The impact of dry matter loss during herbaceous biomass storage on net greenhouse gas emissions from biofuels production

International Nuclear Information System (INIS)

Emery, Isaac R.; Mosier, Nathan S.

2012-01-01

Life cycle inventory models of greenhouse gas emissions from biofuel production have become tightly integrated into government mandates and other policies to encourage biofuel production. Current models do not include life cycle impacts of biomass storage or reflect current literature on emissions from soil and biomass decomposition. In this study, the GREET model framework was used to determine net greenhouse gas emissions during ethanol production from corn and switchgrass via three biomass storage systems: wet ensiling of whole corn, and indoor and outdoor dry bale storage of corn stover and switchgrass. Dry matter losses during storage were estimated from the literature and used to modify GREET inventory analysis. Results showed that biomass stability is a key parameter affecting fuel production per farmed hectare and life cycle greenhouse gas emissions. Corn silage may generate 5358 L/ha of ethanol at 26.5 g CO 2 eq/MJ, relative to 5654 L/ha at 52.3 g CO 2 eq/MJ from combined corn stover and conventional grain corn ethanol production, or 3919 L/ha at 21.3 g CO 2 eq/MJ from switchgrass. Dry matter losses can increase net emissions by 3–25% (ensiling), 5–53% (bales outdoors), or 1–12% (bales indoors), decreasing the net GHG reduction of ethanol over gasoline by up to 10.9%. Greater understanding of biomass storage losses and greenhouse gas fluxes during storage is necessary to accurately assess biomass storage options to ensure that the design of biomass supply logistics systems meet GHG reduction mandates for biofuel production. -- Highlights: ► Analyzed the impact of biomass loss during storage. ► Probable dry matter losses strongly depend on storage method and infrastructure. ► Assessed impact of storage losses on LCA for cellulosic ethanol production. ► Storage losses increase GHG emissions by 1–53% depending upon storage conditions.

BioDry: An Inexpensive, Low-Power Method to Preserve Aquatic Microbial Biomass at Room Temperature.

Science.gov (United States)

Tuorto, Steven J; Brown, Chris M; Bidle, Kay D; McGuinness, Lora R; Kerkhof, Lee J

2015-01-01

This report describes BioDry (patent pending), a method for reliably preserving the biomolecules associated with aquatic microbial biomass samples, without the need of hazardous materials (e.g. liquid nitrogen, preservatives, etc.), freezing, or bulky storage/sampling equipment. Gel electrophoresis analysis of nucleic acid extracts from samples treated in the lab with the BioDry method indicated that molecular integrity was protected in samples stored at room temperature for up to 30 days. Analysis of 16S/18S rRNA genes for presence/absence and relative abundance of microorganisms using both 454-pyrosequencing and TRFLP profiling revealed statistically indistinguishable communities from control samples that were frozen in liquid nitrogen immediately after collection. Seawater and river water biomass samples collected with a portable BioDry "field unit", constructed from off-the-shelf materials and a battery-operated pumping system, also displayed high levels of community rRNA preservation, despite a slight decrease in nucleic acid recovery over the course of storage for 30 days. Functional mRNA and protein pools from the field samples were also effectively conserved with BioDry, as assessed by respective RT-PCR amplification and western blot of ribulose-1-5-bisphosphate carboxylase/oxygenase. Collectively, these results demonstrate that BioDry can adequately preserve a suite of biomolecules from aquatic biomass at ambient temperatures for up to a month, giving it great potential for high resolution sampling in remote locations or on autonomous platforms where space and power are limited.

BioDry: An Inexpensive, Low-Power Method to Preserve Aquatic Microbial Biomass at Room Temperature.

Directory of Open Access Journals (Sweden)

Steven J Tuorto

Full Text Available This report describes BioDry (patent pending, a method for reliably preserving the biomolecules associated with aquatic microbial biomass samples, without the need of hazardous materials (e.g. liquid nitrogen, preservatives, etc., freezing, or bulky storage/sampling equipment. Gel electrophoresis analysis of nucleic acid extracts from samples treated in the lab with the BioDry method indicated that molecular integrity was protected in samples stored at room temperature for up to 30 days. Analysis of 16S/18S rRNA genes for presence/absence and relative abundance of microorganisms using both 454-pyrosequencing and TRFLP profiling revealed statistically indistinguishable communities from control samples that were frozen in liquid nitrogen immediately after collection. Seawater and river water biomass samples collected with a portable BioDry "field unit", constructed from off-the-shelf materials and a battery-operated pumping system, also displayed high levels of community rRNA preservation, despite a slight decrease in nucleic acid recovery over the course of storage for 30 days. Functional mRNA and protein pools from the field samples were also effectively conserved with BioDry, as assessed by respective RT-PCR amplification and western blot of ribulose-1-5-bisphosphate carboxylase/oxygenase. Collectively, these results demonstrate that BioDry can adequately preserve a suite of biomolecules from aquatic biomass at ambient temperatures for up to a month, giving it great potential for high resolution sampling in remote locations or on autonomous platforms where space and power are limited.

Transpirational drying and costs for transporting woody biomass - a preliminary review

Science.gov (United States)

Bryce J. Stokes; Bryce J. McDonaStokes; Timothy P. McDonald; Tyrone Kelley

1993-01-01

High transport costs arc a factor to consider in the use of forest residues for fuel. Costs can be reduced by increasing haul capacities, reducing high moisture contents, and improving trucking efficiency. The literature for transpirational drying and the economics of hauling woody biomass is summarized here. Some additional, unpublished roundwood and chipdrying test...

Effect of biomass concentration on methane oxidation activity using mature compost and graphite granules as substrata.

Science.gov (United States)

Xie, S; O'Dwyer, T; Freguia, S; Pikaar, I; Clarke, W P

2016-10-01

Reported methane oxidation activity (MOA) varies widely for common landfill cover materials. Variation is expected due to differences in surface area, the composition of the substratum and culturing conditions. MOA per methanotrophic cell has been calculated in the study of natural systems such as lake sediments to examine the inherent conditions for methanotrophic activity. In this study, biomass normalised MOA (i.e., MOA per methanotophic cell) was measured on stabilised compost, a commonly used cover in landfills, and on graphite granules, an inert substratum widely used in microbial electrosynthesis studies. After initially enriching methanotrophs on both substrata, biomass normalised MOA was quantified under excess oxygen and limiting methane conditions in 160ml serum vials on both substrata and blends of the substrata. Biomass concentration was measured using the bicinchoninic acid assay for microbial protein. The biomass normalised MOA was consistent across all compost-to-graphite granules blends, but varied with time, reflecting the growth phase of the microorganisms. The biomass normalised MOA ranged from 0.069±0.006μmol CH4/mg dry biomass/h during active growth, to 0.024±0.001μmol CH4/mg dry biomass/h for established biofilms regardless of the substrata employed, indicating the substrata were equally effective in terms of inherent composition. The correlation of MOA with biomass is consistent with studies on methanotrophic activity in natural systems, but biomass normalised MOA varies by over 5 orders of magnitude between studies. This is partially due to different methods being used to quantify biomass, such as pmoA gene quantification and the culture dependent Most Probable Number method, but also indicates that long term exposure of materials to a supply of methane in an aerobic environment, as can occur in natural systems, leads to the enrichment and adaptation of types suitable for those conditions. Copyright © 2016 Elsevier Ltd. All rights

Biomass gasification for CHP with dry gas cleaning and regenerative heat recovery

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

Small scale CHP plants based on biomass gasification technologies are generally expensive and not very efficient due to gas quality problems which increase operation and maintenance cost as well as breakdown. To overcome this situation the team has developed, integrated and tested a complete biomass gasification combine heat and power prototype plant of 250 kWth equipped with a specifically developed dry gas cleaning and heat recovery system. The dry gas cleaning device is a simple dry gas regenerative heat exchanger where tars are stopped by condensation but working at a temperature above due point in order to avoid water condensation. Two types of heat particles separation devices have been tested in parallel multi-cyclone and ceramic filters. After several month spent on modelling design, construction and optimisation, a full test campaign of 400 hours continuous monitoring has been done where all working parameters has been monitored and gas cleaning device performances has been assessed. Results have shown: Inappropriateness of the ceramic filters for the small scale unit due to operation cost and too high sensibility of the filters to the operation conditions fluctuating in a wide range, despite a very high particle separation efficiency 99 %; Rather good efficiency of the multi-cyclone 72% but not sufficient for engine safety. Additional conventional filters where necessary for the finest part; Inappropriateness of the dry gas heat exchanger device for tar removal partly due to a low tar content of the syngas generated, below 100 mg/Nm{sup 3} , but also due to their composition which would have imposed, to be really efficient, a theoretical condensing temperature of 89 C below the water condensation temperature. These results have been confirmed by laboratory tests and modelling. However the tar cracking phase have shown very interesting results and proved the feasibility of thermal cracking with full cleaning of the heat exchanger without further mechanical

Volume and aboveground biomass models for dry Miombo woodland in Tanzania

DEFF Research Database (Denmark)

Mwakalukwa, Ezekiel Edward; Meilby, Henrik; Treue, Thorsten

2014-01-01

Tools to accurately estimate tree volume and biomass are scarce for most forest types in East Africa, including Tanzania. Based on a sample of 142 trees and 57 shrubs from a 6,065 ha area of dry miombo woodland in Iringa rural district in Tanzania, regression models were developed for volume...... and biomass of three important species, Brachystegia spiciformis Benth. (n=40), Combretum molle G. Don (n=41), and Dalbergia arbutifolia Baker (n=37) separately, and for broader samples of trees (28 species, n=72), shrubs (16 species, n=31), and trees and shrubs combined (44 species, n=104). Applied...... of the predictions tended to increase from general to species-specific models. Except for a few volume and biomass models developed for shrubs, all models had R2 values of 96–99%. Thus, the models appear robust and should be applicable to forests with similar site conditions, species, and diameter ranges....

Eco-friendly dry chemo-mechanical pretreatments of lignocellulosic biomass: Impact on energy and yield of the enzymatic hydrolysis

International Nuclear Information System (INIS)

Barakat, Abdellatif; Chuetor, Santi; Monlau, Florian; Solhy, Abderrahim; Rouau, Xavier

2014-01-01

Highlights: • Innovative dry NaOH chemo-mechanical pretreatment was developed. • Dry (TS dry ) and dilute (TS dilute ) NaOH chemo-mechanical pretreatment were compared. • TS dilute consumed higher amounts of water and energy compared to TS dry . • Energy efficiency obtained for TS dilute was 0.417 kg glucose kW h −1 and 0.888 for TS dry . - Abstract: In this study, we developed an eco-friendly dry alkaline chemomechanical pretreatment of wheat straw without production of waste and liquid fractions with objective to save energy input, to decrease the environmental impact and to increase enzymatic hydrolysis. Wheat straw was pretreated with NH 3 , NaOH-H 2 O 2 , NH 3 -H 2 O 2 and NaOH at high materials concentration (5 kg/L) equivalent to biomass/liquid ratio of 1/5 (dry chemomechanical) and at low materials concentration (0.2 kg/L) equivalent to biomass/liquid ratio of 5/1 (dilute chemomechanical). Untreated and chemical treated wheat straw samples were subjected to grinding and milling following by enzymatic hydrolysis with commercial cellulases. NaOH and NaOH-H 2 O 2 dry chemomechanical pretreatments were found to be more effective in decreasing the particle size and energy consumption and increasing the surface area. However, alkaline dilute-chemomechanical treatments consumed higher amounts of water (5 L water/1 kg biomass) and energy compared to dry-chemomechanical treatments. In point of fact, the lowest energy efficiency obtained was 0.417 kg glucose kW h −1 for dilute-chemomechanical treatments compared to 0.888 kg glucose kW h −1 glucose kW h −1 for dry-chemomechanical treatments. Alkaline dry-chemomechanical pretreatments approach appears more attractive and efficient in terms of glucose, energy efficiency and environmental impact, compared to conventional alkaline chemomechanical pretreatments

Biomass burning emissions in north Australia during the early dry season: an overview of the 2014 SAFIRED campaign

Directory of Open Access Journals (Sweden)

M. D. Mallet

2017-11-01

Full Text Available The SAFIRED (Savannah Fires in the Early Dry Season campaign took place from 29 May until 30 June 2014 at the Australian Tropical Atmospheric Research Station (ATARS in the Northern Territory, Australia. The purpose of this campaign was to investigate emissions from fires in the early dry season in northern Australia. Measurements were made of biomass burning aerosols, volatile organic compounds, polycyclic aromatic carbons, greenhouse gases, radon, speciated atmospheric mercury and trace metals. Aspects of the biomass burning aerosol emissions investigated included; emission factors of various species, physical and chemical aerosol properties, aerosol aging, micronutrient supply to the ocean, nucleation, and aerosol water uptake. Over the course of the month-long campaign, biomass burning signals were prevalent and emissions from several large single burning events were observed at ATARS.Biomass burning emissions dominated the gas and aerosol concentrations in this region. Dry season fires are extremely frequent and widespread across the northern region of Australia, which suggests that the measured aerosol and gaseous emissions at ATARS are likely representative of signals across the entire region of north Australia. Air mass forward trajectories show that these biomass burning emissions are carried north-west over the Timor Sea and could influence the atmosphere over Indonesia and the tropical atmosphere over the Indian Ocean. Here we present characteristics of the biomass burning observed at the sampling site and provide an overview of the more specific outcomes of the SAFIRED campaign.

Biomass burning emissions in north Australia during the early dry season: an overview of the 2014 SAFIRED campaign

Science.gov (United States)

Mallet, Marc D.; Desservettaz, Maximilien J.; Miljevic, Branka; Milic, Andelija; Ristovski, Zoran D.; Alroe, Joel; Cravigan, Luke T.; Rohan Jayaratne, E.; Paton-Walsh, Clare; Griffith, David W. T.; Wilson, Stephen R.; Kettlewell, Graham; van der Schoot, Marcel V.; Selleck, Paul; Reisen, Fabienne; Lawson, Sarah J.; Ward, Jason; Harnwell, James; Cheng, Min; Gillett, Rob W.; Molloy, Suzie B.; Howard, Dean; Nelson, Peter F.; Morrison, Anthony L.; Edwards, Grant C.; Williams, Alastair G.; Chambers, Scott D.; Werczynski, Sylvester; Williams, Leah R.; Winton, V. Holly L.; Atkinson, Brad; Wang, Xianyu; Keywood, Melita D.

2017-11-01

The SAFIRED (Savannah Fires in the Early Dry Season) campaign took place from 29 May until 30 June 2014 at the Australian Tropical Atmospheric Research Station (ATARS) in the Northern Territory, Australia. The purpose of this campaign was to investigate emissions from fires in the early dry season in northern Australia. Measurements were made of biomass burning aerosols, volatile organic compounds, polycyclic aromatic carbons, greenhouse gases, radon, speciated atmospheric mercury and trace metals. Aspects of the biomass burning aerosol emissions investigated included; emission factors of various species, physical and chemical aerosol properties, aerosol aging, micronutrient supply to the ocean, nucleation, and aerosol water uptake. Over the course of the month-long campaign, biomass burning signals were prevalent and emissions from several large single burning events were observed at ATARS.Biomass burning emissions dominated the gas and aerosol concentrations in this region. Dry season fires are extremely frequent and widespread across the northern region of Australia, which suggests that the measured aerosol and gaseous emissions at ATARS are likely representative of signals across the entire region of north Australia. Air mass forward trajectories show that these biomass burning emissions are carried north-west over the Timor Sea and could influence the atmosphere over Indonesia and the tropical atmosphere over the Indian Ocean. Here we present characteristics of the biomass burning observed at the sampling site and provide an overview of the more specific outcomes of the SAFIRED campaign.

In-depth investigation on the pyrolysis kinetics of raw biomass. Part I: kinetic analysis for the drying and devolatilization stages.

Science.gov (United States)

Chen, Dengyu; Zheng, Yan; Zhu, Xifeng

2013-03-01

An in-depth investigation was conducted on the kinetic analysis of raw biomass using thermogravimetric analysis (TGA), from which the activation energy distribution of the whole pyrolysis process was obtained. Two different stages, namely, drying stage (Stage I) and devolatilization stage (Stage II), were shown in the pyrolysis process in which the activation energy values changed with conversion. The activation energy at low conversions (below 0.15) in the drying stage ranged from 10 to 30 kJ/mol. Such energy was calculated using the nonisothermal Page model, known as the best model to describe the drying kinetics. Kinetic analysis was performed using the distributed activation energy model in a wide range of conversions (0.15-0.95) in the devolatilization stage. The activation energy first ranged from 178.23 to 245.58 kJ/mol and from 159.66 to 210.76 kJ/mol for corn straw and wheat straw, respectively, then increasing remarkably with an irregular trend. Copyright © 2012 Elsevier Ltd. All rights reserved.

Activated carbon from biomass

Science.gov (United States)

Manocha, S.; Manocha, L. M.; Joshi, Parth; Patel, Bhavesh; Dangi, Gaurav; Verma, Narendra

2013-06-01

Activated carbon are unique and versatile adsorbents having extended surface area, micro porous structure, universal adsorption effect, high adsorption capacity and high degree of surface reactivity. Activated carbons are synthesized from variety of materials. Most commonly used on a commercial scale are cellulosic based precursors such as peat, coal, lignite wood and coconut shell. Variation occurs in precursors in terms of structure and carbon content. Coir having very low bulk density and porous structure is found to be one of the valuable raw materials for the production of highly porous activated carbon and other important factor is its high carbon content. Exploration of good low cost and non conventional adsorbent may contribute to the sustainability of the environment and offer promising benefits for the commercial purpose in future. Carbonization of biomass was carried out in a horizontal muffle furnace. Both carbonization and activation were performed in inert nitrogen atmosphere in one step to enhance the surface area and to develop interconnecting porosity. The types of biomass as well as the activation conditions determine the properties and the yield of activated carbon. Activated carbon produced from biomass is cost effective as it is easily available as a waste biomass. Activated carbon produced by combination of chemical and physical activation has higher surface area of 2442 m2/gm compared to that produced by physical activation (1365 m2/gm).

Conversion Efficiency of Photosynthetically Active Radiation Into Acacia mearnsii Biomass

Directory of Open Access Journals (Sweden)

Elder Eloy

2018-02-01

Full Text Available ABSTRACT The objective of this experiment was to determine the conversion efficiency of intercepted photosynthetically active radiation into biomass of Acacia mearnsii De Wild. seedlings. A forest species, plastic tubes (90 cm3, and 11 evaluation periods (up to 180 days after emergence were used in this study. The leaf area index (LAI, total dry biomass (BIO, global solar radiation (GSR, cumulative intercepted photosynthetically active radiation (PARic, and conversion efficiency of radiation (εb were determined using a pyranometer (LI200X, LICOR. The value of εb in BIO seedlings of Acacia mearnsii was 7.76 g MJ-1. LAI was directly related to the efficiency of PARic, and this influenced the development, production potential and accumulation of BIO. The value of GSR flow was 11.81 MJ m-2 day-1, while the value inside the greenhouse was 6.26 MJ m-2 day-1.

Comparative study of wet and dry torrefaction of corn stalk and the effect on biomass pyrolysis polygeneration.

Science.gov (United States)

Wang, Xianhua; Wu, Jing; Chen, Yingquan; Pattiya, Adisak; Yang, Haiping; Chen, Hanping

2018-06-01

Wet torrefaction (WT) possesses some advantages over dry torrefaction (DT). In this study, a comparative analysis of torrefied corn stalk from WT and DT was conducted along with an investigation of their pyrolysis properties under optimal conditions for biomass pyrolysis polygeneration. Compared with DT, WT removed 98% of the ash and retained twice the amount of hydrogen. The impacts of DT and WT on the biomass macromolecular structure was also found to be different using two-dimensional perturbation correlation infrared spectroscopy (2D-PCIS). WT preserved the active hydroxyl groups and rearranged the macromolecule structure to allow cellulose to be more ordered, while DT removed these active hydroxyl groups and formed inter-crosslinking structures in macromolecules. Correspondingly, the bio-char yield after WT was lower than DT but the bio-char quality was upgraded due to high ash removal. Furthermore, higher bio-oil yield, higher sugar content, and higher H 2 generation, were obtained after WT. Copyright © 2018 Elsevier Ltd. All rights reserved.

Biomass and nutrient dynamics associated with slash fires in neotropical dry forests

International Nuclear Information System (INIS)

Kauffman, J.B.; Cummings, D.L.; Sanford, R.L. Jr.; Salcedo, I.H.; Sampaio, E.V.S.B.

1993-01-01

Unprecedented rates of deforestation and biomass burning in tropical dry forests are dramatically influencing biogeochemical cycles, resulting in resource depletion, declines in biodiversity, and atmospheric pollution. We quantified the effects of deforestation and varying levels of slash-fire severity on nutrient losses and redistribution in a second-growth tropical dry forest (open-quotes Caatingaclose quotes) near Serra Talhada, Pernambuco, Brazil. Total aboveground biomass prior to burning was ∼74 Mg/ha. Nitrogen and phosphorus concentrations were highest in litter, leaves attached to slash, and fine wood debris (< O.64 cm diameter). While these components comprised only 30% of the prefire aboveground biomass, they accounted for ∼60% of the aboveground pools of N and P. Three experimental fires were conducted during the 1989 burning season. Consumption was 78, 88, and 95% of the total aboveground biomass. As much as 96% of the prefire aboveground N and C pools and 56% of the prefire aboveground P pool was lost. Nitrogen losses exceeded 500 kg/ha and P losses exceeded 20 kg/ha in the fires of the greatest severity. With increasing fire severity, the concentrations of N and P in ash decreased while the concentration of Ca increased. Greater ecosystem losses of these nutrients occurred with increasing fire severity. Following fire, up to 47% of the residual aboveground N and 84% of the residual aboveground P were in the form of ash, quickly lost from the site via wind erosion. Fires appeared to have a minor immediate effect on total N, C, or P in the soils. However, soils in forests with no history of cultivation had significantly higher concentrations of C and P than second-growth forests. It would likely require a century or more of fallow for reaccumulation to occur. However, current fallow periods in this region are 15 yr or less. 38 refs., 2 figs., 7 tabs

Development of equations for predicting Puerto Rican subtropical dry forest biomass and volume

Science.gov (United States)

Thomas J. Brandeis; Matthew Delaney; Bernard R. Parresol; Larry Royer

2006-01-01

Carbon accounting, forest health monitoring and sustainable management of the subtropical dry forests of Puerto Rico and other Caribbean Islands require an accurate assessment of forest aboveground biomass (AGB) and stem volume. One means of improving assessment accuracy is the development of predictive equations derived from locally collected data. Forest inventory...

Effect of operational factors on bioregeneration of binary phenol and 4-chlorophenol-loaded granular activated carbon using PVA-immobilized biomass cryogels.

Science.gov (United States)

Leong, Kwok-Yii; Adnan, Rohana; Lim, Poh-Eng; Ng, Si-Ling; Seng, Chye-Eng

2017-09-01

The effects of dry biomass density in cryogel beads, shaking speed and initial concentration ratio of phenol to 4-chlorophenol (4-CP) on the bioregeneration efficiencies of binary phenol and 4-CP-loaded granular activated carbon (GAC) for phenol and 4-CP, respectively, were investigated under the simultaneous adsorption and biodegradation approach. The results revealed higher bioregeneration efficiencies of binary-loaded GAC for phenol and 4-CP at higher dry biomass density but moderate shaking speed. The optimum dry biomass density in cryogel beads and shaking speed for use in bioregeneration were found to be 0.01 g/mL and 250 rpm, respectively. With respect to the initial phenol to 4-CP concentration ratio, the bioregeneration efficiencies were lower under increasing phenol and 4-CP initial concentrations, respectively, with the effect being more conspicuous under increasing 4-CP concentration. Higher bioregeneration efficiencies were achieved with the use of immobilized rather than suspended biomasses.

Impact of Precipitation Patterns on Biomass and Species Richness of Annuals in a Dry Steppe

Science.gov (United States)

Yan, Hong; Liang, Cunzhu; Li, Zhiyong; Liu, Zhongling; Miao, Bailing; He, Chunguang; Sheng, Lianxi

2015-01-01

Annuals are an important component part of plant communities in arid and semiarid grassland ecosystems. Although it is well known that precipitation has a significant impact on productivity and species richness of community or perennials, nevertheless, due to lack of measurements, especially long-term experiment data, there is little information on how quantity and patterns of precipitation affect similar attributes of annuals. This study addresses this knowledge gap by analyzing how quantity and temporal patterns of precipitation affect aboveground biomass, interannual variation aboveground biomass, relative aboveground biomass, and species richness of annuals using a 29-year dataset from a dry steppe site at the Inner Mongolia Grassland Ecosystem Research Station. Results showed that aboveground biomass and relative aboveground biomass of annuals increased with increasing precipitation. The coefficient of variation in aboveground biomass of annuals decreased significantly with increasing annual and growing-season precipitation. Species richness of annuals increased significantly with increasing annual precipitation and growing-season precipitation. Overall, this study highlights the importance of precipitation for aboveground biomass and species richness of annuals. PMID:25906187

Co-combustion of low rank coal/waste biomass blends using dry air or oxygen

International Nuclear Information System (INIS)

Haykiri-Acma, H.; Yaman, S.; Kucukbayrak, S.

2013-01-01

Biomass species such as the rice husk and the olive milling residue, and a low quality Turkish coal, Soma Denis lignite, were burned in a thermal analyzer under pure oxygen and dry air up to 900 °C, and differential thermal analysis (DTA) and derivative thermogravimetric (DTG) analysis profiles were obtained. Co-combustion experiments of lignite/biomass blends containing 5–20 wt% of biomass were also performed. The effects of the oxidizer type and the blending ratio of biomass were evaluated considering some thermal reactivity indicators such as the maximum burning rate and its temperature, the maximum heat flow temperature, and the burnout levels. FTIR (Fourier transform infrared) spectroscopy and SEM (scanning electron microscopy) were used to characterize the samples, and the variations in the combustion characteristics of the samples were interpreted based on the differences in the intrinsic properties of the samples. - Highlights: ► Co-combustion of lignite/biomass blends. ► The effects of the oxidizer type and the blending ratio. ► Effects of intrinsic properties on combustion characteristics.

Intercropping Between Achillea millefolium L. and Rosmarinus officinalis L. and its effects on essential oil yield, biomass and anti-microbial activity

OpenAIRE

Arashiro, Munique Polito; Centro Universitário de Maringá - CESUMAR; Ziroldo, Débora Fernanda; Centro Universitário de Maringá - CESUMAR; Yamaguchi, Mirian Ueda; Centro Universitário de Maringá - CESUMAR; Sartor, Claudenice Francisca Providelo; Centro Universitário de Maringá - CESUMAR; Patroni, Sandra Sanches; Centro Universitário de Maringá - CESUMAR; Oliveira, Pérsio Sandir D'; EMBRAPA; Cortez, Lúcia Elaine Elaine Ranieri; Centro Universitário de Maringá - CESUMAR

2011-01-01

The rosemary (Rosmarinus officinalis) and the yarrow (Achillea millefolium) are medicinal aromatic herbs and produce essential oil. Current experiment evaluated the effect of intercropping between two species in biomass and essential oil yield and the antimicrobial activity of the essential oil of rosemary. After the plants’ culture and harvest, the biomass and the essential oil yields of the dry leaves and flowers were obtained by steam water distillation. Data of biomass and essential oil y...

Flow Cytometry Pulse Width Data Enables Rapid and Sensitive Estimation of Biomass Dry Weight in the Microalgae Chlamydomonas reinhardtii and Chlorella vulgaris

Science.gov (United States)

Chioccioli, Maurizio; Hankamer, Ben; Ross, Ian L.

2014-01-01

Dry weight biomass is an important parameter in algaculture. Direct measurement requires weighing milligram quantities of dried biomass, which is problematic for small volume systems containing few cells, such as laboratory studies and high throughput assays in microwell plates. In these cases indirect methods must be used, inducing measurement artefacts which vary in severity with the cell type and conditions employed. Here, we utilise flow cytometry pulse width data for the estimation of cell density and biomass, using Chlorella vulgaris and Chlamydomonas reinhardtii as model algae and compare it to optical density methods. Measurement of cell concentration by flow cytometry was shown to be more sensitive than optical density at 750 nm (OD750) for monitoring culture growth. However, neither cell concentration nor optical density correlates well to biomass when growth conditions vary. Compared to the growth of C. vulgaris in TAP (tris-acetate-phosphate) medium, cells grown in TAP + glucose displayed a slowed cell division rate and a 2-fold increased dry biomass accumulation compared to growth without glucose. This was accompanied by increased cellular volume. Laser scattering characteristics during flow cytometry were used to estimate cell diameters and it was shown that an empirical but nonlinear relationship could be shown between flow cytometric pulse width and dry weight biomass per cell. This relationship could be linearised by the use of hypertonic conditions (1 M NaCl) to dehydrate the cells, as shown by density gradient centrifugation. Flow cytometry for biomass estimation is easy to perform, sensitive and offers more comprehensive information than optical density measurements. In addition, periodic flow cytometry measurements can be used to calibrate OD750 measurements for both convenience and accuracy. This approach is particularly useful for small samples and where cellular characteristics, especially cell size, are expected to vary during growth. PMID

Zooplankton biomass (displacement volume, dry mass, ash-free dry mass) data collected in Eastern Central Atlantic during CIPREA project from 1978-07-25 to 1978-09-12 by France (NODC Accession 0070783)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Zooplankton biomass (displacement volume, dry mass, and ashfree dry mass) data collected in Eastern Central Atlantic during CIPREA project in Jul - Sep 1978 by...

Individual tree size inequality enhances aboveground biomass in homegarden agroforestry systems in the dry zone of Sri Lanka.

Science.gov (United States)

Ali, Arshad; Mattsson, Eskil

2017-01-01

Individual tree size variation, which is generally quantified by variances in tree diameter at breast height (DBH) and height in isolation or conjunction, plays a central role in ecosystem functioning in both controlled and natural environments, including forests. However, none of the studies have been conducted in homegarden agroforestry systems. In this study, aboveground biomass, stand quality, cation exchange capacity (CEC), DBH variation, and species diversity were determined across 45 homegardens in the dry zone of Sri Lanka. We employed structural equation modeling (SEM) to test for the direct and indirect effects of stand quality and CEC, via tree size inequality and species diversity, on aboveground biomass. The SEM accounted for 26, 8, and 1% of the variation in aboveground biomass, species diversity and DBH variation, respectively. DBH variation had the strongest positive direct effect on aboveground biomass (β=0.49), followed by the non-significant direct effect of species diversity (β=0.17), stand quality (β=0.17) and CEC (β=-0.05). There were non-significant direct effects of CEC and stand quality on DBH variation and species diversity. Stand quality and CEC had also non-significant indirect effects, via DBH variation and species diversity, on aboveground biomass. Our study revealed that aboveground biomass substantially increased with individual tree size variation only, which supports the niche complementarity mechanism. However, aboveground biomass was not considerably increased with species diversity, stand quality and soil fertility, which might be attributable to the adaptation of certain productive species to the local site conditions. Stand structure shaped by few productive species or independent of species diversity is a main determinant for the variation in aboveground biomass in the studied homegardens. Maintaining stand structure through management practices could be an effective approach for enhancing aboveground biomass in these dry

Volume and Aboveground Biomass Models for Dry Miombo Woodland in Tanzania

Directory of Open Access Journals (Sweden)

Ezekiel Edward Mwakalukwa

2014-01-01

Full Text Available Tools to accurately estimate tree volume and biomass are scarce for most forest types in East Africa, including Tanzania. Based on a sample of 142 trees and 57 shrubs from a 6,065 ha area of dry miombo woodland in Iringa rural district in Tanzania, regression models were developed for volume and biomass of three important species, Brachystegia spiciformis Benth. (n = 40, Combretum molle G. Don (n = 41, and Dalbergia arbutifolia Baker (n = 37 separately, and for broader samples of trees (28 species, n = 72, shrubs (16 species, n = 32, and trees and shrubs combined (44 species, n = 104. Applied independent variables were log-transformed diameter, height, and wood basic density, and in each case a range of different models were tested. The general tendency among the final models is that the fit improved when height and wood basic density were included. Also the precision and accuracy of the predictions tended to increase from general to species-specific models. Except for a few volume and biomass models developed for shrubs, all models had R2 values of 96–99%. Thus, the models appear robust and should be applicable to forests with similar site conditions, species, and diameter ranges.

Use of cheese whey for biomass production and spray drying of probiotic lactobacilli.

Science.gov (United States)

Lavari, Luisina; Páez, Roxana; Cuatrin, Alejandra; Reinheimer, Jorge; Vinderola, Gabriel

2014-08-01

The double use of cheese whey (culture medium and thermoprotectant for spray drying of lactobacilli) was explored in this study for adding value to this wastewater. In-house formulated broth (similar to MRS) and dairy media (cheese and ricotta whey and whey permeate) were assessed for their capacity to produce biomass of Lactobacillus paracasei JP1, Lb. rhamnosus 64 and Lb. gasseri 37. Simultaneously, spray drying of cheese whey-starch solution (without lactobacilli cells) was optimised using surface response methodology. Cell suspensions of the lactobacilli, produced in in house-formulated broth, were spray-dried in cheese whey-starch solution and viability monitored throughout the storage of powders for 2 months. Lb. rhamnosus 64 was able to grow satisfactorily in at least two of the in-house formulated culture media and in the dairy media assessed. It also performed well in spray drying. The performance of the other strains was less satisfactory. The growth capacity, the resistance to spray drying in cheese whey-starch solution and the negligible lost in viability during the storage (2 months), makes Lb. rhamnosus 64 a promising candidate for further technological studies for developing a probiotic dehydrated culture for foods, utilising wastewaters of the dairy industry (as growth substrate and protectant) and spray drying (a low-cost widely-available technology).

Experimental studies on drying of Zingiber officinale, Curcuma longa l. and Tinospora cordifolia in solar-biomass hybrid drier

Energy Technology Data Exchange (ETDEWEB)

Prasad, J.; Vijay, V.K. [Indian Institute of Technology, New Delhi (India). Center for Rural Development and Technology

2005-11-01

An integral type natural convection solar drier has been fabricated and coupled with a biomass stove. Experiments have been conducted to test the performance of the drier by drying of Zingiber officinale (ginger), Curcuma longa l. (turmeric) and Tinospora cordifolia (guduchi) during the summer climate in Delhi. It was found that, during the load test for ginger, 18 kg of fresh product with an initial moisture content of 319.74(db)% was dried to a final moisture content of 11.8(db)% within 33 h. Similarly, moisture content of turmeric and guduchi were reduced from 358.96 to 8.8 and 257.45 to 9.67(db)% during 36 and 48 h of drying, respectively. The drying of these products has also been studied under 'solar-only' and open sun in the same climatic conditions and the results indicate that for all the products, drying is faster, and is within 33-48 h in hybrid drier, against 72-120 h in 'solar-only' operation of the same drier and 192-288 h in open sun. Efficiency of the drier during its two mode (solar and biomass separately) of operation has been estimated and quality evaluation of under-studied products showed that developed drier is suitable for the drying of these products. The developed drier is a simple system, which can be manufactured locally and can be used for drying of other agricultural products. (author)

A Preliminary Study on Rock Bed Heat Storage from Biomass Combustion for Rice Drying

Science.gov (United States)

Nelwan, L. O.; Wulandani, D.; Subrata, I. D. M.

2018-05-01

One of the main constraints of biomass fuel utilization in a small scale rice drying system is the operating difficulties related to the adjustment of combustion/feeding rate. Use of thermal storage may reduce the problem since combustion operation can be accomplished in a much shorter time and then the use of heat can be regulated by simply adjusting the air flow. An integrated biomass furnace-rock bed thermal storage with a storage volume of 540 L was designed and tested. There were four experiments conducted in this study. Charging was performed within 1-2 hours with a combustion rate of 11.5-15.5 kg/h. In discharging process, the mixing of air passing through the rock bed and ambient air were regulated by valves. Without adjusting the valve during the discharging process, air temperature increased up to 80°C, which is not suitable for rice batch drying process. Charging with sufficiently high combustion rate (14 kg/h) within 1 hour continued by adjusting the valve during discharging process below 60°C increased the discharge-charge time ratio (DCTR) up to 5.33 at average air temperature of 49°C and ambient temperature of 33°C.The efficiency of heat discharging was ranged from 34.5 to 45.8%. From the simulation, as much as 156.8-268.8 kg of rice was able to be dried by the discharging conditions.

Drying and heat decomposition of biomass during the production of biochar

Science.gov (United States)

Lyubov, V. K.; Popova, E. I.

2017-11-01

The process of wood torrefaction provides an opportunity to combine properties of biofuel and steam coal. Different degrees of biofuel heat treating leads to varied outcomes and varied biochar heating value. Therefore, the torrefaction process requires optimal operation that ensures the highest heating value of biochar with the lowest energy loss. In this paper we present the experimental results of drying cycle and thermal decomposition of particles of spruce stem wood and hydrolytic lignin in argon under various temperature conditions and basic material humidity as well as changes in the morphological structure of the biomass and its grain size composition during the torrefaction.

Recovery of Biomass Following Shifting Cultivation in Dry Tropical Forests of the Yucatan

OpenAIRE

Read, L; Lawrence, Deborah; Foster, David Russell

2003-01-01

Land-use change in the tropics is creating secondary forest at an unprecedented rate. In the tropical Americas, mature dry tropical forest is rapidly being converted to secondary forest during the fallow period of shifting cultivation. This study addresses changes in forest biomass during forest recovery following shifting cultivation of maize (corn) in the Southern Yucatan Peninsular Region (SYPR), Mexico. We sampled stems .1 cm diameter at breast height at 36 study sites in t...

Performance Analysis of Solar Assisted Fluidized Bed Dryer Integrated Biomass Furnace with and without Heat Pump for Drying of Paddy

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performances of a solar assisted fluidized bed dryer integrated biomass furnace (SA-FBDIBF and a solar assisted heat pump fluidized bed dryer integrated biomass furnace (SAHP-FBDIBF for drying of paddy have been evaluated, and also drying kinetics of paddy were determined. The SA-FBDIBF and the SAHP-FBDIBF were used to dry paddy from 11 kg with moisture content of 32.85% db to moisture content of 16.29% db (14% wb under an air mass flow rate of 0.1037 kg/s within 29.73 minutes and 22.95 minutes, with average temperatures and relative humidities of 80.3°C and 80.9°C and 12.28% and 8.14%, respectively. The average drying rate, specific energy consumption, and specific moisture extraction rate were 0.043 kg/minute and 0.050 kg/minute, 5.454 kWh/kg and 4.763 kWh/kg, and 0.204 kg/kWh and 0.241 kg/kWh for SA-FBDIBF and SAHP-FBDIBF, respectively. In SA-FBDIBF and SAHP-FBDIBF, the dryer thermal efficiencies were average values of 12.28% and 15.44%; in addition, the pickup efficiencies were 33.55% and 43.84% on average, whereas the average solar and biomass fractions were 10.9% and 10.6% and 36.6% and 30.4% for SA-FBDIBF and SAHP-FBDIBF, respectively. The drying of paddy occurred in the falling rate period. The experimental dimensionless moisture content data were fitted to three mathematical models. Page’s model was found best to describe the drying behaviour of paddy.

Biomass burning emissions in north Australia during the early dry season: an overview of the 2014 SAFIRED campaign

OpenAIRE

M. D. Mallet; M. J. Desservettaz; B. Miljevic; A. Milic; Z. D. Ristovski; J. Alroe; L. T. Cravigan; E. R. Jayaratne; C. Paton-Walsh; D. W. T. Griffith; S. R. Wilson; G. Kettlewell; M. V. van der Schoot; P. Selleck; F. Reisen

2017-01-01

The SAFIRED (Savannah Fires in the Early Dry Season) campaign took place from 29 May until 30 June 2014 at the Australian Tropical Atmospheric Research Station (ATARS) in the Northern Territory, Australia. The purpose of this campaign was to investigate emissions from fires in the early dry season in northern Australia. Measurements were made of biomass burning aerosols, volatile organic compounds, polycyclic aromatic carbons, greenhouse gases, radon, speciated atmospheric ...

[Conversion methods of freshwater snail tissue dry mass and ash free dry mass].

Science.gov (United States)

Zhao, Wei-Hua; Wang, Hai-Jun; Wang, Hong-Zhu; Liu, Xue-Qin

2009-06-01

Mollusk biomass is usually expressed as wet mass with shell, but this expression fails to represent real biomass due to the high calcium carbonate content in shells. Tissue dry mass and ash free dry mass are relatively close to real biomass. However, the determination process of these two parameters is very complicated, and thus, it is necessary to establish simple and practical conversion methods for these two parameters. A total of six taxa of freshwater snails (Bellamya sp., Alocinma longicornis, Parafossarulus striatulus, Parafossarulus eximius, Semisulcospira cancellata, and Radix sp.) common in the Yangtze Basin were selected to explore the relations of their five shell dimension parameters, dry and wet mass with shells with their tissue dry mass and ash free dry mass. The regressions of the tissue dry mass and ash free dry mass with the five shell dimension parameters were all exponential (y = ax(b)). Among them, shell width and shell length were more precise (the average percentage error between observed and predicted value being 22.0% and 22.5%, respectively) than the other three parameters in the conversion of dry mass. Wet mass with shell could be directly converted to tissue dry mass and ash free dry mass, with an average percentage error of 21.7%. According to the essence of definition and the errors of conversion, ash free dry mass would be the optimum parameter to express snail biomass.

Pan tropical biomass equations for Mexico's dry forests

Directory of Open Access Journals (Sweden)

José Návar

2014-12-01

Full Text Available This study reports a set of robust regional M-tree allometric equations for Mexico's tropical dry forests and their application to a forest inventory dataset for the States of Durango and Sinaloa, Mexico. Calculated M data from 15 reported equations were fitted, applied and validated for regional and global models. Proposed theoretical models, empirically derived equations, as well as global and local reported equations were fitted and applied to calculated M-tree data using wood specific gravity, diameter at breast height, and top height as exogenous variables. Empirically-derived, computer-based equations assessed the M-tree evaluations slightly better than the theoretical, the global and the local models. However, the theoretical models projected compatible M-tree values and deserve further attention once wood specific gravity data are collected in the field. Using the best fit equation, mean M plot density values of 30, 41 and 35 Mg ha-1 were estimated from 57 plots (1,600 m² each, 217 plots (1,000 m² each and 166 plots (1,000 m² each in the tropical dry forests of the States of Durango, Tiniaquis and Vado Hondo (Sinaloa, respectively. The large sample size, the richness of the tested allometric models, the economic and ecological importance of this data-source, and the spatial coverage of these equations made this dataset uniquely useful for biomass, charcoal, and other bio-energy estimations, as well as for understanding the inherent heterogeneity of the stand-structure in dynamic tropical forest environments.

Biomass burning emissions in north Australia during the early dry season: an overview of the 2014 SAFIRED campaign

OpenAIRE

Mallet, Marc D.; Desservettaz, Maximilien J.; Miljevic, Branka; Milic, Andelija; Ristovski, Zoran D.; Alroe, Joel; Cravigan, Luke T.; Jayaratne, E. Rohan; Paton-Walsh, Clare; Griffith, David W. T.; Wilson, Stephen R.; Kettlewell, Graham; Schoot, Marcel V.; Selleck, Paul; Reisen, Fabienne

2016-01-01

The SAFIRED (Savannah Fires in the Early Dry Season) campaign took place from 29th of May, 2014 until the 30th June, 2014 at the Australian Tropical Atmospheric Research Station (ATARS) in the Northern Territory, Australia. The purpose of this campaign was to investigate emissions from fires in the early dry season in northern Australia. Measurements were made of biomass burning aerosols, volatile organic compounds, polycyclic aromatic carbons, greenhouse gases, radon, mercury cycle, and trac...

Removal of zinc by live, dead, and dried biomass of Fusarium spp. isolated from the abandoned-metal mine in South Korea and its perspective of producing nanocrystals

International Nuclear Information System (INIS)

Velmurugan, Palanivel; Shim, Jaehong; You, Youngnam; Choi, Songho; Kamala-Kannan, Seralathan; Lee, Kui-Jae; Kim, Hee Joung; Oh, Byung-Taek

2010-01-01

Bioremediation is an innovative and alternative technology to remove heavy metal pollutants from aqueous solution using biomass from various microorganisms like algae, fungi and bacteria. In this study biosorption of zinc onto live, dead and dried biomass of Fusarium spp. was investigated as a function of initial zinc(II) concentration, pH, temperature, agitation and inoculum volume. It was observed that dried, dead and live biomass efficiently removed zinc at 60 min at an initial pH of 6.0 ± 0.3. Temperature of 40 deg. C was optimum at agitation speed of 150 or 200 rpm. The initial metal concentration (10-320 mg L -1 ) significantly influenced the biosorption of the fungi. Overall, biosorption was high with 30-60% by dried, live and dead biomass. In addition to this, the potential of Fusarium spp. to produce zinc nanocrystals was determined by transmission electron microscopy, energy-dispersive spectroscopy, X-ray diffraction and fourier transform infrared spectroscopy, which showed that dead biomass was not significantly involved in production of zinc nanocrystals.

Removal of zinc by live, dead, and dried biomass of Fusarium spp. isolated from the abandoned-metal mine in South Korea and its perspective of producing nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Velmurugan, Palanivel; Shim, Jaehong; You, Youngnam; Choi, Songho; Kamala-Kannan, Seralathan; Lee, Kui-Jae [Division of Biotechnology, Advanced institute of Environment and Bioscience, College of Environmental and Bioresource Sciences, Chonbuk National University, Iksan, Jeonbuk 570-752 (Korea, Republic of); Kim, Hee Joung [Institute of Environmental Research, Kangwon National University, Chuncheon 200-701 (Korea, Republic of); Oh, Byung-Taek, E-mail: btoh@jbnu.ac.kr [Division of Biotechnology, Advanced institute of Environment and Bioscience, College of Environmental and Bioresource Sciences, Chonbuk National University, Iksan, Jeonbuk 570-752 (Korea, Republic of)

2010-10-15

Bioremediation is an innovative and alternative technology to remove heavy metal pollutants from aqueous solution using biomass from various microorganisms like algae, fungi and bacteria. In this study biosorption of zinc onto live, dead and dried biomass of Fusarium spp. was investigated as a function of initial zinc(II) concentration, pH, temperature, agitation and inoculum volume. It was observed that dried, dead and live biomass efficiently removed zinc at 60 min at an initial pH of 6.0 {+-} 0.3. Temperature of 40 deg. C was optimum at agitation speed of 150 or 200 rpm. The initial metal concentration (10-320 mg L{sup -1}) significantly influenced the biosorption of the fungi. Overall, biosorption was high with 30-60% by dried, live and dead biomass. In addition to this, the potential of Fusarium spp. to produce zinc nanocrystals was determined by transmission electron microscopy, energy-dispersive spectroscopy, X-ray diffraction and fourier transform infrared spectroscopy, which showed that dead biomass was not significantly involved in production of zinc nanocrystals.

Long-term changes in above ground biomass after disturbance in a neotropical dry forest, Hellshire Hills, Jamaica

DEFF Research Database (Denmark)

Niño, Milena; McLaren, Kurt P.; Meilby, Henrik

2014-01-01

We used data from experimental plots (control, partially cut and clear-cut) established in 1998, in a tropical dry forest (TDF) in Jamaica, to assess changes in above ground biomass (AGB) 10 years after disturbance. The treatments reduced AGB significantly in 1999 (partially cut: 37.6 %, clear-cu...

Effects of different biomass drying and lipid extraction methods on algal lipid yield, fatty acid profile, and biodiesel quality.

Science.gov (United States)

Hussain, Javid; Liu, Yan; Lopes, Wilson A; Druzian, Janice I; Souza, Carolina O; Carvalho, Gilson C; Nascimento, Iracema A; Liao, Wei

2015-03-01

Three lipid extraction methods of hexane Soxhlet (Sox-Hex), Halim (HIP), and Bligh and Dyer (BD) were applied on freeze-dried (FD) and oven-dried (OD) Chlorella vulgaris biomass to evaluate their effects on lipid yield, fatty acid profile, and algal biodiesel quality. Among these three methods, HIP was the preferred one for C. vulgaris lipid recovery considering both extraction efficiency and solvent toxicity. It had the highest lipid yields of 20.0 and 22.0% on FD and OD biomass, respectively, with corresponding neutral lipid yields of 14.8 and 12.7%. The lipid profiling analysis showed that palmitic, oleic, linoleic, and α-linolenic acids were the major fatty acids in the algal lipids, and there were no significant differences on the amount of these acids between different drying and extraction methods. Correlative models applied to the fatty acid profiles concluded that high contents of palmitic and oleic acids in algal lipids contributed to balancing the ratio of saturated and unsaturated fatty acids and led to a high-quality algal biodiesel.

Surplus biomass through energy efficient kilns

International Nuclear Information System (INIS)

Anderson, Jan-Olof; Westerlund, Lars

2011-01-01

Highlights: → The magnitude of the national heat demand for drying lumber in kilns is established. → Each part of the total heat consumption is divided and shown between the main drying conditions. → The potential to increase the energy efficiency in kilns with available techniques is presented. → The market demand for the biomass, available with increase kiln energy efficiency, is reviled. -- Abstract: The use of biomass in the European Union has increased since the middle of the 1990s, mostly because of high subsidies and CO 2 emission regulation through the Kyoto protocol. The sawmills are huge biomass suppliers to the market; out of the Swedish annual lumber production of 16.4 Mm 3 , 95% is produced by medium to large-volume sawmills with a lumber quotient of 47%. The remaining part is produced as biomass. An essential part (12%) of the entering timber is used for supply of heat in their production processes, mostly in the substantial drying process. The drying process is the most time and heat consuming process in the sawmill. This study was undertaken to determine the sawmills' national use of energy and potential magnitude of improvements. If the drying process can be made more effective, sawmills' own use of biomass can be decreased and allow a considerably larger supply to the biomass market through processed or unprocessed biomass, heat or electricity production. The national electricity and heat usage when drying the lumber have been analysed by theoretical evaluation and experimental validation at a batch kiln. The main conclusion is that the heat consumption for drying lumber among the Swedish sawmills is 4.9 TW h/year, and with available state-of-the-art techniques it is possible to decrease the national heat consumption by approximately 2.9 TW h. This additional amount of energy corresponds to the market's desire for larger energy supply.

Tracking dynamics of plant biomass composting by changes in substrate structure, microbial community, and enzyme activity

Science.gov (United States)

2012-01-01

Background Understanding the dynamics of the microbial communities that, along with their secreted enzymes, are involved in the natural process of biomass composting may hold the key to breaking the major bottleneck in biomass-to-biofuels conversion technology, which is the still-costly deconstruction of polymeric biomass carbohydrates to fermentable sugars. However, the complexity of both the structure of plant biomass and its counterpart microbial degradation communities makes it difficult to investigate the composting process. Results In this study, a composter was set up with a mix of yellow poplar (Liriodendron tulipifera) wood-chips and mown lawn grass clippings (85:15 in dry-weight) and used as a model system. The microbial rDNA abundance data obtained from analyzing weekly-withdrawn composted samples suggested population-shifts from bacteria-dominated to fungus-dominated communities. Further analyses by an array of optical microscopic, transcriptional and enzyme-activity techniques yielded correlated results, suggesting that such population shifts occurred along with early removal of hemicellulose followed by attack on the consequently uncovered cellulose as the composting progressed. Conclusion The observed shifts in dominance by representative microbial groups, along with the observed different patterns in the gene expression and enzymatic activities between cellulases, hemicellulases, and ligninases during the composting process, provide new perspectives for biomass-derived biotechnology such as consolidated bioprocessing (CBP) and solid-state fermentation for the production of cellulolytic enzymes and biofuels. PMID:22490508

Shorea robusta: A sustainable biomass feedstock

Directory of Open Access Journals (Sweden)

Vishal Kumar Singh

2016-09-01

Full Text Available The biomass feedstock needs to be available in a manner that is sustainable as well as renewable. However, obtaining reliable and cost effective supplies of biomass feedstock produced in a sustainable manner can prove to be difficult. Traditional biomass, mainly in the form of fallen leaves, fuel wood or dried dung, has long been the renewable and sustainable energy source for cooking and heating. Present study accounts for the biomass of fallen leaves of Shorea robusta, also known as sal, sakhua or shala tree, in the campus of BIT Mesra (Ranchi. These leaves are being gathered and burnt rather than being sold commercially. They contain water to varying degrees which affects their energy content. Hence, measurement of moisture content is critical for its biomass assessment. The leaves were collected, weighed, oven dried at 100oC until constant weight, then dry sample was reweighed to calculate the moisture content that has been driven off. By subtraction of moisture content from the initial weight of leaves, biomass was calculated. Using Differential Scanning Calorimeter (DSC the heat content of the leaves was calculated and the elemental analysis of leaf was done by CHNSO elemental analyser. Further, total biomass and carbon content of Sal tree was calculated using allometric equations so as to make a comparison to the biomass stored in dried fallen leaves

Soil respiration, microbial biomass and exoenzyme activity in switchgrass stands under nitrogen fertilization management and climate warming.

Science.gov (United States)

Jian, S.; Li, J.; de Koff, J.; Celada, S.; Mayes, M. A.; Wang, G.; Guo, C.

2016-12-01

Switchgrass (Panicum virgatum L.), as a model bioenergy crop, received nitrogen fertilizers for increasing its biomass yields. Studies rarely investigate the interactive effects of nitrogen fertilization and climate warming on soil microbial activity and carbon cycling in switchgrass cropping systems. Enhanced nitrogen availability under fertilization can alter rates of soil organic matter decomposition and soil carbon emissions to the atmosphere and thus have an effect on climate change. Here, we assess soil CO2 emission, microbial biomass and exoenzyme activities in two switchgrass stands with no fertilizer and 60 lbs N / acre. Soils were incubated at 15 ºC and 20 ºC for 180-day. Dry switchgrass plant materials were added to incubation jars and the 13C stable isotopic probing technique was used to monitor soil CO2 respiration derived from relatively labile litter and indigenous soil. Measurements of respiration, δ13C of respiration, microbial biomass carbon and exoenzyme activity were performed on days 1, 5, 10, 15, 30, 60, 90, 120, 150 and 180. Soil respiration rate was greater in the samples incubated at 20 ºC as compared to those incubated at 15 ºC. Exoenzyme activities were significantly altered by warming, litter addition and nitrogen fertilization. There was a significant interactive effect of nitrogen fertilization and warming on the proportion of CO2 respired from soils such that nitrogen fertilization enhanced warming-induced increase by 12.0% (Pmineralization. Fertilization increased soil microbial biomass carbon at both temperatures (9.0% at 15 ºC and 14.5% at 20 ºC). Our preliminary analysis suggested that warming effects on enhanced soil respiration can be further increased with elevated fertilizer input via greater microbial biomass and exoenzyme activity. In addition to greater biomass yield under N fertilization, this study informs potential soil carbon loss from stimulated soil respiration under nitrogen fertilization and warming in

Shifts in biomass and productivity for a subtropical dry forest in response to simulated elevated hurricane disturbances

International Nuclear Information System (INIS)

Holm, Jennifer A.; Van Bloem, Skip J.; Larocque, Guy R.; Shugart, Herman H.

2017-01-01

Caribbean tropical forests are subject to hurricane disturbances of great variability. In addition to natural storm incongruity, climate change can alter storm formation, duration, frequency, and intensity. This model -based investigation assessed the impacts of multiple storms of different intensities and occurrence frequencies on the long-term dynamics of subtropical dry forests in Puerto Rico. Using the previously validated individual-based gap model ZELIG-TROP, we developed a new hurricane damage routine and parameterized it with site- and species-specific hurricane effects. A baseline case with the reconstructed historical hurricane regime represented the control condition. Ten treatment cases, reflecting plausible shifts in hurricane regimes, manipulated both hurricane return time (i.e. frequency) and hurricane intensity. The treatment-related change in carbon storage and fluxes were reported as changes in aboveground forest biomass (AGB), net primary productivity (NPP), and in the aboveground carbon partitioning components, or annual carbon accumulation (ACA). Increasing the frequency of hurricanes decreased aboveground biomass by between 5% and 39%, and increased NPP between 32% and 50%. Decadal-scale biomass fluctuations were damped relative to the control. In contrast, increasing hurricane intensity did not create a large shift in the long-term average forest structure, NPP, or ACA from that of historical hurricane regimes, but produced large fluctuations in biomass. Decreasing both the hurricane intensity and frequency by 50% produced the highest values of biomass and NPP. For the control scenario and with increased hurricane intensity, ACA was negative, which indicated that the aboveground forest components acted as a carbon source. However, with an increase in the frequency of storms or decreased storms, the total ACA was positive due to shifts in leaf production, annual litterfall, and coarse woody debris inputs, indicating a carbon sink into the

Energy efficient thermochemical conversion of very wet biomass to biofuels by integration of steam drying, steam electrolysis and gasification

DEFF Research Database (Denmark)

Clausen, Lasse Røngaard

2017-01-01

A novel system concept is presented for the thermochemical conversion of very wet biomasses such as sewage sludge and manure. The system integrates steam drying, solid oxide electrolysis cells (SOEC) and gasification for the production of synthetic natural gas (SNG). The system is analyzed...

A rice husk gasifier for paddy drying

International Nuclear Information System (INIS)

Mirani, A.A.; Kalwar, S.A.; Ahmad, M.

2013-01-01

Due to energy crisis and constant increase in the price of fossil fuels, the world's trend changes to renewable sources of energy like solar, wind and biomass gasification. Substantial biomass potential is available in Pakistan in the form of agriculture or forest residue (rice straw, rice husk, cotton stalks, corn cobs, wood chips, wood saw, etc.). These can be best utilised for the production of producer gas or synthetic gas that can be used for drying of agricultural crops. The drying process is an important activity of post harvest processing for long-term storage. Rice husk is nowadays commonly used for biomass gasification and its heat content value is about 15MJ/kg. It constitutes about 30 percent of rice production. A rice husk gasifier was developed and evaluated on paddy drying at Japan International Cooperation Agency (JICA), Tsukuba International Center (TBIC), Japan. Rice husk gasifier has following major components; husk feeding system, ash chamber, burner, centrifugal fan, drying chamber, gasifier reactor, air duct and an electric motor of 0.37kW. The average drying plenum air temperature was recorded as 45 degree C during the drying process. The paddy 'IR 28' from initial moisture content of 24% was dried up to 14% moisture content for about 3.33h consuming 3kg/h of rice husk. The efficiency was found to be 58%. The rice husk gasifier can also be used for drying the fruits and vegetables, provided that heat exchanger should be attached with it. The overall performance of rice husk gasifier was satisfactory and will be beneficial for small scale farmers, food processors and millers as well. (author)

Phosphorus fractions, microbial biomass and enzyme activities in ...

African Journals Online (AJOL)

Potohar, northern Punjab, Pakistan in September, 2008 and analysed for P fractions and microbial parameters including microbial biomass C, microbial biomass N, microbial biomass P, and activities of dehydrogenase and alkaline phosphatase enzymes. The average size of different P fractions (% of total P) in the soils ...

Evaluation of various solvent systems for lipid extraction from wet microalgal biomass and its effects on primary metabolites of lipid-extracted biomass.

Science.gov (United States)

Ansari, Faiz Ahmad; Gupta, Sanjay Kumar; Shriwastav, Amritanshu; Guldhe, Abhishek; Rawat, Ismail; Bux, Faizal

2017-06-01

Microalgae have tremendous potential to grow rapidly, synthesize, and accumulate lipids, proteins, and carbohydrates. The effects of solvent extraction of lipids on other metabolites such as proteins and carbohydrates in lipid-extracted algal (LEA) biomass are crucial aspects of algal biorefinery approach. An effective and economically feasible algae-based oil industry will depend on the selection of suitable solvent/s for lipid extraction, which has minimal effect on metabolites in lipid-extracted algae. In current study, six solvent systems were employed to extract lipids from dry and wet biomass of Scenedesmus obliquus. To explore the biorefinery concept, dichloromethane/methanol (2:1 v/v) was a suitable solvent for dry biomass; it gave 18.75% lipids (dry cell weight) in whole algal biomass, 32.79% proteins, and 24.73% carbohydrates in LEA biomass. In the case of wet biomass, in order to exploit all three metabolites, isopropanol/hexane (2:1 v/v) is an appropriate solvent system which gave 7.8% lipids (dry cell weight) in whole algal biomass, 20.97% proteins, and 22.87% carbohydrates in LEA biomass. Graphical abstract: Lipid extraction from wet microalgal biomass and biorefianry approach.

Tracking dynamics of plant biomass composting by changes in substrate structure, microbial community, and enzyme activity

Directory of Open Access Journals (Sweden)

Wei Hui

2012-04-01

Full Text Available Abstract Background Understanding the dynamics of the microbial communities that, along with their secreted enzymes, are involved in the natural process of biomass composting may hold the key to breaking the major bottleneck in biomass-to-biofuels conversion technology, which is the still-costly deconstruction of polymeric biomass carbohydrates to fermentable sugars. However, the complexity of both the structure of plant biomass and its counterpart microbial degradation communities makes it difficult to investigate the composting process. Results In this study, a composter was set up with a mix of yellow poplar (Liriodendron tulipifera wood-chips and mown lawn grass clippings (85:15 in dry-weight and used as a model system. The microbial rDNA abundance data obtained from analyzing weekly-withdrawn composted samples suggested population-shifts from bacteria-dominated to fungus-dominated communities. Further analyses by an array of optical microscopic, transcriptional and enzyme-activity techniques yielded correlated results, suggesting that such population shifts occurred along with early removal of hemicellulose followed by attack on the consequently uncovered cellulose as the composting progressed. Conclusion The observed shifts in dominance by representative microbial groups, along with the observed different patterns in the gene expression and enzymatic activities between cellulases, hemicellulases, and ligninases during the composting process, provide new perspectives for biomass-derived biotechnology such as consolidated bioprocessing (CBP and solid-state fermentation for the production of cellulolytic enzymes and biofuels.

Drying enhances immunoactivity of spent brewer's yeast cell wall β-D-glucans.

Science.gov (United States)

Liepins, Janis; Kovačova, Elena; Shvirksts, Karlis; Grube, Mara; Rapoport, Alexander; Kogan, Grigorij

2015-07-20

Due to immunological activity, microbial cell wall polysaccharides are defined as 'biological response modifiers' (BRM). Cell walls of spent brewer's yeast also have some BRM activity. However, up to date there is no consensus on the use of spent brewer's yeast D-glucan as specific BRM in humans or animals. The aim of this paper is to demonstrate the potential of spent brewer's yeast β-D-glucans as BRM, and drying as an efficient pretreatment to increase β-D-glucan's immunogenic activity. Our results revealed that drying does not change spent brewer's yeast biomass carbohydrate content as well as the chemical structure of purified β-D-glucan. However, drying increased purified β-D-glucan TNF-α induction activity in the murine macrophage model. We presume drying pretreatment enhances purity of extracted β-D-glucan. This is corroborated with FT-IR analyses of the β-D-glucan spectra. Based on our results, we suggest that dry spent brewer's yeast biomass can be used as a cheap source for high-quality β-D-glucan extraction. Drying in combination with carboxylmethylation (CM), endows spent brewer's yeast β-D-glucan with the immunoactivity similar or exceeding that of a well-characterized fungal BRM pleuran. Copyright © 2015 Elsevier B.V. All rights reserved.

Characterization of biomasses, concentrates, and permeates of dried powder of Kombucha fermentation of spinach (Amaranthus sp.) and broccoli (Brassica oleracea) with membrane microfiltration and freeze drying techniques for natural sources of folic acid

Science.gov (United States)

Nugraha, Tutun; Susilowati, Agustine; Aspiyanto, Lotulung, Puspa Dewi; Maryati, Yati

2017-11-01

Fermentation of spinach (Amaranthus sp) and Broccoli (Brassica oleracea) using Kombucha Culture has been shown to produce biomass that has the potential to become natural sources of folic acid. To produce the materials, following the fermentation, the biomass was filtered using membrane microfiltration (0.15 µm) at a pressure of 40 psia, at room temperature, yielding the concentrate and the permeate fractions. Following this step, freeze drying process was done on the biomass feeds, as well as on the concentrate and permeate fractions. For the freeze drying stage, the samples were frozen, and the condenser was kept at -50°C for 40 hours, while the pressure in the chamber was set at 200 Pa. Freeze drying results showed that the final products, have differences in compositions, as well as differences in the dominat monomers of folates. After water content was driven out, freeze drying increased the concentrations of folic acid in the dried products, and was found to be the highest in the concentrate fractions. Freeze drying has been shown to be capable of protecting the folates from heat and oxidative damages that typicaly occur with other types of drying. The final freeze dried concentrates of fermentation of spinach and broccoli were found to contain folic acid at 2531.88 µg/mL and 1626.94 µg/mL, total solids at 87.23% and 88.65 %, total sugar at 22.66 µg/mL and 25.13 µg/mL, total reducing sugar at 34.46 mg/mL and 15.22 mg/mL, as well as disolved protein concentrations at 0.93 mg/mL and 1.45 mg/mL. Liquid Chromatography Mass Spectometry (LC-MS) identification of the folates in the freeze dried concentrates of fermented spinach and broccoli was done using folic acid and glutamic acid standard solutions as the reference materials. The results showed the presence of folic acid and showed that the dominant monomers of molecules of folates with molecular weights of 441.44 Da. and 441.54 Da. for spinach and broccoli respectively. Moreover, the monomers of glutamic

Drying behaviour, effective diffusivity and energy of activation of olive leaves dried by microwave, vacuum and oven drying methods

Science.gov (United States)

Elhussein, Elaf Abdelillah Ali; Şahin, Selin

2018-01-01

Drying is the crucial food processing for bioactive components from plant materials before strating extraction in addition to preservation of raw plant materials during storage period. Olive leaves were dried by various methods such as microwave drying (MD), oven drying (OD) and vacuum drying (VD) at several temperature values in the present study. Mathematical models allow to develop, design and control the processes. 14 emprical equations were used to estimate the drying behaviour and the time required for drying. Convenience of the models were evaluated according to the correlation coefficient (R 2 ), varience (S 2 ) and root mean square deviation (D RMS ). On the other hand, the effective diffusion coefficient and energy for activation were also calculated. Effects of the drying methods on the total phenolic (TPC), flavonoid (TFC) and oleuropein contents and free radical scavenging activity (FRSA) of the olive leaves were also investigated to take into considiration the quality of the dried product. MD has proved to be the fastest drying method having the highest effective diffusivity and the lowest activation energy with a more qualitive product.

Pilot scale harvesting, separation and drying of microalgae biomass from compact photo-bioreactor

Energy Technology Data Exchange (ETDEWEB)

Cardoso, Alberto Tadeu Martins; Luz Junior, Luiz Fernando de Lima [Dept. de Engenharia Quimica. Universidade Federal do Parana, Curitiba, PR (Brazil)], e-mail: luzjr@ufpr.br; Mariano, Andre Bellin; Ghidini, Luiz Francisco Correa; Gnoatto, Victor Eduardo; Locatelli Junior, Vilson; Mello, Thiago Carvalho de; Vargas, Jose Viriato Coelho [Nucleo de Pesquisa e Desenvolvimento em Energia Autossustentavel (NPDEAS). Dept. de Engenharia Mecanica. Universidade Federal do Parana, Curitiba (Brazil)], E-mail: jvargas@demec.ufpr.br

2010-07-01

Bio diesel produced from microalgae lipids is gaining a substantial ground in the search for renewable energy sources. In order to optimize the operating conditions of a continuous process, several experiments were realized, both in laboratory and pilot scale. The microalgae cultivation can be conducted in a photo-bioreactor, a closed system which allows parameters control and necessarily involves the aquatic environment. Because of that, the use of separation unit operations is required. The process starts in a proposed compact photo-bioreactor, which consist of a chain of transparent tubes with 6 cm of diameter arranged in parallel where the cultivation media circulate with the help of a pump. This arrangement offers a closed culture with less risk of contamination and maintains a minimum contact with the environment. The microalgae grow inside the pipes under incidence of ambient light. In this paper, harvesting, separation and drying were studied, as part of the processes of a sustainable energy plant under construction at UFPR, as shown in Fig. 1. To control the production in a photo-bioreactor in continuous system, it is necessary to monitor the concentration of microalgae growth in suspension. To measure the cell concentration in this equipment, an optic sensor has been developed. The microalgae biomass separation from the culture media is achieved by microalgae flocculation. Several cultivation situations have been tested with different NaOH concentrations, increasing the pH to 10. The system was kept under agitation during the addition by an air pump into the tank. Thereafter the system was maintained static. After a short time, it was observed that the microalgae coagulated and settled. The clarified part water was removed, remaining a concentrated microalgae suspension. Our results suggest that pH increase is a suitable methodology for microalgae separation from the growth suspension. The microalgae sedimentation time was recorded, which allowed the

Effects of climate and lifeform on dry matter yield (epsilon) from simulations using BIOME BGC. [ecosystem process model for vegetation biomass production using daily absorbed photosynthetically active radiation

Science.gov (United States)

Hunt, E. R., Jr.; Running, Steven W.

1992-01-01

An ecosystem process simulation model, BIOME-BGC, is used in a sensitivity analysis to determine the factors that may cause the dry matter yield (epsilon) and annual net primary production to vary for different ecosystems. At continental scales, epsilon is strongly correlated with annual precipitation. At a single location, year-to-year variation in net primary production (NPP) and epsilon is correlated with either annual precipitation or minimum air temperatures. Simulations indicate that forests have lower epsilon than grasslands. The most sensitive parameter affecting forest epsilon is the total amount of living woody biomass, which affects NPP by increasing carbon loss by maintenance respiration. A global map of woody biomass should significantly improve estimates of global NPP using remote sensing.

Solar dryer with thermal storage and biomass-backup heater

Energy Technology Data Exchange (ETDEWEB)

Madhlopa, A. [Department of Physics and Biochemical Sciences, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi); Ngwalo, G. [Department of Mechanical Engineering, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi)

2007-04-15

An indirect type natural convection solar dryer with integrated collector-storage solar and biomass-backup heaters has been designed, constructed and evaluated. The major components of the dryer are biomass burner (with a rectangular duct and flue gas chimney), collector-storage thermal mass and drying chamber (with a conventional solar chimney). The thermal mass was placed in the top part of the biomass burner enclosure. The dryer was fabricated using simple materials, tools and skills, and it was tested in three modes of operation (solar, biomass and solar-biomass) by drying twelve batches of fresh pineapple (Ananas comosus), with each batch weighing about 20 kg. Meteorological conditions were monitored during the dehydration process. Moisture and vitamin C contents were determined in both fresh and dried samples. Results show that the thermal mass was capable of storing part of the absorbed solar energy and heat from the burner. It was possible to dry a batch of pineapples using solar energy only on clear days. Drying proceeded successfully even under unfavorable weather conditions in the solar-biomass mode of operation. In this operational mode, the dryer reduced the moisture content of pineapple slices from about 669 to 11% (db) and yielded a nutritious dried product. The average values of the final-day moisture-pickup efficiency were 15%, 11% and 13% in the solar, biomass and solar-biomass modes of operation respectively. It appears that the solar dryer is suitable for preservation of pineapples and other fresh foods. Further improvements to the system design are suggested. (author)

Size distribution and hygroscopic properties of aerosol particles from dry-season biomass burning in Amazonia

Directory of Open Access Journals (Sweden)

J. Rissler

2006-01-01

Full Text Available Aerosol particle number size distributions and hygroscopic properties were measured at a pasture site in the southwestern Amazon region (Rondonia. The measurements were performed 11 September-14 November 2002 as part of LBA-SMOCC (Large scale Biosphere atmosphere experiment in Amazonia - SMOke aerosols, Clouds, rainfall and Climate, and cover the later part of the dry season (with heavy biomass burning, a transition period, and the onset of the wet period. Particle number size distributions were measured with a DMPS (Differential Mobility Particle Sizer, 3-850nm and an APS (Aerodynamic Particle Sizer, extending the distributions up to 3.3 µm in diameter. An H-TDMA (Hygroscopic Tandem Differential Mobility Analyzer measured the hygroscopic diameter growth factors (Gf at 90% relative humidity (RH, for particles with dry diameters (dp between 20-440 nm, and at several occasions RH scans (30-90% RH were performed for 165nm particles. These data provide the most extensive characterization of Amazonian biomass burning aerosol, with respect to particle number size distributions and hygroscopic properties, presented until now. The evolution of the convective boundary layer over the course of the day causes a distinct diel variation in the aerosol physical properties, which was used to get information about the properties of the aerosol at higher altitudes. The number size distributions averaged over the three defined time periods showed three modes; a nucleation mode with geometrical median diameters (GMD of ~12 nm, an Aitken mode (GMD=61-92 nm and an accumulation mode (GMD=128-190 nm. The two larger modes were shifted towards larger GMD with increasing influence from biomass burning. The hygroscopic growth at 90% RH revealed a somewhat external mixture with two groups of particles; here denoted nearly hydrophobic (Gf~1.09 for 100 nm particles and moderately hygroscopic (Gf~1.26. While the hygroscopic growth factors were surprisingly similar over the

Biomass torrefaction: A promising pretreatment technology for biomass utilization

Science.gov (United States)

Chen, ZhiWen; Wang, Mingfeng; Ren, Yongzhi; Jiang, Enchen; Jiang, Yang; Li, Weizhen

2018-02-01

Torrefaction is an emerging technology also called mild pyrolysis, which has been explored for the pretreatment of biomass to make the biomass more favorable for further utilization. Dry torrefaction (DT) is a pretreatment of biomass in the absence of oxygen under atmospheric pressure and in a temperature range of 200-300 degrees C, while wet torrrefaction (WT) is a method in hydrothermal or hot and high pressure water at the tempertures within 180-260 degrees C. Torrrefied biomass is hydrophobic, with lower moisture contents, increased energy density and higher heating value, which are more comparable to the characteristics of coal. With the improvement in the properties, torrefied biomass mainly has three potential applications: combustion or co-firing, pelletization and gasification. Generally, the torrefaction technology can accelerate the development of biomass utilization technology and finally realize the maximum applications of biomass energy.

Spatio-temporal Variations of Abundance, Biomass, and ...

African Journals Online (AJOL)

The spatio-seasonal variations of Pseudodiaptomus hessei abundance, biomass and reproductive parameters were investigated in the Grand-Lahou lagoon at five stations during the dry and wet (or rainy) seasons from September 2005 to August 2006. In all sampling stations, abundance and biomass of P. hessei in the dry ...

Biomass - Activities and projects in 2002; Biomasse Aktivitaeten und Projekte 2002. Ueberblicksbericht zum Forschungsprogramm 2002

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D.; Guggisberg, B.

2003-07-01

This annual report made for the Swiss Federal Office of Energy reviews the activities carried out under the Biomass Research Programme in 2002 and describes the various projects that were active during the year. The situation concerning energy supply from biomass is discussed and figures are presented on its share in total Swiss energy consumption. Three categories of biomass use are presented - burning, fermentation of wastes and biofuels. >From each of these categories, several pilot and demonstration projects are described that cover a wide range of technologies and research activities, ranging from the pre-processing of biogenic wastes through to the optimisation of biogas-based combined heat and power installations and the operational economics of compact biogas installations. The report is completed with lists of research and development projects and pilot and demonstration projects.

Local biomass burning is a dominant cause of the observed precipitation reduction in southern Africa

Science.gov (United States)

Hodnebrog, Øivind; Myhre, Gunnar; Forster, Piers M.; Sillmann, Jana; Samset, Bjørn H.

2016-01-01

Observations indicate a precipitation decline over large parts of southern Africa since the 1950s. Concurrently, atmospheric concentrations of greenhouse gases and aerosols have increased due to anthropogenic activities. Here we show that local black carbon and organic carbon aerosol emissions from biomass burning activities are a main cause of the observed decline in southern African dry season precipitation over the last century. Near the main biomass burning regions, global and regional modelling indicates precipitation decreases of 20–30%, with large spatial variability. Increasing global CO2 concentrations further contribute to precipitation reductions, somewhat less in magnitude but covering a larger area. Whereas precipitation changes from increased CO2 are driven by large-scale circulation changes, the increase in biomass burning aerosols causes local drying of the atmosphere. This study illustrates that reducing local biomass burning aerosol emissions may be a useful way to mitigate reduced rainfall in the region. PMID:27068129

Effects of different drying processes on the concentrations of metals and metalloids in plant materials

International Nuclear Information System (INIS)

Anawar, H.M.; Canha, N.; Freitas, M.C; Santa Regina, I.; Garcia-Sanchez, A.

2011-01-01

The drying process of fresh plant materials may affect the porous structure, dehydration and a number of quality characteristics of these materials. Therefore, this study has investigated the effect of different drying processes on the variation of metal and metalloid concentrations in the dried plant materials. Seven varieties of native plant species collected from Sao Domingos mine were analyzed by instrumental neutron activation analysis (INAA) to investigate the effects of freeze-drying (FD), ambient air-drying (AAD) and oven-drying (OD) process on the concentrations of metals and metalloids in the plant biomass. Comparison of ambient air-dried, oven-dried and freeze-dried preparations allows a phenomenological description of the dehydration artefacts. In the quantitative analysis of metals and metalloids, FD and OD plant samples show the higher concentrations of metals and metalloids when compared to those in the AAD plant biomass. The freeze-drying process is comparatively reliable for determination of metals and metalloids concentrations in plant materials. (author)

The opportunities for obtaining of the biogas on methane fermentation from marine algae biomass and water plant biomass

OpenAIRE

Jachniak Ewa; Chmura Joanna; Kuglarz Mariusz; Wiktor Józef

2018-01-01

The aim of the research was to try to obtain of the biogas on a laboratory scale from marine algae biomass and water plant biomass. The research was conducted in 2016 year and samples were taken from the Polish coast of the Baltic Sea. In laboratory work, algae and plant species were first identified. The next, in order to subject them to methane fermentation processes and to obtain biogas,partial mechanical treatment of the biomass was conducted. Dry matter content and dry organic matter con...

Review of the Drying Kinetics of Olive Oil Mill Wastes: Biomass Recovery

Directory of Open Access Journals (Sweden)

Francisco J. Gómez-de la Cruz

2015-06-01

Full Text Available The drying kinetics of olive oil mill wastes was analyzed based on experiments carried out by various researchers utilizing different drying systems. A critical review of the literature was done, and mathematical models of drying curves proposed by investigators were evaluated. A comparison between the best mathematical models of fit in the drying curves used in past experiments and a two-term Gaussian model was performed. This model improved all the results of fit in each experiment. Drying rates and drying stages were obtained and discussed. An average drying rate for each experiment from the two-term Gaussian model was calculated. This value allowed for visualizing and comparing the average speed of evaporated water in each experiment for the different dryers. Finally, and after having verified that almost all drying occurs mainly by a diffusion phenomenon, an analysis on the effective moisture diffusivity and activation energy values was performed. The results indicated that there was no dependency of these quantities on independent variables such as the drying air temperature, the drying air velocity, and the sample thickness. It follows that drying of olive oil mill wastes is a very complex physical process that depends heavily on aspects such as pieces of pit, pulp, skin, vegetation water, olive oil content, sugars and organics compounds of different nature.

Assessment of industrial activity in the utilization of biomass for energy

Energy Technology Data Exchange (ETDEWEB)

1980-09-01

The objective of this report is to help focus the federal programs in biomass energy, by identifying the status and objectives of private sector activity in the biomass field as of mid-1979. In addition, the industry's perceptions of government activities are characterized. Findings and conclusions are based principally on confidential interviews with executives in 95 companies. These included forest products companies, agricultural products companies, equipment manufacturers, electric and gas utilities petroleum refiners and distributors, research and engineering firms, and trade organizations, as listed in Exhibit 1. Interview findings have been supplemented by research of recent literature. The study focused on four key questions: (1) what is the composition of the biomass industry; (2) what are the companies doing; (3) what are their objectives and strategies; and (4) what are the implications for government policy. This executive summary provides highlights of the key findings and conclusions. The summary discussion is presented in seven parts: (1) overview of the biomass field; (2) structure of the biomass industry today; (3) corporate activities in biomass-related areas; (4) motivations for these activities; (5) industry's outlook on the future for energy-from-biomass; (6) industry's view of government activities; and (7) implications for Federal policy.

Biomass I. Science Activities in Energy [and] Teacher's Guide.

Science.gov (United States)

Oak Ridge Associated Universities, TN.

Designed for science students in fourth, fifth, and sixth grades, the activities in this unit illustrate principles and problems related to biomass as a form of energy. (The word biomass is used to describe all solid material of animal or vegetable origin from which energy may be extracted.) Twelve student activities using art, economics,…

Dry Bean Morpho-Physiological Responses to Gradual Weed Biomass Accumulation

Directory of Open Access Journals (Sweden)

Hossein GHAMARI

2013-02-01

Full Text Available Field study was carried out in 2011 in west of Iran to assess responses of dry bean (Phaseolus vulgaris L. morpho-physiological traits to gradual weed biomass accumulation. The treatments consisted of two different periods of weed interference, which weeds either infested the plots or removed for an increasing duration of time (0, 10, 20, 30, 40, 50 days after crop emergence. Relative dominance and relative importance of weed species fluctuated over the crop cycle. As the duration of weed interference was increased, a declining trend of crop growth rate (CGR was observed. When weeds were allowed to compete with crop throughout the crop cycle, maximum value of CGR was decreased from 25.57 g m-2 days in full season weed free treatment to 16.78 g m-2 days in full season weed infested treatment. Effect of treatments on leaf area index (LAI was significant. Weed removal increased LAI but it could not significantly affect this trait, at the early of growing season. Weed interference caused a significant reduction on number of branches. The minimum number of branches was registered in full season weed infested treatment (2.58 branches per plant, while the maximum one was observed in the full season weed free treatment (4.25 branches per plant. Weed competition severely reduced crop yield. At 10 and 20 days after crop emergence, weed infestation could not significantly affect the yield. A negative relationship between weeds’ dry matter accumulation and LAI as well as number of branches was observed which signify the vulnerability of these morpho-physiological traits to weed competition.

Experimental methods for laboratory-scale ensilage of lignocellulosic biomass

International Nuclear Information System (INIS)

Tanjore, Deepti; Richard, Tom L.; Marshall, Megan N.

2012-01-01

Anaerobic fermentation is a potential storage method for lignocellulosic biomass in biofuel production processes. Since biomass is seasonally harvested, stocks are often dried or frozen at laboratory scale prior to fermentation experiments. Such treatments prior to fermentation studies cause irreversible changes in the plant cells, influencing the initial state of biomass and thereby the progression of the fermentation processes itself. This study investigated the effects of drying, refrigeration, and freezing relative to freshly harvested corn stover in lab-scale ensilage studies. Particle sizes, as well as post-ensilage drying temperatures for compositional analysis, were tested to identify the appropriate sample processing methods. After 21 days of ensilage the lowest pH value (3.73 ± 0.03), lowest dry matter loss (4.28 ± 0.26 g. 100 g-1DM), and highest water soluble carbohydrate (WSC) concentrations (7.73 ± 0.26 g. 100 g-1DM) were observed in control biomass (stover ensiled within 12 h of harvest without any treatments). WSC concentration was significantly reduced in samples refrigerated for 7 days prior to ensilage (3.86 ± 0.49 g. 100 g −1 DM). However, biomass frozen prior to ensilage produced statistically similar results to the fresh biomass control, especially in treatments with cell wall degrading enzymes. Grinding to decrease particle size reduced the variance amongst replicates for pH values of individual reactors to a minor extent. Drying biomass prior to extraction of WSCs resulted in degradation of the carbohydrates and a reduced estimate of their concentrations. The methods developed in this study can be used to improve ensilage experiments and thereby help in developing ensilage as a storage method for biofuel production. -- Highlights: ► Laboratory-scale methods to assess the influence of ensilage biofuel production. ► Drying, freezing, and refrigeration of biomass influenced microbial fermentation. ► Freshly ensiled stover exhibited

Biomass derived graphene-like activated and non-activated porous ...

Indian Academy of Sciences (India)

these carbon materials confirm their promising characteristics for supercapacitor applications. ... Graphene; biomass; supercapacitor; porous carbon; energy storage. 1. .... activated carbon sheets, 2 g of starch and 1 g of pluronic F127.

System and process for biomass treatment

Science.gov (United States)

Dunson, Jr., James B; Tucker, III, Melvin P; Elander, Richard T; Lyons, Robert C

2013-08-20

A system including an apparatus is presented for treatment of biomass that allows successful biomass treatment at a high solids dry weight of biomass in the biomass mixture. The design of the system provides extensive distribution of a reactant by spreading the reactant over the biomass as the reactant is introduced through an injection lance, while the biomass is rotated using baffles. The apparatus system to provide extensive assimilation of the reactant into biomass using baffles to lift and drop the biomass, as well as attrition media which fall onto the biomass, to enhance the treatment process.

Above-ground biomass models for Seabuckthorn (Hippophae salicifolia) in Mustang District, Nepal

DEFF Research Database (Denmark)

Rajchal, Rajesh; Meilby, Henrik

2013-01-01

weight of fruit and oven-dry weight of wood (stem and branches) and leaves were measured and used as a basis for developing biomass models. Diameters of the trees were measured at 30 cm above ground whereas the heights were measured in terms of the total tree height (m). Among several models tested......, the models suggested for local use were: ln(woody biomass, oven-dry, kg) = -3.083 + 2.436 ln(diameter, cm), ln (fruit biomass, fresh, kg) = -3.237 + 1.346 ln(diameter, cm) and ln(leaf biomass, oven-dry, kg) = -4.013 + 1.403 ln(Diameter, cm) with adjusted coefficients of determination of 0.99, 0.73 and 0.......91 for wood, fruit, and leaves, respectively. The models suggested for a slightly broader range of environmental conditions were: ln (woody biomass, oven-dry, kg) = -3.277 + 0.924 ln(diameter2 × height), ln(Fruit biomass, fresh, kg) = -3.146 + 0.485 ln(diameter2 × height) and ln(leaf biomass, oven-dry, kg...

REDUCING ENVIRONMENTAL IMPACT AND COST OF PRODUCTION FOR DRYING FRUITS

Directory of Open Access Journals (Sweden)

Murad Erol

2013-12-01

Full Text Available To reduce the production costs for heat used in drying fruit plants was studied using of local biomass from tree branch pruning. The average annual get 3 t / ha biomass whit energy potential of 37 GJ/ha at a cost of up to 60 €/t. biomass at 10 - 50 mm chopped and dried below 20% can be gasefied with TLUD process characterized by high energy conversion efficiency, stability and safety in operation, emissions of CO and PM very low. TLUD process produces on average and 15% biochar that can be used as fuel or as agricultural amendment to increase fertility and for atmospheric carbon sequestration. There have been experiments simulated by model of USCMER 30/60MGB dryer equipped with two thermal modules TLUD FORTE-40 for apple slices drying heat of the apple prinings. Biomass used and biochar resulting chemical and energy were defined as micro-gasification process TLUD. That can dry 205 kg of apple slices in 6 hours with 74 kg of dry biomass to 10% of that remains and 12.2 kg biochar, biochar with or without 52 kg biomass, which costs € 8.55 or € 5.97, ie 4.3 or 6.1 times cheaper than diesel. On dry ton of sliced apple it can produce 59.6 kg biochar with soil seize -174.8 kg. CO2.

Biomass of tree species as a response to planting density and interspecific competition

Directory of Open Access Journals (Sweden)

Paulo Sérgio Lima e Silva

2014-04-01

Full Text Available Planting trees is an important way to promote the recovery of degraded areas in the Caatinga region. Experiments (E1, E2, and E3 were conducted in a randomized blocks design, with three, three, and five replicates, respectively. The objectives were to evaluate biomass of the shoots of: a gliricidia (G and sabiá (S, as a response to planting density; b G, S, and neem (N in competition; c G, and S in agroforestry. E1 was conducted in split-plots, and planting densities (400, 600, 800, 1000, and 1200 plants ha-1 as subplots. E2 consisted of a factorial comprising the following plots: GGG, NGN, SGS, NNN, GNG, SNS, SSS, GSG, NSN (each letter represents a row of plants. E3 was conducted with G and S in agroforestry experiment. The trees were harvested after 54, 42, and 27 months old, in E1, E2 and E3, respectively. In E1, G presented higher green biomass of the stems and leaf at smaller densities than S, but lower green biomass of branches at most densities. The species did not differ for mean stem dry biomass and leaf dry biomass, but G showed higher branch dry biomass at most densities. Higher planting densities increased green and dry biomass of stems, branches, and leaves in S, but decreased those characteristics in G, with the exception of leaf dry mass, which was not influenced by density. In E2, the behavior of each species was identical in plots containing the same or different species. Griricidia showed the highest green biomass of stems and branches, and the highest values for geren biomass of the leaf were observed for gliricidia and neem. The highest stem, branch, and leaf dry biomass values were obtained for G, S, and N, respectively. In E3, G was superior for stem and leaf green biomass, and for stem and branch dry biomass. There were no differences between species for the other biomass values.

Hot and Dry Cleaning of Biomass-Gasified Gas Using Activated Carbons with Simultaneous Removal of Tar, Particles, and Sulfur Compounds

Directory of Open Access Journals (Sweden)

Kinya Sakanishi

2012-05-01

Full Text Available This study proposes a gas-cleaning process for the simultaneous removal of sulfur compounds, tar, and particles from biomass-gasified gas using Fe-supported activated carbon and a water-gas shift reaction. On a laboratory scale, the simultaneous removal of H2S and COS was performed under a mixture of gases (H2/CO/CO2/CH4/C2H4/N2/H2S/COS/steam. The reactions such as COS + H2 → H2S + CO and COS + H2O → H2S + CO2 and the water-gas shift reaction were promoted on the Fe-supported activated carbon. The adsorption capacity with steam was higher than that without steam. On a bench scale, the removal of impurities from a gas derived from biomass gasification was investigated using two activated filters packed with Fe-supported activated carbon. H2S and COS, three- and four-ring polycyclic aromatic hydrocarbons (PAHs, and particles were removed and a water-gas shift reaction was promoted through the first filter at 320–350 °C. The concentrations of H2S and COS decreased to less than 0.1 ppmv. Particles and the one- and two-ring PAHs, except for benzene, were then removed through the second filter at 60–170 °C. The concentration of tar and particles decreased from 2428 to 102 mg Nm−3 and from 2244 to 181 mg Nm−3, respectively.

Woody biomass availability for bioethanol conversion in Mississippi

International Nuclear Information System (INIS)

Perez-Verdin, Gustavo; Grebner, Donald L.; Sun, Changyou; Munn, Ian A.; Schultz, Emily B.; Matney, Thomas G.

2009-01-01

This study evaluated woody biomass from logging residues, small-diameter trees, mill residues, and urban waste as a feedstock for cellulosic ethanol conversion in Mississippi. The focus on Mississippi was to assess in-state regional variations and provide specific information of biomass estimates for those facilities interested in locating in Mississippi. Supply and cost of four woody biomass sources were derived from Forest Inventory Analysis (FIA) information, a recent forest inventory conducted by the Mississippi Institute for Forest Inventory, and primary production costs. According to our analysis, about 4.0 million dry tons of woody biomass are available for production of up to 1.2 billion liters of ethanol each year in Mississippi. The feedstock consists of 69% logging residues, 21% small-diameter trees, 7% urban waste, and 3% mill residues. Of the total, 3.1 million dry tons (930 million liters of ethanol) can be produced for $34 dry ton -1 or less. Woody biomass from small-diameter trees is more expensive than other sources of biomass. Transportation costs accounted for the majority of total production costs. A sensitivity analysis indicates that the largest impacts in production costs of ethanol come from stumpage price of woody biomass and technological efficiency. These results provide a valuable decision support tool for resource managers and industries in identifying parameters that affect resource magnitude, type, and location of woody biomass feedstocks in Mississippi. (author)

Aboveground dry biomass partitioning and nitrogen accumulation in early maturing soybean ‘Merlin’

Directory of Open Access Journals (Sweden)

Tadeusz Zając

2017-12-01

Full Text Available The aim of the study was to determine the biomass and nitrogen accumulation in early maturing soybean plants experiencing contrasting weather conditions. Soybean (Glycine max is a species of agricultural crop plant that is widely described in scientific publications. During 2014–2016, a field experiment with early maturing soybean ‘Merlin’ was carried out at Grodziec Śląski, Poland (49°48'01" N, 18°52'04" E. Results showed that the morphological traits of the plants, the yield of individual plants, and the soybean crop were all closely related to the climatic conditions. A high amount of precipitation stimulated seed development, resulting in a high production potential. The harvest index calculated for soybean ‘Merlin’ was high and exceeded 0.5 g g−1. The nitrogen content of the aboveground biomass increased during ontogenesis. The maximum yield of dry matter was noted at the green maturity phase, which subsequently decreased at the full maturity phase because of the loss of the leaf fraction. The variation in the effectiveness of nitrogen accumulation in seeds between 2015 and 2016 was 30%. The nitrogen harvest index values were high in each year of the experiment and exceeded 0.92 g−1. For the production of 1 ton of seeds with an adequate amount of soybean straw, plants needed, on average, 68 kg of nitrogen.

Metal accumulation by sunflower (Helianthus annuus L. and the efficacy of its biomass in enzymatic saccharification.

Directory of Open Access Journals (Sweden)

Saurabh Sudha Dhiman

Full Text Available Accumulation of metal contaminants in soil as a result of various industrial and anthropogenic activities has reduced soil fertility significantly. Phytoextraction of metal contaminants can improve soil fertility and provide inexpensive feedstock for biorefineries. We investigated the hyperaccumulation capacity of sunflower (Helianthus annuus biomass by cultivating these plants in various concentrations of metal contaminants. Sunflowers were grown in soils contaminated with various levels of heavy metals (10-2,000 mg/kg dry soil. The degree of metal uptake by different parts of the biomass and the residual concentration in the soil were estimated through inductively coupled plasma mass spectrometry. An almost 2.5-fold hyperaccumulation of Zn2+ was observed in the leaf and flower biomass compared with the concentration in the soil. For the subsequent saccharification of biomass with hyperaccumulated contaminants, a fungal lignocellulosic consortium was used. The fungal consortium cocktail retained more than 95% filter paper activity with 100 mM Ni2+ ions even after 36 h. The highest saccharification yield (SY, 87.4% was observed with Ni2+ as the contaminant (10 mg/kg dry wt, whereas Pb2+ (251.9 mg/kg dry wt was the strongest inhibitor of biomass hydrolysis, resulting in only a 30% SY. Importantly, the enzyme cocktail produced by the fungal consortium resulted in almost the same SY (% as that obtained from a combination of commercial cellulase and β-glucosidase. Significant sugar conversion (61.7% from H. annuus biomass hydrolysate occurred, resulting in the production of 11.4 g/L of bioethanol. This is the first study to assess the suitability of phytoremediated sunflower biomass for bioethanol production.

Metal accumulation by sunflower (Helianthus annuus L.) and the efficacy of its biomass in enzymatic saccharification.

Science.gov (United States)

Dhiman, Saurabh Sudha; Zhao, Xin; Li, Jinglin; Kim, Dongwook; Kalia, Vipin C; Kim, In-Won; Kim, Jae Young; Lee, Jung-Kul

2017-01-01

Accumulation of metal contaminants in soil as a result of various industrial and anthropogenic activities has reduced soil fertility significantly. Phytoextraction of metal contaminants can improve soil fertility and provide inexpensive feedstock for biorefineries. We investigated the hyperaccumulation capacity of sunflower (Helianthus annuus) biomass by cultivating these plants in various concentrations of metal contaminants. Sunflowers were grown in soils contaminated with various levels of heavy metals (10-2,000 mg/kg dry soil). The degree of metal uptake by different parts of the biomass and the residual concentration in the soil were estimated through inductively coupled plasma mass spectrometry. An almost 2.5-fold hyperaccumulation of Zn2+ was observed in the leaf and flower biomass compared with the concentration in the soil. For the subsequent saccharification of biomass with hyperaccumulated contaminants, a fungal lignocellulosic consortium was used. The fungal consortium cocktail retained more than 95% filter paper activity with 100 mM Ni2+ ions even after 36 h. The highest saccharification yield (SY, 87.4%) was observed with Ni2+ as the contaminant (10 mg/kg dry wt), whereas Pb2+ (251.9 mg/kg dry wt) was the strongest inhibitor of biomass hydrolysis, resulting in only a 30% SY. Importantly, the enzyme cocktail produced by the fungal consortium resulted in almost the same SY (%) as that obtained from a combination of commercial cellulase and β-glucosidase. Significant sugar conversion (61.7%) from H. annuus biomass hydrolysate occurred, resulting in the production of 11.4 g/L of bioethanol. This is the first study to assess the suitability of phytoremediated sunflower biomass for bioethanol production.

Hypoglycemic activity of dried extracts of Bauhinia forficata Link.

Science.gov (United States)

da Cunha, A M; Menon, S; Menon, R; Couto, A G; Bürger, C; Biavatti, M W

2010-01-01

Leaves of the pantropical genus Bauhinia (Fabaceae) are known popularly as cow's foot, due to their unique characteristic bilobed aspect. The species Bauhinia forficata (Brazilian Orchid-tree) is widely used in folk medicine as an antidiabetic. The present work investigates the hypoglycemic activity of the dried extracts of Bauhinia forficata leaves in vivo, as well as the influence of the drying and granulation processes on this activity. The fluid extract was dried to generate oven-dried (ODE), spray-dried (SDE) and wet granulation (WGE) extracts, with the aid of colloidal silicon dioxide and/or cellulose:lactose mixture. The dried extracts were characterized by spectrophotometric, chromatographic and photo microscopy image analysis. 200 mg/kg body wt., p.o. of each dried product were administered orally to male Wistar rats over 7 days old, for biomonitoring of the hypoglycemic activity profile. The effect of the extracts was studied in STZ-induced diabetic rats. After 7 days of treatment, fasting glucose was determined, and the livers were removed, dried on tissue paper, weighed, and stored at -20 degrees C to estimate hepatic glycogen. Our results show that spray-drying or oven-drying processes applied to B. forficata extracts did not significantly alter its flavonoid profile or its hypoglycemic activity. Indeed, the dried extracts of B. forficata act differently from glibenclamide. Despite the lower active content in WGE, because of the higher concentration of adjuvants, the use of the granulation process improved the manufacturing properties of the ODE, making this material more appropriate for use in tablets or capsules.

Intelligent Control Framework for the Feeding System in the Biomass Power Plant

Directory of Open Access Journals (Sweden)

Sun Jin

2015-01-01

Full Text Available This paper proposes an intelligent control framework for biomass drying process with flue gases based on FLC (fuzzy logic controller and CAN (Controller Area Network bus. In the operation of a biomass drying process, in order to get the biomass with the set-point low moisture content dried by waste high temperature flue gases, it is necessary to intelligent control for the biomass flow rate. Use of an experiment with varied materials at different initial moisture contents enables acquisition of the biomass flow rates as initial setting values. Set the error between actual straw moisture content and set-point, and rate of change of error as two inputs. the biomass flow rate can be acquired by the fuzzy logic computing as the output. Since the length of dryer is more than twenty meters, the integration by the CAN bus can ensure real-time reliable data acquisition and processing. The control framework for biomass drying process can be applied to a variety of biomass, such as, cotton stalk, corn stalk, rice straw, wheat straw, sugar cane. It has strong potential for practical applications because of its advantages on intelligent providing the set-point low moisture content of biomass feedstock for power generation equipment.

Analysing biomass torrefaction supply chain costs.

Science.gov (United States)

Svanberg, Martin; Olofsson, Ingemar; Flodén, Jonas; Nordin, Anders

2013-08-01

The objective of the present work was to develop a techno-economic system model to evaluate how logistics and production parameters affect the torrefaction supply chain costs under Swedish conditions. The model consists of four sub-models: (1) supply system, (2) a complete energy and mass balance of drying, torrefaction and densification, (3) investment and operating costs of a green field, stand-alone torrefaction pellet plant, and (4) distribution system to the gate of an end user. The results show that the torrefaction supply chain reaps significant economies of scale up to a plant size of about 150-200 kiloton dry substance per year (ktonDS/year), for which the total supply chain costs accounts to 31.8 euro per megawatt hour based on lower heating value (€/MWhLHV). Important parameters affecting total cost are amount of available biomass, biomass premium, logistics equipment, biomass moisture content, drying technology, torrefaction mass yield and torrefaction plant capital expenditures (CAPEX). Copyright © 2013 Elsevier Ltd. All rights reserved.

Adsorption characteristics of SO{sub 2}, NO by steam activated biomass chars

Energy Technology Data Exchange (ETDEWEB)

Lu, Fei; Shu, Tong; Wang, Kuan; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

2013-07-01

Wheat straw and rice husk collected from the suburb of Nanjing, China, were prepared to different kinds of steam activated biomass-based chars, and the adsorption characteristics of the biomass-based chars was carried out in a fixed bed reactor. The specific surface area and pore structure of different biomass chars were measured by nitrogen adsorption-desorption analysis instrument at 77K. The effects of biomass type, pyrolysis temperature, heating rate, activation temperature and concentration of SO{sub 2}, NO on the adsorption efficiency of SO{sub 2}, NO were analyzed. The results indicated that the steam activation has significant effects on the specific surface area, total pore volume and micro-morphology of biomass chars by improving the internal structure. The adsorption efficiency of SO{sub 2}, NO increased with the decreasing of SO{sub 2}, NO concentration in the experimental range. The optimal condition of char preparation (873K, fast pyrolysis) and steam activation (1,073K) was proposed based on the adsorption efficiency and adsorption volume of SO{sub 2}, NO. It builds a theoretical basis for industrial applications of biomass.

Seasonal and diel variability in dissolved DNA and in microbial biomass and activity in a subtropical estuary

International Nuclear Information System (INIS)

Paul, J.H.; Deflaun, M.F.; Jeffrey, W.H.; David, A.W.

1988-01-01

Dissolved DNA and microbial biomass and activity parameters were measured over a 15-month period at three stations along a salinity gradient in Tampa Bay, Fla. Dissolved DNA showed seasonal variation, with minimal values in December and January and maximal values in summer months (July and August). This pattern of seasonal variation followed that of particulate DNA and water temperature and did not correlate with bacterioplankton (direct counts and [ 3 H] thymidine incorporation) or phytoplankton (chlorophyll α and 14 CO 2 fixation) biomass and activity. Microautotrophic populations showed maxima in the spring and fall, whereas microheterotrophic activity was greatest in late summer (September). Both autotrophic and heterotrophic microbial activity was greatest at the high estuarine (low salinity) station and lowest at the mouth of the bay (high salinity station), irrespective of season. Dissolved DNA carbon and phosphorus constituted 0.11 +/- 0.05% of the dissolved organic carbon and 6.6 +/- 6.5% of the dissolved organic phosphorus, respectively. Strong diel periodicity was noted in dissolved DNA and in microbial activity in Bayboro Harbor during the dry season. A noon maximum in primary productivity was followed by an 8 p.m. maximum in heterotrophic activity and a midnight maximum in dissolved DNA. This diel periodicity was less pronounced in the wet season, when microbial parameters were strongly influenced by episodic inputs of freshwater

Zooplankton biomass data (displacement volume, wet mass, and dry mass) collected by the Sea Fisheries Research Institute (SFRI) in the active upwelling zone on the west coast of South Africa 1969-12-02 to 1969-12-16 (NODC Accession 0071850)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Zooplankton biomass data (displacement volume, wet mass, and dry mass) collected by South African the Sea Fisheries Research Institute (SFRI) during SFRI upwelling...

Novel applications of biomass wet pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Sillanpaa, M. [Lappeenranta Univ. of Technology (Finland)], email: mika.sillanpaa@lut.fi

2012-07-01

Production of carbonaceous material from unconventional wet biomass sources by thermal processing offers interesting novel opportunities and application possibilities in different fields. Thermal treatment at low temperatures refers to torrefication in general. Disadvantage in this technique is that biomass has to be dried first which consumes a lot energy and time and limits use of biomass materials widely. In wetpyrolysis (hydrothermal carbonization, HTC), biomass source can be wetter, like wood, household wastes, manure or industrial wastewater sludge. Reaction takes place in water environment at higher temperature (180-250 deg C) and pressure which is self-generated. Typically reaction system is high pressure reactor also called autoclave. Comparing to torrefaction HTC produces more solid yield, water soluble organic compounds but formation is low during reaction. Properties of the product can be easily modified by changing reaction conditions, utilization of additives or catalysts. Novel materials obtained by this technique will be used in different applications in water treatment and it will be also interesting to compare purification efficiency of these materials to activated carbon.

Method for attaining rosemary essential oil with differential composition from dried or fresh material.

Science.gov (United States)

Zheljazkov, Valtcho D; Astatkie, Tess; Zhalnov, Ivan; Georgieva, Tonya D

2015-01-01

Rosemary (Rosemarinus officinalis L.) is a well-known medicinal and essential oil plant, utilized by humankind since ancient times. The objective was to determine the effect of steam distillation time (DT) and material (dry or fresh biomass) on essential oil yield, composition, and bioactivity; and to develop regression models that can predict oil yield and composition at specific DT. The oil yield (content) from dry biomass was higher (0.43%) than that from fresh biomass (0.35%) and ranged from 0.18% in the 1.25 min DT to 0.51% in the 40 min DT. There was no yield advantage in extending the DT beyond 40 min, which is much shorter than the DT used by industry. In this study, the antioxidant capacity of the rosemary oil using the ORACoil method was 4,108 μmolVE/L. Rosemary oil did not exhibit significant antileishmanial, antimalarial, or antimicrobial activity. In general, the low-boiling constituents eluted earlier than the higher boiling constituents of the essential oil, resulting in a great variation of essential oil composition obtained at different DT. The most important constituents are α-pinene, eucalyptol, and camphor. The highest α-pinene concentration in the oil (30.4%) was obtained from dry biomass at 2.5 min DT; eucalyptol (23.3% of the total oil) from fresh biomass at 2.5 min DT; and camphor (15.9% of the total oil) from fresh biomass at 160 min DT. The DT could be used as an inexpensive tool to alter essential oil composition of the essential oil from fresh or dried rosemary biomass, and to produce rosemary oils with elevated or lowered concentration of specific targeted oil constituents to meet specific market demands.

Costs of Producing Biomass from Riparian Buffer Strips

Energy Technology Data Exchange (ETDEWEB)

Turhollow, A.

2000-09-01

Nutrient runoff from poultry litter applied to agricultural fields in the Delmarva Peninsula contributes to high nutrient loadings in Chesapeake Bay. One potential means of ameliorating this problem is the use of riparian buffer strips. Riparian buffer strips intercept overland flows of water, sediments, nutrients, and pollutants; and ground water flows of nutrients and pollutants. Costs are estimated for three biomass systems grown on buffer strips: willow planted at a density of 15,300 trees/ha (6200 trees/acre); poplar planted at a density of 1345 trees/ha (545 trees/acre); and switchgrass. These costs are estimated for five different scenarios: (1) total economic costs, where everything is costed [cash costs, noncash costs (e.g., depreciation), land rent, labor]; (2) costs with Conservation Reserve Program (CRP) payments (which pays 50% of establishment costs and an annual land rent); (3) costs with enhanced CRP payments (which pays 95% of establishment costs and an annual payment of approximately 170% of land rent for trees and 150% of land rent for grasses); (4) costs when buffer strips are required, but harvest of biomass is not required [costs borne by biomass are for yield enhancing activities (e.g., fertilization), harvest, and transport]; and (5) costs when buffer strips are required. and harvest of biomass is required to remove nutrients (costs borne by biomass are for yield enhancing activities and transport). CRP regulations would have to change to allow harvest. Delivered costs of willow, poplar, and switchgrass [including transportation costs of $0.38/GJ ($0.40/million Btu) for switchgrass and $0.57/GJ ($0.60/million Btu) for willow and poplar] at 11.2 dry Mg/ha-year (5 dry tons/acre-year) for the five cost scenarios listed above are [$/GJ ($million BIN)]: (1) 3.30-5.45 (3.45-5.75); (2) 2.30-3.80 (2.45-4.00); (3) 1.70-2.45 (1.80-2.60); (4) l-85-3.80 (1.95-4.05); and (5) 0.80-1.50 (0.85-1.60). At yields of 15.7 to 17.9 GJ/ha-year (7 to 8 dry tons

Reduction of Biomass Moisture by Crushing/Splitting - A Concept

Science.gov (United States)

Paul E. Barnett; Donald L. Sirois; Colin Ashmore

1986-01-01

A biomass crusher/splitter concept is presented as a possible n&ant of tsafntainfng rights-of-way (ROW) or harvesting energy wood plantations. The conceptual system would cut, crush, and split small woody biomass leaving it in windrows for drying. A subsequent operation would bale and transport the dried material for use as an energy source. A survey of twenty...

Drying characteristics of willow chips and stems

NARCIS (Netherlands)

Gigler, J.K.; Loon, van W.K.P.; Seres, I.; Meerdink, G.; Coumans, W.J.

2000-01-01

In supply chains of willow (Salix viminalis) biomass to energy plants, drying is advisable in order to enable safe long-term storage, increase boiler efficiency and reduce gaseous emissions. To gain insight into the drying process, drying characteristics of willow chips and stems were investigated

Natural convection solar dryer with biomass back-up heater

Energy Technology Data Exchange (ETDEWEB)

Bena, B.; Fuller, R.J. [University of Melbourne (Australia). Faculty of Engineering

2002-07-01

A direct-type natural convection solar dryer and a simple biomass burner have been combined to demonstrate a drying technology suitable for small-scale processors of dried fruits and vegetables in non-electrified areas of developing countries. From a series of evaluation trials of the system, the capacity of the dryer was found to be 20-22kg of fresh pineapple arranged in a single layer of 0.01-m-thick slices. The overall drying efficiency of the unit was calculated to be {approx} 9%. During the same trial, the drying efficiency of the solar component alone was found to be 22%. Other trials estimated the efficiency of the burner in producing useful heat for drying to be 27%. Key features of the biomass burner were found to be the addition of thermal mass on the upper surface, an internal baffle plate to lengthen the exhaust gas exit path and a variable air inlet valve. Further modifications to further improve the performance of both the solar and biomass components of the dryer are suggested. (author)

Current and potential utilisation of biomass energy in Fiji

International Nuclear Information System (INIS)

Prasad, S.

1990-01-01

Energy from biomass accounts for an average of 43% of the primary energy used in developing countries, with some countries totally dependent on biomass for all their energy needs. The most common use for biomass for energy is the provision of heat for cooking and heating; other uses include steam and electricity generation and crop and food drying. Fiji, a developing country, uses energy from wood and coconut wastes for cooking and copra drying. Bagasse from sugar mills is used to generate process steam as well as some 15 MW of electricity, for mill consumption and for sale to the national grid. Other, relatively small scale uses for biomass include the generation of steam and electricity for industry. This paper attempts to quantify the amount of biomass, in its various forms, available in Fiji and assesses the current potential utilisation of biomass for energy in Fiji. (author)

An evaluation of the use of the dry-weight-rank and the comparative yield biomass estimation methods in paramo ecosystem research

Directory of Open Access Journals (Sweden)

Hofstede Robert G.M.

1993-12-01

Full Text Available The use of the combination of the semi-destructive comparative yield method for overall biomass estimation and the non- destructive dry-weight-rank method for studying botanical composition on a dry weight basis in an undisturbed páramo vegetation in the Los Nevados national park (Colombian Central Cordillera was evaluated. These methods, developed for Australian production grasslands, were adapted for use in the páramo ecosystem. The average above ground biomass in the area was estimated as 2864 g dryweight. m-2 (sd.48, of which the bunchgrass Calamagrostis effusa contributed with ca 70%. When used with some adaptations, the comparative yield method seems suitable for biomass estimations in the páramo ecosystem. The here presented estimation of botanical eomposition with this method gave better results than dry-weight-rank method, which had too many shortcomings for use in the complex páramo grassland ecosystem.Se evaluó la aplicabilidad de una combinación de dos étodos para estimar la biomasa  general y la composición botánica, en una vegetación natural paramuna en el Parque Nacional Natural los Nevados (Cordillera Central de Colombia. El primer método (ecomparative yield determina la biomasa general, destruyendo parcialmente la vegetación de los cuadrantes de muestreo y el segundo (dryweight rank determina la composición botánica con base en el peso seco, sin destruir la vegetación. Estos métodos, inicialmente desarrollados para pajonales forrajeros en Australia, se adaptaron para ser utilizados en el ecosistema paramuno. Como resultado se obtuvo una estimación de la biomasa aérea de 2864 g peso seco m2 (desviación stándard 48 en la cual, la gramínea Calamagrostis effusa contribuyó con el 70%. Puede concluirse que el método de producción comparativa es útil para estimar la biomasa en el ecosistema paramuno, siempre y cuando se utilicen las adaptaciones mencionadas. Por otra parte la estimación de la composición bot

Predicting aboveground forest biomass with topographic variables in human-impacted tropical dry forest landscapes

NARCIS (Netherlands)

Salinas-Melgoza, Miguel A.; Skutsch, Margaret; Lovett, Jon C.

2018-01-01

Topographic variables such as slope and elevation partially explain spatial variations in aboveground biomass (AGB) within landscapes. Human activities that impact vegetation, such as cattle grazing and shifting cultivation, often follow topographic features and also play a key role in determining

Developing business in emerging biomass energy markets

International Nuclear Information System (INIS)

Kadyszewski, J.

2005-01-01

Global market trends for forest products were reviewed in this PowerPoint presentation. The status of biomass energy products in relation to climate change and renewable energy portfolio standards was also examined. It was noted that China has increased investment in processing capacity and has increased imports of raw logs. India has doubled its imports of raw logs. Details of major tropical log producers and consumers were presented. Details of the biomass industry in the United States were presented, as well as data on fuel use at biomass energy plants and biomass energy capacity. An overview of biomass energy in the Russian far east and Siberia was presented, as well as details of activities and opportunities in Brazil and Indonesia. An economic analysis for small dry kilns was presented. Issues concerning boiler capacity in Russian companies for 2001-2005 were discussed. A case study of a biomass project from Congo was presented. It was noted that projects that replace fossil fuels can obtain revenues from the sale of carbon benefits, and that biomass energy offers the most attractive current option for the removal of carbon dioxide (CO 2 ) from the atmosphere. Details of a district heating project in Siberia were presented, and it was noted that in remote regions, costs for heat and power from biomass can be lower than costs from diesel and coal. It was concluded that there will be significant growth for biomass energy systems in the developing world, and that climate change will be an increasingly important element in advancing biomass energy. tabs., figs

Seasonal, interannual, and long-term variabilities in biomass burning activity over South Asia.

Science.gov (United States)

Bhardwaj, P; Naja, M; Kumar, R; Chandola, H C

2016-03-01

The seasonal, interannual, and long-term variations in biomass burning activity and related emissions are not well studied over South Asia. In this regard, active fire location retrievals from the Moderate Resolution Imaging Spectroradiometer (MODIS), the retrievals of aerosol optical depth (AOD) from MODIS Terra, and tropospheric column NO2 from Ozone Monitoring Instrument (OMI) are used to understand the effects of biomass burning on the tropospheric pollution loadings over South Asia during 2003-2013. Biomass burning emission estimates from Global Fire Emission Database (GFED) and Global Fire Assimilation System (GFAS) are also used to quantify uncertainties and regional discrepancies in the emissions of carbon monoxide (CO), nitrogen oxide (NOx), and black carbon (BC) due to biomass burning in South Asia. In the Asian continent, the frequency of fire activity is highest over Southeast Asia, followed by South Asia and East Asia. The biomass burning activity in South Asia shows a distinct seasonal cycle that peaks during February-May with some differences among four (north, central, northeast, and south) regions in India. The annual biomass burning activity in north, central, and south regions shows an increasing tendency, particularly after 2008, while a decrease is seen in northeast region during 2003-2013. The increase in fire counts over the north and central regions contributes 24 % of the net enhancement in fire counts over South Asia. MODIS AOD and OMI tropospheric column NO2 retrievals are classified into high and low fire activity periods and show that biomass burning leads to significant enhancement in tropospheric pollution loading over both the cropland and forest regions. The enhancement is much higher (110-176 %) over the forest region compared to the cropland (34-62 %) region. Further efforts are required to understand the implications of biomass burning on the regional air quality and climate of South Asia.

Dry season aerosol iron solubility in tropical northern Australia

Directory of Open Access Journals (Sweden)

V. H. L. Winton

2016-10-01

Full Text Available Marine nitrogen fixation is co-limited by the supply of iron (Fe and phosphorus in large regions of the global ocean. The deposition of soluble aerosol Fe can initiate nitrogen fixation and trigger toxic algal blooms in nitrate-poor tropical waters. We present dry season soluble Fe data from the Savannah Fires in the Early Dry Season (SAFIRED campaign in northern Australia that reflects coincident dust and biomass burning sources of soluble aerosol Fe. The mean soluble and total aerosol Fe concentrations were 40 and 500 ng m−3 respectively. Our results show that while biomass burning species may not be a direct source of soluble Fe, biomass burning may substantially enhance the solubility of mineral dust. We observed fractional Fe solubility up to 12 % in mixed aerosols. Thus, Fe in dust may be more soluble in the tropics compared to higher latitudes due to higher concentrations of biomass-burning-derived reactive organic species in the atmosphere. In addition, biomass-burning-derived particles can act as a surface for aerosol Fe to bind during atmospheric transport and subsequently be released to the ocean upon deposition. As the aerosol loading is dominated by biomass burning emissions over the tropical waters in the dry season, additions of biomass-burning-derived soluble Fe could have harmful consequences for initiating nitrogen-fixing toxic algal blooms. Future research is required to quantify biomass-burning-derived particle sources of soluble Fe over tropical waters.

ENDOGENOUS CYTOKININS IN MEDICINAL BASIDIOMYCETES MYCELIAL BIOMASS

Directory of Open Access Journals (Sweden)

N. P.

2016-02-01

Full Text Available The aim of the research was to study the cytokinins production by medicinal basidial mushrooms. Cytokinins were for the first time identified and quantified in mycelial biomass of six species (Ganoderma lucidum, Trametes versicolor, Fomitopsis officinalis, Pleurotus nebrodensis, Grifola frondosa, Sparassis crispa using HPLC. Trans- and cis-zeatin, zeatin riboside, zeatin-O-glucoside, isopentenyladenosine, isopentenyladenine were found but only one species (G. lucidum, strain 1900 contained all these substances. The greatest total cytokinin quantity was detected in F. officinalis, strain 5004. S. crispa, strain 314, and F. officinalis, strain 5004, mycelial biomass was revealed to have the highest level of cytokinin riboside forms (zeatin riboside and isopentenyladenosine. The possible connection between medicinal properties of investigated basidiomycetes and of cytokinins is discussed. S. crispa, strain 314, and F. officinalis, strain 5004, are regarded as promising species for developing biotechnological techniques to produce biologically active drugs from their mycelial biomass. As one of the potential technological approaches there is proposed fungal material drying.

Biosorption of uranium by cross-linked and alginate immobilized residual biomass from distillery spent wash

International Nuclear Information System (INIS)

Bustard, M.; McHale, A.P.

1997-01-01

Residual biomass from a whiskey distillery was examined for its ability to function as a biosorbent for uranium. Biomass recovered and lyophilised exhibited a maximum biosorption capacity of 165-170 mg uranium/g dry weight biomass at 15 C. With a view towards the development of continuous or semi-continuous flow biosorption processes it was decided to immobilize the material by (1) cross-linking with formaldehyde and (2) introducing that material into alginate matrices. Cross-linking the recovered biomass resulted in the formation of a biosorbent preparation with a maximum biosorption capacity of 185-190 mg/g dry weight biomass at 15 C. Following immobilization of biomass in alginate matrices it was found that the total amount of uranium bound to the matrix did not change with increasing amounts of biomass immobilized. It was found however, that the proportion of uranium bound to the biomass within the alginate-biomass matrix increased with increasing biomass concentration. Further analysis of these preparations demonstrated that the alginate-biomass matrix had a maximum biosorption capacity of 220 mg uranium/g dry weight of the matrix, even at low concentrations of biomass. (orig.). With 3 figs., 1 tab

Biosorption of uranium by cross-linked and alginate immobilized residual biomass from distillery spent wash

Energy Technology Data Exchange (ETDEWEB)

Bustard, M. [Biotechnology Research Group, School of Applied Biological and Chemical Sciences, University of Ulster, Coleraine (United Kingdom); McHale, A.P. [Biotechnology Research Group, School of Applied Biological and Chemical Sciences, University of Ulster, Coleraine (United Kingdom)

1997-08-01

Residual biomass from a whiskey distillery was examined for its ability to function as a biosorbent for uranium. Biomass recovered and lyophilised exhibited a maximum biosorption capacity of 165-170 mg uranium/g dry weight biomass at 15 C. With a view towards the development of continuous or semi-continuous flow biosorption processes it was decided to immobilize the material by (1) cross-linking with formaldehyde and (2) introducing that material into alginate matrices. Cross-linking the recovered biomass resulted in the formation of a biosorbent preparation with a maximum biosorption capacity of 185-190 mg/g dry weight biomass at 15 C. Following immobilization of biomass in alginate matrices it was found that the total amount of uranium bound to the matrix did not change with increasing amounts of biomass immobilized. It was found however, that the proportion of uranium bound to the biomass within the alginate-biomass matrix increased with increasing biomass concentration. Further analysis of these preparations demonstrated that the alginate-biomass matrix had a maximum biosorption capacity of 220 mg uranium/g dry weight of the matrix, even at low concentrations of biomass. (orig.). With 3 figs., 1 tab.

Preparation of activated Carbons from extracted waste biomass by chemical activation

International Nuclear Information System (INIS)

Toteva, V.; Nickolov, R.

2013-01-01

Full text: Novel biomass precursors for the production of activated carbons (ACs) were studied. ACs were prepared from extracted coffee husks and extracted spent ground coffee - separately or as mixtures with 10, 20 and 30 mass % Bulgarian lignite coal. Activation by potassium hydroxide was employed for all samples. The results obtained show that the surface and porous parameters of the ACs depend on the nature of the initial materials used. The specific surface areas (BET) and the microporosities of ACs obtained from extracted spent ground coffee mixed with 20 mass % Bulgarian lignite coals, are greater than those of the ACs from extracted coffee husks. It is likely that the reason for this result is the chemical composition of the precursors. The coffee husks have less lignin and more holocellulose. The latter undergoes more significant destructive changes in the process of chemical activation. On the contrary, waste ground coffee precursors contain more lignin and less holocellulose. As a result, after the chemical activation, the carbons prepared from extracted spent ground coffee exhibit better porous parameters and higher specific surface areas. key words: activated carbons, extraction, waste biomass

A study of palm biomass processing strategy in Sarawak

Science.gov (United States)

Lee, S. J. Y.; Ng, W. P. Q.; Law, K. H.

2017-06-01

In the past decades, palm industry is booming due to its profitable nature. An environmental concern regarding on the palm industry is the enormous amount of waste produced from palm industry. The waste produced or palm biomass is one significant renewable energy source and raw material for value-added products like fiber mats, activated carbon, dried fiber, bio-fertilizer and et cetera in Malaysia. There is a need to establish the palm biomass industry for the recovery of palm biomass for efficient utilization and waste reduction. The development of the industry is strongly depending on the two reasons, the availability and supply consistency of palm biomass as well as the availability of palm biomass processing facilities. In Malaysia, the development of palm biomass industry is lagging due to the lack of mature commercial technology and difficult logistic planning as a result of scattered locality of palm oil mill, where palm biomass is generated. Two main studies have been carried out in this research work: i) industrial study of the feasibility of decentralized and centralized palm biomass processing in Sarawak and ii) development of a systematic and optimized palm biomass processing planning for the development of palm biomass industry in Sarawak, Malaysia. Mathematical optimization technique is used in this work to model the above case scenario for biomass processing to achieve maximum economic potential and resource feasibility. An industrial study of palm biomass processing strategy in Sarawak has been carried out to evaluate the optimality of centralized processing and decentralize processing of the local biomass industry. An optimal biomass processing strategy is achieved.

Microbial biomass carbon and enzyme activities of urban soils in Beijing.

Science.gov (United States)

Wang, Meie; Markert, Bernd; Shen, Wenming; Chen, Weiping; Peng, Chi; Ouyang, Zhiyun

2011-07-01

To promote rational and sustainable use of soil resources and to maintain the urban soil quality, it is essential to assess urban ecosystem health. In this study, the microbiological properties of urban soils in Beijing and their spatial distribution patterns across the city were evaluated based on measurements of microbial biomass carbon and urease and invertase activities of the soils for the purpose of assessing the urban ecosystem health of Beijing. Grid sampling design, normal Kriging technique, and the multiple comparisons among different land use types were used in soil sampling and data treatment. The inherent chemical characteristics of urban soils in Beijing, e.g., soil pH, electronic conductivity, heavy metal contents, total N, P and K contents, and soil organic matter contents were detected. The size and diversity of microbial community and the extent of microbial activity in Beijing urban soils were measured as the microbial biomass carbon content and the ratio of microbial biomass carbon content to total soil organic carbon. The microbial community health measured in terms of microbial biomass carbon, urease, and invertase activities varied with the organic substrate and nutrient contents of the soils and were not adversely affected by the presence of heavy metals at p urban soils influenced the nature and activities of the microbial communities.

[Effects of bio-crust on soil microbial biomass and enzyme activities in copper mine tailings].

Science.gov (United States)

Chen, Zheng; Yang, Gui-de; Sun, Qing-ye

2009-09-01

Bio-crust is the initial stage of natural primary succession in copper mine tailings. With the Yangshanchong and Tongguanshan copper mine tailings in Tongling City of Anhui Province as test objects, this paper studied the soil microbial biomass C and N and the activities of dehydrogenase, catalase, alkaline phosphatase, and urease under different types of bio-crust. The bio-crusts improved the soil microbial biomass and enzyme activities in the upper layer of the tailings markedly. Algal crust had the best effect in improving soil microbial biomass C and N, followed by moss-algal crust, and moss crust. Soil microflora also varied with the type of bio-crust. No'significant difference was observed in the soil enzyme activities under the three types of bio-crust. Soil alkaline phosphatase activity was significantly positively correlated with soil microbial biomass and dehydrogenase and urease activities, but negatively correlated with soil pH. In addition, moss rhizoid could markedly enhance the soil microbial biomass and enzyme activities in moss crust rhizoid.

Arrhenius activation energy of damage to catalase during spray-drying.

Science.gov (United States)

Schaefer, Joachim; Lee, Geoffrey

2015-07-15

The inactivation of catalase during spray-drying over a range of outlet gas temperatures could be closely represented by the Arrhenius equation. From this an activation energy for damage to the catalase could be calculated. The close fit to Arrhenius suggests that the thermally-induced part of inactivation of the catalase during the complex drying and particle-formation processes takes place at constant temperature. These processes are rapid compared with the residence time of the powder in the collecting vessel of the cyclone where dried catalase is exposed to a constant temperature equal to approximately the drying gas outlet temperature. A lower activation energy after spray drying with the ultrasonic nozzle was found than with the 2-fluid nozzle under otherwise identical spray drying conditions. It is feasible that the ultrasonic nozzle when mounted in the lid of the spray dryer heats up toward the drying gas inlet temperature much more that the air-cooled 2-fluid nozzle. Calculation of the Arrhenius activation energy also showed how the stabilizing efficacy of trehalose and mannitol on the catalase varies in strength across the range of drying gas inlet and outlet temperatures examined. Copyright © 2015 Elsevier B.V. All rights reserved.

BIOMASS AND MICROBIAL ACTIVITY UNDER DIFFERENT FOREST COVERS

Directory of Open Access Journals (Sweden)

Rafael Malfitano Braga

2016-06-01

Full Text Available This study evaluated the soil fertility, biomass and microbial activity of the soil under forest cover of Eucalyptus grandis, Eucalyptus pilularis, Eucalyptus cloeziana and Corymbia maculata; Pinus Caribbean var. hondurensis, 40 years old, and a fragment of Semideciduous Forest, located on the campus of the Federal University of Lavras. In soil samples collected in the 0-5 cm layer were determined fertility parameters, basal respiration and microbial biomass carbon. The results showed that for the species E. grandis and E. cloeziana the carbon of biomass microbial content was higher than for any other ecosystem evaluated, and equal to those observed under native forest. In contrast, the ground under Pinus had the lowest microbiological indexes. Under C. maculata and E. pilularis the contents were intermediate for this parameter. The basal respiration of all ecosystems was equal. The fertility level was very low in all types of evaluated vegetation.

Effects of simulated acid rain on the morphology, phenology and dry biomass of a local variety of maize (Suwan-1) in Southwestern Nigeria.

Science.gov (United States)

Macaulay, Babajide Milton; Enahoro, Gloria Ebarunosen

2015-10-01

Effects of acid rain on the morphology, phenology and dry biomass of maize (Suwan-1 variety) were investigated. The maize seedlings were subjected to different pH treatments (1.0, 2.0, 3.0, 4.0, 5.0 and 6.0) of simulated acid rain (SAR) with pH 7.0 as the control for a period of 90 days. The common morphological defects due to SAR application were necrosis and chlorosis. It was observed that necrosis increased in severity as the acidity increased whilst chlorosis was dominant as the acidity decreased. SAR encouraged rapid floral and cob growth but with the consequence of poor floral and cob development in pH 1.0 to 3.0 treatments. The result for the dry biomass indicates that pH treatments 2.0 to 7.0 for total plant biomass were not significantly different (P > 0.05) from one another, but were all significantly higher (P pH 1.0. Therefore, it may be deduced that Suwan-1 has the potential to withstand acid rain but with pronounced morphological and phenological defects which, however, have the capacity to reduce drastically the market value of the crop. Therefore, it may be concluded that Suwan-1 tolerated acid rain in terms of the parameters studied at pH 4.0 to 7.0 which makes it a suitable crop in acid rain-stricken climes. This research could also serve as a good reference for further SAR studies on maize or other important cereals.

Biomass Development in SRI Field Under Unmaintained Alternate Wetting-Drying Irrigation

Science.gov (United States)

Ardiansyah; Chusnul, A.; Krissandi, W.; Asna, M.

2018-05-01

The aim of this research is to observe biomass development of SRI on farmers practice in three plots with different level. This research observes the farmer practice of SRI and Non-SRI during the uncertainty of irrigation water supply and its effects on paddy biomass development during growth stages and final stage of crop. A farmer group that already understand the principle of SRI, applied this method into several plots of their rented paddy field. Researcher interventions were eliminated from their action, so it is purely on farmers decision on managing their SRI plots. Three plots from both SRI and Non-SRI were chosen based on the position of the plot related their access to water. First plots had direct access to water from tertiary irrigation channel (on farm). Second plots were received water from previous upper plots and drainage water into other plots. Third plots were in the bottom position, where they received water from upper plot, and drainage water into farm drainage channel. Result shows there are similar patterns of root, straw, and leaves of biomass during crop growth. On the other hand, during generative phase, grain development shows different pattern and resulting different biomass in harvest time. Second plot, (of SRI) that has water from first plot has the average of biomass grain per plant of 54.4, higher than first plot and third plot, which are 33.8 g and 38.4. Average biomass in second plot is 74.6 g, higher than first and third plot, which are 49.9 g and 52.3 g.

Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

Science.gov (United States)

Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

2012-11-01

The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

A tree biomass and carbon estimation system

Science.gov (United States)

Emily B. Schultz; Thomas G. Matney; Donald L. Grebner

2013-01-01

Appropriate forest management decisions for the developing woody biofuel and carbon credit markets require inventory and growth-and-yield systems reporting component tree dry weight biomass estimates. We have developed an integrated growth-and-yield and biomass/carbon calculator. The objective was to provide Mississippi’s State inventory system with bioenergy economic...

Is torrefaction of polysaccharides-rich biomass equivalent to carbonization of lignin-rich biomass?

Science.gov (United States)

Bilgic, E; Yaman, S; Haykiri-Acma, H; Kucukbayrak, S

2016-01-01

Waste biomass species such as lignin-rich hazelnut shell (HS) and polysaccharides-rich sunflower seed shell (SSS) were subjected to torrefaction at 300°C and carbonization at 600°C under nitrogen. The structural variations in torrefied and carbonized biomasses were compared. Also, the burning characteristics under dry air and pure oxygen (oxy-combustion) conditions were investigated. It was concluded that the effects of carbonization on HS are almost comparable with the effects of torrefaction on SSS in terms of devolatilization and deoxygenation potentials and the increases in carbon content and the heating value. Consequently, it can be proposed that torrefaction does not provide efficient devolatilization from the lignin-rich biomass while it is relatively more efficient for polysaccharides-rich biomass. Heat-induced variations in biomass led to significant changes in the burning characteristics under both burning conditions. That is, low temperature reactivity of biomass reduced considerably and the burning shifted to higher temperatures with very high burning rates. Copyright © 2015 Elsevier Ltd. All rights reserved.

Designing CAF-adjuvanted dry powder vaccines: Spray drying preserves the adjuvant activity of CAF01

DEFF Research Database (Denmark)

Ingvarsson, Pall Thor; Schmidt, Signe Tandrup; Christensen, Dennis

2013-01-01

spray drying. The optimal excipient to stabilize CAF01 during spray drying and for the design of nanocomposite microparticles was identified among mannitol, lactose and trehalose. Trehalose and lactose were promising stabilizers with respect to preserving liposome size, as compared to mannitol...... parameters suggested that a fast drying rate is essential to avoid phase separation and lipid accumulation at the surface of the microparticles during spray drying. Finally, immunization studies in mice with CAF01 in combination with the tuberculosis antigen Ag85B-ESAT6-Rv2660c (H56) demonstrated that spray...... drying of CAF01 with trehalose under optimal processing conditions resulted in the preservation of the adjuvant activity in vivo. These data demonstrate the importance of liposome stabilization via optimization of formulation and processing conditions in the engineering of dry powder liposome...

Effects of oxytetracycline, tylosin, and amoxicillin antibiotics on specific methanogenic activity of anaerobic biomass

OpenAIRE

Mohammad Mehdi Amin; Hassan Hashemi; Afshin Ebrahimi; Asghar Ebrahimi

2012-01-01

Aims: The purpose of this study was to survey the antibiotics effects of oxytetracycline, tylosin, and amoxicillin on anerobic wastewater treatment process. Materials and Methods: To evaluate the inhibitory antibiotics amoxicillin, tetracycline, and tylosin on biomass activity, specific methanogenic activity (SMA) using anerobic biomass batch; into 120 ml vials: 30 ml biomass and 70 ml substrate including volatile fatty acids, mainly acetic acid and various concentrations of antibiotics we...

The determination of mercury content in the biomass untended for industrial power plant

Directory of Open Access Journals (Sweden)

Wiktor Magdalena

2017-01-01

Full Text Available Biomass is one of the oldest and most widely used renewable energy sources. The biomass is the whole organic matter of vegetable or animal origin which is biodegradable. Biomass includes leftovers from agricultural production, forestry residues, and industrial and municipal waste. The use of biomass in the power industry has become a standard and takes place in Poland and other European countries. This paper discusses the correlation of mercury content in different biomass types used in the power industry and in products of biomass combustion. Different biomass types, which are currently burned in a commercial power plant in Poland, were discussed. A photographic documentation of different biomass types, such as straw briquettes, wood briquettes, pellets from energy crops (sunflower husk and wood husk, wood pellets, wood chips, and agro-biomass (seeds was carried out. The presented paper discusses the results obtained for 15 biomass samples. Five selected biomass samples were burned in controlled conditions in the laboratory at the University of Silesia. The ash resulting from the combustion of five biomass samples was tested for mercury content. A total of twenty biomass samples and its combustion products were tested. Based on the obtained results, it was found that any supply of biomass, regardless of its type, is characterized by variable mercury content in dry matter. In the case of e.g. wood chips, the spread of results reaches 235.1 μm/kg (in dry matter. Meanwhile, the highest mercury content, 472.4 μm/kg (in dry matter was recorded in the biomass of straw, wood pellets, and pellets from energy crops (sunflower husk. In the case of combustion products of five selected biomass types, a three or four fold increase in the mercury content has been observed.

Comparison between freeze and spray drying to obtain powder Rubrivivax gelatinosus biomass Comparação entre a secagem por liofilização e atomização para produção de biomassa bacteriana

Directory of Open Access Journals (Sweden)

Edson Francisco do Espírito Santo

2013-03-01

Full Text Available The use of colorants in products of animal origin is justified by the improvement in the color of foods since this attribute is considered a quality criterion. These additives can be produced using industrial effluents as substrates and appropriate organisms, such as Rubrivivax gelatinosus. Oxycarotenoids represent a class of carotenes responsible for the pigmentation of animals and vegetables. R. gelatinosus grows in fish industry effluent with the resulting production of a bacterial biomass containing oxycarotenoids. The purpose of this study was to compare the use of two drying processes - spray and freeze drying - to obtain powder biomass in terms of the process parameters (yield, productivity, and product recovery and the product characteristics (color, proximate composition, and oxycarotenoids. No difference was detected in the yield between these techniques, while productivity was higher using spray drying. Higher product recovery and moisture were achieved with freeze drying, while ash was higher with spray drying. The freeze dried biomass was redder, darker and less saturated than the spray dried biomass. No difference in oxycarotenoids was detected between the biomasses. Although it results in lower recovery rate, spray drying was faster and more productive, and it provided the same yield as freeze drying, which makes it the method of choice for obtaining R. gelatinosus biomass.O uso de corantes em produtos de origem animal justifica-se pela melhora na cor dos alimentos, uma vez que este atributo é considerado um critério de qualidade. Estes aditivos podem ser produzidos utilizando efluentes industriais como substratos e organismos adequados, como Rubrivivax gelatinosus. Oxicarotenóides representam uma classe de carotenos, responsáveis pela coloração de animais e vegetais. R. gelatinosus cresce em efluente de indústria de pescado produzindo biomassa contendo oxicarotenóides. O objetivo deste experimento foi comparar duas

Relationship among Phosphorus Circulation Activity, Bacterial Biomass, pH, and Mineral Concentration in Agricultural Soil

Directory of Open Access Journals (Sweden)

Dinesh Adhikari

2017-12-01

Full Text Available Improvement of phosphorus circulation in the soil is necessary to enhance phosphorus availability to plants. Phosphorus circulation activity is an index of soil’s ability to supply soluble phosphorus from organic phosphorus in the soil solution. To understand the relationship among phosphorus circulation activity; bacterial biomass; pH; and Fe, Al, and Ca concentrations (described as mineral concentration in this paper in agricultural soil, 232 soil samples from various agricultural fields were collected and analyzed. A weak relationship between phosphorus circulation activity and bacterial biomass was observed in all soil samples (R2 = 0.25, and this relationship became significantly stronger at near-neutral pH (6.0–7.3; R2 = 0.67. No relationship between phosphorus circulation activity and bacterial biomass was observed at acidic (pH < 6.0 or alkaline (pH > 7.3 pH. A negative correlation between Fe and Al concentrations and phosphorus circulation activity was observed at acidic pH (R2 = 0.72 and 0.73, respectively, as well as for Ca at alkaline pH (R2 = 0.64. Therefore, bacterial biomass, pH, and mineral concentration should be considered together for activation of phosphorus circulation activity in the soil. A relationship model was proposed based on the effects of bacterial biomass and mineral concentration on phosphorus circulation activity. The suitable conditions of bacterial biomass, pH, and mineral concentration for phosphorus circulation activity could be estimated from the relationship model.

Enzymatic Hydrolysis of biomasses having a high dry matter (DM) content

DEFF Research Database (Denmark)

2010-01-01

that the biomasses are subjected to mechanical forces, primarily shear and tear forces. Furthermore, the present invention relates to the further utilization of such processed biomasses, e.g. for subsequent fermentation into bio-ethanol, bio-gas, specialty carbohydrates for food and fees as well as carbon feedstock...... for processing into plastics and chemicals....

Biomass resources in California

Energy Technology Data Exchange (ETDEWEB)

Tiangco, V.M.; Sethi, P.S. [California Energy Commission, Sacramento, CA (United States)

1993-12-31

The biomass resources in California which have potential for energy conversion were assessed and characterized through the project funded by the California Energy Commission and the US Department of Energy`s Western Regional Biomass Energy Program (WRBEP). The results indicate that there is an abundance of biomass resources as yet untouched by the industry due to technical, economic, and environmental problems, and other barriers. These biomass resources include residues from field and seed crops, fruit and nut crops, vegetable crops, and nursery crops; food processing wastes; forest slash; energy crops; lumber mill waste; urban wood waste; urban yard waste; livestock manure; and chaparral. The estimated total potential of these biomass resource is approximately 47 million bone dry tons (BDT), which is equivalent to 780 billion MJ (740 trillion Btu). About 7 million BDT (132 billion MJ or 124 trillion Btu) of biomass residue was used for generating electricity by 66 direct combustion facilities with gross capacity of about 800 MW. This tonnage accounts for only about 15% of the total biomass resource potential identified in this study. The barriers interfering with the biomass utilization both in the on-site harvesting, collection, storage, handling, transportation, and conversion to energy are identified. The question whether these barriers present significant impact to biomass {open_quotes}availability{close_quotes} and {open_quotes}sustainability{close_quotes} remains to be answered.

Integration of alternative feedstreams for biomass treatment and utilization

Science.gov (United States)

Hennessey, Susan Marie [Avondale, PA; Friend, Julie [Claymont, DE; Dunson, Jr., James B.; Tucker, III, Melvin P.; Elander, Richard T [Evergreen, CO; Hames, Bonnie [Westminster, CO

2011-03-22

The present invention provides a method for treating biomass composed of integrated feedstocks to produce fermentable sugars. One aspect of the methods described herein includes a pretreatment step wherein biomass is integrated with an alternative feedstream and the resulting integrated feedstock, at relatively high concentrations, is treated with a low concentration of ammonia relative to the dry weight of biomass. In another aspect, a high solids concentration of pretreated biomass is integrated with an alternative feedstream for saccharifiaction.

Immobilized acclimated biomass-powdered activated carbon for the bioregeneration of granular activated carbon loaded with phenol and o-cresol.

Science.gov (United States)

Toh, Run-Hong; Lim, Poh-Eng; Seng, Chye-Eng; Adnan, Rohana

2013-09-01

The objectives of the study are to use immobilized acclimated biomass and immobilized biomass-powdered activated carbon (PAC) as a novel approach in the bioregeneration of granular activated carbon (GAC) loaded with phenol and o-cresol, respectively, and to compare the efficiency and rate of the bioregeneration of the phenolic compound-loaded GAC using immobilized and suspended biomasses under varying GAC dosages. Bioregeneration of GAC loaded with phenol and o-cresol, respectively, was conducted in batch system using the sequential adsorption and biodegradation approach. The results showed that the bioregeneration efficiency of GAC loaded with phenol or o-cresol was basically the same irrespective of whether the immobilized or suspended biomass was used. Nonetheless, the duration for bioregeneration was longer under immobilized biomass. The beneficial effect of immobilized PAC-biomass for bioregeneration is the enhancement of the removal rate of the phenolic compounds via adsorption and the shortening of the bioregeneration duration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Steam pretreatment of dry and ensiled industrial hemp for ethanol production

Energy Technology Data Exchange (ETDEWEB)

Sipos, Balint; Reczey, Kati [Budapest University of Technology and Economics, Department of Applied Biotechnology and Food Science, Szt. Gellert ter 4., H-1111 Budapest (Hungary); Kreuger, Emma; Bjoernsson, Lovisa [Lund University, Department of Biotechnology, P.O. Box 124, SE-221 00 Lund (Sweden); Svensson, Sven-Erik [Swedish University of Agricultural Sciences, Department of Agriculture - Farming Systems, Technology and Product Quality, P.O. Box 104, SE-230 53 Alnarp (Sweden); Zacchi, Guido [Lund University, Department of Chemical Engineering, P.O. Box 124, SE-221 00 Lund (Sweden)

2010-12-15

Biomass can be converted into liquid and gaseous biofuels with good efficiency. In this study, the conversion of industrial hemp (Cannabis sativa L.), a biomass source that can be cultivated with a high biomass yield per hectare, was used. Steam pretreatment of dry and ensiled hemp was investigated prior to ethanol production. The pretreatment efficiency was evaluated in terms of sugar recovery and polysaccharide conversion in the enzymatic hydrolysis step. For both materials, impregnation with 2% SO{sub 2} followed by steam pretreatment at 210 C for 5 min were found to be the optimal conditions leading to the highest overall yield of glucose. Simultaneous saccharification and fermentation experiments carried out with optimised pretreatment conditions resulted in ethanol yields of 163 g kg{sup -1} ensiled hemp (dry matter) (71% of the theoretical maximum) and 171 g kg{sup -1} dry hemp (74%), which corresponds to 206-216 l Mg{sup -1} ethanol based on initial dry material. (author)

A spatial model for the economic evaluation of biomass production systems

International Nuclear Information System (INIS)

Wei Liu; Phillips, V.D.; Singh, Devindar

1992-01-01

A system model for estimating short-rotation, intensive-culture woody biomass production costs, including establishment, maintenance, harvesting, and transport costs, was developed and applied to the island of Kauai. Using data from existing large-plot field trials, biomass yield of the tropical hardwood Eucalyptus saligna was predicted from site-specific factors such as local weather and soil conditions and management strategies. Possible harvesting systems were identified and associated harvesting costs were estimated. The distances from the plantation sites to a bio-conversion plant located at the Lihue sugar mill were calculated based on existing road networks. The delivered cost of biomass on a dollar per dry metric ton (Mg) basis was then calculated using a discounted cash flow method. A geographic information system was interfaced with the biomass system model to access a database and present results in map form. Under the most favorable management strategy modeled, approximately 330 x 10 3 dry Mg year -1 of Eucalyptus saligna could be produced from 12,000 ha at a delivered cost of $25-38 per dry Mg chips. (author)

Effect of balanced low pressure drying of curcuma longa leaf on skin immune activation activities.

Science.gov (United States)

Choi, Wooseok; Lim, Hye Won; Lee, Hyeon Yong

2014-01-01

The effect of balanced low pressure drying pretreatment associated with ultrasonication extraction (BU) on the enhancement of skin immune modulatory activities of Curcuma longa leaf was studied by comparing with conventional hot air drying (HE), freeze drying (FE) and balanced low pressure drying (BE) pretreatment processes. In considering skin immune activation activities such as the inhibition of hyaluronidase activity, the BU extract showed ca. 10% higher than those of HE, and even higher than that of the FE extract. Nitric oxide production from macrophage of the BU extract in adding 1.0 mg/mL was increased up to 16.5 μM. When measuring inhibition of IL-6 and TNF-a production from the human T lymphocytes (T cell), the BU extract also showed 53% and 78% of inhibition effect, respectively. It is found that the BU extract could effectively suppress the expression levels of skin inflammation related genes such as Cox-2 and iNOS, down to 80% and 85% compared to the control, respectively. Balanced low pressure drying process was especially active on dehydration of the leaves with minimizing the destruction and making easier elution of the bioactive substances, which resulted in higher extraction yield and better biological activities.

Distributions of trace gases and aerosols during the dry biomass burning season in southern Africa

Science.gov (United States)

Sinha, Parikhit; Hobbs, Peter V.; Yokelson, Robert J.; Blake, Donald R.; Gao, Song; Kirchstetter, Thomas W.

2003-09-01

Vertical profiles in the lower troposphere of temperature, relative humidity, sulfur dioxide (SO2), ozone (O3), condensation nuclei (CN), and carbon monoxide (CO), and horizontal distributions of twenty gaseous and particulate species, are presented for five regions of southern Africa during the dry biomass burning season of 2000. The regions are the semiarid savannas of northeast South Africa and northern Botswana, the savanna-forest mosaic of coastal Mozambique, the humid savanna of southern Zambia, and the desert of western Namibia. The highest average concentrations of carbon dioxide (CO2), CO, methane (CH4), O3, black particulate carbon, and total particulate carbon were in the Botswana and Zambia sectors (388 and 392 ppmv, 369 and 453 ppbv, 1753 and 1758 ppbv, 79 and 88 ppbv, 2.6 and 5.5 μg m-3, and 13.2 and 14.3 μg m-3). This was due to intense biomass burning in Zambia and surrounding regions. The South Africa sector had the highest average concentrations of SO2, sulfate particles, and CN (5.1 ppbv, 8.3 μg m-3, and 6400 cm-3, respectively), which derived from biomass burning and electric generation plants and mining operations within this sector. Air quality in the Mozambique sector was similar to the neighboring South Africa sector. Over the arid Namibia sector there were polluted layers aloft, in which average SO2, O3, and CO mixing ratios (1.2 ppbv, 76 ppbv, and 310 ppbv, respectively) were similar to those measured over the other more polluted sectors. This was due to transport of biomass smoke from regions of widespread savanna burning in southern Angola. Average concentrations over all sectors of CO2 (386 ± 8 ppmv), CO (261 ± 81 ppbv), SO2 (2.5 ± 1.6 ppbv), O3 (64 ± 13 ppbv), black particulate carbon (2.3 ± 1.9 μg m-3), organic particulate carbon (6.2 ± 5.2 μg m-3), total particle mass (26.0 ± 4.7 μg m-3), and potassium particles (0.4 ± 0.1 μg m-3) were comparable to those in polluted, urban air. Since the majority of the measurements

Recent Biomass Burning in the Tropics and Related Changes in Tropospheric Ozone

Science.gov (United States)

Ziemke; Chandra, J. R. S.; Duncan, B. N.; Schoeberl, M. R.; Torres, O.; Damon, M. R.; Bhartia, P. K.

2009-01-01

Biomass burning is an important source of chemical precursors of tropospheric ozone. In the tropics, biomass burning produces ozone enhancements over broad regions of Indonesia, Africa, and South America including Brazil. Fires are intentionally set in these regions during the dry season each year to clear cropland and to clear land for human/industrial expansion. In Indonesia enhanced burning occurs during dry El Nino conditions such as in 1997 and 2006. These burning activities cause enhancement in atmospheric particulates and trace gases which are harmful to human health. Measurements from the Aura Ozone Monitoring Instrument (OMI) and Microwave Limb Sounder (MLS) from October 2004-November 2008 are used to evaluate the effects of biomass burning on tropical tropospheric ozone. These measurements show sizeable decreases approx.15-20% in ozone in Brazil during 2008 compared to 2007 which we attribute to the reduction in biomass burning. Three broad biomass burning regions in the tropics (South America including Brazil, western Africa, and Indonesia) were analyzed in the context of OMI/MLS measurements and the Global Modeling Initiative (GMI) chemical transport model developed at Goddard Space Flight Center. The results indicate that the impact of biomass burning on ozone is significant within and near the burning regions with increases of approx.10-25% in tropospheric column ozone relative to average background concentrations. The model suggests that about half of the increases in ozone from these burning events come from altitudes below 3 km. Globally the model indicates increases of approx.4-5% in ozone, approx.7-9% in NO, (NO+NO2), and approx.30-40% in CO.

Performance of dead Azolla filiculoides biomass in Biosorption of Au from wastewater.

Science.gov (United States)

Umali, L J; Duncan, J R; Burgess, J E

2006-01-01

Dried milled biomass of Azolla filiculoides removed up to 98.2% of gold from wastewater from a gold plating factory containing 5 mg gold/l in solution in batch biosorption. The gold uptake capacity of the biomass was 98 mg/g. Whole dried biomass used in a continuous flow column removed up to 100% of gold from diluted wastewater. A similar column was linked to a sulphide precipitation process to provide a two-step system which was able to remove 98% of gold from undiluted wastewater containing 41 mg Au/l. The lifetime of the column was five days.

BOREAS RSS-15 SIR-C and Landsat TM Biomass and Landcover Maps of the NSA

Science.gov (United States)

Hall, Forrest G. (Editor); Nickeson, Jaime (Editor); Ranson, K. Jon

2000-01-01

As part of BOREAS, the RSS-15 team conducted an investigation using SIR-C, X-SAR, and Landsat TM data for estimating total above-ground dry biomass for the SSA and NSA modeling grids and component biomass for the SSA. Relationships of backscatter to total biomass and total biomass to foliage, branch, and bole biomass were used to estimate biomass density across the landscape. The procedure involved image classification with SAR and Landsat TM data and development of simple mapping techniques using combinations of SAR channels. For the SSA, the SIR-C data used were acquired on 06-Oct-1994, and the Landsat TM data used were acquired on 02-Sep-1995. The maps of the NSA were developed from SIR-C data acquired on 13-Apr-1994. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Inventory of the possibilities to process biomass using the existing industrial infrastructure

International Nuclear Information System (INIS)

Van Aart, F.J.J.M.; Barkhuysen, K.

1999-07-01

In the Netherlands, the government has formulated objectives for stimulating the use of sustainable energy and reducing CO 2 emissions. The replacement of fossil fuels by biomass is a major cornerstone of this policy. This has already resulted in a number of study projects, experiments and, in some cases, implementation projects in the co-fuelling of biomass in pulverised coal- or gas-fired power stations. Since the total energy use in the Netherlands depends only in part on power stations, it is still the question whether the total potential for the application of biomass in the Netherlands is being utilised. In order to study this question, Novem commissioned KEMA to make an inventory of the possibilities of processing biomass in industry via the existing infrastructure. The most important umbrella organisations, interest groups, sector organisations and leading companies have been approached in order to obtain insight into the potential of using biomass, and the willingness to do so. The following sectors of industry were selected: foodstuffs and luxury foods, chemicals, building materials, basic metals, metal products, glass and the fodder drying industry. In the cement industry and in the fodder drying industry, there is interest and there exist possibilities for using biomass as an alternative to fossil fuels in the existing industrial processes. The recommendation is to study in greater detail the feasibility of using biomass in the fodder drying industry. In the other sectors of industry which were investigated, there appeared to be little opportunity to use biomass in industrial processes. 4 refs

Effect of drying techniques on the retention of antioxidant activities of Saskatoon berries

Directory of Open Access Journals (Sweden)

Pranabendu Mitra

2013-10-01

Full Text Available The main objective of this research was to compare the retention of antioxidant activity and total anthocyanin content of Saskatoon berries dried by freeze drying, microwave-vacuum drying, thin layer hot air drying and vacuum drying. Antioxidant activity of berry samples was determined by DPPH radical scavenging and ABTS radical scavenging, and the pH differential method was used to determine total anthocyanin content of the berry samples. The results showed that the freeze dried Saskatoon berries exhibited the highest retention of anthocyanin and antioxidant activity among the dried samples, followed by microwave-vacuum dried berries, thin layer hot air dried berries and vacuum dried berries. There were significant differences between the berry samples at P<0.05.  DPPH radical scavenging and ABTS radical scavenging were correlated linearly with an R2 value of 0.99 at P<0.05 showing their effectiveness for the determination of the antioxidant activity of the Saskatoon berries. However, the DPPH radical scavenging assay was more effective than the ABTS radical scavenging assay. The results also showed that antioxidant activity of the berries was highly correlated with the total anthocyanin content of the fruit. The reduction of anthocyanin in dried berry samples was linearly correlated with the reduction of DPPH radical scavenging with an R2 value of 0.97 at P<0.05 and, also, linearly correlated with the reduction of ABTS radical scavenging with an R2 value of 0.88 at P<0.05.

Biomass production and water use efficiency of grassland in ...

African Journals Online (AJOL)

Using the results from a long-term grazing trial in the Dry Highland Sourveld of the KwaZulu-Natal province, we prepared a water use efficiency value (the ratio of the increment in annual biomass to total annual evapotranspiration) for this rangeland type. Using seasonal biomass measurements recorded between March ...

Biotransformation of vegetable and fruit processing wastes into yeast biomass enriched with selenium

Energy Technology Data Exchange (ETDEWEB)

Stabnikova, O.; Jing Yuan Wang; Hong Bo Ding; Joo Hwa Tay [Nanyang Technological Univ., Singapore (Singapore). School of Civil and Environmental Engineering

2005-04-01

Water extracts of cabbage, watermelon, a mixture of residual biomass of green salads and tropical fruits were used for yeast cultivation. These extracts contained from 1420 to 8900 mg/l of dissolved organic matter, and from 600 to 1800 mg/l of nitrogen. pH of the extracts was in the range from 4.1 to 6.4. Biomass concentration of yeast, Saccharomyces cerevisiae CEE 12 grown at 30 {sup o}C for 96 h in the sterilized extracts without any nutrient supplements was from 6.4 to 8.2 g/l; content of protein was from 40% to 45% of dry biomass. The yield was comparable with the yield of yeast biomass grown in potato dextrose broth. The biomass can be considered as the protein source. Its feed value was enhanced by incorporation of selenium in biomass to the level of 150 {mu}g/g of dry biomass. Therefore, it was recommended to transform the extracts from vegetable and fruit processing wastes into the yeast biomass enriched with selenium. (Author)

Estimation of lichen biomass with emphasis on reindeer winter pastures at Hardangervidda, S Norway

OpenAIRE

Arvid Odland; Sylvi M. Sandvik; Dag K. Bjerketvedt; Linn L. Myrvold

2014-01-01

Quantification of lichen abundance is important for management of reindeer populations. We measured dry lichen biomass in 876 micro plots (16.5 cm × 16.5 cm) systematically sampled within 219 vegetation plots (2 m × 2 m) from 7 different areas in S Norway. Lichen biomass was quantified as: (a) dry weight in g m-2, (b) lichen height in cm, (c) lichen cover, and (d) lichen volume (lichen height × lichen cover). Lichen biomass decreased with increasing precipitation and increasing altitude. On l...

Active Elastic Support/Dry Friction Damper with Piezoelectric Ceramic Actuator

Directory of Open Access Journals (Sweden)

Liao Mingfu

2014-01-01

Full Text Available The basic operation principle of elastic support/dry friction damper in rotor system was introduced and the unbalance response of the rotor with elastic support/dry friction damper was analyzed theoretically. Based on the previous structure using an electromagnet as actuator, an active elastic support/dry friction damper using piezoelectric ceramic actuator was designed and its effectiveness of reducing rotor vibration when rotor traverses its critical speed and blade-out event happened was experimentally verified. The experimental results show that the active elastic support/dry friction damper with piezoelectric ceramic actuator can significantly reduce vibration in rotor system; the vibration amplitude of the rotor in critical speed region decreased more than 2 times, and the active damper can protect the rotor when a blade-out event happened, so the rotor can traverse the critical speed and shut down smoothly. In addition, the structure is much simpler than the previous, the weight was reduced by half and the power consumption was only 5 W.

Below-ground biomass production and allometric relationships of eucalyptus coppice plantation in the central highlands of Madagascar

International Nuclear Information System (INIS)

Razakamanarivo, Ramarson H.; Razakavololona, Ando; Razafindrakoto, Marie-Antoinette; Vieilledent, Ghislain; Albrecht, Alain

2012-01-01

Short rotations of Eucalyptus plantations under coppice regime are extensively managed for wood production in Madagascar. Nevertheless, little is known about their biomass production and partitioning and their potential in terms of carbon sequestration. If above-ground biomass (AGB) can be estimated based on established allometric relations, below-ground (BGB) estimates are much less common. The aim of this work was to develop allometric equations to estimate biomass of these plantations, mainly for the root components. Data from 9 Eucalyptus robusta stands (47–87 years of plantation age, 3–5 years of coppice-shoot age) were collected and analyzed. Biomass of 3 sampled trees per stand was determined destructively. Dry weight of AGB components (leaves, branches and stems) were estimated as a function of basal area of all shoots per stump and dry weight for BGB components (mainly stump, coarse root (CR) and medium root (MR)) were estimated as a function of stump circumference. Biomass was then computed using allometric equations from stand inventory data. Stand biomass ranged from 102 to 130 Mg ha −1 with more than 77% contained in the BGB components. The highest dry weight was allocated in the stump and in the CR (51% and 42% respectively) for BGB parts and in the stem (69%) for AGB part. Allometric relationships developed herein could be applied to other Eucalyptus plantations which present similar stand density and growing conditions; anyhow, more is needed to be investigated in understanding biomass production and partitioning over time for this kind of forest ecosystem. -- Highlights: ► We studied the potential of old eucalyptus coppices in Madagascar to mitigate global warming. ► Biomass measurement, mainly for below-ground BGB (stump, coarse-medium-and fine roots) was provided. ► BGB allometry relationships for short rotation forestry under coppice were established. ► BGB were found to be important with their 102-130MgC ha -1 (<77% of the C in

Optimization of Preparation Program for Biomass Based Porous Active Carbon by Response Surface Methodology Based on Adsorptive Property

Directory of Open Access Journals (Sweden)

ZHANG Hao

2017-06-01

Full Text Available With waste walnut shell as raw material, biomass based porous active carbon was made by microwave oven method. The effects of microwave power, activation time and mass fraction of phosphoric acid on adsorptive property of biomass based porous active carbon in the process of physical activation of active carbon precursor were studied by response surface method and numerical simulation method, the preparation plan of biomass based porous active carbon was optimized, and the optimal biomass based porous active carbon property was characterized. The results show that three factors affect the adsorptive property of biomass based porous active carbon, but the effect of microwave power is obviously more significant than that of mass fraction of phosphoric acid, and the effect of mass fraction of phosphoric acid is more significant than that of activation time. The optimized preparation conditions are:microwave power is 746W, activation time is 11.2min and mass fraction of phosphoric acid is 85.9% in the process of physical activation of activated carbon precursor by microwave heating method. For the optimal biomass based porous active carbon, the adsorption value of iodine is 1074.57mg/g, adsorption value of methylene blue is 294.4mL/g and gain rate is 52.1%.

Assessment of microbial activity and biomass in different soils exposed to nicosulfuron

Directory of Open Access Journals (Sweden)

Ljiljana Šantrić

2014-09-01

Full Text Available The effects of the herbicide nicosulfuron on the abundance of cellulolytic and proteolytic microorganisms, activity of β-glucosidase and protease enzymes, and microbial phosphorus biomass were examined. A laboratory bioassay was set up on two types of agricultural soils differing in physicochemical properties. The following concentrations were tested: 0.3, 0.6, 3.0 and 30.0 mg a.i./kg of soil. Samples were collected 3, 7, 14, 30 and 45 days after treatment with nicosulfuron. The results showed that nicosulfuron significantly reduced the abundance of cellulolytic microorganisms in both soils, as well as microbial biomass phosphorus in sandy loam soil. The herbicide was found to stimulate β-glucosidase and protease activity in both types of soil and microbial biomass phosphorus in loamy soil. Proteolytic microorganisms remained unaffected by nicosulfuron.

The effect of different nutrient sources on biomass production of ...

African Journals Online (AJOL)

The effect of various organic, inorganic and complex compounds on the biomass production (mycelial dry weight) of Lepiota procera, a Nigerian edible higher fungus was investigated. Among the seventeen carbon compounds tested, mannose enhanced the best biomass yield. This was followed in order by glucose, ...

Development of an oven drying protocol to improve biodiesel production for an indigenous chlorophycean microalga Scenedesmus sp.

Science.gov (United States)

Bagchi, Sourav Kumar; Rao, Pavuluri Srinivasa; Mallick, Nirupama

2015-03-01

Drying of wet algal biomass is a major bottleneck in viable commercial production of the microalgal biodiesel. In the present investigation, an oven drying protocol was standardized for drying of wet Scenedesmus biomass at 60, 80 and 100°C with initial sample thickness of 5.0, 7.5 and 10.0mm. The optimum drying temperature was found to be 80°C with a maximum lipid yield of 425.0±5.9mgg(-1) at 15h drying time for 5.0mm thick samples with 0.033kWh power consumption. Partial drying at 80°C up to 10% residual moisture content was efficient showing 93% lipid recovery with 8h drying and a power consumption of 0.017kWh. Scenedesmus biomass was also found to be rich in saturated and mono-unsaturated fatty acids. Thus, the drying protocol demonstrates its suitability to improve the downstream processing of biodiesel production by significantly lowering the power consumption and the drying time. Copyright © 2014 Elsevier Ltd. All rights reserved.

Study on pore structure properties of steam activated biomass chars

Energy Technology Data Exchange (ETDEWEB)

Shu, Tong; Lu, Fei; Wang, Qinchao; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

2013-07-01

Wheat straw and rice husk chars were prepared in a fixed bed reactor at different pyrolysis temperatures (673, 873 and 1,073K) and different pyrolysis procedure. The steam activated chars were also prepared in a fixed bed reactor at the following conditions: activation temperature is 1,073K, the flow rate of N{sub 2} is 5L/min, and N{sub 2} and H{sub 2}O molar ratio is 1:1. The specific surface area, pore structure and micro-morphology of different kinds of prepared biomass chars were measured by NOVA1000e analysis instrument and JSM-5610LV scanning electron microscopy (SEM), respectively. Results indicated that the internal structure was improved significantly by steam activation through enlarging the specific surface area and enriching the porosity. The wheat straw char prepared by both rapid pyrolysis at 873K and activation by steam is better than others, whose DR surface area increases from 3.10 to 1099.99m{sup 2}/g. The N{sub 2} adsorption volume of steam activated biomass chars has been significant promoted.

Biomass production in energy plantation of Prosopis juliflora

Energy Technology Data Exchange (ETDEWEB)

Gurumurti, K.

1984-09-01

Studies on time trends of biomass production by means of age series in energy plantations (spacing 1.3 x 1.3 m) of Prosopis juliflora is presented. The component biomass production at the age of 18, 24, 30, 36 and 48 months was determined. The results show considerable variation among the population of trees. However, distinct linear relationship between girth at breast height (GBH) and total height was discernible. The total biomass produced at 18, 24, 30, 36 and 48 months of age was 19.69, 41.39, 69.11, 114.62 and 148.63 dry tonnes per hectare, respectively. The corresponding figures for utilizable biomass (wood, bark and branch) were 14.63, 32.17, 50.59, 88.87 and 113.25 dry tonnes per hectare. At all the periods of study, branch component formed the major portion of total biomass being around 50 to 55%. Utilizable biomass was three-fourths of total biomass at all ages. The solar energy conversion efficiency ranged from 0.59% at 18 months to 1.68% at 48 months of age, the peak value being 1.87% at the age of 36 months. It is shown that the variables diameter and height can be used to reliably predict the biomass production in Prosopis juliflora with the help of the regression equations developed in the present study. It is concluded that Prosopis juliflora is an ideal candidate for energy plantations in semi arid and marginal lands, not only to meet the fuelwood demands but also to improve the soil fertility, for, this plant is a fast growing and nitrogen fixing leguminous tree.

Biomass energetics potential of wetlands at Saare county

International Nuclear Information System (INIS)

Kask, U.; Kask, L.

2002-01-01

Most of the fuels that are being used to produce the thermal and electrical power are nonrenewable. Transferring them into energy pollutes the environment with CO 2 and surplus heat. Biomass is the most suitable energy resource in Estonian natural circumstances. Hitherto, one kind of biomass - plants of wetland - has almost not been used. There are plenty of wetlands in Saaremaa that have reasonably high productivity of biomass. Exertion of technologies of processing and using the biomass helps to create new jobs in agriculture as well in other sector of economy and evolve the regional development. The local currency circulation will improve and there are also possibilities in increase of capital expenditures and export potential. The biomass productivity of wetland plants accounting to dry matter can reach up to 4-5 kg/m 2 in a year. One advantage to use the plants of wetland (reed, cattail) in energy production is the fact that these plants will disengage from water in the end of their growth period and will need no extra drying. There are over 12000 ha of wetlands in Saaremaa, half of them could be used to get energetical biomass. The other half is either under (nature)protection or it would be economically inefficient to cut reed there. The major wetlands are in the surroundings of Mullatu bay and the Koigi swamp, also in Tornimae. There could be significant reduce in the emission of solid particles into the atmosphere, if the biomass of wetlands would be used to produce thermal and electrical power in Kuressaare. (author)

Anti-inflammatory and antinociceptive activities of Phyllanthus niruri spray-dried standardized extract

Directory of Open Access Journals (Sweden)

Cínthia R. C. Porto

2013-02-01

Full Text Available Phyllanthus niruri L., Euphorbiaceae, spray-dried standardized extract was studied for its anti-inflammatory and antinociceptive activities in adult albino rats and mice. The anti-inflammatory effect of spray-dried standardized extract was observed in carrageenan-induced paw edema and thioglycolate-induced leukocyte migration, while antinociceptive effects were observed using Randall & Selitto, tail flick, and hot plate tests. This study showed that intraperitoneal spray-dried standardized extract at 100, 200, 800, or 1600 mg/kg reduced the vascular response in the inflammatory process of paw edema induced by 1% carrageenan. Oral spray-dried standardized extract at 100 or 200 mg/kg inhibited leukocyte migration to the site of inflammation induced by 3% thioglycolate. In rats, at 100 and 200 mg/kg intraperitoneally, the extract exhibited a marked peripheral analgesic effect in a Randall & Selitto assay and showed significant central analgesic activity in a hot plate and tail flick assay. In conclusion, this study suggested that Phyllanthus niruri spray-dried standardized extract has potent inflammatory and antinociceptive activities and that these activities are not modified by standard drying process, making it feasible to use the dry extract standardized to obtain a phytotherapic preparation and thus validating its use for the treatment of pain and inflammation disorders.

Estimating Biomass of Barley Using Crop Surface Models (CSMs Derived from UAV-Based RGB Imaging

Directory of Open Access Journals (Sweden)

Juliane Bendig

2014-10-01

Full Text Available Crop monitoring is important in precision agriculture. Estimating above-ground biomass helps to monitor crop vitality and to predict yield. In this study, we estimated fresh and dry biomass on a summer barley test site with 18 cultivars and two nitrogen (N-treatments using the plant height (PH from crop surface models (CSMs. The super-high resolution, multi-temporal (1 cm/pixel CSMs were derived from red, green, blue (RGB images captured from a small unmanned aerial vehicle (UAV. Comparison with PH reference measurements yielded an R2 of 0.92. The test site with different cultivars and treatments was monitored during “Biologische Bundesanstalt, Bundessortenamt und CHemische Industrie” (BBCH Stages 24–89. A high correlation was found between PH from CSMs and fresh biomass (R2 = 0.81 and dry biomass (R2 = 0.82. Five models for above-ground fresh and dry biomass estimation were tested by cross-validation. Modelling biomass between different N-treatments for fresh biomass produced the best results (R2 = 0.71. The main limitation was the influence of lodging cultivars in the later growth stages, producing irregular plant heights. The method has potential for future application by non-professionals, i.e., farmers.

Effects of oxytetracycline, tylosin, and amoxicillin antibiotics on specific methanogenic activity of anaerobic biomass

Directory of Open Access Journals (Sweden)

Mohammad Mehdi Amin

2012-01-01

Materials and Methods: To evaluate the inhibitory antibiotics amoxicillin, tetracycline, and tylosin on biomass activity, specific methanogenic activity (SMA using anerobic biomass batch; into 120 ml vials: 30 ml biomass and 70 ml substrate including volatile fatty acids, mainly acetic acid and various concentrations of antibiotics were added. Methane gas production replacement through solution of KOH (2 N as an absorber of CO 2 and bromine thymol blue as indicator was measured. Each batch was tested for 10 days. Results: Based on the findings, inhibitory concentration of oxytetracycline, amoxicillin, and tylosin were 8000, 9000, and 9000 mg/L, respectively. Conclusions: This study showed that with increasing concentrations of antibiotics, the produced biogas volume from biomass per unit weight is decreased. COD removal was 42-82 % due to long retention time and adsorption to flocks.

Evaluation of hybrid solar – biomass dryer with no load

Directory of Open Access Journals (Sweden)

Yassen Tadahmun Ahmed

2014-07-01

Full Text Available Experimental study was carried out to investigate the performance of designed and fabricated hybrid solar-biomass dryer without load. The solar side was a natural convection mixed mode, while the biomass side was a hot air produced from a burner/gas to gas heat exchanger. The experiments have been conducted to test the dryer temperature, inlet and outlet relative humidity, outlet velocity, and biomass feeding rate. In the solar mode the maximum dryer temperature was 63°C. Behaviours of the velocity in the dryer was found to follow solar radiation available to the dryer. The velocity was in the range of 0.6 – 1.35 m/s through the 0.0176 m2 area of the outlet when the solar radiation was in the range of 150 – 880 W/m2. Two feeding rates of wood were used to investigate the dryer performance through the night. The results showed that at feeding rate 278 g/hr, the drying air mean temperature was 62 ºC. This temperature was more suitable than the measured drying air temperature at feeding rate 490 g/hr. Also the 62 °C drying environment is more stable and feasible for drying almost all types of products.

Designing CAF-adjuvanted dry powder vaccines: spray drying preserves the adjuvant activity of CAF01.

Science.gov (United States)

Ingvarsson, Pall Thor; Schmidt, Signe Tandrup; Christensen, Dennis; Larsen, Niels Bent; Hinrichs, Wouter Leonardus Joseph; Andersen, Peter; Rantanen, Jukka; Nielsen, Hanne Mørck; Yang, Mingshi; Foged, Camilla

2013-05-10

Dry powder vaccine formulations are highly attractive due to improved storage stability and the possibility for particle engineering, as compared to liquid formulations. However, a prerequisite for formulating vaccines into dry formulations is that their physicochemical and adjuvant properties remain unchanged upon rehydration. Thus, we have identified and optimized the parameters of importance for the design of a spray dried powder formulation of the cationic liposomal adjuvant formulation 01 (CAF01) composed of dimethyldioctadecylammonium (DDA) bromide and trehalose 6,6'-dibehenate (TDB) via spray drying. The optimal excipient to stabilize CAF01 during spray drying and for the design of nanocomposite microparticles was identified among mannitol, lactose and trehalose. Trehalose and lactose were promising stabilizers with respect to preserving liposome size, as compared to mannitol. Trehalose and lactose were in the glassy state upon co-spray drying with the liposomes, whereas mannitol appeared crystalline, suggesting that the ability of the stabilizer to form a glassy matrix around the liposomes is one of the prerequisites for stabilization. Systematic studies on the effect of process parameters suggested that a fast drying rate is essential to avoid phase separation and lipid accumulation at the surface of the microparticles during spray drying. Finally, immunization studies in mice with CAF01 in combination with the tuberculosis antigen Ag85B-ESAT6-Rv2660c (H56) demonstrated that spray drying of CAF01 with trehalose under optimal processing conditions resulted in the preservation of the adjuvant activity in vivo. These data demonstrate the importance of liposome stabilization via optimization of formulation and processing conditions in the engineering of dry powder liposome formulations. Copyright © 2013 Elsevier B.V. All rights reserved.

Development of activated carbon pore structure via physical and chemical activation of biomass fibre waste

International Nuclear Information System (INIS)

Williams, Paul T.; Reed, Anton R.

2006-01-01

Biomass waste in the form of biomass flax fibre, produced as a by-product of the textile industry was processed via both physical and chemical activation to produce activated carbons. The surface area of the physically activated carbons were up to 840 m 2 g -1 and the carbons were of mesoporous structure. Chemical activation using zinc chloride produced high surface area activated carbons up to 2400 m 2 g -1 and the pore size distribution was mainly microporous. However, the process conditions of temperature and zinc chloride concentration could be used to manipulate the surface area and porosity of the carbons to produce microporous, mesoporous and mixed microporous/mesoporous activated carbons. The physically activated carbons were found to be a mixture of Type I and Type IV carbons and the chemically activated carbons were found to be mainly Type I carbons. The development of surface morphology of physically and chemically activated carbons observed via scanning electron microscopy showed that physical activation produced activated carbons with a nodular and pitted surface morphology whereas activated carbons produced through chemical activation had a smooth surface morphology. Transmission electron microscopy analysis could identify mesopore structures in the physically activated carbon and microporous structures in the chemically activated carbons

FY 2000 Report on survey results. Curtailment of the carbon dioxide emission by effective use of woody biomass system waste; 2000 nendo mokushitsu biomass kei haikibutsu no yuko riyo ni yoru nisanka tanso haishutsu no sakugen

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

It is estimated that the woody biomass resources in Japan total 42.70 million t/y on a dry basis (indigenous production: 20.00 million t/y), which corresponds to 18.00 million t/y as oil. This project studies effective utilization of low-quality biomass resources now discarded, e.g., thinning materials and demolition woods, by reference to biomass utilization pursued in European and North American countries. The study activities cover the 3 areas of woody biomass wastes, current status of biomass utilization technologies in the overseas countries, and feasibility of introduction of the utilization technologies, after investigating necessity of abatement of the green-effect gases, current status of energy demands and policies, and woody biomass. Utilization of biomass resources for low-temperature heat purposes, which is the central issue in Japan, is not well established both technologically and politically. Moreover, the biomass resources are not exposed to price competition. Based on these premises, a total of 6 scenarios are proposed to promote utilization of biomass resources, including power/heat co-generation at a wood processing center, and dual firing at existing coal-fired boilers. (NEDO)

Estimating forest and woodland aboveground biomass using active and passive remote sensing

Science.gov (United States)

Wu, Zhuoting; Dye, Dennis G.; Vogel, John M.; Middleton, Barry R.

2016-01-01

Aboveground biomass was estimated from active and passive remote sensing sources, including airborne lidar and Landsat-8 satellites, in an eastern Arizona (USA) study area comprised of forest and woodland ecosystems. Compared to field measurements, airborne lidar enabled direct estimation of individual tree height with a slope of 0.98 (R2 = 0.98). At the plot-level, lidar-derived height and intensity metrics provided the most robust estimate for aboveground biomass, producing dominant species-based aboveground models with errors ranging from 4 to 14Mg ha –1 across all woodland and forest species. Landsat-8 imagery produced dominant species-based aboveground biomass models with errors ranging from 10 to 28 Mg ha –1. Thus, airborne lidar allowed for estimates for fine-scale aboveground biomass mapping with low uncertainty, while Landsat-8 seems best suited for broader spatial scale products such as a national biomass essential climate variable (ECV) based on land cover types for the United States.

Green energy from microalgae: Usage of algae biomass for anaerobic digestion

International Nuclear Information System (INIS)

Skorupskaite, Virginija; Makarevicie, Violeta

2014-01-01

The microalgae biomass can be used for various types of biofuels, including biodiesel and biogas. The aim of this study is to investigate the possibilities of microalgae Scenedesmus sp. and Chlorella sp. (widespread in freshwater Lithuanian lakes) usage for biogas production. Microalgae were cultivated under mixotrophic conditions (growth medium BG11 containing technical glycerol). In order to determine biogas yield and quality dependence on feedstock preparation, the analyses of biogas production have been performed with algae biomass prepared i n different ways: wet centrifuged; wet centrifuged, frozen and defrost; dry not de-oiled and dry de-oiled. The highest biogas yield in both cases (Scenedesmus sp. – 646 ml/gDM and Chlorella sp. – 652 ml/gDM) was obtained from centrifuged, frozen and defrost biomass. Biogas yield was app. 1.46 times higher comparing to yield of biogas produced from wastewater sludge. Our results showed that different types of biomass preparation have no significant influence on quality of biogas. Key words: microalgae, biomass, biogas production, biogas quality

Model Effects on GLAS-Based Regional Estimates of Forest Biomass and Carbon

Science.gov (United States)

Nelson, Ross F.

2010-01-01

Ice, Cloud, and land Elevation Satellite (ICESat) / Geosciences Laser Altimeter System (GLAS) waveform data are used to estimate biomass and carbon on a 1.27 X 10(exp 6) square km study area in the Province of Quebec, Canada, below the tree line. The same input datasets and sampling design are used in conjunction with four different predictive models to estimate total aboveground dry forest biomass and forest carbon. The four models include non-stratified and stratified versions of a multiple linear model where either biomass or (biomass)(exp 0.5) serves as the dependent variable. The use of different models in Quebec introduces differences in Provincial dry biomass estimates of up to 0.35 G, with a range of 4.94 +/- 0.28 Gt to 5.29 +/-0.36 Gt. The differences among model estimates are statistically non-significant, however, and the results demonstrate the degree to which carbon estimates vary strictly as a function of the model used to estimate regional biomass. Results also indicate that GLAS measurements become problematic with respect to height and biomass retrievals in the boreal forest when biomass values fall below 20 t/ha and when GLAS 75th percentile heights fall below 7 m.

Effect of microwave drying and oven drying on the water activity, color, phenolic compounds content and antioxidant activity of coconut husk (Cocos nucifera L.).

Science.gov (United States)

Valadez-Carmona, Lourdes; Cortez-García, Rosa María; Plazola-Jacinto, Carla Patricia; Necoechea-Mondragón, Hugo; Ortiz-Moreno, Alicia

2016-09-01

The coconut ( Cocos nucifera L.) husk is basically composed by fiber and pith material and remained under-utilized. This is an important source of phenolic compounds that could be used as functional ingredients. The aim of this study was to determine the effect of: oven-drying (OD) and microwave drying (MD), on the water activity, color, phenolic compound content and antioxidant activity of coconut husk. The OD was performed at 60 °C for 12 h and MD was performed at 900 W for 10 min. The total phenolic content (TPC) in fresh coconut husk was 64.2 mg GAE/g dry wt and significant higher than observed after OD and MD of 35.8 and 45.5 mg GAE/g dry wt, respectively. Ten phenols were identified in fresh and dehydrated coconut husks. The husk MD showed an increase in the content of gallic, 4-hydroxybenzoic, ferulic and syringic acids and epicatechin compared with the fresh; while coconut husk OD and MD, showed a decrease in the content of vanillic acid, vanillin, catequin and kaempferol. The antioxidant activity decreased after both OD and MD. However, MD resulted in a better antioxidant activity in husk than OD. MD of husk resulted into better retention of preserved color, TPC and TFC than OD.

Drying of α-amylase by spray drying and freeze-drying - a comparative study

Directory of Open Access Journals (Sweden)

S. S. de Jesus

2014-09-01

Full Text Available This study is aimed at comparing two traditional methods of drying of enzymes and at verifying the efficiency of each one and their advantages and disadvantages. The experiments were performed with a laboratory spray dryer and freeze-dryer using α-amylase as the model enzyme. An experimental design in star revealed that spray drying is mainly influenced by the inlet air temperature and feed flow rate, which were considered to be the main factors influencing the enzymatic activity and water activity; the long period of material exposure to high temperatures causes a partial activity loss. In the experiments of freeze drying, three methods of freezing were used (freezer, acetone and dry ice, and liquid nitrogen and samples subsequently freeze-dried for times ranging between 0-24 hours. The product obtained from the two techniques showed high enzymatic activity and low water activity. For the drying of heat-resistant enzymes, in which the product to be obtained does not have high added value, spray drying may be more economically viable because, in the freeze drying process, the process time can be considered as a limiting factor when choosing a technique.

Cellulase digestibility of pretreated biomass is limited by cellulose accessibility.

Science.gov (United States)

Jeoh, Tina; Ishizawa, Claudia I; Davis, Mark F; Himmel, Michael E; Adney, William S; Johnson, David K

2007-09-01

Attempts to correlate the physical and chemical properties of biomass to its susceptibility to enzyme digestion are often inconclusive or contradictory depending on variables such as the type of substrate, the pretreatment conditions and measurement techniques. In this study, we present a direct method for measuring the key factors governing cellulose digestibility in a biomass sample by directly probing cellulase binding and activity using a purified cellobiohydrolase (Cel7A) from Trichoderma reesei. Fluorescence-labeled T. reesei Cel7A was used to assay pretreated corn stover samples and pure cellulosic substrates to identify barriers to accessibility by this important component of cellulase preparations. The results showed cellulose conversion improved when T. reesei Cel7A bound in higher concentrations, indicating that the enzyme had greater access to the substrate. Factors such as the pretreatment severity, drying after pretreatment, and cellulose crystallinity were found to directly impact enzyme accessibility. This study provides direct evidence to support the notion that the best pretreatment schemes for rendering biomass more digestible to cellobiohydrolase enzymes are those that improve access to the cellulose in biomass cell walls, as well as those able to reduce the crystallinity of cell wall cellulose.

Uso de biomassa seca de aguapé (Eichornia crassipes visando à remoção de metais pesados de soluções contaminadas = Use of water hyacinth (Eichornia crassipes dry biomass for removing heavy metals from contaminated solutions

Directory of Open Access Journals (Sweden)

Affonso Celso Gonçalves Junior

2009-01-01

Full Text Available O presente trabalho avaliou a eficiência da biomassa seca de aguapé (Eichornia crassipes na remoção dos metais pesados cádmio (Cd, chumbo (Pb, cromo (Cr, cobre (Cu, zinco (Zn e níquel (Ni de soluções preparadas com estes metais. O delineamento utilizado foi inteiramente casualizado, com cinco tratamentos (soluções com diferentes concentrações dos metais pesados e quatro repetições. A biomassa seca permaneceu nas soluções dos tratamentos por um período de 48h, e nos intervalos de 1; 2; 3; 6; 12; 24; 36 e 48h após a instalação do experimento, coletaram-se alíquotas de cada tratamento,determinando-se a maior remoção de cada metal pesado pela biomassa seca do aguapé. Foi realizada digestão nitroperclórica na biomassa seca e determinação dos teores dos metais na biomassa e nas alíquotas por espectrometria de absorção atômica, modalidade chama. Paraos metais Cd, Pb, Cr, Cu e Zn ocorreu remoção significativa pela massa seca do aguapé nos diferentes tratamentos, enquanto para o Ni não foi encontrada diferença significativa. Dessa forma, conclui-se que a biomassa seca produzida, a partir do aguapé Eichornia crassipes, é um excelente material para a remoção, tanto em pequena como em grande escala, de corpos hídricos contaminados com metais pesados.The present work evaluated the efficiency of the dry biomass of water hyacinth (Eichornia crassipes in the removal of heavy metalscadmium (Cd, lead (Pb, chromium (Cr, cupper (Cu, zinc (Zn and nickel (Ni from solutions prepared with these metals. The delineation used was entirely randomized, with five treatments (solutions with different concentrations of heavy metals and fourrepetitions. The dry biomass remained in the treatment solutions for a period of 48h. In the intervals of 1; 2; 3; 6; 12; 24; 36 and 48h after experiment installation, samples were collected of each treatment, determining the greater removal for each heavy metal by water hyacinth dry biomass. Nitro

Integration of biomass fast pyrolysis and precedent feedstock steam drying with a municipal combined heat and power plant

International Nuclear Information System (INIS)

Kohl, Thomas; Laukkanen, Timo P.; Järvinen, Mika P.

2014-01-01

Biomass fast pyrolysis (BFP) is a promising pre-treatment technology for converting biomass to transport fuel and in the future also for high-grade chemicals. BFP can be integrated with a municipal combined heat and power (CHP) plant. This paper shows the influence of BFP integration on a CHP plant's main parameters and its effect on the energetic and environmental performance of the connected district heating network. The work comprises full- and part-load operation of a CHP plant integrated with BFP and steam drying. It also evaluates different usage alternatives for the BFP products (char and oil). The results show that the integration is possible and strongly beneficial regarding energetic and environmental performance. Offering the possibility to provide lower district heating loads, the operation hours of the plant can be increased by up to 57%. The BFP products should be sold rather than applied for internal use as this increases the district heating network's primary energy efficiency the most. With this integration strategy future CHP plants can provide valuable products at high efficiency and also can help to mitigate global CO 2 emissions. - Highlights: • Part load simulation of a cogeneration plant integrated with biomas fast pyrolysis. • Analysis of energetic and environmental performance. • Assessment of different uses of the pyrolysis products

Short-term parasite-infection alters already the biomass, activity and functional diversity of soil microbial communities

Science.gov (United States)

Li, Jun-Min; Jin, Ze-Xin; Hagedorn, Frank; Li, Mai-He

2014-11-01

Native parasitic plants may be used to infect and control invasive plants. We established microcosms with invasive Mikania micrantha and native Coix lacryma-jobi growing in mixture on native soils, with M. micrantha being infected by parasitic Cuscuta campestris at four intensity levels for seven weeks to estimate the top-down effects of plant parasitism on the biomass and functional diversity of soil microbial communities. Parasitism significantly decreased root biomass and altered soil microbial communities. Soil microbial biomass decreased, but soil respiration increased at the two higher infection levels, indicating a strong stimulation of soil microbial metabolic activity (+180%). Moreover, a Biolog assay showed that the infection resulted in a significant change in the functional diversity indices of soil microbial communities. Pearson correlation analysis indicated that microbial biomass declined significantly with decreasing root biomass, particularly of the invasive M. micrantha. Also, the functional diversity indices of soil microbial communities were positively correlated with soil microbial biomass. Therefore, the negative effects on the biomass, activity and functional diversity of soil microbial community by the seven week long plant parasitism was very likely caused by decreased root biomass and root exudation of the invasive M. micrantha.

Development of biomass in a drinking water granular active carbon (GAC) filter.

Science.gov (United States)

Velten, Silvana; Boller, Markus; Köster, Oliver; Helbing, Jakob; Weilenmann, Hans-Ulrich; Hammes, Frederik

2011-12-01

Indigenous bacteria are essential for the performance of drinking water biofilters, yet this biological component remains poorly characterized. In the present study we followed biofilm formation and development in a granular activated carbon (GAC) filter on pilot-scale during the first six months of operation. GAC particles were sampled from four different depths (10, 45, 80 and 115 cm) and attached biomass was measured with adenosine tri-phosphate (ATP) analysis. The attached biomass accumulated rapidly on the GAC particles throughout all levels in the filter during the first 90 days of operation and maintained a steady state afterward. Vertical gradients of biomass density and growth rates were observed during start-up and also in steady state. During steady state, biomass concentrations ranged between 0.8-1.83 x 10(-6) g ATP/g GAC in the filter, and 22% of the influent dissolved organic carbon (DOC) was removed. Concomitant biomass production was about 1.8 × 10(12) cells/m(2)h, which represents a yield of 1.26 × 10(6) cells/μg. The bacteria assimilated only about 3% of the removed carbon as biomass. At one point during the operational period, a natural 5-fold increase in the influent phytoplankton concentration occurred. As a result, influent assimilable organic carbon concentrations increased and suspended bacteria in the filter effluent increased 3-fold as the direct consequence of increased growth in the biofilter. This study shows that the combination of different analytical methods allows detailed quantification of the microbiological activity in drinking water biofilters. Copyright © 2011 Elsevier Ltd. All rights reserved.

Production of Solid Fuel by Torrefaction Using Coconut Leaves As Renewable Biomass

Directory of Open Access Journals (Sweden)

Lola Domnina Bote Pestaño

2016-11-01

Full Text Available The reserves of non-renewable energy sources such as coal, crude oil and natural gas are not limitless, they gradually get exhausted and their price continually increases. In the last four decades, researchers have been focusing on alternate fuel resources to meet the ever increasing energy demand and to avoid dependence on crude oil. Amongst different sources of renewable energy, biomass residues hold special promise due to their inherent capability to store solar energy and amenability to subsequent conversion to convenient solid, liquid and gaseous fuels. At present, among the coconut farm wastes such as husks, shell, coir dust and coconut leaves, the latter is considered the most grossly under-utilized by in situ burning in the coconut farm as means of disposal. In order to utilize dried coconut leaves and to improve its biomass properties, this research attempts to produce solid fuel by torrefaction using dried coconut leaves for use as alternative source of energy. Torrefaction is a thermal method for the conversion of biomass operating in the low temperature range of 200oC-300oC under atmospheric conditions in absence of oxygen. Dried coconut leaves were torrefied at different feedstock conditions. The key torrefaction products were collected and analyzed. Physical and combustion characteristics of both torrefied and untorrefied biomass were investigated. Torrefaction of dried coconut leaves significantly improved the heating value compared to that of the untreated biomass.  Proximate compositions of the torrefied biomass also improved and were comparable to coal. The distribution of the products of torrefaction depends highly on the process conditions such as torrefaction temperature and residence time. Physical and combustion characteristics of torrefied biomass were superior making it more suitable for fuel applications. Article History: Received June 24th 2016; Received in revised form August 16th 2016; Accepted 27th 2016; Available

Deliverable D2.4: Status of Dry Electrode Development Activity

NARCIS (Netherlands)

Mihajlovic, V.; Garcia Molina, G.

2010-01-01

The goal of dry electrode development activity within the WP2 is tobuild a dry electrode prototype for brain wave sensing that is comfortable for the user and provides sufficient signal quality. The electrodes are to be utilized in BCI applications, namely Steady-StateVisually Evoked Potential

Effect Carrier Agent Formulation in Drying Rate and Antioxidant Activity of Roselle Extract

Directory of Open Access Journals (Sweden)

Utari Febiani Dwi

2018-01-01

Full Text Available Roselle (Hibiscus sabdarifa L contains anthocyanins as the natural colorant and antioxidant. Drying the roselle extract was aims to produce the dry product that easy consumption as antioxidant. The carrier agent was added in roselle extract to improve the drying rate and maintain the nutritional value. This research studied the effect of carrier agent in drying rate and antioxidant activity. The method consists of two step involving roselle extraction using ultrasonic and the drying process. The roselle extraction by ultrasonic use the water as the solvent. The carrier agent (0%,5%,10% of maltodextrin was added in roselle extract. The mixture was then dried in tray dryer dehumidification using zeolite in drying temperature 50,60, and 70⁰C. As the response, the moisture content was observed by gravimetry every 15 minutes for 150 minutes. The result showed that Page model was fitted to determine the constant of drying rate. Higher concentration of carrier agent enhanced the moisture evaporation process. Based on the DPPH analysis, the degradation of antioxidant activity in temperature 70⁰C was 2.14 times higher than in temperature 50⁰C. As the conclusion, addition of maltodextrin can speed up the drying process and retain the antioxidant activity of.

DRI Renewable Energy Center (REC) (NV)

Energy Technology Data Exchange (ETDEWEB)

Hoekman, S. Kent; Broch, Broch; Robbins, Curtis; Jacobson, Roger; Turner, Robert

2012-12-31

The primary objective of this project was to utilize a flexible, energy-efficient facility, called the DRI Renewable Energy Experimental Facility (REEF) to support various renewable energy research and development (R&D) efforts, along with education and outreach activities. The REEF itself consists of two separate buildings: (1) a 1200-ft2 off-grid capable house and (2) a 600-ft2 workshop/garage to support larger-scale experimental work. Numerous enhancements were made to DRI's existing renewable power generation systems, and several additional components were incorporated to support operation of the REEF House. The power demands of this house are satisfied by integrating and controlling PV arrays, solar thermal systems, wind turbines, an electrolyzer for renewable hydrogen production, a gaseous-fuel internal combustion engine/generator set, and other components. Cooling needs of the REEF House are satisfied by an absorption chiller, driven by solar thermal collectors. The REEF Workshop includes a unique, solar air collector system that is integrated into the roof structure. This system provides space heating inside the Workshop, as well as a hot water supply. The Workshop houses a custom-designed process development unit (PDU) that is used to convert woody biomass into a friable, hydrophobic char that has physical and chemical properties similar to low grade coal. Besides providing sufficient space for operation of this PDU, the REEF Workshop supplies hot water that is used in the biomass treatment process. The DRI-REEF serves as a working laboratory for evaluating and optimizing the performance of renewable energy components within an integrated, residential-like setting. The modular nature of the system allows for exploring alternative configurations and control strategies. This experimental test bed is also highly valuable as an education and outreach tool both in providing an infrastructure for student research projects, and in highlighting renewable

Biomass and biochemical composition of zooplankton from northwest Bay of Bengal during January 1990

Digital Repository Service at National Institute of Oceanography (India)

Krishnakumari, L.; Goswami, S.C.

Biomass, proximate composition, organic carbon and calorie content of assorted zooplankton from the surface waters were studied. Day and night stations revealed significant difference in biomass (displacement volume, dry wt and organic carbon...

Antioxidant defense parameters as predictive biomarkers for fermentative capacity of active dried wine yeast.

Science.gov (United States)

Gamero-Sandemetrio, Esther; Gómez-Pastor, Rocío; Matallana, Emilia

2014-08-01

The production of active dried yeast (ADY) is a common practice in industry for the maintenance of yeast starters and as a means of long term storage. The process, however, causes multiple cell injuries, with oxidative damage being one of the most important stresses. Consequentially, dehydration tolerance is a highly appreciated property in yeast for ADY production. In this study we analyzed the cellular redox environment in three Saccharomyces cerevisiae wine strains, which show markedly different fermentative capacities after dehydration. To measure/quantify the effect of dehydration on the S. cerevisiae strains, we used: (i) fluorescent probes; (ii) antioxidant enzyme activities; (ii) intracellular damage; (iii) antioxidant metabolites; and (iv) gene expression, to select a minimal set of biochemical parameters capable of predicting desiccation tolerance in wine yeasts. Our results show that naturally enhanced antioxidant defenses prevent oxidative damage after wine yeast biomass dehydration and improve fermentative capacity. Based on these results we chose four easily assayable parameters/biomarkers for the selection of industrial yeast strains of interest for ADY production: trehalose and glutathione levels, and glutathione reductase and catalase enzymatic activities. Yeast strains selected in accordance with this process display high levels of trehalose, low levels of oxidized glutathione, a high induction of glutathione reductase activity, as well as a high basal level and sufficient induction of catalase activity, which are properties inherent in superior ADY strains. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Strength and Drying Shrinkage of Alkali-Activated Slag Paste and Mortar

Directory of Open Access Journals (Sweden)

Mao-chieh Chi

2012-01-01

Full Text Available The aim of this study is to investigate the strengths and drying shrinkage of alkali-activated slag paste and mortar. Compressive strength, tensile strength, and drying shrinkage of alkali-activated slag paste and mortar were measured with various liquid/slag ratios, sand/slag ratios, curing ages, and curing temperatures. Experimental results show that the higher compressive strength and tensile strength have been observed in the higher curing temperature. At the age of 56 days, AAS mortars show higher compressive strength than Portland cement mortars and AAS mortars with liquid/slag ratio of 0.54 have the highest tensile strength in all AAS mortars. In addition, AAS pastes of the drying shrinkage are higher than AAS mortars. Meanwhile, higher drying shrinkage was observed in AAS mortars than that observed comparable Portland cement mortars.

Non-canonical regulation of glutathione and trehalose biosynthesis characterizes non-Saccharomyces wine yeasts with poor performance in active dry yeast production

Directory of Open Access Journals (Sweden)

Esther Gamero-Sandemetrio

2018-01-01

Full Text Available Several yeast species, belonging to Saccharomyces and non-Saccharomyces genera, play fundamental roles during spontaneous must grape fermentation, and recent studies have shown that mixed fermentations, co-inoculated with S. cerevisiae and non-Saccharomyces strains, can improve wine organoleptic properties. During active dry yeast (ADY production, antioxidant systems play an essential role in yeast survival and vitality as both biomass propagation and dehydration cause cellular oxidative stress and negatively affect technological performance. Mechanisms for adaptation and resistance to desiccation have been described for S. cerevisiae, but no data are available on the physiology and oxidative stress response of non-Saccharomyces wine yeasts and their potential impact on ADY production. In this study we analyzed the oxidative stress response in several non-Saccharomyces yeast species by measuring the activity of reactive oxygen species (ROS scavenging enzymes, e.g., catalase and glutathione reductase, accumulation of protective metabolites, e.g., trehalose and reduced glutathione (GSH, and lipid and protein oxidation levels. Our data suggest that non-canonical regulation of glutathione and trehalose biosynthesis could cause poor fermentative performance after ADY production, as it corroborates the corrective effect of antioxidant treatments, during biomass propagation, with both pure chemicals and food-grade argan oil.

The Influence of Stress Treatments on the Microbial Biomass and the Rate of Decomposition of Humified Matter in Soils Containing Different Amounts of Clay

DEFF Research Database (Denmark)

Sørensen, Lasse Holst

1983-01-01

originating from straw. The addition of unlabeled glucose accelerated the evolution of labeled CO2-C in all 4 soils. The size of the effect on CO2 evolution and on the biomass was similar to that of air-drying. Grinding killed a larger percentage of the biomass in the sandy soil than in the soils with a high...... with CHCl3 mainly consists of dormant organisms. CO2 production, the biological activity, was related to the amount of available organic material and not the size of the biomass....

Changes in vegetation structure and aboveground biomass in ...

African Journals Online (AJOL)

Changes in vegetation structure and aboveground biomass in response to traditional rangeland management practices in Borana, southern Ethiopia. ... managed by prescribed fire for five years and grazed only post-fire during dry seasons.

Factors Influencing the Ignition and Burnout of a Single Biomass Particle

DEFF Research Database (Denmark)

Momenikouchaksaraei, Maryam; Kær, Søren Knudsen; Yin, Chungen

2011-01-01

Ignition and burnout of a single biomass particle were studied numerically. A one-dimensional particle combustion model was developed which is capable to simulate all the intraparticle conversion processes (drying, recondensation, devolatilization, char gasification/oxidation and heat/mass/moment......Ignition and burnout of a single biomass particle were studied numerically. A one-dimensional particle combustion model was developed which is capable to simulate all the intraparticle conversion processes (drying, recondensation, devolatilization, char gasification/oxidation and heat...... concentration were not very significant. The influences of these factors on particle burnout were much more remarkable than ignition behaviour....

Integrated resource management of biomass

International Nuclear Information System (INIS)

Goodwin, E.R.

1992-01-01

An overview is presented of the use of biomass, with emphasis on peat, as an alternative energy source, from an integrated resource management perspective. Details are provided of the volume of the peat resource, economics of peat harvesting, and constraints to peat resource use, which mainly centre on its high water content. Use of waste heat to dry peat can increase the efficiency of peat burning for electric power generation, and new technologies such as gasification and turbo expanders may also find utilization. The burning or gasification of biomass will release no more carbon dioxide to the atmosphere than other fuels, has less sulfur content than solid fuels. The removal of peat reduces methane emissions and allows use of produced carbon dioxide for horticulture and ash for fertilizer, and creates space that may be used for forestry or agricultural biomass growth. 38 refs

Process Design and Economics for the Production of Algal Biomass: Algal Biomass Production in Open Pond Systems and Processing Through Dewatering for Downstream Conversion

Energy Technology Data Exchange (ETDEWEB)

Davis, Ryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Markham, Jennifer [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kinchin, Christopher [National Renewable Energy Lab. (NREL), Golden, CO (United States); Grundl, Nicholas [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tan, Eric C.D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Humbird, David [DWH Process Consulting, Denver, CO (United States)

2016-02-17

This report describes in detail a set of aspirational design and process targets to better understand the realistic economic potential for the production of algal biomass for subsequent conversion to biofuels and/or coproducts, based on the use of open pond cultivation systems and a series of dewatering operations to concentrate the biomass up to 20 wt% solids (ash-free dry weight basis).

Selection of Willows (Salix sp. for Biomass Production

Directory of Open Access Journals (Sweden)

Davorin Kajba

2014-12-01

Full Text Available Background and Purpose: Willows compared with other species are the most suitable for biomass production in short rotations because of their very abundant growth during the first years. Nowadays, in Croatia, a large number of selected and registered willow clones are available. The main objective of the research should be to find genotypes which, with minimum nutrients, will produce the maximum quantity of biomass. Material and Methods: Clonal test of the arborescent willows include the autochthonous White Willow (Salix alba, interracial hybrids of the autochthonous White Willow and the English ‘cricket’ Willow (S. alba var. calva, interspecies hybrids (S. matsudana × S. alba, as well as multispecies hybrids of willows. Average production of dry biomass (DM∙ha-1∙a-1 per hectare was estimated in regard to the clone, survival, spacing and the number of shoots per stump. Results: The highest biomass production as well as the best adaptedness and phenotypic stability on testing site was shown by clones (‘V 374’, ‘V 461’, ‘V 578’ from 15.2 - 25.0 t∙DM∙ha-1∙a-1 originated from backcross hybrid S. matsudana × (S. matsudana × S. alba and by one S. alba clone (‘V 95’, 23.1 - 25.7 t∙DM∙ha-1∙a-1. These clones are now at the stage of registration and these results indicate significant potential for further breeding aimed at biomass production in short rotations. Conclusions: Willow clones showed high biomass production on marginal sites and dry biomass could be considerably increased with the application of intensive silvicultural and agro technical measures. No nutrition or pest control measures were applied (a practice otherwise widely used in intensive cultivation system, while weed vegetation was regulated only at the earliest age.

Effect of incorporation of walnut cake (Juglans regia in concentrate mixture on degradation of dry matter, organic matter and production of microbial biomass in vitro in goat

Directory of Open Access Journals (Sweden)

Mohsin Ahmad Mir

2015-10-01

Full Text Available Aim: This study was carried out to investigate the effect of incorporation of different level of walnut cake in concentrate mixture on in vitro dry matter degradation in order to determine its level of supplementation in ruminant ration. Materials and Methods: Walnut cake was used @ 0, 10, 15, 20, 25 and 30% level to formulate an iso-nitrogenous concentrate mixtures and designated as T1, T2, T3, T4, T5 and T6 respectively. The different formulae of concentrate mixtures were used for in vitro gas production studies using goat rumen liquor with wheat straw in 40:60 ratio. Proximate composition, fiber fractionation and calcium and phosphrous content of walnut cake were estimated. Result: The per cent IVDMD value of T1 and T2 diets was 68.42 ± 1.20 and 67.25 ± 1.37 respectively which was found highest (P<0.05 T3, T4, T5 and T6. Similar trend was also found for TDOM and MBP. Inclusion of walnut cake at 10% level in the concentrate mixture does not affect in vitro dry matter digestibility (IVDMD, truly degradable organic matter (TDOM, mg/200 mg DM, total gas production, microbial biomass production (MBP and efficiency of microbial biomass production (EMP. Conclusion: It is concluded that walnut cake incorporation up to 10% level in the iso -nitrogenous concentrate mixture has no any negative effect on in vitro digestibility of dry matter (DM, TDOM, MBP, EMP and total gas production in goat.

Emission factors from residential combustion appliances burning Portuguese biomass fuels.

Science.gov (United States)

Fernandes, A P; Alves, C A; Gonçalves, C; Tarelho, L; Pio, C; Schimdl, C; Bauer, H

2011-11-01

Smoke from residential wood burning has been identified as a major contributor to air pollution, motivating detailed emission measurements under controlled conditions. A series of experiments were performed to compare the emission levels from two types of wood-stoves to those of fireplaces. Eight types of biomass were burned in the laboratory: wood from seven species of trees grown in the Portuguese forest (Pinus pinaster, Eucalyptus globulus, Quercus suber, Acacia longifolia, Quercus faginea, Olea europaea and Quercus ilex rotundifolia) and briquettes produced from forest biomass waste. Average emission factors were in the ranges 27.5-99.2 g CO kg(-1), 552-1660 g CO(2) kg(-1), 0.66-1.34 g NO kg(-1), and 0.82-4.94 g hydrocarbons kg(-1) of biomass burned (dry basis). Average particle emission factors varied between 1.12 and 20.06 g kg(-1) biomass burned (dry basis), with higher burn rates producing significantly less particle mass per kg wood burned than the low burn rates. Particle mass emission factors from wood-stoves were lower than those from the fireplace. The average emission factors for organic and elemental carbon were in the intervals 0.24-10.1 and 0.18-0.68 g kg(-1) biomass burned (dry basis), respectively. The elemental carbon content of particles emitted from the energy-efficient "chimney type" logwood stove was substantially higher than in the conventional cast iron stove and fireplace, whereas the opposite was observed for the organic carbon fraction. Pinus pinaster, the only softwood species among all, was the biofuel with the lowest emissions of particles, CO, NO and hydrocarbons.

ALTENER - Biomass event in Finland

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

ALTENER - Biomass event in Finland

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

Deashing macroalgae biomass by pulsed electric field treatment.

Science.gov (United States)

Robin, Arthur; Sack, Martin; Israel, Alvaro; Frey, Wolfgang; Müller, Georg; Golberg, Alexander

2018-05-01

Among all biomass constituents, the ashes are major hurdles for biomass processing. Ashes currently have low market value and can make a non-negligible fraction of the biomass dry weight significantly impacting its further processing by degrading equipment, lowering process yield, inhibiting reactions and decreasing products qualities. However, most of the current treatments for deashing biomass are of poor efficiency or industrial relevance. This work is the first report on the use of Pulsed Electric Field (PEF) to enhance deashing of biomass from a high ash content green marine macroalga, Ulva sp., using hydraulic pressing. By inducing cell permeabilization of the fresh biomass, PEF was able to enhance the ash extraction from 18.4% (non-treated control) to 37.4% of the total ash content in average, significantly enhancing the extraction of five of the major ash elements (K, Mg, Na, P and S) compared to pressing alone. Copyright © 2018 Elsevier Ltd. All rights reserved.

Availability of Dutch biomass for electricity and heat in 2020

International Nuclear Information System (INIS)

Koppejan, J.; Elbersen, W.; Meeusen, M.; Bindraban, P.

2009-11-01

Availability of biomass is an important factor in realizing the Dutch targets for renewable energy. This study maps the availability of Dutch biomass in the framework of alternative applications and sustainability requirements, today and in the future. The conclusion is drawn that there is approximately 13 to 16 million tons of dry biomass available for energy generation in the Netherlands in 2020. This is 30 to 40% of the amount of biomass that is annually used in the Netherlands, generating 53 to 94 PJ of final energy, avoiding 101 to 157 PJ of fossil energy. This availability of biomass and the energy that is generated from the biomass can increase further after 2020. In addition, biomass will also be imported, especially for combustion and co-firing in coal-fired power plants and for the production of transport fuels. [nl

Effects of soil type and light on height growth, biomass partitioning, and nitrogen dynamics on 22 species of tropical dry forest tree seedlings: Comparisons between legumes and nonlegumes.

Science.gov (United States)

Smith-Martin, Christina M; Gei, Maria G; Bergstrom, Ellie; Becklund, Kristen K; Becknell, Justin M; Waring, Bonnie G; Werden, Leland K; Powers, Jennifer S

2017-03-01

The seedling stage is particularly vulnerable to resource limitation, with potential consequences for community composition. We investigated how light and soil variation affected early growth, biomass partitioning, morphology, and physiology of 22 tree species common in tropical dry forest, including eight legumes. Our hypothesis was that legume seedlings are better at taking advantage of increased resource availability, which contributes to their successful regeneration in tropical dry forests. We grew seedlings in a full-factorial design under two light levels in two soil types that differed in nutrient concentrations and soil moisture. We measured height biweekly and, at final harvest, biomass partitioning, internode segments, leaf carbon, nitrogen, δ 13 C, and δ 15 N. Legumes initially grew taller and maintained that height advantage over time under all experimental conditions. Legumes also had the highest final total biomass and water-use efficiency in the high-light and high-resource soil. For nitrogen-fixing legumes, the amount of nitrogen derived from fixation was highest in the richer soil. Although seed mass tended to be larger in legumes, seed size alone did not account for all the differences between legumes and nonlegumes. Both belowground and aboveground resources were limiting to early seedling growth and function. Legumes may have a different regeneration niche, in that they germinate rapidly and grow taller than other species immediately after germination, maximizing their performance when light and belowground resources are readily available, and potentially permitting them to take advantage of high light, nutrient, and water availability at the beginning of the wet season. © 2017 Botanical Society of America.

Development of a multicriteria assessment model for ranking biomass feedstock collection and transportation systems.

Science.gov (United States)

Kumar, Amit; Sokhansanj, Shahab; Flynn, Peter C

2006-01-01

This study details multicriteria assessment methodology that integrates economic, social, environmental, and technical factors in order to rank alternatives for biomass collection and transportation systems. Ranking of biomass collection systems is based on cost of delivered biomass, quality of biomass supplied, emissions during collection, energy input to the chain operations, and maturity of supply system technologies. The assessment methodology is used to evaluate alternatives for collecting 1.8 x 10(6) dry t/yr based on assumptions made on performance of various assemblies of biomass collection systems. A proposed collection option using loafer/ stacker was shown to be the best option followed by ensiling and baling. Ranking of biomass transport systems is based on cost of biomass transport, emissions during transport, traffic congestion, and maturity of different technologies. At a capacity of 4 x 10(6) dry t/yr, rail transport was shown to be the best option, followed by truck transport and pipeline transport, respectively. These rankings depend highly on assumed maturity of technologies and scale of utilization. These may change if technologies such as loafing or ensiling (wet storage) methods are proved to be infeasible for large-scale collection systems.

Quality factors, antioxidant activity, and sensory properties of jet-tube dried rabbiteye blueberries.

Science.gov (United States)

Pallas, Laura A; Pegg, Ronald B; Kerr, William L

2013-06-01

Rabbiteye blueberries are an excellent source of nutrients and phytochemicals. They are often dried, which can degrade health-promoting compounds. Means of shortening exposure to high-temperature drying air are desirable. Five cultivars of rabbiteye blueberries ('Premier', 'Tifblue', 'Brightwell', 'Alapaha', and 'Powderblue') were dried in a jet-tube fluidized bed air dryer with varying pretreatments including mechanical abrasion and osmotic dehydration. Drying time ranged from 66 to 95 min at 107 °C, achieving a final water activity of 0.347-0.605. Prior osmotic dehydration significantly reduced the drying time. Vacuum osmotic dehydration for 70 min achieved similar moisture contents to soaking blueberries for 24 h. Jet-tube dried blueberries exhibited greater color saturation than commercially available blueberries. While drying reduced the total monomeric anthocyanin (TMA) content, this occurred to a lesser extent than by other processing methods. The total phenolics content (TPC) and antioxidant capacity (H-ORACFL values) increased after drying. 'Premier' was the most preferred vacuum-infused dried blueberry, with a water activity (aw) of 0.53 and 157 g H2O kg(-1). 'Tifblue' was most preferred amongst the overnight-infused and also unsweetened dried blueberries. Jet-tube drying can substantially reduce drying times while yielding blueberries with good color, sensory properties, TMA, TPC, and H-ORACFL values. Furthermore, some cultivars produce better-quality dried blueberries than others. © 2012 Society of Chemical Industry.

Fungal Waste-Biomasses as Potential Low-Cost Biosorbents for Decolorization of Textile Wastewaters

Directory of Open Access Journals (Sweden)

Antonella Anastasi

2012-10-01

Full Text Available The biosorption potential of three fungal waste-biomasses (Acremonium strictum, Acremonium sp. and Penicillium sp. from pharmaceutical companies was compared with that of a selected biomass (Cunninghamella elegans, already proven to be very effective in dye biosorption. Among the waste-biomasses, A. strictum was the most efficient (decolorization percentage up to 90% within 30 min with regard to three simulated dye baths; nevertheless it was less active than C. elegans which was able to produce a quick and substantial decolorization of all the simulated dye baths (up to 97% within 30 min. The biomasses of A. strictum and C. elegans were then tested for the treatment of nine real exhausted dye baths. A. strictum was effective at acidic or neutral pH, whereas C. elegans confirmed its high efficiency and versatility towards exhausted dye baths characterised by different classes of dyes (acid, disperse, vat, reactive and variation in pH and ionic strength. Finally, the effect of pH on the biosorption process was evaluated to provide a realistic estimation of the validity of the laboratory results in an industrial setting. The C. elegans biomass was highly effective from pH 3 to pH 11 (for amounts of adsorbed dye up to 1054 and 667 mg of dye g−1 biomass dry weight, respectively; thus, this biomass can be considered an excellent and exceptionally versatile biosorbent material.

Termisk forgasning af biomasse

DEFF Research Database (Denmark)

Henriksen, Ulrik Birk

2005-01-01

The title of this Ph.D. thesis is: Thermal Gasification of Biomass. Compilation of activities in the ”Biomass Gasification Group” at Technical University of Denmark (DTU). This thesis gives a presentation of selected activities in the Biomass Gasification Group at DTU. The activities are related...... to thermal gasification of biomass. Focus is on gasification for decentralised cogeneration of heat and power, and on related research on fundamental processes. In order to insure continuity of the presentation the other activities in the group, have also been described. The group was started in the late...... of these activities has been fruitful. The two- stage gasifier was developed for gasification aiming at decentralised cogeneration of heat and power. The development ranged from lap-top scale equipment to a fully automatic plant with more than 2000 hours of operation. Compared to most other gasification processes...

Pre-treatment of oil palm fronds biomass for gasification

Directory of Open Access Journals (Sweden)

Sulaiman Shaharin Anwar

2017-01-01

Full Text Available Oil Palm Fronds (OPF has been proven as one of the potential types of biomass feedstock for power generation. The low ash content and high calorific value are making OPF an attractive source for gasification. The objective of this study is to investigate the effects of pre-treatments of OPF residual on gasification. The pre-treatments included the briquetting process and extensive drying of OPF which are studied separately. In briquetting process, the OPF were mixed with some portions of paper as an additives, leaflets, and water, to form a soupy slurry. The extensive drying of OPF needs to cut down OPF in 4–6 cm particle size and left to dry in the oven at 150°C for 24 hours. Gasification process was carried out at the end of each of the pre-treated processes. It was found that the average gas composition obtained from briquetting process was 8.07%, 2.06%, 0.54%,and 11.02% for CO, H2, CH4, and CO2 respectively. A good composition of syngas was produced from extensive dried OPF, as 16.48%, 4.03%, 0.91%,and 11.15% for CO, H2, CH4, and CO2 contents respectively. It can be concluded that pre-treatments improved the physical characteristics of biomass. The bulk density of biomass can be increased by briquetting but the stability of the structure is depending on the composition of briquette formulation. Furthermore, the stability of gasification process also depended on briquette density, mechanical strength, and formulation.

Biomass equipments. Dryers. Drying, crushing, agglomeration of agro-industrial products; Materiels pour la biomasse. Les secheurs, sechage, broyage, agglomeration de produits agro-industriels

Energy Technology Data Exchange (ETDEWEB)

Deur, O. [Promill (France)

1997-12-31

This paper describes the French Promill Company activity in the design and manufacturing of complete drying-crushing-agglomerating units for agro-industrial products (pulp of beet, lucerne, etc..). The paper focusses on the thermal and mechanical efficiency of the high temperature dryer and on the pulp granulating squeezer. (J.S.)

Simulation of the biomass updraft gasifier

Energy Technology Data Exchange (ETDEWEB)

Teislev, B.

2006-07-15

A consistent (steady state, one-dimensional) mathematical model for a biomass updraft gasifier has been developed based on mass- and energy balances and assuming ideal mixtures of gases and solids. The gases considered are 0{sub 2}, N{sub 2}, H{sub 2}O, CO{sub 2}, H{sub 2}, CO, CH{sub 4} and TAR and the solids are Ash, Carbon, dry Wood and HzO moisture and described by their partial densities in the gasifier bed, together with their axial velocities and temperature. The processes considered are Carbon Oxidation, H{sub 2}0 and CO{sub 2} reduction, the Water Gas Shift process, dry Wood Pyrolysis and Moist Biomass Drying and are described by their temperature and concentration dependant reaction rates. The same mathematical formulation is used throughout the reactor and the methodology used is to solve the resulting 16 partial and algebraic equations (with 16 variables, 8 gaseous partial densities, 4 solids partial densities, 2 velocities and 2 temperatures) in a Newton-Raphson approach using variable length of the integration step. The transition through oxidation and reduction and the passage through the drying zone has been preliminary verified to be in accordance with experimental evidence, but the software developed has not yet been able to describe the transition to pyrolysis and drying and therefore, the final product gas composition from the updraft gasifier has not been verified (apart from verification using a zero-dimensional model). For use in further work an Addendum describing the approach in the form of a 'pseudo code' (including several comments for readers not conversant with the programming language used in the present work - Visual Basic) is included. (au)

Determination of Total Solids and Ash in Algal Biomass: Laboratory Analytical Procedure (LAP)

Energy Technology Data Exchange (ETDEWEB)

Van Wychen, Stefanie; Laurens, Lieve M. L.

2016-01-13

This procedure describes the methods used to determine the amount of moisture or total solids present in a freeze-dried algal biomass sample, as well as the ash content. A traditional convection oven drying procedure is covered for total solids content, and a dry oxidation method at 575 deg. C is covered for ash content.

Compaction and packaging of dry active municipal wastes

International Nuclear Information System (INIS)

Chen Zongming; Xi Xinmin

1994-01-01

The authors present the feature of a compaction system for active municipal wastes and the radiological monitoring results of workplace and environment. A variety of dry active municipal wastes could be compacted by this system. Volume reduction factor attained to 5 to 7 for soft wastes and 8 to 13 for hard wastes. No evident radiological impact was found on workplace and environment

Exergy Steam Drying and Energy Integration

Energy Technology Data Exchange (ETDEWEB)

Verma, Prem; Muenter, Claes (Exergy Engineering and Consulting, SE-417 55 Goeteborg (Sweden)). e-mail: verma@exergyse.com

2008-10-15

Exergy Steam Drying technology has existed for past 28 years and many new applications have been developed during this period. But during past few years the real benefits have been exploited in connection with bio-fuel production and energy integration. The steam dryer consists of a closed loop system, where the product is conveyed by superheated and pressurised carrier steam. The carrier steam is generated by the water vapours from the product being dried, and is indirectly superheated by another higher temperature energy source such as steam, flue gas, thermal oil etc. Besides the superior heat transfer advantages of using pressurised steam as a drying medium, the energy recovery is efficient and simple as the recovered energy (80-90%) is available in the form of steam. In some applications the product quality is significantly improved. Examples presented in this paper: Bio-Combine for pellets production: Through integration of the Exergy Steam Dryer for wood with a combined heat and power (CHP) plant, together with HP steam turbine, the excess carrier steam can be utilised for district heating and/or electrical power production in a condensing turbine. Bio-ethanol production: Both for first and second generation of ethanol can the Exergy process be integrated for treatment of raw material and by-products. Exergy Steam Dryer can dry the distillers dark grains and solubles (DDGS), wood, bagasse and lignin. Bio-diesel production: Oil containing seeds and fruits can be treated in order to improve both the quality of oil and animal feed protein, thus minimizing further oil processing costs and increasing the sales revenues. Sewage sludge as bio-mass: Municipal sewage sludge can be considered as a renewable bio-fuel. By drying and incineration, the combustion heat value of the sludge is sufficient for the drying process, generation of electrical energy and production of district heat. Keywords; Exergy, bio-fuel, bio-mass, pellets, bio-ethanol, biodiesel, bio

Influence of Plot Size on Efficiency of Biomass Estimates in Inventories of Dry Tropical Forests Assisted by Photogrammetric Data from an Unmanned Aircraft System

Directory of Open Access Journals (Sweden)

Daud Jones Kachamba

2017-06-01

Full Text Available Applications of unmanned aircraft systems (UASs to assist in forest inventories have provided promising results in biomass estimation for different forest types. Recent studies demonstrating use of different types of remotely sensed data to assist in biomass estimation have shown that accuracy and precision of estimates are influenced by the size of field sample plots used to obtain reference values for biomass. The objective of this case study was to assess the influence of sample plot size on efficiency of UAS-assisted biomass estimates in the dry tropical miombo woodlands of Malawi. The results of a design-based field sample inventory assisted by three-dimensional point clouds obtained from aerial imagery acquired with a UAS showed that the root mean square errors as well as the standard error estimates of mean biomass decreased as sample plot sizes increased. Furthermore, relative efficiency values over different sample plot sizes were above 1.0 in a design-based and model-assisted inferential framework, indicating that UAS-assisted inventories were more efficient than purely field-based inventories. The results on relative costs for UAS-assisted and pure field-based sample plot inventories revealed that there is a trade-off between inventory costs and required precision. For example, in our study if a standard error of less than approximately 3 Mg ha−1 was targeted, then a UAS-assisted forest inventory should be applied to ensure more cost effective and precise estimates. Future studies should therefore focus on finding optimum plot sizes for particular applications, like for example in projects under the Reducing Emissions from Deforestation and Forest Degradation, plus forest conservation, sustainable management of forest and enhancement of carbon stocks (REDD+ mechanism with different geographical scales.

Feasibility of Biomass Biodrying for Gasification Process

Science.gov (United States)

Hamidian, Arash

An important challenge of biomass gasification is the limitation of feedstock quality especially the moisture content, which plays a significant role on the performance of gasification process. Gasification requires low moisture levels (20% and less) and several reports have emphasized on the moisture as a typical problem while gasifying biomass. Moisture affects overall reaction rates in the gasifiers as a result of temperature drop and ultimately increases tar content, decreases gas yield, changes the composition of produced gas and affects the efficiency. Therefore, it is mandatory to pre-treat the biomass before gasification and reduce the moisture content to the suitable and economic level. The well-known solutions are either natural drying (not practical for commercial plants) or conventional drying technologies (have high operating costs). Biodrying is an alternative process, which uses both convective air and heat of biological reactions as a source of energy, to reduce the moisture. In the biodrying reactor heat is generated from exothermic decomposition of organic fraction of biomass and that is why the process is called "self-heating process". Employing such technology for drying biomass at pre-treatment units of gasification process returns several economic and environmental advantages to mills. In Europe, municipal waste treatment (MSW) plants use the biodrying at commercial scale to degrade a part of the biodegradable fraction of waste to generate heat and reduce the moisture content for high quality SRF (Solid Recovered Fuel) production. In Italy, wine industry is seeking to develop biodrying for energy recovery of grape wastes after fermentation and distillation, which returns economic benefits to the industry. In Canada, the development of biodrying technology for pulp and paper industry was started at Ecole polytechnique de Montreal as an option for sludge management solution. Therefore, batch biodrying reactor was successfully developed in 2004

Biosorption of Cd(II), Ni(II) and Pb(II) from aqueous solution by dried biomass of aspergillus niger: application of response surface methodology to the optimization of process parameters

Energy Technology Data Exchange (ETDEWEB)

Amini, Malihe; Younesi, Habibollah [Department of Environmental Science, Faculty of Natural Resources and Marine Sciences, Tarbiat Modares University, Noor (Iran)

2009-10-15

In this study, the biosorption of Cd(II), Ni(II) and Pb(II) on Aspergillus niger in a batch system was investigated, and optimal condition determined by means of central composite design (CCD) under response surface methodology (RSM). Biomass inactivated by heat and pretreated by alkali solution was used in the determination of optimal conditions. The effect of initial solution pH, biomass dose and initial ion concentration on the removal efficiency of metal ions by A. niger was optimized using a design of experiment (DOE) method. Experimental results indicated that the optimal conditions for biosorption were 5.22 g/L, 89.93 mg/L and 6.01 for biomass dose, initial ion concentration and solution pH, respectively. Enhancement of metal biosorption capacity of the dried biomass by pretreatment with sodium hydroxide was observed. Maximal removal efficiencies for Cd(II), Ni(III) and Pb(II) ions of 98, 80 and 99% were achieved, respectively. The biosorption capacity of A. niger biomass obtained for Cd(II), Ni(II) and Pb(II) ions was 2.2, 1.6 and 4.7 mg/g, respectively. According to these observations the fungal biomass of A. niger is a suitable biosorbent for the removal of heavy metals from aqueous solutions. Multiple response optimization was applied to the experimental data to discover the optimal conditions for a set of responses, simultaneously, by using a desirability function. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

YEAR 2 BIOMASS UTILIZATION

Energy Technology Data Exchange (ETDEWEB)

Christopher J. Zygarlicke

2004-11-01

This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

DYNAMICS OF ALGAE NUMBER AND BIOMASS OF STEPPE BIOGEOCOENOSES AND AGROCOENOSES IN KHERSON REGION

Directory of Open Access Journals (Sweden)

Shcherbina V.V.

2011-12-01

Full Text Available Characteristics of daily dynamics of seaweeds abundance and biomass were determined for steppe biogeocoenosis and agrocoenosis of Biosphere reserve “Askaniya-Nova” in spring of 2011. Fluctuation ranges in seaweeds abundance and biomass have been registered.Analyzing the indices of total number and algae biomass in studied biogeocoenoses it should be noted that the maximal values of alga number in virgin soil steppe exceeded minimal in 3,3 times; biomasses - in 2,1. For virgin soil steppe of post-fire-induced development the relation between maximum and minimal value of total number of algae was up to 2,1; biomass - 2,4. For agrocoenosis we noted the largest ranges in variation of number and biomass. In conditions of dry-land arable land the maximum values of total number of alga exceeded minimal in 21,9 times; biomasses - in 8,7; for irrigated arable land - in 12,5 and 5,6 respectively.In soil samples, selected within the limits of virgin soil biogeocoenoses of biosphere reserve “Askania-Nova” and agrocoenosis of dry-land and irrigated arable land in biosphere reserve by direct count, the algae species of Bacillariophyta, Cyanophyta, Chlorophyta, Xanthophyta and Eustigmatophyta have been found. The largest contribution to number and biomass of algae belonged to Bacillariophyta. The number and biomass of agrocoenosis algae is more dynamic feature, than for algae of virgin soil biogeocoenoses.

Variation of the Phytochemical Constituents and Antioxidant Activities of Zingiber officinale var. rubrum Theilade Associated with Different Drying Methods and Polyphenol Oxidase Activity.

Science.gov (United States)

Ghasemzadeh, Ali; Jaafar, Hawa Z E; Rahmat, Asmah

2016-06-17

The effects of different drying methods (freeze drying, vacuum oven drying, and shade drying) on the phytochemical constituents associated with the antioxidant activities of Z. officinale var. rubrum Theilade were evaluated to determine the optimal drying process for these rhizomes. Total flavonoid content (TFC), total phenolic content (TPC), and polyphenol oxidase (PPO) activity were measured using the spectrophotometric method. Individual phenolic acids and flavonoids, 6- and 8-gingerol and shogaol were identified by ultra-high performance liquid chromatography method. Ferric reducing antioxidant potential (FRAP) and 1,1-diphenyl-2-picrylhydrazyl (DPPH) assays were used for the evaluation of antioxidant activities. The highest reduction in moisture content was observed after freeze drying (82.97%), followed by vacuum oven drying (80.43%) and shade drying (72.65%). The highest TPC, TFC, and 6- and 8-shogaol contents were observed in samples dried by the vacuum oven drying method compared to other drying methods. The highest content of 6- and 8-gingerol was observed after freeze drying, followed by vacuum oven drying and shade drying methods. Fresh samples had the highest PPO activity and lowest content of flavonoid and phenolic acid compounds compared to dried samples. Rhizomes dried by the vacuum oven drying method represent the highest DPPH (52.9%) and FRAP activities (566.5 μM of Fe (II)/g DM), followed by freeze drying (48.3% and 527.1 μM of Fe (II)/g DM, respectively) and shade drying methods (37.64% and 471.8 μM of Fe (II)/g DM, respectively) with IC50 values of 27.2, 29.1, and 34.8 μg/mL, respectively. Negative and significant correlations were observed between PPO and antioxidant activity of rhizomes. Vacuum oven dried rhizomes can be utilized as an ingredient for the development of value-added food products as they contain high contents of phytochemicals with valuable antioxidant potential.

Human impacts on fire occurrence: a case study of hundred years of forest fires in a dry alpine valley in Switzerland

NARCIS (Netherlands)

Zumbrunnen, T.; Menéndez, P.; Bugmann, H.; Conedera, M.; Gimmi, U.; Bürgi, M.

2012-01-01

Forest fire regimes are sensitive to alterations of climate, fuel load, and ignition sources. We investigated the impact of human activities and climate on fire occurrence in a dry continental valley of the Swiss Alps (Valais) by relating fire occurrence to population and road density, biomass

Temperate heath plant response to dry conditions depends on growth strategy and less on physiology

DEFF Research Database (Denmark)

Albert, Kristian Rost; Kongstad, J.; Schmidt, I. K.

2012-01-01

of these differences in response in dry versus rewetting conditions can be used to highlight the limitations coherent in different strategies adopted by, for example, evergreen shrubs and grasses. We investigated the leaf-level photosynthetic performance, leaf C, N and d13C along with vegetation cover and biomass...... in the evergreen dwarf shrub Calluna vulgaris and the grass species Deschampsia flexuosa in a temperate heath during seasonal changes in soil moisture. Higher photosynthetic capacity compensated for lower stomatal conductance and sustained higher rates of photosynthesis in the grass compared to the dwarf shrub....... In combination with dieback of aboveground biomass and reduction of stomatal conductance reduction during dry conditions, the grass continued to have high carbon uptake in the remaining leaves. The dwarf shrub endured the dry conditions by preserving shoot biomass and reducing stomatal conductance. Soil...

An integrated pan-tropical biomass map using multiple reference datasets.

Science.gov (United States)

Avitabile, Valerio; Herold, Martin; Heuvelink, Gerard B M; Lewis, Simon L; Phillips, Oliver L; Asner, Gregory P; Armston, John; Ashton, Peter S; Banin, Lindsay; Bayol, Nicolas; Berry, Nicholas J; Boeckx, Pascal; de Jong, Bernardus H J; DeVries, Ben; Girardin, Cecile A J; Kearsley, Elizabeth; Lindsell, Jeremy A; Lopez-Gonzalez, Gabriela; Lucas, Richard; Malhi, Yadvinder; Morel, Alexandra; Mitchard, Edward T A; Nagy, Laszlo; Qie, Lan; Quinones, Marcela J; Ryan, Casey M; Ferry, Slik J W; Sunderland, Terry; Laurin, Gaia Vaglio; Gatti, Roberto Cazzolla; Valentini, Riccardo; Verbeeck, Hans; Wijaya, Arief; Willcock, Simon

2016-04-01

We combined two existing datasets of vegetation aboveground biomass (AGB) (Proceedings of the National Academy of Sciences of the United States of America, 108, 2011, 9899; Nature Climate Change, 2, 2012, 182) into a pan-tropical AGB map at 1-km resolution using an independent reference dataset of field observations and locally calibrated high-resolution biomass maps, harmonized and upscaled to 14 477 1-km AGB estimates. Our data fusion approach uses bias removal and weighted linear averaging that incorporates and spatializes the biomass patterns indicated by the reference data. The method was applied independently in areas (strata) with homogeneous error patterns of the input (Saatchi and Baccini) maps, which were estimated from the reference data and additional covariates. Based on the fused map, we estimated AGB stock for the tropics (23.4 N-23.4 S) of 375 Pg dry mass, 9-18% lower than the Saatchi and Baccini estimates. The fused map also showed differing spatial patterns of AGB over large areas, with higher AGB density in the dense forest areas in the Congo basin, Eastern Amazon and South-East Asia, and lower values in Central America and in most dry vegetation areas of Africa than either of the input maps. The validation exercise, based on 2118 estimates from the reference dataset not used in the fusion process, showed that the fused map had a RMSE 15-21% lower than that of the input maps and, most importantly, nearly unbiased estimates (mean bias 5 Mg dry mass ha(-1) vs. 21 and 28 Mg ha(-1) for the input maps). The fusion method can be applied at any scale including the policy-relevant national level, where it can provide improved biomass estimates by integrating existing regional biomass maps as input maps and additional, country-specific reference datasets. © 2015 John Wiley & Sons Ltd.

Characterization of Various Biomass Feedstocks for Energy Production

DEFF Research Database (Denmark)

Toor, Saqib; Rosendahl, Lasse; Hoffmann, Jessica

2013-01-01

Biomass represents the renewable energy source and their use reduces the consumption of fossil fuels and limits the emission of CO2. In this work, various biomass feedstocks were assessed for assessing their suitability as energy production sources using thermochemical conversion routes especially...... hydrothermal liquefaction (HTL) process. The methods used to analyze involved performing proximate, ultimate and thermogravimetry analysis. On the basis of proximate, ultimate, and thermogravimetry analysis, the dried distiller grains with solubles (DDGS), corn silage, chlorella vulgaris, spirulina platensis...

Influence of prevailing disturbances on soil biology and biochemistry of montane habitats at Nanda Devi Biosphere Reserve, India during wet and dry seasons

DEFF Research Database (Denmark)

Singh, S.K.; Singh, Anoop; Rai, J.P.N.

2011-01-01

The impact of prevailing disturbances in montane habitats of Nanda Devi Biosphere Reserve (NDBR) was studied on soil microbial population, biomass, soil respiration and enzyme activities during wet and dry seasons. The physico-chemical characteristics of soils exhibited conspicuous variation in t...

Biomass resilience of Neotropical secondary forests.

Science.gov (United States)

Poorter, Lourens; Bongers, Frans; Aide, T Mitchell; Almeyda Zambrano, Angélica M; Balvanera, Patricia; Becknell, Justin M; Boukili, Vanessa; Brancalion, Pedro H S; Broadbent, Eben N; Chazdon, Robin L; Craven, Dylan; de Almeida-Cortez, Jarcilene S; Cabral, George A L; de Jong, Ben H J; Denslow, Julie S; Dent, Daisy H; DeWalt, Saara J; Dupuy, Juan M; Durán, Sandra M; Espírito-Santo, Mario M; Fandino, María C; César, Ricardo G; Hall, Jefferson S; Hernandez-Stefanoni, José Luis; Jakovac, Catarina C; Junqueira, André B; Kennard, Deborah; Letcher, Susan G; Licona, Juan-Carlos; Lohbeck, Madelon; Marín-Spiotta, Erika; Martínez-Ramos, Miguel; Massoca, Paulo; Meave, Jorge A; Mesquita, Rita; Mora, Francisco; Muñoz, Rodrigo; Muscarella, Robert; Nunes, Yule R F; Ochoa-Gaona, Susana; de Oliveira, Alexandre A; Orihuela-Belmonte, Edith; Peña-Claros, Marielos; Pérez-García, Eduardo A; Piotto, Daniel; Powers, Jennifer S; Rodríguez-Velázquez, Jorge; Romero-Pérez, I Eunice; Ruíz, Jorge; Saldarriaga, Juan G; Sanchez-Azofeifa, Arturo; Schwartz, Naomi B; Steininger, Marc K; Swenson, Nathan G; Toledo, Marisol; Uriarte, Maria; van Breugel, Michiel; van der Wal, Hans; Veloso, Maria D M; Vester, Hans F M; Vicentini, Alberto; Vieira, Ima C G; Bentos, Tony Vizcarra; Williamson, G Bruce; Rozendaal, Danaë M A

2016-02-11

Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates are influenced by climate, landscape, and prior land use. Here we analyse aboveground biomass recovery during secondary succession in 45 forest sites and about 1,500 forest plots covering the major environmental gradients in the Neotropics. The studied secondary forests are highly productive and resilient. Aboveground biomass recovery after 20 years was on average 122 megagrams per hectare (Mg ha(-1)), corresponding to a net carbon uptake of 3.05 Mg C ha(-1) yr(-1), 11 times the uptake rate of old-growth forests. Aboveground biomass stocks took a median time of 66 years to recover to 90% of old-growth values. Aboveground biomass recovery after 20 years varied 11.3-fold (from 20 to 225 Mg ha(-1)) across sites, and this recovery increased with water availability (higher local rainfall and lower climatic water deficit). We present a biomass recovery map of Latin America, which illustrates geographical and climatic variation in carbon sequestration potential during forest regrowth. The map will support policies to minimize forest loss in areas where biomass resilience is naturally low (such as seasonally dry forest regions) and promote forest regeneration and restoration in humid tropical lowland areas with high biomass resilience.

River discharge as a major driving force on spatial and temporal variations in zooplankton biomass and community structure in the Godavari estuary India.

Science.gov (United States)

Venkataramana, V; Sarma, V V S S; Matta Reddy, Alavala

2017-08-28

Variability in horizontal zooplankton biomass distribution was investigated over 13 months in the Godavari estuary, along with physical (river discharge, temperature, salinity), chemical (nutrients, particulate organic matter), biological (phytoplankton biomass), and geological (suspended matter) properties to examine the influencing factors on their spatial and temporal variabilities. The entire estuary was filled with freshwater during peak discharge period and salinity near zero, increased to ~ 34 psu during dry period with relatively high nutrient levels during former than the latter period. Due to low flushing time ( 500 mg L -1 ) during peak discharge period, picoplankton (cyanophyceae) contributed significantly to the phytoplankton biomass (Chl-a) whereas microplankton and nanoplankton (bacillariophyceae, and chlorophyceae) during moderate and mostly microplankton during dry period. Zooplankton biomass was the lowest during peak discharge period and increased during moderate followed by dry period. The zooplankton abundance was controlled by dead organic matter during peak discharge period, while both phytoplankton biomass and dead organic matter during moderate discharge and mostly phytoplankton biomass during dry period. This study suggests that significant modification of physico-chemical properties by river discharge led to changes in phytoplankton composition and dead organic matter concentrations that alters biomass, abundance, and composition of zooplankton in the Godavari estuary.

Changes in Soil Enzyme Activities and Microbial Biomass after Revegetation in the Three Gorges Reservoir, China

Directory of Open Access Journals (Sweden)

Qingshui Ren

2018-05-01

Full Text Available Soil enzymes and microbes are central to the decomposition of plant and microbial detritus, and play important roles in carbon, nitrogen, and phosphorus biogeochemistry cycling at the ecosystem level. In the present study, we characterized the soil enzyme activity and microbial biomass in revegetated (with Taxodium distichum (L. Rich. and Cynodon dactylon (L. Pers. versus unplanted soil in the riparian zone of the Three Gorges Dam Reservoir (TGDR, in order to quantify the effect of revegetation on the edaphic microenvironment after water flooding in situ. After revegetation, the soil physical and chemical properties in revegetated soil showed significant differences to those in unplanted soil. The microbial biomass carbon and phosphorus in soils of T. distichum were significantly higher than those in C. dactylon and unplanted soils, respectively. The microbial biomass nitrogen in revegetated T. distichum and C. dactylon soils was significantly increased by 273% and 203%, respectively. The enzyme activities of T. distichum and C. dactylon soils displayed no significant difference between each other, but exhibited a great increase compared to those of the unplanted soil. Elements ratio (except C/N (S did not vary significantly between T. distichum and C. dactylon soils; meanwhile, a strong community-level elemental homeostasis in the revegetated soils was found. The correlation analyses demonstrated that only microbial biomass carbon and phosphorus had a significantly positive relationship with soil enzyme activities. After revegetation, both soil enzyme activities and microbial biomasses were relatively stable in the T. distichum and C. dactylon soils, with the wooded soil being more superior. The higher enzyme activities and microbial biomasses demonstrate the C, N, and P cycling and the maintenance of soil quality in the riparian zone of the TGDR.

Hydrothermal conversion of biomass to liquid energy sources; Hydrothermale Konversion von Biomasse zu fluessigen Energietraegern

Energy Technology Data Exchange (ETDEWEB)

Kroeger, Michael; Peters, Mario; Klemm, Marco; Nelles, Michael [Deutsches Biomasseforschungszentrum (DBFZ) gemeinnuetzige GmbH, Leipzig (Germany)

2013-10-01

Beside thermo-chemical processes like pyrolysis, torrefaction and gasification another process group called hydrothermal conversion of biomass comes into the focus of research and development. Especially for wet biomass this process has several advantages: as the reaction medium is water wet biomass not needs to be dried. Beside the reaction pathways, which are still not completely understood, it is important to investigate reactor concepts. That gives the possibility to continuously process the given biomass to deduce specific process conditions for the production of chemicals and fuels. Experiments were conducted in a newly developed tubular reactor at temperatures from 150 to 270 C and reaction times from 1 to 6 min. By studying the HPLC analysis of the liquid products the formation and degradation of several products which may be utilized as base materials for chemicals and fuels (furfural, 5-HMF etc.) was conducted. The experiments illustrate the possibility to influence product composition to a certain extend only by varying temperature and time of the hydrothermal process. That could result in an economic and feasible way to produce intermediate chemicals from biomass. In a second step these product analysis will be used to develop catalysts and investigate the possibilities of in-situ-hydrogenation and synthesis of further valuable chemicals and fuels. (orig.)

Soil fungal and bacterial biomass determined by epifluorescence microscopy and mycorrhizal spore density in different sugarcane managements

Directory of Open Access Journals (Sweden)

Adriana Pereira Aleixo

2014-04-01

Full Text Available Crop productivity and sustainability have often been related to soil organic matter and soil microbial biomass, especially because of their role in soil nutrient cycling. This study aimed at measuring fungal and bacterial biomass by epifluorescence microscopy and arbuscular mycorrhizal fungal (AMF spore density in sugarcane (Saccharum officinarum L. fields under different managements. We collected soil samples of sugarcane fields managed with or without burning, with or without mechanized harvest, with or without application of vinasse and from nearby riparian native forest. The soil samples were collected at 10cm depth and storage at 4°C until analysis. Fungal biomass varied from 25 to 37µg C g-1 dry soil and bacterial from 178 to 263µg C g-1 dry soil. The average fungal/bacterial ratio of fields was 0.14. The AMF spore density varied from 9 to 13 spores g-1 dry soil. The different sugarcane managements did not affect AMF spore density. In general, there were no significant changes of microbial biomass with crop management and riparian forest. However, the sum of fungal and bacterial biomass measured by epifluorescence microscopy (i.e. 208-301µg C g-1 dry soil was very close to values of total soil microbial biomass observed in other studies with traditional techniques (e.g. fumigation-extraction. Therefore, determination of fungal/bacterial ratios by epifluorescence microscopy, associated with other parameters, appears to be a promising methodology to understand microbial functionality and nutrient cycling under different soil and crop managements.

Simulation of biomass pneumatic drying with ascending swirling movement

International Nuclear Information System (INIS)

Bombino Matos, Eugenio F.; Pineda Revilla, Edel

2017-01-01

Considering the layer form acquired by the particles during the studying process it was necessary to define the relation cheap between the heat and mass transfer area and particles flow to simulate with more precision this kind of drying. The simulations results were compared, by a statistical analysis based in Statgraphics-Centurion V15 program, with the results obtained in others pneumatic bagasse dryers studies and were similar and for that reason it was categorical that is correct the definition made about the relation cheap area/material flow defined in this work and it’s possible to reduce pneumatic dryer height by using this method. This reduction that can be seen by the Height Reduction Sing (HRS) of the drying column, defined in the work, will permit more compact dryers. (author)

Biomass - Overview of Swiss Research Programme 2003; Biomasse

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D.; Guggisberg, B.

2003-07-01

This overview for the Swiss Federal Office of Energy (SFOE) discusses the results obtained in 2003 in various research projects worked on in Switzerland on the subject of biomass. In the biomass combustion area, subjects discussed include system optimisation for automatic firing, combustion particles, low-particle pellet furnaces, design and optimisation of wood-fired storage ovens, efficiency of filtering techniques and methane generation from wood. Also, an accredited testing centre for wood furnaces is mentioned and measurements made on an installation are presented. As far as the fermentation of biogenic wastes is concerned, biogas production from dairy-product wastes is described. Other projects discussed include a study on eco-balances of energy products, certification and marketing of biogas, evaluation of membranes, a measurement campaign for solar sludge-drying, the operation of a percolator installation for the treatment of bio-wastes, the effects of compost on the environment and the fermentation of coffee wastes. Also, statistics on biogas production in 2002 is looked at. Finally, a preliminary study on biofuels is presented.

Effect of emulsification and spray-drying microencapsulation on the antilisterial activity of transcinnamaldehyde.

Science.gov (United States)

Trinh, Nga-Thi-Thanh; Lejmi, Raja; Gharsallaoui, Adem; Dumas, Emilie; Degraeve, Pascal; Thanh, Mai Le; Oulahal, Nadia

2015-01-01

Spray-dried redispersible transcinnamaldehyde (TC)-in-water emulsions were prepared in order to preserve its antibacterial activity; 5% (w/w) TC emulsions were first obtained with a rotor-stator homogeniser in the presence of either soybean lecithin or sodium caseinate as emulsifiers. These emulsions were mixed with a 30% (w/w) maltodextrin solution before feeding a spray-dryer. The antibacterial activity of TC alone, TC emulsions with and without maltodextrin before and after spray-drying were assayed by monitoring the growth at 30 °C of Listeria innocua in their presence and in their absence (control). Whatever the emulsifier used, antilisterial activity of TC was increased following its emulsification. However, reconstituted spray-dried emulsions stabilised by sodium caseinate had a higher antibacterial activity suggesting that they better resisted to spray-drying. This was consistent with observation that microencapsulation efficiencies were 27.6% and 78.7% for emulsions stabilised by lecithin and sodium caseinate, respectively.

Spatial and temporal distribution of tropical biomass burning

Science.gov (United States)

Hao, Wei Min; Liu, Mei-Huey

1994-12-01

A database for the spatial and temporal distribution of the amount of biomass burned in tropical America, Africa, and Asia during the late 1970s is presented with a resolution of 5° latitude × 5° longitude. The sources of burning in each grid cell have been quantified. Savanna fires, shifting cultivation, deforestation, fuel wood use, and burning of agricultural residues contribute about 50, 24, 10, 11, and 5%, respectively, of total biomass burned in the tropics. Savanna fires dominate in tropical Africa, and forest fires dominate in tropical Asia. A similar amount of biomass is burned from forest and savanna fires in tropical America. The distribution of biomass burned monthly during the dry season has been derived for each grid cell using the seasonal cycles of surface ozone concentrations. Land use changes during the last decade could have a profound impact on the amount of biomass burned and the amount of trace gases and aerosol particles emitted.

Waste activated sludge fermentation: effect of solids retention time and biomass concentration.

Science.gov (United States)

Yuan, Q; Sparling, R; Oleszkiewicz, J A

2009-12-01

Laboratory scale, room temperature, semi-continuous reactors were set-up to investigate the effect of solids retention time (SRT, equal to HRT hydraulic retention time) and biomass concentration on generation of volatile fatty acids (VFA) from the non-methanogenic fermentation of waste activated sludge (WAS) originating from an enhanced biological phosphorus removal process. It was found that VFA yields increased with SRT. At the longest SRT (10d), improved biomass degradation resulted in the highest soluble to total COD ratio and the highest VFA yield from the influent COD (0.14g VFA-COD/g TCOD). It was also observed that under the same SRT, VFA yields increased when the biomass concentration decreased. At a 10d SRT the VFA yield increased by 46%, when the biomass concentration decreased from 13g/L to 4.8g/L. Relatively high nutrient release was observed during fermentation. The average phosphorus release was 17.3mg PO(4)-P/g TCOD and nitrogen release was 25.8mg NH(4)-N/g TCOD.

Bacterial diversity and active biomass in full-scale granular activated carbon filters operated at low water temperatures.

Science.gov (United States)

Kaarela, Outi E; Härkki, Heli A; Palmroth, Marja R T; Tuhkanen, Tuula A

2015-01-01

Granular activated carbon (GAC) filtration enhances the removal of natural organic matter and micropollutants in drinking water treatment. Microbial communities in GAC filters contribute to the removal of the biodegradable part of organic matter, and thus help to control microbial regrowth in the distribution system. Our objectives were to investigate bacterial community dynamics, identify the major bacterial groups, and determine the concentration of active bacterial biomass in full-scale GAC filters treating cold (3.7-9.5°C), physicochemically pretreated, and ozonated lake water. Three sampling rounds were conducted to study six GAC filters of different operation times and flow modes in winter, spring, and summer. Total organic carbon results indicated that both the first-step and second-step filters contributed to the removal of organic matter. Length heterogeneity analysis of amplified 16S rRNA genes illustrated that bacterial communities were diverse and considerably stable over time. α-Proteobacteria, β-Proteobacteria, and Nitrospira dominated in all of the GAC filters, although the relative proportion of dominant phylogenetic groups in individual filters differed. The active bacterial biomass accumulation, measured as adenosine triphosphate, was limited due to low temperature, low flux of nutrients, and frequent backwashing. The concentration of active bacterial biomass was not affected by the moderate seasonal temperature variation. In summary, the results provided an insight into the biological component of GAC filtration in cold water temperatures and the operational parameters affecting it.

Effects of Drying Methods in Gaining of Extractive, Phenolic Content and Antioxidant Activity in Gynura Pseudochina (Lour.)

OpenAIRE

Rivai, Harrizul; Nurdin, Hazli; Suyani, Hamzar; Bakhtiar, Amri

2010-01-01

Effects of drying methods in gaining of extractive, phenolic content and antioxidant activity in Gynura pseudochina (Lour.) DC leaves have been investigated. The drying methods tested were air-drying at ± 25 oC, oven-drying at 40 OC, oven-drying at 60 OC, microwave oven-drying and fresh samples as control. Results revealed that drying of the fresh plant caused the decrease of extractive obtainability, phenolic content and antioxidant activity. There were significant differences among drying ...

Improved energy efficiency in sawmill drying system

International Nuclear Information System (INIS)

Anderson, Jan-Olof; Westerlund, Lars

2014-01-01

Highlights: • A heating system at a sawmill was investigated and improved. • Different impacts of external technologies at the energy usage were explored. • The heat and electricity consumption was analysed separate between technologies type. • The result point out a significant decrease of the biomass consumptions. - Abstract: The worldwide use of biomass has increased drastically during the last decade. At Swedish sawmills about half of the entering timber becomes lumber, with the remainder considered as by-product (biomass). A significant part of this biomass is used for internal heat production, mainly for forced drying of lumber in drying kilns. Large heat losses in kilns arise due to difficulties in recovering evaporative heat in moist air at low temperatures. This paper addresses the impact of available state-of-the-art technologies of heat recycling on the most common drying schemes used in Swedish sawmills. Simulations of different technologies were performed on an hourly basis to compare the heat and electricity demand with the different technologies. This was executed for a total sawmill and finally to the national level to assess the potential effects upon energy efficiency and biomass consumption. Since some techniques produce a surplus of heat the comparison has to include the whole sawmill. The impact on a national level shows the potential of the different investigated techniques. The results show that if air heat exchangers were introduced across all sawmills in Sweden, the heat demand would decrease by 0.3 TWh/year. The mechanical heat pump technology would decrease the heat demand by 5.6 TWh/year and would also produce a surplus for external heat sinks, though electricity demand would increase by 1 TWh/year. The open absorption system decreases the heat demand by 3.4 TWh/year on a national level, though at the same time there is a moderate increase in electricity demand of 0.05 TWh/year. Introducing actual energy prices in Sweden gives an

Simulation of the biomass updraft gasifier

Energy Technology Data Exchange (ETDEWEB)

Teislev, B.

2006-07-15

A consistent (steady state, one-dimensional) mathematical model for a biomass updraft gasifier has been developed based on mass- and energy balances and assuming ideal mixtures of gases and solids. The gases considered are 0{sub 2}, N{sub 2}, H{sub 2}0, CO{sub 2}, H{sub 2}, CO, CH{sub 4} and TAR and the solids are Ash, Carbon, dry Wood and H{sub 2}O moisture and described by their partial densities in the gasifier bed - together with their axial velocities and temperature. The processes considered are Carbon Oxidation, H{sub 2}0 and CO{sub 2} reduction, the Water Gas Shift process, dry Wood Pyrolysis and Moist Biomass Drying and are described by their temperature and concentration dependant reaction rates. The same mathematical formulation is used throughout the reactor and the methodology used is to solve the resulting 16 partial and algebraic equations (with 16 variables - 8 gaseous partial densities, 4 solids partial densities, 2 velocities and 2 temperatures) in a Newton-Raphson approach using variable length of the integration step. The transition through oxidation and reduction and the passage through the drying zone has been preliminary verified to be in accordance with experimental evidence, but the software developed has not yet been able to describe the transition to pyrolysis and drying and therefore, the final product gas composition from the updraft gasifier has not been verified (apart from verification using a zero-dimensional model). For use in further work an Addendum describing the approach in the form of a 'pseudo code' (including several comments for readers not conversant with the programming language used in the present work - Visual Basic) is included. (au)

Optimisation and significance of ATP analysis for measuring active biomass in granular activated carbon filters used in water treatment

NARCIS (Netherlands)

Magic-Knezev, A.; Kooij, van der D.

2004-01-01

A method for determining the concentration of active microbial biomass in granular activated carbon (GAC) filters used in water treatment was developed to facilitate studies on the interactions between adsorption processes and biological activity in such filters. High-energy sonication at a power

The Influence of Different Air-Drying Conditions on Bioactive Compounds and Antioxidant Activity of Berries.

Science.gov (United States)

Bustos, Mariela C; Rocha-Parra, Diego; Sampedro, Ines; de Pascual-Teresa, Sonia; León, Alberto E

2018-03-21

The aim of the present research was to study the effect of convective drying on color, bioactive compounds, and antioxidant activity of berry fruits and to chemically characterize the polyphenolic composition of raspberry, boysenberry, redcurrants, and blackcurrants fruit. Drying berries at 65 °C provoked the best conservations of color, particularly for boysenberry and blackcurrant. Drying at 65 °C was also the condition that showed higher level of polyphenols, while drying at 50 or 130 °C showed above % degradation of them due to the long time or high temperature drying. Radical scavenging activity was the predominant antioxidant mechanism in all samples, with 65 °C dried berries being the most active ones possibly because of polyphenol depolymerization. The anthocyanin profile showed that delphinidin and cyanidin derivatives were the most abundant anthocyanidins with different predominance between berry genera. Degradation of anthocyanins was increased with drying temperature been Cy 3-glucoside and Cy 3-rutinoside the most abundant.

Catalytic hydrothermal gasification of biomass for the production of synthetic natural gas[Dissertation 17100

Energy Technology Data Exchange (ETDEWEB)

Waldner, M H

2007-07-01

operating plant on a laboratory scale (throughput 1 kg/hr, which yields about 200 L{sub SNG}/hr with a thermal heating power of 1 kW{sub th} for a feed concentration of 40 wt %). Ideally, the pilot plant should be capable of conveying solid containing slurries. Various catalysts were selected (some of them were synthesized in-house) and tested for their stability under hydrothermal conditions and for their tolerance towards inorganic salts (sulfate was chosen as model substance for these tests). The catalysts were characterized by numerous techniques (such as TG/FTIR, TPO/TPR, TOC, BET, XRD, XPS, ICP, TEM, HAADF-STEM, and SEM-EDXS). The biomass was analyzed for its constituents in order to get a reliable estimate of its energy content, which is essential for the calculation of the process economics. The lower heating value of concentrated swine manure was found to be 16.3 MJ/kg{sub dry} {sub matter}. Skeletal nickel catalysts, which are widely used in the industry due to their attractive price, gasified wood suspensions (conc. 10 - 30 wt %) in a batch reactor completely to SNG. The methane yield was 0.33 g{sub CH{sub 4}}/ g{sub wood,} {sub dry}, which corresponds to the maximum yield governed by thermodynamics. Manure suspensions were also gasified in the hydrothermal environment. The highest methane yield achieved was only 0.21 g{sub CH{sub 4}}/ g{sub dry,} {sub matter}, which is 80% of the maximum yield by thermodynamics. The reason for this were the salts present in the manure, which had not been separated before the experiments and caused the deactivation of the catalyst. Thus, the importance of an integrated salt separator in a demonstration plant cannot be emphasized enough. The most promising catalyst systems (nickel, ruthenium) were tested for their activity and stability in the hydrothermal environment in a continuously operating test rig, where due to the applied pump only liquids could be fed. A mixture of five organic substances (formic and acetic acid, ethanol

Biomass production by Coffea canephora Pierre ex Froehner in two productives cycles

International Nuclear Information System (INIS)

Bustamante González, Carlos; Rodríguez, Maritza I.; Pérez Díaz, Alberto; Viñals, Rolando; Martín Alonso, Gloria M.; Rivera, Ramón

2015-01-01

In areas of the Estación Central de Investigaciones de Café y Cacao located in La Mandarina, Tercer Frente municipality, Santiago de Cuba province, and La Alcarraza, municipality Sagua de Tánamo, Holguín province, the biomass production of Coffea canephora Pierre ex Froehner var. Robusta was assessed from planting until the fourth year in both locations and after pruning until the fourth year in Alcarraza. The coffee trees were planted at 3 x 1,5 m in Cambisol under Samanea saman Jerr shade in the first town and Leucaena leucocephala Lam de Wit in the second. The biomass was separated into: leaves, branches, stems, fruits and roots. From 24 months and one year after pruning, leaflitter was collected monthly. For the study of the root system soil blocks of 25 x 25 x 25 cm were extracted, in an area formed by 1,5 m (distance to the street) and 0,75 m (between plants), centered relative to the coffee plant and up to a meter deep. The extracted soil represented ¼ of the volume occupied by the plant. The dry mass of each organ was determined. Dry matter production reached values of 25 t dry mass ha-1 regardless of the stage of the plantation. Until the fourth year the root system dominated the biomass, followed by the leaves and then the stems. The participation of the fruits in the biomass increased in the crop stage and when concluding the experiment the coffees had dedicated for its formation among the 16-20 % of the total dry mass, independently of the development cycle. (author)

Influence of different anoxic time exposures on active biomass, protozoa and filamentous bacteria in activated sludge.

Science.gov (United States)

Rodriguez-Perez, S; Fermoso, F G; Arnaiz, C

Medium-sized wastewater treatment plants are considered too small to implement anaerobic digestion technologies and too large for extensive treatments. A promising option as a sewage sludge reduction method is the inclusion of anoxic time exposures. In the present study, three different anoxic time exposures of 12, 6 and 4 hours have been studied to reduce sewage sludge production. The best anoxic time exposure was observed under anoxic/oxic cycles of 6 hours, which reduced 29.63% of the biomass production compared with the oxic control conditions. The sludge under different anoxic time exposures, even with a lower active biomass concentration than the oxic control conditions, showed a much higher metabolic activity than the oxic control conditions. Microbiological results suggested that both protozoa density and abundance of filamentous bacteria decrease under anoxic time exposures compared to oxic control conditions. The anoxic time exposures 6/6 showed the highest reduction in both protozoa density, 37.5%, and abundance of filamentous bacteria, 41.1%, in comparison to the oxic control conditions. The groups of crawling ciliates, carnivorous ciliates and filamentous bacteria were highly influenced by the anoxic time exposures. Protozoa density and abundance of filamentous bacteria have been shown as promising bioindicators of biomass production reduction.

Allometric equations for estimating standing biomass of Avicennia marina in Bushehr of Iran

Directory of Open Access Journals (Sweden)

Akbar Ghasemi

2016-07-01

Full Text Available Today, it is important to use of ecological indicators, such as biomass for recognizing the special status of ecosystems, such as mangrove forests and also monitoring and evaluating changes through a specific period. Because using the direct method of evaluating biomass would be destructive, it is common in all similar area to use determine exact Allometric equations by using the statistical relationship between the structural characteristics of trees and their biomass and use these equations to estimate the biomass of trees. The aim of this study is estimate the aboveground biomass of mangroves and determine Allometric models for Nayband area in Bushehr, located in southern Iran. A number of mangrove trees were randomly selected. Collar diameter, crown diameter and tree height of standing trees were measured. After logging and weighing fresh weight, dry weight, trunk and branches were obtained in laboratory and biomass of components was calculated. The relationship between quantities feature of trees and biomass for determination of allometric equation was studied by using linear, power and exponential regression. The equations were compared with each other based on the different modeling parameters. The highest significant correlation was found between crown diameters and dry weight (R > 0.90. The best equations were obtained by means of an exponential and power regression models (R2adj> 0.90. The models were obtained from explained factor, suggests that there might be a relationship between the characteristics of mangrove trees and biomass.

Effects of Different Drying Methods on the Antioxidant Activities of Leaves and Berries of Cayratia trifolia

International Nuclear Information System (INIS)

Rabeta, M.S.; Lin, S.P.

2015-01-01

This study aimed to assess the effects of fresh, thermal drying method (vacuum oven drying), and nonthermal drying method (freeze drying) on the antioxidant activities of leaves and berries of Cayratia trifolia using ferric reducing antioxidant power (FRAP) and 1,1-diphenyl-1-picrylhydrazyl radical scavenging capacity (DPPH) assays. The total phenolic content (TPC) and flavonoid content (TFC) of the leaves and berries of C. trifolia were also measured. Based on the results obtained, the TPC, TFC, and antioxidant activities of the leaves and berries were arranged in the following order: freeze-dried sample with methanol extraction > vacuum-dried sample with methanol extraction > freeze-dried sample with water extraction > vacuum-dried sample with water extraction > fresh sample with methanol extraction > fresh sample with water extraction. The results showed a significant difference (p<0.05) between the fresh and dried samples. In conclusion, freeze drying was found to be a good method for maintaining TPC, TFC, and antioxidant activities by FRAP and DPPH methods in the leaves and berries of C. trifolia. (author)

Comparison of different drying methods on the physical properties, bioactive compounds and antioxidant activity of raspberry powders.

Science.gov (United States)

Si, Xu; Chen, Qinqin; Bi, Jinfeng; Wu, Xinye; Yi, Jianyong; Zhou, Linyan; Li, Zhaolu

2016-04-01

Dehydration has been considered as one of the traditional but most effective techniques for perishable fruits. Raspberry powders obtained after dehydration can be added as ingredients into food formulations such as bakery and dairy products. In this study, raspberry powders obtained by hot air drying (HAD), infrared radiation drying (IRD), hot air and explosion puffing drying (HA-EPD), infrared radiation and microwave vacuum drying (IR-MVD) and freeze drying (FD) were compared on physical properties, bioactive compounds and antioxidant activity. Drying techniques affected the physical properties, bioactive compounds and antioxidant activity of raspberry powders greatly. FD led to significantly higher (P drying methods. However, thermal drying techniques, especially combined drying methods, were superior to FD in final total polyphenol content, total flavonoid content and antioxidant activity. The combined drying methods, especially IR-MVD, showed the highest total polyphenol content (123.22 g GAE kg(-1) dw) and total flavonoid content (0.30 g CAE kg(-1) dw). Additionally, IR-MVD performed better in antioxidant activity retention. Overall, combined drying methods, especially IR-MVD, were found to result in better quality of raspberry powders among the thermal drying techniques. IR-MVD could be recommended for use in the drying industry because of its advantages in time saving and nutrient retention. © 2015 Society of Chemical Industry.

Determination of effective moisture diffusivity and drying kinetics for poplar sawdust by thermogravimetric analysis under isothermal condition.

Science.gov (United States)

Chen, Dengyu; Zheng, Yan; Zhu, Xifeng

2012-03-01

The current study presents a thermogravimetric method to determine the effective moisture diffusivity and drying kinetics of biomass. Drying experiments on poplar sawdust were performed at four temperatures (60, 70, 80, and 90°C) by a thermogravimetric analyzer (TGA). The major assumption in experimentally determining effective diffusivity by Fick's diffusion equation is that drying is mass transfer limited and temperature remains isothermal during drying. The results indicated that TGA could well achieve these determining conditions. The drying process of sawdust mostly took place in the falling rate period. Midilli-Kucuk model showed the best fit for all experimental data. The effective diffusivity values changed from 9.38 × 10(-10)m(2)/s to 1.38 × 10(-9)m(2)/s within the given temperature range, and the activation energy was calculated to be 12.3 kJ/mol. Copyright © 2011 Elsevier Ltd. All rights reserved.

Efficient biomass preparation for the utilization as biocoal in industrial applications

Energy Technology Data Exchange (ETDEWEB)

Lampe, Karl; Grund, Guido; Erpelding, Richard; Denker, Jurgen [ThyssenKrupp Polysius AG, Beckum (Germany)

2012-11-01

Rising energy costs and regulations on the efficient utilisation of energy resources force plant operators in all industrial sectors to focus on these aspects. Both in power generation as well as in thermal processes, the use of renewable sources is becoming more and more important. In this respect, especially the utilisation of biomass plays an ever-increasing role. The production of biocoal offers a solution to overcome the challenges of a wide range of different feedstock properties and to provide homogenised, biogenic fuels. The main objectives to be achieved in biocoal production are efficient drying, energy densification, bulk density maximisation and grindability optimisation. Here, the torrefaction of biomass presents a suitable and energy-efficient solution. With regard to uniform temperature distribution, temperature control, efficiency and final product quality, the multiple hearth furnace method is the preferred process of ThyssenKrupp Polysius. A double-zone multiple hearth furnace (POLTORR) permits both drying and torrefaction of wet biomasses up to 50% moisture content in one coupled unit. The main advantage of this process is the direct, safe and efficient utilisation of the volatiles released during torrefaction for the drying process by means of post-combustion, thus under favourable conditions, an almost autothermic process can be realized.

Radioactivity evaluation method for pre-packed concrete packages of low-level dry active wastes

International Nuclear Information System (INIS)

Sakai, Toshiaki; Funahashi, Tetsuo; Watabe, Kiyomi; Ozawa, Yukitoshi; Kashiwagi, Makoto

1998-01-01

Low-level dry active wastes of nuclear power plants are grouted with cement mortal in a container and planned to disposed into the shallow land disposal site. The characteristics of radionuclides contained in dry active wastes are same as homogeneous solidified wastes. In the previous report, we reported the applicability of the radioactivity evaluation methods established for homogeneous solidified wastes to pre-packed concrete packages. This report outlines the developed radioactivity evaluation methods for pre-packed concrete packages based upon recent data. Since the characteristics of dry active wastes depend upon the plant system in which dry active wastes originate and the types of contamination, sampling of wastes and activity measurement were executed to derive scaling factors. The radioactivity measurement methods were also verified. The applicability of non-destructive methods to measure radioactivity concentration of pre-packed concrete packages was examined by computer simulation. It is concluded that those methods are accurate enough to measure actual waste packages. (author)

Estimation of Black Carbon Emissions from Dry Dipterocarp Forest Fires in Thailand

Directory of Open Access Journals (Sweden)

Ubonwan Chaiyo

2014-12-01

Full Text Available This study focused on the estimation of black carbon emissions from dry dipterocarp forest fires in Thailand. Field experiments were set up at the natural forest, Mae Nam Phachi wildlife sanctuary, Ratchaburi Province, Thailand. The dead leaves were the main component consumed of the surface biomass with coverage higher than 90% in volume and mass. The dead leaves load was 342 ± 190 g∙m−2 and followed by a little mass load of twig, 100 g∙m−2. The chemical analysis of the dead leaves showed that the carbon content in the experimental biomass fuel was 45.81 ± 0.04%. From the field experiments, it was found that 88.38 ± 2.02% of the carbon input was converted to carbon released to the atmosphere, while less than 10% were left in the form of residues, and returned to soil. The quantity of dead leaves consumed to produce each gram of carbon released was 2.40 ± 0.02 gdry biomass burned. From the study, the emissions factor of carbon dioxide, carbon monoxide, particulate matter (PM2.5 and black carbon amounted 1329, 90, 26.19 and 2.83 g∙kg−1dry biomass burned, respectively. In Thailand, the amount of black carbon emissions from dry dipterocarp forest fires amounted 17.43 tonnes∙y−1.

Global biomass burning - Atmospheric, climatic, and biospheric implicati ons [Introduction

International Nuclear Information System (INIS)

Zhu, Zhiliang; Teuber, K.B.

1991-01-01

On a global scale, the total biomass consumed by annual burning is about 8680 million tons of dry material; the estimated total biomass consumed by the burning of savanna grasslands, at 3690 million tons/year, exceeds all other biomass burning (BMB) components. These components encompass agricultural wastes burning, forest burning, and fuel wood burning. BMB is not restricted to the tropics, and is largely anthropogenic. Satellite measurements indicate significantly increased tropospheric concentrations of CO and ozone associated with BMB. BMB significantly enhances the microbial production and emission of NO(x) from soils, and of methane from wetlands

Air-water ‘tornado’-type microwave plasmas applied for sugarcane biomass treatment

Science.gov (United States)

Bundaleska, N.; Tatarova, E.; Dias, F. M.; Lino da Silva, M.; Ferreira, C. M.; Amorim, J.

2014-02-01

The production of cellulosic ethanol from sugarcane biomass is an attractive alternative to the use of fossil fuels. Pretreatment is needed to separate the cellulosic material, which is packed with hemicellulose and lignin in cell wall of sugarcane biomass. A microwave ‘tornado’-type air-water plasma source operating at 2.45 GHz and atmospheric pressure has been applied for this purpose. Samples of dry and wet biomass (˜2 g) have been exposed to the late afterglow plasma stream. The experiments demonstrate that the air-water highly reactive plasma environment provides a number of long-lived active species able to destroy the cellulosic wrapping. Scanning electron microscopy has been applied to analyse the morphological changes occurring due to plasma treatment. The effluent gas streams have been analysed by Fourier-transform infrared spectroscopy (FT-IR). Optical emission spectroscopy and FT-IR have been applied to determine the gas temperature in the discharge and late afterglow plasma zones, respectively. The optimal range of the operational parameters is discussed along with the main active species involved in the treatment process. Synergistic effects can result from the action of singlet O2(a 1Δg) oxygen, NO2, nitrous acid HNO2 and OH hydroxyl radical.

Air–water ‘tornado’-type microwave plasmas applied for sugarcane biomass treatment

International Nuclear Information System (INIS)

Bundaleska, N; Tatarova, E; Dias, F M; Lino da Silva, M; Ferreira, C M; Amorim, J

2014-01-01

The production of cellulosic ethanol from sugarcane biomass is an attractive alternative to the use of fossil fuels. Pretreatment is needed to separate the cellulosic material, which is packed with hemicellulose and lignin in cell wall of sugarcane biomass. A microwave ‘tornado’-type air–water plasma source operating at 2.45 GHz and atmospheric pressure has been applied for this purpose. Samples of dry and wet biomass (∼2 g) have been exposed to the late afterglow plasma stream. The experiments demonstrate that the air–water highly reactive plasma environment provides a number of long-lived active species able to destroy the cellulosic wrapping. Scanning electron microscopy has been applied to analyse the morphological changes occurring due to plasma treatment. The effluent gas streams have been analysed by Fourier-transform infrared spectroscopy (FT-IR). Optical emission spectroscopy and FT-IR have been applied to determine the gas temperature in the discharge and late afterglow plasma zones, respectively. The optimal range of the operational parameters is discussed along with the main active species involved in the treatment process. Synergistic effects can result from the action of singlet O 2 (a  1 Δ g ) oxygen, NO 2 , nitrous acid HNO 2 and OH hydroxyl radical. (paper)

The scale of biomass production in Japan

Energy Technology Data Exchange (ETDEWEB)

Matsumura, Yukihiko [School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashihiroshima-shi 739-8527 (Japan); Inoue, Takashi; Fukuda, Katsura [Global Warming Research Department, Mitsubishi Research Institute, Inc., 2-3-6 Ohtemachi, Chiyoda-ku, Tokyo 100-8141 (Japan); Komoto, Keiichi; Hada, Kenichiro [Renewable energy Team, Environment, Natural Resources and Energy Division, Mizuho Information and Research Institute, Inc., 2-3 Kanda-nishikicho, Chiyoda-ku, Tokyo 101-8443 (Japan); Hirata, Satoshi [Technical Institute, Kawasaki Heavy Industries, Ltd., 1-1 Kawasakicho, Akashi-shi, Hyogo 673-8666 (Japan); Minowa, Tomoaki [Biomass Recycle Research Laboratory, National Institute of Advanced and Industrial Science and Technology, 2-2-2 Hiro, Suehiro, Kure-shi, Hiroshima 737-0197 (Japan); Yamamoto, Hiromi [Socioeconomic Research Center, Central Research Institute of Electric Power Industry, 1-6-1 Ohtemachi, Chiyoda-ku, Tokyo 100-8126 (Japan)

2005-11-01

Policymakers working to introduce and promote the use of bioenergy in Japan require detailed information on the scales of the different types of biomass resources generated. In this research, the first of its type in Japan, the investigators reviewed various statistical resources to quantify the scale distribution of forest residues, waste wood from manufacturing, waste wood from construction, cattle manure, sewage sludge, night soil, household garbage, and waste food oil. As a result, the scale of biomass generation in Japan was found to be relatively small, on the average is no more than several tons in dry weight per day. (author)

Landsat Imagery-Based Above Ground Biomass Estimation and Change Investigation Related to Human Activities

Directory of Open Access Journals (Sweden)

Chaofan Wu

2016-02-01

Full Text Available Forest biomass is a significant indicator for substance accumulation and forest succession, and a spatiotemporal biomass map would provide valuable information for forest management and scientific planning. In this study, Landsat imagery and field data cooperated with a random forest regression approach were used to estimate spatiotemporal Above Ground Biomass (AGB in Fuyang County, Zhejiang Province of East China. As a result, the AGB retrieval showed an increasing trend for the past decade, from 74.24 ton/ha in 2004 to 99.63 ton/ha in 2013. Topography and forest management were investigated to find their relationships with the spatial distribution change of biomass. In general, the simulated AGB increases with higher elevation, especially in the range of 80–200 m, wherein AGB acquires the highest increase rate. Moreover, the forest policy of ecological forest has a positive effect on the AGB increase, particularly within the national level ecological forest. The result in this study demonstrates that human activities have a great impact on biomass distribution and change tendency. Furthermore, Landsat image-based biomass estimates would provide illuminating information for forest policy-making and sustainable development.

Spatial Distribution of Biomass and Woody Litter for Bio-Energy in Biscay (Spain

Directory of Open Access Journals (Sweden)

Esperanza Mateos

2018-05-01

Full Text Available Forest management has been considered a subject of interest, because they act as carbon (C sinks to mitigate CO 2 emissions and also as producers of woody litter (WL for bio-energy. Overall, a sustainably managed system of forests and forest products contributes to carbon mitigation in a positive, stable way. With increasing demand for sustainable production, the need to effectively utilise site-based resources increases. The utilization of WL for bio-energy can help meet the need for renewable energy production. The objective of the present study was to investigate biomass production (including C sequestration from the most representative forestry species (Pinus radiata D. Don and Ecualyptus globulus Labill of Biscay (Spain. Data from the third and fourth Spanish Forest Inventories (NFI3-2005 and NFI4-2011 were used. We also estimated the potential WL produced in the forest activities. Our findings were as follows: Forests of Biscay stored 12.084 Tg of biomass (dry basis, with a mean of 147.34 Mg ha - 1 in 2005 and 14.509 Tg of biomass (dry basis, with a mean of 179.82 Mg ha - 1 in 2011. The total equivalent CO 2 in Biscay’s forests increased by 1.629 Tg year - 1 between 2005 and 2011. The study shows that the energy potential of carbon accumulated in the WL amounted to 1283.2 million MJ year - 1 . These results suggest a considerable potential for energy production.

Characterization of the heterotrophic biomass and the endogenous residue of activated sludge.

Science.gov (United States)

Ramdani, Abdellah; Dold, Peter; Gadbois, Alain; Déléris, Stéphane; Houweling, Dwight; Comeau, Yves

2012-03-01

The activated sludge process generates an endogenous residue (X(E)) as a result of heterotrophic biomass decay (X(H)). A literature review yielded limited information on the differences between X(E) and X(H) in terms of chemical composition and content of extracellular polymeric substances (EPS). The objective of this project was to characterize the chemical composition (x, y, z, a, b and c in C(x)H(y)O(z)N(a)P(b)S(c)) of the endogenous and the active fractions and EPS of activated sludge from well designed experiments. To isolate X(H) and X(E) in this study, activated sludge was generated in a 200L pilot-scale aerobic membrane bioreactor (MBR) fed with a soluble and completely biodegradable synthetic influent of sodium acetate as the sole carbon source. This influent, which contained no influent unbiodegradable organic or inorganic particulate matter, allowed the generation of a sludge composed essentially of two fractions: heterotrophic biomass X(H) and an endogenous residue X(E), the nitrifying biomass being negligible. The endogenous decay rate and the active biomass fraction of the MBR sludge were determined in 21-day aerobic digestion batch tests by monitoring the VSS and OUR responses. Fractions of X(H) and X(E) were respectively 68% and 32% in run 1 (MBR at 5.2 day SRT) and 59% and 41% in run 2 (MBR at 10.4 day SRT). The endogenous residue was isolated by subjecting the MBR sludge to prolonged aerobic batch digestion for 3 weeks, and was characterized in terms of (a) elemental analysis for carbon, nitrogen, phosphorus and sulphur; and (b) content of EPS. The MBR sludge was characterized using the same procedures (a and b). Knowing the proportions of X(H) and X(E) in this sludge, it was possible to characterize X(H) by back calculation. Results from this investigation showed that the endogenous residue had a chemical composition different from that of the active biomass with a lower content of inorganic matter (1:4.2), of nitrogen (1:2.9), of phosphorus (1

Biomass energy in the making

International Nuclear Information System (INIS)

Anon.

2008-01-01

Wood, straw, agricultural residues, organic wastes, biomass is everywhere you look. But the efficient use of this source of green electricity - the world's second largest renewable energy source - requires optimization of biomass collection and combustion processes. Biomass is back on the political agenda. In mid-June of this year, the French government gave this renewable energy a boost by selecting twenty-two projects to generate power and heat with biomass. The plants, to be commissioned by 2010, will be located in eleven different regions and will consume energy from organic plant matter. The power generated will be bought at a firm price of 128 euros per megawatt-hour. Most of the fuel will come from forest and paper industry waste, but straw and even grape pomace will be used in some cases. The plants will have a combined generating capacity of 300 MWh, raising France's installed biomass capacity to a total of 700 MWe. A drop of water in the ocean in the overall scheme of France's electricity. It is true that France has long neglected biomass. In 2004, electricity generated from biological resources represented a mere 1.74 TWhe in France, just 0.3% of its power consumption. This will rise to 0.6% once the new plants have come on line. The trend is the same in all of the EU's 27 member states, according to Eurostat, the statistical office of the European Communities: the amount of electricity generated from biomass (including biogas, municipal waste and wood) has practically doubled in six years, rising from 40 to 80 TWhe between 2000 and 2005. This is an improvement, but it still only represents 2.5% of the electricity supplied to Europeans. On a global scale, biomass contributes just 1% of total electric power generation. Yet biomass is an energy resource found all over the world, whether as agricultural waste, wood chips, or dried treatment plant sludge, to name but a few. Biomass power plants have managed to gain a foothold mainly in countries that produce

Biomass production of sesbania sesban pers. On different habitats

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Pathak, P.S.; Roy, R.D.

1983-01-01

Three month-old seedlings of S. sesban (a shortlived medicinal shrub or small tree which can be used for fuelwood and forage) were planted at 7 sites starting in 1975. The seedlings were raised in polythene bags and planted in pits. Growth was assessed after 1.0-4.5 years by felling and measuring 3 sample trees each from 3 collar diameter (high, medium and low) groups at each site. Sites were (1) two nursery sites with optimum moisture and management conditions, assessed at 1 and 2.5 years old respectively, (2) three canal-side sites inundated for more than 8 months per year planted as blocks (assessed at 3.5 and 4.5 years) and as a single row (3.5 years), (3) a dry farm forestry site planted as a single row (assessed at 3.5 years) and (4) a moist silvopastoral site planted as a block (assessed at 3.5 years). Detailed growth and biomass data are tabulated. On the moist canal site plants were still growing at 4.5 year old (average above-ground biomass/plant 60 kg compared with 16-17 kg at 3.5 years); values were similar on the moist silvopastoral site (16 kg at 3.5 years) but lower on the dry site (6 kg at 3.5 years). On the nursery site average above-ground biomass increased from 2 kg/plant at 1 year old to 6 kg at 2.5 years. Collar diameter was linearly related to diameter at breast height and biomass, and diameter at breast height to biomass at all sites.

The effect of pulse voltage and capacitance on biosorption of uranium by biomass derived from whiskey distillery spent wash

Energy Technology Data Exchange (ETDEWEB)

Bustard, M.; Rollan, A.; McHale, A.P. [Biotechnology Research Group, School of Applied Biological and Chemical Sciences, University of Ulster (United Kingdom)

1999-01-01

Biosorption of uranium by residual biomass from The Old Bushmill`s Distillery Co. Ltd., Bushmills, Co. Antrim, Northern Ireland, following exposure to short and intense electric pulses has been examined. The biomass was prepared from the distillery spent wash and consisted of non-viable yeast and bacterial cells. As shown previously, untreated biomass had a maximum biosorption capacity of 170 mg uranium/g dry weight biomass. When biosorption reactions were placed between two electrodes and exposed to electric pulses with field strengths ranging from 1.25-3.25 kV/cm at a capacitance of 25 {mu}F, biosorption increased from 170 mg of uranium to 275 mg uranium/g dry weight biomass. The data were obtained from biosorption isotherm analyses and taken as the degree of biosorption at residual uranium concentrations of 3 mM. In addition, when the capacitance of the electric pulses increased from 0.25 {mu}F to 25 {mu}F at a fixed pulse field strength the degree of biosorption increased from 210 mg uranium to 240 mg uranium/g dry weight biomass. The results suggest that application of short and intense electric pulses to biosorption reactions may play an important role in enhancing microbial biosorption of toxic metals/radionuclides from waste water streams. (orig.) With 2 tabs., 10 refs.

Estimation of Viable Biomass In Wastewater And Activated Sludge By Determination of ATP, Oxygen Utilization Rate And FDA Hydrolysis

DEFF Research Database (Denmark)

Jørgensen, Poul-Erik; Eriksen, T.; Jensen, B.K.

1992-01-01

ATP content, oxygen utilization rate (OUR) and fluorescein diacetate (FDA) hydrolysis were tested for the ability to express the amount of viable biomass in wastewater and activated sludge. The relationship between biomass and these activity parameters was established in growth cultures made...... with biomass, while FDA hydrolysis in the sludge failed to show any such correlation. Conversion factors of 3 mg ATP/g dw, 300 mg O2/h g dw and 0.4 A/h (mg dw/ml) for ATP, OUR and FDA methods, respectively, were calculated. When the methods were applied for in situ determinations in four different wastewater...... plants, it was found that ATP content and respiration rate estimated viable biomass to range from 81 to 293 mg dw/g SS for raw wastewater and from 67 to 187 mg dw/g SS for activated sludge with a rather weak correlation between ATP and respiration measurements. The FDA hydrolysis estimated viable biomass...

ABOVE GROUND BIOMASS MICRONUTRIENTS IN A SEASONAL SUBTROPICAL FOREST

Directory of Open Access Journals (Sweden)

Hamilton Luiz Munari Vogel

2015-06-01

Full Text Available In the above ground biomass of a native forest or plantation are stored large quantities of nutrients, with few studies in the literature, especially concerning micronutrients. The present work aimed to quantify the micronutrients in above ground biomass in a Seasonal Subtropical forest in Itaara-RS, Brazil. For the above ground biomass evaluation, 20 trees of five different diameter classes were felled. The above ground biomass was separated in the following compartments: stem wood, stem bark, branches and leaves. The contents of B, Cu, Fe, Mn and Zn in the biomass samples were determined. The stock of micronutrients in the biomass for each component was obtained based on the estimated dry biomass, multiplied by the nutrient content. The total production of above ground biomass was estimated at 210.0 Mg.ha-1. The branches, stem wood, stem bark and leaves corresponded to 48.8, 43.3, 5.4 and 2.4% of the above ground biomass. The lower levels of B, Cu, Fe and Mn are in stem wood, except for Zn; in the branches and trunk wood are the largest stocks of B, Cu, Fe and Mn. In the branches, leaves and trunk bark are stored most micronutrients, pointing to the importance of these to remain on the soil.

Pyrolysis of forestry biomass by-products in Greece

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A. [Aristotle Univ. of Thessaloniki (Greece). Dept. of Chemical Engineering

1999-06-01

This article summarizes the technical characteristics of a biomass pyrolysis pilot plant recently constructed in central Greece. It highlights the considerations involved in achieving successful pyrolysis technology and environmental and developmental goals, by reviewing technical and nontechnical barriers associated with biomass treatment technology in Greece. Data from the start-up phase of the plant operation are presented and some aspects of the process are outlined. The capacity of the plant is 1200--1450 kg/hr, based on wet biomass (Arbutus Unedo) and the pyrolysis temperature is approximately 400 C. Char yield is 14--18% weight on dry basis and is of good quality consisting of 76% C with heat content 6760 kcal/kg. Bio-oil includes 64% C and its heat content is 6250 kcal/kg.

Characterization of drying parameters for solid fuels; Kiinteiden polttoaineiden kuivumis-parametrien karakterisointi

Energy Technology Data Exchange (ETDEWEB)

Impola, R; Saastamoinen, J [VTT Energy, Jyvaeskylae (Finland); Fagernaes, L [VTT Energy, Espoo (Finland)

1997-12-01

Drying of solid fuel particles in hot gases (50 - 200 deg C) is studied both theoretically and experimentally. The measurements are carried out by using a thermobalance reactor constructed for drying and pyrolysis studies of particles up to 30 mm by diameter. The model is based on the solution of the conservation equations for mass and energy. The main parameters affecting the drying rate are: particle size, particle shape, initial particle moisture content, gas temperature and gas moisture content, temperature of the reactor walls and slip velocity. Also, the drying of biomass fuel particles in fixed and moving beds with hot gas or steam is considered both experimentally and theoretically. A single particle drying model is coupled with a model describing heat and moisture transfer in the gas phase of the bed. The model can be used in the dimensioning of the drying system in a larger scale. Other study subjects were the movement of wood and peat particles in a pneumatic dryer, and the drying of a single fuel particle in steam under various pressures. The aim of the research work was to present a review of recent studies on emissions from biomass drying. The work covers the emissions from different feedstocks, and from different dryers and drying tests (atmospheric, pressurised, flue gas and steam drying), and the effects of factors, such as feedstock, dryer type and drying conditions, on the emissions. The formation and effects of the emissions, and methods to reduce them are also discussed

Biomass of active microorganisms is not limited only by available carbon in the rhizosphere

Science.gov (United States)

Gilmullina, Aliia

2017-04-01

Microbial activity is generally limited by carbon (C) availability. The easily available substrate release by roots creates so called "hotspots" in the rhizosphere that drives microbial activity removing C limitation. We simulated a gradient of root exudates by glucose addition at different concentrations to stimulate the activation of microbial biomass (MB). Glucose was added at the rates lower than MB (5, 10, 25 and 50%) and at the rates similar or higher than MB (100, 150, 200, 250, 300 and 400%). During incubation CO2 efflux was measured by conductometry, the size of active MB and specific growth rate were estimated by substrate-induced growth response method. We tested a hypothesis that glucose addition exceeding 100% MB is able to activate major fraction of soil microbial community. Addition of glucose at concentrations higher than 5% decreased specific growth rate, demonstrating the shift of microbial community from r-strategy to K-strategy. The percentage of active MB grew up by the increase of glucose concentration. The treatment with glucose at 100% presented a dramatic shift in the activation of MB up to 14%. Contrary to our hypothesis, further increase in glucose rate caused moderate stimulation of active MB up to 22% of total MB. Furthermore, glucose addition above 200% did not increase the fraction of active biomass indicating glucose oversaturation and possible limitation by other nutrients. The results suggest that despite the fact that C is the most important limitation factor, limitless C supply is not able to activate MB up to 100%. Thus, if the rhizosphere is limited by nutrients, the fraction of active biomass remains at low level despite an excess of available C.

Foliage biomass qualitative indices of selected forest forming tree species in Ukrainian Steppe

Directory of Open Access Journals (Sweden)

Sytnyk Svitlana

2017-06-01

Full Text Available Our study objective was research on the assimilation component of aboveground biomass of trees and its correlation with mensurational indices of trees (age, diameter and height in stands of the main forest forming species in the Ukrainian Northern Steppe zone - Pinus sylvestris L. (Scots pine and Robinia pseudoacacia L. (Black locust. The research was carried out in forest stands subordinated to the State Agency of Forest Resources of Ukraine. We used experimental data collected on sample plots established during years 2014-2016. The main research results prove that the foliage share in the tree greenery biomass structure had a wide range of values. For both investigated species, a positive correlation was found between the dry matter content in the tree foliage and the tree age, height and diameter. The foliage share in tree greenery biomass decreased with increasing mensurational index values. Correlation analysis revealed linear relationships between the mensurational indices and the discussed aboveground live biomass parameters. The closest correlation was observed between the stand age, mean stand diameter, mean stand height and dry matter content in the foliage.

Biomass a fast growing energy resource

International Nuclear Information System (INIS)

Hansen, Ulf

2003-01-01

Biomass as an energy resource is as versatile as the biodiversity suggests. The global net primary production, NPP, describes the annual growth of biomass on land and in the seas. This paper focuses on biomass grown on land. A recent estimate for the NPP on land is 120 billion tons of dry matter. How much of this biomass are available for energy purposes? The potential contribution of wood fuel and energy plants from sustainable production is limited to some 5% of NPP, i.e. 6 Bt. One third of the potential is energy forests and energy plantations which at present are not economic. One third is used in rural areas as traditional fuel. The remaining third would be available for modern biomass energy conversion. Biomass is assigned an expanding role as a new resource in the world's energy balance. The EU has set a target of doubling the share of renewable energy sources by 2010. For biomass the target is even more ambitious. The challenge for biomass utilization lies in improving the technology for traditional usage and expanding the role into other areas like power production and transportation fuel. Various technologies for biomass utilization are available among those are combustion, gasification, and liquefaction. Researchers have a grand vision in which the chemical elements in the hydrocarbon molecules of biomass are separated and reformed to yield new tailored fuels and form the basis for a new world economy. The vision of a new energy system based on fresh and fossilized biomass to be engineered into an environmentally friendly and sustainable fuel is a conceivable technical reality. One reason for replacing exhaustible fossil fuels with biomass is to reduce carbon emissions. The most efficient carbon dioxide emission reduction comes from replacing brown coal in a steam-electric unit, due to the efficiency of the thermal cycle and the high carbon intensity of the coal. The smallest emission reduction comes from substituting natural gas. (BA)

ORC power plant for electricity production from forest and agriculture biomass

International Nuclear Information System (INIS)

Borsukiewicz-Gozdur, A.; Wiśniewski, S.; Mocarski, S.; Bańkowski, M.

2014-01-01

Highlights: • Results for three variants of CHP plant fuelled by sawmill biomass are presented. • Octamethyltrisiloxane, MDM, methanol and H 2 O working fluids was conducted in CHP. • CHP with internal regeneration and “dry” working fluid has the highest electric power. • Power output, drying heat and drying temperature depend on CHP variant and ORC fluid. - Abstract: The paper presents the calculation results for three variants of CHP plant fuelled by sawmill biomass. The plant shall produce electricity and heat for a drying chamber. An analysis of the system efficiency for four different working fluids was conducted: octamethyltrisiloxane, methylcyclohexane, methanol and water. The highest electric power was obtained for the system with internal regeneration and methylcyclohexane applied as the “dry” working fluid, the highest temperature to supply the drying chamber was obtained for the system with external regeneration and octamethyltrisiloxane applied as the working fluid. The results of the analysis indicate that, by proper choice of the working fluid and of the regeneration variant (internal or external), it is possible to “adjust” the work of the system to the needs and expectations of the plant investor (user)

MODEL BASED BIOMASS SYSTEM DESIGN OF FEEDSTOCK SUPPLY SYSTEMS FOR BIOENERGY PRODUCTION

Energy Technology Data Exchange (ETDEWEB)

David J. Muth, Jr.; Jacob J. Jacobson; Kenneth M. Bryden

2013-08-01

Engineering feedstock supply systems that deliver affordable, high-quality biomass remains a challenge for the emerging bioenergy industry. Cellulosic biomass is geographically distributed and has diverse physical and chemical properties. Because of this feedstock supply systems that deliver cellulosic biomass resources to biorefineries require integration of a broad set of engineered unit operations. These unit operations include harvest and collection, storage, preprocessing, and transportation processes. Design decisions for each feedstock supply system unit operation impact the engineering design and performance of the other system elements. These interdependencies are further complicated by spatial and temporal variances such as climate conditions and biomass characteristics. This paper develops an integrated model that couples a SQL-based data management engine and systems dynamics models to design and evaluate biomass feedstock supply systems. The integrated model, called the Biomass Logistics Model (BLM), includes a suite of databases that provide 1) engineering performance data for hundreds of equipment systems, 2) spatially explicit labor cost datasets, and 3) local tax and regulation data. The BLM analytic engine is built in the systems dynamics software package PowersimTM. The BLM is designed to work with thermochemical and biochemical based biofuel conversion platforms and accommodates a range of cellulosic biomass types (i.e., herbaceous residues, short- rotation woody and herbaceous energy crops, woody residues, algae, etc.). The BLM simulates the flow of biomass through the entire supply chain, tracking changes in feedstock characteristics (i.e., moisture content, dry matter, ash content, and dry bulk density) as influenced by the various operations in the supply chain. By accounting for all of the equipment that comes into contact with biomass from the point of harvest to the throat of the conversion facility and the change in characteristics, the

Development of a catalytic system for gasification of wet biomass

Energy Technology Data Exchange (ETDEWEB)

Elliott, D.C.; Sealock, L.J.; Phelps, M.R.; Neuenschwander, G.G.; Hart, T.R. [Pacific Northwest Lab., Richland, WA (United States)

1993-12-31

A gasification system is under development at Pacific Northwest Laboratory that can be used with high-moisture biomass feedstocks. The system operates at 350{degrees}C and 205 atm using a liquid water phase as the processing medium. Since a pressurized system is used, the wet biomass can be fed as a slurry to the reactor without drying. Through the development of catalysts, a useful processing system has been produced. This paper includes assessment of processing test results of different catalysts. Reactor system results including batch, bench-scale continuous, and engineering-scale processing results are presented to demonstrate the applicability of this catalytic gasification system to biomass. The system has utility both for direct conversion of biomass to fuel gas or as a wastewater cleanup system for treatment of unconverted biomass from bioconversion processes. By the use of this system high conversions of biomass to fuel gas can be achieved. Medium-Btu is the primary product. Potential exists for recovery/recycle of some of the unreacted inorganic components from the biomass in the aqueous byproduct stream.

Changes of hydrogen peroxide and radical-scavenging activity of raspberry during osmotic, convective, and freeze-drying.

Science.gov (United States)

Novaković, Miroslav M; Stevanović, Snežana M; Gorjanović, Stanislava Ž; Jovanovic, Predrag M; Tešević, Vele V; Janković, Miodrag A; Sužnjević, Desanka Ž

2011-05-01

This study was conducted to investigate the influence of different drying treatments on antioxidant (AO) activity and phenolic content of raspberry (Rubus idaeus), cultivar Willamette. Whole raspberry fruits were dried convectively (air-drying), osmotically, and freeze-dried. Acetone-water extracts of fresh and dried raspberries were assessed for total phenolic content by standard Folin-Ciocalteau method. Two AO assays were applied, a recently developed direct current (DC) polarographic assay based on decrease of anodic oxidation current of hydrogen peroxide and widely used radical scavenge against the 1,1-diphenyl-2-picrylhydrazyl (DPPH). Strong correlation has been obtained between both AO assays and total phenolic content. In addition, some individual phenolic compounds present in raspberry have been assessed using DPPH and DC polarographic assay. Comparison and evaluation of drying methods has been based on preservation of AO activity and total phenolic content. Obtained results confirmed superiority of freeze-drying; convective drying caused slight changes while osmotic dehydration showed a significant decrease of phenolic compounds and AO activity. © 2011 Institute of Food Technologists®

Technical and economic analysis of using biomass energy

Directory of Open Access Journals (Sweden)

Piaskowska-Silarska Małgorzata

2017-01-01

Full Text Available In the first part of the article were presented the technical possibilities of obtaining solid biomass, biogas, landfill gas, a biogas from wastewater treatment plants, bioethanol and biodiesel. Then processes was described, allowing use of energy from biomass. As first was discussed the incineration which includes drying and degassing of the wood materials, wood gas burning at 1200°C, post-combustion gas and heat transfer in the heat exchanger. Then had been described gasification, or thermochemical conversion process, occurring at high temperature. It is two-stage process. In the first chamber at deficiency of air and at relatively low temperatures (450–800°C, the fuel is being degasified, resulting in creating combustible gas and a mineral residue (charcoal. In the second stage, secondary combustion chamber and at a temperature of about 1000–1200°C and in the presence of excess of oxygen resultant gas is burned. A further process is pyrolysis. It consists of the steps of drying fuel to a moisture level below 10%, milling the biomass into very small particles, the pyrolysis reaction, separation of solid products, cooling and collecting bio-oil. Then discusses co-generation, which is combined production of heat and electricity. In this situation where the biomass contains too much water it can be used for energy purposes through biochemical processes. The alcoholic fermentation results in decomposition of carbohydrates taking place under anaerobic conditions, and the product is bioethanol. Another biochemical process used for the production of liquid biofuels is esterification of vegetable oils. Methane fermentation in turn causes a decomposition of macromolecular organic substances with limited oxygen available. As a result, we obtain alcohols, lower organic acids, methane, carbon dioxide and water. There was analysis of economic increasing of solid biomass energy, biogas and liquid biofuels in the following article.

Investigation of antineoplastic activity of chewing tablets based on dry oat extract and quercetin

Directory of Open Access Journals (Sweden)

Ярослав Ростиславович Андрійчук

2015-07-01

Full Text Available One of the main goals of domestic pharmaceutical science is development of new medicines. Thus, new tablet drug was created based on dry oat extract and quercetin. Investigation of antineoplastic activity was performed. Antineoplastic activity of investigational drug based on dry oat extract and quercetin was experimentally proved.

Cultivation of Azolla microphylla biomass on secondary-treated Delhi municipal effluents

Energy Technology Data Exchange (ETDEWEB)

Arora, A.; Saxena, S. [Indian Agricultural Research Institute, New Delhi (India). Centre for Conservation of Blue Green Algae

2005-07-01

Study was conducted on recycling municipal wastewaters for cultivation of Azolla microphylla biomass, which is used for inoculation into paddy fields as N biofertiliser and has other applications as green manure, animal feed and biofilter. Secondary-treated municipal wastewaters were collected from Wazirabad sewage treatment plant in New Delhi during all four seasons and tested for reactive P and heavy metal content. The reactive P levels in effluents ranged between 1-2 ppm and levels of heavy metals like Cd, Pb, Ni, Zn, Fe and Mn were well below permissible limits. A. microphylla was grown in sewage effluents and its dilutions prepared with tapwater. It showed good growth potential on sewage effluents. Doubling times during September and December months compared well with those on Espinase and Watanabe (E and W) medium and tapwater. Dried Azolla biomass produced on sewage waters did not show presence of toxic heavy metals Cd, Cr and Pb. However, levels of P in dried biomass cultivated on sewage effluents were lower as compared to those from E and W medium and tapwater. The biomass produced can be used for inoculating paddy fields or for other applications and polished wastewaters can be recycled for irrigation purposes. (author)

Improvement of biomass production and glucoamylase activity by Candida famata using factorial design.

Science.gov (United States)

Mosbah, Habib; Aissa, Imen; Hassad, Nahla; Farh, Dhaker; Bakhrouf, Amina; Achour, Sami

2016-07-01

To improve biomass production and glucoamylase activity (GA) by Candida famata, culture conditions were optimized. A 2(3) full factorial design (FFD) with a response surface model was used to evaluate the effects and interactions of pH (X1 ), time of cultivation (X2 ), and starch concentration (X3 ) on the biomass production and enzyme activity. A total of 16 experiments were conducted toward the construction of an empiric model and a first-order equation. It was found that all factors (X1 , X2 , and X3 ) and their interactions were significant at a certain confidence level (P production and GA of C. famata. Under this optimized medium, the experimental biomass production and GA obtained were 1.8 ± 0.54 g/L and 0.078 ± 0.012 µmol/L/Min, about 1.5- and 1.8-fold, respectively, higher than those in basal medium. The (R(2) ) coefficients obtained were 0.997 and 0.990, indicating an adequate degree of reliability in the model. Approximately 99% of validity of the predicted value was achieved. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

A theoretical and experimental study of the thermal degradation of biomass

Energy Technology Data Exchange (ETDEWEB)

Groenli, Morten G.

1996-12-31

This thesis relates to the thermal degradation of biomass covering a theoretical and experimental study in two parts. In the first part, there is presented an experimental and modeling work on the pyrolysis of biomass under regimes controlled by chemical kinetics, and the second part presents an experimental and modeling work on the pyrolysis of biomass under regimes controlled by heat and mass transfer. Five different celluloses, and hemicellulose and lignin isolated from birch and spruce have been studied by thermogravimetry. The thermo grams of wood species revealed different weight loss characteristics which can be attributed to their different chemical composition. The kinetic analysis gave activation energies between 210 and 280 kJ/mole for all the celluloses, and a model of independent parallel reactions was successfully used to describe the thermal degradation. In the second part of the thesis there is presented experimental and modeling work on the pyrolysis of biomass under regimes controlled by heat and mass transfer. The effect of heating conditions on the product yields distribution and reacted fraction was investigated. The experiments show that heat flux alters the pyrolysis products as well as the intra particle temperatures to the greatest extent. A comprehensive mathematical model which can simulate drying and pyrolysis of moist wood is presented. The simulation of thermal degradation and heat transport processes agreed well with experimental results. 198 refs., 139 figs., 68 abs.

Technoeconomic assessment of biomass to energy

International Nuclear Information System (INIS)

Mitchell, C.P.; Watters, M.P.

1995-01-01

A spreadsheet-based decision support system has been developed that allows easy evaluation of integrated biomass to electricity and biomass to ethanol systems. The Bioenergy Assessment Model (BEAM) has been developed to allow the techno-economic assessment of biomass to electricity and biomass to ethanol schemes, including investigation of the interfacing issues. Technical and economic parameters can be assessed for a variety of feedstocks, conversion technologies and generating cycles. Production modules are currently available for biomass supply from short rotation coppice and conventional forestry relevant to conditions and practices in NW Europe. The biomass conversion modules include pre-treatment (reception, storage, handling, comminution, screening and drying); atmospheric gasification (generic gasifier, wet gas scrubbing, dual fuel engine); pressure gasification (generic gasifier, hot gas filtration, gas turbine combined cycle); fast pyrolysis for liquid bio-fuel-oil (pyrolyser, oil storage, pilot-injected diesel engine); combustion (fluid bed combuster steam turbine), conventional acid hydrolysis fermentation and the NREL SSF process to ethanol. In addition there is a further module which can be used to examine the collection, mass burn and generation of electricity from MSW. BEAM has been used, and the results presented in this paper, to determine the costs of generating bio-electricity from short rotation coppice and conventional forestry over a range of power outputs and for each conversion technology. Alternative feedstock supply strategies have been examined and relations drawn between delivered feedstock cost and cost of electricity. (author)

A lifetime perspective of biomass allocation in Quercus pubescens trees in a dry, alpine valley

NARCIS (Netherlands)

Slot, M.; Janse-ten Klooster, S.H.; Sterck, F.J.; Sass-Klaassen, U.; Zweifel, R.

2012-01-01

Plasticity of biomass allocation is a key to growth and survival of trees exposed to variable levels of stress in their lifetime. Most of our understanding of dynamic biomass allocation comes from seedling studies, but plasticity may be different in mature trees. We used stem analysis to reconstruct

The opportunities for obtaining of the biogas on methane fermentation from marine algae biomass and water plant biomass

Directory of Open Access Journals (Sweden)

Jachniak Ewa

2018-01-01

Full Text Available The aim of the research was to try to obtain of the biogas on a laboratory scale from marine algae biomass and water plant biomass. The research was conducted in 2016 year and samples were taken from the Polish coast of the Baltic Sea. In laboratory work, algae and plant species were first identified. The next, in order to subject them to methane fermentation processes and to obtain biogas,partial mechanical treatment of the biomass was conducted. Dry matter content and dry organic matter content were also determined. The research has shown different production of the biogas depending on the various species of the algae and plants. The percentage composition of the biogas was also determined (% CO2 and % CH4. In this research some kinds and species of algae and aquatic plants were distinguished: Scytosiphon cf. S. tortilis, Fucus vesiculosus, Cladophora, Audouinella, Potamogeton perfoliatus. Production of biogas from selected algae and water plants oscillated between 0.023 dm3·g-1 and 0.303 dm3·g-1. The highest content of the methane in biogas was obtained from the mixture of Ectocarpus from spring and autumn harvest (values oscillated from 80.7 % to 81.2 %, while the highest percentage share of carbon dioxide in the biogas was characterized by the mixture Fucus vesiculosus and Audouinella (22 %. Due to a small amount of the research in this field, more research is needed.

Assessing the regional impact of indonesian biomass burning emissions based on organic molecular tracers and chemical mass balance modeling

Science.gov (United States)

Engling, G.; He, J.; Betha, R.; Balasubramanian, R.

2014-08-01

Biomass burning activities commonly occur in Southeast Asia (SEA), and are particularly intense in Indonesia during the dry seasons. The effect of biomass smoke emissions on air quality in the city state of Singapore was investigated during a haze episode in October 2006. Substantially increased levels of airborne particulate matter (PM) and associated chemical species were observed during the haze period. Specifically, the enhancement in the concentration of molecular tracers for biomass combustion such as levoglucosan by as much as two orders of magnitude and the diagnostic ratios of individual organic compounds indicated that biomass burning emissions caused a regional smoke haze episode due to their long-range transport by prevailing winds. With the aid of air mass backward trajectories and chemical mass balance modeling, large-scale forest and peat fires in Sumatra and Kalimantan were identified as the sources of the smoke aerosol, exerting a significant impact on air quality in downwind areas, such as Singapore.

Spontaneous and UV-induced variations in the activity of biomass synthesis in Candida utilis haploid and diploid strains

International Nuclear Information System (INIS)

Kondrat'eva, T.F.; Lin'kova, M.A.; Lobacheva, N.A.

1988-01-01

Candida utilis diploid strains have greater variations induced by UV irradiation in the activity of biomass synthesis as compared with the parent haploid culture. Clones with an activity of the synthesis greater that the mean population one appear more frequently in the diploid strains. Mathematical analysis has confirmed the significance of the results and the hypothesis according to which the frequency of variants more active in biomass synthesis rises after the action of UV

Responses of benthic bacteria to experimental drying in sediments from Mediterranean temporary rivers.

Science.gov (United States)

Amalfitano, Stefano; Fazi, Stefano; Zoppini, Annamaria; Barra Caracciolo, Anna; Grenni, Paola; Puddu, Alberto

2008-02-01

In the semiarid Mediterranean regions, water scarcity represents a common physiological stress for microbial communities residing in river sediments. However, the effect of drying has not yet adequately been evaluated when analyzing riverine microbiological processes. The bacterial community structure (abundance, biomass, composition) and functioning (carbon production, live cell percentage) were assessed during experimental desiccation in microcosms with sediments from different Mediterranean temporary rivers (Tagliamento, Krathis, Mulargia, Pardiela). Our results showed that the overall responses to drying of the bacterial community were independent from sediment origin and strictly related to water content. During desiccation, a prompt decline (up to 100%) of the initial bacterial carbon production was followed by a slower decrease in abundance and biomass, with an overall reduction of 74% and 78%, respectively. By the end of the experiment, live cells were still abundant but depressed in their main metabolic functions, thus resulting in a drastic increase in the community turnover time. Only 14% of the initial live cell biomass was available in dry sediments to immediately start the reactivation of the aquatic microbial food web after the arrival of new water. Community composition analysis showed a relative increase in alpha- and beta-Proteobacteria, when passing from wet to dry conditions. Our results suggest that the occurrence of drought events could affect carbon cycling through the freshwater microbial compartment, by temporarily limiting microbial mineralization and altering bacterial community structure.

Pyrolysis of forestry biomass by-products in Greece

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A.

1999-06-01

This article summarizes the technical characteristics of a biomass pyrolysis pilot plant recently constructed in central Greece. It highlights the considerations involved in achieving successful pyrolysis technology and environmental and developmental goals, by reviewing technical and nontechnical barriers associated with biomass treatment technology in Greece. Data from the start-up phase of the plant operation are presented and some aspects of the process are outlined. The capacity of the plant is 1200 1450 kg hr, based on wet biomass (Arbutus Unedo) and the pyrolysis temperature is approximately 400{sup o}C. Char yield is 1418 % weight on dry basis and is of good quality consisting of 76{sup o}C with heat content 6760 kcal kg. Bio-oil includes 63% C and its heat content is 6250 kcal kg. (author)

Effect of biomass open burning on particulate matter and polycyclic aromatic hydrocarbon concentration levels and PAH dry deposition in ambient air.

Science.gov (United States)

Chiu, Jui C; Shen, Yun H; Li, Hsing W; Chang, Shun S; Wang, Lin C; Chang-Chien, Guo P

2011-01-01

The objectives of the present study were to investigate particulate matter (PM) and polycyclic aromatic hydrocarbon (PAH) concentrations in ambient air during rice straw open burning and non-open burning periods. In the ambient air of a rice field, the mean PM concentration during and after an open burning event were 1828 and 102 μg m⁻³, respectively, which demonstrates that during a rice field open burning event, the PM concentration in the ambient air of rice field is over 17 times higher than that of the non-open burning period. During an open burning event, the mean total PAH and total toxic equivalence (BaP(eq)) concentrations in the ambient air of a rice field were 7206 ng m⁻³ and 10.3 ng m⁻³, respectively, whereas after the open burning event, they were 376 ng m⁻³ and 1.50 ng m⁻³, respectively. Open burning thus increases total PAH and total BaP(eq) concentrations by 19-fold and 6.8-fold, respectively. During a rice straw open burning event, in the ambient air of a rice field, the mean dry deposition fluxes of total PAHs and total BaP(eq) were 1222 μg m⁻² day⁻¹ and 4.80 μg m⁻² day⁻¹, respectively, which are approximately 60- and 3-fold higher than those during the non-open burning period, respectively. During the non-open burning period, particle-bound PAHs contributed 79.2-84.2% of total dry deposition fluxes (gas + particle) of total PAHs. However, an open burning event increases the contribution to total PAH dry deposition by particle-bound PAHs by up to 85.9-95.5%. The results show that due to the increased amount of PM in the ambient air resulting from rice straw open burning, particle-bound PAHs contributed more to dry deposition fluxes of total PAHs than they do during non-open burning periods. The results show that biomass (rice straw) open burning is an important PAH emission source that significantly increases both PM and PAH concentration levels and PAH dry deposition in ambient air.

Ensiling as biological pretreatment of grass (Festulolium Hykor): The effect of composition, dry matter, and inocula on cellulose convertibility

DEFF Research Database (Denmark)

Ambye-Jensen, Morten; Johansen, Katja Salomon; Didion, Thomas

2013-01-01

Grass biomass is a prospective type of lignocellulosic biomass for bioenergy and fuel production, but the low dry matter in grass at harvest calls for new pretreatment strategies for cellulosic conversion. In this study, ensiling was tested as a biological pretreatment method of the high yielding...... grass variety Festulolium Hykor. The biomass was harvested in four cuts over a growing season. Three important factors of ensiling: biomass composition, dry matter (DM) at ensiling, and inoculation of lactic acid bacteria, were assessed in relation to subsequent enzymatic cellulose hydrolysis....... The organic acid profile after ensiling was dependant on the composition of the grass and the DM, rather than on the inocula. High levels of organic acids, notably lactic acid, produced during ensiling improved enzymatic cellulose convertibility in the grass biomass. Ensiling of less mature grass gave higher...

Production of Saccharomyces cerevisiae biomass in papaya extract ...

African Journals Online (AJOL)

Extracts of papaya fruit were used as substrate for single cell protein (SCP) production using Saccharomyces cerevisiae. A 500 g of papaya fruit was extracted with different volumes of sterile distilled water. Extraction with 200 mL of sterile distilled water sustained highest cell growth. Biochemical analysis of dry biomass ...

Microalgal biomass and lipid production in mixed municipal, dairy, pulp and paper wastewater together with added flue gases.

Science.gov (United States)

Gentili, Francesco G

2014-10-01

The aim of the study was to grow microalgae on mixed municipal and industrial wastewater to simultaneously treat the wastewater and produce biomass and lipids. All algal strains grew in all wastewater mixtures; however, Selenastrum minutum had the highest biomass and lipids yields, up to 37% of the dry matter. Nitrogen and phosphorus removal were high and followed a similar trend in all three strains. Ammonium was reduced from 96% to 99%; this reduction was due to algal growth and not to stripping to the atmosphere, as confirmed by the amount of nitrogen in the dry algal biomass. Phosphate was reduced from 91% to 99%. In all strains used the lipid content was negatively correlated to the nitrogen concentration in the algal biomass. Mixtures of pulp and paper wastewater with municipal and dairy wastewater have great potential to grow algae for biomass and lipid production together with effective wastewater treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fiscal 1998 achievement report on regional consortium research and development project. Regional consortium of venture business fostering type--Creation of key industries (Development of technologies for manufacturing and utilizing various biological regulatory substances using Hokkaido-produced biomasses as materials); 1998 nendo Dosan biomass wo genryo to shita kakushu seitai chosetsu kino busshitsu no seisan riyo gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The efforts aim to meet consumers' needs for products that will prevent lifestyle diseases or the like. For this purpose, substances answering the purpose are extracted from Hokkaido-produced agricultural and aquatic biomasses, and prepared for testing. Researches are conducted on how they behave in the enzyme, cell, and biological systems, and active substances are isolated and identified. In relation to the aquatic biomass, a technology is established of extracting and separating DHA (docosahexaenoic acid), EPA (eicosapentaenoic acid), taurine, etc., which are multivalent unsaturated fatty acids effective in preventing lifestyle diseases, from the unused parts of the squid. In relation to the agricultural biomass, antimicrobial active substances are extracted and separated from small fruit plants such as the chicory. Long-keeping foods are tentatively produced by the addition of dried powder of the chicory root tuber. In the elucidation of various biological regulatory substances contained in the Hokkaido-produced biomasses, they are tested for their abilities to resist microbes and active oxygen. Furthermore, verification tests are conducted by administering the substances to the senescence-accelerated mouse (SAM). (NEDO)

Influence of landscape structure and human modifications on insect biomass and bat foraging activity in an urban landscape.

Science.gov (United States)

Threlfall, Caragh G; Law, Bradley; Banks, Peter B

2012-01-01

Urban landscapes are often located in biologically diverse, productive regions. As such, urbanization may have dramatic consequences for this diversity, largely due to changes in the structure and function of urban communities. We examined the influence of landscape productivity (indexed by geology), housing density and vegetation clearing on the spatial distribution of nocturnal insect biomass and the foraging activity of insectivorous bats in the urban landscape of Sydney, Australia. Nocturnal insect biomass (g) and bat foraging activity were sampled from 113 sites representing backyard, open space, bushland and riparian landscape elements, across urban, suburban and vegetated landscapes within 60 km of Sydney's Central Business District. We found that insect biomass was at least an order of magnitude greater within suburban landscapes in bushland and backyard elements located on the most fertile shale influenced geologies (both plandscapes. Similarly, the feeding activity of bats was greatest in bushland, and riparian elements within suburbs on fertile geologies (p = 0.039). Regression tree analysis indicated that the same three variables explained the major proportion of the variation in insect biomass and bat foraging activity. These were ambient temperature (positive), housing density (negative) and the percent of fertile shale geologies (positive) in the landscape; however variation in insect biomass did not directly explain bat foraging activity. We suggest that prey may be unavailable to bats in highly urbanized areas if these areas are avoided by many species, suggesting that reduced feeding activity may reflect under-use of urban habitats by bats. Restoration activities to improve ecological function and maintain the activity of a diversity of bat species should focus on maintaining and restoring bushland and riparian habitat, particularly in areas with fertile geology as these were key bat foraging habitats.

Influence of landscape structure and human modifications on insect biomass and bat foraging activity in an urban landscape.

Directory of Open Access Journals (Sweden)

Caragh G Threlfall

Full Text Available Urban landscapes are often located in biologically diverse, productive regions. As such, urbanization may have dramatic consequences for this diversity, largely due to changes in the structure and function of urban communities. We examined the influence of landscape productivity (indexed by geology, housing density and vegetation clearing on the spatial distribution of nocturnal insect biomass and the foraging activity of insectivorous bats in the urban landscape of Sydney, Australia. Nocturnal insect biomass (g and bat foraging activity were sampled from 113 sites representing backyard, open space, bushland and riparian landscape elements, across urban, suburban and vegetated landscapes within 60 km of Sydney's Central Business District. We found that insect biomass was at least an order of magnitude greater within suburban landscapes in bushland and backyard elements located on the most fertile shale influenced geologies (both p<0.001 compared to nutrient poor sandstone landscapes. Similarly, the feeding activity of bats was greatest in bushland, and riparian elements within suburbs on fertile geologies (p = 0.039. Regression tree analysis indicated that the same three variables explained the major proportion of the variation in insect biomass and bat foraging activity. These were ambient temperature (positive, housing density (negative and the percent of fertile shale geologies (positive in the landscape; however variation in insect biomass did not directly explain bat foraging activity. We suggest that prey may be unavailable to bats in highly urbanized areas if these areas are avoided by many species, suggesting that reduced feeding activity may reflect under-use of urban habitats by bats. Restoration activities to improve ecological function and maintain the activity of a diversity of bat species should focus on maintaining and restoring bushland and riparian habitat, particularly in areas with fertile geology as these were key bat

The use of corn (ZEA MAYS) biomass in drying process

International Nuclear Information System (INIS)

Kricka, T.; Pliestic, S.

1996-01-01

The most important agricultural crop in the world, besides wheat and rice is corn. In the last 10 years, Republic of Croatia has produced about 2000000 tons of corn. Most of that is used for food and feed and for seed production and it is 1000000 tons in quantity. This quantity demands between 35000 to 40000 tons of oil. For the reason, this paper describes the possibilities of the substitution of oil with corn biomass after harvesting. (author)

Biomass consumption and CO2, CO and main hydrocarbon gas emissions in an Amazonian forest clearing fire

Science.gov (United States)

T. G. Soares Neto; J. A. Carvalho; C. A. G. Veras; E. C. Alvarado; R. Gielow; E. N. Lincoln; T. J. Christian; R. J. Yokelson; J. C. Santos

2009-01-01

Biomass consumption and CO2, CO and hydrocarbon gas emissions in an Amazonian forest clearing fire are presented and discussed. The experiment was conducted in the arc of deforestation, near the city of Alta Floresta, state of Mato Grosso, Brazil. The average carbon content of dry biomass was 48% and the estimated average moisture content of fresh biomass was 42% on...

Biomass - Activities and projects in 2004; Biomasse - Aktivitaeten und Projekte 2004

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D; Guggisberg, B

2005-07-01

This annual report by the Swiss Federal Office of Energy (SFOE) presents an overview of the Swiss research programme on biomass and its efficient use both as a source of heat and electrical power and as a fuel. Work done and results obtained in the year 2004 are looked at. Topics covered include combustion and gasification of wood, the fermentation of biogenic wastes and developments in the bio-fuels area. Several projects in each of these areas are discussed. National co-operation with various universities, private organisations and other federal offices is discussed, as are contributions made to symposia and exhibitions in the biomass area. International co-operation within the framework of International Energy Agency (IEA) tasks is mentioned. Various pilot and demonstration projects in the combustion, gasification and fermentation areas are listed and discussed.

EERC Center for Biomass Utilization 2006

Energy Technology Data Exchange (ETDEWEB)

Zygarlicke, Christopher J. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Hurley, John P. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Aulich, Ted R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Folkedahl, Bruce C. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Strege, Joshua R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Patel, Nikhil [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Shockey, Richard E. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center

2009-05-27

The Center for Biomass Utilization® 2006 project at the Energy & Environmental Research Center (EERC) consisted of three tasks related to applied fundamental research focused on converting biomass feedstocks to energy, liquid transportation fuels, and chemicals. Task 1, entitled Thermochemical Conversion of Biomass to Syngas and Chemical Feedstocks, involved three activities. Task 2, entitled Crop Oil Biorefinery Process Development, involved four activities. Task 3, entitled Management, Education, and Outreach, focused on overall project management and providing educational outreach related to biomass technologies through workshops and conferences.

Asymptotic Approximations to the Non-Isothermal Distributed Activation Energy Model for Bio-Mass Pyrolysis

Directory of Open Access Journals (Sweden)

Dhaundiyal Alok

2017-12-01

Full Text Available This paper describes the influence of some parameters significant to biomass pyrolysis on the numerical solutions of the non-isothermal nth order distributed activation energy model (DAEM using the Gamma distribution and discusses the special case for the positive integer value of the scale parameter (λ, i.e. the Erlang distribution. Investigated parameters are the integral upper limit, the frequency factor, the heating rate, the reaction order, and the shape and rate parameters of the Gamma distribution. Influence of these parameters has been considered for the determination of the kinetic parameters of the non-isothermal nth order Gamma distribution from the experimentally derived thermoanalytical data of biomass pyrolysis. Mathematically, the effect of parameters on numerical solution is also used for predicting the behaviour of the unpyrolysized fraction of biomass with respect to temperature. Analysis of the mathematical model is based upon asymptotic expansions, which leads to the systematic methods for efficient way to determine the accurate approximations. The proposed method, therefore, provides a rapid and highly effective way for estimating the kinetic parameters and the distribution of activation energies.

The availability of biomass for energy production

International Nuclear Information System (INIS)

Zeevalkink, J.A.; Borsboom, N.W.J.; Sikkema, R.

1997-12-01

The Dutch energy policy aims at 75 PJ energy production from biomass in the Netherlands by the year 2020. This requires the development of a biomass market for biomass fuels so that suppliers as well as users can sell and buy biomass, respectively. The study concentrates on the contribution that information about biomass supply and demand can make to the realization of such a market for biomass fuels and stimulating its functioning. During the study, an inventory was made of public information on biomass quantities that are expected to become available for energy production in the short term. It was proposed to set up a database that contains information about the supply and suppliers of forest wood (specifically thinnings), (clean) waste wood from wood-processing industries, used timber and green wood waste from public parks. On the basis of rough estimates it can be concluded that these biomass flows account for an approximate annual quantity of 900,000 tonnes of dry biomass, or an annual 16,000 W energy production. This quantity would cover 66% of the goal set for the year 2000 and 20% of the goal set for 2020. Various database models were described and discussed during a workshop which was organized for potentially interested parties so as to find out their interest in and potential support for such an information system. Though the results of the survey conducted earlier suggested otherwise, it turned out that there was only minor interest in an information system, i.e. there was an interest in a survey of the companies involved in biomass supply and demand. In addition, most parties preferred bilateral confidential contacts to contract biomass. The opinion of many parties was that Novem's major tasks were to characterize biomass quality, and to give support to the discussions about the legal framework for using (waste) wood for energy production. It was concluded that at this moment a database must not be set up; in the future, however, there could be a

Seasonal variations in biomass and species composition of seaweeds along the northern coasts of Persian Gulf (Bushehr Province)

Science.gov (United States)

Dadolahi-Sohrab, A.; Garavand-Karimi, M.; Riahi, H.; Pashazanoosi, H.

2012-02-01

This study was carried out to evaluate the seasonal variations of seaweed biomass and species composition at six different sites along the coastal areas in Bushehr Province. Sampling depths varied among sites, from 0.3 to 2.0 m below mean sea level. A total of 37 (i.e., 10 Chlorophyta, 12 Phaeophyta and 15 Rhodophyta) seaweed species were collected. Studies were conducted for quantifying the seaweeds during four seasons from October 2008 until July 2009. During present research, Ulva intestinalis and Cladophora nitellopsis of green, Polycladia myrica, Sirophysalia trinodis and Sargassum angustifolium of brown and Gracilaria canaliculata and Hypnea cervicornis of red seaweeds showed highest biomass in coastal areas of Bushehr Province. The Cheney`s ratio of 2.1 indicated a temperate algal flora to this area. All sites exhibited more than 50% similarity of algal species, indicating a relatively homogenous algal distribution. Total biomass showed the highest value of 3280.7 ± 537.8 g dry wt m - 2 during summer and lowest value of 856.9 ± 92.0 g dry wt m - 2 during winter. During this study, the highest and lowest seaweed biomass were recorded on the site 2 (2473.7 ± 311.0 g dry wt m - 2) and site 5 (856.7 ± 96.8 g dry wt m - 2), respectively.

Large-scale carbon stock assessment of woody vegetation in tropical dry deciduous forest of Sathanur reserve forest, Eastern Ghats, India.

Science.gov (United States)

Gandhi, Durai Sanjay; Sundarapandian, Somaiah

2017-04-01

Tropical dry forests are one of the most widely distributed ecosystems in tropics, which remain neglected in research, especially in the Eastern Ghats. Therefore, the present study was aimed to quantify the carbon storage in woody vegetation (trees and lianas) on large scale (30, 1 ha plots) in the dry deciduous forest of Sathanur reserve forest of Eastern Ghats. Biomass of adult (≥10 cm DBH) trees was estimated by species-specific allometric equations using diameter and wood density of species whereas in juvenile tree population and lianas, their respective general allometric equations were used to estimate the biomass. The fractional value 0.4453 was used to convert dry biomass into carbon in woody vegetation of tropical dry forest. The mean aboveground biomass value of juvenile tree population was 1.86 Mg/ha. The aboveground biomass of adult trees ranged from 64.81 to 624.96 Mg/ha with a mean of 245.90 Mg/ha. The mean aboveground biomass value of lianas was 7.98 Mg/ha. The total biomass of woody vegetation (adult trees + juvenile population of trees + lianas) ranged from 85.02 to 723.46 Mg/ha, with a mean value of 295.04 Mg/ha. Total carbon accumulated in woody vegetation in tropical dry deciduous forest ranged from 37.86 to 322.16 Mg/ha with a mean value of 131.38 Mg/ha. Adult trees accumulated 94.81% of woody biomass carbon followed by lianas (3.99%) and juvenile population of trees (1.20%). Albizia amara has the greatest biomass and carbon stock (58.31%) among trees except for two plots (24 and 25) where Chloroxylon swietenia contributed more to biomass and carbon stock. Similarly, Albizia amara (52.4%) showed greater carbon storage in juvenile population of trees followed by Chloroxylon swietenia (21.9%). Pterolobium hexapetalum (38.86%) showed a greater accumulation of carbon in liana species followed by Combretum albidum (33.04%). Even though, all the study plots are located within 10 km radius, they show a significant spatial variation among

Kinetics, biocompounds, antioxidant activity, and sensory attributes of quinces as affected by drying method.

Science.gov (United States)

Szychowski, Przemysław J; Lech, Krzysztof; Sendra-Nadal, Esther; Hernández, Francisca; Figiel, Adam; Wojdyło, Aneta; Carbonell-Barrachina, Ángel A

2018-07-30

Quinces are attracting interest due to their health and nutritional benefits. Drying kinetics, bioactive compounds, antioxidant activity, and the main sensory parameters were determined in dried quinces, cultivar Leskovač, as affected by the drying method. The highest total polyphenols content was observed in dried samples obtained after freeze drying and convective drying at 50 °C. The best drying treatment, considering only sensory attributes, was vacuum-microwave drying at 480 W, because it led to intermediate dark color and high intensities of basic tastes and key flavor attributes. The studied parameters were finally used to recommend convective drying at 60 °C as the most appropriate drying method for quinces, because it had a high content of total phenolic compounds (2nd best treatment out of 10), a good sensory profile, was cheap, and caused no negative effects on nutritional or sensory parameters; the only disadvantage was its long drying time. Copyright © 2018 Elsevier Ltd. All rights reserved.

Modeling of NO and N2O emissions from biomass circulating fluidized bed combustors

International Nuclear Information System (INIS)

Liu, H.; Gibbs, B.M.

2002-01-01

In order to correctly model biomass combustion in a circulating fluidized bed (CFB) combustor, it is necessary to examine the four main stages in the combustion of biomass particles. These include drying, devolatilization, volatile combustion and char combustion in a CFB combustor. This paper presents a newly developed model for nitric oxide (NO) and nitrous oxide (N 2 O) emissions from biomass-fired CFB combustors. A typical woody biomass of pinewood chips was selected for the model parameters. The drying and devolatilization of biomass particles was modeled with limited rates according to woody biomass fuels. The partition of fuel nitrogen between volatiles and char was chosen for pinewood based on available data from literature. It was assumed that the volatile nitrogen was composed of ammonia (NH 3 ), hydrogen cyanide (HCN) and nitrogen (N 2 ). The model included 25 chemical reactions, of which 20 belonged to global fuel-nitrogen reaction kinetics. A 12 MW CFB boiler was used to apply the model. Results were compared with experimental values as well as data from literature. The reaction between NO and char was found to be the key reaction that determines NO emissions. The catalytic effect of bed materials on the oxidation of NH 3 and the the homogeneous reaction of NH 3 with nitric oxide was also significant. 25 refs., 2 tabs., 5 figs

Direct Biodiesel Production from Wet Microalgae Biomass of Chlorella pyrenoidosa through In Situ Transesterification

Science.gov (United States)

Cao, Hechun; Zhang, Zhiling; Wu, Xuwen; Miao, Xiaoling

2013-01-01

A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production. PMID:24195081

Direct Biodiesel Production from Wet Microalgae Biomass of Chlorella pyrenoidosa through In Situ Transesterification

Directory of Open Access Journals (Sweden)

Hechun Cao

2013-01-01

Full Text Available A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production.

Direct biodiesel production from wet microalgae biomass of Chlorella pyrenoidosa through in situ transesterification.

Science.gov (United States)

Cao, Hechun; Zhang, Zhiling; Wu, Xuwen; Miao, Xiaoling

2013-01-01

A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production.

A stepwise-cluster microbial biomass inference model in food waste composting

International Nuclear Information System (INIS)

Sun Wei; Huang, Guo H.; Zeng Guangming; Qin Xiaosheng; Sun Xueling

2009-01-01

A stepwise-cluster microbial biomass inference (SMI) model was developed through introducing stepwise-cluster analysis (SCA) into composting process modeling to tackle the nonlinear relationships among state variables and microbial activities. The essence of SCA is to form a classification tree based on a series of cutting or mergence processes according to given statistical criteria. Eight runs of designed experiments in bench-scale reactors in a laboratory were constructed to demonstrate the feasibility of the proposed method. The results indicated that SMI could help establish a statistical relationship between state variables and composting microbial characteristics, where discrete and nonlinear complexities exist. Significance levels of cutting/merging were provided such that the accuracies of the developed forecasting trees were controllable. Through an attempted definition of input effects on the output in SMI, the effects of the state variables on thermophilic bacteria were ranged in a descending order as: Time (day) > moisture content (%) > ash content (%, dry) > Lower Temperature (deg. C) > pH > NH 4 + -N (mg/Kg, dry) > Total N (%, dry) > Total C (%, dry); the effects on mesophilic bacteria were ordered as: Time > Upper Temperature (deg. C) > Total N > moisture content > NH 4 + -N > Total C > pH. This study made the first attempt in applying SCA to mapping the nonlinear and discrete relationships in composting processes.

Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass

Energy Technology Data Exchange (ETDEWEB)

Hansen, H.K.; Kristensen, I.V.; Ottosen, L.M.; Villumsen, A. [Dept. of Geology and Geotechnical Engineering, The Technical Univ. of Denmark, Lyngby (Denmark)

2001-07-01

Electroosmotic dewatering has been tested in laboratory cells for 4 different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material. Casagrande's coefficients for the three materials where determined at different water contents. In the electroosmotic experiments shown in this work chalk can be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM. The process was not optimised indicating that higher dry matter contents could be achieved. (orig.)

Growth characteristics and biomass production of kenaf | Tahery ...

African Journals Online (AJOL)

Parameters of height, diameter and internode were measured within four to six regular intervals of 10 to 15 days, while biomass production parameters of dry one meter stalk mass (DMSM), defoliated plant mass (DPM), one meter stalk mass (MSM) and fresh plant mass (FPM) were measured at harvest time. There was no ...

Gasification of peat and biomass in suspension. Turpeen ja biomassan suspensiokaasutus

Energy Technology Data Exchange (ETDEWEB)

Haukka, P.; Raiko, R.

1993-01-01

Gasification of peat and biomass in dilute particle-gas suspension has not been studied significantly in Finland, even though these fuels require drying, which often produces dry pulverized fuel. This report has concentrated on studying suitability of so-called two-stage entrained-bed gasification for peat and biomass. The gasification system consists of a pyrolysis reactor (entrained flow) and an adiabatic char combustor. Dry or almost dry fuel is fed into the hot flue gas stream coming from the char combustor. Gasification is based on flash pyrolysis in the dilute suspension flow. Residual char is separated from pyrolyzer gases in a gas cleaning device and fed back to the adiabatic combustor. In the combustor char is burned at high temperature to supply the heat required to support endothermic reactions occurring in the pyrolyzer. To study entrained-bed gasification two types of computer models were developed: steady state simulation model and kinetic pyrolyzer model. With the help of these computer models mass and energy balances of the gasifier can be solved and the main dimensions of the gasifier can be determined. Lack of proper kinetic parameters for fast pyrolysis of peat and biomass makes it more difficult to apply the kinetic model in practice. Quantitative data concerning fast pyrolysis in dilute gas-particle suspension are needed to be able to evaluate the performance of the suspension gasifier in more detail. Gasifier operation has been studied using three different levels for amounts of pyrolysis pro- ducts, nine pressure levels between 15-23 bars and five temperature levels between 800-1200 deg C. Furthermore, normal pressure performance was simulated. In addition to simulation studies product gas heating value was optimized

Effects of fuel properties on the natural downward smoldering of piled biomass powder: Experimental investigation

International Nuclear Information System (INIS)

He, Fang; Yi, Weiming; Li, Yongjun; Zha, Jianwen; Luo, Bin

2014-01-01

To validate the modeling of one-dimensional biomass smoldering and combustion, the effects of fuel type, moisture content and particle size on the natural downward smoldering of biomass powder have been investigated experimentally. A cylindrical reactor (inner size Φ26 cm × 22 cm) was constructed, and corn stalk, pine trunk, pyrolysis char and activated char from corn stalk were prepared as powders. The smoldering characteristics were examined for each of the four materials and for different moisture contents and particle sizes. The results revealed the following: 1) The maximum temperature in the fuel bed is only slightly affected by the fuel type and particle size. It increases gradually for original biomass and decreases slowly for chars with the development of the process. 2) The propagation velocity of the char oxidation front is significantly affected by the carbon density and ash content and nearly unaffected by moisture content and particle size. 3) The propagation velocity of the drying front is significantly affected by the moisture content, decreasing from over 10 times the propagation velocity of char oxidation front to about 3 times as the moisture content increased from 3 to 21%. - Highlights: • Natural downward smoldering of four materials, different moisture contents, and different particle sizes were investigated. • Propagation velocity of the char oxidation front differs significantly from that of the drying front. • Carbon density and ash content of fuel significantly affect propagation velocity of the char oxidation front

Microbial responses to carbon and nitrogen supplementation in an Antarctic dry valley soil

DEFF Research Database (Denmark)

Dennis, P. G.; Sparrow, A. D.; Gregorich, E. G.

2013-01-01

The soils of the McMurdo Dry Valleys are exposed to extremely dry and cold conditions. Nevertheless, they contain active biological communities that contribute to the biogeochemical processes. We have used ester-linked fatty acid (ELFA) analysis to investigate the effects of additions of carbon...... and nitrogen in glucose and ammonium chloride, respectively, on the soil microbial community in a field experiment lasting three years in the Garwood Valley. In the control treatment, the total ELFA concentration was small by comparison with temperate soils, but very large when expressed relative to the soil...... organic carbon concentration, indicating efficient conversion of soil organic carbon into microbial biomass and rapid turnover of soil organic carbon. The ELFA concentrations increased significantly in response to carbon additions, indicating that carbon supply was the main constraint to microbial...

Finding Biomass Degrading Enzymes Through an Activity-Correlated Quantitative Proteomics Platform (ACPP)

Science.gov (United States)

Ma, Hongyan; Delafield, Daniel G.; Wang, Zhe; You, Jianlan; Wu, Si

2017-04-01

The microbial secretome, known as a pool of biomass (i.e., plant-based materials) degrading enzymes, can be utilized to discover industrial enzyme candidates for biofuel production. Proteomics approaches have been applied to discover novel enzyme candidates through comparing protein expression profiles with enzyme activity of the whole secretome under different growth conditions. However, the activity measurement of each enzyme candidate is needed for confident "active" enzyme assignments, which remains to be elucidated. To address this challenge, we have developed an Activity-Correlated Quantitative Proteomics Platform (ACPP) that systematically correlates protein-level enzymatic activity patterns and protein elution profiles using a label-free quantitative proteomics approach. The ACPP optimized a high performance anion exchange separation for efficiently fractionating complex protein samples while preserving enzymatic activities. The detected enzymatic activity patterns in sequential fractions using microplate-based assays were cross-correlated with protein elution profiles using a customized pattern-matching algorithm with a correlation R-score. The ACPP has been successfully applied to the identification of two types of "active" biomass-degrading enzymes (i.e., starch hydrolysis enzymes and cellulose hydrolysis enzymes) from Aspergillus niger secretome in a multiplexed fashion. By determining protein elution profiles of 156 proteins in A. niger secretome, we confidently identified the 1,4-α-glucosidase as the major "active" starch hydrolysis enzyme (R = 0.96) and the endoglucanase as the major "active" cellulose hydrolysis enzyme (R = 0.97). The results demonstrated that the ACPP facilitated the discovery of bioactive enzymes from complex protein samples in a high-throughput, multiplexing, and untargeted fashion.

Brief review: Preparation techniques of biomass based activated carbon monolith electrode for supercapacitor applications

Science.gov (United States)

Taer, Erman; Taslim, Rika

2018-02-01

The synthesis of activated carbon monolith electrode made from a biomass material using the hydrolytic pressure or the pelletization technique of pre-carbonized materials is one of standard reported methods. Several steps such as pre-carbonization, milling, chemical activation, hydraulic press, carbonization, physical activation, polishing and washing need to be accomplished in the production of electrodes by this method. This is relatively a long process that need to be simplified. In this paper we present the standard method and proceed with the introduction to several alternative methods in the synthesis of activated carbon monolith electrodes. The alternative methods were emphasized on the selection of suitable biomass materials. All of carbon electrodes prepared by different methods will be analyzed for physical and electrochemical properties. The density, degree of crystallinity, surface morphology are examples for physical study and specific capacitance was an electrochemical properties that has been analysed. This alternative method has offered a specific capacitance in the range of 10 to 171 F/g.

Effects of Nitrogen and Desferal Treatments on CROTALARIA's (Crotalaria juncea Roth) Biomass Production

Science.gov (United States)

László Phd, M., ,, Dr.

2009-04-01

920-920 individual plants. Experimental datas were estimated by MANOVA of SPSS. The most important results can be summarised as follows: a., As the N supplies improved the root length (cm), plant height (cm), mean scores (1-5), fresh root weight (t ha-1), green straw+leaf weight (t ha-1), total green biomass weight (t ha-1), air dry root weight (t ha-1), air dry straw+leaf weight (t ha-1), and total air dry biomass weight (t ha-1) increased with an 1.4, 1.3, 4.3, 1.3, 1.8, 1.6, 2.1, 1.9 and 2.0 times compared to the control by the start of flowering. b., As the N doses rised the root length, plant height, mean scores, fresh root weight, green straw+leaf weight, total green biomass weight, air dry root weight, air dry straw+leaf weight and total air dry biomass weight reaching 34.3 cm, 168.0 cm, 4.3, 14.8 t ha-1, 51.7 t ha-1, 66.5 t ha-1, 7.4 t ha-1, 16.5 t ha-1 and 23.9 t ha-1. c., About three-fourth of the total green biomass and total air dry biomass production at harvest was given by the straw+leaf yield, which ranged between 29.0-51.7 t ha-1 and 8.7-16.5 t ha-1, depending on the N-treatment applied. d., The root length, plant height, mean scores, fresh root weight, green straw+leaf weight, total green biomass weight, air dry root weight, air dry straw+leaf weight and total air dry biomass weight was increased in average with an 14, 15, 21, 157, 30, 63, 102, 28 and 51% by N+Desferal treatments compared to mean of N doses effects. e., By N+Desferal treatments the root length, plant height, mean scores, fresh root weight, green straw+leaf weight, total green biomass weight, air dry root weight, air dry straw+leaf weight and total air dry biomass weight achieved 37.0 cm, 173.3 cm, 4.3, 37.8 t ha-1, 64.4 t ha-1, 102.2 t ha-1, 13.8 t ha-1, 19.3 t ha-1 and 33.1 t ha-1. f., Approximately two-third of the total green biomass and total air dry biomass production at harvest was given by the straw+leaf yield, which ranged between 44.7-64.4 t ha-1 and 24.1-33.1 t ha-1

Accurate inference of shoot biomass from high-throughput images of cereal plants

Directory of Open Access Journals (Sweden)

Tester Mark

2011-02-01

Full Text Available Abstract With the establishment of advanced technology facilities for high throughput plant phenotyping, the problem of estimating plant biomass of individual plants from their two dimensional images is becoming increasingly important. The approach predominantly cited in literature is to estimate the biomass of a plant as a linear function of the projected shoot area of plants in the images. However, the estimation error from this model, which is solely a function of projected shoot area, is large, prohibiting accurate estimation of the biomass of plants, particularly for the salt-stressed plants. In this paper, we propose a method based on plant specific weight for improving the accuracy of the linear model and reducing the estimation bias (the difference between actual shoot dry weight and the value of the shoot dry weight estimated with a predictive model. For the proposed method in this study, we modeled the plant shoot dry weight as a function of plant area and plant age. The data used for developing our model and comparing the results with the linear model were collected from a completely randomized block design experiment. A total of 320 plants from two bread wheat varieties were grown in a supported hydroponics system in a greenhouse. The plants were exposed to two levels of hydroponic salt treatments (NaCl at 0 and 100 mM for 6 weeks. Five harvests were carried out. Each time 64 randomly selected plants were imaged and then harvested to measure the shoot fresh weight and shoot dry weight. The results of statistical analysis showed that with our proposed method, most of the observed variance can be explained, and moreover only a small difference between actual and estimated shoot dry weight was obtained. The low estimation bias indicates that our proposed method can be used to estimate biomass of individual plants regardless of what variety the plant is and what salt treatment has been applied. We validated this model on an independent

Effect of freeze-drying on the antioxidant compounds and antioxidant activity of selected tropical fruits.

Science.gov (United States)

Shofian, Norshahida Mohamad; Hamid, Azizah Abdul; Osman, Azizah; Saari, Nazamid; Anwar, Farooq; Dek, Mohd Sabri Pak; Hairuddin, Muhammad Redzuan

2011-01-01

The effects of freeze-drying on antioxidant compounds and antioxidant activity of five tropical fruits, namely starfruit (Averrhoa carambola L.), mango (Mangifera indica L.), papaya (Carica papaya L.), muskmelon (Cucumis melo L.), and watermelon Citruluss lanatus (Thunb.) were investigated. Significant (p dried fruit samples, except muskmelon. There was no significant (p > 0.05) change, however, observed in the ascorbic acid content of the fresh and freeze-dried fruits. Similarly, freeze-drying did not exert any considerable effect on β-carotene concentration of fruits, except for mango and watermelon, where significantly (p dried fruits. Overall, in comparison to β-carotene and ascorbic acid, a good correlation was established between the result of TPC and antioxidant assays, indicating that phenolics might have been the dominant compounds contributing towards the antioxidant activity of the fruits tested.

A comparison of wet and dry season ozone and CO over Brazil using in situ and satellite measurements

International Nuclear Information System (INIS)

Watson, C.E.; Fishman, J.; Gregory, G.L.; Sachse, G.W.

1991-01-01

Several field experiments have measured the regional effects of biomass burning. Two such experiments, designed to understand the chemistry of the Amazon rainforest during both the wet season and dry season, were conducted in the Amazon Basin. The first experiment, ABLE-2A (Amazon Boundary Layer Experiment), took place from July to August 1985, the early dry season, when biomass burning was just beginning. The second experiment, ABLE-2B, took place during the wet season, from April to May 1987, when little biomass burning was occurring. Comparing ABLE ozone data with tropospheric ozone concentrations derived from satellite data, using the method described by Fishman et al., shows a strong correlation between the direct measurements and the derived ozone concentrations, as well as a direct correlation of both to biomass burning. This comparison gives credence to the use of space-based platforms to monitor global chemistry and, in this case, the regional effects of biomass burning

Modelling of biomass pyrolysis

International Nuclear Information System (INIS)

Kazakova, Nadezhda; Petkov, Venko; Mihailov, Emil

2015-01-01

Pyrolysis is an essential preliminary step in a gasifier. The first step in modelling the pyrolysis process of biomass is creating a model for the chemical processes taking place. This model should describe the used fuel, the reactions taking place and the products created in the process. The numerous different polymers present in the organic fraction of the fuel are generally divided in three main groups. So, the multistep kinetic model of biomass pyrolysis is based on conventional multistep devolatilization models of the three main biomass components - cellulose, hemicelluloses, and lignin. Numerical simulations have been conducted in order to estimate the influence of the heating rate and the temperature of pyrolysis on the content of the virgin biomass, active biomass, liquid, solid and gaseous phases at any moment. Keywords: kinetic models, pyrolysis, biomass pyrolysis.

Growth, biomass production and photosynthesis of Cenchrus ciliaris L. under Acacia tortilis (Forssk.) Hayne based silvopastoral systems in semi arid tropics.

Science.gov (United States)

Mishra, A K; Tiwari, H S; Bhatt, R K

2010-11-01

The growth, biomass production and photosynthesis of Cenchrus ciliaris was studied under the canopies of 17 yr old Acacia tortilis trees in semi arid tropical environment. On an average the full grown canopy of A. tortilis at the spacing of 4 x 4 m allowed 55% of total Photosynthetically Active Radiation (PAR) which in turn increased Relative Humidity (RH) and reduced under canopy temperature to -1.75 degrees C over the open air temperature. C. ciliaris attained higher height under the shade of A. tortilis. The tiller production and leaf area index decreased marginally under the shade of tree canopies as compared to the open grown grasses. C. ciliaris accumulated higher chlorophyll a and b under the shade of tree canopies indicating its shade adaptation potential. The assimilatory functions such as rate of photosynthesis, transpiration, stomatal conductance, photosynthetic water use efficiency (PN/TR) and carboxylation efficiency (PN/CINT) decreased under the tree canopies due to low availability of PAR. The total biomass production in term of fresh and dry weight decreased under the tree canopies. On average of 2 yr C. ciliaris had produced 12.78 t ha(-1) green and 3.72 -t ha(-1) dry biomass under the tree canopies of A. tortilis. The dry matter yield reduced to 38% under the tree canopies over the open grown grasses. The A. tortilis + C. ciliaris maintained higher soil moisture, organic carbon content and available N P K for sustainable biomass production for the longer period. The higher accumulation of crude protein, starch, sugar and nitrogen in leaves and stem of C. ciliaris indicates that this grass species also maintained its quality under A. tortilis based silvopastoral system. The photosynthesis and dry matter accumulation are closely associated with available PAR indicating that for sustainable production of this grass species in the silvopasture systems for longer period about 55% or more PAR is required.

Biosorption of lead (II and copper (II by biomass of some marine algae

Directory of Open Access Journals (Sweden)

Chaisuksant, Y.

2004-09-01

Full Text Available Biosorption of heavy metal ions by algae is a potential technology for treating wastewater contaminated with heavy metals. Adsorption of lead (II and copper (II in aqueous solutions by some marine algae available in large quantities in Pattani Bay including Gracilaria fisheri, Ulva reticulata and Chaetomorpha sp. were investigated. The effect of pH on metal sorption of the algal biomass and the metal uptake capacity of the algal biomass comparing to that of synthetic adsorbents including activated carbon and siliga gel were studied by using batch equilibrium experiments. Each dried adsorbent was stirred in metal ions solutions with different pH or different concentration at room temperature for 24 hours and the residual metal ions were analysed using atomic absorption spectrophotometer. The initial concentrations of lead and copper ionswere 70 µg/l and 20 mg/l, respectively. It was found that the effect of pH on metal sorption was similar in each algal biomass. The metal uptake capacity increased as pH of the solution increased from 2.0 to 4.0 and reached a plateau at pH 5.0-7.0. The metal uptake capacities of each algal biomass were similar. At low concentrations of metal ions, the metal adsorption occurred rapidly while at higher metal concentration less metal adsorption by each algal biomass was observed. The metal adsorption of activated carbon and silica gel occurred gradually and was less than those of algal biomass. The equilibrium data of copper and lead ions fitted well to the Langmuir and Freundlich isotherm models. The maximum sorption capacity (Qm values (mean±SD of Chaetomorpha sp., U. reticulata, G. fisheri, activated carbon and silica gel for lead ions were 1.26±0.14, 1.19±0.14, 1.18±0.15, 1.14±0.11 and 1.15±0.12 mg/g, respectively. For copper adsorption, the Qm values for G. fisheri, U. reticulata and Chaetomorpha biomass were 15.87±1.03, 14.71±1.02 and 12.35± 1.03 mg/g, respectively. While those of activated carbon and

Fabrication and application of advanced functional materials from lignincellulosic biomass

Science.gov (United States)

Hu, Sixiao

This dissertation explored the conversion of lignocellulosic biomass into advanced functional materials and their potential applications. Lignocellulosic biomass represents an as-of-yet underutilized renewable source for not only biofuel production but also functional materials fabrication. This renewable source is a great alternative for fossil fuel based chemicals, which could be one of the solutions to energy crisis. In this work, it was demonstrated a variety of advanced materials including functional carbons, metal and silica nanoparticles could be derived from lignocellulosic biomass. Chapter 1 provided overall reviewed of the lignin structures, productions and its utilizations as plastics, absorbents and carbons, as well as the preparation of nano-structured silver, silica and silicon carbide/nitride from biomass. Chapter 2, 3 and 4 discussed the fabrication of highly porous carbons from isolated lignin, and their applications as electric supercapacitors for energy storage. In chapter 2, ultrafine porous carbon fibers were prepared via electrospinning followed by simultaneous carbonization and activation. Chapter 3 covered the fabrication of supercapacitor based on the porous carbon fibers and the investigation of their electrochemical performances. In chapter 4, porous carbon particulates with layered carbon nano plates structures were produced by simple oven-drying followed by simultaneous carbonization and activation. The effects of heat processing parameters on the resulting carbon structures and their electrochemical properties were discussed in details. Chapter 5 and 6 addressed the preparation of silver nanoparticles using lignin. Chapter 5 reported the synthesis, underlying kinetics and mechanism of monodispersed silver nanospheres with diameter less than 25 nm in aqueous solutions using lignin as dual reducing and capping agents. Chapter 6 covered the preparation of silver nanoparticles on electrospun celluloses ultrafine fibers using lignin as both

Biomass Feedstock and Conversion Supply System Design and Analysis

Energy Technology Data Exchange (ETDEWEB)

Jacobson, Jacob J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Roni, Mohammad S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Lamers, Patrick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cafferty, Kara G. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-09-01

Idaho National Laboratory (INL) supports the U.S. Department of Energy’s bioenergy research program. As part of the research program INL investigates the feedstock logistics economics and sustainability of these fuels. A series of reports were published between 2000 and 2013 to demonstrate the feedstock logistics cost. Those reports were tailored to specific feedstock and conversion process. Although those reports are different in terms of conversion, some of the process in the feedstock logistic are same for each conversion process. As a result, each report has similar information. A single report can be designed that could bring all commonality occurred in the feedstock logistics process while discussing the feedstock logistics cost for different conversion process. Therefore, this report is designed in such a way that it can capture different feedstock logistics cost while eliminating the need of writing a conversion specific design report. Previous work established the current costs based on conventional equipment and processes. The 2012 programmatic target was to demonstrate a delivered biomass logistics cost of $55/dry ton for woody biomass delivered to fast pyrolysis conversion facility. The goal was achieved by applying field and process demonstration unit-scale data from harvest, collection, storage, preprocessing, handling, and transportation operations into INL’s biomass logistics model. The goal of the 2017 Design Case is to enable expansion of biofuels production beyond highly productive resource areas by breaking the reliance of cost-competitive biofuel production on a single, low-cost feedstock. The 2017 programmatic target is to supply feedstock to the conversion facility that meets the in-feed conversion process quality specifications at a total logistics cost of $80/dry T. The $80/dry T. target encompasses total delivered feedstock cost, including both grower payment and logistics costs, while meeting all conversion in-feed quality targets

Nontraditional Use of Biomass at Certified Forest Management Units: Forest Biomass for Energy Production and Carbon Emissions Reduction in Indonesia

Directory of Open Access Journals (Sweden)

Asep S. Suntana

2012-01-01

Full Text Available Biomass conversion technologies that produce energy and reduce carbon emissions have become more feasible to develop. This paper analyzes the potential of converting biomass into biomethanol at forest management units experiencing three forest management practices (community-based forest management (CBFM, plantation forest (PF, and natural production forest (NPF. Dry aboveground biomass collected varied considerably: 0.26–2.16 Mg/ha/year (CBFM, 8.08–8.35 Mg/ha/year (NPF, and 36.48–63.55 Mg/ha/year (PF. If 5% of the biomass was shifted to produce biomethanol for electricity production, the NPF and PF could provide continuous power to 138 and 2,762 households, respectively. Dedicating 5% of the biomass was not a viable option from one CBFM unit. However, if all biomasses were converted, the CBFM could provide electricity to 19–27 households. If 100% biomass from two selected PF was dedicated to biomethanol production: (1 52,200–72,600 households could be provided electricity for one year; (2 142–285% of the electricity demand in Jambi province could be satisfied; (3 all gasoline consumed in Jambi, in 2009, would be replaced. The net carbon emissions avoided could vary from 323 to 8,503 Mg when biomethanol was substituted for the natural gas methanol in fuel cells and from 294 to 7,730 Mg when it was used as a gasoline substitute.

Effects of model choice and forest structure on inventory-based estimations of Puerto Rican forest biomass

Science.gov (United States)

Thomas J. Brandeis; Maria Del Rocio; Suarez Rozo

2005-01-01

Total aboveground live tree biomass in Puerto Rican lower montane wet, subtropical wet, subtropical moist and subtropical dry forests was estimated using data from two forest inventories and published regression equations. Multiple potentially-applicable published biomass models existed for some forested life zones, and their estimates tended to diverge with increasing...

Removal of Cr(VI) from aqueous solution by fungal biomass

Energy Technology Data Exchange (ETDEWEB)

Ahluwalia, Sarabjeet Singh [Department of Biotechnology, General Shivdev Singh Diwan Gurbachan Singh Khalsa College, Patiala, Punjab (India); Goyal, Dinesh [Department of Biotechnology and Environmental Sciences, Thapar University, Patiala, Punjab (India)

2010-10-15

Chromium compounds are released by industrial processes including leather production, mining, petroleum refining, in textile industry and dyeing. They are a significant threat to the environment and public health because of their toxicity. Removal of hexavalent chromium by living biomass of different fungi was effective in the order of Aspergillus terricola>Aspergillus niger>Acremonium strictum>Aureobasidium pullulans>Paecilomyces variotii>Aspergillus foetidus>Cladosporium resinae>Phanerochaete chrysosporium. Non-living dried fungal biomass showed higher potential for metal removal than living cells. Among all fungi dead biomass of P. chrysosporium, C. resinae and P. variotii had the maximum specific chromium uptake capacity, which was 11.02, 10.69 and 10.35 mg/g of dry biomass respectively at pH 4.0-5.0 in batch sorption. Removal of Cr(VI) by P. chrysosporium from multi-metallic synthetic solution as well as chrome effluent was significant by bringing down the residual concentration to 0.1 mg/L in the effluent, which falls within the permissible range and its removal was not affected by the presence of other metal ions such as Fe, Zn and Ni. Fourier transform infrared spectral analysis revealed the presence of carboxylate (C=O) and amine (-NH{sup +}{sub 3}-NH{sup +}{sub 2}) functional groups commonly present on the cell surface of all fungi, with possible involvement in chromium binding. The result indicates that non-living fungal biomass either obtained as a by-product of fermentation industry or mass produced using inexpensive culture media can be used for bioremediation of Cr(VI) from chrome effluent on large scale. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Solid-state fermentation : modelling fungal growth and activity

NARCIS (Netherlands)

Smits, J.P.

1998-01-01

In solid-state fermentation (SSF) research, it is not possible to separate biomass quantitatively from the substrate. The evolution of biomass dry weight in time can therefore not be measured. Of the aiternatives to dry weight available, glucosamine content is most

Design and Performance Evaluation of a Solar Assisted Heat Pump Dryer Integrated with Biomass Furnace for Red Chilli

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performance of a solar assisted heat pump dryer integrated with biomass furnace has been designed and evaluated for drying red chillies, and drying kinetics of red chillies were evaluated. The red chillies were dried from 22 kg with moisture content of 4.26 db to moisture content of 0.08 db which needed 11 hours, with the average drying chamber temperature, drying chamber relative humidity, and an air mass flow rate of 70.5°C, 10.1%, and 0.124 kg/s, respectively, while the open sun drying needed 62 hours. Compared to open sun drying, this dryer yielded 82% saving in drying time. The drying rate, the specific moisture extraction rate, and thermal efficiency of the dryer were estimated in average to be about 1.57 kg/h, 0.14 kg/kWh, and 9.03%, respectively. Three mathematical models, the Newton, Henderson-Pabis, and Page models, were fitted to the experimental data on red chillies dried by solar assisted heat pump dryer integrated with biomass furnace and open sun drying. The performance of these models was evaluated by comparing the coefficient of determination (R2, mean bias error (MBE, and root mean-square error (RMSE. The Page model gave the best results for representing drying kinetics of red chillies.

21 CFR 344.12 - Ear drying aid active ingredient.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Ear drying aid active ingredient. 344.12 Section 344.12 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... alcohol 95 percent in an anhydrous glycerin 5 percent base. [65 FR 48905, Aug. 10, 2000] ...

Drying effect on flavonoid composition and antioxidant activity of immature kumquat.

Science.gov (United States)

Lou, Shyi-Neng; Lai, Yi-Chun; Huang, Jia-De; Ho, Chi-Tang; Ferng, Lin-Huei A; Chang, Yung-Chung

2015-03-15

A seven flavonoids in hot water extract of immature kumquat (Citrus japonica var. margarita) were identified and quantified (mg/100g fresh fruit): 3',5'-di-C-β-glucopyranosylphloretin (DGPP, 285.9 ± 2.9 mg/100g), acacetin 8-C-neohesperidoside (margaritene, 136.2 ± 2.6 mg/100g), acacetin 6-C-neohesperidoside (isomargaritene, 119.1 ± 1.8 mg/100g), fortunellin (acacetin 7-O-neohesperidoside, 28.5 ± 0.7 mg/100g), apigenin 8-C-neohesperidoside (16.9 ± 0.1mg/100g), poncirin (isosakuranetin 7-O-neohesperidoside, 5.1 ± 0.1mg/100g), and rhoifolin (apigenin 7-O-neohesperidoside, 2.0 ± 0.1mg/100g). When immature kumquat was dried at 110 and 130°C for 0.5h, the antioxidant activity, total phenolic content and identified flavonoids increased. The UV absorbance of browning products of immature kumquat dried at 130°C for 1.5h increased dramatically, while the identified flavonoids decreased. Therefore, it was concluded that drying below 130°C for 1.0 h, could release phenolic compounds, which resulted in the increasing antioxidant activity. Drying at 130°C for 1.5h, it might be due to the effect of formed browning products. Copyright © 2014 Elsevier Ltd. All rights reserved.

Qualitative and kinetic analysis of torrefaction of lignocellulosic biomass using DSC-TGA-FTIR

Directory of Open Access Journals (Sweden)

Bimal Acharya

2015-11-01

Full Text Available Torrefaction is a thermochemical conversion technique to improve the fuel properties of lignocellulosic biomass by treating at temperature 200 ℃-300 ℃ in the minimum oxygen environment for a reasonable residence time. In this study, thermal decomposition and thermal activities of miscanthus and wheat straw during the torrefaction at 200 ℃, 275 ℃, and 300 ℃ in a nitrogen environment for 45 minutes of residence time are analyzed in a simultaneous thermogravimetric analyzer (micro TGA with a differential scanning calorimetry (DSC, and a macro-TGA. The output of the micro TGA is fed into the Fourier transform infrared spectrometry (FTIR and qualitative analysis of the gaseous product is carried out. The composition of different gas products during the torrefaction of biomass are compared critically and kinetics were analyzed. It is found that the weight loss due to degradation of initial biomass in second stage (torrefaction process is a much faster conversion process than the weight loss process in the first stage (drying process. The weight loss of biomass increases with increase in the residence time and torrefaction treatment temperatures. The yield after torrefaction is a solid bio-coal product. The torrefied product were less reactive and has nearly 25% better heating value than the raw biomass. Between the two feedstocks studied, torrefied miscanthus proved to be a more stable fuel than the torrefied wheat straw. The major gaseous components observed during torrefaction are water, carbon dioxide, carbon monoxide, 1,2-Dibromethylene.

Understanding the Environmental and Climate Impacts of Biomass Burning in Northern Sub-Saharan Africa

Science.gov (United States)

Ichoku, Charles; Gatebe, Charles; Bolten, John; Policelli, Fritz; Habib, Shahid; Lee, Jejung; Wang, Jun; Wilcox, Eric; Adegoke, Jimmy

2011-01-01

The northern sub-Saharan African (NSSA) region, bounded on the north and south by the Sahara and the Equator, respectively, and stretching from the West to the East African coastlines, has one of the highest biomass-burning rates per unit land area among all regions of the world. Because of the high concentration and frequency of fires in this region, with the associated abundance of heat release and gaseous and particulate smoke emissions, biomass-burning activity is believed to be one of the drivers of the regional carbon and energy cycles, with serious implications for the water cycle. A new interdisciplinary research effort sponsored by NASA is presently being focused on the NSSA region, to better understand the possible connection between the intense biomass burning observed from satellite year after year across the region and the rapid depletion of the regional water resources, as exemplified by the dramatic drying of Lake Chad. A combination of remote sensing and modeling approaches is being utilized in investigating multiple regional surface, atmospheric, and water-cycle processes, and inferring possible links between them. In this presentation, we will discuss preliminary results as well as the path toward improved understanding'of the interrelationships and feedbacks between the biomass burning and the environmental change dynamics in the NSSA region.

Feeding activity of mussels Mytilus edulis related to near-bed currents and phytoplankton biomass

DEFF Research Database (Denmark)

Dolmer, Per

2000-01-01

The feeding activity of blue mussels Mytilus edulis was investigated in the field and related to near-bottom current velocities and the phytoplankton biomass in the near-bottom water layers for four days. The body content of Chl-a in mussels and their shell gap size were used as indices of filtra......The feeding activity of blue mussels Mytilus edulis was investigated in the field and related to near-bottom current velocities and the phytoplankton biomass in the near-bottom water layers for four days. The body content of Chl-a in mussels and their shell gap size were used as indices...... of filtration activity. During days 1 and 2 the near-bed current velocities were low (1.2-2.1 cm s(-1)), and the near-bed phytoplankton biomass was at the same time lower than near the water surface. Between 44 and 69% of the mussels had closed shells and accumulated only small amounts of Chl-a in the body....... During day 3 and day 4 the near-bed current velocities increased to 6.5 and 3.9 cm s(-1). respectively, and the Chl-a was homogeneously distributed in the water column. Now only 17 and 25% of the mussels had closed valves and they accumulated a larger amount of Chl-a. The actual population filtration...

Research in biomass production and utilization: Systems simulation and analysis

Science.gov (United States)

Bennett, Albert Stewart

There is considerable public interest in developing a sustainable biobased economy that favors support of family farms and rural communities and also promotes the development of biorenewable energy resources. This study focuses on a number of questions related to the development and exploration of new pathways that can potentially move us toward a more sustainable biobased economy. These include issues related to biomass fuels for drying grain, economies-of-scale, new biomass harvest systems, sugar-to-ethanol crop alternatives for the Upper Midwest U.S., biomass transportation, post-harvest biomass processing and double cropping production scenarios designed to maximize biomass feedstock production. The first section of this study considers post-harvest drying of shelled corn grain both at farm-scale and at larger community-scaled installations. Currently, drying of shelled corn requires large amounts of fossil fuel energy. To address future energy concerns, this study evaluates the potential use of combined heat and power systems that use the combustion of corn stover to produce steam for drying and to generate electricity for fans, augers, and control components. Because of the large capital requirements for solid fuel boilers and steam turbines/engines, both farm-scale and larger grain elevator-scaled systems benefit by sharing boiler and power infrastructure with other processes. The second and third sections evaluate sweet sorghum as a possible "sugarcane-like" crop that can be grown in the Upper Midwest. Various harvest systems are considered including a prototype mobile juice harvester, a hypothetical one-pass unit that separates grain heads from chopped stalks and traditional forage/silage harvesters. Also evaluated were post-harvest transportation, storage and processing costs and their influence on the possible use of sweet sorghum as a supplemental feedstock for existing dry-grind ethanol plants located in the Upper Midwest. Results show that the concept

Microbial Functional Diversity, Biomass and Activity as Affected by Soil Surface Mulching in a Semiarid Farmland.

Directory of Open Access Journals (Sweden)

Yufang Shen

Full Text Available Mulching is widely used to increase crop yield in semiarid regions in northwestern China, but little is known about the effect of different mulching systems on the microbial properties of the soil, which play an important role in agroecosystemic functioning and nutrient cycling. Based on a 4-year spring maize (Zea mays L. field experiment at Changwu Agricultural and Ecological Experimental Station, Shaanxi, we evaluated the responses of soil microbial activity and crop to various management systems. The treatments were NMC (no mulching with inorganic N fertilizer, GMC (gravel mulching with inorganic N fertilizer, FMC (plastic-film mulching with inorganic N fertilizer and FMO (plastic-film mulching with inorganic N fertilizer and organic manure addition. The results showed that the FMO soil had the highest contents of microbial biomass carbon and nitrogen, dehydrogenase activity, microbial activity and Shannon diversity index. The relative use of carbohydrates and amino acids by microbes was highest in the FMO soil, whereas the relative use of polymers, phenolic compounds and amines was highest in the soil in the NMC soil. Compared with the NMC, an increased but no significant trend of biomass production and nitrogen accumulation was observed under the GMC treatment. The FMC and FMO led a greater increase in biomass production than GMC and NMC. Compare with the NMC treatment, FMC increased grain yield, maize biomass and nitrogen accumulation by 62.2, 62.9 and 86.2%, but no significant difference was found between the FMO and FMC treatments. Some soil biological properties, i.e. microbial biomass carbon, microbial biomass nitrogen, being sensitive to the mulching and organic fertilizer, were significant correlated with yield and nitrogen availability. Film mulching over gravel mulching can serve as an effective measure for crop production and nutrient cycling, and plus organic fertilization additions may thus have improvements in the biological

Effective moisture diffusivity and activation energy of rambutan seed under different drying methods to promote storage stability

Science.gov (United States)

Ahmad, So'bah; Shamsul Anuar, Mohd; Saleena Taip, Farah; Shamsudin, Rosnah; M, Siti Roha A.

2017-05-01

The effects of two drying methods, oven and microwave drying on the effective moisture diffusivity and activation energy of rambutan seed were studied. Effective moisture diffusivity and activation energy are the main indicators used for moisture movement within the material. Hence, it is beneficial to determine an appropriate drying method to attain a final moisture content of rambutan seed that potentially could be used as secondary sources in the industry. An appropriate final moisture content will provide better storage stability that can extend the lifespan of the rambutan seed. The rambutan seeds were dried with two drying methods (oven and microwave) at two level of the process variables (oven temperature; 40°C and 60°C and microwave power; 250W and 1000W) at constant initial moisture contents. The result showed that a higher value of effective moisture diffusivity and less activation energy were observed in microwave drying compared to oven drying. This finding portrays microwave drying expedites the moisture removal to achieve the required final moisture content and the most appropriate drying method for longer storage stability for rambutan seed. With respect to the process variables; higher oven temperatures and lower microwave powers also exhibit similar trends. Hopefully, this study would provide a baseline data to determine an appropriate drying method for longer storage period for turning waste to by-products.

Biomass gasification in the Netherlands

Energy Technology Data Exchange (ETDEWEB)

Van der Drift, A. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

2013-07-15

This reports summarizes the activities, industries, and plants on biomass gasification in the Netherlands. Most of the initiatives somehow relate to waste streams, rather than clean biomass, which may seem logic for a densely populated country as the Netherlands. Furthermore, there is an increasing interest for the production of SNG (Substitute Natural Gas) from biomass, both from governments and industry.

Nitrogen utilization and biomass yield in trickle bed air biofilters.

Science.gov (United States)

Kim, Daekeun; Sorial, George A

2010-10-15

Nitrogen utilization and subsequent biomass yield were investigated in four independent lab-scale trickle bed air biofilters (TBABs) fed with different VOCs substrate. The VOCs considered were two aromatic (toluene, styrene) and two oxygenated (methyl ethyl ketone (MEK), methyl isobutyl ketone (MIBK)). Long-term observations of TBABs performances show that more nitrogen was required to sustain high VOC removal, but the one fed with a high loading of VOC utilized much more nitrogen for sustaining biomass yield. The ratio N(consumption)/N(growth) was an effective indicator in evaluating nitrogen utilization in the system. Substrate VOC availability in the system was significant in determining nitrogen utilization and biomass yield. VOC substrate availability in the TBAB system was effectively identified by using maximum practical concentrations in the biofilm. Biomass yield coefficient, which was driven from the regression analysis between CO(2) production rate and substrate consumption rate, was effective in evaluating the TBAB performance with respect to nitrogen utilization and VOC removal. Biomass yield coefficients (g biomass/g substrate, dry weight basis) were observed to be 0.668, 0.642, 0.737, and 0.939 for toluene, styrene, MEK, and MIBK, respectively. 2010 Elsevier B.V. All rights reserved.

Wastewater sludge fertilization: Biomass productivity and heavy metal bioaccumulation in two Salix species grown in southern Quebec (Canada)

International Nuclear Information System (INIS)

Teodorescu, T.I.; Labrecque, M.; Daigle, S.; Poisson, G.

1993-01-01

More than other kind of trees, fast growing tree species, such as willows, can profit from sludge application. While sludges are good fertilizers, they may also contain heavy metals which could reduce productivity and cause risks to the environment. The main aims of the present research were to study: (1) the production capacity of Salix discolor and Salix viminalis when supplied with various amounts of dried and pelleted sludge; (2) the uptake, and accumulation of heavy metals. Unrooted cuttings were planted on sandy soil in large plastic pots and grown in outdoors for 20-week period. Five doses of sludge were applied: equivalent of 200 (T1), 160 (T2), 120 (T3), 80 (T4) and 40 (T5) kg N per ha. Trees which received the largest amount of sludge showed the best growth results. The stem-branch biomass was significantly higher for Salix viminalis. The relationship between the total yield biomass Y (t/ha) and the rate of fertilization X (kg N/ha) is linear. The regression equations of prediction biomass production were established as following: Salix discolor Y = 1.807 + 0.037X and Salix viminalis Y = 2.578 + 0.042X. For both species, greatest stems-branch biomass per gram of N applied were produced by treatments 1 and 2. The amount of nitrogen per leaf area (N/LA) and per leaf dry weight (N/LW), were higher for Salix viminalis which leads us believe that its photosynthetic activity was better. The transfer coefficient did not vary between the species but was significantly different for Cd and Zn. The plants were able to absorb Cd and Zn but less of Ni, Hg and Cu and Pb. It was concluded that the dried and pelleted sludge can be a good fertilizer. The treatment is beneficial when Salix discolor and particulary Salix viminalis are used as vegetation filters for wastewater sludge purification and production purposes

In situ hydrogen, acetone, butanol, ethanol and microdiesel production by Clostridium acetobutylicum ATCC 824 from oleaginous fungal biomass.

Science.gov (United States)

Hassan, Elhagag Ahmed; Abd-Alla, Mohamed Hemida; Bagy, Magdy Mohamed Khalil; Morsy, Fatthy Mohamed

2015-08-01

An in situ batch fermentation technique was employed for biohydrogen, acetone, butanol, ethanol and microdiesel production from oleaginous fungal biomass using the anaerobic fermentative bacterium Clostridium acetobutylicum ATCC 824. Oleaginous fungal Cunninghamella echinulata biomass which has ability to accumulate up to 71% cellular lipid was used as the substrate carbon source. The maximum cumulative hydrogen by C. acetobutylicum ATCC 824 from crude C. echinulata biomass was 260 ml H2 l(-1), hydrogen production efficiency was 0.32 mol H2 mole(-1) glucose and the hydrogen production rate was 5.2 ml H2 h(-1). Subsequently, the produced acids (acetic and butyric acids) during acidogenesis phase are re-utilized by ABE-producing clostridia and converted into acetone, butanol, and ethanol. The total ABE produced by C. acetobutylicum ATCC 824 during batch fermentation was 3.6 g l(-1) from crude fungal biomass including acetone (1.05 g l(-1)), butanol (2.19 g l(-1)) and ethanol (0.36 g l(-1)). C. acetobutylicum ATCC 824 has ability to produce lipolytic enzymes with a specific activity 5.59 U/mg protein to hydrolyze ester containing substrates. The lipolytic potential of C. acetobutylicum ATCC 824 was used as a biocatalyst for a lipase transesterification process using the produced ethanol from ABE fermentation for microdiesel production. The fatty acid ethyl esters (microdiesel) generated from the lipase transesterification of crude C. echinulata dry mass was analyzed by GC/MS as 15.4% of total FAEEs. The gross energy content of biohydrogen, acetone, butanol, ethanol and biodiesel generated through C. acetobutylicum fermentation from crude C. echinulata dry mass was 3113.14 kJ mol(-1). These results suggest a possibility of integrating biohydrogen, acetone, butanol and ethanol production technology by C. acetobutylicum with microdiesel production from crude C. echinulata dry mass and therefore improve the feasibility and commercialization of bioenergy production

Controlling the excess heat from oxy-combustion of coal by blending with biomass

Energy Technology Data Exchange (ETDEWEB)

Haykiri-Acma, H.; Turan, A.Z.; Yaman, S.; Kucukbayrak, S. [Istanbul Technical University, Chemical and Metallurgical Engineering Faculty, Chemical Engineering Department, 34469, Maslak, Istanbul (Turkey)

2010-11-15

Two different biomass species such as sunflower seed shell and hazelnut shell were blended with Soma-Denis lignite to determine the effects of co-combustion on the thermal reactivity and the burnout of the lignite sample. For this purpose, Thermogravimetric Analysis and Differential Scanning Calorimetry techniques were applied from ambient to 900 C with a heating rate of 40 C/min under dry air and pure oxygen conditions. It was found that the thermal reactivities of the biomass materials and the lignite are highly different from each other under each oxidizing medium. On the other hand, the presence of biomass in the burning medium led to important influences not only on the burnout levels but also on the heat flows. The heat flow from the burning of lignite increased fivefold when the oxidizing medium was altered from dry air to pure oxygen. But, in case of co-combustion under oxygen, the excess heat arising from combustion of lignite could be reduced and this may be helpful to control the temperature of the combustion chamber. Based on this, co-combustion of coal/biomass blends under oxygen may be suggested as an alternative method to the ''Carbon Dioxide Recycle Method'' encountered in the oxyfuel combustion systems. (author)

Analysis of Indirectly Fired Gas Turbine for Wet Biomass Fuels Based on commercial micro gas turbine data

DEFF Research Database (Denmark)

Elmegaard, Brian; Qvale, Einar Bjørn

2002-01-01

energy, which has been the practice up to now, the low temperature exhaust gases after having served as drying agent, are lead out into the environment; a simple change of process integration that has a profound effect on the performance. Four different cycles have been studied. These are the Simple IFGT...... fueled by dry biomass assuming negligible pressure loss in the heat exchanger and the combustion chamber, the IFGT fueled with wet biomass (Wet IFGT) assuming no pressure losses, and finally both the Simple and the Wet IFGT incorporating typical data for pressure losses of commercially available micro...

Optimization of low energy sonication treatment for granular activated carbon colonizing biomass assessment.

Science.gov (United States)

Saccani, G; Bernasconi, M; Antonelli, M

2014-01-01

This study is aimed at optimizing a low energy sonication (LES) treatment for granular activated carbon (GAC)-colonizing biomass detachment and determination, evaluating detachment efficiency and the effects of ultrasound exposure on bacterial cell viability. GAC samples were collected from two filters fed with groundwater. Conventional heterotrophic plate count (HPC) and fluorescence microscopy with a double staining method were used to evaluate cell viability, comparing two LES procedures, without and with periodical bulk substitution. A 20 min LES treatment, with bulk substitution after cycles of 5 min as maximum treatment time, allowed to recover 87%/100% of attached biomass, protecting detached bacteria from ultrasound damaging effects. Observed viable cell inactivation rate was 6.5/7.9% cell/min, with membrane-compromised cell damage appearing to be even higher (11.5%/13.1% cell/min). Assessing bacterial detachment and damaging ultrasound effects, fluorescence microscopy turned out to be more sensitive compared to conventional HPC. The optimized method revealed a GAC-colonizing biomass of 9.9 x 10(7) cell/gGAC for plant 1 and 8.8 x 10(7) cell/gGAC for plant 2, 2 log lower than reported in literature. The difference between the two GAC-colonizing biomasses is higher in terms of viable cells (46.3% of total cells in plant 1 GAC-colonizing biomass compared to the 33.3% in plant 2). Studying influent water contamination through multivariate statistical analyses, apossible combined toxic and genotoxic effect of chromium VI and trichloroethylene was suggested as a reason for the lower viable cell fraction observed in plant 2 GAC-colonizing population.

Sorption of PAHs and PCBs to activated carbon: coal versus biomass-based quality.

Science.gov (United States)

Amstaetter, Katja; Eek, Espen; Cornelissen, Gerard

2012-04-01

The addition of activated carbon (AC) is an increasingly popular method for pollutant immobilization, and the AC material can be made of biomass or coal/fossil feedstock. The aim of the present study was to investigate whether there are differences between pollutant sorption to biomass and coal-based AC in the presence and absence of sediment. Through N(2) and CO(2) adsorption to probe surface area and pore size it was shown that the biomass-based AC had a stronger dominance of narrow pores in the size range 3.5-15Šthan the anthracite-based material. In the absence of sediment, sorption isotherms for the probe compounds pyrene and PCB-101 showed stronger sorption for the biomass-based AC (logarithmic Freundlich coefficients 8.15 for pyrene; 9.91 for PCB-101) than for the anthracite-based one (logarithmic Freundlich coefficients 7.20 and 9.70, respectively). In the presence of sediment, the opposite trend was observed, with the stronger sorption for anthracite-based AC. Thus, the presence of competing and/or pore-blocking sediment constituents reduces sorption to a larger extent for biomass-derived AC (factor of 5 for pyrene to almost 100 for PCB-101) than for anthracite-based AC (no reduction for pyrene to factor of 5 for PCB-101). This difference is tentatively attributed to the difference in pore size distribution, narrow pores being more prone to clogging, and could have implications for remediation feasibility with AC from different sources. Copyright © 2012 Elsevier Ltd. All rights reserved.

Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply, April 2005

Energy Technology Data Exchange (ETDEWEB)

None

2005-04-01

The purpose of this report is to determine whether the land resources of the United States are capable of producing a sustainable supply of biomass sufficient to displace 30 percent or more of the country’s present petroleum consumption – the goal set by the Biomass R&D Technical Advisory Committee in their vision for biomass technologies. Accomplishing this goal would require approximately 1 billion dry tons of biomass feedstock per year.

Biomass burning in the tropics: Impact on atmospheric chemistry and biogeochemical cycles

International Nuclear Information System (INIS)

Crutzen, P.J.; Andreae, M.O.

1990-01-01

Biomass burning is widespread, especially in the tropics. It serves to clear land for shifting cultivation, to convert forests to agricultural and pastoral lands, and to remove dry vegetation in order to promote agricultural productivity and the growth of higher yield grasses. Furthermore, much agricultural waste and fuel wood is being combusted, particularly in developing countries. Biomass containing 2 to 5 petagrams of carbon is burned annually (1 petagram = 10 15 grams), producing large amounts of trace gases and aerosol particles that play important roles in atmospheric chemistry and climate. Emissions of carbon monoxide and methane by biomass burning affect the oxidation efficiency of the atmosphere by reacting with hydroxyl radicals, and emissions of nitric oxide and hydrocarbons lead to high ozone concentrations in the tropics during the dry season. Large quantities of smoke particles are produced as well, and these can serve as cloud condensation nuclei. These particles may thus substantially influence cloud microphysical and optical properties, an effect that could have repercussions for the radiation budget and the hydrological cycle in the tropics. Widespread burning may also disturb biogeochemical cycles, especially that of nitrogen. About 50% of the nitrogen in the biomass fuel can be released as molecular nitrogen. This pyrodenitrification process causes a sizable loss of fixed nitrogen in tropical ecosystems, in the range of 10 to 20 teragrams per year (1 teragram = 10 12 grams)

Estimation of aerial biomass of Lychnophora ericoides (Mart.

Directory of Open Access Journals (Sweden)

Brunno Santana de Andrade

2007-07-01

Full Text Available For sustainable use of native plant species, knowledge of the amount of harvestable biomass is necessary. This study presents data on allometric relationships of Lychnophora ericoides Mart. (Asteraceae, an extractive resource in the Cerrado region of Brazil. On the Fazenda Água Limpa (15º 45'S, 47º 57'W of the Universidade de Brasilia, 38 individuals of this species were measured in the field, the parts above ground were harvested, separated into components and oven dried. The best regression equations to estimate biomass were geometric and the best fit was between total height and total biomass (r² = 0.923. The economically useful portions, the leaves and branches accounted for approximately 20% of total above ground dry weight, but when used as the dependent variable, the strength of the relationship decreased (r² = 0.694. The relationship between branch diameter and leaf biomass was similar to that between height and leaf dry weight (r² = 0.600. The relation between the number of leaves and their biomass was linear but weak. The development of these equations is the first step towards the implementation of plans for sustainable use of this species.Para o uso sustentável das espécies vegetais nativas o conhecimento da quantidade de biomassa disponível é necessário. O objetivo deste estudo foi verificar as relações alométricas para Lychnophora ericoides Mart., um recurso extrativista importante na região dos Cerrados. Na Fazenda Água Limpa da Universidade de Brasília, 38 indivíduos desta espécie foram medidas no campo, a parte aérea foi cortada, separada em componentes de folhas, galhos e tronco e estas componentes foram secas e pesadas. As melhores equações de regressão para estimar a biomassa foram geométricas e o melhor ajuste foi entre altura total e biomassa total (r² = 0,923. As partes economicamente exploradas, as folhas e ramos, contribuíram com aproximadamente 20% do peso seco total desta espécie, mas a equa

Application of epithermal neutron activation analysis to investigate accumulation and adsorption of mercury by Spirulina platensis biomass

International Nuclear Information System (INIS)

Mosulishvili, L.M.; Belokobyl'skij, A.I.; Khizanishvili, A.I.; Frontas'eva, M.V.; Kirkesali, E.I.; Aksenova, N.G.

2004-01-01

Epithermal neutron activation analysis was used to study interaction of blue-green alga Spirulina platensis with toxic metal mercury. Various concentrations of Hg(II) were added to cell cultures in a nutrient medium. The dynamics of accumulation of Hg was investigated over several days in relation to Spirulina biomass growth. The process of Hg adsorption by Spirulina biomass was studied in short-time experiments. The isotherm of adsorption was carried out in Freindlich coordinates. Natural Spirulina biomass has potential to be used in the remediation of sewage waters at Hg concentrations ∼100 μg/1

Application of Epithermal Neutron Activation Analysis to Investigate Accumulation and Adsorption of Mercury by Spirulina platensis Biomass

CERN Document Server

Mosulishvili, L M; Khizanishvili, A I; Frontasyeva, M V; Kirkesali, E I; Aksenova, N G

2004-01-01

Epithermal neutron activation analysis was used to study interaction of blue-green alga Spirulina platensis with toxic metal mercury. Various concentrations of Hg(II) were added to cell cultures in a nutrient medium. The dynamics of accumulation of Hg was investigated over several days in relation to Spirulina biomass growth. The process of Hg adsorption by Spirulina biomass was studied in short-time experiments. The isotherm of adsorption was carried out in Freindlich coordinates. Natural Spirulina biomass has potential to be used in the remediation of sewage waters at Hg concentrations \\sim 100 {\\mu}g/l.

Biomass - alternative renewable energy source to the fossil fuels

Directory of Open Access Journals (Sweden)

Koruba Dorota

2017-01-01

Full Text Available The article presents the fossil fuels combustion effects in terms of the dangers of increasing CO2 concentration in the atmosphere. Based on the bibliography review the negative impact of increased carbon dioxide concentration on the human population is shown in the area of the external environment, particularly in terms of the air pollution and especially the impact on human health. The paper presents biomass as the renewable energy alternative source to fossil fuels which combustion gives a neutral CO2 emissions and therefore should be the main carrier of primary energy in Poland. The paper presents the combustion heat results and humidity of selected dry wood pellets (pellets straw, energy-crop willow pellets, sawdust pellets, dried sewage sludge from two sewage treatment plants of the Holly Cross province pointing their energy potential. In connection with the results analysis of these studies the standard requirements were discussed (EN 14918:2010 “Solid bio-fuels-determination of calorific value” regarding the basic parameters determining the biomass energy value (combustion heat, humidity.

Respiration, microbial biomass and soil phosphatase activity in two agroecosystems and one forest in Turrialba, Costa Rica

Directory of Open Access Journals (Sweden)

Wuellins Durango

2015-06-01

Full Text Available In order to evaluate some microbiological and biochemical characteristics, a comparative study was carried out, as related to 3 different land uses in Ultisols located in Grano de Oro, Turrialba, Costa Rica. Three soil management systems were selected (two agroecosystems, coffee and coffee-banana and forest. In each farm, 4 composite soil samples were collected, on which microbial biomass and respiration, and phosphatase enzyme activity analysis were performed. The microbial biomass in forest was statistically higher (423 mg C kg-1 compared to those in agroecosystems coffee and coffee-banana (77 and 111 mg C kg-1 respectively. Microbial respiration did not show differences due to land management (580, 560 and 570 μg CO2 g-1.day-1 in coffee, coffee-banana and forest systems, respectively. It was also determined that the enzyme phosphatase activity in forest soils was statistically higher (4432 μg p-NP g-1.h-1. The data suggest that soil conditions in the forest favor greater microbial activity and phosphatase biomass, as compared to agricultural systems.

Uncertainty in the spatial distribution of tropical forest biomass: a comparison of pan-tropical maps.

Science.gov (United States)

Mitchard, Edward Ta; Saatchi, Sassan S; Baccini, Alessandro; Asner, Gregory P; Goetz, Scott J; Harris, Nancy L; Brown, Sandra

2013-10-26

Mapping the aboveground biomass of tropical forests is essential both for implementing conservation policy and reducing uncertainties in the global carbon cycle. Two medium resolution (500 m - 1000 m) pantropical maps of vegetation biomass have been recently published, and have been widely used by sub-national and national-level activities in relation to Reducing Emissions from Deforestation and forest Degradation (REDD+). Both maps use similar input data layers, and are driven by the same spaceborne LiDAR dataset providing systematic forest height and canopy structure estimates, but use different ground datasets for calibration and different spatial modelling methodologies. Here, we compare these two maps to each other, to the FAO's Forest Resource Assessment (FRA) 2010 country-level data, and to a high resolution (100 m) biomass map generated for a portion of the Colombian Amazon. We find substantial differences between the two maps, in particular in central Amazonia, the Congo basin, the south of Papua New Guinea, the Miombo woodlands of Africa, and the dry forests and savannas of South America. There is little consistency in the direction of the difference. However, when the maps are aggregated to the country or biome scale there is greater agreement, with differences cancelling out to a certain extent. When comparing country level biomass stocks, the two maps agree with each other to a much greater extent than to the FRA 2010 estimates. In the Colombian Amazon, both pantropical maps estimate higher biomass than the independent high resolution map, but show a similar spatial distribution of this biomass. Biomass mapping has progressed enormously over the past decade, to the stage where we can produce globally consistent maps of aboveground biomass. We show that there are still large uncertainties in these maps, in particular in areas with little field data. However, when used at a regional scale, different maps appear to converge, suggesting we can provide

Effect of fertilisation on biomass yield, ash and element uptake in SRC willow

DEFF Research Database (Denmark)

Ugilt Larsen, Søren; Jørgensen, Uffe; Kjeldsen, Jens Bonderup

2016-01-01

+0, 2) NPK120+0, 3) Slurry180+0, 4) NPK120+120, 5) NPK240+0, 6) Slurry360+0. Fertilization affected biomass yield significantly but interacted with rotation and clone. In first rotation, fertilization increased dry matter (DM) yield across clones significantly from 3.7 Mg ha−1 y−1 for Control0+0 to 6.......5, 6.4 and 5.6 for Slurry360+0, NPK120+120 and NPK240+0, respectively. In second rotation, yield increased from 6.2 Mg ha−1 y−1 to 8.8, 8.2, 7.8 and 7.4 for Slurry360+0, NPK240+0, Slurry180+0 and NPK120+120, respectively. Biomass dry matter yield per ha increased linearly at 15 kg kg−1 of applied total...

Equations for predicting biomass of six introduced tree species, island of Hawaii

Science.gov (United States)

Thomas H. Schukrt; Robert F. Strand; Thomas G. Cole; Katharine E. McDuffie

1988-01-01

Regression equations to predict total and stem-only above-ground dry biomass for six species (Acacia melanoxylon, Albizio falcataria, Eucalyptus globulus, E. grandis, E. robusta, and E. urophylla) were developed by felling and measuring 2- to 6-year-old...

Novel technology development through thermal drying of encapsulated Kluyveromyces marxianus in micro- and nano-tubular cellulose in lactose fermentation and its evaluation for food production.

Science.gov (United States)

Papapostolou, Harris; Servetas, Yiannis; Bosnea, Loulouda A; Kanellaki, Maria; Koutinas, Athanasios A

2012-12-01

A novel technology development based on the production of a low-cost starter culture for ripening of cheeses and baking is reported in the present study. The starter culture comprises thermally dried cells of Kluyveromyces marxianus encapsulated in micro- and nano-tubular cellulose. For production of a low-cost and effective biocatalyst, whey was used as raw material for biomass production and thermal drying methods (convective, conventional, and vacuum) were applied and evaluated at drying temperatures ranging from 35 to 60 °C. The effect of drying temperature of biocatalysts on fermentability of lactose and whey was evaluated. Storage stability and suitability of biocatalysts as a commercial starter cultures was also assessed and evaluated. All thermally dried biocatalysts were found to be active in lactose and whey fermentation. In all cases, there was sugar conversion ranging from 92 to 100 %, ethanol concentration of up to 1.47 % (v/v), and lactic acid concentrations ranged from 4.1 to 5.5 g/l. However, convective drying of the encapsulated cells of K. marxianus in micro- and nano-tubular cellulose was faster and a more effective drying method while drying at 42 °C appear to be the best drying temperature in terms of cell activity, ethanol, and lactic acid formation. Storage of the biocatalysts for 3 months at 4 °C proved maintenance of its activity even though fermentation times increased by 50-100 % compared with the fresh dried ones.

Analyzing and Comparing Biomass Feedstock Supply Systems in China: Corn Stover and Sweet Sorghum Case Studies

Directory of Open Access Journals (Sweden)

Lantian Ren

2015-06-01

Full Text Available This paper analyzes the rural Chinese biomass supply system and models supply chain operations according to U.S. concepts of logistical unit operations: harvest and collection, storage, transportation, preprocessing, and handling and queuing. In this paper, we quantify the logistics cost of corn stover and sweet sorghum in China under different scenarios. We analyze three scenarios of corn stover logistics from northeast China and three scenarios of sweet sorghum stalks logistics from Inner Mongolia in China. The case study estimates that the logistics cost of corn stover and sweet sorghum stalk to be $52.95/dry metric ton and $52.64/dry metric ton, respectively, for the current labor-based biomass logistics system. However, if the feedstock logistics operation is mechanized, the cost of corn stover and sweet sorghum stalk decreases to $36.01/dry metric ton and $35.76/dry metric ton, respectively. The study also includes a sensitivity analysis to identify the cost factors that cause logistics cost variation. Results of the sensitivity analysis show that labor price has the most influence on the logistics cost of corn stover and sweet sorghum stalk, with a variation of $6 to $12/dry metric ton.

Influence of particulate matter on microfouling biomass in the Arabian Sea

Digital Repository Service at National Institute of Oceanography (India)

Bhosle, N.B.; Nandakumar, K.; Wagh, A.B.

~ E :; :; 00 " " 200 '\\00 6001&. I&. Olslonc. from rne St>cre tn. miles! Leg , 0----4L~2 L~3 Leo .; Log $ Fig.3 Suspended matter (A), and particulate organic carbon (B) of surface seawater. and microfouling biomass as dry weight (C) and organic carbon...

Benthic invertebrate density, biomass, and instantaneous secondary production along a fifth-order human-impacted tropical river.

Science.gov (United States)

Aguiar, Anna Carolina Fornero; Gücker, Björn; Brauns, Mario; Hille, Sandra; Boëchat, Iola Gonçalves

2015-07-01

The aim of this study was to assess land use effects on the density, biomass, and instantaneous secondary production (IP) of benthic invertebrates in a fifth-order tropical river. Invertebrates were sampled at 11 stations along the Rio das Mortes (upper Rio Grande, Southeast Brazil) in the dry and the rainy season 2010/2011. Invertebrates were counted, determined, and measured to estimate their density, biomass, and IP. Water chemical characteristics, sediment heterogeneity, and habitat structural integrity were assessed in parallel. Total invertebrate density, biomass, and IP were higher in the dry season than those in the rainy season, but did not differ significantly among sampling stations along the river. However, taxon-specific density, biomass, and IP differed similarly among sampling stations along the river and between seasons, suggesting that these metrics had the same bioindication potential. Variability in density, biomass, and IP was mainly explained by seasonality and the percentage of sandy sediment in the riverbed, and not directly by urban or agricultural land use. Our results suggest that the consistently high degradation status of the river, observed from its headwaters to mouth, weakened the response of the invertebrate community to specific land use impacts, so that only local habitat characteristics and seasonality exerted effects.

Activation of protein kinase B (PKB/Akt) and risk of lung cancer among rural women in India who cook with biomass fuel

Energy Technology Data Exchange (ETDEWEB)

Roychoudhury, Sanghita; Mondal, Nandan Kumar; Mukherjee, Sayali; Dutta, Anindita; Siddique, Shabana; Ray, Manas Ranjan, E-mail: manasrray@rediffmail.com

2012-02-15

The impact of indoor air pollution (IAP) from biomass fuel burning on the risk of carcinogenesis in the airways has been investigated in 187 pre-menopausal women (median age 34 years) from eastern India who cooked exclusively with biomass and 155 age-matched control women from same locality who cooked with cleaner fuel liquefied petroleum gas. Compared with control, Papanicolau-stained sputum samples showed 3-times higher prevalence of metaplasia and 7-times higher prevalence of dysplasia in airway epithelial cell (AEC) of biomass users. Immunocytochemistry showed up-regulation of phosphorylated Akt (p-Akt{sup ser473} and p-Akt{sup thr308}) proteins in AEC of biomass users, especially in metaplastic and dysplastic cells. Compared with LPG users, biomass-using women showed marked rise in reactive oxygen species (ROS) generation and depletion of antioxidant enzyme, superoxide dismutase (SOD) indicating oxidative stress. There were 2–5 times more particulate pollutants (PM{sub 10} and PM{sub 2.5}), 72% more nitrogen dioxide and 4-times more particulate-laden benzo(a)pyrene, but no change in sulfur dioxide in indoor air of biomass-using households, and high performance liquid chromatography estimated 6-fold rise in the concentration of benzene metabolite trans,trans-muconic acid (t,t-MA) in urine of biomass users. Metaplasia and dysplasia, p-Akt expression and ROS generation were positively associated with PM and t,t-MA levels. It appears that cumulative exposure to biomass smoke increases the risk of lung carcinogenesis via oxidative stress-mediated activation of Akt signal transduction pathway. -- Highlights: ► Carcinogenesis in airway cells was examined in biomass and LPG using women. ► Metaplasia and dysplasia of epithelial cells were more prevalent in biomass users. ► Change in airway cytology was associated with oxidative stress and Akt activation. ► Biomass users had greater exposure to respirable PM, B(a)P and benzene. ► Cooking with biomass

Activation of protein kinase B (PKB/Akt) and risk of lung cancer among rural women in India who cook with biomass fuel

International Nuclear Information System (INIS)

Roychoudhury, Sanghita; Mondal, Nandan Kumar; Mukherjee, Sayali; Dutta, Anindita; Siddique, Shabana; Ray, Manas Ranjan

2012-01-01

The impact of indoor air pollution (IAP) from biomass fuel burning on the risk of carcinogenesis in the airways has been investigated in 187 pre-menopausal women (median age 34 years) from eastern India who cooked exclusively with biomass and 155 age-matched control women from same locality who cooked with cleaner fuel liquefied petroleum gas. Compared with control, Papanicolau-stained sputum samples showed 3-times higher prevalence of metaplasia and 7-times higher prevalence of dysplasia in airway epithelial cell (AEC) of biomass users. Immunocytochemistry showed up-regulation of phosphorylated Akt (p-Akt ser473 and p-Akt thr308 ) proteins in AEC of biomass users, especially in metaplastic and dysplastic cells. Compared with LPG users, biomass-using women showed marked rise in reactive oxygen species (ROS) generation and depletion of antioxidant enzyme, superoxide dismutase (SOD) indicating oxidative stress. There were 2–5 times more particulate pollutants (PM 10 and PM 2.5 ), 72% more nitrogen dioxide and 4-times more particulate-laden benzo(a)pyrene, but no change in sulfur dioxide in indoor air of biomass-using households, and high performance liquid chromatography estimated 6-fold rise in the concentration of benzene metabolite trans,trans-muconic acid (t,t-MA) in urine of biomass users. Metaplasia and dysplasia, p-Akt expression and ROS generation were positively associated with PM and t,t-MA levels. It appears that cumulative exposure to biomass smoke increases the risk of lung carcinogenesis via oxidative stress-mediated activation of Akt signal transduction pathway. -- Highlights: ► Carcinogenesis in airway cells was examined in biomass and LPG using women. ► Metaplasia and dysplasia of epithelial cells were more prevalent in biomass users. ► Change in airway cytology was associated with oxidative stress and Akt activation. ► Biomass users had greater exposure to respirable PM, B(a)P and benzene. ► Cooking with biomass increases cancer risk in

Impact of environmental conditions on biomass yield, quality, and bio-mitigation capacity of Saccharina latissima

DEFF Research Database (Denmark)

Bruhn, Annette; Tørring, Ditte Bruunshøj; Thomsen, Marianne

2016-01-01

of the EU Marine Strategy Framework Directive. Environmental factors determine the yield and quality of the cultivated seaweed biomass and, in return, the seaweed aquaculture affects the marine environment by nutrient assimilation. Consequently, site selection is critical for obtaining optimal biomass yield...... environmental conditions and cultivation success. The biomass yields fluctuated 10-fold between sites due to local variations in light and nutrient availability.Yields were generally low, i.e. up to 510 g fresh weight (FW) per meter seeded line; however, the dry matter contents of protein and high...

Analysis and co-ordination of the activities concerning gasification of biomass. Summary country report, Denmark and Norway

International Nuclear Information System (INIS)

Stoholm, P.; Olsen, A.

1996-11-01

The analysis summarises the coordination of activities concerning the gasification of biomass in Denmark and Norway. The total quantity of available biomass for energy production in Denmark corresponds to ca. 115 PJ of which ca. 40% is utilized - and this constitutes ca. 6% of the country's total energy consumption. The resulting energy from biomass is currently mostly used for heating purposes utilizing small wood/straw household or farm stoves in addition to ca. 100 district heating systems. There is a tendency to use biomass fuels for electric power production as in the case of all major waste incineration plants and about 10 fully or partly wood/straw-fired cogeneration plants which are found within the range of 2 -20 MWe. A table shows details of all Danish biomass gasification plants and information is given on the types of biomass, under the titles of residue products and energy crops, most relevant to energy production in Denmark. Data is presented on the consumption of renewable energy in Denmark, recalculated in fuel equivalents, and Danish national energy policy and related legislation are described. Information on Norway's use of biomass as fuel is given under the headings of primary consumption, biomass sources and use, legislation, and brief evaluations of commercial gasification plants, pilot and demonstration plants, and laboratory plants and studies. It has recently been decided to speed up the development of small-scale gasification plants for combined heat and electricity production using biomass as fuel in Denmark. Total Norwegian energy consumption is 25% higher than Denmark's, and biomass fuels cover only 3.6% of this. (ARW) 32 refs

An integrated process for the extraction of fuel and chemicals from marine macroalgal biomass

Science.gov (United States)

Trivedi, Nitin; Baghel, Ravi S.; Bothwell, John; Gupta, Vishal; Reddy, C. R. K.; Lali, Arvind M.; Jha, Bhavanath

2016-07-01

We describe an integrated process that can be applied to biomass of the green seaweed, Ulva fasciata, to allow the sequential recovery of four economically important fractions; mineral rich liquid extract (MRLE), lipid, ulvan, and cellulose. The main benefits of our process are: a) its simplicity and b) the consistent yields obtained from the residual biomass after each successive extraction step. For example, dry Ulva biomass yields ~26% of its starting mass as MRLE, ~3% as lipid, ~25% as ulvan, and ~11% as cellulose, with the enzymatic hydrolysis and fermentation of the final cellulose fraction under optimized conditions producing ethanol at a competitive 0.45 g/g reducing sugar. These yields are comparable to those obtained by direct processing of the individual components from primary biomass. We propose that this integration of ethanol production and chemical feedstock recovery from macroalgal biomass could substantially enhance the sustainability of marine biomass use.

Biomass production of Prosopis species (mesquite), Leucaena, and other leguminous trees grown under heat/drought stress

Energy Technology Data Exchange (ETDEWEB)

Felker, P.; Cannell, G.H.; Clark, P.R.; Osborn, J.F.; Nash, P.

1983-09-01

Leguminous trees were examined for use of hot/arid lands in field trials in the California Imperial Valley where July daily maximum temperatures are 42 degrees C (108 degrees F). Two field trials were carried out to rank 55 accessions in biomass per tree and to evaluate biomass production per unit area with four of the more productive accessions identified in earlier trials. The trial with 55 accessions compared Prosopis (mesquite) to widely recommended species for arid lands such as Leucaena leucocephala (K-8), Parkinsonia aculeata, and Prosopis tamarugo and to other drought adapted tree legume species of California/Arizona deserts such as Cercidium floridium and Olneya tesota. Prosopis selections were identified that had greater productivity than either Leucaena leucocephala (K-8) or Parkinsonia aculeata. The mean oven-dry biomass per accession ranged from 0.2 kg/tree for Prosospis tamarugo to 29 kg/tree for P. alba (0166) when measured 2 years from germination in the greenhouse. Clones were obtained from trees in this trial which had 45-56 kg/tree (oven-dry) in two seasons. The plots designed to measure biomass production per unit area were on a 1.5 m spacing and had productivities of 7, 11.2, 14.3, and 14.5 oven-dry T ha-1 yr-1 for P. glandulosa var torreyana (0001), P. alba (0163), P. chilensis (0009), and P. alba(0039), respectively, when measured 2 years from germination in the greenhouse. 30 references

Effect of Freeze-Drying on the Antioxidant Compounds and Antioxidant Activity of Selected Tropical Fruits

Directory of Open Access Journals (Sweden)

Muhammad Redzuan Hairuddin

2011-07-01

Full Text Available The effects of freeze-drying on antioxidant compounds and antioxidant activity of five tropical fruits, namely starfruit (Averrhoa carambola L., mango (Mangifera indica L., papaya (Carica papaya L., muskmelon (Cucumis melo L., and watermelon Citruluss lanatus (Thunb. were investigated. Significant (p < 0.05 differences, for the amounts of total phenolic compounds (TPC, were found between the fresh and freeze-dried fruit samples, except muskmelon. There was no significant (p > 0.05 change, however, observed in the ascorbic acid content of the fresh and freeze-dried fruits. Similarly, freeze-drying did not exert any considerable effect on β-carotene concentration of fruits, except for mango and watermelon, where significantly (p < 0.05 higher levels were detected in the fresh samples. The results of DPPH (2,2-diphenyl-1-picrylhydrazyl radical scavenging and reducing power assays revealed that fresh samples of starfruit and mango had relatively higher antioxidant activity. In case of linoleic acid peroxidation inhibition measurement, a significant (p < 0.05 but random variation was recorded between the fresh and freeze-dried fruits. Overall, in comparison to β-carotene and ascorbic acid, a good correlation was established between the result of TPC and antioxidant assays, indicating that phenolics might have been the dominant compounds contributing towards the antioxidant activity of the fruits tested.

Biomass in Latin America -- overview

International Nuclear Information System (INIS)

Park, W.R.

1993-01-01

The paper discusses the interest of the Organization of American States as a participant in this hemispheric conference on biomass, provides an introduction to the Latin American experience in biomass energy through open-quotes snapshotsclose quotes of various country activities, and concludes with a discussion of four conditions that form strong incentives for new north/south and south/north ventures in the biomass energy and chemical arena in this hemisphere

Utilization of fruit peels as carbon source for white rot fungi biomass production under submerged state bioconversion

Directory of Open Access Journals (Sweden)

Olorunnisola Kola Saheed

2016-04-01

Full Text Available The present generation of nutrient rich waste streams within the food and hospitality industry is inevitable and remained a matter of concern to stakeholders. Three white rot fungal strains were cultivated under submerged state bioconversion (SmB. Fermentable sugar conversion efficiency, biomass production and substrate utilization constant were indicators used to measure the success of the process. The substrates – banana peel (Bp, pineapple peel (PAp and papaya peel (Pp were prepared in wet and dried forms as substrates. Phanerochaete chrysosporium (P. chrysosporium, Panus tigrinus M609RQY, and RO209RQY were cultivated on sole fruit wastes and their composites. All fungal strains produced profound biomass on dry sole wet substrates, but wet composite substrates gave improved results. P. tigrinus RO209RQY was the most efficient in sugar conversion (99.6% on sole substrates while P. tigrinus M609RQY was efficient on composite substrates. Elevated substrate utilization constant (Ku and biomass production heralded wet composite substrates. P. chrysosporium was the most performing fungal strain for biomass production, while PApBp was the best composite substrate.

Genotoxic potential generated by biomass burning in the Brazilian Legal Amazon by Tradescantia micronucleus bioassay: a toxicity assessment study

Directory of Open Access Journals (Sweden)

Artaxo Paulo

2011-05-01

Full Text Available Abstract Background The Brazilian Amazon has suffered impacts from non-sustainable economic development, especially owing to the expansion of agricultural commodities into forest areas. The Tangará da Serra region, located in the southern of the Legal Amazon, is characterized by non-mechanized sugar cane production. In addition, it lies on the dispersion path of the pollution plume generated by biomass burning. The aim of this study was to assess the genotoxic potential of the atmosphere in the Tangará da Serra region, using Tradescantia pallida as in situ bioindicator. Methods The study was conducted during the dry and rainy seasons, where the plants were exposed to two types of exposure, active and passive. Results The results showed that in all the sampling seasons, irrespective of exposure type, there was an increase in micronucleus frequency, compared to control and that it was statistically significant in the dry season. A strong and significant relationship was also observed between the increase in micronucleus incidence and the rise in fine particulate matter, and hospital morbidity from respiratory diseases in children. Conclusions Based on the results, we demonstrated that pollutants generated by biomass burning in the Brazilian Amazon can induce genetic damage in test plants that was more prominent during dry season, and correlated with the level of particulates and elevated respiratory morbidity.

Effects of fire on soil nitrogen dynamics and microbial biomass in savannas of Central Brazil

Directory of Open Access Journals (Sweden)

Nardoto Gabriela Bielefeld

2003-01-01

Full Text Available The objective of this work was to study the effects of fire on net N mineralization and soil microbial biomass in burned and unburned cerrado stricto sensu sites. The study was carried out from April 1998 to April 2000. The pH values were significantly higher in the burned site while soil moisture content was significantly higher in the unburned site (P<0.05. The soil C/N ratio was 22/1 and the available NO3-N ranged between 1.5 and 2.8 mg kg-¹ dry weight. However, the NH4-N concentration ranged between 3 and 34 mg kg-1 dry weight in the burned site and between 3 and 22 mg kg-1 dry weight in the unburned site. The NH4-N increased after fire, but no significant changes were observed for NO3-N (P<0.05. The NO3-N accumulation occurred in short periods during the rainy season. The rates of net N mineralization increased during the rainy season while reductions in soil microbial biomass were observed at both sites. This suggested that the peak in microbial activities occurred with the first rain events, with an initial net immobilization followed by net mineralization. Both sites presented the same pattern for mineralization/immobilization, however, the amount of inorganic-N cycled annually in unburned site was 14.7 kg ha-1 per year while the burned site presented only 3.8 kg ha-¹ of inorganic-N, one year after the burning.

Opportunities for Green Gas. Competition of Green Gas with other Biomass Options

International Nuclear Information System (INIS)

Bergsma, G.C.; Croezen, H.J.

2011-04-01

Green biogas seems to be an interesting option to make the Dutch economy, with a large share of gas in the energy system, more sustainable. Biomass that is used as feedstock for biogas can also be deployed for the production of Electricity, biodiesel, bio-ethanol, bio-plastics, bio-chemical products and even bio-steel. This memo compares the main characteristics of biomass uses for production of gas with alternative uses in other sectors. The comparison shows that wet biomass flows in particular (e.g. manure and KGW) are suitable for conversion in biogas. This leads to a potential of 1 to 1.5 billion Nm 3 of gas in 2020. Gasification of dry biomass may also become interesting in the future. However, this fuel is subjected to fierce competition with the electricity sector, which can use solid biomass for combustion purposes. Moreover, the steel, chemical and transport sector may also be able to use the feedstock in time. [nl

Chemical characterization and antioxidant activities comparison in fresh, dried, stir-frying and carbonized ginger.

Science.gov (United States)

Li, Yuxin; Hong, Yan; Han, Yanquan; Wang, Yongzhong; Xia, Lunzhu

2016-02-01

Ginger (Zingiber officinale Rosc.) is a common dietary adjunct that contributes to the taste and flavor of foods, and is also an important Traditional Chinese medicine (TCM). Different processing methods can produce different processed gingers with dissimilar chemical constituents and pharmacological activities. In this study, an ultra-performance liquid chromatography/quadrupole-time-of-flight mass spectrometry (UPLC/QTOF-MS) was applied to identify the complicated components from fresh, dried, stir-frying and carbonized ginger extracts. All of the 27 compounds were identified from four kinds of ginger samples (fresh, dried, stir-frying and carbonized ginger). Five main constituents (zingerone, 6-gingerol, 8-gingerol, 6-shogaol and 10-gingerol) in these four kinds of ginger sample extracts were simultaneously determined by UPLC-PDA. Meanwhile, the antioxidant effect of fresh, dried, stir-frying and carbonized gingers were evaluated by three assays (2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azinobis(3-ethylbenzthiazolinesulfonic acid) diammonium salt (ABTS), and ferric reducing antioxidant power (FRAP)). The results demonstrated that antioxidant activity of dried ginger was the highest, for its phenolic contents are 5.2-, 1.1- and 2.4-fold higher than that of fresh, stir-frying and carbonized ginger, respectively, the antioxidant activities' results indicated a similar tendency with phenolic contents: dried ginger>stir-frying ginger>fresh ginger>carbonized ginger. The processing contributed to the decreased concentration of gingerols and the increased levels of shogaols, which reducing the antioxidant effects in pace with processing. This study elucidated the relationship of the heating process with the constituents and antioxidant activity, and provided a guide for choosing different kinds of ginger samples on clinical application. Copyright © 2016 Elsevier B.V. All rights reserved.

Above-ground biomass production and allometric relations of Eucalyptus globulus Labill. coppice plantations along a chronosequence in the central highlands of Ethiopia

International Nuclear Information System (INIS)

Zewdie, Mulugeta; Olsson, Mats; Verwijst, Theo

2009-01-01

Eucalyptus plantations are extensively managed for wood production in the central highlands of Ethiopia. Nevertheless, little is known about their biomass (dry matter) production, partitioning and dynamics over time. Data from 10 different Eucalyptus globulus stands, with a plantation age ranging from 11 to 60 years and with a coppice-shoot age ranging from 1 to 9 years were collected and analyzed. Above-ground tree biomass of 7-10 sampled trees per stand was determined destructively. Dry weights of tree components (W c ; leaves, twigs, branches, stembark, and stemwood) and total above-ground biomass (W a ) were estimated as a function of diameter above stump (D), tree height (H) and a combination of these. The best fits were obtained, using combinations of D and H. When only one explanatory variable was used, D performed better than H. Total above-ground biomass was linearly related to coppice-shoot age. In contrast a negative relation was observed between the above-ground biomass production and total plantation age (number of cutting cycles). Total above-ground biomass increased from 11 t ha -1 at a stand age of 1 year to 153 t ha -1 at 9 years. The highest dry weight was allocated to stemwood and decreased in the following order: stemwood > leaves > stembark > twigs > branches. The equations developed in this study to estimate biomass components can be applied to other Eucalyptus plantations under the assumption that the populations being studied are similar with regard to density and tree size to those for which the relationships were developed

Above-ground biomass production and allometric relations of Eucalyptus globulus Labill. coppice plantations along a chronosequence in the central highlands of Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Zewdie, Mulugeta; Olsson, Mats; Verwijst, Theo [Swedish University of Agricultural Sciences, Department of Crop Production Ecology, P.O. Box 7043, 75007 Uppsala (Sweden)

2009-03-15

Eucalyptus plantations are extensively managed for wood production in the central highlands of Ethiopia. Nevertheless, little is known about their biomass (dry matter) production, partitioning and dynamics over time. Data from 10 different Eucalyptus globulus stands, with a plantation age ranging from 11 to 60 years and with a coppice-shoot age ranging from 1 to 9 years were collected and analyzed. Above-ground tree biomass of 7-10 sampled trees per stand was determined destructively. Dry weights of tree components (W{sub c}; leaves, twigs, branches, stembark, and stemwood) and total above-ground biomass (W{sub a}) were estimated as a function of diameter above stump (D), tree height (H) and a combination of these. The best fits were obtained, using combinations of D and H. When only one explanatory variable was used, D performed better than H. Total above-ground biomass was linearly related to coppice-shoot age. In contrast a negative relation was observed between the above-ground biomass production and total plantation age (number of cutting cycles). Total above-ground biomass increased from 11 t ha{sup -1} at a stand age of 1 year to 153 t ha{sup -1} at 9 years. The highest dry weight was allocated to stemwood and decreased in the following order: stemwood > leaves > stembark > twigs > branches. The equations developed in this study to estimate biomass components can be applied to other Eucalyptus plantations under the assumption that the populations being studied are similar with regard to density and tree size to those for which the relationships were developed. (author)

Woody biomass production in a spray irrigation wastewater treatment facility in North Carolina

International Nuclear Information System (INIS)

Frederick, D.; Lea, R.; Milosh, R.

1993-01-01

Application of municipal wastewater to deciduous tree plantations offers a viable opportunity to dispose of nutrients and pollutants, while protecting water quality. Production of woody biomass for energy or pulp mill furnish, using wastewater if feasible and markets exist in may parts of the world for this biomass. Plantations of sycamore (Platanus occidentalis L.), and sweetgum (Liquidambar styraciflua L.), have been established in Edenton, North Carolina for application of municipal wastewater. Research describing the dry weight biomass following the fifth year of seedling growth is presented along with future estimates for seedling and coppice yields. Ongoing and future work for estimating nutrient assimilation and wastewater renovation are described and discussed

Source indicators of biomass burning associated with inorganic salts and carboxylates in dry season ambient aerosol in Chiang Mai Basin, Thailand

Science.gov (United States)

Tsai, Ying I.; Sopajaree, Khajornsak; Chotruksa, Auranee; Wu, Hsin-Ching; Kuo, Su-Ching

2013-10-01

PM10 aerosol was collected between February and April 2010 at an urban site (CMU) and an industrial site (TOT) in Chiang Mai, Thailand, and characteristics and provenance of water-soluble inorganic species, carboxylates, anhydrosugars and sugar alcohols were investigated with particular reference to air quality, framed as episodic or non-episodic pollution. Sulfate, a product of secondary photochemical reactions, was the major inorganic salt in PM10, comprising 25.9% and 22.3% of inorganic species at CMU and TOT, respectively. Acetate was the most abundant monocarboxylate, followed by formate. Oxalate was the dominant dicarboxylate. A high acetate/formate mass ratio indicated that primary traffic-related and biomass-burning emissions contributed to Chiang Mai aerosols during episodic and non-episodic pollution. During episodic pollution carboxylate peaks indicated sourcing from photochemical reactions and/or directly from traffic-related and biomass burning processes and concentrations of specific biomarkers of biomass burning including water-soluble potassium, glutarate, oxalate and levoglucosan dramatically increased. Levoglucosan, the dominant anhydrosugar, was highly associated with water-soluble potassium (r = 0.75-0.79) and accounted for 93.4% and 93.7% of anhydrosugars at CMU and TOT, respectively, during episodic pollution. Moreover, levoglucosan during episodic pollution was 14.2-21.8 times non-episodic lows, showing clearly that emissions from biomass burning are the major cause of PM10 episodic pollution in Chiang Mai. Additionally, the average levoglucosan/mannosan mass ratio during episodic pollution was 14.1-14.9, higher than the 5.73-7.69 during non-episodic pollution, indicating that there was more hardwood burning during episodic pollution. Higher concentrations of glycerol and erythritol during episodic pollution further indicate that biomass burning activities released soil biota from forest and farmland soils.

EnviroAtlas - Above Ground Live Biomass Carbon Storage for the Conterminous United States- Forested

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset includes the average above ground live dry biomass estimate for the Watershed Boundary Dataset (WBD) 12-digit Hydrologic Unit (HUC) in kg/m...

Fouling control in biomass boilers

Energy Technology Data Exchange (ETDEWEB)

Romeo, Luis M.; Gareta, Raquel [Centro de Investigacion de Recursos y Consumos Energeticos (CIRCE), Universidad de Zaragoza, Centro Politecnico Superior, Maria de Luna, 3, 50018 Zaragoza (Spain)

2009-05-15

One of the important challenges for biomass combustion in industrial applications is the fouling tendency and how it affects to the boiler performance. The classical approach for this question is to activate sootblowing cycles with different strategies to clean the boiler (one per shift, one each six hours..). Nevertheless, it has been often reported no effect on boiler fouling or an excessive steam consumption for sootblowing. This paper illustrates the methodology and the application to select the adequate time for activating sootblowing in an industrial biomass boiler. The outcome is a control strategy developed with artificial intelligence (Neural Network and Fuzzy Logic Expert System) for optimizing the biomass boiler cleaning and maximizing heat transfer along the time. Results from an optimize sootblowing schedule show savings up to 12 GWh/year in the case-study biomass boiler. Extra steam generation produces an average increase of turbine power output of 3.5%. (author)

Biosorption of lanthanides using three kinds of seaweed biomasses

International Nuclear Information System (INIS)

Sakamoto, Nobuo; Wang, Yudan; Gao, Lidi; Kano, Naoki; Imaizumi, Hiroshi

2010-01-01

In order to evaluate the efficiency of seaweed biomass as sorbent for rare earth elements (REEs), sorption experiment from aqueous solutions containing known amount of lanthanide (La, Eu or Yb) using three kinds of Ca-loaded dried seaweeds (brown algae: Sargassum hemiphyllum, green algae: Ulva pertusa and red algae: Schizymenia dubyi) in single component system was explored. Furthermore, the sorption mechanism of these elements was investigated by applying Langmuir and Freundlich isotherm equations to the data obtained. In addition, to confirm the characteristics of the seaweed biomasses, the surface morphology of the biomass before and after metal adsorption was determined by Scanning Electron Microscope (SEM). Consequently, the following matters have been mainly clarified. (1) The morphology of Sargassum hemiphyllum and Ulva pertusa surface has hardly changed even after exposing to metals. On the other hand, the change of the surface condition on Schizymenia dubyi after adsorption was observed. (2) Adsorption isotherms using the seaweed biomass can be described by Langmuir and Freundlich isotherms satisfactorily for lanthanide. These adsorption may have occurred mainly by monolayer reaction because of better-fitting for Langmuir model. (3) The seaweed biomasses could be an efficient sorbent for REEs. Particularly, Ulva pertusa is found to be a promising biosorbent for removing La. (4) Ion-exchange process is considered to be the main mechanism responsible for the sorption of lanthanide ion onto the seaweed biomass. (author)

Effect of biomass pretreatment on the product distribution and composition resulting from the hydrothermal liquefaction of short rotation coppice willow

DEFF Research Database (Denmark)

Grigoras, Ionela; Stroe, Rodica-Elisabeta; Sintamarean, Iulia-Maria

2017-01-01

A major challenge for the implementation of hydrothermal liquefaction (HTL) as a continuous process is the formulation of lignocellulosic feedstock, which is prone to phase separation into water and biomass parts when pressurized. One approach to remedy such phase separation is to reduce the dry...... from the HTL of willow and proposes short rotation coppice as an alternative biomass feedstock for biofuels production. Alkaline–thermal pretreatment, besides making high dry matter pumpable feedstock slurries, also led to an increase in the production of the bio-crude product with an oxygen content...

Instrumental neutron activation analysis of dry atmospheric fall-out and rain-water

International Nuclear Information System (INIS)

Schutyser, P.; Maenhaut, W.; Dams, R.

1978-01-01

An automated precipitation sampler and an instrumental neutron activation analysis (i.n.a.a.) method for the determination of some major and trace elements in dry atmospheric fall-out and rain-water are presented. The sampler features a rain detector which makes separate collections of dry atmospheric fall-out and rain-water possible. The sampler is equipped with u.v. lamps in order to avoid algal growth during extended collection periods. After collection, the samples are separated into water-soluble and insoluble fractions. The soluble fraction is preconcentrated before analysis by freeze-drying. The i.n.a.a. method involves the measurement of both short- and long-lived radioactivities so that a total of 35 elements can be determined. The possibility of losses during freeze-drying and the accuracy of the i.n.a.a. method were investigated for 7 elements by analysis of a soluble fraction with an independent method, viz. inductively coupled plasma atomic emission spectrometry. (Auth.)

Allometric Models Based on Bayesian Frameworks Give Better Estimates of Aboveground Biomass in the Miombo Woodlands

Directory of Open Access Journals (Sweden)

Shem Kuyah

2016-02-01

Full Text Available The miombo woodland is the most extensive dry forest in the world, with the potential to store substantial amounts of biomass carbon. Efforts to obtain accurate estimates of carbon stocks in the miombo woodlands are limited by a general lack of biomass estimation models (BEMs. This study aimed to evaluate the accuracy of most commonly employed allometric models for estimating aboveground biomass (AGB in miombo woodlands, and to develop new models that enable more accurate estimation of biomass in the miombo woodlands. A generalizable mixed-species allometric model was developed from 88 trees belonging to 33 species ranging in diameter at breast height (DBH from 5 to 105 cm using Bayesian estimation. A power law model with DBH alone performed better than both a polynomial model with DBH and the square of DBH, and models including height and crown area as additional variables along with DBH. The accuracy of estimates from published models varied across different sites and trees of different diameter classes, and was lower than estimates from our model. The model developed in this study can be used to establish conservative carbon stocks required to determine avoided emissions in performance-based payment schemes, for example in afforestation and reforestation activities.

Decomposition of fresh and anaerobically digested plant biomass in soil

International Nuclear Information System (INIS)

Moorhead, K.K.; Graetz, D.A.; Reddy, K.R.

1987-01-01

Using water hyacinth [Eichhornia crassipes (Mart.) Solms] for waste water renovation produces biomass that must be disposed of. This biomass may be anaerobically digested to produce CH 4 or added to soil directly as an amendment. In this study, fresh and anaerobically digested water hyacinth biomass, with either low or high N tissue content, were added to soil to evaluate C and N mineralization characteristics. The plant biomass was labeled with 15 N before digestion. The fresh plant biomass and digested biomass sludge were freeze-dried and ground to pass a 0.84-mm sieve. The materials were thoroughly mixed with a Kindrick fine sand at a rate of 5 g kg -1 soil and incubated for 90 d at 27 0 C at a moisture content adjusted to 0.01 MPa. Decomposition was evaluated by CO 2 evolution and 15 N mineralization. After 90 d, approximately 20% of the added C of the digested sludges had evolved as CO 2 compared to 39 and 50% of the added C of the fresh plant biomass with a low and high N content, respectively. First-order kinetics were used to describe decomposition stages. Mineralization of organic 15 N to 15 NO 3 - -N accounted for 8% of applied N for both digested sludges at 90 d. Nitrogen mineralization accounted for 3 and 33% of the applied organic N for fresh plant biomass with a low and high N content, respectively

Biomass as a fuel: Advantages, limitations and possibilities

International Nuclear Information System (INIS)

McBurney, B.

1997-01-01

This presentation briefly outlines major issues related to the use of biomass fuels. Advantages and disadvantages of biomass fuels are identified, as well as major factors that may facilitate greater use of biomass fuels. Highlights of the US DOE Biomass Power Program, program activities, and demonstration projects are presented. Some statistical and economic data are provided, including biomass fueled electric capacity, biomass energy consumption by sector, and fuel cost savings and greenhouse gas emissions reductions for four biomass co-fired units

Acetylcholinesterase inhibition and antibacterial activity of Mondia whitei adventitious roots and ex vitro-grown somatic embryogenic-biomass

Directory of Open Access Journals (Sweden)

Ponnusamy Baskaran

2016-10-01

Full Text Available Mondia whitei (Hook.f. Skeels is an important endangered medicinal and commercial plant in South Africa. In vitro propagation systems are required for biomass production and bioactivity analysis to supplement wild resources/stocks. Adventitious roots from somatic embryogenic explants using suspension culture and ex vitro-grown plants produced via somatic embryogenesis were established using different plant growth regulator treatments. The adventitious root biomass and different parts of ex vitro-grown and mother plants were used to investigate the potential for acetylcholinesterase (AChE and antibacterial activities. Adventitious roots derived from 2.5 µM indole-3-acetic acid (IAA treatments and ex vitro-grown plants derived from meta-topolin riboside (mTR and IAA treatments gave the best AChE and antibacterial activities. The in vitro-established M. whitei and ex vitro biomass have comparable ability to function as inhibitors of acetylcholinesterase and antibacterial agents, and can be used as potent bioresources in traditional medicine

Biosorption of U(VI) by the green algae Chlorella vulgaris in dependence of pH value and cell activity

Energy Technology Data Exchange (ETDEWEB)

Vogel, M., E-mail: M.Vogel@fzd.de; Guenther, A.; Rossberg, A.; Li, B.; Bernhard, G.; Raff, J.

2010-12-15

Biosorption of uranium(VI) by the green alga Chlorella vulgaris was studied at varying uranium concentrations from 5 {mu}M to 1 mM, and in the environmentally relevant pH range of 4.4 to 7.0. Living cells bind in a 0.1 mM uranium solution at pH 4.4 within 5 min 14.3 {+-} 5.5 mg U/g dry biomass and dead cells 28.3 {+-} 0.6 mg U/g dry biomass which corresponds to 45% and 90% of total uranium in solution, respectively. During 96 h of incubation with uranium initially living cells died off and with 26.6 {+-} 2.1 mg U/g dry biomass bound similar amounts of uranium compared to dead cells, binding 27.0 {+-} 0.7 mg U/g dry biomass. In both cases, these amounts correspond to around 85% of the initially applied uranium. Interestingly, at a lower and more environmentally relevant uranium concentration of 5 {mu}M, living cells firstly bind with 1.3 {+-} 0.2 mg U/g dry biomass to 1.4 {+-} 0.1 mg U/g dry biomass almost all uranium within the first 5 min of incubation. But then algal cells again mobilize up to 80% of the bound uranium during ongoing incubation in the time from 48 h to 96 h. The release of metabolism related substances is suggested to cause this mobilization of uranium. As potential leachates for algal-bound uranium oxalate, citrate and ATP were tested and found to be able to mobilize more than 50% of the algal-bound uranium within 24 h. Differences in complexation of uranium by active and inactive algae cells were investigated with a combination of time-resolved laser-induced fluorescence spectroscopy (TRLFS), extended X-ray absorption fine structure (EXAFS) spectroscopy and attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Obtained results demonstrated an involvement of carboxylic and organic/inorganic phosphate groups in the uranium complexation with varying contributions dependent on cell status, uranium concentration and pH.

Biosorption of U(VI) by the green algae Chlorella vulgaris in dependence of pH value and cell activity

International Nuclear Information System (INIS)

Vogel, M.; Guenther, A.; Rossberg, A.; Li, B.; Bernhard, G.; Raff, J.

2010-01-01

Biosorption of uranium(VI) by the green alga Chlorella vulgaris was studied at varying uranium concentrations from 5 μM to 1 mM, and in the environmentally relevant pH range of 4.4 to 7.0. Living cells bind in a 0.1 mM uranium solution at pH 4.4 within 5 min 14.3 ± 5.5 mg U/g dry biomass and dead cells 28.3 ± 0.6 mg U/g dry biomass which corresponds to 45% and 90% of total uranium in solution, respectively. During 96 h of incubation with uranium initially living cells died off and with 26.6 ± 2.1 mg U/g dry biomass bound similar amounts of uranium compared to dead cells, binding 27.0 ± 0.7 mg U/g dry biomass. In both cases, these amounts correspond to around 85% of the initially applied uranium. Interestingly, at a lower and more environmentally relevant uranium concentration of 5 μM, living cells firstly bind with 1.3 ± 0.2 mg U/g dry biomass to 1.4 ± 0.1 mg U/g dry biomass almost all uranium within the first 5 min of incubation. But then algal cells again mobilize up to 80% of the bound uranium during ongoing incubation in the time from 48 h to 96 h. The release of metabolism related substances is suggested to cause this mobilization of uranium. As potential leachates for algal-bound uranium oxalate, citrate and ATP were tested and found to be able to mobilize more than 50% of the algal-bound uranium within 24 h. Differences in complexation of uranium by active and inactive algae cells were investigated with a combination of time-resolved laser-induced fluorescence spectroscopy (TRLFS), extended X-ray absorption fine structure (EXAFS) spectroscopy and attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Obtained results demonstrated an involvement of carboxylic and organic/inorganic phosphate groups in the uranium complexation with varying contributions dependent on cell status, uranium concentration and pH.

Natural gas adsorption on biomass derived activated carbons: A mini review

Directory of Open Access Journals (Sweden)

Hamza Usman D.

2016-01-01

Full Text Available Activated carbon materials are good candidates for natural gas storage due excellent textural properties that are easy to enhance and modify. Natural gas is much cleaner fuel than coal and other petroleum derivatives. Storage of natural gas on porous sorbents at lower pressure is safer and cheaper compared to compressed and liquefied natural gas. This article reviews some works conducted on natural gas storage on biomass based activated carbon materials. Methane storage capacities and deliveries of the various sorbents were given. The effect of factors such as surface area, pore characteristic, heat of adsorption, packing density on the natural gas storage capacity on the activated carbons are discussed. Challenges, improvements and future directions of natural gas storage on porous carbonaceous materials are highlighted.

Extended light exposure increases stem digestibility and biomass production of switchgrass

Science.gov (United States)

Zhao, Chunqiao; Hou, Xincun; Zhu, Yi; Yue, Yuesen; Wu, Juying

2017-01-01

Switchgrass is a photoperiod-sensitive energy grass suitable for growing in the marginal lands of China. We explored the effects of extended photoperiods of low-irradiance light (7 μmol·m-2·s-1, no effective photosynthesis) on the growth, the biomass dry weight, the biomass allocation, and, especially, the stem digestibility and cell wall characteristics of switchgrass. Two extended photoperiods (i.e., 18 and 24 h) were applied over Alamo. Extended light exposure (18 and 24 h) resulted in delayed heading and higher dry weights of vegetative organs (by 32.87 and 35.94%, respectively) at the expense of reducing the amount of sexual organs (by 40.05 and 50.87%, respectively). Compared to the control group (i.e., natural photoperiod), the yield of hexoses (% dry matter) in the stems after a direct enzymatic hydrolysis (DEH) treatment significantly increased (by 44.02 and 46.10%) for those groups irradiated during 18 and 24 h, respectively. Moreover, the yield of hexoses obtained via enzymatic hydrolysis increased after both basic (1% NaOH) and acid (1% H2SO4) pretreatments for the groups irradiated during 18 and 24 h. Additionally, low-irradiance light extension (LILE) significantly increased the content of non-structural carbohydrates (NSCs) while notably reducing the lignin content and the syringyl to guaiacyl (S/G) ratio. These structural changes were in part responsible for the observed improved stem digestibility. Remarkably, LILE significantly decreased the cellulose crystallinity index (CrI) of switchgrass by significantly increasing both the arabinose substitution degree in xylan and the content of ammonium oxalate-extractable uronic acids, both favoring cellulose digestibility. Despite this LILE technology is not applied to the cultivation of switchgrass on a large scale yet, we believe that the present work is important in that it reveals important relationships between extended day length irradiations and biomass production and quality. Additionally, this

Effect of drying methods with the application of vacuum microwaves on the bioactive compounds, color, and antioxidant activity of strawberry fruits.

Science.gov (United States)

Wojdyło, Aneta; Figiel, Adam; Oszmiański, Jan

2009-02-25

The objective of this study was to evaluate the application of vacuum-microwave drying (240, 360, and 480 W) in the production process of dehydrated strawberry and to compare and contrast the quality of these dehydrated strawberries in terms of their polyphenol compounds, concentration of some heat liable components, and color to that of freeze-dried, convective, and vacuum-dried strawberry. Thus, the effect of vacuum-microwave drying and other drying methods on the antioxidant activity of berries was evaluated. Whole fresh and dried fruits were assessed for phenolics (anthocyanins, flavanols, hydroxycinnamic acids, and flavonols), ascorbic acid, and antioxidant activity (all parameters were calculated on a dry matter basis). Analysis of data shows that ellagic acid and flavanol changes were affected by drying techniques and cultivar. Drying destroyed anthocyanins, flavanols, and ascorbic acid, and there was a significant decrease in antioxidant activity. The most striking result was that conventional and vacuum drying decreased antioxidant activity in both cultivars, whereas contradictory results were found for vacuum-microwave processed strawberry. This study has demonstrated that vacuum-microwave drying, especially at 240 W, can produce high-quality products, with the additional advantage of reduced processing times, compared to other processes such as freeze-drying.

System applications CRC -Biomass + Coal; Aplicaciones Sistema CRC-Biomasa+Carbon

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

Main object of Phase I of the project is to analyse the technical-economic feasibility of the combined use of biomass and coal for power generation in the Spanish region of Andalusia, by means of new medium-size independent power plants or using biomass as supplementary fuel in existing large coal power plants, including: -Analysis and classification of biomass and coal resources in the region -Technical-economic study of conventional alternatives using the steam cycle -Analysis of efficiency improvement provided by advanced Rankine-cycle technologies, like the SMR cycle -Analysis of alternatives based on parallel combined cycles using gas turbines, including advanced solutions, like the EAPI and CRC-EAPI systems. -Description and evaluation of different biomass drying systems. -Description and evaluation of the three main biomass gasification systems currently under development: atmospheric direct, atmospheric indirect and pressurized. Main objects of Phase II of the project are to analyse a specific application of the EAPI system to a real cogeneration plant project and to analyse the application of the CRC2 system to a commercial supercritical power plant, including technical-economic study of both applications. (Author)

Effects of cladode age on biomass yield and nutritional value of ...

African Journals Online (AJOL)

A randomized complete block design with five replications was used to assess biomass yield, in vitro dry matter digestibility (IVDMD) and nutritional value of spineless cactus (Opuntia ficus-indica) produced under drip irrigation and fertilization. Cladodes were harvested from an established plantation at 30, 37, 45, 60, ...

Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

Energy Technology Data Exchange (ETDEWEB)

Renella, Giancarlo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)], E-mail: giancarlo.renella@unifi.it; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)

2008-04-15

We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness.

Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

International Nuclear Information System (INIS)

Renella, Giancarlo; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo

2008-01-01

We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness

Comparative Study of Antibacterial Activities of the Fresh and Dried ...

African Journals Online (AJOL)

The fresh and dried fruit extracts of Capsicum species were screened for antibacterial activities against Staph. aureus, S. typhi and B. subtilis using two assay methods. The filter disk and agar plate diffusion were the assay methods employed in the study. The results of the study revealed that the extracts obtained from the ...

Valorization of Sargassum muticum Biomass According to the Biorefinery Concept

Directory of Open Access Journals (Sweden)

Elena M. Balboa

2015-06-01

Full Text Available The biorefinery concept integrates processes and technologies for an efficient biomass conversion using all components of a feedstock. Sargassum muticum is an invasive brown algae which could be regarded as a renewable resource susceptible of individual valorization of the constituent fractions into high added-value compounds. Microwave drying technology can be proposed before conventional ethanol extraction of algal biomass, and supercritical fluid extraction with CO2 was useful to extract fucoxanthin and for the fractionation of crude ethanol extracts. Hydrothermal processing is proposed to fractionate the algal biomass and to solubilize the fucoidan and phlorotannin fractions. Membrane technology was proposed to concentrate these fractions and obtain salt- and arsenic-free saccharidic fractions. Based on these technologies, this study presents a multipurpose process to obtain six different products with potential applications for nutraceutical, cosmetic and pharmaceutical industries.

EnviroAtlas - Below Ground Live Tree Biomass Carbon Storage for the Conterminous United States- Forested

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset includes the average below ground live tree root dry biomass estimate for the Watershed Boundary Dataset (WBD) 12-digit Hydrologic Unit...

Fungi and their biomass in detritus of the seagrass Thalassia hemprichii (Ehrenberg) Ascherson

Digital Repository Service at National Institute of Oceanography (India)

Sathe, V.; Raghukumar, S.

Kalpeni Island revealed different kinds of hyphae and unicellular thraustochytrid fungi, particularly in later stages of decomposition. Highest values of biomass estimatEd. by direct observations were 31840 x 10-6 g mycelial fungi per g dry wt. detritus...

Functional diversity of carbohydrate-active enzymes enabling a bacterium to ferment plant biomass.

Science.gov (United States)

Boutard, Magali; Cerisy, Tristan; Nogue, Pierre-Yves; Alberti, Adriana; Weissenbach, Jean; Salanoubat, Marcel; Tolonen, Andrew C

2014-11-01

Microbial metabolism of plant polysaccharides is an important part of environmental carbon cycling, human nutrition, and industrial processes based on cellulosic bioconversion. Here we demonstrate a broadly applicable method to analyze how microbes catabolize plant polysaccharides that integrates carbohydrate-active enzyme (CAZyme) assays, RNA sequencing (RNA-seq), and anaerobic growth screening. We apply this method to study how the bacterium Clostridium phytofermentans ferments plant biomass components including glucans, mannans, xylans, galactans, pectins, and arabinans. These polysaccharides are fermented with variable efficiencies, and diauxies prioritize metabolism of preferred substrates. Strand-specific RNA-seq reveals how this bacterium responds to polysaccharides by up-regulating specific groups of CAZymes, transporters, and enzymes to metabolize the constituent sugars. Fifty-six up-regulated CAZymes were purified, and their activities show most polysaccharides are degraded by multiple enzymes, often from the same family, but with divergent rates, specificities, and cellular localizations. CAZymes were then tested in combination to identify synergies between enzymes acting on the same substrate with different catalytic mechanisms. We discuss how these results advance our understanding of how microbes degrade and metabolize plant biomass.

Global patterns of socioeconomic biomass flows in the year 2000. A comprehensive assessment of supply, consumption and constraints

International Nuclear Information System (INIS)

Krausmann, Fridolin; Erb, Karl-Heinz; Gingrich, Simone; Lauk, Christian; Haberl, Helmut

2008-01-01

Human use of biomass has become a major component of the global biogeochemical cycles of carbon and nitrogen. The use of land for biomass production (e.g. cropland) is among the most important pressures on biodiversity. At the same time, biomass is indispensable for humans as food, animal feed, raw material and energy source. In order to support research into these complex issues, we here present a comprehensive assessment of global socioeconomic biomass harvest, use and trade for the year 2000. We developed country-level livestock balances and a consistent set of factors to estimate flows of used biomass not covered by international statistics (e.g. grazed biomass, crop residues) and indirect flows (i.e. biomass destroyed during harvest but not used). We found that current global terrestrial biomass appropriation amounted to 18.7 billion tonnes dry matter per year (Pg/yr) or 16% of global terrestrial NPP of which 6.6 Pg/yr were indirect flows. Only 12% of the economically used plant biomass (12.1 Pg/yr) directly served as human food, while 58% were used as feed for livestock, 20% as raw material and 10% as fuelwood. There are considerable regional variations in biomass supply and use. Distinguishing 11 world regions, we found that extraction of used biomass ranged from 0.3 to 2.8 t/ha/yr, per-capita values varied between 1.2 and 11.7 t/cap/yr (dry matter). Aggregate global biomass trade amounted to 7.5% of all extracted biomass. An analysis of these regional patterns revealed that the level of biomass use per capita is determined by historically evolved patterns of land use and population density rather than by affluence or economic development status. Regions with low population density have the highest level of per-capita biomass use, high-density regions the lowest. Livestock, consuming 30-75% of all harvested biomass, is another important factor explaining regional variations in biomass use. Global biomass demand is expected to grow during the next decades

Energy Requirements for Biomass Harvest and Densification

Directory of Open Access Journals (Sweden)

Kevin Shinners

2018-03-01

Full Text Available This research quantified the unit and bulk density of several biomass crops across a variety of harvest and processing methods, as well as the energy and fuel requirements for these operations. A load density of approximately 240 kg·m−3 is needed to reach the legal weight limit of most transporters. Of the three types of balers studied, only the high density (HD large square baler achieved this target density. However, the specific energy and fuel requirements increased exponentially with bale density, and at the maximum densities for corn stover and switchgrass, the dry basis energy and fuel requirements ranged from 4.0 to 5.0 kW·h·Mg−1 and 1.2 to 1.4 L·Mg−1, respectively. Throughputs of tub grinders when grinding bales was less than any other harvesting or processing methods investigated, so specific energy and fuel requirements were high and ranged from 13 to 32 kW·h·Mg−1 and 5.0 to 11.3 L·Mg−1, respectively. Gross size-reduction by pre-cutting at baling increased bale density by less than 6% and increased baling energy requirements by 11% to 22%, but pre-cut bales increased the tub grinder throughput by 25% to 45% and reduced specific fuel consumption for grinding by 20% to 53%. Given the improvement in tub grinder operation, pre-cutting bales should be considered as a means to increase grinder throughput. Additional research is needed to determine the energy required to grind high density pre-cut bales at high throughputs so that better estimates of total energy required for a high density bale system can be made. An alternative bulk feedstock system was investigated that involved chopping moist biomass crops with a precision-cut forage harvester, compacting the bulk material in a silo bag, and then segmenting the densified material into modules optimized for efficient transport. The specific fuel use for chopping and then compacting biomass crops in the silo bag ranged from 1.6 to 3.0 L·Mg−1 and 0.5 to 1.3 L·Mg−1

Resource Limitations on Soil Microbial Activity in an Antarctic Dry Valley

DEFF Research Database (Denmark)

Sparrow, Asley; Gregorich, Ed; Hopkins, David

2011-01-01

Although Antarctic dry valley soils function under some of the harshest environmental conditions on the planet, there is significant biological activity concentrated in small areas in the landscape. These productive areas serve as a source of C and N in organic matter redistributed...... to the surrounding biologically impoverished soils. We conducted a 3-yr replicated field experiment involving soil amendment with C and N in simple (glucose and NH4Cl) and complex (glycine and lacustrine detritus) forms to evaluate the resource limitations on soil microbial activity in an Antarctic dry valley....... The respiratory response for all substrates was slow, with a significant but weak response to NH4Cl, followed by a more widespread response to all substrates after 2 yr and in laboratory incubations conducted 3 yr after substrate addition. This response suggests that the soil microbial community is N limited and...

Biomass: towards more co-generation than gasification? Interview with Jean-Christophe Pouet; Figures for the heat fund; biomass in the Parisian heat network; gasification still at the promise stage; Engie bets on bio-methane of 2. generation; a new bidding for biomass co-generation

International Nuclear Information System (INIS)

Petitot, Pauline; De Santis, Audrey; Mary, Olivier; Signoret, Stephane

2016-01-01

After some brief presentations of some highlights in the biomass sector in France, Ukraine, UK and Brazil, a set of articles proposes an overview of recent developments and perspectives for the biomass-based energy and heat production in France. It presents and comments some emerging projects based on biomass gasification as technologies have evolved for a higher economic profitability. It discusses the action of the Heat Fund (Fonds chaleur) which supports investors in a context constrained by the hard competition with fossil energies, notably with gas as discussed in an interview with a member of the ADEME. Some tables and graphs give data about biomass installations supported by the Heat fund, about subsidies awarded by the ADEME, about the production of the various heat sources. An article comments the operation of a biomass-based plant near Paris which supplies the Parisian heat network. A project of methane production from dry biomass from local resources by Engie near Lyons (methane of second generation). The last article comments a new bidding process for co-generation projects which can be an opportunity for new projects, and not only big ones

Measured and modeled humidification factors of fresh smoke particles from biomass burning: role of inorganic constituents

Directory of Open Access Journals (Sweden)

J. L. Hand

2010-07-01

Full Text Available During the 2006 FLAME study (Fire Laboratory at Missoula Experiment, laboratory burns of biomass fuels were performed to investigate the physico-chemical, optical, and hygroscopic properties of fresh biomass smoke. As part of the experiment, two nephelometers simultaneously measured dry and humidified light scattering coefficients (b_sp(dry and b_sp(RH, respectively in order to explore the role of relative humidity (RH on the optical properties of biomass smoke aerosols. Results from burns of several biomass fuels from the west and southeast United States showed large variability in the humidification factor (f(RH=b_sp(RH/b_sp(dry. Values of f(RH at RH=80–85% ranged from 0.99 to 1.81 depending on fuel type. We incorporated measured chemical composition and size distribution data to model the smoke hygroscopic growth to investigate the role of inorganic compounds on water uptake for these aerosols. By assuming only inorganic constituents were hygroscopic, we were able to model the water uptake within experimental uncertainty, suggesting that inorganic species were responsible for most of the hygroscopic growth. In addition, humidification factors at 80–85% RH increased for smoke with increasing inorganic salt to carbon ratios. Particle morphology as observed from scanning electron microscopy revealed that samples of hygroscopic particles contained soot chains either internally or externally mixed with inorganic potassium salts, while samples of weak to non-hygroscopic particles were dominated by soot and organic constituents. This study provides further understanding of the compounds responsible for water uptake by young biomass smoke, and is important for accurately assessing the role of smoke in climate change studies and visibility regulatory efforts.

Response of rice genotypes to weed competition in dry direct-seeded rice in India.

Science.gov (United States)

Mahajan, Gulshan; Ramesha, Mugalodi S; Chauhan, Bhagirath S

2014-01-01

The differential weed-competitive abilities of eight rice genotypes and the traits that may confer such attributes were investigated under partial weedy and weed-free conditions in naturally occurring weed flora in dry direct-seeded rice during the rainy seasons of 2011 and 2012 at Ludhiana, Punjab, India. The results showed genotypic differences in competitiveness against weeds. In weed-free plots, grain yield varied from 6.6 to 8.9 t ha(-1) across different genotypes; it was lowest for PR-115 and highest for the hybrid H-97158. In partial weedy plots, grain yield and weed biomass at flowering varied from 3.6 to 6.7 t ha(-1) and from 174 to 419 g m(-2), respectively. In partial weedy plots, grain yield was lowest for PR-115 and highest for PR-120. Average yield loss due to weed competition ranged from 21 to 46% in different rice genotypes. The study showed that early canopy closure, high leaf area index at early stage, and high root biomass and volume correlated positively with competitiveness. This study suggests that some traits (root biomass, leaf area index, and shoot biomass at the early stage) could play an important role in conferring weed competitiveness and these traits can be explored for dry-seeded rice.

Modeling of the pyrolysis of biomass under parabolic and exponential temperature increases using the Distributed Activation Energy Model

International Nuclear Information System (INIS)