Inclusion of mobile telephone numbers into an ongoing population health survey in New South Wales, Australia, using an overlapping dual-frame design: impact on the time series.

Science.gov (United States)

Barr, Margo L; Ferguson, Raymond A; Steel, David G

2014-08-12

Since 1997, the NSW Population Health Survey (NSWPHS) had selected the sample using random digit dialing of landline telephone numbers. When the survey began coverage of the population by landline phone frames was high (96%). As landline coverage in Australia has declined and continues to do so, in 2012, a sample of mobile telephone numbers was added to the survey using an overlapping dual-frame design. Details of the methodology are published elsewhere. This paper discusses the impacts of the sampling frame change on the time series, and provides possible approaches to handling these impacts. Prevalence estimates were calculated for type of phone-use, and a range of health indicators. Prevalence ratios (PR) for each of the health indicators were also calculated using Poisson regression analysis with robust variance estimation by type of phone-use. Health estimates for 2012 were compared to 2011. The full time series was examined for selected health indicators. It was estimated from the 2012 NSWPHS that 20.0% of the NSW population were mobile-only phone users. Looking at the full time series for overweight or obese and current smoking if the NSWPHS had continued to be undertaken only using a landline frame, overweight or obese would have been shown to continue to increase and current smoking would have been shown to continue to decrease. However, with the introduction of the overlapping dual-frame design in 2012, overweight or obese increased until 2011 and then decreased in 2012, and current smoking decreased until 2011, and then increased in 2012. Our examination of these time series showed that the changes were a consequence of the sampling frame change and were not real changes. Both the backcasting method and the minimal coverage method could adequately adjust for the design change and allow for the continuation of the time series. The inclusion of the mobile telephone numbers, through an overlapping dual-frame design, did impact on the time series for some of

Mobility-limiting mechanisms in single and dual channel strained Si/SiGe MOSFETs

International Nuclear Information System (INIS)

Olsen, S.H.; Dobrosz, P.; Escobedo-Cousin, E.; Bull, S.J.; O'Neill, A.G.

2005-01-01

Dual channel strained Si/SiGe CMOS architectures currently receive great attention due to maximum performance benefits being predicted for both n- and p-channel MOSFETs. Epitaxial growth of a compressively strained SiGe layer followed by tensile strained Si can create a high mobility buried hole channel and a high mobility surface electron channel on a single relaxed SiGe virtual substrate. However, dual channel n-MOSFETs fabricated using a high thermal budget exhibit compromised mobility enhancements compared with single channel devices, in which both electron and hole channels form in strained Si. This paper investigates the mobility-limiting mechanisms of dual channel structures. The first evidence of increased interface roughness due to the introduction of compressively strained SiGe below the tensile strained Si channel is presented. Interface corrugations degrade electron mobility in the strained Si. Roughness measurements have been carried out using AFM and TEM. Filtering AFM images allowed roughness at wavelengths pertinent to carrier transport to be studied and the results are in agreement with electrical data. Furthermore, the first comparison of strain measurements in the surface channels of single and dual channel architectures is presented. Raman spectroscopy has been used to study channel strain both before and after processing and indicates that there is no impact of the buried SiGe layer on surface macrostrain. The results provide further evidence that the improved performance of the single channel devices fabricated using a high thermal budget arises from improved surface roughness and reduced Ge diffusion into the Si channel

Designing Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

are often still not engaged with in a sufficiently manner. Often social sciences keep distance to the physical and material as if the social was still to be understood as a realm separate of technology, architecture, and design (for a critique of this see; Latour 2005 and Urry 2000). This paper takes point......Within the so-called ‘mobilities turn’ (Adey 2010; Cresswell 2006; Urry 2007) much research has taken place during the last decade bringing mobilities into the centre of sociological analysis. However, the materiality and spatiality of artefacts, infrastructures, and sites hosting mobilities...... of departure in the sociological perspective termed ‘Staging Mobilities’ (Jensen 2013a) and utilizes this as an analytical frame for exploring cases of mobility design. The paper put focus on how the material shape, design and architectures of technologies, spaces and sites influence mobilities practices...

Mobilities Design

DEFF Research Database (Denmark)

Jensen, Ole B.; Lanng, Ditte Bendix

Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the background of the ‘mobilities turn’ (e.g. Cresswell 2006, Urry 2007) this book articulates a new and emerging research field, namely that of ‘m......Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the background of the ‘mobilities turn’ (e.g. Cresswell 2006, Urry 2007) this book articulates a new and emerging research field, namely...... that of ‘mobilities design’. The book revolves around the following research question: How are design decisions and interventions staging mobilities? It builds upon the Staging Mobilities model (Jensen 2013) in an explorative inquiry into the problems and potentials of the design of mobilities. The exchange value...

Inclusion of mobile phone numbers into an ongoing population health survey in New South Wales, Australia: design, methods, call outcomes, costs and sample representativeness.

Science.gov (United States)

Barr, Margo L; van Ritten, Jason J; Steel, David G; Thackway, Sarah V

2012-11-22

In Australia telephone surveys have been the method of choice for ongoing jurisdictional population health surveys. Although it was estimated in 2011 that nearly 20% of the Australian population were mobile-only phone users, the inclusion of mobile phone numbers into these existing landline population health surveys has not occurred. This paper describes the methods used for the inclusion of mobile phone numbers into an existing ongoing landline random digit dialling (RDD) health survey in an Australian state, the New South Wales Population Health Survey (NSWPHS). This paper also compares the call outcomes, costs and the representativeness of the resultant sample to that of the previous landline sample. After examining several mobile phone pilot studies conducted in Australia and possible sample designs (screening dual-frame and overlapping dual-frame), mobile phone numbers were included into the NSWPHS using an overlapping dual-frame design. Data collection was consistent, where possible, with the previous years' landline RDD phone surveys and between frames. Survey operational data for the frames were compared and combined. Demographic information from the interview data for mobile-only phone users, both, and total were compared to the landline frame using χ2 tests. Demographic information for each frame, landline and the mobile-only (equivalent to a screening dual frame design), and the frames combined (with appropriate overlap adjustment) were compared to the NSW demographic profile from the 2011 census using χ2 tests. In the first quarter of 2012, 3395 interviews were completed with 2171 respondents (63.9%) from the landline frame (17.6% landline only) and 1224 (36.1%) from the mobile frame (25.8% mobile only). Overall combined response, contact and cooperation rates were 33.1%, 65.1% and 72.2% respectively. As expected from previous research, the demographic profile of the mobile-only phone respondents differed most (more that were young, males, Aboriginal

Improving balance, mobility, and dual-task performance in an adolescent with cerebral palsy: A case report.

Science.gov (United States)

Fisher-Pipher, Sarah; Kenyon, Lisa K; Westman, Marci

2017-07-01

Improving functional mobility is often a desired outcome for adolescents with cerebral palsy (CP). Traditional neurorehabilitation approaches are frequently directed at impairments; however, improvements may not be carried over into functional mobility. The purpose of this case report was to describe the examination, intervention, and outcomes of a task-oriented physical therapy intervention program to improve dynamic balance, functional mobility, and dual-task performance in an adolescent with CP. The participant was a 15-year-old girl with spastic triplegic CP (Gross Motor Classification System Level II). Examination procedures included the Canadian Occupational Performance Measure, 6-minute walk test, Muscle Power Sprint Test, 10 x 5-meter sprint test, Timed Up and Down Stairs Test, Gross Motor Function Measure, Gillette Functional Assessment Questionnaire, and functional lower extremity strength tests. Intervention focused on task-oriented dynamic balance and mobility tasks that incorporated coordination and speed demands as well as task-specific lower extremity and trunk strengthening activities. Dual task demands were integrated into all intervention activities. Post-intervention testing revealed improvements in cardiovascular endurance, anaerobic power, agility, stair climbing, gross motor skills, and mobility. The participant appeared to benefit from a task-oriented program to improve dynamic balance, functional mobility, and dual-task performance.

Mobilities Design

DEFF Research Database (Denmark)

Jensen, Ole B.; Lanng, Ditte Bendix

2016-01-01

of life’ for billions of people in the everyday life. This paper is structured in three parts. After the general introduction we present the mobilities theory perspective of ‘staging mobilities’ and connects this to the empirical phenomenon of parking lots and their design. The paper ends in section three......Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the backgound of the ‘mobilities turn’ (for short review paper on this see; Sheller 2011, Vannini 2010) this paper proposes a further development...... of the perspective in the direction of a material and design oriented turn. In order to fulfill this purpose we articulate a new and emerging research field, namely that of ‘mobilities design’. In our understanding time has come to articulate ‘Mobilities Design’ as a dedicated research field in and of its own...

Development of design technology for dual-cooled fuel

International Nuclear Information System (INIS)

Kim, Hyung Kyu; Yoon, Kyung Ho; Lee, Young Ho

2010-03-01

Primary purpose of the project is to complete a basic design of the power uprating dual-cooled fuel's structural components for an actual use in the existing nuclear power plants. It also includes a basic design of the components of a dual-cooled fuel rod. To this end, during the three years of the first stage (2007.03.∼2010.02.), concepts and technical issues of the structural components such as a supporting structure, guide thimbles and instrumentation tube and the top and bottom end pieces were derived in order to comply with the functional requirements and design criteria of them. Basic design was carried out to resolve the issues by using analytical methods as well as experiments, and observed finally is that a structural compatibility of the designed dual-cooled fuel to the Korean Standard Nuclear Power Plant (OPR-1000). As for the dual-cooled fuel rod's components such as a plenum spring, a spacer and end plugs, a concept of them was established by using the basic dimension and array produced by other sub-projects. In turn, the basic design was completed by using the finite element analysis and conventional mechanical design formulae. Additionally, a welding method and equipment for a dual-cooled fuel rod specimen was also successfully developed to prepare for the irradiation tests at the HANARO. It was shown that a dual-cooed fuel for the OPR-1000 can be designed after manufacturing the partial assembly with the designed components and their drawings. The first stage was completed with passing the Gate checks proposed at the beginning. During the second stage(2010.03.∼2012.02.), researches on the mechanical behavior and structural integrity of the designed dual-cooled fuel will be conducted for preparing a license of it, which should be done when the dual-cooled fuel is commercialized

Cost-effective handoff scheme based on mobility-aware dual pointer forwarding in proxy mobile IPv6 networks.

Science.gov (United States)

Son, Seungsik; Jeong, Jongpil

2014-01-01

In this paper, a mobility-aware Dual Pointer Forwarding scheme (mDPF) is applied in Proxy Mobile IPv6 (PMIPv6) networks. The movement of a Mobile Node (MN) is classified as intra-domain and inter-domain handoff. When the MN moves, this scheme can reduce the high signaling overhead for intra-handoff/inter-handoff, because the Local Mobility Anchor (LMA) and Mobile Access Gateway (MAG) are connected by pointer chains. In other words, a handoff is aware of low mobility between the previously attached MAG (pMAG) and newly attached MAG (nMAG), and another handoff between the previously attached LMA (pLMA) and newly attached LMA (nLMA) is aware of high mobility. Based on these mobility-aware binding updates, the overhead of the packet delivery can be reduced. Also, we analyse the binding update cost and packet delivery cost for route optimization, based on the mathematical analytic model. Analytical results show that our mDPF outperforms the PMIPv6 and the other pointer forwarding schemes, in terms of reducing the total cost of signaling.

Design of high–order HTS dual–band bandpass filters with receiver subsystem for future mobile communication systems

Energy Technology Data Exchange (ETDEWEB)

Sekiya, N., E-mail: nsekiya@yamanashi.ac.jp

2016-08-15

Highlights: • We have developed two high-order HTS dual-band BPFs with a receiver subsystem for future mobile communication systems. • We developed a method for flexibly adjusting the coupling coefficient for the two passbands. • We demonstrated an HTS dual-band BPF receiver subsystem that uses a pulse tube cryocooler and a wideband LNA. • The proposed BPF is evaluated by simulation and measurement with good agreement. - Abstract: We have developed two high-order high-temperature superconducting (HTS) dual-band bandpass filters (BPFs) with a receiver subsystem for future mobile communication systems. They feature stub-loaded hair-pin resonators with two types of microstrip lines between them. One has a six-pole design, and the other has an eight-pole design. Both were designed to operate at 2.15 GHz with a 43-MHz (2%) bandwidth for the lower passband and at 3.50 GHz with a 70-MHz (2%) bandwidth for the upper one. They were fabricated using YBa{sub 2}Cu{sub 3}O{sub y} thin film on a CeO{sub 2}-bufferd r-Al{sub 2}O{sub 3} substrate. The measured results for both filters agree well with the simulated ones. The HTS dual-band BPF receiver subsystem uses a pulse tube cryocooler and a wideband low noise amplifier (LNA). We measured the frequency response of the six-pole dual-band BPF with and without a wideband LNA with a gain of 10 dB. The measured return losses were close.

Near-Optimal Tracking Control of Mobile Robots Via Receding-Horizon Dual Heuristic Programming.

Science.gov (United States)

Lian, Chuanqiang; Xu, Xin; Chen, Hong; He, Haibo

2016-11-01

Trajectory tracking control of wheeled mobile robots (WMRs) has been an important research topic in control theory and robotics. Although various tracking control methods with stability have been developed for WMRs, it is still difficult to design optimal or near-optimal tracking controller under uncertainties and disturbances. In this paper, a near-optimal tracking control method is presented for WMRs based on receding-horizon dual heuristic programming (RHDHP). In the proposed method, a backstepping kinematic controller is designed to generate desired velocity profiles and the receding horizon strategy is used to decompose the infinite-horizon optimal control problem into a series of finite-horizon optimal control problems. In each horizon, a closed-loop tracking control policy is successively updated using a class of approximate dynamic programming algorithms called finite-horizon dual heuristic programming (DHP). The convergence property of the proposed method is analyzed and it is shown that the tracking control system based on RHDHP is asymptotically stable by using the Lyapunov approach. Simulation results on three tracking control problems demonstrate that the proposed method has improved control performance when compared with conventional model predictive control (MPC) and DHP. It is also illustrated that the proposed method has lower computational burden than conventional MPC, which is very beneficial for real-time tracking control.

Mobilizing Senior Citizens in Co-Design of Mobile Technology

DEFF Research Database (Denmark)

Malmborg, Lone; Gronvall, Erik; Messeter, Jörn

2016-01-01

. Based on the notions of design culture, communities of everyday practice and situated elderliness we present accounts from two European countries, and discuss methodological issues related to mobilizing senior citizens in co-design work as they have manifested themselves and influenced the Give......This paper disseminates work from the European Give&Take project, which aims at co-designing service sharing among senior citizens based on a mobile and distributed platform. With this project as a frame, our paper addresses methodological considerations of participation in co-design for ageing......&Take project. Challenges for mobilization are identified, based on an analysis of attitudes and values among design researchers and senior citizens. This analysis lead us to identify and discuss three strategies for mobilizing senior citizens in co-design of mobile technology: 1) Understanding being ‘elderly...

Mobile Design Pattern Gallery UI Patterns for Mobile Applications

CERN Document Server

Neil, Theresa

2012-01-01

When you're under pressure to produce a well designed, easy-to-navigate mobile app, there's no time to reinvent the wheel. This concise book provides a handy reference to 70 mobile app design patterns, illustrated by more than 400 screenshots from current iOS, Android, BlackBerry, WebOS, Windows Mobile, and Symbian apps. User experience professional Theresa Neil (Designing Web Interfaces) walks you through design patterns in 10 separate categories, including anti-patterns. Whether you're designing a simple iPhone application or one that's meant to work for every popular mobile OS on the mark

Optimal Design of Dual-Hop VLC/RF Communication System With Energy Harvesting

KAUST Repository

Rakia, Tamer

2016-07-28

In this letter, we consider a dual-hop heterogeneous visible light communication (VLC)/radio frequency (RF) communication system to extend the coverage of VLC systems. Besides detecting the information over VLC link, the relay is able to harvest energy from the first-hop VLC link, by extracting the direct current component of the received optical signal, and uses the harvested energy to retransmit the data to a mobile terminal over the second-hop RF link. We investigate the optimal design of the hybrid system in terms of data rate maximization.

Dual mobility cup reduces dislocation rate after arthroplasty for femoral neck fracture

Directory of Open Access Journals (Sweden)

Robertsson Otto

2010-08-01

Full Text Available Abstract Background Hip dislocation after arthroplasty for femoral neck fractures remains a serious complication. The aim of our study was to investigate the dislocation rate in acute femoral neck fracture patients operated with a posterior approach with cemented conventional or dual articulation acetabular components. Methods We compared the dislocation rate in 56 consecutive patients operated with conventional (single mobility cemented acetabular components to that in 42 consecutive patients operated with dual articulation acetabular components. All the patients were operated via posterior approach and were followed up to one year postoperatively. Results There were 8 dislocations in the 56 patients having conventional components as compared to no dislocations in those 42 having dual articulation components (p = 0.01. The groups were similar with respect to age and gender distribution. Conclusions We conclude that the use of a cemented dual articulation acetabular component significantly reduces the dislocation rates in femoral neck fracture patients operated via posterior approach.

Mobilities of Language and Literacy Ideologies: Dual Language Graduates' Bilingualism and Biliteracy

Science.gov (United States)

Granados, Nadia R.

2017-01-01

Using qualitative methodology, this research examines how graduates of a K-5 dual language immersion program have experienced multiple and competing social, cultural, institutional, and political forces at play in complex processes that ultimately affect one's mobilities of language, literacy, and learning. These students have now grown into…

Client Mobile Software Design Principles for Mobile Learning Systems

Directory of Open Access Journals (Sweden)

Qing Tan

2009-01-01

Full Text Available In a client-server mobile learning system, client mobile software must run on the mobile phone to acquire, package, and send student’s interaction data via the mobile communications network to the connected mobile application server. The server will receive and process the client data in order to offer appropriate content and learning activities. To develop the mobile learning systems there are a number of very important issues that must be addressed. Mobile phones have scarce computing resources. They consist of heterogeneous devices and use various mobile operating systems, they have limitations with their user/device interaction capabilities, high data communications cost, and must provide for device mobility and portability. In this paper we propose five principles for designing Client mobile learning software. A location-based adaptive mobile learning system is presented as a proof of concept to demonstrate the applicability of these design principles.

Staging Mobilities / Designing Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

2015-01-01

, and systems 'hosting' these multiple and complex mobilities are designed and how they are staging these in terms of their physical layout. By analysing specific cases of ‘mobilities design’ related to the four modes of moving; Walk, Bike, Train, and Car, the book uncover important and until now neglected...... is more than movement between point A and B. It explores how the movement of people, goods, information, and signs influences human understandings of self, other and the built environment. Moving towards a new understanding of the relationship between movement, interaction and environments, the project...

A Novel Approach for Designing Mobile Native Apps

Directory of Open Access Journals (Sweden)

Sasmita Pani

2017-01-01

Full Text Available Mobile devices are differed from desktop based systems in terms of particular execution environment, constrained resources, and high mobility requirement. To overcome these shortcomings, various agile based methodologies are developed for native mobile applications such as Mobile-D, Scrum etc. These agile techniques are based on various phases and these phases begin from exploring, initializing and implementing the mobile apps. But these techniques are not focusing on elaborating design model for mobile native apps. The aim of the paper is to provide a layered approach or layered model for design of mobile native apps which can be used as a framework for developing mobile native apps. Any mobile native app developer can use this sequential approach or design model for design and development of mobile native apps. This design model gives a standard or framework, based on which generic native mobile apps can be designed and developed. This paper also shows an empirical analysis among the web app design models with the proposed design model for mobile native app development.

A stroller ethnography of mobilities design

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

This paper explores a neglected mode of mobility through an ethnographic study of pram strollers in Copenhagen. I illustrate the analytic advantages of using the recent mobilities design turn to explore how pram strolling is conditioned by material designs and experienced through affective...... properties and experiential effects of urban surfaces. In this process, I relate pram mobility to questions of urban accessibility issues and discuss urban design interventions, not as transient inconveniencies, but enduring predicaments for wheeled-based mobility in the contemporary city....

HTS dual-band bandpass filters using stub-loaded hair-pin resonators for mobile communication systems

Energy Technology Data Exchange (ETDEWEB)

Sekiya, N., E-mail: nsekiya@yamanashi.ac.jp; Sugiyama, S.

2014-09-15

Highlights: • We have developed a HTS five-pole dual-band bandpass filter using stub-loaded hair-pin resonators. • The proposed dual-band BPF can independently control of the center frequency. • Flexibly adjustment of the bandwidth can be achieved by the H-shaped waveguide. • The proposed BPF is evaluated by simulation and measurement with good agreement. - Abstract: A HTS dual-band bandpass filter is developed to obtain sharp-cut off characteristics for mobile communication systems. The filter is composed of five stub-loaded hair-pin resonators with H-shaped waveguides between them. The main advantage of the proposed filter is to allow independent control of the center frequency of the first and second bands. The bandwidths can be flexibly adjusted using the H-shaped waveguide. An electromagnetic simulator was used to design and analyze the filter, which have a 3.5-GHz center frequency and a 70-MHz (2%) bandwidth for the first band and a 5.0-GHz center frequency and a 100-MHz (2%) bandwidth for the second band. The filter was fabricated using YBa{sub 2}Cu{sub 3}O{sub y} thin film on an Al{sub 2}O{sub 3} substrate. Ground plane was fabricated using Au thin film. The measured frequency responses of the filter tally well with the simulated ones.

Plug-and-Design: Bringing a Design Environment to a Mobile Device

OpenAIRE

MESKENS, Jan; LUYTEN, Kris; CONINX, Karin

2009-01-01

Due to the large amount of mobile devices that continue to appear on the consumer market, mobile user interface design becomes increasingly important. The major issue with many existing mobile user interface design approaches is the time and effort that is needed to deploy a user interface design to the target device. In order to address this issue, we propose the plug-and-design tool that relies on a continuous multi-device mouse pointer to design user interfaces directly on the mobile targe...

Transmission and signal loss in mask designs for a dual neutron and gamma imager applied to mobile standoff detection

International Nuclear Information System (INIS)

Ayaz-Maierhafer, Birsen; Hayward, Jason P.; Ziock, Klaus P.; Blackston, Matthew A.; Fabris, Lorenzo

2013-01-01

In order to design a next-generation, dual neutron and gamma imager for mobile standoff detection which uses coded aperture imaging as its primary detection modality, the following design parameters have been investigated for gamma and neutron radiation incident upon a hybrid, coded mask: (1) transmission through mask elements for various mask materials and thicknesses; and (2) signal attenuation in the mask versus angle of incidence. Each of these parameters directly affects detection significance, as quantified by the signal-to-noise ratio. The hybrid mask consists of two or three layers: organic material for fast neutron attenuation and scattering, Cd for slow neutron absorption (if applied), and one of three of the following photon or photon and slow neutron attenuating materials—Linotype alloy, CLYC, or CZT. In the MCNP model, a line source of gamma rays (100–2500 keV), fast neutrons (1000–10,000 keV) or thermal neutrons was positioned above the hybrid mask. The radiation penetrating the mask was simply tallied at the surface of an ideal detector, which was located below the surface of the last mask layer. The transmission was calculated as the ratio of the particles transmitted through the fixed aperture to the particles passing through the closed mask. In order to determine the performance of the mask considering relative motion between the source and detector, simulations were used to calculate the signal attenuation for incident radiation angles of 0–50°. The results showed that a hybrid mask can be designed to sufficiently reduce both transmission through the mask and signal loss at large angles of incidence, considering both gamma ray and fast neutron radiations. With properly selected material thicknesses, the signal loss of a hybrid mask, which is necessarily thicker than the mask required for either single mode imaging, is not a setback to the system's detection significance

A Website Design with the Mobile-first Approach

OpenAIRE

Satyal, Umesh

2016-01-01

This thesis aims to explain the mobile first design approach in web design and development and its advantages over other prevalent approaches. In the study, the mobile web, its trends and different approaches for design and developing a mobile first web application are described and a comparison between mobile sites and mobile first sites is made. The concept of responsive web design and different grid systems are discussed as they are essential factors for responsive web design. Duri...

Determining Reliability of a Dual-Task Functional Mobility Protocol for Individuals With Lower Extremity Amputation.

Science.gov (United States)

Hunter, Susan W; Frengopoulos, Courtney; Holmes, Jeff; Viana, Ricardo; Payne, Michael W

2018-04-01

To determine the relative and absolute reliability of a dual-task functional mobility assessment. Cross-sectional study. Academic rehabilitation hospital. Individuals (N=60) with lower extremity amputation attending an outpatient amputee clinic (mean age, 58.21±12.59y; 18, 80% male) who were stratified into 3 groups: (1) transtibial amputation of vascular etiology (n=20); (2) transtibial amputation of nonvascular etiology (n=20); and (3) transfemoral or bilateral amputation of any etiology (n=20). Not applicable. Time to complete the L Test measured functional mobility under single- and dual-task conditions. The addition of a cognitive task (serial subtractions by 3's) created dual-task conditions. Single-task performance on the cognitive task was also reported. Intraclass correlation coefficients (ICCs) measured relative reliability; SEM and minimal detectable change with a 95% confidence interval (MDC 95 ) measured absolute reliability. Bland-Altman plots measured agreement between assessments. Relative reliability results were excellent for all 3 groups. Values for the dual-task L Test for those with transtibial amputation of vascular etiology (n=20; mean age, 60.36±7.84y; 19, 90% men) were ICC=.98 (95% confidence interval [CI], .94-.99), SEM=1.36 seconds, and MDC 95 =3.76 seconds; for those with transtibial amputation of nonvascular etiology (n=20; mean age, 55.85±14.08y; 17, 85% men), values were ICC=.93 (95% CI, .80-.98), SEM=1.34 seconds, and MDC 95 =3.71 seconds; and for those with transfemoral or bilateral amputation (n=20; mean age, 58.21±14.88y; 13, 65% men), values were ICC=.998 (95% CI, .996-.999), SEM=1.03 seconds, and MDC 95 =2.85 seconds. Bland-Altman plots indicated that assessments did not vary systematically for each group. This dual-task assessment protocol achieved approved levels of relative reliability values for the 3 groups tested. This protocol may be used clinically or in research settings to assess the interaction between cognition

Designing Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

How is the width of the pavement shaping the urban experience? How is the material design of transport infrastructure and mobile technology affording social interaction in everyday life spaces? How do people inhabit these spaces with their bodies and in accordance to social and cultural norms...

Plug-and-Design: Embracing Mobile Devices as Part of the Design Environment

OpenAIRE

MESKENS, Jan; LUYTEN, Kris; CONINX, Karin

2009-01-01

Due to the large amount of mobile devices that continue to appear on the consumer market, mobile user interface design becomes increasingly important. The major issue with many existing mobile user interface design approaches is the time and effort that is needed to deploy a user interface design to the target device. In order to address this issue, we propose the plug-and-design tool that relies on a continuous multi-device mouse pointer to design user interfaces directly on the mobile targe...

Design and Implementation of Dual-Mode Wireless Video Monitoring System

Directory of Open Access Journals (Sweden)

BAO Song-Jian

2014-10-01

Full Text Available Dual-mode wireless video transmission has two major problems. Firstly, one is time delay difference bringing about asynchronous reception decoding frame error phenomenon; secondly, dual-mode network bandwidth inconformity causes scheduling problem. In order to solve above two problems, a kind of TD-SCDMA/CDMA20001x dual-mode wireless video transmission design method is proposed. For the solution of decoding frame error phenomenon, the design puts forward adding frame identification and packet preprocessing at the sending and synchronizing combination at the receiving end. For the solution of scheduling problem, the wireless communication channel cooperative work and video data transmission scheduling management algorithm is proposed in the design.

Mobile Design and Development Practical concepts and techniques for creating mobile sites and web apps

CERN Document Server

Fling, Brian

2009-01-01

Mobile devices outnumber desktop and laptop computers three to one worldwide, yet little information is available for designing and developing mobile applications. Mobile Design and Development fills that void with practical guidelines, standards, techniques, and best practices for building mobile products from start to finish. With this book, you'll learn basic design and development principles for all mobile devices and platforms. You'll also explore the more advanced capabilities of the mobile web, including markup, advanced styling techniques, and mobile Ajax. If you're a web designer,

Numerical simulation of air flow through turbocharger compressors with dual volute design

Energy Technology Data Exchange (ETDEWEB)

Jiao, Kui; Li, Xianguo; Wu, Hao [Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON (Canada); Sun, Harold; Schram, Tim [Ford Motor Company, Dearborn, MI 48126 (United States); Krivitzky, Eric; Larosiliere, Louis M. [Concepts NREC, White River Junction, VT 05001 (United States)

2009-11-15

In this paper, turbocharger centrifugal compressors with dual volute design were investigated by using Computational Fluid Dynamics (CFD) method. The numerical simulation focused on the air flow from compressor impeller inlet to volute exit, and the overall performance level and range are predicted. The numerical investigation revealed that the dual volute design could separate the compressor into two operating regions: ''high efficiency'' and ''low efficiency'' regions with different air flow characteristics, and treating these two regions separately with dual diffuser design showed extended stable operating range and improved efficiency by comparing with conventional single volute design. The ''dual sequential volute'' concept also showed the potential to further extend the stable operating range by closing one of the volutes at low air flow rates. Furthermore, by comparing with other alternate designs such as variable diffuser vanes and variable inlet guide vanes, the operation of the dual sequential volute also features relatively simple control and calibration. (author)

Mobile Web Design for Dummies

CERN Document Server

Warner, Janine

2010-01-01

The perfect place to learn how to design Web sites for mobile devices!. With the popularity of Internet access via cell phones and other mobile devices, Web designers now have to consider as many as eight operating systems, several browsers, and a slew of new devices as they plan a new site, a new interface, or a new sub-site. This easy-to-follow friendly book guides you through this brave new world with a clear look at the fundamentals and offers practical techniques and tricks you may not have considered.: Explores all issues to consider in planning a mobile site; Covers the tools needed for

Dual-Stack Single-Radio Communication Architecture for UAV Acting As a Mobile Node to Collect Data in WSNs.

Science.gov (United States)

Sayyed, Ali; de Araújo, Gustavo Medeiros; Bodanese, João Paulo; Becker, Leandro Buss

2015-09-16

The use of mobile nodes to collect data in a Wireless Sensor Network (WSN) has gained special attention over the last years. Some researchers explore the use of Unmanned Aerial Vehicles (UAVs) as mobile node for such data-collection purposes. Analyzing these works, it is apparent that mobile nodes used in such scenarios are typically equipped with at least two different radio interfaces. The present work presents a Dual-Stack Single-Radio Communication Architecture (DSSRCA), which allows a UAV to communicate in a bidirectional manner with a WSN and a Sink node. The proposed architecture was specifically designed to support different network QoS requirements, such as best-effort and more reliable communications, attending both UAV-to-WSN and UAV-to-Sink communications needs. DSSRCA was implemented and tested on a real UAV, as detailed in this paper. This paper also includes a simulation analysis that addresses bandwidth consumption in an environmental monitoring application scenario. It includes an analysis of the data gathering rate that can be achieved considering different UAV flight speeds. Obtained results show the viability of using a single radio transmitter for collecting data from the WSN and forwarding such data to the Sink node.

Designing for mobile interaction

DEFF Research Database (Denmark)

Nazzi, Elena

2009-01-01

The theme of this PhD project is designing for mobile interaction with devices and services, for the accessing, making, and sharing of information, taking into account the dynamic physical and social settings that embrace this interaction. To narrow down this theme, the whole project focuses...... on the exploitation of social interaction --- in particular among senior citizens --- to enhance and support mobile interaction....

Urban pram strolling: a mobilities design perspective

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

2017-01-01

This paper explores a neglected mode of mobility through an ethnographic study of pram strollers in Copenhagen. I illustrate the analytic advantages of mobilities design thinking to explore how pram strolling is shaped by material designs and experienced through affective atmospheres, embodied...... the affordances of surfaces. In this process, I relate pram strolling to questions of urban accessibility issues, and more generally, reflect on the future applications and potentials of mobilities design thinking....

Discrete Globalised Dual Heuristic Dynamic Programming in Control of the Two-Wheeled Mobile Robot

Directory of Open Access Journals (Sweden)

Marcin Szuster

2014-01-01

Full Text Available Network-based control systems have been emerging technologies in the control of nonlinear systems over the past few years. This paper focuses on the implementation of the approximate dynamic programming algorithm in the network-based tracking control system of the two-wheeled mobile robot, Pioneer 2-DX. The proposed discrete tracking control system consists of the globalised dual heuristic dynamic programming algorithm, the PD controller, the supervisory term, and an additional control signal. The structure of the supervisory term derives from the stability analysis realised using the Lyapunov stability theorem. The globalised dual heuristic dynamic programming algorithm consists of two structures: the actor and the critic, realised in a form of neural networks. The actor generates the suboptimal control law, while the critic evaluates the realised control strategy by approximation of value function from the Bellman’s equation. The presented discrete tracking control system works online, the neural networks’ weights adaptation process is realised in every iteration step, and the neural networks preliminary learning procedure is not required. The performance of the proposed control system was verified by a series of computer simulations and experiments realised using the wheeled mobile robot Pioneer 2-DX.

Designing compensator of dual servo system for high precision positioning

International Nuclear Information System (INIS)

Choi, Hyeun Seok; Song, Chi Woo; Han, Chang Soo; Choi, Tae Hoon; Lee, Nak Kyu; Na, Kyung Hwan

2003-01-01

The high precision positioning mechanism is used in various industrial fields. It is used in semiconductor manufacturing line, test instrument, bioengineering, and MEMS and so on. This paper presents a positioning mechanism with dual servo system. Dual servo system consists of a coarse stage and a fine motion stage. The course stage is driven by VCM and the actuator of fine stage is the PZT. The purposes of dual servo system are stability, higher bandwidth, and robustness. Lead compensator is applied to this control system, and is designed by PQ method. Designed compensator can improve property of positioning mechanism

Urban design for mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

2017-01-01

. In this paper, we shall explore the potential for a better understanding of contemporary urban challenges through the cross-disciplinary approach of ‘Mobilities design’. The paper investigates how this notion is based on an understanding of materialities and social action that is framed under the heading...... of ‘material pragmatism’. The paper critically discusses transport versus mobilities and uses the combination of urban design and mobilities not just to argue for a pragmatic approach to urban transformation, but also to illustrate how such a different frame of understanding is better suitable for the ‘kind...

Effect of wheelchair design on wheeled mobility and propulsion efficiency in less-resourced settings

Directory of Open Access Journals (Sweden)

Christopher J. Stanfill

2017-09-01

Conclusion: Use of wheel-mounted accelerometers as a means to test user mobility proved to be a feasible methodology in rural settings. Variability in wheeled mobility data could be decreased with longer acclimatisation periods. The data suggest that push rim users experience an easier transition to a dual-lever propulsion system.

Analysis of Dual Mobility Liner Rim Damage Using Retrieved Components and Cadaver Models.

Science.gov (United States)

Nebergall, Audrey K; Freiberg, Andrew A; Greene, Meridith E; Malchau, Henrik; Muratoglu, Orhun; Rowell, Shannon; Zumbrunn, Thomas; Varadarajan, Kartik M

2016-07-01

The objective of this study was to assess the retentive rim of retrieved dual mobility liners for visible evidence of deformation from femoral neck contact and to use cadaver models to determine if anterior soft tissue impingement could contribute to such deformation. Fifteen surgically retrieved polyethylene liners were assessed for evidence of rim deformation. The average time in vivo was 31.4 months, and all patients were revised for reasons other than intraprosthetic dislocation. Liner interaction with the iliopsoas was studied visually and with fluoroscopy in cadaver specimens using a dual mobility system different than the retrieval study. For fluoroscopic visualization, a metal wire was sutured to the iliopsoas and wires were also embedded into grooves on the outer surface of the liner and the inner head. All retrievals showed evidence of femoral neck contact. The cadaver experiments showed that liner motion was impeded by impingement with the iliopsoas tendon in low flexion angles. When observing the hip during maximum hyperextension, 0°, 15°, and 30° of flexion, there was noticeable tenting of the iliopsoas caused by impingement with the liner. Liner rim deformation resulting from contact with the femoral neck likely begins during early in vivo function. The presence of deformation is indicative of a mechanism inhibiting mobility of the liner. The cadaver studies showed that liner motion could be impeded because of its impingement with the iliopsoas. Such soft tissue impingement may be one mechanism by which liner motion is routinely inhibited, which can result in load transfer from the neck to the rim. Copyright © 2015 Elsevier Inc. All rights reserved.

Epidemic spreading on dual-structure networks with mobile agents

Science.gov (United States)

Yao, Yiyang; Zhou, Yinzuo

2017-02-01

The rapid development of modern society continually transforms the social structure which leads to an increasingly distinct dual structure of higher population density in urban areas and lower density in rural areas. Such structure may induce distinctive spreading behavior of epidemics which does not happen in a single type structure. In this paper, we study the epidemic spreading of mobile agents on dual structure networks based on SIRS model. First, beyond the well known epidemic threshold for generic epidemic model that when the infection rate is below the threshold a pertinent infectious disease will die out, we find the other epidemic threshold which appears when the infection rate of a disease is relatively high. This feature of two thresholds for the SIRS model may lead to the elimination of infectious disease when social network has either high population density or low population density. Interestingly, however, we find that when a high density area is connected to a low density may cause persistent spreading of the infectious disease, even though the same disease will die out when it spreads in each single area. This phenomenon indicates the critical role of the connection between the two areas which could radically change the behavior of spreading dynamics. Our findings, therefore, provide new understanding of epidemiology pertinent to the characteristic modern social structure and have potential to develop controlling strategies accordingly.

THE EVOLUTION OF INTERFACE DESIGN ON MOBILE DEVICES

Directory of Open Access Journals (Sweden)

Atila Isik

2016-09-01

Full Text Available The most typical characteristic of 21. century is the light velocity changing of technology. Dizzily developments in the field of human-robot interaction, mobile communication and education as affect all the fields of life also have an impact on art and design area. Striking increase of interest had been seen for mobile devices which are product of developing technology as tablet and mobile phone. While this increase happening at the present time user interfaces at mobile world and user practices developed as much as dominating design tendency. And became primary impotance for visual designers. This study aims utulizing future options for designers and the oppurtunities and reach a conclusions with examining evolution field of interface design spesific to mobile devices. From Skemorfizm to ordinary design and Google’s recent transition of material design principles were discussed together in this study. And this workout deal with interface design logic of users for working with new computational arificial facts devices as wearable smart objects and devices which able to connect to internet.

Comparison of dual mobility cup and other surgical construts used for three hundred and sixty two first time hip revisions due to recurrent dislocations: five year results from Lithuanian arthroplasty register.

Science.gov (United States)

Stucinskas, Justinas; Kalvaitis, Tomas; Smailys, Alfredas; Robertsson, Otto; Tarasevicius, Sarunas

2018-05-01

Recently, there has been increasing interest in the use of dual mobility systems in the treatment of hip instability. The aim of this study was to investigate the re-revision rate of dual mobility cup compared to different surgical concepts when used for first-time hip revisions due to recurrent dislocations. The data were derived from the Lithuanian Arthroplasty Register. For survival analysis, we used both re-revision for all reasons and for dislocations as an end-point. Cox proportional hazards models were used to analyze the influence of various covariates (age, gender, and implant concept). A total of 1388 revisions were recorded from 2011 to 2015, of which 362 were performed due to recurrent dislocation. Of the revisions, 247 were performed using dual mobility cups, while 115 were performed using a variety of other surgical constructs including constrained acetabular cups, conventional cups, femoral head exchanges, stem exchanges or anti-luxation rings. There were 27 re-revisions of which 15 were for additional dislocations. There were only 2% re-revisions due to dislocation with dual mobility vs 9% when using other surgical constructs. Cox regression adjusting for age and gender showed that in the short-term, dual mobility cup had a lower risk of revision due to dislocation as well as for all reasons compared to the other surgical constructs. In revision of total hip arthroplasties for dislocation, significantly lower short-term re-revision rate was observed for patients revised with dual mobility cup.

Mobility Sensitivity Analysis for LTE-Advanced HetNet Deployments with Dual Connectivity

DEFF Research Database (Denmark)

Barbera, Simone; Gimenez, Lucas Chavarria; Sanchez, Maria Laura Luque

2015-01-01

A mobility performance sensitivity analysis is presented for Dual Connectivity cases where the users can be served simultaneously by a macro and a small cell. The performance is assessed for the 3GPP generic simulation scenario and for two site specific cases, with the aim of comparing the results...... coming from these different scenarios. The site-specific scenarios are based on detailed topography map data and advanced ray-tracing techniques. It is generally found that the first order statistics and overall conclusions are in good alignment for the considered environments. However, there are also...

Dual-Stack Single-Radio Communication Architecture for UAV Acting As a Mobile Node to Collect Data in WSNs

Directory of Open Access Journals (Sweden)

Ali Sayyed

2015-09-01

Full Text Available The use of mobile nodes to collect data in a Wireless Sensor Network (WSN has gained special attention over the last years. Some researchers explore the use of Unmanned Aerial Vehicles (UAVs as mobile node for such data-collection purposes. Analyzing these works, it is apparent that mobile nodes used in such scenarios are typically equipped with at least two different radio interfaces. The present work presents a Dual-Stack Single-Radio Communication Architecture (DSSRCA, which allows a UAV to communicate in a bidirectional manner with a WSN and a Sink node. The proposed architecture was specifically designed to support different network QoS requirements, such as best-effort and more reliable communications, attending both UAV-to-WSN and UAV-to-Sink communications needs. DSSRCA was implemented and tested on a real UAV, as detailed in this paper. This paper also includes a simulation analysis that addresses bandwidth consumption in an environmental monitoring application scenario. It includes an analysis of the data gathering rate that can be achieved considering different UAV flight speeds. Obtained results show the viability of using a single radio transmitter for collecting data from the WSN and forwarding such data to the Sink node.

Conceptual Design of Structural Components of a Dual Cooled Fuel

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyung-Kyu; Lee, Young-Ho; Lee, Kang-Hee; Kim, Jae-Yong; Yoon, Kyung-Ho

2008-01-15

A dual cooled fuel, featured by an internal as well as an external coolant flow passage of a fuel rod, was suggested to enable a large-scaled power-uprate of PWR plant and launched as one of the National Nuclear R and D Projects in 2007. It is necessary to make the dual cooled fuel be compatible with an OPR-1000 system to maximize the economy. Also, the structural components of the dual cooled fuel should be designed to realize their features. To this end, a conceptual design of a spacer grid, outer and center guide tubes, and top and bottom end pieces has been carried out in the project 'Development of Design Technology for Dual Cooled Fuel Structure'. For the spacer grids, it is suggested that springs and dimples are located at or near the cross points of the straps due to a considerably narrowed rod-to-rod gap. Candidate shapes of the grids were also developed and applied for domestic patents. For the outer and center guide tubes, a dual tube like a fuel rod was suggested to make the subchannel areas around the guide tubes be similar to those around the fuel rods of enlarged diameter. It was applied for the domestic patent as well. For the top and bottom end pieces, the shape and pattern have been changed from the conventional ones reflecting the fuel rods' changes. Technical issues and method of resolution for each components were listed up for a basic design works in the following years.

Discrete Globalised Dual Heuristic Dynamic Programming in Control of the Two-Wheeled Mobile Robot

OpenAIRE

Marcin Szuster; Zenon Hendzel

2014-01-01

Network-based control systems have been emerging technologies in the control of nonlinear systems over the past few years. This paper focuses on the implementation of the approximate dynamic programming algorithm in the network-based tracking control system of the two-wheeled mobile robot, Pioneer 2-DX. The proposed discrete tracking control system consists of the globalised dual heuristic dynamic programming algorithm, the PD controller, the supervisory term, and an additional control signal...

[Design of Dual-Beam Spectrometer in Spectrophotometer for Colorimetry].

Science.gov (United States)

Liu, Yi-xuan; Yan, Chang-xiang

2015-07-01

Spectrophotometers for colorimetry are usually composed of two independent and identical spectrometers. In order to reduce the volume of spectrophotometer for colorimetry, a design method of double-beam spectrometer is put forward. A traditional spectrometer is modified so that a new spectrometer can realize the function of double spectrometers, which is especially suitable for portable instruments. One slit is replaced by the double-slit, than two beams of spectrum can be detected. The working principle and design requirement of double-beam spectrometer are described. A spectrometer of portable spectrophotometer is designed by this method. A toroidal imaging mirror is used for the Czerny-Turner double-beam spectrometer in this paper, which can better correct astigmatism, and prevent the dual-beam spectral crosstalk. The results demonstrate that the double-beam spectrometer designed by this method meets the design specifications, with the spectral resolution less than 10 nm, the spectral length of 9.12 mm, and the volume of 57 mm x 54 mm x 23 mm, and without the dual-beam spectral overlap in the detector either. Comparing with a traditional spectrophotometer, the modified spectrophotometer uses a set of double-beam spectrometer instead of two sets of spectrometers, which can greatly reduce the volume. This design method can be specially applied in portable spectrophotometers, also can be widely applied in other double-beam spectrophotometers, which offers a new idea for the design of dual-beam spectrophotometers.

Culture, Interface Design, and Design Methods for Mobile Devices

Science.gov (United States)

Lee, Kun-Pyo

Aesthetic differences and similarities among cultures are obviously one of the very important issues in cultural design. However, ever since products became knowledge-supporting tools, the visible elements of products have become more universal so that the invisible parts of products such as interface and interaction are getting more important. Therefore, the cultural design should be extended to the invisible elements of culture like people's conceptual models beyond material and phenomenal culture. This chapter aims to explain how we address the invisible cultural elements in interface design and design methods by exploring the users' cognitive styles and communication patterns in different cultures. Regarding cultural interface design, we examined users' conceptual models while interacting with mobile phone and website interfaces, and observed cultural difference in performing tasks and viewing patterns, which appeared to agree with cultural cognitive styles known as Holistic thoughts vs. Analytic thoughts. Regarding design methods for culture, we explored how to localize design methods such as focus group interview and generative session for specific cultural groups, and the results of comparative experiments revealed cultural difference on participants' behaviors and performance in each design method and led us to suggest how to conduct them in East Asian culture. Mobile Observation Analyzer and Wi-Pro, user research tools we invented to capture user behaviors and needs especially in their mobile context, were also introduced.

Designing for social play in co-located mobile games

DEFF Research Database (Denmark)

Goddard, William; Garner, Jayden; Jensen, Mads Møller

2016-01-01

In this paper we explore how mobile devices and co-location in mobile contexts contribute social play in game design, addressing the limited understanding of social interactivity in mobile games. Using the Mechanics-Dynamics-Aesthetics (MDA) framework, we code four games illustrating effective use...... of mobile, social, and colocated elements. Subsequently, we analyse and discuss this data to identify generalisability in these games. In our discussion we identify how these findings address game design problems of designing collaborative games. Furthermore, we contribute to theory of designing for social...

Microprocessor controlled dual parameter ADC system with a CAMAC interface

Energy Technology Data Exchange (ETDEWEB)

Perry, D G; Nickell, Jr, J D [Los Alamos Scientific Lab., NM (USA)

1978-09-01

Presented here is the design of a dual parameter ADC system which is controlled by a microprocessor and also interfaced to CAMAC. The system was designed to be mobile in that it may work wherever there is a CAMAC crate. In such cases where the CAMAC system is inoperative, the system may operate in a stand-alone mode.

Adventure Code Camp: Library Mobile Design in the Backcountry

Directory of Open Access Journals (Sweden)

David Ward

2014-09-01

Full Text Available This article presents a case study exploring the use of a student Coding Camp as a bottom-up mobile design process to generate library mobile apps. A code camp sources student programmer talent and ideas for designing software services and features.  This case study reviews process, outcomes, and next steps in mobile web app coding camps. It concludes by offering implications for services design beyond the local camp presented in this study. By understanding how patrons expect to integrate library services and resources into their use of mobile devices, librarians can better design the user experience for this environment.

The Role of Participatory Design in Mobile Application Development

Science.gov (United States)

Hamzah, Almed

2018-03-01

Mobile devices are used by people worldwide. It becomes a common equipment to complete a day-to-day activity. Inside the devices, there are numerous mobile applications that have been built for various needs. Some of these are quite successful while the other are not. The development of successful mobile application faces several challenges. In this research, we want to explore the use of participatory design method in mobile application development. Particularly, the aim of the study is to answer the question whether participatory design method has a place in the realm of mobile application development. We established two sessions of workshop to accommodate the participant to take part in the development process of mobile application. The result shows that participatory design method can determine how the user will deal with the limitations of mobile devices. It helps user to create a particular form of interaction that meets mobile devices characteristics.

Map-based mobile services design, interaction and usability

CERN Document Server

Meng, Liqiu; Winter, Stephan; Popovich, Vasily

2008-01-01

This book reports the newest research and technical achievements on the following theme blocks: Design of mobile map services and its constraints; Typology and usability of mobile map services; Visualization solutions on small displays for time-critical tasks; Mobile map users; Interaction and adaptation in mobile environments; and Applications of map-based mobile services.

Design research into mobile museum mediation

DEFF Research Database (Denmark)

Baggesen, Rikke Haller

2013-01-01

community. 
The PhD research project “Mobile Mediation of Fashion by Museums” explores how aesthetic and ethnographic design methods can be used to develop mobile experiences and articulate museological matters of concern. Building on user perspectives, expressed in response to cultural probes, the project...

Designing algorithm visualization on mobile platform: The proposed guidelines

Science.gov (United States)

Supli, A. A.; Shiratuddin, N.

2017-09-01

This paper entails an ongoing study about the design guidelines of algorithm visualization (AV) on mobile platform, helping students learning data structures and algorithm (DSA) subject effectively. Our previous review indicated that design guidelines of AV on mobile platform are still few. Mostly, previous guidelines of AV are developed for AV on desktop and website platform. In fact, mobile learning has been proved to enhance engagement in learning circumstances, and thus effect student's performance. In addition, the researchers highly recommend including UI design and Interactivity in designing effective AV system. However, the discussions of these two aspects in previous AV design guidelines are not comprehensive. The UI design in this paper describes the arrangement of AV features in mobile environment, whereas interactivity is about the active learning strategy features based on learning experiences (how to engage learners). Thus, this study main objective is to propose design guidelines of AV on mobile platform (AVOMP) that entails comprehensively UI design and interactivity aspects. These guidelines are developed through content analysis and comparative analysis from various related studies. These guidelines are useful for AV designers to help them constructing AVOMP for various topics on DSA.

Mobilities Design

DEFF Research Database (Denmark)

Lanng, Ditte Bendix; Wind, Simon; Jensen, Ole B.

2017-01-01

Mobilities comprise a large part of our world and everyday lives, and the mobilities spaces in which we travel are ubiquitous. Yet, ordinary mobilities spaces – such as parking lots, pedestrian tunnels, and road lay-bys – tend to be criticized as typologies that lack consideration for the people...... who use them and for their wider social, aesthetic, cultural, and ecological agency in the city. This is clearly not an unambiguous characterization. But from it follows an urgency to re-examine unheeded mobilities spaces and extend demands of their agency beyond standards of technical efficiency....... This article draws on the recent “mobilities turn” in social science to support such re-examination of mobilities spaces. In social-scientific mobilities research, mobilities are considered the departure point for understanding the socio-material world in which we live. Mobilities are regarded as far more than...

Designing platform independent mobile apps and services

CERN Document Server

Heckman, Rocky

2016-01-01

This book explains how to help create an innovative and future proof architecture for mobile apps by introducing practical approaches to increase the value and flexibility of their service layers and reduce their delivery time. Designing Platform Independent Mobile Apps and Services begins by describing the mobile computing landscape and previous attempts at cross platform development. Platform independent mobile technologies and development strategies are described in chapter two and three. Communication protocols, details of a recommended five layer architecture, service layers, and the data abstraction layer are also introduced in these chapters. Cross platform languages and multi-client development tools for the User Interface (UI) layer, as well as message processing patterns and message routing of the Service Int rface (SI) layer are explained in chapter four and five. Ways to design the service layer for mobile computing, using Command Query Responsibility Segregation (CQRS) and the Data Abstraction La...

Reliability and Validity of Dual-Task Mobility Assessments in People with Chronic Stroke

Science.gov (United States)

Yang, Lei; He, Chengqi; Pang, Marco Yiu Chung

2016-01-01

Background The ability to perform a cognitive task while walking simultaneously (dual-tasking) is important in real life. However, the psychometric properties of dual-task walking tests have not been well established in stroke. Objective To assess the test-retest reliability, concurrent and known-groups validity of various dual-task walking tests in people with chronic stroke. Design Observational measurement study with a test-retest design. Methods Eighty-eight individuals with chronic stroke participated. The testing protocol involved four walking tasks (walking forward at self-selected and maximal speed, walking backward at self-selected speed, and crossing over obstacles) performed simultaneously with each of the three attention-demanding tasks (verbal fluency, serial 3 subtractions or carrying a cup of water). For each dual-task condition, the time taken to complete the walking task, the correct response rate (CRR) of the cognitive task, and the dual-task effect (DTE) for the walking time and CRR were calculated. Forty-six of the participants were tested twice within 3–4 days to establish test-retest reliability. Results The walking time in various dual-task assessments demonstrated good to excellent reliability [Intraclass correlation coefficient (ICC2,1) = 0.70–0.93; relative minimal detectable change at 95% confidence level (MDC95%) = 29%-45%]. The reliability of the CRR (ICC2,1 = 0.58–0.81) and the DTE in walking time (ICC2,1 = 0.11–0.80) was more varied. The reliability of the DTE in CRR (ICC2,1 = -0.31–0.40) was poor to fair. The walking time and CRR obtained in various dual-task walking tests were moderately to strongly correlated with those of the dual-task Timed-up-and-Go test, thus demonstrating good concurrent validity. None of the tests could discriminate fallers (those who had sustained at least one fall in the past year) from non-fallers. Limitation The results are generalizable to community-dwelling individuals with chronic stroke only

Model tracking dual stochastic controller design under irregular internal noises

International Nuclear Information System (INIS)

Lee, Jong Bok; Heo, Hoon; Cho, Yun Hyun; Ji, Tae Young

2006-01-01

Although many methods about the control of irregular external noise have been introduced and implemented, it is still necessary to design a controller that will be more effective and efficient methods to exclude for various noises. Accumulation of errors due to model tracking, internal noises (thermal noise, shot noise and l/f noise) that come from elements such as resistor, diode and transistor etc. in the circuit system and numerical errors due to digital process often destabilize the system and reduce the system performance. New stochastic controller is adopted to remove those noises using conventional controller simultaneously. Design method of a model tracking dual controller is proposed to improve the stability of system while removing external and internal noises. In the study, design process of the model tracking dual stochastic controller is introduced that improves system performance and guarantees robustness under irregular internal noises which can be created internally. The model tracking dual stochastic controller utilizing F-P-K stochastic control technique developed earlier is implemented to reveal its performance via simulation

Adapting Nielsen's Design Heuristics to Dual Processing for Clinical Decision Support.

Science.gov (United States)

Taft, Teresa; Staes, Catherine; Slager, Stacey; Weir, Charlene

2016-01-01

The study objective was to improve the applicability of Nielson's standard design heuristics for evaluating electronic health record (EHR) alerts and linked ordering support by integrating them with Dual Process theory. Through initial heuristic evaluation and a user study of 7 physicians, usability problems were identified. Through independent mapping of specific usability criteria to support for each of the Dual Cognitive processes (S1 and S2) and deliberation, agreement was reached on mapping criteria. Finally, usability errors from the heuristic and user study were mapped to S1 and S2. Adding a dual process perspective to specific heuristic analysis increases the applicability and relevance of computerized health information design evaluations. This mapping enables designers to measure that their systems are tailored to support attention allocation. System 1 will be supported by improving pattern recognition and saliency, and system 2 through efficiency and control of information access.

Characterizing Mobile/Less-Mobile Porosity and Solute Exchange in Dual-Domain Media Using Tracer Experiments and Electrical Measurements in a Hassler-Type Core Holder

Science.gov (United States)

Falzone, S.; Slater, L. D.; Day-Lewis, F. D.; Parker, B. L.; Keating, K.; Robinson, J.

2017-12-01

Mass transfer is the process by which solute is retained in less-mobile porosity domains, and later released into the mobile porosity domain. This process is often responsible for the slow arrival and gradual release of contaminants and solute tracers. Recent studies have outlined methods using dual-domain mass transfer (DDMT) models for characterizing this phenomenon. These models use the non-linear relationship of bulk (σb) and fluid (σf) conductivity, collected from electrical methods during tracer experiments, to characterize the less-mobile/mobile porosity ratio (β) and the mass-transfer rate coefficient (α). DDMT models use the hysteretic σb-σf relationship observed while solute tracers are injected and then flushed from a sample media. Due to limitations in observing the hysteretic σb-σf relationship, this method has not been used to characterize low permeability samples. We have developed an experimental method for testing porous rock cores that allows us to develop a fundamental understanding of contaminant storage and release in consolidated rock. We test the approach on cores from sedimentary rock sites where mass transfer is expected to occur between hydraulically connected fractures and the adjacent low permeability rock matrix. Our method uses a Hassler-type core holder, designed to apply confining pressure around the outside of a sample core, which hydraulically isolates the sample core, allowing water to be injected into it at increased pressures. The experimental apparatus was also designed to measure σb with spectral induced polarization (SIP) measurements, and σf from a sampling port located at the center of the core. Cores were initially saturated with a solution with high electrical conductivity ( 80000 μS/cm). DI water was then injected into the cores at elevated pressures (>60 psi) and the saturating solution was flushed from the cores, in order to generate flow rates fast enough to capture the non-linear σb-σf relationship

A Learning Activity Design Framework for Supporting Mobile Learning

Directory of Open Access Journals (Sweden)

Jalal Nouri

2016-01-01

Full Text Available This article introduces the Learning Activity Design (LEAD framework for the development and implementation of mobile learning activities in primary schools. The LEAD framework draws on methodological perspectives suggested by design-based research and interaction design in the specific field of technology-enhanced learning (TEL. The LEAD framework is grounded in four design projects conducted over a period of six years. It contributes a new understanding of the intricacies and multifaceted aspects of the design-process characterizing the development and implementation of mobile devices (i.e. smart phones and tablets in curricular activities conducted in Swedish primary schools. This framework is intended to provide both designers and researchers with methodological tools that take account of the pedagogical foundations of technologically-based educational interventions, usability issues related to the interaction with the mobile application developed, multiple data streams generated during the design project, multiple stakeholders involved in the design process and sustainability aspects of the mobile learning activities implemented in the school classroom.

Reliable Ant Colony Routing Algorithm for Dual-Channel Mobile Ad Hoc Networks

Directory of Open Access Journals (Sweden)

YongQiang Li

2018-01-01

Full Text Available For the problem of poor link reliability caused by high-speed dynamic changes and congestion owing to low network bandwidth in ad hoc networks, an ant colony routing algorithm, based on reliable path under dual-channel condition (DSAR, is proposed. First, dual-channel communication mode is used to improve network bandwidth, and a hierarchical network model is proposed to optimize the dual-layer network. Thus, we reduce network congestion and communication delay. Second, a comprehensive reliable path selection strategy is designed, and the reliable path is selected ahead of time to reduce the probability of routing restart. Finally, the ant colony algorithm is used to improve the adaptability of the routing algorithm to changes of network topology. Simulation results show that DSAR improves the reliability of routing, packet delivery, and throughput.

Tunable Design for LTE Mobile-Phones

DEFF Research Database (Denmark)

Barrio, Samantha Caporal Del; Bahramzy, Pevand; Svendsen, Simon

2014-01-01

Antenna volume has become a critical parameter in mobile phone antenna design, as broader bandwidths are required for high connectivity between users. Shrinking the antenna size affects its efficiency, if one does not sacrifice bandwidth. This paper proposes an architecture to address the need...... for small and wide-band antennas. The study focuses on the low-frequencies (700 MHz - 960 MHz) in order to address a tough scenario for small platforms. A tunable design of the front-end and the antennas of the mobile phone is proposed and investigated. Operation is achieved on all low...

Mobile and Social: Ten Best Practices for Designing Mobile Applications

Directory of Open Access Journals (Sweden)

Liviu LICA

2010-01-01

Full Text Available This paper gives ten best practices for designing mobile applications that have social-networking functions. The need for such an approach is given by the rapid growth in impor-tance of both social networks and mobile applications. In order to make it easy to follow where the best practices come from, the paper starts with a look at why social networks are more than just a buzz word and at how the field of mobile applications is evolving. It also shows how and why the two fields go together so well. To further make the point, there is a case study of four interesting mobile applications that are textbooks examples of successful applications. The best practices are based on research done for this article and on the extensive knowledge of the author.

Cost-Effective Location Management for Mobile Agents on the Internet

Directory of Open Access Journals (Sweden)

Chien-Sheng Chen

2015-01-01

Full Text Available Many mobile agent system-related services and applications require interacting with a mobile agent by passing messages. However, an agent’s mobility raises several challenges in delivering messages to a mobile agent accurately. Consisting of tracking and message delivery phases, most mobile agent location management schemes create or receive many update messages and interaction messages to ensure the effectiveness of the schemes. In addition to downgrading the overall performance of a mobile agent location management scheme, excessive transmission of messages increases the network load. The migration locality of a mobile agent and the interaction rate between mobile agents significantly affect the performance of a mobile agent location management scheme with respect to location management cost. This work presents a novel Dual Home based Scheme (DHS that can lower the location management costs in terms of migration locality and interaction rate. While the DHS scheme uniquely adopts dual home location management architecture, a selective update strategy based on that architecture is also designed for cost-effective location management of mobile agents. Moreover, DHS is compared with available schemes based on formulations and simulation experiments from the perspective of location management costs. Simulation results demonstrate that the proposed DHS scheme performs satisfactorily in terms of migration locality and interaction rate.

Are factors related to dual-task performance in people with Parkinson's disease dependent on the type of dual task?

Science.gov (United States)

Strouwen, Carolien; Molenaar, Esther A L M; Keus, Samyra H J; Münks, Liesbeth; Heremans, Elke; Vandenberghe, Wim; Bloem, Bastiaan R; Nieuwboer, Alice

2016-02-01

Impaired dual-task performance significantly impacts upon functional mobility in people with Parkinson's disease (PD). The aim of this study was to identify determinants of dual-task performance in people with PD in three different dual tasks to assess their possible task-dependency. We recruited 121 home-dwelling patients with PD (mean age 65.93 years; mean disease duration 8.67 years) whom we subjected to regular walking (control condition) and to three dual-task conditions: walking combined with a backwards Digit Span task, an auditory Stroop task and a Mobile Phone task. We measured dual-task gait velocity using the GAITRite mat and dual-task reaction times and errors on the concurrent tasks as outcomes. Motor, cognitive and descriptive variables which correlated to dual-task performance (p task gait velocity and executive function, tested by the alternating intake test, was significantly associated with gait velocity during the Digit Span (R(2) = 0.65; p task (R(2) = 0.62; p task. Age was a surplus determinant of gait velocity while using a mobile phone. Single-task gait velocity and executive function as measured by a verbal fluency switching task were independent determinants of dual-task gait performance in people with PD. In contrast to expectation, these factors were the same across different tasks, supporting the robustness of the findings. Future study needs to determine whether these factors predict dual-task abnormalities prospectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Adventure Code Camp: Library Mobile Design in the Backcountry

OpenAIRE

Ward, David; Hahn, James; Mestre, Lori

2014-01-01

This article presents a case study exploring the use of a student Coding Camp as a bottom-up mobile design process to generate library mobile apps. A code camp sources student programmer talent and ideas for designing software services and features.  This case study reviews process, outcomes, and next steps in mobile web app coding camps. It concludes by offering implications for services design beyond the local camp presented in this study. By understanding how patrons expect to integrate li...

Design and analysis of a novel dual-mass MEMS resonant output gyroscope

Directory of Open Access Journals (Sweden)

Yang Gao

2018-02-01

Full Text Available This paper presents the design and analysis of a novel dual-mass microelectromechanical systems (MEMS resonant output gyroscope (ROG, which can effectively eliminate the influence of common-mode disturbance, such as the linear acceleration, on the gyroscope working mode by the design of dual-mass form, as well as on the frequency outputs of the double-ended tuning fork (DETF resonators by the differential arrangement. The concept of the ROG is introduced first. Then the dynamics of the gyroscope and the force-frequency characteristics of the DETF resonator are theoretically analyzed. By establishing the distribution coefficient of force and the reasonable equivalent of the force-frequency characteristics of the DETF resonator, the accurate expression of the device sensitivity is obtained. Based on the analysis results, the leverage mechanism and the DETF resonator are designed in detail. Then the configuration of the gyroscope, a dual-mass structure, is given. Finally, the validity of the analysis and design are verified by numerical simulations.

Mobile Web for Pervasive environments - design webexperiences for multiple mobile devices

DEFF Research Database (Denmark)

Hansen, Thomas Riisgaard

2008-01-01

In this paper we present an architecture for designing web pages that uses multiple mobile and stationary devices to present web content. The architecture extends standard web technology with a number of functions for expressing how web content might migrate and use multiple displays....... The architecture is developed to support desktop applications, but in this paper we describe how the architecture can be extended to mobile devices by using AJAX technology. The paper also presents an implementation and presents a number of applications for mobile devices developed with this framework....

Reconceptualizing Design Research in the Age of Mobile Learning

Science.gov (United States)

Bannan, Brenda; Cook, John; Pachler, Norbert

2016-01-01

The purpose of this paper is to begin to examine how the intersection of mobile learning and design research prompts the reconceptualization of research and design individually as well as their integration appropriate for current, complex learning environments. To fully conceptualize and reconceptualize design research in mobile learning, the…

Mobile first design : using Bootstrap

OpenAIRE

Bhusal, Bipin

2017-01-01

The aim of this project was to design and build a website for a company based in Australia. The business offers remedial massage therapy to its clients. It is a small business which works on the basis of calls and message reservation. The business currently has a temporary website designed with Wix, a cloud-based web development platform. The new website was built with responsive design using Bootstrap. This website was intended for the customers using mobile internet browsers. This design is...

High Efficiency Large-Angle Pancharatnam Phase Deflector Based on Dual Twist Design

Science.gov (United States)

2016-12-16

construction and characterization of a ±40° beam steering device with 90% diffraction efficiency based on our dual-twist design at 633nm wavelength...N. & Escuti, M. J. Achromatic Wollaston prism beam splitter using polarization gratings. Opt. Lett. 41, 4461–4463 (2016). 13. Slussarenko, S., et...High-efficiency large-angle Pancharatnam phase deflector based on dual-twist design Kun Gao1, Colin McGinty1, Harold Payson2, Shaun Berry2, Joseph

A dual model approach to ground water recovery trench design

International Nuclear Information System (INIS)

Clodfelter, C.L.; Crouch, M.S.

1992-01-01

The design of trenches for contaminated ground water recovery must consider several variables. This paper presents a dual-model approach for effectively recovering contaminated ground water migrating toward a trench by advection. The approach involves an analytical model to determine the vertical influence of the trench and a numerical flow model to determine the capture zone within the trench and the surrounding aquifer. The analytical model is utilized by varying trench dimensions and head values to design a trench which meets the remediation criteria. The numerical flow model is utilized to select the type of backfill and location of sumps within the trench. The dual-model approach can be used to design a recovery trench which effectively captures advective migration of contaminants in the vertical and horizontal planes

Design of Mobile Gateway for Implementation of Smart Work System

Directory of Open Access Journals (Sweden)

Sang-Young Oh

2015-01-01

Full Text Available In the development of new technologies based on mobile system, there is a growing interest as a fundamental technology. In particular, in order to realize a mobile office and mobile phones, conferencing remote document is a technique that can realize smart network services solutions with enhanced real-time communication, real-time information sharing, and collaboration. Therefore, in this paper, the design meets the diverse needs of customers and the smart work platform mobile-based fast and conveniently it is trying to develop. For this reason, I have developed a mobile gateway that is based on the communication server construction OPEN API development, management of mobile ID, protocol design, and design of SSL/TLS security tunnel. Also, we developed a smart work platform that you apply this, you are trying to provide information systems environment of mobile company.

Schooling, the underclass and intergenerational mobility: a dual education system dilemma

Directory of Open Access Journals (Sweden)

Tracey Morton McKay

2015-07-01

Full Text Available School education in South Africa has seen much progressive change in the last 20 years. Yet educational outcomes are poor and many argue that a dual education system exists. Those with financial and socio-cultural capital access resourced schools, while poor South Africans are relegated to schools still suffering from apartheid resource neglect. This empirical study of high schools in Alexandra township, a poor black African residential area, demonstrates both the extent of the resource backlog and the consequences thereof. Secondary schools in Alexandra have an inadequate number, and standard, of toilets, libraries, computer facilities and science laboratories. They also have relatively high learner to teacher ratios and poor matriculation success rates. Enrolment in such schools means learners achieve a poor quality matriculation certificate or none at all, thus, trapping these learners into significant disadvantage. Meagre financial resources preclude Alexandra parents from selecting better resourced schools. Thus, for these learners, neither their legal rights with respect to school choice nor their geographical proximity to resourced schools has ensured redress from the apartheid past. The result is that intergenerational class mobility is limited. Thus, the dual nature of South Africa’s education system is creating a vicious cycle of intergenerational poverty where young people cannot improve their living standards despite enrolment in secondary schooling.

Using dual response surfaces to reduce variability in launch vehicle design: A case study

International Nuclear Information System (INIS)

Yeniay, Ozgur; Unal, Resit; Lepsch, Roger A.

2006-01-01

Space transportation system conceptual design is a multidisciplinary process containing considerable element of risk. Uncertainties from one engineering discipline may propagate to another through linking parameters and the final system output may have an accumulation of risk. This may lead to significant deviations from expected performance. An estimate of variability or design risk therefore becomes essential for a robust design. This study utilizes the dual response surface approach to quantify variability in critical performance characteristics during conceptual design phase of a launch vehicle. Using design of experiments methods and disciplinary design analysis codes, dual response surfaces are constructed for the mean and standard deviation to quantify variability in vehicle weight and sizing analysis. Next, an optimum solution is sought to minimize variability subject to a constraint on mean weight. In this application, the dual response surface approach lead to quantifying and minimizing variability without much increase in design effort

Adapting Nielsen’s Design Heuristics to Dual Processing for Clinical Decision Support

Science.gov (United States)

Taft, Teresa; Staes, Catherine; Slager, Stacey; Weir, Charlene

2016-01-01

The study objective was to improve the applicability of Nielson’s standard design heuristics for evaluating electronic health record (EHR) alerts and linked ordering support by integrating them with Dual Process theory. Through initial heuristic evaluation and a user study of 7 physicians, usability problems were identified. Through independent mapping of specific usability criteria to support for each of the Dual Cognitive processes (S1 and S2) and deliberation, agreement was reached on mapping criteria. Finally, usability errors from the heuristic and user study were mapped to S1 and S2. Adding a dual process perspective to specific heuristic analysis increases the applicability and relevance of computerized health information design evaluations. This mapping enables designers to measure that their systems are tailored to support attention allocation. System 1 will be supported by improving pattern recognition and saliency, and system 2 through efficiency and control of information access. PMID:28269915

Evora® chromium-cobalt dual mobility socket: results at a minimum 10 years' follow-up.

Science.gov (United States)

Leclercq, S; Benoit, J Y; de Rosa, J P; Tallier, E; Leteurtre, C; Girardin, P H

2013-12-01

The Evora chromium-cobalt alloy dual mobility socket claims to display a large articulation tribology different from that of stainless steel models, limiting the risk of intraprosthetic dislocation and wear. The present study reports a minimum of 10years' follow-up in a multicenter prospective series of 200 sockets previously reported on at 5years. The use of chromium-cobalt in dual mobility sockets provides a low rate of failure at 10years, especially as regards to osteolysis and intraprosthetic dislocation. Two hundred hydroxyapatite-coated molded chromium-cobalt sockets without titanium interface were implanted without cement in 194 patients with a mean age of 70 years (range, 32-91 years). Clinical results were assessed on Postel Merle d'Aubigné and Harris scores, plain radiographs and survival analysis. At a mean 11 years' follow-up (10-13 years), 56 patients had died and 31 were lost to follow-up. Four underwent surgical revision (3 femoral components, and 1 socket for migration at 9 years with complete disappearance of the hydroxyapatite). A total of 109 implants were analyzable in 107 patients with a mean age of 81 years (55-93 years). At follow-up, the mean Harris score was 90 (75-96) and the PMA score 16.3 (14-18). There were no cases of loosening (except for the case reoperated on at 9 years) and no acetabular radiolucency or cysts. There were 2 cases of non-evolutive femoral radiolucency and 10 of femoral granuloma, involving head size > 22 mm (P<0.0001) and a cemented titanium stem (P=0.004) as risk factors. There were no dislocations in the large or small articulation. Ten-year survival was 99% (95% CI: 97.3%-100%) with socket revision as censorship criterion. The absence of dislocation in both small and large articulations confirmed the efficacy of the dual mobility concept and suggested an advantage for chromium-cobalt sockets in reducing the rate of intraprosthetic dislocation and preventing blockage of the large articulation by a better

Dual-Band Split-Ring Antenna Design for WLAN Applications

OpenAIRE

BAŞARAN, S. Cumhur; ERDEMLİ, Yunus E.

2014-01-01

A dual-band microstrip antenna based on split-ring elements is introduced for WLAN (2.4/5.2 GHz) applications. The proposed split-ring antenna (SRA) has a compact novel design which provides about 2% impedance-bandwidth without a need for additional matching network. Analysis and design of the proposed microstrip antenna is carried out by means of full-wave simulators based on the finite-element method.

When dual identity becomes a liability: identity and political radicalism among migrants.

Science.gov (United States)

Simon, Bernd; Reichert, Frank; Grabow, Olga

2013-03-01

This article examines the role of dual identity in political radicalism among migrants. Dual identity is defined as identification with both one's ethnocultural minority in-group and one's society of residence. We employed a longitudinal research design using members of the two largest migrant groups in Germany (Turkish migrants and Russian migrants) as participants. We reasoned that when dual identity is burdened with incompatibility between component identifications, it may foster controversial or even destructive forms of political mobilization, such as radicalism. Multiple regression analysis controlling for other influences confirmed the hypothesized moderated relationship between dual identification and sympathy for radical action. When accompanied by high, as opposed to low, perceived identity incompatibility, dual identification predicted increases in sympathy for radical action among both Turkish migrants and Russian migrants. The implications for public life in ethnically and culturally heterogeneous societies are discussed.

Implementing a Mobile Social Media Framework for Designing Creative Pedagogies

Directory of Open Access Journals (Sweden)

Thomas Cochrane

2014-08-01

Full Text Available The rise of mobile social media provides unique opportunities for new and creative pedagogies. Pedagogical change requires a catalyst, and we argue that mobile social media can be utilized as such a catalyst. However, the mobile learning literature is dominated by case studies that retrofit traditional pedagogical strategies and pre-existing course activities onto mobile devices and social media. From our experiences of designing and implementing a series of mobile social media projects, the authors have developed a mobile social media framework for creative pedagogies. We illustrate the implementation of our mobile social media framework within the development of a new media minor (an elective set of four courses that explicitly integrates the unique technical and pedagogical affordances of mobile social media, with a focus upon student-generated content and student-determined learning (heutagogy. We argue that our mobile social media framework is potentially transferable to a range of educational contexts, providing a simple design framework for new pedagogies.

A mobile design lab for user-driven innovation

DEFF Research Database (Denmark)

Christiansen, Ellen; Kanstrup, Anne Marie

2007-01-01

The paper presents the history and conceptual foundation for the Mobile Design Lab, ment to support both designers and users in the acts of user-driven innovation. The Mobile Design Lab is based on Vygotsky's theory of tool- and language-mediation, and was created in 2004 to support research...... and teaching of user driven innovation. Being itself an example of user-driven innovation it has taken shape of HCI design research projekcts, in which we have been involved since 2004. The first challenge was to get 'out of the lab', the next to get 'out of the head', and finally we are currently working...

Front end design of smartphone-based mobile health

Science.gov (United States)

Zhang, Changfan; He, Lingsong; Gao, Zhiqiang; Ling, Cong; Du, Jianhao

2015-02-01

Mobile health has been a new trend all over the world with the rapid development of intelligent terminals and mobile internet. It can help patients monitor health in-house and is convenient for doctors to diagnose remotely. Smart-phone-based mobile health has big advantages in cost and data sharing. Front end design of it mainly focuses on two points: one is implementation of medical sensors aimed at measuring kinds of medical signal; another is acquisition of medical signal from sensors to smart phone. In this paper, the above two aspects were both discussed. First, medical sensor implementation was proposed to refer to mature measurement solutions with ECG (electrocardiograph) sensor design taken for example. And integrated chip using can simplify design. Then second, typical data acquisition architecture of smart phones, namely Bluetooth and MIC (microphone)-based architecture, were compared. Bluetooth architecture should be equipped with an acquisition card; MIC design uses sound card of smart phone instead. Smartphone-based virtual instrument app design corresponding to above acquisition architecture was discussed. In experiments, Bluetooth and MIC architecture were used to acquire blood pressure and ECG data respectively. The results showed that Bluetooth design can guarantee high accuracy during the acquisition and transmission process, and MIC design is competitive because of low cost and convenience.

Power optimized variation aware dual-threshold SRAM cell design technique

Directory of Open Access Journals (Sweden)

Aminul Islam

2011-02-01

Full Text Available Aminul Islam1, Mohd Hasan21Department of Electronics and Communication Engineering, Birla Institute of Technology, Mesra, Ranchi, Jharkhand, India; 2Department of Electronics Engineering, Aligarh Muslim University, Aligarh, Uttar Pradesh, IndiaAbstract: Bulk complementary metal-oxide semiconductor (CMOS technology is facing enormous challenges at channel lengths below 45 nm, such as gate tunneling, device mismatch, random dopant fluctuations, and mobility degradation. Although multiple gate transistors and strained silicon devices overcome some of the bulk CMOS problems, it is sensible to look for revolutionary new materials and devices to replace silicon. It is obvious that future technology materials should exhibit higher mobility, better channel electrostatics, scalability, and robustness against process variations. Carbon nanotube-based technology is very promising because it has most of these desired features. There is a need to explore the potential of this emerging technology by designing circuits based on this technology and comparing their performance with that of existing bulk CMOS technology. In this paper, we propose a low-power variation-immune dual-threshold voltage carbon nanotube field effect transistor (CNFET-based seven-transistor (7T static random access memory (SRAM cell. The proposed CNFET-based 7T SRAM cell offers ~1.2× improvement in standby power, ~1.3× improvement in read delay, and ~1.1× improvement in write delay. It offers narrower spread in write access time (1.4× at optimum energy point [OEP] and 1.2× at 1 V. It features 56.3% improvement in static noise margin and 40% improvement in read static noise margin. All the simulation measurements are taken at proposed OEP decided by the optimum results obtained after extensive simulation on HSPICE (high-performance simulation program with integrated circuit emphasis environment.Keywords: carbon nanotube field effect transistor (CNFET, chirality vector, random dopant

Designing mobile learning for children and teenagers living with diabetes

DEFF Research Database (Denmark)

Glasemann, Marie

2016-01-01

In this dissertation, I conceptualise the design of mobile learning for children and teenagers living with type-1 diabetes. The investigation was conducted as an iterative and participatory design-based process. The insights and implications for design and contextual understanding arise through...... reflective design and by involving the target group. The research examined design participation with a focus on the involvement of youths and an understanding of the youths’ perceptions on using mobile technology for learning about diabetes. Central to the research was a concrete design case divided...... into four studies, where a summer camp for youths with diabetes functioned as site for creating a hybrid “third space” for investigating design participation. Based on my empirical research, which focused specifically on the design of mobile games for youths aged 10 to 16 years addressing the carbohydrate...

Winding design of series AC inductor for dual active bridge converters

DEFF Research Database (Denmark)

Shen, Zhan; Wang, Huai; Shen, Yanfeng

2018-01-01

The ac resistance and parasitic capacitance of the inductor are the primary considerations in the winding design for the dual-active bridge converter (DAB). They are dependent of up to four independent structure variables. The interactive restrictions between those variables makes the design diff...

Mobilizing Senior Citizens in Co-design Work

DEFF Research Database (Denmark)

Malmborg, Lone; Werner, Katharina; Gronvall, Erik

2015-01-01

This paper addresses methodological considerations of participation in design for ageing. Based on the notions of design culture, communities of everyday practice and situated elderliness we present accounts from two settings and discuss methodological issues related to mobilizing senior citizens...

Design characteristics of the Sludge Mobilization System

International Nuclear Information System (INIS)

McMahon, C.L.

1990-01-01

Radioactive waste stored in underground tanks at the West Valley Demonstration Project is being processed into low-level waste and solidified in cement. High-level waste also stored underground will be vitrified and solidified into canistered glass logs. To move the waste from where it resides at the Waste Tank Farm to the Vitrification Facility requires equipment to prepare the storage tanks for low-level and high-level waste processing, equipment to mobilize and mix the radioactive sludge into a homogeneous slurry, and equipment to transfer the slurry for vitrification. The design of the Sludge Mobilization System has incorporated the necessary components to effect the preparation and transfer of waste in five operational phases. The first phase of the Sludge Mobilization System, which began in 1987, prepared the waste tanks to process radioactive liquid for delivery to the Cement Solidification System and to support the mobilization equipment. The second phase, beginning in 1991, will wash the sludge that remains after the liquid supernatant is decanted to prepare it for mobilization operations. The third phase will combine the contents of various waste tanks into one tank. The fourth phase will resuspend and mix the contents of the high-level waste tank. The fifth and final phase of the Sludge Mobilization System will entail transferring the waste mixture to the Vitrification Facility for processing into glass logs. Provisions for recycling the waste streams or slurries within the tank farm or for returning process streams to the Waste Tank Farm from the Vitrification Facility are also included in the final phase. This document addresses the Sludge Mobilization System equipment design characteristics in terms of its use in each of the five operational phases listed above

Towards urban mobility designs

DEFF Research Database (Denmark)

Lanng, Ditte Bendix; Harder, Henrik; Jensen, Ole B.

2012-01-01

for the wayfarers who use the site. The data for our work concerns a transit site in the 1970s urban district of Aalborg Øst, Denmark. - We set out by introducing our approach to the site. - Second, we examine the functional layout of the transit site in Aalborg Øst and outline the design challenge which we......Functionalist traffic design aims at a rational organisation of movement from A to B in a segregated and uniform physical environment. Such urban areas have been criticized for being exclusively functional and lacking sensuous and social qualities. Recent research on mobilities challenges the more...... insights on functional urban planning, on embodied practices and experiences of wayfaring, and on concrete small scale design concerns. We emphasise an integrated design agenda for those ordinary transit sites which is concerned with functional issues as well as the quality of life on the ground...

Have You Heard This? Designing Mobile Social Software

Directory of Open Access Journals (Sweden)

Jørn Georg Sannes Knutsen

2010-07-01

Full Text Available ‘Desktop’ social networking services are migrating to mobile devices. Research into the design of mobile social software (MoSoSo, especially its communication design, is emerging. The case we present is from a collaborative, interdisciplinary research project into communicative design innovation concerning these technologies. In focus is the design of what we label the communicative prototype for an interaction and media centred view of social software development. This view is applied to an exploratory design research case that extends an established online social service to the iPhone/iPod platform. The conceptual design in the case is intended to enable the discovery of independent, non-commercial music. The projected service was developed in consultation with a national public service broadcaster. We frame the design and analysis within a sociocultural approach to mediated communication and research by design. We employ mixed methods both in design and in research. We argue that a communicative stance in early concept development offers valuable insights on the ongoing design of social software. The communication expertise of interaction designers is central to this.

Design, Fabrication, and Modeling of a Novel Dual-Axis Control Input PZT Gyroscope

Directory of Open Access Journals (Sweden)

Cheng-Yang Chang

2017-10-01

Full Text Available Conventional gyroscopes are equipped with a single-axis control input, limiting their performance. Although researchers have proposed control algorithms with dual-axis control inputs to improve gyroscope performance, most have verified the control algorithms through numerical simulations because they lacked practical devices with dual-axis control inputs. The aim of this study was to design a piezoelectric gyroscope equipped with a dual-axis control input so that researchers may experimentally verify those control algorithms in future. Designing a piezoelectric gyroscope with a dual-axis control input is more difficult than designing a conventional gyroscope because the control input must be effective over a broad frequency range to compensate for imperfections, and the multiple mode shapes in flexural deformations complicate the relation between flexural deformation and the proof mass position. This study solved these problems by using a lead zirconate titanate (PZT material, introducing additional electrodes for shielding, developing an optimal electrode pattern, and performing calibrations of undesired couplings. The results indicated that the fabricated device could be operated at 5.5±1 kHz to perform dual-axis actuations and position measurements. The calibration of the fabricated device was completed by system identifications of a new dynamic model including gyroscopic motions, electromechanical coupling, mechanical coupling, electrostatic coupling, and capacitive output impedance. Finally, without the assistance of control algorithms, the “open loop sensitivity” of the fabricated gyroscope was 1.82 μV/deg/s with a nonlinearity of 9.5% full-scale output. This sensitivity is comparable with those of other PZT gyroscopes with single-axis control inputs.

Design, Fabrication, and Modeling of a Novel Dual-Axis Control Input PZT Gyroscope.

Science.gov (United States)

Chang, Cheng-Yang; Chen, Tsung-Lin

2017-10-31

Conventional gyroscopes are equipped with a single-axis control input, limiting their performance. Although researchers have proposed control algorithms with dual-axis control inputs to improve gyroscope performance, most have verified the control algorithms through numerical simulations because they lacked practical devices with dual-axis control inputs. The aim of this study was to design a piezoelectric gyroscope equipped with a dual-axis control input so that researchers may experimentally verify those control algorithms in future. Designing a piezoelectric gyroscope with a dual-axis control input is more difficult than designing a conventional gyroscope because the control input must be effective over a broad frequency range to compensate for imperfections, and the multiple mode shapes in flexural deformations complicate the relation between flexural deformation and the proof mass position. This study solved these problems by using a lead zirconate titanate (PZT) material, introducing additional electrodes for shielding, developing an optimal electrode pattern, and performing calibrations of undesired couplings. The results indicated that the fabricated device could be operated at 5.5±1 kHz to perform dual-axis actuations and position measurements. The calibration of the fabricated device was completed by system identifications of a new dynamic model including gyroscopic motions, electromechanical coupling, mechanical coupling, electrostatic coupling, and capacitive output impedance. Finally, without the assistance of control algorithms, the "open loop sensitivity" of the fabricated gyroscope was 1.82 μV/deg/s with a nonlinearity of 9.5% full-scale output. This sensitivity is comparable with those of other PZT gyroscopes with single-axis control inputs.

Designing a diabetes mobile application with social network support.

Science.gov (United States)

Chomutare, Taridzo; Tatara, Naoe; Årsand, Eirik; Hartvigsen, Gunnar

2013-01-01

Although mobile applications and social media have emerged as important facets of the Internet, their role in healthcare is still not well-understood. We present design artefacts, inspired by persuasive technology concepts, from a study of social media as part of a diabetes mHealth application. We used the design science approach for mobile application design, and real-life user testing and focus group meetings to test the application over a 12-week period with 7 participants. Based on the System Usability Score (SUS), the mobile application scored an average of 84.6 (SD=13.2), which represents a fairly high usability score compared to the literature. Regression analysis on the daily blood glucose levels showed significant decreases for some patients, and although the study is not powered, the HbA1c showed a promising trend, and self-efficacy marginally increased. Incorporating persuasive elements such as blood glucose tracking and visualisation, and social media access directly from the mobile application produced promising results that warrant a larger study of behaviour change for people with diabetes.

Stress Analysis for Mobile Hot Cell Design

International Nuclear Information System (INIS)

Muhammad Hannan Bahrin; Anwar Abdul Rahman; Mohd Arif Hamzah

2015-01-01

Prototype and Plant Development Centre (PDC) is developing a Mobile Hot Cell (MHC) to handle and manage Spent High Activity Radioactive Sources (SHARS), such as teletherapy heads and dry irradiators. At present, there are two units of MHC in the world, one in South Africa and the other one in China. Malaysian Mobile MHC is developed by Malaysian Nuclear Agency with the assistance of IAEA expert, based on the design of South Africa and China, but with improved features. Stress analysis has been performed on the design to fulfill the safety requirement in MHC operation. This paper discusses the loading effect analysis from the radiation shielding materials to the MHC wall structure, roof supporting column and window structure. (author)

Design of dual action antibiotics as an approach to search for new promising drugs

International Nuclear Information System (INIS)

Tevyashova, A N; Olsufyeva, E N; Preobrazhenskaya, M N

2015-01-01

The review is devoted to the latest achievements in the design of dual action antibiotics — heterodimeric (chimeric) structures based on antibacterial agents of different classes (fluoroquinolones, anthracyclines, oxazolidines, macrolides and so on). Covalent binding can make the pharmacokinetic characteristics of these molecules more predictable and improve the penetration of each component into the cell. Consequently, not only does the drug efficacy increase owing to inhibition of two targets but also the resistance to one or both antibiotics can be overcome. The theoretical grounds of elaboration, design principles and methods for the synthesis of dual action antibiotics are considered. The structures are classified according to the type of covalent spacer (cleavable or not) connecting the moieties of two agents. Dual action antibiotics with a spacer that can be cleaved in a living cell are considered as dual action prodrugs. Data on the biological action of heterodimeric compounds are presented and structure–activity relationships are analyzed. The bibliography includes 225 references

Design of Dual-Band Two-Branch-Line Couplers with Arbitrary Coupling Coefficients in Bands

Directory of Open Access Journals (Sweden)

I. Prudyus

2014-12-01

Full Text Available A new approach to design dual-band two-branch couplers with arbitrary coupling coefficients at two operating frequency bands is proposed in this article. The method is based on the usage of equivalent subcircuits input reactances of the even-mode and odd-mode excitations. The exact design formulas for three options of the dual-band coupler with different location and number of stubs are received. These formulas permit to obtain the different variants for each structure in order to select the physically realizable solution and can be used in broad range of frequency ratio and power division ratio. For verification, three different dual-band couplers, which are operating at 2.4/3.9 GHz with different coupling coefficients (one with 3/6 dB, and 10/3 dB two others are designed, simulated, fabricated and tested. The measured results are in good agreement with the simulated ones.

Design of dual band FSS by using quadruple L-slot technique

Science.gov (United States)

Fauzi, Noor Azamiah Md; Aziz, Mohamad Zoinol Abidin Abd.; Said, Maizatul Alice Meor; Othman, Mohd Azlishah; Ahmad, Badrul Hisham; Malek, Mohd Fareq Abd

2015-05-01

This paper presents a new design of dual band frequency selective surface (FSS) for band pass microwave transmission application. FSS can be used on energy saving glass to improve the transmission of wireless communication signals through the glass. The microwave signal will be attenuate when propagate throughout the different structure such as building. Therefore, some of the wireless communication system cannot be used in the optimum performance. The aim of this paper is designed, simulated and analyzed the new dual band FSS structure for microwave transmission. This design is based on a quadruple L slot combined with cross slot to produce pass band at 900 MHz and 2.4 GHz. The vertical of pair inverse L slot is used as the band pass for the frequency of 2.4GHz. While, the horizontal of pair inverse L slot is used as the band pass at frequency 900MHz. This design is simulated and analyzed by using Computer Simulation Technology (CST) Microwave Studio (MWS) software. The characteristics of the transmission (S21) and reflection (S11) of the dual band FSS were simulater and analyzed. The bandwidth of the first band is 118.91MHz which covered the frequency range from 833.4MHz until 952.31MHz. Meanwhile, the bandwidth for the second band is 358.84MHz which covered the frequency range from 2.1475GHz until 2.5063GHz. The resonance/center frequency of this design is obtained at 900MHz with a 26.902dB return loss and 2.37GHz with 28.506dB a return loss. This FSS is suitable as microwave filter for GSM900 and WLAN 2.4GHz application.

Design of parallel dual-energy X-ray beam and its performance for security radiography

International Nuclear Information System (INIS)

Kim, Kwang Hyun; Myoung, Sung Min; Chung, Yong Hyun

2011-01-01

A new concept of dual-energy X-ray beam generation and acquisition of dual-energy security radiography is proposed. Erbium (Er) and rhodium (Rh) with a copper filter were positioned in front of X-ray tube to generate low- and high-energy X-ray spectra. Low- and high-energy X-rays were guided to separately enter into two parallel detectors. Monte Carlo code of MCNPX was used to derive an optimum thickness of each filter for improved dual X-ray image quality. It was desired to provide separation ability between organic and inorganic matters for the condition of 140 kVp/0.8 mA as used in the security application. Acquired dual-energy X-ray beams were evaluated by the dual-energy Z-map yielding enhanced performance compared with a commercial dual-energy detector. A collimator for the parallel dual-energy X-ray beam was designed to minimize X-ray beam interference between low- and high-energy parallel beams for 500 mm source-to-detector distance.

Suppression of surface-originated gate lag by a dual-channel AlN/GaN high electron mobility transistor architecture

Science.gov (United States)

Deen, David A.; Storm, David F.; Scott Katzer, D.; Bass, R.; Meyer, David J.

2016-08-01

A dual-channel AlN/GaN high electron mobility transistor (HEMT) architecture is demonstrated that leverages ultra-thin epitaxial layers to suppress surface-related gate lag. Two high-density two-dimensional electron gas (2DEG) channels are utilized in an AlN/GaN/AlN/GaN heterostructure wherein the top 2DEG serves as a quasi-equipotential that screens potential fluctuations resulting from distributed surface and interface states. The bottom channel serves as the transistor's modulated channel. Dual-channel AlN/GaN heterostructures were grown by molecular beam epitaxy on free-standing hydride vapor phase epitaxy GaN substrates. HEMTs fabricated with 300 nm long recessed gates demonstrated a gate lag ratio (GLR) of 0.88 with no degradation in drain current after bias stressed in subthreshold. These structures additionally achieved small signal metrics ft/fmax of 27/46 GHz. These performance results are contrasted with the non-recessed gate dual-channel HEMT with a GLR of 0.74 and 82 mA/mm current collapse with ft/fmax of 48/60 GHz.

Design of a multimedia gateway for mobile devices

Science.gov (United States)

Hens, Raf; Goeminne, Nico; Van Hoecke, Sofie; Verdickt, Tom; Bouve, Thomas; Gielen, Frank; Demeester, Piet

2005-03-01

Although mobile users are currently offered a lot more capabilities on their mobile devices, they still experience some limitations. They can surf the Internet, read their e-mail and receive MMS messages, but they have limited processing power, storage capacity and bandwidth and are limited in their access to peripherals (e.g. printers). We have designed and implemented a multimedia gateway for mobile devices that reduces these limitations. It gives the mobile devices transparent access to high capacity devices connected to the gateway, which is built around a central, modularly extensible server that can run on any PC or home gateway. It manages two sets of modules: one set offering the actual services and another set handling the IP-based wireless interaction with the client applications on the mobile devices. These modules can be added and removed dynamically, offering new services on the fly. Currently services for storage, printing, domotics and playing music are provided. Others can easily be added later on. This paper discusses the architecture and development, the management of modules, the actual services and their benefits. Besides a proprietary implementation, it also looks into OSGi and how both platforms compare to each other, concerning design, architecture, ease of development, functionality, ...

Probabilistic Modeling of Seismic Risk Based Design for a Dual System Structure

OpenAIRE

Sidi, Indra Djati

2017-01-01

The dual system structure concept has gained popularity in the construction of high-rise buildings over the last decades. Meanwhile, earthquake engineering design provisions for buildings have moved from the uniform hazard concept to the uniform risk concept upon recognizing the uncertainties involved in the earthquake resistance of concrete structures. In this study, a probabilistic model for the evaluation of such risk is proposed for a dual system structure consisting of shear walls or cor...

Mobiles for mobility: Participatory design of a 'Happy walker' that stimulates mobility among older people

NARCIS (Netherlands)

Verhoeven, F.; Cremers, A.; Schoone, M.; Dijk, J. van

2016-01-01

Purpose Existing solutions facilitating mobility among older adults mainly focus on supporting physical disabilities. However, solutions are more likely to succeed when current activities and capabilities serve as a starting point. Participatory design is a suitable approach to detect these. We

Conceptual Design of a Mobile Application for Geography Fieldwork Learning

Directory of Open Access Journals (Sweden)

Xiaoling Wang

2017-11-01

Full Text Available The use of mobile applications on smartphones has a vast potential to support learning in the field. However, all learning technologies should be properly designed. To this end, we adopt User-Centered Design (UCD to design a mobile application, called GeoFARA (Geography Fieldwork Augmented Reality Application, for university geography fieldwork. This paper is about the conceptual design of GeoFARA based on its use and user requirements. The paper first establishes a review of selected existing mobile AR applications for outdoor use, in order to identify the innovative aspects and the improvements of GeoFARA. Thereafter, we present the results of use and user requirements derived from (1 an online survey of the current use of tools in undergraduate geography fieldwork, (2 a field experiment in which the use of paper maps and a mobile mapping tool were compared, (3 investigations during a human geography fieldwork, (4 post-fieldwork surveys among undergraduates from two universities, (5 our use case, and (6 a use scenario. Based on these requirements, a conceptual design of GeoFARA is provided in terms of technical specifications, main contents, functionalities, as well as user interactions and interfaces. This conceptual design will guide the future prototype development of GeoFARA.

The design and analysis of AVTMR (all voting triple modular redundancy) and dual-duplex system

International Nuclear Information System (INIS)

Kim, Hyunki; Lee, Hyeuntae; Lee, Keyseo

2005-01-01

In this paper, we design AVTMR (All Voting Triple Modular Redundancy) and dual-duplex system which have a fault-tolerant characteristic, and two systems are compared in the evaluation of RAMS (Reliability, Availability, Maintainability and Safety) and MTTF (Mean Time To Failure). AVTMR system is designed in a triplicated voter technique and dual-duplex system in a comparator, and two systems are based on MC68000. To evaluate system characteristic, Markov modeling method is designed for reliability, availability, safety and MTTF (Mean Time To Failure), and RELEX6.0 tool is used for the calculation of failure rate of electrical components that is based on MILSPEC-217F. In this paper, we can see two systems are more high dependability than a single system, and AVTMR or dual-duplex system can be selected for a specific application system. Especially, because AVTMR and dual-duplex system have high RAMS better than a single system, they can be applied to life critical system such as an airplane and a high-speed railway system

Diabetic Mario: Designing and Evaluating Mobile Games for Diabetes Education.

Science.gov (United States)

Baghaei, Nilufar; Nandigam, David; Casey, John; Direito, Artur; Maddison, Ralph

2016-08-01

Traditionally, diabetes education has relied on written materials, with limited resources available for children with diabetes. Mobile games can be effective and motivating tools for the promotion of children's health. In our earlier work, we proposed a novel approach for designing computer games aimed at educating children with diabetes. In this article, we apply our game design to a mobile Android game (Mario Brothers). We also introduce four heuristics that are specifically designed for evaluating the mobile game, by adapting traditional usability heuristics. Results of a pilot study (n = 12) to evaluate gameplay over 1-week showed that the children found the game engaging and improved their knowledge of healthy diet and lifestyle.

Dual Band Planar Inverted F Antenna (PIFA with L-Shape Configuration

Directory of Open Access Journals (Sweden)

khlouf Munzer Mohamad

2017-01-01

Full Text Available One of the most used antennas in mobile devices is planar inverted F antenna (PIFA. PIFA can be design in dual band frequencies due to the coverage of the wireless service in a mobile device that requires a multiple frequencies. However, the consideration of technical operation has to be combined with an evaluation of the antenna radiation impact on the users. A procedure of PIFA work in GSM (867-960MHz and GSM (1710-1899MHz is done using CST Software. The dual band frequency response is obtained by means of an insertion of an L-shaped slot, which is use to tune the operation frequencies. The prototype of the antenna is fabricated as model by CST Software and evaluated. It is found out that the PIFA antenna has a good efficiency, bandwidth as well as produce a maximum gain for the antenna. A key and innovative research is still underway to broaden performance parameters of the antenna.

Controller Design Of Unicycle Mobile Robot

Directory of Open Access Journals (Sweden)

Mohd Zamzuri Abd Rashid

2012-10-01

Full Text Available ABSTRACT: The ability of unicycle mobile robot to stand and move around using one wheel has attracted a lot of researchers to conduct studies about the system, particularly in the design of the system mechanisms and the control strategies. This paper reports the investigation done on the design of the controller of the unicycle mobile robot system to maintain its stability in both longitudinal and lateral directions. The controller proposed is a Linear Quadratic Controller (LQR type which is based on the linearized model of the system. A thorough simulation studies have been carried out to find out the performance of the LQR controller. The best controller gain, K acquired through the simulation is selected to be implemented and tested in the experimental hardware. Finally, the results obtained from the experimental study are compared to the simulation results to study the controller efficacy. The analysis reveals that the proposed controller design is able to stabilize the unicycle mobile robot.ABSTRAK: Kemampuan robot satu roda untuk berdiri dan bergerak di sekitar telah menarik minat ramai penyelidik untuk mengkaji sistem robot terutamanya didalam bidang rangka mekanikal dan strategi kawalan robot. Kertas kajian ini melaporkan hasil penyelidikan ke atas strategi kawalan robot bagi memastikan sistem robot satu roda dapat distabilkan dari arah sisi dan hadapan. Strategi kawalan yang dicadang, menggunakan teknik kawalan kuadratik sejajar (Linear Quadratic Control yang berdasarkan model robot yang telah dipermudahkan. Kajian simulasi secara terperinci telah dijalankan bagi mengkaji prestasi strategi kawalan yang dicadangkan. Dari kajian simulasi sistem robot, pemilihan faktor konstan, K yang sesuai di dalam strategi kawalan telah dibuat, agar dapat dilaksanakan ke atas sistem robot yang dibangunkan. Keputusan dari kajian simulasi dan tindak balas oleh sistem robot yang dibangunkan akhirnya dibandingkan bagi melihat kesesuaian faktor kostan, K

Design and optimisation of dual-mode heat pump systems using natural fluids

International Nuclear Information System (INIS)

Zhang Wenling; Klemeš, Jiří Jaromír; Kim, Jin-Kuk

2012-01-01

The paper introduces new multi-period modelling and design methodology for dual-mode heat pumps using natural fluids. First, a mathematical model is developed to capture thermodynamic and operating characteristics of dual-mode heat pump systems, subject to different ambient temperatures. The multi-period optimisation framework has been developed to reflect different ambient conditions and its influences on heat pump performance, as well as to determine a system capacity of heat pump which allows systematic economic trade-offs between supplementary heating (or cooling) and operating cost for heat pump. Case study considering three geographical locations with different heating and cooling demands is presented to illustrate the importance of using multi-period optimisation for the design of heat pump systems.

Designing for sustainability - mobility systems based on electrical vehicles

DEFF Research Database (Denmark)

Søndergård, Bent; Hansen, Ole Erik

in interaction with public authorities and transportation companies), configuring the electric car sharing system as an element in an alternative mobility service system, and designing the technical and organizational system The concluding discussion falls into two parts: an assessment of the design process......-design, concerned with design as meta-level processes of regime transformation and the constructive configuration of design spaces. The case study examines an attempt to integrate electric vehicles in the Danish mobility systems. It maps the framework conditions and contemporary (competing) strategies....../projects, but focuses on a specific car-sharing project (‘Cleardrive’), with the objective to examine the early and constitutive stages of the design-process. It is conducted as an intensive study tracing elements of interpretation, interaction and intervention, which have been part of the project formation process...

Requirements' Role in Mobilizing and Enabling Design Conversation

Science.gov (United States)

Bergman, Mark

Requirements play a critical role in a design conversation of systems and products. Product and system design exists at the crossroads of problems, solutions and requirements. Requirements contextualize problems and solutions, pointing the way to feasible outcomes. These are captured with models and detailed specifications. Still, stakeholders need to be able to understand one-another using shared design representations in order to mobilize bias and transform knowledge towards legitimized, desired results. Many modern modeling languages, including UML, as well as detailed, logic-based specifications are beyond the comprehension of key stakeholders. Hence, they inhibit, rather than promote design conversation. Improved design boundary objects (DBO), especially design requirements boundary objects (DRBO), need to be created and refined to improve the communications between principals. Four key features of design boundary objects that improve and promote design conversation are discussed in detail. A systems analysis and design case study is presented which demonstrates these features in action. It describes how a small team of analysts worked with key stakeholders to mobilize and guide a complex system design discussion towards an unexpected, yet desired outcome within a short time frame.

Towards the Development of Mobile App Design Model for Dyscalculia Children in Malaysia

Directory of Open Access Journals (Sweden)

Abd Halim Fiqa Azureen

2018-01-01

Full Text Available Learning disabilities (LD are problem that influence the brain capacity to receive, process, analyse and store information. These processing issues can interfere with learning fundamental abilities, for example, reading (Dyslexia, writing (Dysgraphia and math (Dyscalculia. Fortunately, in today's world technology, we have numerous option techniques for educating and supporting fundamental skills in reading, writing and math such as mobile learning by using mobile app. However, the research in mobile app design model for Dyscalculia children is still scarce: very few studies have focus on how to design and develop appropriate mobile app for Dyscalculia children from the perspective of mobile app designers and developers. The purpose of this paper is to identify the appropriate components that should be included in the mobile app model. Interview sessions were conducted with Dyscalculia practitioners that involved a teacher, paediatric and an educational psychology. This has resulted in identifying 16 components that can be included in the mobile app design model.

Design, Manufacturing, and Testing of a 20/30-GHz Dual-Band Circularly Polarized Reflectarray Antenna

DEFF Research Database (Denmark)

Smith, Thomas Gunst; Gothelf, Ulrich; Kim, Oleksiy S.

2013-01-01

This letter documents the design, manufacturing, and testing of a single-layer dual-band circularly polarized reflectarray antenna for 19.7–20.2 and 29.5–30.0 GHz. The reflectarray is designed using the concentric dual split-loop element and the variable rotation technique that enables full 360......$^{\\circ}$ phase adjustment simultaneously in two separate frequency bands. The elements have been optimized to suppress cross-polar reflection. Thereafter, the element data is included in a design tool that computes the reflectarray layout and the associated radiation patterns. The reflectarray...

Design and field measurement of the BEPC-II interaction region dual-aperture quadrupoles

International Nuclear Information System (INIS)

Yin, Z.S.; Wu, Y.Z.; Zhang, J.F.; Chen, W.; Li, Y.J.; Li, L.; Hou, R.; Yin, B.G.; Sun, X.J.; Ren, F.L.; Wang, F.A.; Chen, F.S.; Yu, C.H.; Chen, C.

2007-01-01

With the Beijing Electron Positron Collider upgrade project (BEPC-II), two dual-aperture septum-style quadrupole magnets are used in the interaction region for the final focusing of the electron and positron beams. The BEPC-II lattice design calls for the same high quality integral quadrupole field and large good field region in both apertures for each magnet. Two-dimensional contour optimization and pole-end chamfer iteration are used to minimize the systematic harmonic errors. Unexpected non-systematic errors induced by the unsymmetrical structure and the manufacturing errors are compensated with the pole-end shimming. Magnet measurements with rotating coils are performed to guide and confirm the magnet design. This paper discusses the design consideration, optimizing procedure and measurement results of these dual-aperture magnets

Design of visible and IR infrared dual-band common-path telescope system

Science.gov (United States)

Guo, YuLin; Yu, Xun; Tao, Yu; Jiang, Xu

2018-01-01

The use of visible and IR infrared dual-band combination can effectively improve the performance of photoelectric detection system,TV and IR system were designed with the common path by the common reflection optical system.A TV/IR infrared common-caliber and common-path system is designed,which can realize the Remote and all-day information.For the 640×512 cooled focal plane array,an infrared middle wave system was presented with a focal length of 600mm F number of 4 field of view(FOV) of 0.38°×0.43°, the system uses optical passive thermal design, has o compact structure and can meet 100% cold shield efficiency,meanwhile it meets the design requirements of lightweight and athermalization. For the 1920×1080 pixels CCD,a visible (TV) system ,which had 500mm focal length, 4F number,was completed.The final optical design along with their modulation transfer function is presented,showing excellent imaging performance in dual-band at the temperature range between -40° and 60°.

Mobile App Design for Teaching and Learning: Educators’ Experiences in an Online Graduate Course

Directory of Open Access Journals (Sweden)

Yu-Chang Hsu

2013-09-01

Full Text Available This research explored how educators with limited programming experiences learned to design mobile apps through peer support and instructor guidance. Educators were positive about the sense of community in this online course. They also considered App Inventor a great web-based visual programming tool for developing useful and fully functioning mobile apps. They had great sense of empowerment through developing unique apps by using App Inventor. They felt their own design work and creative problem solving were inspired by the customized mobile apps shared by peers. The learning activities, including sharing customized apps, providing peer feedback, composing design proposals, and keeping design journals (blogging, complemented each other to support a positive sense of community and form a strong virtual community of learning mobile app design. This study helped reveal the educational value of mobile app design activities and the web-based visual programming tool, and the possibility of teaching/learning mobile app design online. The findings can also encourage educators to explore and experiment on the potential of incorporating these design learning activities in their respective settings, and to develop mobile apps for their diverse needs in teaching and learning.

Value-based design for the elderly: An application in the field of mobility aids.

Science.gov (United States)

Boerema, Simone T; van Velsen, Lex; Vollenbroek-Hutten, Miriam M R; Hermens, Hermie J

2017-01-01

In the aging society, the need for the elderly to remain mobile and independent is higher than ever. However, many aids supporting mobility often fail to target real needs and lack acceptance. The aim of this study is to demonstrate how value-based design can contribute to the design of mobility aids that address real needs and thus, lead to high acceptance. We elicited values, facilitators, and barriers of mobility of older adults via ten in-depth interviews. Next, we held co-creation sessions, resulting in several designs of innovative mobility aids, which were evaluated for acceptance via nine in-depth interviews. The interviews resulted in a myriad of key values, such as "independence from family" and "doing their own groceries." Design sessions resulted in three designs for a wheeled walker. Their acceptance was rather low. Current mobility device users were more eager to accept the designs than non-users. The value-based approach offers designers a close look into the lives of the elderly, thereby opening up a wide range of innovation possibilities that better fit their actual needs. Product service systems seem to be a promising focus for targeting human needs in mobility device design.

Design of a dual linear polarization antenna using split ring resonators at X-band

Science.gov (United States)

Ahmed, Sadiq; Chandra, Madhukar

2017-11-01

Dual linear polarization microstrip antenna configurations are very suitable for high-performance satellites, wireless communication and radar applications. This paper presents a new method to improve the co-cross polarization discrimination (XPD) for dual linear polarized microstrip antennas at 10 GHz. For this, three various configurations of a dual linear polarization antenna utilizing metamaterial unit cells are shown. In the first layout, the microstrip patch antenna is loaded with two pairs of spiral ring resonators, in the second model, a split ring resonator is placed between two microstrip feed lines, and in the third design, a complementary split ring resonators are etched in the ground plane. This work has two primary goals: the first is related to the addition of metamaterial unit cells to the antenna structure which permits compensation for an asymmetric current distribution flow on the microstrip antenna and thus yields a symmetrical current distribution on it. This compensation leads to an important enhancement in the XPD in comparison to a conventional dual linear polarized microstrip patch antenna. The simulation reveals an improvement of 7.9, 8.8, and 4 dB in the E and H planes for the three designs, respectively, in the XPD as compared to the conventional dual linear polarized patch antenna. The second objective of this paper is to present the characteristics and performances of the designs of the spiral ring resonator (S-RR), split ring resonator (SRR), and complementary split ring resonator (CSRR) metamaterial unit cells. The simulations are evaluated using the commercial full-wave simulator, Ansoft High-Frequency Structure Simulator (HFSS).

Design and fabrication of an automatic dual axis solar tracker by ...

African Journals Online (AJOL)

International Journal of Engineering, Science and Technology. Vol. 9, No. 2, 2017, pp. ... All rights reserved. Design and fabrication of an automatic dual axis solar tracker by using LDR ..... It may be like a wiper of the car. Nomenclature. LDR.

Early experience with dual mobility acetabular systems featuring highly cross-linked polyethylene liners for primary hip arthroplasty in patients under fifty five years of age: an international multi-centre preliminary study.

Science.gov (United States)

Epinette, Jean-Alain; Harwin, Steven F; Rowan, Fiachra E; Tracol, Philippe; Mont, Michael A; Chughtai, Morad; Westrich, Geoffrey H

2017-03-01

To evaluate early performance of contemporary dual mobility acetabular systems with second generation annealed highly cross-linked polyethylene for primary hip arthroplasty of patients under 55 years of age. A prospective observational five years study across five centers in Europe and the USA of 321 patients with a mean age of 48.1 years was performed. Patients were assessed for causes of revision, hip instability, intra-prosthetic dissociation, Harris hip score and radiological signs of osteolysis. There were no dislocations and no intra-prosthetic dissociations. Kaplan Meier analysis demonstrated 97.51% survivorship for all cause revision and 99.68% survivorship for acetabular component revision at five years. Mean Harris hip score was 93.6. Two acetabular shells were revised for neck-rim implant impingement without dislocation and ten femoral stems were revised for causes unrelated to dual mobility implants. Contemporary highly cross-linked polyethylene dual mobility systems demonstrate excellent early clinical, radiological, and survivorship results in a cohort of patients that demand high performance from their implants. It is envisaged that DM and second generation annealed HXLPE may reduce THA instability and wear, the two most common causes of THA revision in hip arthroplasty.

Suppression of surface-originated gate lag by a dual-channel AlN/GaN high electron mobility transistor architecture

International Nuclear Information System (INIS)

Deen, David A.; Storm, David F.; Scott Katzer, D.; Bass, R.; Meyer, David J.

2016-01-01

A dual-channel AlN/GaN high electron mobility transistor (HEMT) architecture is demonstrated that leverages ultra-thin epitaxial layers to suppress surface-related gate lag. Two high-density two-dimensional electron gas (2DEG) channels are utilized in an AlN/GaN/AlN/GaN heterostructure wherein the top 2DEG serves as a quasi-equipotential that screens potential fluctuations resulting from distributed surface and interface states. The bottom channel serves as the transistor's modulated channel. Dual-channel AlN/GaN heterostructures were grown by molecular beam epitaxy on free-standing hydride vapor phase epitaxy GaN substrates. HEMTs fabricated with 300 nm long recessed gates demonstrated a gate lag ratio (GLR) of 0.88 with no degradation in drain current after bias stressed in subthreshold. These structures additionally achieved small signal metrics f_t/f_m_a_x of 27/46 GHz. These performance results are contrasted with the non-recessed gate dual-channel HEMT with a GLR of 0.74 and 82 mA/mm current collapse with f_t/f_m_a_x of 48/60 GHz.

Suppression of surface-originated gate lag by a dual-channel AlN/GaN high electron mobility transistor architecture

Energy Technology Data Exchange (ETDEWEB)

Deen, David A., E-mail: david.deen@alumni.nd.edu; Storm, David F.; Scott Katzer, D.; Bass, R.; Meyer, David J. [Naval Research Laboratory, Electronics Science and Technology Division, Washington, DC 20375 (United States)

2016-08-08

A dual-channel AlN/GaN high electron mobility transistor (HEMT) architecture is demonstrated that leverages ultra-thin epitaxial layers to suppress surface-related gate lag. Two high-density two-dimensional electron gas (2DEG) channels are utilized in an AlN/GaN/AlN/GaN heterostructure wherein the top 2DEG serves as a quasi-equipotential that screens potential fluctuations resulting from distributed surface and interface states. The bottom channel serves as the transistor's modulated channel. Dual-channel AlN/GaN heterostructures were grown by molecular beam epitaxy on free-standing hydride vapor phase epitaxy GaN substrates. HEMTs fabricated with 300 nm long recessed gates demonstrated a gate lag ratio (GLR) of 0.88 with no degradation in drain current after bias stressed in subthreshold. These structures additionally achieved small signal metrics f{sub t}/f{sub max} of 27/46 GHz. These performance results are contrasted with the non-recessed gate dual-channel HEMT with a GLR of 0.74 and 82 mA/mm current collapse with f{sub t}/f{sub max} of 48/60 GHz.

Design of mobile shelters for communication purposes

Science.gov (United States)

Lotens, W. A.; Leebeek, H. J.

1982-03-01

A general design for a future generation of shelters, to be used as mobile work places, is presented. Design criteria involve ergonomics, functional suitability, and air conditioning. Electronics, power supply, and personnel get their own compartments. Work space is provided for two people with room for two more. Center of mass and cable connections are considered. Air conditioning requirements are calculated with a computer program. The result is an integrated design, applicable to shelters for several purposes.

Demarcating Mobile Phone Interface Design Guidelines to Expedite Selection

Directory of Open Access Journals (Sweden)

Karen Vera Renaud

2017-12-01

Full Text Available Guidelines are recommended as a tool for informing user interface design. Despite a proliferation of guidelines in the research literature, there is little evidence of their use in industry, nor their influence in academic literature. In this paper, we explore the research literature related to mobile phone design guidelines to find out why this should be so. We commenced by carrying out a scoping literature review of the mobile phone design guideline literature to gain insight into the maturity of the field. The question we wanted to explore was: “Are researchers building on each others’ guidelines, or is the research field still in the foundational stage?” We discovered a poorly structured field, with many researchers proposing new guidelines, but little incremental refinement of extant guidelines. It also became clear that the current reporting of guidelines did not explicitly communicate their multi-dimensionality or deployment context. This leaves designers without a clear way of discriminating between guidelines, and could contribute to the lack of deployment we observed. We conducted a thematic analysis of papers identified by means of a systematic literature review to identify a set of dimensions of mobile phone interface design guidelines. The final dimensions provide a mechanism for differentiating guidelines and expediting choice.

Self-expression and relationship formation in high relational mobility environments: A study of dual users of American and Japanese social networking sites.

Science.gov (United States)

Takemura, Kosuke; Suzuki, Satoko

2017-06-01

This study proposes that self-expression motivation, an aspect of independent/individualistic psychological tendencies, aids in the formation of social relationships when social relationships are open and mobile. In societies characterised by high relational mobility (e.g., North America), which creates market-like competition in social relationships, individuals must express their uniqueness and worthiness to form new social relationships. Self-expression motivation has a relatively weak effect on relationship formation in low relational mobility societies (e.g., Japan), where social relationships are generally predetermined. This hypothesis was examined and supported through a study on dual users of two social networking sites-Facebook and Mixi (the "Facebook of Japan"). As expected, relational mobility was higher on Facebook than on Mixi. Moreover, the association between self-expression motivation and the number of new friends met on Facebook/Mixi was more positive for Facebook than it was for Mixi. The social functionality of independent tendencies is then discussed. © 2015 International Union of Psychological Science.

Strategic Mobility 21: Integrated Tracking System Analysis and Concept Design

National Research Council Canada - National Science Library

Mallon, Lawrence G; Savacool, Edwin

2007-01-01

.... This design document supports the SM21 efforts in developing a dual-use multi-modal node at the Southern California Logistics Airport in Victorville, CA that will be supported by an Integrated Tracking System...

Augmented reality as a design tool for mobile interfaces

DEFF Research Database (Denmark)

Bertelsen, Olav Wedege; Nielsen, Christina

2000-01-01

applications derived from the classification of augmented reality interfaces. The focus on physical interaction with objects of work and with the mobile device provides us with a range of interaction styles, based on e.g. gestures and manipulation of objects. Furthermore, issues of transparency and directness......This paper challenges user interface paradigms for mobile devices, by using the technical classification of augmented reality interfaces as a thinking tool to develop ideas for interaction with mobile devices. The paper presents future work scenarios from a wastewater treatment plant embodying PDA...... are addressed. The future scenarios indicate that the concepts of augmented reality support solving context problems in mobile design....

Designing and remotely testing mobile diabetes video games.

Science.gov (United States)

DeShazo, Jonathan; Harris, Lynne; Turner, Anne; Pratt, Wanda

2010-01-01

We have investigated game design and usability for three mobile phone video games designed to deliver diabetes education. The games were refined using focus groups. Six people with diabetes participated in the first focus group and five in the second. Following the focus groups, we incorporated the new findings into the game design, and then conducted a field test to evaluate the games in the context in which they would actually be used. Data were collected remotely about game usage by eight people with diabetes. The testers averaged 45 seconds per question and answered an average of 50 total nutrition questions each. They self-reported playing the game for 10-30 min, which coincided with the measured metrics of the game. Mobile games may represent a promising new way to engage the user and deliver relevant educational content.

A new method for designing dual foil electron beam forming systems. I. Introduction, concept of the method

Energy Technology Data Exchange (ETDEWEB)

Adrich, Przemysław, E-mail: Przemyslaw.Adrich@ncbj.gov.pl

2016-05-01

In Part I of this work existing methods and problems in dual foil electron beam forming system design are presented. On this basis, a new method of designing these systems is introduced. The motivation behind this work is to eliminate the shortcomings of the existing design methods and improve overall efficiency of the dual foil design process. The existing methods are based on approximate analytical models applied in an unrealistically simplified geometry. Designing a dual foil system with these methods is a rather labor intensive task as corrections to account for the effects not included in the analytical models have to be calculated separately and accounted for in an iterative procedure. To eliminate these drawbacks, the new design method is based entirely on Monte Carlo modeling in a realistic geometry and using physics models that include all relevant processes. In our approach, an optimal configuration of the dual foil system is found by means of a systematic, automatized scan of the system performance in function of parameters of the foils. The new method, while being computationally intensive, minimizes the involvement of the designer and considerably shortens the overall design time. The results are of high quality as all the relevant physics and geometry details are naturally accounted for. To demonstrate the feasibility of practical implementation of the new method, specialized software tools were developed and applied to solve a real life design problem, as described in Part II of this work.

A new method for designing dual foil electron beam forming systems. I. Introduction, concept of the method

International Nuclear Information System (INIS)

Adrich, Przemysław

2016-01-01

In Part I of this work existing methods and problems in dual foil electron beam forming system design are presented. On this basis, a new method of designing these systems is introduced. The motivation behind this work is to eliminate the shortcomings of the existing design methods and improve overall efficiency of the dual foil design process. The existing methods are based on approximate analytical models applied in an unrealistically simplified geometry. Designing a dual foil system with these methods is a rather labor intensive task as corrections to account for the effects not included in the analytical models have to be calculated separately and accounted for in an iterative procedure. To eliminate these drawbacks, the new design method is based entirely on Monte Carlo modeling in a realistic geometry and using physics models that include all relevant processes. In our approach, an optimal configuration of the dual foil system is found by means of a systematic, automatized scan of the system performance in function of parameters of the foils. The new method, while being computationally intensive, minimizes the involvement of the designer and considerably shortens the overall design time. The results are of high quality as all the relevant physics and geometry details are naturally accounted for. To demonstrate the feasibility of practical implementation of the new method, specialized software tools were developed and applied to solve a real life design problem, as described in Part II of this work.

Designing an Intelligent Mobile Learning Tool for Grammar Learning (i-MoL

Directory of Open Access Journals (Sweden)

Munir Shuib

2015-01-01

Full Text Available English is the most important second language in most non-English speaking countries, including Malaysia. A good English proficiency comes from good grasp of grammar. To conquer the problems of low English proficiency among Malaysians, it is important to identify the key motivators that could facilitate the process of grammar learning. In this digital age, technology can play a very important role and mobile technology could be one of it. Thus, this study aims at designing a mobile learning tool, namely the Intelligent Mobile Learning Tool for Grammar Learning (i-MoL to act as the “on-the-go” grammar learning support via mobile phones. i-MoL helps reinforce grammar learning through mobile phone with game-like applications, inquiry-based activities and flashcard-like information. The intelligent part of i-MoL lies in its ability to map the mobile-based grammar learning content to individual’s preferred learning styles based on Felder-Silverman Learning Style Model (FSLSM. The instructional system design through the ADDIE model was used in this study as a systematic approach in designing a novel and comprehensive mobile learning tool for grammar learning. In terms of implications, this study provides insights on how mobile technologies can be utilized to meet the mobility demand among language learners today.

User involvement in the design and evaluation of a smart mobility aid.

Science.gov (United States)

Lacey, G; MacNamara, S

2000-01-01

This paper describes the design and evaluation of an innovative smart mobility aid for the frail visually impaired. The Personal Adaptive Mobility AID (PAM-AID) was developed to address the difficulties in personal mobility of the frail and elderly visually impaired. The paper provides an overview of the PAM-AID research at Trinity College and describes the evolutionary nature of the design process. Because there were no existing systems to guide its development, a series of prototypes was constructed and they were regularly evaluated in the field. This approach views potential users as vital contributing members of the design team and led to rapid and hopefully useful improvements in the design.

Dual throat NaK pump performance evaluation (conceptual design of prototype)

International Nuclear Information System (INIS)

Johnson, J.L.

1972-01-01

An evaluation of the performance of the dual throat NaK pump for the 5 Kwe Reactor TE System is discussed. Performance at nominal operating conditions and at startup conditions is predicted. The basis for selection of this pump design is presented. (U.S.)

3D modeling of dual-gate FinFET.

Science.gov (United States)

Mil'shtein, Samson; Devarakonda, Lalitha; Zanchi, Brian; Palma, John

2012-11-13

The tendency to have better control of the flow of electrons in a channel of field-effect transistors (FETs) did lead to the design of two gates in junction field-effect transistors, field plates in a variety of metal semiconductor field-effect transistors and high electron mobility transistors, and finally a gate wrapping around three sides of a narrow fin-shaped channel in a FinFET. With the enhanced control, performance trends of all FETs are still challenged by carrier mobility dependence on the strengths of the electrical field along the channel. However, in cases when the ratio of FinFET volume to its surface dramatically decreases, one should carefully consider the surface boundary conditions of the device. Moreover, the inherent non-planar nature of a FinFET demands 3D modeling for accurate analysis of the device performance. Using the Silvaco modeling tool with quantization effects, we modeled a physical FinFET described in the work of Hisamoto et al. (IEEE Tran. Elec. Devices 47:12, 2000) in 3D. We compared it with a 2D model of the same device. We demonstrated that 3D modeling produces more accurate results. As 3D modeling results came close to experimental measurements, we made the next step of the study by designing a dual-gate FinFET biased at Vg1 >Vg2. It is shown that the dual-gate FinFET carries higher transconductance than the single-gate device.

Mobile Variable Depth Sampling System Design Study

International Nuclear Information System (INIS)

BOGER, R.M.

2000-01-01

A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study

Mobile Variable Depth Sampling System Design Study

Energy Technology Data Exchange (ETDEWEB)

BOGER, R.M.

2000-08-25

A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study.

Design of YCF-1 mobile γ irradiator

International Nuclear Information System (INIS)

Zhang Hehu; Wang Chuanzhen

1993-01-01

YCF-1 mobile irradiator has been designed by Beijing Institute of Nuclear Engineering of China and has been put into use in Jilin province. It can play an important role in extending irradiation technology in food irradiation, disinfestation, sterilization and quarantine. This paper describes the features and design considerations of a mobile irradiator. The irradiator uses a Cesium-137 source, the design loading capacity of the source is 9.25 PBq (250 kCi). The half-life of Cs-137 is 30.2 years and the source does not need replacing. The dose rate on the surface is 0.0025 mSv/h in accordance with national standards. The shielding of the irradiation room is a steel shell filled with lead. The thickness of lead is 18 cm. The irradiator is installed on a special flat truck. The weight of the irradiator is more than 80 tons. The main components and parts of the irradiator are: source, source racks and hoist, irradiation chamber, storage source chamber, the product's transport system, dose monitoring system, ventilation system and safety interlock system. (author)

X-ray and neutron interrogation of air cargo for mobile applications

Energy Technology Data Exchange (ETDEWEB)

Van Liew, Seth

2015-06-01

A system for scanning break-bulk cargo for mobile applications is presented. This combines a 140 kV multi-view, multi-energy X-ray system with 2.5 MeV neutrons. The system uses dual energy X-ray radiography with neutron radiography. The X-ray and neutron systems were designed to be collocated in a mobile environment. Various materials were interrogated with the intent of distinguishing threat materials such as explosives from similar benign materials. In particular, the identification of threats and bengins with nearly identical effective atomic numbers has been demonstrated.

X-ray and neutron interrogation of air cargo for mobile applications

International Nuclear Information System (INIS)

Van Liew, Seth

2015-01-01

A system for scanning break-bulk cargo for mobile applications is presented. This combines a 140 kV multi-view, multi-energy X-ray system with 2.5 MeV neutrons. The system uses dual energy X-ray radiography with neutron radiography. The X-ray and neutron systems were designed to be collocated in a mobile environment. Various materials were interrogated with the intent of distinguishing threat materials such as explosives from similar benign materials. In particular, the identification of threats and bengins with nearly identical effective atomic numbers has been demonstrated

Design of UWB Monopole Antenna with Dual Notched Bands Using One Modified Electromagnetic-Bandgap Structure

Science.gov (United States)

Xu, Ziqiang

2013-01-01

A modified electromagnetic-bandgap (M-EBG) structure and its application to planar monopole ultra-wideband (UWB) antenna are presented. The proposed M-EBG which comprises two strip patch and an edge-located via can perform dual notched bands. By properly designing and placing strip patch near the feedline, the proposed M-EBG not only possesses a simple structure and compact size but also exhibits good band rejection. Moreover, it is easy to tune the dual notched bands by altering the dimensions of the M-EBG. A demonstration antenna with dual band-notched characteristics is designed and fabricated to validate the proposed method. The results show that the proposed antenna can satisfy the requirements of VSWR WLAN) at 3.5 GHz and 5.5 GHz, respectively. PMID:24170984

Principles of designing mobile robots for nuclear applications: Some Soviet development projects

International Nuclear Information System (INIS)

Adamov, E.O.; Ivanov, V.G.; Meieran, H.B.

1990-01-01

The I.V. Kurchatov Institute of Atomic Energy and the Research and Design Institute of Power Engineering, both designers of nuclear power plant systems and located in Moscow, USSR, have collectively recognized the positive merits of utilizing mobile robots in the nuclear industry. They have given authority to their subsidiary agency CENOTECH to mount an active campaign to program the development of new generations of mobile robots that will support routine and emergency situation operations in the nuclear industry. CENOTECH's rationale for design and performance requirements of mobile robot units to be utilized in the nuclear industry is presented in this paper. A description of design, performance requirements, and operational characteristics of four mobile robots that have been developed at CENOTECH within the past 3 yr is also presented: the 2-tracked KURSOR; the 4 hybrid-wheeled TELER; the 12-wheeled BUGGY with articulated platforms; and the 2-tracked SADKO

Innovative Mobile Platform Developments for Electronic Services Design and Delivery

DEFF Research Database (Denmark)

Scupola, Ada

In the ever-growing world of technology, it is becoming more important to understand the developments of new electronic services and mobile applications. Innovative Mobile Platform Developments for Electronic Services Design, and Delivery is a comprehensive look at all aspects of production manag...

Design, Development, and Evaluation of a Mobile Learning Application for Computing Education

Science.gov (United States)

Oyelere, Solomon Sunday; Suhonen, Jarkko; Wajiga, Greg M.; Sutinen, Erkki

2018-01-01

The study focused on the application of the design science research approach in the course of developing a mobile learning application, MobileEdu, for computing education in the Nigerian higher education context. MobileEdu facilitates the learning of computer science courses on mobile devices. The application supports ubiquitous, collaborative,…

Application of quality by design concept to develop a dual gradient elution stability-indicating method for cloxacillin forced degradation studies using combined mixture-process variable models.

Science.gov (United States)

Zhang, Xia; Hu, Changqin

2017-09-08

Penicillins are typical of complex ionic samples which likely contain large number of degradation-related impurities (DRIs) with different polarities and charge properties. It is often a challenge to develop selective and robust high performance liquid chromatography (HPLC) methods for the efficient separation of all DRIs. In this study, an analytical quality by design (AQbD) approach was proposed for stability-indicating method development of cloxacillin. The structures, retention and UV characteristics rules of penicillins and their impurities were summarized and served as useful prior knowledge. Through quality risk assessment and screen design, 3 critical process parameters (CPPs) were defined, including 2 mixture variables (MVs) and 1 process variable (PV). A combined mixture-process variable (MPV) design was conducted to evaluate the 3 CPPs simultaneously and a response surface methodology (RSM) was used to achieve the optimal experiment parameters. A dual gradient elution was performed to change buffer pH, mobile-phase type and strength simultaneously. The design spaces (DSs) was evaluated using Monte Carlo simulation to give their possibility of meeting the specifications of CQAs. A Plackett-Burman design was performed to test the robustness around the working points and to decide the normal operating ranges (NORs). Finally, validation was performed following International Conference on Harmonisation (ICH) guidelines. To our knowledge, this is the first study of using MPV design and dual gradient elution to develop HPLC methods and improve separations for complex ionic samples. Copyright © 2017 Elsevier B.V. All rights reserved.

Mobile Tourism Guide in the Context of Thai National Parks: The Effects of Mobile Design Qualities in TAM2

Directory of Open Access Journals (Sweden)

Trakulmaykee Numtip

2014-01-01

Full Text Available This study aims to predict the level of international tourists’ intention to use MTG in the context of Thai national parks, and investigates the roles of mobile design qualities (content quality, appearance quality, and interaction quality through perceived usefulness and perceived ease-of-use on intention. The mixed-method via exploratory sequential design is conducted this study. The qualitative approach is started in the first stage then quantitative approach is employed to analyze the large sample size. This study extends the TAM2 with mobile design qualities. The results shows the high level of international tourist’ intention to use MTG. It indicates that the international tourists will intent to the mobile tourism guide (MTG, if the MTG is provided for them. The direct factors of tourists’ intention are perceived usefulness, perceived ease-of-use, mobile content quality and mobile appearance quality. The most direct effect is mobile content quality. The qualities of content and appearance have the positive roles on perceived usefulness, while the qualities of appearance and interaction have the indirect effects through perceived ease-of-use on tourists’ intention. The proposed model provides the body of knowledge in the context of MTG, especially the factors of international tourists’ intention to use MTG.

Combined Dual-Task Gait Training and Aerobic Exercise to Improve Cognition, Mobility, and Vascular Health in Community-Dwelling Older Adults at Risk for Future Cognitive Decline1.

Science.gov (United States)

Gregory, Michael A; Boa Sorte Silva, Narlon C; Gill, Dawn P; McGowan, Cheri L; Liu-Ambrose, Teresa; Shoemaker, J Kevin; Hachinski, Vladimir; Holmes, Jeff; Petrella, Robert J

2017-01-01

This 6-month experimental case series study investigated the effects of a dual-task gait training and aerobic exercise intervention on cognition, mobility, and cardiovascular health in community-dwelling older adults without dementia. Participants exercised 40 min/day, 3 days/week for 26 weeks on a Biodex GaitTrainer2 treadmill. Participants were assessed at baseline (V0), interim (V1: 12-weeks), intervention endpoint (V2: 26-weeks), and study endpoint (V3: 52-weeks). The study outcomes included: cognition [executive function (EF), processing speed, verbal fluency, and memory]; mobility: usual & dual-task gait (speed, step length, and stride time variability); and vascular health: ambulatory blood pressure, carotid arterial compliance, and intima-media thickness (cIMT). Fifty-six participants [age: 70(6) years; 61% female] were included in this study. Significant improvements following the exercise program (V2) were observed in cognition: EF (p = 0.002), processing speed (p coding (p memory [immediate recall (p dual-task gait speed (p = 0.002 and p dual-task gait training and aerobic exercise improved performance on a number of cognitive outcomes, while increasing usual & dual-task gait speed and step length in a sample of older adults without dementia.

Functional Mobility Testing: A Novel Method to Create Suit Design Requirements

Science.gov (United States)

England, Scott A.; Benson, Elizabeth A.; Rajulu, Sudhakar L.

2008-01-01

This study was performed to aide in the creation of design requirements for the next generation of space suits that more accurately describe the level of mobility necessary for a suited crewmember through the use of an innovative methodology utilizing functional mobility. A novel method was utilized involving the collection of kinematic data while 20 subjects (10 male, 10 female) performed pertinent functional tasks that will be required of a suited crewmember during various phases of a lunar mission. These tasks were selected based on relevance and criticality from a larger list of tasks that may be carried out by the crew. Kinematic data was processed through Vicon BodyBuilder software to calculate joint angles for the ankle, knee, hip, torso, shoulder, elbow, and wrist. Maximum functional mobility was consistently lower than maximum isolated mobility. This study suggests that conventional methods for establishing design requirements for human-systems interfaces based on maximal isolated joint capabilities may overestimate the required mobility. Additionally, this method provides a valuable means of evaluating systems created from these requirements by comparing the mobility available in a new spacesuit, or the mobility required to use a new piece of hardware, to this newly established database of functional mobility.

Use of Design Patterns According to Hand Dominance in a Mobile User Interface

Science.gov (United States)

Al-Samarraie, Hosam; Ahmad, Yusof

2016-01-01

User interface (UI) design patterns for mobile applications provide a solution to design problems and can improve the usage experience for users. However, there is a lack of research categorizing the uses of design patterns according to users' hand dominance in a learning-based mobile UI. We classified the main design patterns for mobile…

Design of dual DC motor control system based on DSP

Science.gov (United States)

Shi, Peicheng; Wang, Suo; Xu, Zengwei; Xiao, Ping

2017-08-01

Multi-motor control systems are widely used in actual production and life, such as lifting stages, robots, printing systems. This paper through serial communication between PC and DSP, dual DC motor control system consisting of PC as the host computer, DSP as the lower computer with synchronous PWM speed regulation, commutation and selection functions is designed. It sends digital control instructions with host computer serial debugger to lower computer, to instruct the motor to complete corresponding actions. The hardware and software design of the control system are given, and feasibility and validity of the control system are verified by experiments. The expected design goal is achieved.

Implementation and evaluation of LMS mobile application: scele mobile based on user-centered design

Science.gov (United States)

Banimahendra, R. D.; Santoso, H. B.

2018-03-01

The development of mobile technology is now increasing rapidly, demanding all activities including learning should be done on mobile devices. It shows that the implementation of mobile application as a learning medium needs to be done. This study describes the process of developing and evaluating the Moodle-based mobile Learning Management System (LMS) application called Student Centered e-Learning Environment (SCeLE). This study discusses the process of defining features, implementing features into the application, and evaluating the application. We define the features using user research and literature study, then we implement the application with user-centered design basis, at the last phase we evaluated the application using usability testing and system usability score (SUS). The purpose of this study is to determine the extent to which this application can help the users doing their tasks and provide recommendation for the next research and development.

Design Strategies for Efficient Access to Mobile Device Users via Amazon Mechanical Turk

OpenAIRE

Jacques, Jason; Kristensson, Per Ola

2017-01-01

It is often challenging to access a pool of mobile device users and instruct them to perform an interactive task. Yet such data is often vital to provide design insight at various stages of the design process of a mobile application, service or system. We propose accessing a pool of mobile device users via the microtask market Amazon Mechanical Turk (MTurk). While mobile device users are still a minority on MTurk, they provide unique opportunities for requesters. Not only does catering to mob...

Designing Meaningful Game Experiences for Rehabilitation and Sustainable Mobility Settings

Directory of Open Access Journals (Sweden)

Silvia Gabrielli

2014-03-01

Full Text Available This paper presents the approach followed in two ongoing research projects aimed to designing meaningful game-based experiences to support home rehabilitation, eco-sustainable mobility goals and more in general better daily lifestyles. We first introduce the need for designing meaningful game-based experiences that are well-connected to the relevant non-game settings and can be customized by/for users, then, we show examples of how this approach can be realized in the rehabilitation and sustainable mobility contexts.

Mobile Apps for Reflection in Learning: A Design Research in K-12 Education

Science.gov (United States)

Leinonen, Teemu; Keune, Anna; Veermans, Marjaana; Toikkanen, Tarmo

2016-01-01

This study takes a design-based research approach to explore how applications designed for mobile devices could support reflection in learning in K-12 education. Use of mobile devices is increasing in schools. Most of the educational apps support single-person use of interactive learning materials, simulations and learning games. Apps designed to…

Design of Mobility System for Ground Model of Planetary Exploration Rover

Directory of Open Access Journals (Sweden)

Younkyu Kim

2012-12-01

Full Text Available In recent years, a number of missions have been planned and conducted worldwide on the planets such as Mars, which involves the unmanned robotic exploration with the use of rover. The rover is an important system for unmanned planetary exploration, performing the locomotion and sample collection and analysis at the exploration target of the planetary surface designated by the operator. This study investigates the development of mobility system for the rover ground model necessary to the planetary surface exploration for the benefit of future planetary exploration mission in Korea. First, the requirements for the rover mobility system are summarized and a new mechanism is proposed for a stable performance on rough terrain which consists of the passive suspension system with 8 wheeled double 4-bar linkage (DFBL, followed by the performance evaluation for the mechanism of the mobility system based on the shape design and simulation. The proposed mobility system DFBL was compared with the Rocker-Bogie suspension system of US space agency National Aeronautics and Space Administration and 8 wheeled mobility system CRAB8 developed in Switzerland, using the simulation to demonstrate the superiority with respect to the stability of locomotion. On the basis of the simulation results, a general system configuration was proposed and designed for the rover manufacture.

A mobile sensing system for structural health monitoring: design and validation

International Nuclear Information System (INIS)

Zhu, Dapeng; Yi, Xiaohua; Wang, Yang; Lee, Kok-Meng; Guo, Jiajie

2010-01-01

This paper describes a new approach using mobile sensor networks for structural health monitoring. Compared with static sensors, mobile sensor networks offer flexible system architectures with adaptive spatial resolutions. The paper first describes the design of a mobile sensing node that is capable of maneuvering on structures built with ferromagnetic materials. The mobile sensing node can also attach/detach an accelerometer onto/from the structural surface. The performance of the prototype mobile sensor network has been validated through laboratory experiments. Two mobile sensing nodes are adopted for navigating on a steel portal frame and providing dense acceleration measurements. Transmissibility function analysis is conducted to identify structural damage using data collected by the mobile sensing nodes. This preliminary work is expected to spawn transformative changes in the use of mobile sensors for future structural health monitoring

A mobile sensing system for structural health monitoring: design and validation

Science.gov (United States)

Zhu, Dapeng; Yi, Xiaohua; Wang, Yang; Lee, Kok-Meng; Guo, Jiajie

2010-05-01

This paper describes a new approach using mobile sensor networks for structural health monitoring. Compared with static sensors, mobile sensor networks offer flexible system architectures with adaptive spatial resolutions. The paper first describes the design of a mobile sensing node that is capable of maneuvering on structures built with ferromagnetic materials. The mobile sensing node can also attach/detach an accelerometer onto/from the structural surface. The performance of the prototype mobile sensor network has been validated through laboratory experiments. Two mobile sensing nodes are adopted for navigating on a steel portal frame and providing dense acceleration measurements. Transmissibility function analysis is conducted to identify structural damage using data collected by the mobile sensing nodes. This preliminary work is expected to spawn transformative changes in the use of mobile sensors for future structural health monitoring.

Value-based design for the elderly : An application in the field of mobility aids

NARCIS (Netherlands)

Boerema, Simone Theresa; van Velsen, Lex Stefan; Vollenbroek-Hutten, Miriam Marie Rosé; Hermens, Hermanus J.

2016-01-01

In the aging society, the need for the elderly to remain mobile and independent is higher than ever. However, many aids supporting mobility often fail to target real needs and lack acceptance. The aim of this study is to demonstrate how value-based design can contribute to the design of mobility

Design and Development of Mobile Phone Using Quality Function Deployment

Directory of Open Access Journals (Sweden)

Hamid Ullah

2017-03-01

Full Text Available The paper presents design and development of mobile phone using Quality Function Deployment. Quality Function Deployment is one of the total quality management tools used to convert customers’ needs into design specifications. A market survey is conducted to find out the voice of customer. The Voice of the Customer is converted into customers’ needs. Relative importance is assigned to customers’ needs. A list of technical requirements that could fulfill the customers’ needs is produced. A relationship matrix is developed between the customers’ needs and the technical requirements. The relationship matrix is converted into the House of Quality. Output from the House of Quality is used in concept generation of mobile phone. Concept generation is followed by concept selection. Final improved model of the mobile phone is presented.

Choosing between responsive-design websites versus mobile apps for your mobile behavioral intervention: presenting four case studies.

Science.gov (United States)

Turner-McGrievy, Gabrielle M; Hales, Sarah B; Schoffman, Danielle E; Valafar, Homay; Brazendale, Keith; Weaver, R Glenn; Beets, Michael W; Wirth, Michael D; Shivappa, Nitin; Mandes, Trisha; Hébert, James R; Wilcox, Sara; Hester, Andrew; McGrievy, Matthew J

2017-06-01

Both mobile apps and responsive-design websites (web apps) can be used to deliver mobile health (mHealth) interventions, but it can be difficult to discern which to use in research. The goal of this paper is to present four case studies from behavioral interventions that developed either a mobile app or a web app for research and present an information table to help researchers determine which mobile option would work best for them. Four behavioral intervention case studies (two developed a mobile app, and two developed a web app) presented include time, cost, and expertise. Considerations for adopting a mobile app or a web app-such as time, cost, access to programmers, data collection, security needs, and intervention components- are presented. Future studies will likely integrate both mobile app and web app modalities. The considerations presented here can help guide researchers on which platforms to choose prior to starting an mHealth intervention.

Modelling of Context: Designing Mobile Systems from Domain-Dependent Models

DEFF Research Database (Denmark)

Nielsen, Peter Axel; Stage, Jan

2009-01-01

Modelling of domain-dependent aspects is a key prerequisite for the design of software for mobile systems. Most mobile systems include a more or less advanced model of selected aspects of the domain in which they are used. This paper discusses the creation of such a model and its relevance for te...

Design and performance testing of an ultrasonic linear motor with dual piezoelectric actuators.

Science.gov (United States)

Smithmaitrie, Pruittikorn; Suybangdum, Panumas; Laoratanakul, Pitak; Muensit, Nantakan

2012-05-01

In this work, design and performance testing of an ultrasonic linear motor with dual piezoelectric actuator patches are studied. The motor system consists of a linear stator, a pre-load weight, and two piezoelectric actuator patches. The piezoelectric actuators are bonded with the linear elastic stator at specific locations. The stator generates propagating waves when the piezoelectric actuators are subjected to harmonic excitations. Vibration characteristics of the linear stator are analyzed and compared with finite element and experimental results. The analytical, finite element, and experimental results show agreement. In the experiments, performance of the ultrasonic linear motor is tested. Relationships between velocity and pre-load weight, velocity and applied voltage, driving force and applied voltage, and velocity and driving force are reported. The design of the dual piezoelectric actuators yields a simpler structure with a smaller number of actuators and lower stator stiffness compared with a conventional design of an ultrasonic linear motor with fully laminated piezoelectric actuators.

A high precision dual feedback discrete control system designed for satellite trajectory simulator

Science.gov (United States)

Liu, Ximin; Liu, Liren; Sun, Jianfeng; Xu, Nan

2005-08-01

Cooperating with the free-space laser communication terminals, the satellite trajectory simulator is used to test the acquisition, pointing, tracking and communicating performances of the terminals. So the satellite trajectory simulator plays an important role in terminal ground test and verification. Using the double-prism, Sun etc in our group designed a satellite trajectory simulator. In this paper, a high precision dual feedback discrete control system designed for the simulator is given and a digital fabrication of the simulator is made correspondingly. In the dual feedback discrete control system, Proportional- Integral controller is used in velocity feedback loop and Proportional- Integral- Derivative controller is used in position feedback loop. In the controller design, simplex method is introduced and an improvement to the method is made. According to the transfer function of the control system in Z domain, the digital fabrication of the simulator is given when it is exposed to mechanism error and moment disturbance. Typically, when the mechanism error is 100urad, the residual standard error of pitching angle, azimuth angle, x-coordinate position and y-coordinate position are 0.49urad, 6.12urad, 4.56urad, 4.09urad respectively. When the moment disturbance is 0.1rad, the residual standard error of pitching angle, azimuth angle, x-coordinate position and y-coordinate position are 0.26urad, 0.22urad, 0.16urad, 0.15urad respectively. The digital fabrication results demonstrate that the dual feedback discrete control system designed for the simulator can achieve the anticipated high precision performance.

Design of the Flow Plates for a Dual Cooled Fuel Assembly

International Nuclear Information System (INIS)

Kim, Jae Yong; Yoon, Kyung Ho; Lee, Young Ho; Lee, Kang Hee; Kim, Hyung Kyu

2009-01-01

In a dual cooled fuel assembly, the array and position of fuels are changed from those of a conventional PWR fuel assembly to achieve a power uprating. The flow plate provides flow holes to direct the heated coolant into/out of the fuel assembly and structural intensity to insure that the fuel rod is axially restrained within the spacer grids. So, flow plates of top/bottom end pieces (TEP/BEP) have to be modified into proper shape. Because the flow holes' area of a flow plate affects pressure drop, the flow holes' area must be larger than/equal to that of conventional flow plates. And design criterion of the TEP/BEP says that the flow plate should withstand a 22.241 kN axial load during handling lest a calculated stress intensity should exceed the Condition I allowable stress. In this paper, newly designed flow plates of a TEP/BEP are suggested and stress analysis is conducted to evaluate strength robustness of the flow plates for the dual cooled fuel assembly

Wireless Sensor/Actuator Network Design for Mobile Control Applications

Directory of Open Access Journals (Sweden)

Youxian Sung

2007-10-01

Full Text Available Wireless sensor/actuator networks (WSANs are emerging as a new generationof sensor networks. Serving as the backbone of control applications, WSANs will enablean unprecedented degree of distributed and mobile control. However, the unreliability ofwireless communications and the real-time requirements of control applications raise greatchallenges for WSAN design. With emphasis on the reliability issue, this paper presents anapplication-level design methodology for WSANs in mobile control applications. Thesolution is generic in that it is independent of the underlying platforms, environment,control system models, and controller design. To capture the link quality characteristics interms of packet loss rate, experiments are conducted on a real WSAN system. From theexperimental observations, a simple yet efficient method is proposed to deal withunpredictable packet loss on actuator nodes. Trace-based simulations give promisingresults, which demonstrate the effectiveness of the proposed approach.

The Challenges of Designing Digital Services for Multiple Mobile Platforms

DEFF Research Database (Denmark)

Ghazawneh, Ahmad

2016-01-01

on a multiple case study of three mobile application development firms from Sweden, Denmark and Norway, we synthesize the digital service design taxonomy to understand the challenges faced by third-party developers. Our study identifies a set of challenges in four different levels: user level, platform level...... to tap into and join the digital ecosystem. However, while there is an emerging literature on designing digital services, little empirical evidence exists about challenges faced by third-party developers while designing digital services, and in particular for multiple mobile platforms. Drawing......The value of digital services is increasingly recognized by owners of digital platforms. These services have central role in building and sustaining the business of the digital platform. In order to sustain the design of digital services, owners of digital platforms encourage third-party developers...

Optical design of an athermalised dual field of view step zoom optical system in MWIR

Science.gov (United States)

Kucukcelebi, Doruk

2017-08-01

In this paper, the optical design of an athermalised dual field of view step zoom optical system in MWIR (3.7μm - 4.8μm) is described. The dual field of view infrared optical system is designed based on the principle of passive athermalization method not only to achieve athermal optical system but also to keep the high image quality within the working temperature between -40°C and +60°C. The infrared optical system used in this study had a 320 pixel x 256 pixel resolution, 20μm pixel pitch size cooled MWIR focal plane array detector. In this study, the step zoom mechanism, which has the axial motion due to consisting of a lens group, is considered to simplify mechanical structure. The optical design was based on moving a single lens along the optical axis for changing the optical system's field of view not only to reduce the number of moving parts but also to athermalize for the optical system. The optical design began with an optimization process using paraxial optics when first-order optics parameters are determined. During the optimization process, in order to reduce aberrations, such as coma, astigmatism, spherical and chromatic aberrations, aspherical surfaces were used. As a result, athermalised dual field of view step zoom optical design is proposed and the performance of the design using proposed method was verified by providing the focus shifts, spot diagrams and MTF analyzes' plots.

Mechanical design and force calibration of dual-axis micromechanical probe for friction force microscopy

International Nuclear Information System (INIS)

Fukuzawa, Kenji; Terada, Satoshi; Shikida, Mitsuhiro; Amakawa, Hiroaki; Zhang, Hedong; Mitsuya, Yasunaga

2007-01-01

A dual-axis micromechanical probe that combines a double cantilever and torsion beams is presented. This probe can reduce the mechanical cross-talk between the lateral and vertical force detections. In addition, dual-axis forces can be detected by measuring the dual-axis displacement of the probe end using the optical lever-based method used in conventional friction force microscopes (FFMs). In this paper, the mechanical design of the probe, the details of the fabrication method, FFM performance, and calibration of the friction force are discussed. The mechanical design and the microfabrication method for probes that can provide a force resolution of the order of 1 nN without mechanical cross-talk are presented. Calibration of the lateral force signal is possible by using the relationship between the lateral force and the piezodisplacement at the onset of the probe scanning. The micromechanical probe enables simultaneous and independent detection of atomic and friction forces. This leads to accurate investigation of nanotribological phenomena and visualization of the distribution of the friction properties, which helps the identification of the material properties

Design of Mobile e-Books as a Teaching Tool for Diabetes Education

Science.gov (United States)

Guo, Sophie Huey-Ming

2017-01-01

To facilitate people with diabetes adopting information technologies, a tool of mobile eHealth education for diabetes was described in this paper, presenting the validity of mobile eBook for diabetes educators. This paper describes the design concepts and validity of this mobile eBook for diabetes educators delivering diabetes electronic…

Dual throat engine design for a SSTO launch vehicle

Science.gov (United States)

Obrien, C. J.; Salmon, J. W.

1980-01-01

A propulsion system analysis of a dual fuel, dual throat engine for launch vehicle application was conducted. Basic dual throat engine characterization data are presented to allow vehicle optimization studies to be conducted. A preliminary baseline engine system was defined. Dual throat engine performance, envelope, and weight parametric data were generated over the parametric range of thrust from 890 to 8896 KN (200K to 2M lb-force), chamber pressure from 6.89 million to 34.5 million N/sq m (1000 to 5000 psia) thrust ratio from 1.2 to 5, and a range of mixture ratios for the two tripropellant combinations: LO2/RP-1 + LH2 and LO2/LCH4 + LH2. The results of the study indicate that the dual fuel dual throat engine is a viable single stage to orbit candidate.

Design improvement of permanent magnet flux switching motor with dual rotor structure

Science.gov (United States)

Soomro, H. A.; Sulaiman, E.; Kumar, R.; Rahim, N. S.

2017-08-01

This paper presents design enhancement to reduce permanent magnet (PM) volume for 7S-6P-7S dual rotor permanent magnet flux-switching machines (DRPMFSM) for electric vehicle application. In recent years, Permanent magnet flux switching (PMFS) motor and a new member of brushless permanent magnet machine are prominently used for the electric vehicle. Though, more volume of Rare-Earth Permanent Magnet (REPM) is used to increase the cost and weight of these motors. Thus, to overcome the issue, new configuration of 7S-6P- 7S dual rotor permanent magnet flux-switching machine (DRPMFSM) has been proposed and investigated in this paper. Initially proposed 7S-6P-7S DRPMFSM has been optimized using “deterministic optimization” to reduce the volume of PM and to attain optimum performances. In addition, the performances of initial and optimized DRPMFSM have been compared such that back-emf, cogging torque, average torque, torque and power vs speed performances, losses and efficiency have been analysed by 2D-finite element analysis (FEA) using the JMAG- Designer software ver. 14.1. Consequently, the final design 7S-6P-7S DRPMFSM has achieved the efficiency of 83.91% at reduced PM volume than initial design to confirm the better efficient motor for HEVs applications.

Design of UWB Monopole Antenna with Dual Notched Bands Using One Modified Electromagnetic-Bandgap Structure

Directory of Open Access Journals (Sweden)

Hao Liu

2013-01-01

Full Text Available A modified electromagnetic-bandgap (M-EBG structure and its application to planar monopole ultra-wideband (UWB antenna are presented. The proposed M-EBG which comprises two strip patch and an edge-located via can perform dual notched bands. By properly designing and placing strip patch near the feedline, the proposed M-EBG not only possesses a simple structure and compact size but also exhibits good band rejection. Moreover, it is easy to tune the dual notched bands by altering the dimensions of the M-EBG. A demonstration antenna with dual band-notched characteristics is designed and fabricated to validate the proposed method. The results show that the proposed antenna can satisfy the requirements of VSWR < 2 over UWB 3.1–10.6 GHz, except for the rejected bands of the world interoperability for microwave access (WiMAX and the wireless local area network (WLAN at 3.5 GHz and 5.5 GHz, respectively.

Designing a Mobile Game for Home Computer Users to Protect Against Phishing Attacks

OpenAIRE

Arachchilage, Nalin Asanka Gamagedara; Cole, Melissa

2016-01-01

This research aims to design an educational mobile game for home computer users to prevent from phishing attacks. Phishing is an online identity theft which aims to steal sensitive information such as username, password and online banking details from victims. To prevent this, phishing education needs to be considered. Mobile games could facilitate to embed learning in a natural environment. The paper introduces a mobile game design based on a story which is simplifying and exaggerating real ...

A DBR Framework for Designing Mobile Virtual Reality Learning Environments

Science.gov (United States)

Cochrane, Thomas Donald; Cook, Stuart; Aiello, Stephen; Christie, Duncan; Sinfield, David; Steagall, Marcus; Aguayo, Claudio

2017-01-01

This paper proposes a design based research (DBR) framework for designing mobile virtual reality learning environments. The application of the framework is illustrated by two design-based research projects that aim to develop more authentic educational experiences and learner-centred pedagogies in higher education. The projects highlight the first…

Smart Mobility – Encouraging sustainable mobility behaviour by designing and implementing policies with citizen involvement

Directory of Open Access Journals (Sweden)

Edith Maier

2012-10-01

Full Text Available The paper discusses the theoretical concepts, design considerations and preliminary findings from Smart Mobility, a research project currently being undertaken with the City of St. Gallen. The project aims at designing measures to encourage the increased use of public and non-motorised transport by integrating behavioural economic principles into public policy. The extensive involvement of citizens and their participation in the design of the measures are to support their democratic legitimization and later acceptance. The paper describes the energy policies behind the project and outlines the theoretical framework for integrating behavioural insights into public policy. The strategies envisaged include participatory instruments and methods, especially the use of existing social media channels, capitalizing on social processes and norms to increase the motivation of individuals to use public transport, creating an open innovation space by means of crowdsourcing as well as the proper framing of political communication to achieve changes in mobility patterns.

Design and development of the mobile game based on the J2ME technology

Science.gov (United States)

He, JunHua

2012-01-01

With the continuous improvement of mobile performance, mobile entertainment applications market trend has been increasingly clear, mobile entertainment applications will be after the PC entertainment applications is another important business growth. Through the full analysis of the current mobile entertainment applications market demand and trends, the author has accumulated a lot of theoretical knowledge and practical experience. Rational, using of some new technology for a mobile entertainment games design, and described the development of key technologies required for mobile game an analysis and design of the game, and to achieve a complete game development. Light of the specific mobile game project - "Battle City", detailed the development of a mobile game based on the J2ME platform, the basic steps and the various key elements, focusing on how to use object-oriented thinking on the role of mobile phones in the abstract and Game Animation package, the source code with specific instructions.

Design of dual-mode optical fibres for the FTTH applications

Science.gov (United States)

Chen, Ming-Yang; Li, Yu-Rong; Zhang, Yin; Zhu, Yuan-Feng; Zhang, Yong-Kang; Zhou, Jun

2011-01-01

We present in this article a proposal and design for dual-mode optical fibres for fibre-to-the-home applications. High-order modes in the fibre can be effectively suppressed by the connection of the fibre with standard single-mode optical fibres at the two ends of the fibre. The alignment tolerance at the splicing process is presented. In particular, a low bending loss operation with low splice loss is demonstrated using the proposed technique.

Design of dual-mode optical fibres for the FTTH applications

International Nuclear Information System (INIS)

Chen, Ming-Yang; Li, Yu-Rong; Zhang, Yin; Zhu, Yuan-Feng; Zhang, Yong-Kang; Zhou, Jun

2011-01-01

We present in this article a proposal and design for dual-mode optical fibres for fibre-to-the-home applications. High-order modes in the fibre can be effectively suppressed by the connection of the fibre with standard single-mode optical fibres at the two ends of the fibre. The alignment tolerance at the splicing process is presented. In particular, a low bending loss operation with low splice loss is demonstrated using the proposed technique

Negative differential resistance of InGaAs dual channel transistors

International Nuclear Information System (INIS)

Sugaya, T; Yamane, T; Hori, S; Komori, K; Yonei, K

2006-01-01

We demonstrate a new type of velocity modulation transistor (VMT) with an InGaAs dual channel structure fabricated on an InP (001) substrate. The dual channel structure consists of a high mobility 10 nm In 0.53 Ga 0.47 As quantum well, a 2 nm In 0.52 Al 0.48 As barrier layer, and a low mobility 1 nm In 0.26 Ga 0.74 As quantum well. The VMTs have a negative differential resistance (NDR) effect with a low source-drain voltage of 0.38 V. The NDR characteristics can be clearly seen in the temperature range of 50 to 220 K with a gate voltage of 5 V. The NDR mechanism is thought to be the carrier transfer from the high mobility to the low mobility channels. Three-terminal VMTs are favorable for applications to highfrequency, high-speed, and low-power consumption devices

A finger leaf design for dual layer MLCs

International Nuclear Information System (INIS)

Cui Weijie; Dai Jianrong

2010-01-01

Objective: To introduce a finger leaf design that is applied to dual layer MLCs. Methods: An optimization model was firstly constructed to describe the problem of determining leaf end shapes,and the corresponding problems were then solved by the simplex search method or the simulated annealing technique. Optimal parameters for arc shapes of leaf end projections were obtained, and a comparison was done between optimized MLCs and conventional MLCs in terms of field conformity. The optimization process was based on 634 target fields selected from the patient data base of a treatment planning system. Areas of these fields ranged from 20.0 to 602.7 cm with a mean and its standard deviation of (125.7 ± 0.0) cm 2 . Results: The optimized leaf end shapes projected to the isocenter plane were semicircles. With the finger leaf design, the total area of discrepancy regions between MLC fields and target fields was reduced by 32.3%. Conclusions: The finger leaf design improves the conformity of the MLC shaped fields to the desired target fields. (authors)

Multimodal interaction design in collocated mobile phone use

NARCIS (Netherlands)

El-Ali, A.; Lucero, A.; Aaltonen, V.

2011-01-01

In the context of the Social and Spatial Interactions (SSI) platform, we explore how multimodal interaction design (input and output) can augment and improve the experience of collocated, collaborative activities using mobile phones. Based largely on our prototype evaluations, we reflect on and

High mobility and quantum well transistors design and TCAD simulation

CERN Document Server

Hellings, Geert

2013-01-01

For many decades, the semiconductor industry has miniaturized transistors, delivering increased computing power to consumers at decreased cost. However, mere transistor downsizing does no longer provide the same improvements. One interesting option to further improve transistor characteristics is to use high mobility materials such as germanium and III-V materials. However, transistors have to be redesigned in order to fully benefit from these alternative materials. High Mobility and Quantum Well Transistors: Design and TCAD Simulation investigates planar bulk Germanium pFET technology in chapters 2-4, focusing on both the fabrication of such a technology and on the process and electrical TCAD simulation. Furthermore, this book shows that Quantum Well based transistors can leverage the benefits of these alternative materials, since they confine the charge carriers to the high-mobility material using a heterostructure. The design and fabrication of one particular transistor structure - the SiGe Implant-Free Qu...

Research of Applying Semiotic Theory in Interface Design of Mobile Phone

Institute of Scientific and Technical Information of China (English)

王南

2017-01-01

Mobile phone has become the most important daily device in modern society since 21st century. What's more, it will continue to play a significant role in people 's daily life in the foreseeable near future. An outstanding interface design can not only bring convenience to users, but also strengthen users'experience feelings and give customers more fun and joy. This paper is mainly about how to use semiotic theory in the application of phone interface design. By analyzing basic elements of signal trans?mission as well as"Triplet Theory"in semiotics, and practicing every single element in the design, the value of semiotics applica?tion can be clearly shown. That is, to help interface designer understand customers better and fulfill their needs more accurately and to accomplish fantastic designs in mobile interface.

Analysis and Design of a Wireless Power Transfer System with Dual Active Bridges

Directory of Open Access Journals (Sweden)

Xin Liu

2017-10-01

Full Text Available Nowadays, work on Wireless Power Transfer (WPT systems with dual active bridges is attracting great attention due to their low conduction losses, power regulation, load transformation and reactance compensation. However, in these studies limitations such as overall analysis, design and realization techniques of the system were not considered properly. To address the aforementioned issues, this paper presents a detailed analysis, design and realization of a Series-Series (SS WPT system with dual active bridges, which will improve the overall performance. Three independent Phase Angles (PAs have been analyzed and designed in this study, one PA on the primary side and the other two PAs on the secondary side. This Multiple Degrees of Phase Control (MDPC method can achieve additional reactance compensation, load transformation and output regulation simultaneously. To realize the proposed method in practice, key implementation techniques have been investigated in detail, including additional reactance estimation, mutual inductance estimation, phase detection and synchronization. The feasibility and effectiveness of the proposed system is verified through simulation and experimental results.

The design of a lead-bismuth target system with a dual injection tube

International Nuclear Information System (INIS)

Cho, C.H.; Kim, Y.; Song, T.Y.; Park, W.S.

2005-01-01

A spallation target system is a key component to be developed for an accelerator driven system (ADS). It is known that a 15 ∼ 25 MW spallation target is required for a practical 1000 MWth ADS. The design of a 20 MW spallation target is very challenging because more than 60% of the beam power is deposited as heat in a small volume of the target system. In the present work, a numerical design study was performed to obtain the optimal design parameters for a 20 MW spallation target for a 1000 MW ADS. A dual injection tube was proposed for the reduction of the LBE flow rate at the target channel. The results of the present study show that a 30 cm wide proton beam with a uniform beam distribution should be adopted for the spallation target of a 20 MW power. When the dual LBE injection tube is employed, the LBE flow rate could be reduced by a factor of 4 without reducing the maximum allowable beam current. (authors)

Mobile Probes in Mobile Learning

DEFF Research Database (Denmark)

Ørngreen, Rikke; Blomhøj, Ulla; Duvaa, Uffe

In this paper experiences from using mobile probes in educational design of a mobile learning application is presented. The probing process stems from the cultural probe method, and was influenced by qualitative interview and inquiry approaches. In the project, the mobile phone was not only acting...... as an agent for acquiring empirical data (as the situation in hitherto mobile probe settings) but was also the technological medium for which data should say something about (mobile learning). Consequently, not only the content of the data but also the ways in which data was delivered and handled, provided...... a valuable dimension for investigating mobile use. The data was collected at the same time as design activities took place and the collective data was analysed based on user experience goals and cognitive processes from interaction design and mobile learning. The mobile probe increased the knowledge base...

Interaction and educational design of mobile equipment for crisis management training

DEFF Research Database (Denmark)

Ørngreen, Rikke

2011-01-01

As researchers and designers of crisis management training in mobile learning settings, we need to consider ways in which principles of educational design and interaction design can co-exist, in order to reach a higher quality of the analysis and design process. The paper is an input...

Real-time simulator for designing electron dual scattering foil systems.

Science.gov (United States)

Carver, Robert L; Hogstrom, Kenneth R; Price, Michael J; LeBlanc, Justin D; Pitcher, Garrett M

2014-11-08

The purpose of this work was to develop a user friendly, accurate, real-time com- puter simulator to facilitate the design of dual foil scattering systems for electron beams on radiotherapy accelerators. The simulator allows for a relatively quick, initial design that can be refined and verified with subsequent Monte Carlo (MC) calculations and measurements. The simulator also is a powerful educational tool. The simulator consists of an analytical algorithm for calculating electron fluence and X-ray dose and a graphical user interface (GUI) C++ program. The algorithm predicts electron fluence using Fermi-Eyges multiple Coulomb scattering theory with the reduced Gaussian formalism for scattering powers. The simulator also estimates central-axis and off-axis X-ray dose arising from the dual foil system. Once the geometry of the accelerator is specified, the simulator allows the user to continuously vary primary scattering foil material and thickness, secondary scat- tering foil material and Gaussian shape (thickness and sigma), and beam energy. The off-axis electron relative fluence or total dose profile and central-axis X-ray dose contamination are computed and displayed in real time. The simulator was validated by comparison of off-axis electron relative fluence and X-ray percent dose profiles with those calculated using EGSnrc MC. Over the energy range 7-20 MeV, using present foils on an Elekta radiotherapy accelerator, the simulator was able to reproduce MC profiles to within 2% out to 20 cm from the central axis. The central-axis X-ray percent dose predictions matched measured data to within 0.5%. The calculation time was approximately 100 ms using a single Intel 2.93 GHz processor, which allows for real-time variation of foil geometrical parameters using slider bars. This work demonstrates how the user-friendly GUI and real-time nature of the simulator make it an effective educational tool for gaining a better understanding of the effects that various system

Dual Youla parameterization

DEFF Research Database (Denmark)

Niemann, Hans Henrik

2003-01-01

A different aspect of using the parameterisation of all systems stabilised by a given controller, i.e. the dual Youla parameterisation, is considered. The relation between system change and the dual Youla parameter is derived in explicit form. A number of standard uncertain model descriptions...... are considered and the relation with the dual Youla parameter given. Some applications of the dual Youla parameterisation are considered in connection with the design of controllers and model/performance validation....

The design guidelines of mobile augmented reality for tourism in Malaysia

Science.gov (United States)

Shukri, Saidatul A'isyah Ahmad; Arshad, Haslina; Abidin, Rimaniza Zainal

2017-10-01

Recent data shows that one in every five people in the world owns a Smartphone and spends most of their time on the phone using apps. Visitors prefer this type of portable, convenient, practical and simple technology when travelling, especially geo location-enabled applications such as the GPS. The aim of this paper is to develop design guidelines for Mobile Augmented Reality (MAR) for tourism. From the analysis of existing design guidelines of Mobile Augmented Reality (MAR) for tourism, an application design guidelines are proposed based on Human-computer interaction principle and usability design that would fulfils the user's requirement in a better way. Six design principles were examined in this analysis. The analysis identified eleven suggestions for design principles. These recommendations are offered towards designing principles and developing prototype app for tourist in Malaysia. This paper identifies design principles to reduce cognitive overhead of tourist, learn ability and suitable context for providing content whiles their travel in Malaysia.

Technology-design-manufacturing co-optimization for advanced mobile SoCs

Science.gov (United States)

Yang, Da; Gan, Chock; Chidambaram, P. R.; Nallapadi, Giri; Zhu, John; Song, S. C.; Xu, Jeff; Yeap, Geoffrey

2014-03-01

How to maintain the Moore's Law scaling beyond the 193 immersion resolution limit is the key question semiconductor industry needs to answer in the near future. Process complexity will undoubtfully increase for 14nm node and beyond, which brings both challenges and opportunities for technology development. A vertically integrated design-technologymanufacturing co-optimization flow is desired to better address the complicated issues new process changes bring. In recent years smart mobile wireless devices have been the fastest growing consumer electronics market. Advanced mobile devices such as smartphones are complex systems with the overriding objective of providing the best userexperience value by harnessing all the technology innovations. Most critical system drivers are better system performance/power efficiency, cost effectiveness, and smaller form factors, which, in turns, drive the need of system design and solution with More-than-Moore innovations. Mobile system-on-chips (SoCs) has become the leading driver for semiconductor technology definition and manufacturing. Here we highlight how the co-optimization strategy influenced architecture, device/circuit, process technology and package, in the face of growing process cost/complexity and variability as well as design rule restrictions.

Basket criticality design of a dual purpose cask for VVER 1000 spent fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Rezaeian, Mahdi [Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Kamali, Jamshid [Atomic Energy Organization of Iran (AEOI), Tehran (Iran, Islamic Republic of)

2016-12-15

Dual purpose cask technology is one of the most prominent options for interim storage of spent fuels following their removal from reactors. Criticality safety of the spent fuel assemblies are ensured by design of the basket within these casks. In this study, a set of criticality design calculations of a dual purpose cask for 12 VVER 1000 spent fuel assemblies of Bushehr nuclear power plant were carried out. The basket material of borated stainless steel with 0.5 to 2.5 wt% of boron and Boral (Al-B{sub 4}C) with 1.5 to 40 wt% of boron carbide, were investigated and the minimum required receptacle pitch of the basket was determined. Using the calculated receptacle pitch of the basket, the minimum required diameter of the cavity could be established.

Cognitive-Based Interventions to Improve Mobility: A Systematic Review and Meta-analysis.

Science.gov (United States)

Marusic, Uros; Verghese, Joe; Mahoney, Jeannette R

2018-06-01

A strong relation between cognition and mobility has been identified in aging, supporting a role for enhancement mobility through cognitive-based interventions. However, a critical evaluation of the consistency of treatment effects of cognitive-based interventions is currently lacking. The objective of this study was 2-fold: (1) to review the existing literature on cognitive-based interventions aimed at improving mobility in older adults and (2) to assess the clinical effectiveness of cognitive interventions on gait performance. A systematic review of randomized controlled trials (RCT) of cognitive training interventions for improving simple (normal walking) and complex (dual task walking) gait was conducted in February 2018. Older adults without major cognitive, psychiatric, neurologic, and/or sensory impairments were included. Random effect meta-analyses and a subsequent meta-regression were performed to generate overall cognitive intervention effects on single- and dual-task walking conditions. Ten RCTs met inclusion criteria, with a total of 351 participants included in this meta-analysis. Cognitive training interventions revealed a small effect of intervention on complex gait [effect size (ES) = 0.47, 95% confidence interval (CI) 0.13 to 0.81, P = .007, I 2  = 15.85%], but not simple gait (ES = 0.35, 95% CI -0.01 to 0.71, P = .057, I 2  = 57.32%). Moreover, a meta-regression analysis revealed that intervention duration, training frequency, total number of sessions, and total minutes spent in intervention were not significant predictors of improvement in dual-task walking speed, though there was a suggestive trend toward a negative association between dual-task walking speed improvements and individual training session duration (P = .067). This meta-analysis provides support for the fact that cognitive training interventions can improve mobility-related outcomes, especially during challenging walking conditions requiring higher-order executive

Kinematics, dynamics and control design of 4WIS4WID mobile robots

Directory of Open Access Journals (Sweden)

Ming-Han Lee

2015-01-01

Full Text Available Kinematic and dynamic modelling and corresponding control design of a four-wheel-independent steering and four-wheel-independent driving (4WIS4WID mobile robot are presented in this study. Different from the differential or car-like mobile robot, the 4WIS4WID mobile robot is controlled by four steering and four driving motors, so the control scheme should possess the ability to integrate and manipulate the four independent wheels. A trajectory tracking control scheme is developed for the 4WIS4WID mobile robot, where both non-linear kinematic control and dynamic sliding-mode control are designed. All of the stabilities of the kinematic and dynamic control laws are proved by Lyapunov stability analysis. Finally, the feasibility and validity of the proposed trajectory tracking control scheme are confirmed through computer simulations.

Design and Development of RunForFun Mobile Application

Directory of Open Access Journals (Sweden)

Anci Anthony

2018-01-01

Full Text Available Race run for 5 km or 10 km has been trending recently in many places in Indonesia, especially in Surabaya where there were at least 11 events of race run. The participant's number also increased significantly compared to years before. However, among several race run events, it was seen that some events tended to be replicative and monotone, while among the participants recently were identified the need for increasing the fun factor. RunForFun is a mobile application which designed for participants to reach new experience when participating in a race run event. The mobile application will run on Android OS. The development method of this mobile application would use Reverse Waterfall method. The development of this mobile application uses Ionic Framework which utilizes Cordova as its base to deploy to smartphone devices. Subsequently, RunForRun was tested on 10 participants, and the test shows a significant increase in the fun factor from run race participants.

Stiffness control of balance during dual task and prospective falls in older adults: the MOBILIZE Boston Study.

Science.gov (United States)

Kang, Hyun Gu; Quach, Lien; Li, Wenjun; Lipsitz, Lewis A

2013-09-01

Outdoor fallers differ from indoor fallers substantially in demographics, lifestyle, health condition and physical function. Biomechanical predictors of outdoor falls have not been well characterized. Current validated measures of postural deficits, which describe only the overall postural behavior, are predictive of indoor falls but not outdoor falls. We hypothesized that a model-based description of postural muscle tone and reflexes, particularly during dual tasking, would predict outdoor falls. We tested whether postural stiffness and damping from an inverted pendulum model were predictive of future indoor and outdoor falls among older adults from the MOBILIZE Boston Study. The center of pressure data during standing were obtained from 717 participants aged 77.9±5.3 years. Participants stood barefoot with eyes open for 30s per trial, in two sets of five standing trials. One set included a serial subtractions task. Postural stiffness and damping values were determined from the postural sway data. After the postural measurements, falls were monitored prospectively using a monthly mail-in calendar over 6-36 months. Associations of postural measures with fall rates were determined using negative binomial regressions. After covariate adjustments, postural stiffness (p=0.02-0.05) and damping (p=0.007-0.1) were associated with lower outdoor falls risk, but not with indoor falls. Results were invariant by direction (anteroposterior versus mediolateral) or by condition (quiet standing versus dual task). Outdoor fall risk may be tied to postural control more so than indoor falls. Dual tasking is likely related to fall risk among older and sicker older adults, but not those relatively healthy. Copyright © 2013 Elsevier B.V. All rights reserved.

Design and development of mobile Email system based on brew and IMAP4

International Nuclear Information System (INIS)

Chen Liangchen; Liu Shuzhen; Yan Xiaofei; Sun Gongxing

2007-01-01

In order to achieve IMAP4 support agreement in the mobile e-mail client application on the smart phone, using the Qualcomm introduced wireless devices designed for the BREW platform. Research on the BREW platform mobile and IMAP4 protocol, design and implement the 3G technology standard smart phone e-mail client based on the BREW platform. (authors)

A graphics approach in the design of the dual air density Explorer satellites

Science.gov (United States)

Mcdougal, D. S.

1975-01-01

A computer program was developed to generate a graphics display of the Dual Air Density (DAD) Explorer satellites which aids in the engineering and scientific design. The program displays a two-dimensional view of both spacecraft and their surface features from any direction. The graphics have been an indispensable tool in the design, analysis, and understanding of the critical locations of the various surface features for both satellites.

Weighting Strategies for Combining Data from Dual-Frame Telephone Surveys: Emerging Evidence from Australia

Directory of Open Access Journals (Sweden)

Baffour Bernard

2016-09-01

Full Text Available Until quite recently, telephone surveys have typically relied on landline telephone numbers. However, with the increasing popularity and affordability of mobile phones, there has been a surge in households that do not have landline connections. Additionally, there has been a decline in the response rates and population coverage of landline telephone surveys, creating a challenge to collecting representative social data. Dual-frame telephone surveys that use both landline and mobile phone sampling frames can overcome the incompleteness of landline-only telephone sampling. However, surveying mobile phone users introduces new complexities in sampling, nonresponse measurement and statistical weighting. This article examines these issues and illustrates the consequences of failing to include mobile-phone-only users in telephone surveys using data from Australia. Results show that there are significant differences in estimates of populations’ characteristics when using information solely from the landline or mobile telephone sample. These biases in the population estimates are significantly reduced when data from the mobile and landline samples are combined and appropriate dual-frame survey estimators are used. The optimal choice of a dual-frame estimation strategy depends on the availability of good-quality information that can account for the differential patterns of nonresponse by frame.

A dual-mode mobile phone microscope using the onboard camera flash and ambient light.

Science.gov (United States)

Orth, A; Wilson, E R; Thompson, J G; Gibson, B C

2018-02-19

Mobile phone microscopes are a natural platform for point-of-care imaging, but current solutions require an externally powered illumination source, thereby adding bulk and cost. We present a mobile phone microscope that uses the internal flash or sunlight as the illumination source, thereby reducing complexity whilst maintaining functionality and performance. The microscope is capable of both brightfield and darkfield imaging modes, enabling microscopic visualisation of samples ranging from plant to mammalian cells. We describe the microscope design principles, assembly process, and demonstrate its imaging capabilities through the visualisation of unlabelled cell nuclei to observing the motility of cattle sperm and zooplankton.

The Design of a Permanent Magnet In-Wheel Motor with Dual-Stator and Dual-Field-Excitation Used in Electric Vehicles

Directory of Open Access Journals (Sweden)

Peng Gao

2018-02-01

Full Text Available The in-wheel motor has received more attention owing to its simple structure, high transmission efficiency, flexible control, and easy integration design. It is difficult to achieve high performance with conventional motors due to their dimensions and structure. This paper presents a new dual-stator and dual-field-excitation permanent-magnet in-wheel motor (DDPMIM that is based on the structure of the conventional in-wheel motor and the structure of both the radial and axial magnetic field motor. The finite element analysis (FEA model of the DDPMIM is established and compared with that of the conventional in-wheel motor. The results show that the DDPMIM achieves a higher output torque at low speeds and that the flux-weakening control strategy is not needed in the full speed range.

Contact of dual mobility implants: effects of cup wear and inclination.

Science.gov (United States)

Uddin, M S

2015-01-01

Cup wear and inclination on the pelvic bone are significant factors, which change the contact of the articulating surfaces, thus, impacting the long-term performance of hip implants. This paper presents a finite element (FE) analysis of the contact of the dual mobility implants under the influence of cup wear and inclination. A 3D FE model of the implant was developed with the application of equivalent physiological loading and boundary conditions. Effects of cup inclination angle ranging from 45° to 60° and the wear depth ranging from 0 to 2.46 mm equivalent to up to 30 years of the implant's life on the contact pressure and von Mises stress were investigated. Simulation results show that the contact pressure and von Mises stress decrease significantly with a modest wear depth and remains quite in-sensitive to the cup inclination angle and wear depth up to 1.64 mm. With wear depth further up to 2.46 mm, the cup thickness (i.e. cup thinning on worn region) may be more predominant than increasing of contact area between the cup and the head. The wear on the inner surface of the cup is found to rule out the overall contact pressure and stress in the implant. Furthermore, individual and combined effects of both important parameters are analysed and discussed with respect to available clinical/laboratory studies.

Design and Analysis of Cooperative Cable Parallel Manipulators for Multiple Mobile Cranes

Directory of Open Access Journals (Sweden)

Bin Zi

2012-11-01

Full Text Available The design, dynamic modelling, and workspace are presented in this paper concerning cooperative cable parallel manipulators for multiple mobile cranes (CPMMCs. The CPMMCs can handle complex tasks that are more difficult or even impossible for a single mobile crane. Kinematics and dynamics of the CPMMCs are studied on the basis of geometric methodology and d'Alembert's principle, and a mathematical model of the CPMMCs is developed and presented with dynamic simulation. The constant orientation workspace analysis of the CPMMCs is carried out additionally. As an example, a cooperative cable parallel manipulator for triple mobile cranes with 6 Degrees of Freedom is investigated on the basis of the above design objectives.

DESIGNING MLEARNING: Tapping Into The Mobile Revolution For Organizational Performance

Directory of Open Access Journals (Sweden)

Ozlem OZAN

2012-01-01

Full Text Available From past to the present, the learning need has increasingly grown. In this way, education and learning processes have also evolved; education has continuously changed shell along with social transformation and development. The communication and data transfer possibilities created by mobile technologies can significantly reduce dependence on fixed locations for work and study, and thus have the potential to revolutionize the way we work and learn (Peters, 2009. In this context, M-learning is considered as a new channel for the individuals who are mobile but aim to learn, and mobile learning design has became a new issue educators should be aware of. This is one of the basic books in the field of mobile learning design.The author of the book is Clark Quinn. He leads learning system design through Quinnovation, and is a founding principal of the Internet Time Alliance, helping organizations work smarter. He provides strategic solutions to Fortune 500, education, government, and not-for-profit organizations. Previously, he headed research and development efforts for Knowledge Universe Interactive Studio, and before that held management positions at Open Net and Access CMC, two Australian initiatives in internet-based multimedia and education. Clark earned a Ph.D. in applied cognitive science from the University of California. He has held positions at the University of New South Wales, the University of Pittsburgh's Learning Research and Development Center, and San Diego State University's Center for Research in Mathematics and Science Education (Quinn, 2011.Target audience of the book is instructional designers and instructors in K-12, higher education and corporate training departments; book is useful for also developers, media experts, managers, and anyone with responsibility for supporting performance in organizations, as well.

That Was Then, This Is Now: Replacing the Mobile-Optimized Site with Responsive Design

Directory of Open Access Journals (Sweden)

Laurie M. Bridges

2013-12-01

Full Text Available As mobile technologies continue to evolve, libraries seek sustainable ways to keep up with these changes and to best serve our users.  Previous library mobile usability research has examined tasks users predict they might be likely to perform, but little is known about what users actually do on a mobile-optimized library site.  This research used a combination of survey methodology and web analytics to examine what tasks users actually carry out on a library mobile site.  The results indicate that users perform an array of passive and active tasks and do not want content choices to be limited on mobile devices.  Responsive design is described as a long-term solution for addressing both designers and users’ needs.

A generalized strategy for designing (19)F/(1)H dual-frequency MRI coil for small animal imaging at 4.7 Tesla.

Science.gov (United States)

Hu, Lingzhi; Hockett, Frank D; Chen, Junjie; Zhang, Lei; Caruthers, Shelton D; Lanza, Gregory M; Wickline, Samuel A

2011-07-01

To propose and test a universal strategy for building (19) F/(1) H dual-frequency RF coil that permits multiple coil geometries. The feasibility to design (19) F/(1) H dual-frequency RF coil based on coupled resonator model was investigated. A series capacitive matching network enables robust impedance matching for both harmonic oscillating modes of the coupled resonator. Two typical designs of (19) F/(1) H volume coils (birdcage and saddle) at 4.7T were implemented and evaluated with electrical bench test and in vivo (19) F/(1) H dual-nuclei imaging. For various combinations of internal resistances of the sample coil and secondary resonator, numerical solutions for the tunable capacitors to optimize impedance matching were obtained using a root-seeking program. Identical and homogeneous B1 field distribution at (19) F and (1) H frequencies were observed in bench test and phantom image. Finally, in vivo mouse imaging confirmed the sensitivity and homogeneity of the (19) F/(1) H dual-frequency coil design. A generalized strategy for designing (19) F/(1) H dual-frequency coils based on the coupled resonator approach was developed and validated. A unique feature of this design is that it preserves the B1 field homogeneity of the RF coil at both resonant frequencies. Thus it minimizes the susceptibility effect on image co-registration. Copyright © 2011 Wiley-Liss, Inc.

Rational In Silico Design of an Organic Semiconductor with Improved Electron Mobility.

Science.gov (United States)

Friederich, Pascal; Gómez, Verónica; Sprau, Christian; Meded, Velimir; Strunk, Timo; Jenne, Michael; Magri, Andrea; Symalla, Franz; Colsmann, Alexander; Ruben, Mario; Wenzel, Wolfgang

2017-11-01

Organic semiconductors find a wide range of applications, such as in organic light emitting diodes, organic solar cells, and organic field effect transistors. One of their most striking disadvantages in comparison to crystalline inorganic semiconductors is their low charge-carrier mobility, which manifests itself in major device constraints such as limited photoactive layer thicknesses. Trial-and-error attempts to increase charge-carrier mobility are impeded by the complex interplay of the molecular and electronic structure of the material with its morphology. Here, the viability of a multiscale simulation approach to rationally design materials with improved electron mobility is demonstrated. Starting from one of the most widely used electron conducting materials (Alq 3 ), novel organic semiconductors with tailored electronic properties are designed for which an improvement of the electron mobility by three orders of magnitude is predicted and experimentally confirmed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Automated Hydraulic System Design and Power Management in Mobile Applications

DEFF Research Database (Denmark)

Pedersen, Henrik Clemmensen

force, torque and power density. One of these areas is the mobile hydraulic area, which generally comprise all type of off-highway machinery, such as construction equipment, agricultural equipment etc. But where hydraulic systems earlier was designed with primary focus on cost, dynamic performance...... and accuracy, energy consumption is becoming an ever more important design parameter. At the same time as the first oil crisis the first hydraulic load sensing (LS) systems also emerged on the market, which, compared to the other systems of the time, offered significant energy saving potentials and which today...... are found on most medium and high-end mobile hydraulic machinery. Despite the energy saving potentials that these systems posses, compared to the other open-circuit hydraulic system topologies, LS-system may still be subject to very low system efficiencies if not designed correctly. This is typically...

Module-based structure design of wheeled mobile robot

Directory of Open Access Journals (Sweden)

Z. Luo

2018-02-01

Full Text Available This paper proposes an innovative and systematic approach for synthesizing mechanical structures of wheeled mobile robots. The principle and terminologies used for the proposed synthesis method are presented by adopting the concept of modular design, isomorphic and non-isomorphic, and set theory with its associated combinatorial mathematics. The modular-based innovative synthesis and design of wheeled robots were conducted at two levels. Firstly at the module level, by creative design and analysing the structures of classic wheeled robots, a wheel module set containing four types of wheel mechanisms, a suspension module set consisting of five types of suspension frames and a chassis module set composed of five types of rigid or articulated chassis were designed and generalized. Secondly at the synthesis level, two kinds of structure synthesis modes, namely the isomorphic-combination mode and the non-isomorphic combination mode were proposed to synthesize mechanical structures of wheeled robots; which led to 241 structures for wheeled mobile robots including 236 novel ones. Further, mathematical models and a software platform were developed to provide appropriate and intuitive tools for simulating and evaluating performance of the wheeled robots that were proposed in this paper. Eventually, physical prototypes of sample wheeled robots/rovers were developed and tested so as to prove and validate the principle and methodology presented in this paper.

New Design of Mobile Robot Path Planning with Randomly Moving Obstacles

Directory of Open Access Journals (Sweden)

T. A. Salih

2013-05-01

Full Text Available The navigation of a mobile robot in an unknown environment has always been a very challenging task. In order to achieve safe and autonomous navigation, the mobile robot needs to sense the surrounding environment and plans a collision-free path. This paper focuses on designing and implementing a mobile robot which has the ability of navigating smoothly in an unknown environment, avoiding collisions, without having to stop in front of obstacles, detecting leakage of combustible gases and transmitting a message of detection results to the civil defense unit automatically through the Internet to the E-mail. This design uses the implementation of artificial neural network (ANN on a new technology represented by Field Programmable Analog Array (FPAA for controlling the motion of the robot. The robot with the proposed controller is tested and has completed the required objective successfully.

Design of 6 MeV X-band electron linac for dual-head gantry radiotherapy system

Science.gov (United States)

Shin, Seung-wook; Lee, Seung-Hyun; Lee, Jong-Chul; Kim, Huisu; Ha, Donghyup; Ghergherehchi, Mitra; Chai, Jongseo; Lee, Byung-no; Chae, Moonsik

2017-12-01

A compact 6 MeV electron linac is being developed at Sungkyunkwan University, in collaboration with the Korea atomic energy research institute (KAERI). The linac will be used as an X-ray source for a dual-head gantry radiotherapy system. X-band technology has been employed to satisfy the size requirement of the dual-head gantry radiotherapy machine. Among the several options available, we selected a pi/2-mode, standing-wave, side-coupled cavity. This choice of radiofrequency (RF) cavity design is intended to enhance the shunt impedance of each cavity in the linac. An optimum structure of the RF cavity with a high-performance design was determined by applying a genetic algorithm during the optimization procedure. This paper describes the detailed design process for a single normal RF cavity and the entire structure, including the RF power coupler and coupling cavity, as well as the beam dynamics results.

Dual shear plate power processor packaging design. [for Solar Electric Propulsion spacecraft

Science.gov (United States)

Franzon, A. O.; Fredrickson, C. D.; Ross, R. G.

1975-01-01

The use of solar electric propulsion (SEP) for spacecraft primary propulsion imposes an extreme range of operational and environmental design requirements associated with the diversity of missions for which solar electric primary propulsion is advantageous. One SEP element which is particularly sensitive to these environmental extremes is the power processor unit (PPU) which powers and controls the electric ion thruster. An improved power processor thermal-mechanical packaging approach, referred to as dual shear plate packaging, has been designed to accommodate these different requirements with minimum change to the power processor design. Details of this packaging design are presented together with test results obtained from thermal-vacuum and structural-vibration tests conducted with prototype hardware.

Optimization of a miniature short-wavelength infrared objective optics of a short-wavelength infrared to visible upconversion layer attached to a mobile-devices visible camera

Science.gov (United States)

Kadosh, Itai; Sarusi, Gabby

2017-10-01

The use of dual cameras in parallax in order to detect and create 3-D images in mobile devices has been increasing over the last few years. We propose a concept where the second camera will be operating in the short-wavelength infrared (SWIR-1300 to 1800 nm) and thus have night vision capability while preserving most of the other advantages of dual cameras in terms of depth and 3-D capabilities. In order to maintain commonality of the two cameras, we propose to attach to one of the cameras a SWIR to visible upconversion layer that will convert the SWIR image into a visible image. For this purpose, the fore optics (the objective lenses) should be redesigned for the SWIR spectral range and the additional upconversion layer, whose thickness is mobile device visible range camera sensor (the CMOS sensor). This paper presents such a SWIR objective optical design and optimization that is formed and fit mechanically to the visible objective design but with different lenses in order to maintain the commonality and as a proof-of-concept. Such a SWIR objective design is very challenging since it requires mimicking the original visible mobile camera lenses' sizes and the mechanical housing, so we can adhere to the visible optical and mechanical design. We present in depth a feasibility study and the overall optical system performance of such a SWIR mobile-device camera fore optics design.

Dual-Beam Antenna Design for Autonomous Sensor Network Applications

Directory of Open Access Journals (Sweden)

Jean-Marie Floc'h

2012-01-01

Full Text Available This paper describes our contribution in the ANR project called CAPNET dedicated to the site security (autonomous sensor network. The network is autonomous in term of energy and it is very easy to deploy on the site (the time to deploy each node of the network is around 10 minutes. The first demonstrator was deployed in the fire base station of Brest, France with 10 nodes with a security perimeter around 1.5 km. Our contribution takes place in the field of antennas, with the development of two systems: a single-beam antenna reserved for the supervisor or the last node of the network, and a dual-beam antenna dedicated to the node in linear configuration. For the design and optimization of antennas, we use HFSS CAD software from ANSOFT. The antennas have been designed and successfully measured.

"Design for Somebody" - Approach Enabling Mobile Technology Development.

Science.gov (United States)

Sirkka, Andrew; Merilampi, Sari; Koivisto, Antti; Tommiska, Janika; Saarinen, Tatu-Pekka

2017-01-01

This paper presents case examples of Design for Somebody (DfS) philosophy used both in developing novel technologies and modifying existing main stream technologies applicable for users with special needs. DfS embodies variety of mobile technology approaches to generate personalised means to enable and motivate physical, cognitive and social skills development.

Design of a hybrid command and control mobile botnet

CSIR Research Space (South Africa)

Pieterse, H

2013-05-01

Full Text Available and control mobile botnet. The hybrid design explores the efficiency of multiple command and control channels against the following objectives: no single point of failure within the topology, low cost for command dissemination, limited network activities...

User-centric incentive design for participatory mobile phone sensing

Science.gov (United States)

Gao, Wei; Lu, Haoyang

2014-05-01

Mobile phone sensing is a critical underpinning of pervasive mobile computing, and is one of the key factors for improving people's quality of life in modern society via collective utilization of the on-board sensing capabilities of people's smartphones. The increasing demands for sensing services and ambient awareness in mobile environments highlight the necessity of active participation of individual mobile users in sensing tasks. User incentives for such participation have been continuously offered from an application-centric perspective, i.e., as payments from the sensing server, to compensate users' sensing costs. These payments, however, are manipulated to maximize the benefits of the sensing server, ignoring the runtime flexibility and benefits of participating users. This paper presents a novel framework of user-centric incentive design, and develops a universal sensing platform which translates heterogenous sensing tasks to a generic sensing plan specifying the task-independent requirements of sensing performance. We use this sensing plan as input to reduce three categories of sensing costs, which together cover the possible sources hindering users' participation in sensing.

Cross-Layer Design Approach for Power Control in Mobile Ad Hoc Networks

Directory of Open Access Journals (Sweden)

A. Sarfaraz Ahmed

2015-03-01

Full Text Available In mobile ad hoc networks, communication among mobile nodes occurs through wireless medium The design of ad hoc network protocol, generally based on a traditional “layered approach”, has been found ineffective to deal with receiving signal strength (RSS-related problems, affecting the physical layer, the network layer and transport layer. This paper proposes a design approach, deviating from the traditional network design, toward enhancing the cross-layer interaction among different layers, namely physical, MAC and network. The Cross-Layer design approach for Power control (CLPC would help to enhance the transmission power by averaging the RSS values and to find an effective route between the source and the destination. This cross-layer design approach was tested by simulation (NS2 simulator and its performance over AODV was found to be better.

Design of a Mobile Application for Transfusion Medicine.

Science.gov (United States)

Albornoz, M A; Márquez, S; Rubin, L; Luna, D

2017-01-01

One of the most frequent error in transfusion medicine is the failure in verifying the patient's identity prior to transfusion. This paper describes the design and development of a Mobile Application (MA) for transfusion medicine. The app uses barcode and QR reading technology for the verification of the patient's identity and the administration of blood components when making a blood transfusion. Physicians, developers, technicians of transfusion medicine and a User Centered Design team participated in the design. The inclusion of end users was fundamental to get full representativeness of their workflow. The project was based on agile methodologies of project management and software development.

Precise Design of Phosphorescent Molecular Butterflies with Tunable Photoinduced Structural Change and Dual Emission.

Science.gov (United States)

Zhou, Chenkun; Tian, Yu; Yuan, Zhao; Han, Mingu; Wang, Jamie; Zhu, Lei; Tameh, Maliheh Shaban; Huang, Chen; Ma, Biwu

2015-08-10

Photoinduced structural change (PSC) is a fundamental excited-state dynamic process in chemical and biological systems. However, precise control of PSC processes is very challenging, owing to the lack of guidelines for designing excited-state potential energy surfaces (PESs). A series of rationally designed butterfly-like phosphorescent binuclear platinum complexes that undergo controlled PSC by Pt-Pt distance shortening and exhibit tunable dual (greenish-blue and red) emission are herein reported. Based on the Bell-Evans-Polanyi principle, it is demonstrated how the energy barrier of the PSC, which can be described as a chemical-reaction-like process between the two energy minima on the first triplet excited-state PES, can be controlled by synthetic means. These results reveal a simple method to engineer the dual emission of molecular systems by manipulating PES to control PSC. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Revised Interface for the ARL Topodef Mobility Design Tool

Science.gov (United States)

2012-04-01

designed paths as though moving down a conveyor belt . Giving paths an existence independent of the nodes that travel along them not only makes their...A Revised Interface for the ARL Topodef Mobility Design Tool by Andrew J. Toth and Michael Christensen ARL-TR-5980 April 2012...Disclaimers The findings in this report are not to be construed as an official Department of the Army position unless so designated by other

Design of inspection equipment vehicle of mobile cobalt-60 container scanner

International Nuclear Information System (INIS)

Zhang Yanmin; An Jigang; Zhou Liye; Liu Yisi; Wu Zhifang; Xiang Xincheng; Huang Songling

2000-01-01

The author introduced the design principle of Inspection Equipment Vehicle of TCM-SCAN Mobile 60 Co container inspection system. Three schemes had been compared. The scheme of scan gate in form of pucker-able rails standing on the vehicle was determined. Prototype was prepared in September 1999. Mobile 60 Co container inspection system had the same inspection performance of fixed 60 Co container inspection system

Designing a Mobile Application: The Case of iAdvocate

Directory of Open Access Journals (Sweden)

Alan R. Foley

2012-01-01

Full Text Available In this article, the design of a mobile application (app called iAdvocate is illustrated. The goal of iAdvocate is to share and develop specific strategies with parents of children with disabilities for working collaboratively with a school team to improve their children’s education. iAdvocate uses problem-based learning strategies, simulations, and provides contextual access resources to build parental advocacy skills and knowledge. iAdvocate provides parents with both information and strategies regarding their educational rights and getting their child’s needs met. The goal of iAdvocate is to share and develop specific strategies with parents for working collaboratively with a school team to improve their children’s education. iAdvocate contains three sections: strategies, a compilation of approaches that parents can pursue as advocates; resources, which lists and, where possible, links to such references as laws, books, articles, web sites, video presentations, and organizations that provide information on inclusive education; and, responses, which features simulated interactions, such as replies to common statements made by school professionals regarding services and accommodations for children. This case illustrates the design processes and techniques used to develop an instructional mobile application by presenting the background and context of the project, initial design and design iterations, negative case analysis, and prototyping. Additional documents illustrating the project background, and design process are also included.

Extend Course for Product Designer in Digital Mobile Era

Science.gov (United States)

CHAO, Fang-Lin; LIU, Tzu-Heng; HUANG, Xian-Chun

2017-12-01

Product design refers to a system of processes from confirming a product’s specifications to product’s structure. Form, technology, and needs must be considered simultaneously to ensure qualities. In recent years, with the advancement of smartphone technology, many products are connected with apps. Designers cannot exclude themselves from this new wave of the trend. In this article, household hydroponic products design is used as an example, to show the close relationship between digital mobile technology and product design in the contemporary world. Regularly measure the amount of liquid to be added is difficult for a consumer who has no professional experience. To facilitate the introduction of small-scale aquaculture systems into the home, we proposed sensor hardware combined with App software, measured EC and pH value and transmitted to the phone. The app can calculate and display the amount of added and control the amount of inserted through a Bluetooth connection. The physical design needs to take into account the connection between the electronic parts and the circuit board, and interface operation. Thus, not only the model of the product but also the user interface has to be integrated to show the product's quality completely. Besides, authors made reflection upon the necessity for adjustments for interdisciplinary courses under the changing digital mobile era. Also, under the current curriculum structure, possible teaching approach is expressed for extending student’s feasibility.

Design, construction and evaluation of a meteorological mobile mast ...

African Journals Online (AJOL)

A 30 metre meteorological mobile mast has been designed and constructed for upper air profile measurements. The parameters to be measured are wind speed, wind direction, temperature and relative humidity. The sensors for each parameter to be measured are constructed with locally available materials.

Evolving the Design of a Mobile Application to Support Transition to Tertiary Education

Directory of Open Access Journals (Sweden)

Yu Zhao

2017-11-01

Full Text Available Students’ transition to tertiary education plays a critical role in their overall post-secondary experience. Even though educational institutions have designed and implemented various transition support programs, most of them still struggle to collect detailed information and provide tailored and timely support to students. With the high adoption rate of smart phones among university students, mobile applications can be used as a platform to provide personalized support throughout the transition, which has the potential to address the shortcomings of existing programs. Moreover, the use of mobile applications to support the transition to tertiary education can benefit from emerging techniques to design applications to support individuals through transition processes. In this paper, we present the design and development process of myUniMate, a mobile application that allows students to track and reflect on information from multiple aspects of their university lives. The paper describes the user-centered design approach used in the design, the implementation process, and how the initial version evolved based on our previous study. We conducted a 4-week field trial with first year university students to validate our design.

Nonword Reading: Comparing Dual-Route Cascaded and Connectionist Dual-Process Models with Human Data

Science.gov (United States)

Pritchard, Stephen C.; Coltheart, Max; Palethorpe, Sallyanne; Castles, Anne

2012-01-01

Two prominent dual-route computational models of reading aloud are the dual-route cascaded (DRC) model, and the connectionist dual-process plus (CDP+) model. While sharing similarly designed lexical routes, the two models differ greatly in their respective nonlexical route architecture, such that they often differ on nonword pronunciation. Neither…

Mobile Collaborative Informal Learning Design: Study of collaborative effectiveness using Activity Theory

Directory of Open Access Journals (Sweden)

Hasnain Zafar Baloch

2012-07-01

Full Text Available Smart Mobile Devices (SMD are there for many years but using them as learning tools started to emerge as new research area. The trend to merge collaborative learning methodology by using mobile devices in informal context is important for implementation of Learner Centric Learning (LCL. Survey and numerous studies show that more than 95% of students in colleges are users of these smart mobile devices in developed world. Developing counties are also catching up and we can see this percentage is almost same in university level in these countries. Students are using SMDs for learning in some form. Higher education Institutions also try to embark their E-learning to Mobile learning (ML. The aim of this paper is to do propose operational framework for designing Mobile Collaborative Informal learning activities using SMDs. Show results of experimental and case study done to study the Mobile Collaborative Informal learning using Activity Theory (AT. Core Components of framework are Mobile Learning Activities/Objects, Wireless/Mobile Smart devices, Collaborative knowledge and Collaborative learning. The research mention here is its infancy stage.

Special Digital Monies: The Design of Alipay and WeChat Wallet for Mobile Payment Practices in China

OpenAIRE

Kow , Yong ,; Gui , Xinning; Cheng , Waikuen

2017-01-01

Part 2: Social Media and Design Innovation; International audience; While research studies of digital and mobile payment systems in HCI have pointed out design opportunities situated within informal and nuanced mobile contexts, we have not yet understood how we can design digital monies to allow users to use monies more easily in these contexts. In this study, we examined the design of Alipay and WeChat Wallet, two successful mobile payment apps in China, which have been used by Chinese users...

Identifying Instructional Strategies Used to Design Mobile Learning in a Corporate Setting

Science.gov (United States)

Jackson-Butler, Uletta

2016-01-01

The purpose of this qualitative embedded multiple case study was to describe what instructional strategies corporate instructional designers were using to design mobile learning and to understand from their experiences which instructional strategies they believed enhance learning. Participants were five instructional designers who were actively…

Designing appliances for mobile commerce and retailtainment

OpenAIRE

Roussos, George; Kourouthanassis, P.; Moussouri, T.

2003-01-01

In the emerging world of the new consumer and the `anytime, anywhere' mobile commerce, appliances are located at the collision point of the retailer and consumer agendas. The consequence of this is twofold: on the one hand appliances that were previously considered plain and utilitarian become entertainment devices and on the other, for the effective design of consumer appliances it becomes paramount to employ multidisciplinary expertise. In this paper, we discuss consumer perceptions of a re...

Mobile platform sampling for designing environmental sensor networks.

Science.gov (United States)

Budi, Setia; de Souza, Paulo; Timms, Greg; Susanto, Ferry; Malhotra, Vishv; Turner, Paul

2018-02-09

This paper proposes a method to design the deployment of sensor nodes in a new region where historical data is not available. A number of mobile platforms are simulated to build initial knowledge of the region. Further, an evolutionary algorithm is employed to find the optimum placement of a given number of sensor nodes that best represents the region of interest.

RACOON: a multiuser QoS design for mobile wireless body area networks.

Science.gov (United States)

Cheng, Shihheng; Huang, Chingyao; Tu, Chun Chen

2011-10-01

In this study, Random Contention-based Resource Allocation (RACOON) medium access control (MAC) protocol is proposed to support the quality of service (QoS) for multi-user mobile wireless body area networks (WBANs). Different from existing QoS designs that focus on a single WBAN, a multiuser WBAN QoS should further consider both inter-WBAN interference and inter-WBAN priorities. Similar problems have been studied in both overlapped wireless local area networks (WLANs) and Bluetooth piconets that need QoS supports. However, these solutions are designed for non-medical transmissions that do not consider any priority scheme for medical applications. Most importantly, these studies focus on only static or low mobility networks. Network mobility of WBANs will introduce unnecessary inter-network collisions and energy waste, which are not considered by these solutions. The proposed multiuser-QoS protocol, RACOON, simultaneously satisfies the inter WBAN QoS requirements and overcomes the performance degradation caused by WBAN mobility. Simulation results verify that RACOON provides better latency and energy control, as compared with WBAN QoS protocols without considering the inter-WBAN requirements.

Electromagnetic linear machines with dual Halbach array design and analysis

CERN Document Server

Yan, Liang; Peng, Juanjuan; Zhang, Lei; Jiao, Zongxia

2017-01-01

This book extends the conventional two-dimensional (2D) magnet arrangement into 3D pattern for permanent magnet linear machines for the first time, and proposes a novel dual Halbach array. It can not only effectively increase the radial component of magnetic flux density and output force of tubular linear machines, but also significantly reduce the axial flux density, radial force and thus system vibrations and noises. The book is also the first to address the fundamentals and provide a summary of conventional arrays, as well as novel concepts for PM pole design in electric linear machines. It covers theoretical study, numerical simulation, design optimization and experimental works systematically. The design concept and analytical approaches can be implemented to other linear and rotary machines with similar structures. The book will be of interest to academics, researchers, R&D engineers and graduate students in electronic engineering and mechanical engineering who wish to learn the core principles, met...

Mobile health units. Design and implementation considerations.

Science.gov (United States)

Murphy, D C; Klinghoffer, I; Fernandez-Wilson, J B; Rosenberg, L

2000-11-01

The decision to provide health care services with a mobile van is one which educational and service facilities are increasingly pursuing. The benefits include: The potential to increase the availability of services to underserved populations where access to care is perceived to be one reason for underuse of available services. The opportunity to increase and broaden the educational experiences of students in a training program. The opportunity to develop a sense of social responsibility in the health care provider. The process of deciding to pursue a van purchase is complicated, and administrators may best be served by obtaining experienced consultants to help them fully comprehend the issues involved. After the decision to purchase a mobile unit is made, it is necessary to focus on van requirements and design to meet federal, state, and city codes concerning motor vehicles and health requirements. Some modifications of one's standard practices are needed because of these codes. Being aware of them in advance will allow a smooth project completion. This article provides information about some of the steps required to implement a mobile unit. The approximate time from initial concept to van delivery was 1 year, with one fully dedicated project coordinator working to assure the project's success in such a short time frame. Seeing the gratified personnel and students who serve the children on the "Smiling Faces, Going Places" Mobile Dental Van of the NYUCD (see Figure 2), and knowing the children would otherwise not have received such services, allows the health care professionals involved to feel the development of this van is an exciting mechanism for delivery of health care to individuals who would otherwise go without.

A Participatory Design Approach for a Mobile App-Based Personal Response System

Science.gov (United States)

Song, Donggil; Oh, Eun Young

2016-01-01

This study reports on a participatory design approach including the design, development, implementation, and evaluation of a mobile app-based personal response system (PRS). The first cycle formulated initial design principles through context and needs analysis; the second utilized the collaboration with instructors and experts embodying specific…

BASED DESIGN MOBILE LEARNING COURSE ON ANDROID OPERATING SYSTEM IN INDONESIA STMIK PADANG

Directory of Open Access Journals (Sweden)

Liranti Rahmelina

2017-09-01

Full Text Available This research in the wake of the habit among students and lecturers in the uses smartphones, mostly only used to access social networks such as facebook and twitter and have yet to take an important role in education. This study aims to produce a system design mobile learning courses Operating Systems in STMIK Indonesia Padang, preferably in the learning process in the subject of the Operating System, the nature of memorization to books and teaching conventional. These mobile devices have a degree of flexibility and portability that enable high students can access materials, referrals and information related to learning anytime and anywhere. mobile learning android ased Operating System. This material requires a solid understanding and so we need learning support media and can be repeated whenever and wherever students need. The design of supporting mobile learning media is expected to facilitate the needs of students and teachers to learn the material at any time without any limitation of time and place. This study uses SDLC (System Development Life Cycle is a method that describes the system development life cycle in the design and development of information systems. The programming language used is Java, using Eclipse IDE.

Design of fixed and mobile PET/CT facilities: the similarities and the challenges

International Nuclear Information System (INIS)

Peet, Debbie J.; Pryor, M.

2008-01-01

Design of PET/CT facilities present particular challenges for Radiation Protection. The high energy gamma ray emitted from the radionuclides used, the prolonged uptake period with patients within the facility and the relatively high dose rates from those patients result in some shielding being required and a careful consideration of the layout within each unit. This paper will present the approach used for the design of a fixed facility and will present staff dose data demonstrating that the design has resulted in low staff doses. The approach used to design mobile facilities will then be described, and a consideration of the doses received on this type of unit will also be given. The fixed facility was installed into a wooden clad building and was extremely small. The building was shared with other non radiation workers. Walls were constructed from dense concrete blocks and the layout arranged to prevent a direct line of site between the patient and workers at any point apart from the scan room where a lead glass window was used. For the mobile facility lead was used as the shielding material. The basic approach was to maximise the distance between operators and resting patients. Because of weight restrictions and limitation on the dose rate at the scanner defined by the scanner manufacturer, a higher dose constraint had to be adopted for staff on the unit. Additional complications include the mobility of the unit which can be parked adjacent to buildings with a variety of construction materials. Results of whole body monitoring for staff in the fixed facility over 5 years will be presented with the results from the mobile units over the last year. These will demonstrate the difficulties in keeping doses as low as reasonably achievable in the mobile scenario and the importance of designing the facility with staff dose in mind from the outset. (author)

A formal account of the dual extension of knowledge and concept in C-K design theory

NARCIS (Netherlands)

Hendriks, L.; Kazakci, A.O.; Marjanović, D.; Štorga, M.; Pavković, N.; Bojčetić, N.

2010-01-01

The paper presents a contribution to the formalization efforts of C-K design theory. First, we analyze the notion of "dual expansion of concepts and knowledge" in C-K design theory and we discuss how such a reasoning process can be modeled using first-order logic. Then, we present a basic formal

The role of organizational strategy in the user-centered design of mobile applications

NARCIS (Netherlands)

Eshet, Eyal; de Reuver, G.A.; Bouwman, W.A.G.A.

2017-01-01

Gathering insights on users and the contexts they use mobile applications is at the core of the user-centered design (UCD). Organizations find it strategically important to efficiently and effectively use these insights. With the proliferation of mobile applications, gaining timely and relevant

Designing an Educator Toolkit for the Mobile Learning Age

Science.gov (United States)

Burden, Kevin; Kearney, Matthew

2018-01-01

Mobile technologies have been described as 'boundary' objects which enable teachers and learners to transcend many of the barriers such as rigid schedules and spaces which have hitherto characterised traditional forms of education. However, educators need to better understand how to design learning scenarios which genuinely exploit the unique…

Study on general design of dual-DMD based infrared two-band scene simulation system

Science.gov (United States)

Pan, Yue; Qiao, Yang; Xu, Xi-ping

2017-02-01

Mid-wave infrared(MWIR) and long-wave infrared(LWIR) two-band scene simulation system is a kind of testing equipment that used for infrared two-band imaging seeker. Not only it would be qualified for working waveband, but also realize the essence requests that infrared radiation characteristics should correspond to the real scene. Past single-digital micromirror device (DMD) based infrared scene simulation system does not take the huge difference between targets and background radiation into account, and it cannot realize the separated modulation to two-band light beam. Consequently, single-DMD based infrared scene simulation system cannot accurately express the thermal scene model that upper-computer built, and it is not that practical. To solve the problem, we design a dual-DMD based, dual-channel, co-aperture, compact-structure infrared two-band scene simulation system. The operating principle of the system is introduced in detail, and energy transfer process of the hardware-in-the-loop simulation experiment is analyzed as well. Also, it builds the equation about the signal-to-noise ratio of infrared detector in the seeker, directing the system overall design. The general design scheme of system is given, including the creation of infrared scene model, overall control, optical-mechanical structure design and image registration. By analyzing and comparing the past designs, we discuss the arrangement of optical engine framework in the system. According to the main content of working principle and overall design, we summarize each key techniques in the system.

Coherent dual-frequency lidar system design for distance and speed measurements

Science.gov (United States)

Zheng, Xingyuan; Zhao, Changming; Zhang, Haiyang; Zheng, Zheng; Yang, Hongzhi

2018-01-01

Lidars have a wide range of applications in military detection and civilian remote sensing. Coherent Dual-Frequency Lidar (CDFL) is a new concept of laser radar that is using electrical coherence instead of optical coherence. It uses laser with two coherent frequency components as transmitting wave. The method is based on the use of an optically-carried radio frequency (RF) signal, which is the frequency difference between the two components, which is specially designed for distance and speed measurements. It not only ensures the system has the characteristics of high spatial resolution, high ranging and velocity precision of laser radar, but also can use mature signal processing technology of microwave radar, and it is a research direction that attracts more concern in recent years. A CDFL detection system is constructed and field experiment is carried out. In the system, a narrow linewidth fiber laser with a wavelength of 1064nm is adopted. The dual-frequency laser with frequency difference of 200MHz and 200.6MHz is obtained by acousto-optic frequency shift and recombination. The maximum output power of dual frequency laser is 200mW. The receiver consists of all-fiber balanced InGaAs photo-detector and homemade analog signal processing board. The experimental results show that the distance resolution and velocity resolution of the system are 0.1m and 0.1m/s separately when the working distance is greater than 200m, and the spatial resolution is 0.5mrad.

Meta-design Approach for Mobile Platforms Supporting Creative Tourism Experiences

DEFF Research Database (Denmark)

Tussyadiah, Iis P.

2013-01-01

with and interpretations of the local attributes of tourism destinations. The mobile system will integrate the sensory stimuli, the intense contact with cultural nuances and social network, the brand-based reputation, and the creative communities at tourism destinations into the iterative process of perception, conception......This paper conceptualizes the application of meta-design approach in the development of a mobile system supporting creative experiences for tourists. Specifically, for those working in creative industries, adaptive mobile system will facilitate effective tourists' interactions......, and expression of creative ideas among tourists. For destinations trying to highlight their unique characteristics as their value proposition, the development of such system may benefit them from a heightened sense of place due to on-going value co-creation. Individuals will benefit from such system from...

Correlation properties of dual polarized antennas with finite pattern orthogonality in mobile fading channels

Directory of Open Access Journals (Sweden)

G. Armbrecht

2007-06-01

Full Text Available Starting from planar broadband log.-per. antenna design, offering the possibility of dual-polarized reception properties, in this article a generalized mathematical approach for rapidly estimating the resulting signal correlation coefficient in a stochastically modeled propagation environment solely based on measured or simulated radiation characteristics of one single antenna element is presented. The obtained results are marking an upper limit and are describing the worst-case scenario according to the signal correlation at the antenna feeding points in terms of line-of-sight (LOS reception in main beam direction. The knowledge of the derived relationship may be helpful especially for antenna designers to combine antenna performance values with the significant communication system performance parameters, as e.g. in case of Multiple-Input Multiple-Output (MIMO and diversity configurations.

Dual-task training effects on motor and cognitive functional abilities in individuals with stroke: a systematic review.

Science.gov (United States)

He, Ying; Yang, Lei; Zhou, Jing; Yao, Liqing; Pang, Marco Yiu Chung

2018-02-01

This systematic review aimed to examine the effects of dual-task balance and mobility training in people with stroke. An extensive electronic databases literature search was conducted using MEDLINE, PubMed, EBSCO, The Cochrane Library, Web of Science, SCOPUS, and Wiley Online Library. Randomized controlled studies that assessed the effects of dual-task training in stroke patients were included for the review (last search in December 2017). The methodological quality was evaluated using the Cochrane Collaboration recommendation, and level of evidence was determined according to the criteria described by the Oxford Center for Evidence-Based Medicine. About 13 articles involving 457 participants were included in this systematic review. All had substantial risk of bias and thus provided level IIb evidence only. Dual-task mobility training was found to induce more improvement in single-task walking function (standardized effect size = 0.14-2.24), when compared with single-task mobility training. Its effect on dual-task walking function was not consistent. Cognitive-motor balance training was effective in improving single-task balance function (standardized effect size = 0.27-1.82), but its effect on dual-task balance ability was not studied. The beneficial effect of dual-task training on cognitive function was provided by one study only and thus inconclusive. There is some evidence that dual-task training can improve single-task walking and balance function in individuals with stroke. However, any firm recommendation cannot be made due to the weak methodology of the studies reviewed.

Basic concepts about application of dual vibration absorbers to seismic design of nuclear piping systems

International Nuclear Information System (INIS)

Hara, F.; Seto, K.

1987-01-01

The design value of damping for nuclear piping systems is a vital parameter in ensuring safety in nuclear plants during large earthquakes. Many experiments and on-site tests have been undertaken in nuclear-industry developed countries to determine rational design values. However damping value in nuclear piping systems is so strongly influenced by many piping parameters that it shows a tremendous dispersion in its experimental values. A new trend has recently appeared in designing nuclear pipings, where they attempt to use a device to absorb vibration energy induced by seismic excitation. A typical device is an energy absorbing device, made of a special material having a high capacity of plasticity, which is installed between the piping and the support. This paper deals with the basic study of application of dual vibration absorbers to nuclear piping systems to accomplish high damping value and reduce consequently seismic response at resonance frequencies of a piping system, showing their effectiveness from not only numerical calculation but also experimental evaluation of the vibration responses in a 3D model piping system equipped with dual two vibration absorbers

Design of a 'two-ion-source' charge breeder with a dual frequency ECR ion source

International Nuclear Information System (INIS)

Naik, D.; Naik, V.; Chakrabarti, A.; Dechoudhury, S.; Nayak, S.K.; Pandey, H.K.; Nakagawa, T.

2005-01-01

A charge breeder, 'two-ion-source' has been designed which consists of a surface ionisation source followed by an ECR ion source working in two-frequency mode. In this system low charge state ion beam (1+)of radioactive atoms are obtained from the first ion source close to the target chamber and landed into the ECR where those are captured and become high charged state after undergoing a multi ionisation process. This beam dynamics design has been done to optimise the maximum possible transfer of 1 + beam from the first ion source into the ECR, its full capture within the ECR zone and design of an efficient dual frequency ECR. The results shows that 1 + beam of 100 nA and 1μA (A=100) are successfully transmitted and it's beam size at the centre of ECR zone are 12 mm and 21 mm respectively, which are very less than 65 mm width ECR zone of dual frequency ECR heating at 14 GHz and 10 GHz. (author)

Dual-task related gait changes in individuals with trans-tibial lower extremity amputation.

Science.gov (United States)

Hunter, Susan W; Frengopoulos, Courtney; Holmes, Jeffrey; Viana, Ricardo; Payne, Michael W C

2018-03-01

The improvement of gait and mobility are major rehabilitation goals following lower extremity amputations. However, when living in the community many daily activities require the multitasking of motor and cognitive tasks. The dual-task paradigm can be used to evaluate the concurrent performance of mobility and cognitive tasks. The purpose of this study was to evaluate the effects of dual-task gait testing in older adults with trans-tibial amputations. Twenty-four people (15 men, mean age ± SD, 62.72 ± 8.59) with trans-tibial amputation walked on an electronic walkway at i) self-selected comfortable pace and ii) self-selected comfortable pace while counting backwards by threes from a number randomly selected between 100 and 150. Cognitive performance, in the form of corrected response rate, was also evaluated as a single-task. The dual-task testing produced poorer performance in velocity (single-task = 58.15 ± 23.16 cm/s, dual-task = 50.92 ± 21.16 cm/s, p = 0.008), cadence (single-task = 76.65 ± 15.84 steps/min, dual-task = 67.85 ± 15.76 steps/min, p = 0.002) and stride time (single-task = 1094 ± 458.28 ms, dual-task = 1241.44 ± 513.73 ms, p = 0.005). Step length, stance time and single limb support time symmetry were also affected, such that less time was spent on the amputated limb during the dual-task testing. Dual-task testing demonstrated interference resulting in a poor performance in both gait and cognitive performance in trans-tibial amputees. Further research is suggested to evaluate the change in cognition-mobility effects over time and the relationship of this value to future adverse events such as falls and successful outcomes such as community ambulation and reintegration. Copyright © 2018 Elsevier B.V. All rights reserved.

Design, manufacturing and commissioning of mobile unit for EDF (Dow Chemical process)

International Nuclear Information System (INIS)

Cangini, D.; Cordier, J.P.; PEC Engineering, Osny, France)

1985-01-01

To process their spent ion exchange resins and the liquid wastes, EDF has ordered from PEC a mobile unit using the DOW CHEMICAL binder. This paper presents the EDF's design requirements as well as the new French regulation for waste embedding. The mobile unit was started in January 1983 and commissioned successfully in January 1985 in the TRICASTIN EDF's power plant

Participatory research design in mobile health: Tablet devices for diabetes self-management.

Science.gov (United States)

Burford, Sally; Park, Sora; Dawda, Paresh; Burns, John

2015-01-01

Type 2 diabetes is a prevalent, chronic disease, which places significant burden on societies and individuals. This article reports the participatory research design of an exploratory study that introduces mobile tablet devices in the self-management of type 2 diabetes in a primary healthcare setting. Strategies from democratic dialogic theory were used in the design of the research to steer the participatory engagement between researchers and healthcare practitioners. The outcome of this phase of the research was the issue of six ‘invitations’ to 28 people with diabetes to frame their use of a mobile tablet device in managing their health. Those invitations were clustered in two themes, Empowered and Compelled, representing typical patient attitudes and behaviours. The work reported here sets the stage for a longitudinal and socially complex study that encompasses a new and comprehensive General Practitioner (GP) Super Clinic with an array of health and administrative staff, patients with a chronic health condition requiring continual self-management, a wide continuum of digital literacy capability in all participants and an ever-increasing digital society. It reports a novel research design methodology that merges democratic dialogic theory and participatory design, resulting in a grounded and agreed approach to a mobile health intervention.

Co-Designing Mobile Apps to Assist in Clinical Nursing Education: A Study Protocol.

Science.gov (United States)

O'Connor, Siobhan; Andrews, Tom

2016-01-01

Mobile applications (apps) to train health professionals is gaining momentum as the benefits of mobile learning (mLearning) are becoming apparent in complex clinical environments. However, most educational apps are generic, off-the-shelf pieces of software that do not take into consideration the unique needs of nursing students. The proposed study will apply a user-centred design process to create a tailored mobile app for nursing students to learn and apply clinical skills in practice. The app will be piloted and evaluated to understand how nursing students use mobile technology in clinical settings to support their learning and educational needs.

Design and parametric study on energy harvesting from bridge vibration using tuned dual-mass damper systems

Science.gov (United States)

Takeya, Kouichi; Sasaki, Eiichi; Kobayashi, Yusuke

2016-01-01

A bridge vibration energy harvester has been proposed in this paper using a tuned dual-mass damper system, named hereafter Tuned Mass Generator (TMG). A linear electromagnetic transducer has been applied to harvest and make use of the unused reserve of energy the aforementioned damper system absorbs. The benefits of using dual-mass systems over single-mass systems for power generation have been clarified according to the theory of vibrations. TMG parameters have been determined considering multi-domain parameters, and TMG has been tuned using a newly proposed parameter design method. Theoretical analysis results have shown that for effective energy harvesting, it is essential that TMG has robustness against uncertainties in bridge vibrations and tuning errors, and the proposed parameter design method for TMG has demonstrated this feature.

Dual-band dual-polarized array for WLAN applications

CSIR Research Space (South Africa)

Steyn, JM

2009-01-01

Full Text Available dual-band dual-polarized (DBDP) antenna design for WLAN applications. The antenna is in the form of an array consisting of four double-dipole radiators. The basic radiating element consists of a rhombus shaped dipole above a planar ground plane... the ground planes and the respective feedlines. Substrate cuts and difierent heights for the horizontal feedlines were necessary to achieve the latter. The 2nd conflguration (for vertical polarization) has a slightly difierent feeding network layout...

Design of a hybrid command and control mobile botnet: Presentation

CSIR Research Space (South Africa)

Pieterse, H

2013-03-01

Full Text Available smartphones controlled by a botmaster through a command and control network to serve a malicious purpose. This study presents the design of a hybrid command and control mobile botnet. It describes the propagation vectors, command and control channels...

Mobility Divides

DEFF Research Database (Denmark)

Jensen, Ole B.

Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments......’ in the everyday life and cast light on how design and ‘materialities of mobilites’ are creating differential mobilities across societies, social networks, and communities of practices.......Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments...

Mobile phase effects on the retention on polar columns with special attention to the dual hydrophilic interaction-reversed-phase liquid chromatography mechanism, a review.

Science.gov (United States)

Jandera, Pavel; Hájek, Tomáš

2018-01-01

Hydrophilic interaction liquid chromatography on polar columns in aqueous-organic mobile phases has become increasingly popular for the separation of many biologically important compounds in chemical, environmental, food, toxicological, and other samples. In spite of many new applications appearing in literature, the retention mechanism is still controversial. This review addresses recent progress in understanding of the retention models in hydrophilic interaction liquid chromatography. The main attention is focused on the role of water, both adsorbed by the column and contained in the bulk mobile phase. Further, the theoretical retention models in the isocratic and gradient elution modes are discussed. The dual hydrophilic interaction liquid chromatography reversed-phase retention mechanism on polar columns is treated in detail, especially with respect to the practical use in one- and two-dimensional liquid chromatography separations. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dual wound dc brush motor gearhead

Science.gov (United States)

Henson, Barrie W.

1986-01-01

The design requirements, the design, development tests and problems, the qualification and life test and the findings of the strip examination of a dual wound DC brushed motor gearhead are described. It is the only space qualified dual wound dc brushed motor gearhead in Europe.

Optimal Design and Hybrid Control for the Electro-Hydraulic Dual-Shaking Table System

Directory of Open Access Journals (Sweden)

Lianpeng Zhang

2016-08-01

Full Text Available This paper is to develop an optimal electro-hydraulic dual-shaking table system with high waveform replication precision. The parameters of hydraulic cylinders, servo valves, hydraulic supply power and gravity balance system are designed and optimized in detail. To improve synchronization and tracking control precision, a hybrid control strategy is proposed. The cross-coupled control using a novel based on sliding mode control based on adaptive reaching law (ASMC, which can adaptively tune the parameters of sliding mode control (SMC, is proposed to reduce the synchronization error. To improve the tracking performance, the observer-based inverse control scheme combining the feed-forward inverse model controller and disturbance observer is proposed. The system model is identified applying the recursive least squares (RLS algorithm and then the feed-forward inverse controller is designed based on zero phase error tracking controller (ZPETC technique. To compensate disturbance and model errors, disturbance observer is used cooperating with the designed inverse controller. The combination of the novel ASMC cross-coupled controller and proposed observer-based inverse controller can improve the control precision noticeably. The dual-shaking table experiment system is built and various experiments are performed. The experimental results indicate that the developed system with the proposed hybrid control strategy is feasible and efficient and can reduce the tracking errors to 25% and synchronization error to 16% compared with traditional control schemes.

Design and Analysis of Planetary Gear and Track Hybrid Mobile Robot

Directory of Open Access Journals (Sweden)

LEI Ning

2014-10-01

Full Text Available In order to improve the ability of obstacle negotiation and stability of mobile robot under unstructured environment, a new type of planetary gear and track hybrid mobile robot has been designed. This robot can surmount lower obstacles by its gravity and inertia of epicyclic gear train, otherwise, higher obstacles can be negotiated by the track arms. The two-part body connected by universal coupling can adjust to different terrain. Also, key parts of the robot were analyzed by ANSYS. According to the analysis results, an optimization design has been put forward .The analysis results can be concluded that the total deformation of the track arm can be reduced from 289 mm to 41.9 mm and the stiffness was improved.

Mechanical design issues and resolutions of a dual cooled fuel for the OPR-1000

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyung-Kyu, E-mail: hkkim1@kaeri.re.kr [Innovative Nuclear Fuel Division, Korea Atomic Energy Research Institute, 1045 Daedeokdaero, Yuseong, Daejeon, 305-353 (Korea, Republic of); Kim, Jae-Yong; Yoon, Kyung-Ho [Innovative Nuclear Fuel Division, Korea Atomic Energy Research Institute, 1045 Daedeokdaero, Yuseong, Daejeon, 305-353 (Korea, Republic of)

2011-06-15

Highlights: > Thickness of outer cladding tube is determined by using the elastic buckling criterion. > Growth difference of the inner and outer claddings will not cause fuel rod bowing. > Structural components are designed without a drastic change of the conventional ones. - Abstract: A dual cooled fuel is recently brought into focus due to its potential of considerable power uprating. The purpose of present work is to realize the innovative concept of a dual cooled fuel to be a fuel assembly structure compatible with the OPR-1000 system. Under the framework, the critical issues such as the outer cladding thickness and the growth difference of the inner and outer cladding tubes are dealt with in this paper. We designed the thickness of outer cladding tube by using the elastic buckling criterion and safety factor analysis. From the concern of the inner cladding's bowing during irradiation, it was suggested that the outer cladding would grow more than the inner one by applying different microstructures to the inner and outer cladding tubes. It was noted that the gap between fuel rods would not be narrowed further during the different irradiation growth. The structural components such as fuel rod supporting structure, top and bottom end pieces and guide tubes could be designed without a drastic change of those of the conventional fuel. Candidate designs of the components are also presented.

Design aspects of 50 m3/d prototype mobile desalination unit

International Nuclear Information System (INIS)

Bhattacharyya, K.P.; Srivastava, V.K.; Tewari, P.K.

2004-01-01

Supply of fresh water on sustainable basis to all inhabitants is the national responsibility. As a part of national programme to improve quality of life in our society, Desalination Division, BARC has undertaken a project on construction of barge mounted mobile desalination unit of capacity 50 m 3 /d under the domain of health care. The plant is capable of producing safe drinking water at any site and condition where potable water is limited from water sources as lakes and dams, spring, river, bores, estuaries, and open sea. The unit is also capable of purifying nuclear, biological and chemical contaminated water source namely arsenic, fluoride and nitrate. However, the main objective of this prototype mobile unit is to derive potable water from sea water. The barge mounted desalination plant could be useful to the people on shore, in areas like Rann of Kutch or coastal areas which had been affected by natural calamities like floods or severe drought; in small islands like Lakshadeep and Andaman and Nicobar. This type of mobile unit could also be useful for constructional purposes of plants located adjoining to the shore. The plant encompasses state of art reverse osmosis (RO) technology with membrane based ultrafiltration (UF) pretreatment system along with built-in back wash provision and remineralisation. The system is designed for heavy duty tasks in order to withstand frequent relocation from site to site and in skid patterns for portable transportation via road upon requirement. The conceptual design of the plant is over. The design and constructional aspects of the mobile plant are elaborated in this paper. (author)

The Pitfalls of Mobile Devices in Learning: A Different View and Implications for Pedagogical Design

Science.gov (United States)

Ting, Yu-Liang

2012-01-01

Studies have been devoted to the design, implementation, and evaluation of mobile learning in practice. A common issue among students' responses toward this type of learning concerns the pitfalls of mobile devices, including small screen, limited input options, and low computational power. As a result, mobile devices are not always perceived by…

A cloud-based X73 ubiquitous mobile healthcare system: design and implementation.

Science.gov (United States)

Ji, Zhanlin; Ganchev, Ivan; O'Droma, Máirtín; Zhang, Xin; Zhang, Xueji

2014-01-01

Based on the user-centric paradigm for next generation networks, this paper describes a ubiquitous mobile healthcare (uHealth) system based on the ISO/IEEE 11073 personal health data (PHD) standards (X73) and cloud computing techniques. A number of design issues associated with the system implementation are outlined. The system includes a middleware on the user side, providing a plug-and-play environment for heterogeneous wireless sensors and mobile terminals utilizing different communication protocols and a distributed "big data" processing subsystem in the cloud. The design and implementation of this system are envisaged as an efficient solution for the next generation of uHealth systems.

Dual-Gate p-GaN Gate High Electron Mobility Transistors for Steep Subthreshold Slope.

Science.gov (United States)

Bae, Jong-Ho; Lee, Jong-Ho

2016-05-01

A steep subthreshold slope characteristic is achieved through p-GaN gate HEMT with dual-gate structure. Obtained subthreshold slope is less than 120 μV/dec. Based on the measured and simulated data obtained from single-gate device, breakdown of parasitic floating-base bipolar transistor and floating gate charged with holes are responsible to increase abruptly in drain current. In the dual-gate device, on-current degrades with high temperature but subthreshold slope is not changed. To observe the switching speed of dual-gate device and transient response of drain current are measured. According to the transient responses of drain current, switching speed of the dual-gate device is about 10(-5) sec.

Dual-camera design for coded aperture snapshot spectral imaging.

Science.gov (United States)

Wang, Lizhi; Xiong, Zhiwei; Gao, Dahua; Shi, Guangming; Wu, Feng

2015-02-01

Coded aperture snapshot spectral imaging (CASSI) provides an efficient mechanism for recovering 3D spectral data from a single 2D measurement. However, since the reconstruction problem is severely underdetermined, the quality of recovered spectral data is usually limited. In this paper we propose a novel dual-camera design to improve the performance of CASSI while maintaining its snapshot advantage. Specifically, a beam splitter is placed in front of the objective lens of CASSI, which allows the same scene to be simultaneously captured by a grayscale camera. This uncoded grayscale measurement, in conjunction with the coded CASSI measurement, greatly eases the reconstruction problem and yields high-quality 3D spectral data. Both simulation and experimental results demonstrate the effectiveness of the proposed method.

System perspectives for mobile platform design in m-Health

Science.gov (United States)

Roveda, Janet M.; Fink, Wolfgang

2016-05-01

Advances in integrated circuit technologies have led to the integration of medical sensor front ends with data processing circuits, i.e., mobile platform design for wearable sensors. We discuss design methodologies for wearable sensor nodes and their applications in m-Health. From the user perspective, flexibility, comfort, appearance, fashion, ease-of-use, and visibility are key form factors. From the technology development point of view, high accuracy, low power consumption, and high signal to noise ratio are desirable features. From the embedded software design standpoint, real time data analysis algorithms, application and database interfaces are the critical components to create successful wearable sensor-based products.

Mobile Disdrometer Observations of Nocturnal Mesoscale Convective Systems During PECAN

Science.gov (United States)

Bodine, D. J.; Rasmussen, K. L.

2015-12-01

Understanding microphysical processes in nocturnal mesoscale convective systems (MCSs) is an important objective of the Plains Elevated Convection At Night (PECAN) experiment, which occurred from 1 June - 15 July 2015 in the central Great Plains region of the United States. Observations of MCSs were collected using a large array of mobile and fixed instrumentation, including ground-based radars, soundings, PECAN Integrated Sounding Arrays (PISAs), and aircraft. In addition to these observations, three mobile Parsivel disdrometers were deployed to obtain drop-size distribution (DSD) measurements to further explore microphysical processes in convective and stratiform regions of nocturnal MCSs. Disdrometers were deployed within close range of a multiple frequency network of mobile and fixed dual-polarization radars (5 - 30 km range), and near mobile sounding units and PISAs. Using mobile disdrometer and multiple-wavelength, dual-polarization radar data, microphysical properties of convective and stratiform regions of MCSs are investigated. The analysis will also examine coordinated Range-Height Indicator (RHI) scans over the disdrometers to elucidate vertical DSD structure. Analysis of dense observations obtained during PECAN in combination with mobile disdrometer DSD measurements contributes to a greater understanding of the structural characteristics and evolution of nocturnal MCSs.

Design of dual energy x-ray detector for conveyor belt with steel wire ropes

Science.gov (United States)

Dai, Yue; Miao, Changyun; Rong, Feng

2009-07-01

A dual energy X-ray detector for conveyor belt with steel wire ropes is researched in the paper. Conveyor belt with steel wire ropes is one of primary transfer equipments in modern production. The traditional test methods like electromagnetic induction principle could not display inner image of steel wire ropes directly. So X-ray detection technology has used to detect the conveyor belt. However the image was not so clear by the interference of the rubber belt. Therefore, the dualenergy X-ray detection technology with subtraction method is developed to numerically remove the rubber belt from radiograph, thus improving the definition of the ropes image. The purpose of this research is to design a dual energy Xray detector that could make the operator easier to found the faulty of the belt. This detection system is composed of Xray source, detector controlled by FPGA chip, PC for running image processing system and so on. With the result of the simulating, this design really improved the capability of the staff to test the conveyor belt.

Age-related differences in dual task performance: A cross-sectional study on women.

Science.gov (United States)

Brustio, Paolo R; Magistro, Daniele; Rabaglietti, Emanuela; Liubicich, Monica E

2017-02-01

Simultaneous performances of motor and attention-demanding tasks are common in activities of everyday life. The present cross-sectional study examined the changes and age-related differences on mobility performance with an additional cognitive or motor task, and evaluated the relative dual-task cost (DTC) on the motor performance in young, middle-aged and older women. A total of 30 young (mean age 25.12 ± 3.00 years), 30 middle-aged (mean age 47.82 ± 5.06 years) and 30 older women (mean age 72.74 ± 5.95 years) were recruited. Participants carried out: (i) single task: Timed Up & Go Test; (ii) cognitive dual-task: Timed Up & Go Test while counting backwards by three; (iii) manual dual-task: Timed Up & Go Test while carrying a glass of water. A repeated measures anova with between-factor as age groups and within-factor as tasks was carried out to assess the effect of aging on the performance of mobility tasks. DTC was calculated as ([performance in single-task - performance in dual-task] / performance in single task) × 100%. One-way ancova were carried out to compare the DTC among the three age groups. A significant interaction between age groups and task (F 4,172  = 6.716, P performance under dual-task condition compared with young and middle-aged groups. Furthermore, DTC differences in cognitive task were observed in older women compared with younger and middle-aged women (F 2,86  = 7.649, P task. Dual-task conditions might affect mobility performance differently across the lifespan, and could be particularly challenging in older women. Geriatr Gerontol Int 2017; 17: 315-321. © 2015 Japan Geriatrics Society.

Theory and application of dual-transistor charge separation analysis

International Nuclear Information System (INIS)

Fleetwood, D.M.; Schwank, J.R.; Winokur, P.S.; Sexton, F.W.; Shaneyfelt, M.R.

1989-01-01

The authors describe a dual-transistor charge separation method to evaluate the radiation response of MOS transistors. This method requires that n- and p-channel transistors with identically processed oxides be irradiated under identical conditions at the same oxide electric fields. Combining features of single-transistor midgap and mobility methods, the authors show how one may determine threshold voltage shifts due to oxide-trapped and interface-trapped charge from standard threshold voltage and mobility measurements. These measurements can be made at currents 2-5 orders of magnitude higher than those required for midgap, subthreshold slope, and charge-pumping methods. The dual-transistor method contains no adjustable parameters, and includes an internal self-consistency check. The accuracy of the method is verified by comparison to midgap, subthreshold slope, and charge-pumping methods for several MOS processes and technologies

Guidance Law Design for a Class of Dual-Spin Mortars

Directory of Open Access Journals (Sweden)

Qing-wei Guo

2015-01-01

Full Text Available To minimize the cost and maximize the ease of use, a class of dual-spin mortars is designed which only rely on GPS receiver and geomagnetic measurements. However, there are some problems to be solved when the range is small, such as low correction authority and trajectory bending. Guidance law design for this mortar is detailed. Different guidance laws were designed for the ascending and descending segments, respectively. By taking variable parameter guidance law in the vertical plane and using compensation in the lateral plane, the problems mentioned above were resolved. Roll angle resolving algorithms with geomagnetic measurements were demonstrated and the experiment results proved to be effective. In order to verify the effectiveness, Seven-Degrees-of-Freedom (7-DOF rigid ballistic model were established and hardware in the loop simulation was introduced. After the transform function of the actuator was obtained, the control model of the shell was improved. The results of the Monte Carlo simulation demonstrate that the guidance law is suitable and the mortar can be effectively controlled.

A Smart Mobile Lab-on-Chip-Based Medical Diagnostics System Architecture Designed For Evolvability

DEFF Research Database (Denmark)

Patou, François; Dimaki, Maria; Svendsen, Winnie Edith

2015-01-01

for this work. We introduce a smart-mobile and LoC-based system architecture designed for evolvability. By propagating LoC programmability, instrumentation, and control tools to the highlevel abstraction smart-mobile software layer, our architecture facilitates the realisation of new use...

Functional Mobility Testing: A Novel Method to Establish Human System Interface Design Requirements

Science.gov (United States)

England, Scott A.; Benson, Elizabeth A.; Rajulu, Sudhakar

2008-01-01

Across all fields of human-system interface design it is vital to posses a sound methodology dictating the constraints on the system based on the capabilities of the human user. These limitations may be based on strength, mobility, dexterity, cognitive ability, etc. and combinations thereof. Data collected in an isolated environment to determine, for example, maximal strength or maximal range of motion would indeed be adequate for establishing not-to-exceed type design limitations, however these restraints on the system may be excessive over what is basally needed. Resources may potentially be saved by having a technique to determine the minimum measurements a system must accommodate. This paper specifically deals with the creation of a novel methodology for establishing mobility requirements for a new generation of space suit design concepts. Historically, the Space Shuttle and the International Space Station vehicle and space hardware design requirements documents such as the Man-Systems Integration Standards and International Space Station Flight Crew Integration Standard explicitly stated that the designers should strive to provide the maximum joint range of motion capabilities exhibited by a minimally clothed human subject. In the course of developing the Human-Systems Integration Requirements (HSIR) for the new space exploration initiative (Constellation), an effort was made to redefine the mobility requirements in the interest of safety and cost. Systems designed for manned space exploration can receive compounded gains from simplified designs that are both initially less expensive to produce and lighter, thereby, cheaper to launch.

Sliders Versus Storyboards - Investigating Interaction Design for Mobile Video Browsing

NARCIS (Netherlands)

Hürst, Wolfgang|info:eu-repo/dai/nl/313710589; Hoet, Miklas

2015-01-01

We present a comparative study of two different interfaces for mobile video browsing on tablet devices following two basic concepts - storyboard designs representing a video’s content in a grid-like arrangement of static images extracted from the file, and slider interfaces enabling users to

Predicted accommodative response from image quality in young eyes fitted with different dual-focus designs.

Science.gov (United States)

Faria-Ribeiro, Miguel; Amorim-de-Sousa, Ana; González-Méijome, José M

2018-05-01

To investigate the separated and combined influences of inner zone (IZ) diameter and effective add power of dual-focus contact lenses (CL) in the image quality at distance and near viewing, in a functional accommodating model eye. Computational wave-optics methods were used to define zonal bifocal pupil functions, representing the optic zones of nine dual-focus centre-distance CLs. The dual-focus pupil functions were defined having IZ diameters of 2.10 mm, 3.36 mm and 4.00 mm, with add powers of 1.5 D, 2.0 D and 2.5 D (dioptres), for each design, that resulted in a ratio of 64%/36% between the distance and treatment zone areas, bounded by a 6 mm entrance pupil. A through-focus routine was implemented in MATLAB to simulate the changes in image quality, calculated from the Visual Strehl ratio, as the eye with the dual-focus accommodates, from 0 to -3.00 D target vergences. Accommodative responses were defined as the changes in the defocus coefficient, combined with a change in fourth and sixth order spherical aberration, which produced a peak in image quality at each target vergence. Distance viewing image quality was marginally affected by IZ diameter but not by add power. Near image quality obtained when focussing the image formed by the near optics was only higher by a small amount compared to the other two IZ diameters. The mean ± standard deviation values obtained with the three adds were 0.28 ± 0.02, 0.23 ± 0.02 and 0.22 ± 0.02, for the small, medium and larger IZ diameters, respectively. On the other hand, near image quality predicted by focussing the image formed by the distance optics was considerably lower relatively to the other two IZ diameters. The mean ± standard deviation values obtained with the three adds were 0.15 ± 0.01, 0.38 ± 0.00 and 0.54 ± 0.01, for the small, medium and larger IZ diameters, respectively. During near viewing through dual-focus CLs, image quality depends on the diameter of the most inner zone of the CL, while add power

The Neurocognitive Basis for Impaired Dual-Task Performance in Senior Fallers.

Science.gov (United States)

Nagamatsu, Lindsay S; Hsu, C Liang; Voss, Michelle W; Chan, Alison; Bolandzadeh, Niousha; Handy, Todd C; Graf, Peter; Beattie, B Lynn; Liu-Ambrose, Teresa

2016-01-01

Falls are a major health-care concern, and while dual-task performance is widely recognized as being impaired in those at-risk for falls, the underlying neurocognitive mechanisms remain unknown. A better understanding of the underlying mechanisms could lead to the refinement and development of behavioral, cognitive, or neuropharmacological interventions for falls prevention. Therefore, we conducted a cross-sectional study with community-dwelling older adults aged 70-80 years with a history of falls (i.e., two or more falls in the past 12 months) or no history of falls (i.e., zero falls in the past 12 months); n = 28 per group. We compared functional activation during cognitive-based dual-task performance between fallers and non-fallers using functional magnetic resonance imaging (fMRI). Executive cognitive functioning was assessed via Stroop, Trail Making, and Digit Span. Mobility was assessed via the Timed Up and Go test (TUG). We found that non-fallers exhibited significantly greater functional activation compared with fallers during dual-task performance in key regions responsible for resolving dual-task interference, including precentral, postcentral, and lingual gyri. Further, we report slower reaction times during dual-task performance in fallers and significant correlations between level of functional activation and independent measures of executive cognitive functioning and mobility. Our study is the first neuroimaging study to examine dual-task performance in fallers, and supports the notion that fallers have reduced functional brain activation compared with non-fallers. Given that dual-task performance-and the underlying neural concomitants-appears to be malleable with relevant training, our study serves as a launching point for promising strategies to reduce falls in the future.

Design of an MSAT-X mobile transceiver and related base and gateway stations

Science.gov (United States)

Fang, Russell J. F.; Bhaskar, Udaya; Hemmati, Farhad; Mackenthun, Kenneth M.; Shenoy, Ajit

This paper summarizes the results of a design study of the mobile transceiver, base station, and gateway station for NASA's proposed Mobile Satellite Experiment (MSAT-X). Major ground segment system design issues such as frequency stability control, modulation method, linear predictive coding vocoder algorithm, and error control technique are addressed. The modular and flexible transceiver design is described in detail, including the core, RF/IF, modem, vocoder, forward error correction codec, amplitude-companded single sideband, and input/output modules, as well as the flexible interface. Designs for a three-carrier base station and a 10-carrier gateway station are also discussed, including the interface with the controllers and with the public-switched telephone networks at the gateway station. Functional specifications are given for the transceiver, the base station, and the gateway station.

Design of an MSAT-X mobile transceiver and related base and gateway stations

Science.gov (United States)

Fang, Russell J. F.; Bhaskar, Udaya; Hemmati, Farhad; Mackenthun, Kenneth M.; Shenoy, Ajit

1987-01-01

This paper summarizes the results of a design study of the mobile transceiver, base station, and gateway station for NASA's proposed Mobile Satellite Experiment (MSAT-X). Major ground segment system design issues such as frequency stability control, modulation method, linear predictive coding vocoder algorithm, and error control technique are addressed. The modular and flexible transceiver design is described in detail, including the core, RF/IF, modem, vocoder, forward error correction codec, amplitude-companded single sideband, and input/output modules, as well as the flexible interface. Designs for a three-carrier base station and a 10-carrier gateway station are also discussed, including the interface with the controllers and with the public-switched telephone networks at the gateway station. Functional specifications are given for the transceiver, the base station, and the gateway station.

An ARM Mobile Facility Designed for Marine Deployments

Science.gov (United States)

Wiscombe, W. J.

2007-05-01

The U.S. Dept. of Energy's ARM (Atmospheric Radiation Measurements) Program is designing a Mobile Facility exclusively for marine deployments. This marine facility is patterned after ARM's land Mobile Facility, which had its inaugural deployment at Point Reyes, California, in 2005, followed by deployments to Niger in 2006 and Germany in 2007 (ongoing), and a planned deployment to China in 2008. These facilities are primarily intended for the study of clouds, radiation, aerosols, and surface processes with a goal to include these processes accurately in climate models. They are preferably embedded within larger field campaigns which provide context. They carry extensive instrumentation (in several large containers) including: cloud radar, lidar, microwave radiometers, infrared spectrometers, broadband and narrowband radiometers, sonde-launching facilities, extensive surface aerosol measurements, sky imagers, and surface latent and sensible heat flux devices. ARM's Mobile Facilities are designed for 6-10 month deployments in order to capture climatically-relevant datasets. They are available to any scientist, U.S. or international, who wishes to submit a proposal during the annual Spring call. The marine facility will be adapted to, and ruggedized for, the harsh marine environment and will add a scanning two-frequency radar, a boundary-layer wind profiler, a shortwave spectrometer, and aerosol instrumentation adapted to typical marine aerosols like sea salt. Plans also include the use of roving small UAVs, automated small boats, and undersea autonomous vehicles in order to address the point-to-area-average problem which is so crucial for informing climate models. Initial deployments are planned for small islands in climatically- interesting cloud regimes, followed by deployments on oceanic platforms (like decommissioned oil rigs and the quasi-permanent platform of this session's title) and eventually on large ships like car carriers plying routine routes.

Usability principles to design mobile workplace learning content

Directory of Open Access Journals (Sweden)

Alessia Messuti

2015-04-01

Full Text Available The article describes the design of a mobile workplace learning tool for trainers of the International Training Centre of the International Labour Organization. The motivation behind is to provide trainers with a practical tool that will enable them to recall information at the moment of need and continue to learn in context. On this purpose a set of visual augmented reality cards was created, taking into consideration the fundamental mobile learning and usability principles. The nature of the article is empirical as it reports an experiment carried out with trainers which aimed at testing cards usability and learnability. Results show that the integration of both online and offline strategies was perceived as an added value as trainers could choose to retrieve information as they mostly like; finally, it also resulted in high usability scores, an aspect that contributes to their effectiveness at the workplace.

Mobile Traffic Alert and Tourist Route Guidance System Design Using Geospatial Data

Science.gov (United States)

Bhattacharya, D.; Painho, M.; Mishra, S.; Gupta, A.

2017-09-01

The present study describes an integrated system for traffic data collection and alert warning. Geographical information based decision making related to traffic destinations and routes is proposed through the design. The system includes a geospatial database having profile relating to a user of a mobile device. The processing and understanding of scanned maps, other digital data input leads to route guidance. The system includes a server configured to receive traffic information relating to a route and location information relating to the mobile device. Server is configured to send a traffic alert to the mobile device when the traffic information and the location information indicate that the mobile device is traveling toward traffic congestion. Proposed system has geospatial and mobile data sets pertaining to Bangalore city in India. It is envisaged to be helpful for touristic purposes as a route guidance and alert relaying information system to tourists for proximity to sites worth seeing in a city they have entered into. The system is modular in architecture and the novelty lies in integration of different modules carrying different technologies for a complete traffic information system. Generic information processing and delivery system has been tested to be functional and speedy under test geospatial domains. In a restricted prototype model with geo-referenced route data required information has been delivered correctly over sustained trials to designated cell numbers, with average time frame of 27.5 seconds, maximum 50 and minimum 5 seconds. Traffic geo-data set trials testing is underway.

Wide frequency independently controlled dual-band inkjet-printed antenna

KAUST Repository

AbuTarboush, Hattan F.; Shamim, Atif

2014-01-01

.2 and 23.7%, respectively. These dual-bands have the ability to be controlled independently between 1.1 and 7.5 GHz without affecting the other band. In addition, the proposed antenna can be assigned for different mobile and wireless applications

Shed a light of wireless technology on portable mobile design of NIRS

Science.gov (United States)

Sun, Yunlong; Li, Ting

2016-03-01

Mobile internet is growing rapidly driven by high-tech companies including the popular Apple and Google. The wireless mini-NIRS is believed to deserve a great spread future, while there is sparse report on wireless NIRS device and even for the reported wireless NIRS, its wireless design is scarcely presented. Here we focused on the wireless design of NIRS devices. The widely-used wireless communication standards and wireless communication typical solutions were employed into our NIRS design and then compared on communication efficiency, distance, error rate, low-cost, power consumption, and stabilities, based on the requirements of NIRS applications. The properly-performed wireless communication methods matched with the characteristics of NIRS are picked out. Finally, we realized one recommended wireless communication in our NIRS, developed a test platform on wireless NIRS and tested the full properties on wireless communication. This study elaborated the wireless communication methods specified for NIRS and suggested one implementation with one example fully illustrated, which support the future mobile design on NIRS devices.

New Fukui, dual and hyper-dual kernels as bond reactivity descriptors.

Science.gov (United States)

Franco-Pérez, Marco; Polanco-Ramírez, Carlos-A; Ayers, Paul W; Gázquez, José L; Vela, Alberto

2017-06-21

We define three new linear response indices with promising applications for bond reactivity using the mathematical framework of τ-CRT (finite temperature chemical reactivity theory). The τ-Fukui kernel is defined as the ratio between the fluctuations of the average electron density at two different points in the space and the fluctuations in the average electron number and is designed to integrate to the finite-temperature definition of the electronic Fukui function. When this kernel is condensed, it can be interpreted as a site-reactivity descriptor of the boundary region between two atoms. The τ-dual kernel corresponds to the first order response of the Fukui kernel and is designed to integrate to the finite temperature definition of the dual descriptor; it indicates the ambiphilic reactivity of a specific bond and enriches the traditional dual descriptor by allowing one to distinguish between the electron-accepting and electron-donating processes. Finally, the τ-hyper dual kernel is defined as the second-order derivative of the Fukui kernel and is proposed as a measure of the strength of ambiphilic bonding interactions. Although these quantities have never been proposed, our results for the τ-Fukui kernel and for τ-dual kernel can be derived in zero-temperature formulation of the chemical reactivity theory with, among other things, the widely-used parabolic interpolation model.

Career Mobility: Does Gender Matter?

Science.gov (United States)

Bell, Rose R.

1992-01-01

A study examined attitudes of 95 women biomedical researchers in dual-career relationships toward mobility for enhancing occupational advancement. The women and spouses were surveyed concerning use of time, income, job satisfaction, willingness to move, and general career and marital satisfaction. Results indicate changes in gender effects on…

A 5.2/5.8 GHz Dual Band On-Off Keying Transmitter Design for Bio-Signal Transmission

Science.gov (United States)

Wu, Chang-Hsi; You, Hong-Cheng; Huang, Shun-Zhao

2018-02-01

An architecture of 5.2/5.8-GHz dual-band on-off keying (DBOOK) modulated transmitter is designed in a 0.18-μm CMOS technology. The proposed DBOOK transmitter is used in the biosignal transmission system with high power efficiency and small area. To reduce power consumption and enhance output swing, two pairs of center-tapped transformers are used as both LC tank and source grounding choke for the designed voltage controlled oscillator (VCO). Switching capacitances are used to achieve dual band operations, and a complemented power combiner is used to merge the differential output power of VCO to a single-ended output. Besides, the linearizer circuits are used in the proposed power amplifier with wideband output matching to improve the linearity both at 5.2/5.8-GHz bands. The designed DBOOK transmitter is implemented by dividing it into two chips. One chip implements the dual-band switching VCO and power combiner, and the other chip implements a linear power amplifier including dual-band operation. The first chip drives an output power of 2.2mW with consuming power of 5.13 mW from 1.1 V supply voltage. With the chip size including pad of 0.61 × 0.91 m2, the measured data rate and transmission efficiency attained are 100 Mb/s and 51 pJ/bit, respectively. The second chip, for power enhanced mode, exhibits P1 dB of -9 dBm, IIP3 of 1 dBm, the output power 1 dB compression point of 12.42 dBm, OIP3 of about 21 dBm, maximum output power of 17.02/16.18 dBm, and power added efficiency of 17.13/16.95% for 5.2/ 5.8 GHz. The chip size including pads is 0:693 × 1:084mm2.

Designing a Mobile Game to Teach Conceptual Knowledge of Avoiding 'Phishing Attacks'

OpenAIRE

Asanka, Nalin; Love, Steve; Scott, Michael

2012-01-01

Phishing is a form of online identity theft, which attempts to appropriate confidential and sensitive information such as usernames and passwords from its victims. To facilitate cyberspace as a secure environment, phishing education needs to be made accessible to home computer users and mobile games enable embedded learning in a natural environment. Previously, we have introduced a mobile game design that aimed to enhance avoidance motivation and behavior to protect against phishing threats. ...

A user-centered model for designing consumer mobile health (mHealth) applications (apps).

Science.gov (United States)

Schnall, Rebecca; Rojas, Marlene; Bakken, Suzanne; Brown, William; Carballo-Dieguez, Alex; Carry, Monique; Gelaude, Deborah; Mosley, Jocelyn Patterson; Travers, Jasmine

2016-04-01

Mobile technologies are a useful platform for the delivery of health behavior interventions. Yet little work has been done to create a rigorous and standardized process for the design of mobile health (mHealth) apps. This project sought to explore the use of the Information Systems Research (ISR) framework as guide for the design of mHealth apps. Our work was guided by the ISR framework which is comprised of 3 cycles: Relevance, Rigor and Design. In the Relevance cycle, we conducted 5 focus groups with 33 targeted end-users. In the Rigor cycle, we performed a review to identify technology-based interventions for meeting the health prevention needs of our target population. In the Design Cycle, we employed usability evaluation methods to iteratively develop and refine mock-ups for a mHealth app. Through an iterative process, we identified barriers and facilitators to the use of mHealth technology for HIV prevention for high-risk MSM, developed 'use cases' and identified relevant functional content and features for inclusion in a design document to guide future app development. Findings from our work support the use of the ISR framework as a guide for designing future mHealth apps. Results from this work provide detailed descriptions of the user-centered design and system development and have heuristic value for those venturing into the area of technology-based intervention work. Findings from this study support the use of the ISR framework as a guide for future mHealth app development. Use of the ISR framework is a potentially useful approach for the design of a mobile app that incorporates end-users' design preferences. Copyright © 2016 Elsevier Inc. All rights reserved.

A Vehicular Mobile Standard Instrument for Field Verification of Traffic Speed Meters Based on Dual-Antenna Doppler Radar Sensor.

Science.gov (United States)

Du, Lei; Sun, Qiao; Cai, Changqing; Bai, Jie; Fan, Zhe; Zhang, Yue

2018-04-05

Traffic speed meters are important legal measuring instruments specially used for traffic speed enforcement and must be tested and verified in the field every year using a vehicular mobile standard speed-measuring instrument to ensure speed-measuring performances. The non-contact optical speed sensor and the GPS speed sensor are the two most common types of standard speed-measuring instruments. The non-contact optical speed sensor requires extremely high installation accuracy, and its speed-measuring error is nonlinear and uncorrectable. The speed-measuring accuracy of the GPS speed sensor is rapidly reduced if the amount of received satellites is insufficient enough, which often occurs in urban high-rise regions, tunnels, and mountainous regions. In this paper, a new standard speed-measuring instrument using a dual-antenna Doppler radar sensor is proposed based on a tradeoff between the installation accuracy requirement and the usage region limitation, which has no specified requirements for its mounting distance and no limitation on usage regions and can automatically compensate for the effect of an inclined installation angle on its speed-measuring accuracy. Theoretical model analysis, simulated speed measurement results, and field experimental results compared with a GPS speed sensor with high accuracy showed that the dual-antenna Doppler radar sensor is effective and reliable as a new standard speed-measuring instrument.

An Optimal Design of Multiple Antenna Positions on Mobile Devices Based on Mutual Coupling Analysis

Directory of Open Access Journals (Sweden)

Peerapong Uthansakul

2011-01-01

Full Text Available The topic of practical implementation of multiple antenna systems for mobile communications has recently gained a lot of attention. Due to the area constraint on a mobile device, the problem of how to design such a system in order to achieve the best benefit is still a huge challenge. In this paper, genetic algorithm (GA is used to find the optimal antenna positions on a mobile device. Two cases of 3×3 and 4×4 MIMO systems are undertaken. The effect of mutual coupling based on Z-parameter is the main factor to determine the MIMO capacity concerning the objective function of GA search. The results confirm the success of the proposed method to design MIMO antenna positions on a mobile device. Moreover, this paper introduces the method to design the antenna positions for the condition of nondeterministic channel. The concern of channel variation has been included in the process of finding optimal MIMO antenna positions. The results suggest that the averaging position from all GA solutions according to all channel conditions provides the most acceptable benefit.

Feasibility of a dual regime gyrotron

International Nuclear Information System (INIS)

Sawant, Ashwini; Jain, Prerit; Kartikeyan, M.V.

2012-01-01

The design concept of a 42/84 GHz, 500 kW, CW, dual-regime gyrotron for ECRH of plasma in an experimental Tokamak will be presented in this paper. Operation at 42 GHz is fundamental where as that in 84 GHz will be second harmonic so that a similar guidance system will be retained for dual regime operation. In this paper, the mode competition and mode selection procedures are presented for such a dual regime operation. Cold cavity design and self-consistent calculations will be carried out for power and efficiencies. (author)

Low friction arthroplasty and dual mobility cup: a new gold standard.

Science.gov (United States)

Prudhon, Jean Louis; Verdier, Régis; Caton, Jacques H

2017-03-01

Low friction arthroplasty (LFA) introduced by Sir John Charnley was the gold standard for many years. Dislocation and infection are the first causes for early revision. Late failures are polyethylene (PE) wear and loosening. Due to dislocation risk we slowly switched to the use of LFA with dual mobility cups (DMC). The purposes of this study are (1) to assess whether our changes have improved outcomes and (2) what is the new gold standard? We selected from an observational registry of 1,091 cases of hybrid Charnley total hip arthroplasty (THA). The acetabular component was either DMC in 455 cases or fixed cup (FC) in 636 cases. Three dislocations (0.6%) occurred in the DMC group (none revised). In the FC group 54 dislocated (8.49%) and 20 were recurrent and underwent revision (revision rate 3.14%). In the DMC group, five acetabular and three femoral revisions were performed (revision rate for loosening 1.7%). In the FC group 19 cases underwent acetabular revision, and five cases had femoral component revised (revision rate for loosening 3.7%). Charnley's LFA has proven over 50 years of excellent survivorship. To decrease dislocation risk, one suggested increasing femoral head diameter. Gilles Bousquet proposed another way, namely, the DMC concept. Dislocation is no longer a critical issue with DMC as demonstrated in our series and main series. DMC in primary THA is still a subject of debate. Mid-term results do not demonstrate a higher rate of wear than LFA. What is the current gold standard? LFA was and is our current gold standard in association with a DMC.

Designing dual inhibitors of Mdm2/MdmX: Unexpected coupling of water with gatekeeper Y100/99.

Science.gov (United States)

Lee, Xiong An; Verma, Chandra; Sim, Adelene Y L

2017-08-01

Mdm2 and MdmX share high structural similarity in their N-terminal domains, yet dual inhibitors are challenging to design due to differences in the conformations of the binding pockets, and notably of the proposed gatekeeper residue, Y100/99. Analysis of crystal structures and molecular dynamics (MD) simulations of complexes of Mdm2 and MdmX resulted in the identification of a water molecule with a long residence time that appears to be modulated by the conformation of Y100/99. These observations lead us to speculate that dual inhibitors either (i) stabilize both Mdm2 and MdmX with Y100/99 in the open conformation typically seen in complexes of Mdm2 with p53, or (ii) the dual inhibitors are agnostic to the conformation of Y100/99. The recently developed potent dual inhibitory stapled peptide Atsp7041 appears to be agnostic to the conformation of the gatekeeper residue. Proteins 2017; 85:1493-1506. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Mobile Semiotics - signs and mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

a potential for mobilities studies if the awareness of seeing the environment as a semiotic layer and system can be sensitized to the insights of the ‘mobilities turn’. Empirically the paper tentatively explores the usefulness of a mobile semiotics approach to cases such as street signage, airport design...

Older Adults Pay an Additional Cost When Texting and Walking: Effects of Age, Environment, and Use of Mixed Reality on Dual-Task Performance.

Science.gov (United States)

Krasovsky, Tal; Weiss, Patrice L; Kizony, Rachel

2018-04-06

Texting while walking (TeWW) has become common among people of all ages, and mobile phone use during gait is increasingly associated with pedestrian injury. Although dual-task walking performance is known to decline with age, data regarding the effect of age on dual-task performance in ecological settings are limited. The objective of this study was to evaluate the effect of age, environment (indoors/outdoors), and mixed reality (merging of real and virtual environments) on TeWW performance. A cross-sectional design was used. Young (N = 30; 27.8 ± 4.4 years) and older (N = 20; 68.9 ± 3.9 years) adults performed single and dual-task texting and walking indoors and outdoors, with and without a mixed reality display. Participants also completed evaluations of visual scanning and cognitive flexibility (Trail Making Test) and functional mobility (Timed Up and Go). Indoors, similar interference to walking and texting occurred for both groups, but only older adults' gait variability increased under dual task conditions. Outdoors, TeWW was associated with larger age-related differences in gait variability, texting accuracy, and gait dual-task costs. Young adults with better visual scanning and cognitive flexibility performed TeWW with lower gait costs (r = 0.52 to r = 0.65). The mixed reality display was unhelpful and did not modify walking or texting. Older adults tested in this study were relatively high-functioning. Gaze of participants was not directly monitored. Although young and older adults possess the resources necessary for TeWW, older adults pay an additional "price" when dual-tasking, especially outdoors. TeWW may have potential as an ecologically-valid assessment and/or an intervention paradigm for dual task performance among older adults as well as for clinical populations.

The Design and Analysis of Virtual Network Configuration for a Wireless Mobile ATM Network

OpenAIRE

Bush, Stephen F.

1999-01-01

This research concentrates on the design and analysis of an algorithm referred to as Virtual Network Configuration (VNC) which uses predicted future states of a system for faster network configuration and management. VNC is applied to the configuration of a wireless mobile ATM network. VNC is built on techniques from parallel discrete event simulation merged with constraints from real-time systems and applied to mobile ATM configuration and handoff. Configuration in a mobile network is a dyna...

Students’ Preferences And Opinions On Design 
Of A Mobile Marketing Education Application

Directory of Open Access Journals (Sweden)

F. Zeynep OZATA

2014-01-01

Full Text Available The purpose of this study was to define and better understand business school students’ opinions and preferences on the design of a mobile marketing education application. To accomplish this purpose an explanatory mixed methods study design was used and the data was collected sequentially. First, a questionnaire was conducted with 168 business school students from Anadolu University to define their learning styles. The learning orientation questionnaire produced five factors: visual, auditory, dependent, collaborative, and reading & writing learning styles. In the second phase of the study, semi-structured in depth interviews were conducted with nine graduate students at Anadolu University to better understand their preferences and explore their opinions on the mobile application. After the coding process three themes emerged: learning styles, content, and tools. Added to these themes, eight motives for the use of a mobile marketing education application were also identified.

MOBILE TRAFFIC ALERT AND TOURIST ROUTE GUIDANCE SYSTEM DESIGN USING GEOSPATIAL DATA

Directory of Open Access Journals (Sweden)

D. Bhattacharya

2017-09-01

Full Text Available The present study describes an integrated system for traffic data collection and alert warning. Geographical information based decision making related to traffic destinations and routes is proposed through the design. The system includes a geospatial database having profile relating to a user of a mobile device. The processing and understanding of scanned maps, other digital data input leads to route guidance. The system includes a server configured to receive traffic information relating to a route and location information relating to the mobile device. Server is configured to send a traffic alert to the mobile device when the traffic information and the location information indicate that the mobile device is traveling toward traffic congestion. Proposed system has geospatial and mobile data sets pertaining to Bangalore city in India. It is envisaged to be helpful for touristic purposes as a route guidance and alert relaying information system to tourists for proximity to sites worth seeing in a city they have entered into. The system is modular in architecture and the novelty lies in integration of different modules carrying different technologies for a complete traffic information system. Generic information processing and delivery system has been tested to be functional and speedy under test geospatial domains. In a restricted prototype model with geo-referenced route data required information has been delivered correctly over sustained trials to designated cell numbers, with average time frame of 27.5 seconds, maximum 50 and minimum 5 seconds. Traffic geo-data set trials testing is underway.

Mobile Lexicography

DEFF Research Database (Denmark)

Køhler Simonsen, Henrik

2014-01-01

Users are already mobile, but the question is to which extent knowledge-based dictionary apps are designed for the mobile user situation. The objective of this article is to analyse the characteristics of the mobile user situation and to look further into the stationary user situation and the mob......Users are already mobile, but the question is to which extent knowledge-based dictionary apps are designed for the mobile user situation. The objective of this article is to analyse the characteristics of the mobile user situation and to look further into the stationary user situation...... and the mobile user situation. The analysis is based on an empirical survey involving ten medical doctors and a monolingual app designed to support cognitive lexicographic functions, cf. (Tarp 2006:61-64). In test A the doctors looked up five medical terms while sitting down at a desk and in test B the doctors...

Students' Preferences and Opinions on Design of a Mobile Marketing Education Application

Science.gov (United States)

Ozata, Zeynep; Ozdama Keskin, Nilgun

2014-01-01

The purpose of this study was to define and better understand business school students' opinions and preferences on the design of a mobile marketing education application. To accomplish this purpose an explanatory mixed methods study design was used and the data was collected sequentially. First, a questionnaire was conducted with 168 business…

Executive function processes predict mobility outcomes in older adults.

Science.gov (United States)

Gothe, Neha P; Fanning, Jason; Awick, Elizabeth; Chung, David; Wójcicki, Thomas R; Olson, Erin A; Mullen, Sean P; Voss, Michelle; Erickson, Kirk I; Kramer, Arthur F; McAuley, Edward

2014-02-01

To examine the relationship between performance on executive function measures and subsequent mobility outcomes in community-dwelling older adults. Randomized controlled clinical trial. Champaign-Urbana, Illinois. Community-dwelling older adults (N = 179; mean age 66.4). A 12-month exercise trial with two arms: an aerobic exercise group and a stretching and strengthening group. Established cognitive tests of executive function (flanker task, task switching, and a dual-task paradigm) and the Wisconsin card sort test. Mobility was assessed using the timed 8-foot up and go test and times to climb up and down a flight of stairs. Participants completed the cognitive tests at baseline and the mobility measures at baseline and after 12 months of the intervention. Multiple regression analyses were conducted to determine whether baseline executive function predicted postintervention functional performance after controlling for age, sex, education, cardiorespiratory fitness, and baseline mobility levels. Selective baseline executive function measurements, particularly performance on the flanker task (β = 0.15-0.17) and the Wisconsin card sort test (β = 0.11-0.16) consistently predicted mobility outcomes at 12 months. The estimates were in the expected direction, such that better baseline performance on the executive function measures predicted better performance on the timed mobility tests independent of intervention. Executive functions of inhibitory control, mental set shifting, and attentional flexibility were predictive of functional mobility. Given the literature associating mobility limitations with disability, morbidity, and mortality, these results are important for understanding the antecedents to poor mobility function that well-designed interventions to improve cognitive performance can attenuate. © 2014, Copyright the Authors Journal compilation © 2014, The American Geriatrics Society.

Volatile organic compounds discrimination based on dual mode detection

Science.gov (United States)

Yu, Yuanyuan; Wu, Enxiu; Chen, Yan; Feng, Zhihong; Zheng, Shijun; Zhang, Hao; Pang, Wei; Liu, Jing; Zhang, Daihua

2018-06-01

We report on a volatile organic compound (VOC) sensor that can provide concentration-independent signals toward target gases. The device is based on a dual-mode detection mechanism that can simultaneously record the mechanical (resonant frequency, f r) and electrical (current, I) responses of the same gas adsorption event. The two independent signals form a unique I–f r trace for each target VOC as the concentration varies. The mechanical response (frequency shift, Δf r) resulting from mass load on the device is directly related to the amount of surface adsorptions, while the electrical response (current variation, ΔI) is associated with charge transfer across the sensing interface and changes in carrier mobility. The two responses resulting from independent physical processes reflect intrinsic physical properties of each target gas. The ΔI–Δf r trace combined with the concentration dependent frequency (or current) signals can therefore be used to achieve target both recognition and quantification. The dual-mode device is designed and fabricated using standard complementary metal oxide semiconductor (CMOS) compatible processes. It exhibits consistent and stable performance in our tests with six different VOCs including ethanol, methanol, acetone, formaldehyde, benzene and hexane.

Design and multifidelity analysis of dual mode scramjet compression system using coupled NPSS and fluent simulation

Science.gov (United States)

Vijayakumar, Nandakumar

Hypersonic airbreathing engines mark a potential future development of the aerospace industry and immense efforts have been taken in gaining knowledge in them for the past decades. The physical phenomenon occurring at the hypersonic flow regime makes the design and performance prediction of a scramjet engine hard. Though cutting-edge simulation tools fight their way toward accurate prediction of the environment, the time consumed by the entire process in designing and analyzing a scramjet engine and its component may be exorbitant. A multi-fidelity approach for designing a scramjet with a cruising Mach number of 6 is detailed in this research where high-order simulations are applied according to the physics involved in the component. Two state-of-the-art simulation tools were used to take the aerodynamic and propulsion disciplines into account for realistic prediction of the individual components as well as the entire scramjet. The specific goal of this research is to create a virtual environment to design and analyze a hypersonic, two-dimensional, planar inlet and isolator to check its operability for a dual-mode scramjet engine. The dual mode scramjet engine starts at a Mach number of 3.5 where it operates as a ramjet and accelerates to Mach 6 to be operated as a scramjet engine. The intercomponent interaction between the compression components with the rest of the engine is studied by varying the fidelity of the numerical simulation according to the complexity of the situation. Efforts have been taken to track the transition Mach number as it switches from ramjet to scramjet. A complete scramjet assembly was built using the Numerical Propulsion Simulation System (NPSS) and the performance of the engine was evaluated for various scenarios. Different numerical techniques were opted for varying the fidelity of the analysis with the highest fidelity consisting of 2D RANS CFD simulation. The interaction between the NPSS elements with the CFD solver is governed by the

Conceptual Design for a Dual-Bell Rocket Nozzle System Using a NASA F-15 Airplane as the Flight Testbed

Science.gov (United States)

Jones, Daniel S.; Ruf, Joseph H.; Bui, Trong T.; Martinez, Martel; St. John, Clinton W.

2014-01-01

The dual-bell rocket nozzle was first proposed in 1949, offering a potential improvement in rocket nozzle performance over the conventional-bell nozzle. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. In 2013 a proposal was constructed that offered a National Aeronautics and Space Administration (NASA) F-15 airplane as the flight testbed, with the plan to operate a dual-bell rocket nozzle during captive-carried flight. If implemented, this capability will permit nozzle operation into an external flow field similar to that of a launch vehicle, and facilitate an improved understanding of dual-bell nozzle plume sensitivity to external flow-field effects. More importantly, this flight testbed can be utilized to help quantify the performance benefit with the dual-bell nozzle, as well as to advance its technology readiness level. Toward this ultimate goal, this report provides plans for future flights to quantify the external flow field of the airplane near the nozzle experiment, as well as details on the conceptual design for the dual-bell nozzle cold-flow propellant feed system integration within the NASA F-15 Propulsion Flight Test Fixture. The current study shows that this concept of flight research is feasible, and could result in valuable flight data for the dual-bell nozzle.

Mobile health applications to assist patients with diabetes: lessons learned and design implications.

Science.gov (United States)

Årsand, Eirik; Frøisland, Dag Helge; Skrøvseth, Stein Olav; Chomutare, Taridzo; Tatara, Naoe; Hartvigsen, Gunnar; Tufano, James T

2012-09-01

Self-management is critical to achieving diabetes treatment goals. Mobile phones and Bluetooth® can supportself-management and lifestyle changes for chronic diseases such as diabetes. A mobile health (mHealth) research platform--the Few Touch Application (FTA)--is a tool designed to support the self-management of diabetes. The FTA consists of a mobile phone-based diabetes diary, which can be updated both manually from user input and automatically by wireless data transfer, and which provides personalized decision support for the achievement of personal health goals. Studies and applications (apps) based on FTAs have included: (1) automatic transfer of blood glucose (BG) data; (2) short message service (SMS)-based education for type 1diabetes (T1DM); (3) a diabetes diary for type 2 diabetes (T2DM); (4) integrating a patient diabetes diary with health care (HC) providers; (5) a diabetes diary for T1DM; (6) a food picture diary for T1DM; (7) physical activity monitoring for T2DM; (8) nutrition information for T2DM; (9) context sensitivity in mobile self-help tools; and (10) modeling of BG using mobile phones. We have analyzed the performance of these 10 FTA-based apps to identify lessons for designing the most effective mHealth apps. From each of the 10 apps of FTA, respectively, we conclude: (1) automatic BG data transfer is easy to use and provides reassurance; (2) SMS-based education facilitates parent-child communication in T1DM; (3) the T2DM mobile phone diary encourages reflection; (4) the mobile phone diary enhances discussion between patients and HC professionals; (5) the T1DM mobile phone diary is useful and motivational; (6) the T1DM mobile phone picture diary is useful in identifying treatment obstacles; (7) the step counter with automatic data transfer promotes motivation and increases physical activity in T2DM; (8) food information on a phone for T2DM should not be at a detailed level; (9) context sensitivity has good prospects and is possible to

How To Design a Mobile Application to Enhance Teaching and Learning?

Directory of Open Access Journals (Sweden)

Dothang Truong

2014-05-01

Full Text Available The rapid growth of mobile devices, especially smart phones, has changed the way instructors deliver instructions and students learn class materials. Many universities initiate promoting economic transformation by working to eliminate barriers to educational attainment through incorporating new technologies to enhance the delivery of instructions and student learning outcomes. The purpose of this research is to explore the usage of mobile applications in higher education and develop an application to help college students understand better the class materials, and thereby, enhance their learning outcomes. The detailed description, design, and interface of the application are presented along with dissemination plan.

Protocol for a randomized comparison of integrated versus consecutive dual task practice in Parkinson's disease: the DUALITY trial

NARCIS (Netherlands)

Strouwen, C.; Molenaar, E.A.L.M.; Keus, S.H.J.; Munks, L.; Munneke, M.; Vandenberghe, W.; Bloem, B.R.; Nieuwboer, A.

2014-01-01

BACKGROUND: Multiple tasking is an integral part of daily mobility. Patients with Parkinson's disease have dual tasking difficulties due to their combined motor and cognitive deficits. Two contrasting physiotherapy interventions have been proposed to alleviate dual tasking difficulties: either to

Exploration of dual supply voltage logic synthesis in state-of-the-art ASIC design flows

Directory of Open Access Journals (Sweden)

T. Mahnke

2003-01-01

Full Text Available Dual supply voltage scaling (DSVS for logiclevel power optimization at the has increasingly attracted attention over the last few years. However, mainly due to the fact that the most widely used design tools do not support this new technique, it has still not become an integral part of real-world design flows. In this paper, a novel logic synthesis methodology that enables DSVS while relying entirely on standard tools is presented. The key to this methodology is a suitably modeled dual supply voltage (DSV standard cell library. A basic evaluation of the methodology has been carried out on a number of MCNC benchmark circuits. In all these experiments, the results of state-of-the-art powerdriven single supply voltage (SSV logic synthesis have been used as references in order to determine the true additional benefit of DSVS. Compared with the results of SSV power optimization, additional power reductions of 10% on average have been achieved. The results prove the feasibility of the new approach and reveal its greater efficiency in comparison with a well-known dedicated DSVS algorithm. Finally, the methodology has been applied to an embedded microcontroller core in order to further explore the potentials and limitations of DSVS in an existing industrial design environment.

The design of a linear L-band high power amplifier for mobile communication satellites

Science.gov (United States)

Whittaker, N.; Brassard, G.; Li, E.; Goux, P.

1990-01-01

A linear L-band solid state high power amplifier designed for the space segment of the Mobile Satellite (MSAT) mobile communication system is described. The amplifier is capable of producing 35 watts of RF power with multitone signal at an efficiency of 25 percent and with intermodulation products better than 16 dB below carrier.

Dual Y-Shaped Monopole Antenna for Dual-Band WLAN/WiMAX Operations

Directory of Open Access Journals (Sweden)

Huiqing Zhai

2014-01-01

Full Text Available A dual-band design of monopole antenna with two coupled Y-shaped strips for WLAN/WiMAX applications is presented. By the introduction of dual Y-shaped strips, two separated impedance bandwidths of 22.4% (3.28~4.10 GHz and 19.2% (4.90~5.94 GHz can be obtained to meet the specifications of the WLAN/WiMAX communication band applications. The proposed antenna is successfully simulated, designed, and measured, demonstrating the matched impedance and good radiation characteristics with an overall dimension of 17.7×26×1 mm3.

Educating Urban Designers using Augmented Reality and Mobile Learning Technologies

Directory of Open Access Journals (Sweden)

Ernest Redondo

2017-03-01

Full Text Available This paper describes an educational experience using augmented reality (AR on mobile devices as a  tool for learning urban design concepts and specifically for architecture degree students. In a real project-based exercise, the participants had to design a sculpture to be placed in a public space, checking the suitability of the object as for example the form, scale, location, materials, etc., and taking into account the surroundings. The project is controlled on-site using AR on mobile platforms, encouraging collaborative learning by sharing the 3D models of their proposals, and acting both as producers and consumers of AR content in the process. To assess both the usability of technology, as well as the learning improvement, the class was divided into two groups with equivalent pre-course grades: a control group, who followed the conventional course in the laboratory, and a test group, who used AR technology. At the end of the course, the AR-using group showed a significant increase in academic performance, higher motivation and satisfaction compared to the control group.

A fast spectrum dual path flow cermet reactor

International Nuclear Information System (INIS)

Anghaie, S.; Feller, G.J.; Peery, S.D.; Parsley, R.C.

1993-01-01

A cermet fueled, dual path fast reactor for space nuclear propulsion applications is conceptually designed. The reactor utilizes an outer annulus core and an inner cylindrical core with radial and axial reflector. The dual path flow minimizes the impact of power peaking near the radial reflector. Basic neutronics and core design aspects of the reactor are discussed. The dual path reactor is integrated into a 25000 lbf thrust nuclear rocket

Design and implementation of a dual-wavelength intrinsic fluorescence camera system

Science.gov (United States)

Ortega-Martinez, Antonio; Musacchia, Joseph J.; Gutierrez-Herrera, Enoch; Wang, Ying; Franco, Walfre

2017-03-01

Intrinsic UV fluorescence imaging is a technique that permits the observation of spatial differences in emitted fluorescence. It relies on the fluorescence produced by the innate fluorophores in the sample, and thus can be used for marker-less in-vivo assessment of tissue. It has been studied as a tool for the study of the skin, specifically for the classification of lesions, the delimitation of lesion borders and the study of wound healing, among others. In its most basic setup, a sample is excited with a narrow-band UV light source and the resulting fluorescence is imaged with a UV sensitive camera filtered to the emission wavelength of interest. By carefully selecting the excitation/emission pair, we can observe changes in fluorescence associated with physiological processes. One of the main drawbacks of this simple setup is the inability to observe more than a single excitation/emission pair at the same time, as some phenomena are better studied when two or more different pairs are studied simultaneously. In this work, we describe the design and the hardware and software implementation of a dual wavelength portable UV fluorescence imaging system. Its main components are an UV camera, a dual wavelength UV LED illuminator (295 and 345 nm) and two different emission filters (345 and 390 nm) that can be swapped by a mechanical filter wheel. The system is operated using a laptop computer and custom software that performs basic pre-processing to improve the image. The system was designed to allow us to image fluorescent peaks of tryptophan and collagen cross links in order to study wound healing progression.

Design and implementation of a Sun tracker with a dual-axis single motor for an optical sensor-based photovoltaic system.

Science.gov (United States)

Wang, Jing-Min; Lu, Chia-Liang

2013-03-06

The dual threats of energy depletion and global warming place the development of methods for harnessing renewable energy resources at the center of public interest. Solar energy is one of the most promising renewable energy resources. Sun trackers can substantially improve the electricity production of a photovoltaic (PV) system. This paper proposes a novel design of a dual-axis solar tracking PV system which utilizes the feedback control theory along with a four-quadrant light dependent resistor (LDR) sensor and simple electronic circuits to provide robust system performance. The proposed system uses a unique dual-axis AC motor and a stand-alone PV inverter to accomplish solar tracking. The control implementation is a technical innovation that is a simple and effective design. In addition, a scaled-down laboratory prototype is constructed to verify the feasibility of the scheme. The effectiveness of the Sun tracker is confirmed experimentally. To conclude, the results of this study may serve as valuable references for future solar energy applications.

Design and Implementation of a Sun Tracker with a Dual-Axis Single Motor for an Optical Sensor-Based Photovoltaic System

Directory of Open Access Journals (Sweden)

Chia-Liang Lu

2013-03-01

Full Text Available The dual threats of energy depletion and global warming place the development of methods for harnessing renewable energy resources at the center of public interest. Solar energy is one of the most promising renewable energy resources. Sun trackers can substantially improve the electricity production of a photovoltaic (PV system. This paper proposes a novel design of a dual-axis solar tracking PV system which utilizes the feedback control theory along with a four-quadrant light dependent resistor (LDR sensor and simple electronic circuits to provide robust system performance. The proposed system uses a unique dual-axis AC motor and a stand-alone PV inverter to accomplish solar tracking. The control implementation is a technical innovation that is a simple and effective design. In addition, a scaled-down laboratory prototype is constructed to verify the feasibility of the scheme. The effectiveness of the Sun tracker is confirmed experimentally. To conclude, the results of this study may serve as valuable references for future solar energy applications.

Design and Implementation of a Sun Tracker with a Dual-Axis Single Motor for an Optical Sensor-Based Photovoltaic System

Science.gov (United States)

Wang, Jing-Min; Lu, Chia-Liang

2013-01-01

The dual threats of energy depletion and global warming place the development of methods for harnessing renewable energy resources at the center of public interest. Solar energy is one of the most promising renewable energy resources. Sun trackers can substantially improve the electricity production of a photovoltaic (PV) system. This paper proposes a novel design of a dual-axis solar tracking PV system which utilizes the feedback control theory along with a four-quadrant light dependent resistor (LDR) sensor and simple electronic circuits to provide robust system performance. The proposed system uses a unique dual-axis AC motor and a stand-alone PV inverter to accomplish solar tracking. The control implementation is a technical innovation that is a simple and effective design. In addition, a scaled-down laboratory prototype is constructed to verify the feasibility of the scheme. The effectiveness of the Sun tracker is confirmed experimentally. To conclude, the results of this study may serve as valuable references for future solar energy applications. PMID:23467030

VA Enterprise Design Patterns - 5.1 (Mobility) Mobile

Data.gov (United States)

Department of Veterans Affairs — First of a set of guidance documents that establish the architectural foundation for mobile computing in the VA. This document outlines the enterprise capabilities...

Screen Time: Alumni Magazines Have Their Designs on Mobile Devices

Science.gov (United States)

Walker, Theresa

2011-01-01

Alumni magazines have their designs on mobile devices. The efforts are tied together, no matter the platform, by a desire for the magazine to be where its readers are and a spirit of experimentation that is akin to what is happening with social media. None of the magazine editors went into this process with any numerical expectations for…

Design of Wideband Dual-Polarized Planar Antenna Using Multimode Concept

Directory of Open Access Journals (Sweden)

Deqiang Yang

2016-01-01

Full Text Available A wideband dual-polarized planar antenna is designed and analyzed by using the theory of characteristic modes (TCM. The eigenvalue, eigencurrent, characteristic pattern, and modal weighting coefficient are analyzed to bring physical insight to this kind of antenna. The results demonstrate that there are two modes resonant in the operating band for each polarization, which have been combined to form a wider frequency band. A bandwidth of 60.2% (1.72–3.2 GHz for VSWR < 1.5 with high isolation of 32 dB is achieved simultaneously. The size of the radiator structure is 0.33λ0 × 0.33λ0 × 0.22λ0 (λ0 refers to the center operating frequency.

Dual stator winding variable speed asynchronous generator: optimal design and experiments

International Nuclear Information System (INIS)

Tutelea, L N; Deaconu, S I; Popa, G N

2015-01-01

In the present paper is carried out a theoretical and experimental study of dual stator winding squirrel cage asynchronous generator (DSWA) behavior in the presence of saturation regime (non-sinusoidal) due to the variable speed operation. The main aims are the determination of the relations of calculating the equivalent parameters of the machine windings to optimal design using a Matlab code. Issue is limited to three phase range of double stator winding cage-induction generator of small sized powers, the most currently used in the small adjustable speed wind or hydro power plants. The tests were carried out using three-phase asynchronous generator having rated power of 6 [kVA]. (paper)

MIMIC: An Innovative Methodology for Determining Mobile Laser Scanning System Point Density

Directory of Open Access Journals (Sweden)

Conor Cahalane

2014-08-01

Full Text Available Understanding how various Mobile Mapping System (MMS laser hardware configurations and operating parameters exercise different influence on point density is important for assessing system performance, which in turn facilitates system design and MMS benchmarking. Point density also influences data processing, as objects that can be recognised using automated algorithms generally require a minimum point density. Although obtaining the necessary point density impacts on hardware costs, survey time and data storage requirements, a method for accurately and rapidly assessing MMS performance is lacking for generic MMSs. We have developed a method for quantifying point clouds collected by an MMS with respect to known objects at specified distances using 3D surface normals, 2D geometric formulae and line drawing algorithms. These algorithms were combined in a system called the Mobile Mapping Point Density Calculator (MIMIC and were validated using point clouds captured by both a single scanner and a dual scanner MMS. Results from MIMIC were promising: when considering the number of scan profiles striking the target, the average error equated to less than 1 point per scan profile. These tests highlight that MIMIC is capable of accurately calculating point density for both single and dual scanner MMSs.

77 FR 14012 - Eligible Telecommunications Carrier Designation for Participation in Mobility Fund Phase I

Science.gov (United States)

2012-03-08

...; DA 12-271] Eligible Telecommunications Carrier Designation for Participation in Mobility Fund Phase I... Wireless Telecommunications and Wireline Competition Bureaus describe the process and requirements for applicants seeking Eligible Telecommunications Carrier (ETC) Designation from the Commission for...

The-Abstraction-Hierarchy-based Mobile PC Display Design for NPP Maintenance

International Nuclear Information System (INIS)

Kim, In; Kim, Bo Gyung; Seong, Poong Hyun; Ha, Jun Su

2010-01-01

Recently, the importance of effective maintenance in nuclear power plants (NPPs) has been emphasized and research into effective maintenance by adopting mobile maintenance aids (MMAs) have been attempted. For improved and effective use of an MMA display design method based on abstraction hierarchy (AH) is proposed and its design considerations are discussed in this study. Six levels of abstraction hierarchy are proposed in this paper to classify the maintenance information. By classifying and organizing maintenance information using AH, maintenance information can be used effectively by users with either high or low levels of expertise. When information classification has been finished, the information for MMA design is selected and designed. With the considerations of MMA design analysis and guidelines, AH-based MMA is designed for the maintenance tasks. An experiment is conducted using the AH-based MMA in order to estimate the effectiveness of the proposed method for the maintenance tasks and to identify design considerations to enhance the proposed MMAs. The result indicated that an AH-based manual was more effective than a conventional manual in terms of task completion time and number of errors. The workload for the AH-based manual was estimated less than the conventional manual for subjects with low level of expertise. As the level of expertise increases, subjects tended to follow more abstract information while the number of navigations decreased. It is believed that when mobile devices become pervasive in NPP maintenance fields, AH-model applied MMAs can be used as an effective maintenance supporting tool

Mechanism design for mobile geo-location advertising

OpenAIRE

Gatti, Nicola; Rocco, Marco; Ceppi, Sofia; Gerding, Enrico H.

2014-01-01

Mobile geo–location advertising, where mobile ads are targeted based on a user’s location, has been identified as a key growth factor for the mobile market. As with online advertising, a crucial ingredient for their success is the development of effective economic mechanisms. An important difference is that mobile ads are shown sequentially over time and information about the user can be learned based on their movements. Furthermore, ads need to be shown selectively to prevent ad fatigue. To ...

Design and Implementation of Mobile Blended Learning Model Based on WeChat Public Platform

Directory of Open Access Journals (Sweden)

Han Yanyan

2017-01-01

Full Text Available Merging together the ideas of mobile learning, blended learning and flipped classroom, a Mobile Blended Learning Model (MBLM is constructed. Based on WeChat Public Platform (WPP, MBLM can optimize the instructional process and improve the learning efficiency. A Mobile Blended Learning System(MBLS is implemented by using MBLM, and it is constructed by both WPP and auxiliary learning system which based on Java Web. This system has reasonable designed function, easy operation, and beautiful interface, so it can effectively promote the popularization of MBLM.

Modeling the energy performance of event-driven wireless sensor network by using static sink and mobile sink.

Science.gov (United States)

Chen, Jiehui; Salim, Mariam B; Matsumoto, Mitsuji

2010-01-01

Wireless Sensor Networks (WSNs) designed for mission-critical applications suffer from limited sensing capacities, particularly fast energy depletion. Regarding this, mobile sinks can be used to balance the energy consumption in WSNs, but the frequent location updates of the mobile sinks can lead to data collisions and rapid energy consumption for some specific sensors. This paper explores an optimal barrier coverage based sensor deployment for event driven WSNs where a dual-sink model was designed to evaluate the energy performance of not only static sensors, but Static Sink (SS) and Mobile Sinks (MSs) simultaneously, based on parameters such as sensor transmission range r and the velocity of the mobile sink v, etc. Moreover, a MS mobility model was developed to enable SS and MSs to effectively collaborate, while achieving spatiotemporal energy performance efficiency by using the knowledge of the cumulative density function (cdf), Poisson process and M/G/1 queue. The simulation results verified that the improved energy performance of the whole network was demonstrated clearly and our eDSA algorithm is more efficient than the static-sink model, reducing energy consumption approximately in half. Moreover, we demonstrate that our results are robust to realistic sensing models and also validate the correctness of our results through extensive simulations.

Modeling the Energy Performance of Event-Driven Wireless Sensor Network by Using Static Sink and Mobile Sink

Science.gov (United States)

Chen, Jiehui; Salim, Mariam B.; Matsumoto, Mitsuji

2010-01-01

Wireless Sensor Networks (WSNs) designed for mission-critical applications suffer from limited sensing capacities, particularly fast energy depletion. Regarding this, mobile sinks can be used to balance the energy consumption in WSNs, but the frequent location updates of the mobile sinks can lead to data collisions and rapid energy consumption for some specific sensors. This paper explores an optimal barrier coverage based sensor deployment for event driven WSNs where a dual-sink model was designed to evaluate the energy performance of not only static sensors, but Static Sink (SS) and Mobile Sinks (MSs) simultaneously, based on parameters such as sensor transmission range r and the velocity of the mobile sink v, etc. Moreover, a MS mobility model was developed to enable SS and MSs to effectively collaborate, while achieving spatiotemporal energy performance efficiency by using the knowledge of the cumulative density function (cdf), Poisson process and M/G/1 queue. The simulation results verified that the improved energy performance of the whole network was demonstrated clearly and our eDSA algorithm is more efficient than the static-sink model, reducing energy consumption approximately in half. Moreover, we demonstrate that our results are robust to realistic sensing models and also validate the correctness of our results through extensive simulations. PMID:22163503

Real-time mobile customer short message system design and implementation

Science.gov (United States)

Han, Qirui; Sun, Fang

To expand the current mobile phone short message service, and to make the contact between schools, teachers, parents and feedback of the modern school office system more timely and conveniently, designed and developed the Short Message System based on the Linux platform. The state-of-the-art principles and designed proposals in the Short Message System based on the Linux platform are introduced. Finally we propose an optimized secure access authentication method. At present, many schools,vbusinesses and research institutions ratify the promotion and application the messaging system gradually, which has shown benign market prospects.

Optimizing digital elevation models (DEMs) accuracy for planning and design of mobile communication networks

Science.gov (United States)

Hassan, Mahmoud A.

2004-02-01

Digital elevation models (DEMs) are important tools in the planning, design and maintenance of mobile communication networks. This research paper proposes a method for generating high accuracy DEMs based on SPOT satellite 1A stereo pair images, ground control points (GCP) and Erdas OrthoBASE Pro image processing software. DEMs with 0.2911 m mean error were achieved for the hilly and heavily populated city of Amman. The generated DEM was used to design a mobile communication network resulted in a minimum number of radio base transceiver stations, maximum number of covered regions and less than 2% of dead zones.

Leveraging design thinking to build sustainable mobile health systems.

Science.gov (United States)

Eckman, Molly; Gorski, Irena; Mehta, Khanjan

Mobile health, or mHealth, technology has the potential to improve health care access in the developing world. However, the majority of mHealth projects do not expand beyond the pilot stage. A core reason why is because they do not account for the individual needs and wants of those involved. A collaborative approach is needed to integrate the perspectives of all stakeholders into the design and operation of mHealth endeavours. Design thinking is a methodology used to develop and evaluate novel concepts for systems. With roots in participatory processes and self-determined pathways, design thinking provides a compelling framework to understand and apply the needs of diverse stakeholders to mHealth project development through a highly iterative process. The methodology presented in this article provides a structured approach to apply design thinking principles to assess the feasibility of novel mHealth endeavours during early conceptualisation.

Designing personal attentive user interfaces in the mobile public safety domain

NARCIS (Netherlands)

Streefkerk, J.W.; Esch van-Bussemakers, M.P.; Neerincx, M.A.

2006-01-01

In the mobile computing environment, there is a need to adapt the information and service provision to the momentary attentive state of the user, operational requirements and usage context. This paper proposes to design personal attentive user interfaces (PAUI) for which the content and style of

Design of Mobile Learning strategies through blended learning enviroment

Directory of Open Access Journals (Sweden)

Oscar Boude Figueredo

2017-06-01

Full Text Available This paper presents the results of an investigation that developed in the municipality of Fusagasuga in late 2013 by the University of La Sabana are presented, whose objective was to determine the contribution of a process of teacher training in the design of strategies for mobile learning. A methodological level a qualitative study, with exploratory scope, was conducted through a case study. In it, 245 teachers participated in 13 educational institu-tions. The main results show that teachers recognize the importance of using mobile devices to support the development of their teaching practices, and promote the participation of their students as well as some aspects that hinder and facilitate the development of this type of training processes. The main conclusion is that although the use of devices is increasingly in classrooms, this use does not respond to a didactic planning by the teacher.

DUAL TIMELIKE NORMAL AND DUAL TIMELIKE SPHERICAL CURVES IN DUAL MINKOWSKI SPACE

OpenAIRE

ÖNDER, Mehmet

2009-01-01

Abstract: In this paper, we give characterizations of dual timelike normal and dual timelike spherical curves in the dual Minkowski 3-space and we show that every dual timelike normal curve is also a dual timelike spherical curve. Keywords: Normal curves, Dual Minkowski 3-Space, Dual Timelike curves. Mathematics Subject Classifications (2000): 53C50, 53C40. DUAL MINKOWSKI UZAYINDA DUAL TIMELIKE NORMAL VE DUAL TIMELIKE KÜRESEL EĞRİLER Özet: Bu çalışmada, dual Minkowski 3-...

Design and analysis of a dual mode CMOS field programmable analog array

International Nuclear Information System (INIS)

Cheng Xiaoyan; Yang Haigang; Yin Tao; Wu Qisong; Zhang Hongfeng; Liu Fei

2014-01-01

This paper presents a novel field-programmable analog array (FPAA) architecture featuring a dual mode including discrete-time (DT) and continuous-time (CT) operation modes, along with a highly routable connection boxes (CBs) based interconnection lattice. The dual mode circuit for the FPAA is capable of achieving targeted optimal performance in different applications. The architecture utilizes routing switches in a CB not only for the signal interconnection purpose but also for control of the electrical charge transfer required in switched-capacitor circuits. This way, the performance of the circuit in either mode shall not be hampered with adding of programmability. The proposed FPAA is designed and implemented in a 0.18 μm standard CMOS process with a 3.3 V supply voltage. The result from post-layout simulation shows that a maximum bandwidth of 265 MHz through the interconnection network is achieved. The measured results from demonstrated examples show that the maximum signal bandwidth of up to 2 MHz in CT mode is obtained with the spurious free dynamic range of 54 dB, while the signal processing precision in DT mode reaches 96.4%. (semiconductor integrated circuits)

The Design and Testing of a Dual Fiber Textile Matrix for Accelerating Surface Hemostasis

Science.gov (United States)

Fischer, Thomas H.; Vournakis, John N.; Manning, James E.; McCurdy, Shane L.; Rich, Preston B.; Nichols, Timothy C.; Scull, Christopher M.; McCord, Marian G.; Decorta, Joseph A.; Johnson, Peter C.; Smith, Carr J.

2011-01-01

The standard treatment for severe traumatic injury is frequently compression and application of gauze dressing to the site of hemorrhage. However, while able to rapidly absorb pools of shed blood, gauze fails to provide strong surface (topical) hemostasis. The result can be excess hemorrhage-related morbidity and mortality. We hypothesized that cost-effective materials (based on widespread availability of bulk fibers for other commercial uses) could be designed based on fundamental hemostatic principles to partially emulate the wicking properties of gauze while concurrently stimulating superior hemostasis. A panel of readily available textile fibers was screened for the ability to activate platelets and the intrinsic coagulation cascade in vitro. Type E continuous filament glass and a specialty rayon fiber were identified from the material panel as accelerators of hemostatic reactions and were custom woven to produce a dual fiber textile bandage. The glass component strongly activated platelets while the specialty rayon agglutinated red blood cells. In comparison with gauze in vitro, the dual fiber textile significantly enhanced the rate of thrombin generation, clot generation as measured by thromboelastography, adhesive protein adsorption and cellular attachment and activation. These results indicate that hemostatic textiles can be designed that mimic gauze in form but surpass gauze in ability to accelerate hemostatic reactions. PMID:19489008

Design of an anti-Rician-fading modem for mobile satellite communication systems

Science.gov (United States)

Kojima, Toshiharu; Ishizu, Fumio; Miyake, Makoto; Murakami, Keishi; Fujino, Tadashi

1995-01-01

To design a demodulator applicable to mobile satellite communication systems using differential phase shift keying modulation, we have developed key technologies including an anti-Rician-fading demodulation scheme, an initial acquisition scheme, automatic gain control (AGC), automatic frequency control (AFC), and bit timing recovery (BTR). Using these technologies, we have developed one-chip digital signal processor (DSP) modem for mobile terminal, which is compact, of light weight, and of low power consumption. Results of performance test show that the developed DSP modem achieves good performance in terms of bit error ratio in mobile satellite communication environment, i.e., Rician fading channel. It is also shown that the initial acquisition scheme acquires received signal rapidly even if the carrier-to-noise power ratio (CNR) of the received signal is considerably low.

Antenna Design Considerations for the Advanced Extravehicular Mobility Unit

Science.gov (United States)

Bakula, Casey J.; Theofylaktos, Onoufrios

2015-01-01

NASA is designing an Advanced Extravehicular Mobility Unit (AEMU)to support future manned missions beyond low-Earth orbit (LEO). A key component of the AEMU is the communications assembly that allows for the wireless transfer of voice, video, and suit telemetry. The Extravehicular Mobility Unit (EMU) currently used on the International Space Station (ISS) contains a radio system with a single omni-directional resonant cavity antenna operating slightly above 400 MHz capable of transmitting and receiving data at a rate of about 125 kbps. Recent wireless communications architectures are calling for the inclusion of commercial wireless standards such as 802.11 that operate in higher frequency bands at much higher data rates. The current AEMU radio design supports a 400 MHz band for low-rate mission-critical data and a high-rate band based on commercial wireless local area network (WLAN) technology to support video, communication with non-extravehicular activity (EVA) assets such as wireless sensors and robotic assistants, and a redundant path for mission-critical EVA data. This paper recommends the replacement of the existing EMU antenna with a new antenna that maintains the performance characteristics of the current antenna but with lower weight and volume footprints. NASA has funded several firms to develop such an antenna over the past few years, and the most promising designs are variations on the basic patch antenna. This antenna technology at UHF is considered by the authors to be mature and ready for infusion into NASA AEMU technology development programs.

Neutronic design analyses for a dual-coolant blanket concept: Optimization for a fusion reactor DEMO

International Nuclear Information System (INIS)

Palermo, I.; Gómez-Ros, J.M.; Veredas, G.; Sanz, J.; Sedano, L.

2012-01-01

Highlights: ► Dual-Coolant He/Pb15.7Li breeding blanket for a DEMO fusion reactor is studied. ► An iterative process optimizes neutronic responses minimizing reactor dimension. ► A 3D toroidally symmetric geometry has been generated from the CAD model. ► Overall TBR values support the feasibility of the conceptual model considered. ► Power density in TF coils is below load limit for quenching. - Abstract: The generation of design specifications for a DEMO reactor, including breeding blanket (BB), vacuum vessel (VV) and magnetic field coils (MFC), requires a consistent neutronic optimization of structures between plasma and MFC. This work targets iteratively to generate these neutronic specifications for a Dual-Coolant He/Pb15.7Li breeding blanket design. The iteration process focuses on the optimization of allowable space between plasma scrapped-off-layer and VV in order to generate a MFC/VV/BB/plasma sustainable configuration with minimum global system volumes. Two VV designs have been considered: (1) a double-walled option with light-weight stiffeners and (2) a thick massive one. The optimization process also involves VV materials, looking to warrant radiation impact operational limits on the MFC. The resulting nuclear responses: peak nuclear heating in toroidal field (TF) coil, tritium breeding ratio (TBR), power amplification factor and helium production in the structural material are provided.

Mobile Technology and CAD Technology Integration in Teaching Architectural Design Process for Producing Creative Product

Science.gov (United States)

Bin Hassan, Isham Shah; Ismail, Mohd Arif; Mustafa, Ramlee

2011-01-01

The purpose of this research is to examine the effect of integrating the mobile and CAD technology on teaching architectural design process for Malaysian polytechnic architectural students in producing a creative product. The website is set up based on Caroll's minimal theory, while mobile and CAD technology integration is based on Brown and…

Design on a Composite Mobile System for Exploration Robot

OpenAIRE

Shang, Weiyan; Yang, Canjun; Liu, Yunping; Wang, Junming

2016-01-01

In order to accomplish exploration missions in complex environments, a new type of robot has been designed. By analyzing the characteristics of typical moving systems, a new mobile system which is named wheel-tracked moving system (WTMS) has been presented. Then by virtual prototype simulation, the new system’s ability to adapt complex environments has been verified. As the curve of centroid acceleration changes in large amplitude in this simulation, ride performance of this robot has been st...

Design and synthesis of dual inhibitors of acetylcholinesterase and serotonin transporter targeting potential agents for Alzheimer's disease.

Science.gov (United States)

Kogen, Hiroshi; Toda, Narihiro; Tago, Keiko; Marumoto, Shinji; Takami, Kazuko; Ori, Mayuko; Yamada, Naho; Koyama, Kazuo; Naruto, Shunji; Abe, Kazumi; Yamazaki, Reina; Hara, Takao; Aoyagi, Atsushi; Abe, Yasuyuki; Kaneko, Tsugio

2002-10-03

Highly efficient acetylcholinesterase (AChE) and serotonin transporter (SERT) dual inhibitors, (S)-4 and (R)-13 were designed and synthesized on the basis of the hypothetical model of AChE active site. Both compounds showed potent inhibitory activities against AChE and SERT. [structure: see text

Design of a Mobile Robot for Air Ducts Exploration

Directory of Open Access Journals (Sweden)

Moses A. Koledoye

2017-10-01

Full Text Available This work presents the solutions adopted for the design and the implementation of an autonomous wheeled robot developed for the exploration and mapping of air ventilation ducts. The hardware is based on commercial off-the-shelf devices, including sensors, motors, processing devices and interfaces. The mechanical chassis was designed from scratch to meet a trade-off between small size and available volume to host the components. The software stack is based on the Robot Operating System (ROS. Special attention was dedicated to the design of the mobility strategy, which must take into account some constraints and issues that are specific to the considered application, such as the relatively small size of ducts, the need to detect and avoid possible holes on the floor of the duct and other unusual obstacles and the unavailability of external reference frameworks for localization. The main contribution of this paper lies in the design, implementation and experimentation of the overall system.

GPU-based Parallel Application Design for Emerging Mobile Devices

Science.gov (United States)

Gupta, Kshitij

A revolution is underway in the computing world that is causing a fundamental paradigm shift in device capabilities and form-factor, with a move from well-established legacy desktop/laptop computers to mobile devices in varying sizes and shapes. Amongst all the tasks these devices must support, graphics has emerged as the 'killer app' for providing a fluid user interface and high-fidelity game rendering, effectively making the graphics processor (GPU) one of the key components in (present and future) mobile systems. By utilizing the GPU as a general-purpose parallel processor, this dissertation explores the GPU computing design space from an applications standpoint, in the mobile context, by focusing on key challenges presented by these devices---limited compute, memory bandwidth, and stringent power consumption requirements---while improving the overall application efficiency of the increasingly important speech recognition workload for mobile user interaction. We broadly partition trends in GPU computing into four major categories. We analyze hardware and programming model limitations in current-generation GPUs and detail an alternate programming style called Persistent Threads, identify four use case patterns, and propose minimal modifications that would be required for extending native support. We show how by manually extracting data locality and altering the speech recognition pipeline, we are able to achieve significant savings in memory bandwidth while simultaneously reducing the compute burden on GPU-like parallel processors. As we foresee GPU computing to evolve from its current 'co-processor' model into an independent 'applications processor' that is capable of executing complex work independently, we create an alternate application framework that enables the GPU to handle all control-flow dependencies autonomously at run-time while minimizing host involvement to just issuing commands, that facilitates an efficient application implementation. Finally, as

Secure, Mobile, Wireless Network Technology Designed, Developed, and Demonstrated

Science.gov (United States)

Ivancic, William D.; Paulsen, Phillip E.

2004-01-01

The inability to seamlessly disseminate data securely over a high-integrity, wireless broadband network has been identified as a primary technical barrier to providing an order-of-magnitude increase in aviation capacity and safety. Secure, autonomous communications to and from aircraft will enable advanced, automated, data-intensive air traffic management concepts, increase National Air Space (NAS) capacity, and potentially reduce the overall cost of air travel operations. For the first time ever, secure, mobile, network technology was designed, developed, and demonstrated with state-ofthe- art protocols and applications by a diverse, cooperative Government-industry team led by the NASA Glenn Research Center. This revolutionary technology solution will make fundamentally new airplane system capabilities possible by enabling secure, seamless network connections from platforms in motion (e.g., cars, ships, aircraft, and satellites) to existing terrestrial systems without the need for manual reconfiguration. Called Mobile Router, the new technology autonomously connects and configures networks as they traverse from one operating theater to another. The Mobile Router demonstration aboard the Neah Bay, a U.S. Coast Guard vessel stationed in Cleveland, Ohio, accomplished secure, seamless interoperability of mobile network systems across multiple domains without manual system reconfiguration. The Neah Bay was chosen because of its low cost and communications mission similarity to low-Earth-orbiting satellite platforms. This technology was successfully advanced from technology readiness level (TRL) 2 (concept and/or application formation) to TRL 6 (system model or prototype demonstration in a relevant environment). The secure, seamless interoperability offered by the Mobile Router and encryption device will enable several new, vehicle-specific and systemwide technologies to perform such things as remote, autonomous aircraft performance monitoring and early detection and

Dual fan, dual-duct system meets air quality, energy-efficiency needs

Energy Technology Data Exchange (ETDEWEB)

Schuler, M. [Pageau Morel and Associates, Montreal, Quebec (Canada)

1996-03-01

Canada`s Space Centre in Saint-Hubert Quebec is a 300,000 ft{sup 2} (27,871 m{sup 2}) complex that houses the headquarters of the Canadian Space Agency, the Canadian Astronaut Training Centre, mission ground control installations, research facilities, offices and the required support facilities. A comfortable, pleasant research environment was a primary concern for the Space Centre, given its elite clientele. The objectives were high indoor-air quality, design flexibility, energy efficiency and low capital costs. Dual duct systems which are the heart of the mechanical concept allowed the designers to meet these objectives. The Space Centre`s offices, laboratories and conference center are all served by dual-duct systems. All operate using an air economizer cycle. Gas boilers provide them with hot water for heating and steam for humidification while centrifugal chillers provide chilled water for cooling. This article describes the design.

The impact of the mode of survey administration on estimates of daily smoking for mobile phone only users

Directory of Open Access Journals (Sweden)

Joseph Hanna

2017-04-01

Full Text Available Abstract Background Over the past decade, there have been substantial changes in landline and mobile phone ownership, with a substantial increase in the proportion of mobile-only households. Estimates of daily smoking rates for the mobile phone only (MPO population have been found to be substantially higher than the rest of the population and telephone surveys that use a dual sampling frame (landline and mobile phones are now considered best practice. Smoking is seen as an undesirable behaviour; measuring such behaviours using an interviewer may lead to lower estimates when using telephone based surveys compared to self-administered approaches. This study aims to assess whether higher daily smoking estimates observed for the mobile phone only population can be explained by administrative features of surveys, after accounting for differences in the phone ownership population groups. Methods Data on New South Wales (NSW residents aged 18 years or older from the NSW Population Health Survey (PHS, a telephone survey, and the National Drug Strategy Household Survey (NDSHS, a self-administered survey, were combined, with weights adjusted to match the 2013 population. Design-adjusted prevalence estimates and odds ratios were calculated using survey analysis procedures available in SAS 9.4. Results Both the PHS and NDSHS gave the same estimates for daily smoking (12% and similar estimates for MPO users (20% and 18% respectively. Pooled data showed that daily smoking was 19% for MPO users, compared to 10% for dual phone owners, and 12% for landline phone only users. Prevalence estimates for MPO users across both surveys were consistently higher than other phone ownership groups. Differences in estimates for the MPO population compared to other phone ownership groups persisted even after adjustment for the mode of collection and demographic factors. Conclusions Daily smoking rates were consistently higher for the mobile phone only population and this was

There's not an app for that mobile user experience design for life

CERN Document Server

Robinson, Simon; Jones, Matt

2014-01-01

There's Not an App for That will make your work stand out from the crowd. It walks you through mobile experiences, and teaches you to evaluate current UX approaches, enabling you to think outside of the screen and beyond the conventional. You'll review diverse aspects of mobile UX: the screens, the experience, how apps are used, and why they're used. You'll find special sections on ""challenging your approach"", as well as a series of questions you can use to critique and evaluate your own designs. Whether the authors are discussing real-world products in conjunction with suggested improvemen

Research on dynamic performance design of mobile phone application based on context awareness

Science.gov (United States)

Bo, Zhang

2018-05-01

It aims to explore the dynamic performance of different mobile phone applications and the user's cognitive differences, reduce the cognitive burden, and enhance the sense of experience. By analyzing the dynamic design performance in four different interactive contexts, and constructing the framework of information service process in the interactive context perception and the two perception principles of the cognitive consensus between designer and user, and the two kinds of knowledge in accordance with the perception principles. The analysis of the context will help users sense the dynamic performance more intuitively, so that the details of interaction will be performed more vividly and smoothly, thus enhance user's experience in the interactive process. The common perception experience enables designers and users to produce emotional resonance in different interactive contexts, and help them achieve rapid understanding of interactive content and perceive the logic and hierarchy of the content and the structure, therefore the effectiveness of mobile applications will be improved.

Designing iCanFit: A Mobile-Enabled Web Application to Promote Physical Activity for Older Cancer Survivors.

Science.gov (United States)

Hong, Yan; Dahlke, Deborah Vollmer; Ory, Marcia; Hochhalter, Angela; Reynolds, Jana; Purcell, Ninfa Pena; Talwar, Divya; Eugene, Nola

2013-02-14

Most older cancer survivors (OCS) do not engage in regular physical activity (PA) despite well-known health benefits. With the increased use of mobile technologies among older adults, mobile tools may be an effective method to deliver PA promotion programs for OCS. To document the process of designing an OCS-friendly mobile-enabled Web application of PA promotion program. Mixed methods encompassing group discussions, individual interviews, and brief surveys with community leaders, OCS, cancer care providers, and software professionals were used in this formative research. The varied stakeholders welcomed the idea of developing an online tool to promote PA in OCS. Our formative research revealed several major barriers to regular PA including limited access to senior-friendly PA resources, lack of motivation and social support, and insufficient knowledge and skills on building safe and appropriate workout plans. This feedback was incorporated into the development of iCanFit, a mobile-enabled Web application, designed specifically for OCS. The iCanFit online tools allow users to locate PA resources, set and track goals for PA, network with peer OCS in a secure online space, and receive practical and evidence-informed healthy tips. Our mixed-method formative research led to the design of iCanFit protocol to promote PA and well-being of OCS. The involvement of stakeholders is critical in the planning and design of the mobile application in order to enhance program relevance, appeal, and match with the needs of target users.

Dual EC : a standardized back door

NARCIS (Netherlands)

Bernstein, D.J.; Lange, T.; Niederhagen, R.F.

2015-01-01

Dual EC is an algorithm to compute pseudorandom numbers starting from some random input. Dual EC was standardized by NIST, ANSI, and ISO among other algorithms to generate pseudorandom numbers. For a long time this algorithm was considered suspicious -- the entity designing the algorithm could have

Design and Development of a Mobile Sensor Based the Blind Assistance Wayfinding System

Science.gov (United States)

Barati, F.; Delavar, M. R.

2015-12-01

The blind and visually impaired people are facing a number of challenges in their daily life. One of the major challenges is finding their way both indoor and outdoor. For this reason, routing and navigation independently, especially in urban areas are important for the blind. Most of the blind undertake route finding and navigation with the help of a guide. In addition, other tools such as a cane, guide dog or electronic aids are used by the blind. However, in some cases these aids are not efficient enough in a wayfinding around obstacles and dangerous areas for the blind. As a result, the need to develop effective methods as decision support using a non-visual media is leading to improve quality of life for the blind through their increased mobility and independence. In this study, we designed and implemented an outdoor mobile sensor-based wayfinding system for the blind. The objectives of this study are to guide the blind for the obstacle recognition and the design and implementation of a wayfinding and navigation mobile sensor system for them. In this study an ultrasonic sensor is used to detect obstacles and GPS is employed for positioning and navigation in the wayfinding. This type of ultrasonic sensor measures the interval between sending waves and receiving the echo signals with respect to the speed of sound in the environment to estimate the distance to the obstacles. In this study the coordinates and characteristics of all the obstacles in the study area are already stored in a GIS database. All of these obstacles were labeled on the map. The ultrasonic sensor designed and constructed in this study has the ability to detect the obstacles in a distance of 2cm to 400cm. The implementation and the results obtained from the interview of a number of blind persons who employed the sensor verified that the designed mobile sensor system for wayfinding was very satisfactory.

DESIGN AND DEVELOPMENT OF A MOBILE SENSOR BASED THE BLIND ASSISTANCE WAYFINDING SYSTEM

Directory of Open Access Journals (Sweden)

F. Barati

2015-12-01

Full Text Available The blind and visually impaired people are facing a number of challenges in their daily life. One of the major challenges is finding their way both indoor and outdoor. For this reason, routing and navigation independently, especially in urban areas are important for the blind. Most of the blind undertake route finding and navigation with the help of a guide. In addition, other tools such as a cane, guide dog or electronic aids are used by the blind. However, in some cases these aids are not efficient enough in a wayfinding around obstacles and dangerous areas for the blind. As a result, the need to develop effective methods as decision support using a non-visual media is leading to improve quality of life for the blind through their increased mobility and independence. In this study, we designed and implemented an outdoor mobile sensor-based wayfinding system for the blind. The objectives of this study are to guide the blind for the obstacle recognition and the design and implementation of a wayfinding and navigation mobile sensor system for them. In this study an ultrasonic sensor is used to detect obstacles and GPS is employed for positioning and navigation in the wayfinding. This type of ultrasonic sensor measures the interval between sending waves and receiving the echo signals with respect to the speed of sound in the environment to estimate the distance to the obstacles. In this study the coordinates and characteristics of all the obstacles in the study area are already stored in a GIS database. All of these obstacles were labeled on the map. The ultrasonic sensor designed and constructed in this study has the ability to detect the obstacles in a distance of 2cm to 400cm. The implementation and the results obtained from the interview of a number of blind persons who employed the sensor verified that the designed mobile sensor system for wayfinding was very satisfactory.

Second-generation mobile satellite system. A conceptual design and trade-off study

Science.gov (United States)

Sue, M. K.; Park, Y. H.

1985-01-01

In recent years, interest has grown in the mobile satellite (MSAT) system, a satellite-based communications system capable of providing integrated voice and data services to a large number of users. To explore the potential of a commercial mobile satellite system (MSS) beyond the horizon of the first generation, using technologies of the 1990's and to assist MSAT-X in directing its efforts, a conceptual design has been performed for a second-generation system to be launched around the mid-1990's. The design goal is to maximize the number of satellite channels and/or minimize the overall life-cycle cost, subject to the constraint of utilizing a commercial satellite bus with minimum modifications. To provide an optimal design, a series of trade-offs are performed, including antenna sizing, feed configurations, and interference analysis. Interference is a serious problem for MSAT and often an overlapping feed design is required to reduce interbeam interference. The trade-off studies will show that a simple non-overlapping feed is sufficient for the second-generation system, thus avoiding the need for the complicated beam-forming network that is associated with the overlapping feed designs. In addition, a system that operates at L-band, an alternative frequency band that is being considered by some for possible MSAT applications, is also presented.

Energy Efficient Hybrid Dual Axis Solar Tracking System

Directory of Open Access Journals (Sweden)

Rashid Ahammed Ferdaus

2014-01-01

Full Text Available This paper describes the design and implementation of an energy efficient solar tracking system from a normal mechanical single axis to a hybrid dual axis. For optimizing the solar tracking mechanism electromechanical systems were evolved through implementation of different evolutional algorithms and methodologies. To present the tracker, a hybrid dual-axis solar tracking system is designed, built, and tested based on both the solar map and light sensor based continuous tracking mechanism. These light sensors also compare the darkness and cloudy and sunny conditions assisting daily tracking. The designed tracker can track sun’s apparent position at different months and seasons; thereby the electrical controlling device requires a real time clock device for guiding the tracking system in seeking solar position for the seasonal motion. So the combination of both of these tracking mechanisms made the designed tracker a hybrid one. The power gain and system power consumption are compared with a static and continuous dual axis solar tracking system. It is found that power gain of hybrid dual axis solar tracking system is almost equal to continuous dual axis solar tracking system, whereas the power saved in system operation by the hybrid tracker is 44.44% compared to the continuous tracking system.

Dual leadership in a hospital practice

DEFF Research Database (Denmark)

Thude, Bettina Ravnborg; Thomsen, Svend Erik; Stenager, Egon

2017-01-01

, this study aims to analyse three different dual leadership pairs at a Danish hospital. Furthermore, this study develops a tool to characterize dual leadership teams from each other. Design/methodology/approach This is a qualitative study using semi-structured interviews. Six leaders were interviewed...... to clarify how dual leadership works in a hospital context. All interviews were transcribed and coded. During coding, focus was on the nine principles found in the literature and another principle was found by looking at the themes that were generic for all six interviews. Findings Results indicate......Purpose Despite the practice of dual leadership in many organizations, there is relatively little research on the topic. Dual leadership means two leaders share the leadership task and are held jointly accountable for the results of the unit. To better understand how dual leadership works...

Mobile Voting Tools for Creating Collaboration Environment and a New Educational Design of the University Lecture

Science.gov (United States)

Titova, Svetlana

2014-01-01

Mobile devices can enhance learning experience in many ways: provide instant feedback and better diagnosis of learning problems; enhance learner autonomy; create mobile networking collaboration; help design enquiry-based activities based on augmented reality, geo-location awareness and video-capture. One of the main objectives of the international…

Adaptive intervention design in mobile health: Intervention design and development in the Cell Phone Intervention for You trial.

Science.gov (United States)

Lin, Pao-Hwa; Intille, Stephen; Bennett, Gary; Bosworth, Hayden B; Corsino, Leonor; Voils, Corrine; Grambow, Steven; Lazenka, Tony; Batch, Bryan C; Tyson, Crystal; Svetkey, Laura P

2015-12-01

The obesity epidemic has spread to young adults, and obesity is a significant risk factor for cardiovascular disease. The prominence and increasing functionality of mobile phones may provide an opportunity to deliver longitudinal and scalable weight management interventions in young adults. The aim of this article is to describe the design and development of the intervention tested in the Cell Phone Intervention for You study and to highlight the importance of adaptive intervention design that made it possible. The Cell Phone Intervention for You study was a National Heart, Lung, and Blood Institute-sponsored, controlled, 24-month randomized clinical trial comparing two active interventions to a usual-care control group. Participants were 365 overweight or obese (body mass index≥25 kg/m2) young adults. Both active interventions were designed based on social cognitive theory and incorporated techniques for behavioral self-management and motivational enhancement. Initial intervention development occurred during a 1-year formative phase utilizing focus groups and iterative, participatory design. During the intervention testing, adaptive intervention design, where an intervention is updated or extended throughout a trial while assuring the delivery of exactly the same intervention to each cohort, was employed. The adaptive intervention design strategy distributed technical work and allowed introduction of novel components in phases intended to help promote and sustain participant engagement. Adaptive intervention design was made possible by exploiting the mobile phone's remote data capabilities so that adoption of particular application components could be continuously monitored and components subsequently added or updated remotely. The cell phone intervention was delivered almost entirely via cell phone and was always-present, proactive, and interactive-providing passive and active reminders, frequent opportunities for knowledge dissemination, and multiple tools

Design of an ultra-thin dual band infrared system

Science.gov (United States)

Du, Ke; Cheng, Xuemin; Lv, Qichao; Hu, YiFei

2014-11-01

The ultra-thin imaging system using reflective multiple-fold structure has smaller volume and less weight while maintaining high resolution compared with conventional optical systems. The multi-folded approach can significantly extend focal distance within wide spectral range without incurring chromatic aberrations. In this paper, we present a dual infrared imaging system of four-folded reflection with two air-spaced concentric reflective surfaces. The dual brand IR system has 107mm effective focal length, 0.7NA, +/-4° FOV, and 50mm effective aperture with 80mm outer diameter into a 25mm total thickness, which spectral response is 3~12μm.

The Explicit Determinations Of Dual Plane Curves And Dual Helices In Terms Of Its Dual Curvature And Dual Torsion

OpenAIRE

Lee Jae Won; Choi Jin Ho; Jin Dae Ho

2014-01-01

In this paper, we give the explicit determinations of dual plane curves, general dual helices and dual slant helices in terms of its dual curvature and dual torsion as a fundamental theory of dual curves in a dual 3-space

Urban design for mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

2017-01-01

. In this paper, we shall explore the potential for a better understanding of contemporary urban challenges through the cross-disciplinary approach of ‘Mobilities design’. The paper investigates how this notion is based on an understanding of materialities and social action that is framed under the heading...

Optical design of low cost imaging systems for mobile medical applications

Science.gov (United States)

Kass, Alexander; Slyper, Ronit; Levitz, David

2015-03-01

Colposcopes, the gold standard devices for imaging the cervix at high magnfication, are expensive and sparse in low resource settings. Using a lens attachment, any smartphone camera can be turned into an imaging device for tissues such as the cervix. We create a smartphone-based colposcope using a simple lens design for high magnification. This particular design is useful because it allows parameters such as F-number, depth of field, and magnification to be controlled easily. We were therefore able to determine a set of design steps which are general to mobile medical imaging devices and allow them to maintain requisite image quality while still being rugged and affordable.

Power Management in Mobile Hydraulic Applications - An Approach for Designing Hydraulic Power Supply Systems

DEFF Research Database (Denmark)

Pedersen, Henrik Clemmensen

2004-01-01

Throughout the last three decades energy consumption has become one of the primary design aspects in hydraulic systems, especially for mobile hydraulic systems, as power and cooling capacity here is at limited disposal. Considering the energy usage, this is dependent on component efficiency, but ...... the hydraulic power supply in the most energy efficient way, when considering a number of load situations. Finally an example of the approach is shown to prove its validity.}......Throughout the last three decades energy consumption has become one of the primary design aspects in hydraulic systems, especially for mobile hydraulic systems, as power and cooling capacity here is at limited disposal. Considering the energy usage, this is dependent on component efficiency...

Secure steganography designed for mobile platforms

Science.gov (United States)

Agaian, Sos S.; Cherukuri, Ravindranath; Sifuentes, Ronnie R.

2006-05-01

Adaptive steganography, an intelligent approach to message hiding, integrated with matrix encoding and pn-sequences serves as a promising resolution to recent security assurance concerns. Incorporating the above data hiding concepts with established cryptographic protocols in wireless communication would greatly increase the security and privacy of transmitting sensitive information. We present an algorithm which will address the following problems: 1) low embedding capacity in mobile devices due to fixed image dimensions and memory constraints, 2) compatibility between mobile and land based desktop computers, and 3) detection of stego images by widely available steganalysis software [1-3]. Consistent with the smaller available memory, processor capabilities, and limited resolution associated with mobile devices, we propose a more magnified approach to steganography by focusing adaptive efforts at the pixel level. This deeper method, in comparison to the block processing techniques commonly found in existing adaptive methods, allows an increase in capacity while still offering a desired level of security. Based on computer simulations using high resolution, natural imagery and mobile device captured images, comparisons show that the proposed method securely allows an increased amount of embedding capacity but still avoids detection by varying steganalysis techniques.

Automated positioning dual-axis solar tracking system with precision elevation and azimuth angle control

International Nuclear Information System (INIS)

Sidek, M.H.M.; Azis, N.; Hasan, W.Z.W.; Ab Kadir, M.Z.A.; Shafie, S.; Radzi, M.A.M.

2017-01-01

This paper presents a study on an automated positioning open-loop dual-axis solar tracking system. The solar tracker was designed and fabricated using standard cylindrical aluminium hollow and Polyuthrene (PE). The control system of the solar tracker was governed by Micro Controller Unit (MCU) with auxiliary devices which includes encoder and Global Positioning System (GPS). The sun path trajectory algorithm utilizing the astronomical equation and GPS information was also embedded in the system. The power generation performance of the dual-axis solar tracking system was compared with the fixed-tilted Photovoltaic (PV) system. It is found that the solar tracker is able to position itself automatically based on sun path trajectory algorithm with an accuracy of ±0.5°. The embedded Proportional Integral Derivative (PID) positioning system improves the tracking of elevation and azimuth angles with minimum energy consumption. It is reveals that the proposed solar tracker is able generate 26.9% and 12.8% higher power than fixed-tilted PV system on a clear and heavy overcast conditions respectively. Overall, the open-loop dual-axis solar tracker can be deployed automatically at any location on the earth with minimal configurations and is suitable for mobile solar tracking system. - Highlights: • Self-positioning dual-axis solar tracking system. • Precise control of elevation and azimuth angle. • Sun path trajectory based on astronomical equation and GPS. • Can achieve up to 26.9% higher power than fixed-tilted PV system under clear weather condition.

Expanding Horizons for Students with Dyslexia in the 21st Century: Universal Design and Mobile Technology

Science.gov (United States)

Reid, Gavin; Strnadova, Iva; Cumming, Therese

2013-01-01

This paper discusses the role of mobile technology in supporting people with dyslexia within the theoretical framework of Universal Design for Learning. The authors discuss how students with dyslexia can use mobile technology to address a diverse range of academic needs (such as reading, composing text, notetaking, metacognition and studying…

Dual-sided electrosurgery handpiece for simultaneous tissue cutting and coagulation: first report on a conceptual design validated by an animal experiment.

Science.gov (United States)

Tawfik, Hatem A; Fouad, Yousef A; Hafez, Rashad

2015-01-01

To introduce and evaluate the safety of a novel dual-sided electrosurgery handpiece design for simultaneous tissue cutting and coagulation. We designed a prototype double-sided handpiece allowing automatic switching between two electrodes with a simple handpiece flip. The concept of the system as a surgical instrument was assessed by an animal experiment. The skin of 15 Wistar albino white rats could be successfully incised and coagulated using both ends of the handpiece, thereby confirming the prospects and clinical applications of the system. The dual-sided electrosurgery handpiece is a simple and safe alternative to the traditional electrosurgery pencil, allowing the simultaneous use of two electrodes without the hassle of frequent electrode replacement.

Measuring the post-adoption customer perception of mobile banking services.

Science.gov (United States)

Yu, Tai-Kuei; Fang, Kwoting

2009-02-01

With liberalization and internalization in the financial market and progress in information technology, banks face dual competitive pressures to provide service quality and administrative efficiency. That these recent developments are fueled by technology might misleadingly suggest that the adoption of mobile banking is largely based on technological criteria. The purpose of this study is to establish a better measurement model for postadoption user perception of mobile banking services. Based on 458 valid responses of mobile banking users, the results show that the instrument, consisting of 21 items and 6 factors, is a reliable, valid, and useful measurement for assessing the postadoption perception of mobile banking.

Dual-wavelength DFB quantum cascade lasers: sources for multi-species trace gas spectroscopy

Science.gov (United States)

Kapsalidis, Filippos; Shahmohammadi, Mehran; Süess, Martin J.; Wolf, Johanna M.; Gini, Emilio; Beck, Mattias; Hundt, Morten; Tuzson, Béla; Emmenegger, Lukas; Faist, Jérôme

2018-06-01

We report on the design, fabrication, and performance of dual-wavelength distributed-feedback (DFB) quantum cascade lasers (QCLs) emitting at several wavelengths in the mid-infrared (mid-IR) spectrum. In this work, two new designs are presented: for the first one, called "Neighbour" DFB, two single-mode DFB QCLs are fabricated next to each other, with minimal lateral distance, to allow efficient beam-coupling into multi-pass gas cells. In addition, the minimal distance allows either laser to be used as an integrated heater for the other, allowing to extend the tuning range of its neighbour without any electrical cross-talk. For the second design, the Vernier effect was used to realize a switchable DFB laser, with two target wavelengths which are distant by about 300 cm^{-1}. These devices are promising laser sources for Tunable Diode Laser Absorption Spectroscopy applications targeting simultaneous detection of multiple gasses, with distant spectral features, in compact and mobile setups.

Dual mobility cups for preventing early hip arthroplasty dislocation in patients at risk: experience in a county hospital

Directory of Open Access Journals (Sweden)

Sebastian S. Mukka

2013-06-01

Full Text Available Dislocation remains a major concern after hip arthroplasty. We asked whether dual mobility cups (DMC would improve early hip stability in patients with high risk of dislocation. We followed 34 patients (21 females, 13 males treated between 2009 and 2012 with cemented DMC for hip revisions caused recurrent hip prosthetic dislocation or as a primary procedure in patients with high risk of instability. Functional outcome and quality of life were evaluated using Harris Hip Score and EQ-5D respectively. We found that the cemented DMC gave stability in 94%. Seven patients (20% were re-operated due to infection. One patient sustained a periprosthetic fracture. At follow-up (6 to 36 months, mean 18, the mean Harris hip score was 67 (standard deviation: 14 and mean EQ-5D was 0.76 (standard deviation: 0.12. We concluded that treating patients with high risk of dislocation with DMC can give good stability. However, complications such as postoperative infection can be frequent and should be managed carefully.

A mobile Nursing Information System based on human-computer interaction design for improving quality of nursing.

Science.gov (United States)

Su, Kuo-Wei; Liu, Cheng-Li

2012-06-01

A conventional Nursing Information System (NIS), which supports the role of nurse in some areas, is typically deployed as an immobile system. However, the traditional information system can't response to patients' conditions in real-time, causing delays on the availability of this information. With the advances of information technology, mobile devices are increasingly being used to extend the human mind's limited capacity to recall and process large numbers of relevant variables and to support information management, general administration, and clinical practice. Unfortunately, there have been few studies about the combination of a well-designed small-screen interface with a personal digital assistant (PDA) in clinical nursing. Some researchers found that user interface design is an important factor in determining the usability and potential use of a mobile system. Therefore, this study proposed a systematic approach to the development of a mobile nursing information system (MNIS) based on Mobile Human-Computer Interaction (M-HCI) for use in clinical nursing. The system combines principles of small-screen interface design with user-specified requirements. In addition, the iconic functions were designed with metaphor concept that will help users learn the system more quickly with less working-memory. An experiment involving learnability testing, thinking aloud and a questionnaire investigation was conducted for evaluating the effect of MNIS on PDA. The results show that the proposed MNIS is good on learning and higher satisfaction on symbol investigation, terminology and system information.

From conception to evaluation of mobile services for people with head injury: A participatory design perspective.

Science.gov (United States)

Groussard, Pierre-Yves; Pigot, Hélène; Giroux, Sylvain

2018-07-01

Adults with cognitive impairments lack the means to organise their daily life, plan their appointments, cope with fatigue, and manage their budget. They manifest interest in using new technologies to be part of society. Unfortunately, the applications offered on smart phones are often beyond their cognitive abilities. The goal of this study was to design a mobile cognitive assistant to enhance autonomy of people living with acquired traumatic brain injury. Participatory design methodologies guided this research by involving adults with cognitive impairments (CI) and their caregivers in the early stages of the design process. The population of the study is composed of four male adults who present cognitive impairments (three with head injury and one with stroke) and three caregivers. The first phase of this research was to design the Services Assistance Mobile and Intelligent (SAMI) application based on the needs expressed by the participants. During three focus groups, needs emerged concerning planning, health monitoring and money management and led to the implementation of assistive solutions on an Android mobile phone. During the second phase, the participants evaluated the mobile assistant SAMI at home for eight weeks. The results demonstrate that the participants were able to participate actively in the conception of SAMI and to use it successfully. People with CI showed a slight improvement in their life satisfaction. Due to the small number of participants, these promising results need to be confirmed by a larger-scale study.

Enhanced electrical properties of dual-layer channel ZnO thin film transistors prepared by atomic layer deposition

Science.gov (United States)

Li, Huijin; Han, Dedong; Dong, Junchen; Yu, Wen; Liang, Yi; Luo, Zhen; Zhang, Shengdong; Zhang, Xing; Wang, Yi

2018-05-01

The thin film transistors (TFTs) with a dual-layer channel structure combing ZnO thin layer grown at 200 °C and ZnO film grown at 120 °C by atomic layer deposition are fabricated. The dual-layer channel TFT exhibits a low leakage current of 2.8 × 10-13 A, Ion/Ioff ratio of 3.4 × 109, saturation mobility μsat of 12 cm2 V-1 s-1, subthreshold swing (SS) of 0.25 V/decade. The SS value decreases to 0.18 V/decade after the annealing treatment in O2 due to the reduction of the trap states at the channel/dielectric interface and in the bulk channel layer. The enhanced performance obtained from the dual-layer channel TFTs is due to the ability of maintaining high mobility and suppressing the increase in the off-current at the same time.

Dual source and dual detector arrays tetrahedron beam computed tomography for image guided radiotherapy

Science.gov (United States)

Kim, Joshua; Lu, Weiguo; Zhang, Tiezhi

2014-02-01

Cone-beam computed tomography (CBCT) is an important online imaging modality for image guided radiotherapy. But suboptimal image quality and the lack of a real-time stereoscopic imaging function limit its implementation in advanced treatment techniques, such as online adaptive and 4D radiotherapy. Tetrahedron beam computed tomography (TBCT) is a novel online imaging modality designed to improve on the image quality provided by CBCT. TBCT geometry is flexible, and multiple detector and source arrays can be used for different applications. In this paper, we describe a novel dual source-dual detector TBCT system that is specially designed for LINAC radiation treatment machines. The imaging system is positioned in-line with the MV beam and is composed of two linear array x-ray sources mounted aside the electrical portal imaging device and two linear arrays of x-ray detectors mounted below the machine head. The detector and x-ray source arrays are orthogonal to each other, and each pair of source and detector arrays forms a tetrahedral volume. Four planer images can be obtained from different view angles at each gantry position at a frame rate as high as 20 frames per second. The overlapped regions provide a stereoscopic field of view of approximately 10-15 cm. With a half gantry rotation, a volumetric CT image can be reconstructed having a 45 cm field of view. Due to the scatter rejecting design of the TBCT geometry, the system can potentially produce high quality 2D and 3D images with less radiation exposure. The design of the dual source-dual detector system is described, and preliminary results of studies performed on numerical phantoms and simulated patient data are presented.

User-centered design of a mobile medication management.

Science.gov (United States)

Sedlmayr, Brita; Schöffler, Jennifer; Prokosch, Hans-Ulrich; Sedlmayr, Martin

2018-03-05

The use of a nationwide medication plan has been promoted as an effective strategy to improve patient safety in Germany. However, the medication plan only exists as a paper-based version, which is related to several problems, that could be circumvented by an electronic alternative. The main objective of this study was to report on the development of a mobile interface concept to support the management of medication information. The human-centered design (UCD) process was chosen. First the context of use was analyzed, and personas and an interaction concept were designed. Next, a paper prototype was developed and evaluated by experts. Based on those results, a medium-fidelity prototype was created and assessed by seven end-users who performed a thinking-aloud test in combination with a questionnaire based on the System Usability Scale (SUS). Initially for one persona/user type, an interface design concept was developed, which received an average SUS-Score of 92.1 in the user test. Usability problems have been solved so that the design concept could be fixed for a future implementation. Contribution: The approach of the UCD process and the methods involved can be applied by other researchers as a framework for the development of similar applications.

Common Mobile Learning Characteristics--An Analysis of Mobile Learning Models and Frameworks

Science.gov (United States)

Imtinan, Umera; Chang, Vanessa; Issa, Tomayess

2013-01-01

Mobile learning offers learning opportunities to learners without the limitations of time and space. Mobile learning has introduced a number of flexible options to the learners across disciplines and at different educational levels. However, designing mobile learning content is an equally challenging task for the instructional designers.…

Tactics for Homing in Mobile LifeTactics for Homing in Mobile Life

DEFF Research Database (Denmark)

Petersen, Marianne Graves; Borup Lynggaard, Aviaja; Winther, Ida Wentzel

we argue that several of the tactics identified are currently not well supported. We discuss how technology design can learn from this study through pointing to the potential in designing mobile technologies to better support these unsupported tactics. We consider the tactics as a tool for deeper...... studies of extremely mobile people we identify general tactics for homing. We present the identified tactics and show how people deploy not only one but several tactics in their intention of making a homely feeling despite not being in their primary home. Reviewing the mobile technologies currently in use...... understanding of mobile practices and thus informing the design of more relevant future technologies for people engaged in a mobile lifestyle....

Design and recognition of artificial landmarks for reliable indoor self-localization of mobile robots

Directory of Open Access Journals (Sweden)

Xu Zhong

2017-02-01

Full Text Available This article presents a self-localization scheme for indoor mobile robot navigation based on reliable design and recognition of artificial visual landmarks. Each landmark is patterned with a set of concentric circular rings in black and white, which reliably encodes the landmark’s identity under environmental illumination. A mobile robot in navigation uses an onboard camera to capture landmarks in the environment. The landmarks in an image are detected and identified using a bilayer recognition algorithm: A global recognition process initially extracts candidate landmark regions across the whole image and tries to identify enough landmarks; if necessary, a local recognition process locally enhances those unidentified regions of interest influenced by illumination and incompleteness and reidentifies them. The recognized landmarks are used to estimate the position and orientation of the onboard camera in the environment, based on the geometric relationship between the image and environmental frames. The experiments carried out in a real indoor environment show high robustness of the proposed landmark design and recognition scheme to the illumination condition, which leads to reliable and accurate mobile robot localization.

Practical Eco-Design and Eco-Innovation of Consumer Electronics—the Case of Mobile Phones

Directory of Open Access Journals (Sweden)

Anders S. G. Andrae

2016-02-01

Full Text Available Annually, it is estimated that about 4 billion units of consumer electronics for mobile communications are produced worldwide. This could lead to various ecological imbalances unless the design and disposal of the products are handled optimally. To illustrate how industry looks at and responds to the increasing social awareness, this article describes how sustainability is successfully implemented in practice at a large Chinese company, developing and producing various kinds of electronic products used for communication. It also describes how a variety of eco-innovations and business models contribute to reducing the environmental impact; for example, through increased recovery and recycling. A new kind of eco-design procedure is presented along with a new methodology which shows how a mobile phone gradually becomes more sustainable from one generation to the next. The issues with and set-up of new eco-labeling schemes for mobile phones, eco-rating, is described in detail. The conclusion is that due to high competition between companies, the industry acts resourcefully and a lot is done to the save the ecological environment.

Dual design resistor for high voltage conditioning and transmission lines

Science.gov (United States)

Siggins, Timothy Lynn [Newport News, VA; Murray, Charles W [Hayes, VA; Walker, Richard L [Norfolk, VA

2007-01-23

A dual resistor for eliminating the requirement for two different value resistors. The dual resistor includes a conditioning resistor at a high resistance value and a run resistor at a low resistance value. The run resistor can travel inside the conditioning resistor. The run resistor is capable of being advanced by a drive assembly until an electrical path is completed through the run resistor thereby shorting out the conditioning resistor and allowing the lower resistance run resistor to take over as the current carrier.

Designing thiophene-based azomethine oligomers with tailored properties: Self-assembly and charge carrier mobility

DEFF Research Database (Denmark)

Kiriy, N.; Bocharova, V.; Kiriy, A.

2004-01-01

This paper describes synthesis and characterization of two thiophene-based azomethines designed to optimize solubility, self-assembly, and charge carrier mobility. We found that incorporation of azomethine and amide moieties in the alpha,omega-position, and hexyl chains in the beta-position of th...... with the mobilities of the best organic semiconductors. All these significant differences in properties of related compounds can be attributed to the hydrogen bonding between QT-amide molecules responsible for the observed self-assembly....

Design and fabrication of a diffractive beam splitter for dual-wavelength and concurrent irradiation of process points.

Science.gov (United States)

Amako, Jun; Shinozaki, Yu

2016-07-11

We report on a dual-wavelength diffractive beam splitter designed for use in parallel laser processing. This novel optical element generates two beam arrays of different wavelengths and allows their overlap at the process points on a workpiece. To design the deep surface-relief profile of a splitter using a simulated annealing algorithm, we introduce a heuristic but practical scheme to determine the maximum depth and the number of quantization levels. The designed corrugations were fabricated in a photoresist by maskless grayscale exposure using a high-resolution spatial light modulator. We characterized the photoresist splitter, thereby validating the proposed beam-splitting concept.

A Novel WPT System Based on Dual Transmitters and Dual Receivers for High Power Applications: Analysis, Design and Implementation

Directory of Open Access Journals (Sweden)

Yong Li

2017-02-01

Full Text Available Traditional Wireless Power Transfer (WPT systems only have one energy transmission path, which can hardly meet the power demand for high power applications, e.g., railway applications (electric trains and trams, etc. due to the capacity constraints of power electronic devices. A novel WPT system based on dual transmitters and dual receivers is proposed in this paper to upgrade the power capacity of the WPT system. The reliability and availability of the proposed WPT system can be dramatically improved due to the four energy transmission paths. A three-dimensional finite element analysis (FEA tool ANSYS MAXWELL (ANSYS, Canonsburg, PA, USA is adopted to investigate the proposed magnetic coupling structure. Besides, the effects of the crossing coupling mutual inductances among the transmitters and receivers are analyzed. It shows that the same-side cross couplings will decrease the efficiency and transmitted power. Decoupling transformers are employed to mitigate the effects of the same-side cross couplings. Meanwhile, the output voltage in the secondary side can be regulated at its designed value with a fast response performance, and the system can continue work even with a faulty inverter. Finally, a scale-down experimental setup is provided to verify the proposed approach. The experimental results indicate that the proposed method could improve the transmitted power capacity, overall efficiency and reliability, simultaneously. The proposed WPT structure is a potential alternative for high power applications.

Switchable dual-wavelength single-longitudinal-mode erbium fiber laser utilizing a dual-ring scheme with a saturable absorber

Science.gov (United States)

Yang, Zi-Qing; Huang, Tzu-Jung; Chang, Yao-Jen; Yeh, Chien-Hung; Chow, Chi-Wai; Chen, Jing-Heng; Chen, Kun-Huang

2018-06-01

In this work, we propose and demonstrate a switchable dual-wavelength erbium-doped fiber (EDF) ring laser with stable single-longitudinal-mode (SLM) output. Here, a dual-ring (DR) structure with an unpumped EDF of 2 m is designed to achieve SLM oscillation. Five fiber Bragg gratings (FBGs) are applied in the laser cavity serving as the reflective element to generate different dual-wavelength outputs. In the measurement, six sets of generated dual-wavelengths with various mode-spacing (Δλ) can be achieved via the five FBGs. Additionally, the stability performance of the proposed EDF DR laser is also demonstrated.

Mobile Learning and Integration of Mobile Technologies in Education

Science.gov (United States)

Keengwe, Jared; Bhargava, Malini

2014-01-01

Mobile technologies have a huge potential to transform education provided these technologies are designed and implemented in such a way that they are relevant to the social and cultural context of learning. Clearly, the application, implementation, and design of mobile technology in the global educational context pose technological and…

Combining ethnography and object-orientation for mobile interaction design

DEFF Research Database (Denmark)

Kjeldskov, Jesper; Stage, Jan

2012-01-01

There has been a lot of interest in ethnography within human–computer interaction over the last two decades, and its relevance within systems development is today beyond question. However, one of the challenges reported is that ethnography generates findings and knowledge with such contextual...... richness that it can be hard to transfer into system design. In the light of recent years' push for the use of ethnography within the area of mobile human–computer interaction, this challenge has resurfaced and is of renewed importance to the research field. In this article we describe an interdisciplinary...

Design and Analysis of a Data Fusion Scheme in Mobile Wireless Sensor Networks Based on Multi-Protocol Mobile Agents.

Science.gov (United States)

Wu, Chunxue; Wu, Wenliang; Wan, Caihua; Bekkering, Ernst; Xiong, Naixue

2017-11-03

Sensors are increasingly used in mobile environments with wireless network connections. Multiple sensor types measure distinct aspects of the same event. Their measurements are then combined to produce integrated, reliable results. As the number of sensors in networks increases, low energy requirements and changing network connections complicate event detection and measurement. We present a data fusion scheme for use in mobile wireless sensor networks with high energy efficiency and low network delays, that still produces reliable results. In the first phase, we used a network simulation where mobile agents dynamically select the next hop migration node based on the stability parameter of the link, and perform the data fusion at the migration node. Agents use the fusion results to decide if it should return the fusion results to the processing center or continue to collect more data. In the second phase. The feasibility of data fusion at the node level is confirmed by an experimental design where fused data from color sensors show near-identical results to actual physical temperatures. These results are potentially important for new large-scale sensor network applications.

Design and experimental verification of a dual-band metamaterial filter

Science.gov (United States)

Zhu, Hong-Yang; Yao, Ai-Qin; Zhong, Min

2016-10-01

In this paper, we present the design, simulation, and experimental verification of a dual-band free-standing metamaterial filter operating in a frequency range of 1 THz-30 THz. The proposed structure consists of periodically arranged composite air holes, and exhibits two broad and flat transmission bands. To clarify the effects of the structural parameters on both resonant transmission bands, three sets of experiments are performed. The first resonant transmission band shows a shift towards higher frequency when the side width w 1 of the main air hole is increased. In contrast, the second resonant transmission band displays a shift towards lower frequency when the side width w 2 of the sub-holes is increased, while the first resonant transmission band is unchanged. The measured results indicate that these resonant bands can be modulated individually by simply optimizing the relevant structural parameters (w 1 or w 2) for the required band. In addition, these resonant bands merge into a single resonant band with a bandwidth of 7.7 THz when w 1 and w 2 are optimized simultaneously. The structure proposed in this paper adopts different resonant mechanisms for transmission at different frequencies and thus offers a method to achieve a dual-band and low-loss filter. Project supported by the Doctorate Scientific Research Foundation of Hezhou University, China (Grant No. HZUBS201503), the Promotion of the Basic Ability of Young and Middle-aged Teachers in Universities Project of Guangxi Zhuang Autonomous Region, China (Grant No. KY2016YB453), the Guangxi Colleges and Universities Key Laboratory Symbolic Computation, China, Engineering Data Processing and Mathematical Support Autonomous Discipline Project of Hezhou University, China (Grant No. 2016HZXYSX01).

Design of two-DMD based zoom MW and LW dual-band IRSP using pixel fusion

Science.gov (United States)

Pan, Yue; Xu, Xiping; Qiao, Yang

2018-06-01

In order to test the anti-jamming ability of mid-wave infrared (MWIR) and long-wave infrared (LWIR) dual-band imaging system, a zoom mid-wave (MW) and long-wave (LW) dual-band infrared scene projector (IRSP) based on two-digital micro-mirror device (DMD) was designed by using a projection method of pixel fusion. Two illumination systems, which illuminate the two DMDs directly with Kohler telecentric beam respectively, were combined with projection system by a spatial layout way. The distances of projection entrance pupil and illumination exit pupil were also analyzed separately. MWIR and LWIR virtual scenes were generated respectively by two DMDs and fused by a dichroic beam combiner (DBC), resulting in two radiation distributions in projected image. The optical performance of each component was evaluated by ray tracing simulations. Apparent temperature and image contrast were demonstrated by imaging experiments. On the basis of test and simulation results, the aberrations of optical system were well corrected, and the quality of projected image meets test requirements.

Design of radio frequency power amplifiers for cellular phones and base stations in modern mobile communication systems

OpenAIRE

Wu, Lei

2009-01-01

The mobile radio communication has begun with Guglielmo Marconi's and Alexander Popov's experiments with ship-to-shore communication in the 1890's. Land mobile radio telephone systems have been used since the Detroit City Police Department installed the first wireless communication system in 1921. Since that time, radio systems have become more and more important for both voice and data communication. The modern mobile communication systems are mainly designed in high frequency ranges due...

Person mobility in the design and analysis of cluster-randomized cohort prevention trials.

Science.gov (United States)

Vuchinich, Sam; Flay, Brian R; Aber, Lawrence; Bickman, Leonard

2012-06-01

Person mobility is an inescapable fact of life for most cluster-randomized (e.g., schools, hospitals, clinic, cities, state) cohort prevention trials. Mobility rates are an important substantive consideration in estimating the effects of an intervention. In cluster-randomized trials, mobility rates are often correlated with ethnicity, poverty and other variables associated with disparity. This raises the possibility that estimated intervention effects may generalize to only the least mobile segments of a population and, thus, create a threat to external validity. Such mobility can also create threats to the internal validity of conclusions from randomized trials. Researchers must decide how to deal with persons who leave study clusters during a trial (dropouts), persons and clusters that do not comply with an assigned intervention, and persons who enter clusters during a trial (late entrants), in addition to the persons who remain for the duration of a trial (stayers). Statistical techniques alone cannot solve the key issues of internal and external validity raised by the phenomenon of person mobility. This commentary presents a systematic, Campbellian-type analysis of person mobility in cluster-randomized cohort prevention trials. It describes four approaches for dealing with dropouts, late entrants and stayers with respect to data collection, analysis and generalizability. The questions at issue are: 1) From whom should data be collected at each wave of data collection? 2) Which cases should be included in the analyses of an intervention effect? and 3) To what populations can trial results be generalized? The conclusions lead to recommendations for the design and analysis of future cluster-randomized cohort prevention trials.

Design and Implementation of Modular Software for Programming Mobile Robots

Directory of Open Access Journals (Sweden)

Alessandro Farinelli

2006-03-01

Full Text Available This article describes a software development toolkit for programming mobile robots, that has been used on different platforms and for different robotic applications. We address design choices, implementation issues and results in the realization of our robot programming environment, that has been devised and built from many people since 1998. We believe that the proposed framework is extremely useful not only for experienced robotic software developers, but also for students approaching robotic research projects.

Designing Multimodal Mobile Interaction for a Text Messaging Application for Visually Impaired Users

Directory of Open Access Journals (Sweden)

Carlos Duarte

2017-12-01

Full Text Available While mobile devices have experienced important accessibility advances in the past years, people with visual impairments still face important barriers, especially in specific contexts when both their hands are not free to hold the mobile device, like when walking outside. By resorting to a multimodal combination of body based gestures and voice, we aim to achieve full hands and vision free interaction with mobile devices. In this article, we describe this vision and present the design of a prototype, inspired by that vision, of a text messaging application. The article also presents a user study where the suitability of the proposed approach was assessed, and a performance comparison between our prototype and existing SMS applications was conducted. Study participants received positively the prototype, which also supported better performance in tasks that involved text editing.

Design and development of CAMAC 12 bit ADC/DAC dual purpose module

International Nuclear Information System (INIS)

Kulkarni, S.G.; Gore, J.A.; Ramlal, V.; Matkar, U.V.; Lokare, R.N.; Yadav, M.L.; Ekambaram, M.; Gupta, A.K.; Datar, V.M.

2013-01-01

A dual function CAMAC module is designed for Pelletron Accelerator which can function as 12 bit 8 channels DAC or 12 bit 16 channels ADC. Spartan 2 series of FPGA is used for implementing the CAMAC interface logic as well as logic for ADC/DAC interface. The PCB has both the ADC and DAC mounted but the module can have only one function selected due to wiring constraint. Two different VHDL programs (one for the ADC and other for the DAC) reside on the EEPROM permitting selection of any one as per the functionality required. The module is working as a 12 bit DAC at BARC-TIFR Pelletron Linac Facility, successfully. (author)

DESIGN AND DEVELOPMENT OF MOBILE LEARNING APPLICATIONS USING DRUPAL

Directory of Open Access Journals (Sweden)

N.M.A.E.D Wirastuti

2010-07-01

Full Text Available The growth of the mobile industry is an important aspect in the link of the global village. Another aspect is theInternet. The introduction of VoIP, video conferencing, emailing and TV reviewing also support the communicationbecoming much easier. The Internet becomes a reliable source of information; Users learn more from the Internetthan anywhere else. Therefore, there are many educational institutions publishing their learning material on theInternet. So that e-learning becomes an essential learning method now days. Student can access the learning materialeverywhere, every time. While the mobile industry offers many 3G services, mobile operators still lack of theapplication that allowing users to access learning material while on the move. Mobile learning is an excellentsolution to solve this problem. This will be supported by mobile features improvement, cheaper and faster data rates.This paper gives a simple idea of developing mobile learning where users can access learning material in similarway to blackboard via mobile devices, called blackboard mobile.

User interface design for mobile-based sexual health interventions for young people: design recommendations from a qualitative study on an online Chlamydia clinical care pathway.

Science.gov (United States)

Gkatzidou, Voula; Hone, Kate; Sutcliffe, Lorna; Gibbs, Jo; Sadiq, Syed Tariq; Szczepura, Ala; Sonnenberg, Pam; Estcourt, Claudia

2015-08-26

The increasing pervasiveness of mobile technologies has given potential to transform healthcare by facilitating clinical management using software applications. These technologies may provide valuable tools in sexual health care and potentially overcome existing practical and cultural barriers to routine testing for sexually transmitted infections. In order to inform the design of a mobile health application for STIs that supports self-testing and self-management by linking diagnosis with online care pathways, we aimed to identify the dimensions and range of preferences for user interface design features among young people. Nine focus group discussions were conducted (n = 49) with two age-stratified samples (16 to 18 and 19 to 24 year olds) of young people from Further Education colleges and Higher Education establishments. Discussions explored young people's views with regard to: the software interface; the presentation of information; and the ordering of interaction steps. Discussions were audio recorded and transcribed verbatim. Interview transcripts were analysed using thematic analysis. Four over-arching themes emerged: privacy and security; credibility; user journey support; and the task-technology-context fit. From these themes, 20 user interface design recommendations for mobile health applications are proposed. For participants, although privacy was a major concern, security was not perceived as a major potential barrier as participants were generally unaware of potential security threats and inherently trusted new technology. Customisation also emerged as a key design preference to increase attractiveness and acceptability. Considerable effort should be focused on designing healthcare applications from the patient's perspective to maximise acceptability. The design recommendations proposed in this paper provide a valuable point of reference for the health design community to inform development of mobile-based health interventions for the diagnosis

Dual source and dual detector arrays tetrahedron beam computed tomography for image guided radiotherapy

International Nuclear Information System (INIS)

Kim, Joshua; Zhang, Tiezhi; Lu, Weiguo

2014-01-01

Cone-beam computed tomography (CBCT) is an important online imaging modality for image guided radiotherapy. But suboptimal image quality and the lack of a real-time stereoscopic imaging function limit its implementation in advanced treatment techniques, such as online adaptive and 4D radiotherapy. Tetrahedron beam computed tomography (TBCT) is a novel online imaging modality designed to improve on the image quality provided by CBCT. TBCT geometry is flexible, and multiple detector and source arrays can be used for different applications. In this paper, we describe a novel dual source–dual detector TBCT system that is specially designed for LINAC radiation treatment machines. The imaging system is positioned in-line with the MV beam and is composed of two linear array x-ray sources mounted aside the electrical portal imaging device and two linear arrays of x-ray detectors mounted below the machine head. The detector and x-ray source arrays are orthogonal to each other, and each pair of source and detector arrays forms a tetrahedral volume. Four planer images can be obtained from different view angles at each gantry position at a frame rate as high as 20 frames per second. The overlapped regions provide a stereoscopic field of view of approximately 10–15 cm. With a half gantry rotation, a volumetric CT image can be reconstructed having a 45 cm field of view. Due to the scatter rejecting design of the TBCT geometry, the system can potentially produce high quality 2D and 3D images with less radiation exposure. The design of the dual source–dual detector system is described, and preliminary results of studies performed on numerical phantoms and simulated patient data are presented. (paper)

The Design and Development of an Omni-Directional Mobile Robot Oriented to an Intelligent Manufacturing System.

Science.gov (United States)

Qian, Jun; Zi, Bin; Wang, Daoming; Ma, Yangang; Zhang, Dan

2017-09-10

In order to transport materials flexibly and smoothly in a tight plant environment, an omni-directional mobile robot based on four Mecanum wheels was designed. The mechanical system of the mobile robot is made up of three separable layers so as to simplify its combination and reorganization. Each modularized wheel was installed on a vertical suspension mechanism, which ensures the moving stability and keeps the distances of four wheels invariable. The control system consists of two-level controllers that implement motion control and multi-sensor data processing, respectively. In order to make the mobile robot navigate in an unknown semi-structured indoor environment, the data from a Kinect visual sensor and four wheel encoders were fused to localize the mobile robot using an extended Kalman filter with specific processing. Finally, the mobile robot was integrated in an intelligent manufacturing system for material conveying. Experimental results show that the omni-directional mobile robot can move stably and autonomously in an indoor environment and in industrial fields.

[Design of an anesthesia and micro-environment information management system in mobile operating room].

Science.gov (United States)

Wang, Xianwen; Liu, Zhiguo; Zhang, Wenchang; Wu, Qingfu; Tan, Shulin

2013-08-01

We have designed a mobile operating room information management system. The system is composed of a client and a server. A client, consisting of a PC, medical equipments, PLC and sensors, provides the acquisition and processing of anesthesia and micro-environment data. A server is a powerful computer that stores the data of the system. The client gathers the medical device data by using the C/S mode, and analyzes the obtained HL7 messages through the class library call. The client collects the micro-environment information with PLC, and finishes the data reading with the OPC technology. Experiment results showed that the designed system could manage the patient anesthesia and micro-environment information well, and improve the efficiency of the doctors' works and the digital level of the mobile operating room.

Design on a Composite Mobile System for Exploration Robot

Directory of Open Access Journals (Sweden)

Weiyan Shang

2016-01-01

Full Text Available In order to accomplish exploration missions in complex environments, a new type of robot has been designed. By analyzing the characteristics of typical moving systems, a new mobile system which is named wheel-tracked moving system (WTMS has been presented. Then by virtual prototype simulation, the new system’s ability to adapt complex environments has been verified. As the curve of centroid acceleration changes in large amplitude in this simulation, ride performance of this robot has been studied. Firstly, a simplified dynamic model has been established, and then by affecting factors analysis on ride performance, an optimization model for suspension parameters has been presented. Using NSGA-II method, a set of nondominated solutions for suspension parameters has been gotten, and by weighing the importance of the objective function, an optimal solution has been selected to be applied on suspension design. As the wheel-tracked exploration robot has been designed and manufactured, the property test has been conducted. By testing on physical prototype, the robot’s ability to surmount complex terrain has been verified. Design of the wheel-tracked robot will provide a stable platform for field exploration tasks, and in addition, the certain configuration and suspension parameters optimization method will provide reference to other robot designs.

Mobilization and Adaptation of a Rural Cradle-to-Career Network

Directory of Open Access Journals (Sweden)

Sarah J. Zuckerman

2016-10-01

Full Text Available This case study explored the development of a rural cradle-to-career network with a dual focus on the initial mobilization of network members and subsequent adaptations made to maintain mobilization, while meeting local needs. Data sources included interviews with network members, observations of meetings, and documentary evidence. Network-based social capital facilitated mobilization. Where networks were absent and where distrust and different values were evident, mobilization faltered. Three network adaptations were discovered: Special rural community organizing strategies, district-level action planning, and a theory of action focused on out-of-school factors. All three were attributable to the composition of mobilized stakeholders and this network’s rural social geography. These findings illuminate the importance of social geography in the development and advancement of rural cradle-to-career networks.

Mobile & social game design monetization methods and mechanics

CERN Document Server

Fields, Tim

2014-01-01

IntroductionThe Changing TideWhat This Book Is NotWhat Is a Social Game? Are Mobile Games Social? Meet Your CompetitionBBS Games and MUDsMMOsJust Being Multiplayer Doesn't Make You SocialGreat Mobile Games ARE SocialInterview with Words with Friends Creators, The BettnersHistory of Game MonetizationWhat Do We Mean By MonetizationA Brief History of Game MonetizationInterview with Richard Garriott, ""The Three Grand Eras of Gaming""Why Create a Social or Mobile Game?Social and Mobile Games Put a Lot of Power in the Hands of the DevelopersSocial Games Make the Developer ResponsibleSocial Games Gi

Fault Tolerant Control Architecture Design for Mobile Manipulation in Scientific Facilities

Directory of Open Access Journals (Sweden)

Mohammad M. Aref

2015-01-01

Full Text Available This paper describes one of the challenging issues implied by scientific infrastructures on a mobile robot cognition architecture. For a generally applicable cognition architecture, we study the dependencies and logical relations between several tasks and subsystems. The overall view of the software modules is described, including their relationship with a fault management module that monitors the consistency of the data flow among the modules. The fault management module is the solution of the deliberative architecture for the single point failures, and the safety anchor is the reactive solution for the faults by redundant equipment. In addition, a hardware architecture is proposed to ensure safe robot movement as a redundancy for the cognition of the robot. The method is designed for a four-wheel steerable (4WS mobile manipulator (iMoro as a case study.

Using a Studio-Based Pedagogy to Engage Students in the Design of Mobile-Based Media

Science.gov (United States)

Mathews, James M.

2010-01-01

The article presents a brief overview of the Neighbourhood Game Design Project, a studio-based curriculum intervention aimed at engaging students in the design of place-based mobile games and interactive stories using geo-locative technologies (for example, GPS enabled cell phones). It describes the three curricular components that defined the…