WorldWideScience

Sample records for dynamic material properties

  1. Dynamic properties of ceramic materials

    Energy Technology Data Exchange (ETDEWEB)

    Grady, D.E. [Sandia National Labs., Albuquerque, NM (United States). Experimental Impact Physics Dept.

    1995-02-01

    The present study offers new data and analysis on the transient shock strength and equation-of-state properties of ceramics. Various dynamic data on nine high strength ceramics are provided with wave profile measurements, through velocity interferometry techniques, the principal observable. Compressive failure in the shock wave front, with emphasis on brittle versus ductile mechanisms of deformation, is examined in some detail. Extensive spall strength data are provided and related to the theoretical spall strength, and to energy-based theories of the spall process. Failure waves, as a mechanism of deformation in the transient shock process, are examined. Strength and equation-of-state analysis of shock data on silicon carbide, boron carbide, tungsten carbide, silicon dioxide and aluminum nitride is presented with particular emphasis on phase transition properties for the latter two. Wave profile measurements on selected ceramics are investigated for evidence of rate sensitive elastic precursor decay in the shock front failure process.

  2. Material properties under intensive dynamic loading

    CERN Document Server

    Cherne, Frank J; Zhernokletov, Mikhail V; Glushak, B L; Zocher, Marvin A

    2007-01-01

    Understanding the physical and thermomechanical response of materials subjected to intensive dynamic loading is a challenge of great significance in engineering today. This volume assumes the task of gathering both experimental and diagnostic methods in one place, since not much information has been previously disseminated in the scientific literature.

  3. Frequency-dependent dynamic effective properties of porous materials

    Institute of Scientific and Technical Information of China (English)

    Peijun Wei; Zhuping Huang

    2005-01-01

    The frequency-dependent dynamic effective properties (phase velocity, attenuation and elastic modulus) of porous materials are studied numerically. The coherent plane longitudinal and shear wave equations, which are obtained by averaging on the multiple scattering fields, are used to evaluate the frequency-dependent dynamic effective properties of a porous material. It is found that the prediction of the dynamic effective properties includes the size effects of voids which are not included in most prediction of the traditional static effective properties. The prediction of the dynamic effective elastic modulus at a relatively low frequency range is compared with that of the traditional static effective elastic modulus, and the dynamic effective elastic modulus is found to be very close to the Hashin-Shtrikman upper bound.

  4. Dynamic Deformation Properties of Energetic Composite Materials

    Science.gov (United States)

    2005-04-01

    properties are close to that of pure beryllium ( Silversmith and Averbach 1970), but as far as we know no-one has acted on this suggestion. According to...J.L. (1998) "Analysis of load oscillations in instrumented impact testing" Engng Fract. Mech. 60 437-446 Silversmith , D.J. and Averbach, B.L. (1970

  5. Dynamic material properties of the pregnant human uterus.

    Science.gov (United States)

    Manoogian, Sarah J; Bisplinghoff, Jill A; Kemper, Andrew R; Duma, Stefan M

    2012-06-01

    Given that automobile crashes are the largest single cause of death for pregnant females, scientists are developing advanced computer models of pregnant occupants. The purpose of this study is to quantify the dynamic material properties of the human uterus in order to increase the biofidelity of these models. A total of 19 dynamic tension tests were performed on pregnant human uterus tissues taken from six separate donors. The tissues were collected during full term Cesarean style deliveries and tested within 36 h of surgery. The tissues were processed into uniform coupon sections and tested at 1.5 strains/s using linear motors. Local stress and strain were determined from load data and optical markers using high speed video. The experiments resulted in a non-linear stress versus strain curves with an overall average peak failure true strain of 0.32±0.112 and a corresponding peak failure true stress of 656.3±483.9 kPa. These are the first data available for the dynamic response of pregnant human uterus tissues, and it is anticipated they will increase the accuracy of future pregnant female computational models.

  6. Spin Dynamics simulations of the dynamic properties of classical models for magnetic materials

    Science.gov (United States)

    Bunker, Alex; Landau, D. P.

    1998-03-01

    The Spin Dynamics simulation technique, which has had considerable success for the study of critical properties of classical Heisenberg antiferromagnets(A. Bunker, K. Chen, and D. P. Landau Phys. Rev. B) \\underline54, 9259 (1996), has been used to determine more general properties for a wider range of materials. A general spin dynamics program has been developed which can determine the dynamic structure factor, S(q,ω), in the [100], [110], and [111] directions for a wide range of classical magnetic models at any temperature desired. We have simulated the magnetic dynamics in the ordered phase of the isotropic Heisenberg model with both ferromagnetic and antiferromagnetic coupling on L×L×L BCC and SC lattices. Outside of the critical regime relatively small lattice sizes of L = 12, 24 could be used. From our simulation we have determined the stiffness coefficient and the spin relaxation rate which were compared to both experimental(J. Als-Nielsen in Phase Transitions and Critical Phenomena), ed. C. Domb, M. S. Green, Academic Press, (1976) and theoretical results. We have performed the same simulation with anisotropy appropriate for MnF2 and FeF_2. Research supported in part by the NSF

  7. STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL

    OpenAIRE

    Adhiyamaan Arivazhagan; Ammar Saleem; S. H. Masood; Mostafa Nikzad; K. A. JAGADEESH

    2014-01-01

    Fused Deposition Modelling (FDM), a renowned Rapid Prototyping (RP) process, has been successfully implemented in several industries to fabricate concept models and prototypes for rapid manufacturing. This study furnishes terse notes about the material damping properties of FDM made ULTEM samples considering the effect of FDM process parameters. Dynamic Mechanical Analysis (DMA) is carried out using DMA 2980 equipment to study the dynamic response of the FDM material subjected to single canti...

  8. Experimental investigation on the dynamic mechanical properties of soft magnetic entangled metallic wire material

    Science.gov (United States)

    Ma, Yanhong; Zhang, Qicheng; Zhang, Dayi; Hu, Wenzhong; Hong, Jie

    2017-05-01

    This work describes the dynamic characteristics of a novel soft magnetic entangled metallic wire material(SM-EMWM) by the dynamic tests for the first time. The mechanical properties of three batches of SM-EMWMs with different porosities have been investigated under different dynamic loads in different magnetic field intensities. The result shows that its properties (storage modulus and loss factor) have commendably controllable magnetic responses in the magnetic field. In particular, the dynamic damping is more remarkable than its quasi-static performance, and the loss factor can be improved above 50% in the magnetic field of 500 mT. The results indicate that SM-EMWM as a magneto-sensitive smart material possesses a considerable application prospect for the active vibration control with variable stiffness and damping.

  9. Microstructure and Dynamic Failure Properties of Freeze-Cast Materials for Thermobaric Warhead Cases

    Science.gov (United States)

    2012-12-01

    LIST OF FIGURES Figure 1. Freeze cast process: slurry preparation, solidification, sublimation and sintering (From Ref 6...the process can be divided into four steps, illustrated in Figure 1. 6 Figure 1. Freeze cast process: slurry preparation, solidification...DYNAMIC FAILURE PROPERTIES OF FREEZE- CAST MATERIALS FOR THERMOBARIC WARHEAD CASES by Yi Ming Tan December 2012 Thesis Advisor: Joseph

  10. Dynamical properties measurements for asteroid, comet and meteorite material applicable to impact modeling and mitigation calculations

    Energy Technology Data Exchange (ETDEWEB)

    Furnish, M.D.; Boslough, M.B. [Sandia National Labs., Albuquerque, NM (United States); Gray, G.T. III [Los Alamos National Lab., NM (United States); Remo, J.L. [Quantametrics, Inc., St. James, NY (United States)

    1994-07-01

    We describe methods for measuring dynamical properties for two material categories of interest in understanding large-scale extraterrestrial impacts: iron-nickel and underdense materials (e.g. snow). Particular material properties measured by the present methods include Hugoniot release paths and constitutive properties (stress vs. strain). The iron-nickel materials lend themselves well to conventional shock and quasi-static experiments. As examples, a suite of experiments is described including six impact tests (wave profile compression/release) over the stress range 2--20 GPa, metallography, quasi-static and split Hopkinson pressure bar (SHPB) mechanical testing, and ultrasonic mapping and sound velocity measurements. Temperature sensitivity of the dynamic behavior was measured at high and low strain rates. Among the iron-nickel materials tested, an octahedrite was found to have behavior close to that of Armco iron under shock and quasi-static conditions, while an ataxite exhibited a significantly larger quasi-static yield strength than did the octahedrite or a hexahedrite. The underdense materials pose three primary experimental difficulties. First, the samples are friable; they can melt or sublimate during storage, preparation and testing. Second, they are brittle and crushable; they cannot withstand such treatment as traditional machining or launch in a gun system. Third, with increasing porosity the calculated Hugoniot density becomes rapidly more sensitive to errors in wave time-of-arrival measurements. Carefully chosen simulants eliminate preservation (friability) difficulties, but the other difficulties remain. A family of 36 impact tests was conducted on snow and snow simulants at Sandia, yielding reliable Hugoniot and reshock states, but limited release property information. Other methods for characterizing these materials are discussed.

  11. Dynamical properties measurements for asteroid, comet and meteorite material applicable to impact modeling and mitigation calculations

    Science.gov (United States)

    Furnish, M. D.; Boslough, M. B.; Gray, G. T., III; Remo, J. L.

    We describe methods for measuring dynamical properties for two material categories of interest in understanding large-scale extraterrestrial impacts: iron-nickel and underdense materials (e.g. snow). Particular material properties measured by the present methods include Hugoniot release paths and constitutive properties (stress vs. strain). The iron-nickel materials lend themselves well to conventional shock and quasi-static experiments. As examples, a suite of experiments is described including six impact tests (wave profile compression/release) over the stress range 2-20 GPa, metallography, quasi-static and split Hopkinson pressure bar (SHPB) mechanical testing, and ultrasonic mapping and sound velocity measurements. Temperature sensitivity of the dynamic behavior was measured at high and low strain rates. Among the iron-nickel materials tested, an octahedrite was found to have behavior close to that of Armco iron under shock and quasi-static conditions, while an ataxite exhibited a significantly larger quasi-static yield strength than did the octahedrite or a hexahedrite. The underdense materials pose three primary experimental difficulties. First, the samples are friable; they can melt or sublimate during storage, preparation and testing. Second, they are brittle and crushable; they cannot withstand such treatment as traditional machining or launch in a gun system. Third, with increasing porosity the calculated Hugoniot density becomes rapidly more sensitive to errors in wave time-of-arrival measurements. Carefully chosen simulants eliminate preservation (friability) difficulties, but the other difficulties remain. A family of 36 impact tests was conducted on snow and snow simulants at Sandia, yielding reliable Hugoniot and reshock states, but limited release property information. Other methods for characterizing these materials are discussed.

  12. STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL

    Directory of Open Access Journals (Sweden)

    Adhiyamaan Arivazhagan

    2014-01-01

    Full Text Available Fused Deposition Modelling (FDM, a renowned Rapid Prototyping (RP process, has been successfully implemented in several industries to fabricate concept models and prototypes for rapid manufacturing. This study furnishes terse notes about the material damping properties of FDM made ULTEM samples considering the effect of FDM process parameters. Dynamic Mechanical Analysis (DMA is carried out using DMA 2980 equipment to study the dynamic response of the FDM material subjected to single cantilever loading under periodic stress. Three FDM process parameters namely Build Style, Raster Width and Raster Angle were contemplated. ULTEM parts are fabricated using solid normal build style and three values each of raster width and raster angle. DMA is performed with temperature sweep at three different fixed frequencies of 1, 50 and 100 Hz. Results were obtained for dynamic properties such as Maximum Storage Modulus, Maximum Loss Modulus, Maximum Tan Delta and Maximum Complex Viscosity. The present work discusses the effect of increasing the frequencies and temperature on FDM made ULTEM samples using different FDM process parameters.

  13. Uncertain dynamic analysis for rigid-flexible mechanisms with random geometry and material properties

    Science.gov (United States)

    Wu, Jinglai; Luo, Zhen; Zhang, Nong; Zhang, Yunqing; Walker, Paul D.

    2017-02-01

    This paper proposes an uncertain modelling and computational method to analyze dynamic responses of rigid-flexible multibody systems (or mechanisms) with random geometry and material properties. Firstly, the deterministic model for the rigid-flexible multibody system is built with the absolute node coordinate formula (ANCF), in which the flexible parts are modeled by using ANCF elements, while the rigid parts are described by ANCF reference nodes (ANCF-RNs). Secondly, uncertainty for the geometry of rigid parts is expressed as uniform random variables, while the uncertainty for the material properties of flexible parts is modeled as a continuous random field, which is further discretized to Gaussian random variables using a series expansion method. Finally, a non-intrusive numerical method is developed to solve the dynamic equations of systems involving both types of random variables, which systematically integrates the deterministic generalized-α solver with Latin Hypercube sampling (LHS) and Polynomial Chaos (PC) expansion. The benchmark slider-crank mechanism is used as a numerical example to demonstrate the characteristics of the proposed method.

  14. Dynamic Material Property Measurement of Steel Thin Sheets using Laser-Based Ultrasonics

    Science.gov (United States)

    Nagata, Y.; Yamada, H.; Hashiguchi, S.; Lim, C. S.; Park, H. C.; Huh, H. J.; Kang, M. K.; Oh, K. J.

    2014-06-01

    A material property measurement system for steel sheets using laser-based ultrasonics was developed. The system consists of a pulsed Nd:YAG laser for ultrasonic generation and multi-channel interferometer coupled with a CW single frequency laser for ultrasonic detection. The system can measure the frequency of the S1 Lamb wave mode of zero group velocity (S1f) as well as the longitudinal resonance frequencies without ablative damage to the steel surface. It was confirmed that Poisson's ratio could be directly obtained by combining the measured S1f value and the longitudinal resonance frequencies. To evaluate the applicability of this system in an actual steel production setting, the system was installed in hot rolling pilot plant that produces steel samples. As a result, it was demonstrated that the system can measure dynamic changes in Poisson's ratio values within steel sheets, even in the hot rolling pilot plant environment. Material property data, such as Poisson's ratio, during the thin sheet production process will be very useful for manufacturing high value-added steel, such as sheets with uniform quality.

  15. Two-component membrane material properties and domain formation from dissipative particle dynamics.

    Science.gov (United States)

    Illya, G; Lipowsky, R; Shillcock, J C

    2006-09-21

    The material parameters (area stretch modulus and bending rigidity) of two-component amphiphilic membranes are determined from dissipative particle dynamics simulations. The preferred area per molecule for each species is varied so as to produce homogeneous mixtures or nonhomogeneous mixtures that form domains. If the latter mixtures are composed of amphiphiles with the same tail length, but different preferred areas per molecule, their material parameters increase monotonically as a function of composition. By contrast, mixtures of amphiphiles that differ in both tail length and preferred area per molecule form both homogeneous and nonhomogeneous mixtures that both exhibit smaller values of their material properties compared to the corresponding pure systems. When the same nonhomogeneous mixtures of amphiphiles are assembled into planar membrane patches and vesicles, the resulting domain shapes are different when the bending rigidities of the domains are sufficiently different. Additionally, both bilayer and monolayer domains are observed in vesicles. We conclude that the evolution of the domain shapes is influenced by the high curvature of the vesicles in the simulation, a result that may be relevant for biological vesicle membranes.

  16. Material property evaluations of bimetallic welds, stainless steel saw fusion lines, and materials affected by dynamic strain aging

    Energy Technology Data Exchange (ETDEWEB)

    Rudland, D.; Scott, P.; Marschall, C.; Wilkowski, G. [Battelle Memorial Institute, Columbus, OH (United States)

    1997-04-01

    Pipe fracture analyses can often reasonably predict the behavior of flawed piping. However, there are material applications with uncertainties in fracture behavior. This paper summarizes work on three such cases. First, the fracture behavior of bimetallic welds are discussed. The purpose of the study was to determine if current fracture analyses can predict the response of pipe with flaws in bimetallic welds. The weld joined sections of A516 Grade 70 carbon steel to F316 stainless steel. The crack was along the carbon steel base metal to Inconel 182 weld metal fusion line. Material properties from tensile and C(T) specimens were used to predict large pipe response. The major conclusion from the work is that fracture behavior of the weld could be evaluated with reasonable accuracy using properties of the carbon steel pipe and conventional J-estimation analyses. However, results may not be generally true for all bimetallic welds. Second, the toughness of austenitic steel submerged-arc weld (SAW) fusion lines is discussed. During large-scale pipe tests with flaws in the center of the SAW, the crack tended to grow into the fusion line. The fracture toughness of the base metal, the SAW, and the fusion line were determined and compared. The major conclusion reached is that although the fusion line had a higher initiation toughness than the weld metal, the fusion-line J-R curve reached a steady-state value while the SAW J-R curve increased. Last, carbon steel fracture experiments containing circumferential flaws with periods of unstable crack jumps during steady ductile tearing are discussed. These instabilities are believed to be due to dynamic strain aging (DSA). The paper discusses DSA, a screening criteria developed to predict DSA, and the ability of the current J-based methodologies to assess the effect of these crack instabilities. The effect of loading rate on the strength and toughness of several different carbon steel pipes at LWR temperatures is also discussed.

  17. Determination of the viscoelastic properties of elastomeric materials by the dynamic indentation method

    NARCIS (Netherlands)

    Vriend, Nathalie M.; Kren, Alexander P.

    2004-01-01

    In this paper the dynamic indentation test method, which is not often used, is discussed. The goal of the paper is to consider the possibility of applying a dynamic indentation test method to investigate rubber materials. The basic equations for the determination of the viscoelastic characteristics

  18. Simulation of material properties below the Debye temperature: A path-integral molecular dynamics case study of quartz

    Science.gov (United States)

    Müser, Martin H.

    2001-04-01

    Classical and path integral molecular dynamics (PIMD) simulations are used to study α and β quartz in a large range of temperatures at zero external stress. PIMD account for quantum fluctuations of atomic vibrations, which can modify material properties at temperatures below the Debye temperature. The difference between classical and quantum mechanical results for bond lengths, bond angles, elastic moduli, and some dynamical properties is calculated and comparison to experimental data is done. Only quantum mechanical simulations are able to reproduce the correct thermomechanical properties below room temperature. It is discussed in how far classical and PIMD simulations can be helpful in constructing improved potential energy surfaces for silica.

  19. Effect of carbonation on the linear and nonlinear dynamic properties of cement-based materials

    Science.gov (United States)

    Eiras, Jesus N.; Kundu, Tribikram; Popovics, John S.; Monzó, José; Borrachero, María V.; Payá, Jordi

    2016-01-01

    Carbonation causes a physicochemical alteration of cement-based materials, leading to a decrease of porosity and an increase of material hardness and strength. However, carbonation will decrease the pH of the internal pore water solution, which may depassivate the internal reinforcing steel, giving rise to structural durability concerns. Therefore, the proper selection of materials informed by parameters sensitive to the carbonation process is crucial to ensure the durability of concrete structures. The authors investigate the feasibility of using linear and nonlinear dynamic vibration response data to monitor the progression of the carbonation process in cement-based materials. Mortar samples with dimensions of 40×40×160 mm were subjected to an accelerated carbonation process through a carbonation chamber with 55% relative humidity and >95% of CO2 atmosphere. The progress of carbonation in the material was monitored using data obtained with the test setup of the standard resonant frequency test (ASTM C215-14), from a pristine state until an almost fully carbonated state. Linear dynamic modulus, quality factor, and a material nonlinear response, evaluated through the upward resonant frequency shift during the signal ring-down, were investigated. The compressive strength and the depth of carbonation were also measured. Carbonation resulted in a modest increase in the dynamic modulus, but a substantive increase in the quality factor (inverse attenuation) and a decrease in the material nonlinearity parameter. The combined measurement of the vibration quality factor and nonlinear parameter shows potential as a sensitive measure of material changes brought about by carbonation.

  20. Synthesis, structure and properties of hierarchical nanostructured porous materials studied by molecular dynamics simulations

    Science.gov (United States)

    Chae, Kisung

    For applications of porous materials in many fields of technological importance, such as catalysis, filtration, separation, energy storage and conversion, the efficiency is often limited by chemical kinetics, and/or diffusion of reactants and products to and from the active sites. Hierarchical nanostructured porous materials (HNPMs) that possess both mesopores (2 nm size size size and the pore wall roughness as well as the microporous structure such as the density and the graphitic pore walls can be independently controlled by synthesis parameters, such as the size of the template, the interaction strength between the template and carbon source, the initial carbon density and the quench rate, respectively. These atomic models allowed us to quantify the structure-mechanical properties relation in aligned carbon nanotubes/amorphous porous carbon nanocomposites. Our study shows that there is an optimum balance between the crystallinity of CNTs and the number bridging bonds between CNTs and the microporous matrix in order for the nanocomposites to have desired mechanical properties such as high stiffness and high buckling resistance under compressive loading. We further used these models to study the effects of the mesopore size and the pore wall roughness on the transport behaviors of methane in HNPCs. Our study shows that some defects in the mesopore walls do not have a significant effect on transport properties, especially in large channels. However, when the walls of small channels become rough, adsorption and transport behaviors change dramatically. Our study shows that the enhanced flow in CNTs observed in experiments is mainly due to the smooth potential energy surface of CNTs with high quality of graphitic walls. In order to carry out a systematic study on pressure-driven gas transport in HNPCs, a computationally efficient reflecting particle method (RPM) together with a perturbation-relaxation loop was developed in this work to make the pressure drop

  1. Dynamic Diamond Anvil Cell (dDAC): A novel device for studying the dynamic-pressure properties of materials

    Energy Technology Data Exchange (ETDEWEB)

    Evans, W J; Yoo, C; Lee, G W; Cynn, H; Lipp, M J; Visbeck, K

    2007-02-23

    We have developed a unique device, a dynamic diamond anvil cell (dDAC), which repetitively applies a time-dependent load/pressure profile to a sample. This capability allows studies of the kinetics of phase transitions and metastable phases at compression (strain) rates of up to 500 GPa/sec ({approx}0.16 s{sup -1} for a metal). Our approach adapts electromechanical piezoelectric actuators to a conventional diamond anvil cell design, which enables precise specification and control of a time-dependent applied load/pressure. Existing DAC instrumentation and experimental techniques are easily adapted to the dDAC to measure the properties of a sample under the varying load/pressure conditions. This capability addresses the sparsely studied regime of dynamic phenomena between static research (diamond anvil cells and large volume presses) and dynamic shock-driven experiments (gas guns, explosive and laser shock). We present an overview of a variety of experimental measurements that can be made with this device.

  2. The biomechanics of human ribs: material and structural properties from dynamic tension and bending tests.

    Science.gov (United States)

    Kemper, Andrew R; McNally, Craig; Pullins, Clayton A; Freeman, Laura J; Duma, Stefan M; Rouhana, Stephen M

    2007-10-01

    The purpose of this study was to quantify both the tensile material properties and structural response of human ribs in order to determine which variables contribute to regional variation in the strength of human ribs. This was done by performing 94 matched tests on human rib specimens; 46 tension coupon tests, 48 three-point bending tests. Contralateral matched specimens were dissected from anterior and lateral regions of ribs 4 through 7 of six male fresh frozen post mortem human subjects ranging from 42 to 81 years of age. Tension coupons were taken from one side of the thorax, while three-point bending specimens were taken from the opposite side as the tension coupons at corresponding anatomical locations. The results of the tension coupon testing showed that there were no significant differences with respect to region or rib level: ultimate stress (p=0.90; p=0.53), ultimate strain (p=0.49; p=0.86), or modulus (p=0.72; p=0.81). In contrast, lateral three-point bending specimens were found to have a significantly higher peak bending moment (pbending specimens also had a significantly larger area moment of inertia (pradius of gyration (pradius of gyration (p=0.04) were found to be significantly different with respect to rib level. For lateral specimens, the area moment of inertia (pradius of gyration (p=0.03) were found to be significantly different with respect to rib level. These results clearly illustrate that there is variation in the structural response of human ribs with respect to anatomical region and rib level and this variation is due to changes in local geometry of each rib while the material properties remain constant.

  3. Static and Dynamical Properties of Ferroelectrics and Related Materials in Bulk and Nanostructure Forms

    Science.gov (United States)

    Gui, Zhigang

    Ferroelectrics (FE) and multiferroics (MFE) have attracted a lot of attentions due to their rich and novel properties. Studies towards FE and MFE are of both fundamental and technological importance. We use a first-principles-based effective Hamiltonian method, conventional ab-initio packages and linear-scale three-dimension fragment method to investigate several important issues about FE and MFE. Tuning the properties of FE and MFE films are essential for miniaturized device applications, which can be realized through epitaxial strain and growth direction. In this dissertation, we use the effective Hamiltonian method to study (i) BaTiO3 films grown along the (110) pseudocubic direction on various substrates, (ii) BaTiO3 films grown on a single substrate along directions varying from [001] to [110] via [111] pseudocubic direction. Optimized physical responses or curie temperatures are found along some special directions or under epitaxial strain of certain range. FE and MFE nanostructures are shown to possess electrical vortices (known as one type topological defect), which have the potential to be used in new memory devices. However, the dynamic mechanism behind them is barely known. We use the effective Hamiltonian method to reveal that there exists a distinct mode which is shown to be responsible for the formation of the electrical vortices and in the THz region. Spin-canted magnetic structures are commonly seen in MFE, which results in the coexistence of two or more magnetic order parameters in the same structure. Understanding the physics behind such coupled magnetic order parameters is of obvious benefit for the sake of control of the magnetic properties of such systems. We employ both the effective Hamiltonian and ab-initio methods to derive and prove there is a universal law that explicitly correlates various magnetic order parameters with the different types of oxygen octahedra rotations. FE or MFE possessing electrical vortices are experimentally shown to

  4. Chemically specific multiscale modeling of clay-polymer nanocomposites reveals intercalation dynamics, tactoid self-assembly and emergent materials properties.

    Science.gov (United States)

    Suter, James L; Groen, Derek; Coveney, Peter V

    2015-02-01

    A quantitative description is presented of the dynamical process of polymer intercalation into clay tactoids and the ensuing aggregation of polymer-entangled tactoids into larger structures, obtaining various characteristics of these nanocomposites, including clay-layer spacings, out-of-plane clay-sheet bending energies, X-ray diffractograms, and materials properties. This model of clay-polymer interactions is based on a three-level approach, which uses quantum mechanical and atomistic descriptions to derive a coarse-grained yet chemically specific representation that can resolve processes on hitherto inaccessible length and time scales. The approach is applied to study collections of clay mineral tactoids interacting with two synthetic polymers, poly(ethylene glycol) and poly(vinyl alcohol). The controlled behavior of layered materials in a polymer matrix is centrally important for many engineering and manufacturing applications. This approach opens up a route to computing the properties of complex soft materials based on knowledge of their chemical composition, molecular structure, and processing conditions. © 2014 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Dynamic Material Properties of Orthotropic Polymer and Molybdenum for Use in Next Generation Composite Armor Concept?

    Science.gov (United States)

    2011-06-01

    for regular objects by using dimensions and then volume formulae. But a better way is to do immersion and apply Archimedes principle . We do not have...of the material in each of the principle directions of an orthotropic material as demonstrated by Ong [1]. 12 If a sufficient number of these...closely analogous to a metal ‘plate- push ‘ experiment. There will be multiple wave interactions throughout the time frame of the experiment through

  6. Topology optimization of periodic microstructures for enhanced dynamic properties of viscoelastic composite materials

    DEFF Research Database (Denmark)

    Andreassen, Erik; Jensen, Jakob Søndergaard

    2014-01-01

    We present a topology optimization method for the design of periodic composites with dissipative materials for maximizing the loss/attenuation of propagating waves. The computational model is based on a finite element discretization of the periodic unit cell and a complex eigenvalue problem...

  7. Dynamics and Scaling Properties of Fractures in clay-like Materials

    Energy Technology Data Exchange (ETDEWEB)

    Walmann, Thomas

    1998-12-31

    Computer models that can help oil companies predict realistic and physically correct fracture patterns are important. To verify such a model, experiments described in this thesis were undertaken, using wet clay and powder. The main focus was on extensional fractures, but other types of fractures were also studied. High resolution digital images of the fracture patterns were recorded and analyzed using statistical physics and fractal geometry. The characteristic shapes and size distributions of individual fractures and the overall fracture patterns obtained from laboratory model studies were compared to results from aerial photographs of a fracture pattern in a collapsed glacier that had undergone a similar deformation. A new scaling relation (a power-law) between the length of a fracture and the projected area is derived for fractures formed during clay model experiments. This scaling relation is found also in a field study of a fracture pattern in a glacier. The forms of the different distributions that characterizes fractures in clay experiments are discussed. Several characteristic lengths are associated with the laboratory experiments. They are related to the sample size and shape, the model material and the nature of the imposed deformation. The roughness of the fracture traces obtained from powder experiments was found to have a self-affine form. The roughness, or Hurst exponent, was found to have the value 0.73, plus or minus 0.09. A large number of interacting fractures were formed in the systems studied, and under such conditions the fluctuations about the direction perpendicular to the principle strain direction are influenced by neighbouring fractures. As expected, an upper cutoff for the scaling range was observed. But the length at which the crossover from a self-affine shape to a flat shape took place did not depend systematically on any of the experimental parameters or characteristic length scales. The total fracture trace patterns could not be

  8. Earth materials and earth dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, K; Shankland, T. [and others

    2000-11-01

    In the project ''Earth Materials and Earth Dynamics'' we linked fundamental and exploratory, experimental, theoretical, and computational research programs to shed light on the current and past states of the dynamic Earth. Our objective was to combine different geological, geochemical, geophysical, and materials science analyses with numerical techniques to illuminate active processes in the Earth. These processes include fluid-rock interactions that form and modify the lithosphere, non-linear wave attenuations in rocks that drive plate tectonics and perturb the earth's surface, dynamic recrystallization of olivine that deforms the upper mantle, development of texture in high-pressure olivine polymorphs that create anisotropic velocity regions in the convecting upper mantle and transition zone, and the intense chemical reactions between the mantle and core. We measured physical properties such as texture and nonlinear elasticity, equation of states at simultaneous pressures and temperatures, magnetic spins and bonding, chemical permeability, and thermal-chemical feedback to better characterize earth materials. We artificially generated seismic waves, numerically modeled fluid flow and transport in rock systems and modified polycrystal plasticity theory to interpret measured physical properties and integrate them into our understanding of the Earth. This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL).

  9. Electrical properties of materials

    CERN Document Server

    Solymar, L; Syms, R R A

    2014-01-01

    An informal and highly accessible writing style, a simple treatment of mathematics, and clear guide to applications have made this book a classic text in electrical and electronic engineering. Students will find it both readable and comprehensive. The fundamental ideas relevant to the understanding of the electrical properties of materials are emphasized; in addition, topics are selected in order to explain the operation of devices having applications (or possible future applications) in engineering. The mathematics, kept deliberately to a minimum, is well within the grasp of a second-year student. This is achieved by choosing the simplest model that can display the essential properties of a phenomenom, and then examining the difference between the ideal and the actual behaviour. The whole text is designed as an undergraduate course. However most individual sections are self contained and can be used as background reading in graduate courses, and for interested persons who want to explore advances in microele...

  10. Properties of dynamical electromagnetic metamaterials

    Science.gov (United States)

    Padilla, Willie J.; Averitt, Richard D.

    2017-08-01

    Electromagnetic metamaterials consist of two or three dimensional arrays of tailored metallic and/or dielectric inclusions and provide unprecedented sub-wavelength control over light-matter interactions. Metamaterials are fashioned to yield a specific response to the electric and magnetic components of light and may be treated as effective media, described by effective optical constants {μ }{{eff}} and {{ɛ }}{{eff}}, and have realized a multitude of exotic properties difficult to achieve with natural materials. An inductive-capacitive unit cell geometry provides enhanced values of optical constants, as well as the ability to dynamically control the novel responses exhibited by electromagnetic metamaterials. The ability of metamaterials to achieve real-time dynamic properties has realized novel applications and has made them relevant for the next revolution in advanced materials and related devices.

  11. Dynamic Polymer Systems with Self-regulated Secretion for the Control of Surface Properties and Material Healing

    Science.gov (United States)

    2017-08-23

    secretes fluids, mediating defence, adhesion, wound healing , temperature—often several of these at once—through tightly self-regulated release systems6–9...s ) Silicone oil (wt%) a b e c Liquid medium Diffuse Open Close Damage Secrete Self- heal Gel phase St re ss (M Pa ) Strain (ii) (iii) (ii) 0 s...Secretion for the Control of Surface Properties and Material Healing Harvard University CAmbridge MA 242 Office of Naval Research Arlington 46 242 1

  12. Experimental study on the material dynamic fracture properties by Instrumented Charpy Impact test with single specimen method

    Science.gov (United States)

    Jian, F.; Fulian, D.; Chengzhong, W.

    2003-09-01

    With the determination of load-time curve recorded by Amsler/Roell RKP 450 Instrumented Charpy Impact test and based on the Newton's Second Law, Impact character of a single standard V-notch specimen of X70 pipeline steel under the low temperature -70 ^{circ}C was investigated by studying the impact energy distribution. It was revealed that maximum load point (Fm point) was not exact the dynamic crack initiation, which was detected somewhere prior and very close to Fm point by using Compliance Changing Rate method. This fact was also confirmed by Dynamic CTOD method. That is to say, Impact energy related to the Fm point (i.e. Em) consists not only the crack initiation energy Ei, but a small part of crack extension energy as well. Ratio of Ei/Em was found to be 0.90 just applicable to the material used here. Dynamic fracture toughness JJd was then estimated by modified Rice equation. Crack extension behavior and dynamic crack growth resistance curve (J-Δa) during stable crack propagation period was carefully analyzed by Key Curve method. Finally, methods for evaluating tearing module Tmat, and CTOD curve under the impact test were also briefly introduced in the paper.

  13. A density functional theory study on the thermodynamic and dynamic properties of anthraquinone analogue cathode materials for rechargeable lithium ion batteries.

    Science.gov (United States)

    Yang, Shu-Jing; Qin, Xiao-Ya; He, Rongxing; Shen, Wei; Li, Ming; Zhao, Liu-Bin

    2017-05-21

    Organic redox compounds have become the emerging electrode materials for rechargeable lithium ion batteries. The high electrochemical performance provides organic electrode materials with great opportunities to be applied in electric energy storage devices. Among the different types of organic materials, conjugated carbonyl compounds are the most promising type at present, because only they can simultaneously achieve, high energy density, high cycling stability, and high power density. In this research, a series of heteroatom substituted anthraquinone (AQ) derivatives were designed theoretically so that the high theoretical capacity of AQ remained. The discharge and charge mechanism as well as the thermodynamic and dynamic properties of AQ and its derivatives were investigated using first-principles density functional theory. Using heteroatom substitution, both the thermodynamic and dynamic properties of AQ as cathode materials could be largely improved. Among these conjugated carboxyl compounds, BDOZD and BDIOZD with a simultaneously high theoretical capacity and high working potential exhibit the largest energy density of about 780 W h kg(-1), which is 41% larger than that of AQ. The PQD with the smallest value of λ gives the largest charge transfer rate constant, which is about four times as large as the prototype molecule, AQ. The most interesting finding is that the lithium ion transfer plays a very important role in influencing both the discharge potential and electrochemical charge transfer rate. The present study illustrates that theoretical calculations provide a highly effective way to discover potential materials for use with rechargeable lithium ion batteries.

  14. Tensile material properties of human rib cortical bone under quasi-static and dynamic failure loading and influence of the bone microstucture on failure characteristics

    CERN Document Server

    Subit, Damien; Valazquez-Ameijide, Juan; Arregui-Dalmases, Carlos; Crandall, Jeff

    2011-01-01

    Finite element models of the thorax are under development to assist vehicle safety researchers with the design of countermeasures such as advanced restrain systems. Computational models have become more refined with increasing geometrical complexity as element size decreases. These finite element models can now capture small geometrical features with an attempt to predict fracture. However, the bone material properties currently available, and in particular the rate sensitivity, have been mainly determined from compression tests or tests on long bones. There is a need for a new set of material properties for the human rib cortical bone. With this objective, a new clamping technique was developed to test small bone coupons under tensile loading. Ten coupons were harvested from the cortical shell of the sixth and seventh left ribs from three cadavers. The coupons were tested to fracture under quasi-static (target strain rate of 0.07 %/s) and dynamic loading (target strain rate of 170 %/s). Prior to testing, eac...

  15. Fe Analysis of a Steam Turbine HP Rotor Blade Stage Concerning Material Effort, Dynamic Properties and Creep Damage Assessment

    Directory of Open Access Journals (Sweden)

    Borkowski Paweł

    2016-03-01

    Full Text Available This paper is concerned with the 1st stage of HP rotor blade assembly steam turbine TK 120. The methodology was focused on the selection of mechanical properties and the way of the rotor disc modeling and estimating the degree of damage caused by creep. Then the dynamic interference between the frequencies of excitation and the natural frequencies was assessed. Static calculations were performed for the cyclic sectors consisting of the disc, disc blades, spacers and shrouding, including loads as temperature, mass forces from the angular velocity and the pressure on the blades. Then, the creep analysis using a Norton’s model and the modal analysis were performed. Static analysis gave information concerning the distributions of displacements, stress and strain components. In the creep analysis, the creep displacements and stress relaxation versus time were determined and the estimated degree of damage caused by creep was evaluated at each part of the rotor disc. In the modal analysis, the natural frequencies and modes of vibrations corresponding to the nodal diameters were found. The results of modal analysis were shown in the SAFE graph. Numerical calculations have shown that the rotor disc was a well-designed structure and did not reveal any dynamic interference.

  16. ThermoData Engine (TDE): Software Implementation of the Dynamic Data Evaluation Concept. 8. Properties of Material Streams and Solvent Design

    DEFF Research Database (Denmark)

    Diky, Vladimir; Chirico, Robert D.; Muzny, Chris D.

    2013-01-01

    ThermoData Engine (TDE) is the first full-scale software implementation of the dynamic data evaluation concept, as reported in this journal. The present paper describes the first application of this concept to the evaluation of thermophysical properties for material streams involving any number......-liquid equilibrium). Multi-component models are based on those for the pure-components and all binary subsystems evaluated on demand through the TDE software algorithms. Models are described in detail, and extensions to the class structure of the program are provided. Novel program features, such as ready...... of chemical components with assessment of uncertainties. The method involves construction of Redlich-Kister type equations for individual properties (excess volume, thermal conductivity, viscosity, surface tension, and excess enthalpy) and activity-coefficient models for phase equilibrium properties (vapor...

  17. Modeling the Peano fluidic muscle and the effects of its material properties on its static and dynamic behavior

    Science.gov (United States)

    Veale, Allan Joshua; Xie, Sheng Quan; Anderson, Iain Alexander

    2016-06-01

    The promise of wearable assistive robotics cannot be realized without the development of actuators that mimic the behavior and form of biological muscles. Planar fluidic muscles known as Peano muscles or pouch motors have the potential to provide the high force and compliance of McKibben pneumatic artificial muscles with the low threshold pressure of pleated pneumatic artificial muscles. Yet they do so in a soft and slim form that can be discreetly distributed over the human body. This work is an investigation into the empirical modeling of the Peano muscle, the effect of its material on its performance, and its capabilities and limitations. We discovered that the Peano muscle could provide responsive and discreet actuation of soft and rigid bodies requiring strains between 15% and 30%. Ideally, they are made of non-viscoelastic materials with high tensile and low bending stiffnesses. While Sarosi et al’s empirical model accurately captures its static behavior with an root mean square error of 10.2 N, their dynamic model overestimates oscillation frequency and damping. We propose that the Peano muscle be modeled by a parallel ideal contractile unit and viscoelastic element, both in series with another viscoelastic element.

  18. Experiments showing dynamics of materials interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin, R.F. [Los Alamos National Lab., NM (United States). Dynamic Experimentation Div.

    1997-02-01

    The discipline of materials science and engineering often involves understanding and controlling properties of interfaces. The authors address the challenge of educating students about properties of interfaces, particularly dynamic properties and effects of unstable interfaces. A series of simple, inexpensive, hands-on activities about fluid interfaces provides students with a testbed to develop intuition about interface dynamics. The experiments highlight the essential role of initial interfacial perturbations in determining the dynamic response of the interface. The experiments produce dramatic, unexpected effects when initial perturbations are controlled and inhibited. These activities help students to develop insight about unstable interfaces that can be applied to analogous problems in materials science and engineering. The lessons examine ``Rayleigh-Taylor instability,`` an interfacial instability that occurs when a higher-density fluid is above a lower-density fluid.

  19. Dynamic fracture of heterogeneous materials

    Energy Technology Data Exchange (ETDEWEB)

    Stout, M.G.; Liu, C.; Addessio, F.L.; Williams, T.O.; Bennett, J.G.; Haberman, K.S.; Asay, B.W.

    1998-12-31

    This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The objective of this project was to investigate the fundamental aspects of the process of dynamic fracture propagation in heterogeneous materials. The work focused on three important, but poorly understood, aspects of dynamic fracture for materials with a heterogeneous microstructure. These were: the appropriateness of using a single-parameter asymptotic analysis to describe dynamic crack-tip deformation fields, the temperature rises at the tip and on the flanks of a running crack, and the constitutive modeling of damage initiation and accumulation.

  20. Optical properties of advanced materials

    CERN Document Server

    Kajikawa, Kotaro

    2013-01-01

    In the last decade, optically functionalized materials have developed rapidly, from bulk matters to structured forms. Now we have a rich variety of attractive advanced materials. They are applied to optical and electrical devices that support the information communication technology in the mid 21-th century. Accordingly, it is quite important to have a broad knowledge of the optical properties of advanced materials for students, scientists and engineers working in optics and related fields. This book is designed to teach fundamental optical properties of such advanced materials effectively. These materials have their own peculiarities which are very interesting in modern optical physics and also for applications because the concepts of optical properties are quite different from those in conventional optical materials. Hence each chapter starts to review the basic concepts of the materials briefly and proceeds to the practical use. The important topics covered in this book include:  quantum structures of sem...

  1. Porous Materials - Structure and Properties

    DEFF Research Database (Denmark)

    Nielsen, Anders

    1997-01-01

    The paper presents some viewpoints on the description of the pore structure and the modelling of the properties of the porous building materials. Two examples are given , where it has been possible to connect the pore structure to the properties: Shrinkage of autoclaved aerated concrete and the p......The paper presents some viewpoints on the description of the pore structure and the modelling of the properties of the porous building materials. Two examples are given , where it has been possible to connect the pore structure to the properties: Shrinkage of autoclaved aerated concrete...

  2. Dental materials with antibiofilm properties.

    Science.gov (United States)

    Wang, Zhejun; Shen, Ya; Haapasalo, Markus

    2014-02-01

    Oral bacteria have evolved to form biofilms on hard tooth surfaces and dental materials. The antibiofilm effect of materials used for the restoration of oral function affects oral health. In this review we describe the features involved in the formation of oral biofilms on different surfaces in the oral cavity and the antibiofilm properties of dental materials. An electronic search of scientific papers from 1987 to 2013 was performed with PubMed, ScienceDirect and Google search engines using the following search terms: antibiofilm, dental material, dental hard tissue, endodontic material, implant material, oral biofilm, and restorative material. Selected inclusion criteria resulted in 179 citations from the scientific, peer-reviewed literature. Oral biofilms form not only on dental hard tissue, but also on a wide range of dental materials used in cariology, endodontics, restorative dentistry and periodontology, resulting in destruction of dental hard tissue and even infection. Therefore, there has been a continuous effort to develop the antibiofilm properties of dental materials used for different purposes. Specific antimicrobial design in the composition and application of new materials (e.g. bioceramic sealer, resin composite, implant coating) demonstrates an improvement of the antibiofilm properties of these materials compared to earlier generations. A significant number of dental materials have been shown to affect biofilm growth by inhibiting the adhesion of bacteria, limiting their growth or killing microbes in the biofilms formed in vitro. Incorporation of an appropriate amount of antibacterial agent could provide dental materials with antibiofilm activity without significantly influencing their mechanical properties. However, more randomized and double-blind clinical studies of sufficient length with these materials are needed to confirm long term success following their use in the dental clinic. Copyright © 2013 Academy of Dental Materials. Published by

  3. Material Properties at Low Temperature

    CERN Document Server

    Duthil, P

    2014-01-01

    From ambient down to cryogenic temperatures, the behaviour of materials changes greatly. Mechanisms leading to variations in electrical, thermal, mechanical, and magnetic properties in pure metals, alloys, and insulators are briefly introduced from a general engineering standpoint. Data sets are provided for materials commonly used in cryogenic systems for design purposes.

  4. ThermoData Engine (TDE): software implementation of the dynamic data evaluation concept. 8. Properties of material streams and solvent design.

    Science.gov (United States)

    Diky, Vladimir; Chirico, Robert D; Muzny, Chris D; Kazakov, Andrei F; Kroenlein, Kenneth; Magee, Joseph W; Abdulagatov, Ilmutdin; Kang, Jeong Won; Gani, Rafiqul; Frenkel, Michael

    2013-01-28

    ThermoData Engine (TDE) is the first full-scale software implementation of the dynamic data evaluation concept, as reported in this journal. The present paper describes the first application of this concept to the evaluation of thermophysical properties for material streams involving any number of chemical components with assessment of uncertainties. The method involves construction of Redlich-Kister type equations for individual properties (excess volume, thermal conductivity, viscosity, surface tension, and excess enthalpy) and activity-coefficient models for phase equilibrium properties (vapor-liquid equilibrium). Multicomponent models are based on those for the pure-components and all binary subsystems evaluated on demand through the TDE software algorithms. Models are described in detail, and extensions to the class structure of the program are provided. Novel program features, such as ready identification of key measurements for subsystems that can reduce the combined uncertainty for a particular stream property, are described. In addition, new product-design features are described for selection of solvents for optimized crystal dissolution, separation of binary crystal mixtures, and solute extraction from a single-component solvent. Planned future developments are summarized.

  5. Mechanical Properties of Materials

    CERN Document Server

    Pelleg, Joshua

    2013-01-01

    The subject of mechanical behavior has been in the front line of basic studies in engineering curricula for many years.  This textbook was written for engineering students with the aim of presenting, in a relatively simple manner, the basic concepts of mechanical behavior in solid materials. A second aim of the book is to guide students in their laboratory experiments by helping them to understand their observations in parallel with the lectures of their various courses; therefore the first chapter of the book is devoted to mechanical testing. Another aim of the book is to provide practicing engineers with basic help to bridge the gap of time that has passed from their graduation up to their actual involvement in engineering work. The book also serves as the basis for more advanced studies and seminars when pursuing courses on a graduate level. The content of this textbook and the topics discussed correspond to courses that are usually taught in universities and colleges all over the world, but with a differ...

  6. Photorefractive optics materials, properties, and applications

    CERN Document Server

    Yu, Francis T S

    1999-01-01

    The advances of photorefractive optics have demonstrated many useful and practical applications, which include the development of photorefractive optic devices for computer communication needs. To name a couple significant applications: the large capacity optical memory, which can greatly improve the accessible high-speed CD-ROM and the dynamic photorefractive gratings, which can be used for all-optic switches for high-speed fiber optic networks. This book is an important reference both for technical and non-technical staffs who are interested in this field. * Covers the recent development in materials, phenomena, and applications * Includes growth, characterization, dynamic gratings, and liquid crystal PR effect * Includes applications to photonic devices such as large capacity optical memory, 3-D interconnections, and dynamic holograms * Provides the recent overall picture of current trends in photorefractive optics * Includes optical and electronic properties of the materials as applied to dynamic photoref...

  7. Nonlinear Dynamics of Structures with Material Degradation

    Science.gov (United States)

    Soltani, P.; Wagg, D. J.; Pinna, C.; Whear, R.; Briody, C.

    2016-09-01

    Structures usually experience deterioration during their working life. Oxidation, corrosion, UV exposure, and thermo-mechanical fatigue are some of the most well-known mechanisms that cause degradation. The phenomenon gradually changes structural properties and dynamic behaviour over their lifetime, and can be more problematic and challenging in the presence of nonlinearity. In this paper, we study how the dynamic behaviour of a nonlinear system changes as the thermal environment causes certain parameters to vary. To this end, a nonlinear lumped mass modal model is considered and defined under harmonic external force. Temperature dependent material functions, formulated from empirical test data, are added into the model. Using these functions, bifurcation parameters are defined and the corresponding nonlinear responses are observed by numerical continuation. A comparison between the results gives a preliminary insight into how temperature induced properties affects the dynamic response and highlights changes in stability conditions of the structure.

  8. Material properties in complement activation

    DEFF Research Database (Denmark)

    Moghimi, S. Moein; Andersen, Alina Joukainen; Ahmadvand, Davoud

    2011-01-01

    -immune performance’ relationship studies in nanomedicine research at many fronts. The interaction between nanomaterials and the complement system is complex and regulated by inter-related factors that include nanoscale size, morphology and surface characteristics. Each of these parameters may affect complement...... activation differently and through different sensing molecules and initiation pathways. The importance of material properties in triggering complement is considered and mechanistic aspects discussed. Mechanistic understanding of complement events could provide rational approaches for improved material design...

  9. Mechanical Properties of Composite Materials

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2014-10-01

    Full Text Available An examination has been made of the mechanical and failure properties of several composite materials, such as a short and a long carbon fiber reinforced plastic (short- and long-CFRP and metal based composite material. The short CFRP materials were used for a recycled CFRP which fabricated by the following process: the CFRP, consisting of epoxy resin with carbon fiber, is injected to a rectangular plate cavity after mixing with acrylonitrile butadiene styrene resin with different weight fractions of CFRP. The fatigue and ultimate tensile strength (UTS increased with increasing CFRP content. These correlations, however, break down, especially for tensile strength, as the CFPR content becomes more than 70%. Influence of sample temperature on the bending strength of the long-CFRP was investigated, and it appears that the strength slightly decreases with increasing the temperature, due to the weakness in the matrix. Broken fiber and pull-out or debonding between the fiber and matrix were related to the main failure of the short- and long-CFRP samples. Mechanical properties of metal based composite materials have been also investigated, where fiber-like high hardness CuAl2 structure is formed in aluminum matrix. Excellent mechanical properties were obtained in this alloy, e.g., the higher strength and the higher ductility, compared tothe same alloy without the fiber-like structure. There are strong anisotropic effects on the mechanical properties due to the fiber-like metal composite in a soft Al based matrix.

  10. Satellite material contaminant optical properties

    Science.gov (United States)

    Wood, B. E.; Bertrand, W. T.; Seiber, B. L.; Kiech, E. L.; Falco, P. M.; Holt, J. D.

    1990-03-01

    The Air Force Wright Research and Development Center and the Arnold Engineering Development Center are continuing a program for measuring optical effects of satellite material outgassing products on cryo-optic surfaces. Presented here are infrared (4000 to 700 cm(-1)) transmittance data for contaminant films condensed on a 77 K germanium window. From the transmittance data, the contaminant film refractive and absorptive indices (n, k) were derived using an analytical thin-film interference model with a nonlinear least-squares algorithm. To date 19 materials have been studied with the optical contents determined for 13 of those. The materials include adhesives, paints, composites, films, and lubricants. This program is continuing and properties for other materials will be available in the future.

  11. Dynamical Properties of Interaction Data

    CERN Document Server

    Bramson, Aaron

    2015-01-01

    Network dynamics are typically presented as a time series of network properties captured at each period. The current approach examines the dynamical properties of transmission via novel measures on an integrated, temporally extended network representation of interaction data across time. Because it encodes time and interactions as network connections, static network measures can be applied to this "temporal web" to reveal features of the dynamics themselves. Here we provide the technical details and apply it to agent-based implementations of the well-known SEIR and SEIS epidemiological models.

  12. Dynamic molecular crystals with switchable physical properties.

    Science.gov (United States)

    Sato, Osamu

    2016-06-21

    The development of molecular materials whose physical properties can be controlled by external stimuli - such as light, electric field, temperature, and pressure - has recently attracted much attention owing to their potential applications in molecular devices. There are a number of ways to alter the physical properties of crystalline materials. These include the modulation of the spin and redox states of the crystal's components, or the incorporation within the crystalline lattice of tunable molecules that exhibit stimuli-induced changes in their molecular structure. A switching behaviour can also be induced by changing the molecular orientation of the crystal's components, even in cases where the overall molecular structure is not affected. Controlling intermolecular interactions within a molecular material is also an effective tool to modulate its physical properties. This Review discusses recent advances in the development of such stimuli-responsive, switchable crystalline compounds - referred to here as dynamic molecular crystals - and suggests how different approaches can serve to prepare functional materials.

  13. High Speed Dynamics in Brittle Materials

    Science.gov (United States)

    Hiermaier, Stefan

    2015-06-01

    Brittle Materials under High Speed and Shock loading provide a continuous challenge in experimental physics, analysis and numerical modelling, and consequently for engineering design. The dependence of damage and fracture processes on material-inherent length and time scales, the influence of defects, rate-dependent material properties and inertia effects on different scales make their understanding a true multi-scale problem. In addition, it is not uncommon that materials show a transition from ductile to brittle behavior when the loading rate is increased. A particular case is spallation, a brittle tensile failure induced by the interaction of stress waves leading to a sudden change from compressive to tensile loading states that can be invoked in various materials. This contribution highlights typical phenomena occurring when brittle materials are exposed to high loading rates in applications such as blast and impact on protective structures, or meteorite impact on geological materials. A short review on experimental methods that are used for dynamic characterization of brittle materials will be given. A close interaction of experimental analysis and numerical simulation has turned out to be very helpful in analyzing experimental results. For this purpose, adequate numerical methods are required. Cohesive zone models are one possible method for the analysis of brittle failure as long as some degree of tension is present. Their recent successful application for meso-mechanical simulations of concrete in Hopkinson-type spallation tests provides new insight into the dynamic failure process. Failure under compressive loading is a particular challenge for numerical simulations as it involves crushing of material which in turn influences stress states in other parts of a structure. On a continuum scale, it can be modeled using more or less complex plasticity models combined with failure surfaces, as will be demonstrated for ceramics. Models which take microstructural

  14. The Characterization of Material Properties and Structural Dynamics of the Manduca Sexta Forewing for Application to Flapping Wing Micro Air Vehicle Design

    Science.gov (United States)

    2012-09-13

    hinge width, length, and thickness as where Eh is the Youngs modulus of the flexure hinge and wh, lh, th are the width, length, and thickness of the...Flight Muscles . . . . . . . . . . . . . . . . . . . 9 2.1.4 Wing Kinematics . . . . . . . . . . . . . . . . . 10 2.1.5 Wing Forces...Elastic Modulus . . . . . . . . . . . . 49 3.2 Membrane . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.2.1 Membrane Material Properties

  15. Estimation of hygroscopic of electrotechnical materials by dynamic speckle technique

    OpenAIRE

    Bertolini, Guillermo Ramón; Cabello, Carmen Inés; Arizaga, R.; Trivi, Marcelo Ricardo; Barbera, Gustavo Ariel

    2013-01-01

    Dynamic speckle laser (DLS) technique has been applied to the analysis of different biological systems, inorganic materials and industrial processes. In this paper, we use this technique to analyze the hygroscopic properties of different types of porcelain and papers for electrotechnical purposes. Experimental speckle results showed different behavior depending on physicochemical and textural properties of the samples.

  16. Dynamic Testing and Properties of Rubber O-rings and Their Application in Soft Drop Weight Tests of Low Strength Materials /

    OpenAIRE

    2014-01-01

    Mechanical behavior of low strength materials and elements at high strain rates was studied using a drop tower at UCSD. A commercial drop tower was modified to conduct high strain-rate impact compression tests. Instrumentations including strain gauges, accelerometers and a high speed camera were used to establish equilibrium conditions and stress strain relation of samples with high accuracy. Dynamic response of strongly nonlinear, viscoelastic toroidal rubber elements (o-rings) is studied. N...

  17. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    2005-01-01

    Provides detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors. This textbook emphasizes understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors and features an extensive collection of tables of material parameters, figures, and problems.

  18. Dynamic behavior of particulate/porous energetic materials

    Science.gov (United States)

    Nesterenko, Vitali F.; Chiu, Po-Hsun; Braithwaite, C. H.; Collins, Adam; Williamson, David Martin; Olney, Karl L.; Benson, David; McKenzie, Francesca

    2012-03-01

    Dynamic behavior of particulate/porous energetic materials in a broad range of dynamic conditions (low velocity impact and explosively driven expansion of rings) is discussed. Samples of these materials were fabricated using Cold Isostatic Pressing and Hot Isostatic Pressing with and without vacuum encapsulation. The current interest in these materials is due to the combination of their high strength and output of energy under critical conditions of mechanical deformation. They may exhibit high compressive and tensile strength with the ability to undergo bulk distributed fracture resulting in small size reactive fragments. The mechanical properties of these materials and the fragment sizes produced by fracturing are highly sensitive to mesostructure. For example, the dynamic strength of Al-W composites with fine W particles is significantly larger than the strength of composites with coarse W particles at the same porosity. The morphology of W inclusions had a strong effect on the dynamic strength and fracture pattern. Experimental results are compared with numerical data.

  19. Dynamic Properties of Offshore Wind Turbine Foundations

    DEFF Research Database (Denmark)

    Damgaard, Mads

    and material damping in the soil. Modal properties in terms of natural frequencies and corresponding damping ratios of offshore wind turbines are investigated by full-scale modal testing and simple numerical quasi-static simulations. The analyses show distinctly time-varying inherent modal properties that...... of the soil indicates that the modal properties and cross-wind fatigue loads of offshore wind turbines are strongly affected by the interrelation effects between the foundation and subsoil....... with static springs along the foundation and soil damping applied as modal damping. The methods, however, do not account for the dynamic stiffness due to inertia forces, and a welldefined representation of the dissipation effects in the soil is neglected. This in turn forms the basis of the current thesis...

  20. Dynamic teaching materials for ESSLLI

    NARCIS (Netherlands)

    Bernardi, R.B.; Dahn, I.; Mishne, G.A.; Moortgat, M.; de Rijke, M.; Uszkoreit, H.; Monachesi, P.; Vertan, C.; von Hahn, W.

    2004-01-01

    In the context of the European Network of Excellence in Computational Logic (CoLogNet, http://www.colognet.org/), the European Association for Logic, Language and Computation (FoLLI, http://www.folli.org) has started a project on E-Learning in Computational Logic and the development of Dynamic Teach

  1. Dynamic teaching materials for ESSLLI

    NARCIS (Netherlands)

    Bernardi, R.B.; Dahn, I.; Mishne, G.A.; Moortgat, M.; de Rijke, M.; Uszkoreit, H.; Monachesi, P.; Vertan, C.; von Hahn, W.

    2004-01-01

    In the context of the European Network of Excellence in Computational Logic (CoLogNet, http://www.colognet.org/), the European Association for Logic, Language and Computation (FoLLI, http://www.folli.org) has started a project on E-Learning in Computational Logic and the development of Dynamic Teach

  2. Dynamic teaching materials for ESSLLI

    NARCIS (Netherlands)

    Bernardi, R.B.; Dahn, I.; Mishne, G.A.; Moortgat, M.; de Rijke, M.; Uszkoreit, H.; Monachesi, P.; Vertan, C.; von Hahn, W.

    2004-01-01

    In the context of the European Network of Excellence in Computational Logic (CoLogNet, http://www.colognet.org/), the European Association for Logic, Language and Computation (FoLLI, http://www.folli.org) has started a project on E-Learning in Computational Logic and the development of Dynamic

  3. Dynamic compressive mechanical response of a soft polymer material

    NARCIS (Netherlands)

    Fan, J.T.; Weerheijm, J.; Sluys, L.J.

    2015-01-01

    The dynamic mechanical behaviour of a soft polymer material (Clear Flex 75) was studied using a split Hopkinson pressure bar (SHPB) apparatus. Mechanical properties have been determined at moderate to high strain rates. Real time deformation and fracture were recorded using a high-speed camera. Frac

  4. Spin-crossover materials properties and applications

    CERN Document Server

    Halcrow, Malcolm A

    2013-01-01

    The phenomenon of spin-crossover has a large impact on the physical properties of a solid material, including its colour, magnetic moment, and electrical resistance. Some materials also show a structural phase change during the transition. Several practical applications of spin-crossover materials have been demonstrated including display and memory devices, electrical and electroluminescent devices, and MRI contrast agents. Switchable liquid crystals, nanoparticles, and thin films of spin-crossover materials have also been achieved. Spin-Crossover Materials: Properties and Applicat

  5. Dynamic stress intensity factor KⅢ and dynamic crack propagation characteristics of anisotropic materials

    Institute of Scientific and Technical Information of China (English)

    GAO Xin; WANG Han-gong; KANG Xing-wu

    2008-01-01

    Based on the mechanics of anisotropic materials,the dynamic propagation problem of a mode Ⅲ crack in an infinite anisotropic body is investigated.Stress,strain and displacement around the crack tip are expressed as an analytical complex function,which can be represented in power series.Constant coefficients of series are determined by boundary conditions.Expressions of dynamic stress intensity factors for a mode Ⅲ crack are obtained.Components of dynamic stress,dynamic strain and dynamic displacement around the crack tip are derived.Crack propagation characteristics are represented by the mechanical properties of the anisotropic materials,i.e.,crack propagation velocity M and the parameter α.The faster the crack velocity is,the greater the maximums of stress components and dynamic displacement components around the crack tip are.In particular,the parameter α affects stress and dynamic displacement around the crack tip.

  6. Determination of Physical Properties of Carbon Materials by Results of Ablative Experiments Con-ducted in the Jets of Gas Dynamic Units

    Directory of Open Access Journals (Sweden)

    V. V. Gorsky

    2015-01-01

    Full Text Available The process of hypersonic vehicles’ movement in the dense layers of the atmosphere is accompanied by the considerable combustion of heat shield, which effects on the aerodynamic, mass-inertial and centering characteristics of the product.For correct calculation of model's movement parameters it is necessary:* Using the theoretical and computation methods for determining ablative characteristics of heat-protective materials;* Taking into account all the basic physical and chemical processes, involved in their ablation, using the above mentioned methods;* Testing these techniques in the wide range of experimental data. This physic-mathematical model of carbon materials (CM aerothermochemical destruction is based on using the following:* Arrhenius equations to calculate carbon kinetic oxidation;* Langmuir-Knudsen formula to calculate the velocity of non-equilibrium carbon’s sublimation;* Carbon erosion law represented as a unique dependence of this process velocity on the gas pressure on the wall.Mathematical description of all major processes included in this formulation of the problem, contains a number of "free" parameters that can be determined only on the basis of comparison of theoretical and experimental data according to total ablation characteristics of these materials.This comparison was performed in the article applicable to the tests conditions of modern CM in the stream of electric arc plant and in combustion products of liquid-propellant rocket engines.As the result, the data of kinetic of carbon oxidation by atomic oxygen at sublimation mode of material ablation were obtained for the first time. Carbon erosion law under high pressure was established for the first time.The new approach to processing of ablation experiments is enunciated. Using this approach allows to turn this experiments for CM from comparative tests into the tests to determine ablation properties of thermal protection. Moreover, it enables us also to use the

  7. Recent developments in dynamic testing of materials

    Directory of Open Access Journals (Sweden)

    Gilat Amos

    2015-01-01

    Full Text Available New techniques for dynamic characterization of materials that have been developed in the last three years (since the last DYMAT conference in 2012, and results from recent dynamic testing of Inconel 718 are presented. The first development is a dynamic punch test in which three dimensional Digital Image Correlation (DIC is used to measure the deformation of the rear surface of a specimen as it being penetrated. The second experimental technique that is under development is a dynamic tension experiment in which full-field strain measurement with DIC and full-field temperature measurement are done simultaneously during the test.

  8. Tailoring of epoxy material properties

    NARCIS (Netherlands)

    Nakka, J.S.

    2010-01-01

    This research work is aimed to understand the effect of resin chemistry on the physical properties (e.g. moduli, viscoelasticity, moisture uptake, coefficient of thermal expansion) of cured aromatic epoxy-amine thermoset resins. This understanding will result into a good first approximation of the f

  9. Fundamental properties of semiconductor materials, and material performance in detectors

    Science.gov (United States)

    Casper, K. J.

    1973-01-01

    Procedures for determining fundamental properties of semiconductor materials, their performance as radiation detectors, and their service life as such detectors are given. Relationships were established between the minority carrier lifetime in the bulk of the material and the charge collection efficiency of the detector.

  10. Properties and characterization of modern materials

    CERN Document Server

    Altenbach, Holm

    2017-01-01

    This book focuses on robust characterization and prediction methods for materials in technical applications as well as the materials’ safety features during operation. In particular, it presents methods for reliably predicting material properties, an aspect that is becoming increasingly important as engineering materials are pushed closer and closer to their limits to boost the performance of machines and structures. To increase their engineering value, components are now designed under the consideration of their multiphysical properties and functions, which requires much more intensive investigation and characterization of these materials. The materials covered in this monograph range from metal-based groups such as lightweight alloys, to advanced high-strength steels and modern titanium alloys. Furthermore, a wide range of polymers and composite materials (e.g. with micro- and nanoparticles or fibres) is covered. The book explores methods for property prediction from classical mechanical characterization-...

  11. Design of materials with prescribed nonlinear properties

    DEFF Research Database (Denmark)

    Wang, Fengwen; Sigmund, Ole; Jensen, Jakob Søndergaard

    2014-01-01

    We systematically design materials using topology optimization to achieve prescribed nonlinear properties under finite deformation. Instead of a formal homogenization procedure, a numerical experiment is proposed to evaluate the material performance in longitudinal and transverse tensile tests un....... The numerical examples illustrate optimized materials with rubber-like behavior and also optimized materials with extreme strain-independent Poisson's ratio for axial strain intervals of εi ∈ [0.00,0.30]. © 2014 Elsevier Ltd. All rights reserved....... under finite deformation, i.e. stress-strain relations and Poisson's ratio. By minimizing errors between actual and prescribed properties, materials are tailored to achieve the target. Both two dimensional (2D) truss-based and continuum materials are designed with various prescribed nonlinear properties...

  12. Learning targeted materials properties from data

    Science.gov (United States)

    Lookman, Turab; Balachandran, Prasanna V.; Dezhen, Xue; Theiler, James; Hogden, John

    We compare several strategies using a data set of 223 M2AX family of compounds for which the elastic properties [bulk (B), shear (G), and Young's (E) modulus] have been computed using density functional theory. The strategy is decomposed into two steps: a regressor is trained to predict elastic properties in terms of elementary orbital radii of the individual components of the materials; and a selector uses these predictions to choose the next material to investigate. The ultimate goal is to obtain a material with desired elastic properties. We examine how the choice of data set size, regressor and selector impact the results.

  13. Dynamic properties of composite cemented clay

    Institute of Scientific and Technical Information of China (English)

    蔡袁强; 梁旭

    2004-01-01

    In this work,the dynamic properties of composite cemented clay under a wide range of strains were studied considering the effect of different mixing ratio and the change of confining pressures through dynamic triaxial test. A simple and practical method to estimate the dynamic elastic modulus and damping ratio is proposed in this paper and a related empirical normalized formula is also presented. The results provide useful guidelines for preliminary estimation of cement requirements to improve the dynamic properties of clays.

  14. Charge carrier dynamics in photovoltaic materials

    NARCIS (Netherlands)

    Jensen, S.A.

    2014-01-01

    We employ the experimental technique THz Time Domain spectroscopy (THz-TDS) to study the optoelectronic properties of potential photovoltaic materials. This all-optical method is useful for probing photoconductivities in a range of materials on ultrafast timescales without the application of physica

  15. Magnetic materials fundamentals, products, properties, applications

    CERN Document Server

    Hilzinger, Rainer

    2013-01-01

    At a practical level, this compendium reviews the basics of soft and hard magnetic materials, discusses the advantages of the different processing routes for the exploitation of the magnetic properties and hence assists in proper, fail-safe and economic application of magnetic materials. Essential guidelines and formulas for the calculation of the magnetic and electrical properties, temperature and long-term stability of permanent magnets, of inductive components and magnetic shielding are compiled. Selected fields of application and case studies illustrate the large diversity of technical applications. Application engineers will appreciate the comprehensive compilation of the properties and detailed characteristic curves of modern soft and hard magnetic materials. Materials scientists will enjoy the presentation of the different processing routes and their impact on the magnetic properties and students will profit from the survey from the basics of magnetism down to the applications in inductive components, ...

  16. Dynamical simulations of strongly correlated electron materials

    Science.gov (United States)

    Kress, Joel; Barros, Kipton; Batista, Cristian; Chern, Gia-Wei; Kotliar, Gabriel

    We present a formulation of quantum molecular dynamics that includes electron correlation effects via the Gutzwiller method. Our new scheme enables the study of the dynamical behavior of atoms and molecules with strong electron interactions. The Gutzwiller approach goes beyond the conventional mean-field treatment of the intra-atomic electron repulsion and captures crucial correlation effects such as band narrowing and electron localization. We use Gutzwiller quantum molecular dynamics to investigate the Mott transition in the liquid phase of a single-band metal and uncover intriguing structural and transport properties of the atoms.

  17. Sandia Dynamic Materials Program Strategic Plan.

    Energy Technology Data Exchange (ETDEWEB)

    Flicker, Dawn Gustine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Benage, John F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Desjarlais, Michael P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Knudson, Marcus D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leifeste, Gordon T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lemke, Raymond W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mattsson, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wise, Jack L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Materials in nuclear and conventional weapons can reach multi-megabar pressures and 1000s of degree temperatures on timescales ranging from microseconds to nanoseconds. Understanding the response of complex materials under these conditions is important for designing and assessing changes to nuclear weapons. In the next few decades, a major concern will be evaluating the behavior of aging materials and remanufactured components. The science to enable the program to underwrite decisions quickly and confidently on use, remanufacturing, and replacement of these materials will be critical to NNSA’s new Stockpile Responsiveness Program. Material response is also important for assessing the risks posed by adversaries or proliferants. Dynamic materials research, which refers to the use of high-speed experiments to produce extreme conditions in matter, is an important part of NNSA’s Stockpile Stewardship Program.

  18. Temperature pattern dynamics in shocked porous materials

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The physical fields in porous materials under strong shock wave reaction are very complicated. We simulate such systems using the grain contact material point method. The complex temperature fields in the material are treated with the morphological characterization. To compare the structures and evolution of characteristic regimes under various temperature thresholds, we introduce two concepts, structure similarity and process similarity. It is found that the temperature pattern dynamics may show high similarity under various conditions. Within the same material, the structures and evolution of high-temperature regimes may show high similarity if the shock strength and temperature threshold are chosen appropriately. For process similarity in materials with high porosity, the required temperature threshold increases parabolically with the impact velocity. When the porosity becomes lower, the increasing rate becomes higher. For process similarity in different materials, the required temperature threshold and the porosity follow a power-law relationship in some range.

  19. Measurement of thermal properties of PCM materials

    Energy Technology Data Exchange (ETDEWEB)

    Domanski, R.; Jaworski, M. [Warsaw Univ. of Technology (Poland). Inst. of Heat Engineering

    1994-12-31

    In the article results of measurements of thermal properties of PCM (phase change materials) and their stability are presented. These include specific heat, temperature of phase change, latent heat and enthalpy as a function of temperature. Different kind of materials were considered, especially some waxes, n-alkanes and salt hydrates. Measurements of thermal capacity of materials were performed using two techniques - standard DSC (for small samples and pure materials) and simple thermal analysis based on the measurement of temperature field in relatively big samples (about 20-50 g). Stability of thermal properties in many cycles of melting and solidification for some materials obtained in special set-up (for fast cycling) are presented. On the base of measurements mathematical formulas describing enthalpy vs. temperature for some materials were developed. These are very useful in computer simulation of thermal storage systems with PCM. (orig.)

  20. Tribological Studies of Dynamic Thermal Seal Materials

    Science.gov (United States)

    DeMange, Jeffrey J.; Taylor, Shawn C.

    2016-01-01

    Thermal seals are required on high-speed vehicles in many dynamic applications such as variable inlets in propulsion systems and control surfaces. These seals, often referred to as dynamic thermal seals, must not only mitigate inboard heat transfer, but must also exhibit sufficient durability when scrubbed against mating surfaces. For high-temperature high-speed vehicle applications, the mating surfaces are often made from thermal protection system (TPS) materials, which are typically rougher and more abrasive than TPS materials used at lower temperatures. The high-temperature TPS materials used can include non-ablative (e.g., lightweight porous oxides, ceramic matrix composites) andor ablative systems (e.g., phenolic systems). Due to the increased need for durable high-temperature dynamic seals, researchers working with the NASA Glenn Research Center embarked on an effort to (a) characterize the tribological performance of state-of-the-art thermal seal materials against a variety of TPS materials and (b) develop approaches for improved wear resistance. Tests were conducted using a recently upgraded high-temperature tribometer to assess wear resistance for a variety of tribopairs under multiple conditions. This data will begin to frame the challenges of using these materials and eventually permit an improved ability to design and implement these critical TPS components.

  1. Study on the Numerical Simulation of a Cu Material's Dynamic Mechanical Property%某型铜材料动态力学性能的数值模拟研究

    Institute of Scientific and Technical Information of China (English)

    孙河洋; 马吉胜; 生龙波; 刘海平; 吴大林

    2011-01-01

    An efficient stress update algorithms was adopted, and a Vumat subroutine was programmed to introduce the Johnson-Cook constitute model by FORTRAN codes. The dynamic mechanical properties of a material were simulated under the condition of high speed impact and the influence of the large plasticity strain,high strain rate and temperature softening on the material's mechanical performance were studied.%采用一种高效的应力更新算法,运用Fortran语言编写Johnson-Cook本构模型的Vuamt子程序,模拟材料在高速冲击工况下的动态力学性能,研究塑性大应变、高应变率以及温度软化作用对材料力学性能的影响.

  2. Optical properties of low-dimensional materials

    CERN Document Server

    Ogawa, T

    1998-01-01

    This book surveys recent theoretical and experimental studies of optical properties of low-dimensional materials. As an extended version of Optical Properties of Low-Dimensional Materials (Volume 1, published in 1995 by World Scientific), Volume 2 covers a wide range of interesting low-dimensional materials including both inorganic and organic systems, such as disordered polymers, deformable molecular crystals, dilute magnetic semiconductors, SiGe/Si short-period superlattices, GaAs quantum wires, semiconductor microcavities, and photonic crystals. There are excellent review articles by promis

  3. Design and properties of maxillofacial prosthetic materials.

    Science.gov (United States)

    Andreopoulos, A G; Theophanides, T

    1993-11-01

    Maxillofacial reconstruction by prosthetic means is a valuable contribution that medicine offers to the public. Materials design and properties are the main problems faced by scientists in this field. Materials used for intraoral prostheses are not ideal, but they have been perfected to the point of practical use. Denture resins, gold, chromium-cobalt alloys, and porcelain are widely used and produce acceptable results in the oral cavity. In this review, the properties and performance of some polymeric materials used in maxillofacial prosthetics are discussed, and new trends in research and development are also reported.

  4. Bioactive glasses materials, properties and applications

    CERN Document Server

    Ylänen, Heimo

    2011-01-01

    Due to their biocompatibility and bioactivity, bioactive glasses are used as highly effective implant materials throughout the human body to replace or repair damaged tissue. As a result, they have been in continuous use since shortly after their invention in the late 1960s and are the subject of extensive research worldwide.Bioactive glasses provides readers with a detailed review of the current status of this unique material, its properties, technologies and applications. Chapters in part one deal with the materials and mechanical properties of bioactive glass, examining topics such

  5. From Microstructures to Predict Properties of Materials

    Science.gov (United States)

    Wang, Ke-Gang

    2010-03-01

    Understanding the precise and fundamental manner in which materials structures (nanostructures or microstructures) and their evolution influences properties and service lifetimes of advanced materials profoundly impacts material design and today materials design plays an increasingly important rôle in many engineering applications. Linking structures to properties and predicting properties of materials is fundamental step for materials design. First, a framework of applications of multiscale modeling to property prediction of advanced materials will be briefly presented. As an example, a methodology will be shown to link micro-scale to the continuum scale, integrating microstructure modeling with the large Thermo-Calc^ database. This paradigm was successfully applied to the case of Fe-12Ni-6Mn maraging steel. Next, methodology for integrating first-principle calculation into simulations of microstructure evolution will be reviewed. Our methods are sufficiently reliable to permit control and fabrication of quantum-dots structures, nanocrystals, and particle-reinforced nanocomposites, as well as assist in the predictive behavior of macro-scale colloids, aerosols, and other soft matter systems.

  6. Thermal protection materials: Thermophysical property data

    Science.gov (United States)

    Williams, S. D.; Curry, Donald M.

    1992-01-01

    This publication presents a thermophysical property survey on materials that could potentially be used for future spacecraft thermal protection systems (TPS). This includes data that was reported in the 1960's as well as more current information reported through the 1980's. An attempt was made to cite the manufacturers as well as the data source in the bibliography. This volume represents an attempt to provide in a single source a complete set of thermophysical data on a large variety of materials used in spacecraft TPS analysis. The property data is divided into two categories: ablative and reusable. The ablative materials have been compiled into twelve categories that are descriptive of the material composition. An attempt was made to define the Arrhenius equation for each material although this data may not be available for some materials. In a similar manner, char data may not be available for some of the ablative materials. The reusable materials have been divided into three basic categories: thermal protection materials (such as insulators), adhesives, and structural materials.

  7. Multifunctional Polycrystalline Ferroelectric Materials Processing and Properties

    CERN Document Server

    Pardo, Lorena

    2011-01-01

    This book presents selected topics on processing and properties of ferroelectric materials that are currently the focus of attention in scientific and technical research. Ferro-piezoelectric ceramics are key materials in devices for many applications, such as automotive, healthcare and non-destructive testing. As they are polycrystalline, non-centrosymmetric materials, their piezoelectricity is induced by the so-called poling process. This is based on the principle of polarization reversal by the action of an electric field that characterizes the ferroelectric materials. This book was born with the aim of increasing the awareness of the multifunctionality of ferroelectric materials among different communities, such as researchers, electronic engineers, end-users and manufacturers, working on and with ferro-piezoelectric ceramic materials and devices which are based on them. The initiative to write this book comes from a well-established group of researchers at the Laboratories of Ferroelectric Materials, Mate...

  8. Optical dynamic deformation measurements at translucent materials.

    Science.gov (United States)

    Philipp, Katrin; Koukourakis, Nektarios; Kuschmierz, Robert; Leithold, Christoph; Fischer, Andreas; Czarske, Jürgen

    2015-02-15

    Due to their high stiffness-to-weight ratio, glass fiber-reinforced polymers are an attractive material for rotors, e.g., in the aerospace industry. A fundamental understanding of the material behavior requires non-contact, in-situ dynamic deformation measurements. The high surface speeds and particularly the translucence of the material limit the usability of conventional optical measurement techniques. We demonstrate that the laser Doppler distance sensor provides a powerful and reliable tool for monitoring radial expansion at fast rotating translucent materials. We find that backscattering in material volume does not lead to secondary signals as surface scattering results in degradation of the measurement volume inside the translucent medium. This ensures that the acquired signal contains information of the rotor surface only, as long as the sample surface is rough enough. Dynamic deformation measurements of fast-rotating fiber-reinforced polymer composite rotors with surface speeds of more than 300 m/s underline the potential of the laser Doppler sensor.

  9. Accretion Dynamics on Wet Granular Materials.

    Science.gov (United States)

    Saingier, Guillaume; Sauret, Alban; Jop, Pierre

    2017-05-19

    Wet granular aggregates are common precursors of construction materials, food, and health care products. The physical mechanisms involved in the mixing of dry grains with a wet substrate are not well understood and difficult to control. Here, we study experimentally the accretion of dry grains on a wet granular substrate by measuring the growth dynamics of the wet aggregate. We show that this aggregate is fully saturated and its cohesion is ensured by the capillary depression at the air-liquid interface. The growth dynamics is controlled by the liquid fraction at the surface of the aggregate and exhibits two regimes. In the viscous regime, the growth dynamics is limited by the capillary-driven flow of liquid through the granular packing to the surface of the aggregate. In the capture regime, the capture probability depends on the availability of the liquid at the saturated interface, which is controlled by the hydrostatic depression in the material. We propose a model that rationalizes our observations and captures both dynamics based on the evolution of the capture probability with the hydrostatic depression.

  10. Tensile Properties of Fiber Materials under Different Strain Rates

    Institute of Scientific and Technical Information of China (English)

    XIONG Jie; GU Bo-hong; WANG Shan-yuan

    2002-01-01

    The quasi-static and dynamic tensile tests of aranid and high strength PVA fiber bundles are carried out under a wider range of strain rate by use of MTS (Materials Testing System) and bar-bar tensile impact apparatus.The influences of strain rate on mechanical properties of aramid and high strength polyvinyl alcohol fibers ar estudied. Micro failure mechanisms of fibers at different strain rates are examined by means of SEM.

  11. Interface Properties in Extruded FRC-Materials

    DEFF Research Database (Denmark)

    Stang, Henrik

    1997-01-01

    In a research and development project recently carried out at Department of Structural Engineering and Materials, Technical University of Denmark a new extrusion process for HPFRCC-materials was demonstrated.It is shown that superior interfacial properties are obtained in a polypropylene fiber...... reinforced cementitious material extruded by the developed process. It is further more shown that the fiber-matrix bond is highly dependent on the relative slip at the interface and a bond-slip relationship is suggested for the extruded material. The observed very high fiber-matrix bond is explained...... by the densification of the interfacial matrix material which has taken place during the consolidation process and which can be observed in the thin-section analysis....

  12. Mechanical properties of wet granular materials

    Energy Technology Data Exchange (ETDEWEB)

    Fournier, Z; Geromichalos, D; Herminghaus, S; Kohonen, M M; Mugele, F; Scheel, M; Schulz, M; Schulz, B; Schier, Ch; Seemann, R; Skudelny, A

    2005-03-09

    We elaborate on the impact of liquids upon the mechanical properties of granular materials. We find that most of the experimental and simulation results may be accounted for by a simple model assuming frictionless, spherical grains, with a hysteretic attractive interaction between neighbouring grains due to capillary forces.

  13. A reference material for dynamic displacement calibration

    Science.gov (United States)

    Davighi, A.; Hack, E.; Patterson, E.; Whelan, M.

    2010-06-01

    Calibration of displacement and strain measurement systems is an essential step in providing traceability and confidence in stress and strain distributions obtained from experiment and used to validate simulations employed in engineering design. Reference materials provide a simple, well-defined distribution of the measured quantity that can be traced to an international standard and can be used to assess the uncertainty associated with the measurement system. Previous work has established a reference material and procedure for calibrating optical systems for measuring static, in-plane strain distributions and also demonstrated its use. A new effort is in progress to extend this work to the measurement of three-dimensional displacement distributions induced by cyclic and dynamic loading, including transients and large-scale deformation. The first step in this effort has been to define both the essential and desirable attributes of a reference material for calibrating systems capable of measurements of dynamic displacement and strain. An international consortium of research laboratories, system designers, manufacturers and end-users has identified a list of attributes and members of the experimental mechanics community have been asked to weight the importance of these attributes. The attributes are being utilised to evaluate candidate designs for the reference material which have been generated through a series of brain-storming sessions within the consortium.

  14. New hose materials for dynamic loads

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, P.; Weber, J.; Wohlfarth, L. [Volkswagen AG, Wolfsburg (Germany)

    2001-07-01

    Dynamically stressed hoses continue to represent a challenge in the various areas where they are used in the automobile. This is true not only as regards the selection of suitable hose materials but also the necessary reinforcement technology. This is due to increasing requirements for temperature and chemical resistance resulting from new and further developments in the field of engines and assemblies. In addition to the 'classic' hose materials with internal and external elastomeric layers in conjunction with reinforcing elements (for example, servo hose or brake hose materials), the beginning of the 1990s saw increasing interest on the part of the automotive industry in hose and pipe materials made of thermoplastic elastomers (for example, TEEE) in the fields of intake and crankcase ventilation as well as plastic / rubber composite concepts for hoses. These plastic / rubber composite designs in particular are to be regarded as tailor-made problem solutions for specific functional and environmental aspects (minimisation of the permeation / emission of liquid or gaseous substances) in conjunction with a dynamic load-bearing capacity. (orig.)

  15. Design of advanced materials for linear and nonlinear dynamics

    DEFF Research Database (Denmark)

    Frandsen, Niels Morten Marslev

    The primary catalyst of this PhD project has been an ambition to design advanced materials and structural systems including, and possibly even exploiting, nonlinear phenomena such as nonlinear modal interaction leading to energy conversion between modes. An important prerequisite for efficient...... design is accurate and somewhat simple analysis tools, as well as a fundamental understanding of the physical phenomena responsible for the relevant effects. The emphasis of this work lies primarily in the investigation of various advanced material models, developing the necessary analytical tools...... to reveal the fundamental dynamic characteristics and thus the relevant design parameters.The thesis is built around the characterization of two one-dimensional, periodic material systems. The first is a nonlinear mass-spring chain with periodically varying material properties, representing a simple...

  16. The materials physics companion

    CERN Document Server

    Fischer-Cripps, Anthony C

    2014-01-01

    Introduction to Materials Physics: Structure of matter. Solid state physics. Dynamic properties of solids. Dielectric Properties of Materials: Dielectric properties. Ferroelectric and piezoelectric materials. Dielectric breakdown. Applications of dielectrics. Magnetic Properties of Materials: Magnetic properties. Magnetic moment. Spontaneous magnetization. Superconductivity.

  17. Static and dynamic properties of Fibonacci multilayers

    Science.gov (United States)

    Machado, L. D.; Bezerra, C. G.; Correa, M. A.; Chesman, C.; Pearson, J. E.; Hoffmann, A.

    2013-05-01

    We theoretically investigate static and dynamic properties of quasiperiodic magnetic multilayers. We considered identical ferromagnetic layers separated by non-magnetic spacers with two different thicknesses chosen based on the Fibonacci sequence. Using parameters for Fe/Cr, the minimum energy was determined and the equilibrium magnetization directions found were used to calculate magnetoresistance curves. Regarding dynamic behavior, ferromagnetic resonance (FMR) curves were calculated using an approximation known from the literature. Our numerical results illustrate the effects of quasiperiodicity on the static and dynamic properties of these structures.

  18. 粘弹性阻尼材料动态力学性能温度谱模型%Temperature Spectrum Model of Dynamic Mechanical Properties for Viscoelastic Damping Materials

    Institute of Scientific and Technical Information of China (English)

    张针粒; 李世其; 朱文革

    2011-01-01

    粘弹性阻尼材料的动态力学性能通常以时温叠加得到的频率谱主曲线表征,而时温叠加过程需要测量多个温度下的频率谱,难以保证试验条件的一致性.为此,由时温叠加原理,提出频率谱—温度谱镜像关系的数学形式.基于频率谱五参数分数微分模型,提出粘弹性阻尼材料的动态力学性能温度谱六参数分数微分模型,简称温度谱模型.所提模型能直接利用动态机械分析的试验结果,对于损耗模量和损因子具有对称性或非对称性的情形均适用.温度谱模型的参数具有明确的物理含义,推导温度谱模型参数的初值公式,并给出参数辨识步骤.不同材料在不同测试条件下的动态机械分析试验表明,所提模型可较好地表征粘弹性阻尼材料动态力学性能随温度的变化.%The dynamic mechanical properties of viscoelastic damping materials are usually represented by the master curve (MC) in the frequency domain. In order to construct a MC, multiple frequency spectrums must be tested, in which case it's difficult to maintain the same test conditions. A mathematical form of the mirror relationship between the temperature spectrum and frequency spectrum is suggested according to the time-temperature superposition principle. Based on the five-parameter fractional derivative frequency spectrum model, a six-parameter fractional derivative temperature spectrum model of dynamic mechanical properties, temperature spectrum model for short, is established for viscoelastic damping materials. The proposed model can directly use the results of dynamic mechanical analysis (DMA), and is applicable whether the loss modulus and loss factor are symmetrical or asymmetrical. The six parameters in the model all have clear physical meanings, and some formulas are derived to obtain their initial values, which can be refined by the suggested parameter identification procedure. DMA tests using different materials under

  19. Atomistic Simulations of Material Properties under Extreme Conditions

    Science.gov (United States)

    An, Qi

    Extreme conditions involve low or high temperatures (> 1500 K), high pressures (> 30 MPa), high strains or strain rates, high radiation fluxes (> 100 dpa), and high electromagnetic fields (> 15T). Material properties under extreme conditions can be extremely different from those under normal conditions. Understanding material properties and performance under extreme conditions, including their dynamic evolution over time, plays an essential role in improving material properties and developing novel materials with desired properties. To understand material properties under extreme conditions, we use molecular dynamics (MD) simulations with recently developed reactive force fields (ReaxFF) and traditional embedded atom methods (EAM) potentials to examine various materials (e.g., energetic materials and binary liquids) and processes. The key results from the simulations are summarized below. Anisotropic sensitivity of RDX crystals: Based on the compress-and-shear reactive dynamics (CS-RD) simulations of cyclotrimethylene trinitramine (RDX) crystals, we predict that for mechanical shocks between 3 and 7 GPa, RDX is the most sensitive to shocks perpendicular to the (100) and (210) planes, while it is insensitive to those perpendicular to the (120), (111), and (110) planes. The simulations demonstrate that the molecular origin of anisotropic shock sensitivity is the steric hindrance to shearing of adjacent slip planes. Mechanisms of hotspot formation in polymer bonded explosives (PBXs): The simulations of a realistic model of PBXs reveal that hotspots may form at the nonplanar interfaces where shear relaxation leads to a dramatic temperature increase that persists long after the shock front has passed the interface. For energetic materials this temperature increase is coupled to chemical reactions that eventually lead to detonation. We show that decreasing the density of the binder eliminates the hotspots or reduces the sensitivity. Cavitation in binary metallic liquids

  20. Dynamic modelling of packaging material flow systems.

    Science.gov (United States)

    Tsiliyannis, Christos A

    2005-04-01

    A dynamic model has been developed for reused and recycled packaging material flows. It allows a rigorous description of the flows and stocks during the transition to new targets imposed by legislation, product demand variations or even by variations in consumer discard behaviour. Given the annual reuse and recycle frequency and packaging lifetime, the model determines all packaging flows (e.g., consumption and reuse) and variables through which environmental policy is formulated, such as recycling, waste and reuse rates and it identifies the minimum number of variables to be surveyed for complete packaging flow monitoring. Simulation of the transition to the new flow conditions is given for flows of packaging materials in Greece, based on 1995--1998 field inventory and statistical data.

  1. Optical properties of photochromic and thermochromic materials

    Science.gov (United States)

    Mo, Yeon-Gon

    The optical properties of some thin film materials can be altered by an external stimulus. Photochromic and thermochromic materials, including inorganic and organic substances, have optical properties that can be changed in a reversible manner by irradiation and temperature respectively. These materials can be used in applications such as radiation or thermal sensors, information storage devices and smart window applications in buildings and cars. In this work, major effort was concentrated on passive thermal control coatings based on photochromic and thermochromic materials. The inorganic photochromic materials were based on tungsten and molybdenum oxide films and the organic photochromic materials included spiropyrans and spirooxazines. In addition, photochromic composite organic-inorganic films and thermochromic vanadium oxide films were prepared. The samples were synthesized using sputtering, sol-gel process, and thermal oxidation. The optical properties were investigated for the first time by ultraviolet/visible/infrared (UV/VIS/IR) spectroscopic ellipsometry, attenuated total reflection (ATR) infrared ellipsometry, spectrophotometry, and X-ray diffraction (XRD). For amorphous oxide films, the oxygen deficiency was important in determining the photochromic properties of the films. In the mid-infrared region, no photochromism was observed for the films. The optical properties of organic-inorganic composite films changed in the VIS/NIR wavelength region markedly in a reversible process, with UV irradiation. The composite films containing tungsten heteropolyoxometalate (HPOM) showed faster coloration and bleaching than pure tungsten oxide films. The composite films with molybdenum HPOM showed faster coloration and much slower bleaching than tungsten HPOM. The spiropyran and spirooxazine doped polymeric films were investigated for the first time using infrared and ATR ellipsometry. The infrared optical functions obtained by ATR measurements were a little smaller

  2. Material Discovery and Design with Dynamic Charge Reactive Potentials

    Science.gov (United States)

    Sinnott, Susan

    2015-03-01

    Atomic scale computational simulations of multi-phase systems is increasingly important as our ability to simulate nanometer-sized systems becomes routine. The recently developed charge optimized many body potential (COMB) potentials have significantly enhanced our ability to carry out atomic-scale simulations of heterogeneous material systems. The formalism of this potential combines variable charge electrostatic interactions with a classical analytical bond-order potential. It therefore has the capacity to adaptively model metallic, covalent, ionic, and van der Waals bonding within the same simulation cell and dynamically determine the charges on individual atoms according to the local environment. The utility of the COMB potentials is illustrated for materials design and discovery by exploring the structure, stability, mechanical properties, and thermal properties of intermetallic systems and oxide-metal interfaces. They are also used to address key questions associated with corrosion, thin film growth, and heterogeneous catalysis.

  3. Ultrafast control and monitoring of material properties using terahertz pulses

    Energy Technology Data Exchange (ETDEWEB)

    Bowlan, Pamela Renee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Lab. for Ultrafast Materials Optical Science (LUMOS)

    2016-05-02

    These are a set of slides on ultrafast control and monitoring of material properties using terahertz pulses. A few of the topics covered in these slides are: How fast is a femtosecond (fs), Different frequencies probe different properties of molecules or solids, What can a THz pulse do to a material, Ultrafast spectroscopy, Generating and measuring ultrashort THz pulses, Tracking ultrafast spin dynamics in antiferromagnets through spin wave resonances, Coherent two-dimensional THz spectroscopy, and Probing vibrational dynamics at a surface. Conclusions are: Coherent two-dimensional THz spectroscopy: a powerful approach for studying coherence and dynamics of low energy resonances. Applying this to graphene we investigated the very strong THz light mater interaction which dominates over scattering. Useful for studying coupled excitations in multiferroics and monitoring chemical reactions. Also, THz-pump, SHG-probe spectoscopy: an ultrafast, surface sensitive probe of atomic-scale symmetry changes and nonlinear phonon dymanics. We are using this in Bi2Se3 to investigate the nonlinear surface phonon dynamics. This is potentially very useful for studying catalysis.

  4. ASSESSMENT OF THE DYNAMIC PROPERTIES OF PLAIN AND RUBBERIZED CONCRETE

    Directory of Open Access Journals (Sweden)

    Ionuţ Ovidiu TOMA

    2015-11-01

    Full Text Available The use of rubber from discarded car tires as an alternative to natural aggregates in concrete may help preventing the complete depletion of natural resources and work towards a sustainable future. Moreover it can significantly reduce the environmental footprint of the construction industry. The assessment of the dynamic properties of a material are very important from the point of view of the energy dissipation capability of the investigated material. This can be determined from the dynamic modulus of elasticity, damping and the loss coefficients of the material. The paper presents the results obtained during an experimental program aimed at assessing the dynamic characteristics of plain and rubberized concrete containing rubber crumbs from discarded car tires. The theoretical background and the investigation methodology are presented with particular application to cylindrical concrete specimens.

  5. Properties of nanoclay PVA composites materials

    Directory of Open Access Journals (Sweden)

    Mohamed H. M. Ali

    2012-03-01

    Full Text Available Polyvinyl alcohol (PVA/ Na-rich Montmorillonite (MMT nanocomposites were prepared using solution method to create polymer-clay nanocomposite (PCN material. The PCN material was studied using X-ray diffraction (XRD, demonstrating polymer-clay intercalation that has a high d-spacing (lower diffraction angles in the PCN XRD pattern, compared to the pure MMT clay XRD pattern, which has a low d-spacing (high diffraction angles. The nano-scanning electron microscope (NSEM was used to study the morphological image of the PVA, MMT and PCN materials. The results showed that intercalation that took place between the PVA and MMT produced the PCN material. The mechanical properties of the pure PVA and the intercalated polymer material were studied. It was found that the small amount of MMT clay made the tensile modulus and percentage of the total elongation of the nano-composite significantly higher than the pure PVA polymer value, due to polymer-clay intercalation. The thermal stability of the intercalated polymer has been studied using thermal analytical techniques such as thermogravimetric analysis (TGA and differential scanning calorimetry (DSC. The results showed that the PCN material is more thermally stable than the pure PVA polymer.

  6. On Structure and Properties of Amorphous Materials

    Directory of Open Access Journals (Sweden)

    Zbigniew H. Stachurski

    2011-09-01

    Full Text Available Mechanical, optical, magnetic and electronic properties of amorphous materials hold great promise towards current and emergent technologies. We distinguish at least four categories of amorphous (glassy materials: (i metallic; (ii thin films; (iii organic and inorganic thermoplastics; and (iv amorphous permanent networks. Some fundamental questions about the atomic arrangements remain unresolved. This paper focuses on the models of atomic arrangements in amorphous materials. The earliest ideas of Bernal on the structure of liquids were followed by experiments and computer models for the packing of spheres. Modern approach is to carry out computer simulations with prediction that can be tested by experiments. A geometrical concept of an ideal amorphous solid is presented as a novel contribution to the understanding of atomic arrangements in amorphous solids.

  7. Dynamic Characterization of Thin Film Magnetic Materials

    Science.gov (United States)

    Gu, Wei

    A broadband dynamic method for characterizing thin film magnetic material is presented. The method is designed to extract the permeability and linewidth of thin magnetic films from measuring the reflection coefficient (S11) of a house-made and short-circuited strip line testing fixture with or without samples loaded. An adaptive de-embedding method is applied to remove the parasitic noise of the housing. The measurements were carried out with frequency up to 10GHz and biasing magnetic fields up to 600 Gauss. Particular measurement setup and 3-step experimental procedures are described in detail. The complex permeability of a 330nm thick continuous FeGaB, 435nm thick laminated FeGaB film and a 100nm thick NiFe film will be induced dynamically in frequency-biasing magnetic field spectra and compared with a theoretical model based on Landau-Lifshitz-Gilbert (LLG) equations and eddy current theories. The ferromagnetic resonance (FMR) phenomenon can be observed among these three magnetic materials investigated in this thesis.

  8. OPTICAL AND DYNAMIC PROPERTIES OF UNDOPED AND DOPED SEMICONDUCTOR NANOSTRUCTURES

    Energy Technology Data Exchange (ETDEWEB)

    Grant, C D; Zhang, J Z

    2007-09-28

    This chapter provides an overview of some recent research activities on the study of optical and dynamic properties of semiconductor nanomaterials. The emphasis is on unique aspects of these properties in nanostructures as compared to bulk materials. Linear, including absorption and luminescence, and nonlinear optical as well as dynamic properties of semiconductor nanoparticles are discussed with focus on their dependence on particle size, shape, and surface characteristics. Both doped and undoped semiconductor nanomaterials are highlighted and contrasted to illustrate the use of doping to effectively alter and probe nanomaterial properties. Some emerging applications of optical nanomaterials are discussed towards the end of the chapter, including solar energy conversion, optical sensing of chemicals and biochemicals, solid state lighting, photocatalysis, and photoelectrochemistry.

  9. The Characterization of Material Properties and Structural Dynamics of the Manduca Sexta Forewing for Application to Flapping Wing Micro Air Vehicle Design

    Science.gov (United States)

    O'Hara, Ryan P.

    Collateral damage presents a significant risk during air drops and airstrikes, risking citizens' lives and property, straining the relationship between the United States Air Force and host nations. This dissertation presents a methodology to determine the optimal location for making supply airdrops in order to minimize collateral damage while maintaining a high likelihood of successful recovery. A series of non-linear optimization algorithms are presented along with their relative success in finding the optimal location in the airdrop problem. Additionally, we present a quick algorithm for accurately creating the Pareto frontier in the multi-objective airstrike problem. We demonstrate the effect of differing guidelines, damage functions, and weapon employment selection which significantly alter the location of the optimal aimpoint in this targeting problem. Finally, we have provided a framework for making policy decisions in fast-moving troops-in-contact situations where observers are unsure of the nature of possible enemy forces in both finite and infinite time horizon problems. Through a recursive technique of solving this Markov decision process we have demonstrated the effect of improved intelligence and differing weights in the face of uncertain situations.

  10. Finite amplitude effects on drop levitation for material properties measurement

    Science.gov (United States)

    Ansari Hosseinzadeh, Vahideh; Holt, R. Glynn

    2017-05-01

    The method of exciting shape oscillation of drops to extract material properties has a long history, which is most often coupled with the technique of acoustic levitation to achieve non-contact manipulation of the drop sample. We revisit this method with application to the inference of bulk shear viscosity and surface tension. The literature is replete with references to a "10% oscillation amplitude" as a sufficient condition for the application of Lamb's analytical expressions for the shape oscillations of viscous liquids. Our results show that even a 10% oscillation amplitude leads to dynamic effects which render Lamb's results inapplicable. By comparison with samples of known viscosity and surface tension, we illustrate the complicating finite-amplitude effects (mode-splitting and excess dissipation associated with vorticity) that can occur and then show that sufficiently small oscillations allow us to recover the correct material properties using Lamb's formula.

  11. Mechanical Properties of Materials with Nanometer Scale Microstructures

    Energy Technology Data Exchange (ETDEWEB)

    William D. Nix

    2004-10-31

    We have been engaged in research on the mechanical properties of materials with nanometer-scale microstructural dimensions. Our attention has been focused on studying the mechanical properties of thin films and interfaces and very small volumes of material. Because the dimensions of thin film samples are small (typically 1 mm in thickness, or less), specialized mechanical testing techniques based on nanoindentation, microbeam bending and dynamic vibration of micromachined structures have been developed and used. Here we report briefly on some of the results we have obtained over the past three years. We also give a summary of all of the dissertations, talks and publications completed on this grant during the past 15 years.

  12. Dynamic Properties of Impulse Measuring Systems

    DEFF Research Database (Denmark)

    Pedersen, A.; Lausen, P.

    1971-01-01

    After some basic considerations the dynamic properties of the measuring system are subjected to a general examination based on a number of responses, characteristic of the system. It is demonstrated that an impulse circuit has an internal impedance different from zero, for which reason the intera......After some basic considerations the dynamic properties of the measuring system are subjected to a general examination based on a number of responses, characteristic of the system. It is demonstrated that an impulse circuit has an internal impedance different from zero, for which reason...

  13. AGC 2 Irradiated Material Properties Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rohrbaugh, David Thomas [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-05-01

    The Advanced Reactor Technologies Graphite Research and Development Program is conducting an extensive graphite irradiation experiment to provide data for licensing of a high temperature reactor (HTR) design. In past applications, graphite has been used effectively as a structural and moderator material in both research and commercial high temperature gas cooled reactor designs. , Nuclear graphite H 451, used previously in the United States for nuclear reactor graphite components, is no longer available. New nuclear graphite grades have been developed and are considered suitable candidates for new HTR reactor designs. To support the design and licensing of HTR core components within a commercial reactor, a complete properties database must be developed for these current grades of graphite. Quantitative data on in service material performance are required for the physical, mechanical, and thermal properties of each graphite grade, with a specific emphasis on data accounting for the life limiting effects of irradiation creep on key physical properties of the HTR candidate graphite grades. Further details on the research and development activities and associated rationale required to qualify nuclear grade graphite for use within the HTR are documented in the graphite technology research and development plan.

  14. Synthesis of new materials with properties ameliorated

    Science.gov (United States)

    Baira, F.; Benfarhi, S.; Zidani, S.

    2012-09-01

    Cellulose is the most abundant polymer in nature. It is used mainly for the production of paper bet also as a reinforcement in the polymer matrixes[1]. The modification of this polysaccharide presents a great interest, for it is the main constituent of agricultural wastes. It is well known that the microcrystalline cellulose gives, after chemical modification, new biodegradable materials[2], which may be used, for instance, for packaging. The esterification of cellulose necessitates an acid pretreatment which makes hydroxyl groups more accessible by breaking hydrogen bonds. X-rays diffraction analysis showed a feeble diminution of the treated samples cristallinity[3]. Cellulose, activated in this way, is esterified in a classic way in DMF, in the presence of triethylamine, LiCl and acid chloride at 60C° for 24 hours[4]. The obtained ester is precipitated in MeOH. The residue, dissolved in CHCl3, gives after evaporation in the open air, a plastic film surface. The water drop test has shown the hydrophobe properties of the plastic film surface. Our work is the study of the preparation of composite materials from the basis of their derivatives. Well as the study of the photopolymerisation kinetic, and the chemical degradation. The obtained films were analyzed by IR-TF, and the volumetrie[5,6]. As a conclusion, we have prepared composite materials with improved properties with reference to the matrix alone.

  15. Wear Property of Cast Steel Wheel Material in Rail Truck

    Institute of Scientific and Technical Information of China (English)

    MI Guo-fa; LIU Yan-lei; ZHANG Bin; FU Xiu-qin; ZHANG Hong; SONG Guo-xiang

    2009-01-01

    Wear property of material plays a key role in the service time of workpiece.A major objective in the development of new wheel materials is to improve the wear performance.The wear property of B and B+ grade cast steel materials was reported.The results showed that B+ grade cast steel material exhibited better wear property than the B grade material.Carbon content related to the hardness match was the principal factor affecting the wear properties.

  16. Dynamic damping property of magnetorheological elastomer

    Institute of Scientific and Technical Information of China (English)

    李剑锋; 龚兴龙

    2008-01-01

    Magnetorheological elastomer(MRE) is a new kind of smart materials,its dynamic mechanic performances can be controlled by an applied magnetic field.MRE is usually used as a stiffness-changeable spring in the semi-active vibration absorber.In order to get perfect vibration control effect,low dynamic damping of MRE is need.But the dynamic damping of MRE was not studied deeply in the past.The dynamic damping of MRE was studied and analyzed.The influences of different test conditions including test strain amplitude,test frequency and test magnetic field were deeply studied.MRE sample and pure silicone rubber sample were prepared and tested under different conditions.The test results show that the main source of dynamic damping is the friction between iron particles and rubber matrix.And the friction is mainly influenced by the strain amplitude and test magnetic field.

  17. Materials with complex behaviour II properties, non-classical materials and new technologies

    CERN Document Server

    Oechsner, Andreas

    2012-01-01

    This book reviews developments and trends in advanced materials and their properties; modeling and simulation of non-classical materials and new technologies for joining materials. Offers tools for characterizing and predicting properties and behavior.

  18. Dynamic Property of Aluminum Foam

    Directory of Open Access Journals (Sweden)

    S Irie

    2016-09-01

    Full Text Available Aluminum in the foam of metallic foam is in the early stage of industrialization. It has various beneficial characteristics such as being lightweight, heat resistance, and an electromagnetic radiation shield. Therefore, the use of aluminum foam is expected to reduce the weight of equipment for transportation such as the car, trains, and aircraft. The use as energy absorption material is examined. Moreover aluminum foam can absorb the shock wave, and decrease the shock of the blast. Many researchers have reported about aluminum foam, but only a little information is available for high strain rates (103 s-1 or more. Therefore, the aluminum foam at high strain rates hasn't been not characterized yet. The purpose in this research is to evaluate the behavior of the aluminum form in the high-strain rate. In this paper, the collision test on high strain rate of the aluminum foam is investigated. After experiment, the numerical analysis model will be made. In this experiment, a powder gun was used to generate the high strain rate in aluminum foam. In-situ PVDF gauges were used for measuring pressure and the length of effectiveness that acts on the aluminum foam. The aluminum foam was accelerated to about 400 m/s from deflagration of single component powder and the foam were made to collide with the PVDF gauge. The high strain rate deformation of the aluminum form was measured at two collision speeds. As for the result, pressure was observed to go up rapidly when about 70% was compressed. From this result, it is understood that complete crush of the cell is caused when the relative volume is about 70%. In the next stage, this data will be compared with the numerical analysis.

  19. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    1996-01-01

    Fundamentals of Semiconductors attempts to fill the gap between a general solid-state physics textbook and research articles by providing detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors The approach is physical and intuitive rather than formal and pedantic Theories are presented to explain experimental results This textbook has been written with both students and researchers in mind Its emphasis is on understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors The explanations are based on physical insights Each chapter is enriched by an extensive collection of tables of material parameters, figures and problems Many of these problems 'lead the student by the hand' to arrive at the results

  20. Fundamentals of semiconductors physics and materials properties

    CERN Document Server

    Yu, Peter Y

    2010-01-01

    This fourth edition of the well-established Fundamentals of Semiconductors serves to fill the gap between a general solid-state physics textbook and research articles by providing detailed explanations of the electronic, vibrational, transport, and optical properties of semiconductors. The approach is physical and intuitive rather than formal and pedantic. Theories are presented to explain experimental results. This textbook has been written with both students and researchers in mind. Its emphasis is on understanding the physical properties of Si and similar tetrahedrally coordinated semiconductors. The explanations are based on physical insights. Each chapter is enriched by an extensive collection of tables of material parameters, figures, and problems. Many of these problems "lead the student by the hand" to arrive at the results. The major changes made in the fourth edition include: an extensive appendix about the important and by now well-established deep center known as the DX center, additional problems...

  1. Thermal Radiative Properties of Xonotlite Insulation Material

    Institute of Scientific and Technical Information of China (English)

    Xinxin ZHANG; Gaosheng WEI; Fan YU

    2005-01-01

    This paper presents experimental results of thermal radiative properties of xonotlite-type calcium silicate insulation material. Transmittance spectra were first taken using Fourier transform infrared spectrometer (FTIR)for the samples with ρ = 234 kg/m3. Specific extinction coefficient spectra were then obtained by applying Beer's law.Finally,by using the diffusion approximation,the specific Rossland mean extinction coefficients and radiative thermal conductivities were obtained for various temperatures. The results show that the specific spectral extinction coefficient of xonotlite is larger than 7 m2/kg in the whole measured spectra, and diffusion approximation equation is a reasonable description of radiative heat transfer in xonotlite insulation material. The specific Rossland mean extinction coefficient of xonotlite has a maximum ualue at 400 K and the radiative thermal conductivity is almost proportional to the cube of temperature.

  2. Material properties of the plantar aponeurosis.

    Science.gov (United States)

    Kitaoka, H B; Luo, Z P; Growney, E S; Berglund, L J; An, K N

    1994-10-01

    Material properties of the plantar aponeurosis were determined by a two-dimensional video tracking method to simultaneously measure the aponeurosis deformation. Failure loads averaged 1189 +/- 244 N and were higher in men. Average stiffness of the intact fascia was 203.7 +/- 50.5 N/mm at a loading rate of 11.12 N/sec and it did not vary significantly for the loading rates of 11.12 to 1112 N/sec. The high tensile loads required for failure were consistent with clinical and biomechanical studies and indicated the importance of the aponeurosis in foot function and arch stability.

  3. Canopy Dynamics in Nanoscale Ionic Materials

    KAUST Repository

    Jespersen, Michael L.

    2010-07-27

    Nanoscale ionic materials (NIMS) are organic - inorganic hybrids in which a core nanostructure is functionalized with a covalently attached corona and an ionically tethered organic canopy. NIMS are engineered to be liquids under ambient conditions in the absence of solvent and are of interest for a variety of applications. We have used nuclear magnetic resonance (NMR) relaxation and pulse-field gradient (PFG) diffusion experiments to measure the canopy dynamics of NIMS prepared from 18-nm silica cores modified by an alkylsilane monolayer possessing terminal sulfonic acid functionality, paired with an amine-terminated ethylene oxide/propylene oxide block copolymer canopy. Carbon NMR studies show that the block copolymer canopy is mobile both in the bulk and in the NIMS and that the fast (ns) dynamics are insensitive to the presence of the silica nanoparticles. Canopy diffusion in the NIMS is slowed relative to the neat canopy, but not to the degree predicted from the diffusion of hard-sphere particles. Canopy diffusion is not restricted to the surface of the nanoparticles and shows unexpected behavior upon addition of excess canopy. Taken together, these data indicate that the liquid-like behavior in NIMS is due to rapid exchange of the block copolymer canopy between the ionically modified nanoparticles. © 2010 American Chemical Society.

  4. Dynamic properties of ultraviolet-exposed polyurea

    Science.gov (United States)

    Youssef, George; Whitten, Ian

    2016-11-01

    Polyurea is used in military and civilian applications, where exposure to the sun in long durations is imminent. Extended exposure to ultraviolet radiation from the sun can deteriorate its mechanical performance to suboptimal levels. This study reports on the dynamic mechanical properties of polyurea as a function of ultraviolet radiation exposure duration. Six sets of samples were continuously exposed to ultraviolet radiation for different durations up to 18 weeks. Control samples were also tested that did not receive ultraviolet exposure. The dynamic properties were measured using a dynamic mechanical analyzer. Exposed samples exhibited significant color changes from transparent yellow to opaque tan after 18 weeks of exposure. Changes of color were observed as early as 3 weeks of exposure. The dynamic properties showed an initial increase in the dynamic modulus after 3 weeks of exposure, with no further significant change in the stiffness thereafter. The ultraviolet exposure had a significant impact at relatively short loading times or low temperature, for example, up to 6 decades of time. As loading time increases or polyurea operates at high temperature, the effect of ultraviolet exposure and temperature on the performance become highly coupled.

  5. Rheological behavior and dynamic mechanical properties of nano-copper powder/PP composite material%纳米铜粉/PP复合材料的流变性能及动态力学性能研究

    Institute of Scientific and Technical Information of China (English)

    徐德增; 赵婷; 刘智超; 白麓楠; 郭静

    2012-01-01

    将纳米铜粉经硅烷偶联剂KH550处理后,按不同的配比与聚丙烯(PP)混合,经螺杆挤压制得纳米铜粉/PP复合材料,研究了纳米铜粉在PP复合材料中的分散性以及PP复合材料的流变性能和动态力学性能.结果表明:经改性后的纳米铜粉均匀分散在PP中;纳米铜粉/PP复合材料为非牛顿假塑性流体;在低剪切速率下,复合材料熔体的黏度高于纯PP的,随着纳米铜粉的含量增加,复合材料体系的表观黏度增大,高剪切速率时,纳米铜粉的添加量对复合材料的流动性能影响较小;当复合材料体系中纳米铜粉的质量分数小于或等于0.5%时,其熔体流动性能提高,储能模量小于纯PP的,当纳米铜粉质量分数大于0.5%时,其储能模量提高并高于纯PP的.%Nano-copper powder/polypropylene (PP) composite material was prepared by blending PP and nano-copper powder modified with silane coupling agent KH550 at different ratios prior to screw extrusion. The dispersion of nano-copper powder in PP composite material was studied, as were the rheological behavior and dynamic mechanical properties of PP composite material. The results showed that nano-copper powder uniformly dispersed in PP matrix after modification; nano-copper powder/PP composite material was non-Newtonian pseudoplastic fluid; the viscosity of the composite material melt was higher than that of pure PP at low shearing rate; the apparent viscosity of the composite material system was increased with the addition of nano-copper powder; the addition of nano-copper powder had a slight effect on the rheological behavior of composite material at high shearing rate; the flowability of the composite material melt was improved, the storage modulus was lower than that of pure PP when the addition of nano-copper powder was not more than 0. 5% by mass fraction in the composite material system; and the storage modulus was higher than that of pure PP when the mass fraction of nano

  6. Mechanical Properties of Heat Exchanger Tube Materials at Elevated Temperatures

    Science.gov (United States)

    Kahl, Sören; Zajac, Jozefa; Ekström, Hans-Erik

    Since automotive heat exchangers are operated at elevated temperatures and under varying pressures, both static and dynamic mechanical properties should be known at the relevant temperatures. We have collected elevated-temperature tensile test data, elevated-temperature stress amplitude-fatigue life data, and creep-rupture data in a systematic fashion over the past years. For thin, soft, and braze-simulated heat exchanger tube materials tested inside closed furnaces, none of the well-established methods for crack detection and observation can be applied. In our contribution, we present a simple statistical method to estimate the time required for crack initiation.

  7. Experimental Study on the Comparison of the Material Properties of Glass Wool Used as Building Materials

    Directory of Open Access Journals (Sweden)

    Kyoung-Woo KIM

    2014-04-01

    Full Text Available Artificial mineral fibers such as glass wool or stone wool are commonly used in building walls, ceilings and floors as a major insulation material for buildings. Among the material properties of building materials, thermal conductivity, the sound absorption coefficient, compressibility, and dynamic stiffness are regarded as important performance requirements since they directly affect the thermal and acoustic properties of the building. This study measured the changes of the thermal and acoustical performances of glass wool that was actually installed for a long time to the outer wall of a building as an insulation material through a comparison with recently produced glass wool. The results showed that the measured thermal conductivities of the old and the new specimens both rise with an increase of temperature, showing quite similar results in both specimens over temperature ranges of (0 – 20 ºC. The noise reduction coefficient decreased by 0.1 in the old specimen and the difference of the compressibilities in both specimens was shown to be 7.32 mm. The dynamic stiffness of the old specimen was found to be 1.28 MN/m3 higher than that of the new specimen.DOI: http://dx.doi.org/10.5755/j01.ms.20.1.3714

  8. Quasimolecular Dynamic Simulation for Bending Fracture of Laminar Composite Materials

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Recently, quasimolecular dynamics has been successfully used to simulate the deformation characteristics of actual size solid materials. In quasimolecular dynamics, which is an attempt to bridge the gap between atomistic and continuum simulations, molecules are aggregated into large units, called quasimolecules, to evaluate large scale material behavior. In this paper, a 2-dimensional numerical simulation using quasimolecular dynamics was performed to investigate laminar composite material fractures and crack propagation behavior in the uniform bending of laminar composite materials. It was verified that under bending deformation laminar composite materials deform quite differently from homogeneous materials

  9. Dynamic fracture of functionally graded magnetoelectroelastic composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Stoynov, Y. [Faculty of Applied Mathematics and Informatics, Technical University of Sofia (Bulgaria); Dineva, P. [Institute of Mechanics, Bulgarian Academy of Sciences, Sofia (Bulgaria)

    2014-11-12

    The stress, magnetic and electric field analysis of multifunctional composites, weakened by impermeable cracks, is of fundamental importance for their structural integrity and reliable service performance. The aim is to study dynamic behavior of a plane of functionally graded magnetoelectroelastic composite with more than one crack. The coupled material properties vary exponentially in an arbitrary direction. The plane is subjected to anti-plane mechanical and in-plane electric and magnetic load. The boundary value problem described by the partial differential equations with variable coefficients is reduced to a non-hypersingular traction boundary integral equation based on the appropriate functional transform and frequency-dependent fundamental solution derived in a closed form by Radon transform. Software code based on the boundary integral equation method (BIEM) is developed, validated and inserted in numerical simulations. The obtained results show the sensitivity of the dynamic stress, magnetic and electric field concentration in the cracked plane to the type and characteristics of the dynamic load, to the location and cracks disposition, to the wave-crack-crack interactions and to the magnitude and direction of the material gradient.

  10. Sorting cells by their dynamical properties

    Science.gov (United States)

    Henry, Ewan; Holm, Stefan H.; Zhang, Zunmin; Beech, Jason P.; Tegenfeldt, Jonas O.; Fedosov, Dmitry A.; Gompper, Gerhard

    2016-10-01

    Recent advances in cell sorting aim at the development of novel methods that are sensitive to various mechanical properties of cells. Microfluidic technologies have a great potential for cell sorting; however, the design of many micro-devices is based on theories developed for rigid spherical particles with size as a separation parameter. Clearly, most bioparticles are non-spherical and deformable and therefore exhibit a much more intricate behavior in fluid flow than rigid spheres. Here, we demonstrate the use of cells’ mechanical and dynamical properties as biomarkers for separation by employing a combination of mesoscale hydrodynamic simulations and microfluidic experiments. The dynamic behavior of red blood cells (RBCs) within deterministic lateral displacement (DLD) devices is investigated for different device geometries and viscosity contrasts between the intra-cellular fluid and suspending medium. We find that the viscosity contrast and associated cell dynamics clearly determine the RBC trajectory through a DLD device. Simulation results compare well to experiments and provide new insights into the physical mechanisms which govern the sorting of non-spherical and deformable cells in DLD devices. Finally, we discuss the implications of cell dynamics for sorting schemes based on properties other than cell size, such as mechanics and morphology.

  11. Dynamic properties of three-dimensional piezoelectric Kagome grids

    Science.gov (United States)

    Wu, Zhi-Jing; Li, Feng-Ming

    2015-07-01

    Piezoelectric Kagome grids can be considered as a kind of functional material because they have vibration isolation performance and can transform mechanical energy to electric energy. In this study, the dynamic properties of three-dimensional (3D) piezoelectric Kagome grids without and with material defects are studied based on the frequency-domain responses. The spectral element method (SEM) is adopted to solve a 3D piezoelectric beam which contains bending components in two planes, tensional components, and torsional components. The dynamic stiffness matrix of a spectral piezoelectric beam is derived. Highly accurate solutions in the frequency-domain are obtained by solving the equation of motion of the whole structure. Compared with the results from the FEM and those in the existing literature, it can be seen that the SEM can be effectively used to study the 3D piezoelectric Kagome grids. The band-gap properties of Kagome grid and defect state properties of Kagome grid with material defects are analyzed. The effect of the piezoelectric parameter on the band-gap property is investigated further.

  12. Structure and dynamics in network-forming materials

    Science.gov (United States)

    Wilson, Mark

    2016-12-01

    The study of the structure and dynamics of network-forming materials is reviewed. Experimental techniques used to extract key structural information are briefly considered. Strategies for building simulation models, based on both targeting key (experimentally-accessible) materials and on systematically controlling key model parameters, are discussed. As an example of the first class of materials, a key target system, SiO2, is used to highlight how the changing structure with applied pressure can be effectively modelled (in three dimensions) and used to link to both experimental results and simple structural models. As an example of the second class the topology of networks of tetrahedra in the MX2 stoichiometry are controlled using a single model parameter linked to the M-X-M bond angles. The evolution of ordering on multiple length-scales is observed as are the links between the static structure and key dynamical properties. The isomorphous relationship between the structures of amorphous Si and SiO2 is discussed as are the similarities and differences in the phase diagrams, the latter linked to potential polyamorphic and ‘anomalous’ (e.g. density maxima) behaviour. Links to both two-dimensional structures for C, Si and Ge and near-two-dimensional bilayers of SiO2 are discussed. Emerging low-dimensional structures in low temperature molten carbonates are also uncovered.

  13. Non-Adiabatic Molecular Dynamics Methods for Materials Discovery

    Energy Technology Data Exchange (ETDEWEB)

    Furche, Filipp [Univ. of California, Irvine, CA (United States); Parker, Shane M. [Univ. of California, Irvine, CA (United States); Muuronen, Mikko J. [Univ. of California, Irvine, CA (United States); Roy, Saswata [Univ. of California, Irvine, CA (United States)

    2017-04-04

    The flow of radiative energy in light-driven materials such as photosensitizer dyes or photocatalysts is governed by non-adiabatic transitions between electronic states and cannot be described within the Born-Oppenheimer approximation commonly used in electronic structure theory. The non-adiabatic molecular dynamics (NAMD) methods based on Tully surface hopping and time-dependent density functional theory developed in this project have greatly extended the range of molecular materials that can be tackled by NAMD simulations. New algorithms to compute molecular excited state and response properties efficiently were developed. Fundamental limitations of common non-linear response methods were discovered and characterized. Methods for accurate computations of vibronic spectra of materials such as black absorbers were developed and applied. It was shown that open-shell TDDFT methods capture bond breaking in NAMD simulations, a longstanding challenge for single-reference molecular dynamics simulations. The methods developed in this project were applied to study the photodissociation of acetaldehyde and revealed that non-adiabatic effects are experimentally observable in fragment kinetic energy distributions. Finally, the project enabled the first detailed NAMD simulations of photocatalytic water oxidation by titania nanoclusters, uncovering the mechanism of this fundamentally important reaction for fuel generation and storage.

  14. Dynamical properties of the Rabi model

    Science.gov (United States)

    Hu, Binglu; Zhou, Huili; Chen, Shujie; Xianlong, Gao; Wang, Kelin

    2017-02-01

    We study the dynamical properties of the quantum Rabi model using a systematic expansion method. Based on the observation that the parity symmetry of the Rabi model is kept during evolution of the states, we decompose the initial state and the time-dependent one into positive and negative parity parts expanded by superposition of the coherent states. The evolutions of the corresponding positive and the negative parities are obtained, in which the expansion coefficients in the dynamical equations are known from the derived recurrence relation.

  15. The Electrical and Dynamical Properties of Biomembranes

    DEFF Research Database (Denmark)

    Mosgaard, Lars Dalskov

    of a more general treatment. This purely thermodynamical treatment only describes the equilibrium properties of the membrane, however biological processes are of course dynamical in nature. A clear understanding of the dynamical behavior of lipid membranes is therefore essential when we aim at unraveling...... electrophysiological methods such as \\jump experiments" and impedance spectroscopy performed on lipid membranes. By doing so we observe that a number of non-linear phenomena previously thought to be associated with the presence of proteins embedded in the membrane can just as well be produced by a 'pure' lipid...

  16. Interdisciplinary research on the nature and properties of ceramic materials

    Science.gov (United States)

    1980-01-01

    The advancement of material performance and design methodology as related to brittle materials was investigated. The processing and properties of ceramic materials as related to design requirements was also studied.

  17. Thermophysical Properties of Selected Aerospace Materials. Part 2. Thermophysical Properties of Seven Materials

    Science.gov (United States)

    1977-01-01

    Determining Thermal Conductivity of Solids from 20 to 600 K," Cryogenics, 5( 1), 17-20, 1965. 11. Garth, R.C. and Sailer , V.L., "Thermal Conductivity of...34Thermal Property Data Utilized for Asset Materials," McDonnell Aircraft Corp. Rept. A656, 45 pp., 1964. [AD 480 414] 23. Makarounls, O., " Solar

  18. Properties of Sealing Materials in Groundwater Wells

    DEFF Research Database (Denmark)

    Köser, Claus

    on the maximum swelling pressure; i) the bulk density of the sample, and ii) whether the sample is sorted or unsorted. CT scans (Computed Tomography) have been used to evaluate certain properties of bentonite seals in a limited volume. In this context, a set of algorithms to convert CT numbers (HU unit......) into densities for clay/water systems has been developed. This method has successfully been used to evaluate e.g., macroporosity, homogenization of the bentonite seal during the hydration of water, hydraulic conductivity and the creation of channels in the bentonite seals. Based on the results obtained...... in this Ph.D. thesis, a number of recommendations has been offered; i) a change regarding the production of pellets and ii) how sealing material must be treated in the actual construction of groundwater wells....

  19. Bone Material Properties in Osteogenesis Imperfecta.

    Science.gov (United States)

    Bishop, Nick

    2016-04-01

    Osteogenesis imperfecta entrains changes at every level in bone tissue, from the disorganization of the collagen molecules and mineral platelets within and between collagen fibrils to the macroarchitecture of the whole skeleton. Investigations using an array of sophisticated instruments at multiple scale levels have now determined many aspects of the effect of the disease on the material properties of bone tissue. The brittle nature of bone in osteogenesis imperfecta reflects both increased bone mineralization density-the quantity of mineral in relation to the quantity of matrix within a specific bone volume-and altered matrix-matrix and matrix mineral interactions. Contributions to fracture resistance at multiple scale lengths are discussed, comparing normal and brittle bone. Integrating the available information provides both a better understanding of the effect of current approaches to treatment-largely improved architecture and possibly some macroscale toughening-and indicates potential opportunities for alternative strategies that can influence fracture resistance at longer-length scales.

  20. Spacecraft dielectric material properties and spacecraft charging

    Science.gov (United States)

    Frederickson, A. R.; Wall, J. A.; Cotts, D. B.; Bouquet, F. L.

    1986-01-01

    The physics of spacecraft charging is reviewed, and criteria for selecting and testing semiinsulating polymers (SIPs) to avoid charging are discussed and illustrated. Chapters are devoted to the required properties of dielectric materials, the charging process, discharge-pulse phenomena, design for minimum pulse size, design to prevent pulses, conduction in polymers, evaluation of SIPs that might prevent spacecraft charging, and the general response of dielectrics to space radiation. SIPs characterized include polyimides, fluorocarbons, thermoplastic polyesters, poly(alkanes), vinyl polymers and acrylates, polymers containing phthalocyanine, polyacene quinones, coordination polymers containing metal ions, conjugated-backbone polymers, and 'metallic' conducting polymers. Tables summarizing the results of SIP radiation tests (such as those performed for the NASA Galileo Project) are included.

  1. Dynamic thermo-mechanical properties of various flowable resin composites

    Science.gov (United States)

    Balthazard, Rémy; Vincent, Marin; Dahoun, Abdessellam; Mortier, Eric

    2016-01-01

    Background This study compared the storage modulus (E’), the loss modulus (E’’) and the loss tangent (tan δ) of various flowable resin composites. Material and Methods Grandio Flow (GRF), GrandioSo Heavy Flow (GHF), Filtek Supreme XTE (XTE) and Filtek Bulk Fill (BUL) flowable resins and Clinpro Sealant (CLI) ultra-flowable pit and fissure sealant resin were used. 25 samples were tested using a dynamical mechanical thermal analysis system in bending mode. Measurements were taken within a temperature range of 10 to 55°C. The results were statistically analyzed using mixed-effect and repeated-measure analysis of variance followed by paired multiple comparisons. Results For all the materials, the E’ values decrease with temperature, whereas the tan δ values increase. Irrespective of the temperature, GHF and GRF present E’ and E’’ values significantly higher than all the other materials and CLI presents values significantly lower than all the other materials. Observation of the values for all the materials reveals a linear progression of the tan δ values with temperature. Conclusions A variation in temperature within a physiological range generates modifications in mechanical properties without damaging the material, however. Filler content in volume terms appears to be the crucial parameter in the mechanical behavior of tested materials. Key words:Dynamic mechanical thermal analysis, elastic modulus, filler content, flowable resin composites, loss modulus, loss tangent. PMID:27957266

  2. Estimation of hygroscopic power of electrotechnical materials by dynamic speckle technique

    Science.gov (United States)

    Bertolini, G.; Cabello, C. I.; Arizaga, R.; Trivi, M.; Barbera, Gustavo

    2013-11-01

    Dynamic speckle laser (DLS) technique has been applied to the analysis of different biological systems, inorganic materials and industrial processes. In this paper, we use this technique to analyze the hygroscopic properties of different types of porcelain and papers for electrotechnical purposes. Experimental speckle results showed different behavior depending on physicochemical and textural properties of the samples.

  3. Multifractal properties of ball milling dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Budroni, M. A., E-mail: mabudroni@uniss.it; Pilosu, V.; Rustici, M. [Dipartimento di Chimica e Farmacia, Università degli Studi di Sassari, Via Vienna 2, Sassari 07100 (Italy); Delogu, F. [Dipartimento di Ingegneria Meccanica, Chimica, e dei Materiali, Università degli Studi di Cagliari, via Marengo 2, Cagliari 09123 (Italy)

    2014-06-15

    This work focuses on the dynamics of a ball inside the reactor of a ball mill. We show that the distribution of collisions at the reactor walls exhibits multifractal properties in a wide region of the parameter space defining the geometrical characteristics of the reactor and the collision elasticity. This feature points to the presence of restricted self-organized zones of the reactor walls where the ball preferentially collides and the mechanical energy is mainly dissipated.

  4. Multifractal properties of ball milling dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Budroni, M. A., E-mail: mabudroni@uniss.it; Pilosu, V.; Rustici, M. [Dipartimento di Chimica e Farmacia, Università degli Studi di Sassari, Via Vienna 2, Sassari 07100 (Italy); Delogu, F. [Dipartimento di Ingegneria Meccanica, Chimica, e dei Materiali, Università degli Studi di Cagliari, via Marengo 2, Cagliari 09123 (Italy)

    2014-06-15

    This work focuses on the dynamics of a ball inside the reactor of a ball mill. We show that the distribution of collisions at the reactor walls exhibits multifractal properties in a wide region of the parameter space defining the geometrical characteristics of the reactor and the collision elasticity. This feature points to the presence of restricted self-organized zones of the reactor walls where the ball preferentially collides and the mechanical energy is mainly dissipated.

  5. Mechanical properties of low dimensional materials

    Science.gov (United States)

    Saini, Deepika

    Recent advances in low dimensional materials (LDMs) have paved the way for unprecedented technological advancements. The drive to reduce the dimensions of electronics has compelled researchers to devise newer techniques to not only synthesize novel materials, but also tailor their properties. Although micro and nanomaterials have shown phenomenal electronic properties, their mechanical robustness and a thorough understanding of their structure-property relationship are critical for their use in practical applications. However, the challenges in probing these mechanical properties dramatically increase as their dimensions shrink, rendering the commonly used techniques inadequate. This dissertation focuses on developing techniques for accurate determination of elastic modulus of LDMs and their mechanical responses under tensile and shear stresses. Fibers with micron-sized diameters continuously undergo tensile and shear deformations through many phases of their processing and applications. Significant attention has been given to their tensile response and their structure-tensile properties relations are well understood, but the same cannot be said about their shear responses or the structure-shear properties. This is partly due to the lack of appropriate instruments that are capable of performing direct shear measurements. In an attempt to fill this void, this dissertation describes the design of an inexpensive tabletop instrument, referred to as the twister, which can measure the shear modulus (G) and other longitudinal shear properties of micron-sized individual fibers. An automated system applies a pre-determined twist to the fiber sample and measures the resulting torque using a sensitive optical detector. The accuracy of the instrument was verified by measuring G for high purity copper and tungsten fibers. Two industrially important fibers, IM7 carbon fiber and KevlarRTM 119, were found to have G = 17 and 2.4 GPa, respectively. In addition to measuring the shear

  6. The effects of the size of nanocrystalline materials on their thermodynamic and mechanical properties.

    Science.gov (United States)

    Yu, Xiaohua; Zhan, Zhaolin

    2014-01-01

    This work has considered the intrinsic influence of bond energy on the macroscopic, thermodynamic, and mechanical properties of crystalline materials. A general criterion is proposed to evaluate the properties of nanocrystalline materials. The interrelation between the thermodynamic and mechanical properties of nanomaterials is presented and the relationship between the variation of these properties and the size of the nanomaterials is explained. The results of our work agree well with thermodynamics, molecular dynamics simulations, and experimental results. This method is of significance in investigating the size effects of nanomaterials and provides a new approach for studying their thermodynamic and mechanical properties.

  7. Novel thermal properties of nanostructured materials.

    Energy Technology Data Exchange (ETDEWEB)

    Eastman, J. A.

    1999-01-13

    A new class of heat transfer fluids, termed nanofluids, has been developed by suspending nanocrystalline particles in liquids. Due to the orders-of-magnitude larger thermal conductivities of solids compared to those of liquids such as water, significantly enhanced thermal properties are obtained with nanofluids. For example, an approximately 20% improvement in effective thermal conductivity is observed when 5 vol.% CuO nanoparticles are added to water. Even more importantly, the heat transfer coefficient of water under dynamic flow conditions is increased more than 15% with the addition of less than 1 vol.% CuO particles. The use of nanofluids could impact many industrial sectors, including transportation, energy supply and production, electronics, textiles, and paper production by, for example, decreasing pumping power needs or reducing heat exchanger sizes. In contrast to the enhancement in effective thermal transport rates that is obtained when nanoparticles are suspended in fluids, nanocrystalline coatings are expected to exhibit reduced thermal conductivities compared to coarse-grained coatings. Reduced thermal conductivities are predicted to arise because of a reduction in the mean free path of phonons due to presence of grain boundaries. This behavior, combined with improved mechanical properties, makes nanostructured zirconia coatings excellent candidates for future applications as thermal barriers. Yttria-stabilized zirconia (YSZ) thin films are being produced by metal-organic chemical vapor deposition techniques. Preliminary results have indicated that the thermal conductivity is reduced by approximately a factor-of-two at room temperature in 10 nm grain-sized YSZ compared to coarse-grained or single crystal YSZ.

  8. Measurement of Mechanical Properties of Cantilever Shaped Materials

    Directory of Open Access Journals (Sweden)

    Thomas Thundat

    2008-05-01

    variations. When appropriate, we use continuum mechanics, which is justified according to the ratio between the cantilever thickness and the grain size of the materials. We will also address other potential applications such as the ageing process of nuclear materials, building materials, and optical fibers, which can be investigated by monitoring their mechanical changes with time. In summary, by virtue of the dynamic response of a miniaturized cantilever shaped material, we present useful measurements of the associated elastic properties.

  9. Gas bubble dynamics in soft materials.

    Science.gov (United States)

    Solano-Altamirano, J M; Malcolm, John D; Goldman, Saul

    2015-01-01

    Epstein and Plesset's seminal work on the rate of gas bubble dissolution and growth in a simple liquid is generalized to render it applicable to a gas bubble embedded in a soft elastic solid. Both the underlying diffusion equation and the expression for the gas bubble pressure were modified to allow for the non-zero shear modulus of the medium. The extension of the diffusion equation results in a trivial shift (by an additive constant) in the value of the diffusion coefficient, and does not change the form of the rate equations. But the use of a generalized Young-Laplace equation for the bubble pressure resulted in significant differences on the dynamics of bubble dissolution and growth, relative to an inviscid liquid medium. Depending on whether the salient parameters (solute concentration, initial bubble radius, surface tension, and shear modulus) lead to bubble growth or dissolution, the effect of allowing for a non-zero shear modulus in the generalized Young-Laplace equation is to speed up the rate of bubble growth, or to reduce the rate of bubble dissolution, respectively. The relation to previous work on visco-elastic materials is discussed, as is the connection of this work to the problem of Decompression Sickness (specifically, "the bends"). Examples of tissues to which our expressions can be applied are provided. Also, a new phenomenon is predicted whereby, for some parameter values, a bubble can be metastable and persist for long times, or it may grow, when embedded in a homogeneous under-saturated soft elastic medium.

  10. Striking dynamics and kinetic properties of boxing and MMA gloves

    Directory of Open Access Journals (Sweden)

    Benjamin Lee

    2014-08-01

    Full Text Available With the growing popularity of Mixed Martial Arts (MMA as a competitive sport, questions regarding the dynamic response and properties of MMA gloves arise. High-energy impacts from punches are very similar to boxing yet MMA competition requires the use of 4 oz fingerless glove, compared to the larger full enclosure boxing glove. This work assessed the kinetic properties and strike dynamics of MMA gloves and compared findings with traditional boxing gloves. Gloves mounted on a molded fist were impacted repetitively on an instrumental anvil designed for impact, over a 5 hour period resulting in 10,000 continuous and consistent strikes. Kinetic data from impacts were sampled at the beginning of the data collection and subsequently every 30 minutes (every 1,000 strikes. MMA gloves produced 4-5 times greater peak force and 5 times faster load rate compared to the boxing glove. However, MMA gloves also showed signs of material fatigue, with peak force increasing by 35% and rate of loading increasing by 60% over the duration of the test. Boxing glove characteristics did deteriorate but to a lesser extent. In summary, the kinetic properties of MMA glove differed substantially from the boxing glove resulting in impacts characterized by higher peak forces and more rapid development of force. Material properties including stiffness and thickness play a role in the kinetic characteristics upon impact, and can be inferred to alter injury mechanisms of blunt force trauma.

  11. Comparison of static and dynamic properties in a shale rock

    Science.gov (United States)

    Bonnelye, Audrey; Pimienta, Lucas; Schubnel, Alexandre; David, Christian

    2017-04-01

    When trying to understand the elastic properties of rocks in order to ultimately compare laboratory and field data, two opposite measuring techniques can be used: the "static" and "dynamic" measurement techniques. The "static" measurement technique consists in characterising the medium by its strain response to an applied stress. The strain rate is generally low enough that the measurement can be addressed as static. Using ultrasonic wave velocity, the "dynamic" measurements are obtained. Those allow obtaining accurately the full set of elastic constants characterising the medium. However, such measuring procedure is at high frequency, implying the risk for dispersion and attenuation effects to occur. When comparing the "static" and "dynamic" measurements, and investigating their differences, the effect of the measuring frequency is often the parameter considered. However, it is not the only parameter that may play a role. Indeed, often, "static" measurements rely on strain amplitudes above 10-4. On the other hand, "dynamic" measurements rely on strain amplitudes below 10-6. Such difference may play an important role in comparing measurements in weak materials such as shales. For this particular rock, the effect of strain amplitude on the "static" measurements is investigated by decreasing the amplitude of stress variations. Moreover, due to both multiscale and sedimentary nature, shale materials can exhibit strong anisotropic properties, usually described as transversly isotropic. In this study we propose to compare the different ways of measuring elastic moduli of Tournemire shale (IRSN underground laboratory, Aveyron, Southern France). In a first part, static moduli were calculated on three sets of samples with different bedding orientations (90°, 0°, 45°) deformed under deviatoric pressure at different confining pressures (2.5, 5, 10, 20, 40, 80MPa). During these deformation experiments, elastic wave velocities were continuously measured along different

  12. A dynamic network in a dynamic population: asymptotic properties

    CERN Document Server

    Britton, Tom; Turova, Tatyana

    2011-01-01

    We derive asymptotic properties for a stochastic dynamic network model in a stochastic dynamic population. In the model, nodes give birth to new nodes until they die, each node being equipped with a social index given at birth. During the life of a node it creates edges to other nodes, nodes with high social index at higher rate, and edges disappear randomly in time. For this model we derive criterion for when a giant connected component exists after the process has evolved for a long period of time, assuming the node population grows to infinity. We also obtain an explicit expression for the degree correlation $\\rho$ (of neighbouring nodes) which shows that $\\rho$ is always positive irrespective of parameter values in one of the two treated submodels, and may be either positive or negative in the other model, depending on the parameters.

  13. Calculation of the dynamic air flow resistivity of fibre materials

    DEFF Research Database (Denmark)

    Tarnow, Viggo

    1997-01-01

    The acoustic attenuation of acoustic fiber materials is mainly determined by the dynamic resistivity to an oscillating air flow. The dynamic resistance is calculated for a model with geometry close to the geometry of real fibre material. The model constists of parallel cylinders placed randomly. ......-consistent procedure gives the same results as the more complicated procedure based on average over Voronoi cells. Graphs of the dynamic resistivity versus frequency are given for fiber densities and diameters typical for acoustic fiber materials.......The acoustic attenuation of acoustic fiber materials is mainly determined by the dynamic resistivity to an oscillating air flow. The dynamic resistance is calculated for a model with geometry close to the geometry of real fibre material. The model constists of parallel cylinders placed randomly...

  14. Dynamic Mechanical Properties of Bio-Polymer Graphite Thin Films

    Science.gov (United States)

    Saddam Kamarudin, M.; Rus, Anika Zafiah M.; Munirah Abdullah, Nur; Abdullah, M. F. L.

    2017-08-01

    Waste cooking oil is used as the main substances in producing graphite biopolymer thin films. Biopolymer is produce from the reaction of bio-monomer and cross linker with the ratio of 2:1 and addition of graphite with an increment of 2% through a slip casting method. The morphological surface properties of the samples are observed by using Scanning Electron Microscope (SEM). It is shown that the graphite particle is well mixed and homogenously dispersed in biopolymer matrix. Meanwhile, the mechanical response of materials by monitoring the change in the material properties in terms of frequency and temperature of the samples were determined using Dynamic Mechanical Analysis (DMA). The calculated cross-linked density of biopolymer composites revealed the increment of graphite particle loading at 8% gives highest results with 260.012 x 103 M/m3.

  15. Transition metal chalcogenides: ultrathin inorganic materials with tunable electronic properties.

    Science.gov (United States)

    Heine, Thomas

    2015-01-20

    presence of an external electric field are reported. While all materials of the MoWSeS family share the same qualitative properties, their individual values can differ strongly, for example, the spin-orbit splitting in WSe2 reaches the value of 428 meV, nearly three times that of MoS2. Further, we discuss the effect of strain on the electronic properties (straintronics). While MoWSeS single layers are very robust against external electric fields, bilayers show a linear reduction of the band gap, even reaching a semiconductor-metal phase transition, and an increase of the spin-orbit splitting from zero to the monolayer value at rather small fields. Strain is yet another possibility to control the band gap in a linear way, and MoWSeS monolayers become metallic at strain values of ∼10%. The density-functional based tight-binding model is a useful tool to investigate the electronic and structural properties, including electron conductance, of large MoS2 structures, which show spontaneous rippling in finite-temperature molecular dynamics simulations. Structural defects in MoS2 result in anisotropy of the electric conductivity. Finally, DFT predictions on the properties of noble metal dichalcogenides are presented. Most strikingly, 1T PdS2 is an indirect band gap semiconductor in its monolayer form but becomes metallic as a bilayer.

  16. Structural and dynamical properties of complex networks

    Science.gov (United States)

    Ghoshal, Gourab

    Recent years have witnessed a substantial amount of interest within the physics community in the properties of networks. Techniques from statistical physics coupled with the widespread availability of computing resources have facilitated studies ranging from large scale empirical analysis of the worldwide web, social networks, biological systems, to the development of theoretical models and tools to explore the various properties of these systems. Following these developments, in this dissertation, we present and solve for a diverse set of new problems, investigating the structural and dynamical properties of both model and real world networks. We start by defining a new metric to measure the stability of network structure to disruptions, and then using a combination of theory and simulation study its properties in detail on artificially generated networks; we then compare our results to a selection of networks from the real world and find good agreement in most cases. In the following chapter, we propose a mathematical model that mimics the structure of popular file-sharing websites such as Flickr and CiteULike and demonstrate that many of its properties can solved exactly in the limit of large network size. The remaining part of the dissertation primarily focuses on the dynamical properties of networks. We first formulate a model of a network that evolves under the addition and deletion of vertices and edges, and solve for the equilibrium degree distribution for a variety of cases of interest. We then consider networks whose structure can be manipulated by adjusting the rules by which vertices enter and leave the network. We focus in particular on degree distributions and show that, with some mild constraints, it is possible by a suitable choice of rules to arrange for the network to have any degree distribution we desire. In addition we define a simple local algorithm by which appropriate rules can be implemented in practice. Finally, we conclude our

  17. Dynamical Mechanical Properties for AD90 Alumina

    Institute of Scientific and Technical Information of China (English)

    REN Hui-lan; NING Jian-guo; LI Ping

    2007-01-01

    The dynamic response of polycrystalline alumina was investigated in the pressure range of 0 -13 GPa by planar impact experiments.Velocity interferometer system for any reflector(VISAR) was used to obtain free surface velocity profile and determine the Hugoniot elastic limit,and manganin gauges were employed to obtain the stress-time histories and determine Hugoniot curve.Both the free surface particle velocity profiles and Hugoniot curves indicate the dispersion of the "plastic" wave for alumina.With the measured stress histories,the complete histories of strain,particle velocity,specific volume and specific internal energy are gained by using path line principle of Lagrange analysis.The dynamic mechanical behaviors for alumina under impact loading are analyzed,such as nonlinear characteristic,strain rate dependence,dispersion and declination of shock wave in the material.

  18. Dynamical properties of unconventional magnetic systems

    Energy Technology Data Exchange (ETDEWEB)

    Helgesen, G. [ed.

    1997-05-01

    The Advanced Study Institute addressed the current experimental and theoretical knowledge of the dynamical properties of unconventional magnetic systems including low-dimensional and mesoscopic magnetism, unconventional ground state, quantum magnets and soft matter. The main approach in this Advanced Study Institute was to obtain basic understanding of co-operative phenomena, fluctuations and excitations in the wide range unconventional magnetic systems now being fabricated or envisioned. The report contains abstracts for lectures, invited seminars and posters, together with a list of the 95 participants from 24 countries with e-mail addresses

  19. Dynamic Colour Possibilities and Functional Properties of Thermochromic Printing Inks

    Directory of Open Access Journals (Sweden)

    Rahela Kulcar

    2012-07-01

    Full Text Available Thermochromic printing inks change their colour regarding the change in temperature and they are one of the major groups of colour-changing inks. One of the most frequently used thermochromic material in printing inks are leuco dyes. The colour of thermochromic prints is dynamic, it is not just temperature-dependent, but it also depends on thermal history. The effect is described by colour hysteresis. This paper aims at discussing general aspects of thermochromic inks, dynamic colorimetric properties of leuco dye-based thermochromic inks, their stability and principle of variable-temperature colour measurement. Thermochromic material is protected in round-shaped capsules. They are much larger than pigments in conventional inks. The polymer envelopes of pigment capsules are more stable against oxidation than the binder. If these envelopes are damaged, the dynamic colour is irreversibly lost. Our aim is to analyse the colorimetric properties of several reversible screen-printed UV-curing leuco dye thermochromic inks with different activation temperatures printed on paper. A small analysis of irreversible thermochromic inks will be presented for comparison with reversible thermochromic inks. Moreover, so as to show interesting possibilities, a combination of different inks was made, an irreversible thermochromic ink was printed on top of the red and blue reversible thermochromic inks. Special attention was given to the characterization of colour hysteresis and the meaning of activation temperature.

  20. Dynamic Properties of Fiber Reinforced Cement Mortar

    Institute of Scientific and Technical Information of China (English)

    唐志平; 徐松林; 胡晓军; 廖香丽; 蔡建

    2004-01-01

    Based on the shear wave tracing(SWT) technique proposed by Tang Z P, particle velocity gauge and the dual internal measurement for pressure and shear waves (IMPS) system are applied to investigate the responses of fiber reinforced cement subjected to impact loading. Series of experiments are conducted. The results show that there exist four critical points, A, B, C, D, in p-V Hugoniot curves. They correspond to the Hugoniot elastic limit (HEL) of the material, the critical point for shear strength limit and transition from damage state to failure state, void collapse, and solid compression, respectively. The critical point B is difficult to be aware of and never reported. However, it can be clearly disclosed with SWT method. Based on the analyses of shear strength, it can be concluded that the transversal wave, especially the unloading transversal wave, is especially important for the dynamic damage investigation of brittle materials.

  1. Material properties of the heel fat pad across strain rates.

    Science.gov (United States)

    Grigoriadis, Grigoris; Newell, Nicolas; Carpanen, Diagarajen; Christou, Alexandros; Bull, Anthony M J; Masouros, Spyros D

    2017-01-01

    The complex structural and material behaviour of the human heel fat pad determines the transmission of plantar loading to the lower limb across a wide range of loading scenarios; from locomotion to injurious incidents. The aim of this study was to quantify the hyper-viscoelastic material properties of the human heel fat pad across strains and strain rates. An inverse finite element (FE) optimisation algorithm was developed and used, in conjunction with quasi-static and dynamic tests performed to five cadaveric heel specimens, to derive specimen-specific and mean hyper-viscoelastic material models able to predict accurately the response of the tissue at compressive loading of strain rates up to 150s(-1). The mean behaviour was expressed by the quasi-linear viscoelastic (QLV) material formulation, combining the Yeoh material model (C10=0.1MPa, C30=7MPa, K=2GPa) and Prony׳s terms (A1=0.06, A2=0.77, A3=0.02 for τ1=1ms, τ2=10ms, τ3=10s). These new data help to understand better the functional anatomy and pathophysiology of the foot and ankle, develop biomimetic materials for tissue reconstruction, design of shoe, insole, and foot and ankle orthoses, and improve the predictive ability of computational models of the foot and ankle used to simulate daily activities or predict injuries at high rate injurious incidents such as road traffic accidents and underbody blast. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  2. Structure and properties of layered inorganic materials

    Institute of Scientific and Technical Information of China (English)

    Xue Duan

    2010-01-01

    @@ Inorganic layered materials are a class of advanced functional materials that have attracted considerable attention by virtue of their practical applications in a wide variety of fields. Sys-tematic studies of structure, design, synthesis, and fabrication processing may extend the range of practical utility of inor-ganic layered functional materials, in areas such as food industry,chemical industry, energy engineering, environmental engineer-ing, drug and gene delivery, electronics technology, and materials protection.

  3. Evaluation of experimental methods for determining dynamic stiffness and damping of composite materials

    Science.gov (United States)

    Bert, C. W.; Clary, R. R.

    1974-01-01

    Various methods potentially usable for determining dynamic stiffness and damping of composite materials are reviewed. Of these, the following most widely used techniques are singled out for more detailed discussion: free vibration, pulse propagation, and forced vibration response. To illustrate the usefulness and validity of dynamic property data, their application in dynamic analyses and comparison with measured structural response are described for the following composite-material structures: free-free sandwich beam with glass-epoxy facings, clamped-edge sandwich plate with similar facings, free-end sandwich conical shell with similar facings, and boron-epoxy free plate with layers arranged at various orientations.

  4. Molecular Dynamics of Materials Possessing High Energy Content.

    Science.gov (United States)

    1988-01-26

    I -RI90 634 MOLECULAR DYNAMICS OF MATERIALS POSSESSING HIGH ENERGY 1/1 r CONTENTCU) COLUMBIA UNIV MENd YORK N J TURRO 26 JAN GO I RFOSR-TR-88-0168...Bolling Air Force Base, D.C. 2 61102F_ 2303 I B2 11 T,TL.E (Inciuoe Security Classification) Molecular Dynamics of Materials Possessing High Energy...York 10027 (212) 280-2175 TITLE: MOLECULAR DYNAMICS OF MATERIALS POSSESSING HIGH ENERGY CONTENT .. 0 0 88 2 ... "" ’% ,i u , . .. .. ....... ŝ" ;! ,i

  5. Dynamic HMM Model with Estimated Dynamic Property in Continuous Mandarin Speech Recognition

    Institute of Scientific and Technical Information of China (English)

    CHENFeili; ZHUJie

    2003-01-01

    A new dynamic HMM (hiddem Markov model) has been introduced in this paper, which describes the relationship between dynamic property and feature of space. The method to estimate the dynamic property is discussed in this paper, which makes the dynamic HMMmuch more practical in real time speech recognition. Ex-periment on large vocabulary continuous Mandarin speech recognition task has shown that the dynamic HMM model can achieve about 10% of error reduction both for tonal and toneless syllable. Estimated dynamic property can achieve nearly same (even better) performance than using extracted dynamic property.

  6. State-of-the-art analytical methods for assessing dynamic bonding soft matter materials.

    Science.gov (United States)

    Brandt, Josef; Oehlenschlaeger, Kim K; Schmidt, Friedrich Georg; Barner-Kowollik, Christopher; Lederer, Albena

    2014-09-03

    Dynamic bonding materials are of high interest in a variety of fields in material science. The reversible nature of certain reaction classes is frequently employed for introducing key material properties such as the capability to self-heal. In addition to the synthetic effort required for designing such materials, their analysis is a highly complex--yet important--endeavor. Herein, we critically review the current state of the art analytical methods and their application in the context of reversible bonding on demand soft matter material characterization for an in-depth performance assessment. The main analytical focus lies on the characterization at the molecular level.

  7. Structural and Dynamical Properties of Polyethylene/Graphene Nanocomposites through Molecular Dynamics Simulations

    Directory of Open Access Journals (Sweden)

    Anastassia N. Rissanou

    2015-02-01

    Full Text Available Detailed atomistic (united atoms molecular dynamics simulations of several graphene based polymer (polyethylene, PE nanocomposite systems have been performed. Systems with graphene sheets of different sizes have been simulated at the same graphene concentration (~3%. In addition, a periodic graphene layer (“infinite sheet” has been studied. Results concerning structural and dynamical properties of PE chains are presented for the various systems and compared to data from a corresponding bulk system. The final properties of the material are the result of a complex effect of the graphene’s sheet size, mobility and fluctuations. A detailed investigation of density, structure and dynamics of the hybrid systems has been conducted. Particular emphasis has been given in spatial heterogeneities due to the PE/graphene interfaces, which were studied through a detailed analysis based on radial distances form the graphene’s center-of-mass. Chain segmental dynamics is found to be slower, compared to the bulk one, at the PE/graphene interface by a factor of 5 to 10. Furthermore, an analysis on the graphene sheets characteristics is presented in terms of conformational properties (i.e., wrinkling and mobility.

  8. Cytocompatibility and Antibacterial Properties of Capping Materials

    Science.gov (United States)

    Arciola, Carla Renata; Monaco, Annachiara; Lombardini, Marco

    2014-01-01

    The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply), Calcicur (Voco), Calcimol LC (Voco), TheraCal LC (Bisco), MTA Angelus (Angelus), and Biodentine (Septodont). To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towards rat MDPC-23 cells was evaluated at different times by both MTT and apoptosis assays. Results significantly differed among the different materials tested. Both bacterial growth inhibition halos and cytocompatibility performances were significantly different among materials with different composition. MTA-based products showed lower cytotoxicity and valuable antibacterial activity, different from calcium hydroxide-based materials, which exhibited not only higher antibacterial activity but also higher cytotoxicity. PMID:24959601

  9. Cytocompatibility and Antibacterial Properties of Capping Materials

    Directory of Open Access Journals (Sweden)

    Claudio Poggio

    2014-01-01

    Full Text Available The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply, Calcicur (Voco, Calcimol LC (Voco, TheraCal LC (Bisco, MTA Angelus (Angelus, and Biodentine (Septodont. To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towards rat MDPC-23 cells was evaluated at different times by both MTT and apoptosis assays. Results significantly differed among the different materials tested. Both bacterial growth inhibition halos and cytocompatibility performances were significantly different among materials with different composition. MTA-based products showed lower cytotoxicity and valuable antibacterial activity, different from calcium hydroxide-based materials, which exhibited not only higher antibacterial activity but also higher cytotoxicity.

  10. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  11. Absorption properties of waste matrix materials

    Energy Technology Data Exchange (ETDEWEB)

    Briggs, J.B. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1997-06-01

    This paper very briefly discusses the need for studies of the limiting critical concentration of radioactive waste matrix materials. Calculated limiting critical concentration values for some common waste materials are listed. However, for systems containing large quantities of waste materials, differences up to 10% in calculated k{sub eff} values are obtained by changing cross section data sets. Therefore, experimental results are needed to compare with calculation results for resolving these differences and establishing realistic biases.

  12. Cytocompatibility and Antibacterial Properties of Capping Materials

    OpenAIRE

    Claudio Poggio; Carla Renata Arciola; Riccardo Beltrami; Annachiara Monaco; Alberto Dagna; Marco Lombardini; Livia Visai

    2014-01-01

    The aim of this study was to evaluate and compare the antimicrobial activity and cytocompatibility of six different pulp-capping materials: Dycal (Dentsply), Calcicur (Voco), Calcimol LC (Voco), TheraCal LC (Bisco), MTA Angelus (Angelus), and Biodentine (Septodont). To evaluate antimicrobial activity, materials were challenged in vitro with Streptococcus mutans, Streptococcus salivarius, and Streptococcus sanguis in the agar disc diffusion test. Cytocompatibility of the assayed materials towa...

  13. Hierarchical Canopy Dynamics of Electrolyte-Doped Nanoscale Ionic Materials

    KAUST Repository

    Jespersen, Michael L.

    2013-12-23

    Nanoscale ionic materials (NIMs) are organic-inorganic hybrids prepared from ionically functionalized nanoparticles (NP) neutralized by oligomeric polymer counterions. NIMs are designed to behave as liquids under ambient conditions in the absence of solvent and have no volatile organic content, making them useful for a number of applications. We have used nuclear magnetic resonance relaxation and pulsed-field gradient NMR to probe local and collective canopy dynamics in NIMs based on 18-nm silica NPs with a covalently bound anionic corona, neutralized by amine-terminated ethylene oxide/propylene oxide block copolymers. The NMR relaxation studies show that the nanosecond-scale canopy dynamics depend on the degree of neutralization, the canopy radius of gyration, and crowding at the ionically modified NP surface. Two canopy populations are observed in the diffusion experiments, demonstrating that one fraction of the canopy is bound to the NP surface on the time scale (milliseconds) of the diffusion experiment and is surrounded by a more mobile layer of canopy that is unable to access the surface due to molecular crowding. The introduction of electrolyte ions (Na+ or Mg2+) screens the canopy-corona electrostatic interactions, resulting in a reduced bulk viscosity and faster canopy exchange. The magnitude of the screening effect depends upon ion concentration and valence, providing a simple route for tuning the macroscopic properties of NIMs. © 2013 American Chemical Society.

  14. Studies of molecular properties of polymeric materials

    Science.gov (United States)

    Harries, W. L.; Long, Sheila Ann T.; Long, Edward R., Jr.

    1990-01-01

    Aerospace environment effects (high energy electrons, thermal cycling, atomic oxygen, and aircraft fluids) on polymeric and composite materials considered for structural use in spacecraft and advanced aircraft are examined. These materials include Mylar, Ultem, and Kapton. In addition to providing information on the behavior of the materials, attempts are made to relate the measurements to the molecular processes occurring in the material. A summary and overview of the technical aspects are given along with a list of the papers that resulted from the studies. The actual papers are included in the appendices and a glossary of technical terms and definitions is included in the front matter.

  15. Dynamic properties of interfaces in soft matter: Experiments and theory

    NARCIS (Netherlands)

    Sagis, L.M.C.

    2011-01-01

    The dynamic properties of interfaces often play a crucial role in the macroscopic dynamics of multiphase soft condensed matter systems. These properties affect the dynamics of emulsions, of dispersions of vesicles, of biological fluids, of coatings, of free surface flows, of immiscible polymer

  16. Ultrafast Laser Dynamics and Interactions in Complex Materials

    Science.gov (United States)

    Patz, Aaron Edward

    The work described in this thesis underscores specific examples of using an ultrafast laser as a materials research tool for studying condensed matter physics in complex materials. The majority of materials studied fall into the iron-pnictide class of unconventional superconductors, which exhibit a multitude of phases that appear to be dependent on each other, or the magnetic semiconductor, GaMnAs. In my work I show various ultrafast laser techniques for studying these complex materials in order to decouple the different properties in the time-domain and gain information about the underlying physics governing the material properties.

  17. Dynamic brittle material response based on a continuum damage model

    Energy Technology Data Exchange (ETDEWEB)

    Chen, E.P.

    1994-12-31

    The response of brittle materials to dynamic loads was studied in this investigation based on a continuum damage model. Damage mechanism was selected to be interaction and growth of subscale cracks. Briefly, the cracks are activated by bulk tension and the density of activated cracks are described by a Weibull statistical distribution. The moduli of a cracked solid derived by Budiansky and O`Connell are then used to represent the global material degradation due to subscale cracking. This continuum damage model was originally developed to study rock fragmentation and was modified in the present study to improve on the post-limit structural response. The model was implemented into a transient dynamic explicit finite element code PRONTO 2D and then used for a numerical study involving the sudden stretching of a plate with a centrally located hole. Numerical results characterizing the dynamic responses of the material were presented. The effect of damage on dynamic material behavior was discussed.

  18. Ultrafast dynamic ellipsometry and spectroscopies of laser shocked materials

    Energy Technology Data Exchange (ETDEWEB)

    Mcgrane, Shawn David [Los Alamos National Laboratory; Bolme, Cindy B [Los Alamos National Laboratory; Whitley, Von H [Los Alamos National Laboratory; Moore, David S [Los Alamos National Laboratory

    2010-01-01

    Ultrafast ellipsometry and transient absorption spectroscopies are used to measure material dynamics under extreme conditions of temperature, pressure, and volumetric compression induced by shock wave loading with a chirped, spectrally clipped shock drive pulse.

  19. New elastoplastic materials with performance properties

    OpenAIRE

    Sanda VISAN,; Virginia CIOBOTARU; Florica IONESCU; Anca ANGELESCU

    2009-01-01

    The fabrication of high performance materials using EPDM rubber and polyethylene mixtures with a low cost, nonpolluting and minimum investment technology is studied. These new materials can be used for obtaining a lot of goods for the economy, sport and private life..

  20. New elastoplastic materials with performance properties

    Directory of Open Access Journals (Sweden)

    Sanda VISAN,

    2009-06-01

    Full Text Available The fabrication of high performance materials using EPDM rubber and polyethylene mixtures with a low cost, nonpolluting and minimum investment technology is studied. These new materials can be used for obtaining a lot of goods for the economy, sport and private life.

  1. Determination of the elasticity of parachute materials under dynamic loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Behr, V.L. [Sandia National Labs., Albuquerque, NM (United States); Clements, P.J.; Silbert, M.N. [Salisbury State Univ., MD (United States). Henson School of Science and Technology

    1996-12-31

    In the design of parachute systems it is important to use material properties that have been acquired under representative strain rates expected in flight. Without such data the designer is potentially forced to incorporate unrealistic safety margins resulting in a heavier and costlier than required design. Laboratory test data has generally been limited to that which can be acquired at quasi-steady strain rates. This paper investigates a technique, which takes advantage of advances in solid state electronics in the past ten years, to achieve an economical means of acquiring material properties under dynamic strain conditions. Data obtained with this technique is compared to standard test data for representative parachute materials.

  2. Optical studies of dynamical processes in disordered materials

    Energy Technology Data Exchange (ETDEWEB)

    Yen, W.M.

    1991-07-01

    In general terms, our research activities under the present Agency sponsorship continue to focus on processes and interactions which affect the dynamical behavior of excitations/excited states of optically activated amorphous or disordered solids. The framework of our understanding of these processes has been established with work performed over the past two decades. The advent of more refined spectroscopies, most of them laser based, has allowed a re-examination of these properties in a much more detailed and basic way. A deeper understanding of the interactions which lead to relaxation, energy diffusion and nonlinearities in the disordered phases is important to the development of more efficient and better materials to service all of the technologies which employ optically activated materials. In this document, we will present an abbreviated synopsis of the research we have conducted under the auspices of the present grant. We will then outline directions we wish to maintain and will render descriptions of new opportunities which have ensued from our current efforts and which we wish to exploit under renewed sponsorship. 52 refs., 12 figs.

  3. Magnon-phonon interconversion in a dynamically reconfigurable magnetic material

    Science.gov (United States)

    Guerreiro, Sergio C.; Rezende, Sergio M.

    2015-12-01

    The ferrimagnetic insulator yttrium iron garnet (YIG) is an important material in the field of magnon spintronics, mainly because of its low magnetic losses. YIG also has very low acoustic losses, and for this reason the conversion of a state of magnetic excitation (magnons) into a state of lattice vibration (phonons), or vice versa, broadens its possible applications in spintronics. Since the magnetic parameters can be varied by some external action, the magnon-phonon interconversion can be tuned to perform a desired function. We present a quantum theory of the interaction between magnons and phonons in a ferromagnetic material subject to a dynamic variation of the applied magnetic field. It is shown that when the field gradient at the magnetoelastic crossover region is much smaller than a critical value, an initial elastic excitation can be completely converted into a magnetic excitation, or vice versa. This occurs with conservation of linear momentum and spin angular momentum, implying that phonons created by the conversion of magnons have spin angular momentum and carry spin current. It is shown further that if the system is initially in a quantum coherent state, its coherence properties are maintained regardless of the time dependence of the field.

  4. Dynamic High-Pressure Behavior of Hierarchical Heterogeneous Geological Materials

    Science.gov (United States)

    2016-04-01

    pressure -density Hugoniot plots for simulations using the ‘mix 5’ option, as will be presented later. The volume weighted option for mixed cells (refered...AFRL-AFOSR-VA-TR-2016-0150 Dynamic High- Pressure Behavior of Geological Materials Naresh Thadhani GEORGIA TECH RESEARCH CORPORATION Final Report 04...31-12-2015 4.  TITLE AND SUBTITLE Dynamic High- Pressure Behavior of Hierarchical Heterogeneous Geological Materials 5a.  CONTRACT NUMBER 5b.  GRANT

  5. Textile materials for lightweight constructions technologies, methods, materials, properties

    CERN Document Server

    2016-01-01

    In this book, experts on textile technologies convey both general and specific informa­tion on various aspects of textile engineering, ready-made technologies, and textile chemistry. They describe the entire process chain from fiber materials to various yarn constructions, 2D and 3D textile constructions, preforms, and interface layer design. In addition, the authors introduce testing methods, shaping and simulation techniques for the characterization of and structural mechanics calculations on anisotropic, pliable high-performance textiles, including specific examples from the fields of fiber plastic composites, textile concrete, and textile membranes. Readers will also be familiarized with the potential offered by increasingly popular textile structures, for instance in the fields of composite technology, construction technology, security technology, and membrane technology. Textile materials and semi-finished products have widely varied potential characteristics, and are commonly used as essential element...

  6. Measurements of Acoustic Properties of Porous and Granular Materials and Application to Vibration Control

    Science.gov (United States)

    Park, Junhong; Palumbo, Daniel L.

    2004-01-01

    For application of porous and granular materials to vibro-acoustic controls, a finite dynamic strength of the solid component (frame) is an important design factor. The primary goal of this study was to investigate structural vibration damping through this frame wave propagation for various poroelastic materials. A measurement method to investigate the vibration characteristics of the frame was proposed. The measured properties were found to follow closely the characteristics of the viscoelastic materials - the dynamic modulus increased with frequency and the degree of the frequency dependence was determined by its loss factor. The dynamic stiffness of hollow cylindrical beams containing porous and granular materials as damping treatment was measured also. The data were used to extract the damping materials characteristics using the Rayleigh-Ritz method. The results suggested that the acoustic structure interaction between the frame and the structure enhances the dissipation of the vibration energy significantly.

  7. Elastic properties of superconductors and materials with weakly correlated spins.

    Science.gov (United States)

    Binek, Christian

    2017-07-07

    It is shown that in the ergodic regime, the temperature dependence of Young's modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young's modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Constant diamagnetic susceptibility gives rise to a temperature independent elastic modulus for ceramic and single crystalline superconductors alike. The thermodynamic approach established in this report, paves the way to tailor elastic material parameters through the design of magnetic properties.

  8. Ultrafast impact dynamics of reactive materials (Dlott)

    Science.gov (United States)

    2013-04-16

    Submitted Patents Awarded Awards Jupiter Laser Facility Program Advisory Committee, Lawrence Livermore National Laboratory, 2008, 2011 Executive...related materials such as B/Teflon) to ultrafast laser flash heating. 36-39 In fact during the project period we wrapped up the flash-heating

  9. Numerical simulations of granular dynamics II. Particle dynamics in a shaken granular material

    CERN Document Server

    Murdoch, Naomi; Richardson, Derek C; Nordstrom, Kerstin; Berardi, Christian R; Green, Simon F; Losert, Wolfgang

    2013-01-01

    Surfaces of planets and small bodies of our Solar System are often covered by a layer of granular material that can range from a fine regolith to a gravel-like structure of varying depths. Therefore, the dynamics of granular materials are involved in many events occurring during planetary and small-body evolution thus contributing to their geological properties. We demonstrate that the new adaptation of the parallel N-body hard-sphere code pkdgrav has the capability to model accurately the key features of the collective motion of bidisperse granular materials in a dense regime as a result of shaking. As a stringent test of the numerical code we investigate the complex collective ordering and motion of granular material by direct comparison with laboratory experiments. We demonstrate that, as experimentally observed, the scale of the collective motion increases with increasing small-particle additive concentration. We then extend our investigations to assess how self-gravity and external gravity affect collect...

  10. Optimization of Structure and Material Properties for Solids Composed of Softening Material

    DEFF Research Database (Denmark)

    Bendsøe, Martin P.; Guedes, J.M.; J.M., Plaxton;

    1996-01-01

    Recent results on the design of material properties in the context of global structural optimization provide, in analytical form, a prediction of the optimal material tensor distributions for two or three dimensional continuum structures. The model developed for that purpose is extended here...... to cover the design of a structure and associated material properties for a system composed of a generic form of nonlinear softening material. As was established in the earlier study on design with linear materials, the formulation for combined 'material and structure' design with softening materials can...

  11. Dynamical Properties of Internal Shocks Revisited

    CERN Document Server

    Pe'er, Asaf; Casella, Piergiorgio

    2016-01-01

    Internal shocks between propagating plasma shells, originally ejected at different times with different velocities are believed to play a major role in dissipating the kinetic energy, thereby explaining the observed lightcurve and spectra in a large range of transient objects. Even if initially the colliding plasmas are cold, following the first collision the plasma shells are substantially heated, implying that in a scenario of multiple collisions, most collisions take place between plasmas of non-zero temperatures. Here, we calculate the dynamical properties of plasmas resulting from collision between arbitrarily hot plasma shells, moving at arbitrary speeds. We provide simple analytical expressions valid for both the ultra-relativistic and Newtonian velocities, for both hot and cold plasmas. We derive the minimum criteria required for the formation of the two-shock wave system, and show that in the relativistic limit, the minimum Lorentz factor is proportional to the square root of the ratio of the initial...

  12. Superconductivity and magnetism: Materials properties and developments

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, N.H.; Bay, N.; Grivel, J.C. (eds.) [and others

    2003-07-01

    The 24th Risoe International Symposium on Materials Science focuses on development of new materials, devices and applications, as well as experimental and theoretical studies of novel and unexplained phenomena in superconductivity and magnetism, e.g. within high.T{sub c} superconductivity, magnetic superconductors, MgB{sub 2}, CMR materials, nanomagnetism and spin-tronics. The aim is to stimulate exchange of ideas and establish new collaborations between leading Danish and international scientists. The topics are addressed by presentations from 24 invited speakers and by 41 contributed papers. (ln)

  13. Fundamental Material Properties Underlying Solid Oxide Electrochemistry

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Hansen, Karin Vels; Holtappels, Peter

    2012-01-01

    and electronic conductor (MIEC) the electrode is. Selected examples of literature studies of specific electrodes in solid oxide cells (SOC) are discussed. The reported effects of impurities - both impurities in the electrode materials and in the gases – point to high reactivity and mobility of materials...... in the TPB region. Also, segregations to the surfaces and interfaces of the electrode materials, which may affect the electrode reaction mechanism, are very dependent on the exact history of fabrication and operation. The positive effects of even small concentrations of nanoparticles in the electrodes may...

  14. Dynamic mechanical properties of an inlay composite.

    Science.gov (United States)

    Dionysopoulos, P; Watts, D C

    1989-06-01

    A visible light-cured composite resin (Brilliant DI) has been studied over a wide range of temperature and frequency by a dynamic mechanical flexural method. The derived data of logarithmic modulus and loss tangent (tan delta) show considerable changes following a secondary-cure process applied to the material. This involved the application of heat and intense light with temperatures rising to 120 degrees C in 7 min. Following this oven-cure the resin phase exhibited enhanced stiffness with the activation-energy barrier for molecular motion at the glass-transition rising from 220 to 291 kJ/mol. This study clarifies the nature and extent of the internal molecular changes which may be produced in the fabrication of a composite inlay.

  15. Optical properties and electron dynamics in carbon nanodots

    Science.gov (United States)

    Wen, Xiaoming; Huang, Shujuan; Conibeer, Gavin; Shrestha, Santosh; Yu, Pyng; Toh, Yon-Rui; Tang, Jau

    2013-12-01

    Carbon nanodots (CNDs) have emerged as fascinating materials with exceptional electronic and optical properties, and thus they offer promising applications in photonics, photovoltaics and photocatalysis. Herein we study the optical properties and electron dynamics in CNDs using steady state and time-resolved spectroscopy. The photoluminescence (PL) is determined to originate from both core and surface. The massive surface fluorophores result in a broad spectral fluorescence. In addition to various synthesis techniques, it is demonstrated that the PL of CNDs can be extended from the blue to the near infrared by thermal assisted growth. Directional electron transfer was observed as fast as femtosecond in CND-graphene oxide nanocomposites from CND into graphene oxide. These results suggest CNDs can be promising in many applications.

  16. Fundamental Material Properties Underlying Solid Oxide Electrochemistry

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Hansen, Karin Vels; Holtappels, Peter

    2012-01-01

    and electronic conductor (MIEC) the electrode is. Selected examples of literature studies of specific electrodes in solid oxide cells (SOC) are discussed. The reported effects of impurities - both impurities in the electrode materials and in the gases – point to high reactivity and mobility of materials...... place. The length of the TPB is a key factor even though the width and depth of the zone, in which the rate limiting reactions take place, may vary depending of the degree of the electrode materials ability to conduct both electrons and ions, i.e. the TPB zone volume depends on how good a mixed ionic...... in the TPB region. Also, segregations to the surfaces and interfaces of the electrode materials, which may affect the electrode reaction mechanism, are very dependent on the exact history of fabrication and operation. The positive effects of even small concentrations of nanoparticles in the electrodes may...

  17. Optical properties of active photonic materials

    OpenAIRE

    Zeng, Yong

    2007-01-01

    Because of the generation of polaritons, which are quasiparticles possessing the characteristics of both photonics and electronics, active photonic materials offer a possible solution to transfer electromagnetic energy below the diffraction limit and further increase the density of photonic integrated circuits. A theoretical investigation of these exciting materials is, therefore, very important for practical applications. Four different kinds of polaritons have been studied in this thesis, (...

  18. Dynamic Properties of Human Bronchial Airway Tissues

    CERN Document Server

    Wang, Jau-Yi; Pallai, Prathap; Corrigan, Chris J; Lee, Tak H

    2011-01-01

    Young's Modulus and dynamic force moduli were measured on human bronchial airway tissues by compression. A simple and low-cost system for measuring the tensile-strengh of soft bio-materials has been built for this study. The force-distance measurements were undertaken on the dissected bronchial airway walls, cartilages and mucosa from the surgery-removed lungs donated by lung cancer patients with COPD. Young's modulus is estimated from the initial slope of unloading force-displacement curve and the dynamic force moduli (storage and loss) are measured at low frequency (from 3 to 45 Hz). All the samples were preserved in the PBS solution at room temperature and the measurements were perfomed within 4 hours after surgery. Young's modulus of the human bronchial airway walls are fond ranged between 0.17 and 1.65 MPa, ranged between 0.25 to 1.96 MPa for cartilages, and between 0.02 to 0.28 MPa for mucosa. The storage modulus are found varying 0.10 MPa with frequency while the loss modulus are found increasing from ...

  19. Elastic properties of superconductors and materials with weakly correlated spins

    OpenAIRE

    Binek, Christian

    2017-01-01

    It is shown that in the ergodic regime, the temperature dependence of Young?s modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young?s modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Const...

  20. Lattice dynamical studies of HTSC materials

    Energy Technology Data Exchange (ETDEWEB)

    Pintschovius, L.; Pyka, N.; Reichardt, W. (Kernforschungszentrum Karlsruhe, INFP (Germany)); Rumiantsev, A.Yu.; Mitrofanov, N.L.; Ivanov, A.S. (I.V. Kurchatov-Inst. of Atomic Energy, Moscow (USSR)); Collin, G.; Bourges, P. (Lab. Leon Brillouin, CEA-CNRS, CEN Saclay, 91 - Gif-sur-Yvette (France))

    1991-12-01

    A survey is presented on recent progress in the understanding of the lattice dynamics in Nd{sub 2}CuO{sub 4}, (La,Sr){sub 2}CuO{sub 4} and YBa{sub 2}Cu{sub 3}O{sub 6/7}. Classical anharmonicity and twinning were found to be major complications for the interpretation of the data. The lattice vibrations of the cuprates can now largely be described within the framework of shell models for strongly ionic compounds. Phonon anomalies inferred from a comparison of doped and undoped compounds resemble those found in classical superconductors. (orig.).

  1. Compaction dynamics of crunchy granular material

    Directory of Open Access Journals (Sweden)

    Guillard François

    2017-01-01

    Full Text Available Compaction of brittle porous material leads to a wide variety of densification patterns. Static compaction bands occurs naturally in rocks or bones, and have important consequences in industry for the manufacturing of powder tablets or metallic foams for example. Recently, oscillatory compaction bands have been observed in brittle porous media like snow or cereals. We will discuss the great variety of densification patterns arising during the compaction of puffed rice, including erratic compaction at low velocity, one or several travelling compaction bands at medium velocity and homogeneous compaction at larger velocity. The conditions of existence of each pattern are studied thanks to a numerical spring lattice model undergoing breakage and is mapped to the phase diagram of the patterns based on dimensionless characteristic quantities. This also allows to rationalise the evolution of the compaction behaviour during a single test. Finally, the localisation of compaction bands is linked to the strain rate sensitivity of the material.

  2. Dynamics of Drying in Phenolically Tanned Materials

    Institute of Scientific and Technical Information of China (English)

    Julian F. V. Vincent

    2004-01-01

    The cuticle of a maggot goes through a mechanical transition when it dries, increasing in stiffness by about an order of magnitude (e. g. from 0.5 GPa to 5 GPa) as the water content drops from about 1 g/g (weight of water per unit dry weight) to 0.4 g/g. Thus stiffness represents the loss of freezable water and is more or less diagnostic of a material stabilized by hydrogen bonds. Further loss in water results in a smaller increase in stiffness. In natural systems the water content is controlled by the addition of phenolic residues, resulting in tanning or sclerotisation, which drives the matrix components towards co-operative interaction and makes the material permanently waterproof.

  3. Shock waves simulated using the dual domain material point method combined with molecular dynamics

    Science.gov (United States)

    Zhang, Duan Z.; Dhakal, Tilak R.

    2017-04-01

    In this work we combine the dual domain material point method with molecular dynamics in an attempt to create a multiscale numerical method to simulate materials undergoing large deformations with high strain rates. In these types of problems, the material is often in a thermodynamically nonequilibrium state, and conventional constitutive relations or equations of state are often not available. In this method, the closure quantities, such as stress, at each material point are calculated from a molecular dynamics simulation of a group of atoms surrounding the material point. Rather than restricting the multiscale simulation in a small spatial region, such as phase interfaces, or crack tips, this multiscale method can be used to consider nonequilibrium thermodynamic effects in a macroscopic domain. This method takes the advantage that the material points only communicate with mesh nodes, not among themselves; therefore molecular dynamics simulations for material points can be performed independently in parallel. The dual domain material point method is chosen for this multiscale method because it can be used in history dependent problems with large deformation without generating numerical noise as material points move across cells, and also because of its convergence and conservation properties. To demonstrate the feasibility and accuracy of this method, we compare the results of a shock wave propagation in a cerium crystal calculated using the direct molecular dynamics simulation with the results from this combined multiscale calculation.

  4. ABINIT: First-principles approach to material and nanosystem properties

    Science.gov (United States)

    Gonze, X.; Amadon, B.; Anglade, P.-M.; Beuken, J.-M.; Bottin, F.; Boulanger, P.; Bruneval, F.; Caliste, D.; Caracas, R.; Côté, M.; Deutsch, T.; Genovese, L.; Ghosez, Ph.; Giantomassi, M.; Goedecker, S.; Hamann, D. R.; Hermet, P.; Jollet, F.; Jomard, G.; Leroux, S.; Mancini, M.; Mazevet, S.; Oliveira, M. J. T.; Onida, G.; Pouillon, Y.; Rangel, T.; Rignanese, G.-M.; Sangalli, D.; Shaltaf, R.; Torrent, M.; Verstraete, M. J.; Zerah, G.; Zwanziger, J. W.

    2009-12-01

    ABINIT [ http://www.abinit.org] allows one to study, from first-principles, systems made of electrons and nuclei (e.g. periodic solids, molecules, nanostructures, etc.), on the basis of Density-Functional Theory (DFT) and Many-Body Perturbation Theory. Beyond the computation of the total energy, charge density and electronic structure of such systems, ABINIT also implements many dynamical, dielectric, thermodynamical, mechanical, or electronic properties, at different levels of approximation. The present paper provides an exhaustive account of the capabilities of ABINIT. It should be helpful to scientists that are not familiarized with ABINIT, as well as to already regular users. First, we give a broad overview of ABINIT, including the list of the capabilities and how to access them. Then, we present in more details the recent, advanced, developments of ABINIT, with adequate references to the underlying theory, as well as the relevant input variables, tests and, if available, ABINIT tutorials. Program summaryProgram title: ABINIT Catalogue identifier: AEEU_v1_0 Distribution format: tar.gz Journal reference: Comput. Phys. Comm. Programming language: Fortran95, PERL scripts, Python scripts Computer: All systems with a Fortran95 compiler Operating system: All systems with a Fortran95 compiler Has the code been vectorized or parallelized?: Sequential, or parallel with proven speed-up up to one thousand processors. RAM: Ranges from a few Mbytes to several hundred Gbytes, depending on the input file. Classification: 7.3, 7.8 External routines: (all optional) BigDFT [1], ETSF IO [2], libxc [3], NetCDF [4], MPI [5], Wannier90 [6] Nature of problem: This package has the purpose of computing accurately material and nanostructure properties: electronic structure, bond lengths, bond angles, primitive cell size, cohesive energy, dielectric properties, vibrational properties, elastic properties, optical properties, magnetic properties, non-linear couplings, electronic and

  5. Simultaneous dynamic electrical and structural measurements of functional materials

    Energy Technology Data Exchange (ETDEWEB)

    Vecchini, C.; Stewart, M.; Muñiz-Piniella, A.; Wooldridge, J. [National Physical Laboratory, Hampton Road, Teddington TW11 0LW (United Kingdom); Thompson, P.; McMitchell, S. R. C.; Bouchenoire, L.; Brown, S.; Wermeille, D.; Lucas, C. A. [XMaS, The UK-CRG, ESRF-The European Synchrotron, CS40220, F-38043, Grenoble Cedex 09 (France); Department of Physics, University of Liverpool, Liverpool L69 3BX (United Kingdom); Lepadatu, S. [National Physical Laboratory, Hampton Road, Teddington TW11 0LW (United Kingdom); Jeremiah Horrocks Institute, University of Central Lancashire, Preston PR1 2HE (United Kingdom); Bikondoa, O.; Hase, T. P. A. [XMaS, The UK-CRG, ESRF-The European Synchrotron, CS40220, F-38043, Grenoble Cedex 09 (France); Department of Physics, University of Warwick, Coventry CV4 7AL (United Kingdom); Lesourd, M. [ESRF-The European Synchrotron, CS40220, F-38043, Grenoble Cedex 09 (France); Dontsov, D. [SIOS Meßtechnik GmbH, Am Vogelherd 46, 98693 Ilmenau (Germany); Cain, M. G. [National Physical Laboratory, Hampton Road, Teddington TW11 0LW (United Kingdom); Electrosciences Ltd., Farnham, Surrey GU9 9QT (United Kingdom)

    2015-10-15

    A new materials characterization system developed at the XMaS beamline, located at the European Synchrotron Radiation Facility in France, is presented. We show that this new capability allows to measure the atomic structural evolution (crystallography) of piezoelectric materials whilst simultaneously measuring the overall strain characteristics and electrical response to dynamically (ac) applied external stimuli.

  6. A continuum theory for modeling the dynamics of crystalline materials.

    Science.gov (United States)

    Xiong, Liming; Chen, Youping; Lee, James D

    2009-02-01

    This paper introduces a multiscale field theory for modeling and simulation of the dynamics of crystalline materials. The atomistic formulation of a multiscale field theory is briefly introduced. Its applicability is discussed. A few application examples, including phonon dispersion relations of ferroelectric materials BiScO3 and MgO nano dot under compression are presented.

  7. Dynamic viscoelastic properties of polyvinyl chloride with physical aging

    Science.gov (United States)

    Tian, Fang; Luo, Yingshe; Yin, Shuiping; Wang, Hong; Cao, Chun

    2015-11-01

    The experimental research of dynamic viscoelastic properties of polyvinyl chloride was conducted by the dynamic mechanical analysis method in this paper. And the fitting equation of dynamic modulus of polymers has been presented. Based on the time-aging time equivalent principle, horizontal shift factor and vertical shift factor of aging time are carried out, which proposes a novel method for the research on time-aging time equivalent analysis of dynamic mechanical properties of polymers during physical aging.

  8. Dielectric properties of materials at microwave frequencies

    Directory of Open Access Journals (Sweden)

    Ivo Křivánek

    2008-01-01

    Full Text Available The paper introduces the review of the present state of art in the measurement of the interaction of electromagnetic waves with different kinds of materials. It is analysis of the possibilities of the mea­surement of the interaction of high frequencies waves (microwaves with materials and proposal of the experimental method for the studies mentioned above.The electromagnetic field consists of two components: electric and magnetic field. The influence of these components on materials is different. The influence of the magnetic field is negligible and it has no impact on practical use. The influence of the electric field is strong as the interaction between them results in the creation of electric currents in the material (Křivánek and Buchar, 1993.Experiments focused on the evaluation of the complex dielectric permitivity of different materials have been performed. The permitivity of solid material is also measurable by phasemethod, when the specimen is a part of transmission sub-circuit. Microwave instrument for complex permittivity measurement works in X frequency band (8.2–12.5 GHz, the frequency 10.1 GHz was used for all the measurement in the laboratory of physics, Mendel University in Brno. The extensive number of experimental data have been obtained for different materials. The length of the square side of the ae­rial open end was 50 mm and internal dimensions of waveguides were 23 mm × 10 mm. The samples have form of the plate shape with dimensions 150 mm × 150 mm × 4 mm.

  9. Test Methods for Measuring Material Properties of Composite Materials in all Three Material Axes

    Science.gov (United States)

    2012-01-24

    conducted using ASTM D 6641/D 6641M “Standard Test Method for Determining the Compressive Properties of Polymer Matrix Composite Laminates Using a Combined...D 7291/D 7291M “Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber- Reinforced Polymer Matrix Composite Material...34Flatwise" Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material”. West Conshohocken, PA, 2005, DOI: 10.1520/D7291

  10. Tribological Property of Polyimide Porous Materials

    Institute of Scientific and Technical Information of China (English)

    PU Yu-ping; L(U) Guang-shu; LI Xiao-jun; XIAO Han-cheng

    2006-01-01

    The friction performance of the polyimide (PI) porous composite materials made by moulding method with MoS2 or polytetrafluoroethylene (PTFE) appended are disserted. The result shows that all the PI-based porous composites have the performance of transfer lubrication in the friction process, and the transfer film is built between the counter friction bodies; with the increasing of the MoS2 a mount from 0 to 20%, the friction coefficient trends toward decrease, and the tr ansfer lubricate phenomenon become more obvious; when adding PTFE as synergist t o the porous PI+MoS2 composite material, the synergistic effect happens, which can improve the friction performance of the material effectively.

  11. Structure and Properties of Energetic Materials

    Science.gov (United States)

    1992-12-02

    7.76 9.11 30 Gurney energy (MJ/kg) 1.1 1.6 30 Heat of detonation (MJ/kg) -5.02 -6.78 30 In Table 2 we compare the properties of TATB and...velocity of HMX is some 17% greater than that of TATB, the Gurney energy 45% greater, and the heat of detonation 35% greater One reason that TATB...MJ/kg) 1.1 1.6 30 Heat of detonation (MJ/kg) -5.02 -6.78 30 In Table 2 we compare the properties of TATB and cyclotetramethylenetetranitramine (HMX

  12. Adsorption Properties of Chalk Reservoir Materials

    DEFF Research Database (Denmark)

    Okhrimenko, Denis

    Understanding adsorption energetics and wetting properties of calcium carbonate surfaces is essential for developing remediation strategies for aquifers, improving oil recovery, minimising risk in CO2 storage and optimising industrial processes. This PhD was focussed on comparing the vapour....../gas adsorption properties of synthetic calcium carbonate phases (calcite, vaterite and aragonite) with chalk, which is composed of biogenic calcite (>98%). In combination with data from nanotechniques, the results demonstrate the complexity of chalk behavior and the role of nanoscale clay particles. The results...

  13. Organic materials with nonlinear optical properties

    Science.gov (United States)

    Stupp, Samuel I.; Son, Sehwan; Lin, Hong-Cheu

    1995-01-01

    The present invention is directed to organic materials that have the ability to double or triple the frequency of light that is directed through the materials. Particularly, the present invention is directed to the compound 4-[4-(2R)-2-cyano-7-(4'-pentyloxy-4-biphenylcarbonyloxy)phenylheptylidene) phenylcarbonyloxy]benzaldehyde, which can double the frequency of light that is directed through the compound. The invention is also directed to the compound (12-hydroxy-5,7-dodecadiynyl) 4'-[(4'-pentyloxy-4-biphenyl)carbonyloxy]-4-biphenylcarboxylate, and its polymeric form. The polymeric form can triple the frequency of light directed through it.

  14. Thermoviscoelastic dynamic response for a composite material thin narrow strip

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Hong Liang; Qi, Li-Li; Liu, Hai-Bo [Hunan University, Changsha (China)

    2015-02-15

    Based on von Karman nonlinear strain-displacement relationships and classical thin plate theory, a list of nonlinear dynamic equilibrium equations for a viscoelastic composite material thin narrow strip under thermal and mechanic loads are deduced. According to the material constitutive relationship and the relaxation modulus in the form of the Prony series, combing with the Newmark method and the Newton-cotes integration method, a new numerical algorithm for direct solving the whole problem in the time domain is established. By applying this numerical algorithm, the viscoelastic composite material thin narrow strip as the research subject is analyzed systematically, and its rich dynamical behaviors are revealed comprehensively. To verify the accuracy of the present work, a comparison is made with previously published results. Finally, the viscoelastic composite material thin narrow strip under harmonic excitation load and impact load are discussed in detail, and many valuable thermoviscoelastic dynamic characteristics are revealed.

  15. Finite Element Method for Analysis of Material Properties

    DEFF Research Database (Denmark)

    Rauhe, Jens Christian

    description of the material microstructure the finite element models must contain a large number of elements and this problem is solved by using the preconditioned conjugated gradient solver with an Element-By-Element preconditioner. Finite element analysis provides the volume averaged stresses and strains...... and the finite element method. The material microstructure of the heterogeneous material is non-destructively determined using X-ray microtomography. A software program has been generated which uses the X-ray tomographic data as an input for the mesh generation of the material microstructure. To obtain a proper...... which are used for the determination of the effective properties of the heterogeneous material. Generally, the properties determined using the finite element method coupled with X-ray microtomography are in good agreement with both experimentally determined properties and properties determined using...

  16. Handbook of the Properties of Optical Materials

    Science.gov (United States)

    1984-01-01

    EFFECTIVE MASS - - MOBILITY - - A-2 ARSEWIC SELENIOE (As2 Se3 ) OPTICAL PROPERTIES TRANSMISSION RANGE: 9 - 11n Optical Absorption Coefficient = 0.079...of 55 KRS-5 as a function of wavelength. A-2120 ZINC SELENIOE ZnSe 0 STRUCTURE CRYSTALLINE SYMMETRY = Cubic, 43m LATTICE CONSTANTS (A) = a = 5.667

  17. Adsorption Properties of Chalk Reservoir Materials

    DEFF Research Database (Denmark)

    Okhrimenko, Denis

    Understanding adsorption energetics and wetting properties of calcium carbonate surfaces is essential for developing remediation strategies for aquifers, improving oil recovery, minimising risk in CO2 storage and optimising industrial processes. This PhD was focussed on comparing the vapour...

  18. Thermal and Thermoelectric Properties of Nanostructured Materials and Interfaces

    Science.gov (United States)

    Liao, Hao-Hsiang

    Many modern technologies are enabled by the use of thin films and/or nanostructured composite materials. For example, many thermoelectric devices, solar cells, power electronics, thermal barrier coatings, and hard disk drives contain nanostructured materials where the thermal conductivity of the material is a critical parameter for the device performance. At the nanoscale, the mean free path and wavelength of heat carriers may become comparable to or smaller than the size of a nanostructured material and/or device. For nanostructured materials made from semiconductors and insulators, the additional phonon scattering mechanisms associated with the high density of interfaces and boundaries introduces additional resistances that can significantly change the thermal conductivity of the material as compared to a macroscale counterpart. Thus, better understanding and control of nanoscale heat conduction in solids is important scientifically and for the engineering applications mentioned above. In this dissertation, I discuss my work in two areas dealing with nanoscale thermal transport: (1) I describe my development and advancement of important thermal characterization tools for measurements of thermal and thermoelectric properties of a variety of materials from thin films to nanostructured bulk systems, and (2) I discuss my measurements on several materials systems done with these characterization tools. First, I describe the development, assembly, and modification of a time-domain thermoreflectance (TDTR) system that we use to measure the thermal conductivity and the interface thermal conductance of a variety of samples including nanocrystalline alloys of Ni-Fe and Co-P, bulk metallic glasses, and other thin films. Next, a unique thermoelectric measurement system was designed and assembled for measurements of electrical resistivity and thermopower of thermoelectric materials in the temperature range of 20 to 350 °C. Finally, a commercial Anter Flashline 3000 thermal

  19. Using nonlinearity and spatiotemporal property modulation to control effective structural properties: dynamic rods

    DEFF Research Database (Denmark)

    Thomsen, Jon Juel; Blekhman, Iliya I.

    2007-01-01

    , and to call these dynamic materials or spatiotemporal composites. Also, according to theoretical predictions, structural nonlinearity enhances the possibilities of achieving specific effective properties. For example, with an elastic rod having cubical elastic nonlinearities, it seems possible to control......, and exemplified. Then simple approximate analytical expressions are derived for the effective wave speed and natural frequencies for one-dimensional wave propagation in a nonlinear elastic rod, where the spatiotemporal modulation is imposed as a high-frequency standing wave, supposed to be given. Finally the more...

  20. Preparation of MWNTs/PI nanocomposite materials and their dynamic mechanical properties and dielectric properties%碳纳米管/聚酰亚胺纳米复合材料的制备及动态力学性能和介电性能

    Institute of Scientific and Technical Information of China (English)

    贺国文; 谢玲; 谭凯元; 李衡峰

    2011-01-01

    The multi-walled carbon nanotubes (MWNTs) were modified by mixed strong acids and sulfuryl dichloride (SOCl2) successively. Their solubility in organic solvents and dispersivity in matrix of polyimides were improved greatly by modification. The unmodified and modified MWNTs were characterized by X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). The polyimide (PI)/MWNTs composites were synthesized by in situ polymerization of 4,4'-diaminodiphenylether (ODA) and 3,3',4,4'-benzophenonetetracarboxylic dianhydride (BTDA), in which the modified MWNTs were used as the fillers. The composites were characterized by thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and measurement of capacitance. The results show that the PI/MWNTs composites have preferable heat stability as the same as the pure polyimide (PI). The dynamic mechanical properties improve with the mass fraction of MWNTs increasing. The value of storage modulus is 2.03 GPa at 50 ℃ when the mass fiaction of MWNTs is 10%. Compared with that of the pure PI, the storage modulus increases by 23.1%. The dielectric properties enhance sharply with the mass fraction of MWNTs increasing. For the nanocomposites containing 10% of MWNTs, the dielectric constant reaches 66.7 at 1 MHz, which comes up to 18.6 times of that of pure polyimide.Therefore, The MWNTs/PI is a kind of nanocomposite material with favorable properties of thermal properties, dynamic mechanical properties and dielectric properties.%依次用混强酸和SOCl2对多壁碳纳米管(MWNTs)进行改性,解决其在有机溶剂的溶解性和在基体聚酰亚胺中分散性问题,并采用光电子能谱(XPS)和透射电镜(TEM)对改性前后的MWNTs进行表征.以4,4'-二氨基二苯醚(ODA)和3,3',4,4'-二苯甲酮四羧酸二酐(BTDA)为原料,以原位聚合法将改性碳纳米管掺杂聚酰亚胺(PI),制备MWNTs/PI纳米复合材料.通过热重分析(TGA)、动态力学分析(DMA)和电

  1. Modification of Textile Materials' Surface Properties Using Chemical Softener

    Directory of Open Access Journals (Sweden)

    Jurgita KOŽENIAUSKIENĖ

    2011-03-01

    Full Text Available In the present study the effect of technological treatment involving the processes of washing or washing and softening with chemical cationic softener "Surcase" produced in Great Britain on the surface properties of cellulosic textile materials manufactured from cotton, bamboo and viscose spun yarns was investigated. The changes in textile materials surface properties were evaluated using KTU-Griff-Tester device and FEI Quanta 200 FEG scanning electron microscope (SEM. It was observed that the worst hand properties and the higher surface roughness are observed of cotton materials if compared with those of bamboo and viscose materials. Also, it was shown that depending on the material structure the handle parameters of knitted materials are the better than the ones of woven fabrics.http://dx.doi.org/10.5755/j01.ms.17.1.249

  2. Multiscale Modeling of Carbon/Phenolic Composite Thermal Protection Materials: Atomistic to Effective Properties

    Science.gov (United States)

    Arnold, Steven M.; Murthy, Pappu L.; Bednarcyk, Brett A.; Lawson, John W.; Monk, Joshua D.; Bauschlicher, Charles W., Jr.

    2016-01-01

    Next generation ablative thermal protection systems are expected to consist of 3D woven composite architectures. It is well known that composites can be tailored to achieve desired mechanical and thermal properties in various directions and thus can be made fit-for-purpose if the proper combination of constituent materials and microstructures can be realized. In the present work, the first, multiscale, atomistically-informed, computational analysis of mechanical and thermal properties of a present day - Carbon/Phenolic composite Thermal Protection System (TPS) material is conducted. Model results are compared to measured in-plane and out-of-plane mechanical and thermal properties to validate the computational approach. Results indicate that given sufficient microstructural fidelity, along with lowerscale, constituent properties derived from molecular dynamics simulations, accurate composite level (effective) thermo-elastic properties can be obtained. This suggests that next generation TPS properties can be accurately estimated via atomistically informed multiscale analysis.

  3. Size-Dependent Materials Properties Toward a Universal Equation

    Directory of Open Access Journals (Sweden)

    Guisbiers G

    2010-01-01

    Full Text Available Abstract Due to the lack of experimental values concerning some material properties at the nanoscale, it is interesting to evaluate this theoretically. Through a “top–down” approach, a universal equation is developed here which is particularly helpful when experiments are difficult to lead on a specific material property. It only requires the knowledge of the surface area to volume ratio of the nanomaterial, its size as well as the statistic (Fermi–Dirac or Bose–Einstein followed by the particles involved in the considered material property. Comparison between different existing theoretical models and the proposed equation is done.

  4. Broadband optical characterization of material properties

    DEFF Research Database (Denmark)

    Nielsen, Otto Højager Attermann

    , as well as details of the absorption spectrum which relate to chemical composition. The thesis focuses on two production process from the food industry. The first process is from the dairy industry where discrimination between chemical and structural properties is of importance. To explore...... inspection system for spectrallyresolved Static Light Scattering (SLS). (II) Photon Time-of-Flight (PToF) spectroscopy, which is a state of the art technique for characterization of turbid media. (III) A new hyperspectral imaging system based on full-field illumination by diffuse laser light. This thesis...... the fermentation process. It has also been shown that the optical inspection methods sense changes to structural properties before any are detected by traditional mechanical rheology. Finally, the developed hyperspectral imaging system was used to quantify the content of astaxanthin in fish feed, and performed...

  5. Mechanical Properties of Infrared Transmitting Materials

    Science.gov (United States)

    1978-01-01

    Theory of the Elasticity," 4th Edition, Dover Publ. Co., New York, N.Y., 1944. Marriott, J. B., and G. Rowden, "The Erosion of a Cobalt - Chromium Alloy...alumina (A1203), spinel (magnesium aluminate ), magnesia (MgO), yttria (Y203), as well as chemical vapor deposition (CVD) silicon carbide, CVD...known to be a problem. Because of their thermal and mechanical properties, alumina and magnesium aluminate (spinel) show, or can show, erosion

  6. Permittivity spectroscopy - an insight into materials properties.

    Science.gov (United States)

    Stoynov, Zdravko; Mladenova, Emiliya; Levi, Daniela; Vladikova, Daria

    2014-01-01

    Permittivity Spectroscopy is a branch of the Impedance Spectroscopy specially tuned for measurements and analyses of dielectrics permittivity properties. The present paper presents experimental results on permittivity properties of composite objects in which a polarizable dielectric is distributed in a fine non-polarizable matrix (solid or liquid) measured in frequency range 1 MHz down to 0.01 Hz. Two types of objects are studied - water in porous functional ceramics and lubricating oils. In both systems gigantic enhancement of the effective capacitance is observed. The first series of experiments was performed on porous membranes of yttrium doped barium cerate, which is a proton conducting ceramics with hydrophilic properties. At a given level of watering the measured capacitance is sharply increasing (3 to 5 orders of magnitude) in the lower frequency range. The second example covers permittivity study of lubricating oils, where the increase is 2-3 orders of magnitude. The phenomenon of gigantic enhancement of the effective capacitance could be related to a formation of dipole volume structures induced by the external alternating electrical field.

  7. Terahertz dynamic scanning reflectometry of soldier personal protective material

    Science.gov (United States)

    Rahman, Anis; Mentzer, Mark

    2012-02-01

    Ballistic characterization of improved materials for Soldier personal protective equipment is an ever-challenging task, requiring precise measurement of materials during ballistic impact. Current dynamic deformation technologies, such as high-speed digital image correlation, and laser velocimetry and vibrometry, are only able to provide surface measurements. However, there is a need to measure the dynamic delamination and mass loss of composite material, allowing calculation of available kinetic energy remaining in the material. A high sensitivity terahertz dynamic scanning reflectometer may be used to measure dynamic surface deformation and delamination characteristics in real-time. A number of crucial parameters can be extracted from the reflectance measurements such as dynamic deformation, propagation velocity, and final relaxation position. As proof of principle, an acrylic plate was struck with a blunt pendulum impactor and dynamic deformation was captured in real-time. Reflectance kinetics was converted to deformation and the velocity was calculated from the kinetics spectrum. Kinetics of a focused pendulum impactor on a steel plate was also acquired, characterizing plate relaxation from maximum deformation to equilibrium with discernible vibrations before reaching stable equilibrium.

  8. Thermal and Electrical Properties of Nanocomposites, Including Material Properties

    NARCIS (Netherlands)

    Kochetov, R.

    2012-01-01

    The research described in this thesis is part of a state-funded IOP-EMVT project in cooperation with industrial companies, aiming at the design, assessment and implementation of new, environmental friendly (e.g. oil and SF6 - free) solid dielectric materials. A large disadvantage of solid polymer di

  9. Thermal and Electrical Properties of Nanocomposites, Including Material Properties

    NARCIS (Netherlands)

    Kochetov, R.

    2012-01-01

    The research described in this thesis is part of a state-funded IOP-EMVT project in cooperation with industrial companies, aiming at the design, assessment and implementation of new, environmental friendly (e.g. oil and SF6 - free) solid dielectric materials. A large disadvantage of solid polymer

  10. Numerical simulations of granular dynamics II: Particle dynamics in a shaken granular material

    Science.gov (United States)

    Murdoch, Naomi; Michel, Patrick; Richardson, Derek C.; Nordstrom, Kerstin; Berardi, Christian R.; Green, Simon F.; Losert, Wolfgang

    2012-05-01

    Surfaces of planets and small bodies of our Solar System are often covered by a layer of granular material that can range from a fine regolith to a gravel-like structure of varying depths. Therefore, the dynamics of granular materials are involved in many events occurring during planetary and small-body evolution thus contributing to their geological properties. We demonstrate that the new adaptation of the parallel N-body hard-sphere code pkdgrav has the capability to model accurately the key features of the collective motion of bidisperse granular materials in a dense regime as a result of shaking. As a stringent test of the numerical code we investigate the complex collective ordering and motion of granular material by direct comparison with laboratory experiments. We demonstrate that, as experimentally observed, the scale of the collective motion increases with increasing small-particle additive concentration. We then extend our investigations to assess how self-gravity and external gravity affect collective motion. In our reduced-gravity simulations both the gravitational conditions and the frequency of the vibrations roughly match the conditions on asteroids subjected to seismic shaking, though real regolith is likely to be much more heterogeneous and less ordered than in our idealised simulations. We also show that collective motion can occur in a granular material under a wide range of inter-particle gravity conditions and in the absence of an external gravitational field. These investigations demonstrate the great interest of being able to simulate conditions that are to relevant planetary science yet unreachable by Earth-based laboratory experiments.

  11. STRUCTURE AND DYNAMICS OF POLYMERIC MATERIALS IN NANO-SCALE

    Institute of Scientific and Technical Information of China (English)

    Toshio Nishi; So Fujinami; Dong Wang; Hao Liu; Ken Nakajima

    2011-01-01

    The nano-palpation technique, i.e., nanometer-scale elastic and viscoelastic measurements based on atomic force microscope, is introduced. It is demonstrated to be very useful in analyzing nanometer-scale materials properties for the surfaces and interfaces of various types of soft materials. It enables us to obtain not only structural information but also mechanical information about a material at the same place and at the same time.

  12. Dynamical mean field theory-based electronic structure calculations for correlated materials.

    Science.gov (United States)

    Biermann, Silke

    2014-01-01

    We give an introduction to dynamical mean field approaches to correlated materials. Starting from the concept of electronic correlation, we explain why a theoretical description of correlations in spectroscopic properties needs to go beyond the single-particle picture of band theory.We discuss the main ideas of dynamical mean field theory and its use within realistic electronic structure calculations, illustrated by examples of transition metals, transition metal oxides, and rare-earth compounds. Finally, we summarise recent progress on the calculation of effective Hubbard interactions and the description of dynamical screening effects in solids.

  13. Probabilistic Modeling of Graded Timber Material Properties

    DEFF Research Database (Denmark)

    Faber, M. H.; Köhler, J.; Sørensen, John Dalsgaard

    2004-01-01

    The probabilistic modeling of timber material characteristics is considered with special emphasis to the modeling of the effect of different quality control and selection procedures used as means for quality grading in the production line. It is shown how statistical models may be established...... an important role in the overall probabilistic modeling. Therefore a scheme for estimating the parameters of probability distribution parameters focusing on the tail behavior has been established using a censored Maximum Likelihood estimation technique. The proposed probabilistic models have been formulated...

  14. Spectroscopic properties of rare earths in optical materials

    CERN Document Server

    Parisi, Jürgen; Osgood, R; Warlimont, Hans; Liu, Guokui; Jacquier, Bernard

    2005-01-01

    Aimed at researchers and graduate students, this book provides up-to-date information for understanding electronic interactions that impact the optical properties of rare earth ions in solids. Its goal is to establish a connection between fundamental principles and the materials properties of rare-earth activated luminescent and laser optical materials. The theoretical survey and introduction to spectroscopic properties include electronic energy level structure, intensities of optical transitions, ion-phonon interactions, line broadening, and energy transfer and up-conversion. An important aspect of the book lies in its deep and detailed discussions on materials properties and the potential of new applications such as optical storage, information processing, nanophotonics, and molecular probes that have been identified in recent experimental studies. This volume will be a valuable reference book on advanced topics of rare earth spectroscopy and materials science.

  15. Interdisciplinary research concerning the nature and properties of ceramic materials

    Science.gov (United States)

    1975-01-01

    The nature and properties of ceramic materials as they relate to solid state physics and metallurgy are studied. Special attention was given to the applications of ceramics to NASA programs and national needs.

  16. Outgassing Properties of Chemically Polished Titanium Materials

    Science.gov (United States)

    Kurisu, Hiroki; Kimoto, Gou; Fujii, Hiroaki; Tanaka, Kazuhiko; Yamamoto, Setsuo; Matsuura, Mitsuru; Ishizawa, Katsunobu; Nomura, Takeru; Murashige, Nobuyuki

    We developed a chemical polishing (CP) for titanium materials applicable to ultrahigh vacuum (UHV) and extremely high vacuum (XHV) systems. The surface roughness, Ra, of the chemically polished titanium is obtained to be 25 nm by the atomic force microscopy measurement. This value is smaller than those of the base metal (BM) and the buff-polished (BP) samples. The thickness of the surface oxide layer of CP sample is estimated to be 7 nm by the cross section of transmission electron micrograph. Amount of desorption gas of CP sample obtained by the thermal desorption measurement is smaller than those of BM and BP sample, and is the same as that of the mechanochemically polished (MCP) sample. The outgassing rate of CP sample after baking at 150°C×20 h is obtained to be 7×10-13 Pa•m•s-1. This value is lower than that of standard vacuum materials by two orders of magnitude after the ordinary baking.

  17. Transport properties of colossal magnetoresistive materials

    CERN Document Server

    Yates, K A

    2002-01-01

    A microwave technique was developed in order to test the validity of the hypothesis that the microwave transport of polycrystalline, optimally doped, colossal magnetoresistive materials was dominated by intragranular material. The microwave surface resistance at 9GHz was compared with dc resistivity and magnetisation to study the influence of yttrium doping on the grain boundary regions of bulk polycrystalline samples of La sub 0 sub . sub 7 sub - sub x Y sub x Ca sub 0 sub . sub 3 MnO sub 3. It was found that, within the grains, the addition of yttrium causes the activation energy above T sub p to increase. A phenomenological model was introduced to explain the data in terms of the difference in structure between the grain and grain boundary regions. The technique was also used to study the influence of deoxygenation on the grain boundary regions of bulk, polycrystalline, La sub 0 sub . sub 6 sub 7 Ca sub 0 sub . sub 3 sub 3 MnO sub 3. For samples interconnected porosity, low temperature (600 deg C), short a...

  18. MIDAS (Material Implementation, Database, and Analysis Source): A comprehensive resource of material properties

    Energy Technology Data Exchange (ETDEWEB)

    Tang, M; Norquist, P; Barton, N; Durrenberger, K; Florando, J; Attia, A

    2010-12-13

    MIDAS is aimed to be an easy-to-use and comprehensive common source for material properties including both experimental data and models and their parameters. At LLNL, we will develop MIDAS to be the central repository for material strength related data and models with the long-term goal to encompass other material properties. MIDAS will allow the users to upload experimental data and updated models, to view and read materials data and references, to manipulate models and their parameters, and to serve as the central location for the application codes to access the continuously growing model source codes. MIDAS contains a suite of interoperable tools and utilizes components already existing at LLNL: MSD (material strength database), MatProp (database of materials properties files), and MSlib (library of material model source codes). MIDAS requires significant development of the computer science framework for the interfaces between different components. We present the current status of MIDAS and its future development in this paper.

  19. A Reference Guide for Cryogenic Properties of Materials

    Energy Technology Data Exchange (ETDEWEB)

    Weisend, John G

    2003-09-16

    A thorough knowledge of the behavior of materials at cryogenic temperatures is critical for the design of successful cryogenic systems. Over the past 50 years, a tremendous amount of material properties at cryogenic temperatures have been measured and published. This guide lists resources for finding these properties. It covers online databases, computer codes, conference proceedings, journals, handbooks, overviews and monographs. It includes references for finding reports issued by government laboratories and agencies. Most common solids and fluids used in cryogenics are covered.

  20. Cellular and Porous Materials Thermal Properties Simulation and Prediction

    CERN Document Server

    Öchsner, Andreas; de Lemos, Marcelo J S

    2008-01-01

    Providing the reader with a solid understanding of the fundamentals as well as an awareness of recent advances in properties and applications of cellular and porous materials, this handbook and ready reference covers all important analytical and numerical methods for characterizing and predicting thermal properties. In so doing it directly addresses the special characteristics of foam-like and hole-riddled materials, combining theoretical and experimental aspects for characterization purposes.

  1. INVESTIGATION OF TRIBOLOGICAL PROPERTIES CuSn10 BEARING MATERIAL

    OpenAIRE

    2005-01-01

    Bronzes which copper based alloys is widely used because of properties physical, thermal and tribological as journal bearing material. This material that has tribological performance good conclusions gives at journal bearings. In this study, CuSn10 bronze that were manufactured journal bearings friction and wear properties has been examined and compared. SAE 1050 steel shaft has been used as counter abrader. Experiments have been carried out 10 N and 20 N loads, 750 and 1500 rpm, dry and lubr...

  2. X-ray Birefringence Imaging of Materials with Anisotropic Molecular Dynamics.

    Science.gov (United States)

    Palmer, Benjamin A; Edwards-Gau, Gregory R; Kariuki, Benson M; Harris, Kenneth D M; Dolbnya, Igor P; Collins, Stephen P; Sutter, John P

    2015-02-05

    The X-ray birefringence imaging (XBI) technique, reported very recently, is a sensitive tool for spatially resolved mapping of the local orientational properties of anisotropic materials. In this paper, we report the first XBI measurements on materials that undergo anisotropic molecular dynamics. Using incident linearly polarized X-rays with energy close to the Br K-edge, the X-ray birefringence is dictated by the orientational properties of the C-Br bonds in the material. We focus on two materials (urea inclusion compounds containing 1,8-dibromooctane and 1,10-dibromodecane guest molecules) for which the reorientational dynamics of the brominated guest molecules (and hence the reorientational dynamics of the C-Br bonds) are already well characterized by other experimental techniques. The XBI results demonstrate clearly that, for the anisotropic molecular dynamics in these materials, the effective X-ray optic axis for the X-ray birefringence phenomenon is the time-averaged resultant of the orientational distribution of the C-Br bonds.

  3. PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

    OpenAIRE

    2014-01-01

    Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstruct...

  4. Dynamic Characterization and Modeling of Potting Materials for Electronics Assemblies

    Science.gov (United States)

    Joshi, Vasant; Lee, Gilbert; Santiago, Jaime

    2015-06-01

    Prediction of survivability of encapsulated electronic components subject to impact relies on accurate modeling. Both static and dynamic characterization of encapsulation material is needed to generate a robust material model. Current focus is on potting materials to mitigate high rate loading on impact. In this effort, encapsulation scheme consists of layers of polymeric material Sylgard 184 and Triggerbond Epoxy-20-3001. Experiments conducted for characterization of materials include conventional tension and compression tests, Hopkinson bar, dynamic material analyzer (DMA) and a non-conventional accelerometer based resonance tests for obtaining high frequency data. For an ideal material, data can be fitted to Williams-Landel-Ferry (WLF) model. A new temperature-time shift (TTS) macro was written to compare idealized temperature shift factor (WLF model) with experimental incremental shift factors. Deviations can be observed by comparison of experimental data with the model fit to determine the actual material behavior. Similarly, another macro written for obtaining Ogden model parameter from Hopkinson Bar tests indicates deviations from experimental high strain rate data. In this paper, experimental results for different materials used for mitigating impact, and ways to combine data from resonance, DMA and Hopkinson bar together with modeling refinements will be presented.

  5. Magnetic Properties of Nanoparticles of Antiferromagnetic Materials

    DEFF Research Database (Denmark)

    Mørup, Steen; Frandsen, Cathrine; Bødker, Franz

    2003-01-01

    The magnetic properties of antiferromagnetic nanoparticles have been studied by Mossbauer spectroscopy and neutron scattering. Temperature series of Mossbauer spectra of non-interacting, superparamagnetic hematite nanoparticles were fitted by use of the Blume-Tjon relaxation model. It has been...... found that the magnetic anisotropy energy constant increases significantly with decreasing particle size. Neutron scattering experiments on similar samples give new information on both superparamagnetic relaxation and collective magnetic excitations. There is good agreement between the values...... of the parameters obtained from Mossbauer spectroscopy and neutron scattering. In samples of interacting hematite nanoparticles, the relaxation was significantly suppressed. The Mossbauer data for these samples are in accordance with a mean field model for an ordered state of strongly interacting particles. Mixing...

  6. Surface properties of copper based cermet materials

    Energy Technology Data Exchange (ETDEWEB)

    Voinea, M. [The Centre: Product Design for Sustainable Development, Transilvania University of Brasov, Eroilor 29, 500036 (Romania)], E-mail: m.voinea@unitbv.ro; Vladuta, C.; Bogatu, C.; Duta, A. [The Centre: Product Design for Sustainable Development, Transilvania University of Brasov, Eroilor 29, 500036 (Romania)

    2008-08-25

    The paper presents the characterization of the surface properties of copper based cermets obtained by two different techniques: spray pyrolysis deposition (SPD) and electrodeposition. Copper acetate was used as precursor of Cu/CuO{sub x} cermet. The surface morphology was tailored by adding copolymers of maleic anhydride with controlled hydrophobia. The films morphology of Cu/CuO{sub x} was assessed using contact angle measurements and AFM analysis. The porous structures obtained via SPD lead to higher liquid adsorption rate than the electrodeposited films. A highly polar liquid - water is recommended as testing liquid in contact angle measurements, for estimating the porosity of copper based cermets, while glycerol can be used to distinguish among ionic and metal predominant structures. Thus, contact angle measurements can be used for a primary evaluation of the films morphology and, on the other hand, of the ratio between the cermet components.

  7. Analytic Thermoelectric Couple Modeling: Variable Material Properties and Transient Operation

    Science.gov (United States)

    Mackey, Jonathan A.; Sehirlioglu, Alp; Dynys, Fred

    2015-01-01

    To gain a deeper understanding of the operation of a thermoelectric couple a set of analytic solutions have been derived for a variable material property couple and a transient couple. Using an analytic approach, as opposed to commonly used numerical techniques, results in a set of useful design guidelines. These guidelines can serve as useful starting conditions for further numerical studies, or can serve as design rules for lab built couples. The analytic modeling considers two cases and accounts for 1) material properties which vary with temperature and 2) transient operation of a couple. The variable material property case was handled by means of an asymptotic expansion, which allows for insight into the influence of temperature dependence on different material properties. The variable property work demonstrated the important fact that materials with identical average Figure of Merits can lead to different conversion efficiencies due to temperature dependence of the properties. The transient couple was investigated through a Greens function approach; several transient boundary conditions were investigated. The transient work introduces several new design considerations which are not captured by the classic steady state analysis. The work helps to assist in designing couples for optimal performance, and also helps assist in material selection.

  8. Solder joint technology materials, properties, and reliability

    CERN Document Server

    Tu, King-Ning

    2007-01-01

    Solder joints are ubiquitous in electronic consumer products. The European Union has a directive to ban the use of Pb-based solders in these products on July 1st, 2006. There is an urgent need for an increase in the research and development of Pb-free solders in electronic manufacturing. For example, spontaneous Sn whisker growth and electromigration induced failure in solder joints are serious issues. These reliability issues are quite complicated due to the combined effect of electrical, mechanical, chemical, and thermal forces on solder joints. To improve solder joint reliability, the science of solder joint behavior under various driving forces must be understood. In this book, the advanced materials reliability issues related to copper-tin reaction and electromigration in solder joints are emphasized and methods to prevent these reliability problems are discussed.

  9. Liquid Crystalline Semiconductors Materials, properties and applications

    CERN Document Server

    Kelly, Stephen; O'Neill, Mary

    2013-01-01

    This is an exciting stage in the development of organic electronics. It is no longer an area of purely academic interest as increasingly real applications are being developed, some of which are beginning to come on-stream. Areas that have already been commercially developed or which are under intensive development include organic light emitting diodes (for flat panel displays and solid state lighting), organic photovoltaic cells, organic thin film transistors (for smart tags and flat panel displays) and sensors. Within the family of organic electronic materials, liquid crystals are relative newcomers. The first electronically conducting liquid crystals were reported in 1988 but already a substantial literature has developed. The advantage of liquid crystalline semiconductors is that they have the easy processability of amorphous and polymeric semiconductors but they usually have higher charge carrier mobilities. Their mobilities do not reach the levels seen in crystalline organics but they circumvent all of t...

  10. Electrical and optoelectronic properties of two-dimensional materials

    Science.gov (United States)

    Wang, Qiaoming

    Electrical and optoelectronic properties of bulk semiconductor materials have been extensively explored in last century. However, when reduced to one-dimensional and two-dimensional, many semiconductors start to show unique electrical and optoelectronic behaviors. In this dissertation, electrical and optoelectronic properties of one-dimensional (nanowires) and two-dimensional semiconductor materials are investigated by various techniques, including scanning photocurrent microscopy, scanning Kelvin probe microscopy, Raman spectroscopy, photoluminescence, and finite-element simulations. In our work, gate-tunable photocurrent in ZnO nanowires has been observed under optical excitation in the visible regime, which originates from the nanowire/substrate interface states. This gate tunability in the visible regime can be used to enhance the photon absorption efficiency, and suppress the undesirable visible-light photodetection in ZnO-based solar cells. The power conversion efficiency of CuInSe2/CdS core-shell nanowire solar cells has been investigated. The highest power conversion efficiency per unit area/volume is achieved with core diameter of 50 nm and the thinnest shell thickness. The existence of the optimal geometrical parameters is due to a combined effect of optical resonances and carrier transport/dynamics. Significant current crowding in two-dimensional black phosphorus field-effect transistors has been found, which has been significantly underestimated by the commonly used transmission-line model. This current crowding can lead to Joule heating close to the contacts. New van der Waals metal-semiconductor junctions have been mechanically constructed and systematically studied. The photocurrent on junction area has been demonstrated to originate from the photothermal effect rather than the photovoltaic effect. Our findings suggest that a reasonable control of interface/surface state properties can enable new and beneficial functionalities in nanostructures. We

  11. Computational evaluation of optoelectronic properties for organic/carbon materials.

    Science.gov (United States)

    Shuai, Zhigang; Wang, Dong; Peng, Qian; Geng, Hua

    2014-11-18

    CONSPECTUS: Organic optoelectronic materials are used in a variety of devices, including light-emitting diodes, field-effect transistors, photovoltaics, thermoelectrics, spintronics, and chemico- and biosensors. The processes that determine the intrinsic optoelectronic properties occur either in the photoexcited states or within the electron-pumped charged species, and computations that predict these optical and electrical properties would help researchers design new materials. In this Account, we describe recent advances in related density functional theory (DFT) methods and present case studies that examine the efficiency of light emission, carrier mobility, and thermoelectric figures of merit by calculation of the electron-vibration couplings. First we present a unified vibrational correlation function formalism to evaluate the excited-state radiative decay rate constant kr, the nonradiative decay rate constant knr, the intersystem crossing rate constant kISC, and the optical spectra. The molecular parameters that appear in the formalism, such as the electronic excited-state energy, vibrational modes, and vibronic couplings, require extensive DFT calculations. We used experiments for anthracene at both low and ambient temperatures to benchmark the calculated photophysical parameters. In the framework of Fermi's golden rule, we incorporated the non-adiabatic coupling and the spin-orbit coupling to evaluate the phosphorescence efficiency and emission spectrum. Both of these are in good agreement with experimental results for anthracene and iridium compounds. Band electron scattering and relaxation processes within Boltzmann theory can describe charge transport in two-dimensional carbon materials and closely packed organic solids. For simplicity, we considered only the acoustic phonon scattering as modeled by the deformation potential approximation coupled with extensive DFT calculations for band structures. We then related the carrier mobility to the band

  12. Dynamic Materials do the Trick in Participatory Business Modeling

    DEFF Research Database (Denmark)

    Caglio, Agnese; Buur, Jacob

    In this position paper we suggest that design material with dynamic behaviour is particularly suited to scaffold groups of diverse participants in discussing the ‘if – then’ causalities of business models. Based on video data from a number of innovation project workshops we present a comparison m...... matrix of five different material types for participatory business modeling. The comparison matrix highlights patterns in the use of materials, and how they allow people to participate, negotiate and make meaning.......In this position paper we suggest that design material with dynamic behaviour is particularly suited to scaffold groups of diverse participants in discussing the ‘if – then’ causalities of business models. Based on video data from a number of innovation project workshops we present a comparison...

  13. The design and modeling of periodic materials with novel properties

    Science.gov (United States)

    Berger, Jonathan Bernard

    Cellular materials are ubiquitous in our world being found in natural and engineered systems as structural materials, sound and energy absorbers, heat insulators and more. Stochastic foams made of polymers, metals and even ceramics find wide use due to their novel properties when compared to monolithic materials. Properties of these so called hybrid materials, those that combine materials or materials and space, are derived from the localization of thermomechanical stresses and strains on the mesoscale as a function of cell topology. The effects of localization can only be generalized in stochastic materials arising from their inherent potential complexity, possessing variations in local chemistry, microstructural inhomogeneity and topological variations. Ordered cellular materials on the other hand, such as lattices and honeycombs, make for much easier study, often requiring analysis of only a single unit-cell. Theoretical bounds predict that hybrid materials have the potential to push design envelopes offering lighter stiffer and stronger materials. Hybrid materials can achieve very low and even negative coefficients of thermal expansion (CTE) while retaining a relatively high stiffness -- properties completely unmatched by monolithic materials. In the first chapter of this thesis a two-dimensional lattice is detailed that possess near maximum stiffness, relative to the tightest theoretical bound, and low, zero and even appreciably negative thermal expansion. Its CTE and stiffness are given in closed form as a function of geometric parameters and the material properties. This result is confirmed with finite elements (FE) and experiment. In the second chapter the compressive stiffness of three-dimensional ordered foams, both closed and open cell, are predicted with FE and the results placed in property space in terms of stiffness and density. A novel structure is identified that effectively achieves theoretical bounds for Young's, shear and bulk modulus

  14. Materials Selection, Synthesis, and Dielectrical Properties of PVC Nanocomposites

    OpenAIRE

    Youssef Mobarak; Bassyouni, M.; Almutawa, M.

    2013-01-01

    Materials selection process for electrical insulation application was carried out using Cambridge Engineering Selector (CES) program. Melt mixing technique was applied to prepare polyvinyl-chloride- (PVC-) nanofumed silica and nanomontmorillonite clay composites. Surface analysis and particles dispersibility were examined using scanning electron microscope. Dielectrical properties were assessed using Hipot tester. An experimental work for dielectric loss of the nanocomposite materials has bee...

  15. Understanding Materials Science History · Properties · Applications

    CERN Document Server

    Hummel, Rolf E

    2005-01-01

    This introduction to materials science both for students of engineering and physics and for the interested general public examines not only the physical and engineering properties of virtually all kinds of materials, but also their history, uses, development, and some of the implications of resource depletion and recycling. It covers all topics on materials from an entirely novel perspective: the role materials have played throughout history in the development of humankind and technologies. Specifically, it shows the connection between the technical and the cultural, economic, ecological, and societal aspects of materials science. It aims to whet the appetite of its readers and inspire them to further explore the properties and applications of metals, alloys, ceramics, plastics, and electronic materials by presenting easily understandable explanations and entertaining historical facts. It is also intended to raise the reader’s awareness of their obligations to society as practicing engineers and scientists....

  16. Finite Element Method for Analysis of Material Properties

    DEFF Research Database (Denmark)

    Rauhe, Jens Christian

    The use of cellular and composite materials have in recent years become more and more common in all kinds of structural components and accurate knowledge of the effective properties is therefore essential. In this wok the effective properties are determined using the real material microstructure...... and the finite element method. The material microstructure of the heterogeneous material is non-destructively determined using X-ray microtomography. A software program has been generated which uses the X-ray tomographic data as an input for the mesh generation of the material microstructure. To obtain a proper...... description of the material microstructure the finite element models must contain a large number of elements and this problem is solved by using the preconditioned conjugated gradient solver with an Element-By-Element preconditioner. Finite element analysis provides the volume averaged stresses and strains...

  17. Design of Ordered Wrinkled Patterns with Dynamically Tuned Properties

    Science.gov (United States)

    Yagüe, Jose Luis; Yin, Jie; Boyce, Mary C.; Gleason, Karen K.

    The formation of patterned surfaces is a common tool to engineer materials. The capability to design and reproduce detailed features is a key factor to fulfill requirements for functional surfaces. Generation of wrinkles via buckling of a stiff film on a compliant surface is an inexpensive, easy and reliable method to yield a patterned surface. The wrinkling method has been exploited in a wide variety of areas, including photovoltaics, microfluidics, adhesion, and anti-fouling systems. Here we show the ability to obtain deterministically ordered herringbone patterns. In a biaxially pre-stretched PDMS sample a thin film of a stiff coating is deposited by initiated chemical vapor deposition (iCVD). iCVD is a solvent- free technique that yields a conformal thin coating on virtually any substrate, giving a controllable thickness and tunable structural, mechanical, thermal, wetting, and swelling properties. Sequential release of the film-substrate system shows the transition from 1-D ripples to an ordered herringbone pattern. Wrinkle features can be controlled adjusting the film thickness, the initial load and the release process. Moreover, the surface topography can be dynamically tuned by applying a controlled mechanical stimulus. These properties make these materials excellent candidates for flexible applications.

  18. OM85. Basic Properties of Optical Materials Summaries of Papers.

    Science.gov (United States)

    1985-05-01

    Optical Properties of Solids (Academic, New York, 1972) Ch.3. 7. D.B. Tanner, A.J...12, (1973). 6. T. Fleisch and R. Abermann, Thin Solid FilffF-42, 255-263 (1977). 7. F. Wooten, Optical Properties of Solids (Academic Press, New York...resolve cp structure. Such mea- surements are still lacking for many common semiconducting materials. REFERENCES 1. D.E. Aspnes, in Optical Properties of Solids :

  19. Thermodynamical and dynamical properties of charged BTZ black holes

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Zi-Yu; Wang, Bin [Shanghai Jiao Tong University, Department of Physics and Astronomy, Center for Astronomy and Astrophysics, Shanghai (China); Zhang, Cheng-Yong [Peking University, Center for High-Energy Physics, Beijing (China); Kord Zangeneh, Mahdi [Shanghai Jiao Tong University, Department of Physics and Astronomy, Center for Astronomy and Astrophysics, Shanghai (China); Shahid Chamran University of Ahvaz, Physics Department, Faculty of Science, Ahvaz (Iran, Islamic Republic of); Research Institute for Astronomy and Astrophysics of Maragha (RIAAM)-Maragha, P. O. Box: 55134-441, Maragha (Iran, Islamic Republic of); Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Saavedra, Joel [Pontificia Universidad Catolica de Valparaiso, Instituto de Fisica, Valparaiso (Chile)

    2017-06-15

    We investigate the spacetime properties of BTZ black holes in the presence of the Maxwell field and Born-Infeld field and find rich properties in the spacetime structures when the model parameters are varied. Employing Landau-Lifshitz theory, we examine the thermodynamical phase transition in the charged BTZ black holes. We further study the dynamical perturbation in the background of the charged BTZ black holes and find different properties in the dynamics when the thermodynamical phase transition occurs. (orig.)

  20. Structural Properties of Concrete Materials Containing RoadCem

    Directory of Open Access Journals (Sweden)

    Niall Holmes

    2015-01-01

    Full Text Available This paper presents findings from a preliminary study to assess the structural and material properties of a nonstandard, concrete type mix containing RoadCem, a traditional soil stabilising additive. Two different mixes determined the effect of adding RoadCem in terms of compressive and flexural strengths, breaking strain, thermal expansion and contraction behaviour, permeability using a falling head, and Young’s modulus. RoadCem is a fine powder containing alkali metals and synthetic zeolites which are complemented with a complex activator. RoadCem modifies the dynamics and chemistry of cement hydration by enhancing the crystallisation process and forming longer needle crystalline structures. It reduces the heat of hydration with an early strength development. Varying the volume in the mix varies the viscosity and alters curing times while maintaining the water cement ratio. The results from this study have shown a modest increase in compressive strength and Young’s modulus with improvements in thermal performance, particularly at low temperatures. The flexural strength of the two mixes was similar with a much reduced permeability in the RoadCem mix. The results demonstrate the improved performance of concrete incorporating RoadCem but further improvements are possible by using a better graded aggregate and controlling the maximum dry density and moisture contents.

  1. Static and Dynamic Properties of Semi-Crystalline Polyethylene

    Directory of Open Access Journals (Sweden)

    Ming-ming Xu

    2016-03-01

    Full Text Available Properties of extruded polymers are strongly affected by molecular structure. For two different semi-crystalline polymers, low-density polyethylene (LDPE and ultra-high molecular weight polyethylene (UHMWPE, this investigation measures the elastic modulus, plastic flow stress and strain-rate dependence of yield stress. Also, it examines the effect of molecular structure on post-necking tensile fracture. The static and dynamic material tests reveal that extruded UHMWPE has a somewhat larger yield stress and much larger strain to failure than LDPE. For both types of polyethylene, the strain at tensile failure decreases with increasing strain-rate. For strain-rates 0.001–3400 s−1, the yield stress variation is accurately represented by the Cowper–Symonds equation. These results indicate that, at high strain rates, UHMWPE is more energy absorbent than LDPE as a result of its long chain molecular structure with few branches.

  2. Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing

    Science.gov (United States)

    Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs

    2017-04-01

    The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.

  3. Grain size dependent mechanical properties in nanophase materials

    Energy Technology Data Exchange (ETDEWEB)

    Siegel, R.W. [Argonne National Lab., IL (United States); Fougere, G.E. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering

    1995-02-01

    It has become possible in recent years to synthesize metals and ceramics under well controlled conditions with constituent grain structures on a manometer size scale (below 100 nm). These new materials have mechanical properties that are strongly grain-size dependent and often significantly different than those of their coarser grained counterparts. Nanophase metals tend to become stronger and ceramics are more easily deformed as grain size is reduced. The observed mechanical property changes appear to be related primarily to grain size limitations and the large percentage of atoms in grain boundary environments. A brief overview of our present knowledge about the grain-size dependent mechanical properties of nanophase materials is presented.

  4. Hyperelastic Material Properties of Mouse Skin under Compression.

    Directory of Open Access Journals (Sweden)

    Yuxiang Wang

    Full Text Available The skin is a dynamic organ whose complex material properties are capable of withstanding continuous mechanical stress while accommodating insults and organism growth. Moreover, synchronized hair cycles, comprising waves of hair growth, regression and rest, are accompanied by dramatic fluctuations in skin thickness in mice. Whether such structural changes alter skin mechanics is unknown. Mouse models are extensively used to study skin biology and pathophysiology, including aging, UV-induced skin damage and somatosensory signaling. As the skin serves a pivotal role in the transfer function from sensory stimuli to neuronal signaling, we sought to define the mechanical properties of mouse skin over a range of normal physiological states. Skin thickness, stiffness and modulus were quantitatively surveyed in adult, female mice (Mus musculus. These measures were analyzed under uniaxial compression, which is relevant for touch reception and compression injuries, rather than tension, which is typically used to analyze skin mechanics. Compression tests were performed with 105 full-thickness, freshly isolated specimens from the hairy skin of the hind limb. Physiological variables included body weight, hair-cycle stage, maturity level, skin site and individual animal differences. Skin thickness and stiffness were dominated by hair-cycle stage at young (6-10 weeks and intermediate (13-19 weeks adult ages but by body weight in mature mice (26-34 weeks. Interestingly, stiffness varied inversely with thickness so that hyperelastic modulus was consistent across hair-cycle stages and body weights. By contrast, the mechanics of hairy skin differs markedly with anatomical location. In particular, skin containing fascial structures such as nerves and blood vessels showed significantly greater modulus than adjacent sites. Collectively, this systematic survey indicates that, although its structure changes dramatically throughout adult life, mouse skin at a given

  5. Tunneling properties of electromagnetic wave in slab superconducting material

    Institute of Scientific and Technical Information of China (English)

    Khem B. Thapa; Sanjay Srivastava; Alka Vishwakarma; S. P. Ojha

    2011-01-01

    When the electromagnetic wave propagates through a slab superconducting material in microwave ranges, tunneling properties of the electromagnetic wave at critical temperature are investigated theoretically. The transmittance and the reflectance of the slab superconducting material vary with the thickness of material as well as the refractive index of substrates.The high transmittance is found for thin superconductor at low wavelength region.However, optical properties are strongly dependent upon temperature and incidence wavelength. The electromagnetic wave is totally transmitted without loss for incidence wavelength (λ = 5000 nm) due to the zero refractive index and infinite penetration depth of the superconductor at the critical temperature.

  6. Compact rock material gas permeability properties

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

    2014-09-15

    Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

  7. SEWABILITY PROPERTIES OF GARMENT LEATHERS TANNED WITH VARIOUS TANNING MATERIALS

    Directory of Open Access Journals (Sweden)

    ORK Nilay

    2016-05-01

    Full Text Available Chromium tannage is the most used technology in processing of garment leathers. Due to environmental requirements and demands on natural products there is an increasing interest on alternatives to chromium tannage especially on vegetable tanned leathers. Leather properties vary in a very wide range depending on the animal type it is obtained from and the process type and chemicals used in the manufacturing. In this study, the effect of various tanning materials to the sewability of garment leathers was investigated. For this purpose, vegetable, chromium and chromium-vegetable combination tanned garment leathers from the same animal origin were supplied from a garment leather manufacturing factory. Needle penetration force and the sewability values of these leathers were determined by using L&M Sewability Tester. It was found that material properties and sewing properties showed differences regarding to the tanning material used even in same type of raw material. Chromium tanned leathers had sewability values of 13.4% horizontal and 14.2% vertical which are considered good to fair. Vegetable tanned leathers and chromium-vegetable tanned leathers had sewability values of 38.2% horizontal, 49.2% vertical and 98% horizontal, 98.5% vertical respectively which are considered poor. The results of the study conclude that, there is a big difference in material properties when the tanning technology and material is changed which also affects the sewing properties.

  8. High Temperature Thermoelectric Properties of ZnO Based Materials

    DEFF Research Database (Denmark)

    Han, Li

    This thesis investigated the high temperature thermoelectric properties of ZnO based materials. The investigation first focused on the doping mechanisms of Al-doped ZnO, and then the influence of spark plasma sintering conditions on the thermoelectric properties of Al, Ga-dually doped ZnO....... Following that, the nanostructuring effect for Al-doped ZnO was systematically investigated using samples with different microstructure morphologies. At last, the newly developed ZnCdO materials with superior thermoelectric properties and thermal stability were introduced as promising substitutions...... for conventional ZnO materials. For Al-doped ZnO, α- and γ-Al2O3 were selectively used as dopants in order to understand the doping mechanism of each phase and their effects on the thermoelectric properties. The samples were prepared by the spark plasma sintering technique from precursors calcined at various...

  9. Understanding and Predicting the Properties of Complex Materials

    DEFF Research Database (Denmark)

    Smedskjær, Morten Mattrup; Mauro, John C.; Yue, Yuanzheng

    Predicting the properties of new materials prior to manufacturing is a topic attracting great industrial and scientific interest. Mechanical properties are currently of particular interest given the increasing demand for stronger, thinner, and more flexible materials in recent years. Property...... prediction for ceramic materials is facilitated by the periodic short- and long-range order of crystals. Based on J.C. Phillips’s theory for the ionicity of chemical bonding from ~1970, a method for predicting the hardness of covalent crystals was developed in the 2000s, which is now widely applied...... for the design of new superhard ceramic materials. It took another 10 years before the same predictions became possible for glassy systems, in which the lack of long-range order and the long time scales for relaxation greatly complicate the traditional modeling efforts. The key for making progress was to extract...

  10. Grafting Dynamics, Structures and Properties of Nano TiO2-SA Photocatalytic Materials%TiO2-SA纳米光催化材料接枝动力学、结构及性能

    Institute of Scientific and Technical Information of China (English)

    张巧玲; 李磊; 刘有智; 魏冰; 郭加欣; 冯玉杰

    2015-01-01

    Salicylic acid (SA) was successful y grafted onto nano-TiO2 surfaces (TiO2-SA) by post-treatment surface modification. The effects of ultrasound stiring, solvents, material ratio, pH value, and temperature on the grafting process and photocatalytic material properties were investigated, and the grafting reaction kinetics was determined. The structures of the materials were determined using Fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). A structural model was proposed. The properties of the photocatalytic material were examined using contact angle analysis, simultaneous thermogravimetry-differential scanning calorimetry (TG-DSC), ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS), and scanning electron microscopy (SEM). Compared with bare TiO2, the modified TiO2 had good hydrophobicity and dispersion properties, a lower sedimentation velocity in solvents, better adsorption stability at oil-water interfaces, and extended visible light absorption. The TiO2-SA gave excel ent photocatalytic performances in nitrobenzene degradation under ultraviolet-light irradiation.%采用后处理表面改性法在纳米TiO2表面接枝水杨酸(SA)(TiO2-SA),分别考察了超声搅拌、溶剂、物料比、pH值及温度等因素对接枝过程及光催化材料性能的影响,并研究了接枝反应动力学。通过傅里叶变换红外(FT-IR)光谱、X射线光电子能谱(XPS)、X射线衍射(XRD)等对TiO2-SA纳米光催化材料进行了结构表征,并提出了结构模型。通过接触角测定、同步热分析(热重-差示扫描量热法(TG-DSC))、紫外-可见漫反射光谱(UV-Vis DRS)、扫描电子显微镜(SEM)对光催化材料进行了性能表征。结果表明,水杨酸改性纳米TiO2可以提高疏水性及分散性,减缓在溶剂中的沉降速度,并能稳定吸附在油-水界面,实现了光谱响应范围向可见光的拓

  11. Effect of material uncertainties on dynamic response of segmental box girder bridge

    Directory of Open Access Journals (Sweden)

    Suchart Limkatanyu

    2007-11-01

    Full Text Available The main objective of this paper was to investigate the effect of material uncertainties on dynamic response of segmental box girder bridge subjected to a moving load, in this case a rapid passing trains. Literatures concerned with the design of segmental box girder bridge, the application of finite element analysis to model the segmental box girder bridge, and the minimum requirement for structural conditions of the bridge were described and discussed in detail. A series of finite element analysis was carried out using SAP2000 Nonlinear software. The effect was investigated by varying the Modulus of Elasticity by 5%, 10% and 15%. The results were then compared with the case of assumed uniform property which had already been checked for model accuracy using the Standard prEN 1991-2. The results showed that, for the uniform case, the dynamic responses of the bridge gave the highest response at the resonance speed. When considering the non-uniform material properties (non-uniform case, the effect of material uncertainties appeared to have an effect on both displacement and acceleration responses. Nonetheless, the dynamic factor provided in the design code was sufficient for designing the segmental box girder bridge with either uniform or non-uniform material properties for the train speeds considered in this study.

  12. Dielectric properties of tissues and biological materials: a critical review.

    Science.gov (United States)

    Foster, K R; Schwan, H P

    1989-01-01

    We critically review bulk electrical properties of tissues and other biological materials, from DC to 20 GHz, with emphasis on the underlying mechanisms responsible for the properties. We summarize the classical principles behind dielectric relaxation and critically review recent developments in this field. Special topics include a summary of the significant recent advances in theories of counterion polarization effects, dielectric properties of cancer vs. normal tissues, properties of low-water-content tissues, and macroscopic field-coupling considerations. Finally, the dielectric properties of tissues are summarized as empirical correlations with tissue water content in other compositional variables; in addition, a comprehensive table is presented of dielectric properties. The bulk electrical properties of tissues are needed for many bioengineering applications of electric fields or currents, and they provide insight into the basic mechanisms that govern the interaction of electric fields with tissue.

  13. Investigation of thermal properties of raw materials of asphalt mixtures

    Science.gov (United States)

    Géber, R.; Simon, A.; Kocserha, I.

    2017-02-01

    Asphalt mixtures are composite materials, which are made of different grades of mineral aggregates and bitumen. During the mixing process mineral materials were blended with bitumen at relatively high temperature (∼200 °C). As the binding process come off in these higher temperature range, thermal properties of asphaltic materials are important. The aim of this project is to reveal the thermal properties of raw materials. During our research two types of mineral aggregates were tested (limestone and dolomite) by different methods. Differential thermal analysis, thermal expansion and thermal conductivity were investigated at technologically important temperatures. The results showed that the structure of mineral materials did not change at elevated temperatures, expansion of samples was neglible, while thermal conductivity changed by temperature.

  14. A Summary of the Fatigue Properties of Wind Turbine Materials

    Energy Technology Data Exchange (ETDEWEB)

    SUTHERLAND, HERBERT J.

    1999-10-07

    Modern wind turbines are fatigue critical machines that are typically used to produce electrical power from the wind. The materials used to construct these machines are subjected to a unique loading spectrum that contains several orders of magnitude more cycles than other fatigue critical structures, e.g., an airplane. To facilitate fatigue designs, a large database of material properties has been generated over the past several years that is specialized to materials typically used in wind turbines. In this paper, I review these fatigue data. Major sections are devoted to the properties developed for wood, metals (primarily aluminum) and fiberglass. Special emphasis is placed on the fiberglass discussion because this material is current the material of choice for wind turbine blades. The paper focuses on the data developed in the U.S., but cites European references that provide important insights.

  15. Thermal properties of graphene and nanostructured carbon materials

    Science.gov (United States)

    Balandin, Alexander A.

    2011-08-01

    Recent years have seen a rapid growth of interest by the scientific and engineering communities in the thermal properties of materials. Heat removal has become a crucial issue for continuing progress in the electronic industry, and thermal conduction in low-dimensional structures has revealed truly intriguing features. Carbon allotropes and their derivatives occupy a unique place in terms of their ability to conduct heat. The room-temperature thermal conductivity of carbon materials span an extraordinary large range -- of over five orders of magnitude -- from the lowest in amorphous carbons to the highest in graphene and carbon nanotubes. Here, I review the thermal properties of carbon materials focusing on recent results for graphene, carbon nanotubes and nanostructured carbon materials with different degrees of disorder. Special attention is given to the unusual size dependence of heat conduction in two-dimensional crystals and, specifically, in graphene. I also describe the prospects of applications of graphene and carbon materials for thermal management of electronics.

  16. Rheological Properties of Asphalt Modified by Supramolecular UV Resistant Material-LDHs

    Institute of Scientific and Technical Information of China (English)

    WANG Jinshan; WU Shaopeng; HAN Jun; LIU Xing

    2012-01-01

    Dynamic rheological properties of asphalt modified by Supramolecular UV resistant material-layered double hydroxides(LDHs) was studied by means of the dynamic shear rheometer (DSR) test.Two typical base asphalts were chosen and modified by 2 different LDHs contents.DSR tests were performed on the original samples,samples after exposed to outdoor and samples after the artificial accelerated UV aging tests respectively to analyze the rheological properties.It is found that when the LDHs content is between 3wt% and 5wt% of asphalt weight,the high temperature performance and fatigue resistant property of the modified asphalt become better,the UV aging resistance properties are improved.

  17. Effects of Thermal Treatment on the Dynamic Mechanical Properties of Coal Measures Sandstone

    Science.gov (United States)

    Li, Ming; Mao, Xianbiao; Cao, Lili; Pu, Hai; Mao, Rongrong; Lu, Aihong

    2016-09-01

    Many projects such as the underground gasification of coal seams and coal-bed methane mining (exploitation) widely involve the dynamic problems of coal measures sandstone achieved via thermal treatment. This study examines the dynamic mechanical properties of coal measures sandstone after thermal treatment by means of an MTS653 high-temperature furnace and Split Hopkinson pressure bar test system. Experimental results indicate that 500 °C is a transition point for the dynamic mechanical parameters of coal measures sandstone. The dynamic elastic modulus and peak strength increase linearly from 25 to 500 °C while the dynamic peak strain decreases linearly over the same temperature range. The dynamic elastic modulus and peak strength drop quickly from 500 to 800 °C, with a significant increase in the dynamic peak strain over the same temperature range. The rock mechanics are closely linked to material composition and mesoscopic structure. Analysis by X-ray diffraction and scanning electron microscopy indicate that the molecules inside the sandstone increase in density due to the thermal expansion of the material particles, which effectively improves the deformation resistance and carrying capacity of the sandstone and reduces the likelihood of axial deformation. With heat treatment that exceeds 500 °C, the dynamic mechanical properties rapidly weaken due to the decomposition of kaolinite; additionally, hot cracking of the mineral particles within the materials arises from coal sandstone internal porosity, and other defects gradually appear.

  18. Properties of structural materials in liquid metal environment. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Borgstedt, H.U. [ed.

    1991-12-15

    The International Working Group on Fast Reactors (IWGFR) Specialists Meeting on Properties of Structural Materials in Liquid Metal Environment was held during June 18 to June 20, 1991, at the Nuclear Research Centre (Kernforschungszentrum) in Karlsruhe, Germany. The Specialists Meeting was divided into five technical sessions which addressed topics as follows: Creep-Rupture Behaviour of Structural Materials in Liquid Metal Environment; Behaviour of Materials in Liquid Metal Environments under Off-Normal Conditions;Fatigue and Creep-Fatigue of Structural Materials in Liquid Metal Environment; Crack Propagation in Liquid Sodium; and Conclusions and recommendations. Individual papers have been cataloged separately.

  19. MPOD: A Material Property Open Database linked to structural information

    Science.gov (United States)

    Pepponi, Giancarlo; Gražulis, Saulius; Chateigner, Daniel

    2012-08-01

    Inspired by the Crystallography Open Database (COD), the Material Properties Open Database (MPOD) was given birth. MPOD aims at collecting and making publicly available at no charge tensorial properties (including scalar properties) of phases and linking such properties to structural information of the COD when available. MPOD files are written with the STAR file syntax, used and developed for the Crystallographic Information Files. A dictionary containing new definitions has been written according to the Dictionary Definition Language 1, although some tricks were adopted to allow for multiple entries still avoiding ambiguousness. The initial set includes mechanical properties, elastic stiffness and compliance, internal friction; electrical properties, resistivity, dielectric permittivity and stiffness, thermodynamic properties, heat capacity, thermal conductivity, diffusivity and expansion; electromechanical properties, piezoelectricity, electrostriction, electromechanical coupling; optical properties; piezooptic and photoelastic properties; superconducting properties, critical fields, penetration and coherence lengths. Properties are reported in MPOD files where the original published paper containing the data is cited and structural and experimental information is also given. One MPOD file contains information relative to only one publication and one phase. The files and the information contained therein can also be consulted on-line at http://www.materialproperties.org.

  20. Development and Demonstration of Material Properties Database and Software for the Simulation of Flow Properties in Cementitious Materials

    Energy Technology Data Exchange (ETDEWEB)

    Smith, F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-03-30

    This report describes work performed by the Savannah River National Laboratory (SRNL) in fiscal year 2014 to develop a new Cementitious Barriers Project (CBP) software module designated as FLOExcel. FLOExcel incorporates a uniform database to capture material characterization data and a GoldSim model to define flow properties for both intact and fractured cementitious materials and estimate Darcy velocity based on specified hydraulic head gradient and matric tension. The software module includes hydraulic parameters for intact cementitious and granular materials in the database and a standalone GoldSim framework to manipulate the data. The database will be updated with new data as it comes available. The software module will later be integrated into the next release of the CBP Toolbox, Version 3.0. This report documents the development efforts for this software module. The FY14 activities described in this report focused on the following two items that form the FLOExcel package; 1) Development of a uniform database to capture CBP data for cementitious materials. In particular, the inclusion and use of hydraulic properties of the materials are emphasized; and 2) Development of algorithms and a GoldSim User Interface to calculate hydraulic flow properties of degraded and fractured cementitious materials. Hydraulic properties are required in a simulation of flow through cementitious materials such as Saltstone, waste tank fill grout, and concrete barriers. At SRNL these simulations have been performed using the PORFLOW code as part of Performance Assessments for salt waste disposal and waste tank closure.

  1. Study of normal and shear material properties for viscoelastic model of asphalt mixture by discrete element method

    DEFF Research Database (Denmark)

    Feng, Huan; Pettinari, Matteo; Stang, Henrik

    2015-01-01

    In this paper, the viscoelastic behavior of asphalt mixture was studied by using discrete element method. The dynamic properties of asphalt mixture were captured by implementing Burger’s contact model. Different ways of taking into account of the normal and shear material properties of asphalt mi...

  2. Numerical Derivation of Strain Rate Effects on Material Properties of Masonry with Solid Clay Bricks

    Institute of Scientific and Technical Information of China (English)

    WEI Xueying; HAO Hong

    2006-01-01

    In this paper,numerical method is used to study the strain rate effect on masonry materials.A typical unit of masonry is selected to serve as a representative volume element (RVE).Numerical model of RVE is established with detailed distinctive modeling of brick and mortar with their respective dynamic material properties obtained from laboratory tests.The behavior of brick and mortar are characterized by a dynamic damage model that accounts for rate-sensitive and pressuredependent properties of masonry materials.Dynamic loads of different loading rates are applied to RVE.The equivalent homogenized uniaxial compressive strength,threshold strain and elastic modulus in three directions of the masonry are derived from the simulated responses of the RVE.The strain rate effect on the masonry material with clay brick and mortar,such as the dynamic increase factor (DIF) of the ultimate strength and elastic modulus as a function of strain rate are derived from the numerical results.

  3. Validation of a laboratory method for evaluating dynamic properties of reconstructed equine racetrack surfaces.

    Directory of Open Access Journals (Sweden)

    Jacob J Setterbo

    Full Text Available BACKGROUND: Racetrack surface is a risk factor for racehorse injuries and fatalities. Current research indicates that race surface mechanical properties may be influenced by material composition, moisture content, temperature, and maintenance. Race surface mechanical testing in a controlled laboratory setting would allow for objective evaluation of dynamic properties of surface and factors that affect surface behavior. OBJECTIVE: To develop a method for reconstruction of race surfaces in the laboratory and validate the method by comparison with racetrack measurements of dynamic surface properties. METHODS: Track-testing device (TTD impact tests were conducted to simulate equine hoof impact on dirt and synthetic race surfaces; tests were performed both in situ (racetrack and using laboratory reconstructions of harvested surface materials. Clegg Hammer in situ measurements were used to guide surface reconstruction in the laboratory. Dynamic surface properties were compared between in situ and laboratory settings. Relationships between racetrack TTD and Clegg Hammer measurements were analyzed using stepwise multiple linear regression. RESULTS: Most dynamic surface property setting differences (racetrack-laboratory were small relative to surface material type differences (dirt-synthetic. Clegg Hammer measurements were more strongly correlated with TTD measurements on the synthetic surface than the dirt surface. On the dirt surface, Clegg Hammer decelerations were negatively correlated with TTD forces. CONCLUSIONS: Laboratory reconstruction of racetrack surfaces guided by Clegg Hammer measurements yielded TTD impact measurements similar to in situ values. The negative correlation between TTD and Clegg Hammer measurements confirms the importance of instrument mass when drawing conclusions from testing results. Lighter impact devices may be less appropriate for assessing dynamic surface properties compared to testing equipment designed to simulate hoof

  4. PARAMETRIC ANALYSIS OF THE DYNAMIC PROPERTIES OF ...

    African Journals Online (AJOL)

    static and dynamic analysis of structures [2, 3,4]. ... than by the expected complexity of their behavior. This fact has been .... The computational cost of extracting the vibration modes can be reduced by applying one of the condensation.

  5. Dynamic Oxygen Storage Capacity Measurements on Ceria-Based Material

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Dynamic oxygen storage and release capability (OSC) measurement apparatus was designed to evaluate the OSC performance of ceria-based oxygen storage material. The optimum measurement condition was at a frequency of 0.1 Hz with the inlet gas-flow sequence CO (5S)→O2 (5S)→CO→O2 and a flow rate of 300 ml·min-1. Under this condition, similar regular square wave in the inlet and outlet of the reactor was obtained to guarantee the reliability of the dynamic OSC results. The dynamic OSC performance of the CeO2 and Ce0.67Zr0.33O2 mixed oxide prepared using the citric sol-gel method was studied at the optimum measurement condition with focus on both quantitative and qualitative analyses. The results reveal distinctly that Ce0.67Zr0.33O2 had better dynamic OSC performance because of its higher oxygen migration rate than CeO2. Under dynamic conditions, two CO2 production peaks occurred corresponding to the CO pulse and the O2 pulse, respectively, during the entire cycle. The intensity and ratio between the two CO2 productions were highly influenced by temperature and frequency indicating complex surface phenomena during the oxygen storage/release process. As a result, this set-up can be applied to the evaluation of ceria-based material on the OSC performance.

  6. Field diffusion-like representation and experimental identification of a dynamic magnetization property

    Energy Technology Data Exchange (ETDEWEB)

    Maloberti, Olivier [LEG-INPG/UJF-CNRS UMR 5529: BP 46, 38402 Saint Martin d' Heres cedex (France) and Schneider Electric Corporate Research and Developments, 37 quai Paul Louis Merlin, 38050 Grenoble cedex 9 (France)]. E-mail: olivier.maloberti@schneider-electric.com; Kedous-Lebouc, A. [LEG-INPG/UJF-CNRS UMR 5529: BP 46, 38402 Saint Martin d' Heres cedex (France); Geoffroy, O. [LLN-UJF/INPG-CNRS UPR 5051: 25 avenue des Martyrs, 38050 Grenoble cedex 9 (France); Meunier, G. [LEG-INPG/UJF-CNRS UMR 5529: BP 46, 38402 Saint Martin d' Heres cedex (France); Mazauric, V. [Schneider Electric Corporate Research and Developments, 37 quai Paul Louis Merlin, 38050 Grenoble cedex 9 (France)

    2006-09-15

    So as to fuse dynamic magnetization properties of soft materials with the electromagnetism theory, we investigate the inclusion of microscopic reversal processes related to domains and walls in macroscopic Maxwell equations. We first introduce a model for independent walls and the unidirectional motion mechanism; then we characterize one sample with measurements and analytical calculations in case of one-dimensional linear problems.

  7. Global and local properties used as analyses tools for molecular-dynamics simulations

    Science.gov (United States)

    Bachlechner, Martina E.; Anderson, Jonas T.; Cao, Deng; Leonard, Robert H.; Owens, Eli T.; Schiffbauer, Jarrod E.; Burky, Melissa R.; Ducatman, Samuel C.; Guffey, Eric J.; Serrano Ramos2, Fernando

    2006-03-01

    Molecular dynamics simulations have been used to study mechanical failure in realistic interface materials. Averaging over the individual atoms' contributions yields local and global information including displacements, bond angles, strains, stress tensor components, and pair distribution functions. A combined analysis of global and local properties facilitates detailed insight in the mechanisms of failure, which will eventually guide on how to prevent failure of interfaces.

  8. Dynamic dielectric properties of a wood liquefaction system using polyethylene glycol and glycerol

    Science.gov (United States)

    Mengchao Zhou; Thomas L. Eberhardt; Bo Cai; Chung-Yun Hse; Hui Pan

    2017-01-01

    Microwave-assisted liquefaction has shown potential for rapid thermal processing of lignocellulosic biomass. The efficiency of microwave heating depends largely on the dielectric properties of the materials being heated. The objective of this study was to investigate the dynamic interactions between microwave energy and the reaction system during the liquefaction of a...

  9. PREFACE: International Symposium on Dynamic Deformation and Fracture of Advanced Materials (D2FAM 2013)

    Science.gov (United States)

    Silberschmidt, Vadim V.

    2013-07-01

    Intensification of manufacturing processes and expansion of usability envelopes of modern components and structures in many cases result in dynamic loading regimes that cannot be resented adequately employing quasi-static formulations of respective problems of solid mechanics. Specific features of dynamic deformation, damage and fracture processes are linked to various factors, most important among them being: a transient character of load application; complex scenarios of propagation, attenuation and reflection of stress waves in real materials, components and structures; strain-rate sensitivity of materials properties; various thermo-mechanical regimes. All these factors make both experimental characterisation and theoretical (analytical and numerical) analysis of dynamic deformation and fracture rather challenging; for instance, besides dealing with a spatial realisation of these processes, their evolution with time should be also accounted for. To meet these challenges, an International Symposium on Dynamic Deformation and Fracture of Advanced Materials D2FAM 2013 was held on 9-11 September 2013 in Loughborough, UK. Its aim was to bring together specialists in mechanics of materials, applied mathematics, physics, continuum mechanics, materials science as well as various areas of engineering to discuss advances in experimental and theoretical analysis, and numerical simulations of dynamic mechanical phenomena. Some 50 papers presented at the Symposium by researchers from 12 countries covered various topics including: high-strain-rate loading and deformation; dynamic fracture; impact and blast loading; high-speed penetration; impact fatigue; damping properties of advanced materials; thermomechanics of dynamic loading; stress waves in micro-structured materials; simulation of failure mechanisms and damage accumulation; processes in materials under dynamic loading; a response of components and structures to harsh environment. The materials discussed at D2FAM 2013

  10. Polyvinyl siloxane impression materials: a review of properties and techniques.

    Science.gov (United States)

    Chee, W W; Donovan, T E

    1992-11-01

    Polyvinyl siloxane impression materials have been shown to have excellent properties as impression materials; however, they are sensitive to manipulative variables. Several methods of using very high viscosity (putty) materials to form "trays" to obtain uniform bulk of the wash impression are described, and the disadvantages of each of these techniques is pointed out. It is recommended that for best results acrylic resin custom trays should be used routinely. The interaction of polyvinyl siloxane materials with latex products is also discussed and problems that this inhibition can cause are stated. Suggestions to avoid this interaction are outlined. One of the disadvantages of the impression materials is that it has a relatively short working time. Refrigerating the material will increase working time without affecting accuracy.

  11. Dynamic and kinetic properties of Al-Li melts

    Science.gov (United States)

    Kiselev, A. I.

    2008-12-01

    The dynamic and kinetic properties of Al-Li melts are calculated. The liquid phase of this system is shown to be characterized by three states with different ion distributions and different degrees of electron localization.

  12. Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1992-01-01

    1.1 This guide establishes the essential and desirable elements of data required for the identification in computerized material property databases of fibers, fillers, and core materials used in composite materials. A recommended format for entry of these fields into a computerized database is provided. Examples of the application of this guide are also included. 1.2 The recommended format described in this guide is suggested for use in recording data in a database, which is different from contractural reporting of actual test results. The latter type of information is described in materials specifications shown in business transactions and is subject to agreement between vendor and purchaser. 1.3 The materials covered by this guide include fibers, both continuous and discontinuous, and fillers of various geometries which are used as reinforcements in composite materials, as well as core materials used in sandwich composites. Cores may be foam, honeycomb, or naturally occurring materials such as balsa wood....

  13. Handbook on dielectric and thermal properties of microwaveable materials

    CERN Document Server

    Komarov, Vyacheslav V

    2012-01-01

    The application of microwave energy for thermal processing of different materials and substances is a rapidly growing trend in modern science and engineering. In fact, optimal design work involving microwaves is impossible without solid knowledge of the properties of these materials. Here s a practical reference that collects essential data on the dielectric and thermal properties of microwaveable materials, saving you countless hours on projects in a wide range of areas, including microwave design and heating, applied electrodynamics, food science, and medical technology. This unique book provides hard-to-find information on complex dielectric permittivity of media at industrial, scientific, and medical frequencies (430 MHz, 915MHz, 2.45GHz, 5.8 GHz, and 24.125GHz). Written by a leading expert in the field, this authoritative book does an exceptional job at presenting critical data on various materials and explaining what their key characteristics are concerning microwaves.

  14. Fabrication, properties, and tritium recovery from solid breeder materials

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.E. (Argonne National Lab., IL (USA)); Kondo, T. (Japan Atomic Energy Research Inst., Tokyo (Japan)); Roux, N. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)); Tanaka, S. (Tokyo Univ. (Japan)); Vollath, D. (Kernforschungszentrum Karlsruhe GmbH (Germany, F.R.))

    1991-01-01

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was recognized by the International Thermonuclear Experimental Reactor (ITER) design team in its selection of ceramics as the first option for the ITER breeder material. Blanket design studies have indicated properties in the candidate materials data base that need further investigation. Current studies are focusing on tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between the ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests, some as part of an international collaboration for development of ceramic breeder materials, are underway. 133 refs., 1 fig.

  15. PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

    Directory of Open Access Journals (Sweden)

    Jacek PAWLICKI

    2014-06-01

    Full Text Available Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstructural examinations and identification of the fracture type enabled to describe a correlation between strain rate, strain and microstructure.

  16. Reflector and Shield Material Properties for Project Prometheus

    Energy Technology Data Exchange (ETDEWEB)

    J. Nash

    2005-11-02

    This letter provides updated reflector and shield preliminary material property information to support reactor design efforts. The information provided herein supersedes the applicable portions of Revision 1 to the Space Power Program Preliminary Reactor Design Basis (Reference (a)). This letter partially answers the request in Reference (b) to provide unirradiated and irradiated material properties for beryllium, beryllium oxide, isotopically enriched boron carbide ({sup 11}B{sub 4}C) and lithium hydride. With the exception of {sup 11}B{sub 4}C, the information is provided in Attachments 1 and 2. At the time of issuance of this document, {sup 11}B{sub 4}C had not been studied.

  17. Material Property Characterization of AS4/VRM-34 Textile Laminates

    Science.gov (United States)

    Grenoble, Ray W.; Johnston, William M

    2013-01-01

    Several material properties (modulus, strengths, and fracture toughness) of a textile composite have been evaluated to provide input data to analytical models of Pultruded Rod Stiffened Efficient Unitized Structure (PRSEUS). The material system is based on warp-knitted preforms of AS4 carbon fibers and VRM-34 epoxy resin, which have been processed via resin infusion and oven curing. Tensile, compressive, shear, and fracture toughness properties have been measured at ambient and elevated temperatures. All specimens were tested in as-fabricated (dry) condition. Specimens were tested with and without through-thickness stitching.

  18. Synthesis, Properties and Mineralogy of Important Inorganic Materials

    CERN Document Server

    Warner, Terence E

    2010-01-01

    Intended as a textbook for courses involving preparative solid-state chemistry, this book offers clear and detailed descriptions on how to prepare a selection of inorganic materials that exhibit important optical, magnetic and electrical properties, on a laboratory scale. The text covers a wide range of preparative methods and can be read as separate, independent chapters or as a unified coherent body of work. Discussions of various chemical systems reveal how the properties of a material can often be influenced by modifications to the preparative procedure, and vice versa. References to miner

  19. Direct Imaging of Anisotropic Material Properties using Photorefractive Laser Ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    Telschow, Kenneth Louis; Deason, Vance Albert; Schley, Robert Scott; Watson, Scott Marshall

    1999-07-01

    Anisotropic properties of materials can be determined by measuring the propagation of elastic waves in different directions. A laser imaging approach is presented that utilizes the adaptive property of photorefractive materials to produce a real-time measurement of the antisymmetric Lamb or flexural traveling wave mode displacement and phase. Continuous excitation is employed and the data is recorded and displayed in all directions simultaneously at video camera frame rates. Fourier transform of the data produces an image of the wave slowness in all planar directions. The results demonstrate imaging of microstructural isotropy and anisotropy and stress induced ansiotropy in plates.

  20. Direct Imaging of Anisotropic Material Properties using Photorefractive Laser Ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    K.L. Telschow; R.S. Schley; S.M. Watson; V.A. Deason

    1999-06-01

    Anisotropic properties of materials can be determined by measuring the propagation of elastic waves in different directions. A laser imaging approach is presented that utilizes the adaptive property of photorefractive materials to produce a real-time measurement of the antisymmetric Lamb or flexural traveling wave mode displacement and phase. Continuous excitation is employed and the data is recorded and displayed in all directions simultaneously at video camera frame rates. Fourier transform of the data produces an image of the wave slowness in all planar directions. The results demonstrate imaging of microstructural isotropy and anisotropy and stress induced ansiotropy in plates.

  1. INVESTIGATION OF TRIBOLOGICAL PROPERTIES CuSn10 BEARING MATERIAL

    Directory of Open Access Journals (Sweden)

    Bekir Sadık ÜNLÜ

    2005-01-01

    Full Text Available Bronzes which copper based alloys is widely used because of properties physical, thermal and tribological as journal bearing material. This material that has tribological performance good conclusions gives at journal bearings. In this study, CuSn10 bronze that were manufactured journal bearings friction and wear properties has been examined and compared. SAE 1050 steel shaft has been used as counter abrader. Experiments have been carried out 10 N and 20 N loads, 750 and 1500 rpm, dry and lubricated conditions by using radial journal bearing wear test rig. As a results, high friction coefficient and weigh loss have been obtained at dry condition more than lubricated condition.

  2. Polymers for electricity and electronics materials, properties, and applications

    CERN Document Server

    Drobny, Jiri George

    2011-01-01

    The comprehensive, practical book that explores the principles, properties, and applications of electrical polymers The electrical properties of polymers present almost limitless possibilities for industrial research and development, and this book provides an in-depth look at these remarkable molecules. In addition to traditional applications in insulating materials, wires, and cables, electrical polymers are increasingly being used in a range of emerging technologies. Presenting a comprehensive overview of how electrical polymers function and how they can be applied in the elec

  3. Mechanical properties of some polymer materials used for tooth positioners.

    Science.gov (United States)

    Collett, A R; Cook, W D; West, V C

    1994-10-01

    The chemical composition, thermal behaviour and mechanical properties of three tooth positioner materials, Urethane P1 (P1), White Rubber (WR) and Elastocryl (EL) were investigated. Infra-red spectrophotometry indicated the P1 polyurethane material to be of the polyether type, and EL to be a blend of poly(ethyl methacrylate) and poly(methyl methacrylate) while WR appeared to be filled cis-poly (isoprene) (natural rubber). The glass transition temperature (Tg) for EL was determined as approximately 10 degrees C, and for both P1 and WR the Tg was less than -50 degrees C. The stress relaxation behaviour was assessed in compression by measuring the stress variation with time. The results for all three materials conformed to the superelastic theory of rubber elasticity. EL exhibited both a more rapid rate and higher degree of stress relaxation than did P1 and WR. Recovery from deformation was assessed by compressing cylinders for given periods of time and then measuring the level of reduced residual strain of the material with time. All three materials exhibited significant residual strain (epsilon(t)) over 'clinically relevant' time periods, and the reduced residual strain (epsilon(t)/epsilon(O)) following deformation was greater for EL than P1 or WR. There was some indication that the three materials have some permanent set following deformation. It was concluded that, in considering desirable mechanical properties of tooth positioner materials, EL is the least suitable of the three examined, with none of the materials being ideal.

  4. Characterization of mechanical properties of materials using ultrasound broadband spectroscopy.

    Science.gov (United States)

    Agrawal, Megha; Prasad, Abhinav; Bellare, Jayesh R; Seshia, Ashwin A

    2016-01-01

    This article explores the characterization of homogenous materials (metals, alloys, glass and polymers) by a simple broadband ultrasonic interrogation method. The novelty lies in the use of ultrasound in a continuous way with very low input power (0 dBm or less) and analysis of the transmitted acoustic wave spectrum for material property characterization like speed of sound, density and dimensions of a material. Measurements were conducted on various thicknesses of samples immersed in liquid where continuous-wave, frequency swept ultrasonic energy was incident normal to the sample surface. The electro-acoustic transmission response is analyzed in the frequency domain with respect to a specifically constructed multi-layered analytical model. From the acoustic signature of the sample materials, material properties such as speed of sound and acoustic impedance can be calculated with experimentally derived values found to be in general agreement with the literature and with pulse-echo technique establishing the basis for a non-contact and non-destructive technique for material characterization. Further, by looking at the frequency spacing of the peaks of water when the sample is immersed, the thickness of the sample can be calculated independently from the acoustic response. This technique can prove to be an effective non-contact, non-destructive and fast material characterization technique for a wide variety of materials.

  5. Electron paramagnetic resonance of material properties and processes

    Energy Technology Data Exchange (ETDEWEB)

    Brower, K. L.

    1980-01-01

    This paper demonstrates, primarily for the non-specialist and within the context of new and recent achievements, the diagnostic value of electron paramagnetic resonance (EPR) in the study of material properties and processes. I have selected three EPR studies which demonstrate the elegance and uniqueness of EPR in atomic defect studies and exemplify unusual achievements through the use of new techniques for material measurement and preparation. A brief introduction into the origin, interaction, and detection of unpaired electrons is included.

  6. Thermomechanical Properties of Corundum—Mullite—Zirconia Materials

    Institute of Scientific and Technical Information of China (English)

    ZHONGXiangchong; SUNGengcheng

    1998-01-01

    The mechanical properties at elevated tempera-tures of corundum-mullite materials and the effects of zirconia and titania additions have been investi-gated.The results are correlated with changes in microstructure,Based on the results of these investi-gations ,reaction-sintered corundum-mullite-zirco-nia materials with improved hot strength and ther-mal shock resistance have been developed for refractor-ries usage.

  7. The effects of proton radiation on UHMWPE material properties for space flight and medical applications

    Science.gov (United States)

    Cummings, Chad S.; Lucas, Eric M.; Marro, Justin A.; Kieu, Tri M.; DesJardins, John D.

    2011-11-01

    Ultra High Molecular Weight Polyethylene (UHMWPE) is a polymer widely used as a radiation shielding material in space flight applications and as a bearing material in total joint replacements. As a long chain hydrocarbon based polymer, UHMWPE's material properties are influenced by radiation exposure, and prior studies show that gamma irradiation is effective for both medical sterilization and increased wear resistance in total joint replacement applications. However, the effects of space flight radiation types and doses on UHMWPE material properties are poorly understood. In this study, three clinically relevant grades of UHMWPE (GUR 1020, GUR 1050, and GUR 1020 blended with Vitamin E) were proton irradiated and tested for differences in material properties. Each of the three types of UHMWPE was irradiated at nominal doses of 0 Gy (control), 5 Gy, 10 Gy, 20 Gy, and 35 Gy. Following irradiation, uniaxial tensile testing and thermal testing using Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) were performed. Results show small but significant changes in several material properties between the control (0 Gy) and 35 Gy samples, indicating that proton irradiation could have a effect on the long term performance of UHMWPE in both medical and space flight applications.

  8. Interfacial Properties of an Ionic Liquid by Molecular Dynamics

    NARCIS (Netherlands)

    Heggen, B.; Zhao, W.; Leroy, F.; Dammers, A.T.; Müller-Plathe, F.

    2010-01-01

    We studied the influence of a liquid-vapor interface on dynamic properties like reorientation and diffusion as well as the surface tension of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) by molecular dynamics simulations. In the interfacial region, reorientation of

  9. Interfacial Properties of an Ionic Liquid by Molecular Dynamics

    NARCIS (Netherlands)

    Heggen, B.; Zhao, W.; Leroy, F.; Dammers, A.T.; Müller-Plathe, F.

    2010-01-01

    We studied the influence of a liquid-vapor interface on dynamic properties like reorientation and diffusion as well as the surface tension of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) by molecular dynamics simulations. In the interfacial region, reorientation of

  10. Effect of intercostal muscle and costovertebral joint material properties on human ribcage stiffness and kinematics.

    Science.gov (United States)

    Kindig, Matthew; Li, Zuoping; Kent, Richard; Subit, Damien

    2015-01-01

    Current finite element (FE) models of the human thorax are limited by the lack of local-level validation, especially in the ribcage. This study exercised an existing FE ribcage model for a 50th percentile male under quasi-static point loading and dynamic sternal loading. Both force-displacement and kinematic responses of the ribcage were compared against experimental data. The sensitivity of the model response to changes in the material properties of the costovertebral (CV) joints and intercostal muscles was assessed. The simulations found that adjustments to the CV joints tended to change the amount of rib rotation in the sagittal plane, while changes to the elastic modulus and thickness of the intercostal muscles tended to alter both the stiffness and the direction and magnitude of rib motions. This study can lend insight into the role that the material properties of these two thoracic structures play in the dynamics of the ribcage during a frontal loading condition.

  11. Computation of electronic structure and magnetic properties of strongly correlated materials with LDA+DMFT method

    Science.gov (United States)

    Skornyakov, S. L.; Anisimov, V. I.

    2015-04-01

    In this review, we describe general ideas of the LDA+DMFT method which merges dynamical mean-field theory (DMFT) and density functional theory (in particular the local density approximation (LDA)). Nowadays, the LDA+DMFT computational scheme is the most powerful numerical tool for studying physical properties of real materials and chemical compounds. It incorporates the advantage of DMFT to treat the full range of local dynamical Coulomb correlations and the ability of band methods to describe material-specific band dispersion caused by the lattice periodicity. We briefly discuss underlying physical ideas of LDA+DMFT and its mathematical implementation. Then different algorithms applied to solution of the DMFT impurity problem are briefly described. We then give examples of successful applications of the LDA+DMFT method to study spectral and magnetic properties of recently synthesized compounds like pnictide superconductors as well as classic charge-transfer systems NiO and MnO.

  12. Material deformation dynamics at ultrahigh pressures and strain rates

    Science.gov (United States)

    Remington, B. A.; Park, H. S.; Maddox, B. R.; May, M. J.; Pollaine, S. M.; Prisbrey, S. T.; Rudd, R. E.; Hawreliak, J. A.; Perry, T. S.; Comley, A. J.; Wark, J. S.; Meyers, M. A.

    2010-11-01

    Solid-state dynamics experiments at extreme pressures, up to 10 Mbar, and strain rates (1.e6 -1.e8 1/s) are being developed for the NIF laser. The experimental methods are being developed on the Omega laser facility. VISAR measurements establish the ramped, high-pressure conditions. Recovery experiments offer a look at the residual microstructure. Dynamic diffraction measurements allow phase, shear stress (strength), and possibly twin volume fraction and dislocation density to be inferred. Constitutive models for material strength at these conditions by comparing 2D simulations with experiments measuring the Rayleigh-Taylor instability evolution in solid-state samples of vanadium and tantalum. The material deformation likely falls into the phonon drag regime. We estimate of the (microscopic) phonon drag coefficient, by relating to the (macroscopic) effective lattice viscosity.

  13. The synthesis and properties of nanoscale ionic materials

    KAUST Repository

    Rodriguez, Robert Salgado

    2010-02-17

    In this article we discuss the effect of constituents on structure, flow, and thermal properties of nanoscale ionic materials (NIMs). NIMs are a new class of nanohybrids consisting of a nanometer-sized core, a charged corona covalently attached to the core, and an oppositely charged canopy. The hybrid nature of NIMs allows for their properties to be engineered by selectively varying their components. The unique properties associated with these systems can help overcome some of the issues facing the implementation of nanohybrids to various commercial applications, including carbon dioxide capture,water desalinization and as lubricants. Copyright © 2010 John Wiley & Sons, Ltd.

  14. Dynamic Properties of Offshore Wind Turbine Foundations

    DEFF Research Database (Denmark)

    Damgaard, Mads

    with static springs along the foundation and soil damping applied as modal damping. The methods, however, do not account for the dynamic stiffness due to inertia forces, and a welldefined representation of the dissipation effects in the soil is neglected. This in turn forms the basis of the current thesis...... that capture the most important effects of the dynamic wind turbine response. To overcome this, sequential or fully coupled aero-hydro-elastic simulations are often conducted where the soil–structure interaction is incorporated via the principle of an equivalent fixity depth or by a so-called Winkler approach...

  15. Evaluation of Water Resistance and Diffusion Properties of Paint Materials

    Directory of Open Access Journals (Sweden)

    J. Drchalová

    2001-01-01

    Full Text Available A simple method is presented for evaluating the water-proofness quality of paints on lining materials. The method is based on measuring the integral capillarity in dependence on time, and then comparing this value to the value determined for the basic lining material. Measurements of the effective water vapor permeability then provide information on the risk of condensation which may increase after applying the paint. A practical application of the method is performed with four Karlocolor paints on glass concrete substrates. All the Karlocolor paints are found to be very effective materials for driven rain protection. The diffusion properties of all the paints are found to be excellent.

  16. A mixed method for measuring low-frequency acoustic properties of macromolecular materials

    Institute of Scientific and Technical Information of China (English)

    LIU; Hongwei; YAO; Lei; ZHAO; Hong; ZHANG; Jichuan; XUE; Zhaohong

    2006-01-01

    A mixed method for measuring low-frequency acoustic properties of macromolecular materials is presented.The dynamic mechanical parameters of materials are first measured by using Dynamic Mechanical Thermal Apparatus(DMTA) at low frequencies,usually less than 100 Hz; then based on the Principles of Time-Temperature Super position (TTS),these parameters are extended to the frequency range that acousticians are concerned about,usually from hundreds to thousands of hertz; finally the extended dynamic mechanical parameters are transformed into acoustic parameters with the help of acoustic measurement and inverse analysis.To test the feasibility and accuracy,we measure a kind of rubber sample in DMTA and acquire the basic acoustic parameters of the sample by using this method.While applying the basic parameters to calculating characteristics of the sample in acoustic pipe,a reasonable agreement of sound absorption coefficients is obtained between the calculations and measurements in the acoustic pipe.

  17. Instability in magnetic materials with a dynamical axion field.

    Science.gov (United States)

    Ooguri, Hirosi; Oshikawa, Masaki

    2012-04-20

    It has been pointed out that axion electrodynamics exhibits instability in the presence of a background electric field. We show that the instability leads to a complete screening of an applied electric field above a certain critical value and the excess energy is converted into a magnetic field. We clarify the physical origin of the screening effect and discuss its possible experimental realization in magnetic materials where magnetic fluctuations play the role of the dynamical axion field.

  18. Determination of replicate composite bone material properties using modal analysis.

    Science.gov (United States)

    Leuridan, Steven; Goossens, Quentin; Pastrav, Leonard; Roosen, Jorg; Mulier, Michiel; Denis, Kathleen; Desmet, Wim; Sloten, Jos Vander

    2017-02-01

    Replicate composite bones are used extensively for in vitro testing of new orthopedic devices. Contrary to tests with cadaveric bone material, which inherently exhibits large variability, they offer a standardized alternative with limited variability. Accurate knowledge of the composite's material properties is important when interpreting in vitro test results and when using them in FE models of biomechanical constructs. The cortical bone analogue material properties of three different fourth-generation composite bone models were determined by updating FE bone models using experimental and numerical modal analyses results. The influence of the cortical bone analogue material model (isotropic or transversely isotropic) and the inter- and intra-specimen variability were assessed. Isotropic cortical bone analogue material models failed to represent the experimental behavior in a satisfactory way even after updating the elastic material constants. When transversely isotropic material models were used, the updating procedure resulted in a reduction of the longitudinal Young's modulus from 16.00GPa before updating to an average of 13.96 GPa after updating. The shear modulus was increased from 3.30GPa to an average value of 3.92GPa. The transverse Young's modulus was lowered from an initial value of 10.00GPa to 9.89GPa. Low inter- and intra-specimen variability was found. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Research of properties of modern heat-insulation materials

    Directory of Open Access Journals (Sweden)

    A. S. Shcherbak

    2013-04-01

    Full Text Available Purpose. To study the modern heat-insulating materials presented at the market of Ukraine and to estimate the efficiency of their application. Methodology. Research and analysis of heat-insulating materials presented at the market of Ukraine, according to the existing standards. Findings. To ensure the energy efficiency in buildings and constructions it is necessary to apply the domestic heat-insulating material, which possesses the given thermo technical characteristics, reduced indexes of water absorption, flammability and toxicity, as well as durability and relatively low self–cost. Originality. Basic heat-insulating materials, which are most widely used in construction are systematized, the researches of their properties are conducted and the foam glass is chosen as the most effective heat-insulating material. It is characterized by high thermo technical characteristics and possesses the best ecological indexes, as well as the sturdiness for aggressive factors influence. Practical value. Special attention deserves the insulating material foam glass, which is a synthetic silicate material with evenly placed pores (0.1 ... 5.0 mm separated by thin septa with a vitreous substance possesses the necessary properties and by aforesaid may be accepted for studies aimed its improvement (modification. The results of researches can be applied in the foam glass production, which is used for heat-insulation of buildings and constructions, equipment, pipelines etc.

  20. Sub-nanosecond optical diagnostics of laser-material interaction and dynamic microstructure of materials

    Energy Technology Data Exchange (ETDEWEB)

    Paisley, D.L.; Stahl, D.B.

    1993-03-01

    Several optical diagnostic techniques are used to evaluate the dynamic response of materials to intense dynamic loading and unloading, high stress and strain, and pressure. Velocity interferometry and electronic streak photography, each with sub-nanosecond time resolution, are used to record dynamic material response. Laser-launched flat plates are accelerated to 10{sup 12} m/s{sup 2} with terminal velocities >5 km/s. By impacting these plates into target samples, high strain rates (10{sup 8} sec{sup {minus}1}) and pressures >100 GPa have been generated for a duration of 0.8--5 nanoseconds. The efficacy and limitations of each technique are detailed and applications to other fields discussed.

  1. Sub-nanosecond optical diagnostics of laser-material interaction and dynamic microstructure of materials

    Energy Technology Data Exchange (ETDEWEB)

    Paisley, D.L.; Stahl, D.B.

    1993-01-01

    Several optical diagnostic techniques are used to evaluate the dynamic response of materials to intense dynamic loading and unloading, high stress and strain, and pressure. Velocity interferometry and electronic streak photography, each with sub-nanosecond time resolution, are used to record dynamic material response. Laser-launched flat plates are accelerated to 10[sup 12] m/s[sup 2] with terminal velocities >5 km/s. By impacting these plates into target samples, high strain rates (10[sup 8] sec[sup [minus]1]) and pressures >100 GPa have been generated for a duration of 0.8--5 nanoseconds. The efficacy and limitations of each technique are detailed and applications to other fields discussed.

  2. Mechanics of advanced materials analysis of properties and performance

    CERN Document Server

    Matveenko, Valery

    2015-01-01

    The last decades have seen a large extension of types of materials employed in various applications. In many cases these materials demonstrate mechanical properties and performance that vary significantly from those of their traditional counterparts. Such uniqueness is sought – or even specially manufactured – to meet increased requirements on modern components and structures related to their specific use. As a result, mechanical behaviors of these materials under different loading and environmental conditions are outside the boundaries of traditional mechanics of materials, presupposing development of new characterization techniques, theoretical descriptions and numerical tools. The book presents interesting examples of recent developments in this area. Among the studied materials are bulk metallic glasses, metamaterials, special composites, piezoelectric smart structures, nonwovens, etc.

  3. Comparison of shrinkage related properties of various patch repair materials

    Science.gov (United States)

    Kristiawan, S. A.; Fitrianto, R. S.

    2017-02-01

    A patch repair material has been developed in the form of unsaturated polyester resin (UPR)-mortar. The performance and durability of this material are governed by its compatibility with the concrete being repaired. One of the compatibility issue that should be tackled is the dimensional compatibility as a result of differential shrinkage between the repair material and the concrete substrate. This research aims to evaluate such shrinkage related properties of UPR-mortar and to compare with those of other patch repair materials. The investigation includes the following aspects: free shrinkage, resistance to delamination and cracking. The results indicate that UPR-mortar poses a lower free shrinkage, lower risk of both delamination and cracking tendency in comparison to other repair materials.

  4. Surface effects on the mechanical properties of nanoporous materials

    Energy Technology Data Exchange (ETDEWEB)

    Xia Re [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Li Xide; Feng Xiqiao [AML, Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Qin Qinghua [School of Engineering, Australian National University, Canberra, ACT 0200 (Australia); Liu Jianlin, E-mail: fengxq@tsinghua.edu.cn [Department of Engineering Mechanics, China University of Petroleum, Qingdao 266555 (China)

    2011-07-01

    Using the theory of surface elasticity, we investigate the mechanical properties of nanoporous materials. The classical theory of porous materials is modified to account for surface effects, which become increasingly important as the characteristic sizes of microstructures shrink to nanometers. First, a refined Timoshenko beam model is presented to predict the effective elastic modulus of nanoporous materials. Then the surface effects on the elastic microstructural buckling behavior of nanoporous materials are examined. In particular, nanoporous gold is taken as an example to illustrate the application of the proposed model. The results reveal that both the elastic modulus and the critical buckling behavior of nanoporous materials exhibit a distinct dependence on the characteristic sizes of microstructures, e.g. the average ligament width.

  5. SOME DYNAMICAL PROPERTIES OF QUADRATIC RATIONAL MAPS

    Institute of Scientific and Technical Information of China (English)

    YINYONGCHENG

    1994-01-01

    This paper studies the dynamics of the analytic family z+1/z+b and describes the topology of the parameter space, structural stability and J-stability. The mapping class group of almost all maps of the above family is determined.

  6. Influence of materials' optical response on actuation dynamics by Casimir forces

    Science.gov (United States)

    Sedighi, M.; Broer, W. H.; Van der Veeke, S.; Svetovoy, V. B.; Palasantzas, G.

    2015-06-01

    The dependence of the Casimir force on the frequency-dependent dielectric functions of interacting materials makes it possible to tailor the actuation dynamics of microactuators. The Casimir force is largest for metallic interacting systems due to the high absorption of conduction electrons in the far-infrared range. For less conductive systems, such as phase change materials or conductive silicon carbide, the reduced force offers the advantage of increased stable operation of MEMS devices against pull-in instabilities that lead to unwanted stiction. Bifurcation analysis with phase portraits has been used to compare the sensitivity of a model actuator when the optical properties are altered.

  7. Bone strength and material properties of the glenoid

    DEFF Research Database (Denmark)

    Frich, Lars Henrik; Jensen, N.C.; Odgaard, A.;

    1997-01-01

    The quality of the glenoid bone is important to a successful total shoulder replacement. Finite element models have been used to model the response of the glenoid bone to an implanted prosthesis. Because very little is known about the bone strength and the material properties at the glenoid, thes...

  8. Food material properties and early hominin processing techniques.

    Science.gov (United States)

    Zink, Katherine D; Lieberman, Daniel E; Lucas, Peter W

    2014-12-01

    Although early Homo is hypothesized to have used tools more than australopiths to process foods prior to consumption, it is unknown how much the food processing techniques they used altered the material properties of foods, and therefore the masticatory forces they generated, and how well they were able to comminute foods. This study presents experimental data on changes to food material properties caused by mechanical tenderization (pounding with a stone tool) and cooking (dry roasting) of two foods likely to have been important components of the hominin diet: meat and tubers. Mechanical tenderization significantly decreased tuber toughness by 42%, but had no effect on meat toughness. Roasting significantly decreased several material properties of tubers correlated with masticatory effort including toughness (49%), fracture stress (28%) and elastic modulus (45%), but increased the toughness (77%), fracture stress (50%-222%), and elastic modulus of muscle fibers in meat (308%). Despite increasing many material properties of meat associated with higher masticatory forces, roasting also decreased measured energy loss by 28%, which likely makes it easier to chew. These results suggest that the use of food processing techniques by early Homo probably differed for meat and tubers, but together would have reduced masticatory effort, helping to relax selection to maintain large, robust faces and large, thickly enameled teeth.

  9. Tailoring material properties of a nanofibrous extracellular matrix derived hydrogel

    Science.gov (United States)

    Johnson, Todd D.; Lin, Stephen Y.; Christman, Karen L.

    2011-12-01

    In the native tissue, the interaction between cells and the extracellular matrix (ECM) is essential for cell migration, proliferation, differentiation, mechanical stability, and signaling. It has been shown that decellularized ECMs can be processed into injectable formulations, thereby allowing for minimally invasive delivery. Upon injection and increase in temperature, these materials self-assemble into porous gels forming a complex network of fibers with nanoscale structure. In this study we aimed to examine and tailor the material properties of a self-assembling ECM hydrogel derived from porcine myocardial tissue, which was developed as a tissue specific injectable scaffold for cardiac tissue engineering. The impact of gelation parameters on ECM hydrogels has not previously been explored. We examined how modulating pH, temperature, ionic strength, and concentration affected the nanoscale architecture, mechanical properties, and gelation kinetics. These material characteristics were assessed using scanning electron microscopy, rheometry, and spectrophotometry, respectively. Since the main component of the myocardial matrix is collagen, many similarities between the ECM hydrogel and collagen gels were observed in terms of the nanofibrous structure and modulation of properties by altering ionic strength. However, variation from collagen gels was noted for the gelation temperature along with varied times and rates of gelation. These discrepancies when compared to collagen are likely due to the presence of other ECM components in the decellularized ECM based hydrogel. These results demonstrate how the material properties of ECM hydrogels could be tailored for future in vitro and in vivo applications.

  10. Thermal properties of hemp fibre non-woven materials

    Science.gov (United States)

    Freivalde, Liga; Kukle, Silvija; Russell, Stephen

    2013-12-01

    This review considers the thermal properties analysis of hemp fiber non-woven materials made by three different manufacturing technologies - thermal bonding, needle-punching and hydro-entanglement. For non-wovens development two hemp fibers cultivars grown in Latvia were used - Purini and Bialobrzeskie. Thermal resistance, conductivity and the effects of several parameters on thermal performance are revised.

  11. Investigation of Effective Material Properties of Stony Meteorites

    Science.gov (United States)

    Agrawal, Parul; Carlozzi, Alex; Bryson, Kathryn

    2016-01-01

    To assess the threat posed by an asteroid entering Earth's atmosphere, one must predict if, when, and how it fragments during entry. A comprehensive understanding of the Asteroid material properties is needed to achieve this objective. At present, the meteorite material found on Earth are the only objects from an entering asteroid that can be used as representative material and be tested inside a laboratory setting. Therefore, unit cell models are developed to determine the effective material properties of stony meteorites and in turn deduce the properties of asteroids. The unit cell is representative volume that accounts for diverse minerals, porosity, and matrix composition inside a meteorite. The various classes under investigation includes H-class, L-class, and LL-class chondrites. The effective mechanical properties such as Young's Modulus and Poisson's Ratio of the unit cell are calculated by performing several hundreds of Monte-Carlo simulations. Terrestrial analogs such as Basalt and Gabbro are being used to validate the unit cell methodology.

  12. I. The metabolic properties of plutonium and allied materials

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, J.G.

    1948-05-24

    This report on the metabolic properties of plutonium and related radioactive materials presents experimental information in the following areas: radioautographic studies; tracer studies (with tables of accumulation in tissues) of actinium, radio-zirconium, technetium, radio-rubidium, radio-germanium, beryllium, and cadmium; decontamination and bone metabolism studies; and radio-chemical isolation.

  13. Material and Flexural Properties of Fiber-reinforced Rubber Concrete

    Science.gov (United States)

    Helminger, Nicholas P.

    The purpose of this research is to determine the material properties of rubber concrete with the addition of fibers, and to determine optimal mixture dosages of rubber and fiber in concrete for structural applications. Fiber-reinforced concrete and rubberized concrete have been researched separately extensively, but this research intends to combine both rubber and fiber in a concrete matrix in order to create a composite material, fiber-reinforced rubber concrete (FRRC). Sustainability has long been important in engineering design, but much of the previous research performed on sustainable concrete does not result in a material that can be used for practical purposes. While still achieving a material that can be used for structural applications, economical considerations were given when choosing the proportions and types of constituents in the concrete mix. Concrete mixtures were designed, placed, and tested in accordance with common procedures and standards, with an emphasis on practicality. Properties that were investigated include compressive strength, tensile strength, modulus of elasticity, toughness, and ductility. The basis for determining the optimal concrete mixture is one that is economical, practical, and exhibits ductile properties with a significant strength. Results show that increasing percentages of rubber tend to decrease workability, unit weight, compressive strength, split tensile strength, and modulus of elasticity while the toughness is increased. The addition of steel needle fibers to rubber concrete increases unit weight, compressive strength, split tensile strength, modulus of elasticity, toughness, and ductility of the composite material.

  14. Experimental analysis of electrical properties of composite materials

    Science.gov (United States)

    Fiala, L.; Rovnaník, P.; Černý, R.

    2017-02-01

    Dry cement-based composites are electrically non-conductive materials that behave in electric field like dielectrics. However, a relatively low amount of electrically conductive admixture significantly increases the electrical conductivity which extends applicability of such materials in practice. Therefore, they can be used as self-monitoring sensors controlling development of cracks; as sensors monitoring moisture content or when treated by an external electrical voltage as heat sources used for deicing of material's surface layer. Alkali-activated aluminosilicates (AAA), as competing materials to cement-based materials, are intensively investigated in the present due to their superior durability and environmental impact. Whereas the electrical properties of AAA are similar to those cement-based, they can be enhanced in the same way. In both cases, it is crucial to find a reasonable amount of electrically conductive phase to design composites with a sufficient electrical conductivity at an affordable price. In this paper, electrical properties of composites based on AAA binder and electrically conductive admixture represented by carbon nanotubes (CNT) are investigated. Measurements of electrical properties are carried out by means of 2-probes DC technique on nine types of samples; reference sample without the conductive phase and samples with CNT admixture in amount of 0.1 % - 2.5 % by vol. A significant increase of the electrical conductivity starts from the amount of 0.5 % CNT admixture and in case of 2.5 % CNT is about three orders of magnitude higher compared to the reference sample.

  15. Impact and dynamic mechanical thermal properties of textile silk reinforced epoxy resin composites

    Science.gov (United States)

    Yang, K.; Guan, J.

    2016-07-01

    Silk fabric reinforced epoxy resin composites (SFRPs) were prepared using simple techniques of hand lay-up, hot-press and vacuum treatment, and a series of volume fractions of silk reinforcements were achieved. The impact properties and dynamic mechanical properties of SFRPs were investigated using a pendulum impact testing method and dynamic mechanical thermal analysis (DMTA). The results suggest that silk reinforcement could greatly enhance the mechanical performances of SFRPs. The impact strength reached a maximum of 71 kJ/m2 for 60%-silk SFRP, which demonstrated a potential of silk composites for defence and impact- resistant materials.

  16. Development and Analysis of Synthetic Composite Materials Emulating Patient AAA Wall Material Properties

    Science.gov (United States)

    Margossian, Christa M.

    Abdominal Aortic Aneurysm (AAA) rupture accounts for 14,000 deaths a year in the United States. Since the number of ruptures has not decreased significantly in recent years despite improvements in imaging and surgical procedures, there is a need for an accurate, noninvasive technique capable of establishing rupture risk for specific patients and discriminating lesions at high risk. In this project, synthetic composite materials replicating patient-specific wall stiffness and strength were developed and their material properties evaluated. Composites utilizing various fibers were developed to give a range of stiffness from 1825.75 kPa up through 8187.64 kPa with one base material, Sylgard 170. A range of strength from 631.12 kPa to 1083 kPa with the same base material was also found. By evaluating various base materials and various reinforcing fibers, a catalogue of stiffnesses and strengths was started to allow for adaptation to specific patient properties. Three specific patient properties were well-matched with two composites fabricated: silk thread-reinforced Sylgard 170 and silk thread-reinforced Dragon Skin 20. The composites showed similar stiffnesses to the specific patients while reaching target stresses at particular strains. Not all patients were matched with composites as of yet, but recommendations for future matches are able to be determined. These composites will allow for the future evaluation of flow-induced wall stresses in models replicating patient material properties and geometries.

  17. Preparation and Properties of Carbon Fiber Chiral Materials

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ping; HUANG Zhixin; WANG Guoqing

    2008-01-01

    The chiral materials were prepared by using the carbon fiber helices as chiral inclusions,and the composite of Fe3O4 and polyaniline as matrix.The electromagnetic properties,including the rotation angles,the axial ratios and the complex chirality parameters,were measured by using a circular waveguide method in the 8.5-11.0 GHz frequency range.The dependence of these electromagnetic properties on the frequency and the concentration of the Fe3O4 in the composite matrix were analyzed.The results show that an appropriate concentration of Fe3O4 in the matrix is useful in improving the electromagnetic properties of the chiral material.

  18. The Electrical and Dynamical Properties of Biomembranes

    DEFF Research Database (Denmark)

    Mosgaard, Lars Dalskov

    into account the coupling between thermodynamical uctuations and the available heat reservoir. The next step is to combine the knowledge on lipid membranes subjected to an electrical eld with the knowledge on their relaxation behavior and use our understanding to attempt to re-evaluate the results of common......-dimensional layers are literally vital for the cell, as membranes work as catalysts for some of the main chemical reactions involved in cell survival and homeostasis and govern all communication between a cell and its surroundings. The focus of the work presented in this thesis is to understand how...... the physical properties of lipid membranes relate to the behavior and functional properties of biological membranes, with special attention to the role of biological membranes in nerve signal propagation. We start by exploring the properties of polar lipid membranes in order to tackle the problem...

  19. Identification of material properties of sandwich structure with piezoelectric patches

    Directory of Open Access Journals (Sweden)

    Zemčík R.

    2008-11-01

    Full Text Available The work focuses on light-weight sandwich structures made of carbon-epoxy skins and foam core which have unique bending stiffness compared to conventional materials. The skins are manufactured by vacuum autoclave technology from unidirectional prepregs and the sandwich is then glued together. The resulting material properties of the structure usually differ from those provided by manufacturer or even those obtained from experimental tests on separate materials, which makes computational models unreliable. Therefore, the properties are identified using the combination of experimental analysis of the sandwich with attached piezoelectric transducer and corresponding static and modal finite element analyses. Simple mathematical optimization with repetitive finite element solution is used. The model is then verified by transient analysis when the piezoelectric patch is excited by harmonic signals covering the first two eigen-frequencies and the induced oscillations are measured by laser sensor.

  20. Effects of Material Properties on Bacterial Adhesion and Biofilm Formation.

    Science.gov (United States)

    Song, F; Koo, H; Ren, D

    2015-08-01

    Adhesion of microbes, such as bacteria and fungi, to surfaces and the subsequent formation of biofilms cause multidrug-tolerant infections in humans and fouling of medical devices. To address these challenges, it is important to understand how material properties affect microbe-surface interactions and engineer better nonfouling materials. Here we review the recent progresses in this field and discuss the main challenges and opportunities. In particular, we focus on bacterial biofilms and review the effects of surface energy, charge, topography, and stiffness of substratum material on bacterial adhesion. We summarize how these surface properties influence oral biofilm formation, and we discuss the important findings from nondental systems that have potential applications in dental medicine. © International & American Associations for Dental Research 2015.

  1. Structure-property relationships in silica-siloxane nanocomposite materials

    Energy Technology Data Exchange (ETDEWEB)

    Ulibarri, T.A.; Derzon, D.K.; Wang, L.C.

    1997-03-01

    The simultaneous formation of a filler phase and a polymer matrix via in situ sol-gel techniques provides silica-siloxane nanocomposite materials of high strength. This study concentrates on the effects of temperature and relative humidity on a trimodal polymer system in an attempt to accelerate the reaction as well as evaluate subtle process- structure-property relations. It was found that successful process acceleration is only viable for high humidity systems when using the tin(IV) catalyst dibutyltin dilaurate. Processes involving low humidity were found to be very temperature and time dependent. Bimodal systems were investigated and demonstrated that the presence of a short-chain component led to enhanced material strength. This part of the study also revealed a link between the particle size and population density and the optimization of material properties.

  2. Dynamic material strength measurement utilizing magnetically applied pressure-shear

    Directory of Open Access Journals (Sweden)

    Alexander C.S.

    2012-08-01

    Full Text Available Magnetically applied pressure-shear (MAPS is a recently developed technique used to measure dynamic material strength developed at Sandia National Laboratories utilizing magneto-hydrodynamic (MHD drive pulsed power systems. MHD drive platforms generate high pressures by passing a large current through a pair of parallel plate conductors which, in essence, form a single turn magnet coil. Lorentz forces resulting from the interaction of the self-generated magnetic field and the drive current repel the plates and result in a high pressure ramp wave propagating in the conductors. This is the principle by which the Sandia Z Machine operates for dynamic material testing. MAPS relies on the addition of a second, external magnetic field applied orthogonally to both the drive current and the self-generated magnetic field. The interaction of the drive current and this external field results in a shear wave being induced directly in the conductors. Thus both longitudinal and shear stresses are generated. These stresses are coupled to a sample material of interest where shear strength is probed by determining the maximum transmissible shear stress in the state defined by the longitudinal compression. Both longitudinal and transverse velocities are measured via a specialized velocity interferometer system for any reflector (VISAR. Pressure and shear strength of the sample are calculated directly from the VISAR data. Results of tests on several materials at modest pressures (∼10GPa will be presented and discussed.

  3. Millimeter wave and terahertz dielectric properties of biological materials

    Science.gov (United States)

    Khan, Usman Ansar

    Broadband dielectric properties of materials can be employed to identify, detect, and characterize materials through their unique spectral signatures. In this study, millimeter wave, submillimeter wave, and terahertz dielectric properties of biological substances inclusive of liquids, solids, and powders were obtained using Dispersive Fourier Transform Spectroscopy (DFTS). Two broadband polarizing interferometers were constructed to test materials from 60 GHz to 1.2 THz. This is an extremely difficult portion of the frequency spectrum to obtain a material's dielectric properties since neither optical nor microwave-based techniques provide accurate data. The dielectric characteristics of liquids such as cyclohexane, chlorobenzene, benzene, ethanol, methanol, 1,4 dioxane, and 10% formalin were obtained using the liquid interferometer. Subsequently the solid interferometer was utilized to determine the dielectric properties of human breast tissues, which are fixed and preserved in 10% formalin. This joint collaboration with the Tufts New England Medical Center demonstrated a significant difference between the dielectric response of tumorous and non-tumorous breast tissues across the spectrum. Powders such as anthrax, flour, talc, corn starch, dry milk, and baking soda have been involved in a number of security threats and false alarms around the globe in the last decade. To be able to differentiate hoax attacks and serious security threats, the dielectric properties of common household powders were also examined using the solid interferometer to identify the powders' unique resonance peaks. A new sample preparation kit was designed to test the powder specimens. It was anticipated that millimeter wave and terahertz dielectric characterization will enable one to clearly distinguish one powder from the other; however most of the powders had relatively close dielectric responses and only Talc had a resonance signature recorded at 1.135 THz. Furthermore, due to

  4. Material Properties Analysis of Structural Members in Pumpkin Balloons

    Science.gov (United States)

    Sterling, W. J.

    2003-01-01

    The efficient design, service-life qualification, and reliability predictions for lightweight aerospace structures require careful mechanical properties analysis of candidate structural materials. The demand for high-quality laboratory data is particularly acute when the candidate material or the structural design has little history. The pumpkin-shaped super-pressure balloon presents both challenges. Its design utilizes load members (tendons) extending from apex to base around the gas envelope to achieve a lightweight structure. The candidate tendon material is highly weight-efficient braided HM cord. Previous mechanical properties studies of Zylon have focused on fiber and yarn, and industrial use of the material in tensile applications is limited. For high-performance polymers, a carefully plamed and executed properties analysis scheme is required to ensure the data are relevant to the desired application. Because no directly-applicable testing standard was available, a protocol was developed based on guidelines fiom professional and industry organizations. Due to the liquid-crystalline nature of the polymer, the cord is very stiff, creeps very little, and does not yield. Therefore, the key material property for this application is the breaking strength. The pretension load and gauge length were found to have negligible effect on the measured breaking strength over the ranges investigated. Strain rate was found to have no effect on breaking strength, within the range of rates suggested by the standards organizations. However, at the lower rate more similar to ULDB operations, the strength was reduced. The breaking strength increased when the experiment temperature was decreased from ambient to 183K which is the lowest temperature ULDB is expected to experience. The measured strength under all test conditions was well below that resulting from direct scale-up of fiber strength based on the manufacturers data. This expected result is due to the effects of the

  5. Properties of granular analogue model materials: A community wide survey

    Science.gov (United States)

    Klinkmüller, M.; Schreurs, G.; Rosenau, M.; Kemnitz, H.

    2016-08-01

    We report the material properties of 26 granular analogue materials used in 14 analogue modelling laboratories. We determined physical characteristics such as bulk density, grain size distribution, and grain shape, and performed ring shear tests to determine friction angles and cohesion, and uniaxial compression tests to evaluate the compaction behaviour. Mean grain size of the materials varied between c. 100 and 400 μm. Analysis of grain shape factors shows that the four different classes of granular materials (14 quartz sands, 5 dyed quartz sands, 4 heavy mineral sands and 3 size fractions of glass beads) can be broadly divided into two groups consisting of 12 angular and 14 rounded materials. Grain shape has an influence on friction angles, with most angular materials having higher internal friction angles (between c. 35° and 40°) than rounded materials, whereas well-rounded glass beads have the lowest internal friction angles (between c. 25° and 30°). We interpret this as an effect of intergranular sliding versus rolling. Most angular materials have also higher basal friction angles (tested for a specific foil) than more rounded materials, suggesting that angular grains scratch and wear the foil. Most materials have an internal cohesion in the order of 20-100 Pa except for well-rounded glass beads, which show a trend towards a quasi-cohesionless (C < 20 Pa) Coulomb-type material. The uniaxial confined compression tests reveal that rounded grains generally show less compaction than angular grains. We interpret this to be related to the initial packing density after sifting, which is higher for rounded grains than for angular grains. Ring-shear test data show that angular grains undergo a longer strain-hardening phase than more rounded materials. This might explain why analogue models consisting of angular grains accommodate deformation in a more distributed manner prior to strain localisation than models consisting of rounded grains.

  6. Polyunsaturation in lipid membranes: dynamic properties and lateral pressure profiles.

    Science.gov (United States)

    Ollila, Samuli; Hyvönen, Marja T; Vattulainen, Ilpo

    2007-03-29

    We elucidate the influence of unsaturation on single-component membrane properties, focusing on their dynamical aspects and lateral pressure profiles across the membrane. To this end, we employ atomistic molecular dynamics simulations to study five different membrane systems with varying degrees of unsaturation, starting from saturated membranes and systematically increasing the level of unsaturation, ending up with a bilayer of phospholipids containing the docosahexaenoic acid. For an increasing level of unsaturation, we find considerable effects on dynamical properties, such as accelerated dynamics of the phosphocholine head groups and glycerol backbones and speeded up rotational dynamics of the lipid molecules. The lateral pressure profile is found to be altered by the degree of unsaturation. For an increasing number of double bonds, the peak in the middle of the bilayer decreases. This is compensated for by changes in the membrane-water interface region in terms of increasing peak heights of the lateral pressure profile. Implications of the findings are briefly discussed.

  7. Dynamic properties of network motifs contribute to biological network organization.

    Directory of Open Access Journals (Sweden)

    Robert J Prill

    2005-11-01

    Full Text Available Biological networks, such as those describing gene regulation, signal transduction, and neural synapses, are representations of large-scale dynamic systems. Discovery of organizing principles of biological networks can be enhanced by embracing the notion that there is a deep interplay between network structure and system dynamics. Recently, many structural characteristics of these non-random networks have been identified, but dynamical implications of the features have not been explored comprehensively. We demonstrate by exhaustive computational analysis that a dynamical property--stability or robustness to small perturbations--is highly correlated with the relative abundance of small subnetworks (network motifs in several previously determined biological networks. We propose that robust dynamical stability is an influential property that can determine the non-random structure of biological networks.

  8. Dynamical properties of the Lorentz gas

    Science.gov (United States)

    Sharma, K. C.; Ranganathan, S.; Egelstaff, P. A.; Soper, A. K.

    1987-07-01

    A Lorentz gas interacting with a Lennard-Jones (LJ) potential and obeying classical equations of motion has been simulated by the molecular-dynamics method. A system of 255 Ar particles and one H2 molecule at a reduced Ar density 0.413 and temperature 2.475 is simplified by allowing the ``argon'' to have infinite mass, and the hydrogen molecule interacts with Ar atoms via the LJ potential. The simulated incoherent dynamic structure factor Ss(Q,ω) for the hydrogen molecule, which is corrected for the rotational states, is found to be in reasonable agreement with the experimental data of Egelstaff et al. (unpublished). One-parameter phenomenological model calculations are also compared to these data.

  9. How to determine composite material properties using numerical homogenization

    DEFF Research Database (Denmark)

    Andreassen, Erik; Andreasen, Casper Schousboe

    2014-01-01

    Numerical homogenization is an efficient way to determine effective macroscopic properties, such as the elasticity tensor, of a periodic composite material. In this paper an educational description of the method is provided based on a short, self-contained Matlab implementation. It is shown how t...... cell of the periodic material can take the shape of a square, rectangle, or parallelogram, allowing for all kinds of 2D periodicities. © 2013 Elsevier B.V. All rights reserved.......Numerical homogenization is an efficient way to determine effective macroscopic properties, such as the elasticity tensor, of a periodic composite material. In this paper an educational description of the method is provided based on a short, self-contained Matlab implementation. It is shown how...... the basic code, which computes the effective elasticity tensor of a two material composite, where one material could be void, is easily extended to include more materials. Furthermore, extensions to homogenization of conductivity, thermal expansion, and fluid permeability are described in detail. The unit...

  10. Biologic properties of surgical scaffold materials derived from dermal ECM.

    Science.gov (United States)

    Kulig, Katherine M; Luo, Xiao; Finkelstein, Eric B; Liu, Xiang-Hong; Goldman, Scott M; Sundback, Cathryn A; Vacanti, Joseph P; Neville, Craig M

    2013-07-01

    Surgical scaffold materials manufactured from donor human or animal tissue are increasingly being used to promote soft tissue repair and regeneration. The clinical product consists of the residual extracellular matrix remaining after a rigorous decellularization process. Optimally, the material provides both structural support during the repair period and cell guidance cues for effective incorporation into the regenerating tissue. Surgical scaffold materials are available from several companies and are unique products manufactured by proprietary methodology. A significant need exists for a more thorough understanding of scaffold properties that impact the early steps of host cell recruitment and infiltration. In this study, a panel of in vitro assays was used to make direct comparisons of several similar, commercially-available materials: Alloderm, Medeor Matrix, Permacol, and Strattice. Differences in the materials were detected for both cell signaling and scaffold architecture-dependent cell invasion. Material-conditioned media studies found Medeor Matrix to have the greatest positive effect upon cell proliferation and induction of migration. Strattice provided the greatest chemotaxis signaling and best suppressed apoptotic induction. Among assays measuring structure-dependent properties, Medeor Matrix was superior for cell attachment, followed by Permacol. Only Alloderm and Medeor Matrix supported chemotaxis-driven cell invasion beyond the most superficial zone. Medeor Matrix was the only material in the chorioallantoic membrane assay to support substantial cell invasion. These results indicate that both biologic and structural properties need to be carefully assessed in the considerable ongoing efforts to develop new uses and products in this important class of biomaterials. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Temporal properties of material categorization and material rating: visual vs non-visual material features.

    Science.gov (United States)

    Nagai, Takehiro; Matsushima, Toshiki; Koida, Kowa; Tani, Yusuke; Kitazaki, Michiteru; Nakauchi, Shigeki

    2015-10-01

    Humans can visually recognize material categories of objects, such as glass, stone, and plastic, easily. However, little is known about the kinds of surface quality features that contribute to such material class recognition. In this paper, we examine the relationship between perceptual surface features and material category discrimination performance for pictures of materials, focusing on temporal aspects, including reaction time and effects of stimulus duration. The stimuli were pictures of objects with an identical shape but made of different materials that could be categorized into seven classes (glass, plastic, metal, stone, wood, leather, and fabric). In a pre-experiment, observers rated the pictures on nine surface features, including visual (e.g., glossiness and transparency) and non-visual features (e.g., heaviness and warmness), on a 7-point scale. In the main experiments, observers judged whether two simultaneously presented pictures were classified as the same or different material category. Reaction times and effects of stimulus duration were measured. The results showed that visual feature ratings were correlated with material discrimination performance for short reaction times or short stimulus durations, while non-visual feature ratings were correlated only with performance for long reaction times or long stimulus durations. These results suggest that the mechanisms underlying visual and non-visual feature processing may differ in terms of processing time, although the cause is unclear. Visual surface features may mainly contribute to material recognition in daily life, while non-visual features may contribute only weakly, if at all.

  12. Microstructure characterization and magnetic properties of nano structured materials

    Energy Technology Data Exchange (ETDEWEB)

    Sun, X.C

    2000-07-01

    The present thesis deals with the unique microstructural properties and their novel magnetic properties of core-shell Ni-Ce nano composite particles, carbon encapsulated Fe, Co, and Ni nanoparticles and the nano crystallization behavior of typical ferromagnetic Fe{sub 78}Si{sub 9}B{sub 13} ribbons. These properties have intensively been investigated by high resolution transmission electron microscopy (HREM), X-ray diffraction (XRD), scanning electron microscopy (Sem), X-ray energy dispersive spectroscopy [eds.]; selected area electron diffraction pattern (SAED), Ft-IR, differential scanning calorimeter (DSC). In addition, magnetic moments measurements at different temperatures and applied fields have been performed by transmission Moessbauer spectroscopy, superconducting quantum interference device magnetometer (SQUID), and vibrating sample magnetometer (VSM). The present studies may provide the insights for the better understanding of the correlation between the unique microstructure and novel magnetic properties for several magnetic nano structured materials. (Author)

  13. Material Properties of High-Speed Steel Rolls

    Directory of Open Access Journals (Sweden)

    Shaohua Wu

    2017-03-01

    Full Text Available Recently, it has been required to improve the material properties of high-speed steel (HSS rolls, because of the low wear resistance and low mechanical properties. To improve them, several new steels have been proposed, which have high wear resistance as well as excellent mechanical properties, e.g., hardness and tensile properties, where additional elements (V, Cr and W were employed. However, their steels may have still technical issues, as the roll surfaces become roughened during the production process. The reason for this problem is found to be affected by the oxidation of the HSS surface. In this work, we have provided the suggestions to make high wear resistance of the HSS rolls

  14. Homogenization for Periodic Heterogeneous Materials with Arbitrary Position-Dependent Material Properties

    Institute of Scientific and Technical Information of China (English)

    徐志杰

    2012-01-01

    We present a rigorous homogenization approach for elcient computation of a class of physical problems in a one-dimensional periodic heterogeneous material. This material is represented by a spatially periodic array of unit cells with a length of More specifically, the method is applied to the diffusion, heat conduction, and wave propagation problems. Heterogeneous materials can have arbitrary position-dependent continuous or discontinuous materials properties (for example heat conductivity) within the unit cell. The final effective model includes both effective properties at the leading order and high-order contributions due to the microscopic heterogeneity. A dimensionless heterogeneity parameter ~ is defined to represent high-order contributions, shown to be in the range of [-1/12, 0], and has a universal expression for all three problems. Both effective properties and heterogeneity parameter 13 are independent oft, the microscopic scale of heterogeneity. The homogenized solution describing macroscopic variations can be obtained from the effective model. Solution with sub-unit-cell accuracy can be constructed based on the homogenized solution and its spatial derivatives. The paper represents a general approach to obtain the effective model for arbitrary periodic heterogeneous materials with position-dependent properties.

  15. Rectangular waveguide material characterization: anisotropic property extraction and measurement validation

    Science.gov (United States)

    Crowgey, Benjamin Reid

    for characterization of a sample filling the cross-section of a waveguide. Due to the rectangular nature of the waveguide, typically three different samples are manufactured from the same material in order to characterize the six complex material parameters. The second technique for measuring the electromagnetic properties of a biaxially anisotropic material sample uses a reduced-aperture waveguide sample holder designed to accommodate a cubical sample. All the tensor material parameters can then be determined by measuring the reflection and transmission coefficients of a single sample placed into several orientations. The parameters are obtained using a root-searching algorithm by comparing theoretically computed and measured reflection and transmission coefficients. The theoretical coefficients are determined using a mode matching technique. The first technique for characterizing the electromagnetic properties of gyromagnetic materials considers requires filling the cross-section of a waveguide. The material parameters are extracted from the measured reflection and transmission coefficients. Since the cross-sectional dimensions of waveguides become prohibitively large at low frequencies, and it is at these frequencies that the gyromagnetic properties are most pronounced, sufficiently large samples may not be available. Therefore, the second technique uses a reduced-aperture sample holder that does not require the sample to fill the entire cross section of the guide. The theoretical reflection and transmission coefficients for both methods are determined using a mode matching technique. A nonlinear least squares method is employed to extract the gyromagnetic material parameters. Finally, this dissertation introduces a waveguide standard that acts as a surrogate material with both electric and magnetic properties and is useful for verifying systems designed to characterize engineered materials using the NRW technique. A genetic algorithm is used to optimize the all

  16. Further developments in material properties determined by vibration analysis

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang; Andreasen, Lotte; Seifert, Mette

    1997-01-01

    have been studied by testing a number of building materials. The method has been PC-integrated with the Brüel & Kjær's type 3550 vibration equipment - and special user menus have been developed to facilitate handling of the method in practice. Limits on range of test frequencies applied are discussed...... with respect to configurations of vibration equipment and shapes of test specimens used. Sensitivity studies have been made to identify sources of errors which may disturb the reliability of the method used in practice. Practical aspects with respect to test set-ups are considered in these studies - as well......A method was described in Materialnyt 1 (1995) on "Material properties determined by vibration analysis". This new method of materials testing has been further developed as the result of research at the Building Materials Laboratory, Technical University of Denmark.Practical aspects of the method...

  17. Correlation of macroscopic material properties with microscopic nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Simons, R.L.

    1981-12-18

    Two primary irradiation-induced changes occur during neutron irradiation: the displacement of atoms forming crystal defects and the transmutation of atoms into either gaseous or solid products. The material scientist studying irradiation damage to material by fusion-produced neutrons is faced with several questions: Is the nature of high-energy (14-MeV) displacement damage the same as or different from that caused by fission neutrons (< 2 MeV). How do the high helium concentrations expected in a fusion environment affect the material properties. What effects do solid transmutation products have on the behavior of the irradiated materials. In the past few years, much work has been done to answer these questions. This paper reviews recent work in this area.

  18. Thermal property of insulation material for HTS power cable

    Science.gov (United States)

    Choi, Yeon Suk; Kim, D. L.; Shin, D. W.; Hwang, S. D.

    2012-06-01

    The thermal property of insulation material is essential in developing a high temperature superconductor (HTS) power cable operating at around liquid nitrogen temperature. The accurate estimate of the heat flux is difficult in the nonmetallic materials because nonmetallic materials have a high thermal resistance and low temperature gradient along the specimen. The objective of the present work is to develop a precise instrument for measuring the thermal conductivity of insulating materials over a temperature range of 30 K to approximately the room temperature by using a cryocooler. The thermal conductivity of Teflon is measured and the accuracy confirmation is carried out by comparing published data. In addition, the experimental results of apparent thermal conductivity of polypropylene laminated paper (PPLP) are presented and the temperature dependency is also discussed

  19. Alkali-activated cementitious materials: Mechanisms, microstructure and properties

    Science.gov (United States)

    Jiang, Weimin

    The goal of this study was to examine the activation reaction, microstructure, properties, identify the mechanisms of activation, and achieve an enhanced understanding of activation processes occurring during the synthesis of alkali activated cementitious materials (AAC). The discussions classify the following categories. (1) alkali activated slag cement; (2) alkali activated portland-slag cement; (3) alkali activated fly ash-slag cement; (4) alkali activated pozzolana-lime cement; (5) alkali activated pozzolana cement. The activators involved are NaOH, KOH; Nasb2SOsb4;\\ Nasb2COsb3;\\ CaSOsb4, and soluble silicate of sodium and potassium. The effect of alkali activation on the microstructure of these materials were analyzed at the micro-nanometer scale by SEM, EDS, ESEM, and TEM. Also sp{29}Si and sp{27}Al MAS-NMR, IR, Raman, TGA, and DTA were performed to characterize the phase in these systems. Slag, fly ash, silica fume, as well as blended cements containing mixtures of these and other components were characterized. A set of ordinary portland cement paste samples served as a control. This study confirmed that AAC materials have great potential because they could generate very early high strength, greater durability and high performance. Among the benefits to be derived from this research is a better understanding of the factors that control concrete properties when using AAC materials, and by controlling the chemistry and processing to produce desired microstructures and properties, as well as their durability.

  20. Mechanical Properties of Calcium Fluoride-Based Composite Materials

    Science.gov (United States)

    Kleczewska, Joanna; Pryliński, Mariusz; Podlewska, Magdalena; Sokołowski, Jerzy; Łapińska, Barbara

    2016-01-01

    Aim of the study was to evaluate mechanical properties of light-curing composite materials modified with the addition of calcium fluoride. The study used one experimental light-curing composite material (ECM) and one commercially available flowable light-curing composite material (FA) that were modified with 0.5–5.0 wt% anhydrous calcium fluoride. Morphology of the samples and uniformity of CaF2 distribution were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). Mechanical properties were tested after 24-hour storage of specimens in dry or wet conditions. Stored dry ECM enriched with 0.5–1.0 wt% CaF2 showed higher tensile strength values, while water storage of all modified ECM specimens decreased their tensile strength. The highest Vickers hardness tested after dry storage was observed for 2.5 wt% CaF2 content in ECM. The addition of 2.0–5.0 wt% CaF2 to FA caused significant decrease in tensile strength after dry storage and overall tensile strength decrease of modified FA specimens after water storage. The content of 2.0 wt% CaF2 in FA resulted in the highest Vickers hardness tested after wet storage. Commercially available composite material (FA), unmodified with fluoride addition, demonstrated overall significantly higher mechanical properties. PMID:28004001

  1. Mechanical Properties of Calcium Fluoride-Based Composite Materials

    Directory of Open Access Journals (Sweden)

    Monika Łukomska-Szymańska

    2016-01-01

    Full Text Available Aim of the study was to evaluate mechanical properties of light-curing composite materials modified with the addition of calcium fluoride. The study used one experimental light-curing composite material (ECM and one commercially available flowable light-curing composite material (FA that were modified with 0.5–5.0 wt% anhydrous calcium fluoride. Morphology of the samples and uniformity of CaF2 distribution were analyzed using Scanning Electron Microscopy (SEM and Energy Dispersive Spectroscopy (EDS. Mechanical properties were tested after 24-hour storage of specimens in dry or wet conditions. Stored dry ECM enriched with 0.5–1.0 wt% CaF2 showed higher tensile strength values, while water storage of all modified ECM specimens decreased their tensile strength. The highest Vickers hardness tested after dry storage was observed for 2.5 wt% CaF2 content in ECM. The addition of 2.0–5.0 wt% CaF2 to FA caused significant decrease in tensile strength after dry storage and overall tensile strength decrease of modified FA specimens after water storage. The content of 2.0 wt% CaF2 in FA resulted in the highest Vickers hardness tested after wet storage. Commercially available composite material (FA, unmodified with fluoride addition, demonstrated overall significantly higher mechanical properties.

  2. Dynamic properties of liquid Ni revisited

    Directory of Open Access Journals (Sweden)

    del Rio B. G.

    2017-01-01

    Full Text Available Liquid Ni has previously been studied by different approaches such as molecular dynamics simulations and experimental techniques including inelastic neutron and X-ray scattering. Although some puzzling results, such as the shape of the sound dispersion curve for q ≤ 1.0 Å−1, have already been sorted out, there still persist some discrepancies, among different studies, for greater q-values. We have performed ab initio simulation calculations which show how those differences can be reconciled. Moreover, we have found that the transverse current spectral functions have some features which, so far, had previously been shown by high pressure liquid metals.

  3. Estimating Energy Conversion Efficiency of Thermoelectric Materials: Constant Property Versus Average Property Models

    Science.gov (United States)

    Armstrong, Hannah; Boese, Matthew; Carmichael, Cody; Dimich, Hannah; Seay, Dylan; Sheppard, Nathan; Beekman, Matt

    2017-01-01

    Maximum thermoelectric energy conversion efficiencies are calculated using the conventional "constant property" model and the recently proposed "cumulative/average property" model (Kim et al. in Proc Natl Acad Sci USA 112:8205, 2015) for 18 high-performance thermoelectric materials. We find that the constant property model generally predicts higher energy conversion efficiency for nearly all materials and temperature differences studied. Although significant deviations are observed in some cases, on average the constant property model predicts an efficiency that is a factor of 1.16 larger than that predicted by the average property model, with even lower deviations for temperature differences typical of energy harvesting applications. Based on our analysis, we conclude that the conventional dimensionless figure of merit ZT obtained from the constant property model, while not applicable for some materials with strongly temperature-dependent thermoelectric properties, remains a simple yet useful metric for initial evaluation and/or comparison of thermoelectric materials, provided the ZT at the average temperature of projected operation, not the peak ZT, is used.

  4. Elastic therapeutic tape: do they have the same material properties?

    Science.gov (United States)

    Boonkerd, Chuanpis; Limroongreungrat, Weerawat

    2016-01-01

    [Purpose] Elastic therapeutic tape has been widely used for rehabilitation and treatment of sports injuries. Tapes with different elastic properties serve different treatment purposes with inappropriate tension reducing tape effectiveness. Many tapes are available in the market, but studies on tape properties are limited. The aim of this study was to examine the material properties of elastic therapeutic tape. [Subjects and Methods] Brands of elastic therapeutic tape included KinesioTex®, ATex, Mueller, 3M, and ThaiTape. The Material Testing System Insight® 1 Electromechanical Testing Systems was used to apply a tensile force on elastic therapeutic tape. Ten specimens of each brand were tested. Stress, load, and Young’s modulus at 25%, 50%, 75%, 100%, and maximum point were collected. One-way analysis of variance with post hoc testing was used to analyze tape parameters. [Results] Maximum elongation and Young’s modulus at all percentages were significantly different between brands. There were no differences in maximum load and maximum stress. [Conclusion] Mechanical properties are different for commercial elastic therapeutic tapes. Physiotherapists and other clinicians should be aware of mechanical tape properties to correctly apply kinesio tape. PMID:27190472

  5. Elastic therapeutic tape: do they have the same material properties?

    Science.gov (United States)

    Boonkerd, Chuanpis; Limroongreungrat, Weerawat

    2016-04-01

    [Purpose] Elastic therapeutic tape has been widely used for rehabilitation and treatment of sports injuries. Tapes with different elastic properties serve different treatment purposes with inappropriate tension reducing tape effectiveness. Many tapes are available in the market, but studies on tape properties are limited. The aim of this study was to examine the material properties of elastic therapeutic tape. [Subjects and Methods] Brands of elastic therapeutic tape included KinesioTex(®), ATex, Mueller, 3M, and ThaiTape. The Material Testing System Insight(®) 1 Electromechanical Testing Systems was used to apply a tensile force on elastic therapeutic tape. Ten specimens of each brand were tested. Stress, load, and Young's modulus at 25%, 50%, 75%, 100%, and maximum point were collected. One-way analysis of variance with post hoc testing was used to analyze tape parameters. [Results] Maximum elongation and Young's modulus at all percentages were significantly different between brands. There were no differences in maximum load and maximum stress. [Conclusion] Mechanical properties are different for commercial elastic therapeutic tapes. Physiotherapists and other clinicians should be aware of mechanical tape properties to correctly apply kinesio tape.

  6. Analysis of Mechanical Properties of Fabrics of Different Raw Material

    Directory of Open Access Journals (Sweden)

    Aušra ADOMAITIENĖ

    2011-07-01

    Full Text Available The study analyzes dependence of mechanical properties (breaking force, elongation at break, static friction force and static friction coefficient on integrated fabric structure factor j and raw material density r, among the fabrics of different raw material (cotton, wool, polypropylene, polyester and polyacrylnitrile and woven in different conditions. The received results demonstrate that sometimes strong dependences exist (wool, polypropylene and polyacrylnitrile, whereas in some cases (cotton and polyester there is no correlation. It was also discovered that the breaking force and elongation at break in the direction of weft increase, when fabric structure becomes more rigid. In the meantime variations of the curves in the direction of warp are insignificant. Regarding static friction force and static friction coefficient (found in two cases, when fabrics were rubbing against leather and materials, it was discovered that consistency of the curves is irregular, i. e. they either increase or decrease, when integrated fabric structure factor j growth. It was also identified that some dependences are not strong and relationship between explored and analyzed factors does not exist. Variation of all these mechanical properties with respect to material density r enables to conclude that increase of material density r results in poor dependences or they are whatsoever non-existent.http://dx.doi.org/10.5755/j01.ms.17.2.487

  7. Preparation and Properties of Orthogonal Piezoelectric Composite Materials

    Institute of Scientific and Technical Information of China (English)

    Liu Jun; Lu Ying; Zhang Xingguo; Shen Yi; Chen Chun

    2004-01-01

    . PZT piezoelectric ceramic with La2O3, SrCO3, BaO and Sb2O5 was prepared. It has high value of the piezoelectric strain constant d33 ( -681 PC/N) and high value of-d33/d31 (2.65). Orthogonal piezoelectric composite materials was designed and prepared by PZT, DAD- 40 electric conductive adhesive and E51 epoxy resin. The OPCM shows obvious orthogonal anisotropy. The matching property of the interface between piezoelectric ceramic and polymer of OPCM relies on the defects of interface. The proper conductive mid-layer could improve the matching property of the interface.

  8. Thermophysical properties of new materials; Proprietes thermophysiques des materiaux nouveaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This conference day was organized by the `thermo-kinetics` section of the French association of thermal engineers. This book of proceedings contains 5 papers entitled: `characterization of thermal properties using periodical methods at the Odeillo test centre: developments and applications`; `measurement of the distribution of local thermophysical properties by IR images processing and averaging technique`; `extension of shock probes to the characterization of multi-layers - development of a simple device for the characterization of insulating materials or shear fluids`; `thermal local diffusivity of constituents of carbon/carbon composites`; `new method for the thermal diffusivity measurement of thermo-hardenable resins during polymerization`. (J.S.)

  9. Structure/property relationships in non-linear optical materials

    Energy Technology Data Exchange (ETDEWEB)

    Cole, J.M. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)]|[Durham Univ. (United Kingdom); Howard, J.A.K. [Durham Univ. (United Kingdom); McIntyre, G.J. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1997-04-01

    The application of neutrons to the study of structure/property relationships in organic non-linear optical materials (NLOs) is described. In particular, charge-transfer effects and intermolecular interactions are investigated. Charge-transfer effects are studied by charge-density analysis and an example of one such investigation is given. The study of intermolecular interactions concentrates on the effects of hydrogen-bonding and an example is given of two structurally similar molecules with very disparate NLO properties, as a result of different types of hydrogen-bonding. (author). 3 refs.

  10. Simulated Analysis of Dielectric Properties of Heterogeneous Materials

    Directory of Open Access Journals (Sweden)

    Yang Biao

    2016-01-01

    Full Text Available The present paper reports the results of a numerical analysis of two phases lossless heterogeneous materials based on a three dimensional (3-D random dielectric mixture. The effective permittivity of a 3-D dielectric materials is calculated by the S-parameter retrieval method and finite element method. The calculated effective permittivity is in good agreement with theoretical models by compared with Bruggeman formula and Coherent potential formula, showing that the volume fraction of inclusions is increasing, the effective permittivity increases with radiation frequency and appear an imaginary part taking on the dielectric loss properties.

  11. Relationships between fracture toughness and other material properties. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Perra, M.; Finnie, I.

    1974-01-01

    The key experimental and analytical studies which have led to our present understanding of the mechanisms of ductile fracture are reviewed. It is concluded that insufficient progress has been made in the quantitative description of ductile separation mechanisms on a microscale to allow the realistic prediction of fracture toughness from material properties and microstructure. An experimental study of ductile fracture is underway which has the aim of determining the growth rate of voids in known plastic deformation fields as a function of triaxiality of stress and material work-hardening. Novel specimens of particularly well characterized microstructure are utilized.

  12. Real-time probing of structural dynamics in perovskite materials

    Energy Technology Data Exchange (ETDEWEB)

    Elsaesser, Thomas [Max-Born-Institut fuer Nichtlineare Optik und Kurzzeitspektroskopie, D-12489 Berlin (Germany)

    2009-07-01

    Femtosecond x-ray diffraction probes structural dynamics of solids in real-time and gives insight into reversible geometry changes on atomic length and time scales. After a brief introduction into this field, recent results on the lattice dynamics of ferroelectric SrRuO{sub 3}/PbZr{sub 0.2}Ti{sub 0.8}O{sub 3} superlattice structures and their interplay with the electric polarization of the material are presented. Ultrafast optical generation of mechanical stress allows for switching-off the polarization on a time scale of a few picoseconds. As a second example, magnetostriction in a ferromagnetic SrRuO{sub 3}/SrTiO{sub 3} superlattice structure is analyzed in real time.

  13. Dynamic properties of power MOS transistors

    Science.gov (United States)

    Belabadia, Mohammed

    Power MOSFET's were modeled in dynamic high frequency and switching regimes, based on a theoretical analysis of the active region, taking into account the short channel effects and those related to structural configuration elements. The theoretical synthesis of intrinsic and parasitic elements leads to a complete nonlinear physical model compatible with electric simulators. The model is used for simulation and computer aided design of electric circuits which use power MOSFET's such as RF amplifiers, and frequency doublers. For the switching regime, a hierarchy of models for power V.DMOS transistors is developed. Two compact models consistent with SPICE-2 program and well suited for study and characterization of power V.DMOSFET, in switching condition under resistive and inductive loads, are proposed. They can describe low, medium, and high voltage structures.

  14. Peculiar dynamical properties of plutonium hydrides

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In the present work, the structure and spectra of PuH and PuH2 are defined by B3LYP/SDD method, from which the analytic potential energy function of PuH2 is derived. The analysis of quasi-classical molecular reaction dynamics is performed to study the state-state process of pu(7Fg) + H2(X1∑+g ). It is found that the reaction pu(7Fg) + H2(X1∑+g )→PuH2(X7B1) has no threshold. The simultaneous hydrogenation process of plutonium with the main product of PuH2 is theoretically proved for the first time.

  15. Mechanical properties in crumple-formed paper derived materials subjected to compression

    Directory of Open Access Journals (Sweden)

    D.A.H. Hanaor

    2017-06-01

    Full Text Available The crumpling of precursor materials to form dense three dimensional geometries offers an attractive route towards the utilisation of minor-value waste materials. Crumple-forming results in a mesostructured system in which mechanical properties of the material are governed by complex cross-scale deformation mechanisms. Here we investigate the physical and mechanical properties of dense compacted structures fabricated by the confined uniaxial compression of a cellulose tissue to yield crumpled mesostructuring. A total of 25 specimens of various densities were tested under compression. Crumple formed specimens exhibited densities in the range 0.8–1.3 g cm−3, and showed high strength to weight characteristics, achieving ultimate compressive strength values of up to 200 MPa under both quasi-static and high strain rate loading conditions and deformation energy that compares well to engineering materials of similar density. The materials fabricated in this work and their mechanical attributes demonstrate the potential of crumple-forming approaches in the fabrication of novel energy-absorbing materials from low-cost precursors such as recycled paper. Stiffness and toughness of the materials exhibit density dependence suggesting this forming technique further allows controllable impact energy dissipation rates in dynamic applications.

  16. Effective Materials Property Information Management for the 21st Century

    Science.gov (United States)

    Ren, Weiju; Cebon, David; Arnold, Steve

    2009-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fueled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the need for consistency, quality and traceability of data, as well as control of access to sensitive information such as proprietary data. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single "gold source" of materials information between members of global engineering teams in extended supply chains. Fortunately, material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data "pedigree" traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  17. Effective Materials Property Information Management for the 21st Century

    Science.gov (United States)

    Ren, Weiju; Cebon, David; Arnold, Steve

    2009-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fueled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the need for consistency, quality and traceability of data, as well as control of access to sensitive information such as proprietary data. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single "gold source" of materials information between members of global engineering teams in extended supply chains. Fortunately, material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data "pedigree" traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  18. Effective Materials Property Information Management for the 21st Century

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Weiju [ORNL; Cebon, David [Cambridge University; Barabash, Oleg M [ORNL

    2011-01-01

    This paper discusses key principles for the development of materials property information management software systems. There are growing needs for automated materials information management in various organizations. In part these are fuelled by the demands for higher efficiency in material testing, product design and engineering analysis. But equally important, organizations are being driven by the needs for consistency, quality and traceability of data, as well as control of access to proprietary or sensitive information. Further, the use of increasingly sophisticated nonlinear, anisotropic and multi-scale engineering analyses requires both processing of large volumes of test data for development of constitutive models and complex materials data input for Computer-Aided Engineering (CAE) software. And finally, the globalization of economy often generates great needs for sharing a single gold source of materials information between members of global engineering teams in extended supply-chains. Fortunately material property management systems have kept pace with the growing user demands and evolved to versatile data management systems that can be customized to specific user needs. The more sophisticated of these provide facilities for: (i) data management functions such as access, version, and quality controls; (ii) a wide range of data import, export and analysis capabilities; (iii) data pedigree traceability mechanisms; (iv) data searching, reporting and viewing tools; and (v) access to the information via a wide range of interfaces. In this paper the important requirements for advanced material data management systems, future challenges and opportunities such as automated error checking, data quality characterization, identification of gaps in datasets, as well as functionalities and business models to fuel database growth and maintenance are discussed.

  19. Optical properties of glazing materials at normal incidence

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, M.; Powles, R.

    2001-10-01

    Measurements of spectral transmittance T and reflectance R at normal incidence continue to be the most common and accurate source of energy performance data for glazing materials. Prediction of these radiometric properties from more fundamental materials data is often confounded by the complexity and uncertainty of coating structures. Angle-dependent radiometric properties of coated glazing will probably be predicted from normal-incidence data rather than being measured at many angles. The general error level demonstrated in round-robin tests is on the order 1-2%; it is often necessary to achieve better levels of performance. Based on results obtained following the round-robin tests, it is expected that accuracy of better than 0.5% can be generally achieved. A new type of absolute standard reference is described and tested with promising results.

  20. New Technique for Evaluating Adhesion Properties between Soft Materials

    Science.gov (United States)

    Sato, Takaya; Goto, Motoaki; Nakano, Ken; Suzuki, Atsushi

    2005-11-01

    A new, simple apparatus for measuring the surface adhesion properties of soft materials was designed, where the adhesion force of a point contact between soft materials and the total energy required to separate the contact can be measured using the springs of phosphor-bronze thin plates with strain gauges. The adhesion between swollen hydrogels was studied here by this simple technique in air at room temperature. The gels used in the present preliminary experiments were poly(sodium acrylate) hydrogels physically cross-linked by aluminum ions. The adhesion force and the separation energy showed a power-law increase with separation velocity. The apparatus was applied to evaluate the adhesion properties of seven anti-inflammatory analgesic cataplasms on the market. It was found that the easiness to separate (rank of adhesion force and the separation energy) was consistent with the results of those obtained by organoleptic evaluations.

  1. Textile Materials with New Properties Used for Confections Manufacturing

    Directory of Open Access Journals (Sweden)

    Neacşu A. N.

    2009-12-01

    Full Text Available The quality of textile clothing depends on the quality of prime materials and also on the technology used; this must ensure a balance between transferred heat, resulted humidity and human and environmental thermal demands, all this bringing about physiological comfort. In order to meet consumers’ demands regarding the production of products which are easy to maintain and have high hygiene properties, new prime materials are searched, with a view to ensuring a wide range of clothing. Taking into consideration the acceleration of changes and the global inter-connections, a company must develop its capacity of innovation in order to bring products with new properties on the market before others do.

  2. Shearographic System for Dynamic Analysis of Materials under Heat Stress

    Directory of Open Access Journals (Sweden)

    Nelson A. Correa-Rojas

    2013-11-01

    Full Text Available Shearography is a tool for monitoring and inspecting of structural flaws and imperfections in different types of industrial, automotive and aeronautics applications. It is based on digital correlation of two speckle patterns in two states of interest: with and without load. The technique has the special quality of being very robust against environmental disturbances. We present a shearographic system to analyze the dynamic behavior of the strain that suffers a material in response to changes in temperature throughout the thermal load process.

  3. Determination of thermal properties of composting bulking materials.

    Science.gov (United States)

    Ahn, H K; Sauer, T J; Richard, T L; Glanville, T D

    2009-09-01

    Thermal properties of compost bulking materials affect temperature and biodegradation during the composting process. Well determined thermal properties of compost feedstocks will therefore contribute to practical thermodynamic approaches. Thermal conductivity, thermal diffusivity, and volumetric heat capacity of 12 compost bulking materials were determined in this study. Thermal properties were determined at varying bulk densities (1, 1.3, 1.7, 2.5, and 5 times uncompacted bulk density), particle sizes (ground and bulk), and water contents (0, 20, 50, 80% of water holding capacity and saturated condition). For the water content at 80% of water holding capacity, saw dust, soil compost blend, beef manure, and turkey litter showed the highest thermal conductivity (K) and volumetric heat capacity (C) (K: 0.12-0.81 W/m degrees C and C: 1.36-4.08 MJ/m(3) degrees C). Silage showed medium values at the same water content (K: 0.09-0.47 W/m degrees C and C: 0.93-3.09 MJ/m(3) degrees C). Wheat straw, oat straw, soybean straw, cornstalks, alfalfa hay, and wood shavings produced the lowest K and C values (K: 0.03-0.30 W/m degrees C and C: 0.26-3.45 MJ/m(3) degrees C). Thermal conductivity and volumetric heat capacity showed a linear relationship with moisture content and bulk density, while thermal diffusivity showed a nonlinear relationship. Since the water, air, and solid materials have their own specific thermal property values, thermal properties of compost bulking materials vary with the rate of those three components by changing water content, bulk density, and particle size. The degree of saturation was used to represent the interaction between volumes of water, air, and solids under the various combinations of moisture content, bulk density, and particle size. The first order regression models developed in this paper represent the relationship between degree of saturation and volumetric heat capacity (r=0.95-0.99) and thermal conductivity (r=0.84-0.99) well. Improved

  4. Models for acoustical properties of green roof materials

    OpenAIRE

    2011-01-01

    To predict the acoustical effects of green roof structures it is necessary to be able to model the acoustical properties of their materials including gravel. For time domain calculations it is convenient to use the phenomenological model due to Zwikker and Kosten. However this phenomenological model is related to a low frequency/high flow resistivity approximation of more ‘exact’ identical pore models. The results of fitting predictions to short range level difference data and to impedance da...

  5. Sorbent Material Property Requirements for On-Board Hydrogen Storage for Automotive Fuel Cell Systems.

    Energy Technology Data Exchange (ETDEWEB)

    Ahluwalia, R. K.; Peng, J-K; Hua, T. Q.

    2015-05-25

    Material properties required for on-board hydrogen storage in cryogenic sorbents for use with automotive polymer electrolyte membrane (PEM) fuel cell systems are discussed. Models are formulated for physical, thermodynamic and transport properties, and for the dynamics of H-2 refueling and discharge from a sorbent bed. A conceptual storage configuration with in-bed heat exchanger tubes, a Type-3 containment vessel, vacuum insulation and requisite balance-of-plant components is developed to determine the peak excess sorption capacity and differential enthalpy of adsorption for 5.5 wt% system gravimetric capacity and 55% well-to-tank (WTT) efficiency. The analysis also determines the bulk density to which the material must be compacted for the storage system to reach 40 g.L-1 volumetric capacity. Thermal transport properties and heat transfer enhancement methods are analyzed to estimate the material thermal conductivity needed to achieve 1.5 kg.min(-1) H-2 refueling rate. Operating temperatures and pressures are determined for 55% WTT efficiency and 95% usable H-2. Needs for further improvements in material properties are analyzed that would allow reduction of storage pressure to 50 bar from 100 bar, elevation of storage temperature to 175-200 K from 150 K, and increase of WTT efficiency to 57.5% or higher.

  6. The effect of material properties on the seismic performance of Arch Dams

    Science.gov (United States)

    Sevim, B.

    2011-08-01

    The paper investigates the effect of material properties on the seismic performance of arch dam-reservoir-foundation interaction systems based on the Lagrangian approach using demand-capacity ratios. Type-5 arch dam is selected as a numerical application. The linear time history analyses of the arch dam-reservoir-foundation interaction system are carried out for different material properties. The foundation is taken into account as massless; behaviour of the reservoir is assumed to be linearly elastic, inviscid and irrotational. The north-south component of the Erzincan earthquake in 1992 is chosen as a ground motion. Dynamic equations of motions obtained from 3-D finite element modelling of the coupled system are solved by using the Newmark integration algorithm. The damage levels of the coupled system for the different material properties are demonstrated by using demand-capacity ratios and cumulative inelastic durations. The time histories and maximum values of the displacements and principal stresses, and performance curves, are obtained from linear analyses. It is clearly seen from the study that the different material properties affect the seismic behaviour of the dam.

  7. Molecular Dynamics Simulation on thermodynamic Properties and Transport Coefficients

    Institute of Scientific and Technical Information of China (English)

    D.X.Xiong

    1996-01-01

    Moecular dynamics simulation (MDS) is used to study the thermodynamic properties and transport coefficients of an argon system with Lennend-Jones potential.The results on the velocity distribution,mean free path,mean collison time,specific heat and self0diffusion coefficient agree well with the existing theoretical /experimental data,It shows that molecular dynamics method is another bridge to connect microworld and macreoworld.

  8. Ocean acidification alters the material properties of Mytilus edulis shells.

    Science.gov (United States)

    Fitzer, Susan C; Zhu, Wenzhong; Tanner, K Elizabeth; Phoenix, Vernon R; Kamenos, Nicholas A; Cusack, Maggie

    2015-02-01

    Ocean acidification (OA) and the resultant changing carbonate saturation states is threatening the formation of calcium carbonate shells and exoskeletons of marine organisms. The production of biominerals in such organisms relies on the availability of carbonate and the ability of the organism to biomineralize in changing environments. To understand how biomineralizers will respond to OA the common blue mussel, Mytilus edulis, was cultured at projected levels of pCO2 (380, 550, 750, 1000 µatm) and increased temperatures (ambient, ambient plus 2°C). Nanoindentation (a single mussel shell) and microhardness testing were used to assess the material properties of the shells. Young's modulus (E), hardness (H) and toughness (KIC) were measured in mussel shells grown in multiple stressor conditions. OA caused mussels to produce shell calcite that is stiffer (higher modulus of elasticity) and harder than shells grown in control conditions. The outer shell (calcite) is more brittle in OA conditions while the inner shell (aragonite) is softer and less stiff in shells grown under OA conditions. Combining increasing ocean pCO2 and temperatures as projected for future global ocean appears to reduce the impact of increasing pCO2 on the material properties of the mussel shell. OA may cause changes in shell material properties that could prove problematic under predation scenarios for the mussels; however, this may be partially mitigated by increasing temperature.

  9. Characterization of ion-exchange membrane materials: properties vs structure.

    Science.gov (United States)

    Berezina, N P; Kononenko, N A; Dyomina, O A; Gnusin, N P

    2008-06-22

    This review focuses on the preparation, structure and applications of ion-exchange membranes formed from various materials and exhibiting various functions (electrodialytic, perfluorinated sulphocation-exchange and novel laboratory-tested membranes). A number of experimental techniques for measuring electrotransport properties as well as the general procedure for membrane testing are also described. The review emphasizes the relationships between membrane structures, physical and chemical properties and mechanisms of electrochemical processes that occur in charged membrane materials. The water content in membranes is considered to be a key factor in the ion and water transfer and in polarization processes in electromembrane systems. We suggest the theoretical approach, which makes it possible to model and characterize the electrochemical properties of heterogeneous membranes using several transport-structural parameters. These parameters are extracted from the experimental dependences of specific electroconductivity and diffusion permeability on concentration. The review covers the most significant experimental and theoretical research on ion-exchange membranes that have been carried out in the Membrane Materials Laboratory of the Kuban State University. These results have been discussed at the conferences "Membrane Electrochemistry", Krasnodar, Russia for many years and were published mainly in Russian scientific sources.

  10. Thermophysical Properties of Automotive Metallic Brake Disk Materials

    Science.gov (United States)

    Kim, S. W.; Park, K.; Lee, S. H.; Kang, K. H.; Lim, K. T.

    2008-12-01

    The temperature distribution, the thermal deformation, and the thermal stress of automotive brake disks have quite close relations with car safety; therefore, much research in this field has been performed. However, successful and satisfactory results have not been obtained because the temperature-dependent thermophysical properties of brake disk materials are not sufficiently known. In this study, the thermophysical properties (thermal diffusivity, the specific heat, and the coefficient of thermal expansion) of three kinds of iron alloy series brake disk materials, FC250, FC170, and FCD50, and two kinds of aluminum alloy series brake disk materials, Al MMC and A356, were measured in the temperature range from room temperature to 500 °C, and the thermal conductivity was calculated using the measured thermal diffusivity, specific heat capacity, and density. As expected, the results show that the two series have significant differences in respect of the thermophysical properties, and to reduce the thermal deformation of the brake disk, the aluminum alloys with a high thermal conductivity and the iron alloys with low thermal expansion are recommended.

  11. Filter properties of seam material from paved urban soils

    Directory of Open Access Journals (Sweden)

    T. Nehls

    2007-08-01

    Full Text Available We studied pavement seam material. This is the soil substrate in joints of pervious pavements in urban areas. It is mostly 1 cm thick and develops from the original seam filling by depositions of all kinds of urban residues, including anthropogenic organic substances. It was investigated, how this unique form of organic matter influences the filter properties of seam material and how the seam material influences heavy metal transport through the pavement. The seam material is characterised by a darker munsell colour, higher organic carbon content, higher surface areas, higher cation exchange capacities, but a lower fraction of high adsorption energy sites compared to the original seam filling. The deposited anthropogenic organic matter itself could be characterised as particulate and non-polar. Compared to natural soils, it has a small surface area and a low surface charge density resulting in a small cation exchange capacity of only 75 cmol(+ kg−1C. The seam material shows stronger sorption of Pb and Cd compared to the original construction sand. The retardation capacity of seam material towards Pb is similar, towards Cd it is much smaller compared to natural soils. The simulated long term displacement scenarios for a street in Berlin do not indicate an acute contamination risk for Pb. For Cd the infiltration from ponds can lead to a displacement of Cd during only one decade.

  12. Material Properties of Wire for the Fabrication of Knotted Fences

    Directory of Open Access Journals (Sweden)

    Dirk J. Pons

    2014-01-01

    Full Text Available This paper describes the materials properties of galvanised fencing wire, as used in the fabrication of knotted wire fences. A range of physical properties are investigated: tensile strength, ductility in tension, Young’s modulus, three-point bending, and bending span. A range of commercially available wire products were tested. The results show that most, but not all, high tensile wire samples met the minimum tensile and ductility requirements. Young’s modulus results failed to provide any meaningful insights into wire quality. Flexural modulus results also failed to provide any insight into wire quality issues, with no statistically significant differences existing between acceptable and problematic wire batches. The implications are that premature fence failures are unlikely to be caused solely by reduced tensile properties. Existing test methods, including tensile strength and ductility, are somewhat incomplete, perhaps even unreliable, as measures of wire quality.

  13. Regional material properties of the human hip joint capsule ligaments.

    Science.gov (United States)

    Hewitt, J; Guilak, F; Glisson, R; Vail, T P

    2001-05-01

    The hip joint capsule functions to constrain translation between the femur and acetabulum while allowing rotational and planar movements. Despite the crucial role it plays in the pathogenesis of hip instability, little is known about its biomechanical properties. The goal of this study was to determine the regional material properties of the iliofemoral and ischiofemoral ligaments of the capsule. Ten human cadaveric specimens of each ligament were tested to failure in tension. The stress at failure, strain at failure, strain energy density at failure, toe- and linear-region elastic moduli, and the Poisson's ratio were measured for each ligament. The strain to failure was greatest in the ischiofemoral ligament, while no significant difference was noted in failure stress by region or ligament. The Young's moduli of elasticity ranged from 76.1 to 285.8 MPa among the different ligaments, and were generally consistent with properties previously reported for the shoulder capsule. The elastic moduli and strain energy density at failure differed by region. No significant differences in Poisson's ratio were found by region or ligament. The average Poisson's ratio was approximately 1.4, consistent with anisotropic behavior of ligamentous tissues. Understanding the material properties of the hip capsule may help the orthopaedic surgeon better understand normal ligament function, and thereby choose a surgical approach or strategy of repair. Furthermore, knowledge of the normal mechanical function of the hip capsule ligaments could assist in the evaluation of the success of a repair.

  14. Space-Time Transfinite Interpolation of Volumetric Material Properties.

    Science.gov (United States)

    Sanchez, Mathieu; Fryazinov, Oleg; Adzhiev, Valery; Comninos, Peter; Pasko, Alexander

    2015-02-01

    The paper presents a novel technique based on extension of a general mathematical method of transfinite interpolation to solve an actual problem in the context of a heterogeneous volume modelling area. It deals with time-dependent changes to the volumetric material properties (material density, colour, and others) as a transformation of the volumetric material distributions in space-time accompanying geometric shape transformations such as metamorphosis. The main idea is to represent the geometry of both objects by scalar fields with distance properties, to establish in a higher-dimensional space a time gap during which the geometric transformation takes place, and to use these scalar fields to apply the new space-time transfinite interpolation to volumetric material attributes within this time gap. The proposed solution is analytical in its nature, does not require heavy numerical computations and can be used in real-time applications. Applications of this technique also include texturing and displacement mapping of time-variant surfaces, and parametric design of volumetric microstructures.

  15. Static Magnetic Properties of AL800 Garnet Material

    Energy Technology Data Exchange (ETDEWEB)

    Kuharik, J. [Fermilab; Madrak, R. [Fermilab; Makarov, A. [Fermilab; Pellico, W. [Fermilab; Sun, S. [Fermilab; Tan, C. Y. [Fermilab; Terechkine, I. [Fermilab

    2017-05-17

    A second harmonic tunable RF cavity is being devel-oped for the Fermilab Booster. This device, which prom-ises reduction of the particle beam loss at the injection, transition, and extraction stages, employs perpendicularly biased garnet material for frequency tuning. The required range of the tuning is significantly wider than in previously built and tested tunable RF devices. As a result, the mag-netic field in the garnet comes fairly close to the gyromag-netic resonance line at the lower end of the frequency range. The chosen design concept of a tuner for the cavity cannot ensure uniform magnetic field in the garnet mate-rial; thus, it is important to know the static magnetic prop-erties of the material to avoid significant increase in the lo-cal RF loss power density. This report summarizes studies performed at Fermilab to understand variations in the mag-netic properties of the AL800 garnet material used to build the tuner of the cavity.

  16. Preparation and properties on hollow nano-structured smoke material

    Science.gov (United States)

    Liu, Xiang-cui; Dai, Meng-yan; Fang, Guo-feng; Shi, Wei-dong; Cheng, Xiang; Liu, Hai-feng; Zhang, Tong

    2013-09-01

    In recent years, the weapon systems of laser guidance and infrared (IR) imaging guidance have been widely used in modern warfare because of their high precision and strong anti-interference. Notwithstanding, military smoke, as a rapid and effective passive jamming means, can effectively counteract the attack of enemy precision-guided weapons by scattering and absorbability. Conventional smoke has good attenuation capability only to visible light (0.4-0.76 μm), but hardly any effect to other electromagnetic wave band. The weapon systems of laser guidance and IR imaging guidance usually work in broad band, including near IR (1-3 μm), middle IR (3-5 μm), far IR (8-14 μm), and so on. Accordingly, exploiting and using new efficient obscurant materials, which is one of the important factors that develop smoke technology, have become a focus and attracted more interests around the world. Then nano-structured materials that are developing very quickly have turned into our new choice. Hollow nano-structured materials (HNSM) have many special properties because of their nano-size wall-thickness and sub-micron grain-size. After a lot of HNSM were synthesized in this paper, their physical and chemical properties, including grain size, phase composition, microstructure, optical properties and resistivity were tested and analysed. Then the experimental results of the optical properties showed that HNSM exhibit excellent wave-absorbing ability in ultraviolet, visible and infrared regions. On the basis of the physicochemmical properties, HNSM are firstly applied in smoke technology field. And the obscuration performance of HNSM smoke was tested in smoke chamber. The testing waveband included 1.06μm and 10.6μm laser, 3-5μm and 8-14μm IR radiation. Then the main parameters were obtained, including the attenuation rate, the transmission rate, the mass extinction coefficient, the efficiency obscuring time, and the sedimentation rate, etc. The main parameters of HNSM smoke were

  17. Dynamic properties of the posterior cricoarytenoid muscle.

    Science.gov (United States)

    Cooper, D S; Shindo, M; Sinha, U; Hast, M H; Rice, D H

    1994-12-01

    The aim of this research was to investigate the contractile properties of the posterior cricoarytenoid (PCA) muscle. Simultaneous measurements were made of the isometric force, temperature, and electromyographic activity of the dorsal cricoarytenoid muscle of anesthetized dogs during supramaximal stimulation of the recurrent laryngeal nerve for twitch and tetanic contraction. The conduction delay between stimulation of the recurrent nerve at the level of the larynx and the onset of the muscle action potential averaged 2.0 +/- 0.2 milliseconds (ms), and the latent period between the onset of electrical activity of the muscle and the onset of contraction had a mean duration of 3.3 +/- 0.8 ms. The mean of isometric contraction times found was 33.3 +/- 2.0 ms, shorter than most previous studies of canine PCA muscle. Tetanic frequency defined as smooth contraction was higher than previous estimates. Considerations of scaling of physiological time based on animal mass were applied to analysis of the experimental findings to make possible systematic comparison of previous findings across species and animal size.

  18. Structural, Dynamic, and Vibrational Properties during Heat Transfer in Si/Ge Superlattices: A Car-Parrinello Molecular Dynamics Study

    CERN Document Server

    Ji, Pengfei; Yang, Mo

    2016-01-01

    The structural, dynamic, and vibrational properties during the heat transfer process in Si/Ge superlattices, are studied by analyzing the trajectories generated by the ab initio Car-Parrinello molecular dynamics simulation. The radial distribution functions and mean square displacements are calculated and further discussions are made to explain and probe the structural changes relating to the heat transfer phenomenon. Furthermore, the vibrational density of states of the two layers (Si/Ge) are computed and plotted to analyze the contributions of phonons with different frequencies to the heat conduction. Coherent heat conduction of the low frequency phonons is found and their contributions to facilitate heat transfer are confirmed. The Car-Parrinello molecular dynamics simulation outputs in the work show reasonable thermophysical results of the thermal energy transport process and shed light on the potential applications of treating the heat transfer in the superlattices of semiconductor materials from a quant...

  19. Material dynamics under extreme conditions of pressure and strain rate

    Energy Technology Data Exchange (ETDEWEB)

    Remington, B A; Allen, P; Bringa, E; Hawreliak, J; Ho, D; Lorenz, K T; Lorenzana, H; Meyers, M A; Pollaine, S W; Rosolankova, K; Sadik, B; Schneider, M S; Swift, D; Wark, J; Yaakobi, B

    2005-09-06

    Solid state experiments at extreme pressures (10-100 GPa) and strain rates ({approx}10{sup 6}-10{sup 8}s{sup -1}) are being developed on high-energy laser facilities, and offer the possibility for exploring new regimes of materials science. These extreme solid-state conditions can be accessed with either shock loading or with a quasi-isentropic ramped pressure drive. Velocity interferometer measurements establish the high pressure conditions. Constitutive models for solid-state strength under these conditions are tested by comparing 2D continuum simulations with experiments measuring perturbation growth due to the Rayleigh-Taylor instability in solid-state samples. Lattice compression, phase, and temperature are deduced from extended x-ray absorption fine structure (EXAFS) measurements, from which the shock-induced {alpha}-{omega} phase transition in Ti and the {alpha}-{var_epsilon} phase transition in Fe are inferred to occur on sub-nanosec time scales. Time resolved lattice response and phase can also be measured with dynamic x-ray diffraction measurements, where the elastic-plastic (1D-3D) lattice relaxation in shocked Cu is shown to occur promptly (< 1 ns). Subsequent large-scale molecular dynamics (MD) simulations elucidate the microscopic dynamics that underlie the 3D lattice relaxation. Deformation mechanisms are identified by examining the residual microstructure in recovered samples. The slip-twinning threshold in single-crystal Cu shocked along the [001] direction is shown to occur at shock strengths of {approx}20 GPa, whereas the corresponding transition for Cu shocked along the [134] direction occurs at higher shock strengths. This slip-twinning threshold also depends on the stacking fault energy (SFE), being lower for low SFE materials. Designs have been developed for achieving much higher pressures, P > 1000 GPa, in the solid state on the National Ignition Facility (NIF) laser.

  20. Wave dynamics and composite mechanics for microstructured materials and metamaterials

    CERN Document Server

    2017-01-01

    This volume deals with topical problems concerning technology and design in construction of modern metamaterials. The authors construct the models of mechanical, electromechanical and acoustical behavior of the metamaterials, which are founded upon mechanisms existing on micro-level in interaction of elementary structures of the material. The empiric observations on the phenomenological level are used to test the created models. The book provides solutions, based on fundamental methods and models using the theory of wave propagation, nonlinear theories and composite mechanics for media with micro- and nanostructure. They include the models containing arrays of cracks, defects, with presence of micro- and nanosize piezoelectric elements and coupled physical-mechanical fields of different nature. The investigations show that the analytical, numerical and experimental methods permit evaluation of the qualitative and quantitative properties of the materials of this sort, with diagnosis of their effective characte...

  1. Prediction of nonlinear optical properties of organic materials. General theoretical considerations

    Science.gov (United States)

    Cardelino, B.; Moore, C.; Zutaut, S.

    1993-01-01

    The prediction of nonlinear optical properties of organic materials is geared to assist materials scientists in the selection of good candidate molecules. A brief summary of the quantum mechanical methods used for estimating hyperpolarizabilities will be presented. The advantages and limitations of each technique will be discussed. Particular attention will be given to the finite-field method for calculating first and second order hyperpolarizabilities, since this method is better suited for large molecules. Corrections for dynamic fields and bulk effects will be discussed in detail, focusing on solvent effects, conformational isomerization, core effects, dispersion, and hydrogen bonding. Several results will be compared with data obtained from third-harmonic-generation (THG) and dc-induced second harmonic generation (EFISH) measurements. These comparisons will demonstrate the qualitative ability of the method to predict the relative strengths of hyperpolarizabilities of a class of compounds. The future application of molecular mechanics, as well as other techniques, in the study of bulk properties and solid state defects will be addressed. The relationship between large values for nonlinear optical properties and large conjugation lengths is well known, and is particularly important for third-order processes. For this reason, the materials with the largest observed nonresonant third-order properties are conjugated polymers. An example of this type of polymer is polydiacetylene. One of the problems in dealing with polydiacetylene is that substituents which may enhance its nonlinear properties may ultimately prevent it from polymerizing. A model which attempts to predict the likelihood of solid-state polymerization is considered, along with the implications of the assumptions that are used. Calculations of the third-order optical properties and their relationship to first-order properties and energy gaps will be discussed. The relationship between monomeric and

  2. Scanning Probe Evaluation of Electronic, Mechanical and Structural Material Properties

    Science.gov (United States)

    Virwani, Kumar

    2011-03-01

    We present atomic force microscopy (AFM) studies of a range of properties from three different classes of materials: mixed ionic electronic conductors, low-k dielectrics, and polymer-coated magnetic nanoparticles. (1) Mixed ionic electronic conductors are being investigated as novel diodes to drive phase-change memory elements. Their current-voltage characteristics are measured with direct-current and pulsed-mode conductive AFM (C-AFM). The challenges to reliability of the C-AFM method include the electrical integrity of the probe, the sample and the contacts, and the minimization of path capacitance. The role of C-AFM in the optimization of these electro-active materials will be presented. (2) Low dielectric constant (low-k) materials are used in microprocessors as interlayer insulators, a role directly affected by their mechanical performance. The mechanical properties of nanoporous silicate low-k thin films are investigated in a comparative study of nanomechanics measured by AFM and by traditional nanoindentation. Both methods are still undergoing refinement as reliable analytical tools for determining nanomechanical properties. We will focus on AFM, the faster of the two methods, and its developmental challenges of probe shape, cantilever force constant, machine compliance and calibration standards. (3) Magnetic nanoparticles are being explored for their use in patterned media for magnetic storage. Current methods for visualizing the core-shell structure of polymer-coated magnetic nanoparticles include dye-staining the polymer shell to provide contrast in transmission electron microscopy. AFM-based fast force-volume measurements provide direct visualization of the hard metal oxide core within the soft polymer shell based on structural property differences. In particular, the monitoring of adhesion and deformation between the AFM tip and the nanoparticle, particle-by-particle, provides a reliable qualitative tool to visualize core-shell contrast without the use

  3. Evidence on dynamic effects in the water content – water potential relation of building materials

    DEFF Research Database (Denmark)

    Scheffler, Gregor Albrecht; Plagge, Rudolf

    2008-01-01

    the required material functions, i.e. the moisture storage characteristic and the liquid water conductivity, from measured basic properties. The current state of the art in material modelling as well as the corresponding transport theory implies that the moisture transport function is unique...... and that the moisture storage characteristic is process dependent with varying significance for the numerical simulation. On the basis of different building materials, a comprehensive instantaneous profile measurement study has been accomplished. Profiles of water content and relative humidity were obtained during...... a series of adsorption and desorption processes. The data provides clear evidence that the water content – water potential relationship is not only dependent on the process history, but also on the process dynamics. The higher moisture potential gradients were induced, the larger was the deviation between...

  4. Numerical determination of the material properties of porous dust cakes

    CERN Document Server

    Paszun, D

    2008-01-01

    The formation of planetesimals requires the growth of dust particles through collisions. Micron-sized particles must grow by many orders of magnitude in mass. In order to understand and model the processes during this growth, the mechanical properties, and the interaction cross sections of aggregates with surrounding gas must be well understood. Recent advances in experimental (laboratory) studies now provide the background for pushing numerical aggregate models onto a new level. We present the calibration of a previously tested model of aggregate dynamics. We use plastic deformation of surface asperities as the physical model to bring critical velocities for sticking into accordance with experimental results. The modified code is then used to compute compression strength and the velocity of sound in the aggregate at different densities. We compare these predictions with experimental results and conclude that the new code is capable of studying the properties of small aggregates.

  5. Meshless Local Petrov-Galerkin Method for Shallow Shells with Functionally Graded and Orthotropic Material Properties

    Science.gov (United States)

    Sladek, J.; Sladek, V.; Zhang, Ch.

    2008-02-01

    A meshless local Petrov-Galerkin (MLPG) formulation is presented for analysis of shear deformable shallow shells with orthotropic material properties and continuously varying material properties through the shell thickness. Shear deformation of shells described by the Reissner theory is considered. Analyses of shells under static and dynamic loads are given here. For transient elastodynamic case the Laplace-transform is used to eliminate the time dependence of the field variables. A weak formulation with a unit test function transforms the set of the governing equations into local integral equations on local subdomains in the plane domain of the shell. The meshless approximation based on the Moving Least-Squares (MLS) method is employed for the implementation.

  6. CRACK PROPAGATING IN FUNCTIONALLY GRADED COATING WITH ARBITRARILY DISTRIBUTED MATERIAL PROPERTIES BONDED TO HOMOGENEOUS SUBSTRATE

    Institute of Scientific and Technical Information of China (English)

    Zhanqi Cheng; Danying Gao; Zheng Zhong

    2010-01-01

    In this paper,a finite crack with constant length(Yoffe type crack)propagating in a functionally graded coating with spatially varying elastic properties bonded to a homoge-neous substrate of finite thickness under anti-plane loading was studied.A multi-layered model is employed to model arbitrary variations of material properties based on two linearly-distributed material compliance parameters.The mixed boundary problem is reduced to a system of singular integral equations that are solved numerically.Some numerical examples are given to demonstrate the accuracy,efficiency and versatility of the model.The numerical results show that the graded parameters,the thicknesses of the interracial layer and the two homogeneous layers,the crack size and speed have significant effects on the dynamic fracture behavior.

  7. Synthesis, processing and properties of materials for SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Bates, J.L.; Armstrong, T.A.; Kingsley, J.J.; Pederson, L.R.

    1994-03-01

    The synthesis and processing methods of complex oxide materials can significantly influence use in solid oxide fuel cells (SOFCs). This paper discusses (1) effects of powder synthesis and conditioning on fabrication, i.e., sintering, where close, reproducible control of composition and structure are required, and (2) influences on electrical, mechanical, structural and electrochemical properties that can influence SOFC performance. Examples are given for chromites, manganites and related oxides used as interconnections and electrodes in SOFCs. Materials, from source to incorporation into the fuel cell and generator, is a major issue in the development of solid oxide fuel cells (SOFCs). An integral part of this is the synthesis from chemicals and other virgin materials, generally as an oxide or metal powder, which can become a SOFC component. In some instances, such as with electrochemical vapor deposition, the component is formed directly from the chemicals. The synthesized materials are then conditioned and processes prior to fabrication into the fuel cell component, either separately or in conjunction with other material components.

  8. Slow dynamics of supercooled water confined in nanoporous silica materials

    Energy Technology Data Exchange (ETDEWEB)

    Liu, L [Department of Nuclear Engineering, 24-209 MIT, Cambridge, MA 02139 (United States); Faraone, A [Department of Nuclear Engineering, 24-209 MIT, Cambridge, MA 02139 (United States); Mou, C-Y [Department of Chemistry, National Taiwan University, Taipei, 106, Taiwan (China); Yen, C-W [Department of Chemistry, National Taiwan University, Taipei, 106, Taiwan (China); Chen, S-H [Department of Nuclear Engineering, 24-209 MIT, Cambridge, MA 02139 (United States)

    2004-11-17

    We review our incoherent quasielastic neutron scattering (QENS) studies of the dynamics of supercooled water confined in nanoporous silica materials. QENS data were analysed by using the relaxing cage model (RCM) previously developed by us. We first use molecular dynamics (MD) simulation of the extended simple point charge model (SPC/E) for bulk supercooled water to establish the validity of the RCM, which applies to both the translational and rotational motion of water molecules. We then assume that the dynamics of water molecules in the vicinity of a hydrophilic surface is similar to a bulk water at an equivalent lower supercooled temperature. This analogy was experimentally demonstrated in previous investigations of water in Vycor glasses and near hydrophilic protein surfaces. Studies were made of supercooled water in MCM-41-S (pore sizes 25, 18, and 14 A) and MCM-48-S (pore size 22 A) using three QENS spectrometers of respective energy resolutions 1, 30, and 60 {mu}eV, covering the temperature range from 325 to 200 K. Five quantities are extracted from the analysis: they are {beta}, the stretch exponent characterizing the {alpha}-relaxation; {beta}{gamma}, the exponent determining the power-law dependence of the relaxation time on Q; <{tau}{sub 0}>, the Q-independent pre-factor for the average translational relaxation time; <{tau}{sub R{sub 1}}>, the relaxation time for the first-order rotational correlation function; and <{tau}{sub R{sub 3}}>, the relaxation time for the second-order rotational correlation function. We discuss the temperature dependence of these parameters and note that, in particular, the dynamics is rapidly slowing down at temperature around 220 K, signalling the onset of a structural arrest transition of liquid water into an amorphous solid water.

  9. Dynamic Control of Radiative Heat Transfer with Tunable Materials for Thermal Management in Both Far and Near Fields

    Science.gov (United States)

    Yang, Yue

    The proposed research mainly focuses on employing tunable materials to achieve dynamic control of radiative heat transfer in both far and near fields for thermal management. Vanadium dioxide (VO2), which undergoes a phase transition from insulator to metal at the temperature of 341 K, is one tunable material being applied. The other one is graphene, whose optical properties can be tuned by chemical potential through external bias or chemical doping. (Abstract shortened by ProQuest.).

  10. Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties

    Directory of Open Access Journals (Sweden)

    Almudena Díaz-García

    2017-01-01

    Full Text Available Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

  11. Theory of static and dynamic properties of Gd

    DEFF Research Database (Denmark)

    Lindgård, Per-Anker

    1986-01-01

    Gadolinium is a Heisenberg magnet intermediate between the localized EuO and the itinerant Fe and Ni. The authors develop a correlation theory for Gd and calculate self-consistently both static and dynamic properties. One finds that the high frequency spin waves persist for T>Tc. The static...

  12. Dynamic solar radiation control in buildings by applying electrochromic materials

    Energy Technology Data Exchange (ETDEWEB)

    Jelle, B.P.; Gustavsen, A.

    2010-07-01

    Full text: Smart windows like electrochromic windows (ECWs) are windows which are able to regulate the solar radiation throughput by application of an external voltage. The ECWs may decrease heating, cooling and electricity loads in buildings by admitting the optimum level of solar energy and daylight into the buildings at any given time, e.g. cold winter climate versus warm summer climate demands. In order to achieve as dynamic and flexible solar radiation control as possible, the ECWs may be characterized by a number of solar radiation glazing factors, i.e. ultraviolet solar transmittance, visible solar transmittance, solar transmittance, solar material protection factor, solar skin protection factor, external visible solar reflectance, internal visible solar reflectance, solar reflectance, solar absorbance, emissivity, solar factor and colour rendering factor. Comparison of these solar quantities for various electrochromic material and window combinations and configurations enables one to select the most appropriate electrochromic materials and ECWs for specific buildings. Measurements and calculations were carried out on two different electrochromic window devices. (Author)

  13. Determination of dynamic fracture initiation toughness of linear elastic materials; Obtencion de la tenacidad de fractura dinamica de iniciacion de materiales elasticos y lineales

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez-Saez, J.; Rubio, L.; Luna de, S.; Perez-Castellanos, J. L.; Navarro, C. [Universidad Carlos III. Madrid (Spain)

    2001-07-01

    The need to guarantee the structural integrity of key mechanical and structural components require the use of the damage tolerant concepts in their design, and the fracture properties of the material must be known in actual operations conditions. The behaviour of components subjected to dynamic loads is very different from that under static loads: the existence of inertial forces and the strain rate may affect the properties of the material. This works aims to present the experimental techniques most commonly used to determine the dynamic fracture properties of linear elastic materials, as well as the analytical and numerical tools used to interpret the experiments. (Author) 89 refs.

  14. Material properties of bovine intervertebral discs across strain rates.

    Science.gov (United States)

    Newell, Nicolas; Grigoriadis, Grigorios; Christou, Alexandros; Carpanen, Diagarajen; Masouros, Spyros D

    2017-01-01

    The intervertebral disc (IVD) is a complex structure responsible for distributing compressive loading to adjacent vertebrae and allowing the vertebral column to bend and twist. To study the mechanical behaviour of individual components of the IVD, it is common for specimens to be dissected away from their surrounding tissues for mechanical testing. However, disrupting the continuity of the IVD to obtain material properties of each component separately may result in erroneous values. In this study, an inverse finite element (FE) modelling optimisation algorithm has been used to obtain material properties of the IVD across strain rates, therefore bypassing the need to harvest individual samples of each component. Uniaxial compression was applied to ten fresh-frozen bovine intervertebral discs at strain rates of 10(-3)-1/s. The experimental data were fed into the inverse FE optimisation algorithm and each experiment was simulated using the subject specific FE model of the respective specimen. A sensitivity analysis revealed that the IVD's response was most dependent upon the Young's modulus (YM) of the fibre bundles and therefore this was chosen to be the parameter to optimise. Based on the obtained YM values for each test corresponding to a different strain rate (ε̇), the following relationship was derived:YM=35.5lnε̇+527.5. These properties can be used in finite element models of the IVD that aim to simulate spinal biomechanics across loading rates. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  15. Tooth and bone deformation: structure and material properties by ESPI

    Science.gov (United States)

    Zaslansky, Paul; Shahar, Ron; Barak, Meir M.; Friesem, Asher A.; Weiner, Steve

    2006-08-01

    In order to understand complex-hierarchical biomaterials such as bones and teeth, it is necessary to relate their structure and mechanical-properties. We have adapted electronic speckle pattern-correlation interferometry (ESPI) to make measurements of deformation of small water-immersed specimens of teeth and bones. By combining full-field ESPI with precision mechanical loading we mapped sub-micron displacements and determined material-properties of the samples. By gradually and elastically compressing the samples, we compensate for poor S/N-ratios and displacement differences of about 100nm were reliably determined along samples just 2~3mm long. We produced stress-strain curves well within the elastic performance range of these materials under biologically relevant conditions. For human tooth-dentin, Young's modulus in inter-dental areas of the root is 40% higher than on the outer sides. For cubic equine bone samples the compression modulus of axial orientations is about double the modulus of radial and tangential orientations (20 GPa versus 10 GPa respectively). Furthermore, we measured and reproduced a surprisingly low Poisson's ratio, which averaged about 0.1. Thus the non-contact and non-destructive measurements by ESPI produce high sensitivity analyses of mechanical properties of mineralized tissues. This paves the way for mapping deformation-differences of various regions of bones, teeth and other biomaterials.

  16. Materials Selection, Synthesis, and Dielectrical Properties of PVC Nanocomposites

    Directory of Open Access Journals (Sweden)

    Youssef Mobarak

    2013-01-01

    Full Text Available Materials selection process for electrical insulation application was carried out using Cambridge Engineering Selector (CES program. Melt mixing technique was applied to prepare polyvinyl-chloride- (PVC- nanofumed silica and nanomontmorillonite clay composites. Surface analysis and particles dispersibility were examined using scanning electron microscope. Dielectrical properties were assessed using Hipot tester. An experimental work for dielectric loss of the nanocomposite materials has been investigated in a frequency range of 10 Hz–50 kHz. The initial results using CES program showed that microparticles of silica and clay can improve electrical insulation properties and modulus of elasticity of PVC. Nano-montmorillonite clay composites were synthesized and characterized. Experimental analyses displayed that trapping properties of matrix are highly modified by the presence of nanofillers. The nanofumed silica and nanoclay particles were dispersed homogenously in PVC up to 10% wt/wt. Dielectric loss tangent constant of PVC-nanoclay composites was decreased successfully from 0.57 to 0.5 at 100 Hz using fillers loading from 1% to 10% wt/wt, respectively. Nano-fumed silica showed a significant influence on the electrical resistivity of PVC by enhancing it up to 1 × 1011 Ohm·m.

  17. Dynamic test devices for analyzing the tensile properties of concrete

    NARCIS (Netherlands)

    Forquin, P.; Riedel, W.; Weerheijm, J.

    2013-01-01

    Owing to their low tensile failure strain, concrete is a difficult material to test under dynamic tensile loading. Indeed, conventional testing apparatuses such as high-speed hydraulic presses or Split Hopkinson Bar facilities rely on a mechanical balance of the specimen implying a short round-trip

  18. Oxide Thermoelectric Materials: A Structure-Property Relationship

    Science.gov (United States)

    Nag, Abanti; Shubha, V.

    2014-04-01

    Recent demand for thermoelectric materials for power harvesting from automobile and industrial waste heat requires oxide materials because of their potential advantages over intermetallic alloys in terms of chemical and thermal stability at high temperatures. Achievement of thermoelectric figure of merit equivalent to unity ( ZT ≈ 1) for transition-metal oxides necessitates a second look at the fundamental theory on the basis of the structure-property relationship giving rise to electron correlation accompanied by spin fluctuation. Promising transition-metal oxides based on wide-bandgap semiconductors, perovskite and layered oxides have been studied as potential candidate n- and p-type materials. This paper reviews the correlation between the crystal structure and thermoelectric properties of transition-metal oxides. The crystal-site-dependent electronic configuration and spin degeneracy to control the thermopower and electron-phonon interaction leading to polaron hopping to control electrical conductivity is discussed. Crystal structure tailoring leading to phonon scattering at interfaces and nanograin domains to achieve low thermal conductivity is also highlighted.

  19. The Study of the Thermoelectric Properties of Phase Change Materials

    Science.gov (United States)

    Yin, Ming; Abdi, Mohammed; Noimande, Zibusisu; Mbamalu, Godwin; Alameeri, Dheyaa; Datta, Timir

    We study thermoelectric property that is electrical phenomena occurring in conjunction with the flow of heat of phase-change materials (PCM) in particular GeSbTe (GST225). From given sets of material parameters, COMSOL Multiphysics heat-transfer module is used to compute maps of temperature and voltage distribution in the PCM samples. These results are used to design an apparatus including the variable temperature sample holder set up. An Arbitrary/ Function generator and a circuit setup is also designed to control the alternation of heaters embedded on the sample holder in order to ensure sequential back and forward flow of heat current from both sides of the sample. Accurate values of potential differences and temperature distribution profiles are obtained in order to compute the Seebeck coefficient of the sample. The results of elemental analysis and imaging studies such as XRD, UV-VIS, EDEX and SEM of the sample are obtained. Factors affecting the thermoelectric properties of phase change memory are also discussed. NNSA/ DOD Consortium for Materials and Energy Studies.

  20. Size and Geometry Effects on the Mechanical Properties of Carrara Marble Under Dynamic Loadings

    Science.gov (United States)

    Zou, Chunjiang; Wong, Louis Ngai Yuen

    2016-05-01

    The effects of specimen size and geometry on the dynamic mechanical properties of Carrara marble including compressive strength, failure strain and elastic modulus are investigated in this research. Four different groups of specimens of different sizes and cross-sectional geometries are loaded under a wide range of strain rates by the split Hopkinson pressure bar setup. The experimental results indicate that all these mechanical properties are significantly influenced by the specimen size and geometry to different extent, hence highlighting the importance of taking into account of the specimen size and geometry in dynamic tests on rock materials. In addition, the transmission coefficient and the determination of strain rate under dynamic tests are discussed in detail.

  1. Structure-property relationships of curved aromatic materials from first principles.

    Science.gov (United States)

    Zoppi, Laura; Martin-Samos, Layla; Baldridge, Kim K

    2014-11-18

    character through functionalization. This Account offers discussion of current state-of-the-art electronic structure approaches for prediction of structural, electronic, optical, and transport properties of materials, with illustration of these capabilities from a series of investigations involving curved aromatic materials. The class of curved aromatic materials offers the ability to investigate methodology across a wide range of materials complexity, including (a) molecules, (b) molecular crystals, (c) molecular adsorbates on metal surfaces, and (d) molecular nanojunctions. A reliable pallet of theoretical tools for such a wide array relies on expertise spanning multiple fields. Working together with experimental experts, advancements in the fundamental understanding of structural and dynamical properties are enabling focused design of functional materials. Most importantly, these studies provide an opportunity to compare experimental and theoretical capabilities and open the way for continual improvement of these capabilities.

  2. Determination Of Thermal And Mechanical Properties Of Packaging Materials For The Use In FEM-Simulations

    Science.gov (United States)

    Roellig, Mike; Boehme, Bjoern; Meier, Karsten; Metasch, René

    2011-09-01

    Conventional and future electronic packages merge several different materials. Polymers, metals, solders, dielectrics, glasses, silicon, composites come together and show strong mechanical and material interaction. These interfacial effects increase if the miniaturization and diversification keep on rising as it is proposed. Many efforts have to be done to assure the system reliability of new electronic packages. The Finite Element Simulation has the ability to support the development process of new packages. The application of the FEM-analysis requires the knowledge about the precise mechanical and thermal behaviour of the materials. The paper presents different measurement methods to determine accurate mechanical material properties of moulding compound polymers, underfillers, solder mask, and wafer photo resist and solder joints. The temperature dependency is essential to be respected. The polymer materials moulding compound as well as solder mask were characterized by Dynamic Mechanical Analysis under humidity influences to determine mechanical properties as function of moisture and temperature. Further experiments on polymer were conducted to extract the cure kinetics by Differential Scanning Calorimetry and to determine Bulk Modulus by Pressure-Volume-Temperature experiments (PVT). Altogether, these material properties need to be modeled in a comprehensive way fitting to each other. The common practice of just compiling data from different sources has been found to fail yielding in reliable and accurate results. The conditions under which the data were determined may cause mismatches between them and cause inconsistencies within the model. If a convergent solution was obtained at all, much simulation time would be needed as many iterations with small time steps were needed. In order to avoid this, the paper reports an approach of characterizing the temperature and time dependent mechanical material properties in one comprehensive scheme. The solder

  3. EFFECTS OF PHENOL RESIN ADDITIVE ON DYNAMIC MECHANICAL PROPERTIES OF ACRYLATE RUBBER AND ITS BLENDS

    Institute of Scientific and Technical Information of China (English)

    Chi-fei Wu

    2003-01-01

    The dynamic mechanical properties of a new blend system consisting of phenol resin and polar polymer (acrylate rubber and/or chlorinated polypropylene) were investigated. It was found that the addition of phenol resin to acrylate rubber and its incompatible blend can cause a remarkable improvement in the temperature dependence of the loss tangent. As a result, the present blends are very good damping materials.

  4. Investigation of nonlinear dynamic soil property at the Savannah River Site

    Energy Technology Data Exchange (ETDEWEB)

    Lee, R.C.

    2000-01-17

    This document summarizes laboratory dynamic soil testing investigations conducted by the University of Texas at Austin (UTA) for the Savannah River Site (SRS) (Stokoe et al., 1995a, Stokoe et al., 1995b, Sponseller and Stokoe, 1995). The purpose of the investigation is to provide an evaluation of past testing results in the context of new test data and the development of consistent site wide models of material strain dependencies based upon geologic formation, depth, and relevant index properties.

  5. Real-time measurement of materials properties at high temperatures by laser produced plasmas

    Science.gov (United States)

    Kim, Yong W.

    1990-01-01

    Determination of elemental composition and thermophysical properties of materials at high temperatures, as visualized in the context of containerless materials processing in a microgravity environment, presents a variety of unusual requirements owing to the thermal hazards and interferences from electromagnetic control fields. In addition, such information is intended for process control applications and thus the measurements must be real time in nature. A new technique is described which was developed for real time, in-situ determination of the elemental composition of molten metallic alloys such as specialty steel. The technique is based on time-resolved spectroscopy of a laser produced plasma (LPP) plume resulting from the interaction of a giant laser pulse with a material target. The sensitivity and precision were demonstrated to be comparable to, or better than, the conventional methods of analysis which are applicable only to post-mortem specimens sampled from a molten metal pool. The LPP technique can be applied widely to other materials composition analysis applications. The LPP technique is extremely information rich and therefore provides opportunities for extracting other physical properties in addition to the materials composition. The case in point is that it is possible to determine thermophysical properties of the target materials at high temperatures by monitoring generation and transport of acoustic pulses as well as a number of other fluid-dynamic processes triggered by the LPP event. By manipulation of the scaling properties of the laser-matter interaction, many different kinds of flow events, ranging from shock waves to surface waves to flow induced instabilities, can be generated in a controllable manner. Time-resolved detection of these events can lead to such thermophysical quantities as volume and shear viscosities, thermal conductivity, specific heat, mass density, and others.

  6. A time-resolved infrared vibrational spectroscopic study of the photo-dynamics of crystalline materials.

    Science.gov (United States)

    Towrie, Mike; Parker, Anthony W; Ronayne, Kate L; Bowes, Katharine F; Cole, Jacqueline M; Raithby, Paul R; Warren, John E

    2009-01-01

    Time-resolved infrared vibrational spectroscopy is a structurally sensitive probe of the excited-state properties of matter. The technique has found many applications in the study of molecules in dilute solution phase but has rarely been applied to crystalline samples. We report on the use of a sensitive pump-probe time-resolved infrared spectrometer and sample handling techniques for studies of the ultrafast excited-state dynamics of crystalline materials. The charge transfer excited states of crystalline metal carbonyls and the proton transfer of dihydroxyquinones are presented and compared with the solution phase.

  7. Emergent Properties in Natural and Artificial Dynamical Systems

    CERN Document Server

    Aziz-Alaoui, M.A

    2006-01-01

    An important part of the science of complexity is the study of emergent properties arising through dynamical processes in various types of natural and artificial systems. This is the aim of this book, which is the outcome of a discussion meeting within the first European conference on complex systems. It presents multidisciplinary approaches for getting representations of complex systems and using different methods to extract emergent structures. This carefully edited book studies emergent features such as self organization, synchronization, opening on stability and robustness properties. Invariant techniques are presented which can express global emergent properties in dynamical and in temporal evolution systems. This book demonstrates how artificial systems such as a distributed platform can be used for simulation used to search emergent placement during simulation execution.

  8. Acoustic Properties of Innovative Material from Date Palm Fibre

    Directory of Open Access Journals (Sweden)

    Lamyaa Abd AL-Rahman

    2012-01-01

    Full Text Available Problem statement: An organic material is one of the major requirements to improve living environment and the invention of materials need to consider for the best solution. This study presents an experimental investigation on pure porous from Date Palm Fibre (DPF. The effectiveness of sound absorbers depends on structural architecture of this material. This study was conducted to examine the potential of using date palm fibre as sound absorber. The effects of porous layer thicknesses, densities and compression on Acoustic Absorption Coefficient (AAC of sound absorber using date palm fibre were studied. Approach: Rigid frame Johnson-Allard Model for various sample thicknesses was used in this study. The measurements were conducted in impedance tube on normal incidence acoustic absorption. The date palm fibre was mixed with latex which used for physical treatment on this material. Acoustic absorption behaviour of a porous material with different thicknesses was studied as well as samples with same thickness but different densities. In addition, samples with same properties but different period of compression time were inspected. The tests were in accordance to ISO 10534-2 and ASTM E1050-98 international standards for Acoustic Absorption Coefficient (AAC. Results: The experimental data indicates that two peak values of AAC is 0.93 at 1356Hz for sample with 50 mm thickness, also the AAC at high frequency for same thickness is 0.99 at 4200-4353 Hz that means able to improve acoustic absorption coefficient at low and high frequencies with significant increasing. Meanwhile, another experimental results were acquired for AAC of date palm fibre, with samples thicknesses of 35 mm at different densities .The results show that denser sample (11 Kg m-3 has higher AAC value of 0.83 at 1934- 2250 Hz as compared to less dense sample (9.92 Kg m-3 with AAC value 0.84 at 2443-2587 Hz . Conclusion: Acoustic absorption coefficient AAC of date palm fibre was

  9. Saturation properties of a supercritical gas sorbed in nanoporous materials.

    Science.gov (United States)

    Poirier, Eric; Dailly, Anne

    2012-12-28

    The description of experimental gas adsorption data in terms of an accurate model is key to understand the adsorption mechanism and its limits. As a basic feature such a model should predict correctly the conditions under which saturation occurs. However, in the absence of bulk condensation properties for a supercritical adsorbate this matter remains open to discussions. In this study, the decreasing region of excess hydrogen adsorption isotherms measured down to 50 K is used to determine the adsorbed phase volume, density and pressure corresponding to saturation. The experimental method developed for these key measurements addresses the challenges of very low temperature adsorption measurements at high pressure. Therefore, the modifications specially made to a cryostat used in conjunction with a Sievert apparatus to reach high temperature stability (±10 mK) down to 40 K are presented. The approach is implemented on the novel nanoporous materials UMCM-1 and NOTT-112 over 50-77 K and 0-40 bar. The derived hydrogen saturation properties are found to be consistent with a Dubinin-Astakhov model. Importantly, the measured adsorbed hydrogen phase volume also compares well with the pore volume obtained from Ar porosimetry. The found saturation properties provide a physical basis to calculate consistent absolute adsorption isotherms and enthalpies, and to project the ultimate adsorption capacity of a conceptual material with a maximized specific surface area. The present findings provide additional evidence that the common view on supercritical adsorption, in which it is assumed that no liquid is formed and that the only possible mechanism involves monolayer coverage, does not hold in many nanoporous materials.

  10. A plasmonic fluid with dynamically tunable optical properties

    KAUST Repository

    Bhattacharjee, Rama Ranjan

    2009-01-01

    We report the first synthesis of a gold nanorod (GNR)-based nanocomposite that exhibits solid-like plasmonic properties while behaving in a liquid-like manner. Tuning the degree of GNR clustering controls the material\\'s responsiveness to external stimuli, such as mechanical shearing, due to the sensitivity of the localized surface plasmon resonance to interparticle interactions. © 2009 The Royal Society of Chemistry.

  11. Magnetomechanical Properties Of Composite Materials With Giant Magnetostriction

    Directory of Open Access Journals (Sweden)

    Tomiczek A.E.

    2015-09-01

    Full Text Available The aim of this work was to observe the changes in the magnetomechanical properties of composite materials with different Tb0.3Dy0.7Fe1.9 (Terfenol-D powder particle-size distributions and varying volume fractions in the polyurethane matrix. The results show a direct relationship between the properties and the particle size of the Tb0.3Dy0.7Fe1.9 powder: the increases in the particle-size distribution of the Tb0.3Dy0.7Fe1.9 powder in the matrix amplify the magnetostrictive responses and the compressive modulus values. Moreover, it was found that the key role in efficiency of the transformation of magnetic energy into mechanical plays the initial compressing pre-stress.

  12. Research on lunar materials. [optical, chemical, and electrical properties

    Science.gov (United States)

    Gold, T.

    1978-01-01

    Abstracts of 14 research reports relating to investigations of lunar samples are presented. The principal topics covered include: (1) optical properties of surface and core samples; (2) chemical composition of the surface layers of lunar grains: Auger electron spectroscopy of lunar soil and ground rock samples; (3) high frequency electrical properties of lunar soil and rock samples and their relevance for the interpretation of lunar radar observations; (4) the electrostatic dust transport process; (5) secondary electron emission characteristics of lunar soil samples and their relevance to the dust transportation process; (6) grain size distribution in surface soil and core samples; and (7) the optical and chemical effects of simulated solar wind (2keV proton and a particle radiation) on lunar material.

  13. Development and mechanical properties of structural materials from lunar simulants

    Science.gov (United States)

    Desai, Chandra S.; Girdner, K.; Saadatmanesh, H.; Allen, T.

    1991-01-01

    Development of the technologies for manufacture of structural and construction materials on the Moon, utilizing local lunar soil (regolith), without the use of water, is an important element for habitats and explorations in space. Here, it is vital that the mechanical behavior such as strength and flexural properties, fracture toughness, ductility and deformation characteristics be defined toward establishment of the ranges of engineering applications of the materials developed. The objective is to describe the research results in two areas for the above goal: (1) liquefaction of lunar simulant (at about 100 C) with different additives (fibers, powders, etc.); and (2) development and use of a new triaxial test device in which lunar simulants are first compressed under cycles of loading, and then tested with different vacuums and initial confining or in situ stress.

  14. Dosimetric properties of natural quartz grains extracted from fired materials

    DEFF Research Database (Denmark)

    Bluszcz, A.; Bøtter-Jensen, L.

    1995-01-01

    The paper describes an examination of the dosimetric properties of natural quartz grains extracted from ancient fired materials. Eleven samples of different origin were tested for their TL and GLSL (green light stimulated luminescence) sensitivities within the mGy dose range. Very promising results...... were obtained showing the possibility of measuring the doses of around 10 mGy with 1% precision using GLSL or TL and using the single aliquot technique for natural quartz as a dosimeter. The lowest detectable dose was estimated to be lower than 500 mu Gy. The results obtained indicate that natural...... quartz grains from selected materials could be used for the dosimetry of environmental gamma radiation for the purposes of paleodosimetric dating methods as well as for accident dosimetry....

  15. Pulsed power experiments in hydrodynamics and material properties

    CERN Document Server

    Reinovsky, R E

    1999-01-01

    A new application for high performance pulsed power program, the production of high energy density environments in materials for the study of material properties and hydrodynamics in complex geometries, has joined family of radiation source applications in the Stockpile Stewardship. The principle tool for producing high energy density environments is the high precision, magnetically imploded, near-solid density liner. The most attractive pulsed power system for driving such experiments is an ultra-high current, low impedance, microsecond time scale source that is economical both to build and operate. The 25-MJ Atlas capacitor bank system currently under construction at Los Alamos is the first system of its scale specifically designed to drive high precision solid liners. Delivering 30 MA, Atlas will provide liner velocities 12-15 km/sec and kinetic energies of 1-2 MJ /cm with extensive diagnostics and excellent reproducibility. Explosive flux compressor technology provides access to currents exceeding 100 MA ...

  16. Structure and Property Characterization of Oyster Shell Cementing Material

    Institute of Scientific and Technical Information of China (English)

    钟彬杨; 周强; 单昌锋; 于岩

    2012-01-01

    Oyster shell powder was used as the admixture of ordinary portland cement.The effects of different addition amounts and grinding ways on the strength and stability of cement mortar were discussed and proper addition amount of oyster shell powder was determined.The structure and property changes of cementing samples with different oyster shell powder contents were tested by XRD and SEM means.The results revealed that compressive and rupture strengths of the sample with 10% oyster shell powder was close to those of the original one without addition.Stability experiment showed that the sample prepared by pat method had smooth surface without crack and significant expansion or shrinkage after pre-curing and boiling,which indicated that cementing material dosed with oyster shell powder had fine stability.XRD and SEM observation showed that oyster shell independently exists in the cementing material.

  17. Comparison of Electrical Properties between Fluoroapatite and Hydroxyapatite Materials

    Science.gov (United States)

    Laghzizil, A.; El Herch, N.; Bouhaouss, A.; Lorente, G.; Macquete, J.

    2001-01-01

    By appropriate modifications of existing precipitation methods, apatite samples of formula M10(PO4)6X2 (M=Ca, Pb, Ba and X=F, OH) were prepared at 80°C. Samples were characterized using X-ray diffraction, infrared, 31P NMR, SEM, and chemical analysis. By comparing the effect of fluoride and hydroxide ions on ionic conductivity measurements, it was concluded that the fluorinated materials (MFAp) were better conductors than other hydroxyapatites (MHAp). The F- and H+ ions are the main charge carriers, respectively, in fluoroapatite and in hydroxyapatite compounds. The most pronounced effect on the conduction properties was observed in the lead apatite material. These results should provide important physico-chemical information for ionic diffusion of the roles played by fluoride in inhibiting dental caries.

  18. Properties and processing of nanocrystalline materials. Quarterly report

    Energy Technology Data Exchange (ETDEWEB)

    Valiev, R.Z.

    1996-01-22

    The present Report completes the investigations in the frame of the project for the first year. It is important to estimate our achievements in the investigation of properties of nanocrystalline materials obtained by severe plastic deformation and their production. We think that the main results obtained can be summarized as follows: (1) We performed an improvement of the die-set for equal channel (ECA) pressing and torsion under high pressure with the aim to increase dimensions of the samples produced and to conduct processing of low ductile materials. (2) It was established that in pure metals severe plastic deformation led to the formation of an ultra fine-grained structure with a mean grain size of 100-200 nm, while in alloys due to severe plastic deformation and/or special methods of treatment (a decrease in the temperature of deformation, an increase of the pressure applied etc.) the grain size could be decreased down to a few tens of manometers.

  19. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism. It is found that a Lorenz-type law can be used to describe the dielectric permit- tivity of either the normal ferroelectrics with or without diffuse phase transitions (DPT) or the typical ferroelectric relaxors. The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law, while the relaxor ferroelectric transition needs two independent fitting processes. The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition. Above the transition temperature, the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  20. Relaxor behavior and electrical properties of high dielectric constant materials

    Institute of Scientific and Technical Information of China (English)

    FAN HuiQing; KE ShanMing

    2009-01-01

    Several typical high dielectric constant materials are reviewed to study the electrical properties and relaxation mechanism.It is found that a Lorenz-type law can be used to describe the dielectric permitUvity of either the normal ferroelectrics with or without diffuse phase transitions(DPT)or the typical ferroelectric relaxors.The ferroelectric DPT can be well described by just one fitting process using the Lorenz-type law,while the relaxor ferroelectric transition needs two independent fitting processes.The Lorenz-type law fails at the low temperature side of the dielectric maximum of a first-order ferroelectric phase transition.Above the transition temperature,the dielectric curves of all the studied materials can be well described by a Lorenz-type law.

  1. Electronic, Vibrational and Thermoelectric Properties of Two-Dimensional Materials

    Science.gov (United States)

    Wickramaratne, Darshana

    The discovery of graphene's unique electronic and thermal properties has motivated the search for new two-dimensional materials. Examples of these materials include the layered two-dimensional transition metal dichalcogenides (TMDC) and metal mono-chalcogenides. The properties of the TMDCs (eg. MoS 2, WS2, TaS2, TaSe2) and the metal mono-chalcogenides (eg. GaSe, InSe, SnS) are diverse - ranging from semiconducting, semi-metallic and metallic. Many of these materials exhibit strongly correlated phenomena and exotic collective states such as exciton condensates, charge density waves, Lifshitz transitions and superconductivity. These properties change as the film thickness is reduced down to a few monolayers. We use first-principles simulations to discuss changes in the electronic and the vibrational properties of these materials as the film thickness evolves from a single atomic monolayer to the bulk limit. In the semiconducting TMDCs (MoS2, MoSe2, WS2 and WSe2) and monochalcogenides (GaS, GaSe, InS and InSe) we show confining these materials to their monolayer limit introduces large band degeneracies or non-parabolic features in the electronic structure. These changes in the electronic structure results in increases in the density of states and the number of conducting modes. Our first-principles simulations combined with a Landauer approach show these changes can lead to large enhancements up to an order of magnitude in the thermoelectric performance of these materials when compared to their bulk structure. Few monolayers of the TMDCs can be misoriented with respect to each other due to the weak van-der-Waals (vdW) force at the interface of two monolayers. Misorientation of the bilayer semiconducting TMDCs increases the interlayer van-der-Waals gap distance, reduces the interlayer coupling and leads to an increase in the magnitude of the indirect bandgap by up to 100 meV compared to the registered bilayer. In the semi-metallic and metallic TMDC compounds (TiSe2, Ta

  2. Optimization of the magnetic properties of materials for fluxgate sensors

    Directory of Open Access Journals (Sweden)

    Luiz Carlos de Carvalho Benyosef

    2008-06-01

    Full Text Available A study was made of the variation of the magnetic properties of cobalt-based alloys using different compositions of CoFeSiB and CoFeSiBCr systems, which were produced by the melt-spinning technique and some of them subjected to a stress annealing treatment. A comparative study of core geometry and supporting material was also performed in order to obtain low noise fluxgate sensor core using amorphous magnetic ribbons of these alloys. The best alloy was a stress annealed Co67.5Fe3.5Si17.4B11.6 sample, which yielded fluxgate sensors with lower noise levels than those of commercial crystalline materials.

  3. Fabrication of nanoscale to macroscale nickel-multiwall carbon nanotube hybrid materials with tunable material properties

    Science.gov (United States)

    Abdalla, Ahmed M.; Majdi, Tahereh; Ghosh, Suvojit; Puri, Ishwar K.

    2016-12-01

    To utilize their superior properties, multiwall carbon nanotubes (MWNTs) must be manipulated and aligned end-to-end. We describe a nondestructive method to magnetize MWNTs and provide a means to remotely manipulate them through the electroless deposition of magnetic nickel nanoparticles on their surfaces. The noncovalent bonds between Ni nanoparticles and MWNTs produce a Ni-MWNT hybrid material (NiCH) that is electrically conductive and has an enhanced magnetic susceptibility and elastic modulus. Our experiments show that MWNTs can be plated with Ni for Ni:MWNT weight ratios of γ = 1, 7, 14 and 30, to control the material properties. The phase, atom-level, and morphological information from x-ray diffraction, energy dispersive x-ray spectroscopy, scanning electron microscopy, transmission electron microscopy, dark field STEM, and atomic force microscopy clarify the plating process and reveal the mechanical properties of the synthesized material. Ni metalizes at the surface of the Pd catalyst, forming a continuous wavy layer that encapsulates the MWNT surfaces. Subsequently, Ni acts as an autocatalyst, allowing the plating to continue even after the original Pd catalyst has been completely covered. Raising γ increases the coating layer thickness from 10 to 150 nm, which influences the NiCH magnetic properties and tunes its elastic modulus from 12.5 to 58.7 GPa. The NiCH was used to fabricate Ni-MWNT macrostructures and tune their morphologies by changing the direction of an applied magnetic field. Leveraging the hydrophilic Ni-MWNT outer surface, a water-based conductive ink was created and used to print a conductive path that had an electrical resistivity of 5.9 Ω m, illustrating the potential of this material for printing electronic circuits.

  4. Hygrothermal Simulation of Foundations: Part 1 - Soil Material Properties

    Energy Technology Data Exchange (ETDEWEB)

    Kehrer, Manfred [ORNL; Pallin, Simon B [ORNL

    2012-10-01

    The hygrothermal performance of soils coupled to buildings is a complicated process. A computational approach for heat transfer through the ground has been well defined (EN ISO 13370:2007, 2007), and simplified methods have been developed (Staszczuk, Radon, and Holm 2010). However, these approaches generally ignore the transfer of soil moisture, which is not negligible (Janssen, Carmeliet, and Hens 2004). This study is divided into several parts. The intention of the first part is to gather, comprehend and adapt soil properties from Soil Science. The obtained information must be applicable to related tasks in Building Science and validated with hygrothermal calculation tools. Future parts of this study will focus on the validation aspect of the soil properties to be implemented. Basic changes in the software code may be requested at this time. Different types of basement construction will be created with a hygrothermal calculation tool, WUFI. Simulations from WUFI will be compared with existing or ongoing measurements. The intentions of the first part of this study have been fulfilled. The soil properties of interest in Building Science have been defined for 12 different soil textures. These properties will serve as input parameters when performing hygrothermal calculations of building constructions coupled to soil materials. The reliability of the soil parameters will be further evaluated with measurements in Part 2.

  5. Anticoagulation property and security of artificial heart valve material

    Institute of Scientific and Technical Information of China (English)

    WANG Xianghui; XU Jingfang; LIU Xianghuai; ZHANG Feng; LI Changrong; YU Liujiang; ZHENG Zhihong; WANG Xi; JIANG Zhenbin; CHEN Anqing

    2005-01-01

    Heart valve diseases threaten human health. One reliable way to save lives of such patients is to replace the pathologically changed heart valves by artificial ones. Over 2 million patients have received LTI-carbon heart valve's implantation. However, the thrombosis after the implantation is one of the difficulties that need to be solved. In order to improve the blood compatibility and security of mechanical heart valves, ion beam technology was used to modify the surface properties of the materials. The investigation results have been summarized in this paper.

  6. Measurement of Thermal Properties of Biosourced Building Materials

    Science.gov (United States)

    Pierre, Thomas; Colinart, Thibaut; Glouannec, Patrick

    2014-10-01

    This paper presents both experimental and theoretical works concerning the evaluation of the thermal conductivity and thermal diffusivity of hemp concrete. Experimental measurements of thermal properties are performed using a hot-strip technique for temperatures ranging from 3 to 30 and relative humidities ranging from 0 % to 95 %, thus creating a large database for this material. These experimental thermal conductivities are then compared with the results from the Krischer theoretical predictive model. The comparison shows good agreement, and a predictive analytical relation between the hemp concrete thermal conductivity, temperature, and relative humidity is determined.

  7. Preparation and properties of antimony thin film anode materials

    Institute of Scientific and Technical Information of China (English)

    SU Shufa; CAO Gaoshao; ZHAO Xinbing

    2004-01-01

    Metallic antimony thin films were deposited by magnetron sputtering and electrodeposition. Electrochemical properties of the thin film as anode materials for lithium-ion batteries were investigated and compared with those of antimony powder. It was found that both magnetron sputtering and electrodeposition are easily controllable processes to deposit antimony films with fiat charge/discharge potential plateaus. The electrochemical performances of antimony thin films, especially those prepared with magnetron sputtering, are better than those of antimony powder. The reversible capacities of the magnetron sputtered antimony thin film are above 400 mA h g-1 in the first 15 cycles.

  8. Electromagnetic properties in ferroelectric materials; Proprietes electromagnetiques des materiaux ferroelectriques

    Energy Technology Data Exchange (ETDEWEB)

    Ravez, J.; Elissalde, C. [Institut de Chimie de la Matiere Condensee, 33 - Pessac (France); Miane, J.L. [ENSCPB, 33 - Talence (France)

    1996-12-31

    The recent development of network analyzers has allowed electromagnetic property studies in perovskite-type ferroelectric materials in a large frequency range ({approx} 10{sup 2}-10{sup 10} Hz). A high frequency ({approx} 10{sup 7}-10{sup 10} Hz) relaxation has been evidenced. The origin of the relaxation process has been determined: it is an intrinsic mechanism directly related to the crystal lattice. In the light of the obtained results, physical-chemistry laws can be used to modulate the relaxation frequency using appropriate ionic substitutions. (authors). 13 refs., 6 figs., 1 tab.

  9. Mechanical properties of new dental pulp-capping materials.

    Science.gov (United States)

    Nielsen, Matthew J; Casey, Jeffery A; VanderWeele, Richard A; Vandewalle, Kraig S

    2016-01-01

    The mechanical properties of pulp-capping materials may affect their resistance to fracture during placement of a final restorative material or while supporting an overlying restoration over time. The purpose of this study was to compare the compressive strength, flexural strength, and flexural modulus of 2 new pulp-capping materials (TheraCal LC and Biodentine), mineral trioxide aggregate (MTA), and calcium hydroxide over time. Specimens were created in molds and tested to failure in a universal testing machine after 15 minutes, 3 hours, and 24 hours. The MTA specimens did not set at 15 minutes. At all time periods, TheraCal LC had the greatest compressive and flexural strengths. After 3 and 24 hours, Biodentine had the greatest flexural modulus. TheraCal LC had greater early strength to potentially resist fracture during immediate placement of a final restorative material. Biodentine had greater stiffness after 3 hours to potentially provide better support of an overlying restoration under function over time.

  10. Mechanical properties of gangue-containing aluminosilicate based cementitious materials

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    High performance aluminosilicate based cementitious materials were produced using calcined gangue as one of the major raw materials.The gangue was calcined at 500℃.The main constituent was calcined gangue, fly ash and slag, while alkali-silicate solutions were used as the diagenetic agent.The structure of gangue-containing aluminosilicate based cementitious materials was studied by the methods of IR, NMR and SEM.The results show that the mechanical properties are affected by the mass ratio between the gangue, slag and fly ash, the kind of activator and additional salt.For 28-day curing time, the compressive strength of the sample with a mass proportion of 2:1:1 (gangue: slag: fly ash) is 58.9 MPa, while the compressive strength of the sample containing 80wt%gangue can still be up to 52.3 MPa.The larger K+ favors the formation of large silicate oligomers with which Al(OH)4- prefers to bind.Therefore, in Na-K compounding activator solutions more oligomers exist which result in a stronger compressive strength of aluminosilicate-based cementitious materials than in the case of Na-containing activator.The reasons for this were found through IR and NMR analysis.Glauber's salt reduces the 3-day compressive strength of the paste, but increases its 7-day and 28-day compressive strengths.

  11. Mechanisms Responsible for Microwave Properties in High Performance Dielectric Materials

    Science.gov (United States)

    Zhang, Shengke

    Microwave properties of low-loss commercial dielectric materials are optimized by adding transition-metal dopants or alloying agents (i.e. Ni, Co, Mn) to tune the temperature coefficient of resonant frequency (tau f) to zero. This occurs as a result of the temperature dependence of dielectric constant offsetting the thermal expansion. At cryogenic temperatures, the microwave loss in these dielectric materials is dominated by electron paramagnetic resonance (EPR) loss, which results from the spin-excitations of d-shell electron spins in exchange-coupled clusters. We show that the origin of the observed magnetically-induced shifts in the dielectric resonator frequency originates from the same mechanism, as described by the Kramers-Kronig relations. The temperature coefficient of resonator frequency, tauf, is related to three material parameters according to the equation, tau f = - (½ tauepsilon + ½ taumu + alphaL), where tauepsilon, taumu , and alphaL are the temperature coefficient of dielectric constant, magnetic permeability, and lattice constant, respectively. Each of these parameters for dielectric materials of interest are measured experimentally. These results, in combination with density functional simulations, developed a much improved understanding of the fundamental mechanisms responsible for tau f. The same experimental methods have been used to characterize in-situ the physical nature and concentration of performance-degrading point defects in the dielectrics of superconducting planar microwave resonators.

  12. Game Dynamics for Players with Social and Material Preferences

    CERN Document Server

    Platkowski, Tadeusz

    2012-01-01

    We consider the dynamics, existence and stability of the equilibrium states for large populations of individuals who can play various types of non--cooperative games. The players imitate the most attractive strategies, and the choice is motivated not only by the material payoffs of the strategies, but also by their popularity in the population. The parameter which determines the weights of both factors in the equilibrium states has the same analytical form for all types of considered games, and is identified with the sensitivity to reinforcements parameter in the Hernstein's Matching Law. We prove theorems of existence and uniqueness, and discuss examples of multiple locally stable polymorphic equilibria for the considered types of games.

  13. Controlling shockwave dynamics using architecture in periodic porous materials

    Science.gov (United States)

    Branch, Brittany; Ionita, Axinte; Clements, Bradford E.; Montgomery, David S.; Jensen, Brian J.; Patterson, Brian; Schmalzer, Andrew; Mueller, Alexander; Dattelbaum, Dana M.

    2017-04-01

    Additive manufacturing (AM) is an attractive approach for the design and fabrication of structures capable of achieving controlled mechanical response of the underlying deformation mechanisms. While there are numerous examples illustrating how the quasi-static mechanical responses of polymer foams have been tailored by additive manufacturing, there is limited understanding of the response of these materials under shockwave compression. Dynamic compression experiments coupled with time-resolved X-ray imaging were performed to obtain insights into the in situ evolution of shockwave coupling to porous, periodic polymer foams. We further demonstrate shock wave modulation or "spatially graded-flow" in shock-driven experiments via the spatial control of layer symmetries afforded by additive manufacturing techniques at the micron scale.

  14. Structure and Dynamics of Nonionic Surfactant Aggregates in Layered Materials.

    Science.gov (United States)

    Guégan, Régis; Veron, Emmanuel; Le Forestier, Lydie; Ogawa, Makoto; Cadars, Sylvian

    2017-09-26

    The aggregation of surfactants on solid surfaces as they are adsorbed from solution is the basis of numerous technological applications such as colloidal stabilization, ore flotation, and floor cleaning. The understanding of both the structure and the dynamics of surfactant aggregates applies to the development of alternative ways of preparing hybrid layered materials. For this purpose, we study the adsorption of the triethylene glycol mono n-decyl ether (C10E3) nonionic surfactant onto a synthetic montmorillonite (Mt), an aluminosilicate clay mineral for organoclay preparation with important applications in materials sciences, catalysis, wastewater treatment, or as drug delivery. The aggregation mechanisms follow those observed in an analogous natural Mt, with the condensation of C10E3 in a bilayer arrangement once the surfactant self-assembles in a lamellar phase beyond the critical micelle concentration, underlining the importance of the surfactant state in solution. Solid-state (1)H nuclear magnetic resonance (NMR) at fast magic-angle spinning (MAS) and high magnetic field combined with(1)H-(13)C correlation experiments and different types of (13)C NMR experiments selectively probes mobile or rigid moieties of C10E3 in three different aggregate organizations: (i) a lateral monolayer, (ii) a lateral bilayer, and (iii) a normal bilayer. High-resolution (1)H{(27)Al} CP-(1)H-(1)H spin diffusion experiments shed light on the proximities and dynamics of the different fragments and fractions of the intercalated surfactant molecules with respect to the Mt surface. (23)Na and (1)H NMR measurements combined with complementary NMR data, at both molecular and nanometer scales, precisely pointed out the location of the C10E3 ethylene oxide hydrophilic group in close contact with the Mt surface interacting through ion-dipole or van der Waals interactions.

  15. Dynamic reconstruction of heterogeneous materials and microstructure evolution.

    Science.gov (United States)

    Chen, Shaohua; Li, Hechao; Jiao, Yang

    2015-08-01

    Reconstructing heterogeneous materials from limited structural information has been a topic that attracts extensive research efforts and still poses many challenges. The Yeong-Torquato procedure is one of the most popular reconstruction techniques, in which the material reconstruction problem based on a set of spatial correlation functions is formulated as a constrained energy minimization (optimization) problem and solved using simulated annealing [Yeong and Torquato, Phys. Rev. E 57, 495 (1998)]. The standard two-point correlation function S2 has been widely used in reconstructions, but can also lead to large structural degeneracy for certain nearly percolating systems. To improve reconstruction accuracy and reduce structural degeneracy, one can successively incorporate additional morphological information (e.g., nonconventional or higher-order correlation functions), which amounts to reshaping the energy landscape to create a deep (local) energy minimum. In this paper, we present a dynamic reconstruction procedure that allows one to use a series of auxiliary S2 to achieve the same level of accuracy as those incorporating additional nonconventional correlation functions. In particular, instead of randomly sampling the microstructure space as in the simulated annealing scheme, our procedure utilizes a series of auxiliary microstructures that mimic a physical structural evolution process (e.g., grain growth). This amounts to constructing a series auxiliary energy landscapes that bias the convergence of the reconstruction to a favored (local) energy minimum. Moreover, our dynamic procedure can be naturally applied to reconstruct an actual microstructure evolution process. In contrast to commonly used evolution reconstruction approaches that separately generate individual static configurations, our procedure continuously evolves a single microstructure according to a time-dependent correlation function. The utility of our procedure is illustrated by successfully

  16. DYNAMIC PROPERTIES OF AL-ALLOY FOAM BEAM DAMAGED BY COMPRESSIVE FATIGUE

    Institute of Scientific and Technical Information of China (English)

    Sung-Gaun Kim; Ilhyun Kim; Amkee Kim; Seung-Joon Kim; Junhong Park

    2008-01-01

    The permanent residual strain in aluminum (Al) alloy foams induced by compressive fatigue gradually increases with the increasing number of loading cycles.Consequently,the progressive shortening of Al-alloy foam degrades the dynamic material performance by the failure and ratcheting of multi-cells in the foam.In this paper,the dynamic properties of Al-alloy foams damaged by compressive fatigue were studied.The beam specimens with various residual strains were made by cyclic compression-compression stress.The dynamic bending modulus and loss factor were evaluated by using a beam transfer function method.As a result,the dynamic bending stiffness of Al-alloy foam turned out to be decreased due to damage while the loss factor was improved because of the increasing energy dissipation of such factors as cracked cell walls formed during the shortening process of the foam.The loss factor shows a manifest dependence on the fatigue residual strain.

  17. Dynamical Study of Guest-Host Orientational Interaction in LiquidCrystalline Materials

    Energy Technology Data Exchange (ETDEWEB)

    Truong, Thai Viet [Univ. of California, Berkeley, CA (United States)

    2005-01-01

    Guest-host interaction has long been a subject of interest in many disciplines. Emphasis is often on how a small amount of guest substance could significantly affect the properties of a host material. This thesis describe our work in studying a guest-host effect where dye-doping of liquid crystalline materials greatly enhances the optical Kerr nonlinearity of the material. The dye molecules, upon excitation and via intermolecular interaction, provides an extra torque to reorient the host molecules, leading to the enhanced optical Kerr nonlinearity. We carried out a comprehensive study on the dynamics of the photoexcited dye-doped liquid crystalline medium. Using various experimental techniques, we separately characterized the dynamical responses of the relevant molecular species present in the medium following photo-excitation, and thus were able to follow the transient process in which photo-excitation of the dye molecules exert through guest-host interaction a net torque on the host LC material, leading to the observed enhanced molecular reorientation. We also observed for the first time the enhanced reorientation in a pure liquid crystal system, where the guest population is created through photoexcitation of the host molecules themselves. Experimental results agree quantitatively with the time-dependent theory based on a mean-field model of the guest-host interaction.

  18. Transport properties of damaged materials. Cementitious barriers partnership

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-11-01

    The objective of the Cementitious Barriers Partnership (CBP) project is to develop tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers used in low-level waste storage applications. One key concern for the long-term durability of concrete is the degradation of the cementitious matrix, which occurs as a result of aggressive chemical species entering the material or leaching out in the environment, depending on the exposure conditions. The objective of the experimental study described in this report is to provide experimental data relating damage in cementitious materials to changes in transport properties, which can eventually be used to support predictive model development. In order to get results within a reasonable timeframe and to induce as much as possible uniform damage level in materials, concrete samples were exposed to freezing and thawing (F/T) cycles. The methodology consisted in exposing samples to F/T cycles and monitoring damage level with ultrasonic pulse velocity measurements. Upon reaching pre-selected damage levels, samples were tested to evaluate changes in transport properties. Material selection for the study was motivated by the need to get results rapidly, in order to assess the relevance of the methodology. Consequently, samples already available at SIMCO from past studies were used. They consisted in three different concrete mixtures cured for five years in wet conditions. The mixtures had water-to-cement ratios of 0.5, 0.65 and 0.75 and were prepared with ASTM Type I cement only. The results showed that porosity is not a good indicator for damage caused by the formation of microcracks. Some materials exhibited little variations in porosity even for high damage levels. On the other hand, significant variations in tortuosity were measured in all materials. This implies that damage caused by internal pressure does not necessarily create additional pore space in

  19. Cementitious barriers partnership transport properties of damaged materials

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-11-01

    The objective of the Cementitious Barriers Partnership (CBP) project is to develop tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers used in low level waste storage applications. One key concern for the long-term durability of concrete is the degradation of the cementitious matrix, which occurs as a result of aggressive chemical species entering the material or leaching out in the environment, depending on the exposure conditions. The objective of the experimental study described in this report is to provide experimental data relating damage in cementitious materials to changes in transport properties, which can eventually be used to support predictive model development. In order to get results within a reasonable timeframe and to induce as much as possible uniform damage level in materials, concrete samples were exposed to freezing and thawing (F/T) cycles. The methodology consisted in exposing samples to F/T cycles and monitoring damage level with ultrasonic pulse velocity measurements. Upon reaching pre-selected damage levels, samples were tested to evaluate changes in transport properties. Material selection for the study was motivated by the need to get results rapidly, in order to assess the relevance of the methodology. Consequently, samples already available at SIMCO from past studies were used. They consisted in three different concrete mixtures cured for five years in wet conditions. The mixtures had water-to-cement ratios of 0.5, 0.65 and 0.75 and were prepared with ASTM Type I cement only. The results showed that porosity is not a good indicator for damage caused by the formation of microcracks. Some materials exhibited little variations in porosity even for high damage levels. On the other hand, significant variations in tortuosity were measured in all materials. This implies that damage caused by internal pressure do not necessarily creates additional pore space in

  20. Effects of Fibers on the Dynamic Properties of Asphalt Mixtures

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The dynamic characteristics of fiber-modified asphalt mixture were investigated. Cellulose fiber, polyester fiber and mineral fiber were used as additives for asphalt mixture, and the dosage was 0.3%, 0.3%,0.4%, respectively. Dynamic modulus test using SuperPave simple performance tester (SPT) was conducted to study the dynamic modulus (E*) and phase angle (δ) for the control asphalt mixture and fiber-modified ones at various temperatures and frequencies. Experimental results show that all fiber-modified asphalt mixtures have higher dynamic modulus compared with control mixture. The dynamic modulus master curves of each type of asphalt mixtures are determined based on nonlinear least square regression in accordance with the timetemperature superposition theory at a control temperature (21.1 ℃). The fatigue parameter E*×sinδ and rutting parameter E*/sinδ of asphalt mixture are adopted to study the fatigue and rutting-resistance properties, and experimental results indicate that such properties can be improved by fiber additives.

  1. Final Report: Nanoscale Dynamical Heterogeneity in Complex Magnetic Materials

    Energy Technology Data Exchange (ETDEWEB)

    Kevan, Stephen [Univ. of Oregon, Eugene, OR (United States)

    2016-05-27

    A magnetic object can be demagnetized by dropping it on a hard surface, but what does ‘demagnetized’ actually mean? In 1919 Heinrich Barkhausen proved the existence of magnetic domains, which are regions of uniform magnetization that are much larger than atoms but much smaller than a macroscopic object. A material is fully magnetized when domain magnetizations are aligned, while it is demagnetized when the domain magnetizations are randomly oriented and the net magnetization is zero. The heterogeneity of a demagnetized object leads to interesting questions. Magnets are unstable when their poles align, and stable when their poles anti-align, so why is the magnetized state ever stable? What do domains look like? What is the structure of a domain wall? How does the magnetized state transform to the demagnetized state? How do domains appear and disappear? What are the statistical properties of domains and how do these vary as the domain pattern evolves? Some of these questions remain the focus of intense study nearly a century after Barkhausen’s discovery. For example, just a few years ago a new kind of magnetic texture called a skyrmion was discovered. A skyrmion is a magnetic domain that is a nanometer-scale, topologically protected vortex. ‘Topologically protected’ means that skyrmions are hard to destroy and so are stable for extended periods. Skyrmions are characterized by integral quantum numbers and are observed to move with little dissipation and so could store and process information with very low power input. Our research project uses soft x-rays, which offer very high magnetic contrast, to probe magnetic heterogeneity and to measure how it evolves in time under external influences. We will condition a soft x-ray beam so that the wave fronts will be coherent, that is, they will be smooth and well-defined. When coherent soft x-ray beam interacts with a magnetic material, the magnetic heterogeneity is imprinted onto the wave fronts and projected into

  2. Evolution properties of the community members for dynamic networks

    Science.gov (United States)

    Yang, Kai; Guo, Qiang; Li, Sheng-Nan; Han, Jing-Ti; Liu, Jian-Guo

    2017-03-01

    The collective behaviors of community members for dynamic social networks are significant for understanding evolution features of communities. In this Letter, we empirically investigate the evolution properties of the new community members for dynamic networks. Firstly, we separate data sets into different slices, and analyze the statistical properties of new members as well as communities they joined in for these data sets. Then we introduce a parameter φ to describe community evolution between different slices and investigate the dynamic community properties of the new community members. The empirical analyses for the Facebook, APS, Enron and Wiki data sets indicate that both the number of new members and joint communities increase, the ratio declines rapidly and then becomes stable over time, and most of the new members will join in the small size communities that is s ≤ 10. Furthermore, the proportion of new members in existed communities decreases firstly and then becomes stable and relatively small for these data sets. Our work may be helpful for deeply understanding the evolution properties of community members for social networks.

  3. Standard test method for dynamic tear testing of metallic materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1983-01-01

    1.1 This test method covers the dynamic tear (DT) test using specimens that are 3/16 in. to 5/8 in. (5 mm to 16 mm) inclusive in thickness. 1.2 This test method is applicable to materials with a minimum thickness of 3/16 in. (5 mm). 1.3 The pressed-knife procedure described for sharpening the notch tip generally limits this test method to materials with a hardness level less than 36 HRC. Note 1—The designation 36 HRC is a Rockwell hardness number of 36 on Rockwell C scale as defined in Test Methods E 18. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  4. Elucidating the role of interfacial materials properties in microfluidic packages.

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Thayne L.

    2013-01-01

    The purpose of this work was to discover a method to investigate the properties of interfaces as described by a numerical physical model. The model used was adopted from literature and applied to a commercially available multiphysics software package. By doing this the internal properties of simple structures could be elucidated and then readily applied to more complex structures such as valves and pumps in laminate microfluidic structures. A numerical finite element multi-scale model of a cohesive interface comprised of heterogeneous material properties was used to elucidate irreversible damage from applied strain energy. An unknown internal state variable was applied to characterize the damage process. Using a constrained blister test, this unknown internal state variable could be determined for an adherend/adhesive/adherend body. This is particularly interesting for laminate systems with microfluidic and microstructures contained within the body. A laminate structure was designed and fabricated that could accommodate a variety of binary systems joined using nearly any technique such as adhesive, welding (solvent, laser, ultrasonic, RF, etc.), or thermal. The adhesive method was the most successful and easy to implement but also one of the more difficult to understand, especially over long periods of time. Welding methods are meant to achieve a bond that is similar to bulk properties and so are easier to predict. However, methods of welding often produce defects in the bonds.. Examples of the test structures used to elucidate the internal properties of the model were shown and demonstrated. The real life examples used this research to improve upon current designs and aided in creating complex structures for sensor and other applications.

  5. The scaling properties of dynamical fluctuations in temporal networks

    CERN Document Server

    Chi, Liping

    2015-01-01

    The factorial moments analyses are performed to study the scaling properties of the dynamical fluctuations of contacts and nodes in temporal networks based on empirical data sets. The intermittent behaviors are observed in the fluctuations for all orders of the moments. It indicates that the interaction has self-similarity structure in time interval and the fluctuations are not purely random but dynamical and correlated. The scaling exponents for contacts in Prostitution data and nodes in Conference data are very close to that for 2D Ising model undergoing a second-order phase transition.

  6. The fluorescence and dynamics properties in phenoxy-phthalocyanines liquid

    Science.gov (United States)

    Yao, Cheng-Bao; Yan, Xiao-Yan; Tan, Ming-Yue; Li, Jin; Sun, Wen-Jun; Yang, Shou-Bin

    2015-06-01

    We investigated the one/two-photon fluorescence and excited state dynamics properties of two synthesized phenoxy-phthalocyanines (Pc1 and Pc2) using mild reaction coordination method. The results show that the fast decay component in the time-resolved fluorescence technique dynamics comes from the intramolecular vibrational relaxation, the slower ones from the internal conversion. Furthermore, in comparison with one-photon fluorescence spectra, the red shift of two-photon fluorescence spectra can be explained by the reabsorption effect of molecules. The samples are expected to be a potential candidate for optical applications and photodynamic therapy.

  7. Development of Thermoelectric Power Generation and Peltier Cooling Properties of Materials for Thermoelectric Cryocooling Devices

    Science.gov (United States)

    2015-05-12

    Distribution Unlimited Final Report: Development of Thermoelectric Power Generation and Peltier Cooling Properties of Materials for Thermoelectric...Thermoelectric Power Generation and Peltier Cooling Properties of Materials for Thermoelectric Cryocooling Devices Report Title The research

  8. Recommended Best Practices for the Characterization of Storage Properties of Hydrogen Storage Materials

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-03-01

    This is a reference guide to common methodologies and protocols for measuring critical performance properties of advanced hydrogen storage materials. It helps users to communicate clearly the relevant performance properties of new materials as they are discovered and tested.

  9. Organoapatites: materials for artificial bone. II. Hardening reactions and properties.

    Science.gov (United States)

    Stupp, S I; Mejicano, G C; Hanson, J A

    1993-03-01

    This article reports on chemical reactions and the properties they generated in artificial bone materials termed "organoapatites." These materials are synthesized using methodology we reported in the previous article of this series. Two different processes were studied here for the transition from organoapatite particles to implants suitable for the restoration of the skeletal system. One process involved the hardening of powder compacts by beams of blue light derived from a lamp or a laser and the other involved pressure-induced interdiffusion of polymers. In both cases, the hardening reaction involved the formation of a polyion complex between two polyelectrolytes. In the photo-induced reaction an anionic electrolyte polymerizes to form the coulombic network and in the pressure-induced one, pressure forms the complex by interdiffusion of two polyions. Model reactions were studied using various polycations. Based on these results the organoapatite selected for the study was that containing dispersed poly(L-lysine) and sodium acrylate as the anionic monomer. The organomineral particles can be pressed at room temperature into objects of great physical integrity and hydrolytic stability relative to anorganic controls. The remarkable fact about these objects is that intimate molecular dispersion of only 2-3% by weight organic material provides integrity to the mineral network in an aqueous medium and also doubles its tensile strength. This integrity is essentially nonexistent in "anorganic" samples prepared by the same methodology used in organoapatite synthesis. The improvement in properties was most effectively produced by molecular bridges formed by photopolymerization. The photopolymerization leads to the "hardening" of pellets prepared by pressing of organoapatite powders. The reaction was found to be more facile in the microstructure of the organomineral, and it is potentially useful in the surgical application of organoapatites as artificial bone.

  10. Non-equilibrium dynamics in disordered materials: Ab initio molecular dynamics simulations

    Energy Technology Data Exchange (ETDEWEB)

    Ohmura, Satoshi; Nagaya, Kiyonobu; Yao, Makoto [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan); Shimojo, Fuyuki [Department of Physics, Kumamoto University, Kumamoto 860-8555 (Japan)

    2015-08-17

    The dynamic properties of liquid B{sub 2}O{sub 3} under pressure and highly-charged bromophenol molecule are studied by using molecular dynamics (MD) simulations based on density functional theory (DFT). Diffusion properties of covalent liquids under high pressure are very interesting in the sense that they show unexpected pressure dependence. It is found from our simulation that the magnitude relation of diffusion coefficients for boron and oxygen in liquid B{sub 2}O{sub 3} shows the anomalous pressure dependence. The simulation clarified the microscopic origin of the anomalous diffusion properties. Our simulation also reveals the dissociation mechanism in the coulomb explosion of the highly-charged bromophenol molecule. When the charge state n is 6, hydrogen atom in the hydroxyl group dissociates at times shorter than 20 fs while all hydrogen atoms dissociate when n is 8. After the hydrogen dissociation, the carbon ring breaks at about 100 fs. There is also a difference on the mechanism of the ring breaking depending on charge states, in which the ring breaks with expanding (n = 6) or shrink (n = 8)

  11. Lifelong modelling of properties for materials with technological memory

    Science.gov (United States)

    Falaleev, AP; Meshkov, VV; Vetrogon, AA; Ogrizkov, SV; Shymchenko, AV

    2016-10-01

    An investigation of real automobile parts produced from dual phase steel during standard periods of life cycle is presented, which considers such processes as stamping, exploitation, automobile accident, and further repair. The development of the phenomenological model of the mechanical properties of such parts was based on the two surface plastic theory of Chaboche. As a consequence of the composite structure of dual phase steel, it was shown that local mechanical properties of parts produced from this material change significantly their during their life cycle, depending on accumulated plastic deformations and thermal treatments. Such mechanical property changes have a considerable impact on the accuracy of the computer modelling of automobile behaviour. The most significant errors of modelling were obtained at the critical operating conditions, such as crashes and accidents. The model developed takes into account the kinematics (Bauschinger effect), isotropic hardening, non-linear elastic steel behaviour and changes caused by the thermal treatment. Using finite element analysis, the model allows the evaluation of the passive safety of a repaired car body, and enables increased restoration accuracy following an accident. The model was confirmed experimentally for parts produced from dual phase steel DP780.

  12. Composition, structure and mechanical properties of several natural cellular materials

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The stem piths of sunflower, kaoliang and corn are natural cellular materials. In this paper, the contents of the compositions of these piths are determined and their cell shapes and structures are examined through scanning electron microscope (SEM) and optical microscope. Further research is conducted in the effects of the compositions and structures of the piths on the mechanical properties after testing the partial mechanical properties. The results show that the total cellulose, hemicelluloses and lignin content of each sample approaches 75% of the dry mass of its primary cell walls. With the fall of R value, a parameter relative to the contents of the main compositions, the flexibilities of the cellular piths descend while their stresses and rigidities increase. The basic cell shape making up the sunflower pith is approximately a tetrakaidehedron. The stem piths of kaoliang and corn are made up of cells close to hexangular prisms and a few tubular ones which can observably reinforce their mechanical properties in the axial directions.

  13. Relationships between nanostructure and dynamic-mechanical properties of epoxy network containing PMMA-modified silsesquioxane

    Directory of Open Access Journals (Sweden)

    2009-06-01

    Full Text Available A new class of organic-inorganic hybrid nanocomposites was obtained by blending PMMA-modified silsesquioxane hybrid materials with epoxy matrix followed by curing with methyl tetrahydrophthalic anhydride. The hybrid materials were obtained by sol-gel method through the hydrolysis and polycondensation of the silicon species of the hybrid precursor, 3-methacryloxypropyltrimethoxysilane (MPTS, simultaneously to the polymerization of the methacrylate (MMA groups covalently bonded to the silicon atoms. The nanostructure of these materials was investigated by small angle X-ray scattering (SAXS and correlated to their dynamic mechanical properties. The SAXS results revealed a hierarchical nanostructure consisting on two structural levels. The first level is related to the siloxane nanoparticles spatially correlated in the epoxy matrix, forming larger hybrid secondary aggregates. The dispersion of siloxane nanoparticles in epoxy matrix was favored by increasing the MMA content in the hybrid material. The presence of small amount of hybrid material affected significantly the dynamic mechanical properties of the epoxy networks.

  14. Electron Transport Materials: Synthesis, Properties and Device Performance

    Energy Technology Data Exchange (ETDEWEB)

    Cosimbescu, Lelia; Wang, Liang; Helm, Monte L.; Polikarpov, Evgueni; Swensen, James S.; Padmaperuma, Asanga B.

    2012-06-01

    We report the design, synthesis and characterization, thermal and photophysical properties of two silane based electron transport materials, dibenzo[b,d]thiophen-2-yltriphenylsilane (Si{phi}87) and (dibenzo[b,d]thiophen-2-yl)diphenylsilane (Si{phi}88) and their performance in blue organic light emitting devices (OLEDs). The utility of these materials in blue OLEDs with iridium (III) bis[(4,6-difluorophenyl)-pyridinato-N,C']picolinate (Firpic) as the phosphorescent emitter was demonstrated. Using the silane Si{phi}87 as the electron transport material (ETm) an EQE of 18.2% was obtained, with a power efficiency of 24.3 lm/W (5.8V at 1mA/cm{sup 2}), in a heterostructure. When Si{phi}88 is used, the EQE is 18.5% with a power efficiency of 26.0 lm/W (5.5V at 1mA/cm{sup 2}).

  15. Designing functionally graded materials with superior load-bearing properties.

    Science.gov (United States)

    Zhang, Yu; Sun, Ming-Jie; Zhang, Denzil

    2012-03-01

    Ceramic prostheses often fail from fracture and wear. We hypothesize that these failures may be substantially mitigated by an appropriate grading of elastic modulus at the ceramic surface. In this study, we elucidate the effect of elastic modulus profile on the flexural damage resistance of functionally graded materials (FGMs), providing theoretical guidelines for designing FGMs with superior load-bearing property. The Young's modulus of the graded structure is assumed to vary in a power-law relation with a scaling exponent n; this is in accordance with experimental observations from our laboratory and elsewhere. Based on the theory for bending of graded beams, we examine the effect of n value and bulk-to-surface modulus ratio (E(b)/E(s)) on stress distribution through the graded layer. Theory predicts that a low exponent (0.15graded materials with various n values and E(b)/E(s) ratios can be fabricated by infiltrating alumina and zirconia with a low-modulus glass. Flexural tests show that graded alumina and zirconia with suitable values of these parameters exhibit superior load-bearing capacity, 20-50% higher than their homogeneous counterparts. Improving load-bearing capacity of ceramic materials could have broad impacts on biomedical, civil, structural, and an array of other engineering applications.

  16. Interfacial properties and design of functional energy materials.

    Science.gov (United States)

    Sumpter, Bobby G; Liang, Liangbo; Nicolaï, Adrien; Meunier, Vincent

    2014-11-18

    CONSPECTUS: The vital importance of energy to society continues to demand a relentless pursuit of energy responsive materials that can bridge fundamental chemical structures at the molecular level and achieve improved functionality and performance. This demand can potentially be realized by harnessing the power of self-assembly, a spontaneous process where molecules or much larger entities form ordered aggregates as a consequence of predominately noncovalent (weak) interactions. Self-assembly is the key to bottom-up design of molecular devices, because the nearly atomic-level control is very difficult to realize in a top-down, for example, lithographic, approach. However, while function in simple systems such as single crystals can often be evaluated a priori, predicting the function of the great variety of self-assembled molecular architectures is complicated by the lack of understanding and control over nanoscale interactions, mesoscale architectures, and macroscale order. To establish a foundation toward delivering practical solutions, it is critical to develop an understanding of the chemical and physical mechanisms responsible for the self-assembly of molecular and hybrid materials on various support substrates. Typical molecular self-assembly involves noncovalent intermolecular and substrate-molecule interactions. These interactions remain poorly understood, due to the combination of many-body interactions compounded by local or collective influences from the substrate atomic lattice and electronic structure. Progress toward unraveling the underlying physicochemical processes that control the structure and macroscopic physical, chemical, mechanical, electrical, and transport properties of materials increasingly requires tight integration of theory, modeling, and simulation with precision synthesis, advanced experimental characterization, and device measurements. Theory, modeling, and simulation can accelerate the process of materials understanding and design

  17. Material properties of CSG for the seismic design of trapezoid-shaped CSG dam

    Energy Technology Data Exchange (ETDEWEB)

    Fujisawa, T. [Japan Dam Engineering Center, Tokyo (Japan); Nakamura, A.; Kawasaki, H.; Hirayama, D. [National Institute for Land and Infrastructure Management, Tsukuba City (Japan); Yamaguchi, Y.; Sasaki, T. [Public Works Research Institute, Tsukuba (Japan)

    2004-07-01

    Cemented Sand and Gravel (CSG) is a relatively new material in dam construction, and its physical properties are affected by gradation curves of raw material, unit water content and cement content. This paper presents an examination of the dynamic properties of CSG during cyclic loading tests simulating earthquake activity. Stress-strain curves obtained by uniaxial compression tests were confirmed as non-linear, with maximum compressive stress not exceeding the linear range of CSG. It was concluded that compared with a conventional concrete dam, stress generated in a dam body of a trapezoid-shaped CSG dam is small. In the event of an earthquake, brittle failure was presented as unlikely, due the wide range of plasticity in CSG. In a basic design of trapezoid-shaped CSG dams, the strength and modulus of elasticity in a linear range should be used as material properties of CSG. It was concluded that trapezoid-shaped CSG had a high enough safety margin against severe earthquakes. 2 refs., 2 tabs., 23 figs.

  18. Non-invasive estimation of coral tentacle material properties using underwater PIV data

    Science.gov (United States)

    Staples, Anne; Asher, Shai; Shavit, Uri

    2016-11-01

    With corals worldwide currently undergoing a third global bleaching event, understanding a detailed picture of local coral colony flow transport processes is more crucial than ever. Many coral species invest energy in extending flexible organs such as tentacles, that extrude from the coral's soft tissue surface and are used in either a passive or active manner for feeding, competitor sensing and even egg release. The significant role of these organs in transport and mixing processes is just beginning to be understood. For example, Xeniidea's rhythmic pulsation of its tentacles has recently been shown to intensify mixing and enhance photosynthesis (Kremien et al., 2013). A critical part of modeling these tentacle-induced flows is obtaining measurements of the tentacles' material properties. Obtaining such measurements, however, is challenging, since the tentacle is expected to have significantly different material properties than a harvested specimen. Here, we demonstrate a non-invasive, in situ approach for estimating these material properties forFavia favus tentacles using underwater particle image velocimetry (PIV) data and tentacle-tracking data, along with structural dynamics models of the tentacles. In this data, 2.7x2 [cm2] 1392x1024 pixel images were collected at a rate of 5 Hz 7mm above the crest of two separate Favia Favuscolonies in Eilat, Israel. Using the data and models, we are able to estimate the Young's modulus for the tentacles, which is found to be a function of the wave frequency. Partial funding by the Fulbright and Israel Science Foundations.

  19. Properties of photocured epoxy resin materials for application in piezoelectric ultrasonic transducer matching layers.

    Science.gov (United States)

    Trogé, Alexandre; O'Leary, Richard L; Hayward, Gordon; Pethrick, Richard A; Mullholland, Anthony J

    2010-11-01

    This paper describes the acoustic properties of a range of epoxy resins prepared by photocuring that are suitable for application in piezoelectric ultrasonic transducer matching layers. Materials, based on blends of diglycidyl ether of Bisphenol A and 1,4-cyclohexanedimethanol diglycidyl ether, are described. Furthermore, in order to vary the elastic character of the base resin, samples containing polymer microspheres or barium sulfate particles are also described. The acoustic properties of the materials are determined by a liquid coupled through transmission methodology, capable of determining the velocity and attenuation of longitudinal and shear waves propagating in an isotropic layer. Measured acoustic properties are reported which demonstrate materials with specific acoustic impedance varying in the range 0.88-6.25 MRayls. In the samples comprising blends of resin types, a linear variation in the acoustic velocities and density was observed. In the barium sulfate filled samples, acoustic impedance showed an approximately linear variation with composition, reflecting the dominance of the density variation. While such variations can be predicted by simple mixing laws, relaxation and scattering effects influence the attenuation in both the blended and filled resins. These phenomena are discussed with reference to dynamic mechanical thermal analysis and differential scanning calorimetry of the samples.

  20. Structural Phase Transition and Material Properties of Few-Layer Monochalcogenides

    Science.gov (United States)

    Mehboudi, Mehrshad; Fregoso, Benjamin M.; Yang, Yurong; Zhu, Wenjuan; van der Zande, Arend; Ferrer, Jaime; Bellaiche, L.; Kumar, Pradeep; Barraza-Lopez, Salvador

    2016-12-01

    GeSe and SnSe monochalcogenide monolayers and bilayers undergo a two-dimensional phase transition from a rectangular unit cell to a square unit cell at a critical temperature Tc well below the melting point. Its consequences on material properties are studied within the framework of Car-Parrinello molecular dynamics and density-functional theory. No in-gap states develop as the structural transition takes place, so that these phase-change materials remain semiconducting below and above Tc. As the in-plane lattice transforms from a rectangle into a square at Tc, the electronic, spin, optical, and piezoelectric properties dramatically depart from earlier predictions. Indeed, the Y and X points in the Brillouin zone become effectively equivalent at Tc, leading to a symmetric electronic structure. The spin polarization at the conduction valley edge vanishes, and the hole conductivity must display an anomalous thermal increase at Tc. The linear optical absorption band edge must change its polarization as well, making this structural and electronic evolution verifiable by optical means. Much excitement is drawn by theoretical predictions of giant piezoelectricity and ferroelectricity in these materials, and we estimate a pyroelectric response of about 3 ×10-12 C /K m here. These results uncover the fundamental role of temperature as a control knob for the physical properties of few-layer group-IV monochalcogenides.

  1. Dynamic properties of fuzzy Petri net model and related analysis

    Institute of Scientific and Technical Information of China (English)

    周恺卿; Azlan Mohd Zain; 莫礼平

    2015-01-01

    Fuzzy Petri net (FPN) has been extensively applied in industrial fields for knowledge-based systems or systems with uncertainty. Although the applications of FPN are known to be successful, the theoretical research of FPN is still at an initial stage. To pave a way for further study, this work explores related dynamic properties of FPN including reachability, boundedness, safeness, liveness and fairness. The whole methodology is divided into two phases. In the first phase, a comparison between elementary net system (EN_system) and FPN is established to prove that the FPN is an extensive formalism of Petri nets using a backwards-compatible extension method. Next, current research results of dynamic properties are utilized to analyze FPN model. The results illustrate that FPN model is bounded, safe, weak live and fair, and can support theoretical evidences for designing related decomposition algorithm.

  2. Nonlinear Analyses of the Dynamic Properties of Hydrostatic Bearing Systems

    Institute of Scientific and Technical Information of China (English)

    LIU Wei(刘伟); WU Xiujiang(吴秀江); V.A. Prokopenko

    2003-01-01

    Nonlinear analyses of hydrostatic bearing systems are necessary to adequately model the fluid-solid interaction. The dynamic properties of linear and nonlinear analytical models of hydrostatic bearings are compared in this paper. The analyses were based on the determination of the aperiodic border of transient processes with external step loads. The results show that the dynamic properties can be most effectively improved by increasing the hydrostatic bearing crosspiece width and additional pocket volume in a bearing can extend the load range for which the transient process is aperiodic, but an additional restrictor and capacitor (RC) chain must be introduced for increasing damping. The nonlinear analyses can also be used to predict typical design parameters for a hydrostatic bearing.

  3. Dynamical Mean-Field Theory of Electronic Correlations in Models and Materials

    Science.gov (United States)

    Vollhardt, Dieter

    2010-11-01

    The concept of electronic correlations plays an important role in modern condensed matter physics. It refers to interaction effects which cannot be explained within a static mean-field picture as provided by Hartree-Fock theory. Electronic correlations can have a very strong influence on the properties of materials. For example, they may turn a metal into an insulator (Mott-Hubbard metal-insulator transition). In these lecture notes I (i) introduce basic notions of the physics of correlated electronic systems, (ii) discuss the construction of mean-field theories by taking the limit of high lattice dimensions, (iii) explain the simplifications of the many-body perturbation theory in this limit which provide the basis for the formulation of a comprehensive mean-field theory for correlated fermions, the dynamical mean-field theory (DMFT), (v) derive the DMFT self-consistency equations, and (vi) apply the DMFT to investigate electronic correlations in models and materials.

  4. Active materials for automotive adaptive forward lighting Part 1: system requirements vs. material properties

    Science.gov (United States)

    Keefe, Andrew C.; Browne, Alan L.; Johnson, Nancy L.

    2011-04-01

    Adaptive Frontlighting Systems (AFS in GM usage) improve visibility by automatically optimizing the beam pattern to accommodate road, driving and environmental conditions. By moving, modifying, and/or adding light during nighttime, inclement weather, or in sharp turns, the driver is presented with dynamic illumination not possible with static lighting systems The objective of this GM-HRL collaborative research project was to assess the potential of active materials to decrease the cost, mass, and packaging volume of current electric stepper-motor AFS designs. Solid-state active material actuators, if proved suitable for this application, could be less expensive than electric motors and have lower part count, reduced size and weight, and lower acoustic and EMF noise1. This paper documents Part 1 of the collaborative study, assessing technically mature, commercially available active materials for use as actuators. Candidate materials should reduce cost and improve AFS capabilities, such as increased angular velocity on swivel. Additional benefits to AFS resulting from active materials actuators were to be identified as well such as lower part count. In addition, several notional approaches to AFS were documented to illustrate the potential function, which is developed more fully in Part 2. Part 1 was successful in verifying the feasibility of using two active materials for AFS: shape memory alloys, and piezoelectrics. In particular, this demonstration showed that all application requirements including those on actuation speed, force, and cyclic stability to effect manipulation of the filament assembly and/or the reflector could be met by piezoelectrics (as ultrasonic motors) and SMA wire actuators.

  5. Filter properties of seam material from paved urban soils

    Directory of Open Access Journals (Sweden)

    T. Nehls

    2008-04-01

    Full Text Available Depositions of all kinds of urban dirt and dust including anthropogenic organic substances like soot change the filter properties of the seam filling material of pervious pavements and lead to the formation of a new soil substrate called seam material.

    In this study, the impact of the particular urban form of organic matter (OM on the seam materials CECpot, the specific surface area (As, the surface charge density (SCD, the adsorption energies (Ea and the adsorption of Cd and Pb were assessed. The Cd and Pb displacement through the pavement system has been simulated in order to assess the risk of soil and groundwater contamination from infiltration of rainwater in paved urban soils.

    As, Ea and SCD derived from water vapor adsorption isotherms, CECpot, Pb and Cd adsorption isotherms where analyzed from adsorption experiments. The seam material is characterized by a darker munsell-color and a higher Corg (12 to 48g kg-1 compared to the original seam filling. Although, the increased Corg leads to higher As (16m2g-1 and higher CECpot (0.7 to 4.8cmolckg-1, with 78cmolckg-1C its specific CECpot is low compared to OM of non-urban soils. This can be explained by a low SCD of 1.2×10-6molc m-2 and a low fraction of high adsorption energy sites which is likely caused by the non-polar character of the accumulated urban OM in the seam material.

    The seam material shows stronger sorption of Pb and Cd compared to the original construction sand. The retardation capacity of seam material for Pb is similar, for Cd it is much smaller compared to natural sandy soils with similar Corg concentrations

  6. Overall Dynamic Properties of 3-D periodic elastic composites

    CERN Document Server

    Srivastava, Ankit

    2011-01-01

    A method for the homogenization of 3-D periodic elastic composites is presented. It allows for the evaluation of the averaged overall frequency dependent dynamic material constitutive tensors relating the averaged dynamic ?eld variable tensors of velocity, strain, stress, and linear momentum. The formulation is based on micromechanical modeling of a representative unit cell of a composite proposed by Nemat-Nasser & Hori (1993), Nemat-Nasser et. al. (1982) and Mura (1987) and is the 3-D generalization of the 1-D elastodynamic homogenization scheme presented by Nemat-Nasser & Srivastava (2011). We show that for 3-D periodic composites the overall compliance (stiffness) tensor is hermitian, irrespective of whether the corresponding unit cell is geometrically or materially symmetric.Overall mass density is shown to be a tensor and, like the overall compliance tensor, always hermitian. The average strain and linear momentum tensors are, however, coupled and the coupling tensors are shown to be each others'...

  7. Dynamics of intrinsic electrophysiological properties in spinal cord neurones

    DEFF Research Database (Denmark)

    Russo, R E; Hounsgaard, J

    1999-01-01

    . The intrinsic response properties of spinal neurones--determined by the particular set and distribution of voltage sensitive channels and their dynamic non-linear interactions--show a high degree of functional specialisation as reflected by the differences of intrinsic response patterns in different cell types....... Specialised, cell specific electrophysiological phenotypes gradually differentiate during development and are continuously adjusted in the adult animal by metabotropic synaptic interactions and activity-dependent plasticity to meet a broad range of functional demands....

  8. A DYNAMIC EVALUATION MODEL OF MINERAL RESOURCE PROPERTY

    Institute of Scientific and Technical Information of China (English)

    芮建伟; 冯志亮

    2000-01-01

    Based on the value theory of mineral resource, a dynamic evaluation model of mineral resource property is erected, which not only takes the factors of extractions into consideration but also those of explorations. The solution process of the model is described and the differential solution is presented. Then the paper comes to the conclusion that the differential solution is also the optimal depletion path of the resource.

  9. Doubly Dynamic Self-Healing Materials Based on Oxime Click Chemistry and Boronic Acids.

    Science.gov (United States)

    Collins, Joe; Nadgorny, Milena; Xiao, Zeyun; Connal, Luke A

    2017-03-01

    The dynamic covalent characteristics of oxime and boronate ester bonds have been explored. A small excess of a competing aldehyde under acidic conditions resulted in oxime polymer degradation from high molecular weights (30 kDa) to low molecular weight oligomers (2.2 kDa). The dynamic nature of oxime bonds imparts oxime cross-linked hydrogels with self-healing properties and the incorporation of phenyl boronic acid groups into the hydrogel network provides a platform for hydrogel functionalization. The addition of a polyphenol (tannic acid) proves a facile means to incorporate a second, dynamic covalent cross-linking network through boronate ester formation which, owing to the increase in the degree of cross-linking, is found to be nearly double the hydrogel strength (storage modulus increased from 4.6 to 8.5 kPa). Finally, the tannic acid cross-linking network is selectively degraded returning the hydrogel storage modulus to its initial value and providing a means for the synthesis of materials with tunable mechanical properties. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Mechanical behavior of ultrafine-grained materials under combined static and dynamic loadings

    Directory of Open Access Journals (Sweden)

    Guo Y.Z.

    2015-01-01

    Full Text Available Ultrafine-grained (UFG materials have extensive prospects for engineering application due to their excellent mechanical properties. However, the grain size decrease reduces their strain hardening ability and makes UFG materials more susceptible to deformation instability such as shear localization. In most cases, critical shear strain is taken as the criterion for formation of shear localization under impact loading or adiabatic shear band (ASB. Recently, some researchers found that the formation of ASB was determined only by the dynamic loading process and had nothing to do with its static loading history. They proposed for coarse-grained metals a dynamic stored energy-based criterion for ASB and verified it by some experiments. In this study, we will focus on the shear localization behavior of UFG metals such as UFG titanium and magnesium alloy AZ31. Quasi-static loading and dynamic loading will be applied on the same specimen alternately. The shear localization behavior will be analyzed and the criterion of its formation will be evaluated.

  11. Coupled light transport-heat diffusion model for laser dosimetry with dynamic optical properties

    Energy Technology Data Exchange (ETDEWEB)

    London, R.A.; Glinsky, M.E.; Zimmerman, G.B.; Eder, D.C. [Lawrence Livermore National Lab., CA (United States); Jacques, S.L. [Texas Univ., Houston, TX (United States). M.D. Anderson Cancer Center

    1995-03-01

    The effect of dynamic optical properties on the spatial distribution of light in laser therapy is studied via numerical simulations. A two-dimensional, time dependent computer program called LATIS is used. Laser light transport is simulated with a Monte Carlo technique including anisotropic scattering and absorption. Thermal heat transport is calculated with a finite difference algorithm. Material properties are specified on a 2-D mesh and can be arbitrary functions of space and time. Arrhenius rate equations are solved for tissue damage caused by elevated temperatures. Optical properties are functions of tissue damage, as determined by previous measurements. Results are presented for the time variation of the light distribution and damage within the tissue as the optical properties of the tissue are altered.

  12. Characterisation of Dynamic Mechanical Properties of Resistance Welding Machines

    DEFF Research Database (Denmark)

    Wu, Pei; Zhang, Wenqi; Bay, Niels

    2005-01-01

    The dynamic mechanical properties of a resistance welding machine have significant influence on weld quality, which must be considered when simulating the welding process numerically. However, due to the complexity of the machine structure and the mutual coupling of components of the machine system...... characterizing the dynamic mechanical characteristics of resistance welding machines is suggested, and a test set-up is designed determining the basic, independent machine parameters required in the model. The model is verified by performing a series of mechanical tests as well as real projection welds......., it is very difficult to measure or calculate the basic, independent machine parameters required in a mathematical model of the machine dynamics, and no test method has so far been presented in literature, which can be applied directly in an industrial environment. In this paper, a mathematical model...

  13. Dynamical topology and statistical properties of spatiotemporal chaos.

    Science.gov (United States)

    Zhuang, Quntao; Gao, Xun; Ouyang, Qi; Wang, Hongli

    2012-12-01

    For spatiotemporal chaos described by partial differential equations, there are generally locations where the dynamical variable achieves its local extremum or where the time partial derivative of the variable vanishes instantaneously. To a large extent, the location and movement of these topologically special points determine the qualitative structure of the disordered states. We analyze numerically statistical properties of the topologically special points in one-dimensional spatiotemporal chaos. The probability distribution functions for the number of point, the lifespan, and the distance covered during their lifetime are obtained from numerical simulations. Mathematically, we establish a probabilistic model to describe the dynamics of these topologically special points. In spite of the different definitions in different spatiotemporal chaos, the dynamics of these special points can be described in a uniform approach.

  14. Dynamic properties of epidemic spreading on finite size complex networks

    Institute of Scientific and Technical Information of China (English)

    Li Ying; Liu Yang; Shan Xiu-Ming; Ren Yong; Jiao Jian; Qiu Ben

    2005-01-01

    The Internet presents a complex topological structure, on which computer viruses can easily spread. By using theoretical analysis and computer simulation methods, the dynamic process of disease spreading on finite size networks with complex topological structure is investigated. On the finite size networks, the spreading process of SIS (susceptibleinfected-susceptible) model is a finite Markov chain with an absorbing state. Two parameters, the survival probability and the conditional infecting probability, are introduced to describe the dynamic properties of disease spreading on finite size networks. Our results can help understanding computer virus epidemics and other spreading phenomena on communication and social networks. Also, knowledge about the dynamic character of virus spreading is helpful for adopting immunity policy.

  15. Characterisation of Dynamic Mechanical Properties of Resistance Welding Machines

    DEFF Research Database (Denmark)

    Wu, Pei; Zhang, Wenqi; Bay, Niels

    2005-01-01

    The dynamic mechanical properties of a resistance welding machine have significant influence on weld quality, which must be considered when simulating the welding process numerically. However, due to the complexity of the machine structure and the mutual coupling of components of the machine system......, it is very difficult to measure or calculate the basic, independent machine parameters required in a mathematical model of the machine dynamics, and no test method has so far been presented in literature, which can be applied directly in an industrial environment. In this paper, a mathematical model...... characterizing the dynamic mechanical characteristics of resistance welding machines is suggested, and a test set-up is designed determining the basic, independent machine parameters required in the model. The model is verified by performing a series of mechanical tests as well as real projection welds....

  16. Quantitative property-structural relation modeling on polymeric dielectric materials

    Science.gov (United States)

    Wu, Ke

    Nowadays, polymeric materials have attracted more and more attention in dielectric applications. But searching for a material with desired properties is still largely based on trial and error. To facilitate the development of new polymeric materials, heuristic models built using the Quantitative Structure Property Relationships (QSPR) techniques can provide reliable "working solutions". In this thesis, the application of QSPR on polymeric materials is studied from two angles: descriptors and algorithms. A novel set of descriptors, called infinite chain descriptors (ICD), are developed to encode the chemical features of pure polymers. ICD is designed to eliminate the uncertainty of polymer conformations and inconsistency of molecular representation of polymers. Models for the dielectric constant, band gap, dielectric loss tangent and glass transition temperatures of organic polymers are built with high prediction accuracy. Two new algorithms, the physics-enlightened learning method (PELM) and multi-mechanism detection, are designed to deal with two typical challenges in material QSPR. PELM is a meta-algorithm that utilizes the classic physical theory as guidance to construct the candidate learning function. It shows better out-of-domain prediction accuracy compared to the classic machine learning algorithm (support vector machine). Multi-mechanism detection is built based on a cluster-weighted mixing model similar to a Gaussian mixture model. The idea is to separate the data into subsets where each subset can be modeled by a much simpler model. The case study on glass transition temperature shows that this method can provide better overall prediction accuracy even though less data is available for each subset model. In addition, the techniques developed in this work are also applied to polymer nanocomposites (PNC). PNC are new materials with outstanding dielectric properties. As a key factor in determining the dispersion state of nanoparticles in the polymer matrix

  17. Static and dynamic mechanical properties of amorphous recycled poly-(ethylene terepthalate)

    Science.gov (United States)

    Rajakutty, Arjun

    Scope and Method of Study: Polymers are among the largest used materials today in the world. PET has a significant market share among all the other polymers. More than 90% of plastic bottles made in the world are from PET. With this huge amount of material being used, the impact on the environment in the form of increasing landfills and carbon dioxide emissions has also been high. Hence the need to recycle PET and reuse it has been a topic of interest over the last few years. However, loss in properties of recycled PET (rPET) has been a concern and it is still considered secondary to virgin PET. This work was aimed at studying the mechanical properties of rPET and comparing these properties with those from virgin PET. The dynamic behavior of PET was part of this study. Apart from studying the mechanical properties of rPET, several other tests were performed to study thermal properties, crystallinity, color measurements (yellowing), friction behavior and also to determine structural performance of blow molded bottles. Material properties obtained from experimental results were used as input for Finite Element simulations. Findings and Conclusions: The findings and results from this research have provided a framework to understand the mechanical properties of rPET. The method of tensile testing using the custom fixture was an efficient means of determining bulk mechanical properties. rPET was found to have properties similar to virgin PET resins with dynamic measurements showing the greatest differences near 100 mm/min. The dynamic properties with increasing strain rates generally fit power law or exponential curves. DSC measurements along the preform helped to understand the crystallinity distribution and validate the new tensile sample injection method. Strain induced crystallization was also observed. Color measurements provided a good indication of the yellowness index values in rPET and changes in these values on addition of coloring agents. Top load and hoop

  18. Composite Materials with Magnetically Aligned Carbon Nanoparticles Having Enhanced Electrical Properties and Methods of Preparation

    Science.gov (United States)

    Hong, Haiping (Inventor); Peterson, G.P. (Bud) (Inventor); Salem, David R. (Inventor)

    2016-01-01

    Magnetically aligned carbon nanoparticle composites have enhanced electrical properties. The composites comprise carbon nanoparticles, a host material, magnetically sensitive nanoparticles and a surfactant. In addition to enhanced electrical properties, the composites can have enhanced mechanical and thermal properties.

  19. Superconducting and normal-state properties of novel materials

    Energy Technology Data Exchange (ETDEWEB)

    Crespi, Vincent Henry [Univ. of California, Berkeley, CA (United States)

    1994-09-01

    Interest in solid state physics naturally gravitates towards novel systems such as the copper oxide superconductors or the alkali-doped fullerenes. This paper tackles high temperature superconductivity by extension of the BCS theory for ordinary superconductors, in particular, incorporation of anharmonicity in phonon dynamics and anisotropy in electron-phonon coupling. These refinements can account for many anomalous properties of the cuprates. Phonon anharmonicity is consistent with a small isotope effect at optimal doping and a larger isotope effect in suboptimal systems. Anisotropy in the interaction, a plausible consequence of certain anharmonic models, can circumvent objections to electron-phonon coupling based on transport measurements. Such anisotropy is consistent with gap anisotropy and strong temperature dependence of Hall coefficient. In contrast to cuprates, the doped fullerenes appear understandable within the standard model of single electron band theory and BCS theory. Microscopic parameters derivable from transport and critical field measurements yield a self-consistent picture of a disordered Type-2 BCS superconductor. Isotope effects imply that superconductivity is mediated by carbon phonons opposed to alkali atom vibrations. The novel properties of the fullerenes are generally traceable to their microscopic heterogeneity, being a collection of tightly bound but weakly overlapping molecules. Separation of electronic regimes into weak intermolecular overlap and strong carbon-carbon on-ball bonds yields a superconductor with both a large density of states and a high phonon frequency, properties consistent with a relatively high {Tc}. Disordered nature of intermolecular overlap produces a large residual resistivity and a universal dependence to the Hall coefficient. This disorder is also consistent with the anomalously large carbon isotope effect for heterogeneous isotopic substitution.

  20. Dynamic impact of granular material on a vertical obstacle

    Science.gov (United States)

    Rossi, Giulia; Armanini, Aronne; Larcher, Michele

    2017-04-01

    Debris flows are rapid to very rapid flows, made up of a high concentrated mixture of water and sediments. These types of flow are catastrophic natural phenomena affecting mountain areas and causing several property damages and loss of lives. The mitigation of these phenomena is then fundamental: the check dams are among the main structural countermeasures. A crucial aspect in the definition of the design criteria for these structures is the analysis of the impact force exerted by a debris flow on them. From a scientific point of view, the state of art in this field still has aspects that are not fully clear. There are two main approaches adopted: the first one considers the force of dynamic impact exerted on a structure proportional to the hydrostatic pressure. However, from a theoretical point of view, this approach is not so reliable, since the hydrodynamic nature of the phenomenon probably induces pressures on the structure higher than the hydrostatic values. On the other hand, the second approach assumes the force of the dynamic impact proportional to the square of the velocity of the flow, considering the dynamic nature of the impact. According to Armanini and Scotton (1992), two main types of impact may occur. The first type is characterized by the formation of a reflected wave after the impact, which propagates upstream. A convincing theoretical solution of this problem is achieved through the application of the conservation of mass and momentum equations with respect to a volume control that moves with the reflected wave (Armanini 2009) under the hypothesis of homogeneous fluid. The second type of impact consists of a complete deviation of the flow along the vertical obstacle, assuming a jet-like behavior. The previous theoretical scheme cannot be applied in this situation, but it must be suitably modified. In order to better understand the kinematic characteristics of the phenomenon, the debris flow dynamic impact against a vertical wall has been studied