Secondary recrystallization behavior in a twin-roll cast grain-oriented electrical steel

Energy Technology Data Exchange (ETDEWEB)

Song, Hong-Yu; Liu, Hai-Tao, E-mail: liuht@ral.neu.edu.cn; Wang, Yin-Ping; Wang, Guo-Dong

2017-04-15

The microstructure and texture evolution along the processing was investigated with a particular focus on the secondary recrystallization behavior in a 0.23 mm-thick twin-roll cast grain-oriented electrical steel. A striking feature is that Goss orientation originated during twin-roll casting as a result of shear deformation and it was further enhanced during hot rolling and normalizing. After primary recrystallization annealing, a homogeneous microstructure associated with a sharp γ-fiber texture was produced. During secondary recrystallization annealing, the γ-fiber texture was first strengthened and weakened with increasing temperature prior to the onset of secondary recrystallization. Goss grains always exhibited more 20–45° misoriented boundaries than the matrix. The matrix was quite stable during secondary recrystallization with the aid of dense inhibitors. Finally, a complete secondary recrystallization microstructure consisting of large Goss grains was produced. The grain boundary characteristics distribution indicated that the high energy model was responsible for the abnormal growth of Goss grains under the present conditions. - Highlights: • A 0.23 mm twin-roll cast grain-oriented silicon steel sheet was produced. • Goss orientation originated during twin-roll casting. • Secondary recrystallization behavior was briefly investigated. • γ-fiber texture was enhanced prior to the onset of secondary recrystallization. • A complete secondary recrystallization microstructure was produced.

A novel unified dislocation density-based model for hot deformation behavior of a nickel-based superalloy under dynamic recrystallization conditions

International Nuclear Information System (INIS)

Lin, Y.C.; Wen, Dong-Xu; Chen, Xiao-Min; Chen, Ming-Song

2016-01-01

In this study, a novel unified dislocation density-based model is presented for characterizing hot deformation behaviors in a nickel-based superalloy under dynamic recrystallization (DRX) conditions. In the Kocks-Mecking model, a new softening item is proposed to represent the impacts of DRX behavior on dislocation density evolution. The grain size evolution and DRX kinetics are incorporated into the developed model. Material parameters of the developed model are calibrated by a derivative-free method of MATLAB software. Comparisons between experimental and predicted results confirm that the developed unified dislocation density-based model can nicely reproduce hot deformation behavior, DRX kinetics, and grain size evolution in wide scope of initial grain size, strain rate, and deformation temperature. Moreover, the developed unified dislocation density-based model is well employed to analyze the time-variant forming processes of the studied superalloy. (orig.)

A novel unified dislocation density-based model for hot deformation behavior of a nickel-based superalloy under dynamic recrystallization conditions

Energy Technology Data Exchange (ETDEWEB)

Lin, Y.C. [Central South University, School of Mechanical and Electrical Engineering, Changsha (China); Light Alloy Research Institute of Central South University, Changsha (China); State Key Laboratory of High Performance Complex Manufacturing, Changsha (China); Wen, Dong-Xu; Chen, Xiao-Min [Central South University, School of Mechanical and Electrical Engineering, Changsha (China); Chen, Ming-Song [Central South University, School of Mechanical and Electrical Engineering, Changsha (China); State Key Laboratory of High Performance Complex Manufacturing, Changsha (China)

2016-09-15

In this study, a novel unified dislocation density-based model is presented for characterizing hot deformation behaviors in a nickel-based superalloy under dynamic recrystallization (DRX) conditions. In the Kocks-Mecking model, a new softening item is proposed to represent the impacts of DRX behavior on dislocation density evolution. The grain size evolution and DRX kinetics are incorporated into the developed model. Material parameters of the developed model are calibrated by a derivative-free method of MATLAB software. Comparisons between experimental and predicted results confirm that the developed unified dislocation density-based model can nicely reproduce hot deformation behavior, DRX kinetics, and grain size evolution in wide scope of initial grain size, strain rate, and deformation temperature. Moreover, the developed unified dislocation density-based model is well employed to analyze the time-variant forming processes of the studied superalloy. (orig.)

Metadynamic and static recrystallization softening behavior of a bainite steel

Science.gov (United States)

Li, Lixin; Zheng, Liangyu; Ye, Ben; Tong, Zeqiong

2018-01-01

The metadynamic recrystallization (MDRX) and static recrystallization (SRX) softening behavior of a bainite steel was investigated by two-pass isothermal compression experiments at temperatures of 1173, 1273, 1373, and 1473 K and strain rates of 0.01, 0.1, 1, and 10 s-1 with inter-pass times of 1, 5, 10, and 30 s on a Gleeble-1500 thermo-mechanical simulator. Kinetic equations were developed to evaluate the softening fractions caused by MDRX and SRX. A comparison between the experimental and predicted softening fractions showed that the proposed kinetic equations can provide a precise estimation of the MDRX and SRX behavior of the studied steel. The results based on the kinetic equations indicated that the MDRX and SRX softening fraction increases with the increase in strain rate, deformation temperature, inter-pass time, and pre-strain; the activation energy of MDRX is much smaller than that of SRX; and the no-recrystallization temperature of the investigated steel is 1179.4 K.

Effect of strain-induced precipitation on dynamic recrystallization in Mg–Al–Sn alloys

International Nuclear Information System (INIS)

Kabir, Abu Syed Humaun; Sanjari, Mehdi; Su, Jing; Jung, In-Ho; Yue, Stephen

2014-01-01

Two different amounts of tin (Sn) were added to a Mg–3 wt% Al binary alloy to form different amounts of precipitates during hot deformation. The thermodynamic modeling software, FactSage ™ , was used to calculate the amounts of Sn to generate the desired relative levels of precipitation. The alloys were deformed at four different temperatures and three different strain rates to generate different amounts of precipitates. The objective was to study the effect of these precipitates on dynamic recrystallization. The results indicated that the formation of strain-induced precipitates is a function of deformation temperature, strain, and strain rate. The findings also revealed that higher amounts of precipitates reduced the volume fraction of dynamic recrystallization and refined the dynamically recrystallized grain size

Analysis of recrystallization behavior of hot-deformed austenite reconstructed from electron backscattering diffraction orientation maps of lath martensite

International Nuclear Information System (INIS)

Kubota, Manabu; Ushioda, Kohsaku; Miyamoto, Goro; Furuhara, Tadashi

2016-01-01

The recrystallization behavior of hot-deformed austenite of a 0.55% C steel at 800 °C was investigated by a method of reconstructing the parent austenite orientation map from an electron backscattering diffraction orientation map of lath martensite. Recrystallized austenite grains were clearly distinguished from un-recrystallized austenite grains. Very good correlation was confirmed between the static recrystallization behavior investigated mechanically by double-hit compression tests and the change in austenite microstructure evaluated by the reconstruction method. The recrystallization behavior of hot-deformed 0.55% C steel at 800 °C is directly revealed and it was observed that by addition of 0.1% V the recrystallization was significantly retarded.

Dynamic moisture sorption characteristics of enzyme-resistant recrystallized cassava starch.

Science.gov (United States)

Mutungi, Christopher; Schuldt, Stefan; Onyango, Calvin; Schneider, Yvonne; Jaros, Doris; Rohm, Harald

2011-03-14

The interaction of moisture with enzyme-resistant recrystallized starch, prepared by heat-moisture treatment of debranched acid-modified or debranched non-acid-modified cassava starch, was investigated in comparison with the native granules. Crystallinities of the powdered products were estimated by X-ray diffraction. Moisture sorption was determined using dynamic vapor sorption analyzer and data fitted to various models. Percent crystallinities of native starch (NS), non-acid-modified recrystallized starch (NAMRS), and acid-modified recrystallized starch (AMRS) were 39.7, 51.9, and 56.1%, respectively. In a(w) below 0.8, sorption decreased in the order NS > NAMRS > AMRS in line with increasing sample crystallinities but did not follow this crystallinity dependence at higher a(w) because of condensation and polymer dissolution effects. Adsorbed moisture became internally absorbed in NS but not in NAMRS and AMRS, which might explain the high resistance of the recrystallized starches to digestion because enzyme and starch cannot approach each other over fairly sufficient surface at the molecular level.

A two-site mean field model of discontinuous dynamic recrystallization

International Nuclear Information System (INIS)

Bernard, P.; Bag, S.; Huang, K.; Loge, R.E.

2011-01-01

Highlights: → Discontinuous dynamic recrystallization (DDRX) is modelled at the grain scale. → The two-site mean field approach allows introducing topological information. → DDRX kinetics, flow stress curves and recrystallized grain size are well predicted. → Temperature, strain rate and initial grain size effects are successfully described. → Grain size dependence naturally emerges from the model and agrees with experiment. - Abstract: The paper describes a new model of discontinuous dynamic recrystallization (DDRX) which can operate in constant or variable thermomechanical conditions. The model considers the elementary physical phenomena at the grain scale such as strain hardening, recovery, grain boundary migration, and nucleation. The microstructure is represented through a set of representative grains defined by their size and dislocation density. It is linked to a constitutive law giving access to the polycrystal flow stress. Interaction between representative grains and the surrounding material is idealized using a two-site approach whereby two homogeneous equivalent media with different dislocation densities are considered. Topological information is incorporated into the model by prescribing the relative weight of these two equivalent media as a function of their volume fractions. This procedure allows accounting for the well-known necklace structures. The model is applied to the prediction of DDRX in 304 L stainless steel, with parameters identified using an inverse methodology based on a genetic algorithm. Results show good agreement with experimental data at different temperatures and strain rates, predicting recrystallization kinetics, recrystallized grain size and stress-strain curve. Parameters identified with one initial grain size lead to accurate results for another initial grain size without introducing any additional parameter.

Flow softening and dynamic recrystallization behavior of BT9 titanium alloy: a study using process map development

Czech Academy of Sciences Publication Activity Database

Ghasemi, E.; Zarei-Hanzaki, A.; Farabi, E.; Tesař, Karel; Jäger, Aleš; Rezaee, M.

2017-01-01

Roč. 695, Feb (2017), s. 1706-1718 ISSN 0925-8388 R&D Projects: GA ČR GBP108/12/G043 Institutional support: RVO:68378271 Keywords : titanium alloys * hot compression * processing map * dynamic recrystallization * electron backscatter diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.133, year: 2016

Recrystallization

International Nuclear Information System (INIS)

Guillope, Michel.

1979-01-01

The term recrystallization covers a vast subject in metallurgy. It involves varied and sometimes very different phenomena of which, however, the common points lie in a change of shape and/or size and/or the orientation of the initial grains. Hence, recrystallization is a structural phase transformation, in the solide state. Recrystallization uses one or both the following fundamental mechanisms, namely the creation of grain boundaries, the migration of grain boundaries. This can occur during plastic deformation and will then be termed dynamic. When it occurs without mechanical stress, whilst the temperature is maintained (or annealing), it is termed static. Recrystallization phenomena are divided schematically into two categories: the first particularly concerns the base mechanism, for example nucleation and grain boundary migration, the others treat the substance from a more global angle by analyzing the kinetic change in the grain size or by determining the orientations of the grain of the polycrystal (or texture). These two types of study form the poles of this course [fr

The effect of recrystallization on corrosion and electrochemical behavior of 7150 Al alloy

Energy Technology Data Exchange (ETDEWEB)

Peng, G.S.; Chen, K.H.; Fang, H.C.; Chen, S.Y.; Chao, H. [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China)

2011-01-15

By weight loss, potentiodynamic polarization, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) techniques complemented by optical and scanning electron microscopy observations, the effect of recrystallization on the corrosion, and electrochemical behavior of 7150 Al alloy was studied. The results indicated that the high recrystallization fraction 7150-1 was worse than the low recrystallization fraction 7150-2 on corrosion resistance. The analysis of EIS indicated that 7150-1 exhibited obvious pitting corrosion at 5 h immersion time, whereas 7150-2 showed no obvious pitting corrosion even at 33 h. The corrosion route developed along the grain boundary of recrystallization grains, not along the grain boundary of unrecrystallization grains. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of initial grain size on dynamic recrystallization in high purity austenitic stainless steels

International Nuclear Information System (INIS)

El Wahabi, M.; Gavard, L.; Montheillet, F.; Cabrera, J.M.; Prado, J.M.

2005-01-01

The influence of initial microstructure on discontinuous dynamic recrystallization (DDRX) has been investigated by using high purity and ultra high purity austenitic stainless steels with various initial grain sizes. After uniaxial compression tests at constant strain rates and various temperatures, the steady state microstructure or the state corresponding to the maximum strain (ε = 1) attained in the test was analyzed by scanning electron microscopy aided with automated electron back scattering diffraction. Recrystallized grain size d rec and twin boundary fraction f TB measurements were carried out. The mechanical behavior was also investigated by comparing experimental stress-strain curves with various initial grain sizes. DDRX kinetics was described by the classical Avrami equation. It was concluded that larger initial grain sizes promoted a delay in the DDRX onset in the two alloys. It was also observed that the softening process progressed faster for smaller initial grain sizes. The effect of initial grain size is larger in the HP material and becomes more pronounced at low temperature

Mesoscale modeling and simulation of microstructure evolution during dynamic recrystallization of a Ni-based superalloy

Energy Technology Data Exchange (ETDEWEB)

Chen, Fei [University of Nottingham, Department of Mechanical, Materials and Manufacturing Engineering, Nottingham (United Kingdom); Shanghai Jiao Tong University, Institute of Forming Technology and Equipment, Shanghai (China); Cui, Zhenshan [Shanghai Jiao Tong University, Institute of Forming Technology and Equipment, Shanghai (China); Ou, Hengan [University of Nottingham, Department of Mechanical, Materials and Manufacturing Engineering, Nottingham (United Kingdom); Long, Hui [University of Sheffield, Department of Mechanical Engineering, Sheffield (United Kingdom)

2016-10-15

Microstructural evolution and plastic flow characteristics of a Ni-based superalloy were investigated using a simulative model that couples the basic metallurgical principle of dynamic recrystallization (DRX) with the two-dimensional (2D) cellular automaton (CA). Variation of dislocation density with local strain of deformation is considered for accurate determination of the microstructural evolution during DRX. The grain topography, the grain size and the recrystallized fraction can be well predicted by using the developed CA model, which enables to the establishment of the relationship between the flow stress, dislocation density, recrystallized fraction volume, recrystallized grain size and the thermomechanical parameters. (orig.)

Effects of homogenization treatment on recrystallization behavior of 7150 aluminum sheet during post-rolling annealing

International Nuclear Information System (INIS)

Guo, Zhanying; Zhao, Gang; Chen, X.-Grant

2016-01-01

The effects of two homogenization treatments applied to the direct chill (DC) cast billet on the recrystallization behavior in 7150 aluminum alloy during post-rolling annealing have been investigated using the electron backscatter diffraction (EBSD) technique. Following hot and cold rolling to the sheet, measured orientation maps, the recrystallization fraction and grain size, the misorientation angle and the subgrain size were used to characterize the recovery and recrystallization processes at different annealing temperatures. The results were compared between the conventional one-step homogenization and the new two-step homogenization, with the first step being pretreated at 250 °C. Al_3Zr dispersoids with higher densities and smaller sizes were obtained after the two-step homogenization, which strongly retarded subgrain/grain boundary mobility and inhibited recrystallization. Compared with the conventional one-step homogenized samples, a significantly lower recrystallized fraction and a smaller recrystallized grain size were obtained under all annealing conditions after cold rolling in the two-step homogenized samples. - Highlights: • Effects of two homogenization treatments on recrystallization in 7150 Al sheets • Quantitative study on the recrystallization evolution during post-rolling annealing • Al_3Zr dispersoids with higher densities and smaller sizes after two-step treatment • Higher recrystallization resistance of 7150 sheets with two-step homogenization

Dynamic Recrystallization Behavior of AISI 422 Stainless Steel During Hot Deformation Processes

Science.gov (United States)

Ahmadabadi, R. Mohammadi; Naderi, M.; Mohandesi, J. Aghazadeh; Cabrera, Jose Maria

2018-02-01

In this work, hot compression tests were performed to investigate the dynamic recrystallization (DRX) process of a martensitic stainless steel (AISI 422) at temperatures of 950, 1000, 1050, 1100 and 1150 °C and strain rates of 0.01, 0.1 and 1 s-1. The dependency of strain-hardening rate on flow stress was used to estimate the critical stress for the onset of DRX. Accordingly, the critical stress to peak stress ratio was calculated as 0.84. Moreover, the effect of true strain was examined by fitting stress values to an Arrhenius type constitutive equation, and then considering material constants as a function of strain by using a third-order polynomial equation. Finally, two constitutive models were used to investigate the competency of the strain-dependent constitutive equations to predict the flow stress curves of the studied steel. It was concluded that one model offers better precision on the flow stress values after the peak stress, while the other model gives more accurate results before the peak stress.

Recrystallization in Commercially Pure Aluminum

DEFF Research Database (Denmark)

Bay, Bent; Hansen, Niels

1984-01-01

Recrystallization behavior in commercial aluminum with a purity of 99.4 pct was studied by techniques such as high voltage electron microscopy, 100 kV transmission electron microscopy, and light microscopy. Sample parameters were the initial grain size (290 and 24 microns) and the degree of defor......Recrystallization behavior in commercial aluminum with a purity of 99.4 pct was studied by techniques such as high voltage electron microscopy, 100 kV transmission electron microscopy, and light microscopy. Sample parameters were the initial grain size (290 and 24 microns) and the degree...... are discussed and compared with results from an earlier study1 covering the recrystallization behavior of commercial aluminum of the same purity deformed at higher degrees of deformation (50 to 90 pct reduction in thickness by cold-rolling)....

Rate controlling mechanisms during hot deformation of Mg–3Gd–1Zn magnesium alloy: Dislocation glide and climb, dynamic recrystallization, and mechanical twinning

International Nuclear Information System (INIS)

Mirzadeh, H.; Roostaei, M.; Parsa, M.H.; Mahmudi, R.

2015-01-01

Highlights: • Hot deformation behavior and dynamic recrystallization of GZ31 magnesium alloy. • Deducing the operative deformation mechanisms by constitutive analysis. • Viscous glide as the rate controlling step during hot working of GZ31 alloy. • Characterization of the effect of mechanical twinning on constitutive relations. - Abstract: The flow behavior of the Mg–3Gd–1Zn (GZ31) magnesium alloy during hot working was critically analyzed and dislocation glide in the form of a viscous drag process (viscous glide) was identified as the rate controlling mechanism due to interaction of rare earth Gd atoms with the moving dislocations. Mechanical twinning was shown to significantly affect the level of flow stress at high Zener–Hollomon parameters, i.e. low forming temperatures and high strain rates. Moreover, dynamic recrystallization (DRX) was found to be another responsible phenomenon for deviation of constitutive equations from the theoretical ones, namely the deformation activation energy based on diffusivity and the pre-defined Garofalo’s type hyperbolic sine power, during high-temperature thermomechanical processing of this creep resistant light alloy

Investigation of nucleation processes during dynamic recrystallization of ice using cryo-EBSD.

Science.gov (United States)

Chauve, T; Montagnat, M; Barou, F; Hidas, K; Tommasi, A; Mainprice, D

2017-02-13

Nucleation mechanisms occurring during dynamic recrystallization play a crucial role in the evolution of microstructures and textures during high temperature deformation. In polycrystalline ice, the strong viscoplastic anisotropy induces high strain heterogeneities between grains which control the recrystallization mechanisms. Here, we study the nucleation mechanisms occurring during creep tests performed on polycrystalline columnar ice at high temperature and stress (T=-5°C;σ=0.5 MPa) by post-mortem analyses of deformation microstructures using cryogenic electron backscatter diffraction. The columnar geometry of the samples enables discrimination of the nuclei from the initial grains. Various nucleation mechanisms are deduced from the analysis of the nuclei relations with the dislocation sub-structures within grains and at grain boundaries. Tilt sub-grain boundaries and kink bands are the main structures responsible for development of polygonization and mosaic sub-structures. Nucleation by bulging at serrated grain boundaries is also an efficient nucleation mechanism near the grain boundaries where strain incompatibilities are high. Observation of nuclei with orientations not related to the 'parent' ones suggests the possibility of 'spontaneous' nucleation driven by the relaxation of the dislocation-related internal stress field. The complexity of the nucleation mechanisms observed here emphasizes the impact of stress and strain heterogeneities on dynamic recrystallization mechanisms.This article is part of the themed issue 'Microdynamics of ice'. © 2016 The Author(s).

Modelling and simulation of dynamic recrystallization (DRX) in OFHC copper at very high strain rates

Science.gov (United States)

Testa, G.; Bonora, N.; Ruggiero, A.; Iannitti, G.; Persechino, I.; Hörnqvist, M.; Mortazavi, N.

2017-01-01

At high strain rates, deformation processes are essentially adiabatic and if the plastic work is large enough dynamic recrystallization can occur. In this work, an examination on microstructure evolution of OFHC copper in Dynamic Tensile Extrusion (DTE) test, performed at 400 m/s, was carried out. EBSD investigations, along the center line of the fragment remaining in the extrusion die, showed a progressive elongation of the grains, and an accompanying development of a strong + dual fiber texture. Discontinuous dynamic recrystallization (DRX) occurred at larger strains, and it was showed that nucleation occurred during straining. A criterion for DRX to occur, based on the evolution of Zener-Hollomon parameter during the dynamic deformation process, is proposed. Finally, DTE test was simulated using the modified Rusinek-Klepaczko constitutive model incorporating a model for the prediction of DRX initiation.

Dynamical recrystallization of high purity austenitic stainless steels; Recristallisation dynamique d'aciers inoxydables austenitiques de haute purete

Energy Technology Data Exchange (ETDEWEB)

Gavard, L

2001-01-01

The aim of this work is to optimize the performance of structural materials. The elementary mechanisms (strain hardening and dynamical regeneration, germination and growth of new grains) occurring during the hot working of metals and low pile defect energy alloys have been studied for austenitic stainless steels. In particular, the influence of the main experimental parameters (temperature, deformation velocity, initial grain size, impurities amount, deformation way) on the process of discontinuous dynamical recrystallization has been studied. Alloys with composition equal to those of the industrial stainless steel-304L have been fabricated from ultra-pure iron, chromium and nickel. Tests carried out in hot compression and torsion in order to cover a wide range of deformations, deformation velocities and temperatures for two very different deformation ways have allowed to determine the rheological characteristics (sensitivity to the deformation velocity, apparent activation energy) of materials as well as to characterize their microstructural deformations by optical metallography and electron back-scattered diffraction. The influence of the initial grain size and the influence of the purity of the material on the dynamical recrystallization kinetics have been determined. An analytical model for the determination of the apparent mobility of grain boundaries, a semi-analytical model for the dynamical recrystallization and at last an analytical model for the stationary state of dynamical recrystallization are proposed as well as a new criteria for the transition between the refinement state and the state of grain growth. (O.M.)

Plasticity-mediated collapse and recrystallization in hollow copper nanowires: a molecular dynamics simulation

Directory of Open Access Journals (Sweden)

Amlan Dutta

2016-02-01

Full Text Available We study the thermal stability of hollow copper nanowires using molecular dynamics simulation. We find that the plasticity-mediated structural evolution leads to transformation of the initial hollow structure to a solid wire. The process involves three distinct stages, namely, collapse, recrystallization and slow recovery. We calculate the time scales associated with different stages of the evolution process. Our findings suggest a plasticity-mediated mechanism of collapse and recrystallization. This contradicts the prevailing notion of diffusion driven transport of vacancies from the interior to outer surface being responsible for collapse, which would involve much longer time scales as compared to the plasticity-based mechanism.

Relationship of Technological Properties with Dynamic Recrystallization of Quartz on the Example of Objects of the Karelian-Kola Region

Science.gov (United States)

Skamnitskaya, Lubov; Rakov, Leonid; Bubnova, Tatyana; Shchiptsov, Vladimir

2017-12-01

Despite the significant reserves of quartz raw materials, there is a deficit of high purity quartz. It is due to the strict technical requirements imposed by standards for this type of raw materials and technological properties of quartz, which are determined by the features of the crystal structure. The crystalline structure is of particular importance for the technological properties of quartz, since such important characteristics as the limit of raw material enrichment, dissolution rate in acid, melting point of quartz, etc., are determined. The formation of the crystal structure of quartz under natural conditions is associated with the successive dynamic recrystallization of the mineral. The degree of dynamic recrystallization of quartz reflects the distribution of dispersed impurities. If it is weakly manifested, the dispersed impurities are not displaced from one zone to another, and all quartz microblocks contain approximately the same concentration. In this case, more or less uniform dissolution of various regions of quartz is observed, and the pattern of distribution of submicroscopic inhomogeneities is monotonic. If intensive dynamic recrystallization of quartz takes place, then it causes a significant redistribution of the scattered impurities. Then the treatment in HF leads to the appearance of a contrast pattern of the distribution of submicroscopic inhomogeneities. The details of the crystal structure of quartz in this work were investigated by the electron paramagnetic resonance (EPR) method using the ER-420 “Bruker” spectrometer. In the selected samples of quartz, the concentrations of isomorphic impurities Al and Ti were measured, and the degree of crystallinity D of the mineral was estimated from the EPR spectra of each of them. Thus, the technological properties of quartz are determined by various geological processes. The results of the studies show that when evaluating the prospects of quartz raw materials, it is necessary to take into

Microstructures and recrystallization behavior of severely hot-deformed tungsten

International Nuclear Information System (INIS)

Mathaudhu, S.N.; De Rosset, A.J.; Hartwig, K.T.; Kecskes, L.J.

2009-01-01

When coarse-grained (CG) tungsten (W) is heavily worked by equal-channel angular extrusion (ECAE), the grain size is reduced to the ultrafine-grained/nanocrystalline regimes (UFG/NC) and the strength and ductility increase. Because of the brittle nature of CG W, the material must be hot-extruded, and, if the temperatures are near the recrystallization temperature (T rc ), gains in properties may not be maximized. In this study, the recrystallization behavior of ECAE-processed CG W is examined as a function of the imparted strain (i.e., number of extrusions) and the hot-working extrusion temperature. Up to four ECAE passes were performed in tooling with a 90 deg. channel intersection, and at temperatures of 1000 deg. C or 1200 deg. C. Subsequent 60 min annealing of the worked material to 1600 deg. C allowed for the determination of T rc . Vickers microhardness measurements and scanning electron microscopy, were used to characterize the microstructures in the as-worked and recrystallized states. The ECAE-processed W shows increased microstructural break-up and refinement with increasing strain and decreasing hot-working temperature in the fully worked state. T rc was determined to be ∼1400 deg. C, which is nearly independent of the number of extrusions and the working temperature. These results show that if ECAE is accomplished below 1400 deg. C (i.e., at 1000 deg. C or lower) the attractive properties of the UFG/NC-worked W may be retained. Specifically, below 1000 deg. C, with increasing strain imparted to the material, high hardness values with a concomitant grain size refinement (∼350 nm) could be expected

Effect of strain on evolution of dynamic recrystallization in Nb-1 wt%Zr-0.1 wt%C alloy at 1500 and 1600 °C

Energy Technology Data Exchange (ETDEWEB)

Behera, A.N. [Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Homi Bhabha National Institute, Anushakti Nagar, Mumbai 400094 (India); Kapoor, R., E-mail: rkapoor@barc.gov.in [Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Homi Bhabha National Institute, Anushakti Nagar, Mumbai 400094 (India); Paul, B. [Materials Processing & Corrosion Engineering Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Chakravartty, J.K. [Mechanical Metallurgy Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2017-04-15

Uniaxial compression tests were carried out on Nb-1 wt%Zr-0.1 wt%C alloy at temperature of 1500 and 1600 °C and strain rate of 0.1 s{sup −1} to study the evolution of dynamic recrystallization with strain. Electron back scatter diffraction was used to quantify the microstructural evolution. Nb-1Zr-0.1C alloy showed a necklace structure at a strain of 0.9 when deformed at 1500 °C and at strain of 0.6 when deformed at 1600 °C, both at strain rate of 0.1 s{sup −1}. This suggested the occurrence of dynamic recrystallization. At 1500 °C and strain of 0.9 the local average misorientation and the grain orientation spread was low confirming the presence of dynamic recrystallization at this deformation condition. At both 1500 and 1600 °C and all measured strains the recrystallized grains had a strong fiber component of <001>. - Highlights: • Necklace formation of dynamically recrystallized grains occurred at strain of 0.6 and 0.9 for 1500 and 1600 °C, respectively. • Equiaxed microstructures were seen with increase in strain for both 1500 and 1600 °C. • At large strains the predominant recrystallized texture evolved to <001> pole.

Dynamic recrystallization of a new nickel-based alloy for 700 °C A-USC power plant applications with different initial states: as-homogenized and as-forged

Energy Technology Data Exchange (ETDEWEB)

Wu, Yunsheng [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhang, Maicang, E-mail: mczhang@ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Xie, Xishan [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Lin, Fusheng; Zhao, Shuangqun [Shanghai Power Equipment Research Institute, Shanghai 200240 (China)

2016-04-26

The hot deformation behavior of a new-designed nickel-based alloy with different initial states were investigated by isothermal compression at temperature range of 1000–1200 °C with strain rate of 0.01–20 s{sup −1} and nominal strain of 15–70% on a Gleeble-1500 thermo-mechanical simulator. The correlation of dynamic recrystallization (DRX) mechanism and initial alloy states as well as deformation parameters were analyzed in detail by means of transmission electron microscope (TEM) and electron backscattered diffraction (EBSD). For homogenized alloy with extremely large grains, the DRX mechanism transforms partly from discontinuous dynamic recrystallization (DDRX) characterized with serrated and bulging grain boundary into continuous dynamic recrystallization (CDRX) operated by progressive sub-grain merging and rotation with the increasing strain rate and decreasing deformation temperature, which results from the poor deformation compatibility in the alloy with extremely large grains. However, the dominant DRX mechanism in as-forged alloy is DDRX almost at all the deformation conditions, and CDRX is only an assistant mechanism, which caused by the initial inhomogeneous dislocation distribution and fine grains. In consequence, the initial alloy states have a significant influence on the DRX, which cannot be ignored in the hot deformation research.

Simulation of the hot flow behaviour of a medium carbon microalloyed steel. Part 2. Dynamic recrystallization: onset and kinetics

International Nuclear Information System (INIS)

Cabrera, J.M.; Al Omar, A.; Prado, J.M.

1997-01-01

According to the part 1 of this work, in this second part the dynamic recrystallization of a commercial medium carbon microalloyed steel is characterized from the point of view of its onset and kinetics. For this purpose uniaxial hot compression tests were carried out over a range of five orders of magnitude in strain rate and 300 degree centigree of temperature. Experimental results are compared with those reported in the literature and the possible effect of dynamic precipitation is also analyzed. It is verified that the kinetics of dynamics recrystallization can balefully be described by the classical Avrami equation. (Author) 42 refs

A Behavioral Analysis of the Laboratory Learning Process: Redesigning a Teaching Unit on Recrystallization.

Science.gov (United States)

Mulder, T.; Verdonk, A. H.

1984-01-01

Reports on a project in which observations of student and teaching assistant behavior were used to redesign a teaching unit on recrystallization. Comments on the instruction manual, starting points for teaching the unit, and list of objectives with related tasks are included. (JN)

Recrystallization resistance in aluminum alloys containing zirconium

International Nuclear Information System (INIS)

Ranganathan, K.

1991-01-01

Zirconium forms a fine dispersion of the metastable β' (Al 3 Zr) phase that controls recrystallization by retarding the motion of high-angle boundaries. The primary material chosen for this research was aluminum alloy 7150 containing zinc, magnesium, and copper as the major solute elements and zirconium as the dispersoid-forming element. The size, distribution, and the volume fraction of β' was controlled by varying the alloy composition and preheat practices. Preheated ingots were subjected to a specific sequence of hot-rolling operations to evaluate the resistance to recrystallization of the different microstructures. Optical and transmission electron microscopy (TEM) techniques were used to investigate the influence of dispersoid morphology resulting from the thermal treatments and deformation processing on the recrystallization behavior of the alloy. Studies were conducted to determine the influence of the individual solute elements present in 7150 on the precipitation of β' and consequently on the recrystallization behavior of the material. These studies were done on compositional variants of commercial 7150

On the grain boundary character distribution of Incoloy 800H during dynamic recrystallization

Energy Technology Data Exchange (ETDEWEB)

Cao, Yu, E-mail: vieri32825@126.com [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China); Di, Hongshuang [State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819 (China); Huang, Guangjie [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China)

2017-04-01

In this paper, we investigated the influence of hot deformation parameters on the distribution and proliferation of twin boundaries during dynamic recrystallization (DRX). The results showed that microstructure evolution is characterized by a process of “dynamic recovery (DRV)→necklace/multiple necklace→fully DRX” with increasing temperature and decreasing strain rate. The predominant proliferation mechanism of Σ3{sup n} (1 ≤ n ≤ 3) boundaries is transformed from Σ3 regeneration to new twinning during the growth of DRX grains.

On the grain boundary character distribution of Incoloy 800H during dynamic recrystallization

International Nuclear Information System (INIS)

Cao, Yu; Di, Hongshuang; Huang, Guangjie

2017-01-01

In this paper, we investigated the influence of hot deformation parameters on the distribution and proliferation of twin boundaries during dynamic recrystallization (DRX). The results showed that microstructure evolution is characterized by a process of “dynamic recovery (DRV)→necklace/multiple necklace→fully DRX” with increasing temperature and decreasing strain rate. The predominant proliferation mechanism of Σ3 n (1 ≤ n ≤ 3) boundaries is transformed from Σ3 regeneration to new twinning during the growth of DRX grains.

Dynamic recrystallization mechanisms and their transition in the Daling Thrust (DT) zone, Darjeeling-Sikkim Himalaya

Science.gov (United States)

Ghosh, Subhajit; Bose, Santanu; Mandal, Nibir; Dasgupta, Sujoy

2016-04-01

The Daling Thrust (DT) delineates a zone of intense shear localization in the Lesser Himalayan Sequence (LHS) of the Darjeeling-Sikkim Himalaya. From microstructural studies of deformed quartzite samples, we show a transition in the dynamic recrystallization mechanism with increasing distance from the DT, dominated by grain boundary bulging (BLG) recrystallization closest to the DT, and progressively replaced by sub-grain rotation (SGR) recrystallization away from the thrust. The transition is marked by a characteristic variation in the fractal dimension (D) of grain boundaries, estimated from the area-perimeter method. For the BLG regime, D ≈ 1.046, which decreases significantly to a value as low as 1.025 for the SGR regime. Using the available thermal data for BLG and SGR recrystallization, we infer increasing deformation temperatures away from the DT in the hanging wall. Based on the quartz piezometer our estimates reveal strong variations in the flow stress (59.00 MPa to 16.00 MPa) over a distance of 1.2 km from the DT. Deformation mechanism maps constructed for different temperatures indicate that the strain rates (10- 12 S- 1 to 10- 14 S- 1) comply with the geologically possible range. Finally, we present a mechanical model to provide a possible explanation for the cause of stress intensification along the DT.

Temperature dependence of dynamic behavior of commercially pure titanium by the compression test

International Nuclear Information System (INIS)

Lee, Su Min; Seo, Song Won; Park, Kyoung Joon; Min, Oak Key

2003-01-01

The mechanical behavior of a Commercially Pure Titanium (CP-Ti) is investigated at high temperature Split Hopkinson Pressure Bar (SHPB) compression test with high strain-rate. Tests are performed over a temperature range from room temperature to 1000 .deg. C with interval of 200 deg. C and a strain-rate range of 1900∼2000/sec. The true flow stress-true strain relations depending on temperature are achieved in these tests. For construction of constitutive equation from the true flow stress-true strain relation, parameters for the Johnson-Cook constitutive equation is determined. And the modified Johnson-Cook equation is used for investigation of behavior of flow stress in vicinity of recrystallization temperature. The modified Johnson-Cook constitutive equation is more suitable in expressing the dynamic behavior of a CP-Ti at high temperature, i.e. about recrystallization temperature

Study of secondary recrystallization in grain-oriented steel treated under dynamical heat treatment conditions

Directory of Open Access Journals (Sweden)

V. Stoyka

2009-04-01

Full Text Available The present study was made to investigate secondary recrystallization in grain-oriented steels annealed at short time temperature exposures with application of dynamical heating. The investigated GO steels for experiments were taken from one industrial line after final cold rolling reduction and subsequent box annealing. It was shown that application of short time heat treatment conditions could lead to complete abnormal grain growth in the investigated GO steel. The texture and microstructure obtained in the laboratory treated material is similar to that observed in the same GO steel taken after industrial final box-annealing. However, some “parasitic” grains were observed in the secondary recrystallized matrix of the laboratory treated GO steel. These “parasitic” grains possess the unwanted from magnetic properties point of view {111} orientation components.

Deformation Behavior of Al0.25CoCrFeNi High-Entropy Alloy after Recrystallization

Directory of Open Access Journals (Sweden)

Jinxiong Hou

2017-03-01

Full Text Available Cold rolling with subsequent annealing can be used to produce the recrystallized structure in high entropy alloys (HEAs. The Al0.25CoCrFeNi HEAs rolled to different final thickness (230, 400, 540, 800, 1000, 1500 μm are prepared to investigate their microstructure evolutions and mechanical behaviors after annealing. Only the single face-centered cubic phase was obtained after cold rolling and recrystallization annealing at 1100 °C for 10 h. The average recrystallized grain size in this alloy after annealing ranges from 92 μm to 136 μm. The annealed thin sheets show obviously size effects on the flow stress and formability. The yield strength and tensile strength decrease as t/d (thickness/average grain diameter ratio decreases until the t/d approaches 2.23. In addition, the stretchability (formability decreases with the decrease of the t/d ratio especially when the t/d ratio is lower than about 6. According to the present results, yield strength can be expressed as a function of the t/d ratio.

Effect of strain and deformation route on grain boundary characteristics and recrystallization behavior of aluminum

International Nuclear Information System (INIS)

Sakai, Tetsuo; Takahashi, Yasuo; Utsunomiya, Hiroshi

2014-01-01

The effect of strain and deformation route on the recrystallization behavior of aluminum sheets has been investigated using well lubricated cold rolling and continuous equal channel angular extrusion. Three different deformation routes in plane strain corresponding to (1) simple shear, (2) compression, and (3) the combination of simple shear and compression were performed on 1100 aluminum sheet. Fixed amounts of the equivalent strain of 1.28 and 1.06 were accumulated in each route. In case of the combined deformation route, the ratio of shear strain to the total equivalent strain was varied. The recrystallized grain size was finer if the combined deformation route was employed instead of the monotonic route under the same amount of equivalent strain at either strain level. The density of high angle grain boundaries that act as nucleation sites for recrystallization was higher in materials deformed by the combined route. The orientation imaging micrographs revealed that the change in deformation route is effective for introducing a larger number of new high angle grain boundaries with relatively low misorientation angle

Effect of strain and deformation route on grain boundary characteristics and recrystallization behavior of aluminum

Science.gov (United States)

Sakai, Tetsuo; Utsunomiya, Hiroshi; Takahashi, Yasuo

2014-08-01

The effect of strain and deformation route on the recrystallization behavior of aluminum sheets has been investigated using well lubricated cold rolling and continuous equal channel angular extrusion. Three different deformation routes in plane strain corresponding to (1) simple shear, (2) compression, and (3) the combination of simple shear and compression were performed on 1100 aluminum sheet. Fixed amounts of the equivalent strain of 1.28 and 1.06 were accumulated in each route. In case of the combined deformation route, the ratio of shear strain to the total equivalent strain was varied. The recrystallized grain size was finer if the combined deformation route was employed instead of the monotonic route under the same amount of equivalent strain at either strain level. The density of high angle grain boundaries that act as nucleation sites for recrystallization was higher in materials deformed by the combined route. The orientation imaging micrographs revealed that the change in deformation route is effective for introducing a larger number of new high angle grain boundaries with relatively low misorientation angle.

Processing Map and Recrystallization Diagram for GH984G18 Alloy

Directory of Open Access Journals (Sweden)

XIE Bi-jun

2016-09-01

Full Text Available The thermal compression experiment of GH984G18 alloy was carried out using thermal-mechanical testing machines Gleeble3800. Based on the stress-strain curves obtained from the experiments, the processing maps of the GH984G18 alloy were established according to the dynamic materials model (DMM, then the hot working process window of alloy was built, and the influence of temperature and strain on the dynamic recrystallization of the experimental alloy was also analyzed. The results show that when the strain is small(ε≤0.2, the optimum deformation temperature is in the temperature range of 1030-1090℃ and strain rate range of 0.01-0.18s-1; with the increase of strain(ε≥0.3, the optimum deformation temperature moves to the high temperature range of 1180-1200℃ and strain rate range of 0.056-0.25s-1; and at the strain rate of 1s-1, dynamic recrystallization does not occur and dynamic recovery dominates when the temperature is lower than 900℃; and partial dynamic recrystallization occurs at the temperature of 1000℃ and the strain of 30%; and then the complete dynamic recrystallization occurs at the temperature of 1000℃ and strain of 60%.

Effects of heterogeneity on recrystallization kinetics of nanocrystalline copper prepared by dynamic plastic deformation

DEFF Research Database (Denmark)

Lin, Fengxiang; Zhang, Yubin; Tao, Nairong

2014-01-01

to develop a heterogeneous structure, consisting of regions with different textures and microstructures. This heterogeneity within the deformed structure leads to the formation of severely clustered grains in partially recrystallized samples. The recrystallization kinetic curve shows an Avrami exponent less...... recrystallization kinetics. The hardness of the two samples was measured, and the mechanical properties before and after partial recrystallization of both samples are discussed based on the presence of structural heterogeneities on the macroscopic and the microscopic scale....

Effect of Primary Recrystallized Microstructure and Nitriding on Secondary Recrystallization in Grain Oriented Silicon Steel by Low Temperature Slab Reheating

Directory of Open Access Journals (Sweden)

LIU Gong-tao

2018-01-01

Full Text Available Different primary recrystallized grain sizes were obtained by controlling decarburization process in grain oriented silicon steel produced by low temperature slab reheating technique. The effect of primary grain size on secondary recrystallization and magnetic properties was studied. The appropriate nitrogen content after nitriding was explored in case of very large primary grain size, and the effect of {411}〈148〉 primary recrystallized texture on the abnormal growth behavior was discussed. The results show that an increase in average primary grain size from 10μm to 15μm leads to an increase of secondary recrystallization temperature and a sharper Goss texture with higher magnetic permeability, in the condition of a very large average primary grain size of 28μm, the suitable amount of nitrogen increases to about 6×10-4. The {411}〈148〉 oriented grains in primary recrystallized microstructure can easily grow into larger sizes due to their size advantage, and thus hinder the abnormal growth of secondary grains, moreover, the hindering effect is more pronounced in the abnormal growth of Brass-oriented grains due to their misorientation with low migration rate other than Goss grains.

Recrystallization of deformed copper - kinetics and microstructural evolution

DEFF Research Database (Denmark)

Lin, Fengxiang

The objective of this study is to investigate the recrystallization kinetics and microstructural evolution in copper deformed to high strains, including copper deformed by cold-rolling and copper deformed by dynamic plastic deformation (DPD). Various characterization techniques were used, including...... electron backscatter diffraction (EBSD), Vickers hardness test, 3D X-ray diffraction (3DXRD) and differential scanning calorimetry (DSC). For the cold-rolled samples, a series of initial parameters was investigated for their effects on the recrystallization kinetics and textures, including initial grain...

COMPETITION BEETWEN DYNAMIC RECUPERATION AND RECRYSTALLIZATION OF ASTM F 138 AUSTENITIC STAINLESS STEEL UTILIZED IN MEDICAL DEVICES

Directory of Open Access Journals (Sweden)

Fabio Henrique Casarini Geronimo

2013-06-01

Full Text Available ASTM F 138 austenitic stainless steel has being used in the manufacture of orthopedical devices by hot forging. In this work, the flow stress curves are determined by hot torsion tests in a wide range of temperatures and strain rates. With the observed microestrutural evolution by optical microscopy in different hot forming conditions in addiction with EBSD (Electron Backscatter Diffraction techniques it is possible to obtained the recrystallized volume fraction and the misorientation angles of the samples. Due to the intermediate level of stacking fault energy of this material, during the dynamic softening occurs a competition between recrystallization and recovery. The aim of this work is to identify the softening mechanisms in this stainless steel, as well as in which hot work conditions they become more active.

Creep in single crystals of γ single phase Ni-20Cr alloy and evolution of dynamic recrystallization

International Nuclear Information System (INIS)

Matsuo, T.; Terada, Y.; Takahashi, S.; Ishiwari, Y.

2000-01-01

The creep rate - time and the creep rate - strain curves of the single crystals of γ single phase Ni-20 mass%Cr alloy have been investigated at 1173 K under the wide stress range of 19.6 to 98 MPa, and compared with those of polycrystals. The orientation corresponding to the stress axis of the single crystals were chosen within the standard stereographic triangle. The creep curve in the Ni-20 mass%Cr single crystal consists of a transient stage and an accelerating stage without a steady state stage. The transient stage has two steps. In the first step, the creep rate slightly decreases, and in the second step, the decrease in creep rate becomes prominent with increasing the testing time. With decreasing the stress, the extension of transient stage becomes prominent, and by this extension, the decreasing ratio of the creep rate in transient stage is enlarged. At the lowest stress of 19.6 MPa, the most prominent extension of transient stage and the more than two order decrease in creep rate in transient stage are detected. The creep interrupting tests have been conducted at the stress of 29.4 MPa in the strain range of 0.1 to 0.6 to examine the appearance of dynamically recrystallized grains. At the strain of 0.1 corresponding to the end of the first step in transient stage, a straight subboundary parallel to slip plane appears in a wide distance of a few hundreds micrometers. With increasing the strain, the straight subboundary turns to waved one. At the strain showing the minimum creep rate, a lot of evolved subgrains appear. At the strain corresponding to the early stage of accelerating creep, dynamically recrystallized grains appear. It is confirmed that the onset of accelerating creep well corresponds to the appearance of dynamically recrystallized grains. In the single crystal creep ruptured, the whole gage portion turns to polycrystal with equiaxed grains having a diameter of 150 μm. (orig.)

Study on Recrystallization of Cold-worked and β-quenched zirconium alloys

International Nuclear Information System (INIS)

Goo, J. S.; Hong, S. I.; Kim, H. S.; Jeong, Y. H.

1998-01-01

The observation of microstructure and the hardness test of Zr-Sn binary and Zircaloy-4 alloys were performed to investigate the recrystallization of cold-worked and β-quenched Zr alloys. All specimens were heat-treated in vacuum condition at various temperatures. From the observation of microstructures of cold-worked and β-quenched Zr alloys, the cold-worked specimens were shown to keep the cold-worked micro- structure as annealing temperature increased up to 500 deg C and the recrystallization was completed at between 550 deg C and 700 deg C. Meanwhile, the recrystallization of β-quenched Zr alloys was started at about 700 deg C. In all specimens of cold-worked and β-quenched Zr alloys, the hardness value tended to be consistent with microstructure. Although the cold-worked and the β-quenched specimens had an equal initial hardness value, the recrystallization behavior was indicated to be different from each other, which means that recrystallization mechanism is different from each other

Simulations of boundary migration during recrystallization using molecular dynamics

DEFF Research Database (Denmark)

Godiksen, Rasmus Brauner; Trautt, Z.T.; Upmanyu, M.

2007-01-01

process is not uniform as assumed in many recrystallization models, but that the grain boundaries migrate in an irregular fashion and exhibit a strong dependence on the local presence of dislocations, which can distort the local migration process significantly. (c) 2007 Acta Materialia Inc. Published...

Recrystallization of freezable bound water in aqueous solutions of medium concentrations

Institute of Scientific and Technical Information of China (English)

赵立山; 潘礼庆; 纪爱玲; 曹则贤; 王强

2016-01-01

For aqueous solutions with freezable bound water, vitrification and recrystallization are mingled, which brings diffi-culty to application and misleads the interpretation of relevant experiments. Here, we report a quantification scheme for the freezable bound water based on the water-content dependence of glass transition temperature, by which also the concentra-tion range for the solutions that may undergo recrystallization finds a clear definition. Furthermore, we find that depending on the amount of the freezable bound water, different temperature protocols should be devised to achieve a complete recrys-tallization. Our results may be helpful for understanding the dynamics of supercooled aqueous solutions and for improving their manipulation in various industries.

Influence of macroscopic shear deformation on polygonization and recrystallization of molybdenum crystals

International Nuclear Information System (INIS)

Larikov, L.N.; Belyakova, M.N.; Maksimenko, E.A.; Mudruk, P.V.

1984-01-01

The effect of shear bands on polygonization and recrystallization is studied on molybdenum monocrystals deformed by compression. A sharp bend of the lattice is shown to be a structural condition necessary for arising the shear step. Internal stress relaxation strongly changes kinetics of softening processes in compressed molybdenum crystals: it slows down polygonization under low-temperature heating (below 700 deg C) and accelerates it under high-temperature heating (higher 1000 deg C). Under the effect of relaxation of internal streses recrystallization in the investigated crystals is similar to dynamical: recrystallized grains are distorted and they have a developed substructure

Effect of the strain rate in the dynamic recrystallization of ETP copper during its hot compression with descending temperatures; Efecto de la velocidad de deformacion en la recristalizacion dinamica de un cobre ETPdurante su compresion en caliente con temperatura descendente

Energy Technology Data Exchange (ETDEWEB)

Torrente, G.; Torres, M.; Sanoja, L.

2011-07-01

The main purpose of this project is to establish the effect of strain rate in the dynamic recrystallization of an ETP copper during its hot deformation with descending temperature. For this, there were made some tests of hot compression until true deformations close to one, with four strain rates while the temperature was descending. The tests that were made to the two lowest strain rates, showed a multiple peaks dynamic recrystallization with a rise of the tension instead it reaches the steady state, maybe due a continuous decline of the temperature.With the increase of rate the rest of the tests showed simple peak recrystallization and recovering respectively. The experimental results were compared with the results of a simulation based on the Damped Cosine Avrami Model. The simulation produced results closed to those measured during the multiple peaks dynamic recrystallization. These suggest that the application of this Model may be extended to multiple peaks dynamic recrystallization processes with changeable temperature. (Author) 33 refs.

Recrystallization texture in nickel heavily deformed by accumulative roll bonding

Science.gov (United States)

Mishin, O. V.; Zhang, Y. B.; Godfrey, A.

2017-07-01

The recrystallization behavior of Ni processed by accumulative roll bonding to a total accumulated von Mises strain of 4.8 has been examined, and analyzed with respect to heterogeneity in the deformation microstructure. The regions near the bonding interface are found to be more refined and contain particle deformation zones around fragments of the steel wire brush used to prepare the surface for bonding. Sample-scale gradients are also observed, manifested as differences between the subsurface, intermediate and central layers, where the distributions of texture components are different. These heterogeneities affect the progress of recrystallization. While the subsurface and near-interface regions typically contain lower frequencies of cube-oriented grains than anywhere else in the sample, a strong cube texture forms in the sample during recrystallization, attributed to both a high nucleation rate and fast growth rate of cube-oriented grains. The observations highlight the sensitivity of recrystallization to heterogeneity in the deformation microstructure and demonstrate the importance of characterizing this heterogeneity over several length scales.

3D Characterization of Recrystallization Boundaries

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andrew William; MacDonald, A. Nicole

2016-01-01

A three-dimensional (3D) volume containing a recrystallizing grain and a deformed matrix in a partially recrystallized pure aluminum was characterized using the 3D electron backscattering diffraction technique. The 3D shape of a recrystallizing boundary, separating the recrystallizing grain...... on the formation of protrusions/retrusions....

FRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY

Directory of Open Access Journals (Sweden)

M. S. Kaiser

2014-12-01

Full Text Available The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were also studied using JMAK type analysis to see if there exists any correlation between the methods. Recrystallization fraction behavior between two methods the scandium added alloys show the higher variation due to precipitation hardening and higher recrystallization behavior. The scandium and zirconium as a combined shows the more variation due to formation of Al3(Sc, Zr precipitate. From the microstructure it is also observed that the base Al-Mg alloy attained almost fully re-crystallized state after annealing at 400 °C for 60 minutes

Development of a Model for Dynamic Recrystallization Consistent with the Second Derivative Criterion

Directory of Open Access Journals (Sweden)

Muhammad Imran

2017-11-01

Full Text Available Dynamic recrystallization (DRX processes are widely used in industrial hot working operations, not only to keep the forming forces low but also to control the microstructure and final properties of the workpiece. According to the second derivative criterion (SDC by Poliak and Jonas, the onset of DRX can be detected from an inflection point in the strain-hardening rate as a function of flow stress. Various models are available that can predict the evolution of flow stress from incipient plastic flow up to steady-state deformation in the presence of DRX. Some of these models have been implemented into finite element codes and are widely used for the design of metal forming processes, but their consistency with the SDC has not been investigated. This work identifies three sources of inconsistencies that models for DRX may exhibit. For a consistent modeling of the DRX kinetics, a new strain-hardening model for the hardening stages III to IV is proposed and combined with consistent recrystallization kinetics. The model is devised in the Kocks-Mecking space based on characteristic transition in the strain-hardening rate. A linear variation of the transition and inflection points is observed for alloy 800H at all tested temperatures and strain rates. The comparison of experimental and model results shows that the model is able to follow the course of the strain-hardening rate very precisely, such that highly accurate flow stress predictions are obtained.

Mesoscopic simulation of recrystallization and grain growth

International Nuclear Information System (INIS)

Rollett, A.D.

2000-01-01

A brief summary of simulation techniques for recrystallization and grain growth is given. The available methods include surface evolver, front tracking (including finite element methods and vertex methods), networks of curves, phase field, cellular automata, and Monte Carlo. Two of the models that use a regular lattice, the Potts model and the Cellular Automaton (CA) model, have proved to be very useful. Microstructure is represented on a discrete lattice where the value of the field at each point represents the local orientation of the material and boundaries exist between points of unlike orientation. Two issues are discussed: one is a hybrid approach to combining the standard Monte Carlo and cellular automata algorithms for recrystallization modeling. The second is adaptation of the MC method for modeling grain growth (and recrystallization) with physically based boundary properties. Both models have significant limitations in their standard forms. The CA model is very useful and efficient for simulating recrystallization with deterministic motion of the recrystallization fronts. It can be adapted to simulate curvature driven migration provided that multiple sub-lattices are used with a probabilistic switching rule. The Potts model is very successful in modeling curvature driven boundary migration and grain growth. It does not simulate the proportionality between boundary velocity and a stored energy driving force, however, unless rather restricted conditions of stored energy (in relation to the grain boundary energy) and lattice temperature are satisfied. A new approach based on a hybrid of the Potts model (MC) and the Cellular Automaton (CA) model has been developed to obtain the desired limiting behavior for both curvature-driven and stored energy-driven grain boundary migration. The combination of methods is achieved by interleaving the two different types of reorientation event in time. The results show that the hybrid algorithm models the Gibbs

Mathematical modeling of phenomena of dynamic recrystallization during hot plastic deformation in high-carbon bainitic steel

Directory of Open Access Journals (Sweden)

T. Dembiczak

2017-01-01

Full Text Available Based on the research results, coefficients were determined in constitutive equations, describing the kinetics of dynamic recrystallization in high-carbon bainitic steel during hot deformation. The developed mathematical model takes into account the dependence of changing kinetics in the size evolution of the initial austenite grains, the value of strain, strain rate, temperature and time. Physical simulations were carried out on rectangular specimens measuring 10 × 15 × 20 mm. Compression tests with a plane state of deformation were carried out using a Gleeble 3800.

A Comparative Study on the Static Recrystallization Behavior of Cold-Rolled Mg-3Al-1Zn Alloy Stimulated by Electropulse Treatment and Conventional Heat Treatment

Science.gov (United States)

Li, Xiaopei; Li, Xiaohui; Kure-Chu, Song-Zhu; Tang, Guoyi

2018-02-01

Cold-rolled AZ31 Mg alloy strips, with a reduction of 33 pct, were subjected to electropulse treatment (EPT) and conventional heat treatment (HT) to evaluate the respective influences of electropulses and temperature on the recrystallization behavior of AZ31. The highest measured temperature during the EPT (543 K) was used in HT. The electron backscattered diffraction results demonstrated that the EPT-stimulated recrystallization was completed within 8 seconds, whereas for HT, recrystallization was still far from completion even after 240 seconds. It was found that both the nucleation and grain growth of these two processes were totally different. In the EPT samples, nucleation tended to occur preferentially near extension twin boundaries and grain boundaries by continuous recrystallization, whereas in the HT samples, nucleation occurred mainly by grain boundaries bulging via discontinuous recrystallization. As grain growth proceeded, the texture intensities of the EPT samples decreased gradually and finally evolved into an obvious transverse-direction-split texture. This is likely attributable to the impact of electropulses on the boundary energy and the contribution of nonbasal dislocations; however, the basal-type textures of the HT samples were notably strengthened, which is associated with a 30 deg〈0001〉 orientation with respect to the deformed texture.

Recrystallization and grain growth behavior of rolled tungsten under VDE-like short pulse high heat flux loads

International Nuclear Information System (INIS)

Yuan, Y.; Greuner, H.; Böswirth, B.; Krieger, K.; Luo, G.-N.; Xu, H.Y.; Fu, B.Q.; Li, M.; Liu, W.

2013-01-01

Highlights: ► Recrystallization temperature of a rolled W was ∼2480 °C under applied HHF loads. ► Fine grains were obtained under HHF loads with appropriate short pulse length. ► With increasing pulse length, the recrystallized grains significantly grew larger. ► A linear relationship between ln d and 1/T max was found. ► Activation energy for grain growth in T evolution up to T max in 1.5 s was obtained. -- Abstract: Short pulse heat loads expected for vertical displacement events (VDEs) in ITER were applied in the high heat flux (HHF) test facility GLADIS at IPP-Garching onto samples of rolled W. Pulsed neutral beams with the central heat flux of 23 MW/m 2 were applied for 0.5, 1.0 and 1.5 s, respectively. Rapid recrystallization of the adiabatically loaded 3 mm thick samples was observed when the pulse duration was up to 1.0 s. Grains grew markedly following recrystallization with increasing pulse length. The recrystallization temperature and temperature dependence of the recrystallized grain size were also investigated. The results showed that the recrystallization temperature of the W grade was around 2480 °C under the applied heat loading condition, which was nearly 1150 °C higher than the conventional recrystallization temperature, and the grains were much finer. A linear relationship between the logarithm of average grain size (ln d) and the inverse of maximum surface temperature (1/T max ) was found and accordingly the activation energy for grain growth in temperature evolution up to T max in 1.5 s of the short pulse HHF load was deduced to be 4.1 eV. This provided an effective clue to predict the structure evolution under short pulse HHF loads

Recrystallization and grain growth behavior of rolled tungsten under VDE-like short pulse high heat flux loads

Science.gov (United States)

Yuan, Y.; Greuner, H.; Böswirth, B.; Krieger, K.; Luo, G.-N.; Xu, H. Y.; Fu, B. Q.; Li, M.; Liu, W.

2013-02-01

Short pulse heat loads expected for vertical displacement events (VDEs) in ITER were applied in the high heat flux (HHF) test facility GLADIS at IPP-Garching onto samples of rolled W. Pulsed neutral beams with the central heat flux of 23 MW/m2 were applied for 0.5, 1.0 and 1.5 s, respectively. Rapid recrystallization of the adiabatically loaded 3 mm thick samples was observed when the pulse duration was up to 1.0 s. Grains grew markedly following recrystallization with increasing pulse length. The recrystallization temperature and temperature dependence of the recrystallized grain size were also investigated. The results showed that the recrystallization temperature of the W grade was around 2480 °C under the applied heat loading condition, which was nearly 1150 °C higher than the conventional recrystallization temperature, and the grains were much finer. A linear relationship between the logarithm of average grain size (ln d) and the inverse of maximum surface temperature (1/Tmax) was found and accordingly the activation energy for grain growth in temperature evolution up to Tmax in 1.5 s of the short pulse HHF load was deduced to be 4.1 eV. This provided an effective clue to predict the structure evolution under short pulse HHF loads.

Laser-induced surface recrystallization of polycrystalline PbI2 thick films for X-ray detector application

Science.gov (United States)

Sun, Hui; Zhao, Beijun; Zhu, Xinghua; Zhu, Shifu; Yang, Dingyu; Wangyang, Peihua; Gao, Xiuyin

2018-01-01

In this work, laser-induced surface recrystallization process was developed to improve the surface properties and device performance of the polycrystalline PbI2 thick films prepared by using close space vapor deposition method. A continuous polycrystalline PbI2 recrystallized layer with a better mechanical strength and reflectivity improved from 2% to 4%-6% was obtained by this recrystallization process for the films with mechanical pretreatment. Other polytypes is absent in the recrystallized layer with the 2H-polytype remaining before and after treatment and obtaining improved electrical and X-ray photoelectric response performance. The pretreatment such as mechanical cutting/polishing and hydrogenation is necessary to lower the non-wetting crystallization behavior during the recrystallization process due to the rough surface state and oxygen contamination.

Effects of clustered nucleation on recrystallization

DEFF Research Database (Denmark)

Storm, Søren; Juul Jensen, Dorte

2009-01-01

Computer simulations are used to study effects of an experimentally determined 3D distribution of nucleation sites on the recrystallization kinetics and on the evolution of the recrystallized microstructure as compared to simulations with random nucleation. It is found that although...... the experimentally observed clustering is not very strong, it changes the kinetics and the recrystallized microstructural morphology plus leads to a recrystallized grain size distribution, which is significantly broadened compared to that of random nucleation simulations. (C) 2009 Published by Elsevier Ltd...

Recrystallization of the ODS superalloy PM-1000

International Nuclear Information System (INIS)

Sandim, H.R.Z.; Hayama, A.O.F.; Raabe, D.

2006-01-01

The primary recrystallization of a -fiber textured coarse-grained oxide dispersion strengthened nickel-based superalloy (PM-1000) has been investigated by high-resolution electron backscatter diffraction. The annealing behavior of this alloy is quite complex. Even at high annealing temperatures (e.g. 1200 deg. C), recrystallization is only partial. The microstructure of this superalloy in the annealed state consists of a blurred subgrain structure, coarse grains with sizes of about 10-20 μm at the pre-existing grain boundaries and a significant fraction of small crystals in the interior of the recovered grains. These small grains are elongated and display anisotropic growth. In the present paper we present a detailed explanation for this peculiar microstructure. Particular focus is placed on the origin of the new grains in the recovered structure in a [1 0 0]-oriented grain

Recrystallization induced plasticity in austenite and ferrite

International Nuclear Information System (INIS)

Huang Mingxin; Pineau, André; Bouaziz, Olivier; Vu, Trong-Dai

2012-01-01

Highlights: ► Plasticity can be induced by recrystallization in austenite and ferrite. ► Strain rate is proportional to recrystallization kinetics. ► Overall atomic flux selects a preferential direction may be the origin. - Abstract: New experimental evidences are provided to demonstrate that plastic strain can be induced by recrystallization in austenite and ferrite under an applied stress much smaller than their yield stresses. Such Recrystallization Induced Plasticity (RIP) phenomenon occurs because the overall atomic flux during recrystallization follows a preferential direction imposed by the applied stress.

Simulations of Recrystallization in Metals

DEFF Research Database (Denmark)

Godiksen, Rasmus Brauner

2007-01-01

structures in the deformed metal due to local effects: Inhomogeneous boundary morphologies and dislocation-structure-dependent migration rates are observed. The effects that the dislocation structures have must be taken into account in order to create realistic recrystallization models, and through......The growth of new near-perfect grains during recrystallization of deformed metals is governed by the migration of the grain boundaries surrounding the new grains. The grain boundaries migrate through the deformed metal driven by the excess energy of the dislocation structures created during...... deformation. Recently, it has been found that recrystallization is far more inhomogeneous than previously thought. The purpose of this PhD-project is to study recrystallization by computer simulations with special focus on inhomogeneous growth. Two types of simulations have been employed: geometric...

Recrystallization and embrittlement of sintered tungsten

International Nuclear Information System (INIS)

Bega, N.D.; Babak, A.V.; Uskov, E.I.

1982-01-01

The recrystallization of sintered tungsten with a cellular structure of deformation is studied as related to its embrittlement. It is stated that in case of preliminary recrystallization the sintered tungsten crack resistance does not depend on the testing temperature. The tungsten crack resistance is shown to lower with an increase of the structure tendency to primary recrystallization [ru

Quantitative analysis of the epitaxial recrystallization effect induced by swift heavy ions in silicon carbide

International Nuclear Information System (INIS)

Benyagoub, A.

2015-01-01

This paper discusses recent results on the recrystallization effect induced by swift heavy ions (SHI) in pre-damaged silicon carbide. The recrystallization kinetics was followed by using increasing SHI fluences and by starting from different levels of initial damage within the SiC samples. The quantitative analysis of the data shows that the recrystallization rate depends drastically on the local amount of crystalline material: it is nil in fully amorphous regions and becomes more significant with increasing amount of crystalline material. For instance, in samples initially nearly half-disordered, the recrystallization rate per incident ion is found to be 3 orders of magnitude higher than what it is observed with the well-known IBIEC process using low energy ions. This high rate can therefore not be accounted for by the existing IBIEC models. Moreover, decreasing the electronic energy loss leads to a drastic reduction of the recrystallization rate. A comprehensive quantitative analysis of all the experimental results shows that the SHI induced high recrystallization rate can only be explained by a mechanism based on the melting of the amorphous zones through a thermal spike process followed by an epitaxial recrystallization initiated from the neighboring crystalline regions if the size of the latter exceeds a certain critical value. This quantitative analysis also reveals that recent molecular dynamics calculations supposed to reproduce this phenomenon are wrong since they overestimated the recrystallization rate by a factor ∼40.

Recovery and recrystallization of U3Si

International Nuclear Information System (INIS)

Caillibot, P.F.; Wyatt, B.S.

1969-10-01

The recovery and recrystallization temperatures of U 3 Si were determined for an alloy of uranium-3.98 wt% silicon containing 600 ppm carbon. Small specimens, deformed by compression, were isothermally and isochronally annealed at temperatures between 350 and 700 o C and their recovery and recrystallization temperatures determined using hardness, grain size and X-ray measurements. For small amounts of strain and an annealing time of 6 hours both recovery and recrystallization begin at 400-450 o C. Complete recrystallization is achieved at 650-700 o C. The effect of small changes in silicon and carbon concentration were determined by examining two further alloys containing 3.27 wt% silicon and 600 ppm carbon, and 4.02 wt% silicon and 140 ppm carbon respectively. A small change in silicon concentration does not affect recovery and recrystallization but decreasing the carbon concentration from 600 to 140 ppm decreases the recovery and recrystallization temperatures. (author)

A new method to predict the metadynamic recrystallization behavior in a typical nickel-based superalloy

International Nuclear Information System (INIS)

Lin, Y.C.; Chen, Xiao-Min; Chen, Ming-Song; Wen, Dong-Xu; Zhou, Ying; He, Dao-Guang

2016-01-01

The metadynamic recrystallization (MDRX) behaviors of a typical nickel-based superalloy are investigated by two-pass hot compression tests and four conventional stress-based conventional approaches (offset stress method, back-extrapolation stress method, peak stress method, and mean stress method). It is found that the conventional stress-based methods are not suitable to evaluate the MDRX softening fractions for the studied superalloy. Therefore, a new approach, 'maximum stress method', is proposed to evaluate the MDRX softening fraction. Based on the proposed method, the effects of deformation temperature, strain rate, initial average grain size, and interpass time on MDRX behaviors are discussed in detail. Results show that MDRX softening fraction is sensitive to deformation parameters. The MDRX softening fraction rapidly increases with the increase of deformation temperature, strain rate, and interpass time. The MDRX softening fraction in the coarse-grain material is lower than that in the fine-grain material. Moreover, the observed microstructures indicate that the initial coarse grains can be effectively refined by MDRX. Based on the experimental results, the kinetics equations are established and validated to describe the MDRX behaviors of the studied superalloy. (orig.)

Mechanical behavior and high-resolution EBSD investigation of the microstructural evolution in AISI 321 stainless steel under dynamic loading condition

International Nuclear Information System (INIS)

Tiamiyu, A.A.; Eskandari, M.; Sanayei, Mohsen; Odeshi, A.G.; Szpunar, J.A.

2016-01-01

The impact response of three regions (top, mid and center) across the thickness of AISI 321 austenitic stainless steel plate at high strain rates (>6000 s −1 ) was studied using the split Hopkinson pressure bar system. The result shows that texture and stored energy heterogeneity across plate thickness influenced the mechanical responses of the investigated steel in these regions. Microstructural evaluation using high-resolution electron backscattered diffraction (HR-EBSD) analysis showed that strengthening in AISI 321 steel originates from the evolution of strain-induced martensite and formation of nano-carbides in addition to plastic deformation by mechanical twinning and slip. This resulted in a desirable combination of high strength and good ductility (approx. 2000 MPa at 0.42 true strain). Phase transformation, dynamic recrystallization and formation of nano-carbides were confirmed within the adiabatic shear band (ASB) region. The average dynamic recrystallized (DRX) grain size in the shear band region is 0.28 µm in comparison to grain size of 15 µm outside the shear bands. The nano-sized grain inside the shear bands is proposed to form by rotational dynamic recrystallization. A comparative study of the alloy's behavior under dynamic and quasi-static compression shows that the stability of austenite is higher at high strain rates and lower at a low strain rate. The strength in the dynamically impacted specimen is compromised as a result of the suppressed evolution of strain-induced martensite and mechanical twin. Martensitic transformation under both loading conditions follows the FCC É£-austenite→BCC ά-martensite kinetic path and both phases obey the Kurdjumov-Sachs' {(111)É£||(110)ά and <−101>É£||<1–11>ά} orientation relationship.

Mechanical behavior and high-resolution EBSD investigation of the microstructural evolution in AISI 321 stainless steel under dynamic loading condition

Energy Technology Data Exchange (ETDEWEB)

Tiamiyu, A.A., E-mail: ahmed.tiamiyu@usask.ca [Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Sask. (Canada); Eskandari, M. [Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz (Iran, Islamic Republic of); Sanayei, Mohsen; Odeshi, A.G.; Szpunar, J.A. [Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Sask. (Canada)

2016-09-15

The impact response of three regions (top, mid and center) across the thickness of AISI 321 austenitic stainless steel plate at high strain rates (>6000 s{sup −1}) was studied using the split Hopkinson pressure bar system. The result shows that texture and stored energy heterogeneity across plate thickness influenced the mechanical responses of the investigated steel in these regions. Microstructural evaluation using high-resolution electron backscattered diffraction (HR-EBSD) analysis showed that strengthening in AISI 321 steel originates from the evolution of strain-induced martensite and formation of nano-carbides in addition to plastic deformation by mechanical twinning and slip. This resulted in a desirable combination of high strength and good ductility (approx. 2000 MPa at 0.42 true strain). Phase transformation, dynamic recrystallization and formation of nano-carbides were confirmed within the adiabatic shear band (ASB) region. The average dynamic recrystallized (DRX) grain size in the shear band region is 0.28 µm in comparison to grain size of 15 µm outside the shear bands. The nano-sized grain inside the shear bands is proposed to form by rotational dynamic recrystallization. A comparative study of the alloy's behavior under dynamic and quasi-static compression shows that the stability of austenite is higher at high strain rates and lower at a low strain rate. The strength in the dynamically impacted specimen is compromised as a result of the suppressed evolution of strain-induced martensite and mechanical twin. Martensitic transformation under both loading conditions follows the FCC É£-austenite→BCC ά-martensite kinetic path and both phases obey the Kurdjumov-Sachs' {(111)É£||(110)ά and <−101>É£||<1–11>ά} orientation relationship.

Nucleation of recrystallization in fine-grained materials: an extension of the Bailey-Hirsch criterion

Science.gov (United States)

Favre, Julien; Fabrègue, Damien; Chiba, Akihiko; Bréchet, Yves

2013-11-01

A new criterion for nucleation in the case of dynamic recrystallization is proposed in order to include the contribution of the grain boundary energy stored in the microstructure in the energy balance. Due to the nucleation events, the total surface area of pre-existing grain boundaries decreases, leading to a nucleus size smaller than expected by conventional nucleation criteria. The new model provides a better prediction of the nucleus size during recrystallization of pure copper compared with the conventional nucleation criterion.

Recrystallization behavior, microstructure evolution and mechanical properties of biodegradable Fe–Mn–C(–Pd) TWIP alloys

International Nuclear Information System (INIS)

Schinhammer, Michael; Pecnik, Christina M.; Rechberger, Felix; Hänzi, Anja C.; Löffler, Jörg F.; Uggowitzer, Peter J.

2012-01-01

In this study the interplay between recrystallization and precipitation in a biodegradable TWIP (twinning-induced plasticity) steel developed for use in temporary implants was investigated. Microstructural and mechanical properties were studied and a thermomechanical treatment was designed with the aim of achieving an overall performance suitable for the intended application as temporary implant material. The formation of Pd-rich precipitates in the cold-worked state was found to considerably retard recrystallization during an annealing treatment. The formation, morphology and interaction with dislocations of these precipitates were studied by means of scanning and transmission electron microscopy. Grain boundary pinning by Pd-rich precipitates (Zener drag) and reduced dislocation mobility due to a solute drag effect caused by the enrichment of dislocation cores with Pd were both identified as mechanisms which impede recrystallization. A model is reported which explains the interplay between recrystallization and precipitation, and provides the basis for the optimized thermomechanical treatment then presented. The resulting mechanical properties, in particular the combination of high strength and ductility with a pronounced strain-hardening response, exceed the performance of other TWIP steels and alloys typically used in biomedical implants, such as stainless steel, titanium or cobalt–chromium alloys. The specific property profile developed is especially advantageous for the production and deployment of cardiovascular stents.

Modeling Microstructural Evolution During Dynamic Recrystallization of Alloy D9 Using Artificial Neural Network

Science.gov (United States)

Mandal, Sumantra; Sivaprasad, P. V.; Dube, R. K.

2007-12-01

An artificial neural network (ANN) model was developed to predict the microstructural evolution of a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (Alloy D9) during dynamic recrystallization (DRX). The input parameters were strain, strain rate, and temperature whereas microstructural features namely, %DRX and average grain size were the output parameters. The ANN was trained with the database obtained from various industrial scale metal-forming operations like forge hammer, hydraulic press, and rolling carried out in the temperature range 1173-1473 K to various strain levels. The performance of the model was evaluated using a wide variety of statistical indices and the predictability of the model was found to be good. The combined influence of temperature and strain on microstructural features has been simulated employing the developed model. The results were found to be consistent with the relevant fundamental metallurgical phenomena.

Recovery and recrystallization of U{sub 3}Si

Energy Technology Data Exchange (ETDEWEB)

Caillibot, P F; Wyatt, B S

1969-10-15

The recovery and recrystallization temperatures of U{sub 3}Si were determined for an alloy of uranium-3.98 wt% silicon containing 600 ppm carbon. Small specimens, deformed by compression, were isothermally and isochronally annealed at temperatures between 350 and 700{sup o}C and their recovery and recrystallization temperatures determined using hardness, grain size and X-ray measurements. For small amounts of strain and an annealing time of 6 hours both recovery and recrystallization begin at 400-450{sup o}C. Complete recrystallization is achieved at 650-700{sup o}C. The effect of small changes in silicon and carbon concentration were determined by examining two further alloys containing 3.27 wt% silicon and 600 ppm carbon, and 4.02 wt% silicon and 140 ppm carbon respectively. A small change in silicon concentration does not affect recovery and recrystallization but decreasing the carbon concentration from 600 to 140 ppm decreases the recovery and recrystallization temperatures. (author)

Advanced characterization of microstructural changes during recrystallization in aluminum alloy 6013

International Nuclear Information System (INIS)

Bieda, M; Kawalko, J; Sztwiertnia, K; Brisset, F

2015-01-01

Aluminum alloy 6013 was chosen as an example of a material that, after thermal treatment, possesses a relatively uniform and stable bimodal distribution of fine (<<1 μm) and coarse (>1 μm) particles. Samples of this alloy were subjected to plastic deformation by cold rolling. The presence of large and small particles has an influence on the behavior of this material during the recrystallization process. A complex investigation of the microstructural changes during annealing were carried out by means of advanced SEM and TEM techniques. Orientation mapping (OM), i.e., automatic determination of the topography of the crystallographic orientations, was performed using electron backscatter diffraction (EBSD) in the SEM and microdiffraction in the TEM experiments. These techniques were combined with in-situ heating experiments in the TEM and SEM experiments. The quantitative description of the microstructure at each step of recrystallization is presented. Changes in the microstructure of the investigated material during annealing reveal the role and impact of both types of particles on recrystallization and grain growth. The obtained results are in agreement with parallel calorimetric studies. (paper)

Additional grain refinement in recrystallization controlled rolling of Ti-microalloyed steels processed by near-net-shape casting technology

International Nuclear Information System (INIS)

Arribas, M.; Lopez, B.; Rodriguez-Ibabe, J.M.

2008-01-01

This paper analyzes the recrystallization kinetics in Ti-microalloyed steels processed using 'beam blank' casting technology. The faster solidification rates associated with this technology brings a finer precipitation of TiN particles which are very effective in controlling austenite grain growth during hot working. Furthermore, these small precipitates have been shown to delay static and dynamic recrystallization. The finer the precipitates the higher the delay in recrystallization. Nevertheless, beyond particle size and distribution, the level of delay is very dependent on microstructure (above all austenite grain size) and deformation conditions (strain and temperature). This paper studies the effects of this recrystallization delay on the microstructure evolution during hot rolling. Special attention was paid to the study of the occurrence of partial recrystallization during the final stages of rolling, which could lead to the presence of mixed microstructures before transformation. The possibility of achieving an additional austenite grain size refinement prior to transformation was evaluated

EBSD Analysis of Deformed and Partially Recrystallized Microstructures in ECAE-Processed Copper

DEFF Research Database (Denmark)

Mishin, Oleg; Bowen, Jacob R.; Godfrey, A.

2012-01-01

The deformed microstructure and recrystallization behavior of copper samples processed using equal channel angular extrusion (ECAE) have been investigated. The heavily deformed microstructure was found to be non-uniform through the sample thickness and to vary in a manner consistent with the non...

Deformation Mechanism and Recrystallization Relationships in Galfenol Single Crystals: On the Origin of Goss and Cube Orientations

Science.gov (United States)

Na, Suok-Min; Smith, Malcolm; Flatau, Alison B.

2018-06-01

In this work, deformation mechanism related to recrystallization behavior in single-crystal disks of Galfenol (Fe-Ga alloy) was investigated to gain insights into the influence of crystal orientations on structural changes and selective grain growth that take place during secondary recrystallization. We started with the three kinds of single-crystal samples with (011)[100], (001)[100], and (001)[110] orientations, which were rolled and annealed to promote the formation of different grain structures and texture evolutions. The initial Goss-oriented (011)[100] crystal mostly rotated into {111} orientations with twofold symmetry and shear band structures by twinning resulted in the exposure of rolled surface along {001} orientation during rolling. In contrast, the Cube-oriented (001)[100] single crystal had no change in texture during rolling with the thickness reduction up to 50 pct. The {123} slip systems were preferentially activated in these single crystals during deformation as well as {112} slip systems that are known to play a role in primary slip of body-centered cubic (BCC) materials such as α-iron and Fe-Si alloys. After annealing, the deformed Cube-oriented single crystal had a small fraction ( orientation, associated with {123} slip systems as well. This was expected to provide potential sites of nucleation for secondary recrystallization; however, no Goss- and Cube-oriented components actually developed in this sample during secondary recrystallization. Those results illustrated how the recrystallization behavior can be influenced by deformed structure and the slip systems.

Regularities of recrystallization in rolled Zr single crystals

International Nuclear Information System (INIS)

Isaenkova, M; Perlovich, Yu; Fesenko, V; Krymskaya, O; Krapivka, N; Thu, S S

2015-01-01

Experiments by rolled single crystals give a more visible conception of the operating mechanisms of plastic deformation and the following recrystallization, than experiments by polycrystals. Studies by usage of X-ray diffraction methods were conducted by Zr single crystals. It was revealed, that regions of the α-Zr matrix, deformed mainly by twinning, are characterized with decreased tendency to recrystallization. Orientations of recrystallized α-Zr grains correspond to “slopes” of maxima in the rolling texture, where the level of crystalline lattice distortion is maximal and the number of recrystallization nuclei is most of all. (paper)

Formation of recrystallization textures after hot working of AA2014 and AA6063

Energy Technology Data Exchange (ETDEWEB)

Geertruyden, W.H. van; Misiolek, W.Z. [Inst. for Metal Forming, Lehigh Univ., Bethlehem, PA (United States); Goncalves, M.; Szilagyi, G. [IPT-Dimet, Cidade Universitara, Sao Paulo-SP (Brazil); Nowell, M. [TSL/EDAX, Draper, UT (United States)

2002-07-01

This paper involves the investigation of the material response of two commercial aluminum alloys, 2014 and 6063, to thermo-mechanical processing parameters and the subsequent effects on the recrystallization behavior. Samples of the 2014 and 6063 alloys were hot rolled at 350, 400, 480, and 500 C to reductions of 50% and 75%. The samples were subsequently solutionized at 500 C (2014) and 525 C (6063) for 1 hour. Light optical microscopy (LOM) was performed which showed increased recrystallization kinetics in the 6063 alloy relative to the 2014 alloy. The solutionized samples of the 2014 alloy showed a banded microstructure indicating recrystallization was inhibited in the normal direction. The microtexture of the samples was characterized using electron backscatter diffraction (EBSD). Orientation distribution functions (ODF) and pole figures showed that the 6063 alloy displayed a copper rolling texture {l_brace}112{r_brace} left angle 111 right angle and an increasing cube recrystallization texture {l_brace}001{r_brace} left angle 100 right angle as the deformation temperature was increased. At low deformation temperatures, the 2014 alloy had a mixed Goss {l_brace}110{r_brace} left angle 001 right angle and Brass {l_brace}011{r_brace} left angle 211 right angle texture, while at higher temperatures and reductions the Brass component was very strong. The 2014 recrystallized texture was predominantly a cube texture rotated 45 degrees about the normal direction. (orig.)

Recrystallization - Fundamental aspects and relations to deformation microstructure

International Nuclear Information System (INIS)

Hansen, N.; Huang, X.; Juul Jensen, D.; Lauridsen, E.M.; Leffers, T.; Pantleon, W.; Sabin, T.J.; Wert, J.A.

2000-01-01

This Symposium, and hence this proceedings volume, is concerned with the mechanisms that control recrystallization of deformed metals and alloys. Central themes are the fundamental microstructural, orientational, and kinetic aspects of the recrystallization process; especially as they relate to the nature of the deformed state, to nucleation and growth of recrystallizing grains, and to models based on experimental observations. In recent years, significant progress has been made using a plethora of advanced techniques to characterize the morphology and local orientations in deformed metals and alloys. Thus, a key topic of the Symposium is enhanced insight into the characteristics of the deformation substructure, and into modification of the substructure by recovery, which is essential for understanding fundamental recrystallization mechanisms. Microstructures in highly strained materials will be a topic of special interest. Elucidation of the deformation substructure, and thus the local distribution of stored energy, sets the stage for progress in understanding nucleation of recrystallizing grains. It also provides a basis for new insights into the growth of nuclei, in particular concerning the means by which the deformation substructure is absorbed by and becomes incorporated into the recrystallization interface. Aspects of recrystallization of relevance to this symposium span the range from experimental and model exploration of fundamental mechanisms to methods that link scientific understanding to industrial practice. Models developed by considering the physical mechanisms elucidated by experimental studies will be addressed, as will models that enable industrial exploitation of the fundamental knowledge. Altogether, one of the significant aims of the symposium is to enhance the exploitation of the expanding knowledge of fundamental recrystallization mechanisms in industrial practice (au)

Orientation aspects of growth during recrystallization

International Nuclear Information System (INIS)

Juul Jensen, D.

1997-04-01

Recrystallization of heavily cold rolled aluminium and copper is studied with the aim of achieving information about effects of crystallography orientation on the growth process. The potentials of several experimental techniques are analysed, and a method well suited for characterizing growth rates of grains with different orientations is developed. This method, which is referred to as the extended Cahn-Hagel method, is used for growth rate determinations in aluminium and copper deformed and annealed under five different conditions. In all the investigated cases, preferential growth of cube oriented grains is observed. Recrystallization models, which simulates the orientational as well as microstructural development, are described. selected models are applied for studies of recrystallization in aluminium and copper under specific deformation and annealing conditions as well as for more general studies of the effects of orientation dependent growth rates on the recrystallization microstructure and texture. Finally, reasons for the observed orientation dependent growth rates are discussed. A new mechanism, orientation pinning, is suggested and it is shown that this mechanism is necessary for the understanding of experimental results. (au) 4 tabs., 41 ills., 153 refs

Orientation aspects of growth during recrystallization

Energy Technology Data Exchange (ETDEWEB)

Juul Jensen, D.

1997-04-01

Recrystallization of heavily cold rolled aluminium and copper is studied with the aim of achieving information about effects of crystallography orientation on the growth process. The potentials of several experimental techniques are analysed, and a method well suited for characterizing growth rates of grains with different orientations is developed. This method, which is referred to as the extended Cahn-Hagel method, is used for growth rate determinations in aluminium and copper deformed and annealed under five different conditions. In all the investigated cases, preferential growth of cube oriented grains is observed. Recrystallization models, which simulates the orientational as well as microstructural development, are described. selected models are applied for studies of recrystallization in aluminium and copper under specific deformation and annealing conditions as well as for more general studies of the effects of orientation dependent growth rates on the recrystallization microstructure and texture. Finally, reasons for the observed orientation dependent growth rates are discussed. A new mechanism, orientation pinning, is suggested and it is shown that this mechanism is necessary for the understanding of experimental results. (au) 4 tabs., 41 ills., 153 refs.

Recrystallization of magnesium deformed at low temperatures

International Nuclear Information System (INIS)

Fromageau, R.; Pastol, J.L.; Revel, G.

1978-01-01

The recrystallization of magnesium was studied after rolling at temperatures ranging between 248 and 373 K. For zone refined magnesium the annealing behaviour as observed by electrical resistivity measurements showed two stages at about 250 K and 400 K due respectively to recrystallization and grain growth. The activation energy associated with the recrystallization stage was 0.75 +- 0.01 eV. In less pure magnesium, with nominal purity 99.99 and 99.9%, the recrystallization stage was decomposed into two substages. Activation energies were determined in relation with deformation temperature and purity. The magnesium of intermediate purity (99.99%) behaved similarly to the lowest purity metal when it was deformed at high temperature and to the purest magnesium when the deformation was made at low temperature. This behaviour was discussed in connection with the theories of Luecke and Cahn. (Auth.)

Devitrification and recrystallization of nanoparticle-containing glycerol and PEG-600 solutions.

Science.gov (United States)

Lv, Fukou; Liu, Baolin; Li, Weijie; Jaganathan, Ganesh K

2014-02-01

Nanoparticles in solution offer unique electrical, mechanical and thermal properties due to their physical presence and interaction with the state of dispersion. This work is aimed to study the effects of hydroxyapatite (HA) nanoparticles on the devitrification and recrystallization events of two important cryoprotective solutions used in cell and tissue preservation namely glycerol (60%w/w) and PEG-600 (50%w/w). HA nanoparticles (20, 40 or 60 nm) were incorporated into solutions at the content of 0.1% or 0.5%(w/w), and were studied by differential scanning calorimeter (DSC) and cryomicroscopy. The presence of nanoparticles does not change the glass transition temperatures and melting temperatures of quenched solutions, but significantly affects the behavior of devitrification and recrystallization upon warming. Cryomicroscopic investigation showed the complex interactions among solution type, nanoparticle size and nanoparticle content, which apparently influence ice crystal growth or recrystallization in the quenched dispersions. These findings have significant implications for biomaterial cryopreservation, cryosurgery, and food manufacturing. The complexity of ice crystal growth kinetics in nanoparticle-containing dispersions remains to be poorly understood at the moment. Copyright © 2013 Elsevier Inc. All rights reserved.

Study on the behavior of medium carbon vanadium microalloyed steel by hot compression test

International Nuclear Information System (INIS)

Meysami, Majid; Mousavi, Seyed Ali Asghar Akbari

2011-01-01

Research highlights: → At low Z parameter, the multi peak dynamic recrystallization behavior was observed. → At high Z, the stress-strain curves were exhibited with a single peak stress. → The hyperbolic sine law was found to provide the best fit for calculation of Q. → The average value of n was obtained as 4.687. → The peak stress and of the studied material was obtained. - Abstract: This article investigates the hot working behavior of medium carbon vanadium microalloyed steel by hot compression tests over the temperature range of 850-1100 deg. C and strain rate range of 0.001-0.5 s -1 to strain of 0.8. In this study, the general constitutive equations were used to determine the hot working constants. The peak stress (σ P ) and strain (ε P ) for initiation of dynamic recrystallization (DRX) at different temperatures and strain rates were calculated. The power law, exponential and hyperbolic sinusoidal types of Zener-Hollomon equations were used to determine the hot deformation activation energy (Q). The results suggested that the highest correlation coefficient was achieved for the hyperbolic sine law for the studied material. The magnitude of hot deformation activation energy (Q) was obtained as 319.910 kJ/mol. The classical single peak DRX was observed in most of temperatures and strain rates. However, for temperature of 1100 deg. C and strain rates of 0.001 s -1 , 0.01 s -1 , and also for temperature of 950 deg. C and strain rate of 0.001 s -1 the multiple peak dynamic recrystallization (MDRX) was observed, which showed that the 'recrystallization' was an observed strain rate behavior.

Bioinspired Materials for Controlling Ice Nucleation, Growth, and Recrystallization.

Science.gov (United States)

He, Zhiyuan; Liu, Kai; Wang, Jianjun

2018-05-15

Ice formation, mainly consisting of ice nucleation, ice growth, and ice recrystallization, is ubiquitous and crucial in wide-ranging fields from cryobiology to atmospheric physics. Despite active research for more than a century, the mechanism of ice formation is still far from satisfactory. Meanwhile, nature has unique ways of controlling ice formation and can provide resourceful avenues to unravel the mechanism of ice formation. For instance, antifreeze proteins (AFPs) protect living organisms from freezing damage via controlling ice formation, for example, tuning ice nucleation, shaping ice crystals, and inhibiting ice growth and recrystallization. In addition, AFP mimics can have applications in cryopreservation of cells, tissues, and organs, food storage, and anti-icing materials. Therefore, continuous efforts have been made to understand the mechanism of AFPs and design AFP inspired materials. In this Account, we first review our recent research progress in understanding the mechanism of AFPs in controlling ice formation. A Janus effect of AFPs on ice nucleation was discovered, which was achieved via selectively tethering the ice-binding face (IBF) or the non-ice-binding face (NIBF) of AFPs to solid surfaces and investigating specifically the effect of the other face on ice nucleation. Through molecular dynamics (MD) simulation analysis, we observed ordered hexagonal ice-like water structure atop the IBF and disordered water structure atop the NIBF. Therefore, we conclude that the interfacial water plays a critical role in controlling ice formation. Next, we discuss the design and fabrication of AFP mimics with capabilities in tuning ice nucleation and controlling ice shape and growth, as well as inhibiting ice recrystallization. For example, we tuned ice nucleation via modifying solid surfaces with supercharged unfolded polypeptides (SUPs) and polyelectrolyte brushes (PBs) with different counterions. We found graphene oxide (GO) and oxidized quasi

Preparation and recrystallization behavior of spray-dried co-amorphous naproxen-indomethacin

DEFF Research Database (Denmark)

Beyer, Andreas; Radi, Lydia; Grohganz, Holger

2016-01-01

(2) factorial design and the obtained samples were analyzed with X-ray powder diffractometry and Fourier-transformed infrared spectroscopy. Evaluation of the data revealed that the preparation of fully amorphous samples could be achieved depending on the process conditions. The resulting recrystallization......To improve the dissolution properties and the physical stability of amorphous active pharmaceutical ingredients, small molecule stabilizing agents may be added to prepare co-amorphous systems. The objective of the study was to investigate if spray-drying allows the preparation of co-amorphous drug...

In-situ observation of recrystallization in an AlMgScZr alloy using confocal laser scanning microscopy

International Nuclear Information System (INIS)

Taendl, J.; Nambu, S.; Orthacker, A.; Kothleitner, G.; Inoue, J.; Koseki, T.; Poletti, C.

2015-01-01

In this work we present a novel in-situ approach to study the recrystallization behavior of age hardening alloys. We use confocal laser scanning microscopy (CLSM) at 400 °C to investigate the static recrystallization of an AlMg4Sc0.4Zr0.12 alloy in-situ. The results are combined with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analyses. It was found that CLSM is a powerful tool to visualize both the local initiation and temporal sequence of recrystallization. After fast nucleation and initial growth, the grain growth rate decreases and the grain boundary migration stops after some minutes due to Zener pinning from Al 3 (Sc,Zr) precipitates produced during the heat treatment. EBSD and TEM analyses confirm both the boundary movements and the particle-boundary interactions. - Highlights: • First time that CLSM is used to study recrystallization in-situ. • The start and end of recrystallization can be directly observed. • The procedure is easy to apply and requires only simple data interpretation. • In-situ observations on the surface correlate to modifications inside the bulk. • In-situ observations correlate to EBSD and EFTEM analyses.

In-situ observation of recrystallization in an AlMgScZr alloy using confocal laser scanning microscopy

Energy Technology Data Exchange (ETDEWEB)

Taendl, J., E-mail: johannes.taendl@tugraz.atl [Institute of Materials Science and Welding, Graz University of Technology, Graz (Austria); Nambu, S. [Department of Materials Engineering, The University of Tokyo, Tokyo 113-8656 (Japan); Orthacker, A.; Kothleitner, G. [Institute of Electron Microscopy and Nanoanalysis, Graz University of Technology, Graz (Austria); Graz Center for Electron Microscopy, Graz (Austria); Inoue, J.; Koseki, T. [Department of Materials Engineering, The University of Tokyo, Tokyo 113-8656 (Japan); Poletti, C. [Institute of Materials Science and Welding, Graz University of Technology, Graz (Austria)

2015-10-15

In this work we present a novel in-situ approach to study the recrystallization behavior of age hardening alloys. We use confocal laser scanning microscopy (CLSM) at 400 °C to investigate the static recrystallization of an AlMg4Sc0.4Zr0.12 alloy in-situ. The results are combined with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analyses. It was found that CLSM is a powerful tool to visualize both the local initiation and temporal sequence of recrystallization. After fast nucleation and initial growth, the grain growth rate decreases and the grain boundary migration stops after some minutes due to Zener pinning from Al{sub 3}(Sc,Zr) precipitates produced during the heat treatment. EBSD and TEM analyses confirm both the boundary movements and the particle-boundary interactions. - Highlights: • First time that CLSM is used to study recrystallization in-situ. • The start and end of recrystallization can be directly observed. • The procedure is easy to apply and requires only simple data interpretation. • In-situ observations on the surface correlate to modifications inside the bulk. • In-situ observations correlate to EBSD and EFTEM analyses.

Deformation induced dynamic recrystallization and precipitation strengthening in an Mg−Zn−Mn alloy processed by high strain rate rolling

Energy Technology Data Exchange (ETDEWEB)

Jiang, Jimiao; Song, Min [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Yan, Hongge [School of Materials Science and Engineering, Hunan University, Changsha 410082 (China); Yang, Chao [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Ni, Song, E-mail: song.ni@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2016-11-15

The microstructure of a high strain-rate rolled Mg−Zn−Mn alloy was investigated by transmission electron microscopy to understand the relationship between the microstructure and mechanical properties. The results indicate that: (1) a bimodal microstructure consisting of the fine dynamic recrystallized grains and the largely deformed grains was formed; (2) a large number of dynamic precipitates including plate-like MgZn{sub 2} phase, spherical MgZn{sub 2} phase and spherical Mn particles distribute uniformly in the grains; (3) the major facets of many plate-like MgZn{sub 2} precipitates deviated several to tens of degrees (3°–30°) from the matrix basal plane. It has been shown that the high strength of the alloy is attributed to the formation of the bimodal microstructure, dynamic precipitation, and the interaction between the dislocations and the dynamic precipitates. - Highlights: •A bimodal microstructure was formed in a high strain-rate rolled Mg−Zn−Mn alloy. •Plate-like MgZn{sub 2}, spherical MgZn{sub 2} and spherical Mn phases were observed. •The major facet of the plate-like MgZn{sub 2} deviated from the matrix basal plane.

Analysis on dynamic tensile extrusion behavior of UFG OFHC Cu

Science.gov (United States)

Park, Kyung-Tae; Park, Leeju; Kim, Hak Jun; Kim, Seok Bong; Lee, Chong Soo

2014-08-01

Dynamic tensile extrusion (DTE) tests with the strain rate order of ~105 s-1 were conducted on coarse grained (CG) Cu and ultrafine grained (UFG) Cu. ECAP of 16 passes with route Bc was employed to fabricate UFG Cu. DTE tests were carried out by launching the sphere samples to the conical extrusion die at a speed of ~475 m/sec in a vacuumed gas gun system. UFG Cu was fragmented into 3 pieces and showed a DTE elongation of ~340%. CG Cu exhibited a larger DTE elongation of ~490% with fragmentation of 4 pieces. During DTE tests, dynamic recrystallization occurred in UFG Cu, but not in CG Cu. In order to examine the DTE behavior of CG Cu and UFG Cu under very high strain rates, a numerical analysis was undertaken by using a commercial finite element code (LS-DYNA 2D axis-symmetric model) with the Johnson - Cook model. The numerical analysis correctly predicted fragmentation and DTE elongation of CG Cu. But, the experimental DTE elongation of UFG Cu was much smaller than that predicted by the numerical analysis. This difference is discussed in terms of microstructural evolution of UFG Cu during DTE tests.

work hardening, recovery and recrystallization of alloys containing dispersed precipitates

International Nuclear Information System (INIS)

Padilha, A.F.

1989-01-01

This paper reviews the work hardening, recovery and recrystallization mechanisms in alloys containing dispersed precipitates. In the section on work hardening, the influence od spacing, particle size and shape on the density and distribution of dislocations have been discussed. They represent a large part of the energy stored in the material following drformation, which in turn is driving force for recrystallization. Next, the role of precipitates on recovery, on the formation and the growth of recrystallized regions has been discussed in detail. The competition between recovery and recrystallization and recrystallization of supersaturated solid solutions have also been mentioned. Finally, the technological relevance of the aspects treated in this paper has been discussed. (author) [pt

Effect of compression deformation on the microstructure and corrosion behavior of magnesium alloys

International Nuclear Information System (INIS)

Snir, Y.; Ben-Hamu, G.; Eliezer, D.; Abramov, E.

2012-01-01

Highlights: ► Metallurgical features (mainly twinning, dislocation accumulation, and dynamic recrystallization). ► The thermo-mechanical state (amount of deformation and its temperature). ► The corrosion behavior of wrought Mg-alloys. This correlation was emphasized by the mechanical behavior measured through micro-hardness. ► Microstructural changes during deformation, and potentio-dynamic corrosion tests were correlated. - Abstract: The effect of deformation on the corrosion and mechanical behavior of wrought Mg-alloys AZ31, AM50, and ZK60 was investigated. The materials’ behavior was correlated to the changes in metallurgical features, during compression, into different amounts of deformation at three temperatures: 250° C, 280° C, and 350° C. The metallurgical features were monitored by optical microscope, scanning electron microscope (SEM), and transmission electron microscopy (TEM). It was observed that there is a very strong correlation between three features: 1. metallurgical features (mainly twinning, dislocation accumulation, and dynamic recrystallization); 2. The thermo-mechanical state (amount of deformation and its temperature); and 3. The corrosion behavior of wrought Mg-alloys. This correlation was emphasized by the mechanical behavior measured through micro-hardness. Microstructural changes during deformation, and potentio-dynamic corrosion tests were correlated. These results show that studies on the effect of thermo-mechanical state (related to the microstructure) on the corrosion behavior of wrought Mg-alloys are essential in order to optimize their applicability to plastic forming processes.

Behavior of Goss, {411}<148>, and {111}<112> Oriented Grains During Recrystallization and Decarburization After Cold-rolling of Fe-3.1% GrainOriented Electrical Steel

Energy Technology Data Exchange (ETDEWEB)

Choi, Sung-Ji; Park, No-Jin [Kumoh National Institute of Technology, Gumi (Korea, Republic of); Joo, Hyung-Don; Park, Jong-Tae [POSCO, Pohang (Korea, Republic of)

2016-07-15

Grain-oriented electrical steel is used as a core material in transformers and motors. To obtain improved magnetic properties from the grain-oriented electrical steel, the steel should have a strong {110}<001> Goss texture. Recently, controlled manufacturing processes have been employed for developing electrical steels with a strong Goss texture. It is important to carry out research on the {411}<148> and {111}<112> oriented grains in relation to coincidence site lattice (CSL) boundaries, as they have an effect on the easy growth of the Goss grains upon secondary recrystallization. In this study, the behavior of the{411}<148> and {111}<112> oriented grains, which are neighbored with Goss grains after recrystallization with rapid and typical heating rates, and after decarburization, was examined by using x-ray diffraction (XRD) and electron back-scattered diffraction (EBSD) measurements. In the decarburized specimen, the Goss grains encroached the {411}<148> and {111}<112> oriented grains to a greater extent with a rapid heating rate than with a typical heating rate, and larger Goss grains were observed with the rapid heating rate. The {111}<112> oriented grains especially affect the easy growth of the Goss grains, as they are located near the Goss grains. Therefore, larger Goss grains can be produced at rapid heating rates, and the product is estimated to exhibit improved magnetic properties after secondary recrystallization.

Study on the behavior of medium carbon vanadium microalloyed steel by hot compression test

Energy Technology Data Exchange (ETDEWEB)

Meysami, Majid [School of Metallurgy and Materials Engineering, University College of Engineering, University of Tehran, P.O. Box 11155-4653, Tehran (Iran, Islamic Republic of); Mousavi, Seyed Ali Asghar Akbari, E-mail: akbarimusavi@ut.ac.ir [School of Metallurgy and Materials Engineering, University College of Engineering, University of Tehran, P.O. Box 11155-4653, Tehran (Iran, Islamic Republic of)

2011-03-25

Research highlights: {yields} At low Z parameter, the multi peak dynamic recrystallization behavior was observed. {yields} At high Z, the stress-strain curves were exhibited with a single peak stress. {yields} The hyperbolic sine law was found to provide the best fit for calculation of Q. {yields} The average value of n was obtained as 4.687. {yields} The peak stress and of the studied material was obtained. - Abstract: This article investigates the hot working behavior of medium carbon vanadium microalloyed steel by hot compression tests over the temperature range of 850-1100 deg. C and strain rate range of 0.001-0.5 s{sup -1} to strain of 0.8. In this study, the general constitutive equations were used to determine the hot working constants. The peak stress ({sigma}{sub P}) and strain ({epsilon}{sub P}) for initiation of dynamic recrystallization (DRX) at different temperatures and strain rates were calculated. The power law, exponential and hyperbolic sinusoidal types of Zener-Hollomon equations were used to determine the hot deformation activation energy (Q). The results suggested that the highest correlation coefficient was achieved for the hyperbolic sine law for the studied material. The magnitude of hot deformation activation energy (Q) was obtained as 319.910 kJ/mol. The classical single peak DRX was observed in most of temperatures and strain rates. However, for temperature of 1100 deg. C and strain rates of 0.001 s{sup -1}, 0.01 s{sup -1}, and also for temperature of 950 deg. C and strain rate of 0.001 s{sup -1} the multiple peak dynamic recrystallization (MDRX) was observed, which showed that the 'recrystallization' was an observed strain rate behavior.

Microstructural Analysis of Orientation-Dependent Recovery and Recrystallization in a Modified 9Cr-1Mo Steel Deformed by Compression at a High Strain Rate

DEFF Research Database (Denmark)

Zhang, Zhenbo; Zhang, Yubin; Mishin, Oleg

2016-01-01

energies in 〈111〉- and 〈100〉-oriented regions in deformed and annealed samples, as well as investigations of the growth of recrystallizing grains, are used to analyze the annealing behavior. It is concluded that recrystallization in the given material occurs by a combination of oriented nucleation...

Recrystallization curve study of zircaloy-4 with DRX line width method

International Nuclear Information System (INIS)

Juarez, G; Buioli, C; Samper, R; Vizcaino, P

2012-01-01

X-ray diffraction peak broadening analysis is a method that allows to characterize the plastic deformation in metals. This technique is a complement of transmission electron microscopy (TEM) to determine dislocation densities. So that, both techniques may cover a wide range in the analysis of metals deformation. The study of zirconium alloys is an issue of usual interest in the nuclear industry since such materials present the best combination of good mechanical properties, corrosion behavior and low neutron cross section. It is worth noting there are two factors to be taken into account in the application of the method developed for this purpose: the characteristic anisotropy of the hexagonals and the strong texture that these alloys acquire during the manufacturing process. In order to assess the recrystallization curve of Zircaloy-4, a powder of this alloy was produced through filing. Then, fractions of the powder were subjected to thermal treatments at different temperatures for the same time. Since the powder has a random crystallographic orientation, the texture effect practically disappears; this is the reason why the Williamson and Hall method may be easily used, producing good fittings and predicting confidence values of diffraction domain size and the accumulated deformation. The temperatures selected for the thermal treatments were 1000, 700, 600, 500, 420, 300 and 200 o C during 2 hs. As a result of these annealings, powders in different recovery stages were obtained (completely recrystallized, partially recrystallized and non-recrystallized structures with different levels of stress relieve). The obtained values were also compared with the non annealed powder ones. All the microstructural evolution through the annealings was followed by optical microscopy (author)

Mechanisms of deformation and of recrystallization of imperfect uranium monocrystals

International Nuclear Information System (INIS)

Calais, D.

1960-04-01

The various means by which plastic deformations by slip, twinning or kinking are produced by tension of imperfect α uranium single crystals prepared by a β → α phase change, have been studied by X-rays and micrographic examination. Depending on the crystallographic orientation with respect to the direction of the applied tension, and depending on the magnitude of the change in length, the crystals are deformed either preferentially according to a single mechanism, for example twinning, or simultaneously according to two or three mechanisms. The results of a subsequent annealing of the deformed single in the α phase are studied with respect to the deformation mechanisms. In the case of a deformation due primarily to (010) [100], (011) [100] or (110) [001] sliding, there occurs recrystallization by crystal growth selectivity. If the deformation occurs via deformation bands, there is recrystallization by 'oriented nucleation'. The crystals deformed preponderantly by twinning give on recrystallization perfect crystals having optimum dimensions and having orientational characteristics closely related to those of the original crystal. Finally are discussed some criteria relating to the geometry and the dynamics with a view to explaining the occurrence of such and such a deformation mechanism of a single crystal with a given orientation. This study, in conclusion, must help to define the best conditions (crystalline orientation and process of deformation) which will promote the growth of large, perfect, single crystals. (author) [fr

Rapid solidification and dynamic compaction of Ni-base superalloy powders

Science.gov (United States)

Field, R. D.; Hales, S. J.; Powers, W. O.; Fraser, H. L.

1984-01-01

A Ni-base superalloy containing 13Al-9Mo-2Ta (in at. percent) has been characterized in both the rapidly solidified condition and after dynamic compaction. Dynamically compacted specimens were examined in the as-compacted condition and observations related to current theories of interparticle bonding. In addition, the recrystallization behavior of the compacted material at relatively low temperature (about 0.5-0.75 Tm) was investigated.

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling

Directory of Open Access Journals (Sweden)

Tao Zhang

2018-01-01

Full Text Available Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX plays a vital role in grain refinement during hot deformation. Finite element models (FEM coupled with microstructure evolution models and cellular automata models (CA are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation.

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling

Science.gov (United States)

Zhang, Tao; Li, Lei; Lu, Shi-Hong; Gong, Hai; Wu, Yun-Xin

2018-01-01

Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX) plays a vital role in grain refinement during hot deformation. Finite element models (FEM) coupled with microstructure evolution models and cellular automata models (CA) are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation. PMID:29342080

Pioneering In Situ Recrystallization during Bead Milling: A Top-down Approach to Prepare Zeolite A Nanocrystals.

Science.gov (United States)

Anand, Chokkalingam; Yamaguchi, Yudai; Liu, Zhendong; Ibe, Sayoko; Elangovan, Shanmugam P; Ishii, Toshihiro; Ishikawa, Tsuyoshi; Endo, Akira; Okubo, Tatsuya; Wakihara, Toru

2016-07-05

Top-down approach has been viewed as an efficient and straightforward method to prepare nanosized zeolites. Yet, the mechanical breaking of zeolite causes amorphization, which usually requires a post-milling recrystallization to obtain fully crystalline nanoparticles. Herein we present a facile methodology to prepare zeolite nanocrystals, where milling and recrystallization can be performed in situ. A milling apparatus specially designed to work under conditions of high alkalinity and temperature enables the in situ recrystallization during milling. Taking zeolite A as an example, we demonstrate its size reduction from ~3 μm to 66 nm in 30 min, which is quite faster than previous methods reported. Three functions, viz., miniaturization, amorphization and recrystallization were found to take effect concurrently during this one-pot process. The dynamic balance between these three functions was achieved by adjusting the milling period and temperature, which lead to the tuning of zeolite A particle size. Particle size and crystallinity of the zeolite A nanocrystals were confirmed by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and water adsorption-desorption. This work presents a pioneering advancement in this field of nanosized zeolites, and will facilitate the mass production as well as boost the wide applications of nanosized zeolites.

High temperature deformation behavior and microstructural evolutions of a high Zr containing WE magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Asqardoust, Sh.; Zarei-Hanzaki, A. [School of Metallurgical & Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Fatemi, S.M., E-mail: mfatemi@ut.ac.ir [Shahid Rajaee Teacher Training University, Tehran (Iran, Islamic Republic of); Moradjoy-Hamedani, M. [School of Metallurgical & Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2016-06-05

Magnesium alloys containing RE elements (WE grade) are considered as potential materials for high temperature structural applications. To this end, it is crucial to study the flow behavior and the microstructural evolution of these alloys at high temperatures. In present work, the hot compression testing was employed to investigate the deformation behavior of a rolled WE54 magnesium alloy at elevated temperatures. The experimental material failed to deform to target strain of 0.6 at 250 and 300 °C, while the straining was successfully performed at 350 °C. A flow softening was observed at 350 °C, which was related to the depletion of RE strengthener elements, particularly Y atoms, from the solid solution and dynamic precipitation of β phases. It was suggested that the Zener pinning effect of the latter precipitates might retard the occurrence of dynamic recrystallization. As the temperature increased to 450 and 500 °C, the RE elements dissolved in the matrix and thus dynamic recrystallization could considerably progress in the microstructure. The comparative study of specimens cut along transverse ad normal direction (TD and ND specimens) implied that the presence of RE elements might effectively reduce the yield anisotropy in WE54 rolled alloy. Microstructural observations indicated a higher fraction of dynamically-recrystallized grains for the ND specimens. This was discussed relying on the different shares of deformation mechanism during compressing the TD and ND specimens. - Highlights: • Deformation behavior of a high Zr WE alloy was addressed at low strain rate. • Dynamic precipitation was realized at 350 °C. • The occurrence of DRX was retarded due to Zener pinning effect. • A higher DRX fraction was obtained in ND specimens comparing with TD ones.

Quantitative studies of the nucleation of recrystallization in metals utilizing microscopy and X-ray diffraction

DEFF Research Database (Denmark)

Larsen, Axel Wright

is proven to be a good way of determining microstructural parameters, which are important when studying recrystallization dynamics. The nucleation of recrystallizationat triple junctions has been studied by 3 dimensional X-ray diffraction (3DXRD), allowing for the first time the deformed and recrystallized......This thesis covers three main results obtained during the project: A reliable method of performing serial sectioning on metal samples utilizing a Logitech polishing machine has been developed. Serial sectioning has been performed on metal samples in 1 µmsteps utilizing mechanical polishing...... microstructures to be compared at a given nucleation site in the bulk of a metal sample. From an experiment threenuclei were identified, their respective crystal orientations were determined, and growth curves were obtained for two of them....

Modeling of the flow behavior of SAE 8620H combing microstructure evolution in hot forming

Science.gov (United States)

Fu, Xiaobin; Wang, Baoyu; Tang, Xuefeng

2017-10-01

With the development of net-shape forming technology, hot forming process is widely applied to manufacturing gear parts, during which, materials suffer severe plastic distortion and microstructure changes continually. In this paper, to understand and model the flow behavior and microstructure evolution, SAE 8620H, a widely used gear steel, is selected as the object and the flow behavior and microstructure evolution are observed by an isothermal hot compression tests at 1273-1373 K with a strain rate of 0.1-10 s-1. Depending on the results of the compression test, a set of internal-state-variable based unified constitutive equations is put forward to describe the flow behavior and microstructure evaluation of SAE 8620H. Moreover, the evaluation of the dislocation density and the fraction of dynamic recrystallization based on the theory of thermal activation is modeled and reincorporated into the constitutive law. The material parameters in the constitutive model are calculated based on the measured flow stress and dynamic recrystallization fraction. The predicted flow stress under different deformation conditions has a good agreement with the measured results.

Role of thermodynamic, kinetic and structural factors in the recrystallization behavior of amorphous erythromycin salts

Energy Technology Data Exchange (ETDEWEB)

Nanakwani, Kapil; Modi, Sameer R.; Kumar, Lokesh; Bansal, Arvind K., E-mail: akbansal@niper.ac.in

2014-04-01

Graphical abstract: - Highlights: • Crystallization kinetics of amorphous erythromycin salts was assessed. • Contribution of thermodynamic, kinetic and structural factors was evaluated. • Role of counterions on physical stability of amorphous salts was investigated. • Implications of the study: In rationalizing stabilization approach for amorphous form. - Abstract: Amorphous form has become an important drug delivery strategy for poorly water soluble drugs. However, amorphous form has inherent physical instability due to its tendency to recrystallize to stable crystalline form. In the present study, amorphous forms of erythromycin free base (ED) and its salts namely, stearate (ES), phosphate (EP) and thiocyanate (ET) were generated by in situ melt quenching and evaluated for their crystallization tendency. Salts were characterized for kinetic, thermodynamic and structural factors to understand crystallization behavior. Kinetics of crystallization followed the order as ES > EP > ET > ED. Fragility and molecular mobility does not completely explain these findings. However, configurational entropy (S{sub conf}), indicative of entropic barrier to crystallization, followed the order as ET > EP > ES > ED. Lower crystallization tendency of ED can be explained by its lower thermodynamic driving force for crystallization (H{sub conf}). This correlated well with different structural parameters for the counter ions.

Induced Recrystallization of CdTe Thin Films Deposited by Close-Spaced Sublimation

International Nuclear Information System (INIS)

Mayo, B.

1998-01-01

We have deposited CdTe thin films by close-spaced sublimation at two different temperature ranges. The films deposited at the lower temperature partially recrystallized after CdCl2 treatment at 350C and completely recrystallized after the same treatment at 400C. The films deposited at higher temperature did not recrystallize at these two temperatures. These results confirmed that the mechanisms responsible for changes in physical properties of CdTe films treated with CdCl2 are recrystallization and grain growth, and provided an alternative method to deposit CSS films using lower temperatures

Precipitation formation in recrystallized nickel-plated non-sag tungsten wire

International Nuclear Information System (INIS)

Lai, Z.H.

1994-01-01

It is well established that some metals, such as palladium and nickel, can easily penetrate into tungsten by fast diffusion via crystal defects such as grain boundaries and dislocations. As a result of the fast penetration of these so called activators the recrystallization temperature of heavily drawn non-sag tungsten wire can be lower from about 2,000 C to about 1,000 C, thus the application of the tungsten wire, serving as reinforcement material in metal matrix composites used at high temperatures, is limited. An interesting question is in which form these activators exist in the recrystallized tungsten wire. It is generally believed that W-Ni intermediate compounds could form in the recrystallized material, presumably at grain boundaries. The free energy difference between the pure tungsten fibbers and the precipitating W(Ni) solid solution was suggested as the chemical driving force which governed the recrystallization process. The presence of nickel in small particles had also been observed in recrystallized grains of nickel plated tungsten wires using scanning electron microscopy (SEM) and secondary ion mass spectroscopy. These particles were considered to be nickel rich precipitates. However, a detailed investigation of the precipitation process has not been reported. In the present work an investigation of the structure, composition and distribution of nickel rich particles precipitated in recrystallized grains of nickel plated heavily drawn non-sage tungsten wires was carried out using analytical electron microscopy (AEM)

Fission-induced recrystallization effect on intergranular bubble-driven swelling in U-Mo fuel

Energy Technology Data Exchange (ETDEWEB)

Liang, Linyun; Mei, Zhi-Gang; Yacout, Abdellatif M.

2017-10-01

We have developed a mesoscale phase-field model for studying the effect of recrystallization on the gas-bubble-driven swelling in irradiated U-Mo alloy fuel. The model can simulate the microstructural evolution of the intergranular gas bubbles on the grain boundaries as well as the recrystallization process. Our simulation results show that the intergranular gas-bubble-induced fuel swelling exhibits two stages: slow swelling kinetics before recrystallization and rapid swelling kinetics with recrystallization. We observe that the recrystallization can significantly expedite the formation and growth of gas bubbles at high fission densities. The reason is that the recrystallization process increases the nucleation probability of gas bubbles and reduces the diffusion time of fission gases from grain interior to grain boundaries by increasing the grain boundary area and decreasing the diffusion distance. The simulated gas bubble shape, size distribution, and density on the grain boundaries are consistent with experimental measurements. We investigate the effect of the recrystallization on the gas-bubble-driven fuel swelling in UMo through varying the initial grain size and grain aspect ratio. We conclude that the initial microstructure of fuel, such as grain size and grain aspect ratio, can be used to effectively control the recrystallization and therefore reduce the swelling in U-Mo fuel.

Effect of grain shape and texture on equi-biaxial creep of stress relieved and recrystallized Zircaloy-4

International Nuclear Information System (INIS)

Murty, K.L.; Tanikella, B.V.; Earthman, J.C.

1994-01-01

Zirconium alloys are extensively used in various types of fission reactors both light and heavy water types for different applications, examples being thin-walled tubing to clad radioactive fuel, grids, channels in boiling water reactors (BWRs) as well as pressure and calandria tubes in pressurized heavy water reactors (PHWRs). Biaxial creep behaviors of stress relieved and recrystallized thin-walled tubing of Zircaloy-4 are considered under equal hoop and axial stresses by internal pressurization superimposed with axial load. Both hoop and axial strains were monitored and the ratio of the strain rates along the hoop to axial directions is considered to represent the degree of anisotropy. The slightly stronger hoop direction of the recrystallized material became weaker compared to the axial direction following cold work and a stress-relief anneal. Crystallographic texture was considered in terms of x-ray pole figures from which the crystallite orientation distribution functions (CODF) were derived. A crystal plasticity model based on slip on representative systems was combined with the CODF to predict the creep anisotropy. It was found that the textural differences between the recrystallized and stress-relieved material is believed to invoke anisotropic grain boundary sliding leading to stress enhancement in the hoop direction. This stress enhancement is shown to account for the observed differences in creep behavior between the present equiaxed and columnar grain structures

Mechanism of secondary recrystallization of Goss grains in grain-oriented electrical steel

Science.gov (United States)

Hayakawa, Yasuyuki

2017-12-01

Since its invention by Goss in 1934, grain-oriented (GO) electrical steel has been widely used as a core material in transformers. GO exhibits a grain size of over several millimeters attained by secondary recrystallization during high-temperature final batch annealing. In addition to the unusually large grain size, the crystal direction in the rolling direction is aligned with , which is the easy magnetization axis of α-iron. Secondary recrystallization is the phenomenon in which a certain very small number of {110} (Goss) grains grow selectively (about one in 106 primary grains) at the expense of many other primary recrystallized grains. The question of why the Goss orientation is exclusively selected during secondary recrystallization has long been a main research subject in this field. The general criterion for secondary recrystallization is a small and uniform primary grain size, which is achieved through the inhibition of normal grain growth by fine precipitates called inhibitors. This paper describes several conceivable mechanisms of secondary recrystallization of Goss grains mainly based on the selective growth model.

Annealing Twinning and the Nucleation of Recrystallization at Grain Boundaries

DEFF Research Database (Denmark)

Jones, A R.

1981-01-01

boundaries during recovery might stimulate nucleation of recrystallization in low stacking fault energy materials. The experimental observations also lead to the implication that the density of recrystallization nuclei formed in such materials may be directly related to the strength of the deformation...

Application of titanium-in-quartz thermobarometry to greenschist facies veins and recrystallized quartzites in the Hsüehshan range, Taiwan

Directory of Open Access Journals (Sweden)

S. Kidder

2013-01-01

Full Text Available The accuracy, reliability and best practises of Ti-in-quartz thermobarometry (TitaniQ in greenschist facies rocks have not been established. To address these issues, we measured Ti concentrations in rutile-bearing samples of moderately deformed, partially recrystallized quartzite and vein quartz from the Hsüehshan range, Taiwan. The spread of Ti concentrations of recrystallized grains in quartzite correlates with recrystallized grain size. Recrystallized quartz (grain size ~100–200 μm that formed during early deformation within the biotite stability field shows a marked increase in intermediate Ti-concentration grains (~1–10 ppm relative to detrital porphyroclasts (Ti ~0.1–200 ppm. Fine recrystallized quartz (~5% of the samples by area, grain size ~10–20 μm has a further restricted Ti concentration peaking at 0.8–2 ppm. This trend suggests equilibration of Ti in recrystallized quartz with a matrix phase during deformation and cooling. Unlike previously documented examples, Ti concentration in the quartzite is inversely correlated with blue cathodoluminescence. Deformation was associated with a minimum grain boundary diffusivity of Ti on the order of 10−22m2 s−1. Vein emplacement and quartzite recrystallization are independently shown to have occurred at 250–350 °C and 300–410 °C, respectively, with lithostatic pressure of 3–4 kbar (assuming a geothermal gradient of 25° km−1, and with hydrostatic fluid pressure. Estimates of the accuracy of TitaniQ at these conditions depend on whether lithostatic or fluid pressure is used in the TitaniQ calibration. Using lithostatic pressure and these temperatures, the Thomas et al. (2010 calibration yields Ti concentrations within error of concentrations measured by SIMS. If fluid pressure is instead used, predicted temperatures are ~30–40 °C too low. TitaniQ has potential to yield accurate PT information for vein emplacement and dynamic recrystallization of quartz at

effect of prior recovery on the recrystallization of carbon steel

African Journals Online (AJOL)

user

1988-09-01

Sep 1, 1988 ... "discontinuous" to the characteristically sluggish "continuous" mechanism. Introduction. Usually, when a metallic material is sufficiently deformed and then subjected to a temperature of at least 0.3 of its melting point, it undergoes primary recrystallization. The recrystallization process is considered to take.

Quasi-static and dynamic forced shear deformation behaviors of Ti-5Mo-5V-8Cr-3Al alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhiming; Chen, Zhiyong, E-mail: czysh@netease.com; Zhan, Congkun; Kuang, Lianjun; Shao, Jianbo; Wang, Renke; Liu, Chuming

2017-04-13

The mechanical behavior and microstructure characteristics of Ti-5Mo-5V-8Cr-3Al alloy were investigated with hat-shaped samples compressed under quasi-static and dynamic loading. Compared with the quasi-static loading, a higher shear stress peak and a shear instability stage were observed during the dynamic shear response. The results showed that an adiabatic shear band consisting of ultrafine equiaxed grains was only developed in the dynamic specimen, while a wider shear region was formed in the quasi-static specimen. The microhardness measurements revealed that shear region in the quasi-static specimen and adiabatic shear band in the dynamic specimen exhibited higher hardness than that of adjacent regions due to the strain hardening and grain refining, respectively. A stable orientation, in which the crystallographic {110} planes and <111> directions were respectively parallel to the shear plane and shear direction, developed in both specimens. And the microtexture of the adiabatic shear band was more well-defined than that of the shear region in the quasi-static specimen. Rotational dynamic recrystallization mechanism was suggested to explain the formation of ultrafine equiaxed grains within the adiabatic shear band by thermodynamic and kinetic calculations.

Aluminum nitrate recrystallization and recovery from liquid extraction raffinates

International Nuclear Information System (INIS)

Griffith, W.L.; Compere, A.L.; Googin, J.M.; Huxtable, W.P.

1991-09-01

The solid sludges resulting form biodenitrification of discarded aluminum nitrate are the largest Y-12 Plant process solid waste. Aluminum nitrate feedstocks also represent a major plant materials cost. The chemical constraints on aluminum nitrate recycle were investigated to determine the feasibility of increasing recycle while maintaining acceptable aluminum nitrate purity. Reported phase behavior of analogous systems, together with bench research, indicated that it would be possible to raise the recycle rate from 35% to between 70 and 90% by successive concentration and recrystallization of the mother liquor. A full scale pilot test successfully confirmed the ability to obtain 70% recycle in existing process equipment

Texture evolution during the recrystallization of a warm-rolled low-carbon steel

International Nuclear Information System (INIS)

Sanchez-Araiza, M.; Godet, S.; Jacques, P.J.; Jonas, J.J.

2006-01-01

The texture changes taking place during the recrystallization of a warm-rolled low-carbon steel were examined using electron backscattered diffraction. The deformation textures of the warm-rolled material are similar in shape to those of cold-rolled materials, but are somewhat more intense. The recrystallization textures resemble the deformation textures but with a more extended α fibre that includes the {1 1 3} orientation; the γ fibre extends to the {5 5 4} orientation. These two orientations are related to the {1 1 2} deformed grains by near 26 deg, rotations about selected axes. Nevertheless, both orientations appear in the early stages of recrystallization, an observation that does not support the oriented growth theory. The {1 1 1} orientations are the first to recrystallize while the α fibre is present until the end of recrystallization. It is finally consumed by all types of grains as well as by subgrain coalescence. The similarities in the growth rates for the {1 1 1} and random orientations and the late disappearance of the α fibre suggest that recrystallization takes place according to the high stored energy oriented nucleation concept

Determination of initial stages of recrystallization in aluminium alloys by X-ray diffraction

International Nuclear Information System (INIS)

Loew, Marjorie

2000-01-01

Aluminium is a metal with a wide variety of application, such as beer cans, pans, door and window borders, and others more advanced, such as airplane structure, car engines, nuclear reactors components, rocket propulsion components and so on. Most of aluminium application is in alloy form. Such alloys must present suitable mechanical and chemical properties that are obtained, not entirely, by microstructure development. In this work, the beginning of recrystallization processes of AA1050 and AA3003 aluminium alloys were studied using X-ray diffraction techniques, transmission electron microscopy and hardness test. For such a sample, an initial heat treatment was done in order to homogenize the samples microstructure, followed by cold rolling and submitted again to a heat treatment in different temperatures in a hot furnace. After that samples were analyzed to verify the beginning of the recrystallization. Vickers hardness test revealed that the beginning of recrystallization is between 150 and 300 deg C for 1050 aluminium alloy and 200 and 300 deg C for 3003 aluminium alloy. X-ray diffraction using transmission chamber showed that the beginning of recrystallization is 240 and 260 deg C for AA1050 and AA3003, respectively. These temperatures were determined as the diffraction patterns recorded in the photographic plates changes when the recrystallization takes place. In this way, the deformed sample shows continuous concentric lines and the beginning of recrystallization is characterized by the occurrence of defined spots in this pattern. The Pole Figures goniometric method revealed that the beginning of recrystallization takes place between 250 and 300 deg C for both alloys. In the same way, orientation distribution functions showed the same temperature range for the recrystallization. However, the analysis by α and β fiber figures, the recrystallization temperatures are 240 and 260 deg C for AA1050 and AA3003, respectively. Finally, after the analysis of all

Effect of zirconium addition on the recrystallization behaviour of a ...

Indian Academy of Sciences (India)

Unknown

commercial Al–Cu–Mg alloy. Keywords. Al–Cu–Mg alloy; recrystallization; Al3Zr particles; Zr addition. 1. Introduction. It is well known that recrystallization behaviour of an alloy is altered by the presence of second phase particles. Coarse second phase particles (> 1 µm) stimulate recrysta- llization by a mechanism known as ...

Phase-field simulation study of the migration of recrystallization boundaries

DEFF Research Database (Denmark)

Moelans, Nele; Godfrey, Andy; Zhang, Yubin

2013-01-01

We present simulation results based on a phase-field model that describes the local migration of recrystallization boundaries into varying deformation energy fields. An important finding from the simulations is that the overall migration rate of the recrystallization front can be considerably...... amplitudes, however, the velocity scales with the maximum of the deformation energy density along the variation, resulting in a considerably larger velocity than that obtained from standard recrystallization models. The shape of the migrating grain boundary greatly depends on the local characteristics...... of the varying stored deformation energy field. For different deformation energy fields, the simulation results are in good qualitative agreement with experiments and add information which cannot be directly derived from experiments....

Hot Deformation Behavior of Hot-Extruded AA7175 Through Hot Torsion Tests.

Science.gov (United States)

Lee, Se-Yeon; Jung, Taek-Kyun; Son, Hyeon-Woo; Kim, Sang-Wook; Son, Kwang-Tae; Choi, Ho-Joon; Oh, Sang-Ho; Lee, Ji-Woon; Hyun, Soong-Keun

2018-03-01

The hot deformation behavior of hot-extruded AA7175 was investigated with flow curves and processing maps through hot torsion tests. The flow curves and the deformed microstructures revealed that dynamic recrystallization (DRX) occurred in the hot-extruded AA7175 during hot working. The failure strain was highest at medium temperature. This was mainly influenced by the dynamic precipitation of fine rod-shaped MgZn2. The processing map determined the optimal deformation condition for the alloy during hot working.

Evolution of recrystallization microstructure and texture during rapid annealing in strip-cast non-oriented electrical steels

Energy Technology Data Exchange (ETDEWEB)

Fang, Feng [The State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China); Xu, Yun-Bo, E-mail: yunbo_xu@126.com [The State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China); Zhang, Yuan-Xiang; Wang, Yang; Lu, Xiang [The State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China); Misra, R.D.K [Laboratory for Excellence in Advanced Steel Research, Center for Structural and Functional Materials Research and Innovation and Department of Metallurgical and Materials Engineering, University of Texas at El Paso, 500W, University Avenue, El Paso, TX 79968 (United States); Wang, Guo-Dong [The State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China)

2015-05-01

Non-oriented electrical steel as-cast strip was produced by twin roll strip casting process, and subsequently cold rolled and annealed at heating rates in the range of 3–450 °C/s with the aim to elucidate the effect of heating rate on the evolution of recrystallized microstructure and texture. The average grain size was rapidly increased when the heating rate was increased from 3 to 25 °C/s, and decreased when the heating rate was greater than 25 °C/s. The average grain size did not increase linearly with heating rate, which was related to different degree of nucleation and growth rate. The recrystallization texture exhibited pronounced improvement during rapid annealing. At high heating rate, the Goss and Cube had a higher probability of nucleation of shear bands with high stored energy, while the intensity of the γ-fiber texture was significantly reduced. The highest B{sub 50} value attained was 1.803 T at a heating rate of 300 °C/s. The study indicates that rapid heating has strong effect on the recrystallization behavior in non-oriented electrical steels, which facilitates optimization of microstructure and texture, especially in the coarse-grained structure. - Highlights: • The effects of heating rate on the microstructure and texture of non-oriented steel were investigated. • The average grain size did not change monotonically with heating rate. • Recrystallization texture exhibited pronounced improvement in the as-cast strip. • Superior magnetic properties were obtained in twin-rolled strip casting process.

Recrystallization kinetics of warm-rolled tungsten in the temperature range 1150-1350 °C

DEFF Research Database (Denmark)

Alfonso Lopez, Angel; Juul Jensen, Dorte; Luo, G.-N.

2014-01-01

Pure tungsten is a potential candidate material for the plasma-facing first wall and the divertor of fusion reactors. Both parts have to withstand high temperatures during service. This will alter the microstructure of the material by recovery, recrystallization and grain growth and will cause...... in the mechanical properties during annealing are quantified by Vickers hardness measurements. They are described concisely by classical kinetic models for recovery and recrystallization. The observed time spans for recrystallization and the obtained value for the activation energy of the recrystallization process...

A phase-field simulation study of irregular grain boundary migration during recrystallization

DEFF Research Database (Denmark)

Moelans, N.; Zhang, Yubin; Godfrey, A.

2015-01-01

We present simulation results based on a phase-field model that describes the migration of recrystallization boundaries into spatially varying deformation energy fields. Energy fields with 2-dimensional variations representing 2 sets of dislocation boundaries lying at equal, but opposite, angles......, highly asymmetrical protrusions and retrusions can develop on the migrating recrystallization front resulting in a migration velocity considerably larger than that expected from standard recrystallization models. It is also seen that, when the wavelength of the variations in a deformation microstructure...

Adiabatic shear behaviors in rolled and annealed pure titanium subjected to dynamic impact loading

Energy Technology Data Exchange (ETDEWEB)

Kuang, Lianjun; Chen, Zhiyong, E-mail: czysh@netease.com; Jiang, Yanghui; Wang, Zhiming; Wang, Renke; Liu, Chuming

2017-02-08

The hat-shaped samples cut from rolled and annealed titanium plates were prepared to explore the adiabatic shear behaviors subjected to high-strain-rate deformation operated via Split Hopkinson Pressure Bar. The dynamic shear response calculation reveals that dynamic deformation processes of both state samples can be divided in similar three stages but rolled sample shows a higher susceptibility of adiabatic shear localization compared with the annealed one. Optical microscopy and electronic backscatter diffraction technique (EBSD) were used to systematically analyze the microstructure and texture characteristics. The results show that adiabatic shear bands form in both state samples and rotational dynamic recrystallization (RDRX) occurs within shear area and results in the formation of ultrafine equiaxed grains. Furthermore, ultrafine equiaxed grains within adiabatic shear bands have the same texture feature that <11–20> direction and {10-10} plane parallel to macro local shear direction and shear plane respectively. In the deformation region around the shear band, {10–12} <–1011> tensile and {11–22} <11-2-3> compressive two types twins are observed in both state samples and {10–12} <–1011> tensile twins are more frequently observed in rolled sample. In the rolled sample, {10–12} <–1011> tensile twins are more likely to happen in the hat-brim side than the hat-body side due to the difference of stress state in two sides.

Study of the precipitation-recrystallization interaction in a vanadium micro alloyed steel with 0.35 % C

International Nuclear Information System (INIS)

Quispe, A.B.; Medina, S.F.; Cabrera, J.M.; Prado, J.M.

1998-01-01

A method is described which allows to study the interaction recrystallization-induced precipitation by the deformation of vanadium micro alloyed steel and 0.35% C. By means of torsion tests and applying the Back Extrapolation method, the recrystallized fraction at different temperatures has been determined. When the precipitation begins, the recrystallized fraction does not follow the Avrami's equation. This allows to know the instant when precipitation starts (P s ) and the instant when precipitation finishes (P f ). Therefore, Recrystallization-Precipitation-Time-Temperature (RPTT) diagrams can be obtained, which graphically show the interaction Recrystallization-Precipitation and simultaneously allows the determination of the static recrystallization critical temperature (SRCT). This temperature represents the limit between the two phases, before and after precipitation. (Author) 10 refs

Metadynamic recrystallization in C steels

Indian Academy of Sciences (India)

Metadynamic recrystallization has been investigated in three plain carbon steels (ENIA, EN2 and EN24) through the use of hot interrupted compression tests on a wedge plastometer. Holding time was 0.5 s between passes. Strain rates of 0.05 and 0.12/s and small strain increments of 3, 5 and 7% were employed.

Dissolution-recrystallization method for high efficiency perovskite solar cells

Energy Technology Data Exchange (ETDEWEB)

Han, Fei; Luo, Junsheng; Wan, Zhongquan; Liu, Xingzhao; Jia, Chunyang, E-mail: cyjia@uestc.edu.cn

2017-06-30

Highlights: • Dissolution-recrystallization method can improve perovskite crystallization. • Dissolution-recrystallization method can improve TiO{sub 2}/perovskite interface. • The optimal perovskite solar cell obtains the champion PCE of 16.76%. • The optimal devices are of high reproducibility. - Abstract: In this work, a dissolution-recrystallization method (DRM) with chlorobenzene and dimethylsulfoxide treating the perovskite films during the spin-coating process is reported. This is the first time that DRM is used to control perovskite crystallization and improve the device performance. Furthermore, the DRM is good for reducing defects and grain boundaries, improving perovskite crystallization and even improving TiO{sub 2}/perovskite interface. By optimizing, the DRM2-treated perovskite solar cell (PSC) obtains the best photoelectric conversion efficiency (PCE) of 16.76% under AM 1.5 G illumination (100 mW cm{sup −2}) with enhanced J{sub sc} and V{sub oc} compared to CB-treated PSC.

Boundary Fractal Analysis of Two Cube-oriented Grains in Partly Recrystallized Copper

DEFF Research Database (Denmark)

Sun, Jun; Zhang, Yubin; Dahl, Anders Bjorholm

2015-01-01

The protrusions and retrusions observed on the recrystallizing boundaries affect the migration kinetics during recrystallization. Characterization of the boundary roughness is necessary in order to evaluate their effects. This roughness has a structure that can be characterized by fractal analysis...

Determination of grain boundary mobility during recrystallization by statistical evaluation of electron backscatter diffraction measurements

International Nuclear Information System (INIS)

Basu, I.; Chen, M.; Loeck, M.; Al-Samman, T.; Molodov, D.A.

2016-01-01

One of the key aspects influencing microstructural design pathways in metallic systems is grain boundary motion. The present work introduces a method by means of which direct measurement of grain boundary mobility vs. misorientation dependence is made possible. The technique utilizes datasets acquired by means of serial electron backscatter diffraction (EBSD) measurements. The experimental EBSD measurements are collectively analyzed, whereby datasets were used to obtain grain boundary mobility and grain aspect ratio with respect to grain boundary misorientation. The proposed method is further validated using cellular automata (CA) simulations. Single crystal aluminium was cold rolled and scratched in order to nucleate random orientations. Subsequent annealing at 300 °C resulted in grains growing, in the direction normal to the scratch, into a single deformed orientation. Growth selection was observed, wherein the boundaries with misorientations close to Σ7 CSL orientation relationship (38° 〈111〉) migrated considerably faster. The obtained boundary mobility distribution exhibited a non-monotonic behavior with a maximum corresponding to misorientation of 38° ± 2° about 〈111〉 axes ± 4°, which was 10–100 times higher than the mobility values of random high angle boundaries. Correlation with the grain aspect ratio values indicated a strong growth anisotropy displayed by the fast growing grains. The observations have been discussed in terms of the influence of grain boundary character on grain boundary motion during recrystallization. - Highlights: • Statistical microstructure method to measure grain boundary mobility during recrystallization • Method implementation independent of material or crystal structure • Mobility of the Σ7 boundaries in 5N Al was calculated as 4.7 × 10"–"8 m"4/J ⋅ s. • Pronounced growth selection in the recrystallizing nuclei in Al • Boundary mobility values during recrystallization 2–3 orders of magnitude

Incorporation of Eu(III) into calcite under recrystallization conditions

International Nuclear Information System (INIS)

Hellebrandt, S.E.; Jordan, Norbert; Barkleit, Astrid; Schmidt, Moritz; Hofmann, S.

2017-01-01

The interaction of three calcite powders with Eu(III) under recrystallization conditions was studied on the molecular level using site-selective time-resolved laser fluorescence spectroscopy (TRLFS). Batch contact studies with reaction times from 1 week up to 3 years revealed that the speciation differs from that observed previously in co-precipitation experiments and is dominated by a newly identified species ''γ''. The speed of formation of this species was found to depend greatly on the recrystallization rate of the studied minerals.

Incorporation of Eu(III) into calcite under recrystallization conditions

Energy Technology Data Exchange (ETDEWEB)

Hellebrandt, S.E. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Inst. of Resource Ecology; Jordan, Norbert [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes; Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Chemistry of the F-Elements; Schmidt, Moritz [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). HGF Young Investigator Group; Hofmann, S.

2017-06-01

The interaction of three calcite powders with Eu(III) under recrystallization conditions was studied on the molecular level using site-selective time-resolved laser fluorescence spectroscopy (TRLFS). Batch contact studies with reaction times from 1 week up to 3 years revealed that the speciation differs from that observed previously in co-precipitation experiments and is dominated by a newly identified species ''γ''. The speed of formation of this species was found to depend greatly on the recrystallization rate of the studied minerals.

Improvement of seawater salt quality by hydro-extraction and re-crystallization methods

Science.gov (United States)

Sumada, K.; Dewati, R.; Suprihatin

2018-01-01

Indonesia is one of the salt producing countries that use sea water as a source of raw materials, the quality of salt produced is influenced by the quality of sea water. The resulting average salt quality contains 85-90% NaCl. The Indonesian National Standard (SNI) for human salt’s consumption sodium chloride content is 94.7 % (dry base) and for industrial salt 98,5 %. In this study developed the re-crystallization without chemical and hydro-extraction method. The objective of this research to choose the best methods based on efficiency. The results showed that re-crystallization method can produce salt with NaCl content 99,21%, while hydro-extraction method content 99,34 % NaCl. The salt produced through both methods can be used as a consumption and industrial salt, Hydro-extraction method is more efficient than re-crystallization method because re-crystallization method requires heat energy.

Analysis of recrystallization and grain growth in ultra low carbon steels using EBSD

International Nuclear Information System (INIS)

Novillo, E.; Petite, M. M.; Bocos, J. L.; Gutierrez, I.

2004-01-01

This work is focused on the study of recrystallization texture and micro texture in a cold rolled ultra low carbon steel and its relationship with the global texture. Aspects like nucleation, evolution of the volume fraction and grain size were considered. An important grain selection associated with a significant size and number advantages of the recrystallized grains is observed. This grain selection gives rise to the development, at the latest stages of recrystallization, of a strong γ-fibre associated to good drawing properties. (Author) 24 refs

Microstructure and annealing behavior of a modified 9Cr−1Mo steel after dynamic plastic deformation to different strains

International Nuclear Information System (INIS)

Zhang, Z.B.; Mishin, O.V.; Tao, N.R.; Pantleon, W.

2015-01-01

The microstructure, hardness and tensile properties of a modified 9Cr−1Mo steel processed by dynamic plastic deformation (DPD) to different strains (0.5 and 2.3) have been investigated in the as-deformed and annealed conditions. It is found that significant structural refinement and a high level of strength can be achieved by DPD to a strain of 2.3, and that the microstructure at this strain contains a large fraction of high angle boundaries. The ductility of the DPD processed steel is however low. Considerable structural coarsening of the deformed microstructure without pronounced recrystallization takes place during annealing of the low-strain and high-strain samples for 1 h at 650 °C and 600 °C, respectively. Both coarsening and partial recrystallization occur in the high-strain sample during annealing at 650 °C for 1 h. For this sample, it is found that whereas coarsening alone results in a loss of strength with only a small gain in ductility, coarsening combined with pronounced partial recrystallization enables a combination of appreciably increased ductility and comparatively high strength

Unraveling Recrystallization Mechanisms Governing Texture Development from Rare Earth Element Additions to Magnesium

Science.gov (United States)

Imandoust, Aidin

The origin of texture components associated with rare-earth (RE) element additions in wrought magnesium (Mg) alloys is a long-standing problem in magnesium technology. The objective of this research is to identify the mechanisms accountable for rare-earth texture during dynamic recrystallization (DRX). Towards this end, we designed binary Mg-Cerium and Mg-Gadolinium alloys along with complex alloy compositions containing zinc, yttrium and Mischmetal. Binary alloys along with pure Mg were designed to individually investigate their effects on texture evolutions, while complex compositions are designed to develop randomized texture, and be used in automotive and aerospace applications. We selected indirect extrusion to thermo-mechanically process our materials. Different extrusion ratios and speeds were designed to produce partially and fully recrystallized microstructures, allowing us to analyze DRX from its early stages to completion. X-ray diffraction, electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were used to conduct microstructure and texture analyses. Our analyses revealed that rare-earth elements in zinc-containing magnesium alloys promote discontinuous dynamic recrystallization at the grain boundaries. During nucleation, the effect of rare earth elements on orientation selection was explained by the concomitant actions of multiple Taylor axes in the same grain. Isotropic grain growth was observed due to rare earth elements segregating to grain boundaries, which lead to texture randomization. The nucleation in binary Mg-RE alloys took place by continuous formation of necklace structures. Stochastic relaxation of basal and non-basal dislocations into low-angle grain boundaries produced chains of embryos with nearly random orientations. Schmid factor analysis showed a lower net activation of dislocations in RE textured grains compared to ones on the other side of the stereographic triangle. Lower dislocation densities within

Inhibition of Recrystallization of Amorphous Lactose in Nanocomposites Formed by Spray-Drying.

Science.gov (United States)

Hellrup, Joel; Alderborn, Göran; Mahlin, Denny

2015-11-01

This study aims at investigating the recrystallization of amorphous lactose in nanocomposites. In particular, the focus is on the influence of the nano- to micrometer length scale nanofiller arrangement on the amorphous to crystalline transition. Further, the relative significance of formulation composition and manufacturing process parameters for the properties of the nanocomposite was investigated. Nanocomposites of amorphous lactose and fumed silica were produced by co-spray-drying. Solid-state transformation of the lactose was studied at 43%, 84%, and 94% relative humidity using X-ray powder diffraction and microcalorimetry. Design of experiments was used to analyze spray-drying process parameters and nanocomposite composition as factors influencing the time to 50% recrystallization. The spray-drying process parameters showed no significant influence. However, the recrystallization of the lactose in the nanocomposites was affected by the composition (fraction silica). The recrystallization rate constant decreased as a function of silica content. The lowered recrystallization rate of the lactose in the nanocomposites could be explained by three mechanisms: (1) separation of the amorphous lactose into discrete compartments on a micrometer length scale (compartmentalization), (2) lowered molecular mobility caused by molecular interactions between the lactose molecules and the surface of the silica (rigidification), and/or (3) intraparticle confinement of the amorphous lactose. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Behaviors of Deformation, Recrystallization and Textures Evolution of Columnar Grains in 3%Si Electrical Steel Slabs

Directory of Open Access Journals (Sweden)

SHAO Yuan-yuan

2017-11-01

Full Text Available The behaviors of deformation and recrystallization and textures evolution of 3% (mass fraction Si columnar-grained electrical steel slabs were investigated by electron backscatter diffractometer technique and X-ray diffraction. The results indicate that the three columnar-grained samples have different initial textures with the long axes arranged along rolling, transverse and normal directions. Three shear orientations can be obtained in surface layer after hot rolling, of which Goss orientation is formed easily. The α and γ fibre rolling orientations are obtained in RD sample, while strong γ fibre orientations in TD sample and sharp {100} orientations in ND sample are developed respectively. In addition, cube orientation can be found in all the three samples. The characteristics of hot rolled orientations in center region reveal distinct dependence on initial columnar-grained orientations. Strong {111}〈112〉 orientation in RD and TD samples separately comes from Goss orientation of hot rolled sheets, and sharp rotated cube orientation in ND sample originates from the initial {100} orientation of hot rolled sheets after cold rolling. Influenced by initial deviated orientations and coarse grain size, large orientation gradient of rotated cube oriented grain can be observed in ND sample. The coarse {100} orientated grains of center region in the annealed sheets show the heredity of the initial columnar-grained orientations.

Mechanism of Dynamic Recrystallization and Evolution of Texture in the Hot Working Domains of the Processing Map for Mg-4Al-2Ba-2Ca Alloy

Directory of Open Access Journals (Sweden)

Kalidass Suresh

2017-12-01

Full Text Available The occurrence of dynamic recrystallization (DRX and its effect on the evolution of texture during uniaxial compression of a creep-resistant cast Mg-4Al-2Ba-2Ca alloy in the temperature range of 260–500 °C and strain rate range of 0.0003–10 s−1 has been studied using transmission electron microscopy and electron backscatter diffraction techniques with a view to understand its mechanism. For this purpose, a processing map has been developed for this alloy, which revealed two domains of DRX in the temperature and strain rate ranges of: (1 300–390 °C/0.0003–0.001 s−1 and (2 400–500 °C/0.0003–0.5 s−1. In Domain 1, DRX occurs by basal slip and recovery by dislocation climb, as indicated by the presence of planar slip bands and high dislocation density leading to tilt boundary formation and a low-intensity basal texture. On the other hand, DRX in Domain 2 occurs by second order pyramidal slip and recovery by cross-slip since the microstructure revealed tangled dislocation structure with twist boundaries and randomized texture. The high volume content of intermetallic phases Mg21Al3Ba2 and (Al,Mg2Ca eutectic phase is considered to be responsible for the observed hot deformation behavior.

On the origin of recrystallization textures

Indian Academy of Sciences (India)

Unknown

rival theories of evolution of recrystallization textures i.e. oriented nucleation (ON) and oriented growth (OG) has been under dispute. In the ON model, it has been argued that a higher frequency of the special orientation. (grains) than random occur, thus accounting for the texture. In the OG model, it has been argued that the.

Contribution to study on recovery and recrystallization of cold rolling zircaloy-4

International Nuclear Information System (INIS)

Persiano, A.I.C.

1977-01-01

Recovery and recrystallization of work-hardened (40-60% - Cold rolling) Zircaloy-4 were studied between 200 and 600 0 C with times varying from 15 to 240 minutes, from electrical resistance and hardness measurements. Activation energy calculation for the recovery and recrystallization processes using the samples work-hardened 60% gave 0,7 and 2,1 eV. (author)

Nondestructive characterization of recovery and recrystallization in cold rolled low carbon steel by magnetic hysteresis loops

International Nuclear Information System (INIS)

Martinez-de-Guerenu, A.; Gurruchaga, K.; Arizti, F.

2007-01-01

How structure sensitive parameters derived from hysteresis loops can provide nondestructive information about the evolution of the microstructure of cold rolled low carbon steel as a result of recovery and recrystallization processes during the annealing is shown. The coercive field, remanent induction and hysteresis losses can be used to monitor the decrease in the dislocation density during recovery. These parameters are also influenced by the average grain refinement that takes place during recrystallization, which compensates the variation produced by the annihilation of dislocations during recrystallization. The maximum of the induction and of the relative differential permeability are shown to be very sensitive to the onset and to the monitoring of the recrystallization, respectively. The correlations between coercive field and remanent induction and hysteresis losses can also be used to distinguish between recovery and recrystallization

Importance of Local Structural Variations on Recrystallization

DEFF Research Database (Denmark)

Juul Jensen, Dorte; Lin, Fengxiang; Zhang, Yubin

2013-01-01

Effects of local variations in the deformation microstructure on subsequent recrystallization are discussed and illustrated by three examples. The three examples consider local variations on different length scales and are: 1. Effects of local variations in the deformation microstructure on the f...

Mixed Solvent Reactive Recrystallization of Sodium Carbonate

NARCIS (Netherlands)

Gaertner, R.S.

2005-01-01

Investigation of the reactive recrystallization of trona (sodium sesquicarbonate) and sodium bicarbonate to sodium carbonate (soda) in a mixed solvent led to the design of several alternative, less energy consumptive, economically very attractive process routes for the production of soda from all

Characterization of hot deformation behavior and processing map of FGH4096–GH4133B dual alloys

Energy Technology Data Exchange (ETDEWEB)

Liu, Yanhui; Ning, Yongquan, E-mail: ningke521@163.com; Nan, Yang; Liang, Houquan; Li, Yuzhi; Zhao, Zhanglong

2015-06-05

Highlights: • Hot deformation behavior of dual superalloys FGH4096–GH4133B was investigated. • Power dissipation maps built at different strains exhibit a continuous dynamic course. • Processing map approach was adopted to optimize hot forging process for dual superalloys. • Microstructure evolution at different deformation temperature and strain rate of dual superalloys was researched. - Abstract: The dual superalloys FGH4096–GH4133B were joined by the electron beam welding. Isothermal compression tests were carried out on electron beam weldments FGH4096–GH4133B alloys at the temperatures of 1020–1140 °C (the nominal γ′-transus temperature is about 1080 °C) and strain rates of 0.001–1.0 s{sup −1} with the height reduction of 50%. The results showed that the true stress–true strain curves are greatly affected by deformation temperature and strain rate. There is an intrinsic and necessary connection between the flow stress and thermal–dynamic behavior, which can be indicated by the true stress–true strain curves. The power dissipation maps at different strains exhibit that true strain has a great effect on processing maps. Processing maps under different strains were constructed for evaluation of the flow instability regime and optimization of processing parameters. When the true strain is 0.69, the optimum processing condition is around 1090−1130 °C/0.1−1.0 s{sup −1} with the peak efficiency of 0.58. The dynamic recrystallization mechanism and microstructure evolution in the welding seam of the studied dual-alloys have been discussed. High temperature and low strain rate are instrumental to dynamic recrystallization. The size of dynamically recrystallized grain decreased with the increase of strain rate and increased with the increase of deformation temperature. Based on the established combine processing map and microstructures, hot deformation process should be carried out under the condition of 1100−1120 °C/0.3−1.0 s

Characterization of hot deformation behavior and processing map of FGH4096–GH4133B dual alloys

International Nuclear Information System (INIS)

Liu, Yanhui; Ning, Yongquan; Nan, Yang; Liang, Houquan; Li, Yuzhi; Zhao, Zhanglong

2015-01-01

Highlights: • Hot deformation behavior of dual superalloys FGH4096–GH4133B was investigated. • Power dissipation maps built at different strains exhibit a continuous dynamic course. • Processing map approach was adopted to optimize hot forging process for dual superalloys. • Microstructure evolution at different deformation temperature and strain rate of dual superalloys was researched. - Abstract: The dual superalloys FGH4096–GH4133B were joined by the electron beam welding. Isothermal compression tests were carried out on electron beam weldments FGH4096–GH4133B alloys at the temperatures of 1020–1140 °C (the nominal γ′-transus temperature is about 1080 °C) and strain rates of 0.001–1.0 s −1 with the height reduction of 50%. The results showed that the true stress–true strain curves are greatly affected by deformation temperature and strain rate. There is an intrinsic and necessary connection between the flow stress and thermal–dynamic behavior, which can be indicated by the true stress–true strain curves. The power dissipation maps at different strains exhibit that true strain has a great effect on processing maps. Processing maps under different strains were constructed for evaluation of the flow instability regime and optimization of processing parameters. When the true strain is 0.69, the optimum processing condition is around 1090−1130 °C/0.1−1.0 s −1 with the peak efficiency of 0.58. The dynamic recrystallization mechanism and microstructure evolution in the welding seam of the studied dual-alloys have been discussed. High temperature and low strain rate are instrumental to dynamic recrystallization. The size of dynamically recrystallized grain decreased with the increase of strain rate and increased with the increase of deformation temperature. Based on the established combine processing map and microstructures, hot deformation process should be carried out under the condition of 1100−1120 °C/0.3−1.0 s −1 with

Effect of microalloying with rare-earth on recrystallization behaviour and damping properties of Mg sheets

International Nuclear Information System (INIS)

Ma, Ning; Peng, Qiuming; Pan, Junling; Li, Hui; Xiao, Wenlong

2014-01-01

Highlights: • Rare earth additions accelerate recovery, but retard recrystallization. • Internal peak at mediate temperatures corresponds to grain boundary relaxation. • Internal peak at elevated temperature is a recrystallization peak. • Grain size, basal texture and dislocation density affect damping remarkably. - Abstract: The effect of a small amount of rare earth elements (RE: Nd and Dy, 0.5 wt.%) on recrystallization behaviour, microstructural evolution and damping properties of deformed Mg sheets have been investigated. The recrystallization behaviour was analyzed in terms of the Johnson–Mehl–Avrami–Kolmogorov model via the variation of microhardness. The Avrami exponent of pure Mg sheet ranged from 1.02 to 1.16, and it was reduced by adding REs. The acceleration of recovery and retardation of recrystallization were detected by the presence of REs. Three point bending was carried out to assess damping properties. At the temperature of ∼150 °C, the damping peak corresponds to grain boundary relaxation, which was affected by grain size, basal texture and the variation of dislocation density on basal plane. At elevated temperatures, a non-thermal activated peak was mainly dependent upon annealing condition, where its height and temperature were increased by adding REs, assigning to be a recrystallization peak

Effects of recrystallization annealing on mechanical properties of cold-rolled PdNi5 wires

Directory of Open Access Journals (Sweden)

Aleksandra Ivanović

2016-03-01

Full Text Available The aim of this investigation was to determine the influence of the recrystallization temperature and recrystallization time on the microstructure and mechanical properties of the PdNi5 alloy subjected to cold deformation in the process of rolling at a constant deformation degree. The samples of PdNi5 alloy were recrystallization annealed within the temperature range of 200-1000ºC and annealing time range of 20-45 min after cold rolling with deformation degree of 97%. The tensile test was carried out using universal material testing machine. The hardness was also measured on the combined device for measuring Vickers and Brinell hardness. Metallographic observations were performed on an optical microscope. The analysis of the results of investigations regarding the microstructural changes and corresponding mechanical properties of cold-rolled PdNi5 strips shows that annealing temperature of 500ºC was sufficient to activate the energy for various recrystallization processes causing a change in the mechanical properties of cold-rolled PdNi5 strips. The annealing time, at constant annealing temperature, almost did not affect a recrystallization temperature and the mechanical properties of the cold-rolled PdNi5 strips.

Recrystallization phenomena of solution grown paraffin dendrites

NARCIS (Netherlands)

Hollander, F.F.A.; Hollander, F.; Stasse, O.; van Suchtelen, J.; van Enckevort, W.J.P.

2001-01-01

Paraffin crystals were grown from decane solutions using a micro-Bridgman set up for in-situ observation of the morphology at the growth front. It is shown that for large imposed velocities, dendrites are obtained. After dendritic growth, aging or recrystallization processes set in rather quickly,

Thermal behaviour in dynamic recrystallisation. Application for iron base alloys

International Nuclear Information System (INIS)

Belkebir, A.; Kobylanski, A.

1995-01-01

A constitutive relationship for predicting the flow stress with dynamic recrystallization were proposed. The approach is based on a phenomenological formalism of the law θ-ε where θ correspond to the work-hardening rate at constant strain rate and temperature. The equations proposed were justified by the experimental data collected by hot compression test of low-alloy steels. The model can be used to estimate the critical strain for the onset of dynamic recrystallization. (orig.)

Recrystallization kinetics of warm-rolled tungsten in the temperature range 1150-1350 °C

Science.gov (United States)

Alfonso, A.; Juul Jensen, D.; Luo, G.-N.; Pantleon, W.

2014-12-01

Pure tungsten is a potential candidate material for the plasma-facing first wall and the divertor of fusion reactors. Both parts have to withstand high temperatures during service. This will alter the microstructure of the material by recovery, recrystallization and grain growth and will cause degradation in material properties as a loss in mechanical strength and embrittlement. The thermal stability of a pure tungsten plate warm-rolled to 67% thickness reduction was investigated by long-term isothermal annealing in the temperature range between 1150 °C and 1350 °C up to 2200 h. Changes in the mechanical properties during annealing are quantified by Vickers hardness measurements. They are described concisely by classical kinetic models for recovery and recrystallization. The observed time spans for recrystallization and the obtained value for the activation energy of the recrystallization process indicate a sufficient thermal stability of the tungsten plate during operation below 1075 °C.

Orientation effect on recovery and recrystallization of cold rolled niobium single crystals

Energy Technology Data Exchange (ETDEWEB)

Srinivasan, R. [Center for Accelerated Maturation of Materials, Department of Materials Science and Engineering, Ohio State University, Columbus, OH 43210 (United States)], E-mail: rajagopalan.5@osu.edu; Viswanathan, G.B.; Levit, V.I.; Fraser, H.L. [Center for Accelerated Maturation of Materials, Department of Materials Science and Engineering, Ohio State University, Columbus, OH 43210 (United States)

2009-05-15

Single crystal sheets of niobium with initial orientations of (0 0 1) [11-bar0], (1 1 0) [11-bar 0] and (1 1 1) [11-bar0] were rolled at room temperature in the strain range of 25-50%. The deformed specimens were vacuum annealed at temperatures of 800 deg. C, 1000 deg. C, and 1200 deg. C for 3 h. TEM, SEM-OIM and optical microscopy revealed orientation stability in (0 0 1) and (1 1 0) rolled samples with no recrystallization observed after annealing. Samples rolled along (1 1 1) partially recrystallized after annealing at 1000 deg. C and 1200 deg. C. A relatively small increase was observed in hardness of (0 0 1) rolled crystals between 25% and 50% strain, implying low work hardening rates. (1 1 1) rolled samples showed higher hardening rates, and enhanced recovery in hardness values after annealing, due to partial recrystallization. Conditions have been identified for the deformation and annealing of niobium single crystals, enabling the preservation of single crystal structure and near-complete recovery of mechanical properties. A simple crystallographic model is proposed, giving an explanation for the observed orientation stability in (0 0 1) and (1 1 0) rolled samples, and the tendency towards instability and recrystallization in (1 1 1) rolled samples.

Hot deformation behavior of delta-processed superalloy 718

Energy Technology Data Exchange (ETDEWEB)

Wang, Y., E-mail: wangyanhit@yahoo.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); School of Aeronautics and Astronautics, Central South University, Changsha 410083 (China); Shao, W.Z.; Zhen, L.; Zhang, B.Y. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)

2011-03-25

Research highlights: {yields} The peak stress for hot deformation can be described by the Z parameter. {yields} The grain size of DRX was inversely proportional to the Z parameter. {yields} The dissolution of {delta} phases was greatly accelerated under hot deformation. {yields}The {delta} phase stimulated nucleation can serve as the main DRX mechanism. - Abstract: Flow stress behavior and microstructures during hot compression of delta-processed superalloy 718 at temperatures from 950 to 1100 deg. C with strain rates of 10{sup -3} to 1 s{sup -1} were investigated by optical microscopy (OM), electron backscatter diffraction (EBSD) technique and transmission electron microscopy (TEM). The relationship between the peak stress and the deformation conditions can be expressed by a hyperbolic-sine type equation. The activation energy for the delta-processed superalloy 718 is determined to be 467 kJ/mol. The change of the dominant deformation mechanisms leads to the decrease of stress exponent and the increase of activation energy with increasing temperature. The dynamically recrystallized grain size is inversely proportional to the Zener-Hollomon (Z) parameter. It is found that the dissolution rate of {delta} phases under hot deformation conditions is much faster than that under static conditions. Dislocation, vacancy and curvature play important roles in the dissolution of {delta} phases. The main nucleation mechanisms of dynamic recrystallization (DRX) for the delta-processed superalloy 718 include the bulging of original grain boundaries and the {delta} phase stimulated DRX nucleation, which is closely related to the dissolution behavior of {delta} phases under certain deformation conditions.

Deformation and recrystallization textures in commercially pure aluminum

DEFF Research Database (Denmark)

Hansen, Niels; Juul Jensen, Dorte

1986-01-01

The deformation and recrystallization textures of commercially pure aluminum (99.6 pct) containing large intermetallic particles (FeAl3) are measured by neutron diffraction, and the orientation distribution functions (ODF’s) are calculated. Sample parameters are the initial grain size (50 and 350...

Roughness of grain boundaries in partly recrystallized aluminum

DEFF Research Database (Denmark)

Sun, Jun; Zhang, Yubin; Juul Jensen, Dorte

2017-01-01

cold rolled aluminum samples. The results show that particle pinning is not the main reason accounting for recrystallization boundary roughness in the present samples. The roughness is however shown to relate to the deformation microstructure and possible effects of migration rate are discussed...

Magnetic properties and recrystallization texture of phosphorus-added non-oriented electrical steel sheets

International Nuclear Information System (INIS)

Tanaka, I.; Yashiki, H.

2006-01-01

The effect of phosphorus on magnetic properties and recrystallization texture has been investigated in non-oriented electrical steel sheets to develop low core loss and high permeability core materials. Specimens with different phosphorus contents were cold-rolled to various thicknesses, i.e. with various cold-rolling reductions, and annealed for recrystallization and grain growth. Although magnetic induction of the steel with low phosphorus content dramatically dropped with reducing thickness, i.e. with increasing in cold-rolling reduction, that of the steel with high phosphorus content only slightly decreased. The most effective way to reduce core loss was to reduce thickness of electrical steel sheets. Therefore, phosphorus-added thin gauge non-oriented electrical steel sheets have achieved low core loss and high permeability. The typical magnetic properties of phosphorus-added non-oriented electrical steel sheets 0.27mm in sheet thickness were 16.6W/kg in W 10/400 and 1.73T in B 50 . These excellent magnetic properties were due to the recrystallization texture control. {111} component in recrystallization texture was suppressed by the phosphorus segregation at initial grain boundaries. Accordingly, phosphorus would greatly contribute to the improvement of magnetic properties

A new methodology based on ultrasonic attenuation to characterize dynamically recrystallized microstructure in a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel

International Nuclear Information System (INIS)

Mandal, S.; Kumar, A.; Sivaprasad, P.V.; Jayakumar, T.; Baldev Raj; Kumar, S.; Samajdar, I.

2010-01-01

In this study, a C-scan ultrasonic imaging system has been employed for imaging the microstructural variations during dynamic recrystallization (DRX) of a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel. Four specimens were forged at 1273 K for different strains in the range of 0.1-0.5. It has been observed that the specimen with 0.2 strain or lower did not show any variation in the amplitude of the first backwall echo. However, at and above 0.3 strain, a visible variation in the C-scan images has been observed. This variation has been attributed to the evolution of fine grains. The formation of fine grains, on the other hand, was related to DRX, as indicated by electron back scattered diffraction (EBSD). (author)

Flow behavior and microstructures of powder metallurgical CrFeCoNiMo0.2 high entropy alloy during high temperature deformation

Energy Technology Data Exchange (ETDEWEB)

Wang, Jiawen [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Yong, E-mail: yonliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Bin, E-mail: binliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Wang, Yan [School of Aeronautics and Astronautics, Central South University, Changsha 410083 (China); Cao, Yuankui; Li, Tianchen; Zhou, Rui [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2017-03-24

Dynamic recrystallization (DRX) refine grains of high entropy alloys (HEAs) and significant improve the mechanical property of HEAs, but the effect of high melting point element molybdenum (Mo) on high temperature deformation behavior has not been fully understood. In the present study, flow behavior and microstructures of powder metallurgical CrFeCoNiMo{sub 0.2} HEA were investigated by hot compression tests performed at temperatures ranging from 700 to 1100 °C with strain rates from 10{sup −3} to 1 s{sup −1}. The Arrhenius constitutive equation with strain-dependent material constants was used for modeling and prediction of flow stress. It was found that at 700 °C, the dynamic recovery is the dominant softening mechanism, whilst with the increase in compression testing temperature, the DRX becomes the dominant mechanism of softening. In the present HEA, the addition of Mo results in the high activation energy (463 kJ mol{sup −1}) and the phase separation during hot deformation. The formation of Mo-rich σ phase particles pins grain boundary migration during DRX, and therefore refines the size of recrystallized grains.

Recrystallization textures and microstructures of Al-0.3%Cu alloy after deformation to high strains

DEFF Research Database (Denmark)

Li, X.R.; Wakeel, A.; Huang, T.L.

2015-01-01

An Al-0.3%Cu alloy was deformed to high strains by cold rolling. The as-deformed samples were annealed at different temperatures until complete recrystallization. The cold rolling textures were determined by X-ray diffraction while the recrystallization textures and microstructures were...

Oriented growth during recrystallization revisited in three dimensions

DEFF Research Database (Denmark)

Fan, Guohua; Zhang, Yubin; Driver, J. H.

2014-01-01

The two surfaces of a 40% cold-rolled tricrystal of aluminium were scratched to stimulate recrystallization nucleation. Serial sectioning combined with electron backscatter diffraction was used to characterize the nuclei in three dimensions. It was found that the largest nuclei have a 40 degrees

Local boundary migration during recrystallization in pure aluminium

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andrew; Juul Jensen, Dorte

2011-01-01

than generally appreciated. Locally protrusions/retrusions can provide a driving force comparable in magnitude to the driving force from the stored energy in the deformed matrix. The stop–go motion of the recrystallization boundaries is also discussed and related to the formation of protrusions...

Fabrication of wire and flat strips with elevated recrystallization temperature of Mo monocrystals

International Nuclear Information System (INIS)

Mikhajlov, S.M.; Nesgovorov, V.V.; Kabakova, L.G.; Korzukhin, V.E.; Savitskij, E.M.; Burkhanov, G.S.; Ottenberg, E.V.

1977-01-01

A technique is developed for manufacturing wire and flat strip of elevated recrystallization point from single crystals fo molybdenum with micro-additions of zirconium and titanium by rotary hot forging with subsequent drawing under hydrodynamic friction conditions. Flat strip is manufactured next from a wire annealed at 1300-1400 deg C in hydrogen. Resultant wire and flat strip feature a high recrystallization point and a good shape stability. Tests on their ultimate strength on the range of temperatures between 20 and 1700 deg C have shown that the maximum temperature of the recrystallization onset is that of a wire from Mo single crystals of orientation [110], containing micro-additions of Zr and Ti, whereas loss of strength is at its highest in a wire from non-alloyed single-crystal molybdenum

3D microstructural evolution of primary recrystallization and grain growth in cold rolled single-phase aluminum alloys

Science.gov (United States)

Adam, Khaled; Zöllner, Dana; Field, David P.

2018-04-01

Modeling the microstructural evolution during recrystallization is a powerful tool for the profound understanding of alloy behavior and for use in optimizing engineering properties through annealing. In particular, the mechanical properties of metallic alloys are highly dependent upon evolved microstructure and texture from the softening process. In the present work, a Monte Carlo (MC) Potts model was used to model the primary recrystallization and grain growth in cold rolled single-phase Al alloy. The microstructural representation of two kinds of dislocation densities, statistically stored dislocations and geometrically necessary dislocations were quantified based on the ViscoPlastic Fast Fourier transform method. This representation was then introduced into the MC Potts model to identify the favorable sites for nucleation where orientation gradients and entanglements of dislocations are high. Additionally, in situ observations of non-isothermal microstructure evolution for single-phase aluminum alloy 1100 were made to validate the simulation. The influence of the texture inhomogeneity is analyzed from a theoretical point of view using an orientation distribution function for deformed and evolved texture.

Influence of polymer chain architecture of poly(vinyl alcohol) on the inhibition of ice recrystallization

NARCIS (Netherlands)

Olijve, L.L.C.; Hendrix, M.M.R.M.; Voets, I.K.

2016-01-01

Poly(vinyl alcohol) (PVA) is a water-soluble synthetic polymer well-known to effectively block the recrystallization of ice. The effect of polymer chain architecture on the ice recrystallization inhibition (IRI) by PVA remains unexplored. In this work, the synthesis of PVA molecular bottlebrushes is

Conversion of Jatropha curcas oil into biodiesel using re-crystallized hydrotalcite

International Nuclear Information System (INIS)

Helwani, Z.; Aziz, N.; Bakar, M.Z.A.; Mukhtar, H.; Kim, J.; Othman, M.R.

2013-01-01

Graphical abstract: XRD pattern of a mixed oxide and re-crystallized hydrotalcite after contacting with carbonate solution. The sample re-crystallized despite being exposed to high temperature. The increased crystallinity at higher calcination temperature was due to aluminum progressively incorporated into the MgO network. At low temperature, aluminum diffused slowly and did not reach the crystallite core. XRD pattern of (a) mixed oxide at 450 °C, (b) hydrotalcite at 450 °C (c) hydrotalcite at 650 °C and (d) hydrotalcite at 850 °C. - Highlights: • Synthetic hydrotalcite (HT) was prepared from combustion method. • The sample was able to re-crystallize despite being exposed to high temperature. • HT catalyst promoted conversion of Jatropha curcas oil into biodiesel. • Conversion of 75.2% was achieved with promising conditions. - Abstract: Biodiesel production from biomass is considered renewable and the use of biomass offers huge opportunity in bio-based economy market. In this work, biodiesel was produced from Jatropha curcas oil using synthetic hydrotalcite (HT) catalyst. The catalyst was obtained through combustion, in which, saccharose was used as fuel. The highest conversion of jatropha oil to biodiesel at 75.2% was achieved using re-crystallized HT from its mixed oxides when reaction was carried out at 65 °C with a methanol:jatropha oil molar ratio of 12:1, a reaction time of 6 h and a catalyst loading of 4 wt.%. The HT calcined at 850 °C contained medium basic strength sites and suitable pore medium that favored the chemical reaction

Recrystallization kinetics of warm-rolled tungsten in the temperature range 1150–1350 °C

Energy Technology Data Exchange (ETDEWEB)

Alfonso, A., E-mail: aalz@dtu.dk [Section of Materials and Surface Engineering, Department of Mechanical Engineering, Technical University of Denmark, 2800 Lyngby (Denmark); Sino-Danish Center for Education and Research (China); Sino-Danish Center for Education and Research (Denmark); Juul Jensen, D. [Danish-Chinese Center for Nanometals, Section of Materials Science and Advanced Characterization, Department of Wind Energy, Technical University of Denmark, Risø Campus, 4000 Roskilde (Denmark); Sino-Danish Center for Education and Research (China); Sino-Danish Center for Education and Research (Denmark); Luo, G.-N. [Fusion Reactor Materials Science and Technology Division, Institute of Plasma Physics, Chinese Academy of Sciences, 230031 Hefei, Anhui (China); Sino-Danish Center for Education and Research (China); Sino-Danish Center for Education and Research (Denmark); Pantleon, W. [Section of Materials and Surface Engineering, Department of Mechanical Engineering, Technical University of Denmark, 2800 Lyngby (Denmark); Association EURATOM-DTU (Denmark); Sino-Danish Center for Education and Research (China); Sino-Danish Center for Education and Research (Denmark)

2014-12-15

Pure tungsten is a potential candidate material for the plasma-facing first wall and the divertor of fusion reactors. Both parts have to withstand high temperatures during service. This will alter the microstructure of the material by recovery, recrystallization and grain growth and will cause degradation in material properties as a loss in mechanical strength and embrittlement. The thermal stability of a pure tungsten plate warm-rolled to 67% thickness reduction was investigated by long-term isothermal annealing in the temperature range between 1150 °C and 1350 °C up to 2200 h. Changes in the mechanical properties during annealing are quantified by Vickers hardness measurements. They are described concisely by classical kinetic models for recovery and recrystallization. The observed time spans for recrystallization and the obtained value for the activation energy of the recrystallization process indicate a sufficient thermal stability of the tungsten plate during operation below 1075 °C.

Recrystallization kinetics of warm-rolled tungsten in the temperature range 1150–1350 °C

International Nuclear Information System (INIS)

Alfonso, A.; Juul Jensen, D.; Luo, G.-N.; Pantleon, W.

2014-01-01

Pure tungsten is a potential candidate material for the plasma-facing first wall and the divertor of fusion reactors. Both parts have to withstand high temperatures during service. This will alter the microstructure of the material by recovery, recrystallization and grain growth and will cause degradation in material properties as a loss in mechanical strength and embrittlement. The thermal stability of a pure tungsten plate warm-rolled to 67% thickness reduction was investigated by long-term isothermal annealing in the temperature range between 1150 °C and 1350 °C up to 2200 h. Changes in the mechanical properties during annealing are quantified by Vickers hardness measurements. They are described concisely by classical kinetic models for recovery and recrystallization. The observed time spans for recrystallization and the obtained value for the activation energy of the recrystallization process indicate a sufficient thermal stability of the tungsten plate during operation below 1075 °C

Texture Of Zircaloy-4 Result Of Beta-Quenching, Cold Rolling And Recrystallization

International Nuclear Information System (INIS)

Futichah; Sulistioso

1998-01-01

Differences of crystallographic texture of zircaloy-4 plate depends on cold working and heat treatment.To determine the change of zircaloy-4 textures, the solid solution treatment process at beta phase which was followed by quenching on water was employed for this sample. The next step was cold rolling until deformation epsilon = 1.62. The specimens were recrystallized at 750 o C, for 2 hours. The result of beta-quench gave a spread and different orientations and the main orientation occurred at (0001)[1010] and (0001)[1120]. Result of cold rolling with epsilon = 1.39 and epsilon 1.62 is the deformation texture at the main orientation of (0001)[1010] with the angle of inclination was around 38 o. However, the result of Recrystallization process on 750 o C for 2 hours gave annealing textures with orientations of (0001)[1120]. It means that the recrystallization process of zircaloy-4 plate can not remove the deformation textures, but can change the crystallographic orientation

Ultra-low-angle boundary networks within recrystallizing grains

DEFF Research Database (Denmark)

Ahl, Sonja Rosenlund; Simons, Hugh; Zhang, Yubin

2017-01-01

We present direct evidence of a network of well-defined ultra-low-angle boundaries in bulk recrystallizing grains of 99.5% pure aluminium (AA1050) by means of a new, three-dimensional X-ray mapping technique; dark-field X-ray microscopy. These boundaries separate lattice orientation differences o...

Nucleation of Recrystallization studied by EBSP and 3DXRD

DEFF Research Database (Denmark)

West, Stine

2009-01-01

When a deformed crystalline material is annealed, recrystallization will typically take place. In this process new perfect crystals nucleate and grow, consuming the deformation structure. Traditionally, nucleation theories state that the crystal orientations of these new grains were already present...... in the deformed state, but several experiments have shown the emergence of what appears to be new orientations. The purpose of the present project was to observe nucleation of recrystallization both on surfaces and in the bulk. Special focus was on the possible formation of nuclei with orientations not present...... in the deformed matrix before annealing. To facilitate the nucleation studies, a well-annealed starting material was prepared from high-purity aluminum with a large average grain size and almost straight grain boundaries mostly forming triple junctions with angles close to 120°. The large grain size was necessary...

Microstructure and local texture of partially recrystallized titanium sheet

International Nuclear Information System (INIS)

Zaefferer, S.; Schwarzer, R.A.

1993-01-01

The microstructure of TiAl6V4 sheet was investigated by transmission electron microscopy. Two types of microstructure were found: regions with a recrystallized and regions with a deformed structure. They could be distinguished from each other by grain size and shape, by the dislocation density and local texture. The orientations of individual grains were measured by on-line interpretation of Kikuchi patterns with a TEM. The results were represented on inverse pole figures. The deformed structure showed a strong preferred orientation (11 anti 20)[10 anti 10], while the texture of the recrystallized areas was substantially weaker containing other preferred orientations. The global texture of the sample was investigated by measuring pole figures with an x-ray texture goniometer. The ODF as well as inverse pole figures were calculated and compared to the TEM pole figures. (orig.)

Combined Effect of Heating Rate and Microalloying Elements on Recrystallization During Annealing of Dual-Phase Steels

Science.gov (United States)

Bellavoine, Marion; Dumont, Myriam; Drillet, Josée; Hébert, Véronique; Maugis, Philippe

2018-05-01

Adjusting ferrite recrystallization kinetics during annealing is a way to control the final microstructure and thus the mechanical properties of advanced cold-rolled high-strength steels. Two strategies are commonly used for this purpose: adjusting heating rates and/or adding microalloying elements. The present work investigates the effect of heating rate and microalloying elements Ti, Nb, and Mo on recrystallization kinetics during annealing in various cold-rolled Dual-Phase steel grades. The use of combined experimental and modeling approaches allows a deeper understanding of the separate influence of heating rate and the addition of microalloying elements. The comparative effect of Ti, Nb, and Mo as solute elements and as precipitates on ferrite recrystallization is also clarified. It is shown that solute drag has the largest delaying effect on recrystallization in the present case and that the order of solute drag effectiveness of microalloying elements is Nb > Mo > Ti.

Modeling and Finite Element Analysis for the Dynamic Recrystallization Behavior of Ti-5Al-5Mo-5V-3Cr-1Zr Near β Titanium Alloy During Hot Deformation

Science.gov (United States)

Lv, Ya-ping; Li, Shao-jun; Zhang, Xiao-yong; Li, Zhi-you; Zhou, Ke-chao

2018-04-01

Evolution for the dynamic recrystallization (DRX) volume fraction of Ti-5Al-5Mo-5V-3Cr-1Zr near β titanium alloy during hot deformation was characterized by using the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation. To determine the equation parameters, a series of thermal simulation experiments at the temperature of 1023-1098 K and strain rate of 0.001-1 s‒1 to the true strain of 0.7 were conducted to obtain the essential data about stress σ and strain ɛ. By further transforming the relationship of σ versus ɛ into the relationship of strain hardening rate dσ/dɛ versus σ, two characteristic strains at the beginning of DRX (critical strain ɛc) and at the peak stress (peak strain ɛp) were identified from the dσ/dɛ-σ curves. Sequentially, the parameters in the JMAK equation were determined from the linear fitting of the different relationships among critical strain ɛc, peak strain ɛp and deformation conditions (including temperature T, strain rate \\dot ɛ and strain ɛ). The as-obtained JMAK equation was expressed as XDRX=1-exp[-0.0053((ɛ-ɛc)/ɛc)2.1], where ɛc=0.6053ɛp and ɛp=0.0031 \\dot ɛ .0081exp(28,781/RT). Finally, the JMAK equation was implanted into finite element program to simulate the hot compression of thermal simulation experiments. The simulation predictions and experimental results about the DRX volume fraction distribution showed a good consistency.

Recrystallization behaviour and electrical properties of germanium ion implanted polycrystalline silicon films

International Nuclear Information System (INIS)

Kang, Myeon-Koo; Matsui, Takayuki; Kuwano, Hiroshi

1996-01-01

The recrystallization behaviour of undoped and phosphorus-doped polycrystalline silicon films amorphized by germanium ion implantation at doses ranging from 1 x 10 15 to 1 x 10 16 cm -2 are investigated, and the electrical properties of phosphorus-doped films after recrystallization are studied. The phosphorus doping concentration ranges from 3 x 10 18 to 1 x 10 20 cm -3 . It is found that the nucleation rate decreases for undoped films and increases for phosphorus-doped films with increasing germanium dose; the growth rates decrease for both doped and undoped films. The decrease in nucleation rate is caused by the increase in implantation damage. The decrease in growth rate is considered to be due to the increase in lattice strain. The grain size increases with germanium dose for undoped films, but decreases for phosphorus-doped films. The dependence of the electrical properties of the recrystallized films as a function of phosphorus doping concentration with different germanium doses can be explained in terms of the grain size, crystallinity and grain boundary barrier height. (Author)

Mechanical and microstructural characteristics of an Al-Li-Cu-Zr alloy during superplastic deformation

International Nuclear Information System (INIS)

Ren, B.

1991-01-01

If the above alloys are heavily cold- or warm-worked prior to superplastic deformation, they are resistant to static recrystallization but dynamically recrystallize with a clear strain dependence, and are superplastic deformable at relative high strain rates in the approximate range of 10 -3 to 10 -1 s -1 . The microstructural source of superplasticity has been the subject of less-detailed study than the more classical fully recrystallized materials. In this study, an effort was made to provide a somewhat greater insight into the mechanical behavior during the dynamic recrystallization of an Al-Li-Cu-Zr alloy, and to relate the mechanical behavior to the microstructure and its evolution. As part of the study, internal stresses were measured by the strain dip test, and effective stresses and their development were determined over a range of temperatures and strain rates. mechanisms for the superplastic flow and the internal-stress development during the initial stage of deformation were suggested. A variable-strain-rate model was developed based on the understanding of the mechanical behavior of this material

Effect of Scandium on the Interaction of Concurrent Precipitation and Recrystallization in Commercial AA3003 Aluminum Alloy

Science.gov (United States)

Tu, Yiyou; Qian, Huan; Zhou, Xuefeng; Jiang, Jianqing

2014-04-01

In the current study, the effect of Sc addition on the interaction of concurrent precipitation and recrystallization in commercial AA3003 aluminum alloy was investigated using optical microscopy, scanning electron microscopy, and transmission electron microscopy. In case of AA3003 alloy, which was cold rolled to a true strain of 2.20 and heated at a heating rate of 150 K/s, the onset of precipitation and ending of recrystallization are signified by the critical temperature, T C ~740 K (467 °C). There is a change in the shape of the recrystallized grains from pancake-like to equiaxed shape, as the annealing temperature increases greater than T C. In case of AA3003 alloy microalloyed with 0.4 wt pct of Sc, the high no. density precipitation of coherent Al3Sc precipitates always occurs before recrystallization because of the small nucleation barrier and high rate of decomposition. This leads to extremely coarse pancake-like recrystallization grains with high fraction of low-angle grain boundaries in the entire annealing temperature range, even at a high brazing temperature of 883 K (610 °C).

New 3DXRD results on recrystallization and grain growth

DEFF Research Database (Denmark)

Juul Jensen, Dorte; West, Stine; Poulsen, Stefan Othmar

2012-01-01

New in-situ 3DXRD results obtained since the last Rex&GG conference are presented and discussed. This includes: Documentation of the formation of nuclei with new orientations, determination of apparent activation energies for individual bulk grains during recrystallization and evolution in the 3D...

In-Situ Investigation of Local Boundary Migration During Recrystallization

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andy; Juul Jensen, Dorte

2014-01-01

A combination of electron channeling contrast (ECC) and electron backscatter diffraction pattern (EBSP) techniques has been used to follow in situ the migration during annealing at 323 K (50 A degrees C) of a recrystallizing boundary through the deformed matrix of high-purity aluminum rolled to 8...

Hot Deformation Behavior of SA508Gr.4N Steel for Reactor Pressure Vessels

Directory of Open Access Journals (Sweden)

YANG Zhi-qiang

2017-08-01

Full Text Available The high-temperature plastic deformation and dynamic recrystallization behavior of SA508Gr.4N steel were investigated through hot deformation tests in a Gleeble1500D thermal mechanical simulator. The compression tests were performed in the temperature range of 1050-1250℃ and the strain rate range of 0.001-0.1s-1 with true strain of 0.16. The results show that from the high-temperature true stress-strain curves of the SA508Gr.4N steel, the main feature is dynamic recrystallization,and the peak stress increases with the decrease of deformation temperature or the increase of strain rate, indicating the experimental steel is temperature and strain rate sensitive material. The constitutive equation for SA508Gr.4N steel is established on the basis of the true stress-strain curves, and exhibits the characteristics of the high-temperature flow behavior quite well, while the activation energy of the steel is determined to be 383.862kJ/mol. Furthermore, an inflection point is found in the θ-σ curve, while the -dθ/dσ-σ curve shows a minimum value. The critical strain increases with increasing strain rate and decreasing deformation temperature. A linear relationship between critical strain (εc and peak strain (εp is found and could be expressed as εc/εp=0.517. The predicted model of critical strain could be described as εc=8.57×10-4Z0.148.

Recrystallization and grain growth induced by ELMs-like transient heat loads in deformed tungsten samples

Science.gov (United States)

Suslova, A.; El-Atwani, O.; Sagapuram, D.; Harilal, S. S.; Hassanein, A.

2014-11-01

Tungsten has been chosen as the main candidate for plasma facing components (PFCs) due to its superior properties under extreme operating conditions in future nuclear fusion reactors such as ITER. One of the serious issues for PFCs is the high heat load during transient events such as ELMs and disruption in the reactor. Recrystallization and grain size growth in PFC materials caused by transients are undesirable changes in the material, since the isotropic microstructure developed after recrystallization exhibits a higher ductile-to-brittle transition temperature which increases with the grain size, a lower thermal shock fatigue resistance, a lower mechanical strength, and an increased surface roughening. The current work was focused on careful determination of the threshold parameters for surface recrystallization, grain growth rate, and thermal shock fatigue resistance under ELM-like transient heat events. Transient heat loads were simulated using long pulse laser beams for two different grades of ultrafine-grained tungsten. It was observed that cold rolled tungsten demonstrated better power handling capabilities and higher thermal stress fatigue resistance compared to severely deformed tungsten. Higher recrystallization threshold, slower grain growth, and lower degree of surface roughening were observed in the cold rolled tungsten.

Interaction between recrystallization and strain-induced precipitation in a high Nb- and N-bearing austenitic stainless steel: Influence of the interpass time

Energy Technology Data Exchange (ETDEWEB)

Silva, M.B.R., E-mail: marianabdrs@gmail.com [Department of Materials Engineering, UFSCar, Via Washington Luis, Km 235, 13565-905 São Carlos, SP (Brazil); Gallego, J. [Department of Mechanical Engineering, UNESP, Avenida Brasil, 56, 15385-000 Ilha Solteira, SP (Brazil); Cabrera, J.M. [Department of Materials Science and Metallurgical Engineering, Polytechnic University of Catalunya, Avenida Diagonal 647, 08028 Barcelona (Spain); Fundacio CTM Centre Tecnologic, Plaza de la Ciencia 2, 08243 Manresa (Spain); Balancin, O. [Department of Materials Engineering, UFSCar, Via Washington Luis, Km 235, 13565-905 São Carlos, SP (Brazil); Jorge, A.M., E-mail: moreira@dema.ufscar.br [Department of Materials Engineering, UFSCar, Via Washington Luis, Km 235, 13565-905 São Carlos, SP (Brazil)

2015-06-18

In this work, we studied the influence of the interpass time (20 and 5 s) on the interaction between recrystallization and strain-induced precipitation occurring during multiple passes' deformations under continuous cooling conditions in a high niobium- and nitrogen-bearing austenitic stainless steel (ISO 5832-9). The correlation between microstructure evolution and hot mechanical properties was performed by physical simulation using hot torsion tests. The microstructure evolution was analyzed by optical microscopy, transmission electron microscopy and electron back scattered diffraction (EBSD). This technique indicated that dynamic recrystallization occurred at the first passes promoting an excellent grain refinement. On the other hand, shorter interpass time (5 s) allowed higher volume fraction of smallest precipitates than larger interpass time (20 s). After soaking, only TiNbN precipitates were found, whereas, Z-phase (CrNbN) and NbN were formed during thermomechanical processing. Particles with sizes between 20 and 50 nm were effective to pin grain boundaries and dislocations.

Microstructure and annealing behavior of a modified 9Cr-1Mo steel after dynamic plastic deformation to different strains

DEFF Research Database (Denmark)

Zhang, Zhenbo; Mishin, Oleg; Tao, N.R.

2015-01-01

The microstructure, hardness and tensile properties of a modified 9Cr-1Mo steel processed by dynamic plastic deformation (DPD) to different strains (0.5 and 2.3) have been investigated in the as-deformed and annealed conditions. It is found that significant structural refinement and a high level...... in a loss of strength with only a small gain in ductility, coarsening combined with pronounced partial recrystallization enables a combination of appreciably increased ductility and comparatively high strength....

The Microstructural Evolution and Special Flow Behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr During Isothermal Compression at a Low Strain Rate

Science.gov (United States)

Sun, J. Z.; Li, M. Q.; Li, H.

2017-09-01

The microstructural evolution and special flow behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr during isothermal compression at a strain rate of 0.0001 s-1 were investigated. The dislocation climbs in elongated α grains resulted in the formation of low-angle boundaries that transform into high-angle boundaries with greater deformation, and the elongated α grains subsequently separated into homogenous globular α grains with the penetration of the β phase. The simultaneous occurrence of discontinuous dynamic recrystallization and continuous dynamic recrystallization in the primary β grains resulted in a trimode grain distribution. The β grains surrounded by dislocations presented an equilateral-hexagonal morphology, which suggests that grain boundary sliding through dislocation climbs was the main deformation mechanism. The true stress-strain curves for 1073 and 1113 K abnormally intersect at a strain of 0.35, related to the α → β phase transformation and distinct growth of the β grain size.

Behavioral and neural Darwinism: selectionist function and mechanism in adaptive behavior dynamics.

Science.gov (United States)

McDowell, J J

2010-05-01

An evolutionary theory of behavior dynamics and a theory of neuronal group selection share a common selectionist framework. The theory of behavior dynamics instantiates abstractly the idea that behavior is selected by its consequences. It implements Darwinian principles of selection, reproduction, and mutation to generate adaptive behavior in virtual organisms. The behavior generated by the theory has been shown to be quantitatively indistinguishable from that of live organisms. The theory of neuronal group selection suggests a mechanism whereby the abstract principles of the evolutionary theory may be implemented in the nervous systems of biological organisms. According to this theory, groups of neurons subserving behavior may be selected by synaptic modifications that occur when the consequences of behavior activate value systems in the brain. Together, these theories constitute a framework for a comprehensive account of adaptive behavior that extends from brain function to the behavior of whole organisms in quantitative detail. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Hot Tensile and Fracture Behavior of 35CrMo Steel at Elevated Temperature and Strain Rate

Directory of Open Access Journals (Sweden)

Zhengbing Xiao

2016-08-01

Full Text Available To better understand the tensile deformation and fracture behavior of 35CrMo steel during hot processing, uniaxial tensile tests at elevated temperatures and strain rates were performed. Effects of deformation condition on the flow behavior, strain rate sensitivity, microstructure transformation, and fracture characteristic were characterized and discussed. The results indicated that the flow stress was sensitive to the deformation condition, and fracture occurs immediately after the peak stress level is reached, especially when the temperature is low or the strain rate is high. The strain rate sensitivity increases with the deformation temperature, which indicates that formability could improve at high temperatures. Photographs showing both the fracture surfaces and the matrix near the fracture section indicated the ductile nature of the material. However, the fracture mechanisms varied according to the deformation condition, which influences the dynamic recrystallization (DRX condition, and the DRX was accompanied by the formation of voids. For samples deformed at high temperatures or low strain rates, coalescence of numerous voids formed in the recrystallized grains is responsible for fracture, while at high strain rates or low temperatures, the grains rupture mainly by splitting because of cracks formed around the inclusions.

Whole through processing understanding of rolling and recrystallization textures in low carbon steels

International Nuclear Information System (INIS)

Roatta, A; Fourty, A; Bolmaro, R.E

2008-01-01

Processing steels to achieve particular useful properties is a science as well as an art. Many of the properties of modern steels are a successful combination of empiric and scientific knowledge. Deep drawing low carbon steels have been used and improved through many decades of research and technological advance. However the micro mechanisms involved in the development of particular microstructures and properties are still under discussion. The current paper shows an integrated attempt to obtain consistent microscopical data from micromechanical simulations coupled with recrystallization and phase transformation codes. The simulations are performed in a way such that the information obtained from certain temperature, level or process is used in the next step to proceed further. The goal is not avoiding experiments but having a whole through scale and time integration for judging the validity of similar parameters and assumptions during the different processing steps. The simulations include high and low temperature deformation and recrystallization in the austenite region, phase transformation to room temperature, low temperature deformation and recrystallization in the ferrite phase region. The results are compared with experiments available in the literature

Effect of controlling recrystallization from the melt on the residual stress and structural properties of the Silica-clad Ge core fiber

Science.gov (United States)

Zhao, Ziwen; Cheng, Xueli; He, Ting; Xue, Fei; Zhang, Wei; Chen, Na; Wen, Jianxiang; Zeng, Xianglong; Wang, Tingyun

2017-09-01

Effect of controlling recrystallization from the melt (1000 °C) on the residual stress and structural properties of a Ge core fiber via molten core drawing (MCD) method is investigated. Ge core fibers is investigated using Raman spectroscopy, scanning electron microscope (SEM), and X-ray diffraction (XRD). Compared with the as-drawn Ge fiber, the Raman peak of the recrystallized Ge fiber shift from 300 cm-1 to 300.6 cm-1 and full width at half maximum (FWHM) decreased from 5.36 cm-1 to 4.48 cm-1. The Ge crystal grains which sizes are of 200-600 nm were formed during the process of recrystallization; the XRD peak of (1 1 1) plane is observed after recrystallization. These results show that controlling recrystallization allows the release of the thermal stress, and improvement of the crystal quality of Ge core.

Nonlinear dynamics in human behavior

Energy Technology Data Exchange (ETDEWEB)

Huys, Raoul [Centre National de la Recherche Scientifique (CNRS), 13 - Marseille (France); Marseille Univ. (France). Movement Science Inst.; Jirsa, Viktor K. (eds.) [Centre National de la Recherche Scientifique (CNRS), 13 - Marseille (France); Marseille Univ. (France). Movement Science Inst.; Florida Atlantic Univ., Boca Raton, FL (United States). Center for Complex Systems and Brain Sciences

2010-07-01

Humans engage in a seemingly endless variety of different behaviors, of which some are found across species, while others are conceived of as typically human. Most generally, behavior comes about through the interplay of various constraints - informational, mechanical, neural, metabolic, and so on - operating at multiple scales in space and time. Over the years, consensus has grown in the research community that, rather than investigating behavior only from bottom up, it may be also well understood in terms of concepts and laws on the phenomenological level. Such top down approach is rooted in theories of synergetics and self-organization using tools from nonlinear dynamics. The present compendium brings together scientists from all over the world that have contributed to the development of their respective fields departing from this background. It provides an introduction to deterministic as well as stochastic dynamical systems and contains applications to motor control and coordination, visual perception and illusion, as well as auditory perception in the context of speech and music. (orig.)

Mechanical Behavior of Additively Manufactured Uranium-6 wt. pct. Niobium

Energy Technology Data Exchange (ETDEWEB)

Wu, A. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wraith, M. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Burke, S. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hamza, A. V. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brown, D. W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clausen, B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hsiung, L. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McKeown, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lindvall, R. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sedillo, E. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Teslich, N. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Torres, S. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Urabe, D. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Freeman, D. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alexander, P. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Iniguez, M. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ryerson, F. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ancheta, D. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lotscher, J. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Young, E. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Evans, C. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Florando, J. N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gallegos, G. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Margraff, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hrousis, C. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Campbell, G. H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-15

This report describes an effort to process uranium-6 weight% niobium using laser powder bed fusion. The chemistry, crystallography, microstructure and mechanical response resulting from this process are discussed with particular emphasis on the effect of the laser powder bed fusion process on impurities. In an effort to achieve homogenization and uniform mechanical behavior from different builds, as well as to induce a more conventional loading response, we explore post-processing heat treatments on this complex alloy. Elevated temperature heat treatment for recrystallization is evaluated and the effect of recrystallization on mechanical behavior in laser powder bed fusion processed U-6Nb is discussed. Wrought-like mechanical behavior and grain sizes are achieved through post-processing and are reported herein.

Deformation effect on recrystallization of Al-3.94 wt%Cu alloy

International Nuclear Information System (INIS)

Higgy, H.R.; Abou-El Nasr, T.Z.A.; Higgy, E.S.M.; Taha, A.M.S.

1981-01-01

The effect of cold-work and annealing temperature on the recrystallization of Al-3.94 wt%Cu was studied. As-received materials were annealed at both 400 0 C and 500 0 C before cold rolling. Cold-rolled specimens having 13%, 30%, 51% and 67% coldwork were isothermally annealed till 500 0 C, and then microscopically studied and hardness tested. Recrystallization process was found to be influenced by both deformation and annealing temperature. Grain-size increased with annealing temperature until 400 0 C, after which grain-size decreased. Cold-work decreased grain-size at all annealing temperatures. Hardness decreased with annealing temperature until 400 0 C, after which it increased sharply. Cold-work increased hardness, the increase was more pronounced at annealing temperatures below 400 0 C. (author)

Amorphization and recrystallization processes in monocrystalline beta silicon carbide thin films

International Nuclear Information System (INIS)

Edmond, J.A.; Withrow, S.P.; Kong, H.S.; Davis, R.F.

1985-01-01

Individual, as well as multiple doses of 27 Al + , 31 P + , 28 Si + , and 28 Si + and 12 C + , were implanted into (100) oriented monocrystalline β-SiC films. The critical energy of approx. =16 eV/atom required for the amorphization of β-SiC via implantation of 27 Al + and 31 P + was determined using the TRIM84 computer program for calculation of the damage-energy profiles coupled with the results of RBS/ion channeling analyses. In order to recrystallize amorphized layers created by the individual implantation of all four ion species, thermal annealing at 1600, 1700, or 1800 0 C was employed. Characterization of the recrystallized layers was performed using XTEM. Examples of SPE regrown layers containing precipitates and dislocation loops, highly faulted-microtwinned regions, and random crystallites were observed

A model for strain hardening, recovery, recrystallization and grain growth with applications to forming processes of nickel base alloys

Energy Technology Data Exchange (ETDEWEB)

Riedel, Hermann, E-mail: hermann.riedel@iwm.fraunhofer.de [Fraunhofer Institute for Materials Mechanics, Wöhlerstr. 11, 79108 Freiburg (Germany); Svoboda, Jiri, E-mail: svobj@ipm.cz [Institute of Physics of Materials, Academy of Science of the Czech Republic, Zizkova 22, Brno (Czech Republic)

2016-05-17

An ensemble of n spherical grains is considered, each of which is characterized by its radius r{sub i} and by a hardening variable a{sub i}. The hardening variable obeys a Chaboche-type evolution equation with dynamic and static recovery. The grain growth law includes the usual contribution of the grain boundary energy, a term for the stored energy associated with the hardening variable, and the Zener pinning force exerted by particles on the migrating grain boundaries. New grains develop by recrystallization in grains whose stored energy density exceeds a critical value. The growth or shrinkage of the particles, which restrain grain boundary migration, obeys a thermodynamic/kinetic evolution equation. This set of first order differential equations for r{sub i}, a{sub i} and the particle radius is integrated numerically. Fictitious model parameters for a virtual nickel base alloy are used to demonstrate the properties and capabilities of the model. For a real nickel alloy, model parameters are adjusted using measured stress-strain curves, as well as recrystallized volume fractions and grain size distributions. Finally the model with adjusted parameters is applied to a forming process with complex temperature-strain rate histories.

Prediction of Ductile Fracture Behaviors for 42CrMo Steel at Elevated Temperatures

Science.gov (United States)

Lin, Y. C.; Liu, Yan-Xing; Liu, Ge; Chen, Ming-Song; Huang, Yuan-Chun

2015-01-01

The ductile fracture behaviors of 42CrMo steel are studied by hot tensile tests with the deformation temperature range of 1123-1373 K and strain rate range of 0.0001-0.1 s-1. Effects of deformation temperature and strain rate on the flow stress and fracture strain of the studied steel are discussed in detail. Based on the experimental results, a ductile damage model is established to describe the combined effects of deformation temperature and strain rate on the ductile fracture behaviors of 42CrMo steel. It is found that the flow stress first increases to a peak value and then decreases, showing an obvious dynamic softening. This is mainly attributed to the dynamic recrystallization and material intrinsic damage during the hot tensile deformation. The established damage model is verified by hot forging experiments and finite element simulations. Comparisons between the predicted and experimental results indicate that the established ductile damage model is capable of predicting the fracture behaviors of 42CrMo steel during hot forging.

Oxide dispersion strengthened ferritic alloys. 14/20% chromium: effects of processing on deformation texture, recrystallization and tensile properties

International Nuclear Information System (INIS)

Regle, H.

1994-01-01

The ferritic oxide dispersion strengthened alloys are promising candidates for high temperature application materials, in particular for long life core components of advanced nuclear reactors. The aim of this work is to control the microstructure, in order to optimise the mechanical properties. The two ferritic alloys examined here, MA956 and MA957, are obtained by Mechanical Alloying techniques. They are characterised by quite anisotropic microstructure and mechanical properties. We have investigated the influence of hot and cold working processes (hot extrusion, swaging and cold-drawing) and recrystallization heat treatments on deformation textures, microstructures and tensile properties. The aim was to control the size of the grains and their anisotropic shape, using recrystallization heat treatments. After consolidation and hot extrusion, as-received materials present a extremely fine microstructure with elongated grains and a very strong (110) deformation texture with single-crystal character. At that stage of processing, recrystallization temperature are very high (1450 degrees C for MA957 alloy and 1350 degrees C for MA956 alloy) and materials develop millimetric recrystallized grains. Additional hot extrusion induce a fibre texture. Cold-drawing maintains a fibre texture, but the intensity decreases with increasing cold-work level. For both materials, the decrease of texture intensities correspond to a decrease of the recrystallization temperatures (from 1350 degrees C for a low cold-work level to 750 degrees C for 60 % cold-deformation, case of MA956 alloy) and a refinement of the grain size (from a millimetric size to less than an hundred of micrometer). Swaging develop a cyclic component where the intensity increases with increasing deformation in this case, the recrystallization temperature remains always very high and the millimetric grain size is slightly modified, even though cold-work level increases. Technologically, cold-drawing is the only way

Ice Recrystallization Inhibiting Polymers Enable Glycerol-Free Cryopreservation of Micro-organisms.

Science.gov (United States)

Hasan, Muhammad; Fayter, Alice E R; Gibson, Matthew I

2018-06-22

All modern molecular biology and microbiology is underpinned not only by the tools to handle and manipulate microorganisms, but also those to store, bank and transport them. Glycerol is the current gold-standard cryoprotectant but it is intrinsically toxic to most micro-organisms: only a fraction of cells survive freezing and the presence of glycerol can impact down-stream applications and assays. Extremophile organisms survive repeated freeze/thaw cycles by producing antifreeze proteins which are potent ice recrystallization inhibitors. Here we introduce a new concept for the storage/transport of micro-organisms by using ice recrystallization inhibiting poly(vinyl alcohol) in tandem with poly(ethylene glycol). This cryopreserving formulation is shown to result in a 4-fold increase in E. coli yield post-thaw, compared to glycerol, utilizing lower concentrations, with successful cryopreservation at just 1.1 weight percent of additive. The mechanism of protection is demonstrated to be linked to inhibiting ice recrystallization (by comparison to a recombinant antifreeze protein) but also to the significantly lower toxicity of the polymers compared to glycerol. Optimized formulations are presented and shown to be broadly applicable to the cryopreservation of a panel of Gram negative, Gram positive and Mycobacteria strains. This represents a step-change in how micro-organisms will be stored by the design of new macromolecular ice growth inhibitors; it should enable a transition from traditional solvent-based to macromolecular microbiology storage methods.

A quantitative evolutionary theory of adaptive behavior dynamics.

Science.gov (United States)

McDowell, J J

2013-10-01

The idea that behavior is selected by its consequences in a process analogous to organic evolution has been discussed for over 100 years. A recently proposed theory instantiates this idea by means of a genetic algorithm that operates on a population of potential behaviors. Behaviors in the population are represented by numbers in decimal integer (phenotypic) and binary bit string (genotypic) forms. One behavior from the population is emitted at random each time tick, after which a new population of potential behaviors is constructed by recombining parent behavior bit strings. If the emitted behavior produced a benefit to the organism, then parents are chosen on the basis of their phenotypic similarity to the emitted behavior; otherwise, they are chosen at random. After parent behavior recombination, the population is subjected to a small amount of mutation by flipping random bits in the population's bit strings. The behavior generated by this process of selection, reproduction, and mutation reaches equilibrium states that conform to every empirically valid equation of matching theory, exactly and without systematic error. These equations are known to describe the behavior of many vertebrate species, including humans, in a variety of experimental, naturalistic, natural, and social environments. The evolutionary theory also generates instantaneous dynamics and patterns of preference change in constantly changing environments that are consistent with the dynamics of live-organism behavior. These findings support the assertion that the world of behavior we observe and measure is generated by evolutionary dynamics. PsycINFO Database Record (c) 2013 APA, all rights reserved

Coupled disease-behavior dynamics on complex networks: A review

Science.gov (United States)

Wang, Zhen; Andrews, Michael A.; Wu, Zhi-Xi; Wang, Lin; Bauch, Chris T.

2015-12-01

It is increasingly recognized that a key component of successful infection control efforts is understanding the complex, two-way interaction between disease dynamics and human behavioral and social dynamics. Human behavior such as contact precautions and social distancing clearly influence disease prevalence, but disease prevalence can in turn alter human behavior, forming a coupled, nonlinear system. Moreover, in many cases, the spatial structure of the population cannot be ignored, such that social and behavioral processes and/or transmission of infection must be represented with complex networks. Research on studying coupled disease-behavior dynamics in complex networks in particular is growing rapidly, and frequently makes use of analysis methods and concepts from statistical physics. Here, we review some of the growing literature in this area. We contrast network-based approaches to homogeneous-mixing approaches, point out how their predictions differ, and describe the rich and often surprising behavior of disease-behavior dynamics on complex networks, and compare them to processes in statistical physics. We discuss how these models can capture the dynamics that characterize many real-world scenarios, thereby suggesting ways that policy makers can better design effective prevention strategies. We also describe the growing sources of digital data that are facilitating research in this area. Finally, we suggest pitfalls which might be faced by researchers in the field, and we suggest several ways in which the field could move forward in the coming years.

Effects of Static Recrystallization and Precipitation on Mechanical Properties of 00Cr12 Ferritic Stainless Steel

Science.gov (United States)

Shao, Yi; Liu, Chenxi; Yue, Tengxiao; Liu, Yongchang; Yan, Zesheng; Li, Huijun

2018-05-01

The 00Cr12 ferritic stainless steel samples were isothermally held at different temperatures in the range of 700 °C to 1000 °C to investigate the effect of static recrystallization and precipitation on mechanical properties, such as microhardness, tensile strength, and yield strength. The results show that the formation of the fine recrystallized grain, as well as precipitation, coarsening, and dissolution of the second-phase particles, influences the mechanical properties remarkably. The fine recrystallized grain can provide a positive grain boundary-strengthening effect in the sample under a relatively high holding temperature. Coarsening and dissolution of M23C6 result in partial depletion of precipitate hardening. In contrast, the size and number density of MX particles are almost constant, regardless of the holding temperature; therefore, it can provide a better precipitation-hardening effect.

Comparison studies of rheological and thermal behaviors of ionic liquids and nanoparticle ionic liquids.

Science.gov (United States)

Xu, Yiting; Zheng, Qiang; Song, Yihu

2015-08-14

Novel nanoparticle ionic liquids (NILs) are prepared by grafting modified nanoparticles with long-chain ionic liquids (ILs). The NIL behaves like a liquid at ambient temperature. We studied the rheological behavior of the IL and NIL over the range of 10-55 °C and found an extraordinary difference between the IL and NIL: a small content of nanosilica (7%) moderately improves the crystallinity by 7% of the poly(ethylene glycol) (PEG) segment in the IL, and it improves the dynamic moduli significantly (by 5 times at room temperature). It retards the decay temperature (by 10 °C) of the dynamic moduli during heating as well. The thermal rheological hysteresis observed during heating-cooling temperature sweeps is ascribed to the melting-recrystallization of the PEG segments. Meanwhile, the IL and NIL express accelerated crystallization behavior in comparison with the oligomeric anion. For the first time, we find that ILs and NILs are able to form nanoparticle-containing spherulites at room temperature after long time aging.

Modeling behavior dynamics using computational psychometrics within virtual worlds.

Science.gov (United States)

Cipresso, Pietro

2015-01-01

In case of fire in a building, how will people behave in the crowd? The behavior of each individual affects the behavior of others and, conversely, each one behaves considering the crowd as a whole and the individual others. In this article, I propose a three-step method to explore a brand new way to study behavior dynamics. The first step relies on the creation of specific situations with standard techniques (such as mental imagery, text, video, and audio) and an advanced technique [Virtual Reality (VR)] to manipulate experimental settings. The second step concerns the measurement of behavior in one, two, or many individuals focusing on parameters extractions to provide information about the behavior dynamics. Finally, the third step, which uses the parameters collected and measured in the previous two steps in order to simulate possible scenarios to forecast through computational models, understand, and explain behavior dynamics at the social level. An experimental study was also included to demonstrate the three-step method and a possible scenario.

Kinetics of thermal grooving during low temperature recrystallization of pure aluminum

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andy; Juul Jensen, Dorte

2013-01-01

The migration of a recrystallization boundary in pure aluminum was followed during in situ annealing in a scanning electron microscope. The microstructure was characterized using the electron channeling contrast technique, and a typical stop-go grain boundary motion was observed during annealing...

EBSD characterization of low temperature deformation mechanisms in modern alloys

Science.gov (United States)

Kozmel, Thomas S., II

For structural applications, grain refinement has been shown to enhance mechanical properties such as strength, fatigue resistance, and fracture toughness. Through control of the thermos-mechanical processing parameters, dynamic recrystallization mechanisms were used to produce microstructures consisting of sub-micron grains in 9310 steel, 4140 steel, and Ti-6Al-4V. In both 9310 and 4140 steel, the distribution of carbides throughout the microstructure affected the ability of the material to dynamically recrystallize and determined the size of the dynamically recrystallized grains. Processing the materials at lower temperatures and higher strain rates resulted in finer dynamically recrystallized grains. Microstructural process models that can be used to estimate the resulting microstructure based on the processing parameters were developed for both 9310 and 4140 steel. Heat treatment studies performed on 9310 steel showed that the sub-micron grain size obtained during deformation could not be retained due to the low equilibrium volume fraction of carbides. Commercially available aluminum alloys were investigated to explain their high strain rate deformation behavior. Alloys such as 2139, 2519, 5083, and 7039 exhibit strain softening after an ultimate strength is reached, followed by a rapid degradation of mechanical properties after a critical strain level has been reached. Microstructural analysis showed that the formation of shear bands typically preceded this rapid degradation in properties. Shear band boundary misorientations increased as a function of equivalent strain in all cases. Precipitation behavior was found to greatly influence the microstructural response of the alloys. Additionally, precipitation strengthened alloys were found to exhibit similar flow stress behavior, whereas solid solution strengthened alloys exhibited lower flow stresses but higher ductility during dynamic loading. Schmid factor maps demonstrated that shear band formation behavior

Recrystallized arrays of bismuth nanowires with trigonal orientation.

Science.gov (United States)

Limmer, Steven J; Yelton, W Graham; Erickson, Kristopher J; Medlin, Douglas L; Siegal, Michael P

2014-01-01

We demonstrate methods to improve the crystalline-quality of free-standing Bi nanowires arrays on a Si substrate and enhance the preferred trigonal orientation for thermoelectric performance by annealing the arrays above the 271.4 °C Bi melting point. The nanowires maintain their geometry during melting due to the formation of a thin Bi-oxide protective shell that contains the molten Bi. Recrystallizing nanowires from the melt improves crystallinity; those cooled rapidly demonstrate a strong trigonal orientation preference.

High heat load properties of nanostructured, recrystallized W–1.1TiC

Energy Technology Data Exchange (ETDEWEB)

Tokunaga, K., E-mail: tokunaga@riam.kyushu-u.ac.jp [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Kurishita, H.; Arakawa, H.; Matsuo, S. [International Research Center for Nuclear Materials Science, IMR, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Hotta, T. [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Araki, K.; Miyamoto, Y.; Fujiwara, T.; Nakamura, K. [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Takida, T.; Kato, M.; Ikegaya, A. [A.L.M.T. Corp., Toyama 931-8543 (Japan)

2013-11-15

Steady state (1973 K, 180 s) and repeated (723 K–1524 K, 380 times) heat loading experiments of ITER grade W and toughened, fine-grained, recrystallized W–1.1TiC (TFGR W–1.1TiC) have been performed using an electron beam irradiation system. In ITER grade W, the irradiation around 1973 K causes recrystallization and grain growth up to the average diameters of 50–100 μm. Repeated irradiations cause significant surface roughening, cracking at grain boundaries and surface exfoliation. On the other hand, TFGR W–1.1TiC does not exhibit any surface roughening or cracking after repeated heat loading although grain boundaries on the surface of TFGR W–1.1TiC can be observed after irradiation at around 1973 K 180 s by steady state heat loading.

Watching the growth of bulk grains during recrystallization of deformed metals

DEFF Research Database (Denmark)

Schmidt, Søren; Fæster Nielsen, Søren; Gundlach, C.

2004-01-01

, contradicting the classical assumption of smooth and spherical growth of new grains during recrystallization. This type of in situ bulk measurement opens up the possibility of obtaining experimental data on scientific topics that before could only be analyzed theoretically on the basis of the statistical...

Measurements of the Curvature of Protrusions/Retrusions on Migrating Recrystallization Boundaries

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, A.; Juul Jensen, Dorte

2009-01-01

Two methods to quantify protrusions/retrusions and to estimate local boundary curvature from sample plane sections are proposed. The methods are used to evaluate the driving force due to curvature of the protrusions/retrusions for partially recrystallized pure nickel cold rolled to 96% reduction...

Influence of phosphate glass recrystallization on the stability of a waste matrix to leaching

Science.gov (United States)

Yudintsev, S. V.; Pervukhina, A. M.; Mokhov, A. V.; Malkovsky, V. I.; Stefanovsky, S. V.

2017-04-01

In Russia, highly radioactive liquid wastes from recycling of spent fuel of nuclear reactors are solidified into Na-Al-P glass for underground storage. The properties of the matrix including the radionuclide fixation will change with time due to crystallization. This is supported by the results of study of the interaction between glassy matrices, products of their crystallization, and water. The concentration of Cs in a solution at the contact of a recrystallized sample increased by three orders of magnitude in comparison with an experiment with glass. This difference is nearly one order of magnitude for Sr, Ce, and Nd (simulators of actinides) and U due to their incorporation into phases with low solubility in water. Based on data on the compositional change of solutions after passing through filters of various diameters, it is concluded that Cs occurs in the dissolved state in runs with a glass and recrystallized matrix. At the same time, Sr, lanthanides, and U occur in the dissolved state and in the composition of colloids in runs with glass, and mostly in colloid particles after contact with the recrystallized sample. These results should be regarded for substantiation of safety for geological waste storage.

Influence of Extrusion Temperature on the Aging Behavior and Mechanical Properties of an AA6060 Aluminum Alloy

Directory of Open Access Journals (Sweden)

Nadja Berndt

2018-01-01

Full Text Available Processing of AA6060 aluminum alloys for semi-products usually includes hot extrusion with subsequent artificial aging for several hours. Processing below the recrystallization temperature allows for an increased strength at a significantly reduced annealing time by combining strain hardening and precipitation hardening. In this study, we investigate the potential of cold and warm extrusion as alternative processing routes for high strength aluminum semi-products. Cast billets of the age hardening aluminum alloy AA6060 were solution annealed and then extruded at room temperature, 120 or 170 °C, followed by an aging treatment. Electron microscopy and mechanical testing were performed on the as-extruded as well as the annealed materials to characterize the resulting microstructural features and mechanical properties. All of the extruded profiles exhibit similar, strongly graded microstructures. The strain gradients and the varying extrusion temperatures lead to different stages of dynamic precipitation in the as-extruded materials, which significantly alter the subsequent aging behavior and mechanical properties. The experimental results demonstrate that extrusion below recrystallization temperature allows for high strength at a massively reduced aging time due to dynamic precipitation and/or accelerated precipitation kinetics. The highest strength and ductility were achieved by extrusion at 120 °C and subsequent short-time aging.

Recrystallization of implanted amorphous silicon layers. I. Electrical properties of silicon implanted with BF+2 or Si++B+

International Nuclear Information System (INIS)

Tsai, M.Y.; Streetman, B.G.

1979-01-01

Electrical properties of recrystallized amorphous silicon layers, formed by BF + 2 implants or Si + +B + implants, have been studied by differential resistivity and Hall-effect measurements. Electrical carrier distribution profiles show that boron atoms inside the amorphized Si layers can be fully activated during recrystallization at 550 0 C. The mobility is also recovered. However, the tail of the B distribution, located inside a damaged region near the original amorphous-crystalline interface, remains inactive. This inactive tail has been observed for all samples implanted with BF + 2 . Only in a thicker amorphous layer, formed for example by Si + predamage implants, can the entire B profile be activated. The etch rate of amorphous silicon in HF and the effect of fluorine on the recrystallization rate are also reported

Modeling Behavior Dynamics using Computational Psychometrics within Virtual Worlds

Directory of Open Access Journals (Sweden)

Pietro eCipresso

2015-11-01

Full Text Available In case of fire in a building, how will people behave in the crowd? The behavior of each individual affects the behavior of others and, conversely, each one behaves considering the crowd as a whole and the individual others. In this article, I propose a three-step method to explore a brand new way to study behavior dynamics. The first step relies on the creation of specific situations with standard techniques (such as mental imagery, text, video and audio and an advanced technique (Virtual Reality to manipulate experimental settings. The second step concerns the measurement of behavior in one, two or many individuals focusing on parameters extractions to provide information about the behavior dynamics. Finally, the third step, which uses the parameters collected and measured in the previous two steps in order to simulate possible scenarios to forecast through computational models, understand and explain behavior dynamics at the social level. An experimental study was also included to demonstrate the three-step method and a possible scenario.

Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates

International Nuclear Information System (INIS)

Chekhonin, Paul; Beausir, Benoît; Scharnweber, Juliane; Oertel, Carl-Georg; Hausöl, Tina; Höppel, Heinz Werner; Brokmeier, Heinz-Günter; Skrotzki, Werner

2012-01-01

Aluminium laminates consisting of high-purity aluminium and commercially pure aluminium have been produced by accumulative roll bonding (ARB) at ambient temperature for up to 10 cycles. To study the microstructure and texture development of the high-purity aluminium layers with regard to the shrinking layer thickness during ARB, microstructure and texture investigations were carried out by electron backscatter diffraction and neutron and X-ray diffraction, respectively. While the commercially pure aluminium layers develop an ultrafine-grained microstructure, partial discontinuous recrystallization occurs in the high-purity layers. The texture of the high-purity layers mainly consists of Cube and “Tilted Cube” (tilted with respect to the transverse direction) components. The experimental results are discussed with respect to confined recrystallization in the ARB aluminium laminates.

Dynamic behaviors in directed networks

International Nuclear Information System (INIS)

Park, Sung Min; Kim, Beom Jun

2006-01-01

Motivated by the abundance of directed synaptic couplings in a real biological neuronal network, we investigate the synchronization behavior of the Hodgkin-Huxley model in a directed network. We start from the standard model of the Watts-Strogatz undirected network and then change undirected edges to directed arcs with a given probability, still preserving the connectivity of the network. A generalized clustering coefficient for directed networks is defined and used to investigate the interplay between the synchronization behavior and underlying structural properties of directed networks. We observe that the directedness of complex networks plays an important role in emerging dynamical behaviors, which is also confirmed by a numerical study of the sociological game theoretic voter model on directed networks

In-situ studies of the recrystallization process of CuInS2 thin films by energy dispersive X-ray diffraction

International Nuclear Information System (INIS)

Thomas, D.; Mainz, R.; Rodriguez-Alvarez, H.; Marsen, B.; Abou-Ras, D.; Klaus, M.; Genzel, Ch.; Schock, H.-W.

2011-01-01

Recrystallization processes during the sulfurization of CuInS 2 (CIS) thin films have been studied in-situ using energy dispersive X-ray diffraction (EDXRD) with synchrotron radiation. In order to observe the recrystallization isolated from other reactions occurring during film growth, Cu-poor, small grained CIS layers covered with CuS on top were heated in a vacuum chamber equipped with windows for synchrotron radiation in order to analyze the grain growth mechanism within the CIS layer. In-situ monitoring of the grain size based on diffraction line profile analysis of the CIS-112 reflection was utilized to interrupt the recrystallization process at different points. Ex-situ studies by electron backscatter diffraction (EBSD) and energy dispersive X-ray spectroscopy (EDX) performed on samples of intermediate recrystallization states reveal that during the heat treatment Cu and In interdiffuse inside the layer indicating the importance of the mobility of these two elements during CuInS 2 grain growth.

The dynamic behavior of the exohedral transition metal complexes ...

Indian Academy of Sciences (India)

NAIWRIT KARMODAK

Special Issue on THEORETICAL CHEMISTRY/CHEMICAL DYNAMICS. The dynamic behavior ... The ab initio molecular dynamic simulations were performed at. 1200 K to ... boron clusters and the nature of polyhedral boranes suggested that ...

Evaluating system behavior through Dynamic Master Logic Diagram (DMLD) modeling

International Nuclear Information System (INIS)

Hu, Y.-S.; Modarres, Mohammad

1999-01-01

In this paper, the Dynamic Master Logic Diagram (DMLD) is introduced for representing full-scale time-dependent behavior and uncertain behavior of complex physical systems. Conceptually, the DMLD allows one to decompose a complex system hierarchically to model and to represent: (1) partial success/failure of the system, (2) full-scale logical, physical and fuzzy connectivity relations, (3) probabilistic, resolutional or linguistic uncertainty, (4) multiple-state system dynamics, and (5) floating threshold and transition effects. To demonstrate the technique, examples of using DMLD to model, to diagnose and to control dynamic behavior of a system are presented. A DMLD-based expert system building tool, called Dynamic Reliability Expert System (DREXs), is introduced to automate the DMLD modeling process

Some aspects of animal behavior and community dynamics

Directory of Open Access Journals (Sweden)

Vikas Rai

2011-09-01

Full Text Available We simulate the dynamical behavior of a few two - dimensional predator - prey systems in two - dimensional parameter spaces to gain insight into how functional responses affect community dynamics. The insight gained helps us design three dimensional systems. We construct models for a few ecosystems with three species and study them using computer simulations. The models have been developed by linking food chains which have both kinds of predators: specialist as well as generalist. The linking functions are weakly non-linear. The three dimensional model ecosystems have sexually reproducing top - predators. We perform extensive simulations to figure out dynamics of dynamical possibilities caused by changes in animal behavior. The animals change the foraging strategies and behave differently in different environments. At the end of the paper, we examine how diseases can govern transitions in meandering of dynamical models in bounded volume of their phase spaces.

Analysis of High Temperature Deformed Structure and Dynamic Precipitation in W9Mo3Cr4V Steel

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

With TEM、SEM, various high-temperature deformed structures inW9Mo3Cr4V steel were investigated. The sub-structures，recrystallized nuclei, as well as the dynamic precipitation were also studied and analyzed. The relationship between recrystallized structures and dynamic precipitation was discussed. The results showed that the deformed structures in W9Mo3Cr4V steel are more complicated than those in low alloy steels. Because W9Mo3Cr4V steel is a high-speed steel, there are a large number of residual carbides on the matrix. Also, much dynamic precipitating carbides will precipitate during deformation at high temperature.

Electron backscatter diffraction study of deformation and recrystallization textures of individual phases in a cross-rolled duplex steel

Energy Technology Data Exchange (ETDEWEB)

Zaid, Md; Bhattacharjee, P.P., E-mail: pinakib@iith.ac.in

2014-10-15

The evolution of microstructure and texture during cross-rolling and annealing was investigated by electron backscatter diffraction in a ferritic–austenitic duplex stainless steel. For this purpose an alloy with nearly equal volume fraction of the two phases was deformed by multi-pass cross-rolling process up to 90% reduction in thickness. The rolling and transverse directions were mutually interchanged in each pass by rotating the sample by 90° around the normal direction. In order to avoid deformation induced phase transformation and dynamic strain aging, the rolling was carried out at an optimized temperature of 898 K (625 °C) at the warm-deformation range. The microstructure after cross warm-rolling revealed a lamellar structure with alternate arrangement of the bands of two phases. Strong brass and rotated brass components were observed in austenite in the steel after processing by cross warm-rolling. The ferrite in the cross warm-rolling processed steel showed remarkably strong RD-fiber (RD//< 011 >) component (001)< 011 >. The development of texture in the two phases after processing by cross warm-rolling could be explained by the stability of the texture components. During isothermal annealing of the 90% cross warm-rolling processed material the lamellar morphology was retained before collapse of the lamellar structure to the mutual interpenetration of the phase bands. Ferrite showed recovery resulting in annealing texture similar to the deformation texture. In contrast, the austenite showed primary recrystallization without preferential orientation selection leading to the retention of deformation texture. The evolution of deformation and annealing texture in the two phases of the steel was independent of one another. - Highlights: • Effect of cross warm-rolling on texture formation is studied in duplex steel. • Brass texture in austenite and (001)<110 > in ferrite are developed. • Ferrite shows recovery during annealing retaining the (001

Homogeneous nucleation, growth and recrystallization of discharge products on electrodes

Energy Technology Data Exchange (ETDEWEB)

Kappus, W.

1983-11-01

The early stage of discharge of electrodes with an electrodissolution/precipitation mechanism is investigated. A theory is proposed for quasi-classical homogeneous nucleation and the subsequent growth. Based on this theory the radii distribution function was calculated for the diffusion-controlled growth of crystallites. Recrystallization was included. The nucleation overpotential was calculated as a function of time for discharges under various conditions.

Dark field X-ray microscopy for studies of recrystallization

DEFF Research Database (Denmark)

Ahl, Sonja Rosenlund; Simons, Hugh; Jakobsen, Anders Clemen

2015-01-01

We present the recently developed technique of Dark Field X-Ray Microscopy that utilizes the diffraction of hard X-rays from individual grains or subgrains at the (sub)micrometre- scale embedded within mm-sized samples. By magnifying the diffracted signal, 3D mapping of orientations and strains...... external influences. The capabilities of Dark Field X- Ray Microscopy are illustrated by examples from an ongoing study of recrystallization of 50% cold-rolled Al1050 specimens....

X-ray and DSC studies on the melt-recrystallization process of poly(butylene naphthalate)

International Nuclear Information System (INIS)

Yasuniwa, Munehisa; Tsubakihara, Shinsuke; Fujioka, Takashi

2003-01-01

Melt-recrystallization in the heating process of poly(butylene naphthalate) (PBN) was studied with X-ray analysis and differential scanning calorimetry (DSC). DSC melting curve of an isothermally crystallized sample showed double endothermic peaks. With increasing the temperature, wide-angle X-ray diffraction (WAXD) patterns of the sample were obtained successively. Crystal structure did not change during the double melting process. The X-ray diffraction intensity decreased gradually in the temperature region up to about 200 deg. C, and then increased distinctly before steep decrease due to the final melting. This increase is interpreted as a proof of recrystallization. The temperature derivative curve of the diffraction intensity was similar to the DSC melting curve

Modeling detour behavior of pedestrian dynamics under different conditions

Science.gov (United States)

Qu, Yunchao; Xiao, Yao; Wu, Jianjun; Tang, Tao; Gao, Ziyou

2018-02-01

Pedestrian simulation approach has been widely used to reveal the human behavior and evaluate the performance of crowd evacuation. In the existing pedestrian simulation models, the social force model is capable of predicting many collective phenomena. Detour behavior occurs in many cases, and the important behavior is a dominate factor of the crowd evacuation efficiency. However, limited attention has been attracted for analyzing and modeling the characteristics of detour behavior. In this paper, a modified social force model integrated by Voronoi diagram is proposed to calculate the detour direction and preferred velocity. Besides, with the consideration of locations and velocities of neighbor pedestrians, a Logit-based choice model is built to describe the detour direction choice. The proposed model is applied to analyze pedestrian dynamics in a corridor scenario with either unidirectional or bidirectional flow, and a building scenario in real-world. Simulation results show that the modified social force model including detour behavior could reduce the frequency of collision and deadlock, increase the average speed of the crowd, and predict more practical crowd dynamics with detour behavior. This model can also be potentially applied to understand the pedestrian dynamics and design emergent management strategies for crowd evacuations.

Stress corrosion cracking behavior of zircaloy-2 in iodine environment

International Nuclear Information System (INIS)

Ikeda, Seiichi

1983-01-01

The effects of strain rates, iodine partial pressure and testing temperature on SCC behavior of zircaloy-2 in iodine environment were studied by means of slow strain rate technique (SSRT). SCC behavior of recrystallized specimens in iodine environment was remarkably influenced by the testing temperatures, and the susceptibility to SCC of specimens tested at 623 K was higher than that at 573 K. The susceptibility to SCC of recrystallized specimens increased with increasing iodine partial pressure at the lower strain rates of 4.2 x 10 -6 s -1 and 8.3 x 10 -7 s -1 . Cold worked specimens indicate no SCC failure in iodine environment regardless of strain rates, although those were tested only at 573 K. Fractographic observation revealed that SCC features of recrystallized specimens can be classified into two groups. One group, mostly specimens tested at 573 K, are characterized by the fact that cracks are initiated from corrosion pits. The other group are characterized by transgranuler SCC in the absence of pitting. This type of crack is found on specimens tested in environments containing more than 570 Pa iodine and seems to be produced by iodine embrittlement. (author)

Tensile behavior change depending on the microstructure of a Fe-Cu alloy produced from rapidly solidified powder

International Nuclear Information System (INIS)

Kakisawa, Hideki; Minagawa, Kazumi; Halada, Kohmei

2003-01-01

The relationship between consolidating temperature and the tensile behavior of iron alloy produced from Fe-Cu rapidly solidified powder is investigated. Fe-Cu powder fabricated by high-pressure water atomization was consolidated by heavy rolling at 873-1273 K. Microstructural changes were observed and tensile behavior was examined. Tensile behavior varies as the consolidating temperature changes, and these temperature-dependent differences depend on the morphology of the microstructure on the order of micrometers. The sample consolidated at 873 K shows a good strength/elongation balance because the powder microstructure and primary powder boundaries are maintained. The samples consolidated at the higher temperatures have a microstructure of recrystallized grains, and these recrystallized samples show the conventional relationship between tensile behavior and grain size in ordinal bulk materials

A quasi-in-situ EBSD observation of the transformation from rolling texture to recrystallization texture in V-4Cr-4Ti alloy

Energy Technology Data Exchange (ETDEWEB)

Peng, Lixia [Institute of Materials Research, China Academy of Engineering Physics, Jiangyou, Sichuan Province 621908 (China); Li, Xiongwei [Institute of Metal Research, China Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Fan, Zhijian [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan Province 621900 (China); Jiang, Chunli; Zhou, Ping [Institute of Materials Research, China Academy of Engineering Physics, Jiangyou, Sichuan Province 621908 (China); Lai, Xinchun, E-mail: laixinchun@caep.cn [Institute of Materials Research, China Academy of Engineering Physics, Jiangyou, Sichuan Province 621908 (China)

2017-04-15

Recrystallization texture evolution of rolled V-4Cr-4Ti alloy has been investigated by quasi-in-situ EBSD (electron back-scattering diffraction) method. Concurrently, the precipitates were characterized by SEM (Scanning Electron Microscopy). It was found that both the initial rolling textures and the distribution of the precipitates affected the formation of the recrystallization texture. It was revealed that the texture transformations of (558) 〈110〉 + (665) 〈110〉 to (334) 〈483〉 + (665) 〈1 1 2.4〉 were possibly attributed to the selective drag induced by the sparsely dispersed Ti-rich precipitates. While the densely distributed Ti-rich precipitates were responsible for the randomized recrystallization texture. Finally, when the precipitates were absent, the orientation changes from (112) 〈110〉 and (558) 〈110〉 to (111) 〈112〉 and (001) <110> to (001) <520> were observed. - Highlights: • Micro recrystallization texture evolution in V-4Cr-4Ti alloys is reported for the first time. • The volume fraction of Ti-rich precipitates has significant effect on the recrystallization texture evolution. • The dissolution of the Ti-rich precipitates above 1100 °C induces the strengthening of (111) <112> texture.

Steady State Dynamic Operating Behavior of Universal Motor

Directory of Open Access Journals (Sweden)

Muhammad Khan Burdi

2015-01-01

Full Text Available A detailed investigation of the universal motor is developed and used for various dynamic steady state and transient operating conditions of loads. In the investigation, output torque, motor speed, input current, input/output power and efficiency are computed, compared and analyzed for different loads. While this paper discusses the steady-state behavior of the universal motor, another companion paper, ?Transient dynamic behavior of universal motor?, will discuss its transient behavior in detail. A non-linear generalized electric machine model of the motor is considered for the analysis. This study was essential to investigate effect of output load on input current, power, speed and efficiency of the motor during operations. Previously such investigation is not known

Simulation of recrystallization textures in FCC materials based on a self consistent model

International Nuclear Information System (INIS)

Bolmaro, R.E; Roatta, A; Fourty, A.L; Signorelli, J.W; Bertinetti, M.A

2004-01-01

The development of re-crystallization textures in FCC polycrystalline materials has been a long lasting scientific problem. The appearance of the so-called cubic component in high stack fault energy laminated FCC materials is not an entirely understood phenomenon. This work approaches the problem using a self- consistent simulation technique of homogenization. The information on first preferential neighbors is used in the model to consider grain boundary energies and intra granular misorientations and to treat the growth of grains and the mobility of the grain boundary. The energies accumulated by deformations are taken as conducting energies of the nucleation and the later growth is statistically governed by the grain boundary energies. The model shows the correct trend for re-crystallization textures obtained from previously simulated deformation textures for high and low stack fault energy FCC materials. The model's topological representation is discussed (CW)

Assessing the Dynamic Behavior of Online Q&A Knowledge Markets: A System Dynamics Approach

Science.gov (United States)

Jafari, Mostafa; Hesamamiri, Roozbeh; Sadjadi, Jafar; Bourouni, Atieh

2012-01-01

Purpose: The objective of this paper is to propose a holistic dynamic model for understanding the behavior of a complex and internet-based kind of knowledge market by considering both social and economic interactions. Design/methodology/approach: A system dynamics (SD) model is formulated in this study to investigate the dynamic characteristics of…

Influence of human behavior on cholera dynamics.

Science.gov (United States)

Wang, Xueying; Gao, Daozhou; Wang, Jin

2015-09-01

This paper is devoted to studying the impact of human behavior on cholera infection. We start with a cholera ordinary differential equation (ODE) model that incorporates human behavior via modeling disease prevalence dependent contact rates for direct and indirect transmissions and infectious host shedding. Local and global dynamics of the model are analyzed with respect to the basic reproduction number. We then extend the ODE model to a reaction-convection-diffusion partial differential equation (PDE) model that accounts for the movement of both human hosts and bacteria. Particularly, we investigate the cholera spreading speed by analyzing the traveling wave solutions of the PDE model, and disease threshold dynamics by numerically evaluating the basic reproduction number of the PDE model. Our results show that human behavior can reduce (a) the endemic and epidemic levels, (b) cholera spreading speeds and (c) the risk of infection (characterized by the basic reproduction number). Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Hexagonal type Ising nanowire with mixed spins: Some dynamic behaviors

International Nuclear Information System (INIS)

Kantar, Ersin; Kocakaplan, Yusuf

2015-01-01

The dynamic behaviors of a mixed spin (1/2–1) hexagonal Ising nanowire (HIN) with core–shell structure in the presence of a time dependent magnetic field are investigated by using the effective-field theory with correlations based on the Glauber-type stochastic dynamics (DEFT). According to the values of interaction parameters, temperature dependence of the dynamic magnetizations, the hysteresis loop areas and the dynamic correlations are investigated to characterize the nature (first- or second-order) of the dynamic phase transitions (DPTs). Dynamic phase diagrams, including compensation points, are also obtained. Moreover, from the thermal variations of the dynamic total magnetization, the five compensation types can be found under certain conditions, namely the Q-, R-, S-, P-, and N-types. - Highlights: • Dynamic behaviors of mixed spin HIN system are obtained within the EFT. • The system exhibits i, p and nm fundamental phases. • The dynamic phase diagrams are presented in (h, T), (D, T), (Δ S , T) and (r, T) planes. • The dynamic phase diagrams exhibit the dynamic tricritical point (TCP). • Different dynamic compensation types are obtained

Thermal isocreep curves obtained during multi-axial creep tests on recrystallized Zircaloy-4 and M5™ alloy

International Nuclear Information System (INIS)

Rautenberg, M.; Poquillon, D.; Pilvin, P.; Grosjean, C.; Cloué, J.M.; Feaugas, X.

2014-01-01

Zirconium alloys are widely used in the nuclear industry. Several components, such as cladding or guide tubes, undergo strong mechanical loading during and after their use inside the pressurized water reactors. The current requirements on higher fuel performances lead to the developing on new Zr based alloys exhibiting better mechanical properties. In this framework, creep behaviors of recrystallized Zircaloy-4 and M5™, have been investigated and then compared. In order to give a better understanding of the thermal creep anisotropy of Zr-based alloys, multi-axial creep tests have been carried out at 673 K. Using a specific device, creep conditions have been set using different values of β = σ zz /σ θθ , σ zz and σ θθ being respectively the axial and hoop creep stresses. Both axial and hoop strains are measured during each test which is carried out until stationary creep is stabilized. The steady-state strain rates are then used to build isocreep curves. Considering the isocreep curves, the M5™ alloy shows a largely improved creep resistance compared to the recrystallized Zircaloy-4, especially for tubes under high hoop loadings (0 < β < 1). The isocreep curves are then compared with simulations performed using two different mechanical models. Model 1 uses a von Mises yield criterion, the model 2 is based on a Hill yield criterion. For both models, a coefficient derived from Norton law is used to assess the stress dependence

Texture, local misorientation, grain boundary and recrystallization fraction in pipeline steels related to hydrogen induced cracking

Energy Technology Data Exchange (ETDEWEB)

Mohtadi-Bonab, M.A., E-mail: m.mohtadi@usask.ca; Eskandari, M.; Szpunar, J.A.

2015-01-03

In the present study, API X60 and X60SS pipeline steels were cathodically charged by hydrogen for 8 h using 0.2 M sulfuric acid and 3 g/l ammonium thiocyanate. After charging, SEM observations showed that the hydrogen induced cracking (HIC) appeared at the center of cross section in the X60 specimen. However, HIC did not appear in the X60SS steel. Therefore, electron backscatter diffraction (EBSD) technique was used to analyze the center of cross section of as-received X60SS, X60 and HIC tested X60 specimens. The results showed that the HIC crack not only can propagate through 〈100〉||ND oriented grains but also its growth may happen in various orientations. In HIC tested X60 specimen, an accumulation of low angle grain boundaries around the crack path documented that full recrystallization was not achieved during hot rolling. Kernel Average Misorientaion (KAM) histogram illustrated that the deformation is more concentrated in as-received and HIC tested X60 specimens rather than in as-received X60SS specimen. Moreover, the concentration of coincidence site lattice (CSL) boundary in HIC tested X60 specimen was very low compared with other samples. The recrystallization area fraction in X60SS steel was very high. This high amount of recrystallization fraction with no stored energy is one of the main reasons for high HIC resistance of this steel to HIC. The orientation distribution function (ODF) of the recrystallized, substructured and deformed fractions in as-received X60SS and X60 steel showed relative close orientations in both as-received specimens.

Dynamic magnetic hysteresis behavior and dynamic phase transition in the spin-1 Blume-Capel model

Energy Technology Data Exchange (ETDEWEB)

Deviren, Bayram, E-mail: bayram.deviren@nevsehir.edu.tr [Department of Physics, Nevsehir University, 50300 Nevsehir (Turkey); Keskin, Mustafa [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)

2012-03-15

The nature (time variation) of response magnetization m(wt) of the spin-1 Blume-Capel model in the presence of a periodically varying external magnetic field h(wt) is studied by employing the effective-field theory (EFT) with correlations as well as the Glauber-type stochastic dynamics. We determine the time variations of m(wt) and h(wt) for various temperatures, and investigate the dynamic magnetic hysteresis behavior. We also investigate the temperature dependence of the dynamic magnetization, hysteresis loop area and correlation near the transition point in order to characterize the nature (first- or second-order) of the dynamic transitions as well as obtain the dynamic phase transition temperatures. The hysteresis loops are obtained for different reduced temperatures and we find that the areas of the loops are decreasing with the increasing of the reduced temperatures. We also present the dynamic phase diagrams and compare the results of the EFT with the results of the dynamic mean-field approximation. The phase diagrams exhibit many dynamic critical points, such as tricritical ( Bullet ), zero-temperature critical (Z), triple (TP) and multicritical (A) points. According to values of Hamiltonian parameters, besides the paramagnetic (P), ferromagnetic (F) fundamental phases, one coexistence or mixed phase region, (F+P) and the reentrant behavior exist in the system. The results are in good agreement with some experimental and theoretical results. - Highlights: Black-Right-Pointing-Pointer Kinetic spin-1 Blume-Capel model is studied using the effective-field theory. Black-Right-Pointing-Pointer We investigated the dynamic magnetic hysteresis behavior. Black-Right-Pointing-Pointer Dynamic magnetization, hysteresis loop area and correlation are investigated. Black-Right-Pointing-Pointer System exhibits tricritical, zero-temperature, triple and multicritical points. Black-Right-Pointing-Pointer We present the dynamic phase diagrams and compare the results of the EFT

A non-parametric hierarchical model to discover behavior dynamics from tracks

NARCIS (Netherlands)

Kooij, J.F.P.; Englebienne, G.; Gavrila, D.M.

2012-01-01

We present a novel non-parametric Bayesian model to jointly discover the dynamics of low-level actions and high-level behaviors of tracked people in open environments. Our model represents behaviors as Markov chains of actions which capture high-level temporal dynamics. Actions may be shared by

The dynamic and quasi-static mechanical response of three aluminum armor alloys: 5059, 5083 and 7039

Energy Technology Data Exchange (ETDEWEB)

Perez-Bergquist, Sara J., E-mail: sara.perezbergquist@gmail.com [Materials Science and Technology Division, Los Alamos National Laboratory, NM 87545 (United States); Gray, G.T.; Cerreta, Ellen K.; Trujillo, Carl P.; Perez-Bergquist, Alex [Materials Science and Technology Division, Los Alamos National Laboratory, NM 87545 (United States)

2011-11-15

Highlights: {yields} Aluminum alloys for use in armor applications. {yields} Mechanical response in dynamic and quasi-static regimes with temperature dependence. {yields} Shear localization with evidence of early stages of dynamic recrystallization. - Abstract: The mechanical response and microstructural evolution of aluminum alloys 5083, 5059 and 7039 was examined in compression and shear in both the quasi-static (0.001 s{sup -1}) and dynamic ({approx}2000 s{sup -1}) strain rate regimes. Electron Back Scattered Diffraction was utilized for detailed post-mortem analysis of the specimens following loading. The mechanical responses in shear were found to be strain-rate sensitive. At the slowest strain rates, all of the alloys had relatively large volumes of highly deformed material with 5083 and 5059 having the largest shear affected volumes. The dynamic strain rate test samples all formed highly compact shear localized volumes across the sheared zone with 7039 consistently displaying the narrowest shear regions. The morphology of these shear bands, along with the limited hardening during deformation, indicate a mechanism change at the higher strain rates. Higher resolution orientation image mapping has shown that between the three alloys there are varying degrees of crystallographic order within the shear bands. Transmission electron microscopy revealed various stages of dynamic recrystallization were present suggesting that while low strain rate deformation is controlled by dislocation multiplication and glide, high strain and strain-rate deformation is influenced in part due to mechanical recrystallization.

Characterization of strengthening mechanism and hot deformation behavior of powder metallurgy molybdenum

International Nuclear Information System (INIS)

Xiao, Meili; Li, Fuguo; Xie, Hangfang; Wang, Yufeng

2012-01-01

Highlights: → Dynamic recrystallization of powder metallurgy molybdenum occurs in the temperature region (1200-1450 o C). → The value of strain hardening index n decreases along with the temperature rising. → The value of strain-rate sensitivity exponent m increases slowly at first and achieves a peak value at 1350 o C. → Deformation strengthening is the main strengthening mechanism at low temperature. → Rheological strengthening becomes the primary strengthening mechanism at high temperature. -- Abstract: The high-temperature deformation behavior of powder metallurgy molybdenum has been investigated based on a series of isothermal hot compression tests, which were carried out on a Gleeble-1500 thermal mechanical simulator in a wide range of temperatures (900-1450 o C) and strain rates (0.01-10 s -1 ). Through the research on the experimental stress-strain curves, it reveals that dynamic recrystallization softening effect of powder metallurgy molybdenum occurs in the temperature range from 1200 o C to 1450 o C, in which the flow stress is significantly sensitive to temperature. In comparison with the value of strain hardening index n which decreases along with the temperature rising, the value of strain-rate sensitivity exponent m does not change obviously; however, it increases slowly with the increasing of temperature at first and achieves a peak value at 1350 o C. Furthermore, relying on the comparison of mean value of n and m, it is suggested that deformation strengthening is the main strengthening mechanism at low temperature while the rheological strengthening changes into the primary strengthening mechanism at high temperature.

Evolutionary Dynamics of Collective Behavior Selection and Drift: Flocking, Collapse, and Oscillation.

Science.gov (United States)

Tan, Shaolin; Wang, Yaonan; Chen, Yao; Wang, Zhen

2016-06-14

Behavioral choice is ubiquitous across a wide range of interactive decision-making processes and a myriad of scientific disciplines. With regard to this issue, one entitative problem is actually to understand how collective social behaviors form and evolve among populations when they face a variety of conflict alternatives. In this paper, a selection-drift dynamic model is formulated to characterize the behavior imitation and exploration processes in social populations. Based on the proposed framework, several typical behavior evolution patterns, including behavioral flocking, collapse, and oscillation, are reproduced with different kinds of behavior networks. Interestingly, for the selection-drift dynamics on homogeneous symmetric behavior networks, we unveil the phase transition from behavioral flocking to collapse and derive the bifurcation diagram of the evolutionary stable behaviors in social behavior evolution. While via analyzing the survival conditions of the best behavior on heterogeneous symmetric behavior networks, we propose a selection-drift mechanism to guarantee consensus at the optimal behavior. Moreover, when the selection-drift dynamics on asymmetric behavior networks is simulated, it is shown that breaking the symmetry in behavior networks can induce various behavioral oscillations. These obtained results may shed new insights into understanding, detecting, and further controlling how social norm and cultural trends evolve.

Initial Stages of Recrystallization in Aluminum of Commercial Purity

DEFF Research Database (Denmark)

Hansen, Niels; Bay, Bent

1979-01-01

In commercial aluminum with a purity of 99.4 pct, the formation and growth of recrystallization nuclei were studied by techniques such asin-situ annealing in a high voltage electron microscope, transmission electron microscopy and light microscopy. Sample parameters were the initial grain size (370...... by the FeAl3 particles present in the commercial aluminum as impurities. The nucleation temperatures determined by high voltage electron microscopy and transmission electron microscopy decrease markedly when the initial grain size is decreased both after 50 and 90 pct cold rolling; a less pronounced...

Model of the recrystallization mechanism of amorphous silicon layers created by ion implantation

International Nuclear Information System (INIS)

Drosd, R.M.

1979-11-01

The recrystallization behavior during annealing of thin films of amorphous (α) silicon, in contact with a single crystal silicon substrate (referred to as C), has been studied in the transmission electron microscope (TEM). The amorphous film is created during high dose phosphorus ion implantation at 100 keV. It was found that the crystal substrate orientation and the implantation temperature have dramatic effects on the recrystallizaton rate, and the defect microstructure produced during annealing. Specifically, (100) wafers implanted at 77 0 K contain only a low density of dislocation loops, but when the same wafer is implanted at room temperature the dislocation density is increased drastically. (111) wafers, when implanted at 77 0 K show a high density of microtwins, but as the implantation temperature is increased a gradual increase in the density of dislocation loops is observed along with a reduction of the microtwins. At an implantation temperature of about 100 0 C both orientations give an identical defect microstructure when annealed, which is a dense tangle of dislocations

Critical dynamics in population vaccinating behavior.

Science.gov (United States)

Pananos, A Demetri; Bury, Thomas M; Wang, Clara; Schonfeld, Justin; Mohanty, Sharada P; Nyhan, Brendan; Salathé, Marcel; Bauch, Chris T

2017-12-26

Vaccine refusal can lead to renewed outbreaks of previously eliminated diseases and even delay global eradication. Vaccinating decisions exemplify a complex, coupled system where vaccinating behavior and disease dynamics influence one another. Such systems often exhibit critical phenomena-special dynamics close to a tipping point leading to a new dynamical regime. For instance, critical slowing down (declining rate of recovery from small perturbations) may emerge as a tipping point is approached. Here, we collected and geocoded tweets about measles-mumps-rubella vaccine and classified their sentiment using machine-learning algorithms. We also extracted data on measles-related Google searches. We find critical slowing down in the data at the level of California and the United States in the years before and after the 2014-2015 Disneyland, California measles outbreak. Critical slowing down starts growing appreciably several years before the Disneyland outbreak as vaccine uptake declines and the population approaches the tipping point. However, due to the adaptive nature of coupled behavior-disease systems, the population responds to the outbreak by moving away from the tipping point, causing "critical speeding up" whereby resilience to perturbations increases. A mathematical model of measles transmission and vaccine sentiment predicts the same qualitative patterns in the neighborhood of a tipping point to greatly reduced vaccine uptake and large epidemics. These results support the hypothesis that population vaccinating behavior near the disease elimination threshold is a critical phenomenon. Developing new analytical tools to detect these patterns in digital social data might help us identify populations at heightened risk of widespread vaccine refusal. Copyright © 2017 the Author(s). Published by PNAS.

Study of a spur gear dynamic behavior in transient regime

Science.gov (United States)

Khabou, M. T.; Bouchaala, N.; Chaari, F.; Fakhfakh, T.; Haddar, M.

2011-11-01

In this paper the dynamic behavior of a single stage spur gear reducer in transient regime is studied. Dynamic response of the single stage spur gear reducer is investigated at different rotating velocities. First, gear excitation is induced by the motor torque and load variation in addition to the fluctuation of meshing stiffness due to the variation of input rotational speed. Then, the dynamic response is computed using the Newmark method. After that, a parameter study is made on spur gear powered in the first place by an electric motor and in the second place by four strokes four cylinders diesel engine. Dynamic responses come to confirm a significant influence of the transient regime on the dynamic behavior of a gear set, particularly in the case of engine acyclism condition.

Subgrain Rotation Behavior in Sn3.0Ag0.5Cu-Sn37Pb Solder Joints During Thermal Shock

Science.gov (United States)

Han, Jing; Tan, Shihai; Guo, Fu

2018-01-01

Ball grid array (BGA) samples were soldered on a printed circuit board with Sn37Pb solder paste to investigate the recrystallization induced by subgrain rotation during thermal shock. The composition of the solder balls was Sn3.0Ag0.5Cu-Sn37Pb, which comprised mixed solder joints. The BGA component was cross-sectioned before thermal shock. The microstructure and grain orientations were obtained by a scanning electron microscope equipped with an electron back-scattered diffraction system. Two mixed solder joints at corners of the BGA component were selected as the subjects. The results showed that recrystallization occurred at the corner of the solder joints after 200 thermal shock cycles. The recrystallized subgrains had various new grain orientations. The newly generated grain orientations were closely related to the initial grain orientations, which indicated that different subgrain rotation behaviors could occur in one mixed solder joint with the same initial grain orientation. When the misorientation angles were very small, the rotation axes were about Sn [100], [010] and [001], as shown by analyzing the misorientation angles and subgrain rotation axes, while the subgrain rotation behavior with large misorientation angles in the solder joints was much more complicated. As Pb was contained in the solder joints and the stress was concentrated on the corner of the mixed solder joints, concaves and cracks were formed. When the adjacent recrystallized subgrains were separated, and the process of the continuous recrystallization was limited.

Hot ductility behavior of boron microalloyed steels

International Nuclear Information System (INIS)

Lopez-Chipres, E.; Mejia, I.; Maldonado, C.; Bedolla-Jacuinde, A.; Cabrera, J.M.

2007-01-01

The current study analyses the influence of boron contents (between 29 and 105 ppm) on the hot ductility of boron microalloyed steels. For this purpose, hot tensile tests were carried out at different temperatures (700, 800, 900 and 1000 deg. C) at a constant true strain rate of 0.001 s -1 . In general, results revealed an improvement of the hot ductility of steels at increasing boron content. At 700, 900 and 1000 deg. C the ductility is higher than at 800 deg. C, where boron microalloyed steels exhibit a region of ductility loss (trough region). Likewise, dynamic recrystallization only occurred at 900 and 1000 deg. C. The fracture surfaces of the tested steels at temperatures giving the high temperature ductility regime show that the fracture mode is a result of ductile failure, whereas it is ductile-brittle failure in the trough region. Results are discussed in terms of dynamic recrystallization and boron segregation towards austenite grain boundaries, which may retard the formation of pro-eutectoid ferrite and increase grain boundary cohesion

The investigation of recrystallization developed in the largely undercooled Ni–3 at.% Sn alloy

International Nuclear Information System (INIS)

Chen, Q.; Chen, Z.; Liu, F.; Cui, R.X.; Liang, T.

2015-01-01

Highlights: • The grain refinement occurred at ΔT ⩾ 230 K. • Plastic deformation and recrystallization led to grain refinement. • Grain refinement was evidenced directly by TEM. • Misorientation and different plane spacing were detected by high-resolution TEM. - Abstract: Using the molten glass purification combined with the cycle superheating methods, a refined grain was achieved in undercooled Ni–3 at.% Sn alloy. The characteristics of microstructures and substructures of the refined grain were investigated by the classical nucleation theory, the dimensionless superheating model and the stress accumulation model. The grain refinement occurring inevitably at high undercooling (ΔT) was ascribed to the plastic deformation of dendrites and subsequent recrystallization, which were evidenced by the transmission electron microscopy (TEM) (e.g. different types of dislocations, defects and sub-grain boundaries) and high-resolution TEM (e.g. misorientation and different plane spacings)

Social Dynamics Management and Functional Behavioral Assessment

Science.gov (United States)

Lee, David L.

2018-01-01

Managing social dynamics is a critical aspect of creating a positive learning environment in classrooms. In this paper three key interrelated ideas, reinforcement, function, and motivating operations, are discussed with relation to managing social behavior.

Melt spin processing and recrystallization of REBa2Cu3O7-x

International Nuclear Information System (INIS)

Folkerts, T.J.; Kramer, M.J.; Dennis, K.W.; McCallum, R.W.

1992-01-01

This paper introduces a containerless melt-spin processing technique for REBa 2 Cu 3 O 7-x using pre-reacted oxide powders which are rapidly melted and subsequentially quenched in a controlled atmosphere. This results in flakes with typical dimensional of 3000 x 150 x 15μm 3 . Gd123 and Nd123 form nearly amorphous ribbons with only minor BaCu 2 O 2 when dropped in N 2 . Y123 contains Y 2 O 3 , but that the Ba-Cu-P phases present depend on the processing parameters. SEM and TEM studies show these phases are finely diapered; the typical grain size for Y 2 O 3 is 1-2μm, and for the Ba-Cu-O phases it is <0.5μm. Upon recrystallization from the amorphous ribbon, the Gd123 and Nd123 form field directly into the 123 phase while the recrystallization of the Y123 ribbons is less direct

Copper Refinement from Anode to Cathode and then to Wire Rod: Effects of Impurities on Recrystallization Kinetics and Wire Ductility.

Science.gov (United States)

Helbert, Anne-Laure; Moya, Alice; Jil, Tomas; Andrieux, Michel; Ignat, Michel; Brisset, François; Baudin, Thierry

2015-10-01

In this paper, the traceability of copper from the anode to the cathode and then the wire rod has been studied in terms of impurity content, microstructure, texture, recrystallization kinetics, and ductility. These characterizations were obtained based on secondary ion mass spectrometry, differential scanning calorimetry (DSC), X-ray diffraction, HV hardness, and electron backscattered diffraction. It is shown that the recrystallization was delayed by the total amount of impurities. From tensile tests performed on cold drawn and subsequently annealed wires for a given time, a simplified model has been developed to link tensile elongation to the chemical composition. This model allowed quantification of the contribution of some additional elements, present in small quantity, on the recrystallization kinetics. The proposed model adjusted for the cold-drawn wires was also validated on both the cathode and wire rod used for the study of traceability.

Dynamic hysteresis behaviors in the kinetic Ising system on triangular lattice

Science.gov (United States)

Kantar, Ersin; Ertaş, Mehmet

2018-04-01

We studied dynamic hysteresis behaviors of the spin-1 Blume-Capel (BC) model in a triangular lattice by means of the effective-field theory (EFT) with correlations and using Glauber-type stochastic dynamics. The effects of the exchange interaction (J), crystal field (D), temperature (T) and oscillating frequency (w) on the hysteresis behaviors of the BC model in a triangular lattice are investigated in detail. Results are compared with some other dynamic studies and quantitatively good agreement is found.

Empirical modeling of dynamic behaviors of pneumatic artificial muscle actuators.

Science.gov (United States)

Wickramatunge, Kanchana Crishan; Leephakpreeda, Thananchai

2013-11-01

Pneumatic Artificial Muscle (PAM) actuators yield muscle-like mechanical actuation with high force to weight ratio, soft and flexible structure, and adaptable compliance for rehabilitation and prosthetic appliances to the disabled as well as humanoid robots or machines. The present study is to develop empirical models of the PAM actuators, that is, a PAM coupled with pneumatic control valves, in order to describe their dynamic behaviors for practical control design and usage. Empirical modeling is an efficient approach to computer-based modeling with observations of real behaviors. Different characteristics of dynamic behaviors of each PAM actuator are due not only to the structures of the PAM actuators themselves, but also to the variations of their material properties in manufacturing processes. To overcome the difficulties, the proposed empirical models are experimentally derived from real physical behaviors of the PAM actuators, which are being implemented. In case studies, the simulated results with good agreement to experimental results, show that the proposed methodology can be applied to describe the dynamic behaviors of the real PAM actuators. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Non-destructive characterization of recrystallization kinetics using three-dimensional X-ray diffraction microscopy

DEFF Research Database (Denmark)

Lauridsen, E.M.; Schmidt, Søren; Fæster Nielsen, Søren

2006-01-01

Three-dimensional X-ray diffraction (3DXRD) is used to characterize the nucleation and early growth of individual bulk nuclei in situ during recrystallization of 92% cold-rolled copper. It is found that some cube nuclei, but not all, have a significantly faster initial growth than the average...

Analysis of Flow Behavior of an Nb-Ti Microalloyed Steel During Hot Deformation

Science.gov (United States)

Mohebbi, Mohammad Sadegh; Parsa, Mohammad Habibi; Rezayat, Mohammad; Orovčík, L'ubomír

2018-03-01

The hot flow behavior of an Nb-Ti microalloyed steel is investigated through hot compression test at various strain rates and temperatures. By the combination of dynamic recovery (DRV) and dynamic recrystallization (DRX) models, a phenomenological constitutive model is developed to derive the flow stress. The predefined activation energy of Q = 270 kJ/mol and the exponent of n = 5 are successfully set to derive critical stress at the onset of DRX and saturation stress of DRV as functions of the Zener-Hollomon parameter by the classical hyperbolic sine equation. The remaining parameters of the constitutive model are determined by fitting them to the experiments. Through substitution of a normalized strain in the DRV model and considering the interconnections between dependent parameters, a new model is developed. It is shown that, despite its fewer parameters, this model is in good agreement with the experiments. Accurate analyses of flow data along with microstructural analyses indicate that the dissolution of NbC precipitates and its consequent solid solution strengthening and retardation of DRX are responsible for the distinguished behaviors in the two temperature ranges between T employed for the present steel in the whole tested temperature ranges.

Deformation Behavior of a Coarse-Grained Mg-8Al-1.5Ca-0.2Sr Magnesium Alloy at Elevated Temperatures

Science.gov (United States)

Lou, Yan; Liu, Xiao

2018-02-01

The compression tests were carried out on a coarse-grained Mg-8Al-1.5Ca-0.2Sr magnesium alloy samples at temperatures from 300 to 450 °C and strain rates from 0.001 to 10 s-1. The flow stress curves were analyzed using the double-differentiation method, and double minima were detected on the flow curves. The first set of minima is shown to identify the critical strain for twinning, while the second set indicates the critical strain for the initiation of dynamic recrystallization (DRX). Twin variant selection was numerically identified by comprehensive analysis of the Schmid factors for different deformation modes and the accommodation strains imposed on neighboring grains. It was found that twinning is initiated before DRX. Dynamic recrystallization volume increases with strain rate at a given deformation temperature. At high strain rate, various twin variants are activated to accommodate deformation, leading to the formation of twin intersections and high DRX volume. Fully dynamic recrystallized structure can be obtained at both high and low strain rates due to the high mobility of the grain and twin boundaries at the temperature of 400 °C.

Modeling Temporal Behavior in Large Networks: A Dynamic Mixed-Membership Model

Energy Technology Data Exchange (ETDEWEB)

Rossi, R; Gallagher, B; Neville, J; Henderson, K

2011-11-11

Given a large time-evolving network, how can we model and characterize the temporal behaviors of individual nodes (and network states)? How can we model the behavioral transition patterns of nodes? We propose a temporal behavior model that captures the 'roles' of nodes in the graph and how they evolve over time. The proposed dynamic behavioral mixed-membership model (DBMM) is scalable, fully automatic (no user-defined parameters), non-parametric/data-driven (no specific functional form or parameterization), interpretable (identifies explainable patterns), and flexible (applicable to dynamic and streaming networks). Moreover, the interpretable behavioral roles are generalizable, computationally efficient, and natively supports attributes. We applied our model for (a) identifying patterns and trends of nodes and network states based on the temporal behavior, (b) predicting future structural changes, and (c) detecting unusual temporal behavior transitions. We use eight large real-world datasets from different time-evolving settings (dynamic and streaming). In particular, we model the evolving mixed-memberships and the corresponding behavioral transitions of Twitter, Facebook, IP-Traces, Email (University), Internet AS, Enron, Reality, and IMDB. The experiments demonstrate the scalability, flexibility, and effectiveness of our model for identifying interesting patterns, detecting unusual structural transitions, and predicting the future structural changes of the network and individual nodes.

Dynamic behavior of a social model for opinion formation

Science.gov (United States)

Bordogna, Clelia M.; Albano, Ezequiel V.

2007-12-01

The dynamic behavior of a social group influenced by both a strong leader and the mass media, which is modeled according to the social impact theory, is studied under two situations: (i) The strong leader changes his/her state of opinion periodically while the mass media are not considered. In this case, the leader is capable of driving the group between a dynamically ordered state with a weak leader-group coupling (high-frequency regime) and a dynamically disordered state where the group follows the opinion of the leader (low-frequency regime). (ii) The mass-media change periodically their message and have to compete with a strong leader that keeps his/her state of opinion unchanged. In this case, the mass media require an amplitude threshold in order to overcome the influence of the leader and drive the system into a dynamically disordered state. The dynamic behavior characteristic of the studied social opinion model shares many features of physical systems that are relevant in the fields of statistical mechanics and condensed matter.

The influence of multiscale heterogeneity on recrystallization in nickel processed by accumulative roll bonding

DEFF Research Database (Denmark)

Mishin, Oleg; Zhang, Yubin; Godfrey, A.

2017-01-01

Microscopic and sample-scale heterogeneities have been characterized in nickel processed by accumulative roll bonding (ARB) to a von Mises strain of 4.8, and their influence on recrystallization have been analyzed. The microscopic deformation heterogeneities in this material are mostly associated...

A single grain approach applied to modelling recrystallization kinetics in a single-phase metal

NARCIS (Netherlands)

Chen, S.P.; Zwaag, van der S.

2004-01-01

A comprehensive model for the recrystallization kinetics is proposed which incorporates both microstructure and the textural components in the deformed state. The model is based on the single-grain approach proposed previously. The influence of the as-deformed grain orientation, which affects the

Harsh parenting, child behavior problems, and the dynamic coupling of parents' and children's positive behaviors.

Science.gov (United States)

Lunkenheimer, Erika; Ram, Nilam; Skowron, Elizabeth A; Yin, Peifeng

2017-09-01

We examined self-reported maternal and paternal harsh parenting (HP) and its effect on the moment-to-moment dynamic coupling of maternal autonomy support and children's positive, autonomous behavior. This positive behavior coupling was measured via hidden Markov models as the likelihood of transitions into specific positive dyadic states in real time. We also examined whether positive behavior coupling, in turn, predicted later HP and child behavior problems. Children (N = 96; age = 3.5 years at Time 1) and mothers completed structured clean-up and puzzle tasks in the laboratory. Mothers' and fathers' HP was associated with children's being less likely to respond positively to maternal autonomy support; mothers' HP was also associated with mothers' being less likely to respond positively to children's autonomous behavior. When mothers responded to children's autonomous behavior with greater autonomy support, children showed fewer externalizing and internalizing problems over time and mothers showed less HP over time. These results were unique to the dynamic coupling of maternal autonomy support and children's autonomous behavior: The overall amount of these positive behaviors did not similarly predict reduced problems. Findings suggest that HP in the family system compromises the coregulation of positive behavior between mother and child and that improving mothers' and children's abilities to respond optimally to one another's autonomy-supportive behaviors may reduce HP and child behavior problems over time. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Radium uptake by recrystallized gypsum: an incorporation study

International Nuclear Information System (INIS)

Lestini, Leslie; Beaucaire, Catherine; Vercouter, Thomas; Descostes, Michael

2013-01-01

Batch experiments of 226 Ra uptake by recrystallized gypsum CaSO 4 .2H 2 O(s), monitored over 200 days, have shown that the published value for the distribution coefficient of 226 Ra between gypsum and an aqueous phase, 0.03 (Gnanapragasam and Lewis, 1995), is an upper limit. This suggests that this value needs to be confirmed. A solid solution between gypsum and radium sulfate (Ca,Ra)SO 4 .2H 2 O(s) cannot be considered per se, which is not surprising considering gypsum's high solubility product (lg Ks = -4.58) and the ionic radius of VIII Ra (1.48 A), when compared to that of VIII Ca (1.12 A). (authors)

In situ electron backscatter diffraction investigation of recrystallization in a copper wire.

Science.gov (United States)

Brisset, François; Helbert, Anne-Laure; Baudin, Thierry

2013-08-01

The microstructural evolution of a cold drawn copper wire (reduction area of 38%) during primary recrystallization and grain growth was observed in situ by electron backscatter diffraction. Two thermal treatments were performed, and successive scans were acquired on samples undergoing heating from ambient temperature to a steady state of 200°C or 215°C. During a third in situ annealing, the temperature was continuously increased up to 600°C. Nuclei were observed to grow at the expense of the deformed microstructure. This growth was enhanced by the high stored energy difference between the nuclei and their neighbors (driving energy in recrystallization) and by the presence of high-angle grain boundaries of high mobility. In the early stages of growth, the nuclei twin and the newly created orientations continue to grow to the detriment of the strained copper. At high temperatures, the disappearance of some twins was evidenced by the migration of the incoherent twin boundaries. Thermal grooving of grain boundaries is observed at these high temperatures and affects the high mobile boundaries but tends to preserve the twin boundaries of lower energy. Thus, grooving may contribute to the twin vanishing.

Study of Cd Te recrystallization by hydrated-CdCl_2 thermal treatment

International Nuclear Information System (INIS)

Hernandez V, C.; Albor A, M. L.; Galarza G, U.; Aguilar H, J. R.; Gonzalez T, M. A.; Flores M, J. M.; Jimenez O, D.

2017-01-01

Cd Te thin films solar cells are currently produced using a layer sequence of glass/FTO/CdS/Cd Te/metal contact (Cu/Ag), these films are deposited by two different techniques, chemical bath deposition (CBD) and close space vapour transport (CSVT). In order to reach reasonable conversion efficiencies, the device has to be thermally treated in a hydrated-CdCl_2 atmosphere. This study was carried out using X-ray diffraction (XRD), photoluminescence, Sem-EDS, four probe method and Sims profiling of Cd Te. These analyses confirm the presence of hydrated CdCl_2 and Cd Te phases on Cd Te surface and shown a good recrystallization morphology helping to the carriers mobility along the structure. Using the thermal treatment was possible to reduce the resistivity of Cd Te thin film; it is a result to the Cl migration along the Cd Te solar cell structure, reducing the defects between CdS and Cd Te thin films. A strong Cd Te thin film recrystallization was observed by the implementation of a hydrated-CdCl_2 treatment doing to this a good candidate to Cd Te solar cells process. (Author)

Structure/property (constitutive and dynamic strength/damage) characterization of additively manufactured 316L SS

Science.gov (United States)

Gray, G. T., III; Livescu, V.; Rigg, P. A.; Trujillo, C. P.; Cady, C. M.; Chen, S. R.; Carpenter, J. S.; Lienert, T. J.; Fensin, S.

2015-09-01

For additive manufacturing (AM), the certification and qualification paradigm needs to evolve as there exists no "ASTM-type" additive manufacturing certified process or AM-material produced specifications. Accordingly, utilization of AM materials to meet engineering applications requires quantification of the constitutive properties of these evolving materials in comparison to conventionally-manufactured metals and alloys. Cylinders of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS is detailed in both the as-built condition and following heat-treatments designed to obtain full recrystallization. The constitutive behavior as a function of strain rate and temperature is presented and compared to that of nominal annealed wrought 316L SS plate. The dynamic damage evolution and failure response of all three materials was probed using flyer-plate impact driven spallation experiments at a peak stress of 4.5 GPa to examine incipient spallation response. The spall strength of AM-produced 316L SS was found to be very similar for the peak shock stress studied to that of annealed wrought or AM-316L SS following recrystallization. The damage evolution as a function of microstructure was characterized using optical metallography.

The dynamics of behavior in modified dictator games.

Directory of Open Access Journals (Sweden)

Jeannette Brosig-Koch

Full Text Available We investigate the dynamics of individual pro-social behavior over time. The dynamics are tested by running the same experiment with the same subjects at several points in time. To exclude learning and reputation building, we employ non-strategic decision tasks and a sequential prisoners-dilemma as a control treatment. In the first wave, pro-social concerns explain a high share of individual decisions. Pro-social decisions decrease over time, however. In the final wave, most decisions can be accounted for by assuming pure selfishness. Stable behavior in the sense that subjects stick to their decisions over time is observed predominantly for purely selfish subjects. We offer two explanation for our results: diminishing experimenter demand effects and moral self-licensing.

A Dynamic Object Behavior Model and Implementation Based on Computational Reflection

Institute of Scientific and Technical Information of China (English)

HE Cheng-wan; HE Fei; HE Ke-qing

2005-01-01

A dynamic object behavior model based on computational reflection is proposed. This model consists of function level and meta level, the meta objects in meta level manage the base objects and behaviors in function level, including dynamic binding and unbinding of base object and behavior.We implement this model with RoleJava Language, which is our self linguistic extension of the Java Language. Meta Objects are generated automatically at compile-time, this makes the reflecton mechanism transparent to programmers. Finally an example applying this model to a banking system is presented.

Hot Deformation Behavior of SiCP/A1-Cu Composite

Directory of Open Access Journals (Sweden)

CHENG Ming-yang

2017-02-01

Full Text Available Using the Gleeble-1500D simulator, the high temperature plastic deformation behavior of SiCp/Al-Cu composite were investigated at 350-500℃ with the strain rate of 0.01-10s-1. The true stress-strain curves were obtained in the tests. Constitutive equation and processing map were established. The results show that the softening mechanism of dynamic recrystallization is a feature of high-temperature flow stress-strain curves of SiCp/A1-Cu composite, and the peak stress increases with the decrease of deformation temperature or the increase of strain rate.The flow stress behavior of the composite during hot compression deformation can be represented by a Zener-Hollomon parameter in the hyperbolic sine form. Its activation energy for hot deformation Q is 320.79kJ/mol. The stable regions and the instability regions in the processing map were identified and the microstructures in different regions of processing map were studied.There are particle breakage and void in the instability regions.

Hot Deformation Behavior and a Two-Stage Constitutive Model of 20Mn5 Solid Steel Ingot during Hot Compression

Directory of Open Access Journals (Sweden)

Min Liu

2018-03-01

Full Text Available 20Mn5 steel is widely used in the manufacture of heavy hydro-generator shaft forging due to its strength, toughness, and wear resistance. However, the hot deformation and recrystallization behaviors of 20Mn5 steel compressed under a high temperature were not studied. For this article, hot compression experiments under temperatures of 850–1200 °C and strain rates of 0.01 s−1–1 s−1 were conducted using a Gleeble-1500D thermo-mechanical simulator. Flow stress-strain curves and microstructure after hot compression were obtained. Effects of temperature and strain rate on microstructure are analyzed. Based on the classical stress-dislocation relationship and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of 20Mn5 steel. Comparisons between experimental flow stress and predicted flow stress show that the predicted flow stress values are in good agreement with the experimental flow stress values, which indicates that the proposed constitutive model is reliable and can be used for numerical simulation of hot forging of 20Mn5 solid steel ingot.

Hot flow behavior of boron microalloyed steels

International Nuclear Information System (INIS)

Lopez-Chipres, E.; Mejia, I.; Maldonado, C.; Bedolla-Jacuinde, A.; El-Wahabi, M.; Cabrera, J.M.

2008-01-01

This research work studies the effect of boron contents on the hot flow behavior of boron microalloyed steels. For this purpose, uniaxial hot-compression tests were carried out in a low carbon steel microalloyed with four different amounts of boron over a wide range of temperatures (950, 1000, 1050 and 1100 deg. C) and constant true strain rates (10 -3 , 10 -2 and 10 -1 s -1 ). Experimental results revealed that both peak stress and peak strain tend to decrease as boron content increases, which indicates that boron additions have a solid solution softening effect. Likewise, the flow curves show a delaying effect on the kinetics of dynamic recrystallization (DRX) when increasing boron content. Deformed microstructures show a finer austenitic grain size in the steel with higher boron content (grain refinement effect). Results are discussed in terms of boron segregation towards austenitic grain boundaries during plastic deformation, which increases the movement of dislocations, enhances the grain boundary cohesion and modificates the grain boundary structure

On the dynamic behavior of mineralized tissues

Science.gov (United States)

Kulin, Robb Michael

Mineralized tissues, such as bone and antler, are complex hierarchical materials that have adapted over millennia to optimize strength and fracture resistance for their in vivo applications. As a structural support, skeletal bone primarily acts as a rigid framework that is resistant to fracture, and able to repair damage and adapt to sustained loads during its lifetime. Antler is typically deciduous and subjected to large bending moments and violent impacts during its annual cycle. To date, extensive characterization of the quasi-static mechanical properties of these materials has been performed. However, very little has been done to characterize their dynamic properties, despite the fact that the majority of failures in these materials occur under impact loads. Here, an in depth analysis of the dynamic mechanical behavior of these two materials is presented, using equine bone obtained post-mortem from donors ranging in age from 6 months to 28 years, and antler from the North American Elk. Specimens were tested under compressive strain rates of 10-3, 100, and 103 sec-1 in order to investigate their strain rate dependent compressive response. Fracture toughness experiments were performed using a four-point bending geometry on single and double-notch specimens in order to measure fracture toughness, as well as observe differences in crack propagation between dynamic (˜2x105 MPa˙m1/2/s) and quasi-static (˜0.25 MPa˙m1/2/s) loading rates. After testing, specimens were analyzed using a combination of optical, electron and confocal microscopy. Results indicated that the mechanical response of these materials is highly dependent on loading rate. Decreasing quasi-static fracture toughness is observed with age in bone specimens, while dynamic specimens show no age trends, yet universally decreased fracture toughness compared to those tested quasi-statically. For the first time, rising R-curve behavior in bone was also shown to exist under both quasi-static and dynamic

Exponential spreading and singular behavior of quantum dynamics near hyperbolic points.

Science.gov (United States)

Iomin, A

2013-05-01

Quantum dynamics of a particle in the vicinity of a hyperbolic point is considered. Expectation values of dynamical variables are calculated, and the singular behavior is analyzed. Exponentially fast extension of quantum dynamics is obtained, and conditions for this realization are analyzed.

Chapter 2. Experimental testing methods of materials under hot working conditions

International Nuclear Information System (INIS)

Rossard, C.

1976-01-01

The deformation under hot working conditions is defined and the purpose of laboratory tests is explained: strength, structure, hot-workability. The concepts of generalized stress strain and strain rate are introduced. These concepts find an interesting application in the equivalence principle. The different testing methods (tension, compression, torsion) and their possibilities are reviewed. The softening mechanisms are recalled: dynamic recovery and recrystallization, static and post-dynamic recrystallization. To explain the possibilities of simulation tests in hot working conditions, some examples are given: the evaluation of the stress-strain relationship (effect of the mechanical and thermal history); the determination of structural behavior (quenching, controled cooling law, decomposition kinetics) [fr

behaviorism: a framework for dynamic data visualization.

Science.gov (United States)

Forbes, Angus Graeme; Höllerer, Tobias; Legrady, George

2010-01-01

While a number of information visualization software frameworks exist, creating new visualizations, especially those that involve novel visualization metaphors, interaction techniques, data analysis strategies, and specialized rendering algorithms, is still often a difficult process. To facilitate the creation of novel visualizations we present a new software framework, behaviorism, which provides a wide range of flexibility when working with dynamic information on visual, temporal, and ontological levels, but at the same time providing appropriate abstractions which allow developers to create prototypes quickly which can then easily be turned into robust systems. The core of the framework is a set of three interconnected graphs, each with associated operators: a scene graph for high-performance 3D rendering, a data graph for different layers of semantically linked heterogeneous data, and a timing graph for sophisticated control of scheduling, interaction, and animation. In particular, the timing graph provides a unified system to add behaviors to both data and visual elements, as well as to the behaviors themselves. To evaluate the framework we look briefly at three different projects all of which required novel visualizations in different domains, and all of which worked with dynamic data in different ways: an interactive ecological simulation, an information art installation, and an information visualization technique.

Microstructural descriptors and cellular automata simulation of the effects of non-random nuclei location on recrystallization in two dimensions

Directory of Open Access Journals (Sweden)

Paulo Rangel Rios

2006-06-01

Full Text Available The effect of non-random nuclei location and the efficiency of microstructural descriptors in assessing such a situation are studied. Cellular automata simulation of recrystallization in two dimensions is carried out to simulate microstrutural evolution for nuclei distribution ranging from a periodic arrangement to clusters of nuclei. The simulation results are compared in detail with microstrutural descriptors normally used to follow transformation evolution. It is shown that the contiguity is particularly relevant to detect microstructural deviations from randomness. This work focuses on recrystallization but its results are applicable to any nucleation and growth transformation.

Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: Is grain boundary engineering achieved through recrystallization or grain growth?

International Nuclear Information System (INIS)

Bai, Qin; Zhao, Qing; Xia, Shuang; Wang, Baoshun; Zhou, Bangxin; Su, Cheng

2017-01-01

Grain boundary engineering (GBE) of nickel-based alloy 825 tubes was carried out with different cold drawing deformations by using a draw-bench on a factory production line and subsequent annealing at various temperatures. The microstructure evolution of alloy 825 during thermal-mechanical processing (TMP) was characterized by means of the electron backscatter diffraction (EBSD) technique to study the TMP effects on the grain boundary network and the evolution of grain boundary character distributions during high temperature annealing. The results showed that the proportion of ∑ 3 n coincidence site lattice (CSL) boundaries of alloy 825 tubes could be increased to > 75% by the TMP of 5% cold drawing and subsequent annealing at 1050 °C for 10 min. The microstructures of the partially recrystallized samples and the fully recrystallized samples suggested that the proportion of low ∑ CSL grain boundaries depended on the annealing time. The frequency of low ∑ CSL grain boundaries increases rapidly with increasing annealing time associating with the formation of large-size highly-twinned grains-cluster microstructure during recrystallization. However, upon further increasing annealing time, the frequency of low ∑ CSL grain boundaries decreased markedly during grain growth. So it is concluded that grain boundary engineering is achieved through recrystallization rather than grain growth. - Highlights: •The grain boundary engineering (GBE) is applicable to 825 tubes. •GBE is achieved through recrystallization rather than grain growth. •The low ∑ CSL grain boundaries in 825 tubes can be increased to > 75%.

Influence of recrystallization on thermal shock resistance of various tungsten grades

International Nuclear Information System (INIS)

Uytdenhouwen, I.; Decreton, M.; Hirai, T.; Linke, J.; Pintsuk, G.; Oost, G. van

2007-01-01

Thermal shock resistance of various tungsten grades (different manufacturing technologies and heat treatments) was examined under plasma disruption conditions, especially in the cracking regime, i.e. below the melting threshold. The tests have been simulated with the electron beam test facility JUDITH. The comparison of the thermal shock resistance showed that sintered tungsten appeared to be better than the deformed tungsten material and clear degradation after recrystallization was found. Damage processes linked to the mechanical properties of W are discussed

Information Processing Features Can Detect Behavioral Regimes of Dynamical Systems

Directory of Open Access Journals (Sweden)

Rick Quax

2018-01-01

Full Text Available In dynamical systems, local interactions between dynamical units generate correlations which are stored and transmitted throughout the system, generating the macroscopic behavior. However a framework to quantify exactly how these correlations are stored, transmitted, and combined at the microscopic scale is missing. Here we propose to characterize the notion of “information processing” based on all possible Shannon mutual information quantities between a future state and all possible sets of initial states. We apply it to the 256 elementary cellular automata (ECA, which are the simplest possible dynamical systems exhibiting behaviors ranging from simple to complex. Our main finding is that only a few information features are needed for full predictability of the systemic behavior and that the “information synergy” feature is always most predictive. Finally we apply the idea to foreign exchange (FX and interest-rate swap (IRS time-series data. We find an effective “slowing down” leading indicator in all three markets for the 2008 financial crisis when applied to the information features, as opposed to using the data itself directly. Our work suggests that the proposed characterization of the local information processing of units may be a promising direction for predicting emergent systemic behaviors.

[Comporison Sduty of Microstructure by Metallographicalk on the Polarized Light and Texture by XRD of CC 5083 and CC 5182 Aluminium Alloy after Cold Rolling and Recrystallization].

Science.gov (United States)

Chen, Ming-biao; Li, Yong-wei; Tan, Yuan-biao; Ma, Min; Wang, Xue-min; Liu, Wen-chang

2015-03-01

At present the study of relation between microstructure, texture and performance of CC 5083 aluminium alloy after cold tolling and recrystallization processes is still finitude. So that the use of the CC 5083 aluminium alloy be influenced. Be cased into electrical furnace, hot up with unlimited speed followed the furnace hot up to different temperature and annealed 2h respectively, and be cased into salt-beth furnace, hot up quickly to different temperature and annealed 30 min respectively for CC 5083 and CC 5182 aluminum alloy after cold roling with 91.5% reduction. The microstructure be watched use metallographic microscope, the texture be inspected by XRD. The start temperature of recrystallization and grain grow up temperature within annealing in the electric furnace of CC 5083 aluminum alloy board is 343 degrees C, and the shap of grain after grow up with long strip (the innovation point ); The start temperature of recrystallization within annealling in the salt bath furnace of CC 5083 is 343 degrees C. The start temperature and end temperature of recrystallization within annealling of CC 5083 and CC 5182 aluminum alloy is 371 degrees C. The grain grow up outstanding of cold rooled CC 5152 aluminum alloy after annealed with 454 degrees C in the electric furnace and salt bath furnace. The start temperature of grain grow up of CC 5083 alluminurn alloy annealed in the electric furnace and salt bath furnace respectively is higher than the start temperature of grain grow up of CC 5182 alluminum alloy annealed in the electric furnace and salt bath furnace respectively. The strat temperature of recrystallization grain grow up is higher than which annealled with other three manner annealing process. The recrystallization temperature of CC 5182 annealed in the salt bath furnace is higher than which annealed in the electric furnace. The recrystallization temperature of the surface layer of CC 5083 and CC 5182 aluminum alloy is higher than the inner layer (the innovation

The dynamic behavior of mortar under impact-loading

Science.gov (United States)

Kawai, Nobuaki; Inoue, Kenji; Misawa, Satoshi; Tanaka, Kyoji; Hayashi, Shizuo; Kondo, Ken-Ichi; Riedel, Werner

2007-06-01

Concrete and mortar are the most fundamental structural material. Therefore, considerable interest in characterizing the dynamic behavior of them under impact-loading exists. In this study, plate impact experiments have been performed to determine the dynamic behavior of mortar. Longitudinal and lateral stresses have been directly measured by means of embedded polyvinylidene fluoride (PVDF) gauges up to 1 GPa. A 200 mm-cal. powder gun enable us to measure longitudinal and lateral stresses at several point from the impact surface, simultaneously. The shear strength under impact-loading has been obtained from measured longitudinal and lateral stresses. The longitudinal stress profile shows a two-wave structure. It is indicated that this structure is associated with the onset of pore compaction and failure of mortar by comparing with hydrocode simulations using an elastic-plastic damage model for concrete.

Hole Defects Affect the Dynamic Fracture Behavior of Nearby Running Cracks

Directory of Open Access Journals (Sweden)

R. S. Yang

2018-01-01

Full Text Available Effects of defects on the dynamic fracture behavior of engineering materials cannot be neglected. Using the experimental system of digital laser dynamic caustics, the effects of defects on the dynamic fracture behavior of nearby running cracks are studied. When running cracks propagate near to defects, the crack path deflects toward the defect; the degree of deflection is greater for larger defect diameters. When the running crack propagates away from the defect, the degree of deflection gradually reduces and the original crack path is restored. The intersection between the caustic spot and the defect is the direct cause of the running crack deflection; the intersection area determines the degree of deflection. In addition, the defect locally inhibits the dynamic stress intensity factor of running cracks when they propagate toward the defect and locally promotes the dynamic stress intensity factor of running cracks when they propagate away from the defect.

Chaotic Dynamics of Cage Behavior in a High-Speed Cylindrical Roller Bearing

Directory of Open Access Journals (Sweden)

Long Chen

2016-01-01

Full Text Available This paper presents a mathematical model to investigate the nonlinear dynamic behavior of cage in high-speed cylindrical bearing. Variations of cage behavior due to varying cage eccentricity and cage guidance gap are observed. Hydrodynamic behavior in cage contacts is taken into consideration for a more realistic calculation of acting forces owing to high working speed. Analysis of real-time cage dynamic behavior on radial plane is carried out using chaos theory based on the theoretical and mathematical model established in the paper. The analytical results of this paper provide a solid foundation for designing and manufacturing of high-speed cylindrical roller bearing.

Study of Cd Te recrystallization by hydrated-CdCl{sub 2} thermal treatment

Energy Technology Data Exchange (ETDEWEB)

Hernandez V, C.; Albor A, M. L.; Galarza G, U.; Aguilar H, J. R. [IPN, Escuela Superior de Fisica y Matematicas, Departamento de Fisica, San Pedro Zacatenco, 07738 Ciudad de Mexico (Mexico); Gonzalez T, M. A. [IPN, Escuela Superior de Computo, Nueva Industrial Vallejo, 07738 Ciudad de Mexico (Mexico); Flores M, J. M. [IPN, Escuela Superior de Ingenieria Quimica e Industrias Extractivas, Departamento de Ingenieria en Metalurgia y Materiales, Nueva Industrial Vallejo, 07738 Ciudad de Mexico (Mexico); Jimenez O, D. [IPN, Escuela Superior de Ingenieria Mecanica y Electrica, SEPI, Nueva Industrial Vallejo, 07738 Ciudad de Mexico (Mexico)

2017-11-01

Cd Te thin films solar cells are currently produced using a layer sequence of glass/FTO/CdS/Cd Te/metal contact (Cu/Ag), these films are deposited by two different techniques, chemical bath deposition (CBD) and close space vapour transport (CSVT). In order to reach reasonable conversion efficiencies, the device has to be thermally treated in a hydrated-CdCl{sub 2} atmosphere. This study was carried out using X-ray diffraction (XRD), photoluminescence, Sem-EDS, four probe method and Sims profiling of Cd Te. These analyses confirm the presence of hydrated CdCl{sub 2} and Cd Te phases on Cd Te surface and shown a good recrystallization morphology helping to the carriers mobility along the structure. Using the thermal treatment was possible to reduce the resistivity of Cd Te thin film; it is a result to the Cl migration along the Cd Te solar cell structure, reducing the defects between CdS and Cd Te thin films. A strong Cd Te thin film recrystallization was observed by the implementation of a hydrated-CdCl{sub 2} treatment doing to this a good candidate to Cd Te solar cells process. (Author)

Cumulative fatigue and creep-fatigue damage at 3500C on recrystallized zircaloy 4

International Nuclear Information System (INIS)

Brun, G.; Pelchat, J.; Floze, J.C.; Galimberti, M.

1985-06-01

An experimental programme undertaken by C.E.A., E.D.F. and FRAGEMA with the aim of characterizing the fatigue and creep fatigue behaviour of zircaloy-4 following annealing treatments (recrystallized, stress-delived) is in progress. The results given below concern only recrystallized material. Cyclic properties, low-cycle fatigue curves and creep behaviour laws under stresses have been established. Sequential tests of pure fatigue and creep-fatigue were performed. The cumulative life fractions at fracture depend on the sequence of leading, stress history and number of cycles of prestressing. The MINER's rule appears to be conservative with regard to a low-high loading sequence whereas it is not for the reverse high-low loading sequences. Fatigue and creep damage are not interchangeable. Pre-creep improves the fatigue resistance. Pre-fatigue improves the creep strength as long as the beneficial effect of cyclic hardening overcomes the damaging effect of surface cracking. The introduction of a tension hold time into the fatigue cycle slightly increases cyclic hardening and reduces the number of cycles to failure. For hold times of less than one hour, the sum of fatigue and creep life fractions is closed to one

Continuous recrystallization and mechanical properties of a C45 steel after high pressure torsion

Energy Technology Data Exchange (ETDEWEB)

Haddad, Mike; Fecht, Hans [Institute of Micro and Nanomaterials, University of Ulm, Ulm, Gemany (Germany); Institute of Nanotechnology, Karlsruhe Institut of Technology, Karlsruhe (Germany); Ning, Jiang Li; Ivanisenko, Yulia [Institute of Nanotechnology, Karlsruhe Institut of Technology, Karlsruhe (Germany); Hoermann, Ute [Central Facility for Electron Microscopy, University of Ulm, Ulm (Germany); Murashkin, Maxim [IPAM, Ufa State Aviation Technical University, Ufa (Russian Federation)

2011-07-01

An initial microstructure of C45 steel (Fe, 0.42-0.5% C, 0.5-0.8% Mn, <0.4% Si, <0.045% S, 0.045% P * All in wt%) was modified from ferritic-pearlitic to bainitic through heating at 900 C for 1 hour and quenching in a lead bath at 500 C for 30 min. The steel was processed by High Pressure Torsion (HPT) at room temperature for 3 and 5 rotations, which led to an ultrafine or nano-scale grained structure. Then the material was annealed at 400 C and 450 C for two hours, respectively. TEM observation showed that continuous recrystallization occurred during the annealing. The yield strength and elongation after annealing at 400 C and 450 C were 1277 MPa, 3%, and 1100 MPa, 11%, respectively. Compared with the mechanical properties before annealing, it was revealed that the continuous recrystallization during annealing led to an enhancement of the ductility, but without sacrificing much of the strength. Funding by the Deutsche Forschungsgemeinschaft and Russian Foundation for basic research is gratefully aknowledged.

Tracking the sleep onset process: an empirical model of behavioral and physiological dynamics.

Directory of Open Access Journals (Sweden)

Michael J Prerau

2014-10-01

Full Text Available The sleep onset process (SOP is a dynamic process correlated with a multitude of behavioral and physiological markers. A principled analysis of the SOP can serve as a foundation for answering questions of fundamental importance in basic neuroscience and sleep medicine. Unfortunately, current methods for analyzing the SOP fail to account for the overwhelming evidence that the wake/sleep transition is governed by continuous, dynamic physiological processes. Instead, current practices coarsely discretize sleep both in terms of state, where it is viewed as a binary (wake or sleep process, and in time, where it is viewed as a single time point derived from subjectively scored stages in 30-second epochs, effectively eliminating SOP dynamics from the analysis. These methods also fail to integrate information from both behavioral and physiological data. It is thus imperative to resolve the mismatch between the physiological evidence and analysis methodologies. In this paper, we develop a statistically and physiologically principled dynamic framework and empirical SOP model, combining simultaneously-recorded physiological measurements with behavioral data from a novel breathing task requiring no arousing external sensory stimuli. We fit the model using data from healthy subjects, and estimate the instantaneous probability that a subject is awake during the SOP. The model successfully tracked physiological and behavioral dynamics for individual nights, and significantly outperformed the instantaneous transition models implicit in clinical definitions of sleep onset. Our framework also provides a principled means for cross-subject data alignment as a function of wake probability, allowing us to characterize and compare SOP dynamics across different populations. This analysis enabled us to quantitatively compare the EEG of subjects showing reduced alpha power with the remaining subjects at identical response probabilities. Thus, by incorporating both

L2 Milestone 5433: Characterization of Dynamic Behavior of AM and Conventionally Processed Stainless Steel (316L and 304L)

Energy Technology Data Exchange (ETDEWEB)

Gray, George Thompson [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Livescu, Veronica [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rigg, P. A. [Washington State Univ., Pullman, WA (United States). Inst. for Shock Physics; Trujillo, Carl Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cady, Carl McElhinney [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chen, Shuh-Rong [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carpenter, John S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lienert, Thomas J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fensin, Saryu Jindal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Knapp, Cameron M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Beal, Roberta Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Morrow, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dippo, Olivia F. [Univ. of California, San Diego, CA (United States); Jones, David Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Daniel Tito [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Valdez, James Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-26

For additive manufacturing (AM) of metallic materials, the certification and qualification paradigm needs to evolve as there currently exists no broadly accepted “ASTM- or DIN-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, design, manufacture, and thereafter implementation and insertion of AM materials to meet engineering applications requires detailed quantification of the constitutive (strength and damage) properties of these evolving materials, across the spectrum of metallic AM methods, in comparison/contrast to conventionally-manufactured metals and alloys. This report summarizes the 316L SS research results and presents initial results of the follow-on study of 304L SS. For the AM-316L SS investigation, cylindrical samples of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS was characterized in both the “as-built” Additively Manufactured state and following a heat-treatment designed to obtain full recrystallization to facilitate comparison with annealed wrought 316L SS. The dynamic shock-loading-induced damage evolution and failure response of all three 316L SS materials was quantified using flyer-plate impact driven spallation experiments at peak stresses of 4.5 and 6.35 GPa. The results of these studies are reported in detail in the first section of the report. Publication of the 316L SS results in an archival journal is planned. Following on from the 316L SS completed work, initial results on a study of AM 304L SS are in progress and presented herein. Preliminary results on the structure/dynamic spallation property behavior of AM-304L SS fabricated using both the directed-energy LENS and an EOS powder-bed AM techniques in comparison to wrought 304L SS is detailed in this Level 2 Milestone report.

Nonlinear electromechanical modelling and dynamical behavior analysis of a satellite reaction wheel

Science.gov (United States)

Aghalari, Alireza; Shahravi, Morteza

2017-12-01

The present research addresses the satellite reaction wheel (RW) nonlinear electromechanical coupling dynamics including dynamic eccentricity of brushless dc (BLDC) motor and gyroscopic effects, as well as dry friction of shaft-bearing joints (relative small slip) and bearing friction. In contrast to other studies, the rotational velocity of the flywheel is considered to be controllable, so it is possible to study the reaction wheel dynamical behavior in acceleration stages. The RW is modeled as a three-phases BLDC motor as well as flywheel with unbalances on a rigid shaft and flexible bearings. Improved Lagrangian dynamics for electromechanical systems is used to obtain the mathematical model of the system. The developed model can properly describe electromechanical nonlinear coupled dynamical behavior of the satellite RW. Numerical simulations show the effectiveness of the presented approach.

Influence of initial heating during final high temperature annealing on the offset of primary and secondary recrystallization in Cu-bearing grain oriented electrical steels

Science.gov (United States)

Rodriguez-Calvillo, P.; Leunis, E.; Van De Putte, T.; Jacobs, S.; Zacek, O.; Saikaly, W.

2018-04-01

The industrial production route of Grain Oriented Electrical Steels (GOES) is complex and fine-tuned for each grade. Its metallurgical process requires in all cases the abnormal grain growth (AGG) of the Goss orientation during the final high temperature annealing (HTA). The exact mechanism of AGG is not yet fully understood, but is controlled by the different inhibition systems, namely MnS, AlN and CuxS, their size and distribution, and the initial primary recrystallized grain size. Therefore, among other parameters, the initial heating stage during the HTA is crucial for the proper development of primary and secondary recrystallized microstructures. Cold rolled 0.3 mm Cu-bearing Grain Oriented Electrical Steel has been submitted to interrupted annealing experiments in a lab tubular furnace. Two different annealing cycles were applied:• Constant heating at 30°C/h up to 1000°C. Two step cycle with initial heating at 100°C/h up to 600°C, followed by 18 h soaking at 600°C and then heating at 30°C/h up to 1050°C. The materials are analyzed in terms of their magnetic properties, grain size, texture and precipitates. The characteristic magnetic properties are analyzed for the different extraction temperatures and Cycles. As the annealing was progressing, the coercivity values (Hc 1.7T [A/m]) decreased, showing two abrupt drops, which can be associated to the on-set of primary and secondary recrystallization. The primary recrystallized grain sizes and recrystallized fractions are fitted to a model using a non-isothermal approach. This analysis shows that, although the resulting grain sizes were similar, the kinetics for the two step annealing were faster due to the lower recovery. The on-set of secondary recrystallization was also shifted to higher temperatures in the case of the continuous heating cycle, which might end in different final grain sizes and final magnetic properties. In both samples, nearly all the observed precipitates are Al-Si-Mn nitrides

Influence of initial heating during final high temperature annealing on the offset of primary and secondary recrystallization in Cu-bearing grain oriented electrical steels

Directory of Open Access Journals (Sweden)

P. Rodriguez-Calvillo

2018-04-01

Full Text Available The industrial production route of Grain Oriented Electrical Steels (GOES is complex and fine-tuned for each grade. Its metallurgical process requires in all cases the abnormal grain growth (AGG of the Goss orientation during the final high temperature annealing (HTA. The exact mechanism of AGG is not yet fully understood, but is controlled by the different inhibition systems, namely MnS, AlN and CuxS, their size and distribution, and the initial primary recrystallized grain size. Therefore, among other parameters, the initial heating stage during the HTA is crucial for the proper development of primary and secondary recrystallized microstructures. Cold rolled 0.3 mm Cu-bearing Grain Oriented Electrical Steel has been submitted to interrupted annealing experiments in a lab tubular furnace. Two different annealing cycles were applied:• Constant heating at 30°C/h up to 1000°C. Two step cycle with initial heating at 100°C/h up to 600°C, followed by 18 h soaking at 600°C and then heating at 30°C/h up to 1050°C. The materials are analyzed in terms of their magnetic properties, grain size, texture and precipitates. The characteristic magnetic properties are analyzed for the different extraction temperatures and Cycles. As the annealing was progressing, the coercivity values (Hc 1.7T [A/m] decreased, showing two abrupt drops, which can be associated to the on-set of primary and secondary recrystallization. The primary recrystallized grain sizes and recrystallized fractions are fitted to a model using a non-isothermal approach. This analysis shows that, although the resulting grain sizes were similar, the kinetics for the two step annealing were faster due to the lower recovery. The on-set of secondary recrystallization was also shifted to higher temperatures in the case of the continuous heating cycle, which might end in different final grain sizes and final magnetic properties. In both samples, nearly all the observed precipitates are Al

Structure/property (constitutive and dynamic strength/damage characterization of additively manufactured 316L SS

Directory of Open Access Journals (Sweden)

Gray III G.T.

2015-01-01

Full Text Available For additive manufacturing (AM, the certification and qualification paradigm needs to evolve as there exists no “ASTM-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, utilization of AM materials to meet engineering applications requires quantification of the constitutive properties of these evolving materials in comparison to conventionally-manufactured metals and alloys. Cylinders of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS is detailed in both the as-built condition and following heat-treatments designed to obtain full recrystallization. The constitutive behavior as a function of strain rate and temperature is presented and compared to that of nominal annealed wrought 316L SS plate. The dynamic damage evolution and failure response of all three materials was probed using flyer-plate impact driven spallation experiments at a peak stress of 4.5 GPa to examine incipient spallation response. The spall strength of AM-produced 316L SS was found to be very similar for the peak shock stress studied to that of annealed wrought or AM-316L SS following recrystallization. The damage evolution as a function of microstructure was characterized using optical metallography.

Synchronization effects in the dynamical behavior of elevators

Science.gov (United States)

Pöschel, Thorsten; Gallas, Jason A. C.

1994-10-01

We simulate the dynamical behavior of M elevators serving N floors of a building in which a Poisson distribution of persons call elevators. Our simulation reproduces the jamming effect typically seen in large buildings when a large number of persons decide to leave the building simultaneously. The collective behavior of the elevators involves characteristics similar to those observed in systems of coupled oscillators. In addition, there is an apparently rule-free critical population density above which elevators start to arrive synchronously at the ground floor.

Pressure effects on dynamics behavior of multiwall boron nitride nanotubes

Energy Technology Data Exchange (ETDEWEB)

Talebian, Taha [Faculty of Engineering, Neyshabur Branch, Islamic Azad University, Neyshabur (Iran, Islamic Republic of)

2016-01-15

The dynamic behavior of Multiwall boron nitride nanotubes (MWBNNTs) is investigated by employing multiple elastic shells model. The influences of van der Waals interactions on layers are shown as nonlinear functions of the interlayer distance of MWBNNTs. Governing equations are solved by using the developed finite element method and by employing time history diagrams. The radial wave speed from the outermost layer to the innermost layer is computed. The effects of geometrical factors such as diameter-to-thickness ratio on dynamic behavior of MWBNNTs are determined. The magnification aspects of MWBNNTs are computed, and the effects of surrounding pressures on wave speed and magnification aspect of MWBNNTs are discussed.

Mechanical and structural behaviour of uranium α, β, γ phases during plastic deformation

International Nuclear Information System (INIS)

Prunier, C.; Collot, C.

1981-06-01

High temperature behaviour of rich and poor uranium alloys in α, β and γ crystalline structures is studied: dynamic recrystallization phenomena begins only in α and β phases high temperature range, high strength and brittle β phase shows a very large ductility above 700 0 C. Dynamic recrystallization in γ phase rich alloys is observed only if large energy is available. Recrystallization is a thermal actived phenomena localised at grain boundary, dependant with alloy concentration and crystalline structure. β phase activation energy and deformation rate for dynamic recrystallization beginning are the most important in relation with structure complexity; both temperature and rate deformation are dynamic recrystallization factors [fr

Dynamic behaviors of cavitation bubble for the steady cavitating flow

Science.gov (United States)

Cai, Jun; Huai, Xiulan; Li, Xunfeng

2009-12-01

In this paper, by introducing the flow velocity item into the classical Rayleigh-Plesset dynamic equation, a new equation, which does not involve the time term and can describe the motion of cavitation bubble in the steady cavitating flow, has been obtained. By solving the new motion equation using Runge-Kutta fourth order method with adaptive step size control, the dynamic behaviors of cavitation bubble driven by the varying pressure field downstream of a venturi cavitation reactor are numerically simulated. The effects of liquid temperature (corresponding to the saturated vapor pressure of liquid), cavitation number and inlet pressure of venturi on radial motion of bubble and pressure pulse due to the radial motion are analyzed and discussed in detail. Some dynamic behaviors of bubble different from those in previous papers are displayed. In addition, the internal relationship between bubble dynamics and process intensification is also discussed. The simulation results reported in this work reveal the variation laws of cavitation intensity with the flow conditions of liquid, and will lay a foundation for the practical application of hydrodynamic cavitation technology.

Microstructure evolution of recrystallized Zircaloy-4 under charged particles irradiation

Science.gov (United States)

Gaumé, M.; Onimus, F.; Dupuy, L.; Tissot, O.; Bachelet, C.; Mompiou, F.

2017-11-01

Recrystallized zirconium alloys are used as nuclear fuel cladding tubes of Pressurized Water Reactors. During operation, these alloys are submitted to fast neutron irradiation which leads to their in-reactor deformation and to a change of their mechanical properties. These phenomena are directly related to the microstructure evolution under irradiation and especially to the formation of -type dislocation loops. In the present work, the radiation damage evolution in recrystallized Zircaloy-4 has been studied using charged particles irradiation. The loop nucleation and growth kinetics, and also the helical climb of linear dislocations, were observed in-situ using a High Voltage Electron Microscope (HVEM) under 1 MeV electron irradiation at 673 and 723 K. In addition, 600 keV Zr+ ion irradiations were conducted at the same temperature. Transmission Electron Microscopy (TEM) characterizations have been performed after both types of irradiations, and show dislocation loops with a Burgers vector belonging to planes close to { 10 1 bar 0 } first order prismatic planes. The nature of the loops has been characterized. Only interstitial dislocation loops have been observed after ion irradiation at 723 K. However, after electron irradiation conducted at 673 and 723 K, both interstitial and vacancy loops were observed, the proportion of interstitial loops increasing as the temperature is increased. The loop growth kinetics analysis shows that as the temperature increases, the loop number density decreases and the loop growth rate tends to increase. An increase of the flux leads to an increase of the loop number density and a decrease of the loop growth rate. The results are compared to previous works and discussed in the light of point defects diffusion.

Application of a mechanistic model for radiation-induced amorphization and crystallization of uranium silicide to recrystallization of UO2

International Nuclear Information System (INIS)

Rest, J.

1996-07-01

An alternative mechanism for the evolution of recrystallization nuclei is described for a model of irradiation-induced recrystallization of UO 2 wherein the stored energy in the material is concentrated in a network of sinklike nuclei that diminish with dose due to interaction with radiation-produced defects. The sinklike nuclei are identified as cellular dislocation structures that evolve relatively early in the irradiation period. A generalized theory of radiation-induced amorphization and crystallization, developed for intermetallic nuclear materials, is applied to UO 2 . The complicated kinetics involved in the formation of a cellular dislocation network are approximated by the formation and growth of subgrains due to the interaction of shock waves produced by fission- induced damage to the material

Public health impact of disease-behavior dynamics. Comment on "Coupled disease-behavior dynamics on complex networks: A review" by Z. Wang et al.

Science.gov (United States)

Wells, Chad R.; Galvani, Alison P.

2015-12-01

In a loop of dynamic feedback, behavior such as the decision to vaccinate, hand washing, or avoidance influences the progression of the epidemic, yet behavior is driven by the individual's and population's perceived risk of infection during an outbreak. In what we believe will become a seminal paper that stimulates future research as well as an informative teaching aid, Wang et. al. comprehensively review methodological advances that have been used to incorporate human behavior into epidemiological models on the effects of coupling disease transmission and behavior on complex social networks [1]. As illustrated by the recent outbreaks of measles and Middle Eastern Respiratory Syndrome (MERS), here we highlight the importance of coupling behavior and disease transmission that Wang et al. address.

Kinetic study of static recrystallization in an Fe–Al–O ultra-fine-grained nanocomposite

Czech Academy of Sciences Publication Activity Database

Bártková, Denisa; Šmíd, Miroslav; Mašek, B.; Svoboda, Jiří; Šiška, Filip

2017-01-01

Roč. 97, č. 10 (2017), s. 379-385 ISSN 0950-0839 R&D Projects: GA ČR GJ15-21292Y; GA MŠk LM2015069 Institutional support: RVO:68081723 Keywords : recrystallization * dislocation structures * nanoscale precipitates * microstructure * abrupt grain coarsening Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering, reliability analysis Impact factor: 0.941, year: 2016

Excimer laser recrystallization of nanocrystalline-Si films deposited by inductively coupled plasma chemical vapour deposition at 150 deg. C

International Nuclear Information System (INIS)

Park, Joong-Hyun; Han, Sang-Myeon; Park, Sang-Geun; Han, Min-Koo; Shin, Moon-Young

2006-01-01

Polycrystalline silicon thin film transistors (poly-Si TFTs) fabricated at low temperature (under 200 deg. C) have been widely investigated for flexible substrate applications such as a transparent plastic substrate. Unlike the conventional TFT process using glass substrate, the maximum process temperature should be kept less than 200 deg. C in order to avoid thermal damage on flexible substrates. We report the characteristics of nanocrystalline silicon (nc-Si) irradiated by an excimer laser. Nc-Si precursors were deposited on various buffer layers by inductively coupled plasma chemical vapour deposition (ICP-CVD) at 150 deg. C. We employed various buffer layers, such as silicon nitride (SiN X ) and silicon dioxide (SiO 2 ), in order to report recrystallization characteristics in connection with a buffer layer of a different thermal conductivity. The dehydrogenation and recrystallization was performed by step-by-step excimer laser annealing (ELA) (XeCl,λ=308 nm) in order to prevent the explosive release of hydrogen atoms. The grain size of the poly-Si film, which was recrystallized on the various buffer layers, was measured by scanning electron microscopy (SEM) at each laser energy density. The process margin of step-by-step ELA employing the SiN X buffer layer is wider than SiO 2 and the maximum grain size slightly increased

Three-dimensional investigation of recrystallization nucleation in a particle-containing Al alloy

DEFF Research Database (Denmark)

Zhang, Yonghao; Juul Jensen, Dorte; Zhang, Yubin

2012-01-01

The effects of an inhomogeneous distribution of second-phase particles on nucleation of recrystallization in a particle-containing aluminum alloy are investigated by 3-D serial sectioning. Clusters and bands of big intermetallic particles are the dominating nucleation sites, but other sites...... are also active. The effects of nucleation sites and the inhomogeneous particle distribution on the orientation and size of the nuclei are investigated and their relationships are discussed. 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved....

Simulating endogenous dynamics of activity-travel behavior : results of numerical simulations

NARCIS (Netherlands)

Psarra, I.; Liao, F.; Arentze, T.A.; Timmermans, H.J.P.

2013-01-01

Modelling the dynamics of activity-travel behavior constitutes the next challenge on the international research agenda. Long-term dynamics relate to changes in opportunities or constraints, such as residential and job choice, while short-term decisions relate to day-to-day experiences. Due to a

The developmental dynamics of behavioral growth processes in rodent egocentric and allocentric space.

Science.gov (United States)

Golani, Ilan

2012-06-01

In this review I focus on how three methodological principles advocated by Philip Teitelbaum influenced my work to this day: that similar principles of organization should be looked for in ontogeny and recovery of function; that the order of emergence of behavioral components provides a view on the organization of that behavior; and that the components of behavior should be exhibited by the animal itself in relatively pure form. I start by showing how these principles influenced our common work on the developmental dynamics of rodent egocentric space, and then proceed to describe how these principles affected my work with Yoav Benjamini and others on the developmental dynamics of rodent allocentric space. We analyze issues traditionally addressed by physiological psychologists with methods borrowed from ethology, EW (Eshkol-Wachman) movement notation, dynamical systems and exploratory data analysis. Then we show how the natural origins of axes embodied by the behavior of the organism itself, are used by us as the origins of axes for the measurement of the developmental moment-by-moment dynamics of behavior. Using this methodology we expose similar principles of organization across situations, species and preparations, provide a developmental view on the organization of behavior, expose the natural components of behavior in relatively pure form, and reveal how low level primitives generate higher level constructs. Advances in tracking technology should allow us to study how movements in egocentric and allocentric spaces interlace. Tracking of multi-limb coordination, progress in online recording of neural activity in freely moving animals, and the unprecedented accumulation of genetically engineered mouse preparations makes the behavioral ground plan exposed in this review essential for a systematic study of the brain/behavior interface. Copyright © 2012 Elsevier B.V. All rights reserved.

Inhibition of Ice Growth and Recrystallization by Zirconium Acetate and Zirconium Acetate Hydroxide

Science.gov (United States)

Mizrahy, Ortal; Bar-Dolev, Maya; Guy, Shlomit; Braslavsky, Ido

2013-01-01

The control over ice crystal growth, melting, and shaping is important in a variety of fields, including cell and food preservation and ice templating for the production of composite materials. Control over ice growth remains a challenge in industry, and the demand for new cryoprotectants is high. Naturally occurring cryoprotectants, such as antifreeze proteins (AFPs), present one solution for modulating ice crystal growth; however, the production of AFPs is expensive and inefficient. These obstacles can be overcome by identifying synthetic substitutes with similar AFP properties. Zirconium acetate (ZRA) was recently found to induce the formation of hexagonal cavities in materials prepared by ice templating. Here, we continue this line of study and examine the effects of ZRA and a related compound, zirconium acetate hydroxide (ZRAH), on ice growth, shaping, and recrystallization. We found that the growth rate of ice crystals was significantly reduced in the presence of ZRA and ZRAH, and that solutions containing these compounds display a small degree of thermal hysteresis, depending on the solution pH. The compounds were found to inhibit recrystallization in a manner similar to that observed in the presence of AFPs. The favorable properties of ZRA and ZRAH suggest tremendous potential utility in industrial applications. PMID:23555701

Analysis of dynamic cantilever behavior in tapping mode atomic force microscopy.

Science.gov (United States)

Deng, Wenqi; Zhang, Guang-Ming; Murphy, Mark F; Lilley, Francis; Harvey, David M; Burton, David R

2015-10-01

Tapping mode atomic force microscopy (AFM) provides phase images in addition to height and amplitude images. Although the behavior of tapping mode AFM has been investigated using mathematical modeling, comprehensive understanding of the behavior of tapping mode AFM still poses a significant challenge to the AFM community, involving issues such as the correct interpretation of the phase images. In this paper, the cantilever's dynamic behavior in tapping mode AFM is studied through a three dimensional finite element method. The cantilever's dynamic displacement responses are firstly obtained via simulation under different tip-sample separations, and for different tip-sample interaction forces, such as elastic force, adhesion force, viscosity force, and the van der Waals force, which correspond to the cantilever's action upon various different representative computer-generated test samples. Simulated results show that the dynamic cantilever displacement response can be divided into three zones: a free vibration zone, a transition zone, and a contact vibration zone. Phase trajectory, phase shift, transition time, pseudo stable amplitude, and frequency changes are then analyzed from the dynamic displacement responses that are obtained. Finally, experiments are carried out on a real AFM system to support the findings of the simulations. © 2015 Wiley Periodicals, Inc.

Dynamic behavior of hybrid sodium bearings. Theoretical and experimental studies

International Nuclear Information System (INIS)

Guidez, J.; Juignet, N.; Queval, M.

1981-08-01

The primary sodium pump shaft lower section of a fast breeder reactor is guided by a hydrostatic sodium bearing. This recess type bearing is supplied via orifices restrictors. Sodium is sampled at hight pressure at the diffuser outlet and is then centrifuged towards the orifices restrictors. Bearing stiffness and damping data is essential for the study of rotor dynamic behavior. Two points in particular may then be studied: - calculation of rotor instability ranges and critical speeds, - dynamic behavior of the rotor in the event of an earthquake. As regards the bearing design, the problem is to obtain the pressure fields in the liquid film. The integration of these pressure fields will then give the stiffness coefficients. The damping coefficients can then be obtained by the same calculation after slight displacement. The Reynolds equation can be used to study the liquid film (under any conditions for the turbulent and inertia effects). Then the computer code DELPAL is explained that solves the modified Reynolds equation using a finite element method. The presentation of tests conducted in 1981 on the Super-Phenix 1 full scall bearing (diameter 850 mm) in water is made. In conclusion this paper describes a method for calculating the stiffness and damping matrices of a hydrostatic bearing using the DELPAL calculation code and shows the loop of behavior tests on a bearing with sinusoidal excitation. The results, obtained by calculation and by testing, are indispensable when calculating the dynamic behavior of the shaft line

Inhibition of ice recrystallization and cryoprotective activity of wheat proteins in liver and pancreatic cells.

Science.gov (United States)

Chow-Shi-Yée, Mélanie; Briard, Jennie G; Grondin, Mélanie; Averill-Bates, Diana A; Ben, Robert N; Ouellet, François

2016-05-01

Efficient cryopreservation of cells at ultralow temperatures requires the use of substances that help maintain viability and metabolic functions post-thaw. We are developing new technology where plant proteins are used to substitute the commonly-used, but relatively toxic chemical dimethyl sulfoxide. Recombinant forms of four structurally diverse wheat proteins, TaIRI-2 (ice recrystallization inhibition), TaBAS1 (2-Cys peroxiredoxin), WCS120 (dehydrin), and TaENO (enolase) can efficiently cryopreserve hepatocytes and insulin-secreting INS832/13 cells. This study shows that TaIRI-2 and TaENO are internalized during the freeze-thaw process, while TaBAS1 and WCS120 remain at the extracellular level. Possible antifreeze activity of the four proteins was assessed. The "splat cooling" method for quantifying ice recrystallization inhibition activity (a property that characterizes antifreeze proteins) revealed that TaIRI-2 and TaENO are more potent than TaBAS1 and WCS120. Because of their ability to inhibit ice recrystallization, the wheat recombinant proteins TaIRI-2 and TaENO are promising candidates and could prove useful to improve cryopreservation protocols for hepatocytes and insulin-secreting cells, and possibly other cell types. TaENO does not have typical ice-binding domains, and the TargetFreeze tool did not predict an antifreeze capacity, suggesting the existence of nontypical antifreeze domains. The fact that TaBAS1 is an efficient cryoprotectant but does not show antifreeze activity indicates a different mechanism of action. The cryoprotective properties conferred by WCS120 depend on biochemical properties that remain to be determined. Overall, our results show that the proteins' efficiencies vary between cell types, and confirm that a combination of different protection mechanisms is needed to successfully cryopreserve mammalian cells. © 2016 The Protein Society.

Recrystallization in a Freezing Tolerant Antarctic Nematode, Panagrolaimus davidi, and a Alpine Weta, Hemideina maori (Orthoptera; Stenopelmatidae)

DEFF Research Database (Denmark)

Ramløv, Hans; Wharton, David A.; Wilson, Peter W.

1996-01-01

The ability of haemolymph from the freezing tolerant weta,Hemideina maori,and supernatant from homogenates of the freezing tolerant nematodePanagrolaimus davidito inhibit the recrystallization of ice was examined using the “splat freezing” technique and annealing on a cryomicroscope stage...

Low-temperature elastic anomalies in CaTiO3: dynamical characterization

Science.gov (United States)

Placeres-Jiménez, R.; Gonçalves, L. G. V.; Rino, J. P.; Fraygola, B.; Nascimento, W. J.; Eiras, J. A.

2012-11-01

Pulse-echo ultrasonic measurements of elastic coefficients of CaTiO3 show anomalous behavior around 200 K, with a notable rise in the attenuation coefficient. Molecular dynamics simulation is used to simulate the elastic response of a mono-domain (MDm) and a poly-domain (PDm) configuration of CaTiO3 using the Vashishta-Raman interatomic potential. The PDm is obtained by cooling the melt from 3600 to 300 K at a rate of 0.5 K ps-1, so that it recrystallizes to the PDm orthorhombic configuration. The elastic behavior is simulated in the temperature range from 300 to 20 K. In the MDm, it is observed that the bulk modulus varies linearly with temperature, while in the PDm an anomalous hardening is seen around 210 K. The bulk modulus of the PDm fluctuates strongly and is lower than that of the MDm. Neither the pair correlation function nor the Ti-Ti-O bonding angle indicate a true structural phase transition in this range of temperatures. Given the absence of any apparent change in the structure, a possible explanation for this phenomenon is the emergence of a certain class of dynamical instability associated with domain wall motion. Curiously, the pressure fluctuations in both the MDm and PDm configurations follow a power law distribution f ˜ P-α, with the exponent independent of applied strain and temperature. Time series for pressure are used to analyze the dynamics by time-delay reconstruction techniques. The calculus of embedding and correlation dimension indicates that in the polycrystalline configuration, low-dimension dynamics (<26) appears, which tend to disappear at higher temperatures.

Coordination: Neural, Behavioral and Social Dynamics

CERN Document Server

Fuchs, Armin

2008-01-01

One of the most striking features of Coordination Dynamics is its interdisciplinary character. The problems we are trying to solve in this field range from behavioral phenomena of interlimb coordination and coordination between stimuli and movements (perception-action tasks) through neural activation patterns that can be observed during these tasks to clinical applications and social behavior. It is not surprising that close collaboration among scientists from different fields as psychology, kinesiology, neurology and even physics are imperative to deal with the enormous difficulties we are facing when we try to understand a system as complex as the human brain. The chapters in this volume are not simply write-ups of the lectures given by the experts at the meeting but are written in a way that they give sufficient introductory information to be comprehensible and useful for all interested scientists and students.

Dynamic Socialized Gaussian Process Models for Human Behavior Prediction in a Health Social Network

Science.gov (United States)

Shen, Yelong; Phan, NhatHai; Xiao, Xiao; Jin, Ruoming; Sun, Junfeng; Piniewski, Brigitte; Kil, David; Dou, Dejing

2016-01-01

Modeling and predicting human behaviors, such as the level and intensity of physical activity, is a key to preventing the cascade of obesity and helping spread healthy behaviors in a social network. In our conference paper, we have developed a social influence model, named Socialized Gaussian Process (SGP), for socialized human behavior modeling. Instead of explicitly modeling social influence as individuals' behaviors influenced by their friends' previous behaviors, SGP models the dynamic social correlation as the result of social influence. The SGP model naturally incorporates personal behavior factor and social correlation factor (i.e., the homophily principle: Friends tend to perform similar behaviors) into a unified model. And it models the social influence factor (i.e., an individual's behavior can be affected by his/her friends) implicitly in dynamic social correlation schemes. The detailed experimental evaluation has shown the SGP model achieves better prediction accuracy compared with most of baseline methods. However, a Socialized Random Forest model may perform better at the beginning compared with the SGP model. One of the main reasons is the dynamic social correlation function is purely based on the users' sequential behaviors without considering other physical activity-related features. To address this issue, we further propose a novel “multi-feature SGP model” (mfSGP) which improves the SGP model by using multiple physical activity-related features in the dynamic social correlation learning. Extensive experimental results illustrate that the mfSGP model clearly outperforms all other models in terms of prediction accuracy and running time. PMID:27746515

Parameter study on dynamic behavior of ITER tokamak scaled model

International Nuclear Information System (INIS)

Nakahira, Masataka; Takeda, Nobukazu

2004-12-01

This report summarizes that the study on dynamic behavior of ITER tokamak scaled model according to the parametric analysis of base plate thickness, in order to find a reasonable solution to give the sufficient rigidity without affecting the dynamic behavior. For this purpose, modal analyses were performed changing the base plate thickness from the present design of 55 mm to 100 mm, 150 mm and 190 mm. Using these results, the modification plan of the plate thickness was studied. It was found that the thickness of 150 mm gives well fitting of 1st natural frequency about 90% of ideal rigid case. Thus, the modification study was performed to find out the adequate plate thickness. Considering the material availability, transportation and weldability, it was found that the 300mm thickness would be a limitation. The analysis result of 300mm thickness case showed 97% fitting of 1st natural frequency to the ideal rigid case. It was however found that the bolt length was too long and it gave additional twisting mode. As a result, it was concluded that the base plate thickness of 150mm or 190mm gives sufficient rigidity for the dynamic behavior of the scaled model. (author)

The dynamic behavior of the SUPER-PHENIX reactor under unprotected transient

International Nuclear Information System (INIS)

Gouriou, A.; Francillon, E.; Kayser, G.; Malenfer, G.; Languille, A.

1982-01-01

Due to design changes and progress on the knowledge of feed-back effects, a reactualization of the dynamic behavior of SUPER-PHENIX under unprotected transients was undertaken. We present the main data on feed-back characteristics and the results of dynamic calculations. With the present state of knowledge, the former conclusion is confirmed: the dynamic evolution is very slow and no irreversible phenomena happen in the short term

Spatiotemporal behavior and nonlinear dynamics in a phase conjugate resonator

Science.gov (United States)

Liu, Siuying Raymond

1993-01-01

The work described can be divided into two parts. The first part is an investigation of the transient behavior and stability property of a phase conjugate resonator (PCR) below threshold. The second part is an experimental and theoretical study of the PCR's spatiotemporal dynamics above threshold. The time-dependent coupled wave equations for four-wave mixing (FWM) in a photorefractive crystal, with two distinct interaction regions caused by feedback from an ordinary mirror, was used to model the transient dynamics of a PCR below threshold. The conditions for self-oscillation were determined and the solutions were used to define the PCR's transfer function and analyze its stability. Experimental results for the buildup and decay times confirmed qualitatively the predicted behavior. Experiments were carried out above threshold to study the spatiotemporal dynamics of the PCR as a function of Pragg detuning and the resonator's Fresnel number. The existence of optical vortices in the wavefront were identified by optical interferometry. It was possible to describe the transverse dynamics and the spatiotemporal instabilities by modeling the three-dimensional-coupled wave equations in photorefractive FWM using a truncated modal expansion approach.

The theory of reasoned action as parallel constraint satisfaction: towards a dynamic computational model of health behavior.

Directory of Open Access Journals (Sweden)

Mark G Orr

Full Text Available The reasoned action approach, although ubiquitous in health behavior theory (e.g., Theory of Reasoned Action/Planned Behavior, does not adequately address two key dynamical aspects of health behavior: learning and the effect of immediate social context (i.e., social influence. To remedy this, we put forth a computational implementation of the Theory of Reasoned Action (TRA using artificial-neural networks. Our model re-conceptualized behavioral intention as arising from a dynamic constraint satisfaction mechanism among a set of beliefs. In two simulations, we show that constraint satisfaction can simultaneously incorporate the effects of past experience (via learning with the effects of immediate social context to yield behavioral intention, i.e., intention is dynamically constructed from both an individual's pre-existing belief structure and the beliefs of others in the individual's social context. In a third simulation, we illustrate the predictive ability of the model with respect to empirically derived behavioral intention. As the first known computational model of health behavior, it represents a significant advance in theory towards understanding the dynamics of health behavior. Furthermore, our approach may inform the development of population-level agent-based models of health behavior that aim to incorporate psychological theory into models of population dynamics.

The theory of reasoned action as parallel constraint satisfaction: towards a dynamic computational model of health behavior.

Science.gov (United States)

Orr, Mark G; Thrush, Roxanne; Plaut, David C

2013-01-01

The reasoned action approach, although ubiquitous in health behavior theory (e.g., Theory of Reasoned Action/Planned Behavior), does not adequately address two key dynamical aspects of health behavior: learning and the effect of immediate social context (i.e., social influence). To remedy this, we put forth a computational implementation of the Theory of Reasoned Action (TRA) using artificial-neural networks. Our model re-conceptualized behavioral intention as arising from a dynamic constraint satisfaction mechanism among a set of beliefs. In two simulations, we show that constraint satisfaction can simultaneously incorporate the effects of past experience (via learning) with the effects of immediate social context to yield behavioral intention, i.e., intention is dynamically constructed from both an individual's pre-existing belief structure and the beliefs of others in the individual's social context. In a third simulation, we illustrate the predictive ability of the model with respect to empirically derived behavioral intention. As the first known computational model of health behavior, it represents a significant advance in theory towards understanding the dynamics of health behavior. Furthermore, our approach may inform the development of population-level agent-based models of health behavior that aim to incorporate psychological theory into models of population dynamics.

Dynamic behavior of PE-HD pipes grade

Czech Academy of Sciences Publication Activity Database

Trnka, Jan; Buchar, Jaroslav; Nezbedová, E.

2017-01-01

Roč. 373, č. 1 (2017), č. článku 1700038. ISSN 1022-1360 R&D Projects: GA MŠk(CZ) EF15_003/0000493 Institutional support: RVO:61388998 Keywords : dynamic behavior * PE-HD * split Hopkinson pressure bar test * strain rate Subject RIV: JI - Composite Materials OBOR OECD: Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics http://onlinelibrary.wiley.com/doi/10.1002/masy.201700038/full

Purification of ADU and high-molybdenum AUC by recrystallization

International Nuclear Information System (INIS)

Tan Huanchang; Wen Jinfeng

1995-01-01

The ADU was converted to AUC by preparing pulp with (NH 4 ) 2 CO 3 concentrated solution, and then the prepared AUC (high-molybdenum AUC) crystals were dissolved with hot soft water for dissolution, and after filtration or clarification and scrubbing of the residue, and the clarified solution was digested and the obtained pulp was thickened and the thickened pulp was converted and recrystallized by adding (NH 4 ) 2 CO 3 concentrated solution. The crystals were washed and filtrated, and then the high-purity AUC crystals were prepared. The laboratory and pilot-plant scale experiments showed that the presented purification process was feasible with the solvent extraction step eliminated, so the chemicals consumption would be considerably decreased and the environmental pollution would be lowered. It is easy to realize the process in practice

Dynamic behavior and chaos control in a complex Riccati-type map ...

African Journals Online (AJOL)

This paper is devoted to analyze the dynamic behavior of a Riccati- type map with complex variables and complex parameters. Fixed points and their asymptotic stability are studied. Lyapunov exponent is computed to indicate chaos. Bifurcation and chaos are discussed. Chaotic behavior of the map has been controlled by ...

Parameter-Independent Dynamical Behaviors in Memristor-Based Wien-Bridge Oscillator

Directory of Open Access Journals (Sweden)

Ning Wang

2017-01-01

Full Text Available This paper presents a novel memristor-based Wien-bridge oscillator and investigates its parameter-independent dynamical behaviors. The newly proposed memristive chaotic oscillator is constructed by linearly coupling a nonlinear active filter composed of memristor and capacitor to a Wien-bridge oscillator. For a set of circuit parameters, phase portraits of a double-scroll chaotic attractor are obtained by numerical simulations and then validated by hardware experiments. With a dimensionless system model and the determined system parameters, the initial condition-dependent dynamical behaviors are explored through bifurcation diagrams, Lyapunov exponents, and phase portraits, upon which the coexisting infinitely many attractors and transient chaos related to initial conditions are perfectly offered. These results are well verified by PSIM circuit simulations.

Hot deformation behavior of austenite in HSLA-100 microalloyed steel

International Nuclear Information System (INIS)

Momeni, A.; Arabi, H.; Rezaei, A.; Badri, H.; Abbasi, S.M.

2011-01-01

Research highlights: → The flow stress is well fitted by the exponential constitutive equation. → The average value of apparent activation energy for hot deformation is 377 kJ mol -1 . → A yield point phenomenon is observed on flow curves at high temperatures. → The Avrami exponent is determined around unity for dynamic recrystallization. - Abstract: Dynamic recrystallization of austenite in the Cu-bearing HSLA-100 steel was investigated by hot compression testing at a temperature range of 850-1150 deg. C and a strain rate of 0.001-1 s -1 . The obtained flow curves at temperatures higher than 950 deg. C were typical of DRX while at lower temperatures the flow curves were associated with work hardening without any indication of DRX. At high temperatures, flow stress exhibited a linear relation with temperature while at temperatures below 950 deg. C the behavior changed to non-linear. Hence, the temperature of 950 deg. C was introduced as the T nr of the alloy. All the flow curves showed a yield point elongation like phenomenon which was attributed to the interaction of solute atoms, notably carbon, and moving dislocations. The maximum elongation associated with the yield point phenomenon was observed at about 950 deg. C. Since the maximum yield point elongation was observed about the calculated T nr , it was concluded that carbon atoms were responsible for it. It was also concluded that the temperature at which the yield point elongation reaches the maximum value increases as strain rate rises. The stress and strain of the characteristic points of DRX flow curves were successfully correlated to the Zener-Hollomon parameter, Z, by power-law equations. The constitutive exponential equation was found more precise than the hyperbolic sine equation for modeling the dependence of flow stress on Z. The apparent activation energy for DRX was determined as 377 kJ mol -1 . The kinetics of DRX was modeled by an Avrami-type equation and the Avrami's exponent was

Using Difference Equation to Model Discrete-time Behavior in System Dynamics Modeling

NARCIS (Netherlands)

Hesan, R.; Ghorbani, A.; Dignum, M.V.

2014-01-01

In system dynamics modeling, differential equations have been used as the basic mathematical operator. Using difference equation to build system dynamics models instead of differential equation, can be insightful for studying small organizations or systems with micro behavior. In this paper we

Effects of elastic support on the dynamic behaviors of the wind turbine drive train

Institute of Scientific and Technical Information of China (English)

Shuaishuai WANG; Caichao ZHU; Chaosheng SONG; Huali HAN

2017-01-01

The reliability and service life of wind turbines are influenced by the complex loading applied on the hub,especially amidst a poor external wind environment.A three-point elastic support,which includes the main bearing and two torque arms,was considered in this study.Based on the flexibilities of the planet carrier and the housing,a coupled dynamic model was developed for a wind turbine drive train.Then,the dynamic behaviors of the drive train for different elastic support parameters were computed and analyzed.Frequency response functions were used to examine how different elastic support parameters influence the dynamic behaviors of the drive train.Results showed that the elastic support parameters considerably influenced the dynamic behaviors of the wind turbine drive train.A large support stiffness of the torque arms decreased the dynamic response of the planet carrier and the main bearing,whereas a large support stiffness of the main bearing decreased the dynamic response of planet carrier while increasing that of the main bearing.The findings of this study provide the foundation for optimizing the elastic support stiffness of the wind turbine drive train.

Study of mechanical properties from 77 to 900 K and of recovery-recrystallization of zircaloy 4

International Nuclear Information System (INIS)

Derep, J.L.

1981-09-01

Tensile tests carried out on zircaloy-4 between 77 and 900 K show five deformation domains: 1) 77-100 K the deformation is controlled by dislocation-interstitial interaction; 2) 180-205 K alternally activated transition zone with a Orowan process; 3) 250-600 K a thermally activated zone with mobile dislocations through interstitial clusters; 4) 600-700 K two mechanisms are superposed: Orowan or Frank and Read for the migration of dislocations fixed to the Frank network and a Snoek order associated to a dynamic hardening; 5) above 700 K another thermally activated zone. In the study of recovery-recrystallization the mechanisms were determined. Recovery is controlled by polygonisation leading to a cellular structure and annihilation of dislocations of opposite sign producing the growth of the cells. In the crystallisation the germination is controlled by the same mechanism and the growth by interactions between boundaries and second phase precipitates (Zrsub(x)-Fe 5 -Cr 2 ). It is then evident that zircaloy-4 plates used in PWR reactors between 350 and 450 0 C will evolve with time (even without the supplementary effect of irradiation) [fr

Dynamic behavior of microscale particles controlled by standing bulk acoustic waves

Energy Technology Data Exchange (ETDEWEB)

Greenhall, J.; Raeymaekers, B., E-mail: bart.raeymaekers@utah.edu [Department of Mechanical Engineering, University of Utah, Salt Lake City, Utah 84112 (United States); Guevara Vasquez, F. [Department of Mathematics, University of Utah, Salt Lake City, Utah 84112 (United States)

2014-10-06

We analyze the dynamic behavior of a spherical microparticle submerged in a fluid medium, driven to the node of a standing bulk acoustic wave created by two opposing transducers. We derive the dynamics of the fluid-particle system taking into account the acoustic radiation force and the time-dependent and time-independent drag force acting on the particle. Using this dynamic model, we characterize the transient and steady-state behavior of the fluid-particle system as a function of the particle and fluid properties and the transducer operating parameters. The results show that the settling time and percent overshoot of the particle trajectory are dependent on the ratio of the acoustic radiation force and time-independent damping force. In addition, we show that the particle oscillates around the node of the standing wave with an amplitude that depends on the ratio of the time-dependent drag forces and the particle inertia.

Amorphization and recrystallization in MeV ion implanted InP crystals

International Nuclear Information System (INIS)

Xiong, F.; Nieh, C.W.; Jamieson, D.N.; Vreeland, T. Jr.; Tombrello, T.A.

1988-01-01

A comprehensive study of MeV- 15 N-ion-implanted InP by a variety of analytical techniques has revealed the physical processes involved in MeV ion implantation into III-V compound semiconductors as well as the influence of post-implantation annealing. It provides a coherent picture of implant distribution, structural transition, crystalline damage, and lattice strain in InP crystals induced by ion implantation and thermal annealing. The experimental results from the different measurements are summarized in this report. Mechanisms of amorphization by implantation and recrystallization through annealing in MeV-ion-implanted InP are proposed and discussed in light of the results obtained

Effect of Strain Rate on Hot Ductility Behavior of a High Nitrogen Cr-Mn Austenitic Steel

Science.gov (United States)

Wang, Zhenhua; Meng, Qing; Qu, Minggui; Zhou, Zean; Wang, Bo; Fu, Wantang

2016-03-01

18Mn18Cr0.6N steel specimens were tensile tested between 1173 K and 1473 K (900 °C and 1200 °C) at 9 strain rates ranging from 0.001 to 10 s-1. The tensile strained microstructures were analyzed through electron backscatter diffraction analysis. The strain rate was found to affect hot ductility by influencing the strain distribution, the extent of dynamic recrystallization and the resulting grain size, and dynamic recovery. The crack nucleation sites were primarily located at grain boundaries and were not influenced by the strain rate. At 1473 K (1200 °C), a higher strain rate was beneficial for grain refinement and preventing hot cracking; however, dynamic recovery appreciably occurred at 0.001 s-1 and induced transgranular crack propagation. At 1373 K (1100 °C), a high extent of dynamic recrystallization and fine new grains at medium strain rates led to good hot ductility. The strain gradient from the interior of the grain to the grain boundary increased with decreasing strain rate at 1173 K and 1273 K (900 °C and 1000 °C), which promoted hot cracking. Grain boundary sliding accompanied grain rotation and did not contribute to hot cracking.

The developmental dynamics of task-avoidant behavior and math performance in kindergarten and elementary school

OpenAIRE

Hirvonen, Riikka; Tolvanen, Asko; Aunola, Kaisa; Nurmi, Jari-Erik

2012-01-01

Besides cognitive factors, children's learning at school may be influenced by more dynamic phenomena, such as motivation and achievement-related task-avoidant behavior. The present study examined the developmental dynamics of task-avoidant behavior and math performance from kindergarten to Grade 4. A total of 225 children were tested for their arithmetic skills in kindergarten and in Grades 1, 2, and 4 of elementary school. Children's task-avoidant behavior in learning situations was rated by...

New Insights on the Recrystallization and New Growth of Extensively Radiation-damaged Zircon

Science.gov (United States)

Hanchar, J. M.; Schmitz, M. D.; Wirth, R.

2012-12-01

Approximately 10 grams of cm-sized nearly metamict zircon crystals from the Saranac Prospect in the Bancroft District of Ontario were combined by breaking into small pieces and then ground under ethanol to a fine powder with an agate mortar and pestle in order to make enough homogeneously mixed material for multiple powder X-Ray and diffraction scans, high-resolution transmission electron microscopy (HR-TEM) measurements, and chemical abrasion isotope dilution thermal ionization mass spectrometry (CA-TIMS). While these large zircon crystals ground to a powder have a larger surface area and not in the same physical state (i.e., brown and metamict) as what is typically analyzed in single zircon CA-ID-TIMS U-Pb analysis (clear euhedral grains), the physical and chemical changes that occur during the heat treatment used in CA-TIMS are thought to be similar processes. Aliquots of the ground zircon powder were annealed in situ using a Pt furnace in a powder diffractometer during which time simultaneous powder diffraction patterns were acquired starting at 25°C, at elevated temperature (from 500°C to 1400°C) at selected time intervals, and then again at 25°C. The powder X-ray diffraction results indicate that below ~900°C the recrystallization of the zircon powder commences but is incomplete, even after 36 hours, with diffuse low intensity diffraction peaks. At 1150°C the zircon powder shows significant recrystallization. At 1150°C, the recrystallization is essentially complete in less than one hour. Before heating the zircon powder samples consisted of clear, transparent to brown, translucent, complexly zoned fragments. After heating at 900°C the zircon powder retained a smaller percentage of clear or brown complexly zoned fragments, while the majority of material had transformed to oscillatory or irregularly zoned, dominantly white opaque microcrystalline fragments. The clear fragments were hypothesized to be preexisting original crystalline zircon, the brown

Behavioral Dynamics in Swimming: The Appropriate Use of Inertial Measurement Units.

Science.gov (United States)

Guignard, Brice; Rouard, Annie; Chollet, Didier; Seifert, Ludovic

2017-01-01

Motor control in swimming can be analyzed using low- and high-order parameters of behavior. Low-order parameters generally refer to the superficial aspects of movement (i.e., position, velocity, acceleration), whereas high-order parameters capture the dynamics of movement coordination. To assess human aquatic behavior, both types have usually been investigated with multi-camera systems, as they offer high three-dimensional spatial accuracy. Research in ecological dynamics has shown that movement system variability can be viewed as a functional property of skilled performers, helping them adapt their movements to the surrounding constraints. Yet to determine the variability of swimming behavior, a large number of stroke cycles (i.e., inter-cyclic variability) has to be analyzed, which is impossible with camera-based systems as they simply record behaviors over restricted volumes of water. Inertial measurement units (IMUs) were designed to explore the parameters and variability of coordination dynamics. These light, transportable and easy-to-use devices offer new perspectives for swimming research because they can record low- to high-order behavioral parameters over long periods. We first review how the low-order behavioral parameters (i.e., speed, stroke length, stroke rate) of human aquatic locomotion and their variability can be assessed using IMUs. We then review the way high-order parameters are assessed and the adaptive role of movement and coordination variability in swimming. We give special focus to the circumstances in which determining the variability between stroke cycles provides insight into how behavior oscillates between stable and flexible states to functionally respond to environmental and task constraints. The last section of the review is dedicated to practical recommendations for coaches on using IMUs to monitor swimming performance. We therefore highlight the need for rigor in dealing with these sensors appropriately in water. We explain the

Dynamical behavior and Jacobi stability analysis of wound strings

Science.gov (United States)

Lake, Matthew J.; Harko, Tiberiu

2016-06-01

We numerically solve the equations of motion (EOM) for two models of circular cosmic string loops with windings in a simply connected internal space. Since the windings cannot be topologically stabilized, stability must be achieved (if at all) dynamically. As toy models for realistic compactifications, we consider windings on a small section of mathbb {R}^2, which is valid as an approximation to any simply connected internal manifold if the winding radius is sufficiently small, and windings on an S^2 of constant radius mathcal {R}. We then use Kosambi-Cartan-Chern (KCC) theory to analyze the Jacobi stability of the string equations and determine bounds on the physical parameters that ensure dynamical stability of the windings. We find that, for the same initial conditions, the curvature and topology of the internal space have nontrivial effects on the microscopic behavior of the string in the higher dimensions, but that the macroscopic behavior is remarkably insensitive to the details of the motion in the compact space. This suggests that higher-dimensional signatures may be extremely difficult to detect in the effective (3+1)-dimensional dynamics of strings compactified on an internal space, even if configurations with nontrivial windings persist over long time periods.

Dynamical behavior and Jacobi stability analysis of wound strings

Energy Technology Data Exchange (ETDEWEB)

Lake, Matthew J. [Naresuan University, The Institute for Fundamental Study, ' ' The Tah Poe Academia Institute' ' , Phitsanulok (Thailand); Thailand Center of Excellence in Physics, Ministry of Education, Bangkok (Thailand); Harko, Tiberiu [Babes-Bolyai University, Department of Physics, Cluj-Napoca (Romania); University College London, Department of Mathematics, London (United Kingdom)

2016-06-15

We numerically solve the equations of motion (EOM) for two models of circular cosmic string loops with windings in a simply connected internal space. Since the windings cannot be topologically stabilized, stability must be achieved (if at all) dynamically. As toy models for realistic compactifications, we consider windings on a small section of R{sup 2}, which is valid as an approximation to any simply connected internal manifold if the winding radius is sufficiently small, and windings on an S{sup 2} of constant radius R. We then use Kosambi-Cartan-Chern (KCC) theory to analyze the Jacobi stability of the string equations and determine bounds on the physical parameters that ensure dynamical stability of the windings. We find that, for the same initial conditions, the curvature and topology of the internal space have nontrivial effects on the microscopic behavior of the string in the higher dimensions, but that the macroscopic behavior is remarkably insensitive to the details of the motion in the compact space. This suggests that higher-dimensional signatures may be extremely difficult to detect in the effective (3+1)-dimensional dynamics of strings compactified on an internal space, even if configurations with nontrivial windings persist over long time periods. (orig.)

Effect of rolling reduction on the development of rolling and recrystallization textures in Al-Mg alloys

Energy Technology Data Exchange (ETDEWEB)

Endou, S; Inagaki, H [Shonan Inst. of Tech., Fujisawashi (Japan)

2002-07-01

In order to investigate the effect of Mg content on the development of the rolling textures in Al pure Al, Al-3% Mg alloy and Al-5% Mg alloy were cold rolled by varying rolling reductions up to 97%. Their rolling textures were investigated by the orientation distribution function analysis. The extent of work hardening introduced by cold rolling was estimated by the hardness measurements. It was found that, at all rolling reductions, the main orientations of the rolling textures depended strongly on the Mg content. In pure Al, {l_brace}123{r_brace} left angle 634 right angle was always the main orientation, whereas {l_brace}112{r_brace} left angle 111 right angle was most strong in the Al-3%Mg alloy. In the Al-5% Mg alloy, the development of both {l_brace}123{r_brace} left angle 634 right angle and {l_brace}112{r_brace} left angle 111 right angle were strongly suppressed, whereas {l_brace}110{r_brace} left angle 112 right angle developed remarkably. In pure Al, most of the texture development occurred at the later half of work hardening, i.e. at rolling reductions above 70%. With increasing Mg content, rolling texture tended to develop already at lower rolling reductions. Dynamic recovery, which occurred at very high rolling reductions, suppressed the development of the rolling textures. All these results strongly suggested that the formation of dislocation cell structures and shear banding are origins of the formation of these rolling textures. On annealing these specimens at 450 C for 30 min, recrystallization textures developed only in specimens having strong rolling textures, i. e. in the specimens cold rolled more than 70%. {l_brace}100{r_brace} left angle 001 right angle developed only in pure Al and in the Al-3% Mg ally, in which {l_brace}123{r_brace} left angle 634 right angle and {l_brace}112{r_brace} left angle 111 right angle were strong in the rolling textures. Recrystallization textures of the Al-5% Mg alloy was wather random. Its main orientation, {l

Dynamic magnetic behavior of the mixed-spin bilayer system in an oscillating field within the mean-field theory

International Nuclear Information System (INIS)

Ertaş, Mehmet; Keskin, Mustafa

2012-01-01

The dynamic magnetic behavior of the mixed Ising bilayer system (σ=2 and S=5/2), with a crystal-field interaction in an oscillating field are studied, within the mean-field approach, by using the Glauber-type stochastic dynamics for both ferromagnetic/ferromagnetic and antiferromagnetic/ferromagnetic interactions. The time variations of average magnetizations and the temperature dependence of the dynamic magnetizations are investigated. The dynamic phase diagrams are presented in the reduced temperature and magnetic field amplitude plane and they exhibit several ordered phases, coexistence phase regions and critical points as well as a re-entrant behavior depending on interaction parameters. -- Highlights: ► Dynamic magnetic behavior of the mixed Ising bilayer system is investigated within the Glauber-type stochastic dynamics. ► The time variations of average magnetizations are studied to find the phases. ► The temperature dependence of the dynamic magnetizations is investigated to obtain the dynamic phase transition points. ► The dynamic phase diagrams are presented and they exhibit several ordered phases, coexistence phase regions and critical points as well as a re-entrant behavior.

Dynamic magnetic behavior of the mixed-spin bilayer system in an oscillating field within the mean-field theory

Energy Technology Data Exchange (ETDEWEB)

Ertaş, Mehmet [Department of Physics, Erciyes University, 38039 Kayseri (Turkey); Keskin, Mustafa, E-mail: keskin@erciyes.edu.tr [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)

2012-07-23

The dynamic magnetic behavior of the mixed Ising bilayer system (σ=2 and S=5/2), with a crystal-field interaction in an oscillating field are studied, within the mean-field approach, by using the Glauber-type stochastic dynamics for both ferromagnetic/ferromagnetic and antiferromagnetic/ferromagnetic interactions. The time variations of average magnetizations and the temperature dependence of the dynamic magnetizations are investigated. The dynamic phase diagrams are presented in the reduced temperature and magnetic field amplitude plane and they exhibit several ordered phases, coexistence phase regions and critical points as well as a re-entrant behavior depending on interaction parameters. -- Highlights: ► Dynamic magnetic behavior of the mixed Ising bilayer system is investigated within the Glauber-type stochastic dynamics. ► The time variations of average magnetizations are studied to find the phases. ► The temperature dependence of the dynamic magnetizations is investigated to obtain the dynamic phase transition points. ► The dynamic phase diagrams are presented and they exhibit several ordered phases, coexistence phase regions and critical points as well as a re-entrant behavior.

Certain peculiarities of structural inheritance in phase recrystallization of steel

International Nuclear Information System (INIS)

Mukhamedov, A.A.

1978-01-01

The structural inheritance in phase recrystallization of previously overheated to various temperatures industrially melted 40Kh steel and of Armco-iron has been investigated. The steels have been heated to 100O, 11O0, 1200 and 1260 deg C and cooled in the air, and in some instances, hardened (quenched) in water. The physical broadening of X-ray lines points to a nonmonotonous variation of fine structure parameters as a function of the temperature and the heating time. The inheritance effect of fine structure defects affects the steel properties obtained in a final heat treatment. The structural inheritance effect has an important bearing upon the wear resistance of steel. A purpose-oriented use of the structural inheritance effect can enhance service properties of steel parts

Nucleation of recrystallization at selected sites in deformed fcc metals

DEFF Research Database (Denmark)

Xu, Chaoling

The objective of this thesis is to explore nucleation of recrystallization at selected sites in selected face-centered-cubic (FCC) metals, namely cold rolled columnar-grained nickel and high purity aluminum further deformed by indenting. Various techniques, including, optical microscopy, electron...... backscattered diffraction (EBSD), electron channeling contrast (ECC) and synchrotron X-ray technique, differential-aperture X-ray microscopy (DAXM), were used to characterize the microstructures, to explore nucleation sites, orientation relationships between nuclei and deformed microstructures, and nucleation...... mechanisms. In the cold rolled nickel samples, the preference of triple junctions (TJs) and grain boundaries (GBs) as nucleation sites is observed. The majorities of the nuclei have the same orientations as the surrounding matrix or are twin-related to a surrounding deformed grain. Only a few nuclei...

ALTERNATIVE EQUATIONS FOR DYNAMIC BEHAVIOR OF IONIC CHANNEL ACTIVATION AND INACTIVATION GATES

Directory of Open Access Journals (Sweden)

Mahmut ÖZER

2003-03-01

Full Text Available In this paper, alternative equations for dynamics of ionic channel activation and inactivation gates are proposed based on the path probability method. Dynamic behavior of a voltage-gated ionic channel is modeled by the conventional Hodgkin-Huxley (H-H mathematical formalism. In that model, conductance of the channel is defined in terms of activation and inactivation gates. Dynamics of the activation and inactivation gates is modeled by first-order differential equations dependent on the gate variable and the membrane potential. In the new approach proposed in this study, dynamic behavior of activation and inactivation gates is modeled by a firstorder differential equation dependent on internal energy and membrane potential by using the path probability method which is widely used in statistical physics. The new model doesn't require the time constant and steadystate values which are used explicitly in the H-H model. The numerical results show validity of the proposed method.

Simulation of the Dynamic Behavior of an Asynchronous Machine Using Direct Self-Control

Directory of Open Access Journals (Sweden)

Cristian Paul Chioncel

2007-01-01

Full Text Available The paper presents the major steps that have to be gone for the implementation of the mathematical model of the asynchronous machine in SciLab / Scicos. This implemented ASM model, will be used to check the dynamic behavior of the system, the current diagrams as well as the behavior motor speed and the torque, if the input signal has a pulsation form. This implementation’s are made in Scilab / Scicos environment, a clone of the MATLAB, which provides number-crunching power similar to MATLAB, at a much better cost/performance ratio. The implemented model offers the possibility to analyze the behaviors of the asynchronous machine in different dynamic situations: speed, torques, current in motor or generator regime and to study its behavior in different possible control schemes.

Effects of CdCl2 treatment on the recrystallization and electro-optical properties of CdTe thin films

International Nuclear Information System (INIS)

Moutinho, H.R.; Al-Jassim, M.M.; Levi, D.H.; Dippo, P.C.; Kazmerski, L.L.

1998-01-01

The effects of CdCl 2 processing on the physical and electro-optical properties of CdTe were evaluated for thin films produced by physical vapor deposition and close-spaced sublimation (CSS). Two substrates (CdS and Indium - tin - oxide) were used with the physical vapor deposition (PVD) films specifically to isolate the effects of the Cd(S x Te 1-x ) alloy formed during the treatment of films deposited on CdS. The samples were analyzed by x-ray diffraction (XRD), atomic force microscopy (AFM), and photoluminescence. The observed changes in microstructure were caused by recrystallization, which consisted of the nucleation and development of a new CdTe structure and subsequent grain growth. Nevertheless, for these processes to take place, it was necessary that enough lattice-strain energy was available in the films. For this reason, PVD films did recrystallize, while CSS films did not. For the first time, recrystallization was observed directly in AFM images of CdTe films and confirmed by XRD analysis, which indicated the existence of two lattice parameters in PVD samples treated at 350 degree C. For samples treated at 400 degree C, the CdCl 2 treatment improved the minority-carrier lifetime of the films by more than one order of magnitude. This improvement was attributed to the elimination of deep defect levels within the band gap of the CdTe films as a result of the treatment. The sulfur diffusion into CdTe films deposited on CdS, during the CdCl 2 treatment at 400 degree C, strongly affected the defect structure

Swift heavy ion-beam induced amorphization and recrystallization of yttrium iron garnet

International Nuclear Information System (INIS)

Costantini, Jean-Marc; Miro, Sandrine; Beuneu, François; Toulemonde, Marcel

2015-01-01

Pure and (Ca and Si)-substituted yttrium iron garnet (Y 3 Fe 5 O 12 or YIG) epitaxial layers and amorphous films on gadolinium gallium garnet (Gd 3 Ga 5 O 12 , or GGG) single crystal substrates were irradiated by 50 MeV 32 Si and 50 MeV (or 60 MeV) 63 Cu ions for electronic stopping powers larger than the threshold value (∼4 MeV μm −1 ) for amorphous track formation in YIG crystals. Conductivity data of crystalline samples in a broad ion fluence range (10 11 –10 16 cm −2 ) are modeled with a set of rate equations corresponding to the amorphization and recrystallization induced in ion tracks by electronic excitations. The data for amorphous layers confirm that a recrystallization process takes place above ∼10 14 cm −2 . Cross sections for both processes deduced from this analysis are discussed in comparison to previous determinations with reference to the inelastic thermal-spike model of track formation. Micro-Raman spectroscopy was also used to follow the related structural modifications. Raman spectra show the progressive vanishing and randomization of crystal phonon modes in relation to the ion-induced damage. For crystalline samples irradiated at high fluences (⩾10 14 cm −2 ), only two prominent broad bands remain like for amorphous films, thereby reflecting the phonon density of states of the disordered solid, regardless of samples and irradiation conditions. The main band peaked at ∼660 cm −1 is assigned to vibration modes of randomized bonds in tetrahedral (FeO 4 ) units. (paper)

Unraveling complex nonlinear elastic behaviors in rocks using dynamic acousto-elasticity

Science.gov (United States)

Riviere, J.; Guyer, R.; Renaud, G.; TenCate, J. A.; Johnson, P. A.

2012-12-01

In comparison with standard nonlinear ultrasonic methods like frequency mixing or resonance based measurements that allow one to extract average, bulk variations of modulus and attenuation versus strain level, dynamic acousto-elasticity (DAE) allows to obtain the elastic behavior over the entire dynamic cycle, detailing the full nonlinear behavior under tension and compression, including hysteresis and memory effects. This method consists of exciting a sample in Bulk-mode resonance at strains of 10-7 to 10-5 and simultaneously probing with a sequence of high frequency, low amplitude pulses. Time of flight and amplitudes of these pulses, respectively related to nonlinear elastic and dissipative parameters, can be plotted versus vibration strain level. Despite complex nonlinear signatures obtained for most rocks, it can be shown that for low strain amplitude (Pasqualini et al., JGR 2007), but not with the extreme detail of elasticity provided by DAE. Previous quasi-static measurements made in Berea sandstone (Claytor et al, GRL 2009), show that the hysteretic behavior disappears when the protocol is performed at a very low strain-rate (static limit). Therefore, future work will aim at linking quasi-static and dynamic observations, i.e. the frequency or strain-rate dependence, in order to understand underlying physical phenomena.

Nucleation of recrystallization observed in situ in the bulk of a deformed metal

International Nuclear Information System (INIS)

Larsen, Axel W.; Poulsen, Henning F.; Margulies, Lawrence; Gundlach, Carsten; Xing Qingfeng; Huang Xiaoxu; Jensen, Dorte Juul

2005-01-01

Nucleation of recrystallization is studied in situ in the bulk by three-dimensional X-ray diffraction. Copper samples cold rolled 20% are investigated. The crystallographic orientations near triple junction lines are characterized before, during and after annealing. Three nuclei are identified and it is shown that two nuclei are twin related to their parent grain and one nucleus has an orientation, which is neither present in the deformed parent grains nor first order twin related to any of them. Data on the nucleation kinetics is also presented

An overview of the crash dynamics failure behavior of metal and composite aircraft structures

Science.gov (United States)

Carden, Huey D.; Boitnott, Richard L.; Fasanella, Edwin L.; Jones, Lisa E.

1991-01-01

An overview of failure behavior results is presented from some of the crash dynamics research conducted with concepts of aircraft elements and substructure not necessarily designed or optimized for energy absorption or crash loading considerations. Experimental and analytical data are presented that indicate some general trends in the failure behavior of a class of composite structures that includes fuselage panels, individual fuselage sections, fuselage frames, skeleton subfloors with stringers and floor beams without skin covering, and subfloors with skin added to the frame stringer structure. Although the behavior is complex, a strong similarity in the static/dynamic failure behavior among these structures is illustrated through photographs of the experimental results and through analytical data of generic composite structural models.

Dynamic Viscoelastic Behavior and Phase Morphology of HIPS/HDPE Blends

OpenAIRE

LIU Jing-ru; XIA Yang-yang; GAO Li-qun; YU Qiang

2017-01-01

The dynamic viscoelastic behavior and phase morphology of high impact polystyrene (HIPS)/high density polyethylene (HDPE) blends were investigated by dynamic rheological test and scanning electron microscopy (SEM). The compatibilizing effect of 1%(mass fraction, same as below) micron-CaCO3 and nano-CaCO3 on HIPS/HDPE(30/70) immiscible blend was compared. The results indicate that the complex viscosity and storage modulus of HIPS/HDPE blends at low frequencies show positive deviation from the ...

ULTRASONIC STUDIES OF THE FUNDAMENTAL MECHANISMS OF RECRYSTALLIZATION AND SINTERING OF METALS

Energy Technology Data Exchange (ETDEWEB)

TURNER, JOSEPH A.

2005-11-30

The purpose of this project was to develop a fundamental understanding of the interaction of an ultrasonic wave with complex media, with specific emphases on recrystallization and sintering of metals. A combined analytical, numerical, and experimental research program was implemented. Theoretical models of elastic wave propagation through these complex materials were developed using stochastic wave field techniques. The numerical simulations focused on finite element wave propagation solutions through complex media. The experimental efforts were focused on corroboration of the models developed and on the development of new experimental techniques. The analytical and numerical research allows the experimental results to be interpreted quantitatively.

Dynamic behavior of a solid particle bed in a liquid pool

International Nuclear Information System (INIS)

Liu Ping; Yasunaka, Satoshi; Matsumoto, Tatsuya; Morita, Koji; Fukuda, Kenji; Yamano, Hidemasa; Tobita, Yoshiharu

2007-01-01

Dynamic behavior of solid particle beds in a liquid pool against pressure transients was investigated to model the mobility of core materials in a postulated disrupted core of a liquid metal fast reactor. A series of experiments was performed with a particle bed of different bed heights, comprising different monotype solid particles, where variable initial pressures of the originally pressurized nitrogen gas were adopted as the pressure sources. Computational simulations of the experiments were performed using SIMMER-III, a fast reactor safety analysis code. Comparisons between simulated and experimental results show that the physical model for multiphase flows used in the SIMMER-III code can reasonably represent the transient behaviors of pool multiphase flows with rich solid phases, as observed in the current experiments. This demonstrates the basic validity of the SIMMER-III code on simulating the dynamic behaviors induced by pressure transients in a low-energy disrupted core of a liquid metal fast reactor with rich solid phases

Molecular dynamics simulations of melting behavior of alkane as phase change materials slurry

International Nuclear Information System (INIS)

Rao Zhonghao; Wang Shuangfeng; Wu Maochun; Zhang Yanlai; Li Fuhuo

2012-01-01

Highlights: ► The melting behavior of phase change materials slurry was investigated by molecular dynamics simulation method. ► Four different PCM slurry systems including pure water and water/n-nonadecane composite were constructed. ► Amorphous structure and periodic boundary conditions were used in the molecular dynamics simulations. ► The simulated melting temperatures are very close to the published experimental values. - Abstract: The alkane based phase change materials slurry, with high latent heat storage capacity, is effective to enhance the heat transfer rate of traditional fluid. In this paper, the melting behavior of composite phase change materials slurry which consists of n-nonadecane and water was investigated by using molecular dynamics simulation. Four different systems including pure water and water/n-nonadecane composite were constructed with amorphous structure and periodic boundary conditions. The results showed that the simulated density and melting temperature were very close to the published experimental values. Mixing the n-nonadecane into water decreased the mobility but increased the energy storage capacity of composite systems. To describe the melting behavior of alkane based phase change materials slurry on molecular or atomic scale, molecular dynamics simulation is an effective method.

Technicolor and the asymptotic behavior of dynamically generated masses

International Nuclear Information System (INIS)

Natale, A.A.

1984-01-01

Arguments are given in favor of a hard asymptotic behavior of dynamically generated masses, its consequences for technicolor models are analyzed and a model is proposed, where effects of flavor changing neutral currents are highly supressed and pseudo Goldstone bosons get masses of O(30-90) GeV. (Author) [pt

Patterns of Stochastic Behavior in Dynamically Unstable High-Dimensional Biochemical Networks

Directory of Open Access Journals (Sweden)

Simon Rosenfeld

2009-01-01

Full Text Available The question of dynamical stability and stochastic behavior of large biochemical networks is discussed. It is argued that stringent conditions of asymptotic stability have very little chance to materialize in a multidimensional system described by the differential equations of chemical kinetics. The reason is that the criteria of asymptotic stability (Routh- Hurwitz, Lyapunov criteria, Feinberg’s Deficiency Zero theorem would impose the limitations of very high algebraic order on the kinetic rates and stoichiometric coefficients, and there are no natural laws that would guarantee their unconditional validity. Highly nonlinear, dynamically unstable systems, however, are not necessarily doomed to collapse, as a simple Jacobian analysis would suggest. It is possible that their dynamics may assume the form of pseudo-random fluctuations quite similar to a shot noise, and, therefore, their behavior may be described in terms of Langevin and Fokker-Plank equations. We have shown by simulation that the resulting pseudo-stochastic processes obey the heavy-tailed Generalized Pareto Distribution with temporal sequence of pulses forming the set of constituent-specific Poisson processes. Being applied to intracellular dynamics, these properties are naturally associated with burstiness, a well documented phenomenon in the biology of gene expression.

Bimanual coordination and musical experience : The role of intrinsic dynamics and behavioral information

NARCIS (Netherlands)

Verheul, M.H.G.; Geuze, RH

Rhythmic interlimb coordination arises from the interaction of intrinsic dynamics and behavioral information, that is, intention, memory, or external information specifying the required coordination pattern. This study investigates the influence of the content of memorized behavioral information on

An Experimental Investigation of the Dynamic Behavior of an In-Plane MEMS Shallow Arch Under Electrostatic Excitation

KAUST Repository

Ramini, Abdallah

2016-01-20

We present experimental investigation of the nonlinear dynamics of a clamped-clamped in-plane MEMS shallow arch when excited by an electrostatic force. We explore the dynamic behaviors of the in-plane motion of the shallow arches via frequency sweeps in the neighborhood of the first resonance frequency. The shallow arch response is video microscopy recorded and analyzed by means of digital imaging. The experimental data show local softening behavior for small DC and AC loads. For high voltages, the experimental investigation reveals interesting dynamics, where the arch exhibits a dynamic snap-Through behavior. These attractive experimental results verify the previously reported complex behavior of in-plane MEMS arches and show promising results to implement these structures for variety of sensing and actuation applications. © Copyright 2015 by ASME.

Analytical modeling of the thermomechanical behavior of ASTM F-1586 high nitrogen austenitic stainless steel used as a biomaterial under multipass deformation.

Science.gov (United States)

Bernardes, Fabiano R; Rodrigues, Samuel F; Silva, Eden S; Reis, Gedeon S; Silva, Mariana B R; Junior, Alberto M J; Balancin, Oscar

2015-06-01

Precipitation-recrystallization interactions in ASTM F-1586 austenitic stainless steel were studied by means of hot torsion tests with multipass deformation under continuous cooling, simulating an industrial laminating process. Samples were deformed at 0.2 and 0.3 at a strain rate of 1.0s(-1), in a temperature range of 900 to 1200°C and interpass times varying from 5 to 80s. The tests indicate that the stress level depends on deformation temperature and the slope of the equivalent mean stress (EMS) vs. 1/T presents two distinct behaviors, with a transition at around 1100°C, the non-recrystallization temperature (Tnr). Below the Tnr, strain-induced precipitation of Z-phase (NbCrN) occurs in short interpass times (tpass<30s), inhibiting recrystallization and promoting stepwise stress build-up with strong recovery, which is responsible for increasing the Tnr. At interpass times longer than 30s, the coalescence and dissolution of precipitates promote a decrease in the Tnr and favor the formation of recrystallized grains. Based on this evidence, the physical simulation of controlled processing allows for a domain refined grain with better mechanical properties. Copyright © 2015 Elsevier B.V. All rights reserved.

Dynamic Behavior of Fault Slip Induced by Stress Waves

Directory of Open Access Journals (Sweden)

Guang-an Zhu

2016-01-01

Full Text Available Fault slip burst is a serious dynamic hazard in coal mining. A static and dynamic analysis for fault slip was performed to assess the risk of rock burst. A numerical model FLAC3D was established to understand the stress state and mechanical responses of fault rock system. The results obtained from the analysis show that the dynamic behavior of fault slip induced by stress waves is significantly affected by mining depth, as well as dynamic disturbance intensity and the distance between the stope and the fault. The isolation effect of the fault is also discussed based on the numerical results with the fault angle appearing to have the strongest influence on peak vertical stress and velocity induced by dynamic disturbance. By taking these risks into account, a stress-relief technology using break-tip blast was used for fault slip burst control. This technique is able to reduce the stress concentration and increase the attenuation of dynamic load by fracturing the structure of coal and rock. The adoption of this stress-relief method leads to an effective reduction of fault slip induced rock burst (FSIRB occurrence.

A comparative study on the direct deposition of μc-Si:H and plasma-induced recrystallization of a-Si:H: Insight into Si crystallization in a high-density plasma

Science.gov (United States)

Zhou, H. P.; Xu, M.; Xu, S.; Feng, Y. Y.; Xu, L. X.; Wei, D. Y.; Xiao, S. Q.

2018-03-01

Deep insight into the crystallization mechanism of amorphous silicon is of theoretical and technological significance for the preparation of high-quality microcrystalline/polycrystalline silicon. In this work, we intensively compare the present two plasma-involved routes, i.e., the direct deposition and recrystallization of precursor amorphous silicon (a-Si) films, to fabricate microcrystalline silicon. Both the directly deposited and recrystallized samples show multi-layered structures as revealed by electronic microscopy. High-density hydrogen plasma involved recrystallization process, which is mediated by the hydrogen diffusion into the deep region of the precursor a-Si film, displays significantly different nucleation configuration, interface properties, and crystallite shape. The underlying mechanisms are analyzed in combination with the interplay of high-density plasma and growing or treated surface.

Stochastic Simulation of Isotopic Exchange Mechanisms for Fe(II)-Catalyzed Recrystallization of Goethite

Energy Technology Data Exchange (ETDEWEB)

Zarzycki, Piotr [Energy; Institute; Rosso, Kevin M. [Pacific Northwest

2017-06-15

Understanding Fe(II)-catalyzed transformations of Fe(III)- (oxyhydr)oxides is critical for correctly interpreting stable isotopic distributions and for predicting the fate of metal ions in the environment. Recent Fe isotopic tracer experiments have shown that goethite undergoes rapid recrystallization without phase change when exposed to aqueous Fe(II). The proposed explanation is oxidation of sorbed Fe(II) and reductive Fe(II) release coupled 1:1 by electron conduction through crystallites. Given the availability of two tracer exchange data sets that explore pH and particle size effects (e.g., Handler et al. Environ. Sci. Technol. 2014, 48, 11302-11311; Joshi and Gorski Environ. Sci. Technol. 2016, 50, 7315-7324), we developed a stochastic simulation that exactly mimics these experiments, while imposing the 1:1 constraint. We find that all data can be represented by this model, and unifying mechanistic information emerges. At pH 7.5 a rapid initial exchange is followed by slower exchange, consistent with mixed surface- and diffusion-limited kinetics arising from prominent particle aggregation. At pH 5.0 where aggregation and net Fe(II) sorption are minimal, that exchange is quantitatively proportional to available particle surface area and the density of sorbed Fe(II) is more readily evident. Our analysis reveals a fundamental atom exchange rate of ~10-5 Fe nm-2 s-1, commensurate with some of the reported reductive dissolution rates of goethite, suggesting Fe(II) release is the rate-limiting step in the conduction mechanism during recrystallization.

Deformation and recrystallization of Nb-10Si in-situ composite

International Nuclear Information System (INIS)

Saqib, M.; Thirukkonda, M.; Cockeram, B.; Srinivasan, R.; Weiss, I.

1993-01-01

Materials for elevated temperature applications require a balance of strength, fracture toughness, mechanical and microstructural stability over the temperature range between room temperature and service temperatures which are expected to exceed 1,200 C, as well as oxidation and creep resistance. Recent trends indicate that Carbon/Carbon and Ceramic/Ceramic Composites do not meet all of these requirements. For example, carbon/carbon composites have good strength to density ratio, but inherently possess poor oxidation resistance, and SiC/SiC composites ha e excellent oxidation resistance, but are brittle over the entire temperature range of their stability. Ductile phase toughened composites with refractory intermetallic matrices are attractive alternatives. At service temperatures of about 1,200 C, most of the applied load will be carried by the intermetallic matrix phase, while the ductile (metallic) phase increases toughness by impeding crack propagation. As compared to other materials with potential for elevated temperature applications, mentioned above, these materials provide a better combination of elevated temperature strength and room temperature fracture toughness. Nb 10 a/o Si is a model material for ductile phase toughened in situ composites. In the as-cast condition the microstructure contains both the ductile metallic niobium phase and the continuous inter-metallic Nb 3 Si phase. The microstructure of this in situ composite can be tailored by thermomechanical processing (TMP). The changes in the morphology and spacing of the phases, and microstructural refinement following TMP, have been shown to improve the fracture toughness of the alloy. as compared to the as-cast material. Therefore, understanding of the deformation behavior and the mechanisms of recovery and recrystallization are of great importance in tailoring the microstructure of in situ composites by TMP

Simulation of long-term dynamic behavior of runaway electrons

International Nuclear Information System (INIS)

Wang Yulei; Liu Jian; Zhang Ruili; He Yang

2015-01-01

The secular dynamics of runaway electrons in Tokamak electromagnetic field is studied. The radiation effect is added into a relativistic volume-preserving algorithm to gain long-term stability of calculation. The results shows that the method we used is able to reveal the behavior of a runaway electron in configuration space. (author)

Removal of SO42− from Li2CO3 by Recrystallization in Na2CO3 Solution

Directory of Open Access Journals (Sweden)

Wei Cai

2018-01-01

Full Text Available Li2CO3 with high purity is an important raw material for the fabrication of lithium rechargeable batteries. This paper reports a facile recrystallization way to produce Li2CO3 with high purity from commercial Li2CO3 containing 0.8 wt % of SO42− by the treatment of the commercial Li2CO3 in Na2CO3 solution. The increase of temperature from 30 °C to 90 °C favored the recrystallization of Li2CO3 in Na2CO3 solution and promoted the removal of SO42− adsorbed or doped on/in the commercial Li2CO3. The content of SO42− in Li2CO3 decreased to 0.08 wt % after the treatment of the commercial Li2CO3 in 1.0 mol·L−1 Na2CO3 solution at 90 °C for 10.0 h.

Experimental oligopolies modeling: A dynamic approach based on heterogeneous behaviors

Science.gov (United States)

Cerboni Baiardi, Lorenzo; Naimzada, Ahmad K.

2018-05-01

In the rank of behavioral rules, imitation-based heuristics has received special attention in economics (see [14] and [12]). In particular, imitative behavior is considered in order to understand the evidences arising in experimental oligopolies which reveal that the Cournot-Nash equilibrium does not emerge as unique outcome and show that an important component of the production at the competitive level is observed (see e.g.[1,3,9] or [7,10]). By considering the pioneering groundbreaking approach of [2], we build a dynamical model of linear oligopolies where heterogeneous decision mechanisms of players are made explicit. In particular, we consider two different types of quantity setting players characterized by different decision mechanisms that coexist and operate simultaneously: agents that adaptively adjust their choices towards the direction that increases their profit are embedded with imitator agents. The latter ones use a particular form of proportional imitation rule that considers the awareness about the presence of strategic interactions. It is noteworthy that the Cournot-Nash outcome is a stationary state of our models. Our thesis is that the chaotic dynamics arousing from a dynamical model, where heterogeneous players are considered, are capable to qualitatively reproduce the outcomes of experimental oligopolies.

Composite dynamical behaviors in a simple series–parallel LC circuit

International Nuclear Information System (INIS)

Manimehan, I.; Philominathan, P.

2012-01-01

Highlights: ► We have presented a simple circuit exhibiting rich dynamical behaviors. ► The detailed study of the circuit is given by two parameter bifurcation diagram. ► The numerical, analytical and experimental results are good in agreement. ► The Chosen system seems to have potential application in future. - Abstract: In this paper, we report a variety of dynamical behaviors exhibited in a compact series–parallel LC circuit system comprising of two active elements, one linear negative conductance and one ordinary junction diode with piecewise linear v − i characteristics. For convenience, we consider the amplitude (E f ) and frequency (f) of the driving force as control parameters amongst various other parameters. We observe the phenomenon of antimonotonicity, torus breakdown to chaos, bubbles to chaos, period doubling to chaos and emergence of multiple attractors which follow a progressive sequence, etc. As an overview to understand many more variety of bifurcations and attractors, the construction of two parameter phase diagram is also shown pictorially. The chaotic dynamics of this circuit is realized by laboratory experiment, numerical and analytical investigations and found that the results are in good agreement with each other.

Continuous monitoring the vehicle dynamics and driver behavior using navigation systems

Science.gov (United States)

Ene, George

2017-10-01

In all fields cost is very important and the increasing amount of data that are needed for active safety systems, like ADAS, lead to implementation of some complex and powerful unit for processing raw data. In this manner is necessary a cost-effective method to estimate the maximum available tire road friction during acceleration and braking by continuous monitoring the vehicle dynamics and driver behavior. The method is based on the hypothesis that short acceleration and braking periods can indicate vehicle dynamics, and thus the available tire road friction coefficient, and also human behavior and his limits. Support for this hypothesis is found in the literature and is supported by the result of experiments conducted under different conditions and seasons.

New orientation formation and growth during primary recrystallization in stable single crystals of three face-centred cubic metals

International Nuclear Information System (INIS)

Miszczyk, M.; Paul, H.; Driver, J.H.; Maurice, C.

2015-01-01

Graphical abstract: For Ni, Cu and Cu-2%Al and (1 1 0)[0 0 −1] and (1 1 0)[1 −1 −2] initial orientations at the initial stages of recrystallization, the appearance of a specific number of new orientation groups of new grains has been demonstrated. The orientation relations across the recrystallization front are characterized by a high proportion of angles in the range 25–35° and 45–55° around axes mostly grouped about the 〈1 2 2〉, 〈1 1 1〉, 〈1 2 3〉 and 〈1 1 2〉 directions. A local minimum was noted for the disorientation angle densities close to 40° in all cases. For a single isolated nucleus of uniform orientation, the rotation axes are usually grouped around one of the normals of all four {1 1 1} planes but do not (or only rarely) coincide with them. The orientation of the growing new grain quickly transforms through the formation of a first generation twins. The most frequent situation occurs when the normal of the twinning face plane is situated near the rotation axis, around which the crystal lattice of the ‘primary nuclei’ rotates. Based on the anisotropy of grain growth a possible mechanism of orientation generation and grain growth by thermally activation movement of dislocation families, on {1 1 1} planes is proposed. - Abstract: The early stages of recrystallization have been systematically characterized in single crystal metals of medium and low stacking fault energy. Goss {1 1 0}〈0 0 1〉 and brass {1 1 0}〈1 1 2〉 oriented samples of Ni, Cu and Cu–2 wt.% Al alloy were deformed in a channel die to a logarithmic strain of 0.51 to develop a homogeneous structure composed of two sets of symmetrical primary microbands and then lightly annealed. Scanning electron microscopy/electron backscattered diffraction analyses demonstrate a strong relation between as-deformed orientations and the limited number of recrystallized grain orientations. The disorientation angles across the recrystallization front are mostly grouped in

Multipass forging of Inconel 718 in the delta-Supersolvus domain: assessing and modeling microstructure evolution

Directory of Open Access Journals (Sweden)

Zouari Meriem

2014-01-01

Full Text Available This work is focused on the evolution of the microstructure of Inconel 718 during multi-pass forging processes. During the forming process, the material is subjected to several physical phenomena such as work-hardening, recovery, recrystallization and grain growth. In this work, transformation kinetics are modeled in the δ-Supersolvus domain (T>Tsolvus where the alloy is single-phase, all the alloying elements being dissolved into the FCC matrix. Torsion tests were used to simulate the forging process and recrystallization kinetics was modeled using a discontinuous dynamic recrystallization (DDRX two-site mean field model. The microstructure evolution under hot forging conditions is predicted in both dynamic and post-dynamic regimes based on the initial distribution of grain size and the evolution of dislocation density distribution during each step of the process. The model predicts recrystallization kinetics, recrystallized grain size distribution and stress–strain curve for different thermo-mechanical conditions and makes the connection between dynamic and post-dynamic regimes.

The Theory of Reasoned Action as Parallel Constraint Satisfaction: Towards a Dynamic Computational Model of Health Behavior

OpenAIRE

Orr, Mark G.; Thrush, Roxanne; Plaut, David C.

2013-01-01

The reasoned action approach, although ubiquitous in health behavior theory (e.g., Theory of Reasoned Action/Planned Behavior), does not adequately address two key dynamical aspects of health behavior: learning and the effect of immediate social context (i.e., social influence). To remedy this, we put forth a computational implementation of the Theory of Reasoned Action (TRA) using artificial-neural networks. Our model re-conceptualized behavioral intention as arising from a dynamic constrain...

Information behavior in dynamic group work contexts

DEFF Research Database (Denmark)

Sonnenwald, Diane H.; Pierce, Linda G.

2000-01-01

personnel and documentation on C2. During data analysis, three important themes that highlight the why, what, how and consequences of information behavior in C2 emerged. The first is the concept of interwoven situational awareness consisting of individual, intragroup and intergroup shared understanding...... of the situation. Interwoven situational awareness appears to facilitate response to dynamic, constraint-bound situations. The second theme describes the need for dense social networks or frequent communication between participants about the work context and situation, the work process and domain...

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation

Directory of Open Access Journals (Sweden)

Yue Hou

2017-02-01

Full Text Available Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM experiments, Phase Dynamics Theory and Molecular Dynamics (MD Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation.

Science.gov (United States)

Hou, Yue; Wang, Linbing; Wang, Dawei; Guo, Meng; Liu, Pengfei; Yu, Jianxin

2017-02-21

Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM) experiments, Phase Dynamics Theory and Molecular Dynamics (MD) Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

A model for strain hardening, recovery, recrystallization and grain growth with applications to forming processes of nickel base alloys

Czech Academy of Sciences Publication Activity Database

Riedel, H.; Svoboda, Jiří

2016-01-01

Roč. 665, MAY (2016), s. 175-183 ISSN 0921-5093 R&D Projects: GA ČR(CZ) GA14-24252S Institutional support: RVO:68081723 Keywords : Recrystallization * Recovery * Chaboche model Subject RIV: BJ - Thermodynamic s Impact factor: 3.094, year: 2016

Simulation of dynamics behaviors for shipping equipment support with system dynamics analysis approach

Directory of Open Access Journals (Sweden)

Yang Song

2015-05-01

Full Text Available Purpose: The exactly and precisely supply of carrying spare parts has a crucial impact on support and could improve the performance of equipment. Spare parts support is the crux work which will be limited by spare parts allocation and support cost input. Reasonable support strategy can help in making good use of available resources and support the equipment in normal operational status. The purpose of this paper is to propose a dynamics model of spare parts support process based on considering the interaction of multiple factors, and explores the regulation of dynamics behavior in the system. In order to achieve the optimization strategy to improve the effect of support so that will enhance the relevant support parameters of equipment. Design/methodology/approach: Meditate the feedback relationship among some important factors of support that involve support cost, support time and maintenance ability. System dynamics theory is adopted to propose a dynamics model of spare parts support process, on the analysis of multiple factors and casual relationship to find some major ones which have crucial impact on spare parts support. Spare parts support cost and availability was regarded as the control objective, moreover, adjust the control paramours and improve the effect of cannibalization and lateral supply scheduling strategy for spares support. Findings: The factors of spare parts supply, demand and maintenance have relationship of control feedback, and adjust the value of some crucial factors can reduce the support cost and improve the availability value. The main finding is that adopting cannibalization strategy under condition of available materials can relieve the mission and operational availability decline caused by shortage of spare parts. Combining the lateral supply and cannibalization strategy can reduce the inventory of warship carrying spare parts. Practical implications: By controlling the value of key factors regarding aspect of spare

Coprecipitation of {sup 14}C and Sr with carbonate precipitates: The importance of reaction kinetics and recrystallization pathways

Energy Technology Data Exchange (ETDEWEB)

Hodkin, David J. [School of Earth and Environment, University of Leeds, Leeds LS2 9JT (United Kingdom); Stewart, Douglas I. [School of Civil Engineering, University of Leeds (United Kingdom); Graham, James T. [National Nuclear Laboratory, Sellafield, Cumbria (United Kingdom); Burke, Ian T., E-mail: I.T.Burke@leeds.ac.uk [School of Earth and Environment, University of Leeds, Leeds LS2 9JT (United Kingdom)

2016-08-15

This study investigated the simultaneous removal of Sr{sup 2+} and {sup 14}CO{sub 3}{sup 2−} from pH > 12 Ca(OH){sub 2} solution by the precipitation of calcium carbonate. Initial Ca{sup 2+}:CO{sub 3}{sup 2−} ratios ranged from 10:1 to 10:100 (mM:mM). Maximum removal of {sup 14}C and Sr{sup 2+} both occurred in the system containing 10 mM Ca{sup 2+} and 1 mM CO{sub 3}{sup 2−} (99.7% and 98.6% removal respectively). A kinetic model is provided that describes {sup 14}C and Sr removal in terms of mineral dissolution and precipitation reactions. The removal of {sup 14}C was achieved during the depletion of the initial TIC in solution, and was subsequently significantly affected by recrystallization of the calcite precipitate from an elongate to isotropic morphology. This liberated > 46% of the {sup 14}C back to solution. Sr{sup 2+} removal occurred as Ca{sup 2+} became depleted in solution and was not significantly affected by the recrystallization process. The proposed reaction could form the basis for low cost remediation scheme for {sup 90}Sr and {sup 14}C in radioactively contaminated waters (<$0.25 reagent cost per m{sup 3} treated). - Highlights: • 99.7% of {sup 14}C and 98.6% of Sr removed from aqueous solution by CaCO{sub 3} precipitation. • Remobilization of {sup 14}C observed during calcium carbonate recrystallization. • Sr displayed variable distribution coefficient (possibly affected by Ca:Sr ratio). • Reagent cost of $0.22/m{sup 3} of treated groundwater.

The effect of heat treatment on recrystallized microstructure, precipitation and ductility of hot-rolled Fe–Cr–Al–REM ferritic stainless steel sheets

International Nuclear Information System (INIS)

Qu, H.P.; Lang, Y.P.; Yao, C.F.; Chen, H.T.; Yang, C.Q.

2013-01-01

This study presents research works about the effects of heat treatment on recrystallized equiaxed grain size, precipitation, room temperature (RT) toughness and ductile to brittle transition temperature (DBTT) of Fe–Cr–Al–REM ferritic stainless steel (FSS) hot-rolled sheet. Results showed that the recrystallization of hot-rolled Fe–Cr–Al–REM FSS sheet could be completed after annealing treatment at 750 °C for 15 min with the equiaxed grain diameter of approximately 50 μm. Inappropriate annealing treatment would inevitably leads to the unexpected grain coarsening. On the other hand, a great deal of needle-like or spot-like fine aluminum–lanthanum compound Al 11 La 3 precipitates were observed in the ferrite matrix after 1 h aging treatment at 750 °C. The microstructure observation results associated with the impact test definitely illustrated that the Al 11 La 3 precipitates was the reason for the brittle crack in the as-casted ingot and as-forged slab. The real DBTT of the annealed Fe–Cr–Al–REM FSS sheet with average grain size of about 50 μm was −4 °C. Meanwhile, the DBTT of the hot-rolled Fe–Cr–Al–REM stainless steel sheet was evidently increased as the recrystallized grain size increased.

Kinetic Analysis of Recovery, Recrystallization, and Phase Precipitation in an Al-Fe-Si Alloy Using JMAEK and Sesták-Berggren Models

Science.gov (United States)

Luiggi Agreda, Ney José

2015-02-01

When studying the phase changes process in a rolled AA8011 alloy using DSC, we find that the peaks associated with phase precipitation under this microstructural condition are different from those obtained in homogenized microstructures. The differences observed are attributable, first, to the recovery process occurring at temperatures below 423 K (150 °C), which interacts with the precipitation of Si-rich precipitates or with Guinier-Preston zones both coexistent in that temperature range; and second, to the recrystallization above 473 K (200 °C), which coexists with precipitation of the α-AlFeSi phase. In this work, the precipitation and recovery-recrystallization kinetics are experimentally obtained and deconvoluted in peaks characteristic for each of the mechanisms involved; i.e., precipitation of GP zones, recovery, precipitation of α phase, and recrystallization. The deconvolution is achieved using functions of Gauss, Weibull, and Fraser-Suzuki; and the characterization of each reaction deconvoluted is realized through both Jhonson-Melh-Avrami-Erofeev-Kolmorokov kinetic models and Sesták-Berggren combined kinetic model. The kinetic study evinces that in addition to the expected reactions, other reactions, necessary for good experimental adjustment, appear. An isoconversional study is undertaken to numerically evaluate the kinetic triplet of every process.

The effect of heat treatment on recrystallized microstructure, precipitation and ductility of hot-rolled Fe-Cr-Al-REM ferritic stainless steel sheets

Energy Technology Data Exchange (ETDEWEB)

Qu, H.P., E-mail: quhuapeng0926@163.com [Institute for Special Steels (Formerly Institute for Structural Materials), Central Iron and Steel Research Institute (CISRI), 76 HaiDianNan Road, Beijing 100081 (China); Lang, Y.P. [Institute for Special Steels (Formerly Institute for Structural Materials), Central Iron and Steel Research Institute (CISRI), 76 HaiDianNan Road, Beijing 100081 (China); Yao, C.F. [Institute for Special Steels (Formerly Institute for Structural Materials), Central Iron and Steel Research Institute (CISRI), 76 HaiDianNan Road, Beijing 100081 (China); Zhuozhou Works, Central Iron and Steel Research Institute (CISRI), 2 HuoJuNan Road, Zhuozhou 072750, Hebei (China); Chen, H.T.; Yang, C.Q. [Institute for Special Steels (Formerly Institute for Structural Materials), Central Iron and Steel Research Institute (CISRI), 76 HaiDianNan Road, Beijing 100081 (China)

2013-02-01

This study presents research works about the effects of heat treatment on recrystallized equiaxed grain size, precipitation, room temperature (RT) toughness and ductile to brittle transition temperature (DBTT) of Fe-Cr-Al-REM ferritic stainless steel (FSS) hot-rolled sheet. Results showed that the recrystallization of hot-rolled Fe-Cr-Al-REM FSS sheet could be completed after annealing treatment at 750 Degree-Sign C for 15 min with the equiaxed grain diameter of approximately 50 {mu}m. Inappropriate annealing treatment would inevitably leads to the unexpected grain coarsening. On the other hand, a great deal of needle-like or spot-like fine aluminum-lanthanum compound Al{sub 11}La{sub 3} precipitates were observed in the ferrite matrix after 1 h aging treatment at 750 Degree-Sign C. The microstructure observation results associated with the impact test definitely illustrated that the Al{sub 11}La{sub 3} precipitates was the reason for the brittle crack in the as-casted ingot and as-forged slab. The real DBTT of the annealed Fe-Cr-Al-REM FSS sheet with average grain size of about 50 {mu}m was -4 Degree-Sign C. Meanwhile, the DBTT of the hot-rolled Fe-Cr-Al-REM stainless steel sheet was evidently increased as the recrystallized grain size increased.

Microstructure and High Temperature Plastic Deformation Behavior of Al-12Si Based Alloy Fabricated by an Electromagnetic Casting and Stirring Process

Energy Technology Data Exchange (ETDEWEB)

Jeon, Kyung-Soo; Roh, Heung-Ryeol; Kim, Mok-Soon [Inha University, Incheon (Korea, Republic of); Kim, Jong-Ho; Park, Joon-Pyo [Research Institute of Industrial Science and Technology, Pohang (Korea, Republic of)

2017-06-15

An as-received EMC/S (electromagnetic casting and stirring)-processed Al-12Si based alloy billet was homogenized to examine its microstructure and high temperature plastic deformation behavior, using compressive tests over the temperature range from 623 to 743 K and a strain rate range from 1.0×10{sup -3} to 1.0×10{sup 0}s{sup -1}. The results were compared with samples processed by the direct chill casting (DC) method. The fraction of equiaxed structure for the as-received EMC/S billet(41%) was much higher than that of the as-received DC billet(6 %). All true stress – true strain curves acquired from the compressive tests exhibited a peak stress at the initial stage of plastic deformation. Flow stress showed a steady state region after the appearance of peak stress with increasing strain. The peak stress decreased with increasing temperature at a given strain rate and a decreasing strain rate at a given temperature. A constitutive equation was made for each alloy, which could be used to predict the peak stress. A recrystallized grain structure was observed in all the deformed specimens, indicating that dynamic recrystallization is the predominant mechanism during high temperature plastic deformation of both the homogenized EMC/S and DC-processed Al-12Si based alloys.

Shear-wave dynamic behavior using two different orientations

International Nuclear Information System (INIS)

Ghassem Alaskari, M. K.; Hashemi, S. J.

2007-01-01

For laterally complex media, it may be more suitable to take a different orientation of the displacement vector of Shear-waves. This may change the sign of several imaginary reflections and conversion coefficients to be used in reservoir characterization and Amplitude Versus Offset analysis or modeling. In this new convention the positive direction of the displacement vector of reflected Shear-waves is chosen to the left of ray tangent (in the direction of wave propagation). Therefore, the definition of the displacement vector of shear-waves can be used properly even for very complicated media. Finally the shear-wave dynamic behavior of a reservoir zone can be illustrated for laterally varying structures in terms of the amplitude variation and phase behavior using this new orientation

CO2 laser-induced directional recrystallization to produce single crystal silicon-core optical fibers with low loss

OpenAIRE

Healy, Noel; Fokine, Michael; Franz, Yohann; Hawkins, Thomas; Jones, Maxwell; Ballato, John; Peacock, Anna C.; Gibson, Ursula J.

2016-01-01

Reduced losses in silicon-core fibers are obtained using CO2 laser directional recrystallization of the core. Single crystals with aspect ratios up to 1500:1 are reported, limited by the scan range of the equipment. This processing technique holds promise for bringing crystalline silicon-core fibers to a central role in nonlinear optics and signal processing applications.

The dynamic behavior of the exohedral transition metal complexes ...

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences; Volume 129; Issue 7. The dynamic behavior of the exohedral transition metal complexes of B₄₀ : η⁶- and η⁷-B₄₀Cr(CO) ₃ and Cr(CO) ₃η⁷-B₄η₀-Cr(CO) ₃. NAIWRIT KARMODAK ELUVATHINGAL D JEMMIS. REGULAR ARTICLE Volume 129 Issue 7 July 2017 pp ...

Research on Power Producer’s Bidding Behavior Based on the Best-Response Dynamic Model

Directory of Open Access Journals (Sweden)

Jingqi Sun

2014-01-01

Full Text Available As China’s electricity market is facing many problems, the research on power producer’s bidding behavior can promote the healthy and sustainable development of China’s electricity market. As a special commodity, the “electricity” possesses complicated production process. The instable market constraint condition, nonsymmetric information, and a lot of random factors make the producer’s bidding process more complex. Best-response dynamic is one of the classic dynamic mechanisms of the evolutionary game theory, which applies well in the repeated game and strategy evolution that happen among a few bounded rational players with a quick learning capability. The best-response dynamic mechanism is employed to study the power producer’s bidding behavior in this paper, the producer’s best-response dynamic model is constructed, and how the producers would engage in bidding is analyzed in detail. Taking two generating units in South China regional electricity market as the example, the producer’s bidding behavior by following the producer’s best-response dynamic model is verified. The relationships between the evolutionarily stable strategy (ESS of power producer’s bidding and the market demand, and ceiling and floor price as well as biding frequency are discussed in detail.

The Feldenkrais Method: A Dynamic Approach to Changing Motor Behavior.

Science.gov (United States)

Buchanan, Patricia A.; Ulrich, Beverly D.

2001-01-01

Describes the Feldenkrais Method of somatic education, noting parallels with a dynamic systems theory (DST) approach to motor behavior. Feldenkrais uses movement and perception to foster individualized improvement in function. DST explains that a human-environment system continually adapts to changing conditions and assembles behaviors…

Dynamic behavior of homogeneous and heterogeneous LMFBR core-design concepts

International Nuclear Information System (INIS)

Chang, Y.I.; Henryson, H. II; Orechwa, Y.; Su, S.F.; Greenman, G.; Blomquist, R.

1981-01-01

The emphasis is placed on obtaining an understanding of the inherent difference between homogeneous and heterogeneous core configurations regarding neutronic characteristics related to the dynamic behavior. The space-time neutronic and thermal-hydraulic behavior was analyzed in detail for various core configurations by using the FX2-TH, a two-dimensional kinetics code with thermal-hydraulic feedback. In addition, the relationship between the flux tilt and the fundamental-to-first harmonic eigenvalue separation, and the sodium void reactivity in heterogeneous cores were also sutdied

An investigation of the static and dynamic behavior of electrically actuated rectangular microplates

KAUST Repository

Saghir, S.

2016-06-16

We present an investigation of the static and dynamic behavior of the nonlinear von-Karman plates when actuated by the nonlinear electrostatic forces. The investigation is based on a reduced order model developed using the Galerkin method, which rely on modeshapes and in-plane shape functions extracted using a finite element method. In this study, a fully clamped microplate is considered. We investigate the static behavior and the effect of different non-dimensional design parameters. The static results are validated by comparison with the results calculated by a finite element model. The forced-vibration response of the plate is then investigated when the plate is excited by a harmonic AC load superimposed to a DC load. The dynamic behavior is examined near the primary and secondary (superharmonic and subharmonic) resonances. The microplate shows a strong hardening behavior due to the cubic nonlinearity of mid-plane stretching. However, the behavior switches to softening as the DC load is increased. Finally, near-square plates are studied to understand the effect of geometric imperfections of microplates.

An investigation of the static and dynamic behavior of electrically actuated rectangular microplates

KAUST Repository

Saghir, Shahid; Younis, Mohammad I.

2016-01-01

We present an investigation of the static and dynamic behavior of the nonlinear von-Karman plates when actuated by the nonlinear electrostatic forces. The investigation is based on a reduced order model developed using the Galerkin method, which rely on modeshapes and in-plane shape functions extracted using a finite element method. In this study, a fully clamped microplate is considered. We investigate the static behavior and the effect of different non-dimensional design parameters. The static results are validated by comparison with the results calculated by a finite element model. The forced-vibration response of the plate is then investigated when the plate is excited by a harmonic AC load superimposed to a DC load. The dynamic behavior is examined near the primary and secondary (superharmonic and subharmonic) resonances. The microplate shows a strong hardening behavior due to the cubic nonlinearity of mid-plane stretching. However, the behavior switches to softening as the DC load is increased. Finally, near-square plates are studied to understand the effect of geometric imperfections of microplates.

Dynamical Integration of Language and Behavior in a Recurrent Neural Network for Human--Robot Interaction

Directory of Open Access Journals (Sweden)

Tatsuro Yamada

2016-07-01

Full Text Available To work cooperatively with humans by using language, robots must not only acquire a mapping between language and their behavior but also autonomously utilize the mapping in appropriate contexts of interactive tasks online. To this end, we propose a novel learning method linking language to robot behavior by means of a recurrent neural network. In this method, the network learns from correct examples of the imposed task that are given not as explicitly separated sets of language and behavior but as sequential data constructed from the actual temporal flow of the task. By doing this, the internal dynamics of the network models both language--behavior relationships and the temporal patterns of interaction. Here, ``internal dynamics'' refers to the time development of the system defined on the fixed-dimensional space of the internal states of the context layer. Thus, in the execution phase, by constantly representing where in the interaction context it is as its current state, the network autonomously switches between recognition and generation phases without any explicit signs and utilizes the acquired mapping in appropriate contexts. To evaluate our method, we conducted an experiment in which a robot generates appropriate behavior responding to a human's linguistic instruction. After learning, the network actually formed the attractor structure representing both language--behavior relationships and the task's temporal pattern in its internal dynamics. In the dynamics, language--behavior mapping was achieved by the branching structure. Repetition of human's instruction and robot's behavioral response was represented as the cyclic structure, and besides, waiting to a subsequent instruction was represented as the fixed-point attractor. Thanks to this structure, the robot was able to interact online with a human concerning the given task by autonomously switching phases.

Dynamical Integration of Language and Behavior in a Recurrent Neural Network for Human-Robot Interaction.

Science.gov (United States)

Yamada, Tatsuro; Murata, Shingo; Arie, Hiroaki; Ogata, Tetsuya

2016-01-01

To work cooperatively with humans by using language, robots must not only acquire a mapping between language and their behavior but also autonomously utilize the mapping in appropriate contexts of interactive tasks online. To this end, we propose a novel learning method linking language to robot behavior by means of a recurrent neural network. In this method, the network learns from correct examples of the imposed task that are given not as explicitly separated sets of language and behavior but as sequential data constructed from the actual temporal flow of the task. By doing this, the internal dynamics of the network models both language-behavior relationships and the temporal patterns of interaction. Here, "internal dynamics" refers to the time development of the system defined on the fixed-dimensional space of the internal states of the context layer. Thus, in the execution phase, by constantly representing where in the interaction context it is as its current state, the network autonomously switches between recognition and generation phases without any explicit signs and utilizes the acquired mapping in appropriate contexts. To evaluate our method, we conducted an experiment in which a robot generates appropriate behavior responding to a human's linguistic instruction. After learning, the network actually formed the attractor structure representing both language-behavior relationships and the task's temporal pattern in its internal dynamics. In the dynamics, language-behavior mapping was achieved by the branching structure. Repetition of human's instruction and robot's behavioral response was represented as the cyclic structure, and besides, waiting to a subsequent instruction was represented as the fixed-point attractor. Thanks to this structure, the robot was able to interact online with a human concerning the given task by autonomously switching phases.

A dynamic parking charge optimal control model under perspective of commuters' evolutionary game behavior

Science.gov (United States)

Lin, XuXun; Yuan, PengCheng

2018-01-01

In this research we consider commuters' dynamic learning effect by modeling the trip mode choice behavior from a new perspective of dynamic evolutionary game theory. We explore the behavior pattern of different types of commuters and study the evolution path and equilibrium properties under different traffic conditions. We further establish a dynamic parking charge optimal control (referred to as DPCOC) model to alter commuters' trip mode choice while minimizing the total social cost. Numerical tests show. (1) Under fixed parking fee policy, the evolutionary results are completely decided by the travel time and the only method for public transit induction is to increase the parking charge price. (2) Compared with fixed parking fee policy, DPCOC policy proposed in this research has several advantages. Firstly, it can effectively turn the evolutionary path and evolutionary stable strategy to a better situation while minimizing the total social cost. Secondly, it can reduce the sensitivity of trip mode choice behavior to traffic congestion and improve the ability to resist interferences and emergencies. Thirdly, it is able to control the private car proportion to a stable state and make the trip behavior more predictable for the transportation management department. The research results can provide theoretical basis and decision-making references for commuters' mode choice prediction, dynamic setting of urban parking charge prices and public transit induction.

Behavioral Priming 2.0: Enter a Dynamical Systems Perspective

Science.gov (United States)

Krpan, Dario

2017-01-01

On a daily basis, people are exposed to numerous stimuli, ranging from colors and smells to sounds and words, that could potentially activate different cognitive constructs and influence their actions. This type of influence on human behavior is referred to as priming. Roughly two decades ago, behavioral priming was hailed as one of the core forces that shape automatic behavior. However, failures to replicate some of the representative findings in this domain soon followed, which posed the following question: “How robust are behavioral priming effects, and to what extent are they actually important in shaping people's actions?” To shed a new light on this question, I revisit behavioral priming through the prism of a dynamical systems perspective (DSP). The DSP is a scientific paradigm that has been developed through a combined effort of many different academic disciplines, ranging from mathematics and physics to biology, economics, psychology, etc., and it deals with behavior of simple and complex systems over time. In the present paper, I use conceptual and methodological tools stemming from the DSP to propose circumstances under which behavioral priming effects are likely to occur. More precisely, I outline three possible types of the influence of priming on human behavior, to which I refer as emergence, readjustment, and attractor switch, and propose experimental designs to examine them. Finally, I discuss relevant implications for behavioral priming effects and their replications. PMID:28769846

Behavioral Priming 2.0: Enter a Dynamical Systems Perspective

Directory of Open Access Journals (Sweden)

Dario Krpan

2017-07-01

Full Text Available On a daily basis, people are exposed to numerous stimuli, ranging from colors and smells to sounds and words, that could potentially activate different cognitive constructs and influence their actions. This type of influence on human behavior is referred to as priming. Roughly two decades ago, behavioral priming was hailed as one of the core forces that shape automatic behavior. However, failures to replicate some of the representative findings in this domain soon followed, which posed the following question: “How robust are behavioral priming effects, and to what extent are they actually important in shaping people's actions?” To shed a new light on this question, I revisit behavioral priming through the prism of a dynamical systems perspective (DSP. The DSP is a scientific paradigm that has been developed through a combined effort of many different academic disciplines, ranging from mathematics and physics to biology, economics, psychology, etc., and it deals with behavior of simple and complex systems over time. In the present paper, I use conceptual and methodological tools stemming from the DSP to propose circumstances under which behavioral priming effects are likely to occur. More precisely, I outline three possible types of the influence of priming on human behavior, to which I refer as emergence, readjustment, and attractor switch, and propose experimental designs to examine them. Finally, I discuss relevant implications for behavioral priming effects and their replications.

Dynamic behavior of district heating systems

International Nuclear Information System (INIS)

Kunz, J.

1994-01-01

The goal of this study is to develop a simulation model of a hot water system taking into account the time dependent phenomena which are important for the operational management of such a system. A state of the art literature review has shown that there is no such model considering all parts from the generation of the heat at the plant to its consumption in the connected buildings so far. First, an exhaustive list of all dynamic phenomena occurring in district heating systems has been drawn and analyzed. Considering this list, this thesis proposes that a model which satisfies the criteria listed above can be developed by superposing four sub-models which are a dynamic model of the heat generation plant, a steady state model of the hydraulic calculation of the distribution network, a dynamic model of the thermal behavior of the network and a dynamic model of the heat consumers. The development of the four sub-models starts from the fundamental conservation equations for fluid systems, i.e. the conservation of mass, momentum and energy. The transformations of those general equations into simple calculation formulas show and justify the hypotheses made in the modeling process. The heat generation plant model itself is a set of sub-models: the models for steam boilers, hot water boilers and heat accumulators which take account of the dynamic evolution of the water temperature by a simple form of the energy conservation equation, as well as the steady state models for circulation pumps and pressurizers. Since the velocities in the network pipes are small, a consideration of steady states is adopted. A network model allowing to calculate the hydraulic variables in every point is adopted from the graph theory. The pressures and flow rates in the network are calculated at discrete time steps and they are considered to be constant for the duration between the time steps. (author) figs., tabs., refs

Analysis of the Nonlinear Static and Dynamic Behavior of Offshore Structures

KAUST Repository

Alfosail, Feras

2015-01-01

Understanding static and dynamic nonlinear behavior of pipes and risers is crucial for the design aspects in offshore engineering fields. In this work, we examine two nonlinear problems in offshore engineering field: vortex Induced vibration

Tungsten recrystallization and cracking under ITER-relevant heat loads

Energy Technology Data Exchange (ETDEWEB)

Budaev, V.P., E-mail: Budaev@mail.ru [NRC «Kurchatov Institute», Akademika Kurchatova pl., Moscow (Russian Federation); Martynenko, Yu.V. [NRC «Kurchatov Institute», Akademika Kurchatova pl., Moscow (Russian Federation); National Research Nuclear University MEPhI, Kashirskoe sh. 31, Moscow (Russian Federation); Karpov, A.V.; Belova, N.E. [NRC «Kurchatov Institute», Akademika Kurchatova pl., Moscow (Russian Federation); Zhitlukhin, A.M. [SRC RF TRINITI, Moscow Region (Russian Federation); Klimov, N.S., E-mail: klimov@triniti.ru [SRC RF TRINITI, Moscow Region (Russian Federation); National Research Nuclear University MEPhI, Kashirskoe sh. 31, Moscow (Russian Federation); Podkovyrov, V.L.; Barsuk, V.A.; Putrik, A.B.; Yaroshevskaya, A.D. [SRC RF TRINITI, Moscow Region (Russian Federation); Giniyatulin, R.N. [Efremov Institute, St. Petersburg (Russian Federation); Safronov, V.M. [Institution «Project Center ITER», Moscow (Russian Federation); SRC RF TRINITI, Moscow Region (Russian Federation); Khimchenko, L.N. [Institution «Project Center ITER», Moscow (Russian Federation)

2015-08-15

The tungsten surface structure was analyzed after the test in the QSPA-T under heat loads relevant to those expected in the ITER during disruptions. Repeated pulses lead to the melting and the resolidification of the tungsten surface layer of ∼50 μm thickness. There is ∼50 μm thickness intermediate layer between the original structure and the resolidified layer. The intermediate layer is recrystallized and has a random grains’ orientation whereas the resolidified layer and basic structure have texture with preferable orientation 〈1 0 0〉 normal to the surface. The cracks which were normal to the surface were observed in the resolidified layer as well as the cracks which were parallel to the surface at the depth up to 300 μm. Such cracks can result in the brittle destruction which is a hazard for the full tungsten divertor of the ITER. The theoretical analysis of the crack formation reasons and a possible consequence for the ITER are given.

Dynamic behavior of district heating systems. 1. Report

International Nuclear Information System (INIS)

Kunz, J.

1993-01-01

In this study a comprehensive model simulating the dynamic behavior of an entire district heating system has been developed. The model consists of four partial models, namely a model of the hydraulic behavior of a heat distribution network, another model of the thermal behavior of this network, a model of the heat generation plants and one of the heat consumers connected to the system. For the hydraulic simulation of the distribution network, a classical steady state approach has proved to be sufficient. The evolution of the temperatures in the network is given by the equation of transport. A numerical resolution scheme, which is adapted to the special case of a heat distribution network was developed for this equation. The model developed for the heating plant is simple but it is sufficiently detailed to determine the operation of its elements. A more complex model would take much more calculation time, but with such a simple model, it is possible to include it in the global model of the entire system. Each heat consumer is represented by a simple one cell model. The difficulty in such an approach is to determine the characteristics of each building in a simple manner. A classification, which allows to find the essential parameters from few and easily available data, has been defined. This model is not sufficiently accurate to calculate the thermal behavior of one specific building but it allows to determine the average dynamic evolution of the heat demand for a set of buildings with a good precision.The developed models have been programmed on a personal computer and the entire district heating network of the city of Lausanne has been simulated with this calculation code. Measurements have been taken on this network and the comparison with calculated results has allowed to calibrate the model. The comparison of measurements and calculations shows, that each part of the system is simulated realistically by the proposed model. (author) figs., tabs., refs

Mechanical behavior of ultrafine-grained materials under combined static and dynamic loadings

Directory of Open Access Journals (Sweden)

Guo Y.Z.

2015-01-01

Full Text Available Ultrafine-grained (UFG materials have extensive prospects for engineering application due to their excellent mechanical properties. However, the grain size decrease reduces their strain hardening ability and makes UFG materials more susceptible to deformation instability such as shear localization. In most cases, critical shear strain is taken as the criterion for formation of shear localization under impact loading or adiabatic shear band (ASB. Recently, some researchers found that the formation of ASB was determined only by the dynamic loading process and had nothing to do with its static loading history. They proposed for coarse-grained metals a dynamic stored energy-based criterion for ASB and verified it by some experiments. In this study, we will focus on the shear localization behavior of UFG metals such as UFG titanium and magnesium alloy AZ31. Quasi-static loading and dynamic loading will be applied on the same specimen alternately. The shear localization behavior will be analyzed and the criterion of its formation will be evaluated.

Strength and behavior in shear of reinforced concrete deep beams under dynamic loading conditions

Energy Technology Data Exchange (ETDEWEB)

Adhikary, Satadru Das [School of Civil and Environmental Engineering, Nanyang Technological University, 639798 (Singapore); Li, Bing, E-mail: cbli@ntu.edu.sg [School of Civil and Environmental Engineering, Nanyang Technological University, 639798 (Singapore); Fujikake, Kazunori [Department of Civil and Environmental Engineering, National Defense Academy, Yokosuka 239 8686 (Japan)

2013-06-15

Highlights: ► Effects of wider range of loading rates on dynamic shear behavior of RC deep beams. ► Experimental investigation of RC deep beam with and without shear reinforcements. ► Verification of experimental results with truss model and FE simulation results. ► Empirical equations are proposed to predict the dynamic increase factor of maximum resistance. -- Abstract: Research on reinforced concrete (RC) deep beams has seen considerable headway over the past three decades; however, information on the dynamic shear strength and behavior of RC deep beams under varying rates of loads remains limited. This paper describes the experimental results of 24 RC deep beams with and without shear reinforcements under varying rates of concentrated loading. Results obtained serve as useful data on shear resistance, failure patterns and strain rates corresponding to varying loading rates. An analytical truss model approach proves its efficacy in predicting the dynamic shear resistance under varying loading rates. Furthermore, three-dimensional nonlinear finite element (FE) model is described and the simulation results are verified with the experimental results. A parametric study is then conducted to investigate the influence of longitudinal reinforcement ratio, transverse reinforcement ratio and shear span to effective depth ratio on shear behavior. Subsequently, two empirical equations were proposed by integrating the various parameters to assess the dynamic increase factor (DIF) of maximum resistance under varying rates of concentrated loading.

Dynamic Behavior of Nanocomposites Reinforced with Multi-Walled Carbon Nanotubes (MWCNTs

Directory of Open Access Journals (Sweden)

Chun-Yu Lai

2013-06-01

Full Text Available The influence of multi-walled carbon nanotubes (MWCNT on the structural dynamic behavior of MWCNT/epoxy nanocomposites was investigated. Two different types of MWCNTs, pristine MWCNT and functionalized MWCNT, were used in this study. Carboxylic acid-functionalized MWCNTs (MWCNT-COOH were obtained by oxidation pristine MWCNTs via sonication in sulfuric-nitric acid and characterized by Fourier transform infrared spectroscopy (FTIR. Dynamic behaviors of the MWCNT reinforced nanocomposite including the natural frequency and damping ratio were determined using free vibration test. Experimental results showed that the damping ratio of the nanocomposite decreases with the increase of the MWCNT addition, while the natural frequency is increasing with the increase of the MWCNT addition. Functionalized MWCNTs improved the interfacial bonding between the nanotubes and epoxy resin resulting in the reduction of the interfacial energy dissipation ability and enhancement of the stiffness.

Understanding the heavy-tailed dynamics in human behavior

Science.gov (United States)

Ross, Gordon J.; Jones, Tim

2015-06-01

The recent availability of electronic data sets containing large volumes of communication data has made it possible to study human behavior on a larger scale than ever before. From this, it has been discovered that across a diverse range of data sets, the interevent times between consecutive communication events obey heavy-tailed power law dynamics. Explaining this has proved controversial, and two distinct hypotheses have emerged. The first holds that these power laws are fundamental, and arise from the mechanisms such as priority queuing that humans use to schedule tasks. The second holds that they are statistical artifacts which only occur in aggregated data when features such as circadian rhythms and burstiness are ignored. We use a large social media data set to test these hypotheses, and find that although models that incorporate circadian rhythms and burstiness do explain part of the observed heavy tails, there is residual unexplained heavy-tail behavior which suggests a more fundamental cause. Based on this, we develop a quantitative model of human behavior which improves on existing approaches and gives insight into the mechanisms underlying human interactions.

Secondary recrystallization in non-sag W filament wires -- On the possible role of relative grain boundary character distribution

International Nuclear Information System (INIS)

Samajdar, I.; Watte, P.; Mertens, F.

1999-01-01

Non-Sag tungsten (W) wire is indispensable for the lighting industry. For the necessary creep resistance, large elongated grains are considered as the desired microstructure. These large grains are obtained by primary and secondary recrystallization. In the present study an effort has been made to characterize and to understand the origin of such large elongated grains. In secondary recrystallization, often called abnormal grain growth, a few of the grains grow massive. The mechanisms of normal and abnormal grain growth are essentially the same, involving high angle boundary migration and driven by the reduction of surface energy. The abnormal grain growth can be visualized as a growth advantage for a few of the grains or growth disadvantage for the majority. Such an advantage/disadvantage may be caused by (1) differences in grain size and/or (2) differences in grain boundary character distribution (GBCD). In other words, a grain may grow massive if it has large size and/or possibilities of more favorable (i.e., of higher mobility) grain boundaries with the matrix grains

Dynamic behavior of cellular materials and cellular structures: Experiments and modeling

Science.gov (United States)

Gao, Ziyang

Cellular solids, including cellular materials and cellular structures (CMS), have attracted people's great interests because of their low densities and novel physical, mechanical, thermal, electrical and acoustic properties. They offer potential for lightweight structures, energy absorption, thermal management, etc. Therefore, the studies of cellular solids have become one of the hottest research fields nowadays. From energy absorption point of view, any plastically deformed structures can be divided into two types (called type I and type II), and the basic cells of the CMS may take the configurations of these two types of structures. Accordingly, separated discussions are presented in this thesis. First, a modified 1-D model is proposed and numerically solved for a typical type II structure. Good agreement is achieved with the previous experimental data, hence is used to simulate the dynamic behavior of a type II chain. Resulted from different load speeds, interesting collapse modes are observed, and the parameters which govern the cell's post-collapse behavior are identified through a comprehensive non-dimensional analysis on general cellular chains. Secondly, the MHS specimens are chosen as an example of type I foam materials because of their good uniformity of the cell geometry. An extensive experimental study was carried out, where more attention was paid to their responses to dynamic loadings. Great enhancement of the stress-strain curve was observed in dynamic cases, and the energy absorption capacity is found to be several times higher than that of the commercial metal foams. Based on the experimental study, finite elemental simulations and theoretical modeling are also conducted, achieving good agreements and demonstrating the validities of those models. It is believed that the experimental, numerical and analytical results obtained in the present study will certainly deepen the understanding of the unsolved fundamental issues on the mechanical behavior of

Analysis of the dynamic behavior and lubrication characteristics of a small reciprocating compressor

International Nuclear Information System (INIS)

Kim, Tae Jong

2003-01-01

In this paper, a study on the dynamic behavior and lubrication characteristics of a reciprocating compression mechanism used in small refrigeration compressor is performed. In the problem formulation of the compressor dynamics, the viscous frictional force between piston and cylinder wall is considered in order to determine the coupled dynamic behaviors of piston and crankshaft. The solutions of the equations of motion of the reciprocating mechanism along with the time dependent Reynolds equations for the lubricating film between piston and cylinder wall and oil films of the journal bearings are obtained simultaneously. The hydrodynamic forces of journal bearings are calculated using finite bearing model and Gumbel boundary condition. And, a Newton-Raphson procedure was employed in solving the nonlinear equations of piston and crankshaft. The results explored the effects of design parameters on the stability and lubrication characteristics of the compression mechanism

Evolving dynamics of trading behavior based on coordination game in complex networks

Science.gov (United States)

Bian, Yue-tang; Xu, Lu; Li, Jin-sheng

2016-05-01

This work concerns the modeling of evolvement of trading behavior in stock markets. Based on the assumption of the investors' limited rationality, the evolution mechanism of trading behavior is modeled according to the investment strategy of coordination game in network, that investors are prone to imitate their neighbors' activity through comprehensive analysis on the risk dominance degree of certain investment behavior, the network topology of their relationship and its heterogeneity. We investigate by mean-field analysis and extensive simulations the evolution of investors' trading behavior in various typical networks under different risk dominance degree of investment behavior. Our results indicate that the evolution of investors' behavior is affected by the network structure of stock market and the effect of risk dominance degree of investment behavior; the stability of equilibrium states of investors' behavior dynamics is directly related with the risk dominance degree of some behavior; connectivity and heterogeneity of the network plays an important role in the evolution of the investment behavior in stock market.

Evaluation of Dynamic Deformation Behaviors in Metallic Materials under High Strain-Rates Using Taylor Bar Impact Test

Energy Technology Data Exchange (ETDEWEB)

Bae, Kyung Oh; Shin, Hyung Seop [Andong National Univ., Andong (Korea, Republic of)

2016-09-15

To ensure the reliability and safety of various mechanical systems in accordance with their high-speed usage, it is necessary to evaluate the dynamic deformation behavior of structural materials under impact load. However, it is not easy to understand the dynamic deformation behavior of the structural materials using experimental methods in the high strain-rate range exceeding 10{sup 4} s{sup -1}. In this study, the Taylor bar impact test was conducted to investigate the dynamic deformation behavior of metallic materials in the high strain-rate region, using a high-speed photography system. Numerical analysis of the Taylor bar impact test was performed using AUTODYN S/W. The results of the analysis were compared with the experimental results, and the material behavior in the high strain-rate region was discussed.

Spent fuel's behavior under dynamic drip tests

International Nuclear Information System (INIS)

Finn, P.A.; Buck, E.C.; Hoh, J.C.; Bates, J.K.

1995-01-01

In the potential repository at Yucca Mountain, failure of the waste package container and the cladding of the spent nuclear fuel would expose the fuel to water under oxidizing conditions. To simulate the release behavior of radionuclides from spent fuel, dynamic drip and vapor tests with spent nuclear fuel have been ongoing for 2.5 years. Rapid alteration of the spent fuel has been noted with concurrent release of radionuclides. Colloidal species containing americium and plutonium have been found in the leachate. This observation suggests that colloidal transport of radionuclides should be included in the performance assessment of a potential repository

Strain and strain-rate hardening characteristics of a superplastic Al-Li-Cu-Zr alloy

International Nuclear Information System (INIS)

Ash, B.A.; Hamilton, C.H.

1988-01-01

A number of alloys based on the composition of Al-Li-Zr have been shown to be superplastic under at least one of two different microstructural conditions: 1. fully recrystallized to a fine, stable grain size, and 2. warm- or cold-worked and unrecrystallized prior to superplastic deformation. For the latter case, static recrystallization was impaired by the presence of fine Al 3 Zr particles, and dynamic recrystallization was observed to occur during superplastic deformation in which the heavily worked microstructure evolved into a fine grained fully recrystallized microstructure. This process is observed in other Al alloys as well, such as the Al-Cu-Zr alloys (Supral alloys), Al-Zn-Mg-Zr alloys, Al-Mn-Zr alloys, and Al-Mg-Mn alloys where the dynamic recrystallization has been suggested to be a continuous reaction in which recrystallization occurs by a gradual and homogeneous process during deformation rather than by the more common nucleation and growth process. Experimental observations of continuous recrystallization show development of a subgrain structure which coarsens continuously while deformation proceeds, with a concurrent increase in the misorientation angle between adjacent subgrains which ultimately approaches that of a high-angle boundary, characteristic of a fully- recrystallized microstructure. During the first 50 to 300% deformation, the microstructure evolves from the heavily worked to a fully recrystallized microstructure after which the fully recrystallized microstructure apparently exhibits the typical micro-grain superplastic characteristics. Superplasticity under continuous dynamic recrystallization is of interest both from scientific and technological standpoints since the rates at which superplastic deformation can be obtained are often higher than those for the fully recrystallized microstructures

Microstructure Evolution and Surface Cracking Behavior of Superheavy Forgings during Hot Forging

Directory of Open Access Journals (Sweden)

Zhenhua Wang

2018-01-01

Full Text Available In recent years, superheavy forgings that are manufactured from 600 t grade ingots have been applied in the latest generation of nuclear power plants to provide good safety. However, component production is pushing the limits of the current free-forging industry. Large initial grain sizes and a low strain rate are the main factors that contribute to the deformation of superheavy forgings during forging. In this study, 18Mn18Cr0.6N steel with a coarse grain structure was selected as a model material. Hot compression and hot tension tests were conducted at a strain rate of 10−4·s−1. The essential nucleation mechanism of the dynamic recrystallization involved low-angle grain boundary formation and subgrain rotation, which was independent of the original high-angle grain boundary bulging and the presence of twins. Twins were formed during the growth of dynamic recrystallization grains. The grain refinement was not obvious at 1150°C. A lowering of the deformation temperature to 1050°C resulted in a fine grain structure; however, the stress increased significantly. Crack-propagation paths included high-angle grain boundaries, twin boundaries, and the insides of grains, in that order. For superheavy forging, the ingot should have a larger height and a smaller diameter.

Ice recrystallization inhibition in ice cream as affected by ice structuring proteins from winter wheat grass.

Science.gov (United States)

Regand, A; Goff, H D

2006-01-01

Ice recrystallization in quiescently frozen sucrose solutions that contained some of the ingredients commonly found in ice cream and in ice cream manufactured under commercial conditions, with or without ice structuring proteins (ISP) from cold-acclimated winter wheat grass extract (AWWE), was assessed by bright field microscopy. In sucrose solutions, critical differences in moisture content, viscosity, ionic strength, and other properties derived from the presence of other ingredients (skim milk powder, corn syrup solids, locust bean gum) caused a reduction in ice crystal growth. Significant ISP activity in retarding ice crystal growth was observed in all solutions (44% for the most complex mix) containing 0.13% total protein from AWWE. In heat-shocked ice cream, ice recrystallization rates were significantly reduced 40 and 46% with the addition of 0.0025 and 0.0037% total protein from AWWE. The ISP activity in ice cream was not hindered by its inclusion in mix prior to pasteurization. A synergistic effect between ISP and stabilizer was observed, as ISP activity was reduced in the absence of stabilizer in ice cream formulations. A remarkably smoother texture for ice creams containing ISP after heat-shock storage was evident by sensory evaluation. The efficiency of ISP from AWWE in controlling ice crystal growth in ice cream has been demonstrated.

Oman Drilling Project GT3 site survey: dynamics at the roof of an oceanic magma chamber

Science.gov (United States)

France, L.; Nicollet, C.; Debret, B.; Lombard, M.; Berthod, C.; Ildefonse, B.; Koepke, J.

2017-12-01

Oman Drilling Project (OmanDP) aims at bringing new constraints on oceanic crust accretion and evolution by drilling Holes in the whole ophiolite section (mantle and crust). Among those, operations at GT3 in the Sumail massif drilled 400 m to sample the dike - gabbro transition that corresponds to the top (gabbros) and roof (dikes) of the axial magma chamber, an interface where hydrothermal and magmatic system interacts. Previous studies based on oceanic crust formed at present day fast-spreading ridges and preserved in ophiolites have highlighted that this interface is a dynamic horizon where the axial melt lens that top the main magma chamber can intrude, reheat, and partially assimilate previously hydrothermally altered roof rocks. Here we present the preliminary results obtained in GT3 area that have allowed the community to choose the drilling site. We provide a geological and structural map of the area, together with new petrographic and chemical constraints on the dynamics of the dike - gabbro transition. Our new results allow us to quantify the dynamic processes, and to propose that 1/ the intrusive contact of the varitextured gabbro within the dikes highlights the intrusion of the melt lens top in the dike rooting zone, 2/ both dikes and previously crystallized gabbros are reheated, and recrystallized by underlying melt lens dynamics (up to 1050°C, largely above the hydrous solidus temperature of altered dikes and gabbros), 3/ the reheating range can be > 200°C, 4/ the melt lens depth variations for a given ridge position is > 200m, 5/ the reheating stage and associated recrystallization within the dikes occurred under hydrous conditions, 6/ the reheating stage is recorded at the root zone of the sheeted dike complex by one of the highest stable conductive thermal gradient ever recorded on Earth ( 3°C/m), 7/ local chemical variations in recrystallized dikes and gabbros are highlighted and used to quantify crystallization and anatectic processes, and the

Dynamical Behavior of a Pseudoelastic Vibration Absorber Using Shape Memory Alloys

Directory of Open Access Journals (Sweden)

Hugo De S. Oliveira

2017-01-01

Full Text Available The tuned vibration absorber (TVA provides vibration reduction of a primary system subjected to external excitation. The idea is to increase the number of system degrees of freedom connecting a secondary system to the primary system. This procedure promotes vibration reduction at its design forcing frequency but two new resonance peaks appear introducing critical behaviors that must be avoided. The use of shape memory alloys (SMAs can improve the performance of the classical TVA establishing an adaptive TVA (ATVA. This paper deals with the nonlinear dynamics of a passive pseudoelastic tuned vibration absorber with an SMA element. In this regard, a single degree of freedom elastic oscillator is used to represent the primary system, while an extra oscillator with an SMA element represents the secondary system. Temperature dependent behavior of the system allows one to change the system response avoiding undesirable responses. Nevertheless, hysteretic behavior introduces complex characteristics to the system dynamics. The influence of the hysteretic behavior due to stress-induced phase transformation is investigated. The ATVA performance is evaluated by analyzing primary system maximum vibration amplitudes for different forcing amplitudes and frequencies. Numerical simulations establish comparisons of the ATVA results with those obtained from the classical TVA. A parametric study is developed showing the best performance conditions and this information can be useful for design purposes.

Properties and recrystallization of radiation damaged pyrochlore and titanite

Energy Technology Data Exchange (ETDEWEB)

Zietlow, Peter

2016-11-02

Radiation damage in minerals is caused by the alpha-decay of incorporated radionuclides, such as U and Th and their decay products. The effect of thermal annealing (400-1400 K) on radiation-damaged pyrochlores has been investigated by Raman scattering, X-ray powder diffraction (XRD), and combined differential scanning calorimetry/thermogravimetry (DSC/TG) (Zietlow et al., in print). The analysis of three natural radiation-damaged pyrochlore samples from Miass/Russia (6.4 wt% Th, 23.1.10{sup 18} a-decay events per gram (dpg)), Zlatoust/Russia (6.3 wt% Th, 23.1.10{sup 18} dpg), Panda Hill/Tanzania (1.6 wt% Th, 1.6.10{sup 18} dpg), and Blue River/Canada (10.5 wt% U, 115.4.10{sup 18} dpg), are compared with a crystalline reference pyrochlore from Schelingen (Germany). The type of structural recovery depends on the initial degree of radiation damage (Panda Hill 28 %, Blue River 85 %, Zlatoust and Miass 100 % according to XRD), as the recrystallization temperature increases with increasing degree of amorphization. Raman spectra indicate reordering on the local scale during annealing-induced recrystallization. As Raman modes around 800 cm{sup -1} are sensitive to radiation damage (Vandenborre and Husson 1983, Moll et al. 2011), the degree of local order was deduced from the ratio of the integrated intensities of the sum of the Raman bands between 605 and 680 cm{sup -1} devided by the sum of the integrated intensities of the bands between 810 and 860 cm{sup -1}. The most radiation damaged pyrochlores (Miass and Zlatoust) show an abrupt recovery of both, its short- (Raman) and long-range order (X-ray) between 800 and 850 K. The volume decrease upon recrystallization in Zlatoust pyrochlore was large enough to crack the sample repeatedly. In contrast, the weakly damaged pyrochlore (Panda Hill) begins to recover at considerably lower temperatures (near 500 K), extending over a temperature range of ca. 300 K, up to 800 K (Raman). The pyrochlore from Blue River shows in its

The effect of stress tolerance on dynamics of activity-travel behavior : numerical simulation results

NARCIS (Netherlands)

Psarra, I.; Arentze, T.A.; Timmermans, H.J.P.

2014-01-01

The primary and secondary effects of various spatial and transportation policies can be evaluated with models of activity–travel behavior. Whereas existing activity-based models of travel demand simulate a typical day, dynamic models simulate behavioral response to endogenous or exogenous change,

Dynamic hysteresis behaviors for the two-dimensional mixed spin (2, 5/2) ferrimagnetic Ising model in an oscillating magnetic field

Science.gov (United States)

Ertaş, Mehmet

2015-09-01

Keskin and Ertaş (2009) presented a study of the magnetic properties of a mixed spin (2, 5/2) ferrimagnetic Ising model within an oscillating magnetic field. They employed dynamic mean-field calculations to find the dynamic phase transition temperatures, the dynamic compensation points of the model and to present the dynamic phase diagrams. In this work, we extend the study and investigate the dynamic hysteresis behaviors for the two-dimensional (2D) mixed spin (2, 5/2) ferrimagnetic Ising model on a hexagonal lattice in an oscillating magnetic field within the framework of dynamic mean-field calculations. The dynamic hysteresis curves are obtained for both the ferromagnetic and antiferromagnetic interactions and the effects of the Hamiltonian parameters on the dynamic hysteresis behaviors are discussed in detail. The thermal behaviors of the coercivity and remanent magnetizations are also investigated. The results are compared with some theoretical and experimental works and a qualitatively good agreement is found. Finally, the dynamic phase diagrams depending on the frequency of an oscillating magnetic field in the plane of the reduced temperature versus magnetic field amplitude is examined and it is found that the dynamic phase diagrams display richer dynamic critical behavior for higher values of frequency than for lower values.

Dynamic behaviors of spin-1/2 bilayer system within Glauber-type stochastic dynamics based on the effective-field theory

International Nuclear Information System (INIS)

Ertaş, Mehmet; Kantar, Ersin; Keskin, Mustafa

2014-01-01

The dynamic phase transitions (DPTs) and dynamic phase diagrams of the kinetic spin-1/2 bilayer system in the presence of a time-dependent oscillating external magnetic field are studied by using Glauber-type stochastic dynamics based on the effective-field theory with correlations for the ferromagnetic/ferromagnetic (FM/FM), antiferromagnetic/ferromagnetic (AFM/FM) and antiferromagnetic/antiferromagnetic (AFM/AFM) interactions. The time variations of average magnetizations and the temperature dependence of the dynamic magnetizations are investigated. The dynamic phase diagrams for the amplitude of the oscillating field versus temperature were presented. The results are compared with the results of the same system within Glauber-type stochastic dynamics based on the mean-field theory. - Highlights: • The Ising bilayer system is investigated within the Glauber dynamics based on EFT. • The time variations of average order parameters to find phases are studied. • The dynamic phase diagrams are found for the different interaction parameters. • The system displays the critical points as well as a re-entrant behavior

Dynamic behaviors of spin-1/2 bilayer system within Glauber-type stochastic dynamics based on the effective-field theory

Energy Technology Data Exchange (ETDEWEB)

Ertaş, Mehmet; Kantar, Ersin, E-mail: ersinkantar@erciyes.edu.tr; Keskin, Mustafa

2014-05-01

The dynamic phase transitions (DPTs) and dynamic phase diagrams of the kinetic spin-1/2 bilayer system in the presence of a time-dependent oscillating external magnetic field are studied by using Glauber-type stochastic dynamics based on the effective-field theory with correlations for the ferromagnetic/ferromagnetic (FM/FM), antiferromagnetic/ferromagnetic (AFM/FM) and antiferromagnetic/antiferromagnetic (AFM/AFM) interactions. The time variations of average magnetizations and the temperature dependence of the dynamic magnetizations are investigated. The dynamic phase diagrams for the amplitude of the oscillating field versus temperature were presented. The results are compared with the results of the same system within Glauber-type stochastic dynamics based on the mean-field theory. - Highlights: • The Ising bilayer system is investigated within the Glauber dynamics based on EFT. • The time variations of average order parameters to find phases are studied. • The dynamic phase diagrams are found for the different interaction parameters. • The system displays the critical points as well as a re-entrant behavior.

Variation in predator foraging behavior changes predator-prey spatio-temporal dynamics

Science.gov (United States)

1. Foraging underlies the ability of all animals to acquire essential resources and, thus, provides a critical link to understanding population dynamics. A key issue is how variation in foraging behavior affects foraging efficiency and predator-prey interactions in spatially-heterogeneous environmen...

Ice recrystallization inhibition in ice cream by propylene glycol monostearate.

Science.gov (United States)

Aleong, J M; Frochot, S; Goff, H D

2008-11-01

The effectiveness of propylene glycol monostearate (PGMS) to inhibit ice recrystallization was evaluated in ice cream and frozen sucrose solutions. PGMS (0.3%) dramatically reduced ice crystal sizes in ice cream and in sucrose solutions frozen in a scraped-surface freezer before and after heat shock, but had no effect in quiescently frozen solutions. PGMS showed limited emulsifier properties by promoting smaller fat globule size distributions and enhanced partial coalescence in the mix and ice cream, respectively, but at a much lower level compared to conventional ice cream emulsifier. Low temperature scanning electron microscopy revealed highly irregular crystal morphology in both ice cream and sucrose solutions frozen in a scraped-surface freezer. There was strong evidence to suggest that PGMS directly interacts with ice crystals and interferes with normal surface propagation. Shear during freezing may be required for its distribution around the ice and sufficient surface coverage.

Shock compression of a recrystallized anorthositic rock from Apollo 15

Science.gov (United States)

Ahrens, T. J.; Gibbons, R. V.; O'Keefe, J. D.

1973-01-01

Hugoniot measurements on 15,418, a recrystallized and brecciated gabbroic anorthosite, yield a value of the Hugoniot elastic limit (HEL) varying from 45 to 70 kbar as the final shock pressure is varied from 70 to 280 kbar. Above the HEL and to 150 kbar, the pressure-density Hugoniot is closely described by a hydrostatic equation of state constructed from ultrasonic data for single-crystal plagioclase and pyroxene. Above 150 kbar, the Hugoniot states indicate that a series of one or more shock-induced phase changes are occurring in the plagioclase and pyroxene. From Hugoniot data for both the single-crystal minerals and the Frederick diabase, we infer that the shock-induced high-pressure phases in 15,418 probably consists of a 3.71 g/cu cm density, high-pressure structure for plagioclase and a 4.70 g/cu cm perovskite-type structure for pyroxene.

Influence of Temperature on Mechanical Behavior During Static Restore Processes of Al-Zn-Mg-Cu High Strength Aluminum Alloy

Directory of Open Access Journals (Sweden)

ZHANG Kun

2017-06-01

Full Text Available Flow stress behaviors of as-cast Al-Zn-Mg-Cu high strength aluminum alloy during static restore processes were investigated by: Isothermal double-pass compression tests at temperatures of 300-400℃, strain rates of 0.01-1 s-1, strains of 33% +20% with the holding times of 0~900 s after the first pass compression. The results indicate that the deformation temperature has a dramatical effect on mechanical behaviors during static restore processes of the alloy. (1 At 300 ℃ and 330 ℃ lower temperatures, the recovery during the deformation is slow, and deformation energy stored in matrix is higher, flow stresses at the second pass deformation decreased during the recovery and recrystallization, and the stress softening phenomena is observed. Stress softening is increased with the increasing holding time; Precipitation during the holding time inhibites the stress softening. (2 At 360 ℃ and 400 ℃ higher temperatures, the recovery during deformation is rapid, and deformation energy stored in matrix is lower. Solid solubility is higher after holding, so that flow stress at the second pass deformation is increased, stress hardening phenomena is observed. Stress hardening decreased with the increasing holding time duo to the recovery and recrystallization during holding period at 360 ℃; Precipitation during holding also inhibited the stress softening. However, Stress hardening remains constant with the increasing holding time duo to the reasanenal there are no recovery and recrystallization during holding period at 400 ℃.

Dynamic behavior of IREB in a collective ion acceleration experiment

International Nuclear Information System (INIS)

Fine, T.A.; Rhee, M.J.

1989-01-01

The authors report an experimental study of dynamic behavior of net current in conjunction with collective ion acceleration. In the presence of neutral gas, either puffed in or released from the anode foil, the IREB injected is subject to the charge and current neutralizations, resulting in a complicated time and space dependent beam distribution in the drift tube. To investigate the dynamic behavior of the current in the drift tube, typically a 0.5 MeV, 70 kA, 100 ns electron beam of 2.54 cm diam is injected through a foil anode into a drift tube of 15 cm diam. Reproducibility of experiment was improved by using a specially designed anode system with a foil changer which allowed the production of many shots of high current electron beam without disturbing the vacuum condition. The net currents were measured by a Rogowski coil built in the anode system, and a movable Faraday cup along the drift tube. The ions accelerated were diagnosed mainly by a Thomson spectrometer system placed at the end of the drift tube

Dynamic power behavior of a PWR type nuclear reactor

International Nuclear Information System (INIS)

Moreira, F.J.

1984-01-01

A methodology for the power level evaluation (dynamic behavior) in a Pressurized Water Reactor, during a transient is developed, by solving the point kinetic equation related to the control rod insertion effects and fuel or moderator temperature 'feed-back'. A new version of the thermal-hydraulic code COBRA III P/MIT, is used. In this new version was included, as an option, the methodology developed. (E.G.) [pt

Phase transitions, nonequilibrium dynamics, and critical behavior of strongly interacting systems

International Nuclear Information System (INIS)

Mottola, E.; Bhattacharya, T.; Cooper, F.

1998-01-01

This is the final report of a three-year, Laboratory Directed Research and Development project at Los Alamos National Laboratory. In this effort, large-scale simulations of strongly interacting systems were performed and a variety of approaches to the nonequilibrium dynamics of phase transitions and critical behavior were investigated. Focus areas included (1) the finite-temperature quantum chromodynamics phase transition and nonequilibrium dynamics of a new phase of matter (the quark-gluon plasma) above the critical temperature, (2) nonequilibrium dynamics of a quantum fields using mean field theory, and (3) stochastic classical field theoretic models with applications to spinodal decomposition and structural phase transitions in a variety of systems, such as spin chains and shape memory alloys

Predicting dynamic behavior via anticipating synchronization in coupled pendulum-like systems

International Nuclear Information System (INIS)

Xu Shiyun; Yang Ying

2009-01-01

In this paper, the regime of anticipating synchronization (sometimes called predicted synchronization) in a class of nonlinear dynamical systems is investigated by testing the global asymptotical stability of time-delayed error dynamics. Sufficient conditions in terms of linear matrix inequalities are established for anticipating synchronization between such systems with and without state time delay. These results allow one to predict the dynamic behavior of the systems by using a copy of the same system that performs as a slave. Moreover, the cascaded anticipating synchronization is concerned such that several slave systems could anticipate the same master system with different delays. Concrete applications to phase-locked loops demonstrate the applicability and validity of the proposed results.

Phase transitions, nonequilibrium dynamics, and critical behavior of strongly interacting systems

Energy Technology Data Exchange (ETDEWEB)

Mottola, E.; Bhattacharya, T.; Cooper, F. [and others

1998-12-31

This is the final report of a three-year, Laboratory Directed Research and Development project at Los Alamos National Laboratory. In this effort, large-scale simulations of strongly interacting systems were performed and a variety of approaches to the nonequilibrium dynamics of phase transitions and critical behavior were investigated. Focus areas included (1) the finite-temperature quantum chromodynamics phase transition and nonequilibrium dynamics of a new phase of matter (the quark-gluon plasma) above the critical temperature, (2) nonequilibrium dynamics of a quantum fields using mean field theory, and (3) stochastic classical field theoretic models with applications to spinodal decomposition and structural phase transitions in a variety of systems, such as spin chains and shape memory alloys.

Microstructures and mechanical behavior of magnesium processed by ECAP at ice-water temperature

Science.gov (United States)

Zuo, Dai; Li, Taotao; Liang, Wei; Wen, Xiyu; Yang, Fuqian

2018-05-01

Magnesium of high purity is processed by equal channel angular pressing (ECAP) up to eight passes at the ice-water temperature, in which a core–shell-like structure is used. The core–shell-like structure consists of pure iron (Fe) of 1.5 mm in thickness as the shell and magnesium (Mg) as the core. The microstructure, texture and mechanical behavior of the ECAP-processed Mg are studied. The ECAP processing leads to the formation of fine and equiaxed grains of ~1.1 µm. The basal planes initially parallel to the extrusion direction evolve to slanted basal planes with the tilting angle in a range of 25°–45° to the extrusion direction. Increasing the number of the extrusion passes leads to the decreasing of twins and dislocation density in grains, while individual grains after eight passes still have high dislocation density. The large decreases of twins and the dislocation density make dynamic recrystallization (DRX) difficult, resulting in the decrease of the degree of DRX. Tension test reveals that the mechanical behavior of the ECAP-processed Mg is dependent on grain refinement and textures. The yield strength of the ECAP-extruded Mg first increases with the decrease of the grain size, and then decreases with further decrease of the grain size.

A study of dynamical behavior of space environment

Science.gov (United States)

Wu, S. T.

1974-01-01

Studies have covered a wide range of problems in the space environment, such as the problems of the dynamical behavior of the thermosphere, hydromagnetic wave propagation in the ionosphere, and interplanetary space environment. The theories used to analyze these problems range from a continuum theory of magnetohydrodynamics to the kinetic theory of free molecular flow. This is because the problems encountered covered the entire range of the Knudsen number (i.e., the ratio of mean free path to the characteristic length). Significant results are summarized.

Poverty dynamics in Germany: Evidence on the relationship between persistent poverty and health behavior.

Science.gov (United States)

Aue, Katja; Roosen, Jutta; Jensen, Helen H

2016-03-01

Previous studies have found poverty to be related to lower levels of health due to poor health behavior such as unhealthy eating, smoking or less physical activity. Longer periods of poverty seem to be especially harmful for individual health behavior. Studies have shown that poverty has a dynamic character. Moreover, poverty is increasingly regarded as being a multidimensional construct and one that considers more aspects than income alone. Against this background this paper analyzes the relationship between health behavior and persistent spells of income poverty as well as a combined poverty indicator using data of the German Socio-Economic Panel (2000-2010). Next to cross-sectional logistic regression models we estimate fixed-effects models to analyze the effect of persistent poverty on dietary behavior, tobacco consumption, and physical activity. Cross-sectional results suggest that persistent poverty is related to poor health behavior, particularly regarding tobacco consumption and physical activity. Results also show that multidimensional and dynamic aspects of poverty matter. Complementary panel analyses reveal negative effects for the combined poverty indicator only for dietary behavior in the total sample. However, by analyzing the sample by gender we identify further effects of persistent poverty on health behavior. The analyses show that not only do individuals in poverty but also those in precarious situations show health-damaging behavior more often. Copyright © 2016 Elsevier Ltd. All rights reserved.

Constitutive law for thermally-activated plasticity of recrystallized tungsten

Science.gov (United States)

Zinovev, Aleksandr; Terentyev, Dmitry; Dubinko, Andrii; Delannay, Laurent

2017-12-01

A physically-based constitutive law relevant for ITER-specification tungsten grade in as-recrystallized state is proposed. The material demonstrates stages III and IV of the plastic deformation, in which hardening rate does not drop to zero with the increase of applied stress. Despite the classical Kocks-Mecking model, valid at stage III, the strain hardening asymptotically decreases resembling a hyperbolic function. The material parameters are fitted by relying on tensile test data and by requiring that the strain and stress at the onset of diffuse necking (uniform elongation and ultimate tensile strength correspondingly) as well as the yield stress be reproduced. The model is then validated in the temperature range 300-600 °C with the help of finite element analysis of tensile tests which confirms the reproducibility of the experimental engineering curves up to the onset of diffuse necking, beyond which the development of ductile damage accelerates the material failure. This temperature range represents the low temperature application window for tungsten as divertor material in fusion reactor ITER.

Nonlinear Dynamic Behavior of a Bi-Axial Torsional MEMS Mirror with Sidewall Electrodes

Directory of Open Access Journals (Sweden)

Mehmet Ozdogan

2016-03-01

Full Text Available Nonlinear dynamic responses of a Micro-Electro-Mechanical Systems (MEMS mirror with sidewall electrodes are presented that are in close agreement with previously-reported experimental data. An analysis of frequency responses reveals softening behavior, and secondary resonances originated from the dominant quadratic nonlinearity. The quadratic nonlinearity is an electromechanical coupling effect caused by the electrostatic force. This effect is reflected in our mathematical model used to simulate the dynamic response of the micro-mirror. The effects of increased forcing and decreased damping on the frequency response are investigated as the mirrors are mostly used in vacuum packages. The results can predict MEMS mirror behaviors in optical devices better than previously-reported models.

Simulation of Missing Pellet Surface thermal behavior with 3D dynamic gap element

International Nuclear Information System (INIS)

Kim, Hyo Chan; Yang, Yong Sik; Koo, Yang Hyun; Kang, Chang Hak; Lee Sung Uk; Yang, Dong Yol

2014-01-01

Most of the fuel performance codes that are able to simulate a multidimensional analysis are used to calculate the radial temperature distribution and perform a multidimensional mechanical analysis based on a one-dimensional (1D) temperature result. The FRAPCON-FRAPTRAN code system incorporates a 1D thermal module and two-dimensional (2D) mechanical module when FEM option is activated. In this method, the multidimensional gap conductance model is not required because one-dimensional thermal analysis is carried out. On the other hand, a gap conductance model for a multi-dimension should be developed in the code to perform a multidimensional thermal analysis. ALCYONE developed by CEA introduces an equivalent heat convection coefficient that represents the multidimensional gap conductance. However, the code does not employ dynamic gap conductance which is a function of gap thickness and gap characteristics in direct. The BISON code, which has been developed by INL (Idaho National Laboratory), employed a thermo-mechanical contact method that is specifically designed for tightly-coupled implicit solutions that employ Jacobian-free solution methods. Owing to tightly-coupled implicit solutions, the BISON code solves gap conductance and gap thickness simultaneously with given boundary conditions. In this paper, 3D dynamic gap element has been proposed to resolve convergence issue and nonlinear characteristic of multidimensional gap conductance. To evaluate 3D dynamic gap element module, 3D thermomechanical module using FORTRAN77 has been implemented incorporating 3D dynamic gap element. To demonstrate effect of 3D dynamic gap element, thermal behavior of missing pellet surface (MPS) has been simulated by the developed module. LWR fuel performance codes should incorporate thermo-mechanical loop to solve gap conductance problem, iteratively. However, gap conductance in multidimensional model is difficult issue owing to its nonlinearity and convergence characteristics. In

The Effect of Prestrain Temperature on Kinetics of Static Recrystallization, Microstructure Evolution, and Mechanical Properties of Low Carbon Steel

Science.gov (United States)

Akbari, Edris; Karimi Taheri, Kourosh; Karimi Taheri, Ali

2018-05-01

In this research, the samples of a low carbon steel sheet were rolled up to a thickness prestrain of 67% at three different temperatures consisted of room, blue brittleness, and subzero temperature. Microhardness, SEM, and tensile tests were carried out to evaluate the static recrystallization kinetics defined by the Avrami equation, microstructural evolution, and mechanical properties. It was found that the Avrami exponent is altered with change in prestrain temperature and it achieves the value of 1 to 1. 5. Moreover, it was indicated that prestraining at subzero temperature followed by annealing at 600 °C leads to considerable enhancement in tensile properties and kinetics of static recrystallization compared to room and blue brittleness temperatures. The prestraining at blue brittleness temperature followed by annealing treatment caused, however, a higher strength and faster kinetics compared with that at room temperature. It was concluded that although from the steel ductility point of view, the blue brittleness temperature is called an unsuitable temperature, but it can be used as prestraining temperature to develop noticeable combination of strength and ductility in low carbon steel.

Entropy Maximization as a Basis for Information Recovery in Dynamic Economic Behavioral Systems

Directory of Open Access Journals (Sweden)

George Judge

2015-02-01

Full Text Available As a basis for information recovery in open dynamic microeconomic systems, we emphasize the connection between adaptive intelligent behavior, causal entropy maximization and self-organized equilibrium seeking behavior. This entropy-based causal adaptive behavior framework permits the use of information-theoretic methods as a solution basis for the resulting pure and stochastic inverse economic-econometric problems. We cast the information recovery problem in the form of a binary network and suggest information-theoretic methods to recover estimates of the unknown binary behavioral parameters without explicitly sampling the configuration-arrangement of the sample space.

A physically-based constitutive model for SA508-III steel: Modeling and experimental verification

International Nuclear Information System (INIS)

Dong, Dingqian; Chen, Fei; Cui, Zhenshan

2015-01-01

Due to its good toughness and high weldability, SA508-III steel has been widely used in the components manufacturing of reactor pressure vessels (RPV) and steam generators (SG). In this study, the hot deformation behaviors of SA508-III steel are investigated by isothermal hot compression tests with forming temperature of (950–1250)°C and strain rate of (0.001–0.1)s −1 , and the corresponding flow stress curves are obtained. According to the experimental results, quantitative analysis of work hardening and dynamic softening behaviors is presented. The critical stress and critical strain for initiation of dynamic recrystallization are calculated by setting the second derivative of the third order polynomial. Based on the classical stress–dislocation relation and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of SA508-III steel. Comparisons between the predicted and measured flow stress indicate that the established physically-based constitutive model can accurately characterize the hot deformations for the steel. Furthermore, a successful numerical simulation of the industrial upsetting process is carried out by implementing the developed constitutive model into a commercial software, which evidences that the physically-based constitutive model is practical and promising to promote industrial forging process for nuclear components

A physically-based constitutive model for SA508-III steel: Modeling and experimental verification

Energy Technology Data Exchange (ETDEWEB)

Dong, Dingqian [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China); Chen, Fei, E-mail: feechn@gmail.com [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China); Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Cui, Zhenshan, E-mail: cuizs@sjtu.edu.cn [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China)

2015-05-14

Due to its good toughness and high weldability, SA508-III steel has been widely used in the components manufacturing of reactor pressure vessels (RPV) and steam generators (SG). In this study, the hot deformation behaviors of SA508-III steel are investigated by isothermal hot compression tests with forming temperature of (950–1250)°C and strain rate of (0.001–0.1)s{sup −1}, and the corresponding flow stress curves are obtained. According to the experimental results, quantitative analysis of work hardening and dynamic softening behaviors is presented. The critical stress and critical strain for initiation of dynamic recrystallization are calculated by setting the second derivative of the third order polynomial. Based on the classical stress–dislocation relation and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of SA508-III steel. Comparisons between the predicted and measured flow stress indicate that the established physically-based constitutive model can accurately characterize the hot deformations for the steel. Furthermore, a successful numerical simulation of the industrial upsetting process is carried out by implementing the developed constitutive model into a commercial software, which evidences that the physically-based constitutive model is practical and promising to promote industrial forging process for nuclear components.

Model and Dynamic Behavior of Malware Propagation over Wireless Sensor Networks

Science.gov (United States)

Song, Yurong; Jiang, Guo-Ping

Based on the inherent characteristics of wireless sensor networks (WSN), the dynamic behavior of malware propagation in flat WSN is analyzed and investigated. A new model is proposed using 2-D cellular automata (CA), which extends the traditional definition of CA and establishes whole transition rules for malware propagation in WSN. Meanwhile, the validations of the model are proved through theoretical analysis and simulations. The theoretical analysis yields closed-form expressions which show good agreement with the simulation results of the proposed model. It is shown that the malware propaga-tion in WSN unfolds neighborhood saturation, which dominates the effects of increasing infectivity and limits the spread of the malware. MAC mechanism of wireless sensor networks greatly slows down the speed of malware propagation and reduces the risk of large-scale malware prevalence in these networks. The proposed model can describe accurately the dynamic behavior of malware propagation over WSN, which can be applied in developing robust and efficient defense system on WSN.

Constitutive Equation and Hot Compression Deformation Behavior of Homogenized Al–7.5Zn–1.5Mg–0.2Cu–0.2Zr Alloy

Directory of Open Access Journals (Sweden)

Jianliang He

2017-10-01

Full Text Available The deformation behavior of homogenized Al–7.5Zn–1.5Mg–0.2Cu–0.2Zr alloy has been studied by a set of isothermal hot compression tests, which were carried out over the temperature ranging from 350 °C to 450 °C and the strain rate ranging from 0.001 s−1 to 10 s−1 on Gleeble-3500 thermal simulation machine. The associated microstructure was studied using electron back scattered diffraction (EBSD and transmission electron microscopy (TEM. The results showed that the flow stress is sensitive to strain rate and deformation temperature. The shape of true stress-strain curves obtained at a low strain rate (≤0.1 s−1 conditions shows the characteristic of dynamic recrystallization (DRX. Two Arrhenius-typed constitutive equation without and with strain compensation were established based on the true stress-strain curves. Constitutive equation with strain compensation has more precise predictability. The main softening mechanism of the studied alloy is dynamic recovery (DRV accompanied with DRX, particularly at deformation conditions, with low Zener-Holloman parameters.

Effect of sputtering on self-damaged recrystallized W mirror specimens

Energy Technology Data Exchange (ETDEWEB)

Voitsenya, V.S. [Institute of Plasma Physics, National Scientific Center “KIPT”, 61108 Kharkov (Ukraine); Balden, M. [Max-Planck-Institut für Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Belyaeva, A.I. [National Technical University, “Kharkiv Polytechnical Institute”, 61002 Kharkov (Ukraine); Alimov, V.Kh. [Hydrogen Isotope Research Center, University of Toyama, Toyama 930-8555 (Japan); Tyburska-Püschel, B., E-mail: tyburska@engr.wisc.edu [Max-Planck-Institut für Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Galuza, A.A. [Institute of Electrophysics and Radiation Technologies, NAS of Ukraine, 61002 Kharkov (Ukraine); Kasilov, A.A.; Kolenov, I.V. [Institute of Plasma Physics, National Scientific Center “KIPT”, 61108 Kharkov (Ukraine); Konovalov, V.G. [National Technical University, “Kharkiv Polytechnical Institute”, 61002 Kharkov (Ukraine); Skoryk, O.O.; Solodovchenko, S.I. [Institute of Plasma Physics, National Scientific Center “KIPT”, 61108 Kharkov (Ukraine)

2013-03-15

The effect of heavy sputtering and of neutron irradiation simulated by displacement damaging with of 20 MeV W{sup 6+} ions on the optical properties of tungsten mirrors was studied. Ar{sup +} ions with 600 eV of energy were used as imitation of charge exchange atoms ejected from fusion plasma. The ion fluence dependence of the surface topography and the optical properties of polycrystalline, recrystallized tungsten (grain size 20–100 μm) were studied by optical microscopy, interferometry, reflectometry and ellipsometry. Furthermore, after sputtering in total a layer of 3.9 μm in thickness, the orientation and the thickness of the eroded layer of many individual grains was determined by electron backscattering diffraction and confocal laser scanning microscopy. Concluding from the obtained data the neutron irradiation, at least at the damage level would be achieved in ITER, has not to make an additional contribution in the processes developing under impact of charge exchange atoms only.

Effects of high-energy electro-pulsing treatment on microstructure, mechanical properties and corrosion behavior of Ti-6Al-4V alloy.

Science.gov (United States)

Ye, Xiaoxin; Wang, Lingsheng; Tse, Zion T H; Tang, Guoyi; Song, Guolin

2015-04-01

The effect of electro-pulsing treatment (EPT) on the microstructure, mechanical properties and corrosion behavior of cold-rolled Ti-6Al-4V alloy strips was investigated in this paper. It was found that the elongation to failure of materials obtains a noticeable enhancement with increased EPT processing time while slightly sacrificing strength. Fine recrystallized grains and the relative highest elongation to failure (32.5%) appear in the 11second-EPT samples. Grain coarsening and decreased ductility were brought in with longer EPT duration time. Fracture surface analysis shows that transition from intergranular brittle facture to transgranular dimple fracture takes place with an increase in processing time of EPT. Meanwhile, corrosion behavior of titanium alloys is greatly improved with increased EPT processing time, which is presented by polarization test and surface observation with the beneficial effect of forming a protective anatase-TiO2 film on the surface of alloys. The rapid recrystallization behavior and oxide formation of the titanium alloy strip under EPTs are attributed to the enhancement of nucleation rate, atomic diffusion and oxygen migration resulting from the coupling of the thermal and athermal effects. Copyright © 2015 Elsevier B.V. All rights reserved.

Symmetry Breaking in Space-Time Hierarchies Shapes Brain Dynamics and Behavior.

Science.gov (United States)

Pillai, Ajay S; Jirsa, Viktor K

2017-06-07

In order to maintain brain function, neural activity needs to be tightly coordinated within the brain network. How this coordination is achieved and related to behavior is largely unknown. It has been previously argued that the study of the link between brain and behavior is impossible without a guiding vision. Here we propose behavioral-level concepts and mechanisms embodied as structured flows on manifold (SFM) that provide a formal description of behavior as a low-dimensional process emerging from a network's dynamics dependent on the symmetry and invariance properties of the network connectivity. Specifically, we demonstrate that the symmetry breaking of network connectivity constitutes a timescale hierarchy resulting in the emergence of an attractive functional subspace. We show that behavior emerges when appropriate conditions imposed upon the couplings are satisfied, justifying the conductance-based nature of synaptic couplings. Our concepts propose design principles for networks predicting how behavior and task rules are represented in real neural circuits and open new avenues for the analyses of neural data. Copyright © 2017 Elsevier Inc. All rights reserved.

The Behavior of Procurement Process as Described by Using System Dynamics Methodology

OpenAIRE

Mohd Yusoff, Mohd Izhan

2018-01-01

System dynamics methodology has been used in many fields of study which include supply chain, project management and performance, and procurement process. The said methodology enables the researchers to identify and study the impact of the variables or factors on the outcome of the model they developed. In this paper, we showed the use of system dynamics methodology in studying the behavior of procurement process that is totally different from those mentioned in previous studies. By using a t...

Development of re-crystallized W-1.1%TiC with enhanced room-temperature ductility and radiation performance

International Nuclear Information System (INIS)

Kurishita, H.; Matsuo, S.; Arakawa, H.; Sakamoto, T.; Kobayashi, S.; Nakai, K.; Takida, T.; Kato, M.; Kawai, M.; Yoshida, N.

2010-01-01

Ultra-fine grained (UFG) W-TiC compacts fabricated by powder metallurgical methods utilizing mechanical alloying (MA) are very promising for use in irradiation environments. However, the assurance of room-temperature ductility and enhancement in surface resistances to low-energy hydrogen irradiation are unsettled issues. As an approach to solution to these, microstructural modification by hot plastic working has been applied to UFG W-TiC processed by MA in a purified Ar or H 2 atmosphere and hot isostatic pressing (HIP). Hot plastically worked compacts have been subjected to 3-point bend tests at room temperature and TEM microstructural examinations. It is found that the microstructural modification allows us to convert UFG W-1.1%TiC to compacts exhibiting a very high fracture strength and appreciable ductility at room temperature. The compacts of W-1.1%TiC/Ar (MA atmosphere: Ar) and W-1.1%TiC/H 2 (MA atmosphere: H 2 ) exhibit re-crystallized structures with approximately 0.5 and 1.5 μm in grain size, respectively. It is shown that the enhancement of fracture resistance by microstructural modifications is attributed to significant strengthening of weak grain boundaries in the re-crystallized state. As a result the modified compacts exhibit superior surface resistance to low-energy deuteron irradiation.

Dynamical behavior of a single polymer chain under nanometric confinement

Science.gov (United States)

Lagrené, K.; Zanotti, J.-M.; Daoud, M.; Farago, B.; Judeinstein, P.

2010-10-01

We address the dynamical behavior of a single polymer chain under nanometric confinement. We consider a polymer melt made of a mixture of hydrogenated and deuterated high molecular mass Poly(Ethylene Oxide) (PEO). The confining material is a membrane of Anodic Aluminum Oxide (AAO), a macroscopically highly ordered confining system made of parallel cylindrical channels. We use Neutron Spin-Echo (NSE) under the Zero Average Contrast (ZAC) condition to, all at once, i) match the intense porous AAO detrimental elastic SANS (Small Angle Neutron Scattering) contribution to the total intermediate scattering function I(Q,t) and ii) measure the Q dependence of the dynamical modes of a single chain under confinement. The polymer dynamics is probed on an extremely broad spacial ([2.2 10-2 Å-1, 0.2 Å-1]) and temporal ([0.1 ns, 600 ns]) ranges. We do not detect any influence of confinement on the polymer dynamics. This result is discussed in the framework of the debate on the existence of a "corset effect" recently suggested by NMR relaxometry data.

Managing lifelike behavior in a dynamic self-assembled system

Science.gov (United States)

Ropp, Chad; Bachelard, Nicolas; Wang, Yuan; Zhang, Xiang

Self-organization can arise outside of thermodynamic equilibrium in a process of dynamic self-assembly. This is observed in nature, for example in flocking birds, but can also be created artificially with non-living entities. Such dynamic systems often display lifelike properties, including the ability to self-heal and adapt to environmental changes, which arise due to the collective and often complex interactions between the many individual elements. Such interactions are inherently difficult to predict and control, and limit the development of artificial systems. Here, we report a fundamentally new method to manage dynamic self-assembly through the direct external control of collective phenomena. Our system consists of a waveguide filled with mobile scattering particles. These particles spontaneously self-organize when driven by a coherent field, self-heal when mechanically perturbed, and adapt to changes in the drive wavelength. This behavior is governed by particle interactions that are completely mediated by coherent wave scattering. Compared to hydrodynamic interactions which lead to compact ordered structures, our system displays sinusoidal degeneracy and many different steady-state geometries that can be adjusted using the external field.

Study on hot deformation behavior and microstructure evolution of cast-extruded AZ31B magnesium alloy and nanocomposite using processing map

International Nuclear Information System (INIS)

Srinivasan, M.; Loganathan, C.; Narayanasamy, R.; Senthilkumar, V.; Nguyen, Q.B.; Gupta, M.

2013-01-01

Highlights: ► Hot deformation behavior of AZ31B Mg alloy and nanocomposite were studied. ► Activation energy of AZ31B Mg alloy and nanocomposite were determined. ► Twining, shear bands and flow localization were observed. - Abstract: The hot deformation behavior and microstructural evolution of cast-extruded AZ31B magnesium alloy and nanocomposite have been studied using processing-maps. Compression tests were conducted in the temperature range of 250–400 °C and strain rate range of 0.01–1.0 s −1 . The three-dimensional (3D) processing maps developed in this work, describe the variations of the efficiency of power dissipation and flow instability domains in the strain rate (ε) and temperature (T) space. The deformation mechanisms namely dynamic recrystallization (DRX), dynamic recovery (DRY) and instability regions were identified using processing maps. The deformation mechanisms were also correlated with transmission electron microscopy (TEM) and optical microscopy (OM). The optimal region for hot working has been observed at a strain rate (ε) of 0.01 s −1 and the temperature (T) of 400 °C for both magnesium alloy and nanocomposite. Few instability regimes have been identified in this study at higher strain rate (ε) and temperature (T). The stability domains have been identified in the lower strain rate regimes

Study on Hot Deformation Behavior of 7085 Aluminum Alloy during Backward Extrusion Process

Directory of Open Access Journals (Sweden)

R. B. Mei

2015-01-01

Full Text Available Compression test was carried out and the true stress-strain curves were obtained from the hot compression of 7085 alloy. A numerical simulation on the deformation behavior of 7085 aluminum alloy during the backward extrusion was also performed by finite element method. The results show that dynamic recrystallization occurs in the hot compression of 7085 alloy and the peak stress reaches higher values as the strain rate increases and deformation temperature decreases. The backward extrusion processes include contact deformation, initial deformation, and steady deformation. Severe plastic deformation of shear and compression occurs when the metal flowed into the channel between fillet of punch and wall of die so that the grain size can be refined by backward extrusion. The deformation in the region of top of wall is too small to meet the mechanical properties of requirements and the metal usually needs to be trimmed. The experiments with the same parameters as simulation had been carried out and the experimental cup after extrusion has better quality.

Dynamic psychotherapy or dialectical behavioral therapy-- which is better for borderline personality disorder?

Science.gov (United States)

Tene, O; Har-Even, A; Dahan, E; Babokshin, Y; Reuveni, I; Ponarovsky, B; Rosman, V; Gluzman, L

2011-01-01

Clinical dilemma: A 20-year-old female patient, diagnosed as suffering from borderline personality disorder, is referred to your clinic. Her disorder is characterized by unstable personal relationships, impulsivity, suicidal behavior, emotional instability and pan-anxiety. After initiation of pharmacological treatment which you have chosen, you meet with her parents who ask you which is better for their daughter dynamic-analytic psychotherapy or dialectical behavioral therapy.

The effect of emotional responses on endogenous dynamics of activity-travel behavior: numerical simulation results

NARCIS (Netherlands)

Psarra, I.; Arentze, T.A.; Timmermans, H.J.P.

2014-01-01

The current study aims at developing a model of endogenous dynamics of activity-travel behavior. Endogenous dynamics are induced by stress, which is regarded as dissatisfaction with current habits. It is assumed that people try to alleviate stress by hierarchically trying short-term and then

Re-crystallization of ITO films after carbon irradiation

Energy Technology Data Exchange (ETDEWEB)

Usman, Muhammad, E-mail: usmanm@ncp.edu.pk [Experimental Physics Laboratories, National Centre for Physics, Shahdara Valley Road, Quaid-i-Azam University, Islamabad (Pakistan); Khan, Shahid, E-mail: shahidkhan@zju.edu.cn [State Key Laboratory of Silicon Materials, School of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Khan, Majid [Department of Physics, Quaid-i-Azam University, Islamabad (Pakistan); Abbas, Turab Ali [Experimental Physics Laboratories, National Centre for Physics, Shahdara Valley Road, Quaid-i-Azam University, Islamabad (Pakistan)

2017-01-15

Highlights: • Carbon irradiation on ITO destroys crystal structure until threshold ion fluence. • Carbon irradiation induced amorphization in ITO is recoverable at higher fluence. • Optical transmittance is reduced after carbon irradiation. • Electrical resistivity is increased after irradiation with carbon ions in ITO. • Bandgap is reduced with increasing fluence of carbon irradiation. - Abstract: 2.0 MeV carbon ion irradiation effects on Indium Tin Oxide (ITO) thin films on glass substrate are investigated. The films are irradiated with carbon ions in the fluence range of 1 × 10{sup 13} to 1 × 10{sup 15} ions/cm{sup 2}. The irradiation induced effects in ITO are compared before and after ion bombardment by systematic study of structural, optical and electrical properties of the films. The XRD results show polycrystalline nature of un-irradiated ITO films which turns to amorphous state after 1 × 10{sup 13} ions/cm{sup 2} fluence of carbon ions. Further increase in ion fluence to 1 × 10{sup 14} ions/cm{sup 2} re-crystallizes the structure and retains for even higher fluences. A gradual decrease in the electrical conductivity and transmittance of irradiated samples is observed with increasing ion fluence. The band gap of the films is observed to be decreased after carbon irradiation.

Re-crystallization of ITO films after carbon irradiation

International Nuclear Information System (INIS)

Usman, Muhammad; Khan, Shahid; Khan, Majid; Abbas, Turab Ali

2017-01-01

Highlights: • Carbon irradiation on ITO destroys crystal structure until threshold ion fluence. • Carbon irradiation induced amorphization in ITO is recoverable at higher fluence. • Optical transmittance is reduced after carbon irradiation. • Electrical resistivity is increased after irradiation with carbon ions in ITO. • Bandgap is reduced with increasing fluence of carbon irradiation. - Abstract: 2.0 MeV carbon ion irradiation effects on Indium Tin Oxide (ITO) thin films on glass substrate are investigated. The films are irradiated with carbon ions in the fluence range of 1 × 10"1"3 to 1 × 10"1"5 ions/cm"2. The irradiation induced effects in ITO are compared before and after ion bombardment by systematic study of structural, optical and electrical properties of the films. The XRD results show polycrystalline nature of un-irradiated ITO films which turns to amorphous state after 1 × 10"1"3 ions/cm"2 fluence of carbon ions. Further increase in ion fluence to 1 × 10"1"4 ions/cm"2 re-crystallizes the structure and retains for even higher fluences. A gradual decrease in the electrical conductivity and transmittance of irradiated samples is observed with increasing ion fluence. The band gap of the films is observed to be decreased after carbon irradiation.

Stocks’ pricing dynamics and behavioral finance: A review

Directory of Open Access Journals (Sweden)