WorldWideScience

Sample records for dual-color dfb fibre

  1. Design of DFB fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Povlsen, Jørn Hedegaard; Varming, Poul

    1998-01-01

    A numerical model for erbium distributed feedback (DFB) fibre lasers is presented. The model is used to optimise the location of a discrete phase-shift to obtain maximum output power. For DFB fibre lasers of up to 10cm in length it is shown that the influence of Kerr nonlinearity with respect...

  2. Polarisation control of DFB fibre lasers

    DEFF Research Database (Denmark)

    Varming, Poul; Philipsen, Jacob Lundgreen; Berendt, Martin Ole

    1998-01-01

    The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser......The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser...

  3. Dynamic response analysis of DFB fibre lasers

    DEFF Research Database (Denmark)

    Yujun, Qian; Varming, Poul; Povlsen, Jørn Hedegaard

    1998-01-01

    We present a model for relative intensity noise (RIN) in DFB fibre lasers which predicts measured characteristics accurately. Calculation results implies that the RIN decreases rapidly with stronger Bragg grating and higher pump power. We propose here a simplified model based on three spatially...... independent rate equations to describe the dynamic response of erbium doped DFB fibre lasers on pump power fluctuations, using coupled-mode theory to calculate the steady-state hole-burning of the erbium ion inversion...

  4. Five Wavelength DFB Fibre Laser Source for WDM Systems

    DEFF Research Database (Denmark)

    Hübner, Jörg; Varming, Poul; Kristensen, Martin

    1997-01-01

    Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of <15 kHz and a sidemode suppression better than 61 dB are presented. The stability of the lasers is verified by a 10 Gbit/s transmission experiment. Five DFB fibre lasers are cascaded and pumped by a single semicondu......Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of pumped by a single...

  5. Five Wavelength DFB Fibre Laser Source for WDM Systems

    DEFF Research Database (Denmark)

    Hübner, Jörg; Varming, Poul; Kristensen, Martin

    1997-01-01

    Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of <15 kHz and a sidemode suppression better than 61 dB are presented. The stability of the lasers is verified by a 10 Gbit/s transmission experiment. Five DFB fibre lasers are cascaded and pumped by a single semicondu......Singlemode UV-induced distributed feedback (DFB) fibre lasers with a linewidth of pumped by a single...

  6. Highly Efficient L-Band Fibre -DFB Lasers

    Institute of Scientific and Technical Information of China (English)

    Libin Fu; Morten Ibsen; David J. Richardson; David N. Payne

    2003-01-01

    A more than 12 mW highly efficient fibre-DFB laser operating at 1618.3 nm is fabricated and characterised. Its high-power, low-noise and single-polarisation characteristics make it very suitable WDM-source for L-band transmission.

  7. Michelson Interferometer characterisation of noise reduction in DFB fibre lasers

    Science.gov (United States)

    Canagasabey, Albert; Jones, David; Mann, David; Canning, John; Fleming, Simon; Holdsworth, John

    2012-02-01

    A comparison is made between unpackaged and packaged distributed feedback (DFB) fibre lasers using the Michelson interferometer configuration for delayed self-heterodyne interferometery (MIDSHI) to ascertain the improvements to the external environmental noise, quantified by reductions in the Gaussian linewidth. Voigt fitting is used to extract and separate out the Lorentzian and Gaussian linewidth contributions and therefore the associated sources of noise. Significant improvements in the Gaussian linewidth were achieved as a result of significant reductions in the sensitivity of the DFB laser to external perturbations using packaging. However, a broadening of the laser Lorentzian linewidth was observed.

  8. Polarization-stable dual-color DFB fibre laser system for CW terahertz generation

    DEFF Research Database (Denmark)

    Eichhorn, Finn; Petersen, Jens Engholm; Jepsen, Peter Uhd

    The terahertz, or THz, frequency range represents a gap in technology as well as knowledge in the electromagnetic spectrum. The THz spectral range is here loosely defined as frequencies between 100 GHz and 10 THz. Electromagnetic waves at THz frequencies interact strongly with metals, ceramics...

  9. Polarization-stable dual-color DFB fibre laser system for CW terahertz generation

    DEFF Research Database (Denmark)

    Eichhorn, Finn; Petersen, Jens Engholm; Jepsen, Peter Uhd

    ” the walls of non-metallic containers as well as clothing to identify hidden objects. For this reason, large efforts are currently being put into the exploitation of the “THz gap” to investigate new applications in the safety and security sector as well as industrial environments. We have developed...

  10. Power-scalable, polarization-stable, dual-colour DFB fibre laser system for CW terahertz imaging

    DEFF Research Database (Denmark)

    Eichhorn, Finn; Pedersen, Jens Engholm; Jepsen, Peter Uhd

    -scalable, dual-colour, polarization-maintaining distributed feedback (DFB) fibre laser system with an inherent narrow linewidth from the DFB fibre laser oscillators. The laser system can be used as source in CW THz systems employing photomixing (optical heterodyning) for generation and detection...

  11. Polarisation Control of DFB Fibre Laser Using UV-Induced Birefringent Phase-Shift

    DEFF Research Database (Denmark)

    Philipsen, Jacob Lundgreen; Lauridsen, Vibeke Claudia; Berendt, Martin Ole;

    1998-01-01

    The polarisation properties of a distributed feedback (DFB) fibre laser are investigated experimentally. A birefringent phase-shift is induced by side illumination of the centre part of the lasing structure with ultraviolet (UV) light and it is experimentally shown that the birefringence of the p......The polarisation properties of a distributed feedback (DFB) fibre laser are investigated experimentally. A birefringent phase-shift is induced by side illumination of the centre part of the lasing structure with ultraviolet (UV) light and it is experimentally shown that the birefringence...

  12. Optimised design of fibre-based pulse compressor for gain-switched DFB laser pulses at 1.5 µm

    OpenAIRE

    Barry, Liam P.; Thomsen, Benn C.; Dudley, John M.; Harvey, John D.

    1999-01-01

    An optical-fibre based pulse compressor for gain-switched DFB laser pulses has been optimised using a systematic procedure based on the initial complete characterisation of the laser pulses, followed by numerical simulations of the pulse propagation in different types of fibre to determine the required lengths for optimum compression. Using both linear and nonlinear compression techniques, an optimum compression factor of 12 is achieved.

  13. Dual-Color Click Beetle Luciferase Heteroprotein Fragment Complementation Assays

    Science.gov (United States)

    Villalobos, Victor; Naik, Snehal; Bruinsma, Monique; Dothager, Robin S.; Pan, Mei-Hsiu; Samrakandi, Mustapha; Moss, Britney; Elhammali, Adnan; Piwnica-Worms, David

    2010-01-01

    Summary Understanding the functional complexity of protein interactions requires mapping biomolecular complexes within the cellular environment over biologically-relevant time scales. Herein we describe a novel set of reversible, multicolored heteroprotein complementation fragments based on various firefly and click beetle luciferases that utilize the same substrate, D-luciferin. Luciferase heteroprotein fragment complementation systems enabled dual-color quantification of two discreet pairs of interacting proteins simultaneously or two distinct proteins interacting with a third shared protein in live cells. Using real-time analysis of click beetle green and click beetle red luciferase heteroprotein fragment complementation applied to β-TrCP, an E3-ligase common to the regulation of both β-catenin and IκBα, GSK3β was identified as a novel candidate kinase regulating IκBα processing. These dual-color protein interaction switches may enable directed dynamic analysis of a variety of protein interactions in living cells. PMID:20851351

  14. 2000-fold parallelized dual-color STED fluorescence nanoscopy.

    Science.gov (United States)

    Bergermann, Fabian; Alber, Lucas; Sahl, Steffen J; Engelhardt, Johann; Hell, Stefan W

    2015-01-12

    Stimulated Emission Depletion (STED) nanoscopy enables multi-color fluorescence imaging at the nanometer scale. Its typical single-point scanning implementation can lead to long acquisition times. In order to unleash the full spatiotemporal resolution potential of STED nanoscopy, parallelized scanning is mandatory. Here we present a dual-color STED nanoscope utilizing two orthogonally crossed standing light waves as a fluorescence switch-off pattern, and providing a resolving power down to 30 nm. We demonstrate the imaging capabilities in a biological context for immunostained vimentin fibers in a circular field of view of 20 µm diameter at 2000-fold parallelization (i.e. 2000 "intensity minima"). The technical feasibility of massively parallelizing STED without significant compromises in resolution heralds video-rate STED nanoscopy of large fields of view, pending the availability of suitable high-speed detectors.

  15. Cost-effective wavelength selectable light source using DFB fiber laser array

    DEFF Research Database (Denmark)

    Liu, Fenghai; Xueyan, Zheng; Pedersen, Rune Johan Skullerud

    2000-01-01

    A cost-effective wavelength selectable light source comprising a distributed feedback (DFB) fibre laser array is proposed. A large number of wavelengths can be selected via optical space switches using only one shared pump laser. The structure is a good candidate for use as a wavelength selectabl...

  16. Dual-Colored DNA Comb Polymers for Single Molecule Rheology

    Science.gov (United States)

    Mai, Danielle; Marciel, Amanda; Schroeder, Charles

    2014-03-01

    We report the synthesis and characterization of branched biopolymers for single molecule rheology. In our work, we utilize a hybrid enzymatic-synthetic approach to graft ``short'' DNA branches to ``long'' DNA backbones, thereby producing macromolecular DNA comb polymers. The branches and backbones are synthesized via polymerase chain reaction with chemically modified deoxyribonucleotides (dNTPs): ``short'' branches consist of Cy5-labeled dNTPs and a terminal azide group, and ``long'' backbones contain dibenzylcyclooctyne-modified (DBCO) dNTPs. In this way, we utilize strain-promoted, copper-free cycloaddition ``click'' reactions for facile grafting of azide-terminated branches at DBCO sites along backbones. Copper-free click reactions are bio-orthogonal and nearly quantitative when carried out under mild conditions. Moreover, comb polymers can be labeled with an intercalating dye (e.g., YOYO) for dual-color fluorescence imaging. We characterized these materials using gel electrophoresis, HPLC, and optical microscopy, with atomic force microscopy in progress. Overall, DNA combs are suitable for single molecule dynamics, and in this way, our work holds the potential to improve our understanding of topologically complex polymer melts and solutions.

  17. DFB component production at IHEP complete

    CERN Multimedia

    2007-01-01

    1. LHC project leader Lyn Evans receiving a model of a DFB from IHEP general director Nikolaj Tyurin.2. Collective photo of DFB celebration at IHEP. Participants from left: V. Sytchev, V. Benda, N. Tyurin, A. Zaytcev, L. Evans, A. Perin, R. van Weelderen, Ph. Trilhe, M. Genet, L. Tavian, Ph. Lebrun, A. Kleshov.

  18. A new approach to dual-color two-photon microscopy with fluorescent proteins

    Directory of Open Access Journals (Sweden)

    Rebane Aleks

    2010-02-01

    Full Text Available Abstract Background Two-photon dual-color imaging of tissues and cells labeled with fluorescent proteins (FPs is challenging because most two-photon microscopes only provide one laser excitation wavelength at a time. At present, methods for two-photon dual-color imaging are limited due to the requirement of large differences in Stokes shifts between the FPs used and their low two-photon absorption (2PA efficiency. Results Here we present a new method of dual-color two-photon microscopy that uses the simultaneous excitation of the lowest-energy electronic transition of a blue fluorescent protein and a higher-energy electronic transition of a red fluorescent protein. Conclusion Our method does not require large differences in Stokes shifts and can be extended to a variety of FP pairs with larger 2PA efficiency and more optimal imaging properties.

  19. Dual-color decompositions at one-loop level in Yang-Mills theory

    CERN Document Server

    Du, Yi-Jian; Fu, Chih-Hao

    2014-01-01

    In this work, we extend the construction of dual color decomposition in Yang-Mills theory to one-loop level, i.e., we show how to write one-loop integrands in Yang-Mills theory to the dual DDM-form and the dual trace-form. In dual forms, integrands are decomposed in terms of color-ordered one-loop integrands for color scalar theory with proper dual color coefficients.In dual DDM decomposition, The dual color coefficients can be obtained directly from BCJ-form by applying Jacobi-like identities for kinematic factors. In dual trace decomposition, the dual trace factors can be obtained by imposing one-loop KK relations, reflection relation and their relation with the kinematic factors in dual DDM-form.

  20. Five wavelength DFB fiber lase source

    DEFF Research Database (Denmark)

    Varming, Poul; Hübner, Jörg; Kristensen, M.

    1997-01-01

    Stable single-mode laser sources with narrow linewidth are key components in high-capacity wavelength-division multiplexed (WDM) optical communication systems. Distributed feedback (DFB) and distributed Bragg reflection (DBR) fiber lasers are compact devices, which are able to provide stable single......-mode operation. They are inherently fiber compatible and cascadable. We present a multiwavelength laser source consisting of five fiber DFB lasers spliced together and pumped by a single 60-mW 1480-nm semiconductor laser...

  1. Routine dual-color immunostaining with a 3-antibody cocktail improves the detection of small cancers in prostate needle biopsies.

    Science.gov (United States)

    Tolonen, Teemu T; Kujala, Paula M; Laurila, Marita; Tirkkonen, Mika; Ilvesaro, Joanna; Tuominen, Vilppu J; Tammela, Teuvo L J; Isola, Jorma

    2011-11-01

    We performed dual-color immunostaining with a 3-antibody cocktail (α-methylacyl coenzyme-A racemase, CK34betaE12, and p63) on prostate biopsies from 200 patients. Current practice (hematoxylin and eosin staining followed by dual-color immunostaining on selected cases) was compared with a protocol in which routine dual-color immunostaining was provided in all cases. In the original pathology reports, adenocarcinoma was diagnosed in 87/200 (43%) patients. Small foci interpreted as putative cancers were detected with dual-color immunostaining in 14/113 patients who were originally diagnosed with a nonmalignant lesion. All of the suggested cancerous foci were independently reevaluated by 5 pathologists. A diagnosis of adenocarcinoma was assessed by consensus in 8 cases, and atypical small acinar proliferation was diagnosed in 1 case. Consensus was not reached in 5 cases. Six of the foci reclassified as cancer were of Gleason score 3 + 3 = 6, while 2 were graded as Gleason score 4 + 4 = 8. The feasibility of routine dual-color immunostaining was also tested by analyzing the time spent on microscopic assessment. Because small, atypical lesions expressing α-methylacyl coenzyme-A racemase (blue chromogen) were easy to detect using dual-color immunostaining, the microscopic analysis of dual-color immunostaining and hematoxylin-eosin staining was faster than that of hematoxylin-eosin staining alone that was later followed by dual-color immunostaining in selected cases (median 251 seconds versus 299 seconds, P < .0001). We concluded that routine dual-color immunostaining of all prostate biopsies would produce better diagnostic sensitivity with a smaller microscopy workload for the pathologist. However, minute foci interpreted as cancer with dual-color immunostaining need to be confirmed with hematoxylin-eosin staining, and minimal criteria for a definitive diagnosis of cancer are still lacking. Copyright © 2011 Elsevier Inc. All rights reserved.

  2. DFB laser with attached external intensity modulator

    Energy Technology Data Exchange (ETDEWEB)

    Marcuse, D. (AT and T Bell Labs. Holmdel, NJ (US))

    1990-02-01

    This paper presents a theoretical study of the frequency pulling effect exerted on a DFB laser by an external amplitude modulator that is directly attached to it. The modulator consists of a piece of waveguide whose loss is modulated by means of an externally applied voltage. The modulator affects the laser due to residual reflections from its far end which appear as a variable effective reflectivity to the output end of the DFB laser. Modulation affects the magnitude as well as the phase of the effective reflection coefficient presented to the laser due to the coupling of the real and imaginary parts of the effective refractive index of the modulator waveguide. The tuning problem is formulated as an eigenvalue equation for the DFB laser in the presence of an externally attached lossy cavity.

  3. Tunable Optofluidic Third Order DFB Dye Laser

    DEFF Research Database (Denmark)

    Gersborg-Hansen, Morten; Kristensen, Anders

    2007-01-01

    We present a low-threshold polymer-based nanofluidic dye laser. By employing a third order DFB laser resonator, we demonstrate a threshold fluence of ~7 muJ/mm2 and a tunability of 45 nm using a single laser dye......We present a low-threshold polymer-based nanofluidic dye laser. By employing a third order DFB laser resonator, we demonstrate a threshold fluence of ~7 muJ/mm2 and a tunability of 45 nm using a single laser dye...

  4. Eu/Tb codoped spindle-shaped fluorinated hydroxyapatite nanoparticles for dual-color cell imaging.

    Science.gov (United States)

    Ma, Baojin; Zhang, Shan; Qiu, Jichuan; Li, Jianhua; Sang, Yuanhua; Xia, Haibing; Jiang, Huaidong; Claverie, Jerome; Liu, Hong

    2016-06-02

    Lanthanide doped fluorinated hydroxyapatite (FAp) nanoparticles are promising cell imaging nanomaterials but they are excited at wavelengths which do not match the light sources usually found in a commercial confocal laser scanning microscope (CLSM). In this work, we have successfully prepared spindle-shaped Eu/Tb codoped FAp nanoparticles by a hydrothermal method. Compared with single Eu doped FAp, Eu/Tb codoped FAp can be excited by a 488 nm laser, and exhibit both green and red light emission. By changing the amounts of Eu and Tb peaks, the emission in the green region (500-580 nm) can be decreased to the benefit of the emission in the red region (580-720 nm), thus reaching a balanced dual color emission. Using MC3T3-E1 cells co-cultured with Eu/Tb codoped FAp nanoparticles, it is observed that the nanoparticles are cytocompatible even at a concentration as high as 800 μg ml(-1). The Eu/Tb codoped FAp nanoparticles are located in the cytoplasm and can be monitored by dual color-green and red imaging with a single excitation light at 488 nm. At a concentration of 200 μg ml(-1), the cytoplasm is saturated in 8 hours, and Eu/Tb codoped FAp nanoparticles retain their fluorescence for at least 3 days. The cytocompatible Eu/Tb codoped FAp nanoparticles with unique dual color emission will be of great use for cell and tissue imaging.

  5. CaRuby-Nano: a novel high affinity calcium probe for dual color imaging.

    Science.gov (United States)

    Collot, Mayeul; Wilms, Christian D; Bentkhayet, Asma; Marcaggi, Païkan; Couchman, Kiri; Charpak, Serge; Dieudonné, Stéphane; Häusser, Michael; Feltz, Anne; Mallet, Jean-Maurice

    2015-03-31

    The great demand for long-wavelength and high signal-to-noise Ca(2+) indicators has led us to develop CaRuby-Nano, a new functionalizable red calcium indicator with nanomolar affinity for use in cell biology and neuroscience research. In addition, we generated CaRuby-Nano dextran conjugates and an AM-ester variant for bulk loading of tissue. We tested the new indicator using in vitro and in vivo experiments demonstrating the high sensitivity of CaRuby-Nano as well as its power in dual color imaging experiments.

  6. Detection of Embryo Sex Chromosome by Dual Color Fluorescent In-Situ Hybridization

    Institute of Scientific and Technical Information of China (English)

    刘群; 朱桂金

    2003-01-01

    Summary: In order to evaluate the effects of sex chromosomal mosaicism on the accuracy of single-cell gender diagnosis, sex chromosomes of 21 normal fertilized embryos were detected by dual colorfluorescent in-situ hybridization (FISH). The results showed that 4 embryos had sex chromosomalmosaicism (19%) and the remaining 17 showed uniformly XX or XY signals in all blastomeres. Inconclusion, identification of sex by dual color FISH analysis of a single cell was accurate and efficient,and sex chromosomal mosaicism would not affect preimplantation gender diagnosis.

  7. DFB component production at IHEP complete

    CERN Multimedia

    2007-01-01

    The last of the components for the 42 DFBs (electrical distribution boxes feeding the strings of superconducting magnets in the LHC) produced for CERN by IHEP Protvino (Russia) were delivered to CERN in January 2007. The DFBs will provide the electrical supply for the superconducting magnets for the LHC, making possible the transition from room temperature down to -268ºC (4.5 K) (see Bulletin No. 37/2006). This important achievement was celebrated on the 14th February 2007 at the IHEP House of Scientists in Protvino in the presence of all the IHEP personnel who contributed to the DFB components production, and with the participation of eight delegates from CERN Management and CERN engineers involved in DFB production. Lyn Evans handed over a present symbolizing the IHEP-CERN collaboration to Nikolaj Tyurin, who offered to Lyn Evans a model of a DFB. Since August 2005, when the components for the first two boxes arrived at CERN, a total of 360 tonnes of raw materials were transported to IHEP on 19 lorries...

  8. In vivo cell kinetics of the bone marrow transplantation using dual colored transgenic rat system

    Science.gov (United States)

    Kai, Kotaro; Teraoka, Satoshi; Adachi, Yasushi; Ikehara, Susumu; Murakami, Takashi; Kobayashi, Eiji

    2008-02-01

    Because bone marrow is an adequate site for bone marrow stem cells, intra-bone marrow - bone marrow transplantation (IBM-BMT) is an efficient strategy for bone marrow transplantation (BMT). However, the fate of the transplanted cells remains unclear. Herein, we established a dual-colored transgenic rat system utilizing green fluorescent protein (GFP) and a luciferase (luc) marker. We then utilized this system to investigate the in vivo kinetics of transplanted bone marrow cells (BMCs) after authentic intravenous (IV)-BMT or IBM-BMT. The in vivo fate of the transplanted cells was tracked using an in vivo luminescent imaging technique; alterations in peripheral blood chimerism were also followed using flow cytometry. IBM-BMT and IV-BMT were performed using syngeneic and allogeneic rat combinations. While no difference in the proliferation pattern was observed between the two treatment groups at 7 days after BMT, different distribution patterns were clearly observed during the early phase. In the IBM-BMT-treated rats, the transplanted BMCs were engrafted immediately at the site of the injected bone marrow and expanded more rapidly than in the IV-BMT-treated rats during this phase. Graft-versus-host disease was also visualized. Our bio-imaging system using dual-colored transgenic rats is a powerful tool for performing quantitative and morphological assessments in vivo.

  9. Dual-color encoded DNAzyme nanostructures for multiplexed detection of intracellular metal ions in living cells.

    Science.gov (United States)

    Zhou, Wenjiao; Liang, Wenbing; Li, Daxiu; Yuan, Ruo; Xiang, Yun

    2016-11-15

    The detection of intracellular metal ions is of great importance in understanding metal homeostasis in cells and related diseases, and yet it remains a significant challenge to achieve this goal. Based on a new self-assembled and dual-color encoded DNAzyme nanostructure, we describe here an approach for multiplexed sensing of UO2(2+) and Pb(2+) in living cells. The fluorescently quenched nanoprobes can be prepared by simple thermal annealing of four ssDNAs containing the metal ion-dependent enzymatic and substrate sequences. The self-assembly formation of the nanostructures are verified by native polyacrylamide gel electrophoresis. The target metal ions can cleave the substrate sequences in the DNAzyme nanostructures to recover fluorescent emissions at different wavelengths for sensitive and selective in vitro multiplexed detection of UO2(2+) and Pb(2+) with the detection limits of 0.6nM and 3.9nM, respectively. Importantly, we demonstrate that these nanoprobes are stable in cell lysates and can enter cells without the aid of any transfection agents for simultaneous imaging intracellular UO2(2+) and Pb(2+). Moreover, the nanoprobes offer excellent biocompatibility and non-cytotoxicity. With these unique features, the dual-color encoded nanostructures presented here can thus offer new opportunities for multiplexed detection of specific intracellular species. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Super-Resolution Optical Fluctuation Bio-Imaging with Dual-Color Carbon Nanodots.

    Science.gov (United States)

    Chizhik, Anna M; Stein, Simon; Dekaliuk, Mariia O; Battle, Christopher; Li, Weixing; Huss, Anja; Platen, Mitja; Schaap, Iwan A T; Gregor, Ingo; Demchenko, Alexander P; Schmidt, Christoph F; Enderlein, Jörg; Chizhik, Alexey I

    2016-01-13

    Success in super-resolution imaging relies on a proper choice of fluorescent probes. Here, we suggest novel easily produced and biocompatible nanoparticles-carbon nanodots-for super-resolution optical fluctuation bioimaging (SOFI). The particles revealed an intrinsic dual-color fluorescence, which corresponds to two subpopulations of particles of different electric charges. The neutral nanoparticles localize to cellular nuclei suggesting their potential use as an inexpensive, easily produced nucleus-specific label. The single particle study revealed that the carbon nanodots possess a unique hybrid combination of fluorescence properties exhibiting characteristics of both dye molecules and semiconductor nanocrystals. The results suggest that charge trapping and redistribution on the surface of the particles triggers their transitions between emissive and dark states. These findings open up new possibilities for the utilization of carbon nanodots in the various super-resolution microscopy methods based on stochastic optical switching.

  11. Cellular resolution multiplexed FLIM tomography with dual-color Bessel beam.

    Science.gov (United States)

    Xu, Dongli; Zhou, Weibin; Peng, Leilei

    2017-02-01

    Fourier multiplexed FLIM (FmFLIM) tomography enables multiplexed 3D lifetime imaging of whole embryos. In our previous FmFLIM system, the spatial resolution was limited to 25 μm because of the trade-off between the spatial resolution and the imaging depth. In order to achieve cellular resolution imaging of thick specimens, we built a tomography system with dual-color Bessel beam. In combination with FmFLIM, the Bessel FmFLIM tomography system can perform parallel 3D lifetime imaging on multiple excitation-emission channels at a cellular resolution of 2.8 μm. The image capability of the Bessel FmFLIM tomography system was demonstrated by 3D lifetime imaging of dual-labeled transgenic zebrafish embryos.

  12. Dual-color ultrasensitive bright-field RNA in situ hybridization with RNAscope.

    Science.gov (United States)

    Wang, Hongwei; Su, Nan; Wang, Li-Chong; Wu, Xingyong; Bui, Son; Nielsen, Allissa; Vo, Hong-Thuy; Luo, Yuling; Ma, Xiao-Jun

    2014-01-01

    In situ hybridization (ISH) techniques have been important to the study of gene expression signatures in cells and tissues. The ability to detect multiple targets simultaneously is especially valuable, since it allows dissecting gene expression of distinct cell types with precise cellular and subcellular resolution within morphological context. Recently, we have reported using a novel dual-color ultrasensitive bright-field RNA in situ hybridization for detection of clonally restricted immunoglobulin light chain mRNA expression in B cell lymphomas. Here, we present detailed protocols of RNAscope 2-Plex assays for FFPE tissue sections. The protocols describe the tissue preparation, pretreatment, probe hybridization, signal amplification, visualization, and analysis, as well as emphasize the critical steps for ensuring successful staining.

  13. Dual-color plasmonic enzyme-linked immunosorbent assay based on enzyme-mediated etching of Au nanoparticles

    Science.gov (United States)

    Guo, Longhua; Xu, Shaohua; Ma, Xiaoming; Qiu, Bin; Lin, Zhenyu; Chen, Guonan

    2016-09-01

    Colorimetric enzyme-linked immunosorbent assay utilizing 3‧-3-5‧-5-tetramethylbenzidine(TMB) as the chromogenic substrate has been widely used in the hospital for the detection of all kinds of disease biomarkers. Herein, we demonstrate a strategy to change this single-color display into dual-color responses to improve the accuracy of visual inspection. Our investigation firstly reveals that oxidation state of 3‧-3-5‧-5-tetramethylbenzidine (TMB2+) can quantitatively etch gold nanoparticles. Therefore, the incorporation of gold nanoparticles into a commercial TMB-based ELISA kit could generate dual-color responses: the solution color varied gradually from wine red (absorption peak located at ~530 nm) to colorless, and then from colorless to yellow (absorption peak located at ~450 nm) with the increase amount of targets. These dual-color responses effectively improved the sensitivity as well as the accuracy of visual inspection. For example, the proposed dual-color plasmonic ELISA is demonstrated for the detection of prostate-specific antigen (PSA) in human serum with a visual limit of detection (LOD) as low as 0.0093 ng/mL.

  14. Dual-Color Fluorescence Imaging of Magnetic Nanoparticles in Live Cancer Cells Using Conjugated Polymer Probes.

    Science.gov (United States)

    Sun, Minjie; Sun, Bin; Liu, Yun; Shen, Qun-Dong; Jiang, Shaojun

    2016-03-02

    Rapid growth in biological applications of nanomaterials brings about pressing needs for exploring nanomaterial-cell interactions. Cationic blue-emissive and anionic green-emissive conjugated polymers are applied as dual-color fluorescence probes to the surface of negatively charged magnetic nanoparticles through sequentially electrostatic adsorption. These conjugated polymers have large extinction coefficients and high fluorescence quantum yield (82% for PFN and 62% for ThPFS). Thereby, one can visualize trace amount (2.7 μg/mL) of fluorescence-labeled nanoparticles within cancer cells by confocal laser scanning microscopy. Fluorescence labeling by the conjugated polymers is also validated for quantitative determination of the internalized nanoparticles in each individual cell by flow cytometry analysis. Extensive overlap of blue and green fluorescence signals in the cytoplasm indicates that both conjugated polymer probes tightly bind to the surface of the nanoparticles during cellular internalization. The highly charged and fluorescence-labeled nanoparticles non-specifically bind to the cell membranes, followed by cellular uptake through endocytosis. The nanoparticles form aggregates inside endosomes, which yields a punctuated staining pattern. Cellular internalization of the nanoparticles is dependent on the dosage and time. Uptake efficiency can be enhanced three-fold by application of an external magnetic field. The nanoparticles are low cytotoxicity and suitable for simultaneously noninvasive fluorescence and magnetic resonance imaging application.

  15. A Dual Color Immunohistochemistry Assay for Measurement of Cereblon in Multiple Myeloma Patient Samples.

    Science.gov (United States)

    Ren, Yan; Wang, Maria; Couto, Suzana; Hansel, Donna E; Miller, Karen; Lopez-Girona, Antonia; Bjorklund, Chad C; Gandhi, Anita K; Thakurta, Anjan; Chopra, Rajesh; Breider, Michael

    Clinical interest in the measurement of Cereblon (CRBN), the primary target of the IMiDs immunomodulatory drugs lenalidomide and pomalidomide, has been fueled by its essential requirement for antitumor or immunomodulatory activity of both drugs in multiple myeloma (MM). However, limited analyses of clinical samples for CRBN gene expression or protein levels have utilized unvalidated reagents and assays, raising uncertainty about the interpretation of these results. We previously described a highly specific rabbit monoclonal antibody CRBN65 against 65-76 AA of human Cereblon. Here we describe a validated dual color bright-field Cereblon/CD138 immunohistochemical (IHC) assay utilizing CRBN65 and a commercial mouse monoclonal CD138 antibody. Sensitivity and specificity of the assay was determined and assay precision was shown for both cytoplasmic and nuclear Cereblon in MM bone marrow samples with coefficient of variation values of 5% and 2%, respectively. The dual IHC assay was effective for detecting a continuous range of Cereblon levels in 22 MM patient bone marrow core biopsies and aspirate clots, as shown by average cytoplasmic H-scores ranging from 63 to 267 and nuclear H-scores ranging from 17 to 250. Interpathologist comparison of MM sample H-scores by 3 pathologists demonstrated good concordance (R=0.73). This dual assay demonstrated superior Cereblon IHC measurement in MM samples compared with the single IHC assay using a published commercial rabbit polyclonal Cereblon antibody and could be used to explore the potential utility of Cereblon as a biomarker in the clinic.

  16. Dual color photoactivation localization microscopy of cardiomyopathy-associated desmin mutants.

    Science.gov (United States)

    Brodehl, Andreas; Hedde, Per Niklas; Dieding, Mareike; Fatima, Azra; Walhorn, Volker; Gayda, Susan; Šarić, Tomo; Klauke, Bärbel; Gummert, Jan; Anselmetti, Dario; Heilemann, Mike; Nienhaus, Gerd Ulrich; Milting, Hendrik

    2012-05-01

    Mutations in the DES gene coding for the intermediate filament protein desmin may cause skeletal and cardiac myopathies, which are frequently characterized by cytoplasmic aggregates of desmin and associated proteins at the cellular level. By atomic force microscopy, we demonstrated filament formation defects of desmin mutants, associated with arrhythmogenic right ventricular cardiomyopathy. To understand the pathogenesis of this disease, it is essential to analyze desmin filament structures under conditions in which both healthy and mutant desmin are expressed at equimolar levels mimicking an in vivo situation. Here, we applied dual color photoactivation localization microscopy using photoactivatable fluorescent proteins genetically fused to desmin and characterized the heterozygous status in living cells lacking endogenous desmin. In addition, we applied fluorescence resonance energy transfer to unravel short distance structural patterns of desmin mutants in filaments. For the first time, we present consistent high resolution data on the structural effects of five heterozygous desmin mutations on filament formation in vitro and in living cells. Our results may contribute to the molecular understanding of the pathological filament formation defects of heterozygous DES mutations in cardiomyopathies.

  17. Dual Color Photoactivation Localization Microscopy of Cardiomyopathy-associated Desmin Mutants*

    Science.gov (United States)

    Brodehl, Andreas; Hedde, Per Niklas; Dieding, Mareike; Fatima, Azra; Walhorn, Volker; Gayda, Susan; Šarić, Tomo; Klauke, Bärbel; Gummert, Jan; Anselmetti, Dario; Heilemann, Mike; Nienhaus, Gerd Ulrich; Milting, Hendrik

    2012-01-01

    Mutations in the DES gene coding for the intermediate filament protein desmin may cause skeletal and cardiac myopathies, which are frequently characterized by cytoplasmic aggregates of desmin and associated proteins at the cellular level. By atomic force microscopy, we demonstrated filament formation defects of desmin mutants, associated with arrhythmogenic right ventricular cardiomyopathy. To understand the pathogenesis of this disease, it is essential to analyze desmin filament structures under conditions in which both healthy and mutant desmin are expressed at equimolar levels mimicking an in vivo situation. Here, we applied dual color photoactivation localization microscopy using photoactivatable fluorescent proteins genetically fused to desmin and characterized the heterozygous status in living cells lacking endogenous desmin. In addition, we applied fluorescence resonance energy transfer to unravel short distance structural patterns of desmin mutants in filaments. For the first time, we present consistent high resolution data on the structural effects of five heterozygous desmin mutations on filament formation in vitro and in living cells. Our results may contribute to the molecular understanding of the pathological filament formation defects of heterozygous DES mutations in cardiomyopathies. PMID:22403400

  18. Single-gene dual-color reporter cell line to analyze RNA synthesis in vivo.

    Science.gov (United States)

    Palangat, Murali; Larson, Daniel R

    2016-07-01

    RNA synthesis occurs through the multi-step process of transcription which consists of initiation, elongation, termination, and cleavage of the nascent RNA. In recent years, post-initiation events have attracted considerable attention as regulatory steps in gene expression. In particular, changes in elongation rate have been proposed to alter RNA fate either through changes in RNA secondary structure or recruitment of trans-acting factors, but systematic approaches for perturbing and measuring elongation rate are currently lacking. Here, we describe a system for precisely measuring elongation dynamics for single nascent transcripts at a single gene locus in human cell lines. The system is based on observing the production of fluorescently labeled RNA stem loops which flank a region of interest. The region of interest can be altered using flp recombinases, thus allowing one to study the effects of cis-acting sequences on transcription rate. The dual-color RNAs which are made during this process are exported and translated, thus enabling visualization of each step in gene expression.

  19. A UK NEQAS ISH multicenter ring study using the Ventana HER2 dual-color ISH assay.

    Science.gov (United States)

    Bartlett, J M S; Campbell, Fiona M; Ibrahim, Merdol; O'Grady, Anthony; Kay, Elaine; Faulkes, Catherine; Collins, Nadine; Starczynski, Jane; Morgan, John M; Jasani, Bharat; Miller, Keith

    2011-01-01

    We performed a multicenter assessment of a new HER2 dual-color chromogenic in situ hybridization (CISH) test and herein report on concordance of CISH data with fluorescence in situ hybridization (FISH) data and intraobserver and interlaboratory scoring consistency. HER2 results were evaluated using duplicate cores from 30 breast cancers in 5 laboratories using the Ventana HER2 dual-color ISH assay (Ventana Medical Systems, Cambridgeshire, England) and in 1 central laboratory using a standard FISH assay. Overall 93.3% of cases were successfully analyzed by CISH across the 5 participating laboratories. There was excellent concordance (98.0% overall) for diagnosis of HER2 amplification by CISH compared with FISH. Intraobserver variability (7.7%) and intersite variability (9.1%) of absolute HER2/chromosome enumeration probe 17 ratios were tightly controlled across all participating laboratories. The Ventana HER2 dual-color ISH assay is robust and reproducible, shows good concordance with a standard FISH assay, and complies with requirements in national and international guidelines for performance of ISH-based diagnostic tests.

  20. A UK NEQAS ISH multicenter ring study using the Ventana HER2 dual-color ISH assay.

    LENUS (Irish Health Repository)

    Bartlett, J M S

    2011-01-01

    We performed a multicenter assessment of a new HER2 dual-color chromogenic in situ hybridization (CISH) test and herein report on concordance of CISH data with fluorescence in situ hybridization (FISH) data and intraobserver and interlaboratory scoring consistency. HER2 results were evaluated using duplicate cores from 30 breast cancers in 5 laboratories using the Ventana HER2 dual-color ISH assay (Ventana Medical Systems, Cambridgeshire, England) and in 1 central laboratory using a standard FISH assay. Overall 93.3% of cases were successfully analyzed by CISH across the 5 participating laboratories. There was excellent concordance (98.0% overall) for diagnosis of HER2 amplification by CISH compared with FISH. Intraobserver variability (7.7%) and intersite variability (9.1%) of absolute HER2\\/chromosome enumeration probe 17 ratios were tightly controlled across all participating laboratories. The Ventana HER2 dual-color ISH assay is robust and reproducible, shows good concordance with a standard FISH assay, and complies with requirements in national and international guidelines for performance of ISH-based diagnostic tests.

  1. MQW electroabsorption modulator-integrated DFB laser modules for high-speed transmission

    Science.gov (United States)

    Zhao, Q.; Pan, J. Q.; Zhang, J.; Li, B. X.; Zhou, F.; Wang, B. J.; Wang, L. F.; Zhao, L. J.; Zhou, G. T.; Wang, W.

    2006-06-01

    Details of the design, fabrication and testing of a strained InGaAsP/InGaAsP multiple quantum well (MQW) electroabsorption modulator (EAM) monolithically integrated with a DFB laser by ultra-low-pressure selective area growth (SAG) are presented. The method greatly simplifies the integration process. A study of the controllability of band-gap energy by SAG has been performed. After being completely packaged in a seven-pin butterfly compact module, the device successfully performs 10 Gb s-1 nonreturn to zero (NRZ) operation on uncompensated transmission span >53 km in a standard fibre with a 8.7 dB dynamic extinction ratio. A receiver sensitivity of -18.9 dBm at a bit error rate (BER) of 10-10 is confirmed. 10 GHz short pulse trains with 15.3 ps pulsewidth have also been generated.

  2. Solid-phase single molecule biosensing using dual-color colocalization of fluorescent quantum dot nanoprobes

    Science.gov (United States)

    Liu, Jianbo; Yang, Xiaohai; Wang, Kemin; Wang, Qing; Liu, Wei; Wang, Dong

    2013-10-01

    The development of solid-phase surface-based single molecule imaging technology has attracted significant interest during the past decades. Here we demonstrate a sandwich hybridization method for highly sensitive detection of a single thrombin protein at a solid-phase surface based on the use of dual-color colocalization of fluorescent quantum dot (QD) nanoprobes. Green QD560-modified thrombin binding aptamer I (QD560-TBA I) were deposited on a positive poly(l-lysine) assembled layer, followed by bovine serum albumin blocking. It allowed the thrombin protein to mediate the binding of the easily detectable red QD650-modified thrombin binding aptamer II (QD650-TBA II) to the QD560-TBA I substrate. Thus, the presence of the target thrombin can be determined based on fluorescent colocalization measurements of the nanoassemblies, without target amplification or probe separation. The detection limit of this assay reached 0.8 pM. This fluorescent colocalization assay has enabled single molecule recognition in a separation-free detection format, and can serve as a sensitive biosensing platform that greatly suppresses the nonspecific adsorption false-positive signal. This method can be extended to other areas such as multiplexed immunoassay, single cell analysis, and real time biomolecule interaction studies.The development of solid-phase surface-based single molecule imaging technology has attracted significant interest during the past decades. Here we demonstrate a sandwich hybridization method for highly sensitive detection of a single thrombin protein at a solid-phase surface based on the use of dual-color colocalization of fluorescent quantum dot (QD) nanoprobes. Green QD560-modified thrombin binding aptamer I (QD560-TBA I) were deposited on a positive poly(l-lysine) assembled layer, followed by bovine serum albumin blocking. It allowed the thrombin protein to mediate the binding of the easily detectable red QD650-modified thrombin binding aptamer II (QD650-TBA II) to

  3. Study of Rayleigh-backscattering induced coherence collapse in an asymmetric DFB FL sensor

    Science.gov (United States)

    Liu, Wen; Ma, Lina; Hu, Zhengliang; Feng, Ying; Yang, Huayong

    2016-09-01

    Rayleigh-back scattering induced coherence collapse of an asymmetric distributed feedback fiber laser (DFB FL) sensor is investigated using a composite cavity model. The coherence collapse threshold condition of the asymmetric DFB FL sensor is measured. The DFB FL sensor shows different dynamic behaviors in different pump configurations. According to the asymmetric behavior to the external optical feedback, a novel method to find the actual phase shift position of the asymmetric DFB FL sensor is presented.

  4. Multi-immunoreaction-based dual-color capillary electrophoresis for enhanced diagnostic reliability of thyroid gland disease.

    Science.gov (United States)

    Woo, Nain; Kim, Su-Kang; Kang, Seong Ho

    2017-08-04

    Thyroid-stimulating hormone (TSH) secretion plays a critical role in regulating thyroid gland function and circulating thyroid hormones (i.e., thyroxine (T4) and triiodothyronine (T3)). A novel multi-immunoreaction-based dual-color capillary electrophoresis (CE) technique was investigated in this study to assess its reliability in diagnosing thyroid gland disease via simultaneous detection of TSH, T3, and T4 in a single run of CE. Compared to the conventional immunoreaction technique, multi-immunoreaction of biotinylated streptavidin antibodies increased the selectivity and sensitivity for individual hormones in human blood samples. Dual-color laser-induced fluorescence (LIF) detection-based CE performed in a running buffer of 25mM Na2B4O7-NaOH (pH 9.3) allowed for fast, simultaneous quantitative analysis of three target thyroid hormones using different excited wavelengths within 3.2min. This process had excellent sensitivity and detection limits of 0.05-5.32 fM. The results showed 1000-100,000 times higher detection sensitivity than previous methods. Method validation with enzyme linked immunosorbent assay for application with human blood samples showed that the CE method was not significantly different at the 98% confidence level. Therefore, the developed CE-LIF method has the advantages of high detection sensitivity, faster analysis time, and smaller sample amount compared to the conventional methods The combined multi-immunoreaction and dual-color CE-LIF method should have increased diagnostic reliability for thyroid gland disease compared to conventional methods based on its highly sensitive detection of thyroid hormones using a single injection and high-throughput screening. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. DFB laser based electrical dynamic interrogation for optical fiber sensors

    Science.gov (United States)

    Carvalho, J. P.; Frazão, O.; Baptista, J. M.; Santos, J. L.; Barbero, A. P.

    2012-04-01

    An electrical dynamic interrogation technique previously reported by the authors for long-period grating sensors is now progressed by relying its operation exclusively on the modulation of a DFB Laser. The analysis of the detected first and second harmonic generated by the electrical modulation of the DFB Laser allows generating an optical signal proportional to the LPG spectral shift and resilient to optical power fluctuations along the system. This concept permits attenuating the effect of the 1/f noise of the photodetection, amplification and processing electronics on the sensing head resolution. This technique is employed in a multiplexing sensing scheme that measures refractive index variations.

  6. Characterization of cytoplasmic Gag-gag interactions by dual-color z-scan fluorescence fluctuation spectroscopy.

    Science.gov (United States)

    Fogarty, Keir H; Chen, Yan; Grigsby, Iwen F; Macdonald, Patrick J; Smith, Elizabeth M; Johnson, Jolene L; Rawson, Jonathan M; Mansky, Louis M; Mueller, Joachim D

    2011-03-16

    Fluorescence fluctuation spectroscopy (FFS) quantifies the interactions of fluorescently-labeled proteins inside living cells by brightness analysis. However, the study of cytoplasmic proteins that interact with the plasma membrane is challenging with FFS. If the cytoplasmic section is thinner than the axial size of the observation volume, cytoplasmic and membrane-bound proteins are coexcited, which leads to brightness artifacts. This brightness bias, if not recognized, leads to erroneous interpretation of the data. We have overcome this challenge by introducing dual-color z-scan FFS and the addition of a distinctly colored reference protein. Here, we apply this technique to study the cytoplasmic interactions of the Gag proteins from human immunodeficiency virus type 1 (HIV-1) and human T-lymphotropic virus type 1 (HTLV-1). The Gag protein plays a crucial role in the assembly of retroviruses and is found in both membrane and cytoplasm. Dual-color z-scans demonstrate that brightness artifacts are caused by a dim nonpunctate membrane-bound fraction of Gag. We perform an unbiased brightness characterization of cytoplasmic Gag by avoiding the membrane-bound fraction and reveal previously unknown differences in the behavior of the two retroviral Gag species. HIV-1 Gag exhibits concentration-dependent oligomerization in the cytoplasm, whereas HTLV-1 Gag lacks significant cytoplasmic Gag-Gag interactions. Copyright © 2011 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  7. Dual-color bioluminescent bioreporter for forensic analysis: evidence of androgenic and anti-androgenic activity of illicit drugs.

    Science.gov (United States)

    Cevenini, Luca; Michelini, Elisa; D'Elia, Marcello; Guardigli, Massimo; Roda, Aldo

    2013-01-01

    Bioassays represent promising complementary techniques to conventional analytical approaches used in doping analysis to detect illicit drugs like anabolic-androgenic steroids (AAS). The fact that all AAS share a common mechanism of action via the human androgen receptor (hAR) enables the use of bioassays, relying on the activation of hAR as antidoping screening tools. Previously, we developed a dual-color bioreporter based on yeast cells engineered to express hAR and androgen response elements driving the expression of the bioluminescent (BL) reporter protein Photinus pyralis luciferase. A second reporter protein, the red-emitting luciferase PpyRE8, was introduced in the bioreporter as internal viability control. Here, we report the first forensic application of a straightforward, accurate, and cost-effective bioassay, relying on spectral resolution of the two BL signals, in 96-microwell format. The bioreporter responds to dihydrotestosterone as reference androgen in a concentration-dependent manner from 0.08 to 1,000 nM with intra- and inter-assay variation coefficients of 11.4 % and 13.1 %, respectively. We also demonstrated the suitability of this dual-color bioreporter to assess (anti)-androgenic activity of pure AAS, mixtures of AAS, and other illicit drugs provided by the Scientific Police. Significant anti-androgenic activity was observed in samples labeled as marijuana and hashish, containing Δ(9)-tetrahydrocannabinol as major constituent.

  8. Thermodynamic free-energy minimization for unsupervised fusion of dual-color infrared breast images

    Science.gov (United States)

    Szu, Harold; Miao, Lidan; Qi, Hairong

    2006-04-01

    function [A] may vary from the point tumor to its neighborhood, we could not rely on neighborhood statistics as did in a popular unsupervised independent component analysis (ICA) mathematical statistical method, we instead impose the physics equilibrium condition of the minimum of Helmholtz free-energy, H = E - T °S. In case of the point breast cancer, we can assume the constant ground state energy E ° to be normalized by those benign neighborhood tissue, and then the excited state can be computed by means of Taylor series expansion in terms of the pixel I/O data. We can augment the X-ray mammogram technique with passive IR imaging to reduce the unwanted X-rays during the chemotherapy recovery. When the sequence is animated into a movie, and the recovery dynamics is played backward in time, the movie simulates the cameras' potential for early detection without suffering the PD=0.1 search uncertainty. In summary, we applied two satellite-grade dual-color IR imaging cameras and advanced military (automatic target recognition) ATR spectrum fusion algorithm at the middle wavelength IR (3 - 5μm) and long wavelength IR (8 - 12μm), which are capable to screen malignant tumors proved by the time-reverse fashion of the animated movie experiments. On the contrary, the traditional thermal breast scanning/imaging, known as thermograms over decades, was IR spectrum-blind, and limited to a single night-vision camera and the necessary waiting for the cool down period for taking a second look for change detection suffers too many environmental and personnel variabilities.

  9. DFB fiber laser as source for optical communication systems

    DEFF Research Database (Denmark)

    Varming, Poul; Hübner, Jörg; Kristensen, Martin

    1997-01-01

    The results demonstrate that DFB fiber lasers are an attractive alternative as sources in telecommunication systems. The lasers show excellent long-term stability with very high signal to noise ratio and a reasonable output power, combined with exceptional temperature stability and inherent fiber...

  10. Erbium Doped Fibre Lasers up t 1618 nm for Optical Communication beyond the L-band

    DEFF Research Database (Denmark)

    Kristensen, Martin; Varming, Poul; Jensen, Jesper Bo

    1999-01-01

    Up to a few months ago it was expected theoretically that erbium doped DFB fibre lasers could not be made to operate at wavelengths above the L-band (1570nm-1610nm). This is due to the combination of very low gain and problems with two-photon absorption in the erbium. In addition semiconductor DFB...... lasers are difficult to get beyond the L-band. Therefore no transmission systems have ever been made in this wavelength region despite that low loss transmission should still be possible in standard fibres. With the increasing demand for optical bandwidth it will soon be essential to use the entire low....../s transmission over 80km with such a DFB fibre laser at 1613nm. Only a minor power penalty was observed compared to standard transmission.We also show that the intrinsic properties of the DFB fibre lasers remain very good at these long wavelengths. We even observe a few dB improvement of the noise...

  11. A dual-color far-red to near-infrared firefly luciferin analogue designed for multiparametric bioluminescence imaging.

    Science.gov (United States)

    Jathoul, Amit P; Grounds, Helen; Anderson, James C; Pule, Martin A

    2014-11-24

    Red-shifted bioluminescent emitters allow improved in vivo tissue penetration and signal quantification, and have led to the development of beetle luciferin analogues that elicit red-shifted bioluminescence with firefly luciferase (Fluc). However, unlike natural luciferin, none have been shown to emit different colors with different luciferases. We have synthesized and tested the first dual-color, far-red to near-infrared (nIR) emitting analogue of beetle luciferin, which, akin to natural luciferin, exhibits pH dependent fluorescence spectra and emits bioluminescence of different colors with different engineered Fluc enzymes. Our analogue produces different far-red to nIR emission maxima up to λ(max)=706 nm with different Fluc mutants. This emission is the most red-shifted bioluminescence reported without using a resonance energy transfer acceptor. This improvement should allow tissues to be more effectively probed using multiparametric deep-tissue bioluminescence imaging.

  12. Solution-Grown ZnO Films toward Transparent and Smart Dual-Color Light-Emitting Diode.

    Science.gov (United States)

    Huang, Xiaohu; Zhang, Li; Wang, Shijie; Chi, Dongzhi; Chua, Soo Jin

    2016-06-22

    An individual light-emitting diode (LED) capable of emitting different colors of light under different bias conditions not only allows for compact device integration but also extends the functionality of the LED beyond traditional illumination and display. Herein, we report a color-switchable LED based on solution-grown n-type ZnO on p-GaN/n-GaN heterojunction. The LED emits red light with a peak centered at ∼692 nm and a full width at half-maximum of ∼90 nm under forward bias, while it emits green light under reverse bias. These two lighting colors can be switched repeatedly by reversing the bias polarity. The bias-polarity-switched dual-color LED enables independent control over the lighting color and brightness of each emission with two-terminal operation. The results offer a promising strategy toward transparent, miniaturized, and smart LEDs, which hold great potential in optoelectronics and optical communication.

  13. Three-Dimensional Reconstruction of Nuclear Envelope Architecture Using Dual-Color Metal-Induced Energy Transfer Imaging.

    Science.gov (United States)

    Chizhik, Anna M; Ruhlandt, Daja; Pfaff, Janine; Karedla, Narain; Chizhik, Alexey I; Gregor, Ingo; Kehlenbach, Ralph H; Enderlein, Jörg

    2017-09-20

    The nuclear envelope, comprising the inner and the outer nuclear membrane, separates the nucleus from the cytoplasm and plays a key role in cellular functions. Nuclear pore complexes (NPCs), which are embedded in the nuclear envelope, control transport of macromolecules between the two compartments. Here, using dual-color metal-induced energy transfer (MIET), we determine the axial distance between Lap2β and Nup358 as markers for the inner nuclear membrane and the cytoplasmic side of the NPC, respectively. Using MIET imaging, we reconstruct the 3D profile of the nuclear envelope over the whole basal area, with an axial resolution of a few nanometers. This result demonstrates that optical microscopy can achieve nanometer axial resolution in biological samples and without recourse to complex interferometric approaches.

  14. Tandem electroabsorption modulators integrated with DFB laser by ultra-low-pressure selective-area-growth MOCVD for 10 GHz optical short pulse generation

    Science.gov (United States)

    Zhao, Q.; Pan, J. Q.; Zhang, J.; Zhou, G. T.; Wu, J.; Wang, L. F.; Wang, W.

    2005-08-01

    A novel device of tandem MQW EAMs monolithically integrated with a DFB laser is fabricated by an ultra-low-pressure (22 mbar) selective area growth MOCVD technique. Experimental results exhibit superior device characteristics with low threshold of 19 mA, output light power of 4.5 mW, and over 20 dB extinction ratio when coupled to a single mode fibre. Moreover, over 10 GHz modulation bandwidth is developed with a driving voltage of 2 V. Using this sinusoidal voltage driven integrated device, 10 GHz repetition rate pulse with an actual width of 13.7 ps without any compression elements is obtained.

  15. One Dimensional Polymeric Organic Photonic Crystals for DFB Lasers

    Directory of Open Access Journals (Sweden)

    F. Scotognella

    2008-01-01

    Full Text Available We present a very simple method to realize a one-dimensional photonic crystal (1D PC, consisting of a dye-doped polymeric multilayer. Due to the high photonic density of states at the edges of the photonic band-gap (PBG, a surface emitting distributed feedback (DFB laser is obtained with this structure. Furthermore, the incidence angle dependence of the PBG of the polymeric multilayer is reported.

  16. Simultaneous monitoring of intracellular ATP and oxygen levels in chondrogenic differentiation using a dual-color bioluminescence reporter.

    Science.gov (United States)

    Kwon, Hyuck Joon; Ohmiya, Yoshihiro; Yasuda, Kazunori

    2014-12-01

    A number of assay methods which measure cellular metabolic activity have only measured intracellular ATP levels because it has been speculated that ATP production and oxygen consumption are obligatorily coupled to each other under normal conditions. However, there exist many cases in which ATP production and oxygen consumption are uncoupled. Therefore, measurement of only intracellular ATP levels has a limit for understanding the overall metabolic states during various cellular functions. Here, we report a novel system for simultaneously monitoring intracellular ATP and oxygen levels using a red-emitting Phrixothrix hirtus luciferase (PxRe) and a blue-emitting Renilla luciferase (Rluc). Using this system, we monitored the dynamic changes in both intracellular ATP and oxygen levels during chondrogenesis. We found that the oxygen level oscillated at twice the frequency of ATP in chondrogenesis and the oxygen oscillations have an antiphase mode to the ATP oscillations; we also found an independent mode for the ATP oscillations. This result indicates that both mitochondrial and non-mitochondrial respiration oscillate and thus play a role in chondrogenesis. This dual-color monitoring system is useful for studying metabolic regulations that underlie diverse cellular processes.

  17. Transformation of odor selectivity from projection neurons to single mushroom body neurons mapped with dual-color calcium imaging.

    Science.gov (United States)

    Li, Hao; Li, Yiming; Lei, Zhengchang; Wang, Kaiyu; Guo, Aike

    2013-07-16

    Although the response properties of most neurons are, to a large extent, determined by the presynaptic inputs that they receive, comprehensive functional characterization of the presynaptic inputs of a single neuron remains elusive. Toward this goal, we introduce a dual-color calcium imaging approach that simultaneously monitors the responses of a single postsynaptic neuron together with its presynaptic axon terminal inputs in vivo. As a model system, we applied the strategy to the feed-forward connections from the projection neurons (PNs) to the Kenyon cells (KCs) in the mushroom body of Drosophila and functionally mapped essentially all PN inputs for some of the KCs. We found that the output of single KCs could be well predicted by a linear summation of the PN input signals, indicating that excitatory PN inputs play the major role in generating odor-selective responses in KCs. When odors failed to activate KC output, local calcium transients restricted to individual postsynaptic sites could be observed in the KC dendrites. The response amplitudes of the local transients often correlated linearly with the presynaptic response amplitudes, allowing direct assay of the strength of single synaptic sites. Furthermore, we found a scaling relationship between the total number of PN terminals that a single KC received and the average synaptic strength of these PN-KC synapses. Our strategy provides a unique perspective on the process of information transmission and integration in a model neural circuit and may be broadly applicable for the study of the origin of neuronal response properties.

  18. Optimization of Single- and Dual-Color Immunofluorescence Protocols for Formalin-Fixed, Paraffin-Embedded Archival Tissues.

    Science.gov (United States)

    Kajimura, Junko; Ito, Reiko; Manley, Nancy R; Hale, Laura P

    2016-02-01

    Performance of immunofluorescence staining on archival formalin-fixed paraffin-embedded human tissues is generally not considered to be feasible, primarily due to problems with tissue quality and autofluorescence. We report the development and application of procedures that allowed for the study of a unique archive of thymus tissues derived from autopsies of individuals exposed to atomic bomb radiation in Hiroshima, Japan in 1945. Multiple independent treatments were used to minimize autofluorescence and maximize fluorescent antibody signals. Treatments with NH3/EtOH and Sudan Black B were particularly useful in decreasing autofluorescent moieties present in the tissue. Deconvolution microscopy was used to further enhance the signal-to-noise ratios. Together, these techniques provide high-quality single- and dual-color fluorescent images with low background and high contrast from paraffin blocks of thymus tissue that were prepared up to 60 years ago. The resulting high-quality images allow the application of a variety of image analyses to thymus tissues that previously were not accessible. Whereas the procedures presented remain to be tested for other tissue types and archival conditions, the approach described may facilitate greater utilization of older paraffin block archives for modern immunofluorescence studies.

  19. Dual-color bioluminescence imaging assay using green- and red-emitting beetle luciferases at subcellular resolution.

    Science.gov (United States)

    Yasunaga, Mayu; Nakajima, Yoshihiro; Ohmiya, Yoshihiro

    2014-09-01

    Bioluminescence imaging is widely used to monitor cellular events, including gene expression in vivo and in vitro. Moreover, recent advances in luciferase technology have made possible imaging at the single-cell level. To improve the bioluminescence imaging system, we have developed a dual-color imaging system in which the green-emitting luciferase from a Brazilian click beetle (Emerald Luc, ELuc) and the red-emitting luciferase from a railroad worm (Stable Luciferase Red, SLR) were used as reporters, which were localized to the peroxisome and the nucleus, respectively. We clearly captured simultaneously the subcellular localization of ELuc in the peroxisome and SLR in the nucleus of a single cell using a high-magnification objective lens with 3-min exposure time without binning using a combination of optical filters. Furthermore, to apply this system to quantitative time-lapse imaging, the activation of nuclear factor triggered by tumor necrosis factor α was measured using nuclear-targeted SLR and peroxisome-targeted ELuc as the test and internal control reporters, respectively. We successfully quantified the kinetics of activation of nuclear factor κB using nuclear-targeted SLR and the transcriptional change of the internal control promoter using peroxisome-targeted ELuc simultaneously in a single cell, and showed that the activation kinetics, including activation rate and amplitude, differed among cells. The results demonstrated that this imaging system can visualize the subcellular localization of reporters and track the expressions of two genes simultaneously at subcellular resolution.

  20. Integrated hybrid silicon DFB laser-EAM array using quantum well intermixing.

    Science.gov (United States)

    Jain, Siddharth R; Sysak, Matthew N; Kurczveil, Geza; Bowers, John E

    2011-07-04

    We demonstrate multiple bandgap integration on the hybrid silicon platform using quantum well intermixing. A broadband DFB laser array and a DFB-EAM array are realized on a single chip using four bandgaps defined by ion implantation enhanced disordering. The broadband laser array uses two bandgaps with 17 nm blue shift to compensate for gain roll-off while the integrated DFB-EAMs use the as-grown bandgap for optical gain and a 30 nm blue shifted bandgap for modulation. The multi-channel DFB array includes 13 lasers with >90 nm gain-bandwidth. The transponder includes four DFB-EAMs with 14 dB DC extinction at 4 V bias.

  1. Clinical, cytogenetic and dual-color FISH studies on five cases of myelodysplastic syndrome or acute myeloid leukemia patients with 1;7 translocation

    Institute of Scientific and Technical Information of China (English)

    申咏梅; 薛永权; 李建勇; 潘金兰; 吴亚芳

    2003-01-01

    Objective To study the clinical and cytogenetic characteristics of four patients with myel odysplastic syndrome (MDS) and one with acute myeloid leukemia experiencing t(1; 7).Methods Five patients seen in our hospital from 1992 to 2001 were diagnosed as MDS and acute myelocytic leukemia (AML) according to the French-American-British (FAB) criteria. Chromosomes were prepared using the direct method as well as 24-hou r unstimulated cultures of fresh heparinized bone marrow for each subject, while R-banding was used to analyze karyotypes. Dual-color fluorescence in situ hy bridization (FISH) using SpectrumRed and SpectrumGreen directly labeled chromoso me 1-specific α-satellite DNA probe (red) and chromosome 7- specific α-sat ellite DNA probe (green) was performed for three cases. Results Of the five patients, three had 1;7 translocation due to along history of expos ure to benzene. In three cases, dual-color FISH resulted in three red signals and two green ones, in which one red signal adjoining one green signal in 27.6% , 84% and 18.5% metaphases, respectively. Conclusions Exposure to benzene may be the cause for Chinese MDS and AML patients with t(1;7 ) translocation. The result of dual-color FISH convincingly confirmed that the centromere of the derivative chromosome 7p/1q resulting from 1;7 translocation was made up of centromeres from both chromosomes 1 and 7.

  2. Genetically-encoded yellow fluorescent cAMP indicator with an expanded dynamic range for dual-color imaging.

    Directory of Open Access Journals (Sweden)

    Haruki Odaka

    Full Text Available Cyclic AMP is a ubiquitous second messenger, which mediates many cellular responses mainly initiated by activation of cell surface receptors. Various Förster resonance energy transfer-based ratiometric cAMP indicators have been created for monitoring the spatial and temporal dynamics of cAMP at the single-cell level. However, single fluorescent protein-based cAMP indicators have been poorly developed, with improvement required for dynamic range and brightness. Based on our previous yellow fluorescent protein-based cAMP indicator, Flamindo, we developed an improved yellow fluorescent cAMP indicator named Flamindo2. Flamindo2 has a 2-fold expanded dynamic range and 8-fold increased brightness compared with Flamindo by optimization of linker peptides in the vicinity of the chromophore. We found that fluorescence intensity of Flamindo2 was decreased to 25% in response to cAMP. Live-cell cAMP imaging of the cytosol and nucleus in COS7 cells using Flamindo2 and nlsFlamindo2, respectively, showed that forskolin elevated cAMP levels in each compartment with different kinetics. Furthermore, dual-color imaging of cAMP and Ca2+ with Flamindo2 and a red fluorescent Ca2+ indicator, R-GECO, showed that cAMP and Ca2+ elevation were induced by noradrenaline in single HeLa cells. Our study shows that Flamindo2, which is feasible for multi-color imaging with other intracellular signaling molecules, is useful and is an alternative tool for live-cell imaging of intracellular cAMP dynamics.

  3. Genetically-Encoded Yellow Fluorescent cAMP Indicator with an Expanded Dynamic Range for Dual-Color Imaging

    Science.gov (United States)

    Odaka, Haruki; Arai, Satoshi; Inoue, Takafumi; Kitaguchi, Tetsuya

    2014-01-01

    Cyclic AMP is a ubiquitous second messenger, which mediates many cellular responses mainly initiated by activation of cell surface receptors. Various Förster resonance energy transfer-based ratiometric cAMP indicators have been created for monitoring the spatial and temporal dynamics of cAMP at the single-cell level. However, single fluorescent protein-based cAMP indicators have been poorly developed, with improvement required for dynamic range and brightness. Based on our previous yellow fluorescent protein-based cAMP indicator, Flamindo, we developed an improved yellow fluorescent cAMP indicator named Flamindo2. Flamindo2 has a 2-fold expanded dynamic range and 8-fold increased brightness compared with Flamindo by optimization of linker peptides in the vicinity of the chromophore. We found that fluorescence intensity of Flamindo2 was decreased to 25% in response to cAMP. Live-cell cAMP imaging of the cytosol and nucleus in COS7 cells using Flamindo2 and nlsFlamindo2, respectively, showed that forskolin elevated cAMP levels in each compartment with different kinetics. Furthermore, dual-color imaging of cAMP and Ca2+ with Flamindo2 and a red fluorescent Ca2+ indicator, R-GECO, showed that cAMP and Ca2+ elevation were induced by noradrenaline in single HeLa cells. Our study shows that Flamindo2, which is feasible for multi-color imaging with other intracellular signaling molecules, is useful and is an alternative tool for live-cell imaging of intracellular cAMP dynamics. PMID:24959857

  4. Optical microwave generation using two parallel DFB lasers integrated with Y-branch waveguide coupler

    Institute of Scientific and Technical Information of China (English)

    Xie Hong-Yun; Wang Lu; Zhao Ling-Juan; Zhu Hong-Liang; Wang Wei

    2007-01-01

    A new device of two parallel distributed feedback (DFB) lasers integrated monolithically with Y-branch waveguide coupler was fabricated by means of quantum well intermixing. Optical microwave signal was generated in the Y-branch waveguide coupler through frequency beating of the two laser modes coming from two DFB laser in parallel, which had a small difference in frequency. Continuous rapid tuning of optical microwave signal from 13 to 42 GHz were realized by adjusting independently the driving currents injected into the two DFB lasers.

  5. Detailed study of four-wave mixing in Raman DFB fiber lasers.

    Science.gov (United States)

    Shi, Jindan; Horak, Peter; Alam, Shaif-Ul; Ibsen, Morten

    2014-09-22

    We both experimentally and numerically studied the ultra-compact wavelength conversion by using the four-wave mixing (FWM) process in Raman distributed-feedback (R-DFB) fiber lasers. The R-DFB fiber laser is formed in a 30 cm-long commercially available Ge/Si standard optical fiber. The internal generated R-DFB signal acts as the pump wave for the FWM process and is in the normal dispersion range of the fiber. Utilizing a tunable laser source as a probe wave, FWM frequency conversion up to ~40 THz has been demonstrated with conversion efficiency > -40 dB. The principle of such a wide bandwidth and high conversion efficiency in such a short R-DFB cavity has been theoretically analyzed. The simulation results match well with the experimental data.

  6. The correlation between dual-color chromogenic in situ hybridization and fluorescence in situ hybridization in assessing HER2 gene amplification in breast cancer

    DEFF Research Database (Denmark)

    Pedersen, Marianne; Rasmussen, Birgitte Bruun

    2009-01-01

    obtained by the 2 methods showed excellent correlation (correlation coefficient 0.95). In conclusion, it is possible by dual-color CISH method to demonstrate HER2 genes and chromosome 17 genes, in the same tissue section and reliably assess HER2 status. The CISH method is a very promising alternative...... invasive breast carcinomas, both FISH and CISH detected HER2 amplification in 24 cases and nonamplification was detected in 47 cases. One case showed a discrepancy between FISH and CISH. The concordance between CISH and FISH was found to be almost perfect (98.6%). The correlation between the HER2 ratios...

  7. Monolithic Integration of a DFB Superlattice Laser Using High Energy Ion Implantation

    Science.gov (United States)

    1991-02-13

    Considerations Relative to DFB/DBR Laser Fabrication .... 46 4.0 Materials Evaluation of Multi-Quantum Well/Superlattice Samples Fabricated by Molecular Beam...important to consider the disordering that can occur during annealing and its effects on device performance. 3.7 CONSIDERATIONS RELATIVE TO DFB/DBR LASER ... FABRICATION The structure examined in ts work is to be incorporated in a distributed feedback type laser. The resolution of the selective ion beam

  8. Period-Doubling in 10 GHz Gain-Switched DFB Laser Diode

    Institute of Scientific and Technical Information of China (English)

    WU Jian; QIU Ji-Fang; LIN Jin-Tong

    2007-01-01

    The distinct period doubling behaviour in a 10 GHz gain-switched (GS) DFB laser is experimentally investigatedin frequency domain and in time domain. The period doubling occurs as the frequency of the rf driving signal is close to or higher than the -3 dB cutoff frequency of the DFB laser diode, and the amplitude of the rf driving signal required to achieve period doubling increases linearly with the increasing bias current of the laser diode.

  9. Analog characterization of a Franz-Keldysh electroabsorption modulator monolithically integrated with a DFB laser

    Science.gov (United States)

    Oennegren, Jan; Svedin, Jan; Sahlen, Olof; Jansson, Mats; Alping, Arne G.

    1995-10-01

    Electroabsorption modulators (EA) are attractive components for very high speed digital links (up to 40 Gbit/s). The objective of the present work has been to evaluate the analog performance and use of a Franz Keldysh modulator (FK) monolithically integrated with a DFB laser (DFB/FK-modulator) operating at 1550 nm. This DFB/FK-modulator is a combination of a directly modulated laser diode and an external modulator in one chip. The analog performance is therefore depending on both the modulator bias voltage and DFB-laser bias current. The normal optical output characteristic from an EA-modulator has a strongly nonlinear behavior. The modulator described in this paper shows for low bias voltage and/or high laser current a linear bahavior. This linear behavior is mainly due to the hole pile-up effect at the p/i-interface of the modulator. In digital transmission system this hole pile-up effect is a disadvantage, but in an analog transmission system it can be used to achieve better analog performance. Measurements (and simulations) on the DFB/FK-modulator show that its analog performance competes well with direct modulated FP and DFB lasers, especially if the modulator is biased for optimum analog performance.

  10. Investigation of External Optical Feedback Resistance of IC-DFB and GC-DFB Lasers Using a Very Simple Experimental set-up

    Institute of Scientific and Technical Information of China (English)

    孙长征; 熊兵; 罗毅; 中野义昭

    2003-01-01

    We study the external optical feedback resistance of both index-coupled (IC) and gain-coupled distributed feedback (DFB) lasers using a very simple experimental set-up. Though IC-DFB lasers with large coupling coefficients are found to be less sensitive to external reflection, they suffer from mode instability at high injection level. On the other hand, the introduction of gain-coupling mechanism can significantly improve both the immunity to external optical feedback and the single mode yield of the device.

  11. T20-insensitive HIV-1 from naive patients exhibits high viral fitness in a novel dual-color competition assay on primary cells.

    Science.gov (United States)

    Neumann, Thomas; Hagmann, Isabel; Lohrengel, Sabine; Heil, Marintha L; Derdeyn, Cynthia A; Kräusslich, Hans-Georg; Dittmar, Matthias T

    2005-03-15

    The relationship between sensitivity to antiviral drugs and viral fitness is of paramount importance in understanding the long-term implications of clinical resistance. Here we report the development of a novel recombinant virus assay to study entry inhibitor-resistant HIV variants using a biologically relevant cell type, primary CD4 T-cells. We have modified the replication-competent molecular clone HIV(NL4-3) to express a reporter protein (Renilla luciferase), Green Fluorescent Protein (EGFP), or Red Fluorescent Protein (DsRed2) upon infection, thus allowing quantification of replication. Luciferase-expressing virus was used to evaluate drug sensitivity, while co-infection with viruses carrying the green and red fluorescent proteins was employed in the competitive fitness assay. Using envelope proteins from three T20 insensitive variants, lower levels of resistance were observed in primary CD4 T-cells than had been previously reported for cell lines. Importantly, dual-color competition assays demonstrated comparable or higher fitness for these variants despite their reduced T20 sensitivity. We conclude that reduced sensitivity to T20 is compatible with high viral fitness in the absence of selection pressure. Thus, simultaneously measuring both resistance and viral fitness using this newly described dual-color competition assay will likely provide important information about resistant viral variants that emerge during therapy with entry inhibitors.

  12. Long-term dual-color tracking of genomic loci by modified sgRNAs of the CRISPR/Cas9 system.

    Science.gov (United States)

    Shao, Shipeng; Zhang, Weiwei; Hu, Huan; Xue, Boxin; Qin, Jinshan; Sun, Chaoying; Sun, Yuao; Wei, Wensheng; Sun, Yujie

    2016-05-19

    Visualization of chromosomal dynamics is important for understanding many fundamental intra-nuclear processes. Efficient and reliable live-cell multicolor labeling of chromosomal loci can realize this goal. However, the current methods are constrained mainly by insufficient labeling throughput, efficiency, flexibility as well as photostability. Here we have developed a new approach to realize dual-color chromosomal loci imaging based on a modified single-guide RNA (sgRNA) of the CRISPR/Cas9 system. The modification of sgRNA was optimized by structure-guided engineering of the original sgRNA, consisting of RNA aptamer insertions that bind fluorescent protein-tagged effectors. By labeling and tracking telomeres, centromeres and genomic loci, we demonstrate that the new approach is easy to implement and enables robust dual-color imaging of genomic elements. Importantly, our data also indicate that the fast exchange rate of RNA aptamer binding effectors makes our sgRNA-based labeling method much more tolerant to photobleaching than the Cas9-based labeling method. This is crucial for continuous, long-term tracking of chromosomal dynamics. Lastly, as our method is complementary to other live-cell genomic labeling systems, it is therefore possible to combine them into a plentiful palette for the study of native chromatin organization and genome ultrastructure dynamics in living cells.

  13. Imaging of gaseous oxygen through DFB laser illumination

    Science.gov (United States)

    Cocola, L.; Fedel, M.; Tondello, G.; Poletto, L.

    2016-05-01

    A Tunable Diode Laser Absorption Spectroscopy setup with Wavelength Modulation has been used together with a synchronous sampling imaging sensor to obtain two-dimensional transmission-mode images of oxygen content. Modulated laser light from a 760nm DFB source has been used to illuminate a scene from the back while image frames were acquired with a high dynamic range camera. Thanks to synchronous timing between the imaging device and laser light modulation, the traditional lock-in approach used in Wavelength Modulation Spectroscopy was replaced by image processing techniques, and many scanning periods were averaged together to allow resolution of small intensity variation over the already weak absorption signals from oxygen absorption band. After proper binning and filtering, the time-domain waveform obtained from each pixel in a set of frames representing the wavelength scan was used as the single detector signal in a traditional TDLAS-WMS setup, and so processed through a software defined digital lock-in demodulation and a second harmonic signal fitting routine. In this way the WMS artifacts of a gas absorption feature were obtained from each pixel together with intensity normalization parameter, allowing a reconstruction of oxygen distribution in a two-dimensional scene regardless from broadband transmitted intensity. As a first demonstration of the effectiveness of this setup, oxygen absorption images of similar containers filled with either oxygen or nitrogen were acquired and processed.

  14. Low Power Consumption Substrate-Emitting DFB Quantum Cascade Lasers.

    Science.gov (United States)

    Liu, Chuan-Wei; Zhang, Jin-Chuan; Jia, Zhi-Wei; Zhuo, Ning; Zhai, Shen-Qiang; Wang, Li-Jun; Liu, Jun-Qi; Liu, Shu-Man; Liu, Feng-Qi; Wang, Zhan-Guo

    2017-09-02

    In the present work, an ultra-low power consumption substrate-emitting distributed feedback (DFB) quantum cascade laser (QCL) was developed. The continuous-wave (CW) threshold power dissipation is reduced to 0.43 W at 25 °C by shortening the cavity length to 0.5 mm and depositing high-reflectivity (HR) coating on both facets. As far as we know, this is the recorded threshold power dissipation of QCLs in the same conditions. Single-mode emission was achieved by employing a buried second-order grating. Mode-hop free emission can be observed within a wide temperature range from 15 to 105 °C in CW mode. The divergence angles are 22.5(o) and 1.94(o) in the ridge-width direction and cavity-length direction, respectively. The maximum optical power in CW operation was 2.4 mW at 25 °C, which is sufficient to spectroscopy applications.

  15. Fully characterization of an active optical filter based on an equivalent-phase-shifted DFB-SOA

    Science.gov (United States)

    Deng, Ye; Li, Ming; Shi, Nuannuan; Tang, Jian; Sun, Shuqian; Zhang, Lihong; Li, Wei; Zhu, Ninghua

    2016-10-01

    A fully characterization of an active optical filter based on an equivalent-phase-shifted DFB-SOA has been theoretically analyzed and experimentally demonstrated in this paper. By employing an optical vector network analyzer (OVNA), transmission characteristics of the equivalent-phase-shifted DFB-SOA are obtained. The influences of driven current on transmission characteristics of the equivalent-phase-shifted DFB-SOA are also investigated. In addition to the advantage of integration, the proposed equivalent-phase-shifted DFB-SOA also shows significant application in design of photonic devices for all-optical signal processing and computing.

  16. Non-resonant wavelength modulation saturation spectroscopy in acetylene-filled hollow-core photonic bandgap fibres applied to modulation-free laser diode stabilisation.

    Science.gov (United States)

    Pineda-Vadillo, Pablo; Lynch, Michael; Charlton, Christy; Donegan, John F; Weldon, Vincent

    2009-12-07

    In this paper the application of Wavelength Modulation (WM) techniques to non-resonant saturation spectroscopy in acetylene-filled Hollow-Core Photonic Bandgap Fibres (HC-PBFs) and modulation-free Laser Diode (LD) frequency stabilisation is investigated. In the first part WM techniques are applied to non-resonant pump-probe saturation of acetylene overtone rotational transitions in a HC-PBF. A high-power DFB chip-on-carrier mounted LD is used in conjunction with a tuneable External Cavity Laser (ECL) and the main saturation parameters are characterized. In the second part a novel feedback system to stabilize the DFB emission wavelength based on the WM saturation results is implemented. Modulation-free locking of the DFB laser frequency to the narrow linewidth saturation feature is achieved for both constant and variable LD temperatures.

  17. High accuracy wavelength locking of a DFB laser using tunable polarization interference filter

    Institute of Scientific and Technical Information of China (English)

    Xiyao Chen(陈曦曜); Jianping Xie(谢建平); Tianpeng Zhao(赵天鹏); Hai Ming(明海); Anting Wang(王安廷); Wencai Huang(黄文财); Liang Lü(吕亮); Lixin Xu(许立新)

    2003-01-01

    A temperature-tunable polarization interference filter (PIF) made of YVO4 crystal has been presented and applied for wavelength locking of a distributed feedback (DFB) semiconductor laser in dense wavelength-division-multiplexing (DWDM) optical communication systems. This new design offers a flexible way to monitor and then lock an operating wavelength of DFB laser to any preselected point without dead spots.The results show that the laser wavelength can be locked with accuracy better than ±0.01 nm with much relaxed requirement on temperature stability of the filter.

  18. A DFB Fiber Laser Sensor System with Ultra-High Resolution and Its Noise Analysis

    Institute of Scientific and Technical Information of China (English)

    Hao Xiao; Fang Li; Jun He; Yu-Liang Liu

    2008-01-01

    A distributed feedback fiber laser (DFB FL) sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs an unbalanced Michelson interferometer to translate laser wavelength shifts induced by weak measurands into phase shifts. A digital phase generated carrier demodulation scheme is introduced to achieve ultra-high resolution interrogation. A detailed noise analysis of the system is presented, and it is shown that the system resolution is limited by the frequency noise of the DFB FL.

  19. Design and performance of a complex-coupled DFB laser with sampled grating

    Institute of Scientific and Technical Information of China (English)

    王桓; 朱洪亮; 贾凌慧; 陈向飞; 王圩

    2009-01-01

    A complex-coupled DFB laser with sampled grating has been designed and fabricated. The method uses the + 1 st order reflection of the sampled grating for laser single-mode operation. The typical threshold current of the sampled grating based DFB laser is 25 mA, and the optical output is about 10 mW at the injected current of 100 mA. The lasing wavelength of the device is 1.5385μm, which is the +1 st order wavelength of the sampled grating.

  20. Performance Evaluation for DFB and VCSEL-based 60 GHz Radio-over-Fiber System

    DEFF Research Database (Denmark)

    Pang, Xiaodan; Lebedev, Alexander; Vegas Olmos, Juan José

    2013-01-01

    In this paper, we report on a detailed analysis and performance comparison work between 60 GHz radio-over-fiber systems based on a DFB laser and a C-band VCSEL. Coherent photonic up-conversion method is applied for the 60 GHz millimeter-wave signal generation. The generated signals are evaluated...... by means of phase noise and bit error rate for different transmission scenarios. The results show a positive potential to adopt both DFB lasers and VCSELs for the next generation 60 GHz hybrid fiber-wireless access networks....

  1. Modulation characteristics of tunable DFB/DBR lasers with one or two passive tuning sections

    DEFF Research Database (Denmark)

    Pan, Xing; Olesen, Henning; Tromborg, Bjarne

    1989-01-01

    Calculation of the small-signal modulation characteristics of tunable distributed-feedback (DFB) and distributed Bragg reflector (DBR) lasers requires rate equations for the photon number, the phase of the electric field, and the carrier densities. Here, the rate equation for the photon number...

  2. Stable CW Single-Mode Photonic Crystal Fiber DFB Ring Laser

    Institute of Scientific and Technical Information of China (English)

    Kevin Cook; John Canning; John Holdsworth; Chris Dewhurst

    2008-01-01

    We demonstrate stable single-mode CW operation of a DFB ring laser based on Er3+ doped photonics crystal fiber (PCF). The incorporation of a ring cavity allows one single mode to lase and also suppresses the unwanted effect of self-pulsing. Such a narrow linewidth source in PCF has great potential in spectroscopy.

  3. A double wavelength DFB laser with an identical active area for CWDM

    Institute of Scientific and Technical Information of China (English)

    Hongyun Xie; Wei Wang; Fan Zhou; Jing Bian; Baojun Wang; Lufeng Wang

    2005-01-01

    A novel distribute feedback (DFB) laser which gave two different wavelengths under two distinct work conditions was fabricated. The laser consists of two Bragg gratings with different periods corresponding to wavelength spacing of 20 nm in an identical active area. When driving current was injected into one of the different sections separately, two different wavelengths at 1542.4 and 1562.5 nm were realized. The side mode suppression ratio (SMSR) of 45 dB or more both for the two Bragg wavelengths were achieved. The fabricating process of the laser was just the same as that of traditional DFB laser diode. This device can be potentially used in coarse wavelength division multiplexer (CWDM) as a promising light source and the technology idea can be used to enlarge the transmission capacity in metro area network (MAN).

  4. Study of multiwavelength DFB semiconductor laser array with asymmetric structures based on sampling technique.

    Science.gov (United States)

    Shi, Yuechun; Cao, Baoli; Li, Lianyan; Tang, Song; Zheng, Junshou; Zhang, Peng; Chen, Ting; Liu, Shengchun

    2014-10-10

    Multiwavelength distributed feedback (DFB) semiconductor laser arrays (MLA) with asymmetric structures are studied in this paper. Thanks to the sampling technique, the asymmetric structures, including asymmetric phase shift and asymmetric coupling coefficient, can be achieved by common holographic exposure. Therefore, the cost of fabrication is remarkably reduced. In addition, due to the large scale of the sampling pattern, the wavelength precision of these kinds of MLA can be simultaneously improved. As an example, we designed and fabricated an asymmetrically phase-shifted MLA with 10 wavelengths for the first time. Compared with the common phase-shifted DFB laser, slope efficiency is significantly improved and single longitudinal mode is still guaranteed. Besides, relatively high wavelength precision is also obtained. The proposed MLA configurations may significantly benefit multiwavelength emitters for future photonic integration.

  5. Numerical Analysis of SHB Effects in Laterally-Coupled Distributed Feedback (LC-DFB Lasers

    Directory of Open Access Journals (Sweden)

    M. Seifouri

    2012-10-01

    Full Text Available In this paper the stability of Laterally-Coupled Distributed Feedback (LC-DFB Lasers against the Spatial Hole Burning (SHB effect is analyzed theoretically. The stability of the laser structure is evaluated using the flatness parameter F. It is shown that the LC-DFB lasers are stable in a wide range of different values ​​of ridge width and amplitude grating. The stability is sustained with increasing injection current. The results show that the flatness parameter is minimal for certain values ​​of the amplitude grating. The numerical calculations have been done by coupled wave and carrier rate equations on the basis of the transfer matrix method (TMM.

  6. Packaging and testing of multi-wavelength DFB laser array using REC technology

    Science.gov (United States)

    Ni, Yi; Kong, Xuan; Gu, Xiaofeng; Chen, Xiangfei; Zheng, Guanghui; Luan, Jia

    2014-02-01

    Packaging of distributed feedback (DFB) laser array based on reconstruction-equivalent-chirp (REC) technology is a bridge from chip to system, and influences the practical process of REC chip. In this paper, DFB laser arrays of 4-channel @1310 nm and 8-channel @1550 nm are packaged. Our experimental results show that both these laser arrays have uniform wavelength spacing and larger than 35 dB average Side Mode Suppression Ratio (SMSR). When I=35 mA, we obtain the total output power of 1 mW for 4-channel @1310 nm, and 227 μw for 8-channel @1550 nm respectively. The high frequency characteristics of the packaged chips are also obtained, and the requirements for 4×10 G or even 8×10 G systems can be reached. Our results demonstrate the practical and low cost performance of REC technology and indicate its potential in the future fiber-to-the-home (FTTH) application.

  7. Integrated DFB-DBR laser modulator grown by selective area metalorganic vapor phase epitaxy growth technique

    Science.gov (United States)

    Tanbun-Ek, T.; Chen, Y. K.; Grenko, J. A.; Byrne, E. K.; Johnson, J. E.; Logan, R. A.; Tate, A.; Sergent, A. M.; Wecht, K. W.; Sciortine, P. F.; Chu, S. N. G.

    1994-12-01

    A device quality of selective epitaxy growth of InGaAsP/InP multiple quantum well (MQW) structure using low-pressure metalorganic vapor phase epitaxy (MOVPE) technique is described. The technique is applied to a monolithically integrated electroabsorption modulator with distributed feedback (DFB) and distributed Bragg reflector (DBR) lasers. Superior device characteristics such as efficient modulation, low threshold current and high efficiency operation of the integrated devices are obtained.

  8. Integrated electroabsorption-modulated DFB laser by using an improved butt-joint method

    Institute of Scientific and Technical Information of China (English)

    Baoxia Li(李宝霞); Xiaohua Hu(胡小华); Hongliang Zhu(朱洪亮); Baojun Wang(王宝军); Lingjuan Zhao(赵玲娟); Wei Wang(王圩)

    2004-01-01

    An improved butt coupling method is used to fabricate an electroabsorption modulator (EAM) monolithically integrated with a distributed feedback (DFB) laser. The obtained electroabsorption-modulated laser (EML) chip with the traditional shallow ridge exhibits very low threshold current of 12 mA, output power of more than 8 mW, and static extinction ratio of -7 dB at the applied bias voltage from 0.5 to -2.0 V.

  9. DBR and DFB Lasers in Neodymium- and Ytterbium-Doped Photothermorefractive Glasses

    Science.gov (United States)

    Ryasnyanskiy, Aleksandr; Vorobiev, N.; Smirnov, V.; Lumeau, J.; Glebov, A.; Mokhun, O..; Spiegelberg, Ch.; Krainak, Michael A.; Glebov, A.; Glebov, L.

    2014-01-01

    The first demonstration, to the best of our knowledge, of distributed Bragg reflector (DBR) and monolithic distributed feedback (DFB) lasers in photothermorefractive glass doped with rare-earth ions is reported. The lasers were produced by incorporation of the volume Bragg gratings into the laser gain elements. A monolithic single-frequency solid-state laser with a line width of 250 kHz and output power of 150 mW at 1066 nm is demonstrated.

  10. Integrated electroabsorption-modulated DFB laser by using an improved butt-joint method

    Science.gov (United States)

    Li, Baoxia; Hu, Xiaohua; Zhu, Hongliang; Wang, Baojun; Zhao, Lingjuan; Wang, Wei

    2004-04-01

    An improved butt coupling method is used to fabricate an electroabsorption modulator (EAM) monolithically integrated with a distributed feedback (DFB) laser. The obtained electroabsorption-modulated laser (EML) chip with the traditional shallow ridge exhibits very low threshold current of 12 mA, output power of more than 8 mW, and static extinction ratio of -7 dB at the applied bias voltage from 0.5 to -2.0 V.

  11. 20 Gbit/s transmission experiments using an integrated MQW modulator/DFB laser module

    Science.gov (United States)

    Kataoka, T.; Miyamoto, Y.; Hagimoto, K.; Sato, K.; Kotaka, I.; Wakita, K.

    1994-05-01

    An integrated MQW electroabsorption modulator/DFB laser module that operates at 2V was developed. It offers a 22dB extinction ratio and 15GHz bandwidth. 100km transmission experiments at 20 Gbit/s are carried out using a prototype module. To the best of the authors' knowledge, this is the first report where 20 Gbit/s transmission has been achieved with a monolithically integrated light source.

  12. Fibre-Optic Gyroscope

    Directory of Open Access Journals (Sweden)

    V. N. Saxena

    1983-04-01

    Full Text Available Comparative study of mechanical, ring-laser and fibre-optic gyroscopes has been made. The single mode fibre-optic gyroscope having a large number of turns of the optical fibre in the spool, replacing He-Ne gas laser by a GaAs laser diode, there by reducing the noise level, and using fully integrated fibre-optics, works out to be the best in the final analysis, for safe navigation and homing of the guided missiles.

  13. Re-evaluation of all-plastic organic dye laser with DFB structure fabricated using photoresists

    Science.gov (United States)

    Tsutsumi, Naoto; Nagi, Saori; Kinashi, Kenji; Sakai, Wataru

    2016-10-01

    Organic solid-state lasers (OSSLs) with distributed feedback structures can detect nanoscale materials and therefore offer an attractive sensing platform for biological and medical applications. Here we investigate the lasing characteristics, i.e., the threshold and slope efficiency, as a function of the grating depth in OSSL devices with distributed feedback (DFB) structure fabricated using photoresists. Two types of photoresists were used for the DFB structures: a negative photoresist, SU-8 2002, and a positive photoresist, ma-P 1275. The DFB structure was fabricated using a Lloyd-mirror configuration. The active layer was a rhodamine 6G-doped cellulose acetate waveguide. The threshold for the first order mode (m  = 1) was lower than that for the second and third order modes (m = 2, and 3). A low threshold of 27 μJ cm-2 pulse-1 (58 nJ) was obtained using SU-8 2002, with m = 1. The slope efficiency was evaluated as a function of grating depth for each mode and increased as the grating depth increased.

  14. Spectroscopic benzene detection using a broadband monolithic DFB-QCL array

    Science.gov (United States)

    Lewicki, Rafał; Witinski, Mark; Li, Biao; Wysocki, Gerard

    2016-03-01

    Quantitative laser spectroscopic measurements of complex molecules that have a broad absorption spectra require broadly tunable laser sources operating preferably in the mid-infrared molecular fingerprint region. In this paper a novel broadband mid-infrared laser source comprising of an array of single-mode distributed feedback quantum cascade lasers was used to target a broadband absorption feature of benzene (C6H6), a toxic and carcinogenic atmospheric pollutant. The DFB-QCL array is a monolithic semiconductor device with no opto-mechanical components, which eliminates issues with mechanical vibrations. The DFB-QCLs array used in this work provides spectral coverage from 1022.5 cm-1 to 1053.3 cm-1, which is sufficient to access the absorption feature of benzene at 1038 cm-1 (9.64 μm). A sensor prototype based on a 76 m multipass cell (AMAC-76LW, Aerodyne Research) and a dispersive DFB-QCL array beam combiner was developed and tested. The Allan deviation analysis of the retrieved benzene concentration data yields a short-term precision of 100 ppbv/Hz1/2 and a minimum detectable concentration of 12 ppbv for 200 s averaging time. The system was also tested by sampling atmospheric air as well as vapors of different chemical products that contained traces of benzene.

  15. High Efficiency, Low Power-Consumption DFB Quantum Cascade Lasers Without Lateral Regrowth.

    Science.gov (United States)

    Jia, Zhi-Wei; Wang, Li-Jun; Zhang, Jin-Chuan; Liu, Feng-Qi; Zhou, Yu-Hong; Wang, Dong-Bo; Jia, Xue-Feng; Zhuo, Ning; Liu, Jun-Qi; Zhai, Shen-Qiang; Wang, Zhan-Guo

    2017-12-01

    Very low power-consumption distributed feedback (DFB) quantum cascade lasers (QCLs) at the wavelength around 4.9 μm were fabricated by conventional process without lateral regrowth of InP:Fe or using sidewall grating. Benefitted from the optimized materials and low waveguide loss, very low threshold current density of 0.5 kA/cm(2) was obtained for a device with cavity length of 2 mm. Combined with the partial-high-reflection coating, the 1-mm-long DFB QCL achieved low power-consumption continuous wave (CW) operation up to 105 °C. The CW threshold power-consumptions were 0.72 and 0.78 W at 15 and 25 °C, respectively. The maximum CW output power was over 110 mW at 15 °C and still more than 35 mW at 105 °C. At 15 °C, wall-plug efficiency of 5.5% and slope efficiency of 1.8 W/A were deduced, which were very high for low power-consumption DFB QCLs.

  16. Dual-color reporter switching system to discern dimer formations of G-protein-coupled receptors using Cre/loxP site-specific recombination in yeast.

    Science.gov (United States)

    Nakamura, Yasuyuki; Hashimoto, Takamichi; Ishii, Jun; Kondo, Akihiko

    2016-10-01

    G-protein-coupled receptors (GPCRs) are physiologically important membrane proteins that represent major molecular targets in pharmaceutical and medicinal fields. Many GPCRs have been shown to form not only homodimers, but also heterodimers that can confer large functional and physiological diversity and are therefore expected to offer new opportunities for the discovery of new drugs. Yeast is a useful host organism that can be used to investigate the interactions between eukaryotic protein pairs, as demonstrated by the yeast two-hybrid (Y2H) system. Previously, we established reporter gene assay systems to screen for GPCR dimer pairs based on the split-ubiquitin membrane Y2H (mY2H) system. However, conventional systems only induce reporter gene expressions from the OFF to ON states. In this study, we therefore designed a reporter switching system that can switch the expressions between two reporter genes (one from ON to OFF and the other from OFF to ON) in response to the Y2H readout. To invoke reporter switching, we took advantage of Cre/loxP site-specific recombination. Through optimization of Cre-mediated reporter gene recombination using the split-ubiquitin mY2H system, we built a dual-color reporter switching system to discern the formations of GPCR dimers. This system enabled monitoring of the formations of homodimers and heterodimers of human serotonin 1A receptor or β2 -adrenergic receptor as well as homodimers of the yeast endogenous pheromone receptor (Ste2p) in yeast cells. Our reporter switching system may be a useful tool for identifying potential molecular targets among GPCR dimers, and is also applicable to other reporter gene assay systems. Biotechnol. Bioeng. 2016;113: 2178-2190. © 2016 Wiley Periodicals, Inc.

  17. Dual-color fluorescence in situ hybridization reveals an association of chromosome 8q22 but not 8p21 imbalance with high grade invasive breast carcinoma.

    Science.gov (United States)

    Walker, Logan C; McDonald, Margaret; Wells, J Elisabeth; Harris, Gavin C; Robinson, Bridget A; Morris, Christine M

    2013-01-01

    We previously reported molecular karyotype analysis of invasive breast tumour core needle biopsies by comparative genomic hybridization (CGH) and fluorescence in situ hybridization (FISH) (Walker et al, Genes Chromosomes Cancer, 2008 May;47(5):405-17). That study identified frequently recurring gains and losses involving chromosome bands 8q22 and 8p21, respectively. Moreover, these data highlighted an association between 8q22 gain and typically aggressive grade 3 tumors. Here we validate and extend our previous investigations through FISH analysis of tumor touch imprints prepared from excised breast tumor specimens. Compared to post-surgical tumor excisions, core needle biopsies are known to be histologically less precise when predicting tumor grade. Therefore investigating these chromosomal aberrations in tumor samples that offer more reliable pathological assessment is likely to give a better overall indication of association. A series of 60 breast tumors were screened for genomic copy number changes at 8q22 and 8p21 by dual-color FISH. Results confirm previous findings that 8p loss (39%) and 8q gain (74%) occur frequently in invasive breast cancer. Both absolute quantification of 8q22 gain across the sample cohort, and a separate relative assessment by 8q22:8p21 copy number ratio, showed that the incidence of 8q22 gain significantly increased with grade (p = 0.004, absolute and p = 0.02, relative). In contrast, no association was found between 8p21 loss and tumor grade. These findings support the notion that 8q22 is a region of interest for invasive breast cancer pathogenesis, potentially harboring one or more genes that, when amplified, precipitate the molecular events that define high tumor grade.

  18. Dual-color fluorescence in situ hybridization reveals an association of chromosome 8q22 but not 8p21 imbalance with high grade invasive breast carcinoma.

    Directory of Open Access Journals (Sweden)

    Logan C Walker

    Full Text Available We previously reported molecular karyotype analysis of invasive breast tumour core needle biopsies by comparative genomic hybridization (CGH and fluorescence in situ hybridization (FISH (Walker et al, Genes Chromosomes Cancer, 2008 May;47(5:405-17. That study identified frequently recurring gains and losses involving chromosome bands 8q22 and 8p21, respectively. Moreover, these data highlighted an association between 8q22 gain and typically aggressive grade 3 tumors. Here we validate and extend our previous investigations through FISH analysis of tumor touch imprints prepared from excised breast tumor specimens. Compared to post-surgical tumor excisions, core needle biopsies are known to be histologically less precise when predicting tumor grade. Therefore investigating these chromosomal aberrations in tumor samples that offer more reliable pathological assessment is likely to give a better overall indication of association. A series of 60 breast tumors were screened for genomic copy number changes at 8q22 and 8p21 by dual-color FISH. Results confirm previous findings that 8p loss (39% and 8q gain (74% occur frequently in invasive breast cancer. Both absolute quantification of 8q22 gain across the sample cohort, and a separate relative assessment by 8q22:8p21 copy number ratio, showed that the incidence of 8q22 gain significantly increased with grade (p = 0.004, absolute and p = 0.02, relative. In contrast, no association was found between 8p21 loss and tumor grade. These findings support the notion that 8q22 is a region of interest for invasive breast cancer pathogenesis, potentially harboring one or more genes that, when amplified, precipitate the molecular events that define high tumor grade.

  19. Dual-Color Bioluminescence Imaging for Simultaneous Monitoring of the Intestinal Persistence of Lactobacillus plantarum and Lactococcus lactis in Living Mice.

    Science.gov (United States)

    Daniel, Catherine; Poiret, Sabine; Dennin, Véronique; Boutillier, Denise; Lacorre, Delphine Armelle; Foligné, Benoit; Pot, Bruno

    2015-08-15

    Lactic acid bacteria are found in the gastrointestinal tract of mammals and have received tremendous attention due to their health-promoting properties. We report the development of two dual-color luciferase-producing Lactobacillus (Lb.) plantarum and Lactococcus (Lc.) lactis strains for noninvasive simultaneous tracking in the mouse gastrointestinal tract. We previously described the functional expression of the red luciferase mutant (CBRluc) from Pyrophorus plagiophthalamus in Lb. plantarum NCIMB8826 and Lc. lactis MG1363 (C. Daniel, S. Poiret, V. Dennin, D. Boutillier, and B. Pot, Appl Environ Microbiol 79:1086-1094, 2013, http://dx.doi.org/10.1128/AEM.03221-12). In this study, we determined that CBRluc is a better-performing luciferase for in vivo localization of both lactic acid bacteria after oral administration than the green click beetle luciferase mutant construct developed in this study. We further established the possibility to simultaneously detect red- and green-emitting lactic acid bacteria by dual-wavelength bioluminescence imaging in combination with spectral unmixing. The difference in spectra of light emission by the red and green click beetle luciferase mutants and dual bioluminescence detection allowed in vitro and in vivo quantification of the red and green emitted signals; thus, it allowed us to monitor the dynamics and fate of the two bacterial populations simultaneously. Persistence and viability of both strains simultaneously administered to mice in different ratios was studied in vivo in anesthetized mice and ex vivo in mouse feces. The application of dual-luciferase-labeled bacteria has considerable potential to simultaneously study the interactions and potential competitions of different targeted bacteria and their hosts.

  20. Effect of Core/Shell Interface on Carrier Dynamics and Optical Gain Properties of Dual-Color Emitting CdSe/CdS Nanocrystals.

    Science.gov (United States)

    Pinchetti, Valerio; Meinardi, Francesco; Camellini, Andrea; Sirigu, Gianluca; Christodoulou, Sotirios; Bae, Wan Ki; De Donato, Francesco; Manna, Liberato; Zavelani-Rossi, Margherita; Moreels, Iwan; Klimov, Victor I; Brovelli, Sergio

    2016-07-26

    Two-color emitting colloidal semiconductor nanocrystals (NCs) are of interest for applications in multimodal imaging, sensing, lighting, and integrated photonics. Dual color emission from core- and shell-related optical transitions has been recently obtained using so-called dot-in-bulk (DiB) CdSe/CdS NCs comprising a quantum-confined CdSe core embedded into an ultrathick (∼7-9 nm) CdS shell. The physical mechanism underlying this behavior is still under debate. While a large shell volume appears to be a necessary condition for dual emission, comparison between various types of thick-shell CdSe/CdS NCs indicates a critical role of the interface "sharpness" and the presence of potential barriers. To elucidate the effect of the interface morphology on the dual emission, we perform side-by-side studies of CdSe/CdS DiB-NCs with nominally identical core and shell dimensions but different structural properties of the core/shell interface arising from the crystal structure of the starting CdSe cores (zincblende vs wurtzite). While both structures exhibit dual emission under comparable pump intensities, NCs with a zincblende core show a faster growth of shell luminescence with excitation fluence and a more readily realized regime of amplified spontaneous emission (ASE) even under "slow" nanosecond excitation. These distinctions can be linked to the structure of the core/shell interface: NCs grown from the zincblende cores contain a ∼3.5 nm thick zincblende CdS interlayer, which separates the core from the wurtzite CdS shell and creates a potential barrier for photoexcited shell holes inhibiting their relaxation into the core. This helps maintain a higher population of shell states and simplifies the realization of dual emission and ASE involving shell-based optical transitions.

  1. Development of an advanced uncooled 10-Gb DFB laser for volume manufacture

    Science.gov (United States)

    Burns, Gordon; Charles, Paul M.

    2003-03-01

    Optical communication systems operating at 10Gbit/s such as 10Gigabit Ethernet are becoming more and more important in Local Area Networks (LAN) and Metropolitan Area Networks (MAN). This market requires optical transceivers of low cost, size and power consumption. This drives a need for uncooled DFB lasers directly modulated at 10Gbit/s. This paper describes the development of a state of the art uncooled high speed DFB laser which is capable of being manufactured in high volume at the low cost demanded by the GbE market. A DFB laser was designed by developing technological building blocks within the 'conventional" InGaAsP materials system, using existing well proven manufacturing processes modules wherever possible, limiting the design risk to a few key areas where innovation was required. The temperature and speed performance of the InGaAsP SMQW active layer system was carefully optimized and then coupled with a low parasitic lateral confinement system. Using concurrent engineering, new processes were demonstrated to have acceptable process capability within a manufacturing fabrication environment, proving their ability to support high volume manufacturing requirements. The DFB laser fabricated was shown to operate at 100C chip temperature with an open eye at 10Gbit/s operation (with an extinction ratio >5dB). Up to 90C operation this DFB shows threshold current as low as 29mA, optical power as high as 13mW and it meets the 10Gb scaled Ethernet mask with extinction ratio >6dB. It was found that the high temperature dynamic behavior of these lasers could not be fully predicted from static test data. A production test strategy was therefore followed where equipment was designed to fully test devices/subassemblies at 100C and up to 20Gbit/s at key points in the product build. This facilitated the rapid optimisation of product yields upon manufacturing ramp up and minimization of product costs. This state of the art laser is now transferred into volume manufacture.

  2. Microstructured polymer optical fibres

    CERN Document Server

    Large, Maryanne; Barton, Geoff; van Eijkelenborg, Martijn A

    2008-01-01

    Microstructured Polymer Optical Fibres describes the optical properties of microstructured fibres, how they are made and modelled, and outlines some potential applications. These applications include areas where polymer fibres are already used, such as high-data rate transmission for Fibre-to-the Home or within cars, as well as completely new areas such as the photonic bandgap transmission of ""difficult"" wavelengths. Emphasising a conceptual understanding of the underlying physics, Microstructured Polymer Optical Fibres is clearly written, and includes numerous illustrations. It provides an

  3. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end......-directional arrangement. The fibre illumination system comprises a fibre illumination module of the above-mentioned type. By the invention, daylight may be exploited for the illumination of remote interior spaces of buildings in order to save energy, and improve the well-being of users in both housing and working...

  4. Deep surface grating DFB and DBR quantum well diode lasers in AlGaAs/GaAs for photonic integration

    Science.gov (United States)

    Ayling, Stephen G.; Moreira, M. V.; Abe, H.; Bryce, A. Catrina; De La Rue, Richard M.; Marsh, John H.

    1995-03-01

    Deep surface grating structures make possible the fabrication of DFB and DBR structures where the usual epitaxial regrowth processes which compromise device yield and reliability are avoided. A key requirement is that the gratings are etched to a well-controlled depth position close to the waveguide core. This paper describes the fabrication processes for the grating/stripe waveguide structures in both DFB lasers with gratings exterior to a central stripe (effectively providing refractive index confinement) and DBR lasers with gratings etched into the central ridge region. Issues of etch depth precision, grating pattern definition using either electron beam lithography or holography and measurement of the grating coupling coefficient, K, are addressed. Both pulsed and CW measurements of DFB laser performance have been carried out including lasers with a novel (lambda) /4 shift. In the DBR lasers, quantum well intermixing via impurity free vacancy disordering has been used to reduce the optical absorption in the unpumped region below the reflector grating. A direction extension of this intermixing approach will allow the development of a more general waveguide-based integration technology in which DFB and DBR lasers are combined with passive waveguide sections and other discrete devices to form a complete photonic chip. The prospects for successful implementation of this integration discussed and an example given using a surface grating DFB laser.

  5. Portrait of ependymoma recurrence in children: biomarkers of tumor progression identified by dual-color microarray-based gene expression analysis.

    Directory of Open Access Journals (Sweden)

    Matthieu Peyre

    Full Text Available BACKGROUND: Children with ependymoma may experience a relapse in up to 50% of cases depending on the extent of resection. Key biological events associated with recurrence are unknown. METHODOLOGY/PRINCIPAL FINDINGS: To discover the biology behind the recurrence of ependymomas, we performed CGHarray and a dual-color gene expression microarray analysis of 17 tumors at diagnosis co-hybridized with the corresponding 27 first or subsequent relapses from the same patient. As treatment and location had only limited influence on specific gene expression changes at relapse, we established a common signature for relapse. Eighty-seven genes showed an absolute fold change ≥2 in at least 50% of relapses and were defined as the gene expression signature of ependymoma recurrence. The most frequently upregulated genes are involved in the kinetochore (ASPM, KIF11 or in neural development (CD133, Wnt and Notch pathways. Metallothionein (MT genes were downregulated in up to 80% of the recurrences. Quantitative PCR for ASPM, KIF11 and MT3 plus immunohistochemistry for ASPM and MT3 confirmed the microarray results. Immunohistochemistry on an independent series of 24 tumor pairs at diagnosis and at relapse confirmed the decrease of MT3 expression at recurrence in 17/24 tumor pairs (p = 0.002. Conversely, ASPM expression was more frequently positive at relapse (87.5% vs 37.5%, p = 0.03. Loss or deletion of the MT genes cluster was never observed at relapse. Promoter sequencing after bisulfite treatment of DNA from primary tumors and recurrences as well as treatment of short-term ependymoma cells cultures with a demethylating agent showed that methylation was not involved in MT3 downregulation. However, in vitro treatment with a histone deacetylase inhibitor or zinc restored MT3 expression. CONCLUSIONS/SIGNIFICANCE: The most frequent molecular events associated with ependymoma recurrence were over-expression of kinetochore proteins and down-regulation of

  6. Fibres For Sensors

    Science.gov (United States)

    Payne, D. N.

    1984-11-01

    Sensors which rely on the external modulation of the properties of an optical fibre (intrinsic sensors) are receiving much attention since they can be made extremely sensitive, and can be used for distributed measurements. Distributed sensing provides some particularly exciting prospects for acoustic, magnetic and electric field monitoring. To date, however, the great majority of experimental and commercial fibre sensors employ telecommunications-grade fibres, largely as a result of their ready availability. Not only does this policy frequently lead to a design compromise, but in some cases makes the performance marginal or untenable as a result of excessive environmental sensitivity. Despite this, little attention has been given to the design of special sensor fibres with enhanced (or depressed) sensitivity to specific measurands. The position is somewhat better with respect to fibres designed to eliminate sensor polarisation problems (e.g. polar isation-maintaining fibres), but even here further work is required to provide the performance demanded.

  7. DFB Lasers Between 760 nm and 16 μm for Sensing Applications

    Science.gov (United States)

    Zeller, Wolfgang; Naehle, Lars; Fuchs, Peter; Gerschuetz, Florian; Hildebrandt, Lars; Koeth, Johannes

    2010-01-01

    Recent years have shown the importance of tunable semiconductor lasers in optical sensing. We describe the status quo concerning DFB laser diodes between 760 nm and 3,000 nm as well as new developments aiming for up to 80 nm tuning range in this spectral region. Furthermore we report on QCL between 3 μm and 16 μm and present new developments. An overview of the most interesting applications using such devices is given at the end of this paper. PMID:22319259

  8. Continuously tunable solution-processed organic semiconductor DFB lasers pumped by laser diode

    DEFF Research Database (Denmark)

    Klinkhammer, Sönke; Liu, Xin; Huska, Klaus

    2012-01-01

    The fabrication and characterization of continuously tunable, solution-processed distributed feedback (DFB) lasers in the visible regime is reported. Continuous thin film thickness gradients were achieved by means of horizontal dipping of several conjugated polymer and blended small molecule...... solutions on cm-scale surface gratings of different periods. We report optically pumped continuously tunable laser emission of 13 nm in the blue, 16 nm in the green and 19 nm in the red spectral region on a single chip respectively. Tuning behavior can be described with the Bragg-equation and the measured...

  9. Optical feedback in dfb quantum cascade laser for mid-infrared cavity ring-down spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Terabayashi, Ryohei, E-mail: terabayashi.ryouhei@h.mbox.nagoya-u.ac.jp; Sonnenschein, Volker, E-mail: volker@nagoya-u.jp; Tomita, Hideki, E-mail: tomita@nagoya-u.jp; Hayashi, Noriyoshi, E-mail: hayashi.noriyoshi@h.mbox.nagoya-u.ac.jp; Kato, Shusuke, E-mail: katou.shuusuke@f.mbox.nagoya-u.ac.jp; Jin, Lei, E-mail: kin@nuee.nagoya-u.ac.jp; Yamanaka, Masahito, E-mail: yamanaka@nuee.nagoya-u.ac.jp; Nishizawa, Norihiko, E-mail: nishizawa@nuee.nagoya-u.ac.jp [Nagoya University, Department of Quantum Engineering, Graduate School of Engineering (Japan); Sato, Atsushi, E-mail: atsushi.sato@sekisui.com; Nozawa, Kohei, E-mail: kohei.nozawa@sekisui.com; Hashizume, Kenta, E-mail: kenta.hashizume@sekisui.com; Oh-hara, Toshinari, E-mail: toshinari.ohara@sekisui.com [Sekisui Medical Co., Ltd., Drug Development Solutions Center (Japan); Iguchi, Tetsuo, E-mail: t-iguchi@nucl.nagoya-u.ac.jp [Nagoya University, Department of Quantum Engineering, Graduate School of Engineering (Japan)

    2017-11-15

    A simple external optical feedback system has been applied to a distributed feedback quantum cascade laser (DFB QCL) for cavity ring-down spectroscopy (CRDS) and a clear effect of feedback was observed. A long external feedback path length of up to 4m can decrease the QCL linewidth to around 50kHz, which is of the order of the transmission linewidth of our high finesse ring-down cavity. The power spectral density of the transmission signal from high finesse cavity reveals that the noise at frequencies above 20kHz is reduced dramatically.

  10. DFB diode seeded low repetition rate fiber laser system operating in burst mode

    Science.gov (United States)

    Šajn, M.; Petelin, J.; Agrež, V.; Vidmar, M.; Petkovšek, R.

    2017-02-01

    A distributed feedback (DFB) diode, gain switched to produce pulses from 60 ps at high peak power of over 0.5 W, is used in burst mode to seed a fiber amplifier chain. High seed power, spectral filtering between amplifier stages and pulsed pumping are used to mitigate amplified spontaneous emission (ASE). The effect of pulse pumping synchronized with the seed on the ASE is explored for the power amplifier at low repetition. Different input and output energies at different burst repetition rates are examined and up to 85% reduction in ASE is achieved compared to continuous pumping. Finally, a numerical model is used to predict further reduction of ASE.

  11. Modulation of Frequency Doubled DFB-Tapered Diode Lasers for Medical Treatment

    DEFF Research Database (Denmark)

    Christensen, Mathias; Hansen, Anders Kragh; Noordegraaf, Danny

    2017-01-01

    The use of visible lasers for medical treatments is on the rise, and together with this comes higher expectations for the laser systems. For many medical treatments, such as ophthalmology, doctors require pulse on demand operation together with a complete extinction of the light between pulses. We...... have demonstrated power modulation from 0.1 Hz to 10 kHz at 532 nm with a modulation depth above 97% by wavelength detuning of the laser diode. The laser diode is a 1064 nm monolithic device with a distributed feedback (DFB) laser as the master oscillator (MO), and a tapered power amplifier (PA...

  12. Amplified feedback DFB laser for 40 Gb/s all-optical clock recovery

    Science.gov (United States)

    Chen, Cheng; Sun, Yu; Zhao, Lingjuan; Pan, Jiaoqing; Qiu, Jifang; Liang, Song; Wang, Wei; Lou, Caiyun

    2011-12-01

    A monolithic integrated amplified feedback semiconductor laser (AFL) was fabricated based on quantum well intermixing (QWI) technique. The AFL works as a self-pulsation laser. It consists of a gain-coupled multiple quantum well distribute feedback (DFB) laser diode (LD) section, a passive phase section and an amplified feedback section. The free-running repetition frequency of the AFL can be tuned from 32 GHz to 51 GHz via controlling the feedback strength. All-optical 40 Gb/s clock recovery was experimentally demonstrated using the AFL with a low timing jitter.

  13. Continuously tunable solution-processed organic semiconductor DFB lasers pumped by laser diode.

    Science.gov (United States)

    Klinkhammer, Sönke; Liu, Xin; Huska, Klaus; Shen, Yuxin; Vanderheiden, Sylvia; Valouch, Sebastian; Vannahme, Christoph; Bräse, Stefan; Mappes, Timo; Lemmer, Uli

    2012-03-12

    The fabrication and characterization of continuously tunable, solution-processed distributed feedback (DFB) lasers in the visible regime is reported. Continuous thin film thickness gradients were achieved by means of horizontal dipping of several conjugated polymer and blended small molecule solutions on cm-scale surface gratings of different periods. We report optically pumped continuously tunable laser emission of 13 nm in the blue, 16 nm in the green and 19 nm in the red spectral region on a single chip respectively. Tuning behavior can be described with the Bragg-equation and the measured thickness profile. The laser threshold is low enough that inexpensive laser diodes can be used as pump sources.

  14. Comparison of SHG Power Modulation by Wavelength Detuning of DFB- and DBR-Tapered Laser Diodes

    DEFF Research Database (Denmark)

    Christensen, Mathias; Hansen, Anders Kragh; Noordegraaf, Danny

    2016-01-01

    Pulsed visible lasers are used for a number of applications such as laser displays and medical treatments. Generating this visible light by direct frequency doubling of high power diode lasers opens new possibilities on how the power modulation can be performed. We present an investigation...... of the response of the second harmonic light to perturbations of the infrared laser diode and compare how the response differs for DFB- and DBR-Tapered laser diodes. We show that the visible light can be modulated from CW to kHz with modulation depths above 90% by wavelength detuning the laser diode....

  15. Effect of facet phases and reflectivity on the internal optical field in QWS-DFB semiconductor lasers

    CERN Document Server

    Shahshahani, F; Mirabbaszadeh, K

    2002-01-01

    In this paper, the effects of reflected waves of the facets on the internal optical intensity of semiconductor DFB lasers are investigated. The uniformity of optical intensity along the cavity length is evaluated with flatness parameter. The dependence of this parameter on coupling coefficient, reflectivity and grating phase at the facets is also studied. This investigation shows that in some structures reflected waves of the facets cause optical intensity along the cavity length to have more uniformed distribution than a DFB laser with anti-reflective facets. It is also shown that flatness parameter is very sensitive to grating phase. thus it is necessary for designing a DFB laser to consider the effects of reflected wave and grating phase at both ends of cavity in order to increase the stability of the laser against SHB (Spatial Hole Burning) effect. The effects of reflectivity and grating phase on longitudinal distribution of photon and carrier density above threshold are investigated, too.

  16. Mineral fibres and cancer.

    Science.gov (United States)

    McDonald, J C

    1984-04-01

    A synthesis is presented of the salient findings to date from laboratory and epidemiological research, on the health effects of asbestos and other natural and man-made mineral fibres. Experimental evidence suggests that all mineral fibres are capable of causing fibrosis and malignancy, with chrysotile at least as pathogenic as other fibres. However, penetration, retention and phagocytosis are affected by size and shape and reactivity and durability by physico-chemical properties. Thus it is not surprising that in man the results of exposure vary considerably with fibre type and industrial process. A considerable body of evidence suggests that chrysotile has seldom, if ever, caused peritoneal mesothelioma and that the great majority of pleural mesotheliomas are also attributable to crocidolite or amosite. Without more reliable information on intensity and duration of exposure by fibre type, the epidemiological evidence on this point cannot be wholly conclusive. There are stronger grounds from a limited number of cohort studies for believing that in relation to estimated exposure, the risk of lung cancer has been much higher in textile plants than in fibre production or in the manufacture of friction products, with asbestos-cement plants somewhere in between. The data on man-made fibre production remains equivocal. It is concluded that attempts to regulate asbestos without regard for fibre type, although perhaps adequate for lung cancer and fibrosis, may do little to reduce the risk of mesothelioma. The search for safe fibre substitutes for asbestos will remain difficult until the parameters of pathogenicity are better understood.

  17. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end...... the proximal end of the collection optics into the first end of the input fibre, each collector element having a principal axis for the collection of light defining an optical axis of the collector element. The optical axes of the collector elements are arranged in a radially outward pointing multi...

  18. SALIENT FEATURES OF BAMBOO FIBRE

    Institute of Scientific and Technical Information of China (English)

    Subrata; Das

    2007-01-01

    Bamboo fibre is a regenerated cellulosic fibre produced from bamboo.Starchy pulp is produced from bamboo stems and leaves through a process of alkaline hydrolysis and multi- phase bleaching.Further chemical processes produce bamboo fibre.

  19. SALIENT FEATURES OF BAMBOO FIBRE

    Institute of Scientific and Technical Information of China (English)

    Subrata Das

    2007-01-01

    @@ Bamboo fibre is a regenerated cellulosic fibre produced from bamboo. Starchy pulp is produced from bamboo stems and leaves through a process of alkaline hydrolysis and multiphase bleaching. Further chemical processes produce bamboo fibre.

  20. Integratable and High Speed Complex-Coupled MQW-DFB Lasers Fabricated on Semi-Insulating Substrates

    Institute of Scientific and Technical Information of China (English)

    CHENG Yuan-Bing; WANG Yang; SUN Yu; PAN Jiao-Qing; BIAN Jing; AN Xin; ZHAO ling-juan; WANG Wei

    2009-01-01

    A novel integratable and high speed InGaAsP multi-quantum well (MQW) complex-coupled distributed feedback (DFB) laser is successfully fabricated on a semi-insulating substrate. The fabricated ridge DFB laser exhibits a threshold current of 26 mA, a slope efficiency of 0. 14 W.A-1 and a side mode suppression ratio of 40 dB together with a 3 dB bandwidth of more than 8 GHz. The device is suitable for 10 Gbit/s optical fiber communication.

  1. High speed gain coupled DFB laser diode integrated with MQW electroabsorption modulator

    CERN Document Server

    Kim, M G; Park, S S; Oh, D K; Lee, H T; Kim, H M; Pyun, K E

    1998-01-01

    We have demonstrated stable modulation characteristics of the gain coupled distributed feedback(GC-DFB) laser diode integrated with butt-coupled InGaAsP/InGaAsP strain compensated MQW(multiple-Quantum-well) modulator for high speed optical transmission. For this purpose, we have adopted the InGaAsP/InGaAsP strain compensated MQW structure for the EA modulator and n-doped InGaAs absorptive grating for DFB laser. The typical threshold current and slope efficiency were about 15 mA and 0.1 mW/mA, respectively. The extinction ratio of fabricated integrated device was about 15 dB at -2 V, and the small signal bandwidth was shown to be around 17GHz. We also found that the alpha parameter becomes negative at below a -0.6 V bias voltage. We transmitted 10 Gbps NRZ electrical signal over 90 km of standard single mode optical fiber (SMF). A clearly opened eye diagram was observed in the modulated output.

  2. Dual-Section DFB-QCLs for Multi-Species Trace Gas Analysis

    Directory of Open Access Journals (Sweden)

    Martin J. Süess

    2016-04-01

    Full Text Available We report on the dynamic behavior of dual-wavelength distributed feedback (DFB quantum cascade lasers (QCLs in continuous wave and intermittent continuous wave operation. We investigate inherent etaloning effects based on spectrally resolved light-current-voltage (LIV characterization and perform time-resolved spectral analysis of thermal chirping during long (>5 µs current pulses. The theoretical aspects of the observed behavior are discussed using a combination of finite element method simulations and transfer matrix method calculations of dual-section DFB structures. Based on these results, we demonstrate how the internal etaloning can be minimized using anti-reflective (AR coatings. Finally, the potential and benefits of these devices for high precision trace gas analysis are demonstrated using a laser absorption spectroscopic setup. Thereby, the atmospherically highly relevant compounds CO2 (including its major isotopologues, CO and N2O are simultaneously determined with a precision of 0.16 ppm, 0.22 ppb and 0.26 ppb, respectively, using a 1-s integration time and an optical path-length of 36 m. This creates exciting new opportunities in the development of compact, multi-species trace gas analyzers.

  3. Fibre reinforced polymer nanocomposites

    NARCIS (Netherlands)

    Vlasveld, D.P.N.

    2005-01-01

    In this thesis the results are described of the research on a combination of two types of composites: thermoplastic nanocomposites and continuous fibre composites. In this three-phase composite the main reinforcing phase are continuous glass or carbon fibres, and the matrix consists of a polyamide 6

  4. POLARISATION PRESERVING OPTICAL FIBRE

    DEFF Research Database (Denmark)

    2000-01-01

    . This cladding structure provides polarisation preserving properties to the optical fibre. Optical fibres using this technology may have claddings with elements placed non-periodically as well as in a two-dimensional periodic lattice - such as cladding providing Photonic Band Gap (PBG) effects....

  5. Chalcogenide Fibre Displacement Sensor

    Science.gov (United States)

    2001-06-01

    Fibre optic technology offers the possibility for developing of a variety of physical sensors for a wide range of physical parameters. The main...integrating sphere. The use of chalcogenide rather quartz fibre optic highly increases the Sensitivity of the sensor. Experimental set-up, transmission characteristics and technical parameters are presented.

  6. Fibre lasers for photo-acoustic gas spectroscopy

    Science.gov (United States)

    Arsad, Norhana; Stewart, George

    2011-05-01

    We report here on the use of fiber lasers for recovery of gas absorption line shapes by photo-acoustic spectroscopy. We demonstrate the principle of operation using an erbium-doped fiber, stabilized using a length of un-pumped doped fibre as a saturable absorber. Intensity modulation of the laser output for phase sensitive detection is performed by modulation of the pump current while the wavelength is scanned through the absorption line by a PZT on a fibre Bragg grating. This avoids the distortions that arise in recovered signals due to simultaneous wavelength and intensity modulation, as is the case with conventional DFB diode lasers. Furthermore, the near zero off-line signals with photo-acoustic spectroscopy means that high modulation indices can be used with simple intensity modulation of the fiber laser output. The modulation frequency is set to the acoustic resonance frequency of the gas cell and measurements are made on the P17 absorption line of acetylene at 1535.39nm showing good agreement with the theoretical line-shape profile.

  7. Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Sanchez Bjarklev, Araceli

    Photonic crystal fibres represent one of the most active research areas today in the field of optics. The diversity of applications that may be addressed by these fibres and their fundamental appeal, by opening up the possibility of guiding light in a radically new way compared to conventional...... optical fibres, have spun an interest from almost all areas of optics and photonics. The aim of this book is to provide an understanding of the different types of photonic crystal fibres and to outline some of the many new and exciting applications that these fibres offer. The book is intended for both...... readers with a general interest in photonic crystals, as well as for scientists who are entering the field and desire a broad overview as well as a solid starting point for further specialized stuides. Teh book, therefore, covers bothe general aspects such as the link from classical optics to photonic...

  8. Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Sanchez Bjarklev, Araceli

    Photonic crystal fibres represent one of the most active research areas today in the field of optics. The diversity of applications that may be addressed by these fibres and their fundamental appeal, by opening up the possibility of guiding light in a radically new way compared to conventional...... optical fibres, have spun an interest from almost all areas of optics and photonics. The aim of this book is to provide an understanding of the different types of photonic crystal fibres and to outline some of the many new and exciting applications that these fibres offer. The book is intended for both...... readers with a general interest in photonic crystals, as well as for scientists who are entering the field and desire a broad overview as well as a solid starting point for further specialized stuides. Teh book, therefore, covers bothe general aspects such as the link from classical optics to photonic...

  9. On defining dietary fibre.

    Science.gov (United States)

    DeVries, Jonathan W

    2003-02-01

    Establishing a definition for dietary fibre has historically been a balance between nutrition knowledge and analytical method capabilities. While the most widely accepted physiologically-based definitions have generally been accurate in defining the dietary fibre in foods, scientists and regulators have tended, in practice, to rely on analytical procedures as the definitional basis in fact. As a result, incongruities between theory and practice have resulted in confusion regarding the components that make up dietary fibre. In November 1998 the president of the American Association of Cereal Chemists (AACC) appointed an expert scientific review committee and charged it with the task of reviewing and, if necessary, updating the definition of dietary fibre. The committee was further charged with assessing the state of analytical methodology and making recommendations relevant to the updated definition. After due deliberation, an updated definition of dietary fibre was delivered to the AACC Board of Directors for consideration and adoption (Anon, 2000; Jones 2000b). The updated definition includes the same food components as the historical working definition used for approximately 30 years (a very important point, considering that the majority of the research of the past 30 years delineating the positive health effects of dietary fibre is based on that working definition). However, the updated definition more clearly delineates the make-up of dietary fibre and its physiological functionality. As a result, relatively few changes will be necessary in analytical methodology. Current methodologies, in particular AACC-approved method of analysis 32-05 (Grami, 2000), Association of Official Analytical Chemists' official method of analysis 985.29 (Horwitz, 2000a) or AACC 32-07 (Grami, 2000) Association of Official Analytical Chemists 991.43 (Horwitz, 2000a) will continue to be sufficient and used for most foods. A small number of additional methods will be necessary to

  10. Thermometry Technology of IR Dual Color Composite Simulation System%红外双色复合仿真系统测温技术研究

    Institute of Scientific and Technical Information of China (English)

    张晓龙; 刘英; 张盈; 孙强

    2012-01-01

    In order to simulate the equivalent radiation environment of target and interference in the IR guidance process, and compare the effect of differences in target thermometry between monochromatic thermometry and chromatic thermometry under complex environment, the target and interference on space 6 km is simulated using IR dual color composite simulation system. Through the IR thermal imager calibrated accurately, the target and interference at different temperatures is tested using two methods of temperature measurement-monochromatic thermometry and chromatic thermometry. Blackbody temperature is measured by calibrated MW thermal imager and calibrated LW thermal imager, in the range from 25 ℃ to 40 ℃ of Blackbody temperature, the absolute error limit of LW thermal imager is 0. 5 ℃ , and in the range from 50 ℃ to 120 ℃ of Blackbody temperature, the absolute error limit of MW thermal imager is 0. 2 ℃. When the target temperature is 500 ℃ and the interference temperature is 1000℃ , the temperatures of target measured with LWIR, MWIR and chromatic thermometry are 28. 5 ℃ , 148. 3 ℃ and 322. 4 ℃ , and the temperatures of interference are 56. 7 ℃ , 223. 2 ℃ and 660. 1 ℃ respectively. The experiment result indicates that the characteristics of target temperature can be better reflected using chromatic thermometry than monochromatic thermometry under complex environment.%为了模拟红外制导时目标和干扰的等效辐射环境,并比较单色测温和比色测温两种方法在复杂环境下目标测温效果的差异,利用红外双色复合仿真系统对空间6 km处目标和干扰弹进行了实物模拟.通过准确标定的热像仪,采用单色和比色测温两种方法对不同温度的目标和干扰进行测试.利用经标定的中波热像仪和长波热像仪对黑体测温,黑体温度为(20~60)℃时,长波热像仪的绝对误差限为0.5℃;黑体温度为(50~120)℃时,中波热像仪的绝对误差限为0.2

  11. Fabrication of four-channel DFB laser array using nanoimprint technology for 1.3 μm CWDM systems

    Institute of Scientific and Technical Information of China (English)

    Zhao Jianyi; Chen Xin; Zhou Ning; Huang Xiaodong; Liu Wen

    2014-01-01

    Four-channel monolithically integrated index-coupled distributed-feedback laser array has been fabricated using nanoimprint technology for 1.3 μm CWDM system.Selective lasing wavelength with 20 nm wavelength space is obtained.The present results show that the nanoimprint technology is mature and reliable in the fabrication of DFB laser array.

  12. All-Optical flip-flop operation using a SOA and DFB laser diode optical feedback combination

    DEFF Research Database (Denmark)

    D'Oosterlinck, W.; Öhman, Filip; Buron, Jakob Due;

    2007-01-01

    We report on the switching of an all-optical flip-flop consisting of a semiconductor optical amplifier (SOA) and a distributed feedback laser diode (DFB), bidirectionally coupled to each other. Both simulation and experimental results are presented. Switching times as low as 50ps, minimal required...

  13. All-Optical Flip-Flop Based on an SOA/DFB-Laser Diode Optical Feedback Scheme

    DEFF Research Database (Denmark)

    D'Oosterlinck, W.; Buron, Jakob Due; Öhman, Filip;

    2007-01-01

    We report on the dynamic all-optical flip-flop (AOFF) operation of an optical feedback scheme consisting of a semiconductor optical amplifier (SOA) and a distributed feedback laser diode (DFB-LD), bidirectionally coupled to each other. The operation of the AOFF relies on the interplay between...

  14. Moiré Fibre Bragg Grating Written on Strained Fibres

    Institute of Scientific and Technical Information of China (English)

    孙磊; 冯新焕; 刘艳格; 张伟刚; 袁树忠; 开桂云; 董孝义

    2004-01-01

    Moiré fibre Bragg gratings are made in a single mode fibre and a polarization-maintaining fibre respectively, using an excimer KrF laser and a phase mask. Two gratings are written at the same location of the optical fibre. The wavelength spacing can be finely tuned from 0 to 1.86nm by straining the optical fibre during UV illumination.

  15. Room Temperature InP DFB Laser Array Directly Grown on (001) Silicon

    CERN Document Server

    Wang, Zhechao; Pantouvaki, Marianna; Guo, Weiming; Absil, Philippe; Van Campenhout, Joris; Merckling, Clement; Van Thourhout, Dries

    2015-01-01

    Fully exploiting the silicon photonics platform requires a fundamentally new approach to realize high-performance laser sources that can be integrated directly using wafer-scale fabrication methods. Direct band gap III-V semiconductors allow efficient light generation but the large mismatch in lattice constant, thermal expansion and crystal polarity makes their epitaxial growth directly on silicon extremely complex. Here, using a selective area growth technique in confined regions, we surpass this fundamental limit and demonstrate an optically pumped InP-based distributed feedback (DFB) laser array grown on (001)-Silicon operating at room temperature and suitable for wavelength-division-multiplexing applications. The novel epitaxial technology suppresses threading dislocations and anti-phase boundaries to a less than 20nm thick layer not affecting the device performance. Using an in-plane laser cavity defined by standard top-down lithographic patterning together with a high yield and high uniformity provides ...

  16. Electroabsorption-modulated DFB laser integrated with dual-waveguide spot-size converter

    Science.gov (United States)

    Hou, Lianping; Wang, Wei; Zhu, Hongliang; Wang, Baojun; Zhou, Fan

    2005-11-01

    A 1.55-μm ridge DFB laser and electroabsorption modulator monolithically integrated with a buried-ridge-stripe dual-waveguide spot-size converter at the output port for low-loss coupling to a cleaved single-mode optical fiber was fabricated by means of selective area growth, quantum well intermixing and dual-core technologies. These devices exhibit threshold current of 28 mA, side mode suppression ratio of 38.0 dB, 3-dB modulation bandwidth of 12.0 GHz, modulator extinction ratios of 25.0 dB dc. The output beam divergence angles of the spot-size converter in the horizontal and vertical directions are as small as 8.0°×12.6°, respectively, resulting in 3.2 dB coupling loss with a cleaved single-mode optical fiber.

  17. Monolithic integration of electroabsorption modulator and DFB laser for 10-Gb/s transmission

    Science.gov (United States)

    Zhao, Q.; Pan, J. Q.; Zhang, J.; Li, B. X.; Zhou, F.; Wang, B. J.; Wang, L. F.; Bian, J.; Zhao, L. J.; Wang, W.

    2006-04-01

    A strained InGaAsP-InP multiple-quantum-well DFB laser monolithically integrated with electroabsorption modulator by ultra-low-pressure (22 mbar) selective-area-growth is presented. The integrated chip exhibits superior characteristics, such as low threshold current of 19 mA, single-mode operation around 1550 nm range with side-mode suppression ratio over 40 dB, and larger than 16 dB extinction ratio when coupled into a single-mode fiber. More than 10 GHz modulation bandwidth is also achieved. After packaged in a compact module, the device successfully performs 10-Gb/s NRZ transmission experiments through 53.3 km of standard fiber with 8.7 dB dynamic extinction ratio. A receiver sensitivity of -18.9 dBm at bit-error-rate of 10-10 is confirmed.

  18. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    the proximal end of the collection optics into the first end of the input fibre, each collector element having a principal axis for the collection of light defining an optical axis of the collector element. The optical axes of the collector elements are arranged in a radially outward pointing multi......Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end...... and a second end, and a collection optics, the collection optics being configured to receive light incident on a distal end of the collection optics, to transfer at least partially the incident light to a proximal end of the collection optics, and to couple at least partially the transferred light from...

  19. 42.8 Gb/s ASK homodyne receiver using standard DFB lasers

    Science.gov (United States)

    Becker, D.; Mohr, D.; Datta, S.; Wree, C.; Bhandare, S.; Joshi, A.

    2009-05-01

    Optical synchronous coherent detection is attracting greater attention within the defense and security community because it allows linear recovery both of the amplitude and phase of optical signals. Fiber-based transmission impairments such as chromatic dispersion and polarization mode dispersion can be compensated in the electrical domain. Additionally, synchronous detection offers the potential of improved receiver sensitivity and extended reach versus direct or interferometric detection schemes. 28 Gbaud/112 Gb/s and 42.8 Gbaud transmissions are now being considered in fiber networks worldwide. Due to the lack of broadband high frequency components centered at IF values of 56 GHz and 86 GHz, respectively, the coherent heterodyne approach is not viable for these baud rates. The homodyne approach remains one of the choices available to fully exploit the advantages of synchronous coherent detection at these transmission data rates. In order to implement the homodyne receiver, optical phase locking between the signal and local oscillator laser (LO) is required. Digital approaches for this task rely upon very complex, fast, and high power-consumption chips. A homodyne receiver using an analog approach for phase locking would allow for increased system simplicity at a lower cost. Use of commercial-off-the-shelf (COTS) DFB lasers embedded within the receiver would also increase system feasibility for defense applications. We demonstrate synchronous demodulation of a 42.8 Gbaud signal using an analog optical phase-locked loop. The homodyne system was optimized to use COTS DFB lasers having an aggregate linewidth of ~2 MHz. We also analyze the impact of uncompensated phase noise on receiver performance.

  20. The effect of zinc diffusion on extinction ratio of MQW electroabsorption modulator integrated with DFB laser

    Science.gov (United States)

    Zhou, Daibing; Zhang, Ruikang; Wang, Huitao; Wang, Baojun; Bian, Jing; An, Xin; Zhao, Lingjuan; Zhu, Hongliang; Ji, Chen; Wang, Wei

    2014-11-01

    Monolithically integrated electroabsorption modulated lasers (EML) are widely being used in the optical fiber communication systems, due to their low chip, compact size and good compatible with the current communication systems. In this paper, we investigated the effect of Zinc diffusion on extinction ratio of electroabsorption modulator (EAM) integrated with distributed feedback laser (DFB). EML was fabricated by selective area growth (SAG) technology. The MQW structure of different quantum energy levels was grown on n-type InP buffer layer with 150nm thick SiO2 parallel stripes mask by selective area metal-organic chemical vapor deposition (MOCVD). A 35nm photoluminescence wavelength variation was observed between the laser area (λPL=1535nm) and modulator area (λPL=1500nm) by adjusting the dimension of parallel stripes. The grating (λ=1550nm) was fabricated in the selective area. The device was mesa ridge structure, which was constituted of the DFB laser, isolation gap and modulator. The length of every part is 300μm, 50μm, and 150μm respectively. Two samples were fabricated with the same structure and different p-type Zn-doped concentration, the extinction ratio of heavy Zn-doped device is 12.5dB at -6V. In contrast, the extinction ratio of light Zn-doped device is 20dB at -6V, that was improved for approximate 60%. The different Zn diffusion depth into the MQW absorption layer was observed by Secondary ion mass spectrometer (SIMS). The heavy Zn-doped device diffused into absorption layer deeper than the light Zn-doped device, which caused the large non-uniformity of the electric field in the MQW layer. So the extinction ratio characteristics can be improved by optimizing the Zn-doped concentration of p-type layer.

  1. Low-power colorless all-optical 2R regeneration of 25 Gb/s NRZ signals using a standard DFB laser

    DEFF Research Database (Denmark)

    Huybrechts, Koen; Peucheret, Christophe; Seoane, Jorge

    2010-01-01

    We demonstrate the first all-optical 2R regeneration of 25 Gbit/s NRZ data based on hysteresis in a DFB laser. The scheme results in BER improvement, exhibits low power consumption and is effective after fiber transmission.......We demonstrate the first all-optical 2R regeneration of 25 Gbit/s NRZ data based on hysteresis in a DFB laser. The scheme results in BER improvement, exhibits low power consumption and is effective after fiber transmission....

  2. Study on the DFB fiber laser accelerometer with a metal-shell-packaged single-cylinder mandrel structure

    Science.gov (United States)

    Li, Haitao; Ma, Lina; Yang, Huayong; Luo, Hong

    2014-12-01

    To realize the miniature of fiber laser accelerometers, a metal-shell-packaged single-cylinder mandrel-structured distributed feedback (DFB) fiber laser accelerometer was proposed, whose key sensing component is the DFB fiber laser with a cavity length of 16mm. Simulation results show that when the weight of the mass is 400g, the radius of the thin shell cylinder is 0.5cm, we will find that the resonance frequency of the sensor is 900Hz and its sensitivity reaches 18.1pm/g. It is also shown that its sensitivity achieved 42.8dB.re.rad/g while demodulated by an unbalanced Michelson optical fiber interferometer with 1m path difference. In addition, the effects of its structure and material parameters on the acceleration sensitivity are also studied.

  3. Multibeam Fibre Laser Cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre-laser...... cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

  4. Optical fibre line failure detecting

    OpenAIRE

    Xie, Feng

    2013-01-01

    With the development of modern communications, in order to meet the needs of social development and technological progress the optical fibre communications has become the main communication medium for its high reliability and security. Fibre-optic cable is the channel for signal transmission. It is an important component in the entire fibre-optic network. Once the fibre-optic cable fault happened, the entire communication system would be impacted seriously. When fault occurs, it is important ...

  5. Fibre Optics in Undersea Applications

    Directory of Open Access Journals (Sweden)

    A. K. Talwar

    1984-01-01

    Full Text Available Role of optical fibres for underwater communication cables and hydrophones is discussed. The fibre optics cables provide an excellent solution to the historical bandwidth-diameter problems of conventional coaxial cables.Fibre optic hydrophones are found to have many more advantages apart from high sensitivity and large dynamic range, over the classical sound sensors used in underwater work.

  6. Single-mode optical fibres

    CERN Document Server

    Cancellieri, G

    1991-01-01

    This book describes signal propagation in single-mode optical fibres for telecommunication applications. Such description is based on the analysis of field propagation, considering waveguide properties and also some of the particular characteristics of the material fibre. The book covers such recent advances as, coherent transmissions; optical amplification; MIR fibres; polarization maintaining; polarization diversity and photon counting.

  7. Orientational Distribution of Fibres in Sheared Fibre Suspensions

    Institute of Scientific and Technical Information of China (English)

    KU Xiao-Ke; LIN Jian-Zhong

    2007-01-01

    Motion of fibres in sheared fibre suspensions is simulated numerically by using the lattice Boltzmann method. The orientational distributions of the fibres are presented for different Reynolds numbers, Stokes numbers, shear rate and fibre aspect ratio. Some computational results are compared with the experimental data of pipe Bow, and the qualitative agreement is achieved. The results show that the orientational distributions are greatly affected by the Reynolds numbers, while relatively insensitive to the fibre aspect ratio. The Stokes number and shear rate have obvious influence on the orientation distribution.

  8. Glass Fibre Reinforced Polymers

    NARCIS (Netherlands)

    Nikolaou, N.; Karagianni, L.; Sarakiniatti, M.V.

    2014-01-01

    This "designers' manual" is made during the TIDO-course AR0533 Innovation & Sustainability. Fibre reinforced polymers (FRPs) have been used in many applications over the years, from new construction to retrofitting. They are lightweight, no-corrosive, exhibit high specific strength and specific

  9. Glass Fibre Reinforced Polymers

    NARCIS (Netherlands)

    Nikolaou, N.; Karagianni, L.; Sarakiniatti, M.V.

    2014-01-01

    This "designers' manual" is made during the TIDO-course AR0533 Innovation & Sustainability. Fibre reinforced polymers (FRPs) have been used in many applications over the years, from new construction to retrofitting. They are lightweight, no-corrosive, exhibit high specific strength and specific sti

  10. Phase-locking of commercial DFB lasers for distributed optical fiber sensing applications

    Science.gov (United States)

    Rouse, Chris D.; Brown, Anthony W.; Wylie, Michael T. V.; Colpitts, Bruce G.

    2011-05-01

    The design of a phase/frequency detector-based optical phase-locked loop (PFD-OPLL) capable of locking two commercial semiconductor distributed feedback (DFB) lasers for the purpose of making Brillouin Optical Time-Domain Analysis (BOTDA) measurements is presented. Due to the aperiodic nature of the PFD transfer characteristic, the PFDOPLL offers strong acquisition performance without requiring additional acquisition hardware. Design constraints due to laser linewidths are relaxed by choosing a damping factor of 3.5 instead of 0.707. Loop stability is ensured by reducing the loop propagation delay by as much as possible in hardware, and choosing the loop natural frequency such that the loop bandwidth is below the FM phase reversal frequency of the laser. Results show stable lock performance at 11 GHz with a phase noise of -70dBc/Hz at a 100 Hz offset, a capture range of 2.5 GHz and a tuning range of 3.3 GHz. These specifications exceed the performance requirements of a BOTDA system.

  11. DFB-ridge laser diodes at 894 nm for Cesium atomic clocks

    Science.gov (United States)

    von Bandel, N.; Garcia, M.; Lecomte, M.; Larrue, A.; Robert, Y.; Vinet, E.; Driss, O.; Parrilaud, O.; Krakowski, M.; Gruet, F.; Matthey, R.; Mileti, G.

    2016-02-01

    Time and frequency applications are in need of high accuracy and high stability clocks. Optically pumped compact industrial Cesium atomic clocks are a promising approach that could satisfy these demands. However, the stability of these clocks relies, among others, on the performances of the laser diodes that are used. This issue has led the III-V Lab to commit to the European Euripides-LAMA project that aims to provide competitive compact optical Cesium clocks for ground applications. This work will provide key experience for further space technology qualification. III-V Lab is in charge of the design, fabrication and reliability of Distributed-Feedback diodes (DFB) at 894 nm (D1 line of Cesium) and 852 nm (D2 line). LTF-Unine is in charge of their spectral characterisation. The use of D1 line for pumping will provide simplified clock architecture compared to the D2 line pumping thanks to simpler atomic transitions and a larger spectral separation between lines in the 894 nm case. Also, D1 line pumping overcomes the issue of unpumped "idle states" that occur with D2 line. The modules should provide narrow linewidth (= 10 Hz and 109 Hz2/Hz @ f >= 10 Hz.

  12. A CO trace gas detection system based on continuous wave DFB-QCL

    Science.gov (United States)

    Dang, Jingmin; Yu, Haiye; Sun, Yujing; Wang, Yiding

    2017-05-01

    A compact and mobile system was demonstrated for the detection of carbon monoxide (CO) at trace level. This system adopted a high-power, continuous wave (CW), distributed feedback quantum cascade laser (DFB-QCL) operating at ∼22 °C as excitation source. Wavelength modulation spectroscopy (WMS) as well as second harmonic detection was used to isolate complex, overlapping spectral absorption features typical of ambient pressures and to achieve excellent specificity and high detection sensitivity. For the selected P(11) absorption line of CO molecule, located at 2099.083 cm-1, a limit of detection (LoD) of 26 ppb by volume (ppbv) at atmospheric pressure was achieved with a 1 s acquisition time. Allan deviation analysis was performed to investigate the long term performance of the CO detection system, and a measurement precision of 3.4 ppbv was observed with an optimal integration time of approximate 114 s, which verified the reliable and robust operation of the developed system.

  13. Modelling of photonic crystal fibres

    DEFF Research Database (Denmark)

    Knudsen, Erik

    2003-01-01

    In the presenta ph.d. work a theoretical study of aspects of modelling photonic crystal fibres was carried out. Photonic crystal fibres form a class of optical waveguides where guidance is no longer provided by a difference in refractive index between core and cladding. Instead, guidance...... is provided by an arrangement of air-holes running along the length of the fibre. Depending on the geometry of the fibre, the guiding mechanism may be either arising from the formation of a photonic bandgap in the cladding structure (photonic bandgap fibre), or by an effect resembling total internal...... modes in contiguous fibre segments curved at different radii. Overall microbend loss is expressed as a statistical mean of mismatch losses. Extending a well proven, established formula for macrobending losses in stop index fibres, we provide an estimate of macrobend losses in an air-guiding photonic...

  14. Dual color multiplex TTF-1 + Napsin A and p63 + CK5 immunostaining for subcategorizing of poorly differentiated pulmonary non-small carcinomas into adenocarcinoma and squamous cell carcinoma in fine needle aspiration specimens

    Directory of Open Access Journals (Sweden)

    Seema Sethi

    2012-01-01

    Full Text Available Background: The distinction of lung adenocarcinoma (ADC from squamous cell carcinoma (SCC has important therapeutic implications. Napsin A is a recently developed marker, which has shown high specificity for lung tissue in the surgical pathology specimens. In this study, we have evaluated whether the use of a panel of novel multiplex cocktails of TTF-1 + Napsin A and p63 + CK5 for dual color immunostaining will improve the diagnostic accuracy of lung adenocarcinoma and squamous cell carcinoma in fine needle aspiration (FNA specimens, usually with relatively scant microfragments of diagnostic material. Materials and Methods: Formalin-fixed, paraffin-embedded, adequately cellular FNA cell blocks with a confirmed diagnosis of either ADC (n = 22, SCC (n = 20 or poorly differentiated carcinoma (PDC; n = 7, from a total of 49 consecutive cases, were studied. All these cases had subsequently confirmed diagnosis in biopsies or resection specimens. The sections were immunostained with two color methods of TTF-1 + Napsin A and p63 + CK5 multiplex cocktails. The presence of one or more unequivocal individual tumor cells with convincing brown nuclear TTF-1 and red cytoplasmic Napsin A staining, and cells with brown nuclear p63 and membranous / cytoplasmic CK5 staining were interpreted as ′positive′. Results: All 20 FNA cell blocks from SCC cases were positive for dual stain p63 + CK5 and negative for dual stain TTF-1 + Napsin A. The sensitivity and specificity of the dual immunoexpressions of p63 + CK5 for SCC of lung FNAs were both 100%. All 22 ADC cases were positive with dual stain of TTF-1 + Napsin A and negative for dual stain of p63 + CK5. On follow-up of the surgical pathology specimens, 22 cases were confirmed as ADC. The sensitivity of the dual immunoexpression of TTF-1 + Napsin A for ADC of lung FNAs was 100% and the specificity was also 100%. Of the seven PDC cases, five cases that were positive for dual stain p63 + CK5 and negative for dual

  15. Non-Linear Fibres for Widely Tunable Femtosecond Fibre Lasers

    DEFF Research Database (Denmark)

    Pedersen, Martin Erland Vestergaard

    This Ph.D. thesis investigates how intramodal and intermodal nonlinear processes in few-moded fibres can be used to generate light sources at wavelengths outside the spectral gain-bands of rare-earth-doped opticalfibres. The design of two specialty few-moded fibres for use in a widely tunable...... femtosecond fibre laser is presented. The two fibres are used to facilitate the shifting of a soliton in a cascade configuration from the ytterbium gain-band and to a wavelength of 1280 nm. The temporal pulse duration is on a femtosecond scale with a pulse energy of 5 nJ. The experimentally observed soliton...... self-frequency shift and thereby the outcome of the experimental demonstration of the widely tunable femtosecond fibre laser is shown to depend highly on the chirped of the input pulse into the first few-moded fibre in the cascade setup. Furthermore, an alternative splicing process, with a combination...

  16. Fibre composite in driveline

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, W.

    1989-03-01

    Apart from the geometric degrees of freedom of classical material, fibre composites as material for cardan shafts offer two further free parameters to the design engineer: The fiberment winding angle and the ratio of carbon and glass fibres. This results in a large scope of characteristics in terms of flexibility and torsion. In many cases it is therefore possible to use a one-piece shaft instead of a two-piece shaft, and a specific harmonization of the vibration characteristics of the driveline can be realized. In comparison with shafts made out of steel, mass is reduced by 40-50%, the moment of inertia of the mass by 35-40%. The Composite shaft fulfils the requirements of the performance specifications typical of the components concerned both in terms of engineering and efficiency.

  17. Optical Fibre Bundle

    CERN Multimedia

    These are sample fibre optic cables which are used for networking. Optical fibers are widely used in fiber-optic communications, where they permit transmission over longer distances and at higher bandwidths (data rates) than wire cables. Fibers are used instead of metal wires because signals travel along them with less loss and are also immune to electromagnetic interference. This is useful for somewhere like CERN where magnets with their highly powerful magnetic fields could pose a problem.

  18. Estimation of lifetime distributions on 1550-nm DFB laser diodes using Monte-Carlo statistic computations

    Science.gov (United States)

    Deshayes, Yannick; Verdier, Frederic; Bechou, Laurent; Tregon, Bernard; Danto, Yves; Laffitte, Dominique; Goudard, Jean Luc

    2004-09-01

    High performance and high reliability are two of the most important goals driving the penetration of optical transmission into telecommunication systems ranging from 880 nm to 1550 nm. Lifetime prediction defined as the time at which a parameter reaches its maximum acceptable shirt still stays the main result in terms of reliability estimation for a technology. For optoelectronic emissive components, selection tests and life testing are specifically used for reliability evaluation according to Telcordia GR-468 CORE requirements. This approach is based on extrapolation of degradation laws, based on physics of failure and electrical or optical parameters, allowing both strong test time reduction and long-term reliability prediction. Unfortunately, in the case of mature technology, there is a growing complexity to calculate average lifetime and failure rates (FITs) using ageing tests in particular due to extremely low failure rates. For present laser diode technologies, time to failure tend to be 106 hours aged under typical conditions (Popt=10 mW and T=80°C). These ageing tests must be performed on more than 100 components aged during 10000 hours mixing different temperatures and drive current conditions conducting to acceleration factors above 300-400. These conditions are high-cost, time consuming and cannot give a complete distribution of times to failure. A new approach consists in use statistic computations to extrapolate lifetime distribution and failure rates in operating conditions from physical parameters of experimental degradation laws. In this paper, Distributed Feedback single mode laser diodes (DFB-LD) used for 1550 nm telecommunication network working at 2.5 Gbit/s transfer rate are studied. Electrical and optical parameters have been measured before and after ageing tests, performed at constant current, according to Telcordia GR-468 requirements. Cumulative failure rates and lifetime distributions are computed using statistic calculations and

  19. Fibre-optical microendoscopy.

    Science.gov (United States)

    Gu, M; Bao, H; Kang, H

    2014-04-01

    Microendoscopy has been an essential tool in exploring micro/nano mechanisms in vivo due to high-quality imaging performance, compact size and flexible movement. The investigations into optical fibres, micro-scanners and miniature lens have boosted efficiencies of remote light delivery to sample site and signal collection. Given the light interaction with materials in the fluorescence imaging regime, this paper reviews two classes of compact microendoscopy based on a single fibre: linear optical microendoscopy and nonlinear optical microendoscopy. Due to the fact that fluorescence occurs only in the focal volume, nonlinear optical microendoscopy can provide stronger optical sectioning ability than linear optical microendoscopy, and is a good candidate for deep tissue imaging. Moreover, one-photon excited fluorescence microendoscopy as the linear optical microendoscopy suffers from severe photobleaching owing to the linear dependence of photobleaching rate on excitation laser power. On the contrary, nonlinear optical microendoscopy, including two-photon excited fluorescence microendoscopy and second harmonic generation microendoscopy, has the capability to minimize or avoid the photobleaching effect at a high excitation power and generate high image contrast. The combination of various nonlinear signals gained by the nonlinear optical microendoscopy provides a comprehensive insight into biophenomena in internal organs. Fibre-optical microendoscopy overcomes physical limitations of traditional microscopy and opens up a new path to achieve early cancer diagnosis and microsurgery in a minimally invasive and localized manner.

  20. Analysis of glass fibre sizing

    DEFF Research Database (Denmark)

    Petersen, Helga Nørgaard; Kusano, Yukihiro; Brøndsted, Povl

    2014-01-01

    Glass fibre reinforced polymer composites are widely used for industrial and engineering applications which include construction, aerospace, automotive and wind energy industry. During the manufacturing glass fibres, they are surface-treated with an aqueous solution. This process and the treated...... surfaces are called sizing. The sizing influences the properties of the interface between fibres and a matrix, and subsequently affects mechanical properties of composites. In this work the sizing of commercially available glass fibres was analysed so as to study the composition and chemical structures....... Soxhlet extraction was used to extract components of the sizing from the glass fibres. The glass fibres, their extracts and coated glass plates were analysed by Thermo-Gravimetric Analysis combined with a mass spectrometer (TGA-MS), and Attenuated Total Reflectance Fourier Transform Infrared (ATR...

  1. Modulation characteristics of a DFB-laser with integrated spot-size converter for efficient laser fiber coupling

    Energy Technology Data Exchange (ETDEWEB)

    Zengerle, R.; Greus, C.; Burkhard, H.; Ries, R.; Janning, H.; Kuphal, E. [Deutsche Telekom AG, Technologiezentrum, Darmstadt (Germany); Huebner, B. [Univ. Wuerzburg (Germany). Technische Physik

    1996-12-31

    The RF-modulation emission characteristics of a MQW DFB laser monolithically integrated with a laterally tapered spot-size transformer on InGaAsP/InP were investigated and key results were presented. Despite the relatively simple design of the devices they are characterized by good high speed lasing properties with a direct modulation response exceeding 5 GHz. A simple low loss chip-fiber coupling arrangement with large optical alignment tolerances was demonstrated and is regarded as a particular advantage of these devices. Their experiments confirm the attractivity of this integration concept for low cost laser components in optical transmission systems.

  2. Applications for carbon fibre recovered from composites

    Science.gov (United States)

    Pickering; Liu, Z.; Turner, TA; Wong, KH

    2016-07-01

    Commercial operations to recover carbon fibre from waste composites are now developing and as more recovered fibre becomes available new applications for recovered fibre are required. Opportunities to use recovered carbon fibre as a structural reinforcement are considered involving the use of wet lay processes to produce nonwoven mats. Mats with random in-plane fibre orientation can readily be produced using existing commercial processes. However, the fibre volume fraction, and hence the mechanical properties that can be achieved, result in composites with limited mechanical properties. Fibre volume fractions of 40% can be achieved with high moulding pressures of over 100 bar, however, moulding at these pressures results in substantial fibre breakage which reduces the mean fibre length and the properties of the composite manufactured. Nonwoven mats made from aligned, short carbon fibres can achieve higher fibre volume fractions with lower fibre breakage even at high moulding pressure. A process for aligning short fibres is described and a composite of over 60% fibre volume fraction has been manufactured at a pressures up to 100 bar with low fibre breakage. Further developments of the alignment process have been undertaken and a composite of 46% fibre volume fraction has been produced moulded at a pressure of 7 bar in an autoclave, exhibiting good mechanical properties that compete with higher grade materials. This demonstrates the potential for high value applications for recovered carbon fibre by fibre alignment.

  3. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    DEFF Research Database (Denmark)

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage...... obtained by steam explosion of hemp fibres prior defibrated with pectin degrading enzymes. The S2 layer in the fibre wall of the hemp fibres consisted of1-4 cellulose rich and lignin poor concentric layers constructed of ca. 100 nm thick lamellae. The microfibril angle showed values in the range 0......-10° for the main part of the S2-layer and 70-90° for the S1-layer. The microfibrils that are mainly parallelwith the fibre axis explain the high fibre stiffness, which in defibrated hemp fibres reached 94 GPa. The defibrated hemp fibres had higher fibre stiffness (88-94 GPa) than hemp yarn (60 GPa), which...

  4. Microstructured Optical Fibres

    DEFF Research Database (Denmark)

    1999-01-01

    complete PBGs, which reflects light incident from air or vacuum. Such structures may be used as cladding structures in optical fibres, where light is confined and thereby guided in a hollow core region. In addition, the present invention relates to designs for ultra low-loss PBG waveguiding structures......The present invention relates to a new class of optical waveguides, in which waveguiding along one or more core regions is obtained through the application of the Photonic Bandgap (PBG) effect. The invention further relates to optimised two-dimensional lattice structures capable of providing...

  5. Supercontinuum generation enhanced by conventional Raman amplification at pumping by nanosecond pulses from a directly modulated DFB laser

    Science.gov (United States)

    Rojas-Laguna, Roberto; Gutiérrez-Gutiérrez, Jaime; Kuzin, Evgeny A.; Ibarra-Escamilla, Baldemar; Mendoza-Vázquez, Sergio; Estudillo-Ayala, Julián Moisés; Haus, Joseph W.

    2007-02-01

    We investigated spectral broadening in a standard fiber using a nanosecond directly modulated DFB laser (λ=1549 nm), amplified by a two stage Erbium-doped fiber amplifier. The amplifier provided amplification of 2-mW peak power input pulses to 100-W peak power output pulses. In other hand, the directly modulation of DFB lasers caused transient oscillations at the beginning of pulses. In our case pulses consisted of a 2-ns transient part followed by a steady-state plateau. We used a monochromator to measure the spectrum at the fiber output. A fast photodetector was placed at the monochromator output and pulse shapes were measured for different wavelengths. This technique allowed the separate measurement of different parts in output pulses spectrum. We used the SMF-28 fiber with the standard dispersion of 20 ps/nm-km for our wavelength. We made measurements of the output spectra for three fiber lengths: 0.6-km, 4.46-km and 9.15-km; finding that the initial transient part of a pulse shows supercontinuum generation whereas the plateau results in conventional Raman amplification of this supercontinuum.

  6. Reticulation des fibres lignocellulosiques

    Science.gov (United States)

    Landrevy, Christel

    Pour faire face à la crise économique la conception de papier à valeur ajoutée est développée par les industries papetières. Le but de se projet est l'amélioration des techniques actuelles de réticulation des fibres lignocellulosiques de la pâte à papier visant à produire un papier plus résistant. En effet, lors des réactions de réticulation traditionnelles, de nombreuses liaisons intra-fibres se forment ce qui affecte négativement l'amélioration anticipée des propriétés physiques du papier ou du matériau produit. Pour éviter la formation de ces liaisons intra-fibres, un greffage sur les fibres de groupements ne pouvant pas réagir entre eux est nécessaire. La réticulation des fibres par une réaction de « click chemistry » appelée cycloaddition de Huisgen entre un azide et un alcyne vrai, catalysée par du cuivre (CuAAC) a été l'une des solutions trouvée pour remédier à ce problème. De plus, une adaptation de cette réaction en milieux aqueux pourrait favoriser son utilisation en milieu industriel. L'étude que nous désirons entreprendre lors de ce projet vise à optimiser la réaction de CuAAC et les réactions intermédiaires (propargylation, tosylation et azidation) sur la pâte kraft, en milieu aqueux. Pour cela, les réactions ont été adaptées en milieu aqueux sur la cellulose microcristalline afin de vérifier sa faisabilité, puis transférée à la pâte kraft et l'influence de différents paramètres comme le temps de réaction ou la quantité de réactifs utilisée a été étudiée. Dans un second temps, une étude des différentes propriétés conférées au papier par les réactions a été réalisée à partir d'une série de tests papetiers optiques et physiques. Mots Clés Click chemistry, Huisgen, CuAAC, propargylation, tosylation, azidation, cellulose, pâte kraft, milieu aqueux, papier.

  7. Random distributed feedback fibre lasers

    Science.gov (United States)

    Turitsyn, Sergei K.; Babin, Sergey A.; Churkin, Dmitry V.; Vatnik, Ilya D.; Nikulin, Maxim; Podivilov, Evgenii V.

    2014-09-01

    The concept of random lasers exploiting multiple scattering of photons in an amplifying disordered medium in order to generate coherent light without a traditional laser resonator has attracted a great deal of attention in recent years. This research area lies at the interface of the fundamental theory of disordered systems and laser science. The idea was originally proposed in the context of astrophysics in the 1960s by V.S. Letokhov, who studied scattering with “negative absorption” of the interstellar molecular clouds. Research on random lasers has since developed into a mature experimental and theoretical field. A simple design of such lasers would be promising for potential applications. However, in traditional random lasers the properties of the output radiation are typically characterized by complex features in the spatial, spectral and time domains, making them less attractive than standard laser systems in terms of practical applications. Recently, an interesting and novel type of one-dimensional random laser that operates in a conventional telecommunication fibre without any pre-designed resonator mirrors-random distributed feedback fibre laser-was demonstrated. The positive feedback required for laser generation in random fibre lasers is provided by the Rayleigh scattering from the inhomogeneities of the refractive index that are naturally present in silica glass. In the proposed laser concept, the randomly backscattered light is amplified through the Raman effect, providing distributed gain over distances up to 100 km. Although an effective reflection due to the Rayleigh scattering is extremely small (˜0.1%), the lasing threshold may be exceeded when a sufficiently large distributed Raman gain is provided. Such a random distributed feedback fibre laser has a number of interesting and attractive features. The fibre waveguide geometry provides transverse confinement, and effectively one-dimensional random distributed feedback leads to the generation

  8. Random distributed feedback fibre lasers

    Energy Technology Data Exchange (ETDEWEB)

    Turitsyn, Sergei K., E-mail: s.k.turitsyn@aston.ac.uk [Aston Institute of Photonic Technologies, Aston University, Birmingham B4 7ET (United Kingdom); Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Babin, Sergey A. [Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Churkin, Dmitry V. [Aston Institute of Photonic Technologies, Aston University, Birmingham B4 7ET (United Kingdom); Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Vatnik, Ilya D.; Nikulin, Maxim [Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation); Podivilov, Evgenii V. [Novosibirsk State University, 2 Pirogova str., 630090, Novosibirsk (Russian Federation); Institute of Automation and Electrometry SB RAS, 1 Ac. Koptug. ave., 630090, Novosibirsk (Russian Federation)

    2014-09-10

    The concept of random lasers exploiting multiple scattering of photons in an amplifying disordered medium in order to generate coherent light without a traditional laser resonator has attracted a great deal of attention in recent years. This research area lies at the interface of the fundamental theory of disordered systems and laser science. The idea was originally proposed in the context of astrophysics in the 1960s by V.S. Letokhov, who studied scattering with “negative absorption” of the interstellar molecular clouds. Research on random lasers has since developed into a mature experimental and theoretical field. A simple design of such lasers would be promising for potential applications. However, in traditional random lasers the properties of the output radiation are typically characterized by complex features in the spatial, spectral and time domains, making them less attractive than standard laser systems in terms of practical applications. Recently, an interesting and novel type of one-dimensional random laser that operates in a conventional telecommunication fibre without any pre-designed resonator mirrors–random distributed feedback fibre laser–was demonstrated. The positive feedback required for laser generation in random fibre lasers is provided by the Rayleigh scattering from the inhomogeneities of the refractive index that are naturally present in silica glass. In the proposed laser concept, the randomly backscattered light is amplified through the Raman effect, providing distributed gain over distances up to 100 km. Although an effective reflection due to the Rayleigh scattering is extremely small (∼0.1%), the lasing threshold may be exceeded when a sufficiently large distributed Raman gain is provided. Such a random distributed feedback fibre laser has a number of interesting and attractive features. The fibre waveguide geometry provides transverse confinement, and effectively one-dimensional random distributed feedback leads to the

  9. Pump-phase-noise-free optical wavelength data exchange between QAM signals with 50-GHz channel-spacing using coherent DFB pump.

    Science.gov (United States)

    Lu, Guo-Wei; Albuquerque, André; Puttnam, Benjamin J; Sakamoto, Takahide; Drummond, Miguel; Nogueira, Rogério; Kanno, Atsushi; Shinada, Satoshi; Wada, Naoya; Kawanishi, Tetsuya

    2016-02-22

    An important challenge for implementing optical signal processing functions such as wavelength conversion or wavelength data exchange (WDE) is to avoid the introduction of linear and nonlinear phase noise in the subsystem. This is particularly important for phase noise sensitive, high-order quadrature-amplitude modulation (QAM) signals. In this paper, we propose and experimentally demonstrate an optical data exchange scheme through cascaded 2nd-order nonlinearities in periodically-poled lithium niobate (PPLN) waveguides using coherent pumping. The proposed coherent pumping scheme enables noise from the coherent pumps to be cancelled out in the swapped data after WDE, even with broad linewidth distributed feedback (DFB) pump lasers. Hence, this scheme allows phase noise tolerant processing functions, enabling the low-cost implementation of WDE for high-order QAM signals. We experimentally demonstrate WDEs between 10-Gbaud 4QAM (4QAM) signal and 12.5-Gbaud 4QAM (16QAM) signal with 3.5-MHz linewidth DFB pump lasers and 50-GHz channel spacing. Error-free operation is observed for the swapped QAM signals with coherent DFB pumping whilst use of free-running DFB pumps leads to visible error floors and unrecoverable phase errors. The phase noise cancellation in the coherent pump scheme is further confirmed by study of the recovered carrier phase of the converted signals. In addition to pump phase noise, the influence of crosstalk caused by the finite extinction ratio in WDE is also experimentally investigated for the swapped QAM signals.

  10. Tapered optical fibres for sensing

    Science.gov (United States)

    Martan, Tomas; Kanka, Jiri; Kasik, Ivan; Matejec, Vlastimil

    2008-11-01

    Recently, optical fibre tapers have intensively been investigated for many applications e.g. in telecommunications, medicine and (bio-) chemical sensing. The paper deals with enhancement of evanescent-field sensitivity of the solid-core microstructured fibre with steering-wheel air-cladding. Enhancement of a performance of the microstructured fibre is based on reduction of fibre core diameter down to narrow filament by tapering thereby defined part of light power is guided by an evanescent wave traveling in axial cladding air holes. The original fibre structure with outer diameter of 125 µm was reduced 2×, 2.5×, 3.33×, and 4× for increasing relatively small intensity overlap of guided core mode at wavelength of 1.55 μm with axial air holes. The inner structures of tapered microstructured fibre with steering-wheel aircladding were numerically analyzed and mode intensity distributions were calculated using the FDTD technique. Analyzed fiber tapers were prepared by constructed fibre puller employing 'flame brush technique'.

  11. Helically twisted photonic crystal fibres.

    Science.gov (United States)

    Russell, P St J; Beravat, R; Wong, G K L

    2017-02-28

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic 'space', cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of 'numerical experiments' based on finite-element solutions of Maxwell's equations in a helicoidal frame.This article is part of the themed issue 'Optical orbital angular momentum'. © 2017 The Authors.

  12. Helically twisted photonic crystal fibres

    Science.gov (United States)

    Russell, P. St. J.; Beravat, R.; Wong, G. K. L.

    2017-02-01

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic `space', cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of `numerical experiments' based on finite-element solutions of Maxwell's equations in a helicoidal frame. This article is part of the themed issue 'Optical orbital angular momentum'.

  13. Wetting of flexible fibre arrays.

    Science.gov (United States)

    Duprat, C; Protière, S; Beebe, A Y; Stone, H A

    2012-02-23

    Fibrous media are functional and versatile materials, as demonstrated by their ubiquity both in natural systems such as feathers and adhesive pads and in engineered systems from nanotextured surfaces to textile products, where they offer benefits in filtration, insulation, wetting and colouring. The elasticity and high aspect ratios of the fibres allow deformation under capillary forces, which cause mechanical damage, matting self-assembly or colour changes, with many industrial and ecological consequences. Attempts to understand these systems have mostly focused on the wetting of rigid fibres or on elastocapillary effects in planar geometries and on a fibre brush withdrawn from an infinite bath. Here we consider the frequently encountered case of a liquid drop deposited on a flexible fibre array and show that flexibility, fibre geometry and drop volume are the crucial parameters that are necessary to understand the various observations referred to above. We identify the conditions required for a drop to remain compact with minimal spreading or to cause a pair of elastic fibres to coalesce. We find that there is a critical volume of liquid, and, hence, a critical drop size, above which this coalescence does not occur. We also identify a drop size that maximizes liquid capture. For both wetting and deformation of the substrates, we present rules that are deduced from the geometric and material properties of the fibres and the volume of the drop. These ideas are applicable to a wide range of fibrous materials, as we illustrate with examples for feathers, beetle tarsi, sprays and microfabricated systems.

  14. Helically twisted photonic crystal fibres

    Science.gov (United States)

    Beravat, R.; Wong, G. K. L.

    2017-01-01

    Recent theoretical and experimental work on helically twisted photonic crystal fibres (PCFs) is reviewed. Helical Bloch theory is introduced, including a new formalism based on the tight-binding approximation. It is used to explore and explain a variety of unusual effects that appear in a range of different twisted PCFs, including fibres with a single core and fibres with N cores arranged in a ring around the fibre axis. We discuss a new kind of birefringence that causes the propagation constants of left- and right-spinning optical vortices to be non-degenerate for the same order of orbital angular momentum (OAM). Topological effects, arising from the twisted periodic ‘space’, cause light to spiral around the fibre axis, with fascinating consequences, including the appearance of dips in the transmission spectrum and low loss guidance in coreless PCF. Discussing twisted fibres with a single off-axis core, we report that optical activity in a PCF is opposite in sign to that seen in a step-index fibre. Fabrication techniques are briefly described and emerging applications reviewed. The analytical results of helical Bloch theory are verified by an extensive series of ‘numerical experiments’ based on finite-element solutions of Maxwell's equations in a helicoidal frame. This article is part of the themed issue ‘Optical orbital angular momentum’. PMID:28069771

  15. [Small fibre neuropathy: knowledge is power].

    NARCIS (Netherlands)

    Hoeijmakers, J.G.; Bakkers, M.; Blom, E.W.; Drenth, J.P.H.; Merkies, I.S.; Faber, C.G.

    2012-01-01

    Small fibre neuropathy is a neuropathy of the small non-myelinated C-fibres and myelinated Adelta-fibres. Clinically, an isolated small fibre neuropathy is distinguished by sensory and autonomic symptoms, with practically no abnormalities on neurological examination other than possible distorted pai

  16. Dispersion properties of photonic crystal fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Dridi, Kim;

    1998-01-01

    Approximate dispersion and bending properties of all-silica two-dimensional photonic crystal fibres are characterised by the combination of an effective-index model and classical analysis tools for optical fibres. We believe for the first time to have predicted the dispersion properties of photonic...... crystal fibres. The results strongly indicate that these fibres have potential applications as dispersion managing components...

  17. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    OpenAIRE

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage is unavoidable. The mild defibration was performed by degradation of the pectin and lignin rich middle lamellae around the fibres by cultivation of the mutated white rot fungus Phlebia radiata Cel 26. Fibr...

  18. Periodic Structures in Optical Fibres.

    Science.gov (United States)

    Hand, Duncan Paul

    1990-01-01

    Available from UMI in association with The British Library. The work presented in this thesis concerns techniques for the formation of periodic structures in optical fibres. Two different methods of producing such structures are studied in detail. The first of these involves a breakdown mechanism (known as the 'fibre fuse') that permanently damages the core glass in a periodic manner leaving it unable to guide light. The dynamics of this mechanism are studied, with a view to controlling it for the production of interactive grating structures. It is determined that, due to a sharp rise in fibre absorption with temperature, a thermal shock -wave, with a typical thermal gradient of several hundred degrees Kelvin per micron, forms and travels along the fibre, heating the core glass to such an extent that damage occurs. The periodicity of the resultant damage arises from thermal focusing and defocusing of light in the region of this shock-wave. The second method makes use of the photorefractivity observed in certain germanosilicate fibres on exposure to moderate intensity blue light of wavelength ~480nm or UV light ~240nm. A single-mode fibre transmission filter is demonstrated for the first time, produced by exposing a fibre Sagnac loop mirror to 488nm holographic fringes. Average index changes are shown to occur if such fibres are exposed to spatially uniform blue or UV light, indicating that grating formation is by a different mechanism to the local charge separation which occurs in photorefractive crystals. The various characteristics of these average index changes are measured and analysed, with the conclusion that they result from defect centre formation, driven by two photon absorption with blue light, or single photon absorption with UV light. Associated birefringence changes are also measured and are exploited in a hi-bi fibre to periodically perturb the birefringence axes, producing a narrow-line transmission filter.

  19. Resonance modes in optical fibres

    Institute of Scientific and Technical Information of China (English)

    余寿绵; 余恬

    2002-01-01

    The weakly nonlinear boundary value problem of wave propagation in an optical fibre (for the transverse electric mode, for example) is formulated and a modified linear solution is obtained. It is shown that a self-consistent theory of fibre optics should be weakly nonlinear. The mode of critical refraction that does not exist in the linear theory is obtained, showing that it is a mode consisting of resonance modes. It is shown that the signal carriers in a long fibre are of resonance modes, not normal modes. Some experimental data are given for comparison with the theoretical predictions, and the agreement seems satisfactory.

  20. Intrafusal muscle fibre types in frog spindles.

    Science.gov (United States)

    Diwan, F H; Ito, F

    1989-04-01

    Muscle spindles from bullfrog semitendinosus, iliofibularis and sartorius muscles were examined with light and electron microscopy. Four types of intrafusal muscle fibre were identified according to their diameter, central nucleation and reticular zone arrangement: a large nuclear bag fibre, a medium nuclear bag fibre, and two types of small nuclear chain fibres with and without a reticular zone, respectively. It is suggested that they are comparable to the nuclear bag1, bag2 and chain fibres in mammalian muscle spindles.

  1. Intrafusal muscle fibre types in frog spindles.

    OpenAIRE

    Diwan, F H; Ito, F

    1989-01-01

    Muscle spindles from bullfrog semitendinosus, iliofibularis and sartorius muscles were examined with light and electron microscopy. Four types of intrafusal muscle fibre were identified according to their diameter, central nucleation and reticular zone arrangement: a large nuclear bag fibre, a medium nuclear bag fibre, and two types of small nuclear chain fibres with and without a reticular zone, respectively. It is suggested that they are comparable to the nuclear bag1, bag2 and chain fibres...

  2. Stabilization and frequency control of a DFB laser with a tunable optical reflector integrated in a Silicon Photonics PIC

    CERN Document Server

    Hauck, Johannes; Romero-García, Sebastían; Müller, Juliana; Shen, Bin; Richter, Jens; Merget, Florian; Witzens, Jeremy

    2016-01-01

    We investigate the effect of tunable optical feedback on a commercial DFB laser edge coupled to a Silicon Photonics planar integrated circuit in which a tunable reflector has been implemented by means of a ring resonator based add-drop multiplexer. Controlled optical feedback allows for fine-tuning of the laser oscillation frequency. Under certain conditions it also allows suppression of bifurcation modes triggered by reflections occurring elsewhere on the chip. A semi-analytical model describing laser dynamics under combined optical feedback from the input facet of the edge coupler and from the tunable on-chip reflector fits the measurements. Compensation of detrimental effects from reflections induced elsewhere on a transceiver chip may allow moving isolators downstream in future communications systems, facilitating direct hybrid laser integration in Silicon Photonics chips, provided a suitable feedback signal for a control system can be identified. Moreover, the optical frequency tuning at lower feedback l...

  3. Non-uniform DFB-surface-etched gratings for enhanced performance high power, high brightness broad area lasers

    Science.gov (United States)

    Decker, J.; Fricke, J.; Maaßdorf, A.; Erbert, G.; Tränkle, G.; Crump, P.

    2017-02-01

    Monolithic spectral stabilization is demonstrated in narrow-stripe broad-area lasers (NBA) with high power (5W), conversion efficiency (50%) and high brightness, by using optimized high-order surface-etched DFB gratings. However, surface etched gratings introduce a high index contrast into the semiconductor, leading to the scattering losses increasing rapidly with groove etch depth, limiting efficiency and yield. We therefore review progress in the exploitation of novel, non-uniform grating configurations for improved performance. Devices with non-uniform gratings whose groove etch depth decreases toward the front facet (apodized grating) are shown to operate with enhanced spectrally stable power (6W) compared to devices with uniform gratings.

  4. Integrated high-speed DFB light source and narrow-bandwidth RCE photodetector for WDM fiber communication network application

    Science.gov (United States)

    Wang, Qiming; Li, Cheng; Pan, Zhong; Luo, Yi

    2000-10-01

    Electroabsorption (EA) modulator integrated with partially gain coupling distributed feedback (DFB) lasers have been fabricated and shown high single mode yield and wavelength stability. The small signal bandwidth is about 7.5 GHz. Strained Si1-xGex/Si multiple quantum well (MQW) resonant-cavity enhanced (RCE) photodetectors with SiO2/Si distributed Bragg reflector (DBR) as the mirrors have been fabricated and shown a clear narrow bandwidth response. The external quantum efficiency at 1.3 micrometer is measured to be about 3.5% under reverse bias of 16 V. A novel GaInNAs/GaAs MQW RCE p-i-n photodetector with high reflectance GaAs/AlAs DBR mirrors has also been demonstrated and shown the selectively detecting function with the FWHM of peak response of 12 nm.

  5. Extreme Silica Optical Fibre Gratings

    Directory of Open Access Journals (Sweden)

    Kevin Cook

    2008-10-01

    Full Text Available A regenerated optical fibre Bragg grating that survives temperature cycling up to 1,295°C is demonstrated. A model based on seeded crystallisation or amorphisation is proposed.

  6. Current status of natural fibres

    CSIR Research Space (South Africa)

    Anandjiwala, RD

    2006-12-01

    Full Text Available , automotive, aerospace, marine, electronic, leisure and household uses. This paper will provide an overview of the current status of research and development. It will also deal with future drivers for the growth and competitiveness of natural fibres...

  7. Natural Fibre-Reinforced Biofoams

    Directory of Open Access Journals (Sweden)

    Anne Bergeret

    2011-01-01

    Full Text Available Starches and polylactic acids (PLAs represent the main biobased and biodegradable polymers with potential industrial availability in the next decades for “bio” foams applications. This paper investigates the improvement of their morphology and properties through processing and materials parameters. Starch foams were obtained by melt extrusion in which water is used as blowing agent. The incorporation of natural fibres (hemp, cellulose, cotton linter, sugarcane, coconut in the starch foam induced a density reduction up to 33%, a decrease in water absorption, and an increase in mechanical properties according to the fibre content and nature. PLA foams were obtained through single-screw extrusion using of a chemical blowing agent that decomposed at the PLA melting temperature. A void content of 48% for PLA and 25% for cellulose fibre-reinforced PLA foams and an improvement in mechanical properties were achieved. The influence of a fibre surface treatment was investigated for both foams.

  8. Modeling of photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Barkou, Stig Eigil

    1999-01-01

    Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated.......Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated....

  9. Connectorization of fibre Bragg grating sensors recorded in microstructured polymer optical fibre

    DEFF Research Database (Denmark)

    Abang, A.; Saez-Rodriguez, D.; Nielsen, Kristian

    2013-01-01

    We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate).......We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate)....

  10. Dual-color immunofluorescent labeling with quantum dots of the diabetes-associated proteins aldose reductase and Toll-like receptor 4 in the kidneys of diabetic rats

    Directory of Open Access Journals (Sweden)

    Liu XM

    2015-05-01

    Full Text Available Xiaomin Liu,1,* Rui Hu,2,* Hongwei Lian,1,3 Yang Liu,4 Jing Liu,1 Jianwei Liu,1 Guimiao Lin,5 Liwei Liu,6 Xiaojian Duan,1 Ken-Tye Yong,2 Ling Ye1 1Institute of Gerontology and Geriatrics, Chinese PLA General Hospital, Beijing Key Lab of Aging and Geriatrics, Beijing, People’s Republic of China; 2School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore, Singapore; 3Department of Emergency Medicine, Peking University Third Hospital, Beijing, 4Department of Geriatric Nephrology, Chinese PLA General Hospital, Beijing, 5Key Lab of Biomedical Engineering, School of Medical Sciences, Shenzhen University, Shenzhen, 6School of Science, Changchun University of Science and Technology, Changchun, People’s Republic of China *These authors contributed equally to this work Abstract: Diabetes is one of the major chronic diseases diagnosed worldwide with a common complication of diabetic nephropathy (DN. There are multiple possible mechanisms associated with DN. Aldose reductase (AR and Toll-like receptor 4 (TLR4 may be involved in the occurrence and development of DN. Here, we describe the distribution of AR and TLR4 in cells and renal tissues of diabetic rats through a quantum dot (QD-based immunofluorescence technique and conventional immunohistochemistry. As a new type of nanosized fluorophore, QDs have been recognized in imaging applications and have broad prospects in biomedical research. The results of the reported study demonstrate that both the AR and the TLR4 proteins were upregulated in the renal tissues of diabetic rats. Further, to explore the relationship between AR and TLR4 in the pathogenesis of DN, a dual-color immunofluorescent labeling technique based on QDs was applied, where the expressions of AR and TLR4 in the renal tissues of diabetic rats were simultaneously observed – for the first time, as far as we are aware. The optimized QD-based immunofluorescence technique has not only shown a satisfying

  11. Strength of Concrete Containing Basalt Fibre

    Directory of Open Access Journals (Sweden)

    Parvez Imraan Ansari

    2015-04-01

    Full Text Available This paper presents the comparative study of effect of basalt fibre on compressive and split tensile strength of M40 grade concrete. The basalt fibre was mixed in concrete by (0.5%, 1%, and 1.5% of its total weight of cement in concrete. Results indicated that the strength increases with increase of basalt fibre content up to 1.0% beyond that there is a reduction in strength on increasing basalt fibre. The results show that the concrete specimen with 1.0% of basalt fibre gives better performance when it compared with 0.5%and 1.5% basalt fibre mix in concrete specimens.

  12. Practical Hydrogen Loading of Air Silica Fibres

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Jensen, Jesper Bevensee; Jensen, Jesper Bo Damm

    2005-01-01

    A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown.......A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown....

  13. Carbon nanotubes for ultrafast fibre lasers

    Directory of Open Access Journals (Sweden)

    Chernysheva Maria

    2017-01-01

    Full Text Available Carbon nanotubes (CNTs possess both remarkable optical properties and high potential for integration in various photonic devices. We overview, here, recent progress in CNT applications in fibre optics putting particular emphasis on fibre lasers. We discuss fabrication and characterisation of different CNTs, development of CNT-based saturable absorbers (CNT-SA, their integration and operation in fibre laser cavities putting emphasis on state-of-the-art fibre lasers, mode locked using CNT-SA. We discuss new design concepts of high-performance ultrafast operation fibre lasers covering ytterbium (Yb, bismuth (Bi, erbium (Er, thulium (Tm and holmium (Ho-doped fibre lasers.

  14. Carbon nanotubes for ultrafast fibre lasers

    Science.gov (United States)

    Chernysheva, Maria; Rozhin, Aleksey; Fedotov, Yuri; Mou, Chengbo; Arif, Raz; Kobtsev, Sergey M.; Dianov, Evgeny M.; Turitsyn, Sergei K.

    2017-01-01

    Carbon nanotubes (CNTs) possess both remarkable optical properties and high potential for integration in various photonic devices. We overview, here, recent progress in CNT applications in fibre optics putting particular emphasis on fibre lasers. We discuss fabrication and characterisation of different CNTs, development of CNT-based saturable absorbers (CNT-SA), their integration and operation in fibre laser cavities putting emphasis on state-of-the-art fibre lasers, mode locked using CNT-SA. We discuss new design concepts of high-performance ultrafast operation fibre lasers covering ytterbium (Yb), bismuth (Bi), erbium (Er), thulium (Tm) and holmium (Ho)-doped fibre lasers.

  15. Fibre concentrations and size distributions of airborne fibres in several European man-made mineral fibre plants.

    Science.gov (United States)

    Dodgson, J; Ottery, J; Cherrie, J W; Harrison, G E

    1980-01-01

    Although the nominal diameters of fibres produced in the glass and rock wool industries are usually 6-15 micrometers, these products contain a small proportion of respirable fibres (less than 3 micrometers diameter). Particular significance has been attached to the biological risk arising from the long (greater than 10 micrometers), fine (less than 1 micrometers) fibres. Therefore, the medical research sponsored by the Joint European Medical Research Board into the effects of man-made fibres on health has included detailed environmental studies on both the exposure levels to respirable fibres and the fibre size distributions at the European plants selected for epidemiological work. This paper summarizes the results obtained so far. The size distributions (length and diameter) of the airborne man-made mineral fibres are compared with similar data previously reported for airborne asbestos fibres.

  16. Thermal analysis of bicomponent fibres

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, J.I. [Room I-320-D, ETS Ingenieros Industriales, Universidad de Malaga, Plaza El Ejido, s/n, 29013-Malaga (Spain)

    2007-02-15

    A one-dimensional model of amorphous bicomponent spun fibres derived from the use of perturbation methods based on the slenderness ratio is presented. The model accounts for gravitational, surface tension, axial heat conduction, viscous dissipation and the nonlinear dependence of the dynamic viscosity law on temperature, but does not consider latent heat effects and the radial gradients of temperature and assumes Newtonian rheology. Studies on the effects of the thermal parameters on the compound fibre's geometry and solidification have been performed, and show that the activation energy of the dynamic viscosity laws have a paramount effect on the fibre's cooling, shape, and axial stresses on the core and sheath. In particular, it is shown that, when the activation energy of the viscosity law for the core is higher than that for the sheath, the axial stresses on the core are monotonic functions of the distance along the fibre and higher than those on the sheath, whereas those in the latter may exhibit a nonmonotonic behavior as functions of the thermal conductivity, heat losses and thermal inertia. Despite its limitations, the model presented here represents an improvement over available one-dimensional models for non-isothermal compound or bicomponent fibres. (author)

  17. Novel Helmholtz-based photoacoustic sensor for trace gas detection at ppm level using GaInAsSb/GaAlAsSb DFB lasers.

    Science.gov (United States)

    Mattiello, Mario; Niklès, Marc; Schilt, Stéphane; Thévenaz, Luc; Salhi, Abdelmajid; Barat, David; Vicet, Aurore; Rouillard, Yves; Werner, Ralph; Koeth, Johannes

    2006-04-01

    A new and compact photoacoustic sensor for trace gas detection in the 2-2.5 microm atmospheric window is reported. Both the development of antimonide-based DFB lasers with singlemode emission in this spectral range and a novel design of photoacoustic cell adapted to the characteristics of these lasers are discussed. The laser fabrication was made in two steps. The structure was firstly grown by molecular beam epitaxy then a metallic DFB grating was processed. The photoacoustic cell is based on a Helmholtz resonator that was designed in order to fully benefit from the highly divergent emission of the antimonide laser. An optimized modulation scheme based on wavelength modulation of the laser source combined with second harmonic detection has been implemented for efficient suppression of wall noise. Using a 2211 nm laser, sub-ppm detection limit has been demonstrated for ammonia.

  18. Electroabsorption modulators integrated with DFB lasers based on identical active double-stack MQW-layer structure with high-frequency performance

    Science.gov (United States)

    Stegmueller, Bernhard; Hanke, Christian

    2003-12-01

    Electro optic modulators are key components for fiber optic transmission at data rates exceeding 10Gbit/s. The monolithic integration of an electroabsorption (EA) modulator applying the quantum confined stark effect with a distributed feedback (DFB) laser diode was demonstrated using a novel approach based on a double-stack multiple quantum well (MQW) structure. This novel approach using an identical MQW layer structure for both devices, the DFB laser diode and the EA modulator, will be described and discussed. Recently, a maximum 3dB-cutoff frequency of 25 GHz was measured. Further experimental results obtained from devices operating at 1.3 μm and 1.55 μm, respectively, exhibit the potential of these devices for high-speed data rate transmission.

  19. Biopersistence of man-made vitreous fibres.

    Science.gov (United States)

    Muhle, H; Bellmann, B

    1995-10-01

    Methods for the determination of biodurability of man-made vitreous fibres are reviewed. For mineral wools the first step was the preparation of respirable fibre fractions. Fibres were administered to rats by inhalation or by intratracheal instillation. After serial sacrifice their lungs were digested by low-temperature ashing or by hypochlorite. The total number of fibres per lung and the distributions of length and diameter were analysed by electron microscopy. This resulted in a bivariate distribution of fibres at the various sacrifice dates. If the logarithm of the number of fibres decreased approximately linearly with time after exposure then the elimination kinetics of fibres can be characterized by a half-time. The half-times were compared between various experiments with rats exposed to mineral wool samples. In summary good agreement was found for the elimination of fibres after long-term inhalation and intratracheal instillation whereas shorter half-times were found after short-term inhalation.

  20. Underwater Acoustic Sensing with Optical Fibres

    Directory of Open Access Journals (Sweden)

    V. V. Rampal

    1982-01-01

    Full Text Available The use of optical fibres for the detection of acoustic pressure underwater has been discussed with particular reference to the recent literature on the development of fibre optic hydrophones.

  1. Hollow Core Photonic Crystal Fibre Comprising a Fibre Grating in the Cladding and its Applications

    DEFF Research Database (Denmark)

    2010-01-01

    An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction.......An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction....

  2. Exposure assessment for airborne man-made mineral fibres: the role of fibre dimensions.

    Science.gov (United States)

    Rosenthal, F S

    1993-08-01

    Environmental exposures to man-made mineral fibres (MMMF) typically contain fibres which are polydisperse with respect to fibre dimensions. Fibre dimensions may influence their biological action through effects on: the efficiency of transport to target tissues; the residence time in target tissues; and the biological activity of fibres in contact with target cells. This variability of biological activity vs fibre dimensions should be accounted for when assessing exposure for epidemiological studies of the risk of cancer in subjects exposed to MMMF. In order to provide insight into the influence of fibre dimensions on the potential carcinogenicity of MMMF, this paper reviews literature concerning the sites of lung tumours, regional fibre deposition, biological effects of fibres in in vivo and in vitro systems, dissolution rates of fibres and rates of physiological clearance of inhaled particles. Tumorigenicity of fibres in contact with target tissue appears to be primarily a function of fibre length, whereas both fibre diameter and fibre length may affect the penetration of fibres through the respiratory tract as well as their residence time in target tissues. A methodology is presented to use this information to compute estimates of biologically effective exposure from the joint distribution of fibre lengths and diameters found in an environmental exposure.

  3. LHCb Upgrade: Scintillating Fibre Tracker

    Science.gov (United States)

    Tobin, Mark

    2016-07-01

    The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less read-out system. All front-end electronics will be replaced and several sub-detectors must be redesigned to cope with higher occupancy. The current tracking detectors downstream of the LHCb dipole magnet will be replaced by the Scintillating Fibre (SciFi) Tracker. The SciFi Tracker will use scintillating fibres read out by Silicon Photomultipliers (SiPMs). State-of-the-art multi-channel SiPM arrays are being developed to read out the fibres and a custom ASIC will be used to digitise the signals from the SiPMs. The evolution of the design since the Technical Design Report in 2014 and the latest R & D results are presented.

  4. Fibre Optics In Coal Mining

    Science.gov (United States)

    Cooper, Paul

    1984-08-01

    Coal mines have a number of unique problems which affect the use of fibre optic technology. These include a potentially explosive atmosphere due to the evolution of methane from coal, and a dirty environment with no cleaning facilities readily available. Equipment being developed by MRDE to allow the exploitation of optical fibres underground includes: A hybrid electrical/fibre optic connector for the flexible power trailing cable of the coal-face shearer; An Intrinsically Safe (IS) pulsed laser transmitter using Frequency Shift Key (FSK) data modulation; An IS Avalanche Photo Diode Receiver suitable for pulsed & continuous wave optical signals; A mine shaft and roadway cable/ connector system incorporating low loss butt-splices and preterminated demountable connectors.

  5. LHCb Upgrade: Scintillating Fibre Tracker

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, Mark, E-mail: Mark.Tobin@epfl.ch

    2016-07-11

    The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less read-out system. All front-end electronics will be replaced and several sub-detectors must be redesigned to cope with higher occupancy. The current tracking detectors downstream of the LHCb dipole magnet will be replaced by the Scintillating Fibre (SciFi) Tracker. The SciFi Tracker will use scintillating fibres read out by Silicon Photomultipliers (SiPMs). State-of-the-art multi-channel SiPM arrays are being developed to read out the fibres and a custom ASIC will be used to digitise the signals from the SiPMs. The evolution of the design since the Technical Design Report in 2014 and the latest R & D results are presented.

  6. Wavelength Filters in Fibre Optics

    CERN Document Server

    Venghaus, Herbert

    2006-01-01

    Wavelength filters constitute an essential element of fibre-optic networks. This book gives a comprehensive account of the principles and applications of such filters, including their technological realisation. After an introductory chapter on wavelength division multiplexing in current and future fibre optic networks follows a detailed treatment of the phase characteristics of wavelength filters, a factor frequently neglected but of significant importance at high bit rates. Subsequent chapters cover three-dimensional reflection of gratings, arrayed waveguide gratings, fibre Bragg gratings, Fabry-Perot filters, dielectric multilayer filters, ring filters, and interleavers. The book explains the relevant performance parameters, the particular advantages and shortcomings of the various concepts and components, and the preferred applications. It also includes in-depth information on the characteristics of both commercially available devices and those still at the R&D stage. All chapters are authored by inter...

  7. Ductility Performance of Hybrid Fibre Reinforced Concrete

    OpenAIRE

    S. Eswari; P.N. Raghunath; Suguna, K

    2008-01-01

    This study presents a study on the ductility performance of hybrid fibre reinforced concrete. The influence of fibre content on the ductility performance of hybrid fibre reinforced concrete specimens having different fibre volume fractions was investigated. The parameters of investigation included modulus of rupture, ultimate load, service load, ultimate and service load deflection, crack width, energy ductility and deflection ductility. A total of 27 specimens, 100×100×500 mm, were tested to...

  8. Photonic crystal fibres and effective index approaches

    DEFF Research Database (Denmark)

    Riishede, Jesper; Libori, Stig E. Barkou; Bjarklev, Anders Overgaard

    2001-01-01

    Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres.......Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres....

  9. Photonic-crystal fibre: Mapping the structure

    DEFF Research Database (Denmark)

    Markos, Christos

    2015-01-01

    The demonstration of real-time and non-destructive Doppler-assisted tomography of the internal structure of photonic-crystal fibres could aid the fabrication of high-quality fibres with enhanced performance.......The demonstration of real-time and non-destructive Doppler-assisted tomography of the internal structure of photonic-crystal fibres could aid the fabrication of high-quality fibres with enhanced performance....

  10. Local fibred right adjoints are polynomial

    DEFF Research Database (Denmark)

    Kock, Anders; Kock, Joachim

    2013-01-01

    For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense......For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense...

  11. Optical Fibre Based Frequency Shifters Project

    Science.gov (United States)

    1991-01-28

    A fibre optic frequency shifter can be used to replace the Bragg cell acousto-optic modulator, currently used to generate low frequency optical...carriers, in fibre optic communications and sensor systems. This new form of frequency shifter, being an all fibre device, in which the propagating optical...large number of workers in recent years, (for example references [2-81 and those contained therein). The main elements of a fibre - optic frequency

  12. Optimal Extraction of Fibre Optic Spectroscopy

    CERN Document Server

    Sharp, R

    2009-01-01

    We report an optimal extraction methodology, for the reduction of multi-object fibre spectroscopy data, operating in the regime of tightly packed (and hence significantly overlapping) fibre profiles. The routine minimises crosstalk between adjacent fibres and statistically weights the extraction to reduce noise. As an example of the process we use simulations of the numerous modes of operation of the AAOmega fibre spectrograph and observational data from the SPIRAL Integral Field Unit at the Anglo-Australian Telescope.

  13. Surface-emitting circular DFB, disk-, and ring-Bragg resonator lasers with chirped gratings. II: nonuniform pumping and far-field patterns.

    Science.gov (United States)

    Sun, Xiankai; Yariv, Amnon

    2009-01-05

    This is a continuation of our previous work [Opt. Express 16, 9155 (2008)]. In this paper we investigate the effect of nonuniform pumping on the modal properties of surface-emitting chirped circular grating lasers. By numerically solving the coupled-mode equations and matching the boundaries we compare and discuss the threshold pump levels and frequency detuning factors for three pumping profiles: uniform, Gaussian, and annular. Depending on the overlap of the pumping and modal profiles, Gaussian pumping results in the lowest threshold pump levels except for the fundamental mode of ring Bragg resonator laser, and annular pumping provides larger threshold discrimination between the fundamental and first-order modes of circular DFB and ring Bragg resonator lasers, which is favorable for single-mode operation in these lasers. We also study the far-field patterns of the fundamental modes of circular DFB, disk-, and ring- Bragg resonator lasers. Circular DFB and ring Bragg resonator lasers have the first-order dominating peak, while disk Bragg resonator laser exhibits the zeroth-order dominating peak.

  14. Fibre Optic Communication Key Devices

    CERN Document Server

    Grote, Norbert

    2012-01-01

    The book gives an in-depth description of the key devices of current and next generation fibre optic communication networks. In particular, the book covers devices such as semiconductor lasers, optical amplifiers, modulators, wavelength filters, and detectors but the relevant properties of optical fibres as well. The presentations include the physical principles underlying the various devices, the technologies used for the realization of the different devices, typical performance characteristics and limitations, and development trends towards more advanced components are also illustrated. Thus the scope of the book spans relevant principles, state-of-the-art implementations, the status of current research and expected future components.

  15. Portable smartphone optical fibre spectrometer

    Science.gov (United States)

    Hossain, Md. Arafat; Canning, John; Cook, Kevin; Jamalipour, Abbas

    2015-09-01

    A low cost, optical fibre based spectrometer has been developed on a smartphone platform for field-portable spectral analysis. Light of visible wavelength is collected using a multimode optical fibre and diffracted by a low cost nanoimprinted diffraction grating. A measurement range over 300 nm span (λ = 400 to 700 nm) is obtained using the smartphone CMOS chip. The spectral resolution is Δλ ~ 0.42 nm/screen pixel. A customized Android application processed the spectra on the same platform and shares with other devices. The results compare well with commercially available spectrometer.

  16. Modulated quaternion lapped transform and its application in dual color image watermarking%四元数调制重叠变换及其在双彩色图像数字水印中的应用

    Institute of Scientific and Technical Information of China (English)

    陈北京; 田翠翠; 戴慧; 王定成; 舒华忠

    2013-01-01

    为了整体处理彩色图像,基于四元数彩色图像表示方法和四元数代数理论,定义了四元数调制重叠变换(MQLT),将传统的主要针对灰度图像的复数调制重叠变换(MCLT)推广应用于彩色图像处理中。然后,通过建立 MQLT 系数与彩色图像三通道传统 MCLT 系数之间的关系,分析了 MQLT 系数的对称特性,并基于 MQLT 变换及其系数对称特性,结合 Arnold 变换和冗余嵌入策略,提出了一种鲁棒的双彩色图像盲水印算法。为了避免水印能量损失,修改系数嵌入水印时遵循了系数的对称性。所提算法充分利用了四维频域空间,将有意义的彩色水印嵌入到彩色载体图像中。实验结果表明,所提算法在不可见性和鲁棒性2个方面均明显优于采用传统三通道分别处理思想的 MCLT 算法。%In order to process color images holistically,by using the quaternion representation of col-or images and the algebra of quaternion,modulated quaternion lapped transform (MQLT)is defined to generalize the conventional modulated complex lapped transform (MCLT)for gray images and applied into the process of color images.Then,the symmetric properties of the MQLT coefficients are analyzed after the establishment of the relationships between the MQLT coefficients and the MCLT coefficients of three channels.Finally,combining with the Arnold transform and multiple re-dundant embedding strategy,a robust blind dual color image watermarking algorithm is proposed based on MQLT and its symmetric property.In order to avoid watermark energy loss,the MQLT coefficients are modified to embed watermarks according to their symmetric properties.The proposed algorithm fully utilizes four-dimensional MQLT domain and embeds a meaningful color watermark into a color host image.The experimental results show that the proposed algorithm is superior to the conventional component-wise algorithm based on the MCLT in terms of

  17. Friction and wear of human hair fibres

    Science.gov (United States)

    Bowen, James; Johnson, Simon A.; Avery, Andrew R.; Adams, Michael J.

    2016-06-01

    An experimental study of the tribological properties of hair fibres is reported, and the effect of surface treatment on the evolution of friction and wear during sliding. Specifically, orthogonally crossed fibre/fibre contacts under a compressive normal load over a series of 10 000 cycle studies are investigated. Reciprocating sliding at a velocity of 0.4 mm s-1, over a track length of 0.8 mm, was performed at 18 °C and 40%-50% relative humidity. Hair fibres retaining their natural sebum were studied, as well as those stripped of their sebum via hexane cleaning, and hair fibres conditioned using a commercially available product. Surface topography modifications resulting from wear were imaged using scanning electron microscopy and quantified using white light interferometry. Hair fibres that presented sebum or conditioned product at the fibre/fibre junction exhibited initial coefficients of friction at least 25% lower than those that were cleaned with hexane. Coefficients of friction were observed to depend on the directionality of sliding for hexane cleaned hair fibres after sufficient wear cycles that cuticle lifting was present, typically on the order 1000 cycles. Cuticle flattening was observed for fibre/fibre junctions exposed to 10 mN compressive normal loads, whereas loads of 100 mN introduced substantial cuticle wear and fibre damage.

  18. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available animal hair fibres L Hunter, CSIR and Nelson Mandela Metropolitan University (NMMU), South Africa Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury...

  19. Occupational ceramic fibres dermatitis in Poland.

    Science.gov (United States)

    Kieć-Swierczyńska, M; Wojtczak, J

    2000-07-01

    Recently, the use of asbestos has been considerably limited in Poland, with the simultaneous increase in the manufacture, processing and application of man-made mineral fibres, which includes ceramic fibres. The aims of this study were (1) to assess the type and frequency of dermal changes caused by the irritant activity of ceramic fibres among workers at the plants that manufacture packing and insulation products; and (2) to compare the irritant activity of Polish-made L-2 and L-3 ceramic fibres with that of the Thermowool ceramic fibres made in England. Workers (n = 226) who were exposed to ceramic fibres underwent dermatological examination. Patch tests with the standard allergen set, together with samples of the fibres L-2, L-3, and Thermowool fibres, were applied to all the workers. It has been shown that the Polish-made L-2 and L-3 fibres differed from Thermowool fibres in that the L-2 and L-3 fibres contained zirconium and were coarser. The proportion of filaments with diameters above 3 microns was 11.1% in the L-3 fibre and 6.3% in the L-2 fibre samples. The Thermowool fibre did not contain filaments thicker than 3 microns. Evident dermal changes, resulting from strong irritant activity of the fibres, were detected in 109 (48.2%) of the workers examined. Irritant contact dermatitis acuta (maculae, sometimes papulae and small crusts on the upper extremities, trunk, and lower extremities), disappearing after 2-3 days, was found in 50 (22.1%) workers. Irritant contact dermatitis chronica (diffuse permanent erythema with numerous telangiectasiae on the lateral portions of the face and neck, on the trunk, behind the auricles) was detected in 40 (17.7%) workers. The remaining 19 (8.4%) workers had both types of dermal change. All examined workers complained of very strong itching. The results of the patch tests confirmed the irritant activity of the ceramic fibres. Erythema without oedema, persisting for up to 96 h, appeared at the places where the fibres had

  20. Stabilization and Frequency Control of a DFB Laser With a Tunable Optical Reflector Integrated in a Silicon Photonics PIC

    Science.gov (United States)

    Hauck, Johannes; Schrammen, Matthias; Romero-Garcia, Sebastian; Muller, Juliana; Shen, Bin; Richter, Jens; Merget, Florian; Witzens, Jeremy

    2016-12-01

    We investigate the effect of tunable optical feedback on a commercial DFB laser edge coupled to a Silicon Photonics planar integrated circuit in which a tunable reflector has been implemented by means of a ring resonator based add-drop multiplexer. Controlled optical feedback allows for fine-tuning of the laser oscillation frequency. Under certain conditions it also allows suppression of bifurcation modes triggered by reflections occurring elsewhere on the chip. A semi-analytical model describing laser dynamics under combined optical feedback from the input facet of the edge coupler and from the tunable on-chip reflector fits the measurements. Compensation of detrimental effects from reflections induced elsewhere on a transceiver chip may allow moving isolators downstream in future communications systems, facilitating direct hybrid laser integration in Silicon Photonics chips, provided a suitable feedback signal for a control system can be identified. Moreover, the optical frequency tuning at lower feedback levels can be used to form a rapidly tunable optical oscillator as part of an optical phase locked loop, circumventing the problem of the thermal to free carrier effect crossover in the FM response of injection current controlled semiconductor laser diodes.

  1. A PHOTONIC BAND GAP FIBRE

    DEFF Research Database (Denmark)

    1999-01-01

    An optical fibre having a periodicidal cladding structure provididing a photonic band gap structure with superior qualities. The periodical structure being one wherein high index areas are defined and wherein these are separated using a number of methods. One such method is the introduction...

  2. Cool application for Optical Fibres

    CERN Multimedia

    2001-01-01

    In a new first for CERN, optical fibres have been put on test to measure very low temperatures. If these tests prove successful, this new technology could lead to important cost-saving changes in the way the temperatures of superconducting magnets are measured. There was excitement in the air last March when the team led by Walter Scandale and Luc Thévenaz tested very low temperature measurement using optical fibres. This spring in CERN's Cryogenics lab an idea was put to the test as a new kind of low-temperature thermometry using optical fibres was tested down to 2 Kelvin (around 300 degrees below room temperature), and the first results are looking good. Optical fibres are well known for their ability to carry large amounts of data around the world, but it is less well known that they can be used for measuring temperatures. The intuition that they might be able to measure very low temperatures - such as those of the LHC magnets - came to the attention of CERN's Walter Scandale at the Optical Fi...

  3. Compressibility of hemp bast fibres

    NARCIS (Netherlands)

    Westenbroek, A.P.H.; Roekel, van G.J.; Jong, de E.; Weickert, G.; Westerterp, R.K.

    1999-01-01

    A force-based characterization of the extrusion pulping process is necessary to be able to predict the effects of extrusion on fibres. To determine which forces are beneficial and which only cause energy consumption, the nature and the origin of the forces have to be known. This paper discusses the

  4. Threshold temperature optical fibre sensors

    Science.gov (United States)

    Stasiewicz, K. A.; Musial, J. E.

    2016-12-01

    This paper presents a new approach to manufacture a threshold temperature sensor based on a biconical optical fibre taper. The presented sensor employs the influence of variable state of concentration of some isotropic materials like wax or paraffin. Application of the above- mentioned materials is an attempt to prove that there is a possibility to obtain a low-cost, repeatable and smart sensor working as an in-line element. Optical fibre taper was obtained from a standard single mode fibre (SMF28®) by using a low pressure gas burner technique. The diameter of the manufactured tapers was 6.0 ± 0.5 μm with the length of elongation equal to 30.50 ± 0.16 mm. The applied technology allowed to produce tapers with the losses of 0.183 ± 0.015 dB. Application of materials with different temperature transition points made it possible to obtain the threshold work at the temperatures connected directly with their conversion temperature. External materials at the temperatures above their melting points do not influence the propagation losses. For each of them two types of the protection area and position of the optical fibre taper were applied.

  5. Nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch

    is potentially the case for microstructured polymer optical fibres (mPOFs). Another advantage is that polymer materials have a higher biocompatibility than silica, meaning that it is easier to bond certain types of biosensor materials to a polymer surface than to silica. As with silica PCFs, it is difficult...

  6. Mineral fibre persistence and carcinogenicity.

    Science.gov (United States)

    McDonald, J C

    1998-10-01

    Epidemiological research during the past 40 years has demonstrated with increasing clarity that amphibole asbestos fibres--crocidolite, amosite and tremolite--are more carcinogenic than chrysotile. A smaller number of well-controlled studies using lung burden analyses, while adding to the specificity of this conclusion, have shown that amphibole fibres also differ from chrysotile in being far more durable and biopersistent in lung tissue. Analyses of mesothelioma and lung cancer in a large cohort of Canadian chrysotile miners and millers have recently shown that the low-level presence of fibrous tremolite in these mines, rather than the chrysotile, may well be responsible. The high risk of lung cancer, but not of mesothelioma, in the chrysotile textile industry remains anomalous and cannot be explained in this way. These various findings are directly relevant to the choice of the experimental methods which should be used for screening man-made fibres for industrial use. Although it is clear that biopersistence is a major determinant of cancer risk in animals, and perhaps also in man, other factors affecting the biological activity of mineral fibres may also be important.

  7. Strength of Concrete Containing Basalt Fibre

    OpenAIRE

    2015-01-01

    This paper presents the comparative study of effect of basalt fibre on compressive and split tensile strength of M40 grade concrete. The basalt fibre was mixed in concrete by (0.5%, 1%, and 1.5%) of its total weight of cement in concrete. Results indicated that the strength increases with increase of basalt fibre content up to 1.0% beyond that there is a reduction in strength on increasing basalt fibre. The results show that the concrete specimen with 1.0% of basalt fibre gives be...

  8. Characterisation of Natural Fibre Reinforcements and Composites

    Directory of Open Access Journals (Sweden)

    Richard K. Cullen

    2013-01-01

    Full Text Available Recent EU directives (e.g., ELV and WEEE have caused some rethinking of the life cycle implications of fibre reinforced polymer matrix composites. Man-made reinforcement fibres have significant ecological implications. One alternative is the use of natural fibres as reinforcements. The principal candidates are bast (plant stem fibres with flax, hemp, and jute as the current front runners. The work presented here will consider the characterisation of jute fibres and their composites. A novel technique is proposed for the measurement of fibre density. The new rule of mixtures, extended for noncircular cross-section natural fibres, is shown to provide a sensible estimate for the experimentally measured elastic modulus of the composite.

  9. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...... of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish...... the same amount of air pores as in the corresponding concrete without fibres...

  10. Elastic fibres in health and disease.

    Science.gov (United States)

    Baldwin, Andrew K; Simpson, Andreja; Steer, Ruth; Cain, Stuart A; Kielty, Cay M

    2013-08-20

    Elastic fibres are insoluble components of the extracellular matrix of dynamic connective tissues such as skin, arteries, lungs and ligaments. They are laid down during development, and comprise a cross-linked elastin core within a template of fibrillin-based microfibrils. Their function is to endow tissues with the property of elastic recoil, and they also regulate the bioavailability of transforming growth factor β. Severe heritable elastic fibre diseases are caused by mutations in elastic fibre components; for example, mutations in elastin cause supravalvular aortic stenosis and autosomal dominant cutis laxa, mutations in fibrillin-1 cause Marfan syndrome and Weill-Marchesani syndrome, and mutations in fibulins-4 and -5 cause autosomal recessive cutis laxa. Acquired elastic fibre defects include dermal elastosis, whereas inflammatory damage to fibres contributes to pathologies such as pulmonary emphysema and vascular disease. This review outlines the latest understanding of the composition and assembly of elastic fibres, and describes elastic fibre diseases and current therapeutic approaches.

  11. Retained laser fibre: insights and management.

    Science.gov (United States)

    Lekich, C; Hannah, P

    2014-06-01

    To describe a case of retained endovenous laser fibre. To review the literature and Food and Drug Administration device failure reports. To suggest protocols for avoiding this complication and a method of removal. A case of retained fibre removal is described. Fibre removal techniques in vivo and ex vivo in a bovine model on the laboratory bench are presented. Successful in vivo and ex vivo fibre removal was performed using duplex ultrasound scan guided phlebectomy techniques. Unexplained measured fibre-length discrepancies due to misleading manufacturer's packaging was discovered. Simple ultrasound-guided micro-phlebectomy techniques can be used to remove retained laser fibres in the office environment. Laser fibre length measurements before and after treatment are recommended. Some preventive guidelines are described to avoid, or at least diagnose immediately, this complication, such as the 'Laser Eclipse Sign'. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

  12. Characterisation of Flax Fibres and Flax Fibre Composites. Being cellulose based sources of materials

    DEFF Research Database (Denmark)

    Aslan, Mustafa

    that currently have the largest market share for composite applications. However, the most critical limitation in the use of cellulosic fibre composites for structural applications is the lack of well described fibre properties, in particular, the tensile strength. This is due to variations in fibre morphology...... of the internal cell wall structures. This is in contrast to the crack growth in brittle ceramic and glass fibres. Moreover, two typical stress-strain curves (linear and non-linear) measured for the flax fibres were found to be correlated with the amount of defected region in the fibres. The defects are induced...... a similar microstructure at low fibre weight fractions. However, when the fibre content is increased, a difference in porosity content can be observed from the composite cross sections. The nominal tensile strength of the unidirectional flax fibre/LPET composites is measured in the range 180 to 340 MPa...

  13. Fundamentals of fibre-reinforced soil engineering

    CERN Document Server

    Shukla, Sanjay Kumar

    2017-01-01

    This book is intended to serve as a one-stop reference on fibre-reinforced soils. Over the past 30-35 years, the engineering behaviour of randomly distributed/oriented fibre-reinforced soil, also called simply fibre-reinforced soil, has been investigated in detail by researchers and engineers worldwide. Waste fibres (plastic waste fibres, old tyre fibres, etc.) create disposal and environmental problems. Utilization of such fibres in construction can help resolve these concerns. Research studies and some field applications have shown that the fibres can be utilized in large quantities in geotechnical and civil engineering applications in a cost-effective and environmentally friendly manner. This book covers a complete description of fibres, their effects when included within a soil or other similar materials such as the fly ash, and their field applications. It gives a detailed view of fibre-reinforced soil engineering. The book will be useful to students, professional, and researchers alike, and can also ser...

  14. Structural investigation of Mimosa pudica Linn fibre

    Science.gov (United States)

    Patra, S. R.; Pattojoshi, P.; Tiwari, T. N.; Mallick, B.

    2016-12-01

    Sensitive plant (Mimosa pudica Linn.) fibre is a natural fibre with electrically conductive property. Because of its electro-active sensing nature, it has been found very interesting among physicists, chemists, biologists, material scientists and technologists. So far as our knowledge is concerned; there is no report on the X-ray structure of M. pudica fibre using diffraction technique. In the present report, the M. pudica fibre has been extracted from the stem of the herb by sinking the stem in 10% NaOH solution for one week. The diffraction pattern of the fibre is found out to be cellulose-I. The effect of the fibre structure and its orientation due to different mounting have been investigated using X-ray diffraction technique. The I max of cellulose-I has been observed along (002) and (10overline{1)} for the perpendicular and parallel mounting of the native-fibre, respectively. Full width at half maxima of the diffraction profile turns out to be decreased with fibre orientation. Dimension of crystallite size D hkl estimated in the perpendicular mounting D_{hkl}^{ bot } is more as compared to that of the parallel mounting D_{hkl}^{{^{allel } }} . The smallest crystallite sizes observed in both parallel and perpendicular mounting are 18.78 and 30.78 Å respectively. It is expected that the present study may help to analyse the X-ray diffraction of fibre materials in general and natural fibres in particular.

  15. Structural investigation of Mimosa pudica Linn fibre

    Science.gov (United States)

    Patra, S. R.; Pattojoshi, P.; Tiwari, T. N.; Mallick, B.

    2017-04-01

    Sensitive plant ( Mimosa pudica Linn.) fibre is a natural fibre with electrically conductive property. Because of its electro-active sensing nature, it has been found very interesting among physicists, chemists, biologists, material scientists and technologists. So far as our knowledge is concerned; there is no report on the X-ray structure of M. pudica fibre using diffraction technique. In the present report, the M. pudica fibre has been extracted from the stem of the herb by sinking the stem in 10% NaOH solution for one week. The diffraction pattern of the fibre is found out to be cellulose-I. The effect of the fibre structure and its orientation due to different mounting have been investigated using X-ray diffraction technique. The I max of cellulose-I has been observed along (002) and (10\\overline{1)} for the perpendicular and parallel mounting of the native-fibre, respectively. Full width at half maxima of the diffraction profile turns out to be decreased with fibre orientation. Dimension of crystallite size D hkl estimated in the perpendicular mounting D_{hkl}^{ \\bot } is more as compared to that of the parallel mounting D_{hkl}^{{^{allel } }}. The smallest crystallite sizes observed in both parallel and perpendicular mounting are 18.78 and 30.78 Å respectively. It is expected that the present study may help to analyse the X-ray diffraction of fibre materials in general and natural fibres in particular.

  16. Fibre optic communication key devices

    CERN Document Server

    Grote, Norbert

    2017-01-01

    The book gives an in-depth description of key devices of current and next generation fibre optic communication networks. Devices treated include semiconductor lasers, optical amplifiers, modulators, wavelength filters and other passives, detectors, all-optical switches, but relevant properties of optical fibres and network aspects are included as well. The presentations include the physical principles underlying the various devices, technologies used for their realization, typical performance characteristics and limitations, but development trends towards more advanced components are also illustrated. This new edition of a successful book was expanded and updated extensively. The new edition covers among others lasers for optical communication, optical switches, hybrid integration, monolithic integration and silicon photonics. The main focus is on Indium phosphide-based structures but silicon photonics is included as well. The book covers relevant principles, state-of-the-art implementations, status of curren...

  17. InGaN/GaN DFB laser diodes at 434 nm with deeply etched sidewall gratings

    Science.gov (United States)

    Slight, Thomas J.; Odedina, Opeoluwa; Meredith, Wyn; Docherty, Kevin E.; Kelly, Anthony E.

    2016-02-01

    We report on deeply etched sidewall grating DFB lasers in the InGaN/GaN material system emitting at a single wavelength around 434 nm. GaN lasers have a wide range of applications in communications, displays and storage. The availability of a single wavelength device with a good side mode suppression ratio (SMSR) would allow further applications to be addressed such as sources for laser cooling and Fraunhofer line operation for solar background free communications. Sidewall etched gratings have the advantage of fabrication with no need for overgrowth and have been demonstrated in a range of other material systems and wavelengths. Importantly for GaN based devices, this design has the potential to minimise fabrication induced damage to the epi structure. We investigated two laser designs, one with 80 % duty-cycle 3rd order gratings and another with 39th order partial gratings. Simulation of the 2D waveguide sections was carried out to find the optimal grating width. For fabrication, the laser ridge and gratings were patterned in a single step using electron beam lithography and ICP etched to a depth of 500 nm. Contact metal was deposited and the sample thinned and cleaved into 1 mm long cavities. The as-cleaved 3rd order lasers emit in the pulsed regime with a SMSR of 20 dB and a peak single-mode output power of 40 mW. The output power is similar to that of parallel processed FP lasers. The 39th order lasers also exhibit narrow spectral width at an output power of 10 mW.

  18. Electrospun cerium nitrate/polymer composite fibres:synthesis, characterization and fibre-division model

    Institute of Scientific and Technical Information of China (English)

    Li Meng-Meng; Long Yun-Ze; Yin Hong-Xing; Zhang Zhi-Ming

    2011-01-01

    Cerium (III)nitrate/poly(vinylpyrrolidone)(Ce(NO3)3/PVP)composite fibres have been prepared by electrospinning. After calcining the composite fibres in air at 500℃, CeO2 nanowires were obtained. The characterizations of the as-spun composite fibres and resultant nanowires have been carried out by a scanning electron microscope (SEM),an infrared spectrometer, an x-ray diffractometer and a fluorescence spectrophotometer. Interestingly, some unusual ribbon-like or twin fibres were observed besides the common fibres with circular or elliptic cross sections. We developed a fibre-division model resulting from Coulomb repulsion and solvent vaporization to interpret the formation of the ribbona or twin fibres, which has been confirmed by the SEM studies. Our results also indicate that the formation of the ribbons or twin fibres is less dependent on operation voltage and work distance.

  19. Orientation distribution of fibres in a channel flow of fibre suspension

    Institute of Scientific and Technical Information of China (English)

    Lin Jian-Zhong; Li Jun; Zhang Wei-Feng

    2005-01-01

    The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.

  20. Interfacial Adhesion Characteristics of Kenaf Fibres Subjected to Different Polymer Matrices and Fibre Treatments

    Directory of Open Access Journals (Sweden)

    Umar Nirmal

    2014-01-01

    Full Text Available This study is aimed at determining the interfacial adhesion strength (IAS of kenaf fibres using different chemical treatments in hydrochloric (HCl and sodium hydroxide (NaOH with different concentrations. Single fibre pullout tests (SFPT were carried out for both untreated and treated fibres partially embedded into three different polymer matrices; polyester, epoxy, and polyurethane (PU as reinforcement blocks and tested under dry loading conditions. The study revealed that kenaf fibres treated with 6% NaOH subjected to polyester, epoxy, and PU matrices exhibits excellent IAS while poor in acidic treatment. The effect of SFPT results was mainly attributed to chemical composition of the fibres, types of fibre treatments, and variation in resin viscosities. By scanning electron microscopy examination of the material failure morphology, the fibres experienced brittle and ductile fibre breakage mechanisms after treatment with acidic and alkaline solutions.

  1. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish......Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...

  2. Muscle fibre type and aetiology of obesity.

    Science.gov (United States)

    Wade, A J; Marbut, M M; Round, J M

    1990-04-07

    Proportions of slow (type 1) muscle fibres of the vastus lateralis and percentage body fat were measured in 11 healthy sedentary men. The proportion of slow muscle fibres was inversely related to fatness; at least 40% of the variability in fatness may be related to variation in muscle fibre type. Metabolic evidence in 50 men, provided by the respiratory exchange ratio (RER) during cycle ergometry, indicated that fatter men (or, in the subset of 11 men, those with a low proportion of slow muscle fibres) combusted less fat during work at 100 W than did lean men (or those with a high proportion of slow fibres). The effects of fitness and of body size were excluded in the analysis. The evidence supports the hypothesis that muscle fibre type is an aetiological factor for obesity.

  3. Co-modulation of WDM-FDM WiMAX-FM and IEEE802.11ac signals by DFB-LD and MZM

    Science.gov (United States)

    Teruya, Miku; Chinen, Koyu

    2017-07-01

    We have investigated how wavelength spacing and frequency spacing in WDM (Wavelength Division Multiplexing) and FDM (Frequency Division Multiplexing) using direct modulation lasers (DML) and external modulators of Mach-Zehnder Modulator (MZM) affect optical and electrical interferences. Two signals of 4.8GHz-64QAM-5MHzBW WiMAX and 4.7GHz-32MHzBW FM were directly modulated with uncooled 1550nm DFB-LDs, and 5GHz-256QAM-80MHzBW IEEE802.11ac signal was modulated on the combined optical signals of WiMAX and FM at an MZM. Change in RCE of the WiMAX signal and EVM of the IEEE 802.11ac signal were measured when the wavelength spacing between two DFB-LDs was varied. When the wavelength spacing was larger than 0.05 nm and the ratio of peak to bottom of optical power was larger than 30 dB, the RCE of WiMAX signal was decreased to lower than -20dB. The WDM using directly modulated DFB-LDs and MZM was realized, when the wavelength spacing was larger than 0.1 nm and the peak to bottom ratio of optical power was larger than 60 dB, since the EVM of IEEE802.11ac signal was decreased to around -30dB. The FDM with the same configuration as that of the WDM was realized, when the frequency spacing was larger than a half of the sum of the BWs of WiMAX and FM signals, as the RCE of WiMAX signal decreased to lower than -35 dB and the EVM of IEEE802.11ac signal decreased to around -30dB.

  4. Continuous jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate

    Indian Academy of Sciences (India)

    B B Verma

    2009-12-01

    Plastic bags create a serious environmental problem. The proposed jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate may help to combat the war against this pollutant to certain extent. The paper laminate, without reinforcement fibre, exhibited a few fold superiority in tensile properties than single paper strip. The studies further show that an appreciable improvement in tensile properties can be achieved by introducing continuous jute fibre in paper laminates.

  5. Polymeric Optical Fibres for Biomedical Sensing

    OpenAIRE

    Krehel, M P

    2014-01-01

    In this thesis we focus on the integration of optical fibres in textiles to create wearable sensing systems. In the introduction (Chapter 3) we describe the basics of light guiding in optical fibres and methods of lateral light coupling. Subsequently, a literature review and motivation are presented. Afterwards two main parts can be differentiated. In the first one (Chapters 4, 5) a new method of continuous extrusion of optical fibres and their medical sensing application using photoplethysmo...

  6. THERMAL AND ENVIRONMENTAL EFFECTS ON CERAMIC FIBRES

    OpenAIRE

    Karlsson, S.; Lundberg, R.; Carlsson, R.

    1986-01-01

    Fibre insulations in kilns in the ceramic industry were investigated. Cristobalite and mullite are the main crystalline phases found in Al2O3-SiO2 fibres. The amount of the crystalline phases formed depends on the chemical composition and firing temperature. Condensation of ZnO-vapours from the glaze and formation of ZnAl2O4 were found in a Saffil fibre at a temperature of 930°C.

  7. Tandem electro-absorption modulators integrated with DFB laser by ultra-low-pressure selective-area-growth MOCVD for 10 GHz optical short-pulse generation

    Science.gov (United States)

    Zhao, Q.; Pan, J. Q.; Zhang, J.; Zhou, G. T.; Wu, J.; Wang, L. F.; Wang, W.

    2005-11-01

    A novel device of tandem multiple quantum wells (MQWs) electroabsorption modulators (EAMs) monolithically integrated with DFB laser is fabricated by ultra-low-pressure (22 mbar) selective area growth (SAG) MOCVD technique. Experimental results exhibit superior device characteristics with low threshold of 19 mA, output light power of 4.5 mW, and over 20 dB extinction ratio when coupled into a single mode fiber. Moreover, over 10 GHz modulation bandwidth is developed with a driving voltage of 2 V. Using this sinusoidal voltage driven integrated device, 10GHz repetition rate pulse with a width of 13.7 ps without any compression elements is obtained.

  8. Monolithic integration on InP of a Wannier Stark modulator with a strained MQW DFB 1.55-micron laser

    Science.gov (United States)

    Allovon, Michel; Fouchet, Sylvie; Harmand, Jean-Christophe; Ougazzaden, Abdallah; Rose, Benoit; Gloukhian, Andre; Devaux, Fabrice

    1995-02-01

    We present the technical approach and the preliminary device results on the first integration of a Wannier Stark (WS) electroabsorption (EA) modulator with a DFB laser on InP. The WS modulator active layer consists of a lattice matched InGaAs-InAlAs superlattice (SL) grown by solid source MBE (Molecular Beam Epitaxy). It is butt-coupled to a laser grown by AP-MOVPE whose active layer includes a strained InGaAsP-InGaAsP MQW stack. Device results cover static performances of integrated lasers and modulators, and measurements of high frequency characteristics (small signal bandwidth and 10 Gb/s eye diagram).

  9. Monolithic integration of an InGaAsP InP strained DFB laser and an electroabsorption modulator by ultra-low-pressure selective-area-growth MOCVD

    Science.gov (United States)

    Zhao, Q.; Pan, J. Q.; Zhou, F.; Wang, B. J.; Wang, L. F.; Wang, W.

    2005-06-01

    The design and basic characteristics of a strained InGaAsP-InP multiple-quantum-well (MQW) DFB laser monolithically integrated with an electroabsorption modulator (EAM) by ultra-low-pressure (22 mbar) selective-area-growth (SAG) MOCVD are presented. A fundamental study of the controllability and the applicability of band-gap energy by using the SAG method is performed. A large band-gap photoluminescence wavelength shift of 88 nm was obtained with a small mask width variation (0-30 µm). The technique is then applied to fabricate a high performance strained MQW EAM integrated with a DFB laser. The threshold current of 26 mA at CW operation of the device with DFB laser length of 300 µm and EAM length of 150 µm has been realized at a modulator bias of 0 V. The devices also exhibit 15 dB on/off ratio at an applied bias voltage of 5 V.

  10. A novel photonic crystal fibre switch

    DEFF Research Database (Denmark)

    Alkeskjold, Thomas Tanggaard; Hermann, D.S.; Broeng, Jes

    2003-01-01

    A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB.......A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB....

  11. Abaca fibre reinforced PP composites and comparison with jute and flax fibre PP composites

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available Abaca fibre reinforced PP composites were fabricated with different fibre loadings (20, 30, 40, 50wt% and in some cases 35 and 45 wt%. Flax and jute fibre reinforced PP composites were also fabricated with 30 wt% fibre loading. The mechanical properties, odour emission and structure properties were investigated for those composites. Tensile, flexural and Charpy impact strengths were found to increase for fibre loadings up to 40 wt% and then decreased. Falling weight impact tests were also carried out and the same tendency was observed. Owing to the addition of coupling agent (maleated polypropylene -MAH-PP, the tensile, flexural and falling weight impact properties were found to increase in between 30 to 80% for different fibre loadings. When comparing jute and flax fibre composites with abaca fibre composites, jute fibre composites provided best tensile properties but abaca fibre polypropylene composites were shown to provide best notch Charpy and falling weight impact properties. Odours released by flax fibre composites were smaller than jute and abaca fibre composites.

  12. A validation of the fibre orientation and fibre length attrition prediction for long fibre-reinforced thermoplastics

    Science.gov (United States)

    Hopmann, Ch.; Weber, M.; van Haag, J.; Schöngart, M.

    2015-05-01

    To improve the mechanical performance of polymeric parts, fibre reinforcement has established in industrial applications during the last decades. Next to the widely used Short Fibre-reinforced Thermoplastics (SFT) the use of Long Fibre-reinforced Thermoplastics (LFT) is increasingly growing. Especially for non-polar polymeric matrices like polypropylene (PP), longer fibres can significantly improve the mechanical performance. As with every kind of discontinuous fibre reinforcement the fibre orientations (FO) show a high impact on the mechanical properties. On the contrary to SFT where the local fibre length distribution (FLD) can be often neglected, for LFT the FLD show a high impact on the material's properties and has to be taken into account in equal measure to the FOD. Recently numerical models are available in commercial filling simulation software and allow predicting both the local FOD and FLD in LFT parts. The aim of this paper is to compare i.) the FOD results and ii) the FLD results from available orientation- and fibre length attrition-models to those obtained from experimental data. The investigations are conducted by the use of different injection moulded specimens made from long glass fibre reinforced PP. In order to determine the FOD, selected part sections are examined by means of Computed Tomographic (CT) analyses. The fully three dimensional measurement of the FOD is then performed by digital image processing using grey scale correlation. The FLD results are also obtained by using digital image processing after a thermal pyrolytic separation of the polymeric matrix from the fibres. Further the FOD and the FLD are predicted by using a reduced strain closure (RSC) as well as an anisotropic rotary diffusion - reduced strain closure model (ARD-RSC) and Phelps-Tucker fibre length attrition model implemented in the commercial filling software Moldflow, Autodesk Inc., San Rafael, CA, USA.

  13. A validation of the fibre orientation and fibre length attrition prediction for long fibre-reinforced thermoplastics

    Energy Technology Data Exchange (ETDEWEB)

    Hopmann, Ch.; Weber, M.; Haag, J. van; Schöngart, M. [Institute of Plastics Processing (IKV) at RWTH Aachen University, Pontstr. 49, 52062 Aachen (Germany)

    2015-05-22

    To improve the mechanical performance of polymeric parts, fibre reinforcement has established in industrial applications during the last decades. Next to the widely used Short Fibre-reinforced Thermoplastics (SFT) the use of Long Fibre-reinforced Thermoplastics (LFT) is increasingly growing. Especially for non-polar polymeric matrices like polypropylene (PP), longer fibres can significantly improve the mechanical performance. As with every kind of discontinuous fibre reinforcement the fibre orientations (FO) show a high impact on the mechanical properties. On the contrary to SFT where the local fibre length distribution (FLD) can be often neglected, for LFT the FLD show a high impact on the material’s properties and has to be taken into account in equal measure to the FOD. Recently numerical models are available in commercial filling simulation software and allow predicting both the local FOD and FLD in LFT parts. The aim of this paper is to compare i.) the FOD results and ii) the FLD results from available orientation- and fibre length attrition-models to those obtained from experimental data. The investigations are conducted by the use of different injection moulded specimens made from long glass fibre reinforced PP. In order to determine the FOD, selected part sections are examined by means of Computed Tomographic (CT) analyses. The fully three dimensional measurement of the FOD is then performed by digital image processing using grey scale correlation. The FLD results are also obtained by using digital image processing after a thermal pyrolytic separation of the polymeric matrix from the fibres. Further the FOD and the FLD are predicted by using a reduced strain closure (RSC) as well as an anisotropic rotary diffusion - reduced strain closure model (ARD-RSC) and Phelps-Tucker fibre length attrition model implemented in the commercial filling software Moldflow, Autodesk Inc., San Rafael, CA, USA.

  14. Surface treated polypropylene (PP) fibres for reinforced concrete

    Energy Technology Data Exchange (ETDEWEB)

    López-Buendía, Angel M., E-mail: buendia@uv.es [AIDICO Technological Institute of Construction, Benjamin Franklin 17, 46380 Paterna, Valencia (Spain); Romero-Sánchez, María Dolores [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain); Climent, Verónica [Lafarge Cementos, Polígono Sepes, Isaac Newton s/n, 46500 Sagunto, Valencia (Spain); Guillem, Celia [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain)

    2013-12-15

    Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

  15. Electrical Characterization of Silicon Cores from Glass-Cladded Fibres

    OpenAIRE

    Lapointe, Kyle

    2014-01-01

    Semiconductor core fibres represent an emerging technology with potential applications in many areas, including photovoltaics and optical transmission. Recent advances in fibre manufacturing techniques has allowed long, continuous silicon core fibres to be produced in commercial draw towers. The effect of the molten core fibre fabrication method on the electrical properties of silicon cores from glass-clad fibres have been studied. Fibres with core diameters ranging from 60 to 300 µm wer...

  16. Postponed sowing does not alter the fibre/wood ratio or fibre extractability of fibre hemp (Cannabis sativa)

    NARCIS (Netherlands)

    Westerhuis, W.; Struik, P.C.; Dam, van J.E.G.; Stomph, T.J.

    2009-01-01

    Because hemp is a short-day plant, postponing the sowing date might be a suitable strategy to obtain shorter and smaller plants around flowering, when primary fibres are 'ripe' enough to be harvested. Smaller plants can be processed on existing flax scutching and hackling lines and might have fibre

  17. Simulation of complex phenomena in optical fibres

    Science.gov (United States)

    Allington-Smith, Jeremy; Murray, Graham; Lemke, Ulrike

    2012-12-01

    Optical fibres are essential for many types of highly multiplexed and precision spectroscopy. The success of the new generation of multifibre instruments under construction to investigate fundamental problems in cosmology, such as the nature of dark energy, requires accurate modellization of the fibre system to achieve their signal-to-noise ratio (SNR) goals. Despite their simple construction, fibres exhibit unexpected behaviour including non-conservation of etendue (focal ratio degradation, FRD) and modal noise. Furthermore, new fibre geometries (non-circular or tapered) have become available to improve the scrambling properties that, together with modal noise, limit the achievable SNR in precision spectroscopy. These issues have often been addressed by extensive tests on candidate fibres and their terminations, but these are difficult and time-consuming. Modelling by ray tracing and wave analysis is possible with commercial software packages, but these do not address the more complex features, in particular FRD. We use a phase-tracking ray-tracing method to provide a practical description of FRD derived from our previous experimental work on circular fibres and apply it to non-standard fibres. This allows the relationship between scrambling and FRD to be quantified for the first time. We find that scrambling primarily affects the shape of the near-field pattern but has negligible effect on the barycentre. FRD helps to homogenize the near-field pattern but does not make it completely uniform. Fibres with polygonal cross-section improve scrambling without amplifying the FRD. Elliptical fibres, in conjunction with tapering, may offer an efficient means of image slicing to improve the product of resolving power and throughput, but the result is sensitive to the details of illumination. We also investigated the performance of fibres close to the limiting numerical aperture since this may affect the uniformity of the SNR for some prime focus fibre instrumentation.

  18. Multicore optical fibre and fibre-optic delay line based on it

    Science.gov (United States)

    Egorova, O. N.; Astapovich, M. S.; Belkin, M. E.; Semjonov, S. L.

    2016-12-01

    The first switchable fibre-optic delay line based on a 1300-{\\text{m}}-long multicore optical fibre has been fabricated and investigated. We have obtained signal delay times of up to 45 \\unicode{956}{\\text{s}} at 6.43-\\unicode{956}{\\text{s}} intervals. Sequential signal propagation through the cores of the multicore optical fibre makes it possible to reduce the fibre length necessary for obtaining a predetermined delay time, which is important for reducing the weight and dimensions of devices based on the use of fibre-optic delay lines.

  19. Polarisation effects in twin-core fibre: Application for mode locking in a fibre laser

    Energy Technology Data Exchange (ETDEWEB)

    Lobach, I A; Kablukov, S I; Podivilov, Evgenii V; Babin, Sergei A; Apolonski, A A

    2012-09-30

    We report the first measurements of the longitudinal power distribution in a twin-core optical fibre at different input light polarisations. Experimental evidence is presented that, because of the difference in birefringence between the cores, the power in them depends on which core the beam is launched into. Experimental data are interpreted in terms of a modified polarisation model for mode coupling in twin-core fibres which takes into account the birefringence of the cores. In addition, we demonstrate for the first time the use of the polarisation properties of a twincore fibre for mode locking in a fibre laser. (optical fibres, lasers and amplifiers. properties and applications)

  20. Investigation on effect of fibre hybridization and orientation on mechanical behaviour of natural fibre epoxy composite

    Indian Academy of Sciences (India)

    P KALIAPPAN; R KESAVAN; B VIJAYA RAMNATH

    2017-08-01

    Nowadays bio fibre composites play a vital role by replacing conventional materials used in automotive andaerospace industries owing to their high strength to weight ratio, biodegradability and ease of production. This paper aimsto find the effect of fibre hybridization and orientation on mechanical behaviour of composite fabricated with neem, abacafibres and epoxy resin. Here, three varieties of composites are fabricated namely, composite 1 which consists of abaca fibreand glass fibre, composite 2, which consists of neem fibre and glass fibre, whereas composite 3 consists of abaca, neem fibresand glass fibres. In all the above three varieties, fibres are arranged in three types of orientations namely, horizontal (type I),vertical (type II) and 45$^{\\circ}$ inclination (type III). The result shows that composites made up of abaca and neem fibres withinclined orientation (45$^{\\circ}$) have better mechanical properties when compared with other types of composites. In addition, morphological analysis is carried out using scanning electron microscope to know the fibre distribution, fibre pull out, fibre breakage and crack propagation on tested composites.

  1. 1.5-μm and 10-Gb s-1 etched mesa buried heterostructure DFB-LD for datacenter networks

    Science.gov (United States)

    Kwon, Oh Kee; Lee, Chul Wook; Leem, Young Ahn; Kim, Ki Soo; Oh, Su Hwan; Nam, Eun Soo

    2015-10-01

    We report a 1.5 μm and 10 Gb s-1 etched mesa buried heterostructure λ/4-shifted distributed feedback laser diode (DFB-LD) for the low-cost application of WDM-based datacenter networks. To reduce the threshold current and improve the modulation bandwidth in a conventional p-/n-/p-InP current blocking structure, a thin undoped-InP (u-InP) layer was inserted between the side walls of the active region and the p-InP layer (i.e., a u-/p-/n-/p-InP structure), and the region containing the active region and the current blocking structures was etched in a mesa form (i.e., an etched mesa). From this work, it was found that a 300 μm long anti-reflection (AR)-AR DFB-LD with a mesa width of 8 μm is reduced by about 25% while a side mode suppression ratio is >50 dB and a 3 dB bandwidth is >10 GHz at a current of 40 mA; in addition, it shows a clear eye-opening with a dynamic extinction ratio of >4.5 dB at 10 Gb s-1, and a power penalty of transmission.

  2. InGaAs/InGaAsP MQW electroabsorption modulator integrated with a DFB laser fabricated by band-gap energy control selective area MOCVD

    Science.gov (United States)

    Aoki, Masahiro; Suzuki, Makoto; Sano, Hirohisa; Kawano, Toshihiro; Ido, Tatemi; Taniwatari, Tsuyoshi; Uomi, Kazuhisa; Takai, Atsushi

    1993-06-01

    Fabrication and basic characteristics of a new structure InGaAs/InGaAsP (MQW) electroabsorption modulator integrated with a distributed feedback (DFB) laser are presented. First, a fundamental study was performed on the applicability of the InGaAs/InGaAsP MQW structure to an electroabsorption-type modulator. We have experimentally demonstrated both the efficient attenuation, the small hole pileup and small chirp characteristics of a discrete modular based on this MQW structure. We also made a study of the controllability of in-plane band-gap energy by the use of selective area metal-organic chemical vapor deposition aimed at one-step growth integration of modulators and lasers. We demonstrated a sufficient range for controllable quantum energy level and high quality of the selectively grown MQW lasers. By using this technique, the modulator was monolithically integrated with a same-material MQW DFB laser. Using a low capacitance semi-insulating buried-hetero structure, we achieved over 14-GHz modulation under high-light-output operations up to +10 dBm.

  3. Influence of fibre volume fraction and temperature on fatigue life of glass fibre reinforced plastics

    Directory of Open Access Journals (Sweden)

    Konrad Wegener

    2016-07-01

    Full Text Available The influence of fibre volume fraction and temperature on fatigue life of continuous glass fibre reinforced plastics is investigated in detail. The physical causes of the two effects on the slope of the S-N-curve in fibre direction at R = 0.1 are researched and can be explained with help of micrographs. A new phenomenological approach is presented to model both effects in fibre dominated laminates with different stacking sequences using only the static ultimate strength as an input. Static and fatigue tests of different layups and fibre volume fractions are performed at different temperatures to validate the fatigue life predictions. Additionally it is derived that there is an optimal fibre volume fraction regarding a minimum damage sum. This fibre volume fraction is dependent on a given loading spectra and can be calculated using the phenomenological model.

  4. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury, high value-added end of the market, notably the apparel market, being renowned for their special...

  5. low pump power photonic crystal fibre amplifiers

    DEFF Research Database (Denmark)

    Hougaard, Kristian G.; Broeng, Jes; Bjarklev, Anders Overgaard

    2003-01-01

    Designs of low pump power optical amplifiers, based on photonic crystal fibres are presented. The potential of these fibre amplifiers is investigated, and it is demonstrated that such amplifiers may deliver gains of more than 15 dB at 1550 nm with less than 1 mW of optical pump power....

  6. The development of fibre optic microbend sensors

    NARCIS (Netherlands)

    Horsthuis, W.H.G.; Fluitman, J.H.J.

    1983-01-01

    Investigations concerning the development of a fibre optic pressure sensor are reported. The phenomenon of light power attenuation in a periodically deformed graded index fibre has been studied theoretically. It appears that available theories are not suited to describe this attenuation process in t

  7. Multifunctional Carbon Fibre Tapes for Automotive Composites

    Science.gov (United States)

    Koncherry, V.; Potluri, P.; Fernando, A.

    2016-11-01

    Cabon fibre composites are used where mechanical performance such as strength, stiffness and impact properties at low density is a critical parameter for engineering applications. Carbon fibre flat tape is one material which is traditionally used to manufacture three-dimensional composites in this area. Modifying the carbon fibre tape to incorporate other functions such as stealth, electromagnetic interference, shielding, de-icing, self-repair, energy storage, allows us to create multi-functional carbon fibre tape. Researchers have been developing such material and the technology for their manufacture in order to produce multifunctional carbon fibre based components more economically and efficiently. This paper presents the manufacturing process of a metallised carbon fibre material for a chopped fibre preforming process that uses electromagnets for preforming instead of traditional suction airflow fibre deposition. In addition, the paper further presents mechanical and magneto-static modelling that is carried out to investigate the bending properties of the material produced and its suitability for creating 3D preforms.

  8. Dispersion properties of photonic Bandgap Fibres

    DEFF Research Database (Denmark)

    Broeng, Jes; Barkou, Stig Eigil; Søndergaard, Thomas

    1999-01-01

    Dispersion properties of new low-index core photonic crystal fibres are presented. Both wideband nearzero despersion and very large dispersion is shown possible in the 1550 nm wavelength range.......Dispersion properties of new low-index core photonic crystal fibres are presented. Both wideband nearzero despersion and very large dispersion is shown possible in the 1550 nm wavelength range....

  9. Selective filling of Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Noordegraaf, Danny; Sørensen, Thorkild

    2005-01-01

    A model for calculating the time necessary for filling one or more specific holes in a photonic crystal fibre is made. This model is verified for water, and its enabling potential is illustrated by a polymer application. Selective filling of the core in an air-guide photonic crystal fibre...

  10. Strength variability of single flax fibres

    DEFF Research Database (Denmark)

    Aslan, Mustafa; Chinga-Carrasco, G.; Sørensen, Bent F.

    2011-01-01

    (linear and nonlinear) of the fibres are found to be correlated with the amount of defects. The linear stress–strain curves tend to show a higher tensile strength, a higher Young’s modulus, and a lower strain to failure than the nonlinear curves. Finally, the fibres are found to fracture by a complex...

  11. Thermally induced structural changes in Nomex fibres

    Indian Academy of Sciences (India)

    Anjana Jain; Kalyani Vijayan

    2002-08-01

    Thermally aged Nomex fibres manifest several residual effects viz. reduction in X-ray crystallinity, weight loss and deterioration in tensile characteristics. Surface damages in the form of longitudinal openings, holes, material deposits etc have also been observed. Based on the data from thermally exposed fibres, the time needed for states of zero tensile strength and modulus have been predicted.

  12. Fibre optic cables for the ALICE experiment

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    These thin fibres will transmit the signal received in detectors at the ALICE experiment when it starts up with the LHC in 2008. The analogue signals produced in the detectors are first converted into digital pulse, which are transported in light down such fibres. Computers then read this digital signal to produce the final set of data.

  13. Cotton fibre cross-section properties

    Science.gov (United States)

    From a structural perspective the cotton fibre is a singularly discrete, elongated plant cell with no junctions or inter-cellular boundaries. Its form in nature is essentially unadulterated from the field to the spinning mill where its cross-section properties, as for any textile fibre, are central ...

  14. Fibre positioning algorithms for the WEAVE spectrograph

    NARCIS (Netherlands)

    Terrett, David L.; Lewis, Ian J.; Dalton, Gavin; Abrams, Don Carlos; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Middleton, Kevin; Trager, Scott C.

    2014-01-01

    WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. It is a multi-object "pick and place" fibre fed spectrograph with more than one thousand fibres, similar in concept to the Australian Astronomical Observ

  15. Winding of fibre composites; Vikling af fiberkompositter

    Energy Technology Data Exchange (ETDEWEB)

    Lystrup, Aage

    2006-01-01

    Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

  16. Selective filling of Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Noordegraaf, Danny; Sørensen, Thorkild

    2005-01-01

    A model for calculating the time necessary for filling one or more specific holes in a photonic crystal fibre is made. This model is verified for water, and its enabling potential is illustrated by a polymer application. Selective filling of the core in an air-guide photonic crystal fibre is demo...

  17. Development of the fibres of MOONS

    Science.gov (United States)

    Guinouard, Isabelle; Lee, David; Schnetler, Hermine; Taylor, William; Amans, Jean-Philippe; Montgomery, David; Oliva, Ernesto

    2014-07-01

    MOONS will exploit the full 500 square arcmin field of view offered by the Nasmyth focus of the Very Large Telescope and will be equipped with two identical triple arm cryogenic spectrographs covering the wavelength range 0.8 - 1.8 μm, with a multiplex capability of approximately 1000 fibres. Each triple arm spectrograph will produce spectra for half of the targets simultaneously. The system will have both a medium resolution (R~4000-6000) mode and a high resolution (R~20000) mode. The fibres are used to pick off each sub field of 1.05 arcseconds and are used to transport the light from the instrument focal plane to the two spectrographs. Each fibre has a microlens to focus the beam into the fibre at a relative fast focal ratio of F/3.65 to reduce the Focal Ratio Degradation (FRD). This paper presents the overall design of the fibre system and describes the specific developments required to optimise its performance. The design of the fibre input optics, the choice of the fibre connector, and the layout of the slit end are described. The results of preliminary tests to measure the effect of twisting on the FRD performance of prototype fibres are also discussed.

  18. Innovations with protein nano-fibres

    NARCIS (Netherlands)

    Linden, van der E.

    2006-01-01

    Proteins in solution can form objects of various shapes. One fascinating possibility is the formation of fibres with a length up to micrometers, but with a thickness of a few nanometers, therefore referring to them as nano-fibres. Many proteins show this behaviour under the appropriate conditions. G

  19. Winding of fibre composites; Vikling af fiberkompositter

    Energy Technology Data Exchange (ETDEWEB)

    Lystrup, Aage

    2006-01-01

    Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

  20. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Nielsen, Laila

    1997-01-01

    (capillary water uptake) is used, involving an in-situ method and a laboratory method. Three different concrete qualities as well as steel fibres (ZP) and polypropylene fibres (PP) are used. Results of the durability tests on cracked FRC-beams are compared to results for uncracked FRC-beams and beams without...

  1. Image analysis of insulation mineral fibres.

    Science.gov (United States)

    Talbot, H; Lee, T; Jeulin, D; Hanton, D; Hobbs, L W

    2000-12-01

    We present two methods for measuring the diameter and length of man-made vitreous fibres based on the automated image analysis of scanning electron microscopy images. The fibres we want to measure are used in materials such as glass wool, which in turn are used for thermal and acoustic insulation. The measurement of the diameters and lengths of these fibres is used by the glass wool industry for quality control purposes. To obtain reliable quality estimators, the measurement of several hundred images is necessary. These measurements are usually obtained manually by operators. Manual measurements, although reliable when performed by skilled operators, are slow due to the need for the operators to rest often to retain their ability to spot faint fibres on noisy backgrounds. Moreover, the task of measuring thousands of fibres every day, even with the help of semi-automated image analysis systems, is dull and repetitive. The need for an automated procedure which could replace manual measurements is quite real. For each of the two methods that we propose to accomplish this task, we present the sample preparation, the microscope setting and the image analysis algorithms used for the segmentation of the fibres and for their measurement. We also show how a statistical analysis of the results can alleviate most measurement biases, and how we can estimate the true distribution of fibre lengths by diameter class by measuring only the lengths of the fibres visible in the field of view.

  2. Interfaces between a fibre and its matrix

    Science.gov (United States)

    Lilholt, H.; Sørensen, B. F.

    2017-07-01

    The interface between a fibre and its matrix represents an important element in the characterization and exploitation of composite materials. Both theoretical models and analyses of experimental data have been presented in the literature since modern composite were developed and many experiments have been performed. A large volume of results for a wide range of composite systems exists, but rather little comparison and potential consistency have been reached for fibres and/or for matrices. Recently a materials mechanics approach has been presented to describe the interface by three parameters, the interfacial energy [J/m2], the interfacial frictional shear stress [MPa] and the mismatch strain [-] between fibre and matrix. The model has been used for the different modes of fibre pull-out and fibre fragmentation. In this paper it is demonstrated that the governing equations for the experimental parameters (applied load, debond length and relative fibre/matrix displacement) are rather similar for these test modes. A simplified analysis allows the direct determination of the three interface parameters from two plots for the experimental data. The complete analysis is demonstrated for steel fibres in polyester matrix. The analysis of existing experimental literature data is demonstrated for steel fibres in epoxy matrix and for tungsten wires in copper matrix. These latter incomplete analyses show that some results can be obtained even if all three experimental parameters are not recorded.

  3. Microstructural characterization of stone wool fibre network

    DEFF Research Database (Denmark)

    Chapelle, Lucie; Brøndsted, Povl; Kusano, Yukihiro;

    2014-01-01

    Understanding the mechanical properties of fibrous network as complex as stone wool materials requires a relevant description of their microstructure and architecture. In this study, different methods have been proposed to characterize the fibre orientation, diameter and length of fibres as well...

  4. Insertion of optic fibre for CMS

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    The MicroJET system uses high pressure to carefully put the optical fibres into their protective tubes. These fibres are vital for rapid data transfer, but are also very delicate and, if damanged, may not work at the required efficiency. Similiar methods are used to install cables for the telecommunications industry.

  5. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  6. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.;

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  7. Fibre Distribution in Friction-spun Yarns

    Institute of Scientific and Technical Information of China (English)

    Eric Oyondi Nganyi; YU Chong-wen

    2006-01-01

    According to the yarn forming characteristics in friction spinning, the arrangement of fed sliver is designed, to get the desired fiber distribution in the resultant yarn. On the base of that, the relation between the theoretical fibre distribution and the actual fibre distribution is analyzed by use of electron microscope.

  8. Metal-coated Bragg grating reflecting fibre

    Science.gov (United States)

    Chamorovskiy, Yu. K.; Butov, O. V.; Kolosovskiy, A. O.; Popov, S. M.; Voloshin, V. V.; Vorob'ev, I. L.; Vyatkin, M. Yu.

    2017-03-01

    High-temperature optical fibres (OF) with fibre Bragg gratings (FBG) arrays written over a long length and in-line metal coating have been made for the first time. The optical parameters of the FBG arrays were tested by the optical frequency domain reflectometer (OFDR) method in a wide temperature range, demonstrating no degradation in reflection at heating up to 600 °C for a fibre with Al coating. The mechanical strength of the developed fibre was practically the same as "ordinary" OF with similar coating, showing the absence of the influence of FBG writing process on fibre strength. Further experiments are necessary to evaluate the possibility of further increases in the operational temperature range.

  9. Simulation of complex phenomena in optical fibres

    CERN Document Server

    Allington-Smith, Jeremy; Lemke, Ulrike

    2012-01-01

    Optical fibres are essential for many types of highly-multiplexed and precision spectroscopy. The success of the new generation of multifibre instruments under construction to investigate fundamental problems in cosmology, such as the nature of dark energy, requires accurate modellisation of the fibre system to achieve their signal-to-noise goals. Despite their simple construction, fibres exhibit unexpected behaviour including non-conservation of Etendue (Focal Ratio Degradation; FRD) and modal noise. Furthermore, new fibre geometries (non-circular or tapered) have become available to improve the scrambling properties that, together with modal noise, limit the achievable SNR in precision spectroscopy. These issues have often been addressed by extensive tests on candidate fibres and their terminations but these are difficult and time-consuming. Modelling by ray-tracing and wave analysis is possible with commercial software packages but these do not address the more complex features, in particular FRD. We use a...

  10. Review article: dietary fibre-microbiota interactions.

    Science.gov (United States)

    Simpson, H L; Campbell, B J

    2015-07-01

    Application of modern rapid DNA sequencing technology has transformed our understanding of the gut microbiota. Diet, in particular plant-based fibre, appears critical in influencing the composition and metabolic activity of the microbiome, determining levels of short-chain fatty acids (SCFAs) important for intestinal health. To assess current epidemiological, experimental and clinical evidence of how long-term and short-term alterations in dietary fibre intake impact on the microbiome and metabolome. A Medline search including items 'intestinal microbiota', 'nutrition', 'diet', 'dietary fibre', 'SCFAs' and 'prebiotic effect' was performed. Studies found evidence of fibre-influenced differences in the microbiome and metabolome as a consequence of habitual diet, and of long-term or short-term intervention (in both animals and humans). Agrarian diets high in fruit/legume fibre are associated with greater microbial diversity and a predominance of Prevotella over Bacteroides. 'Western'-style diets, high in fat/sugar, low in fibre, decrease beneficial Firmicutes that metabolise dietary plant-derived polysaccharides to SCFAs and increase mucosa-associated Proteobacteria (including enteric pathogens). Short-term diets can also have major effects, particularly those exclusively animal-based, and those high-protein, low-fermentable carbohydrate/fibre 'weight-loss' diets, increasing the abundance of Bacteroides and lowering Firmicutes, with long-term adherence to such diets likely increasing risk of colonic disease. Interventions to prevent intestinal inflammation may be achieved with fermentable prebiotic fibres that enhance beneficial Bifidobacteria or with soluble fibres that block bacterial-epithelial adherence (contrabiotics). These mechanisms may explain many of the differences in microbiota associated with long-term ingestion of a diet rich in fruit and vegetable fibre. © 2015 The Authors. Alimentary Pharmacology & Therapeutics published by John Wiley & Sons Ltd.

  11. Effects of fibre content on mechanical properties and fracture behaviour of short carbon fibre reinforced geopolymer matrix composites

    Indian Academy of Sciences (India)

    Tiesong Lin; Dechang Jia; Meirong Wang; Peigang He; Defu Liang

    2009-02-01

    Geopolymer matrix composites reinforced with different volume fractions of short carbon fibres (Cf/geopolymer composites) were prepared and the mechanical properties, fracture behaviour and microstructure of as-prepared composites were studied and correlated with fibre content. The results show that short carbon fibres have a great strengthening and toughening effect at low volume percentages of fibres (3.5 and 4.5 vol.%). With the increase of fibre content, the strengthening and toughening effect of short carbon fibres reduce, possibly due to fibre damage, formation of high shear stresses at intersect between fibres and strong interface cohesion of fibre/matrix under higher forming pressure. The property improvements are primarily based on the network structure of short carbon fibre preform and the predominant strengthening and toughening mechanisms are attributed to the apparent fibre bridging and pulling-out effect.

  12. Knowledge about dietary fibre: a fibre study framework.

    Science.gov (United States)

    Guiné, Raquel P F; Ferreira, Manuela; Correia, Paula; Duarte, João; Leal, Marcela; Rumbak, Ivana; Barić, Irena C; Komes, Drazenka; Satalić, Zvonimir; Sarić, Marijana M; Tarcea, Monica; Fazakas, Zita; Jovanoska, Dijana; Vanevski, Dragoljub; Vittadini, Elena; Pellegrini, Nicoletta; Szűcs, Viktória; Harangozó, Júlia; El-Kenawy, Ayman; El-Shenawy, Omnia; Yalçın, Erkan; Kösemeci, Cem; Klava, Dace; Straumite, Evita

    2016-09-01

    The objective of this work was to study the degree of knowledge about dietary fibre (DF), as influenced by factors such as gender, level of education, living environment or country. For this, a descriptive cross-sectional study was undertaken on a non-probabilistic sample of 6010 participants from 10 countries in different continents (Europe, Africa and America). The results showed that the participants revealed on average a positive but still low global level of knowledge, which alerts for the need to take some actions to further inform the population about DF and its role as a component of a healthy diet. The results also indicated differences between genders, levels of education, living environments and countries. The highest level of knowledge was revealed by the participants from female gender, with higher education and living in urban areas. Concerning the country, the best informed were the participants from Romania, followed by those from Portugal and Turkey while the least informed were from Egypt.

  13. Comparison of Acoustic Characteristics of Date Palm Fibre and Oil Palm Fibre

    Directory of Open Access Journals (Sweden)

    Lamyaa Abd ALRahman

    2014-02-01

    Full Text Available This study investigated and compared the acoustic characteristics of two natural organic fibres: date palm fibre and oil palm fibre, these materials eligible for acoustical absorption. During the processing stage, both fibre sheets are treated with latex. The two fibres are compressed after latex treatment Circular samples (100 mm in diameter and 28 mm, based on the measurement tube requirements are cut out of the sheets. The density of the date palm fibre sheet is 150 kg/m3 for a 50 mm thickness and 130 kg/m3 for a 30 mm thickness. In contrast, the density of oil palm fibre is 75 kg/m3 for a 50 mm thickness and 65 kg/m3 for a 30 mm thickness. An impedance tube was used to test the thicknesses of both samples based on international standards. The results show that the date palm fibre exhibits two Acoustic Absorption Coefficient (AAC peaks: 0.93 at 1356 Hz and 0.99 at 4200-4353 Hz for the 50-mm-thick sample. In contrast, the 30-mm-thick sample has a single AAC peak of 0.83 at 2381.38-2809.38 Hz. However, the 50-mm-thick oil palm fibre has an AAC peak of 0.75 at 1946.88-2178.13 Hz and the 30-mm-thick oil palm fibre has an acoustic absorption coefficient peak 0.59 at 3225-3712.5 Hz. Thus, the date palm fibre has a higher acoustic absorption coefficient for high and low frequencies than does oil palm fibre. Both fibres are promising for use as sound absorber materials to protect against environmental noise pollution.

  14. “Direct modulation of a hybrid III-V/Si DFB laser with MRR filtering for 22.5-Gb/s error-free dispersion-uncompensated transmission over 2.5-km SSMF

    DEFF Research Database (Denmark)

    Cristofori, Valentina; Da Ros, Francesco; Ding, Yunhong;

    2016-01-01

    Error-free and penalty-free transmission over 2.5 km SSMF of a 22.5 Gb/s data signal from a directly modulated hybrid III-V/Si DFB laser is achieved by enhancing the dispersion tolerance using a silicon micro-ring resonator....

  15. “Direct modulation of a hybrid III-V/Si DFB laser with MRR filtering for 22.5-Gb/s error-free dispersion-uncompensated transmission over 2.5-km SSMF

    DEFF Research Database (Denmark)

    Cristofori, Valentina; Da Ros, Francesco; Ding, Yunhong

    2016-01-01

    Error-free and penalty-free transmission over 2.5 km SSMF of a 22.5 Gb/s data signal from a directly modulated hybrid III-V/Si DFB laser is achieved by enhancing the dispersion tolerance using a silicon micro-ring resonator....

  16. 食品中副溶血性弧菌toxR和tdh基因双色荧光PCR检测方法的建立%Detection of Vibrio parahaemolyticus toxR and tdh genes in foods by dual-color fluorescent real-time PCR

    Institute of Scientific and Technical Information of China (English)

    曹冬梅; 袁慕云; 许龙岩; 曹际娟

    2013-01-01

    Objective To establish a novel method to specifically detect Vibrio parahaemolyticus toxR and tdh genes in food by dual-color fluorescent real-time PCR. Methods The primers and probes targeting the toxR (transmembrane transcription activator) and tdh (thermostable direct hemolysin) were designed, and their specificity and sensitivity were tested with the Taqman probe dual-color fluorescent real-time PCR amplifica-tion system. The optimized method was used to detect the isolated bacterial strains and to explore the distribu-tion of toxR and tdh genes. Results Amplification curves of both toxR and tdh genes were obtained from standard V. parahaemolyticus strains and the three V. parahaemolyticus strains isolated from food-poisoning patients. However, no such amplification curve was observed for all the other newly isolated 31 bacterial strains, including Vibrio alginolyticus and L. monocytogenes from the genus Vibrio and the family Enterobacteriaceae. All the 37 food V. parahaemolyticus strains did not carry the tdh virulence gene. Furthermore, the detection sensitivity of this novel method reached 3.6×102 cfu/mL. Conclusion The novel dual-color fluorescent real-time PCR method was able to specifically and effectively detect V. parahaemolyticus in food samples.%目的建立对副溶血性弧菌(Vibrio parahaemolyticus)特异性检测 toxR(跨膜转录激活蛋白)基因和tdh(热稳定性直接溶血素)毒力基因的Taqman探针双色荧光PCR检测方法。方法根据副溶血性弧菌toxR基因和tdh基因,分别设计引物和探针,建立Taqman探针双色荧光PCR扩增体系,进行特异性、灵敏度试验;对副溶血性弧菌分离菌株实施检测,了解其tdh基因和tdh基因分布情况。结果结果表明,副溶血性弧菌标准菌株和3株从食物中毒患者中分离获得的分离株均出现toxR基因和tdh扩增曲线,而溶藻弧菌、单增李斯特菌等31株弧菌属其他菌株和肠杆菌科的菌株未见

  17. Ductility Performance of Hybrid Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    S. Eswari

    2008-01-01

    Full Text Available This study presents a study on the ductility performance of hybrid fibre reinforced concrete. The influence of fibre content on the ductility performance of hybrid fibre reinforced concrete specimens having different fibre volume fractions was investigated. The parameters of investigation included modulus of rupture, ultimate load, service load, ultimate and service load deflection, crack width, energy ductility and deflection ductility. A total of 27 specimens, 100×100×500 mm, were tested to study the above parameters. The specimens incorporated 0.0 to 2.0% volume fraction of polyolefin and steel fibres in different proportions. The ductility performance of hybrid fibre reinforced concrete specimens was compared with that of plain concrete. The test results show that addition of 2.0% by volume of hybrid fibres improves the ductility performance appreciably. An adaptive Neuro-Fuzzy based model has been proposed to predict the ductility performance characteristics. A reasonably close agreement has been obtained between the experimental and predicted results.

  18. Controllable spatiotemporal nonlinear effects in multimode fibres

    Science.gov (United States)

    Wright, Logan G.; Christodoulides, Demetrios N.; Wise, Frank W.

    2015-05-01

    Multimode fibres are of interest for next-generation telecommunications systems and the construction of high-energy fibre lasers. However, relatively little work has explored nonlinear pulse propagation in multimode fibres. Here, we consider highly nonlinear ultrashort pulse propagation in the anomalous-dispersion regime of a graded-index multimode fibre. Low modal dispersion and strong nonlinear coupling between the fibre's many spatial modes result in interesting behaviour. We observe spatiotemporal effects reminiscent of nonlinear optics in bulk media—self-focusing and multiple filamentation—at a fraction of the usual power. By adjusting the spatial initial conditions, we generate on-demand, megawatt, ultrashort pulses tunable between 1,550 and 2,200 nm dispersive waves over one octave; intense combs of visible light; and a multi-octave-spanning supercontinuum. Our results indicate that multimode fibres present unique opportunities for observing new spatiotemporal dynamics and phenomena. They also enable the realization of a new type of tunable, broadband fibre source that could be useful for many applications.

  19. Ceramic fibres for the automotive industry

    Energy Technology Data Exchange (ETDEWEB)

    Fryatt, J.

    1985-01-01

    The outstanding thermal, physical and chemical properties of ceramic fibres make them a noticeable contender for inclusion in engineered systems to satisfy such performance demands. A wide range of fibres and fibre-based products are available which exhibit such characteristics as high temperature continuous service ability (1600/sup 0/C if required), low thermal conductivity, excellent resistance to chemical attack (including reducing conditions), good acoustic performance at all temperatures and good resistance to vibration. They are also lightweight, fireproof and incombustible. Ceramic fibres should really be referred to as refractory fibres as they are based on combinations of high purity alumina and silica. Two groups of products exist. The most common have a continuous-use temperature of 1260/sup 0/C. These fibres are characterized by an alumina content of 40-50% but refractoriness and temperature use limit can be increased to about 1400/sup 0/C by modifying the basic chemistry. This generally involves increasing the alumina content to as much as 62% or adding chromia or zirconia to the basic mix. The second and less common group of fibres is characterized by both chemistry and crystal morphology. Chemistry is biased towards a high alumina content (over 70%), while production routes are designed to yield as high a crystal phase (and so enhanced high temperature stability) as possible.

  20. Comparison of two novel approaches to model fibre reinforced concrete

    NARCIS (Netherlands)

    Radtke, F.K.F.; Simone, A.; Sluys, L.J.

    2009-01-01

    We present two approaches to model fibre reinforced concrete. In both approaches, discrete fibre distributions and the behaviour of the fibre-matrix interface are explicitly considered. One approach employs the reaction forces from fibre to matrix while the other is based on the partition of unity f

  1. Coherent Beam Combination of Two Polarization Maintaining Ytterbium Fibre Amplifiers

    Institute of Scientific and Technical Information of China (English)

    HOU Jing; XIAO Rui; JIANG Zong-Fu; CHENG Xiang-Ai; SHU Bai-Hong; CHEN Jin-Bao; LIU Ze-Jin

    2005-01-01

    @@ We investigate coherent beam combination of fibre laser beams by phase locking. Phase noise of a polarization maintaining ytterbium fibre amplifier is inspected with a fibre interferometer. In a feed back control loop, two fibre polarization maintaining ytterbium amplifiers are phase locked and coherent combined when the phase noise is properly controlled by a LiNO3 phase modulator.

  2. Nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch

    . The combination of a small core size and zero-dispersion wavelength at the operating wavelength of widely available femtosecond Ti:sapphire lasers led to an extensive research in supercontinuum generation and other nonlinear effects in PCFs. It is crucial for the efficiency of many nonlinear mechanisms...... that the pump laser wavelength is close to the zero-dispersion wavelength and that the core size is small. Recently, work in fabricating PCFs from materials other than silica has intensified. One of the advantages of using alternative materials can be a higher inherent material nonlinearity, which...... to accurately obtain a small core size while maintaining small structural variations during fibre drawing. This talk will give a presentation of how the mPOFs are fabricated and the route to obtaining nonlinear effects in them....

  3. A Study in Physical and Mechanical Properties of Hemp Fibres

    Directory of Open Access Journals (Sweden)

    Asim Shahzad

    2013-01-01

    Full Text Available This paper presents the results of the experiments undertaken to evaluate various physical and mechanical properties of hemp fibres. The study of these properties is vital for comparison with similar properties of synthetic fibres and for assessing hemp fibres’ suitability for use as reinforcement in composite materials. The properties of hemp fibres were found to be good enough to be used as reinforcement in composite materials. However, the issues of relatively high moisture content of fibres, variability in fibre properties, and relatively poor fibre/matrix interfacial strength were identified as factors that can reduce the efficiency with which these fibres can be utilised.

  4. Radiation tolerance tests of scintillating fibres

    Energy Technology Data Exchange (ETDEWEB)

    Gavardi, Laura; Albrecht, Johannes [TU Dortmund (Germany); Collaboration: LHCb-Collaboration

    2016-07-01

    An upgrade of the LHCb detector is planned during the shutdown which will take place from mid 2018 to the end of 2019. The proposed upgrade for the tracking system is a detector composed of scintillating fibres read out by silicon photomultipliers. The tracking detector will be working in an environment exposed to radiation, so that the resistance of the fibres to radiation is an important quality, which needs to be investigated. In this talk tests of scintillating fibres tolerance to radiation will be presented.

  5. Analysing the nanoporous structure of aramid fibres

    DEFF Research Database (Denmark)

    Pauw, Brian Richard; Vigild, Martin Etchells; Mortensen, Kell;

    2010-01-01

    After consideration of the applicability of classical methods, a novel analysis method for the characterization of fibre void structures is presented, capable of fitting the entire anisotropic two-dimensional scattering pattern to a model of perfectly aligned, polydisperse ellipsoids. It is tested...... for validity against the computed scattering pattern for a simulated nanostructure, after which it is used to fit the scattering from the void structure of commercially available heat-treated poly(p-phenylene terephtalamide) fibre and its as-spun precursor fibre. The application shows a reasonable fit...

  6. Silica holey fibres: fabrication and nonlinear effects

    OpenAIRE

    Belardi, W.; Monro, T.M.; Lee, J.H.; Yusoff, Z.; Price, J.H.V.; Malinowski, A.; Piper, A; Richardson, D J

    2002-01-01

    Holey fibres (HFs) [1] have emerged as a novel class of optical fibres which can provide completely new optical properties, such as endlessly single mode operation and novel dispersion properties as anomalous dispersion below 1.3µm, broadband flat dispersion and highly normal dispersion at 1.55µm. Moreover by changing the HF parameters (i.e. hole and core size), it is possible to fabricate HFs with an effective area so high as 800µm2 or so low as approximately 1µm2 [2]. A holey fibre perform ...

  7. Fibre Optic Protection System for Concrete Structures

    Institute of Scientific and Technical Information of China (English)

    J.S.Leng; A.Hameed; D.Winter; R.A.Barnes; G.C.Mays; G.F.Fernando

    2006-01-01

    The design concepts, modelling and implementation of various fibre optic sensor protection systems for development in concrete structures were investigated. Design concepts and on-site requirements for surface-mounted and embedded optical fibre sensor in concrete were addressed. Finite element (FE) modelling of selected sensor protection systems in strain-transfer efficiency from the structure to the sensing region was also studied. And experimental validation of specified sensor protection system was reported. Results obtained indicate that the protection system for the sensors performs adequately in concrete environment and there is very good correlation between results obtained by the protected fibre optic sensors and conventional electrical resistance strain gauges.

  8. Fibre optic power meter calibration uncertainties

    CSIR Research Space (South Africa)

    Nel, M

    2010-06-01

    Full Text Available thereof. It was done only for standard single mode fibre with FC (ferrule connector) connectors, and using a 1310 and a 1550 nm Fabry Perot laser (FP laser). The calibration set-up and procedure The uncertainty contributions for fibre optic power..., in this case 1310 or 1550 nm, is fed to the fibre optic power meter (secondary standard or unit under test (UUT)) via an attenuator. The attenuator serves to reduce back-reflections into the source and to set the power to the desired level. In Fig. 1...

  9. The coupling performance of photonic crystal fibres in fibre stellar interferometry

    DEFF Research Database (Denmark)

    Corbett, J.; Dabirian, A.; Butterley, T.;

    2006-01-01

    Large mode area (LMA), single-mode photonic crystal fibres (PCFs) have the potential to provide significant instrumental advantages in fibre stellar interferometry, due to their broadband attenuation spectrum, endlessly single-moded performance and very large core size. We investigate the theoret......Large mode area (LMA), single-mode photonic crystal fibres (PCFs) have the potential to provide significant instrumental advantages in fibre stellar interferometry, due to their broadband attenuation spectrum, endlessly single-moded performance and very large core size. We investigate...... the theoretical performance of coupling the telescope point spread function directly into LMA PCFs. We find that a single LMA fibre can replace as many as three step-index fibres for atmospheric seeing characterized by D-T/r(o) >= 2 with approximately the same coupling performance and a slower feed from...

  10. Rare-Earth Doped Photonic Crystal Fibre Lasers and Amplifiers

    DEFF Research Database (Denmark)

    Hougaard, Kristian G.

    2005-01-01

    In this thesis, a theoretical and numerical study of the use of rare-earthdoped photonic crystal fibres as optical amplifiers and lasers, has been performed. Photonic crystal fibres or microstructured optical fibres is a new kind of optical fibre in which the cladding region typically consist...... of a periodic microstructure, resulting in a fibre with very different properties compared to conventional optical fibres. The properties of photonic crystals fibres are described, with focus on the advantages this technology provides compared to conventional fibres, within the area of optical amplification....... The thesis also presents the basic properties of optical amplification, and describes the numerical model developed to model the behaviour of lasers and amplifiers based on photonic crystal fibres. The developed numerical tools are then used to investigate specific applications of photonic crystal fibres...

  11. Methodology for characterisation of glass fibre composite architecture

    DEFF Research Database (Denmark)

    Hansen, Jens Zangenberg; Larsen, J.B.; Østergaard, R.C.

    2012-01-01

    of the fibres. The information is used for different analyses to investigate and characterise the fibre architecture. As an example, the methodology is applied to glass fibre reinforced composites with varying fibre contents. The different fibre volume fractions (FVFs) affect the number of contact points per......The present study outlines a methodology for microstructural characterisation of fibre reinforced composites containing circular fibres. Digital micrographs of polished cross-sections are used as input to a numerical image processing tool that determines spatial mapping and radii detection...... fibre, the communal fibre distance and the local FVF. The fibre diameter distribution and packing pattern remain somewhat similar for the considered materials. The methodology is a step towards a better understanding of the composite microstructure and can be used to evaluate the interconnection between...

  12. A temperature-independent fibre-optic magnetic-field sensor using thin-core fibre tailored fibre Bragg grating

    Science.gov (United States)

    Tian, Qin; Feng, Zhongyao; Rong, Qiangzhou; Wan, Yun; Qiao, Xueguang; Hu, Manli; Yang, Hangzhou; Wang, Ruohui; Shao, Zhihua; Yang, Tingting

    2017-06-01

    A temperature-independent fibre-optic magnetic-field sensor is proposed and demonstrated experimentally. The device consists of a thin-core fibre (TCF) sandwiched in the upstream of a fibre Bragg grating (FBG). Because of the core-mismatch between the TCF and the single-mode fibre (SMF), the core mode is coupled to the cladding modes within the TCF cladding, and parts of them are recoupled back to the leading-in SMF by the downstream FBG. The cladding modes are sensitive to the ambient refractive index (RI), and therefore have the ability to respond to a RI change in the magnetic fluid determined by the ambient magnetic field. The intensities of the cladding-mode resonances are highly sensitive to the magnetic field change, while, in contrast, the resonance wavelengths always remain unchanged. This property can allow the sensor to act as a power-referenced reflection probe for magnetic field measurements.

  13. Polymerizing the fibre between bacteria and host cells: the biogenesis of functional amyloid fibres

    OpenAIRE

    2008-01-01

    Amyloid fibres are proteinaceous aggregates associated with several human diseases, including Alzheimer’s, Huntington’s and Creutzfeldt Jakob’s. Disease-associated amyloid formation is the result of proteins that misfold and aggregate into β sheet-rich fibre polymers. Cellular toxicity is readily associated with amyloidogenesis, although the molecular mechanism of toxicity remains unknown. Recently, a new class of ‘functional’ amyloid fibres was discovered that demonstrates that amyloids can ...

  14. Strength Evaluation of Steel-Nylon Hybrid Fibre Reinforced Concrete

    OpenAIRE

    Maniram Kumar; Er. Ankush Khadwal

    2014-01-01

    When fibres like steel, glass, polypropylene, nylon, carbon, aramid, polyester, jute, etc are mixed with concrete known as fibre reinforced concrete. To overcome the deficiencies of concrete; fibres are added to improve the performance of concrete. In this research hybrid reinforced concrete is made by using steel and nylon 6 fibres. The inclusion of both steel and nylon 6 fibres are used in order to combine the benefits of both fibers; structural improvements provided by stee...

  15. Synchronously pumped picosecond all-fibre Raman laser based on phosphorus-doped silica fibre.

    Science.gov (United States)

    Kobtsev, Sergey; Kukarin, Sergey; Kokhanovskiy, Alexey

    2015-07-13

    Reported for the first time is picosecond-range pulse generation in an all-fibre Raman laser based on P₂O₅-doped silica fibre. Employment of phosphor-silicate fibre made possible single-cascade spectral transformation of pumping pulses at 1084 nm into 270-ps long Raman laser pulses at 1270 nm. The highest observed fraction of the Stokes component radiation at 1270 nm in the total output of the Raman laser amounted to 30%. The identified optimal duration of the input pulses at which the amount of Stokes component radiation in a ~16-m long phosphorus-based Raman fibre converter reaches its maximum was 140-180 ps.

  16. Polarisation effects in twin-core fibre: Application for mode locking in a fibre laser

    Science.gov (United States)

    Lobach, I. A.; Kablukov, S. I.; Podivilov, Evgenii V.; Babin, Sergei A.; Apolonski, A. A.

    2012-09-01

    We report the first measurements of the longitudinal power distribution in a twin-core optical fibre at different input light polarisations. Experimental evidence is presented that, because of the difference in birefringence between the cores, the power in them depends on which core the beam is launched into. Experimental data are interpreted in terms of a modified polarisation model for mode coupling in twin-core fibres which takes into account the birefringence of the cores. In addition, we demonstrate for the first time the use of the polarisation properties of a twincore fibre for mode locking in a fibre laser.

  17. Yb3+-Doped Double-Clad Fibre Laser Based on Fibre Bragg Grating

    Institute of Scientific and Technical Information of China (English)

    范万德; 付圣贵; 张强; 宁鼎; 李丽君; 王志; 袁树忠; 董孝义

    2003-01-01

    A novel Yb3+-doped double-clad fibre laser based on a double-clad fibre Bragg grating is presented. The fibre Bragg grating, as the output mirror, has been formed in Yb3+-doped double-clad fibre with the phase-mask method. When the input pump power is 2.8 W, the maximum laser output power is 570mW, with < 0.2 nm in line-width at the wavelength of 1.058μm, over 40dB signal-to-noise ratio and 24% slope efficiency.

  18. ELASTICITY of SHORT FIBRE REINFORCED POLYAMIDE: MORPHOLOGICAL AND NUMERICAl ANALYSIS OF FIBRE ORIENTATION EFFECTS

    Directory of Open Access Journals (Sweden)

    Francesca Cosmi

    2010-10-01

    Full Text Available The fatigue behaviour of injection moulded short fibre reinforced polymers depends upon fibre orientation, as shown in experiments conducted with notched specimens injected through different injection gates. The different fatigue behaviour is mainly related to the different local elastic properties, as determined by the different fibre orientation patterns, resulting into different strain distributions. In order to quantify the relationship between fibre orientation and elastic constants, the Cell Method was applied to volumes extracted from the specimens, reconstructed by micro-tomography.

  19. Individual fibre segmentation from 3D X-ray computed tomography for characterising the fibre orientation in unidirectional composite materials

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Jespersen, Kristine Munk; Dahl, Anders Bjorholm

    2017-01-01

    The aim of this paper is to characterise the fibre orientation in unidirectional fibre reinforced polymers, namely glass and carbon fibre composites. The compression strength of the composite is related to the orientation of the fibres. Thus the orientation is essential when designing materials...... for wind turbine blades. The calculation of the fibre orientation distribution is based on segmenting the individual fibres from volumes that have been acquired through X-ray tomography. The segmentation method presented in this study can accurately extract individual fibres from low contrast X-ray scans...... of composites with high fibre volume fraction. From the individual fibre orientations, it is possible to obtain results which are independent of the scanning quality. The compression strength for both composites is estimated from the average fibre orientations and is found to be of the same order of magnitude...

  20. 纳米压印工艺制作DFB激光器的可靠性研究%Reliability Study of DFB Laser Fabricated by Nanoimprint Technology

    Institute of Scientific and Technical Information of China (English)

    赵建宜; 陈鑫; 周宁; 曹明德; 黄晓东; 刘文

    2014-01-01

    利用光荧光谱及X射线双晶衍射研究了纳米压印工艺对半导体外延材料的影响.利用纳米压印工艺制作了1.55 μm通信用分布反馈(DFB)半导体激光器,并对制作的器件进行了老化寿命试验.实验结果表明,采用软模版压印并不会劣化半导体外延材料的特性.制作的半导体激光器预期寿命与普通双光束曝光法制得的器件预期相当,表明纳米压印工艺制作半导体激光器是可靠的.

  1. Design Methods for Fibre Reinforced Concrete

    DEFF Research Database (Denmark)

    Stang, Henrik

    1996-01-01

    The present paper describes the outline of a research project on Fibre Reinforced Concrete (FRC) currently being carried out in Denmark under the supervision of Danish Council of Technology, Danish Technical Research Council and Danish Natural Science Research Counsil....

  2. Optical fibres bringing the LHC into focus

    CERN Multimedia

    2003-01-01

    New components are being added to CERN's optical fibre network, which will transport the torrents of data produced by the LHC. 1500 kilometres of cables will be installed in the tunnels and at ground level.

  3. Chinese Market for Fibres and Cables

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    This article presents a summary of Chinese market of optical fibres and cables based on the development of the optical communications industry. Analysis shows that the market will keep growing for sometime in the future.

  4. Flatus emission patterns and fibre intake.

    Science.gov (United States)

    Bolin, T D; Stanton, R A

    1998-01-01

    Knowledge of the normal range of flatus emissions and their relationship to diet, particularly fibre, would be helpful in managing patients who complain of excessive flatus or abdominal distention. Sixty men and 60 women aged between 17 and 67 kept a three-day daily record, including one week-end day, of their flatus emissions, dietary fibre intake and beer consumption. Daily flatus emissions averaged 12.7 (range to 2-53) for men and 7.1 (range 1-32) for women. Fibre intake averaged 28+/-13 g for men and 24+/-3 g for women. Flatus emissions significantly correlated with dietary fibre intake (pflatus emissions and beer intake in men and men recorded more aromatic flatus than women. This study of 120 normal individuals eating their choice of foods provides a basis to judge degrees of abnormality in patients complaining of excessive flatus.

  5. Optical Fibre Pressure Sensors in Medical Applications

    Directory of Open Access Journals (Sweden)

    Sven Poeggel

    2015-07-01

    Full Text Available This article is focused on reviewing the current state-of-the-art of optical fibre pressure sensors for medical applications. Optical fibres have inherent advantages due to their small size, immunity to electromagnetic interferences and their suitability for remote monitoring and multiplexing. The small dimensions of optical fibre-based pressure sensors, together with being lightweight and flexible, mean that they are minimally invasive for many medical applications and, thus, particularly suited to in vivo measurement. This means that the sensor can be placed directly inside a patient, e.g., for urodynamic and cardiovascular assessment. This paper presents an overview of the recent developments in optical fibre-based pressure measurements with particular reference to these application areas.

  6. Central Tracking Detector Based on Scintillating Fibres

    CERN Multimedia

    2002-01-01

    Scintillating fibres form a reasonable compromise for central tracking detectors in terms of price, resolution, response time, occupancy and heat production. \\\\ \\\\ New fluorescents with large Stokes shifts have been produced, capable of working without wavelength shifters. Coherent multibundles have been developed to achieve high packing fractions. Small segments of tracker shell have been assembled and beam tests have confirmed expectations on spatial resolution. An opto-electronic delay line has been designed to delay the track patterns and enable coincidences with a first level trigger. Replacement of the conventional phosphor screen anode with a Si pixel chip is achieved. This tube is called ISPA-tube and has already been operated in beam tests with a scintillating fibres tracker. \\\\ \\\\ The aim of the proposal is to improve hit densities for small diameter fibres by increasing the fraction of trapped light, by reducing absorption and reflection losses, by reflecting light at the free fibre end, and by inc...

  7. Step index fibre using laser interferometer

    Indian Academy of Sciences (India)

    A M Hamed

    2014-03-01

    model is suggested to describe the fringe shift which occurs due to the phase variations of cladded glass fibre introduced between the two plates of the liquid wedge interferometer illuminated with a He–Ne laser. The fringe shift of the phase object which appears in the denominator of the Airy distribution formula of the multiple beam interference is represented in the harmonic term. An experiment is conducted using liquid wedge interferometer where the step index glass fibre of a nearly quadratic thickness variation is introduced between the two plates of the interferometer. The obtained fringe shift shows a good agreement with the proposed quadratic model. The Matlab code is written to plot the interferometer fringes comprising the shift of the step index fibre. Secondly, recognition of elliptical fibres is outlined using tomographic imaging. Finally, results and concluding remarks are given.

  8. Design of distributed feedback fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Søndergaard, Thomas; Varming, Poul

    1997-01-01

    A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift.......A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift....

  9. Energy transfer during the hydroentanglement of fibres

    CSIR Research Space (South Africa)

    Moyo, D

    2012-10-01

    Full Text Available , and the resultant degree of fibre entanglement, determines the tensile strength of the nonwoven fabric as a consequence of the inter-fibre friction. Here, the relationship between hydroentangling energy from the waterjets and the changes it brings about... in the nonwoven fabric strength were studied. In the study, the energies of the waterjets transferred to every fabric sample as a function of the waterjet pressure, machine speed, machine efficiency and the web area weight were quantified, and the resultant...

  10. Fibre-optic sensors in health care

    Science.gov (United States)

    Grazia Mignani, Anna; Baldini, Francesco

    1997-05-01

    Biomedical fibre-optic sensors are attractive for the measurement of physical, chemical and biochemical parameters and for spectral measurements directly performed on the patient. An overview of fibre-optic sensors for in vivo monitoring is given, with particular attention paid to the advantages that these sensors are able to offer in different application fields such as cardiovascular and intensive care, angiology, gastroenterology, ophthalmology, oncology, neurology, dermatology and dentistry.

  11. Angiogenic effect induced by mineral fibres.

    Science.gov (United States)

    Carbonari, Damiano; Campopiano, Antonella; Ramires, Deborah; Strafella, Elisabetta; Staffolani, Sara; Tomasetti, Marco; Curini, Roberta; Valentino, Matteo; Santarelli, Lory; Amati, Monica

    2011-10-09

    Due to the toxic effect of asbestos, other materials with similar chemical-physical characteristics have been introduced to substitute it. We evaluate the angiogenic effect of certain asbestos substitute fibres such as glass fibres (GFs), ceramic fibres (CFs) and wollastonite fibres (WFs) and then compare angiogenic responses to those induced by crocidolite asbestos fibres (AFs). An in vitro model using human endothelial cells in small islands within a culture matrix of fibroblasts (Angio-Kit) was used to evaluate vessel formation. The release of IL-6, sIL-R6, IL-8, VEGF-A and their soluble receptors, sVEGFR-1, sVEGFR-2, was determined in the conditioning medium of Angio-Kit system after fibre treatment. ROS formation and cell viability were evaluated in cultured endothelial cells (HUVEC). To evaluate the involvement of intracellular mechanisms, EGFR signalling, ROS formation and nuclear factor-κB (NFκB) pathway were then inhibited by incubating HUVEC cells with AG1478, NAC and PDTC respectively, and the cytokine and growth factor release was analyzed in the culture medium after 7 days of fibre incubation. Among the mineral fibres tested, WFs markedly induced blood vessel formation which was associated with release of IL-6 and IL-8, VEGF-A and their soluble receptors. ROS production was observed in HUVEC after WFs treatment which was associated with cell cytotoxicity. The EGFR-induced ERK phosphorylation and ROS-mediated NFκB activation were involved in the cytokine and angiogenic factor release. However, only the EGFR activation was able to induce angiogenesis. The WFs are potential angiogenic agents that can induce regenerative cytokine and angiogenic factor production resulting in the formation of new blood vessels.

  12. Photonic crystal fibres in the market

    DEFF Research Database (Denmark)

    Broeng, Jes; Laurila, Marko; Noordegraaf, Danny;

    2011-01-01

    Photonic crystal fibres (PCFs) emerged as a research topic in the mid 1990'ies [1]. Today, 15 years later, these fibres are increasing deployed in various commercial markets. Here, we will address three of these markets; medical imaging, materials processing and sensors. We will describe how...... the PCFs provide radical improvements and illustrate the strong diversity in the evolution of PCFs to serve these different markets....

  13. Force focusing in confined fibres and sheets

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Victor; Cerda, Enrique [Departamento de Fisica, Universidad de Santiago, Av. Ecuador 3493, Santiago (Chile); Witten, T A; Liang Tao [James Franck Institute, University of Chicago, Chicago IL 60637 (United States)], E-mail: t-witten@uchicago.edu

    2008-07-07

    A thin fibre or sheet curled into a circular container has a detached region whose shape and force ratios are independent of material properties and container radius. We compute this shape and compare it with experiments. The discrete forces acting at either end of the detached region have a ratio that depends only on the length of the fibre or sheet relative to the circle radius. We calculate this force ratio in three regimes of circle radius. (fast track communication)

  14. Economics Of Optical Fibre Transmission Systems

    Science.gov (United States)

    Murray, W. J.

    1983-08-01

    Optical fibre as a telecommunication transmission medium has become one of the most significant developments so far of the digital era. A major contributory factor to the availability of optical fibre transmission systems has been the outstanding progress in the technology of manufacturing high quality glass fibre having relatively low attenuation and broad bandwidths. This and other achievements has enabled manufacturers in the United Kingdom to develop a range of optical fibre cables and transmission equipment for operation over short and long distances at the CCITT recommended digital hierarchical rates of 2, 8, 34 and 140Mbit/s which have been adopted by British Telecom (BT) for modernisation to an all digital transmission network. These optical fibre systems are now becoming increasingly price and performance competitive with conventional technology in many parts of telecommunications networks. In the British Telecom (BT) network the 140Mbit/s optical fibre systems are now economically competitive with equivalent systems on coaxial cable and microwave radio. The economics of 8 and 34Mbit/s systems are not yet sufficiently attractive, compared with 2Mbit/s digital line systems on pair type copper cables, for large scale use in rural and local distribution networks and are presently only justified on cost in and around large cities. As system costs decrease large applications are predicted particularly in support of future high speed data, cable television and visual information services.

  15. Fibre positioning algorithms for the WEAVE spectrograph

    Science.gov (United States)

    Terrett, David L.; Lewis, Ian J.; Dalton, Gavin; Abrams, Don Carlos; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Middleton, Kevin; Trager, Scott C.

    2014-07-01

    WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. It is a multi-object "pick and place" fibre fed spectrograph with more than one thousand fibres, similar in concept to the Australian Astronomical Observatory's 2dF1 instrument with two observing plates, one of which is observing the sky while other is being reconfigured by a robotic fibre positioner. It will be capable of acquiring more than 10000 star or galaxy spectra a night. The WEAVE positioner concept uses two robots working in tandem in order to reconfigure a fully populated field within the expected 1 hour dwell-time for the instrument (a good match between the required exposure times and the limit of validity for a given configuration due to the effects of differential refraction). This presents additional constraints and complications for the software that determines the optimal path from one configuration to the next, particularly given the large number of fibre crossings implied by the 1000 fibre multiplex. This paper describes the algorithms and programming techniques used in the prototype implementations of the field configuration tool and the fibre positioner robot controller developed to support the detailed design of WEAVE.

  16. Criticality and isostaticity in fibre networks

    Science.gov (United States)

    Broedersz, Chase P.; Mao, Xiaoming; Lubensky, Tom C.; Mackintosh, Frederick C.

    2011-12-01

    Disordered fibre networks are the basis of many man-made and natural materials, including structural components of living cells and tissue. The mechanical stability of such networks relies on the bending resistance of the fibres, in contrast to rubbers, which are governed by entropic stretching of polymer segments. Although it is known that fibre networks exhibit collective bending deformations, a fundamental understanding of such deformations and their effects on network mechanics has remained elusive. Here we introduce a lattice-based model of fibrous networks with variable connectivity to elucidate the roles of single-fibre elasticity and network structure. These networks exhibit both a low-connectivity rigidity threshold governed by fibre-bending elasticity and a high-connectivity threshold governed by fibre-stretching elasticity. Whereas the former determines the true onset of network rigidity, we show that the latter exhibits rich zero-temperature critical behaviour, including a crossover between various mechanical regimes along with diverging strain fluctuations and a concomitant diverging correlation length.

  17. Jute fibre reinforced plastic: evaluation of application based properties

    Directory of Open Access Journals (Sweden)

    J. B. Sajin

    2015-01-01

    Full Text Available A fibre extracted from jute is a budding component identified for its potential application in composites. It is imperative to evaluate the parametric and property based features to determine its suitability. In this research study, considering the possible application of the fibre composites, the aptness of these fibres are examined with respect to their physical, mechanical [by layered manufacturing technique(LM] and thermal properties. This study focuses on evaluating the properties and behaviour of raw Jute fibres and NaOH surface treated fibres. Subsequently, the fibres are subjected to thermo-gravimetry tests. The outcome of the thermal analysis clearly indicates that the temperature peak shifts to a higher region in the treated fibre compared to raw fibre. The overall observation strongly emphasize that the physical properties and the thermal behaviour of jute fibre are enhanced after surface treatments which makes it more feasible for its application in composite structures.

  18. Loss of type I fibres in canine pectineus muscle hypotrophy.

    Science.gov (United States)

    Ihemelandu, E C

    1980-01-01

    The total number of fibres, as well as, the number of fibres per fibre type were determined by the indirect fibre-counting method in 32 pectineus muscles from 16 dogs of mixed sexes. Eight pairs of muscles from 8 dogs were judged to be hypotrophic, while the other 8 pairs from another 8 dogs were judged to be normal. The hypotrophic muscles had extremely small muscle fibres, particularly type II fibres. They also had apparently higher percentages of type II muscle fibres within a section. The apparently higher percentage of type II fibres usually observed in the hitsochemical examination of the sections of hypotrophic pectineus muscles did not result from failure of type II fibres to transform to type I fibres. It was rather due to too few type I fibres being present in these muscles as compared to the normal muscles. It was not because there were more type II fibres present in them than in the normal muscles. The fewer type I fibres resulted most likely from loss of already differentiated type I fibres. The loss may be of neural origin.

  19. The effect of fibre content, fibre size and alkali treatment to Charpy impact resistance of Oil Palm fibre reinforced composite material

    Science.gov (United States)

    Fitri, Muhamad; Mahzan, Shahruddin

    2016-11-01

    In this research, the effect of fibre content, fibre size and alkali treatment to the impact resistance of the composite material have been investigated, The composite material employs oil palm fibre as the reinforcement material whereas the matrix used for the composite materials are polypropylene. The Oil Palm fibres are prepared for two conditions: alkali treated fibres and untreated fibres. The fibre sizes are varied in three sizes: 5mm, 7mm and 10mm. During the composite material preparation, the fibre contents also have been varied into 3 different percentages: 5%, 7% and 10%. The statistical approach is used to optimise the variation of specimen determined by using Taguchi method. The results were analyzed also by the Taguchi method and shows that the Oil Palm fibre content is significantly affect the impact resistance of the polymer matrix composite. However, the fibre size is moderately affecting the impact resistance, whereas the fibre treatment is insignificant to the impact resistance of the oil palm fibre reinforced polymer matrix composite.

  20. Crack Growth Monitoring by Embedded Optical Fibre Bragg Grating Sensors: Fibre Reinforced Plastic Crack Growing Detection

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira; Mikkelsen, Lars Pilgaard; McGugan, Malcolm

    2015-01-01

    This article presents a novel method to asses a crack growing/damage event in fibre reinforced plastic, or adhesive using Fibre Bragg Grating (FBG) sensors embedded in a host material. Different features of the crack mechanism that induce a change in the FBG response were identified. Double Canti...

  1. Magnesium Coated Bioresorbable Phosphate Glass Fibres: Investigation of the Interface between Fibre and Polyester Matrices

    Directory of Open Access Journals (Sweden)

    Xiaoling Liu

    2013-01-01

    Full Text Available Bioresorbable phosphate glass fibre reinforced polyester composites have been investigated as replacement for some traditional metallic orthopaedic implants, such as bone fracture fixation plates. However, composites tested revealed loss of the interfacial integrity after immersion within aqueous media which resulted in rapid loss of mechanical properties. Physical modification of fibres to change fibre surface morphology has been shown to be an effective method to improve fibre and matrix adhesion in composites. In this study, biodegradable magnesium which would gradually degrade to Mg2+ in the human body was deposited via magnetron sputtering onto bioresorbable phosphate glass fibres to obtain roughened fibre surfaces. Fibre surface morphology after coating was observed using scanning electron microscope (SEM. The roughness profile and crystalline texture of the coatings were determined via atomic force microscope (AFM and X-ray diffraction (XRD analysis, respectively. The roughness of the coatings was seen to increase from 40±1 nm to 80±1 nm. The mechanical properties (tensile strength and modulus of fibre with coatings decreased with increased magnesium coating thickness.

  2. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin;

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature ph...

  3. Estimation of Single-fibre Tensile Properties from the Bundle Tensile Curve of Polyester Fibres

    Institute of Scientific and Technical Information of China (English)

    于伟东

    2004-01-01

    Fibre bundle tensile curves can be used to characterise fibre processing properties and end-use performance directly and to predict single-fibre properties in theory. In this paper, the tensile behaviour of polyester fibre-bundles has been analysed in characteristic values and diagramming. The characteristic distributions which include the symmetry distribution on right part, SRBS′ (e), on left part, SLBS′(e) and the curve on base-line modification, MBS′ (e),based on the modulus distribution, BS′ (e), as well as the frequency density function of broken fibres, B′ (e), have been derived from the tail of bundle tensile curves. The theoretical and measured results show that the most important curves are MBS′ ( e ) and B′ ( e ) and can be used to estimate the breaking-extension distribution of single fibres. Especially for MBS′(e), the modulus distribution can accurately characterize single-fibre tensile properties and is no limitation as the calculation of B′(e) because the bundle specific stress Y(e) of no fibre breaking at extension e should be found at first.

  4. Strength Evaluation of Steel-Nylon Hybrid Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    Maniram Kumar

    2014-07-01

    Full Text Available When fibres like steel, glass, polypropylene, nylon, carbon, aramid, polyester, jute, etc are mixed with concrete known as fibre reinforced concrete. To overcome the deficiencies of concrete; fibres are added to improve the performance of concrete. In this research hybrid reinforced concrete is made by using steel and nylon 6 fibres. The inclusion of both steel and nylon 6 fibres are used in order to combine the benefits of both fibers; structural improvements provided by steel fibers and the resistance to plastic shrinkage improvements provided by nylon fibers. So the aim of this project is to investigate the mechanical properties (compressive strength, flexure strength and split tensile strength of hybrid fiber reinforced concrete under compression, flexure & tension. The total volume of fibre was taken 0.75 % of total volume of concrete. In this experimental work, four different concrete mix proportions were casted with fibres and one mix without fibres. Four different mix combinations of steel- nylon 6 fibres were 100-00%, 75-25%, 50-50% and 25-75%. Superplasticizer was used in all mixes to make concrete more workable. The results shown that compressive, split tensile and flexural strength of hybrid fibre reinforced concrete increase by increasing quantity of steel and nylon 6 fibres. The increase in compressive and tensile strength due to incorporation of steel fibre is greater than that of using nylon fibre. For the nylon 6 fibres, adding more fibres into the concrete has a limited improvement on splitting tensile strength. Inclusion of nylon 6 fibres along with steel fibres results in considerable improvement in flexural strength as compared to solo steel fibre.

  5. D fibre antenna for microcellular communications

    Energy Technology Data Exchange (ETDEWEB)

    Bhatti, Ajaz

    2003-07-01

    Over the years, optical fibre sensors have been developed for many application areas. With the recent growth of microcellular communication systems this area has great economic potential. Therefore with this in mind one promising application for a new optical fibre sensor system is in the detection of Radio Frequency/Electric Fields (RF/EF). By constructing such a sensor from totally dielectric materials, it could be used as an antenna for receiving radio frequency transmissions without distorting or disturbing the field lines since there are no metallic components to reflect or transmit radio frequency energy. One of the key issues in the realisation of Radio-over-Fibre (RoF) architecture is the development of an effective means of generating and transmitting the radio subcarrier. The simplest method for the optical generation of radio signals, for transmission through an optical network is to directly modulate the light source with the received RF signal. Direct modulation of the laser can lead to a number of problems such as relative intensity noise (RIN), chirp and intermodulation distortion (IMD). A novel approach as described in this thesis, for generating an externally modulated optical signal would be to use an optical antenna comprising of a piezoelectric polymer coated D-fibre configured within a Mach-Zehnder interferometer to phase modulate the lightwave with a received RF electrical signal. One of the primary advantages of the D-fibre antenna over conventional antennae is its ability to serve a dual purpose. First it can be used to directly detect the RF signal, and secondly it provides a convenient means for modulating the light within the fibre thus bypassing the need for directly modulating the laser. The work presented in this thesis forms a comprehensive study on the design and modelling of a novel all-optical antenna using D-shaped optical fibre for use in next generation RoF networks. For the first time Finite Element Analysis (FEA) has been used

  6. Fibre Bragg Grating and Long Period Grating Sensors in Polymer Optical Fibres

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar

    of applications and pushing the limits. The first part of the work focuses on the fabrication of FBGs in polymer optical fibres. FBGs are a periodic perturbation of the refractive index of the optical fibre core which act as a wavelength specific reflector. The fibres used are made of Polymethyl methacrylate......, strain duration, increasing number of cycles, and it decreases with relaxation duration. For strains up to 0.9%, fast relaxing ΔΛfast range takes no less than 65% of the total strain range. Increase in ΔΛslow due to cyclic straining and relaxing seems to reach an equilibrium value, suggesting that ΔΛslow...... which translates the outside pressure into strain on the fibre. The transducer consisted of a 3Dprinted skeleton through which the fibre is pulled. A latex material is then wrapped around it and all the holes were sealed in order to prevent the air from leaking out. The pod transducer was tested...

  7. Study of the behaviour of the fibre Bragg grating fabricated with cladding mode suppression fibre

    Institute of Scientific and Technical Information of China (English)

    徐新华; 吕昌贵; 崔一平

    2003-01-01

    One effective method for suppression of coupling from guided optical modes into cladding modes in an optical fibre Bragg grating is to use cladding mode suppression fibre.In this specially engineered fibre,the grating is written into the core and the inner cladding,both of which are photosensitive.A theory is presented in this paper to analyse the spectral characteristics of this kind of gratings.A fibre Bragg grating was experimentally fabricated with this kind of photosensitive fibre(PS-RMS-50 from StockerYale).It is shown both theoretically and experimentally that such gratings exhibit strong suppression of the coupling between core mode and cladding mode.The experimental result is in good agreement with the theoretical analysis.

  8. Hemp fibres: Enzymatic effect of microbial processing on fibre bundle structure

    DEFF Research Database (Denmark)

    Thygesen, Anders; Liu, Ming; Meyer, Anne S.

    2013-01-01

    The effects of microbial pretreatment on hemp fibres were evaluated after microbial retting using the white rot fungi Ceriporiopsis subvermispora and Phlebia radiata Cel 26 and water retting. Based on chemical composition, P. radiata Cel 26 showed the highest selectivity for pectin and lignin...... degradation and lowest cellulose loss (14%) resulting in the highest cellulose content (78.4%) for the treated hemp fibres. The pectin and lignin removal after treatment with P. radiata Cel 26 were of the order 82% and 50%, respectively. Aligned epoxy-matrix composites were made from hemp fibres defibrated...... hemp fibres were badly impregnated due to porosity caused by surface impurities such as epidermis and other pectin rich plant cells. The pectin and lignin mainly located in the outer part of the fibres were assumed to be extracted and degraded by pectinase and peroxidase enzymes produced by the fungi....

  9. Polarisation maintaining fibre with pure silica core and two depressed claddings for fibre optic gyroscope

    Science.gov (United States)

    Kurbatov, A. M.; Kurbatov, R. A.; Voloshin, V. V.; Vorob'ev, I. L.; Kolosovsky, A. O.

    2016-12-01

    Polarisation maintaining (PM) fibre is described with pure silica core and two depressed claddings for fibre optic gyro (FOG) sensing coil. Detailed mathematical simulation is presented by supermodes method, which is extremely necessary for such fibre. Simulation is fulfilled by frequency domain finite difference method (FDFDM), taking into account all details of realistic index profile with stress applying parts, while the leakage/bend loss occur in the region with complex index, surrounding the fibre. Cutoff and small bend loss are theoretically predicted and experimentally measured with excellent agreement between theory and experiment. Polarisation maintaining ability is measured in the form of conventional h-parameter (7.1·10-6 1/m) for 90-μm diameter fibre with birefringence value only 3.9·10-4.

  10. DESIGN NOTE: Surface microscopy and fibre characterization using a multimode-fibre reflectance microscope

    Science.gov (United States)

    Lukins, P. B.; Rehman, S.; Stevens, G. B.

    2000-04-01

    A remarkably simple scanning infrared surface-reflectance microscope based on a multimode-fibre-coupled diode laser together with straightforward electronics and scanning stage is described. The design does not require alignment and completely avoids the use of objectives, beamsplitters and other optics normally associated with such microscopes. The axial response, resolution and imaging properties for non-interferometric operation are characterized. A geometric model for the transmission of such a microscope using an idealized step/graded-index multimode fibre is presented. This model is used to explain the axial response of the microscope. Finally, a new method for determination of the numerical aperture and index-grading parameter of multimode fibres is proposed. This method is based on the geometric model together with axial-response measurements using the microscope in such a way that the fibre probe is the actual test fibre.

  11. Mechanical processing of bast fibres: The occurrence of damage and its effect on fibre structure

    DEFF Research Database (Denmark)

    Hänninen, Tuomas; Thygesen, Anders; Mehmood, Shahid

    2012-01-01

    Currently, separation processes used for natural fibres for composite reinforcing textiles cause a significant amount of damage to the fibres. Microscopic analysis showed that industrially processed flax (Linum usitassimium L.) fibres contained significantly more defects than green or retted ones...... and that further mechanical processing did not significantly increase the amount of defects. In this study it has been shown, by analysing the degree of polymerisation of cell wall components indirectly by viscosity measurements, that mechanically induced defects do not significantly cleave the cell wall polymers....... Acid hydrolysis, however, induced more degradation of the cell wall polymers in fibres having a greater degree of damage, indicating that that defects are more susceptible to certain chemical reactions and which in turn might cause problems for example, during chemical modification of fibres due...

  12. Effects of Polarization-Maintaining Fibre Degrading on Precision of Fibre Optic Gyroscopes in Radiation Environment

    Institute of Scientific and Technical Information of China (English)

    XIAO Wen; LIU De-Wen; LIU Yang; YI Xiao-Su; CONG Lin

    2008-01-01

    @@ In the space environment, the precision of fibre optic gyroscopes (FOGs) degrades because of space radiation.Photonic components of FOGs axe affected by radiation, especially the polaxization-maintaining (PM) fibre coil.In relation to the space radiation environment characteristic, we have carried out a series of radiation experiments on a PM fibre coil with 60Co radiation source at different dose rates. Based on the experimental results, the formula between the PM-fibre loss and radiation dose rata is built, and the relation between the precision of FOG and radiation dose is obtained accordingly. The results strongly show that the precision of our FOG degrades owing to the attenuation of the polarization-maintaining fibre, which provides theoretical foundation for the radiation-resistant design of the FOG.

  13. Voronoi cells, fractal dimensions and fibre composites.

    Science.gov (United States)

    Summerscales, J.; Guild, F. J.; Pearce, N. R. L.; Russell, P. M.

    2001-02-01

    The use of fibre-reinforced polymer matrix composite materials is growing at a faster rate than the gross domestic product (GDP) in many countries. An improved understanding of their processing and mechanical behaviour would extend the potential applications of these materials. For unidirectional composites, it is predicted that localized absence of fibres is related to longitudinal compression failure. The use of woven reinforcements permits more effective manufacture than for unidirectional fibres. It has been demonstrated experimentally that compression strengths of woven composites are reduced when fibres are clustered. Summerscales predicted that clustering of fibres would increase the permeability of the reinforcement and hence expedite the processing of these materials. Commercial fabrics are available which employ this concept using flow-enhancing bound tows. The net effect of clustering fibres is to enhance processability whilst reducing the mechanical properties. The effects reported above were qualitative correlations. To improve the design tools for reinforcement fabrics we have sought to quantify the changes in the micro/meso-structure of woven reinforcement fabrics. Gross differences in the appearance of laminate sections are apparent for different weave styles. The use of automated image analysis is essential for the quantification of subtle changes in fabric architecture. This paper considers Voronoi tessellation and fractal dimensions for the quantification of the microstructures of woven fibre-reinforced composites. It reviews our studies in the last decade of the process-property-structure relationships for commercial and experimental fabric reinforcements in an attempt to resolve the processing vs. properties dilemma. A new flow-enhancement concept has been developed which has a reduced impact on laminate mechanical properties.

  14. Latest developments in silica fibre luminescence dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, D. A.; Abdul S, S. F.; Jafari, S. M.; Alanazi, A. [University of Surrey, Department of Physics, GU2 7XH Guildford, Surrey (United Kingdom); Amouzad M, G. [University of Malaya, Faculty of Engineering, Department of Electrical Engineering, Integrated Lightwave Research Group, 50603 Kuala Lumpur (Malaysia); Addul R, H. A.; Mizanur R, A. K. M.; Zubair, H. T.; Begum, M.; Yusoff, Z.; Omar, N. Y. M. [Multimedia University, Faculty of Engineering, 2010 Cyberjaya, Selangor (Malaysia); Maah, M. J. [University of Malaya, Department of Chemistry, 50603 Kuala Lumpur (Malaysia); Collin, S. [National Physical Laboratory, Hampton Road, Teddington, TW11 OLW Middlesex (United Kingdom); Mat-Sharif, K. A.; Muhd-Yassin, S. Z.; Zulkifli, M. I., E-mail: d.a.bradley@surrey.ac.uk [Telekom Malaysia Research and Development Sdn Bhd., 63000 Cyberjaya, Selangor (Malaysia)

    2015-10-15

    Full text: Using tailor made sub-mm diameter doped-silica fibres, we are carrying out luminescence dosimetry studies for a range of situations, including thermoluminescence (Tl)investigations on a liquid alpha source formed of {sup 223}RaCl (the basis of the Bayer Health care product Xofigo), the Tl response to a 62 MeV proton source and Tl response to irradiation from an {sup 241}Am-Be neutron source. In regard to the former, in accord with the intrinsic high linear energy transfer (Let) and short path length (<100 um) of the α-particles in calcified tissue, the product is in part intended as a bone-seeking radionuclide for treatment of metastatic cancer, offering high specificity and efficacy. The Tl yield of Ge-doped SiO{sub 2} fibres has been investigated including for photonic crystal fibre un collapsed, flat fibres and single mode fibres, these systems offering many advantages over conventional passive dosimetry types. In particular, one can mention comparable and even superior sensitivity, an effective atomic number Z{sub eff} of the silica dosimetric material close to that of bone, and the glassy nature of the fibres offering the additional advantage of being able to place such dosimeters directly into liquid environments. Finally we review the use of our tailor made fibres for on-line radioluminescence measurements of radiotherapy beams. The outcome from these various lines of research is expected to inform development of doped fiber radiation dosimeters of versatile utility, ranging from clinical applications through to industrial studies and environmental evaluations. (Author)

  15. Microanalytical investigation of fibre-reinforced ceramic materials

    Energy Technology Data Exchange (ETDEWEB)

    Meier, B.; Grathwohl, G.

    1989-03-01

    Microanalytical investigations have been made on samples of ceramic fibres (SiC fibres, (Nicalon) C fibre coated with TiN) and fibre-reinforced ceramics (SiC-and glass-matrices). High resolution Auger electron spectroscopy (HRAES), electron probe microanalysis (EPMA) and scanning electron microscopy were employed for these examinations. Analysis was best performed with HRAES on account of its lateral and depth resolution. Some of the problems involved in this technique are discussed e.g. electron beam effects. AES depth profiles of ceramic fibres are reported and compared with the surface analysis of fibres in the composites after being broken in situ.

  16. Influence of the Testing Gage Length on the Strength, Young's Modulus and Weibull Modulus of Carbon Fibres and Glass Fibres

    Directory of Open Access Journals (Sweden)

    Luiz Claudio Pardini

    2002-10-01

    Full Text Available Carbon fibres and glass fibres are reinforcements for advanced composites and the fiber strength is the most influential factor on the strength of the composites. They are essentially brittle and fail with very little reduction in cross section. Composites made with these fibres are characterized by a high strength/density ratio and their properties are intrisically related to their microstructure, i.e., amount and orientation of the fibres, surface treatment, among other factors. Processing parameters have an important role in the fibre mechanical behaviour (strength and modulus. Cracks, voids and impurities in the case of glass fibres and fibrillar misalignments in the case of carbon fibres are created during processing. Such inhomogeneities give rise to an appreciable scatter in properties. The most used statistical tool that deals with this characteristic variability in properties is the Weibull distribution. The present work investigates the influence of the testing gage length on the strength, Young's modulus and Weibull modulus of carbon fibres and glass fibres. The Young's modulus is calculated by two methods: (i ASTM D 3379M, and (ii interaction between testing equipment/specimen The first method resulted in a Young modulus of 183 GPa for carbon fibre, and 76 GPa for glass fibre. The second method gave a Young modulus of 250 GPa for carbon fibre and 50 GPa for glass fibre. These differences revelead differences on how the interaction specimen/testing machine can interfere in the Young modulus calculations. Weibull modulus can be a tool to evaluate the fibre's homogeneity in terms of properties and it is a good quality control parameter during processing. In the range of specimen gage length tested the Weibull modulus for carbon fibre is ~ 3.30 and for glass fibres is ~ 5.65, which indicates that for the batch of fibres tested, the glass fibre is more uniform in properties.

  17. GLUT4 expression at the plasma membrane is related to fibre volume in human skeletal muscle fibres

    DEFF Research Database (Denmark)

    Gaster, M; Vach, W; Beck-Nielsen, H

    2002-01-01

    In this study we examined the relationship between GLUT4 expression at the plasma membrane and muscle fibre size in fibre-typed human muscle fibres by immunocytochemistry and morphometry in order to gain further insight into the regulation of GLUT4 expression. At the site of the plasma membrane......, GLUT4 was more abundantly expressed in slow as compared to fast fibres at the same fibre diameter (p diabetic and obese was reduced...... compared to control subjects at the same diameter (p diabetic subjects expressed a fibre-volume-dependent GLUT4 expression (p diabetic p = 0.06). Our results show that increasing...

  18. Plant fibre composites - porosity and stiffness

    DEFF Research Database (Denmark)

    Madsen, Bo; Thygesen, Anders; Lilholt, Hans

    2009-01-01

    Plant fibre composites contain typically a relatively large amount of porosity which influences their performance. A model, based on a modified rule of mixtures, is presented to include the influence of porosity on the composite stiffness. The model integrates the volumetric composition of the co......Plant fibre composites contain typically a relatively large amount of porosity which influences their performance. A model, based on a modified rule of mixtures, is presented to include the influence of porosity on the composite stiffness. The model integrates the volumetric composition...... of the composites with their mechanical properties. The fibre weight fraction is used as an independent parameter to calculate the complete volumetric composition. A maximum obtainable stiffness of the composites is calculated at a certain transition fibre weight fraction, which is characterised by a best possible...... combination of high fibre volume fraction and low porosity. The model is validated with experimental data from the literature on several types of composites. A stiffness diagram is presented to demonstrate that the calculations can be used for tailoring and design of composites with a given profile...

  19. A large Scintillating Fibre Tracker for LHCb

    Science.gov (United States)

    Greim, R.

    2017-02-01

    The LHCb experiment will be upgraded during LHC Long Shutdown 2 to be able to record data at a higher instantaneous luminosity. The readout rate is currently limited to 1 MHz by the Level 1 trigger. In order to achieve the target integrated luminosity of 50 fb-1 during LHC Run 3, all subdetectors have to be read out by a 40 MHz trigger-less readout system. Especially, the current tracking detectors downstream of the LHCb dipole magnet suffer from large detector dead times and a small granularity in the Outer Tracker, which consists of proportional straw tubes. Therefore, the Downstream Tracker will be replaced by a Scintillating Fibre Tracker with Silicon Photomultiplier readout. The total sensitive area of 340 m2 is made up of 2.5 m long fibre mats consisting of six staggered layers of 250 μm thin scintillating fibres. The scintillation light created by the charged particles traversing the fibre mats is transported to the fibre ends via total internal reflection and detected by state-of-the-art multi-channel SiPM arrays. This paper presents the detector concept, design, challenges, custom-made readout chips, as well as laboratory and beam test results.

  20. Mechanical Property Analysis on Sandwich Structured Hybrid Composite Made from Natural Fibre, Glass Fibre and Ceramic Fibre Wool Reinforced with Epoxy Resin

    Science.gov (United States)

    Bharat, K. R.; Abhishek, S.; Palanikumar, K.

    2017-06-01

    Natural fibre composites find wide range of applications and usage in the automobile and manufacturing industries. They find lack in desired properties, which are required for present applications. In current scenario, many developments in composite materials involve the synthesis of Hybrid composite materials to overcome some of the lacking properties. In this present investigation, two sandwich structured hybrid composite materials have been made by reinforcing Aloe Vera-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and Sisal fibre-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and its mechanical properties such as Tensile, Flexural and Impact are tested and analyzed. The test results from the two samples are compared and the results show that sisal fibre reinforced hybrid composite has better mechanical properties than aloe vera reinforced hybrid composite.

  1. EDITORIAL: Optical Fibre Sensors 18 (OFS-18)

    Science.gov (United States)

    Jones, Julian D. C.; Tatam, Ralph P.

    2007-10-01

    The International Conference on Optical Fibre Sensors (OFS-18) was held in October 2006 in Cancún, Mexico, under the general chairmanship of Dr Alexis Mendez (MCH Engineering LLC, USA) and Dr Fernando Mendoza (Centro de Investigaciones en Optica, Mexico). 'OFS', as it has become known, is firmly established as the leading international conference for the optical fibre sensor community. Since its inception, in London in 1983, and under the leadership of an international steering committee independent of any learned society or professional institution, it has been held approximately every eighteen months. The venue nominally rotates from Europe, to the Americas, and thence to Asia and the Pacific. OFS-18 demonstrated the continuing vigour of the community, with some 250 papers presented, plus two workshops, with attendance as international as ever. In recent years, it has become a tradition to publish a post-conference special issue in the journal Measurement Science and Technology, and these special issues offer a representative sample of the current status of the field. In the nearly 25 years since OFS began, many of the early ideas and laboratory-based proof-of-principle experiments have led to highly developed instrumentation systems, and to successful commercial products. Perhaps the most mature of all of these technologies is the optical fibre gyroscope, with the fibre hydrophone a close second—originally developed for defence applications for which it is now established, but with increasing relevance to the oil and gas industry; electromagnetic sensors based on the Faraday and electro-optic effects are of growing significance in the power generation and distribution industry; whilst in-fibre grating-based sensors occupy an expanding niche in structural monitoring, especially in civil engineering. It is therefore appropriate that the first day of OFS was devoted to workshops on structural health monitoring, and to commemorate the 30th anniversary of the

  2. Fatigue processes in thermoplastic fibres; Les mecanismes de fatigue dans les fibres thermoplastiques

    Energy Technology Data Exchange (ETDEWEB)

    Herrera Ramirez, J.M.

    2004-09-15

    The present study examines and compares the behaviour of the two types of PA66 fibres and two types of PET fibres under fatigue loading up to failure, and the correlation between the fibres (nano)structures and their structural heterogeneities, with fatigue lifetimes. Several techniques have been used to analyze the materials, such as scanning electron microscopy (SEM), microanalysis (EDS), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and micro-Raman spectroscopy. A meticulous analysis by scanning electron microscopy of the fracture morphology of fibres broken in tension and in fatigue, as well as a study of the fatigue life, were undertaken. The fatigue process occurs when the cyclic load amplitude is sufficiently large, however a condition for fatigue failure is that the minimum load each cycle must be lower than a threshold stress level. Failure under fatigue conditions leads to distinctive fracture morphologies which are very different from those seen after tensile or creep failure and this allows easy identification of the fatigue process. The fibres have been analyzed in the as received state and after fatigue failure in order to observe the microstructural changes resulting from the fatigue loading. The results will be compared with those obtained for fibres loaded under conditions where the fatigue process was hindered. The role of the microstructure of the fibres in determining fatigue will be discussed in this work and the possibility of improving their resistance to fatigue or eliminating the fatigue process will be discussed. (author)

  3. Study of injection moulded long glass fibre-reinforced polypropylene and the effect on the fibre length and orientation distribution

    Science.gov (United States)

    Parveeen, B.; Caton-Rose, P.; Costa, F.; Jin, X.; Hine, P.

    2014-05-01

    Long glass fibre (LGF) composites are extensively used in manufacturing to produce components with enhanced mechanical properties. Long fibres with length 12 to 25mm are added to a thermoplastic matrix. However severe fibre breakage can occur in the injection moulding process resulting in shorter fibre length distribution (FLD). The majority of this breakage occurs due to the melt experiencing extreme shear stress during the preparation and injection stage. Care should be taken to ensure that the longer fibres make it through the injection moulding process without their length being significantly degraded. This study is based on commercial 12 mm long glass-fibre reinforced polypropylene (PP) and short glass fibre Nylon. Due to the semi-flexiable behaviour of long glass fibres, the fibre orientation distribution (FOD) will differ from the orientation distribution of short glass fibre in an injection molded part. In order to investigate the effect the change in fibre length has on the fibre orientation distribution or vice versa, FOD data was measured using the 2D section image analyser. The overall purpose of the research is to show how the orientation distribution chnages in an injection moulded centre gated disc and end gated plaque geometry and to compare this data against fibre orientation predictions obtained from Autodesk Moldflow Simulation Insight.

  4. Pulse Compression And Raman Amplification In Optical Fibres

    Science.gov (United States)

    Byron, Kevin C.

    1988-06-01

    Experimental and theoretical investigations on Raman amplification in fibres have been carried out and simultaneous amplification and pulse compression observed. With a fibre design optimised for amplification high gain may be obtained at practical pump power levels.

  5. Mechanical Properties of Man-Made Mineral glass fibres

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    In nature basaltic volcanic glass fibres are know from Hawaii as Pele's hair, formed by droplets of lava thrown into the air during volcanic eruption. The concept of glass fibre formation by an air stream dragging fibres from drops of melt is copied in industry to form basaltic glass wool fibres......; man-made mineral glass fibres. The basaltic melt is prevented from crystallizing due to the high cooling rate, forming the mineral glass wool fibres. Basaltic mineral wool fibres are of high interest in industry due to their good chemical durability and excellent heat and sound insulation properties...... of the information gained from the mechanical tests, fracture characteristics of individual glass fibres are imaged by scanning electron microscopy. The fracture surfaces showed to fall in three groups; 1) surfaces including fracture mirror, mist and hackle, 2) bend fracture surfaces and 3) surfaces including pores...

  6. Fibre-Optic Strain Measurement For Structural Integrity Monitoring

    NARCIS (Netherlands)

    Bruinsma, A.J.A.; Zuylen, P. van; Lamberts, C.W.; Krijger, A.J.T. de

    1984-01-01

    A method is demonstrated for monitoring the structural integrity of large structures, using an optical fibre. The strain distribution along the structure is monitored by measuring the attentuation of light along the length of the fibre.

  7. Microstructure and Mechanical Properties of Aligned Natural Fibre Composites

    DEFF Research Database (Denmark)

    Rask, Morten

    properties (stiffness-to-density ratio). The perspective of using natural fibres is to have a sustainable, biodegradable, CO2-neutral alternative to glass fibres. However, so far, it has not been possible to take full advantage of the natural fibre properties when using them for composite applications......Recently, there has been a great interest in developing and maturing natural fibre composites for structural applications. Natural fibres derived from plants such as flax and hemp have the potential to compete with traditional glass fibres as reinforcements in polymer matrices, due to good specific....... Several challenges have to be addressed and solved, many of which pertain to the fact that the fibres are sourced from a natural resource: 1) Inconsistent properties, depending on plant species, growth and harvest conditions, and fibre extraction techniques. 2) Strength values of composites are lower than...

  8. On the behaviour of gelled fibre suspensions in steady shear

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, Bettina [Unilever Corporate Research, Bedford (United Kingdom); University of Nottingham, Division of Food Sciences, Loughborough (United Kingdom); White, Duncan; Melrose, John R.; Frith, William J. [Unilever Corporate Research, Bedford (United Kingdom)

    2007-03-15

    The shear rheological properties of suspensions of gelled agar fibres in a low viscosity Newtonian matrix fluid were investigated. Two classes of fibres, low aspect ratio fibres and high aspect ratio fibres with an aspect ratio of the order of 10 and 100 respectively were included in the investigations. For all fibre phase volumes investigated, from as low as 0.01 upwards, the flow curves are characterised by an apparent yield stress followed by shear-thinning which was independent of the fibre aspect ratio. Based on our analysis of the flow curves, we conclude that the high aspect ratio fibres behave like flexible threads in contrast to the low aspect ratio fibres whose high shear relative viscosity is successfully described by a relation for long rigid rods. These findings are supported by flow visualisation using an optical shearing stage coupled to a light microscope. (orig.)

  9. The in vivo biological activity of ceramic fibres.

    Science.gov (United States)

    Brown, R C; Hoskins, J A; Glass, L R

    1995-10-01

    The well-known health effects following exposure to amphibole asbestos have led to some concern about the potential for other fibrous materials to cause similar diseases. This paper presents a summary of some of the inhalation experiments conducted with ceramic fibres in both rats and hamsters at the Research and Consulting Company, Geneva. One ceramic fibre (designated RCF1) was tested in rats at four exposure levels, this fibre was also tested in hamsters. Three other fibres were only tested in rats at the highest level--30 mg m-3. The increased incidence of tumours in these experiments has been contrasted with the negative results obtained with glass or mineral wools. However, there is evidence that the ceramic fibres were longer than the glass fibres and that long ceramic fibres were retained in lung tissue to a greater extent. This is sufficient to explain the results without recourse to explanations based on chemical differences between fibres.

  10. Rare Earth Doped Optical Fibre From Oxide Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Minati Chatterjee; Aharon Gedanken; Renata Reisfeld; Ranjan Sen; Mrinmay Pal; Milan Naskar; Mukul Paul; Shyamal Bhadra; Kamal Dasgupta; Dibyendu Ganguli; Tarun Bandyopadhyay

    2003-01-01

    Rare earth (RE) doped optical fibres were fabricated by using RE oxides coated silica nanoparticles. The fibre properties are comparable to those prepared by conventional techniques. The process offers better control over RE incorporation and homogeneity in the preform.

  11. Special Polymer Optical Fibres and Devices for Photonic Applications

    Institute of Scientific and Technical Information of China (English)

    Gang-Ding Peng

    2003-01-01

    Remarkable progresses have been made in developing special polymer optical fibres and devices for photonic applications in recent years. This presentation will mainly report on the development of electro-optic, photosensitive and photorefractive polymer optical fibres and related devices.

  12. Manufacturing Titanium Metal Matrix Composites by Consolidating Matrix Coated Fibres

    Institute of Scientific and Technical Information of China (English)

    Hua-Xin PENG

    2005-01-01

    Titanium metal matrix composites (TiMMCs) reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre (MCF) method offer optimum properties because of the resulting uniform fibre distribution, minimum fibre damage and fibre volume fraction control. In this paper, the consolidation of Ti-6Al-4V matrix-coated SiC fibres during vacuum hot pressing has been investigated. Experiments were carried out on multi-ply MCFs under vacuum hot pressing (VHP). In contrast to most of existing studies, the fibre arrangement has been carefully controlled either in square or hexagonal arraysthroughout the consolidated sample. This has enabled the dynamic consolidation behaviour of MCFs to be demonstrated by eliminating the fibre re-arrangement during the VHP process. The microstructural evolution of the matrix coating was reported and the deformation mechanisms involved were discussed.

  13. Turbulence hierarchy in a random fibre laser

    Science.gov (United States)

    González, Iván R. Roa; Lima, Bismarck C.; Pincheira, Pablo I. R.; Brum, Arthur A.; Macêdo, Antônio M. S.; Vasconcelos, Giovani L.; de S. Menezes, Leonardo; Raposo, Ernesto P.; Gomes, Anderson S. L.; Kashyap, Raman

    2017-05-01

    Turbulence is a challenging feature common to a wide range of complex phenomena. Random fibre lasers are a special class of lasers in which the feedback arises from multiple scattering in a one-dimensional disordered cavity-less medium. Here we report on statistical signatures of turbulence in the distribution of intensity fluctuations in a continuous-wave-pumped erbium-based random fibre laser, with random Bragg grating scatterers. The distribution of intensity fluctuations in an extensive data set exhibits three qualitatively distinct behaviours: a Gaussian regime below threshold, a mixture of two distributions with exponentially decaying tails near the threshold and a mixture of distributions with stretched-exponential tails above threshold. All distributions are well described by a hierarchical stochastic model that incorporates Kolmogorov's theory of turbulence, which includes energy cascade and the intermittence phenomenon. Our findings have implications for explaining the remarkably challenging turbulent behaviour in photonics, using a random fibre laser as the experimental platform.

  14. TAIPAN fibre feed and spectrograph: engineering overview

    Science.gov (United States)

    Staszak, Nicholas F.; Lawrence, Jon; Zhelem, Ross; Content, Robert; Churilov, Vladimir; Case, Scott; Brown, Rebecca; Hopkins, Andrew M.; Kuehn, Kyler; Pai, Naveen; Klauser, Urs; Nichani, Vijay; Waller, Lew

    2016-07-01

    TAIPAN will conduct a stellar and galaxy survey of the Southern sky. The TAIPAN positioner is being developed as a prototype for the MANIFEST instrument on the GMT. The TAIPAN Spectrograph is an AAO designed all-refractive 2-arm design that delivers a spectral resolution of R>2000 over the wavelength range 370-870 nm. It is fed by a custom fibre cable from the TAIPAN Starbugs positioner. The design for TAIPAN incorporates 150 optical fibres (with an upgrade path to 300). Presented is an engineering overview of the UKST Fibre Cable design used to support Starbugs, the custom slit design, and the overall design and build plan for the TAIPAN Spectrograph.

  15. Development of SERS active fibre sensors

    CERN Document Server

    Polwart, E

    2002-01-01

    Surface-enhanced Raman scattering (SERS) is sensitive and selective and when coupled with fibre-optics could potentially produce an effective chemical sensing system. This thesis concerns the development of a single-fibre-based sensor, with an integral SERS-active substrate. A number of different methods for the manufacture of SERS-active surfaces on glass substrates were investigated and compared. The immobilisation of metal nanoparticles on glass functionalised with (3-aminopropyl)trimethoxysilane emerged as a suitable approach for the production of sensors. Substrates prepared by this approach were characterised using UV-visible spectroscopy, electron microscopy and Raman mapping. It was found that exposure of substrates to laser radiation led to a decrease in the signal recorded from adsorbed analytes. This speed of the decrease was shown to depend on the analyte, and the exciting wavelength and power. SERS-active fibre sensors were produced by immobilisation of silver nanoparticles at the distal end of a...

  16. Optical fibre cantilever sensor for biological application

    Science.gov (United States)

    Li, J.; Zhou, Y. X.; Patterson, G.; Shu, W. M.; Maier, R. R. J.; Fowler, R.; Hand, D. P.; MacPherson, W. N.

    2014-05-01

    Micro-cantilever sensors have shown great promise in a wide range of application are as including chemical and biological sensing. However, many of these devices are based upon a sensor `chip' that requires careful alignment between the cantilever and the read-out system, which can be challenging. Furthermore, optical interrogation typically involves a bulky free-space system. Optical fibre addressed cantilevers have been reported previously in the literature and in this paper we propose techniques to design and fabricate polymer micro-cantilevers for attachment onto the end of standard single mode fibres using laser machining. Low-cost optical sources and a fibre coupled spectrometer are employed to monitor the cantilever deflection and therefore observe biological binding between a species of interest and an activated cantilever. Proof-of-concept experiments show that the sensor is capable of detecting pathogen concentration with down to a level of 105cfu/ml.

  17. Secure Communication System Basedon Chaosin Optical Fibre

    Institute of Scientific and Technical Information of China (English)

    Pak L Chu; Fan Zhang; William Mak; Robust Lai

    2003-01-01

    @@ 1 Introduction Recently, there have been intense research activities on the study of synchronized chaos generated by fibre lasers [1] and its application to secure communication systems . So far, all studies concentrate on two aspects:[2].So far,all studies concentrate on two aspects:(1) the effect of the transmission channel between the transmitter and the receiver has been neglected, and (2)the chaos and the signal are carried by one wavelength.Both theoretical and experimental investigations make these two assumptions. In the experiments, the transmission fibre is invariably short, in the order of tens of metres. Hence its dispersion and nonlinear effects are negligible. The fibre laser responsible for the generation of chaos is often designed to lase at one wavelength only.

  18. Space Division Multiplexing in Optical Fibres

    CERN Document Server

    Richardson, D J; Nelson, L E

    2013-01-01

    Optical communications technology has made enormous and steady progress for several decades, providing the key resource in our increasingly information-driven society and economy. Much of this progress has been in finding innovative ways to increase the data carrying capacity of a single optical fibre. In this search, researchers have explored (and close to maximally exploited) every available degree of freedom, and even commercial systems now utilize multiplexing in time, wavelength, polarization, and phase to speed more information through the fibre infrastructure. Conspicuously, one potentially enormous source of improvement has however been left untapped in these systems: fibres can easily support hundreds of spatial modes, but today's commercial systems (single-mode or multi-mode) make no attempt to use these as parallel channels for independent signals.

  19. Mineral fibre problems: a management view.

    Science.gov (United States)

    Hardie, H D

    1980-01-01

    Fibre is a form of matter that imparts exclusive properties to end-products; however, most fibres have been associated with health problems. Although management has a responsibility to ensure the safety of products and processes, data on which to base risk-equation decisions are often inadequate. The limitations of current dust measurement technology suggest that apparently precise numerical exposure data are as subjective as use of the terms 'heavy', 'moderate' or 'light'. Control of any useful but hazardous material is preferable to the ultimate sanction of prohibition. The man-made mineral fibre industry and national and international regulatory agencies should learn from the asbestos industry. It is suggested that a process of consultation, rather than one of confrontation, is more likely to produce widely acceptable solutions in each generation.

  20. Laser acceleration... now with added fibre

    CERN Document Server

    Katarina Anthony

    2012-01-01

    Laser acceleration technology is plagued by two main issues: efficiency and repetition rates. In other words, lasers consume too much power and cannot sustain accelerating particles long enough to produce collisions. ICAN, a new EU-funded project, is examining how fibre lasers may help physicists tackle these issues.   A diode-pumped fibre laser. (Image courtesy of Laser Zentrum Hannover.) The International Coherent Amplification Network (ICAN) is studying the potential of lasers for collision physics. CERN is a beneficiary of the project and will collaborate with 15 other institutes from around the world, including KEK in Japan, Fermilab in the USA, and DESY in Germany. “The network is looking into existing fibre laser technology, which we believe has fantastic potential for accelerators,” says Gerard Mourou, ICAN co-ordinator at the École Polytechnique in France. “The hope is to make laser acceleration competitive with traditional radio-fre...

  1. Interfaces between a fibre and its matrix

    DEFF Research Database (Denmark)

    Lilholt, Hans; Sørensen, Bent F.

    2017-01-01

    The interface between a fibre and its matrix represents an important element in the characterization and exploitation of composite materials. Both theoretical models and analyses of experimental data have been presented in the literature since modern composite were developed and many experiments...... have been performed. A large volume of results for a wide range of composite systems exists, but rather little comparison and potential consistency have been reached for fibres and/or for matrices. Recently a materials mechanics approach has been presented to describe the interface by three parameters...... in polyester matrix. The analysis of existing experimental literature data is demonstrated for steel fibres in epoxy matrix and for tungsten wires in copper matrix. These latter incomplete analyses show that some results can be obtained even if all three experimental parameters are not recorded....

  2. Presynaptic calcium signalling in cerebellar mossy fibres

    Directory of Open Access Journals (Sweden)

    Louiza B Thomsen

    2010-02-01

    Full Text Available Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A TTX-sensitive fast Na+ spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers. Calcium imaging using Calcium-Green dextran revealed a stimulus-evoked all-or-none tetrodotoxin (TTX -sensitive calcium signal in simple and complex rosettes. All compartments of a complex rosette were activated during electrical activation of the mossy fibre, while individual simple and complex rosettes along an axon appeared to be isolated from one another in terms of calcium signalling. CGP55845 application showed that GABA B receptors mediated presynaptic inhibition of the calcium signal over the entire firing frequency range of mossy fibres. A paired-pulse depression of the calcium signal lasting more than one second affected burst firing in mossy fibres; this paired-pulse depression was reduced by GABA B antagonists. While our results indicated that a presynaptic rosette electrophysiologically functioned as a unit, topical GABA application showed that calcium signals in the branches of complex rosettes could be modulated locally, suggesting that cerebellar glomeruli may be dynamically sub-compartmentalized due to ongoing inhibition mediated by Golgi cells. This could provide a fine-grained control of mossy fibre-granule cell information transfer and synaptic plasticity within a mossy fibre rosette.

  3. FOAM CONCRETE REINFORCEMENT BY BASALT FIBRES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-10-01

    Full Text Available The authors demonstrate that the foam concrete performance can be improved by dispersed reinforcement, including methods that involve basalt fibres. They address the results of the foam concrete modeling technology and assess the importance of technology-related parameters. Reinforcement efficiency criteria are also provided in the article. Dispersed reinforcement improves the plasticity of the concrete mix and reduces the settlement crack formation rate. Conventional reinforcement that involves metal laths and rods demonstrates its limited application in the production of concrete used for thermal insulation and structural purposes. Dispersed reinforcement is preferable. This technology contemplates the infusion of fibres into porous mixes. Metal, polymeric, basalt and glass fibres are used as reinforcing components. It has been identified that products reinforced by polypropylene fibres demonstrate substantial abradability and deformability rates even under the influence of minor tensile stresses due to the low adhesion strength of polypropylene in the cement matrix. The objective of the research was to develop the type of polypropylene of D500 grade that would demonstrate the operating properties similar to those of Hebel and Ytong polypropylenes. Dispersed reinforcement was performed by the basalt fibre. This project contemplates an autoclave-free technology to optimize the consumption of electricity. Dispersed reinforcement is aimed at the reduction of the block settlement in the course of hardening at early stages of their operation, the improvement of their strength and other operating properties. Reduction in the humidity rate of the mix is based on the plasticizing properties of fibres, as well as the application of the dry mineralization method. Selection of optimal parameters of the process-related technology was performed with the help of G-BAT-2011 Software, developed at Moscow State University of Civil Engineering. The authors also

  4. Zeonex Microstructured Polymer Optical Fibre Bragg Grating Sensor

    DEFF Research Database (Denmark)

    Woyessa, Getinet; Fasano, Andrea; Markos, Christos

    2016-01-01

    We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time.......We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time....

  5. Fibre Bragg Grating Components for Filtering, Switching and Lasing

    OpenAIRE

    2008-01-01

    Fibre Bragg gratings (FBGs) are key components for a vast number of applications in optical communication systems, microwave photonics systems, and optical sensors, etc. The main topic of this thesis is fibre Bragg grating fabrication and applications in direct microwave optical filtering, high speed switching and switchable dual-wavelength fibre lasers. First, a brief overview is given about the photosensitivity in optical fibre, basic FBG fabrication techniques, the popular coupled-mode the...

  6. Facile synthesis of ZnO hollow fibres

    Indian Academy of Sciences (India)

    B T Su; K Wang; X W Zuo; H M Mu; N Dong; Y C Tong; J Bai; Z Q Lei

    2007-12-01

    In this paper, cotton fibres were used as bio-template to successfully synthesize new ceramic materials, ZnO hollow fibres and in an effort to explore the synthesis condition, and simplify the synthesis procedure. In this synthesis, a direct thermal decomposition of zinc acetate dihydrate coated on the surface of cotton fibres was explored. The wall porosity of the ZnO hollow fibres was controlled by changing the concentration of zinc acetate aqueous solution.

  7. Photonic Crystal Fibres - the State-of-the-Art

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Hansen, K. P.; Hansen, Theis Peter;

    2002-01-01

    Photonic crystal fibres having microstructured air-silica cross sections offer new optical properties compared to conventional fibres. These include novel guiding mechanisms, unique spectral properties and nonlinear possibilities. Recent results within the field are reviewed.......Photonic crystal fibres having microstructured air-silica cross sections offer new optical properties compared to conventional fibres. These include novel guiding mechanisms, unique spectral properties and nonlinear possibilities. Recent results within the field are reviewed....

  8. Mathematical Model for Fabrication of Micro-Structure Fibres

    Institute of Scientific and Technical Information of China (English)

    ZHOU Gui-Yao; HOU Zhi-Yun; LI Shu-Guang; HOU Lan-Tian

    2005-01-01

    @@ Using the classic principles of mechanics, we discuss the shape transformation of the micro-structure fibre preform under high temperature of the fibre drawing process, which leads to the theoretical relations among the structural diameter of the micro-structure fibre, the drawing technical parameter, and the physical constant of the microstructure fibre material. The theoretic values are basically in agreement with the experimental results.

  9. Fibre function and perception during cutaneous nerve block.

    Science.gov (United States)

    Mackenzie, R A; Burke, D; Skuse, N F; Lethlean, A K

    1975-09-01

    In awake human subjects, neural responses in radial nerves to electrical stimulation were recorded with intrafascicular tungsten microelectrodes. Changes in the activity of individual fibre groups during blocking procedures were recorded and correlated with simultaneous alterations in the perception of standardized stimuli. Light touch sensibility in hairy skin appeared to depend on the integrity of A-beta-gamma fibres, cold and pinprick on A-delta fibres, and warmth and dull pain on C fibres.

  10. Fabrication and applications of highly nonlinear silica holey fibres

    OpenAIRE

    Belardi, W.; Monro, T.M.; Price, J.H.V.; Lee, J.H.; Petropoulos, P.; Richardson, D J

    2001-01-01

    Holey fibre (HF) technology provides a new way to fabricate novel highly nonlinear silica based fibres. The cladding of a HF is defined by an arrangement of air holes that run along the fibre length surrounding a central silica core. The reduction in core size and increase in refractive index contrast that is possible in a HF allows the production of fibres with extremely high effective nonlinearity. HFs can also exhibit, by design of the hole configuration [2], dispersion properties not poss...

  11. The Significance of Defects on the Failure of Fibre Composites,

    Science.gov (United States)

    1981-12-01

    effects produced by discontinuous and kinked plies in unidirectional carbon fibre reinforced plastic under tension. The mean stress at failure on the...5 to6.5%) void contents on changes in torsional properties of carbon fibre reinforced plastic when exposed at various temperatures to dry or wet...properties of carbon fibre/Kevlar fibre reinforced plastic hybrid composites." RAE Technical Report 76057 (1976)* 15 G. Dorey, D.J. Portsmouth, Private

  12. Crack Growth Monitoring by Embedded Optical Fibre Bragg Grating Sensors: Fibre Reinforced Plastic Crack Growing Detection

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira; Mikkelsen, Lars Pilgaard; McGugan, Malcolm

    2015-01-01

    This article presents a novel method to asses a crack growing/damage event in fibre reinforced plastic, or adhesive using Fibre Bragg Grating (FBG) sensors embedded in a host material. Different features of the crack mechanism that induce a change in the FBG response were identified. Double...... Cantilever Beams specimens made with glass fibre glued with structural adhesive, were instrumented with an array of FBG sensors embedded in the material and tested using an experimental fracture procedure. A digital image correlation technique was used to determine the presence of the specific phenomena...

  13. Fibre Optical Parametric Amplification in Defect Bragg Fibres with Zero Dispersion Slow Light Effect

    Institute of Scientific and Technical Information of China (English)

    XIAO Li; ZHANG Wei; HUANG Yi-Dong; PENG Jiang-De; ZHAO Hong; YANG Ke-Wu

    2008-01-01

    Nonfinearity enhancement by slow light effect and strong light confinement in defect Bragg fibres is demonstrated and analysed in applications of fibre optical parametric amplifiers. Broadband low group velocity and zero dispersion as well as the strong light confinement by band gap enhances the nonlinear coefficient up to more than one order than the conventional high nonlinear fibres.Moreover,the zero dispersion wavelength of coupled core mode can be designed arbitrarily,under which the phase-matching bandwidth of the nonlinear process can be extended.

  14. Solution electrospinning of particle-composite fibres

    DEFF Research Database (Denmark)

    Christiansen, Lasse; Fojan, Peter

    2016-01-01

    Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio.......Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio....

  15. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1998-01-01

    Durability studies are carried out at BKM as part of the research project "Design Methods for Fibre Reinforced Concrete" (FRC) involving BKM, The Concrete Research Center at DTI, Building Technology at Aalborg University, Rambøll, 4K-Beton and Rasmussen & Schiøtz. Concrete beams with or without...... structure are made on specimens drilled or sawed from beams after unloading (mechanical load). The pore structure of the concretes will be studied by microscopy, sorption and suction curves. The test programme involves three different concrete qualities (water-cement ratios). Both steel fibres (ZP...

  16. High Power Photonic Crystal Fibre Raman Laser

    Institute of Scientific and Technical Information of China (English)

    YAN Pei-Guang; RUAN Shuang-Chen; YU Yong-Qin; GUO Chun-Yu; GUO Yuan; LIU Cheng-Xiang

    2006-01-01

    A cw Raman laser based on a 100-m photonic crystal fibre is demonstrated with up to 3.8 W output power at the incident pump power of 12 W, corresponding to an optical-to-optical efficiency of about 31.6%. The second order Stokes light, which is firstly reported in a cw photonic crystal fibre Raman laser, is obtained at 1183nm with an output power of 1.6 W and a slope efficiency of about 45.7%.

  17. Spinothalamic fibres, pain conduction and cordotomy.

    Science.gov (United States)

    Moffie, D

    1975-01-01

    Description of four cases of cordotomy for intractable pain in which autopsy could be performed. In two of the cases the lesion had been placed (unintentionally) in the posterior quadrant of the spinal cord with good results as to the abolishing of pain. It is concluded that the conduction of pain and temperature stimuli is not restricted to the anterolateral part of the spinal cord but that this conduction may also take place along fibres in the posterolateral quadrant. A further conclusion is that the results of cordotomy are related to the number of cut fibres.

  18. Liquid filling of photonic crystal fibres for grating writing

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Canning, John; Lægsgaard, Jesper;

    2007-01-01

    liquid filling of photonic crystal fibres reduces the scattering from air–glass interfaces during Bragg grating writing in many layered photonic crystal fibres. Within experimental uncertainty, the grating index modulation of a grating written in germanium-doped photonic crystal fibre with 10 rings...

  19. Calculation of the conduction velocity of short nerve fibres

    NARCIS (Netherlands)

    van der Vliet, G.H.; Holsheimer, J.

    1980-01-01

    The conduction velocity v of a nerve fibre is calculated from the time delay Δ of a propagating action potential between two recording sites along the fibre. However, the conventional method of determining Δ cannot be applied to short nerve fibres. Therefore several linear signal analysis methods

  20. Optical fibre Bragg grating recorded in TOPAS cyclic olefin copolymer

    DEFF Research Database (Denmark)

    Johnson, I.P.; Yuan, Scott Wu; Stefani, Alessio

    2011-01-01

    A report is presented on the inscription of a fibre Bragg grating into a microstructured polymer optical fibre fabricated from TOPAS cyclic olefin copolymer. This material offers two important advantages over poly (methyl methacrylate), which up to now has formed the basis for polymer fibre Bragg...

  1. Design of fibre reinforced PV concepts for building integrated applications

    NARCIS (Netherlands)

    Reinders, Angelina H.M.E.; de Wit, H.; de Boer, Andries; Ossenbrink Sinke, W.; Helm, P.

    2009-01-01

    Fibre reinforced polymers present an interesting encapsulation medium for PV-modules. Glass fibres can provide increased strength and stiffness to thin polymer layers overcoming the brittleness and limited deformability of glass-panes. Glass fibre reinforced polymers allows for transparency over a

  2. Mechanical properties of short-flax-fibre reinforced compounds

    NARCIS (Netherlands)

    Bos, H.L.; Müssig, J.; Oever, van den M.J.A.

    2006-01-01

    The mechanical properties of flax/polypropylene compounds, manufactured both with a batch kneading and an extrusion process were determined and compared with the properties of Natural fibre Mat Thermoplastic (NMT) composites. The fibre length and width distributions of the fibres from the compounds

  3. Modelling fibre laydown and web uniformity in nonwoven fabric

    Science.gov (United States)

    Battocchio, F.; Sutcliffe, M. P. F.

    2017-04-01

    The mechanical and functional performance of nonwoven fabric critically depends on the fibre architecture. The fibre laydown process plays a key role in controlling this architecture. The fibre dynamic behaviour during laydown is studied through a finite element model which describes the role of the parameters in defining the area covered by a single fibre when deposited on the conveyor belt. The path taken by a fibre is described in terms of the radius of gyration, which characterises the area covered by the fibre in the textile, and the spectrum of curvature, which describes the degree of fibre looping as a function of the arc length. Starting from deterministic and idealised fibre curvature spectra, stochastic Monte Carlo simulations are undertaken to generate full nonwoven web samples and reproduce the uniformity of fibre density. A novel image analysis technique that allows measurement of the uniformity of real spunbonded nonwoven samples from images of textiles is used to confirm the validity of the model. It is shown that the main parameter that governs the fibre density uniformity is the ratio of the fibre spinning velocity to the velocity of conveyor belt, while fibre oscillations prior to deposition play a secondary role.

  4. Wet spinning of asymmetric hollow fibre membranes for gas separation

    NARCIS (Netherlands)

    Hof, van 't Jacob Adriaan

    1988-01-01

    This thesis describes the spinning and characterizatin of hollow fibre membranes for gas separation. The type of fibres studied here are made by a wet spinning process. A homogeneous solution is prepared, consisting of a polymer in a suitable organic solvent, and extruded as a hollow fibre. Both the

  5. Environmental impact assessment of man-made cellulose fibres

    NARCIS (Netherlands)

    Shen, L.; Worrell, E.; Patel, M.K.

    2010-01-01

    Man-made cellulose fibres have played an important role in the production of textile products for more than 70 years. The purpose of this study is to assess the environmental impact of man-made cellulose fibres. Life cycle assessment (LCA) was conducted for three types of fibres (i.e. Viscose, Modal

  6. Wet spinning of asymmetric hollow fibre membranes for gas separation

    NARCIS (Netherlands)

    van 't Hof, Jacob Adriaan

    1988-01-01

    This thesis describes the spinning and characterizatin of hollow fibre membranes for gas separation. The type of fibres studied here are made by a wet spinning process. A homogeneous solution is prepared, consisting of a polymer in a suitable organic solvent, and extruded as a hollow fibre. Both the

  7. Environmental impact assessment of man-made cellulose fibres

    NARCIS (Netherlands)

    Shen, L.; Worrell, E.; Patel, M.K.

    2010-01-01

    Man-made cellulose fibres have played an important role in the production of textile products for more than 70 years. The purpose of this study is to assess the environmental impact of man-made cellulose fibres. Life cycle assessment (LCA) was conducted for three types of fibres (i.e. Viscose, Modal

  8. CLEAVAGE OF SOFTWOOD KRAFT PULP FIBRES BY HCL AND CELLULASES

    Directory of Open Access Journals (Sweden)

    Paul Ander

    2008-05-01

    Full Text Available A new pulp fibre testing procedure called the HCl method was used to compare different spruce and pine fibres and mixtures of these fibres to calculate number of fibre cleavages in dislocations and other weak points. This method was compared with treatment of softwood kraft pulp fibres using different cellulase mixtures. The HCl method can distinguish between mill- and laboratory-made softwood kraft pulp fibres from the same wood batch. The sugar release is characterized by xylose and other hemicellulose sugars and little glucose. This is in contrast to cellulases, which despite strong fibre cleavage, did not distinguish between mill- and laboratory-made pulp fibres and released large amounts of glucose from the fibres. Hemicellulose degradation by HCl and deep penetration of the acid into the primary and secondary fibre cell walls at 80°C seems to be of major importance for the differentiation between mill and laboratory pulp fibres. Cellulases, in contrast, act mostly on the fibre surfaces, and deep penetration only takes place in amorphous regions of dislocations.

  9. Design of fibre reinforced PV concepts for building integrated applications

    NARCIS (Netherlands)

    Reinders, A.H.M.E.; Wit, de H.; Boer, de A.

    2009-01-01

    Fibre reinforced polymers present an interesting encapsulation medium for PV-modules. Glass fibres can provide increased strength and stiffness to thin polymer layers overcoming the brittleness and limited deformability of glass-panes. Glass fibre reinforced polymers allows for transparency over a b

  10. Biodegradable hollow fibres for the controlled release of hormones

    NARCIS (Netherlands)

    Eenink, M.J.D.; Feijen, Jan; Olijslager, J.; Albers, J.H.M.; Rieke, J.C.; Greidanus, P.J.

    1987-01-01

    Poly(l-lactide), (PLLA), hollow fibres were prepared using a dry-wet phase inversion spinning process. The effect of several spinning parameters (i.e. bore medium flow rate, spinning dope extrusion rate, fibre take-up rate, and spinning height) on the hollow fibre dimensions is reported. The use of

  11. Biodegradable hollow fibres for the controlled release of hormones

    NARCIS (Netherlands)

    Eenink, M.J.D.; Feijen, J.; Olijslager, J.; Albers, J.H.M.; Rieke, J.C.; Greidanus, P.J.

    1987-01-01

    Poly(l-lactide), (PLLA), hollow fibres were prepared using a dry-wet phase inversion spinning process. The effect of several spinning parameters (i.e. bore medium flow rate, spinning dope extrusion rate, fibre take-up rate, and spinning height) on the hollow fibre dimensions is reported. The use of

  12. Surface charges in blending short fibres with polyethylene powder

    NARCIS (Netherlands)

    Hofste, JM; Kersten, MJE; van Turnhout, J; Pennings, AJ

    1998-01-01

    Short fibres and ultra-high molecular weight polyethylene (UHMWPE) powder were mixed by swirling in a glass jar with compressed nitrogen. It was found that a kind of attraction between the fibres and UHMWPE particles is crucial for making a composite with a proper fibre distribution. If aramid and U

  13. Tensile behaviour of polyethylene and poly(p-xylylene) fibres

    NARCIS (Netherlands)

    van der Werff, Harm

    1991-01-01

    This thesis deals with the tensile behaviour of fibres prepared from high molecular weight polymers.The tensile strength of a polymeric fibre is in general much lower than the corresponding theoretical value. In case of ultra-high molecular weight polyethylene (UHMWPE), fibres can be prepared by gel

  14. Microbending in photonic crystal fibres - an ultimate loss limit?

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Hansen, Theis Peter; Hougaard, Kristian G.;

    2001-01-01

    Microbending losses are for the first time estimated in index-guiding photonic crystal fibres, and comparisons with standard step-index fibres are made. The results indicate that typical photonic crystal fibres are significantly less sensitive (one order of magnitude smaller loss) towards...

  15. Determinants and clinical application of muscle fibre conduction velocity

    NARCIS (Netherlands)

    Blijham, P.J.

    2007-01-01

    A muscle fibre can be excited by electrical stimulation using a needle electrode. Action potentials elicited this way will be conducted through the muscle fibre and can be recorded at some distance with a second needle electrode. This way, muscle fibre conduction velocity can be estimated. In the pr

  16. Nd3+ Doped Silicate Glass Photonic Crystal Fibres

    Institute of Scientific and Technical Information of China (English)

    YANG Lu-Yun; CHEN Dan-Ping; XIA Jin-An; WANG Chen; JIANG Xiong-Wei; ZHU Cong-Shan; QIU Jian-Rong

    2005-01-01

    @@ We report on the fabrication of two kinds of large core area Nd3+ doped silicate glass photonic crystal fibres, and demonstration of the fibre waveguiding properties. The measured minimum loss of one kind ofibres is 2.5 db/m at 660nm. The fibres sustain only a single mode at least over the wavelength range from 660nm to 980nm.

  17. Inhibition of starch absorption by dietary fibre. A comparative study of wheat bran, sugar-beet fibre, and pea fibre

    DEFF Research Database (Denmark)

    Hamberg, O; Rumessen, J J; Gudmand-Høyer, E

    1989-01-01

    -20%) (p less than 0.01), and 12% (5-27%) (p less than 0.01), respectively. Bread made from 100 g of low-gluten wheat flour only escaped small-bowel absorption in three subjects with a maximal fraction of 6% (p less than 0.05). All three fibres decreased mouth-to-caecum transit time. We conclude...

  18. Inhibition of starch absorption by dietary fibre. A comparative study of wheat bran, sugar-beet fibre, and pea fibre

    DEFF Research Database (Denmark)

    Hamberg, O; Rumessen, J J; Gudmand-Høyer, E

    1989-01-01

    The effect of dietary fibre on starch absorption was investigated in 8 healthy subjects. Amounts of starch escaping small-bowel absorption was assessed by comparison of breath H2 excretion after test meals and after lactulose (10g). After ingestion of bread made from 100g of wheat flour increases...

  19. CHLORINE DIOXIDE TREATMENT OF SISAL FIBRE: SURFACE LIGNIN AND ITS INFLUENCES ON FIBRE SURFACE CHARACTERISTICS AND INTERFACIAL BEHAVIOUR OF SISAL FIBRE/PHENOLIC RESIN COMPOSITES

    Directory of Open Access Journals (Sweden)

    Linxin Zhong

    2010-11-01

    Full Text Available This paper describes an investigation of the influences of chlorine dioxide treatment on fibre surface lignin. The fibre surface characteristics and the interfacial behaviour of the sisal fibre/phenolic resin composites were also studied by SEM, AFM, and XPS. The results show that the surface of the untreated fibre contains a large amount of lignin with granular structure and non-granular structure. The surface lignin concentration is up to 51% for the untreated fibre, and then it decreases to 24% and 20% for fibres treated with 1.5 % and 2.0% chlorine dioxide, respectively. The removal of lignin from the fibre surface can enhance the interfacial strength of the composites, giving rise to increases by 36% and 28% in tensile strength and internal bonding strength. These results indicate that the surface properties of single sisal fibres can be tailored to improve the fibre/resin interface. Chlorine dioxide treatment has potential for surface modification of sisal fibre in engineering the interfacial behaviour of composites.

  20. Alginate fibres containing discrete liquid filled vacuoles for controlled delivery of healing agents in fibre reinforced composites

    NARCIS (Netherlands)

    Mookhoek, S.D.; Fischer, H.R.; Zwaag, S. van der

    2012-01-01

    The work addressed involves the preparation and application of a compartmented polymer fibre, containing multiple separated domains with liquid agent for controlled release. The created fibre is a design for improvement to the existing liquid encapsulated self-healing systems such as fibre reinforce

  1. Influence of the physical structure of flax fibres on the mechanical properties of flax fibre reinforced polypropylene composites

    NARCIS (Netherlands)

    Oever, van den M.J.A.; Bos, H.L.; Kemenade, van M.J.J.M.

    2000-01-01

    This study investigates the influence of the physical structure of flax fibres on the mechanical properties of polypropylene (PP) composites. Due to their composite-like structure, flax fibres have relatively weak lateral bonds which are in particular present in flax fibres that are often used in na

  2. Design and evaluation of carbon fibre-reinforced launch packages with segmented, copper and molybdenum fibre armatures

    NARCIS (Netherlands)

    Koops, M.; Huijser, T.; Karthaus, W.

    1997-01-01

    Fibre armatures have been studied both dynamically and statically to gain insight in their electrothermal and mechanical behaviour. In the first part of this paper, the results of launch experiments with single and multi-segment copper and molybdenum fibre armatures integrated in carbon-fibre reinfo

  3. FASEP ultra-automated analysis of fibre length distribution in glass-fibre-reinforced products

    Science.gov (United States)

    Hartwich, Mark R.; Höhn, Norbert; Mayr, Helga; Sandau, Konrad; Stengler, Ralph

    2009-06-01

    Reinforced plastic materials are widely used in high sophisticated applications. The length distribution of the fibres influences the mechanical properties of the final product. A method for automatic determination of this length distribution was developed. After separating the fibres out of the composite material without any damage, and preparing them for microscopical analysis, a mosaic of microscope pictures is taken. After image processing and analysis with mathematical methods, a complete statistic of the fibre length distribution could be determined. A correlation between fibre length distribution and mechanical properties, measured e.g. with material test methods, like tensile and impact tests, was found. This is a method to optimize the process and selection of material for the plastic parts. In result this enhances customer satisfaction and, maybe much more important, reduces costs for the manufacturer.

  4. Structural Engineering Properties of Fibre Reinforced Concrete Based On Recycled Glass Fibre Polymer (GFRP)

    OpenAIRE

    Adetiloye A; Ephraim M. E

    2015-01-01

    Glass fibre reinforced plastics (GFRP) based on resin recovered from recycling plastic waste has been shown to possess mechanical properties satisfying normative requirements. This paper investigates the flexural behavior of concrete beams reinforced with GFRP produced from resin recovered from recycled plastic wastes. A total of twelve of beams of sizes 150 ×150 ×900mm and 100 × 100 × 500mm reinforced with GFRP made from recycled glass fibre reinforced polymer was tested. The fle...

  5. Hybrid Composite Structures: Multifunctionality through Metal Fibres

    NARCIS (Netherlands)

    Ahmed, T.

    2009-01-01

    The introduction of fibre reinforced polymer composites into the wings and fuselages of the newest aircraft are changing the design and manufacturing approach. Composites provide greater freedom to designers who want to improve aircraft performance in an affordable way. In this quest, researchers ar

  6. Measuring method for optical fibre sensors

    NARCIS (Netherlands)

    Lammerink, Theodorus S.J.; Fluitman, J.H.J.

    1984-01-01

    A new measuring method for the signal amplitude in intensity modulating fibre optic sensors is described. A reference signal is generated in the time domain. The method is insensitive for the sensitivity fluctuations of the light transmitter and the light receiver. The method is experimentally

  7. Multimode supercontinuum generation in chalcogenide glass fibres

    DEFF Research Database (Denmark)

    Kubat, Irnis; Bang, Ole

    2016-01-01

    Mid-infrared supercontinuum generation is considered in chalcogenide fibres when taking into account both polarisations and the necessary higher order modes. In particular we focus on high pulse energy supercontinuum generation with long pump pulses. The modeling indicates that when only a single...

  8. Kenaf Fibre Crop for Bioeconomic Industrial Development

    NARCIS (Netherlands)

    Lips, S.J.J.; Dam, van J.E.G.

    2013-01-01

    Kenaf (Hibiscus cannabinus L.) is a high yielding fibre crop that can be utilised as raw material in many industrial applications ranging from traditional fabrics,
    yarns and ropes to new applications in building materials, composites and lightweight car parts. Kenaf competes in some applications

  9. Self-compacting fibre-reinforced concrete

    NARCIS (Netherlands)

    Grunewald, S.; Walraven, J.C.

    2001-01-01

    The project 'self-compacting fibre-reinforced concrete (SCFRC)' is part of the Dutch STW/PPM program - 'cement-bonded materials' - DCT.4010. Subproject III to which the project ,SCFRC' belongs deals with the development of new high performance concretes. The project 'SCFRC' aims at investigating the

  10. Measuring method for optical fibre sensors

    NARCIS (Netherlands)

    Lammerink, T.S.J.; Fluitman, J.H.J.

    1984-01-01

    A new measuring method for the signal amplitude in intensity modulating fibre optic sensors is described. A reference signal is generated in the time domain. The method is insensitive for the sensitivity fluctuations of the light transmitter and the light receiver. The method is experimentally teste

  11. Fibre optic communications: past, present and future

    Directory of Open Access Journals (Sweden)

    B. M. Lacquet

    2000-07-01

    Full Text Available The exponential increase in the use of the Internet and the consequent growing need for higher bandwidth demand that the telecommu­nications industry expand the laid networks at a much faster rate. Optical fibre is the only transmission medium that has the potential of unlimited bandwidth and the ability to handle very high data rates.

  12. Microscopic Study on Hemp Bast Fibre Formation

    NARCIS (Netherlands)

    Hernandez, A.; Westerhuis, W.; Dam, van J.E.G.

    2007-01-01

    Commonly, fibre hemp (Cannabis sativa) is not considered for the production of soft and easy-care textiles. However, initial tests in the textile industry have shown that certain processes allow improvement in the everyday-wear characteristics of hemp textiles. In the framework of the EU R&D pro

  13. Kenaf Fibre Crop for Bioeconomic Industrial Development

    NARCIS (Netherlands)

    Lips, S.J.J.; Dam, van J.E.G.

    2013-01-01

    Kenaf (Hibiscus cannabinus L.) is a high yielding fibre crop that can be utilised as raw material in many industrial applications ranging from traditional fabrics,
    yarns and ropes to new applications in building materials, composites and lightweight car parts. Kenaf competes in some applications

  14. Radiation curing of carbon fibre composites

    Science.gov (United States)

    Spadaro, G.; Alessi, S.; Dispenza, C.; Sabatino, M. A.; Pitarresi, G.; Tumino, D.; Przbytniak, G.

    2014-01-01

    Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric. Dynamic mechanical thermal analysis was carried out in order to determine the cross-linking degree. The analysis pointed out a nonuniformity in the cross-linking degree of the e-beam cured panels, with the formation of clusters at low Tg (glass transition temperature) and clusters at high Tg. An out-of-mould post irradiation thermal treatment on e-beam cured samples provides a higher uniformity in the network although some slight degradation effects. Mode I delamination fracture toughness and Interlaminar Shear Strength (ISS) were also investigated by means of Double Cantilever Beam (DCB) and Short Beam Shear tests, respectively. Results from this mechanical characterisation allowed to correlate fracture toughness of the bulk matrix resin, cross-linking density and fibre/matrix interaction to the delamination fracture behaviour of the fibre reinforced material.

  15. Compressive Failure of Fibre Reinforced Materials

    DEFF Research Database (Denmark)

    Jensen, Henrik Myhre

    2003-01-01

    Compressive failure of uni-directional fibre composites by the kink band mechanism is analysed taking into account effects of residual stresses. Two criteria for determining the strength of the composite material have been investigated: Kink band formation at a bifurcation stress in a composite...

  16. Ceramic fibres for high temperature insulation

    Energy Technology Data Exchange (ETDEWEB)

    Padgett, G.C.

    1986-03-01

    Traditionally, refractory linings for high temperature plant and furnaces have comprised either brick or some form of concrete. In recent years, energy conservation has encouraged the greater use of high temperature insulation which is also available in either brick or a lightweight concrete. As an alternative, insulation can also be achieved using fibrous products or fibres combining low heat transfer with low heat capacity.

  17. CERN selects Fujikura's radiation resistant fibre

    CERN Multimedia

    2007-01-01

    "Fujikura today announced that its radiation resistant single mode optical fibre has been selected by CERN, the European Laboratory for Particle Physics, to provide communication links within the world's largest particle accelerator - the Large hadron Collider (LHC) - near Genevan, Switzerland. (1/2 page)

  18. REINFORCING FIBRES AS PART OF TECHNOLOGY OF CONCRETES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-07-01

    It was identified that the basalt fibre consumption rate influences both the strength and the density of products made of cellular concrete. The length of the basalt fibre impacts the strength of products. A nomogram was developed to identify the consumption rate of the basalt fibre driven by the strength of products and the Portland cement consumption rate. The authors also studied the influence of the consumption rate of Portland cement and basalt fibre onto the structural quality ratio of the foamed fibre concrete.

  19. Fatigue damage propagation in unidirectional glass fibre reinforced composites

    DEFF Research Database (Denmark)

    Hansen, Jens Zangenberg; Alzamora Guzman, Vladimir Joel; Østergaard, R.C.

    2012-01-01

    Damage progression in unidirectional glass fibre reinforced composites exposed to tension fatigue is investigated, and a quantitative explanation is given for the observed stiffness loss. The stiffness degradation during fatigue is directly related to fibre breaks in the load-carrying axial fibre...... needs further attention and understanding in order to improve the fatigue life-time of glass fibre reinforced composites....... bundles. The underlying mechanisms are examined using digital microscopy, and it is postulated that fatigue damage initiates due to stress concentrations between the backing (transverse) layer and the unidirectional layer, followed by a cyclic fretting and axial fibre debonding. This fretting mechanism...

  20. The carbon fibre market and uses for composite wind blades

    Energy Technology Data Exchange (ETDEWEB)

    Lowe, J.R. [Tenax Fibers Gmbh and Co. KG, Wuppertal (Germany)

    1996-09-01

    Due to its excellent fatigue properties, low weight and high stiffness, carbon fibre reinforced plastic (CFRP) is the ideal material to use for the manufacture of wind blades. The present use of CFRP in the wind energy sector however is very low in comparison to glass fibre reinforced plastic (GFRP) materials. The main reason for this low use of CFRP is cost since at present times carbon fibre is valued ten times as much as glass fibre. This paper introduces carbon fibre as an alternative material to glass and examines the use of CFRP components in other high fatigue applications. (au)

  1. Nonreciprocal Coupling in Asymmetric Dual-Core Photonic Crystal Fibres

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lin; YANG Chang-Xi

    2004-01-01

    @@ The photonic crystal fibre with asymmetric dual cores is shown to attain strongly nonreciprocal coupling of the lightwave propagating along the fibre, for the first time to our knowledge. It is found that the coupling properties can be quite different when the incident position is changed. This kind of fibre could have potential for unidirectional coupler applications in fibre-optic local and metropolitan area networks. We also examine the polarization and wavelength dependence of the coupling nonreciprocity in the asymmetric dual-core photonic crystal fibres.

  2. A multi-purpose optical fibre sensor design for fibre reinforced composite materials

    Science.gov (United States)

    Fernando, G. F.; Liu, T.; Crosby, P.; Doyle, C.; Martin, A.; Brooks, D.; Ralph, B.; Badcock, R.

    1997-10-01

    This paper reports on the evaluation of a multi-functional extrinsic Fabry - Pérot optical fibre-based sensor design. The sensor was constructed using multimode and single mode optical fibres and a precision bore capillary tube. Fusion joints were used to secure the optical fibres into the capillary tube. The separation between the cleaved end-faces of the optical fibres defined the cavity length for the Fabry - Pérot sensor and the distance between the fusion joints defined the gauge length for this strain and temperature sensor. The sensor design was modified to: (i) monitor the progress of cure in an epoxy/amine resin system; (ii) detect the ingress of moisture in a cured epoxy/amine resin system; (iii) monitor the vibration characteristics of a pre- and post-impact damaged carbon fibre reinforced epoxy panel; and (iv) discriminate between strain and temperature measurements. The feasibility of using this type of sensor for cure monitoring, strain, temperature, residual stress measurements and damage detection in advanced fibre reinforced composites is demonstrated.

  3. From nanoparticles to fibres: effect of dispersion composition on fibre properties

    Energy Technology Data Exchange (ETDEWEB)

    Schirmer, Katharina S. U.; Esrafilzadeh, Dorna; Thompson, Brianna C.; Quigley, Anita F.; Kapsa, Robert M. I.; Wallace, Gordon G., E-mail: gwallace@uow.edu.au [University of Wollongong, ARC Centre for Electromaterials Science and Intelligent Polymer Research Institute (Australia)

    2015-06-15

    A polyvinyl alcohol (PVA)-stabilized polypyrrole nanodispersion has been optimised for conductivity and processability by decreasing the quantity of PVA before and after synthesis. A reduction of PVA before synthesis leads to the formation of particles with a slight increase in dry particle diameter (51 ± 6 to 63 ± 3 nm), and conversely a reduced hydrodynamic diameter. Conductivity of the dried nanoparticle films was not measureable after a reduction of PVA prior to synthesis. Using filtration of particles after synthesis, PVA content was sufficiently reduced to achieve dried thin film conductivity of 2 S cm{sup −1}, while the electroactivity of the dispersed particles remained unchanged. The as-synthesized and PVA-reduced polypyrrole particles were successfully spun into all-nanoparticle fibres using a wet-extrusion approach without the addition of any polymer or gel matrix. Using nanoparticles as a starting material is a novel approach, which allowed the production of macro-scale fibres that consisted entirely of polypyrrole nanoparticles. Fibres made from PVA-reduced polypyrrole showed higher electroactivity compared to fibres composed of the dispersion high in PVA. The mechanical properties of the fibres were also improved by reducing the amount of PVA present, resulting in a stronger, more ductile and less brittle fibre, which could find potential application in various fields.

  4. Effects of fibre orientation on mechanical properties of hybrid bamboo/glass fibre polymer composites

    Indian Academy of Sciences (India)

    B Stanly Jones Retnam; M Sivapragash; P Pradeep

    2014-08-01

    The usage of natural fibre as reinforcement in polymer composites have widely increased because of its enhanced properties. The usage of plant fibre cannot alone satisfy all the needs of the composites. Hence, introduction of hybrid plays a vital role in enhancing the mechanical properties of the FRP composites. Fibre orientation contributes significant role in improving the mechanical properties of the FRP composites. In this proposal, hybrid bamboo/glass fibre woven in different orientations such as 0°/90° and ± 45° was used and its effect on mechanical properties were studied. Composites containing hybrid fibres found to possess better mechanical properties, when compared to pure bamboo. In order to justify this, the following mechanical properties such as tensile, flexural, impact and hardness were investigated. SEM analysis shows the bonding between the matrix and reinforcement. All the above test results indicate that the introduction of natural bamboo fibre in glass reduces the overall cost of the composites with no compromise in strength and also attracted several studies covering green technologies.

  5. Biological durability and oxidative potential of man-made vitreous fibres as compared to crocidolite asbestos fibres

    Energy Technology Data Exchange (ETDEWEB)

    Hippeli, S.; Dornisch, K.; Elstner, E.F. [Lehrstuhl fuer Phytopathologie, Technische Univ. Muenchen-Weihenstephan, Freising-Weihenstephan (Germany); Wiethege, T.; Mueller, K.M. [Berufsgenossenschaftliche Kliniken Bergmannsheil, Universitaetsklinik, Inst. fuer Pathologie, Bochum (Germany); Gillissen, A. [Medizinische Universitaetsklinik und Poliklinik II, Kardiologie, Pneumologie, Bonn (Germany)

    2001-08-01

    In this study we investigated relationships between redox properties and biodurability of crocidolite asbestos fibres and three different man-made vitreous fibres (MMVF): traditional stone wool fibres (MMVF 21), glass fibres (MMVF 11) and refractory ceramic fibres (RCF). Each fibre type was incubated up to 22 weeks in four different incubation media: gamble solution (GS) pH 5.0 and pH 7.4, representing blood plasma without proteins, and surfactant-like solution (SLS) pH 5.0 and pH 7.4. During incubation time aliquots of incubation mixtures were removed and analysed in a biochemical model reaction, mimicking activated phagocytes. In addition, changes of fibre morphology and chemical composition were examined using SEM- and EDX-technology. In the presence of crocidolite asbestos fibres and MMVF 21 the formation of OH-radicals according to the Haber-Weiss sequence could be demonstrated, whereas MMVF 11 and RCF showed no reactivity. Crocidolite asbestos fibres exhibited a significant higher activity compared with the stone wool fibres at the onset of incubation. The oxidative capacities of these fibre types were shown to depend on both specific surface area and iron content. The oxidative potentials of crocidolite asbestos fibres as well as MMVF 21 were not constant during incubation over several weeks in each incubation medium. The reactivities showed sinoidal curves including reactivities much higher than those at the onset of incubation time. These irregular changes of oxidative capacity may be explained by changes of the redox state of fibre surface-complexed iron. Furthermore our results showed clear differences between incubation of fibres in GS and SLS, respectively, indicating that phospholipids play an important part in fibre dissolution behaviour and oxidative reactivity. (orig.)

  6. Mechanical properties of thermoplastic composites reinforced with Entada Mannii fibre

    Directory of Open Access Journals (Sweden)

    Oluwayomi BALOGUN

    2017-06-01

    Full Text Available The mechanical properties and fracture mechanisms of thermoplastic composites reinforced with Entada mannii fibres was investigated. Polypropylene reinforced with 1, 3, 5, and 7 wt% KOH treated and untreated Entada mannii fibres were processed using a compression moulding machine. The tensile properties, impact strength, and flexural properties of the composites were evaluated while the tensile fracture surface morphology was examined using scanning electron microscopy. The results show that reinforcing polypropylene with Entada mannii fibres resulted in improvement of the tensile strength and elastic modulus. This improvement is remarkable for 5 wt% KOH treated Entada mannii fibre reinforced composites by 28 % increase as compared with the unreinforced polypropylene. The composites reinforced with Entada mannii fibres also had impact strength values of 70 % higher than the unreinforced polypropylene. However, the polypropylene reinforced with 5 and 7wt% KOH treated fibres exhibited significantly higher flexural strength and Young’s modulus by 53% and 52% increase as compared with the unreinforced polypropylene. The fracture surface of the polypropylene composites reinforced with untreated Entada mannii fibres were characterized by fibre debonding, fibre pull-out and matrix yielding while less voids and fibre pull-outs are observed in the composites reinforced with KOH treated Entada mannii fibres. v

  7. Surface Treated Natural Fibres as Filler in Biocomposites

    Science.gov (United States)

    Schwarzova, I.; Stevulova, N.; Singovszka, E.; Terpakova, E.

    2015-11-01

    Biocomposites based on natural fibres as organic filler have been studied for several years because traditional building materials such as concrete are increasingly being replaced by advanced composite materials. Natural fibres are a potential replacement of glass fibres in composite materials. Inherent advantages such as low density, biodegradability and comparable specific mechanical properties make natural fibres an attractive option. However, limitations such as poor thermal stability, moisture absorption and poor compatibility with matrix are challenges that need to be resolved. The primary objective of this research was to study the effect of surface treatment on properties of hemp hurds like a natural lignocellulosic material and composites made thereof. Industrial hemp fibre is the one of the most suitable fibres for use in composite materials because of its good specific properties, as well as it being biologically degradable and CO2 neutral. Improving interfacial bonding between fibres and matrix is an important factor in using hemp fibres as reinforcement in composites. In order to improve interfacial bonding, modifications can be made to the hemp fibres to remove non- cellulosic compounds, separate hemp fibres from their bundles, and modify the fibre surface. This paper contains the comparison of FTIR spectra caused by combination of physical and chemical treatment of hemp material with unmodified sample. Modification of hemp hurds was carried out by NaOH solution and by ultrasonic treatment (deionized water and NaOH solution were used as the cleaning mediums).

  8. Exposure to ceramic man-made mineral fibres.

    Science.gov (United States)

    Friar, J J; Phillips, A M

    1989-01-01

    Ceramic fibres (also known as refractory fibres) are regarded here as man-made mineral fibres (MMMF) capable of withstanding temperatures of 1000-1600 degrees C without appreciable distortion or softening. Ceramic fibres are manufactured largely from the aluminosilicate group of minerals but some contain only alumina, zirconia or silica. Simultaneous personal gravimetric and optical fibre count samples were taken throughout the industry. It has not been possible to correlate gravimetric results with fibre counts in any meaningful way. The general conclusions are as follows: (a) gravimetrically, exposures ranged from less than 1 mg/m3 for light tasks to over 10 mg/m3 for some insulation workers. Exposures above 10 mg/m3 were not necessarily associated with correspondingly high fibre counts; (b) fibre counts rarely exceeded 1 f/ml, and it appears that ceramic fibre materials, in company with other MMMF, do not readily produce high airborne fibre counts; (c) control of dust from mineral wools to 5 mg/m3 achieves control to below 1 f/ml. This relationship does not hold for superfine MMMF and does not always hold for ceramic fibres.

  9. Investigation of digital light processing using fibre-reinforced polymers

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Nielsen, Jakob Skov

    2016-01-01

    of fibre length and shape compared to layer thickness has been investigated including concepts to circumvent clustering of the fibres.This research contributes to the implementation of fibre-reinforced polymers in additive manufacturing technologies. Digital light processing allows generation...... of miniaturized objects with relatively high surface quality compared to other additive manufacturing technologies. This paper aim to move fibre reinforced resin parts one step closer towards mechanically strong production-quality components.......-reinforced polymers in digital light processing (DLP) are limited. Fibre-reinforced polymer composites were manufactured into test objects using digital light processing. Short fibres were used in an unordered manner. An anisotropic property due to fibre orientation within the material was observed. The importance...

  10. Natural Composites: Cellulose Fibres and the related Performance of Composites

    DEFF Research Database (Denmark)

    Lilholt, Hans; Madsen, Bo

    2014-01-01

    Biobased materials are becoming of increasing interest as potential structural materials for the future. A useful concept in this context is the fibre reinforcement of materials by stiff and strong fibres. The biobased resources can contribute with cellulose fibres and biopolymers. This offers...... the potential for stiff and strong biocomposite materials, but these have some limitations and obstacles to full performance. The focus will be on the ultra-structure, and the strength and stiffness of cellulose fibres, on the (unavoidable) defects causing large reductions in strength and moderate reductions...... in stiffness, on the packing ability of cellulose fibres and the related maximum fibre volume fraction in composites, on the moisture sorption of cellulose fibres and the related mass increase and (large) hygral strains induced, and on the mechanical performance of composites....

  11. Investigation of digital light processing using fibre-reinforced polymers

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Nielsen, Jakob Skov

    2016-01-01

    of fibre length and shape compared to layer thickness has been investigated including concepts to circumvent clustering of the fibres.This research contributes to the implementation of fibre-reinforced polymers in additive manufacturing technologies. Digital light processing allows generation...... of miniaturized objects with relatively high surface quality compared to other additive manufacturing technologies. This paper aim to move fibre reinforced resin parts one step closer towards mechanically strong production-quality components.......-reinforced polymers in digital light processing (DLP) are limited. Fibre-reinforced polymer composites were manufactured into test objects using digital light processing. Short fibres were used in an unordered manner. An anisotropic property due to fibre orientation within the material was observed. The importance...

  12. Mechanical Properties of Man-Made Mineral glass fibres

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    ; man-made mineral glass fibres. The basaltic melt is prevented from crystallizing due to the high cooling rate, forming the mineral glass wool fibres. Basaltic mineral wool fibres are of high interest in industry due to their good chemical durability and excellent heat and sound insulation properties...... and hence they are used for insulation products. In spite of those advantages, man made mineral wool fibres still show a certain degree of brittleness, which limits the further improvement of man made mineral wool fibres for both transportation and application. Therefore, a reduction in the brittleness...... of man made mineral wool fibres, and an improvement of the mechanical performances of man made mineral wool fibres are an evitable task for us. To do so, it is important to look into the fracture behaviour and its connection to the mechanical strength. In order to improve the understanding...

  13. Compaction in optical fibres and fibre Bragg gratings under nuclear reactor high neutron and gamma fluence

    Energy Technology Data Exchange (ETDEWEB)

    Remy, L.; Cheymol, G. [CEA, French Nuclear Energy Commission, Nuclear Energy Division, DPC/SEARS/LISL Bat 467 CEA Saclay 91191 Gif/Yvette Cedex (France); Gusarov, A. [SCK.CEN - Belgian Nuclear Research center, Boeretang 200 2400 Mol (Belgium); Morana, A.; Marin, E.; Girard, S. [Universite de Saint-Etienne, Laboratoire Hubert Curien, UMR CNRS5516, 18, rue du Pr. Lauras, F-42000 Saint-Etienne (France)

    2015-07-01

    In the framework of the development by CEA and SCK.CEN of a Fabry Perot Sensor (FPS) able to measure dimensional changes in Material Testing Reactor (MTR), the first goal of the SAKE 1 (Smirnof extention - Additional Key-tests on Elongation of glass fibres) irradiation was to measure the linear compaction of single mode fibres under high fast neutron fluence. Indeed, the compaction of the fibre which forms one side of the Fabry Perot cavity, may in particular cause a noticeable measurement error. An accurate quantification of this effect is then required to predict the radiation-induced drift and optimize the sensor design. To achieve this, an innovative approach was used. Approximately seventy uncoated fibre tips (length: 30 to 50 mm) have been prepared from several different fibre samples and were installed in the SCK.CEN BR2 reactor (Mol Belgium). After 22 days of irradiation a total fast (E > 1 MeV) fluence of 3 to 5x10{sup 19} n{sub fast}/cm{sup 2}, depending on the sample location, was accumulated. The temperature during irradiation was 291 deg. C, which is not far from the condition of the intended FPS use. A precise measurement of each fibre tip length was made before the irradiation and compared to the post irradiation measurement highlighting a decrease of the fibres' length corresponding to about 0.25% of linear compaction. The amplitude of the changes is independent of the capsule, which could mean that the compaction effect saturates even at the lowest considered fluence. In the prospect of performing distributed temperature measurement in MTR, several fibre Bragg gratings written using a femtosecond laser have been also irradiated. All the gratings were written in radiation hardened fibres, and underwent an additional treatment with a procedure enhancing their resistance to ionizing radiations. A special mounting made it possible to test the reflection and the transmission of the gratings on fibre samples cut down to 30 to 50 mm. The comparison

  14. Dual color x-rays from Thomson or Compton sources

    Science.gov (United States)

    Petrillo, V.; Bacci, A.; Curatolo, C.; Ferrario, M.; Maroli, C.; Rau, J. V.; Ronsivalle, C.; Serafini, L.; Vaccarezza, C.; Venturelli, M.

    2015-05-01

    We analyze the possibility of producing two color X or γ radiation by Thomson/Compton back-scattering between a high intensity laser pulse and a two-energy level electron beam, constituted by a couple of beamlets separated in time and/or energy obtained by a photoinjector with comb laser techniques and linac velocity bunching. The parameters of the Thomson source at SPARC_LAB have been simulated, proposing a set of values for a realistic experiments.

  15. Dual color x rays from Thomson or Compton sources

    Science.gov (United States)

    Petrillo, V.; Bacci, A.; Curatolo, C.; Ferrario, M.; Gatti, G.; Maroli, C.; Rau, J. V.; Ronsivalle, C.; Serafini, L.; Vaccarezza, C.; Venturelli, M.

    2014-02-01

    We analyze the possibility of producing two-color x or γ radiation by Thomson/Compton backscattering between a high intensity laser pulse and a two-energy level electron beam, constituted by a couple of beamlets separated in time and/or energy obtained by a photoinjector with comb laser techniques and linac velocity bunching. The parameters of the Thomson source at SPARC_LAB have been simulated, proposing a set of realistic experiments.

  16. Comparison of traditional field retting and Phlebia radiata Cel 26 retting of hemp fibres for fibre-reinforced composites.

    Science.gov (United States)

    Liu, Ming; Ale, Marcel T; Kołaczkowski, Bartłomiej; Fernando, Dinesh; Daniel, Geoffrey; Meyer, Anne S; Thygesen, Anders

    2017-12-01

    Classical field retting and controlled fungal retting of hemp using Phlebia radiata Cel 26 (a mutant with low cellulose degrading ability) were compared with pure pectinase treatment with regard to mechanical properties of the produced fibre/epoxy composites. For field retting a classification of the microbial evolution (by gene sequencing) and enzyme profiles were conducted. By phylogenetic frequency mapping, different types of fungi, many belonging to the Ascomycota phylum were found on the fibres during the first 2 weeks of field retting, and thereafter, different types of bacteria, notably Proteobacteria, also proliferated on the field retted fibres. Extracts from field retted fibres exhibited high glucanase activities, while extracts from P. radiata Cel 26 retted fibres showed high polygalacturonase and laccase activities. As a result, fungal retting gave a significantly higher glucan content in the fibres than field retting (77 vs. 67%) and caused a higher removal of pectin as indicated by lower galacturonan content of fibres (1.6%) after fibres were retted for 20 days with P. radiata Cel 26 compared to a galacturonan content of 3.6% for field retted fibres. Effective fibre stiffness increased slightly after retting with P. radiata Cel 26 from 65 to 67 GPa, while it decreased after field retting to 52 GPa. Effective fibre strength could not be determined similarly due to variations in fibre fracture strain and fibre-matrix adhesion. A maximum composite strength with 50 vol% fibres of 307 MPa was obtained using P. radiata Cel 26 compared to 248 MPa with field retting.

  17. Biological durability and oxidative potential of man-made vitreous fibres as compared to crocidolite asbestos fibres.

    Science.gov (United States)

    Hippeli, S; Dornisch, K; Wiethege, T; Gillissen, A; Müller, K M; Elstner, E F

    2001-01-01

    In this study we investigated relationships between redox properties and biodurability of crocidolite asbestos fibres and three different man-made vitreous fibres (MMVF): traditional stone wool fibres (MMVF 21), glass fibres (MMVF 11) and refractory ceramic fibres (RCF). Each fibre type was incubated up to 22 weeks in four different incubation media: gamble solution (GS) pH 5.0 and pH 7.4, representing blood plasma without proteins, and surfactant-like solution (SLS) pH 5.0 and pH 7.4. During incubation time aliquots of incubation mixtures were removed and analysed in a biochemical model reaction, mimicking activated phagocytes. In addition, changes of fibre morphology and chemical composition were examined using SEM- and EDX-technology. In the presence of crocidolite asbestos fibres and MMVF 21 the formation of OH*-radicals according to the Haber-Weiss sequence could be demonstrated, whereas MMVF 11 and RCF showed no reactivity. Crocidolite asbestos fibres exhibited a significant higher activity compared with the stone wool fibres at the onset of incubation. The oxidative capacities of these fibre types were shown to depend on both specific surface area and iron content. The oxidative potentials of crocidolite asbestos fibres as well as MMVF 21 were not constant during incubation over several weeks in each incubation medium. The reactivities showed sinoidal curves including reactivities much higher than those at the onset of incubation time. These irregular changes of oxidative capacity may be explained by changes of the redox state of fibre surface-complexed iron. Furthermore our results showed clear differences between incubation of fibres in GS and SLS, respectively, indicating that phospholipids play an important part in fibre dissolution behaviour and oxidative reactivity. In conclusion we suggest, that biodurability testing procedures should not exclusively concentrate on dissolution rates of fibres. They should include fibre characteristics concerning known

  18. Acoustical model of a Shoddy fibre absorber

    Science.gov (United States)

    Manning, John Peter

    Shoddy fibres or "Shoddies" are a mixture of post-consumer and post-industrial fibres diverted from textile waste streams and recycled into their raw fibre form. They have found widespread use as a raw material for manufacturing sound absorbers that include, but are not limited to: automotive, architectural and home appliance applications. The purpose of this project is to develop a simple acoustic model to describe the acoustic behaviour of sound absorbers composed primarily of Shoddy fibres. The model requires knowledge of the material's bulk density only. To date, these materials have not been the focus of much published research and acoustical designers must rely on models that were developed for other materials or are overly complex. For modelling purposes, an equivalent fluid approach is chosen to balance complexity and accuracy. In deriving the proposed model, several popular equivalent fluid models are selected and the required input parameters for each model identified. The models are: the model of Delaney and Bazley, two models by Miki, the model of Johnson in conjunction with the model of Champoux and Allard and the model of Johnson in conjunction with the model of Lafarge. Characterization testing is carried out on sets of Shoddy absorbers produced using three different manufacturing methods. The measured properties are open porosity, tortuosity, airflow resistivity, the viscous and thermal characteristic lengths and the static thermal permeability. Empirical relationships between model parameters and bulk density are then derived and used to populate the selected models. This yields several 'simplified' models with bulk density as the only parameter. The most accurate model is then selected by comparing each model's prediction to the results of normal incidence sound absorption tests. The model of Johnson-Lafarge populated with the empirical relations is the most accurate model over the range of frequencies considered (approx. 300 Hz - 4000 Hz

  19. Effect of discrete fibre reinforcement on soil tensile strength

    Directory of Open Access Journals (Sweden)

    Jian Li

    2014-04-01

    Full Text Available The tensile behaviour of soil plays a significantly important role in various engineering applications. Compacted soils used in geotechnical constructions such as dams and clayey liners in waste containment facilities can suffer from cracking due to tensile failure. In order to increase soil tensile strength, discrete fibre reinforcement technique was proposed. An innovative tensile apparatus was developed to determine the tensile strength characteristics of fibre reinforced soil. The effects of fibre content, dry density and water content on the tensile strength were studied. The results indicate that the developed test apparatus was applicable in determining tensile strength of soils. Fibre inclusion can significantly increase soil tensile strength and soil tensile failure ductility. The tensile strength basically increases with increasing fibre content. As the fibre content increases from 0% to 0.2%, the tensile strength increases by 65.7%. The tensile strength of fibre reinforced soil increases with increasing dry density and decreases with decreasing water content. For instance, the tensile strength at a dry density of 1.7 Mg/m3 is 2.8 times higher than that at 1.4 Mg/m3. It decreases by 30% as the water content increases from 14.5% to 20.5%. Furthermore, it is observed that the tensile strength of fibre reinforced soil is dominated by fibre pull-out resistance, depending on the interfacial mechanical interaction between fibre surface and soil matrix.

  20. Mechanical properties of natural fibre reinforced polymer composites

    Indian Academy of Sciences (India)

    A S Singha; Vijay Kumar Thakur

    2008-10-01

    During the last few years, natural fibres have received much more attention than ever before from the research community all over the world. These natural fibres offer a number of advantages over traditional synthetic fibres. In the present communication, a study on the synthesis and mechanical properties of new series of green composites involving Hibiscus sabdariffa fibre as a reinforcing material in urea–formaldehyde (UF) resin based polymer matrix has been reported. Static mechanical properties of randomly oriented intimately mixed Hibiscus sabdariffa fibre reinforced polymer composites such as tensile, compressive and wear properties were investigated as a function of fibre loading. Initially urea–formaldehyde resin prepared was subjected to evaluation of its optimum mechanical properties. Then reinforcing of the resin with Hibiscus sabdariffa fibre was accomplished in three different forms: particle size, short fibre and long fibre by employing optimized resin. Present work reveals that mechanical properties such as tensile strength, compressive strength and wear resistance etc of the urea–formaldehyde resin increases to considerable extent when reinforced with the fibre. Thermal (TGA/DTA/DTG) and morphological studies (SEM) of the resin and biocomposites have also been carried out.

  1. Effect of discrete fibre reinforcement on soil tensile strength

    Institute of Scientific and Technical Information of China (English)

    Jian Li; Chaosheng Tang; Deying Wang; Xiangjun Pei; Bin Shi

    2014-01-01

    The tensile behaviour of soil plays a significantly important role in various engineering applications. Compacted soils used in geotechnical constructions such as dams and clayey liners in waste containment facilities can suffer from cracking due to tensile failure. In order to increase soil tensile strength, discrete fibre reinforcement technique was proposed. An innovative tensile apparatus was developed to deter-mine the tensile strength characteristics of fibre reinforced soil. The effects of fibre content, dry density and water content on the tensile strength were studied. The results indicate that the developed test apparatus was applicable in determining tensile strength of soils. Fibre inclusion can significantly in-crease soil tensile strength and soil tensile failure ductility. The tensile strength basically increases with increasing fibre content. As the fibre content increases from 0%to 0.2%, the tensile strength increases by 65.7%. The tensile strength of fibre reinforced soil increases with increasing dry density and decreases with decreasing water content. For instance, the tensile strength at a dry density of 1.7 Mg/m3 is 2.8 times higher than that at 1.4 Mg/m3. It decreases by 30% as the water content increases from 14.5% to 20.5%. Furthermore, it is observed that the tensile strength of fibre reinforced soil is dominated by fibre pull-out resistance, depending on the interfacial mechanical interaction between fibre surface and soil matrix.

  2. Applicability of the Waste Fibres in Cement Paste

    Directory of Open Access Journals (Sweden)

    Regina KALPOKAITĖ DIČKUVIENĖ

    2013-09-01

    Full Text Available Fibres produced from waste catalyst together with commercially available polypropylene fibres were incorporated into ordinary Portland cement paste. The effects of fibre content as well as a mix of different type of fibres on mechanical and physical properties of wet and dry samples were investigated. The results showed that presence of fibres reduced compressive strength of the plain cement in wet and dry state. Contrary, when the combination of 1.5 wt% waste and 1.5 wt% polypropylene fibres was used flexural strength of cement mixture increased by up to 9 % at the age of 28 days. It was observed that addition of 1.5 wt% of only waste fibres improved flexural strength after long hydration period as well. However, the lowest mechanical strength results showed samples with 3 wt% of waste fibres. It was also observed that higher content of waste fibres reduced porosity of the cement mixture and consequently, decreased water absorption capacity. Presence of fibres reduced drying shrinkage of samples and they were lower than plain cement after 28 days of hydration. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.1992

  3. Strength and toughness of structural fibres for composite material reinforcement.

    Science.gov (United States)

    Herráez, M; Fernández, A; Lopes, C S; González, C

    2016-07-13

    The characterization of the strength and fracture toughness of three common structural fibres, E-glass, AS4 carbon and Kevlar KM2, is presented in this work. The notched specimens were prepared by means of selective carving of individual fibres by means of the focused ion beam. A straight-fronted edge notch was introduced in a plane perpendicular to the fibre axis, with the relative notch depth being a0/D≈0.1 and the notch radius at the tip approximately 50 nm. The selection of the appropriate beam current during milling operations was performed to avoid to as much as possible any microstructural changes owing to ion impingement. Both notched and un-notched fibres were submitted to uniaxial tensile tests up to failure. The strength of the un-notched fibres was characterized in terms of the Weibull statistics, whereas the residual strength of the notched fibres was used to determine their apparent toughness. To this end, the stress intensity factor of a fronted edge crack was computed by means of the finite-element method for different crack lengths. The experimental results agreed with those reported in the literature for polyacrylonitrile-based carbon fibres obtained by using similar techniques. After mechanical testing, the fracture surface of the fibres was analysed to ascertain the failure mechanisms. It was found that AS4 carbon and E-glass fibres presented the lower toughness with fracture surfaces perpendicular to the fibre axis, emanating from the notch tip. The fractured region of Kevlar KM2 fibres extended along the fibre and showed large permanent deformation, which explains their higher degree of toughness when compared with carbon and glass fibres. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'.

  4. Comparison of cytotoxicity of man-made vitreous fibres.

    Science.gov (United States)

    Luoto, K; Holopainen, M; Sarataho, M; Savolainen, K

    1997-01-01

    The purpose of the study was to compare the cytotoxicity of man-made vitreous fibres (MMVFs): four refractory ceramic fibres (RCFs 1-4), two glasswool fibres (MMVF 10 and 11), a rockwool fibre (MMVF 21) and a slagwool fibre (MMVF 22). The ability of the fibres to induce haemolysis in sheep erythrocytes, to release lactate dehydrogenase (LDH) from rat alveolar macrophages (AM) and to increase the production of reactive oxygen metabolites (ROMs) in human polymorphonuclear leukocytes (PML) was studied. To assess the relative cytotoxicity of MMVFs, their toxicity was compared with that induced by quartz, chrysotile or titanium dioxide. MMVFs induced a modest, but dose-dependent, increase of haemolysis at doses of 0.5, 2.5 and 5.0 mg ml-1. The amount of haemolysis and LDH release induced by MMVFs was generally similar to that induced by titanium dioxide. Glasswool fibre MMVF 10 induced less LDH release from rat AM than rockwool MMVF 21 or slagwool MMVF 22 fibres, whereas glasswool fibre MMVF 11 induced less LDH release than slagwool fibre MMVF 22 (P < 0.05). All fibres also dose-dependently increased the production of ROMs at doses between 25 and 500 micrograms ml-1. The shapes of the time-courses of MMVF-induced production of ROMs suggest that the mechanisms whereby the different fibres induce ROM production may exhibit similar features. There are clear-cut differences in the potency of various MMVFs to induce cytotoxicity and oxidative burst. The present results also emphasize the importance of using several measures of toxicity when assessing the biological activity of various fibres in vitro.

  5. LHCb Scintillating Fibre Tracker Engineering Design Review Report: Fibres, Mats and Modules

    CERN Document Server

    Joram, Christian; Leverington, Blake Dean; Kirn, Thomas; Bachmann, Sebastian; Ekelhof, Robert Jan; Müller, Janine

    2015-01-01

    During the Long Shutdown 2 of the LHC, the LHCb collaboration will replace the current Outer and Inner Tracker by a single tracking detector, based on 2.42m long scintillating fibres with a diameter of 250 $\\mu$m, readout by silicon photo-multipliers (SiPM). The fibers are arranged in mats of 6 fibre-layers with a width of 130.65 mm. Eight fibre mats will form a module and are sandwiched between honeycomb and carbon fibre composite panels to provide stability and support over the module length of 4.85m. At either end of the module are the interfaces to the SiPMs and the front-end electronics. The active detection area of the Scintillating Fiber Tracker (SciFi) of 360m$^2$ will comprise 144 single modules arranged in 12 detection planes. This document summarizes the engineering design of the fibre mats and of the modules including the interfaces to the SiPMs and the mounting to the detector frames. Mechanical and detector properties of several prototype modules are discussed. The production procedure of the fi...

  6. A viscoelastic-viscoplastic model for short-fibre reinforced polymers with complex fibre orientations

    Directory of Open Access Journals (Sweden)

    Nciri M.

    2015-01-01

    Full Text Available This paper presents an innovative approach for the modelling of viscous behaviour of short-fibre reinforced composites (SFRC with complex distributions of fibre orientations and for a wide range of strain rates. As an alternative to more complex homogenisation methods, the model is based on an additive decomposition of the state potential for the computation of composite’s macroscopic behaviour. Thus, the composite material is seen as the assembly of a matrix medium and several linear elastic fibre media. The division of short fibres into several families means that complex distributions of orientation or random orientation can be easily modelled. The matrix behaviour is strain-rate sensitive, i.e. viscoelastic and/or viscoplastic. Viscoelastic constitutive laws are based on a generalised linear Maxwell model and the modelling of the viscoplasticity is based on an overstress approach. The model is tested for the case of a polypropylene reinforced with short-glass fibres with distributed orientations and subjected to uniaxial tensile tests, in different loading directions and under different strain rates. Results demonstrate the efficiency of the model over a wide range of strain rates.

  7. Presynaptic calcium signalling in cerebellar mossy fibres

    DEFF Research Database (Denmark)

    Thomsen, Louiza Bohn; Jörntell, Henrik; Midtgaard, Jens

    2010-01-01

    Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A tetrodotoxin (TTX....... Calcium imaging using Calcium-Green dextran revealed a stimulus-evoked all-or-none TTX-sensitive calcium signal in simple and complex rosettes. All compartments of a complex rosette were activated during electrical activation of the mossy fibre, while individual simple and complex rosettes along an axon......)-sensitive fast Na(+) spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers...

  8. Fibre Optic Sensors for Selected Wastewater Characteristics

    Directory of Open Access Journals (Sweden)

    Sulaiman W. Harun

    2013-07-01

    Full Text Available Demand for online and real-time measurements techniques to meet environmental regulation and treatment compliance are increasing. However the conventional techniques, which involve scheduled sampling and chemical analysis can be expensive and time consuming. Therefore cheaper and faster alternatives to monitor wastewater characteristics are required as alternatives to conventional methods. This paper reviews existing conventional techniques and optical and fibre optic sensors to determine selected wastewater characteristics which are colour, Chemical Oxygen Demand (COD and Biological Oxygen Demand (BOD. The review confirms that with appropriate configuration, calibration and fibre features the parameters can be determined with accuracy comparable to conventional method. With more research in this area, the potential for using FOS for online and real-time measurement of more wastewater parameters for various types of industrial effluent are promising.

  9. Optical Fibre Dosimeter for SASE FEL Undulators

    CERN Document Server

    Körfer, M

    2003-01-01

    Single pass Free Electron Lasers (FELs) based on self-amplified spontaneous emission (SASE) are developed for high brightness and short wavelength applications. They use permanent magnet undulators which are radiation sensitive devices. During accelerator commissioning beam losses can appear anywhere along the undulator line. To avoid damage of the permanent magnets due to radiation, an optical fibre dosimeter system can be used. The increase of absorption caused by ionizing radiation is measured in radiation sensitive optical fibers. The dose system enables relatively fast particle loss tuning during accelerator operation and allows the monitoring of the accumulated dose. Dose measurements in narrow gaps which are inaccessible for any other (online) dosimeter type become possible. The electromagnetic insensitivity of optical fibre sensor is an advantage of applications in strong magnetic undulator fields. At each location the light absorption is measured by using an optical power-meter. The dynamic range is ...

  10. Global Embedding of Fibre Inflation Models

    CERN Document Server

    Cicoli, Michele; Shukla, Pramod

    2016-01-01

    We present concrete embeddings of fibre inflation models in globally consistent type IIB Calabi-Yau orientifolds with closed string moduli stabilisation. After performing a systematic search through the existing list of toric Calabi-Yau manifolds, we find several examples that reproduce the minimal setup to embed fibre inflation models. This involves Calabi-Yau manifolds with $h^{1,1}= 3$ which are K3 fibrations over a $\\mbb{P}^1$ base with an additional shrinkable rigid divisor. We then provide different consistent choices of the underlying brane set-up which generate a non-perturbative superpotential suitable for moduli stabilisation and string loop corrections with the correct form to drive inflation. For each Calabi-Yau orientifold setting, we also compute the effect of higher derivative contributions and study their influence on the inflationary dynamics.

  11. Single-Mode Soft Glass Fibres

    Science.gov (United States)

    Jedrzejewski, Kazimierz

    1990-01-01

    The technology of single-mode optical soft glass fibres is developed. The well-known rod in tube technique with multiple sleeving was taken to achieve proper dimensions. The ultrasonic mill-drill was used to prepare different structures: high ▵ , high birefringent, D-shaped, multicore, metal wire/glass compound and doped. The temperature processes were carried out very carefully to avoid glass decomposition. The geometry, refractive index profiles, mode near field patterns and λc agreed with the predicted and material data. The losses were reasonably low, better then 370 dB/km (800 nm). The enhanced Verdet constants and nonlinear coefficients values, high dopants levels and other special properties including low process temperatures are very attractive for fibre short range applications, sensors and devices e.g. polarizers, couplers, lasers, filters.

  12. Creep Strength of Discontinuous Fibre Composites

    DEFF Research Database (Denmark)

    Pedersen, Ole Bøcker

    1974-01-01

    relation between stress and strain rate. Expressions for the interface stress, the creep velocity profile adjacent to the fibres and the creep strength of the composite are derived. Previous results for the creep strength, sc = aVfs0 ( \\frac[( Î )\\dot] [( Î )\\dot] 0 )1/nr1 + 1/n c=Vf001n1+1n in which[( Î...... )\\dot] is the composite creep rate,V f is the fibre volume fraction,sgr 0,epsi 0 andn are the constants in the matrix creep law. The creep strength coefficient agr is found to be very weakly dependent onV f and practically independent ofn whenn is greater than about 6....

  13. Retention of Cationic Starch onto Cellulose Fibres

    Science.gov (United States)

    Missaoui, Mohamed; Mauret, Evelyne; Belgacem, Mohamed Naceur

    2008-08-01

    Three methods of cationic starch titration were used to quantify its retention on cellulose fibres, namely: (i) the complexation of CS with iodine and measurement of the absorbency of the ensuing blue solution by UV-vis spectroscopy; (ii) hydrolysis of the starch macromolecules followed by the conversion of the resulting sugars to furan-based molecules and quantifying the ensuing mixture by measuring their absorbance at a Ι of 490 nm, using the same technique as previous one and; finally (iii) hydrolysis of starch macromolecules by trifluoro-acetic acid and quantification of the sugars in the resulting hydrolysates by high performance liquid chromatography. The three methods were found to give similar results within the range of CS addition from 0 to 50 mg per g of cellulose fibres.

  14. Fibre optic sensors for selected wastewater characteristics.

    Science.gov (United States)

    Chong, Su Sin; Aziz, A R Abdul; Harun, Sulaiman W

    2013-07-05

    Demand for online and real-time measurements techniques to meet environmental regulation and treatment compliance are increasing. However the conventional techniques, which involve scheduled sampling and chemical analysis can be expensive and time consuming. Therefore cheaper and faster alternatives to monitor wastewater characteristics are required as alternatives to conventional methods. This paper reviews existing conventional techniques and optical and fibre optic sensors to determine selected wastewater characteristics which are colour, Chemical Oxygen Demand (COD) and Biological Oxygen Demand (BOD). The review confirms that with appropriate configuration, calibration and fibre features the parameters can be determined with accuracy comparable to conventional method. With more research in this area, the potential for using FOS for online and real-time measurement of more wastewater parameters for various types of industrial effluent are promising.

  15. 2D Saturable Absorbers for Fibre Lasers

    Directory of Open Access Journals (Sweden)

    Robert I. Woodward

    2015-11-01

    Full Text Available Two-dimensional (2D nanomaterials are an emergent and promising platform for future photonic and optoelectronic applications. Here, we review recent progress demonstrating the application of 2D nanomaterials as versatile, wideband saturable absorbers for Q-switching and mode-locking fibre lasers. We focus specifically on the family of few-layer transition metal dichalcogenides, including MoS2, MoSe2 and WS2.

  16. Elastic fibres and vascular structure in hypertension.

    Science.gov (United States)

    Arribas, Silvia M; Hinek, Aleksander; González, M Carmen

    2006-09-01

    Blood vessels are dynamic structures composed of cells and extracellular matrix (ECM), which are in continuous cross-talk with each other. Thus, cellular changes in phenotype or in proliferation/death rate affect ECM synthesis. In turn, ECM elements not only provide the structural framework for vascular cells, but they also modulate cellular function through specific receptors. These ECM-cell interactions, together with neurotransmitters, hormones and the mechanical forces imposed by the heart, modulate the structural organization of the vascular wall. It is not surprising that pathological states related to alterations in the nervous, humoral or haemodynamic environment-such as hypertension-are associated with vascular wall remodeling, which, in the end, is deleterious for cardiovascular function. However, the question remains whether these structural alterations are simply a consequence of the disease or if there are early cellular or ECM alterations-determined either genetically or by environmental factors-that can predispose to vascular remodeling independent of hypertension. Elastic fibres might be key elements in the pathophysiology of hypertensive vascular remodeling. In addition to the well known effects of hypertension on elastic fibre fatigue and accelerated degradation, leading to loss of arterial wall resilience, recent investigations have highlighted new roles for individual components of elastic fibres and their degradation products. These elements can act as signal transducers and regulate cellular proliferation, migration, phenotype, and ECM degradation. In this paper, we review current knowledge regarding components of elastic fibres and discuss their possible pathomechanistic associations with vascular structural abnormalities and with hypertension development or progression.

  17. Fabrication of Polymer Optical Fibre (POF Gratings

    Directory of Open Access Journals (Sweden)

    Yanhua Luo

    2017-03-01

    Full Text Available Gratings inscribed in polymer optical fibre (POF have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

  18. Fibre suspension flocculation under simulated forming conditions

    OpenAIRE

    Yan, Huawei

    2004-01-01

    A flow loop system for study of fibre flocculation insuspensions has been developed. The system is designed tosimulate the flow conditions in a paper machine headbox. It isequipped with a radial distributor feeding a step diffuser pipepackage, after which the flow is contracted in a 2-D nozzle.The flow system is also equipped with a secondary flowcontraction with an area reduction ratio of 2:1 after theheadbox nozzle, mimicking accelerations that may take placeduring forming. The flow system ...

  19. Co-extrusion of piezoelectric ceramic fibres

    OpenAIRE

    Ismael Michen, Marina

    2011-01-01

    The present work successfully developed a methodology for fabricating lead zirconate titanate [PZT] thin solid- and hollow-fibres by the thermoplastic co-extrusion process. The whole process chain, that includes: a) compounding, involving the mixing of ceramic powder with a thermoplastic binder, b) rheological characterizations, c) preform composite fabrication followed by co-extrusion, d) debinding and, finally, e) sintering of the body to near full density, is systematical...

  20. Fibre optic sensors for mine hazard detection

    Energy Technology Data Exchange (ETDEWEB)

    Liu, T; Wang, C; Wei, Y; Zhao, Y; Shang, Y; Wang, Z [Laser Institute of Shandong Academy of Science (China); Huo, D [Shandong Micro-Sensor Photonics Limited, 19 Keyuan Road, Jinan, Shandong province, 250014 (China); Ning, Y, E-mail: tongyuliu@hotmail.co [Intelligent Sensor Systems Limited, Rockley Manor, Rockley, Wiltshire (United Kingdom)

    2009-07-01

    We report the development of a comprehensive safety monitoring solution for coal mines. A number of fibre optic sensors have been developed and deployed for safety monitoring of mine roof integrity and hazardous gases. The FOS-based mine hazard detection system offers unique advantages of intrinsic safety, multi-location and multi-parameter monitoring. They can be potentially used to build expert systems for mine hazard early detection and prevention.

  1. Spider's web inspires fibres for industry

    Science.gov (United States)

    Dacey, James

    2010-03-01

    Spiders may not be everybody's idea of natural beauty, but nobody can deny the artistry in the webs that they spin, especially when decorated with water baubles in the morning dew. Inspired by this spectacle, a group of researchers in China has mimicked the structural properties of the spider's web to create a fibre for industry that can manipulate water with the same skill and efficiency, writes James Dacey.

  2. Applications for fibre-reinforced plastic

    Energy Technology Data Exchange (ETDEWEB)

    Teuschler, V. [Fiberdur-Vanck (Germany)

    1999-07-01

    The outstanding mechanical properties of fibre-reinforced plastic are extolled. It has strength comparable with that of steel, and other physical properties that give it advantages over ferrous materials for use in pipelines, shipbuilding and offshore conduits. It has well established uses in aircraft, automobiles and boats and is probably more resistant to weathering and corrosion than any other material. The electricity-conducting Navicon pipe, the Fiberdur-vinyl ester/epoxy system and the Fiberdur-DOS system are described.

  3. Fibre suspension flocculation under simulated forming conditions

    OpenAIRE

    Yan, Huawei

    2004-01-01

    A flow loop system for study of fibre flocculation insuspensions has been developed. The system is designed tosimulate the flow conditions in a paper machine headbox. It isequipped with a radial distributor feeding a step diffuser pipepackage, after which the flow is contracted in a 2-D nozzle.The flow system is also equipped with a secondary flowcontraction with an area reduction ratio of 2:1 after theheadbox nozzle, mimicking accelerations that may take placeduring forming. The flow system ...

  4. PROFITABILITY OF INCREMENTAL EXPENDITURE ON FIBRE PROMOTION

    OpenAIRE

    Hill, Debbie J.; Piggott, Roley R.; Griffith, Garry R.

    1996-01-01

    In this paper the impact of changes in wool promotion expenditure and changes in expenditure on the promotion of competing fibres are examined using an equilibrium displacement model. The emphasis is on examining impacts on producer profits net of promotion expenditure and on benefit-cost ratios measuring changes in producer surplus relative to changes in promotion expenditure. It was found, for example, that incremental expenditure on apparel wool promotion on the domestic market is unprofit...

  5. Optical fibre cable selection for electricity utilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The report provides an assessment of the range of optical fibre cable solutions available, by type e.g. OPGW, ADSS, rather than by design. it also examines the key issues which will influence an electricity utilities decisions and proposes a method of evaluating the options to identify the one which most closely matches the utility's critical needs, with measurements against time, cost and quality targets. (author)

  6. Life cycle assessment of sisal fibre – Exploring how local practices can influence environmental performance

    NARCIS (Netherlands)

    Broeren, Martijn L M; Dellaert, Stijn N C; Cok, Benjamin; Patel, Martin K.; Worrell, Ernst; Shen, Li

    2017-01-01

    Sisal fibre can potentially replace glass fibre in natural fibre composites. This study focuses on the environmental performance of sisal fibre production by quantifying the greenhouse gas (GHG) emissions and energy use of producing sisal fibre in Tanzania and Brazil using life cycle assessment

  7. Oxidation of lignin in hemp fibres by laccase: effects on mechanical properties of hemp fibres and unidirectional fibre/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Baum, Andreas; Odermatt, Jürgen

    2017-01-01

    Laccase activity catalyzes oxidation and polymerization of phenols. The effect of laccase treatment on the mechanical properties of hemp fibres and hemp fibre/epoxy composites was examined. Laccase treatment on top of 0.5% EDTA + 0.2% endo-polygalacturonase (EPG) treatments increased the mechanical...

  8. Fibred Coalgebraic Logic and Quantum Protocols

    Directory of Open Access Journals (Sweden)

    Daniel Marsden

    2014-12-01

    Full Text Available Motivated by applications in modelling quantum systems using coalgebraic techniques, we introduce a fibred coalgebraic logic. Our approach extends the conventional predicate lifting semantics with additional modalities relating conditions on different fibres. As this fibred setting will typically involve multiple signature functors, the logic incorporates a calculus of modalities enabling the construction of new modalities using various composition operations. We extend the semantics of coalgebraic logic to this setting, and prove that this extension respects behavioural equivalence. We show how properties of the semantics of modalities are preserved under composition operations, and then apply the calculational aspect of our logic to produce an expressive set of modalities for reasoning about quantum systems, building these modalities up from simpler components. We then demonstrate how these modalities can describe some standard quantum protocols. The novel features of our logic are shown to allow for a uniform description of unitary evolution, and support local reasoning such as "Alice's qubit satisfies condition" as is common when discussing quantum protocols.

  9. D fibre antenna for microcellular communications

    CERN Document Server

    Bhatti, A A

    2003-01-01

    Over the years, optical fibre sensors have been developed for many application areas. With the recent growth of microcellular communication systems this area has great economic potential. Therefore with this in mind one promising application for a new optical fibre sensor system is in the detection of Radio Frequency/Electric Fields (RF/EF). By constructing such a sensor from totally dielectric materials, it could be used as an antenna for receiving radio frequency transmissions without distorting or disturbing the field lines since there are no metallic components to reflect or transmit radio frequency energy. One of the key issues in the realisation of Radio-over-Fibre (RoF) architecture is the development of an effective means of generating and transmitting the radio subcarrier. The simplest method for the optical generation of radio signals, for transmission through an optical network is to directly modulate the light source with the received RF signal. Direct modulation of the laser can lead to a number ...

  10. A fibre optic dosimeter customised for brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Suchowerska, N. [Department of Radiation Oncology, Royal Prince Alfred Hospital, Camperdown, NSW 2050 (Australia); School of Physics, University of Sydney, NSW 2006 (Australia)], E-mail: Natalka@email.cs.nsw.gov.au; Lambert, J.; Nakano, T. [Department of Radiation Oncology, Royal Prince Alfred Hospital, Camperdown, NSW 2050 (Australia); School of Physics, University of Sydney, NSW 2006 (Australia); Law, S. [School of Physics, University of Sydney, NSW 2006 (Australia); Optical Fibre Technology Centre, University of Sydney, 206 National Innovation Centre, Australian Technology Park, Eveleigh, NSW 1430 (Australia); Elsey, J. [Bandwidth Foundry Pty Ltd, Australian Technology Park, NSW, 1430 (Australia); McKenzie, D.R. [School of Physics, University of Sydney, NSW 2006 (Australia)

    2007-04-15

    In-vivo dosimetry for brachytherapy cancer treatment requires a small dosimeter with a real time readout capability that can be inserted into the patient to determine the dose to critical organs. Fibre optic scintillation dosimeters, consisting of a plastic scintillator coupled to an optical fibre, are a promising dosimeter for this application. We have implemented specific design features to optimise the performance of the dosimeter for specific in-vivo dosimetry during brachytherapy. Two sizes of the BrachyFOD{sup TM} scintillation dosimeter have been developed, with external diameters of approximately 2 and 1 mm. We have determined their important dosimetric characteristics (depth dose relation, angular dependence, energy dependence). We have shown that the background signal created by Cerenkov and fibre fluorescence does not significantly affect the performance in most clinical geometries. The dosimeter design enables readout at less than 0.5 s intervals. The clinical demands of real time in-vivo brachytherapy dosimetry can uniquely be satisfied by the BrachyFOD{sup TM}.

  11. A Fibre Optic Sensor Of Physiological Parameters

    Science.gov (United States)

    Legendre, J. P.; Forester, G. V.

    1986-11-01

    This paper presents an ultraminiature fibre optic probe capable of physiological monitoring in situ. The system has been described previously where a fibre optic reflectometer was configured as a temperature sensor and as a refractometer. For the present experiments a bare fibre tip was used as sensing element. We show that we have been able to monitor cyclic physiological parameters such as heart and respiratory rates in various animal preparations. The probe has been used to obtain signals from the oesophagus, the lower gastro-intestinal tract, the abdominal cavity and from blood vessels (arteries and veins). The probe has also measured phasic activity coincident with mechanical activity of isolated heart muscle. The small physical size of the sensor (125 µm diameter), its flexibility and the fact that it is biologically inert are all very important characteristics for medical and biological considerations. Most recently, the probe has been used to monitor cardiac and respiratory rates while obtaining NMR spectra assessing metabolic activity. This was possible only because the probe is magnetically transparent.

  12. Bundled capillary electrophoresis using microstructured fibres.

    Science.gov (United States)

    Rogers, Benjamin; Gibson, Graham T T; Oleschuk, Richard D

    2011-01-01

    Joule heating, arising from the electric current passing through the capillary, causes many undesired effects in CE that ultimately result in band broadening. The use of narrow-bore capillaries helps to solve this problem as smaller cross-sectional area results in decreased Joule heating and the rate of heat dissipation is increased by the larger surface-to-volume ratio. Issues arising from such small capillaries, such as poor detection sensitivity, low loading capacity and high flow-induced backpressure (complicating capillary loading) can be avoided by using a bundle of small capillaries operating simultaneously that share buffer reservoirs. Microstructured fibres, originally designed as waveguides in the telecommunication industry, are essentially a bundle of parallel ∼5 μm id channels that extend the length of a fibre having otherwise similar dimensions to conventional CE capillaries. This work presents the use of microstructured fibres for CZE, taking advantage of their relatively high surface-to-volume ratio and the small individual size of each channel to effect highly efficient separations, particularly for dye-labelled peptides.

  13. Applications and Properties of Fibre Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    Amit Rai1 ,

    2014-05-01

    Full Text Available In conventional concrete, micro-cracks develop before structure is loaded because of drying shrinkage and other causes of volume change. When the structure is loaded, the micro cracks open up and propagate because of development of such micro-cracks, results in inelastic deformation in concrete. Fibre reinforced concrete (FRC is cementing concrete reinforced mixture with more or less randomly distributed small fibres. In the FRC, a numbers of small fibres are dispersed and distributed randomly in the concrete at the time of mixing, and thus improve concrete properties in all directions. The fibers help to transfer load to the internal micro cracks. FRC is cement based composite material that has been developed in recent years. It has been successfully used in construction with its excellent flexural-tensile strength, resistance to spitting, impact resistance and excellent permeability and frost resistance. It is an effective way to increase toughness, shock resistance and resistance to plastic shrinkage cracking of the mortar. These fibers have many benefits. Steel fibers can improve the structural strength to reduce in the heavy steel reinforcement requirement. Freeze thaw resistance of the concrete is improved. Durability of the concrete is improved to reduce in the crack widths. Polypropylene and Nylon fibers are used to improve the impact resistance. Many developments have been made in the fiber reinforced concrete.

  14. Chronological ageing of human hair keratin fibres.

    Science.gov (United States)

    Thibaut, S; de Becker, E; Bernard, B A; Huart, M; Fiat, F; Baghdadli, N; Luengo, G S; Leroy, F; Angevin, P; Kermoal, A M; Muller, S; Peron, M; Provot, G; Kravtchenko, S; Saint-Léger, D; Desbois, G; Gauchet, L; Nowbuth, K; Galliano, A; Kempf, J Y; Silberzan, I

    2010-12-01

    Examination of very long hair (length > 2.4 m) using a large range of evaluation methods including physical, chemical, biochemical and microscopic techniques has enabled to attain a detailed understanding of natural ageing of human hair keratin fibres. Scrutinizing hair that has undergone little or no oxidative aggression--because of the absence of action of chemical agents such as bleaching or dyeing--from the root to the tip shows the deterioration process, which gradually takes place from the outside to the inside of the hair shaft: first, a progressive abrasion of the cuticle, whilst the cortex structure remains unaltered, is evidenced along a length of roughly 1 m onwards together with constant shine, hydrophobicity and friction characteristics. Further along the fibre, a significant damage to cuticle scales occurs, which correlates well with ceramides and 18-Methyl Eicosanoic Acid (18-MEA) decline, and progressive decrease in keratin-associated protein content. Most physical descriptors of mechanical and optical properties decay significantly. This detailed description of natural ageing of human hair fibres by a fine analysis of hair components and physical parameters in relationship with cosmetic characteristics provides a time-dependent 'damage scale' of human hair, which may help in designing new targeted hair care formulations.

  15. Fibre optic portable rail vehicle detector

    Science.gov (United States)

    Kepak, Stanislav; Cubik, Jakub; Zavodny, Petr; Hejduk, Stanislav; Nedoma, Jan; Davidson, Alan; Vasinek, Vladimir

    2016-12-01

    During track maintenance operations, the early detection of oncoming rail vehicles is critical for the safety of maintenance personnel. In addition, the detection system should be simple to install at the trackside by minimally qualified personnel. Fibre optic based sensor systems have the inherent advantages of being passive, unaffected by radio frequency interference (RFI) and suffering very low signal attenuation. Such a system therefore represents a good alternative to conventional approaches such as ultrasonic based sensor systems. The proposed system consists of one or more passive fibre trackside sensors and an x86 processing unit located at the work site. The solid fibre connection between sensors and processing unit eliminates the risk of RFI. In addition, the detection system sensors are easy to install with no requirement for electrical power at the sensor site. The system was tested on a tram line in Ostrava with the results obtained indicating the successful detection of all the trams in the monitoring windows using a single sensor. However, the platform allows flexibility in configuring multiple sensors where required by system users.

  16. Unidirectional Cordenka Fibre-Reinforced Furan Resin Full Biocomposite: Properties and Influence of High Fibre Mass Fraction

    Directory of Open Access Journals (Sweden)

    Talent Malaba

    2015-01-01

    Full Text Available A full biocomposite was fabricated from Cordenka CR fibre and furan resin. High fibre mass fractions (FMF were achieved by pressing the CR fibres into unidirectional sheets prior to incorporation into the resin. Results of testing indicated that the tensile properties of the biocomposite were improved by the initial increase of FMF from 51 to 64%, with a subsequent increase of FMF to 75% resulting in a deterioration of those properties. Examination of the tensile fracture surfaces with a scanning electron microscope (SEM revealed moderate deterioration in fibre-matrix adhesion after the initial increase of FMF. Further increase of the FMF to 75% was shown by SEM to result in worse fibre-matrix adhesion. On the other hand, the flexural, interlaminar-shear, and dynamic mechanical properties were adversely affected by the increase in fibre-mass fraction from 51 through 75%. These effects were mainly attributed to reduced fibre wetting that resulted in weakened fibre-matrix interfacial bonding and subsequent poor stress exchange at the fibre-matrix interface. Observations made with a digital microscope revealed normal crack behaviour in the laminated composite, and the shear fracture modes were I and II. This biocomposite has mechanical properties comparable to those of flax and glass fibre-reinforced furan resin biocomposites.

  17. Influence of an Optimized Fibre Coating on Interfacial and Mechanical Properties of Glass Fibre/Polypropylene Composites

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The influence of pretreatment of fibre on interfacial and mechanical properties of glass fibre/polypropylene composites was investigated. Firstly, the glass fibres were coated with the blends of m-IPP (maleic anhydride grafting isotatic polypropylene) and m-APP (maleic anhydride grafting amorphous polypropylene) in different ratios.Secondly, the interfacial reaction of the coated composites was analysed by FTIR, which shows that the interfacial chemical reaction between m-IPP/m-APP in the fibre coating and the fibre surface-bound coupling agent is in existence.Thirdly, the microstructure of the coated composites was studied by SEM. The results indicate that the coating treatment is effective on improving interfacial adhesion of the fibre-matrix and the right amount of m-APP added to the coat impels the plastic deformation surrounding the point of cracks, which makes cracks turn to region and prevents from further interface debonding. Lastly, the mechanical properties were evaluated by measurement of the flexural strength and impact strength of the composites. It was found that the flexural strength and impact strength of the composites with coating fibre are higher than those of uncoating fibre composite. The results of these investigations draw the conclusion that the pretreatment of fibre with m-IPP/m-APP blends can form an optimize interlayer between the fibre and the PP matrix, which improves both the strength and toughness of the composites.

  18. Skinned fibres produce the same power and force as intact fibre bundles from muscle of wild rabbits.

    Science.gov (United States)

    Curtin, Nancy A; Diack, Rebecca A; West, Timothy G; Wilson, Alan M; Woledge, Roger C

    2015-09-01

    Skinned fibres have advantages for comparing the muscle properties of different animal species because they can be prepared from a needle biopsy taken under field conditions. However, it is not clear how well the contractile properties of skinned fibres reflect the properties of the muscle fibres in vivo. Here, we compare the mechanical performance of intact fibre bundles and skinned fibres from muscle of the same animals. This is the first such direct comparison. Maximum power and isometric force were measured at 25 °C using peroneus longus (PL) and extensor digiti-V (ED-V) muscles from wild rabbits (Oryctolagus cuniculus). More than 90% of the fibres in these muscles are fast-twitch, type 2 fibres. Maximum power was measured in force-clamp experiments. We show that maximum power per volume was the same in intact (121.3 ± 16.1 W l(-1), mean ± s.e.m.; N=16) and skinned (122.6 ± 4.6 W l(-1); N=141) fibres. Maximum relative power (power/F(IM) Lo, where F(IM) is maximum isometric force and Lo is standard fibre length) was also similar in intact (0.645 ± 0.037; N=16) and skinned (0.589 ± 0.019; N=141) fibres. Relative power is independent of volume and thus not subject to errors in measurement of volume. Finally, maximum isometric force per cross-sectional area was also found to be the same for intact and skinned fibres (181.9 kPa ± 19.1; N=16; 207.8 kPa ± 4.8; N=141, respectively). These results contrast with previous measurements of performance at lower temperatures where skinned fibres produce much less power than intact fibres from both mammals and non-mammalian species. © 2015. Published by The Company of Biologists Ltd.

  19. Advances in infrared and imaging fibres for astronomical instrumentation

    CERN Document Server

    Haynes, R; Marcel, J; Jovanovic, N; Haynes, Roger; Namara, Pam Mc; Marcel, Jackie; Jovanovic, Nemanja

    2006-01-01

    Optical fibres have already played a huge part in ground based astronomical instrumentation, however, with the revolution in photonics currently taking place new fibre technologies and integrated optical devices are likely to have a profound impact on the way we manipulate light in the future. The Anglo-Australian Observatory, along with partners at the Optical Fibre Technology Centre of the University of Sydney, is investigating some of the developing technologies as part of our Astrophotonics programme. In this paper we discuss the advances that have been made with infrared transmitting fibre, both conventional and microstructured, in particular those based on flouride glasses. Flouride glasses have a particularly wide transparent region from the UV through to around 7um, whereas silica fibres, commonly used in astronomy, only transmit out to about 2um. We discuss the impact of advances in fibre manufacture that have greatly improved the optical, chemical resistance and physical properties of the flouride f...

  20. Erbium-doped nanoparticles in silica-based optical fibres

    CERN Document Server

    Blanc, Wilfried; Dussardier, Bernard; 10.1504/IJNT.2012.045350

    2012-01-01

    Developing of new rare-earth (RE)-doped optical fibres for power amplifiers and lasers requires continuous improvements in the fibre spectroscopic properties (like shape and width of the gain curve, optical quantum efficiency, resistance to spectral hole burning and photodarkening...). Silica glass as a host material for fibres has proved to be very attractive. However, some potential applications of RE-doped fibres suffer from limitations in terms of spectroscopic properties resulting from clustering or inappropriate local environment when doped into silica. To this aim, we present a new route to modify some spectroscopic properties of RE ions in silica-based fibres based on the incorporation of erbium ions in amorphous dielectric nanoparticles, grown in-situ in fibre preforms. By adding alkaline earth elements, in low concentration into silica, one can obtain a glass with an immiscibility gap. Then, phase separation occurs under an appropriate heat treatment. We investigated the role of three alkaline-earth...