WorldWideScience

Sample records for dynamic pressure

  1. Dynamic pressures in porous media

    Science.gov (United States)

    Balcerak, Ernie

    2012-12-01

    Understanding the relationship between fluid pressures and water content (saturation) in soils or other porous media can be important in a wide range of practical areas, including oil recovery, infiltration and flooding during extreme weather events, and environmental remediation. The relationship between fluid pressures and saturation in porous media has been reported to be dynamic—to depend on the flow rate as saturation changes. However, previous studies designed to understand the dynamic component of this relationship have been highly contradictory. To learn more, Hou et al. conducted experiments to quantify the relationship between pressure and rate of saturation change using a small-volume system with highly characterized fluid selective microsensors. Their analyses corrected for two often-overlooked experimental artifacts: gas pressure gradients and sensor response rate. When the researchers applied these corrections, they found that the dependence of pressure on the rate of saturation change may be much less significant than previously thought. (Water Resources Research, doi:10.1029/2012WR012434, 2012)

  2. Theoretical research on aggregative dynamic pressure damper

    Institute of Scientific and Technical Information of China (English)

    HU Jun-hua; CAO Shu-ping; LUO Xiao-hui; NIU Zi-hua; XIN Ji-song

    2009-01-01

    To broaden the frequency width and increase the damping coefficient of a dynamic pressure damper, we designed an aggregative dynamic pressure damper (ADPD). Combined with the advantages of traditional dynamic pressure dampers (TDPD), ADPD can not only increase the damping coefficient in wide frequency range for valve control system, but also absorb partial pressure pulsations and impacts in the low and high frequency fields. Based on the theoretical research and the analysis compared with TDPD, we concluded that the ADPD was superior to the TDPD in the middle high frequency field, and the main parameters influencing the performance of the damper were the damping stiffness, orifice flow coefficient, pre-charge pressure, and the volume of the damper accumulator.

  3. Dynamic active earth pressure on retaining structures

    Indian Academy of Sciences (India)

    Deepankar Choudhury; Santiram Chatterjee

    2006-12-01

    Earth-retaining structures constitute an important topic of research in civil engineering, more so under earthquake conditions. For the analysis and design of retaining walls in earthquake-prone zones, accurate estimation of dynamic earth pressures is very important. Conventional methods either use pseudo-static approaches of analysis even for dynamic cases or a simple single-degree of freedom model for the retaining wall–soil system. In this paper, a simplified two-degree of freedom mass–spring–dashpot (2-DOF) dynamic model has been proposed to estimate the active earth pressure at the back of the retaining walls for translation modes of wall movement under seismic conditions. The horizontal zone of influence on dynamic earth force on the wall is estimated. Results in terms of displacement, velocity and acceleration-time history are presented for some typical cases, which show the final movement of the wall in terms of wall height, which is required for the design. The non-dimensional design chart proposed in the present study can be used to compute the total dynamic earth force on the wall under different input ground motion and backfill conditions. Finally, the results obtained have been compared with those of the available Scott model and the merits of the present results have been discussed.

  4. High Temperature Dynamic Pressure Measurements Using Silicon Carbide Pressure Sensors

    Science.gov (United States)

    Okojie, Robert S.; Meredith, Roger D.; Chang, Clarence T.; Savrun, Ender

    2014-01-01

    Un-cooled, MEMS-based silicon carbide (SiC) static pressure sensors were used for the first time to measure pressure perturbations at temperatures as high as 600 C during laboratory characterization, and subsequently evaluated in a combustor rig operated under various engine conditions to extract the frequencies that are associated with thermoacoustic instabilities. One SiC sensor was placed directly in the flow stream of the combustor rig while a benchmark commercial water-cooled piezoceramic dynamic pressure transducer was co-located axially but kept some distance away from the hot flow stream. In the combustor rig test, the SiC sensor detected thermoacoustic instabilities across a range of engine operating conditions, amplitude magnitude as low as 0.5 psi at 585 C, in good agreement with the benchmark piezoceramic sensor. The SiC sensor experienced low signal to noise ratio at higher temperature, primarily due to the fact that it was a static sensor with low sensitivity.

  5. CFD modeling of the IRIS pressurizer dynamic

    Energy Technology Data Exchange (ETDEWEB)

    Sanz, Ronny R.; Montesinos, Maria E.; Garcia, Carlos; Bueno, Elizabeth D.; Mazaira, Leorlen R., E-mail: rsanz@instec.cu, E-mail: mmontesi@instec.cu, E-mail: cgh@instec.cu, E-mail: leored1984@gmail.com [Instituto Superior de Tecnologias y Ciencias Aplicadas (InSTEC), La Habana (Cuba); Bezerra, Jair L.; Lira, Carlos A.B. Oliveira, E-mail: jair.lima@ufpe.br, E-mail: cabol@ufpe.br [Universida Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Energia Nuclear

    2015-07-01

    Integral layout of nuclear reactor IRIS makes possible the elimination of the spray system, which is usually used to mitigate in-surge transient and also help to Boron homogenization. The study of transients with deficiencies in the Boron homogenization in this technology is very important, because they can cause disturbances in the reactor power and insert a strong reactivity in the core. The detailed knowledge of the behavior of multiphase multicomponent flows is challenging due to the complex phenomena and interactions at the interface. In this context, the CFD modeling is employed in the design of equipment in the nuclear industry as it allows predicting accidents or predicting their performance in dissimilar applications. The aim of the present research is to model the IRIS pressurizer's dynamic using the commercial CFD code CFX. A symmetric tri dimensional model equivalent to 1/8 of the total geometry was adopted to reduce mesh size and minimize processing time. The model considers the coexistence of four phases and also takes into account the heat losses. The relationships for interfacial mass, energy, and momentum transport are programmed and incorporated into CFX. Moreover, two subdomains and several additional variables are defined to monitoring the boron dilution sequences and condensation-evaporation rates in different control volumes. For transient states a non - equilibrium stratification in the pressurizer is considered. This paper discusses the model developed and the behavior of the system for representative transients sequences. The results of analyzed transients of IRIS can be applied to the design of pressurizer internal structures and components. (author)

  6. Magnetospheric Cavity Modes Driven by Solar Wind Dynamic Pressure Fluctuations

    CERN Document Server

    Claudepierre, S G; Elkington, S R; Lotko, W; Hudson, M K; 10.1029/2009GL039045

    2010-01-01

    We present results from Lyon-Fedder-Mobarry (LFM) global, three-dimensional magnetohydrodynamic (MHD) simulations of the solar wind-magnetosphere interaction. We use these simulations to investigate the role that solar wind dynamic pressure fluctuations play in the generation of magnetospheric ultra-low frequency (ULF) pulsations. The simulations presented in this study are driven with idealized solar wind input conditions. In four of the simulations, we introduce monochromatic ULF fluctuations in the upstream solar wind dynamic pressure. In the fifth simulation, we introduce a continuum of ULF frequencies in the upstream solar wind dynamic pressure fluctuations. In this numerical experiment, the idealized nature of the solar wind driving conditions allows us to study the magnetospheric response to only a fluctuating upstream dynamic pressure, while holding all other solar wind driving parameters constant. The simulation results suggest that ULF fluctuations in the solar wind dynamic pressure can drive magnet...

  7. Dynamic High-Pressure Behavior of Hierarchical Heterogeneous Geological Materials

    Science.gov (United States)

    2016-04-01

    pressure -density Hugoniot plots for simulations using the ‘mix 5’ option, as will be presented later. The volume weighted option for mixed cells (refered...AFRL-AFOSR-VA-TR-2016-0150 Dynamic High- Pressure Behavior of Geological Materials Naresh Thadhani GEORGIA TECH RESEARCH CORPORATION Final Report 04...31-12-2015 4.  TITLE AND SUBTITLE Dynamic High- Pressure Behavior of Hierarchical Heterogeneous Geological Materials 5a.  CONTRACT NUMBER 5b.  GRANT

  8. Oxygen Escape from Venus During High Dynamic Pressure ICMEs

    Science.gov (United States)

    McEnulty, Tess; Luhmann, J. G.; Brain, D. A.; Fedorov, A.; Jian, L. K.; Russell, C. T.; Zhang, T.; Möstl, C.; Futaana, Y.; de Pater, I.

    2013-10-01

    Previous studies using data from Pioneer Venus suggested that oxygen ion escape flux may be enhanced by orders of magnitude during Interplanetary Coronal Mass Ejections. However, this large enhancement has been ambiguous in Venus Express ion data - with some analyses showing no flux enhancement or a small enhancement (within 2 times undisturbed cases). One possible explanation is that high escape flux may be due to high dynamic pressure in the solar wind, and the dynamic pressure has been lower during the VEX time period. So, we focus on ICMEs with the largest dynamic pressure and with VEX sampling of the escaping ions during the sheath of the ICMEs (during which the highest dynamic pressures in the solar wind occur). We will show the characteristics of these large events measured by VEX, and compare them to the largest ICMEs measured by PVO. We will then discuss estimates of the oxygen ion escape flux during these events.

  9. Dynamic surface pressure measurements on a square cylinder with pressure sensitive paint

    Energy Technology Data Exchange (ETDEWEB)

    McGraw, C.M.; Khalil, G.; Callis, J.B. [University of Washington, Department of Chemistry, Seattle, WA (United States); Bell, J.H. [Ames Research Center, National Aeronautics and Space Administration, Moffett Field, CA (United States)

    2006-02-01

    The dynamic and static surface pressure on a square cylinder during vortex shedding was measured with pressure sensitive paints (PSPs) at three angles of incidence and a Reynolds number of 8.9 x 10{sup 4}. Oscillations in the phosphorescence intensity of the PSP that occurred at the vortex shedding frequency were observed. From these phosphorescent oscillations, the time-dependent changes in pressure distribution were calculated. This work extends PSP's useful range to dynamic systems where oscillating pressure changes are on the order of 230 Pa and occur at frequencies in the range of 95-125 Hz. (orig.)

  10. Noncontact Monitoring of Respiration by Dynamic Air-Pressure Sensor.

    Science.gov (United States)

    Takarada, Tohru; Asada, Tetsunosuke; Sumi, Yoshihisa; Higuchi, Yoshinori

    2015-01-01

    We have previously reported that a dynamic air-pressure sensor system allows respiratory status to be visually monitored for patients in minimally clothed condition. The dynamic air-pressure sensor measures vital information using changes in air pressure. To utilize this device in the field, we must clarify the influence of clothing conditions on measurement. The present study evaluated use of the dynamic air-pressure sensor system as a respiratory monitor that can reliably detect change in breathing patterns irrespective of clothing. Twelve healthy volunteers reclined on a dental chair positioned horizontally with the sensor pad for measuring air-pressure signals corresponding to respiration placed on the seat back of the dental chair in the central lumbar region. Respiratory measurements were taken under 2 conditions: (a) thinly clothed (subject lying directly on the sensor pad); and (b) thickly clothed (subject lying on the sensor pad covered with a pressure-reducing sheet). Air-pressure signals were recorded and time integration values for air pressure during each expiration were calculated. This information was compared with expiratory tidal volume measured simultaneously by a respirometer connected to the subject via face mask. The dynamic air-pressure sensor was able to receive the signal corresponding to respiration regardless of clothing conditions. A strong correlation was identified between expiratory tidal volume and time integration values for air pressure during each expiration for all subjects under both clothing conditions (0.840-0.988 for the thinly clothed condition and 0.867-0.992 for the thickly clothed condition). These results show that the dynamic air-pressure sensor is useful for monitoring respiratory physiology irrespective of clothing.

  11. Polyunsaturation in lipid membranes: dynamic properties and lateral pressure profiles.

    Science.gov (United States)

    Ollila, Samuli; Hyvönen, Marja T; Vattulainen, Ilpo

    2007-03-29

    We elucidate the influence of unsaturation on single-component membrane properties, focusing on their dynamical aspects and lateral pressure profiles across the membrane. To this end, we employ atomistic molecular dynamics simulations to study five different membrane systems with varying degrees of unsaturation, starting from saturated membranes and systematically increasing the level of unsaturation, ending up with a bilayer of phospholipids containing the docosahexaenoic acid. For an increasing level of unsaturation, we find considerable effects on dynamical properties, such as accelerated dynamics of the phosphocholine head groups and glycerol backbones and speeded up rotational dynamics of the lipid molecules. The lateral pressure profile is found to be altered by the degree of unsaturation. For an increasing number of double bonds, the peak in the middle of the bilayer decreases. This is compensated for by changes in the membrane-water interface region in terms of increasing peak heights of the lateral pressure profile. Implications of the findings are briefly discussed.

  12. Dynamic interface pressure distributions of two transtibial prosthetic socket concepts.

    Science.gov (United States)

    Dumbleton, Tim; Buis, Arjan W P; McFadyen, Angus; McHugh, Brendan F; McKay, Geoff; Murray, Kevin D; Sexton, Sandra

    2009-01-01

    In this study, we investigated and compared the dynamic interface pressure distribution of hands-off and hands-on transtibial prosthetic systems by means of pressure mapping. Of the 48 established unilateral amputees recruited, half (n = 24) had been wearing pressure-cast prostheses (IceCast Compact) and the other half (n = 24) had been wearing hand-cast sockets of the patellar tendon bearing design. We measured the dynamic pressure profile of more than 90% of the area within each prosthetic socket by means of four Tekscan F-Scan socket transducer arrays. We compared the interface pressure between socket concepts. We found that the distribution of dynamic pressure at the limb-socket interface was similar for the two intervention (socket prescription) groups. However, a significant difference was found in the magnitude of the interface pressure between the two socket concepts; the interface pressures recorded in the hands-off sockets were higher than those seen in the hands-on concept. Despite the differences in interface pressure, the level of satisfaction with the sockets was similar between subject groups. The sockets instrumented for this study had been in daily use for at least 6 months, with no residual-limb health problems.

  13. Dynamics of inner ear pressure change caused by intracranial pressure manipulation in the guinea pig

    NARCIS (Netherlands)

    Thalen, EO; Wit, HP; Segenhout, JM; Albers, FWJ

    2001-01-01

    Previous studies have shown that pressure changes in the cerebrospinal fluid compartment are transmitted to the inner ear. The main route for pressure transfer is the cochlear aqueduct, about which little is known with regard to its dynamic properties. In the present study, sudden intracranial press

  14. Dynamics of inner ear pressure change caused by intracranial pressure manipulation in the guinea pig

    NARCIS (Netherlands)

    Thalen, EO; Wit, HP; Segenhout, JM; Albers, FWJ

    Previous studies have shown that pressure changes in the cerebrospinal fluid compartment are transmitted to the inner ear. The main route for pressure transfer is the cochlear aqueduct, about which little is known with regard to its dynamic properties. In the present study, sudden intracranial

  15. Osmosis-based pressure generation: dynamics and application.

    Science.gov (United States)

    Bruhn, Brandon R; Schroeder, Thomas B H; Li, Suyi; Billeh, Yazan N; Wang, K W; Mayer, Michael

    2014-01-01

    This paper describes osmotically-driven pressure generation in a membrane-bound compartment while taking into account volume expansion, solute dilution, surface area to volume ratio, membrane hydraulic permeability, and changes in osmotic gradient, bulk modulus, and degree of membrane fouling. The emphasis lies on the dynamics of pressure generation; these dynamics have not previously been described in detail. Experimental results are compared to and supported by numerical simulations, which we make accessible as an open source tool. This approach reveals unintuitive results about the quantitative dependence of the speed of pressure generation on the relevant and interdependent parameters that will be encountered in most osmotically-driven pressure generators. For instance, restricting the volume expansion of a compartment allows it to generate its first 5 kPa of pressure seven times faster than without a restraint. In addition, this dynamics study shows that plants are near-ideal osmotic pressure generators, as they are composed of many small compartments with large surface area to volume ratios and strong cell wall reinforcements. Finally, we demonstrate two applications of an osmosis-based pressure generator: actuation of a soft robot and continuous volume delivery over long periods of time. Both applications do not need an external power source but rather take advantage of the energy released upon watering the pressure generators.

  16. Osmosis-based pressure generation: dynamics and application.

    Directory of Open Access Journals (Sweden)

    Brandon R Bruhn

    Full Text Available This paper describes osmotically-driven pressure generation in a membrane-bound compartment while taking into account volume expansion, solute dilution, surface area to volume ratio, membrane hydraulic permeability, and changes in osmotic gradient, bulk modulus, and degree of membrane fouling. The emphasis lies on the dynamics of pressure generation; these dynamics have not previously been described in detail. Experimental results are compared to and supported by numerical simulations, which we make accessible as an open source tool. This approach reveals unintuitive results about the quantitative dependence of the speed of pressure generation on the relevant and interdependent parameters that will be encountered in most osmotically-driven pressure generators. For instance, restricting the volume expansion of a compartment allows it to generate its first 5 kPa of pressure seven times faster than without a restraint. In addition, this dynamics study shows that plants are near-ideal osmotic pressure generators, as they are composed of many small compartments with large surface area to volume ratios and strong cell wall reinforcements. Finally, we demonstrate two applications of an osmosis-based pressure generator: actuation of a soft robot and continuous volume delivery over long periods of time. Both applications do not need an external power source but rather take advantage of the energy released upon watering the pressure generators.

  17. Prediction of Dynamic Wellbore Pressure in Gasified Fluid Drilling

    Institute of Scientific and Technical Information of China (English)

    Wang Zhiming; Ping Liqiu; Zou Ke

    2007-01-01

    The basis of designing gasified drilling is to understand the behavior of gas/liquid two-phase flow in the wellbore. The equations of mass and momentum conservation and equation of fluid flow in porous media were used to establish a dynamic model to predict weIlbore pressure according to the study results of Ansari and Beggs-Brill on gas-liquid two-phase flow. The dynamic model was solved by the finite difference approach combined with the mechanistic steady state model. The mechanistic dynamic model was numerically implemented into a FORTRAN 90 computer program and could simulate the coupled flow of fluid in wellbore and reservoir. The dynamic model revealed the effects of wellhead back pressure and injection rate of gas/liquid on bottomhole pressure. The model was validated against full-scale experimental data, and its 5.0% of average relative error could satisfy the accuracy requirements in engineering design.

  18. Pressure Dynamic Characteristics of Pressure Controlled Ventilation System of a Lung Simulator

    Directory of Open Access Journals (Sweden)

    Yan Shi

    2014-01-01

    Full Text Available Mechanical ventilation is an important life support treatment of critically ill patients, and air pressure dynamics of human lung affect ventilation treatment effects. In this paper, in order to obtain the influences of seven key parameters of mechanical ventilation system on the pressure dynamics of human lung, firstly, mechanical ventilation system was considered as a pure pneumatic system, and then its mathematical model was set up. Furthermore, to verify the mathematical model, a prototype mechanical ventilation system of a lung simulator was proposed for experimental study. Last, simulation and experimental studies on the air flow dynamic of the mechanical ventilation system were done, and then the pressure dynamic characteristics of the mechanical system were obtained. The study can be referred to in the pulmonary diagnostics, treatment, and design of various medical devices or diagnostic systems.

  19. Dynamic tire pressure sensor for measuring ground vibration.

    Science.gov (United States)

    Wang, Qi; McDaniel, James Gregory; Wang, Ming L

    2012-11-07

    This work presents a convenient and non-contact acoustic sensing approach for measuring ground vibration. This approach, which uses an instantaneous dynamic tire pressure sensor (DTPS), possesses the capability to replace the accelerometer or directional microphone currently being used for inspecting pavement conditions. By measuring dynamic pressure changes inside the tire, ground vibration can be amplified and isolated from environmental noise. In this work, verifications of the DTPS concept of sensing inside the tire have been carried out. In addition, comparisons between a DTPS, ground-mounted accelerometer, and directional microphone are made. A data analysis algorithm has been developed and optimized to reconstruct ground acceleration from DTPS data. Numerical and experimental studies of this DTPS reveal a strong potential for measuring ground vibration caused by a moving vehicle. A calibration of transfer function between dynamic tire pressure change and ground acceleration may be needed for different tire system or for more accurate application.

  20. Optic Fiber-Based Dynamic Pressure Sensor

    Institute of Scientific and Technical Information of China (English)

    Jiu-Lin Gan; Hai-Wen Cai; Jian-Xin Geng; Zheng-Qing Pan; Rong-Hui Qu; Zu-Jie Fang

    2008-01-01

    Weigh-in-Motion(WIM) technique is the process of measuring the dynamic tire forces of a moving vehicle and estimating the corresponding tire loads of the static vehicle. Compared with the static weigh station, WIM station is an efficient and cost effective choice that will minimize unneccessary stops and delay for truckers. The way to turn birefringence of single-mode fiber into a prime quality for a powerful and reliable sensor is shown. Preliminary results for the development of a weigh-in-motion (WIM) technique based on sagnac-loop sensor are presented. After a brief description of the sensor and its principle of operation, the theoretical model is developed. Then, a full characterization made in static conditions is presented.

  1. Finger and Palm Dynamic Pressure Monitoring for Basketball Shooting

    Directory of Open Access Journals (Sweden)

    Chiao-Fang Hung

    2017-01-01

    Full Text Available This study verified general inferences on the finger and palm pressure distribution of a basketball player in the moment before that player shoots a basketball through a scientific qualitative testing method. We mounted the sensor on the hands of college basketball players and monitored the dynamic pressure of each player’s hand while the player threw a basketball. The dynamic pressure distribution of the fingers and palm of a basketball player throwing a ball can be verified. According to the experimental results, college basketball players typically use the index finger to control the direction and power of force in the moment before shooting a basketball. This study successfully used a scientific qualitative test method to monitor the dynamic pressure of the fingers and palms of basketball players and verified the general inference that a typical basketball player mainly uses the index finger to control the direction and power of force in the moment before throwing a ball. In the future, this study, measuring the dynamic pressure distribution of the fingers and palm, can be applied to simulate hand manipulation in many biomedical and robotic applications.

  2. Modeling the pressure inactivation dynamics of Escherichia coli

    Directory of Open Access Journals (Sweden)

    Yamamoto K.

    2005-01-01

    Full Text Available Escherichia coli, as a model microorganism, was treated in phosphate-buffered saline under high hydrostatic pressure between 100 and 300 MPa, and the inactivation dynamics was investigated from the viewpoint of predictive microbiology. Inactivation data were curve fitted by typical predictive models: logistic, Gompertz and Weibull functions. Weibull function described the inactivation curve the best. Two parameters of Weibull function were calculated for each holding pressure and their dependence on holding pressure was obtained by interpolation. With the interpolated parameters, inactivation curves were simulated and compared with the experimental data sets.

  3. A Direct Two-Dimensional Pressure Formulation in Molecular Dynamics

    CERN Document Server

    YD, Sumith

    2016-01-01

    Two-dimensional (2D) pressure field estimation in molecular dynamics (MD) simulations has been done using three-dimensional (3D) pressure field calculations followed by averaging, which is computationally expensive due to 3D convolutions. In this work, we develop a direct 2D pressure field estimation method which is much faster than 3D methods without losing accuracy. The method is validated with MD simulations on two systems: a liquid film and a cylindrical drop of argon suspended in surrounding vapor.

  4. Molecular dynamics study of helium bubble pressure in titanium

    Institute of Scientific and Technical Information of China (English)

    Zhang Bao-Ling; Wang Jun; Hou Qing

    2011-01-01

    In this paper, the pressure state of the helium bubble in titanium is simulated by a molecular dynamics (MD) method. First, the possible helium/vacancy ratio is determined according to therelation between the bubble pressure and helium/vacancy ratio; then the dependences of the helium bubble pressure on the bubble radius at different temperatures are studied. It is shown that the product of the bubble pressure and the radius is approximately a constant, a result justifying the pressure-radius relation predicted by thermodynamics-based theory for gas bubble. Furthermore, a state equation of the helium bubble is established based on the MD calculations. Comparison between the results obtained by the state equation and corresponding experimental data shows that the state equation can describe reasonably the state of helium bubble and thus could be used for Monte Carlo simulations of the evolution of helium bubble in metals.

  5. Irrigation dynamic pressure-assisted hydrodissection during cataract surgery

    Directory of Open Access Journals (Sweden)

    Masuda Y

    2017-02-01

    Full Text Available Yoichiro Masuda,1 Hisaharu Iwaki,2 Noriko Kato,1 Genichiro Takahashi,1 Kotaro Oki,3 Hiroshi Tsuneoka4 1Department of Ophthalmology, The Jikei University, Katsushika Medical Center, 2Iwaki Eye Clinic, 3Oki Eye Surgery Center, 4Department of Ophthalmology, The Jikei University, School of Medicine, Tokyo, Japan Abstract: The irrigation dynamic pressure-assisted hydrodissection technique (irrigation-hydro [iH] does not require performing manual hydrodissection using a syringe and cannula to achieve cortical-capsular cleavage during cataract surgery. Since the iH technique uses the phaco tip to intentionally vacuum the intraocular fluid in order to induce the irrigation dynamic pressure for cortical-capsular cleavage, there is a reduction in the intraocular pressure (IOP from the bottle-height-dependent hydrostatic pressure. Thus, since the peak irrigation pressure derived from the phaco tip sleeve will be limited by the height of the irrigation fluid bottle, this is advantageous in helping to avoid excessively high IOP during cortical-capsular hydrodissection. Using this technique, we were able to effectively perform phacoemulsification without complications in 607 of 609 cataract eyes. Our findings show that utilization of the iH technique would be of benefit to patients, as it prevents high-pressure hydrodissection-related complications, such as capsular block syndrome and tears in the anterior hyaloid membrane during cataract surgery. Keywords: cataract surgery, hydrodissection, irrigation pressure, hydrodissection-related complication, capsular block syndrome, anterior hyaloid membrane tear, FLACS

  6. Water dynamics and retrogradation of ultrahigh pressurized wheat starch.

    Science.gov (United States)

    Doona, Christopher J; Feeherry, Florence E; Baik, Moo-Yeol

    2006-09-06

    The water dynamics and retrogradation kinetics behavior of gelatinized wheat starch by either ultrahigh pressure (UHP) processing or heat are investigated. Wheat starch completely gelatinized in the condition of 90, 000 psi at 25 degrees C for 30 min (pressurized gel) or 100 degrees C for 30 min (heated gel). The physical properties of the wheat starches were characterized in terms of proton relaxation times (T2 times) measured using time-domain nuclear magnetic resonance spectroscopy and evaluated using commercially available continuous distribution modeling software. Different T2 distributions in both micro- and millisecond ranges between pressurized and heated wheat starch gels suggest distinctively different water dynamics between pressurized and heated wheat starch gels. Smaller water self-diffusion coefficients were observed for pressurized wheat starch gels and are indicative of more restricted translational proton mobility than is observed with heated wheat starch gels. The physical characteristics associated with changes taking place during retrogradation were evaluated using melting curves obtained with differential scanning calorimetry. Less retrogradation was observed in pressurized wheat starch, and it may be related to a smaller quantity of freezable water in pressurized wheat starch. Starches comprise a major constituent of many foods proposed for commercial potential using UHP, and the present results furnish insight into the effect of UHP on starch gelatinization and the mechanism of retrogradation during storage.

  7. Two methods for absolute calibration of dynamic pressure transducers

    Science.gov (United States)

    Swift, G. W.; Migliori, A.; Garrett, S. L.; Wheatley, J. C.

    1982-12-01

    Two techniques are described for absolute calibration of a dynamic pressure transducer from 0 to 400 Hz in 1-MPa helium gas. One technique is based on a comparison to a mercury manometer; the other is based on the principle of reciprocity. The two techniques agree within the instrumental uncertainties of 1%.

  8. Dynamic Mode Decomposition of Fast Pressure Sensitive Paint Data

    Directory of Open Access Journals (Sweden)

    Mohd Y. Ali

    2016-06-01

    Full Text Available Fast-response pressure sensitive paint (PSP is used in this work to measure and analyze the acoustic pressure field in a rectangular cavity. The high spatial resolution and fast frequency response of PSP effectively captures the spatial and temporal detail of surface pressure resulting in the acoustic pressure field. In this work, a high-speed camera is used to generate a continuous time record of the acoustic pressure fluctuations with PSP. Since the level of the acoustic pressure is near the resolution limit of the sensor system, advanced analysis techniques are used to extract the spatial modes of the pressure field. Both dynamic mode decomposition (DMD and proper orthogonal decomposition (POD are compared with phase averaging for data analysis. While all three techniques effectively extract the pressure field and reduce the impact of sensor noise, DMD and POD are more robust techniques that can be applied to aperiodic or multi-frequency signals. Furthermore, DMD is better than POD at suppressing noise in particular regions of the spectrum and at effectively separating spectral energy when multiple acoustic excitation frequencies are present.

  9. Richtmyer-Meshkov unstable dynamics influenced by pressure fluctuations

    Science.gov (United States)

    Bhowmick, A. K.; Abarzhi, S. I.

    2016-11-01

    We theoretically study the effect of pressure fluctuations on the Richtmyer-Meshkov (RM) unstable interface in approximation of ideal incompressible immiscible fluids and two-dimensional flow. Pressure fluctuations are treated as an effective acceleration directed from the heavy to light fluid with inverse square time dependence. The group theory approach is applied to analyze large-scale coherent dynamics, solve the complete set of the governing equations, and find regular asymptotic solutions describing RM bubbles. A strong effect is found, for the first time to our knowledge, of pressure fluctuations on the interface morphology and dynamics. In the linear regime, a nearly flat bubble gets more curved, and its velocity increases for strong pressure fluctuations and decreases otherwise. In the nonlinear regime, solutions form a one-parameter family parameterized by the bubble front curvature. For the fastest stable solution in the family, the RM bubble is curved for strong pressure fluctuations and is flattened otherwise. The flow is characterized by the intense motion of the fluids in the vicinity of the interface, effectively no motion away from the interface, and presence of shear at the interface leading to formation of smaller scale vortical structures. Our theoretical results agree with and explain existing experiments and simulations and identify new qualitative and quantitative characteristics to evaluate the strength of pressure fluctuations in experiments and simulations.

  10. Tyre pressure monitoring using a dynamical model-based estimator

    Science.gov (United States)

    Reina, Giulio; Gentile, Angelo; Messina, Arcangelo

    2015-04-01

    In the last few years, various control systems have been investigated in the automotive field with the aim of increasing the level of safety and stability, avoid roll-over, and customise handling characteristics. One critical issue connected with their integration is the lack of state and parameter information. As an example, vehicle handling depends to a large extent on tyre inflation pressure. When inflation pressure drops, handling and comfort performance generally deteriorate. In addition, it results in an increase in fuel consumption and in a decrease in lifetime. Therefore, it is important to keep tyres within the normal inflation pressure range. This paper introduces a model-based approach to estimate online tyre inflation pressure. First, basic vertical dynamic modelling of the vehicle is discussed. Then, a parameter estimation framework for dynamic analysis is presented. Several important vehicle parameters including tyre inflation pressure can be estimated using the estimated states. This method aims to work during normal driving using information from standard sensors only. On the one hand, the driver is informed about the inflation pressure and he is warned for sudden changes. On the other hand, accurate estimation of the vehicle states is available as possible input to onboard control systems.

  11. Computational Fluid Dynamics Analysis of High Injection Pressure Blended Biodiesel

    Science.gov (United States)

    Khalid, Amir; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari

    2017-08-01

    Biodiesel have great potential for substitution with petrol fuel for the purpose of achieving clean energy production and emission reduction. Among the methods that can control the combustion properties, controlling of the fuel injection conditions is one of the successful methods. The purpose of this study is to investigate the effect of high injection pressure of biodiesel blends on spray characteristics using Computational Fluid Dynamics (CFD). Injection pressure was observed at 220 MPa, 250 MPa and 280 MPa. The ambient temperature was kept held at 1050 K and ambient pressure 8 MPa in order to simulate the effect of boost pressure or turbo charger during combustion process. Computational Fluid Dynamics were used to investigate the spray characteristics of biodiesel blends such as spray penetration length, spray angle and mixture formation of fuel-air mixing. The results shows that increases of injection pressure, wider spray angle is produced by biodiesel blends and diesel fuel. The injection pressure strongly affects the mixture formation, characteristics of fuel spray, longer spray penetration length thus promotes the fuel and air mixing.

  12. Irrigation dynamic pressure-assisted hydrodissection during cataract surgery.

    Science.gov (United States)

    Masuda, Yoichiro; Iwaki, Hisaharu; Kato, Noriko; Takahashi, Genichiro; Oki, Kotaro; Tsuneoka, Hiroshi

    2017-01-01

    The irrigation dynamic pressure-assisted hydrodissection technique (irrigation-hydro [iH]) does not require performing manual hydrodissection using a syringe and cannula to achieve cortical-capsular cleavage during cataract surgery. Since the iH technique uses the phaco tip to intentionally vacuum the intraocular fluid in order to induce the irrigation dynamic pressure for cortical-capsular cleavage, there is a reduction in the intraocular pressure (IOP) from the bottle-height-dependent hydrostatic pressure. Thus, since the peak irrigation pressure derived from the phaco tip sleeve will be limited by the height of the irrigation fluid bottle, this is advantageous in helping to avoid excessively high IOP during cortical-capsular hydrodissection. Using this technique, we were able to effectively perform phacoemulsification without complications in 607 of 609 cataract eyes. Our findings show that utilization of the iH technique would be of benefit to patients, as it prevents high-pressure hydrodissection-related complications, such as capsular block syndrome and tears in the anterior hyaloid membrane during cataract surgery.

  13. Irrigation dynamic pressure-assisted hydrodissection during cataract surgery

    Science.gov (United States)

    Masuda, Yoichiro; Iwaki, Hisaharu; Kato, Noriko; Takahashi, Genichiro; Oki, Kotaro; Tsuneoka, Hiroshi

    2017-01-01

    The irrigation dynamic pressure-assisted hydrodissection technique (irrigation-hydro [iH]) does not require performing manual hydrodissection using a syringe and cannula to achieve cortical-capsular cleavage during cataract surgery. Since the iH technique uses the phaco tip to intentionally vacuum the intraocular fluid in order to induce the irrigation dynamic pressure for cortical-capsular cleavage, there is a reduction in the intraocular pressure (IOP) from the bottle-height-dependent hydrostatic pressure. Thus, since the peak irrigation pressure derived from the phaco tip sleeve will be limited by the height of the irrigation fluid bottle, this is advantageous in helping to avoid excessively high IOP during cortical-capsular hydrodissection. Using this technique, we were able to effectively perform phacoemulsification without complications in 607 of 609 cataract eyes. Our findings show that utilization of the iH technique would be of benefit to patients, as it prevents high-pressure hydrodissection-related complications, such as capsular block syndrome and tears in the anterior hyaloid membrane during cataract surgery. PMID:28243054

  14. Dynamic material strength measurement utilizing magnetically applied pressure-shear

    Directory of Open Access Journals (Sweden)

    Alexander C.S.

    2012-08-01

    Full Text Available Magnetically applied pressure-shear (MAPS is a recently developed technique used to measure dynamic material strength developed at Sandia National Laboratories utilizing magneto-hydrodynamic (MHD drive pulsed power systems. MHD drive platforms generate high pressures by passing a large current through a pair of parallel plate conductors which, in essence, form a single turn magnet coil. Lorentz forces resulting from the interaction of the self-generated magnetic field and the drive current repel the plates and result in a high pressure ramp wave propagating in the conductors. This is the principle by which the Sandia Z Machine operates for dynamic material testing. MAPS relies on the addition of a second, external magnetic field applied orthogonally to both the drive current and the self-generated magnetic field. The interaction of the drive current and this external field results in a shear wave being induced directly in the conductors. Thus both longitudinal and shear stresses are generated. These stresses are coupled to a sample material of interest where shear strength is probed by determining the maximum transmissible shear stress in the state defined by the longitudinal compression. Both longitudinal and transverse velocities are measured via a specialized velocity interferometer system for any reflector (VISAR. Pressure and shear strength of the sample are calculated directly from the VISAR data. Results of tests on several materials at modest pressures (∼10GPa will be presented and discussed.

  15. Dynamic damper pressure fluctuation in the pumping systems

    Directory of Open Access Journals (Sweden)

    O.V. Korolyov

    2016-05-01

    Full Text Available Inertial part of any devices and equipment (e.g., pumps, hung or mounted on the resilient frame and being under the influence of the disturbing force that works at a constant frequency, may be subject to fluctuations, especially near of the resonance area. For elimination these fluctuations, you can resort to the use of a dynamic damper. Aim: The aim of the work is an analytical study of various dynamic dampers to reduce pressure fluctuation problems in pumping systems. Materials and Methods: A comparative analysis of efficiency of functioning was carried out for two types of dynamic dampers - hydraulic and mechanical. Results: The technique for calculating of dynamic damper of fluid pressure fluctuations in the hydraulic and mechanical pumps is presented. Algorithms of calculations are reported to engineering applications and implemented in the production process. The calculations show that the use of dynamic mechanical dampers is expedient at high frequency pumps, and, with increasing frequency of the pump by 6 times, winning in the dimensions of the damper in 3.5 times.

  16. DYNAMICAL BEHAVIOR OF VISCOELASTIC CYLINDRICAL SHELLS UNDER AXIAL PRESSURES

    Institute of Scientific and Technical Information of China (English)

    程昌钧; 张能辉

    2001-01-01

    The hypotheses of the Kármán-Donnell theory of thin shells with large deflections and the Boltzmann laws for isotropic linear, viscoelastic materials, the constitutive equations of shallow shells are first derived. Then the governing equations for the deflection equations of elastic thin plates. Introducing proper assumptions, an approximate theory for viscoelastic cylindrical shells under axial pressures can be obtained. Finally, the dynamical behavior is studied in detail by using several numerical methods. Dynamical properties,such as, hyperchaos , chaos, strange attractor, limit cycle etc., are discovered.

  17. Pressure effects on dynamics behavior of multiwall boron nitride nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Talebian, Taha [Faculty of Engineering, Neyshabur Branch, Islamic Azad University, Neyshabur (Iran, Islamic Republic of)

    2016-01-15

    The dynamic behavior of Multiwall boron nitride nanotubes (MWBNNTs) is investigated by employing multiple elastic shells model. The influences of van der Waals interactions on layers are shown as nonlinear functions of the interlayer distance of MWBNNTs. Governing equations are solved by using the developed finite element method and by employing time history diagrams. The radial wave speed from the outermost layer to the innermost layer is computed. The effects of geometrical factors such as diameter-to-thickness ratio on dynamic behavior of MWBNNTs are determined. The magnification aspects of MWBNNTs are computed, and the effects of surrounding pressures on wave speed and magnification aspect of MWBNNTs are discussed.

  18. Material deformation dynamics at ultrahigh pressures and strain rates

    Science.gov (United States)

    Remington, B. A.; Park, H. S.; Maddox, B. R.; May, M. J.; Pollaine, S. M.; Prisbrey, S. T.; Rudd, R. E.; Hawreliak, J. A.; Perry, T. S.; Comley, A. J.; Wark, J. S.; Meyers, M. A.

    2010-11-01

    Solid-state dynamics experiments at extreme pressures, up to 10 Mbar, and strain rates (1.e6 -1.e8 1/s) are being developed for the NIF laser. The experimental methods are being developed on the Omega laser facility. VISAR measurements establish the ramped, high-pressure conditions. Recovery experiments offer a look at the residual microstructure. Dynamic diffraction measurements allow phase, shear stress (strength), and possibly twin volume fraction and dislocation density to be inferred. Constitutive models for material strength at these conditions by comparing 2D simulations with experiments measuring the Rayleigh-Taylor instability evolution in solid-state samples of vanadium and tantalum. The material deformation likely falls into the phonon drag regime. We estimate of the (microscopic) phonon drag coefficient, by relating to the (macroscopic) effective lattice viscosity.

  19. PPOOLEX experiments on dynamic loading with pressure feedback

    Energy Technology Data Exchange (ETDEWEB)

    Puustinen, M.; Laine, J.; Raesaenen, A. (Lappeenranta Univ. of Technology, Nuclear Safety Research Unit (Finland))

    2011-01-15

    This report summarizes the results of the dynamic loading experiments (DYN series) carried out with the scaled down, two compartment PPOOLEX test facility designed and constructed at LUT. Steam was blown into the dry well compartment and from there through the DN200 vertical blowdown pipe to the condensation pool filled with sub-cooled water. The main purpose of the experiments was to study dynamic loads caused by different condensation modes. Particularly, the effect of counterpressure on loads due to pressure oscillations induced by chugging was of interest. Before the experiments the condensation pool was filled with isothermal water so that the blowdown pipe outlet was submerged by 1.03-1.11 m. The initial temperature of the pool water varied from 11 deg. C to 63 deg. C, the steam flow rate from 290 g/s to 1220 g/s and the temperature of incoming steam from 132 deg. C to 182 deg. C. Non-condensables were pushed from the dry well into the gas space of the wet well with a short discharge of steam before the recorded period of the experiments. As a result of this procedure, the system pressure was at an elevated level in the beginning of the actual experiments. An increased counterpressure was used in the last experiment of the series. The diminishing effect of increased system pressure on chugging intensity and on measured loads is evident from the results of the last experiment. The highest pressure pulses both inside the blowdown pipe and in the condensation pool were about half of those measured with a lower system pressure but otherwise with similar test parameters. The experiments on dynamic loading gave expected results. The loads experienced by pool structures depended strongly on the steam mass flow rate, pool water temperature and system pressure. The DYN experiments indicated that chugging and condensation within the blowdown pipe cause significant dynamic loads in case of strongly sub-cooled pool water. The level of pool water temperature is decisive

  20. PPOOLEX experiments on dynamic loading with pressure feedback

    Energy Technology Data Exchange (ETDEWEB)

    Puustinen, M.; Laine, J.; Raesaenen, A. (Lappeenranta Univ. of Technology, Nuclear Safety Research Unit (Finland))

    2011-01-15

    This report summarizes the results of the dynamic loading experiments (DYN series) carried out with the scaled down, two compartment PPOOLEX test facility designed and constructed at LUT. Steam was blown into the dry well compartment and from there through the DN200 vertical blowdown pipe to the condensation pool filled with sub-cooled water. The main purpose of the experiments was to study dynamic loads caused by different condensation modes. Particularly, the effect of counterpressure on loads due to pressure oscillations induced by chugging was of interest. Before the experiments the condensation pool was filled with isothermal water so that the blowdown pipe outlet was submerged by 1.03-1.11 m. The initial temperature of the pool water varied from 11 deg. C to 63 deg. C, the steam flow rate from 290 g/s to 1220 g/s and the temperature of incoming steam from 132 deg. C to 182 deg. C. Non-condensables were pushed from the dry well into the gas space of the wet well with a short discharge of steam before the recorded period of the experiments. As a result of this procedure, the system pressure was at an elevated level in the beginning of the actual experiments. An increased counterpressure was used in the last experiment of the series. The diminishing effect of increased system pressure on chugging intensity and on measured loads is evident from the results of the last experiment. The highest pressure pulses both inside the blowdown pipe and in the condensation pool were about half of those measured with a lower system pressure but otherwise with similar test parameters. The experiments on dynamic loading gave expected results. The loads experienced by pool structures depended strongly on the steam mass flow rate, pool water temperature and system pressure. The DYN experiments indicated that chugging and condensation within the blowdown pipe cause significant dynamic loads in case of strongly sub-cooled pool water. The level of pool water temperature is decisive

  1. Molecular Dynamics Simulations of a Pressure-induced Glass Transition

    CERN Document Server

    Shumway, S L; Jonsson, H; Shumway, Shelly L.; Clarke, Andrew S.

    1994-01-01

    We simulate the compression of a two-component Lennard-Jones liquid at a variety of constant temperatures using a molecular dynamics algorithm in an isobaric-isothermal ensemble. The viscosity of the liquid increases with pressure, undergoing a broadened transition into a structurally arrested, amorphous state. This transition, like the more familiar one induced by cooling, is correlated with a significant increase in icosahedral ordering. In fact, the structure of the final state, as measured by an analysis of the bonding, is essentially the same in the glassy, frozen state whether produced by squeezing or by cooling under pressure. We have computed an effective hard-sphere packing fraction at the transition, defining the transition pressure or temperature by a cutoff in the diffusion constant, analogous to the traditional laboratory definition of the glass transition by an arbitrary, low cutoff in viscosity. The packing fraction at this transition point is not constant, but is consistently higher for runs c...

  2. Irrigation dynamics associated with positive pressure, apical negative pressure and passive ultrasonic irrigations: a computational fluid dynamics analysis.

    Science.gov (United States)

    Chen, José Enrique; Nurbakhsh, Babak; Layton, Gillian; Bussmann, Markus; Kishen, Anil

    2014-08-01

    Complexities in root canal anatomy and surface adherent biofilm structures remain as challenges in endodontic disinfection. The ability of an irrigant to penetrate into the apical region of a canal, along with its interaction with the root canal walls, will aid in endodontic disinfection. The aim of this study was to qualitatively examine the irrigation dynamics of syringe irrigation with different needle tip designs (open-ended and closed-ended), apical negative pressure irrigation with the EndoVac® system, and passive ultrasonic-assisted irrigation, using a computational fluid dynamics model. Syringe-based irrigation with a side-vented needle showed a higher wall shear stress than the open-ended but was localised to a small region of the canal wall. The apical negative pressure mode of irrigation generated the lowest wall shear stress, while the passive-ultrasonic irrigation group showed the highest wall shear stress along with the greatest magnitude of velocity.

  3. Dynamic CT in patients with normal pressure hydrocephalus

    Energy Technology Data Exchange (ETDEWEB)

    Horibe, Kunio; Akagi, Katsuhito; Go, Junto; Kohmura, Eiji; Yamazaki, Mami

    1984-11-01

    In order to elucidate the cerebral circulation before and after shunt in patients with normal pressure hydrocephalus(NPH), a comparative study of 12 cases was performed using dynamic CT. In the effective shunt group, blood flow in the frontal gray matter and PVL was improved. The improvement in PVL was particularly marked. On the other hand, in the non-effective group, blood flow in the frontal gray matter was reduced compared with that before operation. In regard to predicting the effectiveness of the shunt from the features of preoperative dynamic CT study in NPH, it is suggested that blood flow in the frontal gray matter was lower in the effective shunt group than in the non-effective group. This cerebral circulation study using dynamic CT, which can be easily manipulated, is non-invasive, and is thought to be a useful method when highly reproducible parameters are chosen. (Author).

  4. Molecular dynamics study of helium bubble pressure in titanium

    Science.gov (United States)

    Zhang, Bao-Ling; Wang, Jun; Hou, Qing

    2011-03-01

    In this paper, the pressure state of the helium bubble in titanium is simulated by a molecular dynamics (MD) method. First, the possible helium/vacancy ratio is determined according to therelation between the bubble pressure and helium/vacancy ratio; then the dependences of the helium bubble pressure on the bubble radius at different temperatures are studied. It is shown that the product of the bubble pressure and the radius is approximately a constant, a result justifying the pressure-radius relation predicted by thermodynamics-based theory for gas bubble. Furthermore, a state equation of the helium bubble is established based on the MD calculations. Comparison between the results obtained by the state equation and corresponding experimental data shows that the state equation can describe reasonably the state of helium bubble and thus could be used for Monte Carlo simulations of the evolution of helium bubble in metals. Project supported by the National Natural Science Foundation of China (Grant No. 10775101) and National Magnetic Confinement Fusion Program of China (Grant No. 2009GB106004).

  5. Molecular dynamics of water at high temperatures and pressures

    Science.gov (United States)

    Brodholt, John; Wood, Bernard

    1990-09-01

    There are currently no precise P-V-T data for water at pressures above 8.9 kbars and temperatures above 900°C. Many petrological processes in the lower crust and upper mantle take place under more extreme conditions, however and petrologists commonly rely on empirical equations of state such as the modified Redlich-Kwong equation (MRK) to extrapolate the low pressure data. In this study we have taken an alternative approach and attempted to simulate the P-V-T properties of water using molecular dynamics. The TIP4P intermolecular potential for H 2O ( JORGENSEN et al., 1983) has had considerable success predicting the properties of water at low temperatures and pressures up to 10 kbar ( MADURA et al., 1988). We have extended its application by making molecular dynamics (MD) simulations at a density of 1.0 g/cc from 300 to 2300 K and 0.5 to 40 kbars. The results agree with the P-V-T data of BURNHAM et al. (1969) (up to 10 kbars) with an average error of under 2%. This is a much better concordance than is obtained with any of the currently used versions of MRK. At 300 kbars and 2000 K the MD simulations predict densities within 8% of those obtained in the shock wave experiments of KORMER (1968). This is a very good agreement given the fact that water ionizes to some extent at high pressures ( MITCHELL and NELLIS, 1982) and we have made no provisions for this effect. We conclude that molecular dynamics simulations provide the possibility of estimating P-V-T properties in the upper mantle P-T regime with very good accuracy.

  6. Material dynamics under extreme conditions of pressure and strain rate

    Energy Technology Data Exchange (ETDEWEB)

    Remington, B A; Allen, P; Bringa, E; Hawreliak, J; Ho, D; Lorenz, K T; Lorenzana, H; Meyers, M A; Pollaine, S W; Rosolankova, K; Sadik, B; Schneider, M S; Swift, D; Wark, J; Yaakobi, B

    2005-09-06

    Solid state experiments at extreme pressures (10-100 GPa) and strain rates ({approx}10{sup 6}-10{sup 8}s{sup -1}) are being developed on high-energy laser facilities, and offer the possibility for exploring new regimes of materials science. These extreme solid-state conditions can be accessed with either shock loading or with a quasi-isentropic ramped pressure drive. Velocity interferometer measurements establish the high pressure conditions. Constitutive models for solid-state strength under these conditions are tested by comparing 2D continuum simulations with experiments measuring perturbation growth due to the Rayleigh-Taylor instability in solid-state samples. Lattice compression, phase, and temperature are deduced from extended x-ray absorption fine structure (EXAFS) measurements, from which the shock-induced {alpha}-{omega} phase transition in Ti and the {alpha}-{var_epsilon} phase transition in Fe are inferred to occur on sub-nanosec time scales. Time resolved lattice response and phase can also be measured with dynamic x-ray diffraction measurements, where the elastic-plastic (1D-3D) lattice relaxation in shocked Cu is shown to occur promptly (< 1 ns). Subsequent large-scale molecular dynamics (MD) simulations elucidate the microscopic dynamics that underlie the 3D lattice relaxation. Deformation mechanisms are identified by examining the residual microstructure in recovered samples. The slip-twinning threshold in single-crystal Cu shocked along the [001] direction is shown to occur at shock strengths of {approx}20 GPa, whereas the corresponding transition for Cu shocked along the [134] direction occurs at higher shock strengths. This slip-twinning threshold also depends on the stacking fault energy (SFE), being lower for low SFE materials. Designs have been developed for achieving much higher pressures, P > 1000 GPa, in the solid state on the National Ignition Facility (NIF) laser.

  7. Dynamic isolation technologies in negative pressure isolation wards

    CERN Document Server

    Xu, Zhonglin

    2017-01-01

    This book presents novel design principles and technologies for dynamic isolation based on experimental studies. These approaches have now become the local standard in Beijing and are currently being promoted for use nationwide. Further, the book provides details of measures and guidelines for the design process. Departing from the traditional understanding that isolation wards should be designed with high negative pressure, airtight doors and fresh air, it establishes the basis for designing biological clean rooms, including isolation wards, using a simple and convenient scientific approach. This book is intended for designers, engineers, researchers, hospital management staff and graduate students in heating ventilation air conditioning (HVAC), air cleaning technologies and related areas.

  8. Dynamic response of nuclear fuel assembly excited by pressure pulsations

    Directory of Open Access Journals (Sweden)

    Zeman V.

    2012-12-01

    Full Text Available The paper deals with dynamic load calculation of the hexagonal type nuclear fuel assembly caused by spatial motion of the support plates in the reactor core. The support plate motion is excited by pressure pulsations generated by main circulation pumps in the coolant loops of the primary circuit of the nuclear power plant. Slightly different pumps revolutions generate the beat vibrations which causes an amplification of fuel assembly component dynamic deformations and fuel rods coating abrasion. The cyclic and central symmetry of the fuel assembly makes it possible the system decomposition into six identical revolved fuel rod segments which are linked with central tube and skeleton by several spacer grids in horizontal planes.The modal synthesis method with condensation of the fuel rod segments is used for calculation of the normal and friction forces transmitted between fuel rods and spacer grids cells.

  9. Relaxation dynamics of lysozyme in solution under pressure: Combining molecular dynamics simulations and quasielastic neutron scattering

    Energy Technology Data Exchange (ETDEWEB)

    Calandrini, V. [Centre de Biophysique Moleculaire, Rue Charles Sadron, 45071 Orleans (France); Synchrotron Soleil, L' Orme de Merisiers, B.P. 48, 91192 Gif-sur-Yvette (France); Hamon, V. [Centre de Biophysique Moleculaire, Rue Charles Sadron, 45071 Orleans (France); Hinsen, K. [Centre de Biophysique Moleculaire, Rue Charles Sadron, 45071 Orleans (France); Synchrotron Soleil, L' Orme de Merisiers, B.P. 48, 91192 Gif-sur-Yvette (France); Calligari, P. [Centre de Biophysique Moleculaire, Rue Charles Sadron, 45071 Orleans (France); Institut Laue-Langevin, 6 Rue Jules Horowitz, B.P. 156, 38042 Grenoble (France); Laboratoire Leon Brillouin, CEA Saclay, 91191 Gif-sur-Yvette (France); Bellissent-Funel, M.-C. [Laboratoire Leon Brillouin, CEA Saclay, 91191 Gif-sur-Yvette (France); Kneller, G.R. [Centre de Biophysique Moleculaire, Rue Charles Sadron, 45071 Orleans (France); Synchrotron Soleil, L' Orme de Merisiers, B.P. 48, 91192 Gif-sur-Yvette (France)], E-mail: kneller@cnrs-orleans.fr

    2008-04-18

    This paper presents a study of the influence of non-denaturing hydrostatic pressure on the relaxation dynamics of lysozyme in solution, which combines molecular dynamics simulations and quasielastic neutron scattering experiments. We compare results obtained at ambient pressure and at 3 kbar. Experiments have been performed at pD 4.6 and at a protein concentration of 60 mg/ml. For both pressures we checked the monodispersity of the protein solution by small angle neutron scattering. To interpret the simulation results and the experimental data, we adopt the fractional Ornstein-Uhlenbeck process as a model for the internal relaxation dynamics of the protein. On the experimental side, global protein motions are accounted for by the model of free translational diffusion, neglecting the much slower rotational diffusion. We find that the protein dynamics in the observed time window from about 1 to 100 ps is slowed down under pressure, while its fractal characteristics is preserved, and that the amplitudes of the motions are reduced by about 20%. The slowing down of the relaxation is reduced with increasing q-values, where more localized motions are seen.

  10. Modeling plasma pressure anisotropy's effect on Saturn's global magnetospheric dynamics

    Science.gov (United States)

    Tilley, M.; Harnett, E. M.; Winglee, R.

    2014-12-01

    A 3D multi-fluid, multi-scale plasma model with a complete treatment of plasma pressure anisotropy is employed to study global magnetospheric dynamics at Saturn. Cassini has observed anisotropies in the Saturnian magnetosphere, and analyses have showed correlations between anisotropy and plasma convection, ring current structure and intensity, confinement of plasma to the equatorial plane, as well as mass transport to the outer magnetosphere. The energization and transport of plasma within Saturn's magnetosphere is impactful upon the induced magnetic environments and atmospheres of potentially habitable satellites such as Enceladus and Titan. Recent efforts to couple pressure anisotropy with 3D multi-fluid plasma modeling have shown a significant move towards matching observations for simulations of Earth's magnetosphere. Our approach is used to study the effects of plasma pressure anisotropy on global processes of the Saturnian magnetosphere such as identifying the effect of pressure anisotropy on the centrifugal interchange instability. Previous simulation results have not completely replicated all aspects of the structure and formation of the interchange 'fingers' measured by Cassini at Saturn. The related effects of anisotropy, in addition to those mentioned above, include contribution to formation of MHD waves (e.g. reduction of Alfvén wave speed) and formation of firehose and mirror instabilities. An accurate understanding of processes such as the interchange instability is required if a complete picture of mass and energy transport at Saturn is to be realized. The results presented here will detail how the inclusion of a full treatment of pressure anisotropy for idealized solar wind conditions modifies the interchange structure and shape of the tail current sheet. Simulation results are compared to observations made by Cassini.

  11. Bubble cloud dynamics in a high-pressure spherical resonator

    Science.gov (United States)

    Anderson, Phillip Andrew

    A bubble cloud is a population of bubbles confined to a region within a fluid. Bubble clouds play a large role in a variety of naturally occurring phenomena and man-made applications (e.g., ocean noise, cavitation damage, sonoluminescence, ultrasonic cleaning, drug delivery, lithotripsy). It is important, therefore, to understand the behavior of bubble clouds so that their effects may be enhanced or diminished as desired. This work explores and characterizes the properties of bubble clouds nucleated inside a high-pressure spherical acoustic resonator, in connection with recent interest in acoustic inertial confinement fusion (acoustic ICF). A laser system was developed to repeatably nucleate a cloud of bubbles inside the resonator. The resulting events were then observed, primarily with schlieren imaging methods. Preliminary studies of the bubble cloud dynamics showed the sensitivity of the initial cloud to nucleation parameters including the phase of nucleation, the laser energy, and the acoustic power. After many acoustic cycles, some bubble clouds are observed to evolve into a tight cluster. The formation of these clusters correlates with initial bubble distributions which have a large cloud interaction parameter, β. Cluster dynamics are seen to be largely driven by reconverging shock waves from previous collapses reflected from the resonator's interior surface. Initial expansion of the cluster boundary is on the order of 8 mm/µs and the maximum radius approaches 3 mm. Shock pressures are estimated to be > 10 GPa at a radius of 100 µm using weak shock theory.

  12. Constant pressure and temperature discrete-time Langevin molecular dynamics.

    Science.gov (United States)

    Grønbech-Jensen, Niels; Farago, Oded

    2014-11-21

    We present a new and improved method for simultaneous control of temperature and pressure in molecular dynamics simulations with periodic boundary conditions. The thermostat-barostat equations are built on our previously developed stochastic thermostat, which has been shown to provide correct statistical configurational sampling for any time step that yields stable trajectories. Here, we extend the method and develop a set of discrete-time equations of motion for both particle dynamics and system volume in order to seek pressure control that is insensitive to the choice of the numerical time step. The resulting method is simple, practical, and efficient. The method is demonstrated through direct numerical simulations of two characteristic model systems-a one-dimensional particle chain for which exact statistical results can be obtained and used as benchmarks, and a three-dimensional system of Lennard-Jones interacting particles simulated in both solid and liquid phases. The results, which are compared against the method of Kolb and Dünweg [J. Chem. Phys. 111, 4453 (1999)], show that the new method behaves according to the objective, namely that acquired statistical averages and fluctuations of configurational measures are accurate and robust against the chosen time step applied to the simulation.

  13. Quantum molecular dynamics simulations of beryllium at high pressures

    Science.gov (United States)

    Desjarlais, Michael; Knudson, Marcus

    2008-03-01

    The phase boundaries and high pressure melt properties of beryllium have been the subject of several recent experimental and theoretical studies. The interest is motivated in part by the use of beryllium as an ablator material in inertial confinement fusion capsule designs. In this work, the high pressure melt curve, Hugoniot crossings, sound speeds, and phase boundaries of beryllium are explored with DFT based quantum molecular dynamics calculations. The entropy differences between the various phases of beryllium are extracted in the vicinity of the melt curve and agree favorably with earlier theoretical work on normal melting. High velocity flyer plate experiments with beryllium targets on Sandia's Z machine have generated high quality data for the Hugoniot, bulk sound speeds, and longitudinal sound speeds. This data provides a tight constraint on the pressure for the onset of shock melting of beryllium and intriguing information on the solid phase prior to melt. The results of the QMD calculations and the experimental results will be compared, and implications for the HCP and BCC phase boundaries of beryllium will be presented.

  14. Combustion dynamics of low vapour pressure nanofuel droplets

    Science.gov (United States)

    Pandey, Khushboo; Chattopadhyay, Kamanio; Basu, Saptarshi

    2017-07-01

    Multiscale combustion dynamics, shape oscillations, secondary atomization, and precipitate formation have been elucidated for low vapour pressure nanofuel [n-dodecane seeded with alumina nanoparticles (NPs)] droplets. Dilute nanoparticle loading rates (0.1%-1%) have been considered. Contrary to our previous studies of ethanol-water blend (high vapour pressure fuel), pure dodecane droplets do not exhibit internal boiling after ignition. However, variation in surface tension due to temperature causes shape deformations for pure dodecane droplets. In the case of nanofuels, intense heat release from the enveloping flame leads to the formation of micron-size aggregates (of alumina NPS) which serve as nucleation sites promoting heterogeneous boiling. Three boiling regimes (A, B, and C) have been identified with varying bubble dynamics. We have deciphered key mechanisms responsible for the growth, transport, and rupture of the bubbles. Bubble rupture causes ejections of liquid droplets termed as secondary atomization. Ejection of small bubbles (mode 1) resembles the classical vapour bubble collapse mechanism near a flat free surface. However, large bubbles induce severe shape deformations as well as bulk oscillations. Rupture of large bubbles results in high speed liquid jet formation which undergoes Rayleigh-Plateau tip break-up. Both modes contribute towards direct fuel transfer from the droplet surface to flame envelope bypassing diffusion limitations. Combustion lifetime of nanofuel droplets consequently has two stages: stage I (where bubble dynamics are dominant) and stage II (formation of gelatinous mass due to continuous fuel depletion; NP agglomeration). In the present work, variation of flame dynamics and spatio-temporal heat release (HR) have been analysed using high speed OH* chemiluminescence imaging. Fluctuations in droplet shape and flame heat release are found to be well correlated. Droplet flame is bifurcated in two zones (I and II). Flame response is

  15. Error Propagation Dynamics of PIV-based Pressure Field Calculations: How well does the pressure Poisson solver perform inherently?

    Science.gov (United States)

    Pan, Zhao; Whitehead, Jared; Thomson, Scott; Truscott, Tadd

    2016-08-01

    Obtaining pressure field data from particle image velocimetry (PIV) is an attractive technique in fluid dynamics due to its noninvasive nature. The application of this technique generally involves integrating the pressure gradient or solving the pressure Poisson equation using a velocity field measured with PIV. However, very little research has been done to investigate the dynamics of error propagation from PIV-based velocity measurements to the pressure field calculation. Rather than measure the error through experiment, we investigate the dynamics of the error propagation by examining the Poisson equation directly. We analytically quantify the error bound in the pressure field, and are able to illustrate the mathematical roots of why and how the Poisson equation based pressure calculation propagates error from the PIV data. The results show that the error depends on the shape and type of boundary conditions, the dimensions of the flow domain, and the flow type.

  16. Error Propagation Dynamics of PIV-based Pressure Field Calculations: How well does the pressure Poisson solver perform inherently?

    CERN Document Server

    Pan, Zhao; Thomson, Scott; Truscott, Tadd

    2016-01-01

    Obtaining pressure field data from particle image velocimetry (PIV) is an attractive technique in fluid dynamics due to its noninvasive nature. The application of this technique generally involves integrating the pressure gradient or solving the pressure Poisson equation using a velocity field measured with PIV. However, very little research has been done to investigate the dynamics of error propagation from PIV-based velocity measurements to the pressure field calculation. Rather than measure the error through experiment, we investigate the dynamics of the error propagation by examining the Poisson equation directly. We analytically quantify the error bound in the pressure field, and are able to illustrate the mathematical roots of why and how the Poisson equation based pressure calculation propagates error from the PIV data. The results show that the error depends on the shape and type of boundary conditions, the dimensions of the flow domain, and the flow type.

  17. Error propagation dynamics of PIV-based pressure field calculations: How well does the pressure Poisson solver perform inherently?

    Science.gov (United States)

    Pan, Zhao; Whitehead, Jared; Thomson, Scott; Truscott, Tadd

    2016-08-01

    Obtaining pressure field data from particle image velocimetry (PIV) is an attractive technique in fluid dynamics due to its noninvasive nature. The application of this technique generally involves integrating the pressure gradient or solving the pressure Poisson equation using a velocity field measured with PIV. However, very little research has been done to investigate the dynamics of error propagation from PIV-based velocity measurements to the pressure field calculation. Rather than measure the error through experiment, we investigate the dynamics of the error propagation by examining the Poisson equation directly. We analytically quantify the error bound in the pressure field, and are able to illustrate the mathematical roots of why and how the Poisson equation based pressure calculation propagates error from the PIV data. The results show that the error depends on the shape and type of boundary conditions, the dimensions of the flow domain, and the flow type.

  18. Full Dynamic-Range Pressure Sensor Matrix Based on Optical and Electrical Dual-Mode Sensing.

    Science.gov (United States)

    Wang, Xiandi; Que, Miaoling; Chen, Mengxiao; Han, Xun; Li, Xiaoyi; Pan, Caofeng; Wang, Zhong Lin

    2017-01-06

    Pressure sensor matrix (PSM) with full dynamic range can accurately detect and spatially map pressure profile. A 100 × 100 large-scale PSM gives both electrical and optical signals by itself without applying an external power. The device represents a major step toward digital imaging and visible display of pressure distribution covers a large dynamic range.

  19. Whole-body mathematical model for simulating intracranial pressure dynamics

    Science.gov (United States)

    Lakin, William D. (Inventor); Penar, Paul L. (Inventor); Stevens, Scott A. (Inventor); Tranmer, Bruce I. (Inventor)

    2007-01-01

    A whole-body mathematical model (10) for simulating intracranial pressure dynamics. In one embodiment, model (10) includes 17 interacting compartments, of which nine lie entirely outside of intracranial vault (14). Compartments (F) and (T) are defined to distinguish ventricular from extraventricular CSF. The vasculature of the intracranial system within cranial vault (14) is also subdivided into five compartments (A, C, P, V, and S, respectively) representing the intracranial arteries, capillaries, choroid plexus, veins, and venous sinus. The body's extracranial systemic vasculature is divided into six compartments (I, J, O, Z, D, and X, respectively) representing the arteries, capillaries, and veins of the central body and the lower body. Compartments (G) and (B) include tissue and the associated interstitial fluid in the intracranial and lower regions. Compartment (Y) is a composite involving the tissues, organs, and pulmonary circulation of the central body and compartment (M) represents the external environment.

  20. Manifestation of constrained dynamics in a low pressure spark

    CERN Document Server

    Auluck, S K H

    2013-01-01

    Some features of neutron emission from dense plasma focus suggest that the participating deuterons have energy in the range of 105 eV and have a directionality of toroidal motion. Theoretical models of these devices assume that the plasma evolves through a purely irrotational flow and thus fail to predict such solenoidal flow on the scale of the plasma dimensions. Predictions of a relaxation theory are consistent with experimental data [S K H Auluck, Physics of Plasmas,18, 032508 (2011)], but the assumptions upon which it is based are not compatible with known features of these devices. There is thus no satisfactory theoretical construct which provides the necessity for solenoidal flow in these devices. This paper proposes such theoretical construct, namely, the principle of constrained dynamics, and describes an experiment which provides support for this idea. The experiment consisted of low inductance, self-breaking spark discharge in helium at a pressure ~100 hPa between two pointed electrodes separated by...

  1. Nonlinear radiation pressure dynamics in an optomechanical crystal

    CERN Document Server

    Krause, Alex G; Ludwig, Max; Safavi-Naeini, Amir H; Chan, Jasper; Marquardt, Florian; Painter, Oskar

    2015-01-01

    Utilizing a silicon nanobeam optomechanical crystal, we investigate the attractor diagram arising from the radiation pressure interaction between a localized optical cavity at $\\lambda = 1552$nm and a mechanical resonance at $\\omega/2\\pi = 3.72$GHz. At a temperature of $T \\approx 10$K, highly nonlinear driving of mechanical motion is observed via continuous wave optical pumping. Introduction of a time-dependent (modulated) optical pump is used to steer the system towards an otherwise inaccessible dynamically stable attractor in which mechanical self-oscillation occurs for an optical pump red-detuned from the cavity resonance. An analytical model incorporating thermo-optic effects due to optical absorption heating is developed, and found to accurately predict the measured device behavior.

  2. Evaluating road surface conditions using dynamic tire pressure sensor

    Science.gov (United States)

    Zhao, Yubo; Wu, H. Felix; McDaniel, J. Gregory; Wang, Ming L.

    2014-03-01

    In order to best prioritize road maintenance, the level of deterioration must be known for all roads in a city's network. Pavement Condition Index (PCI) and International Roughness Index (IRI) are two standard methods for obtaining this information. However, IRI is substantially easier to measure. Significant time and money could be saved if a method were developed to estimate PCI from IRI. This research introduces a new method to estimate IRI and correlate IRI with PCI. A vehicle-mounted dynamic tire pressure sensor (DTPS) system is used. The DTPS measures the signals generated from the tire/road interaction while driving. The tire/road interaction excites surface waves that travel through the road. DTPS, which is mounted on the tire's valve stem, measures tire/road interaction by analyzing the pressure change inside the tire due to the road vibration, road geometry and tire wall vibration. The road conditions are sensible to sensors in a similar way to human beings in a car. When driving on a smooth road, tire pressure stays almost constant and there are minimal changes in the DTPS data. When driving on a rough road, DTPS data changes drastically. IRI is estimated from the reconstructed road profile using DTPS data. In order to correlate IRI with PCI, field tests were conducted on roads with known PCI values in the city of Brockton, MA. Results show a high correlation between the estimated IRI values and the known PCI values, which suggests that DTPS-based IRI can provide accurate predictions of PCI.

  3. Dynamic CT study of normal-pressure hydrocephalus

    Energy Technology Data Exchange (ETDEWEB)

    Tamaki, Norihiko; Kojima, Noriaki; Shirakuni, Takayuki; Matsumoto, Satoshi

    1984-08-01

    A dynamic CT study was performed in 14 patients with presumed normal-pressure hydrocephalus, of which diagnosis had been made by clinical symptomatology, CT findings, the results of the continuous monitoring of intracranial pressure, and CT cisternographic findings. It is demonstrated by serial CT scans that the cerebral arteries and arterioles were initially filled with contrast media, which were followed by the symmetrical and homogeneous staining of the cortical gray matter and basal ganglia, the diencephalia, and then the white matter. The venous system was stained in the late phase. The contrast media was finally cleared out from the intracranial space. Thus, the staining of the cerebral vessels and brain parenchym showed a uniform pattern in all cases. Functional CT images revealed that the patients with normal-pressure hydrocephalus who responded well to the shunt procedure had areas of prolonged mean circulation time scattered diffusely not only in the paraventricular structures, but also in the cortical gray matter of all the cerebral hemispheres. Following the shunt procedure, the hemodynamic conditions improved in almost all the areas mentioned above, but especially in the frontal and temporal gray matters and the paraventricular structures. In the patients who did not benefit from the shunt operation, however, there was no special abnormality of hemodynamic distribution. The analysis of the mean circulation time in the region of interest demonstrated that a significant improvement in cerebral hemodynamics was noted in the regions of the frontal and temporal gray matters, the periventricular white matter, and the caudate nucleus in patients who benefitted from the shunt operation. In patients who did not improve after the ventriculo-peritoneal shunt, however, there was no statistically significant difference between pre- and post-shunt mean circulation times. (J.P.N.).

  4. Delocalization of Electrons in Strong Insulators at High Dynamic Pressures

    Directory of Open Access Journals (Sweden)

    William J. Nellis

    2011-06-01

    Full Text Available Systematics of material responses to shock flows at high dynamic pressures are discussed. Dissipation in shock flows drives structural and electronic transitions or crossovers, such as used to synthesize metallic liquid hydrogen and most probably Al2O3 metallic glass. The term “metal” here means electrical conduction in a degenerate system, which occurs by band overlap in degenerate condensed matter, rather than by thermal ionization in a non-degenerate plasma. Since H2 and probably disordered Al2O3 become poor metals with minimum metallic conductivity (MMC virtually all insulators with intermediate strengths do so as well under dynamic compression. That is, the magnitude of strength determines the split between thermal energy and disorder, which determines material response. These crossovers occur via a transition from insulators with electrons localized in chemical bonds to poor metals with electron energy bands. For example, radial extents of outermost electrons of Al and O atoms are 7 a0 and 4 a0, respectively, much greater than 1.7 a0 needed for onset of hybridization at 300 GPa. All such insulators are Mott insulators, provided the term “correlated electrons” includes chemical bonds.

  5. A combination of thermal methods to assess coronary pressure and flow dynamics with a pressure-sensing guide wire.

    Science.gov (United States)

    van der Horst, Arjen; Van't Veer, Marcel; van der Sligte, Robin A M; Rutten, Marcel C M; Pijls, Nico H J; van de Vosse, Frans N

    2013-03-01

    Measurement of coronary pressure and absolute flow dynamics have shown great potential in discerning different types of coronary circulatory disease. In the present study, the feasibility of assessing pressure and flow dynamics with a combination of two thermal methods, developed in combination with a pressure-sensor-tipped guide wire, was evaluated in an in vitro coronary model. A continuous infusion thermodilution method was employed to determine the average flow, whereas a thermal anemometric method was utilized to assess the pressure and flow dynamics, simultaneously. In the latter method, the electrical power supplied to an element, kept at constant temperature above ambient temperature, was used as a measure for the shear rate. It was found that, using a single calibration function, the method was able to assess coronary pressure and flow dynamics for different flow amplitudes, heart rates, and different pressure wires. However, due to the fact that the thermal anemometric method cannot detect local shear rate reversal, the method was unable to reliably measure flow dynamics close to zero. Nevertheless, the combined methodology was able to reliably assess diastolic hemodynamics. The diastolic peak flow and average diastolic resistance could be determined with a small relative error of (8 ± 7)% and (7 ± 5)%, respectively.

  6. Towards a shock tube method for the dynamic calibration of pressure sensors.

    Science.gov (United States)

    Downes, Stephen; Knott, Andy; Robinson, Ian

    2014-08-28

    In theory, shock tubes provide a pressure change with a very fast rise time and calculable amplitude. This pressure step could provide the basis for the calibration of pressure transducers used in highly dynamic applications. However, conventional metal shock tubes can be expensive, unwieldy and difficult to modify. We describe the development of a 1.4 MPa (maximum pressure) shock tube made from unplasticized polyvinyl chloride pressure tubing which provides a low-cost, light and easily modifiable basis for establishing a method for determining the dynamic characteristics of pressure sensors.

  7. Effect of temperature and pressure on the dynamics of nanoconfined propane

    Energy Technology Data Exchange (ETDEWEB)

    Gautam, Siddharth, E-mail: gautam.25@osu.edu; Liu, Tingting, E-mail: gautam.25@osu.edu; Welch, Susan; Cole, David [School of Earth Sciences, The Ohio State University, 275 Mendenhall Laboratory, 125 S Oval Mall, Columbus, OH 43210 (United States); Rother, Gernot [Geochemistry and Interfacial Science Group, Chemical Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Jalarvo, Niina [Jülich Center for Neutron Sciences (JCNS-1), Forschungszentrum Jülich Outstation at Spallation Neutron Source(SNS), Chemical and Engineering Materials Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Mamontov, Eugene [Spallation Neutron Source (SNS), Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

    2014-04-24

    We report the effect of temperature and pressure on the dynamical properties of propane confined in nanoporous silica aerogel studied using quasielastic neutron scattering (QENS). Our results demonstrate that the effect of a change in the pressure dominates over the effect of temperature variation on the dynamics of propane nano-confined in silica aerogel. At low pressures, most of the propane molecules are strongly bound to the pore walls, only a small fraction is mobile. As the pressure is increased, the fraction of mobile molecules increases. A change in the mechanism of motion, from continuous diffusion at low pressures to jump diffusion at higher pressures has also been observed.

  8. Geometry optimization for micro-pressure sensor considering dynamic interference.

    Science.gov (United States)

    Yu, Zhongliang; Zhao, Yulong; Li, Lili; Tian, Bian; Li, Cun

    2014-09-01

    Presented is the geometry optimization for piezoresistive absolute micro-pressure sensor. A figure of merit called the performance factor (PF) is defined as a quantitative index to describe the comprehensive performances of a sensor including sensitivity, resonant frequency, and acceleration interference. Three geometries are proposed through introducing islands and sensitive beams into typical flat diaphragm. The stress distributions of sensitive elements are analyzed by finite element method. Multivariate fittings based on ANSYS simulation results are performed to establish the equations about surface stress, deflection, and resonant frequency. Optimization by MATLAB is carried out to determine the dimensions of the geometries. Convex corner undercutting is evaluated. Each PF of the three geometries with the determined dimensions is calculated and compared. Silicon bulk micromachining is utilized to fabricate the prototypes of the sensors. The outputs of the sensors under both static and dynamic conditions are tested. Experimental results demonstrate the rationality of the defined performance factor and reveal that the geometry with quad islands presents the highest PF of 210.947 Hz(1/4). The favorable overall performances enable the sensor more suitable for altimetry.

  9. Dynamic Sublimation Pressure and the Catastrophic Breakup of Comet ISON

    CERN Document Server

    Steckloff, Jordan K; Bowling, Timothy; Melosh, H Jay; Minton, David; Lisse, Carey M; Battams, Karl

    2015-01-01

    Previously proposed mechanisms have difficulty explaining the disruption of Comet C/2012 S1 (ISON) as it approached the Sun. We describe a novel cometary disruption mechanism whereby comet nuclei fragment and disperse through dynamic sublimation pressure, which induces differential stresses within the interior of the nucleus. When these differential stresses exceed its material strength, the nucleus breaks into fragments. We model the sublimation process thermodynamically and propose that it is responsible for the disruption of Comet ISON. We estimate the bulk unconfined crushing strength of Comet ISON's nucleus and the resulting fragments to be 0.5 Pa and 1-9 Pa respectively, assuming typical Jupiter Family Comet (JFC) albedos. However, if Comet ISON has an albedo similar to Pluto, this strength estimate drops to 0.2 Pa for the intact nucleus and 0.6-4 Pa for its fragments. Regardless of assumed albedo, these are similar to previous strength estimates of JFCs. This suggests that, if Comet ISON is representat...

  10. High protein flexibility and reduced hydration water dynamics are key pressure adaptive strategies in prokaryotes

    KAUST Repository

    Martinez, N.

    2016-09-06

    Water and protein dynamics on a nanometer scale were measured by quasi-elastic neutron scattering in the piezophile archaeon Thermococcus barophilus and the closely related pressure-sensitive Thermococcus kodakarensis, at 0.1 and 40 MPa. We show that cells of the pressure sensitive organism exhibit higher intrinsic stability. Both the hydration water dynamics and the fast protein and lipid dynamics are reduced under pressure. In contrast, the proteome of T. barophilus is more pressure sensitive than that of T. kodakarensis. The diffusion coefficient of hydration water is reduced, while the fast protein and lipid dynamics are slightly enhanced with increasing pressure. These findings show that the coupling between hydration water and cellular constituents might not be simply a master-slave relationship. We propose that the high flexibility of the T. barophilus proteome associated with reduced hydration water may be the keys to the molecular adaptation of the cells to high hydrostatic pressure.

  11. High protein flexibility and reduced hydration water dynamics are key pressure adaptive strategies in prokaryotes

    Science.gov (United States)

    Martinez, N.; Michoud, G.; Cario, A.; Ollivier, J.; Franzetti, B.; Jebbar, M.; Oger, P.; Peters, J.

    2016-09-01

    Water and protein dynamics on a nanometer scale were measured by quasi-elastic neutron scattering in the piezophile archaeon Thermococcus barophilus and the closely related pressure-sensitive Thermococcus kodakarensis, at 0.1 and 40 MPa. We show that cells of the pressure sensitive organism exhibit higher intrinsic stability. Both the hydration water dynamics and the fast protein and lipid dynamics are reduced under pressure. In contrast, the proteome of T. barophilus is more pressure sensitive than that of T. kodakarensis. The diffusion coefficient of hydration water is reduced, while the fast protein and lipid dynamics are slightly enhanced with increasing pressure. These findings show that the coupling between hydration water and cellular constituents might not be simply a master-slave relationship. We propose that the high flexibility of the T. barophilus proteome associated with reduced hydration water may be the keys to the molecular adaptation of the cells to high hydrostatic pressure.

  12. Dynamic Foot Pressure as a Countermeasure to Muscle Atrophy

    Science.gov (United States)

    Kyparos, A.; Layne, C. S.; Martinez, D. A.; Clarke, M. S. F.; Feeback, D. L.

    2002-01-01

    Mechanical unloading of skeletal muscle (SKM) as a consequence of space flight or ground-based analogues, such as human bedrest and rodent hindlimb suspension (HLS) models, induces SKM atrophy particularly affecting the anti-gravity musculature of the lower limbs. In the context of manned space flight, the subsequent loss of muscle strength and functionality will pose operational implications jeopardizing mission success. Exercise, currently the primary muscle degradation countermeasure, has not proven completely effective in preventing muscle atrophy. It is therefore imperative that some other forms of in- flight countermeasure be also developed to supplement the prescribed exercise regimen the astronauts follow during spaceflight. Previous work in both humans and rats has shown that mechanical stimulation of the soles of the feet increases neuromuscular activation in the lower limb musculature and that such stimulation results in the limited prevention of atrophy in the soleus muscle of unloaded rats. This study was designed to investigate the effect of cutaneous mechanoreceptor stimulation on hindlimb unloading- induced SKM atrophy in rats. It was hypothesized that mechanical stimulation of the plantar surface of the rat foot during hindlimb suspension (HLS), utilizing a novel stimulation paradigm known as Dynamic Foot Pressure (DFP), would attenuate unloading-induced SKM atrophy. Mature adult male Wistar rats were randomly assigned to four groups of 10 rats each as follows: sedentary controls (Ctrl), hindlimb suspended only (HLS), hindlimb suspended wearing an inflatable boot (HLS-IFL) and hindlimb suspended rats wearing a non-inflatable boot (HLS-NIFL). The stimulation of mechanoreceptors was achieved by applying pressure to the plantar surface of the foot during the 10-day period of HLS using a custom-built boot. The anti-atrophic effects of DFP application was quantified directly by morphological (muscle wet weight, myofiber cross-sectional area

  13. Effect of change in large and fast solar wind dynamic pressure on geosynchronous magnetic field

    Institute of Scientific and Technical Information of China (English)

    Borodkova N L; Liu Jing-Bo; Huang Zhao-Hui; Zastenker G N; Wang Chi; Eiges P E

    2006-01-01

    We present a comparison of changes in large and sharp solar wind dynamic pressure, observed by several spacecraft,with fast disturbances in the magnetospheric magnetic field, measured by the geosynchronous satellites. More than 260 changes in solar wind pressure during the period 1996-2003 are selected for this study. Large statistics show that an increase (a decrease) in dynamic pressure always results in an increase (a decrease) in the magnitude of geosynchronous magnetic field. The amplitude of response to the geomagnetic field strongly depends on the location of observer relative to the noon meridian, the value of pressure before disturbance, and the change in amplitude of pressure.

  14. Effect of the shape of mouth pressure variation on dynamic oscillation threshold of a clarinet model

    CERN Document Server

    Bergeot, Baptiste; Vergez, Christophe

    2014-01-01

    Simple models of clarinet instruments based on iterated maps have been used in the past to successfully estimate the threshold of oscillation of this instrument as a function of a constant blowing pressure. However, when the blowing pressure gradually increases through time, the oscillations appear at a much higher value, called dynamic oscillation threshold, than what is predicted in the static case. This is known as bifurcation delay, a phenomenon studied in [1,2] for a clarinet model. In particular the dynamic oscillation threshold is predicted analytically when the blowing pressure is linearly increased. However, the mouth pressure cannot grow indefinitely. During a note attack, after an increasing phase, the musician stabilizes the mouth pressure. In the present work, the analytical prediction of the dynamic oscillation threshold is extended to a situations in which the mouth pressure approaches a steady state pressure according to an exponential time profile. The predictions still show a good agreement ...

  15. Change in blood pressure in recovery phase after combined (static & dynamic) exercise

    OpenAIRE

    桑村, 由美; 志内, 哲也; 野村, 千景; 幸田, 貴美子; 小原, 繁

    1997-01-01

    It is well known that systolic blood pressure (SBP) elevate but diastolic blood pressure (DBP) do not elevate during dynamic exercise and in statlc isometrlc exercise DBP show respectable elevation. However,changes in SBP and DBP in recovery phase after exercise is unclear.In this study we measured SBP and DBP by auscultatory recording method during recovery phase for 10 minutes. Resting blood pressure was determined immediately before exercise. The exercise was a dynamic (p...

  16. Ab-initio molecular dynamics simulation on nano-system under external pressure

    Institute of Scientific and Technical Information of China (English)

    JI; Min; SUN; Deyan; GONG; Xingao

    2004-01-01

    A new constant-pressure molecular dynamics (MD) method is developed to simulate the dynamic behavior and structure transition of finite system under external pressure. In this method, no artificial parameter is introduced and the computation overheads are very small. As an application, a hard-soft transition of single wall carbon nanotube (SWCNT) under external pressure is found, which is in agreement with the experiments.

  17. A new dynamic method for measuring hydrogen partial pressure in molten aluminum alloy

    Directory of Open Access Journals (Sweden)

    Sun Qian

    2011-02-01

    Full Text Available Hydrogen partial pressure is an important parameter to calculate hydrogen concentration levels in molten aluminum alloy. A new dynamic method for measuring hydrogen partial pressure in molten aluminum alloy is studied. Dynamic and rapid measurement is realized through changing the volume of the vacuum chamber and calculating the pressure difference ΔP between the theoretical and measured pressures in the vacuum chamber. Positive ΔP indicates hydrogen transmits from melt to vacuum chamber and negative ΔP means the reverse. When ΔP is equal to zero, hydrogen transmitted from both sides reached a state of dynamical equilibrium and the pressure in the vacuum chamber is equal to the hydrogen partial pressure in the molten aluminum alloy. Compared with other existing measuring methods, the new method can significantly shorten the testing time and reduce measuring cost.

  18. Novel Method for Processing the Dynamic Calibration Signal of Pressure Sensor

    Directory of Open Access Journals (Sweden)

    Zhongyu Wang

    2015-07-01

    Full Text Available Dynamic calibration is one of the important ways to acquire the dynamic performance parameters of a pressure sensor. This research focuses on the processing method for the output of calibrated pressure sensor, and mainly attempts to solve the problem of extracting the true information of step response under strong interference noise. A dynamic calibration system based on a shock tube is established to excite the time-domain response signal of a calibrated pressure sensor. A key processing on difference modeling is applied for the obtained signal, and several generating sequences are established. A fusion process for the generating sequences is then undertaken, and the true information of the step response of the calibrated pressure sensor can be obtained. Finally, by implementing the common QR decomposition method to deal with the true information, a dynamic model characterizing the dynamic performance of the calibrated pressure sensor is established. A typical pressure sensor was used to perform calibration tests and a frequency-domain experiment for the sensor was also conducted. Results show that the proposed method could effectively filter strong interference noise in the output of the sensor and the corresponding dynamic model could effectively characterize the dynamic performance of the pressure sensor.

  19. Novel Method for Processing the Dynamic Calibration Signal of Pressure Sensor.

    Science.gov (United States)

    Wang, Zhongyu; Li, Qiang; Wang, Zhuoran; Yan, Hu

    2015-07-21

    Dynamic calibration is one of the important ways to acquire the dynamic performance parameters of a pressure sensor. This research focuses on the processing method for the output of calibrated pressure sensor, and mainly attempts to solve the problem of extracting the true information of step response under strong interference noise. A dynamic calibration system based on a shock tube is established to excite the time-domain response signal of a calibrated pressure sensor. A key processing on difference modeling is applied for the obtained signal, and several generating sequences are established. A fusion process for the generating sequences is then undertaken, and the true information of the step response of the calibrated pressure sensor can be obtained. Finally, by implementing the common QR decomposition method to deal with the true information, a dynamic model characterizing the dynamic performance of the calibrated pressure sensor is established. A typical pressure sensor was used to perform calibration tests and a frequency-domain experiment for the sensor was also conducted. Results show that the proposed method could effectively filter strong interference noise in the output of the sensor and the corresponding dynamic model could effectively characterize the dynamic performance of the pressure sensor.

  20. The correlations of ions density with geomagnetic activity and solar dynamic pressure in cusp region

    Institute of Scientific and Technical Information of China (English)

    GUO JianGuang; SHI JianKui; ZHANG TieLong; LIU ZhenXing; A. FAZAKERLEY; H. R(E)ME; Ⅰ. DANDOURAS; E. LUCEK

    2007-01-01

    A statistical study of the properties of ions (O+, He+ and H+) measured by the Cluster-Ⅱ in cusp region as a function of the solar wind dynamic pressure and geomagnetic index Kp respectively was made during the summer and fall of 2001 -2003. The main results are that: (1) O+ ion density responds in a significant way to geomagnetic index Kp, and He+ ion density is not correlated with geomagnetic index Kp,both of them have a significant positive correlation with solar wind dynamic pressure; (2) H+ ion density is also observed to increase with solar wind dynamic pressure, and not correlated with geomagnetic index Kp.

  1. Dynamical analysis of high-pressure supercritical carbon dioxide jet in well drilling

    Institute of Scientific and Technical Information of China (English)

    DU Yu-kun; WANG Rui-he; NI Hong-jian; HUANG Zhi-yuan; LI Mu-kun

    2013-01-01

    This paper presents the design of an experimental setup and mathematical and physical models to determine the dynamical characteristics of the high-pressure supercritical carbon dioxide (SC-CO2) jet with a highly potential applications in the well drilling.The effects of three major factors on the wellbore dynamical characteristics of the high-pressure SC-CO2 jet,i.e.,the nozzle diameter,the standoff distance and the jet pressure are determined.It is indicated that the pressure of CO2 reduces severely in the SC-CO2 jet impact process.It is also found that the bottom-hole pressure and the temperature increase as the nozzle diameter increases but decrease with the increase of the standoff distance.The higher the jet pressure at the wellbore inlet is,the higher the pressure and the lower the temperature at the bottom-hole will be.

  2. High Speed Pressure Sensitive Paint for Dynamic Testing

    Science.gov (United States)

    Pena, Carolina; Chism, Kyle; Hubner, Paul

    2016-11-01

    Pressure sensitive paint (PSP) allows engineers to obtain accurate, high-spatial-resolution measurements of pressure fields over a structure. The pressure is directly related to the luminescence emitted by the paint due to oxygen quenching. Fast PSP has a higher surface area due to its porosity compared to conventional PSP, which enables faster diffusion and measurements to be acquired three orders of magnitude faster than with conventional PSP. A fast time response is needed when testing vibrating structures due to fluid-structure interaction. The goal of this summer project was to set-up, test and analyze the pressure field of an impinging air jet on a vibrating cantilever beam using Fast PSP. Software routines were developed for the processing of the emission images, videos of a static beam coated with Fast PSP were acquired with the air jet on and off, and the intensities of these two cases were ratioed and calibrated to pressure. Going forward, unsteady pressures on a vibrating beam will be measured and presented. Eventually, the long-term goal is to integrate luminescent pressure and strain measurement techniques, simultaneously using Fast PSP and a luminescent photoelastic coating on vibrating structures. Funding from NSF REU site Grant EEC 1358991 is greatly appreciated.

  3. Analysis of dynamic foot pressure distribution and ground reaction forces

    Science.gov (United States)

    Ong, F. R.; Wong, T. S.

    2005-04-01

    The purpose of this study was to assess the relationship between forces derived from in-shoe pressure distribution and GRFs during normal gait. The relationship served to demonstrate the accuracy and reliability of the in-shoe pressure sensor. The in-shoe pressure distribution from Tekscan F-Scan system outputs vertical forces and Centre of Force (COF), while the Kistler force plate gives ground reaction forces (GRFs) in terms of Fz, Fx and Fy, as well as vertical torque, Tz. The two systems were synchronized for pressure and GRFs measurements. Data was collected from four volunteers through three trials for both left and right foot under barefoot condition with the in-shoe sensor. The forces derived from pressure distribution correlated well with the vertical GRFs, and the correlation coefficient (r2) was in the range of 0.93 to 0.99. This is a result of extended calibration, which improves pressure measurement to give better accuracy and reliability. The COF from in-shoe sensor generally matched well with the force plate COP. As for the maximum vertical torque at the forefoot during toe-off, there was no relationship with the pressure distribution. However, the maximum torque was shown to give an indication of the rotational angle of the foot.

  4. Prediction of the dynamic oscillation threshold in a clarinet model with a linearly increasing blowing pressure

    CERN Document Server

    Bergeot, Baptiste; Vergez, Christophe; Gazengel, Bruno

    2012-01-01

    Reed instruments are modeled as self-sustained oscillators driven by the pressure inside the mouth of the musician. A set of nonlinear equations connects the control parameters (mouth pressure, lip force) to the system output, hereby considered as the mouthpiece pressure. Clarinets can then be studied as dynamical systems, their steady behavior being dictated uniquely by the values of the control parameters. Considering the resonator as a lossless straight cylinder is a dramatic yet common simplification that allows for simulations using nonlinear iterative maps. In this paper, we investigate analytically the effect of a time-varying blowing pressure on the behavior of this simplified clarinet model. When the control parameter varies, results from the so-called dynamic bifurcation theory are required to properly analyze the system. This study highlights the phenomenon of bifurcation delay and defines a new quantity, the dynamic oscillation threshold. A theoretical estimation of the dynamic oscillation thresho...

  5. Molecular dynamics of liquid SiO2 under high pressure

    Science.gov (United States)

    Rustad, James R.; Yuen, David A.; Spera, Frank J.

    1990-01-01

    The molecular dynamics of pure SiO2 liquids was investigated up to pressures of 20 GPa at 4000 K using 252, 498, 864, and 1371 particles. The results obtained suggest that the pressure-induced maxima in the self-diffusion coefficients of both oxygen and silicon are dependent on the system size. In the case of larger systems, the maximum decreases and shifts to lower pressures. Changes in the velocity autocorrelation function with increasing pressure are described. The populations of anomalously coordinated silicon and oxygen are then discussed as a function of pressure and system size.

  6. Molecular dynamics of liquid SiO2 under high pressure

    Science.gov (United States)

    Rustad, James R.; Yuen, David A.; Spera, Frank J.

    1990-01-01

    The molecular dynamics of pure SiO2 liquids was investigated up to pressures of 20 GPa at 4000 K using 252, 498, 864, and 1371 particles. The results obtained suggest that the pressure-induced maxima in the self-diffusion coefficients of both oxygen and silicon are dependent on the system size. In the case of larger systems, the maximum decreases and shifts to lower pressures. Changes in the velocity autocorrelation function with increasing pressure are described. The populations of anomalously coordinated silicon and oxygen are then discussed as a function of pressure and system size.

  7. Experimental investigation of dynamic effects in capillary pressure: Grain size dependency and upscaling

    Science.gov (United States)

    Camps-Roach, Geremy; O'Carroll, Denis M.; Newson, Timothy A.; Sakaki, Toshihiro; Illangasekare, Tissa H.

    2010-08-01

    The macroscopic flow equations used to predict two-phase flow typically utilizes a capillary pressure-saturation relationship determined under equilibrium conditions. Theoretical reasoning, experimental evidence, and numerical modeling results have indicated that when one fluid phase replaces another fluid, this relationship may not be unique but may depend on the rate at which the phase saturations change in response to changes in phase pressures. This nonuniqueness likely depends on a variety of factors including soil-fluid properties and possibly physical scale. To quantify this dependency experimentally, direct measurements of equilibrium and dynamic capillary pressure-saturation relationships were developed for two Ottawa sands with different grain sizes using a 20 cm long column. A number of replicate air-water experiments were conducted to facilitate statistical comparison of capillary pressure-saturation relationships. Water and air pressures and phase saturations were measured at three different vertical locations in the sand column under different desaturation rates (1) to measure local capillary pressure-saturation relationships (static and dynamic); (2) to quantify the dynamic coefficient τ, a measure of the magnitude of observed dynamic effects, as a function of water saturation for different grain sizes and desaturation rates; (3) to investigate the importance of grain size on measured dynamic effects; and (4) to assess the importance of sample scale on the magnitude of dynamic effects in capillary pressure. A comparison of the static and dynamic Pc-Sw relationships showed that at a given water saturation, capillary pressure measured under transient water drainage conditions is statistically larger than capillary pressure measured under equilibrium or static conditions, consistent with thermodynamic theory. The dynamic coefficient τ, used in the expression relating the static and dynamic capillary pressures to the desaturation rate was dependant on

  8. Simulation Study of AC Contactor Dynamic Contacts Contact Pressure Based on ADAMS

    Directory of Open Access Journals (Sweden)

    Gu Yungao

    2015-01-01

    Full Text Available A multi-body dynamics simulation model of CJ20-25 AC contactor was established with Pro/E(Pro/Engineerin this paper. A coupling simulation with machine, electric, magnetic on the contactor has been achieved in this model. Dynamic parameters which were called use the secondary development technology of ADAMS. The dynamic contact pressure signal of an AC contactor was obtained with ADAMS’s own simultaneous solution such as electromagnetic suction, kinematics and dynamics equations. The simulation results and actual measurement of contactor contact pressure signals are very similar. However, the complexity of the measured contacts vibration is greater than the simulation results because the actual working condition is more complex. This result provides a theoretical foundation to the dynamic contacts contact pressure test.

  9. Anisotropic pressure molecular dynamics for atomic fluid systems

    Energy Technology Data Exchange (ETDEWEB)

    Romero-Bastida, M [Facultad de Ciencias, Universidad Autonoma del Estado de Morelos, Avenida Universidad 1001, Chamilpa, Cuernavaca, Morelos 62209 (Mexico); Lopez-Rendon, R [Departamento de QuImica, Universidad Autonoma Metropolitana-Iztapalapa, Av San Rafael Atlixco 186, 09340 Mexico DF (Mexico)

    2007-07-20

    The MTK equations (Martyna G J, Tobias D J and Klein M L 1994 J. Chem. Phys. 101 4177-89), which simulate the constant-pressure, constant-temperature NPT ensemble, have been modified to simulate an anisotropic pressure along a single coordinate axis, thus rendering the NP{sub zz}T ensemble. The necessary theory of non-Hamiltonian systems is briefly reviewed in order to analytically prove that the proposed equations indeed sample the desired ensemble. A previously derived geometric integrator for the MTK equations is modified to take into account the anisotropic pressure and volume fluctuations. We choose a Lennard-Jones fluid as an illustrative example. The density distribution function, as well as various thermodynamic and interfacial properties of the model system in a liquid-vapour coexistence state, was computed to test the robustness of the proposed equations of motion to simulate the NP{sub zz}T ensemble.

  10. Static and dynamic tensile behaviour of aluminium processed by high pressure torsion

    NARCIS (Netherlands)

    Verleysen, P.; Oelbrandt, W.; Naghdy, S.; Kestens, L.

    2015-01-01

    High pressure torsion (HPT) is a severe plastic deformation technique in which a small, disk-like sample is subjected to a torsional deformation under a high hydrostatic pressure. In present study, the static and dynamic tensile behaviour of commercially pure aluminium (99.6 wt%) processed by HPT is

  11. Comparison of Iterative Methods for Computing the Pressure Field in a Dynamic Network Model

    DEFF Research Database (Denmark)

    Mogensen, Kristian; Stenby, Erling Halfdan; Banerjee, Srilekha

    1999-01-01

    In dynamic network models, the pressure map (the pressure in the pores) must be evaluated at each time step. This calculation involves the solution of a large number of nonlinear algebraic systems of equations and accounts for more than 80 of the total CPU-time. Each nonlinear system requires...

  12. Application backwards characteristics analysis method to dynamic response of metals under high pressure

    Directory of Open Access Journals (Sweden)

    Pan Hao

    2015-01-01

    Full Text Available Dynamic yield strength of metals/alloys depends on loading pressure and rates sensitively. With the development of laser interferometer measurement system, extracting strength information from window/free surface velocity profiles in shock and ramp loading experiments is becoming an important method to investigate materials’ dynamic response under high pressure and high strain rates. Backwards characteristics analysis method (BCAM can analyze the velocity profiles more reasonable because it accounts for bending of the incoming characteristics due to impedance mismatch between the sample and window. Synthetic analyses of reverse impact experiment and graded-density impactor loading-releasing experiment suggest that BCAM can give more accurate results including sound speed-particle velocity and yield strength at high pressure than incremental impedance matching method. We use BCAM to analyze velocity profiles of Sn in shock-release experiments and obtain its shear modulus and yield strength at different shock pressure and investigate its phase transition and dynamic unloading response.

  13. A stochastic model for the indicated pressure process and the dynamics of the internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Rizzoni, G. (Michigan Univ., Ann Arbor, MI (USA). Dept. of Electrical Engineering and Computer Science)

    1989-08-01

    In-cylinder gas pressure has long been recognized as a fundamental measure of performance in the internal combustion engine. Among the issues that have been the subject of research in recent years is the study of the effects cyclic combustion variability has on the cycle-to-cycle and cylinder-to-cylinder fluctuations in combustion pressures. Some of the research problems pertaining to cyclic combustion variability are to reformulate from a perspective markedly different from the fluid dynamic and thermodynamic models which traditionally characterize this research: a system viewpoint is embraced to construct a stochastic model for the indicated pressure process and the dynamics of the internal combustion engine. First a deterministic model for the dynamics of the engine is described; then a stochastic model is proposed for the cylinder pressure process. The deterministic model and the stochastic representation are then tied together in a Kalman filter model. Experimental results are discussed to validate the models.

  14. Dynamic Pressure of Seabed around Buried Pipelines in Shallow Water

    OpenAIRE

    Changjing Fu; Guoying Li; Tianlong Zhao; Donghai Guan

    2015-01-01

    Due to the obvious nonlinear effect caused by the shallow waves, the nonlinear wave loads have a great influence on the buried pipelines in shallow water. In order to ensure their stability, the forces on the pipelines that resulted from nonlinear waves should be considered thoroughly. Based on the Biot consolidation theory and the first-order approximate cnoidal wave theory, analytical solutions of the pore water pressure around the buried pipelines in shallow water caused by waves are first...

  15. Analysis of pressure wave dynamics in fuel rail system

    Directory of Open Access Journals (Sweden)

    B Alzahabi

    2008-09-01

    Full Text Available A model of an amplified common rail fuel system is simulated in Matlab toanalyze the wave mechanics in the rail. The injectors are modeled as asystem of linear and non-linear ODE’s consisting of masses, a helical spring,compressibility effects from fluid volumes, and hydraulic flow throughorifices. The injector simulation then predicts the rate of oil consumption,which is then input into the rail model.The rail is modeled in three sections which are coupled together. The pointswhere the coupling occurs are the locations where the current firinginjector and the pump supply are connected to the rail. This allows themodel to control the pressure and velocity (as boundary conditions atthese points. The rail model is based on the 1D, undamped wave equation,in a non-dimensional form [1] (in the position variable, x. The Reduction ofOrder method was used to solve the wave equation with the Matlabfunction PDEPE.The model was run with two different sets of initial conditions - nominal(constant pressure and zero velocity, and worst case using a simplifiedrepresentation of the pressure and velocity distribution at start of injection.This was done to determine the effect of rail waves at the start of injection,on the output of the model. The variation in fuel delivery, due to the variationin rail pressure, was then evaluated at three operating conditions - Idle,Peak Torque (PT and High Speed Light Load (HSLL. The simulation outputis then compared to analytical solutions of two forms of simplifiedgeometry, using the product method to solve the system [1.

  16. Implications of Dynamic Pressure Transducer Mounting Variations on Measurements in Pyrotechnic Test Apparatus

    Science.gov (United States)

    Dibbern, Andreas; Crisafulli, Jeffrey; Hagopia, Michael; McDougle, Stephen H.; Saulsberry, Regor L.

    2009-01-01

    Accurate dynamic pressure measurements are often difficult to make within small pyrotechnic devices, and transducer mounting difficulties can cause data anomalies that lead to erroneous conclusions. Delayed initial pressure response followed by data ringing has been observed when using miniaturized pressure transducer mounting adapters required to interface transducers to small test chambers. This delayed pressure response and ringing, combined with a high data acquisition rate, has complicated data analysis. This paper compares the output signal characteristics from different pressure transducer mounting options, where the passage distance from the transducer face to the pyrotechnic chamber is varied in length and diameter. By analyzing the data and understating the associated system dynamics, a more realistic understanding of the actual dynamic pressure variations is achieved. Three pressure transducer mounting configurations (elongated, standard, and face/flush mount) were simultaneously tested using NASA standard initiators in closed volume pressure bombs. This paper also presents results of these pressure transducer mounting configurations as a result of a larger NASA Engineering and Safety Center pyrovalve test project. Results from these tests indicate the improved performance of using face/flush mounted pressure transducers in this application. This type of mounting improved initial pressure measurement response time by approximately 19 s over standard adapter mounting, eliminating most of the lag time; provided a near step-function type initial pressure increase; and greatly reduced data ringing in high data acquisition rate systems. The paper goes on to discuss other issues associated with the firing and instrumentation that are important for the tester to understand.

  17. Conversion of Dynamic High Pressures from Air to Water for a Spherical TNT Charge

    Directory of Open Access Journals (Sweden)

    A. K. Sharma

    1996-01-01

    Full Text Available A numerical method has been applied to convert the dynamic high pressures from air-to-water for a spherical TNT charge. Standard equation of scaling law in air for TNT has been utilised to make the necessary conversions. The investigations have been made by taking into consideration the ambient pressure values for the two media. The calculations have been performed under the scaled distances to get better results. Experimental measurements using indigenous blast pressure gauge have been undertaken by detonating spherical charges of TNT under the same scaled distances in water to check the correctness of results and direct application of this method. A fairly close agreement between the theoretically computed and the experimental values of the dynamic high pressures shows the practical utility of this approach in that it enables an estimate of the experimental shock wave pressures, without conducting underwater experiments.

  18. Analysis and numerical simulation of dynamic effect on rock under high pressure water jet

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-hong; SI Hu; WANG Dan-dan

    2008-01-01

    Based on continuum mechanics and rock dynamics, analyzed the micro-structure damage of rock and the impulsive effect under high pressure water jet and developed the dynamic model. Further, on the assumption of that rock was homogeneous and isotropic, a computational model was established based on nonlinear finite element and Arbitrary Lagrangian-Eulerian(ALE) method. The dynamic effect impacted on rock under high pressure water jet was simulated by the dynamic contact method. The propagation of stress wave in rock was numerically simulated at different impacting velocity. The results show that the propagation velocity of stress wave is proportional to the impacting velocity of high pressure water jet. The faster the impacting velocity is, the quicker the comedown of stress wave.

  19. Pressure-produced ionization of nonideal plasma in a megabar range of dynamic pressures

    NARCIS (Netherlands)

    Fortov, VE; Ternovoi, VY; Zhernokletov, MV; Mochalov, MA; Mikhailov, AL; Filimonov, AS; Pyalling, AA; Mintsev, VB; Gryaznov, VK; Iosilevskii, IL

    2003-01-01

    The low-frequency electrical conductivity of strongly nonideal hydrogen, helium, and xenon plasmas was measured in the megabar range of pressures. The plasmas in question were generated by the method of multiple shock compression in planar and cylindrical geometries, whereby it was possible to reduc

  20. Dynamic effects of high-pressure pulsed water jet in low-permeability coal seams

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-hong; ZHOU Dong-ping; LU Yi-yu; KANG Yong; ZHAO Yu; WANG Xiao-chuan

    2009-01-01

    Mine gas extraction in China is difficult due to the characteristics such as mi-cro-porosity, low-permeability and high adsorption of coal seams. The pulsed mechanism of a high-pressure pulsed water jet was studied through theoretical analysis, experiment and field measurement. The results show that high-pressure pulsed water jet has three dynamic properties. What's more, the three dynamic effects can be found in low-perme-ability coal seams. A new pulsed water jet with 200-1 000 Hz oscillation frequency and peak pressure 2.5 times than average pressure was introduced. During bubble collapsing, sound vibration and instantaneous high pressures over 100 MPa enhanced the cutting ability of the high-pressure jet. Through high-pressure pulsed water jet drilling and slotting, the exposure area of coal bodies was greatly enlarged and pressure of the coal seams rapidly decreased. Therefore, the permeability of coal seams was improved and gas ab-sorption rate also decreased. Application results show that gas adsorption rate decreased by 30%-40% and the penetrability coefficient increased 100 times. This proves that high-pressure pulsed water is more efficient than other conventional methods.

  1. Dynamic response of vaporizing droplet to pressure oscillation

    Science.gov (United States)

    Yuan, Lei; Shen, Chibing; Zhang, Xinqiao

    2017-02-01

    Combustion instability is a major challenge in the development of the liquid propellant engines, and droplet vaporization is viewed as a potential mechanism for driving instabilities. Based on the previous work, an unsteady droplet heating and vaporization model was developed. The model and numerical method are validated by experimental data available in literature, and then the oscillatory vaporization of n-Heptane droplet exposed to unsteady harmonic nitrogen atmosphere was numerically investigated over a wide range of amplitudes and frequencies. Also, temperature variations inside the droplet were demonstrated under oscillation environments. It was found that the thermal wave is attenuated with significantly reduced wave intensities as it penetrates deep into droplet from the ambient gas. Droplet surface temperature exhibits smaller fluctuation than that of the ambient gas, and it exhibits a time lag with regard to the pressure variation. Furthermore, the mechanism leading to phase lag of vaporization rate with respect to pressure oscillation was unraveled. Results show that this phase lag varies during the droplet lifetime and it is strongly influenced by oscillation frequency, indicating droplet vaporization is only capable of driving combustion instability in some certain frequency domains. Instead, the amplitude of the oscillation does not have very significant effects. It is noteworthy that thermal inertia of the droplet also plays a considerable role in determining the phase lag.

  2. Correlation of intraluminal esophageal pressure with the dynamic extension of tracheoesophageal voice in total laryngectomees

    Directory of Open Access Journals (Sweden)

    Nathália Reis

    2013-05-01

    Full Text Available PURPOSE: To evaluate and correlate the amplitude of esophageal contractions triggered by swallowing water with dynamic extension and habitual, strong and weak sound intensity in total laryngectomees wearing a tracheoesophageal prosthesis. METHODS: Thirty total laryngectomees using tracheoesophageal voice with a phonatory prosthesis were evaluated by measuring the amplitude of contractions in the proximal, middle and distal esophagus and the pressure of the pharyngoesophageal transition by manometry. In order to measure vocal intensity the subject was asked to emit phonation of the vowel /a/ at habitual, strong and weak intensity which was captured with a sound pressure meter. Dynamic extension was calculated by subtracting strong intensity from weak intensity. RESULTS: A positive correlation was observed between contraction amplitude and dynamic extension in the proximal (rho: 0.45; p=0.01 and distal (rho: 0.41; p=0.02 esophagus There was no correlation with other parameters.. Total laryngectomees wearing a phonatory prosthesis with a dynamic extension above 21 dBNPS had greater contraction amplitude than laryngectomees with a dynamic extension below this value. CONCLUSIONS: There was a positive correlation between pressure amplitude in the proximal and distal esophagus and increased dynamic extension. The individuals with normal dynamic extension had greater contraction amplitude in the proximal esophagus than individuals with dynamic extension lower than the expected values for age.

  3. Evaluation of Dynamic Soil-Structure Interaction and Dynamic Seismic Soil Pressures Acting on It Subjected to Strong Earthquake Motions

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In order to clarify the damage mechanism of the subway structure, the dynamic soil-structure interaction and the dynamic forces acting on the structure, a series of shaking table tests and simulation analyses were performed. The seismic response of the structure and the dynamic forces acting on the structure due to sinusoidal and random waves were investigated with special attention to the dynamic soil-structure interaction. The result shows that the compression seismic soil pressures and extension seismic soil pressures simultaneously act on the sidewalls, and big shear stress also acts on the ceiling slab due to horizontal excitation. The seismic soil pressure could be approximated to hyperbola curve, and reached a peak value with increase of the shear strain of the model ground. In addition, a slide and exfoliation phenomenon between the structure and the surrounding ground was simulated, using the nonlinear analyses. The foundation is provided for amending the calculation method of seismic soil pressure and improving the anti-earthquake designing level of underground structure.

  4. COMPUTATIONAL FLUID DYNAMICS RESEARCH ON PRESSURE LOSS OF CROSS-FLOW PERFORATED MUFFLER

    Institute of Scientific and Technical Information of China (English)

    HU Xiaodong; ZHOU Yiqi; FANG Jianhua; MAN Xiliang; ZHAO Zhengxu

    2007-01-01

    The pressure loss of cross-flow perforated muffler has been computed with the procedure of physical modeling, simulation and data processing. Three-dimensional computational fluid dynamics (CFD) has been used to investigate the relations of porosities, flow velocity and diameter of the holes with the pressure loss. Accordingly, some preliminary results have been obtained that pressure loss increases with porosity descent as nearly a hyperbolic trend, rising flow velocity of the input makes the pressure loss increasing with parabola trend, diameter of holes affects little about pressure loss of the muffler. Otherwise, the holes on the perforated pipes make the air flow gently and meanly,which decreases the air impact to the wall and pipes in the muffler. A practical perforated muffler is used to illustrate the available of this method for pressure loss computation, and the comparison shows that the computation results with the method of CFD has reference value for muffler design.

  5. Local Dynamical Instabilities in Magnetized, Radiation Pressure Supported Accretion Disks

    CERN Document Server

    Blaes, Omer M; Blaes, Omer; Socrates, Aristotle

    2000-01-01

    We present a general linear dispersion relation which describes the coupled behavior of magnetorotational, photon bubble, and convective instabilities in weakly magnetized, differentially rotating accretion disks. We presume the accretion disks to be geometrically thin and supported vertically by radiation pressure. We fully incorporate the effects of a nonzero radiative diffusion length on the linear modes. In an equilibrium with purely vertical magnetic field, the vertical magnetorotational modes are completely unaffected by compressibility, stratification, and radiative diffusion. However, in the presence of azimuthal fields, which are expected in differentially rotating flows, the growth rate of all magnetorotational modes can be reduced substantially below the orbital frequency. This occurs if diffusion destroys radiation sound waves on the length scale of the instability, and the magnetic energy density of the azimuthal component exceeds the non-radiative thermal energy density. While sluggish in this c...

  6. High-pressure dynamics of hydrated protein in bioprotective trehalose environment

    Science.gov (United States)

    Diallo, S. O.; Zhang, Q.; O'Neill, H.; Mamontov, E.

    2014-10-01

    We present a pressure-dependence study of the dynamics of lysozyme protein powder immersed in deuterated α ,α -trehalose environment via quasielastic neutron scattering (QENS). The goal is to assess the baroprotective benefits of trehalose on biomolecules by comparing the findings with those of a trehalose-free reference study. While the mean-square displacement of the trehalose-free protein (hydrated to dD2O≃ 40 w%) as a whole, is reduced by increasing pressure, the actual observable relaxation dynamics in the picoseconds to nanoseconds time range remains largely unaffected by pressure—up to the maximum investigated pressure of 2.78(2) Kbar. Our observation is independent of whether or not the protein is mixed with the deuterated sugar. This suggests that the hydrated protein's conformational states at atmospheric pressure remain unaltered by hydrostatic pressures, below 2.78 Kbar. We also found the QENS response to be totally recoverable after ambient pressure conditions are restored. Small-angle neutron diffraction measurements confirm that the protein-protein correlation remains undisturbed. We observe, however, a clear narrowing of the QENS response as the temperature is decreased from 290 to 230 K in both cases, which we parametrize using the Kohlrausch-Williams-Watts stretched exponential model. Only the fraction of protons that are immobile on the accessible time window of the instrument, referred to as the elastic incoherent structure factor, is observably sensitive to pressure, increasing only marginally but systematically with increasing pressure.

  7. Development of a Piezoelectric Polymer Film Pressure Transducer for Low Frequency and Dynamic Pressure Measurement

    Science.gov (United States)

    1990-12-01

    34pyro-", "piezo-" means "to press" in the Greek language and the piezoelectric effect is caused by applying pressure to the material. In 1881, the...LINKING THE BASIC * 180 ’CALL COMMANDS TO THE QUATECH MACHINE LANGUAGE 1 9 0 200 ADC.SETUP=&H3:SETCTM=&H6 210 SETC0=&H9 220 INADC12.B=&HC:SEGADDR...H3CA)+256*PEEK(&H3CB) 270 DEF SEG=CSEG2 280 GOSUB 330 ’QUATECH BOARD SETUP 290 GOSUB 860 ’DATA FILE SETUP 300 GOSUB 1010 ’ AQUIRE DATA 310 320 END 330

  8. Line Emission from Radiation-Pressurized HII Region II: Dynamics and Population Synthesis

    CERN Document Server

    Verdolini, Silvia; Krumholz, Mark R; Matzner, Christopher D; Tielens, Alexander G G M

    2013-01-01

    Optical and infrared emission lines from HII regions are an important diagnostic used to study galaxies, but interpretation of these lines requires significant modeling of both the internal structure and dynamical evolution of the emitting regions. Most of the models in common use today assume that HII region dynamics are dominated by the expansion of stellar wind bubbles, and have neglected the contribution of radiation pressure to the dynamics, and in some cases also to the internal structure. However, recent observations of nearby galaxies suggest that neither assumption is justified, motivating us to revisit the question of how HII region line emission depends on the physics of winds and radiation pressure. In a companion paper we construct models of single HII regions including and excluding radiation pressure and winds, and in this paper we describe a population synthesis code that uses these models to simulate galactic collections of HII regions with varying physical parameters. We show that the choice...

  9. Dynamic pressure model derived from an observation by Sakigake for Comet Halley on 31 December, 1985

    Science.gov (United States)

    Saito, Takao; Yumoto, Kiyohumi; Hirao, Kunio; Saito, Keiji; Nakagawa, Tomoko; Smith, Edward

    1986-01-01

    An outstanding disconnection event (DE)-like knot was observed on 31 Dec. 1985 in P/Halley's tail. Analysis of the Sakigake/IMF data reveals that comet Halley did not encounter the heliospheric neutral sheet on the day, demanding a new explanation of the DE-like event. During this event, the comet encountered a high-speed solar wind from a coronal hole tongue of the Sun. The event can be explained by a dynamic pressure model, according to which the DE-like plasmoid was caused by a sudden increase in the dynamic pressure of the solar wind. A simulation result is found to support this interpretation. The dynamic pressure model for a comet can be compared with the mechanism of a possible geotail disturbance during a spacecraft triggered auroral substorm.

  10. Identification of an average temperature and a dynamical pressure in a multitemperature mixture of fluids.

    Science.gov (United States)

    Gouin, Henri; Ruggeri, Tommaso

    2008-07-01

    We present a classical approach to a mixture of compressible fluids when each constituent has its own temperature. The introduction of an average temperature together with the entropy principle dictates the classical Fick law for diffusion and also novel constitutive equations associated with the difference of temperatures between the components. The constitutive equations fit with results recently obtained through a Maxwellian iteration procedure in extended thermodynamics theory of multitemperature mixtures. The differences of temperatures between the constituents imply the existence of a dynamical pressure even if the fluids have a zero bulk viscosity. The nonequilibrium dynamical pressure can be measured and may be convenient in several physical situations, such as, for example, in cosmological circumstances where--as many authors assert--a dynamical pressure played a major role in the evolution of the early universe.

  11. Experimental research on influence of emulsifier on crystallization quantity of emulsion explosives under dynamic pressure

    Institute of Scientific and Technical Information of China (English)

    HUANG Wen-yao; YAN Shi-long; WU Hong-bo; YUAN Sheng-fang

    2011-01-01

    Dynamic pressure was applied on emulsion explosive by using an underwater explosion measuring apparatus, and the crystallization quantity was measured by dissolution method after emulsion explosive was pressed; the influence of emulsi fier content and type was analyzed. The experimental results show that emulsifier content and type have an important effect on crystallization quantity of emulsion explosive. The crystallization quantity will reduce with Span-80 content from 2% to 4%, so the demulsification and crystallization will decrease if the emulsifier content improves appropriately and the dynamic pressure resistance will increase. For emulsion explosive emulsified by T-152 and Span-80, the crystallization quantity with T-152 is less than that of Span-80 under the same dynamic pressure. This shows that the emulsifying effect of T-152 is better than Span-80.

  12. A data base and analysis program for shuttle main engine dynamic pressure measurements

    Science.gov (United States)

    Coffin, T.

    1986-01-01

    A dynamic pressure data base management system is described for measurements obtained from space shuttle main engine (SSME) hot firing tests. The data were provided in terms of engine power level and rms pressure time histories, and power spectra of the dynamic pressure measurements at selected times during each test. Test measurements and engine locations are defined along with a discussion of data acquisition and reduction procedures. A description of the data base management analysis system is provided and subroutines developed for obtaining selected measurement means, variances, ranges and other statistics of interest are discussed. A summary of pressure spectra obtained at SSME rated power level is provided for reference. Application of the singular value decomposition technique to spectrum interpolation is discussed and isoplots of interpolated spectra are presented to indicate measurement trends with engine power level. Program listings of the data base management and spectrum interpolation software are given. Appendices are included to document all data base measurements.

  13. Application of nonlinear dynamic techniques to high pressure plasma jets

    Science.gov (United States)

    Ghorui, S.; Das, A. K.

    2010-02-01

    Arcs and arc plasmas have been known and used for welding, cutting, chemical synthesis and multitude of other industrial applications for more than hundred years. Though a copious source of heat, light and active species, plasma arc is inherently unstable, turbulent and difficult to control. During recent years, primarily driven by the need of new and energy efficient materials processing, various research groups around the world have been studying new and innovative ways of looking at the issues related to arc dynamics, arc stabilization, species non equilibrium, flow and heat transfer in a stabilized arc plasma device. In this context, experimental determination of nature of arc instabilities using tools of non-linear dynamics, theoretical model formulation, prediction of instability behavior under given operating conditions and possible control methods for the observed instabilities in arcs are reviewed. Space selective probing of the zones inside arc plasma devices without disturbing the system is probably the best way to identify the originating zone of instabilities inside such devices. Existence of extremely high temperature and inaccessibility to direct experimentations due to mechanical obstructions make this task extremely difficult. Probing instabilities in otherwise inaccessible inner regions of the torches, using binary gas mixture as plasma gas is a novel technique that primarily rests on a process known as demixing in arcs. Once a binary gas mixture enters the constricted plasma column, the demixing process sets in causing spatial variations for each of the constituent gases depending on the diffusion coefficients and the gradient of the existing temperature field. By varying concentrations of the constituent gases in the feeding line, it is possible to obtain spatial variations of the plasma composition in a desired manner, enabling spatial probing of the associated zones. Detailed compositional description of different zones inside the torch may be

  14. Dynamic Increase Factors for High Performance Concrete in Compression using Split Hopkinson Pressure Bar

    DEFF Research Database (Denmark)

    Riisgaard, Benjamin; Ngo, Tuan; Mendis, Priyan

    2007-01-01

    This paper provides dynamic increase factors (DIF) in compression for two different High Performance Concretes (HPC), 100 MPa and 160 MPa, respectively. In the experimental investigation 2 different Split Hopkinson Pressure Bars are used in order to test over a wide range of strain rates, 100 sec1...... to 700 sec-1. The results are compared with the CEB Model Code and the Spilt Hopkinson Pressure Bar technique is briefly de-scribed....

  15. Molecular Dynamical Simulation of Water/Ice Phase Transitions within Carbon Nanotubes under Various Pressures

    Institute of Scientific and Technical Information of China (English)

    YIN Bing; DONG Shun-Le

    2009-01-01

    A molecular dynamics simulation is performed for water confined within carbon nanotubes with diameters 11.00 (A) and 12.38 (A).Under pressures from 0.1 MPa to 500MPa the simulations are carried out by cooling from 300K to 240 K.Water molecules tend to transform from disordered to ordered with different configurations (square,pentagonal,hexagonal and hexagonal plus a chain).It is concluded that denser structures may appear under high pressures.

  16. Dynamics of apokamp-type atmospheric pressure plasma jets

    Science.gov (United States)

    Sosnin, Eduard A.; Panarin, Victor A.; Skakun, Victor S.; Baksht, Evgeny Kh.; Tarasenko, Victor F.

    2017-02-01

    The paper describes a new discharge source of atmospheric pressure plasma jets (APPJs) in air with no gas supply through the discharge region. In this discharge mode, plasma jets develop from the bending point of a bright current channel between two electrodes and are therefore termed an apokamp (from Greek `off' and `bend'). The apokamp can represent single plasma jets of length up 6 cm or several jets, and the temperature of such jets can range from more than 1000 °C at their base to 100-250 °C at their tip. Apokamps are formed at maximum applied voltage of positive polarity, provided that the second electrode is capacitively decoupled with ground. According to high-speed photography with time resolution from several nanoseconds to several tens of nanoseconds, the apokamp consists of a set of plasma bullets moving with a velocity of 100-220 km/s, which excludes the convective mechanism of plasma decay. Estimates on a 100-ns scale show that the near-electrode zones and the zones from which apokamps develop are close in temperature.

  17. Dynamic baroreflex control of blood pressure: influence of the heart vs. peripheral resistance.

    Science.gov (United States)

    Liu, Huang-Ku; Guild, Sarah-Jane; Ringwood, John V; Barrett, Carolyn J; Leonard, Bridget L; Nguang, Sing-Kiong; Navakatikyan, Michael A; Malpas, Simon C

    2002-08-01

    The aim in the present experiments was to assess the dynamic baroreflex control of blood pressure, to develop an accurate mathematical model that represented this relationship, and to assess the role of dynamic changes in heart rate and stroke volume in giving rise to components of this response. Patterned electrical stimulation [pseudo-random binary sequence (PRBS)] was applied to the aortic depressor nerve (ADN) to produce changes in blood pressure under open-loop conditions in anesthetized rabbits. The stimulus provided constant power over the frequency range 0-0.5 Hz and revealed that the composite systems represented by the central nervous system, sympathetic activity, and vascular resistance responded as a second-order low-pass filter (corner frequency approximately 0.047 Hz) with a time delay (1.01 s). The gain between ADN and mean arterial pressure was reasonably constant before the corner frequency and then decreased with increasing frequency of stimulus. Although the heart rate was altered in response to the PRBS stimuli, we found that removal of the heart's ability to contribute to blood pressure variability by vagotomy and beta(1)-receptor blockade did not significantly alter the frequency response. We conclude that the contribution of the heart to the dynamic regulation of blood pressure is negligible in the rabbit. The consequences of this finding are examined with respect to low-frequency oscillations in blood pressure.

  18. Dynamic Wave Pressures on Deeply Embedded Large Cylindrical Structures due to Random Waves

    Institute of Scientific and Technical Information of China (English)

    刘海笑; 唐云; 周锡礽

    2003-01-01

    The response of dynamic wave pressures on structures would be more complicated and bring about new phenomena under the dynamic interaction between soil and structure. In order to better understand the response characteristics on deeply embedded large cylindrical structures under random waves, and accordingly to offer valuable findings for engineering, the authors designed wave flume experiments to investigate comparatively dynamic wave pressures on a single and on continuous cylinders with two different embedment depths in response to two wave spectra.The time histories of the water surface elevation and the corresponding dynamic wave pressures exerted on the cylinder were analyzed in the frequency domain. By calculating the transfer function and spectral density for dynamic wave pressures along the height and around the circumference of the cylinder, experimental results of the single cylinder were compared with the theoretical results based on the linear diffraction theory, and detailed comparisons were also carried out between the single and continuous cylinders. Some new findings and the corresponding analysis are reported in present paper. The investigation on continuous cylinders will be used in particular for reference in engineering applications because information is scarce on studying such kind of problem both analytically and experimentally.

  19. Dynamic Shock Compression of Copper to Multi-Megabar Pressure

    Science.gov (United States)

    Haill, T. A.; Furnish, M. D.; Twyeffort, L. L.; Arrington, C. L.; Lemke, R. W.; Knudson, M. D.; Davis, J.-P.

    2015-11-01

    Copper is an important material for a variety of shock and high energy density applications and experiments. Copper is used as a standard reference material to determine the EOS properties of other materials. The high conductivity of copper makes it useful as an MHD driver layer in high current dynamic materials experiments on Sandia National Laboratories Z machine. Composite aluminum/copper flyer plates increase the dwell time in plate impact experiments by taking advantage of the slower wave speeds in copper. This presentation reports on recent efforts to reinstate a composite Al/Cu flyer capability on Z and to extend the range of equation-of-state shock compression data through the use of hyper-velocity composite flyers and symmetric planar impact with copper targets. We will present results from multi-dimensional ALEGRA MHD simulations, as well as experimental designs and methods of composite flyer fabrication. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the U.S. DOE's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  20. Subharmonic contrast microbubble signals for noninvasive pressure estimation under static and dynamic flow conditions.

    Science.gov (United States)

    Halldorsdottir, Valgerdur G; Dave, Jaydev K; Leodore, Lauren M; Eisenbrey, John R; Park, Suhyun; Hall, Anne L; Thomenius, Kai; Forsberg, Flemming

    2011-07-01

    Our group has proposed the concept of subharmonic aided pressure estimation (SHAPE) utilizing microbubble-based ultrasound contrast agent signals for the noninvasive estimation of hydrostatic blood pressures. An experimental system for in vitro SHAPE was constructed based on two single-element transducers assembled confocally at a 60 degree angle to each other. Changes in the first, second and subharmonic amplitudes of five different ultrasound contrast agents were measured in vitro at static hydrostatic pressures from 0-186 mmHg, acoustic pressures from 0.35-0.60 MPa peak-to-peak and frequencies of 2.5-6.6 MHz. The most sensitive agent and optimal parameters for SHAPE were determined using linear regression analysis and implemented on a Logiq 9 scanner (GE Healthcare, Milwaukee, WI). This implementation of SHAPE was then tested under dynamic-flow conditions and compared to pressure-catheter measurements. Over the pressure range studied, the first and second harmonic amplitudes reduced approximately 2 dB for all contrast agents. Over the same pressure range, the subharmonic amplitudes decreased by 9-14 dB and excellent linear regressions were achieved with the hydrostatic pressure variations (r = 0.98, p scanner was modified to implement SHAPE on a convex transducer with a frequency range from 1.5-4.5 MHz and acoustic pressures from 0-3.34 MPa. Results matched the pressure catheter (r2 = 0.87). In conclusion, subharmonic contrast signals are a good indicator of hydrostatic pressure. Out of the five ultrasound contrast agents tested, Sonazoid was the most sensitive for subharmonic pressure estimation. Real-time SHAPE has been implemented on a commercial scanner and offers the possibility of allowing pressures in the heart and elsewhere to be obtained noninvasively.

  1. [Mobile phone platform for wireless monitoring of human dynamic plantar pressure].

    Science.gov (United States)

    Wang, Hao; Han, Meng; Liu, Jing

    2010-11-01

    This paper constructed a plantar pressure sensing system based on Bluetooth communication of mobile phone with embedded Windows Mobile system. With the MCU (Microprocessor Control Unit) and Bluetooth module, the pressure sensor and the data acquisition circuit was designed and integrated, with software developed under Visual Studio 2008 environment. The real-time monitoring of human dynamic plantar pressure signal, and transferring, displaying and storing the recorded data on a mobile phone were achieved. This method offers an important measure to acquire human gait information via a pervasive and low cost way.

  2. Theoretical study on the lattice dynamics and electron-phonon interaction of vanadium under high pressures

    CERN Document Server

    Suzuki, N

    2002-01-01

    First-principles calculations are performed for the lattice dynamics and electron-phonon interaction of the body-centred-cubic (bcc) phase of solid vanadium. A remarkable phonon anomaly is found, i.e. frequencies of the transverse mode around a quarter of the GAMMA-H line show softening with increasing pressure and become imaginary at pressures higher than approx 130 GPa. The superconducting transition temperatures T sub c of bcc vanadium estimated as a function of pressure increases at first linearly with pressure, and then the rate of increase of T sub c is abated around 80 GPa. This calculated pressure dependence of T sub c shows qualitatively the same behaviour as the experimental result.

  3. Dynamic calibration of piezoelectric transducers for ballistic high-pressure measurement

    Directory of Open Access Journals (Sweden)

    Elkarous Lamine

    2016-01-01

    Full Text Available The development of a dynamic calibration standard for high-amplitude pressure piezoelectric transducers implies the implementation of a system which can provide reference pressure values with known characteristics and uncertainty. The reference pressure must be issued by a sensor, as a part of a measuring chain, with a guaranteed traceability to an international standard. However, this operation has not been completely addressed yet until today and is still calling further investigations. In this paper, we introduce an experimental study carried out in order to contribute to current efforts for the establishment of a reference dynamic calibration method. A suitable practical calibration method based on the calculation of the reference pressure by measurement of the displacement of the piston in contact with an oil-filled cylindrical chamber is presented. This measurement was achieved thanks to a high speed camera and an accelerometer. Both measurements are then compared. In the first way, pressure was generated by impacting the piston with a free falling weight and, in the second way, with strikers of known weights and accelerated to the impact velocities with an air gun. The aim of the experimental setup is to work out a system which may generate known hydraulic pressure pulses with high-accuracy and known uncertainty. Moreover, physical models were also introduced to consolidate the experimental study. The change of striker’s velocities and masses allows tuning the reference pressure pulses with different shapes and, therefore, permits to sweep a wide range of magnitudes and frequencies.

  4. Dynamics of phenotypic reversibility of bacterial cells with oscillating hydrostatic pressure

    Science.gov (United States)

    Nepal, Sudip; Kumar, Pradeep

    Bacterial cells encounter and respond to physiochemical fluctuations. The response depends on the extent and type of the stresses applied. The response of bacterial cells to the fluctuating stress is relatively unknown. Here, we have studied the response of wild type Escherichia coli (E. coli) under fluctuating hydrostatic pressures ranging from 1 atm to 500 atm. High pressure acts as a stress to E. coli since these bacteria are adapted to grow optimally at atmospheric pressure. Cell division of E. coli is inhibited at high pressures resulting in increase in the length of the cells. Cell-length is reversible in nature and bacterial cells revert back to normal size on a time scale that is proportional to the strength and time of continuous pressure applied upon relaxing the high pressure condition. We have studied the dynamics of cellular reversibility of E. coli under the conditions in which continuous pressure is applied and subsequently relaxed over different time scales. We have quantified the dynamics of cellular reversibility with different relaxation times. Furthermore, we propose a model to describe the reversibility of the bacterial cell with the relaxation time. Our theoretical model fits well to the experimental data. We further

  5. Lateral Pressure of RC Silos with Static and Dynamic Granular Materials

    Institute of Scientific and Technical Information of China (English)

    Lingkai Meng

    2015-01-01

    This paper aims at analyzing material⁃induced lateral pressure of RC cylinder silo in both static and dynamic condition using the finite element method (FEM).In the finite element software ABAQUS, concrete material is modeled by concrete damaged plasticity model, and stored materials in silo is modeled by the hypoplastic theory.In terms of numerical model, shell elements (S4R) and solid elements (C3D8) are applied for model silo wall and stored materials respectively. The interaction between silo wall and stored materials is simulated by Coulomb friction model and penalty contact constrain provided by ABAQUS.The numerical results are verified with the existing experimental data that are designed to ensure the validation of such numerical model using FEM and it obtains good agreements between numerical results and experimental data. Then the material parameters are analyzed in both static and dynamic condition.According to the analysis, it is clear that critical friction angle, initial void ratio and minimum void ratio have an obvious effect on static lateral pressure while all the material parameters affect dynamic lateral pressure at different levels. In addition, differences of silo wall between elastic and plastic state are analyzed in dynamic condition. The numerical results show that it contributes to increasing dynamic pressure when silo wall enters into the plastic state. Finally, this paper discusses the time⁃history lateral pressure at different heights along silo wall, and analytical results indicate that larger acceleration values play main roles in producing the maximum lateral pressure at higher part of the silo wall.

  6. Evaluation of dynamic fracture toughness for Yong Gwang unit 5 reactor pressure vessel materials (Baseline Tests)

    Energy Technology Data Exchange (ETDEWEB)

    Chi Se Hwan; Kim, Joo Hag; Hong, Jun Hwa; Kwon, Sun Chil; Lee, Bong Sang [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-10-01

    The dynamic fracture toughness (K{sub d}) of intermediate shell and its weld in SA 508 CI. 3 Yong Gwang 5 reactor pressure vessel was determined and evaluated. Precracked thirty six Charpy specimens were tested by using an instrumented impact tester. The purpose of present work is to evaluate and confirm the un-irradiated dynamic fracture toughness and to provide pre-irradiation baseline data for future evaluation on dynamic fracture toughness change during operation. 18 refs., 5 figs., 5 tabs. (Author)

  7. High-resolution dynamic pressure sensor array based on piezo-phototronic effect tuned photoluminescence imaging.

    Science.gov (United States)

    Peng, Mingzeng; Li, Zhou; Liu, Caihong; Zheng, Qiang; Shi, Xieqing; Song, Ming; Zhang, Yang; Du, Shiyu; Zhai, Junyi; Wang, Zhong Lin

    2015-03-24

    A high-resolution dynamic tactile/pressure display is indispensable to the comprehensive perception of force/mechanical stimulations such as electronic skin, biomechanical imaging/analysis, or personalized signatures. Here, we present a dynamic pressure sensor array based on pressure/strain tuned photoluminescence imaging without the need for electricity. Each sensor is a nanopillar that consists of InGaN/GaN multiple quantum wells. Its photoluminescence intensity can be modulated dramatically and linearly by small strain (0-0.15%) owing to the piezo-phototronic effect. The sensor array has a high pixel density of 6350 dpi and exceptional small standard deviation of photoluminescence. High-quality tactile/pressure sensing distribution can be real-time recorded by parallel photoluminescence imaging without any cross-talk. The sensor array can be inexpensively fabricated over large areas by semiconductor product lines. The proposed dynamic all-optical pressure imaging with excellent resolution, high sensitivity, good uniformity, and ultrafast response time offers a suitable way for smart sensing, micro/nano-opto-electromechanical systems.

  8. The Non-selfsimilar Riemann Problem for 2-D Zero-Pressure Flow in Gas Dynamics

    Institute of Scientific and Technical Information of China (English)

    Wenhua SUN; Wancheng SHENG

    2007-01-01

    The non-selfsimilar Riemann problem for two-dimensional zero-pressure flow in gas dynamics with two constant states separated by a convex curve is considered. By means of the generalized Rankine-Hugoniot relation and the generalized characteristic analysis method, the global solution involving delta shock wave and vacuum is constructed. The explicit solution for a special case is also given.

  9. Plasma flow structures as analytical solution of a magneto-hydro-dynamic model with pressure

    Science.gov (United States)

    Paccagnella, R.

    2012-03-01

    In this work starting from a set of magnetohydrodynamic (MHD) equations that describe the dynamical evolution for the pressure driven resistive/interchange modes in a magnetic confinement system, global solutions for the plasma flow relevant for toroidal pinches like tokamaks and reversed field pinches (RFPs) are derived. Analytical solutions for the flow stream function associated with the dominant modes are presented.

  10. Pressure-area isotherm of a lipid monolayer from molecular dynamics simulations

    NARCIS (Netherlands)

    Baoukina, Svetlana; Monticelli, Luca; Marrink, Siewert J.; Tieleman, D. Peter

    2007-01-01

    We calculated the pressure-area isotherm of a dipalmitoyl-phosphatidylcholine (DPPC) lipid monolayer from molecular dynamics simulations using a coarse-grained molecular model. We characterized the monolayer structure, geometry, and phases directly from the simulations and compared the calculated

  11. Towards a standard for the dynamic measurement of pressure based on laser absorption spectroscopy

    Science.gov (United States)

    Douglass, K. O.; Olson, D. A.

    2016-06-01

    We describe an approach for creating a standard for the dynamic measurement of pressure based on the measurement of fundamental quantum properties of molecular systems. From the linewidth and intensities of ro-vibrational transitions we plan on making an accurate determination of pressure and temperature. The goal is to achieve an absolute uncertainty for time-varying pressure of 5% with a measurement rate of 100 kHz, which will in the future serve as a method for the traceable calibration of pressure sensors used in transient processes. To illustrate this concept we have used wavelength modulation spectroscopy (WMS), due to inherent advantages over direct absorption spectroscopy, to perform rapid measurements of carbon dioxide in order to determine the pressure. The system records the full lineshape profile of a single ro-vibrational transition of CO2 at a repetition rate of 4 kHz and with a systematic measurement uncertainty of 12% for the linewidth measurement. A series of pressures were measured at a rate of 400 Hz (10 averages) and from these measurements the linewidth was determined with a relative uncertainty of about 0.5% on average. The pressures measured using WMS have an average difference of 0.6% from the absolute pressure measured with a capacitance diaphragm sensor.

  12. Towards a standard for the dynamic measurement of pressure based on laser absorption spectroscopy.

    Science.gov (United States)

    Douglass, K O; Olson, D A

    2016-06-01

    We describe an approach for creating a standard for the dynamic measurement of pressure based on the measurement of fundamental quantum properties of molecular systems. From the linewidth and intensities of ro-vibrational transitions we plan on making an accurate determination of pressure and temperature. The goal is to achieve an absolute uncertainty for time-varying pressure of 5 % with a measurement rate of 100 kHz, which will in the future serve as a method for the traceable calibration of pressure sensors used in transient processes. To illustrate this concept we have used wavelength modulation spectroscopy (WMS), due to inherent advantages over direct absorption spectroscopy, to perform rapid measurements of carbon dioxide in order to determine the pressure. The system records the full lineshape profile of a single ro-vibrational transition of CO2 at a repetition rate of 4 kHz and with a systematic measurement uncertainty of 12 % for the linewidth measurement. A series of pressures were measured at a rate of 400 Hz (10 averages) and from these measurements the linewidth was determined with a relative uncertainty of about 0.5 % on average. The pressures measured using WMS have an average difference of 0.6 % from the absolute pressure measured with a capacitance diaphragm sensor.

  13. Modeling the dynamic response of pressures in a distributed helium refrigeration system

    Energy Technology Data Exchange (ETDEWEB)

    Brubaker, John Carl [Illinois Inst. of Technology, Chicago, IL (United States)

    1997-12-01

    A mathematical model is created of the dynamic response of pressures caused by flow inputs to an existing distributed helium refrigeration system. The dynamic system studied consists of the suction and discharge pressure headers and compressor portions of the refrigeration system used to cool the superconducting magnets of the Tevatron accelerator at the Fermi National Accelerator Laboratory. The modeling method involves identifying the system from data recorded during a series of controlled tests, with effort made to detect locational differences in pressure response around the four mile accelerator circumference. A review of the fluid mechanics associated with the system indicates linear time invariant models are suitable for the identification, particularly since the governing equations of one dimensional fluid flow are approximated by linear differential equations. An outline of the experimental design and the data acquisition system are given, followed by a detailed description of the modeling, which utilized the Matlab programming language and associated System Identification Toolbox. Two representations of the system are presented. One, a black box model, provides a multi-input, multi-output description assembled from the results of single input step function testing. This description indicates definite variation in pressure response with distance from the flow input location, and also suggests subtle differences in response with the input location itself. A second system representation is proposed which details the relation between continuous flow changes and pressure response, and provides explanation of a previously unappreciated pressure feedback internal to the system.

  14. Dynamic Diamond Anvil Cell (dDAC): A novel device for studying the dynamic-pressure properties of materials

    Energy Technology Data Exchange (ETDEWEB)

    Evans, W J; Yoo, C; Lee, G W; Cynn, H; Lipp, M J; Visbeck, K

    2007-02-23

    We have developed a unique device, a dynamic diamond anvil cell (dDAC), which repetitively applies a time-dependent load/pressure profile to a sample. This capability allows studies of the kinetics of phase transitions and metastable phases at compression (strain) rates of up to 500 GPa/sec ({approx}0.16 s{sup -1} for a metal). Our approach adapts electromechanical piezoelectric actuators to a conventional diamond anvil cell design, which enables precise specification and control of a time-dependent applied load/pressure. Existing DAC instrumentation and experimental techniques are easily adapted to the dDAC to measure the properties of a sample under the varying load/pressure conditions. This capability addresses the sparsely studied regime of dynamic phenomena between static research (diamond anvil cells and large volume presses) and dynamic shock-driven experiments (gas guns, explosive and laser shock). We present an overview of a variety of experimental measurements that can be made with this device.

  15. Modeling of fluid dynamics interacting with ductile fraction propagation in high pressure pipeline

    Institute of Scientific and Technical Information of China (English)

    Mihaela Popescu

    2009-01-01

    This paper presents a computational model for the fluid dynamics in a fractured ductile pipe under high pressure. The pressure profile in front of the crack tip, which is the driving source of crack propagation, is computed using a nonlinear wave equation. The solution is coupled with a one dimensional choked flow analysis behind the crack. The simulation utilizes a high order optimized prefactored com-pact-finite volume method in space, and low dispersion and dissipation Runge-Kutta in time. As the pipe fractures the rapid depressurization take place inside the pipe and the prop-agation of the crack-induced waves strongly influences the outflow dynamics. Consistent with the experimental observa-tion, the model predicts the expansion wave inside the pipe, and the reflection and outflow of the wave. The model also helps characterize the propagation of the crack dynamics and fluid flows around the tip of the crack.

  16. Reappraisal of the intracranial pressure and cerebrospinal fluid dynamics in patients with the so-called "normal pressure hydrocephalus" syndrome.

    Science.gov (United States)

    Sahuquillo, J; Rubio, E; Codina, A; Molins, A; Guitart, J M; Poca, M A; Chasampi, A

    1991-01-01

    Fifty-four shunt-responsive patients were selected from a prospective protocol directed to study patients with suspected normal pressure hydrocephalus (NPH). Patients with gait disturbances, dementia, non-responsive L-Dopa Parkinsonism, urinary or faecal incontinence and an Evans ratio greater or equal to 0.30 on the CT scan were included in the study. As a part of their work-up all patients underwent intracranial pressure monitoring and hydrodynamic studies using Marmarou's bolus test. According to mean intracranial pressure (ICP) and the percentage of high amplitude B-waves, patients were subdivided in the following categories: 1) Active hydrocephalus (mean ICP above 15 mmHg), which is in fact no tone normal pressure hydrocephalus; 2) Compensated unstable hydrocephalus, when mean ICP was below 15 mmHg and B-waves were present in more than 25% of the total recording time and 3) Compensated stable hydrocephalus when ICP was lower or equal to 15 mmHg and beta waves were present in less than 25% of the total recording time. The majority of the patients in this study (70%) presented continuous high or intermittently raised ICP (active or unstable compensated hydrocephalus group). Mean resistance to outflow of CSF (Rout) was 38.8 mm Hg/ml/min in active hydrocephalus and 23.5 mm Hg/ml/min in the compensated group (Students t-test, p less than 0.05). Higher resistance to outflow was found in patients with obliterated cortical sulci and obliterated Sylvian cisterns in the CT scan. No statistically significant correlation was found when plotting the percentage of beta waves against pressure volume index (PVI), compliance or Rout. An exponential correlation was found when plotting beta waves against the sum of conductance to outflow and compliance calculated by PVI method (r = 0.79). Patients with the so-called normal pressure hydrocephalus syndrome have different ICP and CSF dynamic profiles. Additional studies taking into consideration these differences are necessary

  17. HOW SIGNIFICANT IS RADIATION PRESSURE IN THE DYNAMICS OF THE GAS AROUND YOUNG STELLAR CLUSTERS?

    Energy Technology Data Exchange (ETDEWEB)

    Silich, Sergiy; Tenorio-Tagle, Guillermo, E-mail: silich@inaoep.mx [Instituto Nacional de Astrofisica Optica y Electronica, AP 51, 72000 Puebla (Mexico)

    2013-03-01

    The impact of radiation pressure on the dynamics of the gas in the vicinity of young stellar clusters is thoroughly discussed. The radiation over the thermal/ram pressure ratio time evolution is calculated explicitly and the crucial roles of the cluster mechanical power, the strong time evolution of the ionizing photon flux, and the bolometric luminosity of the exciting cluster are stressed. It is shown that radiation has only a narrow window of opportunity to dominate the wind-driven shell dynamics. This may occur only at early stages of the bubble evolution and if the shell expands into a dusty and/or a very dense proto-cluster medium. The impact of radiation pressure on the wind-driven shell always becomes negligible after about 3 Myr. Finally, the wind-driven model results allow one to compare the model predictions with the distribution of thermal pressure derived from X-ray observations. The shape of the thermal pressure profile then allows us to distinguish between the energy and the momentum-dominated regimes of expansion and thus conclude whether radiative losses of energy or the leakage of hot gas from the bubble interior have been significant during bubble evolution.

  18. How Significant is Radiation Pressure in the Dynamics of the Gas Around Young Stellar Clusters?

    CERN Document Server

    Silich, Sergiy

    2013-01-01

    The impact of radiation pressure on the dynamics of the gas in the vicinity of young stellar clusters is thoroughly discussed. The radiation over the thermal/ram pressure ratio time evolution is calculated explicitely and the crucial role of the cluster mechanical power and of the strong time evolution of the ionizing photon flux and of the bolometric luminosity of the exciting cluster is stressed. It is shown that radiation has only a narrow window of opportunity to dominate the wind-driven shell dynamics. This may occur only at early stages of the bubble evolution and if the shell expands into a dusty and/or a very dense proto-cluster medium. The impact of radiation pressure on the wind-driven shell becomes always negligible after about 3 Myr. Finally, the wind-driven model results allow one to compare the model predictions with the distribution of thermal pressure derived from X-ray observations. The shape of the thermal pressure profile allows then to distinguish between the energy and the momentum domina...

  19. Dynamic Acousto-Elasticity: Pressure and Frequency Dependences in Berea Sandstone.

    Science.gov (United States)

    Riviere, J. V.; Pimienta, L.; Latour, S.; Fortin, J.; Schubnel, A.; Johnson, P. A.

    2014-12-01

    Nonlinear elasticity is studied at the laboratory scale with the goal of understanding observations at earth scales, for instance during strong ground motion, tidal forcing and earthquake slip processes. Here we report frequency and pressure dependences on elasticity when applying dynamic acousto-elasticity (DAE) of rock samples, analogous to quasi-static acousto-elasticity. DAE allows one to obtain the elastic behavior over the entire dynamic cycle, detailing the full nonlinear behavior under tension and compression, including hysteresis and memory effects. We perform DAE on a sample of Berea sandstone subject to 0.5MPa uniaxial load, with sinusoidal oscillating strain amplitudes ranging from 10-6 to 10-5 and at frequencies from 0.1 to 260Hz. In addition, the confining pressure is increased stepwise from 0 to 30MPa. We compare results to previous measurements made at lower (mHz) and higher (kHz) frequencies. Nonlinear elastic parameters corresponding to conditioning effects, third order elastic constants and fourth order elastic constants are quantitatively compared over the pressure and frequency ranges. We observe that the decrease in modulus due to conditioning increases with frequency, suggesting a frequency and/or strain-rate dependence that should be included in nonlinear elastic models of rocks. In agreement with previous measurements, nonlinear elastic effects also decrease with confining pressure, suggesting that nonlinear elastic sources such as micro-cracks, soft bonds and dislocations are turned off as the pressure increases.

  20. Novel method for estimating the dynamic characteristics of pressure sensor in shock tube calibration test.

    Science.gov (United States)

    Li, Qiang; Wang, Zhongyu; Wang, Zhuoran; Yan, Hu

    2015-06-01

    A shock tube is usually used to excite the dynamic characteristics of the pressure sensor used in an aircraft. This paper proposes a novel estimation method for determining the dynamic characteristic parameters of the pressure sensor. A preprocessing operation based on Grey Model [GM(1,1)] and bootstrap method (BM) is employed to analyze the output of a calibrated pressure sensor under step excitation. Three sequences, which include the estimated value sequence, upper boundary, and lower boundary, are obtained. The processing methods on filtering and modeling are used to explore the three sequences independently. The optimal estimated, upper boundary, and lower boundary models are then established. The three models are solved, and a group of dynamic characteristic parameters corresponding to the estimated intervals are obtained. A shock tube calibration test consisting of two experiments is performed to validate the performance of the proposed method. The results show that the relative errors of the dynamic characteristic parameters of time and frequency domains do not exceed 9% and 10%, respectively. Moreover, the nominal and estimated values of the parameters fall into the estimated intervals limited by the upper and lower values.

  1. Dynamic distribution of gas pressure and emission around a driving roadway

    Energy Technology Data Exchange (ETDEWEB)

    Gao Jian-liang; Hou San-zhong [Henan Polytechnic University, Jiaozuo (China). School of Safety Science and Engineering

    2007-11-15

    The finite difference method was applied to simulate the dynamic variation of gas pressure in coal seams around a developing roadway and the gas emission rate on the airway surface. The gas pressure distribution advances with the advancement of the working face. The rate of emission of gas from the roadway surface decreases with the elapse of exposure time of the roadway surface. When the new working face is first exposed the emission of methane is highest and it then decreases sharply. 11 refs., 7 figs., 1 tab.

  2. Generation of homogeneous granular packings: Contact dynamics method with coupling to an external pressure bath

    CERN Document Server

    Shaebani, M Reza; Kertesz, Janos

    2008-01-01

    The contact dynamics method (CD) is an efficient simulation technique of dense granular media where unilateral and frictional contact problems for a large number of rigid bodies have to be solved. In this paper we present a modified version of the contact dynamics to generate homogeneous random packings of rigid grains. CD is coupled to an external pressure bath, which allows the variation of the size of a periodically repeated cell. We follow the concept of the Andersen dynamics and show how it can be applied within the framework of the contact dynamics method. The main challenge here is to handle the interparticle interactions properly, which are based on constraint forces in CD. We implement the proposed algorithm, perform test simulations and investigate the properties of the final packings.

  3. Prosthetics socket that incorporates an air splint system focusing on dynamic interface pressure.

    Science.gov (United States)

    Razak, Nasrul Anuar Abd; Osman, Noor Azuan Abu; Gholizadeh, Hossein; Ali, Sadeeq

    2014-08-01

    The interface pressure between the residual limb and prosthetic socket has a significant effect on an amputee's satisfaction and comfort. This paper presents the design and performance of a new prosthetic socket that uses an air splint system. The air splint prosthetic socket system was implemented by combining the air splint with a pressure sensor that the transhumeral user controls through the use of a microcontroller. The modular construction of the system developed allows the FSR pressure sensors that are placed inside the air splint socket to determine the required size and fitting for the socket used. Fifteen transhumeral amputees participated in the study. The subject's dynamic pressure on the socket that's applied while wearing the air splint systems was recorded using F-socket transducers and microcontroller analysis. The values collected by the F-socket sensor for the air splint prosthetic socket system were determined accordingly by comparing the dynamic pressure applied using statically socket. The pressure volume of the air splint fluctuated and was recorded at an average of 38 kPa (2.5) to 41 kPa (1.3) over three hours. The air splint socket might reduce the pressure within the interface of residual limb. This is particularly important during the daily life activities and may reduce the pain and discomfort at the residual limb in comparison to the static socket. The potential development of an auto-adjusted socket that uses an air splint system as the prosthetic socket will be of interest to researchers involved in rehabilitation engineering, prosthetics and orthotics.

  4. Parallel molecular dynamics simulations of pressure-induced structural transformations in cadmium selenide nanocrystals

    Science.gov (United States)

    Lee, Nicholas Jabari Ouma

    Parallel molecular dynamics (MD) simulations are performed to investigate pressure-induced solid-to-solid structural phase transformations in cadmium selenide (CdSe) nanorods. The effects of the size and shape of nanorods on different aspects of structural phase transformations are studied. Simulations are based on interatomic potentials validated extensively by experiments. Simulations range from 105 to 106 atoms. These simulations are enabled by highly scalable algorithms executed on massively parallel Beowulf computing architectures. Pressure-induced structural transformations are studied using a hydrostatic pressure medium simulated by atoms interacting via Lennard-Jones potential. Four single-crystal CdSe nanorods, each 44A in diameter but varying in length, in the range between 44A and 600A, are studied independently in two sets of simulations. The first simulation is the downstroke simulation, where each rod is embedded in the pressure medium and subjected to increasing pressure during which it undergoes a forward transformation from a 4-fold coordinated wurtzite (WZ) crystal structure to a 6-fold coordinated rocksalt (RS) crystal structure. In the second so-called upstroke simulation, the pressure on the rods is decreased and a reverse transformation from 6-fold RS to a 4-fold coordinated phase is observed. The transformation pressure in the forward transformation depends on the nanorod size, with longer rods transforming at lower pressures close to the bulk transformation pressure. Spatially-resolved structural analyses, including pair-distributions, atomic-coordinations and bond-angle distributions, indicate nucleation begins at the surface of nanorods and spreads inward. The transformation results in a single RS domain, in agreement with experiments. The microscopic mechanism for transformation is observed to be the same as for bulk CdSe. A nanorod size dependency is also found in reverse structural transformations, with longer nanorods transforming more

  5. Pressure-dependent morphology of trihexyl(tetradecyl)phosphonium ionic liquids: A molecular dynamics study

    Science.gov (United States)

    Sharma, Shobha; Gupta, Aditya; Dhabal, Debdas; Kashyap, Hemant K.

    2016-10-01

    In the present molecular dynamics study, we investigate the effects of increasing pressure on the structural morphology of trihexyl(tetradecyl)phosphonium bromide (P666,14+/Br-) and trihexyl(tetradecyl)phosphonium dicyanamide (P666,14+/DCA-) ionic liquids (ILs). Special attention was paid to how charge and polarity orderings, which are present in the microscopic structure of these ILs at ambient conditions, respond to very high external pressure. The simulated X-ray scattering structure functions, S(q)s, of the two systems reveal that both the characteristic orderings show appreciable responsiveness towards the applied pressure change. At a given pressure, a slight difference between the polarity ordering (PO), charge ordering (CO), and adjacency correlations (AC) for both the systems points towards different microscopic structure of the two ILs due to change in anion. Beyond a certain pressure, we observe emergence of a new low-q peak in the S(q)s of both the systems. The new peak is associated with formation of crystalline order in these systems at higher pressures and the real space length-scale corresponding to the crystalline order lies in between those of polarity- and charge-ordering. Beyond the transition pressure, the crystallinity of both the systems increases with increasing pressure and the corresponding length-scale shifts towards smaller values upon increasing pressure. We also observe that the extent of the usual polarity ordering decreases upon increasing pressure for both the P666,14+/Br- and P666,14+/DCA- systems. We demonstrate that the disappearance of the usual polarity peak is due to decreased polar-polar and apolar-apolar correlations and enhanced correlations between the charged and uncharged groups of the ions. This scenario is completely reversed for the components corresponding to the crystalline order, the polar-polar and apolar-apolar correlations are enhanced and polar-apolar correlations are diminished at higher pressure. In addition

  6. Dynamic compressive properties obtained from a split Hopkinson pressure bar test of Boryeong shale

    Science.gov (United States)

    Kang, Minju; Cho, Jung-Woo; Kim, Yang Gon; Park, Jaeyeong; Jeong, Myeong-Sik; Lee, Sunghak

    2016-09-01

    Dynamic compressive properties of a Boryeong shale were evaluated by using a split Hopkinson pressure bar, and were compared with those of a Hwangdeung granite which is a typical hard rock. The results indicated that the dynamic compressive loading reduced the resistance to fracture. The dynamic compressive strength was lower in the shale than in the granite, and was raised with increasing strain rate by microcracking effect as well as strain rate strengthening effect. Since the number of microcracked fragments increased with increasing strain rate in the shale having laminated weakness planes, the shale showed the better fragmentation performance than the granite at high strain rates. The effect of transversely isotropic plane on compressive strength decreased with increasing strain rate, which was desirable for increasing the fragmentation performance. Thus, the shale can be more reliably applied to industrial areas requiring good fragmentation performance as the striking speed of drilling or hydraulic fracturing machines increased. The present dynamic compressive test effectively evaluated the fragmentation performance as well as compressive strength and strain energy density by controlling the air pressure, and provided an important idea on which rock was more readily fragmented under dynamically processing conditions such as high-speed drilling and blasting.

  7. Study of dynamic pressure roadway supporting scheme under condition of thick composite roof

    Institute of Scientific and Technical Information of China (English)

    Wei-Jun WANG; Li-Qiang LUO; Wei-Jian YU; Hai WU; Yan-Si QU

    2013-01-01

    This paper analyzed the strata behaviors of solid-coal roadway,gob-side entry driving and deformation law of surrounding rock in depth under high stress and thick composite roof based on the dynamic pressure roadway as engineering background in Fengcheng mining area,Jiangxi province.The results,both field measurement andnumerical simulation show that gob-side entry driving results the deformation of coal roadway main wall,however,entity-coal roadway driving results deformation of main roof and floor.The maintenance state of gob-side entry driving is better than entity-coal roadway,this situation is relevant to thick composite roof layered and easy collapse characteristics.At the same time,this paper put forward and proved proper dynamic pressure roadway supporting scheme under the surrounding rock condition and stress environment.

  8. Bifurcation and Nonlinear Dynamic Analysis of Externally Pressurized Double Air Films Bearing System

    Directory of Open Access Journals (Sweden)

    Cheng-Chi Wang

    2014-01-01

    Full Text Available This paper studies the chaotic and nonlinear dynamic behaviors of a rigid rotor supported by externally pressurized double air films (EPDAF bearing system. A hybrid numerical method combining the differential transformation method and the finite difference method is used to calculate pressure distribution of EPDAF bearing system and bifurcation phenomenon of rotor center orbits. The results obtained for the orbits of the rotor center are in good agreement with those obtained using the traditional finite difference approach. The results presented summarize the changes which take place in the dynamic behavior of the EPDAF bearing system as the rotor mass and bearing number are increased and therefore provide a useful guideline for the bearing system.

  9. Molecular dynamics study for the melting curve of MgO at high pressure

    Institute of Scientific and Technical Information of China (English)

    Liu Zi-Jiang; Cheng Xin-Lu; Zhang Hong; Cai Ling-Cang

    2004-01-01

    Shell-model molecular dynamics method is used to study the melting temperatures of MgO at elevated temperatures and high pressures using interaction potentials. Equations of state for MgO simulated by molecular dynamics are in good agreement with available experimental data. The pressure dependence of the melting curve of MgO has been calculated. The surface melting and superheating are considered in the correction of experimental data and the calculated values, respectively. The results of corrections are compared with those of previous work. The corrected melting temperature of MgO is consistent with corrected experimental measurements. The melting temperature of MgO up to 140GPa is calculated.

  10. DYNAMIC CHARACTERISTICS OF ELECTRO-HYDRAULIC PROPORTIONAL PRESSURE-FLOW HYBRID VALVE

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The structure principles under the flow and pressure working conditions are studied, in order to investigate the dynamic characteristics of the electro-hydraulic proportional pressure-flow hybrid valve. According to the structure principles under the two different working conditions, the transfer functions under such conditions are derived. With the transfer functions, some structure elements that may affect its performance, are investigated, afterwards some principles of optimality and effective methods for improving the dynamic performance of the valve are proposed. The conclusions can be used to instruct engineering applications and products designing. The test results conform to the results of the theoretical analysis and simulation, which proves the correctness of the study and simulation works.

  11. Dynamic characteristics of bubbling fluidization through recurrence rate analysis of pressure fluctuations

    Institute of Scientific and Technical Information of China (English)

    Hossein Sedighikamal; Reza Zarghami

    2013-01-01

    Pressure fluctuations signals of a lab-scale fluidized bed (15 cm inner diameter and 2 m height) at different superficial gas velocities were measured.Recurrence plot (RP) and recurrence rate (RR),and the simplest variable of recurrence quantification analysis (RQA) were used to analyze the pressure signals.Different patterns observed in RP reflect different dynamic behavior of the system under study.It was also found that the variance of RR (σ2RR) could reveal the peak dominant frequencies (PDF) of different dynamic systems:completely periodic,completely stochastic,Lorenz system,and fluidized bed.The results were compared with power spectral density.Additionally,the diagram of σ2RR provides a new technique for prediction of transition velocity from bubbling to turbulent fluidization regime.

  12. Review of roadway control in soft surrounding rock under dynamic pressure

    Institute of Scientific and Technical Information of China (English)

    侯朝炯

    2003-01-01

    The basic characteristics of the soft rock roadway under the dynamic pressure are analyzed. At the same time, the three fundamental approaches for controlling the surrounding rock are proposed, which are improving the surrounding rock strength, lowering the rock mass stress and selecting the reasonable supporting technology. The research results are elucidated, including the distribution of the surrounding rock plastic zone, the movement and damage of the surrounding rock under the dynamic pressure, controlling the floor heave through reinforcing the roadway walls and corners, the new route to develop the roadway metal supporting technique, the key theory and technique for the bolt supporting in the coal roadway, the performance and prospect of the ZKD high-water-content quick-setting material, and so on. Finally, some personally views are put forward about the roadway metal supporting, bolt supporting, new material and the stress-relief under the high stress condition.

  13. Interplay between lattice dynamics and the low-pressure phase of simple cubic polonium

    Science.gov (United States)

    Zaoui, A.; Belabbes, A.; Ahuja, R.; Ferhat, M.

    2011-04-01

    Low-pressure structural properties of simple cubic polonium are explored through first-principles density-functional theory based relativistic total energy calculations using pseudopotentials and plane-wave basis set, as well as linear-response theory. We have found that Po undergoes structural phase transition at low pressure near 2 GPa, where the element transforms from simple cubic to a mixture of two trigonal phases namely, hR1 (α=86°) and hR2 (α=97.9°) structures. The lattice dynamics calculations provide strong support for the observed phase transition, and show the dynamical stability (instability) of the hR2 (hR1) phase.

  14. Regime change thresholds in flute-like instruments: influence of the mouth pressure dynamics

    CERN Document Server

    Terrien, Soizic; Vergez, Christophe; Fabre, Benoît

    2014-01-01

    Since they correspond to a jump from a given note to another one, the mouth pressure thresholds leading to regime changes are particularly important quantities in flute-like instruments. In this paper, a comparison of such thresholds between an artificial mouth, an experienced flutist and a non player is provided. It highlights the ability of the experienced player to considerabily shift regime change thresholds, and thus to enlarge its control in terms of nuances and spectrum. Based on recent works on other wind instruments and on the theory of dynamic bifurcations, the hypothe- sis is tested experimentally and numerically that the dynamics of the blowing pressure influences regime change thresholds. The results highlight the strong influence of this parameter on thresholds, suggesting its wide use by experienced musicians. Starting from these observations and from an analysis of a physical model of flute-like instruments, involving numerical continuation methods and Floquet stability analysis, a phenomenolo...

  15. A total pressure-saturation formulation of two-phase flow incorporating dynamic effects in the capillary-pressure-saturation relationship

    Energy Technology Data Exchange (ETDEWEB)

    Dahle, H.K.; Celia, M.A.; Hassanizadeh, S.M.; Karlsen, K.H.

    2002-07-01

    New theories suggest that the relationship between capillary pressure and saturation should be enhanced by a dynamic term that is proportional to the time rate of change of saturation. This so-called dynamic capillary pressure formulation is supported by laboratory experiments, and can be included in various forms of the governing equations for two-phase flow in porous media. An extended model of two-phase flow in porous media may be developed based on fractional flow curves and a total pressure - saturation description that includes the dynamic capillary pressure terms. A dimensionless form of the resulting equation set provides an ideal tool to study the relative importance of the dynamic capillary pressure effect. This equation provides a rich set of mathematical research questions, and numerical solutions to the equation provide insights into the behavior of two-phase immiscible flow. For typical two-phase flow systems, dynamic capillary pressure acts to retard infiltration fronts, with responses dependent on system parameters including boundary conditions. Recent theoretical work suggests that the traditional algebraic relationship between capillary pressure and saturation may be inadequate. Instead, a so-called dynamic capillary pressure formulation is needed, where capillary pressure is defined as a thermodynamic variable, and the difference between phase pressures is only equal to the capillary pressure at equilibrium. Under dynamic conditions, the disequilibrium between phase-pressure differences and the capillary pressure is taken to be proportional to the time rate of change of saturation. A recent study by Hassanizadeh et al. presents experimental evidence, culled from the literature, to support this claim. Numerical simulations using dynamic pore-scale network models and upscaling also support the claim. Hassanizadeh et al. also presented numerical solutions for an enhanced version of Richards' equation that included the dynamic terms. A

  16. Nonlinear systems dynamics in cardiovascular physiology: The heart rate delay map and lower body negative pressure

    Science.gov (United States)

    Hooker, John C.

    1990-01-01

    A preliminary study of the applicability of nonlinear dynamic systems analysis techniques to low body negative pressure (LBNP) studies. In particular, the applicability of the heart rate delay map is investigated. It is suggested that the heart rate delay map has potential as a supplemental tool in the assessment of subject performance in LBNP tests and possibly in the determination of susceptibility to cardiovascular deconditioning with spaceflight.

  17. Riemann problem for the zero-pressure flow in gas dynamics

    Institute of Scientific and Technical Information of China (English)

    李杰权; 荔炜

    2001-01-01

    The Riemann problem for zero-pressure flow in gas dynamics in one dimension and two dimensions is investigated. Through studying the generalized Rankine-Hugoniot conditions of delta-shock waves, the one-dimensional Riemann solution is proposed which exhibits four different structures when the initial density involves Dirac measure. For the two-dimensional case, the Riemann solution with two pieces of initial constant states separated at a smooth curve is obtained.

  18. Interactions of Delta Shock Waves for Zero-Pressure Gas Dynamics with Energy Conservation Law

    Directory of Open Access Journals (Sweden)

    Wei Cai

    2016-01-01

    Full Text Available We study the interactions of delta shock waves and vacuum states for the system of conservation laws of mass, momentum, and energy in zero-pressure gas dynamics. The Riemann problems with initial data of three piecewise constant states are solved case by case, and four different configurations of Riemann solutions are constructed. Furthermore, the numerical simulations completely coinciding with theoretical analysis are shown.

  19. SOME EXACT SOLUTIONS OF 3-DIMENSIONAL ZERO-PRESSURE GAS DYNAMICS SYSTEM

    Institute of Scientific and Technical Information of China (English)

    K.T.Joseph; Manas R. Sahoo

    2011-01-01

    The 3-dimensional zero-pressure gas dynamics system appears in the modeling for the large scale structure formation in the universe.The aim of this paper is to construct spherically symmetric solutions to the system.The radial component of the velocity and density satisfy a simpler one dimensional problem.First we construct explicit solutions of this one dimensional case with initial and boundary conditions.Then we get special radial solutions with different behaviours at the origin.

  20. Muscle tissue oxygenation, pressure, electrical, and mechanical responses during dynamic and static voluntary contractions

    DEFF Research Database (Denmark)

    Vedsted, Pernille; Blangsted, Anne Katrine; Søgaard, Karen

    2006-01-01

    Dynamic muscle contractions have been shown to cause greater energy turnover and fatigue than static contractions performed at a corresponding force level. Therefore, we hypothesized that: (1) electro- (EMG) and mechanomyography (MMG), intramuscular pressure (IMP), and reduction in muscle oxygen...... similar in spite of major differences in the MMG and EMG responses of the muscle during contraction periods. This may relate to the surprisingly lower IMP in DYN than IST....

  1. Local order evolution of liquid Cu during glass transition under different pressures: A molecular dynamics study

    Energy Technology Data Exchange (ETDEWEB)

    Li, Y.D., E-mail: ydli@ustc.edu [School of Physics and Material Science, Anhui University, Hefei 230039 (China); Lu, Q.L. [School of Physics and Material Science, Anhui University, Hefei 230039 (China); Wang, C.C., E-mail: ccwang@ahu.edu.cn [School of Physics and Material Science, Anhui University, Hefei 230039 (China); Huang, S.G. [School of Physics and Material Science, Anhui University, Hefei 230039 (China); Liu, C.S. [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China)

    2013-01-01

    Based on the second-moment approximation of tight-binding scheme, constant-pressure molecular dynamics simulations are performed for liquid Cu during the glass transition under different pressures. By means of pair analysis technique and bond orientational order analysis we find that the dominant bond pairs are those related to fcc and hcp crystalline order not those representing icosahedral short-range order (ISRO) when the systems enter into glass transition region. Although these two kinds of bond pairs compete with each other, the system tends towards a mixture of crystalline bond pairs during glass formation. The effect on various bond pairs brought about by higher pressure is much less for liquids than for glasses. The experimental observation of a shoulder on the second peak of the structure factor for supercooled liquids might not merely attribute to ISRO, since supercooled liquid Cu exhibits such a shoulder, but does not display an enhanced icosahedral symmetry.

  2. Molecular dynamics simulations of water on a hydrophilic silica surface at high air pressures

    DEFF Research Database (Denmark)

    Zambrano, H.A.; Walther, Jens Honore; Jaffe, R.L.

    2014-01-01

    of air in water at different pressures. Using the calibrated force field, we conduct MD simulations to study the interface between a hydrophilic silica substrate and water surrounded by air at different pressures. We find that the static water contact angle is independent of the air pressure imposed......Wepresent a force field forMolecular Dynamics (MD) simulations ofwater and air in contactwith an amorphous silica surface. We calibrate the interactions of each species present in the systemusing dedicated criteria such as the contact angle of a water droplet on a silica surface, and the solubility...... on the system. Our simulations reveal the presence of a nanometer thick layer of gas at the water–silica interface. We believe that this gas layer could promote nucleation and stabilization of surface nanobubbles at amorphous silica surfaces. © 2014 Elsevier B.V. All rights reserved....

  3. Air Entrainment in Dynamic Wetting: Knudsen Effects and the Influence of Ambient Air Pressure

    CERN Document Server

    Sprittles, James E

    2015-01-01

    Recent experiments on coating flows and liquid drop impact both demonstrate that wetting failures caused by air entrainment can be suppressed by reducing the ambient gas pressure. Here, it is shown that non-equilibrium effects in the gas can account for this behaviour, with ambient pressure reductions increasing the gas' mean free path and hence the Knudsen number $Kn$. These effects first manifest themselves through Maxwell slip at the gas' boundaries so that for sufficiently small $Kn$ they can be incorporated into a continuum model for dynamic wetting flows. The resulting mathematical model contains flow structures on the nano-, micro- and milli-metre scales and is implemented into a computational platform developed specifically for such multiscale phenomena. The coating flow geometry is used to show that for a fixed gas-liquid-solid system (a) the increased Maxwell slip at reduced pressures can substantially delay air entrainment, i.e. increase the `maximum speed of wetting', (b) unbounded maximum speeds ...

  4. Theory for planetary exospheres: I. Radiation pressure effect on dynamical trajectories

    CERN Document Server

    Beth, Arnaud; Toublanc, Dominique; Dandouras, Iannis; Mazelle, Christian

    2015-01-01

    The planetary exospheres are poorly known in their outer parts, since the neutral densities are low compared with the instruments detection capabilities. The exospheric models are thus often the main source of information at such high altitudes. We present a new way to take into account analytically the additional effect of the radiation pressure on planetary exospheres. In a series of papers, we present with an Hamiltonian approach the effect of the radiation pressure on dynamical trajectories, density profiles and escaping thermal flux. Our work is a generalization of the study by Bishop and Chamberlain (1989). In this first paper, we present the complete exact solutions of particles trajectories, which are not conics, under the influence of the solar radiation pressure. This problem was recently partly solved by Lantoine and Russell (2011) and Biscani and Izzo (2014). We give here the full set of solutions, including solutions not previously derived, as well as simpler formulations for previously known cas...

  5. The dynamic properties of shock-waves formed during laser ablation at sub-atmospheric pressures

    Science.gov (United States)

    Kapitan, D.; Coutts, D. W.

    2002-01-01

    The Sedov-Taylor-von Neumann (STN) theory has been shown to accurately describe the dynamic properties of shock-waves generated during pulsed-laser ablation of solid aluminium targets at visible wavelengths (510/578 nm) with 40 ns pulses with energies up to 3.5 mJ. A ballistic pendulum is used to measure the integrated recoil pressure in various inert atmospheres (He, Ne, Ar, Kr, Xe, N2, CO2, SF6) with pressures of 10-2 - 103 mbar. This recoil momentum is found to scale linearly with the background gas pressure P1 and with the square root of the molecular weight M1. More interestingly, the scaling with the ratio of heat capacities γ is verified to be a monotonically increasing function dependent on the form factor of the shock-wave. The validity of a modified STN theory which accounts for the piston mass is assessed.

  6. A new cable truss support system for coal roadways affected by dynamic pressure

    Institute of Scientific and Technical Information of China (English)

    Hong Yan; Fulian He

    2012-01-01

    The support of coal roadways is seriously affected by intense dynamic pressures.This can lead to problems with large deformation of the roof and the two side walls of coal roadways.Rapid convergence of the walls and roof,a high damage rate to the bolts and cables,or even abrupt roof collapse or rib spalling can occur during the service period of these coal roadways.Analyzing the main support measures used in China leads to a proposed new cable truss supporting system.Thorough study of the entire structure shows the superiority of this design for roadways suffering under dynamic pressure.A corresponding mechanical model of the rock surrounding the cable truss system is described in this paper and formulas for calculating pre-tightening forces of the truss cable,and the minimum anchoring forces,were deduced.The new support system was applied to a typical roadway affected by intensive dynamic pressure that is located in the Xinyuan Coal Mine.The results show that the largest subsidence of the roof was 97 mm,the convergence of the two sides was less than 248 mm,and the average depth of the loose,fractured layer was only 6.12 mm.This proves that the new support system is feasible and effective.

  7. [Validation of the Tekscan system for statistic and dynamic pressure measurements of the human femorotibial joint].

    Science.gov (United States)

    Wirz, D; Becker, R; Li, S Feng; Friederich, N F; Müller, W

    2002-01-01

    In vitro dynamic pressure measurements in the healthy and pathologically altered knee joint help to improve our understanding of the loading pattern on femorotibial surfaces. The aim of the study was to evaluate a piezoresistive pressure measuring system. A human cadaveric knee was mounted in a material-testing machine (Bionix 858) using a specially designed knee-holding device. Axial loading of the knee, flexed at 20o, at 500 N, 1000N and 1500 N was then carried out. For the static investigations, the piezoresistive measuring system (Tekscan), was compared with the FUJI measuring system. In addition, dynamic measurements were also performed with the Tekscan System. With the exception of the lateral compartment at a load of 1500 N, no differences in maximum pressures were observed between the two systems. Nor were there any differences with regard to contact surfaces, either in the medial or lateral compartment (p > 0.05). However, the reproducibility of the data was significantly higher with the Tekscan System (p Tekscan System proved to be more reliable than the FUJI System, and permits simultaneous measurements in both compartments. The Tekscan System is suitable for dynamic measurement of the femorotibial joint, and permits measurements to be made under more physiological conditions.

  8. Dynamics of liquid helium boil-off experiments with a step change in pressure

    Science.gov (United States)

    Cha, Y. S.; Niemann, R. C.; Hull, J. R.

    The results of dynamic analysis of the effect of pressure variations during helium boil-off experiments are presented. A general solution of the diffusion equation with a time-dependent boundary condition is employed to describe the dynamic response of the liquid helium system under variable pressure conditions, and a solution is obtained for the special case when the system is subjected to a step change in pressure. The calculated temperature response of the liquid indicates that most of the experiments were not likely to have reached equilibrium as a result of the low thermal diffusivity of liquid helium. The initial rate of evaporation or condensation is large, and the rate decreases sharply with time. A method is proposed to account for the transient effect that is observed during calculation of the heat loss rate from a helium boil-off experiment. By assuming that there is no mixing at all, the present analysis provides an estimate of the upper (condensation) or lower (evaporation) bound of the heat loss rate as a result of a pressure increase or decrease in the system. A previously reported equilibrium analysis is expected to apply to situations where complete mixing occurred in the bulk liquid and provides the opposite limits.

  9. High hydrostatic pressure specifically affects molecular dynamics and shape of low-density lipoprotein particles

    Science.gov (United States)

    Golub, M.; Lehofer, B.; Martinez, N.; Ollivier, J.; Kohlbrecher, J.; Prassl, R.; Peters, J.

    2017-04-01

    Lipid composition of human low-density lipoprotein (LDL) and its physicochemical characteristics are relevant for proper functioning of lipid transport in the blood circulation. To explore dynamical and structural features of LDL particles with either a normal or a triglyceride-rich lipid composition we combined coherent and incoherent neutron scattering methods. The investigations were carried out under high hydrostatic pressure (HHP), which is a versatile tool to study the physicochemical behavior of biomolecules in solution at a molecular level. Within both neutron techniques we applied HHP to probe the shape and degree of freedom of the possible motions (within the time windows of 15 and 100 ps) and consequently the flexibility of LDL particles. We found that HHP does not change the types of motion in LDL, but influences the portion of motions participating. Contrary to our assumption that lipoprotein particles, like membranes, are highly sensitive to pressure we determined that LDL copes surprisingly well with high pressure conditions, although the lipid composition, particularly the triglyceride content of the particles, impacts the molecular dynamics and shape arrangement of LDL under pressure.

  10. Dynamic Response of High-Pressure Riser of Deepwater SBOP System

    Directory of Open Access Journals (Sweden)

    Kanhua Su

    2012-08-01

    Full Text Available The application of surface blowout preventer (SBOP drilling system in deepwater environments has been demonstrated that it can save operation cost and time. The high pressure small diameter casing plays the role of the conventional riser and bears the complex loading caused by the wave and current force and drilling platform motion. The coupled quasi-static and uncoupled dynamic analysis models of deepwater SBOP drilling system were established. The analysis results indicate that the uncoupled method without consider the lateral offset on the end of the high pressure riser nearly no affection to the riser analysis. However, the uncoupled method has a certain impact on the mechanical analysis of the subsea wellhead and the casing string under mudline. The lateral offset of the high pressure riser changes greatly in the different times, the bending moment of the upper and lower stress joint of riser is bigger. The platform long-term drift has a greater impact on the dynamic response analysis of the high pressure riser of SBOP system for deepwater drilling.

  11. Chaotic dynamic characteristics of pressure fluctuation signals in hydro-turbine

    Energy Technology Data Exchange (ETDEWEB)

    Su, Wen Tao; An, Shi [School of Management, Harbin Institute of Technology, Harbin (China); Li, Xiao Bin; Lan, Chao Feng; Li, Feng Chen [School of Energy Science and Engineering, Harbin Institute of Technology, Harbin (China); Wang, Jian Sheng [Ministry of Education of China, Tianjin (China)

    2016-11-15

    The pressure fluctuation characteristics in a Francis hydro-turbine running at partial flow conditions were studied based on the chaotic dynamic methods. Firstly, the experimental data of pressure fluctuations in the draft tube at various flow conditions was de-noised using lifting wavelet transformation, then, for the de-noised signals, their spectrum distribution on the frequency domain, the energy variation and the energy partition accounting for the total energy was calculated. Hereby, for the flow conditions ranging from no cavitation to severe cavitation, the chaos dynamic features of fluctuation signals were analyzed, including the temporal-frequency distribution, phase trajectory, Lyapunov exponent and Poincaré map etc. It is revealed that, the main energy of pressure fluctuations in the draft tube locates at low-frequency region. As the cavitation grows, the amplitude of power spectrum at frequency domain becomes larger. For all the flow conditions, all the maximal Lyapunov exponents are larger than zero, and they increase with the cavitation level. Therefore, it is believed that there indeed exist the chaotic attractors in the pressure fluctuation signals for a hydro-turbine.

  12. Dynamic stabilization of cubic CaSiO3 perovskite at high temperatures and pressures from ab initio molecular dynamics

    Science.gov (United States)

    Sun, Tao; Zhang, Dong-Bo; Wentzcovitch, Renata M.

    2014-03-01

    The stability of cubic CaSiO3 perovskite (CaPv) at high temperatures and pressures is investigated by vibrational normal-mode analysis. We compute power spectra of mode autocorrelation functions using a recently developed hybrid approach combining ab initio molecular dynamics with lattice dynamics. These power spectra, together with the probability distributions of atomic displacements, indicate that cubic CaPv is stabilized at T ˜600 K and P ˜ 26 GPa. We then utilize the concept of phonon quasiparticles to characterize the vibrational properties of cubic CaPv at high temperature and obtain anharmonic phonon dispersions through the whole Brillouin zone. Such temperature-dependent phonon dispersions pave the way for more accurate calculations of free-energy, thermodynamic, and thermoelastic properties of cubic CaPv at Earth's lower mantle conditions.

  13. Dynamic High Pressure Study of Chemistry and Physics of Molecular Materials

    Science.gov (United States)

    Jezowski, Sebastian Ryszard

    Both temperature and pressure control and influence the packing of molecules in crystalline phases. Our molecular simulations indicate that at ambient pressure, the cubic polymorph of tetracyanoethylene, TCNE, is the energetically stable form up to ˜ 160 K. The observed transition from the cubic to the monoclinic polymorph occurs however only at temperatures above ˜ 318 K due to the large transition barrier. The temperature-induced phase transition in TCNE studied with high-resolution IR spectroscopy is explained in terms of the increased vibrational entropy in the crystals of the monoclinic polymorph. Based upon the inverted design of the Merril-Bassett Diamond Anvil Cell, an improved, second generation dynamic Diamond Anvil Cell was developed. Based on the fluorescence of ruby crystals, we were able to demonstrate that the pressure variation range can be further increased at least up to 7 kbar and that the dynamic pressure compression of up to 1400 GPa/s can be achieved. A new class of mechanophoric system, bis-anthracene, BA, and its photoisomer, PI, is shown to respond reversibly to a mild, static pressure induced by a Diamond Anvil Cell as well as to shear deformation based on absorption spectroscopic measurements. The forward reaction occurs upon illumination with light while the back-reaction may be accelerated upon heating or mechanical stress, coupled to a rehybridization on four equivalent carbon atoms. It is an intriguing result as high pressure stabilizes the photodimerized species in related systems. Our molecular volume simulations ruled out significant differences in the volumes between bis-anthracene and its photoisomer. Kinetic absorption measurements at several different pressures reveal a negative volume of activation in the exothermic back-reaction at room temperature. Through a series of temperature-dependent kinetic measurements it is shown that the barrier of activation for the back-reaction is reduced by more than an order of magnitude at

  14. Experimental Study of Pore Pressure and Deformation of Suction Bucket Foundations Under Horizontal Dynamic Loading

    Institute of Scientific and Technical Information of China (English)

    LU Xiao-bing; WANG Shu-yun; ZHANG Jian-hong; SUN Guo-liang; SHI Zhong-min

    2005-01-01

    Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index (excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index) decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket′s side wall in the horizontal direction. Large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height (when the diameter is the same) are heavier. A cyclic crack some distance near the bucket occurs in the sand.

  15. Electron dynamics and plasma jet formation in a helium atmospheric pressure dielectric barrier discharge jet

    Energy Technology Data Exchange (ETDEWEB)

    Algwari, Q. Th. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); Electronic Department, College of Electronics Engineering, Mosul University, Mosul 41002 (Iraq); O' Connell, D. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); York Plasma Institute, Department of Physics, University of York, York YO10 5DD (United Kingdom)

    2011-09-19

    The excitation dynamics within the main plasma production region and the plasma jets of a kHz atmospheric pressure dielectric barrier discharge (DBD) jet operated in helium was investigated. Within the dielectric tube, the plasma ignites as a streamer-type discharge. Plasma jets are emitted from both the powered and grounded electrode end; their dynamics are compared and contrasted. Ignition of these jets are quite different; the jet emitted from the powered electrode is ignited with a slight time delay to plasma ignition inside the dielectric tube, while breakdown of the jet at the grounded electrode end is from charging of the dielectric and is therefore dependent on plasma production and transport within the dielectric tube. Present streamer theories can explain these dynamics.

  16. Structural evolution of nanoscale metallic glasses during high-pressure torsion: A molecular dynamics analysis

    Science.gov (United States)

    Feng, S. D.; Jiao, W.; Jing, Q.; Qi, L.; Pan, S. P.; Li, G.; Ma, M. Z.; Wang, W. H.; Liu, R. P.

    2016-11-01

    Structural evolution in nanoscale Cu50Zr50 metallic glasses during high-pressure torsion is investigated using molecular dynamics simulations. Results show that the strong cooperation of shear transformations can be realized by high-pressure torsion in nanoscale Cu50Zr50 metallic glasses at room temperature. It is further shown that high-pressure torsion could prompt atoms to possess lower five-fold symmetries and higher potential energies, making them more likely to participate in shear transformations. Meanwhile, a higher torsion period leads to a greater degree of forced cooperative flow. And the pronounced forced cooperative flow at room temperature under high-pressure torsion permits the study of the shear transformation, its activation and characteristics, and its relationship to the deformations behaviors. This research not only provides an important platform for probing the atomic-level understanding of the fundamental mechanisms of high-pressure torsion in metallic glasses, but also leads to higher stresses and homogeneous flow near lower temperatures which is impossible previously.

  17. Exploring glacier dynamics with subglacial water pressure pulses: Evidence for self-organized criticality?

    Science.gov (United States)

    Kavanaugh, J. L.

    2009-03-01

    In order to determine whether brief excursions, or "pulses," in subglacial water pressure inferred by Kavanaugh and Clarke (2000, 2001) occur, water pressures at the bed of Trapridge Glacier, Yukon, Canada, were recorded using an interface board that continuously monitored a pressure transducer. During the 231 day period between 16 July 2005 and 4 March 2006, more than 7000 pressure pulses were recorded, with magnitudes reaching nearly 3 times the flotation value. Comparison of the pressure pulse record with those from a number of other instruments installed in this soft-bedded glacier indicates that these pulses are generated by stress transients that compress the water within the borehole; calculations suggest that these transients are as large as 75 times the nominal driving stress. Both the magnitudes and interevent times for these pulses are well fitted by power law distributions that are remarkably similar to those exhibited by earthquakes. These similarities suggest that the ice-bed interface of a soft-bedded glacier behaves much like an earthquake fault and raises the possibility that such glaciers self-organize to a critical state. Further evidence for self-organized criticality (SOC) of soft-bedded glaciers is suggested by an examination of well-known ice dynamical properties and the rheological properties of subglacial sediments, which suggests that SOC might be a natural consequence of the rate-independent behavior of subglacial sediments.

  18. Laser-Based Dynamic Compression of Geological Materials to Ultrahigh Pressures

    Science.gov (United States)

    Duffy, T. S.

    2015-12-01

    Laser-based dynamic compression provides new opportunities to study the structures and properties of geological materials to ultrahigh pressure conditions reaching 1 terapascal and beyond. By controlling the shape and duration of the incident laser pulse, either shock or ramp (shockless) loading can be produced. Samples can be compressed for ~10s of nanoseconds on spatial scales of ~1 millimeter. Diagnostics include velocity interferometry from which the stress-density response of the material can be determined and X-ray diffraction from which lattice-level structural information is obtained. Our experiments are being carried out at a suite of facilities including the Omega Laser (U. of Rochester), Linear Coherent Light Source (LCLS), and National Ignition Facility (Livermore). Using ramp compression we have constrained pressure-density states in a variety of materials including iron, magnesium oxide, and carbon. X-ray diffraction has been used as a diagnostic to probe the B1-B2 phase transition in MgO under both ramp and shock loading to multi-megabar pressures. We have also examined this same phase transition at more modest pressures on sodium chloride at the LCLS, observing both the B1-B2 transition upon compression and its back transformation upon release. X-ray diffraction measurements have also been used to study the melting curves and high-pressure phase stability of transition metals and alloys, including compositions relevant to the cores of Earth and super-Earth planets.

  19. A mimetic finite difference method for two-phase flow models with dynamic capillary pressure and hysteresis

    CERN Document Server

    Zhang, Hong

    2016-01-01

    Saturation overshoot and pressure overshoot are studied by incorporating dynamic capillary pressure, capillary pressure hysteresis and hysteretic dynamic coefficient with a traditional fractional flow equation. Using the method of lines, the discretizations are constructed by applying Castillo-Grone's mimetic operators in the space direction and explicit trapezoidal integrator in the time direction. Convergence tests and conservation property of the schemes are presented. Computed profiles capture both the saturation overshoot and pressure overshoot phenomena. Comparisons between numerical results and experiments illustrate the effectiveness and different features of the models.

  20. Heart rate variability and blood pressure during dynamic and static exercise at similar heart rate levels.

    Science.gov (United States)

    Weippert, Matthias; Behrens, Kristin; Rieger, Annika; Stoll, Regina; Kreuzfeld, Steffi

    2013-01-01

    Aim was to elucidate autonomic responses to dynamic and static (isometric) exercise of the lower limbs eliciting the same moderate heart rate (HR) response. 23 males performed two kinds of voluntary exercise in a supine position at similar heart rates: static exercise (SE) of the lower limbs (static leg press) and dynamic exercise (DE) of the lower limbs (cycling). Subjective effort, systolic (SBP) and diastolic blood pressure (DBP), mean arterial pressure (MAP), rate pressure product (RPP) and the time between consecutive heart beats (RR-intervals) were measured. Time-domain (SDNN, RMSSD), frequency-domain (power in the low and high frequency band (LFP, HFP)) and geometric measures (SD1, SD2) as well as non-linear measures of regularity (approximate entropy (ApEn), sample entropy (SampEn) and correlation dimension D2) were calculated. Although HR was similar during both exercise conditions (88±10 bpm), subjective effort, SBP, DBP, MAP and RPP were significantly enhanced during SE. HRV indicators representing overall variability (SDNN, SD 2) and vagal modulated variability (RMSSD, HFP, SD 1) were increased. LFP, thought to be modulated by both autonomic branches, tended to be higher during SE. ApEn and SampEn were decreased whereas D2 was enhanced during SE. It can be concluded that autonomic control processes during SE and DE were qualitatively different despite similar heart rate levels. The differences were reflected by blood pressure and HRV indices. HRV-measures indicated a stronger vagal cardiac activity during SE, while blood pressure response indicated a stronger sympathetic efferent activity to the vessels. The elevated vagal cardiac activity during SE might be a response mechanism, compensating a possible co-activation of sympathetic cardiac efferents, as HR and LF/HF was similar and LFP tended to be higher. However, this conclusion must be drawn cautiously as there is no HRV-marker reflecting "pure" sympathetic cardiac activity.

  1. On structural and lattice dynamic stability of LaF{sub 3} under high pressure: A first principle study

    Energy Technology Data Exchange (ETDEWEB)

    Sahoo, B. D., E-mail: bdsahoo@barc.gov.in; Joshi, K. D.; Gupta, Satish C. [Applied Physics Division, Bhabha Atomic Research Centre, Mumbai-400085 (India)

    2015-06-24

    Structural and lattice dynamical stability of the LaF3 has been analyzed as a function of hydrostatic compression through first principle electronic band structure calculations. The comparison of enthalpies of various plausible structures calculated at various pressures suggests a phase transition from ambient condition tysonite structure (space group P-3c1) to a primitive orthorhombic structure (space group Pmmn) at a pressure of ∼19.5 GPa, in line with the experimental value of 16 GPa. Further, it is predicted that this phase will remain stable up to 100 GPa (the maximum pressure up to which calculations have been performed in the present work). The theoretically determined equation of state displays a good agreement with experimental data. Various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus have been derived from the theoretically determined equation of state and compared with the available experimental data. Our lattice dynamic calculations correctly demonstrate that at zero pressure the tysonite structure is lattice dynamically stable whereas the Pmmn structure is unstable lattice dynamically. Further, at transition pressure the theoretically calculated phonon spectra clearly show that the Pmmn phase emerges as lattice dynamically stable phase whereas the tysonite structure becomes unstable dynamically, supporting our static lattice calculations.

  2. On structural and lattice dynamic stability of LaF3 under high pressure: A first principle study

    Science.gov (United States)

    Sahoo, B. D.; Joshi, K. D.; Gupta, Satish C.

    2015-06-01

    Structural and lattice dynamical stability of the LaF3 has been analyzed as a function of hydrostatic compression through first principle electronic band structure calculations. The comparison of enthalpies of various plausible structures calculated at various pressures suggests a phase transition from ambient condition tysonite structure (space group P-3c1) to a primitive orthorhombic structure (space group Pmmn) at a pressure of ˜19.5 GPa, in line with the experimental value of 16 GPa. Further, it is predicted that this phase will remain stable up to 100 GPa (the maximum pressure up to which calculations have been performed in the present work). The theoretically determined equation of state displays a good agreement with experimental data. Various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus have been derived from the theoretically determined equation of state and compared with the available experimental data. Our lattice dynamic calculations correctly demonstrate that at zero pressure the tysonite structure is lattice dynamically stable whereas the Pmmn structure is unstable lattice dynamically. Further, at transition pressure the theoretically calculated phonon spectra clearly show that the Pmmn phase emerges as lattice dynamically stable phase whereas the tysonite structure becomes unstable dynamically, supporting our static lattice calculations.

  3. Pore-pressure sensitivities to dynamic strains: observations in active tectonic regions

    Science.gov (United States)

    Barbour, Andrew J.

    2015-01-01

    Triggered seismicity arising from dynamic stresses is often explained by the Mohr-Coulomb failure criterion, where elevated pore pressures reduce the effective strength of faults in fluid-saturated rock. The seismic response of a fluid-rock system naturally depends on its hydro-mechanical properties, but accurately assessing how pore-fluid pressure responds to applied stress over large scales in situ remains a challenging task; hence, spatial variations in response are not well understood, especially around active faults. Here I analyze previously unutilized records of dynamic strain and pore-pressure from regional and teleseismic earthquakes at Plate Boundary Observatory (PBO) stations from 2006 through 2012 to investigate variations in response along the Pacific/North American tectonic plate boundary. I find robust scaling-response coefficients between excess pore pressure and dynamic strain at each station that are spatially correlated: around the San Andreas and San Jacinto fault systems, the response is lowest in regions of the crust undergoing the highest rates of secular shear strain. PBO stations in the Parkfield instrument cluster are at comparable distances to the San Andreas fault (SAF), and spatial variations there follow patterns in dextral creep rates along the fault, with the highest response in the actively creeping section, which is consistent with a narrowing zone of strain accumulation seen in geodetic velocity profiles. At stations in the San Juan Bautista (SJB) and Anza instrument clusters, the response depends non-linearly on the inverse fault-perpendicular distance, with the response decreasing towards the fault; the SJB cluster is at the northern transition from creeping-to-locked behavior along the SAF, where creep rates are at moderate to low levels, and the Anza cluster is around the San Jacinto fault, where to date there have been no statistically significant creep rates observed at the surface. These results suggest that the strength

  4. Dynamic cerebral autoregulation to induced blood pressure changes in human experimental and clinical sepsis.

    Science.gov (United States)

    Berg, Ronan M G; Plovsing, Ronni R; Bailey, Damian M; Holstein-Rathlou, Niels-Henrik; Møller, Kirsten

    2016-11-01

    Previous studies have demonstrated that dynamic cerebral autoregulation to spontaneous fluctuations in blood pressure is enhanced following lipopolysaccharide (LPS) infusion, a human experimental model of early sepsis, whereas by contrast it is impaired in patients with severe sepsis or septic shock. In this study, we hypothesized that this pattern of response would be identical during induced changes in blood pressure. Dynamic cerebral autoregulation was assessed in nine healthy volunteers and six septic patients. The healthy volunteers underwent a 4-h intravenous infusion of LPS (total dose: 2 ng kg(-1) ). Mean arterial blood pressure (MAP, arterial transducer) and middle cerebral artery blood flow velocity (MCAv, transcranial Doppler ultrasound) were recorded continuously during thigh-cuff deflation-induced changes in MAP for the determination of a modified rate of regulation (RoR). This was performed before and after LPS infusion in healthy volunteers, and within 72 h following clinical diagnosis of sepsis in patients. In healthy volunteers, thigh-cuff deflation caused a MAP reduction of 16 (13-20) % at baseline and 18 (16-20) % after LPS, while the MAP reduction was 12 (11-13) % in patients (Psepsis, they remain inconclusive with regard to more advanced stages of disease, because thigh-cuff deflation failed to induce sufficient MAP reductions in patients. © 2015 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

  5. Nonlinear fractal dynamics of human colonic pressure activity based upon the box-counting method.

    Science.gov (United States)

    Yan, Rongguo; Guo, Xudong

    2013-01-01

    The computational fractal dimension of human colonic pressure activity acquired by a telemetric capsule robot under normal physiological conditions was studied using the box-counting method. The fractal dimension is a numeric value that quantifies to measure how rough the signal is from nonlinear dynamics, rather than its amplitude or other linear statistical features. The colonic pressure activities from the healthy subject during three typical periods were analysed. The results showed that the activity might be fractal with a non-integer fractal dimension after it being integrated over time using the cumsum method, which was never revealed before. Moreover, the activity (after it being integrated) acquired soon after wakening up was the roughest (also the most complex one) with the largest fractal dimension, closely followed by that acquired during sleep with that acquired long time after awakening up (in the daytime) ranking third with the smallest fractal dimension. Fractal estimation might provide a new method to learn the nonlinear dynamics of human gastrointestinal pressure recordings.

  6. Relationship between muscle stress and intramuscular pressure during dynamic muscle contractions.

    Science.gov (United States)

    Ward, Samuel R; Davis, Jennifer; Kaufman, Kenton R; Lieber, Richard L

    2007-09-01

    Intramuscular pressure (IMP) has been used to estimate muscle stress indirectly. However, the ability of this technique to estimate muscle stress under dynamic conditions is poorly characterized. Therefore, the purpose of this study was to determine the extent to which IMP is a valid surrogate for muscle stress during dynamic contractions. IMP and muscle stress were compared under steady-state isotonic conditions and during complex dynamic length changes. During concentric contractions the shape of the IMP-velocity curve mimicked the basic shape of the force-velocity curve but with much higher variability. For eccentric contractions, a precipitous drop in IMP was observed despite increased muscle stress. The dissociation between muscle stress and IMP during dynamic contractions was partially explained by sensor movement. When the muscle was not moving, IMP explained 89% +/- 5% of the variance in muscle force. However, when transducer movement occurred the linear relationship between IMP and stress was no longer observed. These findings demonstrate the difficulty in interpreting IMP under dynamic conditions when sensor movement occurs. They also illustrate the need to control transducer movement if muscle stress is to be inferred from IMP measurements such as might be desired during clinical gait testing.

  7. Comparison of arterial pressure and plethysmographic waveform-based dynamic preload variables in assessing fluid responsiveness and dynamic arterial tone in patients undergoing major hepatic resection

    NARCIS (Netherlands)

    Vos, J. J.; Kalmar, A. F.; Struys, M. M. R. F.; Wietasch, J. K. G.; Hendriks, H. G. D.; Scheeren, T. W. L.

    2013-01-01

    Dynamic preload variables to predict fluid responsiveness are based either on the arterial pressure waveform (APW) or on the plethysmographic waveform (PW). We compared the ability of APW-based variations in stroke volume (SVV) and pulse pressure (PPV) and of PW-based plethysmographic variability in

  8. Comparison of arterial pressure and plethysmographic waveform-based dynamic preload variables in assessing fluid responsiveness and dynamic arterial tone in patients undergoing major hepatic resection

    NARCIS (Netherlands)

    Vos, J. J.; Kalmar, A. F.; Struys, M. M. R. F.; Wietasch, J. K. G.; Hendriks, H. G. D.; Scheeren, T. W. L.

    Dynamic preload variables to predict fluid responsiveness are based either on the arterial pressure waveform (APW) or on the plethysmographic waveform (PW). We compared the ability of APW-based variations in stroke volume (SVV) and pulse pressure (PPV) and of PW-based plethysmographic variability

  9. Comparison of arterial pressure and plethysmographic waveform-based dynamic preload variables in assessing fluid responsiveness and dynamic arterial tone in patients undergoing major hepatic resection

    NARCIS (Netherlands)

    Vos, J. J.; Kalmar, A. F.; Struys, M. M. R. F.; Wietasch, J. K. G.; Hendriks, H. G. D.; Scheeren, T. W. L.

    2013-01-01

    Dynamic preload variables to predict fluid responsiveness are based either on the arterial pressure waveform (APW) or on the plethysmographic waveform (PW). We compared the ability of APW-based variations in stroke volume (SVV) and pulse pressure (PPV) and of PW-based plethysmographic variability in

  10. On the impact of radiation pressure on the dynamics and inner structure of dusty wind-driven shells

    CERN Document Server

    Martinez-Gonzalez, Sergio; Tenorio-Tagle, Guillermo

    2014-01-01

    Massive young stellar clusters are strong sources of radiation and mechanical energy. Their powerful winds and radiation pressure sweep-up interstellar gas into thin expanding shells which trap the ionizing radiation produced by the central clusters affecting the dynamics and the distribution of their ionized gas. Here we continue our comparison of the star cluster winds and radiation pressure effects on the dynamics of shells around young massive clusters. We calculate the impact that radiation pressure has on the distribution of matter and thermal pressure within such shells as well as on the density weighted ionization parameter $U_w$ and put our results on the diagnostic diagram which allows one to discriminate between the wind-dominated and radiation-dominated regimes. We found that model predicted values of the ionization parameter agree well with typical values found in local starburst galaxies. Radiation pressure may affect the inner structure and the dynamics of wind-driven shells only at the earlies...

  11. Dynamic high pressure-induced gelation in milk protein model systems.

    Science.gov (United States)

    Venir, E; Marchesini, G; Biasutti, M; Innocente, N

    2010-02-01

    The structure-functional properties of milk proteins are relevant in food formulation. Recently, there has been growing interest in dynamic high-pressure homogenization effects on the rheological-structural properties of food macromolecules and proteins. The aim of this work was to evaluate the effects of different homogenization pressures on rheological properties of milk protein model systems. For this purpose, sodium caseinate (SC) and whey protein concentrate (WPC) were dispersed at different concentrations (1, 2, and 4%), pasteurized, and then homogenized at 0, 18MPa (conventional pressure, CP), 100MPa (high pressure, HP), and 150MPa (HP+). Differences in viscosity were observed between WPC and casein dispersions according to concentration, heat treatment, and homogenization pressure. Mechanical spectra described the characteristic behavior of solutions except for the WPC 4% pasteurized sample, in which a network formed but was broken after homogenization. Dispersions with different ratios of WPC and SC were also made. In these systems, pasteurization alone did not determine network formation, whereas homogenization alone promoted cold gelation. A total concentration of at least 4% was required for homogenization-induced gelation in pasteurized and unpasteurized samples. Gels with higher elastic modulus (G') were obtained in more concentrated samples, and a bell-shaped behavior with the maximum value at HP was observed. The HP treatment produced stronger gels than the CP treatment. Similar G' values were obtained when different concentrations, pasteurization conditions, and homogenization pressures were combined. Therefore, by setting appropriate process conditions, systems or gels with tailored characteristics may be obtained from dispersions of milk proteins. Copyright 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  12. Wind Pressure Distribution and Wind-induced Dynamic Response for Spatial Groined Latticed Vaults

    Institute of Scientific and Technical Information of China (English)

    MA Jun; ZHOU Dai; BAO Yan

    2008-01-01

    The wind pressure distribution and wind-induced vibration responses of long-span spatial groined latticed vaults (SGLVs) were numerically simulated, which always are ones of the most important problems in the structural wind resistance design. Incompressible visco-fluid model was introduced, and the standard k-εtwo equation model and semi-implicit method for pressure linked equation (SIMPLE) were used to describe the flow turbulence. Furthermore, the structural dynamic equation was set up, which is solved by Newmark-β method. And several sort of wind-induced vibration coefficients such as the wind-induced vibration coefficient corresponding to the nodal displacement responses and wind loads were suggested. In the numerical simulation where the SGLV consisting of the cylindrical sectors with different curved surface was chosen as the example,the influence on the relative wind pressure distribution and structural wind-induced vibration responses of the closed or open SGLV caused by such parameters as the number of cylindrical sectors, structural curvature and the ratio of rise to span was investigated. Finally, some useful conclusions on the local wind pressure distribution on the structural surface and the wind-induced vibration coefficients of SGLV were developed.

  13. High pressure studies on structural and secondary relaxation dynamics in silyl derivative of D-glucose

    Science.gov (United States)

    Minecka, Aldona; Kamińska, Ewa; Tarnacka, Magdalena; Dzienia, Andrzej; Madejczyk, Olga; Waliłko, Patrycja; Kasprzycka, Anna; Kamiński, Kamil; Paluch, Marian

    2017-08-01

    In this paper, broadband dielectric spectroscopy was applied to investigate molecular dynamics of 1,2,3,4,6-penta-O-(trimethylsilyl)-D-glucopyranose (S-GLU) at ambient and elevated pressures. Our studies showed that apart from the structural relaxation, one well resolved asymmetric secondary process (initially labeled as β) is observed in the spectra measured at p = 0.1 MPa. Analysis with the use of the coupling model and criterion proposed by Ngai and Capaccioli indicated that the β-process in S-GLU is probably a Johari-Goldstein relaxation of intermolecular origin. Further high pressure experiments demonstrated that there are in fact two secondary processes contributing to the β-relaxation. Therefore, one can postulate that the coupling model is a necessary, but not sufficient criterion to identify the true nature of the given secondary relaxation process. The role of pressure experiments in better understanding of the molecular origin of local mobility seems to be much more important. Interestingly, our research also revealed that the structural relaxation in S-GLU is very sensitive to compression. It was reflected in an extremely high pressure coefficient of the glass transition temperature (dTg/dp = 412 K/GPa). According to the literature data, such a high value of dTg/dp has not been obtained so far for any H-bonded, van der Waals, or polymeric glass-formers.

  14. Low-dimensional dynamical model for the diversity of pressure patterns used in canary song

    Science.gov (United States)

    Alonso, Leandro M.; Alliende, Jorge A.; Goller, F.; Mindlin, Gabriel B.

    2009-04-01

    During song production, oscine birds produce large air sac pressure pulses. During those pulses, energy is transferred to labia located at the juncture between the bronchii and the trachea, inducing the high frequency labial oscillations which are responsible for airflow modulations, i.e., the uttered sound. In order to generate diverse syllables, canaries (Serinus canaria) use a set of air sac pressure patterns with characteristic shapes. In this work we show that these different shapes can be approximated by the subharmonic solutions of a forced normal form. This simple model is built from identifying dynamical elements which allow to reproduce the shape of the pressure pattern corresponding to one syllable type. Remarkably, integrating that simple model for other parameters allows to recover the other pressure patterns used during song. Interpreting the diversity of these physiological gestures as subharmonic solutions of a simple nonlinear system allows us to account simultaneously for their morphological features as well as for the syllabic timing and suggests a strategy for the generation of complex motor patterns.

  15. [Effect of dynamic high-pressure micro-fluidization on the structure of maize amylose].

    Science.gov (United States)

    Tu, Zong-Cai; Yin, Yue-Bin; Zhang, Qiu; Wang, Hui

    2013-05-01

    The effect of dynamic high-pressure micro-fluidization (DHPM) at 80, 120, 160, and 200 MPa on the structure of maize amylose was investigated using scanning electron microscopy (SEM), atomic force microscope (AFM), Xray diffraction, and FT-IR spectroscopy. SEM analysis showed that the surface appearances of maize amylose were altered and the starch granules were partially congregated together after DHPM treatment. AFM images showed that the treated starch molecules are cross-linked to each other and arranged in a close mesh structure. Xray diffraction spectra and IR spectra indicated that relative crystallinity declined gradually with the pressure increasing. The results provide a theoretical basis for starch modification of DHPM.

  16. Porphyry-copper ore shells form at stable pressure-temperature fronts within dynamic fluid plumes.

    Science.gov (United States)

    Weis, P; Driesner, T; Heinrich, C A

    2012-12-21

    Porphyry-type ore deposits are major resources of copper and gold, precipitated from fluids expelled by crustal magma chambers. The metals are typically concentrated in confined ore shells within vertically extensive vein networks, formed through hydraulic fracturing of rock by ascending fluids. Numerical modeling shows that dynamic permeability responses to magmatic fluid expulsion can stabilize a front of metal precipitation at the boundary between lithostatically pressured up-flow of hot magmatic fluids and hydrostatically pressured convection of cooler meteoric fluids. The balance between focused heat advection and lateral cooling controls the most important economic characteristics, including size, shape, and ore grade. This self-sustaining process may extend to epithermal gold deposits, venting at active volcanoes, and regions with the potential for geothermal energy production.

  17. Molecular Dynamics Simulation of Water Nanodroplets on Silica Surfaces at High Air Pressures

    DEFF Research Database (Denmark)

    Zambrano, Harvey A; Jaffe, Richard Lawrence; Walther, Jens Honore

    2010-01-01

    e.g., nanobubbles. In the present work we study the role of air on the wetting of hydrophilic systems. We conduct molecular dynamics simulations of a water nanodroplet on an amorphous silica surface at different air pressures. The interaction potentials describing the silica, water, and air...... are obtained from the literature. The silica surface is modeled by a large 32 ⨯ 32 ⨯ 2 nm amorphous SiO2 structure consisting of 180000 atoms. The water consists of 18000 water molecules surrounded by N2 and O2 air molecules corresponding to air pressures of 0 bar (vacuum), 50 bar, 100 bar and 200 bar. We...... perform extensive simulations of the water- air equilibrium and calibrate the water-air interaction to match the experimental solubility of N2 and O2 in water. For the silica-water system we calibrate the water-silica interaction to match the experimental contact angle of 27º. We subsequently study...

  18. Monte Carlo Simulation of Laser-Ablated Particle Splitting Dynamic in a Low Pressure Inert Gas

    Science.gov (United States)

    Ding, Xuecheng; Zhang, Zicai; Liang, Weihua; Chu, Lizhi; Deng, Zechao; Wang, Yinglong

    2016-06-01

    A Monte Carlo simulation method with an instantaneous density dependent mean-free-path of the ablated particles and the Ar gas is developed for investigating the transport dynamics of the laser-ablated particles in a low pressure inert gas. The ablated-particle density and velocity distributions are analyzed. The force distributions acting on the ablated particles are investigated. The influence of the substrate on the ablated-particle velocity distribution and the force distribution acting on the ablated particles are discussed. The Monte Carlo simulation results approximately agree with the experimental data at the pressure of 8 Pa to 17 Pa. This is helpful to investigate the gas phase nucleation and growth mechanism of nanoparticles. supported by the Natural Science Foundation of Hebei Province, China (No. A2015201166) and the Natural Science Foundation of Hebei University, China (No. 2013-252)

  19. Molecular Dynamics Simulation of Water Nanodroplets on Silica Surfaces at High Air Pressures

    DEFF Research Database (Denmark)

    Zambrano, Harvey A; Jaffe, Richard Lawrence; Walther, Jens Honore

    2010-01-01

    e.g., nanobubbles. In the present work we study the role of air on the wetting of hydrophilic systems. We conduct molecular dynamics simulations of a water nanodroplet on an amorphous silica surface at different air pressures. The interaction potentials describing the silica, water, and air...... not been reached. Contact angle measurements of droplets on solid surfaces offer useful quantitative measurements of the physiochemical properties of the solid-liquid interface. For hydrophobic systems the properties the solid- liquid interface are now known to be strongly influenced by the presence of air...... are obtained from the literature. The silica surface is modeled by a large 32 ⨯ 32 ⨯ 2 nm amorphous SiO2 structure consisting of 180000 atoms. The water consists of 18000 water molecules surrounded by N2 and O2 air molecules corresponding to air pressures of 0 bar (vacuum), 50 bar, 100 bar and 200 bar. We...

  20. Fluid description of Weibel-type instabilities via full pressure tensor dynamics

    Science.gov (United States)

    Sarrat, M.; Del Sarto, D.; Ghizzo, A.

    2016-08-01

    We discuss a fluid model for the description of Weibel-type instabilties based on the inclusion of the full pressure tensor dynamics. The linear analysis first performed by Basu B., Phys. Plasmas, 9, (2002) 5131, for the strong anisotropy limit of Weibel's instability is extended to include the coupling between pure Weibel's and current filamentation instability, and the potential of this fluid approach is further developed. It is shown to allow an easier interpretation of some physical features of these coupled modes, notably the role played by thermal effects. It can be used to identify the role of different closure conditions in pressure-driven instabilities which can be numerically investigated at a remarkably lower computational cost than with kinetic simulations.

  1. Pressure tensor dynamics in the fluid description of Weibel-type instabilities

    Science.gov (United States)

    Sarrat, Mathieu; Del Sarto, Daniele; Ghizzo, Alain

    2016-10-01

    The study of Weibel-type instabilities triggered by temperature or momentum anisotropy normally requires a full kinetic treatement, though reduced kinetic models often provide an efficient alternative, both from a computational point of view and thanks to a simplified analysis that helps a better physical insight. We here show how, similarly to reduced kinetic models, an extended fluid model including the full pressure tensor dynamics provides a consistent description of Weibel-type modes in presence of two counterstreaming, non-relativistic beams with initially anisotropic pressures: focussing on propagation transverse and parallel to the beams we discuss the fluid dispersion relation of Weibel Instability-Current Filamentation Instability coupled modes and of the time resonant Weibel instability. This fluid analysis is shown to agree with the kinetic result and to allow the identification of some thermal effects, whose interpretation appeared more difficult in full kinetic descriptions.

  2. Role of secondary emission on discharge dynamics in an atmospheric pressure dielectric barrier discharge

    Energy Technology Data Exchange (ETDEWEB)

    Tay, W. H.; Kausik, S. S.; Yap, S. L.; Wong, C. S., E-mail: cswong@um.edu.my [Plasma Technology Research Centre, Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2014-04-15

    The discharge dynamics in an atmospheric pressure dielectric barrier discharge (DBD) is studied in a DBD reactor consisting of a pair of stainless steel parallel plate electrodes. The DBD discharge has been generated by a 50 Hz ac high voltage power source. The high-speed intensified charge coupled device camera is used to capture the images of filaments occurring in the discharge gap. It is observed that frequent synchronous breakdown of micro discharges occurs across the discharge gap in the case of negative current pulse. The experimental results reveal that secondary emissions from the dielectric surface play a key role in the synchronous breakdown of plasma filaments.

  3. Dynamic multi-planar EPI of the urinary bladder during voiding with simultaneous detrusor pressure measurement.

    Science.gov (United States)

    Simmons, A; Williams, S C; Craggs, M; Andrew, C; Gregory, L; Allin, M; Mundy, A; Leaker, B

    1997-01-01

    Magnetic resonance imaging gives high quality images of the urinary bladder with excellent contrast. We report here the first application of dynamic, multi-slice, echo planar imaging to a study of urinary bladder emptying. Changes in urinary bladder volumes and rates of urine expulsion from the bladder have been measured simultaneously with bladder pressure. The method shows promise for clinical applications involving compromised bladder function, for reappraising bladder contraction strength-volume relationships, and for investigating the rate of change of length, three-dimensional shape, and wall tension in different parts of the bladder during micturition.

  4. Evaluation of Vapor Pressure Estimation Methods for Use in Simulating the Dynamic of Atmospheric Organic Aerosols

    Directory of Open Access Journals (Sweden)

    A. J. Komkoua Mbienda

    2013-01-01

    Lee and Kesler (LK, and Ambrose-Walton (AW methods for estimating vapor pressures ( are tested against experimental data for a set of volatile organic compounds (VOC. required to determine gas-particle partitioning of such organic compounds is used as a parameter for simulating the dynamic of atmospheric aerosols. Here, we use the structure-property relationships of VOC to estimate . The accuracy of each of the aforementioned methods is also assessed for each class of compounds (hydrocarbons, monofunctionalized, difunctionalized, and tri- and more functionalized volatile organic species. It is found that the best method for each VOC depends on its functionality.

  5. Dynamic response of large increased pressure wind tunnel rotor-gear coupling system with parallel misalignment

    Institute of Scientific and Technical Information of China (English)

    DONG Guo-qing; CUI Ya-hui; WANG Zhong-ren; LIU Zhan-sheng; SHEN Ji-quan

    2008-01-01

    To study the misalignment of gear coupling, this paper analyzed the distortion of the tooth of gear coupling on the base of gear coupling's motion under parallel misalignment, and derived the specific expression of additive radial force, which produced by the rotor' torque. The motion differential equations of the large in-creased pressure wind tunnel rotor-gear coupling system were derived by the finite element method. Newmark integral method was applied to calculate the dynamic response of the system with parallel misalignment. The nu-merical results show that: under the effect of additive radial force, the static misalignment can arouse 2X fre-quency component lateral vibration; the dynamic misalignment can arouse2X,4X,6X multiple frequency compo-nents lateral vibration. The 2X frequency component is obvious. The additive radial force of the gear coupling can arouse lateral vibration with even multiple frequency components.

  6. Atomic and dislocation dynamics simulations of plastic deformation in reactor pressure vessel steel

    Science.gov (United States)

    Monnet, Ghiath; Domain, Christophe; Queyreau, Sylvain; Naamane, Sanae; Devincre, Benoit

    2009-11-01

    The collective behavior of dislocations in reactor pressure vessel (RPV) steel involves dislocation properties on different phenomenological scales. In the multiscale approach, adopted in this work, we use atomic simulations to provide input data for larger scale simulations. We show in this paper how first-principles calculations can be used to describe the Peierls potential of screw dislocations, allowing for the validation of the empirical interatomic potential used in molecular dynamics simulations. The latter are used to compute the velocity of dislocations as a function of the applied stress and the temperature. The mobility laws obtained in this way are employed in dislocation dynamics simulations in order to predict properties of plastic flow, namely dislocation-dislocation interactions and dislocation interactions with carbides at low and high temperature.

  7. Atomic and dislocation dynamics simulations of plastic deformation in reactor pressure vessel steel

    Energy Technology Data Exchange (ETDEWEB)

    Monnet, Ghiath, E-mail: ghiathmonnet@yahoo.f [EDF-R and D, MMC, Avenue des Renardieres, 77818 Moret sur Loing (France); Domain, Christophe; Queyreau, Sylvain; Naamane, Sanae [EDF-R and D, MMC, Avenue des Renardieres, 77818 Moret sur Loing (France); Devincre, Benoit [LEM, CNRS-ONERA, 29 av. de la division Leclerc, 92130 Chatillon (France)

    2009-11-15

    The collective behavior of dislocations in reactor pressure vessel (RPV) steel involves dislocation properties on different phenomenological scales. In the multiscale approach, adopted in this work, we use atomic simulations to provide input data for larger scale simulations. We show in this paper how first-principles calculations can be used to describe the Peierls potential of screw dislocations, allowing for the validation of the empirical interatomic potential used in molecular dynamics simulations. The latter are used to compute the velocity of dislocations as a function of the applied stress and the temperature. The mobility laws obtained in this way are employed in dislocation dynamics simulations in order to predict properties of plastic flow, namely dislocation-dislocation interactions and dislocation interactions with carbides at low and high temperature.

  8. Two-dimensional vertical moisture-pressure dynamics above groundwater waves: Sand flume experiments and modelling

    Science.gov (United States)

    Shoushtari, Seyed Mohammad Hossein Jazayeri; Cartwright, Nick; Perrochet, Pierre; Nielsen, Peter

    2017-01-01

    of moisture content relative to the suction head was observed indicating that the response time of the moisture content to watertable motion is greater than that of the pore water pressure. The observed moisture-pressure dynamics are qualitatively reproduced using a hysteretic Richards' equation model. However, quantitative differences exist which are likely to be due to previous findings that demonstrated that the Richards' equation model is unable to accurately reproduce the observed watertable wave dispersion, particularly at shorter period oscillations.

  9. Effect of Nasal Obstruction on Continuous Positive Airway Pressure Treatment: Computational Fluid Dynamics Analyses.

    Directory of Open Access Journals (Sweden)

    Tadashi Wakayama

    Full Text Available Nasal obstruction is a common problem in continuous positive airway pressure (CPAP therapy for obstructive sleep apnea and limits treatment compliance. The purpose of this study is to model the effects of nasal obstruction on airflow parameters under CPAP using computational fluid dynamics (CFD, and to clarify quantitatively the relation between airflow velocity and pressure loss coefficient in subjects with and without nasal obstruction.We conducted an observational cross-sectional study of 16 Japanese adult subjects, of whom 9 had nasal obstruction and 7 did not (control group. Three-dimensional reconstructed models of the nasal cavity and nasopharynx with a CPAP mask fitted to the nostrils were created from each subject's CT scans. The digital models were meshed with tetrahedral cells and stereolithography formats were created. CPAP airflow simulations were conducted using CFD software. Airflow streamlines and velocity contours in the nasal cavities and nasopharynx were compared between groups. Simulation models were confirmed to agree with actual measurements of nasal flow rate and with pressure and flow rate in the CPAP machine.Under 10 cmH2O CPAP, average maximum airflow velocity during inspiration was 17.6 ± 5.6 m/s in the nasal obstruction group but only 11.8 ± 1.4 m/s in the control group. The average pressure drop in the nasopharynx relative to inlet static pressure was 2.44 ± 1.41 cmH2O in the nasal obstruction group but only 1.17 ± 0.29 cmH2O in the control group. The nasal obstruction and control groups were clearly separated by a velocity threshold of 13.5 m/s, and pressure loss coefficient threshold of approximately 10.0. In contrast, there was no significant difference in expiratory pressure in the nasopharynx between the groups.This is the first CFD analysis of the effect of nasal obstruction on CPAP treatment. A strong correlation between the inspiratory pressure loss coefficient and maximum airflow velocity was found.

  10. Dynamic range and sensitivity of field emission pressure sensors with non-silicon membranes

    Energy Technology Data Exchange (ETDEWEB)

    Badi, N., E-mail: nbadi@uh.edu [Center for Advanced Materials (CAM), University of Houston, Houston, TX 77204-5004 (United States); Physics Department, University of Houston, Houston, TX 77204-5005 (United States); Bensaoula, A. [Physics Department, University of Houston, Houston, TX 77204-5005 (United States); Nair, A.M. [Center for Advanced Materials (CAM), University of Houston, Houston, TX 77204-5004 (United States)

    2013-11-15

    We report on the dynamic range and sensitivity simulations of a functional field emission-based pressure sensor. The device comprises a titanium nitride membrane acting as the anode in front of a flat boron nitride cold cathode emitter. We previously reported the problem of non-linearity of these sensors and studied their performance for different membrane geometries and membranes using different materials such as Si, Ti, Ta, and TiN [N. Badi et al., Appl. Surf. Sci. 256 (2010) 4990–4994]. Of the materials investigated, TiN seems to have the most desirable characteristics with respect to linearity. In this paper we report on the effects of membrane dimensions on the sensor operation. Results show how a sensor having a TiN membrane of standard dimension can be tuned during operation to have maximum dynamic range without affecting the sensitivity. The membrane dimensions have a strong effect on the device dynamic range. Small portions of the entire range could however be selected by changing the device operating voltage. We also have shown that smaller area membranes result in devices with better response in terms of constant sensitivity, as compared to those with thicker membranes. The device can be operated over its entire dynamic range by tuning the operating voltage of the device to keep the sensitivity a constant.

  11. Molecular Dynamics Simulations of Liquid Phosphorus at High Temperature and Pressure

    Institute of Scientific and Technical Information of China (English)

    WU Yan-Ning; ZHAO Gang; LIU Chang-Song; ZHU Zhen-Gang

    2008-01-01

    By performing ab initio molecular dynamics simulations, we have investigated the mierostructure, dynam-ical and electronic properties of liquid phosphorus (P) under high temperature and pressure. In our simulations, the calculated coordination number (CN) changes discontinuously with density, and seems to increase rapidly after liquid P is compressed to 2.5 g/cm3. Under compression, liquid P shows the first-order liquid-liquid phase transition from the molecular liquid composed of the tetrahedral P4 molecules to complex polymeric form with three-dimensional network structure, accompanied by the nonmetal to metal transition of the electronic structure. The order parameters Q6 and Q4 are sensitive to the microstructural change of liquid P. By calculating diffusion coefficients, we show the dynamical anomaly of liquid P by compression. At lower temperatures, a maximum exists at the diffusion coefficients as a function of density; at higher temperatures, the anomalous behavior is weakened. The excess entropy shows the same phenom-ena as the diffusion coefficients. By analysis of the angle distribution functions and angular limited triplet correlation functions, we can clearly find that the Peierls distortion in polymeric form of liquid P is reduced by further compression.

  12. Final Report DE-FG02-00ER54583: "Physics of Atmospheric Pressure Glow Discharges" and "Nanoparticle Nucleation and Dynamics in Low-Pressure Plasmas"

    Energy Technology Data Exchange (ETDEWEB)

    Uwe Kortshagen; Joachim Heberlein; Steven L. Girshick

    2009-06-01

    This project was funded over two periods of three years each, with an additional year of no-cost extension. Research in the first funding period focused on the physics of uniform atmospheric pressure glow discharges, the second funding period was devoted to the study of the dynamics of nanometer-sized particles in plasmas.

  13. Dynamic arterial elastance predicts mean arterial pressure decrease associated with decreasing norepinephrine dosage in septic shock.

    Science.gov (United States)

    Guinot, Pierre-Grégoire; Bernard, Eugénie; Levrard, Mélanie; Dupont, Hervé; Lorne, Emmanuel

    2015-01-19

    Gradual reduction of the dosage of norepinephrine (NE) in patients with septic shock is usually left to the physician's discretion. No hemodynamic indicator predictive of the possibility of decreasing the NE dosage is currently available at the bedside. The respiratory pulse pressure variation/respiratory stroke volume variation (dynamic arterial elastance (Eadyn)) ratio has been proposed as an indicator of vascular tone. The purpose of this study was to determine whether Eadyn can be used to predict the decrease in arterial pressure when decreasing the NE dosage in resuscitated sepsis patients. A prospective study was carried out in a university hospital intensive care unit. All consecutive patients with septic shock monitored by PICCO2 for whom the intensive care physician planned to decrease the NE dosage were enrolled. Measurements of hemodynamic and PICCO2 variables were obtained before/after decreasing the NE dosage. Responders were defined by a >15% decrease in mean arterial pressure (MAP). In total, 35 patients were included. MAP decreased by >15% after decreasing the NE dosage in 37% of patients (n = 13). Clinical characteristics appeared to be similar between responders and nonresponders. Eadyn was lower in responders than in nonresponders (0.75 (0.69 to 0.85) versus 1 (0. 83 to 1.22), P decrease in arterial pressure, with an area under the receiver-operating characteristic curve of 0.87 (95% confidence interval (95% CI): 0.72 to 0.96; P decrease in arterial pressure in response to NE dose reduction. Eadyn may constitute an easy-to-use functional approach to arterial-tone assessment, which may be helpful to identify patients likely to benefit from NE dose reduction.

  14. High Pressure Sensing and Dynamics Using High Speed Fiber Bragg Grating Interrogation Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, G. [LANL; Sandberg, R. L. [LANL; Lalone, B. M. [NSTec; Marshall, B. R. [NSTec; Grover, M. [NSTec; Stevens, G. D. [NSTec; Udd, E. [Columbia Gorge Research

    2014-06-01

    Fiber Bragg gratings (FBGs) are developing into useful sensing tools for measuring high pressure dynamics in extreme environments under shock loading conditions. Approaches using traditional diode array coupled FBG interrogation systems are often limited to readout speeds in the sub-MHz range. For shock wave physics, required detection speeds approaching 100 MHz are desired. We explore the use of two types of FBG sensing systems that are aimed at applying this technology as embedded high pressure probes for transient shock events. Both approaches measure time resolved spectral shifts in the return light from short (few mm long) uniform FBGs at 1550 nm. In the first approach, we use a fiber coupled spectrometer to demultiplex spectral channels into an array (up to 12) of single element InGaAs photoreceivers. By monitoring the detectors during a shock impact event with high speed recording, we are able to track the pressure induced spectral shifting in FBG down to a time resolution of 20 ns. In the second approach, developed at the Special Technologies Lab, a coherent mode-locked fiber laser is used to illuminate the FBG sensor. After the sensor, wavelength-to-time mapping is accomplished with a chromatic dispersive element, and entire spectra are sampled using a single detector at the modelocked laser repetition rate of 50 MHz. By sampling with a 12 GHz InGaAs detector, direct wavelength mapping in time is recorded, and the pressure induced FBG spectral shift is sampled at 50 MHz. Here, the sensing systems are used to monitor the spectral shifts of FBGs that are immersed into liquid water and shock compressed using explosives. In this configuration, the gratings survive to pressures approaching 50 kbar. We describe both approaches and present the measured spectral shifts from the shock experiments.

  15. The effect of a dynamic PCL brace on patellofemoral compartment pressures in PCL-and PCL/PLC-deficient knees.

    Science.gov (United States)

    Welch, Tyler; Keller, Thomas; Maldonado, Ruben; Metzger, Melodie; Mohr, Karen; Kvitne, Ronald

    2017-12-01

    The natural history of posterior cruciate ligament (PCL) deficiency includes the development of arthrosis in the patellofemoral joint (PFJ). The purpose of this biomechanical study was to evaluate the hypothesis that dynamic bracing reduces PFJ pressures in PCL- and combined PCL/posterolateral corner (PLC)-deficient knees. Controlled Laboratory Study. Eight fresh frozen cadaveric knees with intact cruciate and collateral ligaments were included. PFJ pressures and force were measured using a pressure mapping system via a lateral arthrotomy at knee flexion angles of 30°, 60°, 90°, and 120° in intact, PCL-deficient, and PCL/PLC-deficient knees under a combined quadriceps/hamstrings load of 400 N/200 N. Testing was then repeated in PCL- and PCL/PLC-deficient knees after application of a dynamic PCL brace. Application of a dynamic PCL brace led to a reduction in peak PFJ pressures in PCL-deficient knees. In addition, the brace led to a significant reduction in peak pressures in PCL/PLC-deficient knees at 60°, 90°, and 120° of flexion. Application of the dynamic brace also led to a reduction in total PFJ force across all flexion angles for both PCL- and PCL/PLC-deficient knees. Dynamic bracing reduces PFJ pressures in PCL- and combined PCL/PLC-deficient knees, particularly at high degrees of knee flexion.

  16. Monro-Kellie 2.0: The dynamic vascular and venous pathophysiological components of intracranial pressure

    Science.gov (United States)

    2016-01-01

    For 200 years, the ‘closed box’ analogy of intracranial pressure (ICP) has underpinned neurosurgery and neuro-critical care. Cushing conceptualised the Monro-Kellie doctrine stating that a change in blood, brain or CSF volume resulted in reciprocal changes in one or both of the other two. When not possible, attempts to increase a volume further increase ICP. On this doctrine’s “truth or relative untruth” depends many of the critical procedures in the surgery of the central nervous system. However, each volume component may not deserve the equal weighting this static concept implies. The slow production of CSF (0.35 ml/min) is dwarfed by the dynamic blood in and outflow (∼700 ml/min). Neuro-critical care practice focusing on arterial and ICP regulation has been questioned. Failure of venous efferent flow to precisely match arterial afferent flow will yield immediate and dramatic changes in intracranial blood volume and pressure. Interpreting ICP without interrogating its core drivers may be misleading. Multiple clinical conditions and the cerebral effects of altitude and microgravity relate to imbalances in this dynamic rather than ICP per se. This article reviews the Monro-Kellie doctrine, categorises venous outflow limitation conditions, relates physiological mechanisms to clinical conditions and suggests specific management options. PMID:27174995

  17. Effects of sediment on the dynamic pressure of water and sediment on dams

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    After a reservoir has been in operation for a period of time,a sediment layer is likely formed before the dam. Since studies of the effects of sediment layers on the hydrodynamic pressures of impounded water and the aseismic responses of dam are few,the dynamic effect of sediment may be applied neither in the seismic design of new dams nor in the assessment of earthquake safety of existing dams. However,a common practice of the action of sediment layers and foundation is based on a partial energy absorption boundary. It is shown that during a vertical harmonic ground motion,the sediment layer could alter the natural frequencies of reservoir. The dynamic pressure on a rigid vertical dam face caused by the vertical ground motion is obtained through a computational model and an experimental test by using a shaking table. With a change in the thickness of sediment,the frequency corresponding to the inertia amplification effect appears to vary gradually. The results are useful for further study of seismic responses of dams.

  18. Modelling the Dynamic Interaction Power System Lamp - Application to High Pressure Mercury Gas Discharge Lamps

    Directory of Open Access Journals (Sweden)

    ZIANE, M.

    2007-11-01

    Full Text Available The aim of this paper is to study the dynamic behaviour of a plant constituted by an electrical power system and a gas discharge lamp, this latter, increasingly used in street lighting, remains a nonlinear load element. Various approaches are used to represent it, one is the approximation of the discharge represented by a hot "channel", which verifies the assumption of local thermodynamic equilibrium [LTE] or the polynomial form of the conductance variation. A calculation procedure, based on "channel" approximation of the high pressure mercury (HPM gas-discharge lamp, is developed to determine the physical and electric magnitudes, which characterize the dynamic behavior of the couple "lamp-electrical power system". The evolution of the lamp properties when principal parameters of the discharge (pressure of mercury, voltage supply, frequency are varying were studied and analyzed. We show the concordance between simulation, calculations and measurements for electric, energetic or irradiative characteristics. The model reproduces well the evolution of properties of the supply when principal parameters of the discharge vary.

  19. Pick-up ion pressure gradients modulating the solar wind dynamics

    Science.gov (United States)

    Fahr, Hans J.; Fichtner, Horst

    1995-01-01

    Neutral interstellar atoms penetrate deeply into the inner heliosphere before they become ionized by various processes. As ions they are picked-up by the frozen-in magnetic fields and are convected outwards with the solar wind plasma. Thereby the primary plasma flow is mass, momentum, and energy-loaded. The dynamics of the distant multi-constituent solar wind is, however, not solely determined by these loading processes, but is also affected by the wave-mediated pick-up ion pressure gradients derivable from the pick-up ion distribution function. The action of the radial components of these pressures essentially counter balances the decelerating effect of the solar wind momentum loading, diminishing strongly the deceleration of the distant solar wind. Furthermore the latitudinal components of the pick-up ion pressures induce latitudinal forces acting on the multiconstituent solar plasma outflow and inducing nonradial bulk flow components. The enforced nonradial outflow geometry on the upwind hemisphere may partly be responsible for the magnetic flux deficit which was claimed since several years in the PIONEER-10 magnetic flux data.

  20. Nonequilibrium molecular dynamics simulation of pressure-driven water transport through modified CNT membranes

    Science.gov (United States)

    Wang, Luying; Dumont, Randall S.; Dickson, James M.

    2013-03-01

    Nonequilibrium molecular dynamics (NEMD) simulations are presented to investigate the effect of water-membrane interactions on the transport properties of pressure-driven water flow passing through carbon nanotube (CNT) membranes. The CNT membrane is modified with different physical properties to alter the van der Waals interactions or the electrostatic interactions between water molecules and the CNT membranes. The unmodified and modified CNT membranes are models of simplified nanofiltration (NF) membranes at operating conditions consistent with real NF systems. All NEMD simulations are run with constant pressure difference (8.0 MPa) temperature (300 K), constant pore size (0.643 nm radius for CNT (12, 12)), and membrane thickness (6.0 nm). The water flow rate, density, and velocity (in flow direction) distributions are obtained by analyzing the NEMD simulation results to compare transport through the modified and unmodified CNT membranes. The pressure-driven water flow through CNT membranes is from 11 to 21 times faster than predicted by the Navier-Stokes equations. For water passing through the modified membrane with stronger van der Waals or electrostatic interactions, the fast flow is reduced giving lower flow rates and velocities. These investigations show the effect of water-CNT membrane interactions on water transport under NF operating conditions. This work can help provide and improve the understanding of how these membrane characteristics affect membrane performance for real NF processes.

  1. Shock tube investigation of dynamic response of pressure transducers for validation of rotor performance measurements

    Science.gov (United States)

    Bershader, Daniel

    1988-01-01

    For some time now, NASA has had a program under way to aid in the validation of rotor performance and acoustics codes associated with the UH-60 rotary-wing aircraft; and to correlate results of such studies with those obtained from investigations of other selected aircraft rotor performance. A central feature of these studies concerns the dynamic measurement of surface pressure at various locations up to frequencies of 25 KHz. For this purpose, fast-response gauges of the Kulite type are employed. The latter need to be buried in the rotor; they record surface pressures which are transmitted by a pipette connected to the gauge. The other end of the pipette is cut flush with the surface. In certain locations, the pipette configuration includes a rather sharp right-angle bend. The natural question has arisen in this connection: In what way are the pipettes modifying the signals received at the rotor surface and subsequently transmitted to the sensitive Kulite transducer element. The basic details and results of the program performed and recently completed in the High Pressure Shock Tube Laboratory of the Department of Aeronautics and Astronautics at Stanford University are given.

  2. Transient flow model and pressure dynamic features of tree-shaped fractal re- servoirs

    Institute of Scientific and Technical Information of China (English)

    TAN Xiao-hua; LI Xiao-ping

    2014-01-01

    A transient flow model of tree-shaped fractal reservoirs is built by embedding a fracture network simulated by a tree-shaped fractal network into a matrix system. The model can be solved using the Laplace conversion method. The dimensionless bottom hole pressure can be obtained using the Stehfest numerical inversion method. The bi-logarithmic type curves for the tree-shaped fractal reservoirs are thus obtained. The pressure transient responses under different fractal factors are discussed. The factors with a primary effect on the inter-porosity flow regime include the initial branch numberN, the length ratioα, and the branch angleθ. The diameter ratioβ has a significant effect on the fracture radial flow, the inter-porosity and the total system radial flow regimes. The total branch levelM of the network mainly influences the total system radial flow regime. The model presented in this paper provides a new methodology for analyzing and predicting the pressure dynamic characteristics of naturally fractured reservoirs.

  3. Peer pressure is a double-edged sword in vaccination dynamics

    Science.gov (United States)

    Wu, Zhi-Xi; Zhang, Hai-Feng

    2013-10-01

    Whether or not to change behavior depends not only on the personal success of each individual, but also on the success and/or behavior of others. Using this as motivation, we incorporate the impact of peer pressure into a susceptible-vaccinated-infected-recovered (SVIR) epidemiological model, where the propensity to adopt a particular vaccination strategy depends both on individual success as well as on the strategies of neighbors. We show that plugging into the peer pressure is a double-edged sword, which, on the one hand, strongly promotes vaccination when its cost is below a critical value, but, on the other hand, it can also strongly impede it if the critical value is exceeded. We explain this by revealing a facilitated cluster formation process that is induced by the peer pressure. Due to this, the vaccinated individuals are inclined to cluster together and therefore become unable to efficiently inhibit the spread of the infectious disease if the vaccination is costly. If vaccination is cheap, however, they reinforce each other in using it. Our results are robust to variations of the SVIR dynamics on different population structures.

  4. Nonequilibrium molecular dynamics simulation of pressure-driven water transport through modified CNT membranes.

    Science.gov (United States)

    Wang, Luying; Dumont, Randall S; Dickson, James M

    2013-03-28

    Nonequilibrium molecular dynamics (NEMD) simulations are presented to investigate the effect of water-membrane interactions on the transport properties of pressure-driven water flow passing through carbon nanotube (CNT) membranes. The CNT membrane is modified with different physical properties to alter the van der Waals interactions or the electrostatic interactions between water molecules and the CNT membranes. The unmodified and modified CNT membranes are models of simplified nanofiltration (NF) membranes at operating conditions consistent with real NF systems. All NEMD simulations are run with constant pressure difference (8.0 MPa) temperature (300 K), constant pore size (0.643 nm radius for CNT (12, 12)), and membrane thickness (6.0 nm). The water flow rate, density, and velocity (in flow direction) distributions are obtained by analyzing the NEMD simulation results to compare transport through the modified and unmodified CNT membranes. The pressure-driven water flow through CNT membranes is from 11 to 21 times faster than predicted by the Navier-Stokes equations. For water passing through the modified membrane with stronger van der Waals or electrostatic interactions, the fast flow is reduced giving lower flow rates and velocities. These investigations show the effect of water-CNT membrane interactions on water transport under NF operating conditions. This work can help provide and improve the understanding of how these membrane characteristics affect membrane performance for real NF processes.

  5. Analog modeling of pressurized subglacial water flow: Implications for tunnel valley formation and ice flow dynamics

    Science.gov (United States)

    Lelandais, Thomas; Ravier, Edouard; Mourgues, Régis; Pochat, Stéphane; Strzerzynski, Pierre; Bourgeois, Olivier

    2017-04-01

    Tunnel valleys are elongated and overdeepened depressions up to hundreds of kilometers long, several kilometers wide and hundreds of meters deep, found in formerly glaciated areas. These drainage features are interpreted as the result of subglacial meltwater erosion beneath ice sheets and constitute a major component of the subglacial drainage system. Although tunnel valleys have been described worldwide in the past decades, their formation is still a matter of debate. Here, we present an innovative experimental approach simulating pressurized water flow in a subglacial environment in order to study the erosional processes occurring at the ice-bed interface. We use a sandbox partially covered by a circular, viscous and transparent lid (silicon putty), simulating an impermeable ice cap. Punctual injection of pressurized water in the substratum at the center of the lid simulates meltwater production beneath the ice cap. Surface images collected by six synchronized cameras allow to monitor the evolution of the experiment through time, using photogrammetry methods and DEM generation. UV markers placed in the silicon are used to follow the silicon flow during the drainage of water at the substratum-lid interface, and give the unique opportunity to simultaneously follow the formation of tunnel valleys and the evolution of ice dynamics. When the water pressure is low, groundwater circulates within the substratum only and no drainage landforms appear at the lid-substratum interface. By contrast, when the water pressure exceeds a threshold that is larger than the sum of glaciostatic and lithostatic pressures, additional water circulation occurs at the lid-substratum interface and drainage landforms develop from the lid margin. These landforms share numerous morphological criteria with tunnel valleys such as undulating longitudinal profiles, U-shaped cross-sectional profiles with flat floors, constant widths and abrupt flanks. Continuous generation of DEMs and flow velocity

  6. Theory for planetary exospheres: I. Radiation pressure effect on dynamical trajectories

    Science.gov (United States)

    Beth, A.; Garnier, P.; Toublanc, D.; Dandouras, I.; Mazelle, C.

    2016-03-01

    The planetary exospheres are poorly known in their outer parts, since the neutral densities are low compared with the instruments detection capabilities. The exospheric models are thus often the main source of information at such high altitudes. We present a new way to take into account analytically the additional effect of the radiation pressure on planetary exospheres. In a series of papers, we present with an Hamiltonian approach the effect of the radiation pressure on dynamical trajectories, density profiles and escaping thermal flux. Our work is a generalisation of the study by Bishop and Chamberlain (Bishop, J., Chamberlian, J.W. [1989]. Icarus 81, 145-163). In this first paper, we present the complete solutions of particles trajectories, which are not conics, under the influence of the solar radiation pressure with some assumptions. This problem is similar to the classical Stark problem (Stark, J. [1914]. Ann. Phys. 348, 965-982). This problem was largely tackled in the literature and more specifically, recently by Lantoine and Russell (Lantoine, G., Russell, R.P. [2011]. Celest. Mech. Dynam. Astron. 109, 333-366) and by Biscani and Izzo (Biscani, F., Izzo, D. [2014]. Mon. Not. R. Astron. Soc. 439, 810-822) as we will discuss in this paper. We give here the full set of solutions for the motion of a particle (in our case for an atom or a molecule), i.e. the space coordinates and the time solution for bounded and unbounded trajectories in terms of Jacobi elliptic functions. We thus provide here the complete set of solutions for this so-call Stark effect (Stark, J. [1914]. Ann. Phys. 348, 965-982) in terms of Jacobi elliptic functions (Jacobi, C.G.J. [1829]. Fundamenta nova theoriae functionum ellipticarum. Sumtibus fratrum), which may be used to model the trajectories of particles in planetary exospheres.

  7. A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix B: Data base plots for SSME tests 901-290 through 901-414

    Science.gov (United States)

    Coffin, T.

    1986-01-01

    A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is described. The data base represents dynamic pressure measurements obtained during single engine hot firing tesets of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is also included to estimate spectral trends with SSME power level. Flow dynamic environments in high performance rocket engines are discussed.

  8. A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix C: Data base plots for SSME tests 902-214 through 902-314

    Science.gov (United States)

    Coffin, T.

    1986-01-01

    A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is reported. The data base represents dynamic pressure measurements obtained during single engine hot firing tests of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is included to estimate spectral trends with SSME power level. Flow Dynamic Environments in High Performance Rocket Engines are described.

  9. STUDY ON DYNAMIC STRESS INTENSITY FACTORS OF DISK WITH A RADIAL EDGE CRACK SUBJECTED TO EXTERNAL IMPULSIVE PRESSURE

    Institute of Scientific and Technical Information of China (English)

    Chen Aijun

    2007-01-01

    A dynamic weight function method is presented for dynamic stress intensity factors of circular disk with a radial edge crack under external impulsive pressure. The dynamic stresses in a circular disk are solved under abrupt step external pressure using the eigenfunction method.The solution consists of a quasi-static solution satisfying inhomogeneous boundary conditions and a dynamic solution satisfying homogeneous boundary conditions. By making use of FourierBessel series expansion, the history and distribution of dynamic stresses in the circular disk are derived. Furthermore, the equation for stress intensity factors under uniform pressure is used as the reference case, the weight function equation for the circular disk containing an edge crack is worked out, and the dynamic stress intensity factor equation for the circular disk containing a radial edge crack can be given. The results indicate that the stress intensity factors under sudden step external pressure vary periodically with time, and the ratio of the maximum value of dynamic stress intensity factors to the corresponding static value is about 2.0.

  10. Microdomain Ca{sup 2+} dynamics in mammalian muscle following prolonged high pressure treatments

    Energy Technology Data Exchange (ETDEWEB)

    Schnee, S; Schuermann, S; Fink, R [Medical Biophysics, Institute of Physiology and Pathophysiology, University of Heidelberg, INF326, 69120 Heidelberg (Germany); Ludwig, H [Physical Chemistry, Institute of Molecular Biotechnology and Biopharmacy, University of Heidelberg, INF 366 (Germany); Wegner, F von; Friedrich, O, E-mail: oliver.friedrich@physiologie.uni-heidelberg.de

    2008-07-15

    High pressure (HP) applications are an important thermodynamic tool to influence cellular processes. Especially processes that undergo large volume changes, e.g. opening or closing of ion channels, are in particular susceptible to HP treatments. Such volume changes are extremely difficult to assess for intracellular ion channels, like ryanodine receptors (RyR) residing in the membrane of organelles. In skeletal muscle, RyR act as Ca{sup 2+} release channels. We previously showed that plasmalemmal Na{sup +} and Ca{sup 2+} ion channels were irreversibly altered after prolonged 20 MPa treatments. Here, changes in microdomain Ca{sup 2+} levels due to elementary Ca{sup 2+} release events (ECRE) were monitored using confocal fluorescence microscopy. We studied ECRE in mammalian skeletal muscle following 3 h HP treatments up to 30 MPa to clarify whether RyR induced intracellular microdomain Ca{sup 2+} dynamics was more susceptible to HP treatment compared to surface membrane ion currents. ECRE frequencies exponentially declined with pressure. ECRE amplitudes and rise times (RT) were quite robust towards HP treatments. In contrast, spatial and temporal ECRE extension showed a tendency towards larger values up to 20 MPa but declined for higher pressures. Activation volumes for pressure-induced persistent ECRE alterations were zero for RT but showed a bimodal behavior for event duration. It seems that although ECRE frequencies are markedly reduced, ECRE morphology is less affected by HP. In particular, RyR opening time is practically unaltered and the observed morphological ECRE changes might reflect alterations in local Ca{sup 2+} buffers and Ca{sup 2+} concentration profiles rather than involvement of RyR in mammalian skeletal muscle.

  11. Dynamic high pressure measurements using a Fiber Bragg Grating probe and an arrayed waveguide grating spectrometer

    Science.gov (United States)

    Barbarin, Y.; Lefrançois, A.; Magne, S.; Woirin, K.; Sinatti, F.; Osmont, A.; Luc, J.

    2016-08-01

    High pressure shock profiles are monitored using a long Fiber Bragg Grating (FBG). Such thin probe, with a diameter of typically 150 μm, can be inserted directly into targets for shock plate experiments. The shocked FBG's portion is stressed under compression, which increases its optical group index and shortens its grating period. Placed along the 2D symmetrical axis of the cylindrical target, the second effect is stronger and the reflected spectrum shifts towards the shorter wavelengths. The dynamic evolution of FBG spectra is recorded with a customized Arrayed Waveguide Grating (AWG) spectrometer covering the C+L band. The AWG provides 40 channels of 200-GHz spacing with a special flattop design. The output channels are fiber-connected to photoreceivers (bandwidth: DC - 400 MHz or 10 kHz - 2 GHz). The experimental setup was a symmetric impact, completed in a 110-mm diameter single-stage gas gun with Aluminum (6061T6) impactors and targets. The FBG's central wavelength was 1605 nm to cover the pressure range of 0 - 8 GPa. The FBG was 50-mm long as well as the target's thickness. The 20-mm thick impactor maintains a shock within the target over a distance of 30 mm. For the impact at 522 m/s, the sustained pressure of 3.6 GPa, which resulted in a Bragg shift of (26.2 +/- 1.5) nm, is measured and retrieved with respectively thin-film gauges and the hydrodynamic code Ouranos. The shock sensitivity of the FBG is about 7 nm/GPa, but it decreases with the pressure level. The overall spectra evolution is in good agreement with the numerical simulations.

  12. Dynamic Compression Enhances Pressure-to-Pain Threshold in Elite Athlete Recovery: Exploratory Study.

    Science.gov (United States)

    Sands, William A; McNeal, Jeni R; Murray, Steven R; Stone, Michael H

    2015-05-01

    Athlete recovery-adaptation is crucial to the progress and performance of highly trained athletes. The purpose of this study was to assess peristaltic pulse dynamic compression (PPDC) in reducing short-term pressure-to-pain threshold (PPT) among Olympic Training Center athletes after morning training. Muscular tenderness and stiffness are common symptoms of fatigue and exercise-induced muscle microtrauma and edema. Twenty-four highly trained athletes (men = 12 and women = 12) volunteered to participate in this study. The athletes were randomly assigned to experimental (n = 12) and control (n = 12) groups. Pressure-to-pain threshold measurements were conducted with a manual algometer on 3 lower extremity muscles. Experimental group athletes underwent PPDC on both legs through computer-controlled circumferential inflated leggings that used a peristaltic-like pressure pattern from feet to groin. Pressures in each cell were set to factory defaults. Treatment time was 15 minutes. The control group performed the same procedures except that the inflation pump to the leggings was off. The experimental timeline included a morning training session, followed by a PPT pretest, treatment application (PPDC or control), an immediate post-test (PPT), and a delayed post-test (PPT) after the afternoon practice session. Difference score results showed that the experimental group's PPT threshold improved after PPDC treatment immediately and persisted the remainder of the day after afternoon practice. The control group showed no statistical change. We conclude that PPDC is a promising means of accelerating and enhancing recovery after the normal aggressive training that occurs in Olympic and aspiring Olympic athletes.

  13. Solar wind dynamic pressure and electric field as the main factors controlling Saturn's aurorae.

    Science.gov (United States)

    Crary, F J; Clarke, J T; Dougherty, M K; Hanlon, P G; Hansen, K C; Steinberg, J T; Barraclough, B L; Coates, A J; Gérard, J-C; Grodent, D; Kurth, W S; Mitchell, D G; Rymer, A M; Young, D T

    2005-02-17

    The interaction of the solar wind with Earth's magnetosphere gives rise to the bright polar aurorae and to geomagnetic storms, but the relation between the solar wind and the dynamics of the outer planets' magnetospheres is poorly understood. Jupiter's magnetospheric dynamics and aurorae are dominated by processes internal to the jovian system, whereas Saturn's magnetosphere has generally been considered to have both internal and solar-wind-driven processes. This hypothesis, however, is tentative because of limited simultaneous solar wind and magnetospheric measurements. Here we report solar wind measurements, immediately upstream of Saturn, over a one-month period. When combined with simultaneous ultraviolet imaging we find that, unlike Jupiter, Saturn's aurorae respond strongly to solar wind conditions. But in contrast to Earth, the main controlling factor appears to be solar wind dynamic pressure and electric field, with the orientation of the interplanetary magnetic field playing a much more limited role. Saturn's magnetosphere is, therefore, strongly driven by the solar wind, but the solar wind conditions that drive it differ from those that drive the Earth's magnetosphere.

  14. Probabilistic modelling of the high-pressure arc cathode spot displacement dynamic

    CERN Document Server

    Coulombe, S

    2003-01-01

    A probabilistic modelling approach for the study of the cathode spot displacement dynamic in high-pressure arc systems is developed in an attempt to interpret the observed voltage fluctuations. The general framework of the model allows to define simple, probabilistic displacement rules, the so-called cathode spot dynamic rules, for various possible surface states (un-arced metal, arced, contaminated) and to study the resulting dynamic of the cathode spot displacements over one or several arc passages. The displacements of the type-A cathode spot (macro-spot) in a magnetically rotating arc using concentric electrodes made up of either clean or contaminated metal surfaces is considered. Experimental observations for this system revealed a 1/f sup - sup t sup i sup l sup d sup e sup 1 signature in the frequency power spectrum (FPS) of the arc voltage for anchoring arc conditions on the cathode (e.g. clean metal surface), while it shows a 'white noise' signature for conditions favouring a smooth movement (e.g. ox...

  15. Dynamic modeling and explicit/multi-parametric MPC control of pressure swing adsorption systems

    KAUST Repository

    Khajuria, Harish

    2011-01-01

    Pressure swing adsorption (PSA) is a flexible, albeit complex gas separation system. Due to its inherent nonlinear nature and discontinuous operation, the design of a model based PSA controller, especially with varying operating conditions, is a challenging task. This work focuses on the design of an explicit/multi-parametric model predictive controller for a PSA system. Based on a system involving four adsorbent beds separating 70% H2, 30% CH4 mixture into high purity hydrogen, the key controller objective is to fast track H2 purity to a set point value of 99.99%. To perform this task, a rigorous and systematic framework is employed. First, a high fidelity detailed dynamic model is built to represent the system\\'s real operation, and understand its dynamic behavior. The model is then used to derive appropriate linear models by applying suitable system identification techniques. For the reduced models, a model predictive control (MPC) step is formulated, where latest developments in multi-parametric programming and control are applied to derive a novel explicit MPC controller. To test the performance of the designed controller, closed loop simulations are performed where the dynamic model is used as the virtual plant. Comparison studies of the derived explicit MPC controller are also performed with conventional PID controllers. © 2010 Elsevier Ltd. All rights reserved.

  16. Circulatory effects of expiratory flow-limited exercise, dynamic hyperinflation and expiratory muscle pressure

    Directory of Open Access Journals (Sweden)

    P. T. Macklem

    2006-12-01

    Full Text Available This article reviews recent research in normal subjects exercising with and without expiratory flow limitation at 1 L·s–1 imposed by a Starling resistor in the expiratory line, and in patients with chronic obstructive pulmonary disease (COPD, using optoelectronic plethysmography to measure respiratory kinematics, combined with mouth, pleural and abdominal pressure measurements, to assess work of breathing and respiratory muscle performance. In normal subjects, flow-limited exercise resulted in the following: 1 Impaired exercise performance due to intolerable dyspnoea; 2 hypercapnia; 3 excessive respiratory muscle recruitment; 4 blood shifts from trunk to extremities; 5 a 10% reduction in cardiac output and a 5% reduction in arterial oxygen saturation, decreasing energy supplies to working respiratory and locomotor muscles. In both normal subjects and in COPD patients, dynamic hyperinflation did not always occur. Those patients that hyperinflated had worse lung function and less work of breathing, but better exercise performance than the others, in whom expiratory muscle recruitment prevented dynamic hyperinflation at the cost of increased work of breathing and excessive oxygen cost of breathing. This established an early competition between respiratory and locomotor muscles for available energy supplies. Dynamic hyperinflation is a better exercise strategy in chronic obstructive pulmonary disease than expiratory muscle recruitment, but the benefit it confers is small.

  17. Effects of a solar wind dynamic pressure increase in the magnetosphere and in the ionosphere

    Directory of Open Access Journals (Sweden)

    L. Juusola

    2010-10-01

    Full Text Available On 17 July 2005, an earthward bound north-south oriented magnetic cloud and its sheath were observed by the ACE, SoHO, and Wind solar wind monitors. A steplike increase of the solar wind dynamic pressure during northward interplanetary magnetic field conditions was related to the leading edge of the sheath. A timing analysis between the three spacecraft revealed that this front was not aligned with the GSE y-axis, but had a normal (−0.58,0.82,0. Hence, the first contact with the magnetosphere occurred on the dawnside rather than at the subsolar point. Fortunately, Cluster, Double Star 1, and Geotail happened to be distributed close to the magnetopause in this region, which made it possible to closely monitor the motion of the magnetopause. After the pressure front had impacted the magnetosphere, the magnetopause was perceived first to move inward and then immediately to correct the overshoot by slightly expanding again such that it ended up between the Cluster constellation with Double Star 1 inside the magnetosphere and Geotail in the magnetosheath. Coinciding with the inward and subsequent outward motion, the ground-based magnetic field at low latitudes was observed to first strengthen and then weaken. As the magnetopause position stabilised, so did the ground-based magnetic field intensity, settling at a level slightly higher than before the pressure increase. Altogether the magnetopause was moving for about 15 min after its first contact with the front. The high latitude ionospheric signature consisted of two parts: a shorter (few minutes and less intense preliminary part comprised a decrease of AL and a negative variation of PC. A longer (about ten minutes and more intense main part of the signature comprised an increase of AU and a positive variation of PC. Measurements from several ground-based magnetometer networks (210 MM CPMN, CANMOS, CARISMA, GIMA, IMAGE, MACCS, SuperMAG, THEMIS, TGO were used to obtain information on the

  18. Effect of temperature, pressure, and cosolvents on structural and dynamic properties of the hydration shell of SNase: a molecular dynamics computer simulation study.

    Science.gov (United States)

    Smolin, Nikolai; Winter, Roland

    2008-01-24

    It is now generally agreed that the hydration water and solvational properties play a crucial role in determining the dynamics and hence the functionality of proteins. We present molecular dynamics computer simulation studies on staphylococcal nuclease (SNase) at various temperatures and pressures as well as in different cosolvent solutions containing various concentrations of urea and glycerol. The aim is to provide a molecular level understanding of how different types of cosolvents (chaotropic and kosmotropic) as well as temperature and high hydrostatic pressure modify the structure and dynamics of the hydration water. Taken together, these three intrinsic thermodynamic variables, temperature, pressure, and chemical potential (or activity) of the solvent, are able to influence the stability and function of the protein by protein-solvent dynamic coupling in different ways. A detailed analysis of the structural and dynamical properties of the water and cosolvents at the protein surface (density profile, coordination numbers, hydrogen-bond distribution, average H-bond lifetimes (water-protein and water-water), and average residence time of water in the hydration shell) was carried out, and differences in the structural and dynamical properties of the hydration water in the presence of the different cosolvents and at temperatures between 300 and 400 K and pressures up to 5000 bar are discussed. Furthermore, the results obtained help understand various thermodynamic properties measured for the protein.

  19. On the impact of radiation pressure on the dynamics and inner structure of dusty wind-driven shells

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-González, Sergio; Silich, Sergiy; Tenorio-Tagle, Guillermo, E-mail: silich@inaoep.mx [Instituto Nacional de Astrofísica Óptica y Electrónica, AP 51, 72000 Puebla (Mexico)

    2014-04-20

    Massive young stellar clusters are strong sources of radiation and mechanical energy. Their powerful winds and radiation pressure sweep up interstellar gas into thin expanding shells that trap the ionizing radiation produced by the central clusters affecting the dynamics and the distribution of their ionized gas. Here we continue our comparison of the star cluster winds and radiation pressure effects on the dynamics of shells around young massive clusters. We calculate the impact that radiation pressure has on the distribution of matter and thermal pressure within such shells, as well as on the density-weighted ionization parameter U{sub w} , and put our results on the diagnostic diagram, which allows one to discriminate between the wind-dominated and radiation-dominated regimes. We found that model-predicted values of the ionization parameter agree well with typical values found in local starburst galaxies. Radiation pressure may affect the inner structure and the dynamics of wind-driven shells, but only during the earliest stages of evolution (before ∼3 Myr) or if a major fraction of the star cluster mechanical luminosity is dissipated or radiated away within the star cluster volume and thus the star cluster mechanical energy output is significantly smaller than star cluster synthetic models predict. However, even in these cases radiation dominates over the wind dynamical pressure only if the exciting cluster is embedded into a high-density ambient medium.

  20. Analysis on Design Dynamic Pressure Chamber and Static Pressure Chamber Integration Wind Pressure Chamber of Spray Paint Room%喷漆室动压室及静压室整合风压室的设计浅析

    Institute of Scientific and Technical Information of China (English)

    贺大军

    2012-01-01

    简要介绍了动压室和静压室合一的喷漆室的缺点以及设计和施工中的处理方法和其使用场合。%The shortcomings, design and the construction of the processing method and its application occasion of dynamic pressure chamber and static pressure chamber syncretic spray paint room were briefly introduced.

  1. Dynamics of pollutant indicators during flood events in a small river under strong anthropogenic pressures

    Science.gov (United States)

    Brion, Natacha; Carbonnel, Vincent; Elskens, Marc; Claeys, Philippe; Verbanck, Michel A.

    2017-04-01

    In densely populated regions, human activities profoundly modify natural water circulation as well as water quality, with increased hydrological risks (floods, droughts,…) and chemical hazards (untreated sewage releases, industrial pollution,…) as consequence. In order to assess water and pollutants dynamics and their mass-balance in strongly modified river system, it is important to take into account high flow events as a significant fraction of water and pollutants loads may occur during these short events which are generally underrepresented in classical mass balance studies. A good example of strongly modified river systems is the Zenne river in and around the city of Brussels (Belgium).The Zenne River (Belgium) is a rather small but dynamic rain fed river (about 10 m3/s in average) that is under the influence of strong contrasting anthropogenic pressures along its stretch. While the upstream part of its basin is rather characterized by agricultural land-use, urban and industrial areas dominate the downstream part. In particular, the city of Brussels (1.1M inhabitants) discharges in the Zenne River amounts of wastewater that are large compared to the natural riverine flow. In order to assess water and pollutants dynamics and their mass-balance in the Zenne hydrographic network, we followed water flows and concentrations of several water quality tracers during several flood episodes with an hourly frequency and at different locations along the stretch of the River. These parameters were chosen as indicators of a whole range of pollutions and anthropogenic activities. Knowledge of the high-frequency pollutants dynamics during floods is required for establishing accurate mass-balances of these elements. We thus report here the dynamics of selected parameters during entire flood events, from the baseline to the decreasing phase and at hourly frequency. Dynamics at contrasting locations, in agricultural or urban environments are compared. In particular, the

  2. Glycation promoted by dynamic high pressure microfluidisation pretreatment revealed by high resolution mass spectrometry.

    Science.gov (United States)

    Huang, Xiaoqin; Tu, Zongcai; Wang, Hui; Zhang, Qiuting; Hu, Yueming; Zhang, Lan; Niu, Peipei; Shi, Yan; Xiao, Hui

    2013-12-01

    The effect of dynamic high pressure microfluidisation (DHPM) pretreatment on the glycation of bovine serum albumin (BSA) was investigated. A detailed glycation map was obtained from high resolution mass spectrometry. Without DHPM pretreatment, only 7 glycation sites were identified, whereas the numbers were increased to 10, 11 and 11 when BSA-glucose was pretreated with DHPM at 50, 100 and 200 MPa, respectively, suggesting that DHPM pretreatment can significantly promote the Maillard reaction. Average degree of substitution per peptide molecule BSA (DSP) was used to further evaluate the glycation level under various DHPM conditions. All the DHPM pretreated samples exhibited elevated glycation level compared to the un-pretreated sample. With 100 MPa DHPM pretreatment, the protein showed the most significantly enhanced glycation extent. In addition, our results suggest that Maillard-type glycation followed by mass spectrometry analysis can be used to study the conformational changes when proteins are disturbed by external forces.

  3. Dynamic property evaluation of aluminum alloy 2519A by split Hopkinson pressure bar

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xin-ming; LI Hui-jie; LI Hui-zhong; GAO Hui; GAO Zhi-guo; LIU Ying; LIU Bo

    2008-01-01

    Impact behavior of aluminum alloy 2519A was investigated at strain rates of 600-7 000 s-1 and temperatures of 20-450 ℃ by a split Hopkinson pressure bar. The results show that the flow stress is dominated by temperature, and it increases with strain rate and decreases with deformation temperature. The serrated flow curves show the dynamic recrystallization occurs. The strain rate sensitivity exponents m determined are 0.066, 0.059 4, 0.059 0 and 0.057 3 at 20, 150, 300 and 450 ℃, respectively. Cowper- Symonds constitutive equation expressing the plastic flow behavior was calculated by analysis and regression of the experimental results. The fracture characteristics under the experimental conditions were observed by optical microscopy(OM) and scanning electron microscopy(SEM). It is determined that the tested material fails as a result of adiabatic shearing.

  4. Dynamics of cathode spots in low-pressure arc plasma removing oxide layer on steel surfaces

    Science.gov (United States)

    Tang, Z. L.; Yang, K.; Liu, H. X.; Zhang, Y. C.; Li, H.; Zhu, X. D.

    2016-03-01

    The dynamics of cathode spots has been investigated in low-pressure arc plasma for removing oxide layer on low carbon steel surfaces. The motion of cathode spots was observed with a high speed camera, and the arc voltage was analyzed by fast Fourier transform. The spots move on clean steel surface as a random walk, and the low-frequency components dominated the voltage waveform. However, the spots on steel surfaces with oxide layer tend to burn on the rim of the eroded area formed in the previous arcing, and the low-frequency components decrease correspondingly. The "color" of the colored random noise for arc voltage varies from the approximate brown noise for clean steel surface to pink noise for thick oxide layer, where the edge effect of boundary is considered to play a significant role.

  5. Dynamic neck development in a polymer tube under internal pressure loading

    DEFF Research Database (Denmark)

    Lindgreen, Britta; Tvergaard, Viggo; Needleman, Alan

    2008-01-01

    and a short wave length imperfection. After some thinning down at the necks, the mode of deformation switches to neck propagation along the circumference of the tube. A case is shown in which the necks have propagated along the entire tube wall, so that network locking in the polymer results in high stiffness......The initiation and growth of necks in polymer tubes subjected to rapidly increasing internal pressure is analyzed numerically. Plane strain conditions are assumed to prevail in the axial direction. The polymer is characterized by a finite strain elastic-viscoplastic constitutive relation...... and the calculations are carried out using a dynamic finite element program. Numerical results for neck development are illustrated and discussed for tubes of various thicknesses. The sensitivity to the wave number of the thickness imperfections is studied with a focus on comparing a long wave length imperfection...

  6. A regularized model for impact in explicit dynamics applied to the split Hopkinson pressure bar

    Science.gov (United States)

    Otto, Peter; De Lorenzis, Laura; Unger, Jörg F.

    2016-10-01

    In the numerical simulation of impact phenomena, artificial oscillations can occur due to an instantaneous change of velocity in the contact area. In this paper, a nonlinear penalty regularization is used to avoid these oscillations. A particular focus is the investigation of higher order methods in space and time to increase the computational efficiency. The spatial discretization is realized by higher order spectral element methods that are characterized by a diagonal mass matrix. The time integration scheme is based on half-explicit Runge-Kutta scheme of fourth order. For the conditionally stable scheme, the critical time step is influenced by the penalty regularization. A framework is presented to adjust the penalty stiffness and the time step for a specific mesh to avoid oscillations. The methods presented in this paper are applied to 1D-simulations of a split Hopkinson pressure bar, which is commonly used for the investigation of materials under dynamic loading.

  7. An analysis of the cerebrospinal fluid dynamics in patients with normal pressure hydrocephalus

    Energy Technology Data Exchange (ETDEWEB)

    Mabe, Hideo; Nagai, Hajime (Nagoya City Univ. (Japan). Faculty of Medicine); Banno, Tatsuo

    1994-07-01

    Using a cine mode technique and a gradient-echo magnetic resonance (MR) sequencing, the MR signal intensity of the aqueduct has been evaluated in twelve patients suspected of normal pressure hydrocephalus (NPH). In patients with a substantial cerebrospinal fluid (CSF) circulation disturbance in the subarachnoid space, marked changes in the signal intensity of the aqueduct were seen during heart cycles, whereas in patients with less of a CSF circulation disturbance, changes in the signal intensity of the aqueduct were not as marked. Further, all patients manifesting marked changes in the signal intensity of the aqueduct showed a clinical improvement in their symptoms after undergoing a shunt. These results suggest that cine-mode MRI is useful for assessing the CSF dynamics and may be helpful in selecting patients who would benefit from shunt therapy. (author).

  8. Phase Synchronization of Pressure-Flow Fluctuations: A measure of cerebral autoregulation dynamics

    CERN Document Server

    Chen, Z; Ivanov, P C; Novák, V; Stanley, H E

    2006-01-01

    We employ a synchronization method to investigate the relationship between the blood flow velocities (BFV) in the middle cerebral arteries (MCA) and beat-to-beat blood pressure (BP) recorded from a finger in healthy and post-stroke subjects during four different physiologic conditions: supine, head-up tilt, hyperventilation and CO$_2$ rebreathing in upright position. To evaluate whether instantaneous BP changes are synchronized with changes in the BFV, we compare dynamical patterns in the instantaneous phases of these signals, obtained from the Hilbert transform, as a function of time. We find that in post-stroke subjects the instantaneous phase increments of BP and BFV exhibit well pronounced patterns that remain stable in time for all four physiologic conditions, while in healthy subjects these patterns are different, less pronounced and more variable. Further, we show that the instantaneous phase increments of BP and BFV are cross-correlated even within a single heartbeat cycle. The maximum correlation str...

  9. Argon metastable dynamics in a filamentary jet micro-discharge at atmospheric pressure

    CERN Document Server

    Niermann, B; Kuschel, T; Benedikt, J; Böke, M; Winter, J

    2011-01-01

    Space and time resolved concentrations of Ar ($^{3}P_2$) metastable atoms at the exit of an atmospheric pressure radio-frequency micro-plasma jet were measured using tunable diode laser absorption spectroscopy. The discharge features a coaxial geometry with a hollow capillary as an inner electrode and a ceramic tube with metal ring as outer electrode. Absorption profiles of metastable atoms as well as optical emission measurements reveal the dynamics and the filamentary structure of the discharge. The average spatial distribution of Ar metastables is characterized with and without a target in front of the jet, showing that the target potential and therewith the electric field distribution substantially changes the filaments' expansion. Together with the detailed analysis of the ignition phase and the discharge's behavior under pulsed operation, the results give an insight into the excitation and de-excitation mechanisms.

  10. Dipolar Relaxation Dynamics at the Active Site of an ATPase Regulated by Membrane Lateral Pressure.

    Science.gov (United States)

    Fischermeier, Elisabeth; Pospíšil, Petr; Sayed, Ahmed; Hof, Martin; Solioz, Marc; Fahmy, Karim

    2017-01-24

    The active transport of ions across biological membranes requires their hydration shell to interact with the interior of membrane proteins. However, the influence of the external lipid phase on internal dielectric dynamics is hard to access by experiment. Using the octahelical transmembrane architecture of the copper-transporting P1B -type ATPase from Legionella pneumophila as a model structure, we have established the site-specific labeling of internal cysteines with a polarity-sensitive fluorophore. This enabled dipolar relaxation studies in a solubilized form of the protein and in its lipid-embedded state in nanodiscs. Time-dependent fluorescence shifts revealed the site-specific hydration and dipole mobility around the conserved ion-binding motif. The spatial distribution of both features is shaped significantly and independently of each other by membrane lateral pressure. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Theoretical study of dynamics of arterial wall remodeling in response to changes in blood pressure.

    Science.gov (United States)

    Rachev, A; Stergiopulos, N; Meister, J J

    1996-05-01

    The dynamics of arterial wall remodeling was studied on the basis of a phenomenological mathematical model. Sustained hypertension was simulated by a step increase in blood pressure. Remodeling rate equations were postulated for the evolution of the geometrical dimensions that characterize the zero stress state of the artery. The driving stimuli are the deviations of the extreme values of the circumferential stretch ratios and the average stress from their values at the normotensive state. Arterial wall was considered to be a thick-walled tube made of nonlinear elastic incompressible material. Results showed that thickness increases montonically with time whereas the opening angle exhibits a biphasic pattern. Geometric characteristics reach asymptotically a new homeostatic steady state, in which the stress and strain distribution is practically identical with the distribution under normotensive conditions. The model predictions are in good agreement with published experimental findings.

  12. Fluid front displacement dynamics affecting pressure fluctuations and phase entrapment in porous media

    Science.gov (United States)

    Moebius, F.; Or, D.

    2012-04-01

    Many natural and engineering processes involve motion of fluid fronts in porous media, from infiltration and drainage in hydrology to reservoir management in petroleum engineering. Macroscopically smooth and continuous motion of displacement fronts involves numerous rapid interfacial jumps and local reconfigurations. Detailed observations of displacement processes in micromodels illustrate the wide array of fluid interfacial dynamics ranging from irregular jumping-pinning motions to gradual pore scale invasions. The pressure fluctuations associated with interfacial motions reflect not only pore geometry (as traditionally hypothesized) but there is a strong influence of boundary conditions (e.g., mean drainage rate). The time scales associated with waiting time distribution of individual invasion events and decay time of inertial oscillations (following a rapid interfacial jump) provide a means for distinguishing between displacement regimes. Direct observations using high-speed camera combined with concurrent pressure signal measurements were instrumental in clarifying influences of flow rates, pore size, and gravity on burst size distribution and waiting times. We compared our results with the early experimental and theoretical study on burst size and waiting time distribution during slow drainage processes of Måløy et al. [Måløy et al., 1992]. Results provide insights on critical invasion events that exert strong influence on macroscopic phenomena such as front morphology and residual phase entrapment behind leading to hysteresis. Måløy, K. J., L. Furuberg, J. Feder, and T. Jossang (1992), Dynamics of Slow Drainage in Porous-Media, Phys Rev Lett, 68(14), 2161-2164.

  13. Effects of the van der Waals Force on the Dynamics Performance for a Micro Resonant Pressure Sensor

    Directory of Open Access Journals (Sweden)

    Lizhong Xu

    2016-01-01

    Full Text Available The micro resonant pressure sensor outputs the frequency signals where the distortion does not take place in a long distance transmission. As the dimensions of the sensor decrease, the effects of the van der Waals forces should be considered. Here, a coupled dynamic model of the micro resonant pressure sensor is proposed and its coupled dynamic equation is given in which the van der Waals force is considered. By the equation, the effects of the van der Waals force on the natural frequencies and vibration amplitudes of the micro resonant pressure sensor are investigated. Results show that the natural frequency and the vibrating amplitudes of the micro resonant pressure sensor are affected significantly by van der Waals force for a small clearance between the film and the base plate, a small initial tension stress of the film, and some other conditions.

  14. Quantum molecular dynamics simulations of uranium at high pressure and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Hood, R Q; Yang, L H; Moriarty, J A

    2008-01-22

    Constant-volume quantum molecular dynamics (QMD) simulations of uranium (U) have been carried out over a range of pressures and temperatures that span the experimentally observed solid orthorhombic {alpha}-U, body-centered cubic (bcc), and liquid phases, using an ab initio plane-wave pseudopotential method within the generalized gradient approximation of density functional theory. A robust U pseudopotential has been constructed for these simulations that treats the 14 valence and outer-core electrons per atom necessary to calculate accurate structural and thermodynamic properties up to 100 GPa. Its validity has been checked by comparing low-temperature results with experimental data and all-electron full-potential linear-muffin-tin-orbital calculations of several different uranium solid structures. Calculated QMD energies and pressures for the equation of state of uranium in the solid and liquid phases are given, along with results for the Grueneisen parameter and the specific heat. We also present results for the radial distribution function, bond-angle distribution function, electronic density of states, and liquid diffusion coefficient, as well as evidence for short-range order in the liquid.

  15. Transonic Dynamics Tunnel Force and Pressure Data Acquired on the HSR Rigid Semispan Model

    Science.gov (United States)

    Schuster, David M.; Rausch, Russ D.

    1999-01-01

    This report describes the aerodynamic data acquired on the High Speed Research Rigid Semispan Model (HSR-RSM) during NASA Langley Transonic Dynamics Tunnel (TDT) Test 520 conducted from 18 March to 4 April, 1996. The purpose of this test was to assess the aerodynamic character of a rigid high speed civil transport wing. The wing was fitted with a single trailing edge control surface which was both steadily deflected and oscillated during the test to investigate the response of the aerodynamic data to steady and unsteady control motion. Angle-of-attack and control surface deflection polars at subsonic, transonic and low-supersonic Mach numbers were obtained in the tunnel?s heavy gas configuration. Unsteady pressure and steady loads data were acquired on the wing, while steady pressures were measured on the fuselage. These data were reduced using a variety of methods, programs and computer systems. The reduced data was ultimately compiled onto a CD-ROM volume which was distributed to HSR industry team members in July, 1996. This report documents the methods used to acquire and reduce the data, and provides an assessment of the quality, repeatability, and overall character of the aerodynamic data measured during this test.

  16. Influence of dynamic pressure on deep underground soft rock roadway support and its application

    Institute of Scientific and Technical Information of China (English)

    Meng Qingbin; Han Lijun; Chen Yanlong; Fan Jiadong; Wen Shengyong; Yu Liyuan; Li Hao

    2016-01-01

    Due to high ground stress and mining disturbance, the deformation and failure of deep soft rock roadway is serious, and invalidation of the anchor net-anchor cable supporting structure occurs. The failure char-acteristics of roadways revealed with the help of the ground pressure monitoring. Theoretical analysis was adopted to analyze the influence of mining disturbance on stress distribution in surrounding rock, and the change of stress was also calculated. Considering the change of stress in surrounding rock of bot-tom extraction roadway, the displacement, plastic zone and distribution law of principal stress difference under different support schemes were studied by means of FLAC3D. The supporting scheme of U-shaped steel was proposed for bottom extraction roadway that underwent mining disturbance. We carried out a similarity model test to verify the effect of support in dynamic pressure. Monitoring results demonstrated the change rules of deformation and stress of surrounding rock in different supporting schemes. The supporting scheme of U-shaped steel had an effective control on deformation of surrounding rock. The scheme was successfully applied in underground engineering practice, and achieved good technical and economic benefits.

  17. Dynamics and Conservation Management of a Wooded Landscape under High Herbivore Pressure

    Directory of Open Access Journals (Sweden)

    Adrian C. Newton

    2013-01-01

    Full Text Available We present the use of a spatially explicit model of woodland dynamics (LANDIS-II to examine the impacts of herbivory in the New Forest National Park, UK, in relation to its management for biodiversity conservation. The model was parameterized using spatial data and the results of two field surveys and then was tested with results from a third survey. Field survey results indicated that regeneration by tree species was found to be widespread but to occur at low density, despite heavy browsing pressure. The model was found to accurately predict the abundance and richness of tree species. Over the duration of the simulations (300 yr, woodland area increased in all scenarios, with or without herbivory. While the increase in woodland area was most pronounced under a scenario of no herbivory, values increased by more than 70% even in the presence of heavy browsing pressure. Model projections provided little evidence for the conversion of woodland areas to either grassland or heathland; changes in woodland structure and composition were consistent with traditional successional theory. These results highlight the need for multiple types of intervention when managing successional landscape mosaics and demonstrate the value of landscape-scale modelling for evaluating the role of herbivory in conservation management.

  18. STRONG SOLAR WIND DYNAMIC PRESSURE PULSES: INTERPLANETARY SOURCES AND THEIR IMPACTS ON GEOSYNCHRONOUS MAGNETIC FIELDS

    Energy Technology Data Exchange (ETDEWEB)

    Zuo, Pingbing; Feng, Xueshang; Wang, Yi [SIGMA Weather Group, State Key Laboratory of Space Weather, National Space Science Center, Chinese Academy of Sciences, Beijing (China); Xie, Yanqiong [College of Meteorology and Oceanography, PLA University of Science and Technology, Nanjing (China); Xu, Xiaojun, E-mail: pbzuo@spaceweather.ac.cn, E-mail: fengx@spaceweather.ac.cn [Space Science Institute, Macau University of Science and Technology, Macao (China)

    2015-10-20

    In this investigation, we first present a statistical result of the interplanetary sources of very strong solar wind dynamic pressure pulses (DPPs) detected by WIND during solar cycle 23. It is found that the vast majority of strong DPPs reside within solar wind disturbances. Although the variabilities of geosynchronous magnetic fields (GMFs) due to the impact of positive DPPs have been well established, there appears to be no systematic investigations on the response of GMFs to negative DPPs. Here, we study both the decompression effects of very strong negative DPPs and the compression from strong positive DPPs on GMFs at different magnetic local time sectors. In response to the decompression of strong negative DPPs, GMFs on the dayside near dawn and near dusk on the nightside, are generally depressed. But near the midnight region, the responses of GMF are very diverse, being either positive or negative. For part of the events when GOES is located at the midnight sector, the GMF is found to abnormally increase as the result of magnetospheric decompression caused by negative DPPs. It is known that under certain conditions magnetic depression of nightside GMFs can be caused by the impact of positive DPPs. Here, we find that a stronger pressure enhancement may have a higher probability of producing the exceptional depression of GMF at the midnight region. Statistically, both the decompression effect of strong negative DPPs and the compression effect of strong positive DPPs depend on the magnetic local time, which are stronger at the noon sector.

  19. Static and dynamic tensile behaviour of aluminium processed by high pressure torsion

    Directory of Open Access Journals (Sweden)

    Verleysen Patricia

    2015-01-01

    Full Text Available High pressure torsion (HPT is a severe plastic deformation technique in which a small, disk-like sample is subjected to a torsional deformation under a high hydrostatic pressure. In present study, the static and dynamic tensile behaviour of commercially pure aluminium (99.6 wt% processed by HPT is studied. The high strain rate tensile behaviour is characterized using a purpose-developed miniature split Hopkinson tensile bar setup by which strain rates up to 5 × 103 s−1 can be reached. During the tests, the deformation of a speckle pattern applied to the samples is recorded, by which local information on the strain is obtained using a digital image correlation technique. Electron back scatter diffraction images are used to investigate the microstructural evolution, more specifically the grain refinement obtained by HPT. The fracture surfaces of the tensile samples are studied by scanning electron microscopy. Results show that the imposed severe plastic deformation significantly increases the tensile strength, however, at the expense of ductility. The strain rate only has a minor influence on the materials tensile behaviour.

  20. The Effects of Magnetic Fields on the Dynamics of Radiation Pressure-dominated Massive Star Envelopes

    Science.gov (United States)

    Jiang, Yan-Fei; Cantiello, Matteo; Bildsten, Lars; Quataert, Eliot; Blaes, Omer

    2017-07-01

    We use three-dimensional radiation magnetohydrodynamic simulations to study the effects of magnetic fields on the energy transport and structure of radiation pressure-dominated main sequence massive star envelopes at the region of the iron opacity peak. We focus on the regime where the local thermal timescale is shorter than the dynamical timescale, corresponding to inefficient convective energy transport. We begin with initially weak magnetic fields relative to the thermal pressure, from 100 to 1000 G in differing geometries. The unstable density inversion amplifies the magnetic field, increasing the magnetic energy density to values close to equipartition with the turbulent kinetic energy density. By providing pressure support, the magnetic field’s presence significantly increases the density fluctuations in the turbulent envelope, thereby enhancing the radiative energy transport by allowing photons to diffuse out through low-density regions. Magnetic buoyancy brings small-scale magnetic fields to the photosphere and increases the vertical energy transport, with the energy advection velocity proportional to the Alfvén velocity, although in all cases we study, photon diffusion still dominates the energy transport. The increased radiative and advective energy transport causes the stellar envelope to shrink by several scale heights. We also find larger turbulent velocity fluctuations compared with the purely hydrodynamic case, reaching ≈ 100 {{{km}}{{s}}}-1 at the stellar photosphere. The photosphere also shows vertical oscillations with similar averaged velocities and periods of a few hours. The increased turbulent velocity and oscillations will have strong impacts on the line broadening and periodic signals in massive stars.

  1. Development of a new type of high pressure calorimetric cell, mechanically agitated and equipped with a dynamic pressure control system: Application to the characterization of gas hydrates

    Energy Technology Data Exchange (ETDEWEB)

    Plantier, F., E-mail: frederic.plantier@univ-pau.fr; Missima, D.; Torré, J.-P. [Univ Pau and Pays Adour, CNRS, TOTAL - UMR 5150 – LFC-R - Laboratoire des Fluides Complexes et leurs Réservoirs, BP 1155 – PAU, F-64013 (France); Marlin, L. [Univ Pau and Pays Adour, IPRA FR2952 - Fédération de Recherche- Atelier de Physique Générale, BP 1155 – PAU, F-64013 (France)

    2013-12-15

    A novel prototype of calorimetric cell has been developed allowing experiments under pressure with an in situ agitation system and a dynamic control of the pressure inside the cell. The use of such a system opens a wide range of potential practical applications for determining properties of complex fluids in both pressurized and agitated conditions. The technical details of this prototype and its calibration procedure are described, and an application devoted to the determination of phase equilibrium and phase change enthalpy of gas hydrates is presented. Our results, obtained with a good precision and reproducibility, were found in fairly good agreement with those found in literature, illustrate the various interests to use this novel apparatus.

  2. Prediction of Stress Concentration effect under Thermal and Dynamic loads on a High Pressure Turbine Rotor

    Directory of Open Access Journals (Sweden)

    R.Nagendra Babu

    2010-08-01

    Full Text Available Geometric discontinuities cause a large variation of stress and produce a significant increase in stress. The high stress due to the variation of geometry is called as ‘stress concentration’. This will increase when the loads are further applied. There are many investigators who have studied the stress distribution around the notches, grooves, and other irregularities of various machine components. This paper analyses the effects of thermal and fatigue load on a steam turbine rotor under the operating conditions. Stresses due to thermal and dynamic loads of High Pressure Steam Turbine Rotor of 210MW power station are found in two stages. A source code is developed for calculating the nominal stress at each section of HPT rotor. Maximum stress is obtained using FEA at the corresponding section. Thermal and Fatigue Stress Concentration Factors at each section are calculated. It is observed that the SCFdue to the combined effect of thermal and dynamic loads at the temperatures beyond 5400C is exceeding the safe limits.

  3. Van Allen Probes observations of EMIC events triggered by solar wind dynamic pressure enhancements

    Science.gov (United States)

    Lee, D. Y.; Cho, J.; Roh, S. J.; Shin, D. K.; Hwang, J.; Kim, K. C.; Choi, C.; Kletzing, C.; Wygant, J. R.; Thaller, S. A.; Larsen, B.; Skoug, R. M.

    2015-12-01

    Electromagnetic ion cyclotron (EMIC) waves are one of the key plasma waves that can affect charged particle dynamics in the Earth's inner magnetosphere. One of the generation mechanisms of EMIC waves has long been known to be due to magnetospheric compression due to impact by enhanced solar wind dynamic pressure Pdyn. With the Van Allen Probes observations, we have identified 4 EMIC wave events that are triggered by Pdyn enhancements under northward IMF, prolonged quiet time conditions. We find the following features of the EMIC events. (1) They are triggered immediately at the Pdyn impact and remain active during the same period as the enhanced Pdyn duration. (2) They occur in either H band or He band or both. (3) Two events occur inside the plasmasphere and the other two outside the plasmasphere. (4) The wave polarization, either R or L, are highly elliptical, being close to be linear. (5) The wave normal angles are quite large, well away from being field-aligned. (6) About 10 - 50 keV proton fluxes indicate enhanced flux state with ~90 deg-peaked anisotropy in velocity distribution after the Pdyn impact. (7) From low altitude NOAA POES satellite observations of particles we find no obvious evidence for relativistic electron precipitation due to these Pdyn-triggered EMIC events. We will discuss implications of these observations on wave generation mechanism and interaction with radiation belt electrons.

  4. Lattice dynamics of CaSiO3 at high temperatures and pressures

    Science.gov (United States)

    Holiday, A.; Sun, T.; Zhang, D.; Wentzcovitch, R. M.

    2012-12-01

    Cubic CaSiO3-perovskite is a minor but important phase of the Earth's lower mantle. Its thermodynamics and elastic properties have been investigated by multiple techniques but its behavior at lower mantle conditions is still elusive. It is a mechanically unstable phase at low temperatures but it is stabilized at lower mantle temperatures. We have investigated its vibrational properties at high pressures and temperatures of the lower mantle. We have projected ionic velocities from ab initio molecular dynamics trajectories onto vibrational normal modes and computed the mode-mode correlation functions from which we extract phonon frequencies and life times at finite temperatures. These correlations clearly indicate that normal modes with imaginary frequencies at 0 K are stabilized with increasing temperature. To overcome the finite size effect inherent in molecular dynamics simulations, a renormalized second-order force constant matrix in real space is constructed from the phonon frequencies at finite temperature and the phonon polarization vectors. Phonon dispersions and vibrational density of states are then determined by Fourier interpolation using the renormalized force constant matrix. These temperature dependent dispersions allow us to investigate thermodynamics and thermal elastic properties at lower mantle conditions.

  5. Lattice dynamics of cubic CaSiO3 perovskite at high temperatures and pressures

    Science.gov (United States)

    Sun, Tao; Zhang, Dong-Bo; Wentzcovitch, Renata M.

    2013-03-01

    Cubic CaSiO3-perovskite is a minor but important phase of the Earth's lower mantle. It is a mechanically unstable phase at low temperatures but it is stabilized at lower mantle temperatures. We have investigated its vibrational properties at high pressures and temperatures of the lower mantle. We have projected ionic velocities from ab initio molecular dynamics trajectories onto vibrational normal modes and computed the mode-mode correlation function from which we extract phonon frequencies and life times at finite temperatures. These correlations clearly indicate that normal modes with imaginary frequencies at 0 K are stabilized with increasing temperature. To overcome the finite size effect inherent in molecular dynamics simulations, a renormalized second-order force constant matrix in real space is constructed from the phonon frequencies at finite temperature and the phonon polarization vectors. Phonon dispersions and vibrational density of states are then determined by Fourier interpolation using the renormalized force matrix. These temperature dependent dispersions allow us to investigate thermodynamics and thermal elastic properties at lower mantle conditions. Supported by NSF Grants EAR-1047626 and EAR-0810272.

  6. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    Science.gov (United States)

    Abuzairi, Tomy; Okada, Mitsuru; Bhattacharjee, Sudeep; Nagatsu, Masaaki

    2016-12-01

    An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5-4.2 km/s and 2-7 × 1017 m-3. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from -900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  7. Early sepsis detection in critical care patients using multiscale blood pressure and heart rate dynamics.

    Science.gov (United States)

    Shashikumar, Supreeth P; Stanley, Matthew D; Sadiq, Ismail; Li, Qiao; Holder, Andre; Clifford, Gari D; Nemati, Shamim

    2017-08-16

    Sepsis remains a leading cause of morbidity and mortality among intensive care unit (ICU) patients. For each hour treatment initiation is delayed after diagnosis, sepsis-related mortality increases by approximately 8%. Therefore, maximizing effective care requires early recognition and initiation of treatment protocols. Antecedent signs and symptoms of sepsis can be subtle and unrecognizable (e.g., loss of autonomic regulation of vital signs), causing treatment delays and harm to the patient. In this work we investigated the utility of high-resolution blood pressure (BP) and heart rate (HR) times series dynamics for the early prediction of sepsis in patients from an urban, academic hospital, meeting the third international consensus definition of sepsis (sepsis-III) during their ICU admission. Using a multivariate modeling approach we found that HR and BP dynamics at multiple time-scales are independent predictors of sepsis, even after adjusting for commonly measured clinical values and patient demographics and comorbidities. Earlier recognition and diagnosis of sepsis has the potential to decrease sepsis-related morbidity and mortality through earlier initiation of treatment protocols. Copyright © 2017 Elsevier Inc. All rights reserved.

  8. Effect of high hydrostatic pressure and high dynamic pressure on stability and rheological properties of model oil-in-water emulsions

    Science.gov (United States)

    Bigikocin, Erman; Mert, Behic; Alpas, Hami

    2011-09-01

    Both static and dynamic high pressure applications provide interesting modifications in food structures which lead to new product formulations. In this study, the effects of two different treatments, high hydrostatic pressure (HHP) and high dynamic pressure (HDP), on oil-in-water emulsions were identified and compared. Microfluidization was selected from among the HDP homogenization techniques. The performance of each process was analyzed in terms of rheological modifications and emulsion stability improvements compared with the coarse emulsions. The stability of the emulsions was determined comparatively by using an analytical photo-centrifuge device employing novel analysis technology. Whey protein isolate (WPI) in combination with a food polysaccharide (xanthan gum, guar gum or locust bean gum) were used as emulsifying and stabilizing ingredients. The effective disruption of oil droplets and the degradation of polysaccharides by the shear forces under high pressure in HDP microfluidization yielded finer emulsions with lower viscosities, leading to distinctive improvements in emulsion stability. On the other hand, improvements in stability obtained with HHP treatment were due to the thickening of the emulsions mainly induced by protein unfolding. The corresponding increases in viscosity were intensified in emulsion formulations containing higher oil content. Apart from these, HHP treatment was found to be relatively more contributive to the enhancements in viscoelastic properties.

  9. Analytical solutions for dynamic pressures of coupling fluid-solid-porous medium due to P wave incidence

    Institute of Scientific and Technical Information of China (English)

    王进廷; 张楚汉; 金峰

    2004-01-01

    Wave reflection and refraction in layered media is a topic closely related to seismology, acoustics, geophysics and earthquake engineering. Analytical solutions for wave reflection and refraction coefficients in multi-layered media subjected to P wave incidence from the elastic half-space are derived in terms of displacement potentials. The system is composed of ideal fluid, porous medium, and underlying elastic solid. By numerical examples, the effects of porous medium and the incident wave angle on the dynamic pressures of ideal fluid are analyzed. The results show that the existence of the porous medium, especially in the partially saturated case, may significantly affect the dynamic pressures of the overlying fluid.

  10. Outer magnetospheric resonances and transport: discrete and turbulent cascades in the dynamic pressure and plasma flux

    Science.gov (United States)

    Savin, Sergey; Büchner, Jörg; Zelenyi, Lev; Kronberg, Elena; Kozak, Lyudmila; Blecki, Jan; Lezhen, Liudmila; Nemecek, Zdenek; Safrankova, Jana; Skalsky, Alexander; Budaev, Vyacheslav; Amata, Ermanno

    We explore interactions of Supersonic Plasma Streams (SPS) with the Earth magnetosphere in the context of the planetary and astrophysical magnetospheres and of that of laboratory plasmas. The interactions can be inherently non-local and non-equilibrium, and even explosive due to both solar wind (SW) induced and self-generated coherent structures in the multiscale system with the scales ranging from the micro to global scales. We concentrate on the main fundamental processes arising from the SPS cascading and interactions with surface and cavity resonances in the Earth’s magnetosphere, using multi-spacecraft data (SPECTR-R, DOUBLE STAR, CLUSTER, GEOTAIL, ACE, WIND etc.). We will address the following key problems to advance our understanding of anomalous transport and boundary dynamics: - generalizations of the SPS generation mechanisms, e.g., by bow shock (BS) surface or magnetosheath (MSH) cavity resonances, triggering by interplanetary shocks, solar wind (SW) dynamic pressure jumps, foreshock nonlinear structures, etc. - the clarification of BS rippling mechanisms requires base on the relevant databases from the CLUSTER/ DOUBLE STAR/ GEOTAIL/SPECTR-R/ ACE/ WIND spacecraft, which will be used for a statistical analysis targeting the SPS statistical features as extreme events. - substantial part of the SW kinetic energy can be pumped into the BS membrane and MSH cavity modes and initiate further cascades towards higher frequencies. Accordingly we present the multipoint studies of the SPS and of related nonlinear discrete cascades (carried generally by the SPS), along with the transformation of discrete cascades of the dynamic pressure into turbulent cascades. - investigation of spectral and bi-spectral cross-correlations in SW, foreshock, MSH and in vicinity of BS and magnetopause (MP) would demonstrate that both inflow and outflow into/ from magnetosphere can be modulated by the SPS and by the related outer magnetospheric resonances as well. We demonstrate in

  11. Dynamic aerofracture or hydrofracture of dense granular packing: pressure and viscosity control of the fracture patterns

    Science.gov (United States)

    Niebling, Michael J.; Toussaint, Renaud; Flekkøy, Eirik G.; Jørgen Måløy, Knut

    2013-04-01

    Stress induced by fluid or gases can cause diverse materials to break and fracture. Such hydraulic fractures are a natural and common phenomenon in the field of volcanism and are artificially initiated to enhance the recovery of natural gas and mineral oil by fracturing the reservoir rock with pressurized fluids. A procedure also known as fracking. Recently a new perspective on hydrofractures was added with the storage of supercritical CO2. In this respect two scenarios are considered. First it is one option to inject CO2 into existing hydrofractures, and second the injection of the CO2 can create additional fractures. The typical components for such fractures are a porous material and a compressible gas. The dynamics of such fractures and displacement patterns are simulated and studied in a rectangular Hele-Shaw cell filled with a dense but permeable two-dimensional granular layer. The model used, mixing highly deformable solid and fluid components, can simulate sedimentation problems [1,2], as well as hydrofracture or aerofracture ones. The emerging displacement patterns and fractures variate according to the properties of the injected fluid or gas and the characteristics of the granular phase [3]. The physics behind these variations is discussed and explained. The role of the fluid viscosity and system size shows to lead to a transition from fracturing to compaction, depending on the dynamics of convection versus diffusion of overpressure. The dependence of the obtained patterns on the injection pressure is also explored [4]. References: [1] Niebling, M.J., E.G. Flekkøy, K.J. Måløy, R. Toussaint, Sedimentation instabilities: impact of the fluid compressibility and viscosity, Phys. Rev. E 82, 051302, 2010. doi: 10.1103/PhysRevE.82.051302 [2] Niebling, M.J., E.G. Flekkøy, K.J. Måløy, R. Toussaint, Mixing of a granular layer falling through a fluid, Phys. Rev. E 82, 011301 (2010) doi: 10.1103/PhysRevE.82.011301 [3] Niebling, M., R. Toussaint, E.G. Flekk

  12. A data base and analysis program for shuttle main engine dynamic pressure measurements. Appendix F: Data base plots for SSME tests 750-120 through 750-200

    Science.gov (United States)

    Coffin, T.

    1986-01-01

    A dynamic pressure data base and data base management system developed to characterize the Space Shuttle Main Engine (SSME) dynamic pressure environment is presented. The data base represents dynamic pressure measurements obtained during single engine hot firing tests of the SSME. Software is provided to permit statistical evaluation of selected measurements under specified operating conditions. An interpolation scheme is also included to estimate spectral trends with SSME power level.

  13. [Value of dynamic arterial elastance in the predication of arterial pressure response to volume loading in shock patients].

    Science.gov (United States)

    Gong, Mao-lei; Liu, Da-wei; Wang, Xiao-ting; Chen, Xiu-kai

    2013-05-07

    To explore the value of dynamic arterial elastance (Eadyn) in the predication of arterial pressure response to volume loading in shock patients. A total of 32 patients with pulse indicator continuous cardiac output (PICCO) monitoring at our intensive care unit from January 2011 to December 2012 were retrospectively studied. The decision of fluid replacement was based upon the presence of shock (mean arterial pressure (MAP) ≤ 65 mm Hg, systolic arterial pressure arterial pressure response to volume loading. Significantly different between MAP responders and MAP nonresponders, baseline Eadyn was an effective predictor of MAP increase after volume loading. The area under the ROC curve was 0.95 for the prediction of volume loading on MAP for Eadyn at baseline (P 0.85 predicted a MAP increase after volume administration with a sensitivity of 89.5% and a specificity of 92.3%. Baseline Eadyn may predict accurately arterial pressure response in MAP to volume loading in shock patients.

  14. [Dynamic changes of the relationships between economic growth and environmental pressure in Gansu Province: a structural decomposition analysis].

    Science.gov (United States)

    Zhang, Zi-Long; Chen, Xing-Peng; Yang, Jing; Xue, Bing; Li, Yong-Jin

    2010-02-01

    Based on the ideology of macro environmental economics, a function of environmental pressure represented by pollutant emission was built, and the relative importance of the driving factors in the dynamic changes of the relationships between economic growth and environmental pressure in Gansu Province in 1990 - 2005 was analyzed by using structural decomposition analysis (SDA) model combining with 'refined Laspeyres' method. In the study period, the environmental pressure in the Province was mainly caused by the emission of waste gases and solids in the process of economic growth, and showed a rapid increasing trend at the late stage of the period. Population factor had less impact on the increase of this environmental pressure, while economic growth factor had obvious impact on it. Technological progress did mitigate, but could not offset the impact of economic growth factor, and the impacts of economic growth and technological factors on the environmental pressure differed with the kinds of pollutants.

  15. Dynamic Runner Forces and Pressure Fluctuations on the Draft Tube Wall of a Model Pump-Turbine

    Science.gov (United States)

    Kirschner, O.; Ruprecht, A.; Göde, E.; Riedelbauch, S.

    2016-11-01

    When Francis-turbines and pump-turbines operate at off-design conditions, typically a vortex rope develops. The vortex rope causes pressure oscillations leading to fluctuations of the forces affecting the runner. The presence of dynamic runner forces over a long period of time might damage the bearings and possibly the runner. In this experimental investigation, the fluctuating part of the runner forces and the pressure oscillations on the draft tube wall were measured on a model pump-turbine with a simplified straight cone draft tube in different operating conditions. The investigation focuses on the correlation of the pressure fluctuations frequency measured at the draft tube wall with the frequency of the fluctuating forces on the runner. The comparison between pressure fluctuations and dynamic forces shows a significant correlation in all operating points. For the comparison of different components in the spatial directions of the forces, the pressure fluctuations were separated in a synchronous part and a rotating part for operating points with higher amplitudes. The rotating pressure fluctuations correlate with the radial forces especially in the operating points with a rotating vortex rope. At frequencies with higher amplitudes in the pressure fluctuations caused by the vortex rope movement, there are also higher amplitudes in the radial forces at the same frequencies.

  16. Design of a Dynamic Seal to Enable Movement of a Film or Filament Through a Pressurized Space While Maintaining a Desired Pressure

    Science.gov (United States)

    Nicolae, Andrei

    The solid-state process has been successful in creating microcellular foams in a number of thermoplastic polymers using sub-critical CO2 in the 3-5 MPa range. In this process, the polymer film or sheet is first saturated with CO2 in a pressure vessel. The gas saturated film is then removed from the pressure vessel and heated in a suitable medium (liquid or hot air, for example) to create a microcellular structure. The time elapsed from depressurization of the pressure vessel to the heating of the gas-saturated film, known as the desorption time, is an important process parameter that can range from a few minutes in a laboratory environment to tens of minutes in a manufacturing environment. During the desorption time, the absorbed gas leaves the polymer film. This loss of gas becomes increasingly critical as the film thickness is reduced; polymer films below 0.010" in thickness are difficult or impossible to foam in the current solid-state batch process. To successfully foam thin films it is necessary for the polymer to retain the absorbed gas prior to heating. Towards this end, a dynamic seal was developed that allows a polymer film/filament to be smoothly drawn out of a pressure vessel while preventing the pressurized gas from escaping. The dynamic seal is based on the idea of using a liquid (e.g. water) to provide a seal and keep the pressurized gas from escaping. The liquid thus experiences the same pressure as the gas. Liquid leakage is controlled to within an acceptable limit by designing sufficient resistance to the flow. The early prototypes showed that a pressure of 5 MPa could be maintained in a small pressure vessel, while a 0.4 mm nylon fishing line was drawn through the seal. Water was used to seal the gas in this case. It was quickly apparent that the key challenge would be to move, or draw, the polymer film through the seal mechanism while keeping its integrity. The key is to strike a balance between sealing forces that keep the leakage rate low and

  17. Dynamic response of brittle materials from penetration and split Hopkinson pressure bar experiments

    Science.gov (United States)

    Frew, Danny Joe

    This research began with a study on the penetration of limestone targets with ogive-nose rod projectiles. Three sets of experiments were conducted with geometrically similar, steel rod projectiles that had length-to-diameter ratios of 10 and 7.1, 12.7, and 25.4-mm-diameters. Results from these penetration experiments and previously developed penetration models suggested that the limestone target exhibited strain-rate sensitivity. In order to investigate this hypothesis, an experimental/analytical program to study the dynamic material response of limestone was begun. As a first step, it was decided to focus on the dynamic material responses of brittle materials, such as limestone, under a state of one-dimensional stress. A split Hopkinson pressure bar (SHPB) facility was built at the Geotechnical and Structures Laboratory, U.S. Army Waterways Experiment Station. Early in the experimental program it became clear that new modifications had to be made to the traditional SHPB apparatus and experimental techniques. In addition, it was decided to model the responses of the SHPB apparatus and the sample under test in order to guide the experimental designs and minimize the experimental trials. The conventional split Hopkinson pressure bar apparatus was modified by shaping the incident pulse such that the samples are in dynamic stress equilibrium and have nearly constant strain rate over most of the test duration. A thin disk of annealed or hard C11000 copper is placed on the impact surface of the incident bar in order to shape the incident pulse. After impact by the striker bar, the copper disk deforms plastically and spreads the pulse in the incident bar. An analytical model and data show that a wide variety of incident strain pulses can be produced by varying the geometry of the copper disks and the length and striking velocity of the striker bar. The pulse shaping model predictions are in good agreement with measurements. Analytic models predict that a ramp stress pulse

  18. Perilymphatic pressure dynamics following posture change in patients with Meniere's disease and in normal hearing subjects

    NARCIS (Netherlands)

    Rosingh, HJ; Wit, HP; Albers, FWJ

    1998-01-01

    The hydrostatic pressure of the inner ear depends on the cerebrospinal fluid pressure through the cochlear aqueduct. The time-course of inner ear pressure change following rapid change in cerebrospinal fluid pressure is related to the aqueduct patency. In this study the patency of the cochlear aqued

  19. A Study of the Fluid-Dynamic Pressure Fields on Compressor Reed Valves.

    Science.gov (United States)

    1985-12-01

    nigher *A pressures. The total pressure ol the reservoir wnicn suppiieo the air was measured on either a lovi-incn mercury manometer or a3 -v)-incn... mercury manometer . This was the same manometer which was used to measure the total pressure of the reservoir. A pressure tap ran from this total

  20. Perilymphatic pressure dynamics following posture change in patients with Meniere's disease and in normal hearing subjects

    NARCIS (Netherlands)

    Rosingh, HJ; Wit, HP; Albers, FWJ

    The hydrostatic pressure of the inner ear depends on the cerebrospinal fluid pressure through the cochlear aqueduct. The time-course of inner ear pressure change following rapid change in cerebrospinal fluid pressure is related to the aqueduct patency. In this study the patency of the cochlear

  1. Features of energetic particle radial profiles inferred from geosynchronous responses to solar wind dynamic pressure enhancements

    Directory of Open Access Journals (Sweden)

    Y. Shi

    2009-02-01

    Full Text Available Determination of the radial profile of phase space density of relativistic electrons at constant adiabatic invariants is crucial for identifying the source for them within the outer radiation belt. The commonly used method is to convert flux observed at fixed energy to phase space density at constant first, second and third adiabatic invariants, which requires an empirical global magnetic field model and thus might produce some uncertainties in the final results. From a different perspective, in this paper we indirectly infer the shape of the radial profile of phase space density of relativistic electrons near the geosynchronous region by statistically examining the geosynchronous energetic flux response to 128 solar wind dynamic pressure enhancements during the years 2000 to 2003. We thus avoid the disadvantage of using empirical magnetic field models. Our results show that the flux response is species and energy dependent. For protons and low-energy electrons, the primary response to magnetospheric compression is an increase in flux at geosynchronous orbit. For relativistic electrons, the dominant response is a decrease in flux, which implies that the phase space density decreases toward increasing radial distance at geosynchronous orbit and leads to a local peak inside of geosynchronous orbit. The flux response of protons and non-relativistic electrons could result from a phase density that increases toward increasing radial distance, but this cannot be determined for sure due to the particle energization associated with pressure enhancements. Our results for relativistic electrons are consistent with previous results obtained using magnetic field models, thus providing additional confirmation that these results are correct and indicating that they are not the result of errors in their selected magnetic field model.

  2. Computational fluid dynamics (CFD) round robin benchmark for a pressurized water reactor (PWR) rod bundle

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Shin K., E-mail: paengki1@tamu.edu; Hassan, Yassin A.

    2016-05-15

    Highlights: • The capabilities of steady RANS models were directly assessed for full axial scale experiment. • The importance of mesh and conjugate heat transfer was reaffirmed. • The rod inner-surface temperature was directly compared. • The steady RANS calculations showed a limitation in the prediction of circumferential distribution of the rod surface temperature. - Abstract: This study examined the capabilities and limitations of steady Reynolds-Averaged Navier–Stokes (RANS) approach for pressurized water reactor (PWR) rod bundle problems, based on the round robin benchmark of computational fluid dynamics (CFD) codes against the NESTOR experiment for a 5 × 5 rod bundle with typical split-type mixing vane grids (MVGs). The round robin exercise against the high-fidelity, broad-range (covering multi-spans and entire lateral domain) NESTOR experimental data for both the flow field and the rod temperatures enabled us to obtain important insights into CFD prediction and validation for the split-type MVG PWR rod bundle problem. It was found that the steady RANS turbulence models with wall function could reasonably predict two key variables for a rod bundle problem – grid span pressure loss and the rod surface temperature – once mesh (type, resolution, and configuration) was suitable and conjugate heat transfer was properly considered. However, they over-predicted the magnitude of the circumferential variation of the rod surface temperature and could not capture its peak azimuthal locations for a central rod in the wake of the MVG. These discrepancies in the rod surface temperature were probably because the steady RANS approach could not capture unsteady, large-scale cross-flow fluctuations and qualitative cross-flow pattern change due to the laterally confined test section. Based on this benchmarking study, lessons and recommendations about experimental methods as well as CFD methods were also provided for the future research.

  3. Piezoluminescence at the air-water interface through dynamic molecular recognition driven by lateral pressure application.

    Science.gov (United States)

    Ariga, Katsuhiko; Nakanishi, Takashi; Terasaka, Yukiko; Tsuji, Hiromitsu; Sakai, Daisuke; Kikuchi, Jun-ichi

    2005-02-01

    The steroid cyclophanes with a cyclic core consisting of a 1,6,20,25-tetraaza[6.1.6.1]paracyclophane connected to four steroid moieties (cholic acid or cholanic acid) through a flexible l-lysine spacer were spread on water as Langmuir monolayers. The pi-A isotherm of the cholic-type steroid cyclophane includes a transition to the condensed phase with a limiting area of approximately 2 nm(2). This value is close to the cross-sectional area of the steroid cyclophane with a standing-up conformation of the cholic acid moieties, strongly suggesting that the cavity converts from a two-dimensional cavity to a three-dimensional cavity upon compressing the monolayer. Surface-reflective fluorescence spectroscopy of the monolayer using an aqueous fluorescent probe (6-(p-toluidino)naphthalene-2-sulfonate (TNS)) showed an abrupt increase in the TNS fluorescence intensity at a molecular area of 2 nm(2). Efficient binding of the guest probe would occur upon the completion of the three-dimensional cavity. Repeated compression and expansion induces periodic changes in the fluorescence intensity. This indicates a piezoluminescence effect through the catch and release of the TNS guest upon dynamic cavity formation. Analyses of the binding behavior of TNS to the steroid cyclophane resulted in binding constants in the range of approximately (5-9) x 10(4) M(-1) which are similar to that observed in lipid bilayer media (K = 5.1 x 10(4) M(-1)). The fluorescence intensity within the condensed phase was significantly increased with increasing pressure, suggesting that suppression of the molecular motion of the bound TNS may retard the nonemission process. Similar monolayer experiments were carried out with the monolayer of the cholanic-type steroid cyclophane that cannot form an open conformation on water. Both the phase transition in the pi-A isotherm and the change in the fluorescence intensity were negligible, confirming that the dynamic characteristic of the cavity is indispensable for

  4. The dynamic scale display digital pressure gauge%动态刻度显示数字压力表

    Institute of Scientific and Technical Information of China (English)

    王浩

    2014-01-01

    The dynamic scale display digital pressure gauge provides an intuitive dynamic pressure scale display, which not only uses the same digital pressure gauge and general digital display pressure values, and can be used LED string light off analog disc mechanical pressure gauge pointer indicates the instant value of the pressure, with the LED lights steady visual analog display measuring signal set upper limit, lower limit value.%针对现有数字压力表在显示方面的不足,开发设计了一种能够同时具有两种显示方式的动态刻度显示数字压力表。它不仅能够和一般数字压力表一样采用数码管显示压力值,而且可以用LED灯串模拟圆盘式机械压力表指针指示即时压力值,用常亮LED灯直观地模拟显示设定测量信号的上限值、下限值。

  5. A recurrence network approach for the analysis of skin blood flow dynamics in response to loading pressure.

    Science.gov (United States)

    Liao, Fuyuan; Jan, Yih-Kuen

    2012-06-01

    This paper presents a recurrence network approach for the analysis of skin blood flow dynamics in response to loading pressure. Recurrence is a fundamental property of many dynamical systems, which can be explored in phase spaces constructed from observational time series. A visualization tool of recurrence analysis called recurrence plot (RP) has been proved to be highly effective to detect transitions in the dynamics of the system. However, it was found that delay embedding can produce spurious structures in RPs. Network-based concepts have been applied for the analysis of nonlinear time series recently. We demonstrate that time series with different types of dynamics exhibit distinct global clustering coefficients and distributions of local clustering coefficients and that the global clustering coefficient is robust to the embedding parameters. We applied the approach to study skin blood flow oscillations (BFO) response to loading pressure. The results showed that global clustering coefficients of BFO significantly decreased in response to loading pressure (precurrence network approach can practically quantify the nonlinear dynamics of BFO.

  6. Simultaneous disappearances of plasmaspheric hiss, exohiss, and chorus waves triggered by a sudden decrease in solar wind dynamic pressure

    Science.gov (United States)

    Liu, Nigang; Su, Zhenpeng; Gao, Zhonglei; Zheng, Huinan; Wang, Yuming; Wang, Shui; Spence, H. E.; Reeves, G. D.; Baker, D. N.; Blake, J. B.; Funsten, H. O.; Wygant, J. R.

    2017-01-01

    Magnetospheric whistler mode waves are of great importance in the radiation belt electron dynamics. Here on the basis of the analysis of a rare event with the simultaneous disappearances of whistler mode plasmaspheric hiss, exohiss, and chorus triggered by a sudden decrease in the solar wind dynamic pressure, we provide evidences for the following physical scenarios: (1) nonlinear generation of chorus controlled by the geomagnetic field inhomogeneity, (2) origination of plasmaspheric hiss from chorus, and (3) leakage of plasmaspheric hiss into exohiss. Following the reduction of the solar wind dynamic pressure, the dayside geomagnetic field configuration with the enhanced inhomogeneity became unfavorable for the generation of chorus, and the quenching of chorus directly caused the disappearances of plasmaspheric hiss and then exohiss.

  7. Changes in Land Surface Water Dynamics since the 1990s and Relation to Population Pressure

    Science.gov (United States)

    Prigent, C.; Papa, F.; Aires, F.; Jimenez, C.; Rossow, W. B.; Matthews, E.

    2012-01-01

    We developed a remote sensing approach based on multi-satellite observations, which provides an unprecedented estimate of monthly distribution and area of land-surface open water over the whole globe. Results for 1993 to 2007 exhibit a large seasonal and inter-annual variability of the inundation extent with an overall decline in global average maximum inundated area of 6% during the fifteen-year period, primarily in tropical and subtropical South America and South Asia. The largest declines of open water are found where large increases in population have occurred over the last two decades, suggesting a global scale effect of human activities on continental surface freshwater: denser population can impact local hydrology by reducing freshwater extent, by draining marshes and wetlands, and by increasing water withdrawals. Citation: Prigent, C., F. Papa, F. Aires, C. Jimenez, W. B. Rossow, and E. Matthews (2012), Changes in land surface water dynamics since the 1990s and relation to population pressure, in section 4, insisting on the potential applications of the wetland dataset.

  8. Gas Kinematics on GMC scales in M51 with PAWS: cloud stabilization through dynamical pressure

    CERN Document Server

    Meidt, Sharon E; Garcia-Burillo, Santiago; Hughes, Annie; Colombo, Dario; Pety, Jerome; Dobbs, Clare L; Schuster, Karl F; Kramer, Carsten; Leroy, Adam K; Dumas, Gaelle; Thompson, Todd A

    2013-01-01

    We use the high spatial and spectral resolution of the PAWS CO(1-0) survey of the inner 9 kpc of the iconic spiral galaxy M51 to examine the effect of gas streaming motions on the star-forming properties of individual GMCs. We compare our view of gas flows in M51 -- which arise due to departures from axi-symmetry in the gravitational potential (i.e. the nuclear bar and spiral arms) -- with the global pattern of star formation as traced by Halpha and 24\\mu m emission. We find that the dynamical environment of GMCs strongly affects their ability to form stars, in the sense that GMCs situated in regions with large streaming motions can be stabilized, while similarly massive GMCs in regions without streaming go on to efficiently form stars. We argue that this is the result of reduced surface pressure felt by clouds embedded in an ambient medium undergoing large streaming motions, which prevents collapse. Indeed, the variation in gas depletion time expected based on the observed streaming motions throughout the di...

  9. Dayside magnetospheric ULF wave frequency modulated by a solar wind dynamic pressure negative impulse

    Science.gov (United States)

    Shen, X. C.; Shi, Q. Q.; Zong, Q.-G.; Tian, A. M.; Nowada, M.; Sun, W. J.; Zhao, H. Y.; Hudson, M. K.; Wang, H. Z.; Fu, S. Y.; Pu, Z. Y.

    2017-02-01

    Ultralow frequency (ULF) waves play an important role in the transport of the solar wind energy to the magnetosphere. In this paper, we present a ULF wave event in the dayside magnetosphere which shows a sudden decrease in frequency from 3.1 to 2.3 mHz around 0756 UT on 11 January 2010, when a solar wind dynamic pressure drop (from ˜5 to ˜2 nPa) was observed simultaneously. The wave exits globally. The phase differences between electric and magnetic fields indicate that the compressional mode wave is standing before and after the wave frequency decrease. This result suggests that the ULF wave should be associated with a cavity mode and the frequency decrease might be induced by the change of the cavity size. A theoretical calculation was made to estimate the cavity mode frequency. The calculated wave frequency before/after the negative impulse is 3.8/2.6 mHz, which is consistent with the observations.

  10. Dynamic cerebral autoregulation to induced blood pressure changes in human experimental and clinical sepsis

    DEFF Research Database (Denmark)

    Berg, Ronan M G; Plovsing, Ronni R; Bailey, Damian M

    2016-01-01

    (Pvolunteers at baseline; Pvolunteers after LPS). The corresponding RoR values increased from 0·46 (0·31-0·49) s(-1) at baseline to 0·58 (0·36-0·74) s(-1) after LPS (Pvolunteers, whereas they were similar to values observed in patients [0·43 (0·36-0·52) s...... shock. In this study, we hypothesized that this pattern of response would be identical during induced changes in blood pressure. Dynamic cerebral autoregulation was assessed in nine healthy volunteers and six septic patients. The healthy volunteers underwent a 4-h intravenous infusion of LPS (total dose......R). This was performed before and after LPS infusion in healthy volunteers, and within 72 h following clinical diagnosis of sepsis in patients. In healthy volunteers, thigh-cuff deflation caused a MAP reduction of 16 (13-20) % at baseline and 18 (16-20) % after LPS, while the MAP reduction was 12 (11-13) % in patients...

  11. Geosynchronous magnetic field responses to fast solar wind dynamic pressure enhancements: MHD field model

    Directory of Open Access Journals (Sweden)

    T. R. Sun

    2012-08-01

    Full Text Available We performed global MHD simulations of the geosynchronous magnetic field in response to fast solar wind dynamic pressure (Pd enhancements. Taking three Pd enhancement events in 2000 as examples, we found that the main features of the total field B and the dominant component Bz can be efficiently predicted by the MHD model. The predicted B and Bz varies with local time, with the highest level near noon and a slightly lower level around mid-night. However, it is more challenging to accurately predict the responses of the smaller component at the geosynchronous orbit (i.e., Bx and By. In contrast, the limitations of T01 model in predicting responses to fast Pd enhancements are presented.

  12. Array of surface-confined glow discharges in atmospheric pressure helium: Modes and dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Li, D.; Liu, D. X., E-mail: liudingxin@gmail.com, E-mail: mglin5g@gmail.com [Center for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Shaanxi (China); Nie, Q. Y.; Li, H. P. [Department of Engineering Physics, Tsinghua University, Beijing 100084 (China); Chen, H. L. [Frank Reidy Center for Bioelectrics, Old Dominion University, Norfolk, Virginia 23508 (United States); Kong, M. G., E-mail: liudingxin@gmail.com, E-mail: mglin5g@gmail.com [Center for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Shaanxi (China); Frank Reidy Center for Bioelectrics, Old Dominion University, Norfolk, Virginia 23508 (United States); Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, Virginia 23529 (United States)

    2014-05-19

    Array of atmospheric pressure surface discharges confined by a two-dimensional hexagon electrode mesh is studied for its discharge modes and temporal evolution so as to a theoretical underpinning to their growing applications in medicine, aerodynamic control, and environmental remediation. Helium plasma surface-confined by one hexagon-shaped rim electrode is shown to evolve from a Townsend mode to a normal and abnormal glow mode, and its evolution develops from the rim electrodes as six individual microdischarges merging in the middle of the hexagon mesh element. Within one hexagon element, microdischarges remain largely static with the mesh electrode being the instantaneous cathode, but move towards the hexagon center when the electrode is the instantaneous anode. On the entire array electrode surface, plasma ignition is found to beat an unspecific hexagon element and then spreads to ignite surrounding hexagon elements. The spreading of microdischarges is in the form of an expanding circle at a speed of about 3 × 10{sup 4} m/s, and their quenching starts in the location of the initial plasma ignition. Plasma modes influence how input electrical power is used to generate and accelerate electrons and as such the reaction chemistry, whereas plasma dynamics are central to understand and control plasma instabilities. The present study provides an important aspect of plasma physics of the atmospheric surface-confined discharge array and a theoretical underpinning to its future technological innovation.

  13. Pressure and temperature dependence of the laser-induced plasma plume dynamics

    Science.gov (United States)

    Ojeda-G-P, Alejandro; Schneider, Christof W.; Lippert, Thomas; Wokaun, Alexander

    2016-12-01

    The influence of different background gases and substrate heating on the plasma plume dynamics from silver ablation is investigated by species selected time and space resolved imaging. The results provide a time-resolved understanding on how those process parameters affect the expansion: from a free expansion in vacuum with velocities exceeding 20 000 m/s to a very slow expansion in Ar at 1 × 10-1 mbar with arrival velocities of 280 m/s. In addition, we observe a rebound of the ablated material on the substrate holder leading to a re-coating of the ablated target. At 1 × 10-1 mbar, it seems that the expansion of the plasma plume displaces a considerable portion of the background gas and traps it against the frontal area of the substrate holder. This leads to a transient high local pressure just above the substrate. In the case of Ar, the rebound is enhanced due to inelastic scattering, whereas for an O2 background, an area of high reactivity/emission in addition to the rebound is created. Imaging of selected species shows that the light emission in this area is mainly due to excited Ag and metal oxygen species. There is a clear influence of substrate heating on the plasma expansion due to the background gas density gradients, reducing the stopping ability of the background gas and already detectable 2 cm away from the substrate. Both rebound and excitation effects are reduced in intensity due to the substrate heating.

  14. A dynamical point of view of Quantum Information: entropy and pressure

    CERN Document Server

    Baraviera, A; Lopes, A O; Cunha, M Terra

    2011-01-01

    Quantum Information is a new area of research which has been growing rapidly since last decade. This topic is very close to potential applications to the so called Quantum Computer. In our point of view it makes sense to develop a more "dynamical point of view" of this theory. We want to consider the concepts of entropy and pressure for "stationary systems" acting on density matrices which generalize the usual ones in Ergodic Theory (in the sense of the Thermodynamic Formalism of R. Bowen, Y. Sinai and D. Ruelle). We consider the operator $\\mathcal{L}$ acting on density matrices $\\rho\\in \\mathcal{M}_N$ over a finite $N$-dimensional complex Hilbert space $\\mathcal{L}(\\rho):=\\sum_{i=1}^k tr(W_i\\rho W_i^*)V_i\\rho V_i^*,$ where $W_i$ and $V_i$, $i=1,2,...k$ are operators in this Hilbert space. $\\mathcal{L}$ is not a linear operator. In some sense this operator is a version of an Iterated Function System (IFS). Namely, the $V_i\\,(.)\\,V_i^*=:F_i(.)$, $i=1,2,...,k$, play the role of the inverse branches (acting on t...

  15. Dynamics in the vicinity of (101955) Bennu: solar radiation pressure effects in equatorial orbits

    Science.gov (United States)

    Chanut, T. G. G.; Aljbaae, S.; Prado, A. F. B. A.; Carruba, V.

    2017-09-01

    Here, we study the dynamical effects of the solar radiation pressure (SRP) on a spacecraft that will survey the near-Earth rotating asteroid (101955) Bennu when the projected shadow is accounted for. The spacecraft's motion near (101955) Bennu is modelled in the rotating frame fixed at the centre of the asteroid, neglecting the Sun gravity effects. We calculate the SRP at the perihelion, semimajor axis and aphelion distances of the asteroid from the Sun. The goals of this work are to analyse the stability for both homogeneous and inhomogeneous mass distribution and study the effects of the SRP in equatorial orbits close to the asteroid (101955) Bennu. As results, we find that the mascon model divided into 10 equal layers seems to be the most suitable for this problem. We can highlight that the centre point E8, which was linearly stable in the case of the homogeneous mass distribution, becomes unstable in this new model changing its topological structure. For a Sun initial longitude ψ0 = -180°, starting with the spacecraft longitude λ = 0, the orbits suffer fewer impacts and some (between 0.4 and 0.5 km), remaining unwavering even if the maximum solar radiation is considered. When we change the initial longitude of the Sun to ψ0 = -135°, the orbits with initial longitude λ = 90° appear to be more stable. Finally, when the passage of the spacecraft in the shadow is accounted for, the effects of SRP are softened, and we find more stable orbits.

  16. Dynamical Generation of a Repulsive Vector Contribution to the Quark Pressure

    CERN Document Server

    Restrepo, Tulio E; Pinto, Marcus Benghi; Ferrari, Gabriel N

    2014-01-01

    Lattice QCD results for the coefficient $c_2$ appearing in the Taylor expansion of the pressure show that this quantity raises with the temperature towards the Stefan-Boltzmann limit. On the other hand, model approximations predict that when a vector repulsion, parametrized by $G_V$, is present this coefficient reaches a maximum just after $T_c$ and then deviates from the lattice predictions. Recently, this discrepancy has been used as a guide to constrain the (presently unknown) value of $G_V$ within the framework of effective models at large-$N_c$ (LN). In the present investigation we show that, due to finite $N_c$ effects, $c_2$ may also develop a maximum even when $G_V=0$ since a vector repulsive term can be dynamically generated by exchange type of radiative corrections. Here we apply the the Optimized Perturbation Theory (OPT) method to the two flavor Polyakov--Nambu--Jona-Lasinio model (at $G_V=0$) and compare the results with those furnished by lattice simulations an by the LN approximation at $G_V=0$...

  17. Distribution of Side Abutment Stress in Roadway Subjected to Dynamic Pressure and Its Engineering Application

    Directory of Open Access Journals (Sweden)

    Yao Qiangling

    2015-01-01

    Full Text Available The borehole stress-meter was employed in this study to investigate the distribution of the side abutment stress in roadway subjected to dynamic pressure. The results demonstrate that the side abutment stress of the mining roadway reaches a peak value when the distance to the gob is 8 m and the distribution curve of the side abutment stress can be divided into three zones: stress rising zone, stress stabilizing zone, and stress decreasing zone. Further numerical investigation was carried out to study the effect of the coal mass strength, coal seam depth, immediate roof strength, and thickness on the distribution of the side abutment stress. Based on the research results, we determined the reasonable position of the mining roadway and the optimal width of the barrier pillar. The engineering application demonstrates that the retention of the barrier pillar with a width of 5 m along the gob as the haulage roadway for the next panel is feasible, which delivers favorable technological and economic benefits.

  18. Computational Fluid Dynamics Simulation of Combustion Instability in Solid Rocket Motor : Implementation of Pressure Coupled Response Function

    Directory of Open Access Journals (Sweden)

    S. Saha

    2016-04-01

    Full Text Available Combustion instability in solid propellant rocket motor is numerically simulated by implementing propellant response function with quasi steady homogeneous one dimensional formulation. The convolution integral of propellant response with pressure history is implemented through a user defined function in commercial computational fluid dynamics software. The methodology is validated against literature reported motor test and other simulation results. Computed amplitude of pressure fluctuations compare closely with the literarture data. The growth rate of pressure oscillations of a cylindrical grain solid rocket motor is determined for different response functions at the fundamental longitudinal frequency. It is observed that for response function more than a critical value, the motor exhibits exponential growth rate of pressure oscillations.

  19. Quasi-elastic neutron scattering study on water and polymer dynamics in thermo/pressure sensitive polymer solutions.

    Science.gov (United States)

    Osaka, Noboru; Shibayama, Mitsuhiro; Kikuchi, Tatsuya; Yamamuro, Osamu

    2009-10-01

    Dynamics of water and poly(N-isopropylacrylamide) (PNIPA) in concentrated aqueous solutions, where the majority of water molecules are attached to polymer chains, has been investigated with use of incoherent quasi-elastic neutron scattering (QENS) and dynamic light scattering (DLS) measurements as functions of temperature, T, and hydrostatic pressure, P. It was observed by QENS that the self-diffusion coefficient, D(water), of water in PNIPA/H(2)O solutions increased by P at temperatures below the lower critical solution temperature (LCST) of PNIPA aqueous solutions. However, above the LCST, D(water) decreased by P, as is often reported in non-hydrogen bonding solutions. In isobaric heating runs, therefore, the jump in D(water) at LCST decreased with increasing pressure. On the other hand, the mean-square displacement, , of the local vibrational motion of PNIPA in PNIPA/D(2)O solutions, where the incoherent scattering signal of PNIPA was predominantly observed, was reduced due to the aggregation behavior of PNIPA by pressurizing, which was also confirmed by using DLS. The jump in at the LCST became gradual by pressurizing, which was consistent with the changes of the dynamics of water obtained in PNIPA/H(2)O solutions.

  20. Modeling the fluid-dynamics and oxygen consumption in a porous scaffold stimulated by cyclic squeeze pressure.

    Science.gov (United States)

    Ferroni, Marco; Giusti, Serena; Nascimento, Diana; Silva, Ana; Boschetti, Federica; Ahluwalia, Arti

    2016-08-01

    The architecture and dynamic physical environment of tissues can be recreated in-vitro by combining 3D porous scaffolds and bioreactors able to apply controlled mechanical stimuli on cells. In such systems, the entity of the stimuli and the distribution of nutrients within the engineered construct depend on the micro-structure of the scaffolds. In this work, we present a new approach for optimizing computational fluid-dynamics (CFD) models for the investigation of fluid-induced forces generated by cyclic squeeze pressure within a porous construct, coupled with oxygen consumption of cardiomyocytes. A 2D axial symmetric macro-scaled model of a squeeze pressure bioreactor chamber was used as starting point for generating time dependent pressure profiles. Subsequently the fluid movement generated by the pressure fields was coupled with a complete 3D micro-scaled model of a porous protein cryogel. Oxygen transport and consumption inside the scaffold was evaluated considering a homogeneous distribution of cardiomyocytes throughout the structure, as confirmed by preliminary cell culture experiments. The results show that a 3D description of the system, coupling a porous geometry and time dependent pressure driven flow with fluid-structure-interaction provides an accurate and meaningful description of the microenvironment in terms of shear stress and oxygen distribution than simple stationary 2D models.

  1. Indication for shunt operation of normal pressure hydrocephalus. Combined assessment of infusion test and dynamic CT scan

    Energy Technology Data Exchange (ETDEWEB)

    Jinnai, Takahiro; Nagao, Seigo [Kagawa Medical Univ., Miki (Japan); Kuyama, Hideyuki

    2000-03-01

    Normal pressure hydrocephalus (NPH) is one of the diseases that causes a neuro-surgically treatable form of dementia. Although patients with NPH can be treated with shunt operation, reliable indications for the surgery are not yet established. In this study, 20 NPH patients diagnosed by clinical symptoms were subjected to combined assessment by infusion test and dynamic CT scan, a useful diagnostic tool to select a shunt responsive cases. Patients were evaluated by measuring sequential changes in the density of the periventricular lucency (PVL) using dynamic CT scan and continuous lumbar subdural pressure monitoring during an infusion manometric test at a rate of 0.8 ml/min for 30 min. The average lumbar subdural pressure during infusion manometric test in the shunt responsive group was 18.4{+-}5.8 mmHg, which was significantly higher than that in the shunt non-responsive group which was 10.0{+-}4.0 mmHg (p<0.01). The relative changes in PVL density in the dynamic CT was also significantly higher in the shunt responsive group (0.99{+-}0.61 HU) compared to the shunt non-responsive group (0.15{+-}0.32) (p<0.01). Dynamic CT scan with infusion manometric test is useful in the selection of patients with NPH who are likely to respond to shunt surgery. (author)

  2. Dynamic Changes of Pulmonary Arterial Pressure and Ductus Arteriosus in Human Newborns From Birth to 72 Hours of Age

    OpenAIRE

    2016-01-01

    Abstract Normal pulmonary artery pressure and pulmonary hypertension assessment of newborns is rarely reported. The aim of the study is to explore dynamic changes of pulmonary arterial pressure and ductus arteriosus in human newborns from birth to 72 h of age with echocardiography. A total of 76 cases of normal newborns were prospectively detected by echocardiography after birth of 2 h, 6 h, 12 h, 24 h, 48 h, and 72 h, respectively. Ductus arteriosus diameter, blood shunt direction, blood flo...

  3. Noninvasive estimation of dynamic pressures in vitro and in vivo using the subharmonic response from microbubbles.

    Science.gov (United States)

    Dave, Jaydev K; Halldorsdottir, Valgerdur G; Eisenbrey, John R; Liu, Ji-Bin; McDonald, Maureen E; Dickie, Kris; Leung, Corina; Forsberg, Flemming

    2011-10-01

    The purpose of this study was to develop and validate a noninvasive pressure estimation technique based on subharmonic emissions from a commercially available ultrasound contrast agent and scanner, unlike other studies that have either adopted a single-element transducer approach and/ or use of in-house contrast agents. Ambient pressures were varied in a closed-loop flow system between 0 and 120 mmHg and were recorded by a solid-state pressure catheter as the reference standard. Simultaneously, the ultrasound scanner was operated in pulse inversion mode transmitting at 2.5 MHz, and the unprocessed RF data were captured at different incident acoustic pressures (from 76 to 897 kPa). The subharmonic data for each pulse were extracted using band-pass filtering with averaging, and subsequently processed to eliminate noise. The incident acoustic pressure most sensitive to ambient pressure fluctuations was determined, and then the ambient pressure was tracked over 20 s. In vivo validation of this technique was performed in the left ventricle (LV) of 2 canines. In vitro, the subharmonic signal could track ambient pressure values with r(2) = 0.922 (p subharmonic signal tracked the LV pressures with r(2) > 0.790 (p subharmonic ultrasound-based pressure estimation technique, which can accurately track left ventricular pressures, has been established.

  4. Three-Dimensional Mathematical Investigation of Dynamic and Hydrostatic Pressure Distributions on Planing Hulls

    Directory of Open Access Journals (Sweden)

    Parviz Ghadimi

    2013-01-01

    Full Text Available A mathematical model is utilized in order to calculate three-dimensional pressure distributions on planing hulls. This type of modeling is able to determine the hydrodynamic and hydrostatic pressures acting on the bottom of these hulls. As a result, the total 3-dimensional pressure exerted on the planing hull as a sum of hydrostatic and hydrodynamic pressures can be evaluated. Empirical equations introduced in previous works have been used as the fundamentals for the present mathematical modeling method. The obtained results are compared against available experimental results and results of empirical equations in order to validate the proposed method. The outcome of the -squared tests conducted on these comparisons shows favorable accuracy of the results. After evaluation of hydrodynamic pressure, the effects of trim and deadrise angles and wetted length on the 3-dimensional pressure distribution are analyzed. Finally, the total pressure on planing hull and the effect of velocity coefficients are studied.

  5. Ambulatory blood pressure and Doppler echocardiographic indexes of borderline hypertensive men presenting an exaggerated blood pressure response during dynamic exercise

    Directory of Open Access Journals (Sweden)

    Herkenhoff F.L.

    2001-01-01

    Full Text Available Borderline hypertension (BH has been associated with an exaggerated blood pressure (BP response during laboratory stressors. However, the incidence of target organ damage in this condition and its relation to BP hyperreactivity is an unsettled issue. Thus, we assessed the Doppler echocardiographic profile of a group of BH men (N = 36 according to office BP measurements with exaggerated BP in the cycloergometric test. A group of normotensive men (NT, N = 36 with a normal BP response during the cycloergometric test was used as control. To assess vascular function and reactivity, all subjects were submitted to the cold pressor test. Before Doppler echocardiography, the BP profile of all subjects was evaluated by 24-h ambulatory BP monitoring. All subjects from the NT group presented normal monitored levels of BP. In contrast, 19 subjects from the original BH group presented normal monitored BP levels and 17 presented elevated monitored BP levels. In the NT group all Doppler echocardiographic indexes were normal. All subjects from the original BH group presented normal left ventricular mass and geometrical pattern. However, in the subjects with elevated monitored BP levels, fractional shortening was greater, isovolumetric relaxation time longer, and early to late flow velocity ratio was reduced in relation to subjects from the original BH group with normal monitored BP levels (P<0.05. These subjects also presented an exaggerated BP response during the cold pressor test. These results support the notion of an integrated pattern of cardiac and vascular adaptation during the development of hypertension.

  6. Semi-supervised detection of intracranial pressure alarms using waveform dynamics.

    Science.gov (United States)

    Scalzo, Fabien; Hu, Xiao

    2013-04-01

    Patient monitoring systems in intensive care units (ICU) are usually set to trigger alarms when abnormal values are detected. Alarms are generated by threshold-crossing rules that lead to high false alarm rates. This is a recognized issue that causes alarm fatigue, waste of human resources, and increased patient risks. Recently developed smart alarm models require alarms to be validated by experts during the training phase. The manual annotation process involved is time-consuming and virtually impossible to achieve for the thousands of alarms recorded in the ICU every week. To tackle this problem, we investigate in this study if the use of semi-supervised learning methods, that can naturally integrate unlabeled data samples in the model, can be used to improve the accuracy of the alarm detection. As a proof of concept, the detection system is evaluated on intracranial pressure (ICP) signal alarms. Specific morphological and trending features are extracted from the ICP signal waveform to capture the dynamic of the signal prior to alarms. This study is based on a comprehensive dataset of 4791 manually labeled alarms recorded from 108 neurosurgical patients. A comparative analysis is provided between kernel spectral regression (SR-KDA) and support vector machine (SVM) both modified for the semi-supervised setting. Results obtained during the experimental evaluations indicate that the two models can significantly reduce false alarms using unlabeled samples; especially in the presence of a restrained number of labeled examples. At a true alarm recognition rate of 99%, the false alarm reduction rates improved from 9% (supervised) to 27% (semi-supervised) for SR-KDA, and from 3% (supervised) to 16% (semi-supervised) for SVM.

  7. Influence of voltage magnitude on the dynamic behavior of a stable helium atmospheric pressure plasma jet

    Science.gov (United States)

    Ning, Wenjun; Wang, Lijun; Wu, Chen; Jia, Shenli

    2014-08-01

    Effects of voltage magnitude on the development of a stable helium atmospheric pressure plasma jet are investigated by current measurements and high temporal-resolution streak images. Generated by a coaxial dielectric barrier discharge structure, the entire discharge can be classified into three regions: discharges in the tube gap, downstream jet, and up-streamer. The discharge morphologies of each region are analyzed. In the positive discharge phase, there are two discharges in the tube gap between the electrodes; the first one is ignited as corona and then developed into streamer corona, and the second one is similar with positive glow. The downstream jet is ignited independently from the discharge in the tube gap. Referred as "plasma bullet," the dynamic behavior of the jet can be well described as a positive streamer. Under specific applied voltage, the jet is found to be composed by double bullets in which case the jet length decreases since that less charge is carried by the first bullet. The up-streamer can be captured as long as the discharge in the tube gap is activated. Propagating with velocity of ˜4 km/s, the up-streamer can be regarded as the extension of the first discharge in the tube gap. In the negative discharge phase, the discharge is confined in the tube gap with nearly symmetrical morphology with the positive one. Besides, with the rising of voltage, the negative discharge is initially intensified and then turns weaker after surpassing certain voltage, which may provide suitable condition for the occurrence of double-bullet phenomenon.

  8. The impalement of water drops impinging onto hydrophobic/superhydrophobic graphite surfaces: the role of dynamic pressure, hammer pressure and liquid penetration time

    Science.gov (United States)

    Pittoni, Paola G.; Lin, Ya-Chi; Lin, Shi-Yow

    2014-05-01

    Droplet impingement experiments at low Weber numbers were conducted by digitizing silhouettes of impacting water drops onto unlike graphite substrates, typified by different advancing water contact angles (θa): 140 and 160°. The relaxation of wetting diameter, dynamic contact angle, and drop shapes were measured. The purpose was to carefully investigate the phenomenology and possible causes of the failure of the superhydrophobicity. During impact and spreading phases, all the drops impinging onto both graphite substrates showed a similar behavior. Then, after an initial free recoil, drops impinging at lower impact velocities onto graphite substrates characterized by θa = 140° clearly exhibited time intervals in which the wetting diameter appeared to be almost constant. The duration of this pinned phase was observed decreasing with increasing the impact height and almost completely disappearing for drops impinging at higher impact velocities. This behavior has never been reported before, and, contrariwise, water droplets impinging at lower impact velocities onto hydrophobic and superhydrophobic surfaces have been generally observed more freely retracting, and ultimately rebounding, compared to drops impacting at higher velocities. In the present study, this latter behavior was recorded just for drops impinging onto graphite surfaces characterized by θa = 160°. A theoretical description of the experimental results was proposed, specifically investigating the role of dynamic pressure, hammer pressure and liquid penetration time during the impact, spreading and recoil stages.

  9. Molecular Dynamics of Equilibrium and Pressure-Driven Transport Properties of Water through LTA-Type Zeolites

    KAUST Repository

    Turgman-Cohen, Salomon

    2013-10-08

    We consider an atomistic model to investigate the flux of water through thin Linde type A (LTA) zeolite membranes with differing surface chemistries. Using molecular dynamics, we have studied the flow of water under hydrostatic pressure through a fully hydrated LTA zeolite film (∼2.5 nm thick) capped with hydrophilic and hydrophobic moieties. Pressure drops in the 50-400 MPa range were applied across the membrane, and the flux of water was monitored for at least 15 ns of simulation time. For hydrophilic membranes, water molecules adsorb at the zeolite surface, creating a highly structured fluid layer. For hydrophobic membranes, a depletion of water molecules occurs near the water/zeolite interface. For both types of membranes, the water structure is independent of the pressure drop established in the system and the flux through the membranes is lower than that observed for the bulk zeolitic material; the latter allows an estimation of surface barrier effects to pressure-driven water transport. Mechanistically, it is observed that (i) bottlenecks form at the windows of the zeolite structure, preventing the free flow of water through the porous membrane, (ii) water molecules do not move through a cage in a single-file fashion but rather exhibit a broad range of residence times and pronounced mixing, and (iii) a periodic buildup of a pressure difference between inlet and outlet cages takes place which leads to the preferential flow of water molecules toward the low-pressure cages. © 2013 American Chemical Society.

  10. Partially implicit finite difference scheme for calculating dynamic pressure in a terrain-following coordinate non-hydrostatic ocean model

    Science.gov (United States)

    Liu, Zhe; Lin, Lei; Xie, Lian; Gao, Huiwang

    2016-10-01

    To improve the efficiency of the terrain-following σ-coordinate non-hydrostatic ocean model, a partially implicit finite difference (PIFD) scheme is proposed. By using explicit terms instead of implicit terms to discretize the parts of the vertical dynamic pressure gradient derived from the σ-coordinate transformation, the coefficient matrix of the discrete Poisson equation that the dynamic pressure satisfies can be simplified from 15 diagonals to 7 diagonals. The PIFD scheme is shown to run stably when it is applied to simulate five benchmark cases, namely, a standing wave in a basin, a surface solitary wave, a lock-exchange problem, a periodic wave over a bar and a tidally induced internal wave. Compared with the conventional fully implicit finite difference (FIFD) scheme, the PIFD scheme produces simulation results of equivalent accuracy at only 40-60% of the computational cost. The PIFD scheme demonstrates strong applicability and can be easily implemented in σ-coordinate ocean models.

  11. Multibody Dynamics of a Fluid Power Radial Piston Motor Including Transient Hydrodynamic Pressure Models of Lubricating Gaps

    DEFF Research Database (Denmark)

    Johansen, Per; Rømer, Daniel; Andersen, Torben Ole

    2014-01-01

    is a multibody dynamics model of a radial piston fluid power motor, which connects the rigid bodies through models of the transient hydrodynamic lubrication pressure in the joint clearance. A finite volume approach is used to model the pressure dynamics of the fluid film lubrication. The model structure......The increasing interest in hydraulic transmissions in wind and wave energy applications has created an incentive for the development of high efficiency fluid power machinery. Modeling and analysis of fluid power machinery loss mechanisms are necessary in order to accommodate this demand. At present...... fully coupled thermo-elastic models has been used to simulate and study loss mechanisms in various tribological interfaces. Consequently, a reasonable focus of further development is to couple the interface models and the rigid body mechanics of fluid power machinery. The focus of the current paper...

  12. Global surface pressure measurements of static and dynamic stall on a wind turbine airfoil at low Reynolds number

    Science.gov (United States)

    Disotell, Kevin J.; Nikoueeyan, Pourya; Naughton, Jonathan W.; Gregory, James W.

    2016-05-01

    Recognizing the need for global surface measurement techniques to characterize the time-varying, three-dimensional loading encountered on rotating wind turbine blades, fast-responding pressure-sensitive paint (PSP) has been evaluated for resolving unsteady aerodynamic effects in incompressible flow. Results of a study aimed at demonstrating the laser-based, single-shot PSP technique on a low Reynolds number wind turbine airfoil in static and dynamic stall are reported. PSP was applied to the suction side of a Delft DU97-W-300 airfoil (maximum thickness-to-chord ratio of 30 %) at a chord Reynolds number of 225,000 in the University of Wyoming open-return wind tunnel. Static and dynamic stall behaviors are presented using instantaneous and phase-averaged global pressure maps. In particular, a three-dimensional pressure topology driven by a stall cell pattern is detected near the maximum lift condition on the steady airfoil. Trends in the PSP-measured pressure topology on the steady airfoil were confirmed using surface oil visualization. The dynamic stall case was characterized by a sinusoidal pitching motion with mean angle of 15.7°, amplitude of 11.2°, and reduced frequency of 0.106 based on semichord. PSP images were acquired at selected phase positions, capturing the breakdown of nominally two-dimensional flow near lift stall, development of post-stall suction near the trailing edge, and a highly three-dimensional topology as the flow reattaches. Structural patterns in the surface pressure topologies are considered from the analysis of the individual PSP snapshots, enabled by a laser-based excitation system that achieves sufficient signal-to-noise ratio in the single-shot images. The PSP results are found to be in general agreement with observations about the steady and unsteady stall characteristics expected for the airfoil.

  13. Runout distance and dynamic pressure of pyroclastic density currents: Evidence from 18 May 1980 blast surge of Mount St. Helens

    Science.gov (United States)

    Gardner, J. E.; Andrews, B. J.

    2016-12-01

    Pyroclastic density currents (flows and surges) are one of the most deadly hazards associated with volcanic eruptions. Understanding what controls how far such currents will travel, and how their dynamic pressure evolves, could help mitigate their hazards. The distance a ground hugging, pyroclastic density current travels is partly limited by when it reverses buoyancy and lifts off into the atmosphere. The 1980 blast surge of Mount St. Helens offers an example of a current seen to lift off. Before lofting, it had traveled up to 20 km and leveled more than 600 km3 of thick forest (the blowdown zone). The outer edge of the devastated area - where burned trees that were left standing (the singe zone) - is where the surge is thought to have lifted off. We recently examined deposits in the outer parts of the blowdown and in the singe zone at 32 sites. The important finding is that the laterally moving surge travelled into the singe zone, and hence the change in tree damage does not mark the run out distance of the ground hugging surge. Eyewitness accounts and impacts on trees and vehicles reveal that the surge consisted of a fast, dilute "overcurrent" and a slower "undercurrent", where most of the mass (and heat) was retained. Reasonable estimates for flow density and velocity show that dynamic pressure of the surge (i.e., its ability to topple trees) peaked near the base of the overcurrent. We propose that when the overcurrent began to lift off, the height of peak dynamic pressure rose above the trees and stopped toppling them. The slower undercurrent continued forward, burning trees but it lacked the dynamic pressure needed to topple them. Grain-size variations argue that it slowed from 30 m/s when it entered the singe zone to 3 m/s at the far end. Buoyancy reversal and liftoff are thus not preserved in the deposits where the surge lofted upwards.

  14. Thermal stability assessment of antibiotics in moderate temperature and subcriticalwater using a pressurized dynamic flow-through system

    OpenAIRE

    Svahn, Ola; Björklund, Erland

    2015-01-01

    Thermal degradation of antibiotics has been studied for decades in a broad range of disciplines including food production, agriculture and analytical chemistry. Yet, there is a lack of thermal stability data for many antibiotics. Here we systematically investigated the thermal stability of ten commonly prescribed antibiotics applying a laborsaving automated inhouse pressurized dynamic flow-through system. The design of the system allowed a fast access to a large number of data at medium to su...

  15. Effects of temperature and pressure on the nucleation and growth of silver clusters from supersaturated vapor: A molecular dynamics analysis

    Science.gov (United States)

    Wang, Qin; Xie, Hui; Chen, Yongshi; Liu, Chao

    2017-04-01

    The nucleation and growth of silver nanoparticles in the supersaturated system are investigated by molecular dynamics simulation at different temperatures and pressures. The variety of the atoms in the biggest cluster and the size of average clusters in the system versus the time are estimated to reveal the relationship between the nucleation as well as cluster growth. The nucleation rates in different situations are calculated with the threshold method. The effect of temperature and pressure on the nucleation rate is identified as obeying a linear function. Finally, the development of basal elements, such as monomers, dimers and trimmers, is revealed how the temperature and pressure affect the nucleation and growth of the silver cluster.

  16. Vapor pressures and heats of sublimation of crystalline β-cellobiose from classical molecular dynamics simulations with quantum mechanical corrections.

    Science.gov (United States)

    Wohlert, Jakob

    2014-05-22

    In this paper, we report the calculation of the enthalpy of sublimation, Δ(sub)H, as a function of temperature of crystalline β-cellobiose from molecular dynamics (MD) simulations, using two popular carbohydrate force fields. Together with the entropy difference between the solid and the vapor, ΔS, evaluated at atmospheric pressure, Δ(sub)H gives the vapor pressure of cellobiose over the solid phase as a function of T. It is found that when quantum mechanical corrections to the enthalpy calculated from the distribution of normal modes is applied both force fields give Δ(sub)H close to experiments. The entropy change, ΔS, which is calculated within a harmonic approximation becomes too small, leading to vapor pressures that are too low. These findings are relevant to MD simulations of crystalline carbohydrates in general, e.g., native cellulose.

  17. Quantitative Imaging of Turbulent Mixing Dynamics in High-Pressure Fuel Injection to Enable Predictive Simulations of Engine Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Frank, Jonathan H. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Reacting Flows Dept.; Pickett, Lyle M. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Engine Combustion Dept.; Bisson, Scott E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Remote Sensing and Energetic Materials Dept.; Patterson, Brian D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). combustion Chemistry Dept.; Ruggles, Adam J. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Reacting Flows Dept.; Skeen, Scott A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Engine Combustion Dept.; Manin, Julien Luc [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Engine Combustion Dept.; Huang, Erxiong [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Reacting Flows Dept.; Cicone, Dave J. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Engine Combustion Dept.; Sphicas, Panos [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Engine Combustion Dept.

    2015-09-01

    In this LDRD project, we developed a capability for quantitative high - speed imaging measurements of high - pressure fuel injection dynamics to advance understanding of turbulent mixing in transcritical flows, ignition, and flame stabilization mechanisms, and to provide e ssential validation data for developing predictive tools for engine combustion simulations. Advanced, fuel - efficient engine technologies rely on fuel injection into a high - pressure, high - temperature environment for mixture preparation and com bustion. Howe ver, the dynamics of fuel injection are not well understood and pose significant experimental and modeling challenges. To address the need for quantitative high - speed measurements, we developed a Nd:YAG laser that provides a 5ms burst of pulses at 100 kHz o n a robust mobile platform . Using this laser, we demonstrated s patially and temporally resolved Rayleigh scattering imaging and particle image velocimetry measurements of turbulent mixing in high - pressure gas - phase flows and vaporizing sprays . Quantitativ e interpretation of high - pressure measurements was advanced by reducing and correcting interferences and imaging artifacts.

  18. Where do winds come from? A new theory on how water vapor condensation influences atmospheric pressure and dynamics

    Directory of Open Access Journals (Sweden)

    A. M. Makarieva

    2010-10-01

    Full Text Available Phase transitions of atmospheric water play a ubiquitous role in the Earth's climate system, but their direct impact on atmospheric dynamics has escaped wide attention. Here we examine and advance a theory as to how condensation influences atmospheric pressure through the mass removal of water from the gas phase with a simultaneous account of the latent heat release. Building from fundamental physical principles we show that condensation is associated with a decline in air pressure in the lower atmosphere. This decline occurs up to a certain height, which ranges from 3 to 4 km for surface temperatures from 10 to 30 °C. We then estimate the horizontal pressure differences associated with water vapor condensation and find that these are comparable in magnitude with the pressure differences driving observed circulation patterns. The water vapor delivered to the atmosphere via evaporation represents a store of potential energy available to accelerate air and thus drive winds. Our estimates suggest that the global mean power at which this potential energy is released by condensation is around one per cent of the global solar power – this is similar to the known stationary dissipative power of general atmospheric circulation. We conclude that condensation and evaporation merit attention as major, if previously overlooked, factors in driving atmospheric dynamics.

  19. The dynamic pressure response to rapid dilatation of the resting urethra in healthy women

    DEFF Research Database (Denmark)

    Bagi, P; Thind, P; Colstrup, H;

    1993-01-01

    beta e-t/tau beta, where Pequ, P alpha and P beta are constants, and tau alpha and tau beta are time constants; this equation has previously been demonstrated to describe the pressure decay following dilatation. On the basis of a theoretical model the elastic and viscous constants for the urethral...... tissues were computed. The results showed significant differences along the urethra, with the high-pressure zone showing the highest maximum and equilibrium pressures, fastest pressure decay and highest elastic coefficient. The pressure response represents an integrated stress response from...... the surrounding structures, which reflects the visco-elastic properties of the tissues involved. The findings seem therefore to correlate well with the anatomical findings, which have shown a high fibre density of the horseshoe-shaped rhabdosphincter in the mid-portion of the urethra. The method permits...

  20. Intraocular pressure and ocular pulse amplitude using dynamic contour tonometry and contact lens tonometry

    Directory of Open Access Journals (Sweden)

    Grus Franz-H

    2004-03-01

    Full Text Available Abstract Background The new Ocular Dynamic Contour Tonometer (DCT, investigational device supplied by SMT (Swiss Microtechnology AG, Switzerland allows simultaneous recording of intraocular pressure (IOP and ocular pulse amplitude (OPA. It was the aim of this study to compare the IOP results of this new device with Goldmann tonometry. Furthermore, IOP and OPA measured with the new slitlamp-mounted DCT were compared to the IOP and OPA measured with the hand-held SmartLens®, a gonioscopic contact lens tonometer (ODC Ophthalmic Development Company AG, Switzerland. Methods Nineteen healthy subjects were included in this study. IOP was determined by three consecutive measurements with each of the DCT, SmartLens®, and Goldmann tonometer. Furthermore, OPA was measured three times consecutively by DCT and SmartLens®. Results No difference (P = 0.09 was found between the IOP values by means of DCT (mean: 16.6 mm Hg, median: 15.33 mm Hg, SD: +/- 4.04 mm Hg and Goldmann tonometry (mean: 16.17 mm Hg, median: 15.33 mm Hg, SD: +/- 4.03 mm Hg. The IOP values of SmartLens® (mean: 20.25 mm Hg, median: 19.00 mm Hg, SD: +/- 4.96 mm Hg were significantly higher (P = 0.0008 both from Goldmann tonometry and DCT. The OPA values of the DCT (mean: 3.08 mm Hg, SD: +/- 0.92 mm Hg were significantly lower (P = 0.0003 than those obtained by SmartLens® (mean: 3.92 mm Hg, SD: +/- 0.83 mm Hg. Conclusions DCT was equivalent to Goldmann applanation tonometry in measurement of IOP in a small group of normal subjects. In contrast, SmartLens® (contact lens tonometry gave IOP readings that were significantly higher compared with Goldmann applanation tonometer readings. Both devices, DCT and SmartLens® provide the measurement of OPA which could be helpful e.g. for the management of glaucoma.

  1. Acute pressure on the sciatic nerve results in rapid inhibition of the wide dynamic range neuronal response

    Science.gov (United States)

    2012-01-01

    Background Acute pressure on the sciatic nerve has recently been reported to provide rapid short-term relief of pain in patients with various pathologies. Wide dynamic range (WDR) neurons transmit nociceptive information from the dorsal horn to higher brain centers. In the present study, we examined the effect of a 2-min application of sciatic nerve pressure on WDR neuronal activity in anesthetized male Sprague–Dawley rats. Results Experiments were carried out on 41 male Sprague–Dawley albino rats weighing 160–280 grams. Dorsal horn WDR neurons were identified on the basis of characteristic responses to mechanical stimuli applied to the cutaneous receptive field. Acute pressure was applied for 2 min to the sciatic nerve using a small vascular clip. The responses of WDR neurons to three mechanical stimuli applied to the cutaneous receptive field were recorded before, and 2, 5 and 20 min after cessation of the 2-min pressure application on the sciatic nerve. Two-min pressure applied to the sciatic nerve caused rapid attenuation of the WDR response to pinching, pressure and brushing stimuli applied to the cutaneous receptive field. Maximal attenuation of the WDR response to pinching and pressure was noted 5 min after release of the 2-min pressure on the sciatic nerve. The mean firing rate decreased from 31.7±1.7 Hz to 13±1.4 Hz upon pinching (p < 0.001), from 31.2±2.3 Hz to 10.9±1.4 Hz (p < 0.001) when pressure was applied, and from 18.9±1.2 Hz to 7.6±1.1 Hz (p < 0.001) upon brushing. Thereafter, the mean firing rates gradually recovered. Conclusions Our results indicate that acute pressure applied to the sciatic nerve exerts a rapid inhibitory effect on the WDR response to both noxious and innocuous stimuli. Our results may partially explain the rapid analgesic effect of acute sciatic nerve pressure noted in clinical studies, and also suggest a new model for the study of pain. PMID:23211003

  2. Quantifying dynamic changes in plantar pressure gradient in diabetics with peripheral neuropathy

    Directory of Open Access Journals (Sweden)

    Chi-Wen Lung

    2016-07-01

    Full Text Available Diabetic foot ulcers remain one of the most serious complications of diabetes. Peak plantar pressure (PPP and peak pressure gradient (PPG during walking have been shown to be associated with the development of diabetic foot ulcers. To gain further insight into the mechanical etiology of diabetic foot ulcers, examination of the pressure gradient angle (PGA has been recently proposed. The PGA quantifies directional variation or orientation of the pressure gradient during walking, and provides a measure of whether pressure gradient patterns are concentrated or dispersed along the plantar surface. We hypothesized that diabetics at risk of foot ulceration would have smaller PGA in key plantar regions, suggesting less movement of the pressure gradient over time. A total of 27 participants were studied, including 19 diabetics with peripheral neuropathy and 8 non-diabetic control subjects. A foot pressure measurement system was used to measure plantar pressures during walking. PPP, PPG and PGA were calculated for four foot regions - 1st toe (T1, 1st metatarsal head (M1, 2nd metatarsal head (M2, and heel (HL. Consistent with prior studies, PPP and PPG were significantly larger in the diabetic group compared to non-diabetic controls in the T1 and M1 regions, but not M2 or HL. For example, PPP was 165% (P=0.02 and PPG was 214% (P<0.001 larger in T1. PGA was found to be significantly smaller in the diabetic group in T1 (46%, P=0.04, suggesting a more concentrated pressure gradient pattern under the toe. The proposed PGA may improve our understanding of the role of pressure gradient on the risk of diabetic foot ulcers.

  3. Quantifying Dynamic Changes in Plantar Pressure Gradient in Diabetics with Peripheral Neuropathy

    Science.gov (United States)

    Lung, Chi-Wen; Hsiao-Wecksler, Elizabeth T.; Burns, Stephanie; Lin, Fang; Jan, Yih-Kuen

    2016-01-01

    Diabetic foot ulcers remain one of the most serious complications of diabetes. Peak plantar pressure (PPP) and peak pressure gradient (PPG) during walking have been shown to be associated with the development of diabetic foot ulcers. To gain further insight into the mechanical etiology of diabetic foot ulcers, examination of the pressure gradient angle (PGA) has been recently proposed. The PGA quantifies directional variation or orientation of the pressure gradient during walking and provides a measure of whether pressure gradient patterns are concentrated or dispersed along the plantar surface. We hypothesized that diabetics at risk of foot ulceration would have smaller PGA in key plantar regions, suggesting less movement of the pressure gradient over time. A total of 27 participants were studied, including 19 diabetics with peripheral neuropathy and 8 non-diabetic control subjects. A foot pressure measurement system was used to measure plantar pressures during walking. PPP, PPG, and PGA were calculated for four foot regions – first toe (T1), first metatarsal head (M1), second metatarsal head (M2), and heel (HL). Consistent with prior studies, PPP and PPG were significantly larger in the diabetic group compared with non-diabetic controls in the T1 and M1 regions, but not M2 or HL. For example, PPP was 165% (P = 0.02) and PPG was 214% (P < 0.001) larger in T1. PGA was found to be significantly smaller in the diabetic group in T1 (46%, P = 0.04), suggesting a more concentrated pressure gradient pattern under the toe. The proposed PGA may improve our understanding of the role of pressure gradient on the risk of diabetic foot ulcers. PMID:27486576

  4. Dynamic Characteristics of Mechanical Ventilation System of Double Lungs with Bi-Level Positive Airway Pressure Model

    Directory of Open Access Journals (Sweden)

    Dongkai Shen

    2016-01-01

    Full Text Available In recent studies on the dynamic characteristics of ventilation system, it was considered that human had only one lung, and the coupling effect of double lungs on the air flow can not be illustrated, which has been in regard to be vital to life support of patients. In this article, to illustrate coupling effect of double lungs on flow dynamics of mechanical ventilation system, a mathematical model of a mechanical ventilation system, which consists of double lungs and a bi-level positive airway pressure (BIPAP controlled ventilator, was proposed. To verify the mathematical model, a prototype of BIPAP system with a double-lung simulators and a BIPAP ventilator was set up for experimental study. Lastly, the study on the influences of key parameters of BIPAP system on dynamic characteristics was carried out. The study can be referred to in the development of research on BIPAP ventilation treatment and real respiratory diagnostics.

  5. Constraining the dynamical importance of hot gas and radiation pressure in quasar outflows using emission line ratios

    CERN Document Server

    Stern, Jonathan; Zakamska, Nadia L; Hennawi, Joseph F

    2015-01-01

    Quasar feedback models often predict an expanding hot gas bubble which drives a galaxy-scale outflow. In many circumstances the hot gas is predicted to radiate inefficiently, making the hot bubble hard to observe directly. We present an indirect method to detect the presence of a hot bubble using hydrostatic photoionization models of the cold (10^4 K) line-emitting gas. These models assume that the cold gas is in pressure equilibrium with either the hot gas pressure or with the radiation pressure, whichever is larger. We compare our models with observations of the broad line region (BLR), the inner face of the dusty torus, the narrow line region (NLR), and the extended NLR, and thus constrain the hot gas pressure over a dynamical range of 10^5 in radius, from 0.1 pc to 10 kpc. We find that the emission line ratios observed in the average quasar spectrum are consistent with radiation-pressure-dominated models on all scales. On scales > L_AGN/c inferred for galaxy-scale outflows in luminous quasars. This appare...

  6. Coupling of temperature with pressure induced initial decomposition mechanisms of two molecular crystals: An ab initio molecular dynamics study

    Indian Academy of Sciences (India)

    QIONG WU; DONG XIANG; GUOLIN XIONG; WEIHUA ZHU; HEMING XIAO

    2016-05-01

    Ab initio molecular dynamics simulations were performed to study the initiation of decompositionand formation of first products of two molecular crystals pentaerythritol tetranitrate (PETN) and 5-nitro-2,4-dihydro-1,2,4-triazole-3-one (NTO) under thermal decomposition temperature (475 K for PETN and 531 Kfor NTO) coupled with different pressures (1-5 GPa). The pressure effects on the initial decomposition stepsand initially generated products on PETN and NTO were very different. PETN was triggered by C-H... O intermolecular hydrogen transfer. The initial decomposition mechanism was independent of the pressure. ForNTO, two different initial decomposition mechanisms were found. At 1, 2, and 3 GPa, it was triggered by NH....O intermolecular hydrogen transfer, while at 4 and 5 GPa, it was triggered by N-H.....N intermolecularhydrogen transfer. This indicates that the initial decomposition mechanism was dependent on the pressure.Our study may provide new insights into initial mechanisms and decomposition reactions of molecular crystalexplosives under thermal decomposition temperature coupled with different pressures with details at atomiclevel.

  7. Water content dynamics at plot scale - comparison of time-lapse electrical resistivity tomography monitoring and pore pressure modelling

    Science.gov (United States)

    Zieher, Thomas; Markart, Gerhard; Ottowitz, David; Römer, Alexander; Rutzinger, Martin; Meißl, Gertraud; Geitner, Clemens

    2017-01-01

    Physically-based dynamic modelling of shallow landslide susceptibility rests on several assumptions and simplifications. However, the applicability of physically-based models is only rarely tested in the field at the appropriate scale. This paper presents results of a spray irrigation experiment conducted on a plot of 100 m2 on an Alpine slope susceptible to shallow landsliding. Infiltrating precipitation applied at a constant rate (27.5 mm/h for 5.3 h) was monitored by means of 2D time-lapse electrical resistivity tomography, combined with time-domain reflectometry sensors installed at various depths. In addition, regolith characteristics were assessed by dynamic cone penetration tests using a light-weight cone penetrometer. The spray irrigation experiment resulted in a vertically progressing wetting front to a depth of 80-100 cm. Below that, the unconsolidated material was already saturated by rainfall in the previous days. The observed mean resistivity reduction attributed to infiltrating water during irrigation was scaled to pressure head. Mean variations in pore pressure were reproduced by a linear diffusion model also used in physically-based dynamic landslide susceptibility modelling. Sensitive parameters (hydraulic conductivity and specific storage) were tested over selected value ranges and calibrated. Calibrated parameter values are within published and experimentally derived ranges. The results of the comparison of observations and model results suggest that the model is capable of reproducing mean changes of pore pressure at a suitable scale for physically-based modelling of shallow landslide susceptibility. However, small-scale variations in pore pressure that may facilitate the triggering of shallow landslides are not captured by the model.

  8. Synchrotron infrared spectroscopy at megabar pressures - Vibrational dynamics of hydrogen to 180 GPa

    Science.gov (United States)

    Hanfland, M.; Hemley, R. J.; Mao, H. K.; Williams, G. P.

    1992-01-01

    New techniques for measuring infrared spectra at megabar pressures using synchrotron radiation have been developed and applied to study the Q1(1), Qi(1) + Si(0), and QR(J) vibrational transitions of solid hydrogen to 180 GPa. The frequency difference between the Q1(1) infrared and Raman vibrons increases from 3/cm (zero pressure) to 510/cm (180 GPa), indicating a dramatic increase in intermolecular coupling with pressure. A negative frequency shift is observed for the infrared vibron above 140 GPa. A significant increase in frequency and LO-TO splitting of the lattice phonon is also documented.

  9. [Indices of static and dynamic components of pressure load (assessed by 24-hour blood pressure monitoring) and the state of renal function in patients with essential hypertension].

    Science.gov (United States)

    Zelveian, P A; Buniatian, M S; Oshchepkova, E V; Lazareva, N V; Rogoza, A N

    2011-01-01

    Aim of this study was to evaluate possible relationship between parameters of blood pressure (BP) profile and glomerular filtration rate in patients (pts) with I-II stage essential hypertension (EH). Material and methods. We studied 120 pts (97 men), aged 23-65 (50,2+/-0,6) years with I (n=98) and II (n=22) stage EH. In BP profile (SL-90207) we calculated 24-hour, daytime, nighttime values of systolic, diastolic, pulse pressures (SBP, DBP, PP), time load (TL), variability and nocturnal fall (NF) of BP. The state of renal function was assessed by measurement of glomerular filtration rate (GFR) calculated by the Cockcroft formula. Results. After nonlinear statistical analysis by Gauss-Newton all patients were divided into three groups according to GFR tertiles. Significant differences were found between these groups by 24-hour, nighttime and daytime values of SBP and DBP. Values of SBP were the lowest in group II. In group II lowest values of PP were also observed, but statistically significant differences were found only in nocturnal PP values between groups II and III. There were no significant differences between groups by TL and NF of BP. In group Ill (high GFR) variability of daytime values of SBP and DBF were significantly higher. Univariate correlation analysis showed statistically significant negative relationship between GFR and nocturnal PP in patients with lowest level of GFR. Positive correlations between nocturnal values of PP and GFR in groups II and III were also observed. Conclusion. These results indicated the presence of strong relationship between high values of nocturnal PP and decreasing of glomerular filtration rate in patients with EH and thus confirmed significance of "constant" and "dynamic" components of pressure load as a marker of impairment of renal function.

  10. Thermoacoustic analysis of the dynamic pressure inside a model combustor during limit cycle oscillations

    NARCIS (Netherlands)

    Alemela, Panduranga Reddy; Roman Casado, Juan; Tarband Veeraraghavan, Santos Kumar; Kok, Jim

    2013-01-01

    In this work comprehensive experimental and numerical studies incorporating the most relevant physical mechanisms causing limit cycle pressure and combustion rate oscillations (LCO) in a laboratory scale combustor will be discussed. The strong interaction between the aerodynamics-combustion-acoustic

  11. Cerebrospinal fluid pulse pressure and craniospinal dynamics : a theoretical, clinical and experimental study

    NARCIS (Netherlands)

    C.J.J. Avezaat (Cees); J.H.M. van Eijndhoven (Johannes Hubertus Marcellianus)

    1984-01-01

    textabstractSince the introduction of continuous recording of intracranial pressure (ICP) in neurosurgical practice (Guillaume and Janny, 1951; Lundberg, 1960) this method has greatly contributed to clinical research in the field of intracranial hypertension. Numerous publications have enriched the

  12. Prosthetics socket that incorporates an air splint system focusing on dynamic interface pressure

    OpenAIRE

    Razak, Nasrul Anuar Abd; Osman, Noor Azuan Abu; Gholizadeh, Hossein; Ali, Sadeeq

    2014-01-01

    Background The interface pressure between the residual limb and prosthetic socket has a significant effect on an amputee’s satisfaction and comfort. This paper presents the design and performance of a new prosthetic socket that uses an air splint system. Methods The air splint prosthetic socket system was implemented by combining the air splint with a pressure sensor that the transhumeral user controls through the use of a microcontroller. The modular construction of the system developed allo...

  13. Probing of Fast Chemical Dynamics at High Pressures and Temperatures using Pulsed Laser Techniques

    Science.gov (United States)

    2014-12-17

    Goncharov. Hydrogen (deuterium) vibron frequency as a pressure comparison gauge at multi-Mbar pressures, Journal of Applied Physics, (08 2013): 73505...V. Struzhkin, Innokenty Kantor, Mark L. Rivers , D. Allen Dalton. X-ray diffraction in the pulsed laser heated diamond anvil cell, Review of...few-layered two-dimensional MoS2 in collaboration with Avinash Nayak and Professor Jung-Fu Lin at the University of Texas at Austin

  14. Use of dynamic CT in acute respiratory distress syndrome (ARDS) with comparison of positive and negative pressure ventilation

    Energy Technology Data Exchange (ETDEWEB)

    Helm, Emma; Babyn, Paul [Hospital for Sick Children, Department of Diagnostic Imaging, Toronto (Canada); Talakoub, Omid; Alirezaie, Javad [Ryerson University, Department of Electrical and Computer Engineering, Toronto, ON (Canada); Grasso, Francesco; Engelberts, Doreen; Kavanagh, Brian P. [Hospital for Sick Children and the University of Toronto, Departments of Anesthesia and Critical Care Medicine and the Program in Pulmonary and Experimental Medicine, Toronto (Canada)

    2009-01-15

    Negative pressure ventilation via an external device ('iron lung') has the potential to provide better oxygenation with reduced barotrauma in patients with ARDS. This study was designed to see if oxygenation differences between positive and negative ventilation could be explained by CT. Six anaesthetized rabbits had ARDS induced by repeated saline lavage. Rabbits were ventilated with positive pressure ventilation (PPV) and negative pressure ventilation (NPV) in turn. Dynamic CT images were acquired over the respiratory cycle. A computer-aided method was used to segment the lung and calculate the range of CT densities within each slice. Volumes of ventilated lung and atelectatic lung were measured over the respiratory cycle. NPV was associated with an increased percentage of ventilated lung and decreased percentage of atelectatic lung. The most significant differences in ventilation and atelectasis were seen at mid-inspiration and mid-expiration (ventilated lung NPV=61%, ventilated lung PPV=47%, p<0.001; atelectatic lung NPV=10%, atelectatic lung PPV 19%, p<0.001). Aeration differences were not significant at end-inspiration. Dynamic CT can show differences in lung aeration between positive and negative ventilation in ARDS. These differences would not be appreciated if only static breath-hold CT was used. (orig.)

  15. A physical framework for implementing virtual models of intracranial pressure and cerebrospinal fluid dynamics in hydrocephalus shunt testing.

    Science.gov (United States)

    Venkataraman, Pranav; Browd, Samuel R; Lutz, Barry R

    2016-09-01

    OBJECTIVE The surgical placement of a shunt designed to resolve the brain's impaired ability to drain excess CSF is one of the most common treatments for hydrocephalus. The use of a dynamic testing platform is an important part of shunt testing that can faithfully reproduce the physiological environment of the implanted shunts. METHODS A simulation-based framework that serves as a proof of concept for enabling the application of virtual intracranial pressure (ICP) and CSF models to a physical shunt-testing system was engineered. This was achieved by designing hardware and software that enabled the application of dynamic model-driven inlet and outlet pressures to a shunt and the subsequent measurement of the resulting drainage rate. RESULTS A set of common physiological scenarios was simulated, including oscillations in ICP due to respiratory and cardiac cycles, changes in baseline ICP due to changes in patient posture, and transient ICP spikes caused by activities such as exercise, coughing, sneezing, and the Valsalva maneuver. The behavior of the Strata valve under a few of these physiological conditions is also demonstrated. CONCLUSIONS Testing shunts with dynamic ICP and CSF simulations can facilitate the optimization of shunts to be more failure resistant and better suited to patient physiology.

  16. A Novel Dynamic Model for Predicting Pressure Wave Velocity in Four-Phase Fluid Flowing along the Drilling Annulus

    Directory of Open Access Journals (Sweden)

    Xiangwei Kong

    2015-01-01

    Full Text Available A dynamic pressure wave velocity model is presented based on momentum equation, mass-balance equation, equation of state, and small perturbation theory. Simultaneously, the drift model was used to analyze the flow characteristics of oil, gas, water, and drilling fluid multiphase flow. In addition, the dynamic model considers the gas dissolution, virtual mass force, drag force, and relative motion of the interphase as well. Finite difference and Newton-Raphson iterative are introduced to the numerical simulation of the dynamic model. The calculation results indicate that the wave velocity is more sensitive to the increase of gas influx rate than the increase of oil/water influx rate. Wave velocity decreases significantly with the increase of gas influx. Influenced by the pressure drop of four-phase fluid flowing along the annulus, wave velocity tends to increase with respect to well depth, contrary to the gradual reduction of gas void fraction at different depths with the increase of backpressure (BP. Analysis also found that the growth of angular frequency will lead to an increase of wave velocity at low range. Comparison with the calculation results without considering virtual mass force demonstrates that the calculated wave velocity is relatively bigger by using the presented model.

  17. The relationships between foot arch volumes and dynamic plantar pressure during midstance of walking in preschool children.

    Directory of Open Access Journals (Sweden)

    Hsun-Wen Chang

    Full Text Available OBJECTIVES: The purpose of this study was to examine the correlation between the foot arch volume measured from static positions and the plantar pressure distribution during walking. METHODS: A total of 27 children, two to six years of age, were included in this study. Measurements of static foot posture were obtained, including navicular height and foot arch volume in sitting and standing positions. Plantar pressure, force and contact areas under ten different regions of the foot were obtained during walking. RESULTS: The foot arch index was correlated (r = 0.32 with the pressure difference under the midfoot during the foot flat phase. The navicular heights and foot arch volumes in sitting and standing positions were correlated with the mean forces and pressures under the first (r = -0.296∼-0.355 and second metatarsals (r = -0.335∼-0.504 and midfoot (r = -0.331∼-0.496 during the stance phase of walking. The contact areas under the foot were correlated with the foot arch parameters, except for the area under the midfoot. CONCLUSIONS: The foot arch index measured in a static position could be a functional index to predict the dynamic foot functions when walking. The foot arch is a factor which will influence the pressure distribution under the foot. Children with a lower foot arch demonstrated higher mean pressure and force under the medial forefoot and midfoot, and lower contact areas under the foot, except for the midfoot region. Therefore, children with flatfoot may shift their body weight to a more medial foot position when walking, and could be at a higher risk of soft tissue injury in this area.

  18. Dynamics of diffusive bubble growth and pressure recovery in a bubbly rhyolitic melt embedded in an elastic solid

    Science.gov (United States)

    Chouet, Bernard A.; Dawson, Phillip B.; Nakano, Masaru

    2006-01-01

    We present a model of gas exsolution and bubble expansion in a melt supersaturated in response to a sudden pressure drop. In our model, the melt contains a suspension of gas bubbles of identical sizes and is encased in a penny-shaped crack embedded in an elastic solid. The suspension is modeled as a three-dimensional lattice of spherical cells with slight overlap, where each elementary cell consists of a gas bubble surrounded by a shell of volatile-rich melt. The melt is then subjected to a step drop in pressure, which induces gas exsolution and bubble expansion, resulting in the compression of the melt and volumetric expansion of the crack. The dynamics of diffusion-driven bubble growth and volumetric crack expansion span 9 decades in time. The model demonstrates that the speed of the crack response depends strongly on volatile diffusivity in the melt and bubble number density and is markedly sensitive to the ratio of crack thickness to crack radius and initial bubble radius but is relatively insensitive to melt viscosity. The net drop in gas concentration in the melt after pressure recovery represents only a small fraction of the initial concentration prior to the drop, suggesting the melt may undergo numerous pressure transients before becoming significantly depleted of gases. The magnitude of pressure and volume recovery in the crack depends sensitively on the size of the input-pressure transient, becoming relatively larger for smaller-size transients in a melt containing bubbles with initial radii less than 10-5 m. Amplification of the input transient may be large enough to disrupt the crack wall and induce brittle failure in the rock matrix surrounding the crack. Our results provide additional basis for the interpretation of volume changes in the magma conduit under Popocatépetl Volcano during Vulcanian degassing bursts in its eruptive activity in April–May 2000.

  19. Vortex dynamics and surface pressure fluctuations on a normal flat plate

    Science.gov (United States)

    Hemmati, Arman; Wood, David H.; Martinuzzi, Robert J.; Ferrari, Simon W.; Hu, Yaoping

    2016-11-01

    The effect of vortex formation and interactions on surface pressure fluctuations is examined in the wake of a normal flat plate by analyzing Direct Numerical Simulations at Re =1200. A novel local maximum score-based 3D method is used to track vortex development in the region close to the plate where the major contributions to the surface pressure are generated. Three distinct vortex shedding regimes are identified by changes in the lift and drag fluctuations. The instances of maximum drag coincide with impingement of newly formed vortices on the plate. This results in large and concentrated areas of rotational and strain contributions to generation of pressure fluctuations. Streamwise vortex straining and chordwise stretching are correlated with the large ratios of streamwise to chordwise normal stresses and regions of significant rotational contribution to the pressure. In contrast at the minimum drag, the vorticity field close to the plate is disorganized, and vortex roll-up occurs farther downstream. This leads to a uniform distribution of pressure. This study was supported by Alberta Innovates Technology Futures (AITF) and Natural Sciences and Engineering Research Council of Canada (NSERC).

  20. Dynamic plantar pressure distribution, strength capacity and postural control after Lisfranc fracture-dislocation

    DEFF Research Database (Denmark)

    Mehlhorn, Alexander T; Walther, Markus; Yilmaz, Tayfun

    2017-01-01

    of life. 17 consecutive patients suffering from a Lisfranc fracture dislocation were registered, underwent open reduction and internal fixation and were followed-up for 50.5±25.7months (Mean±SDM). Biomechanical analysis of muscle strength capacities, postural control and plantar pressure distribution...... correlated well with clinical outcome. Altered postural control was evident by a significant reduction in unilateral stance time, from which we calculated a strong correlation between stance time and the isokinetic strength measurement. Plantar pressure measurements revealed a significant reduction in peak...... pressure under the midfoot and of Force-Time Integral beneath the second metatarsal. Sufficient rehabilitation is crucial to the clinical outcome following anatomical open reduction of Lisfranc fracture-dislocation. The present study supports a rehabilitation approach focussing on restoring proprioception...

  1. Computational fluid dynamics modelling of cerebrospinal fluid pressure in Chiari malformation and syringomyelia.

    Science.gov (United States)

    Clarke, Elizabeth C; Fletcher, David F; Stoodley, Marcus A; Bilston, Lynne E

    2013-07-26

    The pathogenesis of syringomyelia in association with Chiari malformation (CM) is unclear. Studies of patients with CM have shown alterations in the CSF velocity profile and these could contribute to syrinx development or enlargement. Few studies have considered the fluid mechanics of CM patients with and without syringomyelia separately. Three subject-specific CFD models were developed for a normal participant, a CM patient with syringomyelia and a CM patient without syringomyelia. Model geometries, CSF flow rate data and CSF velocity validation data were collected from MRI scans of the 3 subjects. The predicted peak CSF pressure was compared for the 3 models. An extension of the study performed geometry and flow substitution to investigate the relative effects of anatomy and CSF flow profile on resulting spinal CSF pressure. Based on 50 monitoring locations for each of the models, the CM models had significantly higher magnitude (psyringomyelia mechanisms and relative effects of CSF velocity profile and spinal geometry on CSF pressure.

  2. Numerical simulation of magnetospheric ULF waves excited by positive and negative impulses of solar wind dynamic pressure

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The sources of ultra low frequency (ULF) waves in the magnetosphere are generally believed to be either the external solar wind perturbations or the internal plasma instabilities. When a sudden impulse of the solar wind dynamic pressure impinges on the magnetopause, ULF waves might be excited and thus the solar wind energy is transported into the earth’s magnetosphere. In this paper, we study the ULF waves excited by different kinds of sudden solar wind pressure impulses through an MHD simulation. We primarily focus on the responses of the earth’s magnetosphere to positive/negative impulses of solar wind dynamic pressure, and positive-negative impulse pairs. The simulation results show that the ULF waves excited by positive and negative impulse have the same amplitude and frequency, with 180° difference in phase, if the amplitude and durations of the input impulses are the same. In addition, it is found that field line resonances (FLRs) occur at certain L-shell regions of the earth’s magneto-sphere after the impact of different positive-negative impulse pairs, which appear to be related to the duration of the impulses and the time interval between the sequential impulses. Another result is that the energy from the solar wind could be transported deeper into the inner magnetosphere by an impulse pair than by a single pulse impact. The results presented in this paper could help us to better understand how energy is transported from solar wind to the earth’s magnetosphere via ULF waves. Also, these results provide some new clues to understanding of how energetic particles in the inner magnetosphere response to different kinds of solar wind pressure impulse impacts including inter-planetary shocks.

  3. Micro-Structured Sapphire Fiber Sensors for Simultaneous Measurements of High-T and Dynamic Gas Pressure in Harsh Environments

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Hai [Clemson Univ., SC (United States); Tsai, Hai-Lung [Missouri Univ. of Science and Technology, Rolla, MO (United States); Dong, Junhang [Univ. of Cincinnati, OH (United States)

    2014-09-30

    This is the final report for the program “Micro-Structured Sapphire Fiber Sensors for Simultaneous Measurements of High Temperature and Dynamic Gas Pressure in Harsh Environments”, funded by NETL, and performed by Missouri University of Science and Technology, Clemson University and University of Cincinnati from October 1, 2009 to September 30, 2014. Securing a sustainable energy economy by developing affordable and clean energy from coal and other fossil fuels is a central element to the mission of The U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL). To further this mission, NETL funds research and development of novel sensor technologies that can function under the extreme operating conditions often found in advanced power systems. The main objective of this research program is to conduct fundamental and applied research that will lead to successful development and demonstration of robust, multiplexed, microstructured silica and single-crystal sapphire fiber sensors to be deployed into the hot zones of advanced power and fuel systems for simultaneous measurements of high temperature and gas pressure. The specific objectives of this research program include: 1) Design, fabrication and demonstration of multiplexed, robust silica and sapphire fiber temperature and dynamic gas pressure sensors that can survive and maintain fully operational in high-temperature harsh environments. 2) Development and demonstration of a novel method to demodulate the multiplexed interferograms for simultaneous measurements of temperature and gas pressure in harsh environments. 3) Development and demonstration of novel sapphire fiber cladding and low numerical aperture (NA) excitation techniques to assure high signal integrity and sensor robustness.

  4. Dynamics of epidemic spreading with vaccination: Impact of social pressure and engagement

    Science.gov (United States)

    Pires, Marcelo A.; Crokidakis, Nuno

    2017-02-01

    In this work we consider a model of epidemic spreading coupled with an opinion dynamics in a fully-connected population. Regarding the opinion dynamics, the individuals may be in two distinct states, namely in favor or against a vaccination campaign. Individuals against the vaccination follow a standard SIS model, whereas the pro-vaccine individuals can also be in a third compartment, namely Vaccinated. In addition, the opinions change according to the majority-rule dynamics in groups with three individuals. We also consider that the vaccine can give permanent or temporary immunization to the individuals. By means of analytical calculations and computer simulations, we show that the opinion dynamics can drastically affect the disease propagation, and that the engagement of the pro-vaccine individuals can be crucial for stopping the epidemic spreading. The full numerical code for simulating the model is available from the authors' webpage.

  5. Dynamics of epidemic spreading with vaccination: impact of social pressure and engagement

    CERN Document Server

    Pires, Marcelo A

    2016-01-01

    In this work we consider a model of epidemic spreading coupled with an opinion dynamics in a fully-connected population. Regarding the opinion dynamics, the individuals may be in two distinct states, namely in favor or against a vaccination campaign. Individuals against the vaccination follow a standard SIS model, whereas the pro-vaccine individuals can also be in a third compartment, namely Vaccinated. In addition, the opinions change according to the majority-rule dynamics in groups with three individuals. We also consider that the vaccine can give permanent or temporary immunization to the individuals. By means of analytical calculations and computer simulations, we show that the opinion dynamics can drastically affect the disease propagation, and that the engagement of the pro-vaccine individuals can be crucial for stopping the epidemic spreading.

  6. The dynamic spreading of nanofluids on solid surfaces - Role of the nanofilm structural disjoining pressure.

    Science.gov (United States)

    Lim, Sangwook; Zhang, Hua; Wu, Pingkeng; Nikolov, Alex; Wasan, Darsh

    2016-05-15

    Nanofluids comprising nanoparticle suspensions in liquids have significant industrial applications. Prior work performed in our laboratory on the spreading of an aqueous film containing nanoparticles displacing an oil droplet has clearly revealed that the structural disjoining pressure arises due to the layering of the nanoparticles normal to the confining plane of the film with the wedge profile. The pressure drives the nanofluid in the wedge film and the nanofluid spreads. We observed two distinct contact lines: the inner contact line, where the structural disjoining pressure dominates the Laplace capillary pressure, and the outer contact line, given by the Laplace equation prediction extrapolated to the solid substrate where the structural disjoining pressure contribution is negligible. We report here our results of the effects of several parameters, such as the nanoparticle concentration, liquid salinity, temperature, and the substrate contact angle, on the motion of the two contact lines and their effects on the detachment of the oil droplet. We also studied the equilibrated and non-equilibrated oil/nanofluid phases, the time of adhesion of the oil droplet on the solid substrate and the drying time of the substrate. We employed the frictional model to predict the outer contact line velocity and our previous theoretical model (based on the structural disjoining pressure) to predict the inner contact line velocity. The theoretical predictions agreed quite well with the experimentally measured values of the velocities. Our experimental results showed that the motion of the inner contact line was accelerated by the increase in the nanoparticle concentration, temperature, and hydrophilicity of the substrate for the pre-equilibrated oil/nanofluid phases, which resulted in the faster detachment of the oil droplet. The speed of the two contact lines decreased upon the increase in the drying time of the substrate and the oil adhesion time on the substrate. The present

  7. Decreasing deer browsing pressure influenced understory vegetation dynamics over 30 years

    OpenAIRE

    Boulanger, Vincent; Baltzinger, Christophe; Saïd, Sonia; Ballon, Philippe; Picard, Jean-Francois; Dupouey, Jean-Luc

    2015-01-01

    Key message Thanks to the concomitant recordings of vegetation and deer browsing sampled first in 1976, then resurveyed in 2006, we show that forest plant communities shifted in response to deer population dynamics, stand management and eutrophication. Context and aims High deer populations alter forest under-story dynamics worldwide. However, no study ever attempted to rank the importance of deer herbivory relatively to other environmental drivers. In the Arc-en-Barrois National Forest (...

  8. Mechanical properties of reactor pressure vessel steels studied by static and dynamic torsion tests

    Science.gov (United States)

    Munier, A.; Maamouri, M.; Schaller, R.; Mercier, O.

    1993-06-01

    Internal friction measurements and torsional plastic deformation tests have been performed in reactor pressure vessel steels (unirradiated, irradiated and irradiated/annealed specimens). The results of these experiments have been interpreted with help of transmission electron microscopy observations (conventional and in situ). It is shown how the interactions between screw dislocations and obstacles (Peierls valleys, impurities and precipitates) could explain the low temperature hardening and the irradiation embrittlement of ferritic steels. In addition, it appears that the nondestructive internal friction technique could be used advantageously to follow the evolution of the material properties under irradiation, as for instance the irradiation embrittlement of the reactor pressure vessel steels.

  9. Dynamic characteristics research of the pressure reducing valve based on AMESim

    Science.gov (United States)

    Wang, Weihui; Zhang, Peiyi

    2017-05-01

    Through the analysis of the structure and working principle of pressure reducing valve, using AMESim software to model, simulate and analyze its working conditions On the basis of the analysis of the structural parameters of the valve: damping hole diameter D, analog load damping hole diameter D1, spring stiffness K and initial opening S 0f analog load, such as which has the impact of hydraulic pressure reducing valve Finally, the influence of the above parameters on the accuracy of the valve is analyzed, which provides a reference for the design of the valve.

  10. [Prospects of intraoperative dynamic cholangio-manometry by tensor detectors with graphic recording of pressure function].

    Science.gov (United States)

    Tsatsanidi, K N; Pugaev, A V; Gordeev, P S; Sandrikov, V A; Mukha, A V; Gambarian, A R

    1991-02-01

    Intraoperative cholangio-manometry with a miniature tensor sensor and graphic recording of the results were conducted to study the function of the major duodenal papilla in 53 patients. A periodical activity of the ampulla of the papilla was revealed, which was characterized by certain values of the peak and basal pressure, and duration of contraction and relaxation periods. The numerical values and the pattern of the pressure curve differed in patients with obstructive cholecystitis, biliary pancreatitis, and a concrement incarcerated in the ampulla of the papilla. The informativeness of the study increases with the use of the glucagon test.

  11. Numerical investigation of vibration and dynamic pressure of a vertical axis wind turbine

    Directory of Open Access Journals (Sweden)

    F Erchiqui

    2016-10-01

    Full Text Available In the environmental field, the problems of noise reduction have become a major preoccupation, particularly on the noise generated by the acoustic radiation pressure produced by wind turbines. This paper is aimed at presenting the investigation on the application of variational indirect boundary element method for study the acoustic radiation pressure produced by vertical-axis wind turbine. For this initiative, we considered Neumann boundary condition. The formulation has two advantages: the first one is to avoid the meshing of the fluid domain; the second advantage is to treat the singular integral of the Green's function, solution of fundamental solution of the wave equation in frequency domain.

  12. The Grüneisen Parameter of NaCl at High Pressures and Temperatures: a Molecular Dynamics Study

    Institute of Scientific and Technical Information of China (English)

    CAI Ling-Cang; CHEN Qi-Feng; CUI Shou-Xin; JING Fu-Qian

    2005-01-01

    @@ The isotherms and Griineisen parameters are calculated by using the molecular dynamics (MD) method with an improved Tosi-Fumi pair potential. The results show that the approximate power law dependence of the Griineisen parameter on compression γ = γo( V/Vo )q, with q ≈ 1.078, holds in the temperature range from 298 to 1073K and pressure range from 0 to 60 GPa, and that the Griineisen parameter for a given density of 2.16g/cm3varies with temperature in a wind range from 300 to 10000K, expressed by γ = 1.052 + 0.582exp(-T/4878.56).

  13. A numerical study of two-phase flow with dynamic capillary pressure using an adaptive moving mesh method

    CERN Document Server

    Zhang, Hong

    2016-01-01

    Motivated by observations of saturation overshoot, this paper investigates numerical modeling of two-phase flow incorporating dynamic capillary pressure. The effects of the dynamic capillary coefficient, the infiltrating flux rate and the initial and boundary values are systematically studied using a travelling wave ansatz and efficient numerical methods. The travelling wave solutions may exhibit monotonic, non-monotonic or plateau-shaped behaviour. Special attention is paid to the non-monotonic profiles. The travelling wave results are confirmed by numerically solving the partial differential equation using an accurate adaptive moving mesh solver. Comparisons between the computed solutions using the Brooks-Corey model and the laboratory measurements of saturation overshoot verify the effectiveness of our approach.

  14. A pipe network simulation model with dynamic transition between free surface and pressurized flow

    Directory of Open Access Journals (Sweden)

    J. Fernández-Pato

    2014-01-01

    Full Text Available Water flow numerical simulation in urban pipe systems is one of the topics that shows the need for surface flows and pressurized flows in steady and transient situations. The governing equations for both flow types are different and this must be taken into account in order to get a complete numerical model for solving transients. A numerical simulation model is developed in this work, capable of solving pipe networks mainly unpressurized, with isolated peaks of pressurization. For this purpose, a reformulation of the mathematical model through the Preissmann slot method is proposed. By means of this technique, a reasonable estimation of the water pressure is calculated in cases of pressurization. The numerical model is based on the first order Roe's scheme, in the frame of finite volume methods. It is adapted to abrupt transient situations, with subcritial and supercritical flows. The validation has been done by means of several cases with analytic solutions or empirical laboratory data. It has also been applied to some more complex and realistic cases, like junctions or pipe networks.

  15. The Dynamics of Divorce: Marital Quality, Alternative Attractions and External Pressures.

    Science.gov (United States)

    Green, Robert G.; Sporakowski, Michael J.

    1983-01-01

    Tested Lewis and Spanier's theory of marital quality and marital stability using a sample of 131 married and 166 divorced social survey respondents. Examined the relationship between the quality and stability of their marriages and assessed the influence of alternative attractions and external pressures to remain married. (JAC)

  16. Dynamic Testing and Evaluation of Pressure Transducer-Catheter Systems: A Student Project.

    Science.gov (United States)

    Barquest, James M.; Schmalzel, John L.

    Described are four demonstration/participation laboratories in which students analytically and experimentally evaluated various catheter-transducer blood pressure measurement systems. The activities were included in a graduate level course entitled "Theory and Techniques of Bioinstrumentation," taught by the Department of Electrical Engineering…

  17. Experimental Studies of Dynamic Fault Weakening Due to Thermal Pressurization of Pore Fluids

    Science.gov (United States)

    Goldsby, David; Tullis, Terry; Platt, John; Okazaki, Keishi

    2016-04-01

    High-velocity friction experiments and geophysical observations suggest that mature faults weaken dramatically during seismic slip. However, while many coseismic weakening mechanisms have been proposed, it is still unclear which mechanisms are most important or how the efficiency of weakening varies within the seismogenic zone. Thermal pressurization is one possible coseismic weakening mechanism driven by the thermal expansion of native pore fluids, which leads to elevated pore pressures and significant coseismic weakening. While thermal pressurization has been studied theoretically for many decades, and invoked in recent earthquake simulations, its activation in laboratory experiments has remained elusive. Several high-speed friction studies have yielded indirect evidence for thermal pressurization, yet none has directly linked with existing theoretical models or the relevant physical parameters, such as permeability, slip, and slip rate, that control the weakening rate. To fill this gap, we are conducting thermal pressurization experiments on fluid-saturated, low-permeability rocks (Frederick diabase) at slip rates up to ~5 mm/s, at constant confining pressures in the range 21-149 MPa and initial imposed pore pressures in the range 10-25 MPa. The impractically low permeability of the as-is diabase, ~10-23 m2, is increased prior to the test by thermal cracking, yielding measured permeabilities in the range 1.3*10-18 to 6.1*10-19 m2. These values of permeability are high enough to allow sample saturation over one to several days, but low enough to confine the elevated pore pressures generated by frictional heating during rapid sliding. Our experiments reveal a rapid decay of shear stress following a step-change in velocity from 10 μm/s to 4.8 mm/s. In one test, the decrease in shear stress of ~25% over the first 28 mm of slip at 4.8 mm/s agrees closely with the theoretical solution for slip on a plane (Rice [2006]), with an inferred slip-weakening distance of ~500

  18. Development of a sub-scale dynamics model for pressure relaxation of multi-material cells in Lagrangian hydrodynamics

    Directory of Open Access Journals (Sweden)

    Canfield T.R.

    2011-01-01

    Full Text Available We have extended the Sub-Scale Dynamics (SSD closure model for multi-fluid computational cells. Volume exchange between two materials is based on the interface area and a notional interface translation velocity, which is derived from a linearized Riemann solution. We have extended the model to cells with any number of materials, computing pressure-difference-driven volume and energy exchange as the algebraic sum of pairwise interactions. In multiple dimensions, we rely on interface reconstruction to provide interface areas and orientations, and centroids of material polygons. In order to prevent unphysically large or unmanageably small material volumes, we have used a flux-corrected transport (FCT approach to limit the pressure-driven part of the volume exchange. We describe the implementation of this model in two dimensions in the FLAG hydrodynamics code. We also report on Lagrangian test calculations, comparing them with others made using a mixed-zone closure model due to Tipton, and with corresponding calculations made with only single-material cells. We find that in some cases, the SSD model more accurately predicts the state of material in mixed cells. By comparing the algebraic forms of both models, we identify similar dependencies on state and dynamical variables, and propose explanations for the apparent higher fidelity of the SSD model.

  19. Computational fluid dynamic analysis of a closure head penetration in a pressurized water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Forsyth, D.R.; Schwirian, R.E. [Westinghouse Electric Corp., Pittsburgh, PA (United States)

    1995-09-01

    ALLOY 600 has been used typically for penetrations through the closure head in pressurized water reactors because of its thermal compatibility with carbon steel, superior resistance to chloride attack and higher strength than the austenitic stainless steels. Recent plant operating experience with this alloy has indicated that this material may be susceptible to degradation. One of the major parameters relating to degradation of the head penetrations are the operational temperatures and stress levels in the penetration.

  20. Dynamic Response of VVER 1000 Type Reactor Excited by Pressure Pulsations

    OpenAIRE

    Zeman, Vladimír; Hlaváč, Zdeněk

    2008-01-01

    The paper deals with the modelling of forced vibrations of reactor components excited by pressure pulsations generated by main circulation pumps. For the vibration analysis a new generalised model of the reactor with spatial localization of the nuclear fuel assemblies and protection tubes, continuously mass distribution of beam type components and more accurate model of the linear stepper drives for actuation of control cassettes was applied. Slightly different pump revolutions are sources of...

  1. New Techniques for Investigating Properties of Energetic Solids at High Static and Dynamic Pressures.

    Science.gov (United States)

    1976-09-01

    diameter of the sample chamber. Recall that the sample chamber consists of a cylinder in the steel gasket formed by drilling a 0.3 nun diameter hole in...tensile strength of the material, the material undergoes fracture or spallation . B. STRESS WAVE GENERATION AND MEASUREMENT : Stress waves were generated...SAMPLE CHAMBE R OF DIAMOND ANVIL HIGH PRESSURE CELL SAMPLE CHAMBER #79 drill approx. O•369 mm diameter METHANOL— ETHANOL (1:1) BY

  2. Interchain tube pressure effect in the flow dynamics of bi-disperse polymer melts

    DEFF Research Database (Denmark)

    Rasmussen, Henrik K.

    2015-01-01

    The constitutive equation as reported by Rasmussen and Huang (Rheologica Acta 53:199–208, 2014b), explaining the flow dynamics of oligomer (containing a least two Kuhn step)-diluted narrow molecular weight-distributed polymers were extended to general bi-disperse polymer melt system. It was assum...

  3. Patellofemoral Pressure Changes After Static and Dynamic Medial Patellofemoral Ligament Reconstructions

    NARCIS (Netherlands)

    Rood, A.; Hannink, G.; Lenting, A.; Groenen, K.; Koeter, S.; Verdonschot, N.J.; Kampen, A. van

    2015-01-01

    BACKGROUND: Reconstructing the medial patellofemoral ligament (MPFL) has become a key procedure for stabilizing the patella. Different techniques to reconstruct the MPFL have been described: static techniques in which the graft is fixed rigidly to the bone or dynamic techniques with soft tissue fixa

  4. Patellofemoral pressure changes after static and dynamic medial patellofemoral ligament reconstructions

    NARCIS (Netherlands)

    Rood, A.; Hannink, G.; Lenting, A.; Groenen, K.; Koëter, S.; Verdonschot, N.J.J.; Kampen, van A.

    2015-01-01

    Background: Reconstructing the medial patellofemoral ligament (MPFL) has become a key procedure for stabilizing the patella. Different techniques to reconstruct the MPFL have been described: static techniques in which the graft is fixed rigidly to the bone or dynamic techniques with soft tissue fixa

  5. Continuous positive airway pressure alters cranial blood flow and cerebrospinal fluid dynamics at the craniovertebral junction

    Directory of Open Access Journals (Sweden)

    Theresia I. Yiallourou

    2015-09-01

    Conclusion: Application of CPAP via a full-fitted mask at 15 cm H2O was found to have a significant effect on intracranial venous outflow and spinal CSF flow at the C2 vertebral level in healthy adult-age awake volunteers. CPAP can be used to non-invasively provoke changes in intracranial and CSF flow dynamics.

  6. The adsorption of lead(II) ions by dynamic high pressure micro-fluidization treated insoluble soybean dietary fiber.

    Science.gov (United States)

    Wang, Hui; Huang, Tao; Tu, Zong-Cai; Ruan, Chuan-Ying; Lin, Derong

    2016-06-01

    Insoluble dietary fiber from soybean residue (SIDF) was treated with dynamic high-pressure microfluidization (DHPM) and used as adsorbent for Pb(II) ion. The effects of pressure on the Pb(II) adsorption capacity, primary cilia structure and surface topography of SIDF were determined using a gastrointestinal simulated model in vitro. SIDF (at pH 7.0) showed maximum binding capacity (261.42 ± 2.77 μmol/g), which was about 1.13 times higher than that of untreated sample (233.47 ± 1.84 μmol/g), when pressure reached 80 MPa. However, the net adsorption value of SIDF in a simulated small intestine (~ 9 μmol/g) was significantly lower than that in the stomach (~ 48 μmol/g), because of the competitive adsorption of Pb(2+) by pancreatin, cholate and several enzymes in the small intestine. In addition, the adsorption capacity of SIDF exhibited good linear relationship with the physicochemical properties of total negative charges, and the adsorption behavior presumably occurred on the surface area of granules fiber.

  7. Influence of surrounding gas, composition and pressure on plasma plume dynamics of nanosecond pulsed laser-induced aluminum plasmas

    Directory of Open Access Journals (Sweden)

    Mahmoud S. Dawood

    2015-10-01

    Full Text Available In this article, we present a comprehensive study of the plume dynamics of plasmas generated by laser ablation of an aluminum target. The effect of both ambient gas composition (helium, nitrogen or argon and pressure (from ∼5 × 10−7 Torr up to atmosphere is studied. The time- and space- resolved observation of the plasma plume are performed from spectrally integrated images using an intensified Charge Coupled Device (iCCD camera. The iCCD images show that the ambient gas does not significantly influence the plume as long as the gas pressure is lower than 20 Torr and the time delay below 300 ns. However, for pressures higher than 20 Torr, the effect of the ambient gas becomes important, the shortest plasma plume length being observed when the gas mass species is highest. On the other hand, space- and time- resolved emission spectroscopy of aluminum ions at λ = 281.6 nm are used to determine the Time-Of-Flight (TOF profiles. The effect of the ambient gas on the TOF profiles and therefore on the propagation velocity of Al ions is discussed. A correlation between the plasma plume expansion velocity deduced from the iCCD images and that estimated from the TOF profiles is presented. The observed differences are attributed mainly to the different physical mechanisms governing the two diagnostic techniques.

  8. Influence of center of pressure estimation errors on 3D inverse dynamics solutions during gait at different velocities.

    Science.gov (United States)

    Camargo-Junior, Franklin; Ackermann, Marko; Loss, Jefferson F; Sacco, Isabel C N

    2013-12-01

    The aim of this study was to investigate the effect of errors in the location of the center of pressure (5 and 10 mm) on lower limb joint moment uncertainties at different gait velocities (1.0, 1.5, and 2.0 m/s). Our hypotheses were that the absolute joint moment uncertainties would be gradually reduced from distal to proximal joints and from higher to lower velocities. Joint moments of five healthy young adults were calculated by inverse dynamics using the bottom-up approach, depending on which estimate the uncertainty propagated. Results indicated that there is a linear relationship between errors in center of pressure and joint moment uncertainties. The absolute moment peak uncertainties expressed on the anatomic reference frames decreased from distal to proximal joints, confirming our first hypothesis, except for the abduction moments. There was an increase in moment uncertainty (up to 0.04 N m/kg for the 10 mm error in the center of pressure) from the lower to higher gait velocity, confirming our second hypothesis, although, once again, not for hip or knee abduction. Finally, depending on the plane of movement and the joint, relative uncertainties experienced variation (between 5 and 31%), and the knee joint moments were the most affected.

  9. Kinetics and dynamics of nanosecond streamer discharge in atmospheric-pressure gas bubble suspended in distilled water under saturated vapor pressure conditions

    KAUST Repository

    Sharma, Ashish

    2016-09-08

    We perform computational studies of nanosecond streamer discharges generated in helium bubbles immersed in distilled water under atmospheric pressure conditions. The model takes into account the presence of water vapor in the gas bubble for an accurate description of the discharge kinetics. We find that the dynamic characteristics of the streamer discharge are different at low and high positive trigger voltages with the axial streamer evolution dominant for low voltages and a surface hugging mode favored for high voltages. We also find a substantial difference in initiation, transition and evolution stages of discharge for positive and negative trigger voltages with the volumetric distribution of species in the streamer channel much more uniform for negative trigger voltages on account of the presence of multiple streamers. We observe that the presence of water vapor does not affect the breakdown voltage even for oversaturated conditions but significantly influences the composition of dominant species in the trail of the streamer as well as the flux of the dominant species on the bubble surface. © 2016 IOP Publishing Ltd.

  10. Kinetics and dynamics of nanosecond streamer discharge in atmospheric-pressure gas bubble suspended in distilled water under saturated vapor pressure conditions

    Science.gov (United States)

    Sharma, Ashish; Levko, Dmitry; Raja, Laxminarayan L.; Cha, Min Suk

    2016-10-01

    We perform computational studies of nanosecond streamer discharges generated in helium bubbles immersed in distilled water under atmospheric pressure conditions. The model takes into account the presence of water vapor in the gas bubble for an accurate description of the discharge kinetics. We find that the dynamic characteristics of the streamer discharge are different at low and high positive trigger voltages with the axial streamer evolution dominant for low voltages and a surface hugging mode favored for high voltages. We also find a substantial difference in initiation, transition and evolution stages of discharge for positive and negative trigger voltages with the volumetric distribution of species in the streamer channel much more uniform for negative trigger voltages on account of the presence of multiple streamers. We observe that the presence of water vapor does not affect the breakdown voltage even for oversaturated conditions but significantly influences the composition of dominant species in the trail of the streamer as well as the flux of the dominant species on the bubble surface.

  11. A first principles study of phase stability, bonding, electronic and lattice dynamical properties of beryllium chalcogenides at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Dabhi, Shweta [Department of Physics, Maharaja Krishnakumarsinhji Bhavnagar University, Bhavnagar 364001 (India); Mankad, Venu [Central Institute of Plastic Engineering and Technology, Ahmedabad (India); Jha, Prafulla K., E-mail: prafullaj@yahoo.com [Department of Physics, Faculty of Science, The M.S. University of Baroda, Vadodara 390002 (India)

    2014-12-25

    Highlights: • First principles calculations are performed for BeS, BeSe and BeTe in B3, B8 and B1 phases. • They are indirect wide band gap semiconductors stable in B3 phase at ambient condition. • Phonon calculations at ambient and high pressure are reported. • The NiAs phase is dynamically stable at high pressure. - Abstract: The present paper reports a detailed and systematic theoretical study of structural, mechanical, electronic, vibrational and thermodynamical properties of three beryllium chalcogenides BeS, BeSe and BeTe in zinc blende, NiAs and rock salt phases by performing ab initio calculations based on density-functional theory. The calculated value of lattice constants and bulk modulus are compared with the available experimental and other theoretical data and found to agree reasonably well. These compounds are indirect wide band gap semiconductors with a partially ionic contribution in all considered three phases. The zinc blende phase of these chalcogenides is found stable at ambient condition and phase transition from zinc blende to NiAs structure is found to occur. The bulk modulus, its pressure derivative, anisotropic factor, Poission’s ratio, Young’s modulus for these are also calculated and discussed. The phonon dispersion curves of these beryllium chalcogenides in zinc blende phase depict their dynamical stability in this phase at ambient condition. We have also estimated the temperature variation of specific heat at constant volume, entropy and Debye temperature for these compounds in zinc blende phase. The variation of lattice-specific heat with temperature obeys the classical Dulong–Petit’s law at high temperature, while at low-temperature it obeys the Debye’s T{sup 3} law.

  12. IMF By effects on ground magnetometer response to increased solar wind dynamic pressure derived from global MHD simulations

    Science.gov (United States)

    Ozturk, Dogacan Su; Zou, Shasha; Slavin, James A.

    2017-05-01

    During sudden solar wind dynamic pressure enhancements, the magnetosphere undergoes rapid compression resulting in a reconfiguration of the global current systems, most notably the field-aligned currents (FACs). Ground-based magnetometers are traditionally used to study such compression events. However, factors affecting the polarity and magnitude of the ground-based magnetic perturbations are still not well understood. In particular, interplanetary magnetic field (IMF) By is known to create significant asymmetries in the FAC patterns. We use the University of Michigan Block Adaptive Tree Roe Upwind Scheme (BATS'R'US) magnetohydrodynamic code to investigate the effects of IMF By on the global variations of ground magnetic perturbations during solar wind dynamic pressure enhancements. Using virtual magnetometers in three idealized simulations with varying IMF By, we find asymmetries in the peak amplitude and magnetic local time of the ground magnetic perturbations during the preliminary impulse (PI) and the main impulse (MI) phases. These asymmetries are especially evident at high-latitude ground magnetometer responses where the peak amplitudes differ by 50 nT at different locations. We show that the FACs related with the PI are due to magnetopause deformation, and the FACs related with the MI are generated by vortical flows within the magnetosphere, consistent with other simulation results. The perturbation FACs due to pressure enhancements and their magnetospheric sources do not differ much under different IMF By polarities. However, the conductance profile affected by the superposition of the preexisting FACs and the perturbation FACs including their closure currents is responsible for the magnitude and location asymmetries in the ground magnetic perturbations.

  13. Modelling of the dynamic relationship between arterial pressure, renal sympathetic nerve activity and renal blood flow in conscious rabbits.

    Science.gov (United States)

    Berger, C S; Malpas, S C

    1998-12-01

    A linear autoregressive/moving-average model was developed to describe the dynamic relationship between mean arterial pressure (MAP), renal sympathetic nerve activity (SNA) and renal blood flow (RBF) in conscious rabbits. The RBF and SNA to the same kidney were measured under resting conditions in a group of eight rabbits. Spectral analysis of the data sampled at 0.4 Hz showed that the low-pass bandwidth of the signal power for RBF was approximately 0. 05 Hz. An autoregressive/moving-average model with an exogenous input (ARMAX) was then derived (using the iterative Gauss-Newton algorithm provided by the MATLAB identification Toolbox), with MAP and SNA as inputs and RBF as output, to model the low-frequency fluctuations. The model step responses of RBF to changes in SNA and arterial pressure indicated an overdamped response with a settling time that was usually less than 2 s. Calculated residuals from the model indicated that 79 5 % (mean s.d., averaged over eight independent experiments) of the variation in RBF could be accounted for by the variations in arterial pressure and SNA. Two additional single-input models for each of the inputs were similarly obtained and showed conclusively that changes in RBF, in the conscious resting rabbit, are a function of both SNA and MAP and that the SNA signal has the predominant effect. These results indicate a strong reliance on SNA for the dynamic regulation of RBF. Such information is likely to be important in understanding the diminished renal function that occurs in a variety of disease conditions in which overactivity of the sympathetic nervous system occurs.

  14. In-situ Observation of Boiling Dynamics on Fuel Cladding Surface in Non-pressurized Water Using Acoustic Emission Method

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Kaige; Baek, Seung Heon; Shim, Hee-Sang; Hur, Do Haeng; Lee, Deok Hyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    In the PWR primary coolant system, a phenomenon of axial offset anomaly (AOA) can be caused due to accumulated boron hide out in porous CRUD deposition on the fuel cladding surface. Up to now, the CRUD deposition has been well known to be driven by subcooled nucleate boiling (SNB) on the cladding surface based on large scale experimental work. Therefore, monitoring and evaluation of the SNB-phenomenon is an important approach to study the CRUD deposition. Many attempts have been made to study the SNB and CRUD deposition using thermal hydraulic or model calculation. However, a comprehensive understanding of the SNB during CRUD deposition is still far from being realized. Acoustic emission (AE) technique, as an in-situ nondestructive evaluation (NDE) method, has been widely used to monitor the boiling activity in containers and pipes. Accordingly, this work aimed to investigate the exact AE characteristics of SNB-phenomenon on the fuel cladding surface at atmospheric pressure, with the purpose of providing an experimental groundwork for the AE investigation on SNB in high-temperature pressurized coolant system. In this study, we conducted an in-situ experimental observation of the bubble dynamic of SNB in non-pressurized water at atmospheric pressure using AE method. The AE of heater noise was confirmed to cluster between 8 and 26 khz. Three AE groups were detected during the boiling process in the Snob zones. AE group 1 and 3 seemed to be the results of bubble growth and collapse, while bubble departure from the cladding surface was reasonably associated with an isolated AE group 2.

  15. Population dynamics of the brown alga Himanthalia elongata under harvesting pressure

    Science.gov (United States)

    Stagnol, Doriane; Michel, Renaud; Davoult, Dominique

    2016-06-01

    Through experimental harvesting, followed by a 12-month monitoring of demographic attributes, we tested the influence of harvesting on the population dynamics of Himanthalia elongata. We further explore the data to test the hypothesis that the canopy would exert a negative effect on the other developmental stages (intraspecific competition) throughout the recovery cycle of the population. This showed that the H. elongata canopy plays a marked seasonal role not by precluding the presence of other developmental stages but by delaying or preventing their growth and development. The removal of the canopy facilitates the transition from one developmental stage to another, eventually permitting a fast recovery of size structure in the population. This study allows us to integrate population dynamics and intraspecific relationships in our understanding of macroalgal recovery patterns.

  16. Dynamics of carbon sources supporting burial in seagrass sediments under increasing anthropogenic pressure

    KAUST Repository

    Mazarrasa, Inés

    2017-03-15

    Seagrass meadows are strong coastal carbon sinks of autochthonous and allochthonous carbon. The aim of this study was to assess the effect of coastal anthropogenic pressure on the variability of carbon sources in seagrass carbon sinks during the last 150 yr. We did so by examining the composition of the sediment organic carbon (Corg) stocks by measuring the δ13Corg signature and C : N ratio in 210Pb dated sediments of 11 Posidonia oceanica seagrass meadows around the Balearic Islands (Spain, Western Mediterranean) under different levels of human pressure. On average, the top meter sediment carbon deposits were mainly (59% ± 12%) composed by P. oceanica derived carbon whereas seston contribution was generally lower (41% ± 8%). The contribution of P. oceanica to the total sediment carbon stock was the highest (∼ 80%) in the most pristine sites whereas the sestonic contribution was the highest (∼ 40–80%) in the meadows located in areas under moderate to very high human pressure. Furthermore, an increase in the contribution of sestonic carbon and a decrease in that of seagrass derived carbon toward present was observed in most of the meadows examined, coincident with the onset of the tourism industry development and coastal urbanization in the region. Our results demonstrate a general increase of total carbon accumulation rate in P. oceanica sediments during the last century, mainly driven by the increase in sestonic Corg carbon burial, which may have important implications in the long-term carbon sink capacity of the seagrass meadows in the region examined.

  17. Population dynamics of the brown alga Himanthalia elongata under harvesting pressure

    OpenAIRE

    2016-01-01

    International audience; Through experimental harvesting, followed by a 12-month monitoring of demographic attributes, we tested the influence of harvesting on the population dynamics of Himanthalia elongata. We further explore the data to test the hypothesis that the canopy would exert a negative effect on the other developmental stages (intraspecific competition) throughout the recovery cycle of the population. This showed that the H. elongata canopy plays a marked seasonal role not by precl...

  18. Learning Effects on Strategy Selection in a Dynamic Task Environment as a Function of Time Pressure

    Science.gov (United States)

    1994-06-01

    MANAGEMENT UI1TREKSEL Previous research on strategy selection in dynamic task environments indicated that subjects preferred to request information first...I febwari 1994 is de naam Instituut voor Zintuigfysiologie TNO gewijzigd in TNO Technische Menskunde. 2 CONTENTS Page SUMMARY 3 SAMENVAITING 4 I...waarin men gebruik maakt van de continue feedback over de toestand van het systeem . Proefpersonen moesten het veranderende conditieniveau van een atleet

  19. Dynamical behavior of rapeseed oil and methyl ester of rapeseed oil during high-pressure injection

    Science.gov (United States)

    Bambuleac, Dumitru

    2012-04-01

    Fuels' physical properties such as density, viscosity, speed of sound and bulk modulus have and important influence on the engine performance. This work will study the behavior of the rapeseed oil and methyl ester of rapeseed oil during high-pressure injection. Several aspects of the injection and combustion process will be analyzed in order to try to find out in what manner these aspects are influenced by the above-mentioned fuels' characteristics and also by different operating regimes. In such a way, some features of the technical efficiency of the two non-conventional diesel fuels will be determined. As a reference, it will serve the results from testing classical diesel.

  20. Ice flow dynamics forced by rapid water pressure variations in subglacial granular beds

    DEFF Research Database (Denmark)

    Damsgaard, Anders; Egholm, David Lundbek; Beem, Lucas H.;

    2016-01-01

    mechanical processes driving transitions from stability to slip. We performed computational experiments that show how rearrangements of load-bearing force chains within the granular sediments drive the mechanical transitions. Cyclic variations in pore water pressure give rise to rate-dependent creeping......Glaciers and ice streams can move by deforming underlying water-saturated sediments, and the nonlinear mechanics of these materials are often invoked as the main reason for initiation, persistence, and shutdown of fast-flowing ice streams. Existing models have failed to fully explain the internal...

  1. Full-density, net-shape powder consolidation using dynamic magnetic pulse pressures

    Science.gov (United States)

    Chelluri, Bhanu; Barber, John P.

    1999-07-01

    The full-density consolidation of powders into net-shape parts yields high green strength, low shrinkage, short sinter times, superior mechanical properties, and low manufacturing costs. The conventional lowcost, single-press, single-sinter process typically densifies powders at less than 65 percent green density. This article describes the Magnepress™ process, a powder-processing technique wherein pulsed magnetic pressures consolidate powders into full-density parts without admixed lubricants or binders. The Magnepress technique is especially suitable for producing net-shape products with radial symmetry (e.g., rods, cylindrical parts with internal features, tubular shapes, and high aspect-ratio specimens).

  2. Dynamic earthquake sequence simulations with fault constitutive law accounting for brittle-plastic transition and pressure solution-precipitation creep

    Science.gov (United States)

    Noda, Hiroyuki; Shimamoto, Toshihiko

    2015-04-01

    Fault mechanical behavior is presumably dictated by a pressure-sensitive friction law in the brittle regime where cataclastic deformation dominates, and by a pressure-insensitive flow law in the plastic regime where milonytes are generated. A fault constitutive law in the transitional regime is of great importance in considering earthquake cycles as evidenced by field observations of repeating brittle and ductile deformations [e.g., Sibson 1980]. Shimamoto and Noda [2014] proposed an empirical method of connecting the friction law and the flow law without introducing a new parameter, and demonstrated 2-D dynamic earthquake sequence simulations for a strike-slip fault [e.g., Lapusta et al., 2000] with the friction-to-flow law. A logarithmic rate- and state-dependent friction law (aging law) and a rate- and state-dependent flow law (power law) [Noda and Shimamoto, 2010] with a quartzite steady-state flow law (power exponent n = 4) [Hirth et al., 2001] were adopted for the friction law and the flow law, respectively. Our numerical models are realization of conceptual fault models [e.g., Scholz, 1988]. "Christmas tree" stress profiles appear as a result of evolution of the system, and fluctuate with time. During the interseismic periods, creep fronts penetrated into the locked depth, slow slip events were generated, and then nucleation of dynamic rupture took place either in the shallower or deeper creeping region. The dynamic ruptures spanned the locked depth, reaching the ground surface and extending downwards even deeper than the depth of maximum pre-stress where the deformation mode was in the transitional regime preseismically where S-C mylonitic texture was expected [Shimamoto, 1989]. The coseismic deformation was in the frictional regime because the pure flow law predicts tremendously high flow stress at high strain rate and "the weaker wins". Our simulations reproduced repeating overprint of brittle and ductile deformations. We attempt here to include pressure

  3. 射流撞击过程中的高频压力脉动特性%CHARACTERISTICS OF DYNAMIC PRESSURE IN IMPINGING JET

    Institute of Scientific and Technical Information of China (English)

    王亭杰; 肖帅刚; 崔爱莉; 林玉兰; 金涌

    2001-01-01

    The characteristics of dynamic pressure in an impinging jet wereexperimentally studied. The instantaneous signals of dynamic pressure resulted from the turbulence in the jetting fluid were measured through a piezoelectric sensor and recorded by a computer. The pressure signals at central axial position of the jetting fluid were sampled at different fluid pressure. The measured signals obviously possessed periodical characteristics. After analyzing the signals with FFT method,it was found that there was an inherent frequency in the dynamic pressure signals. The inherent frequency increases with the average velocity of the jetting fluid at the nozzle outlet,which is consistent with the theoretical analysis. It was supposed that the dynamic pressure signals are transformed from the fluctuating fluid velocities resulted from the turbulence in the jetting fluid. The inherent frequency corresponds to the minimum eddy scale in the turbulent jet. The smaller the eddy scale is,the higher the inherent frequency is. Higher velocity of the fluid at the outlet leads to a stronger turbulent strength. The fluctuation velocities with high inherent frequency resulted in a strong shear force field,which enables the fluid to be micro-mixed fleetly and the agglomerate of solid particles to be dispersed effectively.

  4. Intraocular pressure dynamics with prostaglandin analogs: a clinical application of water-drinking test

    Directory of Open Access Journals (Sweden)

    Özyol P

    2016-07-01

    Full Text Available Pelin Özyol,1 Erhan Özyol,1 Ercan Baldemir2 1Ophthalmology Department, 2Biostatistics Department, Faculty of Medicine, Mugla Sitki Kocman University, Mugla, Turkey Aim: To evaluate the clinical applicability of the water-drinking test in treatment-naive primary open-angle glaucoma patients. Methods: Twenty newly diagnosed primary open-angle glaucoma patients and 20 healthy controls were enrolled in this prospective study. The water-drinking test was performed at baseline and 6 weeks and 3 months after prostaglandin analog treatment. Peak and fluctuation of intraocular pressure (IOP measurements obtained with the water-drinking test during follow-up were analyzed. Analysis of variance for repeated measures and paired and unpaired t-tests were used for statistical analysis. Results: The mean baseline IOP values in patients with primary open-angle glaucoma were 25.1±4.6 mmHg before prostaglandin analog treatment, 19.8±3.7 mmHg at week 6, and 17.9±2.2 mmHg at month 3 after treatment. The difference in mean baseline IOP of the water-drinking tests was statistically significant (P<0.001. At 6 weeks of prostaglandin analog treatment, two patients had high peak and fluctuation of IOP measurements despite a reduction in baseline IOP. After modifying treatment, patients had lower peak and fluctuation of IOP values at month 3 of the study. Conclusion: Peak and fluctuation of IOP in response to the water-drinking test were lower with prostaglandin analogs compared with before medication. The water-drinking test can represent an additional benefit in the management of glaucoma patients, especially by detecting higher peak and fluctuation of IOP values despite a reduced mean IOP. Therefore, it could be helpful as a supplementary method in monitoring IOP in the clinical practice. Keywords: glaucoma, intraocular pressure, water-drinking test, prostaglandin analog, intra­ocular pressure fluctuation

  5. Estimation of dynamic properties of attractors observed in hollow copper electrode atmospheric pressure arc plasma system

    Indian Academy of Sciences (India)

    S Ghorul; S N Sahasrabudhe; P S S Murthy; A K Das; N Venkatramani

    2002-07-01

    Understanding of the basic nature of arc root fluctuation is still one of the unsolved problems in thermal arc plasma physics. It has direct impact on myriads of thermal plasma applications being implemented at present. Recently, chaotic nature of arc root behavior has been reported through the analysis of voltages, acoustic and optical signals which are generated from a hollow copper electrode arc plasma torch. In this paper we present details of computations involved in the estimation process of various dynamic properties and show how they reflect chaotic behavior of arc root in the system.

  6. The effect of orthostasis on recurrence quantification analysis of heart rate and blood pressure dynamics.

    Science.gov (United States)

    Javorka, M; Turianikova, Z; Tonhajzerova, I; Javorka, K; Baumert, M

    2009-01-01

    The purpose of this paper is to investigate the effect of orthostatic challenge on recurrence plot based complexity measures of heart rate and blood pressure variability (HRV and BPV). HRV and BPV complexities were assessed in 28 healthy subjects over 15 min in the supine and standing positions. The complexity of HRV and BPV was assessed based on recurrence quantification analysis. HRV complexity was reduced along with the HRV magnitude after changing from the supine to the standing position. In contrast, the BPV magnitude increased and BPV complexity decreased upon standing. Recurrence quantification analysis (RQA) of HRV and BPV is sensitive to orthostatic challenge and might therefore be suited to assess changes in autonomic neural outflow to the cardiovascular system.

  7. Dynamics of a condensing liquid film under conjoining/disjoining pressures

    Science.gov (United States)

    Oron, Alexander; Bankoff, S. George

    2001-05-01

    The dynamics of a condensing apolar ultrathin liquid film is studied in the framework of long-wave theory in the cases of both horizontal and slightly tilted solid coated surfaces. When condensation is slow, the film on a horizontal substrate passes through the stages of hole opening driven by the "reverse reservoir effect," hole closing, eventual thickness equilibration and further spatially uniform growth of the condensate. When condensation is faster and the resistance to phase change is lower, secondary droplet(s) may emerge within the hole. During the film evolution the thickness of the microlayer covering the hole remains practically constant due to the "reverse reservoir effect." The total heat flux across the condensate film is found to decrease with the absolute value of the condensation constant. When the solid substrate is tilted, the film dynamics exhibits the formation of multidrop structures and their coarsening along with the stages typical for the horizontal case. The increase of the tilt angle leads to faster transition from dropwise to filmwise condensation and to the increase of the total heat flux through the condensate.

  8. NEUTRON SCATTERING AND LATTICE DYNAMICAL STUDIES OF THE HIGH-PRESSURE PHASE ICE (II)

    Institute of Scientific and Technical Information of China (English)

    董顺乐; 王燕

    2001-01-01

    Lattice dynamical calculations have been carried out for ice II based on the force field constructed for ice Ih. In order to fully understand ice II inelastic neutron scattering spectra, the decomposed phonon density of states was shown mode by mode. Calculated results have shown that the hydrogen bond force constant between the six-molecule rings is significantly weaker, 75eV/nm2, compared with the force constant, 220eV/nm2, within the rings. Inelastic neutron scattering spectra of clathrate hydrate H2O+He are almost the same as ice II. This means that the absorption of He atoms cannot affect the bond strengths of the ice II host lattice. Based on the force field model for ice II, the van der Waals interactions between water molecules and helium atoms are considered. The results obtained are consistent with experimental data. Lattice dynamical calculations have been carried out for ice II using seven rigid pairwise potentials.It was found that MCY makes the stretching and bending interactions in ice II too weak and makes the O-O bond length too long (~5%), thus its lattice densities are obviously lower than other potential lattices or experimental values.

  9. Computerized simulation of the dynamic response of a coal-fired power plant with pressurized fluidized bed

    Science.gov (United States)

    Plackmeyer, J.

    1982-07-01

    The simple way of desulfurizing, the efficient combustion of coal, and low carbon monoxide flue gas content of a fluidized bed combustion installation were studied. The dynamic response of a pressurized fluidized bed should also be studied before any construction is started. The physical-mathematical models of all single components were developed and combined in a total computer program. Starting point was the planned pilot plant with gas turbine engine. Various modifications of the purely air cooled plant as well as the extension to a combined cycle with additional steam turbine were considered. Operating cases were simulated: starting up, increasing from partial load to full load and vice versa, shut down and breakdowns. Results show that all operating cases could be brought under control as well as breakdowns. The constructive precautions and correct plant practice are described.

  10. Transport and concentration processes in the multidimensional zero-pressure gas dynamics model with the energy conservation law

    CERN Document Server

    Albeverio, S; Shelkovich, V M

    2011-01-01

    We introduce integral identities to define delta-shock wave type solutions for the multidimensional zero-pressure gas dynamics Using these integral identities, the Rankine-Hugoniot conditions for delta-shocks are obtained. We derive the balance laws describing mass, momentum, and energy transport from the area outside the delta-shock wave front onto this front. These processes are going on in such a way that the total mass, momentum, and energy are conserved and at the same time mass and energy of the moving delta-shock wave front are increasing quantities. In addition, the total kinetic energy transfers into the total internal energy. The process of propagation of delta-shock waves is also described. These results can be used in modeling of mediums which can be treated as a {pressureless continuum} (dusty gases, two-phase flows with solid particles or droplets, granular gases).

  11. A low-power tool for measuring acceleration, pressure, and temperature (APT) with wide dynamic range and bandwidth

    Science.gov (United States)

    Heesemann, Martin; Davis, Earl E.; Paros, Jerome; Johnson, Greg; Meldrum, Robert; Scherwath, Martin; Mihaly, Steven

    2017-04-01

    We present a new tool that facilitates the study of inter-related geodetic, geodynamic, seismic, and oceanographic phenomena. It incorporates a temperature compensated tri-axial accelerometer developed by Quartz Seismic Sensors, Inc., a pressure sensor built by Paroscientific Inc., and a low-power, high-precision frequency counter developed by Bennest Enterprises Ltd. and built by RBR, Ltd. The sensors are housed in a 7 cm o.d. titanium pressure case designed for use to full ocean depths (withstands more than 20 km of water pressure). Sampling intervals are programmable from 0.08 s to 1 hr; standard memory can store up to 130 million samples; total power consumption is roughly 115 mW when operating continuously and proportionately lower when operating intermittently (e.g., 2 mW average at 1 sample per min). Serial and USB communications protocols allow a variety of autonomous and cable-connection options. Measurement precision of the order of 10-8 of full scale (e.g., pressure equivalent to 4000 m water depth, acceleration = +/- 3 g) allows observations of pressure and acceleration variations of 0.4 Pa and 0.3 μm s-2. Long-term variations in vertical acceleration are sensitive to displacement through the gravity gradient down to a level of roughly 2 cm, and variations in horizontal acceleration are sensitive to tilt down to a level of 0.03 μrad. With the large dynamic ranges, high sensitivities and broad bandwidth (6 Hz to DC), ground motion associated with microseisms, strong and weak seismic ground motion, tidal loading, and slow and rapid geodynamic deformation - all normally studied using disparate instruments - can be observed with a single tool. Installation in the marine environment is accomplished by pushing the tool roughly 1 m vertically below the seafloor with a submersible or remotely operated vehicle, with no profile remaining above the seafloor to cause current-induced noise. The weight of the tool is designed to match the sediment it displaces to

  12. Dynamic response of a transducer mounted at one end of an acoustical cavity which is subjected to a specified pressure at the open end of the cavity

    Energy Technology Data Exchange (ETDEWEB)

    Benedetti, G.A.; Benson, J.Z.

    1994-11-01

    The purpose of this report is to develop a mathematical model for a pressure transducer mounted in a fluid filled cavity (a system) and examine the pressure ``measurement`` error of the cavity and transducer by computing the dynamic response (output pressure) of the system to a specified pressure time history (input pressure). The ``measurement`` error is determined by comparing the calculated output pressure to the specified input pressure. The dynamic response of a transducer mounted at one end of a one-dimensional acoustical cavity is determined. The cavity is filled with a compressible isentropic fluid, and the fluid at the open end of the cavity (i.e., the boundary at x = 0) is subjected to a specified uniform axial input pressure. At the other end of the cavity the transducer is represented as a mass, spring, and damper system. Consequently, the boundary condition at x = {ell} is also time dependent. The general solution to the boundary value problem, as well as the steady state solution for periodic excitation, is obtained by integrating a coupled set of ordinary differential equations.

  13. Implications for anomalous mantle pressure and dynamic topography from lithospheric stress patterns in the North Atlantic Realm

    Science.gov (United States)

    Schiffer, Christian; Nielsen, Søren Bom

    2016-08-01

    With convergent plate boundaries at some distance, the sources of the lithospheric stress field of the North Atlantic Realm are mainly mantle tractions at the base of the lithosphere, lithospheric density structure and topography. Given this, we estimate horizontal deviatoric stresses using a well-established thin sheet model in a global finite element representation. We adjust the lithospheric thickness and the sub-lithospheric pressure iteratively, comparing modelled in plane stress with the observations of the World Stress Map. We find that an anomalous mantle pressure associated with the Iceland and Azores melt anomalies, as well as topography are able to explain the general pattern of the principle horizontal stress directions. The Iceland melt anomaly overprints the classic ridge push perpendicular to the Mid Atlantic ridge and affects the conjugate passive margins in East Greenland more than in western Scandinavia. The dynamic support of topography shows a distinct maximum of c. 1000 m in Iceland and amounts Greenland. Considering that large areas of the North Atlantic Realm have been estimated to be sub-aerial during the time of break-up, two components of dynamic topography seem to have affected the area: a short-lived, which affected a wider area along the rift system and quickly dissipated after break-up, and a more durable in the close vicinity of Iceland. This is consistent with the appearance of a buoyancy anomaly at the base of the North Atlantic lithosphere at or slightly before continental breakup, relatively fast dissipation of the fringes of this, and continued melt generation below Iceland.

  14. Investigation of different modeling approaches for computational fluid dynamics simulation of high-pressure rocket combustors

    Science.gov (United States)

    Ivancic, B.; Riedmann, H.; Frey, M.; Knab, O.; Karl, S.; Hannemann, K.

    2016-07-01

    The paper summarizes technical results and first highlights of the cooperation between DLR and Airbus Defence and Space (DS) within the work package "CFD Modeling of Combustion Chamber Processes" conducted in the frame of the Propulsion 2020 Project. Within the addressed work package, DLR Göttingen and Airbus DS Ottobrunn have identified several test cases where adequate test data are available and which can be used for proper validation of the computational fluid dynamics (CFD) tools. In this paper, the first test case, the Penn State chamber (RCM1), is discussed. Presenting the simulation results from three different tools, it is shown that the test case can be computed properly with steady-state Reynolds-averaged Navier-Stokes (RANS) approaches. The achieved simulation results reproduce the measured wall heat flux as an important validation parameter very well but also reveal some inconsistencies in the test data which are addressed in this paper.

  15. Foaming morphology control of microcellular injection molded parts with gas counter pressure and dynamic mold temperature control

    Science.gov (United States)

    Shiu, Tai-Yi; Huang, Chao-Tsai; Chang, Rong-Yu; Hwang, Shyh-Shin

    2014-05-01

    Microcellular injection molding process is a promising solution for products with special requirements such as weight reduction, extra thin wall, high dimensional stability, clamping force reduction, etc. Despite microcellular foaming application used in reciprocating screw injection molding machine was built more than a decade, some limitations, such as poor surface quality or poor foaming control, confine the usage of this technology. Earlier CAE simulation tool for microcellular injection molding was not successful due to insufficient physical and computational considerations, limited by complicated bubble growth mechanism; so that, an economic and efficient tool for examining foaming quality of injection foaming product was lack. In this study, a recent developed three-dimensional simulation tool is used to predict injection foaming process. Predictions are carried out with commodity polypropylene and polystyrene with nitrogen and carbon dioxide supercritical fluids (SCFs). Comparisons of simulations between microcellular injection molding with and without counter pressure are discussed to provide insights into the correlation of surface quality and cell size distribution near the surface of product. Furthermore, comparisons between simulation predictions and experimental results of molding process, which is featured with dynamic mold temperature and gas counter pressure, are given for understanding quality improvement by controlling foaming morphology, and benefit of industrial application.

  16. Features of the non-contact carotid pressure waveform: Cardiac and vascular dynamics during rebreathing

    Science.gov (United States)

    Casaccia, S.; Sirevaag, E. J.; Richter, E. J.; O'Sullivan, J. A.; Scalise, L.; Rohrbaugh, J. W.

    2016-10-01

    This report amplifies and extends prior descriptions of the use of laser Doppler vibrometry (LDV) as a method for assessing cardiovascular activity, on a non-contact basis. A rebreathing task (n = 35 healthy individuals) was used to elicit multiple effects associated with changes in autonomic drive as well as blood gases including hypercapnia. The LDV pulse was obtained from two sites overlying the carotid artery, separated by 40 mm. A robust pulse signal was obtained from both sites, in accord with the well-described changes in carotid diameter over the blood pressure cycle. Emphasis was placed on extracting timing measures from the LDV pulse, which could serve as surrogate measures of pulse wave velocity (PWV) and the associated arterial stiffness. For validation purposes, a standard measure of pulse transit time (PTT) to the radial artery was obtained using a tonometric sensor. Two key measures of timing were extracted from the LDV pulse. One involved the transit time along the 40 mm distance separating the two LDV measurement sites. A second measure involved the timing of a late feature of the LDV pulse contour, which was interpreted as reflection wave latency and thus a measure of round-trip travel time. Both LDV measures agreed with the conventional PTT measure, in disclosing increased PWV during periods of active rebreathing. These results thus provide additional evidence that measures based on the non-contact LDV technique might provide surrogate measures for those obtained using conventional, more obtrusive assessment methods that require attached sensors.

  17. A Comparative Analysis Between Optimized and Baseline High Pressure Compressor Stages Using Tridimensional Computational Fluid Dynamics

    Directory of Open Access Journals (Sweden)

    V. Dragan

    2016-08-01

    Full Text Available Re-vamping of industrial turbo-machinery is commonplace in the oil and gas industry in applications where subterranean combustion is used for oil extraction. The current case study refers to such an industrial compressor re-vamping, using a state of the art 3D fully viscous CFD methodology coupled with artificial neural networks (ANNs and genetic algorithms (GA. The ANN is used to establish correlations within a database of CFD simulations of geometrical variations of the original rotor and the GA uses those correlations to estimate an optimum. The estimate is then tested with the same CFD method and the results are fed back into the database, increasing the accuracy of the ANN correlations. The process is reiterated until the optimum estimated by the GA is confirmed with the CFD simulations. The resulting geometry is superior to the original in terms of efficiency and pressure ratio as well as the range of stabile operation, as confirmed by the successful implementation in the field. In this paper we present an analysis of why the optimized geometry achieves superior performances to the original one. Further work will present comparison between the detailed experimental data and CFD.

  18. LIDT-DD: A new self-consistent debris disc model including radiation pressure and coupling collisional and dynamical evolution

    CERN Document Server

    Kral, Quentin; Charnoz, Sébastien

    2013-01-01

    In most current debris disc models, the dynamical and the collisional evolutions are studied separately, with N-body and statistical codes, respectively, because of stringent computational constraints. We present here LIDT-DD, the first code able to mix both approaches in a fully self-consistent way. Our aim is for it to be generic enough so as to be applied to any astrophysical cases where we expect dynamics and collisions to be deeply interlocked with one another: planets in discs, violent massive breakups, destabilized planetesimal belts, exozodiacal discs, etc. The code takes its basic architecture from the LIDT3D algorithm developed by Charnoz et al.(2012) for protoplanetary discs, but has been strongly modified and updated in order to handle the very constraining specificities of debris discs physics: high-velocity fragmenting collisions, radiation-pressure affected orbits, absence of gas, etc. In LIDT-DD, grains of a given size at a given location in a disc are grouped into "super-particles", whose orb...

  19. A dynamic response model for pressure sensors in continuum and high Knudsen number flows with large temperature gradients

    Science.gov (United States)

    Whitmore, Stephen A.; Petersen, Brian J.; Scott, David D.

    1996-01-01

    This paper develops a dynamic model for pressure sensors in continuum and rarefied flows with longitudinal temperature gradients. The model was developed from the unsteady Navier-Stokes momentum, energy, and continuity equations and was linearized using small perturbations. The energy equation was decoupled from momentum and continuity assuming a polytropic flow process. Rarefied flow conditions were accounted for using a slip flow boundary condition at the tubing wall. The equations were radially averaged and solved assuming gas properties remain constant along a small tubing element. This fundamental solution was used as a building block for arbitrary geometries where fluid properties may also vary longitudinally in the tube. The problem was solved recursively starting at the transducer and working upstream in the tube. Dynamic frequency response tests were performed for continuum flow conditions in the presence of temperature gradients. These tests validated the recursive formulation of the model. Model steady-state behavior was analyzed using the final value theorem. Tests were performed for rarefied flow conditions and compared to the model steady-state response to evaluate the regime of applicability. Model comparisons were excellent for Knudsen numbers up to 0.6. Beyond this point, molecular affects caused model analyses to become inaccurate.

  20. Cerebral hemodynamics in normal-pressure hydrocephalus. Evaluation by 133Xe inhalation method and dynamic CT study

    Energy Technology Data Exchange (ETDEWEB)

    Tamaki, N.; Kusunoki, T.; Wakabayashi, T.; Matsumoto, S.

    1984-09-01

    Cerebral hemodynamics in 31 patients with suspected normal-pressure hydrocephalus were studied by means of the xenon-133 (133Xe) inhalation method and on dynamic computerized tomography (CT) scanning. Cerebral blood flow (CBF) is reduced in all patients with dementia. Hypoperfusion was noted in a frontal distribution in these patients compared with normal individuals. There was no difference in CBF patterns between patients with good and those with poor outcome. The CBF was increased following cerebrospinal fluid (CSF) shunting in patients who responded to that procedure: increase in flow correlated with clinical improvement, frontal and temporal lobe CBF was most markedly increased, and the CBF pattern became normal. In contrast, CBF was decreased after shunt placement in patients who were considered to have suffered from degenerative dementia, as evidenced by non-response to shunting. Dynamic computerized tomography studies demonstrated that patients with a good outcome showed a postoperative reduction in mean transit time of contrast material, most prominent in the frontal and temporal gray matter, and slight in the deep frontal structures, but not in the major cerebral vessels. Patients with poor outcome after shunting, however, had an increase in transit time in all regions. This corresponded well with the results as determined by the 133Xe inhalation method.

  1. Effects of continuous positive airway pressure on upper airway inspiratory dynamics in awake patients with sleep-disordered breathing.

    Science.gov (United States)

    Vérin, E; Similowski, T; Sériès, F

    2003-01-01

    Continuous positive airway pressure (CPAP) is the main treatment of the obstructive sleep apnoea syndrome (OSAS). We assessed its effects on the upper airway (UA) dynamics in response to bilateral anterior magnetic phrenic nerve stimulation (BAMPS) in 17 awake untreated OSAS patients (15 males; 52 +/- 7 years) whose effective CPAP (P(eff)) had been determined beforehand by a conventional titration sleep study. All twitch-related inspirations were flow-limited, flow first rising to a maximum (V(Imax)), then decreasing to a minimum (V(Imin)), and then increasing again (M-shaped pattern). Up to V(Imin), the relationship between driving pressure (P(d)) and flow (V) could adequately be fitted to a polynomial regression model (V = k(1)P(d) + k(2)P(d)(2); r(2) = 0.71-0.98, P < 0.0001). At atmospheric pressure V(Imax) was 700 +/- 377 ml s(-1), V(Imin) was 458 +/- 306 ml s(-1), k(1) was 154.5 +/- 63.9 ml s(-1) (cmH(2)O)(-1), and k(2) was 10.7 +/- 7.3 ml s(-1) (cmH(2)O)(-1). CPAP significantly increased V(Imax) and V(Imin) (peak values 1007 +/- 332 ml and 837 +/- 264 ml s(-1), respectively) as well as k(1) and k(2) (peak values 300.9 +/- 178.2 ml s(-1) (cmH(2)O)(-1) and 55.2 +/- 65.3 ml s(-1) (cmH(2)O)(-1), respectively). With increasing CPAP, k(1)/k(2) increased up to a peak value before decreasing. We defined as P(eff,stim) the CPAP value corresponding to the highest k(1)/k(2) value. P(eff,stim) was correlated with P(eff) (P(eff) = 7.0 +/- 2.0; P(eff,stim) = 6.4 +/- 2.6 cmH(2)O; r = 0.886; 95 % CI 0.696-0.960, P < 0.001). We conclude that CPAP improves UA dynamics in OSAS and that the therapeutic CPAP to apply can be predicted during wakefulness using BAMPS.

  2. Real-time feedback of dynamic foot pressure index for gait training of toe-walking children with spastic diplegia.

    Science.gov (United States)

    Pu, Fang; Ren, Weiyan; Fan, Xiaoya; Chen, Wei; Li, Shuyu; Li, Deyu; Wang, Yu; Fan, Yubo

    2017-09-01

    The aim of this study was to determine whether and how real-time feedback of dynamic foot pressure index (DFPI) could be used to correct toe-walking gait in spastic diplegic children with dynamic equinus. Thirteen spastic diplegic children with dynamic equinus were asked to wear a monitoring device to record their ambulation during daily gait, conventional training gait, and feedback training gait. Parameters based on their DFPI and stride duration were compared among the three test conditions. The results with feedback training were significantly better for all DFPI parameters in comparison to patients' daily gait and showed significant improvements in DFPI for toe-walking gait and percentage of normal gait in comparison to conventional training methods. Moreover, stride duration under two training gaits was longer than patient's daily gait, but there was no significant difference between the two training gaits. Although the stride duration for the two training gaits was similar, gait training with real-time feedback of DFPI did produce noticeably superior results by increasing heel-loading impulse of toe-walking gait and percentage of normal gait in comparison to convention training methods. However, its effectiveness was still impacted by the motion limitations of diplegic children. Implications for Rehabilitation The DFPI-based gait training feedback system introduced in this study was shown to be more effective at toe-walking gait rehabilitation training over conventional training methods. The feedback system accomplished superior improvement in correcting toe-walking gait, but its effectiveness in an increasing heel-loading impulse in normal gait was still limited by the motion limitations of diplegic children. Stride duration of normal gait and toe-walking gait was similar under conventional and feedback gait training.

  3. Effects of nitrate supplementation via beetroot juice on contracting rat skeletal muscle microvascular oxygen pressure dynamics

    Science.gov (United States)

    Ferguson, Scott K.; Hirai, Daniel M.; Copp, Steven W.; Holdsworth, Clark T.; Allen, Jason D.; Jones, Andrew M.; Musch, Timothy I.; Poole, David C.

    2013-01-01

    NO3− supplementation via beetroot juice (BR) augments exercising skeletal muscle blood flow subsequent to its reduction to NO2− then NO. We tested the hypothesis that enhanced vascular control following BR would elevate the skeletal muscle O2 delivery/O2 utilization ratio (microvascular PO2, PmvO2) and raise the PmvO2 during the rest-contractions transition. Rats were administered BR (~0.8 mmol/kg/day, n=10) or water (control, n=10) for 5 days. PmvO2 was measured during 180 s of electrically-induced (1 Hz) twitch spinotrapezius muscle contractions. There were no changes in resting or contracting steady-state PmvO2. However, BR slowed the PmvO2 fall following contractions onset such that time to reach 63% of the initial PmvO2 fall increased (MRT1; control: 16.8±1.9, BR: 24.4±2.7 s, p<0.05) and there was a slower relative rate of PmvO2 fall (Δ1PmvO2/τ1; control: 1.9±0.3, BR: 1.2±0.2 mmHg/s, p<0.05). Despite no significant changes in contracting steady state PmvO2, BR supplementation elevated the O2 driving pressure during the crucial rest-contractions transients thereby providing a potential mechanism by which BR supplementation may improve metabolic control. PMID:23584049

  4. Molecular Dynamics Simulation for the Binary Mixtures of High Pressure Carbon Dioxide and Ionic Liquids

    Institute of Scientific and Technical Information of China (English)

    徐君臣; 王松; 喻文; 徐琴琴; 王伟彬; 银建中

    2014-01-01

    Molecular dynamics simulation with an all-atom force field has been carried out on the two binary sys-tems of [bmim][PF6]-CO2 and [bmim][NO3]-CO2 to study the transport properties, volume expansion and micro-structures. It was found that addition of CO2 in the liquid phase can greatly decrease the viscosity of ionic liquids (ILs) and increase their diffusion coefficient obviously. Furthermore, the volume expansion of ionic liquids was found to increase with the increase of the mole fraction of CO2 in the liquid phase but less than 35%for the two simulated systems, which had a significant difference with CO2 expanded organic solvents. The main reason was that there were some void spaces inter and intra the molecules of ionic liquids. Finally, site to site radial distribution functions and corresponding number integrals were investigated and it was found that the change of microstructures of ILs by addition CO2 had a great influence on the properties of ILs.

  5. Population dynamics of American horseshoe crabs-historic climatic events and recent anthropogenic pressures

    Science.gov (United States)

    Faurby, S.; King, T.L.; Obst, M.; Hallerman, E.M.; Pertoldi, C.; Funch, P.

    2010-01-01

    Populations of the American horseshoe crab, Limulus polyphemus, have declined, but neither the causes nor the magnitude are fully understood. In order to evaluate historic demography, variation at 12 microsatellite DNA loci surveyed in 1218 L. polyphemus sampled from 28 localities was analysed with Bayesian coalescent-based methods. The analysis showed strong declines in population sizes throughout the species' distribution except in the geographically isolated southern-most population in Mexico, where a strong increase in population size was inferred. Analyses suggested that demographic changes in the core of the distribution occurred in association with the recolonization after the Ice Age and also by anthropogenic effects, such as the past overharvest of the species for fertilizer or the current use of the animals as bait for American eel (Anguilla rostrata) and whelk (Busycon spp.) fisheries. This study highlights the importance of considering both climatic changes and anthropogenic effects in efforts to understand population dynamics-a topic which is highly relevant in the ongoing assessments of the effects of climate change and overharvest. ?? 2010 Blackwell Publishing Ltd.

  6. Turbulent vortex-flow and dynamic pressure oscillations in regenerative blowers; Turbulente Wirbelstroemung und dynamische Druckschwankungen in Seitenkanalmaschinen

    Energy Technology Data Exchange (ETDEWEB)

    Surek, D. [Fachbereich Maschinenbau, Fachhochschule Merseburg (Germany)

    1997-05-01

    Regenerative blowers with high pressure coefficients have high dissipation losses in the side channel and on the breaker. These losses can be in the same magnitude as the polytropic specific head. The cause of the high specific dissipation energy is the turbulent vortex flow in the side channel, which is released by the high numbers of blades and restrict the polytropic efficiency by {eta}=0.46 to 0.50. The enforced turbulent vortex-flow is the reason for the high head coefficients of regenerative blowers. In the side channel, pressure pulsations occur with pressure amplitudes of high frequency up to 40 kHz. These dynamic pressure oscillations are the result of the turbulent vortex-flow. They are indicated from the edge of the impeller blades and the impeller flow in the side channel. For instance, for one rotation of the impeller t=0.02 s and the time between two blades t=0.35 ms. The analysis of the dynamic pressure shows a distribution of the amplitudes over a wide area up to 10 kHz and higher. The dominant amplitudes are the amplitude of blade rotation frequency. The forced turbulent vortex-flow causes a high turbulent vortex-viscosity in the flow and releases a pulse-flow transportation in the side channel. This is the reason for the energy transfer and the increase of the specific dissipation energy in the side channel. With knowledge of the specific pulse-flow transportation of the turbulent vortex-flow the connection to the total transmitted enthalpy can be explained. (orig.) [Deutsch] In Seitenkanalmaschinen mit den grossen Druckzahlen treten hohe Dissipationsverluste im Seitenkanal und im Unterbrecher auf, die von der gleichen Groessenordnung sein koennen wie die polytrope spezifische Nutzarbeit. Die Ursache fuer den grossen spezifischen Dissipationsenergieanteil ist in der turbulenten Wirbelstroemung im Seitenkanal zu suchen, die von den Laufradschaufeln hoher Zahl ausgeloest wird und den Wirkungsgrad der Maschinen auf Werte von {eta}=0,46... 0

  7. On the transition between two-phase and single-phase interface dynamics in multicomponent fluids at supercritical pressures

    Science.gov (United States)

    Dahms, Rainer N.; Oefelein, Joseph C.

    2013-09-01

    liquid injection is developed that quantifies the conditions under which classical sprays transition to dense-fluid jets. It is shown that the chamber pressure required to support diffusion-dominated mixing dynamics depends on the composition and temperature of the injected liquid and ambient gas. To illustrate the method and analysis, we use conditions typical of diesel engine injection. We also present a companion set of high-speed images to provide experimental validation of the presented theory. The basic theory is quite general and applies to a wide range of modern propulsion and power systems such as liquid rockets, gas turbines, and reciprocating engines. Interestingly, the regime diagram associated with diesel engine injection suggests that classical spray phenomena at typical injection conditions do not occur.

  8. The effects of backpack loads and spinal stabilization exercises on the dynamic foot pressure of elementary school children with idiopathic scoliosis.

    Science.gov (United States)

    Lee, Suemin; Shim, Jemyung

    2015-07-01

    [Purpose] The purpose of this study was to measure and observe the changes in dynamic plantar pressures when school children carried specific bag loads, and to determine whether improved physical balance after an eight-week spinal stabilization exercise program can influences plantar pressures. [Subjects] The subjects were 10 school students with Cobb angles of 10° or greater. [Methods] Gait View Pro 1.0 (Alfoots, Korea) was were based on to measure the pressure of the participants' feet. Spinal stabilization exercises used TOGU Multi-roll Functional (TOGU, Germany) training. Dynamic plantar pressures were measured with bag loads of 0% no bag and 15% of subjects' body weight. The independent t test was performed to analyze changes in plantar pressures. [Results] The plantar pressure measurements of bag load of 0% of subjects' body weight before and after the spinal stabilization exercise program were not significantly different, but those of two foot areas with a 15% load were statistically significant (mt5, 67.32±24.25 and 51.77±25.52 kPa; lat heel, 126.00±20.46 and 102.08±23.87 kPa). [Conclusion] After performance of the spinal stabilization exercises subjects' overall plantar pressures were reduced, which may suggest that physical balance improved.

  9. Pressure-induced emergence of unusually high-frequency transverse excitations in a liquid alkali metal: Evidence of two types of collective excitations contributing to the transverse dynamics at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Bryk, Taras [Institute for Condensed Matter Physics of the National Academy of Sciences of Ukraine, 1 Svientsitskii Street, UA-79011 Lviv (Ukraine); Lviv Polytechnic National University, 12 S. Bandera Street, UA-79013 Lviv (Ukraine); Ruocco, G. [Dipartimento di Fisica, Universita di Roma La Sapienza, 5 Piazzale Aldo Moro, I-00185 Roma (Italy); Center for Life Nano Science @Sapienza, Istituto Italiano di Tecnologia, 295 Viale Regina Elena, I-00161 Roma (Italy); Scopigno, T. [Dipartimento di Fisica, Universita di Roma La Sapienza, 5 Piazzale Aldo Moro, I-00185 Roma (Italy); IPCF-CNR, c/o Universita di Roma La Sapienza, 5 Piazzale Aldo Moro, I-00185 Roma (Italy); Seitsonen, Ari P. [Département de Chimie, Université de Zurich, Winterthurerstrasse 190, CH-8057 Zürich (Switzerland); Département de Chimie, École Normale Supérieure, 24 rue Lhomond, F-75005 Paris (France)

    2015-09-14

    Unlike phonons in crystals, the collective excitations in liquids cannot be treated as propagation of harmonic displacements of atoms around stable local energy minima. The viscoelasticity of liquids, reflected in transition from the adiabatic to elastic high-frequency speed of sound and in absence of the long-wavelength transverse excitations, results in dispersions of longitudinal (L) and transverse (T) collective excitations essentially different from the typical phonon ones. Practically, nothing is known about the effect of high pressure on the dispersion of collective excitations in liquids, which causes strong changes in liquid structure. Here dispersions of L and T collective excitations in liquid Li in the range of pressures up to 186 GPa were studied by ab initio simulations. Two methodologies for dispersion calculations were used: direct estimation from the peak positions of the L/T current spectral functions and simulation-based calculations of wavenumber-dependent collective eigenmodes. It is found that at ambient pressure, the longitudinal and transverse dynamics are well separated, while at high pressures, the transverse current spectral functions, density of vibrational states, and dispersions of collective excitations yield evidence of two types of propagating modes that contribute strongly to transverse dynamics. Emergence of the unusually high-frequency transverse modes gives evidence of the breakdown of a regular viscoelastic theory of transverse dynamics, which is based on coupling of a single transverse propagating mode with shear relaxation. The explanation of the observed high-frequency shift above the viscoelastic value is given by the presence of another branch of collective excitations. With the pressure increasing, coupling between the two types of collective excitations is rationalized within a proposed extended viscoelastic model of transverse dynamics.

  10. Statistical Investigations on Solar Wind Dynamic Pressure Pulses:Basic features and Their Impacts on Geosynchronous Magnetic Fields

    Science.gov (United States)

    Zuo, Pingbing; Feng, Xueshang

    2016-07-01

    Solar wind dynamic pressure pulse (DPP) structures, across which the dynamic pressure abruptly changes over timescales from a few seconds to several minutes, are often observed in the near-Earth space environment. Recently we have developed a novel procedure that is able to rapidly identify the DPPs from the plasma data stream, and simultaneously define the transition region and smartly select the upstream and downstream region for analysis. The plasma data with high time-resolution from 3DP instrument on board the WIND spacecraft are inspected with this automatic DPP-searching code, and a complete list of solar wind DPPs of historic WIND observations are built up. We perform a statistical survey on the properties of DPPs near 1 AU based on this event list. It is found that overwhelming majority of DPPs are associated with the solar wind disturbances including the CME-related flows, the corotating interaction regions, as well as the complex ejecta. The annual variations of the averaged occurrence rate of DPPs are roughly in phase with the solar activities. Although the variabilities of geosynchronous magnetic fields (GMFs) due to the impact of positive DPPs have been well established, there appears no systematic investigations on the response of GMFs to negative DPPs. Here we also study the decompression/compression effects of very strong negative/positive DPPs on GMFs under northward IMFs. In response to the decompression of strong negative DPPs, GMFs on dayside, near the dawn and dusk on nightside are generally depressed. But near the midnight region, the responses of GMF are very diverse, being either positive or negative. For part of events when GOES is located at the midnight sector, GMF is found to abnormally increase as the result of magnetospheric decompression caused by negative DPPs. It is known that on certain conditions magnetic depression of nightside GMFs can be caused by the impact of positive DPPs. Statistically, both the decompression effect of

  11. DYNAMIC ANALYSIS FOR THE DISCRETE PARTICLE MODEL BY DISTINCT ELEMENT METHOD : APPLICATION TO CALCULATION OF COEFFICIENT OF EARTH PRESSURE

    OpenAIRE

    大西, 泰史

    2017-01-01

    The purpose of this study is to perform to earth pressure coefficient calculation simulation using the Distinct Element Method (DEM). Earth pressure theory has been established since long ago and is still in use. Therefore, simulation based on Coulomb and Rankine's theory of earth pressure is carried out to confirm usability of DEM. As a result of the static earth pressure coefficient calculation simulation, good results were obtained. However, in the passive earth pressure coefficient calcul...

  12. Pressure dependence of elastic and dynamical properties of zinc-blende ZnS and ZnSe from first principle calculation

    Directory of Open Access Journals (Sweden)

    H.Y. Wang

    2012-03-01

    Full Text Available The density-functional theory (DFT and density-functional perturbation theory (DFPT are employed to study the pressure dependence of elastic and dynamical properties of zinc-blende ZnS and ZnSe. The calculated elastic constants and phonon spectra from 0 GPa to 15 GPa are compared with the available experimental data. Generally, our calculated values are overestimated with experimental data, but agree well with recent other theoretical values. The discrepancies with experimental data are due to the use of local density approximation (LDA and effect of temperature. In this work, in order to compare with experimental data, we calculated and discussed the pressure derivatives of elastic constants, the pressure dependence of dynamical effect charge, and mode Grüneisen parameter at Γ.

  13. Effect of head-down-tilt bed rest and hypovolemia on dynamic regulation of heart rate and blood pressure

    Science.gov (United States)

    Iwasaki, K. I.; Zhang, R.; Zuckerman, J. H.; Pawelczyk, J. A.; Levine, B. D.; Blomqvist, C. G. (Principal Investigator)

    2000-01-01

    Adaptation to head-down-tilt bed rest leads to an apparent abnormality of baroreflex regulation of cardiac period. We hypothesized that this "deconditioning response" could primarily be a result of hypovolemia, rather than a unique adaptation of the autonomic nervous system to bed rest. To test this hypothesis, nine healthy subjects underwent 2 wk of -6 degrees head-down bed rest. One year later, five of these same subjects underwent acute hypovolemia with furosemide to produce the same reductions in plasma volume observed after bed rest. We took advantage of power spectral and transfer function analysis to examine the dynamic relationship between blood pressure (BP) and R-R interval. We found that 1) there were no significant differences between these two interventions with respect to changes in numerous cardiovascular indices, including cardiac filling pressures, arterial pressure, cardiac output, or stroke volume; 2) normalized high-frequency (0.15-0.25 Hz) power of R-R interval variability decreased significantly after both conditions, consistent with similar degrees of vagal withdrawal; 3) transfer function gain (BP to R-R interval), used as an index of arterial-cardiac baroreflex sensitivity, decreased significantly to a similar extent after both conditions in the high-frequency range; the gain also decreased similarly when expressed as BP to heart rate x stroke volume, which provides an index of the ability of the baroreflex to alter BP by modifying systemic flow; and 4) however, the low-frequency (0.05-0.15 Hz) power of systolic BP variability decreased after bed rest (-22%) compared with an increase (+155%) after acute hypovolemia, suggesting a differential response for the regulation of vascular resistance (interaction, P < 0.05). The similarity of changes in the reflex control of the circulation under both conditions is consistent with the hypothesis that reductions in plasma volume may be largely responsible for the observed changes in cardiac

  14. Temporal resilience and dynamics of anaerobic methane-oxidizing microbial communities to short-term changes in methane partial pressures

    Science.gov (United States)

    Klasek, S.; Tiantian, Y.; Torres, M. E.; Colwell, F. S.; Wang, F.; Liang, L.

    2015-12-01

    Marine sediments produce tens to hundreds of teragrams of methane annually, which is released from the seabed at thousands of cold seeps distributed globally along continental margins. Around 80-90% of this methane is consumed in shallower sediment layers before reaching the hydrosphere, in a microbially-mediated process known as anaerobic oxidation of methane (AOM) However, cold seeps appear to exhibit temporal variation in gas flux intensity, and AOM filter efficiency at cold seeps generally decreases with fluid flow rate. To our knowledge, the degree to which temporal heterogeneity in subsurface methane flux stimulates AOM community growth and adaptation to increased methane concentrations has not been investigated. Static high-pressure bioreactors were used to incubate sulfate-methane transition zone (SMTZ) and methanogenic zone sediments underlying a Mediterranean mud volcano gas flare under in situ temperature and pressure at 8 MPa methane. Sulfide production rates of 0.4 μmol/cm3/day in both sediment regimes after 4 months of incubation suggested the resilience of the marine subsurface methane filter may extend well below the SMTZ (40 cm). Similar incubations of SMTZ samples from below a gas flare off Svalbard at saturating (3.8 MPa) and 0.2 MPa methane are being sampled after 1 week, 4 weeks, and 4 months; sulfide production rates of 8-18 nmol/cm3/day were first observed after 4 weeks of incubation. Sediment samples at all specified time points for both sets of incubations were collected for nucleic acid extraction and cell fixation. Anaerobic methanotrophic archaea (ANME) and sulfate-reducing bacteria (SRB) are expected dominant taxa in enriched and non-enriched communities. 16S rDNA community analysis is expected to reveal additional microbial players involved in the short-term adaptation to higher methane partial pressures in the marine subsurface. Increased AOM community activity (RNA/DNA ratio) and copy numbers of methane cycling transcripts (mcr

  15. The effects of plantar flexor static stretching and dynamic stretching using an aero-step on foot pressure during gait in healthy adults: a preliminary study.

    Science.gov (United States)

    Shim, Je-Myung; Jung, Ju-Hyeon; Kim, Hwan-Hee

    2015-07-01

    [Purpose] The aim of this study was to examine whether plantar flexor static stretching and dynamic stretching using an Aero-Step results in changes in foot pressure during gait in healthy adults. [Subjects] Eighteen normal adults were randomly allocated to either a dynamic stretching using an Aero-Step group (DSUAS) group (n = 8) or a static stretching (SS) group (n = 10). [Methods] The DSUAS and SS participants took part in an exercise program for 15 minutes. Outcome measures were foot plantar pressure, which was measured during the subject's gait stance phase; the asymmetric ratio of foot pressure for both feet; and the visual analogue scale (VAS) measured during the interventions. [Results] There were significant differences in the asymmetric ratio of foot pressure for both feet and VAS between the two groups after intervention. However, there were no significant differences in foot plantar pressure during the gait stance phase within both groups. [Conclusion] DSUSAS is an effective stretching method, as pain during it is lower than that with SS, which can minimize the asymmetric ratio of foot pressure for both feet during gait due to asymmetric postural alignment.

  16. Analysis of Mesoscopic Structured 2-Propanol/Water Mixtures Using Pressure Perturbation Calorimetry and Molecular Dynamic Simulation.

    Science.gov (United States)

    Bye, Jordan W; Freeman, Colin L; Howard, John D; Herz, Gregor; McGregor, James; Falconer, Robert J

    2017-01-01

    In this paper we demonstrate the application of pressure perturbation calorimetry (PPC) to the characterization of 2-propanol/water mixtures. PPC of different 2-propanol/water mixtures provides two useful measurements: (i) the change in heat (ΔQ); and (ii) the [Formula: see text] value. The results demonstrate that the ΔQ values of the mixtures deviate from that expected for a random mixture, with a maximum at ~20-25 mol% 2-propanol. This coincides with the concentration at which molecular dynamics (MD) simulations show a maximum deviation from random distribution, and also the point at which alcohol-alcohol hydrogen bonds become dominant over alcohol-water hydrogen bonds. Furthermore, the [Formula: see text] value showed transitions at 2.5 mol% 2-propanol and at approximately 14 mol% 2-propanol. Below 2.5 mol% 2-propanol the values of [Formula: see text] are negative; this is indicative of the presence of isolated 2-propanol molecules surrounded by water molecules. Above 2.5 mol% 2-propanol [Formula: see text] rises, reaching a maximum at ~14 mol% corresponding to a point where mixed alcohol-water networks are thought to dominate. The values and trends identified by PPC show excellent agreement not only with those obtained from MD simulations but also with results in the literature derived using viscometry, THz spectroscopy, NMR and neutron diffraction.

  17. Dynamic high pressure microfluidization-assisted extraction and bioactivities of Cyperus esculentus (C. esculentus L.) leaves flavonoids.

    Science.gov (United States)

    Jing, Siqun; Wang, Saisai; Li, Qian; Zheng, Lian; Yue, Li; Fan, Shaoli; Tao, Guanjun

    2016-02-01

    The aim of this work was to study the effect of dynamic high pressure microfluidization (DHPM) on extracting total flavonoids from Cyperus esculentus L. (C. esculentus L.) leaves and to evaluate the antioxidant activity and antibacterial property of these flavonoids. In all the assays, pretreatment with DHPM was found to not only efficiently improve the yield of total flavonoids but also strengthen the antioxidant activity of the total flavonoids. C. esculentus L. leaves flavonoids had pronounced antioxidant activity in vivo that could significantly elevate the content of superoxide dismutase (SOD) without increasing the malondialdehyde (MDA) levels, and could also improve total antioxidant capacity in mice with a dose-dependent fashion. C. esculentus L. leaves flavonoids inhibited the growth of both Gram positive and Gram negative bacteria while no obvious inhibitory effect on Penicillium and Aspergillus could be observed. Our studies indicate that flavonoids from C. esculentus L. leaves can be taken as a natural antioxidant and bacteriostatic substance in food and pharmaceutical industry.

  18. A molecular dynamics study of ambient and high pressure phases of silica: Structure and enthalpy variation with molar volume

    Science.gov (United States)

    Rajappa, Chitra; Sringeri, S. Bhuvaneshwari; Subramanian, Yashonath; Gopalakrishnan, J.

    2014-06-01

    Extensive molecular dynamics studies of 13 different silica polymorphs are reported in the isothermal-isobaric ensemble with the Parrinello-Rahman variable shape simulation cell. The van Beest-Kramer-van Santen (BKS) potential is shown to predict lattice parameters for most phases within 2%-3% accuracy, as well as the relative stabilities of different polymorphs in agreement with experiment. Enthalpies of high-density polymorphs - CaCl2-type, α-PbO2-type, and pyrite-type - for which no experimental data are available as yet, are predicted here. Further, the calculated enthalpies exhibit two distinct regimes as a function of molar volume—for low and medium-density polymorphs, it is almost independent of volume, while for high-pressure phases a steep dependence is seen. A detailed analysis indicates that the increased short-range contributions to enthalpy in the high-density phases arise not only from an increased coordination number of silicon but also shorter Si-O bond lengths. Our results indicate that amorphous phases of silica exhibit better optimization of short-range interactions than crystalline phases at the same density while the magnitude of Coulombic contributions is lower in the amorphous phase.

  19. Bubble Dynamics for Nucleate Pool Boiling of Water, Ethanol and Methanol Pure Liquids under the Atmospheric Pressure

    Directory of Open Access Journals (Sweden)

    samane hamzekhani

    2015-01-01

    Full Text Available Bubble dynamics is the most important sub-phenomenon, which basically affects the nucleate pool boiling heat transfer coefficient. In this research, bubble departure diameter values were experimentally measured for heat fluxes up to 110 kW.m-2. Experiments were carried out for pool boiling of pure liquids, including water, ethanol and methanol on a horizontal smoothed cylinder, at atmospheric pressure. For ethanol and methanol, rigid spherical bubbles with small contact area were observed. The spherical shapes seem to be because of small diameters.For all test fluids, experimental results show that bubble diameter increases with increasing heat flux. Most predictions have a similar trend for increasing bubble diameter versus increasing heat flux. Also, the existing well-known and most common used correlations are comparatively discussedwith the present experimental data. Finally, a new model for the prediction of vapor bubble departure diameter, based on Buckingham theory, in nucleate boiling is proposed, which predicts the experimental data with a satisfactory accuracy.

  20. Storage stability and antibacterial activity of eugenol nanoliposomes prepared by an ethanol injection-dynamic high-pressure microfluidization method.

    Science.gov (United States)

    Peng, Shengfeng; Zou, Liqiang; Liu, Wei; Gan, Lu; Liu, Weilin; Liang, Ruihong; Liu, Chengmei; Niu, Jing; Cao, Yanlin; Liu, Zhen; Chen, Xing

    2015-01-01

    Eugenol is a major phenolic component with diverse biological activities. However, it is difficult to formulate into an aqueous solution due to poor water solubility, and this limits its application. In the present study, eugenol nanoliposomes (EN) were prepared by combining the ethanol injection method with the dynamic high-pressure microfluidization method. Good physicochemical characterizations of EN were obtained. The successful encapsulation of eugenol in nanoliposomes was confirmed by Fourier transform infrared spectroscopy. A good storage stability of EN was confirmed by its low variation of average particle diameter and encapsulation efficiency after 8 weeks of storage. No oil drops were found in EN after 8 weeks of storage at 4°C and at room temperature, which suggested that the poor water solubility of eugenol was overcome by nanoliposome encapsulation. Compared with that of eugenol solution, a relatively good sustained release property was observed in EN. The antibacterial activity of EN against four common foodborne pathogenic bacteria (Staphylococcus aureus, Escherichia coli, Salmonella enterica serovar Typhimurium, and Listeria monocytogenes) was evaluated in both Luria broth and milk medium.

  1. Temperature-compensated distributed hydrostatic pressure sensor with a thin-diameter polarization-maintaining photonic crystal fiber based on Brillouin dynamic gratings.

    Science.gov (United States)

    Teng, Lei; Zhang, Hongying; Dong, Yongkang; Zhou, Dengwang; Jiang, Taofei; Gao, Wei; Lu, Zhiwei; Chen, Liang; Bao, Xiaoyi

    2016-09-15

    A temperature-compensated distributed hydrostatic pressure sensor based on Brillouin dynamic gratings (BDGs) is proposed and demonstrated experimentally for the first time, to the best of our knowledge. The principle is to measure the hydrostatic pressure induced birefringence changes through exciting and probing the BDGs in a thin-diameter pure silica polarization-maintaining photonic crystal fiber. The temperature cross-talk to the hydrostatic pressure sensing can be compensated through measuring the temperature-induced Brillouin frequency shift (BFS) changes using Brillouin optical time-domain analysis. A distributed measurement of hydrostatic pressure is demonstrated experimentally using a 4-m sensing fiber, which has a high sensitivity, with a maximum measurement error less than 0.03 MPa at a 20-cm spatial resolution.

  2. A Dynamic Pressure Component in UHP Whiteschists from the Dora-Maira Massif (Western Alps, Italy) Revealed By Pressure-Induced Incipient Amorphization of Quartz

    Science.gov (United States)

    Frezzotti, M. L.; Palmeri, R.; Godard, G.; Ferrando, S.; Compagnoni, R.

    2014-12-01

    We report the micro-Raman evidence for pressure-induced incipient amorphization of quartz in the UHP Brossasco-Isasca Unit (Dora-Maira Massif, Italian western Alps). Fifteen quartz inclusions in garnet were studied that comprise single crystals and aggregates of two-to-four crystals, along with one matrix crystal in a strain shadow. Palisade quartz, from coesite inversion, is also observed in garnet. The straight alignment of inclusions in prograde garnet indicates that quartz grew during garnet growth at about 650°C and 2.8 GPa, from HP to UHP metamorphic conditions. In single quartz crystals, disordering of lattice and densification (i.e., diaplectic glass) are revealed by two additional bands in Raman spectra: the former at 480 cm-1, derived from tetrahedral densified SiO2 amorphous phase composed of four-membered rings, and the latter at 605 cm-1, from defect structures involving partially broken SiO2 bonds. At the P-T metamorphic conditions of garnet growth, coesite is the thermodynamically stable form of crystalline silica. The existence of a lower enthalpy configuration, however, is a necessary but not sufficient condition for phase transition at constant pressure. If a kinetically accessible path is not available for the transition to ensue, metastable denser amorphous phase is formed instead. Amorphization of α-quartz requires experimental (or theoretical) lithostatic (hydrostatic) pressures > 15 GPa, while in presence of deviatoric stresses (i.e., non-lithostatic conditions), required pressures are lowered down to ≤ 5 GPa, at room temperature. Previous numerical geodynamic models suggested that in UHP terranes tectonic overpressure, greater than up to 0.3 GPa the lithostatic one, may be locally present (Gerya et al., 2008, Lithos, 103, 236-256). Our study confirms the presence of transitory pressure deviations from lithostatic values during prograde UHP metamorphism on a time scale that allows minerals to record these pressures.

  3. Dynamic characteristics of the cutaneous vasodilator response to a local external pressure application detected by the laser Doppler flowmetry technique on anesthetized rats

    Science.gov (United States)

    Humeau, Anne; Koitka, Audrey; Saumet, Jean-Louis; L'Huillier, Jean-Pierre

    2003-10-01

    The laser Doppler flowmetry technique has recently been used to report a significant transient increase of the cutaneous blood flow signal when a local non-noxious pressure is applied progressively on the skin (11.1 Pa/s). The present work analyses the dynamic characteristics of this vasodilatory reflex response on anaesthetised rats. A de-noising algorithm using wavelets is proposed to obtain accurate values of these dynamic characteristics. The blood flow peak and the time to reach this peak are computed on the de-noised recordings. The results show that the mean time to reach the peak of perfusion is 85.3 s (time t = 0 at the beginning of the pressure application). The mean peak value is 188.3 arbitrary units (a.u.), whereas the mean value of the perfusion before the pressure application is 113.4 a.u. The mean minimum value obtained at the end of the experiment is 60.7 a.u. This latter value is, on the average, reached 841.3 s after the beginning of the pressure application. The comparison of the dynamic characteristics, computed with the de-noising algorithm on signals obtained in other situations, will give a better understanding on some cutaneous lesions such as those present on diabetic people.

  4. Hemodynamic mechanisms of the attenuated blood pressure response to mental stress after a single bout of maximal dynamic exercise in healthy subjects

    Directory of Open Access Journals (Sweden)

    F.J. Neves

    2012-07-01

    Full Text Available To determine the hemodynamic mechanisms responsible for the attenuated blood pressure response to mental stress after exercise, 26 healthy sedentary individuals (age 29 ± 8 years underwent the Stroop color-word test before and 60 min after a bout of maximal dynamic exercise on a treadmill. A subgroup (N = 11 underwent a time-control experiment without exercise. Blood pressure was continuously and noninvasively recorded by infrared finger photoplethysmography. Stroke volume was derived from pressure signals, and cardiac output and peripheral vascular resistance were calculated. Perceived mental stress scores were comparable between mental stress tests both in the exercise (P = 0.96 and control (P = 0.24 experiments. After exercise, the blood pressure response to mental stress was attenuated (pre: 10 ± 13 vs post: 6 ± 7 mmHg; P 0.05. In conclusion, a single bout of maximal dynamic exercise attenuates the blood pressure response to mental stress in healthy subjects, along with lower stroke volume and cardiac output, denoting an acute modulatory action of exercise on the central hemodynamic response to mental stress.

  5. Analysis of wind-induced dynamic pressure fluctuations during one and a half Martian years at Gale Crater

    Science.gov (United States)

    Ullán, Aurora; Zorzano, María-Paz; Javier Martín-Torres, Francisco; Valentín-Serrano, Patricia; Kahanpää, Henrik; Harri, Ari-Matti; Gómez-Elvira, Javier; Navarro, Sara

    2017-05-01

    The Rover Environmental Monitoring Station (REMS) instrument on-board the Mars Science Laboratory (MSL) has acquired unprecedented measurements of key environmental variables at the base of Gale Crater. The pressure measured by REMS shows modulations with a very structured pattern of short-time scale (of the order of seconds to several minutes) mild fluctuations (typically up to 0.2 Pa at daytime and 1 Pa at night-time). These dynamic pressure oscillations are consistent with wind, air and ground temperature modulations measured simultaneously by REMS. We detect the signals of a repetitive pattern of upslope/downslope winds, with maximal speeds of about 21 m/s, associated with thermal changes in the air and surface temperatures, that are initiated after sunset and finish with sunrise proving that Gale, a 4.5 km deep impact crater, is an active Aeolian environment. At nighttime topographic slope winds are intense with maximal activity from 17:00 through 23:00 Local Mean Solar Time, and simultaneous changes of surface temperature are detected. During the day, the wind modulations are related to convection of the planetary boundary layer, winds are softer with maximum wind speed of about 14 m/s. The ground temperature is modulated by the forced convection of winds, with amplitudes between 0.2 K and 0.5 K, and the air temperatures fluctuate with amplitudes of about 2 K. The analysis of more than one and a half Martian years indicates the year-to-year repeatability of these environmental phenomena. The wind pattern minimizes at the beginning of the south hemisphere winter (Ls 90) season and maximizes during late spring and early summer (Ls 270). The procedure that we present here is a useful tool to investigate in a semi-quantitative way the winds by: i) filling both seasonal and diurnal gaps where wind measurements do not exist, ii) providing an alternative way for comparisons through different measuring principia and, iii) filling the gap of observation of short

  6. Pressure dependence of harmonic and an harmonic lattice dynamics in MgO: A first-principles calculation and implications for lattice thermal conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Xiaoli [Physics Department, Auburn University, Auburn, Alabama (United States); Dong, Jianjun [Physics Department, Auburn University, Auburn, Alabama (United States)

    2009-06-01

    We report a recent first-principles calculation of harmonic and anharmonic lattice dynamics of MgO. The 2nd order harmonic and 3rd order anharmonic interatomic interaction terms are computed explicitly, and their pressure dependences are discussed. The phonon mode Grueneisen parameters derived based on our calculated 3rd order lattice anharmonicity are in good agreement with those estimated using the finite difference method. The implications for lattice thermal conductivity at high pressure are discussed based on a simple kinetic transport theory.

  7. Driven evolution of a constitutional dynamic library of molecular helices toward the selective generation of [2 x 2] gridlike arrays under the pressure of metal ion coordination.

    Science.gov (United States)

    Giuseppone, Nicolas; Schmitt, Jean-Louis; Lehn, Jean-Marie

    2006-12-27

    Constitutional dynamics, self-assembly, and helical-folding control are brought together in the efficient Sc(OTf)3/microwave-catalyzed transimination of helical oligohydrazone strands, yielding highly diverse dynamic libraries of interconverting constituents through assembly, dissociation, and exchange of components. The transimination-type mechanism of the ScIII-promoted exchange, as well as its regioselectivity, occurring only at the extremities of the helical strands, allow one to perform directional terminal polymerization/depolymerization processes when starting with dissymmetric strands. A particular library is subsequently brought to express quantitatively [2 x 2] gridlike metallosupramolecular arrays in the presence of ZnII ions by component recombination generating the correct ligand from the dynamic set of interconverting strands. This behavior represents a process of driven evolution of a constitutional dynamic chemical system under the pressure (coordination interaction) of an external effector (metal ions).

  8. A New Model for Predicting Dynamic Surge Pressure in Gas and Drilling Mud Two-Phase Flow during Tripping Operations

    Directory of Open Access Journals (Sweden)

    Xiangwei Kong

    2014-01-01

    Full Text Available Investigation of surge pressure is of great significance to the circulation loss problem caused by unsteady operations in management pressure drilling (MPD operations. With full consideration of the important factors such as wave velocity, gas influx rate, pressure, temperature, and well depth, a new surge pressure model has been proposed based on the mass conservation equations and the momentum conservation equations during MPD operations. The finite-difference method, the Newton-Raphson iterative method, and the fourth-order explicit Runge-Kutta method (R-K4 are adopted to solve the model. Calculation results indicate that the surge pressure has different values with respect to different drill pipe tripping speeds and well parameters. In general, the surge pressure tends to increase with the increases of drill pipe operating speed and with the decrease of gas influx rate and wellbore diameter. When the gas influx occurs, the surge pressure is weakened obviously. The surge pressure can cause a significant lag time if the gas influx occurs at bottomhole, and it is mainly affected by pressure wave velocity. The maximum surge pressure may occur before drill pipe reaches bottomhole, and the surge pressure is mainly affected by drill pipe operating speed and gas influx rate.

  9. Development of a Dynamic Biomechanical Model for Load Carriage: Phase 4, Part C3: Dynamic Assessment of Pressure Measurement Systems for Use in Human Load Carriage

    Science.gov (United States)

    2005-08-01

    technology by Tekscan , Inc., a capacitance-based technology by Novel, Inc., and XSENSOR® Technology Inc., and a piezoresistive technology by Vista...Vista Medical Inc), a pneumatic pressure sensor (Talley Pressure Monitor 3), and a Tekscan ‘seat’ 2056 sensor array. The abstract, however, neglected to...coefficients of variance for linearity ranging from 1.9%-9.9% using a Flexiforce system; a low pressure detection sensor by Tekscan Inc. As well

  10. Consolidation and dynamics of 3D unsaturated porous seabed under rigid caisson breakwater loaded by hydrostatic pressure and wave

    Institute of Scientific and Technical Information of China (English)

    YE JianHong; JENG DongSheng; CHAN A H C

    2012-01-01

    In this study,based on the dynamic Biot's theory "u-p" approximation,a 3D finite element method (FEM) numerical soil model is developed,in which the Generalized Newmark-β method is adopted to determine the time integration.The developed 3D FEM soil model is a part of the coupled model PORO-WSSI 3D for 3D wave-seabed-marine structures interaction problem,and is validated by the analytical solution proposed by Wang (2000) for a laterally infinite seabed loaded by a uniform force.By adopting the developed 3D soil model,the consolidation of seabed under a caisson breakwater and hydrostatic pressure is investigated.The numerical results show that the caisson breakwater built on seabed has very significant effect on the stresses/displacements fields in the seabed foundation after the transient deformation and primary consolidation are completed.The parametric study indicates that the Young's modulus E of seabed is the most important parameter to affect the settlement of breakwater,and the displacement fields in seabed foundation.Taking the consolidation status as the initial condition,the interaction between ocean wave,caisson breakwater and seabed foundation is briefly investigated.The 3D ocean wave is determined by solving the Navier-Stokes equations with finite volume method (FVM).The numerical results indicate that there is intensive interaction between ocean wave,caisson breakwater and seabed foundation; and the breakwater indeed can effectively block the wave energy propagating to the coastline.

  11. Molecular dynamics analysis of multiphase interfaces based on in situ extraction of the pressure distribution of a liquid droplet on a solid surface.

    Science.gov (United States)

    Nishida, S; Surblys, D; Yamaguchi, Y; Kuroda, K; Kagawa, M; Nakajima, T; Fujimura, H

    2014-02-21

    Molecular dynamics simulations of a nanoscale liquid droplet on a solid surface are carried out in order to examine the pressure tensor field around the multiphase interfaces, and to explore the validity of Young's equation. By applying the virial theorem to a hemicylindrical droplet consisting of argon molecules on a solid surface, two-dimensional distribution of the pressure tensor is obtained. Tensile principal pressure tangential to the interface is observed around the liquid-vapor transition layer, while both tensile and compressive principal pressure tangential to the interface exists around the solid-liquid transition layer due to the inhomogeneous density distribution. The two features intermix inside the overlap region between the transition layers at the contact line. The contact angle is evaluated by using a contour line of the maximum principal pressure difference. The interfacial tensions are calculated by using Bakker's equation and Young-Laplace equation to the pressure tensor distribution. The relation between measured contact angle and calculated interfacial tensions turns out to be consistent with Young's equation, which is known as the description of the force balance at the three-phase interface.

  12. Numerical Investigation of Dynamic Rock Fracture Toughness Determination Using a Semi-Circular Bend Specimen in Split Hopkinson Pressure Bar Testing

    Science.gov (United States)

    Xu, Y.; Dai, F.; Xu, N. W.; Zhao, T.

    2016-03-01

    The International Society for Rock Mechanics (ISRM) has suggested a notched semi-circular bend technique in split Hopkinson pressure bar (SHPB) testing to determine the dynamic mode I fracture toughness of rock. Due to the transient nature of dynamic loading and limited experimental techniques, the dynamic fracture process associated with energy partitions remains far from being fully understood. In this study, the dynamic fracturing of the notched semi-circular bend rock specimen in SHPB testing is numerically simulated for the first time by the discrete element method (DEM) and evaluated in both microlevel and energy points of view. The results confirm the validity of this DEM model to reproduce the dynamic fracturing and the feasibility to simultaneously measure key dynamic rock fracture parameters, including initiation fracture toughness, fracture energy, and propagation fracture toughness. In particular, the force equilibrium of the specimen can be effectively achieved by virtue of a ramped incident pulse, and the fracture onset in the vicinity of the crack tip is found to synchronize with the peak force, both of which guarantee the quasistatic data reduction method employed to determine the dynamic fracture toughness. Moreover, the energy partition analysis indicates that simplifications, including friction energy neglect, can cause an overestimation of the propagation fracture toughness, especially under a higher loading rate.

  13. Perilymphatic pressure dynamics following posture change in patients with Menière's disease and in normal hearing subjects.

    Science.gov (United States)

    Rosingh, H J; Wit, H P; Albers, F W

    1998-01-01

    The hydrostatic pressure of the inner ear depends on the cerebrospinal fluid pressure through the cochlear aqueduct. The time-course of inner ear pressure change following rapid change in cerebrospinal fluid pressure is related to the aqueduct patency. In this study the patency of the cochlear aqueduct in 27 patients with Menière's disease (28 affected ears, 16 non-affected ears) and in 12 normal hearing subjects (18 control ears) was assessed non-invasively by means of the MMS-10 Tympanic Displacement Analyser. Following a rapid change in body position, changes in intracranial cerebrospinal fluid pressure were found to influence perilymphatic pressure within 1 min. No significant differences were found among affected ears, non-affected ears and control ears.

  14. Self-consistent system of equations for a kinetic description of the low-pressure discharges accounting for the nonlocal and collisionless electron dynamics.

    Science.gov (United States)

    Kaganovich, Igor D; Polomarov, Oleg

    2003-08-01

    In low-pressure discharges, where the electron mean free path is larger or comparable with the discharge length, the electron dynamics is essentially nonlocal. Moreover, the electron energy distribution function (EEDF) deviates considerably from a Maxwellian. Therefore, an accurate kinetic description of the low-pressure discharges requires knowledge of the nonlocal conductivity operator and calculation of the non-Maxwellian EEDF. The previous treatments made use of simplifying assumptions: a uniform density profile and a Maxwellian EEDF. In the present study, a self-consistent system of equations for the kinetic description of nonlocal, nonuniform, nearly collisionless plasmas of low-pressure discharges is derived. It consists of the nonlocal conductivity operator and the averaged kinetic equation for calculation of the non-Maxwellian EEDF. The importance of accounting for the nonuniform plasma density profile on both the current density profile and the EEDF is demonstrated.

  15. Fiber optic LDF to monitor vascular dynamics of urticarial dermographism in pressure-tested patients before and after treatment with antihistamines

    Science.gov (United States)

    Eikje, Natalja Skrebova; Arase, Seiji

    2008-02-01

    The local microcirculatory dynamics underlying phenomenon of urticarial dermographism (UD) are not yet sufficiently elucidated in dermatological patients. A fiber optic laser Doppler flowmeter (LDF) was used to monitor skin blood flow (SBF) changes on the back of the patients with UD before and after application of the series of pressure stimuli (9.8×10 4, 14.7×10 4, 19.6×10 4 and 24.5×10 4 Pa). All patients acted as self-controls to assess their disease activity by means of SBF values based on response to pressure stimuli before and after treatment with antihistamines, when compared to baseline SBF. Throughout 30 minutes evaluation inter-subject SBF values at pressure-tested sites were noticeably distinguished as high, moderate and low. By LDF we could differentiate the highest development of vascular dynamics after 5 minutes, coming back to normal within about 30 minutes in one group of patients, and the vascular dynamics reaching its maximum in 15 minutes, but with no fade after 30 minutes, in another group of patients. All treatment regimens in both groups of patients by LDF produced a measurable reduction already during 1-2 days of therapy, accompanied by a reduction in SBF baseline values in patients with severe and moderate symptoms of UD.

  16. THE EFFECT OF SYSTEM TEMPERATURE AND PRESSURE ON THE FLUID-DYNAMIC BEHAVIOR OF THE SUPERCRITICAL ANTISOLVENT MICRONIZATION PROCESS: A NUMERICAL APPROACH

    Directory of Open Access Journals (Sweden)

    R. A. Almeida

    Full Text Available Abstract The Supercritical Antisolvent (SAS technique allows for the precipitation of drugs and biopolymers in nanometer size in a wide range of industrial applications, while guaranteeing the physical and chemical integrity of such materials. However, a suitable combination of operating parameters is needed for each type of solute. The knowledge of fluid dynamics behavior plays a key role in the search for such parameter combinations. This work presents a numerical study concerning the impact of operating temperature and pressure upon the physical properties and mixture dynamics within the SAS process, because in supercritical conditions the radius of the droplets formed exhibits great sensitivity to these variables. For the conditions analyzed, to account for the heat of mixture in the energy balance, subtle variations in the temperature fields were observed, with almost negligible pressure drop. From analyses of the intensity of segregation, there is an enhancement of the mixture on the molecular scale when the system is operated at higher pressure. This corroborates experimental observations from the literature, related to smaller diameters of particles under higher pressures. Hence, the model resulted in a versatile tool for selecting conditions that may promote a better control over the performance of the SAS process.

  17. Lattice Dynamics Study of Phonon Instability and Thermal Properties of Type-I Clathrate K8Si46 under High Pressure

    Directory of Open Access Journals (Sweden)

    Wei Zhang

    2016-07-01

    Full Text Available For a further understanding of the phase transitions mechanism in type-I silicon clathrates K8Si46, ab initio self-consistent electronic calculations combined with linear-response method have been performed to investigate the vibrational properties of alkali metal K atoms encapsulated type-I silicon-clathrate under pressure within the framework of density functional perturbation theory. Our lattice dynamics simulation results showed that the pressure induced phase transition of K8Si46 was believed to be driven by the phonon instability of the calthrate lattice. Analysis of the evolution of the partial phonon density of state with pressure, a legible dynamic picture for both guest K atoms and host lattice, was given. In addition, based on phonon calculations and combined with quasi-harmonic approximation, the specific heat of K8Si46 was derived, which agreed very well with experimental results. Also, other important thermal properties including the thermal expansion coefficients and Grüneisen parameters of K8Si46 under different temperature and pressure were also predicted.

  18. Research on inversion high mining pressure distribution and technol-ogy of preventing dynamic disasters by MS monitoring in longwall face

    Institute of Scientific and Technical Information of China (English)

    CHENG Yun-hai; JIANG Fu-xing; ZOU Yin-hui

    2009-01-01

    Under two rock strata combination conditions, over 10,000 microseismic events were received with microseismic location monitoring technology which possessed by the author's studying team, used in fully mechanized coal face of Huafeng Mine of Xinwen Coal Mining Group Co., Shandong Province. On the basis of the achievement of the loca-tion results, the conclusions were drawn as follows: On the basis of the achievement of 3D strata fracturing situation and the section plane of microseimic events in different areas, the relationship between spatial structure of overlying strata and mining pressure field was found, and we might describe distribution range of dynamic pressure of advance pressure and lateral stress around long face, and range of structure ad-tivation. Quantitative guid-ance to prevent dynamic disasters was provided. The practice in coal mine got a effective results. According to the FLAC3D soft numerical simulation of diameter drilling hole (the diameter is 300 mm) to relieve pressure in specified geological condition in Huafeng Mine, the right distance of two dirlls is 2.5 m and the right depth is 12 m. The research pro-vided basic guiding and practical experiences for the underground microseismic monitoring and disaster prevention in side slopes or tunnels engineering.

  19. 考虑围压效应的高土石坝动力响应分析%Dynamic Response of High Rockfill Dam Considering Confining Pressure Effect

    Institute of Scientific and Technical Information of China (English)

    曹学兴; 何蕴龙; 熊堃; 冯蕊; 王超; 岑威钧

    2014-01-01

    Experimental results show that the dynamic properties of rockfill are strongly dependent on confining pres-sure effect. Therefore,it is very necessary to consider confining pressure effect in the seismic calculation and analysis of high rockfill dam. The relationship between dynamic shear modulus and dynamic shear strain and that between damping ratio and dynamic shear strain were improved on the basis of widely used Hardin-Drnevich constitutive model in this paper. Then a new model considering confining pressure effect was established. The new model can well simulate the dynamic properties of rockfill of a practical project under various confining pressures. A correspond-ing computational procedure was compiled and applied in the dynamic response analysis of Changheba dam. The dy-namic response features and the permanent deformation of the dam were obtained,which could provide the reference for engineering design.%试验结果表明土石材料的动力特性参数有很强的围压依赖性,所以在高土石坝动力计算分析中考虑围压效应是十分必要的。在广泛应用的Hardin-Drnevich本构模型的基础上,提出了改进动剪切模量与动剪应变关系式及阻尼比与动剪应变关系式的方法,得到一个可以考虑围压效应的改进模型,与实际工程试验曲线对比结果表明,新模型可以较好地模拟土石料在各个围压下的动力特性。根据新模型编制相应计算程序并应用于长河坝高土石坝地震动力反应分析中,得到了大坝整体动力反应规律与大坝地震永久变形,为工程设计提供参考。

  20. Space Shuttle Main Engine Low Pressure Oxidizer Turbo-Pump Inducer Dynamic Environment Characterization through Water Model and Hot-Fire Testing

    Science.gov (United States)

    Arellano, Patrick; Patton, Marc; Schwartz, Alan; Stanton, David

    2006-01-01

    The Low Pressure Oxidizer Turbopump (LPOTP) inducer on the Block II configuration Space Shuttle Main Engine (SSME) experienced blade leading edge ripples during hot firing. This undesirable condition led to a minor redesign of the inducer blades. This resulted in the need to evaluate the performance and the dynamic environment of the redesign, relative to the current configuration, as part of the design acceptance process. Sub-scale water model tests of the two inducer configurations were performed, with emphasis on the dynamic environment due to cavitation induced vibrations. Water model tests were performed over a wide range of inlet flow coefficient and pressure conditions, representative of the scaled operating envelope of the Block II SSME, both in flight and in ground hot-fire tests, including all power levels. The water test hardware, facility set-up, type and placement of instrumentation, the scope of the test program, specific test objectives, data evaluation process and water test results that characterize and compare the two SSME LPOTP inducers are discussed. In addition, dynamic characteristics of the two water models were compared to hot fire data from specially instrumented ground tests. In general, good agreement between the water model and hot fire data was found, which confirms the value of water model testing for dynamic characterization of rocket engine turbomachinery.

  1. The particle image velocimetry method in the study of the dynamics of phase transitions induced by high pressures in triolein and oleic acid

    Science.gov (United States)

    Tefelski, D. B.; Kulisiewicz, L.; Wierschem, A.; Delgado, A.; Rostocki, A. J.; Siegoczyński, R. M.

    2011-03-01

    Particle image velocimetry (PIV) is an optical measurement method capable of providing visualisation of velocity field of particle flow in fluids. After analysis of data acquired in the form of an image sequence, it is possible to retrieve information about flow parameters as mean values of velocity, vorticity, shear and normal strain. This paper presents the results of high pressure experiments using this method applied to triolein and oleic acid samples in their phase transition region. A high pressure optical chamber, He-Ne laser and light-sheet optics together with a digital camera and image acquisition computer allow us to study the motion of particles in high pressure conditions. The set-up was similar to that presented in Özmutlu et al. [Momentum and energy transfer during phase change of water under high hydrostatic pressure, Innov. Food Sci. Emerg. Technol. 7(3) (2006), pp. 161-168] and Kulisiewicz et al. [Visualization of pressure-shift freezing and thawing of concentrated aqueous sucrose solutions, High Press. Res. 27(2) (2007), pp. 291-297]. The analysis of phase transition dynamics in triolein and oleic acid is an extension to the work presented in Tefelski et al. [The investigation of the dynamics of the phase transformation in triolein and oleic acid under pressure, J. Phys.: Conf. Ser. 121(142004) (2008), pp. 1-6]. Oleic acid is a monounsaturated fatty acid and has a bent rod shape. Triolein is a triglyceride and has a "chair"-like shape. It is the base particle of many vegetable oils, especially olive oil. Triolein consists of three chains of oleic acid bound by a glycerol part. Information obtained by the study of phase transitions dynamics is important for food science and food technology processes which involve high pressure treatment. The PIV method shows differences in the solidification process of both substances in time, the existence of inhomogeneities (layers of different densities in the observed flow) and allows us to calculate the

  2. Flat feet, happy feet? Comparison of the dynamic plantar pressure distribution and static medial foot geometry between Malawian and Dutch adults.

    Directory of Open Access Journals (Sweden)

    Niki M Stolwijk

    Full Text Available In contrast to western countries, foot complaints are rare in Africa. This is remarkable, as many African adults walk many hours each day, often barefoot or with worn-out shoes. The reason why Africans can withstand such loading without developing foot complaints might be related to the way the foot is loaded. Therefore, static foot geometry and dynamic plantar pressure distribution of 77 adults from Malawi were compared to 77 adults from the Netherlands. None of the subjects had a history of foot complaints. The plantar pressure pattern as well as the Arch Index (AI and the trajectory of the center of pressure during the stance phase were calculated and compared between both groups. Standardized pictures were taken from the feet to assess the height of the Medial Longitudinal Arch (MLA. We found that Malawian adults: (1 loaded the midfoot for a longer and the forefoot for a shorter period during roll off, (2 had significantly lower plantar pressures under the heel and a part of the forefoot, and (3 had a larger AI and a lower MLA compared to the Dutch. These findings demonstrate that differences in static foot geometry, foot loading, and roll off technique exist between the two groups. The advantage of the foot loading pattern as shown by the Malawian group is that the plantar pressure is distributed more equally over the foot. This might prevent foot complaints.

  3. Flat feet, happy feet? Comparison of the dynamic plantar pressure distribution and static medial foot geometry between Malawian and Dutch adults.

    Science.gov (United States)

    Stolwijk, Niki M; Duysens, Jacques; Louwerens, Jan Willem K; van de Ven, Yvonne Hm; Keijsers, Noël Lw

    2013-01-01

    In contrast to western countries, foot complaints are rare in Africa. This is remarkable, as many African adults walk many hours each day, often barefoot or with worn-out shoes. The reason why Africans can withstand such loading without developing foot complaints might be related to the way the foot is loaded. Therefore, static foot geometry and dynamic plantar pressure distribution of 77 adults from Malawi were compared to 77 adults from the Netherlands. None of the subjects had a history of foot complaints. The plantar pressure pattern as well as the Arch Index (AI) and the trajectory of the center of pressure during the stance phase were calculated and compared between both groups. Standardized pictures were taken from the feet to assess the height of the Medial Longitudinal Arch (MLA). We found that Malawian adults: (1) loaded the midfoot for a longer and the forefoot for a shorter period during roll off, (2) had significantly lower plantar pressures under the heel and a part of the forefoot, and (3) had a larger AI and a lower MLA compared to the Dutch. These findings demonstrate that differences in static foot geometry, foot loading, and roll off technique exist between the two groups. The advantage of the foot loading pattern as shown by the Malawian group is that the plantar pressure is distributed more equally over the foot. This might prevent foot complaints.

  4. Effects of pressure, temperature and atomic exchanges on phase separation dynamics in Au/Ni(111) surface alloy: Kinetic Monte Carlo study

    Energy Technology Data Exchange (ETDEWEB)

    Zvejnieks, G. [Institute for Solid State Physics, University of Latvia, Kengaraga 8, LV-1063 Riga (Latvia); Ibenskas, A., E-mail: ibenskas@pfi.lt [Center for Physical Sciences and Technology, Semiconductor Physics Institute, Gostauto 11, LT-01108 Vilnius (Lithuania); Tornau, E.E. [Center for Physical Sciences and Technology, Semiconductor Physics Institute, Gostauto 11, LT-01108 Vilnius (Lithuania)

    2015-11-15

    Instability of the Au/Ni(111) surface alloy is studied in different CO gas pressure, p, and temperature limits using kinetic Monte Carlo simulations. We analyze the reaction front dynamics and formation of Au clusters using the model which takes into account surface adatom pair and three-body interactions, CO adsorption and desorption, catalytic carbonyl formation reaction, Au and Ni adatom diffusion and their concerted exchange. Variation of interaction parameters allows us to identify three possible reaction front propagation limits with different pressure dependencies: (i) slow channel-like flow in agreement with experimental data [1] (step flow rate, R, increases with p), (ii) intermediate regime (weak p–dependence), and (iii) fast homogeneous flow (R decreases with p). We find that only Au–Ni exchange, contrary to both Ni–CO and Au–CO exchanges, significantly reduces the number of screened Ni atoms inside the Au clusters and stimulates the occurrence of Ni-free Au clusters. The size of Au islands depends on both pressure and temperature. At a fixed temperature it decreases with pressure due to an increased step flow rate. In the high temperature limit, despite the step flow rate exponential increase with temperature, the cluster size increases due to an enhanced Au mobility. - Highlights: • Kinetic Monte Carlo study of Au–Ni surface alloy instability to CO pressure and temperature. • Three reaction front propagation regimes. • In channel-like regime, the step flow rate increases with CO pressure as in experiment. • Ni-free Au islands are obtained when Au-Ni adatom exchange mechanism is considered. • The size of Au islands decreases with pressure and increases with temperature.

  5. Transient dynamics study on casing deformation resulted from lost circulation in low-pressure formation in the Yuanba Gasfield, Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Chen Shen

    2015-10-01

    Full Text Available In the course of completion of an ultra-deep well newly drilled in the Yuanba Gasfield, Sichuan Basin, long-section and large-scale deformation occurred in the heavy casing section and nickel base alloy casing section of the sealing Triassic limestone interval, so a new hole had to be sidetracked, which impels us to rediscover the applicability of conventional drilling and completion technology in ultra-deep wells. In this paper, based on the borehole condition and field operation data of this well, the borehole pressure field variation initiated by lost circulation in the low-pressure formation was analyzed from the perspective of dynamics, then, the variation pattern of differential pressure inside and outside the well bore at different time intervals was depicted, and the primary cause of such complication was theoretically revealed, i.e., the pressure wave generated by instant lost circulation in low-pressure formation would result in redistribution of pressure inside the downhole confined space, and then the crush of casing in the vicinity of local low-pressure areas. Pertinent proposals for avoiding these kinds of engineering complexities were put forward: ① when downhole sealing casing operation is conducted in open hole completion, liner completion or perforated hole, the potential damage of lost circulation to casing should be considered; ② the downhole sealing point and sealing mode should be selected cautiously: the sealing point had better be selected in the section with good cementing quality or as close to the casing shoe as possible, and the sealing mode can be either cement plug or mechanical bridge plug. This paper finally points out that good cementing quality plays an important role in preventing this type of casing deformation.

  6. Mechanically induced strong red emission in samarium ions doped piezoelectric semiconductor CaZnOS for dynamic pressure sensing and imaging

    Science.gov (United States)

    Wang, Wei; Peng, Dengfeng; Zhang, Hanlu; Yang, Xiaohong; Pan, Caofeng

    2017-07-01

    Piezoelectric semiconductor with optical, electrical and mechanical multifunctions has great potential applications in future optoelectronic devices. The rich properties and applications mainly encompass the intrinsic structures and their coupling effects. Here, we report that lanthanide ions doped piezoelectric semiconductor CaZnOS:Sm3+ showing strong red emission induced by dynamic mechanical stress. Under moderate mechanical load, the doped piezoelectric semiconductor exhibits strong visible red emission to the naked eyes even under the day light. A flexible dynamic pressure sensor device is fabricated based on the prepared CaZnOS:Sm3+ powders. The mechanical-induced emission properties of the device are investigated by the optical fiber spectrometer. The linear characteristic emissions are attributed to the 4G5/2→6H5/2 (566 nm), 4G5/2→6H7/2 (580-632 nm), 4G5/2→6H9/2 (653-673 nm) and 4G5/2→6H11/2 (712-735 nm) f-f transitions of Sm3+ ions. The integral emission intensity is proportional to the value of applied pressure. By using the linear relationship between integrated emission intensity and the dynamic pressure, the real-time pressure distribution is visualized and recorded. Our results highlight that the incorporation of lanthanide luminescent ions into piezoelectric semiconductors as smart materials could be applied into the flexible mechanical-optical sensor device without additional auxiliary power, which has great potential for promising applications such as mapping of personalized handwriting, smart display, and human machine interface.

  7. Development of a new dynamic gas flow-control system in the pressure range of 1 Pa-133 Pa

    Energy Technology Data Exchange (ETDEWEB)

    Hong, S. S.; Chung, J. W. [Korea Research Institute of Standards and Science, Daejeon 305-340 (Korea, Republic of); Khan, Wakil [Pakistan Vacuum Society, street 17, Islamabad (Pakistan)

    2011-12-15

    A new flow-control system (FCS-705) has been developed at Korea Research Institute of Standards and Science. The system is intended for calibration of vacuum gauges in the pressure range of 1 Pa-133 Pa by comparison method. This paper describes some basic characteristics of the system including; (1) the design and construction of the system, (2) the generation of stable pressures in the chamber, (3) achieving high upstream pressure limit by installing a short duct in the by-pass pumping line, and (4) investigation of the gas flow regimes within the short duct.

  8. The disproportionation reaction phase transition, mechanical, and lattice dynamical properties of the lanthanum dihydrides under high pressure: A first principles study

    Science.gov (United States)

    Yang, Jin-Wen; Gao, Tao; Gong, Yan-Rong

    2014-06-01

    The pressure-induced disproportionation reaction phase transition, mechanical, and dynamical properties of LaH2 with fluorite structure under high pressure are investigated by performing first-principles calculations using the projector augmented wave (PAW) method. The phase transition of 2LaH2 → LaH + LaH3 obtained from the usual condition of equal enthalpies occurs at the pressure of 10.38 GPa for Perdew-Wang (PW91) functional and 6.05 GPa for Ceperly-Adler (CA) functional, respectively. The result shows that the PW91 functional calculations agree excellently with the experimental finding of 11 GPa of synchrotron radiation (SR) X-ray diffraction (XRD) of Machida et al. and 10 GPa of their PBE functional theoretical result. Three independent single-crystal elastic constants, polycrystalline bulk modulus, shear modulus, Young's modulus, elastic anisotropy, Poisson's ratio, the brittle/ductile characteristics and elastic wave velocities over different directions dependences on pressure are also successfully obtained. Especially, the phonon dispersion curves and corresponding phonon density of states of LaH2 under high pressure are determined systematically using a linear-response approach to density functional perturbation theory (DFPT). Our results demonstrate that LaH2 in fluorite phase can be stable energetically up to 10.38 GPa, stabilized mechanically up to 17.98 GPa, and stabilized dynamically up to 29 GPa, so it may remain a metastable phase above 10.38 GPa up to 29 GPa, these calculated results accord with the recent X-Ray diffraction experimental finding and theoretical predictions of Machida et al.

  9. 地震激励下的储罐动压力理论分析%Theoretical Analysis of Storage Tanks' Dynamic Pressure under Earthquake Excitation

    Institute of Scientific and Technical Information of China (English)

    李敏; 张霖; 李洪明

    2013-01-01

    Both research findings and methods for the tanks' seismic design were summarized, then the tanks' dynamic pressure under horizontal and vertical earthquake excitation at the same time was analyzed theoretically, i. e. assuming the liquid in the tank is inviscid, irrotational and incompressible, and then to solve Laplace equation under given boundary conditions and make the tank wall' s pressure meet the Bernoulli equation; having the inertial force, uncoupling pulse pressure caused by storage tank vibration and the convection pressure from the liquid shaking respectively considered and the superposition principle based to get analytic e-quation of the dynamic pressure storage tank.%概述了储罐在抗震设计问题上已经取得的研究成果和方法.继此研究成果之后,对同时受到水平和竖直地震激励作用下的储罐动压力进行理论分析.即假定储罐内的液体为无粘、无旋、不可压缩的理想液体,在给定的边界条件下求解拉普拉斯方程,并使得罐壁压力满足线性贝努力方程.分别考虑储罐惯性力、罐液藕连振动产生的脉冲压力以及液面晃动产生的对流压力等各部分产生的压力,最后由叠加原理得到储罐动压力的解析表达式.

  10. Implications for anomalous mantle pressure and dynamic topography from lithospheric stress patterns in the North Atlantic Realm

    DEFF Research Database (Denmark)

    Schiffer, Christian; Nielsen, Søren Bom

    2016-01-01

    -established thin sheet model in a global finite element representation. We adjust the lithospheric thickness and the sub-lithospheric pressure iteratively, comparing modelled in plane stress with the observations of the World Stress Map. We find that an anomalous mantle pressure associated with the Iceland...... of a buoyancy anomaly at the base of the North Atlantic lithosphere at or slightly before continental breakup, relatively fast dissipation of the fringes of this, and continued melt generation below Iceland....

  11. Temperature-pressure-induced solid-solid to reorientation in FCC metallic nanowire: a molecular dynamic study.

    Science.gov (United States)

    Sutrakar, Vijay Kumar; Roy Mahapatra, D; Pillai, A C R

    2012-01-11

    Atomistic simulation of initial oriented FCC Cu nanowires shows a novel coupled temperature-pressure dependent reorientation from to phase. A temperature-pressure-induced solid-solid to reorientation diagram is generated for Cu nanowire with varying cross-sectional sizes. A critical pressure is reported for Cu nanowires with varying cross-sectional sizes, above which an initial oriented nanowire shows temperature independent reorientation into the phase. The effect of surface stresses on the to reorientation is also studied. The results indicate that above a critical cross-sectional size for a given temperature-pressure, to reorientation is not possible. It is also reported here that for a given applied pressure, an increase in temperature is required for the to reorientation with increasing cross-sectional size of the nanowire. The temperature-pressure-induced solid-solid to reorientation diagram reported in the present paper could further be used as guidelines for controlling the reorientations/shape memory in nano-scale applications of FCC metallic nanowires.

  12. A transmission-line model of back-cavity dynamics for in-plane pressure-differential microphones.

    Science.gov (United States)

    Kim, Donghwan; Kuntzman, Michael L; Hall, Neal A

    2014-11-01

    Pressure-differential microphones inspired by the hearing mechanism of a special parasitoid fly have been described previously. The designs employ a beam structure that rotates about two pivots over an enclosed back volume. The back volume is only partially enclosed due to open slits around the perimeter of the beam. The open slits enable incoming sound waves to affect the pressure profile in the microphone's back volume. The goal of this work is to study the net moment applied to pressure-differential microphones by an incoming sound wave, which in-turn requires modeling the acoustic pressure distribution within the back volume. A lumped-element distributed transmission-line model of the back volume is introduced for this purpose. It is discovered that the net applied moment follows a low-pass filter behavior such that, at frequencies below a corner frequency depending on geometrical parameters of the design, the applied moment is unaffected by the open slits. This is in contrast to the high-pass filter behavior introduced by barometric pressure vents in conventional omnidirectional microphones. The model accurately predicts observed curvature in the frequency response of a prototype pressure-differential microphone 2 mm × 1 mm × 0.5 mm in size and employing piezoelectric readout.

  13. [Dynamic measurement of pressure distribution with flexible measuring mats--an innovative measuring procedure in sports orthopedics and traumatology. Development--use--value].

    Science.gov (United States)

    Schaff, P; Hauser, W

    1987-12-01

    The results of this study provide the basis for an on-target use of measurement of pressure distribution with flexible mats in sports orthopaedics and traumatology and adjacent overlapping fields. Dynamic measurement of pressure distribution using a flexible mat as a capacitor can yield valuable additional information not available so far in this form, on the static and dynamic stress acting on the human locomotor system. In the future this method can be used to prevent injuries and to optimise performance in many disciplines of sport and will make a significant contribution to optimised treatment concepts with pressure-adjusted shoes or insoles, as well as to the control of functional surgery results in traumatology. The fundamentals are presented via a detailed description of the development, standardization and testing of this innovative measuring method. The questions of applicability, practicability and information supplied are discussed on the basis of extensive studies on reproducibility, on the amount of time and technical effort required for each measurement, and on a critical comparison with other methods. For the two fields of application presented here it was possible to standardize the working procedure enabling a largely problem-free application in practice. The first useful results were obtained in sports orthopaedics (alpine ski boots and sportshoe design). By applying the measuring of pressure distribution in alpine ski sports the influence the construction of ski boots on the stress exercised on the human leg could be objectively quantified in man for the first time. Marked differences were found between models where the heel can be turned down on entering, to conventionally fastened ski boots. This, as well as the results on the influence temperature, height of shaft and shaft stability or rigidity on the pressure distribution along the tibia, provide the basis for a new guideline for the testing of ski boots. A new method was developed for the

  14. Dynamic characteristics of laser Doppler flowmetry signals obtained in response to a local and progressive pressure applied on diabetic and healthy subjects

    Science.gov (United States)

    Humeau, Anne; Koitka, Audrey; Abraham, Pierre; Saumet, Jean-Louis; L'Huillier, Jean-Pierre

    2004-09-01

    In the biomedical field, the laser Doppler flowmetry (LDF) technique is a non-invasive method to monitor skin perfusion. On the skin of healthy humans, LDF signals present a significant transient increase in response to a local and progressive pressure application. This vasodilatory reflex response may have important implications for cutaneous pathologies involved in various neurological diseases and in the pathophysiology of decubitus ulcers. The present work analyses the dynamic characteristics of these signals on young type 1 diabetic patients, and on healthy age-matched subjects. To obtain accurate dynamic characteristic values, a de-noising wavelet-based algorithm is first applied to LDF signals. All the de-noised signals are then normalised to the same value. The blood flow peak and the time to reach this peak are then calculated on each computed signal. The results show that a large vasodilation is present on signals of healthy subjects. The mean peak occurs at a pressure of 3.2 kPa approximately. However, a vasodilation of limited amplitude appears on type 1 diabetic patients. The maximum value is visualised, on the average, when the pressure is 1.1 kPa. The inability for diabetic patients to increase largely their cutaneous blood flow may bring explanations to foot ulcers.

  15. Dynamic Strength and Fracturing Behavior of Single-Flawed Prismatic Marble Specimens Under Impact Loading with a Split-Hopkinson Pressure Bar

    Science.gov (United States)

    Li, Xibing; Zhou, Tao; Li, Diyuan

    2017-01-01

    Dynamic impact tests are performed on prismatic marble specimens containing a single flaw using a modified split-Hopkinson pressure bar device. The effects of pre-existing flaws with different flaw angles and lengths on the dynamic mechanical properties are analyzed. The results demonstrate that the dynamic strength of marble is influenced by the flaw geometry. The dynamic fracturing process of flawed specimens is monitored and characterized with the aid of a high-speed camera. Cracking of marble specimens with a single pre-existing flaw under impact loading is analyzed based on experimental investigations. Cracking involves two major stages: formation of white patches and development of macrocracks. Six typical crack types are identified on the basis of their trajectories and initiation mechanisms. The presence of an artificial flaw may change the failure mode of marble from splitting-dominated for an intact specimen to shear-dominated for a flawed specimen under dynamic loading. Nevertheless, the geometry of the flaws appears to have a slight influence on the failure modes of flawed specimens under impact loading.

  16. 自动标准压力发生器动态控制准确度分析%Dynamic Control Accuracy Analysis of Automatic Digital Pressure Controller

    Institute of Scientific and Technical Information of China (English)

    李海兵; 麻锐; 卓华; 陈武卿

    2014-01-01

    An additional uncertainty of pressure generators can be introduced to account for control precision. This additional precision is on-ly needed when the controls are in dynamic mode and the operator is using the front panel to display. Herein a calculation method of control preci-sion is displayed for PACE6000 serials pressure generators. It is assumed that a piston gauge is used as standard while a high-precision digital pressure gauge is applied as reference, and when 0.01-class pressure calibrator is used as standard, the uncertainty analysis of 0.05-class digital pressure gauge is shown, and the MPEV ( maximum permissible error value) of inlet-pressure transducer must be ±0.008%.%自动标准压力发生器(以下简称发生器)性能的一个重要指标是准确度。当发生器处于动态控制模式及使用面板显示时需要考虑附加控制准确度。本文通过对PACE6000系列的发生器进行比对实验,以活塞式压力计为标准器,高准确度数字压力计为参考对象,得出了其控制准确度,最后给出了以0.01级数字压力发生器为标准器、0.05级数字压力计示值误差的测量不确定度分析,其内置压力传感器的最大允许误差须为依0.008%。

  17. Experimental study on pressure, stress state, and temperature-dependent dynamic behavior of shear thickening fluid subjected to laser induced shock

    Science.gov (United States)

    Wu, Xianqian; Yin, Qiuyun; Huang, Chenguang

    2015-11-01

    The dynamic response of the 57 vol./vol. % dense spherical silica particle-polyethylene glycol suspension at high pressure was investigated through short pulsed laser induced shock experiments by measuring the back free surface velocities of aluminum-shear thickening fluid (STF)-aluminum assembled targets. The results showed that the attenuation behavior of shock wave in the STF was dependent on shock pressure, stress state, and test temperature. The measured back free particle velocities of the targets and shock wave velocities in the STF decreased with the decrease in shock pressure while shocked at the same stress state and the same test temperature. In addition, two types of dragging mechanisms in the STF were observed while shocked at different stress states. For a uniaxial strain state, the impact induced jamming behavior in the STF is the dragging mechanism for the attenuation of shock wave, and a critical shock pressure was required for the impact induced thickening behavior. However, while the shock wave transformed from a uniaxial strain state to a dilatation state after transmitted to a certain distance, beside the dragging effect of impact induced jamming behavior, a strong dragging effect, induced by shear induced thickening behavior, was also observed.

  18. Dynamic osseous scintigraphy in the knee hyper-pressure syndromes; Scintigraphie osseuse dynamique dans les syndrome d`hyperpression du genou

    Energy Technology Data Exchange (ETDEWEB)

    Laurin, J.; Jau, P.; Ferro, L.; Fouque, M. [Clinique Clairval, 317 Bd du Redon, 13009 Marseille (France)

    1997-12-31

    This retrospective study of 49 patients, carrying an internal mono-compartmental algic syndrome of the knee, determines the place of the dynamical osseous scintigraphy in three times: in comparison with the pan-goniometry (for 42 of them), in the diagnosis of the hyper-pressure syndrome and in the evaluation of its severity. The vascularization is augmented in 10 patients and the sanguinary pool in 14. Forty eight internal compartments exhibit a tracer hyper-fixation at late times. These anomalies have been classified according to their tibial or condylar localization and intensity, than compared with the pan-goniometric values of the deviation, which in case of a varus, entail an over-pressure risk. These comparisons show a good correlation between the hyper-fixation in the sub-chondral band of the internal tibial plateau and a syndrome of hyper-pressure by deviation in varus, whether this hyper-fixation was moderated and isolated or severe or associated to a condylar image; the intensity of the fixation indicates the severity. The tibial fixation intensity is always superior to that of the rest of compartment, what is essential for the differential diagnosis in case of a simple, without hyper-pressure, arthritis, or other pathology. From this exploration stem 8 osteotomies and 1 prosthesis

  19. Dynamic terahertz spectroscopy of gas molecules mixed with unwanted aerosol under atmospheric pressure using fibre-based asynchronous-optical-sampling terahertz time-domain spectroscopy.

    Science.gov (United States)

    Hsieh, Yi-Da; Nakamura, Shota; Abdelsalam, Dahi Ghareab; Minamikawa, Takeo; Mizutani, Yasuhiro; Yamamoto, Hirotsugu; Iwata, Tetsuo; Hindle, Francis; Yasui, Takeshi

    2016-06-15

    Terahertz (THz) spectroscopy is a promising method for analysing polar gas molecules mixed with unwanted aerosols due to its ability to obtain spectral fingerprints of rotational transition and immunity to aerosol scattering. In this article, dynamic THz spectroscopy of acetonitrile (CH3CN) gas was performed in the presence of smoke under the atmospheric pressure using a fibre-based, asynchronous-optical-sampling THz time-domain spectrometer. To match THz spectral signatures of gas molecules at atmospheric pressure, the spectral resolution was optimized to 1 GHz with a measurement rate of 1 Hz. The spectral overlapping of closely packed absorption lines significantly boosted the detection limit to 200 ppm when considering all the spectral contributions of the numerous absorption lines from 0.2 THz to 1 THz. Temporal changes of the CH3CN gas concentration were monitored under the smoky condition at the atmospheric pressure during volatilization of CH3CN droplets and the following diffusion of the volatilized CH3CN gas without the influence of scattering or absorption by the smoke. This system will be a powerful tool for real-time monitoring of target gases in practical applications of gas analysis in the atmospheric pressure, such as combustion processes or fire accident.

  20. Effect of ambient gas pressure on pulsed laser ablation plume dynamics and ZnTe film growth

    Energy Technology Data Exchange (ETDEWEB)

    Rouleau, C.M.; Lowndes, D.H.; Geohegan, D.B.; Allard, L.F. [Oak Ridge National Lab., TN (United States); Strauss, M.A.; Cao, S.; Pedraza, A.J. [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Materials Science and Engineering; Puretzky, A.A. [Inst. of Spectroscopy, Troitsk (Russian Federation)

    1995-12-01

    Epitaxial thin films of nitrogen-doped p-ZnTe were grown on single-crystal, semi-insulating Ga-As substrates via pulsed laser ablation of a stoichiometric ZnTe target. Both low pressure nitrogen ambients and high vacuum were used. Results of in situ reflection high energy electron diffraction (RHEED) and time-resolved ion probe measurements have been compared with ex situ Hall effect and transmission electron microscopy (TEM) measurements. A strong correlation was observed between the nature of the film`s surface during growth (2-D vs. 3-D, assessed via RHEED) and the ambient gas pressures employed during deposition. The extended defect content (assessed via cross-sectional TEM) in the region >150 mn from the film/substrate interface was found to increase with the ambient gas pressure during deposition, which could not be explained by lattice mismatch alone. At sufficiently high pressures, misoriented, columnar grains developed which were not only consistent with the RHEED observations but also were correlated with a marked decrease in Hall mobility and a slight decrease in hole concentration. Ion probe measurements, which monitored the attenuation and slowing of the ion current arriving at the substrate surface, indicated that for increasing nitrogen pressure the fast (vacuum) velocity distribution splits into a distinct fast and two collisionally-slowed components or modes. Gas controlled variations in these components mirrored trends in electrical properties and microstructural measurements.

  1. Plasma dynamics and cations off-stoichiometry in LaAlO3 films grown in high pressures regimes

    Science.gov (United States)

    Sambri, A.; Khare, Amit; Mirabella, S.; Di Gennaro, E.; Safeen, Akif; Di Capua, F.; Campajola, L.; Scotti di Uccio, U.; Amoruso, S.; Miletto Granozio, F.

    2016-12-01

    The indirect effect of oxygen background gas on the La/Al ratio during the growth of LaAlO3 (LAO) films by pulsed laser deposition (PLD) is analyzed, in a pressure range between 10-3 and 10-1 mbar. We resort to two complementary investigation methods: Rutherford backscattering spectroscopy and spectrally resolved, time-gated imaging of the laser plume. The first technique allows us to analyze the stoichiometry of the deposited films, and the latter allows us to analyze the plume expansion phase of the PLD process by collecting chemically resolved two-dimensional images of the relevant atomic/molecular species. The comparison between the results obtained by the two techniques allows us to highlight the role of the plume-gas interaction in affecting cations stoichiometry. Our results indicate that, in the considered pressure range, the background oxygen pressure affects the cations stoichiometry of the LAO films, besides determining their oxygen content.

  2. First-principles investigations on structural, elastic, dynamical, and thermal properties of earth-abundant nitride semiconductor CaZn{sub 2}N{sub 2} under pressure

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Ying-Qin; Liu, Lei; Cheng, Yan [Sichuan Univ. (China). College of Physical Science and Technology; Hu, Cui E. [Chongqing Normal Univ. (China). College of Physics and Electronic Engineering; Cai, Ling-Cang [CAEP, Mianyang (China). National Key Laboratory for Shock Wave and Detonation Physics Research

    2017-04-01

    We presented a detailed first-principal calculation to study the structural, elastic, dynamical, and thermal properties of a new synthetic ternary zinc nitride semiconductors CaZn{sub 2}N{sub 2} using the generalised gradient approximation (GGA) method. The obtained lattice parameters of CaZn{sub 2}N{sub 2} at 0 K and 0 GPa are in good agreement with the experimental data and other theoretical findings. The pressure dependences of the elastic constants C{sub ij} together with other derived mechanical properties of CaZn{sub 2}N{sub 2} compound have also been systematically investigated. The results reveal that CaZn{sub 2}N{sub 2} is mechanically stable up to 20 GPa. The calculated the phonon curves and phonon density of states under different pressures indicate that the CaZn{sub 2}N{sub 2} compound maintains its dynamical stability up to 20 GPa. An analysis in terms of the irreducible representations of group theory obtained the optical vibration modes of this system, and we obtained the frequencies of the optical vibrational modes at Γ points together with the atoms that contributed to these vibrations of CaZn{sub 2}N{sub 2}. Meanwhile, the pressure dependencies of the frequencies Raman-active and IR-active modes at 0-20 GPa have been studied. The quasi-harmonic approximation (QHA) was applied to calculate the thermal properties of CaZn{sub 2}N{sub 2} as functions of pressures and temperatures such as the heat capacity, thermal expansions, the entropy, and Grueneisen parameter γ.

  3. 测压管路动态特性实测技术研究%Study on measurement technology of dynamics characteristics of typical tubes for pressure measurements

    Institute of Scientific and Technical Information of China (English)

    余世策; 韩新刚; 冀晓华; 屠荣伟; 蒋建群

    2012-01-01

    利用声音振动发生原理研制了多功能声音振动发生装置,开发了测压管路动态特性的实测技术,并对风洞试验中典型测压管路的频响特性进行了实测.采用正弦压力波对不同的测压管路进行激励,采用多点联合扫描技术提高采样频率,得到完整的正弦波动曲线.实验研究结果表明,该实验技术可以得到高频的动态压力信号和准确的频响特性曲线,为误差修正提供了依据.%By using independently developed sound vibration generating device, the measurement technology of dynamics characteristics of typical tubes for pressure measurements was developed, and the frequency response characteristics of typical tubes for fluctuating wind pressure measurements were measured. By using principle of sound vibrations, a multi-function sound vibration generating device was developed. Different pipes were excited by sine pressure waves, multi-point scanning technology was used to improve the sampling frequency for getting full curves of sine waves. Experimental results show that the experimental technique developed can be ' used to obtain high-frequency dynamic pressure signals and accurate frequency response curve for providing a basis for the error correction.

  4. Prediction of the dynamic oscillation threshold in a clarinet model with a linearly increasing blowing pressure : Influence of noise

    CERN Document Server

    Bergeot, Baptiste; Vergez, Christophe; Gazengel, Bruno

    2013-01-01

    This paper presents an analysis of the effects of noise and precision on a simplified model of the clarinet driven by a variable control parameter. In a previous work [5], the dynamic oscillation threshold of a simplified model of a clarinet is obtained analytically. In the present article, the sensitivity of the dynamic threshold on precision is analyzed as a stochastic variable introduced in the model. A new theoretical expression is given for the dynamic thresholds in presence of the stochastic variable, providing a fair prediction of the thresholds found in finite-precision simulations. The dynamic thresholds are found to depend on increase rate and are independent on the initial value of the parameter, both in simulations and in theory.

  5. A Note on the Constant Pressure Phase in an Orthodox Gun with Moderated Charges using Hydro-Dynamical Model

    Directory of Open Access Journals (Sweden)

    D. K. Narvilkar

    1988-01-01

    Full Text Available The existing work on the constant pressure guns has been improved upon by introducing the concept of Lagrange mean density function for the propellant gases behind the shot. Lagrange hydrodynamical model has been considered and the expressions have been established to work out the shape factor of the second component of the moderated charge, which will maintain a constant pressure during the burning of this component. This is followed by the numerical computations of a problem to establish the physical interpretation of the results.

  6. Pressure-Driven DNA in Nanogroove Arrays: Complex Dynamics Leads to Length- and Topology-Dependent Separation

    DEFF Research Database (Denmark)

    Mikkelsen, Morten Bo Lindholm; Reisner, Walter; Flyvbjerg, Henrik

    2011-01-01

    The motion of linear and circular DNA molecules is studied under pressure driven buffer flow in a 50 nm slit channel with arrays of transverse 150 nm deep nanogrooves. Transport occurs through two states of propagation unique to this nanogroove geometry, a slow, stepwise groove-to-groove translat......The motion of linear and circular DNA molecules is studied under pressure driven buffer flow in a 50 nm slit channel with arrays of transverse 150 nm deep nanogrooves. Transport occurs through two states of propagation unique to this nanogroove geometry, a slow, stepwise groove...

  7. Asymptotic behavior and dynamic stability of phase mixtures for the equations of Navier Stokes with nonmonotonic pressure

    Science.gov (United States)

    Tsyganov, Eugene

    2007-09-01

    We investigate the asymptotic behavior of the solutions of the compressible Navier Stokes equations with nonmonotonic pressure when the initial data is large and discontinuous. We provide sufficient conditions on the pressure function for different boundary-value problems that guarantee strong convergence of the volume variable as time approaches infinity and show that, typically, fairly arbitrary discontinuous static phase mixtures can be realized as time-asymptotic limits from smooth initial data. It is required in the analysis that we improve known existence theories, which typically have small data or time-dependent bounds.

  8. A molecular view on a polyaniline–TiO{sub 2} nanostructured thin film: Effect of temperature and pressure on the thermal, mechanical, and dynamical properties

    Energy Technology Data Exchange (ETDEWEB)

    Bahramian, Alireza, E-mail: bahramian@aut.ac.ir

    2015-10-01

    The present work adopts experimental studies and molecular dynamics (MD) simulations to investigate the thermal, mechanical, and dynamical properties of polyaniline (PANI) coated on a TiO{sub 2} nanostructured film. At first, a series of the PANI and TiO{sub 2} nanostructured thin films were prepared using the sol–gel dip-coating method. The dynamic mechanical thermal analysis (DMTA) was used to measure glass transition temperature, T{sub g}. AFM-based nano-indentation tests were used to determine the values of hardness, Young's modulus and Poisson's ratio of the prepared thin films. Second, MD simulations were performed using COMPASS force field associated with energy minimization approach. The density and free energy profiles were calculated to determine the molecular structure and thermodynamic equilibrium state of the simulated PANI structures with different monomer chains at various temperatures. The value of T{sub g} of the PANI film under different pressures was also determined from the simulation. The mechanical properties of PANI film and the PANI–TiO{sub 2} interface such as the normal stresses, tangential stresses, surface tension, bulk and shear modulus and Poisson's ratio were determined computationally. The dynamic properties of simulated films were studied by the terms of torsion time autocorrelation function. In all cases, MD simulation results were in good to excellent agreement with the experimental data. - Highlights: • Polyaniline (PANI) and TiO{sub 2} thin films were prepared using the sol–gel dip-coating method. • The dynamical and mechanical properties of the PANI nanostructured film were investigated. • AFM-based nano-indentation tests were used to determine Young's modulus values. • The physical properties of the PANI and PANI–TiO{sub 2} interface were studied computationally. • Molecular dynamics simulation results were in good agreement with the experimental data.

  9. 动压法合成金刚石的发展史①--动压合成金刚石之一%Development History of Diamond Synthesis by Dynamic Pressure Technique---synthetic diamond by dynamic pressure technique NO.1

    Institute of Scientific and Technical Information of China (English)

    张书达

    2014-01-01

    This article expounds the development histroy of the diamond synthesis.By the inspiration of the earliest discovery of diamond from meteorite,people started to research on diamond synthesis by dynamic pressure technique.The development and perspective of the dynamic pressure technique in diamond industry in China has also been discussed in this article.%文章论述了最早人们从陨石中发现金刚石,并从中受到启发,开始研究通过动态高压的方法合成金刚石的发展历程,并论述了我国金刚石行业动态高压法合成的发展和前景。

  10. Dynamics of the atmospheric pressure diffuse dielectric barrier discharge between cylindrical electrodes in roll-to-roll PECVD reactor

    Science.gov (United States)

    Starostin, Sergey A.; Welzel, Stefan; Liu, Yaoge; van der Velden-Schuermans, Bernadette; Bouwstra, Jan B.; van de Sanden, Mauritius C. M.; de Vries, Hindrik W.

    2015-07-01

    The high current diffuse dielectric barrier discharge (DBD) was operated in a bi-axial cylindrical electrode configuration using nitrogen, oxygen and argon gas flow with the addition of tetraethyl orthosilicate as precursor for silica-like film deposition. The behaviour of the transient plasma was visualized by means of fast imaging from two orthogonal directions. The formation and propagation (~3 × 104 m s-1) of lateral ionization waves with the transverse light emission structure similar to the low pressure glow discharge was observed at time scales below 1 µs. Despite plasma non-uniformity at nanosecond time scale the deposition process on the web-rolled polymer results in smooth well adherent films with good film uniformity and excellent gas diffusion barrier properties. Contribution to the topical issue "The 14th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XIV)", edited by Nicolas Gherardi, Ronny Brandenburg and Lars Stollenwark

  11. Assessment of Dynamic Flow, Pressure and Geomechanical Behaviour of a CO2 Storage Complex

    DEFF Research Database (Denmark)

    Mbia, Ernest Ncha; Frykman, Peter

    it will be of great environmental concern especially to the ground water and other subsurface resources implying that quantifying pressure changes in CO2 sites is very important for monitoring purposes in order to prevent this phenomenon. Large scale CO2 storage has previously been considered for the Vedsted...... where the brine-fresh water interface resides need to be investigated and quantified through simulation studies as part of site qualification, as overpressure can push brine into the fresh water zone and thereby affecting aquifer performance. In order to estimate the sealing potential and rock...... on resulting permeability of deeply buried shale. The second part of this project is focused on assessing two scenarios including sensitivity of caprock permeability and compressibility on pressure development and transmission to the shallower Chalk Group where the brine-fresh water interface resides due...

  12. Institutional pressures, dynamic capabilities and environmental management systems: investigating the ISO 9000--environmental management system implementation linkage.

    Science.gov (United States)

    Zhu, Qinghua; Cordeiro, James; Sarkis, Joseph

    2013-01-15

    We hypothesize a model where domestic and international institutional pressures lead to the successful implementation of ISO 9000 and can in turn lead to the successful implementation of environmental management systems such as ISO 14001 environmental certification systems or total quality environmental management (TQEM) systems. Using appropriate tests for mediation with dichotomous mediators and outcomes, we find that the model holds for a sample of 377 Chinese manufacturers in six major industrial groups in Suzhou, Dalian, and Tianjin. Our findings are consistent with the theory linking internal capabilities to heterogeneous external (in this case, institutional) pressures on organizations for environmentally proactive efforts. Our findings suggest that institutions in developing countries with significant environmental concerns such as China as well as foreign suppliers and partners to firms in these countries should encourage and support ISO 9000 implementations by local firms. These findings may influence other developing nations' adoption of quality and environmental process systems.

  13. Simultaneous monitoring of static and dynamic intracranial pressure parameters from two separate sensors in patients with cerebral bleeds: comparison of findings

    Directory of Open Access Journals (Sweden)

    Eide Per

    2012-09-01

    Full Text Available Abstract Background We recently reported that in an experimental setting the zero pressure level of solid intracranial pressure (ICP sensors can be altered by electrostatics discharges. Changes in the zero pressure level would alter the ICP level (mean ICP; whether spontaneous changes in mean ICP happen in clinical settings is not known. This can be addressed by comparing the ICP parameters level and waveform of simultaneous ICP signals. To this end, we retrieved our recordings in patients with cerebral bleeds wherein the ICP had been recorded simultaneously from two different sensors. Materials and Methods: During a time period of 10 years, 17 patients with cerebral bleeds were monitored with two ICP sensors simultaneously; sensor 1 was always a solid sensor while Sensor 2 was a solid -, a fluid - or an air-pouch sensor. The simultaneous signals were analyzed with automatic identification of the cardiac induced ICP waves. The output was determined in consecutive 6-s time windows, both with regard to the static parameter mean ICP and the dynamic parameters (mean wave amplitude, MWA, and mean wave rise time, MWRT. Differences in mean ICP, MWA and MWRT between the two sensors were determined. Transfer functions between the sensors were determined to evaluate how sensors reproduce the ICP waveform. Results Comparing findings in two solid sensors disclosed major differences in mean ICP in 2 of 5 patients (40%, despite marginal differences in MWA, MWRT, and linear phase magnitude and phase. Qualitative assessment of trend plots of mean ICP and MWA revealed shifts and drifts of mean ICP in the clinical setting. The transfer function analysis comparing the solid sensor with either the fluid or air-pouch sensors revealed more variable transfer function magnitude and greater differences in the ICP waveform derived indices. Conclusions Simultaneous monitoring of ICP using two solid sensors may show marked differences in static ICP but close to identity

  14. Dynamic development characteristics of amounts of gas and levels of pressure in the Pan-1 coal mine of Huainan

    Institute of Scientific and Technical Information of China (English)

    WANG Ke-xin; FU Xue-hai; ZHOU Ya-nan; HE Ye; WU Heng

    2009-01-01

    The Pan-1 coal mine located in Huainan municipality, Anhui province, is abundant in coal resources. In order to discover the natural conditions of gas in its coal seams, we inverted the burial history of these coal seams using the software of Easy%Ro method and simulated the development process of gas volumes and pressure of the major coal seams using CBMHistory Simulation Software. Our analysis shows that the devolution of gas volumes and levels of pressure can be divided into four stages: I.e., a biogas stage (P1-P3), a pyrolysis gas stage (T1-T2), an active gas enrichment stage (T3-K1) and a gas dissipating stage (K2-present). Cur-rently, the average amounts of gas and gas pressure in coal seams Nos. 13-1,11-2 and 8 of the Pan-1 coal mine are 8.18 m3/t and 2.20 Mpa; 3.89 m3/t and 2.47 Mpa and 6.35 m3/t and 2.89 Mpa, respectively. This agrees very well with current mining data.

  15. Observation of in situ oxidation dynamics of vanadium thin film with ambient pressure X-ray photoemission spectroscopy

    Science.gov (United States)

    Kim, Geonhwa; Yoon, Joonseok; Yang, Hyukjun; Lim, Hojoon; Lee, Hyungcheol; Jeong, Changkil; Yun, Hyungjoong; Jeong, Beomgyun; Crumlin, Ethan; Lee, Jouhahn; Lee, Jaeyoung; Ju, Honglyoul; Mun, Bongjin Simon

    2016-11-01

    The evolution of oxidation/reduction states of vanadium oxide thin film was monitored in situ as a function of oxygen pressure and temperature via ambient pressure X-ray photoemission spectroscopy. Spectra analysis showed that VO2 can be grown at a relatively low temperature, T ˜ 523 K, and that V2O5 oxide develops rapidly at elevated oxygen pressure. Raman spectroscopy was applied to confirm the formation of VO2 oxide inside of the film. In addition, the temperature-dependent resistivity measurement on the grown thin film, e.g., 20 nm exhibited a desirable metal-insulator transition of VO2 with a resistivity change of ˜1.5 × 103 times at 349.3 K, displaying typical characteristics of thick VO2 film, e.g., 100 nm thick. Our results not only provide important spectroscopic information for the fabrication of vanadium oxides, but also show that high quality VO2 films can be formed at relatively low temperature, which is highly critical for engineering oxide film for heat-sensitive electronic devices.

  16. The role of the dissipative and random forces in the calculation of the pressure of simple fluids with dissipative particle dynamics

    CERN Document Server

    Goicochea, A Gama; Hernández, J D; Pérez, E

    2014-01-01

    The role of viscous forces coupled with Brownian forces in momentum conserving computer simulations is studied here in the context of their contribution to the total average pressure of a simple fluid as derived from the virial theorem, in comparison with the contribution of the conservative force to the total pressure. The specific mesoscopic model used is the one known as dissipative particle dynamics, although our conclusions apply to similar models that obey the fluctuation dissipation theorem for short range interactions and have velocity dependent viscous forces. We find that the average contribution of the random and dissipative forces to the pressure is negligible for long simulations, provided these forces are appropriately coupled and when the finite time step used in the integration of the equation of motion is not too small. Finally, we study the properties of the fluid when the random force is made equal to zero and find that the system freezes as a result of the competition of the dissipative an...

  17. Shear thinning and shear dilatancy of liquid n-hexadecane via equilibrium and nonequilibrium molecular dynamics simulations: Temperature, pressure, and density effects

    Science.gov (United States)

    Tseng, Huan-Chang; Wu, Jiann-Shing; Chang, Rong-Yeu

    2008-07-01

    Equilibrium and nonequilibrium molecular dynamics (MD) simulations have been performed in both isochoric-isothermal (NVT) and isobaric-isothermal (NPT) ensemble systems. Under steady state shearing conditions, thermodynamic states and rheological properties of liquid n-hexadecane molecules have been studied. Between equilibrium and nonequilibrium states, it is important to understand how shear rates (γ˙) affect the thermodynamic state variables of temperature, pressure, and density. At lower shear rates of γ˙1×1011s-1, specific behavior of shear dilatancy is observed in the variations of nonequilibrium thermodynamic states. Significantly, by analyzing the effects of changes in temperature, pressure, and density on shear flow system, we report a variety of rheological properties including the shear thinning relationship between viscosity and shear rate, zero-shear-rate viscosity, rotational relaxation time, and critical shear rate. In addition, the flow activation energy and the pressure-viscosity coefficient determined through Arrhenius and Barus equations acceptably agree with the related experimental and MD simulation results.

  18. Salt partitioning between water and high-pressure ices. Implication for the dynamics and habitability of icy moons and water-rich planetary bodies

    Science.gov (United States)

    Journaux, Baptiste; Daniel, Isabelle; Petitgirard, Sylvain; Cardon, Hervé; Perrillat, Jean-Philippe; Caracas, Razvan; Mezouar, Mohamed

    2017-04-01

    Water-rich planetary bodies including large icy moons and ocean exoplanets may host a deep liquid water ocean underlying a high-pressure icy mantle. The latter is often considered as a limitation to the habitability of the uppermost ocean because it would limit the availability of nutrients resulting from the hydrothermal alteration of the silicate mantle located beneath the deep ice layer. To assess the effects of salts on the physical properties of high-pressure ices and therefore the possible chemical exchanges and habitability inside H2O-rich planetary bodies, we measured partitioning coefficients and densities in the H2O-RbI system up to 450 K and 4 GPa; RbI standing as an experimentally amenable analog of NaCl in the H2O-salt solutions. We measured the partitioning coefficient of RbI between the aqueous fluid and ices VI and VII, using in-situ Synchrotron X-ray Fluorescence (XRF). With in-situ X-ray diffraction, we measured the unit-cell parameters and the densities of the high-pressure ice phases in equilibrium with the aqueous fluid, at pressures and temperatures relevant to the interior of planetary bodies. We conclude that RbI is strongly incompatible towards ice VI with a partitioning coefficient Kd(VI-L) = 5.0 (± 2.1) ṡ10-3 and moderately incompatible towards ice VII, Kd(VII-L) = 0.12 (± 0.05). RbI significantly increases the unit-cell volume of ice VI and VII by ca. 1%. This implies that RbI-poor ice VI is buoyant compared to H2O ice VI while RbI-enriched ice VII is denser than H2O ice VII. These new experimental results might profoundly impact the internal dynamics of water-rich planetary bodies. For instance, an icy mantle at moderate conditions of pressure and temperature will consist of buoyant ice VI with low concentration of salt, and would likely induce an upwelling current of solutes towards the above liquid ocean. In contrast, a deep and/or thick icy mantle of ice VII will be enriched in salt and hence would form a stable chemical boundary

  19. 2D modeling and simulation of the flow dynamics, electric field and reactions in a low-temperature, atmospheric-pressure nitrogen plasma sharp-end plate-to-plane configuration and CVD reactor

    Science.gov (United States)

    De Wilde, Juray; Lorant, Christophe; Descamps, Pierre

    2017-04-01

    In atmospheric-pressure plasma reactors, the flow dynamics can be complex, determine the reactor performance and complicate scale-up. Coupling computational fluid dynamics to the calculation of the electric field and plasma chemistry is challenging because of the numerical stiffness introduced by the difference in time scale of the different phenomena involved. Focusing on low-temperature, atmospheric-pressure pure nitrogen plasma, a model and model reduction based solution strategy to deal with the numerical stiffness are presented and evaluated. The influence of the electric field on the flow dynamics and species concentration fields is first qualitatively studied by means of 2D simulations of a sharp-end plate-to-plane configuration. Next, a specific reactor prototype for low-temperature, atmospheric-pressure plasma-enhanced chemical vapor deposition for in-line surface treatments is simulated to illustrate the importance of accounting for the detailed flow dynamics.

  20. A thermal-mechanical constitutive model for b-HMX single crystal and cohesive interface under dynamic high pressure loading

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Due to the significant thermal-mechanical effects during hot spot formation in PBX explosives,a thermodynamic constitutive model has been constructed for HMX anisotropic single crystal subjected to dynamic impact loading. The crystal plasticity model based on dislocation dynamics theory was employed to describe the anisotropic plastic behavior along the preferential slip systems. A modified equation of state (EOS) was introduced into the constitutive equations through the decomposing stress tensor and the nonlinear elasticity for materials was taken into account. The one-dimensional strain impact simulations for HMX single crystal and quasi-bicrystal were performed respectively,in which the cohesive elements were inserted over the interface areas for the latter. The predicted particle velocities for the single crystal sample agreed well with the experimental results in the literature. Furthermore,the effects of crystal orientations,interface,misorientations on localized strain,stress and temperature distributions were predicted and discussed.

  1. A dynamic pressure view cell for acoustic stimulation of fluids—Micro-bubble generation and fluid movement in porous media

    Science.gov (United States)

    Stewart, Robert A.; Shaw, J. M.

    2015-09-01

    The development and baseline operation of an acoustic view cell for observing fluids, and fluid-fluid and fluid-solid interfaces in porous media over the frequency range of 10-5000 Hz is described. This range includes the industrially relevant frequency range 500-5000 Hz that is not covered by existing devices. Pressure waveforms of arbitrary shape are generated in a 17.46 mm ID by 200 mm and 690.5 mm long glass tubes at flow rates up to 200 ml/min using a syringe pump. Peak-to-peak amplitudes exceeding 80 kPa are readily realized at frequencies from 10 to 5000 Hz in bubble free fluids when actuated with 20 Vpp as exemplified using castor oil. At resonant frequencies, peak-to-peak pressure amplitudes exceeding 500 kPa were obtained (castor oil at 2100 Hz when actuated with 20 Vpp). Impacts of vibration on macroscopic liquid-liquid and liquid-vapour interfaces and interface movement are illustrated. Pressure wave transmission and attenuation in a fluid saturated porous medium, randomly packed 250-330 μm spherical silica beads, is also demonstrated. Attenuation differences and frequency shifts in resonant peaks are used to detect the presence and generation of dispersed micro-bubbles (visualized. Envisioned applications include assessment of the impacts of vibration on reaction, mass transfer, and flow/flow pattern outcomes. This knowledge will inform laboratory and pilot scale process studies, where nuisance vibrations may affect the interpretation of process outcomes, and large scale or in situ processes in aquifers or hydrocarbon reservoirs where imposed vibration may be deployed to improve aspects of process performance. Future work will include miscible interface observation and quantitative measurements in the bulk and in porous media where the roles of micro-bubbles comprise subjects of special interest.

  2. Pressure-induced phase transitions and structural properties of CoF2: An ab-initio molecular dynamics study

    Science.gov (United States)

    Kürkçü, Cihan; Merdan, Ziya; Öztürk, Hülya

    2016-04-01

    The crystal structure of CoF2 was studied theoretically using first-principles density functional theory (DFT) methods within the generalized gradient approximation (GGA) and local density approximation (LDA) under rapid hydrostatic pressure up to 144 GPa. CoF2 undergoes a structural phase transformation from the rutile-type tetragonal parent phase with space group P42/mnm to the CaCl2-type orthorhombic parent phase with space group Pnnm at 64 GPa with GGA and at 96 GPa with LDA methods. Another phase transformation occurs from the CaCl2-type structure to monoclinic parent phase with space group P21/c at 96 GPa with a GGA method. These phase transitions are also studied by enthalpy and total energy calculations. According to these calculations, we obtained the first phase transformation at about 6.5 GPa both GGA and LDA methods and the later phase transformation at about 45 GPa with the GGA method.

  3. Dynamics

    CERN Document Server

    Goodman, Lawrence E

    2001-01-01

    Beginning text presents complete theoretical treatment of mechanical model systems and deals with technological applications. Topics include introduction to calculus of vectors, particle motion, dynamics of particle systems and plane rigid bodies, technical applications in plane motions, theory of mechanical vibrations, and more. Exercises and answers appear in each chapter.

  4. Dynamical Properties of Hydrogen in ZnO:H Treated by H2/Ar Plasma under Atmospheric Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jun Kue; Kwon, Hyeok-Jung; Kim, Han-Sung; Kim, Dae-Il; Cho, Yong Sub [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    ZnO is a wide-band-gap semiconductor with many technological applications, including catalysis, gas sensing, and the fabrication of microelectronic devices. The geometric, electronic, and defect surface structures play a role in many applications of ZnO. Electron spin resonance (ESR) measurement on temperature was made to identify occupied energy states of H in ZnO:H, the g-value of H being revealed to be 1.96. The dynamical properties of ZnO:H are discussed in view of conversion to hydrogen molecule by analyzing the spin-lattice relaxation time of 1H nuclear magnetic resonance (NMR) spectroscopy. We have investigated the diffusional properties of hydrogen adsorbed on ZnO surface (ZnO:H) by a H{sub 2}/Ar mixed plasma treatment installed at KOMAC. Electron spin resonance measurement identified occupied energy states of H in ZnO:H, the g-value of H being revealed to be 1.96. In further work, the proton dynamics of ZnO:H would be discussed in view of conversion to hydrogen molecule by analyzing the spin-lattice relaxation time of 1H nuclear magnetic resonance spectroscopy.

  5. The Dynamic Calibration Method of High-Pressure Transducer under High-Static Pressure%高压传感器在高静压下的动态校准方法

    Institute of Scientific and Technical Information of China (English)

    张瑜; 裴东兴; 祖静

    2011-01-01

    提出了一种校准高压传感器频响特性的方法,动态校准系统主要由甘油油腔、霍普金森杆、气枪、应变片、电荷放大器、活塞式压力计和数据采集系统等组成.校准时先利用活塞式压力计在封闭式油腔中产生高静压,高静压作用于被校准的压力传感器.气枪发射子弹,子弹撞击霍普金森杆产生近似于冲激函数的窄脉冲应力波,应力波通过甘油传播并激励传感器,数据采集系统同时采集激励信号和传感器的输出信号,最后计算出被校传感器的频响特性.分析了瞬态信号的脉宽与频率校准范围的关系.该校准方法是高压测试系统动态校准的理想方法,实现了高压下压力传感器的动态校准,可校准的下限频率严格地达到零频,为动态高压测试提供有效的计量手段.%A dynamic calibration method of frequency response characteristics of high-pressure sensor is proposed. The calibration system mainly consists of an oil chamber full of glycerin,a Hopkinson bar,an air gun with its fire as sociated apparatuses,a strain gauge,a charge amplifier,a piston gauge and a data acquisition system. In process of the calibration,as a high hydrostatic pressure is applied to the sensor by a piston gauge and a enclosed oil chamber, the air gun-sjioots a bullet to strike Hopkinson bar that a stress wave will be formed. This stress wave is a narrow pulse signal for exciting sensor,I. E. Quasi-8 function. The stress wave propagation through glycerin and excited the sensor. The high precision data acquisition system collected the excited signal and sensor outputs signal and calculated the frequency response of the sensor. The relation between pulse-width of transient signal and calibrating frequency range was analyzed. This calibration method is an ideal method for high pressure sensor,it can realize the low limit frequency of the calibrated frequency range strictly reaches to the frequency of zero Hertz; and it

  6. Dynamic finite element modeling of the effects of size on the upper shelf energy of pressure vessel steels

    Energy Technology Data Exchange (ETDEWEB)

    Sidener, S.E. [Missouri Univ., Rolla, MO (United States); Kumar, A.S. [Missouri Univ., Rolla, MO (United States); Oglesby, D.B. [Missouri Univ., Rolla, MO (United States); Schubert, L.E. [Pacific Northwest Lab., Richland, WA (United States); Hamilton, M.L. [Pacific Northwest Lab., Richland, WA (United States); Rosinski, S.T. [Electric Power Research Inst., Inc. (EPRI), Charlotte, NC (United States)

    1996-12-01

    Dynamic finite element modeling (FEM) of the fracture behavior of fatigue-precracked Charpy specimens was performed to determine the effect of single variable changes in ligament size, width, span, and thickness on the upper shelf energy. A tensile fracture-strain based method for modeling crack initiation and propagation was used. It was found that the upper shelf energy of precracked specimens (USE{sub p}) is proportional to b{sup n}, where b is ligament size and n varies from about 1.6 for subsize to 1.9 for full size specimens. The USE{sub p} was found to be proportional to (width){sup 2.5}. The dependence on span was found to be non-linear. The dependence on thickness was found to be linear for all cases studied. Some of the data from the FEM analysis were compared with experimental data and were found to be in reasonable agreement. (orig.).

  7. Validation of computational fluid dynamics calculation using Rossendorf coolant mixing model flow measurements in primary loop of coolant in a pressurized water reactor model

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, Istvan; Hutli, Ezddin; Faekas, Tatiana; Takacs, Antal; Guba, Attila; Toth, Ivan [Dept. of Thermohydraulics, Centre for Energy Research, Hungarian Academy of Sciences, Budapest (Hungary)

    2016-08-15

    The aim of this work is to simulate the thermohydraulic consequences of a main steam line break and to compare the obtained results with Rossendorf Coolant Mixing Model (ROCOM) 1.1 experimental results. The objective is to utilize data from steady-state mixing experiments and computational fluid dynamics (CFD) calculations to determine the flow distribution and the effect of thermal mixing phenomena in the primary loops for the improvement of normal operation conditions and structural integrity assessment of pressurized water reactors. The numerical model of ROCOM was developed using the FLUENT code. The positions of the inlet and outlet boundary conditions and the distribution of detailed velocity/turbulence parameters were determined by preliminary calculations. The temperature fields of transient calculation were averaged in time and compared with time-averaged experimental data. The perforated barrel under the core inlet homogenizes the flow, and therefore, a uniform temperature distribution is formed in the pressure vessel bottom. The calculated and measured values of lowest temperature were equal. The inlet temperature is an essential parameter for safety assessment. The calculation predicts precisely the experimental results at the core inlet central region. CFD results showed a good agreement (both qualitatively and quantitatively) with experimental results.

  8. Dynamic mechanical behavior and high pressure phase stability of a zirconium-based bulk metallic glass and its composite with tungsten

    Science.gov (United States)

    Martin, Morgana

    2008-10-01

    The research involved performing controlled impact experiments on BMG composites consisting of amorphous Zr57Nb5Cu 15:4Ni12:6Al10 (LM106 or Vitreloy106) with crystalline tungsten reinforcement particles. Monolithic LM106 was also examined to aid in the understanding of the composite. The mechanical behavior of the composite was investigated over a range of strain rates (10-3 s -1 to 106 s-1), stress states (compression, compression-shear, tension), and temperatures (RT to 600°C) to determine the dependence of mechanical properties and deformation and failure modes (i.e., homogeneous deformation vs. inhomogeneous shear banding) on these parameters. Mechanical testing in the quasi-static to intermediate strain-rate regimes was performed using an Instron, Drop Weight Tower, and Split Hopkinson Pressure Bar, respectively. High-strain-rate mechanical properties of the BMG-matrix composite and monolithic BMG were investigated using dynamic compression (reverse Taylor) and dynamic tension (spall) impact experiments performed using a gas gun instrumented with velocity interferometry and high-speed digital photography. These experiments provided information about dynamic strength and deformation modes, and allowed for validation of constitutive models via comparison of experimental and simulated transient deformation profiles and free surface velocity traces. Hugoniot equation of state measurements were performed on the monolithic BMG to investigate the high pressure phase stability of the glass and the possible implications of a high pressure phase transformation on mechanical properties. Specimens were recovered for post-impact microstructural and thermal analysis to gain information about the mechanisms of dynamic deformation and fracture, and to examine for possible shock-induced phase transformations of the amorphous phase. For the composite, mechanical testing revealed positive strain-rate sensitivity of its yield stress and negative strain-rate sensitivity of its

  9. Molecular dynamics simulation of the thermodynamic properties of mercury at pressures below 2.5 GPa and temperatures below 10000 K

    Science.gov (United States)

    Belashchenko, D. K.

    2017-08-01

    Models of mercury were constructed by molecular dynamics using the interparticle potential of the embedded atom model (EAM) at temperatures below 10 000 K and pressures below 2.5 GPa. The thermodynamic properties of the models were presented on the isobars of 0.5, 1.0, 1.5, 2.0, and 2.5 GPa. The compressibility factors Z = pV/( RT) were calculated; the coordinates of the inversion points of the Joule-Thomson coefficient below 5600 K were found from the positions of minima on the Z( p, T) isobars. At densities above 8-9 g/cm3, the results of simulation agreed well with experiment; at lower densities there were discrepancies associated with a loss of metal properties by real mercury. The behavior of the models was analyzed in the region of the van der Waals loop. The calculated critical temperature of mercury was found to be significantly overestimated relative to the experiment. Modeling the "meta-mercury" with the EAM potential with excluded embedded potential contribution gave better agreement with the equation of state of mercury at lower densities. The states with Z = 1 can be observed below 1.0 GPa. The calculated temperature of the inversion of the Joule-Thomson coefficient increased monotonically to 5600 K as the pressure increased to 2.5 GPa.

  10. Max Launch Abort System (MLAS) Pad Abort Test Vehicle (PATV) II Attitude Control System (ACS) Integration and Pressurization Subsystem Dynamic Random Vibration Analysis

    Science.gov (United States)

    Ekrami, Yasamin; Cook, Joseph S.

    2011-01-01

    In order to mitigate catastrophic failures on future generation space vehicles, engineers at the National Aeronautics and Space Administration have begun to integrate a novel crew abort systems that could pull a crew module away in case of an emergency at the launch pad or during ascent. The Max Launch Abort System (MLAS) is a recent test vehicle that was designed as an alternative to the baseline Orion Launch Abort System (LAS) to demonstrate the performance of a "tower-less" LAS configuration under abort conditions. The MLAS II test vehicle will execute a propulsive coast stabilization maneuver during abort to control the vehicles trajectory and thrust. To accomplish this, the spacecraft will integrate an Attitude Control System (ACS) with eight hypergolic monomethyl hydrazine liquid propulsion engines that are capable of operating in a quick pulsing mode. Two main elements of the ACS include a propellant distribution subsystem and a pressurization subsystem to regulate the flow of pressurized gas to the propellant tanks and the engines. The CAD assembly of the Attitude Control System (ACS) was configured and integrated into the Launch Abort Vehicle (LAV) design. A dynamic random vibration analysis was conducted on the Main Propulsion System (MPS) helium pressurization panels to assess the response of the panel and its components under increased gravitational acceleration loads during flight. The results indicated that the panels fundamental and natural frequencies were farther from the maximum Acceleration Spectral Density (ASD) vibrations which were in the range of 150-300 Hz. These values will direct how the components will be packaged in the vehicle to reduce the effects high gravitational loads.

  11. Dynamic changes in optic disc morphology, choroidal thickness, anterior chamber parameters, and intraocular pressure during Valsalva maneuver

    Directory of Open Access Journals (Sweden)

    Alper Mete

    Full Text Available ABSTRACT Purpose: To investigate the effects of the Valsalva maneuver (VM on optic disc morphology, choroidal thickness, and anterior chamber parameters. Methods: This prospective observational study included 60 eyes of 60 healthy subjects. The anterior chamber parameters, including central corneal thickness (CCT, anterior chamber depth (ACD, anterior chamber angle (ACA, anterior chamber volume (ACV, pupil diameter (PD, axial length (AL, subfoveal and peripapillary choroidal thickness, optic disc parameters, and intraocular pressure (IOP, were measured at rest and during VM. Results: VM did not have any significant influence on AL, subfoveal and peripapillary choroidal thickness, optic disc area, rim area, cup area, cup-to-disc area ratio, vertical cup-to-disc ratio, rim volume, cup volume, and nerve head volume measurements (for all; p >0.05. IOP and PD significantly increased during VM (for both; p <0.001. VM significantly decreased CCT, ACD, ACA, and ACV values (for all; p <0.001. Moreover, the optic nerve cup volume decreased and the horizontal cup-to-disc ratio significantly increased during VM (for both; p <0.05. Conclusions: VM may cause transient changes in IOP, optic disc morphology, and anterior chamber parameters.

  12. Dynamic modeling of uteroplacental blood flow in IUGR indicates vortices and elevated pressure in the intervillous space - a pilot study.

    Science.gov (United States)

    Roth, Christian J; Haeussner, Eva; Ruebelmann, Tanja; Koch, Franz V; Schmitz, Christoph; Frank, Hans-Georg; Wall, Wolfgang A

    2017-01-19

    Ischemic placental disease is a concept that links intrauterine growth retardation (IUGR) and preeclampsia (PE) back to insufficient remodeling of uterine spiral arteries. The rheological consequences of insufficient remodeling of uterine spiral arteries were hypothesized to mediate the considerably later manifestation of obstetric disease. However, the micro-rheology in the intervillous space (IVS) cannot be examined clinically and rheological animal models of the human IVS do not exist. Thus, an in silico approach was implemented to provide in vivo inaccessible data. The morphology of a spiral artery and the inflow region of the IVS were three-dimensionally reconstructed to provide a morphological stage for the simulations. Advanced high-end supercomputing resources were used to provide blood flow simulations at high spatial resolution. Our simulations revealed turbulent blood flow (high-velocity jets and vortices) combined with elevated blood pressure in the IVS and increased wall shear stress at the villous surface in conjunction with insufficient spiral artery remodeling only. Post-hoc histological analysis of uterine veins showed evidence of increased trophoblast shedding in an IUGR placenta. Our data support that rheological alteration in the IVS is a relevant mechanism linking ischemic placental disease to altered structural integrity and function of the placenta.

  13. Dynamics of Dusty Radiation Pressure Driven Shells: Fast Outflows from Galaxies, Star Clusters, Massive Stars, and AGN

    CERN Document Server

    Thompson, Todd A; Quataert, Eliot; Murray, Norman

    2014-01-01

    It is typically assumed that radiation pressure driven winds are accelerated to an asymptotic velocity of v_inf ~ v_esc, where v_esc is the escape velocity from the central source. We note that this is not the case for dusty shells. Instead, if the shell is initially optically-thick to the UV emission from the source of luminosity L, then there is a significant boost in v_inf that reflects the integral of the momentum absorbed by the shell as it is accelerated. For shells reaching a generalized Eddington limit, we show that v_inf ~ (4 R_UV L / M_sh c)^{1/2}, in both point-mass and isothermal-sphere potentials, where R_UV is the radius where the shell becomes optically-thin to UV photons, and M_sh is the mass of the shell. The asymptotic velocity significantly exceeds v_esc for typical parameters, and can explain the ~1000-2000 km/s outflows observed from rapidly star-forming galaxies and active galactic nuclei if their geometry is shell-like and if the surrounding halo has low gas density. Similarly fast shel...

  14. Effective population size dynamics reveal impacts of historic climatic events and recent anthropogenic pressure in African elephants.

    Science.gov (United States)

    Okello, J B A; Wittemyer, G; Rasmussen, H B; Arctander, P; Nyakaana, S; Douglas-Hamilton, I; Siegismund, H R

    2008-09-01

    Two hundred years of elephant hunting for ivory, peaking in 1970-1980s, caused local extirpations and massive population declines across Africa. The resulting genetic impacts on surviving populations have not been studied, despite the importance of understanding the evolutionary repercussions of such human-mediated events on this keystone species. Using Bayesian coalescent-based genetic methods to evaluate time-specific changes in effective population size, we analysed genetic variation in 20 highly polymorphic microsatellite loci from 400 elephants inhabiting the greater Samburu-Laikipia region of northern Kenya. This area experienced a decline of between 80% and 90% in the last few decades when ivory harvesting was rampant. The most significant change in effective population size, however, occurred approximately 2500 years ago during a mid-Holocene period of climatic drying in tropical Africa. Contrary to expectations, detailed analyses of four contemporary age-based cohorts showed that the peak poaching epidemic in the 1970s caused detectable temporary genetic impacts, with genetic diversity rebounding as juveniles surviving the poaching era became reproductively mature. This study demonstrates the importance of climatic history in shaping the distribution and genetic history of a keystone species and highlights the utility of coalescent-based demographic approaches in unravelling ancestral demographic events despite a lack of ancient samples. Unique insights into the genetic signature of mid-Holocene climatic change in Africa and effects of recent poaching pressure on elephants are discussed.

  15. Effects of high hydrostatic pressure on distribution dynamics of free amino acids in water soaked brown rice grain

    Energy Technology Data Exchange (ETDEWEB)

    Shigematsu, T; Nakajima, K; Uno, Y; Sakano, A; Murakami, M; Narahara, Y; Fujii, T [Department of Food Sci., Niigata University Pharm. Appl. Life Sci. (NUPALS), Niigata, Niigata, 956-8603 (Japan); Hayashi, M [Niigata Industrial Creation Organization (NICO), Niigata, Niigata, 950-0078 (Japan); Ueno, S, E-mail: shige@nupals.ac.j [Grad. School of Agric. Sci., Tohoku University, Sendai, Miyagi, 981-8555 (Japan)

    2010-03-01

    High hydrostatic pressure (HP) with approximately below 400 MPa can induce a transformation of food materials to an alternative form, where membrane systems are damaged but certain enzymes are still active. HP treatment of water soaked brown rice grain could modify the mass transfer inside and apparent activities of enzymes, resulting in HP-dependent change of distribution of free amino acids. Thus, the distribution of free amino acids in brown rice grain during preservation after HP treatment was analyzed. Just after HP treatment at 200 MPa for 10 min, the distribution of free amino acids was not apparently different from that of untreated control. In contrast, after 1 to 4 days preservation at 25{sup 0}C, amino acids, such as Ala, Glu, Gly, Asp and Val, showed higher concentrations than those in control. This result suggested that HP treatment induced proteolysis to produce free amino acids. However, Gln, Thr and Cys, showed no apparent difference, suggesting that conversion of certain amino acids produced by proteolysis occurred. Moreover, the concentration of {gamma}-aminobutyric acid (GABA) in HP-treated sample was higher than that in untreated control. These results suggested that HP treatment induced alteration of distribution of free amino acids of rice grains via proteolysis and certain amino acids metabolism pathways.

  16. Human cells derived from degenerate intervertebral discs respond differently to those derived from non-degenerate intervertebral discs following application of dynamic hydrostatic pressure.

    Science.gov (United States)

    Le Maitre, Christine Lyn; Frain, Jennie; Fotheringham, Andrew P; F