WorldWideScience

Sample records for dust fibre amosite

  1. Lung dust analysis in the assessment of past exposure of man-made mineral fibre workers.

    Science.gov (United States)

    McDonald, J C; Case, B W; Enterline, P E; Henderson, V; McDonald, A D; Plourde, M; Sébastien, P

    1990-10-01

    In the cohort of American MMMF workers reported by ENTERLINE et al. [Ann. occup. Hyg. 31, 625-656 (1987)] autopsies were recorded in 652 (13.5%) of 4840 deaths. Lung tissue samples were sought from all pathologists and obtained in 145 (22.2%), together with similar samples from 124 matched referents. Lung fibre counts by phase contrast microscopy were 60% higher (P less than 0.05) in workers than referents. Electron microscopy (ATEM) also showed more fibres of all kinds--MMMF, asbestos and other--but no convincing excess of any one type. Lung samples of only 26% of workers contained any MMMF, almost all siliceous in nature and in low concentration. There were too few cases of lung cancer (19) for any useful conclusion; however, in the plant with the highest lung cancer SMR (200), and a probable mesothelioma, amosite at greater than 1.0 fibres per micrograms (f micrograms-1) was found in four of six workers but in none of their matched referents. Although our findings contribute little to the interpretation of the results obtained by ENTERLINE et al. they indicate the potential value of tissue analyses in monitoring epidemiological studies of MMMF exposure.

  2. Comparison of length-dependent cytotoxicity of inhalable asbestos and man-made mineral fibres.

    Science.gov (United States)

    Tilkes, F; Beck, E G

    1980-01-01

    Fibres of various defined length distributions were tested in vitro and in vivo. Tumour cells with phagocytic ability were used as the in vitro test system. DNA and protein synthesis and cell proliferation and enzyme release (LDH) were determined. Using gravimetrical and numerical doses in cultures, good indications of the toxicity of single fibres were found. It was possible to demonstrate clear-cut relationships between fibre length and cytotoxicity. In this test system, the toxicity of fibres increases with increasing length. The results of the cell experiments also furnish important indications of the doses of fibrous dusts to be used in animal tests and of the possibility of comparing different fibres with each other, especially with respect to the numerical or gravimetrical quantification of fibre fractions. Amosite, chrysotile, crocidolite and glass fibres of three or four different length spectra were tested.

  3. The distribution of amosite asbestos in the periphery of the normal human lung.

    OpenAIRE

    Churg, A

    1990-01-01

    Although theoretical models and experiments on animals exist that predict the distribution of asbestos fibres in the lung, there are few studies in man that relate to this question and they have generated contradictory results. To examine this distribution analytical electron microscopy was employed to determine the amosite fibre concentration, size, surface area, and mass in 29 circumferential sites around the periphery of a mid-sagittal slice from nine morphologically normal left lungs of h...

  4. Experimental study on the strength parameter of Quarry Dust mixed Coconut Shell Concrete adding Coconut Fibre

    Science.gov (United States)

    Matangulu Shrestha, Victor; Anandh, S.; Sindhu Nachiar, S.

    2017-07-01

    Concrete is a heterogeneous mixture constitute of cement as the main ingredient with a different mix of fine and coarse aggregate. The massive use of conventional concrete has a shortfall in its key ingredients, natural sand and coarse aggregate, due to increased industrialisation and globalisation. To overcome the shortage of material, an alternate material with similar mechanical properties and composition has to be studied, as replacement of conventional concrete. Coconut shell concrete is a prime option as replacement of key ingredients of conventional concrete as coconut is produced in massive quantity in south East Asia. Coconut shell concrete is lightweight concrete and different research is still ongoing concerning about its mix design and composition in the construction industry. Concrete is weak in tension as compared to compression, hence the fibre is used to refrain the crack in the concrete. Coconut fibre is one of many fibres which can be used in concrete. The main aim of this project is to analyse the use of natural by-products in the construction industry, make light weight concrete and eco-friendly construction. This project concerns with the comparison of the mechanical properties of coconut shell concrete and conventional concrete, replacing fine aggregate with quarry dust using coconut fibre. M25 grade of concrete was adopted and testing of concrete was done at the age of 3, 7 and 28 days. In this concrete mix, sand was replaced completely in volumetric measurement by quarry dust. The result was analysed and compared with addition of coconut fibre at varying percentage of 1%, 2%, 3%, 4% and 5%. From the test conducted, coconut shell concrete with quarry dust has the maximum value at 4% of coconut fibre while conventional concrete showed the maximum value at 2% of coconut fibre.

  5. Carcinogenicity studies on fibres, metal compounds, and some other dusts in rats.

    Science.gov (United States)

    Pott, F; Ziem, U; Reiffer, F J; Huth, F; Ernst, H; Mohr, U

    1987-01-01

    About 50 dusts were examined on their carcinogenicity in rats mainly after intraperitoneal injection and some after intratracheal instillation. In the i.p. test, very low doses between 0.05 and 0.5 mg asbestos led to tumour incidences of about 20 to 80%. Polyvinyl-pyridine-N-oxide prolonged the tumour latency after injection of actinolite. 60 mg attapulgite from three sources with short fibre lengths were not shown to be carcinogenic but an attapulgite sample with longer fibres had a moderate effect. Relatively thick rock and ceramic fibres (median greater than 1 micron) induced tumours, but slag and wollastonite fibres did not, probably because of their better solubility. Intratracheal instillations of glass microfibres (20 X 0.5 mg) led to lung tumours in 5 of 34 rats (0 in control). The carcinogenic potency of an inorganic fibre depends on its size and persistency, and possibly also on other properties, especially on the surface. Nickel powder, nickel oxide, nickel subsulfide and cadmium sulfide were all found to be carcinogenic in the two tests. Cadmium chloride and cadmium oxide could only be administered in very low doses because of their high acute toxicity. A high amount of magnetite (15 X 15 mg i.tr.) led to an unexpected lung tumour incidence of 69%. The i.p. test in rats proved to be very sensitive for detecting the carcinogenic potency of non-acute toxic natural and man-made mineral dusts as well as metal compounds. This means that, if a high dose of one of these dusts does not induce tumours in this test, no suspicion of carcinogenic potency can be substantiated.

  6. Hydrogen peroxide release and hydroxyl radical formation in mixtures containing mineral fibres and human neutrophils.

    Science.gov (United States)

    Leanderson, P; Tagesson, C

    1992-11-01

    The ability of different mineral fibres (rock wool, glass wool, ceramic fibres, chrysotile A, chrysotile B, amosite, crocidolite, antophyllite, erionite, and wollastonite) to stimulate hydrogen peroxide (H2O2) and hydroxyl radical (OH.) formation in mixtures containing human polymorphonuclear leucocytes (PMNLs) was investigated. In the presence of azide, all the fibres caused considerable H2O2 formation, and about twice as much H2O2 was found in mixtures with the natural fibres (asbestos, erionite, and wollastonite) than in mixtures with the manmade fibres (rock wool, glass wool, and ceramic fibres). In the presence of externally added iron, all the fibres were found to generate OH. and the natural fibres caused about three times more OH. formation than the manmade fibres. In the absence of external iron, there was less OH. formation; however, amosite, crocidolite, antophyllite, erionite, and wollastonite still generated considerable amounts of OH., also under circumstances in which only small amounts of OH. were produced in mixtures with the manmade fibres. These findings indicate that natural fibres generate more H2O2 and OH. than manmade fibres when incubated with PMNLs in the presence of external iron. They also suggest that the natural fibres, amosite, crocidolite, antophyllite, erionite, and wollastonite may act catalytically in the dissociation of H2O2 to OH. in the absence of external iron, whereas manmade fibres such as rock wool, glass wool, and ceramic fibres, do not seem to be able to generate OH. in the absence of external iron.

  7. Detection of surface free radical activity of respirable industrial fibres using supercoiled phi X174 RF1 plasmid DNA.

    Science.gov (United States)

    Gilmour, P S; Beswick, P H; Brown, D M; Donaldson, K

    1995-12-01

    The ability of a number of respirable industrial fibres, amosite and crocidolite asbestos, refractory ceramic fibres (RCFs) and man-made vitreous fibres (MMVFs) to cause free radical injury to plasmid phi X174 RFI DNA was assessed. The oxidative DNA damage was observed as depletion of supercoiled DNA after fibre treatment was quantified by scanning laser densitometry. The mechanism of fibre-mediated damage was determined by the use of the specific hydroxyl radical scavenger mannitol and the iron chelator desferrioxamine-B. The amosite and crocidolite asbestos caused substantial damage to DNA that was dose-related. The free radicals responsible for the asbestos-mediated DNA damage were hydroxyl radicals, as determined by inhibition with mannitol. Asbestos fibre-mediated damage to DNA was completely ameliorated by the chelation of fibre-associated iron with desferrioxamine-B. The amount of Fe(II) and Fe(III) released by equal numbers of the different fibre types at equal fibre number was determined. The fibres released very small amounts of Fe(II) and there were no significant differences between the fibre types. The fibres released substantial amounts of Fe(III); MMVF 21 released significantly more Fe(III) than any of the other fibres and short fibre amosite also released more Fe(III) than three of the MMVFs and two of the RCFs. When ability to release Fe(II) and Fe(III) was compared with ability to cause DNA damage there was not a good correlation, because only the long amosite and crocidolite caused substantial free radical injury to DNA; this contrasts with MMVF 21 and short amosite being the two fibres that released the greatest amounts of iron. The loss of ability to damage DNA in DSF-B-treated asbestos fibres shows that iron at the surface of asbestos fibres definitely has a role in generating hydroxyl radicals. However, it is clear that some fibres, such as short amosite and MMVF 21, release large quantities of iron without causing free radical damage, whilst

  8. Mineral fibres and cancer.

    Science.gov (United States)

    McDonald, J C

    1984-04-01

    A synthesis is presented of the salient findings to date from laboratory and epidemiological research, on the health effects of asbestos and other natural and man-made mineral fibres. Experimental evidence suggests that all mineral fibres are capable of causing fibrosis and malignancy, with chrysotile at least as pathogenic as other fibres. However, penetration, retention and phagocytosis are affected by size and shape and reactivity and durability by physico-chemical properties. Thus it is not surprising that in man the results of exposure vary considerably with fibre type and industrial process. A considerable body of evidence suggests that chrysotile has seldom, if ever, caused peritoneal mesothelioma and that the great majority of pleural mesotheliomas are also attributable to crocidolite or amosite. Without more reliable information on intensity and duration of exposure by fibre type, the epidemiological evidence on this point cannot be wholly conclusive. There are stronger grounds from a limited number of cohort studies for believing that in relation to estimated exposure, the risk of lung cancer has been much higher in textile plants than in fibre production or in the manufacture of friction products, with asbestos-cement plants somewhere in between. The data on man-made fibre production remains equivocal. It is concluded that attempts to regulate asbestos without regard for fibre type, although perhaps adequate for lung cancer and fibrosis, may do little to reduce the risk of mesothelioma. The search for safe fibre substitutes for asbestos will remain difficult until the parameters of pathogenicity are better understood.

  9. Hydrogen peroxide release and hydroxyl radical formation in mixtures containing mineral fibres and human neutrophils.

    OpenAIRE

    Leanderson, P; Tagesson, C

    1992-01-01

    The ability of different mineral fibres (rock wool, glass wool, ceramic fibres, chrysotile A, chrysotile B, amosite, crocidolite, antophyllite, erionite, and wollastonite) to stimulate hydrogen peroxide (H2O2) and hydroxyl radical (OH.) formation in mixtures containing human polymorphonuclear leucocytes (PMNLs) was investigated. In the presence of azide, all the fibres caused considerable H2O2 formation, and about twice as much H2O2 was found in mixtures with the natural fibres (asbestos, eri...

  10. TWO-WEEK INHALATION EXPOSURE OF RATS TO LIBBY AMPHIBOLE (LA) AND AMOSITE ASBESTOS

    Science.gov (United States)

    The relative potency of LA compared to UICC amosite was assessed in a subacute inhalation study designed to set exposure levels for a future subchronic study. Male F344 rats (n=7/group) were exposed nose-only to air (control), 3 concentrations of LA, or I concentration of amosite...

  11. TWO-WEEK INHALATION EXPOSURE OF RATS TO LIBBY AMPHIBOLE (LA) AND AMOSITE ASBESTOS

    Science.gov (United States)

    The relative potency of LA compared to UICC amosite was assessed in a subacute inhalation study designed to set exposure levels for a future subchronic study. Male F344 rats (n=7/group) were exposed nose-only to air (control), 3 concentrations of LA, or I concentration of amosite...

  12. Low dose effects of fibrous and non-fibrous mineral dusts on the proliferation of mammalian cells in vitro.

    Science.gov (United States)

    Fischer, A B; Kaw, J L; Diemer, K; Eikmann, T

    1998-08-01

    This report presents preliminary results of studies on the growth stimulating properties of mineral dusts. The studies were carried out with Syrian hamster diploid embryonic fibroblasts and Chinese hamster fibroblasts, line B14F28. Toxicity testing was done by the determination of the plating efficiency as a measure of growth and viability. The following dusts were used: the modified UICC asbestos fibres amosite, (AFF) crocidolite (KFF), chrysotile (KFF): in addition glass fibre (GFF), corundum and quartz DQ12. Concentrations > 2 microg/cm2 of AFF, CFF, KFF and GFF depressed the plating efficiency of B14F28 cells in a dose-dependent manner, but all of the fibres and corundum increased colony sizes at concentrations of 0.16-0.33 microg/cm2, in the case of corundum, AFF, KFF, and CFF also at up to 0.66 or 1.32 microg/cm2. DQ12 did not enhance colony growth. The stimulation of proliferation could be demonstrated both in terms of colony size (diameter) and cell numbers. The factor(s) responsible for proliferation stimulation reside in the supernatant, since the medium of dust-treated cell cultures was able to stimulate colony growth after removal of the dusts by filtration. The results indicate the induction of growth factors (cytokines) by low concentrations of the mineral dusts. Experiments concerning the effect of dusts on embryonic golden hamster fibroblasts yielded similar results. The plating efficiency was inhibited by concentrations of GFF and CFF > 0.25 microg cm2 and by AFF, KFF, GFF and corundum at concentrations > 5 microg/cm2, but colony counts were significantly increased by AFF, KFF and corundum at concentrations of 0.25-3 microg/cm2. This biological reaction which was observed in different cell types appears to be especially relevant in the context of environmental exposure where low dust concentrations prevail.

  13. Influence of fibre length, dissolution and biopersistence on the production of mesothelioma in the rat peritoneal cavity.

    Science.gov (United States)

    Miller, B G; Searl, A; Davis, J M; Donaldson, K; Cullen, R T; Bolton, R E; Buchanan, D; Soutar, C A

    1999-04-01

    A range of respirable man-made mineral fibres were tested for evidence of carcinogenicity by injection into the peritoneal cavity of male SPF Wistar rats; and differences in carcinogenicity were related to the dimensions and biopersistence of the injected fibres. The fibres tested included an amosite asbestos, a silicon carbide whisker, a special purpose glass microfibre, and a range of other man-made vitreous fibres (MMVFs) and refractory ceramic fibres (RCFs) from the TIMA fibre repository. The injected dose of each was designed as the estimated mass required to contain 10(9) fibres > 5 microns in length, as determined by optical microscopy. The numbers of long fibres (> 15 microns) contained in these doses ranged across fibres from 0.1 x 10(9) to 0.8 x 10(9) fibres; the number of long fibres thinner than 0.95 micron ranged from 0.015 x 10(9) to 0.4 x 10(9). The treatment groups contained between 18 and 24 animals. Animals were killed when they showed signs of debilitation. At autopsy, the diagnosis of mesothelioma was usually obvious macroscopically. Otherwise, histological examination of peritoneal organs was used to search for early tumour development. Judged by median survival time, four of the fibre types, in the doses administered, presented higher mesothelioma activity than amosite asbestos. The other fibres tested were less carcinogenic than the amosite. Only a ceramic material derived by extreme heating to simulate the effect of furnace or oven conditions, produced no mesotheliomas. Attempts were made, using regression models, to relate these differences to fibre dimensions and to measures of durability from separate experiments. The results pointed principally to a link with the injected numbers of fibres > 20 microns in length and with biopersistence in the rat lung of fibres longer than 5 microns. Improved quantification of the relative importance of fibre dimensions and biopersistence indices requires experimentation with a range of doses.

  14. Fibrogenesis by mineral fibres: an in-vitro study of the roles of the macrophage and fibre length.

    Science.gov (United States)

    Aalto, M; Heppleston, A G

    1984-02-01

    Evidence on the mechanism by which inhaled mineral fibres lead to pulmonary fibrosis has not been forthcoming. As with silica, a biphasic cell culture system was required to distinguish phagocytosis from collagen formation. Synthesis of total protein and collagen by rat fibroblasts was estimated by incorporation of labelled proline after treatment with the medium from rat peritoneal macrophages that had been cultured in the presence of different types of mineral fibre. The influence of fibre length was also examined. All the main varieties of asbestos reacted with macrophages to produce or release a fibrogenic factor. However, chrysotile and the longer amosite fibres evoked the response only after prolonging the period of incubation with macrophages, presumably by permitting more complete phagocytosis of curled or longer fibres. Short amosite fibres proved to be more active than longer ones and under certain conditions were as potent as quartz. Fibrous glass also possessed stimulatory properties and again a sample having a short length gave a stronger response than a long one. Collagen formation by asbestos thus appears to be mediated by a macrophage factor, so operating in a manner similar to that previously demonstrated for quartz. The conventional view that short fibres are comparatively insignificant in asbestos fibrogenesis cannot, on the present evidence, be sustained. Furthermore, it should not be assumed than man-made mineral fibres of respirable diameter are innocuous or that short ones can be ignored.

  15. Supercoiled plasmid DNA as a model target for assessing the generation of free radicals at the surface of fibres.

    Science.gov (United States)

    Donaldson, K; Gilmour, P S; Beswick, P H

    1995-09-01

    The ability of respirable amosite and crocidolite asbestos, refractory ceramic fibres (RCFs) and man made vitreous fibres (MMVFs) to cause free radical injury to plasmid, phiX174 RFI DNA was assessed. The amosite and crocidolite asbestos caused substantial damage to the DNA and, in the main, the free radicals responsible for the asbestos-mediated DNA damage were hydroxyl radicals as determined by inhibition with mannitol. Asbestos fibre-mediated damage to the DNA was completely ameliorated by the chelation of fibre-associated iron by pre-treatment of fibres with desferrioxamine-B, confirming the importance of iron in the production of free radicals. MMVFs and RCFs produced modest free radical damage to the DNA, which was prevented by mannitol but not by iron chelation.

  16. Persistent Effects of Libby Amphibole and Amosite Asbestos Following Subchronic Inhalation in Rats

    Science.gov (United States)

    Background: Human exposure to Libby amphibole (LA) asbestos increases risk of lung cancer, mesothelioma, and non-malignant respiratory disease. This study evaluated potency and time course effects of LA and positive control amosite (AM) asbestos fibers in male F344 rats following...

  17. Mineral fibre persistence and carcinogenicity.

    Science.gov (United States)

    McDonald, J C

    1998-10-01

    Epidemiological research during the past 40 years has demonstrated with increasing clarity that amphibole asbestos fibres--crocidolite, amosite and tremolite--are more carcinogenic than chrysotile. A smaller number of well-controlled studies using lung burden analyses, while adding to the specificity of this conclusion, have shown that amphibole fibres also differ from chrysotile in being far more durable and biopersistent in lung tissue. Analyses of mesothelioma and lung cancer in a large cohort of Canadian chrysotile miners and millers have recently shown that the low-level presence of fibrous tremolite in these mines, rather than the chrysotile, may well be responsible. The high risk of lung cancer, but not of mesothelioma, in the chrysotile textile industry remains anomalous and cannot be explained in this way. These various findings are directly relevant to the choice of the experimental methods which should be used for screening man-made fibres for industrial use. Although it is clear that biopersistence is a major determinant of cancer risk in animals, and perhaps also in man, other factors affecting the biological activity of mineral fibres may also be important.

  18. Inhaled dust and disease

    Energy Technology Data Exchange (ETDEWEB)

    Holt, P.F.

    1987-01-01

    This book discusses the following: the respiratory system; respirable dust; the fate of inhaled dust; translocation and some general effects of inhaled dust; silicosis; experimental research on silica-related disease; natural fibrous silicates; asbestos dust levels and dust sources; asbestos-related diseases - asbestosis, lung cancer, mesothelioma and other diseases, cancers at sites other than lung and pleura; experimental research relating to asbestos-related diseases; asbestos hazard - mineral types and hazardous occupations, neighbourhood and domestic hazard; silicates other than asbestos-man-made mineral fibres, mineral silicates and cement; metals; coal mine dust, industrial carbon and arsenic; natural and synthetic organic substances; dusts that provoke allergic alveolitis; tobacco smoke.

  19. A comparison of the results from intra-pleural and intra-peritoneal studies with those from inhalation and intratracheal tests for the assessment of pulmonary responses to inhalable dusts and fibres.

    Science.gov (United States)

    Drummond, Gail; Bevan, Ruth; Harrison, Paul

    2016-11-01

    The aim of this paper is to compare results from inhalation studies with those from intraperitoneal and intrapleural tests, where available, for a number of fibrous and particulate test materials. The objective is to determine how well intraperitoneal/intrapleural studies predict the pathological responses observed in more standard in vivo studies of pulmonary toxicity, with a particular focus on carcinogenicity. Published toxicity data was obtained for a number of materials including asbestos, wollastonite, MMVFs (including glass fibres, stone wools and RCF), silicon carbide whiskers, potassium octatitanate, quartz, kevlar, polypropylene and titanium dioxide. For some of the fibrous material reviewed, there is conformity between the results of intraperitoneal and inhalation tests such that they are either consistently positive or consistently negative. For the remaining fibrous materials reviewed, intraperitoneal and inhalation tests give different results, with positive results in the intraperitoneal test not being reflected by positive inhalation results. It is suggested that the intraperitoneal test can be used to exonerate a dust or fibre (because if negative in the intraperitoneal test it is extremely unlikely to be positive in either inhalation or intratracheal tests) but should not be used to positively determine that a dust or fibre is carcinogenic by inhalation. We would argue against the use of intraperitoneal tests for human health risk assessment except perhaps for the purpose of exoneration of a material from classification as a carcinogen.

  20. Induction of nuclear translocation of NF-kappaB in epithelial cells by respirable mineral fibres.

    Science.gov (United States)

    Brown, D M; Beswick, P H; Donaldson, K

    1999-10-01

    A panel of mineral fibres has been studied for their ability to cause translocation of the transcription factor NF-kappaB to the nucleus in A549 lung epithelial cells. On the basis of inhalation studies, three fibres were designated as being carcinogenic-amosite asbestos, silicon carbide and refractory ceramic fibre 1 (RCF1)-or non-carcinogenic-man-made vitreous fibre (MMVF10), Code 100/475 glass fibre, and RCF4. The experiments were carried out at equal fibre number. It was hypothesized that carcinogenic fibres have greater free radical activity than non-carcinogenic fibres and that an oxidative stress produced in the lung after inhalation of fibres could cause translocation of the transcription factor NF-kappaB to the nucleus, where transcription of pro-inflammatory genes such as cytokines could occur. It was demonstrated that a simple oxidant, hydrogen peroxide, caused translocation in a time- and dose-dependent manner. The three carcinogenic fibres produced a significant dose-dependent translocation of NF-kappaB to the nucleus, whereas the non-carcinogenic fibres did not. Silicon carbide fibres were the most potent of the pathogenic fibres. MMVF10 was the most potent of the non-pathogenic fibres, causing significant nuclear translocation of NF-kappaB at high fibre number. Using three antioxidants, curcumin, pyrrolidine dithiocarbamate, and Nacystelin, translocation caused by carcinogenic fibres could be significantly reduced. The present study shows that a short-term in vitro assay can discriminate between pathogenic and non-pathogenic fibres in terms of a key pro-inflammatory event in epithelial cells. The mechanism of the activation of NF-kappaB by pathogenic fibres and its general applicability to other fibre types remain to be determined.

  1. Detection of asbestos fibres in selected building materials

    Directory of Open Access Journals (Sweden)

    Jiří Škvarla

    2009-09-01

    Full Text Available Asbestos is a naturally occurring mineral having a fibrous structure. The Directive 2003/18/EC of the European Parliamentand of the Council of 27 March 2003 considers „asbestos“ the following fibrous silicates: actinolite, gruenerite (amosite, anthophyllite,chrysotile, crocidolite, tremolite.Materials based on asbestos fibres and other mineral fibres have preferential characteristics; they are chemically, electricallyand thermally resistant. Because of these unique characteristics, asbestos is utilized by builders, mainly in roofing, insulation materialsand facades.In connection with the restriction of the usage of asbestos fibres usage in EU is due to the documented carcinogenic impact,it is necessary to detect and identify these fibres.Selected samples of building insulation materials were studied by the polarized light microscopy and by the scanning electronmicroscopy. For the purpose of measuring asbestos, only fibres with a length of more than five micrometers, a breadth of less than threemicrometers and a length/breadth ratio greater than 3:1 were taken into consideration. Asbestos fibres, fibres of mineral wooland cellulose we identified.

  2. Asbestos fibre length-dependent detachment injury to alveolar epithelial cells in vitro: role of a fibronectin-binding receptor.

    Science.gov (United States)

    Donaldson, K.; Miller, B. G.; Sara, E.; Slight, J.; Brown, R. C.

    1993-01-01

    A short and a long fibre sample of amosite asbestos were tested for their effects on cells of the human Type 2 alveolar epithelial cell-line A549 in vitro. The long amosite sample was found to cause a rapid detachment of the epithelial cells live from their substratum. At the highest dose, on average 28% of the cells present were detached in this way. Studies on the mechanism of the detachment injury showed that it did not involve oxidants since it was not ameliorated by scavengers of active oxygen species. Neither was the effect reduced by treatment of the fibres with the iron chelator Desferal. Treatments reported to increase the interaction between fibres and cells, serum and poly-L-lysine, did not influence the detachment injury, nor did lung lining fluid. Conversely, the fibronectin tripeptide RGD alone could cause detachment which suggested that a fibronectin-binding integrin was involved. This receptor could be reduced in activity by long fibre exposure, leading to detachment. The detaching effect of fibre could be mimicked by the protein kinase C activator PMA, and so the second messenger system of the cell could also be involved. This type of injury could be important in the pathology associated with exposure to long fibres. PMID:8392859

  3. In Vitro Dissolution of Libby Amphibole, Amosite Asbestos, and MMVF Using Acid and Synthetic Lung Fluid Media.

    Science.gov (United States)

    Toxicity of inhaled fibers is dependent in part on biopersistence due to changes in size distribution after deposition and clearance in the respiratory tract. To model this in vivo behavior, respirable (PM2.5) Libby amphibole (LA) and amosite asbestos, and a reference material gl...

  4. Mineral fibres: correlation between oxidising surface activity and DNA base hydroxylation.

    Science.gov (United States)

    Nejjari, A; Fournier, J; Pezerat, H; Leanderson, P

    1993-06-01

    In relation to their potential genotoxic properties, the ability of inorganic particles to induce activated species of oxygen with strong oxidative properties can be studied by various methods. In this study the oxidative surface properties of 10 different natural and synthetic mineral fibres were investigated by: (1) an electron paramagnetic resonance technique in which formate was used to trap oxidative species; and (2) a high performance liquid chromatography (HPLC) based method in which deoxyguanosine was used as a trapping agent and the formation of 8-hydroxy-deoxyguanosine (8 OHdG) was analysed. Ground iron-containing fibres such as crocidolite and amosite were the most reactive, whereas fibres without iron--for example, ceramic fibres, xonotlite, and Tismo L--were completely inactive. A good correlation was found when the results from the two methods were compared (r = 0.86).

  5. A risk assessment for exposure to grunerite asbestos (amosite) in an iron ore mine

    Science.gov (United States)

    Nolan, R. P.; Langer, A. M.; Wilson, Richard

    1999-01-01

    The potential for health risks to humans exposed to the asbestos minerals continues to be a public health concern. Although the production and use of the commercial amphibole asbestos minerals—grunerite (amosite) and riebeckite (crocidolite)—have been almost completely eliminated from world commerce, special opportunities for potentially significant exposures remain. Commercially viable deposits of grunerite asbestos are very rare, but it can occur as a gangue mineral in a limited part of a mine otherwise thought asbestos-free. This report describes such a situation, in which a very localized seam of grunerite asbestos was identified in an iron ore mine. The geological occurrence of the seam in the ore body is described, as well as the mineralogical character of the grunerite asbestos. The most relevant epidemiological studies of workers exposed to grunerite asbestos are used to gauge the hazards associated with the inhalation of this fibrous mineral. Both analytical transmission electron microscopy and phase-contrast optical microscopy were used to quantify the fibers present in the air during mining in the area with outcroppings of grunerite asbestos. Analytical transmission electron microscopy and continuous-scan x-ray diffraction were used to determine the type of asbestos fiber present. Knowing the level of the miner’s exposures, we carried out a risk assessment by using a model developed for the Environmental Protection Agency. PMID:10097051

  6. Retention of asbestos fibres in lungs of workers with asbestosis, asbestosis and lung cancer, and mesothelioma in Asbestos township.

    Science.gov (United States)

    Dufresne, A; Bégin, R; Massé, S; Dufresne, C M; Loosereewanich, P; Perrault, G

    1996-01-01

    OBJECTIVE: To conduct a mineralogical study on the particles retained in the necropsied lungs of a homogenous group of asbestos miners and millers from Asbestos township (and a local reference population) and to consider the hypothesis that there is a difference in size between fibres retained in the lungs of patients with asbestosis with and without lung cancer. METHODS: Samples of lung tissue were obtained from 38 patients with asbestosis without lung cancer, 25 with asbestosis and lung cancer, and 12 with mesothelioma, from necropsied Quebec chrysotile miners and millers from Asbestos township. Fibre concentrations in the lungs of these patients were compared with those in tissue from necropsies carried out on a local reference population: men who had died of either accidental death or acute myocardial infarction between 1990 and 1992. 23 were born before 1940 and 26 after 1940. RESULTS: Geometric mean (GM) concentrations were higher in cases than in the controls for chrysotile fibres 5 to 10 microns long in patients with asbestosis with or without lung cancer; for tremolite fibres 5 to 10 microns long in all patients; for crocidolite, talc, or anthophyllite fibres 5 to 10 microns long in patients with mesothelioma; for chrysotile and tremolite fibres > or = 10 microns long in patients with asbestosis; and crocidolite, talc, or anthophyllite fibres > or = 10 microns long in patients with mesothelioma. However, median concentrations of each type of fibre in the lungs did not show any significant differences between the three disease groups. Average length to diameter ratios of the fibres were calculated to be larger in patients with asbestosis and lung cancer than in those without lung cancer for crocidolite fibres > or = 10 microns long, for chrysotile, amosite, and tremolite fibres 5 to 10 microns long, and for chrysotile and crocidolite fibres Asbestos township who had an equal concentration of retained fibres but a tendency to a higher length to diameter

  7. The chemical environment of iron in mineral fibres. A combined X-ray absorption and Mössbauer spectroscopic study.

    Science.gov (United States)

    Pollastri, Simone; D'Acapito, Francesco; Trapananti, Angela; Colantoni, Ivan; Andreozzi, Giovanni B; Gualtieri, Alessandro F

    2015-11-15

    Although asbestos represents today one of the most harmful contaminant on Earth, in 72% of the countries worldwide only amphiboles are banned while controlled use of chrysotile is allowed. Uncertainty on the potential toxicity of chrysotile is due to the fact that the mechanisms by which mineral fibres induces cyto- and geno-toxic damage are still unclear. We have recently started a long term project aimed at the systematic investigation of the crystal-chemistry, bio-interaction and toxicity of the mineral fibres. This work presents a systematic structural investigation of iron in asbestos and erionite (considered the most relevant mineral fibres of social and/or economic-industrial importance) using synchrotron X-ray absorption and Mössbauer spectroscopy. In all investigated mineral fibres, iron in the bulk structure is found in octahedral sites and can be made available at the surface via fibre dissolution. We postulate that the amount of hydroxyl radicals released by the fibers depends, among other factors, upon their dissolution rate; in relation to this, a ranking of ability of asbestos fibres to generate hydroxyl radicals, resulting from available surface iron, is advanced: amosite > crocidolite ≈ chrysotile > anthophyllite > tremolite. Erionite, with a fairly high toxicity potential, contains only octahedrally coordinated Fe(3+). Although it needs further experimental evidence, such available surface iron may be present as oxide nanoparticles coating and can be a direct cause of generation of hydroxyl radicals when such coating dissolves.

  8. Exposure to ceramic man-made mineral fibres.

    Science.gov (United States)

    Friar, J J; Phillips, A M

    1989-01-01

    Ceramic fibres (also known as refractory fibres) are regarded here as man-made mineral fibres (MMMF) capable of withstanding temperatures of 1000-1600 degrees C without appreciable distortion or softening. Ceramic fibres are manufactured largely from the aluminosilicate group of minerals but some contain only alumina, zirconia or silica. Simultaneous personal gravimetric and optical fibre count samples were taken throughout the industry. It has not been possible to correlate gravimetric results with fibre counts in any meaningful way. The general conclusions are as follows: (a) gravimetrically, exposures ranged from less than 1 mg/m3 for light tasks to over 10 mg/m3 for some insulation workers. Exposures above 10 mg/m3 were not necessarily associated with correspondingly high fibre counts; (b) fibre counts rarely exceeded 1 f/ml, and it appears that ceramic fibre materials, in company with other MMMF, do not readily produce high airborne fibre counts; (c) control of dust from mineral wools to 5 mg/m3 achieves control to below 1 f/ml. This relationship does not hold for superfine MMMF and does not always hold for ceramic fibres.

  9. Linear Alkylbenzenesulfonates in indoor Floor Dust

    DEFF Research Database (Denmark)

    Wolkoff, Peder; Madsen, Jørgen Øgaard

    1999-01-01

    The amount of Linear Alkylbenzenesulfonates (LAS) in the particle fraction of floor dust sampled from 7 selected public buildings varied between 34 and 1500 microgram per gram dust, while the contents of the fibre fractions generally were higher with up to 3500 microgram LAS/g dust. The use...... of a cleaning agent with LAS resulted in an increase of the amount of LAS in the floor dust after floor wash relative to just before floor wash. However, the most important source of LAS in the indoor floor dust appears to be residues of detergent in clothing. Thus, a newly washed shirt contained 2960 microgram...

  10. Role of fibre characteristics on cytotoxicity and induction of anaphase/telophase aberrations in rat pleural mesothelial cells in vitro: correlations with in vivo animal findings.

    Science.gov (United States)

    Yegles, M; Janson, X; Dong, H Y; Renier, A; Jaurand, M C

    1995-11-01

    Thirteen samples of natural fibres and five samples of man-made fibres (MMF) were tested to determine their cytotoxicity and ability to produce chromosome missegregation in cultures in rat pleural mesothelial cells (RPMC). The natural samples included attapulgite, two amphiboles (amosite and crocidolite); seven consisted of chrysotile from various origins and three were obtained after chemical treatment of chrysotile. MMF included three refractory ceramic fibres (RCF) and two vitreous fibres (MMVF). All fibre samples were characterized by electron microscopic measurement of the fibre dimensions. Cytotoxicity was assayed on the basis of determination of mitochondrial integrity and chromosome missegregation by light microscopy examination of anaphases/telophases. The carcinogenic potency of 10 natural samples has been previously investigated using intrapleural inoculation in rats. It was therefore possible to establish correlations between in vitro and in vivo data obtained with the same set of samples. The various samples of chrysotile produced different in vitro effects, in agreement with the dispersion of response also observed in vivo. Cytotoxicity appears to be dependent on both fibre length and fibre diameter, as the longest or thickest fibres were the most toxic. The production of abnormal anaphases/telophases appears to depend on the presence of fibres of selected size, such as those previously defined by Stanton et al. (L > 8 micrograms; D < or = 0.25 microns); a threshold values was determined below which no abnormal anaphases/telophases were detected. This non-observable effect level was estimated to be 2.5 x 10(5) 'Stanton' fibres per cm2. There was no correlation between cytotoxicity and mesothelioma induction; in contrast, a correlation was found between the ability of a sample to produce chromosome missegregation in vitro and mesothelioma in vivo.

  11. Effects of high fibre diets on gut fill, behaviour and productivity in broiler breeders

    DEFF Research Database (Denmark)

    Steenfeldt, Sanna; Nielsen, Birte Lindstrøm

    Different types of fibre sources were used in high fibre diets to increase feeding quantity and measure the effect on different parameters in two experiments. In exp. I, three diets (A, commercial control diet; B, high insoluble fibre content; and C, high soluble fibre content) were fed to 10...... significantly more in a hunger test than birds on diets B and C, indicating that these two high-fibre diets did reduce the level of hunger experienced by the birds. Stereotypic pecking was most frequently seen in birds fed A and never observed in birds fed B. Birds on diet C appeared scruffier in their plumage...... fibre feed staying longer in the intestinal system. Birds fed fibre diets displayed more dust bathing and less stereotypic behaviour. Egg production did not differ between the diet treatments. The results from the two experiments show that high fibre diets prolong the passage of feed and reduce...

  12. Mineral fibre problems: a management view.

    Science.gov (United States)

    Hardie, H D

    1980-01-01

    Fibre is a form of matter that imparts exclusive properties to end-products; however, most fibres have been associated with health problems. Although management has a responsibility to ensure the safety of products and processes, data on which to base risk-equation decisions are often inadequate. The limitations of current dust measurement technology suggest that apparently precise numerical exposure data are as subjective as use of the terms 'heavy', 'moderate' or 'light'. Control of any useful but hazardous material is preferable to the ultimate sanction of prohibition. The man-made mineral fibre industry and national and international regulatory agencies should learn from the asbestos industry. It is suggested that a process of consultation, rather than one of confrontation, is more likely to produce widely acceptable solutions in each generation.

  13. Fibre-Optic Gyroscope

    Directory of Open Access Journals (Sweden)

    V. N. Saxena

    1983-04-01

    Full Text Available Comparative study of mechanical, ring-laser and fibre-optic gyroscopes has been made. The single mode fibre-optic gyroscope having a large number of turns of the optical fibre in the spool, replacing He-Ne gas laser by a GaAs laser diode, there by reducing the noise level, and using fully integrated fibre-optics, works out to be the best in the final analysis, for safe navigation and homing of the guided missiles.

  14. The pathological response and fate in the lung and pleura of chrysotile in combination with fine particles compared to amosite asbestos following short-term inhalation exposure: interim results.

    Science.gov (United States)

    Bernstein, D M; Rogers, R A; Sepulveda, R; Donaldson, K; Schuler, D; Gaering, S; Kunzendorf, P; Chevalier, J; Holm, S E

    2010-09-01

    The pathological response and translocation of a commercial chrysotile product similar to that which was used through the mid-1970s in a joint compound intended for sealing the interface between adjacent wall boards was evaluated in comparison to amosite asbestos. This study was unique in that it presents a combined real-world exposure and was the first study to investigate whether there were differences between chrysotile and amosite asbestos fibers in time course, size distribution, and pathological response in the pleural cavity. Rats were exposed by inhalation 6 h/day for 5 days to either sanded joint compound consisting of both chrysotile fibers and sanded joint compound particles (CSP) or amosite asbestos. Subgroups were examined through 1-year postexposure. No pathological response was observed at any time point in the CSP-exposure group. The long chrysotile fibers (L > 20 microm) cleared rapidly (T(1/2) of 4.5 days) and were not observed in the pleural cavity. In contrast, a rapid inflammatory response occurred in the lung following exposure to amosite resulting in Wagner grade 4 interstitial fibrosis within 28 days. Long amosite fibers had a T(1/2) > 1000 days and were observed in the pleural cavity within 7 days postexposure. By 90 days the long amosite fibers were associated with a marked inflammatory response on the parietal pleural. This study provides support that CSP following inhalation would not initiate an inflammatory response in the lung, and that the chrysotile fibers present do not migrate to, or cause an inflammatory response in the pleural cavity, the site of mesothelioma formation.

  15. Microstructured polymer optical fibres

    CERN Document Server

    Large, Maryanne; Barton, Geoff; van Eijkelenborg, Martijn A

    2008-01-01

    Microstructured Polymer Optical Fibres describes the optical properties of microstructured fibres, how they are made and modelled, and outlines some potential applications. These applications include areas where polymer fibres are already used, such as high-data rate transmission for Fibre-to-the Home or within cars, as well as completely new areas such as the photonic bandgap transmission of ""difficult"" wavelengths. Emphasising a conceptual understanding of the underlying physics, Microstructured Polymer Optical Fibres is clearly written, and includes numerous illustrations. It provides an

  16. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end......-directional arrangement. The fibre illumination system comprises a fibre illumination module of the above-mentioned type. By the invention, daylight may be exploited for the illumination of remote interior spaces of buildings in order to save energy, and improve the well-being of users in both housing and working...

  17. Fibres For Sensors

    Science.gov (United States)

    Payne, D. N.

    1984-11-01

    Sensors which rely on the external modulation of the properties of an optical fibre (intrinsic sensors) are receiving much attention since they can be made extremely sensitive, and can be used for distributed measurements. Distributed sensing provides some particularly exciting prospects for acoustic, magnetic and electric field monitoring. To date, however, the great majority of experimental and commercial fibre sensors employ telecommunications-grade fibres, largely as a result of their ready availability. Not only does this policy frequently lead to a design compromise, but in some cases makes the performance marginal or untenable as a result of excessive environmental sensitivity. Despite this, little attention has been given to the design of special sensor fibres with enhanced (or depressed) sensitivity to specific measurands. The position is somewhat better with respect to fibres designed to eliminate sensor polarisation problems (e.g. polar isation-maintaining fibres), but even here further work is required to provide the performance demanded.

  18. [The dust factor in the manufacture of basalt fibers].

    Science.gov (United States)

    Gorban', L N; Riazanov, A V; Voloboeva, A A; Rybak, E A

    1996-01-01

    A study was made of the labour conditions of those workers engaged in the production of basalt fibre (BF). Morphological makeup is examined as is dispersity and cytotoxicity of the dust produced in the process of BF making. An issue is addressed of usefulness of setting special hygienic regulations for BF dust.

  19. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end...... the proximal end of the collection optics into the first end of the input fibre, each collector element having a principal axis for the collection of light defining an optical axis of the collector element. The optical axes of the collector elements are arranged in a radially outward pointing multi...

  20. SALIENT FEATURES OF BAMBOO FIBRE

    Institute of Scientific and Technical Information of China (English)

    Subrata; Das

    2007-01-01

    Bamboo fibre is a regenerated cellulosic fibre produced from bamboo.Starchy pulp is produced from bamboo stems and leaves through a process of alkaline hydrolysis and multi- phase bleaching.Further chemical processes produce bamboo fibre.

  1. SALIENT FEATURES OF BAMBOO FIBRE

    Institute of Scientific and Technical Information of China (English)

    Subrata Das

    2007-01-01

    @@ Bamboo fibre is a regenerated cellulosic fibre produced from bamboo. Starchy pulp is produced from bamboo stems and leaves through a process of alkaline hydrolysis and multiphase bleaching. Further chemical processes produce bamboo fibre.

  2. Fibre reinforced polymer nanocomposites

    NARCIS (Netherlands)

    Vlasveld, D.P.N.

    2005-01-01

    In this thesis the results are described of the research on a combination of two types of composites: thermoplastic nanocomposites and continuous fibre composites. In this three-phase composite the main reinforcing phase are continuous glass or carbon fibres, and the matrix consists of a polyamide 6

  3. POLARISATION PRESERVING OPTICAL FIBRE

    DEFF Research Database (Denmark)

    2000-01-01

    . This cladding structure provides polarisation preserving properties to the optical fibre. Optical fibres using this technology may have claddings with elements placed non-periodically as well as in a two-dimensional periodic lattice - such as cladding providing Photonic Band Gap (PBG) effects....

  4. Chalcogenide Fibre Displacement Sensor

    Science.gov (United States)

    2001-06-01

    Fibre optic technology offers the possibility for developing of a variety of physical sensors for a wide range of physical parameters. The main...integrating sphere. The use of chalcogenide rather quartz fibre optic highly increases the Sensitivity of the sensor. Experimental set-up, transmission characteristics and technical parameters are presented.

  5. Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Sanchez Bjarklev, Araceli

    Photonic crystal fibres represent one of the most active research areas today in the field of optics. The diversity of applications that may be addressed by these fibres and their fundamental appeal, by opening up the possibility of guiding light in a radically new way compared to conventional...... optical fibres, have spun an interest from almost all areas of optics and photonics. The aim of this book is to provide an understanding of the different types of photonic crystal fibres and to outline some of the many new and exciting applications that these fibres offer. The book is intended for both...... readers with a general interest in photonic crystals, as well as for scientists who are entering the field and desire a broad overview as well as a solid starting point for further specialized stuides. Teh book, therefore, covers bothe general aspects such as the link from classical optics to photonic...

  6. Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Sanchez Bjarklev, Araceli

    Photonic crystal fibres represent one of the most active research areas today in the field of optics. The diversity of applications that may be addressed by these fibres and their fundamental appeal, by opening up the possibility of guiding light in a radically new way compared to conventional...... optical fibres, have spun an interest from almost all areas of optics and photonics. The aim of this book is to provide an understanding of the different types of photonic crystal fibres and to outline some of the many new and exciting applications that these fibres offer. The book is intended for both...... readers with a general interest in photonic crystals, as well as for scientists who are entering the field and desire a broad overview as well as a solid starting point for further specialized stuides. Teh book, therefore, covers bothe general aspects such as the link from classical optics to photonic...

  7. On defining dietary fibre.

    Science.gov (United States)

    DeVries, Jonathan W

    2003-02-01

    Establishing a definition for dietary fibre has historically been a balance between nutrition knowledge and analytical method capabilities. While the most widely accepted physiologically-based definitions have generally been accurate in defining the dietary fibre in foods, scientists and regulators have tended, in practice, to rely on analytical procedures as the definitional basis in fact. As a result, incongruities between theory and practice have resulted in confusion regarding the components that make up dietary fibre. In November 1998 the president of the American Association of Cereal Chemists (AACC) appointed an expert scientific review committee and charged it with the task of reviewing and, if necessary, updating the definition of dietary fibre. The committee was further charged with assessing the state of analytical methodology and making recommendations relevant to the updated definition. After due deliberation, an updated definition of dietary fibre was delivered to the AACC Board of Directors for consideration and adoption (Anon, 2000; Jones 2000b). The updated definition includes the same food components as the historical working definition used for approximately 30 years (a very important point, considering that the majority of the research of the past 30 years delineating the positive health effects of dietary fibre is based on that working definition). However, the updated definition more clearly delineates the make-up of dietary fibre and its physiological functionality. As a result, relatively few changes will be necessary in analytical methodology. Current methodologies, in particular AACC-approved method of analysis 32-05 (Grami, 2000), Association of Official Analytical Chemists' official method of analysis 985.29 (Horwitz, 2000a) or AACC 32-07 (Grami, 2000) Association of Official Analytical Chemists 991.43 (Horwitz, 2000a) will continue to be sufficient and used for most foods. A small number of additional methods will be necessary to

  8. Moiré Fibre Bragg Grating Written on Strained Fibres

    Institute of Scientific and Technical Information of China (English)

    孙磊; 冯新焕; 刘艳格; 张伟刚; 袁树忠; 开桂云; 董孝义

    2004-01-01

    Moiré fibre Bragg gratings are made in a single mode fibre and a polarization-maintaining fibre respectively, using an excimer KrF laser and a phase mask. Two gratings are written at the same location of the optical fibre. The wavelength spacing can be finely tuned from 0 to 1.86nm by straining the optical fibre during UV illumination.

  9. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    the proximal end of the collection optics into the first end of the input fibre, each collector element having a principal axis for the collection of light defining an optical axis of the collector element. The optical axes of the collector elements are arranged in a radially outward pointing multi......Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end...... and a second end, and a collection optics, the collection optics being configured to receive light incident on a distal end of the collection optics, to transfer at least partially the incident light to a proximal end of the collection optics, and to couple at least partially the transferred light from...

  10. Allergies, asthma, and dust

    Science.gov (United States)

    Reactive airway disease - dust; Bronchial asthma - dust; Triggers - dust ... Things that make allergies or asthma worse are called triggers. Dust is a common trigger. When your asthma or allergies become worse due to dust, you are ...

  11. [Properties and biological effect of dust of various artificial mineral fibers].

    Science.gov (United States)

    Elovskaja, L T; Werner, I; Kupina, L M; Loscilov, J A; Efremov, L D

    1990-09-01

    Developments and use of man-made mineral fibres are important for the progress in some technical fields. In the last years the number of man-made mineral fibres increased extraordinarily. For the medical evaluation it is necessary to determine the physico-chemical characteristics of the man-made mineral fibre dust and its biological effects in animal experiments. The results of the investigations are described.

  12. Simulation of dust production in ITER transient events

    Energy Technology Data Exchange (ETDEWEB)

    Pestchanyi, S.E. [Forschungszentrum Karlsruhe, Institute for Pulsed Power and Microwave Technology, P.B. 3640, D-76021 Karlsruhe (Germany)], E-mail: sergey.pestchanyi@ihm.fzk.de; Landman, I.S. [Forschungszentrum Karlsruhe, Institute for Pulsed Power and Microwave Technology, P.B. 3640, D-76021 Karlsruhe (Germany)

    2008-12-15

    Dust production from the divertor armour during edge-localised modes (ELMs) has been investigated. Analysis of available experimental data on the dust particle production and the particles distribution on size for the MPG-8 graphite and for NB31 carbon fibre composite (CFC) under the disruption-like surface heat load allowed revealing the unknown mechanical parameters of the NB31 CFC. Using these data the code PEGASUS-3D has been fitted and verified for simulation of the dust production by ELMs. First simulation of the dust production for the ELM of 1 MJ/m{sup 2} heat load and 0.5 ms time duration has been calculated.

  13. Evaluation of occupational gas and dust hazards - abstracts of papers

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    Abstracts of 13 papers are presented. The occupational hazards, generation and harmful effects of toxic gases and vapours are discussed, and the additional risks of fire and explosions encountered with flammable gases are described. Airborne dust (i.e. particulates and fibres capable of entering the respiratory system) and the health effects of these (e.g. pneumoconioses, respiratory tract cancers and allergic alveolitis), with special emphasis on asbestos and other mineral fibres, are considered. The regulations concerning the control of hazardous substances and the practicalities of meeting these are covered, with details of gas detectors, monitoring instruments and sampling techniques. Total, respirable and inhalable dusts are distinguished.

  14. Multibeam Fibre Laser Cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre-laser...... cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

  15. Optical fibre line failure detecting

    OpenAIRE

    Xie, Feng

    2013-01-01

    With the development of modern communications, in order to meet the needs of social development and technological progress the optical fibre communications has become the main communication medium for its high reliability and security. Fibre-optic cable is the channel for signal transmission. It is an important component in the entire fibre-optic network. Once the fibre-optic cable fault happened, the entire communication system would be impacted seriously. When fault occurs, it is important ...

  16. Fibre Optics in Undersea Applications

    Directory of Open Access Journals (Sweden)

    A. K. Talwar

    1984-01-01

    Full Text Available Role of optical fibres for underwater communication cables and hydrophones is discussed. The fibre optics cables provide an excellent solution to the historical bandwidth-diameter problems of conventional coaxial cables.Fibre optic hydrophones are found to have many more advantages apart from high sensitivity and large dynamic range, over the classical sound sensors used in underwater work.

  17. Single-mode optical fibres

    CERN Document Server

    Cancellieri, G

    1991-01-01

    This book describes signal propagation in single-mode optical fibres for telecommunication applications. Such description is based on the analysis of field propagation, considering waveguide properties and also some of the particular characteristics of the material fibre. The book covers such recent advances as, coherent transmissions; optical amplification; MIR fibres; polarization maintaining; polarization diversity and photon counting.

  18. Orientational Distribution of Fibres in Sheared Fibre Suspensions

    Institute of Scientific and Technical Information of China (English)

    KU Xiao-Ke; LIN Jian-Zhong

    2007-01-01

    Motion of fibres in sheared fibre suspensions is simulated numerically by using the lattice Boltzmann method. The orientational distributions of the fibres are presented for different Reynolds numbers, Stokes numbers, shear rate and fibre aspect ratio. Some computational results are compared with the experimental data of pipe Bow, and the qualitative agreement is achieved. The results show that the orientational distributions are greatly affected by the Reynolds numbers, while relatively insensitive to the fibre aspect ratio. The Stokes number and shear rate have obvious influence on the orientation distribution.

  19. Glass Fibre Reinforced Polymers

    NARCIS (Netherlands)

    Nikolaou, N.; Karagianni, L.; Sarakiniatti, M.V.

    2014-01-01

    This "designers' manual" is made during the TIDO-course AR0533 Innovation & Sustainability. Fibre reinforced polymers (FRPs) have been used in many applications over the years, from new construction to retrofitting. They are lightweight, no-corrosive, exhibit high specific strength and specific

  20. Glass Fibre Reinforced Polymers

    NARCIS (Netherlands)

    Nikolaou, N.; Karagianni, L.; Sarakiniatti, M.V.

    2014-01-01

    This "designers' manual" is made during the TIDO-course AR0533 Innovation & Sustainability. Fibre reinforced polymers (FRPs) have been used in many applications over the years, from new construction to retrofitting. They are lightweight, no-corrosive, exhibit high specific strength and specific sti

  1. Modelling of photonic crystal fibres

    DEFF Research Database (Denmark)

    Knudsen, Erik

    2003-01-01

    In the presenta ph.d. work a theoretical study of aspects of modelling photonic crystal fibres was carried out. Photonic crystal fibres form a class of optical waveguides where guidance is no longer provided by a difference in refractive index between core and cladding. Instead, guidance...... is provided by an arrangement of air-holes running along the length of the fibre. Depending on the geometry of the fibre, the guiding mechanism may be either arising from the formation of a photonic bandgap in the cladding structure (photonic bandgap fibre), or by an effect resembling total internal...... modes in contiguous fibre segments curved at different radii. Overall microbend loss is expressed as a statistical mean of mismatch losses. Extending a well proven, established formula for macrobending losses in stop index fibres, we provide an estimate of macrobend losses in an air-guiding photonic...

  2. Dust Mite Allergy

    Science.gov (United States)

    Dust mite allergy Overview By Mayo Clinic Staff Dust mite allergy is an allergic reaction to tiny bugs that commonly live in house dust. Signs of dust mite allergy include those common to hay fever, such as ...

  3. Non-Linear Fibres for Widely Tunable Femtosecond Fibre Lasers

    DEFF Research Database (Denmark)

    Pedersen, Martin Erland Vestergaard

    This Ph.D. thesis investigates how intramodal and intermodal nonlinear processes in few-moded fibres can be used to generate light sources at wavelengths outside the spectral gain-bands of rare-earth-doped opticalfibres. The design of two specialty few-moded fibres for use in a widely tunable...... femtosecond fibre laser is presented. The two fibres are used to facilitate the shifting of a soliton in a cascade configuration from the ytterbium gain-band and to a wavelength of 1280 nm. The temporal pulse duration is on a femtosecond scale with a pulse energy of 5 nJ. The experimentally observed soliton...... self-frequency shift and thereby the outcome of the experimental demonstration of the widely tunable femtosecond fibre laser is shown to depend highly on the chirped of the input pulse into the first few-moded fibre in the cascade setup. Furthermore, an alternative splicing process, with a combination...

  4. Fibre composite in driveline

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, W.

    1989-03-01

    Apart from the geometric degrees of freedom of classical material, fibre composites as material for cardan shafts offer two further free parameters to the design engineer: The fiberment winding angle and the ratio of carbon and glass fibres. This results in a large scope of characteristics in terms of flexibility and torsion. In many cases it is therefore possible to use a one-piece shaft instead of a two-piece shaft, and a specific harmonization of the vibration characteristics of the driveline can be realized. In comparison with shafts made out of steel, mass is reduced by 40-50%, the moment of inertia of the mass by 35-40%. The Composite shaft fulfils the requirements of the performance specifications typical of the components concerned both in terms of engineering and efficiency.

  5. Man-made mineral fibre boards in buildings--health risks caused by quality deficiencies.

    Science.gov (United States)

    Thriene, B; Sobottka, A; Willer, H; Weidhase, J

    1996-11-01

    The Institute of Hygiene was requested to determine causes and scope of health complaints made by the employees of Haldensleben district administration after sound absorbing mineral fibre boards had been installed as suspended ceilings. The boards were coated with a lean water-carried paint; however, the edges, which were partially frayed, were not coated. The air inside the rooms was measured on all four storeys of the building, followed by scanning electron microscopy in compliance with VDI Code 3492. In addition, measurements showed fibres with diameters of > 3 microns which are not subject to the regulations for carcinogenic substances, but, in contrast to the thinner fibres, they may cause irritations of skin and mucosa. The employees were questioned about their health problems. At the beginning of 1994, a total of 79 of the 133 employees complained about itching, reddening and burning of their eyes as well as irritations of the upper respiratory tract. More than 50% had consulted a doctor. Late in 1994, another questionnaire survey was completed. The fibre content of the office air was determined to vary from 1000 to 3500 fibres/m3 and, in addition, 100-200 fibres with diameters of > 3 microns. Our investigations showed that there is an interrelationship between the degree of dust accumulation in the offices and health complaints. Independently of the current discussion of the cancer causing potential of thin man-made mineral fibres, the very long and thick mineral fibres (> 3 microns in diameter) are of topical importance to health.

  6. Optical Fibre Bundle

    CERN Multimedia

    These are sample fibre optic cables which are used for networking. Optical fibers are widely used in fiber-optic communications, where they permit transmission over longer distances and at higher bandwidths (data rates) than wire cables. Fibers are used instead of metal wires because signals travel along them with less loss and are also immune to electromagnetic interference. This is useful for somewhere like CERN where magnets with their highly powerful magnetic fields could pose a problem.

  7. Fibre-optical microendoscopy.

    Science.gov (United States)

    Gu, M; Bao, H; Kang, H

    2014-04-01

    Microendoscopy has been an essential tool in exploring micro/nano mechanisms in vivo due to high-quality imaging performance, compact size and flexible movement. The investigations into optical fibres, micro-scanners and miniature lens have boosted efficiencies of remote light delivery to sample site and signal collection. Given the light interaction with materials in the fluorescence imaging regime, this paper reviews two classes of compact microendoscopy based on a single fibre: linear optical microendoscopy and nonlinear optical microendoscopy. Due to the fact that fluorescence occurs only in the focal volume, nonlinear optical microendoscopy can provide stronger optical sectioning ability than linear optical microendoscopy, and is a good candidate for deep tissue imaging. Moreover, one-photon excited fluorescence microendoscopy as the linear optical microendoscopy suffers from severe photobleaching owing to the linear dependence of photobleaching rate on excitation laser power. On the contrary, nonlinear optical microendoscopy, including two-photon excited fluorescence microendoscopy and second harmonic generation microendoscopy, has the capability to minimize or avoid the photobleaching effect at a high excitation power and generate high image contrast. The combination of various nonlinear signals gained by the nonlinear optical microendoscopy provides a comprehensive insight into biophenomena in internal organs. Fibre-optical microendoscopy overcomes physical limitations of traditional microscopy and opens up a new path to achieve early cancer diagnosis and microsurgery in a minimally invasive and localized manner.

  8. Analysis of glass fibre sizing

    DEFF Research Database (Denmark)

    Petersen, Helga Nørgaard; Kusano, Yukihiro; Brøndsted, Povl

    2014-01-01

    Glass fibre reinforced polymer composites are widely used for industrial and engineering applications which include construction, aerospace, automotive and wind energy industry. During the manufacturing glass fibres, they are surface-treated with an aqueous solution. This process and the treated...... surfaces are called sizing. The sizing influences the properties of the interface between fibres and a matrix, and subsequently affects mechanical properties of composites. In this work the sizing of commercially available glass fibres was analysed so as to study the composition and chemical structures....... Soxhlet extraction was used to extract components of the sizing from the glass fibres. The glass fibres, their extracts and coated glass plates were analysed by Thermo-Gravimetric Analysis combined with a mass spectrometer (TGA-MS), and Attenuated Total Reflectance Fourier Transform Infrared (ATR...

  9. Carcinogenicity studies on natural and man-made fibres with the intraperitoneal test in rats.

    Science.gov (United States)

    Pott, F; Roller, M; Ziem, U; Reiffer, F J; Bellmann, B; Rosenbruch, M; Huth, F

    1989-01-01

    Female Wistar rats were injected intraperitoneally (i.p.) with a suspension of 11 fibrous and 3 granular dusts. A dose of 0.25 mg actinolite or UICC chrysotile induced tumours of the peritoneum in more than 50% of the animals. Even 0.05 and 0.01 mg proved to be carcinogenic, although no adhesions of the abdominal organs could be observed. The findings are in conflict with the hypothesis that a scar is always the morphological precondition for the development of an asbestos-induced tumour. Actinolite injected i.p. in a solution of polyvinylpyridine-N-oxide gave a lower tumour incidence than when suspended only in saline, possibly due to inactivation of the fibre surface. Persistent glass fibres were less effective than actinolite having a similar fibre size distribution. On the other hand, relatively thick basalt fibres and ceramic fibres gave higher tumour incidences than expected. Wollastonite fibres were not carcinogenic, probably because of their low durability. Large amounts of polyvinylchloride, alpha-ferric oxide hydrate and wood dust also led only to adhesions of the abdominal organs and fibrosis; a definite carcinogenic effect was not detected.

  10. [Exposure to ceramic fibers in the work environment. II. Occupational exposure to dust in plants producing ceramic fiber; fibrogenic effect of the fibers].

    Science.gov (United States)

    Wojtczak, J; Lao, I; Krajnow, A

    1996-01-01

    The aim of the work was to assess the exposure to dust containing ceramic fibres among workers employed in the plant producing aluminosilicate fibres, and to investigate fibrogenic properties of produced ceramic aluminosilicate fibres (L-1). The studies carried out in the work environment revealed that workers were exposed to dust containing respirable fibres from materials produced (fibres, mats). Mean concentrations of these fibres ranged from 0.07 to 0.37 f/cm3 and they were considerably lower than MAC value (1 f/cm3) proposed for respirable ceramic fibres. Mean total dust concentrations ranged from 0.4 to 2.9 mg/m3, and at two working posts they exceeded the proposed MAC value (2 mg/m3). In animal experiments (Wistar female rats) a single dose (25 mg) of L-1 fibres administered intratracheally induced pathological symptoms in lungs, limited to reactive changes in the form of granuloma with weakly pronounced cytolysis, and mean levels of hydroxyproline in the lungs did not differ significantly from the physiological level. The L-1 fibre was classified in the group of dusts with insignificant fibrogenic effects.

  11. Applications for carbon fibre recovered from composites

    Science.gov (United States)

    Pickering; Liu, Z.; Turner, TA; Wong, KH

    2016-07-01

    Commercial operations to recover carbon fibre from waste composites are now developing and as more recovered fibre becomes available new applications for recovered fibre are required. Opportunities to use recovered carbon fibre as a structural reinforcement are considered involving the use of wet lay processes to produce nonwoven mats. Mats with random in-plane fibre orientation can readily be produced using existing commercial processes. However, the fibre volume fraction, and hence the mechanical properties that can be achieved, result in composites with limited mechanical properties. Fibre volume fractions of 40% can be achieved with high moulding pressures of over 100 bar, however, moulding at these pressures results in substantial fibre breakage which reduces the mean fibre length and the properties of the composite manufactured. Nonwoven mats made from aligned, short carbon fibres can achieve higher fibre volume fractions with lower fibre breakage even at high moulding pressure. A process for aligning short fibres is described and a composite of over 60% fibre volume fraction has been manufactured at a pressures up to 100 bar with low fibre breakage. Further developments of the alignment process have been undertaken and a composite of 46% fibre volume fraction has been produced moulded at a pressure of 7 bar in an autoclave, exhibiting good mechanical properties that compete with higher grade materials. This demonstrates the potential for high value applications for recovered carbon fibre by fibre alignment.

  12. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    DEFF Research Database (Denmark)

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage...... obtained by steam explosion of hemp fibres prior defibrated with pectin degrading enzymes. The S2 layer in the fibre wall of the hemp fibres consisted of1-4 cellulose rich and lignin poor concentric layers constructed of ca. 100 nm thick lamellae. The microfibril angle showed values in the range 0......-10° for the main part of the S2-layer and 70-90° for the S1-layer. The microfibrils that are mainly parallelwith the fibre axis explain the high fibre stiffness, which in defibrated hemp fibres reached 94 GPa. The defibrated hemp fibres had higher fibre stiffness (88-94 GPa) than hemp yarn (60 GPa), which...

  13. Microstructured Optical Fibres

    DEFF Research Database (Denmark)

    1999-01-01

    complete PBGs, which reflects light incident from air or vacuum. Such structures may be used as cladding structures in optical fibres, where light is confined and thereby guided in a hollow core region. In addition, the present invention relates to designs for ultra low-loss PBG waveguiding structures......The present invention relates to a new class of optical waveguides, in which waveguiding along one or more core regions is obtained through the application of the Photonic Bandgap (PBG) effect. The invention further relates to optimised two-dimensional lattice structures capable of providing...

  14. Design of DFB fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Povlsen, Jørn Hedegaard; Varming, Poul

    1998-01-01

    A numerical model for erbium distributed feedback (DFB) fibre lasers is presented. The model is used to optimise the location of a discrete phase-shift to obtain maximum output power. For DFB fibre lasers of up to 10cm in length it is shown that the influence of Kerr nonlinearity with respect...

  15. Products based on the mixes of fly ashes and fibre sludge (fibre-ashes) for road construction; Produkter baserade paa blandningar av flygaska och fiberslam (fiberaskor) foer vaegbyggande

    Energy Technology Data Exchange (ETDEWEB)

    Lahtinen, Pentti; Maijala Aino; Macsik, Josef

    2005-03-01

    economically potential fibre-ash mixtures and recommendations for their further development with the help of field tests and test construction. The most noteworthy benefits of the fibre ashes as soil construction materials are their elasticity and resistance against permanent deformation. These properties make the fibre-ash materials significantly more frost resistant than the conventional materials. Also, the fibre-ashes are easier and simpler to use in the construction process than the fly ashes because the fibre-ashes are practically dust-tight materials. The results of the project will be background information for the further studies, and for the guidelines and commercialisation of e.g. road construction with fibre ashes.

  16. Reticulation des fibres lignocellulosiques

    Science.gov (United States)

    Landrevy, Christel

    Pour faire face à la crise économique la conception de papier à valeur ajoutée est développée par les industries papetières. Le but de se projet est l'amélioration des techniques actuelles de réticulation des fibres lignocellulosiques de la pâte à papier visant à produire un papier plus résistant. En effet, lors des réactions de réticulation traditionnelles, de nombreuses liaisons intra-fibres se forment ce qui affecte négativement l'amélioration anticipée des propriétés physiques du papier ou du matériau produit. Pour éviter la formation de ces liaisons intra-fibres, un greffage sur les fibres de groupements ne pouvant pas réagir entre eux est nécessaire. La réticulation des fibres par une réaction de « click chemistry » appelée cycloaddition de Huisgen entre un azide et un alcyne vrai, catalysée par du cuivre (CuAAC) a été l'une des solutions trouvée pour remédier à ce problème. De plus, une adaptation de cette réaction en milieux aqueux pourrait favoriser son utilisation en milieu industriel. L'étude que nous désirons entreprendre lors de ce projet vise à optimiser la réaction de CuAAC et les réactions intermédiaires (propargylation, tosylation et azidation) sur la pâte kraft, en milieu aqueux. Pour cela, les réactions ont été adaptées en milieu aqueux sur la cellulose microcristalline afin de vérifier sa faisabilité, puis transférée à la pâte kraft et l'influence de différents paramètres comme le temps de réaction ou la quantité de réactifs utilisée a été étudiée. Dans un second temps, une étude des différentes propriétés conférées au papier par les réactions a été réalisée à partir d'une série de tests papetiers optiques et physiques. Mots Clés Click chemistry, Huisgen, CuAAC, propargylation, tosylation, azidation, cellulose, pâte kraft, milieu aqueux, papier.

  17. Random distributed feedback fibre lasers

    Science.gov (United States)

    Turitsyn, Sergei K.; Babin, Sergey A.; Churkin, Dmitry V.; Vatnik, Ilya D.; Nikulin, Maxim; Podivilov, Evgenii V.

    2014-09-01

    The concept of random lasers exploiting multiple scattering of photons in an amplifying disordered medium in order to generate coherent light without a traditional laser resonator has attracted a great deal of attention in recent years. This research area lies at the interface of the fundamental theory of disordered systems and laser science. The idea was originally proposed in the context of astrophysics in the 1960s by V.S. Letokhov, who studied scattering with “negative absorption” of the interstellar molecular clouds. Research on random lasers has since developed into a mature experimental and theoretical field. A simple design of such lasers would be promising for potential applications. However, in traditional random lasers the properties of the output radiation are typically characterized by complex features in the spatial, spectral and time domains, making them less attractive than standard laser systems in terms of practical applications. Recently, an interesting and novel type of one-dimensional random laser that operates in a conventional telecommunication fibre without any pre-designed resonator mirrors-random distributed feedback fibre laser-was demonstrated. The positive feedback required for laser generation in random fibre lasers is provided by the Rayleigh scattering from the inhomogeneities of the refractive index that are naturally present in silica glass. In the proposed laser concept, the randomly backscattered light is amplified through the Raman effect, providing distributed gain over distances up to 100 km. Although an effective reflection due to the Rayleigh scattering is extremely small (˜0.1%), the lasing threshold may be exceeded when a sufficiently large distributed Raman gain is provided. Such a random distributed feedback fibre laser has a number of interesting and attractive features. The fibre waveguide geometry provides transverse confinement, and effectively one-dimensional random distributed feedback leads to the generation

  18. Random distributed feedback fibre lasers

    Energy Technology Data Exchange (ETDEWEB)

    Turitsyn, Sergei K., E-mail: s.k.turitsyn@aston.ac.uk [Aston Institute of Photonic Technologies, Aston University, Birmingham B4 7ET (United Kingdom); Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Babin, Sergey A. [Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Churkin, Dmitry V. [Aston Institute of Photonic Technologies, Aston University, Birmingham B4 7ET (United Kingdom); Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Vatnik, Ilya D.; Nikulin, Maxim [Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Podivilov, Evgenii V. [Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation)

    2014-09-10

    The concept of random lasers exploiting multiple scattering of photons in an amplifying disordered medium in order to generate coherent light without a traditional laser resonator has attracted a great deal of attention in recent years. This research area lies at the interface of the fundamental theory of disordered systems and laser science. The idea was originally proposed in the context of astrophysics in the 1960s by V.S. Letokhov, who studied scattering with “negative absorption” of the interstellar molecular clouds. Research on random lasers has since developed into a mature experimental and theoretical field. A simple design of such lasers would be promising for potential applications. However, in traditional random lasers the properties of the output radiation are typically characterized by complex features in the spatial, spectral and time domains, making them less attractive than standard laser systems in terms of practical applications. Recently, an interesting and novel type of one-dimensional random laser that operates in a conventional telecommunication fibre without any pre-designed resonator mirrors–random distributed feedback fibre laser–was demonstrated. The positive feedback required for laser generation in random fibre lasers is provided by the Rayleigh scattering from the inhomogeneities of the refractive index that are naturally present in silica glass. In the proposed laser concept, the randomly backscattered light is amplified through the Raman effect, providing distributed gain over distances up to 100 km. Although an effective reflection due to the Rayleigh scattering is extremely small (∼0.1%), the lasing threshold may be exceeded when a sufficiently large distributed Raman gain is provided. Such a random distributed feedback fibre laser has a number of interesting and attractive features. The fibre waveguide geometry provides transverse confinement, and effectively one-dimensional random distributed feedback leads to the

  19. Tapered optical fibres for sensing

    Science.gov (United States)

    Martan, Tomas; Kanka, Jiri; Kasik, Ivan; Matejec, Vlastimil

    2008-11-01

    Recently, optical fibre tapers have intensively been investigated for many applications e.g. in telecommunications, medicine and (bio-) chemical sensing. The paper deals with enhancement of evanescent-field sensitivity of the solid-core microstructured fibre with steering-wheel air-cladding. Enhancement of a performance of the microstructured fibre is based on reduction of fibre core diameter down to narrow filament by tapering thereby defined part of light power is guided by an evanescent wave traveling in axial cladding air holes. The original fibre structure with outer diameter of 125 µm was reduced 2×, 2.5×, 3.33×, and 4× for increasing relatively small intensity overlap of guided core mode at wavelength of 1.55 μm with axial air holes. The inner structures of tapered microstructured fibre with steering-wheel aircladding were numerically analyzed and mode intensity distributions were calculated using the FDTD technique. Analyzed fiber tapers were prepared by constructed fibre puller employing 'flame brush technique'.

  20. Helically twisted photonic crystal fibres.

    Science.gov (United States)

    Russell, P St J; Beravat, R; Wong, G K L

    2017-02-28

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic 'space', cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of 'numerical experiments' based on finite-element solutions of Maxwell's equations in a helicoidal frame.This article is part of the themed issue 'Optical orbital angular momentum'. © 2017 The Authors.

  1. Helically twisted photonic crystal fibres

    Science.gov (United States)

    Russell, P. St. J.; Beravat, R.; Wong, G. K. L.

    2017-02-01

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic `space', cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of `numerical experiments' based on finite-element solutions of Maxwell's equations in a helicoidal frame. This article is part of the themed issue 'Optical orbital angular momentum'.

  2. Wetting of flexible fibre arrays.

    Science.gov (United States)

    Duprat, C; Protière, S; Beebe, A Y; Stone, H A

    2012-02-23

    Fibrous media are functional and versatile materials, as demonstrated by their ubiquity both in natural systems such as feathers and adhesive pads and in engineered systems from nanotextured surfaces to textile products, where they offer benefits in filtration, insulation, wetting and colouring. The elasticity and high aspect ratios of the fibres allow deformation under capillary forces, which cause mechanical damage, matting self-assembly or colour changes, with many industrial and ecological consequences. Attempts to understand these systems have mostly focused on the wetting of rigid fibres or on elastocapillary effects in planar geometries and on a fibre brush withdrawn from an infinite bath. Here we consider the frequently encountered case of a liquid drop deposited on a flexible fibre array and show that flexibility, fibre geometry and drop volume are the crucial parameters that are necessary to understand the various observations referred to above. We identify the conditions required for a drop to remain compact with minimal spreading or to cause a pair of elastic fibres to coalesce. We find that there is a critical volume of liquid, and, hence, a critical drop size, above which this coalescence does not occur. We also identify a drop size that maximizes liquid capture. For both wetting and deformation of the substrates, we present rules that are deduced from the geometric and material properties of the fibres and the volume of the drop. These ideas are applicable to a wide range of fibrous materials, as we illustrate with examples for feathers, beetle tarsi, sprays and microfabricated systems.

  3. Helically twisted photonic crystal fibres

    Science.gov (United States)

    Beravat, R.; Wong, G. K. L.

    2017-01-01

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic ‘space’, cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of ‘numerical experiments’ based on finite-element solutions of Maxwell's equations in a helicoidal frame. This article is part of the themed issue ‘Optical orbital angular momentum’. PMID:28069771

  4. [Small fibre neuropathy: knowledge is power].

    NARCIS (Netherlands)

    Hoeijmakers, J.G.; Bakkers, M.; Blom, E.W.; Drenth, J.P.H.; Merkies, I.S.; Faber, C.G.

    2012-01-01

    Small fibre neuropathy is a neuropathy of the small non-myelinated C-fibres and myelinated Adelta-fibres. Clinically, an isolated small fibre neuropathy is distinguished by sensory and autonomic symptoms, with practically no abnormalities on neurological examination other than possible distorted pai

  5. Dispersion properties of photonic crystal fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Dridi, Kim;

    1998-01-01

    Approximate dispersion and bending properties of all-silica two-dimensional photonic crystal fibres are characterised by the combination of an effective-index model and classical analysis tools for optical fibres. We believe for the first time to have predicted the dispersion properties of photonic...... crystal fibres. The results strongly indicate that these fibres have potential applications as dispersion managing components...

  6. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    OpenAIRE

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage is unavoidable. The mild defibration was performed by degradation of the pectin and lignin rich middle lamellae around the fibres by cultivation of the mutated white rot fungus Phlebia radiata Cel 26. Fibr...

  7. Periodic Structures in Optical Fibres.

    Science.gov (United States)

    Hand, Duncan Paul

    1990-01-01

    Available from UMI in association with The British Library. The work presented in this thesis concerns techniques for the formation of periodic structures in optical fibres. Two different methods of producing such structures are studied in detail. The first of these involves a breakdown mechanism (known as the 'fibre fuse') that permanently damages the core glass in a periodic manner leaving it unable to guide light. The dynamics of this mechanism are studied, with a view to controlling it for the production of interactive grating structures. It is determined that, due to a sharp rise in fibre absorption with temperature, a thermal shock -wave, with a typical thermal gradient of several hundred degrees Kelvin per micron, forms and travels along the fibre, heating the core glass to such an extent that damage occurs. The periodicity of the resultant damage arises from thermal focusing and defocusing of light in the region of this shock-wave. The second method makes use of the photorefractivity observed in certain germanosilicate fibres on exposure to moderate intensity blue light of wavelength ~480nm or UV light ~240nm. A single-mode fibre transmission filter is demonstrated for the first time, produced by exposing a fibre Sagnac loop mirror to 488nm holographic fringes. Average index changes are shown to occur if such fibres are exposed to spatially uniform blue or UV light, indicating that grating formation is by a different mechanism to the local charge separation which occurs in photorefractive crystals. The various characteristics of these average index changes are measured and analysed, with the conclusion that they result from defect centre formation, driven by two photon absorption with blue light, or single photon absorption with UV light. Associated birefringence changes are also measured and are exploited in a hi-bi fibre to periodically perturb the birefringence axes, producing a narrow-line transmission filter.

  8. Resonance modes in optical fibres

    Institute of Scientific and Technical Information of China (English)

    余寿绵; 余恬

    2002-01-01

    The weakly nonlinear boundary value problem of wave propagation in an optical fibre (for the transverse electric mode, for example) is formulated and a modified linear solution is obtained. It is shown that a self-consistent theory of fibre optics should be weakly nonlinear. The mode of critical refraction that does not exist in the linear theory is obtained, showing that it is a mode consisting of resonance modes. It is shown that the signal carriers in a long fibre are of resonance modes, not normal modes. Some experimental data are given for comparison with the theoretical predictions, and the agreement seems satisfactory.

  9. Comparative study of lung functions in women working in different fibre industries.

    Science.gov (United States)

    Khanam, F; Islam, N; Hai, M A

    2008-07-01

    A cross sectional work has been done on Bangladeshi females, working in different fibre industries, to study the effect of exposure to fibre dust on pulmonary functions. The ventilatory capacities were measured by VMI ventilometer in 653 apparently healthy women (160, 162 and 167 were jute, textile and garment industry workers, respectively). For the controls 164 females were recruited who never worked in any fibre industry. The observed FVC, FEV1 and PEFR were lower in all groups of fibre industry workers than those of the control. Among the industry workers, the jute mill workers had the lowest ventilatory capacities and garment industry workers had the highest values. The jute and textile mill workers had also significantly lower FEV1 and PEFR than those of garment industry workers. The FEV1 and PEFR were significantly lower in jute mill workers than those of textile ill workers. The low ventilatory capacities were almost proportionate with the length of service of the workers. Thus, the present study indicates that the fibre dust, on regular exposure for longer duration, may limit the lung functions.

  10. Intrafusal muscle fibre types in frog spindles.

    Science.gov (United States)

    Diwan, F H; Ito, F

    1989-04-01

    Muscle spindles from bullfrog semitendinosus, iliofibularis and sartorius muscles were examined with light and electron microscopy. Four types of intrafusal muscle fibre were identified according to their diameter, central nucleation and reticular zone arrangement: a large nuclear bag fibre, a medium nuclear bag fibre, and two types of small nuclear chain fibres with and without a reticular zone, respectively. It is suggested that they are comparable to the nuclear bag1, bag2 and chain fibres in mammalian muscle spindles.

  11. Intrafusal muscle fibre types in frog spindles.

    OpenAIRE

    Diwan, F H; Ito, F

    1989-01-01

    Muscle spindles from bullfrog semitendinosus, iliofibularis and sartorius muscles were examined with light and electron microscopy. Four types of intrafusal muscle fibre were identified according to their diameter, central nucleation and reticular zone arrangement: a large nuclear bag fibre, a medium nuclear bag fibre, and two types of small nuclear chain fibres with and without a reticular zone, respectively. It is suggested that they are comparable to the nuclear bag1, bag2 and chain fibres...

  12. Role of cellulose in wood dust-induced fibrosing alveo-bronchiolitis in rat.

    Science.gov (United States)

    Tátrai, E; Adamis, Z; Böhm, U; Merétey, K; Ungváry, G

    1995-01-01

    Our experiments suggest that in the development of plant dust-induced fibrosing alveobronchiolitis--Scadding's fibrosing alveolitis--the cellulose content of plant dusts has a decisive aetiological role. Namely, the wood dust (pine) and the cellulose induced morphologically identical granulomatous inflammation and fibrosis, whereas the fibre-free extract of wood dust did not cause pathological changes in the lungs. The induction of H2O2 and superoxide anion production, shown in vitro in leucocytes, probably has an important role in the development of fibrosis.

  13. Dust Measurements in Tokamaks

    Energy Technology Data Exchange (ETDEWEB)

    Rudakov, D; Yu, J; Boedo, J; Hollmann, E; Krasheninnikov, S; Moyer, R; Muller, S; Yu, A; Rosenberg, M; Smirnov, R; West, W; Boivin, R; Bray, B; Brooks, N; Hyatt, A; Wong, C; Fenstermacher, M; Groth, M; Lasnier, C; McLean, A; Stangeby, P; Ratynskaia, S; Roquemore, A; Skinner, C; Solomon, W M

    2008-04-23

    Dust production and accumulation impose safety and operational concerns for ITER. Diagnostics to monitor dust levels in the plasma as well as in-vessel dust inventory are currently being tested in a few tokamaks. Dust accumulation in ITER is likely to occur in hidden areas, e.g. between tiles and under divertor baffles. A novel electrostatic dust detector for monitoring dust in these regions has been developed and tested at PPPL. In DIII-D tokamak dust diagnostics include Mie scattering from Nd:YAG lasers, visible imaging, and spectroscopy. Laser scattering resolves size of particles between 0.16-1.6 {micro}m in diameter; the total dust content in the edge plasmas and trends in the dust production rates within this size range have been established. Individual dust particles are observed by visible imaging using fast-framing cameras, detecting dust particles of a few microns in diameter and larger. Dust velocities and trajectories can be determined in 2D with a single camera or 3D using multiple cameras, but determination of particle size is problematic. In order to calibrate diagnostics and benchmark dust dynamics modeling, pre-characterized carbon dust has been injected into the lower divertor of DIII-D. Injected dust is seen by cameras, and spectroscopic diagnostics observe an increase of carbon atomic, C2 dimer, and thermal continuum emissions from the injected dust. The latter observation can be used in the design of novel dust survey diagnostics.

  14. Levels of airborne man-made mineral fibres in U.K. dwellings. I—Fibre levels during and after installation of insulation

    Science.gov (United States)

    Jaffrey, Taqi S. A. M.

    This paper gives the details of airborne levels of man-made mineral fibres (MMMF) found during installation of loft insulation in 12 dwellings. About 250 samples of air were collected and analyzed by transmission electron microscopy (TEM). Respirable fibre levels measured in static samples collected in the lofts during installation generally were fibre levels werefibre blanket. A few selected samples were also analyzed by phase contrast optical microscopy (PCOM) which showed lower values than those recorded by TEM. Static gravimetric concentrations in the lofts were in the 0.3-6.5 mg m -3 range, and in the living spaces 0.11-0.44 mg m -3, but in both environments most of this dust was not MMMF.

  15. Extreme Silica Optical Fibre Gratings

    Directory of Open Access Journals (Sweden)

    Kevin Cook

    2008-10-01

    Full Text Available A regenerated optical fibre Bragg grating that survives temperature cycling up to 1,295°C is demonstrated. A model based on seeded crystallisation or amorphisation is proposed.

  16. Current status of natural fibres

    CSIR Research Space (South Africa)

    Anandjiwala, RD

    2006-12-01

    Full Text Available , automotive, aerospace, marine, electronic, leisure and household uses. This paper will provide an overview of the current status of research and development. It will also deal with future drivers for the growth and competitiveness of natural fibres...

  17. Natural Fibre-Reinforced Biofoams

    Directory of Open Access Journals (Sweden)

    Anne Bergeret

    2011-01-01

    Full Text Available Starches and polylactic acids (PLAs represent the main biobased and biodegradable polymers with potential industrial availability in the next decades for “bio” foams applications. This paper investigates the improvement of their morphology and properties through processing and materials parameters. Starch foams were obtained by melt extrusion in which water is used as blowing agent. The incorporation of natural fibres (hemp, cellulose, cotton linter, sugarcane, coconut in the starch foam induced a density reduction up to 33%, a decrease in water absorption, and an increase in mechanical properties according to the fibre content and nature. PLA foams were obtained through single-screw extrusion using of a chemical blowing agent that decomposed at the PLA melting temperature. A void content of 48% for PLA and 25% for cellulose fibre-reinforced PLA foams and an improvement in mechanical properties were achieved. The influence of a fibre surface treatment was investigated for both foams.

  18. Modeling of photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Barkou, Stig Eigil

    1999-01-01

    Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated.......Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated....

  19. Connectorization of fibre Bragg grating sensors recorded in microstructured polymer optical fibre

    DEFF Research Database (Denmark)

    Abang, A.; Saez-Rodriguez, D.; Nielsen, Kristian

    2013-01-01

    We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate).......We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate)....

  20. Association of man-made mineral fibre exposure and sarcoidlike granulomas.

    Science.gov (United States)

    Drent, M; Bomans, P H; Van Suylen, R J; Lamers, R J; Bast, A; Wouters, E F

    2000-08-01

    It is assumed that sarcoidosis is caused by inhalation of air borne agents in susceptible persons triggering the inflammatory reaction. The association of metallic dust exposure, such as beryllium and aluminium, and sarcoidlike pulmonary disorders is well known. The ability of man-made mineral fibres (MMMF) to cause granulomatous lung disease has not been appreciated until now. Recently, we observed the association of sarcoidlike granulomatous reaction and occupational history of glass fibre exposure. We hypothesized that there might be a relationship between MMMF exposure and the development of sarcoidlike granulomas. Therefore, the records of 50 sarcoidosis patients-who visited our outpatient clinic between 1996 and 1999 were reviewed. This revealed that 14 cases recalled a history of exposure to either glass fibres or rock wool, both MMMF fibres. The available obtained tissue specimens (n = 12) were reviewed. In six cases electron microscopy qualitative analysis of small fragments of the tissue revealed among others silica, aluminium and sometimes titanium. A distinct relation between fibre deposits fibre deposits and granulomas was found. These findings indicate that in susceptible people MMMF exposure might be related to a chronic granulomatous disease similar to chronic beryllium disease.

  1. Precision single mode fibre integral field spectroscopy with the RHEA spectrograph

    Science.gov (United States)

    Rains, Adam D.; Ireland, Michael J.; Jovanovic, Nemanja; Feger, Tobias; Bento, Joao; Schwab, Christian; Coutts, David W.; Guyon, Olivier; Arriola, Alexander; Gross, Simon

    2016-08-01

    The RHEA Spectrograph is a single-mode echelle spectrograph designed to be a replicable and cost effective method of undertaking precision radial velocity measurements. Two versions of RHEA currently exist, one located at the Australian National University in Canberra, Australia (450 - 600nm wavelength range), and another located at the Subaru Telescope in Hawaii, USA (600 - 800 nm wavelength range). Both instruments have a novel fibre feed consisting of an integral field unit injecting light into a 2D grid of single mode fibres. This grid of fibres is then reformatted into a 1D array at the input of the spectrograph (consisting of the science fibres and a reference fibre capable of receiving a white-light or xenon reference source for simultaneous calibration). The use of single mode fibres frees RHEA from the issue of modal noise and significantly reduces the size of the optics used. In addition to increasing the overall light throughput of the system, the integral field unit allows for cutting edge science goals to be achieved when operating behind the 8.2m Subaru Telescope and the SCExAO adaptive optics system. These include, but are not limited to: resolved stellar photospheres; resolved protoplanetary disk structures; resolved Mira shocks, dust and winds; and sub-arcsecond companions. We present details and results of early tests of RHEA@Subaru and progress towards the stated science goals.

  2. Strength of Concrete Containing Basalt Fibre

    Directory of Open Access Journals (Sweden)

    Parvez Imraan Ansari

    2015-04-01

    Full Text Available This paper presents the comparative study of effect of basalt fibre on compressive and split tensile strength of M40 grade concrete. The basalt fibre was mixed in concrete by (0.5%, 1%, and 1.5% of its total weight of cement in concrete. Results indicated that the strength increases with increase of basalt fibre content up to 1.0% beyond that there is a reduction in strength on increasing basalt fibre. The results show that the concrete specimen with 1.0% of basalt fibre gives better performance when it compared with 0.5%and 1.5% basalt fibre mix in concrete specimens.

  3. Practical Hydrogen Loading of Air Silica Fibres

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Jensen, Jesper Bevensee; Jensen, Jesper Bo Damm

    2005-01-01

    A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown.......A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown....

  4. Carbon nanotubes for ultrafast fibre lasers

    Directory of Open Access Journals (Sweden)

    Chernysheva Maria

    2017-01-01

    Full Text Available Carbon nanotubes (CNTs possess both remarkable optical properties and high potential for integration in various photonic devices. We overview, here, recent progress in CNT applications in fibre optics putting particular emphasis on fibre lasers. We discuss fabrication and characterisation of different CNTs, development of CNT-based saturable absorbers (CNT-SA, their integration and operation in fibre laser cavities putting emphasis on state-of-the-art fibre lasers, mode locked using CNT-SA. We discuss new design concepts of high-performance ultrafast operation fibre lasers covering ytterbium (Yb, bismuth (Bi, erbium (Er, thulium (Tm and holmium (Ho-doped fibre lasers.

  5. Carbon nanotubes for ultrafast fibre lasers

    Science.gov (United States)

    Chernysheva, Maria; Rozhin, Aleksey; Fedotov, Yuri; Mou, Chengbo; Arif, Raz; Kobtsev, Sergey M.; Dianov, Evgeny M.; Turitsyn, Sergei K.

    2017-01-01

    Carbon nanotubes (CNTs) possess both remarkable optical properties and high potential for integration in various photonic devices. We overview, here, recent progress in CNT applications in fibre optics putting particular emphasis on fibre lasers. We discuss fabrication and characterisation of different CNTs, development of CNT-based saturable absorbers (CNT-SA), their integration and operation in fibre laser cavities putting emphasis on state-of-the-art fibre lasers, mode locked using CNT-SA. We discuss new design concepts of high-performance ultrafast operation fibre lasers covering ytterbium (Yb), bismuth (Bi), erbium (Er), thulium (Tm) and holmium (Ho)-doped fibre lasers.

  6. Dust removal and filter technology. Entstaubungs- und Filtertechnik

    Energy Technology Data Exchange (ETDEWEB)

    Stockmann, H.W. (DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany). DMT-Institut fuer Staubbekaempfung, Gefahrstoffe und Ergonomie); Henke, B. (DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany). DMT-Institut fuer Staubbekaempfung, Gefahrstoffe und Ergonomie)

    1991-01-01

    New approaches were adopted in filter technology to respond to technological changes in mechanized mining and to allow perfect dust removal in keeping with occupational hygiene requirements. Self-supporting filter materials based on ceramic fibres and synthetic granulates were taken to develop filter elements allowing lamination to enhance their separation-active surface area. Filter materials made from thermally fixed fibre nonwovens were processed to form plicated filter bags of the same structural volume but with a surface area increased by a factor of 2.5. Integrated inlet nozzles were developed to allow these elements to be cleaned of dust deposits. These nozzles were also studied in basic filter-technology tests. A test rig supplied design findings which were included in a study to develop new generations of dedusters. A reduction of design volume and an increase of through-put rate greater than 20% could be predicted. Service tests with modified filter materials were run for ventilation-air dust dust removal both for whole faces and for face segments. The benefits of filter technology for face, face opening and drifting were highlighted. New methods for wetting and transport of the dust removed from the dedusters were developed. New concepts of exhaust-air filter separators allow flat storage bunkers to be used in pneumatic conveyance of building materials at the face. (orig.)

  7. Carbon fibre composite for ventilation air methane (VAM) capture

    Energy Technology Data Exchange (ETDEWEB)

    Thiruvenkatachari, Ramesh [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia); Su Shi, E-mail: Shi.Su@csiro.au [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia); Yu Xinxiang [Commonwealth Scientific and Industrial Research Organisation (CSIRO), PO Box 883, Kenmore, Queensland 4069 (Australia)

    2009-12-30

    Coal mine methane (CMM) is not only a hazardous greenhouse gas but is also a wasted energy resource, if not utilised. This paper evaluates a novel adsorbent material developed for capturing methane from ventilation air methane (VAM) gas in underground coal mines. The adsorbent material is a honeycomb monolithic carbon fibre composite (HMCFC) consisting of multiple parallel flow-through channels and the material exhibits unique features including low pressure drop, good mechanical properties, ability to handle dust-containing gas streams, good thermal and electrical conductivity and selective adsorption of gases. During this study, a series of HMCFC adsorbents (using different types of carbon fibres) were successfully fabricated. Experimental data demonstrated the proof-of-concept of using the HMCFC adsorbent to capture methane from VAM gas. The adsorption capacity of the HMCFC adsorbent was twice that of commercial activated carbon. Methane concentration of 0.56% in the inlet VAM gas stream is reduced to about 0.011% after it passes through the novel carbon fibre composite adsorbent material at ambient temperature and atmospheric pressure. This amounts to a maximum capture efficiency of 98%. These encouraging laboratory scale studies have prompted further large scale trials and economic assessment.

  8. Carbon fibre composite for ventilation air methane (VAM) capture.

    Science.gov (United States)

    Thiruvenkatachari, Ramesh; Su, Shi; Yu, Xin Xiang

    2009-12-30

    Coal mine methane (CMM) is not only a hazardous greenhouse gas but is also a wasted energy resource, if not utilised. This paper evaluates a novel adsorbent material developed for capturing methane from ventilation air methane (VAM) gas in underground coal mines. The adsorbent material is a honeycomb monolithic carbon fibre composite (HMCFC) consisting of multiple parallel flow-through channels and the material exhibits unique features including low pressure drop, good mechanical properties, ability to handle dust-containing gas streams, good thermal and electrical conductivity and selective adsorption of gases. During this study, a series of HMCFC adsorbents (using different types of carbon fibres) were successfully fabricated. Experimental data demonstrated the proof-of-concept of using the HMCFC adsorbent to capture methane from VAM gas. The adsorption capacity of the HMCFC adsorbent was twice that of commercial activated carbon. Methane concentration of 0.56% in the inlet VAM gas stream is reduced to about 0.011% after it passes through the novel carbon fibre composite adsorbent material at ambient temperature and atmospheric pressure. This amounts to a maximum capture efficiency of 98%. These encouraging laboratory scale studies have prompted further large scale trials and economic assessment.

  9. Fibre concentrations and size distributions of airborne fibres in several European man-made mineral fibre plants.

    Science.gov (United States)

    Dodgson, J; Ottery, J; Cherrie, J W; Harrison, G E

    1980-01-01

    Although the nominal diameters of fibres produced in the glass and rock wool industries are usually 6-15 micrometers, these products contain a small proportion of respirable fibres (less than 3 micrometers diameter). Particular significance has been attached to the biological risk arising from the long (greater than 10 micrometers), fine (less than 1 micrometers) fibres. Therefore, the medical research sponsored by the Joint European Medical Research Board into the effects of man-made fibres on health has included detailed environmental studies on both the exposure levels to respirable fibres and the fibre size distributions at the European plants selected for epidemiological work. This paper summarizes the results obtained so far. The size distributions (length and diameter) of the airborne man-made mineral fibres are compared with similar data previously reported for airborne asbestos fibres.

  10. Thermal analysis of bicomponent fibres

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, J.I. [Room I-320-D, ETS Ingenieros Industriales, Universidad de Malaga, Plaza El Ejido, s/n, 29013-Malaga (Spain)

    2007-02-15

    A one-dimensional model of amorphous bicomponent spun fibres derived from the use of perturbation methods based on the slenderness ratio is presented. The model accounts for gravitational, surface tension, axial heat conduction, viscous dissipation and the nonlinear dependence of the dynamic viscosity law on temperature, but does not consider latent heat effects and the radial gradients of temperature and assumes Newtonian rheology. Studies on the effects of the thermal parameters on the compound fibre's geometry and solidification have been performed, and show that the activation energy of the dynamic viscosity laws have a paramount effect on the fibre's cooling, shape, and axial stresses on the core and sheath. In particular, it is shown that, when the activation energy of the viscosity law for the core is higher than that for the sheath, the axial stresses on the core are monotonic functions of the distance along the fibre and higher than those on the sheath, whereas those in the latter may exhibit a nonmonotonic behavior as functions of the thermal conductivity, heat losses and thermal inertia. Despite its limitations, the model presented here represents an improvement over available one-dimensional models for non-isothermal compound or bicomponent fibres. (author)

  11. Biopersistence of man-made vitreous fibres.

    Science.gov (United States)

    Muhle, H; Bellmann, B

    1995-10-01

    Methods for the determination of biodurability of man-made vitreous fibres are reviewed. For mineral wools the first step was the preparation of respirable fibre fractions. Fibres were administered to rats by inhalation or by intratracheal instillation. After serial sacrifice their lungs were digested by low-temperature ashing or by hypochlorite. The total number of fibres per lung and the distributions of length and diameter were analysed by electron microscopy. This resulted in a bivariate distribution of fibres at the various sacrifice dates. If the logarithm of the number of fibres decreased approximately linearly with time after exposure then the elimination kinetics of fibres can be characterized by a half-time. The half-times were compared between various experiments with rats exposed to mineral wool samples. In summary good agreement was found for the elimination of fibres after long-term inhalation and intratracheal instillation whereas shorter half-times were found after short-term inhalation.

  12. Underwater Acoustic Sensing with Optical Fibres

    Directory of Open Access Journals (Sweden)

    V. V. Rampal

    1982-01-01

    Full Text Available The use of optical fibres for the detection of acoustic pressure underwater has been discussed with particular reference to the recent literature on the development of fibre optic hydrophones.

  13. Hollow Core Photonic Crystal Fibre Comprising a Fibre Grating in the Cladding and its Applications

    DEFF Research Database (Denmark)

    2010-01-01

    An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction.......An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction....

  14. Exposure assessment for airborne man-made mineral fibres: the role of fibre dimensions.

    Science.gov (United States)

    Rosenthal, F S

    1993-08-01

    Environmental exposures to man-made mineral fibres (MMMF) typically contain fibres which are polydisperse with respect to fibre dimensions. Fibre dimensions may influence their biological action through effects on: the efficiency of transport to target tissues; the residence time in target tissues; and the biological activity of fibres in contact with target cells. This variability of biological activity vs fibre dimensions should be accounted for when assessing exposure for epidemiological studies of the risk of cancer in subjects exposed to MMMF. In order to provide insight into the influence of fibre dimensions on the potential carcinogenicity of MMMF, this paper reviews literature concerning the sites of lung tumours, regional fibre deposition, biological effects of fibres in in vivo and in vitro systems, dissolution rates of fibres and rates of physiological clearance of inhaled particles. Tumorigenicity of fibres in contact with target tissue appears to be primarily a function of fibre length, whereas both fibre diameter and fibre length may affect the penetration of fibres through the respiratory tract as well as their residence time in target tissues. A methodology is presented to use this information to compute estimates of biologically effective exposure from the joint distribution of fibre lengths and diameters found in an environmental exposure.

  15. LHCb Upgrade: Scintillating Fibre Tracker

    Science.gov (United States)

    Tobin, Mark

    2016-07-01

    The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less read-out system. All front-end electronics will be replaced and several sub-detectors must be redesigned to cope with higher occupancy. The current tracking detectors downstream of the LHCb dipole magnet will be replaced by the Scintillating Fibre (SciFi) Tracker. The SciFi Tracker will use scintillating fibres read out by Silicon Photomultipliers (SiPMs). State-of-the-art multi-channel SiPM arrays are being developed to read out the fibres and a custom ASIC will be used to digitise the signals from the SiPMs. The evolution of the design since the Technical Design Report in 2014 and the latest R & D results are presented.

  16. Fibre Optics In Coal Mining

    Science.gov (United States)

    Cooper, Paul

    1984-08-01

    Coal mines have a number of unique problems which affect the use of fibre optic technology. These include a potentially explosive atmosphere due to the evolution of methane from coal, and a dirty environment with no cleaning facilities readily available. Equipment being developed by MRDE to allow the exploitation of optical fibres underground includes: A hybrid electrical/fibre optic connector for the flexible power trailing cable of the coal-face shearer; An Intrinsically Safe (IS) pulsed laser transmitter using Frequency Shift Key (FSK) data modulation; An IS Avalanche Photo Diode Receiver suitable for pulsed & continuous wave optical signals; A mine shaft and roadway cable/ connector system incorporating low loss butt-splices and preterminated demountable connectors.

  17. LHCb Upgrade: Scintillating Fibre Tracker

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, Mark, E-mail: Mark.Tobin@epfl.ch

    2016-07-11

    The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less read-out system. All front-end electronics will be replaced and several sub-detectors must be redesigned to cope with higher occupancy. The current tracking detectors downstream of the LHCb dipole magnet will be replaced by the Scintillating Fibre (SciFi) Tracker. The SciFi Tracker will use scintillating fibres read out by Silicon Photomultipliers (SiPMs). State-of-the-art multi-channel SiPM arrays are being developed to read out the fibres and a custom ASIC will be used to digitise the signals from the SiPMs. The evolution of the design since the Technical Design Report in 2014 and the latest R & D results are presented.

  18. Wavelength Filters in Fibre Optics

    CERN Document Server

    Venghaus, Herbert

    2006-01-01

    Wavelength filters constitute an essential element of fibre-optic networks. This book gives a comprehensive account of the principles and applications of such filters, including their technological realisation. After an introductory chapter on wavelength division multiplexing in current and future fibre optic networks follows a detailed treatment of the phase characteristics of wavelength filters, a factor frequently neglected but of significant importance at high bit rates. Subsequent chapters cover three-dimensional reflection of gratings, arrayed waveguide gratings, fibre Bragg gratings, Fabry-Perot filters, dielectric multilayer filters, ring filters, and interleavers. The book explains the relevant performance parameters, the particular advantages and shortcomings of the various concepts and components, and the preferred applications. It also includes in-depth information on the characteristics of both commercially available devices and those still at the R&D stage. All chapters are authored by inter...

  19. Ductility Performance of Hybrid Fibre Reinforced Concrete

    OpenAIRE

    S. Eswari; P.N. Raghunath; Suguna, K

    2008-01-01

    This study presents a study on the ductility performance of hybrid fibre reinforced concrete. The influence of fibre content on the ductility performance of hybrid fibre reinforced concrete specimens having different fibre volume fractions was investigated. The parameters of investigation included modulus of rupture, ultimate load, service load, ultimate and service load deflection, crack width, energy ductility and deflection ductility. A total of 27 specimens, 100×100×500 mm, were tested to...

  20. Photonic crystal fibres and effective index approaches

    DEFF Research Database (Denmark)

    Riishede, Jesper; Libori, Stig E. Barkou; Bjarklev, Anders Overgaard

    2001-01-01

    Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres.......Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres....

  1. Photonic-crystal fibre: Mapping the structure

    DEFF Research Database (Denmark)

    Markos, Christos

    2015-01-01

    The demonstration of real-time and non-destructive Doppler-assisted tomography of the internal structure of photonic-crystal fibres could aid the fabrication of high-quality fibres with enhanced performance.......The demonstration of real-time and non-destructive Doppler-assisted tomography of the internal structure of photonic-crystal fibres could aid the fabrication of high-quality fibres with enhanced performance....

  2. Local fibred right adjoints are polynomial

    DEFF Research Database (Denmark)

    Kock, Anders; Kock, Joachim

    2013-01-01

    For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense......For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense...

  3. Optical Fibre Based Frequency Shifters Project

    Science.gov (United States)

    1991-01-28

    A fibre optic frequency shifter can be used to replace the Bragg cell acousto-optic modulator, currently used to generate low frequency optical...carriers, in fibre optic communications and sensor systems. This new form of frequency shifter, being an all fibre device, in which the propagating optical...large number of workers in recent years, (for example references [2-81 and those contained therein). The main elements of a fibre - optic frequency

  4. Optimal Extraction of Fibre Optic Spectroscopy

    CERN Document Server

    Sharp, R

    2009-01-01

    We report an optimal extraction methodology, for the reduction of multi-object fibre spectroscopy data, operating in the regime of tightly packed (and hence significantly overlapping) fibre profiles. The routine minimises crosstalk between adjacent fibres and statistically weights the extraction to reduce noise. As an example of the process we use simulations of the numerous modes of operation of the AAOmega fibre spectrograph and observational data from the SPIRAL Integral Field Unit at the Anglo-Australian Telescope.

  5. Fibre Optic Communication Key Devices

    CERN Document Server

    Grote, Norbert

    2012-01-01

    The book gives an in-depth description of the key devices of current and next generation fibre optic communication networks. In particular, the book covers devices such as semiconductor lasers, optical amplifiers, modulators, wavelength filters, and detectors but the relevant properties of optical fibres as well. The presentations include the physical principles underlying the various devices, the technologies used for the realization of the different devices, typical performance characteristics and limitations, and development trends towards more advanced components are also illustrated. Thus the scope of the book spans relevant principles, state-of-the-art implementations, the status of current research and expected future components.

  6. Portable smartphone optical fibre spectrometer

    Science.gov (United States)

    Hossain, Md. Arafat; Canning, John; Cook, Kevin; Jamalipour, Abbas

    2015-09-01

    A low cost, optical fibre based spectrometer has been developed on a smartphone platform for field-portable spectral analysis. Light of visible wavelength is collected using a multimode optical fibre and diffracted by a low cost nanoimprinted diffraction grating. A measurement range over 300 nm span (λ = 400 to 700 nm) is obtained using the smartphone CMOS chip. The spectral resolution is Δλ ~ 0.42 nm/screen pixel. A customized Android application processed the spectra on the same platform and shares with other devices. The results compare well with commercially available spectrometer.

  7. Friction and wear of human hair fibres

    Science.gov (United States)

    Bowen, James; Johnson, Simon A.; Avery, Andrew R.; Adams, Michael J.

    2016-06-01

    An experimental study of the tribological properties of hair fibres is reported, and the effect of surface treatment on the evolution of friction and wear during sliding. Specifically, orthogonally crossed fibre/fibre contacts under a compressive normal load over a series of 10 000 cycle studies are investigated. Reciprocating sliding at a velocity of 0.4 mm s-1, over a track length of 0.8 mm, was performed at 18 °C and 40%-50% relative humidity. Hair fibres retaining their natural sebum were studied, as well as those stripped of their sebum via hexane cleaning, and hair fibres conditioned using a commercially available product. Surface topography modifications resulting from wear were imaged using scanning electron microscopy and quantified using white light interferometry. Hair fibres that presented sebum or conditioned product at the fibre/fibre junction exhibited initial coefficients of friction at least 25% lower than those that were cleaned with hexane. Coefficients of friction were observed to depend on the directionality of sliding for hexane cleaned hair fibres after sufficient wear cycles that cuticle lifting was present, typically on the order 1000 cycles. Cuticle flattening was observed for fibre/fibre junctions exposed to 10 mN compressive normal loads, whereas loads of 100 mN introduced substantial cuticle wear and fibre damage.

  8. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available animal hair fibres L Hunter, CSIR and Nelson Mandela Metropolitan University (NMMU), South Africa Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury...

  9. Occupational ceramic fibres dermatitis in Poland.

    Science.gov (United States)

    Kieć-Swierczyńska, M; Wojtczak, J

    2000-07-01

    Recently, the use of asbestos has been considerably limited in Poland, with the simultaneous increase in the manufacture, processing and application of man-made mineral fibres, which includes ceramic fibres. The aims of this study were (1) to assess the type and frequency of dermal changes caused by the irritant activity of ceramic fibres among workers at the plants that manufacture packing and insulation products; and (2) to compare the irritant activity of Polish-made L-2 and L-3 ceramic fibres with that of the Thermowool ceramic fibres made in England. Workers (n = 226) who were exposed to ceramic fibres underwent dermatological examination. Patch tests with the standard allergen set, together with samples of the fibres L-2, L-3, and Thermowool fibres, were applied to all the workers. It has been shown that the Polish-made L-2 and L-3 fibres differed from Thermowool fibres in that the L-2 and L-3 fibres contained zirconium and were coarser. The proportion of filaments with diameters above 3 microns was 11.1% in the L-3 fibre and 6.3% in the L-2 fibre samples. The Thermowool fibre did not contain filaments thicker than 3 microns. Evident dermal changes, resulting from strong irritant activity of the fibres, were detected in 109 (48.2%) of the workers examined. Irritant contact dermatitis acuta (maculae, sometimes papulae and small crusts on the upper extremities, trunk, and lower extremities), disappearing after 2-3 days, was found in 50 (22.1%) workers. Irritant contact dermatitis chronica (diffuse permanent erythema with numerous telangiectasiae on the lateral portions of the face and neck, on the trunk, behind the auricles) was detected in 40 (17.7%) workers. The remaining 19 (8.4%) workers had both types of dermal change. All examined workers complained of very strong itching. The results of the patch tests confirmed the irritant activity of the ceramic fibres. Erythema without oedema, persisting for up to 96 h, appeared at the places where the fibres had

  10. Physics of interstellar dust

    CERN Document Server

    Krugel, Endrik

    2002-01-01

    The dielectric permeability; How to evaluate grain cross sections; Very small and very big particles; Case studies of Mie calculus; Particle statistics; The radiative transition probability; Structure and composition of dust; Dust radiation; Dust and its environment; Polarization; Grain alignment; PAHs and spectral features of dust; Radiative transport; Diffuse matter in the Milky Way; Stars and their formation; Emission from young stars. Appendices Mathematical formulae; List of symbols.

  11. Dust-off

    OpenAIRE

    Maycroft, Neil; Cheang, Shu Lea

    2015-01-01

    The fan of a motherboard switches on and off intermittently. It blows household dust, removed from the inside of a computer carcass, into the air. The dust then settles onto the motherboard, to be blown off again. This continual movement of dust is contained in the piece. However, it should remind us that the ceaseless creation and motion of unconfined dust accompanies all stages of the e-waste journey.

  12. Dust-off

    OpenAIRE

    Maycroft, Neil; Cheang, Shu Lea

    2015-01-01

    The fan of a motherboard switches on and off intermittently. It blows household dust, removed from the inside of a computer carcass, into the air. The dust then settles onto the motherboard, to be blown off again. This continual movement of dust is contained in the piece. However, it should remind us that the ceaseless creation and motion of unconfined dust accompanies all stages of the e-waste journey.

  13. Dust in the Universe

    Science.gov (United States)

    Hemenway, Mary Kay; Armosky, Brad J.

    2004-01-01

    Space is seeming less and less like empty space as new discoveries and reexaminations fill in the gaps. And, ingenuity and technology, like the Spitzer Space Telescope, is allowing examination of the far reaches of the Milky Way and beyond. Even dust is getting its due, but not the dust everyone is familiar with. People seldom consider the dust in…

  14. [New documentation sheet for medical examination due to exposures to dust].

    Science.gov (United States)

    Hagemeyer, O; Mannes, E; Koppisch, D; Otten, H; Dahmann, D

    2004-05-01

    With beginning of the year 2004 a new documentation sheet for occupational preventive medical examinations according to exposures to mineral dust (quartz, asbestos, ceramic fibres) will replace the existing sheet. The new investigation sheet is presented in this publication and changes are described.

  15. A PHOTONIC BAND GAP FIBRE

    DEFF Research Database (Denmark)

    1999-01-01

    An optical fibre having a periodicidal cladding structure provididing a photonic band gap structure with superior qualities. The periodical structure being one wherein high index areas are defined and wherein these are separated using a number of methods. One such method is the introduction...

  16. Cool application for Optical Fibres

    CERN Multimedia

    2001-01-01

    In a new first for CERN, optical fibres have been put on test to measure very low temperatures. If these tests prove successful, this new technology could lead to important cost-saving changes in the way the temperatures of superconducting magnets are measured. There was excitement in the air last March when the team led by Walter Scandale and Luc Thévenaz tested very low temperature measurement using optical fibres. This spring in CERN's Cryogenics lab an idea was put to the test as a new kind of low-temperature thermometry using optical fibres was tested down to 2 Kelvin (around 300 degrees below room temperature), and the first results are looking good. Optical fibres are well known for their ability to carry large amounts of data around the world, but it is less well known that they can be used for measuring temperatures. The intuition that they might be able to measure very low temperatures - such as those of the LHC magnets - came to the attention of CERN's Walter Scandale at the Optical Fi...

  17. Compressibility of hemp bast fibres

    NARCIS (Netherlands)

    Westenbroek, A.P.H.; Roekel, van G.J.; Jong, de E.; Weickert, G.; Westerterp, R.K.

    1999-01-01

    A force-based characterization of the extrusion pulping process is necessary to be able to predict the effects of extrusion on fibres. To determine which forces are beneficial and which only cause energy consumption, the nature and the origin of the forces have to be known. This paper discusses the

  18. Threshold temperature optical fibre sensors

    Science.gov (United States)

    Stasiewicz, K. A.; Musial, J. E.

    2016-12-01

    This paper presents a new approach to manufacture a threshold temperature sensor based on a biconical optical fibre taper. The presented sensor employs the influence of variable state of concentration of some isotropic materials like wax or paraffin. Application of the above- mentioned materials is an attempt to prove that there is a possibility to obtain a low-cost, repeatable and smart sensor working as an in-line element. Optical fibre taper was obtained from a standard single mode fibre (SMF28®) by using a low pressure gas burner technique. The diameter of the manufactured tapers was 6.0 ± 0.5 μm with the length of elongation equal to 30.50 ± 0.16 mm. The applied technology allowed to produce tapers with the losses of 0.183 ± 0.015 dB. Application of materials with different temperature transition points made it possible to obtain the threshold work at the temperatures connected directly with their conversion temperature. External materials at the temperatures above their melting points do not influence the propagation losses. For each of them two types of the protection area and position of the optical fibre taper were applied.

  19. Nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch

    is potentially the case for microstructured polymer optical fibres (mPOFs). Another advantage is that polymer materials have a higher biocompatibility than silica, meaning that it is easier to bond certain types of biosensor materials to a polymer surface than to silica. As with silica PCFs, it is difficult...

  20. Strength of Concrete Containing Basalt Fibre

    OpenAIRE

    2015-01-01

    This paper presents the comparative study of effect of basalt fibre on compressive and split tensile strength of M40 grade concrete. The basalt fibre was mixed in concrete by (0.5%, 1%, and 1.5%) of its total weight of cement in concrete. Results indicated that the strength increases with increase of basalt fibre content up to 1.0% beyond that there is a reduction in strength on increasing basalt fibre. The results show that the concrete specimen with 1.0% of basalt fibre gives be...

  1. Characterisation of Natural Fibre Reinforcements and Composites

    Directory of Open Access Journals (Sweden)

    Richard K. Cullen

    2013-01-01

    Full Text Available Recent EU directives (e.g., ELV and WEEE have caused some rethinking of the life cycle implications of fibre reinforced polymer matrix composites. Man-made reinforcement fibres have significant ecological implications. One alternative is the use of natural fibres as reinforcements. The principal candidates are bast (plant stem fibres with flax, hemp, and jute as the current front runners. The work presented here will consider the characterisation of jute fibres and their composites. A novel technique is proposed for the measurement of fibre density. The new rule of mixtures, extended for noncircular cross-section natural fibres, is shown to provide a sensible estimate for the experimentally measured elastic modulus of the composite.

  2. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...... of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish...... the same amount of air pores as in the corresponding concrete without fibres...

  3. Elastic fibres in health and disease.

    Science.gov (United States)

    Baldwin, Andrew K; Simpson, Andreja; Steer, Ruth; Cain, Stuart A; Kielty, Cay M

    2013-08-20

    Elastic fibres are insoluble components of the extracellular matrix of dynamic connective tissues such as skin, arteries, lungs and ligaments. They are laid down during development, and comprise a cross-linked elastin core within a template of fibrillin-based microfibrils. Their function is to endow tissues with the property of elastic recoil, and they also regulate the bioavailability of transforming growth factor β. Severe heritable elastic fibre diseases are caused by mutations in elastic fibre components; for example, mutations in elastin cause supravalvular aortic stenosis and autosomal dominant cutis laxa, mutations in fibrillin-1 cause Marfan syndrome and Weill-Marchesani syndrome, and mutations in fibulins-4 and -5 cause autosomal recessive cutis laxa. Acquired elastic fibre defects include dermal elastosis, whereas inflammatory damage to fibres contributes to pathologies such as pulmonary emphysema and vascular disease. This review outlines the latest understanding of the composition and assembly of elastic fibres, and describes elastic fibre diseases and current therapeutic approaches.

  4. Retained laser fibre: insights and management.

    Science.gov (United States)

    Lekich, C; Hannah, P

    2014-06-01

    To describe a case of retained endovenous laser fibre. To review the literature and Food and Drug Administration device failure reports. To suggest protocols for avoiding this complication and a method of removal. A case of retained fibre removal is described. Fibre removal techniques in vivo and ex vivo in a bovine model on the laboratory bench are presented. Successful in vivo and ex vivo fibre removal was performed using duplex ultrasound scan guided phlebectomy techniques. Unexplained measured fibre-length discrepancies due to misleading manufacturer's packaging was discovered. Simple ultrasound-guided micro-phlebectomy techniques can be used to remove retained laser fibres in the office environment. Laser fibre length measurements before and after treatment are recommended. Some preventive guidelines are described to avoid, or at least diagnose immediately, this complication, such as the 'Laser Eclipse Sign'. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

  5. A comparison of exposures to refractory ceramic fibres over multiple work shifts.

    Science.gov (United States)

    Hall, G S; Rice, C H; Lockey, J E; Lemasters, G K; Gartside, P S

    1997-10-01

    As part of an ongoing, industry-wide study in the manufacture of refractory ceramic fibres (RCF), time weighted average (TWA) exposures have been collected at five facilities according to a standardised protocol. Work activities were grouped into dust zones (DZs). Persons to be sampled were randomly selected according to a protocol designed to assure that at least one sample was collected annually from each DZ; each work shift is also sampled at least annually. TWA exposures calculated over a sampling period of at least 360 min were included in the data set. DZs were combined into one of three groups (DZGs): fibre production; vacuum processes; other. The data were analysed to identify any differences by DZG between airborne fibre exposures, by the shift worked at each facility, and across all facilities. There were no statistically significant shift-related differences detected between airborne fibre exposures across the five RCF facilities when analysed as a group. Within four of the facilities, no shift-related differences were detected between airborne fibre exposures; however, at one facility, first and third shift exposures were statistically different. No documentation related to job activities was found to account for the observation. The data generally support the use of a single exposure estimate for each DZG in each of these facilities, regardless of shift worked. Researchers reconstructing exposure and not able to determine the shift worked by study subjects may find these results useful, but are cautioned that substantial differences in exposure across shifts may exist in other types of manufacturing.

  6. Characterisation of Flax Fibres and Flax Fibre Composites. Being cellulose based sources of materials

    DEFF Research Database (Denmark)

    Aslan, Mustafa

    that currently have the largest market share for composite applications. However, the most critical limitation in the use of cellulosic fibre composites for structural applications is the lack of well described fibre properties, in particular, the tensile strength. This is due to variations in fibre morphology...... of the internal cell wall structures. This is in contrast to the crack growth in brittle ceramic and glass fibres. Moreover, two typical stress-strain curves (linear and non-linear) measured for the flax fibres were found to be correlated with the amount of defected region in the fibres. The defects are induced...... a similar microstructure at low fibre weight fractions. However, when the fibre content is increased, a difference in porosity content can be observed from the composite cross sections. The nominal tensile strength of the unidirectional flax fibre/LPET composites is measured in the range 180 to 340 MPa...

  7. Toxicity of lunar dust

    CERN Document Server

    Linnarsson, Dag; Fubini, Bice; Gerde, Per; Karlsson, Lars L; Loftus, David J; Prisk, G Kim; Staufer, Urs; Tranfield, Erin M; van Westrenen, Wim

    2012-01-01

    The formation, composition and physical properties of lunar dust are incompletely characterised with regard to human health. While the physical and chemical determinants of dust toxicity for materials such as asbestos, quartz, volcanic ashes and urban particulate matter have been the focus of substantial research efforts, lunar dust properties, and therefore lunar dust toxicity may differ substantially. In this contribution, past and ongoing work on dust toxicity is reviewed, and major knowledge gaps that prevent an accurate assessment of lunar dust toxicity are identified. Finally, a range of studies using ground-based, low-gravity, and in situ measurements is recommended to address the identified knowledge gaps. Because none of the curated lunar samples exist in a pristine state that preserves the surface reactive chemical aspects thought to be present on the lunar surface, studies using this material carry with them considerable uncertainty in terms of fidelity. As a consequence, in situ data on lunar dust...

  8. Asbestos fibres inhibit the in vitro activity of lymphokine-activated killer (LAK) cells from healthy individuals and patients with malignant mesothelioma.

    Science.gov (United States)

    Manning, L S; Davis, M R; Robinson, B W

    1991-01-01

    Asbestos exposure is associated with an increased incidence of several malignancies, including malignant mesothelioma (MM). This study evaluates the relationship between asbestos exposure and the in vitro generation and function of LAK cells, an immune effector cell population with powerful lytic activity against MM cells. Both serpentine (chrysotile) and amphibole (amosite and crocidolite) forms of asbestos fibres suppress LAK cell generation, viability (by 5-11%, P less than 0.02) and cell recovery (by 13-15%, P less than 0.02). However, the LAK cells generated in the presence of the amphiboles were as effective as unexposed cells in lysing both standard tumour cell targets (K562, 56.4% lysis versus 61.5%, respectively, P greater than 0.5; NS; Daudi, 60.5% lysis versus 64.5% P greater than 0.5; NS), and MM tumour cell targets (mean of three MM cell lines 48.3% versus 46.3%, P greater than 0.5; NS), whereas the function of LAK cells generated in the presence of chrysotile was significantly reduced against three out of the five tumour cell targets tested (P less than 0.03). In the presence of asbestos fibres, LAK cell function was reduced against all five tumour cell targets (P less than 0.01), irrespective of whether the cell donors were healthy individuals or patients with MM. NK cell activity was also suppressed (P less than 0.01). The serpentine form of asbestos, chrysotile, was significantly more suppressive of both effector cell functions than either of the amphiboles (P less than 0.01). These findings suggest that asbestos exposure may suppress the function and in some instances the generation of immune effector cell mechanisms, thereby increasing the risk of disease and malignancy. PMID:1846329

  9. Fundamentals of fibre-reinforced soil engineering

    CERN Document Server

    Shukla, Sanjay Kumar

    2017-01-01

    This book is intended to serve as a one-stop reference on fibre-reinforced soils. Over the past 30-35 years, the engineering behaviour of randomly distributed/oriented fibre-reinforced soil, also called simply fibre-reinforced soil, has been investigated in detail by researchers and engineers worldwide. Waste fibres (plastic waste fibres, old tyre fibres, etc.) create disposal and environmental problems. Utilization of such fibres in construction can help resolve these concerns. Research studies and some field applications have shown that the fibres can be utilized in large quantities in geotechnical and civil engineering applications in a cost-effective and environmentally friendly manner. This book covers a complete description of fibres, their effects when included within a soil or other similar materials such as the fly ash, and their field applications. It gives a detailed view of fibre-reinforced soil engineering. The book will be useful to students, professional, and researchers alike, and can also ser...

  10. Structural investigation of Mimosa pudica Linn fibre

    Science.gov (United States)

    Patra, S. R.; Pattojoshi, P.; Tiwari, T. N.; Mallick, B.

    2016-12-01

    Sensitive plant (Mimosa pudica Linn.) fibre is a natural fibre with electrically conductive property. Because of its electro-active sensing nature, it has been found very interesting among physicists, chemists, biologists, material scientists and technologists. So far as our knowledge is concerned; there is no report on the X-ray structure of M. pudica fibre using diffraction technique. In the present report, the M. pudica fibre has been extracted from the stem of the herb by sinking the stem in 10% NaOH solution for one week. The diffraction pattern of the fibre is found out to be cellulose-I. The effect of the fibre structure and its orientation due to different mounting have been investigated using X-ray diffraction technique. The I max of cellulose-I has been observed along (002) and (10overline{1)} for the perpendicular and parallel mounting of the native-fibre, respectively. Full width at half maxima of the diffraction profile turns out to be decreased with fibre orientation. Dimension of crystallite size D hkl estimated in the perpendicular mounting D_{hkl}^{ bot } is more as compared to that of the parallel mounting D_{hkl}^{{^{allel } }} . The smallest crystallite sizes observed in both parallel and perpendicular mounting are 18.78 and 30.78 Å respectively. It is expected that the present study may help to analyse the X-ray diffraction of fibre materials in general and natural fibres in particular.

  11. Structural investigation of Mimosa pudica Linn fibre

    Science.gov (United States)

    Patra, S. R.; Pattojoshi, P.; Tiwari, T. N.; Mallick, B.

    2017-04-01

    Sensitive plant ( Mimosa pudica Linn.) fibre is a natural fibre with electrically conductive property. Because of its electro-active sensing nature, it has been found very interesting among physicists, chemists, biologists, material scientists and technologists. So far as our knowledge is concerned; there is no report on the X-ray structure of M. pudica fibre using diffraction technique. In the present report, the M. pudica fibre has been extracted from the stem of the herb by sinking the stem in 10% NaOH solution for one week. The diffraction pattern of the fibre is found out to be cellulose-I. The effect of the fibre structure and its orientation due to different mounting have been investigated using X-ray diffraction technique. The I max of cellulose-I has been observed along (002) and (10\\overline{1)} for the perpendicular and parallel mounting of the native-fibre, respectively. Full width at half maxima of the diffraction profile turns out to be decreased with fibre orientation. Dimension of crystallite size D hkl estimated in the perpendicular mounting D_{hkl}^{ \\bot } is more as compared to that of the parallel mounting D_{hkl}^{{^{allel } }}. The smallest crystallite sizes observed in both parallel and perpendicular mounting are 18.78 and 30.78 Å respectively. It is expected that the present study may help to analyse the X-ray diffraction of fibre materials in general and natural fibres in particular.

  12. Fibre optic communication key devices

    CERN Document Server

    Grote, Norbert

    2017-01-01

    The book gives an in-depth description of key devices of current and next generation fibre optic communication networks. Devices treated include semiconductor lasers, optical amplifiers, modulators, wavelength filters and other passives, detectors, all-optical switches, but relevant properties of optical fibres and network aspects are included as well. The presentations include the physical principles underlying the various devices, technologies used for their realization, typical performance characteristics and limitations, but development trends towards more advanced components are also illustrated. This new edition of a successful book was expanded and updated extensively. The new edition covers among others lasers for optical communication, optical switches, hybrid integration, monolithic integration and silicon photonics. The main focus is on Indium phosphide-based structures but silicon photonics is included as well. The book covers relevant principles, state-of-the-art implementations, status of curren...

  13. Electrospun cerium nitrate/polymer composite fibres:synthesis, characterization and fibre-division model

    Institute of Scientific and Technical Information of China (English)

    Li Meng-Meng; Long Yun-Ze; Yin Hong-Xing; Zhang Zhi-Ming

    2011-01-01

    Cerium (III)nitrate/poly(vinylpyrrolidone)(Ce(NO3)3/PVP)composite fibres have been prepared by electrospinning. After calcining the composite fibres in air at 500℃, CeO2 nanowires were obtained. The characterizations of the as-spun composite fibres and resultant nanowires have been carried out by a scanning electron microscope (SEM),an infrared spectrometer, an x-ray diffractometer and a fluorescence spectrophotometer. Interestingly, some unusual ribbon-like or twin fibres were observed besides the common fibres with circular or elliptic cross sections. We developed a fibre-division model resulting from Coulomb repulsion and solvent vaporization to interpret the formation of the ribbona or twin fibres, which has been confirmed by the SEM studies. Our results also indicate that the formation of the ribbons or twin fibres is less dependent on operation voltage and work distance.

  14. Orientation distribution of fibres in a channel flow of fibre suspension

    Institute of Scientific and Technical Information of China (English)

    Lin Jian-Zhong; Li Jun; Zhang Wei-Feng

    2005-01-01

    The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.

  15. Interfacial Adhesion Characteristics of Kenaf Fibres Subjected to Different Polymer Matrices and Fibre Treatments

    Directory of Open Access Journals (Sweden)

    Umar Nirmal

    2014-01-01

    Full Text Available This study is aimed at determining the interfacial adhesion strength (IAS of kenaf fibres using different chemical treatments in hydrochloric (HCl and sodium hydroxide (NaOH with different concentrations. Single fibre pullout tests (SFPT were carried out for both untreated and treated fibres partially embedded into three different polymer matrices; polyester, epoxy, and polyurethane (PU as reinforcement blocks and tested under dry loading conditions. The study revealed that kenaf fibres treated with 6% NaOH subjected to polyester, epoxy, and PU matrices exhibits excellent IAS while poor in acidic treatment. The effect of SFPT results was mainly attributed to chemical composition of the fibres, types of fibre treatments, and variation in resin viscosities. By scanning electron microscopy examination of the material failure morphology, the fibres experienced brittle and ductile fibre breakage mechanisms after treatment with acidic and alkaline solutions.

  16. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish......Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...

  17. Muscle fibre type and aetiology of obesity.

    Science.gov (United States)

    Wade, A J; Marbut, M M; Round, J M

    1990-04-07

    Proportions of slow (type 1) muscle fibres of the vastus lateralis and percentage body fat were measured in 11 healthy sedentary men. The proportion of slow muscle fibres was inversely related to fatness; at least 40% of the variability in fatness may be related to variation in muscle fibre type. Metabolic evidence in 50 men, provided by the respiratory exchange ratio (RER) during cycle ergometry, indicated that fatter men (or, in the subset of 11 men, those with a low proportion of slow muscle fibres) combusted less fat during work at 100 W than did lean men (or those with a high proportion of slow fibres). The effects of fitness and of body size were excluded in the analysis. The evidence supports the hypothesis that muscle fibre type is an aetiological factor for obesity.

  18. Operational Dust Prediction

    Science.gov (United States)

    Benedetti, Angela; Baldasano, Jose M.; Basart, Sara; Benincasa, Francesco; Boucher, Olivier; Brooks, Malcolm E.; Chen, Jen-Ping; Colarco, Peter R.; Gong, Sunlin; Huneeus, Nicolas; Jones, Luke; Lu, Sarah; Menut, Laurent; Morcrette, Jean-Jacques; Mulcahy, Jane; Nickovic, Slobodan; Garcia-Pando, Carlos P.; Reid, Jeffrey S.; Sekiyama, Thomas T.; Tanaka, Taichu Y.; Terradellas, Enric; Westphal, Douglas L.; Zhang, Xiao-Ye; Zhou, Chun-Hong

    2014-01-01

    Over the last few years, numerical prediction of dust aerosol concentration has become prominent at several research and operational weather centres due to growing interest from diverse stakeholders, such as solar energy plant managers, health professionals, aviation and military authorities and policymakers. Dust prediction in numerical weather prediction-type models faces a number of challenges owing to the complexity of the system. At the centre of the problem is the vast range of scales required to fully account for all of the physical processes related to dust. Another limiting factor is the paucity of suitable dust observations available for model, evaluation and assimilation. This chapter discusses in detail numerical prediction of dust with examples from systems that are currently providing dust forecasts in near real-time or are part of international efforts to establish daily provision of dust forecasts based on multi-model ensembles. The various models are introduced and described along with an overview on the importance of dust prediction activities and a historical perspective. Assimilation and evaluation aspects in dust prediction are also discussed.

  19. Continuous jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate

    Indian Academy of Sciences (India)

    B B Verma

    2009-12-01

    Plastic bags create a serious environmental problem. The proposed jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate may help to combat the war against this pollutant to certain extent. The paper laminate, without reinforcement fibre, exhibited a few fold superiority in tensile properties than single paper strip. The studies further show that an appreciable improvement in tensile properties can be achieved by introducing continuous jute fibre in paper laminates.

  20. Polymeric Optical Fibres for Biomedical Sensing

    OpenAIRE

    Krehel, M P

    2014-01-01

    In this thesis we focus on the integration of optical fibres in textiles to create wearable sensing systems. In the introduction (Chapter 3) we describe the basics of light guiding in optical fibres and methods of lateral light coupling. Subsequently, a literature review and motivation are presented. Afterwards two main parts can be differentiated. In the first one (Chapters 4, 5) a new method of continuous extrusion of optical fibres and their medical sensing application using photoplethysmo...

  1. THERMAL AND ENVIRONMENTAL EFFECTS ON CERAMIC FIBRES

    OpenAIRE

    Karlsson, S.; Lundberg, R.; Carlsson, R.

    1986-01-01

    Fibre insulations in kilns in the ceramic industry were investigated. Cristobalite and mullite are the main crystalline phases found in Al2O3-SiO2 fibres. The amount of the crystalline phases formed depends on the chemical composition and firing temperature. Condensation of ZnO-vapours from the glaze and formation of ZnAl2O4 were found in a Saffil fibre at a temperature of 930°C.

  2. A novel photonic crystal fibre switch

    DEFF Research Database (Denmark)

    Alkeskjold, Thomas Tanggaard; Hermann, D.S.; Broeng, Jes

    2003-01-01

    A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB.......A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB....

  3. Abaca fibre reinforced PP composites and comparison with jute and flax fibre PP composites

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available Abaca fibre reinforced PP composites were fabricated with different fibre loadings (20, 30, 40, 50wt% and in some cases 35 and 45 wt%. Flax and jute fibre reinforced PP composites were also fabricated with 30 wt% fibre loading. The mechanical properties, odour emission and structure properties were investigated for those composites. Tensile, flexural and Charpy impact strengths were found to increase for fibre loadings up to 40 wt% and then decreased. Falling weight impact tests were also carried out and the same tendency was observed. Owing to the addition of coupling agent (maleated polypropylene -MAH-PP, the tensile, flexural and falling weight impact properties were found to increase in between 30 to 80% for different fibre loadings. When comparing jute and flax fibre composites with abaca fibre composites, jute fibre composites provided best tensile properties but abaca fibre polypropylene composites were shown to provide best notch Charpy and falling weight impact properties. Odours released by flax fibre composites were smaller than jute and abaca fibre composites.

  4. A validation of the fibre orientation and fibre length attrition prediction for long fibre-reinforced thermoplastics

    Science.gov (United States)

    Hopmann, Ch.; Weber, M.; van Haag, J.; Schöngart, M.

    2015-05-01

    To improve the mechanical performance of polymeric parts, fibre reinforcement has established in industrial applications during the last decades. Next to the widely used Short Fibre-reinforced Thermoplastics (SFT) the use of Long Fibre-reinforced Thermoplastics (LFT) is increasingly growing. Especially for non-polar polymeric matrices like polypropylene (PP), longer fibres can significantly improve the mechanical performance. As with every kind of discontinuous fibre reinforcement the fibre orientations (FO) show a high impact on the mechanical properties. On the contrary to SFT where the local fibre length distribution (FLD) can be often neglected, for LFT the FLD show a high impact on the material's properties and has to be taken into account in equal measure to the FOD. Recently numerical models are available in commercial filling simulation software and allow predicting both the local FOD and FLD in LFT parts. The aim of this paper is to compare i.) the FOD results and ii) the FLD results from available orientation- and fibre length attrition-models to those obtained from experimental data. The investigations are conducted by the use of different injection moulded specimens made from long glass fibre reinforced PP. In order to determine the FOD, selected part sections are examined by means of Computed Tomographic (CT) analyses. The fully three dimensional measurement of the FOD is then performed by digital image processing using grey scale correlation. The FLD results are also obtained by using digital image processing after a thermal pyrolytic separation of the polymeric matrix from the fibres. Further the FOD and the FLD are predicted by using a reduced strain closure (RSC) as well as an anisotropic rotary diffusion - reduced strain closure model (ARD-RSC) and Phelps-Tucker fibre length attrition model implemented in the commercial filling software Moldflow, Autodesk Inc., San Rafael, CA, USA.

  5. A validation of the fibre orientation and fibre length attrition prediction for long fibre-reinforced thermoplastics

    Energy Technology Data Exchange (ETDEWEB)

    Hopmann, Ch.; Weber, M.; Haag, J. van; Schöngart, M. [Institute of Plastics Processing (IKV) at RWTH Aachen University, Pontstr. 49, 52062 Aachen (Germany)

    2015-05-22

    To improve the mechanical performance of polymeric parts, fibre reinforcement has established in industrial applications during the last decades. Next to the widely used Short Fibre-reinforced Thermoplastics (SFT) the use of Long Fibre-reinforced Thermoplastics (LFT) is increasingly growing. Especially for non-polar polymeric matrices like polypropylene (PP), longer fibres can significantly improve the mechanical performance. As with every kind of discontinuous fibre reinforcement the fibre orientations (FO) show a high impact on the mechanical properties. On the contrary to SFT where the local fibre length distribution (FLD) can be often neglected, for LFT the FLD show a high impact on the material’s properties and has to be taken into account in equal measure to the FOD. Recently numerical models are available in commercial filling simulation software and allow predicting both the local FOD and FLD in LFT parts. The aim of this paper is to compare i.) the FOD results and ii) the FLD results from available orientation- and fibre length attrition-models to those obtained from experimental data. The investigations are conducted by the use of different injection moulded specimens made from long glass fibre reinforced PP. In order to determine the FOD, selected part sections are examined by means of Computed Tomographic (CT) analyses. The fully three dimensional measurement of the FOD is then performed by digital image processing using grey scale correlation. The FLD results are also obtained by using digital image processing after a thermal pyrolytic separation of the polymeric matrix from the fibres. Further the FOD and the FLD are predicted by using a reduced strain closure (RSC) as well as an anisotropic rotary diffusion - reduced strain closure model (ARD-RSC) and Phelps-Tucker fibre length attrition model implemented in the commercial filling software Moldflow, Autodesk Inc., San Rafael, CA, USA.

  6. Surface treated polypropylene (PP) fibres for reinforced concrete

    Energy Technology Data Exchange (ETDEWEB)

    López-Buendía, Angel M., E-mail: buendia@uv.es [AIDICO Technological Institute of Construction, Benjamin Franklin 17, 46380 Paterna, Valencia (Spain); Romero-Sánchez, María Dolores [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain); Climent, Verónica [Lafarge Cementos, Polígono Sepes, Isaac Newton s/n, 46500 Sagunto, Valencia (Spain); Guillem, Celia [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain)

    2013-12-15

    Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

  7. Stone dusting process advance

    Energy Technology Data Exchange (ETDEWEB)

    Matt Ryan; David Humphreys [Mining Attachments (Qld.) Pty Ltd. (Australia)

    2009-01-15

    The coal mining industry has, for many years, used dry stone dust or calcium carbonate (CaCO{sub 3}) in the prevention of the propagation of coal dust explosions throughout their underground mines in Australia. In the last decade wet stone dusting has been introduced. This is where stone dust and water are mixed together to form a paste like slurry. This mixture is pumped and sprayed on to the underground roadway surfaces. This method solved the contamination of the intake airways but brought with it a new problem known as 'caking'. Caking is the hardened layer that is formed as the stone dust slurry dries. It was proven that this hardened layer compromises the dispersal characteristics of the stone dust and therefore its ability to suppress a coal dust explosion. This project set out to prove a specially formulated, non toxic slurry additive and process that could overcome the caking effect. The slurry additive process combines dry stone dust with water to form a slurry. The slurry is then treated with the additive and compressed air to create a highly vesicular foam like stone dusted surface. The initial testing on a range of additives and the effectiveness in minimising the caking effect of wet dusting were performed at Applied Chemical's research laboratory in Melbourne, Victoria and independently tested at the SGS laboratory in Paget, Queensland. The results from these tests provided the platform to conduct full scale spraying trials at the Queensland Mines Rescue Station and Caledon Coal's Cook Colliery, Blackwater. The project moved into the final stage of completion with the collection of data. The intent was to compare the slurry additive process to dry stone dusting in full-scale methane explosions at the CSIR Kloppersbos explosion facility in Kloppersbos, South Africa.

  8. Siliceous Fragments in Space Micro-dust: evidence for a New Class of Fossil

    Science.gov (United States)

    Miyake, N.; Wallis, M. K.; Al-Mufti, S.

    2011-10-01

    Collection of Interplanetary dust particles (IDPs) by stratospheric balloon-borne cryosamplers has shown in recent years has shown this to be a superior technique to collection by rockets and aircraft. IDPs in the Cardiff collection from 40km altitude have been studied via scanning electron microscopy and associated X-ray emissions. This paper reports the identification of IDPs containing carbonbaceous-siliceous fibres and whiskers, unlike the mineral silicate particles normally identified with astrophysical silicate. The integration in some cases into cometary agglomerate particles and coatins with salt and other components shows aggregation on the comet. Two examples of fibres have also been found in a carbonaceous chondrite (Tagish Lake) which is thought to have a cometary origin. The fibres and and whiskers may have formed in the comet environment, but their accumulation from the pre-solar dust cloud is not excluded. An astrophysical origin as high temperature condensate in stellar outflows does not however explain the fibre mophologies. We therefore suggest the fibres and whiskers are fragments of fossilized organisms, like some species of terrestrial diatoms.

  9. Electrical Characterization of Silicon Cores from Glass-Cladded Fibres

    OpenAIRE

    Lapointe, Kyle

    2014-01-01

    Semiconductor core fibres represent an emerging technology with potential applications in many areas, including photovoltaics and optical transmission. Recent advances in fibre manufacturing techniques has allowed long, continuous silicon core fibres to be produced in commercial draw towers. The effect of the molten core fibre fabrication method on the electrical properties of silicon cores from glass-clad fibres have been studied. Fibres with core diameters ranging from 60 to 300 µm wer...

  10. Postponed sowing does not alter the fibre/wood ratio or fibre extractability of fibre hemp (Cannabis sativa)

    NARCIS (Netherlands)

    Westerhuis, W.; Struik, P.C.; Dam, van J.E.G.; Stomph, T.J.

    2009-01-01

    Because hemp is a short-day plant, postponing the sowing date might be a suitable strategy to obtain shorter and smaller plants around flowering, when primary fibres are 'ripe' enough to be harvested. Smaller plants can be processed on existing flax scutching and hackling lines and might have fibre

  11. Simulation of complex phenomena in optical fibres

    Science.gov (United States)

    Allington-Smith, Jeremy; Murray, Graham; Lemke, Ulrike

    2012-12-01

    Optical fibres are essential for many types of highly multiplexed and precision spectroscopy. The success of the new generation of multifibre instruments under construction to investigate fundamental problems in cosmology, such as the nature of dark energy, requires accurate modellization of the fibre system to achieve their signal-to-noise ratio (SNR) goals. Despite their simple construction, fibres exhibit unexpected behaviour including non-conservation of etendue (focal ratio degradation, FRD) and modal noise. Furthermore, new fibre geometries (non-circular or tapered) have become available to improve the scrambling properties that, together with modal noise, limit the achievable SNR in precision spectroscopy. These issues have often been addressed by extensive tests on candidate fibres and their terminations, but these are difficult and time-consuming. Modelling by ray tracing and wave analysis is possible with commercial software packages, but these do not address the more complex features, in particular FRD. We use a phase-tracking ray-tracing method to provide a practical description of FRD derived from our previous experimental work on circular fibres and apply it to non-standard fibres. This allows the relationship between scrambling and FRD to be quantified for the first time. We find that scrambling primarily affects the shape of the near-field pattern but has negligible effect on the barycentre. FRD helps to homogenize the near-field pattern but does not make it completely uniform. Fibres with polygonal cross-section improve scrambling without amplifying the FRD. Elliptical fibres, in conjunction with tapering, may offer an efficient means of image slicing to improve the product of resolving power and throughput, but the result is sensitive to the details of illumination. We also investigated the performance of fibres close to the limiting numerical aperture since this may affect the uniformity of the SNR for some prime focus fibre instrumentation.

  12. Respirable dust measured downwind during rock dust application.

    Science.gov (United States)

    Harris, M L; Organiscak, J; Klima, S; Perera, I E

    2017-05-01

    The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

  13. Multicore optical fibre and fibre-optic delay line based on it

    Science.gov (United States)

    Egorova, O. N.; Astapovich, M. S.; Belkin, M. E.; Semjonov, S. L.

    2016-12-01

    The first switchable fibre-optic delay line based on a 1300-{\\text{m}}-long multicore optical fibre has been fabricated and investigated. We have obtained signal delay times of up to 45 \\unicode{956}{\\text{s}} at 6.43-\\unicode{956}{\\text{s}} intervals. Sequential signal propagation through the cores of the multicore optical fibre makes it possible to reduce the fibre length necessary for obtaining a predetermined delay time, which is important for reducing the weight and dimensions of devices based on the use of fibre-optic delay lines.

  14. Polarisation effects in twin-core fibre: Application for mode locking in a fibre laser

    Energy Technology Data Exchange (ETDEWEB)

    Lobach, I A; Kablukov, S I; Podivilov, Evgenii V; Babin, Sergei A; Apolonski, A A

    2012-09-30

    We report the first measurements of the longitudinal power distribution in a twin-core optical fibre at different input light polarisations. Experimental evidence is presented that, because of the difference in birefringence between the cores, the power in them depends on which core the beam is launched into. Experimental data are interpreted in terms of a modified polarisation model for mode coupling in twin-core fibres which takes into account the birefringence of the cores. In addition, we demonstrate for the first time the use of the polarisation properties of a twincore fibre for mode locking in a fibre laser. (optical fibres, lasers and amplifiers. properties and applications)

  15. Dust escape from Io

    Science.gov (United States)

    Flandes, Alberto

    2004-08-01

    The Dust ballerina skirt is a set of well defined streams composed of nanometric sized dust particles that escape from the Jovian system and may be accelerated up to >=200 km/s. The source of this dust is Jupiter's moon Io, the most volcanically active body in the Solar system. The escape of dust grains from Jupiter requires first the escape of these grains from Io. This work is basically devoted to explain this escape given that the driving of dust particles to great heights and later injection into the ionosphere of Io may give the particles an equilibrium potential that allow the magnetic field to accelerate them away from Io. The grain sizes obtained through this study match very well to the values required for the particles to escape from the Jovian system.

  16. Galactic dust properties

    Science.gov (United States)

    Paradis, D.

    2011-12-01

    Recent studies have shown evidence for variations in the dust emissivity law with temperature and wavelength. A recent dust emission model, called TLS model (for two-level systems), based on the description of the disordered internal structure of the amorphous dust grains has been developped to interpret observations in the far-infrared/submillimeter (FIR/submm) domain. A recent work focusing on the comparison between data of the diffuse interstellar medium seen by FIRAS-WMAP, as well as Archeops compact sources, with the TLS model allowed us to constrain the model parameters characterizing the general Galactic dust properties. Using the newly available Herschel/Hi-GAL data of the inner Galactic plane, we report a 500 μm emissivity excess in the peripheral parts of the Galactic plane, that can reach up to 20% of the emissivity. Results of the TLS modeling indicate significant changes in the dust properties from the central to peripheral parts of the Galactic plane.

  17. Investigation on effect of fibre hybridization and orientation on mechanical behaviour of natural fibre epoxy composite

    Indian Academy of Sciences (India)

    P KALIAPPAN; R KESAVAN; B VIJAYA RAMNATH

    2017-08-01

    Nowadays bio fibre composites play a vital role by replacing conventional materials used in automotive andaerospace industries owing to their high strength to weight ratio, biodegradability and ease of production. This paper aimsto find the effect of fibre hybridization and orientation on mechanical behaviour of composite fabricated with neem, abacafibres and epoxy resin. Here, three varieties of composites are fabricated namely, composite 1 which consists of abaca fibreand glass fibre, composite 2, which consists of neem fibre and glass fibre, whereas composite 3 consists of abaca, neem fibresand glass fibres. In all the above three varieties, fibres are arranged in three types of orientations namely, horizontal (type I),vertical (type II) and 45$^{\\circ}$ inclination (type III). The result shows that composites made up of abaca and neem fibres withinclined orientation (45$^{\\circ}$) have better mechanical properties when compared with other types of composites. In addition, morphological analysis is carried out using scanning electron microscope to know the fibre distribution, fibre pull out, fibre breakage and crack propagation on tested composites.

  18. Influence of fibre volume fraction and temperature on fatigue life of glass fibre reinforced plastics

    Directory of Open Access Journals (Sweden)

    Konrad Wegener

    2016-07-01

    Full Text Available The influence of fibre volume fraction and temperature on fatigue life of continuous glass fibre reinforced plastics is investigated in detail. The physical causes of the two effects on the slope of the S-N-curve in fibre direction at R = 0.1 are researched and can be explained with help of micrographs. A new phenomenological approach is presented to model both effects in fibre dominated laminates with different stacking sequences using only the static ultimate strength as an input. Static and fatigue tests of different layups and fibre volume fractions are performed at different temperatures to validate the fatigue life predictions. Additionally it is derived that there is an optimal fibre volume fraction regarding a minimum damage sum. This fibre volume fraction is dependent on a given loading spectra and can be calculated using the phenomenological model.

  19. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury, high value-added end of the market, notably the apparel market, being renowned for their special...

  20. low pump power photonic crystal fibre amplifiers

    DEFF Research Database (Denmark)

    Hougaard, Kristian G.; Broeng, Jes; Bjarklev, Anders Overgaard

    2003-01-01

    Designs of low pump power optical amplifiers, based on photonic crystal fibres are presented. The potential of these fibre amplifiers is investigated, and it is demonstrated that such amplifiers may deliver gains of more than 15 dB at 1550 nm with less than 1 mW of optical pump power....

  1. The development of fibre optic microbend sensors

    NARCIS (Netherlands)

    Horsthuis, W.H.G.; Fluitman, J.H.J.

    1983-01-01

    Investigations concerning the development of a fibre optic pressure sensor are reported. The phenomenon of light power attenuation in a periodically deformed graded index fibre has been studied theoretically. It appears that available theories are not suited to describe this attenuation process in t

  2. Multifunctional Carbon Fibre Tapes for Automotive Composites

    Science.gov (United States)

    Koncherry, V.; Potluri, P.; Fernando, A.

    2016-11-01

    Cabon fibre composites are used where mechanical performance such as strength, stiffness and impact properties at low density is a critical parameter for engineering applications. Carbon fibre flat tape is one material which is traditionally used to manufacture three-dimensional composites in this area. Modifying the carbon fibre tape to incorporate other functions such as stealth, electromagnetic interference, shielding, de-icing, self-repair, energy storage, allows us to create multi-functional carbon fibre tape. Researchers have been developing such material and the technology for their manufacture in order to produce multifunctional carbon fibre based components more economically and efficiently. This paper presents the manufacturing process of a metallised carbon fibre material for a chopped fibre preforming process that uses electromagnets for preforming instead of traditional suction airflow fibre deposition. In addition, the paper further presents mechanical and magneto-static modelling that is carried out to investigate the bending properties of the material produced and its suitability for creating 3D preforms.

  3. Dispersion properties of photonic Bandgap Fibres

    DEFF Research Database (Denmark)

    Broeng, Jes; Barkou, Stig Eigil; Søndergaard, Thomas

    1999-01-01

    Dispersion properties of new low-index core photonic crystal fibres are presented. Both wideband nearzero despersion and very large dispersion is shown possible in the 1550 nm wavelength range.......Dispersion properties of new low-index core photonic crystal fibres are presented. Both wideband nearzero despersion and very large dispersion is shown possible in the 1550 nm wavelength range....

  4. Selective filling of Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Noordegraaf, Danny; Sørensen, Thorkild

    2005-01-01

    A model for calculating the time necessary for filling one or more specific holes in a photonic crystal fibre is made. This model is verified for water, and its enabling potential is illustrated by a polymer application. Selective filling of the core in an air-guide photonic crystal fibre...

  5. Strength variability of single flax fibres

    DEFF Research Database (Denmark)

    Aslan, Mustafa; Chinga-Carrasco, G.; Sørensen, Bent F.

    2011-01-01

    (linear and nonlinear) of the fibres are found to be correlated with the amount of defects. The linear stress–strain curves tend to show a higher tensile strength, a higher Young’s modulus, and a lower strain to failure than the nonlinear curves. Finally, the fibres are found to fracture by a complex...

  6. Thermally induced structural changes in Nomex fibres

    Indian Academy of Sciences (India)

    Anjana Jain; Kalyani Vijayan

    2002-08-01

    Thermally aged Nomex fibres manifest several residual effects viz. reduction in X-ray crystallinity, weight loss and deterioration in tensile characteristics. Surface damages in the form of longitudinal openings, holes, material deposits etc have also been observed. Based on the data from thermally exposed fibres, the time needed for states of zero tensile strength and modulus have been predicted.

  7. Fibre optic cables for the ALICE experiment

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    These thin fibres will transmit the signal received in detectors at the ALICE experiment when it starts up with the LHC in 2008. The analogue signals produced in the detectors are first converted into digital pulse, which are transported in light down such fibres. Computers then read this digital signal to produce the final set of data.

  8. Cotton fibre cross-section properties

    Science.gov (United States)

    From a structural perspective the cotton fibre is a singularly discrete, elongated plant cell with no junctions or inter-cellular boundaries. Its form in nature is essentially unadulterated from the field to the spinning mill where its cross-section properties, as for any textile fibre, are central ...

  9. Fibre positioning algorithms for the WEAVE spectrograph

    NARCIS (Netherlands)

    Terrett, David L.; Lewis, Ian J.; Dalton, Gavin; Abrams, Don Carlos; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Middleton, Kevin; Trager, Scott C.

    2014-01-01

    WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. It is a multi-object "pick and place" fibre fed spectrograph with more than one thousand fibres, similar in concept to the Australian Astronomical Observ

  10. Winding of fibre composites; Vikling af fiberkompositter

    Energy Technology Data Exchange (ETDEWEB)

    Lystrup, Aage

    2006-01-01

    Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

  11. Selective filling of Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Noordegraaf, Danny; Sørensen, Thorkild

    2005-01-01

    A model for calculating the time necessary for filling one or more specific holes in a photonic crystal fibre is made. This model is verified for water, and its enabling potential is illustrated by a polymer application. Selective filling of the core in an air-guide photonic crystal fibre is demo...

  12. Development of the fibres of MOONS

    Science.gov (United States)

    Guinouard, Isabelle; Lee, David; Schnetler, Hermine; Taylor, William; Amans, Jean-Philippe; Montgomery, David; Oliva, Ernesto

    2014-07-01

    MOONS will exploit the full 500 square arcmin field of view offered by the Nasmyth focus of the Very Large Telescope and will be equipped with two identical triple arm cryogenic spectrographs covering the wavelength range 0.8 - 1.8 μm, with a multiplex capability of approximately 1000 fibres. Each triple arm spectrograph will produce spectra for half of the targets simultaneously. The system will have both a medium resolution (R~4000-6000) mode and a high resolution (R~20000) mode. The fibres are used to pick off each sub field of 1.05 arcseconds and are used to transport the light from the instrument focal plane to the two spectrographs. Each fibre has a microlens to focus the beam into the fibre at a relative fast focal ratio of F/3.65 to reduce the Focal Ratio Degradation (FRD). This paper presents the overall design of the fibre system and describes the specific developments required to optimise its performance. The design of the fibre input optics, the choice of the fibre connector, and the layout of the slit end are described. The results of preliminary tests to measure the effect of twisting on the FRD performance of prototype fibres are also discussed.

  13. Innovations with protein nano-fibres

    NARCIS (Netherlands)

    Linden, van der E.

    2006-01-01

    Proteins in solution can form objects of various shapes. One fascinating possibility is the formation of fibres with a length up to micrometers, but with a thickness of a few nanometers, therefore referring to them as nano-fibres. Many proteins show this behaviour under the appropriate conditions. G

  14. Winding of fibre composites; Vikling af fiberkompositter

    Energy Technology Data Exchange (ETDEWEB)

    Lystrup, Aage

    2006-01-01

    Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

  15. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Nielsen, Laila

    1997-01-01

    (capillary water uptake) is used, involving an in-situ method and a laboratory method. Three different concrete qualities as well as steel fibres (ZP) and polypropylene fibres (PP) are used. Results of the durability tests on cracked FRC-beams are compared to results for uncracked FRC-beams and beams without...

  16. Image analysis of insulation mineral fibres.

    Science.gov (United States)

    Talbot, H; Lee, T; Jeulin, D; Hanton, D; Hobbs, L W

    2000-12-01

    We present two methods for measuring the diameter and length of man-made vitreous fibres based on the automated image analysis of scanning electron microscopy images. The fibres we want to measure are used in materials such as glass wool, which in turn are used for thermal and acoustic insulation. The measurement of the diameters and lengths of these fibres is used by the glass wool industry for quality control purposes. To obtain reliable quality estimators, the measurement of several hundred images is necessary. These measurements are usually obtained manually by operators. Manual measurements, although reliable when performed by skilled operators, are slow due to the need for the operators to rest often to retain their ability to spot faint fibres on noisy backgrounds. Moreover, the task of measuring thousands of fibres every day, even with the help of semi-automated image analysis systems, is dull and repetitive. The need for an automated procedure which could replace manual measurements is quite real. For each of the two methods that we propose to accomplish this task, we present the sample preparation, the microscope setting and the image analysis algorithms used for the segmentation of the fibres and for their measurement. We also show how a statistical analysis of the results can alleviate most measurement biases, and how we can estimate the true distribution of fibre lengths by diameter class by measuring only the lengths of the fibres visible in the field of view.

  17. Interfaces between a fibre and its matrix

    Science.gov (United States)

    Lilholt, H.; Sørensen, B. F.

    2017-07-01

    The interface between a fibre and its matrix represents an important element in the characterization and exploitation of composite materials. Both theoretical models and analyses of experimental data have been presented in the literature since modern composite were developed and many experiments have been performed. A large volume of results for a wide range of composite systems exists, but rather little comparison and potential consistency have been reached for fibres and/or for matrices. Recently a materials mechanics approach has been presented to describe the interface by three parameters, the interfacial energy [J/m2], the interfacial frictional shear stress [MPa] and the mismatch strain [-] between fibre and matrix. The model has been used for the different modes of fibre pull-out and fibre fragmentation. In this paper it is demonstrated that the governing equations for the experimental parameters (applied load, debond length and relative fibre/matrix displacement) are rather similar for these test modes. A simplified analysis allows the direct determination of the three interface parameters from two plots for the experimental data. The complete analysis is demonstrated for steel fibres in polyester matrix. The analysis of existing experimental literature data is demonstrated for steel fibres in epoxy matrix and for tungsten wires in copper matrix. These latter incomplete analyses show that some results can be obtained even if all three experimental parameters are not recorded.

  18. Microstructural characterization of stone wool fibre network

    DEFF Research Database (Denmark)

    Chapelle, Lucie; Brøndsted, Povl; Kusano, Yukihiro;

    2014-01-01

    Understanding the mechanical properties of fibrous network as complex as stone wool materials requires a relevant description of their microstructure and architecture. In this study, different methods have been proposed to characterize the fibre orientation, diameter and length of fibres as well...

  19. Insertion of optic fibre for CMS

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    The MicroJET system uses high pressure to carefully put the optical fibres into their protective tubes. These fibres are vital for rapid data transfer, but are also very delicate and, if damanged, may not work at the required efficiency. Similiar methods are used to install cables for the telecommunications industry.

  20. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  1. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.;

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  2. Fibre Distribution in Friction-spun Yarns

    Institute of Scientific and Technical Information of China (English)

    Eric Oyondi Nganyi; YU Chong-wen

    2006-01-01

    According to the yarn forming characteristics in friction spinning, the arrangement of fed sliver is designed, to get the desired fiber distribution in the resultant yarn. On the base of that, the relation between the theoretical fibre distribution and the actual fibre distribution is analyzed by use of electron microscope.

  3. Metal-coated Bragg grating reflecting fibre

    Science.gov (United States)

    Chamorovskiy, Yu. K.; Butov, O. V.; Kolosovskiy, A. O.; Popov, S. M.; Voloshin, V. V.; Vorob'ev, I. L.; Vyatkin, M. Yu.

    2017-03-01

    High-temperature optical fibres (OF) with fibre Bragg gratings (FBG) arrays written over a long length and in-line metal coating have been made for the first time. The optical parameters of the FBG arrays were tested by the optical frequency domain reflectometer (OFDR) method in a wide temperature range, demonstrating no degradation in reflection at heating up to 600 °C for a fibre with Al coating. The mechanical strength of the developed fibre was practically the same as "ordinary" OF with similar coating, showing the absence of the influence of FBG writing process on fibre strength. Further experiments are necessary to evaluate the possibility of further increases in the operational temperature range.

  4. Simulation of complex phenomena in optical fibres

    CERN Document Server

    Allington-Smith, Jeremy; Lemke, Ulrike

    2012-01-01

    Optical fibres are essential for many types of highly-multiplexed and precision spectroscopy. The success of the new generation of multifibre instruments under construction to investigate fundamental problems in cosmology, such as the nature of dark energy, requires accurate modellisation of the fibre system to achieve their signal-to-noise goals. Despite their simple construction, fibres exhibit unexpected behaviour including non-conservation of Etendue (Focal Ratio Degradation; FRD) and modal noise. Furthermore, new fibre geometries (non-circular or tapered) have become available to improve the scrambling properties that, together with modal noise, limit the achievable SNR in precision spectroscopy. These issues have often been addressed by extensive tests on candidate fibres and their terminations but these are difficult and time-consuming. Modelling by ray-tracing and wave analysis is possible with commercial software packages but these do not address the more complex features, in particular FRD. We use a...

  5. Review article: dietary fibre-microbiota interactions.

    Science.gov (United States)

    Simpson, H L; Campbell, B J

    2015-07-01

    Application of modern rapid DNA sequencing technology has transformed our understanding of the gut microbiota. Diet, in particular plant-based fibre, appears critical in influencing the composition and metabolic activity of the microbiome, determining levels of short-chain fatty acids (SCFAs) important for intestinal health. To assess current epidemiological, experimental and clinical evidence of how long-term and short-term alterations in dietary fibre intake impact on the microbiome and metabolome. A Medline search including items 'intestinal microbiota', 'nutrition', 'diet', 'dietary fibre', 'SCFAs' and 'prebiotic effect' was performed. Studies found evidence of fibre-influenced differences in the microbiome and metabolome as a consequence of habitual diet, and of long-term or short-term intervention (in both animals and humans). Agrarian diets high in fruit/legume fibre are associated with greater microbial diversity and a predominance of Prevotella over Bacteroides. 'Western'-style diets, high in fat/sugar, low in fibre, decrease beneficial Firmicutes that metabolise dietary plant-derived polysaccharides to SCFAs and increase mucosa-associated Proteobacteria (including enteric pathogens). Short-term diets can also have major effects, particularly those exclusively animal-based, and those high-protein, low-fermentable carbohydrate/fibre 'weight-loss' diets, increasing the abundance of Bacteroides and lowering Firmicutes, with long-term adherence to such diets likely increasing risk of colonic disease. Interventions to prevent intestinal inflammation may be achieved with fermentable prebiotic fibres that enhance beneficial Bifidobacteria or with soluble fibres that block bacterial-epithelial adherence (contrabiotics). These mechanisms may explain many of the differences in microbiota associated with long-term ingestion of a diet rich in fruit and vegetable fibre. © 2015 The Authors. Alimentary Pharmacology & Therapeutics published by John Wiley & Sons Ltd.

  6. Effects of fibre content on mechanical properties and fracture behaviour of short carbon fibre reinforced geopolymer matrix composites

    Indian Academy of Sciences (India)

    Tiesong Lin; Dechang Jia; Meirong Wang; Peigang He; Defu Liang

    2009-02-01

    Geopolymer matrix composites reinforced with different volume fractions of short carbon fibres (Cf/geopolymer composites) were prepared and the mechanical properties, fracture behaviour and microstructure of as-prepared composites were studied and correlated with fibre content. The results show that short carbon fibres have a great strengthening and toughening effect at low volume percentages of fibres (3.5 and 4.5 vol.%). With the increase of fibre content, the strengthening and toughening effect of short carbon fibres reduce, possibly due to fibre damage, formation of high shear stresses at intersect between fibres and strong interface cohesion of fibre/matrix under higher forming pressure. The property improvements are primarily based on the network structure of short carbon fibre preform and the predominant strengthening and toughening mechanisms are attributed to the apparent fibre bridging and pulling-out effect.

  7. Knowledge about dietary fibre: a fibre study framework.

    Science.gov (United States)

    Guiné, Raquel P F; Ferreira, Manuela; Correia, Paula; Duarte, João; Leal, Marcela; Rumbak, Ivana; Barić, Irena C; Komes, Drazenka; Satalić, Zvonimir; Sarić, Marijana M; Tarcea, Monica; Fazakas, Zita; Jovanoska, Dijana; Vanevski, Dragoljub; Vittadini, Elena; Pellegrini, Nicoletta; Szűcs, Viktória; Harangozó, Júlia; El-Kenawy, Ayman; El-Shenawy, Omnia; Yalçın, Erkan; Kösemeci, Cem; Klava, Dace; Straumite, Evita

    2016-09-01

    The objective of this work was to study the degree of knowledge about dietary fibre (DF), as influenced by factors such as gender, level of education, living environment or country. For this, a descriptive cross-sectional study was undertaken on a non-probabilistic sample of 6010 participants from 10 countries in different continents (Europe, Africa and America). The results showed that the participants revealed on average a positive but still low global level of knowledge, which alerts for the need to take some actions to further inform the population about DF and its role as a component of a healthy diet. The results also indicated differences between genders, levels of education, living environments and countries. The highest level of knowledge was revealed by the participants from female gender, with higher education and living in urban areas. Concerning the country, the best informed were the participants from Romania, followed by those from Portugal and Turkey while the least informed were from Egypt.

  8. Comparison of Acoustic Characteristics of Date Palm Fibre and Oil Palm Fibre

    Directory of Open Access Journals (Sweden)

    Lamyaa Abd ALRahman

    2014-02-01

    Full Text Available This study investigated and compared the acoustic characteristics of two natural organic fibres: date palm fibre and oil palm fibre, these materials eligible for acoustical absorption. During the processing stage, both fibre sheets are treated with latex. The two fibres are compressed after latex treatment Circular samples (100 mm in diameter and 28 mm, based on the measurement tube requirements are cut out of the sheets. The density of the date palm fibre sheet is 150 kg/m3 for a 50 mm thickness and 130 kg/m3 for a 30 mm thickness. In contrast, the density of oil palm fibre is 75 kg/m3 for a 50 mm thickness and 65 kg/m3 for a 30 mm thickness. An impedance tube was used to test the thicknesses of both samples based on international standards. The results show that the date palm fibre exhibits two Acoustic Absorption Coefficient (AAC peaks: 0.93 at 1356 Hz and 0.99 at 4200-4353 Hz for the 50-mm-thick sample. In contrast, the 30-mm-thick sample has a single AAC peak of 0.83 at 2381.38-2809.38 Hz. However, the 50-mm-thick oil palm fibre has an AAC peak of 0.75 at 1946.88-2178.13 Hz and the 30-mm-thick oil palm fibre has an acoustic absorption coefficient peak 0.59 at 3225-3712.5 Hz. Thus, the date palm fibre has a higher acoustic absorption coefficient for high and low frequencies than does oil palm fibre. Both fibres are promising for use as sound absorber materials to protect against environmental noise pollution.

  9. Mechanisms of metal dusting corrosion

    DEFF Research Database (Denmark)

    Hummelshøj, Thomas Strabo

    In this thesis the early stages of metal dusting corrosion is addressed; the development of carbon expanded austenite, C, and the decomposition hereof into carbides. Later stages of metal dusting corrosion are explored by a systematic study of stainless steel foils exposed to metal dusting...... influence of oxygen and carbon on the metal dusting corrosion is explored. The results indicate that exposure to metal dusting conditions have a detrimental effect on the resistance against oxidation and, conversely, that exposure to oxidation has a detrimental effect on the resistance towards metal dusting....... Consequently, a combination of carburizing and oxidizing conditions has a strong mutual catalyzing effect on the metal dusting corrosion....

  10. Composite circumstellar dust grains

    Science.gov (United States)

    Gupta, Ranjan; Vaidya, Dipak B.; Dutta, Rajeshwari

    2016-10-01

    We calculate the absorption efficiencies of composite silicate grains with inclusions of graphite and silicon carbide in the spectral range 5-25 μm. We study the variation in absorption profiles with volume fractions of inclusions. In particular we study the variation in the wavelength of peak absorption at 10 and 18 μm. We also study the variation of the absorption of porous silicate grains. We use the absorption efficiencies to calculate the infrared flux at various dust temperatures and compare with the observed infrared emission flux from the circumstellar dust around some M-type and asymptotic giant branch stars obtained from IRAS and a few stars from Spitzer satellite. We interpret the observed data in terms of the circumstellar dust grain sizes, shape, composition and dust temperature.

  11. Composite Circumstellar Dust Grains

    CERN Document Server

    Gupta, Ranjan; Dutta, Rajeshwari

    2016-01-01

    We calculate the absorption efficiencies of composite silicate grains with inclusions of graphite and silicon carbide in the spectral range 5--25$\\rm \\mu m$. We study the variation in absorption profiles with volume fractions of inclusions. In particular we study the variation in the wavelength of peak absorption at 10 and 18$\\rm \\mu m$. We also study the variation of the absorption of porous silicate grains. We use the absorption efficiencies to calculate the infrared flux at various dust temperatures and compare with the observed infrared emission flux from the circumstellar dust around some M-Type \\& AGB stars obtained from IRAS and a few stars from Spitzer satellite. We interpret the observed data in terms of the circumstellar dust grain sizes; shape; composition and dust temperature.

  12. Nano Dust Analyzer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a new highly sensitive instrument to confirm the existence of the so-called nano-dust particles, characterize their impact parameters, and...

  13. Ductility Performance of Hybrid Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    S. Eswari

    2008-01-01

    Full Text Available This study presents a study on the ductility performance of hybrid fibre reinforced concrete. The influence of fibre content on the ductility performance of hybrid fibre reinforced concrete specimens having different fibre volume fractions was investigated. The parameters of investigation included modulus of rupture, ultimate load, service load, ultimate and service load deflection, crack width, energy ductility and deflection ductility. A total of 27 specimens, 100×100×500 mm, were tested to study the above parameters. The specimens incorporated 0.0 to 2.0% volume fraction of polyolefin and steel fibres in different proportions. The ductility performance of hybrid fibre reinforced concrete specimens was compared with that of plain concrete. The test results show that addition of 2.0% by volume of hybrid fibres improves the ductility performance appreciably. An adaptive Neuro-Fuzzy based model has been proposed to predict the ductility performance characteristics. A reasonably close agreement has been obtained between the experimental and predicted results.

  14. Controllable spatiotemporal nonlinear effects in multimode fibres

    Science.gov (United States)

    Wright, Logan G.; Christodoulides, Demetrios N.; Wise, Frank W.

    2015-05-01

    Multimode fibres are of interest for next-generation telecommunications systems and the construction of high-energy fibre lasers. However, relatively little work has explored nonlinear pulse propagation in multimode fibres. Here, we consider highly nonlinear ultrashort pulse propagation in the anomalous-dispersion regime of a graded-index multimode fibre. Low modal dispersion and strong nonlinear coupling between the fibre's many spatial modes result in interesting behaviour. We observe spatiotemporal effects reminiscent of nonlinear optics in bulk media—self-focusing and multiple filamentation—at a fraction of the usual power. By adjusting the spatial initial conditions, we generate on-demand, megawatt, ultrashort pulses tunable between 1,550 and 2,200 nm dispersive waves over one octave; intense combs of visible light; and a multi-octave-spanning supercontinuum. Our results indicate that multimode fibres present unique opportunities for observing new spatiotemporal dynamics and phenomena. They also enable the realization of a new type of tunable, broadband fibre source that could be useful for many applications.

  15. Ceramic fibres for the automotive industry

    Energy Technology Data Exchange (ETDEWEB)

    Fryatt, J.

    1985-01-01

    The outstanding thermal, physical and chemical properties of ceramic fibres make them a noticeable contender for inclusion in engineered systems to satisfy such performance demands. A wide range of fibres and fibre-based products are available which exhibit such characteristics as high temperature continuous service ability (1600/sup 0/C if required), low thermal conductivity, excellent resistance to chemical attack (including reducing conditions), good acoustic performance at all temperatures and good resistance to vibration. They are also lightweight, fireproof and incombustible. Ceramic fibres should really be referred to as refractory fibres as they are based on combinations of high purity alumina and silica. Two groups of products exist. The most common have a continuous-use temperature of 1260/sup 0/C. These fibres are characterized by an alumina content of 40-50% but refractoriness and temperature use limit can be increased to about 1400/sup 0/C by modifying the basic chemistry. This generally involves increasing the alumina content to as much as 62% or adding chromia or zirconia to the basic mix. The second and less common group of fibres is characterized by both chemistry and crystal morphology. Chemistry is biased towards a high alumina content (over 70%), while production routes are designed to yield as high a crystal phase (and so enhanced high temperature stability) as possible.

  16. Comparison of two novel approaches to model fibre reinforced concrete

    NARCIS (Netherlands)

    Radtke, F.K.F.; Simone, A.; Sluys, L.J.

    2009-01-01

    We present two approaches to model fibre reinforced concrete. In both approaches, discrete fibre distributions and the behaviour of the fibre-matrix interface are explicitly considered. One approach employs the reaction forces from fibre to matrix while the other is based on the partition of unity f

  17. Coherent Beam Combination of Two Polarization Maintaining Ytterbium Fibre Amplifiers

    Institute of Scientific and Technical Information of China (English)

    HOU Jing; XIAO Rui; JIANG Zong-Fu; CHENG Xiang-Ai; SHU Bai-Hong; CHEN Jin-Bao; LIU Ze-Jin

    2005-01-01

    @@ We investigate coherent beam combination of fibre laser beams by phase locking. Phase noise of a polarization maintaining ytterbium fibre amplifier is inspected with a fibre interferometer. In a feed back control loop, two fibre polarization maintaining ytterbium amplifiers are phase locked and coherent combined when the phase noise is properly controlled by a LiNO3 phase modulator.

  18. Dust Versus Cosmic Acceleration

    CERN Document Server

    Aguirre, A N

    1999-01-01

    Two groups have recently discovered a statistically significant deviation in the fluxes of high-redshift type Ia supernovae from the predictions of a Friedmann model with zero cosmological constant. This letter argues that bright, dusty, starburst galaxies would preferentially eject a dust component with a shallower opacity curve (hence less reddening) and a higher opacity/mass than the observed galactic dust which is left behind. Such dust could cause the falloff in flux at high-z without violating constraints on reddening or metallicity. The specific model presented is of needle-like dust, which is expected from the theory of crystal growth and has been detected in samples of interstellar dust. Carbon needles with conservative properties can supply the necessary opacity, and would very likely be ejected from galaxies as required. The model is not subject to the arguments given in the literature against grey dust, but may be constrained by future data from supernova searches done at higher redshift, in clust...

  19. Nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch

    . The combination of a small core size and zero-dispersion wavelength at the operating wavelength of widely available femtosecond Ti:sapphire lasers led to an extensive research in supercontinuum generation and other nonlinear effects in PCFs. It is crucial for the efficiency of many nonlinear mechanisms...... that the pump laser wavelength is close to the zero-dispersion wavelength and that the core size is small. Recently, work in fabricating PCFs from materials other than silica has intensified. One of the advantages of using alternative materials can be a higher inherent material nonlinearity, which...... to accurately obtain a small core size while maintaining small structural variations during fibre drawing. This talk will give a presentation of how the mPOFs are fabricated and the route to obtaining nonlinear effects in them....

  20. A Study in Physical and Mechanical Properties of Hemp Fibres

    Directory of Open Access Journals (Sweden)

    Asim Shahzad

    2013-01-01

    Full Text Available This paper presents the results of the experiments undertaken to evaluate various physical and mechanical properties of hemp fibres. The study of these properties is vital for comparison with similar properties of synthetic fibres and for assessing hemp fibres’ suitability for use as reinforcement in composite materials. The properties of hemp fibres were found to be good enough to be used as reinforcement in composite materials. However, the issues of relatively high moisture content of fibres, variability in fibre properties, and relatively poor fibre/matrix interfacial strength were identified as factors that can reduce the efficiency with which these fibres can be utilised.

  1. Radiation tolerance tests of scintillating fibres

    Energy Technology Data Exchange (ETDEWEB)

    Gavardi, Laura; Albrecht, Johannes [TU Dortmund (Germany); Collaboration: LHCb-Collaboration

    2016-07-01

    An upgrade of the LHCb detector is planned during the shutdown which will take place from mid 2018 to the end of 2019. The proposed upgrade for the tracking system is a detector composed of scintillating fibres read out by silicon photomultipliers. The tracking detector will be working in an environment exposed to radiation, so that the resistance of the fibres to radiation is an important quality, which needs to be investigated. In this talk tests of scintillating fibres tolerance to radiation will be presented.

  2. Analysing the nanoporous structure of aramid fibres

    DEFF Research Database (Denmark)

    Pauw, Brian Richard; Vigild, Martin Etchells; Mortensen, Kell;

    2010-01-01

    After consideration of the applicability of classical methods, a novel analysis method for the characterization of fibre void structures is presented, capable of fitting the entire anisotropic two-dimensional scattering pattern to a model of perfectly aligned, polydisperse ellipsoids. It is tested...... for validity against the computed scattering pattern for a simulated nanostructure, after which it is used to fit the scattering from the void structure of commercially available heat-treated poly(p-phenylene terephtalamide) fibre and its as-spun precursor fibre. The application shows a reasonable fit...

  3. Silica holey fibres: fabrication and nonlinear effects

    OpenAIRE

    Belardi, W.; Monro, T.M.; Lee, J.H.; Yusoff, Z.; Price, J.H.V.; Malinowski, A.; Piper, A; Richardson, D J

    2002-01-01

    Holey fibres (HFs) [1] have emerged as a novel class of optical fibres which can provide completely new optical properties, such as endlessly single mode operation and novel dispersion properties as anomalous dispersion below 1.3µm, broadband flat dispersion and highly normal dispersion at 1.55µm. Moreover by changing the HF parameters (i.e. hole and core size), it is possible to fabricate HFs with an effective area so high as 800µm2 or so low as approximately 1µm2 [2]. A holey fibre perform ...

  4. Fibre Optic Protection System for Concrete Structures

    Institute of Scientific and Technical Information of China (English)

    J.S.Leng; A.Hameed; D.Winter; R.A.Barnes; G.C.Mays; G.F.Fernando

    2006-01-01

    The design concepts, modelling and implementation of various fibre optic sensor protection systems for development in concrete structures were investigated. Design concepts and on-site requirements for surface-mounted and embedded optical fibre sensor in concrete were addressed. Finite element (FE) modelling of selected sensor protection systems in strain-transfer efficiency from the structure to the sensing region was also studied. And experimental validation of specified sensor protection system was reported. Results obtained indicate that the protection system for the sensors performs adequately in concrete environment and there is very good correlation between results obtained by the protected fibre optic sensors and conventional electrical resistance strain gauges.

  5. Fibre optic power meter calibration uncertainties

    CSIR Research Space (South Africa)

    Nel, M

    2010-06-01

    Full Text Available thereof. It was done only for standard single mode fibre with FC (ferrule connector) connectors, and using a 1310 and a 1550 nm Fabry Perot laser (FP laser). The calibration set-up and procedure The uncertainty contributions for fibre optic power..., in this case 1310 or 1550 nm, is fed to the fibre optic power meter (secondary standard or unit under test (UUT)) via an attenuator. The attenuator serves to reduce back-reflections into the source and to set the power to the desired level. In Fig. 1...

  6. Newton to Einstein — dust to dust

    Energy Technology Data Exchange (ETDEWEB)

    Kopp, Michael; Uhlemann, Cora; Haugg, Thomas, E-mail: michael.kopp@physik.lmu.de, E-mail: cora.uhlemann@physik.lmu.de, E-mail: thomas.haugg@physik.lmu.de [Arnold Sommerfeld Center for Theoretical Physics, Ludwig-Maximilian University Munich, Theresienstr. 37, Munich, 80333 (Germany)

    2014-03-01

    We investigate the relation between the standard Newtonian equations for a pressureless fluid (dust) and the Einstein equations in a double expansion in small scales and small metric perturbations. We find that parts of the Einstein equations can be rewritten as a closed system of two coupled differential equations for the scalar and transverse vector metric perturbations in Poisson gauge. It is then shown that this system is equivalent to the Newtonian system of continuity and Euler equations. Brustein and Riotto (2011) conjectured the equivalence of these systems in the special case where vector perturbations were neglected. We show that this approach does not lead to the Euler equation but to a physically different one with large deviations already in the 1-loop power spectrum. We show that it is also possible to consistently set to zero the vector perturbations which strongly constrains the allowed initial conditions, in particular excluding Gaussian ones such that inclusion of vector perturbations is inevitable in the cosmological context. In addition we derive nonlinear equations for the gravitational slip and tensor perturbations, thereby extending Newtonian gravity of a dust fluid to account for nonlinear light propagation effects and dust-induced gravitational waves.

  7. The coupling performance of photonic crystal fibres in fibre stellar interferometry

    DEFF Research Database (Denmark)

    Corbett, J.; Dabirian, A.; Butterley, T.;

    2006-01-01

    Large mode area (LMA), single-mode photonic crystal fibres (PCFs) have the potential to provide significant instrumental advantages in fibre stellar interferometry, due to their broadband attenuation spectrum, endlessly single-moded performance and very large core size. We investigate the theoret......Large mode area (LMA), single-mode photonic crystal fibres (PCFs) have the potential to provide significant instrumental advantages in fibre stellar interferometry, due to their broadband attenuation spectrum, endlessly single-moded performance and very large core size. We investigate...... the theoretical performance of coupling the telescope point spread function directly into LMA PCFs. We find that a single LMA fibre can replace as many as three step-index fibres for atmospheric seeing characterized by D-T/r(o) >= 2 with approximately the same coupling performance and a slower feed from...

  8. Rare-Earth Doped Photonic Crystal Fibre Lasers and Amplifiers

    DEFF Research Database (Denmark)

    Hougaard, Kristian G.

    2005-01-01

    In this thesis, a theoretical and numerical study of the use of rare-earthdoped photonic crystal fibres as optical amplifiers and lasers, has been performed. Photonic crystal fibres or microstructured optical fibres is a new kind of optical fibre in which the cladding region typically consist...... of a periodic microstructure, resulting in a fibre with very different properties compared to conventional optical fibres. The properties of photonic crystals fibres are described, with focus on the advantages this technology provides compared to conventional fibres, within the area of optical amplification....... The thesis also presents the basic properties of optical amplification, and describes the numerical model developed to model the behaviour of lasers and amplifiers based on photonic crystal fibres. The developed numerical tools are then used to investigate specific applications of photonic crystal fibres...

  9. Methodology for characterisation of glass fibre composite architecture

    DEFF Research Database (Denmark)

    Hansen, Jens Zangenberg; Larsen, J.B.; Østergaard, R.C.

    2012-01-01

    of the fibres. The information is used for different analyses to investigate and characterise the fibre architecture. As an example, the methodology is applied to glass fibre reinforced composites with varying fibre contents. The different fibre volume fractions (FVFs) affect the number of contact points per......The present study outlines a methodology for microstructural characterisation of fibre reinforced composites containing circular fibres. Digital micrographs of polished cross-sections are used as input to a numerical image processing tool that determines spatial mapping and radii detection...... fibre, the communal fibre distance and the local FVF. The fibre diameter distribution and packing pattern remain somewhat similar for the considered materials. The methodology is a step towards a better understanding of the composite microstructure and can be used to evaluate the interconnection between...

  10. A temperature-independent fibre-optic magnetic-field sensor using thin-core fibre tailored fibre Bragg grating

    Science.gov (United States)

    Tian, Qin; Feng, Zhongyao; Rong, Qiangzhou; Wan, Yun; Qiao, Xueguang; Hu, Manli; Yang, Hangzhou; Wang, Ruohui; Shao, Zhihua; Yang, Tingting

    2017-06-01

    A temperature-independent fibre-optic magnetic-field sensor is proposed and demonstrated experimentally. The device consists of a thin-core fibre (TCF) sandwiched in the upstream of a fibre Bragg grating (FBG). Because of the core-mismatch between the TCF and the single-mode fibre (SMF), the core mode is coupled to the cladding modes within the TCF cladding, and parts of them are recoupled back to the leading-in SMF by the downstream FBG. The cladding modes are sensitive to the ambient refractive index (RI), and therefore have the ability to respond to a RI change in the magnetic fluid determined by the ambient magnetic field. The intensities of the cladding-mode resonances are highly sensitive to the magnetic field change, while, in contrast, the resonance wavelengths always remain unchanged. This property can allow the sensor to act as a power-referenced reflection probe for magnetic field measurements.

  11. Polymerizing the fibre between bacteria and host cells: the biogenesis of functional amyloid fibres

    OpenAIRE

    2008-01-01

    Amyloid fibres are proteinaceous aggregates associated with several human diseases, including Alzheimer’s, Huntington’s and Creutzfeldt Jakob’s. Disease-associated amyloid formation is the result of proteins that misfold and aggregate into β sheet-rich fibre polymers. Cellular toxicity is readily associated with amyloidogenesis, although the molecular mechanism of toxicity remains unknown. Recently, a new class of ‘functional’ amyloid fibres was discovered that demonstrates that amyloids can ...

  12. Device for the collection of radio-active materials in the form of dust or powder

    Energy Technology Data Exchange (ETDEWEB)

    Hellriegel, W.

    1980-05-14

    The dust contaminated with radio-activity formed when drilling cement and concrete is sucked in by suction plant via a line into a closed container. The container itself stands in a barrel with or without concrete shielding. The suction plant produces the subpressure in the container via a suction line. This is fixed on the lid of the container and has a filter at its suction opening inside the container. The filter consists of several fibre air-filter mats, which are arranged inside the filter housing at an angle to the air and dust flow and displaced relative to each other.

  13. Simulation of dust production in ITER transient events

    Energy Technology Data Exchange (ETDEWEB)

    Pestchanyi, S. [Forschungszentrum Karlsruhe (Germany)

    2007-07-01

    The tritium retention problem is a critical issue for the tokamak ITER performance. Tritium is trapped in redeposited T-C layers and at the surface of carbon dust, where it is retained in form of various hydrocarbons. The area of dust surface and hence, the amount of tritium deposited on the surface depends on the dust amount and of the dust sizes. The carbon dust appears as a result of brittle destruction at the surface of the carbon fibre composite (CFC) which is now the reference armour material for the most loaded part of tokamak divertor. Stationary heat flux on the ITER divertor armour does not cause its brittle destruction and does not produce dust. However, according to the modern understanding of tokamak fusion devices performance, the most attractive regime of ITER operation is the ELMy H mode. This regime is associated with a repetitive short time increase of heat flux at the CFC divertor armour of 2-3 orders of magnitude over its stationary value during edge localized modes (ELMs). Under influence of these severe heat shocks CFC armour can crack due to the thermostress, producing a dust of carbon. Besides, a carbon dust produced during disruptions due to brittle destruction of the armour under influence of thermoshock. Most of the modern tokamaks do not produce the ELMs powerful enough to cause CFC brittle destruction at the divertor surface, except of very special regimes in JET. This is why the CFC erosion and dust production could be investigated now only theoretically and experimentally in plasma guns and electron beam facilities. Simulation of the CFC brittle destruction has been done using the code PEGASUS already developed and tested in FZK for simulation of erosion for ITER candidate materials under the heat shocks. After upgrades the code was used for simulation of the amount of carbon dust particles and of the distribution of their sizes. The code has been tested against available experimental data from the plasma gun MK-200UG and from the

  14. Strength Evaluation of Steel-Nylon Hybrid Fibre Reinforced Concrete

    OpenAIRE

    Maniram Kumar; Er. Ankush Khadwal

    2014-01-01

    When fibres like steel, glass, polypropylene, nylon, carbon, aramid, polyester, jute, etc are mixed with concrete known as fibre reinforced concrete. To overcome the deficiencies of concrete; fibres are added to improve the performance of concrete. In this research hybrid reinforced concrete is made by using steel and nylon 6 fibres. The inclusion of both steel and nylon 6 fibres are used in order to combine the benefits of both fibers; structural improvements provided by stee...

  15. Synchronously pumped picosecond all-fibre Raman laser based on phosphorus-doped silica fibre.

    Science.gov (United States)

    Kobtsev, Sergey; Kukarin, Sergey; Kokhanovskiy, Alexey

    2015-07-13

    Reported for the first time is picosecond-range pulse generation in an all-fibre Raman laser based on P₂O₅-doped silica fibre. Employment of phosphor-silicate fibre made possible single-cascade spectral transformation of pumping pulses at 1084 nm into 270-ps long Raman laser pulses at 1270 nm. The highest observed fraction of the Stokes component radiation at 1270 nm in the total output of the Raman laser amounted to 30%. The identified optimal duration of the input pulses at which the amount of Stokes component radiation in a ~16-m long phosphorus-based Raman fibre converter reaches its maximum was 140-180 ps.

  16. Polarisation effects in twin-core fibre: Application for mode locking in a fibre laser

    Science.gov (United States)

    Lobach, I. A.; Kablukov, S. I.; Podivilov, Evgenii V.; Babin, Sergei A.; Apolonski, A. A.

    2012-09-01

    We report the first measurements of the longitudinal power distribution in a twin-core optical fibre at different input light polarisations. Experimental evidence is presented that, because of the difference in birefringence between the cores, the power in them depends on which core the beam is launched into. Experimental data are interpreted in terms of a modified polarisation model for mode coupling in twin-core fibres which takes into account the birefringence of the cores. In addition, we demonstrate for the first time the use of the polarisation properties of a twincore fibre for mode locking in a fibre laser.

  17. Yb3+-Doped Double-Clad Fibre Laser Based on Fibre Bragg Grating

    Institute of Scientific and Technical Information of China (English)

    范万德; 付圣贵; 张强; 宁鼎; 李丽君; 王志; 袁树忠; 董孝义

    2003-01-01

    A novel Yb3+-doped double-clad fibre laser based on a double-clad fibre Bragg grating is presented. The fibre Bragg grating, as the output mirror, has been formed in Yb3+-doped double-clad fibre with the phase-mask method. When the input pump power is 2.8 W, the maximum laser output power is 570mW, with < 0.2 nm in line-width at the wavelength of 1.058μm, over 40dB signal-to-noise ratio and 24% slope efficiency.

  18. ELASTICITY of SHORT FIBRE REINFORCED POLYAMIDE: MORPHOLOGICAL AND NUMERICAl ANALYSIS OF FIBRE ORIENTATION EFFECTS

    Directory of Open Access Journals (Sweden)

    Francesca Cosmi

    2010-10-01

    Full Text Available The fatigue behaviour of injection moulded short fibre reinforced polymers depends upon fibre orientation, as shown in experiments conducted with notched specimens injected through different injection gates. The different fatigue behaviour is mainly related to the different local elastic properties, as determined by the different fibre orientation patterns, resulting into different strain distributions. In order to quantify the relationship between fibre orientation and elastic constants, the Cell Method was applied to volumes extracted from the specimens, reconstructed by micro-tomography.

  19. Individual fibre segmentation from 3D X-ray computed tomography for characterising the fibre orientation in unidirectional composite materials

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Jespersen, Kristine Munk; Dahl, Anders Bjorholm

    2017-01-01

    The aim of this paper is to characterise the fibre orientation in unidirectional fibre reinforced polymers, namely glass and carbon fibre composites. The compression strength of the composite is related to the orientation of the fibres. Thus the orientation is essential when designing materials...... for wind turbine blades. The calculation of the fibre orientation distribution is based on segmenting the individual fibres from volumes that have been acquired through X-ray tomography. The segmentation method presented in this study can accurately extract individual fibres from low contrast X-ray scans...... of composites with high fibre volume fraction. From the individual fibre orientations, it is possible to obtain results which are independent of the scanning quality. The compression strength for both composites is estimated from the average fibre orientations and is found to be of the same order of magnitude...

  20. Design Methods for Fibre Reinforced Concrete

    DEFF Research Database (Denmark)

    Stang, Henrik

    1996-01-01

    The present paper describes the outline of a research project on Fibre Reinforced Concrete (FRC) currently being carried out in Denmark under the supervision of Danish Council of Technology, Danish Technical Research Council and Danish Natural Science Research Counsil....

  1. Optical fibres bringing the LHC into focus

    CERN Multimedia

    2003-01-01

    New components are being added to CERN's optical fibre network, which will transport the torrents of data produced by the LHC. 1500 kilometres of cables will be installed in the tunnels and at ground level.

  2. Chinese Market for Fibres and Cables

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    This article presents a summary of Chinese market of optical fibres and cables based on the development of the optical communications industry. Analysis shows that the market will keep growing for sometime in the future.

  3. Flatus emission patterns and fibre intake.

    Science.gov (United States)

    Bolin, T D; Stanton, R A

    1998-01-01

    Knowledge of the normal range of flatus emissions and their relationship to diet, particularly fibre, would be helpful in managing patients who complain of excessive flatus or abdominal distention. Sixty men and 60 women aged between 17 and 67 kept a three-day daily record, including one week-end day, of their flatus emissions, dietary fibre intake and beer consumption. Daily flatus emissions averaged 12.7 (range to 2-53) for men and 7.1 (range 1-32) for women. Fibre intake averaged 28+/-13 g for men and 24+/-3 g for women. Flatus emissions significantly correlated with dietary fibre intake (pflatus emissions and beer intake in men and men recorded more aromatic flatus than women. This study of 120 normal individuals eating their choice of foods provides a basis to judge degrees of abnormality in patients complaining of excessive flatus.

  4. Optical Fibre Pressure Sensors in Medical Applications

    Directory of Open Access Journals (Sweden)

    Sven Poeggel

    2015-07-01

    Full Text Available This article is focused on reviewing the current state-of-the-art of optical fibre pressure sensors for medical applications. Optical fibres have inherent advantages due to their small size, immunity to electromagnetic interferences and their suitability for remote monitoring and multiplexing. The small dimensions of optical fibre-based pressure sensors, together with being lightweight and flexible, mean that they are minimally invasive for many medical applications and, thus, particularly suited to in vivo measurement. This means that the sensor can be placed directly inside a patient, e.g., for urodynamic and cardiovascular assessment. This paper presents an overview of the recent developments in optical fibre-based pressure measurements with particular reference to these application areas.

  5. Central Tracking Detector Based on Scintillating Fibres

    CERN Multimedia

    2002-01-01

    Scintillating fibres form a reasonable compromise for central tracking detectors in terms of price, resolution, response time, occupancy and heat production. \\\\ \\\\ New fluorescents with large Stokes shifts have been produced, capable of working without wavelength shifters. Coherent multibundles have been developed to achieve high packing fractions. Small segments of tracker shell have been assembled and beam tests have confirmed expectations on spatial resolution. An opto-electronic delay line has been designed to delay the track patterns and enable coincidences with a first level trigger. Replacement of the conventional phosphor screen anode with a Si pixel chip is achieved. This tube is called ISPA-tube and has already been operated in beam tests with a scintillating fibres tracker. \\\\ \\\\ The aim of the proposal is to improve hit densities for small diameter fibres by increasing the fraction of trapped light, by reducing absorption and reflection losses, by reflecting light at the free fibre end, and by inc...

  6. Step index fibre using laser interferometer

    Indian Academy of Sciences (India)

    A M Hamed

    2014-03-01

    model is suggested to describe the fringe shift which occurs due to the phase variations of cladded glass fibre introduced between the two plates of the liquid wedge interferometer illuminated with a He–Ne laser. The fringe shift of the phase object which appears in the denominator of the Airy distribution formula of the multiple beam interference is represented in the harmonic term. An experiment is conducted using liquid wedge interferometer where the step index glass fibre of a nearly quadratic thickness variation is introduced between the two plates of the interferometer. The obtained fringe shift shows a good agreement with the proposed quadratic model. The Matlab code is written to plot the interferometer fringes comprising the shift of the step index fibre. Secondly, recognition of elliptical fibres is outlined using tomographic imaging. Finally, results and concluding remarks are given.

  7. Polarisation control of DFB fibre lasers

    DEFF Research Database (Denmark)

    Varming, Poul; Philipsen, Jacob Lundgreen; Berendt, Martin Ole

    1998-01-01

    The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser......The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser...

  8. Dynamic response analysis of DFB fibre lasers

    DEFF Research Database (Denmark)

    Yujun, Qian; Varming, Poul; Povlsen, Jørn Hedegaard

    1998-01-01

    We present a model for relative intensity noise (RIN) in DFB fibre lasers which predicts measured characteristics accurately. Calculation results implies that the RIN decreases rapidly with stronger Bragg grating and higher pump power. We propose here a simplified model based on three spatially...... independent rate equations to describe the dynamic response of erbium doped DFB fibre lasers on pump power fluctuations, using coupled-mode theory to calculate the steady-state hole-burning of the erbium ion inversion...

  9. Design of distributed feedback fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Søndergaard, Thomas; Varming, Poul

    1997-01-01

    A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift.......A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift....

  10. Energy transfer during the hydroentanglement of fibres

    CSIR Research Space (South Africa)

    Moyo, D

    2012-10-01

    Full Text Available , and the resultant degree of fibre entanglement, determines the tensile strength of the nonwoven fabric as a consequence of the inter-fibre friction. Here, the relationship between hydroentangling energy from the waterjets and the changes it brings about... in the nonwoven fabric strength were studied. In the study, the energies of the waterjets transferred to every fabric sample as a function of the waterjet pressure, machine speed, machine efficiency and the web area weight were quantified, and the resultant...

  11. Fibre-optic sensors in health care

    Science.gov (United States)

    Grazia Mignani, Anna; Baldini, Francesco

    1997-05-01

    Biomedical fibre-optic sensors are attractive for the measurement of physical, chemical and biochemical parameters and for spectral measurements directly performed on the patient. An overview of fibre-optic sensors for in vivo monitoring is given, with particular attention paid to the advantages that these sensors are able to offer in different application fields such as cardiovascular and intensive care, angiology, gastroenterology, ophthalmology, oncology, neurology, dermatology and dentistry.

  12. Angiogenic effect induced by mineral fibres.

    Science.gov (United States)

    Carbonari, Damiano; Campopiano, Antonella; Ramires, Deborah; Strafella, Elisabetta; Staffolani, Sara; Tomasetti, Marco; Curini, Roberta; Valentino, Matteo; Santarelli, Lory; Amati, Monica

    2011-10-09

    Due to the toxic effect of asbestos, other materials with similar chemical-physical characteristics have been introduced to substitute it. We evaluate the angiogenic effect of certain asbestos substitute fibres such as glass fibres (GFs), ceramic fibres (CFs) and wollastonite fibres (WFs) and then compare angiogenic responses to those induced by crocidolite asbestos fibres (AFs). An in vitro model using human endothelial cells in small islands within a culture matrix of fibroblasts (Angio-Kit) was used to evaluate vessel formation. The release of IL-6, sIL-R6, IL-8, VEGF-A and their soluble receptors, sVEGFR-1, sVEGFR-2, was determined in the conditioning medium of Angio-Kit system after fibre treatment. ROS formation and cell viability were evaluated in cultured endothelial cells (HUVEC). To evaluate the involvement of intracellular mechanisms, EGFR signalling, ROS formation and nuclear factor-κB (NFκB) pathway were then inhibited by incubating HUVEC cells with AG1478, NAC and PDTC respectively, and the cytokine and growth factor release was analyzed in the culture medium after 7 days of fibre incubation. Among the mineral fibres tested, WFs markedly induced blood vessel formation which was associated with release of IL-6 and IL-8, VEGF-A and their soluble receptors. ROS production was observed in HUVEC after WFs treatment which was associated with cell cytotoxicity. The EGFR-induced ERK phosphorylation and ROS-mediated NFκB activation were involved in the cytokine and angiogenic factor release. However, only the EGFR activation was able to induce angiogenesis. The WFs are potential angiogenic agents that can induce regenerative cytokine and angiogenic factor production resulting in the formation of new blood vessels.

  13. Photonic crystal fibres in the market

    DEFF Research Database (Denmark)

    Broeng, Jes; Laurila, Marko; Noordegraaf, Danny;

    2011-01-01

    Photonic crystal fibres (PCFs) emerged as a research topic in the mid 1990'ies [1]. Today, 15 years later, these fibres are increasing deployed in various commercial markets. Here, we will address three of these markets; medical imaging, materials processing and sensors. We will describe how...... the PCFs provide radical improvements and illustrate the strong diversity in the evolution of PCFs to serve these different markets....

  14. Force focusing in confined fibres and sheets

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Victor; Cerda, Enrique [Departamento de Fisica, Universidad de Santiago, Av. Ecuador 3493, Santiago (Chile); Witten, T A; Liang Tao [James Franck Institute, University of Chicago, Chicago IL 60637 (United States)], E-mail: t-witten@uchicago.edu

    2008-07-07

    A thin fibre or sheet curled into a circular container has a detached region whose shape and force ratios are independent of material properties and container radius. We compute this shape and compare it with experiments. The discrete forces acting at either end of the detached region have a ratio that depends only on the length of the fibre or sheet relative to the circle radius. We calculate this force ratio in three regimes of circle radius. (fast track communication)

  15. Economics Of Optical Fibre Transmission Systems

    Science.gov (United States)

    Murray, W. J.

    1983-08-01

    Optical fibre as a telecommunication transmission medium has become one of the most significant developments so far of the digital era. A major contributory factor to the availability of optical fibre transmission systems has been the outstanding progress in the technology of manufacturing high quality glass fibre having relatively low attenuation and broad bandwidths. This and other achievements has enabled manufacturers in the United Kingdom to develop a range of optical fibre cables and transmission equipment for operation over short and long distances at the CCITT recommended digital hierarchical rates of 2, 8, 34 and 140Mbit/s which have been adopted by British Telecom (BT) for modernisation to an all digital transmission network. These optical fibre systems are now becoming increasingly price and performance competitive with conventional technology in many parts of telecommunications networks. In the British Telecom (BT) network the 140Mbit/s optical fibre systems are now economically competitive with equivalent systems on coaxial cable and microwave radio. The economics of 8 and 34Mbit/s systems are not yet sufficiently attractive, compared with 2Mbit/s digital line systems on pair type copper cables, for large scale use in rural and local distribution networks and are presently only justified on cost in and around large cities. As system costs decrease large applications are predicted particularly in support of future high speed data, cable television and visual information services.

  16. Fibre positioning algorithms for the WEAVE spectrograph

    Science.gov (United States)

    Terrett, David L.; Lewis, Ian J.; Dalton, Gavin; Abrams, Don Carlos; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Middleton, Kevin; Trager, Scott C.

    2014-07-01

    WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. It is a multi-object "pick and place" fibre fed spectrograph with more than one thousand fibres, similar in concept to the Australian Astronomical Observatory's 2dF1 instrument with two observing plates, one of which is observing the sky while other is being reconfigured by a robotic fibre positioner. It will be capable of acquiring more than 10000 star or galaxy spectra a night. The WEAVE positioner concept uses two robots working in tandem in order to reconfigure a fully populated field within the expected 1 hour dwell-time for the instrument (a good match between the required exposure times and the limit of validity for a given configuration due to the effects of differential refraction). This presents additional constraints and complications for the software that determines the optimal path from one configuration to the next, particularly given the large number of fibre crossings implied by the 1000 fibre multiplex. This paper describes the algorithms and programming techniques used in the prototype implementations of the field configuration tool and the fibre positioner robot controller developed to support the detailed design of WEAVE.

  17. Criticality and isostaticity in fibre networks

    Science.gov (United States)

    Broedersz, Chase P.; Mao, Xiaoming; Lubensky, Tom C.; Mackintosh, Frederick C.

    2011-12-01

    Disordered fibre networks are the basis of many man-made and natural materials, including structural components of living cells and tissue. The mechanical stability of such networks relies on the bending resistance of the fibres, in contrast to rubbers, which are governed by entropic stretching of polymer segments. Although it is known that fibre networks exhibit collective bending deformations, a fundamental understanding of such deformations and their effects on network mechanics has remained elusive. Here we introduce a lattice-based model of fibrous networks with variable connectivity to elucidate the roles of single-fibre elasticity and network structure. These networks exhibit both a low-connectivity rigidity threshold governed by fibre-bending elasticity and a high-connectivity threshold governed by fibre-stretching elasticity. Whereas the former determines the true onset of network rigidity, we show that the latter exhibits rich zero-temperature critical behaviour, including a crossover between various mechanical regimes along with diverging strain fluctuations and a concomitant diverging correlation length.

  18. Oblique dust density waves

    Science.gov (United States)

    Piel, Alexander; Arp, Oliver; Menzel, Kristoffer; Klindworth, Markus

    2007-11-01

    We report on experimental observations of dust density waves in a complex (dusty) plasma under microgravity. The plasma is produced in a radio-frequency parallel-plate discharge (argon, p=15Pa, U=65Vpp). Different sizes of dust particles were used (3.4 μm and 6.4μm diameter). The low-frequency (f 11Hz) dust density waves are naturally unstable modes, which are driven by the ion flow in the plasma. Surprisingly, the wave propagation direction is aligned with the ion flow direction in the bulk plasma but becomes oblique at the boundary of the dust cloud with an inclination of 60^o with respect to the plasma boundary. The experimental results are compared with a kinetic model in the electrostatic approximation [1] and a fluid model [2]. Moreover, the role of dust surface waves is discussed. [1] M. Rosenberg, J. Vac. Sci. Technol. A 14, 631 (1996) [2] A. Piel et al, Phys. Rev. Lett. 97, 205009 (2006)

  19. Planar dust-acoustic waves in electron-positron-ion-dust plasmas with dust size distribution

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hong-Yan; Zhang, Kai-Biao [Sichuan University of Science and Engineering, Zigong (China)

    2014-06-15

    Nonlinear dust-acoustic solitary waves which are described with a Kortweg-de vries (KdV) equation by using the reductive perturbation method, are investigated in a planar unmagnetized dusty plasma consisting of electrons, positrons, ions and negatively-charged dust particles of different sizes and masses. The effects of the power-law distribution of dust and other plasma parameters on the dust-acoustic solitary waves are studied. Numerical results show that the dust size distribution has a significant influence on the propagation properties of dust-acoustic solitons. The amplitudes of solitary waves in the case of a power-law distribution is observed to be smaller, but the soliton velocity and width are observed to be larger, than those of mono-sized dust grains with an average dust size. Our results indicate that only compressed solitary waves exist in dusty plasma with different dust species. The relevance of the present investigation to interstellar clouds is discussed.

  20. Dust exposure in Finnish foundries.

    Science.gov (United States)

    Siltanen, E; Koponen, M; Kokko, A; Engström, B; Reponen, J

    1976-01-01

    Dust measurements were made in 51 iron, 9 steel, and 8 nonferrous foundries, at which 4,316 foundrymen were working. The sampling lasted at least two entire shifts or work days continuously during various operations in each foundry. The dust samples were collected at fixed sites or in the breathing zones of the workers. The mass concentration was determined by weighing and the respirable dust fraction was separated by liquid sedimentation. The free silica content was determined by X-ray diffraction. In the study a total of 3,188 samples were collected in the foundries and 6,505 determinations were made in the laboratory. The results indicated a definite difference in the dust exposure during various operations. The highest dust exposures were found during furnace, cupola, and pouring ladle repair. During cleaning work, sand mixing, and shake-out operations excessive silica dust concentrations were also measured. The lowest dust concentrations were measured during melting and pouring operations. Moderate dust concentrations were measured during coremaking and molding operations. The results obtained during the same operations of iron and steel foundries were similar. The distribution of the workers into various exposure categories, the content of respirable dust and quartz, the correlation between respirable dust and total dust, and the correlation between respirable silica and total dust concentrations are discussed. Observations concerning dust suppression and control methods are briefly considered.

  1. Analytical Study of Nonlinear Dust Acoustic Waves in Two-Dimensional Dust Plasma with Dust Charge Variation

    Institute of Scientific and Technical Information of China (English)

    LIN Chang; ZHANG Xiu-Lian

    2005-01-01

    The nonlinear dust acoustic waves in two-dimensional dust plasma with dust charge variation is analytically investigated by using the formally variable separation approach. New analytical solutions for the governing equation of this system have been obtained for dust acoustic waves in a dust plasma for the first time. We derive exact analytical expressions for the general case of the nonlinear dust acoustic waves in two-dimensional dust plasma with dust charge variation.

  2. Jute fibre reinforced plastic: evaluation of application based properties

    Directory of Open Access Journals (Sweden)

    J. B. Sajin

    2015-01-01

    Full Text Available A fibre extracted from jute is a budding component identified for its potential application in composites. It is imperative to evaluate the parametric and property based features to determine its suitability. In this research study, considering the possible application of the fibre composites, the aptness of these fibres are examined with respect to their physical, mechanical [by layered manufacturing technique(LM] and thermal properties. This study focuses on evaluating the properties and behaviour of raw Jute fibres and NaOH surface treated fibres. Subsequently, the fibres are subjected to thermo-gravimetry tests. The outcome of the thermal analysis clearly indicates that the temperature peak shifts to a higher region in the treated fibre compared to raw fibre. The overall observation strongly emphasize that the physical properties and the thermal behaviour of jute fibre are enhanced after surface treatments which makes it more feasible for its application in composite structures.

  3. Loss of type I fibres in canine pectineus muscle hypotrophy.

    Science.gov (United States)

    Ihemelandu, E C

    1980-01-01

    The total number of fibres, as well as, the number of fibres per fibre type were determined by the indirect fibre-counting method in 32 pectineus muscles from 16 dogs of mixed sexes. Eight pairs of muscles from 8 dogs were judged to be hypotrophic, while the other 8 pairs from another 8 dogs were judged to be normal. The hypotrophic muscles had extremely small muscle fibres, particularly type II fibres. They also had apparently higher percentages of type II muscle fibres within a section. The apparently higher percentage of type II fibres usually observed in the hitsochemical examination of the sections of hypotrophic pectineus muscles did not result from failure of type II fibres to transform to type I fibres. It was rather due to too few type I fibres being present in these muscles as compared to the normal muscles. It was not because there were more type II fibres present in them than in the normal muscles. The fewer type I fibres resulted most likely from loss of already differentiated type I fibres. The loss may be of neural origin.

  4. The effect of fibre content, fibre size and alkali treatment to Charpy impact resistance of Oil Palm fibre reinforced composite material

    Science.gov (United States)

    Fitri, Muhamad; Mahzan, Shahruddin

    2016-11-01

    In this research, the effect of fibre content, fibre size and alkali treatment to the impact resistance of the composite material have been investigated, The composite material employs oil palm fibre as the reinforcement material whereas the matrix used for the composite materials are polypropylene. The Oil Palm fibres are prepared for two conditions: alkali treated fibres and untreated fibres. The fibre sizes are varied in three sizes: 5mm, 7mm and 10mm. During the composite material preparation, the fibre contents also have been varied into 3 different percentages: 5%, 7% and 10%. The statistical approach is used to optimise the variation of specimen determined by using Taguchi method. The results were analyzed also by the Taguchi method and shows that the Oil Palm fibre content is significantly affect the impact resistance of the polymer matrix composite. However, the fibre size is moderately affecting the impact resistance, whereas the fibre treatment is insignificant to the impact resistance of the oil palm fibre reinforced polymer matrix composite.

  5. The development of a HEPA filter with improved dust holding characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Dyment, J.; Hamblin, C.

    1995-02-01

    A limitation of the HEPA filters used in the extract of nuclear facilities is their relatively low capacity for captured dust. The costs associated with the disposal of a typical filter means that there are clear incentives to extend filter life. The work described in this report are the initial stages in the development of a filter which incorporates a medium which enhances its dust holding capacity. Experimental equipment was installed to enable the dust loading characteristics of candidate media to be compared with those of the glass fibre based papers currently used in filter construction. These tests involved challenging representative samples of the media with an air stream containing a controlled concentration of thermally generated sodium chloride particles. The dust loading characteristics of the media were then compared in terms of the rate of increasing in pressure differential. A number of {open_quotes}graded density{close_quotes} papers were subsequently identified which appeared to offer significant improvements in dust holding. In the second phase of the programme deep-pleat filters (1,700 M{sup 3}h{sup {minus}1}) incorporating graded density papers were manufactured and tested. Improvements of up to 50% were observed in their capacity for the sub-micron sodium chloride test dust. Smaller differences (15%) were measured when a coarser, carbon black, challenge was used. This is attributed to the differences in the particles sizes of the two dusts.

  6. Crack Growth Monitoring by Embedded Optical Fibre Bragg Grating Sensors: Fibre Reinforced Plastic Crack Growing Detection

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira; Mikkelsen, Lars Pilgaard; McGugan, Malcolm

    2015-01-01

    This article presents a novel method to asses a crack growing/damage event in fibre reinforced plastic, or adhesive using Fibre Bragg Grating (FBG) sensors embedded in a host material. Different features of the crack mechanism that induce a change in the FBG response were identified. Double Canti...

  7. Magnesium Coated Bioresorbable Phosphate Glass Fibres: Investigation of the Interface between Fibre and Polyester Matrices

    Directory of Open Access Journals (Sweden)

    Xiaoling Liu

    2013-01-01

    Full Text Available Bioresorbable phosphate glass fibre reinforced polyester composites have been investigated as replacement for some traditional metallic orthopaedic implants, such as bone fracture fixation plates. However, composites tested revealed loss of the interfacial integrity after immersion within aqueous media which resulted in rapid loss of mechanical properties. Physical modification of fibres to change fibre surface morphology has been shown to be an effective method to improve fibre and matrix adhesion in composites. In this study, biodegradable magnesium which would gradually degrade to Mg2+ in the human body was deposited via magnetron sputtering onto bioresorbable phosphate glass fibres to obtain roughened fibre surfaces. Fibre surface morphology after coating was observed using scanning electron microscope (SEM. The roughness profile and crystalline texture of the coatings were determined via atomic force microscope (AFM and X-ray diffraction (XRD analysis, respectively. The roughness of the coatings was seen to increase from 40±1 nm to 80±1 nm. The mechanical properties (tensile strength and modulus of fibre with coatings decreased with increased magnesium coating thickness.

  8. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin;

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature ph...

  9. Estimation of Single-fibre Tensile Properties from the Bundle Tensile Curve of Polyester Fibres

    Institute of Scientific and Technical Information of China (English)

    于伟东

    2004-01-01

    Fibre bundle tensile curves can be used to characterise fibre processing properties and end-use performance directly and to predict single-fibre properties in theory. In this paper, the tensile behaviour of polyester fibre-bundles has been analysed in characteristic values and diagramming. The characteristic distributions which include the symmetry distribution on right part, SRBS′ (e), on left part, SLBS′(e) and the curve on base-line modification, MBS′ (e),based on the modulus distribution, BS′ (e), as well as the frequency density function of broken fibres, B′ (e), have been derived from the tail of bundle tensile curves. The theoretical and measured results show that the most important curves are MBS′ ( e ) and B′ ( e ) and can be used to estimate the breaking-extension distribution of single fibres. Especially for MBS′(e), the modulus distribution can accurately characterize single-fibre tensile properties and is no limitation as the calculation of B′(e) because the bundle specific stress Y(e) of no fibre breaking at extension e should be found at first.

  10. Dust Devil Days

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] Released 6 July 2004 The atmosphere of Mars is a dynamic system. Water-ice clouds, fog, and hazes can make imaging the surface from space difficult. Dust storms can grow from local disturbances to global sizes, through which imaging is impossible. Seasonal temperature changes are the usual drivers in cloud and dust storm development and growth. Eons of atmospheric dust storm activity has left its mark on the surface of Mars. Dust carried aloft by the wind has settled out on every available surface; sand dunes have been created and moved by centuries of wind; and the effect of continual sand-blasting has modified many regions of Mars, creating yardangs and other unusual surface forms. Dust devils, small cyclonic wind storms, are common in the American Southwest and on Mars. As the dust devil moves across the surface it picks up the loose dust, leaving behind a dark track to mark its passage. These dust devil tracks are in the Argyre Basin. Image information: VIS instrument. Latitude -46.6, Longitude 317.5 East (42.5 West). 19 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the

  11. Dust Devil Tracks

    Science.gov (United States)

    Reiss, Dennis; Fenton, Lori; Neakrase, Lynn; Zimmerman, Michael; Statella, Thiago; Whelley, Patrick; Rossi, Angelo Pio; Balme, Matthew

    2016-11-01

    Dust devils that leave dark- or light-toned tracks are common on Mars and they can also be found on the Earth's surface. Dust devil tracks (hereinafter DDTs) are ephemeral surface features with mostly sub-annual lifetimes. Regarding their size, DDT widths can range between ˜1 m and ˜1 km, depending on the diameter of dust devil that created the track, and DDT lengths range from a few tens of meters to several kilometers, limited by the duration and horizontal ground speed of dust devils. DDTs can be classified into three main types based on their morphology and albedo in contrast to their surroundings; all are found on both planets: (a) dark continuous DDTs, (b) dark cycloidal DDTs, and (c) bright DDTs. Dark continuous DDTs are the most common type on Mars. They are characterized by their relatively homogenous and continuous low albedo surface tracks. Based on terrestrial and martian in situ studies, these DDTs most likely form when surficial dust layers are removed to expose larger-grained substrate material (coarse sands of ≥500 μm in diameter). The exposure of larger-grained materials changes the photometric properties of the surface; hence leading to lower albedo tracks because grain size is photometrically inversely proportional to the surface reflectance. However, although not observed so far, compositional differences (i.e., color differences) might also lead to albedo contrasts when dust is removed to expose substrate materials with mineralogical differences. For dark continuous DDTs, albedo drop measurements are around 2.5 % in the wavelength range of 550-850 nm on Mars and around 0.5 % in the wavelength range from 300-1100 nm on Earth. The removal of an equivalent layer thickness around 1 μm is sufficient for the formation of visible dark continuous DDTs on Mars and Earth. The next type of DDTs, dark cycloidal DDTs, are characterized by their low albedo pattern of overlapping scallops. Terrestrial in situ studies imply that they are formed when sand

  12. Dust during the Reionization

    CERN Document Server

    Elfgren, E; Elfgren, Erik

    2003-01-01

    The possibility that population III stars have reionized the Universe at redshifts greater than 6 has recently gained momentum with WMAP polarization results. Here we analyse the role of early dust produced by these stars and ejected into the intergalactic medium. We show that this dust, heated by the radiation from the same population III stars, produces a submillimetre excess. The electromagnetic spectrum of this excess is compatible with the FIRAS (Far Infrared Absolute Spectrophotometer) cosmic far infrared background. This spectrum, a Doppler spectrum times the $\

  13. Strength Evaluation of Steel-Nylon Hybrid Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    Maniram Kumar

    2014-07-01

    Full Text Available When fibres like steel, glass, polypropylene, nylon, carbon, aramid, polyester, jute, etc are mixed with concrete known as fibre reinforced concrete. To overcome the deficiencies of concrete; fibres are added to improve the performance of concrete. In this research hybrid reinforced concrete is made by using steel and nylon 6 fibres. The inclusion of both steel and nylon 6 fibres are used in order to combine the benefits of both fibers; structural improvements provided by steel fibers and the resistance to plastic shrinkage improvements provided by nylon fibers. So the aim of this project is to investigate the mechanical properties (compressive strength, flexure strength and split tensile strength of hybrid fiber reinforced concrete under compression, flexure & tension. The total volume of fibre was taken 0.75 % of total volume of concrete. In this experimental work, four different concrete mix proportions were casted with fibres and one mix without fibres. Four different mix combinations of steel- nylon 6 fibres were 100-00%, 75-25%, 50-50% and 25-75%. Superplasticizer was used in all mixes to make concrete more workable. The results shown that compressive, split tensile and flexural strength of hybrid fibre reinforced concrete increase by increasing quantity of steel and nylon 6 fibres. The increase in compressive and tensile strength due to incorporation of steel fibre is greater than that of using nylon fibre. For the nylon 6 fibres, adding more fibres into the concrete has a limited improvement on splitting tensile strength. Inclusion of nylon 6 fibres along with steel fibres results in considerable improvement in flexural strength as compared to solo steel fibre.

  14. Electrostatic Characterization of Lunar Dust

    Science.gov (United States)

    2008-01-01

    To ensure the safety and success of future lunar exploration missions, it is important to measure the toxicity of the lunar dust and its electrostatic properties. The electrostatic properties of lunar dust govern its behavior, from how the dust is deposited in an astronaut s lungs to how it contaminates equipment surfaces. NASA has identified the threat caused by lunar dust as one of the top two problems that need to be solved before returning to the Moon. To understand the electrostatic nature of lunar dust, NASA must answer the following questions: (1) how much charge can accumulate on the dust? (2) how long will the charge remain? and (3) can the dust be removed? These questions can be answered by measuring the electrostatic properties of the dust: its volume resistivity, charge decay, charge-to-mass ratio or chargeability, and dielectric properties.

  15. D fibre antenna for microcellular communications

    Energy Technology Data Exchange (ETDEWEB)

    Bhatti, Ajaz

    2003-07-01

    Over the years, optical fibre sensors have been developed for many application areas. With the recent growth of microcellular communication systems this area has great economic potential. Therefore with this in mind one promising application for a new optical fibre sensor system is in the detection of Radio Frequency/Electric Fields (RF/EF). By constructing such a sensor from totally dielectric materials, it could be used as an antenna for receiving radio frequency transmissions without distorting or disturbing the field lines since there are no metallic components to reflect or transmit radio frequency energy. One of the key issues in the realisation of Radio-over-Fibre (RoF) architecture is the development of an effective means of generating and transmitting the radio subcarrier. The simplest method for the optical generation of radio signals, for transmission through an optical network is to directly modulate the light source with the received RF signal. Direct modulation of the laser can lead to a number of problems such as relative intensity noise (RIN), chirp and intermodulation distortion (IMD). A novel approach as described in this thesis, for generating an externally modulated optical signal would be to use an optical antenna comprising of a piezoelectric polymer coated D-fibre configured within a Mach-Zehnder interferometer to phase modulate the lightwave with a received RF electrical signal. One of the primary advantages of the D-fibre antenna over conventional antennae is its ability to serve a dual purpose. First it can be used to directly detect the RF signal, and secondly it provides a convenient means for modulating the light within the fibre thus bypassing the need for directly modulating the laser. The work presented in this thesis forms a comprehensive study on the design and modelling of a novel all-optical antenna using D-shaped optical fibre for use in next generation RoF networks. For the first time Finite Element Analysis (FEA) has been used

  16. Fibre Bragg Grating and Long Period Grating Sensors in Polymer Optical Fibres

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar

    of applications and pushing the limits. The first part of the work focuses on the fabrication of FBGs in polymer optical fibres. FBGs are a periodic perturbation of the refractive index of the optical fibre core which act as a wavelength specific reflector. The fibres used are made of Polymethyl methacrylate......, strain duration, increasing number of cycles, and it decreases with relaxation duration. For strains up to 0.9%, fast relaxing ΔΛfast range takes no less than 65% of the total strain range. Increase in ΔΛslow due to cyclic straining and relaxing seems to reach an equilibrium value, suggesting that ΔΛslow...... which translates the outside pressure into strain on the fibre. The transducer consisted of a 3Dprinted skeleton through which the fibre is pulled. A latex material is then wrapped around it and all the holes were sealed in order to prevent the air from leaking out. The pod transducer was tested...

  17. Study of the behaviour of the fibre Bragg grating fabricated with cladding mode suppression fibre

    Institute of Scientific and Technical Information of China (English)

    徐新华; 吕昌贵; 崔一平

    2003-01-01

    One effective method for suppression of coupling from guided optical modes into cladding modes in an optical fibre Bragg grating is to use cladding mode suppression fibre.In this specially engineered fibre,the grating is written into the core and the inner cladding,both of which are photosensitive.A theory is presented in this paper to analyse the spectral characteristics of this kind of gratings.A fibre Bragg grating was experimentally fabricated with this kind of photosensitive fibre(PS-RMS-50 from StockerYale).It is shown both theoretically and experimentally that such gratings exhibit strong suppression of the coupling between core mode and cladding mode.The experimental result is in good agreement with the theoretical analysis.

  18. Hemp fibres: Enzymatic effect of microbial processing on fibre bundle structure

    DEFF Research Database (Denmark)

    Thygesen, Anders; Liu, Ming; Meyer, Anne S.

    2013-01-01

    The effects of microbial pretreatment on hemp fibres were evaluated after microbial retting using the white rot fungi Ceriporiopsis subvermispora and Phlebia radiata Cel 26 and water retting. Based on chemical composition, P. radiata Cel 26 showed the highest selectivity for pectin and lignin...... degradation and lowest cellulose loss (14%) resulting in the highest cellulose content (78.4%) for the treated hemp fibres. The pectin and lignin removal after treatment with P. radiata Cel 26 were of the order 82% and 50%, respectively. Aligned epoxy-matrix composites were made from hemp fibres defibrated...... hemp fibres were badly impregnated due to porosity caused by surface impurities such as epidermis and other pectin rich plant cells. The pectin and lignin mainly located in the outer part of the fibres were assumed to be extracted and degraded by pectinase and peroxidase enzymes produced by the fungi....

  19. Polarisation maintaining fibre with pure silica core and two depressed claddings for fibre optic gyroscope

    Science.gov (United States)

    Kurbatov, A. M.; Kurbatov, R. A.; Voloshin, V. V.; Vorob'ev, I. L.; Kolosovsky, A. O.

    2016-12-01

    Polarisation maintaining (PM) fibre is described with pure silica core and two depressed claddings for fibre optic gyro (FOG) sensing coil. Detailed mathematical simulation is presented by supermodes method, which is extremely necessary for such fibre. Simulation is fulfilled by frequency domain finite difference method (FDFDM), taking into account all details of realistic index profile with stress applying parts, while the leakage/bend loss occur in the region with complex index, surrounding the fibre. Cutoff and small bend loss are theoretically predicted and experimentally measured with excellent agreement between theory and experiment. Polarisation maintaining ability is measured in the form of conventional h-parameter (7.1·10-6 1/m) for 90-μm diameter fibre with birefringence value only 3.9·10-4.

  20. DESIGN NOTE: Surface microscopy and fibre characterization using a multimode-fibre reflectance microscope

    Science.gov (United States)

    Lukins, P. B.; Rehman, S.; Stevens, G. B.

    2000-04-01

    A remarkably simple scanning infrared surface-reflectance microscope based on a multimode-fibre-coupled diode laser together with straightforward electronics and scanning stage is described. The design does not require alignment and completely avoids the use of objectives, beamsplitters and other optics normally associated with such microscopes. The axial response, resolution and imaging properties for non-interferometric operation are characterized. A geometric model for the transmission of such a microscope using an idealized step/graded-index multimode fibre is presented. This model is used to explain the axial response of the microscope. Finally, a new method for determination of the numerical aperture and index-grading parameter of multimode fibres is proposed. This method is based on the geometric model together with axial-response measurements using the microscope in such a way that the fibre probe is the actual test fibre.

  1. Mechanical processing of bast fibres: The occurrence of damage and its effect on fibre structure

    DEFF Research Database (Denmark)

    Hänninen, Tuomas; Thygesen, Anders; Mehmood, Shahid

    2012-01-01

    Currently, separation processes used for natural fibres for composite reinforcing textiles cause a significant amount of damage to the fibres. Microscopic analysis showed that industrially processed flax (Linum usitassimium L.) fibres contained significantly more defects than green or retted ones...... and that further mechanical processing did not significantly increase the amount of defects. In this study it has been shown, by analysing the degree of polymerisation of cell wall components indirectly by viscosity measurements, that mechanically induced defects do not significantly cleave the cell wall polymers....... Acid hydrolysis, however, induced more degradation of the cell wall polymers in fibres having a greater degree of damage, indicating that that defects are more susceptible to certain chemical reactions and which in turn might cause problems for example, during chemical modification of fibres due...

  2. Effects of Polarization-Maintaining Fibre Degrading on Precision of Fibre Optic Gyroscopes in Radiation Environment

    Institute of Scientific and Technical Information of China (English)

    XIAO Wen; LIU De-Wen; LIU Yang; YI Xiao-Su; CONG Lin

    2008-01-01

    @@ In the space environment, the precision of fibre optic gyroscopes (FOGs) degrades because of space radiation.Photonic components of FOGs axe affected by radiation, especially the polaxization-maintaining (PM) fibre coil.In relation to the space radiation environment characteristic, we have carried out a series of radiation experiments on a PM fibre coil with 60Co radiation source at different dose rates. Based on the experimental results, the formula between the PM-fibre loss and radiation dose rata is built, and the relation between the precision of FOG and radiation dose is obtained accordingly. The results strongly show that the precision of our FOG degrades owing to the attenuation of the polarization-maintaining fibre, which provides theoretical foundation for the radiation-resistant design of the FOG.

  3. Voronoi cells, fractal dimensions and fibre composites.

    Science.gov (United States)

    Summerscales, J.; Guild, F. J.; Pearce, N. R. L.; Russell, P. M.

    2001-02-01

    The use of fibre-reinforced polymer matrix composite materials is growing at a faster rate than the gross domestic product (GDP) in many countries. An improved understanding of their processing and mechanical behaviour would extend the potential applications of these materials. For unidirectional composites, it is predicted that localized absence of fibres is related to longitudinal compression failure. The use of woven reinforcements permits more effective manufacture than for unidirectional fibres. It has been demonstrated experimentally that compression strengths of woven composites are reduced when fibres are clustered. Summerscales predicted that clustering of fibres would increase the permeability of the reinforcement and hence expedite the processing of these materials. Commercial fabrics are available which employ this concept using flow-enhancing bound tows. The net effect of clustering fibres is to enhance processability whilst reducing the mechanical properties. The effects reported above were qualitative correlations. To improve the design tools for reinforcement fabrics we have sought to quantify the changes in the micro/meso-structure of woven reinforcement fabrics. Gross differences in the appearance of laminate sections are apparent for different weave styles. The use of automated image analysis is essential for the quantification of subtle changes in fabric architecture. This paper considers Voronoi tessellation and fractal dimensions for the quantification of the microstructures of woven fibre-reinforced composites. It reviews our studies in the last decade of the process-property-structure relationships for commercial and experimental fabric reinforcements in an attempt to resolve the processing vs. properties dilemma. A new flow-enhancement concept has been developed which has a reduced impact on laminate mechanical properties.

  4. Latest developments in silica fibre luminescence dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, D. A.; Abdul S, S. F.; Jafari, S. M.; Alanazi, A. [University of Surrey, Department of Physics, GU2 7XH Guildford, Surrey (United Kingdom); Amouzad M, G. [University of Malaya, Faculty of Engineering, Department of Electrical Engineering, Integrated Lightwave Research Group, 50603 Kuala Lumpur (Malaysia); Addul R, H. A.; Mizanur R, A. K. M.; Zubair, H. T.; Begum, M.; Yusoff, Z.; Omar, N. Y. M. [Multimedia University, Faculty of Engineering, 2010 Cyberjaya, Selangor (Malaysia); Maah, M. J. [University of Malaya, Department of Chemistry, 50603 Kuala Lumpur (Malaysia); Collin, S. [National Physical Laboratory, Hampton Road, Teddington, TW11 OLW Middlesex (United Kingdom); Mat-Sharif, K. A.; Muhd-Yassin, S. Z.; Zulkifli, M. I., E-mail: d.a.bradley@surrey.ac.uk [Telekom Malaysia Research and Development Sdn Bhd., 63000 Cyberjaya, Selangor (Malaysia)

    2015-10-15

    Full text: Using tailor made sub-mm diameter doped-silica fibres, we are carrying out luminescence dosimetry studies for a range of situations, including thermoluminescence (Tl)investigations on a liquid alpha source formed of {sup 223}RaCl (the basis of the Bayer Health care product Xofigo), the Tl response to a 62 MeV proton source and Tl response to irradiation from an {sup 241}Am-Be neutron source. In regard to the former, in accord with the intrinsic high linear energy transfer (Let) and short path length (<100 um) of the α-particles in calcified tissue, the product is in part intended as a bone-seeking radionuclide for treatment of metastatic cancer, offering high specificity and efficacy. The Tl yield of Ge-doped SiO{sub 2} fibres has been investigated including for photonic crystal fibre un collapsed, flat fibres and single mode fibres, these systems offering many advantages over conventional passive dosimetry types. In particular, one can mention comparable and even superior sensitivity, an effective atomic number Z{sub eff} of the silica dosimetric material close to that of bone, and the glassy nature of the fibres offering the additional advantage of being able to place such dosimeters directly into liquid environments. Finally we review the use of our tailor made fibres for on-line radioluminescence measurements of radiotherapy beams. The outcome from these various lines of research is expected to inform development of doped fiber radiation dosimeters of versatile utility, ranging from clinical applications through to industrial studies and environmental evaluations. (Author)

  5. Microanalytical investigation of fibre-reinforced ceramic materials

    Energy Technology Data Exchange (ETDEWEB)

    Meier, B.; Grathwohl, G.

    1989-03-01

    Microanalytical investigations have been made on samples of ceramic fibres (SiC fibres, (Nicalon) C fibre coated with TiN) and fibre-reinforced ceramics (SiC-and glass-matrices). High resolution Auger electron spectroscopy (HRAES), electron probe microanalysis (EPMA) and scanning electron microscopy were employed for these examinations. Analysis was best performed with HRAES on account of its lateral and depth resolution. Some of the problems involved in this technique are discussed e.g. electron beam effects. AES depth profiles of ceramic fibres are reported and compared with the surface analysis of fibres in the composites after being broken in situ.

  6. Influence of the Testing Gage Length on the Strength, Young's Modulus and Weibull Modulus of Carbon Fibres and Glass Fibres

    Directory of Open Access Journals (Sweden)

    Luiz Claudio Pardini

    2002-10-01

    Full Text Available Carbon fibres and glass fibres are reinforcements for advanced composites and the fiber strength is the most influential factor on the strength of the composites. They are essentially brittle and fail with very little reduction in cross section. Composites made with these fibres are characterized by a high strength/density ratio and their properties are intrisically related to their microstructure, i.e., amount and orientation of the fibres, surface treatment, among other factors. Processing parameters have an important role in the fibre mechanical behaviour (strength and modulus. Cracks, voids and impurities in the case of glass fibres and fibrillar misalignments in the case of carbon fibres are created during processing. Such inhomogeneities give rise to an appreciable scatter in properties. The most used statistical tool that deals with this characteristic variability in properties is the Weibull distribution. The present work investigates the influence of the testing gage length on the strength, Young's modulus and Weibull modulus of carbon fibres and glass fibres. The Young's modulus is calculated by two methods: (i ASTM D 3379M, and (ii interaction between testing equipment/specimen The first method resulted in a Young modulus of 183 GPa for carbon fibre, and 76 GPa for glass fibre. The second method gave a Young modulus of 250 GPa for carbon fibre and 50 GPa for glass fibre. These differences revelead differences on how the interaction specimen/testing machine can interfere in the Young modulus calculations. Weibull modulus can be a tool to evaluate the fibre's homogeneity in terms of properties and it is a good quality control parameter during processing. In the range of specimen gage length tested the Weibull modulus for carbon fibre is ~ 3.30 and for glass fibres is ~ 5.65, which indicates that for the batch of fibres tested, the glass fibre is more uniform in properties.

  7. Identification of the exploatation dust in road dust

    Directory of Open Access Journals (Sweden)

    B. Gajdzik

    2012-01-01

    Full Text Available The aim of this publication is to determine models of explore dust from vehicle brake systems and the presentationof measurement results of the exploitation dust, which is separate from road dust. The following methods and measuring devices were used: T-01M device, screen analysis, analysis of chemical composition with the use of a scanning microscope with Energy Dispersive x-ray Spectroscopy (EDS analyser. The measurements for identifying this type of dust were conducted on marked sections of roads: motorway, city road and mountain road. The explored dust was distinguished in the following car systems: brakes, clutch plates, tyres and catalytic converters.

  8. Cylindrically symmetric dust spacetime

    CERN Document Server

    Senovilla, J M M; Senovilla, Jose M. M.; Vera, Raul

    2000-01-01

    We present an explicit exact solution of Einstein's equations for an inhomogeneous dust universe with cylindrical symmetry. The spacetime is extremely simple but nonetheless it has new surprising features. The universe is ``closed'' in the sense that the dust expands from a big-bang singularity but recollapses to a big-crunch singularity. In fact, both singularities are connected so that the whole spacetime is ``enclosed'' within a single singularity of general character. The big-bang is not simultaneous for the dust, and in fact the age of the universe as measured by the dust particles depends on the spatial position, an effect due to the inhomogeneity, and their total lifetime has no non-zero lower limit. Part of the big-crunch singularity is naked. The metric depends on a parameter and contains flat spacetime as a non-singular particular case. For appropriate values of the parameter the spacetime is a small perturbation of Minkowski spacetime. This seems to indicate that flat spacetime may be unstable agai...

  9. Cylindrically symmetric dust spacetime

    Science.gov (United States)

    Senovilla, José M. M.

    2000-07-01

    We present an explicit exact solution of Einstein's equations for an inhomogeneous dust universe with cylindrical symmetry. The spacetime is extremely simple but nonetheless it has surprising new features. The universe is `closed' in the sense that the dust expands from a big-bang singularity but recollapses to a big-crunch singularity. In fact, both singularities are connected so that the whole spacetime is `enclosed' within a single singularity of general character. The big-bang is not simultaneous for the dust, and in fact the age of the universe as measured by the dust particles depends on the spatial position, an effect due to the inhomogeneity, and their total lifetime has no non-zero lower limit. Part of the big-crunch singularity is naked. The metric depends on a parameter and contains flat spacetime as a non-singular particular case. For appropriate values of the parameter the spacetime is a small perturbation of Minkowski spacetime. This seems to indicate that flat spacetime may be unstable against some global non-vacuum perturbations.

  10. Left in the Dust

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    NASA's Stardust spacecraft ended its seven-year voyage January 15 after a safe landing on earth, bringing back a capsule of comet particles and samples of interstellar dust that exceeded the loftiest of expectations of mission scientists. The ensuing studies of the cosmic treasure are expected to shed light on the origins of the solar system and earth itself.

  11. Dust devil dynamics

    Science.gov (United States)

    Horton, W.; Miura, H.; Onishchenko, O.; Couedel, L.; Arnas, C.; Escarguel, A.; Benkadda, S.; Fedun, V.

    2016-06-01

    A self-consistent hydrodynamic model for the solar heating-driven onset of a dust devil vortex is derived and analyzed. The toroidal flows and vertical velocity fields are driven by an instability that arises from the inversion of the mass density stratification produced by solar heating of the sandy surface soil. The nonlinear dynamics in the primary temperature gradient-driven vertical airflows drives a secondary toroidal vortex flow through a parametric interaction in the nonlinear structures. While an external tangential shear flow may initiate energy transfer to the toroidal vortex flow, the nonlinear interactions dominate the transfer of vertical-radial flows into a fast toroidal flow. This secondary flow has a vertical vorticity, while the primary thermal gradient-driven flow produces the toroidal vorticity. Simulations for the complex nonlinear structure are carried out with the passive convection of sand as test particles. Triboelectric charging modeling of the dust is used to estimate the charging of the sand particles. Parameters for a Dust Devil laboratory experiment are proposed considering various working gases and dust particle parameters. The nonlinear dynamics of the toroidal flow driven by the temperature gradient is of generic interest for both neutral gases and plasmas.

  12. GLUT4 expression at the plasma membrane is related to fibre volume in human skeletal muscle fibres

    DEFF Research Database (Denmark)

    Gaster, M; Vach, W; Beck-Nielsen, H

    2002-01-01

    In this study we examined the relationship between GLUT4 expression at the plasma membrane and muscle fibre size in fibre-typed human muscle fibres by immunocytochemistry and morphometry in order to gain further insight into the regulation of GLUT4 expression. At the site of the plasma membrane......, GLUT4 was more abundantly expressed in slow as compared to fast fibres at the same fibre diameter (p diabetic and obese was reduced...... compared to control subjects at the same diameter (p diabetic subjects expressed a fibre-volume-dependent GLUT4 expression (p diabetic p = 0.06). Our results show that increasing...

  13. Plant fibre composites - porosity and stiffness

    DEFF Research Database (Denmark)

    Madsen, Bo; Thygesen, Anders; Lilholt, Hans

    2009-01-01

    Plant fibre composites contain typically a relatively large amount of porosity which influences their performance. A model, based on a modified rule of mixtures, is presented to include the influence of porosity on the composite stiffness. The model integrates the volumetric composition of the co......Plant fibre composites contain typically a relatively large amount of porosity which influences their performance. A model, based on a modified rule of mixtures, is presented to include the influence of porosity on the composite stiffness. The model integrates the volumetric composition...... of the composites with their mechanical properties. The fibre weight fraction is used as an independent parameter to calculate the complete volumetric composition. A maximum obtainable stiffness of the composites is calculated at a certain transition fibre weight fraction, which is characterised by a best possible...... combination of high fibre volume fraction and low porosity. The model is validated with experimental data from the literature on several types of composites. A stiffness diagram is presented to demonstrate that the calculations can be used for tailoring and design of composites with a given profile...

  14. A large Scintillating Fibre Tracker for LHCb

    Science.gov (United States)

    Greim, R.

    2017-02-01

    The LHCb experiment will be upgraded during LHC Long Shutdown 2 to be able to record data at a higher instantaneous luminosity. The readout rate is currently limited to 1 MHz by the Level 1 trigger. In order to achieve the target integrated luminosity of 50 fb-1 during LHC Run 3, all subdetectors have to be read out by a 40 MHz trigger-less readout system. Especially, the current tracking detectors downstream of the LHCb dipole magnet suffer from large detector dead times and a small granularity in the Outer Tracker, which consists of proportional straw tubes. Therefore, the Downstream Tracker will be replaced by a Scintillating Fibre Tracker with Silicon Photomultiplier readout. The total sensitive area of 340 m2 is made up of 2.5 m long fibre mats consisting of six staggered layers of 250 μm thin scintillating fibres. The scintillation light created by the charged particles traversing the fibre mats is transported to the fibre ends via total internal reflection and detected by state-of-the-art multi-channel SiPM arrays. This paper presents the detector concept, design, challenges, custom-made readout chips, as well as laboratory and beam test results.

  15. Reuyl Crater Dust Avalanches

    Science.gov (United States)

    2002-01-01

    (Released 13 May 2002) The Science The rugged, arcuate rim of the 90 km crater Reuyl dominates this THEMIS image. Reuyl crater is at the southern edge of a region known to be blanketed in thick dust based on its high albedo (brightness) and low thermal inertia values. This thick mantle of dust creates the appearance of snow covered mountains in the image. Like snow accumulation on Earth, Martian dust can become so thick that it eventually slides down the face of steep slopes, creating runaway avalanches of dust. In the center of this image about 1/3 of the way down is evidence of this phenomenon. A few dozen dark streaks can be seen on the bright, sunlit slopes of the crater rim. The narrow streaks extend downslope following the local topography in a manner very similar to snow avalanches on Earth. But unlike their terrestrial counterparts, no accumulation occurs at the bottom. The dust particles are so small that they are easily launched into the thin atmosphere where they remain suspended and ultimately blow away. The apparent darkness of the avalanche scars is due to the presence of relatively dark underlying material that becomes exposed following the passage of the avalanche. Over time, new dust deposition occurs, brightening the scars until they fade into the background. Although dark slope streaks had been observed in Viking mission images, a clear understanding of this dynamic phenomenon wasn't possible until the much higher resolution images from the Mars Global Surveyor MOC camera revealed the details. MOC images also showed that new avalanches have occurred during the time MGS has been in orbit. THEMIS images will allow additional mapping of their distribution and frequency, contributing new insights about Martian dust avalanches. The Story The stiff peaks in this image might remind you of the Alps here on Earth, but they really outline the choppy edge of a large Martian crater over 50 miles wide (seen in the context image at right). While these aren

  16. Mechanical Property Analysis on Sandwich Structured Hybrid Composite Made from Natural Fibre, Glass Fibre and Ceramic Fibre Wool Reinforced with Epoxy Resin

    Science.gov (United States)

    Bharat, K. R.; Abhishek, S.; Palanikumar, K.

    2017-06-01

    Natural fibre composites find wide range of applications and usage in the automobile and manufacturing industries. They find lack in desired properties, which are required for present applications. In current scenario, many developments in composite materials involve the synthesis of Hybrid composite materials to overcome some of the lacking properties. In this present investigation, two sandwich structured hybrid composite materials have been made by reinforcing Aloe Vera-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and Sisal fibre-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and its mechanical properties such as Tensile, Flexural and Impact are tested and analyzed. The test results from the two samples are compared and the results show that sisal fibre reinforced hybrid composite has better mechanical properties than aloe vera reinforced hybrid composite.

  17. Asbestos: scientific basis for environmental control of fibres.

    Science.gov (United States)

    Acheson, E D; Gardner, M J

    1980-01-01

    Any review of the scientific evidence on which public policy is based must commence with a cautionary statement about the quality of the available data both about dust and about asbestos-related disease. Attention is drawn to some of the main problems. It is concluded that, in spite of their shortcomings, the data are sufficiently consistent to be useful in relation to some aspects of the problem of environmental control of the asbestos hazard. The question whether or not there is a threshold dose of fibre below which no biological effect occurs is of considerable importance in framing public policy. The evidence concerning the existence or otherwise of a threshold in relation to the different asbestos-related diseases is summarized. A summary is also given of the evidence about the shape of the dose-response curves for asbestos-related diseases in man. The paper concludes with a note on how scientific data may be summarized in a manner which may be helpful in formulating public policy with regard to a control limit.

  18. EDITORIAL: Optical Fibre Sensors 18 (OFS-18)

    Science.gov (United States)

    Jones, Julian D. C.; Tatam, Ralph P.

    2007-10-01

    The International Conference on Optical Fibre Sensors (OFS-18) was held in October 2006 in Cancún, Mexico, under the general chairmanship of Dr Alexis Mendez (MCH Engineering LLC, USA) and Dr Fernando Mendoza (Centro de Investigaciones en Optica, Mexico). 'OFS', as it has become known, is firmly established as the leading international conference for the optical fibre sensor community. Since its inception, in London in 1983, and under the leadership of an international steering committee independent of any learned society or professional institution, it has been held approximately every eighteen months. The venue nominally rotates from Europe, to the Americas, and thence to Asia and the Pacific. OFS-18 demonstrated the continuing vigour of the community, with some 250 papers presented, plus two workshops, with attendance as international as ever. In recent years, it has become a tradition to publish a post-conference special issue in the journal Measurement Science and Technology, and these special issues offer a representative sample of the current status of the field. In the nearly 25 years since OFS began, many of the early ideas and laboratory-based proof-of-principle experiments have led to highly developed instrumentation systems, and to successful commercial products. Perhaps the most mature of all of these technologies is the optical fibre gyroscope, with the fibre hydrophone a close second—originally developed for defence applications for which it is now established, but with increasing relevance to the oil and gas industry; electromagnetic sensors based on the Faraday and electro-optic effects are of growing significance in the power generation and distribution industry; whilst in-fibre grating-based sensors occupy an expanding niche in structural monitoring, especially in civil engineering. It is therefore appropriate that the first day of OFS was devoted to workshops on structural health monitoring, and to commemorate the 30th anniversary of the

  19. Fatigue processes in thermoplastic fibres; Les mecanismes de fatigue dans les fibres thermoplastiques

    Energy Technology Data Exchange (ETDEWEB)

    Herrera Ramirez, J.M.

    2004-09-15

    The present study examines and compares the behaviour of the two types of PA66 fibres and two types of PET fibres under fatigue loading up to failure, and the correlation between the fibres (nano)structures and their structural heterogeneities, with fatigue lifetimes. Several techniques have been used to analyze the materials, such as scanning electron microscopy (SEM), microanalysis (EDS), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and micro-Raman spectroscopy. A meticulous analysis by scanning electron microscopy of the fracture morphology of fibres broken in tension and in fatigue, as well as a study of the fatigue life, were undertaken. The fatigue process occurs when the cyclic load amplitude is sufficiently large, however a condition for fatigue failure is that the minimum load each cycle must be lower than a threshold stress level. Failure under fatigue conditions leads to distinctive fracture morphologies which are very different from those seen after tensile or creep failure and this allows easy identification of the fatigue process. The fibres have been analyzed in the as received state and after fatigue failure in order to observe the microstructural changes resulting from the fatigue loading. The results will be compared with those obtained for fibres loaded under conditions where the fatigue process was hindered. The role of the microstructure of the fibres in determining fatigue will be discussed in this work and the possibility of improving their resistance to fatigue or eliminating the fatigue process will be discussed. (author)

  20. Study of injection moulded long glass fibre-reinforced polypropylene and the effect on the fibre length and orientation distribution

    Science.gov (United States)

    Parveeen, B.; Caton-Rose, P.; Costa, F.; Jin, X.; Hine, P.

    2014-05-01

    Long glass fibre (LGF) composites are extensively used in manufacturing to produce components with enhanced mechanical properties. Long fibres with length 12 to 25mm are added to a thermoplastic matrix. However severe fibre breakage can occur in the injection moulding process resulting in shorter fibre length distribution (FLD). The majority of this breakage occurs due to the melt experiencing extreme shear stress during the preparation and injection stage. Care should be taken to ensure that the longer fibres make it through the injection moulding process without their length being significantly degraded. This study is based on commercial 12 mm long glass-fibre reinforced polypropylene (PP) and short glass fibre Nylon. Due to the semi-flexiable behaviour of long glass fibres, the fibre orientation distribution (FOD) will differ from the orientation distribution of short glass fibre in an injection molded part. In order to investigate the effect the change in fibre length has on the fibre orientation distribution or vice versa, FOD data was measured using the 2D section image analyser. The overall purpose of the research is to show how the orientation distribution chnages in an injection moulded centre gated disc and end gated plaque geometry and to compare this data against fibre orientation predictions obtained from Autodesk Moldflow Simulation Insight.

  1. Pulse Compression And Raman Amplification In Optical Fibres

    Science.gov (United States)

    Byron, Kevin C.

    1988-06-01

    Experimental and theoretical investigations on Raman amplification in fibres have been carried out and simultaneous amplification and pulse compression observed. With a fibre design optimised for amplification high gain may be obtained at practical pump power levels.

  2. Mechanical Properties of Man-Made Mineral glass fibres

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    In nature basaltic volcanic glass fibres are know from Hawaii as Pele's hair, formed by droplets of lava thrown into the air during volcanic eruption. The concept of glass fibre formation by an air stream dragging fibres from drops of melt is copied in industry to form basaltic glass wool fibres......; man-made mineral glass fibres. The basaltic melt is prevented from crystallizing due to the high cooling rate, forming the mineral glass wool fibres. Basaltic mineral wool fibres are of high interest in industry due to their good chemical durability and excellent heat and sound insulation properties...... of the information gained from the mechanical tests, fracture characteristics of individual glass fibres are imaged by scanning electron microscopy. The fracture surfaces showed to fall in three groups; 1) surfaces including fracture mirror, mist and hackle, 2) bend fracture surfaces and 3) surfaces including pores...

  3. Fibre-Optic Strain Measurement For Structural Integrity Monitoring

    NARCIS (Netherlands)

    Bruinsma, A.J.A.; Zuylen, P. van; Lamberts, C.W.; Krijger, A.J.T. de

    1984-01-01

    A method is demonstrated for monitoring the structural integrity of large structures, using an optical fibre. The strain distribution along the structure is monitored by measuring the attentuation of light along the length of the fibre.

  4. Microstructure and Mechanical Properties of Aligned Natural Fibre Composites

    DEFF Research Database (Denmark)

    Rask, Morten

    properties (stiffness-to-density ratio). The perspective of using natural fibres is to have a sustainable, biodegradable, CO2-neutral alternative to glass fibres. However, so far, it has not been possible to take full advantage of the natural fibre properties when using them for composite applications......Recently, there has been a great interest in developing and maturing natural fibre composites for structural applications. Natural fibres derived from plants such as flax and hemp have the potential to compete with traditional glass fibres as reinforcements in polymer matrices, due to good specific....... Several challenges have to be addressed and solved, many of which pertain to the fact that the fibres are sourced from a natural resource: 1) Inconsistent properties, depending on plant species, growth and harvest conditions, and fibre extraction techniques. 2) Strength values of composites are lower than...

  5. On the behaviour of gelled fibre suspensions in steady shear

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, Bettina [Unilever Corporate Research, Bedford (United Kingdom); University of Nottingham, Division of Food Sciences, Loughborough (United Kingdom); White, Duncan; Melrose, John R.; Frith, William J. [Unilever Corporate Research, Bedford (United Kingdom)

    2007-03-15

    The shear rheological properties of suspensions of gelled agar fibres in a low viscosity Newtonian matrix fluid were investigated. Two classes of fibres, low aspect ratio fibres and high aspect ratio fibres with an aspect ratio of the order of 10 and 100 respectively were included in the investigations. For all fibre phase volumes investigated, from as low as 0.01 upwards, the flow curves are characterised by an apparent yield stress followed by shear-thinning which was independent of the fibre aspect ratio. Based on our analysis of the flow curves, we conclude that the high aspect ratio fibres behave like flexible threads in contrast to the low aspect ratio fibres whose high shear relative viscosity is successfully described by a relation for long rigid rods. These findings are supported by flow visualisation using an optical shearing stage coupled to a light microscope. (orig.)

  6. The in vivo biological activity of ceramic fibres.

    Science.gov (United States)

    Brown, R C; Hoskins, J A; Glass, L R

    1995-10-01

    The well-known health effects following exposure to amphibole asbestos have led to some concern about the potential for other fibrous materials to cause similar diseases. This paper presents a summary of some of the inhalation experiments conducted with ceramic fibres in both rats and hamsters at the Research and Consulting Company, Geneva. One ceramic fibre (designated RCF1) was tested in rats at four exposure levels, this fibre was also tested in hamsters. Three other fibres were only tested in rats at the highest level--30 mg m-3. The increased incidence of tumours in these experiments has been contrasted with the negative results obtained with glass or mineral wools. However, there is evidence that the ceramic fibres were longer than the glass fibres and that long ceramic fibres were retained in lung tissue to a greater extent. This is sufficient to explain the results without recourse to explanations based on chemical differences between fibres.

  7. Rare Earth Doped Optical Fibre From Oxide Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Minati Chatterjee; Aharon Gedanken; Renata Reisfeld; Ranjan Sen; Mrinmay Pal; Milan Naskar; Mukul Paul; Shyamal Bhadra; Kamal Dasgupta; Dibyendu Ganguli; Tarun Bandyopadhyay

    2003-01-01

    Rare earth (RE) doped optical fibres were fabricated by using RE oxides coated silica nanoparticles. The fibre properties are comparable to those prepared by conventional techniques. The process offers better control over RE incorporation and homogeneity in the preform.

  8. Special Polymer Optical Fibres and Devices for Photonic Applications

    Institute of Scientific and Technical Information of China (English)

    Gang-Ding Peng

    2003-01-01

    Remarkable progresses have been made in developing special polymer optical fibres and devices for photonic applications in recent years. This presentation will mainly report on the development of electro-optic, photosensitive and photorefractive polymer optical fibres and related devices.

  9. Manufacturing Titanium Metal Matrix Composites by Consolidating Matrix Coated Fibres

    Institute of Scientific and Technical Information of China (English)

    Hua-Xin PENG

    2005-01-01

    Titanium metal matrix composites (TiMMCs) reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre (MCF) method offer optimum properties because of the resulting uniform fibre distribution, minimum fibre damage and fibre volume fraction control. In this paper, the consolidation of Ti-6Al-4V matrix-coated SiC fibres during vacuum hot pressing has been investigated. Experiments were carried out on multi-ply MCFs under vacuum hot pressing (VHP). In contrast to most of existing studies, the fibre arrangement has been carefully controlled either in square or hexagonal arraysthroughout the consolidated sample. This has enabled the dynamic consolidation behaviour of MCFs to be demonstrated by eliminating the fibre re-arrangement during the VHP process. The microstructural evolution of the matrix coating was reported and the deformation mechanisms involved were discussed.

  10. Dust processing in elliptical galaxies

    CERN Document Server

    Hirashita, Hiroyuki; Villaume, Alexa; Srinivasan, Sundar

    2015-01-01

    We reconsider the origin and processing of dust in elliptical galaxies. We theoretically formulate the evolution of grain size distribution, taking into account dust supply from asymptotic giant branch (AGB) stars and dust destruction by sputtering in the hot interstellar medium (ISM), whose temperature evolution is treated by including two cooling paths: gas emission and dust emission (i.e. gas cooling and dust cooling). With our new full treatment of grain size distribution, we confirm that dust destruction by sputtering is too efficient to explain the observed dust abundance even if AGB stars continue to supply dust grains, and that, except for the case where the initial dust-to-gas ratio in the hot gas is as high as $\\sim 0.01$, dust cooling is negligible compared with gas cooling. However, we show that, contrary to previous expectations, cooling does not help to protect the dust; rather, the sputtering efficiency is raised by the gas compression as a result of cooling. We additionally consider grain grow...

  11. Turbulence hierarchy in a random fibre laser

    Science.gov (United States)

    González, Iván R. Roa; Lima, Bismarck C.; Pincheira, Pablo I. R.; Brum, Arthur A.; Macêdo, Antônio M. S.; Vasconcelos, Giovani L.; de S. Menezes, Leonardo; Raposo, Ernesto P.; Gomes, Anderson S. L.; Kashyap, Raman

    2017-05-01

    Turbulence is a challenging feature common to a wide range of complex phenomena. Random fibre lasers are a special class of lasers in which the feedback arises from multiple scattering in a one-dimensional disordered cavity-less medium. Here we report on statistical signatures of turbulence in the distribution of intensity fluctuations in a continuous-wave-pumped erbium-based random fibre laser, with random Bragg grating scatterers. The distribution of intensity fluctuations in an extensive data set exhibits three qualitatively distinct behaviours: a Gaussian regime below threshold, a mixture of two distributions with exponentially decaying tails near the threshold and a mixture of distributions with stretched-exponential tails above threshold. All distributions are well described by a hierarchical stochastic model that incorporates Kolmogorov's theory of turbulence, which includes energy cascade and the intermittence phenomenon. Our findings have implications for explaining the remarkably challenging turbulent behaviour in photonics, using a random fibre laser as the experimental platform.

  12. TAIPAN fibre feed and spectrograph: engineering overview

    Science.gov (United States)

    Staszak, Nicholas F.; Lawrence, Jon; Zhelem, Ross; Content, Robert; Churilov, Vladimir; Case, Scott; Brown, Rebecca; Hopkins, Andrew M.; Kuehn, Kyler; Pai, Naveen; Klauser, Urs; Nichani, Vijay; Waller, Lew

    2016-07-01

    TAIPAN will conduct a stellar and galaxy survey of the Southern sky. The TAIPAN positioner is being developed as a prototype for the MANIFEST instrument on the GMT. The TAIPAN Spectrograph is an AAO designed all-refractive 2-arm design that delivers a spectral resolution of R>2000 over the wavelength range 370-870 nm. It is fed by a custom fibre cable from the TAIPAN Starbugs positioner. The design for TAIPAN incorporates 150 optical fibres (with an upgrade path to 300). Presented is an engineering overview of the UKST Fibre Cable design used to support Starbugs, the custom slit design, and the overall design and build plan for the TAIPAN Spectrograph.

  13. Development of SERS active fibre sensors

    CERN Document Server

    Polwart, E

    2002-01-01

    Surface-enhanced Raman scattering (SERS) is sensitive and selective and when coupled with fibre-optics could potentially produce an effective chemical sensing system. This thesis concerns the development of a single-fibre-based sensor, with an integral SERS-active substrate. A number of different methods for the manufacture of SERS-active surfaces on glass substrates were investigated and compared. The immobilisation of metal nanoparticles on glass functionalised with (3-aminopropyl)trimethoxysilane emerged as a suitable approach for the production of sensors. Substrates prepared by this approach were characterised using UV-visible spectroscopy, electron microscopy and Raman mapping. It was found that exposure of substrates to laser radiation led to a decrease in the signal recorded from adsorbed analytes. This speed of the decrease was shown to depend on the analyte, and the exciting wavelength and power. SERS-active fibre sensors were produced by immobilisation of silver nanoparticles at the distal end of a...

  14. Optical fibre cantilever sensor for biological application

    Science.gov (United States)

    Li, J.; Zhou, Y. X.; Patterson, G.; Shu, W. M.; Maier, R. R. J.; Fowler, R.; Hand, D. P.; MacPherson, W. N.

    2014-05-01

    Micro-cantilever sensors have shown great promise in a wide range of application are as including chemical and biological sensing. However, many of these devices are based upon a sensor `chip' that requires careful alignment between the cantilever and the read-out system, which can be challenging. Furthermore, optical interrogation typically involves a bulky free-space system. Optical fibre addressed cantilevers have been reported previously in the literature and in this paper we propose techniques to design and fabricate polymer micro-cantilevers for attachment onto the end of standard single mode fibres using laser machining. Low-cost optical sources and a fibre coupled spectrometer are employed to monitor the cantilever deflection and therefore observe biological binding between a species of interest and an activated cantilever. Proof-of-concept experiments show that the sensor is capable of detecting pathogen concentration with down to a level of 105cfu/ml.

  15. Secure Communication System Basedon Chaosin Optical Fibre

    Institute of Scientific and Technical Information of China (English)

    Pak L Chu; Fan Zhang; William Mak; Robust Lai

    2003-01-01

    @@ 1 Introduction Recently, there have been intense research activities on the study of synchronized chaos generated by fibre lasers [1] and its application to secure communication systems . So far, all studies concentrate on two aspects:[2].So far,all studies concentrate on two aspects:(1) the effect of the transmission channel between the transmitter and the receiver has been neglected, and (2)the chaos and the signal are carried by one wavelength.Both theoretical and experimental investigations make these two assumptions. In the experiments, the transmission fibre is invariably short, in the order of tens of metres. Hence its dispersion and nonlinear effects are negligible. The fibre laser responsible for the generation of chaos is often designed to lase at one wavelength only.

  16. Space Division Multiplexing in Optical Fibres

    CERN Document Server

    Richardson, D J; Nelson, L E

    2013-01-01

    Optical communications technology has made enormous and steady progress for several decades, providing the key resource in our increasingly information-driven society and economy. Much of this progress has been in finding innovative ways to increase the data carrying capacity of a single optical fibre. In this search, researchers have explored (and close to maximally exploited) every available degree of freedom, and even commercial systems now utilize multiplexing in time, wavelength, polarization, and phase to speed more information through the fibre infrastructure. Conspicuously, one potentially enormous source of improvement has however been left untapped in these systems: fibres can easily support hundreds of spatial modes, but today's commercial systems (single-mode or multi-mode) make no attempt to use these as parallel channels for independent signals.

  17. Laser acceleration... now with added fibre

    CERN Document Server

    Katarina Anthony

    2012-01-01

    Laser acceleration technology is plagued by two main issues: efficiency and repetition rates. In other words, lasers consume too much power and cannot sustain accelerating particles long enough to produce collisions. ICAN, a new EU-funded project, is examining how fibre lasers may help physicists tackle these issues.   A diode-pumped fibre laser. (Image courtesy of Laser Zentrum Hannover.) The International Coherent Amplification Network (ICAN) is studying the potential of lasers for collision physics. CERN is a beneficiary of the project and will collaborate with 15 other institutes from around the world, including KEK in Japan, Fermilab in the USA, and DESY in Germany. “The network is looking into existing fibre laser technology, which we believe has fantastic potential for accelerators,” says Gerard Mourou, ICAN co-ordinator at the École Polytechnique in France. “The hope is to make laser acceleration competitive with traditional radio-fre...

  18. Interfaces between a fibre and its matrix

    DEFF Research Database (Denmark)

    Lilholt, Hans; Sørensen, Bent F.

    2017-01-01

    The interface between a fibre and its matrix represents an important element in the characterization and exploitation of composite materials. Both theoretical models and analyses of experimental data have been presented in the literature since modern composite were developed and many experiments...... have been performed. A large volume of results for a wide range of composite systems exists, but rather little comparison and potential consistency have been reached for fibres and/or for matrices. Recently a materials mechanics approach has been presented to describe the interface by three parameters...... in polyester matrix. The analysis of existing experimental literature data is demonstrated for steel fibres in epoxy matrix and for tungsten wires in copper matrix. These latter incomplete analyses show that some results can be obtained even if all three experimental parameters are not recorded....

  19. Presynaptic calcium signalling in cerebellar mossy fibres

    Directory of Open Access Journals (Sweden)

    Louiza B Thomsen

    2010-02-01

    Full Text Available Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A TTX-sensitive fast Na+ spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers. Calcium imaging using Calcium-Green dextran revealed a stimulus-evoked all-or-none tetrodotoxin (TTX -sensitive calcium signal in simple and complex rosettes. All compartments of a complex rosette were activated during electrical activation of the mossy fibre, while individual simple and complex rosettes along an axon appeared to be isolated from one another in terms of calcium signalling. CGP55845 application showed that GABA B receptors mediated presynaptic inhibition of the calcium signal over the entire firing frequency range of mossy fibres. A paired-pulse depression of the calcium signal lasting more than one second affected burst firing in mossy fibres; this paired-pulse depression was reduced by GABA B antagonists. While our results indicated that a presynaptic rosette electrophysiologically functioned as a unit, topical GABA application showed that calcium signals in the branches of complex rosettes could be modulated locally, suggesting that cerebellar glomeruli may be dynamically sub-compartmentalized due to ongoing inhibition mediated by Golgi cells. This could provide a fine-grained control of mossy fibre-granule cell information transfer and synaptic plasticity within a mossy fibre rosette.

  20. FOAM CONCRETE REINFORCEMENT BY BASALT FIBRES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-10-01

    Full Text Available The authors demonstrate that the foam concrete performance can be improved by dispersed reinforcement, including methods that involve basalt fibres. They address the results of the foam concrete modeling technology and assess the importance of technology-related parameters. Reinforcement efficiency criteria are also provided in the article. Dispersed reinforcement improves the plasticity of the concrete mix and reduces the settlement crack formation rate. Conventional reinforcement that involves metal laths and rods demonstrates its limited application in the production of concrete used for thermal insulation and structural purposes. Dispersed reinforcement is preferable. This technology contemplates the infusion of fibres into porous mixes. Metal, polymeric, basalt and glass fibres are used as reinforcing components. It has been identified that products reinforced by polypropylene fibres demonstrate substantial abradability and deformability rates even under the influence of minor tensile stresses due to the low adhesion strength of polypropylene in the cement matrix. The objective of the research was to develop the type of polypropylene of D500 grade that would demonstrate the operating properties similar to those of Hebel and Ytong polypropylenes. Dispersed reinforcement was performed by the basalt fibre. This project contemplates an autoclave-free technology to optimize the consumption of electricity. Dispersed reinforcement is aimed at the reduction of the block settlement in the course of hardening at early stages of their operation, the improvement of their strength and other operating properties. Reduction in the humidity rate of the mix is based on the plasticizing properties of fibres, as well as the application of the dry mineralization method. Selection of optimal parameters of the process-related technology was performed with the help of G-BAT-2011 Software, developed at Moscow State University of Civil Engineering. The authors also

  1. Southern Dust Devils

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] Released 9 July 2004 The atmosphere of Mars is a dynamic system. Water-ice clouds, fog, and hazes can make imaging the surface from space difficult. Dust storms can grow from local disturbances to global sizes, through which imaging is impossible. Seasonal temperature changes are the usual drivers in cloud and dust storm development and growth. Eons of atmospheric dust storm activity has left its mark on the surface of Mars. Dust carried aloft by the wind has settled out on every available surface; sand dunes have been created and moved by centuries of wind; and the effect of continual sand-blasting has modified many regions of Mars, creating yardangs and other unusual surface forms. In our final dust devil image we are again looking at the southern hemisphere of Mars. These tracks occur mainly on the northeast side of the topographic ridges. Of course, there are many exceptions, which makes understanding the dynamics that initiate the actual dust devil cyclone difficult. Image information: VIS instrument. Latitude -47.6, Longitude 317.3 East (42.7 West). 19 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed

  2. Plentiful Dust Devils

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] Released 8 July 2004 The atmosphere of Mars is a dynamic system. Water-ice clouds, fog, and hazes can make imaging the surface from space difficult. Dust storms can grow from local disturbances to global sizes, through which imaging is impossible. Seasonal temperature changes are the usual drivers in cloud and dust storm development and growth. Eons of atmospheric dust storm activity has left its mark on the surface of Mars. Dust carried aloft by the wind has settled out on every available surface; sand dunes have been created and moved by centuries of wind; and the effect of continual sand-blasting has modified many regions of Mars, creating yardangs and other unusual surface forms. These dust devil tracks occur on the northern plains of Mars. The majority of the surface seen in the image has been affected by the passage of dust devils. Image information: VIS instrument. Latitude -54.6, Longitude 79.3 East (280.7 West). 19 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are

  3. Zeonex Microstructured Polymer Optical Fibre Bragg Grating Sensor

    DEFF Research Database (Denmark)

    Woyessa, Getinet; Fasano, Andrea; Markos, Christos

    2016-01-01

    We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time.......We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time....

  4. Fibre Bragg Grating Components for Filtering, Switching and Lasing

    OpenAIRE

    2008-01-01

    Fibre Bragg gratings (FBGs) are key components for a vast number of applications in optical communication systems, microwave photonics systems, and optical sensors, etc. The main topic of this thesis is fibre Bragg grating fabrication and applications in direct microwave optical filtering, high speed switching and switchable dual-wavelength fibre lasers. First, a brief overview is given about the photosensitivity in optical fibre, basic FBG fabrication techniques, the popular coupled-mode the...

  5. Facile synthesis of ZnO hollow fibres

    Indian Academy of Sciences (India)

    B T Su; K Wang; X W Zuo; H M Mu; N Dong; Y C Tong; J Bai; Z Q Lei

    2007-12-01

    In this paper, cotton fibres were used as bio-template to successfully synthesize new ceramic materials, ZnO hollow fibres and in an effort to explore the synthesis condition, and simplify the synthesis procedure. In this synthesis, a direct thermal decomposition of zinc acetate dihydrate coated on the surface of cotton fibres was explored. The wall porosity of the ZnO hollow fibres was controlled by changing the concentration of zinc acetate aqueous solution.

  6. Photonic Crystal Fibres - the State-of-the-Art

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Hansen, K. P.; Hansen, Theis Peter;

    2002-01-01

    Photonic crystal fibres having microstructured air-silica cross sections offer new optical properties compared to conventional fibres. These include novel guiding mechanisms, unique spectral properties and nonlinear possibilities. Recent results within the field are reviewed.......Photonic crystal fibres having microstructured air-silica cross sections offer new optical properties compared to conventional fibres. These include novel guiding mechanisms, unique spectral properties and nonlinear possibilities. Recent results within the field are reviewed....

  7. Mathematical Model for Fabrication of Micro-Structure Fibres

    Institute of Scientific and Technical Information of China (English)

    ZHOU Gui-Yao; HOU Zhi-Yun; LI Shu-Guang; HOU Lan-Tian

    2005-01-01

    @@ Using the classic principles of mechanics, we discuss the shape transformation of the micro-structure fibre preform under high temperature of the fibre drawing process, which leads to the theoretical relations among the structural diameter of the micro-structure fibre, the drawing technical parameter, and the physical constant of the microstructure fibre material. The theoretic values are basically in agreement with the experimental results.

  8. Fibre function and perception during cutaneous nerve block.

    Science.gov (United States)

    Mackenzie, R A; Burke, D; Skuse, N F; Lethlean, A K

    1975-09-01

    In awake human subjects, neural responses in radial nerves to electrical stimulation were recorded with intrafascicular tungsten microelectrodes. Changes in the activity of individual fibre groups during blocking procedures were recorded and correlated with simultaneous alterations in the perception of standardized stimuli. Light touch sensibility in hairy skin appeared to depend on the integrity of A-beta-gamma fibres, cold and pinprick on A-delta fibres, and warmth and dull pain on C fibres.

  9. Fabrication and applications of highly nonlinear silica holey fibres

    OpenAIRE

    Belardi, W.; Monro, T.M.; Price, J.H.V.; Lee, J.H.; Petropoulos, P.; Richardson, D J

    2001-01-01

    Holey fibre (HF) technology provides a new way to fabricate novel highly nonlinear silica based fibres. The cladding of a HF is defined by an arrangement of air holes that run along the fibre length surrounding a central silica core. The reduction in core size and increase in refractive index contrast that is possible in a HF allows the production of fibres with extremely high effective nonlinearity. HFs can also exhibit, by design of the hole configuration [2], dispersion properties not poss...

  10. The Significance of Defects on the Failure of Fibre Composites,

    Science.gov (United States)

    1981-12-01

    effects produced by discontinuous and kinked plies in unidirectional carbon fibre reinforced plastic under tension. The mean stress at failure on the...5 to6.5%) void contents on changes in torsional properties of carbon fibre reinforced plastic when exposed at various temperatures to dry or wet...properties of carbon fibre/Kevlar fibre reinforced plastic hybrid composites." RAE Technical Report 76057 (1976)* 15 G. Dorey, D.J. Portsmouth, Private

  11. Distribution of dust during two dust storms in Iceland

    Science.gov (United States)

    Ösp Magnúsdóttir, Agnes; Dagsson-Waldhauserova, Pavla; Arnalds, Ólafur; Ólafsson, Haraldur

    2017-04-01

    Particulate matter mass concentrations and size fractions of PM1, PM2.5, PM4, PM10, and PM15 measured in transversal horizontal profile of two dust storms in southwestern Iceland are presented. Images from a camera network were used to estimate the visibility and spatial extent of measured dust events. Numerical simulations were used to calculate the total dust flux from the sources as 180,000 and 280,000 tons for each storm. The mean PM15 concentrations inside of the dust plumes varied from 10 to 1600 ?g?m?3 (PM10 = 7 to 583 ?g?m?3). The mean PM1 concentrations were 97-241 ?g?m?3 with a maximum of 261 ?g?m?3 for the first storm. The PM1/PM2.5 ratios of >0.9 and PM1/PM10 ratios of 0.34-0.63 show that suspension of volcanic materials in Iceland causes air pollution with extremely high PM1 concentrations, similar to polluted urban areas in Europe or Asia. Icelandic volcanic dust consists of a higher proportion of submicron particles compared to crustal dust. Both dust storms occurred in relatively densely inhabited areas of Iceland. First results on size partitioning of Icelandic dust presented here should challenge health authorities to enhance research in relation to dust and shows the need for public dust warning systems.

  12. Crack Growth Monitoring by Embedded Optical Fibre Bragg Grating Sensors: Fibre Reinforced Plastic Crack Growing Detection

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira; Mikkelsen, Lars Pilgaard; McGugan, Malcolm

    2015-01-01

    This article presents a novel method to asses a crack growing/damage event in fibre reinforced plastic, or adhesive using Fibre Bragg Grating (FBG) sensors embedded in a host material. Different features of the crack mechanism that induce a change in the FBG response were identified. Double...... Cantilever Beams specimens made with glass fibre glued with structural adhesive, were instrumented with an array of FBG sensors embedded in the material and tested using an experimental fracture procedure. A digital image correlation technique was used to determine the presence of the specific phenomena...

  13. Fibre Optical Parametric Amplification in Defect Bragg Fibres with Zero Dispersion Slow Light Effect

    Institute of Scientific and Technical Information of China (English)

    XIAO Li; ZHANG Wei; HUANG Yi-Dong; PENG Jiang-De; ZHAO Hong; YANG Ke-Wu

    2008-01-01

    Nonfinearity enhancement by slow light effect and strong light confinement in defect Bragg fibres is demonstrated and analysed in applications of fibre optical parametric amplifiers. Broadband low group velocity and zero dispersion as well as the strong light confinement by band gap enhances the nonlinear coefficient up to more than one order than the conventional high nonlinear fibres.Moreover,the zero dispersion wavelength of coupled core mode can be designed arbitrarily,under which the phase-matching bandwidth of the nonlinear process can be extended.

  14. Solution electrospinning of particle-composite fibres

    DEFF Research Database (Denmark)

    Christiansen, Lasse; Fojan, Peter

    2016-01-01

    Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio.......Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio....

  15. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1998-01-01

    Durability studies are carried out at BKM as part of the research project "Design Methods for Fibre Reinforced Concrete" (FRC) involving BKM, The Concrete Research Center at DTI, Building Technology at Aalborg University, Rambøll, 4K-Beton and Rasmussen & Schiøtz. Concrete beams with or without...... structure are made on specimens drilled or sawed from beams after unloading (mechanical load). The pore structure of the concretes will be studied by microscopy, sorption and suction curves. The test programme involves three different concrete qualities (water-cement ratios). Both steel fibres (ZP...

  16. High Power Photonic Crystal Fibre Raman Laser

    Institute of Scientific and Technical Information of China (English)

    YAN Pei-Guang; RUAN Shuang-Chen; YU Yong-Qin; GUO Chun-Yu; GUO Yuan; LIU Cheng-Xiang

    2006-01-01

    A cw Raman laser based on a 100-m photonic crystal fibre is demonstrated with up to 3.8 W output power at the incident pump power of 12 W, corresponding to an optical-to-optical efficiency of about 31.6%. The second order Stokes light, which is firstly reported in a cw photonic crystal fibre Raman laser, is obtained at 1183nm with an output power of 1.6 W and a slope efficiency of about 45.7%.

  17. Spinothalamic fibres, pain conduction and cordotomy.

    Science.gov (United States)

    Moffie, D

    1975-01-01

    Description of four cases of cordotomy for intractable pain in which autopsy could be performed. In two of the cases the lesion had been placed (unintentionally) in the posterior quadrant of the spinal cord with good results as to the abolishing of pain. It is concluded that the conduction of pain and temperature stimuli is not restricted to the anterolateral part of the spinal cord but that this conduction may also take place along fibres in the posterolateral quadrant. A further conclusion is that the results of cordotomy are related to the number of cut fibres.

  18. Liquid filling of photonic crystal fibres for grating writing

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Canning, John; Lægsgaard, Jesper;

    2007-01-01

    liquid filling of photonic crystal fibres reduces the scattering from air–glass interfaces during Bragg grating writing in many layered photonic crystal fibres. Within experimental uncertainty, the grating index modulation of a grating written in germanium-doped photonic crystal fibre with 10 rings...

  19. Calculation of the conduction velocity of short nerve fibres

    NARCIS (Netherlands)

    van der Vliet, G.H.; Holsheimer, J.

    1980-01-01

    The conduction velocity v of a nerve fibre is calculated from the time delay Δ of a propagating action potential between two recording sites along the fibre. However, the conventional method of determining Δ cannot be applied to short nerve fibres. Therefore several linear signal analysis methods

  20. Optical fibre Bragg grating recorded in TOPAS cyclic olefin copolymer

    DEFF Research Database (Denmark)

    Johnson, I.P.; Yuan, Scott Wu; Stefani, Alessio

    2011-01-01

    A report is presented on the inscription of a fibre Bragg grating into a microstructured polymer optical fibre fabricated from TOPAS cyclic olefin copolymer. This material offers two important advantages over poly (methyl methacrylate), which up to now has formed the basis for polymer fibre Bragg...

  1. Design of fibre reinforced PV concepts for building integrated applications

    NARCIS (Netherlands)

    Reinders, Angelina H.M.E.; de Wit, H.; de Boer, Andries; Ossenbrink Sinke, W.; Helm, P.

    2009-01-01

    Fibre reinforced polymers present an interesting encapsulation medium for PV-modules. Glass fibres can provide increased strength and stiffness to thin polymer layers overcoming the brittleness and limited deformability of glass-panes. Glass fibre reinforced polymers allows for transparency over a

  2. Mechanical properties of short-flax-fibre reinforced compounds

    NARCIS (Netherlands)

    Bos, H.L.; Müssig, J.; Oever, van den M.J.A.

    2006-01-01

    The mechanical properties of flax/polypropylene compounds, manufactured both with a batch kneading and an extrusion process were determined and compared with the properties of Natural fibre Mat Thermoplastic (NMT) composites. The fibre length and width distributions of the fibres from the compounds

  3. Modelling fibre laydown and web uniformity in nonwoven fabric

    Science.gov (United States)

    Battocchio, F.; Sutcliffe, M. P. F.

    2017-04-01

    The mechanical and functional performance of nonwoven fabric critically depends on the fibre architecture. The fibre laydown process plays a key role in controlling this architecture. The fibre dynamic behaviour during laydown is studied through a finite element model which describes the role of the parameters in defining the area covered by a single fibre when deposited on the conveyor belt. The path taken by a fibre is described in terms of the radius of gyration, which characterises the area covered by the fibre in the textile, and the spectrum of curvature, which describes the degree of fibre looping as a function of the arc length. Starting from deterministic and idealised fibre curvature spectra, stochastic Monte Carlo simulations are undertaken to generate full nonwoven web samples and reproduce the uniformity of fibre density. A novel image analysis technique that allows measurement of the uniformity of real spunbonded nonwoven samples from images of textiles is used to confirm the validity of the model. It is shown that the main parameter that governs the fibre density uniformity is the ratio of the fibre spinning velocity to the velocity of conveyor belt, while fibre oscillations prior to deposition play a secondary role.

  4. Wet spinning of asymmetric hollow fibre membranes for gas separation

    NARCIS (Netherlands)

    Hof, van 't Jacob Adriaan

    1988-01-01

    This thesis describes the spinning and characterizatin of hollow fibre membranes for gas separation. The type of fibres studied here are made by a wet spinning process. A homogeneous solution is prepared, consisting of a polymer in a suitable organic solvent, and extruded as a hollow fibre. Both the

  5. Environmental impact assessment of man-made cellulose fibres

    NARCIS (Netherlands)

    Shen, L.; Worrell, E.; Patel, M.K.

    2010-01-01

    Man-made cellulose fibres have played an important role in the production of textile products for more than 70 years. The purpose of this study is to assess the environmental impact of man-made cellulose fibres. Life cycle assessment (LCA) was conducted for three types of fibres (i.e. Viscose, Modal

  6. Wet spinning of asymmetric hollow fibre membranes for gas separation

    NARCIS (Netherlands)

    van 't Hof, Jacob Adriaan

    1988-01-01

    This thesis describes the spinning and characterizatin of hollow fibre membranes for gas separation. The type of fibres studied here are made by a wet spinning process. A homogeneous solution is prepared, consisting of a polymer in a suitable organic solvent, and extruded as a hollow fibre. Both the

  7. Environmental impact assessment of man-made cellulose fibres

    NARCIS (Netherlands)

    Shen, L.; Worrell, E.; Patel, M.K.

    2010-01-01

    Man-made cellulose fibres have played an important role in the production of textile products for more than 70 years. The purpose of this study is to assess the environmental impact of man-made cellulose fibres. Life cycle assessment (LCA) was conducted for three types of fibres (i.e. Viscose, Modal

  8. CLEAVAGE OF SOFTWOOD KRAFT PULP FIBRES BY HCL AND CELLULASES

    Directory of Open Access Journals (Sweden)

    Paul Ander

    2008-05-01

    Full Text Available A new pulp fibre testing procedure called the HCl method was used to compare different spruce and pine fibres and mixtures of these fibres to calculate number of fibre cleavages in dislocations and other weak points. This method was compared with treatment of softwood kraft pulp fibres using different cellulase mixtures. The HCl method can distinguish between mill- and laboratory-made softwood kraft pulp fibres from the same wood batch. The sugar release is characterized by xylose and other hemicellulose sugars and little glucose. This is in contrast to cellulases, which despite strong fibre cleavage, did not distinguish between mill- and laboratory-made pulp fibres and released large amounts of glucose from the fibres. Hemicellulose degradation by HCl and deep penetration of the acid into the primary and secondary fibre cell walls at 80°C seems to be of major importance for the differentiation between mill and laboratory pulp fibres. Cellulases, in contrast, act mostly on the fibre surfaces, and deep penetration only takes place in amorphous regions of dislocations.

  9. Design of fibre reinforced PV concepts for building integrated applications

    NARCIS (Netherlands)

    Reinders, A.H.M.E.; Wit, de H.; Boer, de A.

    2009-01-01

    Fibre reinforced polymers present an interesting encapsulation medium for PV-modules. Glass fibres can provide increased strength and stiffness to thin polymer layers overcoming the brittleness and limited deformability of glass-panes. Glass fibre reinforced polymers allows for transparency over a b

  10. Biodegradable hollow fibres for the controlled release of hormones

    NARCIS (Netherlands)

    Eenink, M.J.D.; Feijen, Jan; Olijslager, J.; Albers, J.H.M.; Rieke, J.C.; Greidanus, P.J.

    1987-01-01

    Poly(l-lactide), (PLLA), hollow fibres were prepared using a dry-wet phase inversion spinning process. The effect of several spinning parameters (i.e. bore medium flow rate, spinning dope extrusion rate, fibre take-up rate, and spinning height) on the hollow fibre dimensions is reported. The use of

  11. Biodegradable hollow fibres for the controlled release of hormones

    NARCIS (Netherlands)

    Eenink, M.J.D.; Feijen, J.; Olijslager, J.; Albers, J.H.M.; Rieke, J.C.; Greidanus, P.J.

    1987-01-01

    Poly(l-lactide), (PLLA), hollow fibres were prepared using a dry-wet phase inversion spinning process. The effect of several spinning parameters (i.e. bore medium flow rate, spinning dope extrusion rate, fibre take-up rate, and spinning height) on the hollow fibre dimensions is reported. The use of

  12. Surface charges in blending short fibres with polyethylene powder

    NARCIS (Netherlands)

    Hofste, JM; Kersten, MJE; van Turnhout, J; Pennings, AJ

    1998-01-01

    Short fibres and ultra-high molecular weight polyethylene (UHMWPE) powder were mixed by swirling in a glass jar with compressed nitrogen. It was found that a kind of attraction between the fibres and UHMWPE particles is crucial for making a composite with a proper fibre distribution. If aramid and U

  13. Tensile behaviour of polyethylene and poly(p-xylylene) fibres

    NARCIS (Netherlands)

    van der Werff, Harm

    1991-01-01

    This thesis deals with the tensile behaviour of fibres prepared from high molecular weight polymers.The tensile strength of a polymeric fibre is in general much lower than the corresponding theoretical value. In case of ultra-high molecular weight polyethylene (UHMWPE), fibres can be prepared by gel

  14. Microbending in photonic crystal fibres - an ultimate loss limit?

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Hansen, Theis Peter; Hougaard, Kristian G.;

    2001-01-01

    Microbending losses are for the first time estimated in index-guiding photonic crystal fibres, and comparisons with standard step-index fibres are made. The results indicate that typical photonic crystal fibres are significantly less sensitive (one order of magnitude smaller loss) towards...

  15. Determinants and clinical application of muscle fibre conduction velocity

    NARCIS (Netherlands)

    Blijham, P.J.

    2007-01-01

    A muscle fibre can be excited by electrical stimulation using a needle electrode. Action potentials elicited this way will be conducted through the muscle fibre and can be recorded at some distance with a second needle electrode. This way, muscle fibre conduction velocity can be estimated. In the pr

  16. Nd3+ Doped Silicate Glass Photonic Crystal Fibres

    Institute of Scientific and Technical Information of China (English)

    YANG Lu-Yun; CHEN Dan-Ping; XIA Jin-An; WANG Chen; JIANG Xiong-Wei; ZHU Cong-Shan; QIU Jian-Rong

    2005-01-01

    @@ We report on the fabrication of two kinds of large core area Nd3+ doped silicate glass photonic crystal fibres, and demonstration of the fibre waveguiding properties. The measured minimum loss of one kind ofibres is 2.5 db/m at 660nm. The fibres sustain only a single mode at least over the wavelength range from 660nm to 980nm.

  17. Inhibition of starch absorption by dietary fibre. A comparative study of wheat bran, sugar-beet fibre, and pea fibre

    DEFF Research Database (Denmark)

    Hamberg, O; Rumessen, J J; Gudmand-Høyer, E

    1989-01-01

    -20%) (p less than 0.01), and 12% (5-27%) (p less than 0.01), respectively. Bread made from 100 g of low-gluten wheat flour only escaped small-bowel absorption in three subjects with a maximal fraction of 6% (p less than 0.05). All three fibres decreased mouth-to-caecum transit time. We conclude...

  18. Inhibition of starch absorption by dietary fibre. A comparative study of wheat bran, sugar-beet fibre, and pea fibre

    DEFF Research Database (Denmark)

    Hamberg, O; Rumessen, J J; Gudmand-Høyer, E

    1989-01-01

    The effect of dietary fibre on starch absorption was investigated in 8 healthy subjects. Amounts of starch escaping small-bowel absorption was assessed by comparison of breath H2 excretion after test meals and after lactulose (10g). After ingestion of bread made from 100g of wheat flour increases...

  19. [House dust mite allergy].

    Science.gov (United States)

    Carrard, A; Pichler, C

    2012-04-01

    House dust mites can be found all over the world where human beings live independent from the climate. Proteins from the gastrointestinal tract- almost all known as enzymes - are the allergens which induce chronic allergic diseases. The inhalation of small amounts of allergens on a regular base all night leads to a slow beginning of the disease with chronically stuffed nose and an exercise induced asthma which later on persists. House dust mites grow well in a humid climate - this can be in well isolated dwellings or in the tropical climate - and nourish from human skin dander. Scales are found in mattresses, upholstered furniture and carpets. The clinical picture with slowly aggravating complaints leads quite often to a delayed diagnosis, which is accidently done on the occasion of a wider spectrum of allergy skin testing. The beginning of a medical therapy with topical steroids as nasal spray or inhalation leads to a fast relief of the complaints. Although discussed in extensive controversies in the literature - at least in Switzerland with the cold winter and dry climate - the recommendation of house dust mite avoidance measures is given to patients with good clinical results. The frequent ventilation of the dwelling with cold air in winter time cause a lower indoor humidity. Covering encasings on mattresses, pillow, and duvets reduces the possibility of chronic contact with mite allergens as well as the weekly changing the bed linen. Another option of therapy is the specific immunotherapy with extracts of house dust mites showing good results in children and adults. Using recombinant allergens will show a better quality in diagnostic as well as in therapeutic specific immunotherapy.

  20. CHLORINE DIOXIDE TREATMENT OF SISAL FIBRE: SURFACE LIGNIN AND ITS INFLUENCES ON FIBRE SURFACE CHARACTERISTICS AND INTERFACIAL BEHAVIOUR OF SISAL FIBRE/PHENOLIC RESIN COMPOSITES

    Directory of Open Access Journals (Sweden)

    Linxin Zhong

    2010-11-01

    Full Text Available This paper describes an investigation of the influences of chlorine dioxide treatment on fibre surface lignin. The fibre surface characteristics and the interfacial behaviour of the sisal fibre/phenolic resin composites were also studied by SEM, AFM, and XPS. The results show that the surface of the untreated fibre contains a large amount of lignin with granular structure and non-granular structure. The surface lignin concentration is up to 51% for the untreated fibre, and then it decreases to 24% and 20% for fibres treated with 1.5 % and 2.0% chlorine dioxide, respectively. The removal of lignin from the fibre surface can enhance the interfacial strength of the composites, giving rise to increases by 36% and 28% in tensile strength and internal bonding strength. These results indicate that the surface properties of single sisal fibres can be tailored to improve the fibre/resin interface. Chlorine dioxide treatment has potential for surface modification of sisal fibre in engineering the interfacial behaviour of composites.

  1. A coal dust burner

    Energy Technology Data Exchange (ETDEWEB)

    Vakhrshev, B.M.; Khasnullin, I.G.; Krauze, Ye.G.; Ushakov, Yu.A.; Zinovyev, V.G.

    1982-01-01

    The burner for combustion of coal dust fuel, primarily, in rotating furnaces, contains coaxially disposed pipes, a branch pipe for feeding in the air mixture and a rotating mechanism. The first two pipes are switched in to an air source. The third pipe on the input end has an oblique section and the pipe may be rotated around an axis by a mechanism. The first pipe has ports and it may be moved in an axial direction. By installing the third pipe in the first and second positions, it is possible to direct the dust coming from the branch pipe along the central (the larger part of the dust) or the central pipe, respectively, which makes it possible to regulate the configuration of the torch and its temperature. Hot air is sucked from the furnace through the ports in the perforated first pipe to the mouth of the burner, which makes it possible to intensify combustion. By moving the fifitpipe to the right it is possible to overlap the ports with the projections and to rule out suction of the air. The possibility of regulating combustion in wide ranges makes it possible to reduce the expenditure of fuel by 2 to 3 percent.

  2. Dust, Climate, and Human Health

    Science.gov (United States)

    Maynard, N. G.

    2003-12-01

    Air pollution from both natural and anthropogenic causes is considered to be one of the most serious world-wide environment-related health problems, and is expected to become worse with changes in the global climate. Dust storms from the atmospheric transport of desert soil dust that has been lifted and carried by the winds - often over significant distances - have become an increasingly important emerging air quality issue for many populations. Recent studies have shown that the dust storms can cause significant health impacts from the dust itself as well as the accompanying pollutants, pesticides, metals, salt, plant debris, and other inorganic and organic materials, including viable microorganisms (bacteria, viruses and fungi). For example, thousands of tons of Asian desert sediments, some containing pesticides and herbicides from farming regions, are commonly transported into the Arctic during dust storm events. These chemicals have been identified in animal and human tissues among Arctic indigenous populations. Millions of tons of airborne desert dust are being tracked by satellite imagery, which clearly shows the magnitude as well as the temporal and spatial variability of dust storms across the "dust belt" regions of North Africa, the Middle East, and China. This paper summarizes the most recent findings on the effects of airborne desert dust on human health as well as potential climate influences on dust and health

  3. Alginate fibres containing discrete liquid filled vacuoles for controlled delivery of healing agents in fibre reinforced composites

    NARCIS (Netherlands)

    Mookhoek, S.D.; Fischer, H.R.; Zwaag, S. van der

    2012-01-01

    The work addressed involves the preparation and application of a compartmented polymer fibre, containing multiple separated domains with liquid agent for controlled release. The created fibre is a design for improvement to the existing liquid encapsulated self-healing systems such as fibre reinforce

  4. Influence of the physical structure of flax fibres on the mechanical properties of flax fibre reinforced polypropylene composites

    NARCIS (Netherlands)

    Oever, van den M.J.A.; Bos, H.L.; Kemenade, van M.J.J.M.

    2000-01-01

    This study investigates the influence of the physical structure of flax fibres on the mechanical properties of polypropylene (PP) composites. Due to their composite-like structure, flax fibres have relatively weak lateral bonds which are in particular present in flax fibres that are often used in na

  5. Design and evaluation of carbon fibre-reinforced launch packages with segmented, copper and molybdenum fibre armatures

    NARCIS (Netherlands)

    Koops, M.; Huijser, T.; Karthaus, W.

    1997-01-01

    Fibre armatures have been studied both dynamically and statically to gain insight in their electrothermal and mechanical behaviour. In the first part of this paper, the results of launch experiments with single and multi-segment copper and molybdenum fibre armatures integrated in carbon-fibre reinfo

  6. FASEP ultra-automated analysis of fibre length distribution in glass-fibre-reinforced products

    Science.gov (United States)

    Hartwich, Mark R.; Höhn, Norbert; Mayr, Helga; Sandau, Konrad; Stengler, Ralph

    2009-06-01

    Reinforced plastic materials are widely used in high sophisticated applications. The length distribution of the fibres influences the mechanical properties of the final product. A method for automatic determination of this length distribution was developed. After separating the fibres out of the composite material without any damage, and preparing them for microscopical analysis, a mosaic of microscope pictures is taken. After image processing and analysis with mathematical methods, a complete statistic of the fibre length distribution could be determined. A correlation between fibre length distribution and mechanical properties, measured e.g. with material test methods, like tensile and impact tests, was found. This is a method to optimize the process and selection of material for the plastic parts. In result this enhances customer satisfaction and, maybe much more important, reduces costs for the manufacturer.

  7. Clouds and Dust Storms

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] Released 2 July 2004 The atmosphere of Mars is a dynamic system. Water-ice clouds, fog, and hazes can make imaging the surface from space difficult. Dust storms can grow from local disturbances to global sizes, through which imaging is impossible. Seasonal temperature changes are the usual drivers in cloud and dust storm development and growth. Eons of atmospheric dust storm activity has left its mark on the surface of Mars. Dust carried aloft by the wind has settled out on every available surface; sand dunes have been created and moved by centuries of wind; and the effect of continual sand-blasting has modified many regions of Mars, creating yardangs and other unusual surface forms. This image was acquired during mid-spring near the North Pole. The linear water-ice clouds are now regional in extent and often interact with neighboring cloud system, as seen in this image. The bottom of the image shows how the interaction can destroy the linear nature. While the surface is still visible through most of the clouds, there is evidence that dust is also starting to enter the atmosphere. Image information: VIS instrument. Latitude 68.4, Longitude 180 East (180 West). 38 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote

  8. Structural Engineering Properties of Fibre Reinforced Concrete Based On Recycled Glass Fibre Polymer (GFRP)

    OpenAIRE

    Adetiloye A; Ephraim M. E

    2015-01-01

    Glass fibre reinforced plastics (GFRP) based on resin recovered from recycling plastic waste has been shown to possess mechanical properties satisfying normative requirements. This paper investigates the flexural behavior of concrete beams reinforced with GFRP produced from resin recovered from recycled plastic wastes. A total of twelve of beams of sizes 150 ×150 ×900mm and 100 × 100 × 500mm reinforced with GFRP made from recycled glass fibre reinforced polymer was tested. The fle...

  9. Hybrid Composite Structures: Multifunctionality through Metal Fibres

    NARCIS (Netherlands)

    Ahmed, T.

    2009-01-01

    The introduction of fibre reinforced polymer composites into the wings and fuselages of the newest aircraft are changing the design and manufacturing approach. Composites provide greater freedom to designers who want to improve aircraft performance in an affordable way. In this quest, researchers ar

  10. Measuring method for optical fibre sensors

    NARCIS (Netherlands)

    Lammerink, Theodorus S.J.; Fluitman, J.H.J.

    1984-01-01

    A new measuring method for the signal amplitude in intensity modulating fibre optic sensors is described. A reference signal is generated in the time domain. The method is insensitive for the sensitivity fluctuations of the light transmitter and the light receiver. The method is experimentally

  11. Multimode supercontinuum generation in chalcogenide glass fibres

    DEFF Research Database (Denmark)

    Kubat, Irnis; Bang, Ole

    2016-01-01

    Mid-infrared supercontinuum generation is considered in chalcogenide fibres when taking into account both polarisations and the necessary higher order modes. In particular we focus on high pulse energy supercontinuum generation with long pump pulses. The modeling indicates that when only a single...

  12. Kenaf Fibre Crop for Bioeconomic Industrial Development

    NARCIS (Netherlands)

    Lips, S.J.J.; Dam, van J.E.G.

    2013-01-01

    Kenaf (Hibiscus cannabinus L.) is a high yielding fibre crop that can be utilised as raw material in many industrial applications ranging from traditional fabrics,
    yarns and ropes to new applications in building materials, composites and lightweight car parts. Kenaf competes in some applications

  13. Self-compacting fibre-reinforced concrete

    NARCIS (Netherlands)

    Grunewald, S.; Walraven, J.C.

    2001-01-01

    The project 'self-compacting fibre-reinforced concrete (SCFRC)' is part of the Dutch STW/PPM program - 'cement-bonded materials' - DCT.4010. Subproject III to which the project ,SCFRC' belongs deals with the development of new high performance concretes. The project 'SCFRC' aims at investigating the

  14. Measuring method for optical fibre sensors

    NARCIS (Netherlands)

    Lammerink, T.S.J.; Fluitman, J.H.J.

    1984-01-01

    A new measuring method for the signal amplitude in intensity modulating fibre optic sensors is described. A reference signal is generated in the time domain. The method is insensitive for the sensitivity fluctuations of the light transmitter and the light receiver. The method is experimentally teste

  15. Fibre optic communications: past, present and future

    Directory of Open Access Journals (Sweden)

    B. M. Lacquet

    2000-07-01

    Full Text Available The exponential increase in the use of the Internet and the consequent growing need for higher bandwidth demand that the telecommu­nications industry expand the laid networks at a much faster rate. Optical fibre is the only transmission medium that has the potential of unlimited bandwidth and the ability to handle very high data rates.

  16. Microscopic Study on Hemp Bast Fibre Formation

    NARCIS (Netherlands)

    Hernandez, A.; Westerhuis, W.; Dam, van J.E.G.

    2007-01-01

    Commonly, fibre hemp (Cannabis sativa) is not considered for the production of soft and easy-care textiles. However, initial tests in the textile industry have shown that certain processes allow improvement in the everyday-wear characteristics of hemp textiles. In the framework of the EU R&D pro

  17. Kenaf Fibre Crop for Bioeconomic Industrial Development

    NARCIS (Netherlands)

    Lips, S.J.J.; Dam, van J.E.G.

    2013-01-01

    Kenaf (Hibiscus cannabinus L.) is a high yielding fibre crop that can be utilised as raw material in many industrial applications ranging from traditional fabrics,
    yarns and ropes to new applications in building materials, composites and lightweight car parts. Kenaf competes in some applications

  18. Radiation curing of carbon fibre composites

    Science.gov (United States)

    Spadaro, G.; Alessi, S.; Dispenza, C.; Sabatino, M. A.; Pitarresi, G.; Tumino, D.; Przbytniak, G.

    2014-01-01

    Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric. Dynamic mechanical thermal analysis was carried out in order to determine the cross-linking degree. The analysis pointed out a nonuniformity in the cross-linking degree of the e-beam cured panels, with the formation of clusters at low Tg (glass transition temperature) and clusters at high Tg. An out-of-mould post irradiation thermal treatment on e-beam cured samples provides a higher uniformity in the network although some slight degradation effects. Mode I delamination fracture toughness and Interlaminar Shear Strength (ISS) were also investigated by means of Double Cantilever Beam (DCB) and Short Beam Shear tests, respectively. Results from this mechanical characterisation allowed to correlate fracture toughness of the bulk matrix resin, cross-linking density and fibre/matrix interaction to the delamination fracture behaviour of the fibre reinforced material.

  19. Compressive Failure of Fibre Reinforced Materials

    DEFF Research Database (Denmark)

    Jensen, Henrik Myhre

    2003-01-01

    Compressive failure of uni-directional fibre composites by the kink band mechanism is analysed taking into account effects of residual stresses. Two criteria for determining the strength of the composite material have been investigated: Kink band formation at a bifurcation stress in a composite...

  20. Ceramic fibres for high temperature insulation

    Energy Technology Data Exchange (ETDEWEB)

    Padgett, G.C.

    1986-03-01

    Traditionally, refractory linings for high temperature plant and furnaces have comprised either brick or some form of concrete. In recent years, energy conservation has encouraged the greater use of high temperature insulation which is also available in either brick or a lightweight concrete. As an alternative, insulation can also be achieved using fibrous products or fibres combining low heat transfer with low heat capacity.

  1. CERN selects Fujikura's radiation resistant fibre

    CERN Multimedia

    2007-01-01

    "Fujikura today announced that its radiation resistant single mode optical fibre has been selected by CERN, the European Laboratory for Particle Physics, to provide communication links within the world's largest particle accelerator - the Large hadron Collider (LHC) - near Genevan, Switzerland. (1/2 page)

  2. Patty's toxicology. Volume 1: toxicology issues, inorganic particulates, dusts, products of biological origin and pathogens

    Energy Technology Data Exchange (ETDEWEB)

    Bingham, E.; Cohrssen, B; Powell, C.H. (eds.) [University of Cincinnati, Cincinnati, OH (US). Kettering Laboratory

    2001-07-01

    This book discusses toxic agents and pathogens in the workplace and its adverse health effects on workers. This volume includes discussions on industrial toxicology, measuring exposure to toxic substances, occupational chemical carcinogenesis, non-cancer risk assessment, gene-environment interaction, regulations and guidelines in the workplace, toxic chemical information sources, chemical safety, silica and silica compounds, asbestos, talc, rock wool and refractory ceramic fibres, fibreglass, coal, wood dust, cotton and other textile dusts, bioaerosols and disease, bloodborne pathogens in the workplace, tuberculosis and other mycobacteria and petroleum, coal tar and its related products.

  3. REINFORCING FIBRES AS PART OF TECHNOLOGY OF CONCRETES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-07-01

    It was identified that the basalt fibre consumption rate influences both the strength and the density of products made of cellular concrete. The length of the basalt fibre impacts the strength of products. A nomogram was developed to identify the consumption rate of the basalt fibre driven by the strength of products and the Portland cement consumption rate. The authors also studied the influence of the consumption rate of Portland cement and basalt fibre onto the structural quality ratio of the foamed fibre concrete.

  4. Fatigue damage propagation in unidirectional glass fibre reinforced composites

    DEFF Research Database (Denmark)

    Hansen, Jens Zangenberg; Alzamora Guzman, Vladimir Joel; Østergaard, R.C.

    2012-01-01

    Damage progression in unidirectional glass fibre reinforced composites exposed to tension fatigue is investigated, and a quantitative explanation is given for the observed stiffness loss. The stiffness degradation during fatigue is directly related to fibre breaks in the load-carrying axial fibre...... needs further attention and understanding in order to improve the fatigue life-time of glass fibre reinforced composites....... bundles. The underlying mechanisms are examined using digital microscopy, and it is postulated that fatigue damage initiates due to stress concentrations between the backing (transverse) layer and the unidirectional layer, followed by a cyclic fretting and axial fibre debonding. This fretting mechanism...

  5. The carbon fibre market and uses for composite wind blades

    Energy Technology Data Exchange (ETDEWEB)

    Lowe, J.R. [Tenax Fibers Gmbh and Co. KG, Wuppertal (Germany)

    1996-09-01

    Due to its excellent fatigue properties, low weight and high stiffness, carbon fibre reinforced plastic (CFRP) is the ideal material to use for the manufacture of wind blades. The present use of CFRP in the wind energy sector however is very low in comparison to glass fibre reinforced plastic (GFRP) materials. The main reason for this low use of CFRP is cost since at present times carbon fibre is valued ten times as much as glass fibre. This paper introduces carbon fibre as an alternative material to glass and examines the use of CFRP components in other high fatigue applications. (au)

  6. Nonreciprocal Coupling in Asymmetric Dual-Core Photonic Crystal Fibres

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lin; YANG Chang-Xi

    2004-01-01

    @@ The photonic crystal fibre with asymmetric dual cores is shown to attain strongly nonreciprocal coupling of the lightwave propagating along the fibre, for the first time to our knowledge. It is found that the coupling properties can be quite different when the incident position is changed. This kind of fibre could have potential for unidirectional coupler applications in fibre-optic local and metropolitan area networks. We also examine the polarization and wavelength dependence of the coupling nonreciprocity in the asymmetric dual-core photonic crystal fibres.

  7. A multi-purpose optical fibre sensor design for fibre reinforced composite materials

    Science.gov (United States)

    Fernando, G. F.; Liu, T.; Crosby, P.; Doyle, C.; Martin, A.; Brooks, D.; Ralph, B.; Badcock, R.

    1997-10-01

    This paper reports on the evaluation of a multi-functional extrinsic Fabry - Pérot optical fibre-based sensor design. The sensor was constructed using multimode and single mode optical fibres and a precision bore capillary tube. Fusion joints were used to secure the optical fibres into the capillary tube. The separation between the cleaved end-faces of the optical fibres defined the cavity length for the Fabry - Pérot sensor and the distance between the fusion joints defined the gauge length for this strain and temperature sensor. The sensor design was modified to: (i) monitor the progress of cure in an epoxy/amine resin system; (ii) detect the ingress of moisture in a cured epoxy/amine resin system; (iii) monitor the vibration characteristics of a pre- and post-impact damaged carbon fibre reinforced epoxy panel; and (iv) discriminate between strain and temperature measurements. The feasibility of using this type of sensor for cure monitoring, strain, temperature, residual stress measurements and damage detection in advanced fibre reinforced composites is demonstrated.

  8. From nanoparticles to fibres: effect of dispersion composition on fibre properties

    Energy Technology Data Exchange (ETDEWEB)

    Schirmer, Katharina S. U.; Esrafilzadeh, Dorna; Thompson, Brianna C.; Quigley, Anita F.; Kapsa, Robert M. I.; Wallace, Gordon G., E-mail: gwallace@uow.edu.au [University of Wollongong, ARC Centre for Electromaterials Science and Intelligent Polymer Research Institute (Australia)

    2015-06-15

    A polyvinyl alcohol (PVA)-stabilized polypyrrole nanodispersion has been optimised for conductivity and processability by decreasing the quantity of PVA before and after synthesis. A reduction of PVA before synthesis leads to the formation of particles with a slight increase in dry particle diameter (51 ± 6 to 63 ± 3 nm), and conversely a reduced hydrodynamic diameter. Conductivity of the dried nanoparticle films was not measureable after a reduction of PVA prior to synthesis. Using filtration of particles after synthesis, PVA content was sufficiently reduced to achieve dried thin film conductivity of 2 S cm{sup −1}, while the electroactivity of the dispersed particles remained unchanged. The as-synthesized and PVA-reduced polypyrrole particles were successfully spun into all-nanoparticle fibres using a wet-extrusion approach without the addition of any polymer or gel matrix. Using nanoparticles as a starting material is a novel approach, which allowed the production of macro-scale fibres that consisted entirely of polypyrrole nanoparticles. Fibres made from PVA-reduced polypyrrole showed higher electroactivity compared to fibres composed of the dispersion high in PVA. The mechanical properties of the fibres were also improved by reducing the amount of PVA present, resulting in a stronger, more ductile and less brittle fibre, which could find potential application in various fields.

  9. Effects of fibre orientation on mechanical properties of hybrid bamboo/glass fibre polymer composites

    Indian Academy of Sciences (India)

    B Stanly Jones Retnam; M Sivapragash; P Pradeep

    2014-08-01

    The usage of natural fibre as reinforcement in polymer composites have widely increased because of its enhanced properties. The usage of plant fibre cannot alone satisfy all the needs of the composites. Hence, introduction of hybrid plays a vital role in enhancing the mechanical properties of the FRP composites. Fibre orientation contributes significant role in improving the mechanical properties of the FRP composites. In this proposal, hybrid bamboo/glass fibre woven in different orientations such as 0°/90° and ± 45° was used and its effect on mechanical properties were studied. Composites containing hybrid fibres found to possess better mechanical properties, when compared to pure bamboo. In order to justify this, the following mechanical properties such as tensile, flexural, impact and hardness were investigated. SEM analysis shows the bonding between the matrix and reinforcement. All the above test results indicate that the introduction of natural bamboo fibre in glass reduces the overall cost of the composites with no compromise in strength and also attracted several studies covering green technologies.

  10. Biological durability and oxidative potential of man-made vitreous fibres as compared to crocidolite asbestos fibres

    Energy Technology Data Exchange (ETDEWEB)

    Hippeli, S.; Dornisch, K.; Elstner, E.F. [Lehrstuhl fuer Phytopathologie, Technische Univ. Muenchen-Weihenstephan, Freising-Weihenstephan (Germany); Wiethege, T.; Mueller, K.M. [Berufsgenossenschaftliche Kliniken Bergmannsheil, Universitaetsklinik, Inst. fuer Pathologie, Bochum (Germany); Gillissen, A. [Medizinische Universitaetsklinik und Poliklinik II, Kardiologie, Pneumologie, Bonn (Germany)

    2001-08-01

    In this study we investigated relationships between redox properties and biodurability of crocidolite asbestos fibres and three different man-made vitreous fibres (MMVF): traditional stone wool fibres (MMVF 21), glass fibres (MMVF 11) and refractory ceramic fibres (RCF). Each fibre type was incubated up to 22 weeks in four different incubation media: gamble solution (GS) pH 5.0 and pH 7.4, representing blood plasma without proteins, and surfactant-like solution (SLS) pH 5.0 and pH 7.4. During incubation time aliquots of incubation mixtures were removed and analysed in a biochemical model reaction, mimicking activated phagocytes. In addition, changes of fibre morphology and chemical composition were examined using SEM- and EDX-technology. In the presence of crocidolite asbestos fibres and MMVF 21 the formation of OH-radicals according to the Haber-Weiss sequence could be demonstrated, whereas MMVF 11 and RCF showed no reactivity. Crocidolite asbestos fibres exhibited a significant higher activity compared with the stone wool fibres at the onset of incubation. The oxidative capacities of these fibre types were shown to depend on both specific surface area and iron content. The oxidative potentials of crocidolite asbestos fibres as well as MMVF 21 were not constant during incubation over several weeks in each incubation medium. The reactivities showed sinoidal curves including reactivities much higher than those at the onset of incubation time. These irregular changes of oxidative capacity may be explained by changes of the redox state of fibre surface-complexed iron. Furthermore our results showed clear differences between incubation of fibres in GS and SLS, respectively, indicating that phospholipids play an important part in fibre dissolution behaviour and oxidative reactivity. (orig.)

  11. Mechanical properties of thermoplastic composites reinforced with Entada Mannii fibre

    Directory of Open Access Journals (Sweden)

    Oluwayomi BALOGUN

    2017-06-01

    Full Text Available The mechanical properties and fracture mechanisms of thermoplastic composites reinforced with Entada mannii fibres was investigated. Polypropylene reinforced with 1, 3, 5, and 7 wt% KOH treated and untreated Entada mannii fibres were processed using a compression moulding machine. The tensile properties, impact strength, and flexural properties of the composites were evaluated while the tensile fracture surface morphology was examined using scanning electron microscopy. The results show that reinforcing polypropylene with Entada mannii fibres resulted in improvement of the tensile strength and elastic modulus. This improvement is remarkable for 5 wt% KOH treated Entada mannii fibre reinforced composites by 28 % increase as compared with the unreinforced polypropylene. The composites reinforced with Entada mannii fibres also had impact strength values of 70 % higher than the unreinforced polypropylene. However, the polypropylene reinforced with 5 and 7wt% KOH treated fibres exhibited significantly higher flexural strength and Young’s modulus by 53% and 52% increase as compared with the unreinforced polypropylene. The fracture surface of the polypropylene composites reinforced with untreated Entada mannii fibres were characterized by fibre debonding, fibre pull-out and matrix yielding while less voids and fibre pull-outs are observed in the composites reinforced with KOH treated Entada mannii fibres. v

  12. Surface Treated Natural Fibres as Filler in Biocomposites

    Science.gov (United States)

    Schwarzova, I.; Stevulova, N.; Singovszka, E.; Terpakova, E.

    2015-11-01

    Biocomposites based on natural fibres as organic filler have been studied for several years because traditional building materials such as concrete are increasingly being replaced by advanced composite materials. Natural fibres are a potential replacement of glass fibres in composite materials. Inherent advantages such as low density, biodegradability and comparable specific mechanical properties make natural fibres an attractive option. However, limitations such as poor thermal stability, moisture absorption and poor compatibility with matrix are challenges that need to be resolved. The primary objective of this research was to study the effect of surface treatment on properties of hemp hurds like a natural lignocellulosic material and composites made thereof. Industrial hemp fibre is the one of the most suitable fibres for use in composite materials because of its good specific properties, as well as it being biologically degradable and CO2 neutral. Improving interfacial bonding between fibres and matrix is an important factor in using hemp fibres as reinforcement in composites. In order to improve interfacial bonding, modifications can be made to the hemp fibres to remove non- cellulosic compounds, separate hemp fibres from their bundles, and modify the fibre surface. This paper contains the comparison of FTIR spectra caused by combination of physical and chemical treatment of hemp material with unmodified sample. Modification of hemp hurds was carried out by NaOH solution and by ultrasonic treatment (deionized water and NaOH solution were used as the cleaning mediums).

  13. Aethalometer multiple scattering correction Cref for mineral dust aerosols

    Science.gov (United States)

    Di Biagio, Claudia; Formenti, Paola; Cazaunau, Mathieu; Pangui, Edouard; Marchand, Nicolas; Doussin, Jean-François

    2017-08-01

    In this study we provide a first estimate of the Aethalometer multiple scattering correction Cref for mineral dust aerosols. Cref is an empirical constant used to correct the aerosol absorption coefficient measurements for the multiple scattering artefact of the Aethalometer; i.e. the filter fibres on which aerosols are deposited scatter light and this is miscounted as absorption. The Cref at 450 and 660 nm was obtained from the direct comparison of Aethalometer data (Magee Sci. AE31) with (i) the absorption coefficient calculated as the difference between the extinction and scattering coefficients measured by a Cavity Attenuated Phase Shift Extinction analyser (CAPS PMex) and a nephelometer respectively at 450 nm and (ii) the absorption coefficient from a MAAP (Multi-Angle Absorption Photometer) at 660 nm. Measurements were performed on seven dust aerosol samples generated in the laboratory by the mechanical shaking of natural parent soils issued from different source regions worldwide. The single scattering albedo (SSA) at 450 and 660 nm and the size distribution of the aerosols were also measured. Cref for mineral dust varies between 1.81 and 2.56 for a SSA of 0.85-0.96 at 450 nm and between 1.75 and 2.28 for a SSA of 0.98-0.99 at 660 nm. The calculated mean for dust is 2.09 (±0.22) at 450 nm and 1.92 (±0.17) at 660 nm. With this new Cref the dust absorption coefficient by the Aethalometer is about 2 % (450 nm) and 11 % (660 nm) higher than that obtained by using Cref = 2.14 at both 450 and 660 nm, as usually assumed in the literature. This difference induces a change of up to 3 % in the dust SSA at 660 nm. The Cref seems to be independent of the fine and coarse particle size fractions, and so the obtained Cref can be applied to dust both close to sources and following transport. Additional experiments performed with pure kaolinite minerals and polluted ambient aerosols indicate Cref of 2.49 (±0.02) and 2.32 (±0.01) at 450 and 660 nm (SSA = 0.96-0.97) for

  14. Optimizing Saharan dust CALIPSO retrievals

    Directory of Open Access Journals (Sweden)

    V. Amiridis

    2013-06-01

    Full Text Available We demonstrate improvements in CALIPSO dust extinction retrievals over North Africa and Europe when corrections are applied regarding the Saharan dust lidar ratio assumption, the separation of dust portion in detected dust mixtures, and the averaging scheme introduced in the Level 3 CALIPSO product. First, a universal, spatially constant lidar ratio of 58 sr instead of 40 sr is applied to individual Level 2 dust-related backscatter products. The resulting aerosol optical depths show an improvement compared with synchronous and co-located AERONET measurements. An absolute bias of the order of −0.03 has been found, improving on the statistically significant biases of the order of −0.10 reported in the literature for the original CALIPSO product. When compared with the MODIS co-located AOD product, the CALIPSO negative bias is even less for the lidar ratio of 58 sr. After introducing the new lidar ratio for the domain studied, we examine potential improvements to the climatological CALIPSO Level 3 extinction product: (1 by introducing a new methodology for the calculation of pure dust extinction from dust mixtures and (2 by applying an averaging scheme that includes zero extinction values for the non-dust aerosol types detected. The scheme is applied at a horizontal spatial resolution of 1° × 1° for ease of comparison with the instantaneous and co-located dust extinction profiles simulated by the BSC-DREAM8b dust model. Comparisons show that the extinction profiles retrieved with the proposed methodology reproduce the well-known model biases per sub-region examined. The very good agreement of the proposed CALIPSO extinction product with respect to AERONET, MODIS and the BSC-DREAM8b dust model, makes this dataset an ideal candidate for the provision of an accurate and robust multi-year dust climatology over North Africa and Europe.

  15. Investigation of digital light processing using fibre-reinforced polymers

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Nielsen, Jakob Skov

    2016-01-01

    of fibre length and shape compared to layer thickness has been investigated including concepts to circumvent clustering of the fibres.This research contributes to the implementation of fibre-reinforced polymers in additive manufacturing technologies. Digital light processing allows generation...... of miniaturized objects with relatively high surface quality compared to other additive manufacturing technologies. This paper aim to move fibre reinforced resin parts one step closer towards mechanically strong production-quality components.......-reinforced polymers in digital light processing (DLP) are limited. Fibre-reinforced polymer composites were manufactured into test objects using digital light processing. Short fibres were used in an unordered manner. An anisotropic property due to fibre orientation within the material was observed. The importance...

  16. Natural Composites: Cellulose Fibres and the related Performance of Composites

    DEFF Research Database (Denmark)

    Lilholt, Hans; Madsen, Bo

    2014-01-01

    Biobased materials are becoming of increasing interest as potential structural materials for the future. A useful concept in this context is the fibre reinforcement of materials by stiff and strong fibres. The biobased resources can contribute with cellulose fibres and biopolymers. This offers...... the potential for stiff and strong biocomposite materials, but these have some limitations and obstacles to full performance. The focus will be on the ultra-structure, and the strength and stiffness of cellulose fibres, on the (unavoidable) defects causing large reductions in strength and moderate reductions...... in stiffness, on the packing ability of cellulose fibres and the related maximum fibre volume fraction in composites, on the moisture sorption of cellulose fibres and the related mass increase and (large) hygral strains induced, and on the mechanical performance of composites....

  17. Investigation of digital light processing using fibre-reinforced polymers

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Nielsen, Jakob Skov

    2016-01-01

    of fibre length and shape compared to layer thickness has been investigated including concepts to circumvent clustering of the fibres.This research contributes to the implementation of fibre-reinforced polymers in additive manufacturing technologies. Digital light processing allows generation...... of miniaturized objects with relatively high surface quality compared to other additive manufacturing technologies. This paper aim to move fibre reinforced resin parts one step closer towards mechanically strong production-quality components.......-reinforced polymers in digital light processing (DLP) are limited. Fibre-reinforced polymer composites were manufactured into test objects using digital light processing. Short fibres were used in an unordered manner. An anisotropic property due to fibre orientation within the material was observed. The importance...

  18. Mechanical Properties of Man-Made Mineral glass fibres

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    ; man-made mineral glass fibres. The basaltic melt is prevented from crystallizing due to the high cooling rate, forming the mineral glass wool fibres. Basaltic mineral wool fibres are of high interest in industry due to their good chemical durability and excellent heat and sound insulation properties...... and hence they are used for insulation products. In spite of those advantages, man made mineral wool fibres still show a certain degree of brittleness, which limits the further improvement of man made mineral wool fibres for both transportation and application. Therefore, a reduction in the brittleness...... of man made mineral wool fibres, and an improvement of the mechanical performances of man made mineral wool fibres are an evitable task for us. To do so, it is important to look into the fracture behaviour and its connection to the mechanical strength. In order to improve the understanding...

  19. Compaction in optical fibres and fibre Bragg gratings under nuclear reactor high neutron and gamma fluence

    Energy Technology Data Exchange (ETDEWEB)

    Remy, L.; Cheymol, G. [CEA, French Nuclear Energy Commission, Nuclear Energy Division, DPC/SEARS/LISL Bat 467 CEA Saclay 91191 Gif/Yvette Cedex (France); Gusarov, A. [SCK.CEN - Belgian Nuclear Research center, Boeretang 200 2400 Mol (Belgium); Morana, A.; Marin, E.; Girard, S. [Universite de Saint-Etienne, Laboratoire Hubert Curien, UMR CNRS5516, 18, rue du Pr. Lauras, F-42000 Saint-Etienne (France)

    2015-07-01

    In the framework of the development by CEA and SCK.CEN of a Fabry Perot Sensor (FPS) able to measure dimensional changes in Material Testing Reactor (MTR), the first goal of the SAKE 1 (Smirnof extention - Additional Key-tests on Elongation of glass fibres) irradiation was to measure the linear compaction of single mode fibres under high fast neutron fluence. Indeed, the compaction of the fibre which forms one side of the Fabry Perot cavity, may in particular cause a noticeable measurement error. An accurate quantification of this effect is then required to predict the radiation-induced drift and optimize the sensor design. To achieve this, an innovative approach was used. Approximately seventy uncoated fibre tips (length: 30 to 50 mm) have been prepared from several different fibre samples and were installed in the SCK.CEN BR2 reactor (Mol Belgium). After 22 days of irradiation a total fast (E > 1 MeV) fluence of 3 to 5x10{sup 19} n{sub fast}/cm{sup 2}, depending on the sample location, was accumulated. The temperature during irradiation was 291 deg. C, which is not far from the condition of the intended FPS use. A precise measurement of each fibre tip length was made before the irradiation and compared to the post irradiation measurement highlighting a decrease of the fibres' length corresponding to about 0.25% of linear compaction. The amplitude of the changes is independent of the capsule, which could mean that the compaction effect saturates even at the lowest considered fluence. In the prospect of performing distributed temperature measurement in MTR, several fibre Bragg gratings written using a femtosecond laser have been also irradiated. All the gratings were written in radiation hardened fibres, and underwent an additional treatment with a procedure enhancing their resistance to ionizing radiations. A special mounting made it possible to test the reflection and the transmission of the gratings on fibre samples cut down to 30 to 50 mm. The comparison

  20. Dust coagulation in ISM

    Science.gov (United States)

    Chokshi, Arati; Tielens, Alexander G. G. M.; Hollenbach, David

    1989-01-01

    Coagulation is an important mechanism in the growth of interstellar and interplanetary dust particles. The microphysics of the coagulation process was theoretically analyzed as a function of the physical properties of the coagulating grains, i.e., their size, relative velocities, temperature, elastic properties, and the van der Waal interaction. Numerical calculations of collisions between linear chains provide the wave energy in individual particles and the spectrum of the mechanical vibrations set up in colliding particles. Sticking probabilities are then calculated using simple estimates for elastic deformation energies and for the attenuation of the wave energy due to absorption and scattering processes.

  1. Flying Through Dust From Asteroids

    Science.gov (United States)

    Kohler, Susanna

    2016-11-01

    How can we tell what an asteroid is made of? Until now, weve relied on remote spectral observations, though NASAs recently launched OSIRIS-REx mission may soon change this by landing on an asteroid and returning with a sample.But what if we could learn more about the asteroids near Earth without needing to land on each one? It turns out that we can by flying through their dust.The aerogel dust collector of the Stardust mission. [NASA/JPL/Caltech]Ejected CluesWhen an airless body is impacted by the meteoroids prevalent throughout our solar system, ejecta from the body are flung into the space around it. In the case of small objects like asteroids, their gravitational pull is so weak that most of the ejected material escapes, forming a surrounding cloud of dust.By flying a spacecraft through this cloud, we could perform chemical analysis of the dust, thereby determining the asteroids composition. We could even capture some of the dust during a flyby (for example, by using an aerogel collector like in the Stardust mission) and bring it back home to analyze.So whats the best place to fly a dust-analyzing or -collecting spacecraft? To answer this, we need to know what the typical distribution of dust is around a near-Earth asteroid (NEA) a problem that scientists Jamey Szalay (Southwest Research Institute) and Mihly Hornyi (University of Colorado Boulder) address in a recent study.The colors show the density distribution for dust grains larger than 0.3 m around a body with a 10-km radius. The distribution is asymmetric, with higher densities on the apex side, shown here in the +y direction. [Szalay Hornyi 2016]Moon as a LaboratoryTo determine typical dust distributions around NEAs, Szalay and Hornyi first look at the distribution of dust around our own Moon, caused by the same barrage of meteorites wed expect to impact NEAs. The Moons dust cloud was measured in situ in 2013 and 2014 by the Lunar Dust Experiment (LDEX) on board the Lunar Atmosphere and Dust Environment

  2. Gravimetric dust sampling for control purposes and occupational dust sampling.

    CSIR Research Space (South Africa)

    Unsted, AD

    1997-02-01

    Full Text Available Prior to the introduction of gravimetric dust sampling, konimeters had been used for dust sampling, which was largely for control purposes. Whether or not absolute results were achievable was not an issue since relative results were used to evaluate...

  3. [Biological effect of wood dust].

    Science.gov (United States)

    Maciejewska, A; Wojtczak, J; Bielichowska-Cybula, G; Domańska, A; Dutkiewicz, J; Mołocznik, A

    1993-01-01

    The biological effect of exposure to wood dust depends on its composition and the content of microorganisms which are an inherent element of the dust. The irritant and allergic effects of wood dust have been recognised for a long time. The allergic effect is caused by the wood dust of subtropical trees, e.g. western red cedar (Thuja plicata), redwood (Sequoia sempervirens), obeche (Triplochiton scleroxylon), cocabolla (Dalbergia retusa) and others. Trees growing in the European climate such as: larch (Larix), walnut (Juglans regia), oak (Quercus), beech (Fagus), pine (Pinus) cause a little less pronounced allergic effect. Occupational exposure to irritative or allergic wood dust may lead to bronchial asthma, rhinitis, alveolitis allergica, DDTS (Organic dust toxic syndrome), bronchitis, allergic dermatitis, conjunctivitis. An increased risk of adenocarcinoma of the sinonasal cavity is an important and serious problem associated with occupational exposure to wood dust. Adenocarcinoma constitutes about half of the total number of cancers induced by wood dust. An increased incidence of the squamous cell cancers can also be observed. The highest risk of cancer applies to workers of the furniture industry, particularly those dealing with machine wood processing, cabinet making and carpentry. The cancer of the upper respiratory tract develops after exposure to many kinds of wood dust. However, the wood dust of oak and beech seems to be most carcinogenic. It is assumed that exposure to wood dust can cause an increased incidence of other cancers, especially lung cancer and Hodgkin's disease. The adverse effects of microorganisms, mainly mould fungi and their metabolic products are manifested by alveolitis allergica and ODTS. These microorganisms can induce aspergillomycosis, bronchial asthma, rhinitis and allergic dermatitis.

  4. Comparison of traditional field retting and Phlebia radiata Cel 26 retting of hemp fibres for fibre-reinforced composites.

    Science.gov (United States)

    Liu, Ming; Ale, Marcel T; Kołaczkowski, Bartłomiej; Fernando, Dinesh; Daniel, Geoffrey; Meyer, Anne S; Thygesen, Anders

    2017-12-01

    Classical field retting and controlled fungal retting of hemp using Phlebia radiata Cel 26 (a mutant with low cellulose degrading ability) were compared with pure pectinase treatment with regard to mechanical properties of the produced fibre/epoxy composites. For field retting a classification of the microbial evolution (by gene sequencing) and enzyme profiles were conducted. By phylogenetic frequency mapping, different types of fungi, many belonging to the Ascomycota phylum were found on the fibres during the first 2 weeks of field retting, and thereafter, different types of bacteria, notably Proteobacteria, also proliferated on the field retted fibres. Extracts from field retted fibres exhibited high glucanase activities, while extracts from P. radiata Cel 26 retted fibres showed high polygalacturonase and laccase activities. As a result, fungal retting gave a significantly higher glucan content in the fibres than field retting (77 vs. 67%) and caused a higher removal of pectin as indicated by lower galacturonan content of fibres (1.6%) after fibres were retted for 20 days with P. radiata Cel 26 compared to a galacturonan content of 3.6% for field retted fibres. Effective fibre stiffness increased slightly after retting with P. radiata Cel 26 from 65 to 67 GPa, while it decreased after field retting to 52 GPa. Effective fibre strength could not be determined similarly due to variations in fibre fracture strain and fibre-matrix adhesion. A maximum composite strength with 50 vol% fibres of 307 MPa was obtained using P. radiata Cel 26 compared to 248 MPa with field retting.

  5. Biological durability and oxidative potential of man-made vitreous fibres as compared to crocidolite asbestos fibres.

    Science.gov (United States)

    Hippeli, S; Dornisch, K; Wiethege, T; Gillissen, A; Müller, K M; Elstner, E F

    2001-01-01

    In this study we investigated relationships between redox properties and biodurability of crocidolite asbestos fibres and three different man-made vitreous fibres (MMVF): traditional stone wool fibres (MMVF 21), glass fibres (MMVF 11) and refractory ceramic fibres (RCF). Each fibre type was incubated up to 22 weeks in four different incubation media: gamble solution (GS) pH 5.0 and pH 7.4, representing blood plasma without proteins, and surfactant-like solution (SLS) pH 5.0 and pH 7.4. During incubation time aliquots of incubation mixtures were removed and analysed in a biochemical model reaction, mimicking activated phagocytes. In addition, changes of fibre morphology and chemical composition were examined using SEM- and EDX-technology. In the presence of crocidolite asbestos fibres and MMVF 21 the formation of OH*-radicals according to the Haber-Weiss sequence could be demonstrated, whereas MMVF 11 and RCF showed no reactivity. Crocidolite asbestos fibres exhibited a significant higher activity compared with the stone wool fibres at the onset of incubation. The oxidative capacities of these fibre types were shown to depend on both specific surface area and iron content. The oxidative potentials of crocidolite asbestos fibres as well as MMVF 21 were not constant during incubation over several weeks in each incubation medium. The reactivities showed sinoidal curves including reactivities much higher than those at the onset of incubation time. These irregular changes of oxidative capacity may be explained by changes of the redox state of fibre surface-complexed iron. Furthermore our results showed clear differences between incubation of fibres in GS and SLS, respectively, indicating that phospholipids play an important part in fibre dissolution behaviour and oxidative reactivity. In conclusion we suggest, that biodurability testing procedures should not exclusively concentrate on dissolution rates of fibres. They should include fibre characteristics concerning known

  6. Acoustical model of a Shoddy fibre absorber

    Science.gov (United States)

    Manning, John Peter

    Shoddy fibres or "Shoddies" are a mixture of post-consumer and post-industrial fibres diverted from textile waste streams and recycled into their raw fibre form. They have found widespread use as a raw material for manufacturing sound absorbers that include, but are not limited to: automotive, architectural and home appliance applications. The purpose of this project is to develop a simple acoustic model to describe the acoustic behaviour of sound absorbers composed primarily of Shoddy fibres. The model requires knowledge of the material's bulk density only. To date, these materials have not been the focus of much published research and acoustical designers must rely on models that were developed for other materials or are overly complex. For modelling purposes, an equivalent fluid approach is chosen to balance complexity and accuracy. In deriving the proposed model, several popular equivalent fluid models are selected and the required input parameters for each model identified. The models are: the model of Delaney and Bazley, two models by Miki, the model of Johnson in conjunction with the model of Champoux and Allard and the model of Johnson in conjunction with the model of Lafarge. Characterization testing is carried out on sets of Shoddy absorbers produced using three different manufacturing methods. The measured properties are open porosity, tortuosity, airflow resistivity, the viscous and thermal characteristic lengths and the static thermal permeability. Empirical relationships between model parameters and bulk density are then derived and used to populate the selected models. This yields several 'simplified' models with bulk density as the only parameter. The most accurate model is then selected by comparing each model's prediction to the results of normal incidence sound absorption tests. The model of Johnson-Lafarge populated with the empirical relations is the most accurate model over the range of frequencies considered (approx. 300 Hz - 4000 Hz

  7. Of data and dust

    CERN Multimedia

    Stephanie Hills

    2016-01-01

    The traditional image of an archive is one of dusty old boxes, books and papers. When your archive is digital, dust spells disaster. An innovative environmental sensor designed and built by a CERN IT specialist has become an essential element in the Laboratory’s data-preservation strategy.   The novel air particle monitoring sensor designed by CERN's Julien Leduc. CERN’s archive holds more than 130 petabytes of data from past and present high-energy physics experiments. Some of it is 40 years old, most of it needs to be kept forever, and all of it is held on tape cartridges (over 20,000 of them). The cartridges are held inside tape libraries with robotic arms that load them into tape drives where they can be read and written. Tape cartridges have many advantages over other data storage media, notably cost and long-term reliability, but topping the list of drawbacks is their vulnerability to contamination from airborne dust particles; a tiny piece of g...

  8. Charged Dust Aggregate Interactions

    Science.gov (United States)

    Matthews, Lorin; Hyde, Truell

    2015-11-01

    A proper understanding of the behavior of dust particle aggregates immersed in a complex plasma first requires a knowledge of the basic properties of the system. Among the most important of these are the net electrostatic charge and higher multipole moments on the dust aggregate as well as the manner in which the aggregate interacts with the local electrostatic fields. The formation of elongated, fractal-like aggregates levitating in the sheath electric field of a weakly ionized RF generated plasma discharge has recently been observed experimentally. The resulting data has shown that as aggregates approach one another, they can both accelerate and rotate. At equilibrium, aggregates are observed to levitate with regular spacing, rotating about their long axis aligned parallel to the sheath electric field. Since gas drag tends to slow any such rotation, energy must be constantly fed into the system in order to sustain it. A numerical model designed to analyze this motion provides both the electrostatic charge and higher multipole moments of the aggregate while including the forces due to thermophoresis, neutral gas drag, and the ion wakefield. This model will be used to investigate the ambient conditions leading to the observed interactions. This research is funded by NSF Grant 1414523.

  9. Mining dust filter. Bergbaustaubfilter

    Energy Technology Data Exchange (ETDEWEB)

    Igelbuescher, H.; Hoelter, H.

    1988-12-28

    A dust filter for application underground, whose casing is designed as a transportable unit combinable with further casings and fitted with removable filter pockets. These filter pockets have a frame which seals towards the casing and with the lattices on which the filter cloth is stretched and with spacers holding the said lattices at a distance. Each casing as such has inspection ports that are operationable optionally on either side, and clean and crude gas channels on its upper side. The ends of these channels have coupleable head pieces, so that connection is made easy when casings are arranged in a line. Each crude gas channel is connected to the inside of the casing by means of perforations in the floor of said channel, whereas the clean gas channel, for its part, is in connection with the inside of the casing by means of a channel on the head side of the casing. It is thus possible to create a dust filter having practically any desired output by arranging individual modules in line, in which connection each individual module is reliably transportable on the facilities available below ground, as pre-fabricated above ground. Stable support of the sides of the filter cloths is ensured by the lattice that consists of reciprocally cranked longitudinal and transverse wires. 10 figs.

  10. Sulfur in Cometary Dust

    Science.gov (United States)

    Fomenkova, M. N.

    1997-01-01

    The computer-intensive project consisted of the analysis and synthesis of existing data on composition of comet Halley dust particles. The main objective was to obtain a complete inventory of sulfur containing compounds in the comet Halley dust by building upon the existing classification of organic and inorganic compounds and applying a variety of statistical techniques for cluster and cross-correlational analyses. A student hired for this project wrote and tested the software to perform cluster analysis. The following tasks were carried out: (1) selecting the data from existing database for the proposed project; (2) finding access to a standard library of statistical routines for cluster analysis; (3) reformatting the data as necessary for input into the library routines; (4) performing cluster analysis and constructing hierarchical cluster trees using three methods to define the proximity of clusters; (5) presenting the output results in different formats to facilitate the interpretation of the obtained cluster trees; (6) selecting groups of data points common for all three trees as stable clusters. We have also considered the chemistry of sulfur in inorganic compounds.

  11. Erosion of dust aggregates

    CERN Document Server

    Seizinger, Alexander; Kley, Wilhelm

    2013-01-01

    Aims: The aim of this work is to gain a deeper insight into how much different aggregate types are affected by erosion. Especially, it is important to study the influence of the velocity of the impacting projectiles. We also want to provide models for dust growth in protoplanetary disks with simple recipes to account for erosion effects. Methods: To study the erosion of dust aggregates we employed a molecular dynamics approach that features a detailed micro-physical model of the interaction of spherical grains. For the first time, the model has been extended by introducing a new visco-elastic damping force which requires a proper calibration. Afterwards, different sample generation methods were used to cover a wide range of aggregate types. Results: The visco-elastic damping force introduced in this work turns out to be crucial to reproduce results obtained from laboratory experiments. After proper calibration, we find that erosion occurs for impact velocities of 5 m/s and above. Though fractal aggregates as ...

  12. Effect of discrete fibre reinforcement on soil tensile strength

    Directory of Open Access Journals (Sweden)

    Jian Li

    2014-04-01

    Full Text Available The tensile behaviour of soil plays a significantly important role in various engineering applications. Compacted soils used in geotechnical constructions such as dams and clayey liners in waste containment facilities can suffer from cracking due to tensile failure. In order to increase soil tensile strength, discrete fibre reinforcement technique was proposed. An innovative tensile apparatus was developed to determine the tensile strength characteristics of fibre reinforced soil. The effects of fibre content, dry density and water content on the tensile strength were studied. The results indicate that the developed test apparatus was applicable in determining tensile strength of soils. Fibre inclusion can significantly increase soil tensile strength and soil tensile failure ductility. The tensile strength basically increases with increasing fibre content. As the fibre content increases from 0% to 0.2%, the tensile strength increases by 65.7%. The tensile strength of fibre reinforced soil increases with increasing dry density and decreases with decreasing water content. For instance, the tensile strength at a dry density of 1.7 Mg/m3 is 2.8 times higher than that at 1.4 Mg/m3. It decreases by 30% as the water content increases from 14.5% to 20.5%. Furthermore, it is observed that the tensile strength of fibre reinforced soil is dominated by fibre pull-out resistance, depending on the interfacial mechanical interaction between fibre surface and soil matrix.

  13. Mechanical properties of natural fibre reinforced polymer composites

    Indian Academy of Sciences (India)

    A S Singha; Vijay Kumar Thakur

    2008-10-01

    During the last few years, natural fibres have received much more attention than ever before from the research community all over the world. These natural fibres offer a number of advantages over traditional synthetic fibres. In the present communication, a study on the synthesis and mechanical properties of new series of green composites involving Hibiscus sabdariffa fibre as a reinforcing material in urea–formaldehyde (UF) resin based polymer matrix has been reported. Static mechanical properties of randomly oriented intimately mixed Hibiscus sabdariffa fibre reinforced polymer composites such as tensile, compressive and wear properties were investigated as a function of fibre loading. Initially urea–formaldehyde resin prepared was subjected to evaluation of its optimum mechanical properties. Then reinforcing of the resin with Hibiscus sabdariffa fibre was accomplished in three different forms: particle size, short fibre and long fibre by employing optimized resin. Present work reveals that mechanical properties such as tensile strength, compressive strength and wear resistance etc of the urea–formaldehyde resin increases to considerable extent when reinforced with the fibre. Thermal (TGA/DTA/DTG) and morphological studies (SEM) of the resin and biocomposites have also been carried out.

  14. Effect of discrete fibre reinforcement on soil tensile strength

    Institute of Scientific and Technical Information of China (English)

    Jian Li; Chaosheng Tang; Deying Wang; Xiangjun Pei; Bin Shi

    2014-01-01

    The tensile behaviour of soil plays a significantly important role in various engineering applications. Compacted soils used in geotechnical constructions such as dams and clayey liners in waste containment facilities can suffer from cracking due to tensile failure. In order to increase soil tensile strength, discrete fibre reinforcement technique was proposed. An innovative tensile apparatus was developed to deter-mine the tensile strength characteristics of fibre reinforced soil. The effects of fibre content, dry density and water content on the tensile strength were studied. The results indicate that the developed test apparatus was applicable in determining tensile strength of soils. Fibre inclusion can significantly in-crease soil tensile strength and soil tensile failure ductility. The tensile strength basically increases with increasing fibre content. As the fibre content increases from 0%to 0.2%, the tensile strength increases by 65.7%. The tensile strength of fibre reinforced soil increases with increasing dry density and decreases with decreasing water content. For instance, the tensile strength at a dry density of 1.7 Mg/m3 is 2.8 times higher than that at 1.4 Mg/m3. It decreases by 30% as the water content increases from 14.5% to 20.5%. Furthermore, it is observed that the tensile strength of fibre reinforced soil is dominated by fibre pull-out resistance, depending on the interfacial mechanical interaction between fibre surface and soil matrix.

  15. Applicability of the Waste Fibres in Cement Paste

    Directory of Open Access Journals (Sweden)

    Regina KALPOKAITĖ DIČKUVIENĖ

    2013-09-01

    Full Text Available Fibres produced from waste catalyst together with commercially available polypropylene fibres were incorporated into ordinary Portland cement paste. The effects of fibre content as well as a mix of different type of fibres on mechanical and physical properties of wet and dry samples were investigated. The results showed that presence of fibres reduced compressive strength of the plain cement in wet and dry state. Contrary, when the combination of 1.5 wt% waste and 1.5 wt% polypropylene fibres was used flexural strength of cement mixture increased by up to 9 % at the age of 28 days. It was observed that addition of 1.5 wt% of only waste fibres improved flexural strength after long hydration period as well. However, the lowest mechanical strength results showed samples with 3 wt% of waste fibres. It was also observed that higher content of waste fibres reduced porosity of the cement mixture and consequently, decreased water absorption capacity. Presence of fibres reduced drying shrinkage of samples and they were lower than plain cement after 28 days of hydration. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.1992

  16. Strength and toughness of structural fibres for composite material reinforcement.

    Science.gov (United States)

    Herráez, M; Fernández, A; Lopes, C S; González, C

    2016-07-13

    The characterization of the strength and fracture toughness of three common structural fibres, E-glass, AS4 carbon and Kevlar KM2, is presented in this work. The notched specimens were prepared by means of selective carving of individual fibres by means of the focused ion beam. A straight-fronted edge notch was introduced in a plane perpendicular to the fibre axis, with the relative notch depth being a0/D≈0.1 and the notch radius at the tip approximately 50 nm. The selection of the appropriate beam current during milling operations was performed to avoid to as much as possible any microstructural changes owing to ion impingement. Both notched and un-notched fibres were submitted to uniaxial tensile tests up to failure. The strength of the un-notched fibres was characterized in terms of the Weibull statistics, whereas the residual strength of the notched fibres was used to determine their apparent toughness. To this end, the stress intensity factor of a fronted edge crack was computed by means of the finite-element method for different crack lengths. The experimental results agreed with those reported in the literature for polyacrylonitrile-based carbon fibres obtained by using similar techniques. After mechanical testing, the fracture surface of the fibres was analysed to ascertain the failure mechanisms. It was found that AS4 carbon and E-glass fibres presented the lower toughness with fracture surfaces perpendicular to the fibre axis, emanating from the notch tip. The fractured region of Kevlar KM2 fibres extended along the fibre and showed large permanent deformation, which explains their higher degree of toughness when compared with carbon and glass fibres. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'.

  17. Comparison of cytotoxicity of man-made vitreous fibres.

    Science.gov (United States)

    Luoto, K; Holopainen, M; Sarataho, M; Savolainen, K

    1997-01-01

    The purpose of the study was to compare the cytotoxicity of man-made vitreous fibres (MMVFs): four refractory ceramic fibres (RCFs 1-4), two glasswool fibres (MMVF 10 and 11), a rockwool fibre (MMVF 21) and a slagwool fibre (MMVF 22). The ability of the fibres to induce haemolysis in sheep erythrocytes, to release lactate dehydrogenase (LDH) from rat alveolar macrophages (AM) and to increase the production of reactive oxygen metabolites (ROMs) in human polymorphonuclear leukocytes (PML) was studied. To assess the relative cytotoxicity of MMVFs, their toxicity was compared with that induced by quartz, chrysotile or titanium dioxide. MMVFs induced a modest, but dose-dependent, increase of haemolysis at doses of 0.5, 2.5 and 5.0 mg ml-1. The amount of haemolysis and LDH release induced by MMVFs was generally similar to that induced by titanium dioxide. Glasswool fibre MMVF 10 induced less LDH release from rat AM than rockwool MMVF 21 or slagwool MMVF 22 fibres, whereas glasswool fibre MMVF 11 induced less LDH release than slagwool fibre MMVF 22 (P < 0.05). All fibres also dose-dependently increased the production of ROMs at doses between 25 and 500 micrograms ml-1. The shapes of the time-courses of MMVF-induced production of ROMs suggest that the mechanisms whereby the different fibres induce ROM production may exhibit similar features. There are clear-cut differences in the potency of various MMVFs to induce cytotoxicity and oxidative burst. The present results also emphasize the importance of using several measures of toxicity when assessing the biological activity of various fibres in vitro.

  18. Andromeda's dust

    Energy Technology Data Exchange (ETDEWEB)

    Draine, B. T.; Aniano, G. [Princeton University Observatory, Peyton Hall, Princeton, NJ 08544-1001 (United States); Krause, Oliver; Groves, Brent; Sandstrom, Karin; Klaas, Ulrich; Linz, Hendrik; Rix, Hans-Walter; Schinnerer, Eva; Schmiedeke, Anika; Walter, Fabian [Max-Planck-Institut fur Astronomie, Konigstuhl 17, D-69117 Heidelberg (Germany); Braun, Robert [CSIRO—Astronomy and Space Science, P.O. Box 76, Epping, NWS 1710 (Australia); Leroy, Adam, E-mail: draine@astro.princeton.edu, E-mail: ganiano@ias.u-psud.fr [National Radio Astronomy Observatory, 520 Edgemont Road, Charlottesville, VA 22903 (United States)

    2014-01-10

    Spitzer Space Telescope and Herschel Space Observatory imaging of M31 is used, with a physical dust model, to construct maps of dust surface density, dust-to-gas ratio, starlight heating intensity, and polycyclic aromatic hydrocarbon (PAH) abundance, out to R ≈ 25 kpc. The global dust mass is M {sub d} = 5.4 × 10{sup 7} M {sub ☉}, the global dust/H mass ratio is M {sub d}/M {sub H} = 0.0081, and the global PAH abundance is (q {sub PAH}) = 0.039. The dust surface density has an inner ring at R = 5.6 kpc, a maximum at R = 11.2 kpc, and an outer ring at R ≈ 15.1 kpc. The dust/gas ratio varies from M {sub d}/M {sub H} ≈ 0.026 at the center to ∼0.0027 at R ≈ 25 kpc. From the dust/gas ratio, we estimate the interstellar medium metallicity to vary by a factor ∼10, from Z/Z {sub ☉} ≈ 3 at R = 0 to ∼0.3 at R = 25 kpc. The dust heating rate parameter (U) peaks at the center, with (U) ≈ 35, declining to (U) ≈ 0.25 at R = 20 kpc. Within the central kiloparsec, the starlight heating intensity inferred from the dust modeling is close to what is estimated from the stars in the bulge. The PAH abundance reaches a peak q {sub PAH} ≈ 0.045 at R ≈ 11.2 kpc. When allowance is made for the different spectrum of the bulge stars, q {sub PAH} for the dust in the central kiloparsec is similar to the overall value of q {sub PAH} in the disk. The silicate-graphite-PAH dust model used here is generally able to reproduce the observed dust spectral energy distribution across M31, but overpredicts 500 μm emission at R ≈ 2-6 kpc, suggesting that at R = 2-6 kpc, the dust opacity varies more steeply with frequency (with β ≈ 2.3 between 200 and 600 μm) than in the model.

  19. Dust and the Sick Building Syndrome

    DEFF Research Database (Denmark)

    Gyntelberg, Finn; Suadicani, Poul; Wohlfahrt Nielsen, Jan

    1994-01-01

    Farmakologi, bacteria, dust, histamine, disease, gram-negative, indoor climate, sick building syndrome......Farmakologi, bacteria, dust, histamine, disease, gram-negative, indoor climate, sick building syndrome...

  20. LHCb Scintillating Fibre Tracker Engineering Design Review Report: Fibres, Mats and Modules

    CERN Document Server

    Joram, Christian; Leverington, Blake Dean; Kirn, Thomas; Bachmann, Sebastian; Ekelhof, Robert Jan; Müller, Janine

    2015-01-01

    During the Long Shutdown 2 of the LHC, the LHCb collaboration will replace the current Outer and Inner Tracker by a single tracking detector, based on 2.42m long scintillating fibres with a diameter of 250 $\\mu$m, readout by silicon photo-multipliers (SiPM). The fibers are arranged in mats of 6 fibre-layers with a width of 130.65 mm. Eight fibre mats will form a module and are sandwiched between honeycomb and carbon fibre composite panels to provide stability and support over the module length of 4.85m. At either end of the module are the interfaces to the SiPMs and the front-end electronics. The active detection area of the Scintillating Fiber Tracker (SciFi) of 360m$^2$ will comprise 144 single modules arranged in 12 detection planes. This document summarizes the engineering design of the fibre mats and of the modules including the interfaces to the SiPMs and the mounting to the detector frames. Mechanical and detector properties of several prototype modules are discussed. The production procedure of the fi...

  1. A viscoelastic-viscoplastic model for short-fibre reinforced polymers with complex fibre orientations

    Directory of Open Access Journals (Sweden)

    Nciri M.

    2015-01-01

    Full Text Available This paper presents an innovative approach for the modelling of viscous behaviour of short-fibre reinforced composites (SFRC with complex distributions of fibre orientations and for a wide range of strain rates. As an alternative to more complex homogenisation methods, the model is based on an additive decomposition of the state potential for the computation of composite’s macroscopic behaviour. Thus, the composite material is seen as the assembly of a matrix medium and several linear elastic fibre media. The division of short fibres into several families means that complex distributions of orientation or random orientation can be easily modelled. The matrix behaviour is strain-rate sensitive, i.e. viscoelastic and/or viscoplastic. Viscoelastic constitutive laws are based on a generalised linear Maxwell model and the modelling of the viscoplasticity is based on an overstress approach. The model is tested for the case of a polypropylene reinforced with short-glass fibres with distributed orientations and subjected to uniaxial tensile tests, in different loading directions and under different strain rates. Results demonstrate the efficiency of the model over a wide range of strain rates.

  2. PERSPECTIVE: Dust, fertilization and sources

    Science.gov (United States)

    Remer, Lorraine A.

    2006-11-01

    Aerosols, tiny suspended particles in the atmosphere, play an important role in modifying the Earth's energy balance and are essential for the formation of cloud droplets. Suspended dust particles lifted from the world's arid regions by strong winds contain essential minerals that can be transported great distances and deposited into the ocean or on other continents where productivity is limited by lack of usable minerals [1]. Dust can transport pathogens as well as minerals great distance, contributing to the spread of human and agricultural diseases, and a portion of dust can be attributed to human activity suggesting that dust radiative effects should be included in estimates of anthropogenic climate forcing. The greenish and brownish tints in figure 1 show the wide extent of monthly mean mineral dust transport, as viewed by the MODerate resolution Imaging Spectroradiometer (MODIS) satellite sensor. The monthly mean global aerosol system for February 2006 from the MODIS aboard the Terra satellite Figure 1. The monthly mean global aerosol system for February 2006 from the MODIS aboard the Terra satellite. The brighter the color, the greater the aerosol loading. Red and reddish tints indicate aerosol dominated by small particles created primarily from combustion processes. Green and brownish tints indicate larger particles created from wind-driven processes, usually transported desert dust. Note the bright green band at the southern edge of the Saharan desert, the reddish band it must cross if transported to the southwest and the long brownish transport path as it crosses the Atlantic to South America. Image courtesy of the NASA Earth Observatory (http://earthobservatory.nasa.gov). Even though qualitatively we recognize the extent and importance of dust transport and the role that it plays in fertilizing nutrient-limited regions, there is much that is still unknown. We are just now beginning to quantify the amount of dust that exits one continental region and the

  3. Presynaptic calcium signalling in cerebellar mossy fibres

    DEFF Research Database (Denmark)

    Thomsen, Louiza Bohn; Jörntell, Henrik; Midtgaard, Jens

    2010-01-01

    Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A tetrodotoxin (TTX....... Calcium imaging using Calcium-Green dextran revealed a stimulus-evoked all-or-none TTX-sensitive calcium signal in simple and complex rosettes. All compartments of a complex rosette were activated during electrical activation of the mossy fibre, while individual simple and complex rosettes along an axon......)-sensitive fast Na(+) spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers...

  4. Fibre Optic Sensors for Selected Wastewater Characteristics

    Directory of Open Access Journals (Sweden)

    Sulaiman W. Harun

    2013-07-01

    Full Text Available Demand for online and real-time measurements techniques to meet environmental regulation and treatment compliance are increasing. However the conventional techniques, which involve scheduled sampling and chemical analysis can be expensive and time consuming. Therefore cheaper and faster alternatives to monitor wastewater characteristics are required as alternatives to conventional methods. This paper reviews existing conventional techniques and optical and fibre optic sensors to determine selected wastewater characteristics which are colour, Chemical Oxygen Demand (COD and Biological Oxygen Demand (BOD. The review confirms that with appropriate configuration, calibration and fibre features the parameters can be determined with accuracy comparable to conventional method. With more research in this area, the potential for using FOS for online and real-time measurement of more wastewater parameters for various types of industrial effluent are promising.

  5. Optical Fibre Dosimeter for SASE FEL Undulators

    CERN Document Server

    Körfer, M

    2003-01-01

    Single pass Free Electron Lasers (FELs) based on self-amplified spontaneous emission (SASE) are developed for high brightness and short wavelength applications. They use permanent magnet undulators which are radiation sensitive devices. During accelerator commissioning beam losses can appear anywhere along the undulator line. To avoid damage of the permanent magnets due to radiation, an optical fibre dosimeter system can be used. The increase of absorption caused by ionizing radiation is measured in radiation sensitive optical fibers. The dose system enables relatively fast particle loss tuning during accelerator operation and allows the monitoring of the accumulated dose. Dose measurements in narrow gaps which are inaccessible for any other (online) dosimeter type become possible. The electromagnetic insensitivity of optical fibre sensor is an advantage of applications in strong magnetic undulator fields. At each location the light absorption is measured by using an optical power-meter. The dynamic range is ...

  6. Global Embedding of Fibre Inflation Models

    CERN Document Server

    Cicoli, Michele; Shukla, Pramod

    2016-01-01

    We present concrete embeddings of fibre inflation models in globally consistent type IIB Calabi-Yau orientifolds with closed string moduli stabilisation. After performing a systematic search through the existing list of toric Calabi-Yau manifolds, we find several examples that reproduce the minimal setup to embed fibre inflation models. This involves Calabi-Yau manifolds with $h^{1,1}= 3$ which are K3 fibrations over a $\\mbb{P}^1$ base with an additional shrinkable rigid divisor. We then provide different consistent choices of the underlying brane set-up which generate a non-perturbative superpotential suitable for moduli stabilisation and string loop corrections with the correct form to drive inflation. For each Calabi-Yau orientifold setting, we also compute the effect of higher derivative contributions and study their influence on the inflationary dynamics.

  7. Single-Mode Soft Glass Fibres

    Science.gov (United States)

    Jedrzejewski, Kazimierz

    1990-01-01

    The technology of single-mode optical soft glass fibres is developed. The well-known rod in tube technique with multiple sleeving was taken to achieve proper dimensions. The ultrasonic mill-drill was used to prepare different structures: high ▵ , high birefringent, D-shaped, multicore, metal wire/glass compound and doped. The temperature processes were carried out very carefully to avoid glass decomposition. The geometry, refractive index profiles, mode near field patterns and λc agreed with the predicted and material data. The losses were reasonably low, better then 370 dB/km (800 nm). The enhanced Verdet constants and nonlinear coefficients values, high dopants levels and other special properties including low process temperatures are very attractive for fibre short range applications, sensors and devices e.g. polarizers, couplers, lasers, filters.

  8. Creep Strength of Discontinuous Fibre Composites

    DEFF Research Database (Denmark)

    Pedersen, Ole Bøcker

    1974-01-01

    relation between stress and strain rate. Expressions for the interface stress, the creep velocity profile adjacent to the fibres and the creep strength of the composite are derived. Previous results for the creep strength, sc = aVfs0 ( \\frac[( Î )\\dot] [( Î )\\dot] 0 )1/nr1 + 1/n c=Vf001n1+1n in which[( Î...... )\\dot] is the composite creep rate,V f is the fibre volume fraction,sgr 0,epsi 0 andn are the constants in the matrix creep law. The creep strength coefficient agr is found to be very weakly dependent onV f and practically independent ofn whenn is greater than about 6....

  9. Retention of Cationic Starch onto Cellulose Fibres

    Science.gov (United States)

    Missaoui, Mohamed; Mauret, Evelyne; Belgacem, Mohamed Naceur

    2008-08-01

    Three methods of cationic starch titration were used to quantify its retention on cellulose fibres, namely: (i) the complexation of CS with iodine and measurement of the absorbency of the ensuing blue solution by UV-vis spectroscopy; (ii) hydrolysis of the starch macromolecules followed by the conversion of the resulting sugars to furan-based molecules and quantifying the ensuing mixture by measuring their absorbance at a Ι of 490 nm, using the same technique as previous one and; finally (iii) hydrolysis of starch macromolecules by trifluoro-acetic acid and quantification of the sugars in the resulting hydrolysates by high performance liquid chromatography. The three methods were found to give similar results within the range of CS addition from 0 to 50 mg per g of cellulose fibres.

  10. Fibre optic sensors for selected wastewater characteristics.

    Science.gov (United States)

    Chong, Su Sin; Aziz, A R Abdul; Harun, Sulaiman W

    2013-07-05

    Demand for online and real-time measurements techniques to meet environmental regulation and treatment compliance are increasing. However the conventional techniques, which involve scheduled sampling and chemical analysis can be expensive and time consuming. Therefore cheaper and faster alternatives to monitor wastewater characteristics are required as alternatives to conventional methods. This paper reviews existing conventional techniques and optical and fibre optic sensors to determine selected wastewater characteristics which are colour, Chemical Oxygen Demand (COD) and Biological Oxygen Demand (BOD). The review confirms that with appropriate configuration, calibration and fibre features the parameters can be determined with accuracy comparable to conventional method. With more research in this area, the potential for using FOS for online and real-time measurement of more wastewater parameters for various types of industrial effluent are promising.

  11. 2D Saturable Absorbers for Fibre Lasers

    Directory of Open Access Journals (Sweden)

    Robert I. Woodward

    2015-11-01

    Full Text Available Two-dimensional (2D nanomaterials are an emergent and promising platform for future photonic and optoelectronic applications. Here, we review recent progress demonstrating the application of 2D nanomaterials as versatile, wideband saturable absorbers for Q-switching and mode-locking fibre lasers. We focus specifically on the family of few-layer transition metal dichalcogenides, including MoS2, MoSe2 and WS2.

  12. Elastic fibres and vascular structure in hypertension.

    Science.gov (United States)

    Arribas, Silvia M; Hinek, Aleksander; González, M Carmen

    2006-09-01

    Blood vessels are dynamic structures composed of cells and extracellular matrix (ECM), which are in continuous cross-talk with each other. Thus, cellular changes in phenotype or in proliferation/death rate affect ECM synthesis. In turn, ECM elements not only provide the structural framework for vascular cells, but they also modulate cellular function through specific receptors. These ECM-cell interactions, together with neurotransmitters, hormones and the mechanical forces imposed by the heart, modulate the structural organization of the vascular wall. It is not surprising that pathological states related to alterations in the nervous, humoral or haemodynamic environment-such as hypertension-are associated with vascular wall remodeling, which, in the end, is deleterious for cardiovascular function. However, the question remains whether these structural alterations are simply a consequence of the disease or if there are early cellular or ECM alterations-determined either genetically or by environmental factors-that can predispose to vascular remodeling independent of hypertension. Elastic fibres might be key elements in the pathophysiology of hypertensive vascular remodeling. In addition to the well known effects of hypertension on elastic fibre fatigue and accelerated degradation, leading to loss of arterial wall resilience, recent investigations have highlighted new roles for individual components of elastic fibres and their degradation products. These elements can act as signal transducers and regulate cellular proliferation, migration, phenotype, and ECM degradation. In this paper, we review current knowledge regarding components of elastic fibres and discuss their possible pathomechanistic associations with vascular structural abnormalities and with hypertension development or progression.

  13. Fabrication of Polymer Optical Fibre (POF Gratings

    Directory of Open Access Journals (Sweden)

    Yanhua Luo

    2017-03-01

    Full Text Available Gratings inscribed in polymer optical fibre (POF have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

  14. Fibre suspension flocculation under simulated forming conditions

    OpenAIRE

    Yan, Huawei

    2004-01-01

    A flow loop system for study of fibre flocculation insuspensions has been developed. The system is designed tosimulate the flow conditions in a paper machine headbox. It isequipped with a radial distributor feeding a step diffuser pipepackage, after which the flow is contracted in a 2-D nozzle.The flow system is also equipped with a secondary flowcontraction with an area reduction ratio of 2:1 after theheadbox nozzle, mimicking accelerations that may take placeduring forming. The flow system ...

  15. Co-extrusion of piezoelectric ceramic fibres

    OpenAIRE

    Ismael Michen, Marina

    2011-01-01

    The present work successfully developed a methodology for fabricating lead zirconate titanate [PZT] thin solid- and hollow-fibres by the thermoplastic co-extrusion process. The whole process chain, that includes: a) compounding, involving the mixing of ceramic powder with a thermoplastic binder, b) rheological characterizations, c) preform composite fabrication followed by co-extrusion, d) debinding and, finally, e) sintering of the body to near full density, is systematical...

  16. Fibre optic sensors for mine hazard detection

    Energy Technology Data Exchange (ETDEWEB)

    Liu, T; Wang, C; Wei, Y; Zhao, Y; Shang, Y; Wang, Z [Laser Institute of Shandong Academy of Science (China); Huo, D [Shandong Micro-Sensor Photonics Limited, 19 Keyuan Road, Jinan, Shandong province, 250014 (China); Ning, Y, E-mail: tongyuliu@hotmail.co [Intelligent Sensor Systems Limited, Rockley Manor, Rockley, Wiltshire (United Kingdom)

    2009-07-01

    We report the development of a comprehensive safety monitoring solution for coal mines. A number of fibre optic sensors have been developed and deployed for safety monitoring of mine roof integrity and hazardous gases. The FOS-based mine hazard detection system offers unique advantages of intrinsic safety, multi-location and multi-parameter monitoring. They can be potentially used to build expert systems for mine hazard early detection and prevention.

  17. Spider's web inspires fibres for industry

    Science.gov (United States)

    Dacey, James

    2010-03-01

    Spiders may not be everybody's idea of natural beauty, but nobody can deny the artistry in the webs that they spin, especially when decorated with water baubles in the morning dew. Inspired by this spectacle, a group of researchers in China has mimicked the structural properties of the spider's web to create a fibre for industry that can manipulate water with the same skill and efficiency, writes James Dacey.

  18. Applications for fibre-reinforced plastic

    Energy Technology Data Exchange (ETDEWEB)

    Teuschler, V. [Fiberdur-Vanck (Germany)

    1999-07-01

    The outstanding mechanical properties of fibre-reinforced plastic are extolled. It has strength comparable with that of steel, and other physical properties that give it advantages over ferrous materials for use in pipelines, shipbuilding and offshore conduits. It has well established uses in aircraft, automobiles and boats and is probably more resistant to weathering and corrosion than any other material. The electricity-conducting Navicon pipe, the Fiberdur-vinyl ester/epoxy system and the Fiberdur-DOS system are described.

  19. Fibre suspension flocculation under simulated forming conditions

    OpenAIRE

    Yan, Huawei

    2004-01-01

    A flow loop system for study of fibre flocculation insuspensions has been developed. The system is designed tosimulate the flow conditions in a paper machine headbox. It isequipped with a radial distributor feeding a step diffuser pipepackage, after which the flow is contracted in a 2-D nozzle.The flow system is also equipped with a secondary flowcontraction with an area reduction ratio of 2:1 after theheadbox nozzle, mimicking accelerations that may take placeduring forming. The flow system ...

  20. PROFITABILITY OF INCREMENTAL EXPENDITURE ON FIBRE PROMOTION

    OpenAIRE

    Hill, Debbie J.; Piggott, Roley R.; Griffith, Garry R.

    1996-01-01

    In this paper the impact of changes in wool promotion expenditure and changes in expenditure on the promotion of competing fibres are examined using an equilibrium displacement model. The emphasis is on examining impacts on producer profits net of promotion expenditure and on benefit-cost ratios measuring changes in producer surplus relative to changes in promotion expenditure. It was found, for example, that incremental expenditure on apparel wool promotion on the domestic market is unprofit...

  1. Optical fibre cable selection for electricity utilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The report provides an assessment of the range of optical fibre cable solutions available, by type e.g. OPGW, ADSS, rather than by design. it also examines the key issues which will influence an electricity utilities decisions and proposes a method of evaluating the options to identify the one which most closely matches the utility's critical needs, with measurements against time, cost and quality targets. (author)

  2. Life cycle assessment of sisal fibre – Exploring how local practices can influence environmental performance

    NARCIS (Netherlands)

    Broeren, Martijn L M; Dellaert, Stijn N C; Cok, Benjamin; Patel, Martin K.; Worrell, Ernst; Shen, Li

    2017-01-01

    Sisal fibre can potentially replace glass fibre in natural fibre composites. This study focuses on the environmental performance of sisal fibre production by quantifying the greenhouse gas (GHG) emissions and energy use of producing sisal fibre in Tanzania and Brazil using life cycle assessment

  3. Dust in protoplanetary disks: observations*

    Directory of Open Access Journals (Sweden)

    Waters L.B.F.M.

    2015-01-01

    Full Text Available Solid particles, usually referred to as dust, are a crucial component of interstellar matter and of planet forming disks surrounding young stars. Despite the relatively small mass fraction of ≈1% (in the solar neighborhood of our galaxy; this number may differ substantially in other galaxies that interstellar grains represent of the total mass budget of interstellar matter, dust grains play an important role in the physics and chemistry of interstellar matter. This is because of the opacity dust grains at short (optical, UV wavelengths, and the surface they provide for chemical reactions. In addition, dust grains play a pivotal role in the planet formation process: in the core accretion model of planet formation, the growth of dust grains from the microscopic size range to large, cm-sized or larger grains is the first step in planet formation. Not only the grain size distribution is affected by planet formation. Chemical and physical processes alter the structure and chemical composition of dust grains as they enter the protoplanetary disk and move closer to the forming star. Therefore, a lot can be learned about the way stars and planets are formed by observations of dust in protoplanetary disks. Ideally, one would like to measure the dust mass, the grain size distribution, grain structure (porosity, fluffiness, the chemical composition, and all of these as a function of position in the disk. Fortunately, several observational diagnostics are available to derive constrains on these quantities. In combination with rapidly increasing quality of the data (spatial and spectral resolution, a lot of progress has been made in our understanding of dust evolution in protoplanetary disks. An excellent review of dust evolution in protoplanetary disks can be found in Testi et al. (2014.

  4. Oxidation of lignin in hemp fibres by laccase: effects on mechanical properties of hemp fibres and unidirectional fibre/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Baum, Andreas; Odermatt, Jürgen

    2017-01-01

    Laccase activity catalyzes oxidation and polymerization of phenols. The effect of laccase treatment on the mechanical properties of hemp fibres and hemp fibre/epoxy composites was examined. Laccase treatment on top of 0.5% EDTA + 0.2% endo-polygalacturonase (EPG) treatments increased the mechanical...

  5. Fibred Coalgebraic Logic and Quantum Protocols

    Directory of Open Access Journals (Sweden)

    Daniel Marsden

    2014-12-01

    Full Text Available Motivated by applications in modelling quantum systems using coalgebraic techniques, we introduce a fibred coalgebraic logic. Our approach extends the conventional predicate lifting semantics with additional modalities relating conditions on different fibres. As this fibred setting will typically involve multiple signature functors, the logic incorporates a calculus of modalities enabling the construction of new modalities using various composition operations. We extend the semantics of coalgebraic logic to this setting, and prove that this extension respects behavioural equivalence. We show how properties of the semantics of modalities are preserved under composition operations, and then apply the calculational aspect of our logic to produce an expressive set of modalities for reasoning about quantum systems, building these modalities up from simpler components. We then demonstrate how these modalities can describe some standard quantum protocols. The novel features of our logic are shown to allow for a uniform description of unitary evolution, and support local reasoning such as "Alice's qubit satisfies condition" as is common when discussing quantum protocols.

  6. D fibre antenna for microcellular communications

    CERN Document Server

    Bhatti, A A

    2003-01-01

    Over the years, optical fibre sensors have been developed for many application areas. With the recent growth of microcellular communication systems this area has great economic potential. Therefore with this in mind one promising application for a new optical fibre sensor system is in the detection of Radio Frequency/Electric Fields (RF/EF). By constructing such a sensor from totally dielectric materials, it could be used as an antenna for receiving radio frequency transmissions without distorting or disturbing the field lines since there are no metallic components to reflect or transmit radio frequency energy. One of the key issues in the realisation of Radio-over-Fibre (RoF) architecture is the development of an effective means of generating and transmitting the radio subcarrier. The simplest method for the optical generation of radio signals, for transmission through an optical network is to directly modulate the light source with the received RF signal. Direct modulation of the laser can lead to a number ...

  7. A fibre optic dosimeter customised for brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Suchowerska, N. [Department of Radiation Oncology, Royal Prince Alfred Hospital, Camperdown, NSW 2050 (Australia); School of Physics, University of Sydney, NSW 2006 (Australia)], E-mail: Natalka@email.cs.nsw.gov.au; Lambert, J.; Nakano, T. [Department of Radiation Oncology, Royal Prince Alfred Hospital, Camperdown, NSW 2050 (Australia); School of Physics, University of Sydney, NSW 2006 (Australia); Law, S. [School of Physics, University of Sydney, NSW 2006 (Australia); Optical Fibre Technology Centre, University of Sydney, 206 National Innovation Centre, Australian Technology Park, Eveleigh, NSW 1430 (Australia); Elsey, J. [Bandwidth Foundry Pty Ltd, Australian Technology Park, NSW, 1430 (Australia); McKenzie, D.R. [School of Physics, University of Sydney, NSW 2006 (Australia)

    2007-04-15

    In-vivo dosimetry for brachytherapy cancer treatment requires a small dosimeter with a real time readout capability that can be inserted into the patient to determine the dose to critical organs. Fibre optic scintillation dosimeters, consisting of a plastic scintillator coupled to an optical fibre, are a promising dosimeter for this application. We have implemented specific design features to optimise the performance of the dosimeter for specific in-vivo dosimetry during brachytherapy. Two sizes of the BrachyFOD{sup TM} scintillation dosimeter have been developed, with external diameters of approximately 2 and 1 mm. We have determined their important dosimetric characteristics (depth dose relation, angular dependence, energy dependence). We have shown that the background signal created by Cerenkov and fibre fluorescence does not significantly affect the performance in most clinical geometries. The dosimeter design enables readout at less than 0.5 s intervals. The clinical demands of real time in-vivo brachytherapy dosimetry can uniquely be satisfied by the BrachyFOD{sup TM}.

  8. A Fibre Optic Sensor Of Physiological Parameters

    Science.gov (United States)

    Legendre, J. P.; Forester, G. V.

    1986-11-01

    This paper presents an ultraminiature fibre optic probe capable of physiological monitoring in situ. The system has been described previously where a fibre optic reflectometer was configured as a temperature sensor and as a refractometer. For the present experiments a bare fibre tip was used as sensing element. We show that we have been able to monitor cyclic physiological parameters such as heart and respiratory rates in various animal preparations. The probe has been used to obtain signals from the oesophagus, the lower gastro-intestinal tract, the abdominal cavity and from blood vessels (arteries and veins). The probe has also measured phasic activity coincident with mechanical activity of isolated heart muscle. The small physical size of the sensor (125 µm diameter), its flexibility and the fact that it is biologically inert are all very important characteristics for medical and biological considerations. Most recently, the probe has been used to monitor cardiac and respiratory rates while obtaining NMR spectra assessing metabolic activity. This was possible only because the probe is magnetically transparent.

  9. Bundled capillary electrophoresis using microstructured fibres.

    Science.gov (United States)

    Rogers, Benjamin; Gibson, Graham T T; Oleschuk, Richard D

    2011-01-01

    Joule heating, arising from the electric current passing through the capillary, causes many undesired effects in CE that ultimately result in band broadening. The use of narrow-bore capillaries helps to solve this problem as smaller cross-sectional area results in decreased Joule heating and the rate of heat dissipation is increased by the larger surface-to-volume ratio. Issues arising from such small capillaries, such as poor detection sensitivity, low loading capacity and high flow-induced backpressure (complicating capillary loading) can be avoided by using a bundle of small capillaries operating simultaneously that share buffer reservoirs. Microstructured fibres, originally designed as waveguides in the telecommunication industry, are essentially a bundle of parallel ∼5 μm id channels that extend the length of a fibre having otherwise similar dimensions to conventional CE capillaries. This work presents the use of microstructured fibres for CZE, taking advantage of their relatively high surface-to-volume ratio and the small individual size of each channel to effect highly efficient separations, particularly for dye-labelled peptides.

  10. Applications and Properties of Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    Amit Rai1 ,

    2014-05-01

    Full Text Available In conventional concrete, micro-cracks develop before structure is loaded because of drying shrinkage and other causes of volume change. When the structure is loaded, the micro cracks open up and propagate because of development of such micro-cracks, results in inelastic deformation in concrete. Fibre reinforced concrete (FRC is cementing concrete reinforced mixture with more or less randomly distributed small fibres. In the FRC, a numbers of small fibres are dispersed and distributed randomly in the concrete at the time of mixing, and thus improve concrete properties in all directions. The fibers help to transfer load to the internal micro cracks. FRC is cement based composite material that has been developed in recent years. It has been successfully used in construction with its excellent flexural-tensile strength, resistance to spitting, impact resistance and excellent permeability and frost resistance. It is an effective way to increase toughness, shock resistance and resistance to plastic shrinkage cracking of the mortar. These fibers have many benefits. Steel fibers can improve the structural strength to reduce in the heavy steel reinforcement requirement. Freeze thaw resistance of the concrete is improved. Durability of the concrete is improved to reduce in the crack widths. Polypropylene and Nylon fibers are used to improve the impact resistance. Many developments have been made in the fiber reinforced concrete.

  11. Chronological ageing of human hair keratin fibres.

    Science.gov (United States)

    Thibaut, S; de Becker, E; Bernard, B A; Huart, M; Fiat, F; Baghdadli, N; Luengo, G S; Leroy, F; Angevin, P; Kermoal, A M; Muller, S; Peron, M; Provot, G; Kravtchenko, S; Saint-Léger, D; Desbois, G; Gauchet, L; Nowbuth, K; Galliano, A; Kempf, J Y; Silberzan, I

    2010-12-01

    Examination of very long hair (length > 2.4 m) using a large range of evaluation methods including physical, chemical, biochemical and microscopic techniques has enabled to attain a detailed understanding of natural ageing of human hair keratin fibres. Scrutinizing hair that has undergone little or no oxidative aggression--because of the absence of action of chemical agents such as bleaching or dyeing--from the root to the tip shows the deterioration process, which gradually takes place from the outside to the inside of the hair shaft: first, a progressive abrasion of the cuticle, whilst the cortex structure remains unaltered, is evidenced along a length of roughly 1 m onwards together with constant shine, hydrophobicity and friction characteristics. Further along the fibre, a significant damage to cuticle scales occurs, which correlates well with ceramides and 18-Methyl Eicosanoic Acid (18-MEA) decline, and progressive decrease in keratin-associated protein content. Most physical descriptors of mechanical and optical properties decay significantly. This detailed description of natural ageing of human hair fibres by a fine analysis of hair components and physical parameters in relationship with cosmetic characteristics provides a time-dependent 'damage scale' of human hair, which may help in designing new targeted hair care formulations.

  12. Fibre optic portable rail vehicle detector

    Science.gov (United States)

    Kepak, Stanislav; Cubik, Jakub; Zavodny, Petr; Hejduk, Stanislav; Nedoma, Jan; Davidson, Alan; Vasinek, Vladimir

    2016-12-01

    During track maintenance operations, the early detection of oncoming rail vehicles is critical for the safety of maintenance personnel. In addition, the detection system should be simple to install at the trackside by minimally qualified personnel. Fibre optic based sensor systems have the inherent advantages of being passive, unaffected by radio frequency interference (RFI) and suffering very low signal attenuation. Such a system therefore represents a good alternative to conventional approaches such as ultrasonic based sensor systems. The proposed system consists of one or more passive fibre trackside sensors and an x86 processing unit located at the work site. The solid fibre connection between sensors and processing unit eliminates the risk of RFI. In addition, the detection system sensors are easy to install with no requirement for electrical power at the sensor site. The system was tested on a tram line in Ostrava with the results obtained indicating the successful detection of all the trams in the monitoring windows using a single sensor. However, the platform allows flexibility in configuring multiple sensors where required by system users.

  13. Unidirectional Cordenka Fibre-Reinforced Furan Resin Full Biocomposite: Properties and Influence of High Fibre Mass Fraction

    Directory of Open Access Journals (Sweden)

    Talent Malaba

    2015-01-01

    Full Text Available A full biocomposite was fabricated from Cordenka CR fibre and furan resin. High fibre mass fractions (FMF were achieved by pressing the CR fibres into unidirectional sheets prior to incorporation into the resin. Results of testing indicated that the tensile properties of the biocomposite were improved by the initial increase of FMF from 51 to 64%, with a subsequent increase of FMF to 75% resulting in a deterioration of those properties. Examination of the tensile fracture surfaces with a scanning electron microscope (SEM revealed moderate deterioration in fibre-matrix adhesion after the initial increase of FMF. Further increase of the FMF to 75% was shown by SEM to result in worse fibre-matrix adhesion. On the other hand, the flexural, interlaminar-shear, and dynamic mechanical properties were adversely affected by the increase in fibre-mass fraction from 51 through 75%. These effects were mainly attributed to reduced fibre wetting that resulted in weakened fibre-matrix interfacial bonding and subsequent poor stress exchange at the fibre-matrix interface. Observations made with a digital microscope revealed normal crack behaviour in the laminated composite, and the shear fracture modes were I and II. This biocomposite has mechanical properties comparable to those of flax and glass fibre-reinforced furan resin biocomposites.

  14. Influence of an Optimized Fibre Coating on Interfacial and Mechanical Properties of Glass Fibre/Polypropylene Composites

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The influence of pretreatment of fibre on interfacial and mechanical properties of glass fibre/polypropylene composites was investigated. Firstly, the glass fibres were coated with the blends of m-IPP (maleic anhydride grafting isotatic polypropylene) and m-APP (maleic anhydride grafting amorphous polypropylene) in different ratios.Secondly, the interfacial reaction of the coated composites was analysed by FTIR, which shows that the interfacial chemical reaction between m-IPP/m-APP in the fibre coating and the fibre surface-bound coupling agent is in existence.Thirdly, the microstructure of the coated composites was studied by SEM. The results indicate that the coating treatment is effective on improving interfacial adhesion of the fibre-matrix and the right amount of m-APP added to the coat impels the plastic deformation surrounding the point of cracks, which makes cracks turn to region and prevents from further interface debonding. Lastly, the mechanical properties were evaluated by measurement of the flexural strength and impact strength of the composites. It was found that the flexural strength and impact strength of the composites with coating fibre are higher than those of uncoating fibre composite. The results of these investigations draw the conclusion that the pretreatment of fibre with m-IPP/m-APP blends can form an optimize interlayer between the fibre and the PP matrix, which improves both the strength and toughness of the composites.

  15. Dust-acoustic waves and stability in the permeating dust plasma: II. Power-law distributions

    CERN Document Server

    Gong, Jingyu; Du, Jiulin

    2012-01-01

    The dust-acoustic waves and their stability driven by a flowing dust plasma when it cross through a static (target) dust plasma (the so-called permeating dust plasma) are investigated when the components of the dust plasma obey the power-law q-distributions in nonextensive statistics. The frequency, the growth rate and the stability condition of the dust-acoustic waves are derived under this physical situation, which express the effects of the nonextensivity as well as the flowing dust plasma velocity on the dust-acoustic waves in this dust plasma. The numerical results illustrate some new characteristics of the dust-acoustic waves, which are different from those in the permeating dust plasma when the plasma components are the Maxwellian distribution. In addition, we show that the flowing dust plasma velocity has a significant effect on the dust-acoustic waves in the permeating dust plasma with the power-law q-distribution.

  16. Increased mortality in COPD among construction workers exposed to inorganic dust.

    Science.gov (United States)

    Bergdahl, I A; Torén, K; Eriksson, K; Hedlund, U; Nilsson, T; Flodin, R; Järvholm, B

    2004-03-01

    The aim of this study was to find out if occupational exposure to dust, fumes or gases, especially among never-smokers, increased the mortality from chronic obstructive pulmonary disease (COPD). A cohort of 317,629 Swedish male construction workers was followed from 1971 to 1999. Exposure to inorganic dust (asbestos, man-made mineral fibres, dust from cement, concrete and quartz), gases and irritants (epoxy resins, isocyanates and organic solvents), fumes (asphalt fumes, diesel exhaust and metal fumes), and wood dust was based on a job-exposure matrix. An internal control group with "unexposed" construction workers was used, and the analyses were adjusted for age and smoking. When all subjects were analysed, there was an increased mortality from COPD among those with any airborne exposure (relative risk 1.12 (95% confidence interval (CI) 1.03-1.22)). In a Poisson regression model, including smoking, age and the major exposure groups, exposure to inorganic dust was associated with an increased risk (hazard ratio (HR) 1.10 (95% CI 1.06-1.14)), especially among never-smokers (HR 2.30 (95% CI 1.07-4.96)). The fraction of COPD among the exposed attributable to any airborne exposure was estimated as 10.7% overall and 52.6% among never-smokers. In conclusion, occupational exposure among construction workers increases mortality due to chronic obstructive pulmonary disease, even among never-smokers.

  17. Skinned fibres produce the same power and force as intact fibre bundles from muscle of wild rabbits.

    Science.gov (United States)

    Curtin, Nancy A; Diack, Rebecca A; West, Timothy G; Wilson, Alan M; Woledge, Roger C

    2015-09-01

    Skinned fibres have advantages for comparing the muscle properties of different animal species because they can be prepared from a needle biopsy taken under field conditions. However, it is not clear how well the contractile properties of skinned fibres reflect the properties of the muscle fibres in vivo. Here, we compare the mechanical performance of intact fibre bundles and skinned fibres from muscle of the same animals. This is the first such direct comparison. Maximum power and isometric force were measured at 25 °C using peroneus longus (PL) and extensor digiti-V (ED-V) muscles from wild rabbits (Oryctolagus cuniculus). More than 90% of the fibres in these muscles are fast-twitch, type 2 fibres. Maximum power was measured in force-clamp experiments. We show that maximum power per volume was the same in intact (121.3 ± 16.1 W l(-1), mean ± s.e.m.; N=16) and skinned (122.6 ± 4.6 W l(-1); N=141) fibres. Maximum relative power (power/F(IM) Lo, where F(IM) is maximum isometric force and Lo is standard fibre length) was also similar in intact (0.645 ± 0.037; N=16) and skinned (0.589 ± 0.019; N=141) fibres. Relative power is independent of volume and thus not subject to errors in measurement of volume. Finally, maximum isometric force per cross-sectional area was also found to be the same for intact and skinned fibres (181.9 kPa ± 19.1; N=16; 207.8 kPa ± 4.8; N=141, respectively). These results contrast with previous measurements of performance at lower temperatures where skinned fibres produce much less power than intact fibres from both mammals and non-mammalian species. © 2015. Published by The Company of Biologists Ltd.

  18. E ring dust sources: Implications from Cassini's dust measurements

    Science.gov (United States)

    Spahn, Frank; Albers, Nicole; Hörning, Marcel; Kempf, Sascha; Krivov, Alexander V.; Makuch, Martin; Schmidt, Jürgen; Seiß, Martin; Miodrag Sremčević

    2006-08-01

    The Enceladus flybys of the Cassini spacecraft are changing our understanding of the origin and sustainment of Saturn's E ring. Surprisingly, beyond the widely accepted dust production caused by micrometeoroid impacts onto the atmosphereless satellites (the impactor-ejecta process), geophysical activities have been detected at the south pole of Enceladus, providing an additional, efficient dust source. The dust detector data obtained during the flyby E11 are used to identify the amount of dust produced in the impactor-ejecta process and to improve related modeling [Spahn, F., Schmidt, J., Albers, N., Hörning, M., Makuch, M., Seiß, M., Kempf, S., Srama, R., Dikarev, V.V., Helfert, S., Moragas-Klostermeyer, G., Krivov, A.V., Sremčević, M., Tuzzolino, A., Economou, T., Grün, E., 2006. Cassini dust measurements at Enceladus: implications for Saturn's E ring. Science, in press]. With this, we estimate the impact-generated dust contributions of the other E ring satellites and find significant differences in the dust ejection efficiency by two projectile families - the E ring particles (ERPs) and the interplanetary dust particles (IDPs). Together with the Enceladus south-pole source, the ERP impacts play a crucial role in the inner region, whereas the IDP impacts dominate the particle production in the outer E ring, possibly accounting for its large radial extent. Our results can be verified in future Cassini flybys of the E ring satellites. In this way poorly known parameters of the dust particle production in hypervelocity impacts can be constrained by comparison of the data and theory.

  19. The health effects of man-made mineral fibres originating from an air-handling system; Ilmanvaihtojaerjestelmaen mineraalivillakuitujen terveysvaikutukset

    Energy Technology Data Exchange (ETDEWEB)

    Tuomainen, M.; Bjoerkroth, M.; Kaemppi, R.; Mussalo-Rauhamaa, H.; Salo, S.P.; Saentti, J.; Tuomi, T.; Voutilainen, R.; Seppaenen, O.

    2003-07-01

    The aim of the research project was to confirm the results obtained in a pilot project according to which the symptoms of the hospital personnel were caused by man-made mineral fibres originating from the air-handling system. The pilot project showed that the prevalence of symptoms decreased after the sound attenuators in the air handling system were treated with a fibre-binding agent, and the wards cleaned thoroughly. The research project ''The health effects of man-made mineral fibres originating from an air-handling system'' was launched and carried out within a tight schedule. HUS- kiinteistoet Oy, the building management company responsible for maintaining the hospital buildings in the Helsinki area, selected two hospitals for the project. The air distribution conduit of the research hospital was large, and to deaden sound its interior surface was lined with a man-made mineral fibre material covered with perforated steel plates. The dust in the air distribution system contained man-made mineral fibres (MMMF) but the concentrations on room surfaces were low. Two wards in both the research and reference hospitals were selected for the study. Their personnel answered a baseline questionnaire in April 2002. When it turned out that the reference hospital was undergoing exterior facade renovations, the personnel of the reference building was excluded from further investigations. The personnel working in the wards under study in the research hospital were invited to take part in nasal lavage in June 2002. The participants answered a questionnaire inquiring into the work environment and work-related symptoms during June. Improvements to the air-handling system were carried out in July. The sound attenuation material was coated and the ventilation ducts cleaned. The quality of the improvements was controlled by assessment of fibre concentrations on duct and room surfaces. Post-intervention lavage of the nasal mucosa was carried out in December 2002

  20. Advances in infrared and imaging fibres for astronomical instrumentation

    CERN Document Server

    Haynes, R; Marcel, J; Jovanovic, N; Haynes, Roger; Namara, Pam Mc; Marcel, Jackie; Jovanovic, Nemanja

    2006-01-01

    Optical fibres have already played a huge part in ground based astronomical instrumentation, however, with the revolution in photonics currently taking place new fibre technologies and integrated optical devices are likely to have a profound impact on the way we manipulate light in the future. The Anglo-Australian Observatory, along with partners at the Optical Fibre Technology Centre of the University of Sydney, is investigating some of the developing technologies as part of our Astrophotonics programme. In this paper we discuss the advances that have been made with infrared transmitting fibre, both conventional and microstructured, in particular those based on flouride glasses. Flouride glasses have a particularly wide transparent region from the UV through to around 7um, whereas silica fibres, commonly used in astronomy, only transmit out to about 2um. We discuss the impact of advances in fibre manufacture that have greatly improved the optical, chemical resistance and physical properties of the flouride f...

  1. Erbium-doped nanoparticles in silica-based optical fibres

    CERN Document Server

    Blanc, Wilfried; Dussardier, Bernard; 10.1504/IJNT.2012.045350

    2012-01-01

    Developing of new rare-earth (RE)-doped optical fibres for power amplifiers and lasers requires continuous improvements in the fibre spectroscopic properties (like shape and width of the gain curve, optical quantum efficiency, resistance to spectral hole burning and photodarkening...). Silica glass as a host material for fibres has proved to be very attractive. However, some potential applications of RE-doped fibres suffer from limitations in terms of spectroscopic properties resulting from clustering or inappropriate local environment when doped into silica. To this aim, we present a new route to modify some spectroscopic properties of RE ions in silica-based fibres based on the incorporation of erbium ions in amorphous dielectric nanoparticles, grown in-situ in fibre preforms. By adding alkaline earth elements, in low concentration into silica, one can obtain a glass with an immiscibility gap. Then, phase separation occurs under an appropriate heat treatment. We investigated the role of three alkaline-earth...

  2. Statistical data for the tensile properties of natural fibre composites

    Directory of Open Access Journals (Sweden)

    J.P. Torres

    2017-06-01

    Full Text Available This article features a large statistical database on the tensile properties of natural fibre reinforced composite laminates. The data presented here corresponds to a comprehensive experimental testing program of several composite systems including: different material constituents (epoxy and vinyl ester resins; flax, jute and carbon fibres, different fibre configurations (short-fibre mats, unidirectional, and plain, twill and satin woven fabrics and different fibre orientations (0°, 90°, and [0,90] angle plies. For each material, ~50 specimens were tested under uniaxial tensile loading. Here, we provide the complete set of stress–strain curves together with the statistical distributions of their calculated elastic modulus, strength and failure strain. The data is also provided as support material for the research article: “The mechanical properties of natural fibre composite laminates: A statistical study” [1].

  3. Scanners for the quality contol of scintillating plastic fibres

    CERN Document Server

    Rodigues, Ana Barbara; Garnier, Francois; Giudici, Pierre-Ange; Greim, Roman; Hebler, Philip; Joram, Christian; Kirn, Thomas; Pierschel, Gerhard; Schateikis, Tobias; Stevens, Holger; Bachlechner, Andreas; Deckenhoff, Mirco; Karpinski, Waclaw; Kruse, Florian; Schultz Von Dratzig, Arndt; Schwering, Georg; Swientek, Krzysztof Piotr; Wlochal, Michael

    2015-01-01

    The use of scintillating plastic fibres in the SciFi tracker requires rigorous quality control. The fibre diameter and in particular local variations in form of bumps and necks have an impact on the regularity of the winding pattern and hence the spatial resolution. Defects in the fibre cladding lead to light losses and inter-fibre cross talk. Machines have been developed which allow scanning at high throughput of the fibre diameter and the integrity of the cladding. We describe the design principles and implementations of these machines and illustrate their performance. While these machines allow to identify and quantify performance issues of the prototype fibres, they will also play a major role during the series production of the SciFi tracker. If needed, the capacity of the machines allows scanning of the full production volume.

  4. A new method of making metal matrix fibre reinforced materials

    Energy Technology Data Exchange (ETDEWEB)

    Schaupp, J. (Inst. fuer Werkzeugmaschinen und Betriebstechnik, Univ. Karlsruhe (Germany)); Pruemmer, R. (Inst. fuer Werkzeugmaschinen und Betriebstechnik, Univ. Karlsruhe (Germany) Ernst-Mach-Inst., Freiburg (Germany))

    1993-11-01

    MMC (metal matrix composites) made of ceramic fibres and metal matrix are suitable for high strength and high temperature applications. New types of ceramic fibres usually are incorporated into a metal matrix by means of liquid infiltration or by hot pressing techniques. The disadvantage of these methods is the chemical reaction sometimes occurring between fibre and matrix, resulting in an interlayer which is degrading the mechanical properties of the MMC. A new method is described starting with an arrangement of metal powder or metal foils with ceramic fibres. Dynamic pressures, released by detonation of proper explosives, are used for consolidation. At very high strain rates during plastic deformation of the powder or metal foils hydrodynamic flow of the matrix around the ceramic fibres allows a complete consolidation and to prevent cracking. Fibres made of SiC are embedded into a metal matrix of aluminum. (orig.).

  5. Effects of chemical treatments on hemp fibre structure

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, M.M., E-mail: kabirm@usq.edu.au [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Wang, H. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Lau, K.T. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia); Department of Mechanical Engineering, The Hong Kong Polytechnic University, Kowloon, Hong Kong Special Administrative Region (Hong Kong); Cardona, F. [Centre of Excellence in Engineered Fibre Composite (CEEFC), Faculty of Engineering and Surveying, University of Southern Queensland, Toowoomba, Queensland 4350 (Australia)

    2013-07-01

    In this study, hemp fibres were treated with alkali, acetyl and silane chemicals. Fibre constituents such as cellulose, hemicellulose and lignin constituents were separated from treated fibres. The chemical and thermal influences of these constituents on the treated fibres were examined by using scanning electron microscope (SEM), fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Experimental results revealed that, hemicellulose was degraded faster than that of cellulose and lignin. Cellulose exhibited better thermal stability and lignin was degraded in a wide range of temperatures. The hydrophilic nature of the fibres was predominantly caused by the presence of hemicellulose and then lignin constituents. Hemicellulose and lignin were mostly removed by the alkalisation with higher concentrations of NaOH, followed by acetylation. Silane treatment could not remove the hemicellulose and lignin, rather this treatment facilitated coupling with the fibre constituents.

  6. Flat Ge-doped optical fibres for food irradiation dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Noor, N. Mohd; Jusoh, M. A. [Department of Imaging, Faculty of Medicine and Health Sciences, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Razis, A. F. Abdull [Food Safety Research Centre, Faculty of Food Science and Technology, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Laboratory of UPM-MAKNA Cancer Research, Institute of Bioscience, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Alawiah, A. [Faculty of Engineering and Technology, Multimedia University, 75450 Malacca (Malaysia); Bradley, D. A. [Department of Physics, University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom); Department of Physics, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2015-04-24

    Exposing food to radiation can improve hygiene quality, germination control, retard sprouting, and enhance physical attributes of the food product. To provide for food safety, radiation dosimetry in irradiated food is required. Herein, fabricated germanium doped (Ge-doped) optical fibres have been used. The fibres have been irradiated using a gamma source irradiator, doses in the range 1 kGy to 10 kGy being delivered. Using Ge-doped optical fibres of variable size, type and dopant concentration, study has been made of linearity, reproducibility, and fading. The thermoluminescence (TL) yield of the fibres were obtained and compared. The fibres exhibit a linear dose response over the investigated range of doses, with mean reproducibility to within 2.69 % to 8.77 %, exceeding the dose range of all commercial dosimeters used in evaluating high doses for the food irradiation industry. TL fading of the Ge-doped flat fibres has been found to be < 13%.

  7. Chemical stability of prints made on hemp fibre based papers

    Directory of Open Access Journals (Sweden)

    Ivana Plazonić

    2016-11-01

    Full Text Available For paper industry and consequently graphic industry it is very important that fibres used in paper production provide high quality and printability of the paper. In pulp and paper industry fibres of cellulose pulp derived still predominantly from wood, but in the last few years the consumption of non-wood raw materials for that purpose has grown. This work presents research on the chemical stability of printed hemp fibre based papers to water, alcohol and alkali. Evaluation of chemical degradation on prints was determined through the spectrophotometric measurements. Deviations in colour of prints have shown that highest chemical stability provides prints made on industrially paper formed from mixture of hemp and post-consumer fibres with high share of inorganic components. Further, bleached hemp fibres in handmade 100 % hemp fibre based paper give prints with the lowest chemical stability.

  8. A Continuously Tunable Erbium-Doped Fibre Laser Using Tunable Fibre Bragg Gratings and Optical Circulator

    Science.gov (United States)

    Liu, Peng; Yan, Feng-Ping; Li, Jian; Wang, Lin; Ning, Ti-Gang; Gong, Tao-Rong; Jian, Shui-Sheng

    2008-12-01

    A continuously tunable erbium-doped fibre laser (TEDFL) based on tunable fibre Bragger grating (TFBG) and a three-port optical circulator (OC) is proposed and demonstrated. The OC acts as a 100%-reflective mirror. A strain-induced uniform fibre Bragger grating (FBG) which functions as a partial-reflecting mirror is implemented in the linear cavity. By applying axial strain onto the TFBG, a continuously tunable lasing output can be realized. The wavelength tuning range covers approximately 7.00nm in C band (from 1543.6161 to 1550.3307nm). The side mode suppression ratio (SMSR) is better than 50 dB, and the 3 dB bandwidth of the laser is less than 0.01 nm. Moreover, an array waveguide grating (AWG) is inserted into the cavity for wavelength preselecting, and a 50 km transmission experiment was performed using our TEDFL at a 10Gb/s modulation rate.

  9. Guidance in Kagome-like photonic crystal fibres II: perturbation theory for a realistic fibre structure.

    Science.gov (United States)

    Chen, Lei; Bird, David M

    2011-03-28

    A perturbation theory is developed that treats a localised mode embedded within a continuum of states. The method is applied to a model rectangular hollow-core photonic crystal fibre structure, where the basic modes are derived from an ideal, scalar model and the perturbation terms include vector effects and structural difference between the ideal and realistic structures. An expression for the attenuation of the fundamental mode due to interactions with cladding modes is derived, and results are presented for a rectangular photonic crystal fibre structure. Attenuations calculated in this way are in good agreement with numerical simulations. The origin of the guidance in our model structure is explained through this quantitative analysis. Further perspectives are obtained through investigating the influence of fibre parameters on the attenuation.

  10. Blue Up-Conversion Fibre Laser Pumped by a 1120-nm Raman Fibre Laser

    Institute of Scientific and Technical Information of China (English)

    QIN Guan-Shi; HUANG Sheng-Hong; FENG Yan; SHIRAKAWA A.; MUSHA M.; UEDA Ken-ichi

    2005-01-01

    @@ A Tm3+-doped ZrF4-BaF2-LaF3-AlF3-NaF (ZBLAN) fibre up-conversion laser pumped by a 1120-nm Raman fibre laser is demonstrated with blue output power levels up to 116mW. For the output mirror with 80% reflectivity, the slope efficiency is about 15%, the optical-to-optical conversion efficiency is 11%, and the maximum un-saturated output power is 116mW. For 60% reflectivity, the slope efficiency is about 18% and the opticalto-optical conversion efficiency is 12%, whilst the maximum saturated output power is about 80mW due to the existence of photo-degradation effect in Tm3+ doped ZBLAN glass fibre.

  11. Five Wavelength DFB Fibre Laser Source for WDM Systems

    DEFF Research Database (Denmark)

    Hübner, Jörg; Varming, Poul; Kristensen, Martin

    1997-01-01

    Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of <15 kHz and a sidemode suppression better than 61 dB are presented. The stability of the lasers is verified by a 10 Gbit/s transmission experiment. Five DFB fibre lasers are cascaded and pumped by a single semicondu......Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of pumped by a single...

  12. Optical inclinometer based on fibre-taper-modal Michelson interferometer

    Science.gov (United States)

    Amaral, L. M. N.; Frazão, O.; Santos, J. L.; Lobo Ribeiro, A. B.

    2010-09-01

    An inclinometer sensor based on optical fibre-taper-modal Michelson interferometer is demonstrated. The magnitude of the tilt (bending angle of the fibre taper interferometer) is obtained by passive interferometric interrogation based on the generation of two quadrature phase-shifted signals from two fibre Bragg gratings. Optical phase-to-rotation sensitivity of 1.13 rad/degree with a 14 mrad/√Hz resolution is achieved.

  13. The hygroscopic behavior of plant fibres: a review

    Science.gov (United States)

    Célino, Amandine; Freour, Sylvain; Jacquemin, Frederic; Casari, Pascal

    2013-12-01

    Environmental concern has resulted in a renewed interest in bio-based materials. Among them, plant fibres are perceived as an environmentally friendly substitute to glass fibres for the reinforcement of composites, particularly in automotive engineering. Due to their wide availability, low cost, low density, high-specific mechanical properties and eco-friendly image, they are increasingly being employed as reinforcements in polymer matrix composites. Indeed, their complex microstructure as a composite material makes plant fibre a really interesting and challenging subject to study. Research subjects about such fibres are abundant because there are always some issues to prevent their use at large scale (poor adhesion, variability, low thermal resistance, hydrophilic behavior). The choice of natural fibres rather than glass fibres as filler yields a change of the final properties of the composite. One of the most relevant differences between the two kinds of fibre is their response to humidity. Actually, glass fibres are considered as hydrophobic whereas plant fibres have a pronounced hydrophilic behavior. Composite materials are often submitted to variable climatic conditions during their lifetime, including unsteady hygroscopic conditions. However, in humid conditions, strong hydrophilic behaviour of such reinforcing fibres leads to high level of moisture absorption in wet environments. This results in the structural modification of the fibres and an evolution of their mechanical properties together with the composites in which they are fitted in. Thereby, the understanding of these moisture absorption mechanisms as well as the influence of water on the final properties of these fibres and their composites is of great interest to get a better control of such new biomaterials. This is the topic of this review paper.

  14. Thermal dependence of passive electrical properties of lizard muscle fibres.

    Science.gov (United States)

    Adams, B A

    1987-11-01

    1. The thermal dependence of passive electrical properties was determined for twitch fibres from the white region of the iliofibularis (IF) muscle of Anolis cristatellus (15-35 degrees C) and Sceloporus occidentalis (15-40 degrees C), and for twitch fibres from the white (15-45 degrees C) and red (15-40 degrees C) regions of the IF of Dipsosaurus dorsalis. These species differ in thermal ecology, with Anolis being the least thermophilic and Dipsosaurus the most thermophilic. 2. Iliofibularis fibres from the three species reacted similarly to changing temperature. As temperature was increased, input resistance (Rin) decreased (average R10 = 0.7), length constant (L) decreased (average R10 = 0.9), time constant (tau) decreased (average R10 = 0.8), sarcoplasmic resistivity (Rs) decreased (average R10 = 0.8) and apparent membrane resistance (Rm) decreased (average R10 = 0.7). In contrast, apparent membrane capacitance (Cm) increased with increasing temperature (average R10 = 1.3). 3. Rin, L, tau and apparent Rm were lowest in fibres from Anolis (the least thermophilic species) and highest in fibres from Dipsosaurus (the most thermophilic species). Anolis had the largest and Dipsosaurus the smallest diameter fibres (126 and 57 micron, respectively). Apparent Cm was highest in fibres from Sceloporus, which had fibres of intermediate diameter (101 micron). Rs did not differ significantly among species. 4. The effect of temperature on the passive electrical properties of these lizard fibres was similar to that reported for muscle fibres from other ectothermic animals (crustaceans, insects, fish and amphibians) but qualitatively different from that reported for some mammalian (cat tenuissimus, goat intercostal) fibres. The changes that occur in the passive electrical properties render the fibres less excitable as temperature increases.

  15. The hygroscopic behavior of plant fibres: a review

    Directory of Open Access Journals (Sweden)

    Amandine eCélino

    2014-01-01

    Full Text Available Environmental concern has resulted in a renewed interest in bio-based materials. Among them, plant fibres are perceived as an environmentally friendly substitute to glass fibres for the reinforcement of composites, particularly in automotive engineering. Due to their wide availability, low cost, low density, high-specific mechanical properties and eco-friendly image, they are increasingly being employed as reinforcements in polymer matrix composites. Indeed, their complex microstructure as a composite material makes plant fibre a really interesting and challenging subject to study. Research subjects about such fibres are abundant because there are always some issues to prevent their use at large scale (poor adhesion, variability, low thermal resistance, hydrophilic behavior. The choice of natural fibres rather than glass fibres as filler yields a change of the final properties of the composite. One of the most relevant differences between the two kinds of fibre is their response to humidity. Actually, glass fibres are considered as hydrophobic whereas plant fibres have a pronounced hydrophilic behavior. Composite materials are often submitted to variable climatic conditions during their lifetime, including unsteady hygroscopic conditions. However, in humid conditions, strong hydrophilic behaviour of such reinforcing fibres leads to high level of moisture absorption in wet environments. This results in the structural modification of the fibres and an evolution of their mechanical properties together with the composites in which they are fitted in. Thereby, the understanding of these moisture absorption mechanisms as well as the influence of water on the final properties of these fibres and their composites is of great interest to get a better control of such new biomaterials. This is the topic of this review paper.

  16. Five Wavelength DFB Fibre Laser Source for WDM Systems

    DEFF Research Database (Denmark)

    Hübner, Jörg; Varming, Poul; Kristensen, Martin

    1997-01-01

    Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of <15 kHz and a sidemode suppression better than 61 dB are presented. The stability of the lasers is verified by a 10 Gbit/s transmission experiment. Five DFB fibre lasers are cascaded and pumped by a single semicondu......Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of pumped by a single...

  17. Quality of scintillating fibres after hot bump shrinking

    CERN Document Server

    Rodrigues Cavalcante, Ana Barbara; Joram, Christian

    2016-01-01

    Shrinking the diameter of fibre bumps by a hot drawing tool requires to run the fibre through the hot tool over its full length, bearing the risk of a degradation of the fibre performance. In this study we demonstrated that the hot bump shrinking method has no visible effect on the optical attenuation length, the light yield following ionising radiation, the diameter, the mechanical stability and the integrity of the cladding. For the latter, even a small positive impact was observed.

  18. Design of macro-synthetic fibre reinforced concrete pipes

    OpenAIRE

    Fuente, Albert de la; Escariz, Renata Campos; Figueiredo,Antonio Domingues de; Aguado, Antonio

    2013-01-01

    This paper presents an experimental campaign in which concrete pipes were manufactured using plastic fibres as the sole reinforcement material. In this regard, it has been demonstrated that the use of plastic fibres is compatible with pipe production systems, and that, when subjected to the crushing test (CT), plastic fibre reinforced pipes yield strength classes that are attractive in terms of the growth of this material in the concrete pipe industry. Moreover, the results obtained from b...

  19. Microwave absorbing properties of activated carbon fibre polymer composites

    Indian Academy of Sciences (India)

    Tianchun Zou; Naiqin Zhao; Chunsheng Shi; Jiajun Li

    2011-02-01

    Microwave absorption of composites containing activated carbon fibres (ACFs) was investigated. The results show that the absorptivity greatly depends on increasing ACF content in the absorbing layer, first increasing and then decreasing. When the content is 0.76 wt.%, the bandwidth below −10dB is 12.2 GHz. Comparing the absorption characteristics of the ACF composite with one containing unactivated fibres, it is found that carbon fibre activation increases the absorption of the composite.

  20. RESEARCH ON THE HYDRODYNAMIC STABILITY OF FIBRE SUSPENSIONS

    Institute of Scientific and Technical Information of China (English)

    You Zhen-jiang

    2003-01-01

    The stability of wall-bounded fibre suspensions was studied. The linear stability analysis was performed applying the flow stability theory and slender-body theory. The results of numerical analysis show that fibres and their hydrodynamic interactions reinforce the flow stability. Investigation of fibre orientation and vorticity in the suspension revealed the mechanisms behind the instability. Drag reduction properties in the transition regime were also presented. The experiments using dye emission and PIV techniques verified theoretical results.

  1. Fibre Optic Biosensor Assay of Newcastle Disease Virus

    Science.gov (United States)

    1993-10-01

    A fluorometric sandwich immunoassay for Newcastle disease virus (NDV) was developed using a fibre optic biosensor. Antibodies directed against NDV...and low baseline variation. These and other properties of the fibre optic biosensor indicate that it has the potential to serve as an on-line...continuous monitoring device of an automated or semiautomated detection system. As a part of the fibre optic biosensor development, the surface coverage of

  2. Guidance in Kagome-like photonic crystal fibres I: analysis of an ideal fibre structure.

    Science.gov (United States)

    Chen, Lei; Pearce, Greg J; Birks, Timothy A; Bird, David M

    2011-03-28

    Propagation of light in a square-lattice hollow-core photonic crystal fibre is analysed as a model of guidance in a class of photonic crystal fibres that exhibit broad-band guidance without photonic bandgaps. A scalar governing equation is used and analytic solutions based on transfer matrices are developed for the full set of modes. It is found that an exponentially localised fundamental mode exists for a wide range of frequencies. These analytic solutions of an idealised structure will form the basis for analysis of guidance in a realistic structure in a following paper.

  3. Dust ablation in Pluto's atmosphere

    Science.gov (United States)

    Horanyi, Mihaly; Poppe, Andrew; Sternovsky, Zoltan

    2016-04-01

    Based on measurements by dust detectors onboard the Pioneer 10/11 and New Horizons spacecraft the total production rate of dust particles born in the Edgeworth Kuiper Belt (EKB) has been be estimated to be on the order of 5 ṡ 103 kg/s in the approximate size range of 1 - 10 μm. Dust particles are produced by collisions between EKB objects and their bombardment by both interplanetary and interstellar dust particles. Dust particles of EKB origin, in general, migrate towards the Sun due to Poynting-Robertson drag but their distributions are further sculpted by mean-motion resonances as they first approach the orbit of Neptune and later the other planets, as well as mutual collisions. Subsequently, Jupiter will eject the vast majority of them before they reach the inner solar system. The expected mass influx into Pluto atmosphere is on the order of 200 kg/day, and the arrival speed of the incoming particles is on the order of 3 - 4 km/s. We have followed the ablation history as function of speed and size of dust particles in Pluto's atmosphere, and found that volatile rich particles can fully sublimate due to drag heating and deposit their mass in narrow layers. This deposition might promote the formation of the haze layers observed by the New Horizons spacecraft. This talk will explore the constraints on the composition of the dust particles by comparing the altitude of the deposition layers to the observed haze layers.

  4. Giant muscle fibres in pigs with different Ryr1 genotype.

    Science.gov (United States)

    Fazarinc, G; Candek-Potokar, M; Ursic, M; Vrecl, M; Pogacnik, A

    2002-12-01

    This study examined the frequency, morphological and immunohistochemical characteristics of the giant fibres in the longissimus muscle of local Krsko polje pigs with different Ryr1 genotypes. Giant fibres were round-shaped and had significantly increased cross-sectional area compared with normal muscle fibres. Only fast-twitch glycolytic fibres were affected, usually showing enhanced succinate dehydrogenase activity. On the ultrastructural level, the dilation of the sarcoplasmic reticulum, swelling of mitochondria and destruction of myofilaments was observed. The incidence of giant fibres was the highest in Ryr1 dimutant pigs (Ryr1 nn), which also exhibited lower muscle pH1 than heterozygous (Ryr1 Nn) or pigs with the wild Ryr1 gene (Ryr1 NN). However, the giant fibres were also present in pigs free of Ryr1 gene mutation. Our results suggest that the giant fibre syndrome depends mostly upon the rate and intensity of early post-mortem glycolysis, which results in acidity of muscle tissue. We suppose that the giant fibre formation is a result of excessive intracellular lactate accumulation in some fast-twitch glycolytic fibres. This process could also explain the ultrastructural alterations and the consequent changes in the oxidative enzymes and myofibrillar ATPase staining pattern observed in our and some previous studies.

  5. A 24mm diameter fibre positioner for spectroscopic surveys

    Science.gov (United States)

    Hörler, Philipp; Kronig, Luzius; Kneib, Jean-Paul; Bleuler, Hannes; Bouri, Mohamed

    2016-07-01

    One of the big research topics in modern cosmology is the mystery of dark Energy. To unveil the secret, cosmologists want to measure precisely the evolution of large scale structures in the universe. One way of doing so is to measure the 3D location of a high number of galaxies. By measuring the redshift of a galaxy, it is possible to find its distance. In order to measure a high number of galaxies in a practical amount of time, we need to observe multiple objects in parallel. Instead of a spectrograph, thousands of optical fibres are placed in the focal plane of a telescope. They will transmit the light of many objects to a spectrograph. Each fibre has to be positioned to several μm precision in the focal plane of a telescope for each exposure. Each fibre is positioned by a 2-axis fibre positioner. In this paper such a fibre positioner with 24-mm diameter is presented. It is driven by two brushless DC motors in combination with a backlash free gearbox. The positioner has an optimal central fibre path and improved angular alignment. The fibre runs through the centre of the positioner and is only bent at the top to reach its target position. In this way, the flexion and torsion of the fibre are minimal. In addition to the high positioning accuracy, the design is optimized to allow a minimal tilt error of the fibre. This is demonstrated using a novel optical tilt measurement system.

  6. Prediction of fibre architecture and adaptation in diseased carotid bifurcations.

    LENUS (Irish Health Repository)

    Creane, Arthur

    2011-12-01

    Many studies have used patient-specific finite element models to estimate the stress environment in atherosclerotic plaques, attempting to correlate the magnitude of stress to plaque vulnerability. In complex geometries, few studies have incorporated the anisotropic material response of arterial tissue. This paper presents a fibre remodelling algorithm to predict the fibre architecture, and thus anisotropic material response in four patient-specific models of the carotid bifurcation. The change in fibre architecture during disease progression and its affect on the stress environment in the plaque were predicted. The mean fibre directions were assumed to lie at an angle between the two positive principal strain directions. The angle and the degree of dispersion were assumed to depend on the ratio of principal strain values. Results were compared with experimental observations and other numerical studies. In non-branching regions of each model, the typical double helix arterial fibre pattern was predicted while at the bifurcation and in regions of plaque burden, more complex fibre architectures were found. The predicted change in fibre architecture in the arterial tissue during plaque progression was found to alter the stress environment in the plaque. This suggests that the specimen-specific anisotropic response of the tissue should be taken into account to accurately predict stresses in the plaque. Since determination of the fibre architecture in vivo is a difficult task, the system presented here provides a useful method of estimating the fibre architecture in complex arterial geometries.

  7. Crosstalk-Managed Heterogeneous Single-Mode 32-Core Fibre

    DEFF Research Database (Denmark)

    Sasaki, Y.; Fukumoto, Ryohei; Takenaga, Katsuhiro

    2016-01-01

    A heterogeneous single-mode 32-core fibre with a cladding diameter of 243 micrometer is designed and fabricated. The highest core count in single-mode multi-core fibres and low worst-case crosstalk of less than -24 dB/1000 km in C-band are achieved simultaneously.......A heterogeneous single-mode 32-core fibre with a cladding diameter of 243 micrometer is designed and fabricated. The highest core count in single-mode multi-core fibres and low worst-case crosstalk of less than -24 dB/1000 km in C-band are achieved simultaneously....

  8. Power transmission coefficients for multi-step index optical fibres.

    Science.gov (United States)

    Aldabaldetreku, Gotzon; Zubia, Joseba; Durana, Gaizka; Arrue, Jon

    2006-02-20

    The aim of the present paper is to provide a single analytical expression of the power transmission coefficient for leaky rays in multi-step index (MSI) fibres. This expression is valid for all tunnelling and refracting rays and allows us to evaluate numerically the power attenuation along an MSI fibre of an arbitrary number of layers. We validate our analysis by comparing the results obtained for limit cases of MSI fibres with those corresponding to step-index (SI) and graded-index (GI) fibres. We also make a similar comparison between this theoretical expression and the use of the WKB solutions of the scalar wave equation.

  9. Semiconductor optical fibres for infrared applications: A review

    Science.gov (United States)

    Peacock, Anna C.; Healy, Noel

    2016-10-01

    Over the last decade a new class of optical fibre has emerged that incorporates semiconductor materials within the core. These fibres are rich in optoelectronic functionality and offer extended transmission bands across the infrared spectral region so that their application potential is vast. Various fabrication methods have been developed to produce fibres with a range of unary and compound semiconductor core materials, which can be either amorphous or crystalline in form. This review discusses the main fabrication procedures and the infrared optical properties of the semiconductor fibres that have been fabricated to date, then takes a look at the future prospects of this exciting new technology.

  10. Relativistic Corrections for Time and Frequency Transfer in Optical Fibres

    CERN Document Server

    Geršl, J; Wolf, P

    2016-01-01

    We derive relativistic corrections for one-way and two-way time and frequency transfer over optical fibres neglecting no terms that exceed 1 ps in time and $10^{-18}$ in fractional frequency, and estimate their magnitude in typical fibre links. We also provide estimates of the uncertainties in the evaluation of the relativistic corrections due to imperfect knowledge of parameters like the coordinates of the fibre and stations, Earth rotation, or thermal effects of the fibre index and length. The links between Teddington(UK) and Paris(F) as well as Braunschweig(D) and Paris(F), that are currently under construction, are studied as specific examples.

  11. Durabilité des fibres polyaramides en milieu alcalin

    OpenAIRE

    Derombise, Guillaume; LABORATOIRE CENTRAL DES PONTS ET CHAUSSEES - LCPC

    2007-01-01

    Les fibres polyamides aromatiques, appelées plus couramment "fibres aramides", sont des fibres polymères synthétiques à forte anisotropie. Ces fibres "hautes performances" présentent en outre un module élevé, une résistance mécanique et une rigidité excellentes ainsi qu'une faible densité et une grande résistance thermique qui ont rendu leur utilisation intéressante dans des applications telles que les vêtements de protection contre le feu, la balistique, les matériaux composites, la câblerie...

  12. Spider silk: a novel optical fibre for biochemical sensing

    Science.gov (United States)

    Hey Tow, Kenny; Chow, Desmond M.; Vollrath, Fritz; Dicaire, Isabelle; Gheysens, Tom; Thévenaz, Luc

    2015-09-01

    Whilst being thoroughly used in the textile industry and biomedical sector, silk has not yet been exploited for fibre optics-based sensing although silk fibres directly obtained from spiders can guide light and have shown early promises to being sensitive to some solvents. In this communication, a pioneering optical fibre sensor based on spider silk is reported, demonstrating for the first time the use of spider silk as an optical fibre sensor to detect polar solvents such as water, ammonia and acetic acid.

  13. CAPSULES AS A PREVENTION OF FIBRE CLUSTERS IN CONCRETE

    Directory of Open Access Journals (Sweden)

    JOSEF STRYK

    2012-12-01

    Full Text Available Homogenous concrete mixture without aggregate pockets and fibre clusters is a presumption for appropriate properties of concrete element or structure. There are technological measures how to achieve homogenously looking mixture from aggregate point of view, but fibres are still predisposed for clusters forming. The paper evaluates originally designed and protected within European patent treatment of fibre, based on capsules containing individual rolled fibre which can be admixed into a concrete mixture and set up homogenously in its whole volume within the mixing process.

  14. Fibre content and physiochemical properties of various horse feed ingredients

    DEFF Research Database (Denmark)

    Brøkner, Christine; Knudsen, Knud Erik Bach; Tauson, Anne-Helene

    2010-01-01

    There is an increasing need for identifying energy dense feed ingredients based on fibre, as starch has been shown to cause health problems in sports horses (Kronfeld et al., 2005). This experiment aimed at evaluating feeds considered to be suitable for horses by use of an enzymatic......-chemical dietary fibre (DF) analytical method compared with conventional analytical methods of crude fibre (CF) and neutral detergent fibre (NDF). We expect the DF method to provide detailed and useful information concerning the nutritional properties of feed ingredients for horses....

  15. Developing consumer acceptable biscuits enriched with Psyllium fibre

    National Research Council Canada - National Science Library

    Fradinho, Patricia; Nunes, M Cristiana; Raymundo, Anabela

    .... The incorporation of solid components on the biscuit dough, such as dietary fibre, could have serious implications on its structure and perceived texture which explains the technological limitations...

  16. Lunar Dust Mitigation Technology Development

    Science.gov (United States)

    Hyatt, Mark J.; Deluane, Paul B.

    2008-01-01

    NASA s plans for implementing the Vision for Space Exploration include returning to the moon as a stepping stone for further exploration of Mars, and beyond. Dust on the lunar surface has a ubiquitous presence which must be explicitly addressed during upcoming human lunar exploration missions. While the operational challenges attributable to dust during the Apollo missions did not prove critical, the comparatively long duration of impending missions presents a different challenge. Near term plans to revisit the moon places a primary emphasis on characterization and mitigation of lunar dust. Comprised of regolith particles ranging in size from tens of nanometers to microns, lunar dust is a manifestation of the complex interaction of the lunar soil with multiple mechanical, electrical, and gravitational effects. The environmental and anthropogenic factors effecting the perturbation, transport, and deposition of lunar dust must be studied in order to mitigate it s potentially harmful effects on exploration systems. This paper presents the current perspective and implementation of dust knowledge management and integration, and mitigation technology development activities within NASA s Exploration Technology Development Program. This work is presented within the context of the Constellation Program s Integrated Lunar Dust Management Strategy. The Lunar Dust Mitigation Technology Development project has been implemented within the ETDP. Project scope and plans will be presented, along with a a perspective on lessons learned from Apollo and forensics engineering studies of Apollo hardware. This paper further outlines the scientific basis for lunar dust behavior, it s characteristics and potential effects, and surveys several potential strategies for its control and mitigation both for lunar surface operations and within the working volumes of a lunar outpost.

  17. Myosin heavy-chain isoform distribution, fibre-type composition and fibre size in skeletal muscle of patients on haemodialysis

    DEFF Research Database (Denmark)

    Molsted, Stig; Eidemak, Inge; Sorensen, Helle Tauby;

    2007-01-01

    Objective. Chronic uraemia is associated with abnormalities in skeletal muscles, which can affect their working capacity. It is also well known that the fibre-type composition of skeletal muscles influences endurance, muscle strength and power. In this study we therefore determined the size...... and distribution of muscle fibres and the myosin heavy-chain (MHC) isoform composition in patiens on haemodialysis (HD) in order to establish any differences with values for untrained control subjects. Material and methods. Muscle biopsies were obtained from the vastus lateralis muscle of 14 non-diabetic patients...... determined fibre-type composition of the vastus lateralis muscle. The mean fibre area of type 1 and 2 fibres was 3283±873 and 3594±1483 µm2, respectively. The MHC composition and the size of the type 1 fibres of the patients on HD were significantly different from those of the control subjects. Conclusions...

  18. Experimental Investigation and Analysis of Mechanical Properties of Palm fibre reinforced Epoxy composites and Sisal fibre reinforced Polyester composites

    Directory of Open Access Journals (Sweden)

    B. Muthu Chozha Rajan

    2015-12-01

    Full Text Available The objective of this paper was investigated to evaluate tensile, flexural and Impact properties of Palm fibre reinforced Epoxy composites (PFRP and compared with Sisal fibre reinforced Polyester composites (SFRP. Untreated chopped Palmyra Palm fruit fibre was used as reinforcement in Epoxy resin matrix and chopped sisal fibre was used as reinforcement in Polyester resin matrix. The chopped palm fibrereinforced composite were prepared in volume fractions (Vf such as 10 %, 20 % and 30 % of specimens by using Epoxy and the chopped sisalfibre reinforced composite were prepared in volume fractions (Vf such as 10 %, 20 % and 30 % of specimens by using Polyester. The specimens are tested for their mechanical Properties strictly as per ASTM procedures. Static analysis is performed by FEA based software ANSYS R15 with design constraints as Equivalent stress, Shear stress and deflection.The experimental result and analysis shows that the fibre volume fraction increases the tensile, flexural, Impact strength and modulus of the fibre reinforced composites

  19. Dust Storms: Why Are Dust Storms a Concern?

    Science.gov (United States)

    ... Radon Solvents Styrene Sulfur Dioxide Toluene Uranium Volatile Organic Compounds (VOCs) For Educators Introduction Tox Town-Based Curriculum Units / Science Club Careers in Environmental Health, Chemistry, and Toxicology More Resources Dust Storms en español ...

  20. Dust Acoustic Wave Excitation in a Plasma with Warm Dust

    Science.gov (United States)

    Rosenberg, M.; Thomas, E., Jr.; Marcus, L.; Fisher, R.; Williams, J. D.; Merlino, R. L.

    2008-11-01

    Measurements of the dust acoustic wave dispersion relation in dusty plasmas formed in glow discharges at the University of Iowa [1] and Auburn University [2] have shown the importance of finite dust temperature effects. The effect of dust grains with large thermal speeds was taken into account using kinetic theory of the ion-dust streaming instability [3]. The results of analytic and numerical calculations of the dispersion relation based on the kinetic theory will be presented and compared with the experimental results. [1] E. Thomas, Jr., R. Fisher, and R. L. Merlino, Phys. Plasmas 14, 123701 (2007). [2] J. D. Williams, E. Thomas Jr., and L. Marcus, Phys. Plasmas 15, 043704 (2008). [3] M. Rosenberg, E. Thomas Jr., and R. L. Merlino, Phys. Plasmas 15, 073701 (2008).