific splice isoforms, or that target the machinery of splicing. Therapeutic approaches include the development of small molecule inhibitors of splice factor kinases, splice isoform speci...

  6. Targeting BRCAness in Gastric Cancer

    Science.gov (United States)

    2017-10-01

    Award Number: W81XWH-16-1-0472 TITLE: Targeting BRCAness in Gastric Cancer PRINCIPAL INVESTIGATOR: Lawrence Fong CONTRACTING ORGANIZATION...Targeting BRCAness in Gastric Cancer 5b. GRANT NUMBER W81XWH-16-1-0473 (Ashworth) 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Eric Collisson, David Quigley...for Public Release; Distribution Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT We performed the screen of gastric cancer cell lines for their

  7. Targeting Quiescence in Prostate Cancer

    Science.gov (United States)

    2017-10-01

    AWARD NUMBER: W81XWH-15-1-0413 TITLE: Targeting Quiescence in Prostate Cancer PRINCIPAL INVESTIGATOR: Laura Buttitta CONTRACTING...Quiescence in Prostate Cancer 5a. CONTRACT NUMBER Targeting uiescence in Prostate Cancer 5b. GRANT NUMBER W81XWH-15-1-0413 5c. PROGRAM ELEMENT NUMBER 6...NOTES 14. ABSTRACT A major problem in prostate cancer is finding and eliminating the non-proliferating or “quiescent” cancer cells. This is because early

  8. Targeting BRCAness in Gastric Cancer

    Science.gov (United States)

    2017-10-01

    Award Number: W81XWH-16-1-0470 TITLE: Targeting BRCAness in Gastric Cancer PRINCIPAL INVESTIGATOR: Yelena Janjigian CONTRACTING ORGANIZATION...Sloan-Kettering Institute for Cancer Research New York, NY 10065 REPORT DATE: October 2017 TYPE OF REPORT: Annual PREPARED FOR: U.S. Army Medical...Targeting BRCAness in Gastric Cancer 5b. GRANT NUMBER W81XWH-16-1-0473 (Ashworth) 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Eric Collisson, David

  9. Gas target with thin wall

    International Nuclear Information System (INIS)

    Korenchenko, A.S.; Korenchenko, S.M.; Kravchuk, N.P.; Filippov, A.I.; Fursov, A.P.

    1992-01-01

    The technology of targets manufacture with thin wall diameter 100 mm and lengthwise 700 mm from composition kevlar + epoxy resin is described. The test's results on pressure and vacuum are reported. The created targets are supposed to be used on the installation ARES for an investigation of muons and pions interactions with light nuclei and rare pions decay 'on flying'. 5 refs.; 2 figs.; 2 tabs

  10. Targeted immunotherapy in Hodgkin lymphoma

    DEFF Research Database (Denmark)

    Hutchings, Martin

    2015-01-01

    In this issue of Blood, Rothe et al introduce a new principle of targeted Hodgkin lymphoma (HL) immunotherapy in their report from a phase 1 study of the bispecific anti-CD30/CD16A antibody construct AFM13.......In this issue of Blood, Rothe et al introduce a new principle of targeted Hodgkin lymphoma (HL) immunotherapy in their report from a phase 1 study of the bispecific anti-CD30/CD16A antibody construct AFM13....

  11. X-ray tube target

    International Nuclear Information System (INIS)

    Weber, R.G.

    1980-01-01

    A target with an improved heat emissive surface for use in a rotating anode type x-ray tube is described. The target consists of a body having a first surface portion made of x-ray emissive material and a second surface portion made of a heat emissive material comprising at least one of hafnium boride, hafnium oxide, hafnium nitride, hafnium silicide, and hafnium aluminide. (U.K.)

  12. Polarized atomic beams for targets

    International Nuclear Information System (INIS)

    Grueebler, W.

    1984-01-01

    The basic principle of the production of polarized atomic hydrogen and deuterium beams are reviewed. The status of the present available polarization, density and intensity are presented. The improvement of atomic beam density by cooling the hydrogen atoms to low velocity is discussed. The possible use of polarized atomic beams as targets in storage rings is shown. It is proposed that polarized atomic beams can be used to produce polarized gas targets with high polarization and greatly improved density

  13. Market segmentation, targeting and positioning

    OpenAIRE

    Camilleri, Mark Anthony

    2017-01-01

    Businesses may not be in a position to satisfy all of their customers, every time. It may prove difficult to meet the exact requirements of each individual customer. People do not have identical preferences, so rarely does one product completely satisfy everyone. Many companies may usually adopt a strategy that is known as target marketing. This strategy involves dividing the market into segments and developing products or services to these segments. A target marketing strategy is focused on ...

  14. Theranostics Targeting Metastatic Breast Cancer

    Science.gov (United States)

    2016-10-01

    Knapp DW. Targeting folate receptors to treat invasive urinary bladder cancer . Cancer Res 2013;73(2):875–884. 71. Holm J, Hansen SI, Hoier-Madsen M...purpose of this review, active targeting in cancer research encompasses strategies wherein a ligand for a cell surface receptor expressed on tumor...trafficking, thus impacting the efficacy of receptor -mediated drug delivery for cancer therapy. These factors include the following: (i) the rate of ligand

  15. Target-oriented chaos control

    International Nuclear Information System (INIS)

    Dattani, Justine; Blake, Jack C.H.; Hilker, Frank M.

    2011-01-01

    Designing intervention methods to control chaotic behavior in dynamical systems remains a challenging problem, in particular for systems that are difficult to access or to measure. We propose a simple, intuitive technique that modifies the values of the state variables directly toward a certain target. The intervention takes into account the difference to the target value, and is a combination of traditional proportional feedback and constant feedback methods. It proves particularly useful when the target corresponds to the equilibrium of the uncontrolled system, and is available or can be estimated from expert knowledge (e.g. in biology and economy). -- Highlights: → We propose a chaos control method that forces the system to a certain target. → The intervention takes into account the difference to the target value. → It can be seen as a combination of proportional and constant feedback methods. → The method is very robust and highly efficient in the long-term. → It is particularly applicable when suitable target values are known or available.

  16. Target cells in internal dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Goessner, W

    2003-07-01

    Data related to radium induced bone sarcomas in humans are used as a model for defining target cells on bone surfaces and in the bone marrow. The differential distribution of radiation induced bone sarcoma types with a high ratio of non-bone producing, mainly fibroblastic tumours, challenges the ICRP concept that the bone lining cells are target cells. Multipotential mesenchymal stem cells are located within the range of alpha particles, and are the most likely target cells for the fibroblastic type of bone sarcoma. The histogenesis of bone sarcomas after irradiation with alpha emitters shows that their final histopathology is not dependent on a single target cell. Each target cell has a microenvironment, which has to be regarded as a synergistic morpho-functional tissue unit. For this the concept of 'histion', a term used in general pathology, is proposed. Interactions between target cells that have been hit by alpha-particles, leading to lethal, mutational or transformation events with all components of a 'histion', will prove critical to understanding the pathogenesis of both deterministic and stochastic late effects. (author)

  17. Target cells in internal dosimetry

    International Nuclear Information System (INIS)

    Goessner, W.

    2003-01-01

    Data related to radium induced bone sarcomas in humans are used as a model for defining target cells on bone surfaces and in the bone marrow. The differential distribution of radiation induced bone sarcoma types with a high ratio of non-bone producing, mainly fibroblastic tumours, challenges the ICRP concept that the bone lining cells are target cells. Multipotential mesenchymal stem cells are located within the range of alpha particles, and are the most likely target cells for the fibroblastic type of bone sarcoma. The histogenesis of bone sarcomas after irradiation with alpha emitters shows that their final histopathology is not dependent on a single target cell. Each target cell has a microenvironment, which has to be regarded as a synergistic morpho-functional tissue unit. For this the concept of 'histion', a term used in general pathology, is proposed. Interactions between target cells that have been hit by alpha-particles, leading to lethal, mutational or transformation events with all components of a 'histion', will prove critical to understanding the pathogenesis of both deterministic and stochastic late effects. (author)

  18. Target assignment for security officers to K targets (TASK)

    International Nuclear Information System (INIS)

    Rowland, J.R.; Shelton, K.W.; Stunkel, C.B.

    1983-02-01

    A probabilistic algorithm is developed to provide an optimal Target Assignment for Security officers to K targets (TASK) using a maximin criterion. Under the assumption of only a limited number (N) of security officers, the TASK computer model determines deployment assignments which maximize the system protection against sabotage by an adversary who may select any link in the system, including the weakest, for the point of attack. Applying the TASK model to a hypothetical nuclear facility containing a nine-level building reveals that aggregate targets covering multiple vital areas should be utilized to reduce the number of possible target assignments to a value equal to or only slightly larger than N. The increased probability that a given aggregate target is covered by one or more security officers offsets the slight decrease in interruption probability due to its occurring earlier in the adversary's path. In brief, the TASK model determines the optimal maximin deployment strategy for limited numbers of security officers and calculates a quantitative measure of the resulting system protection

  19. Progress in ISOL target-ion source systems

    Energy Technology Data Exchange (ETDEWEB)

    Koester, U. [Institut Laue Langevin, 6 Rue Jules Horowitz, F-38042 Grenoble Cedex 9 (France); ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland)], E-mail: koester@ill.fr; Arndt, O. [HGF VISTARS and Institut fuer Kernchemie, Johannes-Gutenberg Universitaet Mainz, D-55128 Mainz (Germany); Bouquerel, E.; Fedoseyev, V.N. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Franberg, H. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Laboratory for Radio- and Environmental Chemistry, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Joinet, A. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Centre d' Etude Spatiale des Rayonnements, 9 Av. du Colonel Roche, F-31028 Toulouse Cedex 4 (France); Jost, C. [HGF VISTARS and Institut fuer Kernchemie, Johannes-Gutenberg Universitaet Mainz, D-55128 Mainz (Germany); Kerkines, I.S.K. [Laboratory of Physical Chemistry, National and Kapodistrian University of Athens, Department of Chemistry, Zografou 157 71, GR (Greece); Cherry L. Emerson Center for Scientific Computation and Department of Chemistry, Emory University, Atlanta, GA 30322 (United States); Kirchner, R. [Gesellschaft fuer Schwerionenforschung, Planckstr. 1, D-64291 Darmstadt (Germany)

    2008-10-15

    The heart of every ISOL (isotope separation on-line) facility is its target and ion source system. Its efficiency, selectivity and rapidity is decisive for the production of intense and pure ion beams of short-lived isotopes. Recent progress in ISOL target and ion source technology is discussed at the examples of radioactive ion beams of exotic zinc and tin isotopes that were purified by isothermal chromatography and molecular sideband separation respectively. An outlook is given to which other elements these purification methods are applicable.

  20. Progress in ISOL target-ion source systems

    International Nuclear Information System (INIS)

    Koester, U.; Arndt, O.; Bouquerel, E.; Fedoseyev, V.N.; Franberg, H.; Joinet, A.; Jost, C.; Kerkines, I.S.K.; Kirchner, R.

    2008-01-01

    The heart of every ISOL (isotope separation on-line) facility is its target and ion source system. Its efficiency, selectivity and rapidity is decisive for the production of intense and pure ion beams of short-lived isotopes. Recent progress in ISOL target and ion source technology is discussed at the examples of radioactive ion beams of exotic zinc and tin isotopes that were purified by isothermal chromatography and molecular sideband separation respectively. An outlook is given to which other elements these purification methods are applicable.