WorldWideScience

Sample records for du combustible point

  1. Multi-Point Combustion System: Final Report

    Science.gov (United States)

    Goeke, Jerry; Pack, Spencer; Zink, Gregory; Ryon, Jason

    2014-01-01

    A low-NOx emission combustor concept has been developed for NASA's Environmentally Responsible Aircraft (ERA) program to meet N+2 emissions goals for a 70,000 lb thrust engine application. These goals include 75 percent reduction of LTO NOx from CAEP6 standards without increasing CO, UHC, or smoke from that of current state of the art. An additional key factor in this work is to improve lean combustion stability over that of previous work performed on similar technology in the early 2000s. The purpose of this paper is to present the final report for the NASA contract. This work included the design, analysis, and test of a multi-point combustion system. All design work was based on the results of Computational Fluid Dynamics modeling with the end results tested on a medium pressure combustion rig at the UC and a medium pressure combustion rig at GRC. The theories behind the designs, results of analysis, and experimental test data will be discussed in this report. The combustion system consists of five radially staged rows of injectors, where ten small scale injectors are used in place of a single traditional nozzle. Major accomplishments of the current work include the design of a Multipoint Lean Direct Injection (MLDI) array and associated air blast and pilot fuel injectors, which is expected to meet or exceed the goal of a 75 percent reduction in LTO NOx from CAEP6 standards. This design incorporates a reduced number of injectors over previous multipoint designs, simplified and lightweight components, and a very compact combustor section. Additional outcomes of the program are validation that the design of these combustion systems can be aided by the use of Computational Fluid Dynamics to predict and reduce emissions. Furthermore, the staging of fuel through the individually controlled radially staged injector rows successfully demonstrated improved low power operability as well as improvements in emissions over previous multipoint designs. Additional comparison

  2. Automatic continuous dew point measurement in combustion gases

    Energy Technology Data Exchange (ETDEWEB)

    Fehler, D.

    1986-08-01

    Low exhaust temperatures serve to minimize energy consumption in combustion systems. This requires accurate, continuous measurement of exhaust condensation. An automatic dew point meter for continuous operation is described. The principle of measurement, the design of the measuring system, and practical aspects of operation are discussed.

  3. Promotion des droits de la personne et de la justice du point de vue ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Promotion des droits de la personne et de la justice du point de vue des pays du Sud. À l'heure où des pouvoirs émergents comme la Chine, l'Inde et le Brésil prennent du gallon sur les plans économique et politique, dans les pays du Sud, les organismes de la base s'unissent pour veiller au respect des droits de la ...

  4. Resistivity tomography of Pointe du Hoc cliffs for stability assessment

    Science.gov (United States)

    Udphuay, S.; Everett, M. E.; Warden, R.

    2008-12-01

    Pointe du Hoc WWII battlefield overlooking the English Channel in western Normandy, France, is an important cultural resource, being an integral component of the June 6 1944 D-Day invasion. Two major buildings, the forward observation post (OP) and Col. Rudder's command post (RCP), are now perched perilously close to the cliff's edge owing to six decades of cliff retreat. Geophysical surveys were carried out in March 2008 to investigate the risk of cliff failure and to inform possible geotechnical remediation strategies with a final goal toward re-opening the observation post that is now closed to visitors. The geophysical surveying is accomplished by high-resolution resistivity tomography, conducted in extreme topography and in the midst of dense cultural clutter. The results of the OP tomography indicate that the highest mass movement hazard is associated with the marine caverns at the base of the cliff at the point of strongest wave attack. These caverns occupy the future site of a sea arch which will threaten the OP building. There is a high probability of a soil wedge failure on the east facing cliff edge close to the OP building. Such a failure could damage or destroy the building. The possibility of a sudden catastrophic failure along any one of these fractures cannot be ruled out. The greatest risk at the RCP site, which is under less immediate threat, is associated with soil wedge failures at the top of the cliffs.

  5. Aspects chimiques de la combustion du charbon pulvérisé. Première partie Chemical Aspects of the Combustion of Pulverized Coal. Part One

    Directory of Open Access Journals (Sweden)

    De Soete G. G.

    2006-11-01

    deux mécanismes totalement différents, par exemple entre le mécanisme d'ignition homogène et le mécanisme d'ignition hétérogène du charbon, avec des conséquences pratiques pour la stabilisation de la flamme industrielle ; autre exemple : la compétition entre les divers mécanismes homogènes de formation d'oxydes d'azote et les mécanismes hétérogènes de leur réduction sur des particules solides de coke, de suie et de cendre. Avec ces idées présentes comme un leitmotiv implicite, on passe en revue les grandes étapes de la flamme industrielle de charbon pulvérisé : la dévolatilisation rapide avec la formation progressive de volatils gazeux, de goudrons et de coke ; la transformation partielle des produits gazeux et liquides de pyrolyse en suies ainsi que leur oxydation en phase gazeuse ; la combustion hétérogène du coke ; l'ignition du charbon et sa dépendance par rapport à des processus critiques homogènes et (ou hétérogènes. Comme exemple typique d'un épiphénomènechimique, on suit la transformation des espèces azotées en NO et en N2, qui se greffe en contrepoint et à chaque pas sur tes différents thèmes successifs de cette symphonie de l'oxydation du charbon. En de nombreux points de cette évolution du charbon à travers la flamme, les connaissances de la chimie de com-bustion en phase gazeuse constituent un instrument utile d'interprétation (par exemple : pour l'oxydation des volatils, pour la discussion des modalités d'ignition. II n'en reste pas moins vrai que la plupart des problèmes chimiques hétérogènes sont bien spécifiques de la flamme de charbon ; leur traitement est rendu ardu à cause de la complexité, évolutive au cours de la combustion, du combustible solide lui-même. It is not easy to obtain a full picture of the multiple chemical phenomena which occur inside a pulverized coal flame. This bibliographie review attempts to give more than just a juxtaposition of data from the recent literature and risks making

  6. Study of the aqueous chemical treatment of uranium zirconium fuels; Etude du traitement chimique des combustibles uraniumzirconium par voie seche

    Energy Technology Data Exchange (ETDEWEB)

    Bourgeois, M; Nollet, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-07-01

    A dry process has been studied for separating the uranium from the zirconium-either for recovering the enriched uranium from fuel element production waste, or with a view to treating this waste after irradiation. In this process the alloy is treated with hydrochloric acid at 400 deg. C in a fluidized corundum bed which causes the zirconium to volatilize as tetrachloride and the uranium to form the trichloride. This latter is then converted to the hexafluoride by attack with fluorure. After the laboratory tests, a first pilot plant with a capacity of 1 kg of alloy was tried out at the Fontenay-aux-Roses Nuclear Research Centre; this made it possible to fix the operational conditions for the process. An industrial scale plant was then built with the collaboration of the from Kuhlmann, and operated until a satisfactory process had been developed for treating the waste. This installation treats 3 kg/h of alloy with a yield for the hydrochloric acid of about 50 per cent and with a uranium loss in the zirconium tetrachloride of about 0.1 per cent. An active pilot plant capable of treating of treating a few kilos of irradiated alloy is now being studied. (authors) [French] On a etudie un procede de voie seche pour effectuer la separation de l'uranium et du zirconium - soit en vue de la recuperation de l'uranium enrichi contenu dans les dechets de fabrication des elements combustibles - soit en vue du traitement de ceux-ci apres irradiation. Ce procede consiste a attaquer l'alliage par l'acide chlorhydrique a 400 deg. C dans un lit fluidise de corindon, ce qui a pour effet de volatiliser le zirconium sous forme de tetrachlorure et de transformer l'uranium en trichlorure. Ce dernier est ensuite converti en hexafluorure par action du fluor. Apres des essais de laboratoire, un premier pilote a l'echelle de 1 kg d'alliage a ete experimente au Centre d'Etudes Nucleaires de Fontenay-aux-Roses et a permis de determiner les conditions operatoires du procede. En collaboration avec

  7. Measuring the exhaust gas dew point of continuously operated combustion plants

    Energy Technology Data Exchange (ETDEWEB)

    Fehler, D.

    1985-07-16

    Low waste-gas temperatures represent one means of minimizing the energy consumption of combustion facilities. However, condensation should be prevented to occur in the waste gas since this could result in a destruction of parts. Measuring the waste-gas dew point allows to control combustion parameters in such a way as to be able to operate at low temperatures without danger of condensation. Dew point sensors will provide an important signal for optimizing combustion facilities.

  8. Dosage of plutonium by isotopic dilution in irradiated fuels; Dosage du plutonium par dilution isotopique dans les combustibles irradies

    Energy Technology Data Exchange (ETDEWEB)

    Lucas, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    collaboration entre SECACI (Section d'Etudes Chimique et Analytique des Combustibles Irradies) et SSM (Section de Spectrometrie de Masse). SECACI a mis a notre disposition les locaux et le materiel necessaire dans ses laboratoires de Fontenay. Cette etude a mis en evidence l'importance du cycle de valence celui-ci doit permettre d'obtenir une repartition isotopique homogene dans les melanges echantillon-traceur et une separation U/Pu convenable. Or, nous avons constate que la presence d'un exces d'uranium modifie profondement la cinetique des reactions d'oxydo-reduction du plutonium. Nous avons donc ete amenes a changer certains points de la technique operatoire pour rendre ce cycle efficace et ameliorer de ce fait la separation U/Pu; la stabilite de l'emission thermoionique du plutonium, liee a la quantite d'uranium residuaire, a du meme coup ete amelioree, et, nous obtenons maintenant des analyses isotopiques plus precises. D'autre part, nous nous sommes efforces d'eliminer au maximum les contaminations isotopiques en employant un mode operatoire plus rationnel; le materiel utilise a fait l'objet d'une etude particuliere. Les evaporations sont conduites de facon a interdire l'existence de vapeurs saturantes a l'interieur des boites a gants. Le materiel qui ne peut etre change a chaque operation est soigneusement nettoye a chaque changement d'echantillons. Avec cette technique, un second etalonnage du traceur T{sub 2} a ete entrepris au moyen d'une nouvelle solution etalon. Preparee tres soigneusement, par pesee d'uranium et de plutonium de purete chimique connue, nous pensons que cette solution offre des garanties suffisantes pour servir de reference. La valeur du rapport {sup 233}U/{sup 242}Pu du traceur a ete obtenue avec une precision relative de 0,5 pour cent. Cette methode modifiee est appliquee actuellement a l'analyse des barreaux irradies dans G-3. (auteur)

  9. Vérification du point de vue des droits de la personne et de la paix ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Vérification du point de vue des droits de la personne et de la paix de la ... ou une nation prend le contrôle de la zone territoriale où il ou elle est installé(e). ... IWRA/CRDI sur les changements climatiques et la gestion adaptive de l'eau.

  10. Calage thermodynamique du point mort haut des moteurs à piston Thermodynamic Calibration of Top Dead Center in Piston Engines

    Directory of Open Access Journals (Sweden)

    Pinchon P.

    2006-11-01

    Full Text Available Lorsqu'on utilise un système d'acquisition rapide de données sur moteur, il se pose souvent le problème d'associer des grandeurs calculées, comme le volume de la chambre de combustion, à des grandeurs mesurées comme la pression dans le cylindre. II est alors indispensable de synchroniser avec une grande précision absolue ces deux grandeurs en repérant avec soin au moins un point de référence de la cinématique bielle-manivelle. Dans la méthode développée ici on a choisi de déterminer la position angulaire du vilebrequin correspondant au Point Mort Haut (PMH grâce à l'exploitation du signal de pression-cylindre acquis en compression-détente sans combustion, le moteur étant entraîné en rotation. Le principe du calage consiste à calculer l'écart existant entre le PMH et l'angle de la pression maximale qui est aisément repérable. Basée sur des considérations thermodynamiques théoriques, cette méthode de calage a été testée avec succès au cours d'essais effectués sur divers moteurs dont on a fait varier en particulier le rapport volumétrique, le remplissage et les pertes à la segmentation. La précision de la méthode est de l'ordre de 1/10e de degré de rotation vilebrequin. When a fast data-acquisition system is used for an engine, the problem often arises of associating both calculated data, such as combustion chamber volume, and measured data, such as pressure inside the cylinder. It then becomes indispensable to synchronize these two data with great absolute accuracy by carefully determining at least a reference point in the kinematics of the connecting-rod/crank shaft assembly. In the method developed here, we have chosen to determine the angular position of the crankshaft corresponding to top dead center (TDC by making use of the cylinder-pressure signal recorded during compression/expansion without combustion for motored engine. The calibration principle consists in calculating the shift between TDC and the

  11. Estimation of combustion flue gas acid dew point during heat recovery and efficiency gain

    Energy Technology Data Exchange (ETDEWEB)

    Bahadori, A. [Curtin University of Technology, Perth, WA (Australia)

    2011-06-15

    When cooling combustion flue gas for heat recovery and efficiency gain, the temperature must not be allowed to drop below the sulfur trioxide dew point. Below the SO{sub 3} dew point, very corrosive sulfuric acid forms and leads to operational hazards on metal surfaces. In the present work, simple-to-use predictive tool, which is easier than existing approaches, less complicated with fewer computations is formulated to arrive at an appropriate estimation of acid dew point during combustion flue gas cooling which depends on fuel type, sulfur content in fuel, and excess air levels. The resulting information can then be applied to estimate the acid dew point, for sulfur in various fuels up to 0.10 volume fraction in gas (0.10 mass fraction in liquid), excess air fractions up to 0.25, and elemental concentrations of carbon up to 3. The proposed predictive tool shows a very good agreement with the reported data wherein the average absolute deviation percent was found to be around 3.18%. This approach can be of immense practical value for engineers and scientists for a quick estimation of acid dew point during combustion flue gas cooling for heat recovery and efficiency gain for wide range of operating conditions without the necessity of any pilot plant setup and tedious experimental trials. In particular, process and combustion engineers would find the tool to be user friendly involving transparent calculations with no complex expressions for their applications.

  12. Combustion

    CERN Document Server

    Glassman, Irvin

    1987-01-01

    Combustion, Second Edition focuses on the underlying principles of combustion and covers topics ranging from chemical thermodynamics and flame temperatures to chemical kinetics, detonation, ignition, and oxidation characteristics of fuels. Diffusion flames, flame phenomena in premixed combustible gases, and combustion of nonvolatile fuels are also discussed. This book consists of nine chapters and begins by introducing the reader to heats of reaction and formation, free energy and the equilibrium constants, and flame temperature calculations. The next chapter explores the rates of reactio

  13. Combustion

    CERN Document Server

    Glassman, Irvin

    2008-01-01

    Combustion Engineering, a topic generally taught at the upper undergraduate and graduate level in most mechanical engineering programs, and many chemical engineering programs, is the study of rapid energy and mass transfer usually through the common physical phenomena of flame oxidation. It covers the physics and chemistry of this process and the engineering applications-from the generation of power such as the internal combustion automobile engine to the gas turbine engine. Renewed concerns about energy efficiency and fuel costs, along with continued concerns over toxic and particulate emissions have kept the interest in this vital area of engineering high and brought about new developments in both fundamental knowledge of flame and combustion physics as well as new technologies for flame and fuel control. *New chapter on new combustion concepts and technologies, including discussion on nanotechnology as related to combustion, as well as microgravity combustion, microcombustion, and catalytic combustion-all ...

  14. Dew point of combustion products of coal from the Berezovo deposit

    Energy Technology Data Exchange (ETDEWEB)

    Petrov, V.A. (UralVTI (USSR))

    1990-11-01

    Evaluates properties of brown coal from the Berezovo deposit, Kansk-Achinsk basin, and properties of its combustion products. Coal properties are the following: sulfur content from 0.26 to 0.49%, ash content from 3.49 to 6.58%, moisture content from 31.6 to 36.9%, calorific value from 14,200 to 15,840 kJ/kg. Dew point of the combustion products amounts to 51 C and is equal to that of water vapor present in flue gases. Changing boiler output does not influence dew point. Increase in the excess air coefficient from 1.2 to 1.4 results in an increase in dew point by 2-3 K; further increase in air excess coefficient to 1.64 causes a decline in dew point by 3-4 K. 2 refs.

  15. Point de vue de la population sur la réforme du secteur de la ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Point de vue de la population sur la réforme du secteur de la sécurité palestinien. Dans le cadre de son plan visant à bâtir les institutions de l'État palestinien, le gouvernement de Salam Fayyad s'était engagé en août 2009 à moderniser le secteur de la sécurité palestinien en se fondant sur l'État de droit, sous la ...

  16. International Conference on Fixed Point Theory and Applications (Colloque International Theorie Du Point Fixe et Applications)

    Science.gov (United States)

    1989-06-09

    could be used to establish a conjectured minimax for a search game of Baston and Bostock [2]. An application of Theorem 1 is to the problem of getting...Alpern S., Search for point in interval, with high-low feedback, Math. Proc., Cambridge Phil. Soc. 98, (1985), 569-578. [2] Baston V. J. and Bostock F. A

  17. Combustion

    CERN Document Server

    Glassman, Irvin

    1997-01-01

    This Third Edition of Glassman's classic text clearly defines the role of chemistry, physics, and fluid mechanics as applied to the complex topic of combustion. Glassman's insightful introductory text emphasizes underlying physical and chemical principles, and encompasses engine technology, fire safety, materials synthesis, detonation phenomena, hydrocarbon fuel oxidation mechanisms, and environmental considerations. Combustion has been rewritten to integrate the text, figures, and appendixes, detailing available combustion codes, making it not only an excellent introductory text but also an important reference source for professionals in the field. Key Features * Explains complex combustion phenomena with physical insight rather than extensive mathematics * Clarifies postulates in the text using extensive computational results in figures * Lists modern combustion programs indicating usage and availability * Relates combustion concepts to practical applications.

  18. Acid dew point measurements in combustion gases using the dew point measuring system AH 85100

    Energy Technology Data Exchange (ETDEWEB)

    Fehler, D.

    1984-01-01

    Measuring system for continuous monitoring of the SO/sub 2//SO/sub 3/ dew point in the flue gas, characterized by a low failure rate, applicability inside the flue gas duct, maintenance-free continuous operation, and self-cleaning. The measuring principle is the cooling of the sensor element down to the 'onset condensation' message. Sensor surface temperatures are listed and evaluated as flue gas dew point temperatures. The measuring system is described. (DOMA).

  19. Accurate Anharmonic Zero-Point Energies for Some Combustion-Related Species from Diffusion Monte Carlo.

    Science.gov (United States)

    Harding, Lawrence B; Georgievskii, Yuri; Klippenstein, Stephen J

    2017-06-08

    Full-dimensional analytic potential energy surfaces based on CCSD(T)/cc-pVTZ calculations have been determined for 48 small combustion-related molecules. The analytic surfaces have been used in Diffusion Monte Carlo calculations of the anharmonic zero-point energies. The resulting anharmonicity corrections are compared to vibrational perturbation theory results based both on the same level of electronic structure theory and on lower-level electronic structure methods (B3LYP and MP2).

  20. Dew point measurements of flue gases in steam generators with brown coal combustion

    Energy Technology Data Exchange (ETDEWEB)

    Schinkel, W.

    1980-01-01

    This paper examines empirical data on sulfuric acid condensation and resulting internal corrosion in brown coal fired steam generators. Due to the high sulfur content in brown coal (0.5% to 5.0%) and relative short duration of the gases in the combustion chamber the concentrations of sulfur trioxide present in the flue gases can condense at the heat exchange surfaces of the steam generators. A number of diagrams show sulfuric acid dew point temperatures depending on brown coal sulfur content, the influence of combustion air supply on the dew point, and condensing speed and the rate of corrosion in relation to different heat exchange surface temperatures. The conclusion is made that a five-fold increase in corrosion can be caused by a 10 K higher flue gas dew point, a 5 K cooling of heating surfaces can also cause heavy corrosion at a certain dew point. Maximum corrosion results at 20 to 50 K differences between flue gas dew point and heat exchange surfaces. Optimum operation of steam generators with minimal internal corrosion requires the consideration of flue gas and heating surface temperatures as well as flue gas sulfur acid dew points. (10 refs.) (In German)

  1. The fuel element of the first charge for EL 4; presentation, main problems arising in the research, production problems; L'element combustible du 1. jeu de EL 4; presentation, problemes essentiels poses par l'etude, problemes de fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Ringot, C; Bailly, H; Bujas, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The fuel element making up the first charge for EL-4 is made of slightly enriched uranium oxide canned in stainless steel. This fuel element makes it possible to operate the reactor in the safest conditions awaiting the development of the fuel which will be finally adopted; this will have a low absorption can: beryllium, or a zirconium copper alloy. The 500 mm assembly is made up of 19 small rods placed on 3 rings, inside a graphite jacket. The solution adopted was a solution using completely independent small rods. This report deals with possible problems resulting from their study and production. (authors) [French] L'element combustible du 1er jeu EL-4 est un element combustible a oxyde d'uranium legerement enrichi gaine d'acier inoxydable. C'est un element combustible permettant de faire fonctionner le reacteur EL 4 dans des conditions aussi sures que possible avant de mettre au point le combustible definitif qui sera a gaine peu absorbante: beryllium, ou alliage zirconium-cuivre. L'assemblage de longueur 500 mm est constitue de 19 crayons places sur 3 couronnes, a l'interieur d'une chemise de graphite. La solution adoptee a ete une solution a crayons independants les uns des autres. Ce rapport traite des problemes eventuels poses par leur etude et leur fabrication. (auteurs)

  2. Burnup determination of power reactor fuel elements by gamma spectrometry; Determination par spectrometrie {gamma} du taux d'irradiation des elements combustibles des reacteurs de puissance

    Energy Technology Data Exchange (ETDEWEB)

    Robin, M; Jastrzeb, M; Boisliveau, S; Boyer, R; Vidal, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1969-07-01

    This report describes a method for determining by {gamma} spectrometry the burn up and the specific power of fuel elements irradiated in power reactors. The energy spectrum of {gamma} rays emitted by fission products is measured by means of a simple equipment using a sodium iodide detector and a multichannel analyzer. In order to extract from the spectrum a quantity proportional to the burn up, it is necessary to: - isolate an activity specific of one emitter,- give the same importance to fissions in uranium and plutonium - take into account the radioactive decay during and after irradiation. One hundred fuel elements were studied and burn up values obtained by {gamma} spectrometry are compared to results given by chemical analyses. Preliminary measurements show that the accuracy of the results is greatly increased by the use of a germanium detector, due to its good resolution. (authors) [French] Ce rapport expose une methode de determination par spectrometrie {gamma} du taux d'irradiation et de la puissance specifique des elements combustibles irradies dans les reacteurs de puissance. Une installation simple utilisant un detecteur d'iodure de sodium et un selecteur multicanaux mesure le spectre en energie du rayonnement {gamma} emis par les produits de fission. Afin d'extraire du spectre une quantite proportionnelle au taux de combustion, il faut: - isoler une activite specifique a un emetteur, - donner la meme importance aux fissions survenues dans l'uranium et le plutonium, - prendre en compte la decroissance radioactive pendant et apres l'irradiation. Les mesures ont porte sur une centaine d'elements combustibles et les taux de combustion obtenus par spectrometrie {gamma} sont compares aux resultats des analyses chimiques. Des mesures preliminaires montrent que l'utilisation d'un detecteur de germanium augmente considerablement la precision des resultats, en raison de son excellente resolution. (auteurs)

  3. Mise au point de la protection intégrée du colza : exemple du phoma (Leptosphaeria maculans

    Directory of Open Access Journals (Sweden)

    Aubertot Jean-Noël

    2003-05-01

    Full Text Available En France, le phoma est considéré comme la maladie la plus préoccupante du colza. Il n’existe aucune méthode de lutte à la fois efficace, rentable et respectueuse de l’environnement. Il apparaît donc nécessaire de développer la lutte intégrée de la culture contre cette maladie. Cette communication présente les résultats d’un programme de recherche visant à analyser et à modéliser les effets des systèmes de culture sur le développement de la maladie. Des pistes concrètes pour la mise en oeuvre de la lutte intégrée contre le phoma sont proposées.

  4. Dew point of flue gas in the combustion of brown coal briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Schinkel, W

    1977-08-01

    Economical operation of small steam generators can follow two courses, viz. to channel the emitted gases through the plant and reduce waste gas loss. Two possibilities exist to achieve this: firstly a steam generating process with only slight excess air; secondly a reduction of the emitted gas temperature. The lowest waste gas temperature found in sulphur-containing combustion materials is measured by finding the acid dew-point of the waste gas. The following results in the case of brown coal briquettes were found. Measurements of the dew point of flue gas in two steam generators, both of the double flue type, one having a capacity of 12.5 t/h, the other 25 t/h, one using brown coal briquettes with 1% sulphur content, the other with 3%, resulted in the fact that the dew point can be measured. It was shown that a low air ratio leads to a lowering of the dew point. However this process is unfortunately economically unviable in chain grate generators as the waste gas becomes so thin under a high air ratio that the dew point can only be minimally reduced. Further the acid dew point is only slightly influenced by partial operation of the generator and the infusion of briquette residue.

  5. A Comparison of Combustion Dynamics for Multiple 7-Point Lean Direct Injection Combustor Configurations

    Science.gov (United States)

    Tacina, K. M.; Hicks, Y. R.

    2017-01-01

    The combustion dynamics of multiple 7-point lean direct injection (LDI) combustor configurations are compared. LDI is a fuel-lean combustor concept for aero gas turbine engines in which multiple small fuel-air mixers replace one traditionally-sized fuel-air mixer. This 7-point LDI configuration has a circular cross section, with a center (pilot) fuel-air mixer surrounded by six outer (main) fuel-air mixers. Each fuel-air mixer consists of an axial air swirler followed by a converging-diverging venturi. A simplex fuel injector is inserted through the center of the air swirler, with the fuel injector tip located near the venturi throat. All 7 fuel-air mixers are identical except for the swirler blade angle, which varies with the configuration. Testing was done in a 5-atm flame tube with inlet air temperatures from 600 to 800 F and equivalence ratios from 0.4 to 0.7. Combustion dynamics were measured using a cooled PCB pressure transducer flush-mounted in the wall of the combustor test section.

  6. Fuel location, homogeneity and amount in flat and tubular configurations; Repartition, Homogeneite et Quantite du Combustible dans les Elements a Configuration Plate ou Tubulaire; Polozhenie, gomogennost' i kolichestvo topliva v ploskikh i trubchatykh konfiguratsiyakh; Disposicion, Homogeneidad y Cantidad de Combustibles en Configuraciones Planas y Tubulares

    Energy Technology Data Exchange (ETDEWEB)

    Meester, P. de [Studiecentrum voor Kernenergie, Mol (Belgium)

    1965-10-15

    standards are considered. Accuracy and elimination of errors are discussed. Some possible future improvements in the tests are proposed. (author) [French] Les elements combustibles pour le reacteur d'essai de materiaux BR-2 peuvent etre-realises, soit avec des plaques obtenues par cadrages, soit avec des tubes obtenus par coextrusion. Au cours de la fabrication et avant le chargement dans le reacteur, il faut verifier ou mesurer la repartition, l'homogeneite et la quantite du combustible. Il faut connaitre la repartition du combustible pour le positionnement de l'ame dans les plaques et tubes ainsi que pour une premiere evaluation qualitative du produit du point de vue des specifications geometriques. On a procede a des radiographies 3 80-90 keV, ainsi qu'a des autoradiographies et gammagraphies avec une source au thulium-170. Pour l'examen radiographique des tubes de combustible, on a introduit dans le tube un mandrin en plomb auquel etait fixe un film sensible aux rayons X , puis on a fait des radiographies sous divers angles. En utilisant une source radioactive se deplacant le long de l'axe du tube et un film place autour du tube, on a obtenu des enregistrements avec un tres bon contraste. Il faut controler l'homogeneite du combustible pour assurer la securite du fonctionnement du reacteur, c'est-a-dire pour eviter toute concentration excessive de combustible pouvant donner lieu a des formations de vapeur pendant le fonctionnement du reacteur et pour garantir que le chargement de combustible est suffisant et regulierement reparti. On peut faire appel a des radiographies en vue d'une verification visuelle. Cependant, s'il est necessaire de faire une analyse quantitative, il est preferable d'utiliser un spectrometre g a m m a a scintillation permettant de mesurer le rayonnement propre emis par l'uranium-235. Le memoire contient une' analyse des resultats obtenus pour quelque 400 plaques de combustible et pour un premier lot de tubes de combustible. Il est possible de

  7. Combustion Dynamic Characteristics Identification in a 9-point LDI Combustor Under Choked Outlet Boundary Conditions

    Science.gov (United States)

    He, Zhuohui J.; Chang, Clarence T.

    2017-01-01

    Combustion dynamics data were collected at the NASA Glenn Research Center's CE-5 flame tube test facility under combustor outlet choked conditions. Two 9-point Swirl-Venturi Lean Direct Injection (SV-LDI) configurations were tested in a rectangular cuboid combustor geometry. Combustion dynamic data were measured at different engine operational conditions up to inlet air pressure and temperature of 24.13 bar and 828 K, respectively. In this study, the effects of acoustic cavity resonance, precessing vortex core (PVC), and non-uniform thermal expansion on the dynamic noise spectrum are identified by comparing the dynamic data that collected at various combustor inlet conditions along with combustor geometric calculations. The results show that the acoustic cavity resonance noises were seen in the counter-rotating pilot configuration but not in the co-rotating pilot configuration. Dynamic pressure noise band at around 0.9 kHz was only detected at the P'41 location (9.8 cm after fuel injector face) but not at the P'42 location (29 cm after the fuel injector face); the amplitude of this noise band depended on the thermal expansion ratio (T4/T3). The noise band at around 1.8 kHz was found to depend on the inlet air pressure or the air density inside the combustor. The PVC frequency was not observed in these two configurations.

  8. The reprocessing of irradiated fuels improvement and extension of the solvent extraction process; Le traitement des combustibles irradies amelioration et extension du procede utilisant les solvants

    Energy Technology Data Exchange (ETDEWEB)

    Faugeras, P; Chesne, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-07-01

    Improvements made in the conventional tri-butylphosphate process are described, in particular. the concentration and the purification of plutonium by one extraction cycle using tri-butyl-phosphate with reflux; and the use of an apparatus working continuously for precipitating plutonium oxalate, for calcining the oxalate, and for fluorinating the oxide. The modifications proposed for the treatment of irradiated uranium - molybdenum alloys are described, in particular, the dissolution of the fuel, and the concentration of the fission product solutions. The solvent extraction treatment is used also for the plutonium fuels utilized for the fast breeder reactor (Rapsodie) An outline of the process is presented and discussed, as well as the first experimental results and the plans for a pilot plant having a capacity of 1 kg/day. The possible use of tn-lauryl-amine in the plutonium purification cycle is now under consideration for the processing plant at La Hague. The flowsheet for this process and its performance are presented. The possibility of vitrification is considered for the final treatment of the concentrated radioactive wastes from the Marcoule (irradiated uranium) and La Hague (irradiated uranium-molybdenum) Centers. Three possible processes are described and discussed, as well as the results obtained from the operation of the corresponding experimental units using tracers. (authors) [French] On decrit les ameliorations apportees au procede classique utilisant le phosphate tributylique, et notamment la concentration et la purification du plutonium par un cycle d'extraction au tributylphosphate avec reflux, l'utilisation d'un appareillage continu de precipitation d'oxalate de plutonium, de calcination de l'oxalate, et de fluoration de l'oxyde. On presente les modifications envisagees pour le traitement des alliages uranium-molybdene irradies, principalement en ce qui concerne la dissolution du combustible et la concentration des solutions de produits de fission

  9. Accurate prediction of the dew points of acidic combustion gases by using an artificial neural network model

    International Nuclear Information System (INIS)

    ZareNezhad, Bahman; Aminian, Ali

    2011-01-01

    This paper presents a new approach based on using an artificial neural network (ANN) model for predicting the acid dew points of the combustion gases in process and power plants. The most important acidic combustion gases namely, SO 3 , SO 2 , NO 2 , HCl and HBr are considered in this investigation. Proposed Network is trained using the Levenberg-Marquardt back propagation algorithm and the hyperbolic tangent sigmoid activation function is applied to calculate the output values of the neurons of the hidden layer. According to the network's training, validation and testing results, a three layer neural network with nine neurons in the hidden layer is selected as the best architecture for accurate prediction of the acidic combustion gases dew points over wide ranges of acid and moisture concentrations. The proposed neural network model can have significant application in predicting the condensation temperatures of different acid gases to mitigate the corrosion problems in stacks, pollution control devices and energy recovery systems.

  10. Le point sur les indices du bien-être national | CRDI - Centre de ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    21 janv. 2011 ... Les indices économiques sont des outils statistiques qui résument des ... En quelques mots, le PIB correspond à la valeur totale des biens et ... copieux menu d'instruments de mesure allant du réjouissant Happy Planet Index, ...

  11. Determining a pool - type reactor fuel policy; Recherche d'une politique de gestion du combustible d'une pile piscine

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1964-07-01

    Refuelling the 10 to 15 MW pool type reactor considered here will occur frequently (some 10 elements every 3 to 4 weeks). It is therefore necessary to determine the most economic fuel policy. This study proposes to define a strategy that will make it possible to decide on the number and characteristics of the shipment containers, as well as on the means of storage, so as to reduce the risks as much as possible should the basic parameters of the study vary. Among these parameters, the respective influence of which is investigated, chemical reprocessing costs play a vital part. Two examples of optimum fuel management are given according to whether the reprocessing charges applied are those of the old or of the 1961 U.S. AEC base charges for reprocessing highly enriched irradiated fuel. (authors) [French] Les renouvellements du combustible de la pile piscine de 10 a 15 MW consideree ici, seront frequents (quelques 10 elements toutes les 3 ou 4 semaines). Il est donc important de connaitre les meilleures conditions de gestion economique de ce combustible. Cette etude se propose de definir une strategie permettant de choisir le nombre et les caracteristiques des containers de transport, ainsi que les moyens de stockage, de facon a minimiser les risques si les parametres de base de l'etude varient. Parmi ces parametres dont l'influence respective est successivement examinee, le cout du traitement chimique joue un role fondamental. Deux exemples d'optimum de gestion sont donnes selon que le tarif de retraitement est conforme a l'ancien tarif de l'U.S. AEC ou au tarif 1961 de traitement des combustibles irradies tres enrichis. (auteurs)

  12. Processing Th C{sub 2} - UC{sub 2} fuel extracted from high temperature reactors HTGCR; Etude du traitement des combustibles Th C{sub 2} - UC{sub 2} issus de reacteurs a haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Derrien, C; Lessart, P; Pianezza, E; Verry, C; Villain, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-07-01

    The object of this investigation is solubilisation head-end (from crushing and grinding phase to non included first purification phase) of pulverulent ({sup 233}U/{sup 232}Th)C{sub 2} (200 - 500 microns diameter) contained in a graphite matrix extracted from a 4.10{sup 13} n.cm{sup -2}.s{sup -1} thermalized neutrons average flux with an irradiation of 80000 MWjT{sup -1} HTGCR reactor. After having succinctly described different bibliographic processes we have chosen the burn - leach of reactor fuel and graphite matrix containing it. The technology of burner is original in nuclear field and still more by utilizing ultra-sounds to intensify burning reaction and to minimize the weight of unburnables. The mixture of ThO{sub 2}, U{sub 3}O{sub 8}, and fission products oxides is solubilized by boiling HNO{sub 3} 13 M + HF 0.05 M. This process is profit-learning in a thorium recuperation and reprocessing point of view. In the contrary-case it would be interesting to consider a dry-process which would permit to separate solid ThF{sub 4} from gaseous UF{sub 6}. (authors) [French] Cette etude a pour objet le traitement initial de mise en solution ou 'head-end' (allant de la phase broyag-concassage a la phase de premiere purification exclue) d'un combustible ({sup 233}U/{sup 232}Th)C{sub 2} pulverulent (de 200 a 500 {mu} de diametre) contenu dans une matrice de graphite issu d'un reacteur HTGCR surgenerateur a neutrons thermiques de flux moyen 4. l0{sup 13} n.cm{sup -2}.s{sup -1} et taux d'irradiation 80000 MWjT{sup -1}. Apres exposition succincte des differents procedes bibliographiques decrits, nous avons finalement choisi le traitement par combustion-attaque ('Burn-Leach') du combustible et de la matrice etanche graphite qui le contient. La technologie du bruleur est originale dans le domaine nucleaire d'autant qu'elle utilise les ultra-sons pour ameliorer le rendement de la reaction de combustion et reduire au minimum le poids des imbrules. Le melange ThO{sub 2}, U{sub 3}O

  13. Vérification du point de vue des droits de la personne et de la paix ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Le CRDI lance un nouveau projet dans la région de l'ANASE. L'honorable Chrystia Freeland, ministre du Commerce international, a annoncé le lancement d'un nouveau projet financé par le Centre de recherches pour le développement international (CRDI). Voir davantageLe CRDI lance un nouveau projet dans la région ...

  14. Migration et sexospécificités : le point de vue du mouvement ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Les mouvements de femmes en Inde ont du mal à résoudre les problèmes suscités par les changements rapides au chapitre des relations sociales et les vulnérabilités reliées, entre autres, au phénomène de la migration. Ce projet permettra à une équipe pluridisciplinaire composée d'économistes, d'historiens, de ...

  15. Non-Destructive Methods for Determining Burn-Up in Nuclear Fuel; Methodes Non Destructives d'Evaluation du Taux de Combustion dans le Combustible Nucleaire; Metody opredeleniya vygoraniya v yadernom toplive bez razrusheniya obraztsa; Metodos No Destructivos para Determinai el Grado de Combustion de los Elementos Combustibles Nucleares

    Energy Technology Data Exchange (ETDEWEB)

    McGonnagle, W. J. [Illinois Institute of Technology, Chicago, IL (United States)

    1966-02-15

    is of secondary importance and the cooling time is unimportant. Also, there is more precise nuclear data for the stable fission products. Of the stable isotopes produced during the fission process, zirconium, molybdenum, ruthenium, and neodymium appear to be the most useful. The proposed non-destructive methods using stable isotopes will be discussed. (author) [French] Il est a la fois utile et souhaitable d'utiliser des methodes non destructives pour proceder a la mesure quantitative du taux de combustion des elements combustibles d'un reacteur nucleaire. L'ideal serait de pouvoir analyser le combustible a l'aide d'une methode ne necessitant pas de renseignements particuliers sur les spectres des neutrons, le schema d'irradiation ou le temps de refroidissement. Les isotopes radioactifs et les isotopes stables resultant du processus de fission qui sont presents dans un element combustible irradie caracterisent son irradiation. Malheureusement, que l'analyse soit effectuee au moyen de methodes destructives ou non destructives, les resultats obtenus varient en fonction du spectre de neutrons, du schema d'irradiation et du temps de refroidissement. Deplus, l'absence de donnees nucleaires precises, comme les valeurs des section efficaces, influe sur tous les calculs qui peuvent etre effectues. L'analyse non destructive est egalement genee par la presence de champs de rayonnements intenses qui augmentent le bruit de fond. Il est difficile d'etablir des normes utiles et realistes. Bien que, dans l'etat actuel de la technique, les methodes non destructives n'aient pas toute la precision et l'exactitude voulues, elles presentent neanmoins un grand interet' notamment dans les cas ou il faut obtenir rapidement et economiquement une valeur approximative du taux de combustion. Plusieurs methodes non destructives d'evaluation du taux de combustion sont actuellement appliquees, a l'etude ou en projet. Plusieurs types de spectrometres sont utilises pour la mesure du rayonnement

  16. Mixture preparation and combustion in an optically-accessible HCCI, diesel engine; La preparation du melange et de la combustion dans un moteur Diesel, HCCI a acces optique

    Energy Technology Data Exchange (ETDEWEB)

    Kashdan, J.; Bruneaux, G. [Institut Francais du Petrole, 92 - Rueil-Malmaison (France)

    2006-07-01

    Planar laser-induced fluorescence (LIF) imaging techniques have been applied in order to study the mixture preparation and combustion process in a single cylinder, optically-accessible homogeneous charge, compression ignition (HCCI) engine. In particular, the influence of piston bowl geometry on the in-cylinder mixture distribution and subsequent combustion process has been investigated. A new optically-accessible piston design enabled the application of LIF diagnostics directly within the combustion chamber bowl. Firstly, laser-induced exciplex fluorescence (LIEF) was exploited in order to characterise the in-cylinder fuel spray and vapour distribution. Subsequently a detailed study of the two-stage HCCI combustion process was conducted by a combination of direct chemiluminescence imaging, laser-induced fluorescence (LIF) of the intermediate species formaldehyde (CH{sub 2}O) which is present during the cool flame and LIF of the OH radical which is subsequently present in the reaction and burned gas zones at higher temperature. Finally, spectrometry measurements were performed with the objective of determining the origin of the emitting species of the chemiluminescence signal. The experiments were performed on a single cylinder optical engine equipped with a direct-injection, common rail injection system and narrow angle injector. The experimental results presented reveal the significant role of the combustion chamber geometry on the mixture preparation and combustion characteristics for late HCCI injection strategies particularly in such cases where liquid impingement is unavoidable. Planar LIF 355 imaging revealed the presence of the intermediate species formaldehyde allowing the temporal and spatial detection of auto-ignition precursors prior to the signal observed by chemiluminescence in the early stages of the cool flame. Formaldehyde was then rapidly consumed at the start of main combustion which was marked not only by the increase in the main heat release

  17. Dosage of fission products in irradiated fuel treatment effluents (radio-chemical method); Dosage des produits de fission dans les effluents du traitement des combustibles irradies (methode radiochimique)

    Energy Technology Data Exchange (ETDEWEB)

    Auchapt, J [Commissariat a l' Energie Atomique, Marcoule (France). Centre d' Etudes Nucleaires

    1966-07-01

    The dosage methods presented here are applicable to relatively long-lived fission products present in the effluents resulting from irradiated fuel treatment processes (Sr - Cs - Ce - Zr - Nb - Ru - I). The methods are based on the same principle: - addition of a carrying-over agent - chemical separation over several purification stages, - determination of the chemical yield by calorimetry - counting of an aliquot liquid portion. (author) [French] Les methodes de dosage presentees concernent les produits de fission a vie relativement longue presents dans les effluents de traitement des combustibles irradies (Sr - Cs - Ce - Zr - Nb - Ru - I). Elles sont toutes basees sur le meme principe: - addition d'entraineur, - separation chimique en plusieurs stades de purification, - determination du rendement chimique par calorimetrie, - comptage d'une aliquote liquide. (auteur)

  18. Simulation Investigation on Combustion Characteristics in a Four-Point Lean Direct Injection Combustor with Hydrogen/Air

    Directory of Open Access Journals (Sweden)

    Jianzhong Li

    2017-06-01

    Full Text Available To investigate the combustion characteristics in multi-point lean direct injection (LDI combustors with hydrogen/air, two swirl–venturi 2 × 2 array four-point LDI combustors were designed. The four-point LDI combustor consists of injector assembly, swirl–venturi array and combustion chamber. The injector, swirler and venturi together govern the rapid mixing of hydrogen and air to form the mixture for combustion. Using clockwise swirlers and anticlockwise swirlers, the co-swirling and count-swirling swirler arrays LDI combustors were achieved. Using Reynolds-Averaged Navier–Stokes (RANS code for steady-state reacting flow computations, the four-point LDI combustors with hydrogen/air were simulated with an 11 species and 23 lumped reaction steps H2/Air reaction mechanism. The axial velocity, turbulence kinetic energy, total pressure drop coefficient, outlet temperature, mass fraction of OH and emission of pollutant NO of four-point LDI combustors, with different equivalence ratios, are here presented and discussed. As the equivalence ratios increased, the total pressure drop coefficient became higher because of increasing heat loss. Increasing equivalence ratios also corresponded with the rise in outlet temperature of the four-point LDI combustors, as well as an increase in the emission index of NO EINO in the four-point LDI combustors. Along the axial distance, the EINO always increased and was at maximum at the exit of the dump. Along the chamber, the EINO gradually increased, maximizing at the exit of chamber. The total temperature of four-point LDI combustors with different equivalence ratios was identical to the theoretical equilibrium temperature. The EINO was an exponential function of the equivalence ratio.

  19. Natural gas combustion and indoor air quality in domestic premises; Combustion du gaz naturel et qualite de l'air a l'interieur des habitations

    Energy Technology Data Exchange (ETDEWEB)

    Occhio, L.; Riva, A. [Snam, (Italy); Canci, F.; Scevarolli, V. [Italgas, Torino (Italy)

    2000-07-01

    Indoor air quality depends on many factors; combustion appliances are one of the sources of emissions inside dwellings. Their installation is regulated by UNI-CIG standards which also establish the ventilation and aeration requirements needed to guarantee the safety and healthiness of the environment. In order to critically evaluate the effect on indoor air quality of using gas appliances under different operational regimes and in different types of building, Snam and Italgas have developed a research project in co-operation with Enitecnologie and Turin Polytechnic, even to provide theoretical and experimental support for standardisation activities. The results of the presented research include experimental measurements made in real buildings, mathematical modelling and analysis of Italian and international literature. The results show that use of combustion appliances has little influence on indoor air quality and does not affect people's health. (authors)

  20. Experimental and numerical study of the active control of jets inside combustion chambers; Etude experimentale et numerique du controle actif de jets dans des chambres de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Faivre, V

    2003-12-15

    Combustion instabilities occur when the flame heat release couples with the acoustic waves propagating in the combustion chamber. This phenomenon can lead to strong vibrations and noise but also, sometimes, to the complete combustion device failure. That is the reason why so many studies focus on the control of those instabilities. The method chosen in this study consists in an active control device (or set of actuators) having a strong effect on the mixing of the burner exhaust flow with the ambient fluid. The model configuration studied consists in a non reactive jet of air controlled by four small tangential secondary jets. Experiments have been carried out to optimize the control device geometry. The configuration identified as the most efficient, in terms of mixing enhancement, has been simulated through Large Eddy Simulations (LES). The objective of the numerical part of the present work is double. First, the numerical simulations provide a better understanding of the phenomena occurring when the control is on. Then, it is shown that LES can be considered as a tool to predict the effects of a control device on a flow. (author)

  1. Nouveaux critères pour juger de l'efficacité d'un fourneau à la combustion du charbon de bois

    Directory of Open Access Journals (Sweden)

    Ndaysenga, M.

    1994-01-01

    Full Text Available New Criteria to Judge Stove Efficiency in the Charcoal Combustion. The water boil test efficiency for choosing the most economic stove in combustion is estimated on the basis of four stoves. In addition to the heating and boiling energy usually considered as selection criterion, other criteria such as the boiling time and the combustion rate have been taken to indicate efficiency. Strangely, it appeared that the stove which maintains water at its boiling point for a long time and has the lowest combustion rate doesn 't valorize fuel energy efficiently if you only keep to the heating and boiling energy. The cooking test made it possible to explain that apparent contradiction : the fuel energy fraction which doesn't enter in the calculation of the heating and boiling energy isn't really lost. A low combustion rate associated with a long boiling time proved to be the best criteria of choosing the most economic stove in fuel. Therefore, the only water boil test doesn't make it possible to identify the most economically efficient stove. Resorting to the cooking test is compelling.

  2. Application de l'A.D.L, pour la mesure du champ de vitesses instationnaires de llecoulement a Ilechappement d'un moteur a combustion interne

    Science.gov (United States)

    Boutrif, M. S.; Thelliez, M.

    1993-01-01

    We present experimental results of instantaneous velocity measurement, which were obtained by application of the laser Doppler anemometry (L.D.A.) at the exhaust pipe of a reciprocating engine under real working conditions. First of all, we show that the instantaneous velocity is monodimensional along a straight exhaust pipe, and that the boundary layer develops within a 2mm thickness. We also show that the cylinder discharges in two phases : the blow down period and the final part of exhaust stroke. We also make obvious, that the flow escapes very quickly : its velocity varies between - 100m/s and 200m/s within a period shorter than 1ms ; thereby, we do record the acoustic resonance phenomenon, when the engine speed is greater than 3 000rpm. Finally, we show that in the exhaust pipe the apparent fluctuation - i.e. the cyclic dispersion and the actual turbulence - may reach 15%. Nous présentons des résultats expérimentaux du champ de vitesses instationnaires, obtenus par adaptation et application de la vélocimétrie laser interférentielle communément appelée à effet Doppler (L.D.A.), à l'échappement d'un moteur altematif à combustion inteme en fonctionnement nominal. Tout d'abord, nous montrons que dans un tube d'échappement long et droit, la vitesse instantanée est bien monodimensionnelle et que l'écoulement occupe la quasitotalité de la section droite géométrique du tube (une couche limite d'épaisseur inférieure à 2mm se développe très près de la paroi du tube). Nous pouvons également décrire la vidange du cylindre du moteur étudié en deux phases principales : bouffée d'échappement et refoulement des gaz brûlés par le piston. Nous mettons de même en évidence l'état très pulsé de l'écoulement, puisqu'en un intervalle de temps inférieur à 1ms, la vitesse de l'écoulement varie de - 100m/s à 200m/s ; nous enregistrons ainsi l'apparition du phénomène de résonance acoustique à des vitesses de rotation supérieures à 3 500

  3. Pratiques de publicité au point de vente dans l'industrie du tabac ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Des études menées dans des pays comme le Canada démontrent que la publicité au point de vente exerce une influence importante sur les écoliers et peut les prédisposer à devenir fumeurs. De plus, les ... Articles de revue. Tobacco point-of-sale advertising in Guatemala city, Guatemala and Buenos Aires, Argentina.

  4. Thermodynamic modeling of LPG combustion in dual-fuel engines; Modelisation thermodynamique de la combustion du GPL dans les moteurs dual-fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bilcan, A.; Le Corre, O.; Tazerout, M. [Ecole des Mines de Nantes, 44 (France); Ramesh, A. [Indian Institute of Technology Madras (India)

    2002-07-01

    Dual-fuel engines are modified diesel engines burning simultaneously two fuels inside the cylinder: a gaseous one, called the primary fuel and a liquid one, called the pilot fuel. The thermal efficiency of the dual-fuel engine and of the diesel engine are comparable; the level of emissions is lower compared to the diesel one. This article presents a new procedure for the combustion modeling in a LPG-diesel dual-fuel engine. The procedures deals with the ignition delay period and with the rate of heat release inside the cylinder. This procedure is validated using experimental data issued front a collaboration with the Indian Institute of Technology from Madras, India. The used engine is a single-cylinder one, air-cooled. The pilot fuel is direct injected inside the cylinder The engine was run at constant load and with different diesel substitutions, i.e. for different air to fuel ratios of the primary fuel-air mixture. The general error of the procedure is below 10%. (authors)

  5. Multi-point laser spark generation for internal combustion engines using a spatial light modulator

    International Nuclear Information System (INIS)

    Lyon, Elliott; Kuang, Zheng; Dearden, Geoff; Cheng, Hua; Page, Vincent; Shenton, Tom

    2014-01-01

    This paper reports on a technique demonstrating for the first time successful multi-point laser-induced spark generation, which is variable in three dimensions and derived from a single laser beam. Previous work on laser ignition of internal combustion engines found that simultaneously igniting in more than one location resulted in more stable and faster combustion – a key potential advantage over conventional spark ignition. However, previous approaches could only generate secondary foci at fixed locations. The work reported here is an experimental technique for multi-point laser ignition, in which several sparks with arbitrary spatial location in three dimensions are created by variable diffraction of a pulsed single laser beam source and transmission through an optical plug. The diffractive multi-beam arrays and patterns are generated using a spatial light modulator on which computer generated holograms are displayed. A gratings and lenses algorithm is used to accurately modulate the phase of the input laser beam and create multi-beam output. The underpinning theory, experimental arrangement and results obtained are presented and discussed. (paper)

  6. Large eddy simulation of premixed and non-premixed combustion in a Stagnation Point Reverse Flow combustor

    Science.gov (United States)

    Undapalli, Satish

    A new combustor referred to as Stagnation Point Reverse Flow (SPRF) combustor has been developed at Georgia Tech to meet the increasingly stringent emission regulations. The combustor incorporates a novel design to meet the conflicting requirements of low pollution and high stability in both premixed and non-premixed modes. The objective of this thesis work is to perform Large Eddy Simulations (LES) on this lab-scale combustor and elucidate the underlying physics that has resulted in its excellent performance. To achieve this, numerical simulations have been performed in both the premixed and non-premixed combustion modes, and velocity field, species field, entrainment characteristics, flame structure, emissions, and mixing characteristics have been analyzed. Simulations have been carried out first for a non-reactive case to resolve relevant fluid mechanics without heat release by the computational grid. The computed mean and RMS quantities in the non-reacting case compared well with the experimental data. Next, the simulations were extended for the premixed reactive case by employing different sub-grid scale combustion chemistry closures: Eddy Break Up (EBU), Artificially Thickened Flame (TF) and Linear Eddy Mixing (LEM) models. Results from the EBU and TF models exhibit reasonable agreement with the experimental velocity field. However, the computed thermal and species fields have noticeable discrepancies. Only LEM with LES (LEMLES), which is an advanced scalar approach, has been able to accurately predict both the velocity and species fields. Scalar mixing plays an important role in combustion, and this is solved directly at the sub-grid scales in LEM. As a result, LEM accurately predicts the scalar fields. Due to the two way coupling between the super-grid and sub-grid quantities, the velocity predictions also compare very well with the experiments. In other approaches, the sub-grid effects have been either modeled using conventional approaches (EBU) or need

  7. Assessment of whether upstream passage for Lake Sturgeon is needed at the Pointe du Bois Generating Station (Winnipeg River)

    International Nuclear Information System (INIS)

    Pratt, T.

    2010-01-01

    This document reviewed Manitoba Hydro's proposal to modernize the Pointe du Bois Generating Station (GS) on the Winnipeg River, with particular reference to the potential impacts on Lake Sturgeon in Management Unit 5 (MU5) where large numbers of the fish spawn at the base of the falls. The modernization will involve replacing the spillway, dam segments and replacing or repairing the powerhouse. The pros and cons of providing upstream fish passage for Lake Sturgeon and the generating station were outlined. The only spawning area in the MU5 area may be altered considerably due to changes in water flow, depending on the design chosen for modernization. A potential benefit of providing upstream fish passage for Lake Sturgeon would be to increase genetic diversity within the Winnipeg River. Another potential benefit would be to allow Lake Sturgeon, from the relatively dense population below the GS, to move upstream into MU4 where unfilled habitat may be available and Lake Sturgeon abundance is lower. A potential disadvantage of providing fish passage would be the loss of individual Lake Sturgeon from the healthy population in MU5 with no accompanying benefit to MU4. There would be no net gain to MU4 or MU5 if migrating Lake Sturgeon returned to MU5 rather than proceeding upstream. It was concluded that these current gaps in knowledge must be filled in order to fully assess the environmental impacts. 2 figs.

  8. Geophysical investigation of the June 6, 1944 D-Day invasion site at Pointe du Hoc, Normandy, France

    Science.gov (United States)

    Everett, M. E.; Pierce, C. J.; Warden, R. R.; Burt, R. A.

    2005-05-01

    A near-surface geophysical survey at the D-Day invasion site atop the cliffs at Pointe du Hoc, Normandy, France was carried out using ground-penetrating radar, electromagnetic induction, and magnetic gradiometry equipment. The subsurface targets of investigation are predominantly buried concrete and steel structures and earthworks associated with the German coastal fortifications at this stronpoint of Hitler's Atlantic Wall. The targets are readily detectable embedded within the vadose zone of a weakly magnetic, electrically resistive loess soil cover. The radar and electromagnetic induction responses lend themselves to plan-view imaging of the subsurface, while the magnetics data reveal the presence of buried magnetic bodies in a more subtle fashion. Several intriguing geophysical signatures were discovered, including what may be the buried remains of a railway turntable, ordnance fragments in the bomb craters, a buried steel-reinforced concrete trench, and a linear chain of machine gun firing positins. Geophysical prospecting is shown to be a very powerful tool for historical battlefield characterization.

  9. Cliff stability assessment using electrical resistivity tomography at the historic WWII D-Day invasion site, Pointe du Hoc, France

    Science.gov (United States)

    Everett, M. E.; Udphuay, S.; Warden, R.

    2007-05-01

    The 1944 D-Day invasion site at Pointe du Hoc, Normandy, France is an important WWII battlefield and cultural resource but is at risk from chalk cliff collapse. The American Battle Monuments Commission tasked us to evaluate the geohazard to the observation post and other cliff-side buildings of historical significance. Geophysical multi-electrode resistivity profiling is used to study cliff stability and the condition of the observation- post foundations. Preliminary 2-D geological interpretations are provided of individual profiles. The copious steel, concrete and void spaces at the site renders hydrogeological interpretation challenging but tractable. The cliff face appears to be relatively intact and well-drained. Several routes taken by groundwater into fractures within the chalk were identified mainly on the western side of the site. The eastern side is drier and somewhat sheltered from the Atlantic storms but may contain large void spaces that could efficiently transmit groundwater flow during heavy precipitation events, thereby imperiling the major antiaircraft gun emplacement occupied by Col. Rudder in the early days of the Allied invasion. The forward German observation post perched close to the sea stack, which now hosts the U.S. Ranger memorial, may be moving with the soil and not securely anchored to bedrock. A complex failure mechanism is identified as a combination of groundwater dissolution of the fractured chalk and sea wave attack at the cliff base.

  10. M. G.-F. Leclerc, Préfet de la Haute-Savoie lors de sa visite dans le tunnel du LHC au Point 2 avec D. Delikaris, Département Technologie; dans la caverne de l'expérience ALICE avec B. Erazmus, Collaboration ALICE et lors de la signature du livre d'or avec F. Bordry, Chef du Département Technologie. P. Fassnacht, Conseiller au Bureau des Relations internationales présent.

    CERN Multimedia

    Jean-Claude Gadmer

    2013-01-01

    M. G.-F. Leclerc, Préfet de la Haute-Savoie lors de sa visite dans le tunnel du LHC au Point 2 avec D. Delikaris, Département Technologie; dans la caverne de l'expérience ALICE avec B. Erazmus, Collaboration ALICE et lors de la signature du livre d'or avec F. Bordry, Chef du Département Technologie. P. Fassnacht, Conseiller au Bureau des Relations internationales présent.

  11. Un point de vue néoréaliste en épistémologie du journalisme

    Directory of Open Access Journals (Sweden)

    Gilles Gauthier

    2017-01-01

    Full Text Available Il peut y avoir un certain intérêt à traiter de la nature du journalisme non pas pour en circonscrire les limites, mais afin de mettre au jour les présuppositions qui président à sa pratique. C’est une proposition en ce sens qui est ici formulée. Le point de vue épistémologique qui est développé dans le texte est librement inspiré du réalisme naturaliste de John Searle et du « nouveau réalisme » de Maurizio Ferraris et Markus Gabriel. Il se décline en trois principes : un principe de réalité, un principe de vérité et un principe d’objectivité. Tels qu’ils sont ici caractérisés, ces trois principes sont ordonnés séquentiellement : du principe de réalité découle le principe de vérité duquel est dérivé le principe d’objectivité. Le principe de réalité pose que le journalisme porte sur un matériau préexistant qui lui donc indépendant : des faits existent que le journalisme prend pour objet. Ces faits sont pour la plupart ceux de la réalité sociale. Ils sont construits, mais pas par le journalisme. Suivant le principe de vérité, le journalisme fournit de la réalité dont il traite une représentation exacte. Il ne s’agit pas, en le reconnaissant, de défendre une thèse positiviste qui soutiendrait qu’il y a isomorphisme entre la réalité représentée et la représentation qu’en fournit le journalisme, mais de marquer que la visée du journalisme est de rendre compte de ce qui est effectivement le cas. Finalement, le principe d’objectivité spécifie que la quête de vérité en journalisme a pour méthode la production d’énoncés vérifonctionnels. Tel qu’ainsi entendu, le principe d’objectivité est tout à fait compatible avec l’idée de relativité conceptuelle et donc aussi avec la nature aspectuelle du journalisme. A worthwhile topic of study would be to examine the nature of journalism; not to circumscribe its boundaries, but to expose the presuppositions that govern its

  12. Concerning the acid dew point in waste gases from combustion processes

    Energy Technology Data Exchange (ETDEWEB)

    Knoche, K.F.; Deutz, W.; Hein, K.; Derichs, W.

    1986-09-01

    The paper discusses the problems associated with the measurement of acid dew point and of sulphuric acid-(say SO/sub 3/-)concentrations in the flue gas from brown coal-fired boiler plants. The sulphuric acid content in brown coal flue gas has been measured at 0.5 to 3 vpm in SO/sub 2/ concentrations of 200 to 800 vpm. Using a conditional equation, the derivation of which from new formulae for phase stability is described in the paper, an acid dew point temperature of 115 to 125/sup 0/C is produced.

  13. Development and testing of the EDF-2 reactor fuel element; Essais et mise au point de l'element combustible pour le reacteur EDF-2

    Energy Technology Data Exchange (ETDEWEB)

    Delpeyroux, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Furhmann, R [Societe Industrielle de Combustible Nucleaire (France)

    1964-07-01

    rassemble les etudes qui ont ete necessaires pour mener a bien la definition de l'element combustible EdF 2. Apres un bref rappel des caracteristiques du reacteur EdF 2 et des options preliminaires ayant permis de fixer un avant-projet d'element combustible, on aborde les etudes proprement dites: - Etudes uranium: essais de passage d'une couronne interne du tube en phase {beta}, flechage du tube sous l'action d'une force concentree, soudage des pastilles d'extremites et verification de leur etancheite. La tenue du tube a l'ecrasement et la resistance des pastilles a l'enfoncement sous l'action de la pression externe sont etudiees en detail dans un autre rapport CEA - Etudes gaine: rappel des conditions de fabrication et verification de l'etancheite de la gaine, tenue des ailettes au fluage sous l'action du courant gazeux - Etudes d'extremites: fluage en compression et soudage des bouchons a la gaine. - Etudes cartouche: determination des caracteristiques des gorges d'ancrage gaine-combustible et des conditions de gainage, verification de la tenue au cyclage thermique de l'element combustible, determination de la chute de temperature au contact gaine-combustible traitee en detail dans un autre rapport CEA, - Etudes de l'ensemble: les etudes se rapportant a la chemise de graphite, au support et aux vibrations de la cartouche ont ete traitees par le service des Etudes Mecaniques et Thermiques (Section de Mecanique), Dans ce domaine, la Section d'Etude d'Elements Combustibles a etudie la tenue des centreurs sous l'action du courant gazeux. L'aboutissement des etudes est constitue par le dessin de l'element combustible, le schema de fabrication et les normes de fabrication. La validite de l'ensemble de ces essais hors pile sera confirmee par des assais en pile qui sont en cours et par l'irradiation des elements dans le reacteur EdF 2 lui-meme. En conclusion, on donne l'orientation des etudes pour l'amelioration de l'element combustible et la definition d'un element combustible

  14. Une installation expérimentale pour l'étude du traitement par combustion des fumées industrielles An Experimental Plant for Processing Industrial Fumes by Combustion

    Directory of Open Access Journals (Sweden)

    Morillon R.

    2006-11-01

    Full Text Available Le rejet à l'atmosphère d'effluents gazeux d'origine industrielle entraîne un accroissement sensible de la pollution atmosphérique ; en outre, il s'accompagne souvent d'une perte d'énergie lorsque l'élément polluant est un hydrocarbure. Dans ce cas, l'utilisation du gaz naturel pour le traitement par combustion des fumées industrielles apporte une solution élégante et souvent peu coûteuse grâce à la récupération d'énergie qu'il est possible de faire. La première partie de l'article rappelle les aspects théoriques de ce traitement ; en particulier, l'influence des divers éléments sur son efficacité y est discutée (composition de l'atmosphère polluée, température, temps de séjour, etc.. II apparaît ainsi que diverses conditions doivent être remplies simultanément pour obtenir une efficacité satisfaisante. Afin de disposer d'éléments d'ingénierie permettant de construire les unités de traitement les plus efficaces et les plus sûres possible, au coût le plus bas possible, la Direction des études et techniques nouvelles du Gaz de France a réalisé une installation expérimentale qui est présentée dans la deuxième partie de l'article. Enfin, quelques examples d'utilisation de cette installation expérimentale, qui constitue un nouvel outil de travail mis à la disposition des utisitateurs et des constructeurs, sont décrits dans la troisième partie de l'article. The discharge into the atmosphere of industrial waste gases causes substantially increased air pollution. Moreover, it is often accompanied by loss of energy when the polluting element is a hydrocarbon. In such cases, the use of natural gas for processing industrial fumes by combustion provides an elegant solution, which moy often prove economical too becouse of the recovery of energy it makes possible. The first part of this article reviews the theoretical aspects of such processing. The way in which its effectiveness is affected by various parameters

  15. Costs of fuel cycle industrial facilities: an international review; Couts des installations industrielles du cycle du combustible point a l'international

    Energy Technology Data Exchange (ETDEWEB)

    Macias, R.M

    2004-07-01

    This document presents, comments, and compares economic and financial data for industrial facilities concerning different aspects of the nuclear fuel cycle. It first comments the present situation and the short term trends for the natural uranium market, the conversion market, the enrichment market, the reprocessing market, the storage market. It gives an assessment of the elementary costs of the existing facilities for the different stages and processes: reprocessing, spent fuel warehousing (example of the CLAB in Sweden and comparison with other available data), warehousing of all types of wastes (examples of Habog in Netherlands, Zwilag in Switzerland), spent fuel storage (example of Yucca Mountain in the USA, Onkalo in Finland, projects and studies in Sweden), storage of vitrified wastes in Belgium, storing of transuranic wastes in the USA, storage of low and intermediate level and short life wastes in Sweden.

  16. The Use of Fuel Gas as Stripping Medium in Atmospheric Distillation of Crude Oil L’utilisation de gaz combustible comme moyen d’extraction des fractions légères en distillation atmosphérique du pétrole brut

    Directory of Open Access Journals (Sweden)

    Plellis-Tsaltakis C.

    2011-09-01

    Full Text Available Stripping of petroleum fractions aims to remove the light ends that spoil some of their properties, such as the flash point. Stripping usually employs steam for that purpose. Except for steam, other substances can perform the same function, among them light hydrocarbons. In this article, we investigate the use of refinery fuel gas as stripping medium for a crude oil atmospheric distillation unit. L’extraction des fractions légères du pétrole vise à enlever les produits nuisibles à certaines propriétés comme le point d’éclair. Cette opération utilise habituellement de la vapeur d’eau. D’autres substances peuvent remplir la même fonction, comme les hydrocarbures légers. Dans cet article, on étudie l’utilisation du gaz combustible de la raffinerie comme moyen d’extraction des fractions légères dans une unité de distillation atmosphérique.

  17. Le médicament générique au Maroc: le point de vue du ...

    African Journals Online (AJOL)

    Introduction: Le médicament générique est souvent une origine de préjugés négatifs et de méfiance chez les professionnels de santé et les patients. Ceci pourrait être dû à plusieurs facteurs entre autre le manque des connaissances du patient sur ces médicaments. Le but de notre étude était d'évaluer l'information du ...

  18. AREVA Technical Days (ATD) session 2: operations of the back-end of the nuclear fuel cycle; AREVA Technical Days (ATD) session 2: les activites du pole Aval du cycle du combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    These technical days organized by the Areva Group aims to explain the group activities in a technological and economic point of view, to provide an outlook of worldwide energy trends and challenges and to present each of their businesses in a synthetic manner. This second session deals with the reprocessing business, back-end financing mechanisms, technology transfer, environmental management, risk management programs, research and development contribution to waste volume reductions, issues and outlook of nuclear wastes, comparison of the open and closed cycles. (A.L.B.)

  19. Qualification of the Darwin code for the studies of the fuel cycle relative to the boiling water reactors; Qualification du formulaire Darwin pour les etudes du cycle du combustible pour les reacteurs a eau bouillante

    Energy Technology Data Exchange (ETDEWEB)

    Allais, V

    1998-03-01

    This thesis was carried out in the framework of fuel cycles studies in partnership with COGEMA; the aim is to determine physics parameters characterising Boiling Reactor Assemblies. Those reactors Firstly distinguish themselves from Pressurised Water Reactor by the boiling of the moderator in the core and secondary by the strong neutronics heterogeneity due to complex design. The diphasic mixture formed is characterised by the void fraction parameter. The loss of information, and neutronic studies characteristics of Boiling Water Reactors led us to make preliminary studies having in view to quantify the void fraction impact on the isotopics evolution. Studies on neutronics influence of assemblies and control rods from the immediate environment allows to define the cluster size to describe. The radial description optimisation with APOLLO-2 is necessary to improve the calculation performance and to reduce the errors coming from the modelization. The following points were studied: pellet radial discretization, clustering of cells characterized by a similar behaviour, options in flux spatial calculation (interface current formalism), self-shielding optimisation (specific to each isotopes). The three dimensional modelization with CRONOS-2 and the simplified accounting of the thermohydraulics / neutronics coupling done by a procedure developed and written during this thesis, allow an evaluation of axial distribution of void fraction, power and burn-up during the irradiation. The comparison with experimental analytic results of complete assembly and pin samples dissolutions allows the qualification of this procedure and confirms the necessity to take into account the void fraction axial variation during the evolution. The application of an automatic coupling with the DARWIN cycle code will allow a precise burnup calculation to be utilized in an industrial procedure. (author)

  20. 20 fevrier 2012 - Le Vice-Président du Gouvernement Wallon et Ministre du Développement durable et de la Fonction Publique en charge de l’Energie du Logement et de la Recherche J.-M. Nollet, Royaume de Belgique, visite la salle de contrôle de CMS au Point 5, la caverne expérimentale CMS et le hall de tests des aimants supraconducteurs du LHC. Les chefs de département T. Lagrange et F. Hemmer accompagnent la délégation. L. Walckiers guide la visite SM18.

    CERN Multimedia

    Maximilien Brice

    2012-01-01

    20 fevrier 2012 - Le Vice-Président du Gouvernement Wallon et Ministre du Développement durable et de la Fonction Publique en charge de l’Energie du Logement et de la Recherche J.-M. Nollet, Royaume de Belgique, visite la salle de contrôle de CMS au Point 5, la caverne expérimentale CMS et le hall de tests des aimants supraconducteurs du LHC. Les chefs de département T. Lagrange et F. Hemmer accompagnent la délégation. L. Walckiers guide la visite SM18.

  1. Etude du point critique des paliers lisses alimentés à la graisse Study of Critical Point on Plain Bearings Lubricated by Grease

    Directory of Open Access Journals (Sweden)

    Delneuville P.

    2006-11-01

    Full Text Available Cet article est essentiellement consacré à l'étude du fonctionnement limite des paliers lisses lubrifiés à la graisse ; son but est de permettre la détermination des conditions nécessaires à l'obtention d'un film lubrifiant d'épaisseur suffisante. L'auteur cherche à cette occasion une loi théorique qui permet de départager les régimes de lubrification, non plus empiriquement, mais sur la base de lois statistiques. La formulation finale doit permettre aux utilisateurs de situer correctement les conditions de fonctionnement d'un palier lisse et d'en estimer la sécurité du régime. This article deals essentially with the boundary behaviour of plain bearings lubricated by grease. Its aim is to determine the conditions required to obtain a sufficiently thick lubricating film. The author proposes a theoretical law for separating lubrication types. This law is not empirical but is based on statistical laws. The final formulation should enable users to correctly situate the operating conditions of a plain bearing and to evaluate the safety factor during running.

  2. Contribution to the study of the fission-gas release in metallic nuclear fuels; Contribution a l'etude du degagement des gaz de fission dans les combustibles nucleaires metalliques

    Energy Technology Data Exchange (ETDEWEB)

    Kryger, B [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1969-10-01

    In order to study the effect of an external pressure on the limitation of swelling due to fission-gas precipitation, some irradiations have been carried out at burn-ups of about 35.000 MWd/ton, and at average sample temperatures of 575 Celsius degrees, of non-alloyed uranium and uranium 8 per cent molybdenum gained in a thick stainless steel can. A cylindrical central hole allows a fuel swelling from 20 to 33 per cent according to the experiment. After irradiation, the uranium samples showed two types of can rupture: one is due to the fuel swelling, and the other, to the pressure of the fission gases, released through a network of microcracks. The cans of the uranium-molybdenum samples are all undamaged and it is shown that the gas release occurs by interconnection of the bubbles for swelling values higher than those obtained in the case of uranium. For each type of fuel, a swelling-fission gas release relationship is established. The results suggest that good performances with a metallic fuel intended for use in fast reactor conditions can be obtained. (author) [French] Afin d'etudier l'effet d'une pression exterieure sur la limitation du gonflement due a la precipitation des gaz de fission, on a irradie a des taux de combustion d'environ 35.000 MWj/t et a des temperatures moyennes de 575 degres des echantillons d'uranium non allie et d'uranium-molybdene 8 pour cent contenus dans une gaine en acier inoxydable epaisse. Un trou cylindrique central permet au combustible de gonfler librement de 20 a 33 pour cent suivant les cas. Apres irradiation les echantillons d'uranium presentent deux types de ruptures de gaine: l'une due au gonflement du combustible, l'autre a la pression des gaz degages, ce degagement des gaz etant provoque par un reseau de micro-fissures. Les gaines des echantillons d'alliage uranium-molybdene sont toutes intactes et l'on montre que le relachement des gaz opere par interconnexion des bulles pour des valeurs de gonflement plus elevees que dans

  3. Review of safety precautions derived from six-year experience of a spent fuel reprocessing plant - Centre de Marcoule; Elements de securite tires de six annees d'exploitation de l'usine de traitement de combustibles irradies du Centre de Marcoule

    Energy Technology Data Exchange (ETDEWEB)

    Rodier, J [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1964-07-01

    an organization of the work aimed at eliminating the causes of incidents. They investigate the following points in particular: - frequency of entry into forbidden zones during normal functioning - the distribution of exceptional tasks - the prevention of criticality risks - zone contamination incidents - the volume and nature of decontaminated material and eliminated residues - the evolution and distribution of external irradiation doses received by the workers - the frequency of cases of body contamination - internal contamination fixed in the organisms of workers. Conclusions are drawn from the different incidents which have occurred during the years of operating the plant. (author) [French] Dans une usine de traitement de combustibles irradies comme dans toute autre usine, la continuite de la production ne peut etre obtenue que par une recherche constante de la securite. Les auteurs examinent les elements de securite apportes par la conception des installations tant au point de vue de la securite classique que de la securite radiologique. Dans l'industrie nucleaire, il ne suffit pas, en effet, d'adopter seulement les precautions habituelles prises contre les risques d'explosion, d'incendie...; il faut aussi apporter beaucoup d'attention aux problemes poses par le confinement des matieres, la radioactivite et les risques de criticite. Les principes generaux de la prevention technique contre les risques radioactifs sont maintenant bien connus. Leur application doit se traduire des la conception des installations par des dispositions concernant: - la conception et la realisation des installations vis-a-vis des risques deja enumeres, - la division de l'usine en zones, - la circulation du personnel et du materiel, - la ventilation et l'epuration de l'air. Les facteurs techniques de securite ne sont toutefois pas suffisants a eux seuls. Quelle que soit la qualite du materiel et le degre d'automatisme atteint, la continuite de fonctionnement d'une usine implique l

  4. Path planning during combustion mode switch

    Science.gov (United States)

    Jiang, Li; Ravi, Nikhil

    2015-12-29

    Systems and methods are provided for transitioning between a first combustion mode and a second combustion mode in an internal combustion engine. A current operating point of the engine is identified and a target operating point for the internal combustion engine in the second combustion mode is also determined. A predefined optimized transition operating point is selected from memory. While operating in the first combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion engine to approach the selected optimized transition operating point. When the engine is operating at the selected optimized transition operating point, the combustion mode is switched from the first combustion mode to the second combustion mode. While operating in the second combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion to approach the target operating point.

  5. Development of Non-Metallic Fuel Elements for a High-Temperature Gas-Cooled Reactor; Mise au point d'elements combustibles non metalliques pour un reacteur a haute temperature, refroidi par un gaz; Razrabotka nemetallicheskikh teplovydelyashchikh ehlementov dlya vysokotemperaturnogo reaktora s gazovym okhlazhdeniem; Elementos combustibles no metalicos para un reactor de temperatura elevada refrigerado por gas

    Energy Technology Data Exchange (ETDEWEB)

    Liebmann, B.; Schafer, L.; Spener, G. [NUKEM, Nuklear-Chemie und -Metallurgie G.m.b.H., Wolfgang bei Hanau, Federal Republic of Germany (Germany)

    1963-11-15

    un gaz, de la societe Brown-Boveri/Krupp Reaktorbau GmbH, on a retenu et mis au point deux types differents d'elements combustibles. Dans les deux cas, l'element combustible est constitue par une sphere en graphite de 6 cm de diametre enrobant un noyau de matiere combustible ayant la forme d'une pastille cylindrique d'environ 20 mm de diametre et de 16 mm de hauteur. Les deux types different par le noyau aussi bien que par la preparation de la sphere en graphite. Dans le premier type, le noyau est un melange d'UO{sub 2} et de graphite. La preparation consiste a melanger U{sub 3}O{sub 8} et du graphite, a les comprimer en pastilles et a faire reagir les deux composants du melange dans un four sous vide a 1800{sup o}C. Le rapport atomique U : C est 1:45. Etant donne que ce type de pastille ne retient pas completement les produits de fission, il a fallu impregner la sphere en graphite, de maniere a la rendre etanche aux produits de fission. On a pu realiser des permeabilites de l'ordre de 10{sup -6}cm{sup 2}/s . Dans le deuxieme type, le noyau est une solution solide de UC dans ZrC; il est revetu d'une couche de ZrC. Le rapport molaire UC : ZrC est 1 : 20. La preparation de la pastille de combustible s'effectue de la maniere suivantes UO{sub 2}, ZrO{sub 2} et le graphite sont melanges et comprimes en pastilles. On fait reagir le melange pour obtenir les carbures. Le broyage des carbures est suivi d'un pressage a chaud a des temperatures de l'ordre de 2000{sup o}C. On est parvenu a des densites egales a 95% de la densite theorique. Les auteurs decrivent en detail la preparation des pastilles de combustible et mentionnent un certain nombre de leurs proprietes physiques. On pense qu'en raison de leur capacite de retention des gaz de fission, des noyaux de ce type pourront etre enrobes dans des spheres en graphite non impregne. L'etude fait encore etat d'autres avantages de ce genre de combustible. [Spanish] En relacion con el perfeccionamiento de los elementos combustibles

  6. Experimental apparatus for in-pile studies of: creep of nuclear fuels, and Young's-modulus of structural materials; Dispositifs experimentaux pour etudes en pile du fluage des materiaux combustibles, et du module d'elasticite des materiaux de structure

    Energy Technology Data Exchange (ETDEWEB)

    Gautier, A; Le Bret, P; Alfille, L; Pesenti, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Creep test under compression: the apparatus described allows to study, in an horizontal beam hole of a research reactor such as EL2, the creep behaviour of nuclear fuel samples under neutron flux. The maximum stress applied on the specimens is a constant compression chooses between 0.200 and 0.400 kg/mm{sup 2} (285 psi and 570 psi). - Young's Modulus measurement: in another horizontal beam hole of such a reactor, an apparatus allows to study the irradiation effect on Young's Modulus of a structural material specimen. (author)Fren. [French] Essai de fluage en compression: l'appareillage decrit permet d'etudier, dans un canal horizontal d'une pile experimentale type EL2, le fluage en compression d'eprouvettes de materiaux fissiles sous le flux de neutrons, sous une contrainte maximum de 500 g/mm{sup 2}. - Mesure du module d'Young: dans un canal identique au precedent, un appareillage permet de suivre l'influence du rayonnement sur le module d'elasticite d'une eprouvette d'un materiau de structure. (auteur)

  7. Experimental study of a separated jets burner: application to the natural gas-pure oxygen combustion; Etude experimentale du comportement de bruleurs a jets separes: application a la combustion gaz naturel-oxygene pur

    Energy Technology Data Exchange (ETDEWEB)

    Salentey, L.

    2002-04-15

    The evolution of pollution standards and the optimisation of furnaces performances require a development of new burner generation and also the improvement of combustion techniques. Actually, the use of oxy-combustion in separated jets burners offers interesting prospects for NO{sub x} emission reduction and on the modularity of flames properties (lift off, flame front topology, flame length). The complex geometry of those burners leads to several problems like the three-dimensional character of the flow, which may sometimes disturb the flame stability as flames are lifted above the burner. This experimental study deals with a simplified version of that kind of burner constituted with a central natural gas jet surrounded by two oxygen jets. Primary, the study of non-reactive jet was planned in order to understand dynamic and mixture phenomena involved between jets and to provide a database useful for the computer code validation. The reactive flow developed in a furnace, which simulates the real conditions, had been characterised. The studies of the dynamic field using Laser Doppler Velocimetry (LDV) and of the turbulent mixture by conditional Laser tomography were supplemented in combustion by the visualisation of the spontaneous emission of radical OH, in the initial and final zone of the oxy-flames, like by the measurement of pollutants like NO{sub x} and soot. The measurements carried out while varying speeds of injection as well as the gap between the jets made possible the highlight of the influence of these parameters upon the stabilisation of the oxy-flames as well as the modification of the topology and the characteristics of the flows. The comparison of the measurements made in non-reactive and reactive flow shows the influence of oxy-combustion on the dynamic and scalar development of the flow for this type of burners. (author)

  8. A Study on the Role of Reaction Modeling in Multi-phase CFD-based Simulations of Chemical Looping Combustion; Impact du modele de reaction sur les simulations CFD de la combustion en boucle chimique

    Energy Technology Data Exchange (ETDEWEB)

    Kruggel-Emden, H.; Stepanek, F. [Department of Chemical Engineering, South Kensington Campus, Imperial College London, SW7 2AZ, London (United Kingdom); Kruggel-Emden, H.; Munjiza, A. [Department of Engineering, Queen Mary, University of London, Mile End Road, E1 4NS, London (United Kingdom)

    2011-03-15

    Chemical Looping Combustion is an energy efficient combustion technology for the inherent separation of carbon dioxide for both gaseous and solid fuels. For scale up and further development of this process multi-phase CFD-based simulations have a strong potential which rely on kinetic models for the solid/gaseous reactions. Reaction models are usually simple in structure in order to keep the computational cost low. They are commonly derived from thermogravimetric experiments. With only few CFD-based simulations performed on chemical looping combustion, there is a lack in understanding of the role and of the sensitivity of the applied chemical reaction model on the outcome of a simulation. The aim of this investigation is therefore the study of three different carrier materials CaSO{sub 4}, Mn{sub 3}O{sub 4} and NiO with the gaseous fuels H{sub 2} and CH{sub 4} in a batch type reaction vessel. Four reaction models namely the linear shrinking core, the spherical shrinking core, the Avrami-Erofeev and a recently proposed multi parameter model are applied and compared on a case by case basis. (authors)

  9. Effect of Ash on Oxygen Carriers for the Application of Chemical Looping Combustion to a High Carbon Char Effet des cendres sur l’activité des porteurs d’oxygène dans la combustion du charbon en boucle chimique

    Directory of Open Access Journals (Sweden)

    Rubel A.

    2011-02-01

    activity of the OCs and both OCs performed well. The results were promising for the application of CLC directly to solid fuels. L’application de la combustion en boucle chimique (CLC aux combustibles solides est actuellement étudiée à l’Université du Kentucky, au Centre de Recherche de l’Energie Appliquée (CAER dans le but de développer un procédé de gazéification/combustion en boucle chimique pressurisé (PCLC/G afin de générer de l’électricité à partir de charbon. Un des principaux aspects de la combustion en boucle chimique de combustibles solides est la compréhension de l’effet des cendres sur la réactivité des porteurs d’oxygène (OCs. L’effet des cendres sur la capacité de transfert d’oxygène et sur l’aptitude à oxyder le charbon est étudié avec deux porteurs d’oxygène à base d’oxydes de fer. Les cendres utilisées sont des cendres volantes provenant d’une centrale thermique au charbon. Les expériences sont réalisées dans un système composé d’une thermo-balance couplée à un spectrographe de masse (TGMS dans lequel on utilise d’abord 500 mg d’un mélange de cendres/porteurs d’oxygène à différentes concentrations de cendres allant jusqu’à 75 %. Le gaz réducteur est composé de 10 % de H2, 15 % de CO, 20 % de CO2 et de 55 % de Ar; et le gaz oxydant est composé de 20 % de O2 dans Ar. Les réactions d’oxydation/réduction sont quasi totales. D’après ces expériences, les cendres ont une activité propre de porteur d’oxygène, liée à la présence de fer dans les cendres, confirmée par les analyses DRX. Cela génère une augmentation du gain ou de la perte de masse du mélange pendant l’oxydation/réduction. Les vitesses d’oxydation/réduction augmentent avec la concentration des cendres à cause de l’augmentation de la porosité du mélange de porteurs d’oxygène avec les cendres, ce qui permet un meilleur accès des gaz réactifs sur les sites actifs des porteurs d’oxygène. Dans un

  10. Socialisme, Communisme, Totalitarisme : quelle différence pour une recherche historique du point de vue moral ?

    Directory of Open Access Journals (Sweden)

    Momchil Hristov

    2009-12-01

    Full Text Available The essay focuses on recent developments in the field of history of socialist/ communist regime in Bulgaria. The author considers this form of disciplinary knowledge as a set of discourses and draws his research material from a number of interviews with researchers (mostly historians, but also anthropologists and sociologists in the field. The attempt is made to elucidate the “moral base” and potential political implications of the existing demarcation and differentiation between different approaches to this still burning subject. The accent is put on the individual (and collective choice of labeling the epoch – socialism, communism, or totalitarianism. Those three labels are used in order to construct three ideal types of historical-sociological research and to indicate the methodological specificities of every type of research as well as itsparticular objects of study. Finally a point is made on the danger which a close relationship between a study and politics represents to the relative research autonomy.

  11. Formation and destruction mechanisms of nitrogen oxides during coal combustion in circulating fluidized beds; Mecanismes de formation et de destruction des oxydes d`azote lors de la combustion du charbon en lit fluidise circulant

    Energy Technology Data Exchange (ETDEWEB)

    Borrel, G.; Lecuyer, I. [Universite du Haut-Rhin, 68 - Mulhouse (France)

    1997-01-01

    Formation and reduction of nitrogen oxides (NO and N{sub 2}O) during coal combustion in a circulating fluidized bed (CFBC) are very complicated and yet badly known. The aim of the present study was to better characterize these phenomena on a small-sized experimental unit (reactor diameter: 5 cm), with the possibility to re-inject the solids in the bottom of the furnace, as in a real industrial unit. This should allow then to develop a numerical set of chemical reactions involving the nitrogen oxides. The experimental results showed that coal ash plays a great role in reducing nitrogen oxides, the determining parameter being the quantity of unburnt carbon remaining in the ash. The study then detailed the interaction between nitrogen oxides and de-volatilized (char) according to the temperature, NO{sub x} concentration and the mass of solid. In the absence of oxygen small quantities of char can very significantly reduce NO as well as N{sub 2}O. It was possible to establish destruction kinetics on these particles, and orders of reaction could be determined versus the NO{sub x} concentration and the char particle mass (heterogeneous phase chemical reactions). Then, the coal pyrolysis study enabled to identify the products released during coal devolatilization and thermogravimetric analyses displayed several successive weight losses due CO, CO{sub 2} and CH{sub 4} releases, during a linear temperature increase. Lastly coal combustion was studied in the small pilot with variable experimental conditions. Using the previous experimental was studied in the small pilot with variable experimental conditions. Using the previous experimental results, a model was developed to calculate NO{sub x} concentrations during the coal combustion and validated. The NO and N{sub 2}O contents calculated are thoroughly correlated with the experimental data whatever the injection carbon/oxygen ratio is. (author) 96 refs.

  12. 3-D Resistivity Tomography for Cliff Stability Study at the D-Day Pointe du Hoc Historic Site in Normandy, France

    Science.gov (United States)

    Udphuay, S.; Everett, M. E.; Guenther, T.; Warden, R. R.

    2007-12-01

    The D-Day invasion site at Pointe du Hoc in Normandy, France is one of the most important World War II battlefields. The site remains today a valuable historic cultural resource. However the site is vulnerable to cliff collapses that could endanger the observation post building and U.S. Ranger memorial located just landward of the sea stack, and an anti-aircraft gun emplacement, Col. Rudder's command post, located on the cliff edge about 200 m east of the observation post. A 3-D resistivity tomography incorporating extreme topography is used in this study to provide a detailed site stability assessment with special attention to these two buildings. Multi-electrode resistivity measurements were made across the cliff face and along the top of the cliff around the two at-risk buildings to map major subsurface fracture zones and void spaces that could indicate possible accumulations and pathways of groundwater. The ingress of acidic groundwater through the underlying carbonate formations enlarges pre-existing tectonic fractures via limestone dissolution and weakens the overall structural integrity of the cliff. The achieved 3-D resistivity tomograms provide diagnostic subsurface resistivity distributions. Resistive zones associated with subsurface void spaces have been located. These void spaces constitute a stability geohazard as they become significant drainage routes during and after periods of heavy rainfalls.

  13. [Undesirable effects of medicine in the Internal Medicine Service of the University Hospital Center du Point G].

    Science.gov (United States)

    Soukho-Kaya, A; Minta, D K; Diarra, M T; Konaté, A; Diallo, B; Sidibé, A T; Dembélé, M; Bah, M; Doumbia, A A; Dao, K; Tolo, N; Camara, B D; Sy, D; Maiga, M Y; Traoré, H A

    2010-01-01

    The aim of this study was to determine the frequency of adverse reactions to drugs, the WHO grade, describe the clinical features and identify the drug responsible. This was a descriptive cross-sectional study which took place from February 2005 to January 2006 in the Internal Medicine Department at the hospital point G. Were included in this study, all patients hospitalized during the study period, which presented adverse drug reactions (ADRs) that the relation of cause and effect was certain or likely. Thus, 47 ADRs were identified in 39 patients of 426 admitted during the same period a frequency of 9.2%. The average age of our patients was 48.5 ± 16.5 years. The sex-ratio was 1.6 for women. Eighty-two percent of our patients had an ADR and 18% more than one. The WHO grade 1 was the most met or 36.2%, followed by grades 4 and 2 respectively 27.7% and 25.5%. Antidiabetics were responsible for adverse reactions in 46.8% and 21.3% in TB. Adverse events were neurological in 53.2% and type of manifestations of hypoglycemia 46.8% (22/47 cases), polyneuritis 6.4% (3 / 47 cases) and 29.8% in digestive cases dominated by vomiting 12.8% (6 / 47 cases), the epigastria pain 6.4% (3 / 47 cases). The outcome was favorable in 87.2% of cases, however, 3 cases of death among those over 60 years all grade 4 WHO. ADRs deserve special attention to this high death rate (6.4% 3/47 cases) where the interest to search systematically for all patients under medical treatment with a good clinical examination and questioning some thoroughly.

  14. The Non-Destructive Testing of Fuel Elements and Their Components for the United Kingdom Power-Reactor Development Programme; Controle Non Destructif des Elements Combustibles et de Leurs Parties Constitutives dans le Cadre du Programme de Developpement des Reacteurs de Puissance au Royaume-Uni; Nedestruktivnoe ispytanie teplovydelyayushchikh ehlementov i ikh komponentov dlya osushchestvleniya programmy soedinennogo korolevstva po razrabotke ehnergeticheskikh reaktorov; Ensayo No Destructivo de Elementos Combustibles y sus Componentes, en el Marco del Programa de Reactores de Potencia del Reino Unido

    Energy Technology Data Exchange (ETDEWEB)

    Mann, C. A.; Campsie, I. C. [U.K.A.E.A., Reactor Fuel Element Laboratories, Springfields, Salwick, Preston, Lancs. (United Kingdom)

    1965-10-15

    and the ends closed. In addition, the integrity of end closures is established, by radiography. Multiple exposures are commonly made to examine the whole of circumferential weld adequately. The disposition of the fuel can also be recorded accurately by using a panoramic technique. The use of colour radiography is also discussed. Pins are normally tested for leakage after filling with helium, using a mass-spectrometer leak detector. Pins not filled with helium may be tested using a ''back-pressurizing'' technique. Conventional ''probing'' and ''sniffing'' methods are used when it is desirable to locate the sites of leaks. The bubble test in liquids is also used, as a cheap and simple test. The use of krypton-85 as a tracer gas is discussed. (author) [French] Les auteurs decrivent les methodes d'essai que les laboratoires charges des elements combustibles ont elaborees dans le cadre du programme etabli par le en vue de mettre au point des aiguilles de combustible pour diverses filieres de reacteurs. Ces aiguilles sont contenues dans des gaines de 5 a 15 mm de diametre, les materiaux utilises etant des aciers inoxydables et des alliages de zirconium, a) Detection de defauts dans les gaines. Examen par ultrasons a l'aide de deux traducteurs immerges. Les tubes sont animes d'un mouvement helicoidal rapide dans un reservoir fixe. Chaque signal de defaut est verifie et enregistre. Pour regler le dispositif et verifier sa stabilite, on utilise comme temoins des fentes'pratiquees a l'arc a la surface des tubes. Dans certains cas, on a egalement recours au controle par courants de Foucault. Les auteurs decrivent deux procedes: l'un, a debit rapide, est fonde sur un systeme de bobines encerclant le tube; l'autre, a exploration heliccfldale, utilise une bobine se deplacant le long du tube. Les signaux fournis par un circuit a pont sont selectionnes selon la phase et filtres, pour des frequences de 30 a 60 kHz. b) Controle des dimensions de tubes et de

  15. Visualisation of Gasoline and Exhaust Gases Distribution in a 4-Valve Si Engine; Effects of Stratification on Combustion and Pollutants Visualisation de la répartition du carburant et des gaz brûlés dans un moteur à 4 soupapes à allumage commandé ; effet de la stratification sur la combustion et les polluants

    Directory of Open Access Journals (Sweden)

    Deschamps B.

    2006-12-01

    des dégagements d'énergie et des émissions de polluants très distincts. Le niveau de tumbleet l'emplacement de l'étincelle sont aussi modifiés. L'observation de la stratification telle qu'elle est réellement dans le moteur constitue un moyen pertinent pour expliquer ses performances. Les paramètres permettant d'optimiser les niveaux de NOx et d'HC peuvent en être déduits, de même que l'efficacité des stratégies de recirculation et d'injection du carburant. Les résultats des visualisations ont été confirmés par des mesures obtenues dans un moteur monocylindre muni d'une culasse conventionnelle avec la même géométrie de chambre de combustion.

  16. 1er mars 2017 - Signature du livre d'or, visite du tunnel du LHC au Point 5 et de la caverne expériementale de CMS par le Secrétaire d’Etat français aux Affaires européennes auprès du ministre des Affaires étrangères et du Développement international H. Désir.

    CERN Multimedia

    Bennett, Sophia Elizabeth

    2017-01-01

    Entourent le Secrétaire d'Etat pendant la signature du livre d'or: Le Préfet de l’Ain A. Cochet; le Directeur des accélérateurs et de la technologie F. Bordry; Ambassadeur, Représentant permanent de la France auprès de l’Office des Nations Unies à Genève et des Organisations internationales en Suisse E. Laurin; la Directrice générale du CERN F. Gianotti et la Directrice des relations internationales C. Warakaulle. Sont également présents: H. Bertrand, Maire de Saint-Genis-Pouilly; C. Bouvier, Maire de Cessy; G. Rousseau, Secrétaire Général de la sous-préfecture de Gex; Y. Mecibah, Directrice de Cabinet du Maire de Saint-Genis-Pouilly; F. Croquette, Ambassadeur pour les droits de l’homme, chargé de la dimension internationale de la Shoah, des spoliations et du devoir de mémoire; S. Bonbayl, Conseillère technique, Cabinet du Secrétaire d’Etat chargé des Affaires Européennes au MAEDI; F. Cormon-Veyssière, Sous-Directrice des droits de l’Homme et des Affaires humanitaires au MAEDI...

  17. Study of physico-chemical release of uranium and plutonium oxides during the combustion of polycarbonate and of ruthenium during the combustion of solvents used in the reprocessing of nuclear fuel; Etude de la mise en suspension physico-chimique des oxydes de plutonium et d'uranium lors de la combustion de polycarbonate et de ruthenium lors de la combustion des solvants de retraitement du combustible irradie

    Energy Technology Data Exchange (ETDEWEB)

    Bouilloux, L

    1998-07-01

    The level of consequences concerning a fire in a nuclear facility is in part estimated by the quantities and the physico-chemical forms of radioactive compounds that may be emitted out of the facility. It is therefore necessary to study the contaminant release from the fire. Because of the multiplicity of the scenarios, two research subjects were retained. The first one concerns the study of the uranium or plutonium oxides chemical release during the combustion of the polycarbonate glove box sides. The second one is about the physico chemical characterisation of the ruthenium release during the combustion of an organic solvent mixture (tributyl phosphate-dodecane) used for the nuclear fuel reprocessing. Concerning the two research subjects, the chemical release, i.e. means the generation of contaminant compounds gaseous in the fire, was modelled using thermodynamical simulations. Experiments were done in order to determine the ruthenium release factor during solvent combustion. A cone calorimeter was used for small scale experiments. These results were then validated by large scale tests under conditions close to the industrial process. Thermodynamical simulations, for the two scenarios studied. Furthermore, the experiments on solvent combustion allowed the determination of a suitable ruthenium release factor. Finally, the mechanism responsible of the ruthenium release has been found. (author)

  18. Determination of the Effectiveness of Control Rods in the VVER Reactor Fuel Assemblies; Determination de l'Efficacite des Barres de Reglage dans les Ensembles Combustibles du reacteur VVER; Opredelenie ehffektivnosti reguliruyushchikh sterzhnej v sborkakh reaktora VVEHR; Determinacion de la Eficacia de las Barras de Control en los Conjuntos de Elementos Combustibles del Reactor VVER

    Energy Technology Data Exchange (ETDEWEB)

    Semenov, V. N.; Lunin, G. L.; Komissarov, L. V.; Kamyshan, A. N.; Halizev, V. I.; Andrianov, G. Ja.; Voznesenskij, V. A.; Kuz' micheva, V. A.; Lebedev, V. I. [Ordena Lenina Institut Atomnoj Energii Im. I.V. Kurchatova, Moskva, SSSR (Russian Federation)

    1964-06-15

    The paper describes experiments done in homogeneous mock-ups of the fuel assemblies from the VVER Reactor (at one level of enrichment) to determine the effectiveness of absorbing systems comprising shim fuel assemblies or water cavities and of absorbing rods clad in jackets made of differing materials. The paper also gives data on some experiments that have been done in mock-ups of assemblies with differing levels of enrichment. These experiments make it possible to verify the methods used in calculation and to evaluate the prospects of using them for heterogeneous reactors. (author) [French] Le memoire decrit les experiences qui ont ete faites pour determiner l 'efficacite des absorbants contenus dans les barres de compensation, l'effet cavitaire et l 'efficacite des absorbants gaines de materiaux divers, au moyen d'assemblages homogenes de cartouches de combustible du reacteur VVER (reacteur de puissance ralenti et refroidi a l 'eau ayant le meme taux d'enrichissement. On y trouve en outre des donnees sur certaines experiences executees a l 'aide d'assemblages de cartouches de combustible taux d'enrichissement differents. Ces travaux permettent de verifier la methode de calcul et d'evaluer ses possibilites d'application aux reacteurs non homogenes. (author) [Spanish] Se describen en la memoria experimentos para determinar la eficacia de los materiales absorbentes contenidos en las barras de compensacion, el efecto de cavitacion y la eficacia de los materiales absorbentes revestidos de diversos materiales, realizados con ayuda de los conjuntos homogeneos de elementos combustibles del reactor VVER (reactor de potencia moderado y refrigerado por agua) con un solo grado de enriquecimiento. Ademas, se exponen datos sobre los experimentos efectuados con ayuda de conjuntos de grados de enriquecimientos; variados. Tales experimentos permiten verificar el metodo de calculo teorico, utilizad o y evaluar la posibilidad de aplicarlo a los reactores no homogeneos. (author

  19. Ecologie du phytoplancton du lac Kivu

    Directory of Open Access Journals (Sweden)

    Sarmento, H.

    2008-01-01

    Full Text Available Speciation within the African Coffee Pathogen. Cet article analyse s'il est avantageux d'utiliser le compost au lieu de l'engrais minéral pour produire la laitue dans la zone urbaine et péri-urbaine de Yaoundé. Les résultats de terrain montrent l'obtention de rendements et profits plus élevés lorsqu'on utilise le compost. Les résultats de la fonction de production Cobb-Douglas prouvent que l'utilisation du compost est statistiquement significative pour expliquer la variation de rendement de la laitue et que le compost est l'intrant le plus productif. D'autres résultats montrent que le compost fournit la matière organique utile au sol et que les besoins d'irrigation en eau de la culture sont réduits grâce à l'utilisation du compost. Par conséquent, malgré le fait que l'application du compost demande une main-d'oeuvre beaucoup plus élevée, son utilisation est généralement bénéfique pour les agriculteurs vivant aux alentours de Yaoundé. Les programmes de vulgarisation de cet intrant pour encourager son adoption devraient donc figurer parmi les points prioritaires dans la politique agricole du gouvernement camerounais.

  20. Behavior of silicon in nitric media. Application to uranium silicides fuels reprocessing; Comportement du silicium en milieu nitrique. Application au retraitement des combustibles siliciures d'uranium

    Energy Technology Data Exchange (ETDEWEB)

    Cheroux, L

    2001-07-01

    Uranium silicides are used in some research reactors. Reprocessing them is a solution for their cycle end. A list of reprocessing scenarios has been set the most realistic being a nitric dissolution close to the classic spent fuel reprocessing. This uranium silicide fuel contains a lot of silicon and few things are known about polymerization of silicic acid in concentrated nitric acid. The study of this polymerization allows to point out the main parameters: acidity, temperature, silicon concentration. The presence of aluminum seems to speed up heavily the polymerization. It has been impossible to find an analytical technique smart and fast enough to characterize the first steps of silicic acid polymerization. However the action of silicic species on emulsions stabilization formed by mixing them with an organic phase containing TBP has been studied, Silicon slows down the phase separation by means of oligomeric species forming complex with TBP. The existence of these intermediate species is short and heating can avoid any stabilization. When non irradiated uranium silicide fuel is attacked by a nitric solution, aluminum and uranium are quickly dissolved whereas silicon mainly stands in solid state. That builds a gangue of hydrated silica around the uranium silicide particulates without preventing uranium dissolution. A small part of silicon passes into the solution and polymerize towards the highly poly-condensed forms, just 2% of initial silicon is still in molecular form at the end of the dissolution. A thermal treatment of the fuel element, by forming inter-metallic phases U-Al-Si, allows the whole silicon to pass into the solution and next to precipitate. The behavior of silicon in spent fuels should be between these two situations. (author)

  1. Thermo-mechanical behaviour modelling of particle fuels using a multi-scale approach; Modelisation du comportement thermomecanique des combustibles a particules par une approche multi-echelle

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, V.

    2009-12-15

    Particle fuels are made of a few thousand spheres, one millimeter diameter large, compound of uranium oxide coated by confinement layers which are embedded in a graphite matrix to form the fuel element. The aim of this study is to develop a new simulation tool for thermo-mechanical behaviour of those fuels under radiations which is able to predict finely local loadings on the particles. We choose to use the square finite element method, in which two different discretization scales are used: a macroscopic homogeneous structure whose properties in each integration point are computed on a second heterogeneous microstructure, the Representative Volume Element (RVE). First part of this works is concerned by the definition of this RVE. A morphological indicator based in the minimal distance between spheres centers permit to select random sets of microstructures. The elastic macroscopic response of RVE, computed by finite element has been compared to an analytical model. Thermal and mechanical representativeness indicators of local loadings has been built from the particle failure modes. A statistical study of those criteria on a hundred of RVE showed the significance of choose a representative microstructure. In this perspective, a empirical model binding morphological indicator to mechanical indicator has been developed. Second part of the work deals with the two transition scale method which are based on the periodic homogenization. Considering a linear thermal problem with heat source in permanent condition, one showed that the heterogeneity of the heat source involve to use a second order method to localized finely the thermal field. The mechanical non-linear problem has been treats by using the iterative Cast3M algorithm, substituting to integration of the behavior law a finite element computation on the RVE. This algorithm has been validated, and coupled with thermal resolution in order to compute a radiation loading. A computation on a complete fuel element

  2. Instruments used to measure or check {alpha}, {beta}, {gamma} activity and neutron emission in the course of processing ore or irradiated fuel; Appareils de mesure ou de controle {alpha}, {beta}, {gamma}, n, des circuits des usines de traitement du minerai ou du combustible irradie

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, A; Brunet, M; Kermagoret, M; Labeyrie, J; Roux, G; Vasseur, J; Weil, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1959-07-01

    One of the methods checking ores in the course of treatment is the rapid quantitative determination of thorium. This measurement is carried out by means of a scintillation instrument which shows the {beta} and {alpha} coincidences of ThC and ThC'. The treatment of irradiated fuel is accompanied by a large number of radioactive checks relative to the performance of the fixation and elution operations of uranium in the ion exchangers, to the concentration of radioactivity of effluent sent from the plant into watercourses. The operations of fixation and elution of the uranium are checked automatically by an instrument which takes a sample of 5 cm{sup 3} of solution, evaporates it and measures its activity every 10 or 20 minutes. Plutonium concentrations are measured: - in the presence of strong {beta} {gamma} activities, by means of rotating cylinder detectors; - in the presence of weak {beta} {gamma} activities, by means of {alpha} detectors scanning a constant level liquid surface; - by means of fission chambers relatively insensitive to {gamma}. Fission product concentrations are measured by chambers, counters or scintillators, according to the amount of {gamma} activity present. Finally, the activity of effluent to be emptied into watercourses is checked by means of a scintillation instrument, which measures the {alpha} activity on the one hand, and on the other hand the {beta} {gamma} activity of residue from a 100 cm{sup 3} sample taken and evaporated in 20 minutes. (author) [French] Parmi les controles relatifs au minerai en cours de traitement, figure le dosage rapide de thorium. Cette mesure est realisee au moyen d'un appareillage a scintillation qui met en evidence la coincidence des emissions {beta} et {alpha} du ThC et du ThC'. Le traitement des combustibles irradies s'accompagne d'un grand nombre de controles radioactifs portant sur le fonctionnement des operations de fixation et d'elution de l'uranium dans les echangeurs d'ions, sur la concentration du

  3. Récupération du platine contenu dans les piles à combustible basse température par voie hydrométallurgique Platinum Recovery from used PEMFC by hydrometallurgy

    Directory of Open Access Journals (Sweden)

    Vincent Denis

    2013-11-01

    Full Text Available La récupération du platine contenu dans la couche catalytique des piles à combustible est nécessaire pour viabiliser cette technologie vers le secteur industriel. Dans cette étude la voie purement hydrométallurgique a été privilégiée au procédé de récupération pyrométallurgique, évitant la destruction des autres constituants de la pile (membrane, … et limitant la formation de gaz toxique. Le procédé mise en œuvre est constitué d'une étape de lixiviation à partir d'un mélange HCl/HNO3, suivie par la précipitation d'un sel de platine (NH42PtCl6 pouvant soit servir à la synthèse d'un nouveau catalyseur soit à l'obtention de platine métallique. Sur l'ensemble de la chaîne un rendement de récupération de plus de 80 % a pu être obtenu mettant en avant le potentiel de cette stratégie. The recovery of platinum in the catalyst layers of PEMFCs (proton exchange membrane fuel cells is required to allow a transfer in industry. In this study, hydrometallurgical route was preferred to pyrometallurgical process, reducing both the destruction of the other components of the cell (membrane, … and the formation of hazardous gas. In this work, the process includes a leaching step from a diluted aqua regia solution, followed by a precipitation step of platinum under the (NH42PtCl6 form. This salt can be used either for the synthesis of a new catalyst or to obtain a metallic platinum. Considering these steps the recovery efficiency has been found to be over 80 %, which bring out the potential of this strategy.

  4. Polarization (ellipsometric) measurements of liquid condensate deposition and evaporation rates and dew points in flowing salt/ash-containing combustion gases

    Science.gov (United States)

    Seshadri, K.; Rosner, D. E.

    1985-01-01

    An application of an optical polarization technique in a combustion environment is demonstrated by following, in real-time, growth rates of boric oxide condensate on heated platinum ribbons exposed to seeded propane-air combustion gases. The results obtained agree with the results of earlier interference measurements and also with theoretical chemical vapor deposition predictions. In comparison with the interference method, the polarization technique places less stringent requirements on surface quality, which may justify the added optical components needed for such measurements.

  5. Study of the tributyl phosphate - 30% dodecane solvent; Etude du solvant phosphate tributylique - 30 % dodecane

    Energy Technology Data Exchange (ETDEWEB)

    Leroy, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses. Centre d' Etudes Nucleaires, 92 (France)

    1967-07-01

    This study, originating mainly from a literature survey, gives the principal chemical and physical features of the tributyl-phosphate (TBP) agent diluted at 30 volumes per cent in dodecane. The mixture is a very commonly used extractant in nuclear fuel processing. In this paper, the main following points are reported: -) the components (TBP and diluents) -) the TBP-diluents systems (non-loaded), -) the TBP-diluents-water systems, -) TBP-diluents-water-nitric acid systems, and -) industrial solvents. (author) [French] Cette etude, d'origine bibliographique, regroupe les caracteristiques physico-chimiques essentielles du phosphate tributylique (TBP) dilue a 30% en volume dans du dodecane. Ce melange constitue un agent d'extraction tres utilise dans le traitement des combustibles nucleaires. Les principaux points traites sont les suivants: -) les constituants (TBP et diluants), -) les systemes TBP-diluants non charges, -) les systemes TBP-diluants-eau, -) les systemes TBP-diluants-eau-acide nitrique, et -) les solvants industriels. (auteur)

  6. Bitumen coating of the radio-active sludges from the effluent treatment plant at the Marcoule centre. Review of the progress reports 1, 2, 3 and 4 (1963); Enrobage par le bitume des boues radioactives de la station de traitement des effluents du centre de Marcoule. Mise au point des etats d'avancement 1, 2, 3 et 4. (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Rodier, J.; Lefillatre, G.; Scheidhauer, J. [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1963-07-01

    Besides the very high activity liquids containing fission products, the chemical treatment of irradiated fuels produces a large volume of aqueous effluents and solid waste of relatively low radioactivity. These weakly active products can be eliminated in the ground, in a hydrographic land system or in the sea. Techniques of evaporation, of resin concentration, and of coprecipitation give rise to inorganic sludges with a high water content. All these residues occupy a large volume and represent a far from negligible weight. In the case of the sludge, their relative fluidity necessitates a conditioning guaranteeing safe storage. The solution to the problem will consist in passing directly from a liquid or a suspension, to a solid whose structure is homogeneous and whose matter is inert with respect to the storage medium (soil, sea, etc. ). We have proposed to coat the radioactive products with bitumen. This article is designed to give a review of the studies undertaken on this method. It consists of a progress report rather than a final assessment. (authors) [French] En dehors des liquides de tres haute activite contenant des produits de fission, le traitement chimique des combustibles irradies produit un volume important d'effluents aqueux et de residus solides de radioactivite relativement faible. Ces produits, faiblement actifs, peuvent etre elimines dans le sol, dans un systeme hydrographique terrestre ou dans la mer. Les techniques d'evaporation, de concentration sur resine, de coprecipitation, permettent la decontamination prealable des liquides. La coprecipitation donne naissance a des boues minerales dont la teneur en eau est elevee. Tous ces residus occupent un volume important et representent un poids non negligeable. Dans le cas des boues, leur fluidite relative exige un conditionnement donnant toutes garanties de securite au stockage. La solution du probleme consistera a passer directement d'un liquide ou d'une suspension a un solide

  7. Bitumen coating of the radio-active sludges from the effluent treatment plant at the Marcoule centre. Review of the progress reports 1, 2, 3 and 4 (1963); Enrobage par le bitume des boues radioactives de la station de traitement des effluents du centre de Marcoule. Mise au point des etats d'avancement 1, 2, 3 et 4. (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Rodier, J; Lefillatre, G; Scheidhauer, J [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1963-07-01

    Besides the very high activity liquids containing fission products, the chemical treatment of irradiated fuels produces a large volume of aqueous effluents and solid waste of relatively low radioactivity. These weakly active products can be eliminated in the ground, in a hydrographic land system or in the sea. Techniques of evaporation, of resin concentration, and of coprecipitation give rise to inorganic sludges with a high water content. All these residues occupy a large volume and represent a far from negligible weight. In the case of the sludge, their relative fluidity necessitates a conditioning guaranteeing safe storage. The solution to the problem will consist in passing directly from a liquid or a suspension, to a solid whose structure is homogeneous and whose matter is inert with respect to the storage medium (soil, sea, etc. ). We have proposed to coat the radioactive products with bitumen. This article is designed to give a review of the studies undertaken on this method. It consists of a progress report rather than a final assessment. (authors) [French] En dehors des liquides de tres haute activite contenant des produits de fission, le traitement chimique des combustibles irradies produit un volume important d'effluents aqueux et de residus solides de radioactivite relativement faible. Ces produits, faiblement actifs, peuvent etre elimines dans le sol, dans un systeme hydrographique terrestre ou dans la mer. Les techniques d'evaporation, de concentration sur resine, de coprecipitation, permettent la decontamination prealable des liquides. La coprecipitation donne naissance a des boues minerales dont la teneur en eau est elevee. Tous ces residus occupent un volume important et representent un poids non negligeable. Dans le cas des boues, leur fluidite relative exige un conditionnement donnant toutes garanties de securite au stockage. La solution du probleme consistera a passer directement d'un liquide ou d'une suspension a un solide dont la structure

  8. Mise au point du rheometre a cisaillement annulaire pour l'etude de rheologie d'un mastic bitumineux avec verre incorpore =

    Science.gov (United States)

    El Mansouri, Souleimane

    Dans le domaine viscoelastique lineaire (VEL, domaine des petites deformations), le comportement thermomecanique du bitume et du mastic bitumineux (melange uniforme de bitume et de fillers) a ete caracterise au Laboratoire des Chaussees et Materiaux Bitumineux (LCMB) de l'Ecole de technologie superieure (ETS) avec l'appui de nos partenaires externes : la Societe des Alcools du Quebec (SAQ) et Eco Entreprises Quebec (EEQ). Les proprietes rheologiques des bitumes et des mastics ont ete mesurees grâce a un nouvel outil d'investigation appele, Rheometre a Cisaillement Annulaire (RCA), sous differentes conditions de chargement. Cet appareil permet non seulement de solliciter des eprouvettes de tailles importantes par rapport a celles utilisees lors des essais classiques, mais aussi d'effectuer des essais en conditions quasi-homogenes, ce qui permet de donner acces a la loi de comportement des materiaux. Les essais sont realises sur une large gamme de temperatures et de frequences (de -15 °C a 45°C et de 0,03Hz a 10 Hz). Cette etude a ete menee principalement pour comparer le comportement d'un bitume avec celui d'un mastic bitumineux dans le domaine des petites deformations. neanmoins, dans une seconde perspective, on s'interesse a l'influence des fillers de verre de post-consommation sur le comportement d'un mastic a faibles niveaux de deformations en comparant l'evolution des modules complexes de cisaillements (G*) d'un mastic avec fillers de verre et un mastic avec fillers conventionnels (calcaire). Enfin, le modele analogique 2S2P1D est utilise pour simuler le comportement viscoelastique lineaire des bitumes et des mastics bitumineux testes lors de la campagne experimentale.

  9. Analyse de la dynamique non-linéaire et du contrôle des instabilités de combustion fondée sur la "Flame Describing Function" (FDF)

    OpenAIRE

    Boudy , Frédéric

    2012-01-01

    This thesis is concerned with an investigation of combustion instabilities in premixed combustors. This problem has been the subject of a continuous effort in relation with the many issues encountered in practical systems like those used in propulsion and energy production. Combustion instabilities usually arise from the coupling between combustion and acoustic eigenmodes of the system. In most cases such resonances lead to vibrations, structural fatigue and intensified heat fluxes to the cha...

  10. The Application of Various Nondestructive Testing Methods to Fuel Elements of the Orgel Type; Application des Differentes Methodes d'Essais Non Destructifs aux Elements Combustibles du Type Orgel; Primenenie razlichnykh nedestruktivnykh metodov ispytanij k toplivnym ehlementam tipa ''orgel''; Aplicacion de Distintos Metodos de Ensayo No Destructivo a los Elementos Combustibles de Tipo Orgel

    Energy Technology Data Exchange (ETDEWEB)

    Bonnet, P.; Jansen, J. [EURATOM, C.C.R., Ispra (Italy)

    1965-09-15

    . There is a device making it possible to examine four or six fuel elements simultaneously, or two or three separately. Standard radiographic tests. Particular stress is laid on the study of welds, and the limits of the experimental conditions in order to obtain good definition are given. In conclusion, the authors present a plan for a semi-industrial inspection system, describing the various possibilities for treatment, and try to define a general policy of non-destructive tests applied to fuel elements. (author) [French] Le memoire presente les differentes methodes employees pour la detection des defauts dans les tubes de gaine des elements combustibles (defauts de type dimensionnel ou defauts structuraux). Les auteurs evoquent egalement les tests finaux sur elements combustibles complets, en particulier: radiographie des soudures et tests d'etanchete. Ce sujet a deja ete partiellement traite. La recherche des caracteristiques dimensionnelles sur tube de gaine lisse en poudre d'aluminium frittee (SAP) a fait l'objet de recherches assez poussees. En particulier: 1. Mesures des diametres internes et externes par utilisation de capteurs pneumatiques et enregistrement des resultats; 2. Mesures des epaisseurs par utilisation, soit des ultrasons en methode de resonance, soit des rayons y (contrat EURATOM - Istituto Sperimentale Metalli Leggeri); 3. Controle de la fleche; 4. Tests sur tubes a ailettes. La detection des defauts sur tube de gaine lisse a egalement fait l'objet de travaux et un critere de rejet a ete adopte suivant l'utilisation future des tubes de gaines. a) La creation de defauts artificiels en fonction de la nocivite des defauts reels dans la poudre d'aluminium frittee est expliquee dans le memoire. Cette etude a montre, en effet, une grande sensibilite aux defauts du type longitudinal crees generalement lors de la transformation par de grosses inclusions. b) Tests par ultrasons. Defauts longitudinaux: Une comparaison entre la methode a deux capteurs et la

  11. Tunnel diode amplifiers and their background noise as a function of the polarization point, the temperature, and the bandwidth; Amplificateurs a diode tunnel et leur bruit de fond, en fonction du point de polarisation, de la temperature et de la bande passante

    Energy Technology Data Exchange (ETDEWEB)

    Ozveaminian, K [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    The author presents mathematical and graphical methods for the study of the stability of tunnel diode circuits. He gives an application to the realization of three amplifiers. Then he describes a theoretical and experimental investigation of the noise of these amplifiers and of its variations with the bias, the temperature and the bandwidth. (author) [French] L'auteur presente deux methodes, l'une theorique l'autre graphique, pour l'etude de la stabilite des circuits a diode tunnel, dont il fait une application a la realisation de trois amplificateurs. Il effectue ensuite une etude theorique et experimentale du bruit de fond de ces amplificateurs, en fonction du point de polarisation, de la temperature et de la bande passante. (auteur)

  12. Combustion engineering

    CERN Document Server

    Ragland, Kenneth W

    2011-01-01

    Introduction to Combustion Engineering The Nature of Combustion Combustion Emissions Global Climate Change Sustainability World Energy Production Structure of the Book   Section I: Basic Concepts Fuels Gaseous Fuels Liquid Fuels Solid Fuels Problems Thermodynamics of Combustion Review of First Law Concepts Properties of Mixtures Combustion StoichiometryChemical EnergyChemical EquilibriumAdiabatic Flame TemperatureChemical Kinetics of CombustionElementary ReactionsChain ReactionsGlobal ReactionsNitric Oxide KineticsReactions at a Solid SurfaceProblemsReferences  Section II: Combustion of Gaseous and Vaporized FuelsFlamesLaminar Premixed FlamesLaminar Flame TheoryTurbulent Premixed FlamesExplosion LimitsDiffusion FlamesGas-Fired Furnaces and BoilersEnergy Balance and EfficiencyFuel SubstitutionResidential Gas BurnersIndustrial Gas BurnersUtility Gas BurnersLow Swirl Gas BurnersPremixed-Charge Engine CombustionIntroduction to the Spark Ignition EngineEngine EfficiencyOne-Zone Model of Combustion in a Piston-...

  13. Aux origines du monde

    CERN Multimedia

    2004-01-01

    "C'est l'histoire d'une aventure humaine, scientifique, international qui a vu le jour il y a cinquante ans, aux confins de la Suisse et du département de l'Ain. Le plus grand laboratoire de physique des particules du monde, le Cern, a été fondé en 1954. Les festivités organisées à l occasion de cet anniversaire connaîtront leur point d'orgue le 16 octobre prochain, avec portes-ouvertes, accueil de personallités et inauguration d'un monumnet spécifique, le Globe de l'innovation" (2 pages)

  14. Development of reduced kinetic schemes for the description of pollutants formation in combustion; Mise au point de schemas cinetiques reduits pour decrire la formation des polluants dans la combustion

    Energy Technology Data Exchange (ETDEWEB)

    Ferrendier, M.

    1998-12-17

    The typical dimensions of details chemical-kinetic mechanisms proposed to describe combustion systems are too large for multi-dimensional computations applications. The objective of reduction methods is to construct low-dimensional schemes that can be incorporated in industrial codes. We consider here a new class of methods based on a mathematical analysis of the detailed chemical-kinetic mechanisms, and the identification of a low-dimensional manifold that describes the slow dynamics of the chemical system. The mathematical reduction methods considered in this work are the Intrinsic Low Dimensional Manifold (ILDM) method proposed by Maas and Pope (1992), and the Singular Perturbation (PS) method proposed by Duchene and Rouchon (1996). The domain of validity of the ILDM or PS reduced schemes is limited to a high temperature domain T {>=} T{sub c}. This result suggests that ignition is out of the domain of application of reduced mechanisms. In the case of a CO/H{sub 2}/N{sub 2}-air combustion system, and using a two-dimensional slow manifold, we find T{sub c} {approx} 750 K. We also find that for that particular system, 2 progress variables are sufficient for an accurate description of the structure and the velocity of a laminar premixed flame. In the case of a CH{sub 4}-air combustion system, and using a two-dimensional slow manifold, we find T{sub c}{approx}1500 K. We also find that 2 progress variables are insufficient for an accurate description of the structure and the velocity of a laminar premixed flame. The study of the different NO formation mechanisms show that the thermal NO mechanism (the Zeldovich mechanism) is dominant for premixed configurations with lean or stoichiometric conditions ({phi}){>=}1.2), and for non-premixed configurations at high temperatures and high pressures (T{sub air}{>=}1000 K, P {>=} 10 bars). Under these conditions, the MPKIVA sub model used to describe NO formation in the IFP version of the KIVA code performs reasonably well. An

  15. 3d Modeling of Combustion for Di-Si Engines Modélisation 3D de la combustion dans les moteurs à injection directe d'essence

    Directory of Open Access Journals (Sweden)

    Duclos J. P.

    2006-12-01

    Full Text Available Direct injection of gasoline is a promising concept to reduce fuel consumption of SI engines. The development of GDI engines is difficult and 3D CFD is a way to support its design. It requires models able to describe the spray and its evaporation and combustion. This paper presents a model, the ECFM, that enables to compute combustion for stratified load in the GDI engines. This model is a development of the Coherent Flame Model which includes thermal expansion effects, and is coupled with a burnt/unburnt gases conditionnal thermodynamic properties description. The model is validated by comparing measurements and computations on the GDI Mitsubishi engine in production. L'injection directe d'essence (IDE est un concept prometteur pour les moteurs à allumage commandé. La mise au point de ce type de moteur est néanmoins délicate, et le calcul 3D des chambres de combustion est un moyen d'aider à leur conception. Ceci nécessite cependant de disposer de modèles adaptés, à même de décrire le jet d'essence, son évaporation et la combustion du mélange créé. Cet article présente un modèle ECFM de simulation de la combustion dans les moteurs IDE, y compris en fonctionnement stratifié. C'est un développement du modèle flamme cohérente qui comprend des effets d'expansion thermique et est couplé avec une description conditionnelle gaz frais/gaz brûlés des grandeurs thermodynamiques. Ce modèle a été validé par rapprochement de mesures et simulations sur le moteur GDI Mitsubishi.

  16. Plutonium, nuclear fuel; Le plutonium, combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Grison, E [Commissariat a l' Energie Atomique, Fontenay aux Roses (France). Centre d' Etudes Nucleaires, Saclay

    1960-07-01

    A review of the physical properties of metallic plutonium, its preparation, and the alloys which it forms with the main nuclear metals. Appreciation of its future as a nuclear fuel. (author) [French] Apercu sur les proprietes physiques du plutonium metallique, sa preparation, ses alliages avec les principaux metaux nucleaires. Consideration sur son avenir en tant que combustible nucleaire. (auteur)

  17. Techniques de combustion Combustin Techniques

    Directory of Open Access Journals (Sweden)

    Perthuis E.

    2006-11-01

    Full Text Available L'efficacité d'un processus de chauffage par flamme est étroitement liée à la maîtrise des techniques de combustion. Le brûleur, organe essentiel de l'équipement de chauffe, doit d'une part assurer une combustion complète pour utiliser au mieux l'énergie potentielle du combustible et, d'autre part, provoquer dans le foyer les conditions aérodynamiques les plus propices oux transferts de chaleur. En s'appuyant sur les études expérimentales effectuées à la Fondation de Recherches Internationales sur les Flammes (FRIF, au Groupe d'Étude des Flammes de Gaz Naturel (GEFGN et à l'Institut Français du Pétrole (IFP et sur des réalisations industrielles, on présente les propriétés essentielles des flammes de diffusion aux combustibles liquides et gazeux obtenues avec ou sans mise en rotation des fluides, et leurs répercussions sur les transferts thermiques. La recherche des températures de combustion élevées conduit à envisager la marche à excès d'air réduit, le réchauffage de l'air ou son enrichissement à l'oxygène. Par quelques exemples, on évoque l'influence de ces paramètres d'exploitation sur l'économie possible en combustible. The efficiency of a flame heating process is closely linked ta the mastery of, combustion techniques. The burner, an essential element in any heating equipment, must provide complete combustion sa as to make optimum use of the potential energy in the fuel while, at the same time, creating the most suitable conditions for heat transfers in the combustion chamber. On the basis of experimental research performed by FRIF, GEFGN and IFP and of industrial achievements, this article describesthe essential properties of diffusion flames fed by liquid and gaseous fuels and produced with or without fluid swirling, and the effects of such flames on heat transfers. The search for high combustion temperatures means that consideration must be given to operating with reduced excess air, heating the air or

  18. Machine for checking the radioactive contamination of clothing (1961); Machine a controler le linge du point de vue de sa contamination radioactive (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Mimaud, R; Cottignies, S [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1961-07-01

    This machine is designed to check working clothes after decontamination treatment. It checks automatically for {alpha} and {beta} {gamma} The clothing is carried on a moving belt under a rack of Geiger-Muller counters followed by zinc sulphide scintillators linked to photomultipliers. During its passage under these probes two separate counting systems count the {beta} {gamma} and the {alpha} activities. If a certain fixed rate is reached, a basket reserved for contaminated linen moves into position in front of the belt to collect the clothing; if this rate is not attained the linen is collected in another basket. The starting and stopping of counting, and the return to zero, are controlled by means of 3 photoelectric cells which detect the arrival of the clothing before and after scanning, and its delivery into the baskets. (authors) [French] Cette machine est destinee a controler les vetements de travail apres le traitement de decontamination. Elle effectue automatiquement un controle en {alpha} et en {beta} {gamma}. Le linge entraine par un tapis roulant passe sous une rampe de compteurs Geiger-Muller puis sous des scintillateurs au sulfure de zinc associes a des photomultiplicateurs. Pendant son passage sous ces sondes, deux chaines de comptage distinctes comptent l'activite {beta} {gamma} et l'activite {alpha}. Si un certain taux fixe est atteint, un panier reserve au linge contamine se positionne devant le tapis pour recueillir le linge; dans le cas contraire, le linge est recueilli dans un autre panier. Les operations de debut de comptage, arret de comptage et remise a zero de l'ensemble sont commandees a l'aide de 3 cellules photoelectriques qui detectent l'arrivee du linge avant et apres les sondes, ainsi que sa retombee dans les paniers. (auteurs)

  19. Points cardinaux pour la conception de formations universitaires pluridisciplinaires en épistémologie et histoire des sciences pour les enseignants du secondaire, ou comment s'appuyer sur des dilemmes

    Directory of Open Access Journals (Sweden)

    Bernard Alain

    2014-01-01

    Full Text Available Cet article s'intéresse à quelques uns des problèmes qui sous-tendent la conception des formations en épistémologie et histoire des sciences aujourd'hui offertes en France aux enseignants du second degré, en réponse à la demande croissante qui leur est faite. Ayant relevé plusieurs points communs incontournables à toute entreprise de formation universitaire s'adressant à ce type de public, notre objet principal est de proposer quelques points cardinaux, c'est-à-dire quelques principes d'orientation permettant de guider la conception de ce type de formation, pour autant qu'il entende concilier les exigences de pertinence, c'est-à-dire d'être adapté au public visé, et de rester ancré dans la recherche universitaire. Concernant le problème de la pertinence des formations, nous proposons préalablement deux points de vue complémentaires pour cerner ces contraintes: (1 le premier s'intéresse aux structures institutionnelles ainsi qu'aux sources disponibles qui conditionnent le travail des enseignants ; (2 le second se concentre sur l'activité des enseignants et résume les principaux dilemmes professionnels qu'ils doivent affronter alors qu'ils investissent au cœur de leur enseignement un champ interdisciplinaire comme l'est l'histoire et l'épistémologie des sciences. (3 Ce double point de vue nous permet alors de proposer un ensemble de points cardinaux pour la conception de formations universitaires permettant aux enseignants ou futurs enseignants de développer leur pouvoir d'agir dans ce domaine.

  20. The distribution, atmospheric transfer, and assessment of krypton-85; Distribution, transfert atmospherique et bilan du krypton-85

    Energy Technology Data Exchange (ETDEWEB)

    Pannetier, R [Commissariat a l' Energie Atomique, 92 - Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-06-01

    Techniques for sampling and measuring krypton-85 have been developed which allowed to determine its geographical distribution. From its use as a tracer, an evaluation of the air masses which cross over the subtropical fronts has been derived. Besides, the stratospheric character of air pollution by krypton-85 at the level of the antarctic soil has been shown out. Levels of krypton-85 seem to point out to an underestimation of the assessment of nuclear explosion fission energies as adopted by the United Nations Scientific committee on the effects of atomic radiation and emphasize the need to set limits as soon as possible to the amounts of krypton-85 released to the atmosphere by fuel-reprocessing plants. (author) [French] La mise au point de techniques de prelevement et de mesure du krypton-85 atmospherique a permis de determiner sa repartition geographique. De son utilisation comme traceur on deduit une evaluation des masses d'air qui traversent les fronts subtropicaux. Par ailleurs, le caractere stratospherique de la pollution de l'air par le krypton-85 au niveau du sol antarctique est mis en evidence. Le bilan du krypton-85 semble reveler une sous-estimation du bilan des energies de fission des explosions adopte par le Comite scientifique des Nations Unies et souligne la necessite de limiter des que possible les quantites de krypton-85 rejetees dans l'atmosphere par les usines de traitement de combustibles irradies. (auteur)

  1. Burn up physics; Physique des combustibles irradies

    Energy Technology Data Exchange (ETDEWEB)

    Tretiakoff, O [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    requires samples of the order of several kilograms only. The relationships between these measurements and the investigations of lattices are discussed, and an outline is given of the way of carrying out the systematic study of fuels of various compositions. The method has been successfully applied to the systematic study of irradiated fuels (analysed independently by the methods mentioned above) thus giving the possibility of measuring in situ the absorption of fission products. (author) [French] Cette communication expose un ensemble d'etudes theoriques et d'experiences, effectuees au CEA et destinees a faire progresser la connaissance de l'evolution de la reactivite (au cours de l'irradiation du combustible) dans les reacteurs a uranium naturel ou faiblement enrichi.,. On rappelle les difficultes de l'experimentation directe sur des masses importantes de combustible irradie - en particulier dans les reacteurs de puissance en fonctionnement - et on souligne la necessite d'experiences a caractere fondamental distinguant: d'une part l'evolution de la composition des combustibles (chaines de noyaux lourds, produits de fission), d'autre part l'effet des modifications de composition sur le bilan de neutrons. Avant de presenter trois categories d'experiences que l'on est conduit a entreprendre, on rappelle l'importance des problemes lies aux spectres de neutrons et on decrit rapidement les methodes pratiques de calcul utilisees. L'irradiation systematique de quelques types de combustibles, suivie de leur analyse chimique et isotopique est en cours depuis plusieurs annees. On donne un apercu de l'ensemble du programme experimental et on decrit les moyens et les methodes mis en oeuvre: chaine {alpha}, {beta}, {gamma} pour la preparation des echantillons, dosage du Plutonium par coulommetrie et double dilution isotopique, separation du Bore utilise dans certains cas pour la mesure des densites de neutrons integrees. On discute sur quelques exemples l'interpretation des mesures

  2. Combustion physics

    Science.gov (United States)

    Jones, A. R.

    1985-11-01

    Over 90% of our energy comes from combustion. By the year 2000 the figure will still be 80%, even allowing for nuclear and alternative energy sources. There are many familiar examples of combustion use, both domestic and industrial. These range from the Bunsen burner to large flares, from small combustion chambers, such as those in car engines, to industrial furnaces for steel manufacture or the generation of megawatts of electricity. There are also fires and explosions. The bountiful energy release from combustion, however, brings its problems, prominent among which are diminishing fuel resources and pollution. Combustion science is directed towards finding ways of improving efficiency and reducing pollution. One may ask, since combustion is a chemical reaction, why physics is involved: the answer is in three parts. First, chemicals cannot react unless they come together. In most flames the fuel and air are initially separate. The chemical reaction in the gas phase is very fast compared with the rate of mixing. Thus, once the fuel and air are mixed the reaction can be considered to occur instantaneously and fluid mechanics limits the rate of burning. Secondly, thermodynamics and heat transfer determine the thermal properties of the combustion products. Heat transfer also plays a role by preheating the reactants and is essential to extracting useful work. Fluid mechanics is relevant if work is to be performed directly, as in a turbine. Finally, physical methods, including electric probes, acoustics, optics, spectroscopy and pyrometry, are used to examine flames. The article is concerned mainly with how physics is used to improve the efficiency of combustion.

  3. Development of flameless combustion; Desarrollo de la combustion sin flama

    Energy Technology Data Exchange (ETDEWEB)

    Flores Sauceda, M. Leonardo; Cervantes de Gortari, Jaime Gonzalo [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)]. E-mail: 8344afc@prodigy.net.mx; jgonzalo@servidor.unam.mx

    2010-11-15

    The paper intends contribute to global warming mitigation joint effort that develops technologies to capture the CO{sub 2} produced by fossil fuels combustion and to reduce emission of other greenhouse gases like the NO{sub x}. After reviewing existing combustion bibliography is pointed out that (a) touches only partial aspects of the collective system composed by Combustion-Heat transfer process-Environment, whose interactions are our primary interest and (b) most specialists think there is not yet a clearly winning technology for CO{sub 2} capture and storage. In this paper the study of combustion is focused as integrated in the aforementioned collective system where application of flameless combustion, using oxidant preheated in heat regenerators and fluent gas recirculation into combustion chamber plus appropriated heat and mass balances, simultaneously results in energy saving and environmental impact reduction. [Spanish] El trabajo pretende contribuir al esfuerzo conjunto de mitigacion del calentamiento global que aporta tecnologias para capturar el CO{sub 2} producido por la combustion de combustibles fosiles y para disminuir la emision de otros gases invernadero como NOx. De revision bibliografica sobre combustion se concluye que (a) trata aspectos parciales del sistema compuesto por combustion-proceso de trasferencia de calor-ambiente, cuyas interacciones son nuestro principal interes (b) la mayoria de especialistas considera no hay todavia una tecnologia claramente superior a las demas para captura y almacenaje de CO{sub 2}. Se estudia la combustion como parte integrante del mencionado sistema conjunto, donde la aplicacion de combustion sin flama, empleando oxidante precalentado mediante regeneradores de calor y recirculacion de gases efluentes ademas de los balances de masa y energia adecuados, permite tener simultaneamente ahorros energeticos e impacto ambiental reducido.

  4. Technical Developments in the USAEC Process Radiation Development Program; Etudes technologiques dans le cadre du programme de mise au point d'applications industrielles des rayonnements de la CEA-EU; Issledovaniya v oblasti promyshlennogo primeneniya izluchenij, vkhodyashchie v programmu komissii po atomnoj ehnergii USAEC; Progresos tecnicos en el programa de la USAEC para el fomento de la irradiacion industrial

    Energy Technology Data Exchange (ETDEWEB)

    Machurek, J. E.; Stein, M. H. [Division of Isotopes Development, USAEC, Washington, DC (United States)

    1963-11-15

    A broad range of researches have been undertaken in the USAEC 'Process radiation development program'. The primary objective of these studies is to foster development of technology leading to the productive industrial use of ionizing radiation. Results of fourteen of these investigations are reported.some in outline in this paper and some in detail in these Proceedings. The subjects included are researches on: (1) Preparation of wood-plastic combinations using gamma radiation to induce polymerization. (2) Use of fission-product beta radiation for the hydrogenation of coal and coal products to produce liquid hydrocarbon fuels. (3) Production of semi-conductor devices with the formation of predetermined spacial distribution impurity patterns via neutron transmutation doping. (4) Radiation-induced polymerization of ethylene and copolymers. (5) Basic studies in radiation-induced reaction mechanisms and kinetics. (6) Radiation chemistry involved in the fluorination of various aromatic compounds. (7) Use of polyfunctional monomers for enhanced radiation cross-linking of polyethylene, polypropylene, polyisobutylene and cellulose acetate. (8) Effect of swelling, strain and temperature on the physical and chemical properties of radiation produced polymers. (9) Radiation-induced changes in polymers leading to graft copolymerization as influenced by structural factors. (10) The utilization of nuclear radiation for the modification of textile materials. (11) Radiation-induced reactions utilizing krypton-85. (12) The preparation of a ''Radiation Handbook''. (13) Use of the organometallic bond in high level gamma radiation dosimetry. (14) The development of a solar cell dosimeter. (author) [French] Des recherches tres diverses ont ete entreprises dans le cadre du programme de mise au point d'applications industrielles des rayonnements execute par la CEA-EU. Ce programme a pour but essentiel de favoriser le developpement de la technologie en vue d'un emploi industriel productif

  5. Contribution to the study on the flow rate adjustment for gas cooled power reactors (1964); Contributiom a l'etude de reglage du debit pour les reacteurs industriels refroidis par gaz (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Milliot, B. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1961-06-15

    1. This original study firstly defines the problem of the adjustment of the coolant flow rate in a reactor channel as a function of the corresponding heat transfer equations and of the local and temporal neutron flux. The necessity of such an adjustment is pointed out and the modifying parameters are studied. An adjustment study using the envelope of the possible flux curves is developed. A short study on the technology and the economical advantage of this adjustment is presented. Some measurements, made on G-1 and G-2, show the precision one can obtain from adjustment apparatus itself as well as from the complete reactor adjustment system. 2. Evolution of nuclear properties of fuel in an heterogeneous thermal reactor. In the first port of this paper, the phenomena of fuel evolution have been mainly pointed out. Now a bibliographical study more qualitatively than quantitatively has been done. This survey specifies the present theories and relates to a real effective cross section and also yields to the bases of such a nuclear calculation. (author) [French] 1. Cette etude originale definit d'abord le probleme du reglage du debit de refrigerant dans un canal de reacteur en fonction de la formulation du calcul des performances thermodynamiques de ce canal et des variations du flux neutronique dans l'espace et le temps. La necessite du reglage est ensuite mise en evidence et les parametres le modifiant sont etudies. Une methode de reglage, basee sur l'emploi d 'une courbe enveloppe des courbes de flux possibles, est donnee. Une breve etude de la technologie et des incidences economiques du reglage est presentee. Des mesures effectuees sur les reacteurs G-1 et G-2 montrent la precision que l'on peut attendre des dispositifs de reglage comme du reglage d'ensemble du reacteur lui-meme. 2. Evolution des proprietes nucleaires du combustible dans un reacteur heterogene a neutrons thermiques. Les phenomenes d'evolution du combustible

  6. Contribution to the study on the flow rate adjustment for gas cooled power reactors (1964); Contributiom a l'etude de reglage du debit pour les reacteurs industriels refroidis par gaz (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Milliot, B [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1961-06-15

    1. This original study firstly defines the problem of the adjustment of the coolant flow rate in a reactor channel as a function of the corresponding heat transfer equations and of the local and temporal neutron flux. The necessity of such an adjustment is pointed out and the modifying parameters are studied. An adjustment study using the envelope of the possible flux curves is developed. A short study on the technology and the economical advantage of this adjustment is presented. Some measurements, made on G-1 and G-2, show the precision one can obtain from adjustment apparatus itself as well as from the complete reactor adjustment system. 2. Evolution of nuclear properties of fuel in an heterogeneous thermal reactor. In the first port of this paper, the phenomena of fuel evolution have been mainly pointed out. Now a bibliographical study more qualitatively than quantitatively has been done. This survey specifies the present theories and relates to a real effective cross section and also yields to the bases of such a nuclear calculation. (author) [French] 1. Cette etude originale definit d'abord le probleme du reglage du debit de refrigerant dans un canal de reacteur en fonction de la formulation du calcul des performances thermodynamiques de ce canal et des variations du flux neutronique dans l'espace et le temps. La necessite du reglage est ensuite mise en evidence et les parametres le modifiant sont etudies. Une methode de reglage, basee sur l'emploi d 'une courbe enveloppe des courbes de flux possibles, est donnee. Une breve etude de la technologie et des incidences economiques du reglage est presentee. Des mesures effectuees sur les reacteurs G-1 et G-2 montrent la precision que l'on peut attendre des dispositifs de reglage comme du reglage d'ensemble du reacteur lui-meme. 2. Evolution des proprietes nucleaires du combustible dans un reacteur heterogene a neutrons thermiques. Les phenomenes d'evolution du combustible tiennent une place importante dans l

  7. Design of the Small Rods Forming the Fuel Element of the First Charge of the EL4 Reactor. Cladding Problems; Etude des crayons constituant l'element combustible du premier jeu d'EL4 - probleme de la gaine; Problema pokrytiya nebol'shikh steeknej, obrazushchikh toplivnyj ehlement pervoj zagruzki reaktora EL.4; Estudio de las barras que constituyen los elementos combustibles de la primera carga del reactor EL4 - el problema de las vainas

    Energy Technology Data Exchange (ETDEWEB)

    Bailly, H.; Ringot, C.; Weisz, M. [Centre d' Etudes Nucleaires de Saclay (France)

    1963-11-15

    The fuel element for the first charge of EL4 makes use of stainless steel cans. The grade of steel chosen and the can thickness depend on the corrosion resistance and mechanical strength required. The operating stresses and temperatures are such that fabrication of a can lasting throughout the life of the fuel element calls for a highly resistant grade of steel, of thickness greater than 0.5 mm. When the can bears on the fuel as a result of creep, deformation in diametrical clearance may lead to ovalization and folding, while deformation in longitudinal clearance may cause buckling of the can. Numerous tests have been carried out on cans of thickness 0.3 and 0.4 mm to determine type of deformation as a function of clearance. To be certain of avoiding ovalization with the thicknesses proposed and to keep the internal temperature of the fuel as low as possible, the clearance must be reduced to zero in fabrication. (author) [French] L'element combustible du premier jeu EL4 utilise des gaines en acier inoxydable. Le choix de la nuance et de l'epaisseur de la gaine est lie a des considerations de tenue a la corrosion et de tenue mecanique. Les contraintes et les temperatures d'utilisation ne permettent pas de concevoir une gaine resistante pendant toute la vie de l'element combustible a moins d'utiliser une nuance tres resistante et d'epaisseur superieure a 0,5 mm. On admet que la gaine s'applique par fluage sur le combustible: la deformation dans les jeux diametraux peut conduire a la formation d'une ovalisation et d'un pli; la deformation dans les jeux longitudinaux peut conduire a des flambages de la gaine. De nombreux essais ont ete realises sur des gaines d'epaisseurs 0,3 et 0,4 mm pour connaitre le mode de deformation en fonction des jeux. Pour etre certain de ne jamais avoir d'ovalisation avec les epaisseurs envisagees, et pour avoir la temperature a coeur du combustible la plus basse possible, on est conduit a reduire a zero le jeu en fabrication. (author

  8. The industrial production of fuel elements; La fabrication en france des elements combustibles

    Energy Technology Data Exchange (ETDEWEB)

    Boussard, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires; Nadal, J [Societe Industrielle de Combustible Nucleaire (SICN), 75 - Paris (France); Pellen, A [Compagnie pour l' Etude et la Realisation de Combustibles Atomiques (CERCA), 75 - Paris (France)

    1964-07-01

    -pool type reactors. The authors show how the problem of the industrial production of rolled fuel elements has been solved in France, and give the three steps involved: 1 - Assembly of the plates made in the U.S.A., 2 - Rolling of the cores made in the U.S.A. to obtain the plates, 3 - Fabrication of the U-Al alloy and production of the cores. They then recall briefly the characteristics of the different fuel elements now in production. A description is given of the various stages of the production including information about the equipment; stress is laid on the extent of the controls carried out at each stage. In conclusion the authors consider the future development of this type of production taking into account the improvements planned and those which are possible. (authors) [French] Les auteurs traitent successivement de la fabrication industrielle des elements combustibles pour reacteurs de puissance de la filiere U naturel graphite-gaz et plus particulierement pour les centrales energetiques d'E.D.F. et de celle des elements combustibles a base d'U enrichi destines aux reacteurs experimentaux du type 'piscine'. 1ere Partie - LES ELEMENTS COMBUSTIBLES AVANCES POUR LES REACTEURS E.D.F.: Apres un bref rappel des caracteristiques des elements combustibles actuellement fabriques industriellement pour les reacteurs de MARCOULE et de CHINON, les auteurs indiquent les differentes etapes suivies pour aboutir au stade de la fabrication industrielle d'un element combustible nouveau, tant en ce qui concerne la gaine et eventuellement la chemise de graphite que le combustible lui-meme. Pour ce qui est de l'elaboration du combustible, ils decrivent les differentes operations en insistant sur les points originaux de la fabrication et de l'appareillage tels que: - coulees en moules chauds, - traitement thermique des alliages U.Mo 1 p. 100, - soudure des pastilles de fermeture des tubes, - gainage - controle aux differents stades. En ce qui concerne la fabrication des gaines, ils

  9. Etude Théorique et Numérique d’une Méthode de Point Intérieur pour la Résolution du Problème d’Inégalités Variationnelles

    Directory of Open Access Journals (Sweden)

    H GRAR

    2007-12-01

    Full Text Available Dans ce travail, nous présentons une nouvelle alternative de type point intérieur pour résoudre le problème d’inégalités variationnelles noté (VIP. Ce dernier connu par son importance grandissante aussi bien sur le plan théorique que pratique, est malheureusement traité par des méthodes non pratiques (hypothèses trop restrictives, calcul pénalisant des projections. L’idée de progresser à l’intérieur du domaine des contraintes est à fait attrayante, car une fois mise au point elle élimine tous les handicapes algorithmiques ou presque. Cette idée est aussi motivée par le succès remarquable des techniques de point intérieur au niveau de la programmation mathématique en général. Nous avons pu mettre en oeuvre plusieurs versions de l’algorithme issues d’une étude théorique approfondie dûe à Censor et al. [1998] et comprenant nos propres aménagements. Au cours de l’implémentation numérique, on a fait intervenir des problèmes mathématiques très importants. Les résultats obtenus sont très encourageants. Ils sont présentés dans un cadre comparatif signifiant.

  10. Study of the combustion of aluminium and magnesium particulates: influence of the composition of the gaseous mixture and of pressure; Etude de la combustion de particules d'aluminium et de magnesium: influence de la composition du melange gazeux et de la pression

    Energy Technology Data Exchange (ETDEWEB)

    Legrand, B.

    2000-07-01

    The combustion of metal particulates has a major interest in the domain of space propulsion. Aluminium is today used as doping material in the solid propellant of Ariane 5 rocket engines. Magnesium represents a possible fuel for propellers allowing a come back from Mars. An electrostatic levitation device has been used to study the combustion in controlled environment of particulates having a size representative of those encountered in propellers. The particulates are ignited with a laser and observed by fast cinematography. The inhibitive property of hydrogen chloride, an important constituent of the propellant atmosphere, on the combustion of aluminium particulates has been evidenced. These results have been compared with those obtained with a kinetic model in gaseous phase. The combustion of magnesium particulates in carbon dioxide has been studied for 53-63 {mu}m and 1-2 mm particulates. It is shown that the ignition of small particulates is controlled by the chemical kinetics and that the limit ignition pressure is reversely proportional to the particulates size. A study on big samples, performed in normal gravity but also in reduced gravity to get rid of the natural convection phenomena, has permitted to show a pulsed combustion regime linked with the presence of heterogenous reactions. The measurement of the combustion durations for the different sizes of particulates has permitted to propose a correlation between these two parameters for the particulate diameters comprised between 50 {mu}m and 2 mm. (J.S.)

  11. Alternatives Sud, “L’offensive des marchés sur l’université. Points de vue du Sud”

    Directory of Open Access Journals (Sweden)

    Jean-Émile Charlier

    2011-03-01

    Full Text Available Un nouvel ordre mondial de l’enseignement supérieur est de toute évidence en gestation, le processus de Bologne en est une manifestation parmi beaucoup d’autres. Les analyses de ce phénomène restent trop rares, l’initiative d’Alternatives Sud arrive donc à point nommé. Le numéro est introduit par N. Hirtt, dont les thèses sur l’influence que la table ronde des industriels (ERT exerce sur l’évolution de nos systèmes éducatifs sont connues. Dans son éditorial fort bien documenté, il dresse le ...

  12. Two further years of operation of the reactor G1 (july 1958 - july 1960); Deux nouvelles annees de fonctionnement du reacteur G1. (juillet 1958 - Juillet 1960)

    Energy Technology Data Exchange (ETDEWEB)

    Mathot, P; Bauzit, J; Cante, R; Hebrard, L [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The aim of the present report is to present certain observations and to give the results obtained during the period from july the 1{sup st} 1958 to july the 1{sup st} 1960. The main operations carried out during this period were, chronologically: - From july the 5{sup th} to october the 18{sup th} 1958: preparation and execution of the first annealing of the graphite. - From dec. the 15{sup th} 1958 to july the 15{sup th} 1959: a discharging campaign which resulted in the complete renewal of the fuel elements. During the monthly stoppages of this campaign, it was possible to make certain observations concerning the packing of the graphite, while at the same time measurements of the temperature of the element cans were made at an increased number of points. - From september the 25{sup th} 1959 to december the 9{sup th} 1959: preparation and execution of the second annealing. At the end of the annealing, the thorium lattice was modified and extra thermocouples were installed for measuring the temperature of the body of the graphite. An apparatus was built for measuring the radial flux. - From december the 9{sup th} 1959 to july 1960: a continuous operation campaign, with a minimum of stoppages. The experimental results are re-assembled, independently of their chronological order, under three main headings which describe the reactors history: - continuous operation, - discharges, - annealing of the reactor. (author) [French] Le but du present rapport est d'exposer certaines observations faites et les resultats obtenus au cours de la periode du 1{sup er} juillet 1958 au 1{sup er} juillet 1960. Cette periode a ete marquee chronologiquement par les operations essentielles suivantes: - du 5 juillet au 18 octobre 1958: preparation et execution du premier recuit du graphite. - du 15 decembre 1958 au 15 juillet 1959: campagne de dechargement entrainant un renouvellement total des cartouches de combustibles. Au cours des arrets mensuels de cette campagne, certaines

  13. Control of the electrical operating point of an electric discharge by mean of its power supply; Controle du point de fonctionnement des decharges electriques par l'intermediaire de leur alimentation

    Energy Technology Data Exchange (ETDEWEB)

    Salanne, J.Ph.

    2005-11-15

    The operating points obtained by the coupling of the power supply with the electric discharge system can be unstable because of the dynamical behaviour of the discharge or because of a change in its length. In this work, the different possible couplings existing between the discharge and the characteristics of its power supply are analyzed in order to optimize the design and control of the power supply and to control the operating point. Analytical and numerical modeling of the system are proposed which allow to simulate the couplings between the power supply and the discharge. This approach is completed by experimental investigations allowing to consider the cases of peak/peak discharges, dielectric barrier discharges (DBD), and gliding arcs. (J.S.)

  14. [Cerebrovascular accidents: risk factors, clinical course and prognosis in the Cardiology "B" Service of the du Point G University Hospital Center, Bamako].

    Science.gov (United States)

    Coulibaly, S; Diakité, S; Diall, I B; Menta, I; Sacko, A K; Diallo, B

    2010-01-01

    Our study of series, futurology, descriptive and analytical proceeded in the service of Cardiology B of the CHU of the Point G of the 1(er) July at 31 Décember 2007 and related to 57 in-patients. It aimed to release the factors of risks, to evaluate under treatment the evolution and to determine the prognostic elements of the cerebral vascular accidents. All the patients hospitalized in the service of Cardiology G for the period of study for cerebral vascular accident documented by a cerebral TDM was included in the series. The cerebral vascular accidents represented more of the quarter (25,22 %) of the admissions. The sample counted 29 women (50,9 %) and 28 men (49,1 %) with a sex ratio of 1,03 in favour of the women. The average age was 61,17 years ± 13,71 there. Arterial hypertension (59,6 %) was the first factor of risk and in the series the ischaemic AVC constituted approximately three quarters (70,2 %) of the organic types. It was especially male and the rather female hemorrhagic lesion. The hemorrhagic AVC was noted before 30 years and the ischaemic AVC beyond. The complications were with female prevalence and identical lethality in the two sexes. The hospital death rate in the study was considerable (10,5 %). The found prognostic elements did not have statistical significance.

  15. The Use of Fuel Gas as Stripping Medium in Atmospheric Distillation of Crude Oil L’utilisation de gaz combustible comme moyen d’extraction des fractions légères en distillation atmosphérique du pétrole brut

    OpenAIRE

    Plellis-Tsaltakis C.; Lygeros A.I.

    2011-01-01

    Stripping of petroleum fractions aims to remove the light ends that spoil some of their properties, such as the flash point. Stripping usually employs steam for that purpose. Except for steam, other substances can perform the same function, among them light hydrocarbons. In this article, we investigate the use of refinery fuel gas as stripping medium for a crude oil atmospheric distillation unit. L’extraction des fractions légères du pétrole vise à enlever les produits nuisibles à cer...

  16. Biofuels combustion.

    Science.gov (United States)

    Westbrook, Charles K

    2013-01-01

    This review describes major features of current research in renewable fuels derived from plants and from fatty acids. Recent and ongoing fundamental studies of biofuel molecular structure, oxidation reactions, and biofuel chemical properties are reviewed, in addition to combustion applications of biofuels in the major types of engines in which biofuels are used. Biofuels and their combustion are compared with combustion features of conventional petroleum-based fuels. Two main classes of biofuels are described, those consisting of small, primarily alcohol, fuels (particularly ethanol, n-butanol, and iso-pentanol) that are used primarily to replace or supplement gasoline and those derived from fatty acids and used primarily to replace or supplement conventional diesel fuels. Research efforts on so-called second- and third-generation biofuels are discussed briefly.

  17. Les caractéristiques de la terminologie des sciences relatives à la famille du point de vue de l’extraction terminologique

    Directory of Open Access Journals (Sweden)

    Ágoston Nagy

    2013-12-01

    Full Text Available Nagy, Á.: The Characteristics of Terminology of Sciences in relation to Family from point of view of Terminological Extraction According to Eugen Wüster, terms are lexical units that belong to a scientific domain where they are connected to a concept that they denote; therefore, terms have to have a precise definition. In the term extraction process, terms can mainly be recognised by morphosyntactic patterns: for example, noun+noun is a typical term pattern in French (e.g. navigateur web. One of the aims of this article is to find the typical term patterns and their frequency in the domain of social sciences. For this reason, three articles were chosen as corpus in the social sciences domain with the criterion that they include frequently the words famille ’family’ and/or individu ’individual’. In the three articles, all terms were manually annotated. The other aim of this article is to compare the frequencies of the term patterns in social sciences with the results of previous research on terms of a corpus of computer science. The further aim of this analysis is to determine whether an automatic term extractor fine-tuned for texts on computer science could also be used on a corpus of social sciences. In order to achieve this goal, problematic patterns – like adjectives preceding the nominal head in a term – are also examined. The results showed that the IT corpus followed the same tendency as the corpus on human sciences; however, juxtaposed nouns are less frequent in the latter which prefers the noun-adjective sequence. Concerning the problematic patterns, the two corpora did not show important differences: their presence is minimal in both (~7%. So the same rule-based extractor could work well on both corpora; however, psychological and sociological terms are more frequently used in common language, which makes statistical filtering more difficult.

  18. Contribution to the study of can deformations in the fuel elements of gas-graphite reactors during thermal cycling; Contribution a l'etude des deformations des gaines des elements combustibles de reacteur graphite-gaz au cours du cyclage thermique

    Energy Technology Data Exchange (ETDEWEB)

    Gauthron, M; Boudouresques, B; Delpeyroux, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The cans of fuel cartridges used in reactors of the gas-graphite type have either longitudinal fins of variable thickness, short herring-bone fins, or else a mixture of the two. An important test of the strength of these cartridges is their behaviour during thermal cycling carried out in cells reproducing in-pile conditions. It has been observed during with rapid cooling that there occurs a shortening at the base of the fins which can be accompanied in particular by a compression effect at the fin type, which has a tendency to curl, and by a tractive force acting on the body of the can at the ends of the longitudinal fins; this last phenomenon can result in a fracturing of the welds at the extremities or of the ends of the cartridge. This report presents first of all the way in which the stress diagram can be drawn for a can touching the fuel, and then the effect of the ratchet along a fin fixed to a bar with or without grooves. Finally the importance is shown of the test cycling variables (temperature, heating and cooling rates). (authors) [French] Les gaines des cartouches combustibles des reacteurs de la filiere graphite-gaz comportent soit des ailettes longitudinales plus ou moins epaisses, soit de courtes ailettes a chevrons, soit un ensemble des deux. Un test important de la tenue des cartouches, est la tenue au cyclage thermique en cellule pour reproduire le comportement en pile. On a observe au cours des cyclages a refroidissement rapide, un raccourcissement a la base des ailettes qui peut s'accompagner notamment d'une mise en compression du sommet de l'ailette qui a tendance a friser, et d'une traction exercee sur le corps des gaines au bout des ailettes longitudinales; ce dernier phenomene peut se traduire par des ruptures de soudures d'extremites ou des parties terminales de la cartouche. Ce rapport presente d'abord la maniere dont peut etre trace le diagramme des contraintes dans une gaine liee au combustible, puis l'effet du rochet le long d

  19. Small-Angle Scattering of Neutrons by Iron and Nickel Close to the Curie Point; Diffusion aux petits angles des neutrons par le fer et le nickel au voisinage du point de curie; Rasseyanie nejtronov pod malymi uglami zhelezom i nikelem, blizkikh k tochke kyuri; Dispersion de neutrones en angulos pequenos por el hierro y el niquel cerca del punto de curie

    Energy Technology Data Exchange (ETDEWEB)

    Jacrot, B.; Konstantinovic, J.; Parette, G.; Cribier, D. [Centre d' etudes Nucleaires de Saclay (France)

    1963-01-15

    Recent studies on critical scattering by iron have thrown fresh light on the results obtained previously and shown that: (1) At the Curie point, scattering is inelastic. The Lorentzian form of the lines and their angular dependence establish the existence of a scattering process having the diffusion coefficient 2m {Omega}/n = 7. (2) At the Curie point, the coefficient K{sub 1}{sup 2} is less than 5 x 10{sup -5} A{sup -2}. Iron and nickel have very different angular distribution. Small-angle scattering below T{sub c} has also been studied. (author) [French] De nouveaux travaux sur la diffusion critique par le fer ont permis de completer les resultats obtenus anterieurement. Ils etablissent les faits suivants: 1. Au point de Curie la diffusion est inelastique. La forme lorentzienne des raies et leur dependance angulaire etablissent l'existence d*un processus de diffusion avec un coefficient de diffusion 2m{Omega}/n = 7. 2. Au point de Curie le coefficient K{sub 1}{sup 2} est inferieur a 5 x 10{sup -5} A{sup -2}. La distribution angulaire est tres differente dans le cas du fer et du nickel. On a egalement etudie la diffusion aux petits angles en dessous de T{sub c}. (author) [Spanish] Nuevos trabajos sobre la dispersion critica por el hierro han permitido completar los resultados obtenidos anteriormente. Dichos trabajos prueban los hechos siguientes: 1) La dispersion es inelastica en el punto de Curie. La forma lorentziana de las rayas y su dependencia angular demuestran la existencia de un proceso de dispersion con un coeficiente de dispersion igual a 2m {Omega}/n = 7. 2) En el punto de Curie, el coeficiente K{sub 1}{sup 2} es inferior a 5 x 10{sup -5} A{sup -2}. La distribucion angular es muy diferente en el caso del hierro y del ni quel. Se ha estudiado tambien la dispersion en pequenos angulos por debajo de T{sub c}. (author)

  20. Effet de la rugosité de surface sur les performances du contact ...

    African Journals Online (AJOL)

    Effet de la rugosité de surface sur les performances du contact segment- chemise dans un moteur à combustion interne. The effect of surface roughness on the performances of liner-piston ring contact in internal combustion engine. Amar Ayad. *. , Amar Skendraoui & Ammar Haiahem. Laboratoire de Mécanique Industrielle ...

  1. Tubular combustion

    CERN Document Server

    Ishizuka, Satoru

    2014-01-01

    Tubular combustors are cylindrical tubes where flame ignition and propagation occur in a spatially confined, highly controlled environment, in a nearly flat, elongated geometry. This allows for some unique advantages where extremely even heat dispersion is required over a large surface while still maintaining fuel efficiency. Tubular combustors also allow for easy flexibility in type of fuel source, allowing for quick changeover to meet various needs and changing fuel pricing. This new addition to the MP sustainable energy series will provide the most up-to-date research on tubular combustion--some of it only now coming out of private proprietary protection. Plentiful examples of current applications along with a good explanation of background theory will offer readers an invaluable guide on this promising energy technology. Highlights include: * An introduction to the theory of tubular flames * The "how to" of maintaining stability of tubular flames through continuous combustion * Examples of both small-scal...

  2. Advanced Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R. [NETL

    2013-03-11

    The activity reported in this presentation is to provide the mechanical and physical property information needed to allow rational design, development and/or choice of alloys, manufacturing approaches, and environmental exposure and component life models to enable oxy-fuel combustion boilers to operate at Ultra-Supercritical (up to 650{degrees}C & between 22-30 MPa) and/or Advanced Ultra-Supercritical conditions (760{degrees}C & 35 MPa).

  3. Checking the sealing of fuel elements by helium sweating - case of the reactors G2 (1960); Controle de l'etancheite des elements combustibles par ressuage d'helium - cas du reacteur G2 (1960)

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, B; D' Orival, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Choumoff, S [Compagnie Francaise Thomson-Houston, 75 - Paris (France)

    1960-07-01

    The G2 slug is a welded, hermetically sealed unit; the seal is checked by placing the fuel element in a helium atmosphere under pressure, then measuring the quantity of helium it releases in a vessel under vacuum. The theoretical aspect and the conditions of industrial application are reviewed, and the installations described. (author) [French] La cartouche G2 se presente comme un ensemble soude, hermetique; le controle d'etancheite s'effectue en immergeant l'element combustible dans une atmosphere d'helium sous pression puis en mesurant la quantite d'helium qu'il restitue dans une enceinte sous vide. L'aspect theorique et les conditions d'exploitation industrielle sont evoques et les installations decrites. (auteur)

  4. Study of a device for the direct measurement of the fission gas pressure inside an in-pile fuel element; Etude d'un dispositif pour la mesure directe de la pression des gaz de fission a l'interieur d'un element combustible en pile

    Energy Technology Data Exchange (ETDEWEB)

    Lavaud, B; Uschanoff, S [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The fission gas pressure inside a fuel element made of a refractory fuel constitutes an important limiting factor for the burn-up. Although it is possible to calculate approximately the volume of gas produced outside the fuel during its life-time; it is nevertheless very difficult to evaluate the pressure since the volume allowed to the fission gases, as well as their temperature are known only very approximately. This physical value, which is essential for the technologist, can only be known by direct in-pile measurement of the pressure. The report describes the equipment which has been developed for this test. (authors) [French] La pression des gaz de fission a l'interieur d'un element combustible a combustible refractaire constitue une des limitations importantes du taux de combustion. Si on peut approcher par calcul la determination du volume, des gaz degages hors du combustible au cours de sa vie, il est par contre tres difficile d'evaluer la pression car le volume alloue aux gaz de fission et leur temperature sont tres mal connus. Cette donnee essentielle pour le technologue ne peut etre atteinte que par une mesure directe en pile de la pression. Le rapport decrit l'appareillage qui a ete mis au point pour cet essai. (auteurs)

  5. Fiche technique du spermogramme et du spermocytogramme ...

    African Journals Online (AJOL)

    En Afrique la stérilité du couple constitue un drame social. Selon l'OMS, environ 8 à 12 % des couples africains sont touchés par une infertilité. La responsabilité masculine dans la stérilité est comprise entre 30 à 40%. Les causes de l'infertilité masculine peuvent être l'impuissance et/ ou l'altération du sperme. L'étude de ...

  6. OPERATION DU FOISONNEMENT

    Directory of Open Access Journals (Sweden)

    Gholamreza Djelveh

    2010-04-01

    Full Text Available Mousses alimentaires sont un sous-ensemble des aliments connus sous le nom de produits fouettés ou des produits aérés. Ils sont des produits formulés avec des qualités telles que la légèreté et la souplesse et sont principalement consommés à l'apéritif ou au dessert. Les produits en mousse obtenue par dispersion d'un gaz dans une matrice alimentaire (la phase continue ont connu un développement croissant au cours des années 80 et 90. Le processus d'aération liés à leurs activités de production est appelée l'expansion ou à fouetter. Le document présente les principaux-paramètres du procédé du point permanent de la formulation, la mise en œuvre processus dans les installations pilotes et à l'échelle industrielle, la caractérisation des produits finis, la base énergétique de l'échelle de processus en place, et le lien entre la formulation, émulsion préparation de l'expansion. Cette vue d'ensemble de l'opération d'expansion continue, nous a permis de mettre en évidence le fait qu'il ya des opérations de l'unité encore mal décrite par le génie des procédés et pour lesquels les méthodes et outils pour l'extrapolation et la prédiction sont encore à leurs balbutiements.

  7. Les Cahiers du CREAD

    African Journals Online (AJOL)

    Admin

    politique de bas prix exercée par la Russie et le Qatar vient confirmer ce constat ; s'ajoute à cela l'entrée éventuelle du gaz non conven- tionnel, dont son prix actuel de 3/4 $US, offre aux USA l'opportunité d'être exportateur de ..... les compagnies à produire en matière du gaz naturel, tels le prix du gaz naturel, le prix des ...

  8. Bulletin du CRDI #124

    International Development Research Centre (IDRC) Digital Library (Canada)

    Les femmes jouent un rôle important dans les exploitations minières artisanales et à petite échelle en Afrique subsaharienne. De concert ... Couverture du livre: Une vie saine pour les femmes et les enfants vulnérables · Couverture du livre: Entre el activismo y la intervención · Couverture du livre: Revitalizing Health for All.

  9. Bulletin du CRDI #125

    International Development Research Centre (IDRC) Digital Library (Canada)

    L'IOSRS remporte le prix de la diplomatie scientifique · GrowInclusive : la plateforme tant attendue est en construction · Toutes les nouvelles. Activités à venir. Semaine du développement international 2018. Le CRDI célébrera la Semaine du développement international du 4 au 10 février 2018. Suivez-nous sur Twitter et ...

  10. Experimental validation for combustion analysis of GOTHIC code in 2-dimensional combustion chamber

    International Nuclear Information System (INIS)

    Lee, J. W.; Yang, S. Y.; Park, K. C.; Jung, S. H.

    2002-01-01

    In this study, the prediction capability of GOTHIC code for hydrogen combustion phenomena was validated with the results of two-dimensional premixed hydrogen combustion experiment executed by Seoul National University. The experimental chamber has about 24 liter free volume (1x0.024x1 m 3 ) and 2-dimensional rectangular shape. The test were preformed with 10% hydrogen/air gas mixture and conducted with combination of two igniter positions (top center, top corner) and two boundary conditions (bottom full open, bottom right half open). Using the lumped parameter and mechanistic combustion model in GOTHIC code, the SNU experiments were simulated under the same conditions. The GOTHIC code prediction of the hydrogen combustion phenomena did not compare well with the experimental results. In case of lumped parameter simulation, the combustion time was predicted appropriately. But any other local information related combustion phenomena could not be obtained. In case of mechanistic combustion analysis, the physical combustion phenomena of gas mixture were not matched experimental ones. In boundary open cases, the GOTHIC predicted very long combustion time and the flame front propagation could not simulate appropriately. Though GOTHIC showed flame propagation phenomenon in adiabatic calculation, the induction time of combustion was still very long compare with experimental results. Also, it was found that the combustion model of GOTHIC code had some weak points in low concentration of hydrogen combustion simulation

  11. Study of the dynamic behaviour of the reactor Rapsodie; Etude du comportement dynamique de la pile rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Abdon, R; Chaigne, M [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1964-07-01

    . The investigation of the control, carried out on analog computer, served to determine the different possible means of starting and changing the conditions of the reactor as well as its automatic control. The calculations were examined in the totality by the construction of a training simulator composed of a board similar to the control board of the reactor, all of whose commands (reactivity and flows) work on an analogue computer which resolves in the real time the dynamic equations of the reactor and which reproduces simultaneously all the parameters representing the state of the installation (power, period, temperatures, etc. ) in the case of various incidents as well as under normal conditions of functioning. (authors) [French] On sait que le developpement des reacteurs surgenerateurs a neutrons rapides pose des problemes nouveaux d'une part dans les domaines mecanique et thermique et d'autre part en ce qui concerne leur comportement dynamique et leur surete. La pile RAPSODIE a ete l'objet de tres nombreuses etudes dynamiques effectuees sur machines analogiques et digitales, pour deux versions du combustible (metal et oxyde). Apres elaboration des modeles mathematiques representatifs de l'ensemble de l'installation (bloc pile et circuit de refroidissement) tant du point de vue neutronique que du point de vue thermodynamique, on a mis au point les schemas analogiques et les codes digitaux utilisables pour mener a bien les simulations d'incidents, de conduite et de stabilite du reacteur. On s'est attache, par rapport aux methodes habituelles a obtenir une precision plus grande, par un decoupage en zones plus fines, par l'emploi de formulations plus representatives du systeme reel, voire solubles analytiquement. Les etudes d'incidents ont ete effectuees par voie analogique pour l'ensemble de l'installation et par voie digitale pour l'etude du bloc pile seul ou de l'installation fonctionnant avec un seul circuit thermique. Un programme complementaire special - qui, a

  12. Etablissement du pollutogramme et de l'hydrogramme de la rivière ...

    African Journals Online (AJOL)

    Ecole d'Aquaculture de la Vallée, Université Nationale d'Agriculture, République du Bénin. ... obtenus ont montré qu'à partir du point de déversement des eaux provenant de la station d'épuration, .... qualité physico-chimique et biologique du.

  13. High Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL's High-Pressure Combustion Research Facility in Morgantown, WV, researchers can investigate new high-pressure, high-temperature hydrogen turbine combustion...

  14. Combustion Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Combustion Research Laboratory facilitates the development of new combustion systems or improves the operation of existing systems to meet the Army's mission for...

  15. Combustion chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    This research is concerned with the development and use of sensitivity analysis tools to probe the response of dependent variables to model input variables. Sensitivity analysis is important at all levels of combustion modeling. This group`s research continues to be focused on elucidating the interrelationship between features in the underlying potential energy surface (obtained from ab initio quantum chemistry calculations) and their responses in the quantum dynamics, e.g., reactive transition probabilities, cross sections, and thermal rate coefficients. The goals of this research are: (i) to provide feedback information to quantum chemists in their potential surface refinement efforts, and (ii) to gain a better understanding of how various regions in the potential influence the dynamics. These investigations are carried out with the methodology of quantum functional sensitivity analysis (QFSA).

  16. Prévision de l'épaisseur du film passif d'un acier inoxydable 316L soumis au fretting corrosion grâce au Point Defect Model, PDM Predicting the steady state thickness of passive films with the Point Defect Model in fretting corrosion experiments

    Directory of Open Access Journals (Sweden)

    Geringer Jean

    2013-11-01

    Full Text Available Les implants orthopédiques de hanche ont une durée de vie d'environ 15 ans. Par exemple, la tige fémorale d'un tel implant peut être réalisée en acier inoxydable 316L ou 316LN. Le fretting corrosion, frottement sous petits déplacements, peut se produire pendant la marche humaine en raison des chargements répétés entre le métal de la prothèse et l'os. Plusieurs investigations expérimentales du fretting corrosion ont été entreprises. Cette couche passive de quelques nanomètres, à température ambiante, est le point clef sur lequel repose le développement de notre civilisation, selon certains auteurs. Ce travail vise à prédire les épaisseurs de cette couche passive de l'acier inoxydable soumis au fretting corrosion, avec une attention spécifique sur le rôle des protéines. Le modèle utilisé est basé sur le Point Defect Model, PDM (à une échelle microscopique et une amélioration de ce modèle en prenant en compte le processus de frottement sous petits débattements. L'algorithme génétique a été utilisé pour optimiser la convergence du problème. Les résultats les plus importants sont, comme démontré avec les essais expérimentaux, que l'albumine, la protéine étudiée, empêche les dégradations de l'acier inoxydable aux plus faibles concentrations d'ions chlorure ; ensuite, aux plus fortes concentrations de chlorures, un temps d'incubation est nécessaire pour détruire le film passif. Some implants have approximately a lifetime of 15 years. The femoral stem, for example, should be made of 316L/316LN stainless steel. Fretting corrosion, friction under small displacements, should occur during human gait, due to repeated loadings and un-loadings, between stainless steel and bone for instance. Some experimental investigations of fretting corrosion have been practiced. As well known, metallic alloys and especially stainless steels are covered with a passive film that prevents from the corrosion and degradation

  17. Biomass Conversion to Hydrocarbon Fuels Using the MixAlcoTM Process Conversion de la biomasse en combustibles hydrocarbonés au moyen du procédé MixAlcoTM

    Directory of Open Access Journals (Sweden)

    Taco-Vasquez S.

    2013-04-01

    Full Text Available The MixAlcoTM process converts biomass to hydrocarbons (e.g., gasoline using the following generic steps: pretreatment, fermentation, descumming, dewatering, thermal ketonization, distillation, hydrogenation, oligomerization and saturation. This study describes the production of bio-gasoline from chicken manure and shredded office paper, both desirable feedstocks that do not require pretreatment. Using a mixed culture of microorganisms derived from marine soil, the biomass was fermented to produce a dilute aqueous solution of carboxylate salts, which were subsequently descummed and dried. The dry salts were thermally converted to raw ketones, which were distilled to remove impurities. Using Raney nickel catalyst, the distilled ketones were hydrogenated to mixed secondary alcohols ranging from C3 to C12. Using zeolite HZSM-5 catalyst, these alcohols were oligomerized to hydrocarbons in a plug -flow reactor. Finally, these unsaturated hydrocarbons were hydrogenated to produce a mixture of hydrocarbons that can be blended into commercial gasoline. Le procédé MixAlcoTM convertit la biomasse en hydrocarbures (par exemple, en essence selon les étapes génériques suivantes : prétraitement, fermentation, écumage, déshydratation, cétonisation thermique, distillation, hydrogénation, oligomérisation et saturation. Cette étude décrit la production de bioessence à partir de fumier de poulet et de papier en lambeaux, ces deux sources étant des matières premières convoitées ne nécessitant pas de prétraitement. À l’aide d’une culture mixte de microorganismes dérivés de sols marins, la biomasse a été soumise à une fermentation de manière à produire une solution aqueuse diluée de sels de carboxylates, ultérieurement écumés et séchés. Les sels séchés ont été thermiquement convertis en cétones brutes, ensuite distillées afin d’éliminer les impuretés. À l’aide du catalyseur à base de nickel de Raney, les c

  18. "Cirque du Freak."

    Science.gov (United States)

    Rivett, Miriam

    2002-01-01

    Considers the marketing strategies that underpin the success of the "Cirque du Freak" series. Describes how "Cirque du Freak" is an account of events in the life of schoolboy Darren Shan. Notes that it is another reworking of the vampire narrative, a sub-genre of horror writing that has proved highly popular with both adult and…

  19. Rotary combustion device

    NARCIS (Netherlands)

    2008-01-01

    Rotary combustion device (1) with rotary combustion chamber (4). Specific measures are taken to provide ignition of a combustible mixture. It is proposed that a hollow tube be provided coaxially with the axis of rotation (6), so that a small part of the mixture is guided into the combustion chamber.

  20. Mise au point

    African Journals Online (AJOL)

    tomie est replacé et fixé par des fils d'acier, krönlein lais- sait ce fragment pédiculé au fascia temporalis afin d'évi- ter la dépression de la fosse temporale due à la désinser- tion du muscle temporal [20] ; dans notre série, après reconstitution du cadre, le muscle temporal est suturé à son point d'insertion. pour les tumeurs ...

  1. Novel Active Combustion Control Valve

    Science.gov (United States)

    Caspermeyer, Matt

    2014-01-01

    This project presents an innovative solution for active combustion control. Relative to the state of the art, this concept provides frequency modulation (greater than 1,000 Hz) in combination with high-amplitude modulation (in excess of 30 percent flow) and can be adapted to a large range of fuel injector sizes. Existing valves often have low flow modulation strength. To achieve higher flow modulation requires excessively large valves or too much electrical power to be practical. This active combustion control valve (ACCV) has high-frequency and -amplitude modulation, consumes low electrical power, is closely coupled with the fuel injector for modulation strength, and is practical in size and weight. By mitigating combustion instabilities at higher frequencies than have been previously achieved (approximately 1,000 Hz), this new technology enables gas turbines to run at operating points that produce lower emissions and higher performance.

  2. Magnox Fuel Cycles; Cycles des combustibles gaines de magnox; Toplivnye tsikly magnoks; Ciclos de combustible magnox

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, A. [United Kingdom Atomic Energy Authority, Risley, Warrington, Lancs (United Kingdom)

    1963-10-15

    The interaction between reactivity flux and temperature distributions and irradiation patterns caused by different refuelling policies is considered and present calculation methods outlined. Various refuelling schemes for both batch and continuous discharge systems are compared. The problem of the efficient irradiation of the first charge is considered together with delayed onset refuelling and shuffling schemes. The economic advantages and problems of using non-natural uranium in flattened reactors are discussed. The practical consideration of on-load refuelling schemes on new reactors are considered and reference is made to the experience gained on Bradwell and Berkeley. The effect of the variation of fuel cost and endurance on fuel-cycle economics is outlined. (author) [French] L'auteur etudie en premier lieu l'interaction entre les distributions de la temperature du flux et de la reactivite, d'une part, et le regime de l'irradiation, d'autre part, dans le cas de differents programmes de rechargement du combustible et il decrit brievement les methodes de calcul actuelles. Il compare ensuite differents programmes de rechargement du combustible pour le dechargement par lots et le dechargement continu. Il etudie le probleme de l'irradiation effica ce de la premiere charge dans le cadre de programmes de remplacement et de deplacement des cartouches a action retardee. Il analyse les avantages economiques de l'utilisatio n d'uranium non naturel dans les reacteurs a flux aplati et les problemes qu'elle pose. Il examine les aspects pratiques des programmes de rechargement en marche pour les nouveaux reacteurs, en se referant a l'experience acquise au moyen des reacteurs de Bradwell et de Berkeley. Enfin, il decrit brievement les effets des variations du cout et de la resistance du combustible sur l'economie des cycles de combustible. (author) [Spanish] La memoria estudia la interaccion entre el flujo de reactividad y la distribucion de temperaturas, asi como los

  3. Les méthodes thermiques de production des hydrocarbures. Chapitre 5 : Combustion "in situ". Pricipes et études de laboratoire Thermal Methods of Hydrocarbon Production. Chapter 5 : "In Situ" Combustion. Principles and Laboratory Research

    Directory of Open Access Journals (Sweden)

    Burger J.

    2006-11-01

    Full Text Available II existe plusieurs variantes de la combustion in situ, suivant le sens de déplacement du front de combustion, à co-courant ou à contre-courant, et suivant la nature des fluides injectés, air seul ou injection combinée d'air et d'eau. Les réactions de pyrolyse, d'oxydation et de combustion mises en jeu par ces techniques sont discutées, en particulier la cinétique des principaux mécanismes réactionnels, l'importance du dépôt de coke et l'exothermicité des réactions d'oxydation et de combustion. Les résultats d'essais de déplacement unidirectionnel du front de combustion dans des cellules de laboratoire sont présentés et discutés. Enfin on indique les conditions pratiques d'application des méthodes de combustion in situ sur champ. Possible variations of in situ combustion technique ore as follows : forward or reverse combustion depending on the relative directions of the air flow and the combustion front, dry combustion if air is the only fluid injected into the oil-bearing formation, or fixe/woter flooding if water is injected along with air. The chemical reactions of pyrolysis, oxidation and combustion involved in these processes are described. The kinetics of these reactions is discussed as well as fuel availability in forward combustion and the exothermicity of the oxidation and combustion reactions. The results obtained in the laboratory when a combustion front propagates in unidirectional adiabatic tells are described and discussed. This type of experimentation provides extensive information on the characteristics of the processes. Screening criteria for the practical application of in situ combustion techniques are presented.

  4. Combustion 2000

    Energy Technology Data Exchange (ETDEWEB)

    A. Levasseur; S. Goodstine; J. Ruby; M. Nawaz; C. Senior; F. Robson; S. Lehman; W. Blecher; W. Fugard; A. Rao; A. Sarofim; P. Smith; D. Pershing; E. Eddings; M. Cremer; J. Hurley; G. Weber; M. Jones; M. Collings; D. Hajicek; A. Henderson; P. Klevan; D. Seery; B. Knight; R. Lessard; J. Sangiovanni; A. Dennis; C. Bird; W. Sutton; N. Bornstein; F. Cogswell; C. Randino; S. Gale; Mike Heap

    2001-06-30

    . To achieve these objectives requires a change from complete reliance of coal-fired systems on steam turbines (Rankine cycles) and moving forward to a combined cycle utilizing gas turbines (Brayton cycles) which offer the possibility of significantly greater efficiency. This is because gas turbine cycles operate at temperatures well beyond current steam cycles, allowing the working fluid (air) temperature to more closely approach that of the major energy source, the combustion of coal. In fact, a good figure of merit for a HIPPS design is just how much of the enthalpy from coal combustion is used by the gas turbine. The efficiency of a power cycle varies directly with the temperature of the working fluid and for contemporary gas turbines the optimal turbine inlet temperature is in the range of 2300-2500 F (1260-1371 C). These temperatures are beyond the working range of currently available alloys and are also in the range of the ash fusion temperature of most coals. These two sets of physical properties combine to produce the major engineering challenges for a HIPPS design. The UTRC team developed a design hierarchy to impose more rigor in our approach. Once the size of the plant had been determined by the choice of gas turbine and the matching steam turbine, the design process of the High Temperature Advanced Furnace (HITAF) moved ineluctably to a down-fired, slagging configuration. This design was based on two air heaters: one a high temperature slagging Radiative Air Heater (RAH) and a lower temperature, dry ash Convective Air Heater (CAH). The specific details of the air heaters are arrived at by an iterative sequence in the following order:-Starting from the overall Cycle requirements which set the limits for the combustion and heat transfer analysis-The available enthalpy determined the range of materials, ceramics or alloys, which could tolerate the temperatures-Structural Analysis of the designs proved to be the major limitation-Finally the commercialization

  5. Un point de généalogie sur deux orfèvres parisiens du XIXe siècle : les « Favier » orfèvres parisiens de grosserie

    Directory of Open Access Journals (Sweden)

    Claude Aliquot

    2009-11-01

    Full Text Available C’est par un arrêté du directoire exécutif en date du 21 Brumaire an V (11 novembre 1796 qu’il a été fait obligation aux fabricants de métaux précieux d’insculper, sur une table de cuivre déposée dans les bureaux de l’administration, leur nouveau poinçon afin de les identifier, le contenu de cette insculpation de forme losangique étant laissé à la diligence de l’orfèvre. Il devait être biffé lors de l’arrêt d’activité du titulaire ; ceci n’a pas toujours été le cas, comme le montre l’examen de la production de l’atelier Favier.A departmental order of the Executive Directory, signed on 21 Brumaire Year V (11 November 1796 instructed craftsmen working with precious metals to inscribe their new proof-mark on a copper plate table held in the offices of the administration. This proof-mark, designed to identify the silver or gold smith was to be in the shape of a lozenge but its contents were left to the diligence of the smith. It was supposedly struck off the record when the craftsman ceased operations, but this was not necessarily the case, as our examination of the production of the Favier workshop demonstrates.

  6. Reduced NOX combustion method

    International Nuclear Information System (INIS)

    Delano, M.A.

    1991-01-01

    This patent describes a method for combusting fuel and oxidant to achieve reduced formation of nitrogen oxides. It comprises: It comprises: heating a combustion zone to a temperature at least equal to 1500 degrees F.; injecting into the heated combustion zone a stream of oxidant at a velocity within the range of from 200 to 1070 feet per second; injecting into the combustion zone, spaced from the oxidant stream, a fuel stream at a velocity such that the ratio of oxidant stream velocity to fuel stream velocity does not exceed 20; aspirating combustion gases into the oxidant stream and thereafter intermixing the aspirated oxidant stream and fuel stream to form a combustible mixture; combusting the combustible mixture to produce combustion gases for the aspiration; and maintaining the fuel stream substantially free from contact with oxidant prior to the intermixture with aspirated oxidant

  7. Kinetic study of diesel soot oxidation: application to simulation of diesel particulate filter regeneration; Etude cinetique de la combustion des suies diesel: application a la modelisation de la regeneration du filtre a particule

    Energy Technology Data Exchange (ETDEWEB)

    Huguet, Ch.

    2005-11-15

    Because of their toxicity, soot are considered as the most important pollutant from Diesel engines. The Diesel Particulate Filter (DPF) is widely deployed in Europe to address the significant reductions in particulate emissions required by increasingly stringent emission standards, both for heavy duty vehicles and passenger cars. Such a DPF filtrates above 99% of soot emissions and must be regularly regenerated. The use of additive allows to decrease the soot oxidation temperature to values which can be reached by appropriate engine tuning. The soot addition is a dominant parameter for the development of regeneration strategies. Its influence must be correctly represented by models. This Ph-D was performed at IFP in collaboration with ADEME and was supported by the LCSR at Orleans. The aim of the present research is to develop a kinetic mechanism characteristic of Diesel soot oxidation, which can be integrated into a DPF regeneration model and used for engine control. The oxidation study was based on soot characterisation and reaction kinetics investigations. The samples of Diesel soot were collected, without and with Cerium/Iron additive, by using two engines points representative of two normalized European cycles (ECE and EUDC). Thermal and composition analyses with techniques such as XPS, XRD or TEM were used to determine their physical and chemical properties. Their oxidation kinetics was experimentally studied on a synthetic gas bench (SGB) with a fixed bed reactor. Different tests were performed: temperature-programmed oxidation (TPO), Isothermal oxidation (IO), and sequential oxidation. The results allowed to correlate Diesel soot physical and chemical properties with their oxidation rate. A kinetic model was developed, which is based on global carbon consummation law and distinguishes the oxidation of different soot components. The simulation results agree very well with the experimental results of Diesel soot oxidation. (author)

  8. Combustion synthesis of inorganic materials; Muki zairyo no nensho gose

    Energy Technology Data Exchange (ETDEWEB)

    Oyanagi, M. [Ryukoku University, Kyoto (Japan)

    1999-11-01

    Combustion synthesis of porous titan carbide is outlined. In combustion synthesis, exothermic chain reaction, which is induced by igniting at one point of the simple substance mixture, propagates the combustion wave, and the compound is synthesized, which can be sintered by it. By this method, to this day intermetallic compounds, ceramics and high melting point composite materials have been synthesized, and synthetics can be made compact by adding pressure during or just after the reaction. Recently, applying the induction heating jointly, preheating before the reaction and heat treatment after the reaction can be controlled, accordingly, many high melting point inorganic compounds and composite materials can be made by combustion synthesis under pressure. (NEDO)

  9. Du Pont de Nemours

    NARCIS (Netherlands)

    Ros JPM; LAE

    1994-01-01

    Dit rapport over Du Pont de Nemours (produktie van o.a. chemische stoffen) is gepubliceerd binnen het Samenwerkingsproject Procesbeschrijvingen Industrie Nederland (SPIN). In het kader van dit project is informatie verzameld over industriele bedrijven of industriele processen ter ondersteuning

  10. Une technologie de pointe venue d'Asie modernise un secteur ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    28 oct. 2010 ... En assurant une combustion plus efficace, ajoute-t-il, on utilise moins d'arbres et on réduit la pollution de l'air. En 1996, le ministre du Commerce international du Canada a remis un certificat de reconnaissance à Hari Gunasingham pour souligner sa contribution à l'avancement de la science, des affaires ...

  11. Les Cahiers du CREAD

    African Journals Online (AJOL)

    Admin

    6 juil. 2007 ... La problématique du développement du secteur de l'artisanat en. Algérie a été très peu abordée par les chercheurs, qu'ils soient universitaires ou .... La loi a institué une taxe d'apprentissage dont le taux a été fixé à. 1% de la ...

  12. Les outils du CERN

    CERN Multimedia

    1999-01-01

    C'est le plus grand centre mondial de recherche en physique des particules. Les outils du Laboratoire, accélérateurs et détecteurs de particules, figurent parmi les instruments scientifiques les plus complexes au monde. Des prix Nobels ont d'ailleurs été attribués aux physiciens du CERN pour leurs développements.

  13. Bulletin du CRDI #127

    International Development Research Centre (IDRC) Digital Library (Canada)

    La mise à l'échelle de la recherche et de l'innovation en vue de créer un impact social constitue une priorité pour la communauté du développement. Toutefois ... Nous avons renouvelé notre soutien à la recherche auprès du gouvernement de l'Inde ... Des femmes étudient à l'École supérieure d'infotronique d'Haïti.

  14. Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — For more than 30 years The Combustion Research Facility (CRF) has served as a national and international leader in combustion science and technology. The need for a...

  15. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani; Oß wald, Patrick; Hansen, Nils; Kohse-Hö inghaus, Katharina

    2014-01-01

    . While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides

  16. Nitrous Oxide from Combustion and Industry: Chemistry, Emissions and Control Protoxyde d'azote provenant de la combustion et de l'industrie : chimie, émissions et techniques de réduction

    Directory of Open Access Journals (Sweden)

    De Soete G.

    2006-11-01

    Full Text Available After an Introductory Part, presenting a survey of the present knowledge of nitrous oxide chemistry related to fossil fuel combustion and flue gas treatment, as a background for the understanding of emission factors, the paper deals successively with the average N2O emission factors from combustion and other industrial sources, and gives guidelines for appropriate N2O control technology ; with respect to the former item, some comments and criticisms on the 1991 OEDC/IPCC Report are formulated. As far as updated emission sources are concerned, emphasis is put on those which presently constitute issues : emissions from fluidized bed combustors, emissions caused by non catalytic selective NO reduction by ammonia and urea injection, N2O emissions caused by the use of automotive three-way catalysts as well as emissions from nitric acid and adipic acid manufacturing and from municipal wastes and sewage sludges incineration. Comments on the 1991 OEDC/IPCC Report mainly emphasize : (1 the surprising absence of emission factors from stationary combustion facilities and the inadequacy of some of the scarcely presented data, (2 the strange ignorance of the important effect of aging of three-way catalysts on the emission of N2O from gasoline vehicles. These omissions are the more surprising since reliable information in these two fields were already available at the period the OEDC Report was issued and or revised. For the assessment of adequate N2O control technologies, there is an urgent need for further R&D work. Presently existing understanding of homogeneous and heterogeneous N2O chemistry may provide interesting hints for N2O control, either by gas phase treatment or by catalytic reduction, depending on the concentration levels present in the off-gases to be treated. Le but de cet article est double : d'une part il fait le point sur les facteurs d'émission de N2O provenant de la combustion des combustibles fossiles et de certains autres secteurs de l

  17. Maximal combustion temperature estimation

    International Nuclear Information System (INIS)

    Golodova, E; Shchepakina, E

    2006-01-01

    This work is concerned with the phenomenon of delayed loss of stability and the estimation of the maximal temperature of safe combustion. Using the qualitative theory of singular perturbations and canard techniques we determine the maximal temperature on the trajectories located in the transition region between the slow combustion regime and the explosive one. This approach is used to estimate the maximal temperature of safe combustion in multi-phase combustion models

  18. BP « Deepwater Horizon » du Golfe du Mexique à l’Afrique : un tournant pour l’industrie pétrolière ? BP “Deepwater Horizon” from the Gulf of Mexico to Africa : a turning point for the Oil Industry ?

    Directory of Open Access Journals (Sweden)

    Géraud Magrin

    2010-09-01

    Full Text Available L’explosion de la plateforme BP Deepwater Horizon du 20 avril 2010 constitue une des plus graves pollutions pétrolières de l’histoire. Sa localisation dans les eaux du premier consommateur mondial, et l’implication d’une des compagnies les plus avancées en matière de responsabilité sociale d’entreprise, sont révélatrices des enjeux actuels de la gestion environnementale des risques pétroliers. Alors que les gisements les plus accessibles sont exploités par des sociétés nationales, les compagnies internationales satisfont l’inextinguible demande en pétrole du système mondial en explorant des situations extrêmes, comme les eaux très profondes. Cela s’accompagne de risques croissants. La catastrophe de BP nous montre le danger de considérer un risque infime comme une absence de risque : l’exemption de planification d’urgence explique la longue durée et l’ampleur de la fuite. Elle rappelle aussi que les impacts du pétrole ne sont bien connus qu’à la surface et le long des côtes : or, cette fuite en eaux profondes causera des dommages écologiques graves dans les zones pélagiques. Cet événement changera les règles du jeu de la régulation environnementale pétrolière dans les zones sensibles. Nous donnons un aperçu des évolutions qu’il pourrait favoriser en Afrique, notamment en Mauritanie. Il reste à savoir si l’augmentation des coûts qui en résultera contribuera à accélérer la transition énergétique mondiale hors de la dépendance des hydrocarbures.On Thursday the 20th april 2010, the blowout of the Deepwater Horizon drilling platform operated by BP in the Gulf of Mexico starts what can be considered one of the major oil spills in the world history. Taking place in the national waters of the world’s first oil consumer and affecting one of the more advanced oil major in Corporate Social Responsibility, this accident may turn out to be a land mark for environmental management in the

  19. Évaluer la performance écologique d’un aménagement autoroutier du point de vue de la biodiversité végétale

    Directory of Open Access Journals (Sweden)

    MAYRAND, Flavie ; MARAGE, Damien ; GILLIOT, Jean-Marc ; MICHELIN, Joël ; COQUET, Yves

    2013-03-01

    Full Text Available La réglementation et les attentes sociétales incitent aujourd’hui les aménageurs du territoire à évaluer les impacts environnementaux de leurs projets de construction, mais également à prévoir des mesures et des actions pour créer ou restaurer la biodiversité des espaces modifiés. Des questions se posent donc aux gestionnaires sur les méthodes à utiliser et les indicateurs à employer pour évaluer la performance écologique d’un aménagement. Quelques éléments de réponse sont présentés ici, sur la base d’une étude de cas portant sur le Mont-aux-Liens, un aménagement paysager contigu à l’autoroute A19.

  20. Évaluer la performance écologique d’un aménagement autoroutier du point de vue de la biodiversité végétale

    Directory of Open Access Journals (Sweden)

    MAYRAND, Flavie

    2015-06-01

    Full Text Available La réglementation et les attentes sociétales incitent aujourd’hui les aménageurs du territoire à évaluer les impacts environnementaux de leurs projets de construction, mais également à prévoir des mesures et des actions pour créer ou restaurer la biodiversité des espaces modifiés. Des questions se posent donc aux gestionnaires sur les méthodes à utiliser et les indicateurs à employer pour évaluer la performance écologique d’un aménagement. Quelques éléments de réponse sont présentés ici, sur la base d’une étude de cas portant sur le Mont-aux-Liens, un aménagement paysager contigu à l’autoroute A19.

  1. Caractérisation de la variabilité climatique : cas du bassin versant ...

    African Journals Online (AJOL)

    DK

    anticlinaux plus étroits ... annuels des précipitations, est que, du point de vue stochastique, ceux-ci peuvent être considérés comme un .... uniforme pour la position du point de rupture la statistique U de Buishand est définie par. Ou: Pour k = 1, ..., N et ...

  2. Effet du Pediococcus acidilactici sur le bilan lipidique sanguin du ...

    African Journals Online (AJOL)

    Les résultats relatifs aux performances zootechniques ont montré que l'addition du probiotique a amélioré significativement le gain de poids pendant la phase de croissance se traduisant par un indice de consommation meilleur. Les dosages du cholestérol total, des triglycérides, du HDL et du LDL ont été déterminés à la ...

  3. The nuclear fuel cycle; Le cycle du combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    After a short introduction about nuclear power in the world, fission physics and the French nuclear power plants, this brochure describes in a digest way the different steps of the nuclear fuel cycle: uranium prospecting, mining activity, processing of uranium ores and production of uranium concentrates (yellow cake), uranium chemistry (conversion of the yellow cake into uranium hexafluoride), fabrication of nuclear fuels, use of fuels, reprocessing of spent fuels (uranium, plutonium and fission products), recycling of energetic materials, and storage of radioactive wastes. (J.S.)

  4. Sodium purification in Rapsodie; La purification du sodium a Rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Giraud, B [Commissariat a l' Energie Atomique, Dir. des Piles Atomiques, Cadarache (France). Centre d' Etudes Nucleaires

    1968-07-01

    This report is one of a series of publications presenting the main results of tests carried out during the start-up of the first french fast neutron reactor: Rapsodie. The article presents the sodium purification techniques used in the reactor cooling circuits both from the constructional point of view and with respect to results obtained during the first years working. (author) [French] Ce rapport fait partie d'une serie de publications presentant l'essentiel des resultats des essais effectues a l'occasion du demarrage du premier reacteur francais a neutrons rapides: RAPSODIE. Cet article expose les techniques de la purification du sodium utilise dans les circuits de refroidissement du reacteur tant au point de vue de leur realisation technologique, que des resultats obtenus pendant la premiere annee de fonctionnement. (auteur)

  5. Some physics aspects of cermet and ceramic fast systems; Quelques aspects de la physique des reacteurs a neutrons rapides utilisant des cermets et des ceramiques comme combustibles; Nekotorye fizicheskie aspekty kermetnykh i keramicheskikh sistem na bystrykh nejtronakh; Algunos aspectos fisicos de los sistemas rapidos a base de combustibles cermet y ceramicos

    Energy Technology Data Exchange (ETDEWEB)

    Codd, J; James, M F; Mann, J E [United Kingdom Atomic Energy Authority, Reactor Group (United Kingdom)

    1962-03-15

    The characteristics of a system using an iron-based oxide cermet as fuel material are discussed. A transport theory investigation to develop methods of predicting the effect of core heterogeneity on reactivity and flux distribution is described. Some preliminary calculations are also given of resonance self-shielding and Doppler temperature effects in a cermet system. (author) [French] Les auteurs etudient les caracteristique s d'un reacteur utilisant comme combustible un cermet d'oxydes a armature de fer. Ils exposent une application de la theorie du transport a la mise au point des methodes permettant de prevoir l'effet de l'heterogeneite du coeur sur la reactivite et sur la distribution du flux. Ils donnent egalement quelques calculs preliminaires d'effets d'autoprotection due a la resonance et d'effet Doppler du a la chaleur dans un reacteur utilisant un cermet. (author) [Spanish] La memoria discute las caracteristicas de un sistema que emplea como combustible un oxido tipo cermet a base de hierro. Describe una investigacion de la teoria de transporte con miras a desarrollar metodos para evaluar el efecto de la heterogeneidad del cuerpo sobre la reactividad y la distribucion de flujo. Tambien da algunos calculos preliminares de los efectos del autoblindaje por resonancia y de la temperatura de Doppler en un sistema de tipo cermet. (author) [Russian] Obsuzhdayutsya kharakteristiki sistemy, ispol'zuyushchej v kachestve toplivnogo materiala oksidnye kermety, razrabotannye na osnove zheleza. Opisyvaetsya issledovanie teorii perenosa, chtoby razvit' metody predskazaniya vliyaniya geterogennosti aktivnoj zony na reaktivnost' i raspredelenie potoka. Dayutsya takzhe nekotorye predvaritel'nye raschety ehffektov rezonansnoj samozashchity i temperaturnogo ehffekta Dopplera v kermetnoj sisteme. (author)

  6. Uncertainties in hydrogen combustion

    International Nuclear Information System (INIS)

    Stamps, D.W.; Wong, C.C.; Nelson, L.S.

    1988-01-01

    Three important areas of hydrogen combustion with uncertainties are identified: high-temperature combustion, flame acceleration and deflagration-to-detonation transition, and aerosol resuspension during hydrogen combustion. The uncertainties associated with high-temperature combustion may affect at least three different accident scenarios: the in-cavity oxidation of combustible gases produced by core-concrete interactions, the direct containment heating hydrogen problem, and the possibility of local detonations. How these uncertainties may affect the sequence of various accident scenarios is discussed and recommendations are made to reduce these uncertainties. 40 references

  7. Les mots du jazz

    OpenAIRE

    Roueff, Olivier

    2007-01-01

    L’ouvrage d’André Schaeffner constitue la première analyse savante du jazz (1926). Il a marqué une étape importante dans le processus de réinvention du jazz en France en contribuant notamment, par sa réception et les polémiques qu’il a suscitées, à transformer l’identification du jazz d’une musique « américaine » à une musique « noire-américaine » (c’est-à-dire aux « racines » africaines). Les analyses proposées dans cet ouvrage, alors qu’elles désignaient des musiques que la critique de jazz...

  8. Internal and surface phenomena in metal combustion

    Science.gov (United States)

    Dreizin, Edward L.; Molodetsky, Irina E.; Law, Chung K.

    1995-01-01

    Combustion of metals has been widely studied in the past, primarily because of their high oxidation enthalpies. A general understanding of metal combustion has been developed based on the recognition of the existence of both vapor-phase and surface reactions and involvement of the reaction products in the ensuing heterogeneous combustion. However, distinct features often observed in metal particle combustion, such as brightness oscillations and jumps (spearpoints), disruptive burning, and non-symmetric flames are not currently understood. Recent metal combustion experiments using uniform high-temperature metal droplets produced by a novel micro-arc technique have indicated that oxygen dissolves in the interior of burning particles of certain metals and that the subsequent transformations of the metal-oxygen solutions into stoichiometric oxides are accompanied with sufficient heat release to cause observed brightness and temperature jumps. Similar oxygen dissolution has been observed in recent experiments on bulk iron combustion but has not been associated with such dramatic effects. This research addresses heterogeneous metal droplet combustion, specifically focusing on oxygen penetration into the burning metal droplets, and its influence on the metal combustion rate, temperature history, and disruptive burning. A unique feature of the experimental approach is the combination of the microgravity environment with a novel micro-arc Generator of Monodispersed Metal Droplets (GEMMED), ensuring repeatable formation and ignition of uniform metal droplets with controllable initial temperature and velocity. The droplet initial temperatures can be adjusted within a wide range from just above the metal melting point, which provides means to ignite droplets instantly upon entering an oxygen containing environment. Initial droplet velocity will be set equal to zero allowing one to organize metal combustion microgravity experiments in a fashion similar to usual microgravity

  9. New class of combustion processes

    International Nuclear Information System (INIS)

    Merzhanov, A.G.; Borovinskaya, I.P.

    1975-01-01

    A short review is given of the results of work carried out since 1967 on studying the combustion processes caused by the interaction of chemical elements in the condensed phase and leading to the formation of refractory compounds. New phenomena and processes are described which are revealed when investigating the combustion of the systems of this class, viz solid-phase combustion, fast combustion in the condensed phase, filtering combustion, combustion in liquid nitrogen, spinning combustion, self-oscillating combustion, and repeated combustion. A new direction in employment of combustion processes is discussed, viz. a self-propagating high-temperature synthesis of refractory nitrides, carbides, borides, silicides and other compounds

  10. fibrosarcome du larynx

    African Journals Online (AJOL)

    pie du lit tumoral est employée comme complément thé- rapeutique [9] alors que la chimiothérapie est générale- ment indiquée dans les formes métastatiques. Le pronos- tic dépend essentiellement du degré de différentiation his- tologique. En fait, le fibrosarcome bien différencié est caractérisé par la fréquence de récidive ...

  11. du Chott Marouane

    African Journals Online (AJOL)

    plancton de 90 µm de vide de maille. Ils ont été conservés dans du formol à 5%. L'identification de l'espèce est basée sur des critères morphologiques [20]: la forme des furcas, les lobes frontaux des antennes des mâles, de l'organe copulateur (pénis) et du sac ovigère. Le comptage des soies furcales a été réalisé. L'étude ...

  12. Formations hybrides et interactions en ligne du point de vue de l'enseignant : pratiques, représentations, évolutions Blended learning and online interaction from the teacher's perspective: practice, representation and evolution

    Directory of Open Access Journals (Sweden)

    Christian Degache

    2008-10-01

    Full Text Available Les formations hybrides sont de plus en plus nombreuses dans le domaine des langues mais ne sont, une fois créées, pas toujours stables dans le temps. Devant ce constat, nous avons fait l'hypothèse, qui est au fondement du présent article, que ces évolutions sont liées au déroulement des interactions qui ont effectivement eu lieu dans le cadre de ces formations. Pour vérifier notre hypothèse, nous avons mené des entretiens, basés sur des questionnaires hétéro-administrés, avec 15 concepteurs de formations en langues pour spécialistes d'autres disciplines (Lansad conçues dans le cadre du projet Flodi. L'analyse des données ainsi obtenues a permis d'identifier les pratiques d'interaction, les représentations des concepteurs et les évolutions de formations hybrides. Elle montre que l'interaction effective est bien un facteur déterminant pour leur évolution. Par ailleurs, l'observation des évolutions passées, présentes ou futures nous a permis de distinguer quatre tendances des formations hybrides en langues : introductive (des Tice, optimisatrice, réorganisatrice et collaborative.Language training increasingly uses blended learning systems. One can state that the latter, once they are set up, often continue to be modified. We argue that these modifications are due to the interaction during the related training sessions. To verify our hypothesis we interviewed 15 designers of blended learning systems in the field of languages for specialists of other disciplines which are part of the Flodi-project, filling out questionnaires while interviewing them. An analysis of the data reveals interactional habits, course designers' representations, as well as past and foreseen modifications of the blended learning systems. The results show that interactions during training sessions did influence the evolution of the system. Moreover, we were able to distinguish between four tendencies of past, present and future modification of the

  13. Verification of Conditions for use of Combustion Products‘ Heat

    Directory of Open Access Journals (Sweden)

    Kažimírová Viera

    2015-06-01

    Full Text Available Presented contribution deals with the verification of conditions for use of combustion products‘ heat, generated by combustion of wood in a fireplace used in a household. It is necessary to know the temperature behaviour of the fireplace to determine the adequacy of the technical solution for using combustion products‘ heat. The combustion products‘ temperature at the upper part of the chimney is 80-120 °C. The dew point value was established to be below 51 °C. The average observed value of combustion product velocity is 1.6 m s-1. The volume flow rate of combustion products is 12 m3 h-1. Measured values allow for effective solution of the use of combustion products‘ heat.

  14. Combustion modeling in internal combustion engines

    Science.gov (United States)

    Zeleznik, F. J.

    1976-01-01

    The fundamental assumptions of the Blizard and Keck combustion model for internal combustion engines are examined and a generalization of that model is derived. The most significant feature of the model is that it permits the occurrence of unburned hydrocarbons in the thermodynamic-kinetic modeling of exhaust gases. The general formulas are evaluated in two specific cases that are likely to be significant in the applications of the model.

  15. Boiler using combustible fluid

    Science.gov (United States)

    Baumgartner, H.; Meier, J.G.

    1974-07-03

    A fluid fuel boiler is described comprising a combustion chamber, a cover on the combustion chamber having an opening for introducing a combustion-supporting gaseous fluid through said openings, means to impart rotation to the gaseous fluid about an axis of the combustion chamber, a burner for introducing a fluid fuel into the chamber mixed with the gaseous fluid for combustion thereof, the cover having a generally frustro-conical configuration diverging from the opening toward the interior of the chamber at an angle of between 15/sup 0/ and 55/sup 0/; means defining said combustion chamber having means defining a plurality of axial hot gas flow paths from a downstream portion of the combustion chamber to flow hot gases into an upstream portion of the combustion chamber, and means for diverting some of the hot gas flow along paths in a direction circumferentially of the combustion chamber, with the latter paths being immersed in the water flow path thereby to improve heat transfer and terminating in a gas outlet, the combustion chamber comprising at least one modular element, joined axially to the frustro-conical cover and coaxial therewith. The modular element comprises an inner ring and means of defining the circumferential, radial, and spiral flow paths of the hot gases.

  16. La communication, point aveugle du métier de chercheur mémoires et leçons d'un séminaire pluridisciplinaire 2009-2014, Clermont-Ferrand

    CERN Document Server

    Dacheux, Eric

    2015-01-01

    Séductrice, simplificatrice, inutile et surfaite, la communication est parée de tous les vices. Le chercheur n'y voit souvent qu'une contrainte institutionnelle, une obligation. Et pourtant, elle réside au coeur même de la science. Du thésard, échangeant avec son directeur, au prix Nobel, interviewé par les grands médias, en passant par les colloques internationaux, elle est le trait professionnel commun à tous les chercheurs. Et, si l'on s'intéresse à la dimension cognitive de la communication scientifique (le travail inter- disciplinaire), à sa dimension culturelle (la vulgarisation scientifique) ou à sa dimension politique (les controverses dans l'espace public), on pense rarement la « communication » comme pratique professionnelle. Depuis 2009, un séminaire expérimental, soutenu par l'ISCC et installé en Auvergne, conduit une recherche d'épistémologie comparée sur cette pratique professionnelle peu étudiée. Cet ouvrage collectif en tire les principaux enseignements et réunit les r�...

  17. Calculation of the working capital invested in fuel cycles and its interest charges (1963); Calcul des immobilisations financieres des cycles de combustible (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    All the processes undergone by the nuclear material, including the various steps of fuel element manufacturing and of irradiated fuel reprocessing lead to working capital investments varying with the type of reactor, that must be taken into account in the kWh cost calculation. The author deals with a calculation method called: 'present worth method' and gives some examples concerning reactors the main fuel of which being either natural uranium or enriched uranium or plutonium. He especially points out the importance these investments may take in the case of fast breeder reactors. (author) [French] L'ensemble des etapes parcourues par la matiere fissile comprenant les divers stades d'elaboration des elements combustibles et de leur traitement apres irradiation, implique des immobilisations financieres tres differentes d'un type de reacteur a l'autre, dont il convient de tenir compte dans le calcul du cout du kWh. L'auteur expose une methode de calcul dite 'd'actualisation des couts' et donne quelques exemples relatifs aux reacteurs utilisant l'uranium naturel, l'uranium enrichi et le plutonium comme combustible principal. Il montre en particulier l'importance que peuvent avoir ces immobilisations dans le cas des reacteurs surregenerateurs. (auteur)

  18. les cahiers du cread

    African Journals Online (AJOL)

    Our Journal “les cahiers du cread” is a quarterly economic review publishing original findings of empirical research and theoretical debates on fields pertaining to our mission coverage (Macro Economics, Industrial Economics and Firms, Human Development & Social Economics, Agriculture & Environment). Other websites ...

  19. Lump wood combustion process

    Science.gov (United States)

    Kubesa, Petr; Horák, Jiří; Branc, Michal; Krpec, Kamil; Hopan, František; Koloničný, Jan; Ochodek, Tadeáš; Drastichová, Vendula; Martiník, Lubomír; Malcho, Milan

    2014-08-01

    The article deals with the combustion process for lump wood in low-power fireplaces (units to dozens of kW). Such a combustion process is cyclical in its nature, and what combustion facility users are most interested in is the frequency, at which fuel needs to be stoked to the fireplace. The paper defines the basic terms such as burnout curve and burning rate curve, which are closely related to the stocking frequency. The fuel burning rate is directly dependent on the immediate thermal power of the fireplace. This is also related to the temperature achieved in the fireplace, magnitude of flue gas losses and the ability to generate conditions favouring the full burnout of the fuel's combustible component, which, at once ensures the minimum production of combustible pollutants. Another part of the paper describes experiments conducted in traditional fireplaces with a grate, at which well-dried lump wood was combusted.

  20. Study of experimental validation for combustion analysis of GOTHIC code

    International Nuclear Information System (INIS)

    Lee, J. Y.; Yang, S. Y.; Park, K. C.; Jeong, S. H.

    2001-01-01

    In this study, present lumped and subdivided GOTHIC6 code analyses of the premixed hydrogen combustion experiment at the Seoul National University and comparison with the experiment results. The experimental facility has 16367 cc free volume and rectangular shape. And the test was performed with unit equivalence ratio of the hydrogen and air, and with various location of igniter position. Using the lumped and mechanistic combustion model in GOTHIC6 code, the experiments were simulated with the same conditions. In the comparison between experiment and calculated results, the GOTHIC6 prediction of the combustion response does not compare well with the experiment results. In the point of combustion time, the lumped combustion model of GOTHIC6 code does not simulate the physical phenomena of combustion appropriately. In the case of mechanistic combustion model, the combustion time is predicted well, but the induction time of calculation data is longer than the experiment data remarkably. Also, the laminar combustion model of GOTHIC6 has deficiency to simulate combustion phenomena unless control the user defined value appropriately. And the pressure is not a proper variable that characterize the three dimensional effect of combustion

  1. Combustion stratification study of partially premixed combustion using Fourier transform analysis of OH* chemiluminescence images

    KAUST Repository

    Izadi Najafabadi, Mohammad

    2017-11-06

    A relatively high level of stratification (qualitatively: lack of homogeneity) is one of the main advantages of partially premixed combustion over the homogeneous charge compression ignition concept. Stratification can smooth the heat release rate and improve the controllability of combustion. In order to compare stratification levels of different partially premixed combustion strategies or other combustion concepts, an objective and meaningful definition of “stratification level” is required. Such a definition is currently lacking; qualitative/quantitative definitions in the literature cannot properly distinguish various levels of stratification. The main purpose of this study is to objectively define combustion stratification (not to be confused with fuel stratification) based on high-speed OH* chemiluminescence imaging, which is assumed to provide spatial information regarding heat release. Stratification essentially being equivalent to spatial structure, we base our definition on two-dimensional Fourier transforms of photographs of OH* chemiluminescence. A light-duty optical diesel engine has been used to perform the OH* bandpass imaging on. Four experimental points are evaluated, with injection timings in the homogeneous regime as well as in the stratified partially premixed combustion regime. Two-dimensional Fourier transforms translate these chemiluminescence images into a range of spatial frequencies. The frequency information is used to define combustion stratification, using a novel normalization procedure. The results indicate that this new definition, based on Fourier analysis of OH* bandpass images, overcomes the drawbacks of previous definitions used in the literature and is a promising method to compare the level of combustion stratification between different experiments.

  2. Flameless Combustion Workshop

    National Research Council Canada - National Science Library

    Gutmark, Ephraim

    2005-01-01

    .... "Flameless Combustion" is characterized by high stability levels with virtually no thermoacoustic instabilities, very low lean stability limits and therefore extremely low NOx production, efficient...

  3. Research Combustion Laboratory (RCL)

    Data.gov (United States)

    Federal Laboratory Consortium — The Research Combustion Laboratory (RCL) develops aerospace propulsion technology by performing tests on propulsion components and materials. Altitudes up to 137,000...

  4. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    Ashlines: To promote and support the commercially viable and environmentally sound recycling of coal combustion byproducts for productive uses through scientific research, development, and field testing.

  5. New combustion, environment regulations: the answers for natural gas; Nouvelles reglementations, combustion, environnement: les reponses pour le gaz naturel

    Energy Technology Data Exchange (ETDEWEB)

    Le Peltier-Marc, A. [Gaz de France (GDF), 75 - Paris (France)

    1997-12-31

    This paper reports on the point of view from Gaz de France (GdF) company concerning the potential consequences of the use of natural gas in combustion systems with respect to the new regulations about combustion and environment. Details concerning the measures relative to the limitation of pollutants in small combustion installations (2 - 20 MW) are given (chimney height, SO{sub x}, NO{sub x} and dusts content in exhaust gases). (J.S.)

  6. Environmental optimisation of waste combustion

    Energy Technology Data Exchange (ETDEWEB)

    Schuster, Robert [AaF Energikonsult, Stockholm (Sweden); Berge, Niclas; Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (Sweden)

    2000-12-01

    The regulations concerning waste combustion evolve through R and D and a strive to get better and common regulations for the European countries. This study discusses if these rules of today concerning oxygen concentration, minimum temperature and residence time in the furnace and the use of stand-by burners are needed, are possible to monitor, are the optimum from an environmental point of view or could be improved. No evidence from well controlled laboratory experiments validate that 850 deg C in 6 % oxygen content in general is the best lower limit. A lower excess air level increase the temperature, which has a significant effect on the destruction of hydrocarbons, favourably increases the residence time, increases the thermal efficiency and the efficiency of the precipitators. Low oxygen content is also necessary to achieve low NO{sub x}-emissions. The conclusion is that the demands on the accuracy of the measurement devices and methods are too high, if they are to be used inside the furnace to control the combustion process. The big problem is however to find representative locations to measure temperature, oxygen content and residence time in the furnace. Another major problem is that the monitoring of the operation conditions today do not secure a good combustion. It can lead to a false security. The reason is that it is very hard to find boilers without stratifications. These stratifications (stream lines) has each a different history of residence time, mixing time, oxygen and combustible gas levels and temperature, when they reach the convection area. The combustion result is the sum of all these different histories. The hydrocarbons emission is in general not produced at a steady level. Small clouds of unburnt hydrocarbons travels along the stream lines showing up as peaks on a THC measurement device. High amplitude peaks has a tendency to contain higher ratio of heavy hydrocarbons than lower peaks. The good correlation between some easily detected

  7. Comparaison du filtre adaptatif RIF et du filtre a base de reseau de ...

    African Journals Online (AJOL)

    Comparaison du filtre adaptatif RIF et du filtre a base de reseau de neurones pour le filtrage du courant de reference pour la commande du filtre actif parallele. C Benachaiba, A Bassou, B Mazari ...

  8. Combustion Stratification for Naphtha from CI Combustion to PPC

    KAUST Repository

    Vallinayagam, R.; Vedharaj, S.; An, Yanzhao; Dawood, Alaaeldin; Izadi Najafabadi, Mohammad; Somers, Bart; Johansson, Bengt

    2017-01-01

    This study demonstrates the combustion stratification from conventional compression ignition (CI) combustion to partially premixed combustion (PPC). Experiments are performed in an optical CI engine at a speed of 1200 rpm for diesel and naphtha (RON

  9. Front end of the nuclear fuel cycle; Amont du cycle du combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Leroux, S.; Gueneau, C.; Le Ny, J.; Camel, D.; Drevet, B.; Granier, J.; Doneddo, F.; Roblin, P.; Van Wambeke, C.; Bouty, O.; Michel, N.; Thro, P.U.; Dupuy, P.; Farcage, D.; Schildknecht, J.; Lompre, L.A.; L' Hermite, D.; Comte, M.; Gobert, O.; De Lamare, J

    1999-07-01

    In this chapter of the DCC 1999 scientific report, the following theoretical studies are detailed: condensation and flow of a binary metallic alloy in a two phase domain, a model of gas centrifuge separative performance called TRYPHON, an estimation of electron gun cathodes erosion. It also provides technological developments and instrumentation studies: a power improvement of diode-pumped solid state lasers, measurement using intracavity near resonant propagation in atomic vapours. (A.L.B.)

  10. Back end of the nuclear fuel cycle; Aval du cycle du combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Dognon, J.P.; Rabbe, C.; Beudaert, Ph.; Lamare, V.; Wipff, G.; Moisy, Ph.; Charrin, N.; Blanc, P.; Den Auwer, Ch.; Revel, R.; Charbonnel, M.C.; Presson, M.T.; Cau Dit Coumes, C.; Chopin-Dumas, J.; Devisme, F.; Rat, B.; Hill, C.; Guillaneux, D.; Madic, C.; Carrera, A.; Dozol, J.F.; Rouquette, H.; Allain, F.; Virelizier, H.; Moulin, Ch.; Lemort, F.; Orlhac, X.; Fillet, C.; Carpena, J.; Advocat, T.; Leturcq, G.; Lacombe, J.; Bonnetier, A.; Ribet, I.; Poitou, S.; Richaud, D.; Fiquet, O.; Gramondi, P.; Massit, H.; Meyer, D.; Conocar, O.; Pettier, J.L.; Raphael, T.; Bouniol, P.; Sercombe, J.; Badouix, P.; Adenot, F.; Le Bescop, P.; Mazoin, C.; Motellier, S.; Charles, Y.; Richet, C.; Ayache, R.; Pitsch, H.; Ly, J.; Beaucaire, C.; Devol-Brown, I.; Libert, M.F.; Besnainou, B

    1999-07-01

    In this chapter of the DCC 1999 scientific report, the following theoretical studies are detailed: electronic structure of lanthanides or actinides complexes, forecasting of the stoichiometry of europium nitrate complexes, actinides aqueous solutions analytical and thermodynamical chemistry, actinides complexes structural determination. It also provides experimental studies: actinides and lanthanides separation, radioactive wastes processing and conditioning, plasma torch vitrification process, simulation of the wastes packages characterization, wastes storage with concrete behaviour and biodegradation. (A.L.B.)

  11. Laser-induced multi-point ignition for enabling high-performance engines

    KAUST Repository

    Chung, Suk-Ho

    2015-01-01

    Various multi-point laser-induced ignition techniques were reviewed, which adopted conical cavity and prechamber configurations. Up to five-point ignitions have been achieved with significant reduction in combustion duration, demonstrating potential increase in combustion system efficiency.

  12. Le ministre du Commerce international du Canada rencontre des ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    17 juil. 2017 ... La promotion de l'entrepreneuriat, la façon dont le commerce peut profiter aux femmes et à leur famille, et la création d'emplois pour les plus vulnérables étaient au coeur de la discussion en table ronde du ministre du Commerce international du Canada, l'honorable François-Philippe Champagne, et des ...

  13. EPA/IFP EUROPEAN WORKSHOP ON THE EMISSION ON NITROUS OXIDE FROM FOSSIL FUEL COMBUSTION

    Science.gov (United States)

    The report summarizes the proceedings of an EPA/Institut Francais du Petrole (IFP) cosponsored workshop addressing direct nitrous oxide (N2O) emission from fossil fuel combustion. The third in a series, it was held at the IFP in Rueil-Malmaison, France, on June 1-2, 1988. Increas...

  14. Strobes: An oscillatory combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; Lingen, J.N.J. van; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the

  15. Catalytically enhanced combustion process

    International Nuclear Information System (INIS)

    Rodriguez, C.

    1992-01-01

    This patent describes a fuel having improved combustion efficiency. It comprises a petroleum based liquid hydrocarbon; and a combustion catalyst comprising from about 18 to about 21 weight percent naphthalene, from about 75 to about 80 weight percent toluene, and from about 2.8 to about 3.2 weight percent benzyl alcohol

  16. Fifteenth combustion research conference

    International Nuclear Information System (INIS)

    1993-01-01

    The BES research efforts cover chemical reaction theory, experimental dynamics and spectroscopy, thermodynamics of combustion intermediates, chemical kinetics, reaction mechanisms, combustion diagnostics, and fluid dynamics and chemically reacting flows. 98 papers and abstracts are included. Separate abstracts were prepared for the papers

  17. Study of atmospheric emissions from liquid and solid fuels burning facilities and from raw phosphate chemical treatment in Sfax City (Tunisia); Etude des residus de combustion des fuels liquide et solide et de traitement chimique du phosphate brut dans la ville de Sfax (Tunisie)

    Energy Technology Data Exchange (ETDEWEB)

    Azri, Ch; Tili, A.; Serbaji, M.M. [Faculte des Sciences de Sfax, Dept. des Sciences de la Terre, Sfax (Tunisia); Medhioub, K. [Institut Preparatoire aux Etudes d' Ingenieurs de Sfax (IPEIS), Sfax (Tunisia)

    2002-07-01

    Study of atmospheric emissions from solid and liquid fuels burning facilities and from chemical treatment processes of raw phosphate in Sfax City (Tunisia) shows different forms of pollution concerning mainly sulfur oxides (SO{sub x}), sulfuric and phosphoric acid mists, fluorinated compounds and dust. Limited performances of amortized and/or over used de-pollution systems can explain high atmospheric emissions above emission limits. Gaseous pollution has been shown as coming mainly from phosphate treatment processes inside the chemical complex 'SIAPE' while particulate pollution is coming from all specific industries (SIAPE, charcoal facilities and weaving and soap factories). Calculated emission factors of these industries for some heavy metals (Pb, Cd, Ni, Cu, Zn) are very different. They are ranging from 0.3 to 9.5 g/t for phosphate treatment residues. Excepted Ni with 15.5 g/t, they are rather small for heavy fuels combustion residues. It, nevertheless, exceeds the emission factor of Ni for the phosphate treatment process. Volumes of emissions and calculated annual fluxes of metals are showing that 'SIAPE' could be a potential source of atmospheric pollution in the city. Its contribution to metal emissions is really exceeding emissions from well identified heavy fuels burning facilities in the city. Just to compare, Ni emissions from its processes are equal to emissions from 38 heavy fuels burning facilities of 4.8 t/day capacity (Ni 1 046 kg/year instead of 27 kg/year). Such a fact is clearly pointing out the high level of anthropogenic pollution from chemical processes adopted for primary matter transformation. They hence should be fitted with suitable de-pollution systems. (authors)

  18. Portage vaginal du streptocoque du groupe B chez la femme ...

    African Journals Online (AJOL)

    Introduction: le streptocoque du groupe B est le principal agent impliqué dans les infections materno-fœtales, les septicémies et les méningites du nouveau-né à terme. L'objectif est de déterminer le taux de portage maternel du streptocoque du groupe B (SGB) à terme. Méthodes: un prélèvement vaginal a été réalisé de ...

  19. CHOEUR DU CERN

    CERN Multimedia

    CHOEUR DU CERN

    2010-01-01

    Les répétitions du chœur du CERN reprendront le mercredi 15 septembre à 20.00 heures à l’amphithéâtre principal – bâtiment 500. Au programme la préparation de notre concert de Noël avec la Missa Brevis, KV115, de Léopold Mozart et de la musique de Noël d’Europe. Les personnes qui aiment chanter, notamment des sopranes et des ténors, sont les bienvenues. Pour tout contact s’adresser à : Baudouin Bleus - (tél.CERN 767 82 44) -(baudouin.bleus@cern.ch) ou Martin Gatehouse ( martin.gatehouse@wanadoo.fr) ou Jean-Paul Diss (jean-pauldiss@wanadoo.fr).  

  20. Hepatiques du Surinam

    NARCIS (Netherlands)

    Jovet-Ast, S.

    1957-01-01

    Il n’existe pas, actuellement, de catalogue des Hépatiques du Surinam. Les Hépatiques de ce pays restent très peu connues. Cependant, certaines ont attiré l’attention des Bryologues et ont été citées dans quelques ouvrages anciens ou récents. Je ne ferai pas ici une révision complète de ces

  1. (l.) Medik du Maroc

    African Journals Online (AJOL)

    PR BOKO

    Résumé. Dipcadi serotinum (L.) Medik, est une plante de la famille des Hyacinthaceae, elle est largement utilisée comme réchauffant et aussi pour combattre la jaunisse. Cette plante trouve une large utilisation par la population de la région côtière du Maroc. À notre connaissance l'huile essentielle de cette espèce n'a ...

  2. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-08-17

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  3. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-01-01

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  4. Bibliographical study for the development of an electrochemical preparation of plutonium molten salts; Etude bibliographique en vue de la mise au point d'une preparation electrochimique en sels fondus du plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Lefevre, J.

    1957-01-15

    Based on an analogy with methods of electrochemical preparation of uranium molten salts, this bibliographical study reports data of physical properties of plutonium (melting point, density, ranges of existence of the different plutonium phases, resistivity, resistivity variation coefficient), discusses the search for an electrolytic bath (properties of plutonium bromides, chlorides and fluorides), and the required apparatus (an electrolysis cell)

  5. PDF Modeling of Turbulent Combustion

    National Research Council Canada - National Science Library

    Pope, Stephen B

    2006-01-01

    .... The PDF approach to turbulent combustion has the advantages of fully representing the turbulent fluctuations of species and temperature, and of allowing realistic combustion chemistry to be implemented...

  6. La mesure du danger

    CERN Document Server

    Manceron, Vanessa; Revet, Sandrine

    2014-01-01

    La mesure du danger permet d’explorer des dangers de nature aussi diverse que la délinquance, la pollution, l’écueil maritime, la maladie ou l’attaque sorcellaire, l’extinction d’espèces animales ou végétales, voire de la Planète tout entière. Au croisement de la sociologie, de l’anthropologie et de l’histoire, les différents articles analysent les pratiques concrètes de mesure pour tenter de comprendre ce qui se produit au cours de l’opération d’évaluation du danger sans préjuger de la nature de celui-ci. L’anthropologie a contribué à la réflexion sur l’infortune en s’intéressant aux temporalités de l’après : maladies, catastrophes, pandémies, etc. et en cherchant à rendre compte de l’expérience des victimes, de leur vie ordinaire bouleversée, de la recomposition du quotidien. Elle s’intéresse aussi aux autres types de mesures, les savoirs incorporés, qui reposent sur l’odorat, la vue ou le toucher et ceux qui ressortent d’une épistémologie « non ...

  7. Fluidized bed combustion: mixing and pollutant limitation

    Energy Technology Data Exchange (ETDEWEB)

    Leckner, B. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Energy Conversion

    1997-10-01

    Fluidized bed combustion (FBC) has been applied commercially during a few decades, and sufficient knowledge is gained to design boilers with sizes of up to several hundreds of megawatt thermal power (MW{sub th}). The knowledge of what goes on inside a large combustion chamber is still limited, however, and this impedes further optimization and efficient solution of problems that might occur. Despite this lack of knowledge the present survey deals with combustion chamber processes and discusses mixing and distribution of fuel and air in the combustion chamber and its importance for sulphur capture and reduction of emissions of nitrogen oxides. It is desirable to present the material in a general way and to cover the entire field of FBC. However, the scarce openly published information deals mostly with coal combustion in atmospheric circulating fluidized bed (CFB) combustors, and therefore this application will receive most attention, but reference is also made to pressurized combustion and to other fuels than coal. In this context the important work made in the LIEKKI project on the analysis of different fuels and on the influence of pressure should be especially pointed out. (orig.)

  8. A Physics and Tabulated Chemistry Based Compression Ignition Combustion Model: from Chemistry Limited to Mixing Limited Combustion Modes Un modèle de combustion à allumage par compression basé sur la physique et la chimie tabulée : des modes de combustion contrôlés par la chimie jusqu’aux modes contrôlés par le mélange

    Directory of Open Access Journals (Sweden)

    Bordet N.

    2011-11-01

    modèle de combustion de diffusion est basé sur l’évaluation d’une fréquence de mélange qui est fonction du taux de turbulence dans la chambre et fonction de la masse de carburant vapeur disponible. Ce modèle de combustion est l’un des sous-modèles inclus dans le modèle thermodynamique de chambre de combustion basé sur une approche 2 zones différentiant gaz frais et gaz brûlés. De plus, un sous-modèle concernant la multi-injection a été développé pour prendre en compte les interactions entre les jets et pour décrire l’impact de la multi-injection sur le mélange air/carburant. Les résultats numériques ont été comparés aux mesures réalisées sur un moteur Diesel Renault de 2 litres. Pour l’ensemble des points de fonctionnement explorés, une bonne correspondance a été obtenue entre les résultats issus des simulations et les mesures expérimentales.

  9. Autour du paradigme d’écotourisme

    Directory of Open Access Journals (Sweden)

    Anne-Laure Transler

    2008-02-01

    Full Text Available L’écotourisme ouvre un cadre conceptuel original qui permet d’envisager des démarches renouvelées de développement à partir des revenus issus de consommations touristiques mieux réfléchies et organisées, susceptibles de soutenir des initiatives de développement local s’inscrivant dans un projet global de développement durable. Variante douce du tourisme, loin du tourisme de masse, le champ de l’écotourisme s’étend aux confins du tourisme de nature, du tourisme culturel et des pratiques scientifiques et sportives de plein air. Une définition de l’écotourisme peut être proposée à partir des six points suivants : 1/ nature et culture, 2/ le bien-être des sociétés hôtes, 3/ des touristes responsables, 4/ la participation des sociétés hôtes, 5/ la durabilité, 6/ l’art de la rencontre.Ecotourism provides an original conceptual framework that enables approaches to development that are better able to provide a more equitable distribution of income, as well as better organized and thought through initiatives which are more likely to promote a holistic sustainable local development. With somewhat less negative impact than normal tourism, considerably less that mass tourism, ecotourism can encompass nature tourism, cultural tourism, scientific exploration, and even outdoor sports... A definition of ecotourism should take into account the following six points: 1/ nature and culture, 2/ the welfare of the host community, tourists acting responsibly, 3/ participation by the local community, 5 / sustainability , 6/ promotion of cultural exchanges

  10. Fuel Combustion Laboratory | Transportation Research | NREL

    Science.gov (United States)

    Fuel Combustion Laboratory Fuel Combustion Laboratory NREL's Fuel Combustion Laboratory focuses on designs, using both today's technology and future advanced combustion concepts. This lab supports the combustion chamber platform for fuel ignition kinetics research, was acquired to expand the lab's

  11. Les piles à combustible. Bilan des travaux de recherches. Perspectives Fuel Cells. Review of Research. Outlook

    Directory of Open Access Journals (Sweden)

    Breelle Y.

    2006-11-01

    Full Text Available Cet article fait le point, sous forme résumée, des travaux de recherches et de développement menés par l'Institut Français du Pétrole (IFP depuis vingt ans dans le domaine des piles à combustible : sélection des filières directes conduisant au choix de la pile hydrogène-air basse température à électrolyte basique, mise au point des générateurs à hydrogène alimentés en méthanol. On présente les résultats obtenus et les conclusions des enquêtes effectués dans le domaine des groupes électrogènes et des applications spéciales, dans celui de la traction automobile et dans celui de la production massive d'électricité. This article reviews and sums up the research and development done by Institut Français du Pétrole (IFP in the last 20 years in the field of fuel cells, including the selection of direct methods leading to the choice of low-temperature basic-electrolyte hydrogen/air cells and the development of methanol-powered hydrogen generators. The results obtained are desceibed along with the conclusions of surveys made in the field of electric generators and special applications in the fields of automotive traction and massive electricity production.

  12. Combustion characteristics of crude jatropha oil droplets using rhodium liquid as a homogeneous combustion catalyst

    Science.gov (United States)

    Nanlohy, Hendry Y.; Wardana, I. N. G.; Hamidi, N.; Yuliati, L.

    2018-01-01

    Combustion characteristics of crude jatropha oil droplet at room temperature with and without catalyst have been studied experimentally. Its combustion characteristics have been observed by igniting the oil droplet on a junction of a thermocouple, and the combustion characteristics of oil droplets are observed using a high-speed camera. The results show that the uniqueness of crude jatropha oil as alternative fuel is evidenced by the different stages of combustion caused by thermal cracking in burning droplets. The results also show that the role of the catalyst is not only an accelerator agent, but there are other unique functions and roles as a stabilizer. Moreover, the results also found that the catalyst was able to shorten the ignition timing and burnout time. This phenomenon proves that the presence of catalysts alters and weakens the structure of the triglyceride geometry so that the viscosity and flash point is reduced, the fuel absorbs heat well and flammable.

  13. Second law comparison of oxy-fuel combustion and post-combustion carbon dioxide separation

    International Nuclear Information System (INIS)

    Simpson, Adam P.; Simon, A.J.

    2007-01-01

    To define 2nd law efficiency targets for novel separation technologies, a simplified model of a power plant with two forms of CO 2 capture was developed. In this investigation, oxy-fuel combustion and post-combustion CO 2 separation were compared on an exergetic basis. Using exergy balances and black-box models of power plant components, multiple scenarios were run to determine the impact of plant configuration and separation unit efficiency on overall plant performance. Second law efficiency values from the literature were used to set the baseline performance of various CO 2 separation configurations. Assumed advances in 2nd law efficiency were used to determine the potential for overall system performance improvement. It was found that the 2nd law efficiency of air separation must reach a critical value before the thermodynamics of oxy-fuel combustion become favorable. Changes in operating equivalence ratio significantly move the tipping-point between post-combustion and oxy-fuel strategies

  14. Progress towards phosphorus-33 production: studies on the enrichment of sulphur-33 by means of anion exchangers; Mise au point d'une methode de production du phosphore-33: etudes sur l'enrichissement du soufre-33 au moyen d'echangeurs anioniques; Uspekhi v poluchenii fosfora-33: izuchenie obogashcheniya sery-33 pri pomoshchi anionnykh obmennikov; Progresos on la produccion de fosforo-33: estudios realizados sobre el enriquecimiento del azufre-33 por medio de intercambiadores anionicos

    Energy Technology Data Exchange (ETDEWEB)

    Forberg, S; Westermark, T [Division of Physical Chemistry, Kungl. Tekniska Hogskolan, Stockholm 70 (Sweden)

    1962-01-15

    Enrichment of S{sup 33} by chemical exchange between HSO{sub 3}{sup -} and H{sub 2}SO{sub 3} was selected as the most promising means for P{sup 33} production. HCl displacement of HSO{sub 3}{sup -} from anion exchangers was found to be a convenient method for obtaining counter-current and bulk reflux conditions for this system. Some inherent drawbacks concerning the very high reflux requirements are pointed out. In this institute a plant has been constructed for this process, and the obtained parameters, operation experiences and results are presented. Due to a 'tail' formation of H{sub 2}SO{sub 3} in the displacing HCl, a considerably smaller enrichment than had been calculated from laboratory runs was obtained. Investigations on this problem have been carried out, and a possible way out seems to be the introduction of organic solvents instead of aqueous solutions. (author) [French] L'enrichissement du {sup 33}S par echange chimique entre HSO{sub 3}{sup -} et H{sub 2}SO{sub 3} a ete choisi comme etant le moyen le plus interessant de produire du {sup 33}P. On a constate que l'elution par le HCl du HSO{sub 3}{sup -} fixe par les echangeurs anioniques constituait une methode tres pratique pour realiser les contre-courants et reflux necessaires a cet enrichissement. Les auteurs indiquent quelques inconvenients inherents a la necessite d'obtenir des reflux tres intenses. Une installation speciale a ete construite a l'institut pour realiser ce processus; les auteurs indiquent les parametres observes, les experiences effectuees et les resultats obtenus. Par suite d'une formation de H{sub 2}SO{sub 3} residuairo dans l'eluant HCl, l'enrichissement obtenu etait beaucoup plus faible qu'on ne l'avait calcule d'apres les essais en laboratoire. Les auteurs ont fait des recherches sur ce probleme; il semble possible de remedier a la difficulte en remplacant les solutions aqueuses par des solvants organiques. (author) [Spanish] Los autores han optado por el enriquecimiento del

  15. Conjugated heat transfer and temperature distributions in a gas turbine combustion liner under base-load operation

    International Nuclear Information System (INIS)

    Kim, Kyung Min; Yun, Nam Geon; Jeon, Yun Heung; Lee, Dong Hyun; Cho, Yung Hee

    2010-01-01

    Prediction of temperature distributions on hot components is important in development of a gas turbine combustion liner. The present study investigated conjugated heat transfer to obtain temperature distributions in a combustion liner with six combustion nozzles. 3D numerical simulations using FVM commercial codes, Fluent and CFX were performed to calculate combustion and heat transfer distributions. The temperature distributions in the combustor liner were calculated by conjugation of conduction and convection (heat transfer coefficients) obtained by combustion and cooling flow analysis. The wall temperature was the highest on the attachment points of the combustion gas from combustion nozzles, but the temperature gradient was high at the after shell section with low wall temperature

  16. Construction of the core of the 'heavy water-gas' reactor EL 4; Structures du coeur du reacteur 'eau- lourde-gaz EL 4'

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J L; Foulquier, H; Thome, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    problem of thermal insulation around a zirconium alloy liner tube. The neutron absorption equivalent is about 1, 1 mm of Al, and the mean loss around 2 p. 100 of the thermal power of the reactor. The methods proposed have proved practicable as a result of important research and developments on automatic remote control for all the operations which make up the sequences of mounting, demounting and repairing of the construction components. In particular the possibilities opened up by the new techniques of welding tubes from the inside have been extended to other problems connected with the assembling of a reactor. (authors) [French] Le coeur de ce reacteur est constitue par une cuve contenant l'eau lourde, cuve traversee d'une serie de tubes de force dans lesquels circule le gaz caloporteur sous pression de 60 at. Les specifications de depart qui ont joue un role important dans la conception de ces structures concernent des aspects de securite de fonctionnement (chargement du combustible par les deux faces du reacteur, remplacement des structures sur les deux faces du reacteur), des necessites neutroniques (absorption des structures minimum, pas du reseau, diametre des tubes de force) et des considerations thermiques (temperature de sortie 500 C). Ces specifications ont entraine une disposition horizontale des tubes de force et des problemes d'encombrement tres delicats qui ont elimine (pour les dimensions d'EL 4) toute possibilite de recourir a des compensateurs de dilatation sur les tubes de force. II s'ensuit un dessin de cuve semi-rigide dans lequel les tubes de force contribuent pour une part importante a la resistance mecanique de l'ensemble en jouant le role de tirant, d'ou des contraintes elevees sur les jonctions et tubes de force (et le choix des alliages de zirconium). Les structures comprennent le tube de force, les jonctions, l'isolement thermique et le tube de guidage. On expose brievement les moyens d'essais mis en oeuvre et les performances de ces diverses

  17. Sandia Combustion Research: Technical review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This report contains reports from research programs conducted at the Sandia Combustion Research Facility. Research is presented under the following topics: laser based diagnostics; combustion chemistry; reacting flow; combustion in engines and commercial burners; coal combustion; and industrial processing. Individual projects were processed separately for entry onto the DOE databases.

  18. Archives: les cahiers du cread

    African Journals Online (AJOL)

    Items 1 - 24 of 24 ... Archives: les cahiers du cread. Journal Home > Archives: les cahiers du cread. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. 1 - 24 of 24 Items. 2016 ...

  19. Le commerce du Nord

    OpenAIRE

    Pourchasse, Pierrick; Bouëdec, Gérard Le

    2015-01-01

    Au XVIIIe siècle, la France s'approvisionne abondamment dans les pays du Nord : bois, chanvre et goudron de la Baltique, tonnellerie de Poméranie, pêche de rogue de Norvège, graines de lin de Courlande, barres de fer suédois… Sa balance commerciale est pourtant positive grâce aux sels, aux vins et surtout des nouvelles marchandises coloniales. Or, la plupart des transactions passent par l’incontournable intermédiaire hollandais. Les explications sur l’absence des Français dans le Nord sont re...

  20. La voie du Centre

    OpenAIRE

    2017-01-01

    Après avoir quelque peu louvoyé dans un discours apparemment anarchique où les souvenirs semblent se bousculer sans autre fil conducteur que la référence obsédante au mal satanique, brusquement le narrateur annonce un événement primordial : Foi um fato que se deu, um dia, se abriu. O primeiro. Depois o senhor verá por quê, me devolvendo minha razão (79). Cette introduction situe la rencontre du Menino comme fondatrice d’un destin dont il reviendrait au narrataire de dégager les enchaînements....

  1. Bulletin du CRDI #126

    International Development Research Centre (IDRC) Digital Library (Canada)

    26 févr. 2018 ... Dans ce numéro, découvrez comment la recherche financée par le CRDI permet d'améliorer la santé des mères et des enfants dans les pays du Sud et comment les innovations techniques et sociales de l'initiative SEARCH permettent de surmonter les défis liés à la cybersanté. N'oubliez pas non plus de ...

  2. Shale oil combustion

    International Nuclear Information System (INIS)

    Al-dabbas, M.A.

    1992-05-01

    A 'coutant' carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs

  3. Shale oil combustion

    Energy Technology Data Exchange (ETDEWEB)

    Al-dabbas, M A

    1992-05-01

    A `coutant` carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs.

  4. Indoor combustion and asthma.

    Science.gov (United States)

    Belanger, Kathleen; Triche, Elizabeth W

    2008-08-01

    Indoor combustion produces both gases (eg, nitrogen dioxide, carbon monoxide) and particulate matter that may affect the development or exacerbation of asthma. Sources in the home include both heating devices (eg, fireplaces, woodstoves, kerosene heaters, flued [ie, vented] or nonflued gas heaters) and gas stoves for cooking. This article highlights the recent literature examining associations between exposure to indoor combustion and asthma development and severity. Since asthma is a chronic condition affecting both children and adults, both age groups are included in this article. Overall, there is some evidence of an association between exposure to indoor combustion and asthma, particularly asthma symptoms in children. Some sources of combustion such as coal stoves have been more consistently associated with these outcomes than other sources such as woodstoves.

  5. Sandia Combustion Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, S.C.; Palmer, R.E.; Montana, C.A. (eds.)

    1988-01-01

    During the late 1970s, in response to a national energy crisis, Sandia proposed to the US Department of Energy (DOE) a new, ambitious program in combustion research. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''user facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative-involving US inventories, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions several research projects which have been simulated by working groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship program, supported through the Office of Energy Research, has been instrumental in the success of some of these joint efforts. The remainder of this report presents results of calendar year 1988, separated thematically into eleven categories. Referred journal articles appearing in print during 1988 and selected other publications are included at the end of Section 11. Our traditional'' research activities--combustion chemistry, reacting flows, diagnostics, engine and coal combustion--have been supplemented by a new effort aimed at understanding combustion-related issues in the management of toxic and hazardous materials.

  6. Coke Formation During Hydrocarbons Pyrolysis. Part Two: Methane Thermal Cracking Formation de coke pendant la pyrolyse des hydrocarbures. Deuxième partie : pyrolyse du méthane

    Directory of Open Access Journals (Sweden)

    Billaud F.

    2006-11-01

    Full Text Available Part one of this article dealt with coking in a steam cracking furnace. In this process, coke deposition is a very complex phenomenon due to the number of parameters involved. Nevertheless, for this process, coke deposition is a secondary reaction which does not affect steam cracking yields. It is completely different for methane thermal cracking. Coke is one of the main products of this reaction. Part two of this article deals with coke deposition on the walls of the reactors used for methane thermal cracking. After a brief description of the different set-ups used to study coke deposition, the main parameters involved are listed. The importance of temperature, conversion, type of diluent, and hydrocarbon partial pressure will be enhanced. To conclude, two approaches to the mechanism are proposed to explain coke formation during methane thermal cracking. La première partie de cet article faisait le point sur les réactions indésirables de cokage dans les réacteurs de vapocraquage : dans le cadre de ce procédé, la formation de coke est un phénomène complexe du fait du nombre important de paramètres mis en jeu. Toutefois, pour ce procédé, la réaction de formation du coke à la paroi des réacteurs est une réaction secondaire qui n'affecte pas les rendements de vapocraquage. Ceci est complètement différent dans le cas de la pyrolyse thermique du méthane, procédé pour lequel le coke est un produit principal et indésirable de la réaction. La seconde partie de cet article est consacrée plus particulièrement à la formation du coke, lors de la pyrolyse du méthane et présente les principaux résultats expérimentaux décrits dans la littérature. Parmi les différents montages expérimentaux utilisés pour mesurer le dépôt de coke, il est mentionné, à partir des travaux de la littérature, les 2 techniques suivantes : - la technique de la paroi chaude, - la technique du fil chaud. Pour la première technique, les montages exp

  7. Internal Heterogeneous Processes in Aluminum Combustion

    Science.gov (United States)

    Dreizin, E. L.

    1999-01-01

    This paper discusses the aluminum particle combustion mechanism which has been expanded by inclusion of gas dissolution processes and ensuing internal phase transformations. This mechanism is proposed based on recent normal and microgravity experiments with particles formed and ignited in a pulsed micro-arc. Recent experimental findings on the three stages observed in Al particle combustion in air and shows the burning particle radiation, trajectory (streak), smoke cloud shapes, and quenched particle interiors are summarized. During stage I, the radiation trace is smooth and the particle flame is spherically symmetric. The temperature measured using a three-color pyrometer is close to 3000 K. Because it exceeds the aluminum boiling point (2730 K), this temperature most likely characterizes the vapor phase flame zone rather than the aluminum surface. The dissolved oxygen content within particles quenched during stage I was below the detection sensitivity (about 1 atomic %) for Wavelength Dispersive Spectroscopy (WDS). After an increase in the radiation intensity (and simultaneous decrease in the measured color temperature from about 3000 to 2800 K) indicative of the transition to stage II combustion, the internal compositions of the quenched particles change. Both oxygen-rich (approx. 10 atomic %) and oxygen-lean (combustion behavior and the evolution of its internal composition, the change from the spherically symmetric to asymmetric flame shape occurring upon the transition from stage I to stage II combustion could not be understood based only on the fact that dissolved oxygen is detected in the particles. The connection between the two phenomena appeared even less significant because in earlier aluminum combustion studies carried in O2/Ar mixtures, flame asymmetry was not observed as opposed to experiments in air or O2/CO mixtures. It has been proposed that the presence of other gases, i.e., hydrogen, or nitrogen causes the change in the combustion regime.

  8. Choeur du CERN : Concert

    CERN Multimedia

    CERN Choir

    2017-01-01

    Une œuvre à découvrir! La grande Missa pro defunctis de François-Joseph Gossec (1734-1829) est le chef-d’œuvre tôt venu (à vingt-cinq ans) d’un compositeur qui vivra encore 70 ans après sa création. Elle a connu la gloire, puis s’est fait un peu oublier. Pas du tout le monde cependant : des musicologues ont montré ce que le Requiem de Mozart lui devait ; et il suffit de l’avoir entendue pour comprendre pourquoi Berlioz (qui avait vingt-six ans à la mort de Gossec) en a été impressionné : les nombreux cuivres et bois répartis dans des endroits plus ou moins cachés de la salle de concert pour exprimer les frayeurs du Jugement dernier annoncent son Requiem – et celui de Verdi. Mais « plus encore que par...

  9. Les risques du travail

    CERN Document Server

    Thébaud-Mony, Annie

    2015-01-01

    Depuis les années 1990, les conditions de travail se sont peu à peu imposées dans le débat social. Néanmoins, la situation reste critique. Les risques traditionnels n'ont pas disparu : les manutentions lourdes, l'exposition professionnelle aux cancérogènes, au bruit ou aux vibrations demeurent répandues... De plus, certaines " améliorations " n'ont fait que déplacer et dissimuler les problèmes, telle l'externalisation des risques grâce à la sous-traitance. Dans le même temps, les transformations du travail et des modalités de gestion de la main-d'œuvre ont fragilisé les collectifs et accru l'isolement des salariés, conduisant à une montée visible de la souffrance psychique. Face à ces évolutions, il est plus que jamais nécessaire que tous les acteurs concernés, en particulier les salariés eux-mêmes et leurs représentants, s'approprient les connaissances indispensables pour améliorer la protection de la santé sur les lieux du travail. Tel est le but de ce livre, qui renouvelle int�...

  10. Electrically fired incineration of combustible radioactive waste

    International Nuclear Information System (INIS)

    Charlesworth, D.; Hill, M.

    1985-01-01

    Du Pont Company and Shirco, Inc. are developing a process to incinerate plutonium-contaminated combustible waste in an electrically fired incineration system. Preliminary development was completed at Shirco, Inc. prior to installing an incineration system at the Savannah River Laboratory (SRL), which is operated by Du Pont for the US Department of Energy (DOE). The waste consists of disposable protective clothing, cleaning materials, used filter elements, and miscellaneous materials exposed to plutonium contamination. Incinerator performance testing, using physically representative nonradioactive materials, was completed in March 1983 at Shirco's Pilot Test Facility in Dallas, TX. Based on the test results, equipment sizing and mechanical begin of a full-scale process were completed by June 1983. The full-scale unit is being installed at SRL to confirm the initial performance testing and is scheduled to begin in June 1985. Remote operation and maintenance of the system is required, since the system will eventually be installed in an isolated process cell. Initial operation of the process will use nonradioactive simulated waste. 2 figs., 2 tabs

  11. Shocks in magneto-reactive-gas dynamics with application to the piston problem; Sur les chocs dans un milieu magnetodynamique reactif avec application au probleme du piston

    Energy Technology Data Exchange (ETDEWEB)

    Soubbaramayer, [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-03-01

    This work deals with detonation and deflagration waves in magnetogasdynamics. Four types of detonations and four types of deflagration are considered. We point out that the propagation of these waves is not always completely determined by the initial boundary conditions and the conservation laws across the discontinuity. To fix the ideas we consider the piston problem and we show that in some cases more conditions must be added to the conservation laws in order to provide sufficient data for the unique determination of the propagation process. We then show that the needed additional conditions may be derived from an investigation of the internal structure of the detonation and deflagration process in magneto gas dynamics. This internal structure is investigated for the eight types of process under the influence of the combustion mechanism and the dissipative coefficients (viscosities, electrical and thermal conductivity). Finally all the possible solutions for the piston problem are discussed in a simple case. The methods developed here may be extended to ionizing shocks. (author) [French] On considere dans ce travail les ondes de detonation et de deflagration en magneto-dynamique. Quatre types de detonation et quatre types de deflagration sont etudies. On montre d'abord que la propagation de ces ondes n'est pas toujours completement determinee par les conditions initiales, les conditions aux limites et les conditions de choc. Pour fixer les idees nous considerons le probleme du piston et nous montrons que, dans certains cas, des conditions supplementaires doivent etre jointes aux conditions de choc pour determiner l'ecoulement d'une facon unique. Nous montrons ensuite que ces conditions supplementaires peuvent etre deduites de l'analyse de la structure interne des detonations et des deflagrations magnetodynamiques. Cette structure interne est etudiee en tenant compte du mecanisme de combustion et des coefficients de dissipation (viscosites, conductivites

  12. Experimental study of combustion and emission characteristics of ethanol fuelled port injected homogeneous charge compression ignition (HCCI) combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Maurya, Rakesh Kumar; Agarwal, Avinash Kumar [Engine Research Laboratory, Department of Mechanical Engineering, Indian Institute of Technology Kanpur, Kanpur 208 016 (India)

    2011-04-15

    The homogeneous charge compression ignition (HCCI) is an alternative combustion concept for in reciprocating engines. The HCCI combustion engine offers significant benefits in terms of its high efficiency and ultra low emissions. In this investigation, port injection technique is used for preparing homogeneous charge. The combustion and emission characteristics of a HCCI engine fuelled with ethanol were investigated on a modified two-cylinder, four-stroke engine. The experiment is conducted with varying intake air temperature (120-150 C) and at different air-fuel ratios, for which stable HCCI combustion is achieved. In-cylinder pressure, heat release analysis and exhaust emission measurements were employed for combustion diagnostics. In this study, effect of intake air temperature on combustion parameters, thermal efficiency, combustion efficiency and emissions in HCCI combustion engine is analyzed and discussed in detail. The experimental results indicate that the air-fuel ratio and intake air temperature have significant effect on the maximum in-cylinder pressure and its position, gas exchange efficiency, thermal efficiency, combustion efficiency, maximum rate of pressure rise and the heat release rate. Results show that for all stable operation points, NO{sub x} emissions are lower than 10 ppm however HC and CO emissions are higher. (author)

  13. Calibration of the electromagnetic calorimeter of the Atlas detector: reconstruction of events with non-pointing photons in the frame of a GMSB supersymmetric model; Etalonnage du calorimetre electromagnetique du detecteur Atlas: reconstruction des evenements avec des photons non pointants das le cadre d'un modele supersymetrique GMSB

    Energy Technology Data Exchange (ETDEWEB)

    Prieur, D

    2005-04-15

    The analysis of test-beam data is focused on the calibration of the ATLAS electromagnetic calorimeter. An electrical model has been developed to predict the shape of the physics pulse out of the calibration signal in order to produce optimal filtering coefficients. They are used to compute energy while minimizing electronic noise and getting rid of any possible time shift. Using these coefficients, the uniformity response is 0.6%, in agreement with the 0.7% global constant term required for the whole calorimeter. The study of non pointing photon is driven by the detection of long lived neutralinos predicted by GMSB SUSY models. A systematic study with a detailed simulation of the ATLAS detector was performed to determine the electromagnetic calorimeter angular resolution for such photons. Results were used to parametrized the detector response and to reconstruct SUSY events from this model. (author)

  14. Jouer du piano

    Directory of Open Access Journals (Sweden)

    Fériel Kaddour

    2011-04-01

    Full Text Available La réflexion s’appuie dans un premier temps sur une opposition entre deux attitudes de pianistes  à l’égard du travail à l’instrument : Gould, qui revendique une séparation d’avec le clavier pour ne privilégier que la lecture; Arrau, dont la technique au contraire vise à « faire corps » avec son piano. L’étude de ces deux démarches d’interprètes conduit à une conclusion croisée : l’abstraction gouldienne n’est rien d’autre qu’un déplacement du jeu vers d’autres instruments (ceux qui servent à la prise de son et au montage de ses enregistrements ; le « faire-corps » hérité de la culture pianistique romantique est plus dialectique que fusionnel, et en cela implique une capacité de mise à distance. A partir de cette double conclusion, on tâche enfin de repenser la place du jeu à l’instrument dans la mise en œuvre d’une interprétation, en interrogeant le dialogue qui s’instaure entre la partition telle qu’elle s’écrit et le geste tel qu’il se joue.Our study leans on an opposition between two pianists' attitudes about their work with the instrument. Gould claims a necessary separation from the keyboard in order to prioritize reading. Arrau, on the contrary, relies on a technique which consists in “being one” with his piano. The analysis of these two interprets’ behaviours leads to a crossed conclusion: the gouldian abstraction is nothing else than a displacement of the playing towards another kind of instruments, the ones he uses in sound recording and cut up; Arrau’s “being one” is more dialectic than at first sight, and it therefore implies a real distancing from the piano. This constatation leads to rethink the place of the piano playing in the setting of an interpretation, and to highlight the real dialogue which develops itself between the score as it has been written and the gesture as it is played.

  15. Deliberations of the 29. of December 2010 bearing opinion of the order project setting electricity purchase conditions; Deliberation du 29 decembre 2010 portant avis sur le projet d'arrete fixant les conditions d'achat de l'electricite produite par les installations utilisant a titre principal l'energie degagee par la combustion de matieres non fossiles d'origine vegetale ou animale telles que visees au 4 de l'article 2 du decret n 2000-1196 du 6 decembre 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This document reports deliberations of the Energy Regulation Commission about purchase conditions of electricity produced by installations using mainly the energy released by the combustion of vegetal or animal non fossil materials. As this project aims at decreasing by 3,6% the current purchase tariffs, this document discusses the profitability analysis of projects of more than 5 MW for which the projected decrease still leaves some profitability margin. It comments the case of projects from 1 to 5 MW aimed at supplying sawmills with heat, comments the possible adoption of a winter-summer pricing principle and the impact of the tariff structure on public service expenses

  16. Transient flow combustion

    Science.gov (United States)

    Tacina, R. R.

    1984-01-01

    Non-steady combustion problems can result from engine sources such as accelerations, decelerations, nozzle adjustments, augmentor ignition, and air perturbations into and out of the compressor. Also non-steady combustion can be generated internally from combustion instability or self-induced oscillations. A premixed-prevaporized combustor would be particularly sensitive to flow transients because of its susceptability to flashback-autoignition and blowout. An experimental program, the Transient Flow Combustion Study is in progress to study the effects of air and fuel flow transients on a premixed-prevaporized combustor. Preliminary tests performed at an inlet air temperature of 600 K, a reference velocity of 30 m/s, and a pressure of 700 kPa. The airflow was reduced to 1/3 of its original value in a 40 ms ramp before flashback occurred. Ramping the airflow up has shown that blowout is more sensitive than flashback to flow transients. Blowout occurred with a 25 percent increase in airflow (at a constant fuel-air ratio) in a 20 ms ramp. Combustion resonance was found at some conditions and may be important in determining the effects of flow transients.

  17. Combustion and regulation; Combustion et reglementation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This conference was organized after the publication of the French by-law no 2010 relative to combustion installations and to the abatement of atmospheric pollution. Five topics were discussed during the conference: the new regulations, their content, innovations and modalities of application; the means of energy suppliers to face the new provisions and their schedule; the manufacturers proposals for existing installations and the new equipments; the administration control; and the impact of the new measures on exploitation and engineering. Twenty papers and 2 journal articles are reported in these proceedings. (J.S.)

  18. La grammaticalisation du monde.

    Directory of Open Access Journals (Sweden)

    Etienne Pingaud

    2010-01-01

    Full Text Available Ouvrage atypique par le fond comme par la forme, Le devoir et la grâce rend compte du minutieux travail d’élaboration théorique auquel s’attelle Cyril Lemieux depuis plusieurs années. Et le résultat final se veut pour le moins ambitieux : l’auteur propose un système total supposé dépasser d’un même élan le relativisme, le mentalisme, l’universalisme ethnocentrique, l’historicisme, le naturalisme et l’herméneutisme, tout en réconciliant les sciences sociales avec le ...

  19. Le sacre du printemps

    Directory of Open Access Journals (Sweden)

    Denise Pumain

    2002-03-01

    Full Text Available Cybergeo aura six ans en avril : dans la réalité du virtuel, dans l'univers récent et fluctuant de la publication en ligne, cela fait de nous, tout à la fois, des pionniers et des vétérans. De façon plus surprenante, il se trouve que nous sommes aussi uniques : parmi toutes les revues électroniques de sciences sociales, aucune ne combine comme Cybergeo ancienneté, publication exclusivement électronique, liberté d'accès au texte intégral, édition et gestion par des chercheurs, et comité de lec...

  20. Le Brahmane du Komintern

    Directory of Open Access Journals (Sweden)

    Elizabeth Burgos

    2008-01-01

    Full Text Available Le Brahmane du Komintern, largometraje documental del realizador francés Vladimir León, constituye un ejercicio ejemplar de investigación histórica y  de lograda factura de realización. Y, pese a no haber contado con la ayuda de ninguno organismo público, se trata de un ambicioso proyecto que cubre una amplia extensión geográfica que abarca: Estados Unidos, México, Moscú, Berlín, y la India. Gira en torno a una figura que tuvo en su tiempo su hora de gloria. Un bengalí, hijo de braman, la c...

  1. Optimization of fuel cycles: marginal loss values; Optimisation des cycles de combustibles: valeurs marginales des pertes

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J [Commissariat a l' Energie Atomique, 75 - Paris (France); Lasteyrie, B de; Doumerc, J [Compagnie pour l' Etude et la Realisation de Combustibles Atomiques, 75 - Paris (France)

    1965-07-01

    Uranium processing from the pit to the fuel element rod entails metal losses at every step. These losses become more and more expensive with the elaboration of the metal. Some of the uranium must be accepted as definitely lost whilst the rest could be recovered and recycled. The high cost of these losses, whether they are recycled or not, and the fact that the higher the enrichment is the higher their costs are, make it necessary to take them into account when optimizing fuel cycles. It is therefore felt important to determine their most desirable level from an economic point of view at the various nuclear fuel processing stages. However, in France as in some other countries, fissile material production is a state concern, whilst fuel element fabrication is carried out by private enterprise. Optimization criteria and the economic value of losses are therefore different for each of the two links in the fabrication chain. One can try in spite of this to reach an optimum which would conform to public interest, without interfering with the firm's sales policy. This entails using the fact that for a given output marginal costs are equal at the optimum. One can therefore adjust the level of the losses to attain this equation of marginal costs, as these are easier to obtain from the firm than a justification of the actual prices. One notices moreover that, although mainly concerned with losses, this global analysis can bring both the state and the firm to a better use of other production factors. An account is given of the theory of this economic optimization method and practical applications in the field of natural uranium-graphite moderated and CO{sub 2} cooled reactor fuel element fabrication are offered. (authors) [French] L'elaboration de l'uranium, de la mine a la cartouche d'element combustible, s'accompagne, a tous les stades, de pertes, de plus en plus onereuses, a mesure que le metal devient plus elabore. Une certaine proportion de l'uranium doit etre consideree

  2. (Sorghum bicolor (L.) Moench) du Nord du Burkina Faso

    African Journals Online (AJOL)

    SARAH

    29 déc. 2014 ... sorghos à grains sucrés ont un cycle court et arrivent donc à maturité avant les autres sorghos et le mil d'où leur exploitation comme aliment de soudure par les paysans. L'organisation de la diversité morphologique des accessions de sorghos à grains sucrés du Nord du. Burkina autour principalement des ...

  3. Alimentation du nouveau-ne et du nourrisson dans la region ...

    African Journals Online (AJOL)

    Alimentation du nouveau-ne et du nourrisson dans la region centrale du togo : pratiques familiales et communautaires avant la mise en oeuvre de la strategie « prise en charge integree des maladies de l'enfant »

  4. EQUILIBRE GLYCEMIQUE ET COMPLICATIONS MACROANGIOPATHIQUES DU DIABETE

    Directory of Open Access Journals (Sweden)

    Lyse BORDIER

    2017-05-01

    Full Text Available La question de l’efficacité d’un équilibre glycémique optimal dans la prévention des complications macroangiopathiques du diabète a fait l’objet d’une récente polémique. Si les faits sont clairs pour la microangiopathie notamment au cours du diabète de type 1, ils paraissent moins certains pour les complications cardiovasculaires du diabète de type 2. Cette constatation vient de l’intrication des autres facteurs de risque cardiovasculaires qui sont très fréquents chez ces patients. Cependant, les études de suivi sur une longue durée s’inscrivent en faveur de l’intérêt d’un bon équilibre glycémique sur les complications macroangiopathiques. Les résultats négatifs sur la mortalité de l’étude ACCORD et les inquiétudes concernant la rosiglitazone ont conduit à la mise en place d’études sur la sécurité d’utilisation des nouvelles molécules. Tous ces travaux ont abouti à la démonstration de l’absence de risque des iDPP-4 et de l’effet très positif de certaines molécules de la classe des analogues du GLP-1 et des iSGLT2.Il reste à espérer que la récente mise au point de l’Académie de Médecine soulignant que les complications du diabète de type 2 exigent une prévention multifactorielle qui passe obligatoirement par un contrôle optimisé de l'équilibre glycémique mette fin à une polémique inutile et dangereuse pour nos malades.

  5. Combustible structural composites and methods of forming combustible structural composites

    Science.gov (United States)

    Daniels, Michael A.; Heaps, Ronald J.; Steffler, Eric D.; Swank, W. David

    2013-04-02

    Combustible structural composites and methods of forming same are disclosed. In an embodiment, a combustible structural composite includes combustible material comprising a fuel metal and a metal oxide. The fuel metal is present in the combustible material at a weight ratio from 1:9 to 1:1 of the fuel metal to the metal oxide. The fuel metal and the metal oxide are capable of exothermically reacting upon application of energy at or above a threshold value to support self-sustaining combustion of the combustible material within the combustible structural composite. Structural-reinforcing fibers are present in the composite at a weight ratio from 1:20 to 10:1 of the structural-reinforcing fibers to the combustible material. Other embodiments and aspects are disclosed.

  6. Combustion Sensors: Gas Turbine Applications

    Science.gov (United States)

    Human, Mel

    2002-01-01

    This report documents efforts to survey the current research directions in sensor technology for gas turbine systems. The work is driven by the current and future requirements on system performance and optimization. Accurate real time measurements of velocities, pressure, temperatures, and species concentrations will be required for objectives such as combustion instability attenuation, pollutant reduction, engine health management, exhaust profile control via active control, etc. Changing combustor conditions - engine aging, flow path slagging, or rapid maneuvering - will require adaptive responses; the effectiveness of such will be only as good as the dynamic information available for processing. All of these issues point toward the importance of continued sensor development. For adequate control of the combustion process, sensor data must include information about the above mentioned quantities along with equivalence ratios and radical concentrations, and also include both temporal and spatial velocity resolution. Ultimately these devices must transfer from the laboratory to field installations, and thus must become low weight and cost, reliable and maintainable. A primary conclusion from this study is that the optics-based sensor science will be the primary diagnostic in future gas turbine technologies.

  7. Optical Tomography in Combustion

    DEFF Research Database (Denmark)

    Evseev, Vadim

    spectral measurements at several line-of-sights with a view to applications for tomographic measurements on full-scale industrial combustion systems. The system was successfully applied on industrial scale for simultaneous fast exhaust gas temperature measurements in the three optical ports of the exhaust......D project, it was also important to investigate the spectral properties of major combustion species such as carbon dioxide and carbon monoxide in the infrared range at high temperatures to provide the theoretical background for the development of the optical tomography methods. The new software....... JQSRT 113 (2012) 2222, 10.1016/j.jqsrt.2012.07.015] included in the PhD thesis as an attachment. The knowledge and experience gained in the PhD project is the first important step towards introducing the advanced optical tomography methods of combustion diagnostics developed in the project to future...

  8. Internal combustion engine

    Science.gov (United States)

    Baker, Quentin A.; Mecredy, Henry E.; O'Neal, Glenn B.

    1991-01-01

    An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

  9. Fuel and combustion stratification study of Partially Premixed Combustion

    OpenAIRE

    Izadi Najafabadi, M.; Dam, N.; Somers, B.; Johansson, B.

    2016-01-01

    Relatively high levels of stratification is one of the main advantages of Partially Premixed Combustion (PPC) over the Homogeneous Charge Compression Ignition (HCCI) concept. Fuel stratification smoothens heat release and improves controllability of this kind of combustion. However, the lack of a clear definition of “fuel and combustion stratifications” is obvious in literature. Hence, it is difficult to compare stratification levels of different PPC strategies or other combustion concepts. T...

  10. 1. round table - Spent fuels composition. Back-end of the fuel cycle and reprocessing, plutonium and other nuclear materials management. 2. round table - Separation-transmutation. 3. round table - Scenarios for a long term inventory of nuclear materials and wastes; 1. table ronde - La composition des combustibles uses. L'aval du combustible et le retraitement, la gestion du plutonium et des autres matieres nucleaires. 2. table ronde - Separation-transmutation. 3. table ronde - Scenarii pour un inventaire des matieres et des dechets nucleaires a LT

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    The law from December 30, 1991, precisely defines 3 axes of researches for the management of high level and long-lived radioactive wastes: separation/transmutation, surface storage and underground disposal. A global evaluation report about these researches is to be supplied in 2006 by the French government to the Parliament. A first synthesis of the knowledge gained after 14 years of research has led the national commission of the public debate (CNDP) to organize a national debate about the general options of management of high-level and long-lived radioactive wastes before the 2006 date line. The debate comprises 4 public hearings (September 2005: Bar-le-Duc, Saint-Dizier, Pont-du-Gard, Cherbourg), 12 round-tables (October and November 2005: Paris, Joinville, Caen, Nancy, Marseille), a synthesis meeting (December 2005, Dunkerque) and a closing meeting (January 2006, Lyon). This document is the synthesis of the round table debates which took place at Paris on the reprocessing of spent fuels. Three aspects are discussed: the risks linked with the recovery of valorizable materials, the economical viability of the separation/transmutation option, and the future of the nuclear option in the French energy policy. Six presentations (transparencies) are attached with these proceedings which treat of: the reprocessing/recycling to the test, perspectives of future wastes, present day wastes/valorizable materials and future scenarios, critical analysis scenarios, why reprocessing spent fuels?, processing of spent fuels and recycling, separation and transmutation of long-lived radioactive wastes, thorium-uranium cycle. (J.S.)

  11. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  12. High Gravity (g) Combustion

    Science.gov (United States)

    2006-02-01

    UNICORN (Unsteady Ignition and Combustion with Reactions) code10. Flame propagation in a tube that is 50-mm wide and 1000-mm long (similar to that...turbine engine manufacturers, estimating the primary zone space heating rate. Both combustion systems, from Company A and Company B, required a much...MBTU/atm-hr-ft3) Te m pe ra tu re R is e (K ) dP/P = 2% dP/P = 2.5% dP/P = 3% dP/P = 3.5% dP/P = 4% Company A Company B Figure 13: Heat Release Rate

  13. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani

    2014-10-01

    Alternative transportation fuels, preferably from renewable sources, include alcohols with up to five or even more carbon atoms. They are considered promising because they can be derived from biological matter via established and new processes. In addition, many of their physical-chemical properties are compatible with the requirements of modern engines, which make them attractive either as replacements for fossil fuels or as fuel additives. Indeed, alcohol fuels have been used since the early years of automobile production, particularly in Brazil, where ethanol has a long history of use as an automobile fuel. Recently, increasing attention has been paid to the use of non-petroleum-based fuels made from biological sources, including alcohols (predominantly ethanol), as important liquid biofuels. Today, the ethanol fuel that is offered in the market is mainly made from sugar cane or corn. Its production as a first-generation biofuel, especially in North America, has been associated with publicly discussed drawbacks, such as reduction in the food supply, need for fertilization, extensive water usage, and other ecological concerns. More environmentally friendly processes are being considered to produce alcohols from inedible plants or plant parts on wasteland. While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides ethanol, many linear and branched members of the alcohol family, from methanol to hexanols, have been studied, with a particular emphasis on butanols. These fuels and their combustion properties, including their ignition, flame propagation, and extinction characteristics, their pyrolysis and oxidation reactions, and their potential to produce pollutant emissions have been intensively investigated in dedicated experiments on the laboratory and the engine scale

  14. Combustibility of tetraphenylborate solids

    International Nuclear Information System (INIS)

    Walker, D.D.

    1989-01-01

    Liquid slurries expected under normal in-tank processing (ITP) operations are not ignitible because of their high water content. However, deposits of dry solids from the slurries are combustible and produce dense, black smoke when burned. The dry solids burn similarly to Styrofoam and more easily than sawdust. It is the opinion of fire hazard experts that a benzene vapor deflagration could ignite the dry solids. A tetraphenylborate solids fire will rapidly plug the waste tank HEPA ventilation filters due to the nature of the smoke produced. To prevent ignition and combustion of these solids, the waste tanks have been equipped with a nitrogen inerting system

  15. Studies in combustion dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Koszykowski, M.L. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to develop a fundamental understanding and a quantitative predictive capability in combustion modeling. A large part of the understanding of the chemistry of combustion processes comes from {open_quotes}chemical kinetic modeling.{close_quotes} However, successful modeling is not an isolated activity. It necessarily involves the integration of methods and results from several diverse disciplines and activities including theoretical chemistry, elementary reaction kinetics, fluid mechanics and computational science. Recently the authors have developed and utilized new tools for parallel processing to implement the first numerical model of a turbulent diffusion flame including a {open_quotes}full{close_quotes} chemical mechanism.

  16. Progrès de la connaissance du Congo, du Rwanda et du Burundi de 1993 à 2008

    Directory of Open Access Journals (Sweden)

    Henri Nicolaï

    2013-03-01

    Full Text Available Cette chronique, la vingt et unième d’une série qui a commencé avec l’année 1949, couvre la période 1993-2008 et a pour objectif de faire le point sur les progrès réalisés sur la connaissance du Congo (République démocratique du Congo, du Rwanda et du Burundi, dans le domaine de la géographie mais aussi dans les domaines des sciences naturelles et des sciences humaines qui peuvent fournir des données utiles ou indispensables aux géographes. Chaque référence bibliographique, livre ou article, est accompagnée d’un bref commentaire qui en retient les éléments principaux et surtout les faits ou les idées qui intéressent particulièrement les géographes. L’article comporte onze chapitres dont les plus importants concernent le milieu naturel, la géographie de la santé, la démographie, l’histoire (y compris l’histoire récente, la vie sociale et économique des campagnes traditionnelles et modernes, le secteur informel, les aspects de la vie urbaine. Les événements dramatiques qui se sont produits dans ces territoires africains au cours des quinze dernières années ont rendu la recherche sur le terrain particulièrement difficile tant pour les chercheurs nationaux que pour les chercheurs étrangers, ce qui se traduit notamment par une part de plus en plus importante des recherches menées en milieu urbain.This paper, the 21st issue of an edition of books and paper reviews on the knowledge of three countries of former Belgian Africa (DR Congo, Rwanda, and Burundi, covers the period 1993-2008. A short text for each reference points out the facts or ideas that are useful for geographers. The paper is composed of eleven sections. The most important are coping with the natural environment, health geography, population geography, history (including recent events, social and economic life in traditional and modern rural areas, informal economy, and urban geography. During the last sixteen years, conditions for field

  17. Combustion stratification for naphtha from CI combustion to PPC

    NARCIS (Netherlands)

    Vallinayagam, R.; Vedharaj, S.; An, Y.; Dawood, A.; Izadi Najafabadi, M.; Somers, L.M.T.; Johansson, B.H.

    2017-01-01

    This study demonstrated the change in combustion homogeneity from conventional diesel combustion via partially premixed combustion towards HCCI. Experiments are performed in an optical diesel engine at a speed of 1200 rpm with diesel fuel. Single injection strategy is employed and the fuel is

  18. Materials Control in the Fabrication of Enriched Uranium Fuels; Controle des Matieres au Cours de la Fabrication des Combustibles a Base d'Uranium Enrichi; Uchet materialov pri izgotovlenii topliva na obogashchennom urane; Control de Materiales en la Elaboracion de Combustibles de Uranio Enriquecido

    Energy Technology Data Exchange (ETDEWEB)

    Cardwell, Jr., R. G. [Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    1966-02-15

    measurement were successfully used where alloy fuel content was critical. Scrap handling had an important effect on the materials balance, by which fuel content was confirmed and good accountability was assured. Records and handling procedures, including batching and physical marking methods, were formulated in a manner that assisted the fabricator in criticality control. (author) [French] Grace aux efforts intenses qui ont ete accomplis au cours des 15 dernieres annees dans le domaine de la technologie des elements de combustible par le Laboratoire national d'Oak Ridge, il a ete possible d'etablir des methodes rationnelles de fabrication et de controle des combustibles eraichis, qui trouvent une iaige application dans la fabrication industrielle des elements de combustible a l'heure actuelle. Des techniques eprouvees de manipulation du combustible enrichi en alliages, en dispersion et sous forme d'oxyde en vrac ont ete mises au point et appliquees a l'etude et a la' fabrication des prototypes d'elements combustibles utilises pour le demarrage du reacteur d'essai de materiaux, du reacteur a protection constituee par la masse du ra- lentisseur ou reacteur piscine, du reacteur de puissance transportable construit pat V, du reacteur protection en tour, du reacteur expose a la Conference de Geneve, du reacteur a haut flux pour la production de radioisotopes et du reacteur experimental refroidi par un gaz. L'experience acquise est la base du present memoire qui traite essentiellement des problemes de controle des matieres qui se posent au cours de la fabrication de differents types d'elements de combustible a base d'uranium enrichi et montre comment ils ont ete resolus. Les objectifs principaux d'un systeme rationnel de controle des matieres sont les suivants: 1. reduire le plus possible le nombre des postes matiere a controler; 2. etablir des releves distincts pour chacune des phases principales des operations et les coordonner de maniere a pouvoir relever les ecarts avec un

  19. Toxicology of Biodiesel Combustion products

    Science.gov (United States)

    1. Introduction The toxicology of combusted biodiesel is an emerging field. Much of the current knowledge about biological responses and health effects stems from studies of exposures to other fuel sources (typically petroleum diesel, gasoline, and wood) incompletely combusted. ...

  20. Spectrographic determination of chlorine and fluorine; Dosage du chlore et du fluor par spectrographie d'emission en atmosphere inerte

    Energy Technology Data Exchange (ETDEWEB)

    Contamin, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1965-04-01

    Experimental conditions have been investigated in order to obtain the highest sensitivity in spectrographic determination of chlorine and fluorine using the Fassel method of excitation in an inert atmosphere. The influence of the nature of the atmosphere, of the discharge conditions and of the matrix material has been investigated. The following results have been established: 1. chlorine determination is definitely possible: a working curve has been drawn between 10 {mu}g and 100 {mu}g, the detection limit being around 5 {mu}g; 2. fluorine determination is not satisfactory: the detection limit is still of the order of 80 {mu}g. The best operating conditions have been defined for both elements. (author) [French] Nous avons recherche quelles etaient les conditions permettant d'obtenir la meilleure sensibilite dans le dosage spectrographique du chlore et du fluor par la methode d'excitation en atmosphere inerte (methode de Fassel). Nous avons etudie l'influence de l'atmosphere gazeuse, des conditions de la decharge et du materiau de pastillage. Les points suivants ont ete etablis: 1. le dosage du chlore est possible: une courbe de dosage a ete tracee entre 10 {mu}g et 100 {mu}g et la limite de detection est de l'ordre de 5 {mu}g; 2. le dosage du fluor n'est pas satisfaisant: la limite de detection obtenue etant encore de l'ordre de 80 {mu}g. Les conditions operatoires ont ete precisees pour ces deux elements. (auteur)

  1. Underground treatment of combustible minerals

    Energy Technology Data Exchange (ETDEWEB)

    Sarapuu, E

    1954-10-14

    A process is described for treating oil underground, consisting in introducing several electrodes spaced one from the other in a bed of combustibles underground so that they come in electric contact with this bed of combustibles remaining insulated from the ground, and applying to the electrodes a voltage sufficient to produce an electric current across the bed of combustibles, so as to heat it and create an electric connection between the electrodes on traversing the bed of combustibles.

  2. Le plurilinguisme du perroquet

    Directory of Open Access Journals (Sweden)

    Manuel Mühlbacher

    2012-05-01

    Full Text Available La figure du perroquet occupe une position ambiguë face à la question de la traduction. Il est capable d’imiter des paroles en toutes les langues, mais il n’est capable d’en comprendre aucune — il ne peut que répéter des sons, c’est-à-dire des signifiants. Le traducteur semble faire le contraire quand il passe d’une langue à une autre en tâchant de transmettre une signification semblable par d’autres signes. L’article vise à discuter le rôle du traducteur et sa relation, éventuellement équivoque, au perroquet, en analysant la traduction allemande de Trois Contes par André Stoll et Cora van Kleffens. Un décalage au niveau sémantique peut éclairer l’interprétation du texte, par exemple en explicitant des allusions sous-jacentes, tandis que le transfert de la syntaxe française en allemand pose souvent des problèmes considérables. Comment le traducteur peut-il reproduire des structures syntaxiques qui n’existent pas en allemand, mais qui ne cessent de revenir dans le texte français ? Que faire si le texte se met à jouer au perroquet et finit par se singer lui-même ? André Stoll et Cora van Kleffens ont su trouver des stratégies pour affronter ces difficultés.The figure of the parrot holds an ambiguous position towards the question of translation. It is able to imitate all languages, but it will never understand any of them – its only skill is to mimic sounds, i.e. mere signifiers. On the contrary, the translator seems to be the antithesis of the parrot when he moves from one language to another. He endeavours to convey a similar meaning, but by different signs. The article aims at discussing the role of the translator and his or her eventually equivocal relation to the parrot by means of analysing the German translation of Trois Contes by André Stoll and Cora van Kleffens. Whereas a semantic divergence can result in a different tendency on the level of interpretation, as in the case of an underlying

  3. A Survey of the Fuel Cycles Operated in the United Kingdom; Etude d'ensemble sur les cycles de combustible au Royaume-Uni; Obzor toplivnykh tsiklov, ispol'zuemykh v soedinennom korolevstve; Estudio de los ciclos de combustible utilizados en el Reino Unido

    Energy Technology Data Exchange (ETDEWEB)

    Allday, C. [United Kingdom Atomic Energy Authority, Risley, Warrington, Lancs (United Kingdom)

    1963-10-15

    son programme d'energie d'origine nucleaire sur la filie re des reacteurs a l'uranium naturel et au graphite, refroidis par un gaz. Les reacteurs de Calder Hall et de Chapelcross fonctionnent depuis sept ans; ceux de Berkeley et de Bradwell, qui dependent du Central Electricity Generating Board (CEGB), sont maintenant en service et sept autres reacteurs sont en construction ou en projet. Le combustible destine a ces reacteurs est etudie et fabrique dans l'usine de l'Atomic Energy Authority (AEA) a Springfields, puis transporte jusqu'au reacteur. Apres irradiation et dechargement, le combustible est transporte a l'usine de l'AEA, situee a Windscale, ou l'uranium et le plutonium sont separes des produits de fission. L'auteur decrit l'experience britannique en matiere d'etude et de fabrication du combustible, d'exploitation du reacteur, de transport et de traitement chimique du combustible irradie. Il examine brievement le comportement du combustible dans le reacteur et les differents programmes possibles de chargement et de dechargement, ce sujet etant developpe dans un autre memoire. b) Reacteurs utilisant les combustibles enrichis. Le Royaume-Uni met au point un reacteur perfectionne refroidi par un gaz (Advanced Gas Cooled Reactor = AGR), dont le prototype a ete mis en service en 1963. Le combustible est fabrique a partir d'oxyde d'uranium enrichi gaine d' acier inoxydable; apres irradiation, il sera traite dans une novelle installation qui sera ajoutee a l'usine de separation de Windscale ou est actu ellement traite le combustible gaine de magnox. L'uranium enrichi destine a AGR est produit par l'usine de diffusion situee a Capenhurst. L'oxyde d'uranium naturel enrichi au plutonium peut remplacer, comme combustible, l'oxyde d'uranium enrichi. L'auteur decrit l'experience acquise dans la transformation de l'oxyde destine a AGR et dans le fonctionnement du reacteur et indique comment on envisage de traiter le combustible irradie. Il examine le cas de l'utilisation d

  4. Supersonic Combustion Ramjet Research

    Science.gov (United States)

    2012-08-01

    was in collaboration with Prof. R. Bowersox (Texas A&M University) and Dr. K. Kobayashi ( Japanese Aerospace Exploration Agency, JAXA). 4.2 Ignition... cinema stereoscopic PIV system for the measurement of micro- and meso-scale turbulent premixed flame dynamics,” Paper B13, 5th US Combustion

  5. Infrared monitoring of combustion

    International Nuclear Information System (INIS)

    Bates, S.C.; Morrison, P.W. Jr.; Solomon, P.R.

    1991-01-01

    In this paper, the use of Fourier Transform Infrared (FT-IR) spectroscopy for combustion monitoring is described. A combination of emission, transmission, and reflection FT-IR spectroscopy yields data on the temperature and composition of the gases, surfaces and suspended particles in the combustion environment. Detection sensitivity of such trace exhaust gases as CO, CO 2 , SO 2 , NO x , and unburned hydrocarbons is at the ppm level. Tomographic reconstruction converts line-of-sight measurements into spatially resolved temperature and concentration data. Examples from various combustion processes are used to demonstrate the capabilities of the technique. Industrial measurements are described that have been performed directly in the combustion zone and in the exhaust duct of a large chemical recovery boiler. Other measurements of hot slag show how FT-IR spectroscopy can determine the temperature and optical properties of surfaces. In addition, experiments with water droplets show that transmission FT-IR data yield spectra that characterize particle size and number density

  6. Combustible dust tests

    Science.gov (United States)

    The sugar dust explosion in Georgia on February 7, 2008 killed 14 workers and injured many others (OSHA, 2009). As a consequence of this explosion, OSHA revised its Combustible Dust National Emphasis (NEP) program. The NEP targets 64 industries with more than 1,000 inspections and has found more tha...

  7. Etat Du Magnesium Dans Quelques Sols Sales Du Sud Et Du ...

    African Journals Online (AJOL)

    étude a été réalisée sur 86 échantillons de sols provenant du Centre et du Sud de l´Irak. L\\'expérimentation a consisté, d´une part, à calculer les différents sels dominants dans les sols salés par la méthode de combinaison hypothétique et, ...

  8. Caractérisation des sables et morphologie du fond du lac du ...

    African Journals Online (AJOL)

    Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d\\'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

  9. Caractérisation des sables et morphologie du fond du lac du ...

    African Journals Online (AJOL)

    Administrateur

    Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

  10. Intelligent flame analysis for an optimized combustion

    Energy Technology Data Exchange (ETDEWEB)

    Stephan Peper; Dirk Schmidt [ABB Utilities GmbH, Mainheimm (Germany)

    2003-07-01

    One of the primary challenges in the area of process control is to ensure that many competing optimization goals are accomplished at the same time and be considered in time. This paper describes a successful approach through the use of an advanced pattern recognition technology and intelligent optimization tool modeling combustion processes more precisely and optimizing them based on a holistic view. 17 PowerPoint slides are also available in the proceedings. 5 figs., 1 tab.

  11. Points de vue et lieux touristiques du monde

    Directory of Open Access Journals (Sweden)

    Philippe Violier

    2000-03-01

    Full Text Available Le tourisme international est interprété comme une modalité de la mondialisation qui en révèle les caractères fondamentaux: polarisation au niveau mondial, historicité des disparités spatiales. Au–delà, le tourisme est aussi l'une des trajectoires possibles de l'intégration au monde. Révélés et construits par le tourisme, certains lieux en viennent à se placer dans la hiérarchie mondiale.

  12. Radioimmunodetection of human pancreatic tumor xenografts using DU-PAN II monoclonal antibody

    International Nuclear Information System (INIS)

    Nakamura, Kayoko; Kubo, Atsushi; Hashimoto, Shozo; Furuuchi, Takayuki; Abe, Osahiko; Takami, Hiroshi.

    1988-01-01

    The potential of DU-PAN II, monoclonal antibody (IgM), which was raised against the human tumor cell line, was evaluated for radioimmunodetection of human pancreatic tumors (PAN-5-JCK and EXP-58) grown in nude mice. 125 I-labeled DU-PAN II was accumulated into PAN-5-JCK producing DU-PAN II antigen with a tumor-to-blood ratio of 2.72 ± 3.00, but it did not localize in EXP-58 because of insufficient DU-PAN II. There was no significant uptake of 125 I-nonimmunized IgM in PAN-5-JCK. These facts indicated the specific tumor uptake of DU-PAN II. Excellent images of the tumor PAN-5-JCK were obtained 3 days after the injection of 125 I-DU-PAN II. Gel chromatography was also investigated with respect to the plasma taken from mice injected with antibody, or incubated with antibody in vitro. The results indicate that circulating antigen affected the tumor uptake of DU-PAN II: The more the tumor grew, the higher the amount of antigen excreted into the blood, leading to the degradation of DU-PAN II before it reached the tumor sites. Consequently, the immunoscintigram of the small tumor was remarkably clear. The catabolism and the radiolysis of the labeled IgM injected are critical points in applying immunoscintigraphy. (author)

  13. Le bal du loup

    CERN Multimedia

    Happy Children's Home

    2013-01-01

    The Bord'eau amateur theatre group will graciously perform a play of their creation Le bal du loup Saturday 19 October 2013 at 20:00 Sunday 20 October at 17:00 in the Théâtre des Grottes Rue Louis Favre 43, 1201 Genève Children from age 12 upwards. Summary: The new-elected mayoress of a small village would like to clean up the town by prohibiting alcohol and getting rid of its prostitutes. Then along comes « Massimo Lupo » the pimp... The performances will be given to support the Happy Children's Home charity, which runs a foster-home in Pokhara for Nepali children:  http://www.happychildrenshome.org/ Admission : minimum charge of 10 CHF per person requested, to cover the cost of technical assistance and theatre rental. Any profit will be used solely for the foster-home. At the end of each performance members of the HCH charity will be happy to answer any questions you may have. The theatre has 86 seats, thank you for reserv...

  14. Simulation numérique du transfert de chaleur dans un moteur-fusée à propergol liquide

    Directory of Open Access Journals (Sweden)

    B. KHELIDJ

    2015-03-01

    Full Text Available Ce travail est une contribution à l'étude du refroidissement d'un moteur-fusée à propergol liquide. En effet pour protéger la paroi de la chambre propulsive, un système de refroidissement est nécessaire, car la température des gaz de combustion du propergol liquide dans la chambre de combustion, est très élevée. C'est pour montrer l'intérêt du refroidissement de la paroi de la chambre propulsive qu'une étude de simulation numérique, des phénomènes de combustion et de refroidissement dans la chambre propulsive, a été réalisée en régime permanent à l'aide du code de calcul Fluent. Les résultats de simulation, notamment ceux relatifs aux températures des parois le long de la chambre propulsive ont été confrontés à ceux trouvés dans la littérature.

  15. Combustion control and sensors: a review

    International Nuclear Information System (INIS)

    Docquier, N.; Candel, S.

    2002-01-01

    There is an increased interest in the application of control to combustion. The objective is to optimize combustor operation, monitor the process and alleviate instabilities and their severe consequences. One wishes to improve the system performance, for example by reducing the levels of pollutant emissions or by smoothing the pattern factor at the combustor exhaust. In other cases, the aim is to extend the stability domain by reducing the level of oscillation induced by coupling between resonance modes and combustion. As combustion systems have to meet increasingly more demanding air pollution standards, their design and operation becomes more complex. The trend towards reduced NO x levels has led to new developments in different fields. Automotive engines and gas turbine combustors are considered in this article. In the first case, complex exhaust aftertreatment is being applied and dedicated engine control systems are required to ensure and maintain high pollutant conversion efficiency. For gas turbines, premixed combustors, which operate at lower local temperatures than conventional systems have been designed. In both cases, monitoring and control of the operating point of the process have to be achieved with great precision to obtain the full benefits of the NO x reduction scheme. For premixed combustors operating near the lean stability limit, the flame is more susceptible to blowout, oscillation or flashback. Research is now carried out to reduce these dynamical problems with passive and active control methods. In addition to a broad range of fundamental problems raised by Active Combustion Control (ACC) and Operating Point Control (OPC), there are important technological issues. This paper contains a review of some facets of combustion control and focuses on the sensors that take or could take part to combustion control solutions. The current status of ACC and OPC is presented together with the associated control concepts. The state of the art in sensors is

  16. Low emission internal combustion engine

    Science.gov (United States)

    Karaba, Albert M.

    1979-01-01

    A low emission, internal combustion compression ignition engine having a cylinder, a piston movable in the cylinder and a pre-combustion chamber communicating with the cylinder near the top thereof and in which low emissions of NO.sub.x are achieved by constructing the pre-combustion chamber to have a volume of between 70% and 85% of the combined pre-chamber and main combustion chamber volume when the piston is at top dead center and by variably controlling the initiation of fuel injection into the pre-combustion chamber.

  17. Oxy combustion with CO{sub 2} capture

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-01-15

    An update for oxyfuel-combustion carbon capture in the power industry is provided. The report was developed by the Electric Power Research Institute (EPRI) on behalf of the Global CCS Institute. In the oxyfuel-combustion processes, the bulk nitrogen is removed from the air before combustion. The resulting combustion products will have CO2 content up to about 90 per cent (dry basis). The flue gas impurities (predominantly O2, N2, and Ar) may be removed by reducing the flue gas (at moderate pressure) to a temperature at which the CO2 condenses and the impurities do not. Oxyfuel-combustion may be employed with solid fuels such as coal, petroleum coke, and biomass, as well as liquid and gaseous fuels. Some key points raised in the oxyfuel-combustion carbon capture report are: The oxyfuel-combustion/CO2 capture power plant designs being developed and deployed for service in the next four or five years are based on individual component technologies and arrangements which have demonstrated sufficient maturity, with the greatest remaining technical challenge being integrating the systems into a complete steam-electric power plant; By its nature, an oxyfuel-coal power plant is likely to be a 'near zero' emitter of all criteria pollutants; Existing air-fired power plants might be retrofitted with an air separation unit, oxyfuel-fired burners, flue gas recycle, and a CO2 processing unit, with the large fleet of air-fired power plants in service calling for more study of this option; and, Future efficiency improvements to the oxyfuel-combustion process for power generation point toward an oxyfuel-combustion plant with near zero emissions of conventional pollutants, up to 98 per cent CO2 capture, and efficiency comparable to the best power plants currently being built.

  18. Hydrogen assisted diesel combustion

    Energy Technology Data Exchange (ETDEWEB)

    Lilik, Gregory K.; Boehman, Andre L. [The EMS Energy Institute, The Pennsylvania State University, University Park, PA 16802 (United States); Zhang, Hedan; Haworth, Daniel C. [Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Herreros, Jose Martin [Escuela Tecnica Superior de Ingenieros Industriales, Universidad de Castilla La-Mancha, Avda. Camilo Jose Cela s/n, 13071 Ciudad Real (Spain)

    2010-05-15

    Hydrogen assisted diesel combustion was investigated on a DDC/VM Motori 2.5L, 4-cylinder, turbocharged, common rail, direct injection light-duty diesel engine, with a focus on exhaust emissions. Hydrogen was substituted for diesel fuel on an energy basis of 0%, 2.5%, 5%, 7.5%, 10% and 15% by aspiration of hydrogen into the engine's intake air. Four speed and load conditions were investigated (1800 rpm at 25% and 75% of maximum output and 3600 rpm at 25% and 75% of maximum output). A significant retarding of injection timing by the engine's electronic control unit (ECU) was observed during the increased aspiration of hydrogen. The retarding of injection timing resulted in significant NO{sub X} emission reductions, however, the same emission reductions were achieved without aspirated hydrogen by manually retarding the injection timing. Subsequently, hydrogen assisted diesel combustion was examined, with the pilot and main injection timings locked, to study the effects caused directly by hydrogen addition. Hydrogen assisted diesel combustion resulted in a modest increase of NO{sub X} emissions and a shift in NO/NO{sub 2} ratio in which NO emissions decreased and NO{sub 2} emissions increased, with NO{sub 2} becoming the dominant NO{sub X} component in some combustion modes. Computational fluid dynamics analysis (CFD) of the hydrogen assisted diesel combustion process captured this trend and reproduced the experimentally observed trends of hydrogen's effect on the composition of NO{sub X} for some operating conditions. A model that explicitly accounts for turbulence-chemistry interactions using a transported probability density function (PDF) method was better able to reproduce the experimental trends, compared to a model that ignores the influence of turbulent fluctuations on mean chemical production rates, although the importance of the fluctuations is not as strong as has been reported in some other recent modeling studies. The CFD results confirm

  19. Effets de la microdose sur la production du niébé, du mil et du ...

    African Journals Online (AJOL)

    Effets de la microdose sur la production du niébé, du mil et du sorgho en fonction la toposéquence. Fatimata Saba, Sibiri Jean Baptiste Taonda, Idriss Serme, Alimata A. Bandaogo, Augustin P. Sourwema, Adama Kabre ...

  20. Dynamique des populations du foreur des tiges du cacaoyer ...

    African Journals Online (AJOL)

    SARAH

    30 nov. 2014 ... déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de cacao en. Côte d'ivoire. Méthodologie et résultats : L'étude a été réalisée de 2009 à 2013 dans les plantations villageoises de la région du Haut-Sassandra en Côte d'Ivoire. Les variations des taux d'attaques ...

  1. Dynamique des populations du foreur des tiges du cacaoyer ...

    African Journals Online (AJOL)

    Objectif : Le foreur de tiges du cacaoyer, Eulophonotus myrmeleon Felder cause aujourd'hui d'énormes dégâts dans les cacaoyères ivoiriennes. La présente étude vise à déterminer les périodes de fortes attaques de ce déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de ...

  2. Combustion strategy : United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, D. [Heriot-Watt Univ., Edingburgh, Scotland (United Kingdom). School of Engineering and Physical Sciences

    2009-07-01

    The United Kingdom's combustion strategy was briefly presented. Government funding sources for universities were listed. The United Kingdom Research Councils that were listed included the Arts and Humanities Research Council (AHRC) and the Biotechnology and Biological Sciences Research Council (BBSRC); the Engineering and Physical Sciences Research Council (EPSRC); the Economic and Social Research Council; the Medical Research Council; the Natural Environment Research Council; and the Science and Technology Facilities Council. The EPSRC supported 65 grants worth 30.5 million pounds. The combustion industry was noted to be dominated by three main players of which one was by far the largest. The 3 key players were Rolls-Royce; Jaguar Land Rover; and Doosan Babcock. Industry and government involvement was also discussed for the BIS Technology Strategy Board, strategy technology areas, and strategy application areas.

  3. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T.

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  4. Gestion durable du paysage

    Directory of Open Access Journals (Sweden)

    Jean-David Gerber

    2009-03-01

    Full Text Available Le paysage est de plus en plus perçu comme une ressource. À ce titre, il est nécessaire de trouver des instruments juridiques, politiques ou économiques susceptibles de gérer cette « ressource-paysage » sur le long terme. Le gouvernement suisse a introduit récemment l’instrument des parcs naturels régionaux, organisés selon le modèle français, dans sa législation de protection de la nature et du paysage. Une mise en regard des nouveaux parcs avec des structures de gestion beaucoup plus anciennes, les bourgeoisies et les corporations, permet de mettre en évidence les forces et les faiblesses de chacun de ces instruments dans leur contribution à résoudre les rivalités d’usage entre acteurs utilisant ou influençant la ressource paysage. Cette comparaison permet de formuler des recommandations pratiques concernant la gestion de cette ressource.The landscape is increasingly perceived as a resource. For this reason, it is necessary to find legal, political and economic instruments that will succeed in managing this “resource landscape” in the long term. The Swiss government recently introduced the instrument of regional nature parks into the legislation governing nature and landscape preservation; the proposed parks are organized on the basis of the French model. The examination of the new parks from the perspective of much older management structures, i.e. the civic municipalities (bourgeoisies and corporations, makes it possible to demonstrate the strengths and weaknesses of each of these instruments in their contribution to the resolution of use rivalries between actors who use or influence the resource landscape. This comparison also enables the formulation of practical recommendations regarding the management of this resource.

  5. Plasma Assisted Combustion

    Science.gov (United States)

    2007-02-28

    Tracking an individual streamer branch among others in a pulsed induced discharge J. Phys. D: Appl. Phys. 35 2823--9 [29] van Veldhuizen E M and Rutgers...2005) AIAA–2005–0405. [99] E.M. Van Veldhuizen (ed) Electrical Discharges for Environmental Purposes: Fun- damentals and Applications (New York: Nova...Vandooren J, Van Tiggelen P J 1977 Reaction Mechanism and Rate Constants in Lean Hydrogen–Nitrous Oxide Flames Combust. Flame 28 165 [201] Dean A M, Steiner

  6. Fluid-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, G.; Schoebotham, N.

    1981-02-01

    In Energy Equipment Company's two-stage fluidized bed system, partial combustion in a fluidized bed is followed by burn-off of the generated gases above the bed. The system can be retrofitted to existing boilers, and can burn small, high ash coal efficiently. It has advantages when used as a hot gas generator for process drying. Tests on a boiler at a Cadbury Schweppes plant are reported.

  7. Combustion science and engineering

    CERN Document Server

    Annamalai, Kalyan

    2006-01-01

    Introduction and Review of Thermodynamics Introduction Combustion Terminology Matter and Its Properties Microscopic Overview of Thermodynamics Conservation of Mass and Energy and the First Law of Thermodynamics The Second Law of Thermodynamics Summary Stoichiometry and Thermochemistry of Reacting Systems Introduction Overall Reactions Gas Analyses Global Conservation Equations for Reacting Systems Thermochemistry Summary Appendix Reaction Direction and Equilibrium Introduction Reaction Direction and Chemical Equilibrium Chemical Equilibrium Relations Vant Hoff Equation Adi

  8. Publication du rapport de BSR sur le travail des enfants en Birmanie ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    22 juin 2016 ... Le rapport, intitulé « Child Labor in Myanmar's Garment Sector », a été préparé par Business for Social Responsibility (BSR). Il arrive à point nommé, car les intervenants du monde des affaires sur la scène internationale manifestent un intérêt croissant à l'égard du Myanmar, parallèlement à la levée des ...

  9. Le Developmental Entrepreneurship Program du Massachusetts ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Faire en sorte que les étudiants venant des pays en développement pour étudier au MIT retournent ensuite dans leurs pays respectifs afin d'y concrétiser leurs idées est un souci majeur du MIT, des bailleurs de fonds et du milieu du développement. Ce projet palliera à ce souci en soutenant la formation des fellows du ...

  10. Issues in waste combustion

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Lennart; Robertson, Kerstin; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden); Sundquist, Lena; Wrangensten, Lars [AaF-Energikonsult AB, Stockholm (Sweden); Blom, Elisabet [AaF-Processdesign AB, Stockholm (Sweden)

    2003-05-01

    The main purpose of this review is to provide an overview of the state-of-the-art on research and development issues related to waste combustion with relevance for Swedish conditions. The review focuses on co-combustion in grate and fluidised bed furnaces. It is primarily literature searches in relevant databases of scientific publications with to material published after 1995. As a complement, findings published in different report series, have also been included. Since the area covered by this report is very wide, we do not claim to cover the issues included completely and it has not been possitile to evaluate the referred studies in depth. Basic knowledge about combustion issues is not included since such information can be found elsewhere in the literature. Rather, this review should be viewed as an overview of research and development in the waste-to-energy area and as such we hope that it will inspire scientists and others to further work in relevant areas.

  11. Les dispositifs du Net art

    OpenAIRE

    Fourmentraux, Jean-Paul

    2010-01-01

    La pratique du Net art radicalise la question du potentiel communicationnel d’un média —Internet— qui constitue tout à la fois le support technique, l’outil créatif et le dispositif social de l’œuvre. Les technologies de l’information et de la communication (TIC) placent en effet l’œuvre d’art au cœur d’une négociation socialement distribuée entre l’artiste et le public. L’article est focalisé sur cette construction collective du Net art et sur ses mises en scènes. Il montre le travail artist...

  12. L'administration du travail et la production du droit du travail (1906-1960). : Note de synthèse du rapport de recherche

    OpenAIRE

    Le Crom , Jean-Pierre

    2007-01-01

    Synthèse d'un rapport de recherche dont l'objectif est d'appréhender le rôle de l'administration centrale du travail dans la production du droit du travail. Deux dimensions sont explorées : le profil des rédacteurs et l'organisation des structures.

  13. The Diesel Combustion Collaboratory: Combustion Researchers Collaborating over the Internet

    Energy Technology Data Exchange (ETDEWEB)

    C. M. Pancerella; L. A. Rahn; C. Yang

    2000-02-01

    The Diesel Combustion Collaborator (DCC) is a pilot project to develop and deploy collaborative technologies to combustion researchers distributed throughout the DOE national laboratories, academia, and industry. The result is a problem-solving environment for combustion research. Researchers collaborate over the Internet using DCC tools, which include: a distributed execution management system for running combustion models on widely distributed computers, including supercomputers; web-accessible data archiving capabilities for sharing graphical experimental or modeling data; electronic notebooks and shared workspaces for facilitating collaboration; visualization of combustion data; and video-conferencing and data-conferencing among researchers at remote sites. Security is a key aspect of the collaborative tools. In many cases, the authors have integrated these tools to allow data, including large combustion data sets, to flow seamlessly, for example, from modeling tools to data archives. In this paper the authors describe the work of a larger collaborative effort to design, implement and deploy the DCC.

  14. Internal combustion engine using premixed combustion of stratified charges

    Science.gov (United States)

    Marriott, Craig D [Rochester Hills, MI; Reitz, Rolf D [Madison, WI

    2003-12-30

    During a combustion cycle, a first stoichiometrically lean fuel charge is injected well prior to top dead center, preferably during the intake stroke. This first fuel charge is substantially mixed with the combustion chamber air during subsequent motion of the piston towards top dead center. A subsequent fuel charge is then injected prior to top dead center to create a stratified, locally richer mixture (but still leaner than stoichiometric) within the combustion chamber. The locally rich region within the combustion chamber has sufficient fuel density to autoignite, and its self-ignition serves to activate ignition for the lean mixture existing within the remainder of the combustion chamber. Because the mixture within the combustion chamber is overall premixed and relatively lean, NO.sub.x and soot production are significantly diminished.

  15. « D’abord comprendre, puis apprendre ». À propos des manuels de FLE du point de vue de l’intertextualité // "First to understand, then to learn". french language textbooks form the point of view of intertextuality

    Directory of Open Access Journals (Sweden)

    Alena Prošková

    2015-12-01

    Full Text Available The objective of the following contribution is to present an original point of view on language textbook analyses influenced by approaches commonly applied in the domain of literary science to describing complicated relations which exist between different types of literary texts. Firstly we mention traditional approaches to pedagogic research used in textbook analyses in the Czech education environment and their restrictions. The second part of the contribution focuses on the possible applications of the concept and typology of intertextual (transtextual relations formulated by Gérard Genette in his work Palimpsestes : la Littérature au second degré to the analysis of texts and intertextual relations comprised in language textbooks. Finally we try to show how this approach to textbook analysis can enrich existing textbook research by providing concrete examples from the French language textbook Alter Ego + A2.

  16. Superheated fuel injection for combustion of liquid-solid slurries

    Science.gov (United States)

    Robben, F.A.

    1984-10-19

    A method and device are claimed for obtaining, upon injection, flash evaporation of a liquid in a slurry fuel to aid in ignition and combustion. The device is particularly beneficial for use of coal-water slurry fuels in internal combustion engines such as diesel engines and gas turbines, and in external combustion devices such as boilers and furnaces. The slurry fuel is heated under pressure to near critical temperature in an injector accumulator, where the pressure is sufficiently high to prevent boiling. After injection into a combustion chamber, the water temperature will be well above boiling point at a reduced pressure in the combustion chamber, and flash boiling will preferentially take place at solid-liquid surfaces, resulting in the shattering of water droplets and the subsequent separation of the water from coal particles. This prevents the agglomeration of the coal particles during the subsequent ignition and combustion process, and reduces the energy required to evaporate the water and to heat the coal particles to ignition temperature. The overall effect will be to accelerate the ignition and combustion rates, and to reduce the size of the ash particles formed from the coal. 2 figs., 2 tabs.

  17. Effects of streamwise vortex breakdown on supersonic combustion.

    Science.gov (United States)

    Hiejima, Toshihiko

    2016-04-01

    This paper presents a numerical simulation study of the combustion structure of streamwise vortex breakdown at Mach number 2.48. Hydrogen fuel is injected into a combustor at sonic speed from the rear of a hypermixer strut that can generate streamwise vortices. The results show that the burning behavior is enhanced at the points of the shock waves that are incident on the vortex and therefore the vortex breakdown in the subsonic region occurs due to combustion. The breakdown domain in the mainstream is found to form a flame-holding region suited to combustion and to lead to a stable combustion field with detached flames. In this way, streamwise vortex breakdown has an essential role in combustion enhancement and the formation of flames that hold under supersonic inflow conditions. Finally, the combustion property defined here is shown to coincide with the produced-water mass flow. This property shows that the amount of combustion is saturated at equivalence ratios over 0.4, although there is a slight increase beyond 1.

  18. Formation of Co2P in the combustion regime

    International Nuclear Information System (INIS)

    Muchaik, S.V.; Dubrov, A.N.; Lynchak, K.A.

    1983-01-01

    Combustion of the system Co-P produces the compounds Co 2 P, CoP and CoP 3 , the first two being producible in the combustion regime, while for synthesis of stoichiometric Co 2 P at normal argon pressure, an original mixture with a certain excess of phosphorus is required. The present experiments were performed with electrolytic cobalt powder and red phosphorus. As the Co-P mixture is diluted by the final product (Co 2 P) there is a decrease in combustion temperature and rate, unaccompanied by any of the anomalies seen with dilution by cobalt. It can be suggested that although the combustion in the Co-P system and, possibly, i-- other phosphide systems, is not gasless in its kinetic aspects the combustion mechanism is similar to that in gasless systems. It is shown that formation of the phosphide Co=3''P and specimens wyth composition Co-Co 2 P in the combustion regime occurs with participation of a lIqui] phase of eutectic composition. Combustion occurs in a self-oscillating regime. The temperature for Co 2 P formation is close to its melting point, and the process activation energy comprises 205 kJ/mole

  19. Réflexion sur l’origine du processus de segmentation du marche du travail

    Directory of Open Access Journals (Sweden)

    Attia Nicole

    2006-01-01

    Full Text Available (francuski Ce travail propose une réflexion sur l'origine du processus de segmentation du marché du travail par rapport à l'entreprise. Se situe-t-elle au sein même de l'entreprise ou en amont, c'est à dire entre les entreprises? Cela revient à se demander si on peut avoir une approche microéconomique ou macroéconomique de la segmentation et, à s'interroger sur le rôle réel tenu par les firmes dans le processus. Déterminant pour la théorie, ce rôle est à repenser selon la réponse apportée à notre question.

  20. Ignition system for an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Imhof, G

    1977-05-12

    The invention pertains to ignition systems for internal combustion engines; in particular, these are used in the engines of modern small motorcycles, where power is supplied by means of a so-called flywheel magneto, so that there is no need for an additional battery. The invention will prevent back-kicking. This is achieved by the following means: in the right direction of rotation of the internal combustion engine, due to an axial magnetic unsymmetry of the rotor, a voltage component that can switch the electronic switch will occur only in one of the two parts of the control winding at the point of ignition. In the wrong direction of rotation, on the other hand, this voltage component will only occur in the other part of the control winding and will act in direction on a diode connected in parallel to this part of the winding.

  1. Programme d'immersion du Sustainable Development Policy ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Programme d'immersion du Sustainable Development Policy Institute sur les questions de paix, de violence et de développement. Alors que la paix, la violence et le développement représentent des défis de taille au Pakistan, ils constituent rarement le point de mire pour l'élaboration de politiques. De surcroît, les étudiants ...

  2. Elevage intensif du loup Dicentrarchus labrax

    OpenAIRE

    Coves, Denis; Gasset, Eric

    1993-01-01

    Cet article fait le point sue les coûts de production directs relatifs à différentes méthodes d'élevage intensif du loup (Dicentrarchus labrax). Il s'appuie sur des résultats zootechniques obtenus dans l'unité de démonstration à grande échelle de notre laboratoire. Par rapport à un système de production en circuit ouvert, le recyclage de l'eau permet de diviser par 2.2 les charges directes de production. Si les proies vivantes sont précédemment remplacées par une microparticule efficace, ces ...

  3. evaluation du nouveau ne par cesarienne

    OpenAIRE

    MERAD, Atif Djelloul; BOUARFA, Wahiba

    2014-01-01

    L’étude rétrospective des dossiers montre un recueil des données anamnestiques peu satisfaisant. L’anamnèse reste l’élément essentiel qui permet de faire le point sur l’enfant nouveau-né adressé pour soins appropriés, elle doit retracer l’histoire de la grossesse jusqu’à l’accouchement. L’étude du profil de nos patientes montre que La césarienne concerne particulièrement les primipares qui représentent plus de la moitié de nos femmes. Le risque de césarienne augmente statistiquement lorsqu...

  4. Sulfur Chemistry in Combustion I

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Glarborg, Peter

    2000-01-01

    of the sulphur compounds in fossil fuels and the possibilities to remove them will be given. Then the combustion of sulphur species and their influence on the combustion chemistry and especially on the CO oxidation and the NOx formation will be described. Finally the in-situ removal of sulphur in the combustion...... process by reaction between SO2 and calcium containing sorbents and the influence on the NOx chemistry will be treated....

  5. Oxygen isotopic signature of CO2 from combustion processes

    Directory of Open Access Journals (Sweden)

    W. A. Brand

    2011-02-01

    Full Text Available For a comprehensive understanding of the global carbon cycle precise knowledge of all processes is necessary. Stable isotope (13C and 18O abundances provide information for the qualification and the quantification of the diverse source and sink processes. This study focuses on the δ18O signature of CO2 from combustion processes, which are widely present both naturally (wild fires, and human induced (fossil fuel combustion, biomass burning in the carbon cycle. All these combustion processes use atmospheric oxygen, of which the isotopic signature is assumed to be constant with time throughout the whole atmosphere. The combustion is generally presumed to take place at high temperatures, thus minimizing isotopic fractionation. Therefore it is generally supposed that the 18O signature of the produced CO2 is equal to that of the atmospheric oxygen. This study, however, reveals that the situation is much more complicated and that important fractionation effects do occur. From laboratory studies fractionation effects on the order of up to 26%permil; became obvious in the derived CO2 from combustion of different kinds of material, a clear differentiation of about 7‰ was also found in car exhausts which were sampled directly under ambient atmospheric conditions. We investigated a wide range of materials (both different raw materials and similar materials with different inherent 18O signature, sample geometries (e.g. texture and surface-volume ratios and combustion circumstances. We found that the main factor influencing the specific isotopic signatures of the combustion-derived CO2 and of the concomitantly released oxygen-containing side products, is the case-specific rate of combustion. This points firmly into the direction of (diffusive transport of oxygen to the reaction zone as the cause of the isotope fractionation. The original total 18O signature of the material appeared to have little influence, however, a contribution of specific bio

  6. Pulsating combustion - Combustion characteristics and reduction of emissions

    Energy Technology Data Exchange (ETDEWEB)

    Lindholm, Annika

    1999-11-01

    In the search for high efficiency combustion systems pulsating combustion has been identified as one of the technologies that potentially can meet the objectives of clean combustion and good fuel economy. Pulsating combustion offers low emissions of pollutants, high heat transfer and efficient combustion. Although it is an old technology, the interest in pulsating combustion has been renewed in recent years, due to its unique features. Various applications of pulsating combustion can be found, mainly as drying and heating devices, of which the latter also have had commercial success. It is, however, in the design process of a pulse combustor, difficult to predict the operating frequency, the heat release etc., due to the lack of a well founded theory of the phenomenon. Research concerning control over the combustion process is essential for developing high efficiency pulse combustors with low emissions. Natural gas fired Helmholtz type pulse combustors have been the experimental objects of this study. In order to investigate the interaction between the fluid dynamics and the chemistry in pulse combustors, laser based measuring techniques as well as other conventional measuring techniques have been used. The experimental results shows the possibilities to control the combustion characteristics of pulsating combustion. It is shown that the time scales in the large vortices created at the inlet to the combustion chamber are very important for the operation of the pulse combustor. By increasing/decreasing the time scale for the large scale mixing the timing of the heat release is changed and the operating characteristics of the pulse combustor changes. Three different means for NO{sub x} reduction in Helmholtz type pulse combustors have been investigated. These include exhaust gas recirculation, alteration of air/fuel ratio and changed inlet geometry in the combustion chamber. All used methods achieved less than 10 ppm NO{sub x} emitted (referred to stoichiometric

  7. Studies in Petroleum Composition Development of a Compositional Map for Various Feedstocks Études concernant la composition du pétrole. Mise au point d'une carte de types de constituants appliquée à différentes charges

    Directory of Open Access Journals (Sweden)

    Long R. B.

    2006-11-01

    Full Text Available The composition of petroleum has been the subject of many studies leading to descriptions of petroleum composition in terms of broad generic fractions. The current work shows that petroleum can be described in terms of a mapthat is based upon specific boundaries of the constituent types. For example, an alternate method of describing petroleum composition is to use yields of properties of the various adsorption/elution fractions in the order of increasing polarity of the eluting solvent as a polarity scale. Such endeavors will ultimately lead to a more thorough understanding of composition and behavior as seen through the functional types within petroleum. La composition du pétrole a fait l'objet de nombreuses études permettant de la décrire au moyen de larges fractions génériques. La présente étude montre que la composition du pétrole peut être représentée par une cartebasée sur des frontières, spécifiques de types de constituants. Par exemple, une des méthodes pour décrire la composition du pétrole consiste à utiliser les rendements des propriétés de diverses fractions d'absorbtion/élution en fonction de leur polarité; l'échelle de polarité étant donnée par la polarité des solvants. De tels travaux conduiront finalement à une connaissance plus approfondie de la composition et du comportement du pétrole comme on l'a vu avec les diverses fonctions types dans le pétrole.

  8. Combustion from basics to applications

    CERN Document Server

    Lackner, Maximilian; Winter, Franz

    2013-01-01

    Combustion, the process of burning, is defined as a chemical reaction between a combustible reactant (the fuel) and an oxidizing agent (such as air) in order to produce heat and in most cases light while new chemical species (e.g., flue gas components) are formed. This book covers a gap on the market by providing a concise introduction to combustion. Most of the other books currently available are targeted towards the experienced users and contain too many details and/or contain knowledge at a fairly high level. This book provides a brief and clear overview of the combustion basics, suitable f

  9. Mathematical Modeling in Combustion Science

    CERN Document Server

    Takeno, Tadao

    1988-01-01

    An important new area of current research in combustion science is reviewed in the contributions to this volume. The complicated phenomena of combustion, such as chemical reactions, heat and mass transfer, and gaseous flows, have so far been studied predominantly by experiment and by phenomenological approaches. But asymptotic analysis and other recent developments are rapidly changing this situation. The contributions in this volume are devoted to mathematical modeling in three areas: high Mach number combustion, complex chemistry and physics, and flame modeling in small scale turbulent flow combustion.

  10. Un Nouveau Monde du Savoir

    International Development Research Centre (IDRC) Digital Library (Canada)

    Si les effets de la mondialisation sur l'économie, la politique ou encore les ..... Il souligne l'importance cruciale d'un plan stratégique d'internationalisation, ...... Lors du recrutement de nouveaux professeurs ( lorsque cette situation est ...

  11. rive gauche du fleuve Rimac

    International Development Research Centre (IDRC) Digital Library (Canada)

    tégée du fleuve et les terrains vagues d'une zone industrielle. .... Ces deux diagnostics sont d'importants outils qui contri- bueront à une meilleure planification ... conditions et instruments nécessaires pour améliorer la situation financière des ...

  12. Voorwoord Forward | du Plessis | Lexikos

    African Journals Online (AJOL)

    J.CM.D. du Plessis. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions ...

  13. Charte du Conseil des Gouverneurs

    International Development Research Centre (IDRC) Digital Library (Canada)

    Office 2004 Test Drive User

    7. favoriser des communications ouvertes et franches entre le personnel, la direction ..... de dresser le procès-verbal des réunions du Conseil et de ses comités et de veiller à ce ... et des résultats qu'il obtient, et non de sa gestion quotidienne.

  14. Bases biologiques du comportement social

    CERN Document Server

    Laborit, H

    1994-01-01

    Pour bien comprendre le comportement humain dans un environnement social,il est necessaire de comprendre comment fonctionne le systÂ?me nerveux central. L'une des principales fonctions du cerveau est de crÂ?er des relations entre leshumains.. .................

  15. Suivi de la santé et du bien-être dans la ceinture minière du Goa

    International Development Research Centre (IDRC) Digital Library (Canada)

    Nancy Minogue

    CRDI : Stephanie Colvey. Les contrecoups de la prospérité : En Inde, des chercheurs ont mis au point des outils pour concilier les effets néfastes des activités minières ... et la question du dédommagement des agriculteurs;. • la qualité de l'environnement : les préoccupations relatives à la dégradation de l'air, de l'eau, des ...

  16. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Ziemkiewicz, Paul; Vandivort, Tamara; Pflughoeft-Hassett, Debra; Chugh, Y Paul; Hower, James

    2008-08-31

    Each year, over 100 million tons of solid byproducts are produced by coal-burning electric utilities in the United States. Annual production of flue gas desulfurization (FGD) byproducts continues to increase as the result of more stringent sulfur emission restrictions. In addition, stricter limits on NOx emissions mandated by the 1990 Clean Air Act have resulted in utility burner/boiler modifications that frequently yield higher carbon concentrations in fly ash, which restricts the use of the ash as a cement replacement. Controlling ammonia in ash is also of concern. If newer, “clean coal” combustion and gasification technologies are adopted, their byproducts may also present a management challenge. The objective of the Combustion Byproducts Recycling Consortium (CBRC) is to develop and demonstrate technologies to address issues related to the recycling of byproducts associated with coal combustion processes. A goal of CBRC is that these technologies, by the year 2010, will lead to an overall ash utilization rate from the current 34% to 50% by such measures as increasing the current rate of FGD byproduct use and increasing in the number of uses considered “allowable” under state regulations. Another issue of interest to the CBRC would be to examine the environmental impact of both byproduct utilization and disposal. No byproduct utilization technology is likely to be adopted by industry unless it is more cost-effective than landfilling. Therefore, it is extremely important that the utility industry provide guidance to the R&D program. Government agencies and privatesector organizations that may be able to utilize these materials in the conduct of their missions should also provide input. The CBRC will serve as an effective vehicle for acquiring and maintaining guidance from these diverse organizations so that the proper balance in the R&D program is achieved.

  17. The combustion of sodium

    International Nuclear Information System (INIS)

    Newman, R.N.

    1978-01-01

    The burning rates of sodium in the form of vapour jets, droplets, sprays and unconfined and confined pools have been reviewed. Attention has been paid to assessing the value of models in the various combustion modes. Additional models have been constructed for the descriptions of laminar and turbulent vapour jets, stationary droplets, forced convection over ambient pool fires together with correlations for peak pressures in confined pool environments. Where appropriate experiments with sodium have not been conducted, the likely behaviour is predicted by comparison with the burning of other fuels, particularly in the field of large free ambient fires. Some areas where further knowledge is required are highlighted. (author)

  18. Alternate fuels; Combustibles alternos

    Energy Technology Data Exchange (ETDEWEB)

    Romero Paredes R, Hernando; Ambriz G, Juan Jose [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

    2003-07-01

    In the definition and description of alternate fuels we must center ourselves in those technological alternatives that allow to obtain compounds that differ from the traditional ones, in their forms to be obtained. In this article it is tried to give an overview of alternate fuels to the conventional derivatives of petroleum and that allow to have a clear idea on the tendencies of modern investigation and the technological developments that can be implemented in the short term. It is not pretended to include all the tendencies and developments of the present world, but those that can hit in a relatively short term, in accordance with agreed with the average life of conventional fuels. Nevertheless, most of the conversion principles are applicable to the spectrum of carbonaceous or cellulosic materials which are in nature, are cultivated or wastes of organic origin. Thus one will approach them in a successive way, the physical, chemical and biological conversions that can take place in a production process of an alternate fuel or the same direct use of the fuel such as burning the sweepings derived from the forests. [Spanish] En la definicion y descripcion de combustibles alternos nos debemos centrar en aquellas alternativas tecnologicas que permitan obtener compuestos que difieren de los tradicionales, al menos en sus formas de ser obtenidos. En este articulo se pretende dar un panorama de los combustibles alternos a los convencionales derivados del petroleo y que permita tener una idea clara sobre las tendencias de la investigacion moderna y los desarrollos tecnologicos que puedan ser implementados en el corto plazo. No se pretende abarcar todas las tendencias y desarrollos del mundo actual, sino aquellas que pueden impactar en un plazo relativamente corto, acordes con la vida media de los combustibles convencionales. Sin embargo, la mayor parte de los principios de conversion son aplicables al espectro de materiales carbonaceos o celulosicos los cuales se

  19. Fluidised bed combustion system

    International Nuclear Information System (INIS)

    McKenzie, E.C.

    1976-01-01

    Fluidized bed combustion systems that facilitates the maintenance of the depth of the bed are described. A discharge pipe projects upwardly into the bed so that bed material can flow into its upper end and escape downwardly. The end of the pipe is surrounded by an enclosure and air is discharged into the enclosure so that material will enter the pipe from within the enclosure and have been cooled in the enclosure by the air discharged into it. The walls of the enclosure may themselves be cooled

  20. Tipping Point

    Medline Plus

    Full Text Available ... en español Blog About OnSafety CPSC Stands for Safety The Tipping Point Home > 60 Seconds of Safety (Videos) > The Tipping Point The Tipping Point by ... danger death electrical fall furniture head injury product safety television tipover tv Watch the video in Adobe ...

  1. Positron annihilation in solids: positronium diffusion; Annihilation du positon dans les solides diffusion du positonium

    Energy Technology Data Exchange (ETDEWEB)

    Paulin, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-04-01

    The existence of two slow components in life-time spectrum of positron annihilation in silicium, aluminium and alkaline-earth oxides powders is established. These two long mean-lives {approx_equal} 10{sup -9} s and {approx_equal} 10{sup -7} s result from annihilation, inside and outside the grains respectively, of ortho-positronium formed in defects present in ionic crystals investigated. Dynamic behaviour of Ps, so revealed, is analyzed in terms of diffusion in excellent agreement with experiment. Diffusion constants of the order of 10{sup -4} cm{sup 2} sec{sup -1} and mean path before annihilation from 50 to 300 Angstrom are measured. From 100 to 500 K the temperature influence upon diffusion process is effective only in SiO{sub 2} where activation energy is found about 10{sup -2} eV. The p-Ps zero point energy evaluated by angular correlation gives the order of magnitude for defects dimensions and diffusion mean-time. Finally, o-Ps behaviour in space between grains, where its interaction with atmospheric gases can be only detected, is analysed. (author) [French] Nous mettons en evidence l'existence de deux composantes lentes dans le spectre de temps de vie du positon avant annihilation dans des poudres d'oxydes alcalinoterreux d'alumine et de silice. Ces deux longues vies moyennes {approx_equal} 10{sup -9} s et {approx_equal} 10{sup -7} s resultent respectivement de l'annihilation a l'interieur et a l'exterieur des grains de l'ortho-positonium forme dans certains defauts presents dans les cristaux ioniques etudies. L'analyse des proprietes dynamiques du Ps ainsi revelees, est effectuee en termes de diffusion en excellent accord avec l'experience. Des constantes de diffusion de l'ordre de 10{sup -4} cm{sup 2} sec{sup -1} et des parcours moyens avant annihilation variant de 50 a 300 Angstrom sont ainsi mesures. Entre 100 et 500 K l'influence de la temperature sur le processus de diffusion n'est sensible que dans SiO{sub 2} ou l'energie d'activation est trouvee

  2. Fuel and combustion stratification study of Partially Premixed Combustion

    NARCIS (Netherlands)

    Izadi Najafabadi, M.; Dam, N.; Somers, B.; Johansson, B.

    2016-01-01

    Relatively high levels of stratification is one of the main advantages of Partially Premixed Combustion (PPC) over the Homogeneous Charge Compression Ignition (HCCI) concept. Fuel stratification smoothens heat release and improves controllability of this kind of combustion. However, the lack of a

  3. Combustion Stratification for Naphtha from CI Combustion to PPC

    KAUST Repository

    Vallinayagam, R.

    2017-03-28

    This study demonstrates the combustion stratification from conventional compression ignition (CI) combustion to partially premixed combustion (PPC). Experiments are performed in an optical CI engine at a speed of 1200 rpm for diesel and naphtha (RON = 46). The motored pressure at TDC is maintained at 35 bar and fuelMEP is kept constant at 5.1 bar to account for the difference in fuel properties between naphtha and diesel. Single injection strategy is employed and the fuel is injected at a pressure of 800 bar. Photron FASTCAM SA4 that captures in-cylinder combustion at the rate of 10000 frames per second is employed. The captured high speed video is processed to study the combustion homogeneity based on an algorithm reported in previous studies. Starting from late fuel injection timings, combustion stratification is investigated by advancing the fuel injection timings. For late start of injection (SOI), a direct link between SOI and combustion phasing is noticed. At early SOI, combustion phasing depends on both intake air temperature and SOI. In order to match the combustion phasing (CA50) of diesel, the intake air temperature is increased to 90°C for naphtha. The combustion stratification from CI to PPC is also investigated for various level of dilution by displacing oxygen with nitrogen in the intake. The start of combustion (SOC) was delayed with the increase in dilution and to compensate for this, the intake air temperature is increased. The mixture homogeneity is enhanced for higher dilution due to longer ignition delay. The results show that high speed image is initially blue and then turned yellow, indicating soot formation and oxidation. The luminosity of combustion images decreases with early SOI and increased dilution. The images are processed to generate the level of stratification based on the image intensity. The level of stratification is same for diesel and naphtha at various SOI. When O concentration in the intake is decreased to 17.7% and 14

  4. Les Cahiers du CREAD

    African Journals Online (AJOL)

    Admin

    aux intérêts objectifs de leurs auteurs sans avoir été expressément conçue à cette fin » (Bourdieu P, (1980). Questions de sociologie, éd, Minuit, Paris, p119). De ce point de vue, notre objectif est de proposer une définition opérationnelle propre, touchant ...... les années comme critères de recrutement pour deux différents.

  5. Experimental Design: Application to the Development of a Treatment to Inhibit the Deposition of Barium Sulfate Liable to Be Formed in Enhanced Oil Recovery by Waterflooding Planification d'expériences : application à la mise au point d'un traitement inhibiteur du depôt de sulfate de baryum susceptible de se former en récupération assistée du pétrole par injection d'eau

    Directory of Open Access Journals (Sweden)

    Roque C.

    2006-11-01

    Full Text Available For technical and economic reasons, waterflooding is the most widely-used method in enhanced oil recovery [1]. In many situations, unfortunately, the formation water is incompatible with the injection water. The deposits and corrosion induced by the various reactions of this incompatibility cause irreversible damage, which is especially dangerous for the reservoir rock and the downhole and surface production facilities. This study is concerned exclusively with barium sulfate deposits liable to occur in surface production facilities by the mixing of injection water loaded with sulfate (1300 mg. 1 to the power of (-1 with a formation water with a high barium concentration (1200 mg. 1 to the power of (-1 [2]. Pour des raisons techniques et économiques, l'injection d'eau dans les réservoirs est la méthode la plus employée dans la récupération du pétrole. Malheureusement, dans bien des cas, l'eau en place dans le gisement est incompatible avec l'eau injectée. Les dépôts et les corrosions causés par les diverses réactions physico-chimiques de cette incompatibilité provoquent des dégradations irréversibles particulièrement dangereuses pour les installations de production de fond comme de surface et quelquefois pour la roche réservoir elle-même. Dans le cadre des travaux de recherche relatifs à l'inhibition des dépôts de sulfate sur le champ algérien de Tin Fouyé Tabankort, cette étude a eu pour objectif de sélectionner et d'adapter aux conditions spécifiques de la production un traitement de prévention des dépôts par injection d'un agent inhibiteur. Elle concerne exclusivement les dépôts de sulfate de baryum pouvant apparaître dans les installations de production par mélange d'eau d'injection très chargée en ion sulfate (1300 mg. 1 puissance(-1 avec une eau de gisement très concentrée en élément baryum (1200 mg. 1 puissance(-1. Une méthode expérimentale au laboratoire, faisant appel à des mesures de type

  6. Some Factors Affecting Combustion in an Internal-Combustion Engine

    Science.gov (United States)

    Rothrock, A M; Cohn, Mildred

    1936-01-01

    An investigation of the combustion of gasoline, safety, and diesel fuels was made in the NACA combustion apparatus under conditions of temperature that permitted ignition by spark with direct fuel injection, in spite of the compression ratio of 12.7 employed. The influence of such variables as injection advance angle, jacket temperature, engine speed, and spark position was studied. The most pronounced effect was that an increase in the injection advance angle (beyond a certain minimum value) caused a decrease in the extent and rate of combustion. In almost all cases combustion improved with increased temperature. The results show that at low air temperatures the rates of combustion vary with the volatility of the fuel, but that at high temperatures this relationship does not exist and the rates depend to a greater extent on the chemical nature of the fuel.

  7. Preliminary assessment of combustion modes for internal combustion wave rotors

    Science.gov (United States)

    Nalim, M. Razi

    1995-01-01

    Combustion within the channels of a wave rotor is examined as a means of obtaining pressure gain during heat addition in a gas turbine engine. Several modes of combustion are considered and the factors that determine the applicability of three modes are evaluated in detail; premixed autoignition/detonation, premixed deflagration, and non-premixed compression ignition. The last two will require strong turbulence for completion of combustion in a reasonable time in the wave rotor. The compression/autoignition modes will require inlet temperatures in excess of 1500 R for reliable ignition with most hydrocarbon fuels; otherwise, a supplementary ignition method must be provided. Examples of combustion mode selection are presented for two core engine applications that had been previously designed with equivalent 4-port wave rotor topping cycles using external combustion.

  8. AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

    Science.gov (United States)

    The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

  9. Plasma igniter for internal-combustion engines

    Science.gov (United States)

    Breshears, R. R.; Fitzgerald, D. J.

    1978-01-01

    Hot ionized gas (plasma) ignites air/fuel mixture in internal combustion engines more effectively than spark. Electromagnetic forces propel plasma into combustion zone. Combustion rate is not limited by flame-front speed.

  10. Paul Celan in Translation: "Du sei wie du"

    Directory of Open Access Journals (Sweden)

    John Felstiner

    1983-09-01

    Full Text Available Translating the lyric poetry of Paul Celan, especially his later poems, carries not only the endemic challenge and difficulty of any verse translation, but the added incentive of doing justice to a writer whose whole recourse after the Holocaust—whose sanctuary, if he was to have any at all—he sought in language itself, specifically in the Muttersprache , the mother tongue that was as well the tongue of those who murdered his mother and father. This essay exposes a process of translating "Du sei wie du" (1970, which perhaps more than any other poem by Celan, at once solicits and defies translation, moving as it does from modern to medieval German, and closing with Hebrew words from Isaiah— a messianic imperative that shows Celan verging as ever on his Jewish identity.

  11. Le parcours migratoire de jeunes ruraux du bled du kif

    Directory of Open Access Journals (Sweden)

    Khalid Mouna

    2015-06-01

    Full Text Available Cet article analyse le parcours migratoire des jeunes ruraux originaires des zones de production du cannabis, jeunes qui cherchent à briser les chaînes de soumission et d’humiliation vécues au quotidien. Pour les jeunes concernés par notre étude, la migration constitue un moyen de s’intégrer dans des réseaux transnationaux et ainsi d’entamer une carrière de beznass (commerçant du cannabis. Ce parcours « initiatique » permet à ces jeunes de revenir au bled avec de nouvelles idées, des moyens accrus, et de jouer un rôle actif dans l’économie locale – qui reste pour eux focalisée sur la production de cannabis, cette dernière restant néanmoins officiellement interdite.

  12. Bassins versants du Loup, de la Cagne et du Malvan

    OpenAIRE

    Lepère, Cédric; Lautier, Laurence; Pellegrino, Emmanuel

    2013-01-01

    Identifiant de l'opération archéologique : 8453 Date de l'opération : 2007 (PC) ; 2007 (PI) Inventeur(s) : Lepère Cédric (AUT) ; Lautier Laurence (AUT) ; Pellegrino Emmanuel (AUT) Une campagne de prospection inventaire a été effectuée pendant trois mois, dans les bassins-versants de la Cagne, du Loup et du Malvan qui regroupent les communes de Cagnes-sur-Mer, Villeneuve-Loubet, La Colle-sur-Loup, Saint-Paul-de-Vence, Vence, Saint-Jeannet, Bezaudun, Tourrettes-sur-Loup, Roquefort-les-Pins, Le ...

  13. Manifold methods for methane combustion

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B.; Pope, S.B. [Cornell Univ., Ithaca, NY (United States)

    1995-10-01

    Great progresses have been made in combustion research, especially, the computation of laminar flames and the probability density function (PDF) method in turbulent combustion. For one-dimensional laminar flames, by considering the transport mechanism, the detailed chemical kinetic mechanism and the interactions between these two basic processes, today it is a routine matter to calculate flame velocities, extinction, ignition, temperature, and species distributions from the governing equations. Results are in good agreement with those obtained for experiments. However, for turbulent combustion, because of the complexities of turbulent flow, chemical reactions, and the interaction between them, in the foreseeable future, it is impossible to calculate the combustion flow field by directly integrating the basic governing equations. So averaging and modeling are necessary in turbulent combustion studies. Averaging, on one hand, simplifies turbulent combustion calculations, on the other hand, it introduces the infamous closure problems, especially the closure problem with chemical reaction terms. Since in PDF calculations of turbulent combustion, the averages of the chemical reaction terms can be calculated, PDF methods overcome the closure problem with the reaction terms. It has been shown that the PDF method is a most promising method to calculate turbulent combustion. PDF methods have been successfully employed to calculate laboratory turbulent flames: they can predict phenomena such as super equilibrium radical levels, and local extinction. Because of these advantages, PDF methods are becoming used increasingly in industry combustor codes.

  14. Marche du foncier urbain et promotion du logement au Benin ...

    African Journals Online (AJOL)

    Le marché du foncier urbain au Bénin est un secteur qui met en jeu l'intervention de plusieurs acteurs publics et privés mais également de l'informel. La notion de « foncier urbain » utilisée dans cet article englobe les acceptions et les utilisations faites en architecture, en urbanisme, en aménagement et en gestion urbaine.

  15. Gestion du parc agroforestier du terroir de Vipalogo (Burkina Faso ...

    African Journals Online (AJOL)

    Au Burkina Faso, l'arbre rural fait partie des systèmes de production. Le choix des espèces, leur densité, les modes de gestion ainsi que les besoins à satisfaire, obéissent à des critères propres aux producteurs. C'est pour comprendre ces logiques paysannes de la gestion du parc agroforestier que la présente étude a été ...

  16. Malformations du tube neural en chirurgie pediatrique du chu de ...

    African Journals Online (AJOL)

    encéphalocèle et 6 cas de sipina bifida. La cure chirurgicale a été le principal mode de prise en charge des patients. Seuls 91,38% des cas ont été opérés. Pour toutes les malformations du tube neural, nous avons enregistré 7 décès dont 2 décès ...

  17. Characterisation of metal combustion with DUST code

    Energy Technology Data Exchange (ETDEWEB)

    García-Cascales, José R., E-mail: jr.garcia@upct.es [DITF, ETSII, Universidad Politécnica de Cartagena, Dr Fleming s/n, 30202 Murcia (Spain); Velasco, F.J.S. [Centro Universitario de la Defensa de San Javier, MDE-UPCT, C/Coronel Lopez Peña s/n, 30730 Murcia (Spain); Otón-Martínez, Ramón A.; Espín-Tolosa, S. [DITF, ETSII, Universidad Politécnica de Cartagena, Dr Fleming s/n, 30202 Murcia (Spain); Bentaib, Ahmed; Meynet, Nicolas; Bleyer, Alexandre [Institut de Radioprotection et Sûreté Nucléaire, BP 17, 92260 Fontenay-aux-Roses (France)

    2015-10-15

    Highlights: • This paper is part of the work carried out by researchers of the Technical University of Cartagena, Spain and the Institute of Radioprotection and Nuclear Security of France. • We have developed a code for the study of mobilisation and combustion that we have called DUST by using CAST3M, a multipurpose software for studying many different problems of Mechanical Engineering. • In this paper, we present the model implemented in the code to characterise metal combustion which describes the combustion model, the kinetic reaction rates adopted and includes a first comparison between experimental data and calculated ones. • The results are quite promising although suggest that improvement must be made on the kinetic of the reaction taking place. - Abstract: The code DUST is a CFD code developed by the Technical University of Cartagena, Spain and the Institute of Radioprotection and Nuclear Security, France (IRSN) with the objective to assess the dust explosion hazard in the vacuum vessel of ITER. Thus, DUST code permits the analysis of dust spatial distribution, remobilisation and entrainment, explosion, and combustion. Some assumptions such as particle incompressibility and negligible effect of pressure on the solid phase make the model quite appealing from the mathematical point of view, as the systems of equations that characterise the behaviour of the solid and gaseous phases are decoupled. The objective of this work is to present the model implemented in the code to characterise metal combustion. In order to evaluate its ability analysing reactive mixtures of multicomponent gases and multicomponent solids, two combustion problems are studied, namely H{sub 2}/N{sub 2}/O{sub 2}/C and H{sub 2}/N{sub 2}/O{sub 2}/W mixtures. The system of equations considered and finite volume approach are briefly presented. The closure relationships used are commented and special attention is paid to the reaction rate correlations used in the model. The numerical

  18. Elaboration d’Indice composite de Développement du secteur bovin Laitier (IDL

    Directory of Open Access Journals (Sweden)

    K. KESSAB BELKHAYAT

    2014-03-01

    Full Text Available Plusieurs travaux de recherche ont été publiés sur la mesure du niveau de développement du secteur bovin laitier. Toutefois, aucun de ces travaux ne traite du secteur dans sa globalité. L’objectif du travail est de construire un tableau de bord du secteur bovin laitier à travers le développement d’un indice composite.Pour la construction de l’indice composite, 39 indicateurs du secteur bovin laitier sont identifiés dans le cadre conceptuel couvrant 8 dimensions. La collecte des données a concerné 41 variables composant les indicateurs, 37 pays et sur une période de 11 années (2000-2010. Après le traitement des données manquantes, la base de données complète est constituée de 21 indicateurs, de 23 pays sur 9 années. Un modèle a été développé pour la normalisation, la pondération des indicateurs puis pour le calcul de l’indice composite. Le test de robustesse est déroulé par le calcul du coefficient de corrélation de Pearson. Ce test a montré que de l’indice composite calculé selon 3 méthodes différentes de normalisation et de pondération est robuste. Les pays ont été classés selon leur l’IDL. Plusieurs axes d’analyse sont possibles à travers l’IDL notamment son évolution dans le temps, les points forts et les points faibles pour chaque pays et les leviers de développement du secteur.

  19. Combustion & Laser Diagnostics Research Complex (CLDRC)

    Data.gov (United States)

    Federal Laboratory Consortium — Description: The Combustion and Laser Diagnostics Research Complex (CLRDC) supports the experimental and computational study of fundamental combustion phenomena to...

  20. Development of rapid mixing fuel nozzle for premixed combustion

    International Nuclear Information System (INIS)

    Katsuki, Masashi; Chung, Jin Do; Kim, Jang Woo; Hwang, Seung Min; Kim, Seung Mo; Ahn, Chul Ju

    2009-01-01

    Combustion in high-preheat and low oxygen concentration atmosphere is one of the attractive measures to reduce nitric oxide emission as well as greenhouse gases from combustion devices, and it is expected to be a key technology for the industrial applications in heating devices and furnaces. Before proceeding to the practical applications, we need to elucidate combustion characteristics of non-premixed and premixed flames in high-preheat and low oxygen concentration conditions from scientific point of view. For the purpose, we have developed a special mixing nozzle to create a homogeneous mixture of fuel and air by rapid mixing, and applied this rapidmixing nozzle to a Bunsen-type burner to observe combustion characteristics of the rapid-mixture. As a result, the combustion of rapid-mixture exhibited the same flame structure and combustion characteristics as the perfectly prepared premixed flame, even though the mixing time of the rapid-mixing nozzle was extremely short as a few milliseconds. Therefore, the rapid-mixing nozzle in this paper can be used to create preheated premixed flames as far as the mixing time is shorter than the ignition delay time of the fuel

  1. Numerical and Experimental Study on the Combustion and Emission Characteristics of a Dimethyl Ether (DME Fueled Compression Ignition Engine Études numériques et expérimentales sur les caractéristiques de combustion et d’émissions d’un éther diméthylique (EDM- moteur à auto-allumage rempli de combustible

    Directory of Open Access Journals (Sweden)

    Kim Hyung Jun

    2012-05-01

    Full Text Available A numerical investigation was carried out to study on the combustion and emission characteristics of dimethyl ether (DME with wide ranges of injection timings in compression ignition engines. In order to simulate DME combustion processes, a KIVA-3V code coupled with a chemistry solver was used to solve the detailed chemical kinetics model of DME oxidation. In addition, the Kelvin-Helmholtz-Rayleigh-Taylor (KH-RT hybrid breakup model and Renormalization Group (RNG k-ε  models were applied to analyze the spray characteristics and turbulent flow, respectively. To predict the NOx formation during DME combustion, a reduced Gas Research Institute (GRI NO mechanism was used. From these results on the combustion and emission, the calculated results were compared with experimental ones for the same operating conditions. In the combustion characteristics, the calculated combustion pressure and heat release rates agreed well with experimental results. The levels of experimental NOx emissions was reduced as the start of the injection timing retarded, and also these trends appeared in calculated emission characteristics. Additionally, the calculated CO and HC emissions show an increasing trend as the start of the injection is retarded. Dans cette étude, nous considérons la simulation de la combustion du dimethyl ether (DME dans un moteur à allumage par compression. Les caractéristiques de la combustion ainsi que les émissions polluantes sont analysées sur une large gamme d’avance à l’injection. Afin de simuler le processus de combustion du EDM, le code KIVA-3V couplé à un solveur chimique a été utilisé pour résoudre la cinétique détaillée de l’oxydation du EDM. Le modèle de rupture de Kelvin-Helmholtz-Rayleigh- Taylor (KH-RT ainsi que le modèle de turbulence k-ε  RNG ont été appliqués pour analyser respectivement les caractéristiques du jet et l’écoulement turbulent. Pour prévoir la formation de NOx pendant la combustion

  2. Combustion instability control in the model of combustion chamber

    International Nuclear Information System (INIS)

    Akhmadullin, A N; Ahmethanov, E N; Iovleva, O V; Mitrofanov, G A

    2013-01-01

    An experimental study of the influence of external periodic perturbations on the instability of the combustion chamber in a pulsating combustion. As an external periodic disturbances were used sound waves emitted by the electrodynamics. The purpose of the study was to determine the possibility of using the method of external periodic perturbation to control the combustion instability. The study was conducted on a specially created model of the combustion chamber with a swirl burner in the frequency range from 100 to 1400 Hz. The study found that the method of external periodic perturbations may be used to control combustion instability. Depending on the frequency of the external periodic perturbation is observed as an increase and decrease in the amplitude of the oscillations in the combustion chamber. These effects are due to the mechanisms of synchronous and asynchronous action. External periodic disturbance generated in the path feeding the gaseous fuel, showing the high efficiency of the method of management in terms of energy costs. Power required to initiate periodic disturbances (50 W) is significantly smaller than the thermal capacity of the combustion chamber (100 kW)

  3. Effects of nano-TiO2 on combustion and desulfurization

    International Nuclear Information System (INIS)

    Zhao, Yi; Wang, Shuqin; Shen, Yanmei; Lu, Xiaojuan

    2013-01-01

    Nanosized titanium oxide powder was prepared via the sol–gel process and characterized by transmission electron microscope. The effects of nano-TiO 2 on combustion characteristics of lignite, desulfurization in combustion and the properties of ashes were investigated. The calorific value of coals and the fusion point of the coal ashes were measured by calorimeter and ash fusion point determination meter; the components of coal ashes and the contents of combustible matters in ash were determined by chemical methods; the pore-size distribution and specific surface area of the coal ash were analyzed by surface area analyzer. A thermogravimetric analyzer was used to investigate the effect of nano-TiO 2 on combustion. The results showed that the calorific value of the coal and the fusion temperature of the coal ash were lowered by adding CaO, while on the other hand adding nano-TiO 2 to coal increased the calorific value and the melting temperature effectively. Meanwhile, the coal combustion efficiency and desulfurization in combustion could be effectively improved by the co-action of TiO 2 . - Highlights: • The burn-off rate of coals was raised and the combustible contents were reduced by adding nano-TiO 2 . • The desulfurization in combustion can be achieved by adding CaO, but the combustion efficiency was inhibited. • Nano-TiO 2 can promote the transfer rate of oxygen from gas phase to the surface of char

  4. L’Harmonie du monde

    Directory of Open Access Journals (Sweden)

    Martine Clouzot

    2003-11-01

    Full Text Available La Bourgogne est particulièrement bien présente et représentée dans l’exposition sur la musique et ses représentations au Moyen Âge organisée par Isabelle Marchesin (université de Poitiers, Christine Laloue (conservatrice du Patrimoine au Musée et Martine Clouzot (université de Bourgogne, au Musée de la Musique à Paris du 26 mars au 27 juin 2004. En Côte-d’Or, à Dijon, la Bibliothèque municipale a donné son accord officiel pour le prêt de la Bible d’Etienne Harding, les Moralia in Job et u...

  5. Les vicissitudes du fret ferroviaire

    OpenAIRE

    DABLANC, L

    2010-01-01

    Dans beaucoup de pays européens, et plus encore en Amérique du Nord et en Asie, le transport de marchandises par le train a augmenté depuis dix ans. Cette activité réduit la part des marchandises acheminées par la route et contribue ainsi au développement durable : un camion émet 8 à 30 fois plus de dioxyde de carbone que le train, pour une distance et une quantité transportée équivalentes. Pourtant, la France a raté ce renouveau. Filiale du groupe public SNCF, la Société Fret SNCF, qui assur...

  6. Fixed Points

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 5; Issue 5. Fixed Points - From Russia with Love - A Primer of Fixed Point Theory. A K Vijaykumar. Book Review Volume 5 Issue 5 May 2000 pp 101-102. Fulltext. Click here to view fulltext PDF. Permanent link:

  7. Tipping Point

    Medline Plus

    Full Text Available ... OnSafety CPSC Stands for Safety The Tipping Point Home > 60 Seconds of Safety (Videos) > The Tipping Point ... 24 hours a day. For young children whose home is a playground, it’s the best way to ...

  8. Tipping Point

    Medline Plus

    Full Text Available ... 60 Seconds of Safety (Videos) > The Tipping Point The Tipping Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture head injury product safety television tipover tv Watch the video in Adobe Flash ...

  9. L'energie du moustique

    CERN Document Server

    Augereau, J F

    2002-01-01

    ENSEMBLE DE QUATRE ARTICLES - LARGE HADRON COLLIDER: Le dernier accelerateur de particules du CERN, le LEP, produisait des faisceaux d'electrons de 100 GeV chacun. Le LHC, qui accelere des faisceaux de protons, leur communiquera une energie de 7 TeV chacun. Une energie a la fois colossale et derisoire. Un TeV represente a peu pres l'energie cinetique d'un moustique (1/2 page).

  10. Revision des Symphurus du Siboga

    NARCIS (Netherlands)

    Chabanaud, Paul

    1955-01-01

    Ce m’est un devoir particulièrement agréable que de saisir l’occasion de ce petit mémoire pour remercier M. L. F. DE BEAUFORT, M. H. ENGEL, Directeur du Zoologisch Museum, ainsi que M. J. J. HOEDEMAN de l’accueil qu’à diverses reprises, j’ai reçu de leur part, au Zoölogisch Museum, et aussi des

  11. Space Station Freedom combustion research

    Science.gov (United States)

    Faeth, G. M.

    1992-01-01

    Extended operations in microgravity, on board spacecraft like Space Station Freedom, provide both unusual opportunities and unusual challenges for combustion science. On the one hand, eliminating the intrusion of buoyancy provides a valuable new perspective for fundamental studies of combustion phenomena. On the other hand, however, the absence of buoyancy creates new hazards of fires and explosions that must be understood to assure safe manned space activities. These considerations - and the relevance of combustion science to problems of pollutants, energy utilization, waste incineration, power and propulsion systems, and fire and explosion hazards, among others - provide strong motivation for microgravity combustion research. The intrusion of buoyancy is a greater impediment to fundamental combustion studies than to most other areas of science. Combustion intrinsically heats gases with the resulting buoyant motion at normal gravity either preventing or vastly complicating measurements. Perversely, this limitation is most evident for fundamental laboratory experiments; few practical combustion phenomena are significantly affected by buoyancy. Thus, we have never observed the most fundamental combustion phenomena - laminar premixed and diffusion flames, heterogeneous flames of particles and surfaces, low-speed turbulent flames, etc. - without substantial buoyant disturbances. This precludes rational merging of theory, where buoyancy is of little interest, and experiments, that always are contaminated by buoyancy, which is the traditional path for developing most areas of science. The current microgravity combustion program seeks to rectify this deficiency using both ground-based and space-based facilities, with experiments involving space-based facilities including: laminar premixed flames, soot processes in laminar jet diffusion flames, structure of laminar and turbulent jet diffusion flames, solid surface combustion, one-dimensional smoldering, ignition and flame

  12. Actes des 5èmes Journées Scientifiques du GDR3544 Sciences du Bois. Journées Annuelles du GDR 3544 Sciences du Bois

    OpenAIRE

    CHAPLAIN, Myriam; CARE, Sabine; GRIL, Joseph

    2016-01-01

    Le Groupement de Recherche en Sciences du bois (GDR3544 Sciences du Bois) a été créé en 2012 par le CNRS et renouvelé en 2016 pour 5 ans. La mission de ce groupement est : (1) de structurer la recherche sur le bois en France pour lui donner une visibilité nationale, (2) de contribuer au développement de la formation en sciences du bois et (3) de servir de relai aux réseaux internationaux de sciences du bois. Les 5èmes journées annuelles du GDR Bois ont été organisées à Bordeaux, au domaine du...

  13. Original Paper Performances comparées du HDL-cholestérol et du ...

    African Journals Online (AJOL)

    CT/HDL-C) et du HDL-Cholestérol est le meilleur prédicteur du SMet chez les adultes béninois. .... (Canada) et du. Ministère de la Santé du Bénin. Le consentement éclairé écrit a été obtenu de chaque participant avant leur recrutement dans.

  14. Use of tri-laurylamine during the retreatment of irradiated fuels; Utilisation de la trilaurylamine au retraitement des combustibles irradies

    Energy Technology Data Exchange (ETDEWEB)

    Bathellier, A; Koehly, G; Perez, J J; Chesne, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-07-01

    The purification of aqueous solutions of plutonium can be made by extraction of the Pu (IV) nitrate complex using trilaurylamine in dodecane. The principal physical properties of this solution are considered along with its extractive properties and the influence of foreign ions on the extraction. The application of this method of extraction in a processing cycle for irradiated material is proposed: either for a final purification process or for auxiliary cycles for recovering plutonium from metal production wastes, oxalate precipitation supernatants, or any general aqueous plutonium waste solution. Also proposed are clean-up procedures for regeneration of an extractive solution which has undergone chemical or radiolytic degradation. (authors) [French] La purification du plutonium contenu dans des solutions aqueuses peut etre effectuee par extraction du nitrate de l'ion tetravalent par la trilaurylamine diluee dans du dodecane. Les principales proprietes physiques de ce solvant sont passees en revue ainsi que ses proprietes extractives et l'influence des ions etrangers sur celles-ci. L'application de cette methode d'extraction dans le cycle de traitement des combustibles irradies est envisagee: soit dans le traitement de purification finale, soit dans les cycles annexes ayant trait a la recuperation de plutonium a partir des scories d'elaboration du metal, des eaux-meres oxaliques et d'une facon generale des solutions aqueuses contenant du plutonium. Des traitements de regeneration du solvant ayant subi des degradations chimique ou radiolytique, sont proposes. (auteurs)

  15. Use of tri-laurylamine during the retreatment of irradiated fuels; Utilisation de la trilaurylamine au retraitement des combustibles irradies

    Energy Technology Data Exchange (ETDEWEB)

    Bathellier, A.; Koehly, G.; Perez, J.J.; Chesne, A. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-07-01

    The purification of aqueous solutions of plutonium can be made by extraction of the Pu (IV) nitrate complex using trilaurylamine in dodecane. The principal physical properties of this solution are considered along with its extractive properties and the influence of foreign ions on the extraction. The application of this method of extraction in a processing cycle for irradiated material is proposed: either for a final purification process or for auxiliary cycles for recovering plutonium from metal production wastes, oxalate precipitation supernatants, or any general aqueous plutonium waste solution. Also proposed are clean-up procedures for regeneration of an extractive solution which has undergone chemical or radiolytic degradation. (authors) [French] La purification du plutonium contenu dans des solutions aqueuses peut etre effectuee par extraction du nitrate de l'ion tetravalent par la trilaurylamine diluee dans du dodecane. Les principales proprietes physiques de ce solvant sont passees en revue ainsi que ses proprietes extractives et l'influence des ions etrangers sur celles-ci. L'application de cette methode d'extraction dans le cycle de traitement des combustibles irradies est envisagee: soit dans le traitement de purification finale, soit dans les cycles annexes ayant trait a la recuperation de plutonium a partir des scories d'elaboration du metal, des eaux-meres oxaliques et d'une facon generale des solutions aqueuses contenant du plutonium. Des traitements de regeneration du solvant ayant subi des degradations chimique ou radiolytique, sont proposes. (auteurs)

  16. 35 Typologie des eaux de surface du bassin du Sebou par multi ...

    African Journals Online (AJOL)

    PR BOKO

    2Service de protection de la qualité de l'eau, Agence du Bassin Hydraulique du ... pour montrer l'évolution de la qualité biologique des eaux de surface du ..... Biological Indicators of Freshwater Pollution and Environmental Management,.

  17. Régionalisation du recrutement du personnel de santé au Burkina ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Régionalisation du recrutement du personnel de santé au Burkina Faso ... le ministère a adopté une politique de recrutement régionalisé de certaines catégories du ... de comprendre le contexte dans lequel une telle stratégie a été formulée, ...

  18. Catalytic Combustion of Gasified Waste

    Energy Technology Data Exchange (ETDEWEB)

    Kusar, Henrik

    2003-09-01

    This thesis concerns catalytic combustion for gas turbine application using a low heating-value (LHV) gas, derived from gasified waste. The main research in catalytic combustion focuses on methane as fuel, but an increasing interest is directed towards catalytic combustion of LHV fuels. This thesis shows that it is possible to catalytically combust a LHV gas and to oxidize fuel-bound nitrogen (NH{sub 3}) directly into N{sub 2} without forming NO{sub x} The first part of the thesis gives a background to the system. It defines waste, shortly describes gasification and more thoroughly catalytic combustion. The second part of the present thesis, paper I, concerns the development and testing of potential catalysts for catalytic combustion of LHV gases. The objective of this work was to investigate the possibility to use a stable metal oxide instead of noble metals as ignition catalyst and at the same time reduce the formation of NO{sub x} In paper II pilot-scale tests were carried out to prove the potential of catalytic combustion using real gasified waste and to compare with the results obtained in laboratory scale using a synthetic gas simulating gasified waste. In paper III, selective catalytic oxidation for decreasing the NO{sub x} formation from fuel-bound nitrogen was examined using two different approaches: fuel-lean and fuel-rich conditions. Finally, the last part of the thesis deals with deactivation of catalysts. The various deactivation processes which may affect high-temperature catalytic combustion are reviewed in paper IV. In paper V the poisoning effect of low amounts of sulfur was studied; various metal oxides as well as supported palladium and platinum catalysts were used as catalysts for combustion of a synthetic gas. In conclusion, with the results obtained in this thesis it would be possible to compose a working catalytic system for gas turbine application using a LHV gas.

  19. Multi-Dimensional Modeling of the Aerodynamic and Combustion in Diesel Engines Modélisation multidimensionnelle de l'aérodynamique et de la combustion dans les moteurs diesel

    Directory of Open Access Journals (Sweden)

    Delhaye B.

    2006-12-01

    Full Text Available The purpose of this paper is to present an overview of Computational Fluid Dynamics (CFD and combustion simulation applications to automotive power train development, and the methodologies we developed at PSA to integrate numerical simulation into the development process. We illustrate these methodologies with some applications concerning the development of PSA HDI engines. Dans cet article, on présente un panorama des applications de la mécanique des fluides numérique et de la simulation de la combustion pour le développement des groupes motopropulseurs, ainsi que les méthodologies que nous avons conçues au sein du groupe PSA pour intégrer la simulation numérique dans ce processus de développement. Nous illustrons cette démarche par des exemples d'applications issues du développement des moteurs HDI injection directe common rail de PSA.

  20. La disparition du temps en gravitation quantique

    OpenAIRE

    Saint-Ours, Alexis de

    2012-01-01

    Le but de ce travail est d’examiner l’incidence philosophique de la gravitation quantique sur le concept de temps. Je cherche à montrer qu’elle conduit à une disparition du temps comme dimension et ouvre la voie à une compréhension du temps comme variation et même à l’idée de variation pure. En l’absence de temps mécanique, il est cependant possible de définir un temps d’origine thermodynamique. Je montre en quoi cette dissociation du temps mécanique et du temps thermodynamique, fait écho à l...

  1. Au fil du temps (1976 ou la loi du seuil

    Directory of Open Access Journals (Sweden)

    Isabelle Singer

    2010-04-01

    Full Text Available Ayant choisi de vivre dans un camion, les héros d’Au fil du temps (film de Wim Wenders de 1976 font du seuil une expérience particulière. Celle de la rupture avec toute idée de foyer et celle du refus d’appartenance à la terre natale, cette terre allemande traversée par une frontière le long de laquelle ils vont voyager, et qui les renvoie à chaque instant aux traumatismes de l’Histoire. Sur le pare-brise du camion, l’extérieur (campagnes indifférenciées, villes à l’abandon… et l’intérieur se superposent. Au fil du temps questionne le paysage : il s’agit d’en décoller un à un les mythes qui le recouvrent. L’image alors n’est plus surface mais volume à traverser, à lacérer et découvrir ce qui est tissé dans le paysage. La démarche de Wenders est alors proche de celle d’un de ses contemporains : Anselm Kiefer. Le paysage allemand provoque le rejet parce qu’il y a là toujours plus que le visible : des strates et des strates de culpabilité que le mythe - et c’est sa fonction - a recouvert. Et qu’il s’agira ici, de soulever. Le choix du nomadisme, c’est celui d’un état de l’humanité antérieur à l’idée de patrie. Et c’est aussi celui de la solitude, comme prix à payer à ce refus d’appartenance et à cette mise à jour des mythes. L’appartenance à la terre allemande et à son Histoire est profondément problématique parce que les pères sont fondamentalement coupables. On se reconnaîtra alors des pères de substitution : des pères de cinéma (Nicholas Ray ou Fritz Lang. Et l’on substituera l’Histoire du cinéma à l’Histoire. Bruno est réparateur ambulant de projecteurs et Au fil du temps dressera, au gré de ses pérégrinations, un état des lieux du cinéma allemand des années soixante-dix : déliquescent, colonisé par les images hollywoodiennes. Il faut que cela change : état du cinéma ; état des protagonistes solitaires en quête d’une identit

  2. Producer for vegetal combustibles for internal-combustion motors

    Energy Technology Data Exchange (ETDEWEB)

    1943-12-28

    A producer is described for internal-combustion motors fed with wood or agricultural byproducts characterized by the fact that its full operation is independent of the degree of wetness of the material used.

  3. Reducing emissions from diesel combustion

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper contains information dealing with engine design to reduce emissions and improve or maintain fuel economy. Topics include: Observation of High Pressure Fuel Spray with Laser Light Sheet Method; Determination of Engine Cylinder Pressures from Crankshaft Speed Fluctuations; Combustion Similarity for Different Size Diesel Engines: Theoretical Prediction and Experimental Results; Prediction of Diesel Engine Particulate Emission During Transient Cycles; Characteristics and Combustibility of Particulate Matter; Dual-Fuel Diesel Engine Using Butane; Measurement of Flame Temperature Distribution in D.I. Diesel Engine with High Pressure Fuel Injection: and Combustion in a Small DI Diesel Engine at Starting

  4. Magnesium and uranium ignition in different gaseous atmospheres; Inflammabilite du magnesium et de l'uranium dans l'air et le gaz carbonique

    Energy Technology Data Exchange (ETDEWEB)

    Darras, R; Baque, P; Leclercq, D [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Magnesium, uranium and some of their alloys burning temperatures have been systematically determined in an air or carbon dioxide atmosphere, either dry or wet. Two different ways of heating have been used: either continuously rising up the temperature, or heating to and then maintaining a constant temperature. The results are clearly different in the two cases. Besides, if moisture has little effect on the magnesium burning temperatures in air, it does lower them by about 130-140 deg. C in CO{sub 2}. The differences of sight between the burning of magnesium and uranium have been noticed; this leads to distinguish between an 'ignition' and an 'inflammation'. (author) [French] Les temperatures auxquelles apparait la combustion vive du magnesium, de l'uranium et certains de leurs alliages ont ete determinees systematiquement dans l'air et le gaz carbonique, soit secs, soit humidifies. On a mis en evidence l'influence du mode de chauffage sur les resultats: soit montee en temperature continue, soit stabilisation a partir d'une certaine temperature. En outre, si la presence d'humidite affecte peu les temperatures de combustion vive du magnesium dans l'air, elle les abaisse de 130 a 140 deg. C dans le gaz carbonique. Les differences d'aspect entre la combustion vive du magnesium et de l'uranium ont egalement ete remarquees, ce qui amene notamment a distinguer une 'ignition' d'une 'inflammation'. (auteur)

  5. Dew Point

    OpenAIRE

    Goldsmith, Shelly

    1999-01-01

    Dew Point was a solo exhibition originating at PriceWaterhouseCoopers Headquarters Gallery, London, UK and toured to the Centre de Documentacio i Museu Textil, Terrassa, Spain and Gallery Aoyama, Tokyo, Japan.

  6. Tipping Point

    Medline Plus

    Full Text Available ... Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture head injury product safety television tipover tv Watch the video in Adobe Flash ...

  7. Tipping Point

    Science.gov (United States)

    ... Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture head injury product safety television tipover tv Watch the video in Adobe Flash ...

  8. Tipping Point

    Medline Plus

    Full Text Available ... Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture head ... see news reports about horrible accidents involving young children and furniture, appliance and tv tip-overs. The ...

  9. Tipping Point

    Medline Plus

    Full Text Available ... Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture head ... TV falls with about the same force as child falling from the third story of a building. ...

  10. Tipping Point

    Medline Plus

    Full Text Available ... Tipping Point by CPSC Blogger September 22, 2009 appliance child Childproofing CPSC danger death electrical fall furniture ... about horrible accidents involving young children and furniture, appliance and tv tip-overs. The force of a ...

  11. Computational Modeling of Turbulent Spray Combustion

    NARCIS (Netherlands)

    Ma, L.

    2016-01-01

    The objective of the research presented in this thesis is development and validation of predictive models or modeling approaches of liquid fuel combustion (spray combustion) in hot-diluted environments, known as flameless combustion or MILD combustion. The goal is to combine good physical insight,

  12. Measures for a quality combustion (combustion chamber exit and downstream); Mesures pour une combustion de qualite (sortie de chambre de combustion et en aval)

    Energy Technology Data Exchange (ETDEWEB)

    Epinat, G. [APAVE Lyonnaise, 69 (France)

    1996-12-31

    After a review of the different pollutants related to the various types of stationary and mobile combustion processes (stoichiometric, reducing and oxidizing combustion), measures and analyses than may be used to ensure the quality and efficiency of combustion processes are reviewed: opacimeters, UV analyzers, etc. The regulation and control equipment for combustion systems are then listed, according to the generator capacity level

  13. Fuels and Combustion | Transportation Research | NREL

    Science.gov (United States)

    Fuels and Combustion Fuels and Combustion This is the March 2015 issue of the Transportation and , combustion strategy, and engine design hold the potential to maximize vehicle energy efficiency and performance of low-carbon fuels in internal combustion engines with a whole-systems approach to fuel chemistry

  14. Mise au point

    African Journals Online (AJOL)

    31 mai 2013 ... traités au service de chirurgie maxillo-faciale et chirurgie plastique de l'hôpital ... qui est la fracture simple isolée du corps, on a inclut ce type de fracture ... sion latérale au niveau de la queue du sourcil. La voie vestibulaire ...

  15. Combustion modeling in waste tanks

    International Nuclear Information System (INIS)

    Mueller, C.; Unal, C.; Travis, J.R.; Forschungszentrum Karlsruhe

    1997-01-01

    This paper has two objectives. The first one is to repeat previous simulations of release and combustion of flammable gases in tank SY-101 at the Hanford reservation with the recently developed code GASFLOW-II. The GASFLOW-II results are compared with the results obtained with the HMS/TRAC code and show good agreement, especially for non-combustion cases. For combustion GASFLOW-II predicts a steeper pressure rise than HMS/TRAC. The second objective is to describe a so-called induction parameter model which was developed and implemented into GASFLOW-II and reassess previous calculations of Bureau of Mines experiments for hydrogen-air combustion. The pressure time history improves compared with the one-step model, and the time rate of pressure change is much closer to the experimental data

  16. Environmental sensing and combustion diagnostics

    International Nuclear Information System (INIS)

    Santoleri, J.J.

    1991-01-01

    This book contains proceedings of Environmental Sensing and Combustion Diagnostics. Topics covered include: Incineration Systems Applications, Permitting, And Monitoring Overview; Infrared Techniques Applied to Incineration Systems; Continuous Emission Monitors; Analyzers and Sensors for Process Control And Environmental Monitoring

  17. Sodium nitrate combustion limit tests

    International Nuclear Information System (INIS)

    Beitel, G.A.

    1976-04-01

    Sodium nitrate is a powerful solid oxidant. Energetically, it is capable of exothermically oxidizing almost any organic material. Rate-controlling variables such as temperature, concentration of oxidant, concentration of fuel, thermal conductivity, moisture content, size, and pressure severely limit the possibility of a self-supported exothermic reaction (combustion). The tests reported in this document were conducted on one-gram samples at atmospheric pressure. Below 380 0 C, NaNO 3 was stable and did not support combustion. At moisture concentrations above 22 wt percent, exothermic reactions did not propagate in even the most energetic and reactive compositions. Fresh resin and paraffin were too volatile to enable a NaNO 2 -supported combustion process to propagate. Concentrations of NaNO 3 above 95 wt percent or below 35 wt percent did not react with enough energy release to support combustion. The influence of sample size and confining pressure, both important factors, was not investigated in this study

  18. 75 FR 3881 - Combustible Dust

    Science.gov (United States)

    2010-01-25

    ..., rubber, drugs, dried blood, dyes, certain textiles, and metals (such as aluminum and magnesium..., furniture manufacturing, metal processing, fabricated metal products and machinery manufacturing, pesticide... standard that will comprehensively address the fire and explosion hazards of combustible dust. The Agency...

  19. Modeling of microgravity combustion experiments

    Science.gov (United States)

    Buckmaster, John

    1995-01-01

    This program started in February 1991, and is designed to improve our understanding of basic combustion phenomena by the modeling of various configurations undergoing experimental study by others. Results through 1992 were reported in the second workshop. Work since that time has examined the following topics: Flame-balls; Intrinsic and acoustic instabilities in multiphase mixtures; Radiation effects in premixed combustion; Smouldering, both forward and reverse, as well as two dimensional smoulder.

  20. Quantifying emissions from spontaneous combustion

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-09-01

    Spontaneous combustion can be a significant problem in the coal industry, not only due to the obvious safety hazard and the potential loss of valuable assets, but also with respect to the release of gaseous pollutants, especially CO2, from uncontrolled coal fires. This report reviews methodologies for measuring emissions from spontaneous combustion and discusses methods for quantifying, estimating and accounting for the purpose of preparing emission inventories.

  1. Combustion Modeling with the G-Equation Modélisation de la combustion avec l'équation de G

    Directory of Open Access Journals (Sweden)

    Peters N.

    2006-12-01

    Full Text Available Numerical investigations concerning the turbulent flame front propagation in Gasoline Direct Injection (GDI engines were made by implementing a flamelet model in the CFD code Fire. The advantage of this combustion model is the decoupling of the chemistry from the turbulent flow. For this purpose the combustion chamber has to be divided into a burned and an unburned area, which is realized by transporting a scalar field (G-Equation. The reference value defines the present averaged flame position. The complete reaction kinetics is calculated interactively with the CFD code in a one dimensional Representative Interactive Flamelet (RIF code. This combustion model was verified by simulating a 2. 0 l-2 V gasoline engine with homogeneous combustion where a parameter study was conducted to check the flamelet model for plausibility. Finally, the potential of this combustion model was investigated by simulating a hypothetical 2. 0 1-4 V GDI engine. Une investigation numérique relative à la propagation des fronts de flammes turbulents dans les moteurs à essence à injection directe (GDI a été menée en implantant un modèle de flameletdans le code 3D Fire. L'avantage de ce modèle de combustion est de découpler la chimie de l'écoulement turbulent en divisant la chambre de combustion en deux zones : brûlée et imbrûlée, à l'aide d'une équation de transport d'un scalaire (équation de G. Une valeur de référence de ce scalaire définit la position moyenne de la flamme. Une chimie complète est calculée interactivement avec le calcul 3D à l'aide d'un code monodimensionnel RIF (Representative Interactive Flamelet. Le modèle de combustion a été validé sur la simulation d'un moteur 2 litres à 2 soupapes en combustion homogène pour vérifier la représentativité de l'approche flamelet . Puis, le potentiel du modèle de combustion a été étudié en simulant un moteur modèle 2 litres 4 soupapes GDI.

  2. Fabrication of the 4. set of fuel elements for the experimental pile EL2; Fabrication du 4. jeu de barreaux de la pile d'essai EL2

    Energy Technology Data Exchange (ETDEWEB)

    Ringot, C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    The reactor EL2 is the second atomic reactor built in France. It is a laboratory reactor using heavy water and natural uranium. Its cooling circuit operates with compressed CO{sub 2} gas at 8 kg/cm{sup 2} pressure. The subject of this lecture is the manufacturing of the fourth set of rods. The principle of uranium-can connection is exposed: that is the principle of a pre-pressed bound can. The EL2 reactor has been a prototype with respect to this aspect of the question, and a prototype which has been quite satisfactory. The main steps of the fabrication are exposed: the {gamma} phase extension of uranium, the machining, the three canning (die canning, hydraulic canning, compressed air treatment), the automatic argon arc welding of cups and the different manufacturing controls. (author) [French] Le reacteur EL2 est le deuxieme reacteur construit en France. C'est un reacteur de recherches qui utilise de l'eau lourde et de l'uranium naturel. Il est refroidi par du gaz carbonique sous 8 kg/cm{sup 2} de pression. On etudie dans cet expose la fabrication du quatrieme jeu d'elements combustibles. Le principe de la liaison uranium-gaine est expose: c'est celui d'une gaine precontrainte. La pile EL2 a constitue un prototype a ce point de vue, prototype qui a donne entiere satisfaction. Les principales etapes de la fabrication sont ensuite expliquees: le filage {gamma} de l'uranium, l'usinage des barreaux, les trois operations de gainages (gainage par filiere, gainage hydraulique, gainage a chaud), la soudure automatique des bouchons a l'argon-arc et les differents controles de fabrication. (auteur)

  3. Combustion means for solid fuels

    Energy Technology Data Exchange (ETDEWEB)

    Murase, D.

    1987-09-23

    A combustion device for solid fuel, suitable for coal, coke, charcoal, coal-dust briquettes etc., comprising:- a base stand with an opening therein, an imperforate heat resistant holding board locatable to close said opening; a combustion chamber standing on the base stand with the holding board forming the base of the combustion chamber; a wiper arm pivoted for horizontal wiping movement over the upper surface of the holding board; an inlet means at a lower edge of said chamber above the base stand, and/or in a surrounding wall of said chamber, whereby combustion air may enter as exhaust gases leave the combustion chamber; an exhaust pipe for the exhaust gases; generally tubular gas-flow heat-exchange ducting putting the combustion chamber and exhaust pipe into communication; and means capable of moving the holding board into and out of the opening for removal of ash or other residue. The invention can be used for a heating system in a house or in a greenhouse or for a boiler.

  4. Sur la plurifonctionnalité du discours direct

    Directory of Open Access Journals (Sweden)

    Cigada Sara

    2012-07-01

    Full Text Available La comparaison entre les résultats de nombreux travaux sur le dialogue dans le texte littéraire, sur l’attestation linguistique de la subjectivité, sur la fonction argumentative des émotions dans le discours et sur les effets de polyphonie, suggère que la structure sémiotique et linguistique du discours direct (DD se trouve au croisement stratégique de plusieurs axes de la construction discursive. Nous étudions donc l’insertion du DD dans le discours (cf. Rosier 2008: Le discours rapporté en français; Kerbrat 2005: Le Discours en interaction et Id. 2008: Le Dialogue comme objet d’analyse linguistique; Maingueneau 2010: Manuel de linguistique pour le texte littéraire en tant que phénomène de rupture sémiotique (Genette 1972: Figures III et Id. 1983: Nouveau discours du récit, dans ses fonctions discursives plurielles, tantôt émotives (Tannen 1989: Talking Voices; Plantin-Traverso-Vosghanian 2008: Parcours des émotions en interaction, tantôt argumentatives (Doury 2001: La Fonction argumentative des échanges rapportés; Stati 1990: Le transphrastique. Du point de vue méthodologique, nous nous proposons de revisiter empiriquement, par l'étude de corpus, les traits linguistiques structuraux qui caractérisent l’insertion du DD dans un récit à l'écrit, en les comparant systématiquement aux traits de l’insertion du DD dans un récit à l'oral. Une analyse parallèle est possible en ce qui concerne les fonctions discursives, que le DD typiquement déroule dans les récits. Les fonctions du DD décrites à partir de l'étude des corpus sont plurielles: on reconnaît des fonctions fortement argumentatives d'autres plus typiquement narratives, tandis que d'autres encore amalgament les deux fonctions. Le « contrat de littéralité », qui selon Genette ne porterait jamais que sur la teneur du discours, doit donc être fortement nuancé selon les contextes, tandis que l'effet de sens le plus directement lié à la

  5. Le vide univers du tout et du rien

    CERN Document Server

    Diner, Simon

    1997-01-01

    Pourquoi l'Univers plutôt que le vide ? Le temps et l'espace existent-ils en l'absence de l'Univers ? Que reste-t-il quand tout est enlevé ? Pourquoi quelque chose plutôt que rien ? Depuis des siècles, ces interrogations mobilisent philosophes et physiciens. Mais aujourd'hui, le vide n'est pas le rien. Il serait même l'acteur central de l'histoire de la matière et de l'Univers, le partenaire privilégié de la physique. Vide et matière ne sont plus deux manifestations séparées de la nature, mais deux aspects d'une même réalité. Le vide est l'état de base dont la matière émerge, sans couper son cordon ombilical Le vide comme Univers du rien cède la place au vide comme Univers du tout. Que le vide puisse être conçu par les physiciens comme réservoir potentiel d'univers, voici qui ne devrait laisser personne indifférent. Ce livre ouvre un débat et nous convie à une réflexion surprenante.

  6. Image du savoir, image du pouvoir dans le Lapidaire

    Directory of Open Access Journals (Sweden)

    Marta LACOMBA

    2007-01-01

    Full Text Available À travers le prologue et les enluminures de présentation, le Lapidaire d’Alphonse X oriente l’interprétation de l’œuvre. Ces paratextes mettent en avant le rôle capital du savoir, représenté par la métaphore du trésor caché, qui a ici une valeur topique. Ils mettent également en exergue le rôle que s’attribue le roi dans la transmission de ce savoir, et placent cette nouvelle attribution royale au cœur de son projet politique.A través del prólogo y las miniaturas de presentación, el Lapidario de Alfonso X orienta la interpretación de la obra. Estos paratextos subrayan el papel capital del saber, representado por la metáfora del tesoro escondido, que tiene aquí un valor tópico. Ponen asimismo de manifiesto el papel que se atribuye el monarca en la transmisión de ese saber y colocan esta nueva atribución real en el centro de su proyecto político.

  7. Main: 1DU5 [RPSD[Archive

    Lifescience Database Archive (English)

    Full Text Available 1DU5 トウモロコシ Corn Zea mays L. Zeamatin Precursor. Name=Zlp; Zea Mays Molecule: Zeamatin; Chai...eta Sandwich SWS:ZEAM_MAIZE,P33679|EMBL; U06831; AAA92882.1; -.|PIR; T02075; T02075.|PDB; 1DU5; X-ray; A/B=22-227.|Mai

  8. les cahiers du cread: About this journal

    African Journals Online (AJOL)

    les cahiers du cread: About this journal. Journal Home > les cahiers du cread: About this journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. People. » Contact. Policies.

  9. Contribution de la consolidation au maintien du patrimoine

    CERN Document Server

    Chevret, P

    2001-01-01

    Les premiers bâtiments du Laboratoire datent de 1954 et les équipements techniques les plus anciens encore en service dans ces bâtiments datent de 1956. Nombre d'entre eux sont toujours constitués des matériels d'origine qui ont largement dépassé leur espérance de vie normale et ne satisfont plus aux normes de sécurité. La non disponibilité fréquente de pièces de rechange sur des matériels obsolètes, les risques encourus tant par les exploitants que par les utilisateurs du point de vue de la sécurité, et les co ts de maintenance qui ne peuvent être contenus en l'absence de budget d'investissement, ont conduit le groupe ST-TFM, au cours des dernières années, à lancer un minimum de projets de consolidation pour empêcher la dégradation du patrimoine. Ce document synthétise les différentes actions entreprises et montre que l'effort doit être maintenu, voire accru, si l'on veut globaliser vers l'extérieur les opérations de maintenance dans de bonnes conditions.

  10. Synthesis of phenobarbital {sup 14}C - 5 (1964); Synthese du phenobarbital {sup 14}C - 5 (1964)

    Energy Technology Data Exchange (ETDEWEB)

    Benakis, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Phenobarbital (Luminal), well known as a hypnotic agent, plays also an important role in the medical treatment of epilepsy. With the object of studying the metabolism of this medicament in the living system, the synthesis of phenobarbital marked in position 2 of the pyrimidinic ring has been effected. It has been necessary, in order to carry out to research into the metabolism of this product, to have a phenobarbital marked in position 5 of the pyrimidinic ring. This synthesis, making it possible to introduce C-14 into position 5 of the pyrimidinic ring, consists of seven stages starting from C-14 carboxyl benzoic acid having a specific activity of 25 mc/mM. The melting point of the final product is 172 - 173 deg. C and its specific activity is 11.15 mc/mM. The overall radioactive yield of the pure product, with respect to the original benzoic acid (10 mM) is of the order of 3 per cent. The purity of the product has been controlled by paper chromatography; it is of the order of 99 per cent. (author) [French] Le phenobarbital (Luminal) bien connu comme agent hypnotique, joue egalement un role important dans la medication anti-epileptique. Pour l'etude du metabolisme de ce medicament dans l'organisme vivant, nous avons synthetise le phenobarbital marque en position 2 du cycle pyrimidinique. Afin de poursuivre la recherche du metabolisme de ce produit, il a ete necessaire de disposer du phenobarbital marque en position 5 du cycle. pyrimidinique. Cette synthese, permettant l'introduction du {sup 14}C en position 5 du cycle pyrimidinique, comporte sept etapes, au depart de l'acide benzoique carboxyle {sup 14}C, d'une activite specifique de 25 mc/mM. Point de fusion du produit final: 172 - 173 deg. C Activite specifique: 11,15 mC/mM. Rendement total radioactif du produit pur, par rapport a l'acide benzoique de depart sur 10 mM, de l'ordre de 3 pour cent. La purete du produit a ete controlee par chromatographie sur papier; elle est de l'ordre de 99 pour cent. (auteur)

  11. Les figures multiples du maire.

    Directory of Open Access Journals (Sweden)

    Olivier Lebraud

    2004-06-01

    Full Text Available Alors même que l’ensemble du personnel gouvernemental et parlementaire est sujet à une relative désaffection de la part des citoyens, les maires français jouissent, on le sait, d’une popularité qui fait d’eux les figures centrales de la scène politique. Au-delà de la décentralisation, qui a souvent renforcé leur image de décideurs, ils ont su tirer parti de la dimension identitaire qui caractérise l’échelon communal pour devenir les acteurs indispensables de la vie locale. ...

  12. Vers une anthropologie du Confucianisme

    OpenAIRE

    Rieu , Alain-Marc

    2010-01-01

    Research in Anthropology developed in France by Jean-Pierre Vernant, Marcel Détienne and Philippe Descola opens the possibility to reframe the debate and research on the function of Confucianism in Chinese culture, history and society. This paper shows how Confucianism can be studied as a "mythology"; La fonction du Confucianisme dans l'histoire de la société et de la culture chinoise, les débats et les reconstructions dont il est l'objet et l'enjeu, ouvre la possibilité de l'étudier d'un poi...

  13. Session du Conseil du CERN : le ministre britannique, Robert Jackson, souligne l'intérêt de on pays pour l'avenir du CERN : décisions du Conseil pour la mise en oeuvre des recommandations du Comité d'évaluation du CERN: départ anticipé pour 200 membres au moins du personnel - mise à jour de la méthode de calcule pour les contributions des Etats Membres au budget

    CERN Multimedia

    CERN Press Office. Geneva

    1988-01-01

    Session du Conseil du CERN : le ministre britannique, Robert Jackson, souligne l'intérêt de on pays pour l'avenir du CERN : décisions du Conseil pour la mise en oeuvre des recommandations du Comité d'évaluation du CERN: départ anticipé pour 200 membres au moins du personnel - mise à jour de la méthode de calcule pour les contributions des Etats Membres au budget

  14. Detection of spontaneous combustion underground by measuring CO levels

    Energy Technology Data Exchange (ETDEWEB)

    Boutonnat, M; Jeger, M

    1980-01-01

    It is essential to detect spontaneous combustion as soon as it occurs so as to prevent such outbreaks from becoming a serious conflagration. At present CO detection is the basic method used. States the need for setting up additional measuring points (in air returns from working palces and in return airways in general). Where possible measuring instruments should be placed near zones where there is a particularly high risk of spontaneous combustion. Measurement should be undertaken on a continuous basis or as frequently as possible and must be capable of distinguishing between extraneous CO (shotfiring and diesel motors) and CO emanating from outbreaks of spontaneous combustion. The article describes two instruments developed by CERCHAR: the remote-control CO monitors type C and CSD. Both devices make use of a UNOR analyser.

  15. Modélisation de la combustion de fuels lourds prenant en compte la dispersion des asphaltènes Modeling Heavy Fuel-Oil Combustion (While Considering Or Including Asphaltene Dispersion

    Directory of Open Access Journals (Sweden)

    Audibert F.

    2006-11-01

    Full Text Available Divers modèles, ayant pour but de prédire le taux d'imbrûlés solides lors de la combustion du fuel lourd, ont été mis au point dans le passé. Les paramètres entrant en ligne de compte sont le plus souvent les teneurs en résidus lourds hydrocarbonés (asphaltènes précipités au pentane ou à l'heptane et carbone Conradson et en métaux : c'est le cas des modèles Exxon et Shell développés respectivement en 1979 et 1981. D'autres modèles tiennent compte, en plus de la composition du fuel, de son mode d'atomisation, de son mode de diffusion dans le foyer et de la cinétique de combustion : on peut citer les travaux du Laboratoire Energie du MIT publiés en 1986. Néanmoins, ces facteurs ne sont pas les seuls à intervenir : l'expérience a montré que l'état de dispersion des asphaltènes peut jouer également un grand rôle, notamment dans le cas d'installations de combustion à injection mécanique, pour lesquelles la dispersion des gouttelettes n'est pas aussi fine que pour des installations munies d'une injection assistée par la vapeur. Cette influence de la dispersion des asphaltènes sur la combustion a été mise en évidence dans le passé par l'utilisation d'additifs dispersants et également par la combustion de fuels lourds constitués par dilution d'asphaltes précipités au pentane avec un gas-oil de cracking catalytique de raffinerie (LCO. Ce sont ces fuels que l'on a considérés dans la présente étude. L'effet de ce facteur dispersion n'a pas été quantifié jusqu'alors, la difficulté étant de définir une grandeur mesurable représentant la répartition des agglomérats d'asphaltènes. Dans cette étude, on a essayé en un premier temps de faire une approche fractale de la répartition des asphaltènes à partir de clichés (préparés par la société Total, cette méthode ayant déjà été utilisée avec succès pour décrire des structures d'aspects comparables. Malheureusement, on s'est heurté à des

  16. Comprehensive investigation of process characteristics for oxy-steam combustion power plants

    International Nuclear Information System (INIS)

    Jin, Bo; Zhao, Haibo; Zou, Chun; Zheng, Chuguang

    2015-01-01

    Highlights: • Oxy-steam combustion exhibits better performance than oxy-CO 2 combustion. • Cost of electricity in oxy-steam combustion is 6.62% less than oxy-CO 2 combustion. • The increase of oxygen concentration in oxidant can improve its system performance. • The decrease of excess oxygen coefficient can be helpful for its system performance. • Integration with solar technology can enhance its thermodynamic performance. - Abstract: Oxy-steam combustion, as an alternative option of oxy-fuel combustion technology, is considered as a promising CO 2 capture technology for restraining CO 2 emissions from power plants. To attain its comprehensive process characteristics, process simulation, thermodynamic assessment, and sensitivity analysis for oxy-steam combustion pulverized-coal-fired power plants are investigated whilst its corresponding CO 2 /O 2 recycled combustion (oxy-CO 2 combustion) power plant is served as the base case for comparison. Techno-economic evaluation and integration with solar parabolic trough collectors are also discussed to justify its economic feasibility and improve its thermodynamic performance further, respectively. It is found that oxy-steam combustion exhibits better performance than oxy-CO 2 combustion on both thermodynamic and economic aspects, in which the cost of electricity decreases about 6.62% whilst the net efficiency and exergy efficiency increase about 0.90 and 1.01 percentage points, respectively. The increment of oxygen concentration in oxidant (20–45 mol.%) and decrease of excess oxygen coefficient (1.01–1.09) in a certain range are favorable for improving oxy-steam combustion system performance. Moreover, its thermodynamic performance can be improved when considering solar parabolic trough collectors for heating recycled water, even though its cost of electricity increases about 2 $/(MW h)

  17. Thermodynamic energy and exergy analysis of three different engine combustion regimes

    International Nuclear Information System (INIS)

    Li, Yaopeng; Jia, Ming; Chang, Yachao; Kokjohn, Sage L.; Reitz, Rolf D.

    2016-01-01

    Highlights: • Energy and exergy distributions of three different combustion regimes are studied. • CDC demonstrates the highest utilization efficiency of heat transfer and exhaust. • HCCI achieves the highest energy and exergy efficiencies over CDC and RCCI. • HCCI and RCCI demonstrate lower exergy destruction than CDC. • Combustion temperature, rate, duration and regime affect exergy destruction. - Abstract: Multi-dimensional models were coupled with a detailed chemical mechanism to investigate the energy and exergy distributions of three different combustion regimes in internal combustion engines. The results indicate that the 50% heat release point (CA50) considerably affects fuel efficiency and ringing intensity (RI), in which RI is used to quantify the knock level. Moreover, the burn duration from the 10% heat release point (CA10) to CA50 dominates RI, and the position of 90% heat release point (CA90) affects fuel efficiency. The heat transfer losses of conventional diesel combustion (CDC) strongly depend on the local temperature gradient, while it is closely related to the heat transfer area for homogeneous charge compression ignition (HCCI) and reactivity controlled compression ignition (RCCI). Among the three combustion regimes, CDC has the largest utilization efficiency for heat transfer and exhaust energy due to its higher temperature in the heat transfer layer and higher exhaust pressure and temperature. The utilization efficiency of heat transfer and exhaust in RCCI is less affected by the variation of CA50 compared to those in CDC and HCCI. Exergy destruction is closely related to the homogeneity of in-cylinder temperature and equivalence ratio during combustion process, the combustion temperature, the chemical reaction rate, and the combustion duration. Under the combined effect, HCCI and RCCI demonstrate lower exergy destruction than CDC at the same load. Overall, the variations of the exergy distribution for the three combustion regimes

  18. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    The Combustion Byproducts Recycling Consortium (CBRC) program was developed as a focused program to remove and/or minimize the barriers for effective management of over 123 million tons of coal combustion byproducts (CCBs) annually generated in the USA. At the time of launching the CBRC in 1998, about 25% of CCBs were beneficially utilized while the remaining was disposed in on-site or off-site landfills. During the ten (10) year tenure of CBRC (1998-2008), after a critical review, 52 projects were funded nationwide. By region, the East, Midwest, and West had 21, 18, and 13 projects funded, respectively. Almost all projects were cooperative projects involving industry, government, and academia. The CBRC projects, to a large extent, successfully addressed the problems of large-scale utilization of CCBs. A few projects, such as the two Eastern Region projects that addressed the use of fly ash in foundry applications, might be thought of as a somewhat smaller application in comparison to construction and agricultural uses, but as a novel niche use, they set the stage to draw interest that fly ash substitution for Portland cement might not attract. With consideration of the large increase in flue gas desulfurization (FGD) gypsum in response to EPA regulations, agricultural uses of FGD gypsum hold promise for large-scale uses of a product currently directed to the (currently stagnant) home construction market. Outstanding achievements of the program are: (1) The CBRC successfully enhanced professional expertise in the area of CCBs throughout the nation. The enhanced capacity continues to provide technology and information transfer expertise to industry and regulatory agencies. (2) Several technologies were developed that can be used immediately. These include: (a) Use of CCBs for road base and sub-base applications; (b) full-depth, in situ stabilization of gravel roads or highway/pavement construction recycled materials; and (c) fired bricks containing up to 30%-40% F

  19. Improved correlations of hydrogen content versus combustion performance related properties of aviation turbine fuels

    Energy Technology Data Exchange (ETDEWEB)

    Nagpal, J.M.; Sharma, R.L.; Sagu, M.L.; Tiwari, G.B. (Indian Institute of Petroleum, Dehradun (India))

    1994-01-01

    In recent years the hydrogen content of Aviation Fuels has generated considerable interest. Various investigators have suggested correlation of hydrogen content with combustion related properties of aviation turbine fuel (ATF). A suitable threshold value of hydrogen content 13.8 wt% is being considered as a waiver of specifications such as specific energy, aniline gravity product, smoke point, aromatic content, naphthalenes and luminometer number. In the present paper relationship between the hydrogen content and combustion related properties has been examined and improved correlations of hydrogen content with several combustion related properties have been developed by incorporating a characterization factor in the equations. The supporting threshold value of a hydrogen content of 13.8wt% is verified with 25 data points for waiving of combustion properties such as specific energy, aniline gravity product, smoke point and aromatic content from aviation turbine fuel. 6 refs., 12 figs., 2 tabs.

  20. HERCULES Advanced Combustion Concepts Test Facility: Spray/Combustion Chamber

    Energy Technology Data Exchange (ETDEWEB)

    Herrmann, K. [Eidgenoessische Technische Hochschule (ETH), Labor fuer Aerothermochemie und Verbrennungssysteme, Zuerich (Switzerland)

    2004-07-01

    This yearly report for 2004 on behalf of the Swiss Federal Office of Energy (SFOE) at the Laboratory for Aero-thermochemistry and Combustion Systems at the Federal Institute of Technology ETH in Zurich, Switzerland, presents a review of work being done within the framework of HERCULES (High Efficiency R and D on Combustion with Ultra Low Emissions for Ships) - the international R and D project concerning new technologies for ships' diesels. The work involves the use and augmentation of simulation models. These are to be validated using experimental data. The report deals with the development of an experimental set-up that will simulate combustion in large two-stroke diesel engines and allow the generation of reference data. The main element of the test apparatus is a spray / combustion chamber with extensive possibilities for optical observation under variable flow conditions. The results of first simulations confirm concepts and shall help in further work on the project. The potential offered by high-speed camera systems was tested using the institute's existing HTDZ combustion chamber. Further work to be done is reviewed.

  1. Jet plume injection and combustion system for internal combustion engines

    Science.gov (United States)

    Oppenheim, Antoni K.; Maxson, James A.; Hensinger, David M.

    1993-01-01

    An improved combustion system for an internal combustion engine is disclosed wherein a rich air/fuel mixture is furnished at high pressure to one or more jet plume generator cavities adjacent to a cylinder and then injected through one or more orifices from the cavities into the head space of the cylinder to form one or more turbulent jet plumes in the head space of the cylinder prior to ignition of the rich air/fuel mixture in the cavity of the jet plume generator. The portion of the rich air/fuel mixture remaining in the cavity of the generator is then ignited to provide a secondary jet, comprising incomplete combustion products which are injected into the cylinder to initiate combustion in the already formed turbulent jet plume. Formation of the turbulent jet plume in the head space of the cylinder prior to ignition has been found to yield a higher maximum combustion pressure in the cylinder, as well as shortening the time period to attain such a maximum pressure.

  2. Bases en technique du vide

    CERN Document Server

    Rommel, Guy

    2017-01-01

    Cette seconde édition, 20 ans après la première, devrait continuer à aider les techniciens pour la réalisation de leur système de vide. La technologie du vide est utilisée, à présent, dans de nombreux domaines très différents les uns des autres et avec des matériels très fiables. Or, elle est souvent bien peu étudiée, de plus, c'est une discipline où le savoir-faire prend tout son sens. Malheureusement la transmission par des ingénieurs et techniciens expérimentés ne se fait plus ou trop rapidement. La technologie du vide fait appel à la physique, à la chimie, à la mécanique, à la métallurgie, au dessin industriel, à l'électronique, à la thermique, etc. Cette discipline demande donc de maîtriser des techniques de domaines très divers, et ce n'est pas chose facile. Chaque installation est en soi un cas particulier avec ses besoins, sa façon de traiter les matériaux et celle d'utiliser les matériels. Les systèmes de vide sont parfois copiés d'un laboratoire à un autre et le...

  3. Analysis of two different types of hydrogen combustion during severe accidents in a typical pressurized water reactor

    International Nuclear Information System (INIS)

    Ko Yuchih; Lee Min

    2005-01-01

    Hydrogen combustion is an important phenomenon that may occur during severe accidents of Nuclear Power Plants (NPPs). Depending on the specific plant design, the initiating events, and mitigation actions executed, hydrogen combustion may have distinct characteristics and may damage the plant in various degrees. The worst scenario will be the catastrophic failure of containment. In this study two specific types of hydrogen combustion are analyzed to evaluate their impact on the containment integrity. In this paper, Station Blackout (SBO) and Loss of Coolant Accidents (LOCAs) sequences are analyzed using MAAP4 (Modular Accident Analysis Program) code. The former sequence is used to represent hydrogen combustion phenomenon under the condition that the reactor pressure vessel (RPV) breaches at high pressure and the latter sequence represents the phenomenon that RPV fails at low pressure. Two types of hydrogen combustion are observed in the simulation. The Type I hydrogen combustion represents global and instantaneous hydrogen combustion. Large pressure spike is created during the combustion and represents a threat to containment integrity. Type II hydrogen combustion is localized burn and burn continuously over a time period. There is hardly any impact of this type hydrogen burn on the containment pressurization rate. Both types of hydrogen combustion can occur in the severe accidents without any human intervention. From the accident mitigation point of view, operators should try to bring the containment into conditions that favor the Type II hydrogen combustion. (authors)

  4. L'obtention du crédit bancaire par les PME au Cameroun

    African Journals Online (AJOL)

    Doctorante en sciences de gestion Université de Ngaoundéré, Cameroun. .... vient à point nommé dans son contexte et dans son domaine dans la mesure ... confrontant la performance des entreprises à leur structure financière, Wanda ..... est le plus souvent la perte du contrôle de l'entreprise par les actionnaires.

  5. Twenty-fifth symposium (international) on combustion

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    Approximately two-thirds of the papers presented at this conference are contained in this volume. The other one-third appear in special issues of ''Combustion and Flame'', Vol. 99, 1994 and Vol. 100, 1995. Papers are divided into the following sections: Supersonic combustion; Detonations and explosions; Internal combustion engines; Practical aspects of combustion; Incineration and wastes; Sprays and droplet combustion; Coal and organic solids combustion; Soot and polycyclic aromatic hydrocarbons; Reaction kinetics; NO x ; Turbulent flames; Turbulent combustion; Laminar flames; Flame spread, fire and halogenated fire suppressants; Global environmental effects; Ignition; Two-phase combustion; Solid propellant combustion; Materials synthesis; Microgravity; and Experimental diagnostics. Papers have been processed separately for inclusion on the data base

  6. Chemical Looping Combustion with Different Types of Liquid Fuels Combustion en boucle chimique avec différentes charges liquides

    Directory of Open Access Journals (Sweden)

    Hoteit A.

    2011-02-01

    Full Text Available CLC is a new promising combustion process for CO2 capture with less or even no energy penalty compared to other processes. Up to now, most of the work performed on CLC was conducted with gaseous or solid fuels, using methane and coal and/or pet coke. Liquid fuels such as heavy fuels resulting from oil distillation or conversion may also be interesting feedstocks to consider. However, liquid fuels are challenging feedstock to deal with in fluidized beds. The objective of the present work is therefore to investigate the feasibility of liquid feed injection and contact with oxygen carrier in CLC conditions in order to conduct partial or complete combustion of hydrocarbons. A batch experimental fluidized bed set-up was developed to contact alternatively oxygen carrier with liquid fuels or air. The 20 mm i.d. fluidized bed reactor was filled up with 45 g of NiAl0.44O1.67 and pulses of 1-2 g of liquid were injected in the bed at high temperatures up to 950˚C. Different feedstocks have been injected, from dodecane to heavy fuel oils No.2. Results show that, during the reduction period, it is possible to convert all the fuel injected and there is no coke remaining on particles at the end of the reduction step. Depending upon oxygen available in the bed, either full combustion or partial combustion can be achieved. Similar results were found with different liquid feeds, despite their different composition and properties. Le CLC est un nouveau concept prometteur appliqué à la combustion qui permet le captage de CO en minimisant la pénalité énergétique liée au captage. Jusqu’à présent, l’essentiel des travaux de recherche dans le domaine du CLC concerne les charges gazeuses (méthane et solides (charbon et coke. Les charges liquides, et particulièrement les résidus pétroliers, sont des charges également intéressantes à considérer a priori. La mise en oeuvre de ces charges en lit fluidisé est cependant délicate. L’objet de ce

  7. Tanguy du Chastel, l'homme de Montereau.

    OpenAIRE

    Cassard, Jean-Christophe

    2004-01-01

    ISBN : 2-9513922-1-4 ; 332 p.; National audience; Né dans une famille de moyenne noblesse possessionnée à la pointe de Bretagne, Tanguy du Chastel servira fidèlement le dauphin Charles, devenu Charles VI. Soupçonné d'avoir porté des coups mortels au duc de Bourgogne lors d'une rencontre organisée sur le pont de Montereau, l'ancien prévôt de Paris connaît une seconde carrière en Provence, sans jamais rompre avec son pays d'origine.

  8. Combustion of sodium in the open atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Morewith, H A; Johnson, R P; Nelson, C T; Otter, J M [Energy System Group, Rockwell International, Rockwell (United States)

    1979-03-01

    A series of sodium fire tests has been conducted in ambient air at a meteorological test site. This test series was designed to simulate hypothetical accidents which might occur in the heat transport system of an LMFBR. Measurements of concentration, agglomeration, fallout, and chemical species of the sodium combustion products were made as a function of downwind distance. In each of the first two tests, {approx}23 kg of 540 deg. C sodium was sprayed as a fan of 250-{mu}m sodium drops across the wind, from heights of 5 or 6 m. Each release took a few minutes. A dense sodium combustion product aerosol was formed, and quickly agglomerated to large (100 to 660 {mu}m) diameter particles. More than 50% of the aerosol mass fell out within several hundred meters of the release point. Two additional tests were performed by releasing sodium through 9.5-mm diameter jets at a height of 30 m. In each test, the sodium jet was aimed horizontally across the wind, and followed a downward parabolic trajectory, releasing burning sodium drops along its track. Again, close-in fallout due to large agglomerates was observed. A substantial amount of unburned sodium fell 30 m to the ground, where it burned. In a third type of test, sodium was burned for 60 min as pool in a 1.5m{sup 2} burn pan at 9 m/s wind velocity. Approximately 30% of the combustion products became airborne. Large agglomerates fell out as they moved downwind, depositing 1 kg/m{sup 2} at 1 m downwind from the edge of the pan. Chemical analysis of the samples indicated that the sodium fires produced mainly Na{sub 2}O, and that the conversion of NaOH was slow. Comparison were made with COMRADEX-IV code models, which are appropriate for calculating deposition and concentrations for downwind distances between 10{sup 2} and 10{sup 4} m. (author)

  9. Combustion of sodium in the open atmosphere

    International Nuclear Information System (INIS)

    Morewith, H.A.; Johnson, R.P.; Nelson, C.T.; Otter, J.M.

    1979-01-01

    A series of sodium fire tests has been conducted in ambient air at a meteorological test site. This test series was designed to simulate hypothetical accidents which might occur in the heat transport system of an LMFBR. Measurements of concentration, agglomeration, fallout, and chemical species of the sodium combustion products were made as a function of downwind distance. In each of the first two tests, ∼23 kg of 540 deg. C sodium was sprayed as a fan of 250-μm sodium drops across the wind, from heights of 5 or 6 m. Each release took a few minutes. A dense sodium combustion product aerosol was formed, and quickly agglomerated to large (100 to 660 μm) diameter particles. More than 50% of the aerosol mass fell out within several hundred meters of the release point. Two additional tests were performed by releasing sodium through 9.5-mm diameter jets at a height of 30 m. In each test, the sodium jet was aimed horizontally across the wind, and followed a downward parabolic trajectory, releasing burning sodium drops along its track. Again, close-in fallout due to large agglomerates was observed. A substantial amount of unburned sodium fell 30 m to the ground, where it burned. In a third type of test, sodium was burned for 60 min as pool in a 1.5m 2 burn pan at 9 m/s wind velocity. Approximately 30% of the combustion products became airborne. Large agglomerates fell out as they moved downwind, depositing 1 kg/m 2 at 1 m downwind from the edge of the pan. Chemical analysis of the samples indicated that the sodium fires produced mainly Na 2 O, and that the conversion of NaOH was slow. Comparison were made with COMRADEX-IV code models, which are appropriate for calculating deposition and concentrations for downwind distances between 10 2 and 10 4 m. (author)

  10. Non-Destructive Testing of Plutonium-Enriched Fuel Rods; Controles non Destructifs de Barreaux Combustibles Enrichis au Plutonium; Nedestruktivnyj-kontrol' toplivnykh sterzhnej''obogashchennykh plutoniem; Ensayo no Destructivo de Elementos Combustibles Enriquecidos en Plutonio

    Energy Technology Data Exchange (ETDEWEB)

    Libotte, P.; Inniger, H.; Leblanc, J. M. [Centre D' Etude de l' Energie Nucleaire, Societe Belge pour l' Industrie Nucleaire, S.A. (Belgonucleaire), Mol (Belgium)

    1965-09-15

    ultrasonically by the pulse-echo technique. The respective advantages of the various non-destructive techniques are studied in relation to the required accuracy and to their possible application to the automated inspection of plutonium fuel rods fabricated on an industrial scale. (author) [French] La Societe belge pour l'industrie nucleaire (BelgoNucleaire) et le Centre d'etude de l'energie nucleaire (CEN) etudient sous contrat, en cooperation avec la Commission de l'EURATOM, l'utilisation du plutonium dans les reacteurs de puissance a eau pressurisee. Dans le cadre des recherches entreprises, differentes techniques de controle non destructif ont ete mises au point en vue d'evaluer la qualite des barreaux combustibles fabriques. Les essais non destructifs mis au point et decrits dans le memoire sont utilises essentiellement pour le controle des dimensions et de la qualite des tubes de gainage, de l'integrite des soudures, de l'etancheite des barreaux, de la densite du materiau combustible et de sa repartition, de l'enrichissement en plutonium et de sa distribution radiale et axiale dans le barreau combustible. Les methodes utilisees pour ces essais non destructifs comportent principalement les examens par radiographie, par autoradiographie, par gammagraphie et par les ultrasons. Le document reprend le principe de chacune des mesures realisees, et decrit dans chaque cas l'appareillage utilise et les techniques operatoires appliquees en vue d'obtenir les sensibilites et precisions desirees. La technique utilisee pour la radiographie permet de deceler des defauts de l'ordre de 50 a 60 {mu}m dans les soudures d'extremite des barreaux combustibles. Les combustibles etant densifies par vibration de trois fractions de poudre dense, dont la fraction fine seule comporte l'enrichissement en plutonium, il est essentiel que la repartition de ce dernier, de meme que la distribution de la densite, soient relevees avec precision. Le comptage du rayonnement gamma emergent emis par le plutonium

  11. A mathematical model for cost of maritime transport. Application to competitiveness of nuclear vessels; Modele mathematique du cout de transport maritime application a la competitivite du navire nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Dorval, C [Commissariat a l' Energie Atomique, 75 - Paris (France)

    1966-05-01

    competitivite, nous considerons deux cas: 1) le tonnage a transporter annuellement est limite; 2) le tonnage a transporter annuellement n'est pas limite. Dans les deux cas, nous recherchons les optima du navire classique et du navire nucleaire, et nous les comparons. Nous construisons les courbes de competitivite en fonction des rapports des couts de combustible nucleaire et classique, et des couts marginaux de la puissance nucleaire et classique. Ces courbes traduisent les valeurs limites des deux rapports ci-dessus pour lesquelles les couts de transport du navire nucleaire et du navire classique sont egaux. Suivant les hypotheses adoptees pour le marche du fret et pour la limite du tonnage transporte annuellement, nous avons des courbes de competitivite tres differentes. De toute facon, c'est l'augmentation de puissance qui favorise le nucleaire. On peut obtenir cette augmentation en accroissant le deplacement ce qui est toujours interessant dans la mesure ou le fret le justifie, et en accroissant la vitesse, mais dans ce cas le modele met en evidence l'existence d'une limite. Le sous-marin peut presenter certains avantages (moindre resistance hydrodynamique de l'eau, possibilite de vitesse plus reguliere, et eventuellement reduction de trajet) qui rendent la competitivite du nucleaire plus aisee. (auteur)

  12. Culture du bambou : diversification des moyens de subsistance des ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Culture du bambou : diversification des moyens de subsistance des petits producteurs de tabac du sud de la province de Nyanza, au Kenya - phase II. Au cours de la première phase du projet (projet no 103765), les chercheurs ont effectué une analyse de marché pour le bambou et les produits du bambou, comparé les ...

  13. Étude comparée du Liber Judiciorum et du Fuero Juzgo

    Directory of Open Access Journals (Sweden)

    Estelle MAINTIER-VERMOREL

    2009-04-01

    Full Text Available Étant donné sa situation géographique, entre l’Europe et le monde arable, la Castille a joué un rôle particulièrement important, au Moyen Âge, dans le cadre des activités de traduction - notamment avec la célèbre École de Tolède ou les ateliers d’Alphonse X. Cette étude est centrée sur l’une de ces traductions, réalisée sous le règne de Ferdinand III, qui a représenté un point de départ dans le passage des textes officiels du latin au romance. Il s’agit du Fuero Juzgo, un ensemble de lois octroyé, pour la première fois, par Ferdinand III en 1241 à la ville de Cordoue et présenté comme la simple traduction du Liber Judiciorum, élaboré cinq siècles plus tôt dans les Conciles wisigothiques. Nous n’aborderons pas ici cette traduction d’un point de vue linguistique, mais historique et politique. Par le biais d’une comparaison détaillée des prologues des deux textes - qui constituent de véritables traités politiques portant sur le rôle du roi et ses relations avec l’Eglise - nous tenterons de démontrer comment le texte a pu être adapté, au travers de changements minimes mais nombreux et systématiques. Nous essaierons également de montrer pourquoi, dans un contexte de réunion entre Castille et León et également de grande extension du territoire, due à la Reconquête, cette réélaboration subtile du contenu peut être imputée à une manipulation à des fins politiques. Une manipulation, qui plus est, dotée d’une orientation très claire, c’est-à-dire en faveur du roi et au détriment de l’Église - un phénomène qui pourrait constituer les prémices de ce que l’on a coutume d’appeler la genèse de l’État moderne.Dada su situación geográfica, entre Europa y el mundo árabe, Castilla tuvo un papel particularmente importante en el marco de las actividades de traducción durante la Edad Media - especialmente con la famosa Escuela de Toledo o los talleres de Alfonso

  14. Numerical modeling of sodium fire – Part II: Pool combustion and combined spray and pool combustion

    International Nuclear Information System (INIS)

    Sathiah, Pratap; Roelofs, Ferry

    2014-01-01

    Highlights: • A CFD based method is proposed for the simulation of sodium pool combustion. • A sodium evaporation based model is proposed to model sodium pool evaporation. • The proposed method is validated against sodium pool experiments of Newman and Payne. • The results obtained using the proposed method are in good agreement with the experiments. - Abstract: The risk of sodium-air reaction has received considerable attention after the sodium-fire accident in Monju reactor. The fires resulting from the sodium-air reaction can be detrimental to the safety of a sodium fast reactor. Therefore, predicting the consequences of a sodium fire is important from a safety point of view. A computational method based on CFD is proposed here to simulate sodium pool fire and understand its characteristics. The method solves the Favre-averaged Navier-Stokes equation and uses a non-premixed mixture fraction based combustion model. The mass transfer of sodium vapor from the pool surface to the flame is obtained using a sodium evaporation model. The proposed method is then validated against well-known sodium pool experiments of Newman and Payne. The flame temperature and location predicted by the model are in good agreement with experiments. Furthermore, the trends of the mean burning rate with initial pool temperature and oxygen concentration are captured well. Additionally, parametric studies have been performed to understand the effects of pool diameter and initial air temperature on the mean burning rate. Furthermore, the sodium spray and sodium pool combustion models are combined to simulate simultaneous spray and pool combustion. Simulations were performed to demonstrate that the combined code could be applied to simulate this. Once sufficiently validated, the present code can be used for safety evaluation of a sodium fast reactor

  15. Numerical modeling of sodium fire – Part II: Pool combustion and combined spray and pool combustion

    Energy Technology Data Exchange (ETDEWEB)

    Sathiah, Pratap, E-mail: pratap.sathiah78@gmail.com [Shell Global Solutions Ltd., Brabazon House, Concord Business Park, Threapwood Road, Manchester M220RR (United Kingdom); Roelofs, Ferry, E-mail: roelofs@nrg.eu [Nuclear Research and Consultancy Group (NRG), Westerduinweg 3, 1755ZG Petten (Netherlands)

    2014-10-15

    Highlights: • A CFD based method is proposed for the simulation of sodium pool combustion. • A sodium evaporation based model is proposed to model sodium pool evaporation. • The proposed method is validated against sodium pool experiments of Newman and Payne. • The results obtained using the proposed method are in good agreement with the experiments. - Abstract: The risk of sodium-air reaction has received considerable attention after the sodium-fire accident in Monju reactor. The fires resulting from the sodium-air reaction can be detrimental to the safety of a sodium fast reactor. Therefore, predicting the consequences of a sodium fire is important from a safety point of view. A computational method based on CFD is proposed here to simulate sodium pool fire and understand its characteristics. The method solves the Favre-averaged Navier-Stokes equation and uses a non-premixed mixture fraction based combustion model. The mass transfer of sodium vapor from the pool surface to the flame is obtained using a sodium evaporation model. The proposed method is then validated against well-known sodium pool experiments of Newman and Payne. The flame temperature and location predicted by the model are in good agreement with experiments. Furthermore, the trends of the mean burning rate with initial pool temperature and oxygen concentration are captured well. Additionally, parametric studies have been performed to understand the effects of pool diameter and initial air temperature on the mean burning rate. Furthermore, the sodium spray and sodium pool combustion models are combined to simulate simultaneous spray and pool combustion. Simulations were performed to demonstrate that the combined code could be applied to simulate this. Once sufficiently validated, the present code can be used for safety evaluation of a sodium fast reactor.

  16. Experimental validation of calculated capture rate for nucleus involved in fuel cycle; Validation experimentale du calcul du taux de capture des noyaux intervenant dans le cycle du combustible

    Energy Technology Data Exchange (ETDEWEB)

    Benslimane-Bouland, A

    1997-09-01

    The framework of this study was the evaluation of the nuclear data requirements for Actinides and Fission Products applied to current nuclear reactors as well as future applications. This last item includes extended irradiation campaigns, 100 % Mixed Oxide fuel, transmutation or even incineration. The first part of this study presents different types of integral measurements which are available for capture rate measurements, as well as the methods used for reactor core calculation route design and nuclear data library validation. The second section concerns the analysis of three specific irradiation experiments. The results have shown the extent of the current knowledge on nuclear data as well as the associated uncertainties. The third and last section shows both the coherency between all the results, and the statistical method applied for nuclear data library adjustment. A relevant application of this method has demonstrated that only specifically chosen integral experiments can be of use for the validation of nuclear data libraries. The conclusion is reached that even if co-ordinated efforts between reactor and nuclear physicists have made possible a huge improvement in the knowledge of capture cross sections of the main nuclei such as uranium and plutonium, some improvements are currently necessary for the minor actinides (Np, Am and Cm). Both integral and differential measurements are recommended to improve the knowledge of minor actinide cross sections. As far as integral experiments are concerned, a set of criteria to be followed during the experimental conception have been defined in order to both reduce the number of required calculation approximations, and to increase as much as possible the maximum amount of extracted information. (author)

  17. Mise en oeuvre des protections électriques dans les réseaux de distribution du CERN

    CERN Document Server

    Delidais, M

    2002-01-01

    Depuis 1957, date de la création de la première sous-station électrique du CERN, le réseau électrique a connu une constante évolution en relation avec l'extension du laboratoire et à la réalisation des nouvelles machines ainsi qu'à une évolution rapide du matériel de distribution électrique ; ce vaste réseau construit sur une période de plus de 40 ans subit encore de profondes transformations et extensions liées au projet LHC et à son adaptation à l'ouverture du marché européen de l'énergie à la concurrence. Les dispositifs de protection des réseaux CERN ont du s'adapter à ces évolutions et aux progrès réalisés dans le domaine des relais de protection, en particulier avec l'introduction des relais électroniques dans les années 1975 puis en 1994 avec la venue des systèmes utilisant les microprocesseurs et des outils de programmation. La transformation des équipements de protection d'origine vers les systèmes actuels sont mis en évidence tant du point de vue du matériel lui-mê...

  18. Positron annihilation in solids: positronium diffusion; Annihilation du positon dans les solides diffusion du positonium

    Energy Technology Data Exchange (ETDEWEB)

    Paulin, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-04-01

    The existence of two slow components in life-time spectrum of positron annihilation in silicium, aluminium and alkaline-earth oxides powders is established. These two long mean-lives {approx_equal} 10{sup -9} s and {approx_equal} 10{sup -7} s result from annihilation, inside and outside the grains respectively, of ortho-positronium formed in defects present in ionic crystals investigated. Dynamic behaviour of Ps, so revealed, is analyzed in terms of diffusion in excellent agreement with experiment. Diffusion constants of the order of 10{sup -4} cm{sup 2} sec{sup -1} and mean path before annihilation from 50 to 300 Angstrom are measured. From 100 to 500 K the temperature influence upon diffusion process is effective only in SiO{sub 2} where activation energy is found about 10{sup -2} eV. The p-Ps zero point energy evaluated by angular correlation gives the order of magnitude for defects dimensions and diffusion mean-time. Finally, o-Ps behaviour in space between grains, where its interaction with atmospheric gases can be only detected, is analysed. (author) [French] Nous mettons en evidence l'existence de deux composantes lentes dans le spectre de temps de vie du positon avant annihilation dans des poudres d'oxydes alcalinoterreux d'alumine et de silice. Ces deux longues vies moyennes {approx_equal} 10{sup -9} s et {approx_equal} 10{sup -7} s resultent respectivement de l'annihilation a l'interieur et a l'exterieur des grains de l'ortho-positonium forme dans certains defauts presents dans les cristaux ioniques etudies. L'analyse des proprietes dynamiques du Ps ainsi revelees, est effectuee en termes de diffusion en excellent accord avec l'experience. Des constantes de diffusion de l'ordre de 10{sup -4} cm{sup 2} sec{sup -1} et des parcours moyens avant annihilation variant de 50 a 300 Angstrom sont ainsi mesures. Entre 100 et 500 K l'influence de la temperature sur le processus de diffusion n'est sensible

  19. COMMUNICATION DU CREDIT AGRICOLE - French version only

    CERN Multimedia

    2003-01-01

    La Direction du Crédit Agricole informe son aimable clientèle du CERN des jours et heures d'ouverture de l'agence du site de Prévessin à compter du mardi 14 janvier 2003 : 1. Horaires pour les opérations bancaires courantes 7 jours sur 7 et 24h/24 avec l'espace libre service bancaire. 2. Horaires conseil du mardi au vendredi - Mardi, de 9h. à 12h. et de 14h.15 à 16h.30. - Mercredi, jeudi et vendredi, de 9h. à 12h. et de 13h.30 à 16h.30. Deux collaboratrices au lieu d'une seront désormais présentes toute la journée du mardi au vendredi pour vous accueillir, vous informer et vous conseiller en crédits et placements (réception conseil sur rendez-vous). Autre nouveauté : les mêmes conseillers seront aussi à votre disposition le samedi, sur notre agence de Gex, de 8h.15 à 13h.05, notamment pour les études de financements habitat. La Direction et toute l'équipe de l'agence du Crédit Agricole vous souhaitent une excellent année 2003.

  20. Nouvelles du Centre Aéré de l’Association du Personnel du CERN

    CERN Multimedia

    Jardin d'enfants

    2015-01-01

    Cet été 2015, durant quatre semaines d’été, le Centre Aéré a accueilli plus de 40 enfants âgés de 4 à 6 ans. Devant le succès rencontré, et à la demande des parents, il a été décidé d’en doubler la capacité maximale. A l'été 2016, du 4 au 29 juillet, la structure pourra accueillir les enfants de 4 ans révolus et de moins de 7 ans (nés après le 31/07/2009 mais avant  01/07/2012). Les inscriptions se feront à la semaine durant le mois d'Avril 2016. Les programmes sont en cours d'élaboration cependant nous pouvons déjà vous communiquer le thème conducteur du centre qui sera : à la découverte d'un continent différent chaque ...

  1. Fluidite de l'huile produite par des arbres du second cycle de ...

    African Journals Online (AJOL)

    Les résultats obtenus indiquent que le matériel végétal Deli x La Mé issu du premier cycle de sélection récurrente réciproque possède un indice d'iode moyen de 55. Les indices d'iode des matériels issus du second cycle de sélection récurrente réciproque, laissent apparaître globalement une amélioration de 2 points pour ...

  2. Some aspects of sulphite metabolism in plants; Quelques aspects du metabolisme du sulfite chez les vegetaux

    Energy Technology Data Exchange (ETDEWEB)

    Perez-Milan, Hernan

    1958-05-15

    As sulphite appears to be an intermediate substance in the degradation of sulphur-containing amino acids, and has an important metabolic role, notably for plants, this research thesis aims at comparing transformations which may occur for a same chemical compound (the sulphite) in various organisms belonging to different species or kingdoms. More particularly, the author studied the formation of sulphite in vegetal tissues, and the oxidisation of sulphite into sulfate within these tissues. In vitro experiments have been performed with oat, while in vivo experiments have been performed on tobacco plants [French] Le sulfite apparait comme une substance intermediaire de la degradation des acides amines soufres. Son role dans la biosynthese de certains d'entre eux, problematique chez les mammiferes, est certain chez les oiseaux, qui, a cet egard, se comportent comme des autotrophes partiels, puisqu'ils reduisent le sulfate en sulfite. On s'apercoit ainsi qu'un degre d'evolution moindre confere au sulfite une importance metabolique plus grande. On peut s'attendre a trouver chez les vegetaux un role encore accru pour le sulfite. Le present travail entre dans ce cadre d'etudes comparees des transformations que peut subir un meme type de compose chimique: le sulfite, dans divers organismes appartenant a des especes ou a des regnes differents. Les donnees acquises exposees ici auront trait aux deux points suivants: I - La formation du sulfite dans les tissus vegetaux, II - L'oxydation dans ces tissus, du sulfite en sulfate. L'avoine nous a servi comme materiel de depart pour les experiences faites in vitro. Cette plante presente en effet l'avantage de se bien cultiver en toutes saisons, de se broyer facilement, et d'etre depourvue au maximum de mucilages, de resines, substances genantes pour l'analyse ulterieure. Les essais faits in vivo, ont mis en oeuvre des plants de tabac, qui permettent une nutrition par le petiole ou par la tige particulierement aisee.

  3. Characterisation of wood combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto

    The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

  4. Combustion instability modeling and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Santoro, R.J.; Yang, V.; Santavicca, D.A. [Pennsylvania State Univ., University Park, PA (United States); Sheppard, E.J. [Tuskeggee Univ., Tuskegee, AL (United States). Dept. of Aerospace Engineering

    1995-12-31

    It is well known that the two key elements for achieving low emissions and high performance in a gas turbine combustor are to simultaneously establish (1) a lean combustion zone for maintaining low NO{sub x} emissions and (2) rapid mixing for good ignition and flame stability. However, these requirements, when coupled with the short combustor lengths used to limit the residence time for NO formation typical of advanced gas turbine combustors, can lead to problems regarding unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions, as well as the occurrence of combustion instabilities. The concurrent development of suitable analytical and numerical models that are validated with experimental studies is important for achieving this objective. A major benefit of the present research will be to provide for the first time an experimentally verified model of emissions and performance of gas turbine combustors. The present study represents a coordinated effort between industry, government and academia to investigate gas turbine combustion dynamics. Specific study areas include development of advanced diagnostics, definition of controlling phenomena, advancement of analytical and numerical modeling capabilities, and assessment of the current status of our ability to apply these tools to practical gas turbine combustors. The present work involves four tasks which address, respectively, (1) the development of a fiber-optic probe for fuel-air ratio measurements, (2) the study of combustion instability using laser-based diagnostics in a high pressure, high temperature flow reactor, (3) the development of analytical and numerical modeling capabilities for describing combustion instability which will be validated against experimental data, and (4) the preparation of a literature survey and establishment of a data base on practical experience with combustion instability.

  5. Coordonnateur du bureau d'assistance | CRDI - Centre de ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Résumé des fonctions. En tant que membre de l'équipe du Bureau d'assistance au sein de la Section du service à la clientèle (SSC), le coordonnateur du Bureau d'assistance offre au personnel du Centre et aux autres utilisateurs reconnus des installations TI du Centre un soutien de première ligne en matière d'utilisation ...

  6. La population du Moyen-Orient et de l'Afrique du Nord contribue ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    29 avr. 2016 ... Le degré d'apport au contenu varie grandement d'une population à l'autre. Si les habitants du Moyen-Orient et de l'Afrique du Nord (région MENA) utilisent Wikipédia, ils y contribuent cependant moins que les populations d'autres régions du monde. Le contenu au sujet de la région MENA est, le plus ...

  7. L'action du CRDI — le développement du secteur privé

    International Development Research Centre (IDRC) Digital Library (Canada)

    Cathy Egan

    Le CRDI est du nombre. Il reconnaît depuis longtemps la valeur de l'industrie, des échanges et du commerce comme moteurs de la croissance économique. Grâce au soutien concret qu'il a accordé au développement du secteur privé, le CRDI a appris que deux types d'aide peuvent porter fruit : améliorer le con- texte dans ...

  8. Improvement of fuel combustion technologies

    Energy Technology Data Exchange (ETDEWEB)

    Tumanovskii, A.G.; Babii, V.I.; Enyakin, Y.P.; Kotler, V.R.; Ryabov, G.V.; Verbovetskii, E.K.; Nadyrov, I.I. [All-Russian Thermal Engineering Institute, Moscow (Russian Federation)

    1996-07-01

    The main problems encountered in the further development of fuel combustion technologies at thermal power stations in Russia are considered. Experience is generalized and results are presented on the efficiency with which nitrogen oxide emissions are reduced by means of technological methods when burning natural gas, fuel oil, and coal. The problems that arise in the introduction of new combustion technologies and in using more promising grades of coal are considered. The results studies are presented that show that low grade Russian coals can be burnt in circulating fluidized bed boilers. 14 refs., 5 figs., 4 tabs.

  9. Chemical kinetics and combustion modeling

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J.A. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to gain qualitative insight into how pollutants are formed in combustion systems and to develop quantitative mathematical models to predict their formation rates. The approach is an integrated one, combining low-pressure flame experiments, chemical kinetics modeling, theory, and kinetics experiments to gain as clear a picture as possible of the process in question. These efforts are focused on problems involved with the nitrogen chemistry of combustion systems and on the formation of soot and PAH in flames.

  10. Etude de la structure et du comportement en cristallisation d'un verre nucléaire d'aluminoborosilicate de terre rare

    OpenAIRE

    Quintas , Arnaud

    2007-01-01

    Ce travail de thèse porte sur l'étude d'un verre aluminoborosilicate de terre rare de composition molaire 61,81 SiO2 - 3,05 Al2O3 - 8,94 B2O3 - 14,41 Na2O - 6,33 CaO - 1,90 ZrO2 - 3,56 Nd2O3, destiné au confinement des déchets issus du retraitement de combustibles nucléaires usagés à haut taux de combustion. Au niveau structural, nous nous sommes intéressés principalement au rôle des ions modificateurs sur l'organisation du réseau vitreux par le biais de différents changements de composition ...

  11. Application of the FIRST Combustion model to Spray Combustion

    NARCIS (Netherlands)

    de Jager, B.; Kok, Jacobus B.W.

    2004-01-01

    Liquid fuel is of interest to apply to gas turbines. The large advantage is that liquids are easily storable as compared to gaseous fuels. Disadvantage is that liquid fuel has to be sprayed, vaporized and mixed with air. Combustion occurs at some stage of mixing and ignition. Depending on the

  12. Development of a Premixed Combustion Capability for Scramjet Combustion Experiments

    Science.gov (United States)

    Rockwell, Robert D.; Goyne, Christopher P.; Rice, Brian E.; Chelliah, Harsha; McDaniel, James C.; Edwards, Jack R.; Cantu, Luca M. L.; Gallo, Emanuela C. A.; Cutler, Andrew D.; Danehy, Paul M.

    2015-01-01

    Hypersonic air-breathing engines rely on scramjet combustion processes, which involve high speed, compressible, and highly turbulent flows. The combustion environment and the turbulent flames at the heart of these engines are difficult to simulate and study in the laboratory under well controlled conditions. Typically, wind-tunnel testing is performed that more closely approximates engine testing rather than a careful investigation of the underlying physics that drives the combustion process. The experiments described in this paper, along with companion data sets being developed separately, aim to isolate the chemical kinetic effects from the fuel-air mixing process in a dual-mode scramjet combustion environment. A unique fuel injection approach is taken that produces a nearly uniform fuel-air mixture at the entrance to the combustor. This approach relies on the precombustion shock train upstream of the dual-mode scramjet combustor. A stable ethylene flame anchored on a cavity flameholder with a uniformly mixed combustor inflow has been achieved in these experiments allowing numerous companion studies involving coherent anti-Stokes Raman scattering (CARS), particle image velocimetry (PIV), and planar laser induced fluorescence (PLIF) to be performed.

  13. Sulphite metabolism; Metabolisme du sulfite

    Energy Technology Data Exchange (ETDEWEB)

    Fromageot, P; Chapeville, F [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Although the formation of sulphite by micro-organisms was observed as early as 1914 by Neuberg, it was only in 1932 that Nightingale showed it to be present inside cells, in the case of tomato leaf stalks, its formation being due to the reaction: SO{sub 3}H{sup -} + (S{sub 2}O{sub 3}){sub 2}{sup --} {yields} S{sub 2}O{sub 3}{sup --} + O{sub 3}S{sub 2}O{sub 3}{sup --}. The presence of the thiosulphate formed was shown by the high refractive index of its barium salt. Today we have a certain amount of data concerning the formation and use of sulphite in the living cell, even through the knowledge is still incomplete. In this article we will describe and discuss the facts which are known, with particular reference to the oxidation of sulphite. (author) [French] Si la formation de sulfite par des micro-organismes a ete observee des 1914 par Neuberg, sa presence a l'interieur des cellules a ete demontree pour la premiere fois par Nightingale en 1932, dans des tiges et des feuilles de tomates, par la reaction: SO{sub 3}H{sup -} + (S{sub 2}O{sub 3}){sub 2}{sup --} {yields} S{sub 2}O{sub 3}{sup --} + O{sub 3}S{sub 2}O{sub 3}{sup --}. Le thiosulfate forme etait mis en evidence par l'indice de refraction eleve de son sel de baryum. Aujourd'hui on possede un certain nombre de donnees, cependant encore tres incompletes, sur la formation du sulfite et son utilisation par la cellule vivante. Dans cet expose nous decrirons et discuterons quelques-unes de ces acquisitions, tout particulierement celles relatives a l'oxydation du sulfite. (auteur)

  14. Relations entre acides gras oméga-3, oméga-9, structures et fonctions du cerveau. Le point sur les dernières données. Le coût financier alimentaire des oméga-3 « Je chercherai à connaître les différences qui existent entre les huiles de faine, de colza, d’olive, de noix ». Honoré de Balzac. « Histoire de César Birotteau ».

    Directory of Open Access Journals (Sweden)

    Bourre Jean-Marie

    2003-05-01

    de l’audition, de la vue et de l’odorat résulte tout autant de la diminution de l’efficacité des parties concernées du cerveau que des perturbations des récepteurs sensoriels, en particulier de l’oreille interne ou de la rétine. Un niveau de perception donné du goût du sucré exige, par exemple, une quantité de sucre plus grande chez ceux qui sont déficients en cet acide gras. Le déficit en ω6 n’étant pas encore observé, compte tenu des habitudes alimentaires, son impact sur le cerveau n’a pas été étudié. En revanche, une carence en acides gras ω9, spécifiquement en acide oléique, induit une réduction de cet acide dans nombre de tissus, excepté le cerveau (mais le nerf sciatique est touché. Ainsi, cet acide ne serait pas synthétisé en quantité suffisante, au moins pendant la période de gestation-lactation, impliquant une obligation d’apport alimentaire. Cette revue fait le point des meilleures sources d’apport en acides gras ω3, elle évalue l’ampleur des enrichissements qui peuvent être réalisés en modifiant la nourriture donnée aux animaux : modeste effet pour les ruminants, appréciables pour les viandes de porc, de lapin et de volaille ; considérable pour les oeufs et les poissons. L’impact sur la couverture des besoins de l’homme est déterminé, ainsi que les conséquences pour sa santé. Pour la première fois, le coût pour le consommateur est précisé, en classant les principaux aliments par rapport au prix des ω3 qu’ils contiennent.

  15. Interactive wood combustion for botanical tree models

    KAUST Repository

    Pirk, Sö ren; Jarząbek, Michał; Hadrich, Torsten; Michels, Dominik L.; Palubicki, Wojciech

    2017-01-01

    We present a novel method for the combustion of botanical tree models. Tree models are represented as connected particles for the branching structure and a polygonal surface mesh for the combustion. Each particle stores biological and physical

  16. Free Energy and Internal Combustion Engine Cycles

    OpenAIRE

    Harris, William D.

    2012-01-01

    The performance of one type (Carnot) of Internal Combustion Engine (ICE) cycle is analyzed within the framework of thermodynamic free energies. ICE performance is different from that of an External Combustion Engine (ECE) which is dictated by Carnot's rule.

  17. Method for storing radioactive combustible waste

    Science.gov (United States)

    Godbee, H.W.; Lovelace, R.C.

    1973-10-01

    A method is described for preventing pressure buildup in sealed containers which contain radioactively contaminated combustible waste material by adding an oxide getter material to the container so as to chemically bind sorbed water and combustion product gases. (Official Gazette)

  18. Scramjet Combustion Stability Behavior Modeling, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the potential to predict the combustion stability of a scramjet. This capability is very...

  19. Scramjet Combustion Stability Behavior Modeling, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the means to accurately predict the combustion stability of a scramjet. This capability is very...

  20. Publication sites productive uses of combustion ash

    Science.gov (United States)

    Publication Sites Productive Uses of Combustion Ash For more information contact: e:mail: Public waste combustion ash in landfills. The new technology brief describes recent studies where ash was used

  1. Combustion Research Facility | A Department of Energy Office of Science

    Science.gov (United States)

    Collaborative Research Facility Back to Sandia National Laboratory Homepage Combustion Research Search the CRF Combustion Chemistry Flame Chemistry Research.Combustion_Chemistry.Flame_Chemistry Theory and Modeling Theory and Modeling Combustion Kinetics High Pressure Chemistry Chemistry of Autoignition

  2. Fuel Combustion and Engine Performance | Transportation Research | NREL

    Science.gov (United States)

    Fuel Combustion and Engine Performance Fuel Combustion and Engine Performance Photo of a gasoline emissions in advanced engine technologies. Photo by Dennis Schroeder, NREL NREL's combustion research and combustion and engine research activities include: Developing experimental and simulation research platforms

  3. Optimization of fuel cycles: marginal loss values; Optimisation des cycles de combustibles: valeurs marginales des pertes

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J. [Commissariat a l' Energie Atomique, 75 - Paris (France); Lasteyrie, B. de; Doumerc, J. [Compagnie pour l' Etude et la Realisation de Combustibles Atomiques, 75 - Paris (France)

    1965-07-01

    Uranium processing from the pit to the fuel element rod entails metal losses at every step. These losses become more and more expensive with the elaboration of the metal. Some of the uranium must be accepted as definitely lost whilst the rest could be recovered and recycled. The high cost of these losses, whether they are recycled or not, and the fact that the higher the enrichment is the higher their costs are, make it necessary to take them into account when optimizing fuel cycles. It is therefore felt important to determine their most desirable level from an economic point of view at the various nuclear fuel processing stages. However, in France as in some other countries, fissile material production is a state concern, whilst fuel element fabrication is carried out by private enterprise. Optimization criteria and the economic value of losses are therefore different for each of the two links in the fabrication chain. One can try in spite of this to reach an optimum which would conform to public interest, without interfering with the firm's sales policy. This entails using the fact that for a given output marginal costs are equal at the optimum. One can therefore adjust the level of the losses to attain this equation of marginal costs, as these are easier to obtain from the firm than a justification of the actual prices. One notices moreover that, although mainly concerned with losses, this global analysis can bring both the state and the firm to a better use of other production factors. An account is given of the theory of this economic optimization method and practical applications in the field of natural uranium-graphite moderated and CO{sub 2} cooled reactor fuel element fabrication are offered. (authors) [French] L'elaboration de l'uranium, de la mine a la cartouche d'element combustible, s'accompagne, a tous les stades, de pertes, de plus en plus onereuses, a mesure que le metal devient plus elabore. Une certaine proportion de l

  4. Dispersions of Oxides in Oxide Matrices as High-Temperature Reactor Fuels; Dispersions d'oxyde dans des matrices d'oxyde, utilisees comme combustibles dans des reacteurs a haute temperature; Dispersiya okisej v okislovykh matritsakh v kachestve topliva dlya vysokotemperaturnogo reaktora; Empleo de dispersiones de oxidos en matrices de oxidos, como combustibles para reactores de elevada temperatura

    Energy Technology Data Exchange (ETDEWEB)

    Williams, J. [Atomic Energy Research Establishment, Harwell (United Kingdom)

    1963-11-15

    The potential usefulness of dispersions of PuO{sub 2}, UO{sub 2} and ThO{sub 2} in matrices of BeO, Al{sub 2}O{sub 3}, MgO and SiO{sub 2} is reviewed in terms of fuel integrity and fabrication. Dimensional stability and fission-product retentivity are the two features most important to fuel integrity. Compatibility of the constituents of the fuels with one another and with the coolant will influence dimensional stability, but oxide fuels are well favoured in these respects. Dimensional changes under irradiation will contain contributions from neutron and fission fragment damage to the matrix, from radiation damage to the fissile-fertile phase and from agglomerated fission-product gases. Thermal stresses are also capable of effecting changes in shape. However, information on mechanisms for stress relaxation is too limited to enable any reasonable theoretical assessment of behaviour to be made. Both light irradiation and high burn-up studies of fission-product release from the fissile-fertile oxides have concerned themselves mainly with the gaseous products, chiefly xenon. Data on the release of other fission products is very limited as is also information on the movement of fission products in general through the potential matrix materials. Studies of the permeability of sintered pure oxides indicate that densities of at least 95% theoretical density (maybe even 98%) will be needed to eliminate open porosity in such matrices. A variety of techniques are available for the preparation of fissile-fertile particles, for their coating and for their incorporation into high-density matrices. Work on laboratory-scale fabrication processes is well advanced. (author) [French] L'auteur examine la possibilite d'utiliser des combustibles disperses - PuO{sub 2}, UO{sub 2} et ThO{sub 2} et matrices de BeO, Al{sub 2}O{sub 3}, MgO et SiO{sub 2} - dans des reacteurs a haute temperature, au point de vue de l'integrite du combustible et de sa transformation. La stabilite dimensionnelle

  5. Monnaie du commun et revenu social garanti

    OpenAIRE

    Baronian, Laurent; Vercellone, Carlo

    2015-01-01

    Le but de cet article est de poser les bases d’une approche de la monnaie du commun à partir d’une interrogation évincée par la théorie économique des biens communs. Notre analyse de la relation entre monnaie et théorie du commun s’articulera en trois parties. Dans la première, il s’agit d’établir une conception dynamique du commun au singulier dans laquelle la question de la monnaie et des mutations de la division du travail occupe une place centrale. Cette démarche fondée sur la triade trav...

  6. Paysans du Brésil

    Directory of Open Access Journals (Sweden)

    Dominique Temple

    2007-01-01

    Full Text Available Eric Sabourin, « Paysans du Brésil : Entre échange marchand et réciprocité » Paris, Editions Quae, 241p, 30 euros, (préface de Maxime Haubert, 2007Dans la présentation du livre, Maxime Haubert dit :«Cet ouvrage propose une analyse socio-anthropologique et agronomique des sociétés rurales et paysannes du Brésil et des transformations qu'elles ont connues ces dernières décennies, en particulier face aux interventions de l'Etat et à l'expansion du marché capitaliste (.... «Le livre pose d'abor...

  7. Daphne du Maurier' unustatud jutud / Udo Uibo

    Index Scriptorium Estoniae

    Uibo, Udo, 1956-

    2011-01-01

    Ajalehe "The Independent" teatel kavatseb kirjastus "Virago" maikuus avaldada Daphne Du Maurier lühiproosa kogumiku "Nukk" (The Doll), mille on koostanud tema loomingu suur austaja Ann Willmore ja mis sisaldab 13 unustatud ja seni avaldamata novelli

  8. Sociologie du travail et critique du temps industriel The Sociology of Labor and a critical vision of industrial Time

    Directory of Open Access Journals (Sweden)

    Jens Thoemmes

    2009-07-01

    Full Text Available La sociologie du travail a développé un point de vue particulier sur l'analyse des temporalités sociales. L'objectif de cet article est de montrer l'élaboration progressive d'une critique d'un temps industriel unique et unifiant. Cette critique s'appuie sur trois éléments : la multiplicité des temporalités de l’activité professionnelle, le caractère déstructurant du travail industriel et l'émergence d'un temps des loisirs. Ce point de vue a été élaboré par la sociologie du travail en France après 1945, notamment par Georges Friedmann, Pierre Naville et William Grossin.  Avant d’aborder cette période nous voudrions  interroger le moment de la fondation de la sociologie. En mobilisant des travaux peu connus de Max Weber sur le travail, nous verrons en quoi il est un précurseur de l’analyse des attitudes diversifiées des individus et des collectifs à l’égard du temps. Cette perspective lie, dès les premières enquêtes sociologiques, le travail industriel à une interrogation sur les temporalités.The sociology of work and labor developed a particular viewpoint on the analysis of social times. The objective of this article is to show how a criticism of a unique and unifying industrial time progressively grew up. Such criticism leans on three elements: the multiplicity of social times linked to the occupational activity, the disintegrating nature of work in the manufacturing process and the emergence of leisure-time. This point of view was elaborated by the sociology of work in France after 1945, notably by Georges Friedmann, Pierre Naville and William Grossin. Before approaching this period we question the moment of the foundation of sociology. By mobilizing little known research by Max Weber on the manufacturing process, we shall see in what way he was a precursor of the analysis of diversified attitudes regarding time by individuals and groups.

  9. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    NARCIS (Netherlands)

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion

  10. A Pulverized Coal-Fired Boiler Optimized for Oxyfuel Combustion Technology

    Directory of Open Access Journals (Sweden)

    Tomáš Dlouhý

    2012-01-01

    Full Text Available This paper presents the results of a study on modifying a pulverized coal-fired steam boiler in a 250 MWe power plant for oxygen combustion conditions. The entry point of the study is a boiler that was designed for standard air combustion. It has been proven that simply substituting air by oxygen as an oxidizer is not sufficient for maintaining a satisfactory operating mode, not even with flue gas recycling. Boiler design optimization aggregating modifications to the boiler’s dimensions, heating surfaces and recycled flue gas flow rate, and specification of a flue gas recycling extraction point is therefore necessary in order to achieve suitable conditions for oxygen combustion. Attention is given to reducing boiler leakage, to which external pre-combustion coal drying makes a major contribution. The optimization is carried out with regard to an overall power plant conception for which a decrease in efficiency due to CO2 separation is formulated.

  11. Presence de Carbone-13 dans les elements combustibles de type (U,Pu)O 2 irradies en reacteur rapide

    Science.gov (United States)

    Kryger, Bernard; Hagemann, Robert

    1982-06-01

    Du carbone-13 produit par la réaction de capture neutronique 168O + 10n → 136C + 42He se forme dans les combustibles de type oxyde irradiés en neutrons rapides. Cette réaction, dont le seuil d'énergie se situe à 2.35 MeV, conduit à la formation d'une quantité de carbone-13 qui peut varier notablement suivant le spectre neutronique du réacteur (entre 20 et 40 × 10 -6g 13C/g (U,Pu)O 2 pour une fluence de 2 × 10 23 n/cm 2). DES mesures effectuées sur le combustible et la gaine par spectrométrie de masse après irradiation montrent qu'une fraction égale ou supérieure à la moitié du carbone-13 produit dans l'oxyde peut être transférée dans la gaine. Un tel comportement nous fait considérer le carbone-13 comme un véritable marqueur du carbone plus généralement contenu dans l'oxyde et, à ce titre, la détection de cet isotope devrait contribuer à élucider tout particulièrement les mécanismes de carburation de la gaine par les combustibles (U,Pu)O 2 des réacteurs surgénérateurs.

  12. VALEUR PATRIMONIALE DE SERRASALMINAE HERBIVORES DU HAUT MARONI (GUYANE FRANÇAISE : APPROCHES BIOLOGIQUE ET SOCIOCULTURELLE EN PAYS WAYANA.

    Directory of Open Access Journals (Sweden)

    PAGEZY H.

    2002-01-01

    Full Text Available La valeur patrimoniale des kumaru, espèces de poissons appartenant à la sous-famille des Serrasalminae, a été approchée selon des critères faisant référence à leur place au sein de la biodiversité ou de la sociodiversité. Du point de vue de l’anthropologue, les kumaru apparaissent indéniablement comme les espèces de poissons ayant globalement les plus fortes valeurs sociale, hédonique, économique, non seulement chez les Amérindiens Wayana du Haut Maroni, mais aussi chez les Noirs Boni du cours moyen. On peut les qualifier à ce titre d’espèces patrimoniales. Du point de vue du biologiste, les trois espèces de kumaru du Haut Maroni se situent à des niveaux d’endémicité différents, mais toutes participent au fonctionnement du biotope particulier des herbiers à Podostemaceae, au moins dans leurs jeunes stades. Au-delà de la simple conservation des espèces, le mode de distribution de l’asitau (Prosomyleus rhomboidalis et la position du watau yaikë (Tometes lebaili dans la phylogénie des Serrasalminae leur confèrent un ensemble de qualités entrant dans l’évaluation de leur valeur patrimoniale. L’habitat de ces espèces, milieu fragile et très particulier, participe aussi à la patrimonialité.

  13. Aux frontières du politique et du religieux

    Directory of Open Access Journals (Sweden)

    Frédéric Sylvanise

    2006-05-01

    Full Text Available The Autobiography of Miss Jane Pittman met en scène de manière spectaculaire deux figures de leadership noir-américain au XIXe siècle (Ned et au XXe siècle (Jimmy. Ned, fils adoptif de Jane Pittman, se rebaptise Professor Douglass en hommage au leader abolitionniste Frederick Douglass. S’il est fondamentalement laïc (il est instituteur, le texte lui confère néanmoins une dimension religieuse, notamment dans le chapitre intitulé « The Sermon at the River » , qui renvoie à la fois à Moïse (le fleuve et à Jésus (le sermon sur la montagne. Abattu par un tueur à gages, Ned est un martyr dont l’histoire était déjà écrite. Le personnage de Jimmy, attendu par toute une communauté comme le messie (alors que lui aussi est un laïc et un homme qui perd la foi, s’inscrit dans la même histoire. Lettré, éloquent et impliqué dans le mouvement pour les droits civils, il est assassiné comme son prédécesseur. Dans les deux cas, le texte lie donc le politique et le biblique comme s’il ne faisait qu’un : être un leader politique, c’est être un preacher et un messie qui guide le peuple. Il est possible de lire l’évocation de ces deux hommes à la lumière d’une certaine actualité. Ned et Jimmy connaissent en effet un sort proche de celui de Malcolm X et de Martin Luther King, récemment assassinés au moment de l’écriture de The Autobiography of Miss Jane Pittman. C’est l’histoire de la répression du leadership noir, au travers du portrait de deux de ses avatars, qui peut donc se lire en creux ici.

  14. Complications du traitement traditionnel des fractures : aspects ...

    African Journals Online (AJOL)

    Tous les patients reçus avec des complications du traitement traditionnel des fractures ont été inclus dans ce travail. Le diagnostic des lésions était clinique et radiologique. Nous avions reçu 51 patients porteurs de complications suite à des traitements de médecine traditionnelle, soit 13,7% du total des patients hospitalisés ...

  15. Le désordre du monde

    African Journals Online (AJOL)

    sulaiman.adebowale

    Le début du XXIe siècle se caractérise par l'accumulation et la consécution ..... Unis a présidé à la naissance aux forceps de cet outil d'équilibre du monde en ... De toute évidence, l'ONU reste l'instrument qui a marqué le siècle dernier,.

  16. Leaching from biomass combustion ash

    DEFF Research Database (Denmark)

    Maresca, Alberto; Astrup, Thomas Fruergaard

    2014-01-01

    The use of biomass combustion ashes for fertilizing and liming purposes has been widely addressed in scientific literature. Nevertheless, the content of potentially toxic compounds raises concerns for a possible contamination of the soil. During this study five ash samples generated at four...

  17. An incinerator for combustable radwastes

    International Nuclear Information System (INIS)

    Li Jingquan; Jiang Yun; Zhang Yinsheng; Chen Boling; Zhang Shihang

    1989-01-01

    An incinerator has been built up in Shanghai. In this paper, the devices of the incinerator, main parameters of the process, and the results of non-radioactive waste and simulated radwaste combustion tests were contributed. That provides reference information for radwaste treatment with incineration process

  18. 75 FR 32142 - Combustible Dust

    Science.gov (United States)

    2010-06-07

    .... Contact Mat Chibbaro, P.E., Fire Protection Engineer, Office of Safety Systems, OSHA Directorate of..., and metals (such as aluminum and magnesium). Industries that may have combustible dust hazards include..., chemical manufacturing, textile manufacturing, furniture manufacturing, metal processing, fabricated metal...

  19. Sulfur Chemistry in Combustion II

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Kiil, Søren

    2000-01-01

    Several options are available to control the emission of SO2 from combustion processes. One possibility is to use a cleaner technology, i.e. fuel switching from oil and coal to natural gas or biomass, or to desulphurize coal and oil. Another possibility is to change to a different technology...

  20. Multi-zone modelling of PCCI combustion

    NARCIS (Netherlands)

    Egüz, U.; Somers, L.M.T.; Leermakers, C.A.J.; Goey, de L.P.H.

    2011-01-01

    Early Direct Injection Premixed Charge Compression Ignition (EDI PCCI) combustion is a promising concept for the diesel combustion. Although EDI PCCI assures very low soot and NO xemission levels, the injection is uncoupled from combustion, which narrows down the operating conditions. The main

  1. An Assessment of Combustion Dynamics in a Low-Nox, Second-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

    Science.gov (United States)

    Tacina, K. M.; Chang, C. T.; Lee, P.; Mongia, H.; Podboy, D. P.; Dam, B.

    2015-01-01

    Dynamic pressure measurements were taken during flame-tube emissions testing of three second-generation swirl-venturi lean direct injection (SV-LDI) combustor configurations. These measurements show that combustion dynamics were typically small. However, a small number of points showed high combustion dynamics, with peak-to-peak dynamic pressure fluctuations above 0.5 psi. High combustion dynamics occurred at low inlet temperatures in all three SV-LDI configurations, so combustion dynamics were explored further at low temperature conditions. A point with greater than 1.5 psi peak-to-peak dynamic pressure fluctuations was identified at an inlet temperature of 450!F, a pressure of 100 psia, an air pressure drop of 3%, and an overall equivalence ratio of 0.35. This is an off design condition: the temperature and pressure are typical of 7% power conditions, but the equivalence ratio is high. At this condition, the combustion dynamics depended strongly on the fuel staging. Combustion dynamics could be reduced significantly without changing the overall equivalence ratio by shifting the fuel distribution between stages. Shifting the fuel distribution also decreased NOx emissions.

  2. Method and device for diagnosing and controlling combustion instabilities in internal combustion engines operating in or transitioning to homogeneous charge combustion ignition mode

    Science.gov (United States)

    Wagner, Robert M [Knoxville, TN; Daw, Charles S [Knoxville, TN; Green, Johney B [Knoxville, TN; Edwards, Kevin D [Knoxville, TN

    2008-10-07

    This invention is a method of achieving stable, optimal mixtures of HCCI and SI in practical gasoline internal combustion engines comprising the steps of: characterizing the combustion process based on combustion process measurements, determining the ratio of conventional and HCCI combustion, determining the trajectory (sequence) of states for consecutive combustion processes, and determining subsequent combustion process modifications using said information to steer the engine combustion toward desired behavior.

  3. Perspectives d'amélioration du rendement à très faible charge des moteurs d'automobile Prospects for Lmprovinq the Very-Low-Load Efficiency of Automotive Engines

    Directory of Open Access Journals (Sweden)

    Douaud A.

    2006-11-01

    Full Text Available Le mauvais rendement énergétique des véhicules utilisés à très faible charge (circulation urbaine, vitesses limitées provient entre autres des combustions non optimales. Celles-ci sont de plusieurs types : combustion lente et/ou tardive, ratés de propagation. L'acquisition de cycles de pression au moyen du système DIGITAP développé à l'In-titut Français du Pétrole (IFP est décrite et le calcul instantané du travail cycle-à-cycle permet de définir un critère de stabilité de fonctionnement du moteur. L'analyse thermodynamique des cycles montre que la composition du mélange air + carburant + gaz résiduels, trop proche des limites de propagabilité de flamme, est à l'origine des phénomènes observés. Des voies d'action portant sur les gaz résiduels, la turbulence et les paramètres du système d'allumage sont dégagées et permettent des améliorations importantes du rendement. The poor energy efficiency of vehicles used at very low engine load (urban traffic, limited speeds comes from non-optimum combustion, among other causes. Such combustion may be of several types, i. e. slow and/or late combustion, propagation misfiring. The recording of pressure cycles by the DIGITAP system developed at Institut Français du Pétrole (IFP is described, and the instantaneous computing of the cycle-to-cycle work enables a stability criterion for engine operating to be described. The thermodynamic analysis of the cycles shows that the composition of the air + fuel + residuel gas mixture which is too close to flame propagation limits is at the origin of the phenomena observed. Methods of action concerning residual gases, turbulence and the parameters of the ignition system are determined and make for great improvements in efficiency and stability for such types of running.

  4. Combustor nozzle for a fuel-flexible combustion system

    Science.gov (United States)

    Haynes, Joel Meier [Niskayuna, NY; Mosbacher, David Matthew [Cohoes, NY; Janssen, Jonathan Sebastian [Troy, NY; Iyer, Venkatraman Ananthakrishnan [Mason, OH

    2011-03-22

    A combustor nozzle is provided. The combustor nozzle includes a first fuel system configured to introduce a syngas fuel into a combustion chamber to enable lean premixed combustion within the combustion chamber and a second fuel system configured to introduce the syngas fuel, or a hydrocarbon fuel, or diluents, or combinations thereof into the combustion chamber to enable diffusion combustion within the combustion chamber.

  5. Coal combustion waste management study

    International Nuclear Information System (INIS)

    1993-02-01

    Coal-fired generation accounted for almost 55 percent of the production of electricity in the United States in 1990. Coal combustion generates high volumes of ash and flue gas desulfurization (FGD) wastes, estimated at almost 90 million tons. The amount of ash and flue gas desulfurization wastes generated by coal-fired power plants is expected to increase as a result of future demand growth, and as more plants comply with Title IV of the 1990 Clean Air Act Amendments. Nationwide, on average, over 30 percent of coal combustion wastes is currently recycled for use in various applications; the remaining percentage is ultimately disposed in waste management units. There are a significant number of on-site and off-site waste management units that are utilized by the electric utility industry to store or dispose of coal combustion waste. Table ES-1 summarizes the number of disposal units and estimates of waste contained at these unites by disposal unit operating status (i.e, operating or retired). Further, ICF Resources estimates that up to 120 new or replacement units may need to be constructed to service existing and new coal capacity by the year 2000. The two primary types of waste management units used by the industry are landfills and surface impoundments. Utility wastes have been exempted by Congress from RCRA Subtitle C hazardous waste regulation since 1980. As a result of this exemption, coal combustion wastes are currently being regulated under Subtitle D of RCRA. As provided under Subtitle D, wastes not classified as hazardous under Subtitle C are subject to State regulation. At the same time Congress developed this exemption, also known as the ''Bevill Exclusion,'' it directed EPA to prepare a report on coal combustion wastes and make recommendations on how they should be managed

  6. Modeling of Plasma Assisted Combustion

    Science.gov (United States)

    Akashi, Haruaki

    2012-10-01

    Recently, many experimental study of plasma-assisted combustion has been done. However, numerous complex reactions in combustion of hydrocarbons are preventing from theoritical study for clarifying inside the plasma-assisted combustion, and the effect of plasma-assist is still not understood. Shinohara and Sasaki [1,2] have reported that the shortening of flame length by irradiating microwave without increase of gas temperature. And they also reported that the same phenomena would occur when applying dielectric barrier discharges to the flame using simple hydrocarbon, methane. It is suggested that these phenomena may result by the electron heating. To clarify this phenomena, electron behavior under microwave and DBD was examined. For the first step of DBD plasma-assisted combustion simulation, electron Monte Carlo simulation in methane, oxygen and argon mixture gas(0.05:0.14:0.81) [2] has been done. Electron swarm parameters are sampled and electron energy distribution function (EEDF)s are also determined. In the combustion, gas temperature is higher(>1700K), so reduced electric field E/N becomes relatively high(>10V/cm/Torr). The electrons are accelerated to around 14 eV. This result agree with the optical emission from argon obtained by the experiment of reference [2]. Dissociation frequency of methane and oxygens are obtained in high. This might be one of the effect of plasma-assist. And it is suggested that the electrons should be high enough to dissociate methane, but plasma is not needed.[4pt] [1] K. Shinohara et al, J. Phys. D:Appl. Phys., 42, 182008 (1-7) (2009).[0pt] [2] K. Sasaki, 64th Annual Gaseous Electronic Conference, 56, 15 CT3.00001(2011).

  7. Combustive management of oil spills

    International Nuclear Information System (INIS)

    1992-01-01

    Extensive experiments with in situ incineration were performed on a desert site at the University of Arizona with very striking results. The largest incinerator, 6 feet in diameter with a 30 foot chimney, developed combustion temperatures of 3000, F, and attendant soot production approximately 1000 times less than that produced by conventional in situ burning. This soot production, in fact, is approximately 30 times less than current allowable EPA standards for incinerators and internal combustion engines. Furthermore, as a consequence of the high temperature combustion, the bum rate was established at a very high 3400 gallons per hour for this particular 6 foot diameter structure. The rudimentary design studies we have carried out relative to a seagoing 8 foot diameter incinerator have predicted that a continuous burn rate of 7000 gallons per hour is realistic. This structure was taken as a basis for operational design because it is compatible with C130 flyability, and will be inexpensive enough ($120,000 per copy) to be stored at those seaside depots throughout the US coast line in which the requisite ancillary equipments (booms, service tugs, etc.) are already deployed. The LOX experiments verified our expectations with respect to combustion of debris and various highly weathered or emulsified oils. We have concluded, however, that the use of liquid oxygen in actual beach clean up is not promising because the very high temperatures associated with this combustion are almost certain to produce environmentally deleterious effects on the beach surface and its immediately sublying structures. However, the use of liquid oxygen augmentation for shore based and flyable incinerators may still play an important role in handing the problem of accumulated debris

  8. Identification d'une loi thermo-élasto-viscoplastique en vue de la modélisation du laminage à chaud du cuivre

    Science.gov (United States)

    Moureaux, P.; Moto Mpong, S.; Remy, M.; Bouffioux, C.; Lecomte-Beckers, J.; Habraken, A. M.

    2002-12-01

    la mise au point d'un modèle de simulation de la dernière passe du laminage à chaud du cuivre ne présente à priori pas de problème du point de vue numérique pour un code d'éléments finis non linéaire. La collecte d'informations précises tant sur le procédé industriel que sur le comportement du matériau est par contre une opération non triviale. Cet article présente les diverses méthodes expérimentales mises en œuvre pour caractériser le matériau : essais de compression à chaud, mesures d'analyse thermique différentielle, essais de dilatométrie et de diffusivité. Les méthodes permettant d'identifier les paramètres de la loi élasto-visco-plastique de type Norton-Hoff à partir des essais sont présentées et une analyse bibliographique investigue le problème de la détermination du module de Young à haute température. Tant les hypothèses supplémentaires relatives au procédé et nécessaires au modèle que les résultats finaux sont résumés.

  9. Combustion synthesis: A new approach for preparation of thermoelectric zinc antimonide compounds

    Energy Technology Data Exchange (ETDEWEB)

    Rouessac, F., E-mail: Florence.Rouessac@univ-montp2.fr [Institut Charles Gerhardt Montpellier, UMR 5253 CNRS-UM2-ENSCM-UM1, C2M Universite Montpellier 2, CC 1504 Place Eugene Bataillon, 34095 Montpellier Cedex 5 (France); Ayral, R.-M. [Institut Charles Gerhardt Montpellier, UMR 5253 CNRS-UM2-ENSCM-UM1, C2M Universite Montpellier 2, CC 1504 Place Eugene Bataillon, 34095 Montpellier Cedex 5 (France)

    2012-07-25

    Highlights: Black-Right-Pointing-Pointer Reliable preparation method of thermoelectric materials. Black-Right-Pointing-Pointer Formation of zinc antimonide by the combustion synthesis method is investigated. Black-Right-Pointing-Pointer XRD and Raman spectroscopy as a function of temperature. Black-Right-Pointing-Pointer SHS: a new way for synthesizing thermoelectric materials. - Abstract: Due to the interesting properties of Zn{sub 4}Sb{sub 3} thermoelectric material, a reliable preparation method of this material is required. In this study, the formation of zinc antimonides by the combustion synthesis method is investigated and subjected to characterization using X-ray diffraction and Raman spectroscopy as a function of temperature. The results show that combustion synthesis can be a new way for synthesizing these thermoelectric materials.

  10. Pru du 2S albumin or Pru du vicilin?

    Science.gov (United States)

    Garino, Cristiano; De Paolis, Angelo; Coïsson, Jean Daniel; Arlorio, Marco

    2015-06-01

    A short partial sequence of 28 amino acids is all the information we have so far about the putative allergen 2S albumin from almond. The aim of this work was to analyze this information using mainly bioinformatics tools, in order to verify its rightness. Based on the results reported in the paper describing this allergen from almond, we analyzed the original data of amino acids sequencing through available software. The degree of homology of the almond 12kDa protein with any other known 2S albumin appears to be much lower than the one reported in the paper that firstly described it. In a publicly available cDNA library we discovered an expressed sequence tag which translation generates a protein that perfectly matches both of the sequencing outputs described in the same paper. A further analysis indicated that the latter protein seems to belong to the vicilin superfamily rather than to the prolamin one. The fact that also vicilins are seed storage proteins known to be highly allergenic would explain the IgE reactivity originally observed. Based on our observations we suggest that the IgE reactive 12kDa protein from almond currently known as Pru du 2S albumin is in reality the cleaved N-terminal region of a 7S vicilin like protein. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Oxyfuel combustion for below zero CO{sub 2} emissions

    Energy Technology Data Exchange (ETDEWEB)

    Boeg Toftegaard, M; Hansen, Kim G; Fisker, D [DONG Energy Power, Hvidovre (Denmark); Brix, J; Brun Hansen, B; Putluru, S S.R.; Jensen, Peter Arendt; Glarborg, Peter; Degn Jensen, A [Technical Univ. of Denmark. CHEC Research Centre, Kgs. Lyngby (Denmark); Montgomery, M [Technical Univ. of Denmark. DTU Mechanical Engineering, Kgs. Lyngby (Denmark)

    2011-07-01

    The reduction of CO{sub 2} emissions is of highest concern in relation to limiting the anthropogenic impacts on the environment. Primary focus has gathered on the large point sources of CO{sub 2} emissions constituted by large heat and power stations and other heavy, energy-consuming industry. Solutions are sought which will enable a significant reduction of the anthropogenic CO{sub 2} emissions during the transformation period from the use of fossil fuels to renewable sources of energy. Carbon capture and storage (CCS) has the potential to significantly reduce CO{sub 2} emissions from power stations while allowing for the continuous utilisation of the existing energy producing system in the transformation period. Oxyfuel combustion is one of the possible CCS technologies which show promising perspectives for implementation in industrial scale within a relatively short period of time. Oxyfuel combustion deviates from conventional combustion in air by using a mixture of pure oxygen and recirculated flue gas as the combustion medium thereby creating a flue gas highly concentrated in CO{sub 2} making the capture process economically more feasible compared to technologies with capture from more dilute CO{sub 2} streams. This project has investigated a number of the fundamental and practical issues of the oxyfuel combustion process by experimental, theoretical, and modelling investigations in order to improve the knowledge of the technology. The subjects investigated cover: general combustion characteristics of coal and biomass (straw) and mixtures thereof, formation and emission of pollutants, ash characteristics, flue gas cleaning for SO{sub 2} by wet scrubbing with limestone and for NO{sub x} by selective catalytic reduction (SCR), corrosion of boiler heat transfer surfaces, operation and control of large suspension-fired boilers, and the perspectives for the implementation of oxyfuel combustion s a CO{sub 2} sequestration solution in the Danish power production

  12. Use of combustible wastes as fuel

    Energy Technology Data Exchange (ETDEWEB)

    Kotler, V.R.; Salamov, A.A.

    1983-01-01

    Achievements of science and technology in creating and using units for combustion of wastes with recovery of heat of the escaping gases has been systematized and generalized. Scales and outlooks are examined for the use of general, industrial and agricultural waste as fuel, composition of the waste, questions of planning and operating units for combustion of solid refuse, settling of waste water and industrial and agricultural waste. Questions are covered for preparing them for combustion use in special units with recovery of heat and at ES, aspects of environmental protection during combustion of waste, cost indicators of the employed methods of recovering the combustible waste.

  13. Les effets du changement climatique dans le bassin du Congo : la ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    22 avr. 2016 ... Dans le bassin du fleuve Congo, plus de 80 % des habitants vivent exclusivement de l'agriculture, de la pêche, de l'élevage et de la cueillette, qui sont des activités largement tributaires du climat.

  14. Engagez-vous, devenez délégué(e) du personnel du CERN

    CERN Multimedia

    Staff Association

    2017-01-01

    Dans notre ECHO N° 275, nous avons annoncé les élections à venir au Conseil du personnel du CERN. Dans le présent ECHO, nous vous informons du lancement du processus des élections qui débute par le dépôt des candidatures. Tous les titulaires, boursiers et associés, qui sont aussi membres de l’Association du personnel, peuvent s’engager et déposer leur candidature entre le 11 septembre à 08 h 00 et le 13 octobre 2017 à 17 h 00. N’hésitez plus, remplissez le formulaire de candidature, présentez-vous aux élections au Conseil du personnel afin de pouvoir représenter et défendre vos collègues du personnel du CERN. ÊTRE DÉLÉGUÉ(E), C’EST QUOI ? Poser la question à plusieurs d...

  15. Homogeneous Charge Compression Ignition Combustion: Challenges and Proposed Solutions

    Directory of Open Access Journals (Sweden)

    Mohammad Izadi Najafabadi

    2013-01-01

    Full Text Available Engine and car manufacturers are experiencing the demand concerning fuel efficiency and low emissions from both consumers and governments. Homogeneous charge compression ignition (HCCI is an alternative combustion technology that is cleaner and more efficient than the other types of combustion. Although the thermal efficiency and NOx emission of HCCI engine are greater in comparison with traditional engines, HCCI combustion has several main difficulties such as controlling of ignition timing, limited power output, and weak cold-start capability. In this study a literature review on HCCI engine has been performed and HCCI challenges and proposed solutions have been investigated from the point view of Ignition Timing that is the main problem of this engine. HCCI challenges are investigated by many IC engine researchers during the last decade, but practical solutions have not been presented for a fully HCCI engine. Some of the solutions are slow response time and some of them are technically difficult to implement. So it seems that fully HCCI engine needs more investigation to meet its mass-production and the future research and application should be considered as part of an effort to achieve low-temperature combustion in a wide range of operating conditions in an IC engine.

  16. Heat transfer and combustion in microgravity; Mujuryokuka deno netsukogaku

    Energy Technology Data Exchange (ETDEWEB)

    Ito, K [Hokkaido University, Sapporo (Japan). Faculty of Engineering

    1994-09-05

    Examples of thermal engineering under gravity free state are introduced. When making semiconductor crystals, the thermal conductivity of the molten substance becomes important but in a microgravity environment where the thermal convection is suppressed, this value can be accurately measured. Although there are many unknown points regarding the thermal conductive mechanism of thermal control equipment elements under microgravity, theoretical analysis is being advanced. It is anticipated that the verification of this theory using liquid droplets will be made. The conveying of boiling heat under microgravity is suppressed because the bubbles stick to the heat source. When a non-azeotropic composition is used, Marangoni convection occurs, and the conveying is promoted. Since there is no thermal convection in microgravity combustion, diffusion dominates. In order to make the phenomenon clear, the free-fall tower can be utilized. A liquid droplet flame will become a complete, integrated, spherical flame. Vaporization coefficient and combustion velocity which are impossible to measure on the ground can be measured. In the case of metal fires occuring in space, the movement of metal dominates the combustion. In microgravity, dust coal will float in a stationary state so the process of combustion can be observed. It is believed that the diffusion flame of hydrocarbons will be thicker than the flame on the ground. 11 refs., 4 figs.

  17. Commis, artisans, ouvriers. Les métamorphoses du salariat dans l’Égypte du XIXe siècle

    Directory of Open Access Journals (Sweden)

    Pascale Ghazaleh

    2012-01-01

    Full Text Available Cet article se propose d’analyser l’évolution du travail salarié en Égypte pendant la première moitié du XIXe siècle à la lumière des modifications apportées au système des charges vénales, qui permet aux sujets du sultan d’accéder au statut de ses serviteurs en achetant le droit de toucher une rémunération. Les réformes juridiques, militaires, économiques et administratives qu’institue Muhammad ‘Alî (r. 1805-1848 en Égypte vont ériger les instances de l’État naissant en source de rémunération et point de référence primaire des détenteurs de charges. Pendant la période 1840-1860, les recrutements de fonctionnaires et de travailleurs connaîtront un repli ; et, lorsque la question du travail salarié est abordée à part entière dans le discours public des années 1880, c’est sous son versant politique, comme métaphore de la tutelle coloniale.

  18. Distributed Low Temperature Combustion: Fundamental Understanding of Combustion Regime Transitions

    Science.gov (United States)

    2016-09-07

    behaviour as compared to ethanol. The latter fuel has also been considered along with methane. Work has also been performed on the further assessment of... behaviour as compared to ethanol. The latter fuel has also been considered along with methane. Work has also been performed on the further assess- ment of...identification of various combustion gas states. A range of Damköhler numbers (Da) from the conventional propagating flamelet regime well into the distributed

  19. Molten salt combustion of radioactive wastes

    International Nuclear Information System (INIS)

    Grantham, L.F.; McKenzie, D.E.; Richards, W.L.; Oldenkamp, R.D.

    1976-01-01

    The Atomics International Molten Salt Combustion Process reduces the weight and volume of combustible β-γ contaminated transuranic waste by utilizing air in a molten salt medium to combust organic materials, to trap particulates, and to react chemically with any acidic gases produced during combustion. Typically, incomplete combustion products such as hydrocarbons and carbon monoxide are below detection limits (i.e., 3 ) is directly related to the sodium chloride vapor pressure of the melt; >80% of the particulate is sodium chloride. Essentially all metal oxides (combustion ash) are retained in the melt, e.g., >99.9% of the plutonium, >99.6% of the europium, and >99.9% of the ruthenium are retained in the melt. Both bench-scale radioactive and pilot scale (50 kg/hr) nonradioactive combustion tests have been completed with essentially the same results. Design of three combustors for industrial applications are underway

  20. The thermo-mechanics of the PWR fuel rod; La thermomecanique du crayon de combustible REP

    Energy Technology Data Exchange (ETDEWEB)

    Barral, J.C. [Electricite de France, EDF, 75 - Paris (France); Gautier, B.; Chaigne, G. [Electricite de France, Service Etudes et Projets Thermiques et Nucleaires, 75 - Paris (France)] [and others

    1999-03-29

    The fuel rod mechanics is of a great importance in the safety and performance of the reactors. In this domain a meeting has been organized by the SFEN the 18 march 1998 at Paris. With the participation of scientists from CEA, EDF and Framatome, the physics of the fuel rods was presented based on four main aspects. Two first papers dealt with the solicitations of the fuel rod in normal and accidental conditions. The physical phenomena under irradiation were then detailed in the four following talks. Three papers presented the simulation and the codes of the fuel-cladding interactions with the diabolo effect. The last paper was devoted to the experiment feedback and the research programs. (A.L.B.)

  1. Evaluation de l'inertie thermique du four a combustible petrole ...

    African Journals Online (AJOL)

    To appreciate time that it is necessary to start and that necessary to cool the kiln with fuel paraffin oil atomised with the water vapour we carried out tests allowing to evaluate its thermal inertia. Thus, the variation of the temperatures according to time was examined during the rise in emperature and the cooling of the kiln.

  2. Transparency associated with the nuclear fuel cycle; Transparence associee au cycle du combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    This document presents the different fuel cycle stages with which the CEA is associated, the annual flow of materials and wastes produced at these different stages, and the destiny of these produced materials and wastes. These information are given for the different CEA R and D activities: experimentation hot laboratories (activities, fuel cycle stages, list of laboratories, tables giving annual flows for each of them), research reactors (types of reactors, fuel usage modes, annual flows of nuclear materials for each reactor), spent fuel management (different types of used materials), spent fuels and radioactive wastes with a foreign origin (quantities, processes)

  3. The ``SILVA`` program; Le cycle du combustible (evolution des techniques d`enrichissement isotopique)

    Energy Technology Data Exchange (ETDEWEB)

    Jacob, M.

    1996-12-31

    The ``SILVA`` process (Uranium Atomic Vapor Laser Isotopic Separation) is an innovating system of enriched uranium (electronuclear reactors fuel) production. Its great interest comes from its selectivity. The aim is to divide by a factor of three the costs of production compared with those of the current plants. The stakes of this research program, its principle, the main research axis, the material means and the future prospects beyond 1997 are given as well as its technical advancement state. (O.M.).

  4. Advancing the Limits of Dual Fuel Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Koenigsson, Fredrik

    2012-07-01

    There is a growing interest in alternative transport fuels. There are two underlying reasons for this interest; the desire to decrease the environmental impact of transports and the need to compensate for the declining availability of petroleum. In the light of both these factors the Diesel Dual Fuel, DDF, engine is an attractive concept. The primary fuel of the DDF engine is methane, which can be derived both from renewables and from fossil sources. Methane from organic waste; commonly referred to as biomethane, can provide a reduction in greenhouse gases unmatched by any other fuel. The DDF engine is from a combustion point of view a hybrid between the diesel and the otto engine and it shares characteristics with both. This work identifies the main challenges of DDF operation and suggests methods to overcome them. Injector tip temperature and pre-ignitions have been found to limit performance in addition to the restrictions known from literature such as knock and emissions of NO{sub x} and HC. HC emissions are especially challenging at light load where throttling is required to promote flame propagation. For this reason it is desired to increase the lean limit in the light load range in order to reduce pumping losses and increase efficiency. It is shown that the best results in this area are achieved by using early diesel injection to achieve HCCI/RCCI combustion where combustion phasing is controlled by the ratio between diesel and methane. However, even without committing to HCCI/RCCI combustion and the difficult control issues associated with it, substantial gains are accomplished by splitting the diesel injection into two and allocating most of the diesel fuel to the early injection. HCCI/RCCI and PPCI combustion can be used with great effect to reduce the emissions of unburned hydrocarbons at light load. At high load, the challenges that need to be overcome are mostly related to heat. Injector tip temperatures need to be observed since the cooling effect of

  5. Aux marges du monde arabe

    Directory of Open Access Journals (Sweden)

    Hélène Thiollet

    2004-09-01

    Full Text Available L’étude des migrations contemporaines des Érythréens vers le Yémen au tournant des années quatre-vingt-dix permet d’observer les transformations des dynamiques régionales à l’œuvre dans le monde arabe. Les migrations sont un phénomène sensible aux différents aspects (politiques, économiques, culturels, géographiques de l’intégration régionale. Celle si est envisagée dans cet article à travers une approche doublement marginale : -la marginalité géographique de l’Érythrée arabo-africaine et du Yémen, économi­quement isolé dans la péninsule Arabique, -l’étude des migrations formelles et informelles, élément souvent marginal dans l’étude des institutions et des échanges qui constituent un système régional intégré. Cette étude est fondée sur une série d’entretiens menés au Yémen entre février et avril 2002 auprès des administrations yéménites et de la population érythréenne.

  6. A Method of Identification and Inspection for Inventory Control of Irradiated Fuel Elements; Methode d'Identification et d'Inspection Permettant de Proceder a l'Inventaire des Elements Combustibles Irradies; Metod identifikatsii i proverki pri inventarnom kontrole obluchennykh toplivnykh ehlementov; Metodos de Identificacion e Inspeccion para el Control de las Existencias de Elementos Combustibles Irradiados

    Energy Technology Data Exchange (ETDEWEB)

    Kinderman, E. M.; Mills, J. S. [Stanford Research Institute, Menlo Park, CA (United States)

    1966-02-15

    The reactor discharge and irradiated fuel storage locations should be examined in any complete special nuclear materials inventory. They present, however, special physical difficulties to the auditor or inventory control manager. In these locations the distance between object and observer and the poor illumination and optical distortion caused by the shielding media (water, lead glass) contribute to the difficulties of materials inventory. In an attempt to overcome these difficulties and to provide a system for positive identification of reactor discharged fuel, we have developed a compact and convenient optical examination system utilizing a fixed examination station, a periscope, a telescope, and a camera. This system has been tested in a cobalt irradiation pool by examination of test coupons which were marked in various ways, and then treated in a hot, circulating water loop. In the test system, a water-filled periscope, 11-ft long, a catadioptric telescope placed 16 ft from the periscope, and a 35-mm camera for recording the observations were used. The telescope, camera and mountings are all readily portable since they weigh in total less than 22 lb and have maximum dimensions of 29 in. Photographic observations of test resolution charts in air 20 ft away from the object lens of the telescope have demonstrated that the system can resolve markings 22 {mu}m in width. This corresponds to a resolution of 0.8 second of arc. Tests performed on the water system have shown that resolution in this system is better than 50 {mu}m at 20 ft. This corresponds to a resolution of about 1 second of arc. It is clear that the resolution can never be better than the air path system. The present system used in an actual fuel inventory should adequately reproduce any inventory markings. (author) [French] Tout inventaire complet des matieres nucleaires speciales exige un controle au point de dechargement du reacteur et au point de stockage du combustible irradie. Or, ce controle pose

  7. Low Temperature Combustion Demonstrator for High Efficiency Clean Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Ojeda, William de

    2010-07-31

    The project which extended from November 2005 to May of 2010 demonstrated the application of Low Temperature Combustion (LTC) with engine out NOx levels of 0.2 g/bhp-hr throughout the program target load of 12.6bar BMEP. The project showed that the range of loads could be extended to 16.5bar BMEP, therefore matching the reference lug line of the base 2007 MY Navistar 6.4L V8 engine. Results showed that the application of LTC provided a dramatic improvement over engine out emissions when compared to the base engine. Furthermore LTC improved thermal efficiency by over 5% from the base production engine when using the steady state 13 mode composite test as a benchmark. The key enablers included improvements in the air, fuel injection, and cooling systems made in Phases I and II. The outcome was the product of a careful integration of each component under an intelligent control system. The engine hardware provided the conditions to support LTC and the controller provided the necessary robustness for a stable combustion. Phase III provided a detailed account on the injection strategy used to meet the high load requirements. During this phase, the control strategy was implemented in a production automotive grade ECU to perform cycle-by-cycle combustion feedback on each of the engine cylinders. The control interacted on a cycle base with the injection system and with the Turbo-EGR systems according to their respective time constants. The result was a unique system that could, first, help optimize the combustion system and maintain high efficiency, and secondly, extend the steady state results to the transient mode of operation. The engine was upgraded in Phase IV with a Variable Valve Actuation system and a hybrid EGR loop. The impact of the more versatile EGR loop did not provide significant advantages, however the application of VVA proved to be an enabler to further extend the operation of LTC and gain considerable benefits in fuel economy and soot reduction. Finally

  8. Microscale combustion and power generation

    CERN Document Server

    Cadou, Christopher; Ju, Yiguang

    2014-01-01

    Recent advances in microfabrication technologies have enabled the development of entirely new classes of small-scale devices with applications in fields ranging from biomedicine, to wireless communication and computing, to reconnaissance, and to augmentation of human function. In many cases, however, what these devices can actually accomplish is limited by the low energy density of their energy storage and conversion systems. This breakthrough book brings together in one place the information necessary to develop the high energy density combustion-based power sources that will enable many of these devices to realize their full potential. Engineers and scientists working in energy-related fields will find: An overview of the fundamental physics and phenomena of microscale combustion; Presentations of the latest modeling and simulation techniques for gasphase and catalytic micro-reactors; The latest results from experiments in small-scale liquid film, microtube, and porous combustors, micro-thrusters, a...

  9. Combustion process science and technology

    Science.gov (United States)

    Hale, Robert R.

    1989-01-01

    An important and substantial area of technical work in which noncontact temperature measurement (NCTM) is desired is that involving combustion process research. In the planning for this workshop, it was hoped that W. Serignano would provide a briefing regarding the experimental requirements for thermal measurements to support such research. The particular features of thermal measurement requirements included those describing the timeline for combustion experiments, the requirements for thermal control and diagnostics of temperature and other related thermal measurements and the criticality to the involved science to parametric features of measurement capability including precision, repeatability, stability, and resolution. In addition, it was hoped that definitions could be provided which characterize the needs for concurrent imaging as it relates to science observations during the conduct of experimentation.

  10. Dynamical issues in combustion theory

    International Nuclear Information System (INIS)

    Fife, P.C.; Williams, F.

    1991-01-01

    This book looks at the world of combustion phenomena covering the following topics: modeling, which involves the elucidation of the essential features of a given phenomenon through physical insight and knowledge of experimental results, devising appropriate asymptotic and computational methods, and developing sound mathematical theories. Papers in this book describe how all of these challenges have been met for particular examples within a number of common combustion scenarios: reactive shocks, low Mach number premixed reactive flow, nonpremixed phenomena, and solid propellants. The types of phenomena examined are also diverse: the stability and other properties of steady structures, the long time dynamics of evolving solutions, properties of interfaces and shocks, including curvature effects, and spatio-temporal patterns

  11. SPECIFIC EMISSIONS FROM BIOMASS COMBUSTION

    Directory of Open Access Journals (Sweden)

    Pavel Skopec

    2014-02-01

    Full Text Available This paper deals with determining the specific emissions from the combustion of two kinds of biomass fuels in a small-scale boiler. The tested fuels were pellets made of wood and pellets made of rape plant straw. In order to evaluate the specific emissions, several combustion experiments were carried out using a commercial 25 kW pellet-fired boiler. The specific emissions of CO, SO2 and NOx were evaluated in relation to a unit of burned fuel, a unit of calorific value and a unit of produced heat. The specific emissions were compared with some data acquired from the reference literature, with relatively different results. The differences depend mainly on the procedure used for determining the values, and references provide no information about this. Although some of our experimental results may fit with one of the reference sources, they do not fit with the other. The reliability of the references is therefore disputable.

  12. Steady state HNG combustion modeling

    Energy Technology Data Exchange (ETDEWEB)

    Louwers, J.; Gadiot, G.M.H.J.L. [TNO Prins Maurits Lab., Rijswijk (Netherlands); Brewster, M.Q. [Univ. of Illinois, Urbana, IL (United States); Son, S.F. [Los Alamos National Lab., NM (United States); Parr, T.; Hanson-Parr, D. [Naval Air Warfare Center, China Lake, CA (United States)

    1998-04-01

    Two simplified modeling approaches are used to model the combustion of Hydrazinium Nitroformate (HNF, N{sub 2}H{sub 5}-C(NO{sub 2}){sub 3}). The condensed phase is treated by high activation energy asymptotics. The gas phase is treated by two limit cases: the classical high activation energy, and the recently introduced low activation energy approach. This results in simplification of the gas phase energy equation, making an (approximate) analytical solution possible. The results of both models are compared with experimental results of HNF combustion. It is shown that the low activation energy approach yields better agreement with experimental observations (e.g. regression rate and temperature sensitivity), than the high activation energy approach.

  13. Oxy-coal Combustion Studies

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, J. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Lighty, J. [Univ. of Utah, Salt Lake City, UT (United States); Ring, T. [Univ. of Utah, Salt Lake City, UT (United States); Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Thornock, J. [Univ. of Utah, Salt Lake City, UT (United States); Y Jia, W. Morris [Univ. of Utah, Salt Lake City, UT (United States); Pedel, J. [Univ. of Utah, Salt Lake City, UT (United States); Rezeai, D. [Univ. of Utah, Salt Lake City, UT (United States); Wang, L. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, J. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States)

    2012-01-06

    The objective of this project is to move toward the development of a predictive capability with quantified uncertainty bounds for pilot-scale, single-burner, oxy-coal operation. This validation research brings together multi-scale experimental measurements and computer simulations. The combination of simulation development and validation experiments is designed to lead to predictive tools for the performance of existing air fired pulverized coal boilers that have been retrofitted to various oxy-firing configurations. In addition, this report also describes novel research results related to oxy-combustion in circulating fluidized beds. For pulverized coal combustion configurations, particular attention is focused on the effect of oxy-firing on ignition and coal-flame stability, and on the subsequent partitioning mechanisms of the ash aerosol.

  14. Enhanced Combustion Low NOx Pulverized Coal Burner

    Energy Technology Data Exchange (ETDEWEB)

    David Towle; Richard Donais; Todd Hellewell; Robert Lewis; Robert Schrecengost

    2007-06-30

    economic evaluation and commercial application. During the project performance period, Alstom performed computational fluid dynamics (CFD) modeling and large pilot scale combustion testing in its Industrial Scale Burner Facility (ISBF) at its U.S. Power Plant Laboratories facility in Windsor, Connecticut in support of these objectives. The NOx reduction approach was to optimize near-field combustion to ensure that minimum NOx emissions are achieved with minimal impact on unburned carbon in ash, slagging and fouling, corrosion, and flame stability/turn-down. Several iterations of CFD and combustion testing on a Midwest coal led to an optimized design, which was extensively combustion tested on a range of coals. The data from these tests were then used to validate system costs and benefits versus SCR. Three coals were evaluated during the bench-scale and large pilot-scale testing tasks. The three coals ranged from a very reactive subbituminous coal to a moderately reactive Western bituminous coal to a much less reactive Midwest bituminous coal. Bench-scale testing was comprised of standard ASTM properties evaluation, plus more detailed characterization of fuel properties through drop tube furnace testing and thermogravimetric analysis. Bench-scale characterization of the three test coals showed that both NOx emissions and combustion performance are a strong function of coal properties. The more reactive coals evolved more of their fuel bound nitrogen in the substoichiometric main burner zone than less reactive coal, resulting in the potential for lower NOx emissions. From a combustion point of view, the more reactive coals also showed lower carbon in ash and CO values than the less reactive coal at any given main burner zone stoichiometry. According to bench-scale results, the subbituminous coal was found to be the most amenable to both low NOx, and acceptably low combustibles in the flue gas, in an air staged low NOx system. The Midwest bituminous coal, by contrast, was

  15. Coal combustion technology in China

    International Nuclear Information System (INIS)

    Huang, Z.X.

    1994-01-01

    Coal is the most important energy source in China, the environmental pollution problem derived from coal burning is rather serious in China. The present author discusses coal burning technologies both in boilers and industrial furnaces and their relations with environmental protection problems in China. The technological situations of Circulating Fluidized Bed Coal Combustor, Pulverized Coal Combustor with Aerodynamic Flame Holder and Coal Water Slurry Combustion have been discussed here as some of the interesting problems in China only. (author). 3 refs

  16. Example Problems in LES Combustion

    Science.gov (United States)

    2016-09-26

    Lesieur, M., Turbulence in Fluids , 2nd Revised Ed., Fluid Mechanics and Its Applications, Vol. 1, Kluwer Academic Publishers, Boston, Massachusetts, 1990...34, Journal of Fluid Mechanics , Vol. 238, 1992, pp. 155-185. 5. Hirsch, C., Numerical Computation of Internal and External Flows, Vol. 2, Computational...reaction mechanisms for the oxidation of hydrocarbon fuels in flames", Combustion Science and Technology, Vol. 27, 1981, pp. 31-43. 14. Spalding, D.B

  17. Cirque du Monde as a health intervention

    Science.gov (United States)

    Fournier, Cynthia; Drouin, Mélodie-Anne; Marcoux, Jérémie; Garel, Patricia; Bochud, Emmanuel; Théberge, Julie; Aubertin, Patrice; Favreau, Gil; Fleet, Richard

    2014-01-01

    Abstract Objective To present Cirque du Soleil’s social circus program, Cirque du Monde, to explore its potential as a primary health care tool for family physicians. Data sources A review of the literature in PubMed, the Cochrane Library, PsycINFO, LaPresse, Eureka, Google Scholar, and Érudit using the key words circus, social circus, Cirque du Monde, and Cirque du Soleil; a Montreal-based initiative, Espace Transition, modeled on Cirque du Monde; and personal communication with Cirque du Soleil’s Social Circus Training Advisor. Study selection The first 50 articles or websites identified for each key word in each of the databases were examined on the basis of their titles and abstracts in the case of articles, and on the basis of their titles and page content in the case of websites. Articles and websites that explored an aspect of social circuses or that described an intervention that involved circuses were then retained for analysis. Because all literature on social circuses was searched, no criterion for year of publication was used. Synthesis No articles on the social circus as a health intervention were found. One study on the use of the circus as an intervention in schools was identified. It demonstrated an increase in self-esteem in the children who took part. One study on the use of the circus in a First Nations community was found; it contained nonspecific, qualitative findings. The other articles identified were merely descriptions of social circuses. One website was identified on the use of the social circus to help youth who had been treated in a hospital setting for major psychiatric disorders to re-enter the community. The team in the pediatric psychiatry department at Centre Hospitalier Universitaire Sainte-Justine, the children’s hospital in Montreal, Que, was contacted; they were leading this project, called Espace Transition. The unpublished preliminary findings of its pilot project demonstrate substantial improvements in overall patient

  18. Combustion instability modeling and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Santoro, R.J.; Yang, V.; Santavicca, D.A. [Pennsylvania State Univ., University Park, PA (United States)] [and others

    1995-10-01

    It is well known that the two key elements for achieving low emissions and high performance in a gas turbine combustor are to simultaneously establish (1) a lean combustion zone for maintaining low NO{sub x} emissions and (2) rapid mixing for good ignition and flame stability. However, these requirements, when coupled with the short combustor lengths used to limit the residence time for NO formation typical of advanced gas turbine combustors, can lead to problems regarding unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions, as well as the occurrence of combustion instabilities. Clearly, the key to successful gas turbine development is based on understanding the effects of geometry and operating conditions on combustion instability, emissions (including UHC, CO and NO{sub x}) and performance. The concurrent development of suitable analytical and numerical models that are validated with experimental studies is important for achieving this objective. A major benefit of the present research will be to provide for the first time an experimentally verified model of emissions and performance of gas turbine combustors.

  19. Combustion char characterisation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, P; Ingermann Petersen, H; Sund Soerensen, H; Thomsen, E; Guvad, C

    1996-06-01

    The aim was to correlate reactivity measures of raw coals and the maceral concentrates of the coals obtained in a previous project with the morphology of the produced chars by using a wire grid devolatilization method. Work involved determination of morphology, macroporosity and a detailed study by Scanning Electron Microscopy (SEM). Systematic variations in the texture of chars produced in different temperature domains and heating rates were demonstrated by using incident light microscopy on polished blocks and by SEM studies directly on the surfaces of untreated particles. Results suggest that work in the field of char reactivity estimates and correlations between char morphology and coal petrography can be accomplished only on chars produced under heating rates and temperatures comparable to those for the intended use of coal. A general correlation between the coals` petrography and the the morphology of high temperature chars was found. The SEM study of the chars revealed that during the devolatilization period the particles fuse and the macroporosity and thus the morphotypes are formed. After devolatilization ceases, secondary micropores are formed. These develop in number and size throughout the medium combustion interval. At the end of the combustion interval the macrostructure breaks down, caused by coalescence of the increased number of microspores. This can be observed as a change in the morphology and the macroporosity of the chars. Results indicate that char reactivity is a function of the macroporosity and thus the morphology of combustion chars. (AB) 34 refs.

  20. Management of coal combustion wastes

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-02-01

    It has been estimated that 780 Mt of coal combustion products (CCPs) were produced worldwide in 2010. Only about 53.5% were utilised, the rest went to storage or disposal sites. Disposal of coal combustion waste (CCW) on-site at a power plant may involve decades-long accumulation of waste, with hundreds of thousands, if not millions, of tonnes of dry ash or wet ash slurry being stored. In December 2008, a coal combustion waste pond in Kingston, Tennessee, USA burst. Over 4 million cubic metres of ash sludge poured out, burying houses and rivers in tonnes of toxic waste. Clean-up is expected to continue into 2014 and will cost $1.2 billion. The incident drew worldwide attention to the risk of CCW disposal. This caused a number of countries to review CCW management methods and regulations. The report begins by outlining the physical and chemical characteristics of the different type of ashes generated in a coal-fired power plant. The amounts of CCPs produced and regulations on CCW management in selected countries have been compiled. The CCW disposal methods are then discussed. Finally, the potential environmental impacts and human health risks of CCW disposal, together with the methods used to prevent them, are reviewed.