WorldWideScience

Sample records for dowtherm

  1. Evaluation of diphenyl and dowtherm-A's thermal cross sections and their application to reactor calculation

    International Nuclear Information System (INIS)

    Florido, P.C.; Gillette, V.H.; Granada, J.R.; Patino, N.E.

    1990-01-01

    This work applies a scattering synthetic approximation to represent diphenyl and dowtherm-A dispersion laws on typical ranges of interest regarding temperature. The present formalism is based on a previous model of benzene molecule formerly validated. The results obtained from diphenyl agree with laboratory measurements, but those regarding dowtherm-A present some variations with respect to the available information. The result of the application of this model to the measurements made in Wrenlingen (Switzerland) to measure the vacuum coefficient of the cells charasteristic of high conversion reactors, are also presented, experimentally simulating said vacuum using dowtherm-A instead of H 2 O. (Author) [es

  2. Measurement of the specific heats of Santowax 'R', para-, meta- and ortho-terphenyl, diphenyl and dowtherm 'A'

    International Nuclear Information System (INIS)

    Bowring, R.W.; Garton, D.A.; Norris, H.F.

    1960-12-01

    New absolute measurements have been made of the specific heats of Santowax 'R1, the terphenyl isomers, diphenyl and Dowtherm 'A'. An adiabatic calorimeter was used in which the sample was heated electrically while a surrounding jacket was maintained at the same temperature as the calorimeter. The specific heats of all materials tested were found to increase linearly with temperature, the slope being substantially the same for all the pure materials except para-terphenyl. The specific heat of Santowax 'R' was about 1/2% less than the weighted mean of its components. The probable accuracy of the measurements was ± 2% and this was confirmed by comparison with diphenyl ether. A summary of results is given in Table 1 and Figure 10. (author)

  3. Design of the Natural Circulation Loop and Implementation of DOWTHERM A Properties into MARS-LMR Code

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Yukyung; Park, Seong Dae; Kang, Sarah; Bang, In Cheol [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

    2015-05-15

    Molten Salt Reactor (MSR), which is one of the generation IV reactors, has an advantage in these requirements. MSR uses a molten salt mixture as the primary coolant, or the fuel itself and it operates on high temperature, so it doesn't need pressurizing. Also, liquid state fuel has an advantage for pyro-processing with easy separation of fission products. These fission products also have relatively short half-lives compared to those of the existing reactors. With these characteristics, MSR can have inherent safety in both direct and indirect sides. Also, MSR can operate at high temperature range, so that it can have the high efficiency to produce electricity. Therefore, research of MSR is meaningful for developing advanced nuclear reactors. FLiBe which is a mixture of lithium fluoride (LiF) and beryllium fluoride (BeF{sub 2}) is used as a primary coolant in MSR and LMR (Liquid Metal cooled Reactor). It has superiority over conventional liquid metal coolant like sodium, because it doesn't react with air or water. thermos-physical properties of DOWTHERM A for MARS-LMR code were made by modifying stg file of existing one. It was based on the process of Moore using 6 output parameters such as specific volume, internal energy, thermal expansion coefficient, isothermal compressibility, specific heat and entropy. With generated stg file (stgdowa.f90) and input file, tpf file (tpfdowa) which includes fluid property tables for MARS-LMR simulation was obtained. For the verification, this tpf file with execution file will be applied to the input deck of our natural circulation design. This work will contribute to researching and developing of MSR and LMR.

  4. Measurement of the surface tension of Santowax 'R', para-, meta-, and ortho-terphenyl, diphenyl, diphenyl ether and dowtherm 'A'

    International Nuclear Information System (INIS)

    Bowring, R.W.; Garton, D.A.; Kinneir, J.H.

    1961-09-01

    Values of surface tension were obtained over the temperature range from near the melting point to near the normal boiling point of each substance. A capillary rise method was used employing a closed glass U-tube apparatus. The accuracy was ± 3% near the melting point falling to ± 5% near the normal boiling point. Values of the parachor calculated from the experimental data were in excellent agreement with those calculated from the molecular structure using the method proposed by Sugden. The surface tension in each case decreased with ascending temperature from near 30 to 40 dynes/cm close to the melting point to 13 to 15 dynes/cm near the normal boiling point. (author)

  5. Evaluation of organic coolants for the transportation of LMFBR spent fuel rods

    International Nuclear Information System (INIS)

    Arnold, C. Jr.

    1978-05-01

    The physical and chemical processes that are likely to occur when sodium coated LMFBR spent fuel rods are submerged in various aromatic organic coolants was defined by means of immersion experiments carried out with sodium coated 304 stainless steel coupons. Upon immersion of sodium coated coupons at 220 0 C in hydrocarbon type coolants such as Therminol 88, a mixture of terphenyls, not only was the metallic sodium retained on the coupon, but a carbonaceous coating formed on the surface of the sodium. In contrast, coolants that contained aromatic ether bonds, such as Dowtherm A, reacted with sodium at 220 0 C to form phenolate and other salts, which precipitated from the coolant in the form of a dark sludge. With Dowtherm A, removal of metallic sodium from the coupon was essentially complete in a matter of hours at temperatures of 160--220 0 C. Data on the rate and efficiency of sodium removal upon immersion in Dowtherm A at elevated temperatures were obtained. In addition the kinetics and chemistry of the sodium/Dowtherm A reaction were defined. Because sodium sludges are potentially incompatible with the containing structural materials and the fuel elements, it is recommended that sodium be removed prior to immersion in the coolant via reaction with benzoic acid; this method should be adaptable to the facilities at reactor sites. In aging studies Dowtherm A was found to be thermally stable up to 400 0 C and radiatively stable at ambient conditions. The combined effect of heat and radiation was not defined

  6. Preliminary Study of Single-Phase Natural Circulation for Lab-scaled Molten Salt Application

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Yukyung; Kang, Sarah; Kim, In Guk; Seo, Seok Bin; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of); Park, Seong Dae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Advanced reactors such as MSR (FHR), VHTR and AHTR utilized molten salt as a coolant for efficiency and safety which has advantages in higher heat capacity, lower pumping power and scale compared to liquid metal. It becomes more necessary to study on the characteristics of molten salt. However, due to several characteristics such as high operating temperature, large-scale facility and preventing solidification, satisfying that condition for study has difficulties. Thus simulant fluid was used with scaling method for lab-scale experiment. Scaled experiment enables simulant fluid to simulate fluid mechanics and heat transfer behavior of molten salt on lower operating temperature and reduced scale. In this paper, as a proof test of the scaled experiment, simplified single-phase natural circulation loop was designed in a lab-scale and applied to the passive safety system in advanced reactor in which molten salt is considered as a major coolant of the system. For the application of the improved safety system, prototype was based on the primary loop of the test-scale DRACS, the main passive safety system in FHR, developed at the OSU. For preliminary experiment, single-phase natural circulation under low power was performed. DOWTHERM A and DOWTHERM RP were selected as simulant candidates. Then, study of feasibility with simulant was conducted based on the scaling law for heat transfer characteristics and geometric parameters. Additionally, simulation with MARS code and ANSYS-CFX with the same condition of natural circulation was carried out as verification. For the accurate code simulation, thermo-physical properties of DOWTHERM A and RP were developed and implemented into MARS code. In this study, single-phase natural circulation experiment was performed with simulant oil, DOWTHERM RP, based on the passive safety system of FHR. Feasibility of similarity experiment for molten salt with oil simulant was confirmed by scaling method. In addition, simulation with two

  7. Role and status of scaled experiments in the development of fluoride-salt-cooled, high-temperature reactors - 15185

    International Nuclear Information System (INIS)

    Zweibaum, N.; Huddar, L.; Laufer, M.R.; Peterson, P.F.; Hughes, J.T.; Blandford, E.D.; Scarlat, R.O.

    2015-01-01

    Development of fluoride-salt-cooled, high-temperature reactor (FHR) technology requires a better understanding of key hydrodynamic and heat transfer phenomena associated with this novel class of reactors. The use of simulant fluids that can match the most important non dimensional numbers between scaled experiments and prototypical FHR systems enables integral effects tests (IETs) to be performed at reduced cost and difficulty for FHR code validation. The University of California at Berkeley (UCB) and the University of New Mexico (UNM) have built a number of IETs and separate effects tests to investigate pebble-bed FHR (PB-FHR) phenomenology using water or simulant oils such as Dowtherm A. PB-FHR pebble motion and porous media flow dynamics have been investigated with UCB's pebble recirculation experiments using water and plastic spheres. Transient flow of high-Prandtl-number fluids around hot spheres has also been investigated by UCB to measure Nusselt numbers in pebble-bed cores, using simulant oils and copper spheres. Finally, single-phase forced/natural circulation has been investigated using the scaled height, reduced flow area loops of the Compact Integral Effects Test facility at UCB and a multi-flow regime loop at UNM, using Dowtherm A oil. The scaling methodology and status of these ongoing experiments are described here

  8. Problems of heat transfer within the containing vessel of high performance LMFBR spent fuel shipping casks

    International Nuclear Information System (INIS)

    Pope, R.B.; Gartling, D.K.; Schimmel, W.P. Jr.; Larson, D.W.

    1976-01-01

    A preliminary assessment of heat transfer problems internal to a LMFBR spent fuel shipping cask is reported. The assessment is based upon previous results obtained in full-scale, electrically heated mockups of an LMFBR assembly located in a containing pipe, and also upon analytical and empirical studies presented in this paper. It is shown that a liquid coolant will be required to adequately distribute the decay heat of short-cooled assemblies from the fuel region to the containing cask structure. Liquid sodium apparently provides the best heat transfer, and sufficient data are available to adequately model the heat transfer processes involved. Dowtherm A is the most efficient organic evaluated to date and presented in the open literature. Since the organic materials have high Prandtl and usually high Rayleigh numbers, natural convection is the predominant mode of heat transfer. It is shown that a more comprehensive understanding of the convective processes will be required before heat transfer with an organic coolant can be adequately modeled. However, in view of systems considerations, Dowtherm A should be further considered as an alternative to sodium for use as a LMFBR spent fuel shipping cask coolant

  9. Effects of fuel enrichment on the physics characteristics of plutonium-fueled light water high converter reactors

    International Nuclear Information System (INIS)

    Chawla, R.; Seiler, R.; Gmur, K.

    1986-01-01

    Investigations have been carried out for three additional cores of the phase 1 experimental program on light water high converter reactor test lattices in the PROTEUS facility. An 8% (average) fissile plutonium tight-pitch lattice with a fuel/moderator volumetric ratio of 2.0 was considered. As for the earlier reported 6% (average) fissile plutonium test lattice, H 2 O, Dowtherm, and air were the moderator state investigated. Significant enrichment-dependent trends have been identified in the comparisons of calculated and experimental results for the wet (moderated cases, particularly for the important reaction rate ratio of 238 U capture of 239 Pu fission. These are then reflected in the comparison of moderator voidage characteristics, expressed in terms of individual components of the kinfinity void coefficient

  10. Reactor loops at Chalk River

    International Nuclear Information System (INIS)

    Sochaski, R.O.

    1962-07-01

    This report describes broadly the nine in-reactor loops, and their components, located in and around the NRX and NRU reactors at Chalk River. First an introduction and general description is given of the loops and their function, supplemented with a table outlining some loop specifications and nine simplified flow sheets, one for each individual loop. The report then proceeds to classify each loop into two categories, the 'main loop circuit' and the 'auxiliary circuit', and descriptions are given of each circuit's components in turn. These components, in part, are comprised of the main loop pumps, the test section, loop heaters, loop coolers, delayed-neutron monitors, surge tank, Dowtherm coolers, loop piping. Here again photographs, drawings and tables are included to provide a clearer understanding of the descriptive literature and to include, in tables, some specifications of the more important components in each loop. (author)

  11. Contamination Assessment Report Chemical Sewers - North Plants and South Plants Version 3.2, Task 10

    Science.gov (United States)

    1988-09-01

    concrete supports. Tanks stored fuel oil for incinerators and boilers . In addition, Buildings 1404, 1405, 1502, 1507, and 1508 are part of Tank Farm 1403...ethylparathion and azodrin 1951-1981 514A Dowtherm Building, lewisite (M-1) crude storage, army boiler , burned in 1951, rebuilt 514C Acid pumping station 514E...w (P- f I- 0 tcI 0 ý6888 888 HHO 88888§1 0808 088 (l uU(UI QUUQU QUOm4U u4uuuu u u U(JUUU U UU U)(J a D oes 0~5 0S @ aO O a Do e a0aMa Dome * a o l

  12. Status of the Tidal Regenerator Engine for nuclear circulatory support systems

    International Nuclear Information System (INIS)

    Watelet, R.P.; Ruggles, A.E.; Torti, V.

    1976-01-01

    Based on the annular version of the Tidal Regenerator Engine, a packaged energy system for nuclear powered circulatory support systems was developed. Net power output of approximately 3 watts is delivered using a 33-watt heat source for an engine module volume of 0.7 liter and a weight of 1.6 kg. A higher efficiency dual cycle version of the annular engine using a Dowtherm A topping cycle on the basic steam cycle is also under development. Projected system output using this advanced engine is 5 watts for the same sized heat source. Life testing of critical components has demonstrated substantial reliability improvement over earlier designs. Of particular significance is the continuing operation of a complete implantable engine system after 1200 hours. Component life testing is continuing with over five thousand hours accumulated on two pump actuators employing welded metal bellows

  13. Effects of fuel enrichment on the physics characteristics of plutonium-fueled light water high converter reactors

    International Nuclear Information System (INIS)

    Chawla, R.; Seiler, R.; Gmuer, K.

    1986-01-01

    Investigations have been carried out for three additional cores of the phase 1 experimental program on light water high converter reactor test lattices in the PROTEUS facility. An 8% (average) fissile plutonium tight-pitch lattice with a fuel/moderator volumetric ratio of 2.0 was considered. As for the earlier reported 6% (average) fissile plutonium test lattice, H 2 O, Dowtherm, and air were the moderator states investigated. Significant enrichment-dependent trends have been identified in the comparisons of calculated and experimental results for the wet (moderated) cases, particularly for the important reaction rate ratio of 238 U capture to 239 Pu fission. These are then reflected in the comparison of moderator voidage characteristics, expressed in terms of individual components of the k-infinity void coefficient. (author)

  14. Equipment for RAW handling, packaging, transport and storage from ZTS VVU KOSICE a.s

    International Nuclear Information System (INIS)

    Vargovcik, L.

    2004-01-01

    Since 1988, the company ZTS VVU KOSICE has devoted a great part of its activities to the development of equipment for RAW handling, packaging, transport and storage, mainly for application in the decommissioning of NPP A1 at Jaslovske Bohunice in Slovakia. This is a HWGCR NPP shut down following a breakdown in 1977. This incident was caused by disruption of the technological channel serving as a barrier between heavy water moderator and fuel assembly. Damage of this barrier enabled heavy water leakage into the primary circuit with partial fuel elements cladding damage and subsequent additional contamination of the primary circuit. During two consecutive years after the incident main effort was focused on activities related to personnel and environment protection, moderator draining, reactor defuelling, dry cleaning of the primary circuit, repair and maintenance of equipment. The next step was the preparation of the concept of NPP A-1 introduction into dry safe state. The order of importance of RAW liquidation was as follows: 1. Spent fuel - spent fuel assemblies from NPP A-1 were, after short cooling, stored temporarily in storage pipe containers filled at the beginning of NPP operation with ''chrompik'' (an aqueous solution of K 2 Cr 2 O 7 with concentration of 3-5%), later with ''dowtherm'' (mixture of bi-phenyl oxide and bi-phenyl). The containers were placed in a storage pond filled with water. 2. Liquid RAW - combustible (dowtherm, oils) and non-combustible (chrompik, Demi water, decontaminating solutions, sludge, sorbents, etc.) 3. Solid RAW - metallic and non-metallic For this purpose, it was necessary to build RAW processing lines, intermediate storage facilities and systems for manipulation and transport of RAW

  15. Gas-cooled fast-breeder reactor. Helium Circulator Test Facility updated design cost estimate

    International Nuclear Information System (INIS)

    1979-04-01

    Costs which are included in the cost estimate are: Titles I, II, and III Architect-Engineering Services; Titles I, II, and III General Atomic Services; site clearing, grading, and excavation; bulk materials and labor of installation; mechanical and electrical equipment with installation; allowance for contractors' overhead, profit, and insurance; escalation on materials and labor; a contingency; and installation of GAC supplied equipment and materials. The total estimated cost of the facility in As Spent Dollars is $27,700,000. Also included is a cost comparison of the updated design and the previous conceptual design. There would be a considerable penalty for the direct-cooled system over the indirect-cooled system due to the excessive cost of the large diameter helium loop piping to an outdoor heat exchanger. The indirect cooled system which utilizes a helium/Dowtherm G heat exchanger and correspondingly smaller and lower pressure piping to its outdoor air cooler proved to be the more economical of the two systems

  16. Reactivity and reaction rate ratio changes with moderator voidage in a light water high converter reactor lattice

    International Nuclear Information System (INIS)

    Chawla, R.; Gmuer, K.; Hager, H.; Seiler, R.

    1986-01-01

    Integral reaction rate ratios and other k ∞ related parameters have been measured in the first three cores of the experimental program on light water high converter reactor (LWHCR) test lattices in the PROTEUS reactor. The reference tight-pitch lattice consisted of two rod types, with an average fissile-plutonium enrichment of 6% and a fuel/moderator ratio of 2.0. The moderators were H 2 O, Dowtherm (simulating an H 2 O voidage of 42.5%), and air (100% void). Comparisons of the measured parameters have been made with calculational results based mainly on the use of two separate codes and their associated data libraries, namely, WIMS-D and EPRI-CPM. A reconstruction of individual components of the k-infinity void coefficient has been carried out on the basis of the measured changes with voidage of the various reaction rate ratios, as well as of k-infinity itself. The subsequent more detailed comparisons between experiment and calculation should provide a useful basis for resolving the conflicting calculational results that have been reported in the past for the void coefficient characteristics of LWHCRs. (author)

  17. Benchmark Simulation of Natural Circulation Cooling System with Salt Working Fluid Using SAM

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, K. K.; Scarlat, R. O.; Hu, R.

    2017-09-03

    Liquid salt-cooled reactors, such as the Fluoride Salt-Cooled High-Temperature Reactor (FHR), offer passive decay heat removal through natural circulation using Direct Reactor Auxiliary Cooling System (DRACS) loops. The behavior of such systems should be well-understood through performance analysis. The advanced system thermal-hydraulics tool System Analysis Module (SAM) from Argonne National Laboratory has been selected for this purpose. The work presented here is part of a larger study in which SAM modeling capabilities are being enhanced for the system analyses of FHR or Molten Salt Reactors (MSR). Liquid salt thermophysical properties have been implemented in SAM, as well as properties of Dowtherm A, which is used as a simulant fluid for scaled experiments, for future code validation studies. Additional physics modules to represent phenomena specific to salt-cooled reactors, such as freezing of coolant, are being implemented in SAM. This study presents a useful first benchmark for the applicability of SAM to liquid salt-cooled reactors: it provides steady-state and transient comparisons for a salt reactor system. A RELAP5-3D model of the Mark-1 Pebble-Bed FHR (Mk1 PB-FHR), and in particular its DRACS loop for emergency heat removal, provides steady state and transient results for flow rates and temperatures in the system that are used here for code-to-code comparison with SAM. The transient studied is a loss of forced circulation with SCRAM event. To the knowledge of the authors, this is the first application of SAM to FHR or any other molten salt reactors. While building these models in SAM, any gaps in the code’s capability to simulate such systems are identified and addressed immediately, or listed as future improvements to the code.

  18. Toward Reanalysis of the Tight-Pitch HCLWR-PROTEUS Phase II Experiments

    Science.gov (United States)

    Perret, Grégory; Vlassopoulos, Efstathios; Hursin, Mathieu; Pautz, Andreas

    2016-03-01

    The HCLWR-Proteus Phase II experiments were conducted from 1985 to 1990 in the zero-power reactor Proteus at PSI in Switzerland. The experimental program was dedicated to the physics of high conversion light water reactors and in particular to the measurement of reactor parameters such as reaction rate traverses, spectral indices, absorber reactivity worths and void coefficients. The HCLWR experiments are especially interesting because they generated knowledge in the epithermal range of the neutron flux spectrum, for which little integral experimental data is available. In an effort to assess the interest of this experimental data to validate modern nuclear data and improve their uncertainties, a preliminary re-analysis of selected configurations was conducted with Monte-Carlo codes (MCNP6/SERPENT2) and modern nuclear data libraries (ENDF/B-VII.0, JEFF-3.1.1 and JENDL-4.0). The spectral ndices, flux spectra and sensitivity coefficients on k∞ were calculated using cell models representative of the tight-pitch measurement configurations containing 11% PuO2-UO2 fuel rods in different moderation conditions (air, water and dowtherm). Spectral index predictions using the three nuclear data libraries agreed within two standard deviations with the measured values. The only exception is the Pu-242-capture-to-Pu-239-fission ratio, which was overestimated with all libraries by more than four standard deviations, i.e. 13%, in the non-moderated configuration. In this configuration, Pu-242 captures are few since the flux spectrum in the Pu-242 capture resonance region (between 1eV and 1keV) is small making this spectral index hard to measure. Sensitivity coefficient predictions with both MCNP6 and SERPENT2 were in good agreement.