Welding, Bonding and Fastening, 1984

Science.gov (United States)

Buckley, J. D. (Editor); Stein, B. A. (Editor)

1985-01-01

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Soceity, and Society of Manufacturing Engineers conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

RFID Torque Sensing Tag System for Fasteners

Science.gov (United States)

Fink, Patrick W. (Inventor); Lin, Gregory Y. (Inventor); Ngo, Phong H. (Inventor); Kennedy, Timothy F. (Inventor)

2016-01-01

The present invention provides an RFID-based torque sensor that can be used to quickly monitor off the shelf fasteners including fasteners that are used in expensive satellites or other uses where fastener failure can be very costly. In one embodiment, an antenna, RFID ring and spring comprise a sensor tag that can be interrogated with an interrogation signal produced by an interrogator device. When sufficient torque is applied to the fastener, an RFID circuit is connected, and produces a radio frequency (RF) signal that can be read by the interrogator. In one embodiment, the RFID circuit does not transmit when the spring member is not compressed, thereby indicating insufficient tensioning of the fastener. The present invention offers the ability to remotely, quickly, and inexpensively verify that any number of fasteners are torqued properly upon initial installation. Where applicable, the present invention allows low cost monitoring over the life of the fastener.

Reflector dowel strength test, Fort St. Vrain

International Nuclear Information System (INIS)

Doll, D.W.

1975-01-01

The strength of the 44.45 mm (1.75 in.) diameter Fort St. Vrain (FSV) reflector dowel for loads directed radially inward toward the center of the element was measured. For a statically applied load, the strength exceeded 5783 N (1300 lb) in direct shear. This strength remained after load cycling 100 times to 4448 N (1000 lb), 10 times to 4893 N (1100 lb), 10 times to 5338 N (1200 lb), and two times to 5783 N (1300 lb). Typically, the deflection to ultimate failure was approximately 1.0 mm (0.04 in.). At about 3316 N (750 lb) and 0.20 mm (0.008 in.) deflection, one of the webs between the dowel and a coolant hole cracked, apparently redistributing the load. No further failure occurred up to the ultimate load of 5783+ N (1300+ lb)

Deposition of corrosion products from dowels on human dental root surfaces measured with proton microprobe technique

International Nuclear Information System (INIS)

Brune, D.; Brunell, G.; Lindh, U.

1982-01-01

Distribution of copper, mercury and zinc on human teeth root surfaces adjacent to dowels of gold alloy or brass as well as dowels of brass in conjunction with an amalgam crown has been measured with a proton microprobe using PIXE techniques. Upper limits of the contents of gold and silver on the root surfaces were established. Pronounced concentration profiles of copper and zinc were observed on the root surfaces of teeth prepared with dowels of brass. The dowel of gold alloy revealed only zinc deposition. The major part of copper on the root surfaces is assumed to arise from corrosion of the dowels, and has been transported to the surface by diffusion through the dential tubuli. Zinc in the volume analysed is a constituent of dentin tissue as well as a corrosion product of the brass dowel. Part of the zinc level could also be ascribed to erosion of the zinc phosphate cement matrix. The volumes analysed were (25 x 25 x 25)μm 3 . The levels of copper, mercury and zinc on the tooth root surfaces attained values up to about 200, 20 and 600 ppm, respectively. (orig.)

Deposition of corrosion products from dowels on human dental root surfaces measured with proton microprobe technique

Science.gov (United States)

Brune, D.; Brunell, G.; Lindh, U.

1982-06-01

Distribution of copper, mercury and zinc on human teeth root surfaces adjacent to dowels of gold alloy or brass as well as dowels of brass in conjunction with an amalgam crown has been measured with a proton microprobe using PIXE techniques. Upper limits of the contents of gold and silver on the root surfaces were established. Pronounced concentration profiles of copper and zinc were observed on the root surfaces of teeth prepared with dowels of brass. The dowel of gold alloy revealed only zinc deposition. The major part of copper on the root surfaces is assumed to arise from corrosion of the dowels, and has been transported to the surface by diffusion through the dential tubuli. Zinc in the volume analysed is a constituent of dentin tissue as well as a corrosion product of the brass dowel. Part of the zinc level could also be ascribed to erosion of the zinc phosphate cement matrix. The volumes analysed were (25×25×25)μm 3. The levels of copper, mercury and zinc on the tooth root surfaces attained values up to about 200, 20 and 600 ppm, respectively.

Analysis of stress- strain distribution of dowel and glue line in L-type furniture joint by means of finite element method

Directory of Open Access Journals (Sweden)

mossayeb dalvand

2017-08-01

Full Text Available In this study 3D stress-strain distribution of dowel and glue line on L-type joints made of plywood doweled was investigated. Members of joints made of 11-ply hardwood plywood (Hornbeam, Beech and Alder that were 19 mm in thickness. In this study effect of beech dowels in three levels diameters (6, 8 and 10 mm and penetration of depth (9, 13 and 17 mm on bending moment capacity of L-type joints under compression loading was investigated as experimental test, then stress-strain distribution of wood dowel and glue line in specimens were simulated by means of ANSYS 15 software with finite element method (FEM.Results have shown that bending moment resistance increased with increasing dowel diameter from 6 to 8 mm, but downward trend was observed with increasing 8 to 10 mm in dowel diameter. Bending moment resistance increased with increasing penetration depth. Also, result obtained of simulation by means of ANSYS software have shown that stress-strain in dowel and glue line increased with increasing diameter of dowel and Increasing stress in joints made of diameter dowel 10 mm due to fracture in joints and decrease in resistance once. According to results obtained of model analysis, the ultimate stress of dowel and glue line occurred in the area that joints were contacted.

Carbon nanotube plane fastener

Directory of Open Access Journals (Sweden)

Kaori Hirahara

2011-12-01

Full Text Available We report a feature of carbon nanotubes (CNTs that arises when the surfaces of two vertically-aligned CNT brushes are pressed together. Adhesion between the CNTs creates a plane fastener-like device. Observations from scanning electron microscopy and measurements of adhesion properties indicate a device-dependence on CNT density and shape near the tip region. Among other applications, such fasteners have the potential to attach small components onto micron-sized electronic devices.

Dowel Bar Retrofit Mix Design and Specification : Technical Report

Science.gov (United States)

2012-01-01

Current INDOT specifications for repair materials to be used in dowel bar retrofit (DBR) applications (Sections 507.08 and 901.07 of INDOTs Book of Specifications) are based, in large part, on the requirements of ASTM C 928 and the manufacturer-pr...

Analysis of the parameters involved in the design of slope stabilizing dowels; Analisis de las variables que intervienen en el dimensionamiento de pantalla de pasadores para contencion de deslizamientos

Energy Technology Data Exchange (ETDEWEB)

Lopez Dominguez, J. J.; Estaire Gepp, J.

2014-07-01

The use of dowels to stabilize landslides is a common practice nowadays. There are many theories, even contradictory, to design such dowels. This paper describes the methods proposed by Estaire and Sopena (2001), based on the fact that the earth pressures on the dowels, produced by the movement of the sliding ground, are equivalent to the stabilizing forces exerted by such dowels to improve the safety level of the slope. The method consists on the following steps: definition of the hydrogeological model, quantification of the initial safety level, determination of stabilization force, position of dowels in the slope, calculation of the dowel embedment and the acting load laws, election of the dowel separation and typology, and the structural design. The paper performs a critical review of some of the main design parameters: influence of the position of the dowels in the slope, the distribution of the earth pressure on the dowels and the restrains in the head of the dowels. (Author)

Improvements in remote equipment torquing and fastening

International Nuclear Information System (INIS)

Garin, J.

1978-01-01

Remote torquing and fastening is a requirement of generic interest for application in an environment not readily accessible to man. The developments over the last 30 years in torque-controlled equipment above 200 nm (150 ft/lb) have not been emphasized. The development of specialized subassemblies to torque and fasten equipment in a remotely controlled environment is an integral part of the Advanced Fuel Recycle Program at Oak Ridge National Laboratory. Commercially available subassemblies have been adapted into a system that would provide remote torquing and fastening in the range of 200 to 750 nm (150 to 550 ft/lb). 9 figures

Importance of dowels in transversal joints in concrete pavements

Science.gov (United States)

Grosek, Jiri; Chupik, Vladimir; Stryk, Josef; Brezina, Ilja

2017-09-01

Concrete pavements are designed for heavy loaded road structures. Their usage brings a number of specific issues. It is necessary to solve them all to ensure that concrete pavements will fulfil their function along the whole design period. One of these issues concerns dowels, which are located in transversal joints. Modelling of load, caused by heavy vehicles, with the use of the finite element method, provides valuable information about the stress condition of concrete pavement. The results of modelling can be verified by measurements or experiments in practice. Dowels and tie bars in jointed unreinforced concrete pavements and the importance of their correct placement, dimensions and material quality on pavement behaviour and lifespan were studied as a part of R&D projects of Technology Agency of the Czech Republic Nos. TA02031195 and TE01020168. The paper presents the experience from the modelling and performed experiments and makes conclusions which are important for the use in practice.

Removal of T-fasteners 2 days after gastrostomy is feasible.

LENUS (Irish Health Repository)

Foster, A

2009-03-01

T-fastener gastropexy is widely performed as part of gastrostomy insertion. The current literature recommends removal of T-fasteners at 2 weeks. We present a series of patients in whom T-fasteners were removed at 2 days with no major complications. We removed T-fasteners in 109 patients (male-to-female ratio 59:50, age range 18 to 88 years, mean age 62 years) at 2 days after gastrostomy insertion. Indications for gastrostomy included amytrophic lateral sclerosis, cerebrovascular accidents, head and neck carcinoma, multiple sclerosis, and others, including brain tumours and chronic inflammatory demyelinating polyneuropathy. No peritubal leaks or other major complications were seen in the study population. In the study group, 15 minor complications were recorded (14%), including localised infection and pain, both of which resolved on removal of T-fasteners. We conclude that it is feasible and safe to remove T-fasteners at 2 days.

Removal of bound metal fasteners

Science.gov (United States)

Kramer, R. F.

1981-04-01

This project explored the removal of bound metal fasteners through the use of ultrasonically assisted wrenches. Two wrenches were designed, fabricated and tested. Previous studies had indicated an increase in thread tension for a given torque application under the influence of ultrasonics. Based on this, the loosening of seized and corroded fasteners with the aid of ultrasonics was explored. Experimental data confirmed our prior analysis of the torque-tension relationship under the influence of ultrasonics; however, our progress did not satisfy the requirements necessary to loosen seized studs in a shipyard environment.

Degradation of fastener in reactor internal of PWR

Energy Technology Data Exchange (ETDEWEB)

Kim, D. W.; Ryu, W. S.; Jang, J. S.; Kim, S. H.; Kim, W. G.; Chung, M. K.; Han, C. H

2000-03-01

Main component degraded in reactor internal structure of PWR is fastener such as bolts, stud, cap screw, and pins. The failure of these components may damage nuclear fuel and limits the operation of nuclear reactor. In foreign reactors operated more than 10 years, an increasing number of incidents of degraded thread fasteners have been reported. The degradation of these components impair the integrity of reactor internal structure and limit the life extension of nuclear power plant. To solve the problem of fastener failure, the incidents of failure and main mechanisms should be investigated. the purpose of this state-of-the -art report is to investigate the failure incidents and mechanisms of fastener in foreign and domestic PWR and make a guide to select a proper materials. There is no intent to describe each event in detail in this report. This report covers the failures of fastener and damage mechanisms reported by the licensees of operating nuclear power plants and the applications of plants constructed after 1964. This information is derived from pertinent licensee event report, reportable occurrence reports, operating reactor event memoranda, failure analysis reports, and other relevant documents. (author)

A novel computer-aided method to fabricate a custom one-piece glass fiber dowel-and-core based on digitized impression and crown preparation data.

Science.gov (United States)

Chen, Zhiyu; Li, Ya; Deng, Xuliang; Wang, Xinzhi

2014-06-01

Fiber-reinforced composite dowels have been widely used for their superior biomechanical properties; however, their preformed shape cannot fit irregularly shaped root canals. This study aimed to describe a novel computer-aided method to create a custom-made one-piece dowel-and-core based on the digitization of impressions and clinical standard crown preparations. A standard maxillary die stone model containing three prepared teeth each (maxillary lateral incisor, canine, premolar) requiring dowel restorations was made. It was then mounted on an average value articulator with the mandibular stone model to simulate natural occlusion. Impressions for each tooth were obtained using vinylpolysiloxane with a sectional dual-arch tray and digitized with an optical scanner. The dowel-and-core virtual model was created by slicing 3D dowel data from impression digitization with core data selected from a standard crown preparation database of 107 records collected from clinics and digitized. The position of the chosen digital core was manually regulated to coordinate with the adjacent teeth to fulfill the crown restorative requirements. Based on virtual models, one-piece custom dowel-and-cores for three experimental teeth were milled from a glass fiber block with computer-aided manufacturing techniques. Furthermore, two patients were treated to evaluate the practicality of this new method. The one-piece glass fiber dowel-and-core made for experimental teeth fulfilled the clinical requirements for dowel restorations. Moreover, two patients were treated to validate the technique. This novel computer-aided method to create a custom one-piece glass fiber dowel-and-core proved to be practical and efficient. © 2013 by the American College of Prosthodontists.

Development of high temperature fasteners using directionally solidified eutectic alloys

Science.gov (United States)

George, F. D.

1972-01-01

The suitability of the eutectics for high temperature fasteners was investigated. Material properties were determined as a function of temperature, and included shear parallel and perpendicular to the growth direction and torsion parallel to it. Techniques for fabricating typical fastener shapes included grinding, creep forming, and direct casting. Both lamellar Ni3Al-Ni3Nb and fibrous (Co,Cr,Al)-(Cr,Co)7C3 alloys showed promise as candidate materials for high temperature fastener applications. A brief evaluation of the performance of the best fabricated fastener design was made.

Cylinder head fastening structure for internal combustion engines

Energy Technology Data Exchange (ETDEWEB)

Futakuchi, Y.; Oshiro, N.

1988-01-26

In a construction for an overhead cam internal combustion engine comprising a cylinder head adapted to be affixed to another component of the engine by at least one fastener having a tool receiving portion for tightening thereof and having a bearing cap affixed to the cylinder head and rotatably journaling the overhead camshaft, the improvement is described comprising the bearing cap having a portion overlying the fastener tool receiving portion, and means defining an access opening passing through the bearing cap and adapted to pass a tool for tightening of the fastener without removal of the bearing cap.

Hydraulic screw fastening devices - design, maintenance, operational experience

International Nuclear Information System (INIS)

Lachner.

1976-01-01

With hydraulic screw fastening devices, pretension values with a maximum deviation of +-2.5% from the rated value can be achieved. This high degree of pretension accuracy is of considerable importance with regard to the safety factor required for the screw connection between reactor vessel head and reactor vessel. The operating rhythm of a nuclear power station with its refuelling art regular intervals makes further demands on the screw fastening device, in particular in connection with the transport of screws and for nuts. The necessary installations extend the screw fastening device into a combination of a high-pressure hydraulic cylinder system with an electrical or pneumoelectrical driving unit and an electrical control unit. Maintenance work is complicated by the large number of identical, highly stressed structural elements in connection with an unfavourable relation operating time/outage time. The problems have been perpetually reduced by close cooperation between the manufacturers and users of screw fastening devices. (orig./AK) [de

Evaluation of alternative dowel bar materials and coatings : executive summary report.

Science.gov (United States)

2011-01-01

The inclusion of steel dowel bars to transfer forces across sawed or formed transverse joints from one concrete pavement slab to another while permitting expansion and contraction movements of the concrete has been a basic design practice in most U.S...

Threaded-fastener experience in nuclear power plants

International Nuclear Information System (INIS)

Koo, W.H.

1983-01-01

This report identifies 44 incidents of threaded-fastener degradation and failure in nuclear power plants from October 1964 to March 1982. It provides an overview of some of the threaded-fastener problems that have occurred since 1964. Safety implications of these incidents are discussed, and short-term regulatory actions and ongoing long-term regulatory actions are described. Information included in this report represents the current NRC staff understanding of each issue

Development of an anti-loosening fastener and comparing its ...

Indian Academy of Sciences (India)

Bikash Panja

2017-09-08

Sep 8, 2017 ... MS received 13 November 2013; revised 20 June 2016; accepted 30 April ... However, threaded fasteners may have the problem of loosening under vibrating ..... [7] Junker G H 1969 New criteria for self-loosening of fasteners.

Fastener tightening in a radioactive (hot) cell

International Nuclear Information System (INIS)

Kalk, J.J.

1986-01-01

Accurate remote tightening of fasteners in a radioactive (Hot) cell can be a very exasperating experience. Viewing can be difficult (in many places) and work sometimes must be done using mirrors and/or cameras. If electro mechanical manipulators are used, the operator has no ''feel,'' which often can result in cross threading, or improper torquing of fasteners. At the Interim Examination and Maintenance (IEM) Cell, where reactor components from the Fast Flux Test Facility (FFTF) are disassembled, these problems are prevalent because three of the IEM Cell walls have no windows. Electric impact wrenches were first proposed and tested for the IEM Cell, but the combined effects of radiation, dry argon atmosphere and poor visibility radically altered the cell tool development philosophy. This change in philosophy is reflected in the development of several simple fastener tightening devices

Fastener tightening in a radioactive (hot) cell

International Nuclear Information System (INIS)

Kalk, J.J.

1987-01-01

Accurate remote tightening of fasteners in a radioactive (hot) cell can be a very exasperating experience. Viewing can be difficult (in many places) and work sometimes must be done using mirrors and/or cameras. If electro mechanical manipulators are used, the operator has no feel, which often can result in cross threading, or improper torquing of fasteners. At the Interim Examination and Maintenance (IEM) Cell, where reactor components from the Fast Flux Testing Facility (FFTF) are disassembled, these problems are prevalent because three of the IEM Cell walls have no windows. Electric impact wrenches were first proposed and tested for the IEM Cell, but the combined effects of radiation, dry argon atmosphere and poor visibility radically altered the cell tool development philosophy. This change in philosophy is reflected in the development of several simple fastener tightening devices

Effect of Endodontic Irrigating Solutions on the Micro Push-out Bond Strength of a Fibre Glass Dowel

Directory of Open Access Journals (Sweden)

Olimpia Crispim da Silveira

2014-01-01

Full Text Available Purpose: To evaluate the effect of different endodontic irrigating solutions on the micro push-out bond strength of a fiber glass dowel. Material and Methods: Seventy 16-mm long root segments of bovine incisors were prepared and randomly assigned to 7 groups (n=10 according to the type of irrigating solution used prior to the cementation of the intra-radicular fiber glass dowels: G1: 5.25% NaOCl + 17% EDTA; G2: 5.25% NaOCl; G3: 17% EDTA; G4: 2% chlorhexidine gel; G5: 70% alcohol; G6: 11.5% polyacrylic acid; and G7: saline (control. After treatment of intracanal dentin, the glass fibre dowels were cemented with self-adhesive resin cement (RelyX Unicem. Six slices with the thickness of 1.00 ± 0.05 mm were obtained from each tooth at the coronal, middle and apical root thirds (2 slices per third using a low-speed saw. Micro push-out tests were performed at a crosshead speed of 0.5mm/min and the data (MPa were analyzed statistically by ANOVA and Tukey’s and Dunnett’s tests. Results: There were statistically significant differences (p<0.0001 among the irrigating solutions, but no significant difference (p=0.0591 was found among the root thirds. G5 presented the highest bond strength mean of all groups (p<0.0001. The use of 70% alcohol increased the adhesion values by 53% compared to the group control. Conclusion: The use of 70% alcohol increased the bond strength of the fiber glass dowel to the dentin walls. However, the push-out bond strength between the dowel and the root dentin was not affected by the root third (coronal, middle and apical.

Double fastener-type contamination protective cloth

International Nuclear Information System (INIS)

Nomura, Norio.

1996-01-01

In the cloth of the present invention, a hood portion covering the entire of a head and a suit portion having an upper half body portion and a lower half body portion connected to the upper half portion for covering from a neck to ankles are made integrated. The suit portion has long sleeves at the upper half body portion, and has strait leg portions at the lower half body portion. Two linear sliding fasteners are disposed from the neck portion on the front surface of the suit portion to the lower edges of both ankle portions. The sliding fasteners have a double structure having a folded portion at the inner side. Slits are formed on the outer side surfaces of each of the ankle portions and openable/closable face fasteners are attached. A rubber is incorporated in the wrist portions at the top ends of the long sleeves to be in close contact with the wrists. An operator can easily put on and off the cloth without withdrawing legs. Accordingly, radioactive contamination can be prevented upon putting on and off the cloth. (I.N.)

Corrosion rates of fasteners in treated wood exposed to 100% relative humidity

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2009-01-01

In the past, gravimetric corrosion data for fasteners exposed to treated wood has been reported as a percent weight loss. Although percent weight loss is a valid measure of corrosion for comparing identical fasteners, it can distort the corrosion performance of fasteners with different geometries and densities. This report reevaluates a key report on the corrosiveness...

A novel method for detecting second harmonic ultrasonic components generated from fastened bolts

Science.gov (United States)

Fukuda, Makoto; Imano, Kazuhiko

2012-09-01

This study examines the use of ultrasonic second harmonic components in the quality control of bolt-fastened structures. An improved method for detecting the second harmonic components, from a bolt fastened with a nut, using the transmission method is constructed. A hexagon head iron bolt (12-mm diameter and 25-mm long) was used in the experiments. The bolt was fastened using a digital torque wrench. The second harmonic component increased by approximately 20 dB before and after the bolt was fastened. The sources of second harmonic components were contact acoustic nonlinearity in the screw thread interfaces of the bolt-nut and were the plastic deformation in the bolt with fastening bolt. This result was improved by approximately 10 dB compared with previous our method. Consequently, usefulness of the novel method for detecting second harmonic ultrasonic components generated from fastened bolt was confirmed.

Advantages of DVW reinforced moment transmitting timber joints with steel flitch plates for colum-beam application

NARCIS (Netherlands)

Leijten, A.J.M.; Brandon, D.; Haddad, Y.M.

2013-01-01

This paper presents a study into the moment-rotation aspects of dvw (densified veneer wood) reinforced timber connections with an inter-connecting flitch plate used as middle member. Previous studies showed that reinforcing dowel-type timber connections with dvw and using expanded tube fasteners

Investigation of Fastening Performance of Subminiature Serrated Bolt

Energy Technology Data Exchange (ETDEWEB)

Jang, Myung Guen; Jeong, Jin Hwan; Jang, Yeon Hui; Kim, Hee Cheol; Kim, Jong-Bong [Seoul Nat’l Univ. of Science & Tech, Seoul (Korea, Republic of)

2017-04-15

As the size of electric products such as mobile phones and smart watches decrease, the bolts used to assemble these products should also be miniaturized. A miniature-sized bolt has to provide sufficient joining torque and anti-releasing torque to keep the components together. We studied a serrated bolt as a candidate for a miniature-sized fastener to increase the anti-releasing torque. In a serrated bolt, a serrated shape is formed on the bottom surface of the bolt head to create an obstacle to releasing. In this study, finite element analyses for the joining and releasing of bolts were carried out, and the anti-releasing performance was predicted. Based on the results of analyses using various numbers of serrations and fastening depths, the effects of the number of serrations and fastening depth on the anti-releasing performance were investigated.

Investigation of Fastening Performance of Subminiature Serrated Bolt

International Nuclear Information System (INIS)

Jang, Myung Guen; Jeong, Jin Hwan; Jang, Yeon Hui; Kim, Hee Cheol; Kim, Jong-Bong

2017-01-01

As the size of electric products such as mobile phones and smart watches decrease, the bolts used to assemble these products should also be miniaturized. A miniature-sized bolt has to provide sufficient joining torque and anti-releasing torque to keep the components together. We studied a serrated bolt as a candidate for a miniature-sized fastener to increase the anti-releasing torque. In a serrated bolt, a serrated shape is formed on the bottom surface of the bolt head to create an obstacle to releasing. In this study, finite element analyses for the joining and releasing of bolts were carried out, and the anti-releasing performance was predicted. Based on the results of analyses using various numbers of serrations and fastening depths, the effects of the number of serrations and fastening depth on the anti-releasing performance were investigated.

Economical bridge solutions based on innovative composite dowels and integrated abutments ecobridge

CERN Document Server

Băncilă, Radu

2015-01-01

This book is an outcome of the research project “ECOBRIDGE – Demonstration of ECOnomical BRIDGE solutions based on innovative composite dowels and integrated abutments – RFCS – CT 2010-00024”, which has been co-funded by the Research Fund for Coal and Steel (R.F.C.S.) of the European Community. The main topics of the book are the following: design of integral bridges, innovative composite dowels for the shear transmission, construction of bridges, structural analysis of bridges and monitoring. The book joins the technical experience and the contributions of the involved research partners. The technical content of all the papers is present-day in the field of the design, construction and monitoring of innovative composite bridges. The efficient design and construction improve and consolidate the market position of steel construction and steel producing industry. In addition, the advanced forms of construction are contributing to savings in material and energy consumption for the structure during prod...

Needs assessment of school and community physical activity opportunities in rural West Virginia: the McDowell CHOICES planning effort

OpenAIRE

Kristjansson, Alfgeir L; Elliott, Eloise; Bulger, Sean; Jones, Emily; Taliaferro, Andrea R; Neal, William

2015-01-01

Background McDowell CHOICES (Coordinated Health Opportunities Involving Communities, Environments, and Schools) Project is a county wide endeavor aimed at increasing opportunities for physical activity (PA) in McDowell County, West Virginia (WV). A comprehensive needs-assessment laid the foundation of the project. Methods During the 6?month needs assessment, multiple sources of data were collected in two Town Hall Meetings (n?=?80); a student online PA interest survey (n?=?465); a PA and nutr...

Needs assessment of school and community physical activity opportunities in rural West Virginia: the McDowell CHOICES planning effort.

Science.gov (United States)

Kristjansson, Alfgeir L; Elliott, Eloise; Bulger, Sean; Jones, Emily; Taliaferro, Andrea R; Neal, William

2015-04-03

McDowell CHOICES (Coordinated Health Opportunities Involving Communities, Environments, and Schools) Project is a county wide endeavor aimed at increasing opportunities for physical activity (PA) in McDowell County, West Virginia (WV). A comprehensive needs-assessment laid the foundation of the project. During the 6 month needs assessment, multiple sources of data were collected in two Town Hall Meetings (n = 80); a student online PA interest survey (n = 465); a PA and nutrition survey among 5(th) (10-11 years) and 8(th) graders (13-14 years) with questions adapted from the CDC's Youth Risk Behavior Surveillance Survey (n = 442, response rate = 82.2%); six semi-structured school and community focus groups (n = 44); school site visits (n = 11); and BMI screening (n = 550, response rate = 69.7%). One third of children in McDowell County meet the national PA minimum of 60 minutes daily. At least 40% of 5(th) and 8(th) graders engage in electronic screen activity for 3 hours or more every day. The prevalence of obesity in 5(th) graders is higher in McDowell County than the rest of WV (~55% vs. 47% respectively). SWOT analyses of focus group data suggest an overall interest in PA but also highlight a need for increase in structured PA opportunities. Focus group data also suggested that a central communication (e.g. internet-based) platform would be beneficial to advertise and boost participation both in current and future programs. Schools were commonly mentioned as potential facilities for public PA participation throughout the county, both with regards to access and convenience. School site visits suggest that schools need more equipment and resources for before, during, and after school programs. An overwhelming majority of participants in the McDowell CHOICES needs assessment were interested to participate in more PA programs throughout the county as well as to improve opportunities for the provision of such programs. Public schools were widely recognized as the hub

Factors influencing power hand tool fastening accuracy and reaction forces.

Science.gov (United States)

Radwin, Robert G; Chourasia, Amrish O; Howery, Robert S; Fronczak, Frank J; Yen, Thomas Y; Subedi, Yashpal; Sesto, Mary E

2014-06-01

A laboratory study investigated the relationship between power hand tool and task-related factors affecting threaded fastener torque accuracy and associated handle reaction force. We previously developed a biodynamic model to predict handle reaction forces. We hypothesized that torque accuracy was related to the same factors that affect operator capacity to react against impulsive tool forces, as predicted by the model. The independent variables included tool (pistol grip on a vertical surface, right angle on a horizontal surface), fastener torque rate (hard, soft), horizontal distance (30 cm and 60 cm), and vertical distance (80 cm, 110 cm, and 140 cm). Ten participants (five male and five female) fastened 12 similar bolts for each experimental condition. Average torque error (audited - target torque) was affected by fastener torque rate and operator position. Torque error decreased 33% for soft torque rates, whereas handle forces greatly increased (170%). Torque error also decreased for the far horizontal distance 7% to 14%, when vertical distance was in the middle or high, but handle force decreased slightly 3% to 5%. The evidence suggests that although both tool and task factors affect fastening accuracy, they each influence handle reaction forces differently. We conclude that these differences are attributed to different parameters each factor influences affecting the dynamics of threaded faster tool operation. Fastener torque rate affects the tool dynamics, whereas posture affects the spring-mass-damping biodynamic properties of the human operator. The prediction of handle reaction force using an operator biodynamic model may be useful for codifying complex and unobvious relationships between tool and task factors for minimizing torque error while controlling handle force.

Velcro-like fasteners based on NiTi micro-hook arrays

International Nuclear Information System (INIS)

Vokoun, D; Pilch, J; Majtás, D; Šittner, P; Sedlák, P; Frost, M

2011-01-01

A recently developed Velcro-like fastener utilizes superelastic deformation of two interlocked NiTi hooks when pulled apart. This work focuses on experimental analysis (evaluation of normal detachment force at different temperatures) and modeling (simulation by a finite element implemented SMA model) of the unhooking process. It is claimed that nonlinear superelastic deformation of NiTi leads to unique properties of the NiTi hook fasteners such as high strength (∼15 000 kg m −2 ), a significant increase of strength with increasing temperature, absorption of impact loads, damping of mechanical vibrations, forceless contact or silent release and better functioning in dirty environments compared to conventional Velcro fasteners

Fastening, coupling and joining technique between diaspora and irredenta

Science.gov (United States)

Bauer, C.-O.

1980-06-01

The problem of eliminating the present divergence and shattering (diaspora) in the treatment of problems of the fastening, coupling, and joining technique on different technical branches is examined. It is shown that by an appropriate independence the fastening, coupling and joining techniques can recognize and consequently utilize the numerous performance reserves which are concealed by the present organization and action due to the lack of systematically tended works.

Long-term load–deformation behaviour of timber–concrete joints

NARCIS (Netherlands)

Van de Kuilen, J.W.G.; Dias, A.M.P.G.

2011-01-01

This paper discusses the long-term mechanical behaviour of timber-to-concrete joints made with dowel-type fasteners. Despite the influence that the long-term behaviour of joints has on the mechanical behaviour of a timber–concrete structure and consequently on its design, there is still a lack of

The Automated Threaded Fastening Based on On-line Identification

Directory of Open Access Journals (Sweden)

Nicolas Ivan Giannoccaro

2008-11-01

Full Text Available The principle of the thread fastenings have been known and used for decades with the purpose of joining one component to another. Threaded fastenings are popular because they permit easy disassembly for maintenance, repair, relocation and recycling. Screw insertions are typically carried out manually. It is a difficult problem to automat. As a result there is very little published research on automating threaded fastenings, and most research on automated assembly focus on the peg-in-hole assembly problem. This paper investigates the problem of automated monitoring of the screw insertion process. The monitoring problem deals with predicting integrity of a threaded insertion, based on the torque vs. insertion depth curve generated during the insertions. The authors have developed an analytical model to predict the torque signature signals during self-tapping screw insertions. However, the model requires parameters on the screw dimensions and plate material properties are difficult to measure. This paper presents a study on on-line identification during screw fastenings. An identification methodology for two unknown parameter estimation during a self-tapping screw insertion process is presented. It is shown that friction and screw properties required by the model can be reliably estimated on-line. Experimental results are presented to validate the identification procedure.

Compilation of fastener testing data received in response to NRC Compliance Bulletin 87-02

International Nuclear Information System (INIS)

Cwalina, G.C.; Conway, J.T.; Parker, L.B.

1989-06-01

On November 6, 1987, the Nuclear Regulatory Commission (NRC) issued Bulletin 87-02, ''Fastener Testing to Determine Conformance With Applicable Material Specifications,'' to all holders of operating licenses or construction permits for nuclear power reactors (licensees). The bulletin was issued so that the NRC staff could gather data to determine whether counterfeit fasteners are a problem in the nuclear power industry. The bulletin requested nuclear power plant owners to determine whether fasteners obtained from suppliers and/or manufacturers for use in their facilities meet the mechanical and chemical specifications stipulated in the procurement documents. The licensees were requested to sample a minimum of 10 safety-related and 10 non-safety-related fasteners (studs, bolts, and/or cap screws) and a sample of typical nuts that would be used with each fastener and to report the testing results to the NRC. The results of this study did not indicate a safety concern relating to the use of mismarked or counterfeit fasteners in the nuclear industry, but they did indicate a nonconformance rate of 8 to 12 percent for fasteners. The NRC staff is considering taking action to improve the effectiveness of receipt inspection and testing programs for all materials at nuclear power plants

Prevailing Torque Locking Feature in Threaded Fasteners Using Anaerobic Adhesive

Science.gov (United States)

Hernandez, Alan; Hess, Daniel P.

2016-01-01

This paper presents results from tests to assess the use of anaerobic adhesive for providing a prevailing torque locking feature in threaded fasteners. Test procedures are developed and tests are performed on three fastener materials, four anaerobic adhesives, and both unseated assembly conditions. Five to ten samples are tested for each combination. Tests for initial use, reuse without additional adhesive, and reuse with additional adhesive are performed for all samples. A 48-hour cure time was used for all initial use and reuse tests. Test data are presented as removal torque versus removal angle with the specification required prevailing torque range added for performance assessment. Percent specification pass rates for the all combinations of fastener material, adhesive, and assembly condition are tabulated and reveal use of anaerobic adhesive as a prevailing torque locking feature is viable. Although not every possible fastener material and anaerobic adhesive combination provides prevailing torque values within specification, any combination can be assessed using the test procedures presented. Reuse without additional anaerobic adhesive generally provides some prevailing torque, and in some cases within specification. Reuse with additional adhesive often provides comparable removal torque data as in initial use.

Component assembly with shape memory polymer fastener for microrobots

Science.gov (United States)

Kim, Ji-Suk; Lee, Dae-Young; Koh, Je-Sung; Jung, Gwang-Pil; Cho, Kyu-Jin

2014-01-01

Adhesives are generally used for the assembly of microrobots, whereas bolts, screws, or rivets are used for larger robots. Although adhesives are easy to apply, lightweight, and small, they cannot be used for repeated assembly and disassembly of parts. In this paper, we present a novel microfastener composed of a polyurethane-based shape memory polymer (SMP) that is lightweight and small but that is easily detached for disassembly. This was achieved by using the shape recovery and modulus change of the SMP. A sheet of macromolded SMP was laser machined into an I-beam-shaped rivet, and notches were added to the structure to prevent stress concentration. Pull-off tests showed that, as the notch radius increased, the disengagement strength of the rivet fastener decreased and the reusability increased. Through the elastoplastic model, a single SMP rivet was calculated to have maximum disengagement strength of 150 N cm-2 in the elastic range, depending on the notch radius. The fasteners were applied to a jumping microrobot. The legs and body were assembled with ten fasteners, which showed no permanent deformation after impact during jumping movements. The legs were easily replaced with ones of different stiffness by heating the engaged sites to make the fasteners compliant and detachable. The proposed detachable SMP microfasteners are particularly useful for testing the isolated performance of microrobot components to determine the optimal designs for these components.

Fastener investigation in JET

Energy Technology Data Exchange (ETDEWEB)

Bunting, P., E-mail: patrick.bunting@ccfe.ac.uk; Thompson, V.; Riccardo, V.

2016-11-15

Highlights: • Experimental work to identify the cause of a bolt seizure inside the JET vessel. • Taguchi method used to reduce tests to 16 while covering 5 parameters. • Experimental work was unable to reproduce bolt seizure. • Thread contamination had little effect on the bolt performance. - Abstract: JET is an experimental fusion reactor consisting of magnetically confined, high temperature plasma inside a large ultra-high vacuum chamber. The inside of the chamber is protected from the hot plasma with tiles made from beryllium, tungsten, carbon composites and other materials bolted to the vessel wall. The study was carried out in response to a JET fastener seizing inside the vacuum vessel. The following study looks at characterising the magnitude of the individual factors affecting the fastener break away torque. This was carried out using a statistical approach, the Taguchi method: isolating the net effect of individual factors present in a series of tests [1](Grove and Davis, 1992). Given the severe environment within the JET vessel due to the combination of heat, ultra-high vacuum and the high contact pressure in bolt threads, the contributions of localised diffusion bonding is assessed in conjunction with various combinations of bolt and insert material.

Fastener Corrosion: A Result of Moisture Problems in the Building Envelope

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

This paper reviews recent literature on the corrosion of metals embedded in wood and highlights the link be-tween moisture accumulation in wood and fastener cor-rosion. Mechanisms of fastener corrosion are described including dependence upon wood moisture content. These fundamental concepts are applied to practical examples by explaining how hygrothermal models can be...

Numerical Analysis of Thermal Stresses around Fasteners in Composite Metal Foils

Science.gov (United States)

Nammi, S. K.; Butt, J.; –L Mauricette, J.; Shirvani, H.

2017-12-01

The process of composite metal foil manufacturing (CMFM) has reduced a number of limitations associated with commercial additive manufacturing (AM) methods. The existing metal AM machines are restricted by their build envelope and there is a growing market for the manufacture of large parts using AM. These parts are subsequently manufactured in fragments and are fastened together. This paper analyses the thermal stresses around cylindrical fasteners for three layered metal composite parts consisting of aluminium foil, brazing paste and copper foil layers. The investigation aims to examine the mechanical integrity of the metallurgically bonded aluminium/copper foils of 100 micron thickness manufactured in a disc shape. A cylindrical fastener set at an elevated temperature of 100 °C is fitted in the middle of the disc which results in a steady-state thermal distribution. Radial and shear stresses are computed using finite element method which shows that non-zero shear stresses developed by the copper layer inhibit the axial slippage of the fastener and thereby establishing the suitability of rivet joints for CMFM parts.

Component assembly with shape memory polymer fastener for microrobots

International Nuclear Information System (INIS)

Kim, Ji-Suk; Lee, Dae-Young; Koh, Je-Sung; Jung, Gwang-Pil; Cho, Kyu-Jin

2014-01-01

Adhesives are generally used for the assembly of microrobots, whereas bolts, screws, or rivets are used for larger robots. Although adhesives are easy to apply, lightweight, and small, they cannot be used for repeated assembly and disassembly of parts. In this paper, we present a novel microfastener composed of a polyurethane-based shape memory polymer (SMP) that is lightweight and small but that is easily detached for disassembly. This was achieved by using the shape recovery and modulus change of the SMP. A sheet of macromolded SMP was laser machined into an I-beam-shaped rivet, and notches were added to the structure to prevent stress concentration. Pull-off tests showed that, as the notch radius increased, the disengagement strength of the rivet fastener decreased and the reusability increased. Through the elastoplastic model, a single SMP rivet was calculated to have maximum disengagement strength of 150 N cm −2 in the elastic range, depending on the notch radius. The fasteners were applied to a jumping microrobot. The legs and body were assembled with ten fasteners, which showed no permanent deformation after impact during jumping movements. The legs were easily replaced with ones of different stiffness by heating the engaged sites to make the fasteners compliant and detachable. The proposed detachable SMP microfasteners are particularly useful for testing the isolated performance of microrobot components to determine the optimal designs for these components. (paper)

A structural health monitoring fastener for tracking fatigue crack growth in bolted metallic joints

Science.gov (United States)

Rakow, Alexi Schroder

Fatigue cracks initiating at fastener hole locations in metallic components are among the most common form of airframe damage. The fastener hole site has been surveyed as the second leading initiation site for fatigue related accidents of fixed wing aircraft. Current methods for inspecting airframes for these cracks are manual, whereby inspectors rely on non-destructive inspection equipment or hand-held probes to scan over areas of a structure. Use of this equipment often demands disassembly of the vehicle to search appropriate hole locations for cracks, which elevates the complexity and cost of these maintenance inspections. Improved reliability, safety, and reduced cost of such maintenance can be realized by the permanent integration of sensors with a structure to detect this damage. Such an integrated system of sensors would form a structural health monitoring (SHM) system. In this study, an Additive, Interleaved, Multi-layer Electromagnetic (AIME) sensor was developed and integrated with the shank of a fastener to form a SHM Fastener, a new SHM technology targeted at detection of fastener hole cracks. The major advantages of the SHM Fastener are its installation, which does not require joint layer disassembly, its capability to detect inner layer cracks, and its capability to operate in a continuous autonomous mode. Two methods for fabricating the proposed SHM Fastener were studied. The first option consisted of a thin flexible printed circuit film that was bonded around a thin metallic sleeve placed around the fastener shank. The second option consisted of coating sensor materials directly to the shank of a part in an effort to increase the durability of the sensor under severe loading conditions. Both analytical and numerical models were developed to characterize the capability of the sensors and provide a design tool for the sensor layout. A diagnostic technique for crack growth monitoring was developed to complete the SHM system, which consists of the

Lapped scarf joint with inclined faces and wooden dowels: Experimental and numerical analysis

Czech Academy of Sciences Publication Activity Database

Arciszewska-Kędzior, Anna; Kunecký, Jiří; Hasníková, Hana; Sebera, V.

2015-01-01

Roč. 94, July (2015), s. 1-8 ISSN 0141-0296 R&D Projects: GA MK(CZ) DF12P01OVV004 Keywords : timber joint * wooden-dowels * full-scale experiments * FEM * failure criterion Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 1.893, year: 2015 http://www.sciencedirect.com/science/article/pii/S0141029615001807

Reversible fastener clamp load monitor with continuous visual or remote readout

Science.gov (United States)

Hodge, Malcolm H.; Kausel, Theodore C., Jr.; Begley, Matthew R.

1998-03-01

SIMS has developed a simple means for detecting and monitoring both absolute and relative clamp load, or bolt tension, in fastener systems. More than twenty-five percent of automotive failures are known to be due to undetected loss of fastener clamp load. While the equivalent aerospace maintenance statistics are not known, the average automobile has 3,500 fasteners while a Boeing 747 has closer to one million. It is therefore anticipated that the new SensaBolt clamp load tracking system could find wide applications in the aerospace arena. We describe a visually-evident and retrofitted clamp load monitoring design which is based on the differential joint substrate compression at, and immediately adjacent to, the fastener location. This intrinsically-accurate indicator does not necessarily require alteration in either the bolt or nut geometries, thereby facilitating product introduction and retrofit in aging aircraft applications. In addition, SensaBolt's sole reliance on substrate compression renders it more accurate then torque wrench or turn-of-nut techniques. Readout may be accomplished by any of three principal methods: for those applications with ease of access to the sensor, loss of tension can be determined by direct visual inspection. Application of a standard wrench can then be made to restore the fastener's proper tightness, per the SensaBolt indicators. In those instances where line-of-sight is unimpeded and more formal inspection is desired, the SensaBolt may be interrogated by a laser scanner bar code reader. Finally, SensaBolt may be addressed by the SIMS fiber optic harness for those instances where full-time remote interrogation is desired.

Review of Bolt Preload and Torque for Assembling Threaded Fasteners in Nuclear Power Plant

International Nuclear Information System (INIS)

Lee, Yong-Sung; Lee, Jae-Gon; Kang, Yong-Chul; Shin, Ki-Jong

2007-01-01

There are numerous threaded fasteners such as bolts, studs, nuts, cap screws and anchor bolts used in nuclear power plants(NPPs). The major applications of threaded fasteners are reactor coolant pressure boundary components, their internals and supports. With the increase of commercial operation period of NPPs, the incidents caused by degradation of threaded fasteners have been occurred. A large number of reported incidents are involved in the pressure boundary and major component supports. The degradation and failure of threaded fasteners is affected by material, preload and torque value at assembly, bolting practice, etc. It is very important to select appropriate bolt preload and decide assembly torque value because torque control using a torque wrench is the most common method in a power plant to assemble a bolted flange connection. Many researches have been studied to define the proper bolt preload and desired torque value with regard to the integrity of bolted connections including pressure boundary joints by EPRI and other plant industry. But in domestic NPPs, considerably few works are done on the bolted joint assembly in spite of increasing events related with threaded faster. Therefore we investigated degradation or failure of the threaded fasteners used in NPPs, also examined the codes, standards and technical trends concerning bolt preload and assembly torque in NPPs. It is the purpose of this study to provide proper technical information for assuring integrity of the threaded fasteners

Alloy and composition dependence of hydrogen embrittlement susceptibility in high-strength steel fasteners

Science.gov (United States)

Brahimi, S. V.; Yue, S.; Sriraman, K. R.

2017-06-01

High-strength steel fasteners characterized by tensile strengths above 1100 MPa are often used in critical applications where a failure can have catastrophic consequences. Preventing hydrogen embrittlement (HE) failure is a fundamental concern implicating the entire fastener supply chain. Research is typically conducted under idealized conditions that cannot be translated into know-how prescribed in fastener industry standards and practices. Additionally, inconsistencies and even contradictions in fastener industry standards have led to much confusion and many preventable or misdiagnosed fastener failures. HE susceptibility is a function of the material condition, which is comprehensively described by the metallurgical and mechanical properties. Material strength has a first-order effect on HE susceptibility, which increases significantly above 1200 MPa and is characterized by a ductile-brittle transition. For a given concentration of hydrogen and at equal strength, the critical strength above which the ductile-brittle transition begins can vary due to second-order effects of chemistry, tempering temperature and sub-microstructure. Additionally, non-homogeneity of the metallurgical structure resulting from poorly controlled heat treatment, impurities and non-metallic inclusions can increase HE susceptibility of steel in ways that are measurable but unpredictable. Below 1200 MPa, non-conforming quality is often the root cause of real-life failures. This article is part of the themed issue 'The challenges of hydrogen and metals'.

Automation of calculation of fastening of non-standard freights on sea vessels

Directory of Open Access Journals (Sweden)

Андрій Валерійович Пархотько

2015-11-01

Full Text Available Correct positioning and fastening of freights are important safety conditions of navigation. Unreliable positioning and fastening of freights results in shipwreck and is the reason for injuries and losses of human lives both in the sea and during loading and unloading. To solve the above-mentioned problems, the International Maritime Organization publishes manuals in the form of either the Assembly resolutions, or the circulars approved by Maritime Safety Committee. The correct definition of necessary quantity of lashings and their positioning has the greatest impact on safe fastening of freights. The sea being rough, the vessel is accelerated both in longitudinal, and vertical and prevailing cross directions. The forces created by these accelerations generate the majority of the problems in fastening. The order of calculations of the force moments and forces acting upon the freights being shipped by sea vessels has been shown in the article. To know the proper number of lashings the calculations of the forces acting upon the freights being shipped as compared with the forces holding the freights and taking into account the strength, the number and the fastening angle of the lashings must be made. Оption of realization of algorithm of calculation with use of the а computer program to make these calculations has been offered. Some recommendations so that the program could be used by the management of the vessel, the surveyor companies and technologists of the port have been given as well as an example of such a calculation

Three-Dimensional Heat Transfer Analysis of Metal Fasteners in Roofing Assemblies

Directory of Open Access Journals (Sweden)

Manan Singh

2016-11-01

Full Text Available Heat transfer analysis was performed on typical roofing assemblies using HEAT3, a three-dimensional heat transfer analysis software. The difference in heat transferred through the roofing assemblies considered is compared between two cases—without any steel fasteners and with steel fasteners. In the latter case, the metal roofing fasteners were arranged as per Factor Mutual Global (FMG approvals, in the field, perimeter, and corner zones of the roof. The temperature conditions used for the analysis represented summer and winter conditions for three separate Climate Zones (CZ namely Climate Zone 2 or CZ2 represented by Orlando, FL; CZ3 represented by Atlanta, GA; and CZ6 zone represented by St. Paul, MN. In all the climatic conditions, higher energy transfer was observed with increase in the number of metal fasteners attributed to high thermal conductivity of metals as compared to the insulation and other materials used in the roofing assembly. This difference in heat loss was also quantified in the form of percentage change in the overall or effective insulation of the roofing assembly for better understanding of the practical aspects. Besides, a comparison of 2D heat transfer analysis (using THERM software and 3D analysis using HEAT3 is also discussed proving the relevance of 3D over 2D heat transfer analysis.

Effects of long-term exposure on LDEF fastener assemblies

Science.gov (United States)

Spear, Steve; Dursch, Harry

1992-09-01

This presentation summarizes the Systems Special Investigations Group (SIG) findings from testing and analysis of fastener assemblies used on the Long Duration Exposure Facility (LDEF) structure, the tray mounting clamps, and by the various experimenters. The LDEF deintegration team and several experimenters noted severe fastener damage and hardware removal difficulties during post-flight activities. The System SIG has investigated all reported instances, and in all cases examined to date, the difficulties were attributed to galling during installation or post-flight removal. To date, no evidence of coldwelding was found. Correct selection of materials and lubricants as well as proper mechanical procedures is essential to ensure successful on-orbit or post-flight installation and removal of hardware.

Tempering of martensitic steel for fasteners: Effects of micro-alloying on microstructure and mechanical property evolution

OpenAIRE

Öhlund, C.E.I.C.

2015-01-01

The research presented in this thesis aims to deepen our understanding of the effect of micro-alloying on the microstructure and mechanical property evolution during tempering of martensitic steel for fasteners. The ongoing trend of engine down-sizing has led to the need for stronger and more temperature resistant fasteners than currently available according to international standards. A new martensitic fastener steel called KNDS4 has been developed, that combines higher strength with improve...

Torque Tension Testing of Fasteners used for NASA Flight Hardware Applications

Science.gov (United States)

Hemminger, Edgar G.; Posey, Alan J.; Dube, Michael J.

2014-01-01

The effect of various lubricants and other compounds on fastener torque-tension relationships is evaluated. Testing was performed using a unique test apparatus developed by Posey at the NASA Goddard Space Flight Center. A description of the test methodology, including associated data collection and analysis will be presented. Test results for 300 series CRES and A286 heat resistant fasteners, torqued into various types of inserts will be presented. The primary objective of this testing was to obtain torque-tension data for use on NASA flight projects.

Mounting Systems for Structural Members, Fastening Assemblies Thereof, and Vibration Isolation Systems Including the Same

Science.gov (United States)

Young, Ken (Inventor); Hindle, Timothy (Inventor); Barber, Tim Daniel (Inventor)

2016-01-01

Mounting systems for structural members, fastening assemblies thereof, and vibration isolation systems including the same are provided. Mounting systems comprise a pair of mounting brackets, each clamped against a fastening assembly forming a mounting assembly. Fastening assemblies comprise a spherical rod end comprising a spherical member having a through opening and an integrally threaded shaft, first and second seating members on opposite sides of the spherical member and each having a through opening that is substantially coaxial with the spherical member through opening, and a partially threaded fastener that threadably engages each mounting bracket forming the mounting assembly. Structural members have axial end portions, each releasably coupled to a mounting bracket by the integrally threaded shaft. Axial end portions are threaded in opposite directions for permitting structural member rotation to adjust a length thereof to a substantially zero strain position. Structural members may be vibration isolator struts in vibration isolation systems.

McDowell e as estátuas de Dédalo

Directory of Open Access Journals (Sweden)

João Carlos Brum Torres

Full Text Available ABSTRACT The subject of this paper is the concept of 'demonstrative concept', which has been introduced in philosophy by John McDowell in Mind and World. The analysis presented in the article has a reconstructive and a critical character. Its reconstructive drive may be viewed as required by the concise mode the philosopher adopted to present his theoretical innovation and comprehends an effort to make clear: (i what is the difference between the temporal conditions necessary (a to give conceptual status to the color shade we have before our eyes and (b to our possession of ordinary concepts; (ii the sui generis character of the universality proper to demonstrative concepts and the uniformity of their relations to what they are concepts of; (iii the equivalence of their semantical regime to that which is proper to concepts of measurement standards; (iv the very singular function performed by memory in the constitution and possession of demonstrative concepts. Now, the critical character of the paper firstly lies in the remark that there is a kind of inconsequence in the way McDowell conceives the employment of those concepts, namely in his refusal to admit that even though it is natural to say 'I see the shade in my mind's eye', it would be a mistake to think that when we recognize a color shade as being the same as the one we have seen before there is an inner comparison of it with the retained sample. The second of the paper critical points is the warning that, considering the complex constitution process of demonstrative concepts and its exacting semantic, it seems impossible to take them as coextensive to our human experience of colors.

Finite element analysis of adanced composite structures containing mechanically fastened joints

International Nuclear Information System (INIS)

Baumann, E.

1982-01-01

Although the usual engineering practice is to ignore joint effects in finite element models of overall structures, there are times when the inclusion of fastener effects in a model is necessary for accurate analysis. This paper describes some simple but accurate methods for accommodating this modeling requirement. The approach involves correlation of test results from a few composite mechanically fastened joints with finite element analyses of joints. It is assumed that if the fastener actions in the test articles can be properly predicted by simple finite element techniques, then these same techniques can be applied to large overall structure models. During the course of this test-analysis effort it was determined that it is possible to obtain correct results for overall structure-joint analyses by using simple modeling concepts provided special care is employed. Also, some emphasis is given in this paper to the importance of properly reducing test data in order to obtain meaningful correlations with finite element analysis. Finally, for those interested, the appendix contains brief descriptions of the test results and failure modes explored in the test program. (orig.)

NRC Bulletin No. 87-02, Supplement 1: Fastener testing to determine conformance with applicable material specifications

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

Item 5 of NRC Compliance Bulletin 87-02 requested that all holders of operating licenses or construction permits for nuclear power reactors information regarding the identity of the suppliers and manufacturers of the safety-related and non-safety-related fasteners selected for testing. After further consideration, the NRC has determined that it needs information regarding the identity of all vendors from which safety-related and non-safety-related fasteners have been obtained within the past 10 years, a reasonable period which will not put undue burden on addressees. This information will assist the NRC in determining whether nuclear facility fasteners in use have been supplied in accordance with their intended use. In addition, this information is needed so that the NRC can properly coordinate information with other government agencies concerned with problems identified in the quality of fasteners

METHOD DELAING WITH THE PROBLEM OF DOWEL BAR CONNECTIONS DURING THE RESTORATION WORK IN PREOBRAZHENSKAYA CHURCH IN KIZHI ISLAND

Directory of Open Access Journals (Sweden)

Алёна Юрьевна Лазарева

2016-05-01

Full Text Available In this paper we make an attempt to chose and justify the method for the solution of the dowel bars connection problem in diagonal walls when carrying out restoration work on the Preobrazhenskaya Church in Kizhi. Since 1980, the church has experiances multiple restoration works. At the moment, it is restored in most of the structural zones and it is required to choose the most optimal scheme and install pegs, and their numbers increase in the average to complete the quadrangle at the top of the octagon. Consequently, the study identifies the causes of large deformations of the church as a result of detailed examination. Moreover, it was found out that the most effective method for solution of dowel bar construction is the Monte Carlo method, which allows finding applying by the method of mathematical modeling.

Smart fastener for KC-135 structural integrity monitoring

Science.gov (United States)

Schoess, Jeffrey N.; Seifert, Greg

1997-06-01

Hidden and inaccessible corrosion in aircraft structures is the number-one logistics problem for the U.S. Air Force, with an estimated maintenance cost in excess of $DOL1.0 billion per year in 1990-equivalent dollars. The Smart Aircraft Fastener Evaluation (SAFE) system is being developed to provide early warning detection of corrosion- related symptoms in hidden locations of aircraft structures. The SAFE incorporates an in situ measurement approach that measures and autonomously records several environmental conditions (i.e., pH, temperature, chloride, free potential, time-of-wetness) within a Hi-Lok aircraft fastener that could cause corrosion to occur. The SAFE system integrates a miniature electrochemical microsensor array and a time-of- wetness sensor with an ultra-low-power 8-bit microcontroller and 5-Mbyte solid-state FLASH archival memory to measure the evidence of active corrosion. A summary of the technical approach, system design definition, software architecture, and future field test plans will be presented.

Initial experience with percutaneous endoscopic gastrostomy with T-fastener fixation in pediatric patients

Science.gov (United States)

Kvello, Morten; Knatten, Charlotte Kristensen; Perminow, Gøri; Skari, Hans; Engebretsen, Anders; Schistad, Ole; Emblem, Ragnhild; Bjørnland, Kristin

2018-01-01

Background and study aims  Insertion of a percutaneous endoscopic gastrostomy (PEG) with push-through technique and T-fastener fixation (PEG-T) has recently been introduced in pediatric patients. The T-fasteners allow a primary insertion of a balloon gastrostomy. Due to limited data on the results of this technique in children, we have investigated peri- and postoperative outcomes after implementation of PEG-T in our department. Patients and methods  This retrospective chart review included all patients below 18 years who underwent PEG-T placement from 2010 to 2014. Main outcomes were 30-day postoperative complications and late gastrostomy-related complications. Results  In total, 87 patients were included, and median follow-up time was 2.4 years (1 month – 4.9 years). Median age and weight at PEG-T insertion were 1.9 years (9.4 months – 16.4 years) and 10.4 kg (5.4 – 33.0 kg), respectively. Median operation time was 28 minutes (10 – 65 minutes), and 6 surgeons and 3 endoscopists performed the procedures. During the first 30 days, 54 complications occurred in 41 patients (47 %). Most common were peristomal infections treated with either local antibiotics in 11 patients (13 %) or systemic antibiotics in 11 other patients (13 %). 9 patients (10 %) experienced tube dislodgment. Late gastrostomy-related complications occurred in 33 patients (38 %). The T-fasteners caused early and late complications in 9 (10 %) and 11 patients (13 %), respectively. Of these, 4 patients (5 %) had subcutaneously migrated T-fasteners which were removed under general anesthesia. Conclusion  We found a high rate of complications after PEG-T. In particular, problems with the T-fasteners and tube dislodgment occurred frequently after PEG-T insertion. PMID:29399615

Experimental testing and theoretical prediction of traditional dowel-type connections in tension parallel to grain

Czech Academy of Sciences Publication Activity Database

Milch, J.; Tippner, J.; Brabec, M.; Sebera, V.; Kunecký, Jiří; Kloiber, Michal; Hasníková, Hana

2017-01-01

Roč. 152, December (2017), s. 180-187 ISSN 0141-0296 R&D Projects: GA MK(CZ) DG16P02M026 Keywords : digital image correlation * dowel-type joint * European yield model * load-carrying capacity * single-shear * stiffness Subject RIV: JN - Civil Engineering OBOR OECD: Construction engineering , Municipal and structural engineering Impact factor: 2.258, year: 2016 http://www.sciencedirect.com/science/ article /pii/S0141029616311324?via%3Dihub

Instantaneous mechanical fastening of quasi-isotropic CFRP laminates by a self-piercing rivet

OpenAIRE

上田, 政人; 三宅, 崇太郎; 長谷川, 寛幸; 平野, 義鎭; Ueda, Masahito; Miyake, Sotaro; Hasegawa, Hiroyuki; Hirano, Yoshiyasu

2012-01-01

A modified self-piercing rivet (SPR) has been proposed to mechanically fasten CFRP laminates. The modified SPR consists of a rivet body and two flat washers. The two flat washers were used to suppress delamination in the CFRP laminates at the point of piercing. The advantages of the modified SPR for fastening CFRP laminates are instantaneous process time and low cost. Any pretreatments such as surface treatments or hole drilling are not required. In this study, the viability of the modified S...

Detection of fastener loosening in simple lap joint based on ultrasonic wavefield imaging

Science.gov (United States)

Gooda Sahib, M. I.; Leong, S. J.; Chia, C. C.; Mustapha, F.

2017-12-01

Joints in aero-mechanical structures are critical elements that ensure the structural integrity but they are prone to damages. Inspection of such joints that have no prior baseline data is really challenging but it can be possibly done using the Ultrasonic Propagation Imager (UPI). The feasibility of applying UPI for detection of loosened fastener is investigated in this study. A simple lap joint specimen made by connecting two pieces of 2.5mm thick SAE304 stainless steel plates using five M6 screws and nuts has been used in this study. All fasteners are tightened to 10Nm but one of them is completely loosened to simulate the damage. The wavefield data is processed into ultrasonic wavefield propagation video and a series of spectral amplitude images. The spectral images showed noticeable amplitude difference at the loosened fastener, hence confirmed the feasibility of using UPI for structural joints inspection. A simple contrast maximization method is also introduced to improve the result.

Nonlinear Coupled Dynamics of a Rod Fastening Rotor under Rub-Impact and Initial Permanent Deflection

Directory of Open Access Journals (Sweden)

Liang Hu

2016-10-01

Full Text Available A nonlinear coupled dynamic model of a rod fastening rotor under rub-impact and initial permanent deflection was developed in this paper. The governing motion equation was derived by the D’Alembert principle considering the contact characteristic between disks, nonlinear oil-film force, rub-impact force, unbalance mass, etc. The contact effects between disks was modeled as a flexural spring with cubical nonlinear stiffness. The coupled nonlinear dynamic phenomena of the rub-impact rod fastening rotor bearing system with initial permanent deflection were investigated by the fourth-order Runge-Kutta method. Bifurcation diagram, vibration waveform, frequency spectrum, shaft orbit and Poincaré map are used to illustrate the rich diversity of the system response with complicated dynamics. The studies indicate that the coupled dynamic responses of the rod fastening rotor bearing system under rub-impact and initial permanent deflection exhibit a rich nonlinear dynamic diversity, synchronous periodic-1 motion, multiple periodic motion, quasi-periodic motion and chaotic motion can be observed under certain conditions. Larger radial stiffness of the stator will simplify the system motion and make the oil whirl weaker or even disappear at a certain rotating speed. With the increase of initial permanent deflection length, the instability speed of the system gradually rises, and the chaotic motion region gets smaller and smaller. The corresponding results can provide guidance for the fault diagnosis of a rub-impact rod fastening rotor with initial permanent deflection and contribute to the further understanding of the nonlinear dynamic characteristics of the rod fastening rotor bearing system.

Performance of Rail Fastening Systems on an Open-Deck Bridge

Science.gov (United States)

2018-02-01

Transportation Technology Center, Inc. (TTCI) monitored the performance of rail fasteners on an open-deck bridge and its approaches, located at Norfolk Southern Corporations (NS's) eastern mega site. The project was co-sponsored by the Federal Rai...

Deep Defect Detection within Thick Multilayer Aircraft Structures Containing Steel Fasteners Using a Giant-Magneto Resistive (GMR) Sensor (Preprint)

National Research Council Canada - National Science Library

Ko, Ray T; Steffes, Gary J

2007-01-01

Defect detection within thick multilayer structures containing steel fasteners is a challenging task in eddy current testing due to the magnetic permeability of the fasteners and overall thickness of the structure...

Evaluation of the seat fastening in the frame of a road bus submitted to frontal impact

Directory of Open Access Journals (Sweden)

Márcio Walber

Full Text Available The collective intercity transportation by bus is currently a mean of locomotion much sought after by people. Security in accidents is a very important factor that must be taken into account in design of bus body structure, being the evaluation of passenger safety of this type of vehicle is an important subject that should be checked, because in many accidents occur disconnection between seats and fastening members causing serious passengers injury, often fatal. This work aims at evaluation the behavior of frame fixing of seats of intercity bus bodies, submitted to the frontal impact situation in a rigid wall of 100% offset, through evaluation by finite element method (FEM. This study uses a numerical model corresponding to the body structure and chassis, developed through flexible beam elements, combining with shell elements for the structure of the seats and its fastening members, with the objective of not missing the essential aspects of the problem, allowing the solution with a reduced computational time. The numerical model of bus body and seat was impacted against a rigid wall at a speed of 8.89 m/s, being its validation according to the deceleration curve established by Regulation 80. Then it was gotten the Von Mises stress in fastening members of the seat structure in bus body. It is also presented a proposal to improve the fastening of the seat structure, comparing the results of the stress gotten in the two types fastening submitted to the frontal impact.

Discrimination between Fatigue Cracking and Mechanical Damage in Aircraft Fastener Holes by Eddy-Current Phase Rotation

Science.gov (United States)

2016-08-01

Science and Technology Organisation) EDM Electrodischarge machining FSH Full Screen Height on an eddy - current instrument IVD Ion Vapour...electromagnetic skin depth δ is 0.15 mm in the fastener holes3. 4.1 Bolt Hole Eddy Current Inspection Procedure 4.1.1 Calibration on Machined ...UNCLASSIFIED UNCLASSIFIED Discrimination between Fatigue Cracking and Mechanical Damage in Aircraft Fastener Holes by Eddy - Current Phase

Test results of smart aircraft fastener for KC-135 structural integrity

Science.gov (United States)

Schoess, Jeffrey N.; Seifert, Greg

1998-07-01

Hidden and inaccessible corrosion in aircraft structures is the number one logistics problem for the US Air Force, with an estimated maintenance cost in excess of $LR 1.0B per year in 1990-equivalent dollars. The Smart Aircraft Fastener Evaluation (SAFE) system was developed to provide early warning detection of corrosion-related symptoms in hidden locations of aircraft structures. The SAFE system incorporates an in situ measurement approach that measures and autonomously records several environmental conditions within a Hi-Lok aircraft fastener that could cause corrosion. The SAFE system integrates a miniature electrochemical microsensor array and a time-of-wetness sensor with an ultra low power 8-bit microcontroller and 4- Mbyte solid-state FLASH archival memory to measure evidence of active corrosion. A summary of the technical approach and a detailed analysis of the KC-135 lap joint test coupon results are presented.

Mechanical fasteners used in historical Siberian shipbuilding: perspectives for metallurgical analysis

Science.gov (United States)

Goncharov, A. E.; Mednikov, D. M.; Karelin, N. M.; Nasyrov, I. R.

2017-10-01

Recent discoveries of shipwrecked vessels in the northern reaches of the river Yenisei led to a number of questions concerning the history of shipbuilding in Siberia and the technical features of the first vessels of the industrial era to navigate the Northern Sea Route and the Yenisei. One of these questions addresses the features of mechanical fasteners used in the construction of the Siberian vessels. The answer to this question may provide information on how the first vessels, constructed in Siberia during the 1870’s, were able to sail the high seas of the Arctic Ocean and reach European ports. In this paper, we provide a description of iron mechanical fasteners obtained from one shipwrecked vessel and discuss on the perspectives of a metallurgical analysis This research has been funded by a grant of the Russian Fund of Humanities Research (Russian Fund of Fundamental Research) and the Krasnoyarsk Regional Science Fund under Grant number 16-11-24010.

Testing of Compact Bolted Fasteners with Insulation and Friction-Enhanced Shims for NCSX

International Nuclear Information System (INIS)

Dudek, L.E.; Chrzanowski, J.H.; Gettelfinger, G.; Heitzenroeder, P.; Jurczynski, S.; Viola, M.; Freudenberg, K.

2009-01-01

The fastening of the National Compact Stellarator Experiment's (NCSX) modular coils presented a number of engineering and manufacturing challenges due to the high magnetic forces, need to control induced currents, tight tolerances and restrictive space envelope. A fastening method using high strength studs, jack nuts, insulating spacers, bushings and alumina coated shims was developed which met the requirements. A test program was conducted to verify the design. The tests included measurements of flatness of the spacers, determination of contact area, torque vs. tension of the studs and jack nuts, friction coefficient tests on the alumina and G-10 insulators, electrical tests, and tension relaxation tests due to temperature excursions from room temperature to liquid nitrogen temperatures. This paper will describe the design and the results of the test program.

Exposure testing of fasteners in preservative treated wood: Gravimetric corrosion rates and corrosion product analyses

Energy Technology Data Exchange (ETDEWEB)

Zelinka, Samuel L., E-mail: szelinka@fs.fed.u [USDA Forest Products Laboratory, One Gifford Pinchot Drive, Madison, WI 53726 (United States); Sichel, Rebecca J. [College of Engineering, University of Wisconsin, Madison, WI 53706 (United States); Stone, Donald S. [Department of Materials Science and Engineering, College of Engineering, University of Wisconsin, Madison, WI 53706 (United States)

2010-12-15

Research highlights: {yields} The composition of the corrosion products was similar for the nail head and shank. {yields} Reduced copper was not detected on any of the fasteners. {yields} Measured corrosion rates were between 1 and 35 {mu}m year{sup -1}. - Abstract: Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27 {sup o}C at 100% relative humidity for 1 year. The corrosion rate was determined gravimetrically and the corrosion products were analyzed with scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. Although the accepted mechanism of corrosion in treated wood involves the reduction of cupric ions from the wood preservative, no reduced copper was found on the corrosion surfaces. The galvanized corrosion products contained sulfates, whereas the steel corrosion products consisted of iron oxides and hydroxides. The possible implications and limitations of this research on fasteners used in building applications are discussed.

Velcro-like fasteners based on NiTi micro-hook arrays

Czech Academy of Sciences Publication Activity Database

Vokoun, David; Sedlák, Petr; Frost, Miroslav; Pilch, Jan; Majtás, Dušan; Šittner, Petr

2011-01-01

Roč. 20, č. 8 (2011), 085027/1-085027/13 ISSN 0964-1726 R&D Projects: GA ČR GAP108/10/1296; GA ČR GA106/09/1573 Institutional research plan: CEZ:AV0Z10100520; CEZ:AV0Z20760514 Keywords : Nitinol * martensitic transformation * Finite Element Method * Velcro-like fastener Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.089, year: 2011

Comparison of the corrosion of fasteners embedded in wood measured in outdoor exposure with the predictions from a combined hygrothermal-corrosion model

Science.gov (United States)

Samuel L. Zelinka; Samuel V. Glass; Charles R. Boardman; Dominique Derome

2016-01-01

This paper examines the accuracy of a recently developed hygrothermal-corrosion model which predictsthe corrosion of fasteners embedded in wood by comparing the results of the model to a one year fieldtest. Steel and galvanized steel fasteners were embedded into untreated and preservative treated woodand exposed outdoors while weather data were collected. Qualitatively...

Cross-linkable liposomes stabilize a magnetic resonance contrast-enhancing polymeric fastener.

Science.gov (United States)

Smith, Cartney E; Kong, Hyunjoon

2014-04-08

Liposomes are commonly used to deliver drugs and contrast agents to their target site in a controlled manner. One of the greatest obstacles in the performance of such delivery vehicles is their stability in the presence of serum. Here, we demonstrate a method to stabilize a class of liposomes that load gadolinium, a magnetic resonance (MR) contrast agent, as a model cargo on their surfaces. We hypothesized that the sequential adsorption of a gadolinium-binding chitosan fastener on the liposome surface followed by covalent cross-linking of the lipid bilayer would provide enhanced stability and improved MR signal in the presence of human serum. To investigate this hypothesis, liposomes composed of diyne-containing lipids were assembled and functionalized via chitosan conjugated with a hydrophobic anchor and diethylenetriaminepentaacetic acid (DTPA). This postadsorption cross-linking strategy served to stabilize the thermodynamically favorable association between liposome and polymeric fastener. Furthermore, the chitosan-coated, cross-linked liposomes proved more effective as delivery vehicles of gadolinium than uncross-linked liposomes due to the reduced liposome degradation and chitosan desorption. Overall, this study demonstrates a useful method to stabilize a broad class of particles used for systemic delivery of various molecular payloads.

Spontaneità ed esperienza. Hegel, McDowell e la radicalizzazione di Kant

Directory of Open Access Journals (Sweden)

Danilo Manca

2017-02-01

Full Text Available What are the different kinds of role played by receptivity and spontaneity in the natural experience? This question will be the clue of the essay. To answer, I will take into account some remarks raised by McDowell in Mind and World. After having shown why spontaneity should be considered as drawn into operation in experience, I will ask where the unconscious activity of conceptual capacities could be grasped. Referring on Hegels Faith and Knowledge, as first step, I will focus on the idea that the blind synthesis of imagination could be identified with the hidden work of pure reason. Consecutively, as second step, by considering what Hegel said in the Phenomenology of Spirit chapter on Sense-certainty and in the Second Preface to Science of Logic, I will delve into Hegels idea that reasons instinct is operative within natural language. My aim is to understand in what a Hegelian radicalization of Kant could consist.

The effect of moisture content on the corrosion of fasteners embedded in wood subjected to alkaline copper quaternary treatment

International Nuclear Information System (INIS)

Zelinka, Samuel L.; Glass, Samuel V.; Derome, Dominique

2014-01-01

Highlights: • We examine the dependence of metal corrosion on wood moisture content. • Corrosion of steel and galvanized steel in treated wood were measured. • Corrosion products were analyzed across moisture contents using X-ray diffraction. • The corrosion rate has a sigmoidal dependence on moisture content. • The data herein can be used to improve combined hygrothermal–corrosion models. - Abstract: This paper characterizes the corrosion rate of embedded fasteners as a function of wood moisture content using gravimetric and electrochemical measurements. The results indicated that the corrosion rate increased with moisture content before reaching a plateau. The phases present in the corrosion products, as analyzed using X-ray diffraction, are generally consistent with previous work. Uniform corrosion was observed for all fasteners and all conditions except steel fasteners embedded in water-saturated wood. Data of dependence of corrosion rate on moisture content, presented herein, are necessary to ensure the accuracy of combined hygrothermal/corrosion models used to predict durability of wood structures

"Service Recovery: The Effects of Complaint Handling on Post-complaint Relationship Intention and Customer Switching Behaviour in the Taiwan Fastener Industry"

OpenAIRE

Hwang, Jui-Chin

2005-01-01

Abstract In recent decades, many industries have started to realize the importance of relationship marketing and effective complaint handling as part of their customer retention strategies. This includes the traditional Taiwan fastener industry, which used to be considered as more technically focused rather than service-oriented. One of the main reasons for this industry to move toward a service orientation is that Taiwanese fastener trading companies have become highly customer-focused, ...

Experimental Research on the Elastic Deformation Mode of S235JR Rolled Steel Fastened between the Centers of a Universal Lathe

Science.gov (United States)

Tabacaru, LL; Axinte, E.; Musca, G.

2016-11-01

Elastic deformations of the technological system occur during the mechanical treatment of a blank, regardless of the manner in which it is fastened. The elastic deformation of the blank is significant especially when machining shaft-like parts. The purpose of our research is to compare the mathematical model of blank deformation to the experimental model when the blank, which is a part belonging to the shaft class, is fastened between centers.

Comparison study of multistep forging and injection forging of automobile fasteners

OpenAIRE

Chen Senyong; Qin Yi

2015-01-01

In order to improve production efficiency, injection forging as a feasible approach was introduced to automobile fasteners production. In the study reported in this paper, two forging approaches, traditional multistep forging and injection forging, were analysed by using a finite element method. Using ABAQUS and DEFORM, some significant factors, namely, forging force, energy consumption, component accuracy and stress distribution in the die, were compared to explore the potential and challeng...

Commercialization of a high energy neutral beam ion source. Final report

International Nuclear Information System (INIS)

1979-01-01

This final report summarizes the effort and presents the results of a Phase II fabrication effort to build an industrial prototype of the LBL developed high energy neutral beam source. The effort was primarily concentrated on incorporating hard vacuum dielectric seals and a ceramic high voltage accelerator insulator. Several other design changes were incorporated for cost, reliability or life improvements to include: (1) accelerator grid locating dowel pins to aid final alignment, (2) plasma source to accelerator captive fasteners to aid filament replacement during source maintenance, (3) molybdenum cooling tubes on all accelerator grids, (4) additional fasteners in the plasma generator to facilitate hard seals, (5) modified suppressor grid rails and holders to simplify final grid alignment, (6) adjusting screws on exit grid rail holders to simplify final grid alignment, (7) addition of adjusting screws to the grid end pieces to simplify alignment, and (8) addition of accelerator hat shims to allow two different grid positioning locations

Commercialization of a high energy neutral beam ion source. Final report

Energy Technology Data Exchange (ETDEWEB)

1979-12-21

This final report summarizes the effort and presents the results of a Phase II fabrication effort to build an industrial prototype of the LBL developed high energy neutral beam source. The effort was primarily concentrated on incorporating hard vacuum dielectric seals and a ceramic high voltage accelerator insulator. Several other design changes were incorporated for cost, reliability or life improvements to include: (1) accelerator grid locating dowel pins to aid final alignment, (2) plasma source to accelerator captive fasteners to aid filament replacement during source maintenance, (3) molybdenum cooling tubes on all accelerator grids, (4) additional fasteners in the plasma generator to facilitate hard seals, (5) modified suppressor grid rails and holders to simplify final grid alignment, (6) adjusting screws on exit grid rail holders to simplify final grid alignment, (7) addition of adjusting screws to the grid end pieces to simplify alignment, and (8) addition of accelerator hat shims to allow two different grid positioning locations.

IMPLEMENTATION OF THE LEAN-KAIZEN APPROACH IN FASTENER INDUSTRIES USING THE DATA ENVELOPMENT ANALYSIS

Directory of Open Access Journals (Sweden)

Sunil Kumar

2017-04-01

Full Text Available This research paper is an attempt to improve the quality system of ten small scale fastener manufacturing industries through the implementation of the Lean-Kaizen approach using the Data Envelopment Analysis (DEA Charnes Cooper & Rhodes (CCR model with constant returns to scale (CRS. Output maximization is taken as the objective function to identify the percentage scope of improvements. The data is collected by paying personal visits to the selected industries for three inputs (manpower, maintenance, and training of employees and two outputs (quality, on-time delivery of their quality system. The DEA CCR model is applied to identify efficiency scores of the quality system by taking the most efficient industry as a benchmark for the rest of the organizations. The Lean-Kaizen approach is applied to identify waste / non-value added activities in outputs of the selected industries. Four Kaizen events are proposed to eliminate waste / non-value added activities in their quality system. The data collected after the Kaizen events are further analyzed by the DEA CCR model. The improvements in efficiency scores of the selected industries are presented as findings in this research paper. Two fastener industries became 100% efficient while the rest of the organizations reported 8% to 49% improvements in their efficiency scores of the quality system. The conclusions are made as the Lean-Kaizen using DEA is found to be an effective approach to improve the quality system of fastener industries. This study will be beneficial for researchers, practitioners and academicians for tackling the inefficiencies in the organization.

Automatic Defect Detection of Fasteners on the Catenary Support Device Using Deep Convolutional Neural Network

NARCIS (Netherlands)

Chen, Junwen; Liu, Zhigang; Wang, H.; Nunez Vicencio, Alfredo; Han, Zhiwei

2018-01-01

The excitation and vibration triggered by the long-term operation of railway vehicles inevitably result in defective states of catenary support devices. With the massive construction of high-speed electrified railways, automatic defect detection of diverse and plentiful fasteners on the catenary

Advanced Modelling of Trusses with Punched Metal Plate Fasteners

DEFF Research Database (Denmark)

Ellegaard, Peter; Nielsen, Jacob

Most of the finite element programs for design of timber trusses with punched metal fasteners are based on models using beam and fictitious elements. Different models have been used for different types of joints. Common problems for all the models are how to calculate the forces in the nail groups...... and the plates and furthermore, how big 'the deformations in the joints are. By developing an advanced model that includes all parts of the joint, i.e. plate, nail groups and contact it is possible to give a better description of the joint. An advanced model with these properties is presented. The advanced model...

Restoration of an intruded maxillary central incisor with a uniquely designed dowel and core restoration: a case report.

Science.gov (United States)

Polat, Zelal Seyfioğlu; Tacir, Ibrahim Halil

2007-01-01

This article describes the restoration of an intruded root using a custom-made metal dowel and metal-ceramic veneer core restoration. The treatment plan for this patient consisted of restoring the missing esthetics and eliminating psychological trauma by utilizing the root of the intruded maxillary left central incisor to replace both missing central incisor crowns. This treatment will preserve space and bone until the patient is old enough for another prosthodontic restoration to be considered. As the lost fragments were not recovered, we considered this restoration of the intruded root to be the best therapeutic option, considering the effect on the patient's psyche. The patient was satisfied with the final result.

An Integrated Approach to Assess Exposure and Health-Risk from Polycyclic Aromatic Hydrocarbons (PAHs in a Fastener Manufacturing Industry

Directory of Open Access Journals (Sweden)

Hsin-I Hsu

2014-09-01

Full Text Available An integrated approach was developed to assess exposure and health-risk from polycyclic aromatic hydrocarbons (PAHs contained in oil mists in a fastener manufacturing industry. One previously developed model and one new model were adopted for predicting oil mist exposure concentrations emitted from metal work fluid (MWF and PAHs contained in MWF by using the fastener production rate (Pr and cumulative fastener production rate (CPr as predictors, respectively. By applying the annual Pr and CPr records to the above two models, long-term workplace PAH exposure concentrations were predicted. In addition, true exposure data was also collected from the field. The predicted and measured concentrations respectively served as the prior and likelihood distributions in the Bayesian decision analysis (BDA, and the resultant posterior distributions were used to determine the long-term exposure and health-risks posed on workers. Results show that long term exposures to PAHs would result in a 3.1%, 96.7%, and 73.4% chance of exceeding the PEL-TWA (0.2 mg/m3, action level (0.1 mg/m3, and acceptable health risk (10−3, respectively. In conclusion, preventive measures should be taken immediately to reduce workers’ PAH exposures.

Smart aircraft fastener evaluation (SAFE) system: a condition-based corrosion detection system for aging aircraft

Science.gov (United States)

Schoess, Jeffrey N.; Seifert, Greg; Paul, Clare A.

1996-05-01

The smart aircraft fastener evaluation (SAFE) system is an advanced structural health monitoring effort to detect and characterize corrosion in hidden and inaccessible locations of aircraft structures. Hidden corrosion is the number one logistics problem for the U.S. Air Force, with an estimated maintenance cost of $700M per year in 1990 dollars. The SAFE system incorporates a solid-state electrochemical microsensor and smart sensor electronics in the body of a Hi-Lok aircraft fastener to process and autonomously report corrosion status to aircraft maintenance personnel. The long-term payoff for using SAFE technology will be in predictive maintenance for aging aircraft and rotorcraft systems, fugitive emissions applications such as control valves, chemical pipeline vessels, and industrial boilers. Predictive maintenance capability, service, and repair will replace the current practice of scheduled maintenance to substantially reduce operational costs. A summary of the SAFE concept, laboratory test results, and future field test plans is presented.

A real-time visual inspection method of fastening bolts in freight car operation

Science.gov (United States)

Nan, Guo; Yao, JunEn

2015-10-01

A real-time inspection of the key components is necessary for ensuring safe operation of freight car. While traditional inspection depends on the trained human inspectors, which is time-consuming and lower efficient. With the development of machine vision, vision-based inspection methods get more railway on-spot applications. The cross rod end fastening bolts are important components on both sides of the train body that fixing locking plates together with the freight car main structure. In our experiment, we get the images containing fastening bolt components, and accurately locate the locking plate position using a linear Support Vector Machine (SVM) locating model trained with Histograms of Oriented Gradients (HOG) features. Then we extract the straight line segment using the Line Segment Detector (LSD) and encoding them in a range, which constitute a straight line segment dataset. Lastly we determine the locking plate's working state by the linear pattern. The experiment result shows that the localization accurate rate is over 99%, the fault detection rate is over 95%, and the module implementation time is 2f/s. The overall performance can completely meet the practical railway safety assurance application.

Estimation for bolt fastening conditions of thin aluminum structure using PZT sensors

International Nuclear Information System (INIS)

Hong, Yong; Han, Byeong Hee; Kim, Byung Jin; Hong, Dong Pyo; Kim, Young Moon

2007-01-01

This work presents a study on PZT impedance-based method, it is one of the NDT(Non-Destructive Technique). We study about assessment of the square-structure health condition by impedance-based technique using PZT patches, associated with longitudinal wave propagation. Health conditions of the square-structure controlled by bolt fastening condition is adjusted by torque wrench. In order to estimate the damage condition numerically, we suggest the evaluation method of impedance peak frequency shift

Decarburisation Effect on Hardened Strip Steel Fastening Components

Directory of Open Access Journals (Sweden)

Karli JAASON

2016-05-01

Full Text Available Heat treatment is widely used for high reliability fastening components such as buckles and brackets. The current study focuses on mass production of safety components which are fineblanked from sheet metal, austempered and chromium electroplated. Electroplating together with stamping defects may lead to unexpected brittle failure of the component. It is widely known that during austenitisation, decarburisation could avoid brittle failure and, therefore, slight decarburisation is recommended. There is little information how much mass production is influenced by decarburisation and where the limits are. The current study has two goals. The first one focuses on the extent of decarburisation effect on the part properties, and the second aims to find the optimum furnace setting for the product type used in the study. Also, it is necessary to choose a reliable decarburisation control method for austempered components. The effect on material grades was analyzed by using three steel alloys with carbon content of 0.37 wt.%, 0.47 wt.% and 0.62 wt.%. The specimens were austempered to hardness 45 – 51 HRC under endothermic protective atmosphere. To gain different decarburisation levels, two gas set-ups were used. Infrared gas analyzer was used to measure CO and CO2 content in the furnace gas. Three characteristics of the specimens were evaluated: hardness, rupture strength and brittleness. The depth of the decarburisation was determined by three different approaches according to standard EN ISO 3887. Based on the results, the spectrographic method is the most reliable for determining the depth of decarburisation. This study reveals that higher surface decarburisation has a positive effect on the ductility and no effect on the rupture strength of the component. The material with carbon content of 0.62 wt.% is the most sensitive to decarburisation. During mass production, the inaccuracy of hardness measuring raises which results in the inaccuracy of

From laboratory corrosion tests to a corrosion lifetime for wood fasteners : progress and challenges

Science.gov (United States)

Samuel L. Zelinka; Dominique Derome; Samuel V. Glass

2010-01-01

Determining a “corrosion-lifetime” for fasteners embedded in wood treated with recently adopted preservative systems depends upon successfully relating results of laboratory tests to in-service conditions. In contrast to laboratory tests where metal is embedded in wood at constant temperature and moisture content, the in-service temperature and moisture content of wood...

Influence of panel fastening on the acoustic performance of light-weight building elements: Study by sound transmission and laser scanning vibrometry

Science.gov (United States)

Roozen, N. B.; Muellner, H.; Labelle, L.; Rychtáriková, M.; Glorieux, C.

2015-06-01

Structural details and workmanship can cause considerable differences in sound insulation properties of timber frame partitions. In this study, the influence of panel fastening is investigated experimentally by means of standardized sound reduction index measurements, supported by detailed scanning laser Doppler vibrometry. In particular the effect of the number of screws used to fasten the panels to the studs, and the tightness of the screws, is studied using seven different configurations of lightweight timber frame building elements. In the frequency range from 300 to 4000 Hz, differences in the weighted sound reduction index RW as large as 10 dB were measured, suggesting that the method of fastening can have a large impact on the acoustic performance of building elements. Using the measured vibrational responses of the element, its acoustic radiation efficiency was computed numerically by means of a Rayleigh integral. The increased radiation efficiency partly explains the reduced sound reduction index. Loosening the screws, or reducing the number of screws, lowers the radiation efficiency, and significantly increases the sound reduction index of the partition.

Comprehensive and Highly Accurate Measurements of Crane Runways, Profiles and Fastenings.

Science.gov (United States)

Dennig, Dirk; Bureick, Johannes; Link, Johannes; Diener, Dmitri; Hesse, Christian; Neumann, Ingo

2017-05-13

The process of surveying crane runways has been continually refined due to the competitive situation, modern surveying instruments, additional sensors, accessories and evaluation procedures. Guidelines, such as the International Organization for Standardization (ISO) 12488-1, define target values that must be determined by survey. For a crane runway these are for example the span, the position and height of the rails. The process has to be objective and reproducible. However, common processes of surveying crane runways do not meet these requirements sufficiently. The evaluation of the protocols, ideally by an expert, requires many years of experience. Additionally, the recording of crucial parameters, e.g., the wear of the rail, or the condition of the rail fastening and rail joints, is not regulated and for that reason are often not considered during the measurement. To solve this deficit the Advanced Rail Track Inspection System (ARTIS) was developed. ARTIS is used to measure the 3D position of crane rails, the cross-section of the crane rails, joints and, for the first time, the (crane-rail) fastenings. The system consists of a monitoring vehicle and an external tracking sensor. It makes kinematic observations with the tracking sensor from outside the rail run, e.g., the floor of an overhead crane runway, possible. In this paper we present stages of the development process of ARTIS, new target values, calibration of sensors and results of a test measurement.

Tempering of martensitic steel for fasteners : Effects of micro-alloying on microstructure and mechanical property evolution

NARCIS (Netherlands)

Öhlund, C.E.I.C.

2015-01-01

The research presented in this thesis aims to deepen our understanding of the effect of micro-alloying on the microstructure and mechanical property evolution during tempering of martensitic steel for fasteners. The ongoing trend of engine down-sizing has led to the need for stronger and more

Rapid Strengthening of Full-Sized Concrete Beams with Powder-Actuated fastening Systems and Fiber-Reinforced Polymer (FRP) Composite Materials

National Research Council Canada - National Science Library

Bank, Lawrence

2002-01-01

A research study was conducted to determine if the method of retrofitting reinforced concrete beams with powder-actuated fasteners and composite materials was applicable to full-scale flexural members...

A polymeric fastener can easily functionalize liposome surfaces with gadolinium for enhanced magnetic resonance imaging.

Science.gov (United States)

Smith, Cartney E; Shkumatov, Artem; Withers, Sarah G; Yang, Binxia; Glockner, James F; Misra, Sanjay; Roy, Edward J; Wong, Chun-Ho; Zimmerman, Steven C; Kong, Hyunjoon

2013-11-26

Common methods of loading magnetic resonance imaging (MRI) contrast agents into nanoparticles often suffer from challenges related to particle formation, complex chemical modification/purification steps, and reduced contrast efficiency. This study presents a simple, yet advanced process to address these issues by loading gadolinium, an MRI contrast agent, exclusively on a liposome surface using a polymeric fastener. The fastener, so named for its ability to physically link the two functional components together, consisted of chitosan substituted with diethylenetriaminepentaacetic acid (DTPA) to chelate gadolinium, as well as octadecyl chains to stabilize the modified chitosan on the liposome surface. The assembly strategy, mimicking the mechanisms by which viruses and proteins naturally anchor to a cell, provided greater T1 relaxivity than liposomes loaded with gadolinium in both the interior and outer leaflet. Gadolinium-coated liposomes were ultimately evaluated in vivo using murine ischemia models to highlight the diagnostic capability of the system. Taken together, this process decouples particle assembly and functionalization and, therefore, has considerable potential to enhance imaging quality while alleviating many of the difficulties associated with multifunctional particle fabrication.

Temporary percutaneous T-fastener gastropexy and continuous decompressive gastrostomy in dogs with experimentally induced gastric dilatation.

Science.gov (United States)

Fox-Alvarez, W Alexander; Case, J Brad; Cooke, Kirsten L; Garcia-Pereira, Fernando L; Buckley, Gareth J; Monnet, Eric; Toskich, Beau B

2016-07-01

OBJECTIVE To evaluate a percutaneous, continuous gastric decompression technique for dogs involving a temporary T-fastener gastropexy and self-retaining decompression catheter. ANIMALS 6 healthy male large-breed dogs. PROCEDURES Dogs were anesthetized and positioned in dorsal recumbency with slight left-lateral obliquity. The gastric lumen was insufflated endoscopically until tympany was evident. Three T-fasteners were placed percutaneously into the gastric lumen via the right lateral aspect of the abdomen, caudal to the 13th rib and lateral to the rectus abdominis muscle. Through the center of the T-fasteners, a 5F locking pigtail catheter was inserted into the gastric lumen and attached to a device measuring gas outflow and intragastric pressure. The stomach was insufflated to 23 mm Hg, air was allowed to passively drain from the catheter until intraluminal pressure reached 5 mm Hg for 3 cycles, and the catheter was removed. Dogs were hospitalized and monitored for 72 hours. RESULTS Mean ± SD catheter placement time was 3.3 ± 0.5 minutes. Mean intervals from catheter placement to a ≥ 50% decrease in intragastric pressure and to ≤ 6 mm Hg were 2.1 ± 1.3 minutes and 8.4 ± 5.1 minutes, respectively. After catheter removal, no gas or fluid leakage at the catheter site was visible laparoscopically or endoscopically. All dogs were clinically normal 72 hours after surgery. CONCLUSIONS AND CLINICAL RELEVANCE The described technique was performed rapidly and provided continuous gastric decompression with no evidence of postoperative leakage in healthy dogs. Investigation is warranted to evaluate its effectiveness in dogs with gastric dilatation-volvulus.

Exposure testing of fasteners in preservative treated wood : gravimetric corrosion rates and corrosion product analyses

Science.gov (United States)

Samuel L. Zelinka; Rebecca J. Sichel; Donald S. Stone

2010-01-01

Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27oC at 100% relative humidity for 1 year. The...

Fiber Tracking Cylinder Nesting

International Nuclear Information System (INIS)

Stredde, H.

1999-01-01

The fiber tracker consists of 8 concentric carbon fiber cylinders of varying diameters, from 399mm to 1032.2mm and two different lengths. 1.66 and 2.52 meters. Each completed cylinder is covered over the entire o.d. with scintillating fiber ribbons with a connector on each ribbon. These ribbons are axial (parallel to the beam line) at one end and stereo (at 3 deg. to the beam line) at the other. The ribbon connectors have dowel pins which are used to match with the connectors on the wave guide ribbons. These dowel pins are also used during the nesting operation, locating and positioning measurements. The nesting operation is the insertion of one cylinder into another, aligning them with one another and fastening them together into a homogeneous assembly. For ease of assembly. the nesting operation is accomplished working from largest diameter to smallest. Although the completed assembly of all 8 cylinders glued and bolted together is very stiff. individual cylinders are relatively flexible. Therefore. during this operation, No.8 must be supported in a manner which maintains its integrity and yet allows the insertion of No.7. This is accomplished by essentially building a set of dummy end plates which replicate a No.9 cylinder. These end plates are mounted on a wheeled cart that becomes the nesting cart. Provisions for a protective cover fastened to these rings has been made and will be incorporated in finished product. These covers can be easily removed for access to No.8 and/or the connection of No.8 to No.9. Another wheeled cart, transfer cart, is used to push a completed cylinder into the cylinder(s) already mounted in the nesting cart.

Citizen-Scientist Led Quartz Vein Investigation in the McDowell Sonoran Preserve, Scottsdale, Arizona, Resulting in Significant Geologic Discoveries and a Peer-Reviewed Report Coauthored and with Maps by Citizen-Scientists.

Science.gov (United States)

Gruber, D.; Gootee, B.

2016-12-01

Citizen-scientists of the McDowell Sonoran Conservancy Field Institute originated and led this project to study milky quartz deposits. Milky quartz veins of all sizes are visible throughout the McDowell Sonoran Preserve (Scottsdale, Arizona) and are commonly found in Arizona Proterozoic rocks. No research on milky quartz has been done locally and little is known about its formation and emplacement history. Working with Brian Gootee, research geologist with the Arizona Geological Survey (AZGS), a citizen science team identified candidate study sites with large quartz veins and then conducted aerial balloon photography followed by geologic mapping, basic data collection, photo-documentation, and sampling from two sites. Samples were analyzed with a UV lamp, Geiger counter, and x-ray fluorescence spectrometer. Petroscopic analysis and interpretation of the samples were done by Gootee. Daniel Gruber, the citizen-science project leader, and Gootee summarized methodology, sample analyses, and interpretation in a report including detailed geologic maps. Analysis of samples from one site provided evidence of several events of Proterozoic quartz formation. The other site hosted pegmatite, cumulates, graphic granite and orbicular granite in association with milky quartz, all discovered by citizen scientists. The milky quartz and surrounding pegmatites in granite at this site trace the progression of late-stage crystallization at the margin of a fractionated granite batholith, providing an exemplary opportunity for further research into batholith geochemistry and evolution. The project required 1000 hours of citizen-science time for training, field work, data organization and entry, mapping, and writing. The report by Gootee and Gruber was reviewed and published by AZGS as an Open File Report in its online document repository. The citizen scientist team leveraged the time of professional geologists to expand knowledge of an important geologic feature of the McDowell Mountains.

Corrosion fatigue of high strength fastener materials in seawater

Science.gov (United States)

Tipton, D. G.

1983-12-01

Environmental effects which significantly reduce the fatigue life of metals are discussed. Corrosion fatigue is a major concern in the engineering application of high strength fasteners in marine environments. The corrosion fatigue failure of an AISI 41L4O high strength steel blade to hub attachment bolt at the MOD-OA 200 kW wind turbine generator was investigated. The reduction of fatigue strength of AISI 41L4O in marine environments and to obtain similar corrosion fatigue data for candidate replacement materials was studied. The AISI 4140, PH 13-8Mo stainless steel, alloy 718 and alloy MP-35N were tested in axial fatigue at a frequency of 20 Hz in dry air and natural seawater. The fatigue data are fitted by regression equations to allow determination of fatigue strength for a given number of cycles to failure.

[Functional load distribution in cases of different types of removable dentures fastening].

Science.gov (United States)

Zhulev, E N; Klokov, A A

2007-01-01

Questions of studying of a biomechanics of system prosthesis - prosthetic region using of mathematical modelling are surveyed. The original way of definition of physical parameters of a mucosa of an edentulous alveolar process is offered. Modelling of a leaky adhering of prosthesis basis to a mucosa as free saddle situation shows, that a abutment teeth and an edentulous alveolar part of a jaw are in an optimum situation at sliding resilient fastening of a removable partial denture. Rigid bond in the given situation on the contrary promotes development of an overload of abutment teeth and their inclination distally.

Embodiment and Entangled Subjectivity: A Study of Robin Cook's Coma, Priscille Sibley's The Promise of Stardust and Alexander Beliaev's Professor Dowell's Head.

Science.gov (United States)

Karmakar, Manali; Parui, Avishek

2018-03-22

The essay examines Robin Cook's (1977) Coma and Priscille Sibley's (2013) The Promise of Stardust that dramatize the reified and disposable status of the brain-dead patients who are classified as nonpersons. The essay argues that the man-machine entanglement as depicted in the novels constructs a deterritorialized and entangled form of subjectivity that intervenes in the dominant biomedical understanding of personhood and agency that we notionally associate with a conscious mind. The essay concludes its arguments by discussing Alexander Beliaev's (1925) Professor Dowell's Head which depicts human subjectivity as an essentially embodied and distributive phenomenon and interrogates the Cartesian mind body dualism embedded in the dominant biomedical narratives.

Electrochemical impedance spectroscopy (EIS) as a tool for measuring corrosion of polymer-coated fasteners used in treated wood

Science.gov (United States)

Samuel L. Zelinka; Lorraine Ortiz-Candelaria; Donald S. Stone; Douglas R. Rammer

2009-01-01

Currently, many of the polymer-coated fasteners on the market are designed for improved corrosion performance in treated wood; yet, there is no way to evaluate their corrosion performance. In this study, a common technique for measuring the corrosion performance of polymer-coated metals, electrochemical impedance spectroscopy (EIS), was used to evaluate commercial...

Use of an Automated Suture Fastening Device in Minimally Invasive Aortic Valve Replacement.

Science.gov (United States)

Beute, Tyler J; Orem, Matthew D; Schiller, Timothy M; Goehler, Matthew; Parker, Jessica; Willekes, Charles L; Timek, Tomasz

2018-03-01

Minimally invasive aortic valve replacement (mAVR) is gaining clinical acceptance, however, it is associated with increased operative times due to limited surgical field and access. The Cor-Knot is an automated fastening device designed to facilitate suture fastening, but clinical data in mAVR are lacking. From May 2014 to February 2017, 92 patients underwent mAVR at our center with 39 valves secured with manually-tied (MT) sutures and 53 valves entirely secured with the Cor-Knot (CK). Pre-operative characteristics and 30-day outcomes data were extracted from our local Society of Thoracic Surgeons database and the electronic medical record. Survival data were obtained from the Michigan State Social Security Death Index. No significant difference in pre-operative characteristics were noted between the two groups. Aortic cross-clamp time (72±12 min vs 82±15 min, p=0.001) was significantly shorter with CK. There was no difference in post-operative mortality (0% vs 0%), stroke (0% vs 1.9%), atrial fibrillation (28% vs 33%), renal failure (0% vs 3.8%), or pacemaker implantation (5.1% vs 5.7%) between MT and CK. Valve function on post-operative echocardiography and 1-year patient survival were similar. In minimally invasive aortic valve replacement, the Cor-Knot device was associated with reduced aortic cross-clamp time while providing equivalent clinical outcomes. Larger studies are needed to confirm efficacy, safety, and cost-effectiveness of the Cor-Knot device in minimally invasive aortic valve surgery. Copyright © 2018 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Nanowire surface fastener fabrication on flexible substrate

Science.gov (United States)

Toku, Yuhki; Uchida, Keita; Morita, Yasuyuki; Ju, Yang

2018-07-01

The market for wearable devices has increased considerably in recent years. In response to this demand, flexible electronic circuit technology has become more important. The conventional bonding technology in electronic assembly depends on high-temperature processes such as reflow soldering, which result in undesired thermal damages and residual stress at a bonding interface. In addition, it exhibits poor compatibility with bendable or stretchable device applications. Therefore, there is an urgent requirement to attach electronic parts on printed circuit boards with good mechanical and electrical properties at room temperature. Nanowire surface fasteners (NSFs) are candidates for resolving these problems. This paper describes the fabrication of an NSF on a flexible substrate, which can be used for room temperature conductive bonding. The template method is used for preparing high-density nanowire arrays. A Cu thin film is layered on the template as the flexible substrate. After etching the template, a Cu NSF is obtained on the Cu film substrate. In addition, the electrical and mechanical properties of the Cu NSF are studied under various fabrication conditions. The Cu NSF exhibits high shear adhesion strength (∼234 N cm‑2) and low contact resistivity (2.2 × 10‑4 Ω cm2).

Development of a 3-D model for eddy current testing: application for fastened structures in aeronautics

International Nuclear Information System (INIS)

Paillard, S.

2007-12-01

One of the Eddy Current Testing issues in aeronautics is the inspection of fastened structures to detect flaws nearby rivets which can grow because of mechanical stress. EADS and the CEA LIST have started a collaborative work with the support of the Ile-de-France Region to develop a simulation tool of EC fastened structures testing, integrated to the CIVA platform, aimed at conceiving testing methods, optimizing and qualifying it. The volume integral method using the Green dyadics formalism has been chosen in order to get a fast resolution of Maxwell equations. A first milestone was to build a simulation model of multilayer structures testing, thanks to the use of the multilayer Green dyads. Because of the rivet volume, 60 times bigger than the one of a typical flaw, a large number of discretization cells are needed. Therefore an iterative method has been developed in order to numerically solve large calculation zones. Finally, the flaw response simulation mostly has to cope with a scale issue between the size of the rivet and the one of the flaw, the latter being much smaller in a direction than the former. The whole model has been experimentally validated and compared to other simulation models at the important development steps: multilayer configuration, iteration resolution, and flaw signature. (author)

Finite-Element Modeling of Timber Joints with Punched Metal Plate Fasteners

DEFF Research Database (Denmark)

Ellegaard, Peter

2006-01-01

The focus of this paper is to describe the idea and the theory behind a finite-element model developed for analysis of timber trusses with punched metal plate fasteners (nail plates). The finite-element model includes the semirigid and nonlinear behavior of the joints (nonlinear nail and plate...... elements) and contact between timber beams, if any (bilinear contact elements). The timber beams have linear-elastic properties. The section forces needed for design of the joints are given directly by the finite-element model, since special elements are used to model the nail groups and the nail plate...... the behavior of the joints very well at lower load levels. At higher load levels the stiffness is overestimated due to development of cracks in the timber and the linear-elastic timber properties in the finite-element model....

Performance Characterization of Loctite (Registered Trademark) 242 and 271 Liquid Locking Compounds (LLCs) as a Secondary Locking Feature for International Space Station (ISS) Fasteners

Science.gov (United States)

Dube, Michael J.; Gamwell, Wayne R.

2011-01-01

Several International Space Station (ISS) hardware components use Loctite (and other polymer based liquid locking compounds (LLCs)) as a means of meeting the secondary (redundant) locking feature requirement for fasteners. The primary locking method is the fastener preload, with the application of the Loctite compound which when cured is intended to resist preload reduction. The reliability of these compounds has been questioned due to a number of failures during ground testing. The ISS Program Manager requested the NASA Engineering and Safety Center (NESC) to characterize and quantify sensitivities of Loctite being used as a secondary locking feature. The findings and recommendations provided in this investigation apply to the anaerobic LLCs Loctite 242 and 271. No other anaerobic LLCs were evaluated for this investigation. This document contains the findings and recommendations of the NESC investigation

Energy Neutral Wireless Bolt for Safety Critical Fastening.

Science.gov (United States)

Seyoum, Biruk B; Rossi, Maurizio; Brunelli, Davide

2017-09-26

Thermoelectric generators (TEGs) are now capable of powering the abundant low power electronics from very small (just a few degrees Celsius) temperature gradients. This factor along with the continuously lowering cost and size of TEGs, has contributed to the growing number of miniaturized battery-free sensor modules powered by TEGs. In this article, we present the design of an ambient-powered wireless bolt for high-end electro-mechanical systems. The bolt is equipped with a temperature sensor and a low power RF chip powered from a TEG. A DC-DC converter interfacing the TEG with the RF chip is used to step-up the low TEG voltage. The work includes the characterizations of different TEGs and DC-DC converters to determine the optimal design based on the amount of power that can be generated from a TEG under different loads and at temperature gradients typical of industrial environments. A prototype system was implemented and the power consumption of this system under different conditions was also measured. Results demonstrate that the power generated by the TEG at very low temperature gradients is sufficient to guarantee continuous wireless monitoring of the critical fasteners in critical systems such as avionics, motorsport and aerospace.

Energy Neutral Wireless Bolt for Safety Critical Fastening

Directory of Open Access Journals (Sweden)

Biruk B. Seyoum

2017-09-01

Full Text Available Thermoelectric generators (TEGs are now capable of powering the abundant low power electronics from very small (just a few degrees Celsius temperature gradients. This factor along with the continuously lowering cost and size of TEGs, has contributed to the growing number of miniaturized battery-free sensor modules powered by TEGs. In this article, we present the design of an ambient-powered wireless bolt for high-end electro-mechanical systems. The bolt is equipped with a temperature sensor and a low power RF chip powered from a TEG. A DC-DC converter interfacing the TEG with the RF chip is used to step-up the low TEG voltage. The work includes the characterizations of different TEGs and DC-DC converters to determine the optimal design based on the amount of power that can be generated from a TEG under different loads and at temperature gradients typical of industrial environments. A prototype system was implemented and the power consumption of this system under different conditions was also measured. Results demonstrate that the power generated by the TEG at very low temperature gradients is sufficient to guarantee continuous wireless monitoring of the critical fasteners in critical systems such as avionics, motorsport and aerospace.

Fastener locking device for attaching guide thimble to fuel assembly bottom nozzle

International Nuclear Information System (INIS)

Widener, W.H.

1987-01-01

This patent describes a nuclear reactor fuel assembly including an end nozzle and at least one longitudinally-extending guide thimble projecting away from the end nozzle. The end nozzle has at least one passageway defined therethrough and a ledge defined within the passageway so as to face away from the guide thimble and divide the passageway into a first portion extending from the ledge toward the guide thimble. A second portion extends from the ledge away from the guide thimble. The second passageway portion has a larger cross-sectional size than the first passageway portion, the end nozzle also having recess means defined thereon in the second portion of the passageway. The guide thimble has an end disposed adjacent to the first portion of the passageway with threaded means defined thereon and a fastener locking device

Investigation Analysis of Crack Growth Arresting with Fasteners in Hybrid Laminated Skin-Stiffener Joint

Science.gov (United States)

Jeevan Kumar, N.; Ramesh Babu, P.

2018-02-01

In recent years carbon fibre-reinforced polymers (CFRP) emerged its increasing demand in aerospace engineering. Due to their high specific strength to weight ratio, these composites offer more characteristics and considerable advantages compared to metals. Metals, unlike composites, offer plasticity effects to evade high stress concentrations during postbuckling. Under compressive load, composite structures show a wide range of damage mechanisms where a set of damage modes combined together might lead to the eventual structural collapse. Crack is one of the most critical damages in fiber composites, which are being employed in primary aircraft structures. A parametric study is conducted to investigate the arrest mechanism of the delamination or crack growth with installation of multiple fasteners when the delamination is embedded in between the skin and stiffener interface.

The Use of Explosive Forming for Fastening and Joining Structural and Pressure Components

Science.gov (United States)

Schroeder, J. W.

1985-01-01

Explosive expansion of tubes into tubesheets has been used for over 20 years in the fabrication and repair of shell and tube heat exchangers. The use of explosives to perform these expansions has offered several distinct advantages over other methods. First, the process is fast and economical and can be performed with minimal training of personnel. Secondly, explosive forming does not cause the deleterious metallurgical effects which often result from other forming operations. In addition, the process can be performed remotely without the need for sophisticated handling equipment. The expansion of tubes into tubesheets is only one of many possible fastening and joining applications for which explosive forming can be used to achieve highly successful results. The explosive forming process and where it has been used are described. In addition, some possible adaptations to other joining applications are identified and discussed.

Analysis and Experiments on Sea Load and Fastened Mechanics on Pipe Clamps

Directory of Open Access Journals (Sweden)

Wang Zhuo

2017-08-01

Full Text Available When an offshore oil field completed and put into production, new subsea pipelines and the new cable need to be established. Cable protection pipe clamp is used to fix cable protection pipe on the jacket. In order to avoid the problem of traditional steel structure clamp splice, counterpoint, fastening difficulty when installed cable protection pipe under water, reduce the risk and workload of under water, This paper develop a new type of portable connecting riser clamp -“backpack clamp” which solve the riser cable protection pipe difficult underwater installation problem. The main structure of backpack clamp used three valves type structure. The load characteristic of a clamping device was determined by the Morison equation which was a classical theory. Clamp device underwater mechanics analysis model was established. The minimum tension pre-tightening force was determined. The results show that the strength of the base meets the requirements after strength analysis with finite element analysis method, stability and strength experiments, which means the clamp based on resin matrix composite is feasible.

New Challenges to the automotive fasteners and cold formed parts in the chinese markets

Directory of Open Access Journals (Sweden)

Chen Jin Guang

2015-01-01

Full Text Available Despite of substantial cold forming related R&D, innovations and new inventions have been achieved and reported by research institutes and famous industrial organisations, many small and medium size enterprises in the third world or developing countries considering this R&D activities is too luxury. Most of the third world cold forming factories still dependent on previously successful experiences by using trial an error methods. The author does not make attempt to write a scientific research paper on metal forming processes but, instead, to report the effect, application and impact of the previous and on-going metal forming related research work to the cold forming industry in China. This paper highlights the effect of 1 efficient manufacturing practices, 2 upgrading in process technology and 3improved machines capabilities in upgrading the cold forming operation. Three real-life cold forming examples from Ritai are illustrated showing the transformation from an automotive fasteners maker into a cold formed parts manufacturer.

Microstructure and Properties of Ti-5553 Alloy for Aerospace Fasteners

Directory of Open Access Journals (Sweden)

ZHAO Qing-yun

2017-10-01

Full Text Available The effect of heat treatment on microstructure and mechanical properties of Ti-5553 alloy was investigated by scanning electron microscopy (SEM and transmission electron microscopy (TEM. The results show that when the alloy is treated in α+β phase zone, tensile strength decreases with raising solution temperature due to decreasing the content of primary α-phase and increasing the size and volume fraction of β phase. A lot of secondary α-phase precipitates from grain boundary and intragranular with β phase transformation during aging treatment. The size of secondary α-phase has significant influence on tensile strength, secondary α-phase coarsens gradually with the increase of aging temperature, resulting in the decrease of tensile strength. It is suggested that for 1240MPa aerospace fasteners the solution temperature of Ti-5553 should be under Tβ, thus adequate β phase, where a lot of secondary α phase precipitates from, is good for the required high strength. Meanwhile, a certain percentage of primary α-phase is kept for acquiring good ductility and toughness. After solution treatment at 810-820℃ for 1.5h, water quenching plus aging at 510℃ for 10h, Ti-5553 shows a better mechanical property with tensile strength 1500MPa, elongation 14.8% and reduction of cross-section area 38.6%. Lots of dimples can be found in tensile fracture after solution treatment and solution+aging treatment, which demonstrate Ti-5553 with good ductility and toughness.

An evaluation of ACI 349 code for design of the fastening system at nuclear power plant

International Nuclear Information System (INIS)

Jang, J.-B.; Suh, Y.-P.; Lee, J.-R.

2005-01-01

ACI 349 Code, revised on 2001, is only available for the anchor with diameter not exceeding 2 in. and tensile embedment not exceeding 25 in. in depth. So, ACI 349 Code can't be applied to the design of the large sized anchor with diameter exceeding 2 in. and tensile embedment exceeding 25 in. in depth which fastens the SG, RV, RCP, PZR, etc. at containment building. Therefore, an application of ACI 349 Code was investigated for the design of the small and large sized anchors under tensile load using the numerical analysis model which was developed on a basis of the various test data of cast-in-place anchor in this study. In conclusion, it is proved that ACI 349 Code is available for the design of the small and large sized cast-in-place anchor. (authors)

RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling

Directory of Open Access Journals (Sweden)

Enzo Martinelli

2014-03-01

Full Text Available The use of mechanically-fastened fiber-reinforced polymer (MF-FRP systems has recently emerged as a competitive solution for the flexural strengthening of reinforced concrete (RC beams and slabs. An overview of the experimental research has proven the effectiveness and the potentiality of the MF-FRP technique which is particularly suitable for emergency repairs or when the speed of installation and immediacy of use are imperative. A finite-element (FE model has been recently developed by the authors with the aim to simulate the behavior of RC beams strengthened in bending by MF-FRP laminates; such a model has also been validated by using a wide experimental database collected from the literature. By following the previous study, the FE model and the assembled database are considered herein with the aim of better exploring the influence of some specific aspects on the structural response of MF-FRP strengthened members, such as the bearing stress-slip relationship assumed for the FRP-concrete interface, the stress-strain law considered for reinforcing steel rebars and the cracking process in RC members resulting in the well-known tension stiffening effect. The considerations drawn from this study will be useful to researchers for the calibration of criteria and design rules for strengthening RC beams through MF-FRP laminates.

Asphalt Mixture for the First Asphalt Concrete Directly Fastened Track in Korea

Directory of Open Access Journals (Sweden)

Seong-Hyeok Lee

2015-01-01

Full Text Available The research has been initiated to develop the asphalt mixtures which are suitable for the surface of asphalt concrete directly fastened track (ADFT system and evaluate the performance of the asphalt mixture. Three aggregate gradations which are upper (finer, medium, and below (coarser. The nominal maximum aggregate size of asphalt mixture was 10 mm. Asphalt mixture design was conducted at 3 percent air voids using Marshall mix design method. To make impermeable asphalt mixture surface, the laboratory permeability test was conducted for asphalt mixtures of three different aggregate gradations using asphalt mixture permeability tester. Moisture susceptibility test was conducted based on AASHTO T 283. The stripping percentage of asphalt mixtures was measured using a digital camera and analyzed based on image analysis techniques. Based on the limited research results, the finer aggregate gradation is the most suitable for asphalt mixture for ADFT system with the high TSR value and the low stripping percentage and permeable coefficient. Flow number and beam fatigue tests for finer aggregate asphalt mixture were conducted to characterize the performance of asphalt mixtures containing two modified asphalt binders: STE-10 which is styrene-butadiene-styrene (SBS polymer and ARMA which is Crum rubber modified asphalt. The performance tests indicate that the STE-10 shows the higher rutting life and fatigue life.

Effect of Chord Splice Joints on Force Distribution and Deformations in Trusses with Punched Metal Plate Fasteners

DEFF Research Database (Denmark)

Ellegaard, Peter

2007-01-01

The span of roof trusses with punched metal plate fasteners (nail plates) makes it often necessary to use splice joints in the top and bottom chords. In the finite element models used for design of the trusses these splice joints are normally assumed to be either rotationally stiff or pinned....... Timber-to-timber contact and non-linear elastic behaviour are included in the model. Results from tests with joints under fourpoint bending are compared with predictions given by TrussLab, and a good agreement is found. Splice joints in trusses with nail plates may be assumed to be rotationally stiff...... if their deformation has no significant effect upon the distribution of member forces according to Eurocode 5. Two simple guidelines for the design and location of splice joints are given in Eurocode 5 for treating the splice joints as rotationally stiff. The reasonability of these guidelines and the influence...

Method for limiting movement of a thermal shield for a nuclear reactor, and thermal shield displacement limiter therefor

International Nuclear Information System (INIS)

Meuschke, R.E.; Boyd, C.H.

1989-01-01

This patent describes a method of limiting the movement of a thermal shield of a nuclear reactor. It comprises: machining at least four (4) pockets in upper portions of a thermal shield circumferentially about a core barrel of a nuclear reactor to receive key-wave inserts; tapping bolt holes in the pockets of the thermal shield to receive bolts; positioning key-wave inserts into the pockets of the thermal shield to be bolted in place with the bolt holes; machining dowel holes at least partially through the positioned key-way inserts and the thermal shield to receive dowel pins; positioning dowel pins in the dowel holes in the key-way insert and thermal shield to tangentially restrain movement of the thermal shield relative to the core barrel; sliding limiter keys into the key-way inserts and bolting the limiter keys to the core barrel to tangentially restrain movement of the thermal shield relative and the core barrel while allowing radial and axial movement of the thermal shield relative to the core barrel; machining dowel holes through the limiter key and at least partially through the core barrel to receive dowel pins; positioning dowel pins in the dowel holes in the limiter key and core barrel to restrain tangential movement of the thermal shield relative to the core barrel of the nuclear reactor

Evaluation of responses to IE Bulletin 82-02: degradation of threaded fasteners in reactor coolant pressure boundary of pressurized-water-reactor plants

International Nuclear Information System (INIS)

Anderson, W.; Sterner, P.

1985-05-01

IE Bulletin 82-02 was issued by the NRC on June 2, 1982, to notify licensees about incidents of severe degradation of threaded fasteners. The bulletin required appropriate action including submittal of information from pressurized water reactors having an operating license. Responses from 41 licensees included their recent experience with degradation of threaded fasteners in primary system components. Data from recent regular inspections of reactor coolant pressure boundary component connections of 6-in. size and larger are compiled for technical evaluation. Statistical analysis is used to determine significant factors related to frequency of leakage incidents in connections, occurrence of degradation of bolts and studs, and the need for bolt replacement. Factors examined include the age of the plant, types of components, use of lubricants and sealants, and differences between plants. The compiled data indicate that, on the average, 10% of the bolted connections show evidence of leaking during an 18-month period. Also, 80% of the connections that show evidence of leakage undergo some degradation of the bolting. Results of the analysis show a significant decrease in the occurrence of bolting degradation events as the age of the plant increases. The data also show that valves are less subject to bolting corrosion. A group of 5 of the 41 plants accounted for about one-half of the reported leakage and corrosion events. The common characteristic found for four of these five plants was the lubricant used. The use of nickel-graphite based lubricants appears to offer a significantly reduced incidence of leakage and corrosion, based on late corrections to the reported data. The data also permit the conclusion that the use of molybdenum-disulfide-based lubricants and graphite-based lubricants results in a significantly increased incidence of leakage and corrosion. Reporting of data on lubricants was of poor quality and detracted from the value of the bulletin responses

El triángulo de McDowell y otros recursos para trabajar la expresión escrita y los marcadores del discurso en el aula de E/LE

Directory of Open Access Journals (Sweden)

Adrián Ombuena Cabanes

2015-10-01

Full Text Available En esta comunicación se presentan un conjunto de actividades ordenadas gradualmente siguiendo el triángulo de McDowell: cada actividad se define según el grado de control del docente sobre la tarea de los alumnos. La última actividad es una actividad comunicativa de expresión escrita (EE donde se aprovechan los contenidos vistos a lo largo de la secuencia didáctica. La actividad final consiste en escribir un texto expositivo-argumentativo utilizando marcadores discursivos (MD. No todas las actividades son de EE, pero sí todas están encaminadas a preparar una buena EE (reconocer MD, localizar MD, organizar MD, planificar la EE con MD. Además, en esta secuencia se utilizan actividades de aprendizaje cooperativo (como el puzle de Aronson, cuya aplicación asegura el aprendizaje significativo. Se presenta aquí una propuesta para acercar a los alumnos de E/LE la importancia del uso de MD y de la planificación para lograr una EE satisfactoria.

Fatigue of anchors for the fastening of wind turbines to reinforced concrete foundations. Vermoeiing van ankers voor de bevestiging van windmolens aan fundaties van gewapend beton

Energy Technology Data Exchange (ETDEWEB)

Liemberg, B J; Bouwman, L P

1983-01-01

Nowadays slender and slack masts are preferred for wind turbines, fastened to a concrete foundation with anchor bolts. This concept leads to strongly fluctuating forces. Tests are described to investigate this aspect of wind turbine design. Test specimens were designed and loaded in such a way that the real situation was simulated as close as possible. They were subjected to fatigue tests and duration tests. Some important conclusions are: foot plates with two contact surfaces are significantly better than those with only one contact surface; a good filling of the seam, especially in a direct line with the mast is essential.

COMPARISON BETWEEN TEST METHODS TO DETERMINE WOOD EMBEDMENT STRENGTH PARALLEL TO THE GRAIN

Directory of Open Access Journals (Sweden)

Diego Henrique de Almeida

Full Text Available ABSTRACT This study compares the test methods according to the ABNT NBR 7190:1997, EN 383:2007, ASTM D5764:2007, EUROCODE 5:2004, NDS:2001 standards in order to provide support to establish a new test method for determining the embedment strength of wood parallel to the grain. Parallel-to-grain tests were carried out for six wood species (Schizolobium amazonicum; Pinus elliottii; Pinus oocarpa; Hymenaea spp.; Lyptus(r: hybrid Eucalyptus grandis and Eucalyptus urophylla, and Goupia glabra using four diameters (8 mm, 10 mm, 12 mm and 16 mm for the metal pin fasteners (bolts. The experimental results obtained according to the EN 383:2007 standard were closer to the specific values for the metal-dowel connections design used by ABNT NBR 7190:1997, which are considered equal compression parallel to the grain. The use of maximum embedment force or the force causing displacement of 5 mm between the bolt and the test-piece as criteria for determining embedment strength for EN 383:2007 appears to be more appropriate than the criteria used by the Brazilian and American Standards.

Development of a 3-D model for eddy current testing: application for fastened structures in aeronautics; Developpement d'un modele pour le controle non destructif par courants de Foucault de structures rivetees en aeronautique

Energy Technology Data Exchange (ETDEWEB)

Paillard, S

2007-12-15

One of the Eddy Current Testing issues in aeronautics is the inspection of fastened structures to detect flaws nearby rivets which can grow because of mechanical stress. EADS and the CEA LIST have started a collaborative work with the support of the Ile-de-France Region to develop a simulation tool of EC fastened structures testing, integrated to the CIVA platform, aimed at conceiving testing methods, optimizing and qualifying it. The volume integral method using the Green dyadics formalism has been chosen in order to get a fast resolution of Maxwell equations. A first milestone was to build a simulation model of multilayer structures testing, thanks to the use of the multilayer Green dyads. Because of the rivet volume, 60 times bigger than the one of a typical flaw, a large number of discretization cells are needed. Therefore an iterative method has been developed in order to numerically solve large calculation zones. Finally, the flaw response simulation mostly has to cope with a scale issue between the size of the rivet and the one of the flaw, the latter being much smaller in a direction than the former. The whole model has been experimentally validated and compared to other simulation models at the important development steps: multilayer configuration, iteration resolution, and flaw signature. (author)

Three Sorts of Naturalism

OpenAIRE

Fink, Hans

2006-01-01

In "Two sorts of Naturalism" John McDowell is sketching his own sort of naturalism in ethics as an alternative to "bald naturalism". In this paper I distinguish materialist, idealist and absolute conceptions of nature and of naturalism in order to provide a framework for a clearer understanding of what McDowell's own naturalism amounts to. I argue that nothing short of an absolute naturalism will do for a number of McDowell's own purposes, but that it is far from obvious that this is his posi...

EFFECTS OF EDGE COVERING ON TENSILE STRENGTH OF MDF

Directory of Open Access Journals (Sweden)

Yalçın ÖRS

1999-03-01

Full Text Available Dowels, 6, 8 and 10 mm ? diameters were bonded with PVAc adhesive on Medium Density Fiberboard (MDF. Edges were covered with 5, 8 and 12 mm beech wood materials, drilled 25 mm depth. Tensile strength measurments were made on the samples. The highest tensile strength value was given as 6 mm ? dowel and MDF covered with 8 mm thickness beech wood material (2.294 N/mm2, the lowest value was obtained with 10 mm ? dowel and with unprocessed MDF (1.314 N/mm2.

Development of Shear Connections in Steelconcrete Composite Structures

Science.gov (United States)

Biegus, Antoni; Lorenc, Wojciech

2015-03-01

Different types of shear connectors and modelling techniques are presented. Basic research conducted or presented after year 2000 is taken into consideration, following the idea of concrete dowel implemented in the form of perfobond strip at the beginning of the 1980s by F. Leonhardt. The latest research in the field of continuous shear connectors applied in bridges is highlited with special focus at the composite dowel shear connection, as it seems to be the most modern solution being strongly introduced to the industry. Final shape of composite dowel shear connection is presented.

Accelerated testing for studying pavement design and performance (FY 2001) : evaluation of the performance of permeable and semi-permeable unbound granular bases under Portland Cement Concrete Pavement (PCCP) slabs and alternate load transfer devices for

Science.gov (United States)

2003-11-01

The objectives of this research are to determine the effect of unbound drainable base types on the performance of PCCP and the efficiency of fiber-reinforced polymer (FRP) dowels, compared to epoxy coated steel dowels, when retrofitted to re-establis...

B-scan technique for localization and characterization of fatigue cracks around fastener holes in multi-layered structures

Science.gov (United States)

Hopkins, Deborah; Datuin, Marvin; Aldrin, John; Warchol, Mark; Warchol, Lyudmila; Forsyth, David

2018-04-01

The work presented here aims to develop and transition angled-beam shear-wave inspection techniques for crack localization at fastener sites in multi-layer aircraft structures. This requires moving beyond detection to achieve reliable crack location and size, thereby providing invaluable information for maintenance actions and service-life management. The technique presented is based on imaging cracks in "True" B-scans (depth view projected in the sheets along the beam path). The crack traces that contribute to localization in the True B-scans depend on small, diffracted signals from the crack edges and tips that are visible in simulations and experimental data acquired with sufficient gain. The most recent work shows that cracks rotated toward and away from the central ultrasonic beam also yield crack traces in True B-scans that allow localization in simulations, even for large obtuse angles where experimental and simulation results show very small or no indications in the C-scans. Similarly, for two sheets joined by sealant, simulations show that cracks in the second sheet can be located in True B-scans for all locations studied: cracks that intersect the front or back wall of the second sheet, as well as relatively small mid-bore cracks. These results are consistent with previous model verification and sensitivity studies that demonstrate crack localization in True B-scans for a single sheet and cracks perpendicular to the ultrasonic beam.

40 CFR 81.349 - West Virginia.

Science.gov (United States)

2010-07-01

... Marshall County Mason County McDowell County Mercer County Mineral County Mingo County Monongalia County... Jefferson County Lewis County Lincoln County Logan County Marion County Marshall County Mason County... County Mason County McDowell County Mercer County Mineral County Mingo County Monongalia County Monroe...

Modelo para avaliação econômica comparativa entre alternativas de sistemas de fixação com elementos roscados An approach model to a comparative economic assessment of alternatives for threaded fastening systems

Directory of Open Access Journals (Sweden)

João Carlos Barreto Piekarski

2009-09-01

strongly dependent on previous stages decisions, mostly those related to the product development process. Several of these decisions are influenced by the experience or personal preferences from the design team. Additionally, most products depend on the assembly processes, which can assume different configurations (e.g. permanent (riveting or non-permanent (fastening joining solutions. From the environment point of view, the reversible systems perform a fundamental role during the product development process. The choice for a fastening system occurs during the design stage. Thus, this paper aims at the development of a model that supports the decision making process when choosing reversible fastening systems, based on the economic aspects of the manufacturing/assembling process examined. The entry data and model structure are well adhered to the industrial reality, theoretical parameters, and data from the experiments. The model considers the costs factors originated from: i/ purchasing and storage; ii/ manufacturing; iii/ assembling; and iv/ maintenance; which are the main stages of a component life cycle. The set of equations that support the model is also presented. A preliminary model test illustrates its capabilities for capturing the cost differences amongst fastening systems for a specific assembly, from parameters defined at early stages of the design process.

Book Review: Commemoration as Conflict: Space, Memory and Identity in Peace Processes

DEFF Research Database (Denmark)

McQuaid, Sara Dybris

2016-01-01

Book rewiew: Commemoration as Conflict: Space, Memory and Identity in Peace Processes / Sara McDowell and Maire Braniff Palgrave Macmillan, 2014, 224pp., ISBN 978-0-230-27375-7......Book rewiew: Commemoration as Conflict: Space, Memory and Identity in Peace Processes / Sara McDowell and Maire Braniff Palgrave Macmillan, 2014, 224pp., ISBN 978-0-230-27375-7...

Nilai Kekuatan Tumpu Baut pada Empat Jenis Kayu Rakyat Indonesia

Directory of Open Access Journals (Sweden)

Sucahyo Sadiyo

2017-08-01

Full Text Available The fasteners bearing strength is one of the properties that affect reference design value (Z on dowel-type connections. In Indonesia, the value of bolt bearing strength can be determined in theory by SNI 7973 which adopt NDS standard. This study was conducted to determine the bolt bearing strength by using three bolts diameter (1/2 in, 5/8 in and 3/4 in and four Indonesian woods community species which are sengon (Paraserianthes falcataria, jabon (Anthocephalus cadamba, manii (Maesopsis eminii and nangka (Artocarpus heterophyllus compared with SNI 7973. The results showed that bolt bearing strength can be affected by density and specific gravity. Moreover, the compression strength parallel to grain can be used as a parameter to predict bolt bearing strength. The higher compression strength parallel to grain, the higher bolt bearing strength will be. The bolt bearing strength based on wood species were sengon 161 kg/cm2, jabon 151 kg/cm2, manii 243 kg/cm2 and nangka 392 kg/cm2 respectively. Bolt with 1/2 in diameter has the highest bolt bearing strength except for jabon wood. The difference of bolt bearing strength on sengon and jabon versus SNI 7973 was differ significantly by 16-27% while the bolt bearing strength on manii and nangka was not differ significantly by 2-3%.

Evolution mechanisms of MgO·Al2O3 inclusions by cerium in spring steel used in fasteners of high-speed railway

International Nuclear Information System (INIS)

Wang Lijun; Wang Qi; Chou Kuochih; Liu Yanqiang

2015-01-01

The effect of rare earth metal addition on the non-metallic inclusions in spring steel used in fastener of high speed railway was investigated by metallographic examination; SEM-EDS and component analysis, aiming at deform those harmful inclusions to improve service life of spring steel. MgO·Al 2 O 3 inclusions were found in present experimental steel, which is also confirmed by the stability diagram of MgO/MgO·Al 2 O 3 /Al 2 O 3 from thermodynamic consideration. After Ce addition, the evolution process of Al 2 O 3 ·MgO inclusions was determined through the surface and line scanning. The effects of time and Ce content on the evolution of Al 2 O 3 ·MgO inclusions were examined. It was indicated that Al 2 O 3 ·MgO inclusions were wrapped by rare earth inclusions to form a ring like shape Ce-riched band around the inclusion, which would be useful to improve fatigue and corrosion resistance of spring steel. It was found that diffusion of Ce 3+ , Al 3+ and Mg 2+ in inclusions core and intermediate layer would be the limited step during evolutions of inclusions. (author)

Experimental field study of problem-solving using tools in free-ranging capuchins (Sapajus nigritus, formerly Cebus nigritus).

Science.gov (United States)

Garber, P A; Gomes, D F; Bicca-Marques, J C

2012-04-01

Some populations of capuchins are reported to use tools to solve foraging problems in the wild. In most cases, this involves the act of pounding and digging. The use of probing tools by wild capuchins is considerably less common. Here we report on the results of an experimental field study conducted in southern Brazil designed to examine the ability of wild black-horned capuchins (Sapajus nigritus) to use a wooden dowel as a lever or a probe to obtain an embedded food reward. A group of eight capuchins was presented with two experimental platforms, each housing a clear Plexiglas box containing two bananas on a shelf and four inserted dowels. Depending on the conditions of the experiment, the capuchins were required either to pull (Condition I) or push (Conditions II and III) the dowels, in order to dislodge the food reward from the shelf so that it could be manually retrieved. In Condition I, four individuals spontaneously solved the foraging problem by pulling the dowels in 25% (72/291) of visits. In Conditions II and III, however, no capuchin successfully pushed the dowels forward to obtain the food reward. During these latter two experimental conditions, the capuchins continued to pull the dowels (41/151 or 27% of visits), even though this behavior did not result in foraging success. The results of these field experiments are consistent with an identical study conducted on wild Cebus capucinus in Costa Rica, and suggest that when using an external object as a probe to solve a foraging problem, individual capuchins were able to rapidly learn an association between the tool and the food reward, but failed to understand exactly how the tool functioned in accomplishing the task. The results also suggest that once a capuchin learned to solve this tool-mediated foraging problem, the individual persisted in using the same solution even in the face of repeated failure (slow rate of learning extinction). © 2011 Wiley Periodicals, Inc.

Mind the gap: gender disparities still to be addressed in UK Higher Education geography

OpenAIRE

Maddrell, Avril; Strauss, Kendra; Thomas, Nicola J.; Wyse, Stephanie

2016-01-01

This paper evidences persistent gender inequalities in UK higher education (HE) geography departments. The two key sources of data used are: Higher Education Statistics Agency (HESA) data for staff and students, which affords a longitudinal response to earlier surveys by McDowell and McDowell and Peake of women in UK university geography departments, and a qualitative survey of the UK HE geography community undertaken in 2010 that sought more roundly to capture respondent reflections on their...

Apparatus For Eddy-Current Inspection Of Bolts

Science.gov (United States)

Amos, Jay M.

1994-01-01

Eddy-current apparatus for inspection of bolts, studs, and other threaded fasteners detects flaws in threads, shanks, and head fillets. With help of apparatus, technician quickly inspects fasteners of various dimensions. Accommodates fasteners with diameters from 0.190 in. to 1 in. and with lengths up to 5 in. Basic design modified to accommodate fasteners of other sizes.

Strategy-driven talent management a leadership imperative

CERN Document Server

Silzer, Rob

2009-01-01

A Publication of the Society for Industrial and Organizational Psychology Praise for Strategy-Driven Talent Management ""Silzer and Dowell''s Strategy-Driven Talent Management provides a comprehensive overview of the different elements of the best talent management processes used in organizations today. This is a valuable resource for leaders and managers, HR practitioners and anyone involved in developing leadership talent.""-Ed Lawler, Professor, School of Business, University of Southern California ""Talent is the key to successful execution of a winning business strategy. Strategy-Driven T

Co-consolidation of titanium-C/PAEK joints: an investigation into the interfacial performance governing mechanisms

NARCIS (Netherlands)

Su, Y.

2017-01-01

Fastener free metal-carbon fibre reinforced thermoplastic composite hybrid joints show a potential for application in aerospace structures. In comparison with fastened hybrid joints, fastener free hybrid joints exhibit advantages in terms of joint weight reduction and a more uniformly distributed

Anchorage in concrete construction

CERN Document Server

Eligehausen, Rolf; Silva, John F

2013-01-01

A comprehensive treatment of current fastening technology using inserts (anchor channels, headed stud), anchors (metal expansion anchor, undercut anchor, bonded anchor, concrete screw and plastic anchor) as well as power actuated fasteners in concrete. It describes in detail the fastening elements as well as their effects and load-bearing capacities in cracked and non-cracked concrete. It further focuses on corrosion behaviour, fire resistance and characteristics with earthquakes and shocks. It finishes off with the design of fastenings according to the European Technical Approval Guideline (ETAG 001), the Final Draft of the CEN Technical Specification 'Design of fastenings for use in concrete' and the American Standards ACI 318-05, Appendix D and ACI 349-01, Appendix B.

Evaluation of effective coolant flow rate in advanced design of the small scale VHTR core

International Nuclear Information System (INIS)

Fumizawa, Motoo; Suzuki, Kunihiko; Murakami, Tomoyuki.

1988-02-01

This report describes the evaluation of effective coolant flow rate in the advanced design of the small scale VHTR core. The analytical design study was carried out after the 2nd stage of detailed design in order to reduce the cost of construction. The summary of the analytical results are as follows: (1) Crossflow loss coefficient of flange type fuel block having 0.1 mm of sealing gap is about 100 times higher than that of dowel type block adopted in the 2nd stage of detailed design. (2) In case that coolant channel outer diameter is 52 mm and hydraulic diameter is 6 mm, the effective coolant flow rates using flange and dowel type fuel blocks are 80 % and 70 % respectively. Because the crossflow loss coefficients of dowel type are lower than that of flange type. (3) The effective coolant flow rate, when crossflow loss coefficients are distributed along with the axial direction, agrees well with that using mean value of crossflow loss coefficient i.e. 5 x 10 11 m -4 . (author)

49 CFR 231.17 - Specifications common to all steam locomotives.

Science.gov (United States)

2010-10-01

... shall be securely fastened with bolts, rivets, or studs. (ii) Locomotives having Wootten type boilers... inches above outside edge of running boards, securely fastened with bolts, rivets, or studs. (c... inches in height, measured from the top of end sill, and securely fastened with bolts or rivets. (f...

Bolt and nut evaluator

Science.gov (United States)

Kerley, James J.; Burkhardt, Raymond; White, Steven

1994-02-01

A device for testing fasteners such as nuts and bolts is described which consists of a fixed base plate having a number of threaded and unthreaded holes of varying size for receiving the fasteners to be tested, a torque marking paper taped on top the fixed base plate for marking torque-angle indicia, a torque wrench for applying torque to the fasteners being tested, and an indicator for showing the torque applied to the fastener. These elements provide a low cost, nondestructive device for verifying the strength of bolts and nuts.

An improved method for calculating force distributions in moment-stiff timber connections

DEFF Research Database (Denmark)

Ormarsson, Sigurdur; Blond, Mette

2012-01-01

An improved method for calculating force distributions in moment-stiff metal dowel-type timber connections is presented, a method based on use of three-dimensional finite element simulations of timber connections subjected to moment action. The study that was carried out aimed at determining how...... the slip modulus varies with the angle between the direction of the dowel forces and the fibres in question, as well as how the orthotropic stiffness behaviour of the wood material affects the direction and the size of the forces. It was assumed that the force distribution generated by the moment action...

Joining technologies for the 1990s: Welding, brazing, soldering, mechanical, explosive, solid-state, adhesive

Science.gov (United States)

Buckley, John D. (Editor); Stein, Bland A. (Editor)

1986-01-01

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Society, and Society of Manufacturing Engineers Conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

Comparing the Methodologies in ASTM G198 Using Combined Hygrothermal-Corrosion Modeling

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

ASTM G198, “Standard test method for determining the relative corrosion performance of driven fasteners in contact with treated wood,” was accepted by consensus and published in 2011. The method has two different exposure conditions for determining fastener corrosion performance in treated wood. The first method places the wood and embedded fasteners in a...

K-Ar dating: incomplete extraction of radiogenic argon from alkali feldspar - a comment

International Nuclear Information System (INIS)

Baksi, A.K.

1984-01-01

In a recent paper, McDowell (1983) discussed the difficulties involved in obtaining accurate K-Ar ages on alkali feldspar samples. These difficulties primarily stem from the fact that the feldspars melt at high temperatures and lack structural volatiles which could flush out all of the 40 Ar* from the viscous melt at temperatures below 1600 0 C. Evidently, if feldspar samples could be satisfactorily melted at lower temperatures by the use of a suitable flux, complete release of 40 Ar* should occur. McDowell (1983) also commented on the lack of a suitable feldspar standard sample for argon dating work. This comment will briefly address these two problems. (Auth.)

Payload Launch Lock Mechanism

Science.gov (United States)

Young, Ken (Inventor); Hindle, Timothy (Inventor)

2014-01-01

A payload launch lock mechanism includes a base, a preload clamp, a fastener, and a shape memory alloy (SMA) actuator. The preload clamp is configured to releasibly restrain a payload. The fastener extends, along an axis, through the preload clamp and into the base, and supplies a force to the preload clamp sufficient to restrain the payload. The SMA actuator is disposed between the base and the clamp. The SMA actuator is adapted to receive electrical current and is configured, upon receipt of the electrical current, to supply a force that causes the fastener to elongate without fracturing. The preload clamp, in response to the fastener elongation, either rotates or pivots to thereby release the payload.

Biobjective Optimization of Vibration Performance of Steel-Spring Floating Slab Tracks by Four-Pole Parameter Method Coupled with Ant Colony Optimization

Directory of Open Access Journals (Sweden)

Hao Jin

2015-01-01

Full Text Available Steel-spring floating slab tracks are one of the most effective methods to reduce vibrations from underground railways, which has drawn more and more attention in scientific communities. In this paper, the steel-spring floating slab track located in Track Vibration Abatement and Control Laboratory was modeled with four-pole parameter method. The influences of the fastener damping ratio, the fastener stiffness, the steel-spring damping ratio, and the steel-spring stiffness were researched for the rail displacement and the foundation acceleration. Results show that the rail displacement and the foundation acceleration will decrease with the increase of the fastener stiffness or the steel-spring damping ratio. However, the rail displacement and the foundation acceleration have the opposite variation tendency for the fastener damping ratio and the steel-spring stiffness. In order to optimize the rail displacement and the foundation acceleration affected by the fastener damping ratio and the steel-spring stiffness at the same time, a multiobjective ant colony optimization (ACO was employed. Eventually, Pareto optimal frontier of the rail displacement and the foundation acceleration was derived. Furthermore, the desirable values of the fastener damping ratio and the steel-spring stiffness can be obtained according to the corresponding Pareto optimal solution set.

SONATINA-1: a computer program for seismic response analysis of column in HTGR core

International Nuclear Information System (INIS)

Ikushima, Takeshi

1980-11-01

An computer program SONATINA-1 for predicting the behavior of a prismatic high-temperature gas-cooled reactor (HTGR) core under seismic excitation has been developed. In this analytical method, blocks are treated as rigid bodies and are constrained by dowel pins which restrict relative horizontal movement but allow vertical and rocking motions. Coulomb friction between blocks and between dowel holes and pins is also considered. A spring dashpot model is used for the collision process between adjacent blocks and between blocks and boundary walls. Analytical results are compared with experimental results and are found to be in good agreement. The computer program can be used to predict the behavior of the HTGR core under seismic excitation. (author)

Investigation of load transfer efficiency in jointed plain concrete pavements (JPCP using FEM

Directory of Open Access Journals (Sweden)

Vahid Sadeghi

2018-05-01

Full Text Available Owing to heavy traffic loads, rigid pavements encounter various types of failures at transverse joints during their lifetime. Three-dimensional finite-element method (3D-FEM was used to assess the structural response of jointed concrete pavement under moving tandem axle loads. In this study, 3D FEM was verified using an existing numerical model and field measurement of the concrete slab traversed by a moving truck. This paper also investigated the effects of multiple parameters: material properties, slab geometry, load magnitude and frictional status of the slab and base layer on load transfer efficiency (LTE of the transverse joints. Further study has been done to investigate the slab performance without the dowel bars which occurs when parts of the pavement needed to be repaired using precast slabs. The aggregate interlock between the new slab and the existing slab is simulated by frictional interface. In 3D FEM model, the load transfer efficiency has been improved by increasing the elasticity modules of the concrete slab and the base layer or increasing the slab thickness. This can decrease the joints' deflections, reduces the damages on pavement joints. Removing dowel bars adversely affected the load transfer. Keywords: Concrete pavement, Load transfer, Finite-element method, Dowel bar, Structural behavior

In vitro fracture resistance of endodontically treated central incisors with varying ferrule heights and configurations.

Science.gov (United States)

Tan, Philip L B; Aquilino, Steven A; Gratton, David G; Stanford, Clark M; Tan, Swee Chian; Johnson, William T; Dawson, Deborah

2005-04-01

The in vitro effectiveness of a uniform circumferential ferrule has been established in the literature; however, the effect of a nonuniform circumferential ferrule height on fracture resistance is unknown. This in vitro study investigated the resistance to static loading of endodontically treated teeth with uniform and nonuniform ferrule configurations. Fifty extracted intact maxillary human central incisors were randomly assigned to 1 of 5 groups: CRN, no root canal treatment (RCT), restored with a crown; RCT/CRN, no dowel/core, restored with a crown; 2 FRL, 2-mm ferrule, cast dowel/core and crown; 0.5/2 FRL, nonuniform ferrule (2 mm buccal and lingual, 0.5 mm proximal), cast dowel/core and crown; and 0 FRL, no ferrule, cast dowel/core and crown. The teeth were prepared to standardized specifications and stored for 72 hours in 100% humidity prior to testing. Testing was conducted with a universal testing machine with the application of a static load, and the load (N) at failure was recorded. Statistical analysis was performed with a 1-way analysis of variance and the Tukey Honestly Significant Difference test (alpha=.05). The mode of fracture was noted by visual inspection for all specimens. There was strong evidence of group differences in mean fracture strength ( P <.0001). Following adjustment for all pairwise group comparisons, it was found that the lack of a ferrule resulted in a significantly lower mean fracture strength (0 FRL: 264.93 +/- 78.33 N) relative to all other groups. The presence of a nonuniform (0.5 to 2-mm vertical height) ferrule (0.5/2 FRL: 426.64 +/- 88.33 N) resulted in a significant decrease ( P =.0001) in mean fracture strength when compared with the uniform 2-mm vertical ferrule (2 FRL: 587.23 +/- 110.25 N), the group without RCT (CRN: 583.67 +/- 86.09 N), and the RCT-treated tooth with a crown alone (CRN/RCT: 571.04 +/- 154.86 N). The predominant mode of failure was an oblique fracture extending from the lingual margin to the facial

Assessment of a Boat Fractured Steering Wheel

Directory of Open Access Journals (Sweden)

Vukelic Goran

2016-09-01

Full Text Available During regular use of the steering wheel mounted on a boat, two cracks emanating from a fastener hole were noticed which, consequently, caused final fracture of the wheel. To determine the behavior of a boat steering wheel with cracks present, assessment of a fractured wheel was performed. Torque moments of the fasteners were measured prior to removing the steering wheel from the boat. Visual and dye penetrant inspection followed along with the material detection. Besides using experimental procedures, assessment of the fractured wheel was performed using finite element analysis, i.e. stress intensity factor values were numerically determined. Variation of stress intensity factor with crack length is presented. Possible causes of crack occurrence are given and they include excessive values of fastener torque moments coupled with fretting between fastener and fastener hole that was poorly machined. Results obtained by this assessment can be taken for predicting fracture behavior of a cracked steering wheel and as a reference in the design, mounting and exploitation process of steering wheels improving that way their safety in transportation environment.

Arvuti poseerib / Steve Farrar

Index Scriptorium Estoniae

Farrar, Steve

1999-01-01

Rootsi disainer Steven Stahlberg on modelliagentuurile "Elite" loonud esimese virtuaalmodelli Webbie Tookay. Virtuaalmodellide tulevikust. Kommenteerivad "Elite Illusion 2K" direktor R. Bellino, briti moefotograaf N. Knight, moeajaloolane C. McDowell.

De dualismos y domesticaciones: Davidson, Mcdowell y Hegel

Directory of Open Access Journals (Sweden)

Luis Guzmán

2016-01-01

Full Text Available El renacimiento del interés por Hegel en el mundo filosófico se apoya en varios puntos: la superación del dualismo entre el esquema conceptual y el contenido (Davidson, McDowell, la disipación del mito de lo dado (Sellars, Quine y el inferencialismo (Brandom. En relación con el primer punto, John McDowell intenta superar aquel dualismo, echando mano de un Hegel cuya retórica requiere de una domesticación. Se intenta iluminar el alcance y algunas limitaciones de esta propuesta, en su intento por desmontar la filosofía del permanente movimiento entre el mito de lo dado o la inmediatez, por un lado, y el coherentismo, por el otro.

The Advanced Thread-Locking Mechanism

Science.gov (United States)

Weiss, Wolfgang

2005-12-01

Locking of threaded members is accomplished by a wide variety of engineering solutions. Generally, in terms of separate locking devices or by built-in locking features such as friction generating means.In regard of space flight vehicles, threaded joints are subject to severe vibration loads during launch, maneuvering, and reentry. This requires fastening systems which are capable to join structural members and attach accessories or equipment in a secure manner. However, manned spacecraft and especially payload components will be subject to installation activity during orbital or interstellar flight maintenance, repair, or mission modification. This, in turn, requires fast separation and engaging of the concerned fasteners, yet providing performance characteristics for high reliable and safe joints.The further described Advanced Thread Locking Mechanism (ATLM) has been developed to combine the merits of both, safe joining technique and a fast installation process. The ATLM uses a freewheel which is securely installed in one part of the threaded member and releasable coupled with the engaged counterpart. While screwing the threaded members together, once coupled, the freewheel will allow free mating of the threaded members including torquing to the desired value. The moment, the pair of threaded fasteners is forced to unscrew (by intended or unintended occurrence of torque in the undoing direction) the freewheel does lock instantly. Disengaging the coupling between the members of the threaded joint takes a separate release action.Owing to the nature of the ATLM, there are a number of design variants ready for implementation.Threaded fasteners in ATLM design are highly recommended for mechanical joints subject to fastening and unfastening during Extra Vehicular Activity (EVA) in course of space flight operations. This is justified through:1. Threaded members mate free running, thus, torque values preset at the wrenching tool are not influenced by varying prevailing

78 FR 20888 - Foreign-Trade Zone (FTZ) 161-Sedgwick County, Kansas; Notification of Proposed Production...

Science.gov (United States)

2013-04-08

...- corrosion coatings; plastic tubes/washers/hoses/seals/sheets/tape/bags/ containers; bushings; funnels...; covers; gaskets; labels; fasteners; bolt extenders; springs; rings; bushings; flanges; hatches; supports...; filters; copper pipes/adapters/fasteners/reducers; aluminum plates/ flanges/covers; locks and locksets...

Remote tool development at the interim examination and maintenance (IEM) cell

International Nuclear Information System (INIS)

Kalk, J.J.

1986-01-01

In the interim examination and maintenance (IEM) cell at the Fast Flux Test Facility, radioactive fuel assemblies from the reactor are disassembled remotely for examination. The cell has an argon atmosphere and all of the equipment in the IEM cell must be either removed or worked on in place remotely for maintenance and repair. Equipment is mounted either on the cell walls or on other equipment with remote fasteners. These fasteners are required to be tightened to torque values ranging from 4 to 102 N m, and will be loosened and torqued several times during the lifetime of the cell. The purpose of this paper is to discuss the development philosophy for tools, specifically those relating to remote fasteners used in IEM cell work. The IEM cell fastener tightening system is now a series of wrenches and attachments instead of the one tool originally proposed. This set of tools allows use of relatively inexpensive commercially available equipment to tighten remote fasteners, while giving the cell operators the flexibility to use the tool they fell is best for the job. If the first choice is not available, use of an optional tool is possible with no loss of torque accuracy

Quick-sealing design for radiological containment

International Nuclear Information System (INIS)

Rampdla, D.S.; Speer, E.

1991-01-01

This patent describes a quick-sealing assembly and method for forming an adhesive seal on opposite sides of a mechanical seal for a flexible containment bag of the type used for working with radioactively contaminated objects. The assembly includes an elongated mechanical fastener having opposing engaging members affixed at a predetermined distance from each of the elongated edges, with an adhesive layer formed between the mechanical fastener and the elongated edge such that upon engagement of the mechanical fastener and adhesive layers to opposing containment fabric, a neat triple hermetic seal is formed

Quick-sealing design for radiological containment

International Nuclear Information System (INIS)

Rampolia, D.S.; Speer, E.

1990-01-01

This patent describes a quick-sealing assembly and method for forming an adhesive seal on opposite sides of a mechanical seal for a flexible containment bag of the type used for working with radioactively contaminated objects. The assembly includes an elongated mechanical fastener having opposing engaging members affixed at a predetermined distance from each of the elongated edges, with an adhesive layer formed between the mechanical fastener and the elongated edge such that upon engagement of the mechanical fastener and adhesive layers to opposing containment fabric, a neat triple hermetic seal is formed

Quick-sealing design for radiological containment

Science.gov (United States)

Rampolia, Donald S.; Speer, Elmer

1990-01-01

A quick-sealing assembly and method for forming an adhesive seal on opposite sides of a mechanical seal for a flexible containment bag of the type used for working with radioactively contaminated objects. The assembly includes an elongated mechanical fastener having opposing engaging members affixed at a predetermined distance from each of the elongated edges, with an adhesive layer formed between the mechanical fastener and the elongated edge such that upon engagement of the mechanical fastener and adhesive layers to opposing containment fabric, a neat triple hermetic seal is formed.

Mechanical behaviour of wood T-joints. Experimental and numerical investigation

Directory of Open Access Journals (Sweden)

C.L. dos Santos

2015-01-01

Full Text Available Results of a double-shear single-dowel wood connection tested under monotonic quasi-static compression loading are presented and discussed in this paper. The wood used in this study was a pine wood, namely the Pinus pinaster species, which is one of the most important Portuguese species. Each connection (specimen consists of three wood members: a centre member, loaded in compression along the parallel-tograin direction and two simply supported side members, loaded along the perpendicular-to-grain direction (Tconnection. The load transfer between wood members was assured by means of a steel dowel, which is representative of the most common joining technique applied for structural details in wooden structures. The complete load-slip behaviour of the joint is obtained until failure. In particular, the values of the stiffness, the ultimate loads and the ductility were evaluated. Additionally, this investigation proposed non-linear 3D finite element models to simulate the T-joint behaviour. The interaction between the dowel and the wood members was simulated using contact finite elements. A plasticity model, based on Hill’s criterion, was used to simulate the joint ductility and cohesive damage modelling was applied to simulate the brittle failure modes (splitting observed in the side members of the joint. The simulation procedure allowed a satisfactory description of the non-linear behaviour of the T-joint including the collapse prediction.

76 FR 28626 - Airworthiness Directives; Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model...

Science.gov (United States)

2011-05-18

... LM Aero believed that there should be a differentiation between the repetitive inspection intervals for Taper-Lok fastened joints (original production configuration) and the inspection intervals for Hi-Tigue fasteners installed in cold-worked holes. LM Aero pointed out that this differentiation is...

77 FR 38547 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-06-28

... (including cracking, misdrilled fastener holes, elongated fastener holes, corrosion, oil-cans, and existing..., corrosion, oil-cans, and existing repairs), or for certain discrepancies, contacting Boeing for repair... Designated Engineering Representative (DER). We have revised the date of the document specified in paragraph...

CONCEPTUAL CONTENT AND UNATTENDED VISUAL FEATURES

Directory of Open Access Journals (Sweden)

Francisco Pereira

2009-01-01

Full Text Available McDowell (1994 propuso una teoría filosófica sobre el contenido perceptual -"conceptualismo"-, que establece que, en todos los casos, el contenido de una experiencial visual necesariamente contiene conceptos que especifican a cabalidad cada uno de los elementos disponibles a nivel consciente y de manera simultánea durante una experiencia. En este artículo cuestionaré la tesis conceptualista, argumentando que algunas experiencias visuales conllevan información acerca de tantos objetos, propiedades y relaciones en un instante, que parece improbable que los sujetos posean e implementen conceptos para cada uno de los elementos representados de forma simultánea por la experiencia en ese momento. Si esto es así, entonces el conceptualismo de McDowell carece de suficiente respaldo.

77 FR 16135 - Airworthiness Directives; Mooney Aviation Company, Inc. (Mooney) Airplanes

Science.gov (United States)

2012-03-20

... assembly for correct positioning and proper attachment and inspecting the Huck Bolt fasteners for proper... Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this... trim assembly for correct positioning and proper attachment and inspecting the Huck Bolt fasteners for...

A robust multi-frequency mixing algorithm for suppression of rivet signal in GMR inspection of riveted structures

Science.gov (United States)

Safdernejad, Morteza S.; Karpenko, Oleksii; Ye, Chaofeng; Udpa, Lalita; Udpa, Satish

2016-02-01

The advent of Giant Magneto-Resistive (GMR) technology permits development of novel highly sensitive array probes for Eddy Current (EC) inspection of multi-layer riveted structures. Multi-frequency GMR measurements with different EC pene-tration depths show promise for detection of bottom layer notches at fastener sites. However, the distortion of the induced magnetic field due to flaws is dominated by the strong fastener signal, which makes defect detection and classification a challenging prob-lem. This issue is more pronounced for ferromagnetic fasteners that concentrate most of the magnetic flux. In the present work, a novel multi-frequency mixing algorithm is proposed to suppress rivet signal response and enhance defect detection capability of the GMR array probe. The algorithm is baseline-free and does not require any assumptions about the sample geometry being inspected. Fastener signal suppression is based upon the random sample consensus (RANSAC) method, which iteratively estimates parameters of a mathematical model from a set of observed data with outliers. Bottom layer defects at fastener site are simulated as EDM notches of different length. Performance of the proposed multi-frequency mixing approach is evaluated on finite element data and experimental GMR measurements obtained with unidirectional planar current excitation. Initial results are promising demonstrating the feasibility of the approach.

76 FR 3561 - Airworthiness Directives; The Boeing Company Model 777-200 and -300 Series Airplanes Equipped...

Science.gov (United States)

2011-01-20

... studs, blanket studs, and temporary fasteners; replacement of sealant if necessary; and related... installed Doing a detailed inspection of the T/R panel wall inner bolt holes for elongation Doing a general... click bond stud, blanket stud, and temporary fastener is loose, damaged, or missing Doing an NDT (eddy...

A comparative evaluation of linear dimensional accuracy of the dies obtained using three conceptually different die systems in the fabrication of implant prosthesis: An in vitro study

Directory of Open Access Journals (Sweden)

Manawar Ahmad

2014-01-01

Purpose: The purpose of the study was to evaluate the linear dimensional accuracy between the implant master die and three conceptually different die systems such as Pindex system, Accu-trac precision die system, and Conventional brass dowel pin system. Materials and Methods: Thirty impressions of implant master die were made with polyether impression material. Ten experimental implant casts were fabricated for each of the three different die systems tested: Accu-trac precision die tray system, Pindex system, and conventional brass dowel pin system. The solid experimental casts were sectioned and then removed from the die system 30 times. Linear distances between all six possible distances were measured from one centre of the transfer coping to the other, using a co-ordinate measuring machine in millimeters up to accuracy of 0.5 microns. Data were tabulated and statistically analyzed by Binomial non parametric test using SPSS version 15. Results: Significant differences were found for distance A-B (P = 0.002, A-C ( P = 0.002, A-D (P value = 0.002, and B-D ( P = 0.021 in Conventional Dowel pin system however for Accu-trac precision die tray system, it was significant only for distance A-D (P = 0.002 but for Pindex system it was non-significant for all the distances measured. Conclusion: Within the limitations of this study, use of Pindex system is recommended when sectioned dies are needed for a multi implant retained prosthesis.

Reactor fuel assembly fastening

International Nuclear Information System (INIS)

Formanek, F.J.; Schukei, G.E.

1980-01-01

A nuclear fuel assembly is described, adapted to be locked into first mating surfaces on a core support stand, comprising a lower end fitting having posts for resting on the stand; elongated hook members pivotally connected at one end to the lower end fitting and having a second mating surface at the other end to engage the first mating surfaces; actuating means located between the posts on the lower end fitting and being vertically movable relative to the end fitting; and rigid links pivotally attached at one end to the hook members intermediate the connection of the hook members to the end fitting and the second mating surface and pivotally attached at the other end to the actuating means, the link having a length between the pivoted connections such that the second mating surface on the hook members locks into engagement with the first mating surfaces on the stand as the links approach the horizontal. (author)

77 FR 64545 - Drawn Stainless Steel Sinks From China

Science.gov (United States)

2012-10-22

... clips, fasteners, seals, and sound-deadening pads are also covered by the scope of these investigations..., fasteners, seals, and sound-deadening pads are not covered by the scope of these investigations if they are... 61937 (Oct. 6, 2011) and the newly revised Commission's Handbook on E-Filing, available on the...

29 CFR 1926.307 - Mechanical power-transmission apparatus.

Science.gov (United States)

2010-07-01

... fastened with metal in any case, nor with any other fastening which by construction or wear will constitute..., DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Tools-Hand and Power § 1926... belt and pulley guard. (3) For the Textile Industry, because of the presence of excessive deposits of...

Are You Thinking about Suicide? How to Stay Safe and Find Treatment

Science.gov (United States)

... number — in the United States, call the National Suicide Prevention Lifeline at 800-273-TALK (800-273-8255) ... www.dbsalliance.org/site/PageServer?pagename=education_brochures_suicide_prevention. Accessed April 30, 2015. McDowell AK, et al. ...

Nodding Syndrome

Centers for Disease Control (CDC) Podcasts

2013-12-19

Dr. Scott Dowell, a CDC director, discusses the rare illness, nodding syndrome, in children in Africa.  Created: 12/19/2013 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 1/27/2014.

Effect of chloride-based deicers on reinforced concrete structures.

Science.gov (United States)

2012-07-01

We conducted an extensive literature review and performed laboratory tests to assess the effect of chloride-based deicers on the rebars and dowel bars in concrete and to determine whether or not deicer corrosion inhibitors help preserve the transport...

Internally Mounting Strain Gages

Science.gov (United States)

Jett, J. R., Jr.

1984-01-01

Technique for mounting strain gages inside bolt or cylinder simultaneously inserts gage, attached dowel segment, and length of expandable tubing. Expandable tubing holds gage in place while adhesive cures, assuring even distribution of pressure on gage and area gaged.

Heavy vehicle simulator (HVS) evaluation of load transfer efficiency and continuously reinforced concrete inlays on the N3 near Pietermartizburg

CSIR Research Space (South Africa)

Du Plessis, L

2006-07-01

Full Text Available The paper addresses two different heavy Vehicle Simulator (HVS) studies conducted on concrete: Load transfer through aggregate interlock and the use of dowels and the evaluation of the performance of an in-service continuously reinforced concrete...

Comparing the Methodologies in ASTM G198: Is There an Easy Way Out?

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

ASTM(1) G198, Standard test method for determining the relative corrosion performance of driven fasteners in contact with treated wood, was accepted by consensus and published in 2011. The method has two different exposure conditions for determining fastener corrosion performance in treated wood. The first method places the wood and embedded...

Thick Concepts, Non-Cognitivism, and Wittgenstein's Rule ...

African Journals Online (AJOL)

following considerations to show that such a non-cognitivist view is untenable. In this paper I do several things. I describe the non-cognitivist position in its various forms and explain its driving motivations. I then explain McDowell's argument ...

Accelerated testing for studying pavement design and performance (FY 2000) : effectiveness of fiber reinforced and plain, ultra-thin concrete overlays on Portland Cement Concrete Pavement (PCCP).

Science.gov (United States)

2003-11-01

The objective of the research was to compare the performance of fiber reinforced and plain PCC concrete overlay when used as a thin non-dowelled overlay on top of a rubblized, distressed concrete pavement. The experiment was conducted at the Accelera...

Making It Totally Explicit | Dowell | Philosophical Papers

African Journals Online (AJOL)

This paper begins by isolating the reductive component of Brandom's inferentialism. In order to assess to what extent the reductive component is supported by the considerations Brandom marshals in its defense, I assess the comparative degree of support these considerations provide for a non-reductive counterpart of ...

Dowel Bar Retrofit Mix Design and Specification

Science.gov (United States)

2012-02-01

The focus of this project was on identifying critical properties that control longterm performance of repair concrete, especially rapidsetting : materials extended using pea gravel (maximum size aggregate 9.5 mm). : In the first phase of this proj...

Urine cup for collection of urine from cows.

Science.gov (United States)

Fellner, V; Weiss, M F; Belo, A T; Belyea, R L; Martz, F A; Orma, A H

1988-08-01

A urine cup for continuous and complete collection of urine from cows was constructed from Plastisol, cotton webb strapping, Velcro Brand touch fasteners [corrected], snap-fasteners, denim patches, weather stripping, and vacuum hose. The urine cup was made from Plastisol using a heated lead mold. It was large enough to enclose a 9 cm x 6 cm area around the vulva of a cow and was attached by strapping and Velcro Brand touch fasteners [corrected] to patches glued to the rump. Urine cups were used repeatedly and provided for long-term collection of urine from cows, eliminating the need for indwelling catheters. Applications include long-term nutrient balance, radioisotope, and metabolism studies.

76 FR 25763 - Qualification of Drivers; Exemption Applications; Vision

Science.gov (United States)

2011-05-05

... with the vision deficiency: Christopher Kahl, Althea Renita Dowell, Steven DuBois, Steve Campbell... Pulido, Oliver Murphy, Jerome Smalls, Alan Jenkins, Ryan Forsythe, Terry L. Randoll, Edward Joseph... for an exemption. Thomas L. Newingham, Joseph Barlow. The following 2 applicants do not have...

デカルト的な心の概念をめぐるマクダウェルとメルロ＝ポンティ

DEFF Research Database (Denmark)

Jensen, Rasmus Thybo

2012-01-01

to draw attention to what I consider an additional potentially fruitful meeting point between the philosophies of Merleau-Ponty and McDowell, namely their critique of a certain Cartesian picture of the mind. My aim is to demonstrate how both authors regard a certain conception of nature rather than some......Recently a number of authors have appealed to the early works of Merleau-Ponty in a critique of the picture of perception presented by McDowell. This debate has been focused on McDowell’s claim that conceptual capacities are essentially involved in our perceptual experiences. In this paper I wish...... independent epistemological project as the background assumption which gives the Cartesian picture its attraction. Furthermore I want to bring out how they share a general conception of the nature of the problem generated by this background assumption. They both regard the problem as a transcendental problem...

Examination of pulsed eddy current for inspection of second layer aircraft wing lap-joint structures using outlier detection methods

Energy Technology Data Exchange (ETDEWEB)

Butt, D.M., E-mail: Dennis.Butt@forces.gc.ca [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada); Underhill, P.R.; Krause, T.W., E-mail: Thomas.Krause@rmc.ca [Royal Military College of Canada, Dept. of Physics, Kingston, Ontario (Canada)

2016-09-15

Ageing aircraft are susceptible to fatigue cracks at bolt hole locations in multi-layer aluminum wing lap-joints due to cyclic loading conditions experienced during typical aircraft operation, Current inspection techniques require removal of fasteners to permit inspection of the second layer from within the bolt hole. Inspection from the top layer without fastener removal is desirable in order to minimize aircraft downtime while reducing the risk of collateral damage. The ability to detect second layer cracks without fastener removal has been demonstrated using a pulsed eddy current (PEC) technique. The technique utilizes a breakdown of the measured signal response into its principal components, each of which is multiplied by a representative factor known as a score. The reduced data set of scores, which represent the measured signal, are examined for outliers using cluster analysis methods in order to detect the presence of defects. However, the cluster analysis methodology is limited by the fact that a number of representative signals, obtained from fasteners where defects are not present, are required in order to perform classification of the data. Alternatively, blind outlier detection can be achieved without having to obtain representative defect-free signals, by using a modified smallest half-volume (MSHV) approach. Results obtained using this approach suggest that self-calibrating blind detection of cyclic fatigue cracks in second layer wing structures in the presence of ferrous fasteners is possible without prior knowledge of the sample under test and without the use of costly calibration standards. (author)

Examination of pulsed eddy current for inspection of second layer aircraft wing lap-joint structures using outlier detection methods

International Nuclear Information System (INIS)

Butt, D.M.; Underhill, P.R.; Krause, T.W.

2016-01-01

Ageing aircraft are susceptible to fatigue cracks at bolt hole locations in multi-layer aluminum wing lap-joints due to cyclic loading conditions experienced during typical aircraft operation, Current inspection techniques require removal of fasteners to permit inspection of the second layer from within the bolt hole. Inspection from the top layer without fastener removal is desirable in order to minimize aircraft downtime while reducing the risk of collateral damage. The ability to detect second layer cracks without fastener removal has been demonstrated using a pulsed eddy current (PEC) technique. The technique utilizes a breakdown of the measured signal response into its principal components, each of which is multiplied by a representative factor known as a score. The reduced data set of scores, which represent the measured signal, are examined for outliers using cluster analysis methods in order to detect the presence of defects. However, the cluster analysis methodology is limited by the fact that a number of representative signals, obtained from fasteners where defects are not present, are required in order to perform classification of the data. Alternatively, blind outlier detection can be achieved without having to obtain representative defect-free signals, by using a modified smallest half-volume (MSHV) approach. Results obtained using this approach suggest that self-calibrating blind detection of cyclic fatigue cracks in second layer wing structures in the presence of ferrous fasteners is possible without prior knowledge of the sample under test and without the use of costly calibration standards. (author)

Flow Control of Flexible Structures

Science.gov (United States)

2017-09-06

levels of modeling [Dowell and Hall, 2001]. Fur- thermore, even for the most complex models, the main research goal has been a mathe - matical description...possibility for localized, discrete actuation to coun- teract detrimental flow developments before they result in significant structural loads and

Embedded adhesive connection for laminated glass plates

DEFF Research Database (Denmark)

Hansen, Jens Zangenberg; Poulsen, S.H.; Bagger, A.

2012-01-01

The structural behavior of a new connection design, the embedded adhesive connection, used for laminated glass plates is investigated. The connection consists of an aluminum plate encapsulated in-between two adjacent triple layered laminated glass plates. Fastening between glass and aluminum...... usage in a design situation. The embedded connection shows promising potential as a future fastening system for load-carrying laminated glass plates....

McDowell’s New Conceptualism and the Difference between Chickens, Colours and Cardinals

DEFF Research Database (Denmark)

Gersel, Johan Peter; Thybo Jensen, Rasmus; Thaning, Morten Sørensen

2017-01-01

McDowell recently renounced the assumption that the content of any knowledgeable, perceptual judgement must be included in the content of the knowledge grounding experience. We argue that McDowell’s introduction of a new category of non-inferential, perceptual knowledge is incompatible with the m...

Noor mässaja / Kalmer Saar

Index Scriptorium Estoniae

Saar, Kalmer

2004-01-01

Briti Nõukogu toetusel Pärnus, Tartus ja Tallinnas toimuvatel inglise filmide päevadel "Geeniuste mäss" näidatakse ka 3 Lindsay Andersoni nn. Travise triloogia filmi "Kui..." (1968), "Oo, õnneseen!" (1973) ja "Ravila Britannia" (1982), kus Mick Travise rollis on Malcolm McDowell (1943)

Effect of biomimetic non-smooth unit morphology on thermal fatigue behavior of H13 hot-work tool steel

Science.gov (United States)

Meng, Chao; Zhou, Hong; Cong, Dalong; Wang, Chuanwei; Zhang, Peng; Zhang, Zhihui; Ren, Luquan

2012-06-01

The thermal fatigue behavior of hot-work tool steel processed by a biomimetic coupled laser remelting process gets a remarkable improvement compared to untreated sample. The 'dowel pin effect', the 'dam effect' and the 'fence effect' of non-smooth units are the main reason of the conspicuous improvement of the thermal fatigue behavior. In order to get a further enhancement of the 'dowel pin effect', the 'dam effect' and the 'fence effect', this study investigated the effect of different unit morphologies (including 'prolate', 'U' and 'V' morphology) and the same unit morphology in different sizes on the thermal fatigue behavior of H13 hot-work tool steel. The results showed that the 'U' morphology unit had the optimum thermal fatigue behavior, then the 'V' morphology which was better than the 'prolate' morphology unit; when the unit morphology was identical, the thermal fatigue behavior of the sample with large unit sizes was better than that of the small sizes.

Elasto-Plastic 3D Finite Element Contact Analysis of a Hole Containing a Circular Insert in a Fatigue Test Coupon

Science.gov (United States)

2015-08-01

Australian Air Force (RAAF) airframes. An aluminium - alloy fatigue test coupon (see Figure 1) has been designed and applied in support of the validation of...manufactured from aerospace aluminium alloy material (see Section 4 for further details). Unloaded close-fit fasteners of small diametric clearance were...Abaqus elasto–plastic input data requirements The aluminium and titanium alloys used in the coupon and fastener material display linear- elastic

Evaluation of PEGIT duct connection system

Energy Technology Data Exchange (ETDEWEB)

Walker, Iain S.; Brenner, Douglas E.; Sherman, Max H.; Dickerhoff, Darryl J.

2003-08-01

Most air duct system components are assembled in the field and are mechanically fastened by sheet metal screws (for sheet metal-to-sheet metal) or by drawbands (for flex duct-to-sheet metal). Air sealing is separate from this mechanical fastening and is usually achieved using tape or mastic products after mechanical fastening. Field observations have shown that mechanical fastening rarely meets code or manufacturers requirements and that sealing procedures are similarly inconsistent. To address these problems, Proctor Engineering Group (PEG) is developing a system of joining ducts (called PEGIT) that combines the mechanical fastening and sealing into a single self-contained procedure. The PEGIT system uses a shaped flexible seal between specially designed sheet metal duct fittings to both seal and fasten duct sections together. Figure 1 shows the inner duct fitting complete with rubber seal. This seal provides the air seal for the completed fitting and is shaped to allow the inner and outer fittings to slide together, and then to lock the fittings in place. The illustration in Figure 2 shows the approximate cross section of the rubber seal that shows how the seal has a lip that is angled backwards. This angled lip allows the joint to be pushed together by folding flat but then its long axis makes it stiff in the pulling apart direction. This study was undertaken to assist PEG in some of the design aspects of this system and to test the performance of the PEGIT system. This study was carried out in three phases. The initial phase evaluated the performance of a preliminary seal design for the PEGIT system. After the first phase, the seal was redesigned and this new seal was evaluated in the second phase of testing. The third phase performed more detailed testing of the second seal design to optimize the production tolerances of the sheet metal fittings. This report summarizes our findings from the first two phases and provides details about the third phase of testing.

76 FR 54408 - Regulatory Review Schedule

Science.gov (United States)

2011-09-01

... 16, 2011 National Tribal Gaming Chukchansi Gold Resort & 1, 2, 4, 5 Commissioner/Regulator Casino... Clearwater Casino Resort 1, 2, 4, 5 Suquamish, WA. December 13, 2011 NIGC Consultation DOI South Auditorium 1... NIGC Consultation Fort McDowell Casino 5 Scottsdale, AZ. November 30-December 1, 2011 NIGC Consultation...

Katariina kirikus algab Geeniuste mäss / Kai Ilustrumm

Index Scriptorium Estoniae

Ilustrumm, Kai

2004-01-01

Briti Nõukogu toetusel Pärnus, Tartus ja Tallinnas toimuvatel inglise filmide päevadel "Geeniuste mäss" näidatakse ka 3 Lindsay Andersoni nn. Travise triloogia filmi "Kui..." (1968), "Oo, õnneseen!" (1973) ja "Ravila Britannia" (1982), kus Mick Travise rollis on Malcolm McDowell (1943). Lisatud kava

Three Sorts of Naturalism

DEFF Research Database (Denmark)

Fink, Hans

2006-01-01

In "Two sorts of Naturalism" John McDowell is sketching his own sort of naturalism in ethics as an alternative to "bald naturalism". In this paper I distinguish materialist, idealist and absolute conceptions of nature and of naturalism in order to provide a framework for a clearer understanding...

As good as the real thing? Performance differences for live versus recorded stimuli in an everyday listening task

DEFF Research Database (Denmark)

Kirkwood, Brent Christopher

2005-01-01

an acoustic head and torso simulator, and 3) diotic presentation of monaurally recorded stimuli. Live presentation of stimuli has already been used by C. Carello, et al. [Psychological Science 9, 211-214 (1998)] to demonstrate that humans can hear reasonably well the length of wooden dowels dropped onto hard...

Pull Out All the Stops, and Give Staff Development the Go.

Science.gov (United States)

Sams, Peggy

1987-01-01

To benefit fully from the consultants and guest lecturers hired to conduct inservice training for teachers, the McDowell County schools (North Carolina) cultivate a "red carpet" treatment policy for such visitors. Success depends on good two-way communication, efficient hospitality arrangements, administrative presence at workshops, and an…

Behavioral Indicators of Legal and Illegal Gun Carrying

Science.gov (United States)

2015-05-01

foundation to develop training for law enforcement and security personnel to utilize behavioral indicators in a safe, legal, and effective manner...hope to develop more efficient and effective means of assisting the police to identify and safely interdict persons carrying illegal firearms. This...by Velcro hook and loop fastener tape. Attached to the elastic wrap is a pocket with a security strap that holds the gun in place. When fastened to

Galvanic corrosion study of aluminium alloy plates mounted to stainless and mild steel bolts by accelerated exposure test

OpenAIRE

MREMA, Emmanuel; ITOH, Yoshito; KANEKO, Akira; HIROHATA, Mikihito

2016-01-01

Despite the fact that aluminium alloy members have a proven durability over stainless steel members, their joint fasteners like bolts, nuts and washers are drawn from steel material due to aluminium alloy inferior mechanical properties. Bare contact between aluminium alloy members and stainless steel fasteners results to galvanic corrosion of aluminium alloy members. A corrosion behaviour study was carried out on different aluminium alloy types with different surface treatments mounted to sta...

Mechanical performance and contact zone of timber joint with oblique faces

Czech Academy of Sciences Publication Activity Database

Kunecký, Jiří; Sebera, V.; Tippner, J.; Hasníková, Hana; Kloiber, Michal; Arciszewska-Kędzior, Anna; Milch, J.

2015-01-01

Roč. 63, č. 4 (2015), s. 1153-1159 ISSN 1211-8516 R&D Projects: GA MK(CZ) DF12P01OVV004 Keywords : bending * contact zone * digital image correlation * dowel * non-destructive test ing * timber joint Subject RIV: AL - Art, Architecture, Cultural Heritage http://dx.doi.org/10.11118/actaun201563041153

Background paper on Young Migrants in Urban Ghana, focusing particularly on young female head porters (kayayei)

NARCIS (Netherlands)

R.B.C. Huijsmans (Roy)

2012-01-01

textabstractIn much of the developing world, migration is part and parcel of people’s lives (see for example: McDowell /De Haan 1997: 3). This is also the case in Ghana where people move for numerous reasons. Yet, work is probably the main reason why people migrate. As the case elsewhere in the

When Police Intervene: Race, Gender, and Discipline of Black Male Students at an Urban High School

Science.gov (United States)

Hines-Datiri, Dorothy

2015-01-01

Courtney and Dennis, two African American male students at McDowell High, were arrested at school for throwing water balloons during senior prank week. The principal assigned two police officers to the magnet school to oversee the implementation of a new discipline protocol. However, several members of the school staff were ill-informed about the…

The end-state comfort effect in bimanual grip selection.

Science.gov (United States)

Fischman, Mark G; Stodden, David F; Lehman, Davana M

2003-03-01

During a unimanual grip selection task in which people pick up a lightweight dowel and place one end against targets at variable heights, the choice of hand grip (overhand vs. underhand) typically depends on the perception of how comfortable the arm will be at the end of the movement: an end-state comfort effect. The two experiments reported here extend this work to bimanual tasks. In each experiment, 26 right-handed participants used their left and right hands to simultaneously pick up two wooden dowels and place either the right or left end against a series of 14 targets ranging from 14 to 210 cm above the floor. These tasks were performed in systematic ascending and descending orders in Experiment 1 and in random order in Expiment 2. Results were generally consistent with predictions of end-state comfort in that, for the extreme highest and lowest targets, participants tended to select opposite grips with each hand. Taken together, our findings are consistent with the concept of constraint hierarchies within a posture-based motion-planning model.

Foundation Design for a High Bay Warehouse with a Steel Fibre Reinforced Concrete Slab

DEFF Research Database (Denmark)

Kasper, T.; Sørensen, Carsten Steen; Nielsen, J. B.

2008-01-01

. The SFRC slab is cast in 6 panels divided by free-movement joints with shear dowels. It has to be designed for closely spaced 250 kN characteristic long-term loads for complete filling of the racks. The design has been based on a German SFRC design guideline and makes use of 3D finite element soil...

Experimental assessment of a full-scale lap scarf timber joint accompanied by a finite element analysis and digital image correlation

Czech Academy of Sciences Publication Activity Database

Kunecký, Jiří; Sebera, V.; Hasníková, Hana; Arciszewska-Kędzior, Anna; Tippner, J.; Kloiber, Michal

2015-01-01

Roč. 76, February (2015), s. 24-33 ISSN 0950-0618 R&D Projects: GA MK(CZ) DF12P01OVV004 Keywords : historicist joint * full-scale testing * finite element analysis * dowel * digital image correlation Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 2.421, year: 2015 http://www.sciencedirect.com/science/article/pii/S095006181401246X

ФОРМИРОВАНИЕ ПРОСТРАНСТВЕННОЙ ЖЕСТКОСТИ РЕЛЬСОВЫХ ОПОР ПРИ ШПАЛАХ СБ-3-0 И СКРЕПЛЕНИЯХ КПП-5

OpenAIRE

Darenskiy, Olexander; Potapov, Dmytro; Kulik, Stanislav

2017-01-01

Аt action on the rail of forces vertical and lateral there is its bend in a plane vertical andhorizontal and its twisting. The reactions of the rail fastening and reactive croutni vertical andhorizontal are the constituents of reactions of rail supports moments. Therefore in the given work isexamined vertical and horizontal transversal inflexibilities of fastening to the type CPP-5-5 atbends and his inflexibility at twisting of rail.Rozrahovouyochi action of these forces, it is needed to take...

Torque application technique and apparatus

Science.gov (United States)

Pineault, Raymond P.

1993-11-01

A tool which produces a measured torque is coupled to a bolt head or nut, located in a relatively inaccessible area, by apparatus which includes a wrench member affixed to an adaptor. The wrench member is sized and shaped to engage the fastener to be operated upon and the adaptor has a tubular construction with a tool engaging socket at one end. The adaptor is provided with an elongated slot which accommodates any wires which may pass through the fastener.

Installation Torque Tables for Noncritical Applications

Science.gov (United States)

Rivera-Rosario, Hazel T.; Powell, Joseph S.

2017-01-01

The objective of this project is to define torque values for bolts and screws when loading is not a concern. Fasteners require a certain torque to fulfill its function and prevent failure. NASA Glenn Research Center did not have a set of fastener torque tables for non-critical applications without loads, usually referring to hand-tight or wrench-tight torqueing. The project is based on two formulas, torque and pullout load. Torque values are calculated giving way to preliminary data tables. Testing is done to various bolts and metal plates, torqueing them until the point of failure. Around 640 torque tables were developed for UNC, UNF, and M fasteners. Different lengths of thread engagement were analyzed for the 5 most common materials used at GRC. The tables were put together in an Excel spreadsheet and then formatted into a Word document. The plan is to later convert this to an official technical publication or memorandum.

A system for rotatably mounting a vessel to a loading buoy. System for dreibar tilkopling av et flytende farty til en lastebye

Energy Technology Data Exchange (ETDEWEB)

Breivik, K.; Smedal, A.; Syvertsen, K.

1994-07-04

The invention relates to a system for rotatable mounting of a floating vessel to a submerged loading/unloading buoy which is anchored to the sea bed. The buoy is adapted to be introduced into and fastened in a releasable manner in a submerged downwardly open receiving space in the vessel, and is during operation connected to at least one transfer line and forming a transfer connection between this line and a tube system on the vessel. The buoy comprises an outer member which is arranged to be rigidly fastened in the receiving space, and a central inner member which is rotatably mounted in the outer member, so that the vessel is able to turn about the central member when the buoy is fastened in the receiving space. Further, the upper end of the central member is connected to the tube system of the vessel through a swivel means and through at least one flexible joint means respectively. 3 figs.

Automation of the Design of the Anchorage System Taking into Account the Geomechanical State of the Massif and Mining Development Schemes

Directory of Open Access Journals (Sweden)

Demin Vladimir

2018-01-01

Full Text Available The article presents the system for the automation of the design of the anchorage, which regulates the calculation of the required parameters of the fasteners for the fastening of the fastening system. The main factors affecting the operation of the anchor support are grouped in the following way: mining and geological conditions, technical characteristics of the anchor support, geomechanical conditions for conducting and operating the mine workings. Mining and geological conditions for carrying out excavations include: physical and mechanical properties of rocks, the category of roof stability, fracturing, etc. Technical characteristics of the anchor support: material of the rod, filler, filling completeness, etc. Conditions (geomechanical of carrying out and exploitation of the mine workings: the depth of the conduct, the location relative to the zone of influence of the cleaning works, the location relative to the waste zone, etc. As a result of calculations the program gives out the basic parameters of the anchor support, which coincide with the parameters adopted by the passport.

Wall insulation system

Energy Technology Data Exchange (ETDEWEB)

Kostek, P.T.

1987-08-11

In a channel specially designed to fasten semi-rigid mineral fibre insulation to masonry walls, it is known to be constructed from 20 gauge galvanized steel or other suitable material. The channel is designed to have pre-punched holes along its length for fastening of the channel to the drywall screw. The unique feature of the channel is the teeth running along its length which are pressed into the surface of the butted together sections of the insulation providing a strong grip between the two adjacent pieces of insulation. Of prime importance to the success of this system is the recent technological advancements of the mineral fibre itself which allow the teeth of the channel to engage the insulation fully and hold without mechanical support, rather than be repelled or pushed back by the inherent nature of the insulation material. After the insulation is secured to the masonry wall by concrete nail fastening systems, the drywall is screwed to the channel.

2010 CERT Research Report

Science.gov (United States)

2011-09-01

extensive and expensive rework before implementation. Analysis of catastrophe helps us to see how complex, multi-system, multi-organizational...Cyber Security Science of Cyber Security, published by JASON , an independent scientific advisory group that provides consulting services to the U.S...Ed Desautels Lisa Gardner Alexa Huth Mindi McDowell Amanda Parente Pennie Walters Contributing Team Members Michelle Fried Lisa Marino Design David

Influenza Pandemic Infrastructure Response in Thailand

Centers for Disease Control (CDC) Podcasts

Influenza viruses change antigenic properties, or drift, every year and they create seasonal outbreaks. Occasionally, influenza viruses change in a major way, called a “shift." If an influenza virus shifts, the entire human population is susceptible to the new influenza virus, creating the potential for a pandemic. On this podcast, CDC's Dr. Scott Dowell discusses responding to an influenza pandemic.

Photovoltaic array mounting apparatus, systems, and methods

Science.gov (United States)

West, Jack Raymond; Atchley, Brian; Hudson, Tyrus Hawkes; Johansen, Emil

2016-01-05

A photovoltaic array, including: (a) supports laid out on a surface in rows and columns; (b) photovoltaic modules positioned on top of the supports; and (c) fasteners connecting the photovoltaic modules to the supports, wherein the supports have an upper pedestal surface and a lower pedestal surface such that the photovoltaic modules are positioned at a non-horizontal angle when edges of the photovoltaic modules are positioned on top of the upper and lower pedestal surfaces, and wherein a portion of the fasteners rotate to lock the photovoltaic modules onto the supports.

Fuel assembly

International Nuclear Information System (INIS)

Fujibayashi, Toru.

1970-01-01

Herein disclosed is a fuel assembly in which a fuel rod bundle is easily detachable by rotating a fuel rod fastener rotatably mounted to the upper surface of an upper tie-plate supporting a fuel bundle therebelow. A locking portion at the leading end of each fuel rod protrudes through the upper tie-plate and is engaged with or separated from the tie-plate by the rotation of the fastener. The removal of a desired fuel rod can therefore be remotely accomplished without the necessity of handling pawls, locking washers and nuts. (Owens, K.J.)

Camshaft bearing arrangement for overhead cam engine

Energy Technology Data Exchange (ETDEWEB)

Yoshikawa, M.

1985-01-01

In an assembly for an internal combustion engine comprising a cylinder block, a cylinder head detachably affixed to the cylinder block by a plurality of threaded fastening means, a plurality of poppet valves supported for reciprocation in the cylinder head and a camshaft for operating the poppet valves, the improvement is described comprising a cam carrier detachably affixed to the cylinder head and overlying the threaded fastening means, and a bearing cap affixed to the cam carrier. The cam carrier and the bearing cap have bearing surfaces for journaling the camshaft.

Comparison of Different Assembling Techniques Regarding Cost, Durability, and Ecology - A Survey of Multi-layer Wooden Panel Assembly Load-Bearing Construction Elements

Directory of Open Access Journals (Sweden)

Dietrich Buck

2015-10-01

Full Text Available Wood is a pure, sustainable, renewable material. The increasing use of wood for construction can improve its sustainability. There are various techniques to assemble multi-layer wooden panels into prefabricated, load-bearing construction elements. However, comparative market and economy studies are still scarce. In this study, the following assembling techniques were compared: laminating, nailing, stapling, screwing, stress laminating, doweling, dovetailing, and wood welding. The production costs, durability, and ecological considerations were presented. This study was based on reviews of published works and information gathered from 27 leading wood product manufacturing companies in six European countries. The study shows that the various techniques of assembling multi-layer wooden construction panel elements are very different. Cross laminated timber (CLT exhibited the best results in terms of cost and durability. With regard to ecological concerns, dovetailing is the best. Taking into account both durability and ecological considerations, wooden screw-doweling is the best. These alternatives give manufacturers some freedom of choice regarding the visibility of surfaces and the efficient use of lower-quality timber. CLT is the most cost-effective, is not patented, and is a well-established option on the market today.

Clinical Outcomes of Zirconium-Oxide Posts: Up-to-Date Systematic Review.

Science.gov (United States)

Al-Thobity, Ahmad M

2016-06-01

The aim of this systematic review was to investigate the clinical outcomes of the use of zirconium-oxide posts in the past 20 years. The addressed question was: Do zirconium-oxide posts maintain the long-term survival rate of endodontically treated teeth? A database search was made of articles from January 1995 to December 2014; it included combinations of the following keywords: "zirconia," "zirconium oxide," "dowel/dowels," "post/posts," and "post and core." Exclusion criteria included review articles, experimental studies, case reports, commentaries, and articles published in a language other than English. Articles were reviewed by the titles, followed by the abstracts, and, finally, the full text of the selected studies. Four studies were included after filtering the selected studies according to the inclusion and exclusion criteria. In one study, the prefabricated zirconia posts with indirect glass-ceramic cores had significantly higher failure rates than other posts with direct composite cores. In two studies, no failure of the cemented posts was observed throughout the follow-up period. Due to the limited number of clinical studies, it can be concluded that the long-term success rate of prefabricated zirconium-oxide posts is unclear.

Bending stress modeling of dismountable furniture joints applied with a use of finite element method

Directory of Open Access Journals (Sweden)

Milan Šimek

2009-01-01

Full Text Available Presented work focuses on bending moment stress modeling of dismountable furniture joints with a use of Finite Element Method. The joints are created from Minifix and Rondorfix cams combined with non-glued wooden dowels. Laminated particleboard 18 mm of thickness is used as a connected material. The connectors were chosen such as the most applied kind in furniture industry for the case furniture. All gained results were reciprocally compared to each other and also in comparison to experimental testing by the mean of stiffness. The non-linear numerical model of chosen joints was successfully created using the software Ansys Workbench. The detailed analysis of stress distribution in the joint was achieved with non-linear numerical simulation. A relationship between numerical si­mu­la­tion and experimental testing was showed by comparison stiffness tangents. A numerical simulation of RTA joint loads also demonstrated the important role of non-glued dowels in the tested joints. The low strength of particleboard in the tension parallel to surface (internal bond is the most likely the cause of the joint failure. Results are applicable for strength designing of furniture with the aid of Computer Aided Engineering.

Effect of CFRP and TRM Strengthening of RC Slabs on Punching Shear Strength

Directory of Open Access Journals (Sweden)

Husain Abbas

Full Text Available Abstract The paper presents experiments involving punching of RC slabs strengthened using externally bonded carbon fiber reinforced polymer (CFRP sheet and textile reinforced mortar (TRM. Twelve RC slab specimens of two concrete grades (39.9 and 63.2 MPa and employing two strengthening schemes (CFRP and TRM were tested. Specimens were supported on two opposite edges. Experimental load-displacement variations show two peak loads in strengthened slabs and one peak followed by a plateau in control. Second peak or the plateau corresponds to the combined action of aggregate interlock and the dowel action of back face rebars and strengthening layers. The dowel action of back face rebars and strengthening layers had no role in ultimate punching load (i.e. first peak. Strengthened slabs showed 9-18% increase in ultimate punching load (i.e. first peak whereas there was significant increase in the second peak load (190-276% for CFRP; 55-136% for TRM and energy absorption (~66% for CFRP and 22-56% for TRM. An analytical model was also developed for predicting the punching shear strength (first and second peaks of strengthened slabs showing good comparison with experiments.

Retaining Ring Fastener for Solar Panels

Science.gov (United States)

Wilson, A. H.

1983-01-01

Simple articulating linkage secures solar panels into supporting framework. Five element linkage collapses into W-shape for easy placement into framework, then expands to form rectangle of same dimensions as those of panel.

Quality audit in the fastener industry

Science.gov (United States)

Reagan, John R.

1995-09-01

Both the financial and quality communities rely on audits to verify customers records. The financial community is highly structured around three categories of risk, INHERENT RISK, CONTROL RISK, and DETECTION RISK. Combined, the product of these three categories constitute the AUDIT RISK. The financial community establishes CONTROL RISK based in large part on a systems level understanding of the process flow. This system level understanding is best expressed in a flowchart. The quality community may be able to adopt this structure and thereby reduce cost while maintaining and enhancing quality. The quality community should attempt to flowchart the systems level quality process before beginning substantive testing. This theory needs to be applied in several trial cases to prove or disprove this hypothesis

Shape memory polymer nanocomposites for application of multiple-field active disassembly: experiment and simulation.

Science.gov (United States)

Carrell, John; Zhang, Hong-Chao; Wang, Shiren; Tate, Derrick

2013-11-19

Active disassembly (AD) uses innovative materials that can perform a designed disassembly action by the application of an external field. AD provides improvements over current disassembly processes by limiting machine or manual labor and enabling batch processing for end-of-life products. With improved disassembly operations, more reuse of components and purer recycling streams may be seen. One problem with AD, however, has been with the single-field actuation because of the probability of accidental disassembly. This presentation will discuss the application of shape memory polymer (SMP) nanocomposites in a new AD process. This novel AD process requires multiple-field actuation of the SMP nanocomposite fastener. In the analysis of this AD process, thermal and magnetic field tests were performed on the SMP nanocomposite. From these tests, finite-element analysis was performed to model and simulate the multiple-field AD process. The results of the simulations provide performance variables for the AD process and show a better performance time for the SMP nanocomposite fastener than for a comparable SMP fastener.

The Falls City Engineers: A History of the Louisville District U.S. Army Corps of Engineers 1984-2004

Science.gov (United States)

2008-01-01

been undertaken nor completed. Contract administrators Jon Fleshman and Vanessa Whitworth together with Carol Labashosky and Todd Hornback of the...Frick, Doug Shelton, Lee Anne Devine, Robert Willis, Eugene Dowell, Charles Decker, Robert Van Hoff, Steve Rager, and Ron Waller, plus the crews at...and able.28 Edward Hoagland, the resource manager, handled the transition. He arranged the transfer of personnel and projects from the Mobile

Environmental Impact Research Program. Osprey Nest Platforms. Section 5.1.6, US Army Corps of Engineers Wildlife Resources Management Manual.

Science.gov (United States)

1986-07-01

34"x 0treated pole, with 101, olts5" min. top diam. 518"x 7" hardwood dowel,6’O set 1- 112" deep, glued TOP VIEW I r 2’-,9 Some as dinam . of pole usedI I...added strength ; these are described in the section entitled Tripod Support. Pole supports. Two designs are suggested for attaching the solid base

shaping-lathe headrig yields solid and molded-flake hardwood products

Science.gov (United States)

Peter Koch; R.A. Caughey

1978-01-01

A shaping-lathe headrig, operated one shift daily, can be used to manufacture hardwood cants to be resawed into pallet shook, one-piece and dowel-laminated crossties, posts and rails, and other solid wood products in lengths from 6 to 9 feet. Residual flakes machined by the headrig supply a three-shift operation in which molded pallets and 4- by 8-foot sheets of...

Benefits of a relational database for computerized management

International Nuclear Information System (INIS)

Shepherd, W.W.

1991-01-01

This paper reports on a computerized relational database which is the basis for a hazardous materials information management system which is comprehensive, effective, flexible and efficient. The system includes product information for Material Safety Data Sheets (MSDSs), labels, shipping, and the environment and is used in Dowell Schlumberger (DS) operations worldwide for a number of programs including planning, training, emergency response and regulatory compliance

Clinical Characteristics of Abutment Teeth with Gingival Discoloration.

Science.gov (United States)

Ristic, Ljubisa; Dakovic, Dragana; Postic, Srdjan; Lazic, Zoran; Bacevic, Miljana; Vucevic, Dragana

2017-04-06

The grey-bluish discoloration of gingiva (known as "amalgam tattoo") does not appear only in the presence of amalgam restorations. It may also be seen in cases of teeth restored with cast dowels and porcelain-fused-to-metal (PFM) restorations. The aim of this article was to determine the clinical characteristics of abutment teeth with gingival discoloration. This research was conducted on 25 patients referred for cast dowel and PFM restorations. These restorations were manufactured from Ni-Cr alloys. Ninety days after cementing the fixed prosthodontic restorations, the abutment teeth (n = 61) were divided into a group with gingival discoloration (GD) (n = 25) and without gingival discoloration (NGD) (n = 36). The control group (CG) comprised the contralateral teeth (n = 61). Plaque index, gingival index, clinical attachment level, and probing depth were assessed before fabrication and also 90 days after cementation of the PFM restorations. The gingival index, clinical attachment level, and probing depths of the abutment teeth that had GD were statistically higher before restoration, in comparison with the abutment teeth in the NGD and control groups. Ninety days after cementation, the abutment teeth with GD had significantly lower gingival indexes and probing depths, compared to the abutment teeth in the NGD group. Both abutment teeth groups (GD and NGD) had significantly higher values of clinical attachment levels when compared to the control group. There were no statistically significant differences in plaque index values between the study groups. The results of this study indicated that impairment of periodontal status of abutment teeth seemed to be related to the presence of gingival discolorations. Therefore, fabrication of fixed prosthodontic restorations requires careful planning and abutment teeth preparation to minimize the occurrence of gingival discolorations. With careful preparation of abutment teeth for cast dowels and crown restorations it may be

A bamboo braced frame system for tropical climates

Directory of Open Access Journals (Sweden)

Echeverria, J.

2014-12-01

Full Text Available A low-cost housing system was developed for use in tropical countries, specifically Haiti, with the aims of minimizing environmental impact (including carbon emissions, maximizing use of local and preferably recycled materials, and using local labor. The housing system integrates low-strength concrete blocks (made using recycled concrete aggregate, an innovative seismically-resistant bamboo frame, earthen plasters, bamboo trusses, and metal deck roofs. The bamboo frame relies on flexural yielding of a short rebar dowel to provide ductile performance at a controlled strength level. The plinth walls below the frame and short rebar dowel protects the bamboo from moisture. The top of a plastic soda bottle is used to protect the rebar from moisture and to seal the base of the bamboo culm, allowing mortar to be introduced into the culm above. This paper focuses on the experimental and analytical results of the flexural yielding of the rebar dowel to establish the structural design of this critical component of the system for resisting wind and seismic loads.En este artículo se presenta un sistema de construcción de viviendas de bajo coste para países tropicales en los cuales existe riesgo sísmico. Los objetivos de este trabajo son generar bajo impacto medioambiental (incluyendo las emisiones de carbono, empleo de materiales locales, preferiblemente reciclados, y mano de obra local. Para esta construcción se han empleado bloques de hormigón de baja resistencia (con agregado reciclado junto con un innovador sistema de pórticos de bambú, botellas de plástico, vigas de bambú y cubiertas de chapa. El comportamiento dúctil de la estructura se garantiza introduciendo una barra de acero en la base del pórtico de bambú. Para proteger el bambú de la humedad, el pórtico se monta sobre un zócalo. Los resultados experimentales y analíticos obtenidos se utilizan para el diseño estructural del sistema frente a cargas de viento y sísmicas.

Heat Loads Due To Small Penetrations In Multilayer Insulation Blankets

Science.gov (United States)

Johnson, W. L.; Heckle, K. W.; E Fesmire, J.

2017-12-01

The main penetrations (supports and piping) through multilayer insulation systems for cryogenic tanks have been previously addressed by heat flow measurements. Smaller penetrations due to fasteners and attachments are now experimentally investigated. The use of small pins or plastic garment tag fasteners to ease the handling and construction of multilayer insulation (MLI) blankets goes back many years. While it has long been understood that penetrations and other discontinuities degrade the performance of the MLI blanket, quantification of this degradation has generally been lumped into gross performance multipliers (often called degradation factors or scale factors). Small penetrations contribute both solid conduction and radiation heat transfer paths through the blanket. The conduction is down the stem of the structural element itself while the radiation is through the hole formed during installation of the pin or fastener. Analytical models were developed in conjunction with MLI perforation theory and Fourier’s Law. Results of the analytical models are compared to experimental testing performed on a 10 layer MLI blanket with approximately 50 small plastic pins penetrating the test specimen. The pins were installed at ∼76-mm spacing inches in both directions to minimize the compounding of thermal effects due to localized compression or lateral heat transfer. The testing was performed using a liquid nitrogen boil-off calorimeter (Cryostat-100) with the standard boundary temperatures of 293 K and 78 K. Results show that the added radiation through the holes is much more significant than the conduction down the fastener. The results are shown to be in agreement with radiation theory for perforated films.

Safety catching device for pipe lines in missile shielding cylinders of nuclear power plants

International Nuclear Information System (INIS)

Hering, S.; Doll, B.

1975-01-01

The safety catching device for pipes in the missile shielding cylinders consists of a flexible steel cable surrounding the pipe in a distance in U-shape. The arrester cable - which works as a spring and is freely movable in all directions - is attached to the cylinder wall. For this, the ends of the cable are primarily fastened to anchor boxes which are then inserted in a stay tube with the same axis as the cable ends. The anchor boxes are fastened to the outer wall of the missile shielding cylinder by anchor bolts and holding plates. (DG/AK) [de

Safety against formation of through cracks of profiled fibre-reinforced cement sheets for roofing

DEFF Research Database (Denmark)

Hansen, Klavs Feilberg; Stang, Birgitte Friis Dela

2009-01-01

  Loads due to wind, snow or traffic on a roof determine the requirements to the strength and stiffness properties of profiled sheets for roofing. Apart from these loads, locked-in stresses can occur due to differences in temperature and moisture strains in the profiled sheets and the wooden laths...... supporting the sheets. These tensile and compressive stresses are induced in the sheets if they are firmly fastened to the laths with fastening screws. The purpose of this investigation was to analyse the safety of the profiled sheets in transmitting these loads without the formation of through cracks...

The Collective-Action Frame and Emergence: A Better Understanding of the Operational Environment

Science.gov (United States)

2013-12-13

upon quotidian associations to sustain the battle , but the latent connections evolve into creative solutions ( Parkinson 2013, 423). The soldier...Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law , no person...5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) MAJ Kurt J. McDowell 5d. PROJECT NUMBER 5e. TASK NUMBER

INVESTIGATION OF THE EFFECTS OF DIFFERENT EDGE JOINT ELEMENTS ON DIAGONAL TENSILE STRENGTH IN FURNITURE EDGE JOINTS

Directory of Open Access Journals (Sweden)

Arif GÜRAY

2002-01-01

Full Text Available In this work, the diagonal tensile strength of furniture edge joints such as wooden dowel, minifix, and alyan screw was investigated in panel-constructed boards for Suntalam and MDF Lam. For this purpose, a diagonal tensile strength test was applied to the 72 samples. According to the results, the maximum diagonal tensile strength was found to be in MDF Lam boards that jointed with alyan screw.

Bracing system of the reflecting sheets making up an insulating pile

International Nuclear Information System (INIS)

Carr, R.W.

1976-01-01

In order to reduce heat and radiation losses, the body of nuclear reactors and the connected pipe work are encased in reflecting and insulating piles of thin spaced sheets of aluminium or stainless steel. These spaced sheets are then encased in thicker and more solid internal and external shells. The piles and shells are generally shaped to follow the contour of the reactor and connected piping. It is therefore necessary to have available a study bracing system to keep the pile intact during the various handling and assembly operations. The fastening system must also exert an effect on the edge of the pile to prevent the sheets making it up from shifting in relation to each other. The description is given of a fastening system that includes an oblong section to be fitted along the edges of the piles up sheets; bracing substantially perpendicular to the oblong section, to space the sheets of the stack in pairs; and a maintaining system, normally perpendicular to the oblong section, to enable the fastener to be clipped to the edge of the sheets by bending it around the edge of each sheet of the pile [fr

A loading/unloading buoy; Laste/losseboeye

Energy Technology Data Exchange (ETDEWEB)

Breivik, K.; Smedal, A.; Syvertsen, K.

1994-10-10

The invention relates to a buoy design for use in the offshore loading or unloading of crude oil in particular. The buoy comprises an outer buoyancy member arranged to be introduced and secured in a submerged downwardly open receiving space in a floating vessel, and a central member which is rotatably mounted in the outer member and is intended for anchoring to the sea bed and arranged for passage of medium between a transfer line which, in operation, is coupled to the lower end of the central member and a tube system on the vessel. The central member is provided with a lower extension body having an outer peripheral portion abutting on and essentially corresponding to the outer periphery of the adjacent end of the outer buoyancy member, and having a lower portion which is downwardly tapering from the outer peripheral portion. A number of fastening means for fastening of the upper ends of anchoring lines for anchoring of the buoy are fastened at intervals along the periphery of the outer peripheral portion of the extension body, and the extension body comprises at least one buoyancy chamber for buoyancy or ballast material. 6 figs.

Characterization and optimization of spiral eddy current coils for in-situ crack detection

Science.gov (United States)

Mandache, Catalin

2018-03-01

In-situ condition-based maintenance is making strides in the aerospace industry and it is seen as an alternative to scheduled, time-based maintenance. With fatigue cracks originating from fastener holes as the main reason for structural failures, embedded eddy current coils are a viable non-invasive solution for their timely detection. The development and potential broad use of these coils are motivated by a few consistent arguments: (i) inspection of structures of complicated geometries and hard to access areas, that often require disassembly, (ii) alternative to regular inspection actions that could introduce inadvertent damage, (iii) for structures that have short inspection intervals, and (iv) for repaired structures where fastener holes contain bushings and prevent further bolt-hole inspections. Since the spiral coils are aiming at detecting radial cracks emanating from the fastener holes, their design parameters should allow for high inductance, low ohmic losses and power requirements, as well as optimal size and high sensitivity to discontinuities. In this study, flexible, surface conformable, spiral eddy current coils are empirically investigated on mock-up specimens, while numerical analysis is performed for their optimization and design improvement.

Wear Improvement of Tools in the Cold Forging Process for Long Hex Flange Nuts.

Science.gov (United States)

Hsia, Shao-Yi; Shih, Po-Yueh

2015-09-25

Cold forging has played a critical role in fasteners and has been widely used in automotive production, manufacturing, aviation and 3C (Computer, Communication, and Consumer electronics). Despite its extensive use in fastener forming and die design, operator experience and trial and error make it subjective and unreliable owing to the difficulty of controlling the development schedule. This study used finite element analysis to establish and simulate wear in automotive repair fastener manufacturing dies based on actual process conditions. The places on a die that wore most quickly were forecast, with the stress levels obtained being substituted into the Archard equation to calculate die wear. A 19.87% improvement in wear optimization occurred by applying the Taguchi quality method to the new design. Additionally, a comparison of actual manufacturing data to simulations revealed a nut forging size error within 2%, thereby demonstrating the accuracy of this theoretical analysis. Finally, SEM micrographs of the worn surfaces on the upper punch indicate that the primary wear mechanism on the cold forging die for long hex flange nuts was adhesive wear. The results can simplify the development schedule, reduce the number of trials and further enhance production quality and die life.

ENTREPRENEURIAL INNOVATION IN TRADITIONAL WEAVING CRAFTSMEN DESIGNED BATIK FOR IMPROVING THE TOURISM INDUSTRY IN KLATEN

Directory of Open Access Journals (Sweden)

Sri Murni

2011-12-01

Full Text Available The target of this study is to improve skilled knowledge and attitude worker of weave fasten as that self-supporting as according to potency and also opportunity work at industrial company, which is on finally can improve the quality of its life. Special target of this study give the knowledge of entrepreneurship among worker of weave fasten so that have high job ethos and also can yield pre-eminent masterpieces capable to compete in global market. The implementation take place to start 16 July until 23 July 2010, what consist of three phase that is activity early stage cover preparation phase, middle phase of activity which phase execution of training and also final phase of activity covering phase handling of post training. This training assign value added because there is skilled of batik design innovation at weave fastens affecting at make-up of production addition. The next study shall earn to measure effectiveness of “transfer training” on so that will be able to know how far done training can alter behavior of educative participant plunging in corporate world and industrial world and also trying self-supporting.

Determination of the primary technical parameters of the test bench for controlling the temperature of rails and rail bars of continuous welded rail

Directory of Open Access Journals (Sweden)

Tertychnyi Vitalii

2017-01-01

Full Text Available One of the most important factors determining the reliability and safety of operation of the continuous welded rail track is the temperature of the rails. All conditions of laying, repair and maintenance of the track during the entire cycle of rails operation depend on it. The existing rail temperature monitoring method does not take into account a few significant factors and that leads to significant errors in determining the actual temperature of the rail bar. The authors propose a new rail temperature measurement method on a special test bench which maximally simulates possible environmental operating conditions for the rail bars, the profile of the roadway (embankment or cut, as well as the actual spatial latitude and meridian location of the rail slabs. At the bench, the studied rails are fastened with the help of rail braces on half ties, in the ballast bed, with sizes in accordance with the existing reference documents. At the first stage, the most common KB-65 intermediate fastener for the continuous welded rail in Ukraine will be used, while in subsequent stages KPP-5 fastening will be used.

Effect of the simulated periodontal ligament on cast post-and-core removal using an ultrasonic device

Directory of Open Access Journals (Sweden)

Manoel Brito-Junior

2010-10-01

Full Text Available ABSTRACT OBJECTIVE: The aim of this study was to evaluate the effect of simulated periodontal ligament (SPDL on custom cast dowel and core removal by ultrasonic vibration. MATERIAL AND METHODS: Thirty-two human maxillary canines were included in resin cylinders with or without SPDL made from polyether impression material. In order to allow tensile testing, the roots included in resin cylinders with SPDL were fixed to cylinders with two stainless steel wires. Post-holes were prepared by standardizing the length at 8 mm and root canal impressions were made with self-cured resin acrylic. Cast dowel and core sets were fabricated and luted with Panavia F resin cement. Half of the samples were submitted to ultrasonic vibration before the tensile test. Data were analyzed statistically by two-way ANOVA and Tukey's post-hoc tests (p<0.05. RESULTS: The ultrasonic vibration reduced the tensile strength of the samples directly included in resin cylinders. There was no difference between the values, whether or not ultrasonic vibration was used, when the PDL was simulated. However, the presence of SPDL affected the tensile strength values even when no ultrasonic vibration was applied. CONCLUSION: Simulation of PDL has an effect on both ultrasonic vibration and tensile testing.

IMPROVEMENT OF WELDED CONNECTIONS WITH SIDE LAP WELDS BY REDISTRIBUTION OF ALL-WELD METAL ALONG LENGTHS AND CROSS-SECTIONS THEREOF USING MECHANIZED AND ROBOTIC WELDING SYSTEMS

Directory of Open Access Journals (Sweden)

Pavlov Evgeniy Igorevich

2017-05-01

Full Text Available Experimental study of bearing capacity of samples of two series performed by semiautomatic welding in CO2 on the axis, and by robotic welding machine in mixture (CO2 + Ar, is presented. Welds of constant cross section, welds with extended leg on end sections, and welds in the form of two dowels on end sections were performed. Efficiency of pilot samples of the first series (with extended leg on end sections by way of a smooth transition defined by the ratio of weld metal volume to a crushing load reaches 28 % relative to samples with a leg constant as per length. Samples of the first series with an extended leg on end sections also showed efficiency increased to 17 %. According to the second series samples test results, the exceeding of bearing capacity of the samples performed with an extended leg on end sections by 24 % in comparison with the samples with a leg of constant cross section was determined. Samples of the second series performed in the form of two dowels on end sections demonstrated the exceeding of the relative bearing capacity by 42 % in comparison with the samples with a continuous leg of constant cross-section.

Mechanical coupling for a rotor shaft assembly of dissimilar materials

Science.gov (United States)

Shi, Jun [Glastonbury, CT; Bombara, David [New Hartford, CT; Green, Kevin E [Broad Brook, CT; Bird, Connic [Rocky Hill, CT; Holowczak, John [South Windsor, CT

2009-05-05

A mechanical coupling for coupling a ceramic disc member to a metallic shaft includes a first wedge clamp and a second wedge clamp. A fastener engages a threaded end of a tie-bolt to sandwich the ceramic disc between the wedge clamps. An axial spring is positioned between the fastener and the second wedge clamp to apply an axial preload along the longitudinal axis. Another coupling utilizes a rotor shaft end of a metallic rotor shaft as one wedge clamp. Still another coupling includes a solid ceramic rotor disc with a multiple of tie-bolts radially displaced from the longitudinal axis to exert the preload on the solid ceramic rotor disc.

Rotating anode x-ray tube

International Nuclear Information System (INIS)

Hueschen, R.E.; Jens, R.A.

1980-01-01

A solid low thermal conductivity columbium metal stem supports heavy refractory metal x-ray target and adjoins high thermal conductivity rotor hub fastened to rotor with low thermally conductive bearing hub fastened to a shaft journaled for rotation in bearings. The rotor is coated to enhance heat dissipation and the arrangement promotes thermal isolation of the bearings from the hot rotor hub and hot target. The hub is of Mo or Mo based alloy, and hub of Ni based alloy. Specific compositions with additives are detailed. Hub additionally restricts heat flow due to its maximised length and minimised cross-section, the reduced area bosses further restricting surface contact. (author)

Nuclear reactor fuel rod attachment system

International Nuclear Information System (INIS)

Christiansen, D.W.

1983-01-01

The invention involves a technique to quickly, inexpensively and rigidly attach a nuclear reactor fuel rod to a support member. The invention also allows for the repeated non-destructive removal and replacement of the fuel rod. The proposed fuel rod and support member attachment and removal system consists of a locking cap fastened to the fuel rod and a locking strip fastened to the support member or vice versa. The locking cap has two or more opposing fingers shaped to form a socket. The fingers spring back when moved apart and released. The locking strip has an extension shaped to rigidly attach to the socket's body portion

Characterization of Quantum Efficiency and Robustness of Cesium-Based Photocathodes

Science.gov (United States)

2010-01-01

the wiggler magnet configuration in 1951 and later demonstrated (incoherent) millimeter and nanometer radiation; of Robert Phillips, whose...Construction and Status of all Niobium Superconducting Photoinjector at BNL." Particle Accel. Conf. 2003, MOPB010, 92 (2003). 51. J. Smedley et al...emissivity of copper." J. Opt. Soc. Am., 71, 354 (1981). 102. D. H. Dowell, F. K. King, R. E. Kirby, J. F. Schmerge and J. M. Smedley . "In situ cleaning

International Free Electron Laser Conference (15th) Held in The Hague, Netherland on August 23-27, 1993. Book of Abstracts

Science.gov (United States)

1993-08-27

missioning and service for: nology, extending from research and development, design, c( nstruction and El Synchrotron radiation facilities...Experiment Using the Coherent Synchrotron Radiation Emitted From Electron Bunches M. AsaKawa, N. Sakamoto, N. Inoue, T. Yamamoto, K. Mima, S. Nakai, J...Netherlands 12:30 Lunch Session Poster I 14:00 Th3-01 Magnetic Bunching Experiments on ELSA S. Joly, D.H. Dowell, ELSA -FEL Team CEN/SPTN, France Th3-03

Design method for strut-beam connection in hinged frames

OpenAIRE

Cardenal Basté, Joan

2011-01-01

Glulam is almost exclusively the chosen material of timber frame structures. Of those, three-hinged (three-pin) portal frames are incomparably the most common type. Being both statically determinate and stable against horizontal forces in its own plane o er both practical (basic constructive details) and economical bene ts. The design of the haunch allows for various solutions: it can be curved with continuous laminates, nger jointed, jointed with steel dowels and slotted-i...

Magnetic Tomography - Assessing Tie Bar and Dowel Bar Placement Accuracy

Science.gov (United States)

2017-12-01

The Kansas Department of Transportation (KDOT) constructs portland cement concrete pavements (PCCP) for new highway expansions and/or for replacement of existing highway pavement using slip-form paving operations. Typical concrete pavement constructi...

78 FR 35604 - Foreign-Trade Zone (FTZ) 155-Calhoun/Victoria Counties, Texas; Notification of Proposed...

Science.gov (United States)

2013-06-13

...); compressors; fans (blades); turbochargers; air conditioners; heat exchangers; filters; windshield washer..., fasteners; articles of copper (tubing, fittings, cables, washers, screws, gaskets, and seals); articles of...

Probability of detection for bolt hole eddy current in extracted from service aircraft wing structures

Science.gov (United States)

Underhill, P. R.; Uemura, C.; Krause, T. W.

2018-04-01

Fatigue cracks are prone to develop around fasteners found in multi-layer aluminum structures on aging aircraft. Bolt hole eddy current (BHEC) is used for detection of cracks from within bolt holes after fastener removal. In support of qualification towards a target a90/95 (detect 90% of cracks of depth a, 95% of the time) of 0.76 mm (0.030"), a preliminary probability of detection (POD) study was performed to identify those parameters whose variation may keep a bolt hole inspection from attaining its goal. Parameters that were examined included variability in lift-off due to probe type, out-of-round holes, holes with diameters too large to permit surface-contact of the probe and mechanical damage to the holes, including burrs. The study examined the POD for BHEC of corner cracks in unfinished fastener holes extracted from service material. 68 EDM notches were introduced into two specimens of a horizontal stabilizer from a CC-130 Hercules aircraft. The fastener holes were inspected in the unfinished state, simulating potential inspection conditions, by 7 certified inspectors using a manual BHEC setup with an impedance plane display and also with one inspection conducted utilizing a BHEC automated C-Scan apparatus. While the standard detection limit of 1.27 mm (0.050") was achieved, given the a90/95 of 0.97 mm (0.039"), the target 0.76 mm (0.030") was not achieved. The work highlighted a number of areas where there was insufficient information to complete the qualification. Consequently, a number of recommendations were made. These included; development of a specification for minimum probe requirements; criteria for condition of the hole to be inspected, including out-of-roundness and presence of corrosion pits; statement of range of hole sizes; inspection frequency and data display for analysis.

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

Science.gov (United States)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

[Use of seat belts and mobile phone while driving in Florence: trend from 2005 to 2009].

Science.gov (United States)

Lorini, Chiara; Pellegrino, Elettra; Mannocci, Federico; Allodi, Guendalina; Indiani, Laura; Mersi, Anna; Petrioli, Giuseppe; Santini, Maria Grazia; Garofalo, Giorgio; Bonaccorsi, Guglielmo

2012-01-01

to evaluate the trend over time of the use of seat belts by drivers and passengers of cars and vans and the use of hand held mobile phone while driving in Florence from 2005 to 2009. DESIGN, SETTING AND PARTICIPANTS AND MAIN OUTCOME MEASURES: direct observations (58,773 vehicles) have been conducted to detect the use of seat belts by occupants of cars and vans, and the use of mobile phone while driving. It has been carried out correlation analysis between the use of the seat belt by occupants of vehicles and between the simultaneous use of this device and mobile phone while driving.Moreover, it has been carried out time series analysis (ARIMA Box Jenkins) of in the prevalence of the use of seat belts by occupants of vehicles observed, of mobile phone by drivers and the trend of the risk to drive using the mobile phone with unfastened seat belt rather than to drive using the mobile phone with fastened seat belt. seat belts were used on average by 75.7% of drivers, 75.5% of front passengers and 25.1% of rear passengers. The average mobile phone use while driving was 4.5%. Drivers most frequently fasten seat belt if front passengers use it and while they do not use mobile phone. The use of seat belts by drivers and front passengers has not changed over time, whereas the use of mobile phone while driving has significantly increased. The prevalence of using mobile phone with unfastened seat belt rather than to use it with fastened seat belt while driving has significantly decreased over the years, indicating an increase in the use of mobile phone, especially among those who fasten the seat belt. it is necessary to plan and realize stronger interventions in the whole area.

30 CFR 18.32 - Fastenings-additional requirements.

Science.gov (United States)

2010-07-01

... and Design Requirements § 18.32 Fastenings—additional requirements. (a) Bolts, screws, or studs shall...) Lockwashers shall be provided for all bolts, screws, and studs that secure parts of explosion-proof enclosures... conduct explosion tests with standard bolts, nuts, cap screws, or studs substituted for any special high...

A Survey of Fastening Techniques for Shipbuilding

Science.gov (United States)

1973-09-01

40, to temperature by Neoprene aluminum. moisture ab - rubber bondled Also alum- sorption, to 20124-n3 ilum to aluminum aluminum. 301.6 lbs/in ®~ x...n.applicantionrs ahr-lar high aluu g Epox resina strenrgthr in requaired. raeadeig. Boaaodtraas m etnals. alarslics, as ara al glnass anda fiber

Removal and replacement of fuel rods in nuclear fuel assembly

International Nuclear Information System (INIS)

Shallenberger, J.M.; Ferlan, S.J.

1983-01-01

Apparatus for replacing components of a nuclear fuel assembly stored in a pit under about 10 m. of water. The fuel assembly is secured in a container which is rotatable from the upright position to an inverted position in which the bottom nozzle is upward. The bottom nozzle plate is disconnected from the control-rod thimbles by means of a cutter for severing the welds. To guide and provide lateral support for the cutter a fixture including bushings is provided, each encircling a screw fastener and sealing the region around a screw fastener to trap the chips from the severed weld. Chips adhering to the cutter are removed by a suction tube of an eductor. (author)

Linear and/or curvilinear rail mount system

Science.gov (United States)

Thomas, Jackie D. (Inventor); Harris, Lawanna L. (Inventor)

2012-01-01

One or more linear and/or curvilinear mounting rails are coupled to a structure. Each mounting rail defines a channel and at least one cartridge assembly is engaged in the channel. Each cartridge assembly includes a housing that slides within the channel. The housing defines a curvilinearly-shaped recess longitudinally aligned with the channel when the housing is in engagement therewith. The cartridge assembly also includes a cleat fitted in the recess for sliding engagement therealong. The cleat can be coupled to a fastener that passes through the mounting rail and the housing when the housing is so-engaged in the channel. The cleat is positioned in the recess by a position of the fastener.

Nuclear reactor pressure vessel with an inner metal coating covered with a high temperature resistant thermal insulator

International Nuclear Information System (INIS)

1974-01-01

The thermal insulator covering the metal coating of a reactor vessel is designed for resisting high temperatures. It comprises one or several porous layers of ceramic fibers or of stacked metal foils, covered with a layer of bricks or ceramic tiles. The latter are fixed in position by fasteners comprising pins fixed to the coating and passing through said porous layers and fasteners (nut or bolts) for individually fixing the bricks to said pins, whereas ceramic plugs mounted on said bricks or tiles provide for the thermal insulation of the pins and of the nuts or bolts; such a thermal insulation can be applied to high-temperature reactors or to fast reactors [fr

Remote tool development at the Interim Examination and Maintenance (IEM) cell

International Nuclear Information System (INIS)

Kalk, J.J.

1986-07-01

Tightening fasteners remotely in a hot cell can be a very exasperating experience. In many places, viewing is difficult and work sometimes must be done using mirrors and/or cameras for viewing. If electromechanical manipulators are used, the operator has no ''feel'', which often can result in broken equipment. At the Interim Examination and Maintenance (IEM) Cell, where reactor components from the Fast Flux Test Facility (FFTF) are disassembled, several tools have been developed for tightening fasteners under these conditions. The philosophy used for this tool development is to use inexpensive commercially available tools with minimal modification for in-cell use. This philosophy was adopted after spending several years unsuccessfully trying to develop a special electric impact wrench

Simplified computational methods for elastic and elastic-plastic fracture problems

Science.gov (United States)

Atluri, Satya N.

1992-01-01

An overview is given of some of the recent (1984-1991) developments in computational/analytical methods in the mechanics of fractures. Topics covered include analytical solutions for elliptical or circular cracks embedded in isotropic or transversely isotropic solids, with crack faces being subjected to arbitrary tractions; finite element or boundary element alternating methods for two or three dimensional crack problems; a 'direct stiffness' method for stiffened panels with flexible fasteners and with multiple cracks; multiple site damage near a row of fastener holes; an analysis of cracks with bonded repair patches; methods for the generation of weight functions for two and three dimensional crack problems; and domain-integral methods for elastic-plastic or inelastic crack mechanics.

Control of aperture closure during reach-to-grasp movements in Parkinson's disease.

Science.gov (United States)

Rand, M K; Smiley-Oyen, A L; Shimansky, Y P; Bloedel, J R; Stelmach, G E

2006-01-01

This study examined whether the pattern of coordination between arm-reaching toward an object (hand transport) and the initiation of aperture closure for grasping is different between PD patients and healthy individuals, and whether that pattern is affected by the necessity to quickly adjust the reach-to-grasp movement in response to an unexpected shift of target location. Subjects reached for and grasped a vertical dowel, the location of which was indicated by illuminating one of the three dowels placed on a horizontal plane. In control conditions, target location was fixed during the trial. In perturbation conditions, target location was shifted instantaneously by switching the illumination to a different dowel during the reach. The hand distance from the target at which the subject initiated aperture closure (aperture closure distance) was similar for both the control and perturbation conditions within each group of subjects. However, that distance was significantly closer to the target in the PD group than in the control group. The timing of aperture closure initiation varied considerably across the trials in both groups of subjects. In contrast, aperture closure distance was relatively invariant, suggesting that aperture closure initiation was determined by spatial parameters of arm kinematics rather than temporal parameters. The linear regression analysis of aperture closure distance showed that the distance was highly predictable based on the following three parameters: the amplitude of maximum grip aperture, hand velocity, and hand acceleration. This result implies that a control law, the arguments of which include the above parameters, governs the initiation of aperture closure. Further analysis revealed that the control law was very similar between the subject groups under each condition as well as between the control and perturbation conditions for each group. Consequently, the shorter aperture closure distance observed in PD patients apparently is a

Control of aperture closure during reach-to-grasp movements in parkinson’s disease

Science.gov (United States)

Rand, M. K.; Smiley-Oyen, A. L.; Shimansky, Y. P.; Bloedel, J. R.; Stelmach, G. E.

2007-01-01

This study examined whether the pattern of coordination between arm-reaching toward an object (hand transport) and the initiation of aperture closure for grasping is different between PD patients and healthy individuals, and whether that pattern is affected by the necessity to quickly adjust the reach-to-grasp movement in response to an unexpected shift of target location. Subjects reached for and grasped a vertical dowel, the location of which was indicated by illuminating one of the three dowels placed on a horizontal plane. In control conditions, target location was fixed during the trial. In perturbation conditions, target location was shifted instantaneously by switching the illumination to a different dowel during the reach. The hand distance from the target at which the subject initiated aperture closure (aperture closure distance) was similar for both the control and perturbation conditions within each group of subjects. However, that distance was significantly closer to the target in the PD group than in the control group. The timing of aperture closure initiation varied considerably across the trials in both groups of subjects. In contrast, aperture closure distance was relatively invariant, suggesting that aperture closure initiation was determined by spatial parameters of arm kinematics rather than temporal parameters. The linear regression analysis of aperture closure distance showed that the distance was highly predictable based on the following three parameters: the amplitude of maximum grip aperture, hand velocity, and hand acceleration. This result implies that a control law, the arguments of which include the above parameters, governs the initiation of aperture closure. Further analysis revealed that the control law was very similar between the subject groups under each condition as well as between the control and perturbation conditions for each group. Consequently, the shorter aperture closure distance observed in PD patients apparently is a

New River and Phoenix City Streams, Arizona. Overall Master Plan.

Science.gov (United States)

1980-09-01

the south, and the Sierra Estrella to the southwest. Only to the we.st and southeast do the rolling desert plains typical of the metropolitan area...east by the McDowell Mountains; on the south by the South Mountains; on the southwest by the Sierra Estrella Mountains and Buckeye Hills; on the west...northeast, the Usury Mountains to the east, the South Mountains to the south, and the Sierra Estrella to the southwest. Only to the west and

CRAFT

DEFF Research Database (Denmark)

Gammelgaard Nielsen, Anders

2012-01-01

At the Aarhus School of Architecture, Associate Professor Anders Gammelgaard has erected a solid wood construction, based on traditional craftsmanship. The entire structure is made of heavy oak timber that is joined together using the old techniques of tongue and groove and dowels. The motivation......-air museums, as a performing art in front of an audience. In this article the author discusses the importance of craft and craftsmanship in contemporary architecture in relation to its users....

Generalized supersymmetric cosmological term in N=1 supergravity

Energy Technology Data Exchange (ETDEWEB)

Concha, P.K.; Rodríguez, E.K. [Departamento de Física, Universidad de Concepción,Casilla 160-C, Concepción (Chile); Dipartimento di Scienza Applicata e Tecnologia (DISAT), Politecnico di Torino,Corso Duca degli Abruzzi 24, I-10129 Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN) Sezione di Torino,Via Pietro Giuria 1, 10125 Torino (Italy); Salgado, P. [Departamento de Física, Universidad de Concepción,Casilla 160-C, Concepción (Chile)

2015-08-04

An alternative way of introducing the supersymmetric cosmological term in a supergravity theory is presented. We show that the AdS-Lorentz superalgebra allows to construct a geometrical formulation of supergravity containing a generalized supersymmetric cosmological constant. The N=1, D=4 supergravity action is built only from the curvatures of the AdS-Lorentz superalgebra and corresponds to a MacDowell-Mansouri like action. The extension to a generalized AdS-Lorentz superalgebra is also analyzed.

One-fifth-scale and full-scale fuel element rocking tests

International Nuclear Information System (INIS)

Nau, P.V.; Olsen, B.E.

1978-06-01

Using 1 / 5 -scale and 1 / 1 -scale (prototype H451) fuel elements, one, two, or three stacked elements on a clamped base element were rocked from an initial release position. Relative displacement, rock-down loads, and dowel pin shear forces were measured. A scaled comparison between 1 / 5 -scale and 1 / 1 -scale results was made to evaluate the model scaling laws, and an error analysis was performed to assess the accuracy and usefulness of the test data

An Aversion to Risk; A Warning from the Past

Science.gov (United States)

2014-06-02

Given the unlikely sudden appearance of a 20 Richard E. Neustadt and Ernest R . May, Thinking in Time: The Uses of History for Decision-Makers (New...for 2001, as McClellan’s Peninsula Campaign plan had 3 Stewart, American Military History Volume II, 468-470. 4 Ibid., 481. s Michael R . Gordon and... bedridden again due to illness.41 June 8, 1862: Having failed to subdue Jackson in the Shenandoah Valley, Halleck ordered McDowell to attack

Evaluation of Precast Panels for Airfield Pavement Repair. Phase 1: System Optimization and Test Section Construction

Science.gov (United States)

2013-06-01

provided the most eccentric loading. Configurations with multiple wheel loads on the panel at one time were converted to a composite eccentric load at...Bearing capacity (safety factor), lb/in.2 Type Considered Main gear wheels considered load, kip Eccentricity from center x, in. y, in...dimensions were typically 12 ft x 12 ft x 10 in. with three 1.5-in.-diameter dowel bars cast in the wheel paths to ensure load transfer across the joints

RESTRICTIVE CARDIOMYOPATHY AND SECONDARY CONGESTIVE HEART FAILURE IN A MCDOWELL'S CARPET PYTHON (MORELIA SPILOTA MCDOWELLI).

Science.gov (United States)

Schilliger, Lionel; Chetboul, Valérie; Damoiseaux, Cécile; Nicolier, Alexandra

2016-12-01

Echocardiography is an established and noninvasive diagnostic tool used in herpetologic cardiology. Various cardiac lesions have been previously described in reptiles with the exception of restrictive cardiomyopathy. In this case report, restrictive cardiomyopathy and congestive heart failure associated with left atrial and sinus venosus dilation were diagnosed in a 2-yr-old captive lethargic McDowell's carpet python ( Morelia spilota mcdowelli), based on echocardiographic, Doppler, and histopathologic examinations. This cardiomyopathy was also associated with thrombosis within the sinus venosus.

Thermo-mechanical cyclic testing of carbon-carbon primary structure for an SSTO vehicle

Science.gov (United States)

Croop, Harold C.; Leger, Kenneth B.; Lowndes, Holland B.; Hahn, Steven E.; Barthel, Chris A.

1999-01-01

An advanced carbon-carbon structural component is being experimentally evaluated for use as primary load carrying structure for future single-stage-to-orbit (SSTO) vehicles. The component is a wing torque box section featuring an advanced, three-spar design. This design features 3D-woven, angle-interlock skins, 3D integrally woven spar webs and caps, oxidation inhibited matrix, chemical vapor deposited (CVD) oxidation protection coating, and ceramic matrix composite fasteners. The box spar caps are nested into the skins which, when processed together through the carbon-carbon processing cycle, resulted in monolithic box halves. The box half sections were then joined at the spar web intersections using ceramic matrix composite fasteners. This method of fabrication eliminated fasteners through both the upper and lower skins. Development of the carbon-carbon wing box structure was accomplished in a four phase design and fabrication effort, conducted by Boeing, Information, Space and Defense Systems, Seattle, WA, under contract to the Air Force Research Laboratory (AFRL). The box is now set up for testing and will soon begin cyclic loads testing in the AFRL Structural Test Facility at Wright-Patterson Air Force Base (WPAFB), OH. This paper discusses the latest test setup accomplishments and the results of the pre-cyclic loads testing performed to date.

A review on the technical basis for ACI 349 code revision to anchorage criteria

International Nuclear Information System (INIS)

Lee, N. H.; You, S. H.

1999-01-01

Anchors are widely used to attach structural and nonstructural elements to concrete in nuclear power plant construction. Anchorage to concrete in nuclear-related structure plant has been designed per ACI 349-90 Appendix B. However, a new criteria for anchorage based on the concrete capacity design(CCD) approach is ready for publication under the normal publication procedures by ACI 349 Code Committee. Both design procedures(ACI 349-90 and ACI 349-New) show rather different concrete capacities. Earlier comparable studies show that the CCD method is a more reliable predictor of concrete breakout than the 45-degree cone method(ACI 349-90), hence the CCD method adopted by ACI 349-New Code has been recommended. The philosophy of the current code is to design ductile fastenings, which requires a limit to guard against brittle concrete failure. On the other hand, the new code requires calculations for the concrete breakout strength, pullout strength, side-face blowout strength of fastener in tension, and concrete breakout strength, pryout strength of fastener in shear. Therefore, the new code can accurately predict the concrete failure capacity for different behavior of the anchorage system. In this review, the provisions of ACI 349-90 and ACI 349-New are compared to show the major differences with emphasis on the concrete breakout capacity

SONATINA-2V: a computer program for seismic analysis of the two-dimensional vertical slice HTGR core

International Nuclear Information System (INIS)

Ikushima, Takeshi

1982-07-01

A computer program SONATINA-2V has been developed for predicting the behavior of a two-dimensional vertical slice HTGR core under seismic excitation. SONATINA-2V is a general two-dimensional computer program capable of analyzing the vertical slice HTGR core with the permanent side reflector blocks and its restraint structures. In the analytical model, each block is treated as rigid body and is restrained by dowel pins which restrict relative horizontal movement but allow vertical and rocking motions between upper and lower blocks. Coulomb friction is taken into account between blocks and between dowel pin and hole. A spring dashpot model is used for the collision process between adjacent blocks. The core support structure is represented by a single block. The computer program SONATINA-2V is capable of analyzing the core behavior for an excitation input applied simultaneously to both vertical and horizontal directions. Analytical results obtained from SONATINA-2V are compared with experimental results and are found to be in good agreement. The computer program can thus be used to predict with a good accuracy the behavior of the HTGR core under seismic excitation. In the present report are given, the theoretical formulation of the analytical model, a user's manual to describe the input and output format, and sample problems. (author)

Landfill to Learning Facility

Science.gov (United States)

Venner, Laura

2008-05-01

Engaging "K-to-Gray” audiences (children, families, and older adults) in scientific exploration and discovery is the main goal of the NJMC Center for Environmental and Scientific Education and the William D. McDowell Observatory located in Lyndhurst, NJ. Perched atop a closed and reclaimed municipal solid waste landfill, our new LEED - certified building (certification pending) and William D. McDowell observatory will bring hands-on scientific experiences to the 25,000 students and 3,000 adults that visit our site from the NY/NJ region each year. Our programs adhere to the New Jersey Core Curriculum Content Standards and are modified for accessibility for the underserved communities that visit us, specifically those individuals that have mobility, sensory, and/or cognitive ability differences. The programs are conducted in a classroom setting and are designed to nourish the individual's inquisitive nature and provide an opportunity to function as a scientist by, making observations, performing experiments and recording data. We have an $850,000, three year NSF grant that targets adults with disabilities and older adults with age related limitations in vision, hearing, cognition and/or mobility. From dip netting in the marsh to astronomical investigation of the cosmos, the MEC/CESE remains committed to reaching the largest audience possible and leaving them with a truly exceptional scientific experience that serves to educate and inspire.

A maneuver for improved positioning of a tourniquet in the obese patient.

Science.gov (United States)

Krackow, K A

1982-08-01

Proximal positioning of an arterial tourniquet will be greatly facilitated by having an assistant firmly draw the skin and subcutaneous tissue distally prior to positioning the cast padding and tourniquet. This simple maneuver is clearly not part of current practice or training, despite the simplicity and effectiveness. Excessive tourniquet tightening should be avoided prior to fixing the Velcro fasteners, a practice which is commonly employed and is not only ineffective in maintaining proximal tourniquet positioning, but also deleterious in that it creates a "venous tourniquet" effect. Loosening of the restraining adhesive tapes and unnecessary traction of adhesive tape on sensitive skin can be avoided by bringing the extremity to its resting position before fastening the tape proximal to the tourniquet.

Compact Low Frequency Radio Antenna

Science.gov (United States)

Punnoose, Ratish J.

2008-11-11

An antenna is disclosed that comprises a pair of conductive, orthogonal arches and a pair of conductive annular sector plates, wherein adjacent legs of each arch are fastened to one of the annular sector plates and the opposite adjacent pair of legs is fastened to the remaining annular sector plate. The entire antenna structure is spaced apart from a conductive ground plane by a thin dielectric medium. The antenna is driven by a feed conduit passing through the conductive ground plane and dielectric medium and attached to one of the annular sector plates, wherein the two orthogonal arched act as a pair of crossed dipole elements. This arrangement of elements provides a radiation pattern that is largely omni-directional above the horizon.

Mechanical alignment of substrates to a mask

Science.gov (United States)

Webb, Aaron P.; Carlson, Charles T.; Honan, Michael; Amato, Luigi G.; Grant, Christopher Neil; Strassner, James D.

2016-11-08

A plurality of masks is attached to the underside of a mask frame. This attachment is made such that each mask can independently move relative to the mask frame in three directions. This relative movement allows each mask to adjust its position to align with respective alignment pins disposed on a working surface. In one embodiment, each mask is attached to the mask frame using fasteners, where the fasteners have a shaft with a diameter smaller than the diameter of the mounting hole disposed on the mask. A bias element may be used to allow relative movement between the mask and the mask frame in the vertical direction. Each mask may also have kinematic features to mate with the respective alignment pins on the working surface.

Development of Live-working Robot for Power Transmission Lines

Science.gov (United States)

Yan, Yu; Liu, Xiaqing; Ren, Chengxian; Li, Jinliang; Li, Hui

2017-07-01

Dream-I, the first reconfigurable live-working robot for power transmission lines successfully developed in China, has the functions of autonomous walking on lines and accurately positioning. This paper firstly described operation task and object of the robot; then designed a general platform, an insulator replacement end and a drainage plate bolt fastening end of the robot, presented a control system of the robot, and performed simulation analysis on operation plan of the robot; and finally completed electrical field withstand voltage tests in a high voltage hall as well as online test and trial on actual lines. Experimental results show that by replacing ends of manipulators, the robot can fulfill operation tasks of live replacement of suspension insulators and live drainage plate bolt fastening.

Menstruation in Ulysses.

Science.gov (United States)

Mullin, Katherine

2008-01-01

This article investigates James Joyce's fascination with a wide variety of medical texts, sexual folklores, religious beliefs, and persistent superstitions about menstruation. That fascination finds its way into Ulysses, which draws upon a number of intertexts to inform a curiosity about the female body most strikingly articulated by Bloom, Molly, and Gerty MacDowell. These intertexts are not simply imported into the novel but are dismantled and interrogated, as Joyce exposes, rather than endorses, clichés of essential femininity.

Influenza Pandemic Infrastructure Response in Thailand

Centers for Disease Control (CDC) Podcasts

2009-03-05

Influenza viruses change antigenic properties, or drift, every year and they create seasonal outbreaks. Occasionally, influenza viruses change in a major way, called a “shift." If an influenza virus shifts, the entire human population is susceptible to the new influenza virus, creating the potential for a pandemic. On this podcast, CDC's Dr. Scott Dowell discusses responding to an influenza pandemic.  Created: 3/5/2009 by Emerging Infectious Diseases.   Date Released: 3/5/2009.

The hydraulic lifting system for the main magnets of CYCIAE-30 cyclotron

CERN Document Server

Zhao Zhen Lu; Chen Rong Fan; Chu Cheng Jie

2002-01-01

The oil-line structure, control system and their working principles of the hydraulic lifting system for the main magnets of CYCIAE-30 cyclotron are introduced. The six years practice proves that the specification of the system matches the requirements: the oil cylinder maximum stroke of 850 mm, the eight slot positioning dowels repositioning accuracy of +-0.01 mm, the two oil cylinders moving in step accuracy of 5-10 mm. The system is safe, reliable and easy to be operated

75 FR 34426 - Notice of Petitions by Firms for Determination of Eligibility To Apply for Trade Adjustment...

Science.gov (United States)

2010-06-17

..., WI 53186. latching, u-frame, actuators, high speed, tubular and valve solenoids. Valley Fastener... Gifts, LLC........ 5465 Woodbine Avenue, 6/7/2010 The firm produces laser cut replicas of North, SC...

21 CFR 878.3750 - External prosthesis adhesive.

Science.gov (United States)

2010-04-01

... used to fasten to the body an external aesthetic restoration prosthesis, such as an artificial nose. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in...

Stationary Tether Device for Buoy Apparatus and System for Using

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — A rigid, neutrally buoyant hydrodynamicaly-faired tether and associated fastening hardware that loosely holds a bathymetric float at a predetermined distance from a...

Track Loading Vehicle - TLV

Data.gov (United States)

Federal Laboratory Consortium — The TLV is designed to apply forces close to the strength limits of the rails and other track structure components, such as ties, rail fasteners, and ballast, while...

29 CFR 1917.119 - Portable ladders.

Science.gov (United States)

2010-07-01

... Requirements for Portable Reinforced Plastic Ladders (d) Standards for job-made portable ladders. Job-made... usage. (1) Ladders made by fastening rungs or devices across a single rail are prohibited. (2) Ladders...

Tools and their uses

CERN Document Server

1973-01-01

Teaches names, general uses, and correct operation of all basic hand and power tools, fasteners, and measuring devices you are likely to need. Also, grinding, metal cutting, soldering, and more. 329 illustrations.

Ultrasonic extensometer measures bolt preload

Science.gov (United States)

Daniels, C. M., Jr.

1978-01-01

Extensometer using ultrasonic pulse reflections to measure elongations in tightened belts and studs is much more accurate than conventional torque wrenches in application of specified preload to bolts and other threaded fasteners.

Analysis of interlocking performances on non-oriented electrical steels

Science.gov (United States)

Liu, Li-Hsiang; Liu, Lee-Cheng

2018-05-01

In order to reduce energy loss in motor, applications of high-efficiency non-oriented electrical steel sheets and optimal laminating process are both important elements. The motor core loss deterioration is influenced by a number of factors, such as flux distribution, stress and strain, space harmonics, temperature, and short circuits between lamination. In conventional clamping method, steel sheets are laminated via interlocking or welding in general manner. The measured energy loss by welding was much larger than that by interlocking. Therefore, interlocking is well known and usually employed with benefit of easy conducting. The protuberance shapes affected the fastening strength. Generally, the intensity of rectangular type is stronger than the circular counterparts. However, the circular interlocking has better magnetic characteristics. To clarify the method effectiveness, interlocking performances regarding fastened strength and magnetic deterioration by lamination were investigated. The key parameters of protuberance shape and forming depth were designed. Precisely manufacturing operation was applied to avoid interlocking failure. Magnetic properties largely influenced by clamping method are crucial to minimizing the magnetic deterioration during laminating procedure. Several experiments for various processing conditions were undertaken, and the quantification results showed the rectangular interlocking had better fastened strength but worsened iron loss comparing with the circular arrangement. To acquire the comprehensive mechanical and electrical identities for electrical steel lamination, deliberate producing conditions regarding minimizing the magnetic deterioration should be adopted prudently.

Starting manufacturing phase of ITER upper ports

Energy Technology Data Exchange (ETDEWEB)

Utin, Yuri, E-mail: yuri.utin@iter.org [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Fabritsiev, Sergey [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Giraud, Benoit; Guirao, Julio [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Koenig, Werner [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Kedrov, Igor; Kuzmin, Evgeny [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Levesy, Bruno; Martinez, Jean-Marc [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Prebeck, Markus [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Privalova, Elena [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Ranzinger, Franz [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Savrukhin, Petr [Russian Federation ITER Domestic Agency, Kurchatov sq.1, 123182 Moscow (Russian Federation); Schiller, Thomas [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); and others

2015-10-15

Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

Starting manufacturing phase of ITER upper ports

International Nuclear Information System (INIS)

Utin, Yuri; Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James; Fabritsiev, Sergey; Giraud, Benoit; Guirao, Julio; Koenig, Werner; Kedrov, Igor; Kuzmin, Evgeny; Levesy, Bruno; Martinez, Jean-Marc; Prebeck, Markus; Privalova, Elena; Ranzinger, Franz; Savrukhin, Petr; Schiller, Thomas

2015-01-01

Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

76 FR 61655 - Definition of Part 15 Auditory Assistance Device

Science.gov (United States)

2011-10-05

... hand deliveries must be held together with rubber bands or fasteners. Any envelopes and boxes must be... infrared light waves to specialized receivers used by listeners to enhance the reception of speech. By...

A simplified technique for nasoendotracheal tube immobilization.

OpenAIRE

Berardo, N.; Leban, S. G.; Williams, F. A.

1989-01-01

A simplified technique for immobilization of a nasoendotracheal tube is described in which a wide strap of open cell, hypoallergenic, foam-backed fabric is secured to the patient's head with a Velcro fastener.

Inactivation of West Nile Virus in Serum with Heat, Ionic Detergent, and Reducing Agent for Proteomic Applications (Open Access Publisher’s Version)

Science.gov (United States)

2017-05-19

protocol (McDowell et al., 2013). Briefly, 5 μl of each inactivated serum sample was added to 200 μl 8 M urea /0.1 M Tris-HCl pH 8.5 and filtered...clarified or low complexity sample types such as urine , oral fluid, cerebrospinal fluid, swab material resuspended in viral transport media, cell culture...RNA synthesis and replication. Curr. Opin. Virol. 9, 74–83. Singh, R., Lamoureux, G.V., Lees, W.J., Whitesides, G.M., 1995. Reagents for rapid re

Identification of the First Chinese Cases of H1N1 Flu

Centers for Disease Control (CDC) Podcasts

In this podcast, Dr. Scott Dowell discusses the first cases of the new H1N1 influenza virus in China in May 2009, which occurred in three students who had been studying in North America during the early days of the pandemic and returned home to visit their friends and family. Chinese health officials acted swiftly to investigate and determine whether the students had spread their illness to others. The article, which appears in the September 2009 issue of Emerging Infectious Diseases, details what they found.

Tremor - self-care

Science.gov (United States)

... in your day-to-day: Buy clothes with Velcro fasteners instead of buttons or hooks. Cook or ... your tremor. Some of these medicines have side effects. Tell your provider if you have these symptoms ...

77 FR 36428 - Amendment to the International Traffic in Arms Regulations: Definition for “Specially Designed”

Science.gov (United States)

2012-06-19

... Commerce Control List, such as threaded fasteners (e.g., screws, bolts, nuts, nut plates, studs, inserts... excluding from control simple or multi-use parts such as springs, bolts, and rivets, and other types of...

Composites of 3D-Printed Polymers and Textile Fabrics*

Science.gov (United States)

Martens, Yasmin; Ehrmann, Andrea

2017-08-01

3D printing belongs to the rapidly emerging technologies of our time. Due to its recent drawback - the technology is relatively slow compared with other primary shaping methods, such as injection molding -, 3D printing is often not used for creating complete large components but to add specific features to existing larger objects. One of the possibilities to create such composites with an additional value consists in combining 3D printed polymers with textile fabrics. Several attempts have been made to enhance the adhesion between both materials, a task which is still challenging for diverse material combinations. Our paper reports about new experiments combining 3D printed embossed designs, snap fasteners and zip fasteners with different textile base materials, showing the possibilities and technical limits of these novel composites.

Evaluation of bolted connections in wood-plastic composites

Science.gov (United States)

Arnandha, Yudhi; Satyarno, Iman; Awaludin, Ali; Irawati, Inggar Septia; Ihsan, Muhamad; Wijanarko, Felyx Biondy; William, Mahdinur, Fardhani, Arfiati

2017-03-01

Wood-plastic composite (WPC) is a relatively new material that consists of sawdust and plastic polymer using the extrusion process. Due to its attributes such as low water content, low maintenance, UV durability and being fungi and termite resistant. Nowadays, WPC has already been produced in Indonesia using sawdust from local wood such as Albizia (Paraserianthes falcataria) and Teak (Tectona grandis). Moreover preliminary studies about the physical and mechanical WPC board from Albizia sawdust and HDPE plastic have been carried out. Based on these studies, WPC has a high shear strength around 25-30 MPa higher than its original wood shear strength. This paper was a part of the research in evaluating WPC as potential sheathing in a shear wall system. Since still little is known about connection behavior in WPC using Indonesian local wood, this study evaluated the connection for both of these two types of wood-plastic composite. WPC board from Albizia sawdust will be projected as shear wall sheathing and WPC stud from Teak sawdust projected to be shear wall frame. For this study, the embedding strength for both WPC was determined according to ASTM D 5764 standard, using two types of bolts (stainless bolt and standard bolt) with several diameters as variation (6 mm, 8 mm, 10 and 12 mm). Hence, dowel-bearing test under fastened condition conducted accordance to ASTM D5652, hereby the yield strength then compared with the prediction yield strength from European Yield Model (EYM). According to both single and double shear connection, it can be concluded that yield strength from the EYM method tended to under-predict the 5% diameter offset yield than the actual yield strength from the test. The yield strength itself increase with the increase of bolt diameter. For single shear connection, the highest yield strength was 12 mm standard bolt around 9732 N, slightly higher than stainless bolt around 9393 N. Whereby for double shear connection, the highest yield strength was

14 CFR 135.177 - Emergency equipment requirements for aircraft having a passenger seating configuration of more...

Science.gov (United States)

2010-01-01

... axe carried so as to be accessible to the crew but inaccessible to passengers during normal operations... belts must be fastened. The signs must be constructed so that they can be turned on during any movement...

76 FR 26242 - Paper Clips From the People's Republic of China: Final Results of Expedited Sunset Review of...

Science.gov (United States)

2011-05-06

... order are plastic and vinyl covered paper clips, butterfly clips, binder clips, or other paper fasteners... order is revoked. Parties can obtain a public copy of the I&D Memo from the Central Records Unit, room...

A sealed enclosure of the glove box type

International Nuclear Information System (INIS)

Moreels, Pierre.

1974-01-01

The invention relates to a sealed enclosure of the glove-box type. According to the invention, the box-frame comprises: angle-bars having a right-angled cross-section, sealing joints, tightening bars and fastening means [fr

Evaluasi Kuat Tumpu Alat Sambung Baut pada Papan WPC dari Limbah Sengon dan Plastik HDPE

Directory of Open Access Journals (Sweden)

Yudhi Arnandha

2016-12-01

Full Text Available Wood Plastic Composite (WPC is wood based material that been produce by mixing sawdust as main composition and plastic polymer as bonding agent. Nowadays, WPC board already been produced in Indonesia using Sengon sawdust and recycle HDPE plastic. Sengon sawdust was used as WPC since its availability from plywood production waste, moreover HDPE plastic considered had higher strength and more rigid than PET plastic. WPC occasionally being used as non structural material, moreover from previous study about mechanical properties of WPC, it was found that WPC Sengon has high shear strength around 25 – 30 MPa. These lead that WPC Sengon had a potential used as shear wall sheathing, thus additional research need to be conducted in order to study the type of bolt and diameter of the bolt can be used for these shear wall. This study aimed to investigate the dowel bearing of bolt using full hole method based on ASTM D5764 with type and bolt diameter as specimen variation. Two types of bolt were used in this study; stainless bolt and standard bolt with diameter each of 6 mm, 8 mm, 10 mm and 12 mm. According to ANOVA, there was insignificant result between stainless bolt and standard one, but there was significant result based on diameter of the bolt. Hereafter, it can be recommended the used of 10 mm diameter of bolt for structural purpose with dowel bearing strength around 67 – 70 MPa.

Personal professional indemnity and contractual issues for trainees in obstetrics and gynaecology.

Science.gov (United States)

Chatterjee, J; Datta, S; Butt, S; Harpwood, V

2013-02-01

Over the last few decades, more healthcare professionals have faced investigation into complaints about medical care and healthcare outcomes (Department of Health 2003). With increasing medical negligence cases being brought against doctors, it is time to carefully consider the implications of such actions to ensure appropriate safeguards (Ferner and McDowell 2006). At a time when the culture of 'no win, no fee' is rampant, the jobbing frontline doctor is on the back-foot trying to untangle the legalities of a malpractice claim (Ferner and McDowell 2006). Reassuringly, the numbers of doctors referred to the GMC or having to face legal procedures or claims for compensation are still very small (National Audit Office 2001). An essential issue for all doctors is having appropriate indemnity cover in the event that their practice is challenged. The opt-out for the European Working Time Regulations (EWTR) has caused further confusion as to what is covered for junior doctors by individual indemnity policies and the employer's liability scheme. Recently, the RCOG Trainees committee and the BMA Junior Doctors Association issued a joint advice regarding this issue (RCOG 2010). In this paper, we consider the differences in cover provided by the employer's liability scheme, individual professional indemnity schemes and the role of professional bodies. We also seek to clarify the understanding of these surrounding EWTR and the voluntary opt-out clause and provide up-to-date information on medico-legal issues and protection schemes regarding legal liabilities.

Environmentally Friendly Anticorrosion Coating for High Strength Fasteners

Science.gov (United States)

2011-01-01

electroplated coatings followed by a hexavalent chrome rinse. The environmental and health hazards associated with cadmium and hexavalent chromium are...have been used with cadmium (Cd) electroplated coatings, followed by a hexavalent chromium (Cr6+) rinse. The environmental and human health hazards...followed by a hexavalent chromium (Cr6+) rinse. The environmental and human health hazards associated with both cadmium and chromates are well

Fastening Transfer of Technology Through the Franchise Agreement

OpenAIRE

Asikin, Zainal

2014-01-01

The major improvement of franchise practices in Indonesian within the last 10 (ten) years has speeded to many region. Yet the government and local government under informed about the exact concept and regulation of franchise. Therefore this research meant to find out the concept of franchise and how the government regulate franchise agreement and its relation with transfer of technology. This research in a normative research as a way to depth study legal norms in various primary and secondary...

30 CFR 18.31 - Enclosures-joints and fastenings.

Science.gov (United States)

2010-07-01

... used, it refers to a machine bolt or a cap screw, and for either of these studs may be substituted...″ 0.006″ 0.006″ Maximum bolt 7,8 spacing; joints all in one plane (16) (16) (16) Maximum bolt spacing; joints, portions of which are in different planes (9) (9) (9) Minimum diameter of bolt (without regard to...

Magnetic Resonance Imaging (MRI) -- Head

Medline Plus

Full Text Available ... metal in your body. Guidelines about eating and drinking before your exam vary between facilities. Unless you ... has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with the specific ...

MRI of the Chest

Medline Plus

Full Text Available ... metal in your body. Guidelines about eating and drinking before your exam vary between facilities. Unless you ... has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with the specific ...

Children's (Pediatric) Magnetic Resonance Imaging

Medline Plus

Full Text Available ... has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with the specific ... instructions for your child about not eating or drinking several hours prior to sedation and the examination. ...

Load environment of rail joint bars -- phase II, joint bar service environment and fatigue analysis.

Science.gov (United States)

2014-07-01

Detailed analysis of measured bending strains shows that the foundation deflections have the most significant effect on the : magnitude of strains. All other factors, such as track type, track geometry, and fastening systems, have a less significant ...

MRI of the Chest

Medline Plus

Full Text Available ... devices or metal in your body. Guidelines about eating and drinking before your exam vary between facilities. ... fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with ...

Magnetic Resonance Imaging (MRI) -- Head

Medline Plus

Full Text Available ... devices or metal in your body. Guidelines about eating and drinking before your exam vary between facilities. ... fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with ...

Children's (Pediatric) Magnetic Resonance Imaging

Medline Plus

Full Text Available ... is loose-fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam ... risk to the average patient when appropriate safety guidelines are followed. If sedation is used, there are ...

MRI of the Chest

Medline Plus

Full Text Available ... have any devices or metal in your body. Guidelines about eating and drinking before your exam vary ... is loose-fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam ...

Magnetic Resonance Imaging (MRI) -- Head

Medline Plus

Full Text Available ... have any devices or metal in your body. Guidelines about eating and drinking before your exam vary ... is loose-fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam ...

Children's (Pediatric) Magnetic Resonance Imaging

Medline Plus

Full Text Available ... fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with ... be given instructions for your child about not eating or drinking several hours prior to sedation and ...

Fronteira, fusão, filme: um toque

Directory of Open Access Journals (Sweden)

Tunico Amancio

2010-12-01

Full Text Available Considered the first co-production between MERCOSUR countries, "The touch of the Oboe", a film by Claudio MacDowell, suffers from some sort of vagueness that shows off the difficulties of a complete commercial and cultural movie exchange between Brazil's neighbor countries. Even bolstered with powerful traditions, the productive associative project of this cinematic realization emblematizes an economical, symbolical and historical imbalance which still prevails among the countries of the Southern Common Market. The text notes some of these tensions, marked by the relationship between cinema and literature.

Human analog tests of the sixth stage of object permanence.

Science.gov (United States)

Heishman, M; Conant, M; Pasnak, R

1995-06-01

Two adult cats were tested on multiple invisible displacement. A dowel was established as a secondary reinforcer and hidden in a manner similar to that used to assess the culmination of sensorimotor intelligence in human infants. Three other cats were tested on single invisible displacement, a simpler version of the task. For human infants, this task is used to assess the beginning of mental representation in the sixth and last stage of sensorimotor intelligence. The cats' searches on these tasks were consistent with representation of an unsensed object and fully developed sensorimotor intelligence.

[Comparative study of retention of a Zn phosphate cement and 4-META].

Science.gov (United States)

Maroto Garcia, J

1990-12-01

The recent appearance, in the market of the supercements, suggest to us, news concepts of retention-adhesion, of our preparations, that they are going to put in to the mouth. Between his applications, we have the cementation of crowns, post or dowels, adhesive-prosthesis, and inlays. According to the manufactures, the long duration of the bond power, his great physiques properties, and his easy management, gives to this products a good conditions, to use in the mouth. The present report to prove in vitro, the retentive capacity on the dentine without treatment, and metal.

Equations of motion for a rotor blade, including gravity, pitch action and rotor speed variations

DEFF Research Database (Denmark)

Kallesøe, Bjarne Skovmose

2007-01-01

This paper extends Hodges-Dowell's partial differential equations of blade motion, by including the effects from gravity, pitch action and varying rotor speed. New equations describing the pitch action and rotor speeds are also derived. The physical interpretation of the individual terms...... in the equations is discussed. The partial differential equations of motion are approximated by ordinary differential equations of motion using an assumed mode method. The ordinary differential equations are used to simulate a sudden pitch change of a rotating blade. This work is a part of a project on pitch blade...

A field- and laboratory-based quantitative analysis of alluvium: Relating analytical results to TIMS data

Science.gov (United States)

Wenrich, Melissa L.; Hamilton, Victoria E.; Christensen, Philip R.

1995-01-01

Thermal Infrared Multispectral Scanner (TIMS) data were acquired over the McDowell Mountains northeast of Scottsdale, Arizona during August 1994. The raw data were processed to emphasize lithologic differences using a decorrelation stretch and assigning bands 5, 3, and 1 to red, green, and blue, respectively. Processed data of alluvium flanking the mountains exhibit moderate color variation. The objective of this study was to determine, using a quantitative approach, what environmental variable(s), in the absence of bedrock, is/are responsible for influencing the spectral properties of the desert alluvial surface.

Reactor cavity seal ring

International Nuclear Information System (INIS)

Hankinson, M.F.

1986-01-01

A hydrostatic seal is described for sealing an annular gap between two flat substantially horizontal coplanar surfaces comprising, in combination: a generally flat annular plate of a width sufficient to span a gap between two surfaces: compressible annular sealing means disposed on the bottom surface of the flat annular plate for sealingly engaging the two flat surfaces in response to a downward force exerted on the plate; and fastening means, distributed along the center line of the plate, for releasably fastening the plate in a position to span the gap to be sealed and exert a downward force on the plate, each fastening means including a pair of elongated members of a size to fit into the gap to be sealed, means for mounting the members on the bottom surface of the plate so that at least a portion of each member is radially moveable in a direction toward a respective one of the vertical side surfaces defining the gap to be sealed to engage same and so that the plate is moveable relative to the members in a downward direction in response to hydrostatic pressure applied to the upper surface of the plate when the members are engaging the vertical side surfaces of an annular gap, and an actuating means, mounted on the plate for movement therewith in response to hydrostatic pressure, for radially moving the members, the actuating means extending through a bore in the plate to the upper surface of the plate

Bonding techniques for flexural strengthening of R.C. beams using CFRP laminates

Directory of Open Access Journals (Sweden)

Alaa Morsy

2013-09-01

Full Text Available This paper presents an experimental study of an alternative method of attaching FRP laminates to reinforced concrete beams by the way of fasting steel rivets through the FRP laminate and concrete substrate. Five full scale R.C. beams were casted and strengthened in flexural using FRP laminate bonded with conventional epoxy and compared with other beams strengthened with FRP laminate and bonded with fastener “steel rivets” of 50 mm length and 10 mm diameter. Based on experimental evidence the beam strengthened with conventional bonding methods failed due to de-bonding with about 13% increase over the un-strengthened beam. On the other hand, the beams strengthened with FRP laminate and bonded by four steel fastener rivets only failed by de-bonding also but at higher flexural capacity with increase 19% over the un-strengthened beam.

Effect of a new condensation product on electrodeposition of zinc ...

Indian Academy of Sciences (India)

TECS

steel in aerospace, electrical, and fastener industries owing to its excellent corrosion ... The most commonly used sacrificial coating is zinc and its alloys. Zinc by ... cause of their non-polluting nature (Arthoba Naik et al. 2002). Organic additives ...

16 CFR 1025.14 - Form and filing of documents.

Science.gov (United States)

2010-01-01

... in size. Print shall not be less than standard elite or 12 point type. Pages shall be fastened in the upper left corner or along the left margin. (3) Documents that fail to comply with this section may be...

21 CFR 888.3060 - Spinal intervertebral body fixation orthosis.

Science.gov (United States)

2010-04-01

... the plates. A braided cable is threaded through each eye-type screw. The cable is tightened with a tension device and it is fastened or crimped at each eye-type screw. The device is used to apply force to...

Characterisation of metal–thermoplastic composite hybrid joints by means of a mandrel peel test

NARCIS (Netherlands)

Su, Yibo; de Rooij, Matthias B.; Grouve, Wouter Johannes Bernardus; Warnet, Laurent

2016-01-01

Fastener free metal–carbon fibre reinforced thermoplastic composite hybrid joints show potential for application in aerospace structures. The strength of the metal–thermoplastic composite interface is crucial for the performance of the entire hybrid joint. Optimisation of the interface requires an

Electrodeposition and corrosion properties of zn-co and zn-co-fe alloy coatings

NARCIS (Netherlands)

Mol, J.M.C.; Lodhi, Z.F.; Hovestad, A.; Hoen-Velterop, L. 't; Terryn, H.; Wit, J.H.W. de

2010-01-01

Cadmium (Cd) has been extensively used as an excellent corrosion protective coating for steel components in aerospace, automotive, electrical and fasteners industries. However, Cd is banned due to its toxic nature and strict environmental regulations. In this study, the electrodeposition mechanism

Electrodeposition and corrosion properties of Zn-Co and Zn-Co-Fe alloy coatings

NARCIS (Netherlands)

Mol, J.M.C.; Lodhi, Z.F.; Hovestad, A.; Hoen-Velterop, L. 't; Terryn, H.; Wit, J.H.W. de

2011-01-01

Cadmium (Cd) has been extensively used as an excellent corrosion protective coating for steel components in aerospace, automotive, electrical and fasteners industries. However, Cd is banned due to its toxic nature and strict environmental regulations. In this study, the electrodeposition mechanism

Sensitivity analysis of railpad parameters on vertical railway track dynamics

NARCIS (Netherlands)

Oregui Echeverria-Berreyarza, M.; Nunez Vicencio, Alfredo; Dollevoet, R.P.B.J.; Li, Z.

2016-01-01

This paper presents a sensitivity analysis of railpad parameters on vertical railway track dynamics, incorporating the nonlinear behavior of the fastening (i.e., downward forces compress the railpad whereas upward forces are resisted by the clamps). For this purpose, solid railpads, rail-railpad

75 FR 15679 - Foreign-Trade Zone 272-Lehigh Valley, Pennsylvania Application for Subzone Grundfos Pumps...

Science.gov (United States)

2010-03-30

..., plastic closures and o- rings, rubber o-rings and gaskets, labels, pipe fittings, fasteners, motor... to realize logistical benefits through the use of weekly customs entry procedures. Customs duties also could possibly be deferred or reduced on foreign status production equipment. The request...

Morphology and corrosion resistance of Zn-Co and Zn-Co-Fe alloy coatings

NARCIS (Netherlands)

Lodhi, Z.F.; Mol, L.M.C.; Hovestad, A.; Terryn, H.; Wit, J.H.W. de

2008-01-01

Cadmium (Cd) has been extensively used as an excellent corrosion protective coating for steel applications in aerospace, automotive, electrical and fasteners industries. However, Cd is banned due to its toxic nature and strict environmental regulations. In this study, the coating morphology and

Angle-Beam Shear Wave Scattering from Buried Crack-like Defects in Bonded Specimens (Postprint)

Science.gov (United States)

2017-02-01

defects: such as understanding the scattering behavior of fatigue cracks emanating from fastener holes in aluminum structural components [2]. Angle...Ultrasonic NDE techniques using angle-beam wedges coupled to PZT transducers have also been utilized in measuring the depth of surface-breaking cracks

PV module mounting method and mounting assembly

Science.gov (United States)

Lenox, Carl J.S.; Johnson, Kurt M.

2013-04-23

A method for mounting PV modules to a deck includes selecting PV module layout pattern so that adjacent PV module edges are spaced apart. PV mounting and support assemblies are secured to the deck according to the layout pattern using fasteners extending into the deck. The PV modules are placed on the PV mounting and support assemblies. Retaining elements are located over and secured against the upper peripheral edge surfaces of the PV modules so to secure them to the deck with the peripheral edges of the PV modules spaced apart from the deck. In some examples a PV module mounting assembly, for use on a shingled deck, comprises flashing, a base mountable on the flashing, a deck-penetrating fastener engageable with the base and securable to the deck so to secure the flashing and the base to the shingled deck, and PV module mounting hardware securable to the base.

Magnetic Tomography - Assessing Tie Bar and Dowel Bar Placement Accuracy : Technical Summary

Science.gov (United States)

2017-12-01

Timely detection of misplaced steel would provide feedback needed to correct the construction process. To address this need, KDOT developed a field instrument capable of non-destructively assessing the placement (depth and orientation) accuracy of re...

Getting It Right in Ethical Experience: John McDowell and Virtue Ethics

DEFF Research Database (Denmark)

Christensen, Anne-Marie Søndergaard

2009-01-01

Most forms of virtue ethics are characterized by two attractive features. The first is that proponents of virtue ethics acknowledge the need to describe how moral agents acquire or develop the traits and abilities necessary to become morally able agents. The second attractive feature of most forms...... of virtue ethics is that they are forms of moral realism. The two features come together in the attempt to describe virtue as a personal ability to distinguish morally good reasons for action. It follows from the general picture of virtue ethics presented here that we cannot evaluate ethical judgment...

Slimhole drilling and directional drilling for on-site inspections under a Comprehensive Test Ban - An initial assessment

International Nuclear Information System (INIS)

Heuze, F.E.

1995-07-01

It appears that a short list of four suppliers should be further evaluated to formulate OSI-applicable packages. They are Baker-Hughes ESTTEQ, SLIMDRIL International, Halliburton Energy/ENSCO Technology, and Schlumberger-Dowell/Anadrill. It is noteworthy that all of them are headquartered in Houston, TX, making it a logical place to present the OSI requirements to a community of expert drillers. We have requested from these companies that they let us know of operations with coiled tubing to be conducted in California, so as to use such opportunities to view the systems in action. On such job was just completed by Schlumberger-Dowell near Bakersfield, and they have another one coming up in late July in Long Beach. An example of the 'footprint' of such a C-T drilling operation is shown. The Verification community also can take advantage of drilling conferences to keep up with the state-of-the-art. The next such meeting, co-sponsored by the International Association of Drilling Contractors (IADC) and the Society of Petroleum Engineers (SPE), is scheduled for March 12-15, 1996, in New Orleans. The next step in this study should be to determine an optimal combination of the new drilling methods with the health and safety procedures and the diagnostics which are required when drilling in a radioactive environment. This will involve bringing together the expertise of the NTS/National Laboratories with those of the exploration/production drillers. The final outcome will be the formulation of drilling systems which have significant cost and weight advantages over those of the equipment previously used at NTS

For your eyes only: Effect of confederate's eye level on reach-to-grasp action

Directory of Open Access Journals (Sweden)

Francois eQuesque

2014-12-01

Full Text Available Previous studies have shown that the spatio-temporal parameters of reach-to-grasp movement are influenced by the social context in which the motor action is performed. In particular, when interacting with a confederate, movements are slower, with longer initiation times and more ample trajectories, which has been interpreted as implicit communicative information emerging through voluntary movement to catch the partner’s attention and optimize cooperation (Quesque et al., 2013. Because gaze is a crucial component of social interactions, the present study evaluated the role of a confederate's eye level on the social modulation of trajectory curvature. An actor and a partner facing each other took part in a cooperative task consisting, for one of them, of grasping and moving a wooden dowel under time constraints. Before this Main action, the actor performed a Preparatory action, which consisted of placing the wooden dowel on a central marking. The partner's eye level was unnoticeably varied using an adjustable seat that matched or was higher than the actor’s seat. Our data confirmed the previous effects of social intention on motor responses. Furthermore, we observed an effect of the partner's eye level on the Preparatory action, leading the actors to exaggerate unconsciously the trajectory curvature in relation to their partner's eye level. No interaction was found between the actor's social intention and their partner's eye level. These results suggest that other bodies are implicitly taken into account when a reach-to-grasp movement is produced in a social context.

3-D Analysis of Flanged Joints Through Various Preload Methods Using ANSYS

Science.gov (United States)

Murugan, Jeyaraj Paul; Kurian, Thomas; Jayaprakash, Janardhan; Sreedharapanickar, Somanath

2015-10-01

Flanged joints are being employed in aerospace solid rocket motor hardware for the integration of various systems or subsystems. Hence, the design of flanged joints is very important in ensuring the integrity of motor while functioning. As these joints are subjected to higher loads due to internal pressure acting inside the motor chamber, an appropriate preload is required to be applied in this joint before subjecting it to the external load. Preload, also known as clamp load, is applied on the fastener and helps to hold the mating flanges together. Generally preload is simulated as a thermal load and the exact preload is obtained through number of iterations. Infact, more iterations are required when considering the material nonlinearity of the bolt. This way of simulation will take more computational time for generating the required preload. Now a days most commercial software packages use pretension elements for simulating the preload. This element does not require iterations for inducing the preload and it can be solved with single iteration. This approach takes less computational time and thus one can study the characteristics of the joint easily by varying the preload. When the structure contains more number of joints with different sizes of fasteners, pretension elements can be used compared to thermal load approach for simulating each size of fastener. This paper covers the details of analyses carried out simulating the preload through various options viz., preload through thermal, initial state command and pretension element etc. using ANSYS finite element package.

INFLUENCING OF FRICTION IN HINGES FORCE SIZE OF BARS

Directory of Open Access Journals (Sweden)

BOHOMAZ V. N.

2016-04-01

Full Text Available Formulation of the problem. The size of critical force of bar on the traditional method of calculation is determined in supposition of ideal hinge in the place of fixing of bar. There are both a hinge resistance at the turn of bar ends and their moving in the real hinges. Thus, there is the necessity of influencing character determination of these hinge imperfections on the size of critical force. In the existent scientific labours is devoted the alike problems, influencing of friction in the hinges of bar fastening on the size of critical force was not taken into account. At determination of bars stability with no ideality of hinges friction in them it is possible to take into account by the eccentric appendix of loading or appendix of moment. However at such approach it is difficult enough to define the size of attached force or moment. Purpose. To set influencing of friction in the hinge of bar fastening on of his critical force size in sense of Euler, and also build dependences for determination of bar critical force taking into account mechanical descriptions of hinges materials. Conclusion. For the task of determination the size of bar critical force with the joint fastening on ends are got the dependences which take into account mechanical descriptions of material hinge. The received dependences allow to define more exact meaning of critical force for bars. The examples of calculation of whole bar and bar with undercuting in the middle are resulted that values of critical force, certain on a traditional method are overpriced.

Dermal exposure to monoterpenes during wood work.

Science.gov (United States)

Eriksson, Kare; Wiklund, Leif

2004-06-01

The dermal exposure to the suspected allergenic monoterpenes [small alpha]-pinene, [small beta]-pinene and [capital Delta](3)-carene was assessed with a patch sampling technique. The patch used was made of activated charcoal sandwiched between two layers of cotton cloth. Patches were fastened at 12 different spots on a sampling overall and at the front of a cap to estimate the potential exposure of the body. Fastening two patches on a cotton glove, one patch representing the dorsal side and one patch representing the palm of the hand respectively, assessed the exposure on the hands. Sampling was carried out during collecting of pine and spruce boards in sawmills and during sawing of pine wood pieces in joinery shops respectively. The potential dermal exposure of the total body was 29.0-1 890 mg h(-1) with a geometric mean (GM) of 238 mg h(-1) during sawing. During collecting the GM was estimated to 100 mg h(-1) with a range of 12.2-959 mg h(-1). The hands had a mean exposure of 9.24 mg h(-1) during sawing and 3.25 mg h(-1) during collecting respectively. The good correlation between the mass of contamination on the individual body parts and the potential body exposure indicates that sampling can be performed on one body part to give a good estimation of the potential body exposure. Monoterpenes were detected at patches fastened underneath the protective clothing indicating a contamination of the skin of the worker. The patch used may overestimate the dermal exposure.

49 CFR 213.343 - Continuous welded rail (CWR).

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and...) Designation of a desired rail installation temperature range for the geographic area in which the CWR is... installation temperature range when adjusting CWR. (b) Rail anchoring or fastening requirements that will...

Tremor

Science.gov (United States)

... clothes with Velcro fasteners or using button hooks Cooking or eating with utensils that have a larger handle Using a sippy cup to drink Wearing slip-on shoes and using shoehorns When to Contact a Medical Professional Call your provider if your tremor: Is worse ...

Negative Rotation Cinch Strap.

Science.gov (United States)

This project discloses an improved unitary parachute torso harness, having a single fastening means, wherein an auxillary tightening strap is...attached to the groin straps of said harness. Said auxillary straps are used to prevent torso rotation or harness slippage and to prevent harness elongation

76 FR 36079 - Foreign-Trade Subzone 38A; Application for Expansion of Manufacturing Authority (Production...

Science.gov (United States)

2011-06-21

..., plastic and rubber parts, mirrors, glass, wiring harnesses, fasteners, springs, electronic components... benefits through the use of weekly customs entry procedures. Customs duties also could possibly be deferred or reduced on foreign status production equipment. BMWMC would also be exempt from duty payments on...

Switchable adhesion by chemical functionality and topography

NARCIS (Netherlands)

Kamperman, M.M.G.; Synytska, A.

2012-01-01

Progress in adhesion technology over the last few decades has led to widespread replacement of mechanical fasteners with adhesive bonds. Despite the advances, it remains challenging to produce materials that are sticky on demand. In this feature article we highlight recent efforts to develop

40 CFR 420.126 - Pretreatment standards for new sources (PSNS).

Science.gov (United States)

2010-07-01

...) Galvanizing, terne coatings and other coatings—(1) Strip, sheet, and miscellaneous products. Subpart L... chromium shall be applicable only to galvanizing operations which discharge wastewaters from the chromate rinse step. (2) [Reserved] (b) Galvanizing and other coatings—(1) Wire products and fasteners. Subpart L...

76 FR 34890 - Track Safety Standards; Concrete Crossties

Science.gov (United States)

2011-06-15

...-0007, Notice No. 3] RIN 2130-AC01 Track Safety Standards; Concrete Crossties AGENCY: Federal Railroad... effective concrete crossties, for rail fastening systems connected to concrete crossties, and for automated inspections of track constructed with concrete crossties. The Track Safety Standards were amended via final...

49 CFR 236.702 - Arm, semaphore.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Arm, semaphore. 236.702 Section 236.702 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., semaphore. The part of a semaphore signal displaying an aspect. It consists of a blade fastened to a...

Advances in moment transfering dvw reinforced timber connections : analysis and experimental verification, Part 1

NARCIS (Netherlands)

Leijten, A.J.M.; Brandon, D.

2013-01-01

Considerable advances in the moment transferring capacity of timber connections are achieved by using densified veneer wood reinforcement and expanded tube fasteners. This study focuses on the rotational stiffness of two dvw reinforced connections joined in series by a steel plate in a splice and

78 FR 66330 - Certain Steel Threaded Rod From the People's Republic of China; Final Results of Third...

Science.gov (United States)

2013-11-05

...., Ltd Panther T&H Industry Co. Ltd PSGT Trading Jingjiang Ltd Qingdao Free Trade Zone Health Intl... Co., Ltd.; (4) Shanghai Furen International Trading; and (5) Shanghai Printing and Packaging...., Ltd Ningbo Pal International Trading Co. Ningbo Qunli Fastener Manufacture Co., Ltd Ningbo Shuanglin...

78 FR 21101 - Certain Steel Threaded Rod From the People's Republic of China: Preliminary Results of...

Science.gov (United States)

2013-04-09

.... Ltd. PSGT Trading Jingjiang Ltd. Qingdao Free Trade Zone Health Intl. Shanghai East Best Foreign Trade...) Shanghai Furen International Trading; and (5) Shanghai Printing and Packaging Machinery Corp. No other... International Trading Co. Ningbo Qunli Fastener Manufacture Co., Ltd. Ningbo Shuanglin Auto Parts Co., Ltd...

Strength Behaviour of Fatigue Cracked Lugs (Festigkeitsverhalten von Rissbehafteten Augenstaeben),

Science.gov (United States)

1981-01-01

either surface cracks or corner cracks at holes. NASA TN 1)-8244 64 A.F. Grandt Stress intensity factors for some through fracked fastener holes...with Hydropuise L~ngszylinder longitudinal cylinder Druckblversorgung =pressure oil Supply Hydraulikaggregat = hydraulic control unit Fig 7.5 Plan of

NIR detects, destroys insect pests

International Nuclear Information System (INIS)

McGraw, L.C.

1998-01-01

What’s good for Georgia peanuts may also be good for Kansas wheat. An electric eye that scans all food-grade peanuts for visual defects could one day do the same for wheat kernels. For peanuts, it’s a proven method for monitoring quality. In wheat, scanning with near-infrared (NIR) energy can reveal hidden insect infestations that lower wheat quality. ARS entomologists James E. Throne and James E. Baker and ARS agricultural engineer Floyd E. Dowell are the first to combine NIR with an automated grain-handling system to rapidly detect insects hidden in single wheat kernels

78 FR 2287 - Daimler Buses North America, Inc., a Subsidiary of Daimler North America Corp, Including On-Site...

Science.gov (United States)

2013-01-10

... subsidiary of Daimler North America Corp., including on-site leased workers from Noramtec, First Choice... America, Inc., a Subsidiary of Daimler North America Corp, Including On-Site Leased Workers From Noramtec, First Choice Staffing, Staff Works, and Mr. Santo Lamarco From Wurth Revcar Fasteners, Inc., Oriskany...

76 FR 6927 - Radio Experimentation and Market Trials Under Part 5 of the Commission's Rules and Streamlining...

Science.gov (United States)

2011-02-08

... bands or fasteners. Any envelopes must be disposed of before entering the building. Commercial overnight... license; and (3) the medical program experimental radio license. Under our proposed rule revisions, the... in high-value bands that may host the newest generation of consumer devices and applications--in...

75 FR 29976 - Initiation of Antidumping and Countervailing Duty Administrative Reviews

Science.gov (United States)

2010-05-28

...., Ltd. Yancheng H&M Pressure Valve York International (Northern Asia) Ltd. Yuyao Dianbo Machinery Co... Co. Ltd. Pennengineering Automotive Fastener Pinghu City Zhapu Screw Cap Qingdao H.R. International...., Ltd. Bergstrom China Group Bowen Casting Co Ltd Broad-Ocean Motor (Hong Kong) Co., Ltd. C.H. Robinson...

77 FR 65808 - Airworthiness Directives; Airbus Airplanes

Science.gov (United States)

2012-10-31

... Airworthiness Directives; Airbus Airplanes AGENCY: Federal Aviation Administration (FAA), Department of... Airbus Model A320-214 and -232 airplanes. This AD was prompted by reports that medium-head fasteners were... installation of upper panels on Frame 35 in Airbus A320 final assembly line. Investigations revealed that...

77 FR 12179 - Airworthiness Directives; Mooney Aviation Company, Inc. (Mooney) Airplanes

Science.gov (United States)

2012-02-29

... inspecting the tail pitch trim assembly for correct positioning and proper attachment and inspecting the Huck... the FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the... attachment and inspecting the Huck Bolt fasteners for proper security on certain Mooney Aviation Company, Inc...

78 FR 76257 - Rural Call Completion

Science.gov (United States)

2013-12-17

... must be held together with rubber bands or fasteners. Any envelopes must be disposed of before entering... Completion/Call Termination Handbook outlining standards and practices of the industry relevant to ensuring... telecommunications networks. Transmission facilities may be based on a single technology or a combination of...

15 CFR 280.214 - Hearings.

Science.gov (United States)

2010-01-01

... STANDARDS AND TECHNOLOGY, DEPARTMENT OF COMMERCE ACCREDITATION AND ASSESSMENT PROGRAMS FASTENER QUALITY... conducted in a fair and impartial manner by the administrative law judge, who may limit attendance at any... may nevertheless proceed, and that party's failure to appear will not affect the validity of the...

Interstitial Hardening of Stainless Steel for Enhanced Corrosion Resistance for Naval Applications

Science.gov (United States)

2017-03-01

smoothness of the final polish. All of the specimens were treated with the same acetylene-based carburizing recipe : 16 hat 450 oc in 0.05 liters/minute...novel low temperature (< 500 Celsius) interstitial hardening process for stainless steels for impellers, fasteners and other marine items. Although

Elementary and advanced modelling of the splitting strength of timber connections

NARCIS (Netherlands)

Schoenmakers, J.C.M.D.

2008-01-01

The load-bearing capacity of a timber member loaded perpendicular-to-grain by a connection is governed by either the embedment strength, the bending yield strength of the steel fasteners, or the splitting strength of the timber. Only coarse models for predicting the splitting strength are

78 FR 21276 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-04-10

.... Nut fractures could lead to additional nut or bolt fractures within that support rib, and these... corroded nuts on an outboard flap support rib. This proposed AD would require, for certain airplanes... ribs, related investigative and corrective actions if necessary, and replacement of all fasteners in...

15 CFR 280.210 - Discovery.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Discovery. 280.210 Section 280.210... STANDARDS AND TECHNOLOGY, DEPARTMENT OF COMMERCE ACCREDITATION AND ASSESSMENT PROGRAMS FASTENER QUALITY Enforcement § 280.210 Discovery. (a) General. The parties are encouraged to engage in voluntary discovery...

75 FR 49870 - Effects on Broadband Communications Networks of Damage to or Failure of Network Equipment or...

Science.gov (United States)

2010-08-16

... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Chapter I [PS Docket No. 10-92; DA 10-1357] Effects on Broadband Communications Networks of Damage to or Failure of Network Equipment or Severe Overload AGENCY... with rubber bands or fasteners. Any envelopes must be disposed of before entering the building...

Extending labor epidural analgesia using lidocaine plus either dexmedetomidine or epinephrine for emergency cesarean section

Directory of Open Access Journals (Sweden)

Riham Hasanein

2016-07-01

Conclusion: Epidural dexmedetomidine is comparable to epinephrine as an adjuvant to epidural lidocaine in fastening the onset of surgical anesthesia and resulted in better intraoperative analgesia and in longer duration of sensory and motor block in the settings of converting labor epidural analgesia for emergency CS.

24 CFR 3280.807 - Fixtures and appliances.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically listed...

A nuclear reactor with buffered control rods

International Nuclear Information System (INIS)

Bevilacqua, F.

1974-01-01

The control rods for, e.g., water-cooled reactors are fastened as units on common crossbars in vertical downward direction. The fastening on the crossbar is achieved by means of cross-shaped parts, e.g., in the shape of a double 'H'. A cylinder connected with a drive rod in normal operation is joined to each of the crossbars. In an emergency shut-down, this connection is interrupted and the control rod unit drops into the core through the action of gravity. Its fall is slowed down by a cushion or shock absorbing unit. For this purpose a piston is provided mounted on the supporting plate below the cylinder and guided within it. In the cylinder, the coolant is contained as damping medium. An upper opening in the cylinder serves as a ventilation hole. The movement of the piston is limited by a stopping part within the cylinder and slowed down by a spiral spring. (DG) [de

A study of high-strength bolts after dephosphoring

Directory of Open Access Journals (Sweden)

Shao-Yi Hsia

2016-03-01

Full Text Available A wide variety of fasteners are produced, including those for the automobile industry, household electrical appliances industry, architectural engineering, and even the aviation industry. The effects of the high-tensile bolt dephosphoring process on the entire fastener manufacturing process and its organizational characteristics and mechanical properties are analyzed and discussed in this study. Our experimental results reveal that the bolt dephosphoring process must be completed before heat treatment, which can be confirmed with a dephosphoring reagent or metallographic observation. Once bolt heat treatment is completed, bolts without dephosphoring appear to be coated with δ ferrite (delta ferrite composed of a phosphate coating and a phosphatizing coating, which are not easily removed. Heat treatment with phosphorus results in grain boundary segregation, causing embrittlement and a reduction in lattice bonding forces and resulting in a high risk of fracturing when bolts are used in high-temperature environments or undergo multiaxial stresses.

A modular scanning tunneling microscope with an interchangeable elastic closed cell and external actuators

International Nuclear Information System (INIS)

Bjarnason, Elias H.; Arnalds, Unnar B.; Olafsson, Sveinn

2006-01-01

We introduce a novel modular cell based scanning tunneling microscope with external piezoelectric actuators. A tip and a sample are contained in a closed interchangeable cell, consisting of a stiff top plate and a bottom part, fastened together by an elastic material. The bottom part, containing a scanning tip, is fastened to a base unit while the top plate, containing a sample, is capable of scanning motion by external piezoelectric actuators mounted in the same base unit. The actuators are pre-loaded by the deformation of the elastic material of the cell, giving an increased stability. This design is expected to simplify the scanning tunneling microscope (STM) operation in difficult environments greatly by enclosing only the tip and sample in a small cell-module, which is pluggable to a scanning mechanism and other supportive functionalities. A frequency characterization and an image scan showing atomic resolution of highly oriented graphite in air, at room temperature, is presented

Environmental Degradation of Fiber-Reinforced Polymer Fasteners in Wood

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2013-01-01

This paper examines the durability of fiber-reinforced polymer (FRP) nails in treated wood. The FRP nails were exposed to four conditions: (1) accelerated weathering, consisting of exposure to ultraviolet light and condensation; (2) 100% relative humidity (RH); (3) being driven into untreated wood and exposed to 100% RH; and (4) being driven into wood treated with...

Standardized Curriculum for Diesel Engine Mechanics.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: diesel engine mechanics I and II. The eight units in diesel engine mechanics I are as follows: orientation; shop safety; basic shop tools; fasteners; measurement; engine operating principles; engine components; and basic auxiliary…

Practical stress analysis in engineering design

CERN Document Server

Huston, Ronald

2008-01-01

Presents the application of engineering design and analysis based on the approach of understanding the physical characteristics of a given problem and then modeling the important aspects of the physical system. This book covers such topics as contact stress analysis, singularity functions, gear stresses, fasteners, shafts, and shaft stresses.

76 FR 44575 - Paper Clips From the People's Republic of China: Continuation of the Antidumping Duty Order

Science.gov (United States)

2011-07-26

..., butterfly clips, binder clips, or other paper fasteners that are not made wholly of wire of base metal and... DEPARTMENT OF COMMERCE International Trade Administration [A-570-826] Paper Clips From the People... the antidumping duty order on paper clips from the People's Republic of China (``PRC'') would likely...

15 CFR 280.201 - Violations.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Violations. 280.201 Section 280.201 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade NATIONAL INSTITUTE OF... otherwise, fasteners that are required by the applicable consensus standard or standards to bear an insignia...

77 FR 38324 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Science.gov (United States)

2012-06-27

... and inspecting for corrosion. (iii) Inspecting the contact points to ensure a secure connection to the...) Checking the battery compartment cover to ensure that it is securely fastened. (c) The results of such... integrity of the case. (ii) Removing the battery and inspecting for corrosion. (iii) Inspecting the contact...

TV white space networks deployment: a case study of Mankweng Township in South Africa

CSIR Research Space (South Africa)

Ramoroka, MT

2015-12-01

Full Text Available to communication systems can fasten the reduction of the development gap. In this work we analyze the benefits that can be obtained by application of TV White Space network, i.e. the network that operates in vacated TV band in a cognitive manner. The whole analysis...

76 FR 66685 - Foreign-Trade Zone 37-Orange County, NY, Application for Subzone, ITT Water Technology, Inc...

Science.gov (United States)

2011-10-27

..., plastic o-rings, rubber o-rings, shafts, flanges, motor and shaft couplings, and fasteners (duty rates... logistical benefits through the use of weekly customs entry procedures. Customs duties also could possibly be deferred or reduced on foreign status production equipment. The request indicates that the savings from FTZ...

Flat roofs, a grey area; Grauzone Flachdach

Energy Technology Data Exchange (ETDEWEB)

Riedel, Anja

2012-11-01

The boom of low-ballast assembly systems for flat roofs is going on. Solar assembly racks are set up directly on the sealing foil without fastening bolts. But what happens in case of water ingress? And what should be done to prevent damage to the roof cover? (orig.)

Small Engine Repair. Two-Stroke and Four-Stroke Cycle.

Science.gov (United States)

Hires, Bill; And Others

This curriculum guide is intended to assist persons teaching a course in repairing two- and four-stroke cycle small engines. Addressed in the individual units of instruction are the following topics: safety, tools, fasteners, and measurement techniques; basic small engine theory (engine identification and inspection, basic engine principles and…

75 FR 38001 - Airworthiness Directives; The Boeing Company Model 747 Airplanes

Science.gov (United States)

2010-07-01

...). Support Frame upper Corner 8 None 680 162 110,160 Fastener Inspection (new required action). Post.... This AD will not have a substantial direct effect on the States, on the relationship between the... impact, positive or negative, on a substantial number of small entities under the criteria of the...

Fentanyl versus magnesium sulphate as adjuvant to peribulbar anesthesia in cataract surgery

Directory of Open Access Journals (Sweden)

Mohamed M. Abu Elyazed

2017-04-01

Conclusions: Addition of fentanyl (2 μg/ml or magnesium sulphate (50 mg to peribulbar block in patients undergoing cataract surgery equally prolongs the duration of postoperative analgesia. In addition to this effect, fentanyl fastens the onset lid and globe akinesia and provides better akinesia score.

33 CFR 207.750 - Puget Sound Area, Wash.

Science.gov (United States)

2010-07-01

... fastened with tight-fitting covers. To preclude a concentration of potentially explosive vapors, no paint... permitted aboard vessels with cargoes of fuel or explosives. (ix) All vessels carrying hazardous cargoes... walls, or over the piers or grounds forming a part of the canal or its appurtenances. All persons in...

Astronomy on a Landfill

Science.gov (United States)

Venner, Laura

2008-09-01

Engaging "K-to-Gray” audiences (children, families, and older adults) in astronomical activities is one of the main goals of the NJMC Center for Environmental and Scientific Education and the William D. McDowell Observatory located in Lyndhurst, NJ. Perched atop a closed and reclaimed municipal solid waste landfill, our new LEED - certified building (certification pending) and William D. McDowell observatory will assist in bringing the goals of IYA 2009 to the approximately 25,000 students and 15,000 adults that visit our site from the NY/NJ region each year. Diversifying our traditional environmental science offerings, we have incorporated astronomy into our repertoire with "The Sun Through Time” module, which includes storytelling, cultural astronomy, telescope anatomy, and other activities that are based on the electromagnetic spectrum and our current knowledge of the sun. These lessons have also been modified to bring astronomy to underserved communities, specifically those individuals that have dexterity or cognitive ability differences. The program is conducted in a classroom setting and is designed to meet New Jersey Core Curriculum Content Standards. With the installation of our new 20” telescope, students and amateur astronomers will be given the opportunity to perform rudimentary research. In addition, a program is in development that will allow individuals to measure local sky brightness and understand the effects of light pollution on astronomical viewing. Teaching astronomy in an urban setting presents many challenges. All individuals, regardless of ability level or location, should be given the opportunity to be exposed to the wonders of the universe and the MEC/CESE has been successful in providing those opportunities.

New Deal Leftists, Henry Wallace and "Gideon's Army," and the Progressive Party in Montana, 1937-1952

Science.gov (United States)

Lovin, Hugh T.

2012-01-01

Many forces occupied America's sociopolitical terrain to the left of New Dealers who dominated U.S. President Franklin Roosevelt's administration of the 1930s. Some fastened themselves temporarily to the New Dealers' coattails. Ideologically motivated, others touted their special panaceas for ending the Great Depression that had begun in 1929, and…

Impact Driver With Integral Sliding Hammer

Science.gov (United States)

Wallace, Bilby J.

1987-01-01

Tool combines impact driver with sliding dead-blow hammer. Used for any purpose for which ordinary impact driver used; tightening fasteners or driving starter holes for drill. Tool protects user from accidental injury and surrounding equipment from damage that might occur from ordinary arm-wielded hammer. Especially useful in underwater work.

77 FR 27421 - Certain Steel Nails From the United Arab Emirates: Amended Final Determination of Sales at Less...

Science.gov (United States)

2012-05-10

... certain steel nails having a shaft length up to 12 inches. Certain steel nails include, but are not..., and have a variety of finishes, heads, shanks, point types, shaft lengths and shaft diameters... film tape backed with a heat seal adhesive; and Fasteners having a case hardness greater than or equal...

Portable and Lightweight Ramp Structure

Science.gov (United States)

2001-04-09

long side of which is in abutting relationship with the 12 short side of the end of the ramp. Fastener receivers are equi- 13 spaced in duplicate...The modular sections are conveniently prefabricated 18 1 and provided in kit form to the number of sections corresponding 2 to the desired ramp

Thermal Modeling of Millimeter Wave Energy and Heat Transfer in Skin

Science.gov (United States)

2008-11-25

micropore tape on the tail. A probe fastened to the Styrofoam stand measured ambient temperature. The temperatures from the three probes were recorded...weights at "n’s" indicated on figure. 18 Grant number FA9550-06-1-0129 question how the insulating qualities of adipose tissue should be

Motorcycle Mechanic. Teacher Edition.

Science.gov (United States)

Baugus, Mickey; Fulkerson, Dan, Ed.

These teacher's materials are for a 19-unit competency-based course on entry-level motorcycle mechanics at the secondary and postsecondary levels. The 19 units are: (1) introduction to motorcycle repair; (2) general safety; (3) tools and equipment; (4) metric measurements; (5) fasteners; (6) service department operations; (7) motorcycle engines;…

76 FR 54218 - Third Party Testing for Certain Children's Products; Toys: Requirements for Accreditation of...

Science.gov (United States)

2011-08-31

... webpage: http://www.cpsc.gov/toysafety . SUPPLEMENTARY INFORMATION: I. Introduction Section 14(a)(3)(B)(vi.... --Section 4.12, Packaging Film. --Section 4.13, Folding Mechanisms and Hinges. --Section 4.14, Cords, Straps....10, Wires or Rods. --Section 4.11, Nails and Fasteners. --Section 4.12, Packaging Film. --Section 4...

76 FR 46598 - Third Party Testing for Certain Children's Products; Toys: Requirements for Accreditation of...

Science.gov (United States)

2011-08-03

.../toysafety . SUPPLEMENTARY INFORMATION: I. Introduction Section 14(a)(3)(B)(vi) of the CPSA, as added by..., Packaging Film --Section 4.13, Folding Mechanisms and Hinges --Section 4.14, Cords, Straps, and Elastics....10, Wires or Rods --Section 4.11, Nails and Fasteners --Section 4.12, Packaging Film --Section 4.13...

75 FR 15629 - Airworthiness Directives; Cessna Aircraft Company Model 525A Airplanes

Science.gov (United States)

2010-03-30

... elevator damage and result in loss of control. DATES: We must receive comments on this proposed AD by May... thrust attenuator paddles are attached to the aft fuselage. The attachment fasteners fatigue and break... damage the elevator. We considered AD 2009-24-13 an interim action while Cessna developed a design...

15 CFR 280.313 - Recordal of additional insignia.

Science.gov (United States)

2010-01-01

... for recordal of its trademark for fasteners if the trademark is the subject of a duly filed application or is registered in the United States Patent and Trademark Office on the Principal Register. Upon recordal, either the alphanumeric designation or the trademark, or both, may be used as recorded insignias...

MRI of the Chest

Medline Plus

Full Text Available ... fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with the specific exam and with the imaging facility. Unless you are told otherwise, you may follow your regular daily routine and take food and medications as usual. Some MRI examinations may ...

Magnetic Resonance Imaging (MRI) -- Head

Medline Plus

Full Text Available ... fitting and has no metal fasteners. Guidelines about eating and drinking before an MRI exam vary with the specific exam and with the imaging facility. Unless you are told otherwise, you may follow your regular daily routine and take food and medications as usual. Some MRI examinations may ...

14 CFR 25.777 - Cockpit controls.

Science.gov (United States)

2010-01-01

.... Controls of a variable nature using a rotary motion must move clockwise from the off position, through an... harness (if provided) fastened. (d) Identical powerplant controls for each engine must be located to prevent confusion as to the engines they control. (e) Wing flap controls and other auxiliary lift device...

Conceptual Content and Unattended Visual Features

Directory of Open Access Journals (Sweden)

Francisco Pereira

2009-08-01

Full Text Available McDowell (1994 proposed a philosophical theory about perceptual content −call it “conceptualism”− that states that in every case the content of a visual experience necessarily involves concepts that fully specify every single feature consciously and simultaneously available during the experience. In this paper I will question conceptualism, arguing that some visual experiences carry information about so many objects, properties and relations at the same time that it is unlikely for subjects to possess and implement concepts for every feature represented simultaneously by the experience at that time. If this is the case, then McDowell’s conceptualism is insufficiently grounded.

Catenary Action in Rebars Crossing a Casting Joint Loaded in Shear

DEFF Research Database (Denmark)

Sørensen, Jesper Harrild; Hoang, Linh Cao; Olesen, John Forbes

2016-01-01

Reinforcement crossing a casting joint loaded in shear exhibits catenary action as the shear displacement increases. The load carrying capacity of such a joint is in practice often calculated by use of empirical methods to account for shear friction effects or by a first order plastic analysis...... if dowel action is included. The strength increase/reserve due to catenary action in the rebars is often neglected; however in some cases it may be necessary to utilize the effect in order to ensure overall structural robustness. This paper presents results of a study, where the increased shear capacity...... and theory is found when reasonable material properties are assumed....

Naturalism, Normativity, and the Study of Religion

Directory of Open Access Journals (Sweden)

Anil Mundra

2017-10-01

Full Text Available This article repudiates the common view that the study of religion, in order to qualify as academic, must be descriptively neutral and naturalistic rather than normative or prescriptive. Following philosophers like John McDowell, John Cottingham, and Tyler Roberts, I claim that such a methodological stance amounts to viewing humans as determined rather than free agents. On the basis of W.V.O. Quine and Donald Davidson’s analysis of translation, I argue that normativity is ineliminable from humanistic scholarship, which is itself inextricable from religious studies. Robert Pippin and Thomas A. Lewis’s readings of Hegel then provide resources to reconcile human freedom and constraint in religion.

Identification of the First Chinese Cases of H1N1 Flu

Centers for Disease Control (CDC) Podcasts

2009-08-04

In this podcast, Dr. Scott Dowell discusses the first cases of the new H1N1 influenza virus in China in May 2009, which occurred in three students who had been studying in North America during the early days of the pandemic and returned home to visit their friends and family. Chinese health officials acted swiftly to investigate and determine whether the students had spread their illness to others. The article, which appears in the September 2009 issue of Emerging Infectious Diseases, details what they found.  Created: 8/4/2009 by Emerging Infectious Diseases.   Date Released: 8/4/2009.

Making dowel-laminated crossties with the shaping-lathe headrigs- it should be profitable.

Science.gov (United States)

P. Koch

1976-01-01

Railroads of the nation must soon install increasing numbers of crossties if rail-beds are to be maintained at an acceptable level. But the problem is that hardwood logs large enough to make one-piece 7- by 9-inch crossties will likely be in short supply. Fortunately, a process is available whereby plentiful small logs can be converted into the needed mainline ties....

Application Problems of Anchor Dowels in Reinforced Concrete Shear Wall and Frame Connections

OpenAIRE

Musa H. Arslan

2016-01-01

Strengthening of the existing seismically deficient reinforced concrete (RC) buildings is an important issue in earthquake prone regions. Addition of RC shear wall as infill or external walls into the structural system has been a commonly preferred strengthening technique since the Big Erzincan Earthquake occurred in Turkey, 1992. The newly added rigid infill walls act primarily as shear walls and relieve the non-ductile existing frames from being subjected to large shear demands providing th...

75 FR 1536 - Airworthiness Directives; The Boeing Company Model 737-600, -700, and -800 Series Airplanes

Science.gov (United States)

2010-01-12

... alteration, design change, or repair involving new penetrations of the fuel tanks (such as a repair with... structure is affected, while the structural repair does not disrupt the fuel tank system. CAL states that it... instructions require installing fasteners into the fuel tank. CAL notes that FAA approval of the MPD AWLs can...

75 FR 38056 - Airworthiness Directives; McDonnell Douglas Corporation Model MD-90-30 Airplanes

Science.gov (United States)

2010-07-01

...-0645; Directorate Identifier 2009-NM-200-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas..., September 9, 2008), for certain McDonnell Douglas Corporation Model MD-90-30 airplanes. That AD requires a... fasteners in the aft mount support fitting of the left and right engines on 29 McDonnell Douglas Corporation...

Healthy Environments for Children

Science.gov (United States)

... AND BE SURE EVERYONE WEARS A HELMET WHEN BIKING. IN THE CAR, CHILDREN SHOULD SIT IN THE BACK SEAT AND ALWAYS FASTEN THEIR SEAT BELTS! 14 AND CHILDREN SHOULD BE TAUGHT TO SWIM FROM THE TIME THEY’RE SMALL. IT’S GOOD FOR THEIR HEALTH AND THEIR SAFETY. PROTECTING CHILDREN FROM DANGERS IN ...

77 FR 24462 - Certain Steel Nails From the People's Republic of China: Amended Final Results of the Second...

Science.gov (United States)

2012-04-24

... merchandise covered by the order includes certain steel nails having a shaft length up to 12 inches. Certain..., shaft lengths and shaft diameters. Finishes include, but are not limited to, coating in vinyl, zinc... backed with a heat seal adhesive. Also excluded from the scope of the order are fasteners having a case...

75 FR 3660 - Airworthiness Directives; The Boeing Company Model 757 Airplanes

Science.gov (United States)

2010-01-22

... airplanes. This proposed AD would require repetitive inspections for corrosion and cracking in the front... side link support fitting at WS 292. We are proposing this AD to detect and correct such corrosion and... fastener locations common to the side link support fitting at WS 292. This area is not covered by the...

46 CFR 61.20-5 - Drydock examination.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Drydock examination. 61.20-5 Section 61.20-5 Shipping... INSPECTIONS Periodic Tests of Machinery and Equipment § 61.20-5 Drydock examination. (a) When any vessel is drydocked, examination shall be made of the propeller, stern bushing, sea connection, and fastenings if...

9 CFR 93.805 - Ports of entry, inspection, and treatment. 1

Science.gov (United States)

2010-01-01

... in paragraph (b)(3) of this section, and any plastic sheet used to wrap any shipping crate, shall be... shipping crate or vehicle containing the animal shall be removed, sealed in plastic bags, and incinerated... crate, plastic must be fastened around the shipping crate so that all animal waste, hay, straw, feed...

75 FR 35265 - Safety Standard for Infant Walkers: Final Rule

Science.gov (United States)

2010-06-21

... are walking (usually 6 to 15 months old). ASTM F 977-07 defines ``walker'' as ``a mobile unit that... attached to rigid trays. The trays are fastened to bases that have wheels or casters to make them mobile.../jumping. Occupant retention--intended to prevent entrapment by setting requirements for leg openings. The...

Pull-Through Capacity in Plywood and OSB

DEFF Research Database (Denmark)

Munch-Andersen, Jørgen; Sørensen, John Dalsgaard

The characteristic pull-through capacity of heads of nails and screws is needed to determine the rope effect for laterally loaded fasteners used to fix sheathing to timberframes. There is no values given in EN 1995 (Eurocode 5) but data for the pull through capacity of nail and screw heads has be...

29 CFR 1910.215 - Abrasive wheel machinery.

Science.gov (United States)

2010-07-01

... be securely fastened to the spindle and the bearing surface shall run true. When more than one wheel... 29 Labor 5 2010-07-01 2010-07-01 false Abrasive wheel machinery. 1910.215 Section 1910.215 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery. (a...

Inedible Nuts and Non-Lightning Bolts

Science.gov (United States)

Rynone, William

2010-01-01

In this article, the author provides detailed information on a wide variety of commonly used screws, bolts, and other fasteners. The information has been gathered in his engineering career and outside interests (maintenance on his car and airplane, and woodworking). The topic should be of interest to students and educators in many technical…

49 CFR 238.429 - Safety appliances.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances. 238.429 Section 238.429... Equipment § 238.429 Safety appliances. (a) Couplers. (1) The leading and the trailing ends of a semi... appliance mechanical strength and fasteners. (1) All handrails, handholds, and sill steps shall be made of 1...

GPR use and activities in the Czech Republic

Science.gov (United States)

Stryk, Josef; Matula, Radek

2014-05-01

In the field of civil engineering applications in the Czech Republic, Ground Penetrating Radar (GPR) is used particularly for the diagnostics of roads and bridges. There is no producer of GPR in the Czech Republic, sets of different producers are used, particularly Geophysical Survey Systems, Inc. (USA) and MALÅ GeoScience (Sweden). The measurement results are mostly processed by software Radan, Road Doctor Pro, ReflexW and RadEx. The only technical specification in the Czech Republic is TP 233 issued by the Ministry of Transport, which describes the diagnostics of roads by GPR. Apart from a basic description of the method and a measurement system, it mentions possible applications. The only application where accuracy is mentioned is the locating of dowels and tie bars in concrete road pavements, which states that if calibration is performed, the expected depth accuracy is up to 1.0 cm. The following R&D project is currently in progress: New diagnostics methods as a supporting decision tool for maintenance and repair of road pavements - their contribution and ways of their usage (2012-2014) The project aims to test possible non-destructive methods (particularly GPR and laser scanning), make recommendations when and how to use specific methods for individual applications and for changes in technical specifications. The following R&D projects have been recently completed: Position of dowels and tie bars in rigid pavements and importance of their correct placement to pavement performance and service life (2012-2013) The project included an analysis of individual NDT methods used for the location of dowels and tie bars and for testing of their accuracy - GPR, MIT-scan and GPR in combination with a metal detector. Multichannel ground penetrating radar as a tool for monitoring of road and bridge structures (2009-2011) The project included detection of hollow spaces under non-reinforced concrete pavements, detection of excessive amount of water in road construction

Radioactive fuel cask railcar humping study

International Nuclear Information System (INIS)

Wilson, L.T.

1978-01-01

The response of two radioactive shipping casks due to railroad humping shocks was calculated using a spring-mass model. The two railcars for these casks had different coupling mechanisms and different tiedown arrangements. Humping tests had been performed on one of the railcars (ATMX-600) and the resulting shock spectra was used to adjust the spring-mass model to get matching results. One car (designed for cask shipment) was equipped with Freightmaster E-15 end of car coupler and had about 1 / 8 in. free travel of the cask skid relative to the car. The other car (ATMX-600), equipped with Miner RF-333 draft gear, was designed for nuclear weapon shipment and adapted to nuclear waste shipment by fastening the casks to the floor. Both car frames were built by the same manufacturer and are very similar. The response of the casks was put in shock spectra format and a parametric study was performed with various cask weights. Additional studies were done on the effects of fastening the loose cask, and using the Freightmaster end of car coupler on the ATMX car. Half-sine response spectra were overlaid to include the natural frequency of the cask tiedown. The resulting shock amplitude was plotted against the cask weight for each car. The results show a constant acceleration level for all the weights on the car with hydraulic end-of-car coupler which results from constant force at that impact velocity. The cask acceleration can be reduced by fastening it to the car, rather than allowing it to move freely through some small space. This study also shows that the cask response can be optimized on railcars without hydraulic draft gear by adjusting the tiedown stiffness to keep the tiedown frequency different than car frequencies

A nuclear power reactor

International Nuclear Information System (INIS)

Borrman, B.E.; Broden, P.; Lundin, N.

1979-12-01

The invention consists of shock absorbing support beams fastened to the underside of the reactor tank lid of a BWR type reactor, whose purpose is to provide support to the steam separator and dryer unit against accelerations due to earthquakes, without causing undue thermal stresses in the unit due to differential expansion. (J.I.W.)

Seat belt reminders.

NARCIS (Netherlands)

2008-01-01

Seat belts are an effective way of reducing the number or road deaths and severe road injuries in crashes. Seat belt reminders warn car drivers and passengers if the seat belt is not fastened. This can be done by a visual signal or an acoustic signal or by a combination of the two. Seat belt

Modeling the Effect of Nail Corrosion on the Lateral Strength of Joints

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2012-01-01

This article describes a theoretical method of linking fastener corrosion in wood connections to potential reduction in lateral shear strength. It builds upon published quantitative data of corrosion rates of metals in contact with treated wood for several different wood preservatives. These corrosion rates are then combined with yield theory equations to calculate a...

Preliminary Investigation of Several Root Designs for Cermet Turbine Blades in Turbojet Engine III : Curved-root Design

Science.gov (United States)

Pinkel, Benjamin; Deutsch, George C; Morgan, William C

1955-01-01

Stresses om tje root fastenings of turbine blades were appreciably reduced by redesign of the root. The redesign consisted in curving the root to approximately conform to the camber of the airfoil and elimination of the blade platform. Full-scale jet-engine tests at rated speed using cermet blades of the design confirmed the improvement.

36 CFR 1004.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Safety belts. 1004.15 Section 1004.15 Parks, Forests, and Public Property PRESIDIO TRUST VEHICLES AND TRAFFIC SAFETY § 1004.15 Safety... administered by the Presidio Trust will have the safety belt or child restraint system properly fastened at all...

77 FR 73265 - Airworthiness Directives; Erickson Air-Crane Incorporated Helicopters

Science.gov (United States)

2012-12-10

... attention to the fastener attachment holes, as shown in Figure 1, Detail B, of the Accomplishment...-66340-043 or -044, for a crack. Pay particular attention to the circled areas shown in Figure 2 of the... Office, M-30, West Building Ground Floor, Room W12- 140, 1200 New Jersey Avenue SE., Washington, DC 20590...

49 CFR 213.110 - Gage restraint measurement systems.

Science.gov (United States)

2010-10-01

... requirements specified in §§ 213.109 and 213.127. (5) If the PTLF becomes non-functional or is missing, the... and fastener requirements specified in §§ 213.109 and 213.127 provided that— (1) The track owner... the minimum design requirements of a GRMS vehicle which specify that— (1) Gage restraint shall be...

A method to determine validity and reliability of activity sensors

NARCIS (Netherlands)

Boerema, Simone Theresa; Hermens, Hermanus J.

2013-01-01

METHOD Four sensors were securely fastened to a mechanical oscillator (Vibration Exciter, type 4809, Brüel & Kjær) and moved at various frequencies (6.67Hz; 13.45Hz; 19.88Hz) within the range of human physical activity. For each of the three sensor axes, the sensors were simultaneously moved for

Supportability in Aircraft Systems through Technology and Acquisition Strategy Applications.

Science.gov (United States)

1987-09-01

structures is their corrosion resistance. These integral structures are water impregnable. Also, the absence of rivet and fastener hole eliminates the...REPCRT SECURITY CLASS,F,CAT ON lb RESTR;CTIVE MARK.NGSU",CLAS S I7 F 15E Za. SECURITY CLASSiFICAT;ON AUTHORITY 3 DISTRiBUTiQN/ AVAILABILIT ’ OF REPORT

Withdrawal Strength and Bending Yield Strength of Stainless Steel Nails

Science.gov (United States)

Douglas R. Rammer; Samuel L. Zelinka

2015-01-01

It has been well established that stainless steel nails have superior corrosion performance compared to carbon steel or galvanized nails in treated wood; however, their mechanical fastening behavior is unknown. In this paper, the performance of stainless steel nails is examined with respect to two important properties used in wood connection design: withdrawal strength...

Corrosion of metals in wood : comparing the results of a rapid test method with long-term exposure tests across six wood treatments

Science.gov (United States)

Samuel L. Zelinka; Donald S. Stone

2011-01-01

This paper compares two methods of measuring the corrosion of steel and galvanized steel in wood: a long-term exposure test in solid wood and a rapid test method where fasteners are electrochemically polarized in extracts of wood treated with six different treatments. For traditional wood preservatives, the electrochemical extract method correlates with solid wood...

78 FR 33012 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-06-03

... prompted by an evaluation by the design approval holder (DAH) indicating that certain fuselage frame shear... cracks at the shear tie end fastener locations of the fuselage frames, and repairing cracks if necessary... in 14 CFR 11.43 and 11.45, by any of the following methods: Federal eRulemaking Portal: Go to http...

76 FR 72858 - Airworthiness Directives; The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500...

Science.gov (United States)

2011-11-28

... Model 737-100, -200, -300, -400, and -500 series airplanes, a one-time detailed inspection is added to... Information Initial Compliance Time (i) For all Model 737-100, -200, -200C, -300, -400, and -500 series... by paragraph (r) of this AD. If any fastener is missing, before further flight, repair using a method...

The C-terminal domain of the Arabidopsis AtMBD7 protein confers strong chromatin binding activity

International Nuclear Information System (INIS)

Zemach, Assaf; Paul, Laju K.; Stambolsky, Perry; Efroni, Idan; Rotter, Varda; Grafi, Gideon

2009-01-01

The Arabidopsis MBD7 (AtMBD7) - a naturally occurring poly MBD protein - was previously found to be functional in binding methylated-CpG dinucleotides in vitro and localized to highly methylated chromocenters in vivo. Furthermore, AtMBD7 has significantly lower mobility within the nucleus conferred by cooperative activity of its three MBD motifs. Here we show that besides the MBD motifs, AtMBD7 possesses a strong chromatin binding domain located at its C-terminus designated sticky-C (StkC). Mutational analysis showed that a glutamic acid residue near the C-terminus is essential though not sufficient for the StkC function. Further analysis demonstrated that this motif can render nuclear proteins highly immobile both in plant and animal cells, without affecting their native subnuclear localization. Thus, the C-terminal, StkC motif plays an important role in fastening AtMBD7 to its chromosomal, CpG-methylated sites. It may be possible to utilize this motif for fastening nuclear proteins to their chromosomal sites both in plant and animal cells for research and gene therapy applications.

An Analytical Model for Rotation Stiffness and Deformation of an Antiloosening Nut under Locking Force

Directory of Open Access Journals (Sweden)

X. J. Jiang

2014-01-01

Full Text Available Screw fasteners are undoubtedly one of the most important machine elements due to their outstanding characteristic to provide a high clamping force just with a simplified design. However, the loosen vibration is their inherent and inevitable fault. The friction locking approach is one of the basic locking fastener categories by enhancing the bearing load on the contact surface of thread by applying a locking force on an antiloosening nut. This locking force may cause more severe deformation in the nut. The contact stress distribution on the nut would be changed and that can cause the variation of the friction torque for the bolt joint. However, there exists no established design calculation procedure that accounts for the rotation deformation and its stiffness of the antiloosening nut under the locking force. The main objective of the work is to develop an analytical solution to the rotation deformation problem encountered in the antiloosening nut. The proposed model is supported by comparison with numerical finite element analysis of different sizes of joint elements and different applied forces.

Fatigue crack growth monitoring in multi-layered structures using guided ultrasonic waves

International Nuclear Information System (INIS)

Kostson, E; Fromme, P

2009-01-01

This contribution investigates the application of low frequency guided ultrasonic waves for monitoring fatigue crack growth at fastener holes in the 2nd layer of multi-layered plate structures, a common problem in aerospace industry. The model multi-layered structure investigated consists of two aluminum plate-strips adhesively bonded using a structural paste adhesive. Guided ultrasonic waves were excited using multiple piezoelectric discs bonded to the surface of the multi-layered structure. The wave propagation in the tensile specimen was measured using a laser interferometer and compared to numerical simulations. Thickness and width mode shapes of the excited flexural waves were identified from Semi-Analytical Finite Element (SAFE) calculations. Experiments and 3D Finite Element (FE) simulations show a change in the scattered field around fastener holes caused by a defect in the 2nd layer. The amplitude of the guided ultrasonic wave was monitored during fatigue experiments at a single point. The measured changes in the amplitude of the ultrasonic signal due to fatigue crack growth agree well with FE simulations.

Fabrication Improvement of Cold Forging Hexagonal Nuts by Computational Analysis and Experiment Verification

Directory of Open Access Journals (Sweden)

Shao-Yi Hsia

2015-01-01

Full Text Available Cold forging has played a critical role in fasteners and has been applied to the automobile industry, construction industry, aerospace industry, and living products so that cold forging presents the opportunities for manufacturing more products. By using computer simulation, this study attempts to analyze the process of creating machine parts, such as hexagonal nuts. The DEFORM-3D forming software is applied to analyze the process at various stages in the computer simulation, and the compression test is also used for the flow stress equation in order to compare the differences between the experimental results and the equation that is built into the computer simulation software. At the same time, the metallography and hardness of experiments are utilized to understand the cold forging characteristics of hexagonal nuts. The research results would benefit machinery businesses to realize the forging load and forming conditions at various stages before the fastener formation. In addition to planning proper die design and production, the quality of the produced hexagonal nuts would be more stable to promote industrial competitiveness.

Cell wall domain and moisture content influence southern pine electrical conductivity

Science.gov (United States)

Samuel L. Zelinka; Leandro Passarini; José L. Colon Quintana; Samuel V. Glass; Joseph E. Jakes; Alex C. Wiedenhoeft

2016-01-01

Recent work has highlighted the importance of movement of chemicals and ions through the wood cell wall. This movement depends strongly on moisture content and is necessary for structural damage mechanisms such as fastener corrosion and wood decay. Here, we present the first measurements of electrical resistance of southern pine at the subcellular level as a function...

It's (Zipped) in the Bag

Science.gov (United States)

Moyer, Richard H.; Everett, Susan A.

2011-01-01

Plastic baggies, especially the sealable variety, seem to be a ubiquitous part of human culture. The zipper-type seal on plastic baggies is an example of an unappreciated engineering accomplishment that is relevant to everyday life. In fact, the challenge of fastening two pieces together probably dates back to the making of tools and clothing by…

Chapter 23: Corrosion of Metals in Wood Products

Science.gov (United States)

Samuel L. Zelinka

2014-01-01

The corrosion of metals in contact with wood has been studied for over 80 years, and in most situations wood is not corrosive [1]. Recently, however, the durability of fasteners in preservative--treated wood has become a concern. Changes in legislation and certification in the United States, the European Union, and Australasia have restricted the use of chromated...

Design and development of a work robot to place ATLAS SCT modules onto barrel cylinders

International Nuclear Information System (INIS)

Terada, S.; Kobayashi, H.; Sengoku, H.; Kato, Y.; Hara, K.; Honma, F.; Ikegami, Y.; Iwata, Y.; Kohriki, T.; Kondo, T.; Nakano, I.; Takashima, R.; Tanaka, R.; Ujiie, N.; Unno, Y.; Yasuda, S.

2005-01-01

More than 2000 silicon modules need to be placed and fastened on the ATLAS SCT barrel tracker. A semi-automatic pick-and-place work robot was designed and developed to cope with the module placement for the SCT barrel assembly. We found that this robot could place modules to a mechanical precision of better than 25 μm

36 CFR 4.15 - Safety belts.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Safety belts. 4.15 Section 4... TRAFFIC SAFETY § 4.15 Safety belts. (a) Each operator and passenger occupying any seating position of a motor vehicle in a park area will have the safety belt or child restraint system properly fastened at...

46 CFR 58.03-1 - Incorporation by reference.

Science.gov (United States)

2010-10-01

... Drilling Wells, 1984 (“API RP 53”), 58.60-7. (f) American Society of Mechanical Engineers (ASME... Commercial Craft, 1989 (“NFPA 302”), 58.10-5; and (2) [Reserved] (j) Society of Automotive Engineers (SAE..., Mechanical and Material Requirements for Externally Threaded Fasteners (Aug. 1983) (“SAE J429”), 58.30-15. (k...

Research Out On What Buyers of Used Pallets Think

Science.gov (United States)

Robert J. Bush; Ronen Roudik; Philip A. Araman

1995-01-01

Preliminary findings from a new study on repaired pallets indicate that pallet users donât like half companion stringers, split deckboards and protruding fasteners. There has been an awareness for some time that buyers of repaired/recycled pallets prefer to receive pallets that are "like new". However, the reality of the business is that repaired/recycled...

33 CFR 207.260 - Yazoo Diversion Canal, Vicksburg, Miss., from its mouth at Kleinston Landing to Fisher Street...

Science.gov (United States)

2010-07-01

... fastened with chains or wire rope that it cannot be separated or bag out or materially change its shape... route. Rafts shall not be of greater dimensions than 50 feet wide by 600 feet long, and if longer than 300 feet they shall be handled by two tugs; and in all cases they must be handled by sufficient tug...

Testing and evaluation of a slot and tab construction technique for light-weight wood-fiber-based structural panels under bending

Science.gov (United States)

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2015-01-01

This paper presented construction and strain distributions for light-weight wood-fiber-based structural panels with tri-grid core made from phenolic impregnated laminated paper composites under bending. A new fastening configuration of slots in the faces and tabs on the core was applied to the face/core interfaces of the sandwich panel in addition to epoxy resin. Both...

46 CFR 160.043-4 - Construction and workmanship.

Science.gov (United States)

2010-10-01

... of the blade shall be polished. (d) Linings and center. Linings and center shall be not less than 0... from the end of the knife. The shackle shall be attached to the knife by a solid nickel-silver pin not... and fastened to the linings by two solid rivets countersunk on the inside of the linings and smoothly...

Effect of introduction of single-donor apheresis platelets in dengue management: A comparative analysis of two consecutive dengue epidemics

Directory of Open Access Journals (Sweden)

Sonam Kansay

2018-01-01

CONCLUSION: Decision for initiating platelet transfusions and calculating its dose for dengue patients is highly variable, but transfusing high-dose platelets such as SDAP at an appropriate stage can reduce further requirement of platelet transfusions, fasten the recovery, reduce the hospital stay, lower the risk of transfusion-associated adverse reactions, and can further minimize the associated morbidity and mortality.

A Thorough Scrutiny of ELT Textbook Evaluations: A Review Inquiry

Science.gov (United States)

Gholami, Reza; Noordin, Nooreen; Rafik-Galea, Shameem

2017-01-01

It is thoroughly agreed that English language textbooks stand amongst the foremost components in any language classrooms worldwide, being referred to as valid, beneficial and labor-saving tools to fulfill an extensive range of needs. An ELT textbook is not merely a set of sheets of paper fastened together to hinge at one side, but is the beating…

Fabrication of a pressurized water reactor fuel element prototype with Zy-control rod guide tubes

International Nuclear Information System (INIS)

Bezold, H.; Romeiser, H.J.

1978-10-01

A prototype fuel assembly with zircaloy guide was fabricated by mass production methods. The fastening of the Inconel spacer grids to the guide tubes and the transition joint for fixing the tubes to the stainless stell upper end-fitting of the assembly were investigated. Tools and welding devices were developed for the construction of the skeleton. (orig.) [de

Design and development of a work robot to place ATLAS SCT modules onto barrel cylinders

CERN Document Server

Terada, S; Honma, F; Ikegami, Y; Iwata, Y; Kato, Y; Kobayashi, H; Kohriki, T; Kondo, T; Nakano, I; Sengoku, H; Takashima, R; Tanaka, R; Ujiie, N; Unno, Y; Yasuda, S

2005-01-01

More than 2000 silicon modules need to be placed and fastened on the ATLAS SCT barrel tracker. A semi-automatic pick-and-place work robot was designed and developed to cope with the module placement for the SCT barrel assembly. We found that this robot could place modules to a mechanical precision of better than 25 mum.

Untitled

Indian Academy of Sciences (India)

metal concave mirror fastened behind the 1,500 watt Osram lamp and a condensing lens in front of it secured this intense beam of light. The initial assimilation value under this light is 16840 mgm. showing a slight depres- sion below the maximal level of assimilation reached in a light of 68,760. M.C. in Experiment III.

Is tool-making knowledge robust over time and across problems?

Science.gov (United States)

Beck, Sarah R.; Cutting, Nicola; Apperly, Ian A.; Demery, Zoe; Iliffe, Leila; Rishi, Sonia; Chappell, Jackie

2014-01-01

In three studies, we explored the retention and transfer of tool-making knowledge, learnt from an adult demonstration, to other temporal and task contexts. All studies used a variation of a task in which children had to make a hook tool to retrieve a bucket from a tall transparent tube. Children who failed to innovate the hook tool independently saw a demonstration. In Study 1, we tested children aged 4–6 years (N = 53) who had seen the original demonstration 3 months earlier. Performance was excellent at the second time, indicating that children’s knowledge was retained over the 3 month period. In Studies 2 and 3 we explored transfer of the new knowledge to other tasks. In Study 2, children were given two variants of the apparatus that differed in surface characteristics (e.g., shape and color). Participants generalized their knowledge to these new apparatuses even though the new pipecleaner also differed in size and color. Five- to 6-year-olds (N = 22) almost always transferred their knowledge to problems where the same tool had to be made. Younger, 3- to 5-year-olds’ (N = 46), performance was more variable. In Study 3, 4- to 7-year-olds (N = 146) saw a demonstration of hook making with a pipecleaner, but then had to make a tool by combining pieces of wooden dowel (or vice versa: original training on dowel, transfer to pipecleaner). Children did not transfer their tool-making knowledge to the new material. Children retained tool-making knowledge over time and transferred their knowledge to new situations in which they needed to make a similar tool from similar materials, but not different materials. We concluded that children’s ability to use tool-making knowledge in novel situations is likely to depend on memory and analogical reasoning, with the latter continuing to develop during middle childhood. PMID:25538650

Is tool-making knowledge robust over time and across problems?

Directory of Open Access Journals (Sweden)

Sarah Ruth Beck

2014-12-01

Full Text Available In three studies, we explored the retention and transfer of tool-making knowledge, learnt from an adult demonstration, to other temporal and task contexts. All studies used a variation of a task in which children had to make a hook tool to retrieve a bucket from a tall transparent tube. Children who failed to innovate the hook tool independently saw a demonstration.In Study 1, we tested children aged 4 to 6 years (N = 53 who had seen the original demonstration 3 months earlier. Performance was excellent at the second time, indicating that children’s knowledge was retained over the 3 month period. In Studies 2 and 3 we explored transfer of the new knowledge to other tasks. In Study 2, children were given two variants of the apparatus that differed in surface characteristics (e.g. shape and colour. Participants generalised their knowledge to these new apparatuses even though the new pipecleaner also differed in size and colour. Five- to 6-year-olds (n = 22 almost always transferred their knowledge to problems where the same tool had to be made. Younger, 3- to 5-year-olds’ (n = 46, performance was more variable. In Study 3, 4- to 7-year-olds (N = 146 saw a demonstration of hook making with a pipecleaner, but then had to make a tool by combining pieces of wooden dowel (or vice versa: original training on dowel, transfer to pipecleaner. Children did not transfer their tool-making knowledge to the new material. Children retained tool-making knowledge over time and transferred their knowledge to new situations in which they needed to make a similar tool from similar materials, but not different materials. We concluded that children’s ability to use tool-making knowledge in novel situations is likely to depend on memory and analogical reasoning, with the latter continuing to develop during middle childhood.

Design of the First Italian Roundabout with Jointed Plain Concrete Pavement

Directory of Open Access Journals (Sweden)

Paola Di Mascio

2018-02-01

Full Text Available This work presents the results of the overall design of the first Italian roundabout with jointed plain concrete pavement. The examined case study complies with current international standards and practices for geometry of roundabouts and road pavements. The construction of a concrete pavement in an urban roundabout will better manage and slow down fast vehicular flows, and increase traffic fluidity in an important junction, trafficked by heavy vehicles, where maintenance works should be reduced to avoid queues. The design of the roundabout involved several competences for: defining the geometry of the four-arm junction, designing the thickness of the jointed plain concrete pavement both on the circular crown and the arms, studying the mix design of a high resistance concrete. As regard to the pavement, the result of the study was an un-dowelled concrete pavement composed of square slabs laid on a cement concrete subbase and a granular layer. The shape of the slabs has been designed to optimize the structural performance of their material, which is a high strength concrete mix derived from an extensive laboratory test work. In general, the results summarized approaches typical of different design conditions: urban ones for traffic flow and safety needs; high-traffic ones for the chosen pavement type; airport ones for the absence of dowel and tie bars at the joints. Indeed, the article has highlighted that the design process of a concrete roundabout requires multiple analyses to consider various features and correctly re-design an existing urban junction. Its geometrical design, the structural design of the concrete pavement and the theoretical and experimental design of the concrete mix were the main phases of this process and they needed different competences to conduct comprehensive and appropriate analyses.

Corrosion behaviours of the dental magnetic keeper complexes made by different alloys and methods.

Science.gov (United States)

Wu, Min-Ke; Song, Ning; Liu, Fei; Kou, Liang; Lu, Xiao-Wen; Wang, Min; Wang, Hang; Shen, Jie-Fei

2016-09-29

The keeper and cast dowel-coping, as a primary component for a magnetic attachment, is easily subjected to corrosion in a wet environment, such as the oral cavity, which contains electrolyte-rich saliva, complex microflora and chewing behaviour and so on. The objective of this in vitro study was to examine the corrosion resistance of a dowel and coping-keeper complex fabricated by finish keeper and three alloys (cobalt-chromium, CoCr; silver-palladium-gold, PdAu; gold-platinum, AuPt) using a laser-welding process and a casting technique. The surface morphology characteristics and microstructures of the samples were examined by means of metallographic microscope and scanning electron microscope (SEM). Energy-dispersive spectroscopy (EDS) with SEM provided elements analysis information for the test samples after 10% oxalic acid solution etching test. Tafel polarization curve recordings demonstrated parameter values indicating corrosion of the samples when subjected to electrochemical testing. This study has suggested that massive oxides are attached to the surface of the CoCr-keeper complex but not to the AuPt-keeper complex. Only the keeper area of cast CoCr-keeper complex displayed obvious intergranular corrosion and changes in the Fe and Co elements. Both cast and laser-welded AuPt-keeper complexes had the highest free corrosion potential, followed by the PdAu-keeper complex. We concluded that although the corrosion resistance of the CoCr-keeper complex was worst, the keeper surface passive film was actually preserved to its maximum extent. The laser-welded CoCr- and PdAu-keeper complexes possessed superior corrosion resistance as compared with their cast specimens, but no significant difference was found between the cast and laser-welded AuPt-keeper complexes. The Fe-poor and Cr-rich band, appearing on the edge of the keeper when casting, has been proven to be a corrosion-prone area.

Investigation of Miter Corner Joint Strength of Case Furniture from Particleboard

Directory of Open Access Journals (Sweden)

Valdas NORVYDAS

2012-12-01

Full Text Available Most pieces of case furniture (kitchen and bathroom furniture, cabinets, wardrobes, tables and etc. are made of 18 mm thick wood particle boards finished with various coatings. This three-layered constructional material is obtained by bonding wood particles of different fractions with synthetic resins using heating. The exploitation duration and quality of case furniture is determined by the mechanical properties of wood particle boards and the construction of joints of wood-based panels. On a frequent basis, pieces of case furniture with non-dismantable and dismantable construction are joined by using multidowel glued joints and cam connecting fittings intended for furniture, respectively. Wood-based panels can be joined with mitre joints whose mechanical properties have not undergone testing and comparison with regular joints when applying insertable wooden dowels or furniture connecting fittings. During the testing of particle board properties it was established that joining wood-based panels in this way ensures most efficient use of mechanical characteristics of the particleboard. In addition to the properties of the mitre joint, the tests also allowed determining the bending strength, tensile strength and bonding strength of the constructional material, and providing an original method for testing board properties, which can be successfully applied to the prediction of properties of the mitre joint. Tests were performed by using a universal tensile testing machine P-0.5. Joints were bonded by applying PVA dispersion. The surface of boards was veneered by using mahogany veneer and urea formaldehyde resin. It was found that mitre joints of wood particle boards can withstand loads that are higher from 2 to 4 times, in comparison to glued doweled joints or joints constructed with cam connecting fittings.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3095

Effects of accuracy constraints on reach-to-grasp movements in cerebellar patients.

Science.gov (United States)

Rand, M K; Shimansky, Y; Stelmach, G E; Bracha, V; Bloedel, J R

2000-11-01

Reach-to-grasp movements of patients with pathology restricted to the cerebellum were compared with those of normal controls. Two types of paradigms with different accuracy constraints were used to examine whether cerebellar impairment disrupts the stereotypic relationship between arm transport and grip aperture and whether the variability of this relationship is altered when greater accuracy is required. The movements were made to either a vertical dowel or to a cross bar of a small cross. All subjects were asked to reach for either target at a fast but comfortable speed, grasp the object between the index finger and thumb, and lift it a short distance off the table. In terms of the relationship between arm transport and grip aperture, the control subjects showed a high consistency in grip aperture and wrist velocity profiles from trial to trial for movements to both the dowel and the cross. The relationship between the maximum velocity of the wrist and the time at which grip aperture was maximal during the reach was highly consistent throughout the experiment. In contrast, the time of maximum grip aperture and maximum wrist velocity of the cerebellar patients was quite variable from trial to trial, and the relationship of these measurements also varied considerably. These abnormalities were present regardless of the accuracy requirement. In addition, the cerebellar patients required a significantly longer time to grasp and lift the objects than the control subjects. Furthermore, the patients exhibited a greater grip aperture during reach than the controls. These data indicate that the cerebellum contributes substantially to the coordination of movements required to perform reach-to-grasp movements. Specifically, the cerebellum is critical for executing this behavior with a consistent, well-timed relationship between the transport and grasp components. This contribution is apparent even when accuracy demands are minimal.

Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

DOD Review of Flight Safety Critical Threaded Fasteners and Components

National Research Council Canada - National Science Library

Granetto, Paul

2001-01-01

This audit was conducted in response to allegations made to the Defense Hotline in October 1999, that the DoD acquisition and quality assurance procedures allowed significant amounts of dimensionally...

Moment Capacity of Timber Reinforced with Punched Metal Plate Fasteners

DEFF Research Database (Denmark)

Nielsen, Jacob; Ellegaard, Peter

When designing timber trusses it is often found that the cross section controlling the dimensions of the top chord is located at a joint with a moment peak. However, the timber volume affected by the moment peak is rather limited and by embedding a punched metal plate in this area a reinforcement...... of the section is obtained, resulting in a more economic truss design. In order to develop design methods for sections with plate reinforcement, bending tests have been made. The timber is Swedish spruce of strength class K-18(S8) and K-24(S10) with a thickness of 45 mm. The punched metal plate is from Gang...

An alternative fabrication method of the dart thrower's motion orthosis (also known as the dart orthosis).

Science.gov (United States)

Schwartz, Deborah A

2016-01-01

To allow safe early wrist motion after wrist injury, this author has modified an earlier version of a dart thrower's motion orthotic device using material that is currently available on the market and an inexpensive paper fastener as the rivet. - KristinValdes, OTD, OT, CHT, Practice Forum Editor. Copyright © 2016 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Spectrometer for the analysis of radiation, emitted by an X-ray source, by means of an analyzer crystal and a rotating detector

International Nuclear Information System (INIS)

Guernet, J.; Boissel, P.

1979-01-01

The detector is kept tangential to the Rowland circle by means of a mechanical device. For this purpose the device is provided with a support plate for the detector which is fastened to a guiding arm and for which the angular position of the crystal is determined with the aid of a transmission gear having a transmission ratio of 2:1. (DG) [de

Advances in corrosion testing of metals in contact with treated wood

Science.gov (United States)

Samuel Zelinka; D.S. Stone

2010-01-01

A January 2004 change in the regulation of wood preservatives used in the U.S.has increased the use of newer wood preservatives, such as alkaline copper quaternary (ACQ) and copper azole (CuAz). These preservatives contain high amounts of cupric ions, which may be reduced to copper metal at the expense of less noble steel and galvanized fasteners in the wood....

The Problem of the Instrument Stabilization During Hydrographic Measurements

Directory of Open Access Journals (Sweden)

Felski Andrzej

2016-06-01

Full Text Available Performing any measurement on watercraft is connected with many additional difficulties caused by the sea-environment. The most important is the problem of spatial stabilization of measurement systems, which are usually fastened to craft body. As soon as usually these measurement are executed during the move of the craft additional question is the accuracy of execution the planed trajectory.

Ion beam alignment in the MSX-4 mass spectrometer

International Nuclear Information System (INIS)

Busygin, A.I.; Nevzorov, A.A.; Ul'masbaev, B.Sh.

1977-01-01

A method for electrically adjusting an ion beam in an MSKh-4 mass-spectrometer has been developed. The adjusting system consists of two deflecting plates fastened to the frame of the ion source. By adjusting the potential difference at the plates in the range 0-150 v, one can increase the intensity of the mass-spectrum by a factor of 3 to 5

Assessing Worker Exposures during Composite Material and Fiberglass Repair: A Special

Science.gov (United States)

2015-01-01

OEEL, without regard to the use of respirators, shall have shower facilities or other suitable decontamination available [32]. 6.4.2 Dust Removal...use mechanically fastened aluminum or stainless steel patches to repair composite material damage, or repair the composite material damage using...world CBRN environment. If the vacuum mechanism of ventilated tools becomes contaminated with radioactive particulates or chemical/biological agents

Testing and modeling dowel and catenary action in rebars crossing shear joints in RC

DEFF Research Database (Denmark)

Sørensen, Jesper Harrild; Hoang, Linh Cao; Olesen, John Forbes

2017-01-01

presents a simple, second order plasticity model to describe the non-linear regime of the load-displacement relationship. In the model, kinematic relations and the normality condition of plastic theory are utilized to establish a unique link between the imposed shear displacement and combinations of moment...

An Analysis of Derivational Affixes in Commencement speech By Steve Jobs

Directory of Open Access Journals (Sweden)

Dedi Rahman Nur

2016-09-01

Full Text Available The study expects to an investigation of derivational appends in the content of initiation discourse by Steve Jobs. The essayist utilized the majority of the words that were connected prefix and postfix as the information. The information sources were all content of initiation discourse by Steve Jobs. This study utilizing subjective plan and substance investigation approach. The aftereffect of the study demonstrated that there were 78 all out words in the content of Commencement discourse which joined derivational fastens. The study discovered 69 postfixes and 9 prefixes. The foundations of the words that has been grouped in light of the grammatical feature are 17 (descriptor, 27 (thing, 33 (verb, 1 (adverb.From the finish of this study, the author proposes that to enhance their dominance of vocabulary, the perusers ought to apply the derivational fastens by breaking the word into its components root and attaches in light of the fact that from single word they can get the structure of words and them additionally discover how the words fabricated. By knowing the roots, the perusers can assemble the word without anyone else's input

Rotating flux-focusing eddy current probe for flaw detection

Science.gov (United States)

Wincheski, Russell A. (Inventor); Fulton, James P. (Inventor); Nath, Shridhar C. (Inventor); Simpson, John W. (Inventor); Namkung, Min (Inventor)

1997-01-01

A flux-focusing electromagnetic sensor which uses a ferromagnetic flux-focusing lens simplifies inspections and increases detectability of fatigue cracks about circular fasteners and other circular inhomogeneities in high conductivity material. The unique feature of the device is the ferrous shield isolating a high-turn pick-up coil from an excitation coil, The use of the magnetic shield is shown to produce a null voltage output across the receiving coil in the presence of an unflawed sample. A redistribution of the current flow in the sample caused by the presence of flaws, however, eliminates the shielding condition and a large output voltage is produced, yielding a clear unambiguous flaw signal. By rotating the probe in a path around a circular fastener such as a rivet while maintaining a constant distance between the probe and the center of a rivet, the signal due to current flow about the rivet can be held constant. Any further changes in the current distribution, such as due to a fatigue crack at the rivet joint, can be detected as an increase in the output voltage above that due to the flow about the rivet head.

Flux-focusing eddy current probe and rotating probe method for flaw detection

Science.gov (United States)

Wincheski, Buzz A.; Fulton, James P.; Nath, Shridhar C.; Simpson, John W.; Namkung, Min

1994-11-01

A flux-focusing electromagnetic sensor which uses a ferromagnetic flux-focusing lens simplifies inspections and increases detectability of fatigue cracks about circular fasteners and other circular inhomogeneities in high conductivity material. The unique feature of the device is the ferrous shield isolating a high-turn pick-up coil from an excitation coil. The use of the magnetic shield is shown to produce a null voltage output across the receiving coil in the presence of an unflawed sample. A redistribution of the current flow in the sample caused by the presence of flaws, however, eliminates the shielding condition and a large output voltage is produced, yielding a clear unambiguous flaw signal. By rotating the probe in a path around a circular fastener such as a rivet while maintaining a constant distance between the probe and the center of a rivet, the signal due to current flow about the rivet can be held constant. Any further changes in the current distribution, such as due to a fatigue crack at the rivet joint, can be detected as an increase in the output voltage above that due to the flow about the rivet head.

An investigation into the anti-releasing performance of a serrated bolt

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jin Hwan; Lee, Hyun Kyu; Park, Ke Un; Kim, Jong Bong [Seoul Natinal University, Seoul (Korea, Republic of)

2015-11-15

As the sizes of electric products, such as mobile phones and watch phones, decrease, the joining bolt for the electric product should also be miniaturized. However, the miniature-sized bolt has to support sufficient joining torque and joining force. The bolt also has to support sufficient anti-releasing torque to keep the product fastened. We investigated a serrated bolt as a candidate for a miniature-sized fastener to increase the anti-release torque. In the serrated bolt, serration shapes are formed on the bottom surface of a bolt head to create an obstacle to releasing. In this study, finite element analyses were carried out on joining and releasing, and the anti-release torque was predicted. Through the joining and releasing analyses for various values of the elastic modulus and yield strength of the joined part, the effect of the mechanical properties of the joined part on the anti-releasing performance were investigated. The analysis results showed that a high strength insert nut is needed to increase the anti-releasing torque when the yield strength of the joined part is low, such as a plastic board in a mobile phone.

16 CFR 1616.5 - Test procedure.

Science.gov (United States)

2010-01-01

... metal hooks consist of No. 19 gauge steel wire, or equivalent, made from 7.6 cm. (3 in.) lengths of the wire, bent 1.3 cm. (0.5 in.) from one end to a 45-degree angle hook. The longer end of the wire is fastened around the neck of the weight to be used and the other in the lower end of each burned specimen to...

Device for stretching tapes or cables intended for manipulators

International Nuclear Information System (INIS)

Baudoin, J.-C.; Oger, Robert.

1975-01-01

The invention relates to a device for stretching tapes (or cables) intended for remote handling devices. Said equipment consists of a spring system continuously applying a constant tensile stress to said tapes (or cables) in view of taking up the slack in the latter. Said spring system is fastened to a supporting bar able to be rigidly connected to a member of the remote handling device [fr