WorldWideScience

Sample records for dynamic voltage restorer

  1. Analyzing of Dynamic Voltage Restorer in Series Compensation Voltage

    Directory of Open Access Journals (Sweden)

    Naser Parhizgar

    2012-02-01

    Full Text Available The Dynamic Voltage Restorer (DVR is a series-connected compensator to generate a controllable voltage to against the short-term voltage disturbances. The technique of DVR is an effective and cost competitive approach to improve voltage quality at the load side. This study presents a single-phase and threephase DVR system with reduced switch-count topology to protect the sensitive load against abnormal voltage conditions. Most basic function, the DVR configuration consist of a two level Voltage Source Converter (VSC, a dc energy storage device, a coupling transformer Connected in shunt with the ac system This study presents the application of Dynamic Voltage Restorer (DVR on power distribution systems for mitigation of voltage sag at critical loads. DVR is one of the compensating types of custom power devices. The DVR, which is based on forced-commutated Voltage Source Converter (VSC has been proved suitable for the task of compensating voltage sags/swells. Simulation results are presented to illustrate and understand the performances of DVR in supporting load voltages under voltage sags/swells conditions.

  2. SIMULATION OF INTERLINE DYNAMIC VOLTAGE RESTORER

    Directory of Open Access Journals (Sweden)

    J.Singaravelan

    2011-08-01

    Full Text Available This paper presents a new approach for the dynamic control of a current source inverter (CSI using Super Conductive Magnetic energy storage (SMES based Interline DVR. The dynamic voltage restorer (DVR provides a technically advanced and economical solution to voltage-sag problem. As the voltage-restoration process involves the real-power injection into the distribution system, the capability ofa DVR, especially for compensating long-duration voltage sags, it depends on the energy storage capacity of the DVR. The interline DVR proposed in this paper provides a way to replenish Dc-link energy storage dynamically. The IDVR consists of several DVRs connected to different distribution feeders in the power system. The DVRs in the IDVR system shares the common energy storage. When one of the DVRcompensates for voltage sag appearing in that feeder, the other DVRs replenish the energy in the common dc-link dynamically. Thus, one DVR in the IDVR system works in voltage-sag compensation mode whilethe other DVRs in the IDVR system operate in power-flow control mode. The proposed topology is simulated using Matlab/Simulink and total IDVR system is simulated using Matlab/Simulink.

  3. Implementation of Dynamic Voltage Restorer for Mitigation of Voltage Sag

    Directory of Open Access Journals (Sweden)

    K.Vinod Kumar

    2013-07-01

    Full Text Available Power quality is one of major concerns in the present. It has become important, especially with the introduction of sophisticated devices, whose performance is very sensitive to the quality of power supply. The dynamic voltage restorer (DVR is one of the modern devices used in distribution systems to improve the power quality. In this paper, emergency control in distribution systems is discussed by using the proposed multifunctional DVR control strategy.Also, themultiloop controller using the Posicast and P+Resonant controllers is proposed in order to improve the transient response and eliminate the steady state error in DVR response,respectively.The proposed process is applied to some riots in load voltage effected by induction motors starting, and a three-phase short circuit fault. The three-phase short circuits, and the large induction motors are suddenly started then voltage sags areoccurred.The innovation here is that by using the Multifunctional Dynamic Voltage Restorer, improve the power quality in distribution side. Simulation results show the capability of the DVR to control the emergency conditions of the distribution systems by using MATLAB/Simulink software.

  4. Voltage Swells Improvement in Low Voltage Network Using Dynamic Voltage Restorer

    Directory of Open Access Journals (Sweden)

    R. Omar

    2011-01-01

    Full Text Available Problem statement: Voltage disturbances are the most common power quality problem due to the increased use of a large numbers of sophisticated electronic equipment in industrial distribution system. The voltage disturbances such as voltage sags, swells, harmonics, unbalance and flickers. High quality in the power supply is needed, since failures due to such disturbances usually have a high impact on production cost. There are many different solutions to compensate voltage disturbances but the use of a DVR is considered to be the most cost effective method. The objective of this study is to propose a new topology of a DVR in order to mitigate voltage swells using a powerful power custom device namely the Dynamic Voltage Restorer (DVR. Approach: New configuration of a DVR with an improvement of a controller based on direct-quadrature-zero method has been introduced to compensate voltage swells in the network. Results: The effectiveness of the DVR with its controller were verify using Matlab/Simulinks SimPower Toolbox and then implemented using 5KVA DVR experimental setup. Simulations and experimental results demonstrate the effective dynamic performance of the proposed configuration. Conclusion: The implimentation of the proposed DVR validate the capabilities in mitigating of voltage swells effectiveness.During voltage swells, the DVR injects an appropriate voltage to maintain the load voltage at its nominal value.

  5. Improved Phasor Estimation Method for Dynamic Voltage Restorer Applications

    DEFF Research Database (Denmark)

    Ebrahimzadeh, Esmaeil; Farhangi, Shahrokh; Iman-Eini, Hossein;

    2015-01-01

    The dynamic voltage restorer (DVR) is a series compensator for distribution system applications, which protects sensitive loads against voltage sags by fast voltage injection. The DVR must estimate the magnitude and phase of the measured voltages to achieve the desired performance. This paper...... proposes a phasor parameter estimation algorithm based on a recursive variable and fixed data window least error squares (LES) method for the DVR control system. The proposed algorithm, in addition to decreasing the computational burden, improves the frequency response of the control scheme based...... on the fixed data window LES method. The DVR control system based on the proposed algorithm provides a better compromise between the estimation speed and accuracy of the voltage and current signals and can be implemented using a simple and low-cost processor. The results of the studies indicate...

  6. Power conditioning using dynamic voltage restorers under different voltage sag types

    Directory of Open Access Journals (Sweden)

    Ahmed M. Saeed

    2016-01-01

    Full Text Available Voltage sags can be symmetrical or unsymmetrical depending on the causes of the sag. At the present time, one of the most common procedures for mitigating voltage sags is by the use of dynamic voltage restorers (DVRs. By definition, a DVR is a controlled voltage source inserted between the network and a sensitive load through a booster transformer injecting voltage into the network in order to correct any disturbance affecting a sensitive load voltage. In this paper, modelling of DVR for voltage correction using MatLab software is presented. The performance of the device under different voltage sag types is described, where the voltage sag types are introduced using the different types of short-circuit faults included in the environment of the MatLab/Simulink package. The robustness of the proposed device is evaluated using the common voltage sag indices, while taking into account voltage and current unbalance percentages, where maintaining the total harmonic distortion percentage of the load voltage within a specified range is desired. Finally, several simulation results are shown in order to highlight that the DVR is capable of effective correction of the voltage sag while minimizing the grid voltage unbalance and distortion, regardless of the fault type.

  7. Power conditioning using dynamic voltage restorers under different voltage sag types.

    Science.gov (United States)

    Saeed, Ahmed M; Abdel Aleem, Shady H E; Ibrahim, Ahmed M; Balci, Murat E; El-Zahab, Essam E A

    2016-01-01

    Voltage sags can be symmetrical or unsymmetrical depending on the causes of the sag. At the present time, one of the most common procedures for mitigating voltage sags is by the use of dynamic voltage restorers (DVRs). By definition, a DVR is a controlled voltage source inserted between the network and a sensitive load through a booster transformer injecting voltage into the network in order to correct any disturbance affecting a sensitive load voltage. In this paper, modelling of DVR for voltage correction using MatLab software is presented. The performance of the device under different voltage sag types is described, where the voltage sag types are introduced using the different types of short-circuit faults included in the environment of the MatLab/Simulink package. The robustness of the proposed device is evaluated using the common voltage sag indices, while taking into account voltage and current unbalance percentages, where maintaining the total harmonic distortion percentage of the load voltage within a specified range is desired. Finally, several simulation results are shown in order to highlight that the DVR is capable of effective correction of the voltage sag while minimizing the grid voltage unbalance and distortion, regardless of the fault type.

  8. New Control Technique Applied in Dynamic Voltage Restorer for Voltage Sag Mitigation

    Directory of Open Access Journals (Sweden)

    Rosli Omar

    2010-01-01

    Full Text Available The Dynamic Voltage Restorer (DVR was a power electronics device that was able to compensate voltage sags on critical loads dynamically. The DVR consists of VSC, injection transformers, passive filters and energy storage (lead acid battery. By injecting an appropriate voltage, the DVR restores a voltage waveform and ensures constant load voltage. There were so many types of the control techniques being used in DVR for mitigating voltage sags. The efficiency of the DVR depends on the efficiency of the control technique involved in switching the inverter. Problem statement: Simulation and experimental investigation toward new algorithms development based on SVPWM. Understanding the nature of DVR and performance comparisons between the various controller technologies available. The proposed controller using space vector modulation techniques obtain higher amplitude modulation indexes if compared with conventional SPWM techniques. Moreover, space vector modulation techniques can be easily implemented using digital processors. Space vector PWM can produce about 15% higher output voltage than standard Sinusoidal PWM. Approach: The purpose of this research was to study the implementation of SVPWM in DVR. The proposed control algorithm was investigated through computer simulation by using PSCAD/EMTDC software. Results: From simulation and experimental results showed the effectiveness and efficiency of the proposed controller based on SVPWM in mitigating voltage sags in low voltage distribution systems. It was concluded that its controller also works well both in balance and unbalance conditions of voltages. Conclusion/Recommendations: The simulation and experimental results of a DVR using PSCAD/EMTDC software based on SVPWM technique showed clearly the performance of the DVR in mitigating voltage sags. The DVR operates without any difficulties to inject the appropriate voltage component to correct rapidly any anomaly in the supply voltage to keep the

  9. Design and control of single-phase dynamic voltage restorer

    Indian Academy of Sciences (India)

    AMIT MEENA; SHIRAZUL ISLAM; SANDEEP ANAND; YOGESH SONAWANE; SANJAY TUNGARE

    2017-08-01

    Dynamic voltage restorer (DVR) is a custom power device used in electrical distribution system for power quality improvement. It ensures regulated voltage supply to the sensitive loads, even in case of voltage sag and swell disturbances in the distribution network. It is a series connected device and compensates voltagesag and swell by injecting a voltage with the help of a series transformer. The injection of an appropriate voltage component in the event of a voltage disturbance requires a certain amount of real and reactive power. Conventionally,DVR consists of an energy storage device, which supplies the required power over the limited duration of the sags. Large magnitude and long duration of sags lead to heavy financial investment in energy storage unit. To overcome this limitation, a single-phase back-to-back converter-based DVR is implemented inthis work, which eliminates energy storage requirement. The integration of series and shunt converter makes the DVR capable of bidirectional flow of energy. Therefore, the key advantage of this topology is its capability to compensate for long-term voltage sag and swell. Modelling of the DVR and its controller design is included in this paper. The effectiveness of control schemes, protection schemes and starting sequence of operation of DVR is verified through detailed simulation studies. A scaled down laboratory prototype of DVR is developed. The viability of these schemes is confirmed by the experimental results generated from the laboratory prototype. Various challenges faced during the prototype development and corresponding solutions are also discussed in this paper.

  10. Analysis and Mathematical Model for Restitution of Voltage Using Dynamic Voltage Restorer

    Directory of Open Access Journals (Sweden)

    C. Gopinath

    2014-01-01

    Full Text Available Voltage sag and swell have a major concern in the distribution systems. In order to mitigate the voltage sag and swell, a custom power device called dynamic voltage restorer (DVR is used. The proposed system is a polymer electrolyte membrane (PEM fuel cell based DVR. The energy from the fuel cell is stored in the super capacitor to restitute the voltage. In this proposed DVR, Z-source inverter is used instead of traditional inverter because of buck-boost and shoot through capability. The simulation is performed using three controller topologies: PI controller, synchronous reference frame controller and fuzzy controller and the results are verified using Matlab-Simulink environment.

  11. More stability and robustness with the multi-loop control solution for dynamic voltage restorer (DVR)

    OpenAIRE

    2009-01-01

    This paper presents the application of dynamic voltage restorers (DVR) on power distribution systems for mitigation of voltage sags/swells at critical loads. DVR is one of the compensating types of custom power devices. An adequate modeling and simulation of DVR, including controls in MATLAB, based on forced-commutated voltage source converter (VSC), has been proved suitable for compensating the voltage sags/swells. In this paper, a double loop control method is proposed for the improvement o...

  12. Dynamic Voltage Restorer Based on Space Vector Pulse Width Modulation Technique

    Directory of Open Access Journals (Sweden)

    B.N S P Venkatesh

    2011-07-01

    Full Text Available Power Quality problems encompass a wide range of disturbances such as voltage sags, swells, flicker,harmonics distortion and interruptions. The strategic deployment of custom power devices has been proposed asone of the means to protect sensitive loads from power quality problems such as voltage sags and swells. The Dynamic Voltage Restorer (DVR is a power electronic device that is used to inject 3-phase voltage in series and in synchronism with the distribution feeder voltages in order to compensate voltage sag and similarly itreacts quickly to inject the appropriate voltage component (negative voltage magnitude in order to compensate voltage swell. The principal component of the DVR is a voltage source inverter that generates three phase voltages and provides the voltage support to a sensitive load during voltage sags and swells. Pulse Width Modulation Technique is very critical for proper control of DVR. Sinusoidal Pulse Width Modulation (SPWM and Space Vector Pulse Width Modulation (SVPWM control techniques are used for controlling the DVR. Inthis work, the operation of DVR is presented and the control technique used for voltage source inverter is Space Vector PWM technique. Space vector PWM can utilize the better dc voltage and generates the fewer harmonic in inverter output voltage than Sinusoidal PWM technique. This work describes the DVR based on Space Vector PWM which provides voltage support to sensitive loads and is simulated by using MATLAB/SIMULINK. Simulation results show that the control approach is able to compensate for any type of voltage sags and swells.

  13. A Versatile Control Scheme For Dynamic Voltage Restorer To Limit Downstream Fault Currents

    Directory of Open Access Journals (Sweden)

    A.Nagendra

    2014-12-01

    Full Text Available The Dynamic Voltage Restorer (DVR is a custom power device utilized to counteract voltage sags. It injects controlled three-phase ac voltages in series with the supply voltage, subsequent to voltage sag, to enhance voltage quality by adjusting the voltage magnitude, wave shape, and phase angle. The DVR is conventionally bypassed during a downstream fault to prevent potential adverse impacts on the fault and to protect the DVR components against the fault current. This paper proposes an augmented control strategy for the DVR that provides:1 voltage-sag compensation under balanced and unbalanced conditions and 2 a fault current interruption (FCI function. This paper introduces and evaluates an auxiliary control strategy for downstream fault current interruption in a radial distribution line by means of a dynamic voltage restorer (DVR. The proposed controller supplements the voltage-sag compensation control of the DVR. It does not require phaselocked loop and independently controls the magnitude and phase angle of the injected voltage for each phase. Fast least error squares digital filters are used to estimate the magnitude and phase of the measured voltages and effectively reduce the impacts of noise, harmonics, and disturbances on the estimated phasor parameters, and this enables effective fault current interrupting even under arcing fault conditions. The performance of the DVR for fault current interruption is analyzed by using MATLAB/SIMULINK software.

  14. Improving Low Voltage Ride Through Capability of Wind Generators Using Dynamic Voltage Restorer

    Science.gov (United States)

    Sivasankar, Gangatharan; Suresh Kumar, Velu

    2014-08-01

    The increasing wind power integration with power grid has forced the situation to improve the reliability of wind generators for stable operation. One important problem with induction generator based wind farm is its low ride through capability to the grid voltage disturbance. Any disturbance such as voltage dip may cause wind farm outages. Since wind power contribution is in predominant percentage, such outages may lead to stability problem. The proposed strategy is to use dynamic voltage controller (DVR) to compensate the voltage disturbance. The DVR provides the wind generator the ability to remain connected in grid and improve the reliability. The voltage dips due to symmetrical and unsymmetrical faults are considered for analysis. The vector control scheme is employed for fault compensation which uses software phase locked loop scheme and park dq0 transformation technique. Extensive simulation results are included to illustrate the control and operation of DVR.

  15. More stability and robustness with the multi-loop control solution for dynamic voltage restorer (DVR

    Directory of Open Access Journals (Sweden)

    Abdelkhalek Othmane

    2009-01-01

    Full Text Available This paper presents the application of dynamic voltage restorers (DVR on power distribution systems for mitigation of voltage sags/swells at critical loads. DVR is one of the compensating types of custom power devices. An adequate modeling and simulation of DVR, including controls in MATLAB, based on forced-commutated voltage source converter (VSC, has been proved suitable for compensating the voltage sags/swells. In this paper, a double loop control method is proposed for the improvement of the stability of DVR during the load current variation. For the main loop (Outer Voltage Loop, we use a PI controller for the regulation of the filter condenser voltage. The second loop (Inner Current Loop also uses a PI controller to control the disturbances current during load variation. Simulation results are presented to illustrate and understand the performances of DVR in the compensation of voltage sags/swell even with variation load condition.

  16. Design and Control of a Dynamic Voltage Restorer

    DEFF Research Database (Denmark)

    Nielsen, John Godsk

    . The advantages and disadvantages are treated by inserting the DVR in either the medium voltage distribution system or in the low voltage distribution system. Different topologies for a DVR are investigated on a converter and system level and the protection issues are treated. The design of a DVR is treated...... and two prototype DVRs are designed and specified. The first DVR is a low voltage DVR (LV-DVR) rated for 10 kVA for insertion in a 400 V low voltage grid and the second DVR is a high voltage DVR (HV-DVR) rated for 200 kVA for insertion in a 10 kV medium voltage distribution system. The control issues...... in order to aid the design process and perform simulations on a DVR. The simulations have been compared with measurements in order to be able to test the validity of the models. A good agreement have been found between simulations and measurements, which indicates that the system is sufficiently modelled...

  17. Sliding Mode Control of Dynamic Voltage Restorer by Using a New Adaptive Reaching Law

    Science.gov (United States)

    Pandey, Achala; Agrawal, Rekha; Mandloi, Ravindra S.; Sarkar, Biswaroop

    2017-08-01

    This paper presents a new kind of adaptive reaching law for sliding mode control of Dynamic Voltage Restorer (DVR). Such an adaptive reaching law follows under-damped sinusoidal nature that causes the initial state to reach the sliding regime in extremely less time with negligible chattering. Moreover, it is robust in the sense the trajectory does not deviate from the sliding surface. This new approach is developed and successfully applied to DVR. The simulation results are presented that show its robustness.

  18. Power Quality Improvement Using an Enhanced Network-Side-Shunt-Connected Dynamic Voltage Restorer

    Science.gov (United States)

    Fereidouni, Alireza; Masoum, Mohammad A. S.; Moghbel, Moayed

    2015-10-01

    Among the four basic dynamic voltage restorer (DVR) topologies, the network-side shunt-connected DVR (NSSC-DVR) has a relatively poor performance and is investigated in this paper. A new configuration is proposed and implemented for NSSC-DVR to enhance its performance in compensating (un)symmetrical deep and long voltage sags and mitigate voltage harmonics. The enhanced NSSC-DVR model includes a three-phase half-bridge semi-controlled network-side-shunt-connected rectifier and a three-phase full-bridge series-connected inverter implemented with a back-to-back configuration through a bidirectional buck-boost converter. The network-side-shunt-connected rectifier is employed to inject/draw the required energy by NSSC-DVR to restore the load voltage to its pre-fault value under sag/swell conditions. The buck-boost converter is responsible for maintaining the DC-link voltage of the series-connected inverter at its designated value in order to improve the NSSC-DVR capability in compensating deep and long voltage sags/swells. The full-bridge series-connected inverter permits to compensate unbalance voltage sags containing zero-sequence component. The harmonic compensation of the load voltage is achieved by extracting harmonics from the distorted network voltage using an artificial neural network (ANN) method called adaptive linear neuron (Adaline) strategy. Detailed simulations are performed by SIMULINK/MATLAB software for six case studies to verify the highly robustness of the proposed NSSC-DVR model under various conditions.

  19. A dynamic voltage restorer (DVR) with selective harmonic compensation at medium voltage level

    DEFF Research Database (Denmark)

    Newman, M.J.; Holmes, D.G.; Nielsen, J.G.;

    2005-01-01

    -state power through the DVR, the increased losses, and the low modulation depths at which the scheme must operate to achieve acceptable harmonic compensation performance. This paper presents a selective harmonic feedback control strategy that can be easily added to medium-voltage DVR systems to provide...... be advantageous if the series-connected inverter of a DVR could also be used to compensate for any steady-state load voltage harmonics, since this would increase the power quality "value-added" benefits to the grid system. However, before this can be done, consideration must be given to the control of steady...... voltage harmonic compensation capabilities with minimal effect on the sag compensation performance of the basic DVR. The proposed controller has been experimentally verified on a medium-voltage (10 kV) three-phase DVR prototype under a range of conditions, including distorted supply voltages, nonlinear...

  20. Comparative Studies of Different Control Strategies of a Dynamic Voltage Restorer Based on Matrix Converter

    Directory of Open Access Journals (Sweden)

    Amin Shabanpour

    2012-01-01

    Full Text Available A dynamic voltage restorer (DVR with no energy storage is studied. By using a matrix converter instead of the conventional AC/DC/AC converters, elimination of the DC-link capacitor is possible. The switching algorithm of matrix converter is the space vector modulation. There are different compensation algorithms to control the conventional DVR. These methods have been analyzed in this paper for the proposed matrix-converter-based DVR. A deep analysis through different diagrams would show the advantages or disadvantages of each compensation method. Equations for all methods are derived, and the characteristics of algorithms are compared with each other.

  1. Design and Simulation of Dynamic Voltage Restorer based on Fuzzy Controller Optimized by ANFIS

    Directory of Open Access Journals (Sweden)

    Brahim Ferdi

    2014-03-01

    Full Text Available The fuzzy logic controller (FLC appears to be the unique solution when the process is too complex for analysis by conventional techniques or when the available information data are interpreted qualitatively, inexactly or with uncertainty. In literature, the proposed FLC in general consists of two inputs (error and derivative of error and one output. The number of membership functions is chosen in most cases to be five or seven regardless of the approach used for the design. In this paper, we propose Adaptive Neuro-Fuzzy Inference System (ANFIS approach to optimize the two inputs one output FLC with seven membership functions to one input one output FLC with three membership functions without compromising accuracy. The study is applied to control a Dynamic Voltage Restorer (DVR in voltage sag/swell mitigation. The results of simulation using MATLAB/SIMULINK show that the performance of the optimal FLC generated by ANFIS is comparable with the initial given FLC.

  2. Sag mitigation in distribution system by using Dynamic voltage Restorer (DVR

    Directory of Open Access Journals (Sweden)

    Neelam Rani

    2014-12-01

    Full Text Available Power quality is most important concern in the current age. It’s now a day’s necessary with the refined devices, where performance is very perceptive to the quality of power supply. Power quality crisis is an incidence manifest as a typical voltage, current or frequency that results in a failure of end use equipments. One of the major crises dealt here is the power sag. Perceptive industrial loads and distribution networks suffer from different types of service interruptions and outages which results in a major financial loss. To improve the power quality, custom power-devices are used. The device considered in this work is Dynamic Voltage Restorer. This paper shows modelling, analysis and simulation of a DVR test systems using MATLAB. I have considered single line to ground fault for linear load. The role of DVR is to “compensate load voltage” is examined during the different fault conditions like voltage sag, single phase to ground faults.

  3. Comparison between Different Control Strategies of a Z-Source Inverter Based Dynamic Voltage Restorer

    Directory of Open Access Journals (Sweden)

    Abolfazl Kazemdehdashti

    2013-01-01

    Full Text Available In this paper, dynamic voltage restorer (DVR compensation methods are compared to each other for the load side connected shunt converter topology of z-source inverter based DVR to choose the best method. Four different topologies are recognized for DVR that two of them have energy storage devices, and two topologies have no energy storage that take ener\\-gy from the grid during the period of compensation. Here the load side connected shunt converter topology that takes necessary energy from the grid is used. Pre-sag compensation, in-phase compensation, energy-optimized methods are the three DVR compensation methods that studied and compared. A deep analysis through different diagrams would show the advantages or disadvantages of each compensation method. Equations for all methods are derived and the characteristics of algorithms are compared with each other. The simulation results done by SIMULINK/ MATLAB shows compensating by this topology based on the compensation methods.

  4. Improved fault ride through capability of DFIG based wind turbines using synchronous reference frame control based dynamic voltage restorer.

    Science.gov (United States)

    Rini Ann Jerin, A; Kaliannan, Palanisamy; Subramaniam, Umashankar

    2017-09-01

    Fault ride through (FRT) capability in wind turbines to maintain the grid stability during faults has become mandatory with the increasing grid penetration of wind energy. Doubly fed induction generator based wind turbine (DFIG-WT) is the most popularly utilized type of generator but highly susceptible to the voltage disturbances in grid. Dynamic voltage restorer (DVR) based external FRT capability improvement is considered. Since DVR is capable of providing fast voltage sag mitigation during faults and can maintain the nominal operating conditions for DFIG-WT. The effectiveness of the DVR using Synchronous reference frame (SRF) control is investigated for FRT capability in DFIG-WT during both balanced and unbalanced fault conditions. The operation of DVR is confirmed using time-domain simulation in MATLAB/Simulink using 1.5MW DFIG-WT. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  5. Preparation of Power Distribution System for High Penetration of Renewable Energy Part I. Dynamic Voltage Restorer for Voltage Regulation Pat II. Distribution Circuit Modeling and Validation

    Science.gov (United States)

    Khoshkbar Sadigh, Arash

    Part I: Dynamic Voltage Restorer In the present power grids, voltage sags are recognized as a serious threat and a frequently occurring power-quality problem and have costly consequence such as sensitive loads tripping and production loss. Consequently, the demand for high power quality and voltage stability becomes a pressing issue. Dynamic voltage restorer (DVR), as a custom power device, is more effective and direct solutions for "restoring" the quality of voltage at its load-side terminals when the quality of voltage at its source-side terminals is disturbed. In the first part of this thesis, a DVR configuration with no need of bulky dc link capacitor or energy storage is proposed. This fact causes to reduce the size of the DVR and increase the reliability of the circuit. In addition, the proposed DVR topology is based on high-frequency isolation transformer resulting in the size reduction of transformer. The proposed DVR circuit, which is suitable for both low- and medium-voltage applications, is based on dc-ac converters connected in series to split the main dc link between the inputs of dc-ac converters. This feature makes it possible to use modular dc-ac converters and utilize low-voltage components in these converters whenever it is required to use DVR in medium-voltage application. The proposed configuration is tested under different conditions of load power factor and grid voltage harmonic. It has been shown that proposed DVR can compensate the voltage sag effectively and protect the sensitive loads. Following the proposition of the DVR topology, a fundamental voltage amplitude detection method which is applicable in both single/three-phase systems for DVR applications is proposed. The advantages of proposed method include application in distorted power grid with no need of any low-pass filter, precise and reliable detection, simple computation and implementation without using a phased locked loop and lookup table. The proposed method has been verified

  6. 微电网动态电压恢复器运行模式研究%Research on Operation Modes of Dynamic Voltage Restorer in Microgrid

    Institute of Scientific and Technical Information of China (English)

    成瑞芬; 韩肖清; 王鹏; 秦文萍; 张东霞

    2013-01-01

    针对微电网中存在的电压质量问题,提出了基于光蓄发电单元的动态电压恢复器(dynamic voltage restorer,DVR).DVR以光蓄发电单元为储能单元,通过整流器串联接入到低压配电网与微电网公共连接处.提出了DVR的动态电压恢复方式、不间断供电方式和微电源方式的3种运行模式.通过对系统开关信号进行合理控制,实现3种模式的有效切换,提高DVR设备的利用率.DVR的动态电压恢复方式可有效抑制电压暂降或骤升,改善微电网电压质量;不间断供电方式可提高对负荷的供电可靠性;微电源方式可以减少主网的电能供给,实现节能减排.算例结果验证了DVR的有效性.%In allusion to dissatisfied voltage quality of microgrid,a dynamic voltage restorer (DVR) based on photovoltaic (PV) generation/battery units is proposed.Utilizing PV generation/battery units as energy storage component and via rectifier,the proposed DVR is connected in series with the point of common coupling (PCC),where the microgrid low-voltage is connected to distribution network.Three operating modes of DVR,namely the dynamic voltage restoration mode,the uninterruptible power supply mode and the micro-source mode,are put forward.Through reasonably control strategy,the switching-over among the three operation modes can be effectively implemented to improve the utilization rate of DVR.The dynamic voltage restoration mode of DVR can suppress voltage sag and voltage swell effectively,thus the voltage quality is improved; the uninterruptible power supply mode can improve the reliability of power supply; using the micro-source mode,the power supply from power grid can be reduced and it is favorable for energy conservation and emission reduction.The effectiveness of the proposed DVR is verified by results of simulation based on Matlab/Simulink.

  7. A Novel Method on Fault Ride-Through of a DFIG Wind Turbine using a Dynamic Voltage Restorer During Symmetrical and Asymmetrical Grid Faults

    Directory of Open Access Journals (Sweden)

    S. Radha Krishna Reddy

    2012-10-01

    Full Text Available The application of a dynamic voltage restorer (DVR connected to a wind-turbine-driven doubly fed induction generator (DFIG is investigated. The setup allows the wind turbine system an uninterruptible fault ride-through of voltage dips. The DVR can compensate the faulty line voltage, while the DFIG wind turbine can continue its nominal operation as demanded in actual grid codes. Simulation results for a 2 MW wind turbine and measurement results on a 22 kW laboratory setup are presented, especially for asymmetrical grid faults. They show the effectiveness of the DVR in comparison to the low-voltage ride-through of the DFIG using a crowbar that does not allow continuous reactive power production.

  8. 动态电压恢复器的快速检测及补偿策略%Fast Detection and Compensation Strategy Applied for Dynamic Voltage Restorer

    Institute of Scientific and Technical Information of China (English)

    杨浩; 王宇; 石巍; 方太勋; 刘为群

    2015-01-01

    Low voltage ride through(LVRT)is an important technical problem for power quality.In order to study LVRT,this paper designed an LVRT experimental system composed of dynamic voltage restorer(DVR),and used voltage dq integrated value and its change rate as detection criterion for voltage drops,and used the voltage feed forward and resonance control loop as the compensation strategy,which can achieve fast compensation of low voltage power grid fault.The experiment is completed using above platform.The test results show that DVR which adopts above detection and compensation strategy can achieve the compensation for low voltage fault quickly.%为了研究低电压穿越问题,设计了一套由动态电压恢复器组成的低电压穿越试验系统。提出采用电压 dq 综合值结合其变化率作为低电压故障发生检测判据,采用电压差前馈结合谐振控制环作为补偿策略,实现对电网低电压故障的快速补偿。经电压补偿试验表明,采用上述低电压故障检测及补偿策略的动态电压恢复器能够快速实现电压补偿。

  9. 限流式动态电压恢复器及其参数设计%Dynamic voltage restorer with current limiting function and its parameter design

    Institute of Scientific and Technical Information of China (English)

    唐君华; 涂春鸣; 姜飞; 刘子维; 郭成; 帅智康

    2015-01-01

    为优化电网正常运行时的电能质量,针对电力系统短路故障问题,提出了一种限流式动态电压恢复器(Dynamic voltage restorer with fault current limiting, DVR-FCL)拓扑结构。以限流阻抗值为目标函数,考虑直流侧电压整定的参数设计,给出了 DVR-FCL 的直流侧电压、输出滤波器、串联变压器参数、串联变流器、直流侧电容的整定方法。利用PSCAD/EMTDC仿真软件验证了DVR-FCL对电压跌落及短路故障的动作特性。结果表明,所提拓扑结构和参数设计方法正确,可实现改善电压质量和短路限流的双重功能,保证了电力系统安全性和稳定性。%For the voltage quality optimization under normal power operation, aiming at short-circuit fault in power system, a topology of dynamic voltage restorer with current limiting function (DVR-FCL) is proposed. A parameter design of DVR-FCL based on the objective function of current limiting impedance and the adjustment of DC voltage is introduced. The design methods of the DC link voltage, the output filter, series transformer capacity, the leakage reactance, the series converter and the DC link capacitor are analyzed in detail. The operations of DVR-FCL to voltage sag and short-circuit fault are respectively verified by PSCAD/EMTDC. Simulation results show that the proposed topology and parameters design methods are correct and reasonable, and can effectively realize the double functions of voltage quality improvement and fault current limiting. Thus, it can ensure the security and stability of power system.

  10. Improved dq Transform Algorithm for Dynamic Voltage Restorer Detection%改进dq变换的动态电压恢复器检测新方法

    Institute of Scientific and Technical Information of China (English)

    黄永红; 施慧; 徐俊俊; 张云帅

    2016-01-01

    To meet the real-time and accuracy requirements for voltage sag detection in dynamic voltage restorer,an im⁃proved dq transform algorithm based on adaptive least mean square(LMS)filter and software phase-locked loop is pro⁃posed.The adaptive LMS algorithm with time delayed feedback is applied to the digital filter,which is applied to the control process of software phase-locked loop. The filtering process is conducted in advance,where instead of the tradi⁃tional low pass filter,derivative method is used to isolate the DC component under dq coordinate system instantaneous⁃ly. The proposed method can improve the accuracy of voltage sampling value,accomplish phase lock,and improve the accuracy and response speed of voltage sag detection.A simulation model built in PSCAD/EMTDC validates the ef⁃fectiveness of the proposed method .%为了满足动态电压恢复器的电压暂降检测实时性和准确性要求,提出了基于自适应最小均方LMS(least mean square)滤波器及其软件锁相环的改进dq变换新方法。结合自适应LMS算法与延时正反馈构成数字滤波器,将其应用于dq变换的软件锁相环控制过程中。并使滤波环节提前,采用求导法代替传统低通滤波器瞬时分离出dq坐标系下的直流分量。该方法可提高电压采样值的准确度,实现有效锁相,提高电压暂降检测精度及响应速度。通过PSCAD/EMTDC进行仿真验证,结果表明了该方法的有效性。

  11. Voltage Controlled Dynamic Demand Response

    DEFF Research Database (Denmark)

    Bhattarai, Bishnu Prasad; Bak-Jensen, Birgitte; Mahat, Pukar

    2013-01-01

    . An adaptive dynamic model has been developed to determine composite voltage dependency of an aggregated load on feeder level. Following the demand dispatch or control signal, optimum voltage setting at the LV substation is determined based on the voltage dependency of the load. Furthermore, a new technique...

  12. Model predictive control of dynamic voltage restorer%动态电压恢复器的模型预测控制

    Institute of Scientific and Technical Information of China (English)

    裴喜平; 郝晓弘; 陈伟; 肖骏; 王维洲

    2013-01-01

    In order to improve the dynamic response speed and steady accuracy of the dynamic voltage restorer, this paper proposes control strategies based on model predictive control (MPC) and analyzes design methods of controller parameters in detail. On the basis of analysis of the main circuit model for dynamic voltage restorer, the model is improved by the inner current controller and the one-step prediction model of controlled object needed by MPC is acquired, and then a model predictive controller is designed. The proposed control algorithm overcomes the difficulty that traditional model predictive control algorithm based on non-parametric prediction mode is difficult to be directly applied to power systems such as rapid real-time system due to complexity of the algorithm, difficulties of parameter adjustment and amount of computation. It has the merits of feedback correction and dynamic optimization of MPC. Under satisfactory steady accuracy conditions, the proposed strategy improves dynamic response speed significantly. The feasibility of the proposed controller is verified through experimental analysis compared with classic control strategy. This work is supported by National Natural Science Foundation of China (No. 51267012).%  为了提高动态电压恢复器的响应速度和稳态精度,提出了基于模型预测控制的控制策略,详细分析了控制器参数设计方法。在分析动态电压恢复器主电路模型的基础上,采用内环电流控制器对模型进行改进,得出模型预测控制所需的被控对象一步预测模型,设计了模型预测控制器。所提控制算法克服了基于非参数预测模型的模型预测控制由于算法复杂、参数调整困难,计算量大,很难直接应用到电力系统这样的快速实时系统中的问题,同时实现了预测控制滚动优化、反馈校正的优点。在满意的稳定精度下,明显提高了系统的动态响应速度。

  13. SoC-Based Dynamic Power Sharing Method with AC-Bus Voltage Restoration for Microgrid Applications

    DEFF Research Database (Denmark)

    Lu, Xiaonan; Sun, Kai; Guerrero, Josep M.

    2012-01-01

    In a microgrid system, distributed energy storage units are commonly employed as the energy buffers. In this paper, a dynamic power sharing method based on the state-of-charge (SoC) of each energy storage unit is proposed. Droop control is employed as the basic control strategy for the distributed...... shared in the energy storage system. The relationship between the droop coefficient and SoC are studied deeply and the small signal model is developed to verify the stability of the control system. It is found that the active power sharing speed becomes faster with higher exponent of SoC. At the same...... energy storage units. By using the proposed method, the coefficients in the conventional droop method are adjusted according to the SoC of each energy storage module. The modules with higher SoC delivers more active power, while those with lower SoC delivers less. Meanwhile, the reactive power is equally...

  14. Control de un restaurador dinámico de tensión basado en la transformada de Fourier del Vector Espacial. Dynamic voltage restorer control based on the Space-Vector Fourier Transform

    Directory of Open Access Journals (Sweden)

    Lesyani Teresa León Viltre

    2015-04-01

    Full Text Available El gran desarrollo de la automatización industrial, como resultado de la modernización y el progreso de los equipos con microprocesador y electrónica de potencia, ha hecho que las cargas en la actualidad sean más sensibles a las caídas de tensión de corta duración. Estos trastornos, incluso en tiempos muy cortos, pueden detener procesos enteros causando enormes pérdidas. Por esta razón en el presente trabajo se propone un Restaurador Dinámico de Tensión (dynamic voltaje restorer- DVR, para mantener la operación ininterrumpida de una carga industrial, sensible a huecos de tensión. El control propuesto para el DVR está basado en la transformada de Fourier del vector espacial (space vector Fourier transform- SVFT. El vector controlado es implementado en los ejes de referencia estacionarios alfa y beta. Se obtienen resultados satisfactorios ante señales distorsionadas. Se realizan simulaciones en el Matlab del sistema propuesto para huecos de tensión balanceados y desbalanceados.  The great development of industrial automation, as a result of modernization and progress of equipment with microprocessor and power electronics has made loads now more sensitive to voltage drops. These disorders, even in very short time, can stop the whole process causing huge losses. For this reason a dynamic voltage restorer (DVR is proposed in this paper for keeping uninterrupted operation of sensitive industrial load during voltages sags. The proposed DVR controller is based on the Space Vector Fourier Transform (SVFT. The vector controller is implemented in the stationary reference frames. Satisfactory results are obtained for distorted signals.The proposed system is simulated in Matlab for voltage dips balanced and unbalanced.

  15. 补偿约束下动态电压恢复器不对称电压暂降补偿方法%A Method to Compensate Asymmetrical Voltage Sag of Dynamic Voltage Restorer Under Constraint of Compensation Voltage Injection

    Institute of Scientific and Technical Information of China (English)

    魏小淤; 杨洪耕

    2011-01-01

    针对补偿电压注入约束下的不对称电压暂降补偿,提出一种新的动态电压恢复器补偿策略.首先以A相为参考相,以各相电压端点为圆心作补偿极限圆,通过旋转B、C相极限圆得到有效补偿域;然后根据有效补偿域与参考电压圆的交角来确定完全补偿弧;最后沿此弧旋转负荷电压,在弧内求取最小能量注入解.该方法简单直观,适用于补偿三相负荷完全对称时由各种故障类型引起的电压暂降.由于此方法无需先抵偿负序和零序分量,通过在有效补偿域内对源电压进行直接计算,最大故障范围内实现负荷电压的对称补偿,且求解过程无循环搜索,响应速度快,满足实际工程应用的需求.%To compensate asymmetrical voltage sag under the constraint of compensation voltage injection, a new dynamic compensation strategy for dynamic voltage restorer (DVR) is proposed. Firstly, taking phase A as the reference phase, compensation horocircles, whose centers are terminal points of three-phase voltage vectors, are plotted and by means of rotating the horocircles of phase B and C the active compensating area is obtained; then, according to the angle by which the active compensating area intersects to the circle of reference voltage, the complete compensation arc is determined;finally, rotating the load voltage along the arc, the least energy injection of DVR for each phase can be solved. The proposed method is simple and intuitional, so it is suitable to compensate the voltage sag caused by various faults under symmetrical three-phase load. In view of the fact that in the proposed method it is not necessary to pre-compensate the negative- and zero-sequence components, so by means of directly calculating the source voltage within active compensating area the symmetrical compensation of load voltage inside the maximum fault coverage can be implemented. The proposed method can fast respond to voltage sag and the cyclic search

  16. Power Restoration in Medium Voltage Network Using Multiagent System

    Directory of Open Access Journals (Sweden)

    Miroslav Kovac

    2013-01-01

    Full Text Available The article describes a novel approach to a power restoration in medium voltage power distribution network. It focuses primary at searching of a new network configuration enabling to minimalize the size of faulted area and to restore the power for the highest possible number of loads. It describes characteristic features of medium voltage power distribution network and discusses the implementation of the presented approach in existing networks. A software tool, developed by the authors, including physical simulation of model network and its autonomous control system is described. An example of fault situation in a virtual distribution network is presented. Afterwards, the solution of restoration problem by proposed multiagent system is simulated using the software tool described in the paper.

  17. Low Voltage Ride Through Strategy for Wind Turbine Systems Using Dynamic Voltage Restorers%基于动态电压调节器的风电机组低电压穿越策略

    Institute of Scientific and Technical Information of China (English)

    洪芦诚; 魏应冬; 姜齐荣; 王志永

    2011-01-01

    With the penetration level of large-scale grid-connected wind farms increasing year by year,low voltage ride through(LVRT) capability is required by many countries for power quality and fail-safe operation of grid faults.A new dynamic strategy using dynamic voltage restorer(DVR) is proposed to improve LVRT capability of wind turbine generators(WTGs).During the voltage dip,DVR will be connected in series between grid and the generator by opening the static switch cabinet.And the power balance between grid and generator is achieved by using the dynamic braking resistor of DVR.In order to increase the response speed of DVR,anti-voltage technology is used to make the thyristor control rectifier in static switch cabinet shutting off immediately.PSCAD/EMTDC simulations and experiments are carried out to prove the effectiveness of the proposed technique.%随着并网大型风电场装机容量的逐年增长,低电压穿越(LVRT)能力已经逐渐成为风电机组并网的一个重要指标。文中提出了一种利用动态电压调节器(DVR)辅助风电机组在电网电压跌落工况下实现LVRT的策略。DVR串联接入风电机组机端和电网公共连接点(PCC)之间,电网电压正常时通过静态开关柜将其旁路,电网电压跌落时利用反压技术进行快速投切,DVR通过调节使风电机组机端电压维持正常;同时,DVR在风电机组和电网之间提供功率通道,利用直流母线上的刹车电阻消耗掉过剩功率,保证直流电容电压的稳定及风电机组的正常运行。利用

  18. Comprehensive Compensation Control Method of Dynamic Voltage Restorer%动态电压校正装置的综合补偿特性及仿真

    Institute of Scientific and Technical Information of China (English)

    张雪薇; 朱洁; 杜旭红; 孙红雨

    2015-01-01

    Aiming at the shortcomings of the traditional compensation method for voltage sags ,this paper puts forward a comprehensive compensation control method .The paper analyzes the compensation characteristics of the compensation strategy and discusses the device’s strategies with or without voltage constraints .Through the theoretical derivation , letting the output active power be zero , the compensation voltage and the optimum angle in the above two circumstances are calculated .The device’ s simulation model is built to verify the validity of the improved compensation control strategy in three different conditions .A comparative analysis is made with in-phase voltage compensation method for the active power output .The simulation results show that the device’s voltage can be fast and perfectly compensated to the level before the fall although the voltage drops in depth and is accompanied by harmonic ,showing the effectiveness and feasibility of the compensation control method .%针对传统电压跌落补偿方法的不足,提出一种综合补偿控制方法。系统分析了补偿策略的补偿特性;讨论了装置在有电压和无电压约束下的应对策略。通过理论推导,令输出有功为零,计算装置在以上两种情况的补偿电压以及最优角。通过Simulink搭建装置的仿真模型,在三种不同情况下对改进的补偿控制策略的有效性进行验证;同时与同相电压补偿法的有功输出进行对比分析。仿真结果表明装置在电压深度跌落并伴有谐波时依然快速完美的补偿到跌落前水平,证明了该补偿控制方法的有效性和可行性。

  19. Single-phase dynamic voltage restorer based on a new chopper AC/DC/AC conversion%一种新型斩波 AC/DC/AC 变换的单相 DVR

    Institute of Scientific and Technical Information of China (English)

    巫付专; 侯婷婷; 韩梁; 冯占伟

    2015-01-01

    针对输入侧采用不可控整流AC/DC/AC结构的单相动态电压恢复器( DVR )输入侧功率因数低,谐波含量高等问题,提出了一种基于PWM斩波变换器的动态电压恢复器来补偿负载两端电压的跌落。该新型拓扑结构采用PWM斩波控制节省了直流侧电容,简化了滤波器设计,使输入侧线路中谐波含量降低,同时达到单位功率因数;电压检测采用单相信号构造成两相信号,利用瞬时无功理论对信号进行检测与处理,实时性高;搭建MATLAB/Simulink仿真和系统实验平台,验证其合理性和可行性。%In view of such problems as the low input side power factor of the single-phase dynamic voltage restorer ( DVR) with the structure of uncontrolled rectifier AC/DC/AC and high harmonic content , this paper proposed a DVR based on the PWM chopper to compensate for the voltage drop at the two load ends .The new topology , which a-dopted the PWM chopper control , saved the DC capacitor and simplified the filter design so that the harmonic content in the input-side circuit was reduced and the input side achieved the unit power factor .Single-phase signals were con-structed into two-phase signals to detect voltage and the instantaneous reactive power theory was used to detect and process the signals , which attained high real time .Finally, a MATLAB/Simulink simulation and experimental plat-form was constructed to verify the rationality and feasibility of the new structure .

  20. Secondary control for reactive power sharing and voltage amplitude restoration in droop-controlled islanded microgrids

    DEFF Research Database (Denmark)

    Micallef, A.; Apap, M.; Spiteri Staines, C.

    2012-01-01

    This paper focuses on the islanded operation of microgrids. In this mode of operation, the microsources are required to cooperate autonomously to regulate the local grid voltage and frequency. Droop control is typically used to achieve this autonomous voltage and frequency regulation. However...... and to restore the voltage deviations caused by the droop control. Primary droop control loops where implemented in the inverters to supply the real and reactive power. Simulation results are presented showing the feasibility of the proposed algorithm in achieving reactive power sharing between the inverters...... connected to the microgrid while simultaneously restoring the voltage deviations due to the droop control....

  1. Dynamic voltage regulation and power export in a distribution system using distributed generation

    Institute of Scientific and Technical Information of China (English)

    Aamir HANIF; Muhammad Ahmed CHOUDHRY

    2009-01-01

    The major aim of power quality (PQ) enhancing techniques is to maintain a specified voltage magnitude at a desired frequency for sensitive loads irrespective of faults on the power distribution network. The dynamic voltage restorer (DVR) is a device used to mitigate voltage sags to regulate load voltage. This paper presents a mathematical model for leading series voltage injection to mitigate sags thereby achieving the improvement of the utility power factor as well as power sharing between the DVR and utility. The power sharing will be as per requirement to compensate the sags considering the available distributed generation (DG). The approach of mitigating voltage sags using the concept of leading series voltage injection is suitable for those locations where phase shift in the voltage will not cause any problem. The MATLAB/SIMULINK SimPowerSystem toolbox has been used to obtain simulation results to verify the proposed mathematical model.

  2. Wetland restoration, flood pulsing, and disturbance dynamics

    Science.gov (United States)

    Middleton, Beth A.

    1999-01-01

    While it is generally accepted that flood pulsing and disturbance dynamics are critical to wetland viability, there is as yet no consensus among those responsible for wetland restoration about how best to plan for those phenomena or even whether it is really necessary to do so at all. In this groundbreaking book, Dr. Beth Middleton draws upon the latest research from around the world to build a strong case for making flood pulsing and disturbance dynamics integral to the wetland restoration planning process.While the initial chapters of the book are devoted to laying the conceptual foundations, most of the coverage is concerned with demonstrating the practical implications for wetland restoration and management of the latest ecological theory and research. It includes a fascinating case history section in which Dr. Middleton explores the restoration models used in five major North American, European, Australian, African, and Asian wetland projects, and analyzes their relative success from the perspective of flood pulsing and disturbance dynamics planning.Wetland Restoration also features a wealth of practical information useful to all those involved in wetland restoration and management, including: * A compendium of water level tolerances, seed germination, seedling recruitment, adult survival rates, and other key traits of wetland plant species * A bibliography of 1,200 articles and monographs covering all aspects of wetland restoration * A comprehensive directory of wetland restoration ftp sites worldwide * An extensive glossary of essential terms

  3. Dynamic Analysis of Power System Voltage Stability.

    Science.gov (United States)

    Gebreselassie, Assefa

    This thesis investigates the effects of loads and voltage regulators on the dynamic voltage stability of power systems. The analysis focuses on the interactions of machine flux dynamics with loads and voltage control devices. The results are based on eigenvalue analysis of the linearized models and time simulation of the nonlinear models, using models from the Power System Toolbox, a Matlab -based package for the simulation and small signal analysis of nonlinear power systems. The voltage stability analysis results are developed using a single machine single load system with typical machine and network parameters and the NPCC 10-machine system. Dynamic models for generators, exciters and loads are used. The generator is modeled with a pair of poles and one damper circuit in both the d-axis and the q-axis. Saturation effects are included in the model. The IEEE Type DC1 DC commutator exciter model is used for all the exciters. Five different types of loads: constant impedance, constant current, constant power, a first order induction motor model (slip model) and a third order induction motor model (slip-flux model) are considered. The modes of instability and the stability limits of the different representation of loads are examined for two different operating modes of the exciters. The first, when all the exciters are on automatic control and the second when some exciters are on manual control. Modal participation factors are used to determine the characteristics of the critical modes. The characteristics of the unstable modes are verified by performing time simulation of the nonlinear models. Oscillatory and non-oscillatory instabilities are experienced by load buses when all the exciters are on automatic control and some exciters are on manual control respectively, for loads which are predominantly constant power and induction motors. It is concluded that the mode of instability does not depend on the type of loads but on the operating condition of the exciters

  4. A self restoring system on low voltage level

    OpenAIRE

    Bergquist, Hampus

    2012-01-01

    Fortums electric grid in Norra Djurgårdsstaden is a test grid for smart equipment and they are investigating new techniques and ways to improve the quality of the grid. With the quality improvements that are researched, a "self-restoring system" is a part of the research with the intention to lower the amount of outages and shorten the time it takes to restore faults. This thesis can be seen as a part of the optimization process of the grid in Norra Djurgårdsstaden where the benefits with a b...

  5. 10kV动态电压恢复器及其整流控制策略%10 kV Dynamic Voltage Restorer and Its Rectifier Control Strategy

    Institute of Scientific and Technical Information of China (English)

    叶傅华; 陈国栋; 宋晋峰; 周悦

    2011-01-01

    A dynamic voltage restorer(DVR) used in 10 kV distribution network is constructed with no series injection transformer,cascaded cells and a single-phase PWM rectifier connected to the power side.In addition to the principle and characteristics of double closedloop control for single-phase voltage PWM rectifier,a DC voltage single closed-loop control strategy is proposed.It can help to reduce DC voltage level,voltage stress of switch devices and the series amount of DC capacitance.Therefore,the control performance is proved based on the decreased volume and lowered cost.The proposed control strategy and with the DVR compensative control methods are simulated through PSCAD/EMTDC software.Simulation results verify the effectiveness and feasibility of this strategy.%针对10 kV配电系统,动态电压恢复器(DVR)采用无串联变压器、模块级联、从网侧通过可控整流取能的拓扑结构。文章在简单分析了单相电压型PWM整流器双闭环控制原理及特点的基础上,提出了一种直流电压单闭环控制策略。该策略有利于降低直流电压、减小开关器件电压应力、减少直流电容串联的数量,在体积、成本大为减小和降低的同时,其控制性能有所提高。利用PSCAD/EMTDC软件对所提出的控制策略结合DVR的补偿控制进行了仿真,仿真结果验证了该控制策略的有效性及可行性。

  6. Voltage Recovery of Dynamic Slip Control Wind Turbines with a STATCOM

    DEFF Research Database (Denmark)

    Chen, Zhe; Blaabjerg, Frede; Hu, Y.

    2005-01-01

    operating condition quickly for power system stability. This paper studies the voltage recovery of a dynamic slip and turbine pitch controlled wind turbine. A simulation model of a dynamic slip controlled wind turbine in PSCAD/EMTDC is presented, and the control schemes are described. The function......The fast development of wind power generation presents new requirements for the wind turbines integrated into the network. After the clearance of an external short-circuit fault, the voltage at the generator terminal needs to be re-established and the wind turbine should restore its normal...... of a STATCOM in re-establishing the system voltage after the clearance of an external short-circuit fault and restoring the normal operation of the wind turbine has been investigated....

  7. CONTRIBUTIONS OF INTRACELLULAR IONS TO Kv CHANNEL VOLTAGE SENSOR DYNAMICS.

    Directory of Open Access Journals (Sweden)

    Samuel eGoodchild

    2012-06-01

    Full Text Available Voltage sensing domains of Kv channels control ionic conductance through coupling of the movement of charged residues in the S4 segment to conformational changes at the cytoplasmic region of the pore domain, that allow K+ ions to flow. Conformational transitions within the voltage sensing domain caused by changes in the applied voltage across the membrane field are coupled to the conducting pore region and the gating of ionic conductance. However, several other factors not directly linked to the voltage dependent movement of charged residues within the voltage sensor impact the dynamics of the voltage sensor, such as inactivation, ionic conductance, intracellular ion identity and block of the channel by intracellular ligands. The effect of intracellular ions on voltage sensor dynamics is of importance in the interpretation of gating current measurements and the physiology of pore/voltage sensor coupling. There is a significant amount of variability in the reported kinetics of voltage sensor deactivation kinetics of Kv channels attributed to different mechanisms such as open state stabilization, immobilization and relaxation processes of the voltage sensor. Here we separate these factors and focus on the causal role that intracellular ions can play in allosterically modulating the dynamics of Kv voltage sensor deactivation kinetics. These considerations are of critical importance in understanding the molecular determinants of the complete channel gating cycle from activation to deactivation.

  8. Dynamic Performance of Grid Converters using Adaptive DC Voltage Control

    DEFF Research Database (Denmark)

    Trintis, Ionut; Sun, Bo; Guerrero, Josep M.;

    2014-01-01

    This paper investigates a controller that ensures minimum operating dc-link voltage of a back-to-back converter system. The dc-link voltage adapts its reference based on the system state, reference given by an outer loop to the dc-link voltage controller. The operating dc-link voltage should...... be kept as low as possible to increase the power conversion efficiency and increase the reliability of converters. The dynamic performance of the proposed controller is investigated by simulations and experiments....

  9. Scanning transmission electron microscopy imaging dynamics at low accelerating voltages

    Energy Technology Data Exchange (ETDEWEB)

    Lugg, N.R. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Findlay, S.D. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Shibata, N. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); PRESTO, Japan Science and Technology Agency, Saitama 332-0012 (Japan); Mizoguchi, T. [Institute of Industrial Science, The University of Tokyo, Tokyo 153-8505 (Japan); D' Alfonso, A.J. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Allen, L.J., E-mail: lja@unimelb.edu.au [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Ikuhara, Y. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Nanostructures Research Laboratory, Japan Fine Ceramic Center, Nagoya 456-8587 (Japan); WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

    2011-07-15

    Motivated by the desire to minimize specimen damage in beam sensitive specimens, there has been a recent push toward using relatively low accelerating voltages (<100kV) in scanning transmission electron microscopy. To complement experimental efforts on this front, this paper seeks to explore the variations with accelerating voltage of the imaging dynamics, both of the channelling of the fast electron and of the inelastic interactions. High-angle annular-dark field, electron energy loss spectroscopic imaging and annular bright field imaging are all considered. -- Highlights: {yields} Both elastic and inelastic scattering in STEM are acceleration voltage dependent. {yields} HAADF, EELS and ABF imaging are assessed with a view to optimum imaging. {yields} Lower accelerating voltages improve STEM EELS contrast in very thin crystals. {yields} Higher accelerating voltages give better STEM EELS contrast in thicker crystals. {yields} At fixed resolution, higher accelerating voltage aids ABF imaging of light elements.

  10. Influence of Dynamic Properties of Nonlinear Over-Voltage Limiter on Over-Voltage Limitation in Distribution Networks

    Directory of Open Access Journals (Sweden)

    A. N. Bokhan

    2009-01-01

    Full Text Available One of the most efficient means of over-voltage reduction in arcing ground short-circuits is an application of   a nonlinear over-voltage limiter. It is necessary to take into account dynamic properties of the nonlinear over-voltage limiter in order to ensure authentic simulation of  over-voltage in the network A dynamic model of  the non-linear over-voltage limiter which takes a time lag constant   τ  into account during transition of the nonlinear over-voltage limiter into conducting state has been developed in the paper.

  11. Local Dynamic Reactive Power for Correction of System Voltage Problems

    Energy Technology Data Exchange (ETDEWEB)

    Kueck, John D [ORNL; Rizy, D Tom [ORNL; Li, Fangxing [ORNL; Xu, Yan [ORNL; Li, Huijuan [University of Tennessee, Knoxville (UTK); Adhikari, Sarina [ORNL; Irminger, Philip [ORNL

    2008-12-01

    Distribution systems are experiencing outages due to a phenomenon known as local voltage collapse. Local voltage collapse is occurring in part because modern air conditioner compressor motors are much more susceptible to stalling during a voltage dip than older motors. These motors can stall in less than 3 cycles (.05s) when a fault, such as on the sub-transmission system, causes voltage to sag to 70 to 60%. The reasons for this susceptibility are discussed in the report. During the local voltage collapse, voltages are depressed for a period of perhaps one or two minutes. There is a concern that these local events are interacting together over larger areas and may present a challenge to system reliability. An effective method of preventing local voltage collapse is the use of voltage regulation from Distributed Energy Resources (DER) that can supply or absorb reactive power. DER, when properly controlled, can provide a rapid correction to voltage dips and prevent motor stall. This report discusses the phenomenon and causes of local voltage collapse as well as the control methodology we have developed to counter voltage sag. The problem is growing because of the use of low inertia, high efficiency air conditioner (A/C) compressor motors and because the use of electric A/C is growing in use and becoming a larger percentage of system load. A method for local dynamic voltage regulation is discussed which uses reactive power injection or absorption from local DER. This method is independent, rapid, and will not interfere with conventional utility system voltage control. The results of simulations of this method are provided. The method has also been tested at the ORNL s Distributed Energy Communications and Control (DECC) Laboratory using our research inverter and synchronous condenser. These systems at the DECC Lab are interconnected to an actual distribution system, the ORNL distribution system, which is fed from TVA s 161kV sub-transmission backbone. The test results

  12. Moderately nonlinear diffuse-charge dynamics under an ac voltage

    Science.gov (United States)

    Stout, Robert F.; Khair, Aditya S.

    2015-09-01

    The response of a symmetric binary electrolyte between two parallel, blocking electrodes to a moderate amplitude ac voltage is quantified. The diffuse charge dynamics are modeled via the Poisson-Nernst-Planck equations for a dilute solution of point-like ions. The solution to these equations is expressed as a Fourier series with a voltage perturbation expansion for arbitrary Debye layer thickness and ac frequency. Here, the perturbation expansion in voltage proceeds in powers of Vo/(kBT /e ) , where Vo is the amplitude of the driving voltage and kBT /e is the thermal voltage with kB as Boltzmann's constant, T as the temperature, and e as the fundamental charge. We show that the response of the electrolyte remains essentially linear in voltage amplitude at frequencies greater than the RC frequency of Debye layer charging, D /λDL , where D is the ion diffusivity, λD is the Debye layer thickness, and L is half the cell width. In contrast, nonlinear response is predicted at frequencies below the RC frequency. We find that the ion densities exhibit symmetric deviations from the (uniform) equilibrium density at even orders of the voltage amplitude. This leads to the voltage dependence of the current in the external circuit arising from the odd orders of voltage. For instance, the first nonlinear contribution to the current is O (Vo3) which contains the expected third harmonic but also a component oscillating at the applied frequency. We use this to compute a generalized impedance for moderate voltages, the first nonlinear contribution to which is quadratic in Vo. This contribution predicts a decrease in the imaginary part of the impedance at low frequency, which is due to the increase in Debye layer capacitance with increasing Vo. In contrast, the real part of the impedance increases at low frequency, due to adsorption of neutral salt from the bulk to the Debye layer.

  13. Reduced semiconductor three-level interline dynamic voltage restorer

    DEFF Research Database (Denmark)

    Zhang, Lei; Loh, Poh Chang; Gao, Feng;

    2011-01-01

    IDVR system are mainly attributed to its complexity in topology and underutilizations of semiconductors. Aimed to improve the system in these aspects, the paper proposes a new IDVR topology with 25% reduction in semiconductors totally used. The theoretical analysis and its operating principles are also...

  14. Chaotic dynamics of a Chua's system with voltage controllability

    Science.gov (United States)

    Heo, Yun Seok; Jung, Jin Woo; Kim, Ji Man; Jo, Mun Kyu; Song, Han Jung

    2012-04-01

    This paper presents an integrated circuit oriented Chua's chaotic system with voltage controllability. The proposed chaotic system consists of an OTA (Operational Transconductance Amplifier)-based ground inductor, two passive capacitors, a MOS (Metal-Oxide-Semiconductor)-based active resistor and an OTA-based Chua's diode with negative nonlinearity. A SPICE (Simulation Program with Integrated Circuit Emphasis) circuit analysis using 0.5-µm CMOS (Complementary Metal-Oxide-Semiconductor) process parameters was performed for the chaotic dynamics, such as the time waveform and the attractor plot. We confirmed that the chaotic behaviors of the system could be controlled by using the gate voltage of the MOS-based active resistor. Also, various chaotic dynamics of the circuit were analyzed for various MOS sizes of the OTA in the Chua's diode.

  15. Thalamic microinfusion of antibody to a voltage-gated potassium channel restores consciousness during anesthesia.

    Science.gov (United States)

    Alkire, Michael T; Asher, Christopher D; Franciscus, Amanda M; Hahn, Emily L

    2009-04-01

    The Drosophila Shaker mutant fruit-fly, with its malfunctioning voltage-gated potassium channel, exhibits anesthetic requirements that are more than twice normal. Shaker mutants with an abnormal Kv1.2 channel also demonstrate significantly reduced sleep. Given the important role the thalamus plays in both sleep and arousal, the authors investigated whether localized central medial thalamic (CMT) microinfusion of an antibody designed to block the pore of the Kv1.2 channel might awaken anesthetized rats. Male Sprague-Dawley rats were implanted with a cannula aimed at the CMT or lateral thalamus. One week later, unconsciousness was induced with either desflurane (3.6 +/- 0.2%; n = 55) or sevoflurane (1.2 +/- 0.1%; n = 51). Arousal effects of a single 0.5-microl infusion of Kv1.2 potassium channel blocking antibody (0.1- 0.2 mg/ml) or a control infusion of Arc-protein antibody (0.2 mg/ml) were then determined. The Kv1.2 antibody, but not the control antibody, temporarily restored consciousness in 17% of all animals and in 75% of those animals where infusions occurred within the CMT (P Consciousness returned on average (+/- SD) 170 +/- 99 s after infusion and lasted a median time of 398 s (interquartile range: 279-510 s). Temporary seizures, without apparent consciousness, predominated in 33% of all animals. These findings support the idea that the CMT plays a role in modulating levels of arousal during anesthesia and further suggest that voltage-gated potassium channels in the CMT may contribute to regulating arousal or may even be relevant targets of anesthetic action.

  16. Fast Responding Voltage Regulator and Dynamic VAR Compensator

    Energy Technology Data Exchange (ETDEWEB)

    Divan, Deepak [Varentec, Incorporated, San Jose, CA (United States); Moghe, Rohit [Varentec, Incorporated, San Jose, CA (United States); Tholomier, Damien [Varentec, Incorporated, San Jose, CA (United States)

    2014-12-31

    The objectives of this project were to develop a dynamic VAR compensator (DVC) for voltage regulation through VAR support to demonstrate the ability to achieve greater levels of voltage control on electricity distribution networks, and faster response compared to existing grid technology. The goal of the project was to develop a prototype Fast Dynamic VAR Compensator (Fast DVC) hardware device, and this was achieved. In addition to developing the dynamic VAR compensator device, Varentec in partnership with researchers at North Carolina State University (NCSU) successfully met the objectives to model the potential positive impact of such DVCs on representative power networks. This modeling activity validated the ability of distributed dynamic VAR compensators to provide fast voltage regulation and reactive power control required to respond to grid disturbances under high penetration of fluctuating and intermittent distributed energy resources (DERs) through extensive simulation studies. Specifically the following tasks were set to be accomplished: 1) Development of dynamic VAR compensator to support dynamic voltage variations on the grid through VAR control 2) Extensive testing of the DVC in the lab environment 3) Present the operational DVC device to the DOE at Varentec’s lab 4) Formulation of a detailed specification sheet, unit assembly document, test setup document, unit bring-up plan, and test plan 5) Extensive simulations of the DVC in a system with high PV penetration. Understanding the operation with many DVC on a single distribution system 6) Creation and submittal of quarterly and final reports conveying the design documents, unit performance data, modeling simulation charts and diagrams, and summary explanations of the satisfaction of program goals. This report details the various efforts that led to the development of the Fast DVC as well as the modeling & simulation results. The report begins with the introduction in Section II which outlines the

  17. Surface dynamics of amorphous polymers used for high-voltage insulators.

    Science.gov (United States)

    Shemella, Philip T; Laino, Teodoro; Fritz, Oliver; Curioni, Alessandro

    2011-11-24

    Amorphous siloxane polymers are the backbone of high-voltage insulation materials. The natural hydrophobicity of their surface is a necessary property for avoiding leakage currents and dielectric breakdown. As these surfaces are exposed to the environment, electrical discharges or strong mechanical impact can temporarily destroy their water-repellent properties. After such events, however, a self-healing process sets in and restores the original hydrophobicity within some hours. In the present study, we investigate possible mechanisms of this restoration process. Using large-scale, all-atom molecular dynamics simulations, we show that molecules on the material surface have augmented motion that allows them to rearrange with a net polarization. The overall surface region has a net orientation that contributes to hydrophobicity, and charged groups that are placed at the surface migrate inward, away from the vacuum interface and into the bulk-like region. Our simulations provide insight into the mechanisms for hydrophobic self-recovery that repair material strength and functionality and suggest material compositions for future high-voltage insulators.

  18. Compensation Strategy of Single Phase Dynamic Voltage Restorer Based on Self-learning Particle Swarm Optimization%基于自学习粒子群优化算法的单相动态电压恢复器补偿策略

    Institute of Scientific and Technical Information of China (English)

    韩文花; 沈晓晖; 徐俊; 陈旭; 贺帅鹏

    2013-01-01

    针对电压凹陷发生概率较高、危害大,严重影响电能质量的问题,通过理论分析和仿真实验,研究单相动态电压恢复器(dunamic voltage restorer,DVR)的补偿策略来改善电压凹陷,其内容主要包括对单相DVR已有的传统补偿策略进行理论分析与比较,并在此基础上提出一种基于自学习粒子群优化算法(self-learning particle swarm optimization,SLPSO)的优化补偿策略,通过仿真实验验证了该策略的正确性和可行性.

  19. Toward the Optimal Configuration of Dynamic Voltage Scaling Points in Real-Time Applications

    Institute of Scientific and Technical Information of China (English)

    Hui-Zhan Yi; Xue-Jun Yang

    2006-01-01

    In real-time applications, compiler-directed dynamic voltage scaling (DVS) could reduce energy consumption efficiently, where compiler put voltage scaling points in the proper places, and the supply voltage and clock frequency were adjusted to the relationship between the reduced time and the reduced workload. This paper presents the optimal configuration of dynamic voltage scaling points without voltage scaling overhead, which minimizes energy consumption. The conclusion is proved theoretically. Finally, it is confirmed by simulations with equally-spaced voltage scaling configuration.

  20. Restoration ecology: two-sex dynamics and cost minimization.

    Directory of Open Access Journals (Sweden)

    Ferenc Molnár

    Full Text Available We model a spatially detailed, two-sex population dynamics, to study the cost of ecological restoration. We assume that cost is proportional to the number of individuals introduced into a large habitat. We treat dispersal as homogeneous diffusion in a one-dimensional reaction-diffusion system. The local population dynamics depends on sex ratio at birth, and allows mortality rates to differ between sexes. Furthermore, local density dependence induces a strong Allee effect, implying that the initial population must be sufficiently large to avert rapid extinction. We address three different initial spatial distributions for the introduced individuals; for each we minimize the associated cost, constrained by the requirement that the species must be restored throughout the habitat. First, we consider spatially inhomogeneous, unstable stationary solutions of the model's equations as plausible candidates for small restoration cost. Second, we use numerical simulations to find the smallest rectangular cluster, enclosing a spatially homogeneous population density, that minimizes the cost of assured restoration. Finally, by employing simulated annealing, we minimize restoration cost among all possible initial spatial distributions of females and males. For biased sex ratios, or for a significant between-sex difference in mortality, we find that sex-specific spatial distributions minimize the cost. But as long as the sex ratio maximizes the local equilibrium density for given mortality rates, a common homogeneous distribution for both sexes that spans a critical distance yields a similarly low cost.

  1. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    Science.gov (United States)

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  2. Optimal placement of unified power flow controllers to improve dynamic voltage stability using power system variable based voltage stability indices.

    Science.gov (United States)

    Albatsh, Fadi M; Ahmad, Shameem; Mekhilef, Saad; Mokhlis, Hazlie; Hassan, M A

    2015-01-01

    This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs) in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs) including the line stability index (LQP), the voltage collapse proximity indicator (VCPI), and the line stability index (Lmn) are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD) software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO) and differential evolution (DE), which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches.

  3. Optimal placement of unified power flow controllers to improve dynamic voltage stability using power system variable based voltage stability indices.

    Directory of Open Access Journals (Sweden)

    Fadi M Albatsh

    Full Text Available This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs including the line stability index (LQP, the voltage collapse proximity indicator (VCPI, and the line stability index (Lmn are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO and differential evolution (DE, which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches.

  4. Optimal Placement of Unified Power Flow Controllers to Improve Dynamic Voltage Stability Using Power System Variable Based Voltage Stability Indices

    Science.gov (United States)

    Albatsh, Fadi M.; Ahmad, Shameem; Mekhilef, Saad; Mokhlis, Hazlie; Hassan, M. A.

    2015-01-01

    This study examines a new approach to selecting the locations of unified power flow controllers (UPFCs) in power system networks based on a dynamic analysis of voltage stability. Power system voltage stability indices (VSIs) including the line stability index (LQP), the voltage collapse proximity indicator (VCPI), and the line stability index (Lmn) are employed to identify the most suitable locations in the system for UPFCs. In this study, the locations of the UPFCs are identified by dynamically varying the loads across all of the load buses to represent actual power system conditions. Simulations were conducted in a power system computer-aided design (PSCAD) software using the IEEE 14-bus and 39- bus benchmark power system models. The simulation results demonstrate the effectiveness of the proposed method. When the UPFCs are placed in the locations obtained with the new approach, the voltage stability improves. A comparison of the steady-state VSIs resulting from the UPFCs placed in the locations obtained with the new approach and with particle swarm optimization (PSO) and differential evolution (DE), which are static methods, is presented. In all cases, the UPFC locations given by the proposed approach result in better voltage stability than those obtained with the other approaches. PMID:25874560

  5. Neutral-point voltage dynamic model of three-level NPC inverter for reactive load

    DEFF Research Database (Denmark)

    Maheshwari, Ram Krishan; Munk-Nielsen, Stig; Busquets-Monge, Sergio

    2012-01-01

    A three-level neutral-point-clamped inverter needs a controller for the neutral-point voltage. Typically, the controller design is based on a dynamic model. The dynamic model of the neutral-point voltage depends on the pulse width modulation technique used for the inverter. A pulse width modulati...

  6. Energy Conservation Using Dynamic Voltage Frequency Scaling for Computational Cloud

    Directory of Open Access Journals (Sweden)

    A. Paulin Florence

    2016-01-01

    Full Text Available Cloud computing is a new technology which supports resource sharing on a “Pay as you go” basis around the world. It provides various services such as SaaS, IaaS, and PaaS. Computation is a part of IaaS and the entire computational requests are to be served efficiently with optimal power utilization in the cloud. Recently, various algorithms are developed to reduce power consumption and even Dynamic Voltage and Frequency Scaling (DVFS scheme is also used in this perspective. In this paper we have devised methodology which analyzes the behavior of the given cloud request and identifies the associated type of algorithm. Once the type of algorithm is identified, using their asymptotic notations, its time complexity is calculated. Using best fit strategy the appropriate host is identified and the incoming job is allocated to the victimized host. Using the measured time complexity the required clock frequency of the host is measured. According to that CPU frequency is scaled up or down using DVFS scheme, enabling energy to be saved up to 55% of total Watts consumption.

  7. Energy Conservation Using Dynamic Voltage Frequency Scaling for Computational Cloud.

    Science.gov (United States)

    Florence, A Paulin; Shanthi, V; Simon, C B Sunil

    2016-01-01

    Cloud computing is a new technology which supports resource sharing on a "Pay as you go" basis around the world. It provides various services such as SaaS, IaaS, and PaaS. Computation is a part of IaaS and the entire computational requests are to be served efficiently with optimal power utilization in the cloud. Recently, various algorithms are developed to reduce power consumption and even Dynamic Voltage and Frequency Scaling (DVFS) scheme is also used in this perspective. In this paper we have devised methodology which analyzes the behavior of the given cloud request and identifies the associated type of algorithm. Once the type of algorithm is identified, using their asymptotic notations, its time complexity is calculated. Using best fit strategy the appropriate host is identified and the incoming job is allocated to the victimized host. Using the measured time complexity the required clock frequency of the host is measured. According to that CPU frequency is scaled up or down using DVFS scheme, enabling energy to be saved up to 55% of total Watts consumption.

  8. Dynamic range of low-voltage cascode current mirrors

    DEFF Research Database (Denmark)

    Bruun, Erik; Shah, Peter Jivan

    1995-01-01

    Low-voltage cascode current mirrors are reviewed with respect to the design limitations imposed if all transistors in the mirror are required to operate in the saturation region. It is found that both a lower limit and an upper limit exist for the cascode transistor bias voltage. Further, the use...

  9. High-voltage pulsed generator for dynamic fragmentation of rocks.

    Science.gov (United States)

    Kovalchuk, B M; Kharlov, A V; Vizir, V A; Kumpyak, V V; Zorin, V B; Kiselev, V N

    2010-10-01

    A portable high-voltage (HV) pulsed generator has been designed for rock fragmentation experiments. The generator can be used also for other technological applications. The installation consists of low voltage block, HV block, coaxial transmission line, fragmentation chamber, and control system block. Low voltage block of the generator, consisting of a primary capacitor bank (300 μF) and a thyristor switch, stores pulse energy and transfers it to the HV block. The primary capacitor bank stores energy of 600 J at the maximum charging voltage of 2 kV. HV block includes HV pulsed step up transformer, HV capacitive storage, and two electrode gas switch. The following technical parameters of the generator were achieved: output voltage up to 300 kV, voltage rise time of ∼50 ns, current amplitude of ∼6 kA with the 40 Ω active load, and ∼20 kA in a rock fragmentation regime (with discharge in a rock-water mixture). Typical operation regime is a burst of 1000 pulses with a frequency of 10 Hz. The operation process can be controlled within a wide range of parameters. The entire installation (generator, transmission line, treatment chamber, and measuring probes) is designed like a continuous Faraday's cage (complete shielding) to exclude external electromagnetic perturbations.

  10. A SCHEDULING SCHEME WITH DYNAMIC FREQUENCY CLOCKING AND MULTIPLE VOLTAGES FOR LOW POWER DESIGNS

    Institute of Scientific and Technical Information of China (English)

    Wen Dongxin; Wang Ling; Yang Xiaozong

    2007-01-01

    In this letter, a scheduling scheme based on Dynamic Frequency Clocking (DFC) and multiple voltages is proposed for low power designs under the timing and the resource constraints.Unlike the conventional methods at high level synthesis where only voltages of nodes were considered,the scheme based on a gain function considers both voltage and frequency simultaneously to reduce energy consumption. Experiments with a number of DSP benchmarks show that the proposed scheme achieves an effective energy reduction.

  11. Rotor Voltage Dynamics in the Doubly Fed Induction Generator During Grid Faults

    DEFF Research Database (Denmark)

    Lima, Francisco K. A.; Luna, Alvaro; Rodriguez, Pedro

    2010-01-01

    , something that would permit the injection of power to the grid during the fault, as the new grid codes demand. A theoretical study of the dynamical behavior of the rotor voltage is also developed, in order to show that the voltage at the rotor terminals required for the control strategy implementation...

  12. Location, Tilt, and Binding : A Molecular Dynamics Study of Voltage-Sensitive Dyes in Biomembranes

    NARCIS (Netherlands)

    Hinner, Marlon J.; Marrink, Siewert-J.; de Vries, Alex H.

    2009-01-01

    We present a molecular dynamics study on the interaction of styryl-type voltage-sensitive dyes with a lipid membrane. In this work, voltage-sensitive dyes are proposed as interesting model amphiphiles for biomolecular simulation, due to the wealth of biophysical and thermodynamical data available on

  13. Strongly nonlinear dynamics of electrolytes in large ac voltages

    DEFF Research Database (Denmark)

    Olesen, Laurits Højgaard; Bazant, Martin Z.; Bruus, Henrik

    2010-01-01

    We study the response of a model microelectrochemical cell to a large ac voltage of frequency comparable to the inverse cell relaxation time. To bring out the basic physics, we consider the simplest possible model of a symmetric binary electrolyte confined between parallel-plate blocking electrodes...... in the electrolyte near the electrodes and, at very large voltage, the breakdown of the quasiequilibrium structure of the double layers. The former leads to the prediction of “ac capacitive desalination” since there is a time-averaged transfer of salt from the bulk to the double layers, via oscillating diffusion...... nonlinear responses to large ac voltages, such as Faradaic reactions, electro-osmotic instabilities, and induced-charge electrokinetic phenomena....

  14. Dynamic in situ visualization of voltage-driven magnetic domain evolution in multiferroic heterostructures

    Science.gov (United States)

    Gao, Ya; Hu, Jia-Mian; Wu, Liang; Nan, C. W.

    2015-12-01

    Voltage control of magnetism in multiferroic heterostructures provides a promising solution to the excessive heating in spintronic devices. Direct observation of voltage-modulated magnetic domain evolution dynamics is desirable for studying the mechanism of the voltage control of magnetism at mesoscale, but has remained challenging. Here we explored a characterization method for the dynamic in situ evolution of pure voltage modulated magnetic domains in the heterostructures by employing the scanning Kerr microscopy function in the magneto optic Kerr effect system. The local magnetization reorientation of a Ni/PMN-PT heterostructure were characterized under sweeping applied voltage on the PMN-PT single crystal, and the results show that the magnetization rotation angle in the local regions is much greater than that obtained from macroscopic magnetization hysteresis loops.

  15. Predicting sports scoring dynamics with restoration and anti-persistence

    CERN Document Server

    Peel, Leto

    2015-01-01

    Professional team sports provide an excellent domain for studying the dynamics of social competitions. These games are constructed with simple, well-defined rules and payoffs that admit a high-dimensional set of possible actions and nontrivial scoring dynamics. The resulting gameplay and efforts to predict its evolution are the object of great interest to both sports professionals and enthusiasts. In this paper, we consider two online prediction problems for team sports:~given a partially observed game Who will score next? and ultimately Who will win? We present novel interpretable generative models of within-game scoring that allow for dependence on lead size (restoration) and on the last team to score (anti-persistence). We then apply these models to comprehensive within-game scoring data for four sports leagues over a ten year period. By assessing these models' relative goodness-of-fit we shed new light on the underlying mechanisms driving the observed scoring dynamics of each sport. Furthermore, in both p...

  16. Dynamical model of series-resonant converter with peak capacitor voltage predictor and switching frequency control

    Science.gov (United States)

    Pietkiewicz, A.; Tollik, D.; Klaassens, J. B.

    1989-08-01

    A simple small-signal low-frequency model of an idealized series resonant converter employing peak capacitor voltage prediction and switching frequency control is proposed. Two different versions of the model describe all possible conversion modes. It is found that step down modes offer better dynamic characteristics over most important network functions than do the step-up modes. The dynamical model of the series resonant converter with peak capacitor voltage prediction and switching frequency programming is much simpler than such popular control stategies as frequency VCO (voltage controlled oscillators) based control, or diode conduction angle control.

  17. Strongly nonlinear dynamics of electrolytes in large ac voltages

    CERN Document Server

    Olesen, Laurits H; Bruus, Henrik

    2009-01-01

    We study the response of a model micro-electrochemical cell to a large ac voltage of frequency comparable to the inverse cell relaxation time. To bring out the basic physics, we consider the simplest possible model of a symmetric binary electrolyte confined between parallel-plate blocking electrodes, ignoring any transverse instability or fluid flow. We analyze the resulting one-dimensional problem by matched asymptotic expansions in the limit of thin double layers and extend previous work into the strongly nonlinear regime, which is characterized by two novel features - significant salt depletion in the electrolyte near the electrodes and, at very large voltage, the breakdown of the quasi-equilibrium structure of the double layers. The former leads to the prediction of "ac capacitive desalination", since there is a time-averaged transfer of salt from the bulk to the double layers, via oscillating diffusion layers. The latter is associated with transient diffusion limitation, which drives the formation and co...

  18. Low Power, Reduced Dynamic Voltage Swing Domino Logic Circuits

    OpenAIRE

    Salendra.Govindarajulu; Dr.T.Jayachandra Prasad; Rangappa, P

    2010-01-01

    Dynamic domino logic circuits are widely used in modern digital VLSI circuits. These dynamic circuits are often favoured in high performance designs because of the speed advantage offered over static CMOS logic circuits. The main drawbacks of dynamic logic are a lack of design automation, a decreased tolerance to noise and increased power dissipation. In this work, new reduced – swing domino logic techniques which provide significant low power dissipation as compared to traditional domino cir...

  19. The Mattole River Estuary: Restoration Efforts in a Dynamic System

    Science.gov (United States)

    Barber, D.; Liquori, M.

    2010-12-01

    Despite extensive scientific advancement integrating our understanding of hydrology, geomorphology, and ecology in recent decades, the application of restoration in the field has been slow to evolve. This presentation will highlight 20 years of restoration practices in the Mattole River Estuary and how these practices have informed our understanding of this complex system. The Mattole River Watershed is a 304 square-mile basin located near the Mendocino Triple Junction in a remote region of California known as the “The Lost Coast” for its rugged mountains and undeveloped coastline. In addition to numerous species of fish, mammals, and over 250 bird species, the Mattole Watershed is home to three Federally-listed Threatened salmonids: California Coastal Chinook salmon, Southern Oregon/Northern California Coasts coho salmon, and Northern California steelhead trout. The 64 mile-long river meets the Pacific Ocean at the northern end of the 64,000 acre King Range National Conservation Area (KRNCA), managed by the Bureau of Land Management (BLM). The watershed is dynamic, with some of the nation’s highest annual rainfall (mean = 158 cm/yr), naturally occurring steep slopes, erosive sedimentary geology, and frequent earthquakes. All of these factors have amplified the negative effects of extensive logging and associated road building between 1945 and 1970, which left a legacy of increased sediment loads and high water temperatures that have yet to recover to pre-disturbance levels, severely impairing riparian and aquatic habitats. Prior to major land disturbances, the Mattole estuary/lagoon was notable for its deep, thermally-stratified pools and numerous functioning north and south bank slough channels that flushed sediments from the river and received marine water. As flows decline in late spring, a sandbar closes off surface flow from the river to the Pacific Ocean, forming a lagoon, which persists until flows increase in the fall. Today, the estuary is poor

  20. Dynamic Model of the Universal Motor Supplied by a Harmonic Voltage Dynamic Model of the Universal Motor Supplied by a Harmonic Voltage

    Directory of Open Access Journals (Sweden)

    Jan Dupej

    2005-01-01

    Full Text Available In present article a dynamic model of universal motors, based on the measured data is developed. Suppose that the supply voltage is harmonic and motor operate in open circuit loop. After representing of the mathematical model a simulation model based on the Matlab-Simulink is derived; this allows for the determination of the waveforms of the speed current and torque of the machine for different state operation. Induced voltage of the rotor is determined as a function of the magnetic core saturation and of the armature reaction.In present article a dynamic model of universal motors, based on the measured data is developed. Suppose that the supply voltage is harmonic and motor operate in open circuit loop. After representing of the mathematical model a simulation model based on the Matlab-Simulink is derived; this allows for the determination of the waveforms of the speed current and torque of the machine for different state operation. Induced voltage of the rotor is determined as a function of the magnetic core saturation and of the armature reaction.

  1. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields

    OpenAIRE

    Ye Peng; Tao Liu; Haifeng Gong; Xianming Zhang

    2016-01-01

    The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric...

  2. Voltage Dependence of Conformational Dynamics and Subconducting States of VDAC-1.

    Science.gov (United States)

    Briones, Rodolfo; Weichbrodt, Conrad; Paltrinieri, Licia; Mey, Ingo; Villinger, Saskia; Giller, Karin; Lange, Adam; Zweckstetter, Markus; Griesinger, Christian; Becker, Stefan; Steinem, Claudia; de Groot, Bert L

    2016-09-20

    The voltage-dependent anion channel 1 (VDAC-1) is an important protein of the outer mitochondrial membrane that transports energy metabolites and is involved in apoptosis. The available structures of VDAC proteins show a wide β-stranded barrel pore, with its N-terminal α-helix (N-α) bound to its interior. Electrophysiology experiments revealed that voltage, its polarity, and membrane composition modulate VDAC currents. Experiments with VDAC-1 mutants identified amino acids that regulate the gating process. However, the mechanisms for how these factors regulate VDAC-1, and which changes they trigger in the channel, are still unknown. In this study, molecular dynamics simulations and single-channel experiments of VDAC-1 show agreement for the current-voltage relationships of an "open" channel and they also show several subconducting transient states that are more cation selective in the simulations. We observed voltage-dependent asymmetric distortions of the VDAC-1 barrel and the displacement of particular charged amino acids. We constructed conformational models of the protein voltage response and the pore changes that consistently explain the protein conformations observed at opposite voltage polarities, either in phosphatidylethanolamine or phosphatidylcholine membranes. The submicrosecond VDAC-1 voltage response shows intrinsic structural changes that explain the role of key gating amino acids and support some of the current gating hypotheses. These voltage-dependent protein changes include asymmetric barrel distortion, its interaction with the membrane, and significant displacement of N-α amino acids.

  3. Nonequilibrium response of a voltage gated sodium ion channel and biophysical characterization of dynamic hysteresis.

    Science.gov (United States)

    Pal, Krishnendu; Das, Biswajit; Gangopadhyay, Gautam

    2017-02-21

    Here we have studied the dynamic as well as the non-equilibrium thermodynamic response properties of voltage-gated Na-ion channel. Using sinusoidally oscillating external voltage protocol we have both kinetically and energetically studied the non-equilibrium steady state properties of dynamic hysteresis in details. We have introduced a method of estimating the work done associated with the dynamic memory due to a cycle of oscillating voltage. We have quantitatively characterised the loop area of ionic current which gives information about the work done to sustain the dynamic memory only for ion conduction, while the loop area of total entropy production rate gives the estimate of work done for overall gating dynamics. The maximum dynamic memory of Na-channel not only depends on the frequency and amplitude but it also depends sensitively on the mean of the oscillating voltage and here we have shown how the system optimize the dynamic memory itself in the biophysical range of field parameters. The relation between the average ionic current with increasing frequency corresponds to the nature of the average dissipative work done at steady state. It is also important to understand that the utilization of the energy from the external field can not be directly obtained only from the measurement of ionic current but also requires nonequilibrium thermodynamic study.

  4. Voltage stability analysis of grid-connected wind farms with FACTS: Static and dynamic analysis

    Directory of Open Access Journals (Sweden)

    Kevin Zibran Heetun

    2016-01-01

    Full Text Available Recently, analysis of some major blackouts and failures of power system shows that voltage instability problem has been one of the main reasons of these disturbances and network collapses. In this article, a systematic approach to voltage stability analysis using various techniques for the IEEE 14-bus case study is presented. Static analysis is used to analyze the voltage stability of the system under study, while the dynamic analysis is used to evaluate the performance of compensators. The static techniques used are power flow, V–P curve analysis, and Q–V modal analysis. In this study, Flexible Alternating Current Transmission system (FACTS devices—namely, static synchronous compensators (STATCOMs and static var compensators (SVCs—are used as reactive power compensators, taking into account maintaining the violated voltage magnitudes of the weak buses within the acceptable limits defined in ANSI C84.1. Simulation results validate that both the STATCOMs and the SVCs can be effectively used to enhance the static voltage stability and increasing network loadability margin. Additionally, based on the dynamic analysis results, it has been shown that STATCOMs have superior performance, in dynamic voltage stability enhancement, compared to SVCs.

  5. Incorporating food web dynamics into ecological restoration: A modeling approach for river ecosystems

    Science.gov (United States)

    Bellmore, J. Ryan; Benjamin, Joseph R.; Newsom, Michael; Bountry, Jennifer A.; Dombroski, Daniel

    2017-01-01

    Restoration is frequently aimed at the recovery of target species, but also influences the larger food web in which these species participate. Effects of restoration on this broader network of organisms can influence target species both directly and indirectly via changes in energy flow through food webs. To help incorporate these complexities into river restoration planning we constructed a model that links river food web dynamics to in-stream physical habitat and riparian vegetation conditions. We present an application of the model to the Methow River, Washington (USA), a location of on-going restoration aimed at recovering salmon. Three restoration strategies were simulated: riparian vegetation restoration, nutrient augmentation via salmon carcass addition, and side-channel reconnection. We also added populations of nonnative aquatic snails and fish to the modeled food web to explore how changes in food web structure mediate responses to restoration. Simulations suggest that side-channel reconnection may be a better strategy than carcass addition and vegetation planting for improving conditions for salmon in this river segment. However, modeled responses were strongly sensitive to changes in the structure of the food web. The addition of nonnative snails and fish modified pathways of energy through the food web, which negated restoration improvements. This finding illustrates that forecasting responses to restoration may require accounting for the structure of food webs, and that changes in this structure—as might be expected with the spread of invasive species—could compromise restoration outcomes. Unlike habitat-based approaches to restoration assessment that focus on the direct effects of physical habitat conditions on single species of interest, our approach dynamically links the success of target organisms to the success of competitors, predators, and prey. By elucidating the direct and indirect pathways by which restoration affects target species

  6. Sediment dynamics in restored riparian forest with agricultural surroundings

    Science.gov (United States)

    Stucchi Boschi, Raquel; Cooper, Miguel; Alencar de Matos, Vitor; Ortega Gomes, Matheus; Ribeiro Rodrigues, Ricardo

    2017-04-01

    The riparian forests are considered Permanent Preservation Areas due to the ecological services provided by these forests. One of these services is the interception of the sediments before they reach the water bodies, which is essential to preserve water quality. The maintenance and restoration of riparian forests are mandatory, and the extent of these areas is defined based on water body width, following the Brazilian Forest Code. The method used to define the size of riparian forest areas elucidates the lack of accurate scientific data of the influence of the riparian forest in maintaining their ecological functions, particularly regarding the retention of sediments. In this study, we investigate the dynamics of erosion and sedimentation in restored riparian forests of a Semideciduous Tropical Forest situated in agricultural areas inserted in sugarcane landscapes in the state of São Paulo, Brazil. We defined two sites with soils of contrasting texture to monitor the dynamics and amount of deposited sediments. Site A is in the municipality of Araras and the soil is mainly clay. Site B is in the municipality of São Manuel and is dominated by sandy soils. In both areas, we defined plots to install graded metal stakes that were partially buried to monitor the dynamics of sediments. In site A, we defined eight plots and installed 27 metal stakes in each one. Three of the plots presented 30 m of riparian forest, two presented 15 m of riparian forest and three, 15 m of pasture followed by 15 m of forest. The design of the metal stakes was similar for all plots and was defined based on the type of erosion observed in site A. In site B, we defined seven points to monitor the sediments inside the reforested areas. Here, we observed erosive processes of great magnitude inside the forests, which results in a different design for the metal stakes. A total of nearly 150 metal stakes were installed to monitor these processes and also to verify the deposition in areas not yet

  7. Molecular Dynamics Simulations of Voltage Gated Cation Channels: Insights on Voltage-Sensor Domain Function and Modulation

    Directory of Open Access Journals (Sweden)

    Lucie eDelemotte

    2012-05-01

    Full Text Available Since their discovery in the 1950s, the structure and function of voltage gated cation channels (VGCC has been largely understood thanks to results stemming from electrophysiology, pharmacology, spectroscopy and structural biology. Over the past decade, computational methods such as molecular dynamics (MD simulations have also contributed, providing molecular level information that can be tested against experimental results, thereby allowing the validation of the models and protocols. Importantly, MD can shed light on elements of VGCC function that cannot be easily accessed through classical experiments. Here, we review the results of recent MD simulations addressing key questions that pertain to the function and modulation of the VGCC’s voltage sensor domain (VSD highlighting: 1 the movement of the S4-helix basic residues during channel activation, articulating how the electrical driving force acts upon them; 2 the nature of the VSD intermediate states on transitioning between open and closed states of the VGCC; and 3 the molecular level effects on the VSD arising from mutations of specific S4 positively charged residues involved in certain genetic diseases.

  8. Design to conditioning circuits of dynamic compensation of reactive power in the intelligence voltage controller

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>The paper introduces one design idea that making use of SCM to control Real-timely the dynamic compensation of reactive power.Firstly,design one Circuit to Sample the voltage and current,and by these datas we can easily calculate the power factor,and Voltage controller in the microcontroller to determine whether input the compensation capacitance according to the size of power factor,the paper also analyzes the principle of capacitance compensation and calculation method. Dynamic compensation for the entire process is quick and accurate.

  9. Dynamic magnetization switching and spin wave excitations by voltage-induced torque

    Science.gov (United States)

    Shiota, Yoichi

    2013-03-01

    The effect of electric fields on ultrathin ferromagnetic metal layer is one of the promising approaches for manipulating the spin direction with low-energy consumption, localization, and coherent behavior. Several experimental approaches to realize it have been investigated using ferromagnetic semiconductors, magnetostriction together with piezo-electric materials, multiferroic materials, and ultrathin ferromagnetic layer. In this talk, we will present a dynamic control of spins by voltage-induced torque. We used the magnetic tunnel junctions with ultrathin ferromagnetic layer, which shows voltage-induced perpendicular magnetic anisotropy change. By applying the voltage to the junction, the magnetic easy-axis in the ultrathin ferromagnetic layer changes from in-plane to out-of-plane, which causes a precession of the spins. This precession resulted in a two-way toggle switching by determining an appropriate pulse length. On the other hand, an application of rf-voltage causes an excitation of a uniform spin-wave. Since the precession of spin associates with an oscillation in the resistance of the junction, the applied rf-signal is rectified and produces a dc-voltage. From the spectrum of the dc-voltage as a function of frequency, we could estimate the voltage-induced torque. This research was supported by CREST-JST, G-COE program, and JSPS for the fellowship. Collaborators include T. Nozaki, S. Miwa, F. Bonell, N. Mizuochi, T. Shinjo, and Y. Suzuki.

  10. Dynamic performance of doubly-fed induction generator stator flux during consecutive grid voltage variations

    DEFF Research Database (Denmark)

    Zhu, Rongwu; Chen, Zhe; Wu, Xiaojie

    2015-01-01

    For the grid-connected doubly-fed induction generator (DFIG)-based wind turbine, because of the stator connected to the grid directly, the stator flux easily suffers from the effects of grid voltage variations, such as grid disturbances and grid faults. Moreover, since the magnetic field is excited...... by the rotor current, stator flux is also affected by the rotor current. Therefore this study systematically studies the dynamic performances of stator flux under consecutive grid voltage variations and varying rotor currents, and its influence on the performances of the DFIG during grid faults. The analyses...... reveal that the stator flux can be accumulated by the consecutive variations of the stator voltage, and the instants of grid voltage variations can lead to different amplitudes of the stator flux. In addition, the conventional vector control strategy and the active damping strategy are compared...

  11. A combined uninterruptible power supply and dynamic voltage compensator using a flywheel energy storage system

    Science.gov (United States)

    Weissbach, Robert Stephen

    Due to recent technological advances in materials, power electronics, magnetic bearings and controls, the flywheel energy storage system has become a viable alternative to electrochemical batteries. The advantages of the flywheel system are its higher power density, insensitivity to environmental conditions, lack of hazardous materials and ease of checking the charge. One potential use is in a power distribution system. The flywheel energy storage system may be used as both an uninterruptible power supply as well as a means of dynamic voltage compensation to protect critical loads on radial distribution feeders. To perform dynamic voltage compensation, a comparison was performed which shows that the series injection of power is preferable to the shunt injection of power in utilizing the available kVA of the flywheel system motor/generator. The system was designed and modeled using the Electromagnetic Transients Program to ensure a proper dynamic response of the flywheel energy storage system in either mode of operation. The design incorporates a boost converter on the dc link to enable the load voltage to be maintained as the flywheel spins down. The same boost converter also allows for extended operation in the series compensation mode, by implementing a novel control scheme where sinusoidal pulse width modulation control is used for to compensate for smaller supply voltage dips, while the boost converter is used to control the compensation for larger supply voltage dips.

  12. Dynamics and Collapse in a Power System Model with Voltage Variation: The Damping Effect

    Science.gov (United States)

    Ma, Jinpeng; Sun, Yong; Yuan, Xiaoming; Kurths, Jürgen; Zhan, Meng

    2016-01-01

    Complex nonlinear phenomena are investigated in a basic power system model of the single-machine-infinite-bus (SMIB) with a synchronous generator modeled by a classical third-order differential equation including both angle dynamics and voltage dynamics, the so-called flux decay equation. In contrast, for the second-order differential equation considering the angle dynamics only, it is the classical swing equation. Similarities and differences of the dynamics generated between the third-order model and the second-order one are studied. We mainly find that, for positive damping, these two models show quite similar behavior, namely, stable fixed point, stable limit cycle, and their coexistence for different parameters. However, for negative damping, the second-order system can only collapse, whereas for the third-order model, more complicated behavior may happen, such as stable fixed point, limit cycle, quasi-periodicity, and chaos. Interesting partial collapse phenomena for angle instability only and not for voltage instability are also found here, including collapse from quasi-periodicity and from chaos etc. These findings not only provide a basic physical picture for power system dynamics in the third-order model incorporating voltage dynamics, but also enable us a deeper understanding of the complex dynamical behavior and even leading to a design of oscillation damping in electric power systems. PMID:27832098

  13. Dynamic response characteristics analysis of the doubly-fed wind power system under grid voltage drop

    Science.gov (United States)

    Chen, Y.; Wang, J.; Wang, H. H.; Yang, L.; Chen, W.; Xu, Y. T.

    2016-08-01

    Double-fed induction generator (DFIG) is sensitive to the disturbances of grid, so the security and stability of the grid and the DFIG itself are under threat with the rapid increase of DFIG. Therefore, it is important to study dynamic response of the DFIG when voltage drop failure is happened in power system. In this paper, firstly, mathematical models and the control strategy about mechanical and electrical response processes is respectively introduced. Then through the analysis of response process, it is concluded that the dynamic response characteristics are related to voltage drop level, operating status of DFIG and control strategy adapted to rotor side. Last, the correctness of conclusion is validated by the simulation about mechanical and electrical response processes in different voltage levels drop and different DFIG output levels under DIgSILENT/PowerFactory software platform.

  14. Dynamic responses of a wind turbine drivetrain under turbulent wind and voltage disturbance conditions

    Directory of Open Access Journals (Sweden)

    Chengwu Li

    2016-05-01

    Full Text Available Wind energy is known as one of the most efficient clean renewable energy sources and has attracted extensive research interests in both academic and industry fields. In this study, the effects of turbulent wind and voltage disturbance on a wind turbine drivetrain are analyzed, and a wind turbine drivetrain dynamic model combined with the electric model of a doubly fed induction generator is established. The proposed model is able to account for the dynamic interaction between turbulent wind, voltage disturbance, and mechanical system. Also, the effects of time-varying meshing stiffness, transmission error, and bearing stiffness are included in the mechanical part of the coupled dynamic model. From the resultant model, system modes are computed. In addition, by considering the actual control strategies in the simulation process, the effects of turbulent wind and voltage disturbance on the geared rotor system are analyzed. The computational results show that the turbulent wind and voltage disturbance can cause adverse effects on the wind turbine drivetrain, especially the gearbox. A series of parametric studies are also performed to understand the influences of generator and gearbox parameters on the drivetrain system dynamics. Finally, the appropriate generator parameters having a positive effect on the gearbox in alleviating the extreme loads and the modeling approach for investigating the transient performance of generator are discussed.

  15. A new way of estimating compute-boundedness and its application to dynamic voltage scaling

    DEFF Research Database (Denmark)

    Venkatachalam, Vasanth; Franz, Michael; Probst, Christian W.

    2007-01-01

    Many dynamic voltage scaling algorithms rely on measuring hardware events (such as cache misses) for predicting how much a workload can be slowed down with acceptable performance loss. The events measured, however, are at best indirectly related to execution time and clock frequency. By relating...

  16. Dynamical Localization in a Two-Electron Quantum Dot Molecule Biased by a dc Voltage

    Institute of Scientific and Technical Information of China (English)

    王立民; 段素青; 赵宪庚; 刘承师; 马本堃

    2003-01-01

    We study the dynamics of two interacting electrons in a coupled-quantum-dot system with a time-dependent external electric field. The numerical results of the two-particle states reveal that the dynamical localization still exists under appropriate dc and ac voltage amplitudes. Such localization is different from the stationary localization phenomenon. Our conclusion is instructive for the field of quantum function devices.

  17. A method of dynamic chromatic aberration correction in low-voltage scanning electron microscopes.

    Science.gov (United States)

    Khursheed, Anjam

    2005-07-01

    A time-of-flight concept that dynamically corrects for chromatic aberration effects in scanning electron microscopes (SEMs) is presented. The method is predicted to reduce the microscope's chromatic aberration by an order of magnitude. The scheme should significantly improve the spatial resolution of low-voltage scanning electron microscopes (LVSEMs). The dynamic means of correcting for chromatic aberration also allows for the possibility of obtaining high image resolution from electron guns that have relatively large energy spreads.

  18. Dynamics of conductive and nonconductive particles under high-voltage electrostatic coupling fields

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    With the high-voltage electrostatic theory and numerical analysis, the dynamics of conductive and nonconductive particles under high-voltage electrostatic coupling fields was studied. The oscillation behavior of the conductive particle between the corona electrode and ground electrode was analyzed and its oscillation amplitude was Sm=(ta+ts)·νm/2. It was found that there was the "lift-off voltage (Ulo)" for the conductive particle between the electrostatic electrode and ground electrode. The concepts of "critical charged rotational speed (n?)", "detaching critical rotational speed of nonconductive particle (n′)" and "ratio of voltage and distance between surface of electrodes (U/D)" were presented and their criteria were established. The trajectories of the conductive particles under the coupling fields of the corona electrode, electrostatic electrode and ground electrode were simulated by the computer. The simulative results were in good agreement with the experimental ones. This research enriches the high-voltage electrostatic theory and provides a theoretic basis for optimization of operating parameters and structure design of high-voltage electrostatic separator.

  19. A Revive on 32×32 Bit Multiprecision Dynamic Voltage Scaling Multiplier with Operands Scheduler

    Directory of Open Access Journals (Sweden)

    Mrs.S.N.Rawat

    2016-02-01

    Full Text Available In this paper, we present a Multiprecision (MP reconfigurable multiplier that incorporates variable precision, parallel processing (PP, razor-based dynamic voltage scaling (DVS, and dedicated MP operands scheduling to provide optimum performance for a variety of operating conditions. All of the building blocks of the proposed reconfigurable multiplier can either work as independent smaller-precision multipliers or work in parallel to perform higher-precision multiplications. Given the user’s requirements (e.g., throughput, a dynamic voltage/ frequency scaling management unit configures the multiplier to operate at the proper precision and frequency. Adapting to the run-time workload of the targeted application, razor flip-flops together with a dithering voltage unit then configure the multiplier to achieve the lowest power consumption. The single-switch dithering voltage unit and razor flip-flops help to reduce the voltage safety margins and overhead typically associated to DVS to the lowest level. The large silicon area and power overhead typically associated to reconfigurability features are removed. Finally, the proposed novel MP multiplier can further benefit from an operands scheduler that rearranges the input data, hence to determine the optimum voltage and frequency operating conditions for minimum power consumption. This low-power MP multiplier is fabricated in AMIS 0.35-μm technology. Experimental results show that the proposed MP design features a 28.2% and 15.8% reduction in circuit area and power consumption compared with conventional fixed-width multiplier. When combining this MP design with error-tolerant razor-based DVS, PP, and the proposed novel operands scheduler, 77.7%–86.3% total power reduction is achieved with a total silicon area overhead as low as 11.1%. This paper successfully demonstrates that a MP architecture can allow more aggressive frequency/supply voltage scaling for improved power efficiency

  20. High-Dynamic-Range CT Reconstruction Based on Varying Tube-Voltage Imaging

    Science.gov (United States)

    2015-01-01

    For complicated structural components characterized by wide X-ray attenuation ranges, the conventional computed tomography (CT) imaging using a single tube-voltage at each rotation angle cannot obtain all structural information. This limitation results in a shortage of CT information, because the effective thickness of the components along the direction of X-ray penetration exceeds the limitation of the dynamic range of the X-ray imaging system. To address this problem, high-dynamic-range CT (HDR-CT) reconstruction is proposed. For this new method, the tube’s voltage is adjusted several times to match the corresponding effective thickness about the local information from an object. Then, HDR fusion and HDR-CT are applied to obtain the full reconstruction information. An accompanying experiment demonstrates that this new technology can extend the dynamic range of X-ray imaging systems and provide the complete internal structures of complicated structural components. PMID:26544723

  1. High-Dynamic-Range CT Reconstruction Based on Varying Tube-Voltage Imaging.

    Directory of Open Access Journals (Sweden)

    Ping Chen

    Full Text Available For complicated structural components characterized by wide X-ray attenuation ranges, the conventional computed tomography (CT imaging using a single tube-voltage at each rotation angle cannot obtain all structural information. This limitation results in a shortage of CT information, because the effective thickness of the components along the direction of X-ray penetration exceeds the limitation of the dynamic range of the X-ray imaging system. To address this problem, high-dynamic-range CT (HDR-CT reconstruction is proposed. For this new method, the tube's voltage is adjusted several times to match the corresponding effective thickness about the local information from an object. Then, HDR fusion and HDR-CT are applied to obtain the full reconstruction information. An accompanying experiment demonstrates that this new technology can extend the dynamic range of X-ray imaging systems and provide the complete internal structures of complicated structural components.

  2. Review of the Dynamics of Coalescence and Demulsification by High-Voltage Pulsed Electric Fields

    Directory of Open Access Journals (Sweden)

    Ye Peng

    2016-01-01

    Full Text Available The coalescence of droplets in oil can be implemented rapidly by high-voltage pulse electric field, which is an effective demulsification dehydration technological method. At present, it is widely believed that the main reason of pulse electric field promoting droplets coalescence is the dipole coalescence and oscillation coalescence in pulse electric field, and the optimal coalescence pulse electric field parameters exist. Around the above content, the dynamics of high-voltage pulse electric field promoting the coalescence of emulsified droplets is studied by researchers domestically and abroad. By review, the progress of high-voltage pulse electric field demulsification technology can get a better understanding, which has an effect of throwing a sprat to catch a whale on promoting the industrial application.

  3. Dynamic memory of a single voltage-gated potassium ion channel: A stochastic nonequilibrium thermodynamic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Banerjee, Kinshuk, E-mail: kbpchem@gmail.com [Department of Chemistry, University of Calcutta, 92 A.P.C. Road, Kolkata 700 009 (India)

    2015-05-14

    In this work, we have studied the stochastic response of a single voltage-gated potassium ion channel to a periodic external voltage that keeps the system out-of-equilibrium. The system exhibits memory, resulting from time-dependent driving, that is reflected in terms of dynamic hysteresis in the current-voltage characteristics. The hysteresis loop area has a maximum at some intermediate voltage frequency and disappears in the limits of low and high frequencies. However, the (average) dissipation at long-time limit increases and finally goes to saturation with rising frequency. This raises the question: how diminishing hysteresis can be associated with growing dissipation? To answer this, we have studied the nonequilibrium thermodynamics of the system and analyzed different thermodynamic functions which also exhibit hysteresis. Interestingly, by applying a temporal symmetry analysis in the high-frequency limit, we have analytically shown that hysteresis in some of the periodic responses of the system does not vanish. On the contrary, the rates of free energy and internal energy change of the system as well as the rate of dissipative work done on the system show growing hysteresis with frequency. Hence, although the current-voltage hysteresis disappears in the high-frequency limit, the memory of the ion channel is manifested through its specific nonequilibrium thermodynamic responses.

  4. Dynamical Symmetry Breaking of Maximally Generalized Yang-Mills Model and Its Restoration at Finite Temperatures

    Institute of Scientific and Technical Information of China (English)

    WANG Dian-Fu

    2008-01-01

    In terms of the Nambu-Jona-Lasinio mechanism, dynamical breaking of gauge symmetry for the maximally generalized Yang-Mills model is investigated. The gauge symmetry behavior at finite temperature is also investigated and it is shown that the gauge symmetry broken dynamically at zero temperature can be restored at finite temperatures.

  5. Dynamic Stability Analysis of Autonomous Medium-Voltage Mixed-Source Microgrid

    DEFF Research Database (Denmark)

    Zhao, Zhuoli; Yang, Ping; Guerrero, Josep M.

    2015-01-01

    In an autonomous microgrid without connection to the interconnected grid to support the frequency and voltage, it is more complex to control and manage. Thus in order to investigate the dynamic stability of the medium-voltage (MV) microgrid in Dongao Island, a detailed small-signal state......-space model of the autonomous MV mixed-source microgrid containing diesel generator set (DGS), grid-supporting battery energy storage system (BESS), squirrel cage induction generator (SCIG) wind turbine and network is developed. Sensitivity analysis is carried out to reveal the dynamic stability margin...... of the MV microgrid and identify the permissible variations range of the droop coefficients. Finally, the theoretical analysis is verified with time-domain simulation and experimental results....

  6. Voltage Stability Impact of Grid-Tied Photovoltaic Systems Utilizing Dynamic Reactive Power Control

    Science.gov (United States)

    Omole, Adedamola

    Photovoltaic (PV) DGs can be optimized to provide reactive power support to the grid, although this feature is currently rarely utilized as most DG systems are designed to operate with unity power factor and supply real power only to the grid. In this work, the voltage stability of a power system embedded with PV DG is examined in the context of the high reactive power requirement after a voltage sag or fault. A real-time dynamic multi-function power controller that enables renewable source PV DGs to provide the reactive power support necessary to maintain the voltage stability of the microgrid, and consequently, the wider power system is proposed. The loadability limit necessary to maintain the voltage stability of an interconnected microgrid is determined by using bifurcation analysis to test for the singularity of the network Jacobian and load differential equations with and without the contribution of the DG. The maximum and minimum real and reactive power support permissible from the DG is obtained from the loadability limit and used as the limiting factors in controlling the real and reactive power contribution from the PV source. The designed controller regulates the voltage output based on instantaneous power theory at the point-of-common coupling (PCC) while the reactive power supply is controlled by means of the power factor and reactive current droop method. The control method is implemented in a modified IEEE 13-bus test feeder system using PSCADRTM power system analysis software and is applied to the model of a Tampa ElectricRTM PV installation at Lowry Park Zoo in Tampa, FL. This dissertation accomplishes the systematic analysis of the voltage impact of a PV DG-embedded power distribution system. The method employed in this work bases the contribution of the PV resource on the voltage stability margins of the microgrid rather than the commonly used loss-of-load probability (LOLP) and effective load-carrying capability (ELCC) measures. The results of

  7. Dynamic Performance of a Back-to-Back HVDC Station Based on Voltage Source Converters

    Science.gov (United States)

    Khatir, Mohamed; Zidi, Sid-Ahmed; Hadjeri, Samir; Fellah, Mohammed-Karim

    2010-01-01

    The recent developments in semiconductors and control equipment have made the voltage source converter based high voltage direct current (VSC-HVDC) feasible. This new DC transmission is known as "HVDC Light or "HVDC Plus by leading vendors. Due to the use of VSC technology and pulse width modulation (PWM) the VSC-HVDC has a number of potential advantages as compared with classic HVDC. In this paper, the scenario of back-to-back VSC-HVDC link connecting two adjacent asynchronous AC networks is studied. Control strategy is implemented and its dynamic performances during disturbances are investigated in MATLAB/Simulink program. The simulation results have shown good performance of the proposed system under balanced and unbalanced fault conditions.

  8. Statistics of voltage drop in distribution circuits: a dynamic programming approach

    Energy Technology Data Exchange (ETDEWEB)

    Turitsyn, Konstantin S [Los Alamos National Laboratory

    2010-01-01

    We analyze a power distribution line with high penetration of distributed generation and strong variations of power consumption and generation levels. In the presence of uncertainty the statistical description of the system is required to assess the risks of power outages. In order to find the probability of exceeding the constraints for voltage levels we introduce the probability distribution of maximal voltage drop and propose an algorithm for finding this distribution. The algorithm is based on the assumption of random but statistically independent distribution of loads on buses. Linear complexity in the number of buses is achieved through the dynamic programming technique. We illustrate the performance of the algorithm by analyzing a simple 4-bus system with high variations of load levels.

  9. Dynamic Voltage Stability Studies using a Modified IEEE 30-Bus System

    Directory of Open Access Journals (Sweden)

    Oluwafemi Emmanuel Oni

    2016-09-01

    Full Text Available Power System stability is an essential study in the planning and operation of an efficient, economic, reliable and secure electric power system because it encompasses all the facet of power systems operations, from planning, to conceptual design stages of the project as well as during the systems operating life span. This paper presents different scenario of power system stability studies on a modified IEEE 30-bus system which is subjected to different faults conditions. A scenario whereby the longest high voltage alternating current (HVAC line is replaced with a high voltage direct current (HVDC line was implemented. The results obtained show that the HVDC line enhances system stability more compared to the contemporary HVAC line. Dynamic analysis using RMS simulation tool was used on DigSILENT PowerFactory.

  10. Research into the Effect of Supercapacitor Terminal Voltage on Regenerative Suspension Energy-Regeneration and Dynamic Performance

    Directory of Open Access Journals (Sweden)

    Ruochen Wang

    2017-01-01

    Full Text Available To study the effect of supercapacitor initial terminal voltage on the regenerative and semiactive suspension energy-regeneration and dynamic performance, firstly, the relationship between supercapacitor terminal voltage and linear motor electromagnetic damping force and that between supercapacitor terminal voltage and recycled energy by the supercapacitor in one single switching period were both analyzed. The result shows that the linear motor electromagnetic damping force is irrelevant to the supercapacitor terminal voltage, and the recycled energy by the supercapacitor reaches the maximum when initial terminal voltage of the supercapacitor equals output terminal voltage of the linear motor. Then, performances of system dynamics and energy-regeneration were studied as the supercapacitor initial terminal voltage varied in situations of B level and C level road. The result showed that recycled energy by the supercapacitor increased at first and then decreased while the dynamic performance had no obvious change. On the basis of previous study, a mode-switching control strategy of supercapacitor for the regenerative and semiactive suspension system was proposed, and the mode-switching rule was built. According to simulation and experiment results, the system energy-regeneration efficiency can be increased by utilizing the control strategy without influencing suspension dynamic performance, which is highly valuable to practical engineering.

  11. Voltage-induced pinnacle response in the dynamics of dielectric elastomers

    Science.gov (United States)

    Li, Bo; Zhang, Junshi; Chen, Hualing; Li, Dichen

    2016-05-01

    A dielectric elastomer is capable of large deformation under alternating electromechanical excitation. In this paper, several dynamic properties of a dielectric elastomer are investigated, in particular the effect of strain stiffening. A theoretical model is established that shows that the bias voltage affects the amplitude and the response waveform during vibration, a curve with the shape of a pinnacle. We also describe the underlying physical mechanism by considering the molecular chain length and cross-linking density of the material. A phase portrait is presented that reveals the transitional behavior of the dielectric elastomer as it switches between soft and stiffened vibration states.

  12. Reliable Dynamic Voltage Scaling for Real-Time Systems with Uncertain Execution Time and Resource Constraints

    Directory of Open Access Journals (Sweden)

    G. AZHAGUNILA,

    2011-02-01

    Full Text Available The main aim of this work is to develop a Dynamic Voltage Scaling (DVS algorithm for real- time system with resource constraints and the system thus developed is fault tolerant as well. The system is assumed to contain independent periodic tasks. Earliest Deadline Firstscheduling algorithm is considered in this. The algorithm helps in meeting the deadlines of all the tasks and also ensures that the total power consumption is minimized. The other objective is to develop a fault tolerant system. The proposed system is designed to handle hardware faults. Thus the proposed system is energy efficient and reliable.

  13. Ignition and dynamics of high-voltage glow discharge plasma implantation

    Science.gov (United States)

    Fu, Ricky K. Y.; Chu, Paul K.; Tian, X. B.; Yang, S. Q.

    2006-01-01

    The self-ignition and dynamics of glow discharge plasma in the pulsed high-voltage plasma immersion ion implantation mode have been investigated. After ignition during the pulse-on period, the glow discharge continues to be sustained for a long period of time after the high-voltage pulse has been turned off as monitored by a Langmuir probe. The glow discharge and ignition lie on the left side of the Paschen curve when pd (gas pressure times electrode separation) is adjusted by using different anode to cathode distances utilizing a conducting grounded grid. The increased or constant implantation current Ia reveals that the ion sheath is stable and conforms to the cathode structure as the plasma density increases by one to two orders of magnitude towards the anode. In addition, the duration of the post-pulse-off plasma can be as long as several times of the pulse duration. The ignition time and duration of the plasma depend on the working pressure, applied voltage and pulse duration.

  14. A dynamic simulation/optimization model for scheduling restoration of degraded military training lands.

    Science.gov (United States)

    Önal, Hayri; Woodford, Philip; Tweddale, Scott A; Westervelt, James D; Chen, Mengye; Dissanayake, Sahan T M; Pitois, Gauthier

    2016-04-15

    Intensive use of military vehicles on Department of Defense training installations causes deterioration in ground surface quality. Degraded lands restrict the scheduled training activities and jeopardize personnel and equipment safety. We present a simulation-optimization approach and develop a discrete dynamic optimization model to determine an optimum land restoration for a given training schedule and availability of financial resources to minimize the adverse effects of training on military lands. The model considers weather forecasts, scheduled maneuver exercises, and unique qualities and importance of the maneuver areas. An application of this approach to Fort Riley, Kansas, shows that: i) starting with natural conditions, the total amount of training damages would increase almost linearly and exceed a quarter of the training area and 228 gullies would be formed (mostly in the intensive training areas) if no restoration is carried out over 10 years; ii) assuming an initial state that resembles the present conditions, sustaining the landscape requires an annual restoration budget of $957 thousand; iii) targeting a uniform distribution of maneuver damages would increase the total damages and adversely affect the overall landscape quality, therefore a selective restoration strategy may be preferred; and iv) a proactive restoration strategy would be optimal where land degradations are repaired before they turn into more severe damages that are more expensive to repair and may pose a higher training risk. The last finding can be used as a rule-of-thumb for land restoration efforts in other installations with similar characteristics.

  15. Temporal dynamics of restored communities in ecological engineering works

    Science.gov (United States)

    Jaunatre, Renaud; Rey, Freddy

    2015-04-01

    Among the numerous applications of ecological engineering are the creation of engineering structures made of living materials, of which objective is to perform a function (for instance, erosion mitigation). One distinctive characteristic of these living materials is that they have their own dynamics. Within a plant community constituting an engineering structure, diversity and species abundance may change. It is well-known that changes of the community structure can have a significant effect on the whole functioning, and the provided services. This is therefore of primary concern to determine if spontaneous dynamics of these engineering structures allows the preservation of expected services. Our questions are: (i) How vegetation develops on these structures? (ii) How community functional traits are changing with time? and (iii) Is sedimentation control expected service still efficient after 12 years. The study site is the Durance catchment on Jurassic black marls where erosion has led to bare gullies. Since 2002, about 2000 ecological engineering structures have been made up in order to control sedimentation. In spring 2014, we sampled 664 of on which vegetation was recorded on 1m² plot. Plant community traits were a community weighted mean calculated from 13 species representing >60% of overall abundances for which we had values related to erosion control. Sediment control markers were also measured on each structures. NMDS and RDA were used to determine the effect of age on plant communities, traits and sediment control. The results show that during the first years age does not have an effect on plant community dynamics, functional traits related to erosion or erosion control markers of engineering structures. From the fields, stochastic events (decanal floods, small land slides, etc.) seems to play a more major role.

  16. Erosion and vegetation restoration impacts on ecosystem carbon dynamics in South China

    Science.gov (United States)

    Tang, X.; Liu, S.; Zhou, G.

    2010-01-01

    To quantify the consequences of erosion and vegetation restoration on ecosystem C dynamics (a key element in understanding the terrestrial C cycle), field measurements were collected since 1959 at two experimental sites set up on highly disturbed barren land in South China. One site had received vegetation restoration (the restored site) while the other received no planting and remained barren (the barren site). The Erosion-Deposition Carbon Model (EDCM) was used to simulate the ecosystem C dynamics at both sites. The on-site observations in 2007 showed that soil organic C (SOC) storage in the top 80-cm soil layer at the barren site was 50.3 ± 3.5 Mg C ha−1, half that of the restored site. The SOC and surface soil loss by erosion at the restored site from 1959 to 2007 was 3.7 Mg C ha−1 and 2.2 cm, respectively—one-third and one-eighth that of the barren site. The on-site C sequestration in SOC and vegetation at the restored site was 0.67 and 2.5 Mg C ha−1 yr−1, respectively, from 1959 to 2007, driven largely by tree growth and high atmospheric N deposition in the study area. Simulated findings suggested that higher N deposition resulted in higher on-site SOC storage in the soil profile (with SOC in the top 20-cm layer increasing more significantly), and higher on-site ecosystem C sequestration as long as N saturation was not reached. Lacking human-induced vegetation recovery, the barren site remained as barren land from 1959 to 2007 and the on-site C decrease was 0.28 Mg C ha−1 yr−1 Our study clearly indicated that vegetation restoration and burial by soil erosion provide a large potential C sink in terrestrial ecosystems.

  17. Influence of voltage magnitude on the dynamic behavior of a stable helium atmospheric pressure plasma jet

    Science.gov (United States)

    Ning, Wenjun; Wang, Lijun; Wu, Chen; Jia, Shenli

    2014-08-01

    Effects of voltage magnitude on the development of a stable helium atmospheric pressure plasma jet are investigated by current measurements and high temporal-resolution streak images. Generated by a coaxial dielectric barrier discharge structure, the entire discharge can be classified into three regions: discharges in the tube gap, downstream jet, and up-streamer. The discharge morphologies of each region are analyzed. In the positive discharge phase, there are two discharges in the tube gap between the electrodes; the first one is ignited as corona and then developed into streamer corona, and the second one is similar with positive glow. The downstream jet is ignited independently from the discharge in the tube gap. Referred as "plasma bullet," the dynamic behavior of the jet can be well described as a positive streamer. Under specific applied voltage, the jet is found to be composed by double bullets in which case the jet length decreases since that less charge is carried by the first bullet. The up-streamer can be captured as long as the discharge in the tube gap is activated. Propagating with velocity of ˜4 km/s, the up-streamer can be regarded as the extension of the first discharge in the tube gap. In the negative discharge phase, the discharge is confined in the tube gap with nearly symmetrical morphology with the positive one. Besides, with the rising of voltage, the negative discharge is initially intensified and then turns weaker after surpassing certain voltage, which may provide suitable condition for the occurrence of double-bullet phenomenon.

  18. MECHANISM OF RESTORATION OF THE DISPERSE FERRIFEROUS WASTE IN A DYNAMIC LAYER

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2015-01-01

    Full Text Available Some results of researches of processes of heating and restoration of the disperse materials containing iron in laboratory and semi-industrial conditions and the mechanism (physical model developed on the basis of the obtained data for the description of processes of solid-phase restoration of disperse ferriferous waste in a dynamic layer which can be considered as part of the solution of a task of development of technology of a low-tonnage recycling are presented in the article.Keywords. Recyclimg, the mechanism of solid recovery, dispersion metal wastes, rotary tilting furnaces.

  19. Stochastic Dynamics of Electrical Membrane with Voltage-Dependent Ion Channel Fluctuations

    CERN Document Server

    Qian, Hong; Qian, Min

    2014-01-01

    Brownian ratchet like stochastic theory for the electrochemical membrane system of Hodgkin-Huxley (HH) is developed. The system is characterized by a continuous variable $Q_m(t)$, representing mobile membrane charge density, and a discrete variable $K_t$ representing ion channel conformational dynamics. A Nernst-Planck-Nyquist-Johnson type equilibrium is obtained when multiple conducting ions have a common reversal potential. Detailed balance yields a previously unknown relation between the channel switching rates and membrane capacitance, bypassing Eyring-type explicit treatment of gating charge kinetics. From a molecular structural standpoint, membrane charge $Q_m$ is a more natural dynamic variable than potential $V_m$; our formalism treats $Q_m$-dependent conformational transition rates $\\lambda_{ij}$ as intrinsic parameters. Therefore in principle, $\\lambda_{ij}$ vs. $V_m$ is experimental protocol dependent,e.g., different from voltage or charge clamping measurements. For constant membrane capacitance pe...

  20. Evolution of foredune texture following dynamic restoration, Doughboy Bay, Stewart Island, New Zealand

    Science.gov (United States)

    Konlechner, T. M.; Ryu, W.; Hilton, M. J.; Sherman, D. J.

    2015-12-01

    Growing concern regarding the geomorphic and associated biotic effects of dune management practises has led to an increase in the number of dune restoration projects globally. Most recent projects aim to enhance the efficiency of aeolian sediment dynamics and increase dune mobility by decreasing vegetation cover, but we lack objective measures to evaluate such projects. Here we demonstrate the use of landscape metrics to quantify the evolution of foredune texture following the removal of vegetation. A long-term program of marram grass (Ammophila arenaria) eradication in southern New Zealand (Doughboy Bay, Stewart Island) is examined. Four metrics: bare sand area, patch adjacency, complexity, and the range of proximity, are used to classify a series of foredune textures beginning with the pre-restoration state through the phases of marram removal, to the current state. Foredune texture at Doughboy Bay has evolved from a semi-stable to an active state as the consequence of restoration. Two metrics, bare sand and adjacency, appear to be particularly good measures of change following marram removal. Patterns and rates of change for these metrics are consistent with ground observations of increased 'naturalness' (native plant communities, sand mobility) over the same period. The set of landscape metrics derived for Doughboy Bay were compared to similar sets measured for a nearby foredune system where marram invasion has not occurred, and where conditions presumably represent equilibrium foredune texture. Since the removal of marram at Doughboy Bay and the consequent remobilization of the sand surface, the foredune texture has increased in similarity to that of the reference site, indicating a favourable shift in plant cover as a result of the restoration program. We conclude that landscape metrics can be used to track changes in foredune morphology following restoration. Second, the planning, management, and monitoring of coastal dune restoration programs will benefit

  1. Restoration of motor defects caused by loss of Drosophila TDP-43 by expression of the voltage-gated calcium channel, Cacophony, in central neurons.

    Science.gov (United States)

    Lembke, Kayly M; Scudder, Charles; Morton, David B

    2017-08-28

    Defects in the RNA-binding protein, TDP-43, are known to cause a variety of neurodegenerative disease including amyotrophic lateral sclerosis (ALS) and frontotemporal lobar dementia (FTLD). A variety of experimental systems have shown that neurons are sensitive to TDP-43 expression levels, yet the specific functional defects resulting from TDP-43 dysregulation have not been well described. Using the Drosophila TDP-43 orthologue TBPH, we previously showed that TBPH null animals display locomotion defects as third instar larvae. Furthermore, loss of TBPH caused a reduction in cacophony, a type II voltage-gated calcium channel, expression and that genetically restoring cacophony in motor neurons in TBPH mutant animals was sufficient to rescue the locomotion defects. In the present study, we examined the relative contributions of NMJ physiology and the motor program to the locomotion defects and identified subsets of neurons that require cacophony expression to rescue the defects. At the NMJ, we showed mEPP amplitudes and frequency require TBPH. Cacophony expression in motor neurons rescued mEPP frequency but not mEPP amplitude. We also showed that TBPH mutants displayed reduced motor neuron bursting and coordination during crawling and restoring cacophony selectively in two pairs of cells located in the brain, the AVM001b/2b neurons, also rescued the locomotion and motor defects, but not the defects in NMJ physiology. These results suggest that the behavioral defects associated with loss of TBPH throughout the nervous system can be associated with defects in a small number of genes in a limited number of central neurons, rather than peripheral defects.SIGNIFICANCE STATEMENTTDP-43 dysfuction is a common feature in neurodegenerative diseases including ALS, FTLD, and Alzheimer's disease. Loss and gain of function models have shown neurons are sensitive to TDP-43 expression levels, but the specific defects caused by TDP-43 loss of function have not been described in

  2. Stability analysis and dynamic response of a DC-link module with a series voltage compensator

    DEFF Research Database (Denmark)

    Wang, Huai; Liu, Wenchao; Chung, Henry

    2013-01-01

    A DC-link module composed of a reduced value of DC-link capacitor and a series voltage compensator has been proposed. The voltage compensator processes the ripple voltage on the DC link and reactive power only, which can be implemented by low-voltage devices. The overall energy storage of the DC...

  3. Disease dynamics and potential mitigation among restored and wild staghorn coral, Acropora cervicornis

    Directory of Open Access Journals (Sweden)

    Margaret W. Miller

    2014-08-01

    Full Text Available The threatened status (both ecologically and legally of Caribbean staghorn coral, Acropora cervicornis, has prompted rapidly expanding efforts in culture and restocking, although tissue loss diseases continue to affect populations. In this study, disease surveillance and histopathological characterization were used to compare disease dynamics and conditions in both restored and extant wild populations. Disease had devastating effects on both wild and restored populations, but dynamics were highly variable and appeared to be site-specific with no significant differences in disease prevalence between wild versus restored sites. A subset of 20 haphazardly selected colonies at each site observed over a four-month period revealed widely varying disease incidence, although not between restored and wild sites, and a case fatality rate of 8%. A tropical storm was the only discernable environmental trigger associated with a consistent spike in incidence across all sites. Lastly, two field mitigation techniques, (1 excision of apparently healthy branch tips from a diseased colony, and (2 placement of a band of epoxy fully enclosing the diseased margin, gave equivocal results with no significant benefit detected for either treatment compared to controls. Tissue condition of associated samples was fair to very poor; unsuccessful mitigation treatment samples had severe degeneration of mesenterial filament cnidoglandular bands. Polyp mucocytes in all samples were infected with suspect rickettsia-like organisms; however, no bacterial aggregates were found. No histological differences were found between disease lesions with gross signs fitting literature descriptions of white-band disease (WBD and rapid tissue loss (RTL. Overall, our results do not support differing disease quality, quantity, dynamics, nor health management strategies between restored and wild colonies of A. cervicornis in the Florida Keys.

  4. Disease dynamics and potential mitigation among restored and wild staghorn coral, Acropora cervicornis.

    Science.gov (United States)

    Miller, Margaret W; Lohr, Kathryn E; Cameron, Caitlin M; Williams, Dana E; Peters, Esther C

    2014-01-01

    The threatened status (both ecologically and legally) of Caribbean staghorn coral, Acropora cervicornis, has prompted rapidly expanding efforts in culture and restocking, although tissue loss diseases continue to affect populations. In this study, disease surveillance and histopathological characterization were used to compare disease dynamics and conditions in both restored and extant wild populations. Disease had devastating effects on both wild and restored populations, but dynamics were highly variable and appeared to be site-specific with no significant differences in disease prevalence between wild versus restored sites. A subset of 20 haphazardly selected colonies at each site observed over a four-month period revealed widely varying disease incidence, although not between restored and wild sites, and a case fatality rate of 8%. A tropical storm was the only discernable environmental trigger associated with a consistent spike in incidence across all sites. Lastly, two field mitigation techniques, (1) excision of apparently healthy branch tips from a diseased colony, and (2) placement of a band of epoxy fully enclosing the diseased margin, gave equivocal results with no significant benefit detected for either treatment compared to controls. Tissue condition of associated samples was fair to very poor; unsuccessful mitigation treatment samples had severe degeneration of mesenterial filament cnidoglandular bands. Polyp mucocytes in all samples were infected with suspect rickettsia-like organisms; however, no bacterial aggregates were found. No histological differences were found between disease lesions with gross signs fitting literature descriptions of white-band disease (WBD) and rapid tissue loss (RTL). Overall, our results do not support differing disease quality, quantity, dynamics, nor health management strategies between restored and wild colonies of A. cervicornis in the Florida Keys.

  5. An energy-efficient, dynamic voltage scaling neural stimulator for a proprioceptive prosthesis.

    Science.gov (United States)

    Williams, Ian; Constandinou, Timothy G

    2013-04-01

    This paper presents an 8 channel energy-efficient neural stimulator for generating charge-balanced asymmetric pulses. Power consumption is reduced by implementing a fully-integrated DC-DC converter that uses a reconfigurable switched capacitor topology to provide 4 output voltages for Dynamic Voltage Scaling (DVS). DC conversion efficiencies of up to 82% are achieved using integrated capacitances of under 1 nF and the DVS approach offers power savings of up to 50% compared to the front end of a typical current controlled neural stimulator. A novel charge balancing method is implemented which has a low level of accuracy on a single pulse and a much higher accuracy over a series of pulses. The method used is robust to process and component variation and does not require any initial or ongoing calibration. Measured results indicate that the charge imbalance is typically between 0.05%-0.15% of charge injected for a series of pulses. Ex-vivo experiments demonstrate the viability in using this circuit for neural activation. The circuit has been implemented in a commercially-available 0.18 μm HV CMOS technology and occupies a core die area of approximately 2.8 mm(2) for an 8 channel implementation.

  6. Steric effects in the dynamics of electrolytes at large applied voltages: I. Double-layer charging

    CERN Document Server

    Kilic, M S; Ajdari, A; Kilic, Mustafa Sabri; Bazant, Martin Z.; Ajdari, Armand

    2006-01-01

    The classical Poisson-Boltzmann (PB) theory of electrolytes assumes a dilute solution of point charges with mean-field electrostatic forces. Even for very dilute solutions, however, it predicts absurdly large ion concentrations (exceeding close packing) for surface potentials of only a few tenths of a volt, which are often exceeded, e.g. in microfluidic pumps and electrochemical sensors. Since the 1950s, several modifications of the PB equation have been proposed to account for the finite size of ions in equilibrium, but in this two-part series, we consider steric effects on diffuse charge dynamics (in the absence of electro-osmotic flow). In this first part, we review the literature and analyze two simple models for the charging of a thin double layer, which must form a condensed layer of close-packed ions near the surface at high voltage. A surprising prediction is that the differential capacitance typically varies non-monotonically with the applied voltage, and thus so does the response time of an electrol...

  7. Robust low-dose dynamic cerebral perfusion CT image restoration via coupled dictionary learning scheme.

    Science.gov (United States)

    Tian, Xiumei; Zeng, Dong; Zhang, Shanli; Huang, Jing; Zhang, Hua; He, Ji; Lu, Lijun; Xi, Weiwen; Ma, Jianhua; Bian, Zhaoying

    2016-11-22

    Dynamic cerebral perfusion x-ray computed tomography (PCT) imaging has been advocated to quantitatively and qualitatively assess hemodynamic parameters in the diagnosis of acute stroke or chronic cerebrovascular diseases. However, the associated radiation dose is a significant concern to patients due to its dynamic scan protocol. To address this issue, in this paper we propose an image restoration method by utilizing coupled dictionary learning (CDL) scheme to yield clinically acceptable PCT images with low-dose data acquisition. Specifically, in the present CDL scheme, the 2D background information from the average of the baseline time frames of low-dose unenhanced CT images and the 3D enhancement information from normal-dose sequential cerebral PCT images are exploited to train the dictionary atoms respectively. After getting the two trained dictionaries, we couple them to represent the desired PCT images as spatio-temporal prior in objective function construction. Finally, the low-dose dynamic cerebral PCT images are restored by using a general DL image processing. To get a robust solution, the objective function is solved by using a modified dictionary learning based image restoration algorithm. The experimental results on clinical data show that the present method can yield more accurate kinetic enhanced details and diagnostic hemodynamic parameter maps than the state-of-the-art methods.

  8. System dynamic modelling to assess economic viability and risk trade-offs for ecological restoration in South Africa.

    Science.gov (United States)

    Crookes, D J; Blignaut, J N; de Wit, M P; Esler, K J; Le Maitre, D C; Milton, S J; Mitchell, S A; Cloete, J; de Abreu, P; Fourie nee Vlok, H; Gull, K; Marx, D; Mugido, W; Ndhlovu, T; Nowell, M; Pauw, M; Rebelo, A

    2013-05-15

    Can markets assist by providing support for ecological restoration, and if so, under what conditions? The first step in addressing this question is to develop a consistent methodology for economic evaluation of ecological restoration projects. A risk analysis process was followed in which a system dynamics model was constructed for eight diverse case study sites where ecological restoration is currently being pursued. Restoration costs vary across each of these sites, as do the benefits associated with restored ecosystem functioning. The system dynamics model simulates the ecological, hydrological and economic benefits of ecological restoration and informs a portfolio mapping exercise where payoffs are matched against the likelihood of success of a project, as well as a number of other factors (such as project costs and risk measures). This is the first known application that couples ecological restoration with system dynamics and portfolio mapping. The results suggest an approach that is able to move beyond traditional indicators of project success, since the effect of discounting is virtually eliminated. We conclude that systems dynamic modelling with portfolio mapping can guide decisions on when markets for restoration activities may be feasible.

  9. Voltage stability dynamical analysis by comparing static and dynamical loads; Estudio dinamico de estabilidad de tension comparando modelos de carga estatica y carga dinamica

    Energy Technology Data Exchange (ETDEWEB)

    Aromataris, Luis [Universidad Nacional de Rio Cuarto (UNRC) (Argentina); Arnera, Patricia; Riubrugent, Jean [Universidad Nacional de La Plata, Buenos Aires (Argentina). Facultad de Ingenieria. Instituto de Investigaciones Tecnologicas para Redes y Equipos Electricos

    2001-07-01

    This work investigate the impact produced by the load model on the voltage stability analysis of an electric system. Qualitative and quantitative analyses are approached in connection with the effects of modeling the electric loads by both dynamical and static way. Also it is highlighted the importance of using dynamical models of load, mainly when it is composed by motors.

  10. Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

    Science.gov (United States)

    Wilson, P. M.; Wilson, T. G.; Owen, H. A., Jr.

    1982-01-01

    Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated.

  11. Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

    Science.gov (United States)

    Wilson, P. M.; Wilson, T. G.; Owen, H. A., Jr.

    Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated.

  12. Multi-link faults localization and restoration based on fuzzy fault set for dynamic optical networks.

    Science.gov (United States)

    Zhao, Yongli; Li, Xin; Li, Huadong; Wang, Xinbo; Zhang, Jie; Huang, Shanguo

    2013-01-28

    Based on a distributed method of bit-error-rate (BER) monitoring, a novel multi-link faults restoration algorithm is proposed for dynamic optical networks. The concept of fuzzy fault set (FFS) is first introduced for multi-link faults localization, which includes all possible optical equipment or fiber links with a membership describing the possibility of faults. Such a set is characterized by a membership function which assigns each object a grade of membership ranging from zero to one. OSPF protocol extension is designed for the BER information flooding in the network. The BER information can be correlated to link faults through FFS. Based on the BER information and FFS, multi-link faults localization mechanism and restoration algorithm are implemented and experimentally demonstrated on a GMPLS enabled optical network testbed with 40 wavelengths in each fiber link. Experimental results show that the novel localization mechanism has better performance compared with the extended limited perimeter vector matching (LVM) protocol and the restoration algorithm can improve the restoration success rate under multi-link faults scenario.

  13. Dynamical characterization of inactivation path in voltage-gated Na(+) ion channel by non-equilibrium response spectroscopy.

    Science.gov (United States)

    Pal, Krishnendu; Gangopadhyay, Gautam

    2016-11-01

    Inactivation path of voltage gated sodium channel has been studied here under various voltage protocols as it is the main governing factor for the periodic occurrence and shape of the action potential. These voltage protocols actually serve as non-equilibrium response spectroscopic tools to study the ion channel in non-equilibrium environment. In contrast to a lot of effort in finding the crystal structure based molecular mechanism of closed-state(CSI) and open-state inactivation(OSI); here our approach is to understand the dynamical characterization of inactivation. The kinetic flux as well as energetic contribution of the closed and open- state inactivation path is compared here for voltage protocols, namely constant, pulsed and oscillating. The non-equilibrium thermodynamic quantities used in response to these voltage protocols serve as improved characterization tools for theoretical understanding which not only agrees with the previously known kinetic measurements but also predict the energetically optimum processes to sustain the auto-regulatory mechanism of action potential and the consequent inactivation steps needed. The time dependent voltage pattern governs the population of the conformational states which when couple with characteristic rate parameters, the CSI and OSI selectivity arise dynamically to control the inactivation path. Using constant, pulsed and continuous oscillating voltage protocols we have shown that during depolarization the OSI path is more favored path of inactivation however, in the hyper-polarized situation the CSI is favored. It is also shown that the re-factorisation of inactivated sodium channel to resting state occurs via CSI path. Here we have shown how the subtle energetic and entropic cost due to the change in the depolarization magnitude determines the optimum path of inactivation. It is shown that an efficient CSI and OSI dynamical profile in principle can characterize the open-state drug blocking phenomena.

  14. Dynamic Voltage Frequency Scaling Simulator for Real Workflows Energy-Aware Management in Green Cloud Computing.

    Science.gov (United States)

    Cotes-Ruiz, Iván Tomás; Prado, Rocío P; García-Galán, Sebastián; Muñoz-Expósito, José Enrique; Ruiz-Reyes, Nicolás

    2017-01-01

    Nowadays, the growing computational capabilities of Cloud systems rely on the reduction of the consumed power of their data centers to make them sustainable and economically profitable. The efficient management of computing resources is at the heart of any energy-aware data center and of special relevance is the adaptation of its performance to workload. Intensive computing applications in diverse areas of science generate complex workload called workflows, whose successful management in terms of energy saving is still at its beginning. WorkflowSim is currently one of the most advanced simulators for research on workflows processing, offering advanced features such as task clustering and failure policies. In this work, an expected power-aware extension of WorkflowSim is presented. This new tool integrates a power model based on a computing-plus-communication design to allow the optimization of new management strategies in energy saving considering computing, reconfiguration and networks costs as well as quality of service, and it incorporates the preeminent strategy for on host energy saving: Dynamic Voltage Frequency Scaling (DVFS). The simulator is designed to be consistent in different real scenarios and to include a wide repertory of DVFS governors. Results showing the validity of the simulator in terms of resources utilization, frequency and voltage scaling, power, energy and time saving are presented. Also, results achieved by the intra-host DVFS strategy with different governors are compared to those of the data center using a recent and successful DVFS-based inter-host scheduling strategy as overlapped mechanism to the DVFS intra-host technique.

  15. Sediment dynamics in restored riparian forest with different widths and agricultural surroundings

    Science.gov (United States)

    Stucchi Boschi, Raquel; Simões da Silva, Laura; Ribeiro Rodrigues, Ricardo; Cooper, Miguel

    2016-04-01

    The riparian forests are essential to maintaining the quality of water resources, aquifer recharge and biodiversity. Due to the ecological services provided by riparian forests, these areas are considered by the law as Permanent Preservation Areas, being mandatory maintenance and restoration. However, the obligation of restoration and the extent of the Permanent Preservation Areas as defined by the Brazilian Forest Code, based on water body width, elucidates the lack of accurate scientific data on the influence of the size of the riparian forest in maintaining their ecological functions, particularly regarding the retention of sediments. Studies that evaluate the ideal width of riparian forests to guarantee their ecological functions are scarce and not conclusive, especially when we consider newly restored forests, located in agricultural areas. In this study, we investigate the dynamics of erosion and sedimentation in restored riparian forests with different widths situated in agricultural areas. The two study areas are located in a Semideciduous Tropical Forest inserted in sugarcane landscapes of São Paulo state, Brazil. The installed plots had 60 and 100 m in length and the riparian forest has a width of 15, 30 and 50 m. The characteristics of the sediments inside the plots were evaluated by detailed morphological and micromorphological studies as well as physical characterization. The dynamics of deposition and the amount of deposited sediments have been assessed with graded metal stakes partially buried inside the plots. The intensity, frequency and distribution of rainfall, as well as the occurrence of extreme events, have been evaluated by data collected from rain gauges installed in the areas. We expect that smaller widths are not able to retain sediments originated from the adjacent sugarcane areas. We also believe that extreme events are responsible for generating most of the sediments. The results will be important to support the discussion about an

  16. Fine-tuning of voltage sensitivity of the Kv1.2 potassium channel by interhelix loop dynamics.

    Science.gov (United States)

    Sand, Rheanna; Sharmin, Nazlee; Morgan, Carla; Gallin, Warren J

    2013-04-01

    Many proteins function by changing conformation in response to ligand binding or changes in other factors in their environment. Any change in the sequence of a protein, for example during evolution, which alters the relative free energies of the different functional conformations changes the conditions under which the protein will function. Voltage-gated ion channels are membrane proteins that open and close an ion-selective pore in response to changes in transmembrane voltage. The charged S4 transmembrane helix transduces changes in transmembrane voltage into a change in protein internal energy by interacting with the rest of the channel protein through a combination of non-covalent interactions between adjacent helices and covalent interactions along the peptide backbone. However, the structural basis for the wide variation in the V50 value between different voltage-gated potassium channels is not well defined. To test the role of the loop linking the S3 helix and the S4 helix in voltage sensitivity, we have constructed a set of mutants of the rat Kv1.2 channel that vary solely in the length and composition of the extracellular loop that connects S4 to S3. We evaluated the effect of these different loop substitutions on the voltage sensitivity of the channel and compared these experimental results with molecular dynamics simulations of the loop structures. Here, we show that this loop has a significant role in setting the precise V50 of activation in Kv1 family channels.

  17. Tropical peatland carbon dynamics simulated for scenarios of disturbance and restoration and climate change

    Science.gov (United States)

    Frolking, S. E.; Warren, M.; Dai, Z.; Kurnianto, S.; Hagen, S. C.

    2015-12-01

    Tropical peatlands contain a globally significant carbon pool. Southeast Asian peatlands are being deforested, drained and burned at very high rates, mostly for conversion to industrial oil palm or pulp and paper plantations. The climate mitigation potential of tropical peatlands has gained increasing attention in recent years as persistent greenhouse gas emissions can be avoided or decreased if peatlands remain intact or are rehabilitated. In addition, peatland conservation or rehabilitation for climate mitigation also includes multiple co-benefits such as maintenance of ecosystem services, biodiversity, and air quality from reduced fire occurrence. Inventory guidelines and methodologies have only recently become available, and are based on few data from a limited number of sites. Few heuristic tools are available to evaluate the impact of management practices on carbon dynamics in tropical peatlands, and the potential climate mitigation benefits of peatland restoration. We used a process based dynamic tropical peatland model to explore the C dynamics of several peatland management trajectories represented by hypothetical scenarios, within the context of simulated 21st century climate change. All scenarios with land use, including those with optimal restoration, simulate C loss over the 21st century, with C losses ranging from 10% to essentially 100% of pre-disturbance values. Fire, either prescribed as part of a crop rotation cycle, or stochastic occurrences in sub-optimally managed degraded land can be the dominant C-loss pathway, particularly in the drier climate scenario we tested. A single 25-year oil palm rotation, with a prescribed initial burn, lost 40-50 kg C/m2, equivalent to accumulation during the previous 500 years, 10-30% of which was restored in 75 years of optimal restoration. Our results indicate that even under the most optimistic scenario of hydrological and forest restoration and the wettest climate regime, only about one-third of the carbon

  18. Supervisory hybrid model predictive control for voltage stability of power networks

    NARCIS (Netherlands)

    Negenborn, R.R.; Beccuti, A.G.; Demiray, T.; Leirens, S.; Damm, G.; De Schutter, B.; Morari, M.

    2007-01-01

    Emergency voltage control problems in electric power networks have stimulated the interest for the implementation of online optimal control techniques. Briefly stated, voltage instability stems from the attempt of load dynamics to restore power consumption beyond the capability of the transmission a

  19. A Dynamic Consensus Algorithm based Low-Voltage Ride-Through Operation of Power Converters in Grid-Interactive Microgrids

    DEFF Research Database (Denmark)

    Zhao, Xin; Meng, Lexuan; Savaghebi, Mehdi

    2016-01-01

    of the converters cannot be equally shared if no extra current balancing loop is added. Accordingly, a dynamic consensus algorithm (DCA) based negative/positive sequence current sharing scheme is proposed in this paper. Finally, a lab-scale AC microgrid was designed and tested in the lab to validate the feasibility...... control based voltage support strategy has been proposed to aid MGs riding through three phase asymmetrical voltage sags. However, since the line impedance from each converter to the point of common coupling (PCC) is not identical, both positive sequence and negative sequence output current...

  20. Systems and methods for process and user driven dynamic voltage and frequency scaling

    Science.gov (United States)

    Mallik, Arindam; Lin, Bin; Memik, Gokhan; Dinda, Peter; Dick, Robert

    2011-03-22

    Certain embodiments of the present invention provide a method for power management including determining at least one of an operating frequency and an operating voltage for a processor and configuring the processor based on the determined at least one of the operating frequency and the operating voltage. The operating frequency is determined based at least in part on direct user input. The operating voltage is determined based at least in part on an individual profile for processor.

  1. Capacitively coupled hydrogen plasmas sustained by tailored voltage waveforms: excitation dynamics and ion flux asymmetry

    Science.gov (United States)

    Bruneau, B.; Diomede, P.; Economou, D. J.; Longo, S.; Gans, T.; O'Connell, D.; Greb, A.; Johnson, E.; Booth, J.-P.

    2016-08-01

    Parallel plate capacitively coupled plasmas in hydrogen at relatively high pressure (~1 Torr) are excited with tailored voltage waveforms containing up to five frequencies. Predictions of a hybrid model combining a particle-in-cell simulation with Monte Carlo collisions and a fluid model are compared to phase resolved optical emission spectroscopy measurements, yielding information on the dynamics of the excitation rate in these discharges. When the discharge is excited with amplitude asymmetric waveforms, the discharge becomes electrically asymmetric, with different ion energies at each of the two electrodes. Unexpectedly, large differences in the \\text{H}2+ fluxes to each of the two electrodes are caused by the different \\text{H}3+ energies. When the discharge is excited with slope asymmetric waveforms, only weak electrical asymmetry of the discharge is observed. In this case, electron power absorption due to fast sheath expansion at one electrode is balanced by electron power absorption at the opposite electrode due to a strong electric field reversal.

  2. A dynamic Monte Carlo study of anomalous current voltage behaviour in organic solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Feron, K., E-mail: Krishna.Feron@csiro.au; Fell, C. J. [Centre for Organic Electronics, University of Newcastle, Callaghan, NSW 2308 (Australia); CSIRO Energy Flagship, Newcastle, NSW 2300 (Australia); Zhou, X.; Belcher, W. J.; Dastoor, P. C. [Centre for Organic Electronics, University of Newcastle, Callaghan, NSW 2308 (Australia)

    2014-12-07

    We present a dynamic Monte Carlo (DMC) study of s-shaped current-voltage (I-V) behaviour in organic solar cells. This anomalous behaviour causes a substantial decrease in fill factor and thus power conversion efficiency. We show that this s-shaped behaviour is induced by charge traps that are located at the electrode interface rather than in the bulk of the active layer, and that the anomaly becomes more pronounced with increasing trap depth or density. Furthermore, the s-shape anomaly is correlated with interface recombination, but not bulk recombination, thus highlighting the importance of controlling the electrode interface. While thermal annealing is known to remove the s-shape anomaly, the reason has been not clear, since these treatments induce multiple simultaneous changes to the organic solar cell structure. The DMC modelling indicates that it is the removal of aluminium clusters at the electrode, which act as charge traps, that removes the anomalous I-V behaviour. Finally, this work shows that the s-shape becomes less pronounced with increasing electron-hole recombination rate; suggesting that efficient organic photovoltaic material systems are more susceptible to these electrode interface effects.

  3. Dynamically tracking the joule heating effect on the voltage induced metal-insulator transition in VO2 crystal film

    Directory of Open Access Journals (Sweden)

    G. M. Liao

    2016-04-01

    Full Text Available Insulator to metal phase transitions driven by external electric field are one of the hottest topics in correlated oxide study. While this electric triggered phenomena always mixes the electric field switching effect and joule thermal effect together, which are difficult to clarify the intrinsic mechanism. In this paper, we investigate the dynamical process of voltage-triggered metal-insulator transition (MIT in a VO2 crystal film and observe the temperature dependence of the threshold voltages and switching delay times, which can be explained quite well based on a straightforward joule thermal model. By conducting the voltage controlled infrared transmittance measurement, the delayed infrared transmission change is also observed, further confirming the homogeneous switching process for a large-size film. All of these results show strong evidences that joule thermal effect plays a dominated role in electric-field-induced switching of VO2 crystal.

  4. Dynamically tracking the joule heating effect on the voltage induced metal-insulator transition in VO2 crystal film

    Science.gov (United States)

    Liao, G. M.; Chen, S.; Fan, L. L.; Chen, Y. L.; Wang, X. Q.; Ren, H.; Zhang, Z. M.; Zou, C. W.

    2016-04-01

    Insulator to metal phase transitions driven by external electric field are one of the hottest topics in correlated oxide study. While this electric triggered phenomena always mixes the electric field switching effect and joule thermal effect together, which are difficult to clarify the intrinsic mechanism. In this paper, we investigate the dynamical process of voltage-triggered metal-insulator transition (MIT) in a VO2 crystal film and observe the temperature dependence of the threshold voltages and switching delay times, which can be explained quite well based on a straightforward joule thermal model. By conducting the voltage controlled infrared transmittance measurement, the delayed infrared transmission change is also observed, further confirming the homogeneous switching process for a large-size film. All of these results show strong evidences that joule thermal effect plays a dominated role in electric-field-induced switching of VO2 crystal.

  5. Super-resolution restoration applied to the characterisation of dynamic surface changes on the Martian surface

    Science.gov (United States)

    Tao, Yu; Muller, Jan-Peter

    2016-10-01

    Higher spatial resolution imaging data is always desirable to the international community of planetary scientists interested in improving understanding of surface formation processes. We have previously developed a novel Super-resolution restoration (SRR) technique using Gotcha sub-pixel matching [Shin & Muller, PR, 2012], orthorectification, segmentation, and 4th order PDE-TV, called GPT SRR [Tao & Muller, PSS, 2016]. This technique is able to restore 5cm-12.5cm near rover scale images (Navcam at a range of ≥5m) from multi-angle repeat-pass 25cm resolution MRO HiRISE images [Tao & Muller, ISPRS, 2016].We have successfully applied the GPT-SRR to the MER and MSL missions (http://www.progisweb.eu), as well as the alleged site of the Beagle-2 spacecraft (https://www.flickr.com/photos/uclnews/albums/72157667609698345). In this work, we further apply GPT-SRR on areas with known dynamic changes, including Recurring Slope Lineae (RSL), Gullies, and Polar Dune Flows. We restore static surface and meanwhile track the dynamic features to characterise the "change", including directions and speed of the changes. We also demonstrate that such repeat images can be used to image the MER-A rover stuck in the sands.AcknowledgementsThe research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under iMars grant agreement no. 607379 as well as partial funding from the STFC "MSSL Consolidated Grant" ST/K000977/1.

  6. Dynamic Stability Improvement of Grid Connected DFIG Using Enhanced Field Oriented Control Technique for High Voltage Ride Through

    Directory of Open Access Journals (Sweden)

    V. N. Ananth Duggirala

    2015-01-01

    Full Text Available Doubly fed induction generator (DFIG is a better alternative to increased power demand. Modern grid regulations force DFIG to operate without losing synchronism during overvoltages called high voltage ride through (HVRT during grid faults. Enhanced field oriented control technique (EFOC was proposed in Rotor Side Control of DFIG converter to improve power flow transfer and to improve dynamic and transient stability. Further electromagnetic oscillations are damped, improved voltage mitigation and limit surge currents for sustained operation of DFIG during voltage swells. The proposed strategy has advantages such as improved reactive power control, better damping of electromagnetic torque oscillations, and improved continuity of voltage and current from stator and rotor to grid during disturbance. In EFOC technique, rotor flux reference changes its value from synchronous speed to zero during fault for injecting current at the rotor slip frequency. In this process, DC-Offset component of stator flux is controlled so that decomposition during overvoltage faults can be minimized. The offset decomposition of flux will be oscillatory in a conventional FOC, whereas in EFOC it is aimed to be quick damping. The system performance with overvoltage of 1.3 times, 1.62 times, and 2 times the rated voltage occurring is analyzed by using simulation studies.

  7. The influence of saltmarsh restoration on sediment dynamics and the potential impact on carbon sequestration

    Science.gov (United States)

    Taylor, Benjamin; Paterson, David

    2017-04-01

    Coastal wetland ecosystems can act as large-capacity carbon sinks, providing a valuable climate change mitigation function. Globally, saltmarshes are estimated to accumulate an average of 244.7g C m-2 yr-1 (Ouyang & Lee 2014). Saltmarsh areas have experienced rapid loss in the recent past of approximately 1-2% per year (Duarte et al. 2008). Efforts to restore these areas could result in additional carbon storage due to extended vegetation cover and altered burial due to changing sediment dynamics. The influence of restoration through transplantation on sediment dynamics within a small estuary on the east coast of Scotland was assessed. Restoration efforts have been implemented since the early 2000s providing examples of old established sites ("old", >10years), young recently planted sites ("young", business-as-usual' mudflats and natural marsh areas. In each of these area types seasonal data of sediment deposition and settlement were collected and sediment accretion rates measured. Deposition and settlement samples were taken four times a season, provided total sediment weight and organic content information. Elevation changes were measured once per season, quantifying sediment accretion rates. All data were collected between summer 2015 and spring 2016. Data suggest a positive correlation between sediment settlement and deposition quantities (dry weight) across the estuary (r2=0.64), with restored areas displaying a slightly stronger relationship (old r2=0.67, young r2=0.68) compared to natural marsh and mudflats (r2=0.54 and 0.59 respectively). Suggesting restored areas which are developing or expanding are retaining more from the potential sediment load in the water column. However average amounts of actual deposited material are significantly greater in mudflat and young areas with old and natural areas significantly lower; potentially as a result of those being of a lower elevation. Nevertheless, percentage organic matter content of deposited material is

  8. The Dynamic Fracture Process in Rocks Under High-Voltage Pulse Fragmentation

    Science.gov (United States)

    Cho, Sang Ho; Cheong, Sang Sun; Yokota, Mitsuhiro; Kaneko, Katsuhiko

    2016-10-01

    High-voltage pulse technology has been applied to rock excavation, liberation of microfossils, drilling of rocks, oil and water stimulation, cleaning castings, and recycling products like concrete and electrical appliances. In the field of rock mechanics, research interest has focused on the use of high-voltage pulse technology for drilling and cutting rocks over the past several decades. In the use of high-voltage pulse technology for drilling and cutting rocks, it is important to understand the fragmentation mechanism in rocks subjected to high-voltage discharge pulses to improve the effectiveness of drilling and cutting technologies. The process of drilling rocks using high-voltage discharge is employed because it generates electrical breakdown inside the rocks between the anode and cathode. In this study, seven rock types and a cement paste were electrically fractured using high-voltage pulse discharge to investigate their dielectric breakdown properties. The dielectric breakdown strengths of the samples were compared with their physical and mechanical properties. The samples with dielectric fractured were scanned using a high-resolution X-ray computed tomography system to observe the fracture formation associated with mineral constituents. The fracture patterns of the rock samples were analyzed using numerical simulation for high-voltage pulse-induced fragmentation that adopts the surface traction and internal body force conditions.

  9. Vegetation dynamics in Bishrampur collieries of northern Chhattisgarh, India: eco-restoration and management perspectives.

    Science.gov (United States)

    Kumar, A; Jhariya, M K; Yadav, D K; Banerjee, A

    2017-08-01

    Phytosociological study in and around reclaimed coal mine site is an essential requirement for judging restoration impact on a disturbed site. Various studies have been aimed towards assessing the impact of different restoration practices on coal mine wastelands. Plantation scheme in a scientific way is the most suitable approach in this context. During the present investigation, an effort have been made to assess the vegetation dynamics through structure, composition, diversity, and forest floor biomass analysis in and around Bishrampur collieries, Sarguja division, northern Chhattisgarh, India. We have tried to develop strategies for eco-restoration and habitat management of the concerned study sites. Four sites were randomly selected in different directions of the study area. We classified the vegetation community of the study sites into various strata on the basis of height. Two hundred forty quadrats were laid down in various directions of the study area to quantify vegetation under different strata. During our investigation, we found eight different tree species representing four families in the different study sites. The density of the various tree species ranged between 40 and 160 individuals ha(-1). The density of sapling, seedling, shrub, and herb ranged between 740 and 1620; 2000 and 6000; 1200 and 2000; and 484,000 and 612,000 individuals ha(-1), respectively, in different directions. The diversity indices of the tree reflected highest Shannon index value of 1.91. Simpsons index ranged between 0.28 and 0.50, species richness ranged between 0.27 and 0.61, equitability up to 1.44, and Beta diversity ranged between 2.00 and 4.00. Total forest floor biomass ranged between 4.20 and 5.65 t/ha among the study sites. Highest forest floor biomass occurred in the south direction and lowest at east direction. Total forest floor biomass declined by 6.19% in west, 13.10% in north, and 25.66% in east direction, respectively. The mining activities resulted

  10. Performance Evaluation of Three Different Inverter Configurations of DVR for Mitigation of Voltage Events

    Directory of Open Access Journals (Sweden)

    Miska Prasad

    2016-12-01

    Full Text Available The voltage events namely voltage sags and voltage swells represent the most common, frequent and important power quality events in today’s power system. Dynamic voltage restorer (DVR is one of the key components used to mitigate the supply voltage quality disturbances in terms of voltage sags and swells in the distribution system. It consists of an energy storage unit, a voltage source inverter, a filter, a coupling transformer and the control system. This paper presents three different inverter configurations of dynamic voltage restorer (DVR for mitigation of voltage events such as voltage sags and swells with sudden addition or removal of the nonlinear load. These three configurations are voltage source inverter based DVR (VSI-DVR, current source inverter based DVR (CSI-DVR and impedance or Z-source inverter based DVR (ZSI-DVR. The d-q control technique is used to control the operation of the DVR. The response of ZSI-DVR for mitigation of voltage sags and swells are investigated and compared with VSI-DVR and CSI-DVR using MATLAB/SIMULINK environment.

  11. Electron power absorption dynamics in capacitive radio frequency discharges driven by tailored voltage waveforms in CF4

    Science.gov (United States)

    Brandt, S.; Berger, B.; Schüngel, E.; Korolov, I.; Derzsi, A.; Bruneau, B.; Johnson, E.; Lafleur, T.; O'Connell, D.; Koepke, M.; Gans, T.; Booth, J.-P.; Donkó, Z.; Schulze, J.

    2016-08-01

    The power absorption dynamics of electrons and the electrical asymmetry effect in capacitive radio-frequency plasmas operated in CF4 and driven by tailored voltage waveforms are investigated experimentally in combination with kinetic simulations. The driving voltage waveforms are generated as a superposition of multiple consecutive harmonics of the fundamental frequency of 13.56 MHz. Peaks/valleys and sawtooth waveforms are used to study the effects of amplitude and slope asymmetries of the driving voltage waveform on the electron dynamics and the generation of a DC self-bias in an electronegative plasma at different pressures. Compared to electropositive discharges, we observe strongly different effects and unique power absorption dynamics. At high pressures and high electronegativities, the discharge is found to operate in the drift-ambipolar (DA) heating mode. A dominant excitation/ionization maximum is observed during sheath collapse at the edge of the sheath which collapses fastest. High negative-ion densities are observed inside this sheath region, while electrons are confined for part of the RF period in a potential well formed by the ambipolar electric field at this sheath edge and the collapsed (floating potential) sheath at the electrode. For specific driving voltage waveforms, the plasma becomes divided spatially into two different halves of strongly different electronegativity. This asymmetry can be reversed electrically by inverting the driving waveform. For sawtooth waveforms, the discharge asymmetry and the sign of the DC self-bias are found to reverse as the pressure is increased, due to a transition of the electron heating mode from the α-mode to the DA-mode. These effects are interpreted with the aid of the simulation results.

  12. Voltage-induced magnetization dynamics in CoFeB/MgO/CoFeB magnetic tunnel junctions

    Science.gov (United States)

    Miura, Katsuya; Yabuuchi, Shin; Yamada, Masaki; Ichimura, Masahiko; Rana, Bivas; Ogawa, Susumu; Takahashi, Hiromasa; Fukuma, Yasuhiro; Otani, Yoshichika

    2017-01-01

    Recent progress in magnetic tunnel junctions (MTJs) with a perpendicular easy axis consisting of CoFeB and MgO stacking structures has shown that magnetization dynamics are induced due to voltage-controlled magnetic anisotropy (VCMA), which will potentially lead to future low-power-consumption information technology. For manipulating magnetizations in MTJs by applying voltage, it is necessary to understand the coupled magnetization motion of two magnetic (recording and reference) layers. In this report, we focus on the magnetization motion of two magnetic layers in MTJs consisting of top layers with an in-plane easy axis and bottom layers with a perpendicular easy axis, both having perpendicular magnetic anisotropy. According to rectified voltage (Vrec) measurements, the amplitude of the magnetization motion depends on the initial angles of the magnetizations with respect to the VCMA direction. Our numerical simulations involving the micromagnetic method based on the Landau-Lifshitz-Gilbert equation of motion indicate that the magnetization motion in both layers is induced by a combination of VCMA and transferred angular momentum, even though the magnetic easy axes of the two layers are different. Our study will lead to the development of voltage-controlled MTJs having perpendicular magnetic anisotropy by controlling the initial angle between magnetizations and VCMA directions. PMID:28209976

  13. Voltage-induced magnetization dynamics in CoFeB/MgO/CoFeB magnetic tunnel junctions

    Science.gov (United States)

    Miura, Katsuya; Yabuuchi, Shin; Yamada, Masaki; Ichimura, Masahiko; Rana, Bivas; Ogawa, Susumu; Takahashi, Hiromasa; Fukuma, Yasuhiro; Otani, Yoshichika

    2017-02-01

    Recent progress in magnetic tunnel junctions (MTJs) with a perpendicular easy axis consisting of CoFeB and MgO stacking structures has shown that magnetization dynamics are induced due to voltage-controlled magnetic anisotropy (VCMA), which will potentially lead to future low-power-consumption information technology. For manipulating magnetizations in MTJs by applying voltage, it is necessary to understand the coupled magnetization motion of two magnetic (recording and reference) layers. In this report, we focus on the magnetization motion of two magnetic layers in MTJs consisting of top layers with an in-plane easy axis and bottom layers with a perpendicular easy axis, both having perpendicular magnetic anisotropy. According to rectified voltage (Vrec) measurements, the amplitude of the magnetization motion depends on the initial angles of the magnetizations with respect to the VCMA direction. Our numerical simulations involving the micromagnetic method based on the Landau-Lifshitz-Gilbert equation of motion indicate that the magnetization motion in both layers is induced by a combination of VCMA and transferred angular momentum, even though the magnetic easy axes of the two layers are different. Our study will lead to the development of voltage-controlled MTJs having perpendicular magnetic anisotropy by controlling the initial angle between magnetizations and VCMA directions.

  14. Dynamics of voltage source converter in a grid connected solar photovoltaic system

    DEFF Research Database (Denmark)

    Haribabu, Divyanagalakshmi; Vangari, Adithya; Sakamuri, Jayachandra N.

    2015-01-01

    This paper emphasises the modelling and control of a voltage source converter (VSC) for three phase grid connected PV system. The transfer functions for inner current control and outer DC link voltage control for VSC are derived. The controllers for VSC are designed based on PI and K factor contr...... conditions. The effectiveness of the proposed controller is illustrated by evaluating the response of PV system for power system voltage sag and swell conditions as well as grid faults.......This paper emphasises the modelling and control of a voltage source converter (VSC) for three phase grid connected PV system. The transfer functions for inner current control and outer DC link voltage control for VSC are derived. The controllers for VSC are designed based on PI and K factor control...... methods and the performance of VSC using both the methods are presented with the simulations performed using PSCAD/EMTDC. The design of LC filter to meet the specified THD requirement for grid connected VSC is presented and the corresponding harmonic analysis is performed for different solar radiation...

  15. Extraction and restoration of hippocampal spatial memories with nonlinear dynamical modeling

    Directory of Open Access Journals (Sweden)

    Dong eSong

    2014-05-01

    Full Text Available To build a cognitive prosthesis that can replace the memory function of the hippocampus, it is essential to model the input-output function of the damaged hippocampal region, so the prosthetic device can stimulate the downstream hippocampal region, e.g., CA1, with the output signal, e.g., CA1 spike trains, predicted from the ongoing input signal, e.g., CA3 spike trains, and the identified input-output function, e.g., CA3-CA1 model. In order for the downstream region to form appropriate long-term memories based on the restored output signal, furthermore, the output signal should contain sufficient information about the memories that the animal has formed. In this study, we verify this premise by applying regression and classification modelings of the spatio-temporal patterns of spike trains to the hippocampal CA3 and CA1 data recorded from rats performing a memory-dependent delayed nonmatch-to-sample (DNMS task. The regression model is essentially the multiple-input, multiple-output (MIMO nonlinear dynamical model of spike train transformation. It predicts the output spike trains based on the input spike trains and thus restores the output signal. In addition, the classification model interprets the signal by relating the spatio-temporal patterns to the memory events. We have found that: (1 both hippocampal CA3 and CA1 spike trains contain sufficient information for predicting the locations of the sample responses (i.e., left and right memories during the DNMS task; and more importantly (2 the CA1 spike trains predicted from the CA3 spike trains by the MIMO model also are sufficient for predicting the locations on a single-trial basis. These results show quantitatively that, with a moderate number of unitary recordings from the hippocampus, the MIMO nonlinear dynamical model is able to extract and restore spatial memory information for the formation of long-term memories and thus can serve as the computational basis of the hippocampal memory

  16. Extraction and restoration of hippocampal spatial memories with non-linear dynamical modeling.

    Science.gov (United States)

    Song, Dong; Harway, Madhuri; Marmarelis, Vasilis Z; Hampson, Robert E; Deadwyler, Sam A; Berger, Theodore W

    2014-01-01

    To build a cognitive prosthesis that can replace the memory function of the hippocampus, it is essential to model the input-output function of the damaged hippocampal region, so the prosthetic device can stimulate the downstream hippocampal region, e.g., CA1, with the output signal, e.g., CA1 spike trains, predicted from the ongoing input signal, e.g., CA3 spike trains, and the identified input-output function, e.g., CA3-CA1 model. In order for the downstream region to form appropriate long-term memories based on the restored output signal, furthermore, the output signal should contain sufficient information about the memories that the animal has formed. In this study, we verify this premise by applying regression and classification modelings of the spatio-temporal patterns of spike trains to the hippocampal CA3 and CA1 data recorded from rats performing a memory-dependent delayed non-match-to-sample (DNMS) task. The regression model is essentially the multiple-input, multiple-output (MIMO) non-linear dynamical model of spike train transformation. It predicts the output spike trains based on the input spike trains and thus restores the output signal. In addition, the classification model interprets the signal by relating the spatio-temporal patterns to the memory events. We have found that: (1) both hippocampal CA3 and CA1 spike trains contain sufficient information for predicting the locations of the sample responses (i.e., left and right memories) during the DNMS task; and more importantly (2) the CA1 spike trains predicted from the CA3 spike trains by the MIMO model also are sufficient for predicting the locations on a single-trial basis. These results show quantitatively that, with a moderate number of unitary recordings from the hippocampus, the MIMO non-linear dynamical model is able to extract and restore spatial memory information for the formation of long-term memories and thus can serve as the computational basis of the hippocampal memory prosthesis.

  17. [Dynamic changes of soil microbial biomass in the restoration process of shrub plantations in loess hilly area].

    Science.gov (United States)

    Xue, Sha; Liu, Guo-Bin; Dai, Quan-Hou; Li, Xiao-Li; Wu, Rui-Jun

    2008-03-01

    By the method of spatiotemporal substitution and taking a slope farmland and a natural Platycladus orientailis L. forest as the controls, this paper studied the dynamic changes of soil microbial biomass, microbial respiration, metabolic quotient (qCO2) and physicochemical properties under the Caragana korshinkii and Hippophae rhamnoides plantations with different restoration age in loess hilly area. The results showed that with the increasing restoration age of the shrubs, soil physicochemical properties improved obviously, and soil microbial biomass had a significant increase. After 7 years restoration of C. korshinkii plantation, soil microbial biomass C increased apparently, compared with that in farmland, and the increments after each 5-7 years were all significant. Microbial biomass N and P had no significant increase in the first 13 years but kept relatively stable in the 20-30 years restoration of C. korshinkii plantation, and were significantly higher than those in farmland but lower than those under P. orientailis plantation after 30 years restoration of C. korshinkii plantation. Soil microbial respiration was enhanced with the increasing restoration age of the shrubs, with the peak in the 20-25 years restoration. After then, it decreased rapidly, and bottomed out in the 30 years restoration. qCO2 was significantly higher under P. orientailis plantation than in farmland in the early periods of shrubs restoration, and then decreased rapidly. After 30 years restoration of C. korshinkii plantation, qCO2 was lower than that in farmland but still much higher than that under P. orientailis plantation. Different shrub plantations had different effects on soil properties. H. rhamnoides with the same restoration age of C. korshinkii contributed more to the increase of soil microbial biomass and respiration. There were significant correlations between the restoration age of test shrub plantations and the microbial biomass, qCO2, and physicochemical properties of

  18. Distributed Voltage Unbalance Compensation in Islanded Microgrids by Using Dynamic-Consensus-Algorithm

    DEFF Research Database (Denmark)

    Meng, Lexuan; Zhao, Xin; Tang, Fen;

    2016-01-01

    In islanded microgrids (MGs), distributed generators (DGs) can be employed as distributed compensators for improving the power quality in the consumer side. Two-level hierarchical control can be used for voltage unbalance compensation. Primary level, consisting of droop control and virtual...... impedance, can be applied to help the positive sequence active and reactive power sharing. Secondary level is used to assist voltage unbalance compensation. However, if distribution line differences are considered, the negative sequence current cannot be well shared among DGs. In order to overcome...

  19. A voltage-controlled silver nanograting device for dynamic modulation of transmitted light based on the surface plasmon polariton effect

    Science.gov (United States)

    Wang, Hailong; Li, Haibo; Wang, Yi; Xu, Shuping; Xu, Weiqing

    2016-02-01

    An active-controlled plasmonic device is designed and fabricated based on the index-sensitive properties of surface plasmon polaritons (SPPs). We utilize a one-dimensional silver nanograting with a period of 320 nm overlayered with a liquid crystal (LC) layer (50 μm in thickness), to transmit selectively the surface plasmon resonance (SPR) wavelength. This device realizes the active, reversible and continuous control of the transmitted light wavelength by modulating the external voltage signal applied to the LC layer. This voltage-controlled plasmonic filter has a dynamic wavelength modulation range of 17 nm, a fast respond speed of 4.24 ms and a low driving voltage of 1.06 V μm-1. This study opens up a unique way for the design of tunable nanophotonic devices, such as a micro light sources and switches.An active-controlled plasmonic device is designed and fabricated based on the index-sensitive properties of surface plasmon polaritons (SPPs). We utilize a one-dimensional silver nanograting with a period of 320 nm overlayered with a liquid crystal (LC) layer (50 μm in thickness), to transmit selectively the surface plasmon resonance (SPR) wavelength. This device realizes the active, reversible and continuous control of the transmitted light wavelength by modulating the external voltage signal applied to the LC layer. This voltage-controlled plasmonic filter has a dynamic wavelength modulation range of 17 nm, a fast respond speed of 4.24 ms and a low driving voltage of 1.06 V μm-1. This study opens up a unique way for the design of tunable nanophotonic devices, such as a micro light sources and switches. Electronic supplementary information (ESI) available: (1) The general theory of the VCP filter; (2) RI sensitivity; (3) the thickness optimization of the Ag grating sandwiched by photoresist layers; (4) image system; (5) detection systems for transmission and reflection spectra; (6) detection system for the response time of the VCP filter. See DOI: 10.1039/c5nr

  20. Effects of road salts on groundwater and surface water dynamics of socium and chloride in an urban restored stream

    Science.gov (United States)

    Road salts are a growing environmental concern in urban watersheds. We examined groundwater (GW) and surface water (SW) dynamics of Na+ and Cl− in Minebank Run (MBR), an urban stream in Maryland, USA. We observed an increasing salinity trend in this restored stream. Current basef...

  1. Incorporating food web dynamics into ecological restoration: a modeling approach for river ecosystems

    Science.gov (United States)

    J. Ryan Bellmore; Joseph R. Benjamin; Michael Newsom; Jennifer A. Bountry; Daniel Dombroski

    2017-01-01

    Restoration is frequently aimed at the recovery of target species, but also influences the larger food web in which these species participate. Effects of restoration on this broader network of organisms can influence target species both directly and indirectly via changes in energy flow through food webs. To help incorporate these complexities into river restoration...

  2. Capacitively coupled hydrogen plasmas sustained by tailored voltage waveforms: excitation dynamics and ion flux asymmetry

    NARCIS (Netherlands)

    Bruneau, B.; Diomede, P.; Economou, D. J.; Longo, S.; Gans, T.; O’Connell, D.; Greb, A.; Johnson, E.; Booth, J. P.

    2016-01-01

    Parallel plate capacitively coupled plasmas in hydrogen at relatively high pressure ( 1 Torr) are excited with tailored voltage waveforms containing up to five frequencies. Predictions of a hybrid model combining a particle-in-cell simulation with Monte Carlo collisions and a fluid model

  3. Structural Dynamics of an Isolated-Voltage Sensor Domain in Lipid Bilayer

    Science.gov (United States)

    Chakrapani, Sudha; Cuello, Luis G.; Cortes, Marien D.; Perozo, Eduardo

    2009-01-01

    Summary A strong interplay between the voltage-sensor domain (VSD) and the pore domain (PD) underlies voltage-gated channel functions. In a few voltage-sensitive proteins, the VSD has been shown to function without a canonical PD, although its structure and oligomeric state remain unknown. Here using EPR spectroscopy we show that the isolated-VSD of KvAP can remain monomeric in reconstituted bilayer and retain a transmembrane conformation. We find that water-filled crevices extend deep into the membrane around S3, a scaffold conducive to transport of proton/cations is intrinsic to the VSD. Differences in solvent accessibility in comparison to the full-length KvAP, allowed us to define an interacting footprint of the PD on the VSD. This interaction is centered around S1 and S2 and shows a rotation of 70–100° relative to Kv1.2-Kv2.1 chimera. Sequence-conservation patterns in Kv channels, Hv channels and voltage-sensitive phosphatases reveal several near-universal features suggesting a common molecular architecture for all VSDs. PMID:18334215

  4. Dynamics of threshold voltage shifts in organic and amorphous silicon field-effect transistors

    NARCIS (Netherlands)

    Mathijssen, Simon G. J.; Colle, Michael; Gomes, Henrique; Smits, Edsger C. P.; de Boer, Bert; McCulloch, Iain; Bobbert, Peter A.; de Leeuw, Dago M.; Cölle, Michael

    2007-01-01

    The electrical instability of organic field-effect transistors is investigated. We observe that the threshold-voltage shift (see figure) shows a stretched-exponential time dependence under an applied gate bias. The activation energy of 0.6 eV is common for our and all other organic transistors repor

  5. Intrinsic spin dynamics in optically excited nanoscale magnetic tunnel junction arrays restored by dielectric coating

    Science.gov (United States)

    Jaris, M.; Yahagi, Y.; Mahato, B. K.; Dhuey, S.; Cabrini, S.; Nikitin, V.; Stout, J.; Hawkins, A. R.; Schmidt, H.

    2016-11-01

    We report the all-optical observation of intrinsic spin dynamics and extraction of magnetic material parameters from arrays of sub-100 nm spin-transfer torque magnetic random access memory (STT-MRAM) devices with a CoFeB/MgO interface. To this end, the interference of surface acoustic waves with time-resolved magneto-optic signals via magneto-elastic coupling was suppressed using a dielectric coating. The efficacy of this method is demonstrated experimentally and via modeling on a nickel nanomagnet array. The magnetization dynamics for both coated nickel and STT-MRAM arrays shows a restored field-dependent Kittel mode from which the effective damping can be extracted. We observe an increased low-field damping due to extrinsic contributions from magnetic inhomogeneities and variations in the nanomagnet shape, while the intrinsic Gilbert damping remains unaffected by patterning. The data are in excellent agreement with a local resonance model and have direct implications for the design of STT-MRAM devices as well as other nanoscale spintronic technologies.

  6. An Improved Droop Control Method for DC Microgrids Based on Low Bandwidth Communication with DC Bus Voltage Restoration and Enhanced Current Sharing Accuracy

    DEFF Research Database (Denmark)

    Lu, Xiaonan; Guerrero, Josep M.; Sun, Kai;

    2014-01-01

    resistance in a droop-controlled dc microgrid, since the output voltage of each converter cannot be exactly the same, the output current sharing accuracy is degraded. Second, the DC bus voltage deviation increases with the load due to the droop action. In this paper, in order to improve the performance......, and the LBC system is only used for changing the values of the dc voltage and current. Hence, a decentralized control scheme is accomplished. The simulation test based on Matlab/Simulink and the experimental validation based on a 2×2.2 kW prototype were implemented to demonstrate the proposed approach....

  7. Organic Carbon Stocks, Dynamics and Restoration in Relation to Soils of Agroecosystems in Ethiopia: A Review

    Directory of Open Access Journals (Sweden)

    Getaneh Gebeyehu

    2017-02-01

    Full Text Available Soils represent the largest carbon pool and play important roles for carbon storage for prolonged periods in agroecosystems. A number of studies were conducted to quantify soil organic carbon (SOC worldwide. The objective of this review was to evaluate organic carbon stocks, dynamics and restoration in soils of agroecosystems in Ethiopia. Soil data from 32 different observations, representing four different agroecosystems, were analysed. The mean SOC stocks in the four agroecosystems varied and ranged from 25.66 (sub-humid agroecosystem to 113.17 (humid mid-highland agroecosystems Mg C ha-1 up to one meter depth. The trend of mean SOC followed (in descending order: humid mid-highland (113.17 Mg C ha-1 > per-humid highland (57.14 Mg C ha-1 > semi-arid (25.77 Mg C ha-1 > sub-humid (25.66 Mg C ha-1. Compared with soils of tropical countries, those in Ethiopian agroecosystems contained low SOC storage potential. This might be associated with differences in measurement and analysis methods as 53.1% of the studies employed the Walkley-Black Method, which is known to underestimate carbon stocks in addition to ecological and management effects. However, shifts of land management from rain-fed to irrigation farming systems exhibited progress in the improvement of mean SOC storage potential. The analyses showed that farming systems involving irrigation sequestered more carbon than rain-fed farm systems. The mean SOC in the various agricultural land uses followed the following trend (in descending order: agroforestry (153.57 Mg C ha-1 > grazing land (34.61 Mg C ha-1 > cereal cultivation (24.18 Mg C ha-1. Therefore, the possible solutions for improvement of organic carbon stocks would be implementation of appropriate restoration strategies based on agroecosystems.INTERNATIONAL JOURNAL OF ENVIRONMENT Volume-6, Issue-1, Dec-Feb 2016/17, page: 1-22 

  8. Dynamic Pull-In Investigation of a Clamped-Clamped Nanoelectromechanical Beam under Ramp-Input Voltage and the Casimir Force

    Directory of Open Access Journals (Sweden)

    Amir R. Askari

    2014-01-01

    Full Text Available The influence of the Casimir excitation on dynamic pull-in instability of a nanoelectromechanical beam under ramp-input voltage is studied. The ramp-input actuation has applications in frequency sweeping of RF-N/MEMS. The presented model is nonlinear due to the inherent nonlinearity of electrostatics and the Casimir excitations as well as the geometric nonlinearity of midplane stretching. A Galerkin based reduced order modeling is utilized. It is found that the calculated dynamic pull-in ramp input voltage leads to dynamic pull-in step input voltage by increasing the slope of voltage-time diagram. This fact is utilized to verify the results of present study.

  9. Size-dependent dynamic stability analysis of microbeams actuated by piezoelectric voltage based on strain gradient elasticity theory

    Energy Technology Data Exchange (ETDEWEB)

    Sahmani, Saeid; Bahrami, Mohsen [Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

    2015-01-15

    In the current paper, dynamic stability analysis of microbeams subjected to piezoelectric voltage is presented in which the microbeam is integrated with piezoelectric layers on the lower and upper surfaces. Both of the flutter and divergence instabilities of microbeams with clamped-clamped and clamped-free boundary conditions are predicted corresponding to various values of applied voltage. To take size effect into account, the classical Timoshenko beam theory in conjunction with strain gradient elasticity theory is utilized to develop nonclassical beam model containing three additional internal length scale parameters. By using Hamilton's principle, the higher-order governing differential equations and associated boundary conditions are derived. Afterward, generalized differential quadrature method is employed to discretize the size-dependent governing differential equations along with clamped-clamped and clamped-free end supports. The critical piezoelectric voltages corresponding to various values dimensionless length scale parameter are evaluated and compared with those predicted by the classical beam theory. It is revealed that in the case of clamped-free boundary conditions, the both of flutter and divergence instabilities occur. However, for the clamped-clamped microbeams, only divergence instability takes place.

  10. Vegetation development following stream/river restoration: more natural fluvial dynamics and morphology, return of aquatic and riparian plant species?

    Science.gov (United States)

    Soons, M. B.

    2012-04-01

    After centuries of human interventions in stream/river dynamics and morphology aimed at optimizing landscapes for agricultural and industrial purposes, new insights have inspired water managers to try and combine stream and river ecosystem functions with the conservation of biodiversity. Around the world, aquatic and riparian species have declined strongly due to pollution, destruction and fragmentation of their habitat, so that biodiversity conservation initiatives primarily focus on habitat restoration. In the past decades many stream and river restoration projects have been carried out and often hydrological dynamics and morphology have been restored to a more natural state. However, the successful restoration of aquatic and riparian habitats very often failed to result in restoration of their biodiversity. This lack of success from a biodiversity conservation perspective is usually attributed to 'dispersal limitation', meaning that the habitat may be restored, but species fail to reach the site and re-colonize it. Especially re-colonization by aquatic and riparian plant species is important, as such species function as ecosystem engineers: their presence alters fluvial dynamics and morphology, generates additional habitat heterogeneity and provides habitat and food for animal species. Following minor disturbances, re-colonization is often possible through locally remaining populations, by seeds in the seed bank or by surviving plant fragments. However, following major disturbances, colonization and establishment from other source populations are necessary. This usually occurs through dispersal of seeds (and in more aquatic species also by dispersal of vegetative fragments) into the restored wetland area. As dispersal occurs predominantly over short distances and source populations of aquatic and riparian species may be lacking in the surroundings, dispersal may be a limiting factor in the development of aquatic and riparian vegetation at a restored site. But

  11. Dynamic modeling and direct power control of wind turbine driven DFIG under unbalanced network voltage conditions

    Institute of Scientific and Technical Information of China (English)

    Jia-bing HU; Yi-kang HE; Lie XU

    2008-01-01

    This paper proposes an analysis and a direct power control (DPC) design of a wind turbine driven doubly-fed in-duction generator (DFIG) under unbalanced network voltage conditions. A DFIG model described in the positive and negative synchronous reference frames is presented. Variations of the stator output active and reactive powers are fully deduced in the presence of negative sequence supply voltage and rotor flux. An enhanced DPC scheme is proposed to eliminate stator active power oscillation during network unbalance. The proposed control scheme removes rotor current regulators and the decomposition processing of positive and negative sequence rotor currents. Simulation results using PSCAD/EMTDC are presented on a 2-MW DFIG wind power generation system to validate the feasibility of the proposed control scheme under balanced and unbalanced network conditions.

  12. Dynamic Consensus Algorithm based Distributed Voltage Harmonic Compensation in Islanded Microgrids

    DEFF Research Database (Denmark)

    Meng, Lexuan; Tang, Fen; Firoozabadi, Mehdi Savaghebi

    2015-01-01

    In islanded microgrids, the existence of nonlinear electric loads may cause voltage distortion and affect the performance of power quality sensitive equipment. Thanks to the prevalent utilization of interfacing power electronic devices and information/communication technologies, distributed...... generators can be employed as compensators to enhance the power quality on consumer side. However, conventional centralized control is facing obstacles because of the distributed fashion of generation and consumption. Accordingly, this paper proposes a consensus algorithm based distributed hierarchical...... control to realize voltage harmonic compensation and accurate current sharing in multi-bus islanded microgrids. Low order harmonic components are considered as examples in this paper. Harmonic current sharing is also realized among distributed generators by applying the proposed methods. Plug...

  13. Effect of voltage dynamics on response properties in a model of sensory hair cell

    CERN Document Server

    Amro, Rami

    2012-01-01

    Sensory hair cells in auditory and vestibular organs rely on active mechanisms to achieve high sensitivity and frequency selectivity. Recent experimental studies have documented self-sustained oscillations in hair cells of lower vertebrates on two distinct levels. First, the hair bundle can undergo spontaneous mechanical oscillations. Second, somatic electric voltage oscillations across the baso-lateral membrane of the hair cell have been observed. We develop a biophysical model of the bullfrog's saccular hair cell consisting of two compartments, mechanical and electrical, to study how the mechanical and the voltage oscillations interact to produce coherent self-sustained oscillations and how this interaction contributes to the overall sensitivity and selectivity of the hair cell. The model incorporates nonlinear mechanical stochastic hair bundle system coupled bi-directionally to a Hodgkin-Huxley type system describing somatic ionic currents. We isolate regions of coherent spontaneous oscillations in the par...

  14. Dynamic scaling of the restoration of rotational symmetry in Heisenberg quantum antiferromagnets

    Science.gov (United States)

    Weinberg, Phillip; Sandvik, Anders W.

    2017-08-01

    We apply imaginary-time evolution with the operator e-τ H to study relaxation dynamics of gapless quantum antiferromagnets described by the spin-rotation-invariant Heisenberg Hamiltonian H . Using quantum Monte Carlo simulations to obtain unbiased results, we propagate an initial state with maximal order parameter msz (the staggered magnetization) in the z spin direction and monitor the expectation value 〈ms〉 as a function of imaginary time τ . Results for different system sizes (lengths) L exhibit an initial essentially size independent relaxation of 〈ms〉 toward its value in the infinite-size spontaneously symmetry broken state, followed by a strongly size dependent final decay to zero when the O (3 ) rotational symmetry of the order parameter is restored. We develop a generic finite-size scaling theory that shows the relaxation time diverges asymptotically as Lz, where z is the dynamic exponent of the low-energy excitations. We use the scaling theory to develop a practical way of extracting the dynamic exponent from the numerical finite-size data, systematically eliminating scaling corrections. We apply the method to spin-1 /2 Heisenberg antiferromagnets on two different lattice geometries: the standard two-dimensional (2D) square lattice and a site-diluted 2D square lattice at the percolation threshold. In the 2D case we obtain z =2.001 (5 ) , which is consistent with the known value z =2 , while for the site-diluted lattice we find z =3.90 (1 ) or z =2.056 (8 ) Df , where Df=91 /48 is the fractal dimensionality of the percolating system. This is an improvement on previous estimates of z ≈3.7 . The scaling results also show a fundamental difference between the two cases; for the 2D square lattice, the data can be collapsed onto a common scaling function even when 〈ms〉 is relatively large, reflecting the Anderson tower of quantum rotor states with a common dynamic exponent z =2 . For the diluted 2D square lattice, the scaling works well only for

  15. Dynamical symmetry restoration for a higher-derivative four-fermion model in an external electromagnetic field

    CERN Document Server

    Elizalde, E; Odintsov, S D; Shilnov, Yu I; Shil'nov, Yu. I.

    1998-01-01

    A four-fermion model with additional higher-derivative terms is investigated in an external electromagnetic field. The effective potential in the leading order of large-N expansion is calculated in external constant magnetic and electric fields. It is shown that, in contrast to the former results concerning the universal character of "magnetic catalysis" in dynamical symmetry breaking, in the present higher-derivative model the magnetic field restores chiral symmetry broken initially on the tree level. Numerical results describing a second-order phase transition that accompanies the symmetry restoration at the quantum level are presented.

  16. Real-Time Nanoscale Open-Circuit Voltage Dynamics of Perovskite Solar Cells.

    Science.gov (United States)

    Garrett, Joseph L; Tennyson, Elizabeth M; Hu, Miao; Huang, Jinsong; Munday, Jeremy N; Leite, Marina S

    2017-04-12

    Hybrid organic-inorganic perovskites based on methylammonium lead (MAPbI3) are an emerging material with great potential for high-performance and low-cost photovoltaics. However, for perovskites to become a competitive and reliable solar cell technology their instability and spatial variation must be understood and controlled. While the macroscopic characterization of the devices as a function of time is very informative, a nanoscale identification of their real-time local optoelectronic response is still missing. Here, we implement a four-dimensional imaging method through illuminated heterodyne Kelvin probe force microscopy to spatially (perovskite solar cells in a low relative humidity environment. Local open-circuit voltage (Voc) images show nanoscale sites with voltage variation >300 mV under 1-sun illumination. Surprisingly, regions of voltage that relax in seconds and after several minutes consistently coexist. Time-dependent changes of the local Voc are likely due to intragrain ion migration and are reversible at low injection level. These results show for the first time the real-time transient behavior of the Voc in perovskite solar cells at the nanoscale. Understanding and controlling the light-induced electrical changes that affect device performance are critical to the further development of stable perovskite-based solar technologies.

  17. [Nutrient dynamics over the past 100 years and its restoration baseline in Dianshan Lake].

    Science.gov (United States)

    Li, Xiao-Ping; Chen, Xiao-Hua; Dong, Xu-Hui; Dong, Zhi; Sun, Dun-Ping

    2012-10-01

    The restoration of eutrophic lakes requires a good knowledge on the history and baseline of nutrients in the lakes. This work conducted an analysis on 210Pb/137Cs, water content, loss-on-ignition, sedimentary total phosphorus (TP), total nitrogen (TN), total organic carbon (TOC) and diatoms in the four sediment cores from Dianshan Lake (near Shanghai City). Good coherence in palaeoproxies between the cores indicates a relatively stable sedimentary environment. With increasing human impact, diatom communities shifted from oligo-trophic species Cyclotella bodanica, C. ocelata, Achnanthes minutissima, Cocconeis placentula var lineate, Cymbella sp. , Fragilaria pintata, F. brevistrata, F. construens var venter to recent eutrophic species including Cyclostephanos dubias, C. atomus, Stephanodiscus minitulus, S. hantzschi, Aulacoseria alpigena. The epilimnetic TP over the past 100 years reconstructed using an established diatom-TP transfer function matches well with the monitoring TP where exists. Based on the sedimentary nutrient characteristics and diatom-reconstructed nutrient dynamics, we proposed that the nutrient baseline for Dianshan Lake is 50-60 microg x L(-1), 500 mg x kg(-1) and 550 mg x kg(-1) for water TP concentration, sedimentary TP and TN, respectively.

  18. Characteristic of Soil Hydro-Physical Properties and Water Dynamics under Different Vegetation Restoration Types

    Institute of Scientific and Technical Information of China (English)

    MA Zelong; GONG Yuanbo; HU Tingxing

    2006-01-01

    By combining the observation of the soil profile at field and the chemical and physical analysis in laboratory, a study on the hydro-physical properties of soil in six different vegetation types and the dynamics of water content after rain was conducted in Wanchanggou, Guangyuan City to find out the vegetation types with effective water-conservation functions in order to serve the ecological restoration in the low hill heavy rain area upper the Jialing River. Results showed that:the hydro-physical properties of soil in the mixed Alnus cremastogyne and Cupressua Leyland forest (AcCl) were best. But in the depth of 0-20 cm. The properties of soil in the abandoned cropland (Fm) was better than that in the AcCl. The soil bulk densities varied significantly between the layers of 0-20 cm and 20-40 cm in all the six vegetation types except that in the Robinia pseudoacacia shrub forest (RpⅡ), and the changes of the maximum and the capillary moisture capacity between layers were significant only in the Fm and in the AcCl. Of these stands, the AcCl had the shortest water-absorbing period and the strongest moisture changes in the upper layer (0-15 cm). In the same stand, the deeper the soil layer, the slighter the soil moisture varied, and the longer the soil moisture accumulating process lasted.

  19. Local community detection as pattern restoration by attractor dynamics of recurrent neural networks.

    Science.gov (United States)

    Okamoto, Hiroshi

    2016-08-01

    Densely connected parts in networks are referred to as "communities". Community structure is a hallmark of a variety of real-world networks. Individual communities in networks form functional modules of complex systems described by networks. Therefore, finding communities in networks is essential to approaching and understanding complex systems described by networks. In fact, network science has made a great deal of effort to develop effective and efficient methods for detecting communities in networks. Here we put forward a type of community detection, which has been little examined so far but will be practically useful. Suppose that we are given a set of source nodes that includes some (but not all) of "true" members of a particular community; suppose also that the set includes some nodes that are not the members of this community (i.e., "false" members of the community). We propose to detect the community from this "imperfect" and "inaccurate" set of source nodes using attractor dynamics of recurrent neural networks. Community detection by the proposed method can be viewed as restoration of the original pattern from a deteriorated pattern, which is analogous to cue-triggered recall of short-term memory in the brain. We demonstrate the effectiveness of the proposed method using synthetic networks and real social networks for which correct communities are known.

  20. Response and Dynamical Stability of Oscillators with Discontinuous or Steep First Derivative of Restoring Characteristic

    Directory of Open Access Journals (Sweden)

    Željko Božić

    2009-01-01

    Full Text Available Response and dynamical stability of oscillators with discontinuous or steep first derivative of restoring characteristic is considered in this paper. For that purpose, a simple single-degree-of-freedom system with piecewise-linear force-displacement relationship subjected to a harmonic force excitation is analysed by the method of piecing the exact solutions (MPES in the time domain and by the incremental harmonic balance method (IHBM in the frequency domain. The stability of the periodic solutions obtained in the frequency domain by IHBM is estimated by the Floquet-Lyapunov theorem. Obtained frequency response characteristic is very complex and includes multi-frequency response for a single frequency excitation, jump phenomenon, multi-valued and non-periodic solutions. Determining of frequency response characteristic in the time domain by MPES is exceptionally time consuming, particularly inside the frequency ranges of co-existence of multiple stable solutions. In the frequency domain, IHBM is very efficient and very well suited for obtaining wide range frequency response characteristics, parametric studies and bifurcation analysis. On the other hand, neglecting of very small harmonic terms (which in-significantly influence the r.m.s. values of the response and are very small in comparison to other terms of the spectrum can cause very large error in evaluation of the eigenvalues of the monodromy matrix, and so they can lead to incorrect prediction of the dynamical stability of the solution. Moreover, frequency ranges are detected inside which the procedure of evaluation of eigenvalues of the monodromy matrix does not converge with increasing the number of harmonics included in the supposed approximate solution.

  1. [Dynamics of unprotected soil organic carbon with the restoration process of Pinus massoniana plantation in red soil erosion area].

    Science.gov (United States)

    Lü, Mao-Kui; Xie, Jin-Sheng; Zhou, Yan-Xiang; Zeng, Hong-Da; Jiang, Jun; Chen, Xi-Xiang; Xu, Chao; Chen, Tan; Fu, Lin-Chi

    2014-01-01

    By the method of spatiotemporal substitution and taking the bare land and secondary forest as the control, we measured light fraction and particulate organic carbon in the topsoil under the Pinus massoniana woodlands of different ages with similar management histories in a red soil erosion area, to determine their dynamics and evaluate the conversion processes from unprotected to protected organic carbon. The results showed that the content and storage of soil organic carbon increased significantly along with ages in the process of vegetation restoration (P soil organic carbon content and distribution proportion to the total soil organic carbon increased significantly (P soil organic carbon mostly accumulated in the form of unprotected soil organic carbon during the initial restoration period, and reached a stable level after long-term vegetation restoration. Positive correlations were found between restoration years and the rate constant for C transferring from the unprotected to the protected soil pool (k) in 0-10 cm and 10-20 cm soil layers, which demonstrated that the unprotected soil organic carbon gradually transferred to the protected soil organic carbon in the process of vegetation restoration.

  2. Region-confined restoration method for motion-blurred star image of the star sensor under dynamic conditions.

    Science.gov (United States)

    Ma, Liheng; Bernelli-Zazzera, Franco; Jiang, Guangwen; Wang, Xingshu; Huang, Zongsheng; Qin, Shiqiao

    2016-06-10

    Under dynamic conditions, the centroiding accuracy of the motion-blurred star image decreases and the number of identified stars reduces, which leads to the degradation of the attitude accuracy of the star sensor. To improve the attitude accuracy, a region-confined restoration method, which concentrates on the noise removal and signal to noise ratio (SNR) improvement of the motion-blurred star images, is proposed for the star sensor under dynamic conditions. A multi-seed-region growing technique with the kinematic recursive model for star image motion is given to find the star image regions and to remove the noise. Subsequently, a restoration strategy is employed in the extracted regions, taking the time consumption and SNR improvement into consideration simultaneously. Simulation results indicate that the region-confined restoration method is effective in removing noise and improving the centroiding accuracy. The identification rate and the average number of identified stars in the experiments verify the advantages of the region-confined restoration method.

  3. Dynamic in situ observation of voltage-driven repeatable magnetization reversal at room temperature

    Science.gov (United States)

    Gao, Ya; Hu, Jia-Mian; Nelson, C. T.; Yang, T. N.; Shen, Y.; Chen, L. Q.; Ramesh, R.; Nan, C. W.

    2016-03-01

    Purely voltage-driven, repeatable magnetization reversal provides a tantalizing potential for the development of spintronic devices with a minimum amount of power consumption. Substantial progress has been made in this subject especially on magnetic/ferroelectric heterostructures. Here, we report the in situ observation of such phenomenon in a NiFe thin film grown directly on a rhombohedral Pb(Mg1/3Nb2/3)0.7Ti0.3O3(PMN-PT) ferroelectric crystal. Under a cyclic voltage applied perpendicular to the PMN-PT without a magnetic field, the local magnetization of NiFe can be repetitively reversed through an out-of-plane excursion and then back into the plane. Using phase field simulations we interpret magnetization reversal as a synergistic effect of the metastable ferroelastic switching in the PMN-PT and an electrically rotatable local exchange bias field arising from the heterogeneously distributed NiO clusters at the interface.

  4. 电力系统恢复初期考虑动态特性的负荷恢复优化%Load Restoration Optimization Considering Dynamic Constraints During Initial Period of Power System Recovery

    Institute of Scientific and Technical Information of China (English)

    龚薇; 刘俊勇; 贺星棋; 胥威汀

    2014-01-01

    During the initial period of power system recovery, how to maximally restore the power supply in a weak power system was researched. Considering great changes of voltage and frequency during power system transient process after the service restoration, the physical nature during the initial period of power system recovery can be revealed better by using transient energy function of non-autonomous system to analyze the dynamic frequency and to calculate the ultimate capacity in each load that can be restored. The load impact energy and the dynamic frequency constraint are led in to guide the drafting of maximal load restoration programs, therefrom a method to draw up the load restoration scheme, in which the dynamic characteristics is taken into account, is put forward. Using this method a maximal load restoration scheme, which can meet the requirement on power system dynamic characteristics, could be drawn up, meanwhile it can be found that using load impact energy the impact of putting load into operation on power system can be reflected more accurately, thus it can offer helpful guidance to the drafting and evaluation of load restoration strategy.%电力系统恢复初期,对如何在薄弱小电网下最大限度地恢复负荷进行了研究。考虑到投入负荷后的系统过渡过程中各种状态量的巨大变化,从非自治系统暂态能量函数的角度分析其动态变化过程,能更好地揭示系统恢复初期的物理本质。引入负荷冲击能量和动态频率来指导制定最大限度的负荷恢复方案,由此提出考虑动态特性的负荷恢复方案制定方法。通过该方法能够制定出满足系统动态特性要求的最大限度负荷恢复方案,同时可以发现用负荷冲击能量能更准确地反映负荷投入对系统的影响,为负荷恢复策略制定及评估提供有益的指导。

  5. Voltage Quality Enhancement and Fault Current Limiting with Z-Source based Series Active Filter

    Directory of Open Access Journals (Sweden)

    F. Gharedaghi

    2011-11-01

    Full Text Available In this study, series active filter or dynamic voltage restorer application is proposed for reduction of downstream fault current in addition to voltage quality enhancement. Recently, the application of Z-source inverter is proposed in order to optimize DVR operation. This inverter makes DVR to operate appropriately when the energy storage device’s voltage level severely falls. Here, the Z-source inverter based DVR is proposed to compensate voltage disturbance at the PCC and to reduce the fault current in downstream of DVR. By calculating instantaneous current magnitude in synchronous frame, control system recognizes if the fault exists or not, and determines whether DVR should compensate voltage disturbance or try to reduce the fault current. The proposed system is simulated under voltage sag and swell and short circuit conditions. The simulation results show that the system operates correctly under voltage sag and short circuit conditions.

  6. Phase Angle Calculation Dynamics of Type 4 Wind Turbines in RMS Simulations during Severe Voltage Dips

    DEFF Research Database (Denmark)

    Altin, Müfit; Göksu, Ömer; Sørensen, Poul Ejnar;

    2016-01-01

    the simulation convergence without adding complexity to the generic models, a first order filtering approach is proposed as a phase angle calculation algorithm in the grid synchronization of the rms type 4 wind turbine models. The proposed approach provides robustness for the simulation of large scale power......In order to conduct power system simulations with high shares of wind energy, standard wind turbine models, which are aimed to be generic rms models for a wide range of wind turbine types, have been developed. As a common practice of rms simulations, the power electronic interface of wind turbines...... is assumed to be ideally synchronized, i.e. grid synchronization (e.g. PLL) is not included in simplified wind turbine models. As will be shown in this paper, this practice causes simulation convergence problems during severe voltage dips and when the loss of synchronism occurs. In order to provide...

  7. Dynamic voltage and frequency scaling for on-demand performance and availability of biomedical embedded systems.

    Science.gov (United States)

    Raskovic, Dejan; Giessel, David

    2009-11-01

    The goal of the study presented in this paper is to develop an embedded biomedical system capable of delivering maximum performance on demand, while maintaining the optimal energy efficiency whenever possible. Several hardware and software solutions are presented allowing the system to intelligently change the power supply voltage and frequency in runtime. The resulting system allows use of more energy-efficient components, operates most of the time in its most battery-efficient mode, and provides means to quickly change the operation mode while maintaining reliable performance. While all of these techniques extend battery life, the main benefit is on-demand availability of computational performance using a system that is not excessive. Biomedical applications, perhaps more than any other application, require battery operation, favor infrequent battery replacements, and can benefit from increased performance under certain conditions (e.g., when anomaly is detected) that makes them ideal candidates for this approach. In addition, if the system is a part of a body area network, it needs to be light, inexpensive, and adaptable enough to satisfy changing requirements of the other nodes in the network.

  8. Dynamic simulation and experimental study of inspection robot for high-voltage transmission-line

    Institute of Scientific and Technical Information of China (English)

    XIAO Xiao-hui; WU Gong-ping; DU E; SHI Tie-lin

    2005-01-01

    A mobile robot developed by Wuhan University for full-path hotline inspection on 220 kV transmission lines was presented. With 4 rotating joints and 2 translational ones, such robot is capable of traveling along non-obstacle straight-line segment and surmounting straight-line segment obstacles as well as transferring between two spans automatically. Lagrange's equations were utilized to derive dynamic equations of all the links, including items of inertia, coupling inertia, Coriolis acceleration, centripetal acceleration and gravity. And a dynamic response experiment on elemental motions of robot prototype's travelling along non-obstacle straight-line segment and surmounting obstacles was performed on 220 kV 1∶1 simulative overhanging transmission-line in laboratory. In addition, dynamic numerical simulation was conducted in the corresponding condition. Comparison and analysis on results of experiment and numerical simulation have validated theoretical model and simulation resolution. Therefore, the dynamic model formed hereunder can be used for the study of robot control.

  9. VOLTAGE COMPENSATION USING ARTIFICIAL NEURAL NETWORK

    African Journals Online (AJOL)

    VOLTAGE COMPENSATION USING ARTIFICIAL NEURAL NETWORK: A CASE STUDY OF RUMUOLA DISTRIBUTION NETWORK. ... The artificial neural networks controller engaged to controlling the dynamic voltage ... Article Metrics.

  10. Dynamics of bacterial communities in soils of rainforest fragments under restoration processes

    Science.gov (United States)

    Vasconcellos, Rafael; Zucchi, Tiago; Taketani, Rodrigo; Andreote, Fernando; Cardoso, Elke

    2014-05-01

    The Brazilian Atlantic Forest ("Mata Atlântica") has been largely studied due to its valuable and unique biodiversity. Unfortunately, this priceless ecosystem has been widely deforested and only 10% of its original area still remains. Many projects have been successfully implemented to restore its fauna and flora but there is a lack of information on how the soil bacterial communities respond to this process. Thus, our aim was to evaluate the influence of soil attributes and seasonality on soil bacterial communities of rainforest fragments under restoration processes. Soil samples from a native site and two ongoing restoration fragments with different ages of implementation (10 and 20 years) were collected and assayed by using culture-independent approaches. Our findings demonstrate that seasonality barely altered the bacterial distribution whereas soil chemical attributes and plant diversity highly influenced the bacterial community structure during the restoration process. Moreover, the strict relationship observed for two bacterial groups, Solibacteriaceae and Verrucomicrobia, one with the youngest (10 years) and the other with the oldest (native) site suggests their use as bioindicators of soil quality and soil recovery of forest fragments under restoration.

  11. An improved low-voltage ride-through performance of DFIG based wind plant using stator dynamic composite fault current limiter.

    Science.gov (United States)

    Gayen, P K; Chatterjee, D; Goswami, S K

    2016-05-01

    In this paper, an enhanced low-voltage ride-through (LVRT) performance of a grid connected doubly fed induction generator (DFIG) has been presented with the usage of stator dynamic composite fault current limiter (SDCFCL). This protection circuit comprises of a suitable series resistor-inductor combination and parallel bidirectional semiconductor switch. The SDCFCL facilitates double benefits such as reduction of rotor induced open circuit voltage due to increased value of stator total inductance and concurrent increase of rotor impedance. Both effects will limit rotor circuit over current and over voltage situation more secured way in comparison to the conventional scheme like the dynamic rotor current limiter (RCL) during any type of fault situation. The proposed concept is validated through the simulation study of the grid integrated 2.0MW DFIG.

  12. Control and Protection Cooperation Strategy for Voltage Instability

    DEFF Research Database (Denmark)

    Liu, Zhou; Chen, Zhe; Sun, Haishun;

    2012-01-01

    Most cascaded blackouts are caused by unexpected backup relay operations due to low voltage or overload state caused by post fault load restoration dynamics. If such state can be sensed and adjusted appropriately prior to those relay actions, system stability might be sustained. This paper proposed...... a control and protection cooperation strategy to prevent post fault voltage instability. The multi-agent technology is applied for the strategy implementation; the criteria based on wide area measured apparent impedances are defined to choose the control strategy, such as tap changer adjusting or load...

  13. Dynamic Characteristic Analysis of Linear DC Motor by 3D EMCN Considering Input Voltage

    Energy Technology Data Exchange (ETDEWEB)

    Ha, Kyung Ho; Yeom, Sang Bu [Changwon National University, Changwon(Korea); Hong, JUNG Pyo; Hur Jin; Kang Do Hyunc [Hanyang University(Seoul Campus), Seoul(Korea)

    2002-02-01

    In order to design the Linear DC Motor (LDM) With improved characteristics, transient and steady state analysis are required. Furthermore, 3D analysis is also needed to analyze the precise characteristics like thrust, time harmonics. This paper deals with the transient and dynamic characteristic analysis if LDM by coupling of external circuit and motion equation using 3D Equivalent Magnetic Circuit Network Method (EMCN). For the three dimensional analysis of electric machine, EMCN is very effective method that ensures high accuracy similar to FEM and short computation time. Also, The modeling by EMCN easily allows the mover to move with respect to the Sartre at each time Also, and the spatial moving step is determined by the solution of the mechanical motion equation and the computed electromagnetic thrust. The results are compared with experimental ones to clarify the usefulness and verify the accuracy of the proposed method. (author). 11 refs., 20 figs., 2 tabs.

  14. Late-Successional and Old-Growth Forests in the Northeastern United States: Structure, Dynamics, and Prospects for Restoration

    Directory of Open Access Journals (Sweden)

    Mark J. Ducey

    2013-11-01

    Full Text Available Restoration of old-growth forest structure is an emerging silvicultural goal, especially in those regions where old-growth abundance falls below the historic range of variability. However, longitudinal studies of old-growth dynamics that can inform silvicultural and policy options are few. We analyzed the change in structure, including stand density, diameter distribution, and the abundance of large live, standing dead, and downed dead trees on 58 late-successional and old-growth plots in Maine, USA, and compared these to regional data from the U.S. Forest Inventory and Analysis program. Structural dynamics on the late-successional plots reflected orderly change associated with density-dependent growth and mortality, but dynamics on the old-growth plots were more variable. Some plots experienced heavy mortality associated with beech bark disease. Diameter distributions conformed poorly to a classic exponential distribution, and did not converge toward such a distribution at the plot scale. Although large live trees showed a broad trend of increasing density in regional forests, recent harvesting patterns offset a considerable fraction of those gains, while mean diameter was static and the number of large dead trees was weakly declining. Even though forests of the northeast are aging, changes in silviculture and forest policy are necessary to accelerate restoration of old-growth structure.

  15. Landscape context affects use of restored grasslands by mammals in a dynamic agroecosystem

    National Research Council Canada - National Science Library

    Berry, Brian; Schooley, Robert L; Ward, Michael P

    2017-01-01

    ... agroecosystem in Illinois from 2014 to 2015. We tested hypotheses about the effects of local habitat conditions and landscape context on use of restored grasslands by four focal species: raccoons (Proryon lotor), eastern cottontails (Sylvilagus floridanus), coyotes (Canis latrans), and white-tailed deer (Odocoileus virginianus). Most species showed s...

  16. Low-Energy Real-Time OS Using Voltage Scheduling Algorithm for Variable Voltage Processors

    OpenAIRE

    Okuma, Takanori; Yasuura, Hiroto

    2001-01-01

    This paper presents a real-time OS based on $ mu $ITRON using proposed voltage scheduling algorithm for variable voltage processors which can vary supply voltage dynamically. The proposed voltage scheduling algorithms assign voltage level for each task dynamically in order to minimize energy consumption under timing constraints. Using the presented real-time OS, running tasks with low supply voltage leads to drastic energy reduction. In addition, the presented voltage scheduling algorithm is ...

  17. Investigation and Improvement of Transient Response of DVR at Medium Voltage Level

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Wei Li, Yun; Chaing Loh, Poh;

    2007-01-01

    An area of interest for dynamic voltage restorer (DVR) research is the damping of transient oscillations initiated at the start and at the recovery instant from a voltage sag. Nonlinear loads, with harmonic currents close to the DVR filter resonance frequency, can also excite the resonance...... oscillations. To compensate voltage sags and dampen high-frequency oscillations simultaneously, an investigation of the transient response of DVR is first carried out. Possible control schemes and their effects on the oscillation attenuation are also studied. Such studied control schemes include the commonly...... used single voltage loop control, voltage feedback plus reference feedforward control, and double-loop control with an outer voltage loop and an inner current loop. Subsequently, an effective and simple resonance damping method is proposed by employing a closed-loop control with an embedded two...

  18. Maintaining Restored Bone with Bisphoshonate in the Ovariectomized Rat Skeleton: Dynamic Histomorphometry of Changes in Bone Mass

    Science.gov (United States)

    Jee, W. S. S.; Tang, L.; Ke, H. Z.; Setterberg, R. B.; Kimmel, D. B.

    1993-01-01

    This experiment contains the crucial data for the Lose, Restore and Maintain (LRM) concept, a practical approach for reversing existing osteoporosis. The LRM concept uses ovariectomy (ox) to lose bone, an anabolic agent to restore bone mass and then switches to an anti-resorptive agent to maintain bone mass. We ox'd or sham-ox'd rats for 150 days (Loss Phase), treated them with 6 mg PGE2/kg/d for 75 days to restore lost cancellous bone mass (Restore Phase) and then stopped PGE2 treatment and began treatment with 1 or 5 micro-g/kg Risedronate, a bisphosphonate twice a week for 60 days (Maintain Phase). During the Loss Phase, cancellous bone volumes of the proximal tibial metaphysis (PTM) in the ox'd rat fell to 19% of initial controls. During the Restore Phase, the PTM bone volume in ox'd rats doubled. However, when PGE2 treatment was stopped, the PGE2-induced cancellous bone disappeared. In contrast, 5 micro-g of Risedronate inhibited the bone loss and maintained it at the PGE2 treatment level. The key dynamic histomorphometry value for the restore (R) and maintenance (M) phases was the ratio of bone formation to resorption rates. The ratio was elevated to 5.8 in the R phase and depressed to 0.4 for no and 1 micro-g Risedronate treated M phase and to a ratio of near unity of 1.1 for the 5 micro-g Risedronate treatment. These findings indicate that we were successful in maintaining the new PTM bone induced by PGE2 after discontinuing PGE2 by administering enough Risedronate, a resorption inhibitor. We concluded that the LRM concept is correct and such an approach should be considered when employing anabolic agents or growth factors in the treatment of osteoporosis. Continued use of an anabolic agent may not be appropriate because of cost, potential adverse side effects and a loss of efficacy.

  19. Maintaining Restored Bone with Bisphosphonate in the Ovariectomized Rat Skeleton: Dynamic Histomorphometry of Changes in Bone Mass

    Science.gov (United States)

    Jee, W. S. S.; Tang, L.; Ke, H. Z.; Setterberg, R. B.; Kimmel, D. B.

    1993-01-01

    This experiment contains the crucial data for the Lose, Restore and Maintain (LRM) concept, a practical approach for reversing existing osteoporosis. The LRM concept uses ovariectomy (ox) to lose bone, an anabolic agent to restore bone mass and then switches to an antiresorptive agent to maintain bone mass. We ox'd or sham-ox'd rats for 150 days (Loss Phase), treated them with 6 mg PGE(sub 2)kg/d for 75 days to restore lost cancellous bone mass (Restore Phase) and then stopped PGE(sub 2) treatment and began treatment with 1 or 5 micrograms/kg Risedronate, a bisphosphonate twice a week for 60 days (Maintain Phase). During the Loss Phase, cancellous bone volumes of the Proximal Tibial Metaphysis (PTM) in the ox'd rat fell to 19% of initial controls. During the Restore Phase, the PTM bone volume in ox'd rats doubled. However, when PGE(sub 2) treatment was stopped, the PGE(sub 2)-induced cancellous bone disappeared. In contrast, 5 miligrams of Risedronate inhibited the bone loss and maintained it at the PGE(sub 2) treatment level. The key dynamic histomorphometry value for the Restore (R) and Maintenance (M) phases was the ratio of bone formation to resorption rates. The ratio was elevated to 5.8 in the R phase and depressed to 0.4 for no and 1 miligram Risedronate treated M phase and to a ratio of near unity of 1.1 for the 5miligrams Risedronate treatment. These findings indicate that we were successful in maintaining the new PTM bone induced by PGE(sub 2) after discontinuing PGE(sub 2) by administering enough Risedronate, a resorption inhibitor. We concluded that the LRM concept is correct and such an approach should be considered when employing anabolic agents or growth factors in the treatment of osteoporosis. Continued use of an anabolic agent may not be appropriate because of cost, potential adverse side effects and a loss of efficacy.

  20. Using SVC to Improve Dynamic Voltage Stability of Regional Power Grid%用SVC提高区域电网的动态电压稳定性

    Institute of Scientific and Technical Information of China (English)

    唐莉

    2011-01-01

    The differences between power stability and frequency stability are analyzed. The necessity of regional maintains voltage stability is proposed. Under two conditions that reactive power compensator for the capacitors and SVC, the dynamic process of regional power grid voltage after large disturbances are simulated. The results show that using SVC can significantly improve the dynamic voltage stability of the regional power grid. The effects of SVC regulator time constant on dynamic process of voltage change are discussed.%分析电压稳定性与频率稳定性的不同,提出分区保持电压稳定性的必要性。仿真计算了无功补偿器为电容器和SVC两种情况下区域电网发生大干扰后电压变化的动态过程,说明采用SVC可以显著提高区域电网的动态电压稳定性,并探讨SVC调节的时间常数对电压变化的动态过程的影响。

  1. [Remote sensing based monitoring of vegetation dynamics and ecological restoration in Beijing mountainous area].

    Science.gov (United States)

    Hu, Yong; Liu, Liang-yun; Jia, Jian-hua

    2010-11-01

    By using the Landsat images in 1979, 1988, 1999, 2005, and 2009, and the linear unmixed model at pixel scale, this paper analyzed the spatiotemporal variation of vegetation coverage in Beijing mountainous area. After detecting the areas of vegetation degradation or restoration, the impacts of elevation, slope, and soil type on vegetation restoration were studied. From 1979 to 1988, the vegetation coverage in the study area had no obvious change, but in the following 12 years, the vegetation coverage was seriously destroyed due to the fast development of social economy. Fortunately, many protective measures were taken since 2000, which improved the vegetation coverage to 72% in 2009, with an increment of 13% compared to the vegetation coverage in 1999. A significant correlation was observed between the variations of vegetation coverage and territorial features. The areas with poor soil or large slope were more easily suffered from degradation than other places, and the flat regions with low elevation were more affected by human activities.

  2. Amphibian dynamics in constructed ponds on a wildlife refuge: developing expected responses to hydrological restoration

    Science.gov (United States)

    Hossack, Blake R.

    2017-01-01

    Management actions are based upon predictable responses. To form expected responses to restoration actions, I estimated habitat relationships and trends (2002–2015) for four pond-breeding amphibians on a wildlife refuge (Montana, USA) where changes to restore historical hydrology to the system greatly expanded (≥8 times) the flooded area of the primary breeding site for western toads (Anaxyrus boreas). Additional restoration actions are planned for the near future, including removing ponds that provide amphibian habitat. Multi-season occupancy models based on data from 15 ponds sampled during 7 years revealed that the number of breeding subpopulations increased modestly for Columbia spotted frogs (Rana luteiventris) and was stationary for long-toed salamanders (Ambystoma macrodactylum) and Pacific treefrogs (Pseudacris regilla). For these three species, pond depth was the characteristic that was associated most frequently with occupancy or changes in colonization and extinction. In contrast, a large decrease in colonization by western toads explained the decline from eight occupied ponds in 2002 to two ponds in 2015. This decline occurred despite an increase in wetland area and the colonization of a newly created pond. These changes highlight the challenges of managing for multiple species and how management responses can be unpredictable, possibly reducing the efficacy of targeted actions.

  3. Actin Dynamics Regulates Voltage-Dependent Calcium-Permeable Channels of the Vicia faba Guard Cell Plasma Membrane

    Institute of Scientific and Technical Information of China (English)

    Wei Zhang; Liu-Min Fan

    2009-01-01

    Free cytosolic Ca~(2+) ([Ca~(2+)]_(cyt)) is an ubiquitous second messenger in plant cell signaling, and [Ca~(2+)]_(cyt) elevation is associated with Ca~(2+)-permeable channels in the plasma membrane and endomembranes regulated by a wide range of stimuli. However, knowledge regarding Ca~(2+) channels and their regulation remains limited in planta. A type of voltage-dependent Ca~(2+)-permeable channel was identified and characterized for the Vicia faba L. guard cell plasma membrane by using patch-clamp techniques. These channels are permeable to both Ba~(2+) and Ca~(2+), and their activities can be inhibited by micromolar Gd~(3+). The unitary conductance and the reversal potential of the channels depend on the Ca~(2+) or Ba~(2+) gradients across the plasma membrane. The inward whole-cell Ca~(2+) (Ba~(2+)) current, as well as the unitary current amplitude and NP. of the single Ca~(2+) channel, increase along with the membrane hyperpolarization. Pharmacological experiments suggest that actin dynamics may serve as an upstream regulator of this type of calcium channel of the guard cell plasma membrane. Cytochalasin D, an actin polymerization blocker, activated the NP_o of these channels at the single channel level and increased the current amplitude at the whole-cell level. But these channel activations and current increments could be restrained by pretreatment with an F-actin stabilizer, phalloidin. The potential physiological significance of this regulatory mechanism is also discussed.

  4. Recombination dynamics as a key determinant of open circuit voltage in organic bulk heterojunction solar cells: a comparison of four different donor polymers

    Energy Technology Data Exchange (ETDEWEB)

    Maurano, Andrea; Hamilton, Rick; Shuttle, Chris G.; O' Regan, Brian; Zhang, Weimin; McCulloch, Iain; Durrant, James R. [Departments of Chemistry, Imperial College London, South Kensington SW7 2AZ (United Kingdom); Ballantyne, Amy M.; Nelson, Jenny [Departments of Physics, Imperial College London, South Kensington SW7 2AZ (United Kingdom); Azimi, Hamed [Konarka Austria, Altenbergerstrasse 69, A-4040 Linz (Austria); Christian Doppler Laboratory for Surface Optics, Johannes Kepler University, Linz (Austria); Morana, Mauro; Brabec, Christoph J. [Konarka Austria, Altenbergerstrasse 69, A-4040 Linz (Austria)

    2010-11-24

    Transient photovoltage and charge extraction analyses are employed to analyzes charge carrier densities and bimolecular recombination dynamics in organic polymer: fullerene solar cells under open circuit operating conditions, employing four different donor polymers. An equation is derived which allows us to calculate the device V{sub OC} from these kinetic measurements. This equation allows us to calculate voltage output of devices within {+-} 25 meV of directly measured values. This analysis thus allows us to relate device open circuit voltage directly to the kinetics of bimolecular recombination, and thereby the influence of nanomorphology upon device voltage output. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. [Nutrient dynamics in forest plantations of Azadirachta indica (Meliaceae) established for restoration of degraded lands in Colombia].

    Science.gov (United States)

    Flórez-Flórez, Claudia Patricia; León-Peláez, Juan Diego; Osorio-Vega, Nelson Walter; Restrepo-Llano, Manuel Fernando

    2013-06-01

    Nutrient dynamics in forest plantations of Azadirachta indica (Meliaceae) established for restoration of degraded lands in Colombia. Azadirachta indica is a tree species which use is steadily increasing for restoration of tropical and subtropical arid and degraded lands throughout the world. The objective of this research study was to evaluate the potential of these plantations as an active restoration model for the recovery of soils under desertification in arid lands of Colombia. Litter traps and litter-bags were installed in twenty 250m2 plots. Green leaves and soil samples inside and outside this species plantations were taken, and their elemental concentrations were determined. Litterfall, leaf litter decomposition and foliar nutrient resorption were monitored for one year. The annual contributions of organic material, such as fine litterfall, represented 557.54kg/ha, a third of which was A. indica leaves. The greatest potential returns of nutrients per foliar litterfall were from Ca (4.6kg/ha) and N (2.4kg/ha), and the smallest potential returns came from P (0.06kg/ha). A total of 68% of the foliar material deposited in litter-bags disappeared after one year. The greatest release of nutrients was that of K (100%), and the least was that of N (40%). P was the most limiting nutrient, with low edaphic availability and high nutrient use efficiency from Vitousek's index (IEV = 3176) and foliar nutrient resorption (35%). Despite these plantations are young, and that they have not had forestry management practices, as an active restoration model, they have revitalized the biogeochemical cycle, positively modifying the edaphic parameters according to the increases in organic material, P and K of 72%, 31% and 61%, respectively. Furthermore, they improved the stability of aggregates and the microbe respiration rates. The forest plantation model with exotic species has been opposed by different sectors; however, it has been acknowledged that these projects derive many

  6. 适用于动态电压恢复器电压检测的滤波算法%Filtering Method for Dynamic Voltage Regulator

    Institute of Scientific and Technical Information of China (English)

    张强; 周晖; 齐智平

    2009-01-01

    动态电压恢复器(DVR)是目前治理电网动态电压问题中有效的手段之一,为了能够准确地监测电网电压的变化,数字滤波是DVR检测单元中必不可少的一个环节.采用幅值突变鉴别的电压增量惯性滤波法,既可以克服以往惯性滤波中时滞过大的缺点,又可以保证滤波后的电压波形在电压突变处的真实性,完全可以满足动态电压恢复器对检测单元滤波的需求.%Dynamic voltage regulator (DVR) is an efficacious measure to solve power quality problems. It is indispensable for DVR to adopt digital filter in its control system to detect voltage sags and swells accurately. Voltage increment inertial filter that can distinguish the sudden changes of voltage amplitude, can conquer the time delay problem of the conventional inertial filter, and ensure the creditability of filtered voltage waveform at the point of amplitude sudden change. So this filter method can meet the need of the test system of DVR perfectly.

  7. 基于Markov模型的动态电压调节策略%Dynamic voltage scaling policy based on Markov model

    Institute of Scientific and Technical Information of China (English)

    卜爱国

    2011-01-01

    基于Markov模型,针对具有离散工作电压模式的处理器提出了一种动态电压调节策略MKBVSP( Markov based voltage scaling policy).MKBVSP能够根据工作负载的需求变化实现处理器工作模式的动态切换,达到系统性能与能耗之间的平衡.实验结果表明,MKBVSP策略能够在更大程度上降低系统平均能耗,最大比率可达58%.%Based on Markov model, this paper presented a voltage scaling policy called Markov based voltage scaling policy for processor with discrete voltage levels. The supply voltage of process could be switched dynamically by MKBVSP according the variance of system workload, and the balance of system between the performance and the power could be obtained thereby. Experimental results demonstrate that the power consumption can be further reduced with the implementation of MKBVSP, which can be far decreased by 58%.

  8. Dynamical Restoration of Z_N Symmetry in SU(N)+Higgs Theories

    CERN Document Server

    Biswal, Minati; Saumia, P S

    2015-01-01

    We study the Z_N symmetry in SU(N)+Higgs theories with the Higgs field in the fundamental representation. The distributions of the Polyakov loop show that the Z_N symmetry is explicitly broken in the Higgs phase. On the other hand, inside the Higgs symmetric phase the Polyakov loop distributions and other physical observables exhibit the Z_N symmetry. This effective restoration of the Z_N symmetry changes the nature of the confinement-deconfinenement transition. We argue that the Z_N symmetry will lead to time independent topological defect solutions in the Higgs symmetric deconfined phase which will play important role at high temperatures.

  9. 电力系统恢复过程中的工频过电压动态优化控制%Dynamic Optimal Control of Sustained Overvoltage During Power System Restoration

    Institute of Scientific and Technical Information of China (English)

    陈彬; 王洪涛

    2015-01-01

    A rational sustained overvoltage control strategy is an important part of the power system restoration plan.In order to overcome the limitations of the sustained overvoltage static control strategy,a dynamic multi-objective sustained overvoltage control model is proposed. With the restoration sequence as the optimization period, and restoration operation as the segmentation flag,the model proposed takes the whole process into consideration.According to the demand for restoration, the objective functions adapted to restoration are defined and the risk of restoration sequence,operation time of voltage control scheme and voltage deviation of energized buses are considered.An improved strength Pareto evolutionary algorithm(SPEA2) is used to get the Pareto frontier,and the lexicographic ordering method is used to get the optimal solution.The effectiveness of the proposed model is verified by comparing and analyzing the simulation results of dynamic and static optimization in different restoration scenarios in Shandong power grid.%合理的持续工频过电压控制策略是电力系统恢复方案的重要组成部分。针对当前持续工频过电压控制静态优化方法的局限性,以恢复序列为优化周期,以线路投运为分段标志,建立了电力系统恢复过程中的动态多目标工频过电压优化控制模型,实现一个恢复周期内的全过程优化。根据恢复过程需要,结合系统恢复方案,定义了恢复过程中的工频过电压优化控制的目标函数,综合考虑恢复序列的操作风险、电压控制方案的操作时间以及系统的电压偏差对电压控制方案的影响。利用改进的强度 Pareto 进化算法(SPEA2)求解模型的 Pareto 最优解,并采用字典序法选择出适应不同恢复场景的最优方案。以山东电网为例,分析和比较了不同恢复场景下动态优化和静态优化的仿真结果,表明所述模型能够适应电力系统恢复的要求。

  10. Dynamic effects of restoring footpoint symmetry on closed magnetic field lines

    CERN Document Server

    Reistad, J P; Tenfjord, P; Laundal, K M; Snekvik, K; Haaland, S; Milan, S E; Oksavik, K; Frey, H U; Grocott, A

    2016-01-01

    Here we present an event where simultaneous global imaging of the aurora from both hemispheres reveals a large longitudinal shift of the nightside aurora of about 3 h, being the largest relative shift reported on from conjugate auroral imaging. This is interpreted as evidence of closed field lines having very asymmetric footpoints associated with the persistent positive $\\textit{y}$ component of the interplanetary magnetic field before and during the event. At the same time, the Super Dual Auroral Radar Network observes the ionospheric nightside convection throat region in both hemispheres. The radar data indicate faster convection toward the dayside in the dusk cell in the Southern Hemisphere compared to its conjugate region. We interpret this as a signature of a process acting to restore symmetry of the displaced closed magnetic field lines resulting in flux tubes moving faster along the banana cell than the conjugate orange cell. The event is analyzed with emphasis on Birkeland currents (BC) associated wit...

  11. Voltage and Pressure Scaling of Streamer Dynamics in a Helium Plasma Jet With N2 CO-Flow (Postprint)

    Science.gov (United States)

    2014-08-14

    increased applied voltage. These observed differences in the 2-D scaling properties of ionization wave sustained cathode directed streamer propagation in...streamer propagation in helium versus air16,17 are responsible for the observed differences in the propagation of ionization wave sustained streamer...increase quadratically with increased applied voltage. These observed differences in the 2-D scaling properties of ionization wave sustained cathode

  12. 输电网架恢复的动态优化决策方法%A Dynamic Optimization Decision-making Method for Power System Skeleton Restoration

    Institute of Scientific and Technical Information of China (English)

    王春义; 刘玉田

    2011-01-01

    Owing to the rather weak anti-disturbance capability, frequent equipment operation, increasing uncertain events and difficulty in ensuring the implementation of restoration process according to the pre-developed restoration plan during skeleton restoration, a dynamic optimization decision-making method for power system skeleton restoration is proposed. It employs the three-stage skeleton restoration strategy and the shortest path searching method to generate candidate schemes for each restoration step. The main factors influencing the power system security or restoration speed are chosen as attributes of candidate schemes and a multi-attribute decision-making method is adopted to make the optimal decision. Simulation results of a power system demonstrate that the method can coordinate system security with restoration speed and dynamically make skeleton restoration decision in accordance with the power system restoration process while providing effective supplement to the pre-developed restoration plan.%针对输电网架恢复过程中系统的抗扰动能力较弱、设备操作频繁、不确定性事件增多、恢复过程难以保证按预案进行的问题,提出了一种输电网架恢复的动态优化决策方法.该方法由三段式的输电网架恢复策略,根据系统恢复进程动态给定每一恢复步骤的候选恢复目标,综合考虑已恢复的系统节点,利用Dijkastra算法动态生成各目标的候选恢复方案,将影响系统安全和恢复速度的因素作为候选方案的属性,采用群体多属性决策方法给出优化决策.实例仿真结果表明,该方法能够协调系统安全与恢复速度,并能根据系统状态动态确定恢复目标及其恢复方案,提高了决策的可行性和灵活性,可为离线预案提供有效补充.

  13. Dynamic positron emission tomography image restoration via a kinetics-induced bilateral filter.

    Directory of Open Access Journals (Sweden)

    Zhaoying Bian

    Full Text Available Dynamic positron emission tomography (PET imaging is a powerful tool that provides useful quantitative information on physiological and biochemical processes. However, low signal-to-noise ratio in short dynamic frames makes accurate kinetic parameter estimation from noisy voxel-wise time activity curves (TAC a challenging task. To address this problem, several spatial filters have been investigated to reduce the noise of each frame with noticeable gains. These filters include the Gaussian filter, bilateral filter, and wavelet-based filter. These filters usually consider only the local properties of each frame without exploring potential kinetic information from entire frames. Thus, in this work, to improve PET parametric imaging accuracy, we present a kinetics-induced bilateral filter (KIBF to reduce the noise of dynamic image frames by incorporating the similarity between the voxel-wise TACs using the framework of bilateral filter. The aim of the proposed KIBF algorithm is to reduce the noise in homogeneous areas while preserving the distinct kinetics of regions of interest. Experimental results on digital brain phantom and in vivo rat study with typical (18F-FDG kinetics have shown that the present KIBF algorithm can achieve notable gains over other existing algorithms in terms of quantitative accuracy measures and visual inspection.

  14. Enhanced Dynamic Voltage Stability Support by VSC-HVDC for Offshore Wind Applications using Trajectory Sensitivity Analysis

    DEFF Research Database (Denmark)

    Liu, Hongzhi; Chen, Zhe; Liu, Leo

    2013-01-01

    . In this paper, VSC-HVDC transmission system is used to integrate a large-scale wind power plant into the onshore power grid. For different voltage support strategies of VSC-HVDC, a trajectory sensitivity analysisbased approach is proposed to find the minimum onshore VSC capacity with which the VSC-HVDC can...

  15. Low voltage logic circuits exploiting gate level dynamic body biasing in 28 nm UTBB FD-SOI

    Science.gov (United States)

    Taco, Ramiro; Levi, Itamar; Lanuzza, Marco; Fish, Alexander

    2016-03-01

    In this paper, the recently proposed gate level body bias (GLBB) technique is evaluated for low voltage logic design in state-of-the-art 28 nm ultra-thin body and box (UTBB) fully-depleted silicon-on-insulator (FD-SOI) technology. The inherent benefits of the low-granularity body-bias control, provided by the GLBB approach, are emphasized by the efficiency of forward body bias (FBB) in the FD-SOI technology. In addition, the possibility to integrate PMOS and NMOS devices into a single common well configuration allows significant area reduction, as compared to an equivalent triple well implementation. Some arithmetic circuits were designed using GLBB approach and compared to their conventional CMOS and DTMOS counterparts under different running conditions at low voltage regime. Simulation results shows that, for 300 mV of supply voltage, a 4 × 4-bit GLBB Baugh Wooley multiplier allows performance improvement of about 30% and area reduction of about 35%, while maintaining low energy consumption as compared to the conventional CMOS ⧹ DTMOS solutions. Performance and energy benefits are maintained over a wide range of process-voltage-temperature (PVT) variations.

  16. Dynamic pattern formation of liquid crystals using binary self-assembled monolayers on an ITO surface under DC voltage.

    Science.gov (United States)

    Ishida, Takao; Oyama, Makiko; Terada, Kei-ichi; Haga, Masa-aki

    2014-12-07

    There have been numerous studies of liquid crystal (LC) convection using sandwich-type LC cells under AC voltage. In contrast to previous LC convection studies under AC voltage, we propose the use of a binary self-assembled monolayer (SAM) with a redox-active Ru complex and insulating octadecyl phosphonic acid (C18) molecules on an indium tin oxide (ITO) surface as the electrode of sandwich-type LC cells under DC bias voltage. This is because the functionalized molecules immobilized on the ITO surface are expected to control the LC orientation and electrical conduction of LC cells, under an exact DC bias voltage. We successfully achieved LC pattern formation using ITO electrodes with binary SAMs in LC cells. Moreover, we confirmed that the LC pattern size was increased by increasing the coverage of the Ru complex in binary SAMs. We consider that a combination of three factors, electrical conduction change, controlling of LC orientation in the initial stage and redox-activity of the Ru-complex, is the reason for LC convection although we cannot fully explain the distribution of these three factors. We believe that our LC pattern formation is promising for new type devices e.g., artificial compound eyes using the LC device technology.

  17. VLSI implementation of a nonlinear neuronal model: a "neural prosthesis" to restore hippocampal trisynaptic dynamics.

    Science.gov (United States)

    Hsiao, Min-Chi; Chan, Chiu-Hsien; Srinivasan, Vijay; Ahuja, Ashish; Erinjippurath, Gopal; Zanos, Theodoros P; Gholmieh, Ghassan; Song, Dong; Wills, Jack D; LaCoss, Jeff; Courellis, Spiros; Tanguay, Armand R; Granacki, John J; Marmarelis, Vasilis Z; Berger, Theodore W

    2006-01-01

    We are developing a biomimetic electronic neural prosthesis to replace regions of the hippocampal brain area that have been damaged by disease or insult. We have used the hippocampal slice preparation as the first step in developing such a prosthesis. The major intrinsic circuitry of the hippocampus consists of an excitatory cascade involving the dentate gyrus (DG), CA3, and CA1 subregions; this trisynaptic circuit can be maintained in a transverse slice preparation. Our demonstration of a neural prosthesis for the hippocampal slice involves: (i) surgically removing CA3 function from the trisynaptic circuit by transecting CA3 axons, (ii) replacing biological CA3 function with a hardware VLSI (very large scale integration) model of the nonlinear dynamics of CA3, and (iii) through a specially designed multi-site electrode array, transmitting DG output to the hardware device, and routing the hardware device output to the synaptic inputs of the CA1 subregion, thus by-passing the damaged CA3. Field EPSPs were recorded from the CA1 dendritic zone in intact slices and "hybrid" DG-VLSI-CA1 slices. Results show excellent agreement between data from intact slices and transected slices with the hardware-substituted CA3: propagation of temporal patterns of activity from DG-->VLSI-->CA1 reproduces that observed experimentally in the biological DG-->CA3-->CA1 circuit.

  18. Effects of salinity on dynamics of soil carbon in degraded coastal wetlands: Implications on wetland restoration

    Science.gov (United States)

    Zhao, Qingqing; Bai, Junhong; Lu, Qiongqiong; Zhang, Guangliang

    2017-02-01

    To investigate the effects of salinity on dynamics of soil carbon contents and stocks, soil samples were collected at a depth of 30 cm at four sampling sites (Sites B, T, S and P) along a salinity gradient in a drained coastal wetland, the Yellow River Delta, China. The salinity of these four sites ranked in the order: B (8.68 ± 4.25 ms/cm) > T (5.89 ± 3.17 ms/cm) > S (3.19 ± 1.01 ms/cm) > P (2.26 ± 0.39 ms/cm). Soil total carbon (TC), soil organic carbon (SOC), and soil microbial biomass carbon (MBC) were measured. Based on these data, soil organic carbon density (SOCD) and soil microbial biomass carbon density (MBCD) were calculated at four sites. The results showed that the mean concentrations of TC and MBC showed a general deceasing tendency with increasing salinities in the top 30 cm of soils. The values of SOCD and MBCD exhibited similar tendency along the salinity gradient. As for profile distribution pattern, The C/N ratios ranged from 8.28 to 56.51. The microbial quotient values at four sampling sites were quite low, ranging from 0.06 to 0.19. Higher C/N ratios were found in samples with high salinity. Correlation analysis showed that the concentrations of TC and MBC at four sampling sites were significantly negatively correlated with salinity (P carbon accumulation and microbial activities.

  19. Effects of Restoration Techniques on Soil Carbon and Nitrogen Dynamics in Florida Longleaf Pine (Pinus palustris) Sandhill Forests

    OpenAIRE

    Martin Lavoie; Mack, Michelle C; John K. Hiers; Scott Pokswinski; Analie Barnett; Louis Provencher

    2014-01-01

    Historic fire suppression and intensive forest management in longleaf pine (Pinus palustris) sandhill forests has resulted in hardwood encroachment and degradation of this fire-dependent ecosystem. Active management is now required to restore native community structure and composition, but little is known about the long-term impacts of typical restoration techniques on ecosystem properties. In 1994, the Longleaf Pine Restoration Project (LPRP) was established in fire-excluded longleaf pine sa...

  20. Assessing Vegetation Cover Dynamics Induced by Policy-Driven Ecological Restoration and Implication to Soil Erosion in Southern China.

    Science.gov (United States)

    Zhang, Jien; Wang, Tianming; Ge, Jianping

    2015-01-01

    In the aftermath of the severe droughts and floods at the end of the 20th century, the Chinese government launched several ecological restoration projects, including the Natural Forest Protection Program in 1998 and the Grain-for-Green Program in 1999, to promote afforestation and reforestation to reduce surface runoff and consequent soil erosion nationwide. However, it is still unclear how vegetation has changed in southern China since the launch of these programs. In this study, we used the MODIS Enhanced Vegetation Index (EVI) to analyze the vegetation cover dynamics in southern China from 2000 to 2009 and evaluate the resulting effects of controlling soil erosion. Our observations indicate that 5.3% of the study area significantly increased and 0.98% significantly decreased in EVI value (p soil erosion based upon monitoring sediment yields at hydrologic stations in the Yangtze River. This study displays the spatial patterns of trend in vegetation growth since the beginning of the 21st century in southern China and highlights the important role of China's afforestation program.

  1. Dietary supplementation with omega-3 polyunsaturated fatty acids robustly promotes neurovascular restorative dynamics and improves neurological functions after stroke.

    Science.gov (United States)

    Zhang, Wenting; Wang, Hailian; Zhang, Hui; Leak, Rehana K; Shi, Yejie; Hu, Xiaoming; Gao, Yanqin; Chen, Jun

    2015-10-01

    Stroke is a devastating neurological disease with no satisfactory therapies to preserve long-term neurological function, perhaps due to the sole emphasis on neuronal survival in most preclinical studies. Recent studies have revealed the importance of protecting multiple cell types in the injured brain, such as oligodendrocytes and components of the neurovascular unit, before long-lasting recovery of function can be achieved. For example, revascularization in the ischemic penumbra is critical to provide various neurotrophic factors that enhance the survival and activity of neurons and other progenitor cells, such as oligodendrocyte precursor cells. In the present study, we hypothesized that chronic dietary supplementation with fish oil promotes post-stroke angiogenesis, neurogenesis, and oligodendrogenesis, thereby leading to long-term functional improvements. Mice received dietary supplementation with n-3 PUFA-enriched fish oil for three months before and up to one month after stroke. As expected, dietary n-3 PUFAs significantly increased levels of n-3 PUFAs in the brain and improved long-term behavioral outcomes after cerebral ischemia. n-3 PUFAs also robustly improved revascularization and angiogenesis and boosted the survival of NeuN/BrdU labeled newborn neurons up to 35days after stroke injury. Furthermore, these pro-neurogenic effects were accompanied by robust oligodendrogenesis. Thus, this is the first study to demonstrate that chronic dietary intake of n-3 PUFAs is an effective prophylactic measure not only to protect against ischemic injury for the long term but also to actively promote neurovascular restorative dynamics and brain repair.

  2. Governance and management dynamics of landscape restoration at multiple scales: Learning from successful environmental managers in Sweden.

    Science.gov (United States)

    Dawson, Lucas; Elbakidze, Marine; Angelstam, Per; Gordon, Johanna

    2017-03-14

    Due to a long history of intensive land and water use, habitat networks for biodiversity conservation are generally degraded in Sweden. Landscape restoration (LR) is an important strategy for achieving representative and functional green infrastructures. However, outcomes of LR efforts are poorly studied, particularly the dynamics of LR governance and management. We apply systems thinking methods to a series of LR case studies to analyse the causal structures underlying LR governance and management in Sweden. We show that these structures appear to comprise of an interlinked system of at least three sets of drivers and four core processes. This system exhibits many characteristics of a transformative change towards an integrated, adaptive approach to governance and management. Key challenges for Swedish LR projects relate to institutional and regulatory flexibility, the timely availability of sufficient funds, and the management of learning and knowledge production processes. In response, successful project leaders develop several key strategies to manage complexity and risk, and enhance perceptions of the attractiveness of LR projects.

  3. 基于动态响应的电压稳定分析方法%Analysis Method of Voltage Stability based on Dynamic Response

    Institute of Scientific and Technical Information of China (English)

    王亚俊; 吴佳军; 云雷; 王乙斐; 马志昊; 邵雅宁

    2013-01-01

    As modern power system is pushed to the maximum operation condition, system voltage stability becomes a significant issue. It is necessary to find out a precise and reliable method to analyze voltage stability. This paper presents a method which is based on the dynamic response theory. This method can analyze stability accurately by calculating Thevenin equivalent parameters and judging the status of voltage stability. The outcomes of IEEE 9-bus power system simulation have confirmed the validity and effectiveness of the method. Under the trend of on-line analysis, this method is of certain significance to on line analysis of voltage stability.%随着电力系统的运行越来越接近其极限状态,电力系统电压稳定问题日益突出,研究一种精确可靠的电压稳定分析方法是非常必要的.提出了一种基于动态响应的电压稳定分析方法,该方法通过计算戴维南等值参数及确定电压稳定判据可以精确实现电压稳定分析.IEEE 9节点算例仿真验证了该方法的正确性和有效性.当在线分析成为趋势的时候,该方法对实现电压稳定的在线分析有一定的现实意义.

  4. Structural refinement of the hERG1 pore and voltage-sensing domains with ROSETTA-membrane and molecular dynamics simulations.

    Science.gov (United States)

    Subbotina, Julia; Yarov-Yarovoy, Vladimir; Lees-Miller, James; Durdagi, Serdar; Guo, Jiqing; Duff, Henry J; Noskov, Sergei Yu

    2010-11-01

    The hERG1 gene (Kv11.1) encodes a voltage-gated potassium channel. Mutations in this gene lead to one form of the Long QT Syndrome (LQTS) in humans. Promiscuous binding of drugs to hERG1 is known to alter the structure/function of the channel leading to an acquired form of the LQTS. Expectably, creation and validation of reliable 3D model of the channel have been a key target in molecular cardiology and pharmacology for the last decade. Although many models were built, they all were limited to pore domain. In this work, a full model of the hERG1 channel is developed which includes all transmembrane segments. We tested a template-driven de-novo design with ROSETTA-membrane modeling using side-chain placements optimized by subsequent molecular dynamics (MD) simulations. Although backbone templates for the homology modeled parts of the pore and voltage sensors were based on the available structures of KvAP, Kv1.2 and Kv1.2-Kv2.1 chimera channels, the missing parts are modeled de-novo. The impact of several alignments on the structure of the S4 helix in the voltage-sensing domain was also tested. Herein, final models are evaluated for consistency to the reported structural elements discovered mainly on the basis of mutagenesis and electrophysiology. These structural elements include salt bridges and close contacts in the voltage-sensor domain; and the topology of the extracellular S5-pore linker compared with that established by toxin foot-printing and nuclear magnetic resonance studies. Implications of the refined hERG1 model to binding of blockers and channels activators (potent new ligands for channel activations) are discussed.

  5. Incorporating H2 Dynamics and Inhibition into a Microbially Based Methanogenesis Model for Restored Wetland Sediments

    Science.gov (United States)

    Pal, David; Jaffe, Peter

    2015-04-01

    Estimates of global CH4 emissions from wetlands indicate that wetlands are the largest natural source of CH4 to the atmosphere. In this paper, we propose that there is a missing component to these models that should be addressed. CH4 is produced in wetland sediments from the microbial degradation of organic carbon through multiple fermentation steps and methanogenesis pathways. There are multiple sources of carbon for methananogenesis; in vegetated wetland sediments, microbial communities consume root exudates as a major source of organic carbon. In many methane models propionate is used as a model carbon molecule. This simple sugar is fermented into acetate and H2, acetate is transformed to methane and CO2, while the H2 and CO2 are used to form an additional CH4 molecule. The hydrogenotrophic pathway involves the equilibrium of two dissolved gases, CH4 and H2. In an effort to limit CH4 emissions from wetlands, there has been growing interest in finding ways to limit plant transport of soil gases through root systems. Changing planted species, or genetically modifying new species of plants may control this transport of soil gases. While this may decrease the direct emissions of methane, there is little understanding about how H2 dynamics may feedback into overall methane production. The results of an incubation study were combined with a new model of propionate degradation for methanogenesis that also examines other natural parameters (i.e. gas transport through plants). This presentation examines how we would expect this model to behave in a natural field setting with changing sulfate and carbon loading schemes. These changes can be controlled through new plant species and other management practices. Next, we compare the behavior of two variations of this model, with or without the incorporation of H2 interactions, with changing sulfate, carbon loading and root volatilization. Results show that while the models behave similarly there may be a discrepancy of nearly

  6. Low-voltage gyrotrons

    Science.gov (United States)

    Glyavin, M. Yu.; Zavolskiy, N. A.; Sedov, A. S.; Nusinovich, G. S.

    2013-03-01

    For a long time, the gyrotrons were primarily developed for electron cyclotron heating and current drive of plasmas in controlled fusion reactors where a multi-megawatt, quasi-continuous millimeter-wave power is required. In addition to this important application, there are other applications (and their number increases with time) which do not require a very high power level, but such issues as the ability to operate at low voltages and have compact devices are very important. For example, gyrotrons are of interest for a dynamic nuclear polarization, which improves the sensitivity of the nuclear magnetic resonance spectroscopy. In this paper, some issues important for operation of gyrotrons driven by low-voltage electron beams are analyzed. An emphasis is made on the efficiency of low-voltage gyrotron operation at the fundamental and higher cyclotron harmonics. These efficiencies calculated with the account for ohmic losses were, first, determined in the framework of the generalized gyrotron theory based on the cold-cavity approximation. Then, more accurate, self-consistent calculations for the fundamental and second harmonic low-voltage sub-THz gyrotron designs were carried out. Results of these calculations are presented and discussed. It is shown that operation of the fundamental and second harmonic gyrotrons with noticeable efficiencies is possible even at voltages as low as 5-10 kV. Even the third harmonic gyrotrons can operate at voltages about 15 kV, albeit with rather low efficiency (1%-2% in the submillimeter wavelength region).

  7. Driving Forces of Dynamic Changes in Soil Erosion in the Dahei Mountain Ecological Restoration Area of Northern China Based on GIS and RS.

    Science.gov (United States)

    Li, Xiao; Niu, Xiang; Wang, Bing; Gao, Peng; Liu, Yu

    2016-01-01

    Dynamic change in soil erosion is an important focus of regional ecological restoration research. Here, the dynamic changes of soil erosion and its driving forces in the Dahei Mountain ecological restoration area of northern China were analyzed by LANDSAT TM remote sensing captured via geographic information system (GIS) technologies during three typical periods in 2004, 2008 and 2013. The results showed the following: (1) a decrease in intensive erosion and moderate erosion areas, as well as an increase in light erosion areas, was observed during two periods: one from 2004 to 2008 and the other from 2008 to 2013. (2) Between 2004 and 2008, the variation in the range of slight erosion was the largest (24.28%), followed by light erosion and intensive erosion; between 2008 and 2013, the variation in the range of intensive erosion area was the largest (9.89%), followed by slight erosion and moderate erosion. (3) Socioeconomic impact, accompanied by natural environmental factors, was the main driving force underlying the change in soil erosion within the ecological restoration area. In particular, the socioeconomic factors of per capita forest area and land reclamation rate, as well as the natural environmental factor of terrain slope, significantly influenced soil erosion changes within the ecological restoration area.

  8. Linking restoration ecology with coastal dune restoration

    Science.gov (United States)

    Lithgow, D.; Martínez, M. L.; Gallego-Fernández, J. B.; Hesp, P. A.; Flores, P.; Gachuz, S.; Rodríguez-Revelo, N.; Jiménez-Orocio, O.; Mendoza-González, G.; Álvarez-Molina, L. L.

    2013-10-01

    Restoration and preservation of coastal dunes is urgently needed because of the increasingly rapid loss and degradation of these ecosystems because of many human activities. These activities alter natural processes and coastal dynamics, eliminate topographic variability, fragment, degrade or eliminate habitats, reduce diversity and threaten endemic species. The actions of coastal dune restoration that are already taking place span contrasting activities that range from revegetating and stabilizing the mobile substrate, to removing plant cover and increasing substrate mobility. Our goal was to review how the relative progress of the actions of coastal dune restoration has been assessed, according to the ecosystem attributes outlined by the Society of Ecological Restoration: namely, integrity, health and sustainability and that are derived from the ecological theory of succession. We reviewed the peer reviewed literature published since 1988 that is listed in the ISI Web of Science journals as well as additional references, such as key books. We exclusively focused on large coastal dune systems (such as transgressive and parabolic dunefields) located on natural or seminatural coasts. We found 150 articles that included "coastal dune", "restoration" and "revegetation" in areas such as title, keywords and abstract. From these, 67 dealt specifically with coastal dune restoration. Most of the studies were performed in the USA, The Netherlands and South Africa, during the last two decades. Restoration success has been assessed directly and indirectly by measuring one or a few ecosystem variables. Some ecosystem attributes have been monitored more frequently (ecosystem integrity) than others (ecosystem health and sustainability). Finally, it is important to consider that ecological succession is a desirable approach in restoration actions. Natural dynamics and disturbances should be considered as part of the restored system, to improve ecosystem integrity, health and

  9. Spatial and temporal variations of dissolved organic matter dynamics in a disturbed Sphagnum peatland after hydrological restoration

    Science.gov (United States)

    Le Moing, Franck; Guirimand-Dufour, Audrey; Jozja, Nevila; Defarge, Christian; D'Angelo, Benoît; Binet, Stéphane; Gogo, Sébastien; Laggoun, Fatima

    2015-04-01

    Peatlands contain a third of the world soil C in spite of their relatively low global area (3% of land area). They can become sources of C because of human disturbances such as drainage. The aim of this work is to assess the effect of an hydrological restoration on a disturbed Sphagnum peatland. It concerns spatial and temporal variations of dissolved organic matter (DOM) dynamics. The investigated site was La Guette peatland (France, N 47°19'44', E 2°17'04', alt. 154m), whose hydrological conditions are influenced by a road passing through its former area. The road drain accelerates drying mechanisms, favouring thus vascular plants settlement to the detriment of specific flora of peatlands (i.e. Sphagnum). Hydrological restoration was undertaken in February 2014. It consisted in building thresholds to slow down drain runoff and to promote the soil rewetting. Two transects of piezometers were settled in independent two hydrological sub-systems: Trans-up and Trans-down. Trans-down is supposed to be influenced by the hydrological restoration, while Trans-up is not. These transects cross the peatland and follow water flow direction until the outlet. Six sampling campaigns were performed before, during and after the vegetation period. Water conductivity and pH were measured on site. Water samples were collected in the piezometers. Samples were filtered in the field at 0.45 μm. Concentrations of dissolved organic carbon (DOC), cations (Na+, K+, Ca2+, Mg2+, NH4+) and anions (Cl-, SO42-, PO43-, NO2-, NO3-) were measured. Absorbance was measured by UV-VIS spectrophotometer to assess SUVA254 and aromaticity of DOM. Three-dimensional excitation-emission matrices (EEM) were undertaken to characterise fluorescent DOM (FDOM). Humification (HIX) and biological (BIX) fluorescence indices were calculated. PARAFAC algorithm was used to treat EEMs. Precipitations and water levels were measured automatically by a weather station and automatic probes, respectively. Rain water was

  10. A Robust Control Scheme for Medium-Voltage-Level DVR Implementation

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, Poh Chiang; Li, Yun Wei;

    2007-01-01

    In this paper, a robust control scheme with an outer Hinfin voltage control loop and an inner current control loop is designed and implemented on a medium-voltage (MV)-level dynamic voltage restorer (DVR) system. Through a simple selection of weighting functions, the synthesized Hinfin controller....../nonlinear load and induction motor load) conditions. It is shown that the proposed control scheme is effective in both balanced and unbalanced sag compensation and load disturbance rejection, as its robustness is explicitly specified....... of Hinfin controller weighting function selection, inner current loop tuning, and system disturbance rejection capability is presented. Finally, the designed control scheme is extensively tested on a laboratory 10-kV MV-level DVR system with varying voltage sag (balanced and unbalanced) and loading (linear...

  11. Optimized Control Strategy for a Medium-Voltage DVR-Theoretical Investigations and Experimental Results

    DEFF Research Database (Denmark)

    Meyer, Christoph; De Doncker, Rik W.; Li, Yun Wei;

    2008-01-01

    a small fraction of the energy stored in the DC-link capacitor is used, which makes it impractical for DVRs to compensate relatively long voltage sags. Present control strategies are only able to minimize the distortions at the load or to allow a better utilization of the storage system by minimizing......Most power quality problems in distribution systems are related to voltage sags. Therefore, different solutions have been examined to compensate these sags to avoid production losses at sensitive loads. Dynamic voltage restorers (DVRs) have been proposed to provide higher power quality. Currently......, a system wide integration of DVRs is hampered because of their high cost, in particular, due to the expensive DC-link energy storage devices. The cost of these DC-link capacitors remains high because the DVR requires a minimum DC-link voltage to be able to operate and to compensate a sag. As a result, only...

  12. A Study on the Innovation Cost and Effectiveness Evaluation of Compensation Devices for Voltage Sags

    Science.gov (United States)

    Lang, Xuhui; Hara, Ryoichi; Kita, Hiroyuki; Tanaka, Eiichi; Hasegawa, Jun; Kubo, Hiroshi; Yonaga, Shigeru

    Due to the advancement of information technology and widespread use of power electronic devices in recent years, many customers in various fields have suffered from the voltage sag problem. In order to compensate voltage sags, sensitive loads have been primarily equipped with uninterruptible power supplies (UPS) by each consumer individually. Because consumers have many individual needs, this topic becomes an important problem to be considered by quality consultants in the electric utility industry. Based on this situation, we present the applications of UPS and dynamic voltage restorer (DVR) as compensation devices of voltage sags. By considering the need for power quality, we examine the cost-efficiency of both devices quantitatively. Simulations are carried out and the results are shown in this paper.

  13. Analysis of the Relationship Between Dynamic Load Characteristics and Voltage Stability%浅析负荷动态特性与电压稳定性的关系

    Institute of Scientific and Technical Information of China (English)

    廖青华; 张锐

    2011-01-01

    阐述了电压稳定的定义与电压失稳机理,对电压稳定与负荷动态特性的关系进行了定性分析,强调了负荷动态特性在电压稳定分析中的重要作用,指出了目前用于电压稳定分析的动态负荷模型存在的问题,说明建立恰当的动态负荷模型是确保电压稳定分析准确性的关键。%Definition of voltage stability and mechanics of voltage collapse are presented. The relationship between voltage stability and Dynamic Load Characteristics is qualitatively analyzed. The importance of Dynamic Load Characteristics in voltage stability analysis is emphasized. The problems of Dynamic Load model in voltage stability analysis at present are pointed out. Appropriate modeling of Dynamic Load is crucial in accurate voltage stability analysis.

  14. Voltage Stabilization of a Wind Turbine with STATCOM Using Intelligent Control Techniques

    Directory of Open Access Journals (Sweden)

    S. A. Gawish

    2016-03-01

    Full Text Available Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind System is investigated. The essential feature of the STATCOM is that it has the ability to absorb or inject fastly reactive power with power grid. Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the wind system at suddenly step up or down in wind speed is obtained with STATCOM. This paper describes a complete simulation of voltage regulation of a wind system using STATCOM. Conventional control technique as proportional plus integral controller , and intelligent techniques as FLC and ANFIS are used in this work. The control technique is performed using MATLAB package software. The dynamic response of uncontrolled system is also investigated under wide range of disturbances. The voltage regulation by using STATCOM whose output is varied so as to maintain or control output voltage in the system. The dynamic response of controlled system is shown and comparison between the uncontrolled system and the controlled system is described to assure the validity of the proposed controller. Also comparison between the proposed control methods scheme is presented. To validate the powerful of the STATCOM FACTS controllers, the studied power system is simulated and subjected to different severe disturbances. The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability and voltage.

  15. Site Preparation Drives Long-Term Plant Community Dynamics in Restored Tallgrass Prairie: A Case Study in Southeastern South Dakota

    Science.gov (United States)

    Millikin, Alice R.; Jarchow, Meghann E.; Olmstead, Karen L.; Krentz, Rustan E.; Dixon, Mark D.

    2016-10-01

    Most tallgrass prairies have been destroyed or altered, making restoration an important component to their conservation. Our goal was to evaluate progress 12-years post-restoration at Spirit Mound Historic Prairie and determine whether the outcomes varied based on different land use and restoration histories across the site. We examined changes in plant diversity, richness, evenness, non-native species relative abundance, and community composition from 2004 to 2013. Areas with different restoration treatments and land-use histories showed divergent results. Seventy percent of the site, previously annual row crop, was reconstructed using herbicide application followed by native seeding (hereafter reconstruction). Areas that were previously grazed, 15 % of the site, were restored with only partial seeding and no herbicide treatment (hereafter rehabilitation). Species richness and diversity increased over 40 % in the reconstruction since 2004 and remained over 1.9 times higher in the reconstructed areas than rehabilitated areas. Diversity did not change in the rehabilitation, but richness increased 47 % since 2004. Evenness decreased 11-26 % over time in both areas. Non-native species relative abundance did not change from 2004 to 2013, and remained five times higher in the rehabilitation than the reconstruction. Native C4 grass and forb abundance increased over time in the reconstruction, whereas non-native C3 grasses remained dominant in the rehabilitation. These results showed that restoration outcomes were radically different 12-years post-restoration among areas with different prior land uses that were subjected to different restoration practices. Long-term assessments are important to accurately determine restoration progress and inform management decisions.

  16. Optimal load shedding and restoration

    Science.gov (United States)

    Xu, Ding

    Load shedding is an emergency control action in power systems that can save systems from a wide-area blackout. Underfrequency load shedding, steady state load shedding, and voltage load shedding are widely used in power systems. These methods utilize either the steady state model or a simplified dynamic model to represent a power systems. In this dissertation, a general optimal load shedding method that considers both the dynamic process and load distribution is proposed. The unfavorable load shedding is then formulated as an optimization problem with the objective function of cost minimization. This objective function is subjected to system, security, and operation constraints. The entire problem becomes a question of optimization with differential and nonlinear equations as constraints. To solve this problem, discretization is used to change the differential equations into algebraic equations. The original problem is thus reformulated as an optimization problem and can be solved by a standard mathematical program. The general idea is then applied to traditional power systems, deregulated power systems, power systems with distributed generation, and load restoration. In the traditional power system, the method shows that governor action, generation dynamic, disturbance location, and economic factors can be taken into consideration. In the deregulated power system, two power market models are developed and incorporated into the load shedding scheme. In power systems with multiple distributed generations, the different cases of disturbances are analyzed and models of different distributed generation developed. The general idea is then applied. Finally, the load restoration problem is studied, and it is proposed that an optimization method be applied to it. This dissertation provides a comprehensive solution for load shedding problem in power systems. The models developed in this research can also be used to study other power system problems.

  17. Diverse and Dynamic Expression Patterns of Voltage-Gated Ion Channel Genes in Rat Cochlear Hair Cells

    Science.gov (United States)

    Beisel, K. W.; Fritzsch, B.

    2003-02-01

    Both qualitative and quantitative differences in ion-channel conductances are observed along the tonotopic axis of the mammalian cochlea. We have used a molecular approach to characterize these longitudinal expression patterns of voltage-gated ion-channel (VgCN) superfamily members in the peripheral auditory system. Initially RT-PCR and sequence analyses identified the VgCN α and accessory subunits of the cochlear hair cell (HC). Next, whole mount in situ hybridizations demonstrated at least seven common longitudinal expression patterns with the apex tip and basal hook region having the greatest in disparity. These data suggest potential topological variations in hair-cell electrophysiological signatures and these gradients may contribute to cochlear HC's ability to function as efficient frequency analyzers.

  18. Hierarchical Control Scheme for Voltage Unbalance Compensation in Islanded Microgrids

    DEFF Research Database (Denmark)

    Savaghebi, Mehdi; Guerrero, Josep M.; Jalilian, Alireza;

    2011-01-01

    active and reactive power controllers, virtual impedance loop and voltage and current controllers. The secondary level is designed to compensate the voltage unbalance at the load bus (LB) of the islanded microgrid. Also, restoration of LB voltage amplitude and microgrid frequency to the rated values...... is considered in the secondary level. These functions are achieved by proper control of distributed generators (DGs) interface converters. The presented simulation results show the effectiveness of the proposed control structure in compensating the voltage unbalance and restoring the voltage amplitude...

  19. Dynamic modelling and robust current control of wind-turbine driven DFIG during external AC voltage dip

    Institute of Scientific and Technical Information of China (English)

    HU Jia-bing; HE Yi-kang

    2006-01-01

    Doubly-FedInduction Generator (DFIG), with vector control applied, is widely used in Variable-Speed ConstantFrequency (VSCF) windenergy generation system and shows good performance in maximum wind energy capture. But in two traditional vector control schemes, the equivalent stator magnetizing current is considered invariant in order to simplify the rotor current inner-loop controller. The two schemes can perform very well when the grid is in normal condition. However, when grid disturbance such as grid voltage dip or swell fault occurs, the control performance worsens, the rotor over current occurs and the Fault Ride-Through (FRT) capability of the DFIG wind energy generation system gets seriously deteriorated. An accurate DFIG model was used to deeply investigate the deficiency of the traditional vector control. The improved control schemes of two typical traditional vector control schemes used in DFIG were proposed, and simulation study of the proposed and traditional control schemes, with robust rotor current control using Internal Model Control (IMC) method, was carried out. The validity of the proposed modified schemes to control the rotor current and to improve the FRT capability of the DFIG wind energy generation system was proved by the comparison study.

  20. Effects of Restoration Techniques on Soil Carbon and Nitrogen Dynamics in Florida Longleaf Pine (Pinus palustris Sandhill Forests

    Directory of Open Access Journals (Sweden)

    Martin Lavoie

    2014-03-01

    Full Text Available Historic fire suppression and intensive forest management in longleaf pine (Pinus palustris sandhill forests has resulted in hardwood encroachment and degradation of this fire-dependent ecosystem. Active management is now required to restore native community structure and composition, but little is known about the long-term impacts of typical restoration techniques on ecosystem properties. In 1994, the Longleaf Pine Restoration Project (LPRP was established in fire-excluded longleaf pine sandhills of Eglin Air Force Base, Florida, to explore the effects of restoration treatments on plant and animal community composition and soil processes. Experimental treatments applied included three hardwood reduction techniques and delayed burn. Reference sites were concurrently monitored. Fifteen years later, we revisited the LPRP plots to determine whether soil processes showed lasting treatment effects. This study showed that there were no differences in soil C and N between the reference and the fire-suppressed plots prior to the treatments, suggesting that soil C and N were relatively resistant to degradation. This study also showed that the restoration treatments had a significant effect by reducing soil C, but this effect was only short-lived (<3 years. In addition, a MRPP (multi-response permutation procedure analysis showed that only the herbicide treatment was still different from the reference plots 15 years after the initial treatments. Thus, this study suggests that repeated fires (or lack of or hardwood removal treatments have little detectable effect on soil nutrients in these nutrient-poor ecosystems.

  1. Charged particle dynamics and process control in capacitive RF discharges driven by tailored voltage waveforms in mixtures of Argon and CF4

    Science.gov (United States)

    Brandt, Steven; Donko, Zoltan; Schulze, Julian

    2016-09-01

    The electron power absorption dynamics and the Electrical Asymmetry Effect (EAE) are computationally investigated for Argon-CF4 gas mixtures in geometrically symmetric capacitively coupled plasmas. Simulations are performed for both single- and triple-frequency tailored voltage waveforms at 20 and 60 Pa, using a fundamental frequency of 13.56 MHz and its consecutive harmonics. The results at 60 Pa show electron power absorption mode transitions between the Drift-Ambipolar (DA) mode and the α-mode induced by varying the admixture of Ar to CF4, which leads to a change of the plasma chemistry. In the triple-frequency cases small argon admixtures (of the order of 10%) strongly affect the electron power absorption dynamics and the symmetry of the discharge. The change of the electrical generation of a DC self-bias via the EAE, the ion flux-energy distribution functions of different ion species at the electrodes, and the excitation of resonance effects are studied as a function of the mixing ratio of these two gases. The results are expected to be highly relevant for plasma processing, where such gas mixtures are often used.

  2. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  3. A Comprehensive Review of Low-Voltage-Ride-Through Methods for Fixed-Speed Wind Power Generators

    DEFF Research Database (Denmark)

    Moghadasi, Amirhasan; Sarwat, Arif; Guerrero, Josep M.

    2016-01-01

    This paper presents a comprehensive review of various techniques employed to enhance the low voltage ride through (LVRT) capability of the fixed-speed induction generators (FSIGs)-based wind turbines (WTs), which has a non-negligible 20% contribution of the existing wind energy in the world....... For verification purposes, several simulations are presented in MATLAB software to demonstrate and compare the reviewed LVRT schemes. Based on the simulated results, series connection dynamic voltage restorer (DVR) and shunt connection static synchronous compensators (STATCOM) are the highly efficient LVRT...

  4. Distributed Optimal Control of Reactive Power and Voltage in Islanded Microgrids

    DEFF Research Database (Denmark)

    Wang, Yanbo; Wang, Xiongfei; Chen, Zhe

    2017-01-01

    This paper presents a distributed optimal control strategy for islanded microgrids, which allows to perform reactive power sharing and voltage regulation without using communication system. To perform the twofold objectives, a small signal model is first developed to reconstruct the system input...... performance of the optimal controller is analyzed, from which the guideline for choosing controller parameters is formulated. The results obtained from sensitivity analysis, simulations and experiments show that the proposed approach provides the expected reliability and flexibility for optimizing......-output relationship, which is evaluated through sensitivity analysis. A state estimator is then constructed to observe reactive power distribution and system voltages by local measurement. An optimal regulator is developed to perform both reactive power sharing and system voltage restoration. And the dynamic...

  5. Distributed Optimal Control of Reactive Power and Voltage in Islanded Microgrids

    DEFF Research Database (Denmark)

    Wang, Yanbo; Wang, Xiongfei; Chen, Zhe

    2016-01-01

    The paper proposes a distributed optimal control strategy for islanded microgrids, which allows to perform reactive power sharing and voltage regulation without communication system. To realize the twofold objective, an improved small signal model is developed first to reconstruct the system input...... power sharing and system voltage restoration. And the dynamic performance of the optimal controller is analyzed, from which the guideline for choosing controller parameters is formulated. The results obtained from sensitivity analysis, simulations and experiments show that the proposed approach provides......-output relationship, where the relationship is evaluated with sensitivity analysis. A state estimator is then constructed based on the new input-output relationship in order to observe reactive power distribution and system voltages by local measurement. An optimal regulator is developed to perform both reactive...

  6. Voice restoration

    NARCIS (Netherlands)

    Hilgers, F.J.M.; Balm, A.J.M.; van den Brekel, M.W.M.; Tan, I.B.; Remacle, M.; Eckel, H.E.

    2010-01-01

    Surgical prosthetic voice restoration is the best possible option for patients to regain oral communication after total laryngectomy. It is considered to be the present "gold standard" for voice rehabilitation of laryngectomized individuals. Surgical prosthetic voice restoration, in essence, is alwa

  7. Dynamic globularization and restoration mechanism of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy during isothermal compression

    Energy Technology Data Exchange (ETDEWEB)

    Li, L.; Luo, J.; Yan, J.J.; Li, M.Q., E-mail: honeymli@nwpu.edu.cn

    2015-02-15

    Highlights: • We discussed globularization mechanism in a near β titanium alloy. • We analyzed recrystallization mechanism considering the effect of α grains and recovery. • We made detailed quantitative analysis on the microstructure evolution. • We analyzed the texture evolution during recrystallization. - Abstract: Dynamic globularization and restoration mechanism of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy during isothermal compression were investigated by employing a high-resolution electron backscatter diffraction technique (EBSD). Quantitative analysis was made in detail for further understanding the microstructure evolution. The results reveal that the dynamic globularization of primary α grains of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy is accomplished by the formation of high-angle boundaries (HABs) and the penetration of the β phase during isothermal compression, and an increase in deformation temperature leads to a more globular microstructure. The main restoration mechanism in the β phase of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy during isothermal compression is dynamic recovery (DRC) at a strain rate of 0.01 s{sup -1}, while continuous dynamic recrystallization (CDRX) occurs as the strain rate increases to 1.0 s{sup -1}/5.0 s{sup -1} and the α grains play an important role in recrystallization. The recrystallization in the β phase of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy during isothermal compression is promoted with the decreasing of deformation temperature and the increasing of strain rate. A strong 〈0 0 1〉 fiber texture develops where only DRC occurs and the deformation texture is weakened to a large extent after recrystallization of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy during isothermal compression.

  8. A Digitally Dynamic Power Supply Technique for 16-Channel 12 V-Tolerant Stimulator Realized in a 0.18-μm 1.8-V/3.3-V Low-Voltage CMOS Process.

    Science.gov (United States)

    Luo, Zhicong; Ker, Ming-Dou; Yang, Tzu-Yi; Cheng, Wan-Hsueh

    2017-07-18

    A new digitally dynamic power supply technique for 16-channel 12-V-tolerant stimulator is proposed and realized in a 0.18-μm 1.8-V/3.3-V CMOS process. The proposed stimulator uses four stacked transistors as the pull-down switch and pull-up switch to withstand 4 times the nominal supply voltage (4 × V DD). With the dc input voltage of 3.3 V, the regulated three-stage charge pump, which is capable of providing 11.3-V voltage at 3-mA loading current, achieves dc conversion efficiency of up to 69% with 400-pF integrated capacitance. Power consumption is reduced by implementing the regulated charge pump to provide a dynamic dc output voltage with a 0.5-V step. The proposed digitally dynamic power supply technique, which is implemented by using a p-type metal oxide semiconductor (PMOS) inverter with pull-down current source and digital controller, greatly improves the power efficiency of a system. The silicon area of the stimulator is approximately 3.5 mm2 for a 16-channel implementation. The functionalities of the proposed stimulator have been successfully verified through animal test.

  9. Efficient Scheduling of Scientific Workflows with Energy Reduction Using Novel Discrete Particle Swarm Optimization and Dynamic Voltage Scaling for Computational Grids

    Directory of Open Access Journals (Sweden)

    M. Christobel

    2015-01-01

    Full Text Available One of the most significant and the topmost parameters in the real world computing environment is energy. Minimizing energy imposes benefits like reduction in power consumption, decrease in cooling rates of the computing processors, provision of a green environment, and so forth. In fact, computation time and energy are directly proportional to each other and the minimization of computation time may yield a cost effective energy consumption. Proficient scheduling of Bag-of-Tasks in the grid environment ravages in minimum computation time. In this paper, a novel discrete particle swarm optimization (DPSO algorithm based on the particle’s best position (pbDPSO and global best position (gbDPSO is adopted to find the global optimal solution for higher dimensions. This novel DPSO yields better schedule with minimum computation time compared to Earliest Deadline First (EDF and First Come First Serve (FCFS algorithms which comparably reduces energy. Other scheduling parameters, such as job completion ratio and lateness, are also calculated and compared with EDF and FCFS. An energy improvement of up to 28% was obtained when Makespan Conservative Energy Reduction (MCER and Dynamic Voltage Scaling (DVS were used in the proposed DPSO algorithm.

  10. Farnesyltransferase inhibitor treatment restores chromosome territory positions and active chromosome dynamics in Hutchinson-Gilford progeria syndrome cells

    Science.gov (United States)

    2011-01-01

    Background Hutchinson-Gilford progeria syndrome (HGPS) is a premature ageing syndrome that affects children leading to premature death, usually from heart infarction or strokes, making this syndrome similar to normative ageing. HGPS is commonly caused by a mutation in the A-type lamin gene, LMNA (G608G). This leads to the expression of an aberrant truncated lamin A protein, progerin. Progerin cannot be processed as wild-type pre-lamin A and remains farnesylated, leading to its aberrant behavior during interphase and mitosis. Farnesyltransferase inhibitors prevent the accumulation of farnesylated progerin, producing a less toxic protein. Results We have found that in proliferating fibroblasts derived from HGPS patients the nuclear location of interphase chromosomes differs from control proliferating cells and mimics that of control quiescent fibroblasts, with smaller chromosomes toward the nuclear interior and larger chromosomes toward the nuclear periphery. For this study we have treated HGPS fibroblasts with farnesyltransferase inhibitors and analyzed the nuclear location of individual chromosome territories. We have found that after exposure to farnesyltransferase inhibitors mis-localized chromosome territories were restored to a nuclear position akin to chromosomes in proliferating control cells. Furthermore, not only has this treatment afforded chromosomes to be repositioned but has also restored the machinery that controls their rapid movement upon serum removal. This machinery contains nuclear myosin 1β, whose distribution is also restored after farnesyltransferase inhibitor treatment of HGPS cells. Conclusions This study not only progresses the understanding of genome behavior in HGPS cells but demonstrates that interphase chromosome movement requires processed lamin A. PMID:21838864

  11. Voltage stability analysis considering the load dynamic characteristics and the voltage control devices; Analisis de estabilidad de voltaje considerando las caracteristicas dinamicas de la carga y dispositivos de control de voltaje

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez Alvarez, Enrique

    2001-09-15

    The research work presented in this thesis, is centered in the voltage stability analysis of medium term considering the effect of the load characteristics and its interaction with the voltage control device models in the transmission network. More concretely, a type of load model is defined and studied with desirable characteristics for the study of the voltage stability, the generic load models derived from field tests and from the application of identification techniques and it is analyzed the influence of the application of control systems to improve the system stability margins. Also, alternatives to the power system modeling for the voltage stability study in complex systems are reviewed. In the first place a fundamental analysis of the voltage characteristics and stability in a simplified power system is presented and the method of adopted analysis is introduced. It is shown that the instability phenomenon is manifested as a singular type bifurcation induced from the critical way of voltage when the system is operated under stress conditions. Next, the contribution of the action of the control devices to the stability margin is analyzed and criteria of the stability analyses are deducted based on the study of such mode. Following a linear model of the power system with desirable characteristics for the study of the voltage stability of medium term is proposed and the characteristics of stability in the context of the study of complex systems are interpreted. The proposed analysis tool is based on the physical notion that the behavior of the voltage control systems in the generators is very rapid with regard to the behavior of the load and has its main application in the preliminary study of the voltage stability of medium and long term. From this model, an analytical tool based on the application of techniques of linear analysis is proposed to approach the problem of determination of critical voltage areas and the contribution of control devices to the

  12. Restoring forests

    DEFF Research Database (Denmark)

    Jacobs, Douglass F.; Oliet, Juan A.; Aronson, James

    2015-01-01

    of land requiring restoration implies the need for spatial prioritization of restoration efforts according to cost-benefit analyses that include ecological risks. To design resistant and resilient ecosystems that can adapt to emerging circumstances, an adaptive management approach is needed. Global change......, in particular, imparts a high degree of uncertainty about the future ecological and societal conditions of forest ecosystems to be restored, as well as their desired goods and services. We must also reconsider the suite of species incorporated into restoration with the aim of moving toward more stress resistant...... and competitive combinations in the longer term. Non-native species may serve an important role under some circumstances, e.g., to facilitate reintroduction of native species. Propagation and field establishment techniques must promote survival through seedling stress resistance and site preparation. An improved...

  13. Dynamic Simulation Investigation of 750kV Stepped Switching Controllable High Voltage Shunt Reactor%750kV分级投切式可控高压并联电抗器的动态模拟研究

    Institute of Scientific and Technical Information of China (English)

    秦睿; 郭文科; 王惠中

    2012-01-01

    This paper describes the stepped switching controllable high voltage shunt reactors basic principle, the device can regulate the system reactive power, voltage and frequency over inhibition of arc current, with a continuous smooth power adjustable, harmonic current is small and the advantages of fast response. It analyzes the stepped switching controllable high voltage shunt reactor protection features and functionality, protection and circuit breaker protection, mainly to explain the valve protection and circuit breaker protection. According to the stepped switching controllable high voltage shunt reactors principles and technical characteristics, combined with power system dynamic simulation laboratory simulation system characteristics, stepped switching controllable high voltage shunt reactor protection system dynamic simulation experimental research, besides valve and circuit breaker protection dynamic simulation test results are necessary analysis and research.%主要分析了分级投切式可控高压并联电抗器保护的特点和功能,对阀保护和断路器保护进行了说明,并对阀保护和断路器保护动态模拟试验结果进行了必要的分析和研究.根据分级投切式可控高压并联电抗器的原理和技术特点,结合试验室电力系统动态模拟仿真系统的特点,对分级投切式可控高压并联电抗器的保护系统进行了动态模拟试验研究.

  14. Dynamic Restoration Processes in a 23Cr-6Ni-3Mo Duplex Stainless Steel: Effect of Austenite Morphology and Interface Characteristics

    Science.gov (United States)

    Haghdadi, N.; Cizek, P.; Beladi, H.; Hodgson, P. D.

    2017-07-01

    The austenite and ferrite microstructure evolution and restoration mechanisms were studied during hot uniaxial compression of a 23Cr-6Ni-3Mo duplex stainless steel with two markedly different austenite morphologies (i.e., equiaxed and Widmanstätten). The deformation was performed at a temperature of 1273 K (1000 °C) at a strain rate of 0.1 s-1. The strain was preferentially partitioned in ferrite for both the microstructures studied. Both austenite morphologies displayed frequent splitting into complex-shaped deformation bands, containing dislocation cells and local stacking faults. Equiaxed austenite was favorable to the local development of microbands (MBs), while its Widmanstätten counterpart appeared to be completely resistant to their formation. This was attributed to the complexity of deformation inside the irregularly shaped Widmanstätten plates precluding the formation of self-screening MB arrays. The MB boundaries were typically aligned along highly stressed slip planes. The presence of discontinuous dynamic recrystallization (DDRX) within both the austenite morphologies was very limited. A slightly higher fraction of DDRX was detected in Widmanstätten austenite, compared to equiaxed austenite, which was ascribed to its higher contribution to the overall deformation and lower fraction of low-mobility coherent twin boundaries. Furthermore, it was demonstrated that continuous dynamic recrystallization (CDRX) was the main restoration mechanism within ferrite for both the microstructure types studied. The CDRX development within ferrite was accelerated in the microstructure with equiaxed austenite. This was related to the comparatively lower fraction of coherent interphases in this microstructure, which would hinder the slip transmission across the interphase and make the strain concentrate within ferrite.

  15. Light-induced structural changes in a short light, oxygen, voltage (LOV protein revealed by molecular dynamics simulations – implications for the understanding of LOV photoactivation.

    Directory of Open Access Journals (Sweden)

    Marco eBocola

    2015-10-01

    Full Text Available The modularity of light, oxygen, voltage (LOV blue-light photoreceptors has recently been exploited for the design of LOV-based optogenetic tools, which allow the light-dependent control of biological functions. For the understanding of LOV sensory function and hence the optimal design of LOV-based optogentic tools it is essential to gain an in depth atomic-level understanding of the underlying photoactivation and intramolecular signal-relay mechanisms. To address this question we performed molecular dynamics simulations on both the dark- and light-adapted state of PpSB1-LOV, a short dimeric bacterial LOV-photoreceptor protein, recently crystallized under constant illumination. While LOV dimers remained globally stable during the light-state simulation with regard to the Jα coiled-coil, distinct conformational changes for a glutamine in the vicinity of the FMN chromophore are observed. In contrast, multiple Jα-helix conformations are sampled in the dark-state. These changes coincide with a displacement of the Iβ and Hβ strands relative to the light-state structure and result in a correlated rotation of both LOV core domains in the dimer. These global changes are most likely initiated by the reorientation of the conserved glutamine Q116, whose side chain flips between the Aβ (dark state and Hβ strand (light state, while maintaining two potential hydrogen bonds to FMN-N5 and FMN-O4, respectively. This local Q116-FMN reorientation impacts on an inter-subunit salt-bridge (K117-E96, which is stabilized in the light state, hence accounting for the observed decreased mobility. Based on these findings we propose an alternative mechanism for dimeric LOV photoactivation and intramolecular signal-relay, assigning a distinct structural role for the conserved flipping glutamine. The proposed mechanism is discussed in light of universal applicability and its implications for the understanding of LOV-based optogenetic tools.

  16. Floodplain restoration on the upper Danube by re-establishing back water dynamics: first results of the hydro-geomorphological monitoring

    Science.gov (United States)

    Fischer, Peter; Hilger, Ludwig; Cyffka, Bernd

    2013-04-01

    Within the framework of a restoration project at the upper Danube, eight working groups of different scientific disciplines have been operating since 2009. They investigate the changes evoked through the accomplished restoration measures, which seek to bring back new dynamics to the floodplain and to reconnect it with the river in order to optimize flood plain ecological functioning. Main object is the identification and analysis of hydro-geomorphological processes and their impact on vegetation and fauna. Hydrology is one of the key factors determining the type and function of flood plains and thus alternating water levels are the motor of riparian ecosystems. Diverse water and groundwater levels and particularly flood events affect and support floodplain typical vegetation and animal species. All floodplain waterbodies (oxbows, floodplain ponds, backwaters and sidearms) are more or less connected by surface or subsurface waterways. Hydrological conditions are mainly influenced by the following measures: a, permanent nature orientated bypass river with a discharge of up to 5 m3/s; b, man controlled ecological flooding (discharge of up to 30 m3/s); c, groundwater drawdown in the eastern project area. These measures shall bring back "former" natural hydrological dynamics to the floodplain. They establish geomorphological processes and forms as well and create a mosaic of typical habitats. River morphology is monitored by terrestrial laser scanning analysing the so attained data sets, erosion and aggregation rates at selected undercut slopes and point bars can be detected with a high resolution. Large scale mapping by a drone and dGPS mapping are very helpful tools for identifing widespread flooding areas. Further methods such as, cross section and bed load measurements complete the research work. The aim is to link the interaction of these abiotic processes with the biotic nature and determine the importance of geomorphological disturbance for floodplain ecosystems

  17. ramic restorations

    Directory of Open Access Journals (Sweden)

    Ashish R Jain

    2013-01-01

    Full Text Available Rehabilitation of a patient with severely worn dentition after restoring the vertical dimension is a complex procedure and assessment of the vertical dimension is an important aspect in these cases. This clinical report describes the full mouth rehabilitation of a patient who was clinically monitored to evaluate the adaptation to a removable occlusal splint to restore vertical dimension for a period 1 month and provisional restorations to determine esthetic and functional outcome for a period of 3 months. It is necessary to recognizing that form follows function and that anterior teeth play a vital role in the maintenance of oral health. Confirmation of tolerance to changes in the vertical dimension of occlusion (VDO is of paramount importance. Articulated study casts and a diagnostic wax-up can provide important information for the evaluation of treatment options. Alteration of the VDO should be conservative and should not be changed without careful consideration.

  18. Use of Fourier domain filtering and dynamic programming in finding a titanium coil implant in high voltage x-ray images

    DEFF Research Database (Denmark)

    Nielsen, Henning; Hansen, Jesper Carl

    2006-01-01

    This paper deals with the problem of finding precise position and orientation of a titanium coil implant in humans. Analysis of high voltage X-rays stereo images are used to determine the true 3D position. High voltage images inherently presents with poor contrast. Various image processing techni...... determined the position of the titanium wire within less than 1 mm of ground truth determined from manual analysis of the images....

  19. Consequences of marginal drainage from a raised bog and understanding the hydrogeological dynamics as a basis for restoration

    Science.gov (United States)

    Regan, Shane; Johnston, Paul

    2010-05-01

    of vertical water losses in the peat profile not confined to the bog margins. Distinct zones of groundwater seepage in the marginal drains have been mapped based on hydrochemical and stable isotopic composition of the water and occur where drains have cut into permeable subsoil beneath the peat substrate and where the potentiometric surface of the regional groundwater table is below, or coincident with, the elevation at the base of the drain. Groundwater as a ‘supporting' ecological condition is usually confined to the perimeter of a raised bog, where peat and underlying clay thin towards the margin, allowing regional groundwater and peat water to converge and mix, thereby giving rise to characteristic nutrient rich ‘lagg' zone vegetation. However, in Clara Bog West it appears there is also a connection between the regional groundwater table and the high bog. Such a connection appears to be unique to Clara Bog West as a result of the prevailing geological conditions. A succession of Carboniferous Limestone to relatively permeable glacial till deposits to low permeability lacustrine clay sediment is the predominant underlying geology of the bog. However, there are areas where the glacial till protrudes through the lacustrine clay, which ordinarily isolates the high bog from underlying groundwater, thereby engendering a dependency on regional groundwater conditions. The hydrogeological data now suggest that drainage at the bog margin has created a hydraulic connection between these ‘subsoil subcrops' and the marginal drains, developed within the same subsoil, thereby lowering the regional groundwater table, steepening the hydraulic gradient and resulting in significant water loss from the main bog body. As such, understanding this hydrogeological connection is central to restoration activities that will aim to arrest subsidence and restore water levels that are indicative for ecotope development, on the high bog. Acknowledgements Clara Restoration Group: Jan

  20. The effect of applied control strategy on the current-voltage correlation of a solid oxide fuel cell stack during dynamic operation

    Directory of Open Access Journals (Sweden)

    Szmyd Janusz S.

    2014-09-01

    Full Text Available This paper discusses the transient characteristics of the planar type SOFC cell stack, of which the standard output is 300 W. The transient response of the voltage to the manipulation of an electric current was investigated. The effects of the response and of the operating condition determined by the operating temperature of the stack were studied by mapping a current-voltage (I-V correlation. The current-based fuel control (CBFC was adopted for keeping the fuel utilization factor at constant while the value of the electric current was ramped at the constant rate. The present experimental study shows that the transient characteristics of the cell voltage are determined by primarily the operating temperature caused by the manipulation of the current. Particularly, the slope of the I-V curve and the overshoot found on the voltage was remarkably influenced by the operating temperature. The different values of the fuel utilization factor influence the height of the settled voltages. The CBFC has significance in determining the slope of the I-V characteristic, but the different values ofthe fuel utilization factor does not affect the slope as the operating temperature does. The CBFC essentially does not alter the amplitude of the overshoot on the voltage response, since this is dominated by the operating temperature and its change is caused by manipulating the current.

  1. Parameter estimation of stable models and with minimum phase in dynamic aggregation of voltage regulators; Estimacao de parametros de modelos estaveis e de fase minima na agregacao dinamica de reguladores de tensao

    Energy Technology Data Exchange (ETDEWEB)

    Souza, E.J.S. Pires de [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio), Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Eletrica], E-mail: pires@ele.puc-rio.br

    2009-07-01

    The dynamic aggregation of coherent generating unit models has been solved as an unconstrained optimization problem. In this process, negative time constants may be obtained, which characterize unstable or non-minimal phase models. The comparison of the solutions of the dynamic aggregation problem of voltage regulator models obtained with both the original formulation and the squared-variable transformation is the objective of this paper. Initial values are within the range from +100% to -90% in relation to the estimated parameters. The New England system including models of the Brazilian system is considered in the studies. (author)

  2. Quantifying the effectiveness of ecological restoration projects on long-term vegetation dynamics in the karst regions of Southwest China

    Science.gov (United States)

    Tong, Xiaowei; Wang, Kelin; Yue, Yuemin; Brandt, Martin; Liu, Bo; Zhang, Chunhua; Liao, Chujie; Fensholt, Rasmus

    2017-02-01

    To alleviate the severe rocky desertification and improve the ecological degradation conditions in Southwest China, the national and local Chinese governments have implemented a series of Ecological Restoration Projects (ERPs) since the late 1990s. This study proposed a remote sensing based approach to evaluate the long-term efforts of the ERPs started in 2000. The method applies a time-series trend analysis of satellite based vegetation data corrected for climatic influences to reveal human induced vegetation changes. The improved residual method is combined with statistics on the invested project funds to derive an index, Project Effectiveness Index (PEI), measuring the project effectiveness at county scale. High effectiveness is detected in the Guangxi Province, moderate effectiveness in the Guizhou Province, and low and no effectiveness in the Yunnan Province. Successful implementations are closely related to the combined influences from climatic conditions and human management. The landforms of Peak Forest Plain and Peak Cluster Depression regions in the Guangxi Province are characterized by temperate climate with sufficient rainfall generally leading to a high effectiveness. For the karst regions of the Yunnan and Guizhou Provinces with rough terrain and lower rainfall combined with poor management practices (unsuitable species selection, low compensation rate for peasants), only low or even no effect of project implementations can be observed. However, the effectiveness distribution is not homogeneous and counties with high project effectiveness in spite of complex natural conditions were identified, while counties with negative vegetation trends despite relatively favorable conditions and high investments were also distinguished. The proposed framework is expected to be of high relevance in general monitoring of the successfulness of ecological conservation projects in relation to invested funds.

  3. Environmental Restoration

    Energy Technology Data Exchange (ETDEWEB)

    Zeevaert, T.; Vanmarcke, H

    1998-07-01

    The objectives of SCK-CEN's programme on environmental restoration are (1) to optimize and validate models for the impact assessment from environmental, radioactive contaminations, including waste disposal or discharge; (2) to support the policy of national authorities for public health and radioactive waste management. Progress and achievements in 1997 are reported.

  4. Site Restoration

    Energy Technology Data Exchange (ETDEWEB)

    Noynaert, L.; Bruggeman, A.; Cornelissen, R.; Massaut, V.; Rahier, A

    2001-04-01

    The objectives, the programme, and the achievements of the Site Restoration Department of SCK-CEN in 2000 are summarised. Main activities include the decommissioning of the BR3 PWR-reactor as well as other clean-up activities, projects on waste minimisation and activities related to the management of decommissioning projects. The department provides consultancy and services to external organisations.

  5. Restorative neuroscience

    DEFF Research Database (Denmark)

    Andres, Robert H; Meyer, Morten; Ducray, Angélique D

    2008-01-01

    There is increasing interest in the search for therapeutic options for diseases and injuries of the central nervous system (CNS), for which currently no effective treatment strategies are available. Replacement of damaged cells and restoration of function can be accomplished by transplantation of...

  6. Voltage and frequency control in the Islanded portion of the CIGRE Low Voltage distribution network

    DEFF Research Database (Denmark)

    Mustafa, Ghullam; Bak, Claus Leth; Buriro, Ehsan Ali

    2017-01-01

    imbalance in the islanded MG. The voltage and the frequency of the islanded MG can be restored to the permissible limits if the desired/exceeded amount of active and reactive power is injected/absorbed by the locally available sources in islanded MG. This paper proposes the control strategy which can...... by providing some ancillary services. The main focus of this paper is about the development of a control system for the islanded MG, the selection of Voltage-Frequency controller for the most suitable DG unit of the Low Voltage test network and the control of voltage and frequency in islanding condition. Under...... compensate the problems of the voltage and the frequency deviations in the islanded MG. The selection of the VF controller for the most suitable DG unit of the LV test network is also presented in this paper and effectiveness of the controllers is verified by presenting simulation results...

  7. Transient Voltage Recorder

    Science.gov (United States)

    Medelius, Pedro J. (Inventor); Simpson, Howard J. (Inventor)

    2002-01-01

    A voltage transient recorder can detect lightning induced transient voltages. The recorder detects a lightning induced transient voltage and adjusts input amplifiers to accurately record transient voltage magnitudes. The recorder stores voltage data from numerous monitored channels, or devices. The data is time stamped and can be output in real time, or stored for later retrieval. The transient recorder, in one embodiment, includes an analog-to-digital converter and a voltage threshold detector. When an input voltage exceeds a pre-determined voltage threshold, the recorder stores the incoming voltage magnitude and time of arrival. The recorder also determines if its input amplifier circuits clip the incoming signal or if the incoming signal is too low. If the input data is clipped or too low, the recorder adjusts the gain of the amplifier circuits to accurately acquire subsequent components of the lightning induced transients.

  8. Pollination and Restoration

    National Research Council Canada - National Science Library

    Kingsley W. Dixon

    2009-01-01

    Pollination services underpin sustainability of restored ecosystems. Yet, outside of agri-environments, effective restoration of pollinator services in ecological restoration has received little attention...

  9. Charge carrier dynamics investigation of CuInS2 quantum dots films using injected charge extraction by linearly increasing voltage (i-CELIV): the role of ZnS Shell

    Science.gov (United States)

    Bi, Ke; Sui, Ning; Zhang, Liquan; Wang, Yinghui; Liu, Qinghui; Tan, Mingrui; Zhou, Qiang; Zhang, Hanzhuang

    2016-12-01

    The role of ZnS shell on the photo-physical properties within CuInS2/ZnS quantum dots (QDs) is carefully studied in optoelectronic devices. Linearly increasing voltage technique has been employed to investigate the charge carrier dynamics of both CuInS2 and CuInS2/ZnS QDs films. This study shows that charge carriers follow a similar behavior of monomolecular recombination in this film, with their charge transfer rate correlates to the increase of applied voltage. It turns out that the ZnS shell could affect the carrier diffusion process through depressing the trapping states and would build up a potential barrier.

  10. Design of a Practical Dynamic Reactive Power Compensation for Low Voltage System%一种实用型低压动态无功补偿系统设计

    Institute of Scientific and Technical Information of China (English)

    郑帆; 杜晓萍

    2011-01-01

    Design of a practical dynamic reactive power compensation,based on capacitive compensation principle,for low voltage system was introduced in detail.The development and present situation of low voltage reactive power compensation were analyzed.The measuring and calculating methods,compensating strategy,hardware structure and part of the software were given.%该文介绍一种实用型基于容性补偿原理的低压动态无功补偿系统的设计,分析了低压无功补偿的发展现状,给出了该系统的检测计算方法、补偿控制策略、硬件结构以及部分软件流程。

  11. Advanced DVR with Zero-Sequence Voltage Component and Voltage Harmonic Elimination for Three-Phase Three-Wire Distribution Systems

    Directory of Open Access Journals (Sweden)

    Margo P

    2009-11-01

    Full Text Available Dynamic Voltage Restorer (DVR is a power electronics device to protect sensitive load when voltage sag occurs. Commonly, sensitive loads are electronic-based devices which generate harmonics. The magnitude and phase of compensated voltage in DVR depend on grounding system and type of fault. If the system is floating, the zero sequence components do not appear on the load side. Meanwhile, in a neutral grounded system, voltage sag is extremely affected by zero sequence components. A blocking transformer is commonly installed in series with DVR to reduce the effect of zero sequence components. This paper proposes a new DVR control scheme that is capable of eliminating the blocking transformer and reducing harmonic distortion. The system uses fuzzy polar controller to replace the conventional PI or FL controller that is commonly used. By taking into account the zero sequence components in the controller design, the effects of zero sequence components can be compensated. Simulated results show the effectiveness of the proposed DVR controller

  12. A Dynamic Reactive Power Reserve Optimization Method to Enhance Transient Voltage Security%提高暂态电压安全水平的动态无功备用优化方法

    Institute of Scientific and Technical Information of China (English)

    孙全才; 程浩忠; 张健; 王琦; 宋越; 刘明松; 杨堤; 李诗旸

    2015-01-01

    Dynamic reactive power reserve of power system is vital to improve transient voltage security. An novel definition of reactive power reserve considering transient voltage security in transient procession was proposed. Correction coefficient to evaluate reactive power reserve's contribution to transient voltage security was given. Corrected reactive power reserve was computed through trace sensitivity method. Then an optimization model to enhance transient voltage security was built. It was solved by primal dual interior point method. Testing on IEEE 39-node system,it is indicated that three weight coefficients proposed are reasonable and effective. The evaluation method can give consideration both supporting capacity of one bus to the other and demand of reactive power reserve according to severity of faults. The system's transient voltage security is enhanced by the way of optimization of system's dynamic reactive power reserve. Hence, the method proposed can be used to prevent the happening of transient voltage collapse during system's fault.%电力系统动态无功储备对提高系统暂态电压安全水平具有重要作用,因此提出一种在系统暂态过程中考虑暂态电压安全的无功备用概念,并给出其对暂态电压安全贡献的评价方法及相应的修正系数.通过轨迹灵敏度方法实现对修正后的无功源动态无功备用的计算,建立提高系统暂态电压安全水平的无功备用优化模型,利用原对偶内点法进行求解.IEEE 39节点算例结果表明,所提3种权重系数合理、有效,通过该评价方式可以充分考虑到无功备用点对点的支撑能力以及故障严重性对无功备用的要求程度,通过系统动态无功备用的优化可提高系统的整体暂态电压安全水平,因此所提方法能够有效地预防系统故障时暂态电压安全问题的发生.

  13. 基于动态规划算法的故障恢复重构%Service Restoration Based on Dynamic Programming

    Institute of Scientific and Technical Information of China (English)

    张浩; 和敬涵; 薄志谦; 胡伟; 李珂; 周文

    2011-01-01

    A new method is presented to restore the power system based on dynamic programming (DP). After isolated a fault, the out-of service area, which is constructed of load nodes could be divided into several groups, each has one contact branch used for load distribution. These groups sharply decrease the number of calculation loops. According to the different restore orders of the load nodes, operation sequences are produced, which turn the restore problem into a node-string choice. Based on a DP method, operation sequences are used to build a multiple-stage decision model, each contact branch is calculated as one stage, the algorithm is designed to transfer and restore the largest load capacity by optimal choice of the node-string. In each stage, the calculation process records the optimal state and lists the decision variable. The optimal result is obtained at the final stage. This method can be used to power service reconfiguration, when the power capacity is not enough to support all of the out-of service nodes, reducing the time of outage and improve the reliability of system. The proposed method is validated by simulation methods.%提出了一种基于动态规划算法的电网恢复重构方案,将配电网的故障恢复重构过程转化为一个多阶段决策过程并设计了动态规划算法进行求解。该方案以恢复最大容量的非故障失电负荷为目标,通过把非故障失电区的多个负荷节点分割为不同的恢复区,并根据每个分区中不同节点的恢复供电顺序生成计算序列组。以此将非故障失电负荷节点的恢复供电过程构建成适用于动态规划方法求解的重构计算模型。重构算法利用对分区方案的选择来降低整体计算复杂度,并采用有效节点串的提取来减少算法组合数和提高计算效率。文中还应用提出的算法对33节点和69节点的测试系统进行了恢复重构计算,给出了算例比较分析,验证了该方案的有效性。

  14. Neotropical dry forests of the Caribbean: Secondary forest dynamics and restoration in St. Croix, US Virgin Islands

    Science.gov (United States)

    Daley, Brian F.

    Neotropical dry forests exist today mainly as secondary forests heavily influenced by exotic plants. This project analyzes land-cover change and secondary dry forest dynamics in three distinct phases (land cover change, secondary forest succession and forest rehabilitation), using St. Croix, US Virgin Islands as an example. Using Landsat satellite images and other data layers, I created classified land cover maps of St. Croix for 1992 and 2002. Forest was the dominant (56%) cover type on both dates, followed by development, grassland/pastures and water. A land cover change analysis comparing the two images revealed that 15% of the study area experienced a change either to (8%) or from (7%) forest. Grassland was the cover most likely to change and decreased from 16% to 11%, converted primarily to development. The overall result is a landscape trending toward younger forests, and increased forest fragmentation and development. In a second study, vegetation data from a chronosequence of secondary forests was analyzed for changes to forest structure, species composition and presence of exotic species. The leguminous exotic tree Leucaena leucocephala was by far the most frequently observed tree and dominated all stands, except those over 50 years old. Species diversity was significantly ( p50 years after abandonment. In a third experiment, a 'gap planting' method for establishing four rare native tree species was tested on a site experiencing arrested succession. All four species successfully established at >69% survival in 3m diameter gaps artificially created in exotic tree stands. A mulch treatment significantly (p<0.01) increased survival, but not growth. This study demonstrates on St. Croix forest is the primary land cover type and secondary forests are predominant forest type. The species composition of these forests is dynamic, but they tend to be dominated by exotic tree species and over 50 years of natural succession is insufficient time for secondary forest

  15. Simulation and Modeling of 24-Pulse STATCOM in EMTDC/PSCAD Program in Order to Regulate Voltage and Dynamic Stability Improvement

    Directory of Open Access Journals (Sweden)

    Naser Parhizgar

    2012-02-01

    Full Text Available This study starts from the proof of Low Frequency Oscillation (LFO and then points out that there are many ways to study the LFO including its rejection measures. Also in this study one control system is planned in order to regulate voltage at common coupling point (PCC in where STATCOM is installed. This research present a single-machine infinite-bus system with one static synchronous compensator (STATCOM asymmetrically installed as a current source. Together with a classical generator model, the simplest power equation is obtained to give direct and clear physical concepts on synchronizing and damping torque factors. According to the primary equations, some basic issues, such as the relationship of voltage gain control and damping control, operating conditions, and the installation of STATCOM, are investigated in this research. Then, with assistance of proportional controller for voltage regulation and damp control, the digital simulation indicate the necessity of control of STATCOM in damping power system oscillations and supplying regulated voltage support.

  16. Impact dynamics model of long span high voltage transmission lines subjected to iced wire breakage%大跨越高压输电线路覆冰断线的冲击动力学模型

    Institute of Scientific and Technical Information of China (English)

    刘春城; 初佂宇; 孙显鹤; 张伟

    2012-01-01

    In order to theoretically reveal the impact dynamic responses of long span high voltage transmission lines subjected to iced wire breakage, the impact dynamics model for long span high-voltage transmission lines with iced bundled conductors was developed comprehensively by using an equivalent single iced conductor instead of bundled conductors. The impact dynamics model of iced wire breakage was derived by using energy method. Taking a typical tension section of long span high-voltage transmission line as an example, the impact responses under iced wire breakage and non-iced wire breakage were computed by using this model and a good agreements were achieved. The results show that the impact dynamic response under iced wire breakage is larger than that under non-iced wire breakage, so the impact dynamic response due to iced wire breakage should not be ignored. The model can provide a theoretical basis for experiments and numerical simulations of long span high voltage transmission lines under iced wire breakage.%为了从理论上揭示大跨越高压输电线路覆冰断线的冲击动力响应,针对大跨越高压输电导线分裂布置型式的线路覆冰情况,采用等效单根导线代替分裂导线,利用能量法,建立了覆冰断线的冲击动力学模型.以某大跨越高压输电线路的一个典型耐张段为例,应用该模型计算导(地)线覆冰断线和未覆冰断线工况下对铁塔造成的冲击响应.研究表明:覆冰断线造成的冲击动力响应远大于未覆冰断线情况,覆冰断线冲击响应不容忽视.该模型可为大跨越高压输电线路覆冰断线的冲击动力响应试验分析与数值计算提供理论依据.

  17. Automatic voltage imbalance detector

    Science.gov (United States)

    Bobbett, Ronald E.; McCormick, J. Byron; Kerwin, William J.

    1984-01-01

    A device for indicating and preventing damage to voltage cells such as galvanic cells and fuel cells connected in series by detecting sequential voltages and comparing these voltages to adjacent voltage cells. The device is implemented by using operational amplifiers and switching circuitry is provided by transistors. The device can be utilized in battery powered electric vehicles to prevent galvanic cell damage and also in series connected fuel cells to prevent fuel cell damage.

  18. Mixed voltage VLSI design

    Science.gov (United States)

    Panwar, Ramesh; Rennels, David; Alkalaj, Leon

    1993-01-01

    A technique for minimizing the power dissipated in a Very Large Scale Integration (VLSI) chip by lowering the operating voltage without any significant penalty in the chip throughput even though low voltage operation results in slower circuits. Since the overall throughput of a VLSI chip depends on the speed of the critical path(s) in the chip, it may be possible to sustain the throughput rates attained at higher voltages by operating the circuits in the critical path(s) with a high voltage while operating the other circuits with a lower voltage to minimize the power dissipation. The interface between the gates which operate at different voltages is crucial for low power dissipation since the interface may possibly have high static current dissipation thus negating the gains of the low voltage operation. The design of a voltage level translator which does the interface between the low voltage and high voltage circuits without any significant static dissipation is presented. Then, the results of the mixed voltage design using a greedy algorithm on three chips for various operating voltages are presented.

  19. Resonance analysis in parallel voltage-controlled Distributed Generation inverters

    DEFF Research Database (Denmark)

    Wang, Xiongfei; Blaabjerg, Frede; Chen, Zhe

    2013-01-01

    Thanks to the fast responses of the inner voltage and current control loops, the dynamic behaviors of parallel voltage-controlled Distributed Generation (DG) inverters not only relies on the stability of load sharing among them, but subjects to the interactions between the voltage control loops o...

  20. Quick-low-density parity check and dynamic threshold voltage optimization in 1X nm triple-level cell NAND flash memory with comprehensive analysis of endurance, retention-time, and temperature variation

    Science.gov (United States)

    Doi, Masafumi; Tokutomi, Tsukasa; Hachiya, Shogo; Kobayashi, Atsuro; Tanakamaru, Shuhei; Ning, Sheyang; Ogura Iwasaki, Tomoko; Takeuchi, Ken

    2016-08-01

    NAND flash memory’s reliability degrades with increasing endurance, retention-time and/or temperature. After a comprehensive evaluation of 1X nm triple-level cell (TLC) NAND flash, two highly reliable techniques are proposed. The first proposal, quick low-density parity check (Quick-LDPC), requires only one cell read in order to accurately estimate a bit-error rate (BER) that includes the effects of temperature, write and erase (W/E) cycles and retention-time. As a result, 83% read latency reduction is achieved compared to conventional AEP-LDPC. Also, W/E cycling is extended by 100% compared with conventional Bose-Chaudhuri-Hocquenghem (BCH) error-correcting code (ECC). The second proposal, dynamic threshold voltage optimization (DVO) has two parts, adaptive V Ref shift (AVS) and V TH space control (VSC). AVS reduces read error and latency by adaptively optimizing the reference voltage (V Ref) based on temperature, W/E cycles and retention-time. AVS stores the optimal V Ref’s in a table in order to enable one cell read. VSC further improves AVS by optimizing the voltage margins between V TH states. DVO reduces BER by 80%.

  1. 电力系统大扰动下暂态电压稳定的动态特征分析%Dynamic eigen analysis of transient voltage stability under large disturbance for power system

    Institute of Scientific and Technical Information of China (English)

    刘彦呈; 王川; 魏一

    2011-01-01

    A dynamic eigen analysis method is presented aiming at the defects that current voltage stability research results cannot give the explicit criterion about transient voltage stability information. First, this paper establishes an integrated mathematical model reflecting power system transient process with the consideration of speed-adjusting and excitation-control, i.e., Non-linear Differential Algebraic Equations (NDAE). Second, all the eigen values and left, right eigen vectors are solved by using implicit trapezoidal integration method to build Jacobian matrix dynamically in the process of step-by-step integration of NDAE. Finally, this paper calculates all the participating factors of eigen vectors corresponding with all status variables. Then, transient voltage instability criterion is proposed. Simulation results after comparing the method with time domain simulation demonstrate that the transient voltage instability criterion is correct. The paper provides a novel way to research power system transient voltage stability in terms of combining linear system theory with numerical integration.This work is supported by Natural Science Foundation of Liaoning Province (No. 20092148).%针对目前电力系统电压稳定性研究成果难以给出明确的暂态稳定判定信息的缺陷,提出一种电力系统大扰动下暂态电压稳定的动态特征分析方法.该方法首先建立反映电力系统暂态过渡过程的计及调速与励磁控制的综合数学模型,即非线性微分代数方程组(Non-linear Differential Algebraic Equations,NDAE);其次在运用隐式梯形积分法对NDAE进行逐步积分过程中动态生成Jacobian矩阵,并求解出全部特征根及左,右特征向量;最后计算出各个状态变量与之对应特征向量的相关因子,基于此给出暂态电压失稳的判据.该方法通过与时域仿真法的对比结果证明所提出系统暂态电压失稳判据的正确性,为今后从线性系统理论与数值积分

  2. Voltage Step Point Detection and Parameter Identification of General Dynamic Load Model%通用动态负荷模型电压阶跃检测和参数辨识方法

    Institute of Scientific and Technical Information of China (English)

    王立地; 何昕; 朴在林

    2014-01-01

    It is of significance for parameter identification of general dynamic load model to determine the position of equivalent step point in gradually-varying voltage signal and adopt reasonable signal preprocessing method. To meet the requirement of the dynamic load modeling experiment, the equivalent voltage step is adopted to take the place of gradually varied voltage signal, and the clustering analysis is led into the detection of equivalent voltage step point. Considering distribution characteristic of numerical value of voltage in a certain time interval and combining with wavelet denoising, the load signal is preprocessed;based on the platform of MATLAB and by means of development tool of graphics user interface (GUI) the parameter identification of general dynamic active load model is implemented. Experimental results show that, with the clustering method, the gradually-varying voltage step point can be effectively detected on the basis of the signal processed by average filtering and wavelet denoising;and utilizing the signal denoised by bior3.7 wavelet with the 4-th level decomposition for parameter identification, the obtained result is of the highest stability. The proposed method is suitable for load modeling with power recovery characteristic and off-line analysis under the condition of gradually-varied voltage due to manually changing the position of transformer tap and so on.%如何确定渐变电压信号等效阶跃点位置和采取合理的信号预处理方法对通用动态负荷模型参数辨识有重要影响。针对动态负荷建模试验的需要,利用等效电压阶跃来代替电压渐变信号,把聚类分析引入等效电压阶跃点检测中。在一定时间区间内考虑电压数值的分布特性,结合小波去噪进行负荷信号预处理,基于MATLAB平台,借助GUI(图形用户界面)开发手段,实现了通用动态有功负荷模型的参数辨识。实验结果表明:采用聚类分析方法,可以有效

  3. Wind Power Plant Voltage Stability Evaluation: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Muljadi, E.; Zhang, Y. C.

    2014-09-01

    Voltage stability refers to the ability of a power system to maintain steady voltages at all buses in the system after being subjected to a disturbance from a given initial operating condition. Voltage stability depends on a power system's ability to maintain and/or restore equilibrium between load demand and supply. Instability that may result occurs in the form of a progressive fall or rise of voltages of some buses. Possible outcomes of voltage instability are the loss of load in an area or tripped transmission lines and other elements by their protective systems, which may lead to cascading outages. The loss of synchronism of some generators may result from these outages or from operating conditions that violate a synchronous generator's field current limit, or in the case of variable speed wind turbine generator, the current limits of power switches. This paper investigates the impact of wind power plants on power system voltage stability by using synchrophasor measurements.

  4. A Novel Frequency Restoring Strategy of Hydro-PV Hybrid Microgrid

    DEFF Research Database (Denmark)

    Wei, Feng; Kai, Sun; Guan, Yajuan

    2014-01-01

    The conventional PV systems based on the voltage inverters only inject dispatched power to the utility grid when they work at a grid-connected mode in the hydro-PV hybrid microgrid. Due to the droop method employed for load sharing between generators, as well as the enormous inertia of system....... The existence of frequency steady-state error and the slow active power/frequency dynamic response are inevitable. Therefore, a novel frequency restoring strategy for the hydro-PV hybrid microgrid based on the improved hierarchical control of PV systems is proposed in this paper. The output active power of PV...

  5. Site Restoration

    Energy Technology Data Exchange (ETDEWEB)

    Noynaert, L.; Bruggeman, A.; Cornelissen, R.; Massaut, V.; Rahier, A

    2002-04-01

    The objectives, the programme, and the achievements of SCK-CEN's Site Restoration Department for 2001 are described. Main activities include the decommissioning of the BR3 PWR-reactor as well as other clean-up activities, projects on waste minimisation and the management of spent fuel and the flow of dismantled materials and the recycling of materials from decommissioning activities based on the smelting of metallic materials in specialised foundries. The department provides consultancy and services to external organisations and performs R and D on new techniques including processes for the treatment of various waste components including the reprocessing of spent fuel, the treatment of tritium, the treatment of liquid alkali metals into cabonates through oxidation, the treatment of radioactive organic waste and the reconditioning of bituminised waste products.

  6. Hysteresis in voltage-gated channels.

    Science.gov (United States)

    Villalba-Galea, Carlos A

    2016-09-30

    Ion channels constitute a superfamily of membrane proteins found in all living creatures. Their activity allows fast translocation of ions across the plasma membrane down the ion's transmembrane electrochemical gradient, resulting in a difference in electrical potential across the plasma membrane, known as the membrane potential. A group within this superfamily, namely voltage-gated channels, displays activity that is sensitive to the membrane potential. The activity of voltage-gated channels is controlled by the membrane potential, while the membrane potential is changed by these channels' activity. This interplay produces variations in the membrane potential that have evolved into electrical signals in many organisms. These signals are essential for numerous biological processes, including neuronal activity, insulin release, muscle contraction, fertilization and many others. In recent years, the activity of the voltage-gated channels has been observed not to follow a simple relationship with the membrane potential. Instead, it has been shown that the activity of voltage-gated channel displays hysteresis. In fact, a growing number of evidence have demonstrated that the voltage dependence of channel activity is dynamically modulated by activity itself. In spite of the great impact that this property can have on electrical signaling, hysteresis in voltage-gated channels is often overlooked. Addressing this issue, this review provides examples of voltage-gated ion channels displaying hysteretic behavior. Further, this review will discuss how Dynamic Voltage Dependence in voltage-gated channels can have a physiological role in electrical signaling. Furthermore, this review will elaborate on the current thoughts on the mechanism underlying hysteresis in voltage-gated channels.

  7. Technological Aspects: High Voltage

    CERN Document Server

    Faircloth, D C

    2013-01-01

    This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

  8. Piezoelectric Voltage Coupled Reentrant Cavity Resonator

    CERN Document Server

    Carvalho, Natalia C; Floch, Jean-Michel Le; Tobar, Michael Edmund

    2014-01-01

    A piezoelectric voltage coupled microwave reentrant cavity has been developed. The central cavity post is bonded to a piezoelectric actuator allowing the voltage control of small post displacements over a high dynamic range. We show that such a cavity can be implemented as a voltage tunable resonator, a transducer for exciting and measuring mechanical modes of the structure and a transducer for measuring comparative sensitivity of the piezoelectric material. Experiments were conducted at room and cryogenic temperatures with results verified using Finite Element software.

  9. Observation and investigation of a dynamic inflection point in current-voltage curves for roll-to-roll processed polymer photovoltaics

    DEFF Research Database (Denmark)

    Medford, Andrew James; Lilliedal, Mathilde Raad

    2010-01-01

    Inflection point behaviour is often observed in the current-voltage (IV) curve of polymer and organic solar cells. This phenomenon is examined in the context of flexible roll-to-roll (R2R) processed polymer solar cells in a large series of devices with a layer structure of: PET-ITO-ZnO-P3HT......:PCBM-PEDOT:PSS-Ag. The devices were manufactured using a combination of slot-die coating and screen printing; they were then encapsulated by lamination using a polymer based barrier material. All manufacturing steps were carried out in ambient air. The freshly prepared devices showed a consistent inflection point in the IV...

  10. Stray voltage mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Jamali, B.; Piercy, R.; Dick, P. [Kinetrics Inc., Toronto, ON (Canada). Transmission and Distribution Technologies

    2008-04-09

    This report discussed issues related to farm stray voltage and evaluated mitigation strategies and costs for limiting voltage to farms. A 3-phase, 3-wire system with no neutral ground was used throughout North America before the 1930s. Transformers were connected phase to phase without any electrical connection between the primary and secondary sides of the transformers. Distribution voltage levels were then increased and multi-grounded neutral wires were added. The earth now forms a parallel return path for the neutral current that allows part of the neutral current to flow continuously through the earth. The arrangement is responsible for causing stray voltage. Stray voltage causes uneven milk production, increased incidences of mastitis, and can create a reluctance to drink water amongst cows when stray voltages are present. Off-farm sources of stray voltage include phase unbalances, undersized neutral wire, and high resistance splices on the neutral wire. Mitigation strategies for reducing stray voltage include phase balancing; conversion from single to 3-phase; increasing distribution voltage levels, and changing pole configurations. 22 refs., 5 tabs., 13 figs.

  11. High voltage engineering

    CERN Document Server

    Rizk, Farouk AM

    2014-01-01

    Inspired by a new revival of worldwide interest in extra-high-voltage (EHV) and ultra-high-voltage (UHV) transmission, High Voltage Engineering merges the latest research with the extensive experience of the best in the field to deliver a comprehensive treatment of electrical insulation systems for the next generation of utility engineers and electric power professionals. The book offers extensive coverage of the physical basis of high-voltage engineering, from insulation stress and strength to lightning attachment and protection and beyond. Presenting information critical to the design, selec

  12. High voltage test techniques

    CERN Document Server

    Kind, Dieter

    2001-01-01

    The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

  13. Mitigation of Unbalanced Voltage Sags and Voltage Unbalance in CIGRE Low Voltage Distribution Network

    OpenAIRE

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar; Cecati, Carlo

    2013-01-01

    Any problem with voltage in a power network is undesirable as it aggravates the quality of the power. Power electronic devices such as Voltage Source Converter (VSC) based Static Synchronous Compensator (STATCOM) etc. can be used to mitigate the voltage problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate unbalanced voltage sags and voltage unbalance in the CIGRE Low Voltage (LV) test network and net-works like this. The voltage unbala...

  14. 基于黑板模型的配电网多故障分时段动态恢复%An Approach of Time Interval-Divided Multi-Fault Dynamic Restoration for Distribution Network Based on Blackboard Model

    Institute of Scientific and Technical Information of China (English)

    卢志刚; 叶治格; 杨丽君

    2012-01-01

    为更好地实现配电网抢修过程中多故障分时段的动态恢复问题,提出了基于黑板模型的配电网多故障分时段动态恢复方法.首先建立了以恢复失电电量最大与系统网损最小为目标的双层优化模型.然后根据黑板模型原理,每次故障恢复由一个工作代理负责,各代理进行分布式并行计算,并利用改进离散细菌群体趋药性算法求取各代理的最优解,协调机制通过对可中断负荷的控制保证重要负荷优先恢复和减少开关操作次数.算例结果验证了该方法的有效性.%To better implement the time interval-divided multi-fault dynamic restoration during the urgent repair of distribution network, based on the blackboard model a time interval-divided dynamic restoration approach for distribution network is given. Firstly, an algorithm that combines blackboard modules with improved discrete bacterial colony chemotaxis (DBCC) algorithm for time interval-divided dynamic multi-fault restoration of distribution network is proposed, and a double-layer optimization model, which takes the maximum restoration of lost load and minimum network loss as objectives, is built; then according to the principle of blackboard model each time of fault restoration is in charge by a working agent, meanwhile the distributed parallel calculation is performed for all agents and by use of improved DBCC algorithm the optimal solution of each agent is solved. By means of controlling the interruptible loads, the coordinative mechanism ensures preferential restoration of important loads and reduces the switching times of circuit breakers. Simulation results of modified IEEE 69-bus system show that the proposed approach is effective.

  15. The science and practice of river restoration

    Science.gov (United States)

    Wohl, Ellen; Lane, Stuart N.; Wilcox, Andrew C.

    2015-08-01

    River restoration is one of the most prominent areas of applied water-resources science. From an initial focus on enhancing fish habitat or river appearance, primarily through structural modification of channel form, restoration has expanded to incorporate a wide variety of management activities designed to enhance river process and form. Restoration is conducted on headwater streams, large lowland rivers, and entire river networks in urban, agricultural, and less intensively human-altered environments. We critically examine how contemporary practitioners approach river restoration and challenges for implementing restoration, which include clearly identified objectives, holistic understanding of rivers as ecosystems, and the role of restoration as a social process. We also examine challenges for scientific understanding in river restoration. These include: how physical complexity supports biogeochemical function, stream metabolism, and stream ecosystem productivity; characterizing response curves of different river components; understanding sediment dynamics; and increasing appreciation of the importance of incorporating climate change considerations and resiliency into restoration planning. Finally, we examine changes in river restoration within the past decade, such as increasing use of stream mitigation banking; development of new tools and technologies; different types of process-based restoration; growing recognition of the importance of biological-physical feedbacks in rivers; increasing expectations of water quality improvements from restoration; and more effective communication between practitioners and river scientists.

  16. Voltage verification unit

    Science.gov (United States)

    Martin, Edward J.

    2008-01-15

    A voltage verification unit and method for determining the absence of potentially dangerous potentials within a power supply enclosure without Mode 2 work is disclosed. With this device and method, a qualified worker, following a relatively simple protocol that involves a function test (hot, cold, hot) of the voltage verification unit before Lock Out/Tag Out and, and once the Lock Out/Tag Out is completed, testing or "trying" by simply reading a display on the voltage verification unit can be accomplished without exposure of the operator to the interior of the voltage supply enclosure. According to a preferred embodiment, the voltage verification unit includes test leads to allow diagnostics with other meters, without the necessity of accessing potentially dangerous bus bars or the like.

  17. Observation and investigation of a dynamic inflection point in current-voltage curves for roll-to-roll processed polymer photovoltaics

    DEFF Research Database (Denmark)

    Medford, Andrew James; Lilliedal, Mathilde Raad

    2010-01-01

    Inflection point behaviour is often observed in the current-voltage (IV) curve of polymer and organic solar cells. This phenomenon is examined in the context of flexible roll-to-roll (R2R) processed polymer solar cells in a large series of devices with a layer structure of: PET-ITO-ZnO-P3HT...... that the findings are applicable to various other device structures based on semiconducting oxides. The findings may have influences on the possibilities and scale-up of polymer solar technologies.......:PCBM-PEDOT:PSS-Ag. The devices were manufactured using a combination of slot-die coating and screen printing; they were then encapsulated by lamination using a polymer based barrier material. All manufacturing steps were carried out in ambient air. The freshly prepared devices showed a consistent inflection point in the IV...

  18. Dynamic voltage decoupling compensation control of distributed DC grid converter for permanent magnet wind generator%永磁风力发电机分布式直流并网动态电压解耦补偿控制

    Institute of Scientific and Technical Information of China (English)

    唐任远; 张洪阳; 张志锋; 朱建光

    2011-01-01

    In order to satisfy the demands of distributed DC grid with permanent magnet (synchronous)wind generator, the control strategy of distributed DC grid converter based on dynamic voltage compensation is proposed and studied with wide operation range. The control principle of excitation component was analyzed, and the basis was provided for high performances and so on. The disturbance variable was defined considering the cross coupling and voltage fluctuates based on the coordinate rotary system, and then the system was compensated. The DC chopper circuit was adopted with auxiliary support capacitance for the matching of diffirent DC voltage level. Fnially, the ariable speed constant voltage control of permanent magnet wind generator was implemented. Simulation and experimental vertify the teasibility and validity of the control stategies.%针对永磁(同步)风力发电机分布式直流并网的要求,提出并研究了一种基于机侧电压动态解耦补偿的且具有宽运行范围的分布式直流并网控制策略.分析了永磁风力发电机励磁分量控制原则,进而为电机的高性能运行提供依据.基于同步旋转坐标系把宽范围运行下系统所有的交叉耦合项和电压波动等原因造成的系统扰动统一定义为一个新的变量扰动,然后对控制系统进行补偿.采用辅助支撑电容的直流斩波电路进一步实现不同直流电压等级的匹配,最终实现永磁风力发电机的变速恒压控制.通过仿真和实验验证了控制策略的可行性和有效性.

  19. Combined Digital Electronic Current and Voltage Transducer

    Institute of Scientific and Technical Information of China (English)

    段雄英; 邹积岩; 等

    2002-01-01

    A high-performance current and voltage measurement system has been developed in power system.The system is composed of two parts:one current measurement element and one voltage measurement element.A Rogowski coil and a capacitive voltage divider are used respectively for the line current and voltage measurements.Active electronic components are used to modulate signal,and power supply for these components is drawn from power line via an auxiliary current transformer,Measurement signal is transmitted y optical fibers,which is resistant to electromagnetic induction and noise,With careful design and the use of digital signal processing technology,the whole system can meet 0.5% accuracy for metering and provides large dynamic range coupled with good accuracy for protective relaying use.

  20. Shame and Guilt in Restorative Justice

    DEFF Research Database (Denmark)

    Rodogno, Raffaele

    2008-01-01

    in particular, having presented the aims of restorative justice, the importance of face-to-face conferences in reaching these aims, the emotional dynamics that take place within such conferences, and the relevant parts of the empirical psychology of shame and guilt, I argue that restorative justice......In this article, I examine the relevance and desirability of shame and guilt to restorative justice conferences. I argue that a careful study of the psychology of shame and guilt reveals that both emotions possess traits that can be desirable and traits that can be undesirable for restoration. More...... practitioners have to take account of a rather more complex picture than it had hitherto been thought. Restorative conferences are not simply about "shame management," though practitioners must certainly avoid shaming and humiliation. Given the nature of shame, guilt, and restorative conferences...

  1. 一种基于动态阈值NMOS的1.2V CMOS模拟乘法器%A 1.2 V CMOS Analog Multiplier Based on Dynamic Threshold Voltage NMOS Transistor

    Institute of Scientific and Technical Information of China (English)

    程卫东; 朱樟明; 王雷

    2011-01-01

    分析了以动态阈值NMOS晶体管作为输入信号的输入晶体管,利用4个动态阈值NMOS和2个有源电阻设计和实现的一种1.2 V低功耗CMOS模拟乘法器电路。该电路具有节省输入晶体管数目、偏置晶体管和偏置电路,以及性能指标优良的特点。其主要参数指标达到:一、三次谐波差值40 dB,输出信号频带宽度375 MHz,平均电源电流约30μA,动态功耗约36μW。可直接应用于低功耗通信集成电路设计。%This paper analyses an analog multiplier based on dynamic threshold voltage NMOS transistor for two input transistor.Four dynamic threshold voltage NMOS transistor and two active resistors are used to design a novel 1.2 V low power CMOS analog multiplier.The number of input transistor has been decreased and the biased transistor and circuits have been saved,while the performance is appropriate.The main characteristics are that the margin between the first order harmonious wave and the third order harmonious wave of the output wave is about 40 dB,that the output frequency bandwidth is 375 MHz,and that the average power supply current is 30 μA.The novel analog multiplier can be applied for the design of low power communication integrated circuits.

  2. High Voltage Distribution

    Science.gov (United States)

    Norbeck, Edwin; Miller, Michael; Onel, Yasar

    2010-11-01

    For detector arrays that require 5 to 10 kV at a few microamps each for hundreds of detectors, using hundreds of HV power supplies is unreasonable. Bundles of hundreds of HV cables take up space that should be filled with detectors. A typical HV module can supply 1 ma, enough current for hundreds of detectors. It is better to use a single HV module and distribute the current as needed. We show a circuit that, for each detector, measures the current, cuts off the voltage if the current exceeds a set maximum, and allows the HV to be turned on or off from a control computer. The entire array requires a single HV cable and 2 or 3 control lines. This design provides the same voltage to all of the detectors, the voltage set by the single HV module. Some additional circuitry would allow a computer controlled voltage drop between the HV and each individual detector.

  3. High voltage engineering fundamentals

    CERN Document Server

    Kuffel, E; Hammond, P

    1984-01-01

    Provides a comprehensive treatment of high voltage engineering fundamentals at the introductory and intermediate levels. It covers: techniques used for generation and measurement of high direct, alternating and surge voltages for general application in industrial testing and selected special examples found in basic research; analytical and numerical calculation of electrostatic fields in simple practical insulation system; basic ionisation and decay processes in gases and breakdown mechanisms of gaseous, liquid and solid dielectrics; partial discharges and modern discharge detectors; and over

  4. Optimization of a load shedding scheme using dynamic voltage stability linearized index based on PMU%基于PMU的电压稳定动态线性化指标优化切负荷算法

    Institute of Scientific and Technical Information of China (English)

    丁涛; 董柏峰; 顾伟; 万秋兰

    2013-01-01

      紧急状况下,优化包含动态负荷的系统切负荷量,以保证系统电压快速恢复正常状态是系统安全的关键。利用PMU测量信息推导了电压稳定动态线性化指标的灵敏度,将其作为实施切负荷的作用因子。建立了以切负荷量最小为目标函数和电压指标偏差量为约束条件的切负荷优化模型。首次实现了分区多步切负荷的算法,在实时计算得到的动态电压稳定指标超标基础上,利用所提出的优化模型实施多步动态优化切负荷,并实时修正作用因子的灵敏度,克服了传统一步欠切或过切的缺点。用IEEE14节点测试系统和国内实际电网算例证实了该方法的可行性和有效性。%It is critical to guarantee the system’s security as quickly as possible by optimizing the shedding load including dynamic components under contingencies. Dynamic voltage stability linearized index sensitivity for dynamic load model is derived based on PMU for the role of the implementation of load shedding factor;the optimization model of load shedding has been established with the objective function of a minimum of load shedding and the constraint of the voltage indicator deviation. The distributed multi-step load shedding algorithm is firstly achieved according to the dynamic order of the index-exceeding node, and the sensitivity of linearized index is corrected at each step, which overcomes the over-shedding or under-shedding problem in traditional methods. Examples of IEEE 14-bus tested system and real grid system demonstrate the feasibility and effectiveness of this method. This work is supported by National Natural Science Foundation of China (No. 50907008 and No. 60974036).

  5. Predicting bed shear stress and its role in sediment dynamics and restoration potential of the Everglades and other vegetated flow systems

    Science.gov (United States)

    Larsen, Laurel G.; Harvey, Judson; John P. Crimaldi,

    2009-01-01

    Entrainment of sediment by flowing water affects topography, habitat suitability, and nutrient cycling in vegetated floodplains and wetlands, impacting ecosystem evolution and the success of restoration projects. Nonetheless, restoration managers lack simple decision-support tools for predicting shear stresses and sediment redistribution potential in different vegetation communities. Using a field-validated numerical model, we developed state-space diagrams that provide these predictions over a range of water-surface slopes, depths, and associated velocities in Everglades ridge and slough vegetation communities. Diminished bed shear stresses and a consequent decrease in bed sediment redistribution are hypothesized causes of a recent reduction in the topographic and vegetation heterogeneity of this ecosystem. Results confirmed the inability of present-day flows to entrain bed sediment. Further, our diagrams showed bed shear stresses to be highly sensitive to emergent vegetation density and water-surface slope but less sensitive to water depth and periphyton or floating vegetation abundance. These findings suggested that instituting a pulsing flow regime could be the most effective means to restore sediment redistribution to the Everglades. However, pulsing flows will not be sufficient to erode sediment from sloughs with abundant spikerush, unless spikerush density first decreases by natural or managed processes. Our methods provide a novel tool for identifying restoration parameters and performance measures in many types of vegetated aquatic environments where sediment erosion and deposition are involved.

  6. Predicting bed shear stress and its role in sediment dynamics and restoration potential of the Everglades and other vegetated flow systems

    Science.gov (United States)

    Larsen, Laurel G.; Harvey, Judson; John P. Crimaldi,

    2009-01-01

    Entrainment of sediment by flowing water affects topography, habitat suitability, and nutrient cycling in vegetated floodplains and wetlands, impacting ecosystem evolution and the success of restoration projects. Nonetheless, restoration managers lack simple decision-support tools for predicting shear stresses and sediment redistribution potential in different vegetation communities. Using a field-validated numerical model, we developed state-space diagrams that provide these predictions over a range of water-surface slopes, depths, and associated velocities in Everglades ridge and slough vegetation communities. Diminished bed shear stresses and a consequent decrease in bed sediment redistribution are hypothesized causes of a recent reduction in the topographic and vegetation heterogeneity of this ecosystem. Results confirmed the inability of present-day flows to entrain bed sediment. Further, our diagrams showed bed shear stresses to be highly sensitive to emergent vegetation density and water-surface slope but less sensitive to water depth and periphyton or floating vegetation abundance. These findings suggested that instituting a pulsing flow regime could be the most effective means to restore sediment redistribution to the Everglades. However, pulsing flows will not be sufficient to erode sediment from sloughs with abundant spikerush, unless spikerush density first decreases by natural or managed processes. Our methods provide a novel tool for identifying restoration parameters and performance measures in many types of vegetated aquatic environments where sediment erosion and deposition are involved.

  7. Restoration in multi-domain GMPLS-based networks

    DEFF Research Database (Denmark)

    Manolova, Anna; Ruepp, Sarah Renée; Dittmann, Lars

    2011-01-01

    In this paper, we evaluate the efficiency of using restoration mechanisms in a dynamic multi-domain GMPLS network. Major challenges and solutions are introduced and two well-known restoration schemes (End-to-End and Local-to-End) are evaluated. Additionally, new restoration mechanisms are introdu......, resource overbuild or recovery delay...

  8. Disrupted dynamics of F-actin and insulin granule fusion in INS-1 832/13 beta-cells exposed to glucotoxicity: partial restoration by glucagon-like peptide 1.

    Science.gov (United States)

    Quinault, Aurore; Gausseres, Blandine; Bailbe, Danielle; Chebbah, Nella; Portha, Bernard; Movassat, Jamileh; Tourrel-Cuzin, Cecile

    2016-08-01

    Actin dynamics in pancreatic β-cells is involved in insulin exocytosis but the molecular mechanisms of this dynamics and its role in biphasic insulin secretion in pancreatic β-cells is largely unknown. Moreover, the impact of a glucotoxic environment on the sub-cortical actin network dynamics is poorly studied. In this study, we investigate the behavior of insulin granules and the subcortical actin network dynamics in INS-1 832/13 β-cells submitted to a normal or glucotoxic environment. Our results show that glucose stimulation leads to a reorganization of the subcortical actin network with a rupture of its interactions with t-SNARE proteins (Syntaxin 1A and SNAP-25), promoting insulin secretion in INS-1 832/13 β-cells. Prolonged exposure of INS-1 832/13 β-cells to high-glucose levels (glucotoxicity) leads to the densification of the cortical actin network, which prevents its reorganization under acute glucose, and diminishes the glucose-stimulated insulin secretion, as shown by the decreased number of fusion events. The most interesting in our results is the partial restoration by GLP-1 of the insulin secretion ability from high-glucose treated INS-1 832/13 cells. This improved insulin exocytosis is associated with partial restored actin dynamics and fusion events during the two phases of the secretion, with a preferential involvement of Epac2 signaling in the first phase and a rather involvement of PKA signaling in the second phase of insulin exocytosis. All these data provide some new insights into the mechanism by which current therapeutics may be improving insulin secretion.

  9. Device for monitoring cell voltage

    Science.gov (United States)

    Doepke, Matthias [Garbsen, DE; Eisermann, Henning [Edermissen, DE

    2012-08-21

    A device for monitoring a rechargeable battery having a number of electrically connected cells includes at least one current interruption switch for interrupting current flowing through at least one associated cell and a plurality of monitoring units for detecting cell voltage. Each monitoring unit is associated with a single cell and includes a reference voltage unit for producing a defined reference threshold voltage and a voltage comparison unit for comparing the reference threshold voltage with a partial cell voltage of the associated cell. The reference voltage unit is electrically supplied from the cell voltage of the associated cell. The voltage comparison unit is coupled to the at least one current interruption switch for interrupting the current of at least the current flowing through the associated cell, with a defined minimum difference between the reference threshold voltage and the partial cell voltage.

  10. High voltage pulse generator

    Science.gov (United States)

    Fasching, George E.

    1977-03-08

    An improved high-voltage pulse generator has been provided which is especially useful in ultrasonic testing of rock core samples. An N number of capacitors are charged in parallel to V volts and at the proper instance are coupled in series to produce a high-voltage pulse of N times V volts. Rapid switching of the capacitors from the paralleled charging configuration to the series discharging configuration is accomplished by using silicon-controlled rectifiers which are chain self-triggered following the initial triggering of a first one of the rectifiers connected between the first and second of the plurality of charging capacitors. A timing and triggering circuit is provided to properly synchronize triggering pulses to the first SCR at a time when the charging voltage is not being applied to the parallel-connected charging capacitors. Alternate circuits are provided for controlling the application of the charging voltage from a charging circuit to be applied to the parallel capacitors which provides a selection of at least two different intervals in which the charging voltage is turned "off" to allow the SCR's connecting the capacitors in series to turn "off" before recharging begins. The high-voltage pulse-generating circuit including the N capacitors and corresponding SCR's which connect the capacitors in series when triggered "on" further includes diodes and series-connected inductors between the parallel-connected charging capacitors which allow sufficiently fast charging of the capacitors for a high pulse repetition rate and yet allow considerable control of the decay time of the high-voltage pulses from the pulse-generating circuit.

  11. 跨越式高压输电线路巡线机器人动力学研究%Leaping high-voltage transmission line inspection robot dynamics study

    Institute of Scientific and Technical Information of China (English)

    王婷; 吴功平

    2015-01-01

    The structure character of leaping high voltage transmission line inspection robot is analysed and inspection robot spatial coordinates is built with the DH method, and then the dynamic model of the robot manipulator is establishedon the basis of Lagrange principle.The dynamics simulation and experiment study of one type posture of the manipulatorjoints are accomplished, the force or torque of joints is confirmed after presetting displacement curve and speed curve and theoretical foundation is prepared for the real-time control of robot.%分析了跨越式高压输电线路巡线作业机器人的结构特征,采用D-H法构建巡线机器人空间坐标,用Lagrange方法建立了机器人机械臂的动力学模型。基于此动力学模型,对一种典型工况进行了机械臂各关节动力学逆问题仿真,通过给定已知运动轨迹对应的各关节位移、速度曲线,确定所需的关节力矩或关节力,为机器人的实时控制提供理论依据。

  12. Dynamics of leaf litter humidity, depth and quantity: two restoration strategies failed to mimic ground microhabitat conditions of a low montane and premontane forest in Costa Rica.

    Science.gov (United States)

    Barrientos, Zaidett

    2012-09-01

    Little is known about how restoration strategies affect aspects like leaf litter's quantity, depth and humidity. I analyzed leaf litter's quantity, depth and humidity yearly patterns in a primary tropical lower montane wet forest and two restored areas: a 15 year old secondary forest (unassisted restoration) and a 40 year old Cupressus lusitanica plantation (natural understory). The three habitats are located in the Rio Macho Forest Reserve, Costa Rica. Twenty litter samples were taken every three months (April 2009-April 2010) in each habitat; humidity was measured in 439g samples (average), depth and quantity were measured in five points inside 50x50cm plots. None of the restoration strategies reproduced the primary forest leaf litter humidity, depth and quantity yearly patterns. Primary forest leaf litter humidity was higher and more stable (mean=73.2), followed by secondary forest (mean=63.3) and cypress plantation (mean=52.9) (Kruskall-Wallis=77.93, n=232, p=0.00). In the primary (Kruskal-Wallis=31.63, n=78, p<0.001) and secondary (Kruskal-Wallis=11.79, n=75, p=0.008) forest litter accumulation was higher during April due to strong winds. In the primary forest (Kruskal-wallis=21.83, n=78, p<0.001) and the cypress plantation (Kruskal-wallis=39.99, n=80, p<0.001) leaf litter depth was shallow in October because heavy rains compacted it. Depth patterns were different from quantity patterns and described the leaf litter's structure in different ecosystems though the year. September 01.

  13. Governing Forest Landscape Restoration: Cases from Indonesia

    Directory of Open Access Journals (Sweden)

    Cora van Oosten

    2014-05-01

    Full Text Available Forest landscape restoration includes both the planning and implementation of measures to restore degraded forests within the perspective of the wider landscape. Governing forest landscape restoration requires fundamental considerations about the conceptualisation of forested landscapes and the types of restoration measures to be taken, and about who should be engaged in the governance process. A variety of governance approaches to forest landscape restoration exist, differing in both the nature of the object to be governed and the mode of governance. This paper analyses the nature and governance of restoration in three cases of forest landscape restoration in Indonesia. In each of these cases, both the original aim for restoration and the initiators of the process differ. The cases also differ in how deeply embedded they are in formal spatial planning mechanisms at the various political scales. Nonetheless, the cases show similar trends. All cases show a dynamic process of mobilising the landscape’s stakeholders, plus a flexible process of crafting institutional space for conflict management, negotiation and decision making at the landscape level. As a result, the landscape focus changed over time from reserved forests to forested mosaic lands. The cases illustrate that the governance of forest landscape restoration should not be based on strict design criteria, but rather on a flexible governance approach that stimulates the creation of novel public-private institutional arrangements at the landscape level.

  14. 负荷模型选择对动态无功需求和暂态电压稳定的影响%Impact on Dynamic Reactive Power Demand and Transient Voltage Stability by Load Model Selection

    Institute of Scientific and Technical Information of China (English)

    张一荻; 管霖

    2014-01-01

    电力系统中的电源规划和静态无功补偿规划已经形成了相对成熟的理论和方法,但对于动态无功补偿的规划研究则尚未起步。利用 PSCAD/EMTDC软件,从动态无功需求分析和补偿容量选择原则两个方面进行仿真分析,研究感应电动机动态无功负荷的需求特性;给定负荷水平下不同的负荷模型和参数对负荷动态无功需求的影响;电网强弱和负荷模型对母线暂态电压稳定的影响。验证了依据动态无功需求测算来配置动态无功补偿装置补偿容量的可行性,并提出相应的规划方法。%There are comparatively mature theories and methods for power source planning and static var compensation plan-ning in power system but planning for dynamic reactive power compensation has not started up. By using PSCAD/EMTDC software and in aspects of analysis on dynamic reactive power demand and selection principle of compensation capacity,sim-ulation analysis was conducted for studying demand characteristics of dynamic reactive power load of the motor,impact on load dynamic reactive power demand by different load models and parameters with given load level and impact on transient voltage stability of the bus by strongness and weakness of the power grid and load models. Feasibility of deploying dynamic reactive power compensation device according to dynamic reactive power demand was verified and relevant planning methods were proposed.

  15. Energy-aware Supply Voltage and Body Biasing Voltage Scheduling Algorithm for Real-time Distributed Systems

    Institute of Scientific and Technical Information of China (English)

    SUYajuan; WEIShaojun

    2005-01-01

    Technique of energy minimization by combining Dynamic voltage scheduling (DVS) and Adaptive body biasing voltage (ABB) method for distributed realtime system at design level is proposed. First, a simplified energy optimizing model is illustrated where the supply voltage or body biasing voltage is kept as constant according to each separated frequency region, thus calculation of exceeding equation is avoided. Divergence of simplified and analytic model within 5% indicates the accuracy of this model. Based on it, the proposed approach named LEVVS (Low energy supply voltage and body biasing voltage scheduling algorithm) explores space of minimizing energy consumption by finding optimal trade-off between dynamic and static energy. The corresponding optimal supply voltage and body biasing voltage are determined by an iterative method in which the supply voltage and body biasing voltage of tasks are adjusted according to the value of energy latency differential coefficient of each task and slack time distribution of the system. Experiments show that using LEVVS approach, 51% more average energy reduction can be obtained than employing DVS method alone. Furthermore the effects of switch capacitance and global slack on the energy saving efficiency of LEVVS are investigated. The smaller the global slack or average switch capacitance is, the more the energy saving of LEVVS compared with DVS is.

  16. The Control Unit of a Single Phase Voltage Regulator

    CERN Document Server

    Colak, Ilknur

    2010-01-01

    Supplying regulated voltage to critical loads is an important topic for several years. This paper presents a single-phase electronic voltage regulator based on high frequency switching of an isolated transformer where primary side voltage is controlled by two full-bridge converters sharing a common DC bus and operating at 50Hz and 20kHz switching frequencies. This allows 50Hz induced voltage on the primary side of the transformer, regulated by high frequency switching. Depending on the input voltage, voltage at the secondary side of the transformer add to (boost mode) or subtract (buck mode) from the supply voltage, therefore, maintaining a regulated voltage value across the load. The regulator is controlled by a digital controller allowing fast dynamic response. A 5kVA single-phase voltage regulator is realized to verify the operation of the proposed algorithm. The experimental results show that regulator maintains constant voltage across the load both in step-up (low supply voltage) and step-down (high supp...

  17. Dynamic Voltage-Frequency and Workload Joint Scaling Power Management for Energy Harvesting Multi-Core WSN Node SoC

    Science.gov (United States)

    Li, Xiangyu; Xie, Nijie; Tian, Xinyue

    2017-01-01

    This paper proposes a scheduling and power management solution for energy harvesting heterogeneous multi-core WSN node SoC such that the system continues to operate perennially and uses the harvested energy efficiently. The solution consists of a heterogeneous multi-core system oriented task scheduling algorithm and a low-complexity dynamic workload scaling and configuration optimization algorithm suitable for light-weight platforms. Moreover, considering the power consumption of most WSN applications have the characteristic of data dependent behavior, we introduce branches handling mechanism into the solution as well. The experimental result shows that the proposed algorithm can operate in real-time on a lightweight embedded processor (MSP430), and that it can make a system do more valuable works and make more than 99.9% use of the power budget. PMID:28208730

  18. Dynamic Voltage-Frequency and Workload Joint Scaling Power Management for Energy Harvesting Multi-Core WSN Node SoC

    Directory of Open Access Journals (Sweden)

    Xiangyu Li

    2017-02-01

    Full Text Available This paper proposes a scheduling and power management solution for energy harvesting heterogeneous multi-core WSN node SoC such that the system continues to operate perennially and uses the harvested energy efficiently. The solution consists of a heterogeneous multi-core system oriented task scheduling algorithm and a low-complexity dynamic workload scaling and configuration optimization algorithm suitable for light-weight platforms. Moreover, considering the power consumption of most WSN applications have the characteristic of data dependent behavior, we introduce branches handling mechanism into the solution as well. The experimental result shows that the proposed algorithm can operate in real-time on a lightweight embedded processor (MSP430, and that it can make a system do more valuable works and make more than 99.9% use of the power budget.

  19. Dynamic Voltage-Frequency and Workload Joint Scaling Power Management for Energy Harvesting Multi-Core WSN Node SoC.

    Science.gov (United States)

    Li, Xiangyu; Xie, Nijie; Tian, Xinyue

    2017-02-08

    This paper proposes a scheduling and power management solution for energy harvesting heterogeneous multi-core WSN node SoC such that the system continues to operate perennially and uses the harvested energy efficiently. The solution consists of a heterogeneous multi-core system oriented task scheduling algorithm and a low-complexity dynamic workload scaling and configuration optimization algorithm suitable for light-weight platforms. Moreover, considering the power consumption of most WSN applications have the characteristic of data dependent behavior, we introduce branches handling mechanism into the solution as well. The experimental result shows that the proposed algorithm can operate in real-time on a lightweight embedded processor (MSP430), and that it can make a system do more valuable works and make more than 99.9% use of the power budget.

  20. Voltage Regulators for Photovoltaic Systems

    Science.gov (United States)

    Delombard, R.

    1986-01-01

    Two simple circuits developed to provide voltage regulation for highvoltage (i.e., is greater than 75 volts) and low-voltage (i.e., is less than 36 volts) photovoltaic/battery power systems. Use of these circuits results in voltage regulator small, low-cost, and reliable, with very low power dissipation. Simple oscillator circuit controls photovoltaic-array current to regulate system voltage and control battery charging. Circuit senses battery (and system) voltage and adjusts array current to keep battery voltage from exceeding maximum voltage.

  1. Studying Voltage Transformer Ferroresonance

    Directory of Open Access Journals (Sweden)

    Hamid Radmanesh

    2012-09-01

    Full Text Available This study studies the effect of Circuit Breaker Shunt Resistance (CBSR, Metal Oxide Vaistor (MOV and Neutral earth Resistance (NR on the control of ferroresonance in the voltage transformer. It is expected that NR can controlled ferroresonance better than MOV and CBSR. Study has been done on a one phase voltage transformer rated 100 VA, 275 kV. The simulation results reveal that considering the CBSR and MOV exhibits a great mitigating effect on ferroresonance overvoltages, but these resistances cannot control these phenomena for all range of parameters. By applying NR to the system structure, ferroresonance has been controlled and its amplitude has been damped for all parameters values.

  2. Dynamic Simulation of Induction Motor Fed by SVPWM Voltage Source Inverter%SVPWM电压源逆变器供电异步电动机的动态仿真

    Institute of Scientific and Technical Information of China (English)

    张贻旭; 谢卫; 屈鲁; 卢颖娟

    2012-01-01

    The dynamic model of three-phase induction motor is established in the d-q coordinate. Sinusoidal pulse width modulation (SPWM) technique and space vector pulse width modulation (SVPWM) technique which used to control induction motor are introduced. Dynamic simulation model of three - phase induction motor fed by SPWM and SVPWM voltage source inverter are established respectively, and the simulation results under these two control techniques are comparatively analyzed. The simulation results demonstrate that SVPWM induction motor drive system can start faster, the torque ripple is smaller and the stator current harmonics is smaller compared with SPWM control. The system has good steady and dynamic performance.%建立了三相异步电动机在d-q坐标系下的动态数学模型,并介绍了控制异步电动机运行的两种控制技术:正弦波脉宽调制(SPWM)技术和空间电压矢量脉宽调制(SVPWM)技术。在Matlab/Simulink环境下,分别建立SPWM和SVPWM电压源型逆变器供电的三相异步电动机的动态仿真模型,比较分析了在这两种控制方式下的仿真结果。结果表明,较之SPWM控制方式,SVPWM的异步电动机变频调速系统启动快,转矩脉动小,定子电流谐波小,具有较好的动态性能和稳态性能。

  3. Insulation co-ordination in high-voltage electric power systems

    CERN Document Server

    Diesendorf, W

    2015-01-01

    Insulation Co-ordination in High-Voltage Electric Power Systems deals with the methods of insulation needed in different circumstances. The book covers topics such as overvoltages and lightning surges; disruptive discharge and withstand voltages; self-restoring and non-self-restoring insulation; lightning overvoltages on transmission lines; and the attenuation and distortion of lightning surges. Also covered in the book are topics such as the switching surge designs of transmission lines, as well as the insulation coordination of high-voltage stations. The text is recommended for electrical en

  4. [Progress and prospects on evaluation of ecological restoration: a review of the 5th World Conference on Ecological Restoration].

    Science.gov (United States)

    Ding, Jing-Yi; Zhao, Wen-Wu

    2014-09-01

    The 5th World Conference on Ecological Restoration was held in Madison, Wisconsin, USA on October 6-11, 2013. About 1200 delegates from more than 50 countries attended the conference, and discussed the latest developments in different thematic areas of ecological restoration. Discussions on evaluation of ecological restoration were mainly from three aspects: The construction for evaluation indicator system of ecological restoration; the evaluation methods of ecological restoration; monitoring and dynamic evaluation of ecological restoration. The meeting stressed the importance of evaluation in the process of ecological restoration and concerned the challenges in evaluation of ecological restoration. The conference had the following enlightenments for China' s research on evaluation of ecological restoration: 1) Strengthening the construction of comprehensive evaluation indicators system and focusing on the multi-participation in the evaluation process. 2) Paying more attentions on scale effect and scale transformation in the evaluation process of ecological restoration. 3) Expanding the application of 3S technology in assessing the success of ecological restoration and promoting the dynamic monitoring of ecological restoration. 4) Carrying out international exchanges and cooperation actively, and promoting China's international influence in ecological restoration research.

  5. Restorative dentistry for children.

    Science.gov (United States)

    Donly, Kevin J

    2013-01-01

    This article discusses contemporary pediatric restorative dentistry. Indications and contraindications for the choice of different restorative materials in different clinical situations, including the risk assessment of the patient, are presented. The specific use of glass ionomer cement or resin-modified glass ionomer cement, resin-based composite, and stainless steel crowns is discussed so that preparation design and restoration placement is understood.

  6. Global Ecosystem Restoration Index

    DEFF Research Database (Denmark)

    Fernandez, Miguel; Garcia, Monica; Fernandez, Nestor

    2015-01-01

    The Global ecosystem restoration index (GERI) is a composite index that integrates structural and functional aspects of the ecosystem restoration process. These elements are evaluated through a window that looks into a baseline for degraded ecosystems with the objective to assess restoration...

  7. VOLTAGE REGULATORS ASYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available A promising is currently the use of asynchronous generators with capacitive excitation as a source of electricity in stand-alone power systems. Drive asynchronous generators may exercise as a thermal engine and wind wheel wind power plant or turbines of small hydropower plants. The article discusses the structural and schematics of voltage stabilizers and frequency of asynchronous generators with improved operational and technical specifications. Technical novelty of design solutions of the magnetic system and stabilizers asynchronous generator of electricity parameters confirmed by the patents for the invention of the Russian Federation. The proposed technical solution voltage stabilizer asynchronous generators, can reduce the weight of the block capacitors excitation and reactive power compensation, as well as to simplify the control system power circuit which has less power electronic devices. For wind power plants it is an important issue not only to stabilize the voltage of the generator, but also the frequency of the current. Recommend functionality stabilizer schemes parameters of electric power made for direct frequency converters with artificial and natural switching power electronic devices. It is also proposed as part of stabilization systems use single-phase voltage, three-phase transformers with rotating magnetic field, reduce the level of electromagnetic interference generated by power electronic devices for switching, enhance the efficiency and reliability of the stabilizer.

  8. Geomagnetism and Induced Voltage

    Science.gov (United States)

    Abdul-Razzaq, W.; Biller, R. D.

    2010-01-01

    Introductory physics laboratories have seen an influx of "conceptual integrated science" over time in their classrooms with elements of other sciences such as chemistry, biology, Earth science, and astronomy. We describe a laboratory to introduce this development, as it attracts attention to the voltage induced in the human brain as it…

  9. High-voltage picoamperemeter

    Energy Technology Data Exchange (ETDEWEB)

    Bugl, Andrea; Ball, Markus; Boehmer, Michael; Doerheim, Sverre; Hoenle, Andreas; Konorov, Igor [Technische Universitaet Muenchen, Garching (Germany); Ketzer, Bernhard [Technische Universitaet Muenchen, Garching (Germany); Helmholtz-Institut fuer Strahlen- und Kernphysik, Bonn (Germany)

    2014-07-01

    Current measurements in the nano- and picoampere region on high voltage are an important tool to understand charge transfer processes in micropattern gas detectors like the Gas Electron Multiplier (GEM). They are currently used to e.g. optimize the field configuration in a multi-GEM stack to be used in the ALICE TPC after the upgrade of the experiment during the 2nd long shutdown of the LHC. Devices which allow measurements down to 1pA at high voltage up to 6 kV have been developed at TU Muenchen. They are based on analog current measurements via the voltage drop over a switchable shunt. A microcontroller collects 128 digital ADC values and calculates their mean and standard deviation. This information is sent with a wireless transmitting unit to a computer and stored in a root file. A nearly unlimited number of devices can be operated simultaneously and read out by a single receiver. The results can also be displayed on a LCD directly at the device. Battery operation and the wireless readout are important to protect the user from any contact to high voltage. The principle of the device is explained, and systematic studies of their properties are shown.

  10. Voltage-induced reduction of graphene oxide

    Science.gov (United States)

    Faucett, Austin C.

    Graphene Oxide (GO) is being widely researched as a precursor for the mass production of graphene, and as a versatile material in its own right for flexible electronics, chemical sensors, and energy harvesting applications. Reduction of GO, an electrically insulating material, into reduced graphene oxide (rGO) restores electrical conductivity via removal of oxygen-containing functional groups. Here, a reduction method using an applied electrical bias, known as voltage-induced reduction, is explored. Voltage-induced reduction can be performed under ambient conditions and avoids the use of hazardous chemicals or high temperatures common with standard methods, but little is known about the reduction mechanisms and the quality of rGO produced with this method. This work performs extensive structural and electrical characterization of voltage-reduced GO (V-rGO) and shows that it is competitive with standard methods. Beyond its potential use as a facile and eco-friendly processing approach, V-rGO reduction also offers record high-resolution patterning capabilities. In this work, the spatial resolution limits of voltage-induced reduction, performed using a conductive atomic force microscope probe, are explored. It is shown that arbitrary V-rGO conductive features can be patterned into insulating GO with nanoscale resolution. The localization of voltage-induced reduction to length scales < 10 nm allows studies of reduction reaction kinetics, using electrical current obtained in-situ, with statistical robustness. Methods for patterning V-rGO nanoribbons are then developed. After presenting sub-10nm patterning of V-rGO nanoribbons in GO single sheets and films, the performance of V-rGO nanoribbon field effect transistors (FETs) are demonstrated. Preliminary measurements show an increase in electrical current on/off ratios as compared to large-area rGO FETs, indicating transport gap modulation that is possibly due to quantum confinement effects.

  11. Restoring the incisal edge.

    Science.gov (United States)

    Terry, Douglas A

    2005-01-01

    Restorative dentistry evolves with each development of new material and innovative technique. Selection of improved restorative materials that simulate the physical properties and other characteristics of natural teeth, in combination with restorative techniques such as the proximal adaptation and incremental layering, provide the framework that ensures the optimal development of an esthetic restoration. These advanced placement techniques offer benefits such as enhanced chromatic integration, polychromatism, ideal anatomical form and function, optimal proximal contact, improved marginal integrity and longer lasting directly placed composite restorations. The purpose of this article is to give the reader a better understanding of the complex restorative challenge in achieving true harmonization of the primary parameters in esthetics (that is, color, shape and texture) represented by the replacement of a single anterior tooth. The case presented demonstrates the restoration of a Class IV fracture integrating basic adhesive principles with these placement techniques and a recently developed nanoparticle hybrid composite resin system (Premise, Kerr/Sybron, Orange, CA). The clinical presentation describes preoperative considerations, tooth preparation, development of the body layer, internal characterization with tints, development of the artificial enamel layer, shaping and contouring, and polishing of a Class IV composite restoration. The clinical significance is that anterior tooth fractures can be predictably restored using contemporary small particle hybrid composite resin systems with the aforementioned restorative techniques. These placement techniques when used with proper attention to preparation design, adhesive protocol and finishing and polishing procedures, allow the clinician to successfully restore form, function and esthetics to the single anterior tooth replacement.

  12. 动态电压调节开关变换器的定频导通时间控制%Constant frequency turn-on time control of dynamic voltage scaling switching converters

    Institute of Scientific and Technical Information of China (English)

    徐杨军; 许建平; 王金平; 何圣仲

    2014-01-01

    对动态电压调节(Dynamic Voltage Scaling,DVS)开关变换器的定频导通时间(Constant Frequency Turn-On Time,CFOT)控制技术进行了研究,在恒定导通时间(Constant On-Time,COT)基础上,通过引入输入电压前馈和输出参考电压反馈环路,实现不同输入、输出电压条件下DVS开关变换器保持开关频率恒定.研究结果表明,CFOT控制不仅继承了传统COT控制环路设计简单、无需误差放大器及其相应的补偿网路、瞬态响应快的优点,而且消除了输入、输出电压变动对开关频率的影响.

  13. Voltage scheduling for low power/energy

    Science.gov (United States)

    Manzak, Ali

    2001-07-01

    Power considerations have become an increasingly dominant factor in the design of both portable and desk-top systems. An effective way to reduce power consumption is to lower the supply voltage since voltage is quadratically related to power. This dissertation considers the problem of lowering the supply voltage at (i) the system level and at (ii) the behavioral level. At the system level, the voltage of the variable voltage processor is dynamically changed with the work load. Processors with limited sized buffers as well as those with very large buffers are considered. Given the task arrival times, deadline times, execution times, periods and switching activities, task scheduling algorithms that minimize energy or peak power are developed for the processors equipped with very large buffers. A relation between the operating voltages of the tasks for minimum energy/power is determined using the Lagrange multiplier method, and an iterative algorithm that utilizes this relation is developed. Experimental results show that the voltage assignment obtained by the proposed algorithm is very close (0.1% error) to that of the optimal energy assignment and the optimal peak power (1% error) assignment. Next, on-line and off-fine minimum energy task scheduling algorithms are developed for processors with limited sized buffers. These algorithms have polynomial time complexity and present optimal (off-line) and close-to-optimal (on-line) solutions. A procedure to calculate the minimum buffer size given information about the size of the task (maximum, minimum), execution time (best case, worst case) and deadlines is also presented. At the behavioral level, resources operating at multiple voltages are used to minimize power while maintaining the throughput. Such a scheme has the advantage of allowing modules on the critical paths to be assigned to the highest voltage levels (thus meeting the required timing constraints) while allowing modules on non-critical paths to be assigned

  14. 计及动态无功控制影响的大规模风电汇集地区电压稳定性分析%Analysis on voltage stability in large-scale wind farms integration area considering impact of dynamic reactive power control

    Institute of Scientific and Technical Information of China (English)

    周红婷; 宋玮

    2016-01-01

    为了进一步分析大规模风电汇集地区电压稳定性,提出应考虑风电场动态无功控制的影响。基于电压-无功灵敏度法解释了动态无功补偿装置的恒无功控制方式所带来的汇集地区电压上升问题。利用小扰动稳定法,分析出采用高压侧恒电压控制的风电场内动态无功补偿装置之间存在很强的相互作用,并会引起不稳定的电压振荡。以华北某风电汇集地区为例,在PSS/E中比较分析区内所有风电场内动态无功补偿装置分别采用恒无功、高压侧恒电压和低压侧恒电压三种控制方式时受到小扰动后的电压变化。仿真结果验证了分析结论,表明在研究风电汇集地区电压稳定性问题上,考虑风电场的动态无功控制影响是必要的。%In order to analyze voltage stability in large-scale wind farms integration area, this paper proposes that dynamic reactive power control should be considered. Presently, dynamic reactive power compensation device in wind farms widely adopts constant reactive power control. According to it, this paper firstly proposes this control mode of dynamic reactive power compensation device can bring voltage stability problem based on voltage-reactive power sensitivity method;then it uses small signal stability analysis method, consulting that there is a strong interaction between dynamic reactive power compensation devices in wind farms which adopts high-voltage side constant voltage control. As a result, it will lead to unstable high frequency oscillation;finally, taking a wind farm integration area in North China, it obtains the voltage change of all dynamic reactive power compensation device in wind farm after small disturbance when constant control mode, high-voltage side constant voltage control, and low-voltage side constant voltage control are adopted respectively. The result shows that considering dynamic reactive power control is important for voltage stability

  15. The dynamic response of a hot-wire anemometer: IV. Sine-wave voltage perturbation testing for near-wall hot-wire/film probes and the presence of low-high frequency response characteristics

    Science.gov (United States)

    Teo, C. J.; Khoo, B. C.; Teo, C. J.; Chew, Y. T.

    2001-01-01

    Experiments were performed using the electronic sine-wave voltage-perturbation test to systematically study the frequency responses of near-wall hot-wire probes subjected in turn to varying magnitudes of convective velocity and different effects of wall influence. In addition, quartz-substrate hot-film gauges with various thicknesses of quartz coating were also investigated. Results of the high cut-off frequency obtained using the sine-wave test (fsine) were found to be in fair agreement with those obtained using the square-wave test (fS) both for hot-wire and for hot-film sensors. The sine-wave test response curve exhibited a distinct bulging effect for the hot-film gauges. For the hot-wire sensors, a much weaker bulging effect was also observed. In contrast to fS and fsine, the low frequency response characteristic corresponding to the location of the bulging effect (fbulge) compared much more favourably with the dynamic frequency response (fD) obtained by Khoo et al and Chew et al using a known near-wall fluctuating flow field. Freymuth's theory for non-cylindrical hot-film sensors incorporating the Bellhouse-Schultz model was applied to predict the responses of the hot-film wall gauges when they were subjected to electronic sine-wave testing and dynamic perturbation testing under different parametric conditions. Although it is one-dimensional in nature, the model is capable of predicting most of the trends observed in the present study and previous works by Khoo et al (1998a) and Chew et al (1998a).

  16. Deployment of low-voltage regulator considering existing voltage control in medium-voltage distribution systems

    Directory of Open Access Journals (Sweden)

    Hiroshi Kikusato

    2016-01-01

    Full Text Available Many photovoltaic (PV systems have been installed in distribution systems. This installation complicates the maintenance of all voltages within the appropriate range in all low-voltage distribution systems (LVDSs because the trends in voltage fluctuation differ in each LVDS. The installation of a low-voltage regulator (LVR that can accordingly control the voltage in each LVDS has been studied as a solution to this problem. Voltage control in a medium-voltage distribution system must be considered to study the deployment of LVRs. In this study, we installed LVRs in the LVDSs in which the existing voltage-control scheme cannot prevent voltage deviation and performed a numerical simulation by using a distribution system model with PV to evaluate the deployment of the LVRs.

  17. High Voltage Charge Pump

    KAUST Repository

    Emira, Ahmed A.

    2014-10-09

    Various embodiments of a high voltage charge pump are described. One embodiment is a charge pump circuit that comprises a plurality of switching stages each including a clock input, a clock input inverse, a clock output, and a clock output inverse. The circuit further comprises a plurality of pumping capacitors, wherein one or more pumping capacitors are coupled to a corresponding switching stage. The circuit also comprises a maximum selection circuit coupled to a last switching stage among the plurality of switching stages, the maximum selection circuit configured to filter noise on the output clock and the output clock inverse of the last switching stage, the maximum selection circuit further configured to generate a DC output voltage based on the output clock and the output clock inverse of the last switching stage.

  18. Increased voltage photovoltaic cell

    Science.gov (United States)

    Ross, B.; Bickler, D. B.; Gallagher, B. D. (Inventor)

    1985-01-01

    A photovoltaic cell, such as a solar cell, is provided which has a higher output voltage than prior cells. The improved cell includes a substrate of doped silicon, a first layer of silicon disposed on the substrate and having opposite doping, and a second layer of silicon carbide disposed on the first layer. The silicon carbide preferably has the same type of doping as the first layer.

  19. High Voltage Seismic Generator

    Science.gov (United States)

    Bogacz, Adrian; Pala, Damian; Knafel, Marcin

    2015-04-01

    This contribution describes the preliminary result of annual cooperation of three student research groups from AGH UST in Krakow, Poland. The aim of this cooperation was to develop and construct a high voltage seismic wave generator. Constructed device uses a high-energy electrical discharge to generate seismic wave in ground. This type of device can be applied in several different methods of seismic measurement, but because of its limited power it is mainly dedicated for engineering geophysics. The source operates on a basic physical principles. The energy is stored in capacitor bank, which is charged by two stage low to high voltage converter. Stored energy is then released in very short time through high voltage thyristor in spark gap. The whole appliance is powered from li-ion battery and controlled by ATmega microcontroller. It is possible to construct larger and more powerful device. In this contribution the structure of device with technical specifications is resented. As a part of the investigation the prototype was built and series of experiments conducted. System parameter was measured, on this basis specification of elements for the final device were chosen. First stage of the project was successful. It was possible to efficiently generate seismic waves with constructed device. Then the field test was conducted. Spark gap wasplaced in shallowborehole(0.5 m) filled with salt water. Geophones were placed on the ground in straight line. The comparison of signal registered with hammer source and sparker source was made. The results of the test measurements are presented and discussed. Analysis of the collected data shows that characteristic of generated seismic signal is very promising, thus confirms possibility of practical application of the new high voltage generator. The biggest advantage of presented device after signal characteristics is its size which is 0.5 x 0.25 x 0.2 m and weight approximately 7 kg. This features with small li-ion battery makes

  20. Belowground eco-restoration of a suburban waste-storage landscape: Earthworm dynamics in grassland and in a succession of woody vegetation covers☆

    Science.gov (United States)

    Morales, Pamela K.; Yunusa, Isa A.M.; Lugg, Glenys; Li, Zheng; Gribben, Paul; Eamus, Derek

    2013-01-01

    Restoration of belowground ecology is seldom a priority in designing revegetation strategies for disturbed landscapes. We determined earthworm abundance and diversity in a 16-year old grass sward (grassland), a 6-year old (Plantation-04) and a 4-year old (Plantation-06) plantation, both of mixed woody species, on a reclaimed waste disposal site, and in nearby remnant woodland, in suburban Sydney, Australia. While no catches were made in autumn, more earthworms were found in spring (21 ± 8.6 m–2) than in winter (10.2 ± 5.9 m–2) or summer (14.4 ± 5.5 m–2). Earthworm abundance in spring was in the order grassland ≈ Plantation-04 (35.2 m–2) > woodland (12.8 m–2) > Plantation-06 (0.8 m–2). None of the revegetated covers had restored earthworm diversity to levels found in the woodland. Exotic species, mostly Microscolex dubius, dominated in the four vegetation covers at any time; the only two native species (Heteroporodrilus sp. and Megascoleceides sp.) found were in the woodland. We also assessed how quality of the evolving soils from the three revegetated covers, compared with that from the woodland, impacted viability of common exotic earthworm species. Both weight gain and cocoon production by the exotic earthworms were higher in the soil from Plantation-04 than in soils from the other vegetation covers, including the woodland; the two variables were positively correlated with the pH and mineral nutrient content (as indicated by electrical conductivity that was in turn correlated with clay content) of the soil. Age of vegetation rather than its composition explained differences in the level of earthworm recovery observed. PMID:25550677

  1. Belowground eco-restoration of a suburban waste-storage landscape: Earthworm dynamics in grassland and in a succession of woody vegetation covers.

    Science.gov (United States)

    Morales, Pamela K; Yunusa, Isa A M; Lugg, Glenys; Li, Zheng; Gribben, Paul; Eamus, Derek

    2013-12-01

    Restoration of belowground ecology is seldom a priority in designing revegetation strategies for disturbed landscapes. We determined earthworm abundance and diversity in a 16-year old grass sward (grassland), a 6-year old (Plantation-04) and a 4-year old (Plantation-06) plantation, both of mixed woody species, on a reclaimed waste disposal site, and in nearby remnant woodland, in suburban Sydney, Australia. While no catches were made in autumn, more earthworms were found in spring (21 ± 8.6 m(-2)) than in winter (10.2 ± 5.9 m(-2)) or summer (14.4 ± 5.5 m(-2)). Earthworm abundance in spring was in the order grassland ≈ Plantation-04 (35.2 m(-2)) > woodland (12.8 m(-2)) > Plantation-06 (0.8 m(-2)). None of the revegetated covers had restored earthworm diversity to levels found in the woodland. Exotic species, mostly Microscolex dubius, dominated in the four vegetation covers at any time; the only two native species (Heteroporodrilus sp. and Megascoleceides sp.) found were in the woodland. We also assessed how quality of the evolving soils from the three revegetated covers, compared with that from the woodland, impacted viability of common exotic earthworm species. Both weight gain and cocoon production by the exotic earthworms were higher in the soil from Plantation-04 than in soils from the other vegetation covers, including the woodland; the two variables were positively correlated with the pH and mineral nutrient content (as indicated by electrical conductivity that was in turn correlated with clay content) of the soil. Age of vegetation rather than its composition explained differences in the level of earthworm recovery observed.

  2. Requirement of ultra-high voltage GIS arrester to voltage gradient of metal-oxide varistor

    Institute of Scientific and Technical Information of China (English)

    HE JinLiang; HU Jun; MENG BoWen; ZHANG Bo; ZHU Bin; CHEN ShuiMing; ZENG Rong

    2009-01-01

    The surge arrestor with excellent protection characteristics would decrease the overvoltage level ap-plied on the power apparatus to reduce their insulation levels and manufacturing bottleneck. The ar-restor for the 1000-kV ultra-high voltage ac power transmission system is designed as tank-type structure. The field-circuit combination numerical method combining the three-dimensional finite ele-ment method with circuit is proposed to analyze the potential distribution of GIS arrester. By comparing several design schemes, the most effective method to improve the potential distribution along the varistor column is to increase the voltage gradient of the ZnO varistor. Synthesizing several influential factors, the suitable voltage gradient of ZnO varistor should be controlled to 435 V/mm, and the re-sulted nonuniform degree of the potential distribution along the varistor column inside the GIS arrestor would be controlled smaller than 10%. The result in this paper provides the fundamental technical in-dex for the study of the high voltage gradient ZnO varistors.

  3. Mitigation of Voltage Sags in CIGRE Low Voltage Distribution Network

    DEFF Research Database (Denmark)

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Mahat, Pukar;

    2013-01-01

    problems in the distribution system. The voltage problems dealt with in this paper are to show how to mitigate voltage sags in the CIGRE Low Voltage (LV) test network and networks like this. The voltage sags, for the tested cases in the CIGRE LV test network are mainly due to three phase faults....... The compensation of voltage sags in the different parts of CIGRE distribution network is done by using the four STATCOM compensators already existing in the test grid. The simulations are carried out in DIgSILENT power factory software version 15.0....

  4. Charge-pump voltage converter

    Science.gov (United States)

    Brainard, John P.; Christenson, Todd R.

    2009-11-03

    A charge-pump voltage converter for converting a low voltage provided by a low-voltage source to a higher voltage. Charge is inductively generated on a transfer rotor electrode during its transit past an inductor stator electrode and subsequently transferred by the rotating rotor to a collector stator electrode for storage or use. Repetition of the charge transfer process leads to a build-up of voltage on a charge-receiving device. Connection of multiple charge-pump voltage converters in series can generate higher voltages, and connection of multiple charge-pump voltage converters in parallel can generate higher currents. Microelectromechanical (MEMS) embodiments of this invention provide a small and compact high-voltage (several hundred V) voltage source starting with a few-V initial voltage source. The microscale size of many embodiments of this invention make it ideally suited for MEMS- and other micro-applications where integration of the voltage or charge source in a small package is highly desirable.

  5. Restoring the worn dentition.

    Science.gov (United States)

    Ibsen, R L; Ouellet, D F

    1992-01-01

    Strong dental materials and dental porcelains are providing dentists with restorative opportunities that are more conservative because they require less destruction of healthy tooth structure and yield a more esthetic result. In cases of severe wear due to attrition, abrasion, and erosion, this process can be stopped, restoring the esthetics and function by using proper techniques and materials. The case report described in this article demonstrates the conservative restoration of severe wear due to attrition and erosion. Teeth were lengthened, wear was restored, and further wear was ceased by using a combination of bonded porcelain, a heat, light, and self-cure resin system, and a new glass-ionomer restorative material. The result was a strong, durable restoration (that required no anesthesia) with high esthetics.

  6. Watershed Restoration Project

    Energy Technology Data Exchange (ETDEWEB)

    Julie Thompson; Betsy Macfarlan

    2007-09-27

    In 2003, the U.S. Department of Energy issued the Eastern Nevada Landscape Coalition (ENLC) funding to implement ecological restoration in Gleason Creek and Smith Valley Watersheds. This project was made possible by congressionally directed funding that was provided through the US Department of Energy, Energy Efficiency and Renewable Energy, Office of the Biomass Program. The Ely District Bureau of Land Management (Ely BLM) manages these watersheds and considers them priority areas within the Ely BLM district. These three entities collaborated to address the issues and concerns of Gleason Creek and Smith Valley and prepared a restoration plan to improve the watersheds’ ecological health and resiliency. The restoration process began with watershed-scale vegetation assessments and state and transition models to focus on restoration sites. Design and implementation of restoration treatments ensued and were completed in January 2007. This report describes the restoration process ENLC undertook from planning to implementation of two watersheds in semi-arid Eastern Nevada.

  7. Transient voltage sharing in series-coupled high voltage switches

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1992-07-01

    Full Text Available For switching voltages in excess of the maximum blocking voltage of a switching element (for example, thyristor, MOSFET or bipolar transistor such elements are often coupled in series - and additional circuitry has to be provided to ensure equal voltage sharing. Between each such series element and system ground there is a certain parasitic capacitance that may draw a significant current during high-speed voltage transients. The "open" switch is modelled as a ladder network. Analy­sis reveals an exponential progression in the distribution of the applied voltage across the elements. Overstressing thus oc­curs in some of the elements at levels of the total voltage that are significantly below the design value. This difficulty is overcome by grading the voltage sharing circuitry, coupled in parallel with each element, in a prescribed manner, as set out here.

  8. No-Voltage Meter

    Science.gov (United States)

    1976-02-01

    VW- IKft, 1/4 H4 -Wv- IK!1, I/4W INTERNAL VOLTAGE NOTE ALL TRANSISTORS ARE 2N43A OR EQUIVALENT GERMANIUM ALLOY PNP AA ALKALINE BATTERY...D-,, regardless of polarity. This signal is then full-wave rectified by the diode-connected Germanium transistor bridge, T,, T-,, T3, and T4... Transistor T5 acts as a second current limiter. Resistor R2 was selected to give 90 f# of full-scale meter deflection with an input signal of 115 volts

  9. Benchmarking of Voltage Sag Generators

    DEFF Research Database (Denmark)

    Yang, Yongheng; Blaabjerg, Frede; Zou, Zhixiang

    2012-01-01

    The increased penetration of renewable energy systems, like photovoltaic and wind power systems, rises the concern about the power quality and stability of the utility grid. Some regulations for Low Voltage Ride-Through (LVRT) for medium voltage or high voltage applications, are coming into force...... to guide these grid-connected distributed power generation systems. In order to verify the response of such systems for voltage disturbance, mainly for evaluation of voltage sags/dips, a Voltage Sag Generator (VSG) is needed. This paper evaluates such sag test devices according to IEC 61000 in order...... to provide cheaper solutions to test against voltage sags. Simulation and experimental results demonstrate that the shunt impedance based VSG solution is the easiest and cheapest one for laboratory test applications. The back-to-back fully controlled converter based VSG is the most flexible solution...

  10. Voltage and Current Regulators Design of Power Converters in Islanded Microgrids based on State Feedback Decoupling

    DEFF Research Database (Denmark)

    Federico, de Bosio; de Sousa Ribeiro, Luiz Antonio; Freijedo Fernandez, Francisco Daniel

    2016-01-01

    In stand-alone microgrids based on voltage source inverters state feedback coupling between the capacitor voltage and inductor current degrades significantly the dynamics performance of voltage and current regulators. The decoupling of the controlled states is proposed, considering the limitations...... introduced by system delays. Moreover, a proportional resonant voltage controller is designed according to Nyquist criterion taking into account application requirements. Experimental tests performed in compliance with the UPS standards verify the theoretical analysis....

  11. Discrete iterative-map mo deling and dynamical analysis of digital voltage-mo de controlled buck converter with dual-edge mo dulation%基于双缘调制的数字电压型控制Buck变换器离散迭代映射建模与动力学分析∗

    Institute of Scientific and Technical Information of China (English)

    刘啸天; 周国华; 李振华; 陈兴

    2015-01-01

    The operation principle of digital voltage-mode controlled buck converter with dual-edge modulation is analyzed in this paper. Based on the state equation of buck converter and six possible evolutions in one switching cycle, the discrete iterative-map model of digital voltage-mode controlled buck converter with dual-edge modulation is established. Ignoring the quantization error of analog-digital converter and on the basis of its discrete iterative-map model, the nonlinear dynamical behavior of digital voltage-mode controlled buck converter with dual-edge modulation is investigated in detail. Taking the input voltage and the load resistance as bifurcation parameters, the output voltage bifurcation diagram and the inductor current bifurcation diagram are plotted. Through analyzing the bifurcation diagrams, it is indicated that there are two kinds of similar but different Hopf bifurcation phenomena. By use of Poincar´e section, time-domain simulation waveforms and phase portraits, two different Hopf bifurcations and low-frequency oscillation phenomena are compared and studied. Observing the inductor current and capacitor voltage waveforms respectively, it is obviously found that their oscillation frequencies and amplitudes are different, the shapes of two Poincar´e sections and phase portraits are also different. In order to verify the correctness of the simulation and theoretical analysis, the eigenvalues of Jacobian matrix of the discrete iterative map model are introduced and solved in two kinds of stable evolutions. Through analyzing variation of eigenvalues of Jacobi matrix with input voltage, the existence and difference of two kinds of Hopf bifurcation phenomena are proved theoretically. Moreover, it is observed in this paper that the odd period-doubling bifurcation phenomenon exists in digital voltage-mode controlled buck converter with dual-edge modulation for the first time, where the operation state of the buck converter turns from period-one into period

  12. Coordinated Voltage Control of Distributed PV Inverters for Voltage Regulation in Low Voltage Distribution Networks

    DEFF Research Database (Denmark)

    Nainar, Karthikeyan; Pokhrel, Basanta Raj; Pillai, Jayakrishnan Radhakrishna

    2017-01-01

    This paper reviews and analyzes the existing voltage control methods of distributed solar PV inverters to improve the voltage regulation and thereby the hosting capacity of a low-voltage distribution network. A novel coordinated voltage control method is proposed based on voltage sensitivity...... analysis, which is simple for computation and requires moderate automation and communication infrastructure. The proposed method is suitable for a hierarchical control structure where a supervisory controller has the provision to adapt the settings of local PV inverter controllers for overall system...

  13. Heat-pump performance: voltage dip/sag, under-voltage and over-voltage

    Directory of Open Access Journals (Sweden)

    William J.B. Heffernan

    2014-12-01

    Full Text Available Reverse cycle air-source heat-pumps are an increasingly significant load in New Zealand and in many other countries. This has raised concern over the impact wide-spread use of heat-pumps may have on the grid. The characteristics of the loads connected to the power system are changing because of heat-pumps. Their performance during under-voltage events such as voltage dips has the potential to compound the event and possibly cause voltage collapse. In this study, results from testing six heat-pumps are presented to assess their performance at various voltages and hence their impact on voltage stability.

  14. Toponymic Restoration in Irkutsk

    Directory of Open Access Journals (Sweden)

    Alexander Snarsky

    2016-10-01

    Full Text Available The article analyzes the discussion on restoration of historical names of public spaces in Irkutsk. It also reviews different approaches to the problem that appeared in the historical science and publicism. The author says about the necessity of a strictly historical approach to the toponymic restoration.

  15. Guiding Restoration Principles

    Science.gov (United States)

    2004-12-01

    restoration of important ecosystem functions requires reintegrating landscapes or restorating the func- tional aspects of landscapes ( Risser 1992...51-64. Risser , P. G. 1992. Landscape ecology approach to ecosystem rehabilitation. Pages 37-46 in M. L. Wali (ed.), Ecosystem Rehabilitation

  16. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    Science.gov (United States)

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores.

  17. Setting targets in strategies for river restoration

    NARCIS (Netherlands)

    Pedroli, G.B.M.; Blust, de G.; Looy, van K.; Rooij, van S.A.M.

    2002-01-01

    Since about 90% of the natural floodplain area of rivers in Europe has been reclaimed and now lacks river dynamics, nature rehabilitation along rivers is of crucial importance for the restoration of their natural function. Flood protection, self-purification of surface water, groundwater recharge, s

  18. Plural voltage minima in an arc-heated channel flow

    Science.gov (United States)

    Sasoh, A.

    2001-04-01

    In flows through a channel with varying cross-sectional area, the impulse and total enthalpy can be increased by superimposing an electrical discharge. The flow field is determined from the inlet flow condition, channel geometry, and discharge specifications. In this study, steady-state, quasi-one-dimensional flows interacting with an arc discharge are computed numerically. Once the arc column configuration is given, the discharge voltage is computed from the solution of flow field variables. For a constant discharge current, there exist plural column configurations which yield a minimum discharge voltage. This result explains the fluid-dynamic mechanisms of the existence of plural voltage modes in an arcjet operation.

  19. Enhanced current and voltage regulators for stand-alone applications

    DEFF Research Database (Denmark)

    Federico, de Bosio; Pastorelli, Michele; Antonio DeSouza Ribeiro, Luiz

    2016-01-01

    State feedback decoupling permits to achieve a better dynamic response for Voltage Source in stand-alone applications. The design of current and voltage regulators is performed in the discrete-time domain since it provides better accuracy and allows direct pole placement. As the attainable...... bandwidth of the current loop is mainly limited by computational and PWM delays, a lead compensator structure is proposed to overcome this limitation. The design of the voltage regulator is based on the Nyquist criterion, verifying to guarantee a high sensitivity peak. Discrete-time domain implementation...

  20. Mechanism of electromechanical coupling in voltage-gated potassium channels

    Directory of Open Access Journals (Sweden)

    Rikard eBlunck

    2012-09-01

    Full Text Available Voltage-gated ion channels play a central role in the generation of action potentials in the nervous system. They are selective for one type of ion – sodium, calcium or potassium. Voltage-gated ion channels are composed of a central pore that allows ions to pass through the membrane and four peripheral voltage sensing domains that respond to changes in the membrane potential. Upon depolarization, voltage sensors in voltage-gated potassium channels (Kv undergo conformational changes driven by positive charges in the S4 segment and aided by pairwise electrostatic interactions with the surrounding voltage sensor. Structure-function relations of Kv channels have been investigated in detail, and the resulting models on the movement of the voltage sensors now converge to a consensus; the S4 segment undergoes a combined movement of rotation, tilt and vertical displacement in order to bring 3-4 e+ each through the electric field focused in this region. Nevertheless, the mechanism by which the voltage sensor movement leads to pore opening, the electromechanical coupling, is still not fully understood. Thus, recently, electromechanical coupling in different Kv channels has been investigated with a multitude of techniques including electrophysiology, 3D crystal structures, fluorescence spectroscopy and molecular dynamics simulations. Evidently, the S4-S5 linker, the covalent link between the voltage sensor and pore, plays a crucial role. The linker transfers the energy from the voltage sensor movement to the pore domain via an interaction with the S6 C-termini, which are pulled open during gating. In addition, other contact regions have been proposed. This review aims to provide (i an in-depth comparison of the molecular mechanisms of electromechanical coupling in different Kv channels; (ii insight as to how the voltage sensor and pore domain influence one another; and (iii theoretical predictions on the movement of the cytosolic face of the KV channels

  1. Social Science Methods Used in the RESTORE Project

    Science.gov (United States)

    Lynne M. Westphal; Cristy Watkins; Paul H. Gobster; Liam Heneghan; Kristen Ross; Laurel Ross; Madeleine Tudor; Alaka Wali; David H. Wise; Joanne Vining; Moira. Zellner

    2014-01-01

    The RESTORE (Rethinking Ecological and Social Theories of Restoration Ecology) project is an interdisciplinary, multi-institutional research endeavor funded by the National Science Foundation's Dynamics of Coupled Natural Human Systems program. The goal of the project is to understand the links between organizational type, decision making processes, and...

  2. Voltage Dependence of Supercapacitor Capacitance

    Directory of Open Access Journals (Sweden)

    Szewczyk Arkadiusz

    2016-09-01

    Full Text Available Electronic Double-Layer Capacitors (EDLC, called Supercapacitors (SC, are electronic devices that are capable to store a relatively high amount of energy in a small volume comparing to other types of capacitors. They are composed of an activated carbon layer and electrolyte solution. The charge is stored on electrodes, forming the Helmholtz layer, and in electrolyte. The capacitance of supercapacitor is voltage- dependent. We propose an experimental method, based on monitoring of charging and discharging a supercapacitor, which enables to evaluate the charge in an SC structure as well as the Capacitance-Voltage (C-V dependence. The measurement setup, method and experimental results of charging/discharging commercially available supercapacitors in various voltage and current conditions are presented. The total charge stored in an SC structure is proportional to the square of voltage at SC electrodes while the charge on electrodes increases linearly with the voltage on SC electrodes. The Helmholtz capacitance increases linearly with the voltage bias while a sublinear increase of total capacitance was found. The voltage on SC increases after the discharge of electrodes due to diffusion of charges from the electrolyte to the electrodes. We have found that the recovery voltage value is linearly proportional to the initial bias voltage value.

  3. Optimal coordinated voltage control of power systems

    Institute of Scientific and Technical Information of China (English)

    LI Yan-jun; HILL David J.; WU Tie-jun

    2006-01-01

    An immune algorithm solution is proposed in this paper to deal with the problem of optimal coordination of local physically based controllers in order to preserve or retain mid and long term voltage stability. This problem is in fact a global coordination control problem which involves not only sequencing and timing different control devices but also tuning the parameters of controllers. A multi-stage coordinated control scheme is presented, aiming at retaining good voltage levels with minimal control efforts and costs after severe disturbances in power systems. A self-pattern-recognized vaccination procedure is developed to transfer effective heuristic information into the new generation of solution candidates to speed up the convergence of the search procedure to global optima. An example of four bus power system case study is investigated to show the effectiveness and efficiency of the proposed algorithm, compared with several existing approaches such as differential dynamic programming and tree-search.

  4. A Policy Analysis Perspective on Ecological Restoration

    Directory of Open Access Journals (Sweden)

    Susan Baker

    2013-06-01

    Full Text Available Using a simple stages model of the policy process, we explore the politics of ecological restoration using an array of examples drawn across sector, different size and scale, and from different countries. A policy analysis perspective reveals how, at both the program and project levels, ecological restoration operates within a complex and dynamic interplay between technical decision making, ideologies, and interest politics. Viewed through the stages model, restoration policy involves negotiating nature across stages in the policy making process, including agenda setting, policy formulation, implementation, and evaluation. The stages model is a useful heuristic devise; however, this linear model assumes that policy makers approach the issue rationally. In practice, ecological restoration policy takes place in the context of different distributions of power between the various public and private actors involved at the different stages of restoration policy making. This allows us to reiterate the point that ecological restoration is best seen not only as a technical task but as a social and political project.

  5. DIRECT PERMANENT RESTORATIVES - AMALGAM VS COMPOSITE

    Directory of Open Access Journals (Sweden)

    Bhagyashree

    2013-11-01

    Full Text Available ABSTRACT: Dental restoration is the most commonly administered dental treatment. These restorations are subjected to dynamic conditions in oral cavity, are likely to fail and need replacement. Ideal restorative material should pass two tests - Longitivity and Esthetics. Longitivity of the restorative material depends on three major factors - first is Patient’s factors, second is Operator`s skills and last is the Restorative material itself. Dentists today have a plethora of materials to choose from. Materials like Silver Amalgam being tested over a century, other nubile but promising materials, developed recently and yet to be tested in long run. This puts a dentist in dilemma so as which material to select to ensure durable clinical p erformance after placement. Amalgam has been tested over 165 years and has fulfilled almost all desired qualities of a restorative material except esthetics. On the other hand composites have advantage in cases where esthetics is of prime importance; howev er Recent studies conclude them at par with amalgam 1 . Performance of these two materials is assessed on following criterions - Longevity, wear resistance, cost effectiveness, marginal leakage and predisposal to secondary decay, biocompatibility, pulp irri tation, tooth preparation, technique sensitivity and esthetics

  6. 电压反馈型半桥DC-DC变换器动力学特性%Dynamical Characteristic for Voltage-Feedback Half-Bridge DC-DC Converter

    Institute of Scientific and Technical Information of China (English)

    袁臣虎; 万健如; 李光叶; 周海亮

    2012-01-01

    Voltage-feedback half-bridge DC-DC converter, namely VCHB DC-DC, a dominant component of SMPS system, has rich dynamical characteristic. For revealing internal relation between system stability and circuit parameters, VCHB DC-DC converter was studied in detail. According to practical closed-loop control logic, the general simulation model was set up by using the exact state equations. And the general discrete mathematical model was deduced by stroboscopic maps. Nonlinearity characteristic of VCHB DC-DC converter under different parameters was simulated and analyzed by numerical method. Experimental results show that VCHB DC-DC converter is sensitive to transformer ratio, filter capacitor, inductive storage and error scale factor, while it is not sensitive to changes in error integral coefficient and load. The research results could serve as guidance for circuit parameters selection in VCHB DC-DC converter application.%电压反馈型半桥DC-DC (VCHB DC-DC)变换器组成的开关电源系统是强非线性系统,为揭示其系统稳定性与电路参数之间的内在关系,对VCHB DC-DC变换器进行了研究.结合其实际闭环控制逻辑,利用VCHB DC-DC变换器精确状态方程,建立VCHB DC-DC变换器仿真模型,采用频闪映射对其状态变量进行离散迭代映射,推导其统一的离散数学模型.对不同参数下VCHB DC-DC变换器非线性特性进行仿真和数值分析,并进行相应实验验证.研究结果表明,变压器变比、滤波电容、储能电感和误差比例系数的改变对VCHB DC-DC变换器稳定性影响大,而误差积分系数和负载的变化对其影响较弱.研究成果可为VCHB DC-DC变换器实际应用时的电路参数选取提供指导.

  7. Challenges of ecological restoration

    DEFF Research Database (Denmark)

    Halme, Panu; Allen, Katherine A.; Aunins, Ainars

    2013-01-01

    on Biological Diversity. Several northern countries are now taking up this challenge by restoring forest biodiversity with increasing intensity. The ecology and biodiversity of boreal forests are relatively well understood making them a good model for restoration activities in many other forest ecosystems. Here......The alarming rate of ecosystem degradation has raised the need for ecological restoration throughout different biomes and continents. North European forests may appear as one of the least vulnerable ecosystems from a global perspective, since forest cover is not rapidly decreasing and many...... ecosystem services remain at high level. However, extensive areas of northern forests are heavily exploited and have lost a major part of their biodiversity value. There is a strong requirement to restore these areas towards a more natural condition in order to meet the targets of the Convention...

  8. Restoration of ailing wetlands.

    Directory of Open Access Journals (Sweden)

    Oswald J Schmitz

    2012-01-01

    Full Text Available It is widely held that humankind's destructive tendencies when exploiting natural resources leads to irreparable harm to the environment. Yet, this thinking runs counter to evidence that many ecological systems damaged by severe natural environmental disturbances (e.g., hurricanes can restore themselves via processes of natural recovery. The emerging field of restoration ecology is capitalizing on the natural restorative tendencies of ecological systems to build a science of repairing the harm inflicted by humans on natural environment. Evidence for this, for example, comes from a new meta-analysis of 124 studies that synthesizes recovery of impacted wetlands worldwide. While it may take up to two human generations to see full recovery, there is promise, given human will, to restore many damaged wetlands worldwide.

  9. Science of landscape restoration

    CSIR Research Space (South Africa)

    De Wet, Benita

    2011-11-01

    Full Text Available Over the last two decades the ecological restoration of industrial land has developed into a specialist science combined with highly sophisticated management activities. A prime example of this approach is a unique partnership between the CSIR...

  10. Image restoration scale space

    Science.gov (United States)

    Alvarez, Luis; Mazorra, L.; Santana, F.

    1995-09-01

    We present a study of some image resoration techniques based on partial differential equations. We study separately the denoising problem and the restoration of discontinuities. We analyze the capabilities of the differential operators to restore images. In particular, we analyze a number of models present in the literature, and we present comparative results. Finally, we present a model based in the combination of the anisotropic diffusion of Alvarez, Lions, and Morel and the shock filters of Osher and Rudin.

  11. Restoring primary anterior teeth.

    Science.gov (United States)

    Waggoner, William F

    2002-01-01

    A variety of esthetic restorative materials are available for restoring primary incisors. Knowledge of the specific strengths, weakness, and properties of each material will enhance the clinician's ability to make the best choice of selection for each individual situation. Intracoronal restorations of primary teeth may utilize resin composites, glass ionomer cements, resin-modified ionomers, or polyacid-modified resins. Each has distinct advantages and disadvantages and the clinical conditions of placement may be a strong determining factor as to which material is utilized. Full coronal restoration of primary incisors may be indicated for a number of reasons. Crowns available for restoration of primary incisors include those that are directly bonded onto the tooth, which generally are a resin material, and those crowns that are luted onto the tooth and are some type of stainless steel crown. However, due to lack of supporting clinical data, none of the crowns can be said to be superior to the others under all circumstances. Though caries in the mandibular region is rare, restorative solutions for mandibular incisors are needed. Neither stainless steel crowns nor celluloid crown forms are made specifically for mandibular incisors. Many options exist to repair carious primary incisors, but there is insufficient controlled, clinical data to suggest that one type of restoration is superior to another. This does not discount the fact that dentists have been using many of these crowns for years with much success. Operator preferences, esthetic demands by parents, the child's behavior, and moisture and hemorrhage control are all variables which affect the decision and ultimate outcome of whatever restorative treatment is chosen.

  12. Restoration in South Africa

    CSIR Research Space (South Africa)

    Blignaut, J

    2010-01-01

    Full Text Available is restoration? Our human population continues to grow at an unprecedented rate, demanding ever-increasing amounts of goods and services from the natural ecosystems upon which we depend. No part of the planet has been left untouched, and many areas.... Another selection criterion was the need for historic data and a restoration history. In each of the cases the ASSET Research team collaborates with partners, that include the Working for Water programme, Flower Valley, the Ostrich Business Chamber...

  13. Application of Load Compensation in Voltage Controllers of Large Generators in the Polish Power Grid

    Directory of Open Access Journals (Sweden)

    Bogdan Sobczak

    2014-03-01

    Full Text Available The Automatic Voltage Regulator normally controls the generator stator terminal voltage. Load compensation is used to control the voltage which is representative of the voltage at a point either within or external to the generator. In the Polish Power Grid (PPG compensation is ready to use in every AVR of a large generator, but it is utilized only in the case of generators operating at the same medium voltage buses. It is similar as in most European Power Grids. The compensator regulating the voltage at a point beyond the machine terminals has significant advantages in comparison to the slower secondary Voltage and Reactive Power Control System (ARNE1. The compensation stiffens the EHV grid, which leads to improved voltage quality in the distribution grid. This effect may be particularly important in the context of the dynamic development of wind and solar energy.

  14. Ecosystem Restoration: A Manager's Perspective

    Science.gov (United States)

    James G. Kenna; Gilpin R., Jr. Robinson; Bill Pell; Michael A. Thompson; Joe McNeel

    1999-01-01

    Elements of ecological restoration underlie much of what we think of as ecosystem management, and restoration projects on federal lands represent some of the most exciting, challenging, and convincing demonstrations of applied ecosystem management. The Society for Ecological Restoration defined restoration as "the process of reestablishing to the extent possible...

  15. Asymmetry of Polarization Reversal and Current-Voltage Characteristics of Pt/PZT-Film/Pt:Ti/SiO2/Si-Substrate Structures

    Directory of Open Access Journals (Sweden)

    S. L. Bravina

    2011-01-01

    Full Text Available The characterization of the asymmetries of bipolar charge-voltage and current-voltage loops of polarization reversal and unipolar current-voltage curves for Pt/PZT-film/Pt:Ti/SiO2/Si-substrate systems was performed in the dynamic mode. The asymmetry of local deformation-voltage loops was observed by piezoresponse force microscopy. The comparison of the dependences of introduced asymmetry factors for the bipolar charge-voltage and current-voltage loops and unipolar current-voltage curves on drive voltage indicates the interconnection of ferroelectric and electrical space charge transfer asymmetries.

  16. Time varying voltage combustion control and diagnostics sensor

    Science.gov (United States)

    Chorpening, Benjamin T.; Thornton, Jimmy D.; Huckaby, E. David; Fincham, William

    2011-04-19

    A time-varying voltage is applied to an electrode, or a pair of electrodes, of a sensor installed in a fuel nozzle disposed adjacent the combustion zone of a continuous combustion system, such as of the gas turbine engine type. The time-varying voltage induces a time-varying current in the flame which is measured and used to determine flame capacitance using AC electrical circuit analysis. Flame capacitance is used to accurately determine the position of the flame from the sensor and the fuel/air ratio. The fuel and/or air flow rate (s) is/are then adjusted to provide reduced flame instability problems such as flashback, combustion dynamics and lean blowout, as well as reduced emissions. The time-varying voltage may be an alternating voltage and the time-varying current may be an alternating current.

  17. Voltage Sensors Monitor Harmful Static

    Science.gov (United States)

    2009-01-01

    A tiny sensor, small enough to be worn on clothing, now monitors voltage changes near sensitive instruments after being created to alert Agency workers to dangerous static buildup near fuel operations and avionics. San Diego s Quasar Federal Systems received a Small Business Innovation Research (SBIR) contract from Kennedy Space Center to develop its remote voltage sensor (RVS), a dime-sized electrometer designed to measure triboelectric changes in the environment. One of the unique qualities of the RVS is that it can detect static at greater distances than previous devices, measuring voltage changes from a few centimeters to a few meters away, due to its much-improved sensitivity.

  18. SURVEY AND RESTORATION

    Directory of Open Access Journals (Sweden)

    C. Mileto

    2017-05-01

    Full Text Available In addition to the technological evolution over the last two centuries, survey has experienced two main conceptual leaps: the introduction of photography as a tool for an indiscriminate register for reality, and the shift from autographic to allographic survey, phenomena which can generate a distancing effect within the restoration process. Besides, this text presents the relationship between survey in its numerous forms and technologies (manual and semi-manual to more complex ones like scanner-laser and the restoration of the building, either for establishing a diagnosis, operating or valorizating, illustrating it with examples developed by the authors, as well as the criteria to be applied when documenting a building to be restored, irrespective of the means and technology available in each case.

  19. [New direct restorative materials].

    Science.gov (United States)

    Hickel, R; Dasch, W; Janda, R; Tyas, M; Anusavice, K

    1999-04-01

    People worldwide have become increasingly aware of the potential adverse effects on the environment, of pollution control and of toxic effects of food, drugs and biomaterials. Amalgam and its potential toxic side effects (still scientifically unproven) continue to be discussed with increasing controversy by the media in some countries. Consequently, new direct restorative materials are now being explored by dentists, materials scientists and patients who are searching for the so-called 'amalgam substitute' or 'amalgam alternative'. From a critical point of view some of the new direct restorative materials are good with respect in aesthetics, but all material characteristics must be considered, such as mechanical properties, biological effects, and longterm clinical behaviour.

  20. Process Fairness and Dynamic Consistency

    NARCIS (Netherlands)

    S.T. Trautmann (Stefan); P.P. Wakker (Peter)

    2010-01-01

    textabstractAbstract: When process fairness deviates from outcome fairness, dynamic inconsistencies can arise as in nonexpected utility. Resolute choice (Machina) can restore dynamic consistency under nonexpected utility without using Strotz's precommitment. It can similarly justify dynamically

  1. Low Voltage Power Supply Incorporating Ceramic Transformer

    CERN Document Server

    Imori, M

    2007-01-01

    A low voltage power supply provides the regulated output voltage of 1 V from the supply voltage around 48 V. The low voltage power supply incorporates a ceramic transformer which utilizes piezoelectric effect to convert voltage. The ceramic transformer isolates the secondary from the primary, thus providing the ground isolation between the supply and the output voltages. The ceramic transformer takes the place of the conventional magnetic transformer. The ceramic transformer is constructed from a ceramic bar and does not include any magnetic material. So the low voltage power supply can operate under a magnetic field. The output voltage is stabilized by feedback. A feedback loop consists of an error amplifier, a voltage controlled oscillator and a driver circuit. The amplitude ratio of the transformer has dependence on the frequency, which is utilized to stabilize the output voltage. The low voltage power supply is investigated on the analogy of the high voltage power supply similarly incorporating the cerami...

  2. Modular High Voltage Power Supply

    Energy Technology Data Exchange (ETDEWEB)

    Newell, Matthew R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-18

    The goal of this project is to develop a modular high voltage power supply that will meet the needs of safeguards applications and provide a modular plug and play supply for use with standard electronic racks.

  3. Reliability criteria for voltage stability

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Carson W.; Silverstein, Brian L. [Bonneville Power Administration, Portland, OR (United States)

    1994-12-31

    In face of costs pressures, there is need to allocate scare resources more effectively in order to achieve voltage stability. This naturally leads to development of probabilistic criteria and notions of rick management. In this paper it is presented a discussion about criteria for long term voltage stability limited to the case in which the time frames are topically several minutes. (author) 14 refs., 1 fig.

  4. A Voltage Quality Detection Method

    DEFF Research Database (Denmark)

    Chen, Zhe; Wei, Mu

    2008-01-01

    This paper presents a voltage quality detection method based on a phase-locked loop (PLL) technique. The technique can detect the voltage magnitude and phase angle of each individual phase under both normal and fault power system conditions. The proposed method has the potential to evaluate vario...... power quality disturbances, such as interruptions, sags and imbalances. Simulation studies have been performed. The effectiveness of the proposed method has been demonstrated under the simulated typical power disturbances....

  5. 基于软锁相的电压跌落检测方法%Detection Technology of Voltage Sag Based on SPLL

    Institute of Scientific and Technical Information of China (English)

    韩晓东; 彭祺; 占奇志; 卓放

    2011-01-01

    In order to improve the quality of power supply by electrical network and to protect the sensitive load from being affected by voltage fluctuation cansed by voltage short-time depreciation, the paper studies the detection of the voltage depreciation in the industry power supply network,describes a few detection methods and their characteristics with their strengths and weaknesses compared. Based on soft phase-locked-loop (SPLL) a voltage depreciation detection method is proposed with its basic principle and structure described. The method was simulated and the dynamic voltage restorer compensation experiment based on SPLL was conducted. The simulation and experimental results confirmed its validity.%为了提高电网供电质量,保护敏感负荷不受电压短时跌落造成的电压波动的影响,研究了工业供电电网中电压跌落的检测.概述并分析了现有几种电压跌落的检测方法及特点,比较了这几种方法各自的优缺点.提出了基于软锁相(Soft Phase-Locked-Loop,SPLL)的电压跌落检测方法.给出了基本原理和结构,并对软锁相的电压跌落检测方法进行了仿真,最后完成了基于SPLL检测方法的动态电压恢复器的补偿实验.该方法响应速度快,对电源电压的相位跳变和频率漂移有很好的跟踪效果.仿真和实验结果验证了这种方法的有效性.

  6. Experimental evaluation of envelope tracking techniques for voltage disturbances

    Energy Technology Data Exchange (ETDEWEB)

    Marei, Mostafa I. [Electrical Power and Machines Dept., Faculty of Engineering, Ain Shams University, 1 El-Sarayat St., Abbasia, 11517 Cairo (Egypt); El-Saadany, Ehab F.; Salama, Magdy M.A. [Electrical and Computer Engineering Dept., University of Waterloo, 200 University Avenue West, Waterloo, ON (Canada)

    2010-03-15

    In this paper a digital signal processor (DSP) based real time voltage envelope tracking system is developed and examined. The ADAptive LINEar neuron (ADALINE) and the Recursive Least Square (RLS) algorithms are adopted for envelope tracking. The proposed ADALINE and RLS algorithms give accurate results even under rapid dynamic changes. The paper investigates the effects of different parameters on the performance of the ADALINE algorithm and that of the RLS algorithm. The experimental system is cantered around a Texas Instrument 16 bit fixed-point arithmetic (TMS320LF2407A) evaluation board. Both the ADALINE and the RLS tracking algorithms are developed using the DSP-assembly language. A simple voltage flicker generator is implemented to produce various voltage disturbances. Extensive tests of the proposed envelope tracking algorithms are conducted to evaluate their dynamic performance. (author)

  7. A matter of quantum voltages.

    Science.gov (United States)

    Sellner, Bernhard; Kathmann, Shawn M

    2014-11-14

    Voltages inside matter are relevant to crystallization, materials science, biology, catalysis, and aqueous chemistry. The variation of voltages in matter can be measured by experiment, however, modern supercomputers allow the calculation of accurate quantum voltages with spatial resolutions of bulk systems well beyond what can currently be measured provided a sufficient level of theory is employed. Of particular interest is the Mean Inner Potential (V(o))--the spatial average of these quantum voltages referenced to the vacuum. Here we establish a protocol to reliably evaluate V(o) from quantum calculations. Voltages are very sensitive to the distribution of electrons and provide metrics to understand interactions in condensed phases. In the present study, we find excellent agreement with measurements of V(o) for vitrified water and salt crystals and demonstrate the impact of covalent and ionic bonding as well as intermolecular/atomic interactions. Certain aspects in this regard are highlighted making use of simple model systems/approximations. Furthermore, we predict V(o) as well as the fluctuations of these voltages in aqueous NaCl electrolytes and characterize the changes in their behavior as the resolution increases below the size of atoms.

  8. A Capacitor Voltage Dynamic Balancing Method for Multilevel Converters Based on Taking Power from Capacitors%一种基于直流电容取电的多电平变流器电容动态均压方法

    Institute of Scientific and Technical Information of China (English)

    魏应冬; 张春朋; 于心宇; 姜齐荣

    2014-01-01

    多电平变流器的电容电压不均问题影响装置容量利用率、稳定运行以及电能质量。提出一种基于直流电容取电的多电平变流器动态电阻均压装置及控制方法。该装置由低压金属氧化物半导体场效应管(metal oxide semiconductor field effect transistor,MOSFET)与电阻串联构成动态均压电阻,通过宽范围电压输入型DC-DC电源从直流电容获取功率,并采用滞回比较、占空比控制等方法控制低压MOSFET的开通和关断,实现多电平变流器各电容电压的动态均衡控制。该装置增加的成本较低,控制方法较为简单,易于实现,适用于各种多电平变流器结构,通用性较强。基于PSCAD/EMTDC的仿真表明,提出的动态电阻均压装置和控制方法能够良好地实现多电平变流器直流电容的动态均压控制。%The capacitor voltage balancing problem of multilevel converters may result in the reduction of capacity utilization,the unstable operation and the deterioration of power quality.Based on taking power from capacitor,a dynamic resistance balancing device for multilevel converters and its control method were proposed,in which the dynamic equalizing resistance consisted of a low-voltage MOSFET and a resistance in series,and the power was taken from the capacitor through a DC-DC convertor with wide range voltage input.The turn on/off of low-voltage MOSFET was controlled by hysteresis comparison method or duty ratio control method, which could implement the dynamic balance control of multilevel converter's capacitor voltage.The increased cost of the device is very low,the control method is simple and easy to implement;it has strong universality and can be applied in all kinds of multilevel converters.Based on PSCAD/EMTDC, the results show that the proposed dynamic resistance balancing device and control method can well realize the dynamic balancing control for the capacitor voltage of multilevel converter.

  9. Steady-state analysis of the effect of reactive generation limits in voltage stability

    Energy Technology Data Exchange (ETDEWEB)

    Echavarren, F.M.; Lobato, E.; Rouco, L. [School of Engineering of Universidad Pontificia Comillas, C/Alberto Aguilera, 23, 28015 Madrid (Spain)

    2009-09-15

    Voltage collapse phenomena are highly affected by reactive power generation limits. Saturation of the reactive power generation limits of a unit may result in a deterioration of the voltage stability. However, in some cases when the power network is operating close to the voltage collapse point, the reactive power generation saturation of a unit can change the system voltages immediately from stable to unstable; thus, a dynamic voltage collapse leading to blackout may follow. This paper presents a steady-state analysis of the immediate instability caused by reactive power generation saturation phenomena. For this purpose, the paper proposes a novel index that evaluates ''when'' and ''why'' a reactive power generation saturation will only result in a deterioration of the system voltage stability or, on the contrary, it will make the system voltages immediately unstable. (author)

  10. Adaptive Voltage Management Enabling Energy Efficiency in Nanoscale Integrated Circuits

    Science.gov (United States)

    Shapiro, Alexander E.

    Battery powered devices emphasize energy efficiency in modern sub-22 nm CMOS microprocessors rendering classic power reduction solutions not sufficient. Classical solutions that reduce power consumption in high performance integrated circuits are superseded with novel and enhanced power reduction techniques to enable the greater energy efficiency desired in modern microprocessors and emerging mobile platforms. Dynamic power consumption is reduced by operating over a wide range of supply voltages. This region of operation is enabled by a high speed and power efficient level shifter which translates low voltage digital signals to higher voltages (and vice versa), a key component that enables communication among circuits operating at different voltage levels. Additionally, optimizing the wide supply voltage range of signals propagating across long interconnect enables greater energy savings. A closed-form delay model supporting wide voltage range is developed to enable this capability. The model supports an ultra-wide voltage range from nominal voltages to subthreshold voltages, and a wide range of repeater sizes. To mitigate the drawback of lower operating speed at reduced supply voltages, the high performance exhibited by MOS current mode logic technology is exploited. High performance and energy efficient circuits are enabled by combining this logic style with power efficient near threshold circuits. Many-core systems that operate at high frequencies and process highly parallel workloads benefit from this combination of MCML with NTC. Due to aggressive scaling, static power consumption can in some cases overshadow dynamic power. Techniques to lower leakage power have therefore become an important objective in modern microprocessors. To address this issue, an adaptive power gating technique is proposed. This technique utilizes high levels of granularity to save additional leakage power when a circuit is active as opposed to standard power gating that saves static

  11. Restoration in Its Natural Context: How Ecological Momentary Assessment Can Advance Restoration Research

    Directory of Open Access Journals (Sweden)

    Femke Beute

    2016-04-01

    Full Text Available More and more people use self-tracking technologies to track their psychological states, physiology, and behaviors to gain a better understanding of themselves or to achieve a certain goal. Ecological Momentary Assessment (EMA also offers an excellent opportunity for restorative environments research, which examines how our physical environment (especially nature can positively influence health and wellbeing. It enables investigating restorative health effects in everyday life, providing not only high ecological validity but also opportunities to study in more detail the dynamic processes playing out over time on recovery, thereby bridging the gap between laboratory (i.e., short-term effects and epidemiological (long-term effects research. We have identified four main areas in which self-tracking could help advance restoration research: (1 capturing a rich set of environment types and restorative characteristics; (2 distinguishing intra-individual from inter-individual effects; (3 bridging the gap between laboratory and epidemiological research; and (4 advancing theoretical insights by measuring a more broad range of effects in everyday life. This paper briefly introduces restorative environments research, then reviews the state of the art of self-tracking technologies and methodologies, discusses how these can be implemented to advance restoration research, and presents some examples of pioneering work in this area.

  12. [Influence of implant restoration on traditional restoration idea].

    Science.gov (United States)

    Liu, H C

    2016-01-01

    Implant restoration affected the traditional restoration idea. Artificial implant restoration has a profound influence on the design of dental restoration. Implant supported prostheses have not only changed the method of oral rehabilitation, but also integrated revolutionary concept with the traditional treatment protocol. By using implants, posterior missing molars can be effectively restored and thus eliminating the disadvantages of traditional removable partial denture for Kennedy classification Ⅰ, Ⅱ partically edentulous dentition. Full edentulous arch can also be restored with implant fixed denture which provide much better oral health related quality of life compared with the traditional complete denture. It is useful to master the theory and skills of artificial implant restoration, and to provide a reference for the restoration of oral physiological function.

  13. Dynamic power flow controllers

    Science.gov (United States)

    Divan, Deepakraj M.; Prasai, Anish

    2017-03-07

    Dynamic power flow controllers are provided. A dynamic power flow controller may comprise a transformer and a power converter. The power converter is subject to low voltage stresses and not floated at line voltage. In addition, the power converter is rated at a fraction of the total power controlled. A dynamic power flow controller controls both the real and the reactive power flow between two AC sources having the same frequency. A dynamic power flow controller inserts a voltage with controllable magnitude and phase between two AC sources; thereby effecting control of active and reactive power flows between two AC sources.

  14. Current-Voltage Characteristics of Quasi-One-Dimensional Superconductors

    DEFF Research Database (Denmark)

    Vodolazov, D.Y.; Peeters, F.M.; Piraux, L.

    2003-01-01

    The current-voltage (I-V) characteristics of quasi-one-dimensional superconductors were discussed. The I-V characteristics exhibited an unusual S behavior. The dynamics of superconducting condensate and the existence of two different critical currents resulted in such an unusual behavior....

  15. Low Voltage CMOS op-amp with Rail-to-Rail Input/Output Swing

    OpenAIRE

    Gopalaiah, SV; Shivaprasad, AP

    2004-01-01

    As the supply voltage to a standard CMOS op-amp is reduced, the input common mode range and the output swing get reduced drastically. Special biasing circuits have to be used to raise them up to rail-to-rail supply voltage. Three low voltage op-amps with new biasing circuits have been proposed in this paper and their performance evaluated. The op-amp design is focused on dynamic range and high drive capability.

  16. Electrode voltage fall and total voltage of a transient arc

    Science.gov (United States)

    Valensi, F.; Ratovoson, L.; Razafinimanana, M.; Masquère, M.; Freton, P.; Gleizes, A.

    2016-06-01

    This paper deals with an experimental study of the components of a transient arc total voltage with duration of a few tens of ms and a current peak close to 1000 A. The cathode tip is made of graphite whereas the flat anode is made either of copper or of graphite; the electrodes gap is a few mm. The analysis of the electrical parameters is supported and validated by fast imaging and by two models: the first one is a 2D physical model of the arc allowing to calculate both the plasma temperature field and the arc voltage; the second model is able to estimate the transient heating of the graphite electrode. The main aim of the study was to detect the possible change of the cathode voltage fall (CVF) during the first instants of the arc. Indeed it is expected that during the first ms the graphite cathode is rather cool and the main mechanism of the electron emission should be the field effect emission, whereas after several tens of ms the cathode is strongly heated and thermionic emission should be predominant. We have observed some change in the apparent CVF but we have shown that this apparent change can be attributed to the variation of the solid cathode resistance. On the other hand, the possible change of CVF corresponding to the transition between a ‘cold’ and a ‘hot’ cathode should be weak and could not be characterized considering our measurement uncertainty of about 2 V. The arc column voltage (ACV) was estimated by subtracting the electrode voltage fall from the total arc voltage. The experimental transient evolution of the ACV is in very good agreement with the theoretical variation predicted by the model, showing the good ability of the model to study this kind of transient arc.

  17. Effect of semiconductor-controlled voltage injection by UPFC and ULTC on power system stability

    Science.gov (United States)

    Alavian Mehr, Alireza

    Commercial availability of various power semiconductor switches indicates proliferation of power electronic based apparatus in utility power systems. Furthermore, existing power system apparatus, e.g. mechanical phase shifters and mechanical tap changing transformers, will be retrofitted to utilize higher switching speed of semiconductor switches. A group of these apparatus, i.e., unified power flow controller (UPFC), static phase shifter (SPS), under-load tap-changing (ULTC) transformer and static series capacitor (SSC), perform their respective functions by means of injecting series controlled voltages in power systems. This thesis demonstrates that fast series voltage injection, for dynamic power flow regulation, can result in voltage dynamics and even voltage instability. This indicates that fast voltage injection by means of power electronic based apparatus can couple voltage stability and angle stability phenomena. To investigate this coupling phenomena, the voltage dependency of the load must be adequately represented in the load model. The reported studies in this work are based on representing the load by a combination of static and dynamic loads. This thesis primarily investigates impacts of UPFC and semiconductor-controlled ULTC on voltage stability and angle stability phenomena. An eigen analysis approach is used for the studies. The eigen analysis results are validated by digital time-domain simulations using a transient stability software. Both the eigen analysis and the transient stability software tools are tailored to account for angle and voltage stability phenomena.

  18. Total dose behavior of partially depleted SOI dynamic threshold voltage MOS (DTMOS) for very low supply voltage applications (0.6 - 1 V); Comportement en dose cumulee de transistors DTMOS (MOS a tension de seuil dynamique) en technologie SOI partiellement desertee pour applications a tres basse tension d'alimentation (0.6 - 1 V)

    Energy Technology Data Exchange (ETDEWEB)

    Ferlet-Cavrois, V.; Musseau, O.; Leray, J.L. [CEA Bruyeres le Chatel, DRIF, 91 (France); Faynot, O.; Raynaud, C.; Pelloie, J.L. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique LETI, 38 (France)

    1999-07-01

    In this paper, we presented two DTMOS architectures processed with a partially depleted SOI technology. The first architecture, DTMOS without limiting transistor, is dedicated to ultra-low voltage applications, at 0.6 V. For 1V applications, the second architecture, DTMOS with limiting transistor, needs an additional transistor to limit the body-source diode current. The total dose irradiation of both DTMOS architectures induces no change of the drain current, but an increase of the body-source diode current. Total dose induced trapped charge in the buried oxide increases the body potential of the DTMOS transistor. It induces an increase of the current flow at the back interface of the silicon film. Irradiation of complex circuits using DTMOS transistors would lead to a degradation of the stand-by consumption. (authors)

  19. Papahanaumokuakea - Laysan Island Restoration 2010

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The Goal of the Laysan Island Restoration is to restore Laysan to a "Pristine" state which would require minimal monitoring and habitat for Endemic Endangered...

  20. Unbalanced Voltage Compensation in Low Voltage Residential AC Grids

    DEFF Research Database (Denmark)

    Trintis, Ionut; Douglass, Philip; Munk-Nielsen, Stig

    2016-01-01

    This paper describes the design and test of a control algorithm for active front-end rectifiers that draw power from a residential AC grid to feed heat pump loads. The control algorithm is able to control the phase to neutral or phase to phase RMS voltages at the point of common coupling....... The voltage control was evaluated with either active or reactive independent phase load current control. The control performance in field operation in a residential grid situated in Bornholm, Denmark was investigated for different use cases....

  1. Automated Voltage Control in LHCb

    CERN Document Server

    Granado Cardoso, L; Jacobsson, R

    2011-01-01

    LHCb is one of the 4 LHC experiments. In order to ensure the safety of the detector and to maximize efficiency, LHCb needs to coordinate its own operations, in particular the voltage configuration of the different subdetectors, according to the accelerator status. A control software has been developed for this purpose, based on the Finite State Machine toolkit and the SCADA system used for control throughout LHCb (and the other LHC experiments). This software permits to efficiently drive both the Low Voltage (LV) and High Voltage (HV) systems of the 10 different sub-detectors that constitute LHCb, setting each sub-system to the required voltage (easily configurable at run-time) based on the accelerator state. The control software is also responsible for monitoring the state of the Sub-detector voltages and adding it to the event data in the form of status-bits. Safe and yet flexible operation of the LHCb detector has been obtained and automatic actions, triggered by the state changes of the ...

  2. Low Actuation Voltage RF MEMS Switch Using Varying Section Composite Fixed-Fixed Beam

    Directory of Open Access Journals (Sweden)

    M. Manivannan

    2014-01-01

    Full Text Available The present authors have earlier reported the employment of varying section fixed-fixed beam for achieving lower pull-in voltage with marginal fall in restoring force. Reducing Young’s modulus also reduces the pull-in voltage but with lesser degree of reduction in restoring force. Composite beams are ideal alternatives to achieve decreased Young’s modulus. Hence new varying section composite fixed-fixed beam type RF MEMS switch has been proposed. The main advantage of this RF MEMS switch is that lower pull-in voltages can be achieved with marginal fall in stiction immunity. Spring constant of the proposed switch has been obtained using simulation studies and it has been shown that the spring constant and therefore the pull-in voltage (Vpi can be considerably reduced with the proposed switch. Simulation studies conducted on the proposed switch clearly demonstrate that the pull-in voltage can be reduced by 31.17% when compared to the varying section monolayer polysilicon fixed-fixed beam. Further this approach enables the designer to have more freedom to design lower pull-in voltage switches with improved stiction immunity.

  3. Active gate driver for dv/dt control and active voltage clamping in an IGBT stack

    DEFF Research Database (Denmark)

    Rasmussen, Tonny Wederberg

    2005-01-01

    For high voltages converters stacks of IGBTs can be used if the static and dynamic voltage sharing among the IGBTs can be applied. dVCE/dt should also be controlled in order not to damage insulation material. This paper describes theory and measurements of an active gate driver for stacking IGBTs...

  4. Adaptive wiener image restoration kernel

    Science.gov (United States)

    Yuan, Ding

    2007-06-05

    A method and device for restoration of electro-optical image data using an adaptive Wiener filter begins with constructing imaging system Optical Transfer Function, and the Fourier Transformations of the noise and the image. A spatial representation of the imaged object is restored by spatial convolution of the image using a Wiener restoration kernel.

  5. Development of a New Cascade Voltage-Doubler for Voltage Multiplication

    OpenAIRE

    Arash Toudeshki; Norman Mariun; Hashim Hizam; Noor Izzri Abdul Wahab

    2014-01-01

    For more than eight decades, cascade voltage-doubler circuits are used as a method to produce DC output voltage higher than the input voltage. In this paper, the topological developments of cascade voltage-doublers are reviewed. A new circuit configuration for cascade voltage-doubler is presented. This circuit can produce a higher value of the DC output voltage and better output quality compared to the conventional cascade voltage-doubler circuits, with the same number of stages.

  6. Simple buck/boost voltage regulator

    Science.gov (United States)

    Paulkovich, J.; Rodriguez, G. E.

    1980-01-01

    Circuit corrects low or high supply voltage, produces regulated output voltage. Circuit has fewer components because inductory/transformer combination and pulse-width modulator serve double duty. Regulator handles input voltage variation from as low as one half output voltage to as high as input transistor rating. Solar arrays, fuel cells, and thermionic generators might use this regulator.

  7. 30 CFR 18.47 - Voltage limitation.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Voltage limitation. 18.47 Section 18.47 Mineral... § 18.47 Voltage limitation. (a) A tool or switch held in the operator's hand or supported against his... particular voltage(s) are provided in the design and construction of the equipment, its wiring,...

  8. Cavity Voltage Phase Modulation MD

    CERN Document Server

    Mastoridis, Themistoklis; Molendijk, John; Timko, Helga; CERN. Geneva. ATS Department

    2016-01-01

    The LHC RF/LLRF system is currently configured for extremely stable RF voltage to minimize transient beam loading effects. The present scheme cannot be extended beyond nominal beam current since the demanded power would exceed the peak klystron power and lead to saturation. A new scheme has therefore been proposed: for beam currents above nominal (and possibly earlier), the cavity phase modulation by the beam will not be corrected (transient beam loading), but the strong RF feedback and One-Turn Delay feedback will still be active for loop and beam stability in physics. To achieve this, the voltage set point will be adapted for each bunch. The goal of this MD was to test a new algorithm that would adjust the voltage set point to achieve the cavity phase modulation that would minimize klystron forward power.

  9. Portable High Voltage Impulse Generator

    Directory of Open Access Journals (Sweden)

    S. Gómez

    2011-07-01

    Full Text Available This paper presents a portable high voltage impulse generator which was designed and built with insulation up to 20 kV. This design was based on previous work in which simulation software for standard waves was developed. Commercial components and low-cost components were used in this work; however, these particular elements are not generally used for high voltage applications. The impulse generators used in industry and laboratories are usually expensive; they are built to withstand extra high voltage and they are big, making them impossible to transport. The proposed generator is portable, thereby allowing tests to be made on devices that cannot be moved from their location. The results obtained with the proposed impulse generator were satisfactory in terms of time and waveforms compared to other commercial impulse generators and the standard impulse wave simulator.

  10. Wide Operational Range Processor Power Delivery Design for Both Super-Threshold Voltage and Near-Threshold Voltage Computing

    Institute of Scientific and Technical Information of China (English)

    Xin He; Gui-Hai Yan; Yin-He Han; Xiao-Wei Li

    2016-01-01

    The load power range of modern processors is greatly enlarged because many advanced power management techniques are employed, such as dynamic voltage frequency scaling, Turbo Boosting, and near-threshold voltage (NTV) technologies. However, because the efficiency of power delivery varies greatly with different load conditions, conventional power delivery designs cannot maintain high efficiency over the entire voltage spectrum, and the gained power saving may be offset by power loss in power delivery. We propose SuperRange, a wide operational range power delivery unit. SuperRange complements the power delivery capability of on-chip voltage regulator and off-chip voltage regulator. On top of SuperRange, we analyze its power conversion characteristics and propose a voltage regulator (VR) aware power management algorithm. Moreover, as more and more cores have been integrated on a singe chip, multiple SuperRange units can serve as basic building blocks to build, in a highly scalable way, more powerful power delivery subsystem with larger power capacity. Experimental results show SuperRange unit offers 1x and 1.3x higher power conversion efficiency (PCE) than other two conventional power delivery schemes at NTV region and exhibits an average 70%PCE over entire operational range. It also exhibits superior resilience to power-constrained systems.

  11. Restoring proximal caries lesions conservatively with tunnel restorations

    Directory of Open Access Journals (Sweden)

    Chu CH

    2013-07-01

    Full Text Available Chun-Hung Chu1, May L Mei,1 Chloe Cheung,1 Romesh P Nalliah2 1Faculty of Dentistry, The University of Hong Kong, Hong Kong, People's Republic of China; 2Department of Restorative Dentistry and Biomaterials Sciences, Harvard School of Dental Medicine, Boston, MA, USA Abstract: The tunnel restoration has been suggested as a conservative alternative to the conventional box preparation for treating proximal caries. The main advantage of tunnel restoration over the conventional box or slot preparation includes being more conservative and increasing tooth integrity and strength by preserving the marginal ridge. However, tunnel restoration is technique-sensitive and can be particularly challenging for inexperienced restorative dentists. Recent advances in technology, such as the contemporary design of dental handpieces with advanced light-emitting diode (LED and handheld comfort, offer operative dentists better vision, illumination, and maneuverability. The use of magnifying loupes also enhances the visibility of the preparation. The advent of digital radiographic imaging has improved dental imaging and reduced radiation. The new generation of restorative materials has improved mechanical properties. Tunnel restoration can be an option to restore proximal caries if the dentist performs proper case selection and pays attention to the details of the restorative procedures. This paper describes the clinical technique of tunnel restoration and reviews the studies of tunnel restorations. Keywords: operative, practice, tunnel preparation, composite, amalgam, glass ionomer

  12. Relativistic Linear Restoring Force

    Science.gov (United States)

    Clark, D.; Franklin, J.; Mann, N.

    2012-01-01

    We consider two different forms for a relativistic version of a linear restoring force. The pair comes from taking Hooke's law to be the force appearing on the right-hand side of the relativistic expressions: d"p"/d"t" or d"p"/d["tau"]. Either formulation recovers Hooke's law in the non-relativistic limit. In addition to these two forces, we…

  13. What Turns Assistive into Restorative Brain-Machine Interfaces?

    Science.gov (United States)

    Gharabaghi, Alireza

    2016-01-01

    Brain-machine interfaces (BMI) may support motor impaired patients during activities of daily living by controlling external devices such as prostheses (assistive BMI). Moreover, BMIs are applied in conjunction with robotic orthoses for rehabilitation of lost motor function via neurofeedback training (restorative BMI). Using assistive BMI in a rehabilitation context does not automatically turn them into restorative devices. This perspective article suggests key features of restorative BMI and provides the supporting evidence: In summary, BMI may be referred to as restorative tools when demonstrating subsequently (i) operant learning and progressive evolution of specific brain states/dynamics, (ii) correlated modulations of functional networks related to the therapeutic goal, (iii) subsequent improvement in a specific task, and (iv) an explicit correlation between the modulated brain dynamics and the achieved behavioral gains. Such findings would provide the rationale for translating BMI-based interventions into clinical settings for reinforcement learning and motor rehabilitation following stroke. PMID:27790085

  14. What turns assistive into restorative brain-machine interfaces?

    Directory of Open Access Journals (Sweden)

    Alireza Gharabaghi

    2016-10-01

    Full Text Available Brain-machine interfaces (BMI may support motor impaired patients during activities of daily living by controlling external devices such as prostheses (assistive BMI. Moreover, BMIs are applied in conjunction with robotic orthoses for rehabilitation of lost motor function via neurofeedback training (restorative BMI. Using assistive BMI in a rehabilitation context does not automatically turn them into restorative devices. This perspective article suggests key features of restorative BMI and provides the supporting evidence:In summary, BMI may be referred to as restorative tools when demonstrating subsequently (i operant learning and progressive evolution of specific brain states/dynamics, (ii correlated modulations of functional networks related to the therapeutic goal, (iii subsequent improvement in a specific task, and (iv an explicit correlation between the modulated brain dynamics and the achieved behavioral gains. Such findings would provide the rationale for translating BMI-based interventions into clinical settings for reinforcement learning and motor rehabilitation following stroke.

  15. A low voltage CMOS low drop-out voltage regulator

    Science.gov (United States)

    Bakr, Salma Ali; Abbasi, Tanvir Ahmad; Abbasi, Mohammas Suhaib; Aldessouky, Mohamed Samir; Abbasi, Mohammad Usaid

    2009-05-01

    A low voltage implementation of a CMOS Low Drop-Out voltage regulator (LDO) is presented. The requirement of low voltage devices is crucial for portable devices that require extensive computations in a low power environment. The LDO is implemented in 90nm generic CMOS technology. It generates a fixed 0.8V from a 2.5V supply which on discharging goes to 1V. The buffer stage used is unity gain configured unbuffered OpAmp with rail-to-rail swing input stage. The simulation result shows that the implemented circuit provides load regulation of 0.004%/mA and line regulation of -11.09mV/V. The LDO provides full load transient response with a settling time of 5.2μs. Further, the dropout voltage is 200mV and the quiescent current through the pass transistor (Iload=0) is 20μA. The total power consumption of this LDO (excluding bandgap reference) is only 80μW.

  16. The high voltage homopolar generator

    Science.gov (United States)

    Price, J. H.; Gully, J. H.; Driga, M. D.

    1986-11-01

    System and component design features of proposed high voltage homopolar generator (HVHPG) are described. The system is to have an open circuit voltage of 500 V, a peak output current of 500 kA, 3.25 MJ of stored inertial energy and possess an average magnetic-flux density of 5 T. Stator assembly components are discussed, including the stator, mount structure, hydrostatic bearings, main and motoring brushgears and rotor. Planned operational procedures such as monitoring the rotor to full speed and operation with a superconducting field coil are delineated.

  17. Coordinated Control of Voltage Ride Through for DFIG Wind Turbine Systems Using Energy-based DVR%基于储能型DVR的双馈风电机组电压穿越协调控制

    Institute of Scientific and Technical Information of China (English)

    许建兵; 江全元; 石庆均

    2013-01-01

    针对双馈感应发电机(DFIG),提出了一种基于超级电容器(SC)储能的动态电压调节器(DVR)实现电压穿越的协调控制策略.在电网电压故障时,基于SC的DVR对DFIG端口电压进行完全补偿,使得DFIG端口电压始终维持在正常水平;并通过DFIG和基于SC的DVR协调控制,减少DFIG在故障期间输出的有功功率,从而减少故障期间所需的DVR功率和容量.在MATLAB/Simulink环境下搭建仿真模型,分别进行了对称和不对称故障下的零电压穿越、低电压穿越和高电压穿越仿真.仿真结果证明了所提出的协调控制策略的有效性.%A coordinated control strategy, which uses super capacitor (SC)-based dynamic voltage restorer (DVR) , is proposed to improve the voltage ride through capability of doubly-fed induction generators (DFIGs).The voltage level of DFIG stator is fully compensated by SC-based DVR during grid faults.The active power of DFIG is deceased by the coordinated control to minimise the power rating of DVR.A simulation model is established in MATLAB/Simulink.Zero voltage ride through, low voltage ride through and high voltage ride through during symmetrical and asymmetrical grid faults are simulated respectively.The validity of the proposed coordinate control strategy is verified by the simulation results.

  18. Voltage synchronizations between multichannel electroencephalograms during epileptic seizures

    CERN Document Server

    Tuncay, Caglar

    2010-01-01

    The underlying dynamics for the electroencephalographic (EEG) recordings from humans but especially epilepsy patients are usually not completely known. However, the ictal activity is claimed to be characterized by synchronous oscillations in the brain voltages in the literature. These time dependent interdependencies (synchronization, coupling) between the EEG voltages from epileptogenic and non epileptogenic brain sites of nineteen focal epileptic patients are investigated in this work. It is found that strong synchronizationdesynchronization events occur in alternation during most of the investigated seizures. Thus, these seizures are detected with considerable sensitivity (71 of the 79 seizures).

  19. Resilient architecture design for voltage variation

    CERN Document Server

    Reddi, Vijay Janapa

    2013-01-01

    Shrinking feature size and diminishing supply voltage are making circuits sensitive to supply voltage fluctuations within the microprocessor, caused by normal workload activity changes. If left unattended, voltage fluctuations can lead to timing violations or even transistor lifetime issues that degrade processor robustness. Mechanisms that learn to tolerate, avoid, and eliminate voltage fluctuations based on program and microarchitectural events can help steer the processor clear of danger, thus enabling tighter voltage margins that improve performance or lower power consumption. We describe

  20. River restoration: morphological, hydrological, biogeochemical and ecological changes and challenges

    Directory of Open Access Journals (Sweden)

    M. Schirmer

    2013-08-01

    Full Text Available River restoration is essential as a means to enhance river dynamics, environmental heterogeneity and biodiversity. The underlying processes governing the dynamic changes need to be understood thoroughly to ensure that restoration projects meet their goals. In particular, we need to understand quantitatively how hydromorphological variability relates to ecosystem functioning and services, biodiversity and (groundwater quality in restored river corridors. Here, we provide a short overview on the literature and present a study of a restored river corridor in Switzerland combining physical, chemical, and biological observations with modeling. The results show complex spatial patterns of bank infiltration, habitat-type, biotic communities and biogeochemical processes. In particular, we found an increase in taxonomic and functional diversity for earthworms, testate amoebae and bacteria in the restored part of the river. This complexity is driven by river hydrology and morphodynamics, which are in turn actively coupled to riparian vegetation processes. Given this complexity and the multiple constraints on the uses and management of floodplains, a multi-disciplinary approach is needed to monitor the success of restoration measures and to make recommendations for future restoration projects.

  1. Stability and Restoration phenomena in Competitive Systems

    CERN Document Server

    Uechi, Lisa

    2012-01-01

    A conservation law and stability, recovering phenomena and characteristic patterns of a nonlinear dynamical system have been studied and applied to biological and ecological systems. In our previous study, we proposed a system of symmetric 2n-dimensional conserved nonlinear differential equations with external perturbations. In this paper, competitive systems described by 2-dimensional nonlinear dynamical (ND) model with external perturbations are applied to population cycles and recovering phenomena of systems from microbes to mammals. The famous 10-year cycle of population density of Canadian lynx and snowshoe hare is numerically analyzed. We find that a nonlinear dynamical system with a conservation law is stable and generates a characteristic rhythm (cycle) of population density, which we call the {\\it standard rhythm} of a nonlinear dynamical system. The stability and restoration phenomena are strongly related to a conservation law and balance of a system. The {\\it standard rhythm} of population density ...

  2. Bulk Restoration for SDN-Based Transport Network

    Directory of Open Access Journals (Sweden)

    Yang Zhao

    2016-01-01

    Full Text Available We propose a bulk restoration scheme for software defined networking- (SDN- based transport network. To enhance the network survivability and improve the throughput, we allow disrupted flows to be recovered synchronously in dynamic order. In addition backup paths are scheduled globally by applying the principles of load balance. We model the bulk restoration problem using a mixed integer linear programming (MILP formulation. Then, a heuristic algorithm is devised. The proposed algorithm is verified by simulation and the results are analyzed comparing with sequential restoration schemes.

  3. Dynamics

    CERN Document Server

    Goodman, Lawrence E

    2001-01-01

    Beginning text presents complete theoretical treatment of mechanical model systems and deals with technological applications. Topics include introduction to calculus of vectors, particle motion, dynamics of particle systems and plane rigid bodies, technical applications in plane motions, theory of mechanical vibrations, and more. Exercises and answers appear in each chapter.

  4. A new low-voltage and high-speed sense amplifier for flash memory

    Institute of Scientific and Technical Information of China (English)

    Guo Jiarong; Ran Feng

    2011-01-01

    A new low-voltage and high-speed sense amplifier is presented,based on a very simple direct currentmode comparison.It adopts low-voltage reference current extraction and a dynamic output method to realize its performance indicators such as low voltage,low power and high precision.The proposed amplifier can sense a 0.5 μA current gap and work with a lowest voltage of 1 V.In addition,the current power of a single amplifier is optimized by 15%.

  5. Wind Power Plant Voltage Control Optimization with Embedded Application of Wind Turbines and Statcom

    DEFF Research Database (Denmark)

    Wu, Qiuwei; Solanas, Jose Ignacio Busca; Zhao, Haoran

    2017-01-01

    Increasing wind power penetration and the size of wind power plants (WPPs) brings challenges to the operation and control of power systems. Most of WPPs are located far from load centers and the short circuit ratio at the point of common coupling (PCC) is low. The fluctuations of wind power...... will cause voltage variations. An optimal voltage control scheme for WPPs with STATCOMs is presented in the paper. It ensures that the voltages within the WPPs and at the high voltage side of the WPPs are within the limits and maximizes the dynamic Var reserve of the WPPs. Case studies were conducted...

  6. Distributed Low Voltage Ride-Through Operation of Power Converters in Grid-Connected Microgrids under Voltage Sags

    DEFF Research Database (Denmark)

    Zhao, Xin; Meng, Lexuan; Dragicevic, Tomislav;

    2015-01-01

    the voltage in all phases at AC common bus. However, since the line admittances from each converter to point of common coupling (PCC) are not identical, the injected reactive power may not be equally shared. In order to achieve low voltage ride through (LVRT) capability along with a good power sharing...... accuracy, a hierarchical control strategy is proposed in this paper. Droop control and virtual impedance is applied in primary control loop while secondary control loop is based on dynamic consensus algorithm (DCA). Experiments are conducted to verify the effectiveness of the proposed control strategy....

  7. VOLTAGE REGULATORS OF SYNCHRONOUS GENERATORS

    Directory of Open Access Journals (Sweden)

    Grigorash O. V.

    2015-06-01

    Full Text Available Synchronous generators are the primary source of electrical power autonomous electrosupply systems, including backup systems. They are also used in a structure of rotating electricity converters and are widely used in renewable energy as part of wind power plants of small, mini and micro hydroelectric plants. Increasing the speed and the accuracy of the system of the voltage regulation of synchronous generators is possible due to the development of combined systems containing more stabilizers. The article illustrates the functional schemes of circuit voltage stabilizers and frequency synchronous generators (with electromagnetic excitation and permanent magnet excitation and describes the features of their work, including two and three-aggregate rotating converters of electricity used in uninterruptible power supply systems. To improve the technical characteristics of the system of stabilization we have proposed functional solutions for stabilizers of synchronous generators made on the base of direct frequency converters and using a transformer with a rotating magnetic field. To improve the reliability of and to improve the operational characteristics of the autonomous independent sources of electricity we suggest creating the main functional blocks and the elements of the stabilization system in a modular way. The functional circuit solutions of voltage regulators of synchronous generators and the characteristics of their work considered in the article, are able to improve the efficiency of pre-design work in the development of new technical solutions for stabilizing the voltage and the frequency in synchronous generators of electrosupply autonomous systems

  8. Frequency-controlled voltage regulator

    Science.gov (United States)

    Mclyman, W. T.

    1980-01-01

    Converting input ac to higher frequency reduce size and weight and makes possible unique kind of regulation. Since conversion frequency is above range of human hearing, supply generated on audible noise. It also exploits highfrequency conversion features to regulate its output voltage in novel way. Circuit is inherently short-circuit proof.

  9. Controlled operation of the Islanded portion of the CIGRE Low Voltage distribution network

    DEFF Research Database (Denmark)

    Mustafa, Ghullam; Bak-Jensen, Birgitte; Bak, Claus Leth;

    2017-01-01

    be switched to the Voltage-Frequency (VF) control mode. In case of islanding, the network loses it slack reference and this reference is established by the use of VF controller. The voltage and the frequency of the islanded MG deviate when it is disconnected from the transmission grid and these deviations...... are according to the load-generation imbalance in the islanded MG. The voltage and the frequency of the islanded MG can be restored to the permissible limits if the desired/exceeded amount of active and reactive power is injected/absorbed by the locally available sources in islanded MG. This paper proposes...... the control strategy which can compensate the problems of the voltage and the frequency deviations in the islanded MG. The selection of the VF controller for the most suitable DG unit of the LV test network is also presented in this paper and effectiveness of the controllers is verified by presenting...

  10. A dulal-functional medium voltage level DVR to limit downstream fault currents

    DEFF Research Database (Denmark)

    Li, Yun Wei; Vilathgamuwa, D. Mahinda; Loh, Poh Chiang

    2007-01-01

    , the DVR will therefore be tasked to mitigate even more faults involving downstream loads. Large fault currents would flow through the DVR during a downstream fault before the opening of a circuit breaker. This will cause the voltage at point of common coupling (PCC) to drop, which would affect the loads...... on the other parallel feeders connected to PCC. Furthermore, if not controlled properly, the DVR might also contribute to this PCC voltage sag in the process of compensating the missing voltage, thus further worsening the fault situation. To limit the flow of large line currents, and therefore restore the PCC...... voltage as well as protect the DVR system components, a downstream fault limiting function is proposed and integrated in the DVR operation. A flux-charge-model feedback algorithm is implemented so that the DVR would act as a large virtual inductance in series with the distribution feeder in fault...

  11. Voltage-gated Proton Channels

    Science.gov (United States)

    DeCoursey, Thomas E.

    2014-01-01

    Voltage-gated proton channels, HV1, have vaulted from the realm of the esoteric into the forefront of a central question facing ion channel biophysicists, namely the mechanism by which voltage-dependent gating occurs. This transformation is the result of several factors. Identification of the gene in 2006 revealed that proton channels are homologues of the voltage-sensing domain of most other voltage-gated ion channels. Unique, or at least eccentric, properties of proton channels include dimeric architecture with dual conduction pathways, perfect proton selectivity, a single-channel conductance ~103 smaller than most ion channels, voltage-dependent gating that is strongly modulated by the pH gradient, ΔpH, and potent inhibition by Zn2+ (in many species) but an absence of other potent inhibitors. The recent identification of HV1 in three unicellular marine plankton species has dramatically expanded the phylogenetic family tree. Interest in proton channels in their own right has increased as important physiological roles have been identified in many cells. Proton channels trigger the bioluminescent flash of dinoflagellates, facilitate calcification by coccolithophores, regulate pH-dependent processes in eggs and sperm during fertilization, secrete acid to control the pH of airway fluids, facilitate histamine secretion by basophils, and play a signaling role in facilitating B-cell receptor mediated responses in B lymphocytes. The most elaborate and best-established functions occur in phagocytes, where proton channels optimize the activity of NADPH oxidase, an important producer of reactive oxygen species. Proton efflux mediated by HV1 balances the charge translocated across the membrane by electrons through NADPH oxidase, minimizes changes in cytoplasmic and phagosomal pH, limits osmotic swelling of the phagosome, and provides substrate H+ for the production of H2O2 and HOCl, reactive oxygen species crucial to killing pathogens. PMID:23798303

  12. Application of SMES in wind farm to improve voltage stability

    Science.gov (United States)

    Shi, J.; Tang, Y. J.; Ren, L.; Li, J. D.; Chen, S. J.

    2008-09-01

    For the wind farms introducing doubly fed induction generators (DFIGs), voltage stability is an essential issue which influences their widely integration into the power grid. This paper proposes the application of superconducting magnetic energy storage (SMES) in the power system integrated with wind farms. SMES can control the active and reactive power flow, realizing the operation in four quadrants independently. The introducing of SMES can smooth the output power flow of the wind farms, and supply dynamic voltage support. Using MATLAB/SIMULINK, the models of the DFIG, the power grid connected and the SMES are created. Simulation results show that the voltage stability of the power system integrated with wind farms can be improved considerably.

  13. Design techniques for low-voltage analog integrated circuits

    Science.gov (United States)

    Rakús, Matej; Stopjaková, Viera; Arbet, Daniel

    2017-08-01

    In this paper, a review and analysis of different design techniques for (ultra) low-voltage integrated circuits (IC) are performed. This analysis shows that the most suitable design methods for low-voltage analog IC design in a standard CMOS process include techniques using bulk-driven MOS transistors, dynamic threshold MOS transistors and MOS transistors operating in weak or moderate inversion regions. The main advantage of such techniques is that there is no need for any modification of standard CMOS structure or process. Basic circuit building blocks like differential amplifiers or current mirrors designed using these approaches are able to operate with the power supply voltage of 600 mV (or even lower), which is the key feature towards integrated systems for modern portable applications.

  14. Improving Low Voltage Ride Through Capability of Wind Farm Grid-Connected via Dynamic Chopper Controlled Breaking Resistor Based MMC-HVDC Transmission System%含动态直流泄能电阻的MMC-HVDC提高风电场低电压穿越能力研究

    Institute of Scientific and Technical Information of China (English)

    李文津; 汤广福; 康勇

    2014-01-01

    提出了基于动态直流泄能电阻的模块化多电平柔性输电直流方案,以提高基于感应双馈电机风电场的低电压穿越能力。基于矢量控制及无源电压跟随控制分别设计了系统侧、风场侧柔性直流换流器在风电场稳态运行时的控制策略。当交流系统故障导致电压跌落时,详细分析了动态直流泄能电阻的工作原理、动作判据及导通持续时间,以实现风电场低电压穿越;同时研究了其与系统侧模块化多电平换流器在故障清除后电压恢复期的协调控制,以快速恢复风电场有功输出能力。仿真结果表明:当交流系统故障时,含动态直流泄能电阻的柔性直流输电系统能够维持直流电压且不改变风电场输出电压电流;当故障清除后,风电场输出功率恢复速率远大于电力系统行业标准相关技术指标。%A modular multilevel voltage sourced converter-based HVDC (MMC-HVDC) power transmission scheme based on dynamic chopper controlled breaking resistor (DCCBR) is proposed to improve the low-voltage ride through (LVRT) capability of wind farm composed of doubly fed induction generators (DFIG). Based on vector control and network voltage tracing control the control strategies for grid side modular multilevel converter (GSMMC) and wind farm side modular multilevel converter (WFMMC) under steady state operation of wind farm are designed respectively. Under voltage sag caused by fault in AC power grid, the working principle, operating criterion and turn-on duration time of DCCBR are analyzed in depth to realize LVRT of wind farm;meanwhile, to recover the active power output capability of wind farm rapidly the coordinated control for DCCBR and GSMMC during the voltage recovery after clearing of the fault is researched. Simulation results show that during the fault in AC power grid the flexible HVDC transmission system containing DCCBR can maintain the DC voltage of HVDC system while

  15. Short-Term State Forecasting-Based Optimal Voltage Regulation in Distribution Systems: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Rui; Jiang, Huaiguang; Zhang, Yingchen

    2017-05-17

    A novel short-term state forecasting-based optimal power flow (OPF) approach for distribution system voltage regulation is proposed in this paper. An extreme learning machine (ELM) based state forecaster is developed to accurately predict system states (voltage magnitudes and angles) in the near future. Based on the forecast system states, a dynamically weighted three-phase AC OPF problem is formulated to minimize the voltage violations with higher penalization on buses which are forecast to have higher voltage violations in the near future. By solving the proposed OPF problem, the controllable resources in the system are optimally coordinated to alleviate the potential severe voltage violations and improve the overall voltage profile. The proposed approach has been tested in a 12-bus distribution system and simulation results are presented to demonstrate the performance of the proposed approach.

  16. Process-based principles for restoring river ecosystems

    Science.gov (United States)

    Beechie, T. J.

    2010-12-01

    Process-based restoration aims to re-establish normative rates and magnitudes of physical, chemical, and biological processes that sustain river and floodplain ecosystems. Ecosystem conditions at any site are governed by hierarchical regional, watershed, and reach-scale processes controlling hydrologic and sediment regimes, floodplain and aquatic habitat dynamics, and riparian and aquatic biota. To help guide river restoration toward sustainable actions, we outline and illustrate four process-based principles that ensure actions: (1) address root causes of degradation, (2) are consistent with the physical and biological potential of the site, (3) are at a scale commensurate with environmental problems, and (4) have clearly articulated expected outcomes for ecosystem dynamics. Applying these principles will help avoid common pitfalls in river restoration, such as creating habitat types that are outside the range of a site’s natural potential, attempting to build static habitats in dynamic environments, or constructing habitat features that are ultimately overwhelmed by untreated system drivers.

  17. Vector spin modeling for magnetic tunnel junctions with voltage dependent effects

    Energy Technology Data Exchange (ETDEWEB)

    Manipatruni, Sasikanth, E-mail: sasikanth.manipatruni@intel.com; Nikonov, Dmitri E.; Young, Ian A. [Exploratory Integrated Circuits, Components Research, Intel Corp., Hillsboro, Oregon 97124 (United States)

    2014-05-07

    Integration and co-design of CMOS and spin transfer devices requires accurate vector spin conduction modeling of magnetic tunnel junction (MTJ) devices. A physically realistic model of the MTJ should comprehend the spin torque dynamics of nanomagnet interacting with an injected vector spin current and the voltage dependent spin torque. Vector spin modeling allows for calculation of 3 component spin currents and potentials along with the charge currents/potentials in non-collinear magnetic systems. Here, we show 4-component vector spin conduction modeling of magnetic tunnel junction devices coupled with spin transfer torque in the nanomagnet. Nanomagnet dynamics, voltage dependent spin transport, and thermal noise are comprehended in a self-consistent fashion. We show comparison of the model with experimental magnetoresistance (MR) of MTJs and voltage degradation of MR with voltage. Proposed model enables MTJ circuit design that comprehends voltage dependent spin torque effects, switching error rates, spin degradation, and back hopping effects.

  18. Wetland Microbial Community Response to Restoration

    Science.gov (United States)

    Theroux, S.; Hartman, W.; Tringe, S. G.

    2015-12-01

    Wetland restoration has been proposed as a potential long-term carbon storage solution, with a goal of engineering geochemical dynamics to accelerate peat accretion and encourage greenhouse gas (GHG) sequestration. However, wetland microbial community composition and metabolic rates are poorly understood and their predicted response to wetland restoration is a veritable unknown. In an effort to better understand the underlying factors that shape the balance of carbon flux in wetland soils, we targeted the microbial communities along a salinity gradient ranging from freshwater tidal marshes to hypersaline ponds in the San Francisco Bay-Delta region. Using 16S rRNA gene sequencing and shotgun metagenomics, coupled with greenhouse gas measurements, we sampled sixteen sites capturing a range in salinity and restoration status. Seawater delivers sulfate to wetland ecosystems, encouraging sulfate reduction and discouraging methane production. As expected, we observed the highest rates of methane production in the freshwater wetlands. Recently restored wetlands had significantly higher rates of methane production compared to their historic counterparts that could be attributed to variations in trace metal and organic carbon content in younger wetlands. In contrast, our sequencing results revealed an almost immediate return of the indigenous microbial communities following seasonal flooding and full tidal restoration in saline and hypersaline wetlands and managed ponds. Notably, we found elevated methane production rates in hypersaline ponds, the result of methylotrophic methane production confirmed by sequence data and lab incubations. Our study links belowground microbial communities and their aboveground greenhouse gas production and highlights the inherent complexity in predicting wetland microbial response in the face of both natural and unnatural disturbances.

  19. Control of ion energy and angular distributions using voltage waveform

    Energy Technology Data Exchange (ETDEWEB)

    Rauf, S.

    1999-07-01

    A number of plasma-aided microelectronics manufacturing processes sensitively depend on the ion characteristics at the substrate, in particular the ion energy (IEDF) and angular (IADF) distribution functions. The outcome of these processes can be much more precisely controlled if one has direct control over the IEDFs and IADFs. Past studies have explored the influence of rb bias voltage amplitude and frequency, inductive power deposition and gas pressure on the ion characteristics at the substrate. The factor that influences the ion dynamics most is however the time-dependent sheath voltage and, as demonstrated in this paper, sheath voltage can be accurately controlled using the rf bias voltage waveform. In this paper, the authors computationally examine the influence of the rf bias voltage waveform on the IEDFs and IADFs at the substrate in an inductively coupled plasma (ICP) reactor. This study has been conducted using a coupled set of the Hybrid Plasma Equipment Model (HPEM) and a circuit model, and the Plasma Chemistry Monte Carlo Simulation (PCMCS).

  20. Over-voltage protection system and method

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Song; Dong, Dong; Lai, Rixin

    2017-05-02

    An over-voltage protection system includes an electronic valve connected across two terminals of a circuit and an over-voltage detection circuit connected across one of the plurality of semiconductor devices for detecting an over-voltage across the circuit. The electronic valve includes a plurality of semiconductor devices connected in series. The over-voltage detection circuit includes a voltage divider circuit connected to a break-over diode in a way to provide a representative low voltage to the break-over diode and an optocoupler configured to receive a current from the break-over diode when the representative low voltage exceeds a threshold voltage of the break-over diode indicating an over-voltage condition. The representative low voltage provided to the break-over diode represents a voltage across the one semiconductor device. A plurality of self-powered gate drive circuits are connected to the plurality of semiconductor devices, wherein the plurality of self-powered gate drive circuits receive over-voltage triggering pulses from the optocoupler during the over-voltage condition and switch on the plurality of semiconductor devices to bypass the circuit.

  1. Longevity of silicate ceramic restorations.

    Science.gov (United States)

    Beier, Ulrike Stephanie; Dumfahrt, Herbert

    2014-09-01

    The demand for esthetic restorations has resulted in an increased use of dental ceramics as a biocompatible and functionally sufficient alternative to conventional restorative materials. Silicate ceramic restorations are widely used for veneers, inlays, onlays, and crowns in dentistry. Long-term data are of crucial importance to optimize clinical practice. The purpose of the present article is to summarize data of the Innsbruck ceramic evaluation up to 261 months with the focus on longevity and failure characteristics.

  2. Advances in high voltage engineering

    CERN Document Server

    Haddad, A

    2005-01-01

    This book addresses the very latest research and development issues in high voltage technology and is intended as a reference source for researchers and students in the field, specifically covering developments throughout the past decade. This unique blend of expert authors and comprehensive subject coverage means that this book is ideally suited as a reference source for engineers and academics in the field for years to come.

  3. High Voltage Pulse Testing Survey.

    Science.gov (United States)

    1985-10-01

    Cryogenic 23 E. Liquids 26 F. Solids 28 1. Polyethylene 28 2. Cross-Linked Polyethylene ( XLPE ) 29 3. Polyimide and Polyvenylchloride (PVC) 31 VI Benefits 35 A...Strength of XLPE Cables 29 vii * 4" I PROGRAM OBJECTIVES The Pulse Test Survey summarizes government, industry, and technical reports on high voltage pulse...system of silicone oil on a XLPE (cross-linked polyethylene) spacer tends to lower the impulse breakdown by approximately 10 percent. The negative impulse

  4. TRANSISTOR HIGH VOLTAGE POWER SUPPLY

    Science.gov (United States)

    Driver, G.E.

    1958-07-15

    High voltage, direct current power supplies are described for use with battery powered nuclear detection equipment. The particular advantages of the power supply described, are increased efficiency and reduced size and welght brought about by the use of transistors in the circuit. An important feature resides tn the employment of a pair of transistors in an alternatefiring oscillator circuit having a coupling transformer and other circuit components which are used for interconnecting the various electrodes of the transistors.

  5. Modeling and Design of DC Boost and AC Side Voltage Controllers in Asymmetrical Γ-Source Inverter

    OpenAIRE

    2014-01-01

    In this paper a control system is proposed to simultaneously control the voltage boost and output voltage of assymetrical Γ-Source Inverters. Dynamic model of the system is used to design the controllers. Voltage boost on assymetrical Γ-Source Inverters is done by voltage control of impedance network capacitor and the regulation of inverter shoot through duty cycle. Since the stability margin of the system is low due to the right half plane zero in its dynamic model, the design of fast contro...

  6. Low voltage electron beam accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Ochi, Masafumi [Iwasaki Electric Co., Ltd., Tokyo (Japan)

    2003-02-01

    Widely used electron accelerators in industries are the electron beams with acceleration voltage at 300 kV or less. The typical examples are shown on manufactures in Japan, equipment configuration, operation, determination of process parameters, and basic maintenance requirement of the electron beam processors. New electron beam processors with acceleration voltage around 100 kV were introduced maintaining the relatively high dose speed capability of around 10,000 kGy x mpm at production by ESI (Energy Science Inc. USA, Iwasaki Electric Group). The application field like printing and coating for packaging requires treating thickness of 30 micron or less. It does not require high voltage over 110 kV. Also recently developed is a miniature bulb type electron beam tube with energy less than 60 kV. The new application area for this new electron beam tube is being searched. The drive force of this technology to spread in the industries would be further development of new application, process and market as well as the price reduction of the equipment, upon which further acknowledgement and acceptance of the technology to societies and industries would entirely depend. (Y. Tanaka)

  7. Technologies for lake restoration

    Directory of Open Access Journals (Sweden)

    Helmut KLAPPER

    2003-09-01

    Full Text Available Lakes are suffering from different stress factors and need to be restored using different approaches. The eutrophication remains as the main water quality management problem for inland waters: both lakes and reservoirs. The way to curb the degradation is to stop the nutrient sources and to accelerate the restoration with help of in-lake technologies. Especially lakes with a long retention time need (eco- technological help to decrease the nutrient content in the free water. The microbial and other organic matter from sewage and other autochthonous biomasses, causes oxygen depletion, which has many adverse effects. In less developed countries big reservoirs function as sewage treatment plants. Natural aeration solves problems only partly and many pollutants tend to accumulate in the sediments. The acidification by acid rain and by pyrite oxidation has to be controlled by acid neutralizing technologies. Addition of alkaline chemicals is useful only for soft waters, and technologies for (microbial alkalinization of very acidic hardwater mining lakes are in development. The corrective measures differ from those in use for eutrophication control. The salinization and water shortage mostly occurs if more water is used than available. L. Aral, L. Tschad, the Dead Sea or L. Nasser belong to waters with most severe environmental problems on a global scale. Their hydrologic regime needs to be evaluated. The inflow of salt water at the bottom of some mining lakes adds to stability of stratification, and thus accumulation of hydrogen sulphide in the monimolimnion of the meromictic lakes. Destratification, which is the most used technology, is only restricted applicable because of the dangerous concentrations of the byproducts of biological degradation. The contamination of lakes with hazardous substances from industry and agriculture require different restoration technologies, including subhydric isolation and storage, addition of nutrients for better self

  8. Piezo Voltage Controlled Planar Hall Effect Devices

    OpenAIRE

    Bao Zhang; Kang-Kang Meng; Mei-Yin Yang; Edmonds, K. W.; Hao Zhang; Kai-Ming Cai; Yu Sheng; Nan Zhang; Yang Ji; Jian-Hua Zhao; Hou-Zhi Zheng; Kai-You Wang

    2015-01-01

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the pie...

  9. The development and outlook of the medium-voltage dynamic reactive power compensation device in China%我国中压动态无功补偿装置的发展及展望

    Institute of Scientific and Technical Information of China (English)

    方欢欢; 舒欣梅; 陈彬

    2012-01-01

    Talking about the necessary of reactive power compensation for a start to this paper, introduce the principle of reactive power compensation device and analysis of the advantages and disadvantages of the common reactive power compensation devices, then, the present research status of reactive power compensation devices in China and abroad are introduced. Moreover discuss the new technologies applied in the SVC device and analysis of reactive power compensation device in power capacitors, control programs and switching components, finally, intelligent SVC as the development direction of the medium-voltage reactive power compensation device to look into the distance.%从无功补偿装置应用的必要性出发,介绍了无功补偿装置的原理及组成,分析了常见无功补偿装置的优缺点,论述了国内外无功补偿装置的应用现状.着重介绍了新技术在SVC装置中应用,对比分析了无功补偿装置中的电力电容器、控制方案和投切元件,最后展望了智能型SVC的广泛应用是中压无功补偿装置的发展方向.

  10. The economics of restoration: looking back and leaping forward.

    Science.gov (United States)

    Blignaut, James; Aronson, James; de Wit, Martin

    2014-08-01

    Since the publication of the Millennium Ecosystem Assessment in 2005 there has been a surge of interest in ecological restoration (ER) to recover biodiversity, re-establish ecosystem functioning and connectivity, and reactivate the delivery of ecosystem services. In policy spheres, there have also been repeated calls for expansion of restoration efforts. In many countries, new legislation now requires some form of restoration and/or a form of offset investment. All of this will require major increases in financial allocations toward restoration science, technology, and implementation, and much more detailed valuation techniques. The economics of restoration is a new field emerging to support these needs. Our paper here starts with an analysis of the articles and reviews published on this broad subject from 1928 to 2012, as captured in the Scopus academic search platform. Our goal is to present and summarize what has been said and done in this area to date. Next, we map out one possible way forward, illustrated by examples and based on a coherent bundle of decision parameters related to the economics of ER and, more broadly, to the restoration of natural capital. The restoration of natural capital is defined as activities that integrate investment in, and replenishment of, natural capital stocks to improve the flows of ecosystem goods and services, and the preservation of biodiversity, while enhancing all aspects of human well-being. We give special attention to system dynamic approaches and other promising tools and techniques.

  11. Voltage Control for Unbalanced Low Voltage Grids Using a Decoupled-Phase On-Load Tap-Changer Transformer and Photovoltaic Inverters

    OpenAIRE

    Zecchino, Antonio; Marinelli, Mattia; Hu, Junjie; Coppo, Massimiliano; Turri, Roberto

    2015-01-01

    This paper presents modeling and analysis of the potential benefits of joint actions of a MV/LV three-phase power distribution transformer with independent on-load tap-changer control on each phase and photovoltaic inverters provided with reactive power control capability, in terms of accommodating more renewable generations in the LV grid. The potential benefits are investigated in terms of voltage unbalance reduction and local voltage regulation. 24-hours root-mean-square dynamics simulatio...

  12. Voltage Control for Unbalanced Low Voltage Grids Using a Decoupled-Phase On-Load Tap-Changer Transformer and Photovoltaic Inverters

    DEFF Research Database (Denmark)

    Zecchino, Antonio; Marinelli, Mattia; Hu, Junjie

    2015-01-01

    more renewable generations in the LV grid. The potential benefits are investigated in terms of voltage unbalance reduction and local voltage regulation. 24-hours root-mean-square dynamics simulation studies have been carried out with timestep of 1 second using 10-mins resolution consumption...... and production profiles. A totally passive real Danish low voltage distribution network is used for the grid topology as well as for the characterization of loads profiles, while the production ones are empirically defined under assumptions in scenarios with different level of photovoltaic penetration and grade...

  13. Skjern River Restoration Counterfactual

    DEFF Research Database (Denmark)

    Clemmensen, Thomas Juel

    2014-01-01

    In 2003 the Skjern River Restoration Project in Denmark was awarded the prestigious Europa Nostra Prize for ‘conserving the European cultural heritage’ (Danish Nature Agency 2005). In this case, however, it seems that the conservation of one cultural heritage came at the expense of another cultural...... of Dissonance in Nature Restoration’, Journal of Landscape Architecture 2/2014: 58-67. Danish Nature Agency (2005), Skjern Å: Ådalens historie. De store projekter. Det nye landskab og naturen. På tur i ådalen [The Skjern River: The History of the River Delta. The Big Projects. The New Landscape and Nature...... heritage. While the meanders of the Skjern River were reconstructed according to its assumed course in 1870s, the embanked canal, which was the main feature and symbol of a comprehensive cultivation project from the 1960s, was deconstructed and reduced to incomprehensible traces of the past. Not only did...

  14. 49 CFR 234.221 - Lamp voltage.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Lamp voltage. 234.221 Section 234.221 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., Inspection, and Testing Maintenance Standards § 234.221 Lamp voltage. The voltage at each lamp shall...

  15. Bootstrapped Low-Voltage Analog Switches

    DEFF Research Database (Denmark)

    Steensgaard-Madsen, Jesper

    1999-01-01

    Novel low-voltage constant-impedance analog switch circuits are proposed. The switch element is a single MOSFET, and constant-impedance operation is obtained using simple circuits to adjust the gate and bulk voltages relative to the switched signal. Low-voltage (1-volt) operation is made feasible...

  16. Cascading failure analysis and restoration strategy in an interdependent network

    Science.gov (United States)

    Hong, Sheng; Lv, Chuan; Zhao, Tingdi; Wang, Baoqing; Wang, Jianghui; Zhu, Juxing

    2016-05-01

    In modern society, many infrastructures are interdependent owing to functional and logical relations among components in different systems. These networked infrastructures can be modeled as interdependent networks. In the real world, different networks carry different traffic loads whose values are dynamic and stem from the load redistribution in the same network and disturbance from the interdependent network. Interdependency makes interdependent networks so fragile that even a slight initial disturbance may lead to a cascading failure of the entire systems. In this paper, interdependencies among networks are modeled and a failure cascade process is studied considering their effects on failure propagation. Meanwhile, an in-process restoration strategy after the initial failure is investigated. The restoration effects depend strongly on the trigger timing, restoration probability and priority of the restoration actions along with the additional disturbances. Our findings highlight the necessity to decrease the large-scale cascading failure by structuring and managing an interdependent network reasonably.

  17. Voltage equilibration for reactive atomistic simulations of electrochemical processes

    Energy Technology Data Exchange (ETDEWEB)

    Onofrio, Nicolas; Strachan, Alejandro, E-mail: strachan@purdue.edu [School of Materials Engineering and Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47906 (United States)

    2015-08-07

    We introduce electrochemical dynamics with implicit degrees of freedom (EChemDID), a model to describe electrochemical driving force in reactive molecular dynamics simulations. The method describes the equilibration of external electrochemical potentials (voltage) within metallic structures and their effect on the self-consistent partial atomic charges used in reactive molecular dynamics. An additional variable assigned to each atom denotes the local potential in its vicinity and we use fictitious, but computationally convenient, dynamics to describe its equilibration within connected metallic structures on-the-fly during the molecular dynamics simulation. This local electrostatic potential is used to dynamically modify the atomic electronegativities used to compute partial atomic changes via charge equilibration. Validation tests show that the method provides an accurate description of the electric fields generated by the applied voltage and the driving force for electrochemical reactions. We demonstrate EChemDID via simulations of the operation of electrochemical metallization cells. The simulations predict the switching of the device between a high-resistance to a low-resistance state as a conductive metallic bridge is formed and resistive currents that can be compared with experimental measurements. In addition to applications in nanoelectronics, EChemDID could be useful to model electrochemical energy conversion devices.

  18. 基于SAN的快速灾难恢复技术%SAN-based Balefulness Restore Technology

    Institute of Scientific and Technical Information of China (English)

    蔡皖东; 陈亚滨; 戴冠中

    2002-01-01

    Fast balefulness restore technology is an importance part of network security architecture.It can reduces system loss and fast restores system functions while the system is attacked or occurs fault.In this paper,a SAN (Storage Area Network)-based Balefulness Restore system and resource management technology for the system are discussed.The system provides high balefulness tolerance performance and effcetively ensures network information system security by system fault tolerance and dynamic backup/restore technology.

  19. Measurement and analysis of postsynaptic potentials using a novel voltage-deconvolution method.

    Science.gov (United States)

    Richardson, Magnus J E; Silberberg, Gilad

    2008-02-01

    Accurate measurement of postsynaptic potential amplitudes is a central requirement for the quantification of synaptic strength, dynamics of short-term and long-term plasticity, and vesicle-release statistics. However, the intracellular voltage is a filtered version of the underlying synaptic signal and so a method of accounting for the distortion caused by overlapping postsynaptic potentials must be used. Here a voltage-deconvolution technique is demonstrated that defilters the entire voltage trace to reveal an underlying signal of well-separated synaptic events. These isolated events can be cropped out and reconvolved to yield a set of isolated postsynaptic potentials from which voltage amplitudes may be measured directly-greatly simplifying this common task. The method also has the significant advantage of providing a higher temporal resolution of the dynamics of the underlying synaptic signal. The versatility of the method is demonstrated by a variety of experimental examples, including excitatory and inhibitory connections to neurons with passive membranes and those with activated voltage-gated currents. The deconvolved current-clamp voltage has many features in common with voltage-clamp current measurements. These similarities are analyzed using cable theory and a multicompartment cell reconstruction, as well as direct comparison to voltage-clamp experiments.

  20. Experimental observation of direct current voltage-induced phase synchronization

    Indian Academy of Sciences (India)

    Haihong Li; Weiqing Liu; Qiongling Dai; Jinghua Xiao

    2006-09-01

    The dynamics of two uncoupled distinct Chua circuits driven by a common direct current voltage is explored experimentally. It was found that, with increasing current intensity, the dominant frequencies of these two Chua circuits will first vary at different speeds, approach an identical value for a certain current intensity and then separate. Techniques such as synchronization index and phase difference distribution were employed to analyze the phase coherence between these two Chua circuits.

  1. Archived film analysis and restoration

    NARCIS (Netherlands)

    Rares, A.

    2004-01-01

    The progressive degradation of current film archives poses a serious threat to the preservation of our cultural and technical heritage. Digitization and digital restoration are currently the most viable solutions for the long term preservation and high quality restoration of filmed material. They

  2. SOCIAL WELFARE AND RESTORATIVE JUSTICE

    Directory of Open Access Journals (Sweden)

    Darrell Fox

    2009-09-01

    Full Text Available This paper explores the links and connections between social work and restorative justice. After a brief description of social work, restorative justice and family group conferencing, I will explore some the complementary theoretical links and practice applications, critically examining the potential implications and opportunities for social work practitioners and academics in relation to practice.

  3. Archived film analysis and restoration

    NARCIS (Netherlands)

    Rares, A.

    2004-01-01

    The progressive degradation of current film archives poses a serious threat to the preservation of our cultural and technical heritage. Digitization and digital restoration are currently the most viable solutions for the long term preservation and high quality restoration of filmed material. They al

  4. PMU-Aided Voltage Security Assessment for a Wind Power Plant: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, H.; Zhang, Y. C.; Zhang, J. J.; Muljadi, E.

    2015-04-08

    Because wind power penetration levels in electric power systems are continuously increasing, voltage stability is a critical issue for maintaining power system security and operation. The traditional methods to analyze voltage stability can be classified into two categories: dynamic and steady-state. Dynamic analysis relies on time-domain simulations of faults at different locations; however, this method needs to exhaust faults at all locations to find the security region for voltage at a single bus. With the widely located phasor measurement units (PMUs), the Thevenin equivalent matrix can be calculated by the voltage and current information collected by the PMUs. This paper proposes a method based on a Thevenin equivalent matrix to identify system locations that will have the greatest impact on the voltage at the wind power plant’s point of interconnection. The number of dynamic voltage stability analysis runs is greatly reduced by using the proposed method. The numerical results demonstrate the feasibility, effectiveness, and robustness of the proposed approach for voltage security assessment for a wind power plant.

  5. PMU-Aided Voltage Security Assessment for a Wind Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Huaiguang; Zhang, Yingchen; Zhang, Jun Jason; Muljadi, Eduard

    2015-10-05

    Because wind power penetration levels in electric power systems are continuously increasing, voltage stability is a critical issue for maintaining power system security and operation. The traditional methods to analyze voltage stability can be classified into two categories: dynamic and steady-state. Dynamic analysis relies on time-domain simulations of faults at different locations; however, this method needs to exhaust faults at all locations to find the security region for voltage at a single bus. With the widely located phasor measurement units (PMUs), the Thevenin equivalent matrix can be calculated by the voltage and current information collected by the PMUs. This paper proposes a method based on a Thevenin equivalent matrix to identify system locations that will have the greatest impact on the voltage at the wind power plant's point of interconnection. The number of dynamic voltage stability analysis runs is greatly reduced by using the proposed method. The numerical results demonstrate the feasibility, effectiveness, and robustness of the proposed approach for voltage security assessment for a wind power plant.

  6. Voltage Management in Unbalanced Low Voltage Networks Using a Decoupled Phase-Tap-Changer Transformer

    DEFF Research Database (Denmark)

    Coppo, Massimiliano; Turri, Roberto; Marinelli, Mattia

    2014-01-01

    The paper studies a medium voltage-low voltage transformer with a decoupled on load tap changer capability on each phase. The overall objective is the evaluation of the potential benefits on a low voltage network of such possibility. A realistic Danish low voltage network is used for the analysis...

  7. Estimating Voltage Asymmetry Making by One Phase Micro-generator in Low Voltage Network

    Directory of Open Access Journals (Sweden)

    Marian Sobierajski

    2014-12-01

    Full Text Available Connection of one phase micro-generator to the low voltage network increases voltage asymmetry. The voltage asymmetry is defined as the quotient of negative and positive voltage components. The mathematical background of exact and rough computation of the asymmetry quotient is presented in the paper. Considerations are illustrated by simple examples.

  8. 76 FR 70721 - Voltage Coordination on High Voltage Grids; Notice of Staff Workshop

    Science.gov (United States)

    2011-11-15

    ... Energy Regulatory Commission Voltage Coordination on High Voltage Grids; Notice of Staff Workshop Take notice that the Federal Energy Regulatory Commission will hold a Workshop on Voltage Coordination on High Voltage Grids on Thursday, December 1, 2011 from 9 a.m. to 4:30 p.m. This staff-led workshop will be...

  9. A Comparative Study of Ultra-Low Voltage Digital Circuit Design

    Directory of Open Access Journals (Sweden)

    Aaron Arthurs

    2012-07-01

    Full Text Available Ultra-low voltage digital circuit design is an active research area, especially for portable applications such as wearable electronics, intelligent remote sensors, implantable medical devices, and energy-harvesting systems. Due to their application scenarios and circuit components, two major goals for these systems are minimizing energy consumption and improving compatibility with low-voltage power supplies and analog components. The most effective solution to achieve these goals is to reduce the supply voltage, which,however, raises the issue of operability. At ultra-low supply voltages, the integrity of digital signals degrades dramatically due to the indifference between active and leakage currents. In addition, the system timing becomes more unpredictable as the impact of process and supply voltage variations being more significant at lower voltages. This paper presents a comparative study among three techniques for designing digital circuits operating at ultra-low voltages, i.e., Schmitt-triggered gate structure, delayinsensitive asynchronous logic, and Fully-Depleted Silicon-on-Insulator technology. Results show that despite the tradeoffs, all eight combinations of these techniques are viable for designing ultra-low voltage circuits. For a given application, the optimum circuit design can be selected from these combinations based on the lowest voltage, the dynamic range, the power budget, the performance requirement, and the available semiconductor process node.

  10. A Comparative Study of Ultra-Low Voltage Digital Circuit Design

    Directory of Open Access Journals (Sweden)

    Aaron Arthurs,

    2012-06-01

    Full Text Available Ultra-low voltage digital circuit design is an active research area, especially for portable applications such as wearable electronics, intelligent remote sensors, implantable medical devices, and energy-harvesting systems. Due to their application scenarios and circuit components, two major goals for these systems are minimizing energy consumption and improving compatibility with low-voltage power supplies and analog components. The most effective solution to achieve these goals is to reduce the supply voltage, which,however, raises the issue of operability. At ultra-low supply voltages, the integrity of digital signals degrades dramatically due to the indifference between active and leakage currents. In addition, the system timing becomes more unpredictable as the impact of process and supply voltage variations being more significant at lower voltages. This paper presents a comparative study among three techniques for designing digital circuits operating at ultra-low voltages, i.e., Schmitt-triggered gate structure, delay insensitive asynchronous logic, and Fully-Depleted Silicon-on-Insulator technology. Results show that despite the trade offs, all eight combinations of these techniques are viable for designing ultra-low voltage circuits. For a given application, the optimum circuit design can be selected from these combinations based on the lowest voltage, the dynamic range, the power budget, the performance requirement, and the available semiconductor process node.

  11. Improving transition voltage spectroscopy of molecular junctions

    DEFF Research Database (Denmark)

    Markussen, Troels; Chen, Jingzhe; Thygesen, Kristian Sommer

    2011-01-01

    Transition voltage spectroscopy (TVS) is a promising spectroscopic tool for molecular junctions. The principles in TVS is to find the minimum on a Fowler-Nordheim plot where ln(I/V2) is plotted against 1/V and relate the voltage at the minimum Vmin to the closest molecular level. Importantly, Vmin...... is approximately half the voltage required to see a peak in the dI/dV curve. Information about the molecular level position can thus be obtained at relatively low voltages. In this work we show that the molecular level position can be determined at even lower voltages, Vmin(α), by finding the minimum of ln...

  12. Piezo Voltage Controlled Planar Hall Effect Devices

    Science.gov (United States)

    Zhang, Bao; Meng, Kang-Kang; Yang, Mei-Yin; Edmonds, K. W.; Zhang, Hao; Cai, Kai-Ming; Sheng, Yu; Zhang, Nan; Ji, Yang; Zhao, Jian-Hua; Zheng, Hou-Zhi; Wang, Kai-You

    2016-06-01

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the piezo voltage controlled Co2FeAl planar Hall effect devices without the external magnetic field. Our demonstration may lead to the realization of both information storage and processing using ferromagnetic materials.

  13. Piezo Voltage Controlled Planar Hall Effect Devices.

    Science.gov (United States)

    Zhang, Bao; Meng, Kang-Kang; Yang, Mei-Yin; Edmonds, K W; Zhang, Hao; Cai, Kai-Ming; Sheng, Yu; Zhang, Nan; Ji, Yang; Zhao, Jian-Hua; Zheng, Hou-Zhi; Wang, Kai-You

    2016-06-22

    The electrical control of the magnetization switching in ferromagnets is highly desired for future spintronic applications. Here we report on hybrid piezoelectric (PZT)/ferromagnetic (Co2FeAl) devices in which the planar Hall voltage in the ferromagnetic layer is tuned solely by piezo voltages. The change of planar Hall voltage is associated with magnetization switching through 90° in the plane under piezo voltages. Room temperature magnetic NOT and NOR gates are demonstrated based on the piezo voltage controlled Co2FeAl planar Hall effect devices without the external magnetic field. Our demonstration may lead to the realization of both information storage and processing using ferromagnetic materials.

  14. Identification of Acceptable Restoration Strategies

    Directory of Open Access Journals (Sweden)

    Seung-Tae Cha

    2008-04-01

    Full Text Available In recent years, we have seen several catastrophic and cascading failures of power systems throughout the world. Power system breakup and blackouts are rare events. However, when they occur, the effects on utilities and general population can be quite severe. To prevent or reduce cascading sequences of events caused by the various reasons, KEPRI is researching ways to revolutionize innovative strategies that will significantly reduce the vulnerability of the power system and will ensure successful restoration of service to customers. This paper describes a restoration guidelines / recommendations for the KEPS simulator, which allows power system operator and planner to simulate and plan restoration events in an interactive mode. The KEPS simulator provides a list of restoration events according to the priority based on some restoration rules and list of priority loads. Further, the paper will draw on research using information from a Jeju case study.

  15. Ant Colony Search Algorithm for Optimal Generators Startup during Power System Restoration

    OpenAIRE

    A. Ketabi; Feuillet, R

    2010-01-01

    Generators startup sequence plays a significant role in achieving a suitable and effective restoration strategy. This paper outlines an ant colony search algorithm in order to determine the generator starting times during the bulk power system restoration. The algorithm attempts to maximize the system generation capability over a restoration period, where the dynamic characteristics of different types of units and system constraints are considered. Applying this method for the 39-bus New Engl...

  16. Capacitor Voltages Measurement and Balancing in Flying Capacitor Multilevel Converters Utilizing a Single Voltage Sensor

    DEFF Research Database (Denmark)

    Farivar, Glen; Ghias, Amer M. Y. M.; Hredzak, Branislav

    2017-01-01

    This paper proposes a new method for measuring capacitor voltages in multilevel flying capacitor (FC) converters that requires only one voltage sensor per phase leg. Multiple dc voltage sensors traditionally used to measure the capacitor voltages are replaced with a single voltage sensor at the ac...... side of the phase leg. The proposed method is subsequently used to balance the capacitor voltages using only the measured ac voltage. The operation of the proposed measurement and balancing method is independent of the number of the converter levels. Experimental results presented for a five-level FC...

  17. Modeling and Design of DC Boost and AC Side Voltage Controllers in Asymmetrical Γ-Source Inverter

    Directory of Open Access Journals (Sweden)

    Seyed Mahyar Mehdizadeh Moghadam

    2014-07-01

    Full Text Available In this paper a control system is proposed to simultaneously control the voltage boost and output voltage of assymetrical Γ-Source Inverters. Dynamic model of the system is used to design the controllers. Voltage boost on assymetrical Γ-Source Inverters is done by voltage control of impedance network capacitor and the regulation of inverter shoot through duty cycle. Since the stability margin of the system is low due to the right half plane zero in its dynamic model, the design of fast control system is impossible therefore a nonlinear feedforward control loop is used to faster the control system performance. Linear control system is used to control the AC-side in synchrony reference frame such that the AC voltage control system regulates the output voltage by means of modulation index regulation. The proposed control system performance is investigated by simulation in MATLAB/Simulink

  18. Voltage-Sensitive Load Controllers for Voltage Regulation and Increased Load Factor in Distribution Systems

    DEFF Research Database (Denmark)

    Douglass, Philip James; Garcia-Valle, Rodrigo; Østergaard, Jacob

    2014-01-01

    consumption which can be mapped to temperature setpoint offsets of thermostat controlled loads. In networks where a lower voltage level corresponds to high system load (and vice versa), this controller acts to regulate voltage and increase the load factor. Simulations are conducted on low- and medium-voltage......This paper presents a novel controller design for controlling appliances based on local measurements of voltage. The controller finds the normalized voltage deviation accounting for the sensitivity of voltage measurements to appliance state. The controller produces a signal indicating desired power...... distribution systems with residential loads including voltage-sensitive water heaters. In low-voltage systems, the results of the simulations show the controller to be effective at reducing the extremes of voltage and increasing the load factor while respecting end-use temperature constraints. In medium-voltage...

  19. Voltage-controlled photonic oscillator.

    Science.gov (United States)

    Savchenkov, A A; Ilchenko, V S; Liang, W; Eliyahu, D; Matsko, A B; Seidel, D; Maleki, L

    2010-05-15

    We report the development and demonstration of an X-band voltage-controlled photonic oscillator based on a whispering gallery mode resonator made of an electro-optic crystalline material. The oscillator has good spectral purity and wide, agile, linear tunability. We have modified the existing theoretical model of the opto-electronic oscillator to describe the performance of our tunable oscillator and have found a good agreement between the theoretical predictions and the measurement results. We show that the device is promising for higher-frequency applications where high-performance tunable oscillators with wide tunability do not exist.

  20. Restoration treatments in urban park forests drive long-term changes in vegetation trajectories.

    Science.gov (United States)

    Johnson, Lea R; Handel, Steven N

    2016-04-01

    Municipalities are turning to ecological restoration of urban forests as a measure to improve air quality, ameliorate urban heat island effects, improve storm water infiltration, and provide other social and ecological benefits. However, community dynamics following urban forest restoration treatments are poorly documented. This study examines the long-term effects of ecological restoration undertaken in New York City, New York, USA, to restore native forest in urban park natural areas invaded by woody non-native plants that are regional problems. In 2009 and 2010, we sampled vegetation in 30 invaded sites in three large public parks that were restored 1988-1993, and 30 sites in three large parks that were similarly invaded but had not been restored. Data from these matched plots reveal that the restoration treatment achieved its central goals. After 15-20 years, invasive species removal followed by native tree planting resulted in persistent structural and compositional shifts, significantly lower invasive species abundance, a more complex forest structure, and greater native tree recruitment. Together, these findings indicate that successional trajectories of vegetation dynamics have diverged between restored forests and invaded forests that were not restored. In addition, the data suggest that future composition of these urban forest patches will be novel assemblages. Restored and untreated sites shared a suite of shade-intolerant, quickly-growing tree species that colonize disturbed sites, indicating that restoration treatments created sites hospitable for germination and growth of species adapted to high light conditions and disturbed soils. These findings yield an urban perspective on the use of succession theory in ecological restoration. Models of ecological restoration developed in more pristine environments must be modified for use in cities. By anticipating both urban disturbances and ecological succession, management of urban forest patches can be

  1. A New Coordinated Voltage Control Scheme for Offshore AC Grid of HVDC Connected Offshore Wind Power Plants

    DEFF Research Database (Denmark)

    Sakamuri, Jayachandra N.; Cutululis, Nicolaos Antonio; Rather, Zakir Hussain;

    2015-01-01

    This paper proposes a coordinated voltage control scheme (CVCS) which enhances the voltage ride through (VRT) capability of an offshore AC grid comprised of a cluster of offshore wind power plants (WPP) connected through AC cables to the offshore voltage source converter based high voltage DC (VSC-HVDC......) converter station. Due to limited short circuit power contribution from power electronic interfaced variable speed wind generators and with the onshore main grid decoupled by the HVDC link, the offshore AC grid becomes more vulnerable to dynamic voltage events. Therefore, a short circuit fault...... in the offshore AC Grid is likely to have significant implications on the voltage of the offshore AC grid, hence on the power flow to the onshore mainland grid. The proposed CVCS integrates individual local reactive power control of wind turbines and of the HVDC converter with the secondary voltage controller...

  2. Restoration of optic neuropathy

    Directory of Open Access Journals (Sweden)

    You SW

    2017-03-01

    . Many genes, such as Bcl-2, PTEN, and mTOR, are crucial in cell proliferation, axon guidance, and growth during development, and play important roles in the regeneration and extension of RGC axons. With transgenic mice and related gene regulations, robust regeneration of RGC axons has been observed after ON injury in laboratories. Although various means of experimental treatments such as cell transplantation and gene therapy have achieved significant progress in neuronal survival, axonal regeneration, and restoration of the visual function after ON injury, many unresolved scientific problems still exist for their clinical applications. Therefore, we still need to overcome hurdles before developing effective therapy to treat optic neuropathy diseases in patients. Keywords: retinal ganglion cells, optic nerve injury, neuronal survival, axonal regeneration, vision restoration

  3. Voltage Management in Unbalanced Low Voltage Networks Using a Decoupled Phase-Tap-Changer Transformer

    OpenAIRE

    Coppo, Massimiliano; Turri, Roberto; Marinelli, Mattia; Han, Xue

    2014-01-01

    The paper studies a medium voltage-low voltage transformer with a decoupled on load tap changer capability on each phase. The overall objective is the evaluation of the potential benefits on a low voltage network of such possibility. A realistic Danish low voltage network is used for the analysis. The load profiles are characterized by using single phase measurement data on voltages, currents and active powers with a 10 minutes resolution. Different scenarios are considered: no tap action, th...

  4. Creating a catchment perspective for river restoration

    Science.gov (United States)

    Benda, L.; Miller, D.; Barquín, J.

    2011-03-01

    One of the major challenges in river restoration is to identify the natural fluvial landscape in catchments with a long history of river control. Intensive land use on valley floors often predates the earliest remote sensing: levees, dikes, dams, and other structures alter valley-floor morphology, river channels and flow regimes. Consequently, morphological patterns indicative of the fluvial landscape including multiple channels, extensive floodplains, wetlands, and fluvial-riparian and tributary-confluence dynamics can be obscured, and information to develop appropriate and cost effective river restoration strategies can be unavailable. This is the case in the Pas River catchment in northern Spain (650 km2), in which land use and development have obscured the natural fluvial landscape in many parts of the basin. To address this issue we coupled general principles of hydro-geomorphic processes with computer tools to characterize the fluvial landscape. Using a 5-m digital elevation model, valley-floor surfaces were mapped according to elevation above the channel and proximity to key geomorphic processes. The predicted fluvial landscape is patchily distributed according to topography, valley morphology, river network structure, and fan and terrace landforms. The vast majority of the fluvial landscape in the main segments of the Pas River catchment is presently masked by human infrastructure, with only 15% not impacted by river control structures and development. The reconstructed fluvial landscape provides a catchment scale context to support restoration planning, in which areas of potential ecological productivity and diversity could be targeted for in-channel, floodplain and riparian restoration projects.

  5. Creating a catchment perspective for river restoration

    Directory of Open Access Journals (Sweden)

    L. Benda

    2011-03-01

    Full Text Available One of the major challenges in river restoration is to identify the natural fluvial landscape in catchments with a long history of river control. Intensive land use on valley floors often predates the earliest remote sensing: levees, dikes, dams, and other structures alter valley-floor morphology, river channels and flow regimes. Consequently, morphological patterns indicative of the fluvial landscape including multiple channels, extensive floodplains, wetlands, and fluvial-riparian and tributary-confluence dynamics can be obscured, and information to develop appropriate and cost effective river restoration strategies can be unavailable. This is the case in the Pas River catchment in northern Spain (650 km2, in which land use and development have obscured the natural fluvial landscape in many parts of the basin. To address this issue we coupled general principles of hydro-geomorphic processes with computer tools to characterize the fluvial landscape. Using a 5-m digital elevation model, valley-floor surfaces were mapped according to elevation above the channel and proximity to key geomorphic processes. The predicted fluvial landscape is patchily distributed according to topography, valley morphology, river network structure, and fan and terrace landforms. The vast majority of the fluvial landscape in the main segments of the Pas River catchment is presently masked by human infrastructure, with only 15% not impacted by river control structures and development. The reconstructed fluvial landscape provides a catchment scale context to support restoration planning, in which areas of potential ecological productivity and diversity could be targeted for in-channel, floodplain and riparian restoration projects.

  6. The Hip Restoration Algorithm

    Science.gov (United States)

    Stubbs, Allston Julius; Atilla, Halis Atil

    2016-01-01

    Summary Background Despite the rapid advancement of imaging and arthroscopic techniques about the hip joint, missed diagnoses are still common. As a deep joint and compared to the shoulder and knee joints, localization of hip symptoms is difficult. Hip pathology is not easily isolated and is often related to intra and extra-articular abnormalities. In light of these diagnostic challenges, we recommend an algorithmic approach to effectively diagnoses and treat hip pain. Methods In this review, hip pain is evaluated from diagnosis to treatment in a clear decision model. First we discuss emergency hip situations followed by the differentiation of intra and extra-articular causes of the hip pain. We differentiate the intra-articular hip as arthritic and non-arthritic and extra-articular pain as surrounding or remote tissue generated. Further, extra-articular hip pain is evaluated according to pain location. Finally we summarize the surgical treatment approach with an algorithmic diagram. Conclusion Diagnosis of hip pathology is difficult because the etiologies of pain may be various. An algorithmic approach to hip restoration from diagnosis to rehabilitation is crucial to successfully identify and manage hip pathologies. Level of evidence: V. PMID:28066734

  7. 计及动态无功控制影响的风电汇集地区高电压脱网原因分析%Analysis on High-voltage Trip-off Causation of Dense Wind Power Areas Considering Impact of Dynamic Reactive Power Control

    Institute of Scientific and Technical Information of China (English)

    谢欢; 吴涛; 赵亚清; 蓝海波; 刘海涛; 刘辉

    2015-01-01

    回顾电网实际发生的某次风电机组高电压脱网事故典型特征,总结提出:研究导致事故深层原因应充分考虑风电场汇集地区动态无功补偿控制的影响。基于简单系统推导出计及风电场感性支路恒无功控制影响的无功功率—电压灵敏度表达式,从原理上阐明目前动态无功补偿装置所广泛采用的感性支路恒无功控制方式将导致大规模风电汇集地区电网无功功率—电压灵敏度增大,其增大的幅度取决于感性支路的初值,并最终指出风电场感性支路恒无功控制方式导致的无功功率—电压灵敏度增大是导致“5·14”风电大规模脱网的主要原因之一。最后,结合实际系统的典型案例进行了仿真验证。%The typical characteristics of a certain high-voltage trip-off accident of wind turbines that does happen in a power system are reviewed.It is concluded that in learning about the root cause of the accident,we need to give careful consideration of the impact of dynamic reactive compensation control.Based on a simple equivalent system,the reactive power-voltage sensitivity expression considering the influence of constant reactive power control of inductive branch in dense wind power areas is derived.It is proved in principle that constant reactive power control on the inductive branch adopted by a static reactive compensator will cause an increase in reactive power-voltage sensitivity.And the growth rate depends on the initial value of the inductive branch.Further,it is pointed out that the increase in reactive power-voltage sensitivity due to constant reactive power control on the inductive branch is one of the main causes that leads to the“5 ·14" high-voltage trip-off accident.Finally,the typical case of an actual system is verified by simulation.

  8. Research on the low-voltage ride-through capability of wind synchronous generator with hydro-dynamically controlled gearbox%液力变矩型同步风力发电机低电压穿越性能分析

    Institute of Scientific and Technical Information of China (English)

    王军伟

    2016-01-01

    液力变矩型同步风力发电机组是国内近期投运的一种新机型,它的核心技术是应用WinDrive液力变矩器进行变矩调速,实现风机可变输入转速的恒速输出,为发电机同步并网提供稳定的输入转速。同步发电机的励磁系统配套自动电压调节器进行励磁控制,有效地解决了传统风机低电压穿越能力差、无功输出能力不足的问题。针对2.0MW液力变矩型同步风力发电机的运行特点,研究其工作原理及控制策略,建立机组主要组件的数学模型,结合实际参数进行模拟仿真,分析了电网短路故障时机组低电压穿越的动态响应能力。%The wind synchronous generator with hydro-dynamically controlled gearbox is a new type of machine applied to wind turbine in China in recent years, and the heart of its technology is to apply WinDrive variable-speed hydraulic torque converter for the purpose of speed adjustment. It can convert the variable input speed into the constant speed output, and can provide a stable input speed for generator synchronous grid connection. Especially, the synchronous generator works together with AVR and has well excitation control function, and it effectively solves the problems that the low voltage ride through capability of the traditional turbine is poor and the reactive power output capability is insufficient. Based on the operation characteristics of 2.0MW wind synchronous generator with hydro-dynamically controlled gearbox by studying its working principles and control strategies, the mathematical model of the main components of the unit is established, the simulation experiments combined with the actual parameters are presented, and the low-voltage ride-through dynamic-response capability of the system at the very moment of grid short-circuit fault is also studied.

  9. Multiple CMS-restorer gene polymorphism in gynodioecious Plantago coronopus

    NARCIS (Netherlands)

    Damme, van J.M.M.; Hundscheid, M.P.J.; Ivanovic, S.; Koelewijn, H.P.

    2004-01-01

    The mode of inheritance of the male sterility trait is crucial for understanding the evolutionary dynamics of the sexual system gynodioecy, which is the co-occurrence of female and hermaphrodite plants in natural populations. Both cytoplasmic (CMS) and nuclear (restorer) genes are known to be involv

  10. Smart Demand for Improving Short-term Voltage Control on Distribution Networks

    DEFF Research Database (Denmark)

    Garcia-Valle, Rodrigo; P. Da Silva, Luiz C.; Xu, Zhao

    2009-01-01

    customer integration to aid power system performance is almost inevitable. This study introduces a new type of smart demand side technology, denoted demand as voltage controlled reserve (DVR), to improve short-term voltage control, where customers are expected to play a more dynamic role to improve voltage...... control. The technology can be provided by thermostatically controlled loads as well as other types of load. This technology is proven to be effective in case of distribution systems with a large composition of induction motors, where the voltage presents a slow recovery characteristic due to deceleration...... of the motors during faults. This study presents detailed models, discussion and simulation tests to demonstrate the technical viability and effectiveness of the DVR technology for short-term voltage control....

  11. Suppression of Spiral Waves by Voltage Clamp Techniques in a Conductance-Based Cardiac Tissue Model

    Institute of Scientific and Technical Information of China (English)

    YU Lian-Chun; MA Jun; ZHANG Guo-Yong; CHEN Yong

    2008-01-01

    A new control method is proposed to control the spatio-temporal dynamics in excitable media, which is described by the Morris-Lecar cells model. It is confirmed that successful suppression of spiral waves can be obtained by spatially clamping the membrane voltage of the excitable cells. The low voltage clamping induces breakup of spiral waves and the fragments are soon absorbed by low voltage obstacles, whereas the high voltage clamping generates travel waves that annihilate spiral waves through collision with them. However, each method has its shortcomings. Furthermore, a two-step method that combines both low and high voltage clamp techniques is then presented as a possible way of out this predicament.

  12. Switchable voltage control of the magnetic coercive field via magnetoelectric effect

    Science.gov (United States)

    Wang, Jing; Ma, Jing; Li, Zheng; Shen, Yang; Lin, Yuanhua; Nan, C. W.

    2011-08-01

    Switchable voltage modulation of the magnetic properties is reported in different multiferroic bilayers with magnetic films grown on pre-poled ferroelectric substrates, based on the magneto-optical Kerr effect observations. The dynamic voltage control of the magnetic coercive field (Hc) is dependent not only on the materials properties of each ferroic layer, but also on the bias voltage history. The Hc versus electric field behaviors essentially track the dependence of the piezostrains of the substrates on the bias voltage. The observations demonstrate that Hc in such multiferroic bilayers can be controlled by voltage via strain-mediated magnetoelectric coupling and that the Hc change is not an artifact due to a heating effect.

  13. 49 CFR 236.551 - Power supply voltage; requirement.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Power supply voltage; requirement. 236.551 Section... supply voltage; requirement. The voltage of power supply shall be maintained within 10 percent of rated voltage....

  14. Steering liquid metal flow in microchannels using low voltages.

    Science.gov (United States)

    Tang, Shi-Yang; Lin, Yiliang; Joshipura, Ishan D; Khoshmanesh, Khashayar; Dickey, Michael D

    2015-10-07

    Liquid metals based on gallium, such as eutectic gallium indium (EGaIn) and Galinstan, have been integrated as static components in microfluidic systems for a wide range of applications including soft electrodes, pumps, and stretchable electronics. However, there is also a possibility to continuously pump liquid metal into microchannels to create shape reconfigurable metallic structures. Enabling this concept necessitates a simple method to control dynamically the path the metal takes through branched microchannels with multiple outlets. This paper demonstrates a novel method for controlling the directional flow of EGaIn liquid metal in complex microfluidic networks by simply applying a low voltage to the metal. According to the polarity of the voltage applied between the inlet and an outlet, two distinct mechanisms can occur. The voltage can lower the interfacial tension of the metal via electrocapillarity to facilitate the flow of the metal towards outlets containing counter electrodes. Alternatively, the voltage can drive surface oxidation of the metal to form a mechanical impediment that redirects the movement of the metal towards alternative pathways. Thus, the method can be employed like a 'valve' to direct the pathway chosen by the metal without mechanical moving parts. The paper elucidates the operating mechanisms of this valving system and demonstrates proof-of-concept control over the flow of liquid metal towards single or multiple directions simultaneously. This method provides a simple route to direct the flow of liquid metal for applications in microfluidics, optics, electronics, and microelectromechanical systems.

  15. Fernald restoration: ecologists and engineers integrate restoration and cleanup

    Energy Technology Data Exchange (ETDEWEB)

    Woods, Eric; Homer, John

    2002-07-15

    As cleanup workers excavate pits and tear down buildings at the Fernald site in southwest Ohio, site ecologists are working side-by-side to create thriving wetlands and develop the early stages of forest, prairie, and savanna ecosystems to restore natural resources that were impacted by years of site operations. In 1998, the U.S. Department of Energy-Fernald Office (DOE-FN) and its cleanup contractor, Fluor Fernald, Inc., initiated several ecological restoration projects in perimeter areas of the site (e.g., areas not used for or impacted by uranium processing or waste management). The projects are part of Fernald's final land use plan to restore natural resources over 904 acres of the 1,050-acre site. Pete Yerace, the DOE-FN Natural Resource Trustee representative is working with the Fernald Natural Resource Trustees in an oversight role to resolve the state of Ohio's 1986 claim against DOE for injuries to natural resources. Fluor Fernald, Inc., and DOE-FN developed the ''Natural Resource Restoration Plan'', which outlines 15 major restoration projects for the site and will restore injured natural resources at the site. In general, Fernald's plan includes grading to maximize the formation of wetlands or expanded floodplain, amending soil where topsoil has been removed during excavation, and establishing native vegetation throughout the site. Today, with cleanup over 35 percent complete and site closure targeted for 2006, Fernald is entering a new phase of restoration that involves heavily remediated areas. By working closely with engineers and cleanup crews, site ecologists can take advantage of remediation fieldwork (e.g., convert an excavated depression into a wetland) and avoid unnecessary costs and duplication. This collaboration has also created opportunities for relatively simple and inexpensive restoration of areas that were discovered during ongoing remediation. To ensure the survival of the plant material in heavily

  16. Voltage Unbalance Compensation with Smart Three-phase Loads

    DEFF Research Database (Denmark)

    Douglass, Philip; Trintis, Ionut; Munk-Nielsen, Stig

    2016-01-01

    voltage, but it does not reduce the negative sequence voltage. The controller that uses phase-phase voltage as input eliminates negative sequence voltage, and reduces voltage deviations from the average to approximately half their initial value. Current unbalance is reduced when the voltage unbalance...... is caused by asymmetrical loads. These results suggest that the optimal algorithm to reduce system unbalance depends on which system parameter is most important: phase-neutral voltage unbalance, phase-phase voltage unbalance, or current unbalance....

  17. VT River Restoration Data in Lamoille County

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) Documented river and riparian buffer restoration projects in Lamoille County, Vermont. Restoration includes buffer plantings (trees and shrubs),...

  18. Performance evaluation of Type-3 PLLs under wide variation in input voltage and frequency

    DEFF Research Database (Denmark)

    Aravind, C. K.; Rani, B.Indu; Chakkarapani, M.

    2017-01-01

    This paper presents a detailed analysis of Type-3 PLL under wide variation in input voltage and frequency. Using small signal modeling, the performance of both single loop and dual loop type-3 PLL for variation in input voltage and frequency is studied. The analysis shows that for the same...... bandwidth, both the single loop and dual loop Type-3 PLL exhibit similar dynamics provided the supply voltage is balanced. However, under voltage sag conditions, dual loop PLL shows improved dynamic response without affecting its stability. Further, the tracking time is reduced as the feed forward frequency...... is a function of supply frequency. To improve the filtering characteristics under frequency deviations, a dual loop Type 3 adaptive PLL which accurately tracks the phase and frequency of the input signal under wide frequency deviations is developed. Simulations are carried out in MATLAB and experimentally...

  19. Voltage-Driven Magnetization Switching and Spin Pumping in Weyl Semimetals

    Science.gov (United States)

    Kurebayashi, Daichi; Nomura, Kentaro

    2016-10-01

    We demonstrate electrical magnetization switching and spin pumping in magnetically doped Weyl semimetals. The Weyl semimetal is a three-dimensional gapless topological material, known to have nontrivial coupling between the charge and the magnetization due to the chiral anomaly. By solving the Landau-Lifshitz-Gilbert equation for a multilayer structure of a Weyl semimetal, an insulator and a metal while taking the charge-magnetization coupling into account, magnetization dynamics is analyzed. It is shown that the magnetization dynamics can be driven by the electric voltage. Consequently, switching of the magnetization with a pulsed electric voltage can be achieved, as well as precession motion with an applied oscillating electric voltage. The effect requires only a short voltage pulse and may therefore be energetically favorable for us in spintronics devices compared to conventional spin-transfer torque switching.

  20. Restoration handbook for sagebrush steppe ecosystems with emphasis on greater sage-grouse habitat—Part 1. Concepts for understanding and applying restoration

    Science.gov (United States)

    Pyke, David A.; Chambers, Jeanne C.; Pellant, Mike; Knick, Steven T.; Miller, Richard F.; Beck, Jeffrey L.; Doescher, Paul S.; Schupp, Eugene W.; Roundy, Bruce A.; Brunson, Mark; McIver, James D.

    2015-10-26

    Sagebrush steppe ecosystems in the United States currently occur on only about one-half of their historical land area because of changes in land use, urban growth, and degradation of land, including invasions of non-native plants. The existence of many animal species depends on the existence of sagebrush steppe habitat. The greater sage-grouse (Centrocercus urophasianus) is a landscape-dependent bird that requires intact habitat and combinations of sagebrush and perennial grasses to exist. In addition, other sagebrush-obligate animals also have similar requirements and restoration of landscapes for greater sage-grouse also will benefit these animals. Once sagebrush lands are degraded, they may require restoration actions to make those lands viable habitat for supporting sagebrushobligate animals. This restoration handbook is the first in a three-part series on restoration of sagebrush ecosystems. In Part 1, we discuss concepts surrounding landscape and restoration ecology of sagebrush ecosystems and greater sage-grouse that habitat managers and restoration practitioners need to know to make informed decisions regarding where and how to restore specific areas. We will describe the plant dynamics of sagebrush steppe ecosystems and their responses to major disturbances, fire, and defoliation. We will introduce the concepts of ecosystem resilience to disturbances and resistance to invasions of annual grasses within sagebrush steppe. An introduction to soils and ecological site information will provide insights into the specific plants that can be restored in a location. Soil temperature and moisture regimes are described as a tool for determining resilience and resistance and the potential for various restoration actions. Greater sage-grouse are considered landscape birds that require large areas of intact sagebrush steppe; therefore, we describe concepts of landscape ecology that aid our decisions regarding habitat restoration. We provide a brief overview of