Improvement in crystallization and electrical properties of barium strontium titanate thin films by gold doping using metal-organic deposition method

International Nuclear Information System (INIS)

Wang, H.-W.; Nien, S.-W.; Lee, K.-C.; Wu, M.-C.

2005-01-01

The effect of gold (Au) on the crystallization, dielectric constant and leakage current density of barium strontium titanate (BST) thin films was investigated. BST thin films with various gold concentrations were prepared via a metal-organic deposition process. The X-ray diffraction shows enhanced crystallization as well as expanded lattice constants for the gold-doped BST films. Thermal analysis reveals that the gold dopant induces more complete decomposition of precursor for the doped films than those of undoped ones. The leakage current density of BST films is greatly reduced by the gold dopant over a range of biases (1-5 V). The distribution of gold was confirmed by electron energy loss spectroscopy and found to be inside the BST grains, not in the grain-boundaries. Gold acted as a catalyst, inducing the nucleation of crystallites and improving the crystallinity of the structure. Its addition is shown to be associated to the improvement of the electrical properties of BST films

Microwave-hydrothermal synthesis of barium strontium titanate nanoparticles

International Nuclear Information System (INIS)

Simoes, A.Z.; Moura, F.; Onofre, T.B.; Ramirez, M.A.; Varela, J.A.; Longo, E.

2010-01-01

Research highlights: → Barium strontium titanate nanoparticles were obtained by the Hydrothemal microwave technique (HTMW) → This is a genuine technique to obtain nanoparticles at low temperature and short times → Barium strontium titanate free of carbonates with tetragonal structure was grown at 130 o C. - Abstract: Hydrothermal-microwave method (HTMW) was used to synthesize crystalline barium strontium titanate (Ba 0.8 Sr 0.2 TiO 3 ) nanoparticles (BST) in the temperature range of 100-130 o C. The crystallization of BST with tetragonal structure was reached at all the synthesis temperatures along with the formation of BaCO 3 as a minor impurity at lower syntheses temperatures. Typical FT-IR spectra for tetragonal (BST) nanoparticles presented well defined bands, indicating a substantial short-range order in the system. TG-DTA analyses confirmed the presence of lattice OH- groups, commonly found in materials obtained by HTMW process. FE/SEM revealed that lower syntheses temperatures led to a morphology that consisted of uniform grains while higher syntheses temperature consisted of big grains isolated and embedded in a matrix of small grains. TEM has shown BST nanoparticles with diameters between 40 and 80 nm. These results show that the HTMW synthesis route is rapid, cost effective, and could serve as an alternative to obtain BST nanoparticles.

Enhancement of tetragonality and role of strontium vacancies in heterovalent doped SrTiO.sub.3./sub..

Czech Academy of Sciences Publication Activity Database

Tkach, A.; Almeida, A.; Moreira, J.A.; Correia, T.M.; Chaves, M. R.; Okhay, O.; Vilarinho, P. M.; Gregora, Ivan; Petzelt, Jan

2011-01-01

Roč. 98, č. 5 (2011), "052903-1"-"052903-2" ISSN 0003-6951 R&D Projects: GA AV ČR KAN301370701 Institutional research plan: CEZ:AV0Z10100520 Keywords : strontium titanate * doping * phase transition * Raman spectroscopy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.844, year: 2011

Thermal Transport and Phonon Hydrodynamics in Strontium Titanate

Science.gov (United States)

Martelli, Valentina; Jiménez, Julio Larrea; Continentino, Mucio; Baggio-Saitovitch, Elisa; Behnia, Kamran

2018-03-01

We present a study of thermal conductivity, κ , in undoped and doped strontium titanate in a wide temperature range (2-400 K) and detecting different regimes of heat flow. In undoped SrTiO3 , κ evolves faster than cubic with temperature below its peak and in a narrow temperature window. Such behavior, previously observed in a handful of solids, has been attributed to a Poiseuille flow of phonons, expected to arise when momentum-conserving scattering events outweigh momentum-degrading ones. The effect disappears in the presence of dopants. In SrTi1 -xNbx O3 , a significant reduction in lattice thermal conductivity starts below the temperature at which the average inter-dopant distance and the thermal wavelength of acoustic phonons become comparable. In the high-temperature regime, thermal diffusivity becomes proportional to the inverse of temperature, with a prefactor set by sound velocity and Planckian time (τp=(ℏ/kBT ) ).

Lanthanum-doped mesostructured strontium titanates synthesized via sol–gel combustion route using citric acid as complexing agent

Energy Technology Data Exchange (ETDEWEB)

Sukpanish, Polthep [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Center of Excellence on Petrochemical and Materials Technology (PETROMAT), Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Lertpanyapornchai, Boontawee [Program in Petrochemistry, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Yokoi, Toshiyuki [Division of Catalytic Chemistry, Chemical Resources Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Ngamcharussrivichai, Chawalit, E-mail: Chawalit.Ng@chula.ac.th [Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Center of Excellence on Petrochemical and Materials Technology (PETROMAT), Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand)

2016-09-15

In the present work, a series of lanthanum-doped mesostructured strontium titanate (LMST) materials with different La/Sr ratios were synthesized via a sol–gel combustion method in the presence of citric acid as a complexing agent and Pluronic P123 as a templating agent. The effects of the amount of doped La and calcination temperature on the physicochemical properties of the LMSTs were examined using various techniques. Powder X-ray diffraction confirmed the substitution of La{sup 3+} into the SrTiO{sub 3} lattice, generating cubic perovskite La{sub x}Sr{sub 1−x}TiO{sub 3}, for the LMST materials calcined at 600 °C. The purity and crystallinity of the desired perovskite phase were enhanced by citric acid addition. The solubility limit of La{sup 3+} substitution at an La/Sr ratio of 0.43 was determined by structural and morphological studies. Increasing the La doping amount decreased the crystallinity and compositional homogeneity, because an La-rich amorphous phase segregated on the surface, but improved the mesoporosity. N{sub 2} physisorption measurements indicated that the LMSTs had a bimodal pore size distribution, of which the larger one was characterized by the crystallite size of mixed oxides, and the specific surface area of 24.9–37.3 m{sup 2} g{sup −1}. The formation of mesopores in the LMST materials synthesized via sol–gel combustion was explained based on a combination of soft- and hard-templating chemistries. - Highlights: • La-doped mesoporous SrTiO{sub 3} (LMST) was prepared first time via sol-gel combustion. • Pluronic P123 triblock copolymer was used as a cheap templating agent. • Citric acid as a complexing agent enhanced the purity and crystallinity of SrTiO{sub 3}. • The textural properties of LMST were improved by increasing the La doping amount. • Mesopore formation was explained by a combined soft- and hard-templating route.

Effect of multi-layered bottom electrodes on the orientation of strontium-doped lead zirconate titanate thin films

Energy Technology Data Exchange (ETDEWEB)

Bhaskaran, M. [Microelectronics and Materials Technology Centre, School of Electrical and Computer Engineering, RMIT University, GPO Box 2476V, Melbourne, Victoria 3001 (Australia)], E-mail: madhu.bhaskaran@gmail.com; Sriram, S. [Microelectronics and Materials Technology Centre, School of Electrical and Computer Engineering, RMIT University, GPO Box 2476V, Melbourne, Victoria 3001 (Australia); Mitchell, D.R.G.; Short, K.T. [Institute of Materials Engineering, Australian Nuclear Science and Technology Organisation (ANSTO), PMB 1, Menai, New South Wales 2234 (Australia); Holland, A.S. [Microelectronics and Materials Technology Centre, School of Electrical and Computer Engineering, RMIT University, GPO Box 2476V, Melbourne, Victoria 3001 (Australia)

2008-09-30

This article discusses the results from X-ray diffraction (XRD) analysis of piezoelectric strontium-doped lead zirconate titanate (PSZT) thin films deposited on multi-layer coatings on silicon. The films were deposited by RF magnetron sputtering on a metal coated substrate. The aim was to exploit the pronounced piezoelectric effect that is theoretically expected normal to the substrate. This work highlighted the influence that the bottom electrode architecture exerts on the final crystalline orientation of the deposited thin films. A number of bottom electrode architectures were used, with the uppermost metal layer on which PSZT was deposited being gold or platinum. The XRD analysis revealed that the unit cell of the PSZT thin films deposited on gold and on platinum were deformed, relative to expected unit cell dimensions. Experimental results have been used to estimate the unit cell parameters. The XRD results were then indexed based on these unit cell parameters. The choice and the thickness of the intermediate adhesion layers influenced the relative intensity, and in some cases, the presence of perovskite peaks. In some cases, undesirable reactions between the bottom electrode layers were observed, and layer architectures to overcome these reactions are also discussed.

Synthesis and characterization of Ho{sup 3+}-doped strontium titanate downconversion nanocrystals and its application in dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Li, Y.Y. [Department of Inorganic Nonmetallic Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Liaoning Provincial College Key Laboratory of New Materials and Material Modification, Dalian Polytechnic University, Dalian 116034 (China); Hao, H.S., E-mail: beike1952@163.com [Department of Inorganic Nonmetallic Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Liaoning Provincial College Key Laboratory of New Materials and Material Modification, Dalian Polytechnic University, Dalian 116034 (China); Qin, L. [National Engineering Research Center of Seafood, Dalian Polytechnic University, Dalian 116034 (China); Wang, H.L.; Nie, M.Q.; Hu, Z.Q.; Gao, W.Y.; Liu, G.S. [Department of Inorganic Nonmetallic Materials Engineering, Dalian Polytechnic University, Dalian 116034 (China); Liaoning Provincial College Key Laboratory of New Materials and Material Modification, Dalian Polytechnic University, Dalian 116034 (China)

2015-02-15

Highlights: • A new downconversion (DC) nanocrystal (SrTiO{sub 3}:Ho{sup 3+}) was synthesized. • The effect of SrTiO{sub 3}:Ho{sup 3+} as a photoanode in DSSCs was investigated. • SrTiO{sub 3}:Ho{sup 3+} absorb ultraviolet light and downconvert it to visible light. • DC SrTiO{sub 3}:Ho{sup 3+} as a photoanode achieve the higher photoelectric conversion efficiency. - Abstract: Ho{sup 3+}-doped strontium titanate (SrTiO{sub 3}:Ho{sup 3+}) downconversion (DC) nanocrystals are synthesized by the solid state interaction of titanium dioxide, strontium nitrate, holmium oxide and sodium chloride and then used as a photoanode in dye-sensitized solar cells (DSSCs) to investigate the effect of DC nanocrystals in DSSCs. Differential thermal analysis, X-ray diffraction, scanning electronic microscope, energy dispersive spectroscopy and Brunauer-Emmet-Teller analysis confirmed the formation of cubic structured SrTiO{sub 3}:Ho{sup 3+} nanocrystals with diameters of 40-400 nm, pore size of ∼45 nm, sintering temperature of 950 °C. The photofluorescence and UV-Vis absorption spectra of the SrTiO{sub 3}:Ho{sup 3+} nanocrystals revealed strong emission intensity and visible light absorption when doped content of holmium oxide was between 1 wt% and 3 wt%. Compared with the pure SrTiO{sub 3} photoanode, SrTiO{sub 3}:Ho{sup 3+} DC photoanode showed a greater photovoltaic efficiency. The photoelectric conversion efficiency (η) of the DSSCs with a SrTiO{sub 3}:Ho{sup 3+} photoanode doped with 1 wt% holmium oxide was 59% higher than that with a pure SrTiO{sub 3} photoanode. This phenomenon could be explained by SrTiO{sub 3}:Ho{sup 3+} nanocrystals’ ability to absorb ultraviolet light and downconvert it to visible light, which extends spectral response range of DSSC to the ultraviolet region and increased the short-circuit current density (Jsc) of DSSCs.

Anion and cation diffusion in barium titanate and strontium titanate; Anionen- und Kationendiffusion in Barium- und Strontiumtitanat

Energy Technology Data Exchange (ETDEWEB)

Kessel, Markus Franz

2012-12-19

Perovskite oxides show various interesting properties providing several technical applications. In many cases the defect chemistry is the key to understand and influence the material's properties. In this work the defect chemistry of barium titanate and strontium titanate is analysed by anion and cation diffusion experiments and subsequent time-of-flight secondary ion mass spectrometry (ToF-SIMS). The reoxidation equation for barium titanate used in multi-layer ceramic capacitors (MLCCs) is found out by a combination of different isotope exchange experiments and the analysis of the resulting tracer diffusion profiles. It is shown that the incorporation of oxygen from water vapour is faster by orders of magnitude than from molecular oxygen. Chemical analysis shows the samples contain various dopants leading to a complex defect chemistry. Dysprosium is the most important dopant, acting partially as a donor and partially as an acceptor in this effectively acceptor-doped material. TEM and EELS analysis show the inhomogeneous distribution of Dy in a core-shell microstructure. The oxygen partial pressure and temperature dependence of the oxygen tracer diffusion coefficients is analysed and explained by the complex defect chemistry of Dy-doped barium titanate. Additional fast diffusion profiles are attributed to fast diffusion along grain boundaries. In addition to the barium titanate ceramics from an important technical application, oxygen diffusion in cubic, nominally undoped BaTiO{sub 3} single crystals has been studied by means of {sup 18}O{sub 2}/{sup 16}O{sub 2} isotope exchange annealing and subsequent determination of the isotope profiles in the solid by ToF-SIMS. It is shown that a correct description of the diffusion profiles requires the analysis of the diffusion through the surface space-charge into the material's bulk. Surface exchange coefficients, space-charge potentials and bulk diffusion coefficients are analysed as a function of oxygen partial

Implanted strontium titanate single crystals for energy storage applications

Energy Technology Data Exchange (ETDEWEB)

Stoeber, Max; Cherkouk, Charaf; Walter, Juliane; Strohmeyer, Ralph; Leisegang, Tilmann; Meyer, Dirk Carl [TU Bergakademie, Freiberg (Germany); Schelter, Matthias; Zosel, Jens [Kurt Schwabe Institute, Meinsberg (Germany); Prucnal, Slawomir [Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden-Rossendorf (Germany)

2016-07-01

A rapid increase of the demand on efficient energy storage solutions requires new approaches beyond the Li-ion technology. In particular, metal-air batteries as well as solid-state fuel cells offer a great potential for high-energy-density storage devices. Since the efficiency of such devices is significantly limited by the activation of both the oxygen reduction reaction (ORR) and the ionic and electronic conductivities, an adequate porosity as well as a controlled doping are required. The ion implantation is a key technology to achieve this goal. In this work, p- and n-doped strontium titanate (SrTiO{sub 3}) single crystals were used as oxidic materials. The oxygen exchange kinetics as well as the structural changes of the SrTiO{sub 3} crystal surface induced by the ion implantation were investigated. On one hand, the depth profile of dopant concentration and dopant valence state were determined using sputtered X-ray photoelectron spectroscopy (XPS). On the other hand, the overall oxygen exchange kinetic of the implanted SrTiO{sub 3} crystal was quantitatively described by means of coulometric titration using Zirox system (ZIROX GmbH, Germany). Furthermore, the surface morphology of the samples was investigated using atomic force microscopy (AFM).

Spin injection and detection in lanthanum- and niobium-doped SrTiO3 using the Hanle technique

KAUST Repository

Han, Wei

2013-07-08

There has been much interest in the injection and detection of spin-polarized carriers in semiconductors for the purposes of developing novel spintronic devices. Here we report the electrical injection and detection of spin-polarized carriers into Nb-doped strontium titanate single crystals and La-doped strontium titanate epitaxial thin films using MgO tunnel barriers and the three-terminal Hanle technique. Spin lifetimes of up to ∼100 ps are measured at room temperature and vary little as the temperature is decreased to low temperatures. However, the mobility of the strontium titanate has a strong temperature dependence. This behaviour and the carrier doping dependence of the spin lifetime suggest that the spin lifetime is limited by spin-dependent scattering at the MgO/strontium titanate interfaces, perhaps related to the formation of doping induced Ti 3+. Our results reveal a severe limitation of the three-terminal Hanle technique for measuring spin lifetimes within the interior of the subject material. © 2013 Macmillan Publishers Limited. All rights reserved.

Electronic structure of barium strontium titanate by soft-x-ray absorption spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Uehara, Y. [Mitsubishi Electric Co., Hyogo (Japan); Underwood, J.H.; Gullikson, E.M.; Perera, R.C.C. [Ernest Orlando Lawrence Berkeley National Lab., CA (United States)

1997-04-01

Perovskite-type titanates, such as Strontium Titanate (STO), Barium Titanate (BTO), and Lead Titanate (PTO) have been widely studied because they show good electric and optical properties. In recent years, thin films of Barium Strontium Titanate (BST) have been paid much attention as dielectrics of dynamic random access memory (DRAM) capacitors. BST is a better insulator with a higher dielectric constant than STO and can be controlled in a paraelectric phase with an appropriate ratio of Ba/Sr composition, however, few studies have been done on the electronic structure of the material. Studies of the electronic structure of such materials can be beneficial, both for fundamental physics research and for improving technological applications. BTO is a famous ferroelectric material with a tetragonal structure, in which Ti and Ba atoms are slightly displaced from the lattice points. On the other hand, BST keeps a paraelectric phase, which means that the atoms are still at the cubic lattice points. It should be of great interest to see how this difference of the local structure around Ti atoms between BTO and BST effects the electronic structure of these two materials. In this report, the authors present the Ti L{sub 2,3} absorption spectra of STO, BTO, and BST measured with very high accuracy in energy of the absorption features.

Electronic structure of barium strontium titanate by soft-x-ray absorption spectroscopy

International Nuclear Information System (INIS)

Uehara, Y.; Underwood, J.H.; Gullikson, E.M.; Perera, R.C.C.

1997-01-01

Perovskite-type titanates, such as Strontium Titanate (STO), Barium Titanate (BTO), and Lead Titanate (PTO) have been widely studied because they show good electric and optical properties. In recent years, thin films of Barium Strontium Titanate (BST) have been paid much attention as dielectrics of dynamic random access memory (DRAM) capacitors. BST is a better insulator with a higher dielectric constant than STO and can be controlled in a paraelectric phase with an appropriate ratio of Ba/Sr composition, however, few studies have been done on the electronic structure of the material. Studies of the electronic structure of such materials can be beneficial, both for fundamental physics research and for improving technological applications. BTO is a famous ferroelectric material with a tetragonal structure, in which Ti and Ba atoms are slightly displaced from the lattice points. On the other hand, BST keeps a paraelectric phase, which means that the atoms are still at the cubic lattice points. It should be of great interest to see how this difference of the local structure around Ti atoms between BTO and BST effects the electronic structure of these two materials. In this report, the authors present the Ti L 2,3 absorption spectra of STO, BTO, and BST measured with very high accuracy in energy of the absorption features

Impregnation of sodium titanate onto DMAPAA-grafted fiber under mild reaction conditions and its strontium removal performance from seawater

International Nuclear Information System (INIS)

Katagiri, Mizuki; Kono, Michitaka; Goto, Shun-ichi; Kawai-Noma, Shigeko; Umeno, Daisuke; Saito, Kyoichi; Fujiwara, Kunio; Sugo, Takanobu

2015-01-01

Sodium titanate was impregnated onto a commercially available 6-nylon fiber by means of radiation-induced graft polymerization of dimethyaminopropyl acrylamide (DMAPAA) and subsequent chemical modifications. A peroxo complex of titanium anions was bound onto the DMAPAA-grafted fiber before the bound titanium species was converted to sodium titanate through precipitation with sodium hydroxide. Impregnation percentage of sodium titanate of the fiber was constant at 20% in the range of sodium hydroxide concentration in a mixture of methanol and water at a volume fraction of methanol of 80% of 0.001 to 1 M, whereas the removal percentage of strontium from seawater leveled off at 80% above a sodium hydroxide concentration in water of 0.1 M. Determination of adsorption isotherms in seawater demonstrates that the sodium-titanate-impregnated fiber with an impregnation percentage of 10% exhibited 2.6-fold higher amount of strontium adsorbed in seawater per g of sodium titanate (8.8 mg-Sr/g) than a commercially available granular adsorbent for strontium, SrTreat ® (3.4 mg-Sr/g). (author)

Combining x-ray diffraction contrast tomography and mesoscale grain growth simulations in strontium titanate: An integrated approach for the investigation of microstructure evolution

DEFF Research Database (Denmark)

Syha, Melanie; Baürer, Michael; Rheinheimer, Wolfgang

2013-01-01

Motivated by the recently reported a growth anomaly in strontium titatate bulk samples1, the microstructure of bulk strontium titanate has been investigated by an integrated approach comprising conventional metallography, three dimensional X-ray diffraction contrast tomography (DCT)2, and the obs......Motivated by the recently reported a growth anomaly in strontium titatate bulk samples1, the microstructure of bulk strontium titanate has been investigated by an integrated approach comprising conventional metallography, three dimensional X-ray diffraction contrast tomography (DCT)2......, and the observation of pore shapes in combination with mesoscale grain growth simulations. The microstructural evolution in strontium titanate has been characterized alternating ex-situ annealing and high energy X-ray DCT measurements, resulting in three dimensional microstructure reconstructions which...

Effect of donor and acceptor dopants on crystallization, microstructural and dielectric behaviors of barium strontium titanate glass ceramics

Energy Technology Data Exchange (ETDEWEB)

Yadav, Avadhesh Kumar, E-mail: yadav.av11@gmail.com [Department of Physics, Dr. Bheem Rao Ambedkar Government Degree College, Anaugi, Kannauj (India); Gautam, C.R. [Department of Physics, University of Lucknow, Lucknow 226007 (India); Singh, Prabhakar [Department of Physics, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India)

2016-07-05

Bulk transparent barium strontium titanate borosilicate glasses in glass system (65-x)[(Ba{sub 0.6}Sr{sub 0.4}).TiO{sub 3}]-30[2SiO{sub 2}.B{sub 2}O{sub 3}]-5[K{sub 2}O]-x[A{sub 2}O{sub 3}], A = La, Fe (x = 2, 5 and 10) were prepared by rapid melt-quench technique and subsequently, converted into glass ceramics by regulated heat treatment process. The phase identification was carried out by X-ray powder diffraction and their surface morphology was studied by scanning electron microscopy. The dielectric properties were studied by impedance spectroscopic technique. Investigated glass samples were crystallized into major and secondary phases of Ba{sub 1.91}Sr{sub 0.09}TiO{sub 4} and Ba{sub 2}TiSi{sub 2}O{sub 8}, respectively. A very high dielectric constant having value upto 68000 was found in glass ceramic sample BST5K10F. This high value of dielectric constant was attributed to interfacial polarization, which arose due to conductivity difference among semiconducting crystalline phases, conducting grains and insulating grain boundaries. Donor dopant La{sub 2}O{sub 3} and acceptor dopant Fe{sub 2}O{sub 3} play an important role for enhancing crystallization, dielectric constant and retardation of dielectric loss in the samples. Moreover, higher value of dielectric constant and lower value of dielectric loss was found in Fe{sub 2}O{sub 3} doped samples in comparison to La{sub 2}O{sub 3} doped samples. - Highlights: • Bulk transparent barium strontium titanate glasses are successfully prepared. • A very high dielectric constant upto 68000 was found in glass ceramics. • La{sub 2}O{sub 3} and Fe{sub 2}O{sub 3} play role for enhancing value of dielectric constant. • Higher dielectric constant with low dielectric loss was found in Fe{sub 2}O{sub 3} doped sample. • Such glass ceramics may be used in making capacitors for high energy storage.

Microwave-assisted fabrication of strontium doped apatite coating on Ti6Al4V

Energy Technology Data Exchange (ETDEWEB)

Zhou, Huan, E-mail: huanzhou@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); Kong, Shiqin [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); School of Materials Science and Engineering, Changzhou University, Changzhou, Jiangsu 213164 (China); Pan, Yan; Zhang, Zhiguo [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); Deng, Linhong, E-mail: dlh@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China)

2015-11-01

Strontium has been shown to be a beneficial dopant to calcium phosphates when incorporated at nontoxic level. In the present work we studied the possibility of solution derived doping strontium into calcium phosphate coatings on titanium alloy Ti6Al4V based implants by a recently reported microwave-assisted method. By using this method strontium doped calcium phosphate nuclei were deposited to pretreated titanium alloy surface dot by dot to compose a crack-free coating layer. The presence of strontium in solution led to reduced roughness of the coating and finer nucleus size formed. In vitro study found that proliferation and differentiation of osteoblast cells seeded on the coating were influenced by strontium content in coatings, showing an increasing followed by a decreasing behavior with increasing substitution of calcium by strontium. It is suggested that this new microwave-assisted strontium doped calcium phosphate coatings may have great potential in implant modification. - Highlights: • Strontium doped calcium phosphate coating is deposited with microwave irradiation. • Increase of strontium reduces coating roughness and results in finer nucleus size. • Proliferation and differentiation of osteoblasts depend on doped strontium content.

Physicochemical Properties and Cellular Responses of Strontium-Doped Gypsum Biomaterials

OpenAIRE

Pouria, Amir; Bandegani, Hadis; Pourbaghi-Masouleh, Milad; Hesaraki, Saeed; Alizadeh, Masoud

2012-01-01

This paper describes some physical, structural, and biological properties of gypsum bioceramics doped with various amounts of strontium ions (0.19–2.23 wt%) and compares these properties with those of a pure gypsum as control. Strontium-doped gypsum (gypsum:Sr) was obtained by mixing calcium sulfate hemihydrate powder and solutions of strontium nitrate followed by washing the specimens with distilled water to remove residual salts. Gypsum was the only phase found in the composition of both pu...

Barium strontium titanate powders prepared by spray pyrolysis

International Nuclear Information System (INIS)

Brankovic, G.; Brankovic, Z.; Goes, M.S.; Paiva-Santos, C.O.; Cilense, M.; Varela, J.A.; Longo, E.

2005-01-01

Ultasonic spray pyrolysis (SP) has been investigated for the production of the barium strontium titanate (BST) powders from the polymeric precursors. The processing parameters, such as flux of aerosol and temperature profile inside the furnace, were optimized to obtain single phase BST. The powders were characterized by the methods of X-ray diffraction analysis, SEM, EDS and TEM. The obtained powders were submicronic, consisting of spherical, polycrystalline particles, with internal nanocrystalline structure. Crystallite size of 10 nm, calculated using Rietveld refinement, is in a good agreement with results of HRTEM

Effect of the synthesis temperature of sodium nona-titanate on batch kinetics of strontium-ion adsorption from aqueous solution

International Nuclear Information System (INIS)

Merceille, A.; Weinzaepfel, E.; Grandjean, A.; Merceille, A.; Weinzaepfel, E.; Barre, Y.

2011-01-01

Sodium titanate materials are promising inorganic ion exchangers for the adsorption of strontium from aqueous solutions. Sodium nona-titanate exhibits a layered structure consisting of titanate layers and exchangeable sodium ions between the layers. The materials used in this study include samples synthesized by a hydrothermal method at temperatures between 60 degrees C and 200 degrees C. Their structure, composition, and morphology were investigated with X-Ray diffraction measurements; thermogravimetric, compositional and surface area analyses, and scanning electron microscopy. The structure, composition, and morphology depended on the synthesis temperature. Batch kinetics experiments for the removal of strontium from aqueous solutions were performed, and the data were fitted by a pseudo-second-order reaction model and a diffusive model. The strontium extraction capacity also depended on the synthesis temperature and exhibited a maximum for samples synthesized at 100 degrees C. The sorption process occurs in one or two diffusion-controlled steps that also depend on the synthesis temperature. These diffusion-limited steps are the boundary-layer diffusion and intra-particle diffusion in the case of pure nona-titanate synthesized at temperatures lower than 170 degrees C, and only intra-particle diffusion in the case of nona-titanate synthesized at 200 degrees C. (authors)

Assessment of full ceramic solid oxide fuel cells based on modified strontium titanates

DEFF Research Database (Denmark)

Holtappels, Peter; Ramos, Tania; Sudireddy, Bhaskar Reddy

2014-01-01

stimulated the development for full ceramic anodes based on strontium titanates. Furthermore, the Ni-cermet is primarily a hydrogen oxidation electrode and efficiency losses might occur when operating on carbon containing fuels. In the European project SCOTAS-SOFC full ceramic cells comprising CGO...

Growth and characterization of pure and lithium doped strontium ...

Indian Academy of Sciences (India)

TECS

Abstract. The effect of lithium ion as dopant on the size and transparency of strontium tartrate tetrahydrate. (SrC4H4O6⋅4H2O) crystals are presented in this paper. Growth of single crystals of undoped and lithium doped strontium tartrate tetrahydrate by controlled diffusion of strontium nitrate into the gel charged with.

Textured strontium titanate layers on platinum by atomic layer deposition

International Nuclear Information System (INIS)

Blomberg, T.; Anttila, J.; Haukka, S.; Tuominen, M.; Lukosius, M.; Wenger, Ch.; Saukkonen, T.

2012-01-01

Formation of textured strontium titanate (STO) layers with large lateral grain size (0.2–1 μm) and low X-ray reflectivity roughness (∼ 1.36 nm) on Pt electrodes by industry proven atomic layer deposition (ALD) method is demonstrated. Sr(t-Bu 3 Cp) 2 , Ti(OMe) 4 and O 3 precursors at 250 °C were used to deposit Sr rich STO on Pt/Ti/SiO 2 /Si ∅200 mm substrates. After crystallization post deposition annealing at 600 °C in air, most of the STO grains showed a preferential orientation of the {001} plane parallel to the substrate surface, although other orientations were also present. Cross sectional and plan view transmission electron microscopy and electron diffraction analysis revealed more than an order of magnitude larger lateral grain sizes for the STO compared to the underlying multicrystalline {111} oriented platinum electrode. The combination of platinum bottom electrodes with ALD STO(O 3 ) shows a promising path towards the formation of single oriented STO film. - Highlights: ► Amorphous strontium titanate (STO) on platinum formed a textured film after annealing. ► Single crystal domains in 60 nm STO film were 0.2–1 μm wide. ► Most STO grains were {001} oriented.

Characteristics of strontium-doped ZnO films on love wave filter applications

International Nuclear Information System (INIS)

Water, Walter; Yan, Y.-S.

2007-01-01

The effect of dopant concentrations in strontium-doped ZnO films on Love wave filter characteristics was investigated. Strontium-doped ZnO films with a c-axis preferred orientation were grown on ST-cut quartz by radio frequency magnetron sputtering. The crystalline structures and surface morphology of films were studied by X-ray diffraction, scanning electron microscopy and atomic force microscopy. The electromechanical coupling coefficient, dielectric constant, and temperature coefficient of frequency of filters were then determined using a network analyzer. A uniform crystalline structure and smooth surface of the ZnO films were obtained at the 1-2 mol% strontium dopant level. The electromechanical coupling coefficient of the 1 mol% strontium-doped ZnO film reaches a maximum of 0.61%, and the temperature coefficient of frequency declines to + 12.87 ppm/deg. C at a 1.5 mol% strontium dopant level

Lanthanide doped strontium-barium cesium halide scintillators

Science.gov (United States)

Bizarri, Gregory; Bourret-Courchesne, Edith; Derenzo, Stephen E.; Borade, Ramesh B.; Gundiah, Gautam; Yan, Zewu; Hanrahan, Stephen M.; Chaudhry, Anurag; Canning, Andrew

2015-06-09

The present invention provides for a composition comprising an inorganic scintillator comprising an optionally lanthanide-doped strontium-barium, optionally cesium, halide, useful for detecting nuclear material.

Study on the piezoelectric behavior and structural changes of strontium doped PZT

International Nuclear Information System (INIS)

Silva, M.S. da; Lemos, L.; Souza, E.F.; Cavalheiro, A.A.; Longo, E.; Zaghete, M.A.

2014-01-01

Lead zirconate titanate, with Zr/Ti ratio of 53/47 was prepared by the polymeric precursor method. The powders were doped with 0.0, 0.2, 0.4 and 0.6 mol% of Sr 2+ and the effects of Sr 2+ additions on piezoelectric properties and on the phase constitution were investigated by XRD. The percentages of tetragonal and rhombohedral phases were calculated through Rietveld refinement. The results indicated that addition of Sr 2+ ions in the amount of 0.4 mol% in the ceramic structure maximally increase the values of piezoelectric parameter to d 33 = 289 μC/N and K p = 0.43. The values found for the piezoelectric properties were among the highest at the concentration of 0.4 mol% of strontium and this composition showed the highest structural change from the rhombohedral to the tetragonal phase perovskita. (author)

High performance fuel electrode for a solid oxide electrochemical cell

DEFF Research Database (Denmark)

2013-01-01

perovskite oxides selected from the group consisting of niobium-doped strontium titanate, vanadium-doped strontium titanate, tantalum-doped strontium titanate and mixtures thereof, thereby obtaining a porous anode backbone, (b) sintering the coated electrolyte at a high temperature, such as 1200 DEG C...

Observation of potential barriers on barium strontium titanate PTCR ceramics by electrostatic force microscopy

International Nuclear Information System (INIS)

Manfredini, J.P.; Paulin Filho, P.I.; Gheno, S.M.

2011-01-01

A composition of PTCR ceramic based in barium titanate with isovalent replacement of part of barium by strontium using lanthanum and manganese as additives was investigated. The transition temperature, typical of these materials, was shifted below the room temperature by the presence of strontium, whose behavior was detected by tests of DC resistivity and impedance spectroscopy. The observation of potential barriers at grain boundaries was possible through the technique of electrostatic force microscopy (EFM). The results also showed the presence of space charges in regions inside grains, possibly at subgrain boundaries. (author)

Three-dimensional grain structure of sintered bulk strontium titanate from X-ray diffraction contrast tomography

DEFF Research Database (Denmark)

Syha, M.; Rheinheimer, W.; Bäurer, M.

2012-01-01

The three-dimensional grain boundary network of sintered bulk strontium titanate is reconstructed using X-ray diffraction contrast tomography, a non-destructive technique for determining the grain shape and crystallographic orientation in polycrystals that is ideally suited for detailed studies...

Growth and characterization of magnesium chloride and lanthanum chloride doped strontium tartrate crystals - gel method

International Nuclear Information System (INIS)

Kalaiarasi, S.; Jaikumar, D.

2014-01-01

Growth of single crystals of doped strontium tartrate by controlled diffusion of strontium chloride into the silica gel charged with tartaric acid at room temperature is narrated. In this study, we synthesized magnesium chloride (5% and 10%) doped strontium tartrate crystals and Lanthanum chloride (5%, 10% and 15%) doped strontium tartrate crystals are grown. The crystal structure of the compound crystals was confirmed by single crystal X-ray diffraction. The Fourier transform infrared spectrum of pure and doped crystals are recorded and analyzed. The UV-Vis-NIR spectrum analysis reveals that the optical study of the grown crystals. The second harmonic generation efficiency was measured by using Kurtz powder technique with Nd:YAG laser of wavelength 1064 nm. (author)

Elastic wave excitation in centrosymmetric strontium titanate crystals

International Nuclear Information System (INIS)

Yushin, N.K.; Sotnikov, A.V.

1980-01-01

The main experimental dependencies are measured and the excitation mechanism of elastic waves in centrosymmetric crystals is established. The surface generation of three-dimensional elastic waves of the 30 MHz frequency in strontium titanate crystals is observed and studied. Elastic wave excitation is observed in the 4 350 K temperature range. The efficiency of hysteresis excitation depends on the external electric field. The effect of light irradiation on the amplitude of excited elastic waves is observed. It is shown that escitation is connected with linearization of electrostriction by the constant electric field appearing in a near-surface crystal layer due to phenomena in the Schottky barrier and appearance of electretic near-electrode layers

Textured strontium titanate layers on platinum by atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Blomberg, T., E-mail: tom.blomberg@asm.com [ASM Microchemistry Ltd., Vaeinoe Auerin katu 12 A, 00560 Helsinki (Finland); Anttila, J.; Haukka, S.; Tuominen, M. [ASM Microchemistry Ltd., Vaeinoe Auerin katu 12 A, 00560 Helsinki (Finland); Lukosius, M.; Wenger, Ch. [IHP, Im Technologiepark 25, 15236 Frankfurt (Oder) (Germany); Saukkonen, T. [Aalto University, Puumiehenkuja 3, 02150 Espoo (Finland)

2012-08-31

Formation of textured strontium titanate (STO) layers with large lateral grain size (0.2-1 {mu}m) and low X-ray reflectivity roughness ({approx} 1.36 nm) on Pt electrodes by industry proven atomic layer deposition (ALD) method is demonstrated. Sr(t-Bu{sub 3}Cp){sub 2}, Ti(OMe){sub 4} and O{sub 3} precursors at 250 Degree-Sign C were used to deposit Sr rich STO on Pt/Ti/SiO{sub 2}/Si Empty-Set 200 mm substrates. After crystallization post deposition annealing at 600 Degree-Sign C in air, most of the STO grains showed a preferential orientation of the {l_brace}001{r_brace} plane parallel to the substrate surface, although other orientations were also present. Cross sectional and plan view transmission electron microscopy and electron diffraction analysis revealed more than an order of magnitude larger lateral grain sizes for the STO compared to the underlying multicrystalline {l_brace}111{r_brace} oriented platinum electrode. The combination of platinum bottom electrodes with ALD STO(O{sub 3}) shows a promising path towards the formation of single oriented STO film. - Highlights: Black-Right-Pointing-Pointer Amorphous strontium titanate (STO) on platinum formed a textured film after annealing. Black-Right-Pointing-Pointer Single crystal domains in 60 nm STO film were 0.2-1 {mu}m wide. Black-Right-Pointing-Pointer Most STO grains were {l_brace}001{r_brace} oriented.

Porous allograft bone scaffolds: doping with strontium.

Directory of Open Access Journals (Sweden)

Yantao Zhao

Full Text Available Strontium (Sr can promote the process of bone formation. To improve bioactivity, porous allograft bone scaffolds (ABS were doped with Sr and the mechanical strength and bioactivity of the scaffolds were evaluated. Sr-doped ABS were prepared using the ion exchange method. The density and distribution of Sr in bone scaffolds were investigated by inductively coupled plasma optical emission spectrometry (ICP-OES, X-ray photoelectron spectroscopy (XPS, and energy-dispersive X-ray spectroscopy (EDS. Controlled release of strontium ions was measured and mechanical strength was evaluated by a compressive strength test. The bioactivity of Sr-doped ABS was investigated by a simulated body fluid (SBF assay, cytotoxicity testing, and an in vivo implantation experiment. The Sr molar concentration [Sr/(Sr+Ca] in ABS surpassed 5% and Sr was distributed nearly evenly. XPS analyses suggest that Sr combined with oxygen and carbonate radicals. Released Sr ions were detected in the immersion solution at higher concentration than calcium ions until day 30. The compressive strength of the Sr-doped ABS did not change significantly. The bioactivity of Sr-doped material, as measured by the in vitro SBF immersion method, was superior to that of the Sr-free freeze-dried bone and the Sr-doped material did not show cytotoxicity compared with Sr-free culture medium. The rate of bone mineral deposition for Sr-doped ABS was faster than that of the control at 4 weeks (3.28 ± 0.23 µm/day vs. 2.60 ± 0.20 µm/day; p<0.05. Sr can be evenly doped into porous ABS at relevant concentrations to create highly active bone substitutes.

Full Ceramic Fuel Cells Based on Strontium Titanate Anodes, An Approach Towards More Robust SOFCs

DEFF Research Database (Denmark)

Holtappels, Peter; Irvine, J.T.S.; Iwanschitz, B.

2013-01-01

The persistent problems with Ni-YSZ cermet based SOFCs, with respect to redox stability and tolerance towards sulfur has stimulated the development of a full ceramic cell based on strontium titanate(ST)- based anodes and anode support materials, within the EU FCH JU project SCOTAS-SOFC. Three...

Mechanical and Microstructural Evaluation of Barium Strontium Titanate Thin Films for Improved Antenna Performance and Reliability

National Research Council Canada - National Science Library

Hubbard, C

1999-01-01

Ferroelectric barium strontium titanate (Ba(1-x)SrxTiO3 BSTO) films of 1-micron nominal thickness were deposited on single crystals of sapphire and electroded substrates at substrate temperatures varying from 30 deg C to 700 deg C...

A FAMILY OF PEROXO-TITANATE MATERIALS TAILORED FOR OPTIMAL STRONTIUM ANDACTINIDE SORPTION

International Nuclear Information System (INIS)

Hobbs, D

2006-01-01

Achieving global optimization of inorganic sorbent efficacy, as well as tailoring sorbent specificity for target sorbates would facilitate increased wide-spread use of these materials in applications such as producing potable water or nuclear waste treatment. Sodium titanates have long been known as sorbents for radionuclides; 90 Sr and transuranic elements in particular. We have developed a related class of materials, which we refer to as peroxo-titanates: these are sodium titanates or hydrous titanates synthesized in the presence of or treated post-synthesis with hydrogen peroxide. Peroxo-titanates show remarkable and universal improved sorption behavior with respect to separation of actinides and strontium from Savannah River Site (SRS) nuclear waste simulants. Enhancement in sorption kinetics can potentially result in as much as an order of magnitude increase in batch processing throughput. Peroxo-titanates have been produced by three different synthetic routes: post-synthesis peroxide-treatment of a commercially produced monosodium titanate, an aqueous-peroxide synthetic route, and an isopropanol-peroxide synthetic route. The peroxo-titanate materials are characteristically yellow to orange, indicating the presence of protonated or hydrated Ti-peroxo species; and the chemical formula can be generally written as H v Na w Ti 2 O 5 -(xH 2 O)[yH z O 2 ] where (v+w) = 2, z = 0-2, and total volatile species accounts for 25-50 wt % of the solid. Further enhancement of sorption performance is achieved by processing, storing and utilizing the peroxo-titanate as an aqueous slurry rather than a dry powder, and post-synthesis acidification. All three synthesis modifications; addition of hydrogen peroxide, use of a slurry form and acidification can be applied more broadly to the optimization of other metal oxide sorbents and other ion separations processes

DEVELOPMENT OF PROTOTYPE TITANATE ION EXCHANGE LOADED MEMBRANES FOR STRONTIUM, CESIUM AND ACTINIDE DECONTAMINATION FROM AQUEOUS MEDIA

Energy Technology Data Exchange (ETDEWEB)

Oji, L; Keisha Martin, K; David Hobbs, D

2008-05-30

We have successfully incorporated high surface area particles of titanate ion exchange materials (monosodium titanate and crystalline silicotitanate) with acceptable particle size distribution into porous and inert support membrane fibrils consisting of polytetrafluoroethylene (Teflon{reg_sign}), polyethylene and cellulose materials. The resulting membrane sheets, under laboratory conditions, were used to evaluate the removal of surrogate radioactive materials for cesium-137 and strontium-90 from high caustic nuclear waste simulants. These membrane supports met the nominal requirement for nonchemical interaction with the embedded ion exchange materials and were porous enough to allow sufficient liquid flow. Some of this 47-mm size stamped out prototype titanium impregnated ion exchange membrane discs was found to remove more than 96% of dissolved cesium-133 and strontium-88 from a caustic nuclear waste salt simulants. Since in traditional ion exchange based column technology monosodium titanate (MST) is known to have great affinity for the sorbing of other actinides like plutonium, neptunium and even uranium, we expect that the MST-based membranes developed here, although not directly evaluated for uptake of these three actinides because of costs associated with working with actinides which do not have 'true' experimental surrogates, would also show significant affinity for these actinides in aqueous media. It was also observed that crystalline silicotitanate impregnated polytetrafluoroethylene or polyethylene membranes became less selective and sorbed both cesium and strontium from the caustic aqueous salt simulants.

An epitaxial transparent conducting perovskite oxide: double-doped SrTiO3

NARCIS (Netherlands)

Ravichandran, Jayakanth; Siemons, W.; Heijmerikx, Herman; Huijben, Mark; Majumdar, Arun; Ramesh, Ramamoorthy

2010-01-01

Epitaxial thin films of strontium titanate doped with different concentrations of lanthanum and oxygen vacancies were grown on LSAT substrates by pulsed laser deposition technique. Films grown with 5−15% La doping and a critical growth pressure of 1−10 mTorr showed high transparency (>70−95%) in the

LIGHT INTENSITY INFLUENCE ON STRONTIUM TITANATE BASED PHOTO- ELECTROCHEMICAL CELLS

Directory of Open Access Journals (Sweden)

D. Hertkorn

2017-07-01

Full Text Available The influence of light intensity on photo-electrochemical cells (PECs consisting of an n-type strontium titanate (SrTiO₃ photoanode and nickel cathode in potassium hydroxide electrolyte is studied. The band levels of an electrolyte-metal-semiconductor-electrolyte system are presented and the effect of different light intensities on the energy levels is investigated. Photocurrent density, quantum efficiency, and open circuit potential measurements are performed on the processed PECs under different light intensities (375 nm. It is demonstrated that a threshold value of the light intensity has to be reached in order to obtain positive photo activity and that beyond this value the performance remains nearly constant.

Dielectric characterization of low-loss calcium strontium titanate fibers produced by laser floating zone technique for wireless communication

International Nuclear Information System (INIS)

Amaral, F.; Valente, M.A.; Costa, L.C.; Costa, F.M.

2014-01-01

Wireless communication technology assisted to a huge development during the last two decades, responding to the growing demand for small size and low weight devices such as cell phones and global positioning systems. The need for miniaturization and higher autonomy resulted in the development of new dielectric oxide ceramics with very specific properties, to be applied as dielectric resonators in filters, oscillators, and antennas. Some crucial properties as a high quality factor, high dielectric constant, and near zero temperature coefficient of resonant frequency must be considered during the selection of the appropriate materials. The present work deals with the preparation of calcium titanate (CaTiO 3 ), strontium titanate (SrTiO 3 ), and calcium strontium titanate (Ca x Sr 1-x TiO 3 ) fibers produced by laser floating zone (LFZ) technique. Our results show that fibers grown at lower pulling rates exhibit higher ε', for all the studied frequency range, including the microwave region. Moreover, the quality factor is always high envisaging the possibility to include these materials in future wireless device applications. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Dielectric characterization of low-loss calcium strontium titanate fibers produced by laser floating zone technique for wireless communication

Energy Technology Data Exchange (ETDEWEB)

Amaral, F. [Department of Physics and I3N, University of Aveiro, 3810-193, Aveiro (Portugal); Polytechnic Institute of Coimbra, 3000-271, Coimbra (Portugal); Valente, M.A.; Costa, L.C.; Costa, F.M. [Department of Physics and I3N, University of Aveiro, 3810-193, Aveiro (Portugal)

2014-09-15

Wireless communication technology assisted to a huge development during the last two decades, responding to the growing demand for small size and low weight devices such as cell phones and global positioning systems. The need for miniaturization and higher autonomy resulted in the development of new dielectric oxide ceramics with very specific properties, to be applied as dielectric resonators in filters, oscillators, and antennas. Some crucial properties as a high quality factor, high dielectric constant, and near zero temperature coefficient of resonant frequency must be considered during the selection of the appropriate materials. The present work deals with the preparation of calcium titanate (CaTiO{sub 3}), strontium titanate (SrTiO{sub 3}), and calcium strontium titanate (Ca{sub x}Sr{sub 1-x}TiO{sub 3}) fibers produced by laser floating zone (LFZ) technique. Our results show that fibers grown at lower pulling rates exhibit higher ε', for all the studied frequency range, including the microwave region. Moreover, the quality factor is always high envisaging the possibility to include these materials in future wireless device applications. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Steps in growth of Nb-doped layered titanates with very high surface area suitable for water purification

International Nuclear Information System (INIS)

Milanović, Marija; Nikolić, Ljubica M.; Stijepović, Ivan; Kontos, Athanassios G.; Giannakopoulos, Konstantinos P.

2014-01-01

Nb-doped layered titanates, as highly efficient adsorbents, have been synthesized by hydrothermal reaction for variable duration and at 150 °C in a highly alkaline solution with NbCl 5 as the Nb source. The results have shown the formation of nanosheets already after 1 h of hydrothermal processing, but morphology and phase composition change as the reaction proceeds. The prepared layered titanates have been structurally investigated via scanning and transmission electron microscopy, X-ray diffraction, as well as Raman and Fourier transform infrared spectroscopies. The steps of layered titanate growth have been followed and an intermediate layered anatase phase is identified. Thus optimized growth of mesoporous titanate materials with 10% Nb atomic content present very high specific surface area of 345.3 m 2  g −1 , and perform as very efficient adsorbents for wastewater treatment applications. - Highlights: • Nb-doped layered titanates have been prepared by a hydrothermal procedure. • Introduction of Nb to precursor lowers the rate of layered titanate formation. • Steps in growth of Nb-doped layered titanates are considered. • Nb-doped layered titanates show high/fast MB adsorption from concentrated solution

Concurrent atomistic and continuum simulation of bi-crystal strontium titanate with tilt grain boundary.

Science.gov (United States)

Yang, Shengfeng; Chen, Youping

2015-03-08

In this paper, we present the development of a concurrent atomistic-continuum (CAC) methodology for simulation of the grain boundary (GB) structures and their interaction with other defects in ionic materials. Simulation results show that the CAC simulation allows a smooth passage of cracks through the atomistic-continuum interface without the need for additional constitutive rules or special numerical treatment; both the atomic-scale structures and the energies of the four different [001] tilt GBs in bi-crystal strontium titanate obtained by CAC compare well with those obtained by existing experiments and density function theory calculations. Although 98.4% of the degrees of freedom of the simulated atomistic system have been eliminated in a coarsely meshed finite-element region, the CAC results, including the stress-strain responses, the GB-crack interaction mechanisms and the effect of the interaction on the fracture strength, are comparable with that of all-atom molecular dynamics simulation results. In addition, CAC simulation results show that the GB-crack interaction has a significant effect on the fracture behaviour of bi-crystal strontium titanate; not only the misorientation angle but also the atomic-level details of the GB structure influence the effect of the GB on impeding crack propagation.

Quantitative Voxel-to-Voxel Comparison of TriBeam and DCT Strontium Titanate Three-Dimensional Data Sets (Postprint)

Science.gov (United States)

2015-02-09

materials such as alumina (Gonzalez et al., 2013), titanium (King et al., 2010) and aluminium (Ludwig, King et al., 2009). 2.1.2. TriBeam data collection...nickel alloys (Echlin, Lenthe et al., 2014), and geological samples (Echlin et al., 2015). The strontium titanate sample was serially sectioned in the

Small-scale dislocation plasticity in strontium titanate

Energy Technology Data Exchange (ETDEWEB)

Stukowski, Alexander; Javaid, Farhan; Durst, Karsten; Albe, Karsten [Technische Universitaet Darmstadt (Germany)

2016-07-01

Strontium titanate (STO) is an optically transparent perovskite oxide ceramic material. In contrast to other ceramics, single crystal STO plastically deforms under ambient condition, without showing a phase transition or early fracture. This remarkable ductility makes it a prime candidate for different technological applications. However, while the mechanical behavior of bulk STO has been studied extensively using uniaxial compression testing techniques, little is known about the local, small-scale behavior and the details of dislocation-based nanoplasticity in this perovskite material. In this contribution we compare results obtained from new nanoindentation experiments and corresponding large-scale molecular dynamics simulations. The evolution of the plastic zone and dislocation structures that form underneath the indenter is investigated using etch-pit methods in experiments and a novel three-dimensional defect identification technique in atomistic computer models. The latter allows tracing the evolution of the complete dislocation line network as function of indentation depth, quantifying the activity of different slip systems, and correlating this information with the recorded load-displacement curves and hardness data.

Synthesis and sorption properties of new synthesized rare-earth-doped sodium titanate

International Nuclear Information System (INIS)

Ali, I.M.

2010-01-01

A series of rare-earth-doped sodium titanates with the chemical formula R x H y Na 4-(x+y) TiO 4 ·nH 2 O (where R = Ce 3+ , Nd 3+ and Sm 3+ ) were grown employing solid-state fusion reaction technique. The physico-chemical investigations indicated that the new materials were self engineered into large particles enough to be used in sorption process and having crystalline structures containing localized Na + ions. Equilibrium studies revealed that an enhancement in sorption efficiency of sodium titanate after rare-earth doping. The neodymium-rich sodium titanate exhibited a better exchange affinity for Cs + compared to the other studied series. Data on the kinetics of cesium exchange fit well to pseudo-second order and intra-particle diffusion models. In a separate experiment, it was reported that the R-HNaTi series showed responsible sorption affinity toward Ce, Nd and Sm ions in their solution mixture with insignificant selectivity trend which reflects the high stability of titanate matrices. (author)

Processing/structure/property Relationships of Barium Strontium Titanate Thin Films for Dynamic Random Access Memory Application.

Science.gov (United States)

Peng, Cheng-Jien

The purpose of this study is to see the application feasibility of barium strontium titanate (BST) thin films on ultra large scale integration (ULSI) dynamic random access memory (DRAM) capacitors through the understanding of the relationships among processing, structure and electrical properties. Thin films of BST were deposited by multi-ion -beam reactive sputtering (MIBERS) technique and metallo -organic decomposition (MOD) method. The processing parameters such as Ba/Sr ratio, substrate temperature, annealing temperature and time, film thickness and doping concentration were correlated with the structure and electric properties of the films. Some effects of secondary low-energy oxygen ion bombardment were also examined. Microstructures of BST thin films could be classified into two types: (a) Type I structures, with multi-grains through the film thickness, for amorphous as-grown films after high temperature annealing, and (b) columnar structure (Type II) which remained even after high temperature annealing, for well-crystallized films deposited at high substrate temperatures. Type I films showed Curie-von Schweidler response, while Type II films showed Debted type behavior. Type I behavior may be attributed to the presence of a high density of disordered grain boundaries. Two types of current -voltage characteristics could be seen in non-bombarded films depending on the chemistry of the films (doped or undoped) and substrate temperature during deposition. Only the MIBERS films doped with high donor concentration and deposited at high substrate temperature showed space-charge -limited conduction (SCLC) with discrete shallow traps embedded in trap-distributed background at high electric field. All other non-bombarded films, including MOD films, showed trap-distributed SCLC behavior with a slope of {~}7.5-10 due to the presence of grain boundaries through film thickness or traps induced by unavoidable acceptor impurities in the films. Donor-doping could

Characterization of barium titanate powder doped with sodium and potassium ions by using Rietveld refining

International Nuclear Information System (INIS)

Andrade, M.C.; Assis, J.T.; Pereira, F.R.

2009-01-01

A solid-reaction synthesis of doped barium titanate was done by employing barium carbonates, sodium, potassium and titanium oxides with classic procedures. Rietveld refining of X ray diffraction data of perovskite samples with tetragonal symmetry was applying and show good agreement. Besides, the treatment performed from 600 deg C produces nanocrystals of barium titanate with average size of 33 nm. The presence of endothermic peaks related to BaTiO 3 formation at relatively low temperatures was determined by thermal analysis. A pseudo-Voigt Thompson-Cox-Hastings function was used to fit the standard samples of barium titanate. The Rietveld method has showed be efficient to detect the influences of temperature and doping on barium titanate microstructures. (author)

Scaling up aqueous processing of A-site deficient strontium titanate for SOFC anode supports

DEFF Research Database (Denmark)

Verbraeken, Maarten C.; Sudireddy, Bhaskar Reddy; Vasechko, Viacheslav

2018-01-01

All ceramic anode supported half cells of technically relevant scale were fabricated in this study, using a novel strontium titanate anode material. The use of this material would be highly advantageous in solid oxide fuel cells due to its redox tolerance and resistance to coking and sulphur...... poisoning. Successful fabrication was possible through aqueous tape casting of both anode support and electrolyte layers and subsequent lamination. Screen printing of electrolyte layers onto green anode tapes was also attempted but resulted in cracked electrolyte layers upon firing. Microstructural...

A novel solvothermal route for obtaining strontium titanate nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Marquez-Herrera, A., E-mail: alfredo.marquez@uaslp.mx [Universidad Autonoma de San Luis Potosi, Departamento de Ingenieria Mecanica Administrativa, Coordinacion Academica Region Altiplano (COARA) (Mexico); Ovando-Medina, Victor M.; Corona-Rivera, Miguel A. [Universidad Autonoma de San Luis Potosi, Departamento de Ingenieria Quimica, Coordinacion Academica Region Altiplano (COARA) (Mexico); Hernandez-Rodriguez, E.; Zapata-Torres, M. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Legaria IPN (Mexico); Campos-Gonzalez, E.; Guillen-Cervantes, A.; Zelaya-Angel, O.; Melendez-Lira, M. [CINVESTAV-IPN, Departamento de Fisica (Mexico)

2013-04-15

Strontium titanate (SrTiO{sub 3}) has attracted a lot of attention because of its possible applications in new microelectronic devices. It is a material with a high dielectric constant, low leakage current, and some of its properties can be changed by adding or modifying the concentration of a dopant, which can be used for a wide range of functional purposes, from simple capacitors to complicated microwave devices. Therefore, in this work, we report the development of a new route to synthesize SrTiO{sub 3} nanoparticles based on the solvothermal method by employing two precursor solutions: strontium chloride and titanium(IV) butoxide. Our route allows the production of cubic SrTiO{sub 3} nanoparticles with a narrow size distribution. The particle sizes range between 8 and 24 nm, forming agglomerates of SrTiO{sub 3} in the range of 128-229 nm. It was demonstrated that the Ti/Sr molar ratio employed into the precursor solution has an important effect onto the chemical composition of the resulting SrTiO{sub 3} nanoparticles: when using Ti/Sr < 1, the formation and incorporation of the SrCO{sub 3} compound into the nanoparticles was observed while with Ti/Sr {>=} 1 nanoparticles are free of contaminants. The as-prepared nanoparticles were characterized by energy-dispersive X-ray spectroscopy, X-ray diffraction, transmission electron microscopy, high-resolution TEM, selected area electron diffraction, scanning electron microscopy, and dynamic light scattering.

Electrical behaviour of strontium-doped lanthanum manganite interfaces

DEFF Research Database (Denmark)

Koch, Søren; Hendriksen, P.V.; Jacobsen, Torben

2005-01-01

The contact resistance of strontium-doped lanthanum manganite (LSM) contact pairs is investigated by polarisation analysis at different temperatures and atmospheres. The ceramic contacts have a high contact resistance, and strongly nonlinear current–voltage behaviour is observed at low temperatur....... The nonlinear behaviour is ascribed to the presence of energy barriers at the contact interface. Generally, point contacts showed a more linear behaviour than plane contact interfaces....

Direct large-scale synthesis of perovskite barium strontium titanate nano-particles from solutions

International Nuclear Information System (INIS)

Qi Jianquan; Wang Yu; Wan Pingchen; Long Tuli; Chan, Helen Lai Wah

2005-01-01

This paper reports a wet chemical synthesis technique for large-scale fabrication of perovskite barium strontium titanate nano-particles near room temperature and under ambient pressure. The process employs titanium alkoxide and alkali earth hydroxides as starting materials and involves very simple operation steps. Particle size and crystallinity of the particles are controllable by changing the processing parameters. Observations by X-ray diffraction, scanning electron microscopy and transmission electron microscopy TEM indicate that the particles are well-crystallized, chemically stoichiometric and ∼50nm in diameter. The nanoparticles can be sintered into ceramics at 1150 deg. C and show typical ferroelectric hysteresis loops

Spin injection and detection in lanthanum- and niobium-doped SrTiO3 using the Hanle technique

KAUST Repository

Han, Wei; Jiang, Xin; Kajdos, Adam; Yang, See-Hun; Stemmer, Susanne; Parkin, Stuart S. P.

2013-01-01

as the temperature is decreased to low temperatures. However, the mobility of the strontium titanate has a strong temperature dependence. This behaviour and the carrier doping dependence of the spin lifetime suggest that the spin lifetime is limited by spin

Thermoelectric power and electrical conductivity of strontium-doped lanthanum manganite

DEFF Research Database (Denmark)

Ahlgren, E.O.; Poulsen, F.W.

1996-01-01

Thermoelectric power and electrical conductivity of pure and 5, 10 and 20% strontium-doped lanthanum manganite are determined as function of temperature in air and of P-O2 at 1000 degrees C. At high temperatures the thermoelectric power is negative. Both thermoelectric power and conductivity...

Properties of barium strontium titanate at millimeter wave frequencies

Energy Technology Data Exchange (ETDEWEB)

Osman, Nurul [Department of Physics, Universiti Putra Malaysia (Malaysia); Free, Charles [Department of Engineering and Design, University of Sussex (United Kingdom)

2015-04-24

The trend towards using higher millimetre-wave frequencies for communication systems has created a need for accurate characterization of materials to be used at these frequencies. Barium Strontium Titanate (BST) is a ferroelectric material whose permittivity is known to change as a function of applied electric field and have found varieties of application in electronic and communication field. In this work, new data on the properties of BST characterize using the free space technique at frequencies between 145 GHz and 155 GHz for both thick film and bulk samples are presented. The measurement data provided useful information on effective permittivity and loss tangent for all the BST samples. Data on the material transmission, reflection properties as well as loss will also be presented. The outcome of the work shows through practical measurement, that BST has a high permittivity with moderate losses and the results also shows that BST has suitable properties to be used as RAM for high frequency application.

Strontium titanate/silicon-based terahertz photonic crystal multilayer stack

Energy Technology Data Exchange (ETDEWEB)

Xin, J.Z.; Jim, K.L.; Tsang, Y.H.; Chan, H.L.W.; Leung, C.W. [Hong Kong Polytechnic University, Department of Applied Physics and Materials Research Centre, Kowloon, Hong Kong (China); Yang, J.; Gong, X.J.; Chen, L.Q.; Gao, F. [Chinese Academy of Sciences, Institute of Biomedical and Health Engineering, Shenzhen Institutes of Advanced Technology, Shenzhen (China)

2012-04-15

A one-dimensional photonic crystal working in the terahertz (THz) range was designed and implemented. To facilitate the design, the transmission properties of strontium titanate crystals were characterized by THz-time-domain spectroscopy. Relatively high refractive index ({proportional_to}18.5) and transmission ratio (0.08) were observed between 0.2 to 1 THz. A stacked structure of (Si d{sub Si}/STO d{sub STO}){sub N} /Si d{sub Si} was then designed, with transmission spectra calculated by the transfer matrix method. The effects of the filling ratio (d{sub STO}/(d{sub Si}+d{sub STO})), periodicity (d{sub Si}+d{sub STO}) and the number of repeats N on the transmission of PC were investigated. The effect of introducing a defect layer was also studied. Based on these, Si/STO multilayers with STO defect thickness of 125 {mu}m and 200 {mu}m were measured. The shift of the defect mode was observed and compared with the calculations. (orig.)

Strontium titanate/silicon-based terahertz photonic crystal multilayer stack

International Nuclear Information System (INIS)

Xin, J.Z.; Jim, K.L.; Tsang, Y.H.; Chan, H.L.W.; Leung, C.W.; Yang, J.; Gong, X.J.; Chen, L.Q.; Gao, F.

2012-01-01

A one-dimensional photonic crystal working in the terahertz (THz) range was designed and implemented. To facilitate the design, the transmission properties of strontium titanate crystals were characterized by THz-time-domain spectroscopy. Relatively high refractive index (∝18.5) and transmission ratio (0.08) were observed between 0.2 to 1 THz. A stacked structure of (Si d Si /STO d STO ) N /Si d Si was then designed, with transmission spectra calculated by the transfer matrix method. The effects of the filling ratio (d STO /(d Si +d STO )), periodicity (d Si +d STO ) and the number of repeats N on the transmission of PC were investigated. The effect of introducing a defect layer was also studied. Based on these, Si/STO multilayers with STO defect thickness of 125 μm and 200 μm were measured. The shift of the defect mode was observed and compared with the calculations. (orig.)

Electrooptic and piezoelectric measurements in photorefractive barium titanate and strontium barium niobate

International Nuclear Information System (INIS)

Ducharme, S.; Feinberg, J.; Neurgaonkar, R.R.

1987-01-01

The authors measured the low-frequency (''unclamped'') electrooptic and piezoelectric coefficients in undoped BaTiO/sub 3/ and Sr/sub x/Ba/sub 1-x/Nb/sub 2/O/sub 6/ (chi - 0.61) crystals using interferometric techniques. The contribution of the piezoelectric effect to the Pockels measurement is discussed. For an applied ac electric field in the range 0.1-200 V/cm, the electrooptic and piezoelectric effects are linear in the magnitude of of the applied field and independent of its frequency in the range of 10 Hz-100 kHz. The unclamped electrooptic coefficients of poled BaTiO/sub 3/ single crystals are r/sub 13/ = 19.5 +- 1 pm/V and r/sub 33/ = 97 +- 7 pm/V, and for strontium barium niobate are r/sub 13/ = 47 +- 5 pm/V and r/sub 33/ = 235 +- 21 pm/V, all measured at a wavelength of 514.5 nm and at T = 23 0 C. For the barium titanate samples the measured Pockels coefficient r/sub c/ identical to r/sub 33/ - (n/sub 1//n/sub 3/)/sup 3/r/sub 13/ = 79 +- 6 pm/V in good agreement with the value r/sub c/ = 76 +- 7 pm/V computed from the above values of r/sub 13/ and r/sub 33/, where n/sub 1/ and n/sub 3/ are the ordinary and extraordinary indexes of refraction, respectively. The measured piezoelectric coefficient is d/sub 23/ = +28.7 +- 2 pm/V for barium titanate, and is d/sub 23/ = +24.6 +- 2 pm/V for strontium barium niobate. They also measured the photoreflective coupling of two optical beams in the crystals, and they show that the dependence of the coupling strength on beam polarization is in fair agreement with the measured values of the Pockels coefficients

Deposition barium titanate (BaTiO3) doped lanthanum with chemical solution deposition

International Nuclear Information System (INIS)

Iriani, Y.; Nurhadi, N.; Jamaludin, A.

2016-01-01

Deposition of Barium Titanate (BaTiO 3 ) thin films used Chemical Solution Deposition (CSD) method and prepared with spin coater. BaTiO 3 is doped with lanthanum, 1%, 2%, and 3%. The thermal process use annealing temperature 900°C and holding time for 3 hours. The result of characterization with x-ray diffraction (XRD) equipment show that the addition of La 3+ doped on Barium Titanate caused the change of angle diffraction.The result of refine with GSAS software shows that lanthanum have been included in the structure of BaTiO 3 . Increasing mol dopant La 3+ cause lattice parameter and crystal volume become smaller. Characterization result using Scanning Electron Microscopy (SEM) equipment show that grain size (grain size) become smaller with increasing mole dopant (x) La 3+ . The result of characterization using Sawyer Tower methods show that all the samples (Barium Titanante and Barium Titanate doped lanthanum) are ferroelectric material. Increasing of mole dopant La 3+ cause smaller coercive field and remanent polarization increases. (paper)

Effects of surrounding powder in sintering process on the properties of Sb and Mn- doped barium-strontium titanate PTCR ceramics

Directory of Open Access Journals (Sweden)

Pornsuda Bomlai

2006-05-01

Full Text Available In this research, the effects of surrounding powder used during sintering of Sb and Mn doped bariumstrontium titanate (BST ceramics were studied. The ceramic samples were prepared by a conventional mixed-oxide method and placed on different powders during sintering. Phase formation, microstructure and PTCR behavior of the samples were then observed. Microstructures and PTCR behavior varied with the type of surrounding powder, whereas the crystal structure did not change. The surrounding powder has more effects on the shape of the grain than on the size. The grain size of samples was in the range of 5-20 μm. The most uniform grain size and the highest increase of the ratio of ρmax/ρRT were found to be about 106 for samples which had been sintered on Sb-doped BST powder. This value was an order of magnitude greater than for samples sintered on a powder of the equivalent composition to that of the sample pellet.

Udvikling af materialer til brintpermeable membraner

DEFF Research Database (Denmark)

Bentzer, Henrik Karnøe

doped samarium titanate, lanthanum magnesium titanate and strontium cerate doped with yttrium and nickel. Concentration cell measurements were used to estimate transport numbers for protons and oxide ions in yttrium doped strontium cerate and calcium doped samarium titanate. Furthermore, the voltage......Due to global warming as well as other factors, it is necessary to find alternatives to the current consumption of fossil fuels. Oxide materials with high protonic conductivity can potentially find application within many different technological fields in a society that is based on renewable energy...

Syntheses, Structures, and Magnetic Properties of Nickel-Doped Lepidocrocite Titanates

DEFF Research Database (Denmark)

Gao, Tao; Norby, Poul; Okamoto, Hiroshi

2009-01-01

Ni-doped titanate CsxTi2−x/2Nix/2O4 and its protonic derivative HxTi2−x/2Nix/2O4·xH2O (x = 0.7) were synthesized and characterized by means of synchrotron X-ray diffraction, Raman scattering, X-ray photoelectron spectroscopy (XPS), and magnetic measurements. CsxTi2−x/2Nix/2O4 crystallizes......H2O. Ni- and Mg-codoped titanates CsxTi2−x/2(NiyMg1−y)x/2O4 (x = 0.7, 0 ≤ y ≤ 1) were also reported. The crystal structure, interlayer chemistry, and magnetic properties of the titanates depend on the Ni substitution levels, indicating opportunities for tuning of the properties by controlling...

Analysis of isothermal sintering of zinc-titanate doped with MgO

Directory of Open Access Journals (Sweden)

Obradović N.

2007-01-01

Full Text Available The aim of this work was analysis of isothermal sintering of zinc titanate ceramics doped with MgO obtained by mechanical activation. Mixtures of ZnO, TiO2 and MgO (0, 1.25 and 2.5% were mechanically activated 15 minutes in a planetary ball mill. The powders obtained were pressed under different pressures and the results were fitted with a phenomenological compacting equation. Isothermal sintering was performed in air for 120 minutes at four different temperatures. Structural characterization of ZnO-TiO2-MgO system after milling was performed at room temperature using XRPD measurements. DTA measurements showed different activation energies for pure and doped ZnO-TiO2 systems. Thus addition of MgO stabilizes the crystal structure of zinc titanate.

Comparative study of broadband electrodynamic properties of single-crystal and thin-film strontium titanate

International Nuclear Information System (INIS)

Findikoglu, A. T.; Jia, Q. X.; Kwon, C.; Reagor, D. W.; Kaduchak, G.; Rasmussen, K. Oe.; Bishop, A. R.

1999-01-01

We have used a coplanar waveguide structure to study broadband electrodynamic properties of single-crystal and thin-film strontium titanate. We have incorporated both time- and frequency-domain measurements to determine small-signal effective refractive index and loss tangent as functions of frequency (up to 4 GHz), dc bias (up to 10 6 V/m), and cryogenic temperature (17 and 60 K). The large-signal impulse response of the devices and the associated phenomenological nonlinear wave equation illustrate how dissipation and nonlinearity combine to produce the overall response in the large-signal regime. (c) 1999 American Institute of Physics

Visible light carrier generation in co-doped epitaxial titanate films

Energy Technology Data Exchange (ETDEWEB)

Comes, Ryan B., E-mail: ryan.comes@pnnl.gov; Kaspar, Tiffany C.; Chambers, Scott A. [Fundamental and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Smolin, Sergey Y.; Baxter, Jason B. [Department of Chemical and Biological Engineering, Drexel University, Philadelphia, Pennsylvania 19104 (United States); Gao, Ran [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Apgar, Brent A. [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, Champaign, Illinois 61801 (United States); Martin, Lane W. [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Materials Science Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Bowden, Mark E. [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States)

2015-03-02

Perovskite titanates such as SrTiO{sub 3} (STO) exhibit a wide range of important functional properties, including ferroelectricity and excellent photocatalytic performance. The wide optical band gap of titanates limits their use in these applications; however, making them ill-suited for integration into solar energy harvesting technologies. Our recent work has shown that by doping STO with equal concentrations of La and Cr, we can enhance visible light absorption in epitaxial thin films while avoiding any compensating defects. In this work, we explore the optical properties of photoexcited carriers in these films. Using spectroscopic ellipsometry, we show that the Cr{sup 3+} dopants, which produce electronic states immediately above the top of the O 2p valence band in STO reduce the direct band gap of the material from 3.75 eV to 2.4–2.7 eV depending on doping levels. Transient reflectance spectroscopy measurements are in agreement with the observations from ellipsometry and confirm that optically generated carriers are present for longer than 2 ns. Finally, through photoelectrochemical methylene blue degradation measurements, we show that these co-doped films exhibit enhanced visible light photocatalysis when compared to pure STO.

Synthesis and properties of Co-doped titanate nanotubes and their optical sensitization with methylene blue

International Nuclear Information System (INIS)

Ferreira, V.C.; Nunes, M.R.; Silvestre, A.J.; Monteiro, O.C.

2013-01-01

Here we report on a novel chemical route to synthesize homogenous cobalt-doped titanate nanotubes (CoTNT), using an amorphous Co-doped precursor. The influence of the synthesis temperature, autoclave dwell time and metal doping on the structural and microstructural as well as on the optical properties of the synthesized titanate nanotubes is studied and discussed. The optical band gaps of the CoTNT samples are red shifted in comparison with the values determined for the undoped samples, such red shifts bringing the absorption edge of the CoTNT samples into the visible region. CoTNT materials also demonstrate particular high adsorption ability for methylene blue, the amount of the adsorbed dye being higher than the one predictable for a monolayer formation. This suggests the possibility of intercalation of the dye molecule between the TiO 6 layers of the TNT structure. It is also shown that the methylene blue sensitized Co-doped nanostructures are highly stable under UV radiation and present a strong and broad absorption in the visible region. - Highlights: • New hydrothermal chemical route to synthesize cobalt-doped titanate nanotubes. • The Co-doping stabilizes the TNTs morphology in a temperature range of 160–200 °C. • Optical band gaps of CoTNTs are red shifted compared to the TNT samples. • Methylene blue sensitized CoTNTs are highly stable under UV–vis irradiation

Synthesis and properties of Co-doped titanate nanotubes and their optical sensitization with methylene blue

Energy Technology Data Exchange (ETDEWEB)

Ferreira, V.C. [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CQB, Campo Grande, 1749-016 Lisboa (Portugal); Nunes, M.R. [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CCMM, Campo Grande, 1749-016 Lisboa (Portugal); Silvestre, A.J. [Instituto Superior de Engenharia de Lisboa, Department of Physics and ICEMS, R. Conselheiro Emídio Navarro 1, 1959-007 Lisboa (Portugal); Monteiro, O.C., E-mail: ocmonteiro@fc.ul.pt [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CQB, Campo Grande, 1749-016 Lisboa (Portugal)

2013-10-01

Here we report on a novel chemical route to synthesize homogenous cobalt-doped titanate nanotubes (CoTNT), using an amorphous Co-doped precursor. The influence of the synthesis temperature, autoclave dwell time and metal doping on the structural and microstructural as well as on the optical properties of the synthesized titanate nanotubes is studied and discussed. The optical band gaps of the CoTNT samples are red shifted in comparison with the values determined for the undoped samples, such red shifts bringing the absorption edge of the CoTNT samples into the visible region. CoTNT materials also demonstrate particular high adsorption ability for methylene blue, the amount of the adsorbed dye being higher than the one predictable for a monolayer formation. This suggests the possibility of intercalation of the dye molecule between the TiO{sub 6} layers of the TNT structure. It is also shown that the methylene blue sensitized Co-doped nanostructures are highly stable under UV radiation and present a strong and broad absorption in the visible region. - Highlights: • New hydrothermal chemical route to synthesize cobalt-doped titanate nanotubes. • The Co-doping stabilizes the TNTs morphology in a temperature range of 160–200 °C. • Optical band gaps of CoTNTs are red shifted compared to the TNT samples. • Methylene blue sensitized CoTNTs are highly stable under UV–vis irradiation.

Persistent optically induced magnetism in oxygen-deficient strontium titanate.

Science.gov (United States)

Rice, W D; Ambwani, P; Bombeck, M; Thompson, J D; Haugstad, G; Leighton, C; Crooker, S A

2014-05-01

Strontium titanate (SrTiO3) is a foundational material in the emerging field of complex oxide electronics. Although its bulk electronic and optical properties are rich and have been studied for decades, SrTiO3 has recently become a renewed focus of materials research catalysed in part by the discovery of superconductivity and magnetism at interfaces between SrTiO3 and other non-magnetic oxides. Here we illustrate a new aspect to the phenomenology of magnetism in SrTiO3 by reporting the observation of an optically induced and persistent magnetization in slightly oxygen-deficient bulk SrTiO3-δ crystals using magnetic circular dichroism (MCD) spectroscopy and SQUID magnetometry. This zero-field magnetization appears below ~18 K, persists for hours below 10 K, and is tunable by means of the polarization and wavelength of sub-bandgap (400-500 nm) light. These effects occur only in crystals containing oxygen vacancies, revealing a detailed interplay between magnetism, lattice defects, and light in an archetypal complex oxide material.

Review on dielectric properties of rare earth doped barium titanate

International Nuclear Information System (INIS)

Ismail, Fatin Adila; Osman, Rozana Aina Maulat; Idris, Mohd Sobri

2016-01-01

Rare earth doped Barium Titanate (BaTiO_3) were studied due to high permittivity, excellent electrical properties and have wide usage in various applications. This paper reviewed on the electrical properties of RE doped BaTiO_3 (RE: Lanthanum (La), Erbium (Er), Samarium (Sm), Neodymium (Nd), Cerium (Ce)), processing method, phase transition occurred and solid solution range for complete study. Most of the RE doped BaTiO_3 downshifted the Curie temperature (T_C). Transition temperature also known as Curie temperature, T_C where the ceramics had a transition from ferroelectric to a paraelectric phase. In this review, the dielectric constant of La-doped BaTiO_3, Er-doped BaTiO_3, Sm-doped BaTiO_3, Nd-doped BaTiO_3 and Ce-doped BaTiO_3 had been proved to increase and the transition temperature or also known as T_C also lowered down to room temperature as for all the RE doped BaTiO_3 except for Er-doped BaTiO_3.

Dielectric properties of calicum and barium-doped strontium titanate

Science.gov (United States)

Tung, Li-Chun

Dielectric properties of high quality polycrystalline Ca- and Ba-doped SrTiO3 perovskites are studied by means of dielectric constant, dielectric loss and ferroelectric hysteresis measurements. Low frequency dispersion of the dielectric constant is found to be very small and a simple relaxor model may not be able to explain its dielectric behavior. Relaxation modes are found in these samples, and they are all interpreted as thermally activated Bipolar re-orientation across energy barriers. In Sr1- xCaxTiO3 (x = 0--0.3), two modes are found associated with different relaxation processes, and the concentration dependence implies a competition between these processes. In Sr1-xBa xTiO3 (x = 0--0.25), relaxation modes are found to be related to the structural transitions, and the relaxation modes persist at low doping levels (x Barret formula is discussed and two of the well-accepted models, anharmonic oscillator model and transverse Ising model, are found to be equivalent. Both of the Ca and Ba systems can be understood qualitatively within the concept of transverse Ising model.

Visible light carrier generation in co-doped epitaxial titanate films

Energy Technology Data Exchange (ETDEWEB)

Comes, Ryan B.; Smolin, Sergey Y.; Kaspar, Tiffany C.; Gao, Ran; Apgar, Brent A.; Martin, Lane W.; Bowden, Mark E.; Baxter, Jason; Chambers, Scott A.

2015-03-02

Perovskite titanates such as SrTiO3 (STO) exhibit a wide range of important functional properties, including high electron mobility, ferroelectricity—which may be valuable in photovoltaic applications—and excellent photocatalytic performance. The wide optical band gap of titanates limits their use in these applications, however, making them ill-suited for integration into solar energy harvesting technologies. Our recent work has shown that by doping STO with equal concentrations of La and Cr we can enhance visible light absorption in epitaxial thin films while avoiding any compensating defects. In this work, we explore the optical properties of photoexcited carriers in these films. Using spectroscopic ellipsometry, we show that the Cr3+ dopants, which produce electronic states immediately above the top of the O 2p valence band in STO reduce the direct band gap of the material from 3.75 eV to between 2.4 and 2.7 eV depending on doping levels. Transient reflectance measurements confirm that optically generated carriers have a recombination lifetime comparable to that of STO and are in agreement with the observations from ellipsometry. Finally, through photoelectrochemical yield measurements, we show that these co-doped films exhibit enhanced visible light photocatalysis when compared to pure STO.

Development of a metrology method for composition and thickness of barium strontium titanate thin films

International Nuclear Information System (INIS)

Remmel, Thomas; Werho, Dennis; Liu, Ran; Chu, Peir

1998-01-01

Thin films of barium strontium titanate (BST) are being investigated as the charge storage dielectric in advanced memory devices, due to their promise for high dielectric constant. Since the capacitance of BST films is a function of both stoichiometry and thickness, implementation into manufacturing requires precise metrology methods to monitor both of these properties. This is no small challenge, considering the BST film thicknesses are 60 nm or less. A metrology method was developed based on X-ray Fluorescence and applied to the measurement of stoichiometry and thickness of BST thin films in a variety of applications

Use of titanates in decontamination of defense waste

International Nuclear Information System (INIS)

Dosch, R.G.

1978-06-01

Sodium titanate, an inorganic ion exchange material, has been evaluated for use in a process to remove strontium from Defense Waste or other high-sodium, caustic solutions. Distribution coefficients on the order of 10 5 were observed at sub part per million concentrations of Sr, and the effects of other cation impurities and complexants in the waste were investigated. The preparation and general chemical properties of the exchange material are discussed. This information was used in developing a commercial source which has since supplied a 200 kg batch of the material for evaluation. In column ion exchange experiments with 85 Sr-doped simulated waste, decontamination factors of 500 or greater were observed in the first 2000 to 3500 bed volumes of effluent, depending on the impurities in the simulant. A -40 to +130 mesh range of sodium titanate powder was used as the baseline material, but a study to produce alternate forms of the titanate was carried in parallel. This has resulted in two materials which appear promising with respect to both simplification of handling and chemical properties. One of the materials is an agglomerated form of the titanate formed by extrusion pelletizing using water as a binder, and the second is a macroreticular organic anion resin which was loaded with 30 to 40% (by weight) of sodium titanate. The results of initial testing of these materials are discussed

Effect of nitrogen doping on the microstructure and visible light photocatalysis of titanate nanotubes by a facile cohydrothermal synthesis via urea treatment

International Nuclear Information System (INIS)

Hu, Cheng-Ching; Hsu, Tzu-Chien; Lu, Shan-Yu

2013-01-01

A facile one-step cohydrothermal synthesis via urea treatment has been adopted to prepare a series of nitrogen-doped titanate nanotubes with highly efficient visible light photocatalysis of rhodamine B, in an effect to identify the effect of nitrogen doping on the photodegradation efficiency. The morphology and microstructure of the thus-prepared N-doped titanates were characterized by nitrogen adsorption/desorption isotherms, transmission electron microscopy, and scanning electron microscopy. With increasing urea loadings, the N-doped titanates change from a porous multi-layer and nanotube-shaped to a dense and aggregated particle-shaped structure, accompanied with reduced specific surface area and pore volume and enhanced pore diameter. Interstitial linkage to titanate via Ti-O-N and Ti-N-O is confirmed by X-ray photoelectron spectroscopy. Factors governing the photocatalytic degradation such as the specific surface area of the catalyst and the degradation pathway are analyzed, a mechanistic illustration on the photodegradation is provided, and a 3-stage degradation mechanism is identified. The synergistic contribution due to the enhanced deethylation and chromophore cleavage on rhodamine B molecules and the reduced band gap on the catalyst TiO 2 by interstitial nitrogen-doping has been accounted for the high photodegradation efficiency of the N-doped titanate nanotubes.

Structure, Raman, dielectric behavior and electrical conduction mechanism of strontium titanate

Science.gov (United States)

Trabelsi, H.; Bejar, M.; Dhahri, E.; Graça, M. P. F.; Valente, M. A.; Khirouni, K.

2018-05-01

Strontium titanate was prepared by solid-state reaction method. According to the XRD, it was single phase and has a cubic perovskite structure. The Raman spectroscopic investigation was carried out at room-temperature, and the second-order Raman modes were observed. By employing impedance spectroscopy, the dielectric relaxation and electrical properties were investigated over the temperature range of 500-700 K at various frequencies. The activation energies evaluated from dielectric and modulus studies are in good agreement and these values are attributed to the bulk relaxation. The impedance data were well fitted to an (R1//C1)-(R2//CPE1) equivalent electrical circuit. It could be concluded that the grain boundaries are more resistive and capacitive than the grains. The ac conductivity was found to follow the Jonscher's universal dynamic law ωS and the correlated barrier hopping model (CBH) has been proposed to describe the conduction mechanism.

Comparison study of biomimetic strontium-doped calcium phosphate coatings by electrochemical deposition and air plasma spray: morphology, composition and bioactive performance.

Science.gov (United States)

Li, Ling; Lu, Xia; Meng, Yizhi; Weyant, Christopher M

2012-10-01

In this study, strontium-doped calcium phosphate coatings were deposited by electrochemical deposition and plasma spray under different process parameters to achieve various coating morphologies. The coating composition was investigated by energy dispersive X-ray spectroscopy and X-ray diffraction. The surface morphologies of the coatings were studied through scanning electron microscopy while the cytocompatibility and bioactivity of the strontium-doped calcium phosphate coatings were evaluated using bone cell culture using MC3T3-E1 osteoblast-like cells. The addition of strontium leads to enhanced proliferation suggesting the possible benefits of strontium incorporation in calcium phosphate coatings. The morphology and composition of deposited coatings showed a strong influence on the growth of cells.

Study of a Flexible Low Profile Tunable Dipole Antenna Using Barium Strontium Titanate Varactors

Science.gov (United States)

Cure, David; Weller, Thomas; Miranda, Felix A.

2014-01-01

In this paper a flexible low profile dipole antenna using a frequency selective surface (FSS) with interdigital barium strontium titanate (BST) varactor-tuned unit cells is presented. The varactor chips were placed only along one dimension of the FSS to avoid the use of vias and simplify the DC bias network. The antenna uses overlapping metallic plates that resemble fish scales as a ground plane to improve the flexibility of the multi-material stack structure. The measured data of the antenna demonstrate tunability from 2.42 GHz to 2.66 GHz and 1.3 dB gain drop when using overlapping metallic plates instead of continuous ground plane. The total antenna thickness is approximately lambda/24.

Strontium-doped organic-inorganic hybrids towards three-dimensional scaffolds for osteogenic cells

Energy Technology Data Exchange (ETDEWEB)

John, Łukasz, E-mail: lukasz.john@chem.uni.wroc.pl [Faculty of Chemistry, University of Wrocław, 14 F. Joliot-Curie, 50-383 Wrocław (Poland); Podgórska, Marta [Faculty of Chemistry, University of Wrocław, 14 F. Joliot-Curie, 50-383 Wrocław (Poland); Nedelec, Jean-Marie [Université Clermont Auvergne, SIGMA Clermont, Institut de Chimie de Clermont-Ferrand, BP 10448, F-63000 Clermont-Ferrand (France); CNRS, UMR 6296, ICCF, F-63178 Aubiere (France); Cwynar-Zając, Łucja [Department of Histology and Embryology, Wrocław Medical University, 6a Chałubińskiego, 50-368 Wrocław (Poland); Dzięgiel, Piotr [Department of Histology and Embryology, Wrocław Medical University, 6a Chałubińskiego, 50-368 Wrocław (Poland); Department of Physiotherapy and Occupational Therapy in Conservative and Interventional Medicine, 35 Paderewskiego, 51-612 Wrocław (Poland)

2016-11-01

Biomimetic organic–inorganic hybrid bioscaffolds are developed to complement or replace damaged fragments in bone tissue surgery. The aim of this work was to develop a simple and fast method to prepare composite material for bone engineering, avoiding time consuming and complex methodologies. The resulting materials (also called in this work as hybrid composites or hybrid scaffolds) have a three-dimensional macroporous polymer-like network derived from triethoxyvinylsilane (TEVS) and 2-hydroxyethylmethacrylate (HEMA) monomers, with incorporated calcium, strontium, and phosphate ions. The materials were fully characterized using FT-IR, biomineralization studies, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy, scratch tests, Young's modulus and compressive strength tests, and gas physisorption. We report a comprehensive study on the in vitro effect of novel strontium doped materials on human bone cells. In vitro investigations were conducted using a normal human osteoblast cell line that mimics the cellular events of the in vivo intramembranous bone formation process. The materials do not have a negative impact on the survival of the normal human osteoblasts; moreover, materials doped with strontium show that not only are cells able to survive, but they also attach to and grow on a bioscaffolds surface. For this reason, they may be used in future in vivo experiments. - Highlights: • New hybrid scaffolds derived from TEVS and HEMA doped with Ca{sup 2+}, Sr{sup 2+}, and PO{sub 4}{sup 3-} ions have been developed. • A comprehensive characterization of the scaffolds for regenerative medicine was performed. • The incorporation of Sr{sup 2+} ions into the scaffolds was non-cytotoxic to the osteoblasts.

Defect and electrical transport properties of Nb-doped SrTiO₃

DEFF Research Database (Denmark)

Blennow Tullmar, Peter; Hagen, Anke; Kammer Hansen, Kent

2008-01-01

analyzed with SEM, XRD, TGA, and XANES. The electrical conductivity of Nb-doped strontium titanate (Sr0.94Ti0.9Nb0.1O3 - sintered in 9% H-2/N-2 at 1400 degrees C for 12 h) decreased with increasing temperature and showed a phonon scattering conduction mechanism with (sigma>120 S/cm at 1000 degrees C (in 9...

Strontium-doped calcium silicate bioceramic with enhanced in vitro osteogenic properties.

Science.gov (United States)

No, Young Jung; Roohaniesfahani, Seyediman; Lu, Zufu; Shi, Jeffrey; Zreiqat, Hala

2017-06-05

Gehlenite (GLN, Ca 2 SiAl 2 O 7 ) is a bioceramic that has been recently shown to possess excellent mechanical strength and in vitro osteogenic properties for bone regeneration. Substitutional incorporation of strontium in place of calcium is an effective way to further enhance biological properties of calcium-based bioceramics and glasses. However, such strategy has the potential to affect other important physicochemical parameters such as strength and degradation due to differences in the ionic radius of strontium and calcium. This study is the first to investigate the effect of a range of concentrations of strontium substitution of calcium at 1, 2, 5, 10 mol% (S1-GLN, S2-GLN, S5-GLN and S10-GLN) on the physicochemical and biological properties of GLN. We showed that up to 2 mol% strontium ion substitution retains the monophasic GLN structure when sintered at 1450 °C, whereas higher concentrations resulted in presence of calcium silicate impurities. Increased strontium incorporation resulted in changes in grain morphology and reduced densification when the ceramics were sintered at 1450 °C. Porous GLN, S1-GLN and S2-GLN scaffolds (∼80% porosity) showed compressive strengths of 2.05 ± 0.46 MPa, 1.76 ± 0.79 MPa and 1.57 ± 0.52 MPa respectively. S1-GLN and S2-GLN immersed in simulated body fluid showed increased strontium ion release but reduced calcium and silicon ion release compared to GLN without affecting overall weight loss and pH over a 21 d period. The bioactivity of the S2-GLN ceramics was significantly improved as reflected in the significant upregulation of HOB proliferation and differentiation compared to GLN. Overall, these results suggest that increased incorporation of strontium presents a trade-off between bioactivity and mechanical strength for GLN bioceramics. This is an important consideration in the development of strontium-doped bioceramics.

an oxalate-peroxide complex used in the preparation of doped barium titanate

NARCIS (Netherlands)

van der Gijp, S.; Winnubst, Aloysius J.A.; Verweij, H.

1998-01-01

A method is described for the preparation of homogeneously doped barium titanate, which can be applied in non-linear dielectric elements. Ba and Ti salts are dissolved, mixed with hydrogen peroxide and added to a solution of ammonium oxalate, resulting in the formation of an insoluble peroxo-oxalate

Antimony doped barium strontium ferrite perovskites as novel cathodes for intermediate-temperature solid oxide fuel cells

Energy Technology Data Exchange (ETDEWEB)

Ling, Yihan, E-mail: lyhyy@mail.ustc.edu.cn [School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou, 221116 (China); Lu, Xiaoyong [China Anhui Key Laboratory of Low Temperature Co-fired Materials, Department of Chemistry, Huainan Normal University, Huainan, Anhui, 232001 (China); Niu, Jinan; Chen, Hui [School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou, 221116 (China); Ding, Yanzhi [China Anhui Key Laboratory of Low Temperature Co-fired Materials, Department of Chemistry, Huainan Normal University, Huainan, Anhui, 232001 (China); Ou, Xuemei [School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou, 221116 (China); Zhao, Ling [Department of Material Science and Chemistry, China University of Geosciences, Wuhan, 430074 (China)

2016-05-05

Antimony was doped to barium strontium ferrite to produce ferrite-based perovskites with a composition of Ba{sub 0.5}Sr{sub 0.5}Fe{sub 1−x}Sb{sub x}O{sub 3−δ} (x = 0.0, 0.05, 0.1) as novel cathode materials for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The perovskite properties including oxygen nonstoichiometry (δ), mean valence of B-site, tolerance factors, thermal expansion coefficient (TEC) and electrical conductivity (σ) are explored as a function of antimony content. By defect chemistry analysis, the TECs decrease since the variable oxygen vacancy concentration is decreased by Sb doping, and σ decreases with x due to the reduced charge concentration of Fe{sup 4+} content. Consequently, the electrochemical performance was substantially improved and the interfacial polarization resistance was reduced from 0.213 to 0.120 Ωcm{sup 2} at 700 °C with Sb doping. The perovskite with x = 1.0 is suggested as the most promising composition as SOFC cathode material. - Highlights: • Antimony is doped to barium strontium ferrite to produce novel cathodes. • δ, TECs and σ are evaluated as a function of antimony content. • The electrochemical performance is substantially improved with antimony doping.

Dielectric loss of strontium titanate thin films

Science.gov (United States)

Dalberth, Mark Joseph

1999-12-01

Interest in strontium titanate (STO) thin films for microwave device applications continues to grow, fueled by the telecommunications industry's interest in phase shifters and tunable filters. The optimization of these devices depends upon increasing the phase or frequency tuning and decreasing the losses in the films. Currently, the dielectric response of thin film STO is poorly understood through lack of data and a theory to describe it. We have studied the growth of STO using pulsed laser deposition and single crystal substrates like lanthanum aluminate and neodymium gallate. We have researched ways to use ring resonators to accurately measure the dielectric response as a function of temperature, electric field, and frequency from low radio frequencies to a few gigahertz. Our films grown on lanthanum aluminate show marked frequency dispersion in the real part of the dielectric constant and hints of thermally activated loss behavior. We also found that films grown with conditions that optimized the dielectric constant showed increased losses. In an attempt to simplify the system, we developed a technique called epitaxial lift off, which has allowed us to study films removed from their growth substrates. These free standing films have low losses and show obvious thermally activated behavior. The "amount of tuning," as measured by a figure of merit, KE, is greater in these films than in the films still attached to their growth substrates. We have developed a theory that describes the real and imaginary parts of the dielectric constant. The theory models the real part using a mean field description of the ionic motion in the crystal and includes the loss by incorporating the motion of charged defects in the films.

Superconductivity in doped semiconductors

Energy Technology Data Exchange (ETDEWEB)

Bustarret, E., E-mail: Etienne.bustarret@neel.cnrs.fr

2015-07-15

A historical survey of the main normal and superconducting state properties of several semiconductors doped into superconductivity is proposed. This class of materials includes selenides, tellurides, oxides and column-IV semiconductors. Most of the experimental data point to a weak coupling pairing mechanism, probably phonon-mediated in the case of diamond, but probably not in the case of strontium titanate, these being the most intensively studied materials over the last decade. Despite promising theoretical predictions based on a conventional mechanism, the occurrence of critical temperatures significantly higher than 10 K has not been yet verified. However, the class provides an enticing playground for testing theories and devices alike.

Sensitization of Perovskite Strontium Stannate SrSnO3 towards Visible-Light Absorption by Doping

Directory of Open Access Journals (Sweden)

Hungru Chen

2014-01-01

Full Text Available Perovskite strontium stannate SrSnO3 is a promising photocatalyst. However, its band gap is too large for efficient solar energy conversion. In order to sensitize SrSnO3 toward visible-light activities, the effects of doping with various selected cations and anions are investigated by using hybrid density functional calculations. Results show that doping can result in dopant level to conduction band transitions which lie lower in energy compared to the original band gap transition. Therefore, it is expected that doping SrSnO3 can induce visible-light absorption.

Defect controlled room temperature ferromagnetism in Co-doped barium titanate nanocrystals

International Nuclear Information System (INIS)

Ray, Sugata; Kolen'ko, Yury V; Watanabe, Tomoaki; Yoshimura, Masahiro; Itoh, Mitsuru; Kovnir, Kirill A; Lebedev, Oleg I; Turner, Stuart; Erni, Rolf; Tendeloo, Gustaaf Van; Chakraborty, Tanushree

2012-01-01

Defect mediated high temperature ferromagnetism in oxide nanocrystallites is the central feature of this work. Here, we report the development of room temperature ferromagnetism in nanosized Co-doped barium titanate particles with a size of around 14 nm, synthesized by a solvothermal drying method. A combination of x-ray diffraction with state-of-the-art electron microscopy techniques confirms the intrinsic doping of Co into BaTiO 3 . The development of the room temperature ferromagnetism was tracked down to the different donor defects, namely hydroxyl groups at the oxygen site and oxygen vacancies and their relative concentrations at the surface and the core of the nanocrystal, which could be controlled by post-synthesis drying and thermal treatments.

Fabrication and Properties of Silica Gel/Calcium Sulfate/Strontium-doped β-tricalcium Phosphate Composite Porous Scaffolds for Bone Tissue Engineering

Directory of Open Access Journals (Sweden)

QIN Xiao-su

2018-03-01

Full Text Available The calcium sulfate/strontium-doped β-tricalcium phosphate composite spherical pellets was fabricated, using the calcium sulfate/strontium-doped β-TCP as raw material, and through the stirring spray drying method, and then composite spherical pellets were combined with silica gel, porous silica gel/calcium sulfate/strontium-doped β-tricalcium phosphate scaffold was obtained by stacking aggregation method in the mould. The XRD, SEM and FT-IR, etc are employed to examine the chemical composition, composite morphology and structure characteristics, and the degradability, porosity, mechanical properties and cytotoxicity of the scaffolds materials were studied. The results reveal that the composite porous scaffolds have irregular pore structure with pore size between 0.2-1.0mm, and they have a large number of micropores on each of the composite spherical pellets, with the aperture between 50-200μm. Moreover, the porosity of the composite scaffolds is about 62%, which can meet the requirements of scaffolds for bone tissue engineering in porosity; the cytotoxicity tests show the composite scaffolds have no cytotoxic effect and it has good degradation. Therefore, it has good application prospect in bone tissue engineering of the bone defect repair of non-bearing site.

Strontium doped injectable bone cement for potential drug delivery applications.

Science.gov (United States)

Taha, Ali; Akram, Muhammad; Jawad, Zaidoon; Alshemary, Ammar Z; Hussain, Rafaqat

2017-11-01

Microwave assisted wet precipitation method was used to synthesize calcium deficient strontium doped β-tricalcium phosphate (Sr-βTCP) with a chemical formula of Ca 2.96-x Sr x (PO 4 ) 2 . Sr-βTCP was reacted with monocalcium phosphate monohydrate [Ca(H 2 PO 4 ) 2 .H 2 O, MCPM] in presence of water to furnish corresponding Sr containing brushite cement (Sr-Brc). The samples were characterized by using X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and field emission scanning electron microscopy (FESEM). Strontium content in the prepared samples was determined by using inductively coupled plasma optical emission spectrometry (ICP-OES). The effect of Sr 2+ ions on the structural, mechanical, setting properties and drug release of the cement is reported. Incorporation of Sr 2+ ions improved the injectability, setting time and mechanical properties of the Brc. The release profiles of antibiotics incorporated in Brc and Sr-Brc confirmed that the Sr incorporation into the Brc results in the efficient release of the antibiotics from the cement. Copyright © 2017 Elsevier B.V. All rights reserved.

Europium-doped calcium titanate: Optical and structural evaluations

Energy Technology Data Exchange (ETDEWEB)

Mazzo, Tatiana Martelli; Pinatti, Ivo Mateus [INCTMN, LIEC, Departamento de Química, Universidade Federal de São Carlos, P.O. Box 676, 13565-905 São Carlos, SP (Brazil); Macario, Leilane Roberta [INCTMN, LIEC, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14800-900 Araraquara, SP (Brazil); Avansi, Waldir [Centro de Ciências Exatas e de Tecnologia, Departamento de Física, Universidade Federal de São Carlos, Jardim Guanabara, 13565-905 São Carlos, SP (Brazil); Moreira, Mario Lucio [Instituto de Física e Matemática, Universidade Federal de Pelotas, P.O. Box 354, Campus do Capão do Leão, 96001-970 Pelotas, RS (Brazil); Rosa, Ieda Lucia Viana, E-mail: ilvrosa@ufscar.br [INCTMN, LIEC, Departamento de Química, Universidade Federal de São Carlos, P.O. Box 676, 13565-905 São Carlos, SP (Brazil); Mastelaro, Valmor Roberto [Instituto de Física de São Carlos, Departamento de Física e Ciência dos Materiais, Universidade de São Paulo, P.O. Box 369, Av Trabalhador São Carlense 400, 13560-970 São Carlos, SP (Brazil); Varela, José Arana; Longo, Elson [INCTMN, LIEC, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14800-900 Araraquara, SP (Brazil)

2014-02-05

Highlights: • CaTiO{sub 3}:Eu{sup 3+} were obtained using low temperatures and very short reactional times. • The Eu{sup 3+} changes the local order–disorder of the [TiO{sub 6}] and [CaO{sub 12}] clusters. • Lifetime decay curves reveal two sites of symmetry of the Eu{sup 3+} in the CT matrix. • CaTiO{sub 3}:Eu{sup 3+} exhibit the strongest luminescent intensity and pure red color. -- Abstract: Pure Calcium Titanate (CT-pure) and Europium doped Calcium Titanate Ca{sub 1−x}Eu{sub x}TiO{sub 3} (x = 0.5%, 1.0% and 2.0% molar ratio of Eu{sup 3+} ions) powders were synthesized by hydrothermal microwave method (HTMW) at 140 °C for 8 min. The HTMW method appears to be an efficient method to prepare the luminescence materials using low temperatures and very short reactional times. In addition it is possible to determine specific correlations imposed by TiCl{sub 4} replacement by titanium isopropoxide [Ti(OC{sub 3}H{sub 7}){sub 4}] changing the reaction character and resulting in two different options of europium doping CT syntesis. To evaluate the influence of the structural order–disorder among the reactions and different properties of these materials, the following techniques were used for characterization. XANES spectroscopy that revealed that the introduction of Eu{sup 3+} ions into the CT lattice induces to significant changes in the local order–disorder around both, [TiO{sub 6}] and [CaO{sub 12}], complex clusters. PL spectra show Eu{sup 3+} emission lines ascribed to the Eu{sup 3+} transitions from {sup 5}D{sub 0} excited states to {sup 7}F{sub J} (J = 0, 1–4) fundamental states in CT:Eu{sup 3+} powders excited at 350 and 394 nm.

Novel bone substitute composed of chitosan and strontium-doped α-calcium sulfate hemihydrate: Fabrication, characterisation and evaluation of biocompatibility

International Nuclear Information System (INIS)

Chen, Yirong; Zhou, Yilin; Yang, Shenyu; Li, Jiao Jiao; Li, Xue; Ma, Yunfei; Hou, Yilong; Jiang, Nan; Xu, Changpeng; Zhang, Sheng; Zeng, Rong; Tu, Mei; Yu, Bin

2016-01-01

Calcium sulfate is in routine clinical use as a bone substitute, offering the benefits of biodegradability, biocompatibility and a long history of use in bone repair. The osteoconductive properties of calcium sulfate may be further improved by doping with strontium ions. Nevertheless, the high degradation rate of calcium sulfate may impede bone healing as substantial material degradation may occur before the healing process is complete. The purpose of this study is to develop a novel composite bone substitute composed of chitosan and strontium-doped α-calcium sulfate hemihydrate in the form of microcapsules, which can promote osteogenesis while matching the natural rate of bone healing. The developed microcapsules exhibited controlled degradation that facilitated the sustained release of strontium ions. In vitro testing showed that the microcapsules had minimal cytotoxicity and ability to inhibit bacterial growth. In vivo testing in a mouse model showed the absence of genetic toxicity and low inflammatory potential of the microcapsules. The novel microcapsules developed in this study demonstrated suitable degradation characteristics for bone repair as well as favourable in vitro and in vivo behaviour, and hold promise for use as an alternative bone substitute in orthopaedic surgery. - Highlights: • Chitosan + Sr-doped α-calcium sulfate hemihydrate microcapsules were synthesised. • The novel composite microcapsules had potential application as a bone substitute. • The microcapsules showed controlled degradation and release of strontium ions. • The microcapsules showed in vitro biocompatibility by cytotoxicity test. • The microcapsules showed in vivo biocompatibility in a mouse model.

Novel bone substitute composed of chitosan and strontium-doped α-calcium sulfate hemihydrate: Fabrication, characterisation and evaluation of biocompatibility

Energy Technology Data Exchange (ETDEWEB)

Chen, Yirong; Zhou, Yilin [Department of Orthopaedics and Traumatology, Nanfang Hospital, Southern Medical University, Guangzhou 510515 (China); Yang, Shenyu [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Li, Jiao Jiao [Biomaterials and Tissue Engineering Research Unit, School of AMME, University of Sydney, Sydney, NSW 2006 (Australia); Li, Xue; Ma, Yunfei; Hou, Yilong; Jiang, Nan; Xu, Changpeng; Zhang, Sheng [Department of Orthopaedics and Traumatology, Nanfang Hospital, Southern Medical University, Guangzhou 510515 (China); Zeng, Rong [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Tu, Mei, E-mail: tumei@jnu.edu.cn [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Yu, Bin, E-mail: yubinol@163.com [Department of Orthopaedics and Traumatology, Nanfang Hospital, Southern Medical University, Guangzhou 510515 (China)

2016-09-01

Calcium sulfate is in routine clinical use as a bone substitute, offering the benefits of biodegradability, biocompatibility and a long history of use in bone repair. The osteoconductive properties of calcium sulfate may be further improved by doping with strontium ions. Nevertheless, the high degradation rate of calcium sulfate may impede bone healing as substantial material degradation may occur before the healing process is complete. The purpose of this study is to develop a novel composite bone substitute composed of chitosan and strontium-doped α-calcium sulfate hemihydrate in the form of microcapsules, which can promote osteogenesis while matching the natural rate of bone healing. The developed microcapsules exhibited controlled degradation that facilitated the sustained release of strontium ions. In vitro testing showed that the microcapsules had minimal cytotoxicity and ability to inhibit bacterial growth. In vivo testing in a mouse model showed the absence of genetic toxicity and low inflammatory potential of the microcapsules. The novel microcapsules developed in this study demonstrated suitable degradation characteristics for bone repair as well as favourable in vitro and in vivo behaviour, and hold promise for use as an alternative bone substitute in orthopaedic surgery. - Highlights: • Chitosan + Sr-doped α-calcium sulfate hemihydrate microcapsules were synthesised. • The novel composite microcapsules had potential application as a bone substitute. • The microcapsules showed controlled degradation and release of strontium ions. • The microcapsules showed in vitro biocompatibility by cytotoxicity test. • The microcapsules showed in vivo biocompatibility in a mouse model.

Electrical and magnetic behavior of iron doped nickel titanate (Fe{sup 3+}/NiTiO{sub 3}) magnetic nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Lenin, Nayagam; Karthik, Arumugam; Sridharpanday, Mathu; Selvam, Mohanraj; Srither, Saturappan Ravisekaran; Arunmetha, Sundarmoorthy; Paramasivam, Palanisamy; Rajendran, Venkatachalam, E-mail: veerajendran@gmail.com

2016-01-01

Iron doped nickel titanate (Fe{sup 3+}/NiTiO{sub 3}) ferromagnetic nanoparticles with different concentrations of Fe (0.2, 0.4, and 0.6 mol) were synthesized using precipitation route with precursor source such as nickel nitrate and iron nitrate solutions. The prepared magnetic nanopowders were investigated through X-ray diffraction (XRD), Fourier transform infrared, scanning electron microscope, X-ray fluorescence, Brunauer–Emmett–Teller, vibrating sample magnetometer, and electrochemical impedance spectroscopy to explore the structural, ferromagnetic, and dielectric properties. The obtained XRD pattern shows formation of iron doped nickel titanate in orthorhombic structure. The crystallite size ranges from 57 to 21 nm and specific surface area ranges from 11 to 137 m{sup 2} g{sup −1}. The hysteresis loops of nanomagnetic materials show ferromagnetic behavior with higher magnitude of coercivity (H{sub c}) 867–462 Oe. The impedance analysis of ferromagnetic materials explores the ferro-dielectric behavior with enhanced properties of Fe{sup 3+}/NiTiO{sub 3} nanoparticles at higher Fe content. - Highlights: • Iron doped nickel titanate magnetic nanoparticles. • Ferromagnetic magnetism behavior with higher magnitude of coercivity. • Dielectric behavior of ferromagnetic nanoparticles with increase of Fe content.

Transformation kinetics in plasma-sprayed barium- and strontium-doped aluminosilicate (BSAS)

International Nuclear Information System (INIS)

Harder, B.J.; Faber, K.T.

2010-01-01

The hexacelsian-to-celsian phase transformation in Ba 1-x Sr x Al 2 Si 2 O 8 is of interest for environmental barrier coating applications. Plasma-sprayed microstructures were heat treated above 1100 o C and the kinetics of the hexacelsian-to-celsian transformation were quantified. Activation energies for bulk and crushed materials were determined to be ∼340 and ∼500 kJ mol -1 , respectively. X-ray diffraction and electron backscattered diffraction were used to establish how plasma spraying barium- and strontium-doped aluminosilicate effectively reduces the energy required for its transformation.

Characterization of barium strontium titanate thin films on sapphire substrate prepared via RF magnetron sputtering system

Science.gov (United States)

Jamaluddin, F. W.; Khalid, M. F. Abdul; Mamat, M. H.; Zoolfakar, A. S.; Zulkefle, M. A.; Rusop, M.; Awang, Z.

2018-05-01

Barium Strontium Titanate (Ba0.5Sr0.5TiO3) is known to have a high dielectric constant and low loss at microwave frequencies. These unique features are useful for many electronic applications. This paper focuses on material characterization of BST thin films deposited on sapphire substrate by RF magnetron sputtering system. The sample was then annealed at 900 °C for two hours. Several methods were used to characterize the structural properties of the material such as X-ray diffraction (XRD) and atomic force microscopy (AFM). Field emission scanning electron microscopy (FESEM) was used to analyze the surface morphology of the thin film. From the results obtained, it can be shown that the annealed sample had a rougher surface and better crystallinity as compared to as-deposited sample.

Modified cermet fuel electrodes for solid oxide electrochemical cells

Science.gov (United States)

Ruka, Roswell J.; Spengler, Charles J.

1991-01-01

An exterior porous electrode (10), bonded to a solid oxygen ion conducting electrolyte (13) which is in contact with an interior electrode (14), contains coarse metal particles (12) of nickel and/or cobalt, having diameters from 3 micrometers to 35 micrometers, where the coarse particles are coated with a separate, porous, multiphase layer (17) containing fine metal particles of nickel and/or cobalt (18), having diameters from 0.05 micrometers to 1.75 micrometers and conductive oxide (19) selected from cerium oxide, doped cerium oxide, strontium titanate, doped strontium titanate and mixtures thereof.

Computational study of structures of yttria-stabilised zirconia/strontium titanate multilayers

Energy Technology Data Exchange (ETDEWEB)

Cheah, Wei Li; Finnis, Mike [Imperial College London (United Kingdom)

2012-07-01

Growing interest in the field of functional oxide multilayered nano-heterostructures may be attributed to their unusual interfacial properties that are not yet fully understood. For instance, the nature of the unexpectedly high conductivity reported in a trilayer of 1-nm thick epitaxial yttria-stabilised zirconia (YSZ) film sandwiched between strontium titanate (STO) layers still remains controversial. In an effort to investigate the source of conductivity in this system, we first establish an unexpected YSZ lattice within such hetero-system using a combination of techniques - a genetic algorithm in which the interatomic forces are described by classical pair potentials, and a pseudo-potential-based DFT method as implemented in the plane-wave code CASTEP. We find this structure to be more stable than an anatase zirconia epitaxial lattice on STO which has been previously found as the most stable structure if yttrium dopants were not incorporated within the zirconia layer. Analysis of charge density of this new structure reveals not localised vacancies, but several small pockets of low charge densities for each expected vacancy. We examine the mobility of oxide ions in the hetero-system using classical molecular dynamics simulation and attempt to relate the results to experimental conductivity values.

Modified titanate perovskites in photocatalytic water splitting

Energy Technology Data Exchange (ETDEWEB)

Wlodarczak, M.; Ludwiczak, M.; Laniecki, M. [A. Mickiewicz Univ. (Poland)

2010-07-01

Received materials have structure of perovskite, what was shown by XRD diffraction patterns. Perovskite structure is present in all samples with strontium, barium and one sample with calcium. Moreover, received barium and strontium titanate are very similar to pattern materials. XRD results show, that temperature 500 C is too low to create perovskite structure in CaTiO{sub 3}. However, it is high enough in case of SrTiO{sub 3} and BaTiO{sub 3}. One regularity is obvious, surface area increases for samples calcined in lower temperature. There is a connection between surface area and dispersion of platinum. Both of them reach the greatest value to the calcium titanate. Catalytic activity was shown by all of received samples. Measurable values were received to samples calcined in 700 C. Calcium titanate had the best catalytic activity, both an amount of hydrogen and a ratio of hydrogen to platinum. There is one regularity to all samples, the ration of hydrogen to platinum increase when amount of platinum decrease. (orig.)

Synthesis and characterization of nanoporous strontium-doped lanthanum cobaltite thin film using metal organic chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Park, Jun-Sik [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, Young-Beom, E-mail: ybkim@hanyang.ac.kr [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-791 (Korea, Republic of)

2016-01-29

By employing strontium as a dopant of lanthanum cobaltite (LaCoO{sub 3}), strontium-doped lanthanum cobaltite (La{sub 1−x}Sr{sub x}CoO{sub 3−δ}, LSC) thin film was fabricated using a metal organic chemical solution deposition (MOCSD) method. Lanthanum nitrate hexahydrate [La(NO{sub 3}){sub 3}6H{sub 2}O], strontium acetate [Sr(CH{sub 3}COO){sub 2}], and cobalt acetate tetrahydrate [Co(CH{sub 3}COO){sub 2}4H{sub 2}O] were used as precursors. The coating process was performed through a spin coating method on a substrate, which were then heat treated under various temperature conditions. Electrical properties, microstructures, and crystalline structures with respect to sintering temperature were analyzed. According to these analyses, the change in surface morphology, phase shift, and conductive properties were closely related, which could explain their respective behaviors. Furthermore, sintered strontium-doped lanthanum perovskite oxides showed various conductivities according to the amount of dopant. With the molar ratio of strontium that is stoichiometrically equivalent to lanthanum (La{sub 0.5}Sr{sub 0.5}CoO{sub 3−δ}) thin film showed the best conductivity in the sintering temperature range of 650–700 °C, with perovskite phases formed at this temperature condition. As the electrically conductive properties of the thin film are a function of thickness, the films were coated several times to a thickness of approximately 300 nm, with the lowest resistivity (approximately 9.06 × 10{sup −4} Ω cm) observed at the optimized sintering temperature and solution composition. - Highlights: • LSC thin film was fabricated by metal organic chemical solution deposition (MOCSD). • The film shows good agreement on the electrical conductivity of LSC by conventional methods. • The properties of LSC film are influenced by the surface morphology and crystalline phase. • Optimal molar ratio of strontium for the highest conductivity was investigated.

Synthesis and silica coating of calcia-doped ceria/plate-like titanate (K0.8Li0.27Ti1.73O4) nanocomposite by seeded polymerization technique

International Nuclear Information System (INIS)

El-Toni, Ahmed Mohamed; Yin, Shu; Sato, Tsugio

2007-01-01

Calcia-doped ceria is of potential interest as an ultraviolet (UV) radiation blocking material in personal care products because of the excellent UV light absorption property and low catalytic ability for the oxidation of organic materials superior to undoped ceria. In order to reduce the oxidation catalytic activity further, calcia-doped ceria was coated with amorphous silica by means of seeded polymerization technique. Generally, nanoparticles of inorganic materials do not provide a good coverage for human skin because of the agglomeration of the particles. The plate-like particles are required to enhance the coverage ability of inorganic materials. This can be accomplished by synthesis of calcia-doped ceria/plate-like potassium lithium titanate (K 0.8 Li 0.27 Ti 1.73 O 4 ) nanocomposite with subsequent silica coating to control catalytic activity of calcia-doped ceria. Calcia-doped ceria/plate-like potassium lithium titanate nanocomposite was prepared by soft chemical method followed by silica coating via seeded polymerization technique. Silica coated calcia-doped ceria/plate-like potassium lithium titanate nanocomposite was characterized by X-ray diffraction, SEM, TEM, XPS and FT-IR

Effect of crystal structure on strontium titanate thin films and their dielectric properties

Science.gov (United States)

Kampangkeaw, Satreerat

Strontium titanate (SrTiO3 or STO) has application in radio and microwave-frequency tunable capacitor devices particularly at low temperatures due to its high dielectric constant, low loss and the electric field tunability of its dielectric constant. The main goal of improving the performance in these devices is to increase the tunability and decrease the dielectric loss at the same time, especially at microwave frequencies. Thin films of STO however, show dramatic differences compared to the bulk. The dielectric constant of bulk STO increases nonlinearly from 300 at room temperature to 30000 at 4 K and the loss range is 10-3--10 -4. On the other hand. STO thin films, while showing a dielectric constant close to 300 at room temperature, typically reach a maximum between 1000 and 10000 in the 30 K to 100 K range before decreasing, and the high-loss range is 10-2--10-3. We have grown strontium titanate thin films using a pulsed laser deposition technique on substrates selected to have a small lattice mismatch between the film and substrate. Neodymium gallate (NdGaO3 or NGO) and lanthanum aluminate (LaAlO3 or LAO) substrates were good candidates due to only 1--2% mismatching. Film capacitor devices were fabricated with 25 micron gap separation. 1.5 mm total gap length and an overall 1 x 2 mm dimension using standard lithography and gold metal evaporative techniques. Their nonlinear dielectric constant and loss tangent were measured at low frequencies and also at 2 GHz, and from room temperature down to 4 K. The resulting films show significant variations of dielectric properties with position on the substrates with respect to the deposition plume axis. In the presence of DC electric fields up to +/-4 V/mum, STO films show improved dielectric tunability and low loss in regions far from the plume axis. We found that the films grown on NCO have lower dielectric loss than those on LAO due to a closer match of the NCO lattice to that of STO. We investigated the possible

Frequency and Temperature Dependent Dielectric Properties of Free-standing Strontium Titanate Thin Films.

Science.gov (United States)

Dalberth, Mark J.; Stauber, Renaud E.; Anderson, Britt; Price, John C.; Rogers, Charles T.

1998-03-01

We will report on the frequency and temperature dependence of the complex dielectric function of free-standing strontium titanate (STO) films. STO is an incipient ferroelectric with electric-field tunable dielectric properties of utility in microwave electronics. The films are grown epitaxially via pulsed laser deposition on a variety of substrates, including lanthanum aluminate (LAO), neodymium gallate (NGO), and STO. An initial film of yttrium barium cuprate (YBCO) is grown on the substrate, followed by deposition of the STO layer. Following deposition, the sacrificial YBCO layer is chemically etched away in dilute nitric acid, leaving the substrate and a released, free-standing STO film. Coplanar capacitor structures fabricated on the released films allow us to measure the dielectric response. We observe a peak dielectric function in excess of 5000 at 35K, change in dielectric constant of over a factor of 8 for 10Volt/micron electric fields, and temperature dependence above 50K that is very similar to bulk material. The dielectric loss shows two peaks, each with a thermally activated behavior, apparently arising from two types of polar defects. We will discuss the correlation between dielectric properties, growth conditions, and strain in the free-standing STO films.

Amino acid-assisted synthesis of strontium hydroxyapatite bone ...

Indian Academy of Sciences (India)

Strontium-incorporated calcium phosphates show potential in biomedical application, particularly the doped stron- tium may ... shows that the addition of glycine plays an important role in reducing the particle size of strontium hydroxyapatite.

The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT).

Science.gov (United States)

Slouka, Christoph; Kainz, Theresa; Navickas, Edvinas; Walch, Gregor; Hutter, Herbert; Reichmann, Klaus; Fleig, Jürgen

2016-11-22

The different properties of acceptor-doped (hard) and donor-doped (soft) lead zirconate titanate (PZT) ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La 3+ donor-doped, Fe 3+ acceptor-doped and La 3+ /Fe 3+ -co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT.

The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT

Directory of Open Access Journals (Sweden)

Christoph Slouka

2016-11-01

Full Text Available The different properties of acceptor-doped (hard and donor-doped (soft lead zirconate titanate (PZT ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La3+ donor-doped, Fe3+ acceptor-doped and La3+/Fe3+-co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT.

Strontium-Doped Hematite as a Possible Humidity Sensing Material for Soil Water Content Determination

OpenAIRE

Tulliani, Jean-Marc; Baroni, Chiara; Zavattaro, Laura; Grignani, Carlo

2013-01-01

The aim of this work is to study the sensing behavior of Sr-doped hematite for soil water content measurement. The material was prepared by solid state reaction from commercial hematite and strontium carbonate heat treated at 900 °C. X-Ray diffraction, scanning electron microscopy and mercury intrusion porosimetry were used for microstructural characterization of the synthesized powder. Sensors were then prepared by uniaxially pressing and by screen-printing, on an alumina substrate, the prep...

Structure, dielectric and electrical properties of cerium doped barium zirconium titanate ceramics

International Nuclear Information System (INIS)

Feng Hongjun; Hou Jungang; Qu Yuanfang; Shan Dan; Yao Guohua

2012-01-01

Highlights: ► Rare-earth doped barium zirconate titanate (BZT) ceramics, Ba(Zr 0.25 Ti 0.75 )O 3 + xCeO 2 , (x = 0–1.5 at%) were obtained by a solid state reaction route. ► Morphological analysis on sintered samples by scanning electron microscopy shows that the addition of rare-earth ions affects the growth of the grain and remarkably changes the grain morphology. ► The effect of rare-earth addition to BZT on dielectric and electrical properties is analyzed, demonstrating that the samples with x = 0.4 and x = 0.6 could be semiconducting in air atmosphere. - Abstract: Rare-earth doped barium zirconium titanate (BZT) ceramics, Ba(Zr 0.25 Ti 0.75 )O 3 + xCeO 2 , (x = 0–1.5 at%) were obtained by a solid state reaction route. Perovskite-like single-phase compounds were confirmed from X-ray diffraction data and the lattice parameters were refined by the Rietveld method. It is found that, integrating with the lattice parameters and the distortion of crystal lattice, there is an alternation of substitution preference of cerium ions for the host cations in perovskite lattice. Morphological analysis on sintered samples by scanning electron microscopy shows that the addition of rare-earth ions affects the growth of the grain and remarkably changes the grain morphology. The effect of rare-earth addition to BZT on dielectric and electrical properties is analyzed. High values of dielectric tunability are obtained for cerium doped BZT. Especially, the experimental results on the effect of the contents of rare-earth addition on the resistivity of BZT ceramics were investigated, demonstrating that the samples with x = 0.4 and x = 0.6 could be semiconducting in air atmosphere.

Synthesis and characterization of novel lanthanide- and actinide-containing titanates and zircono-titanates; relevance to nuclear waste disposal

International Nuclear Information System (INIS)

Shoup, S.L.S.

1995-08-01

Before experiments using actinide elements are performed, synthetic routes are tested using lanthanides of comparable ionic radii as surrogates. Compound and solid solution formation in several lanthanide-containing titanate and zircono-titanate systems have been established using X-ray diffraction (XRD) analysis, which helped to define interesting and novel experiments, some of which have been performed and are discussed, for selected actinide elements. The aqueous solubilities of several lanthanide- and actinide-containing compounds, representative of the systems studied, were tested in several leachants, including the WIPP open-quotes Aclose quotes brine, following modified Materials Characterization Center procedures (MCC-3). The WIPP open-quotes Aclose quotes brine is a synthetic substitute for that found in nature at the Waste Isolation Pilot Plant (WIPP) in New Mexico. The concentrations of cerium, used as a surrogate for plutonium, leached by the WIPP open-quotes Aclose quotes brine from all the cerium-containing compounds and solid solutions tested were below the Inductively Coupled Plasma (ICP) atomic emission spectrometry limit of detection (10 ppm) established for cerium in this brine. The concentrations of plutonium leached from the two plutonium-containing solid solutions were less than 1 ppm as determined by gross alpha counting and alpha pulse height analysis. Concentrations of strontium leached by the WIPP brine from stable strontium containing titanate compounds, studied as possible immobilizers of both 90 Sr and actinide elements, were also quite low. These compound and solid solution formation investigations and the aqueous solubility studies suggest that the types of titanate and zircono-titanate compounds and solid solutions studied in this work appear to be useful as host matrices for nuclear waste immobilization

Electrical characterization of strontium titanate borosilicate glass ceramics system with bismuth oxide addition using impedance spectroscopy

International Nuclear Information System (INIS)

Thakur, O.P.; Kumar, Devendra; Parkash, Om; Pandey, Lakshman

2003-01-01

The ac electrical data, measured in the frequency range 0.1 kHz-1 MHz, were used to study the electrical response of strontium titanate borosilicate glass ceramic system with bismuth oxide addition. Complex plane plots from these electrical data for various glass ceramic samples reveal contributions from simultaneously operating polarization mechanisms to overall dielectric behavior. The complex modulus (M * ) representation of electrical data for various glass ceramic samples were found to be more informative. Equivalent circuit models, which represent the electrical behavior of glass ceramic samples, were determined using complex non-linear least square (CNLS) fitting. An attempt has been made to understand the dielectric behavior of various glass ceramics in terms of contributions arising from different polarization processes occurring at glassy matrix, crystalline phases, glass to crystal interface region and blocking electrodes. Glass ceramics containing SrTiO 3 and TiO 2 (rutile) phases show thermally stable dielectric behavior

P-doped strontium titanate grown using two target pulsed laser deposition for thin film solar cells

Science.gov (United States)

Man, Hamdi

Thin-film solar cells made of Mg-doped SrTiO3 p-type absorbers are promising candidates for clean energy generation. This material shows p-type conductivity and also demonstrates reasonable absorption of light. In addition, p-type SrTiO3 can be deposited as thin films so that the cost can be lower than the competing methods. In this work, Mg-doped SrTiO3 (STO) thin-films were synthesized and analyzed in order to observe their potential to be employed as the base semiconductor in photovoltaic applications. Mg-doped STO thin-films were grown by using pulsed laser deposition (PLD) using a frequency quadrupled Yttrium Aluminum Garnet (YAG) laser and with a substrate that was heated by back surface absorption of infrared (IR) laser light. The samples were characterized using X-ray photoelectron spectroscopy (XPS) and it was observed that Mg atoms were doped successfully in the stoichiometry. Reflection high energy electron diffraction (RHEED) spectroscopy proved that the thin films were polycrystalline. Kelvin Probe work function measurements indicated that the work function of the films were 4.167 eV after annealing. UV/Vis Reflection spectroscopy showed that Mg-doped STO thin-films do not reflect significantly except in the ultraviolet region of the spectrum where the reflection percentage increased up to 80%. Self-doped STO thin-films, Indium Tin Oxide (ITO) thin films and stainless steel foil (SSF) were studied in order to observe their characteristics before employing them in Mg-doped STO based solar cells. Self-doped STO thin films were grown using PLD and the results showed that they are capable of serving as the n-type semiconductor in solar cell applications with oxygen vacancies in their structure and low reflectivity. Indium Tin Oxide thin-films grown by PLD system showed low 25-50 ?/square sheet resistance and very low reflection features. Finally, commercially available stainless steel foil substrates were excellent substrates for the inexpensive growth of

Synthesis of Nb-doped SrTiO₃ by a modified glycine-nitrate process

DEFF Research Database (Denmark)

Blennow Tullmar, Peter; Kammer Hansen, Kent; Wallenberg, L.R.

2007-01-01

The objective of the present investigation was to develop a technique to synthesize submicronic particles of Nb-doped strontium titanate with a homogeneous composition. This was achieved by a modified glycine-nitrate process, using Ti-lactate, Nb-oxalate, and Sr(NO3)(2) as starting materials....... A combination of both citric acid and glycine was needed in order to integrate the useful features of both complexation and combustion natures of citric acid and glycine, respectively. The amount of citric acid, glycine, and nitrates in the starting solution, as well as the source for extra nitrates...

A comparative study of strontium and titanium doped mullite in PVDF matrix and their phase behavior, microstructure and electrical properties

Energy Technology Data Exchange (ETDEWEB)

Paul, Biplab Kumar; Roy, Debasis; Batabyal, Sreejita [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Bhattacharya, Alakananda [West Bengal State University, Kolkata (India); Nandy, Papiya [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Das, Sukhen, E-mail: sdasphysics@gmail.com [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Indian Institute of Engineering Science and Technology, Shibpur (India)

2017-02-01

We have discussed the dielectric behavior, phase behavior, microstructure and electrical properties of strontium and titanium induced aluminno-silicate ceramic composite system doped in PVDF (Polyvinyliden fluoride) matrix, with different molar concentration of titanium and strontium salts prepared via sol-gel route. The frequency dispersions of permittivity, conductivity and dissipation factor were investigated in detail. This paper demonstrates that the loading of a conductive component into a highly insulating matrix is an effective way to fabricate composites with simultaneously high permittivity. The incorporation of these metal doped mullite composites on PVDF can be used as dielectric material for the fabrication of high charge storing multilayer capacitors and also a promising candidate for electronic industries. - Highlights: • We have synthesized mullite composites with high dielectric constants. • High charge storing multilayer capacitors require a material with high dielectric constant. • The material developed will be perfect for the applications of embedded capacitors. • The material we have synthesized is a promising candidate for electronic industries.

Study of mineral ion exchangers for strontium removal from nuclear waste waters

International Nuclear Information System (INIS)

Merceille, A.

2012-01-01

The problems of chemical pollution of water have become a major concern and a priority for the nuclear industry. The aim of this work is to study some ion exchangers used for the removal of strontium ions because 90 Sr is one of a major pollutant in nuclear liquid wastes. This study allows linking the physical and chemical properties of these materials and their sorption properties. This work presents therefore the synthesis of two materials - sodium nona-titanate and zeolite A - selected for their specific sorption properties of strontium: A second part of this work is dedicated to the study of specific exchange capacities of these materials for the strontium in presence of other elements such as sodium and calcium. Batch experiments were performed and kinetic and ion exchange models have been applied to understand the selectivity of the materials for strontium removal. Sodium nona-titanate and zeolite A are also studied in actual effluents. Monoliths of zeolite A have been also tested in dynamic ion exchange process. This material is promising for the treatment of radioactive effluents in continuous flow because it joins the sorption properties of the zeolite powder with the advantage of a solid with a macroporous network. (author) [fr

Effects of Nb and Sr doping on crystal structure of epitaxial BaTiO3 thin films on MgO substrates

International Nuclear Information System (INIS)

Kim, Yongsam; Chen, Chunhua; Saiki, Atsushi; Wakiya, Naoki; Shinozaki, Kazuo; Mizutani, Nobuyasu

2002-01-01

Niobium (Nb) and strontium (Sr) doped barium titanate (BT) films were deposited by radio frequency (RF) magnetron sputtering with Nb and Sr doped BT ceramic targets, respectively. The effect of Nb and Sr doping on the crystal structure of epitaxial BaTiO 3 thin films on MgO substrates was investigated. The crystal structure of the films was examined using the reciprocal space mapping measurement. All the films exhibit a cube-on-cube relation with respect to the substrates. As the amount of doped Sr increased, both of the in-plane and out-of-plane lattice constants of Sr doped BT films slowly approached the BT bulk values. On the other hand, the lattice constants of Nb doped BT films were rapidly coming close to the bulk values. These indicated that the lattices of doped BT films were relaxed as the amount of doped elements increased. In addition, Nb doping had greater influence on the relaxation of the films than Sr doping for the same content of dopant. (author)

Atomic layer deposition of epitaxial layers of anatase on strontium titanate single crystals: Morphological and photoelectrochemical characterization

Energy Technology Data Exchange (ETDEWEB)

Kraus, Theodore J.; Nepomnyashchii, Alexander B.; Parkinson, B. A., E-mail: bparkin1@uwyo.edu [Department of Chemistry, School of Energy Resources, University of Wyoming, Laramie, Wyoming 82071 (United States)

2015-01-15

Atomic layer deposition was used to grow epitaxial layers of anatase (001) TiO{sub 2} on the surface of SrTiO{sub 3} (100) crystals with a 3% lattice mismatch. The epilayers grow as anatase (001) as confirmed by x-ray diffraction. Atomic force microscope images of deposited films showed epitaxial layer-by-layer growth up to about 10 nm, whereas thicker films, of up to 32 nm, revealed the formation of 2–5 nm anatase nanocrystallites oriented in the (001) direction. The anatase epilayers were used as substrates for dye sensitization. The as received strontium titanate crystal was not sensitized with a ruthenium-based dye (N3) or a thiacyanine dye (G15); however, photocurrent from excited state electron injection from these dyes was observed when adsorbed on the anatase epilayers. These results show that highly ordered anatase surfaces can be grown on an easily obtained substrate crystal.

Gas thermodesorption study of barium and strontium cerates

International Nuclear Information System (INIS)

Aksenova, T.I.; Khromushin, I.V.; Zhotabaev, Zh.R.; Bukenov, K.D.; Medvedeva, Z.V.; Berdauletov, A.K.

2002-01-01

Kinetic of water, oxygen, hydrogen and carbon dioxide molecules release from doped and undoped samples of barium cerates and doped strontium cerates during vacuum heating was studied. The samples were prepared by inductive melting method. The following two kinds of preliminary samples treatments were used: annealing in air (650-750 deg. C) and wet nitrogen atmosphere (625 deg.C). Main results of thermodesorption studies of barium and strontium cerates are represented in the table. The samples of doped LaSrMnO were investigated also. It was found that the initial doped samples (without preliminary annealing) did not show any gas release in temperature range of 20-1100 deg. C. This fact indicates on high stability of compositions and strong bond of 'host' oxygen in their lattice. A significant amount of water and oxygen molecules were released from BaCe 0.9 Nd 0.1 O 3 samples whereas water and hydrogen molecules desorption from SrCe 0.95 Y 0.05 O 3 samples took place. Hydrogen molecules desorption was found for strontium cerates samples; no hydrogen molecules release was observed for doped and pure barium cerate samples.Intensive water molecules release from doped samples confirms the necessity of oxygen vacancies creation in these compounds to get properties of proton conductivity, since it was not found any water molecules release from annealed undoped samples of BaCeO 3 It is necessary to notice that oxygen molecules release from these samples took place at ∼1000 deg. C that is significantly higher then from BaCeNdO samples. Forms of high temperatures part of oxygen and low temperature part of water spectra indicate that phase transformations are responsible for oxygen and water molecules desorption in this cases. These results are in good agreement with literature data. Desorption of water molecules from barium and strontium cerates took place. Oxygen desorption took place only from barium cerates. It can be explained as the following: doped barium cerates have

Atom states and interatomic interactions in complex perovskite-like oxides. Communication XX. Origin of electron-ionic conductivity in lanthanum gallates doped with strontium and chromium

International Nuclear Information System (INIS)

Chezhina, N.V.; Zolotukhina, N.V.; Pijr, I.V.

2006-01-01

Magnetic susceptibilities and electric conductivities of solid solutions based on lanthanum gallate containing chromium and strontium atoms in the ratio of 10 : 2 were studied. It was shown that no partial oxidation of chromium to Cr(IV) occurs when lanthanum gallate is doped with chromium and strontium simultaneously, whereas the ionic conductivity is associated with the appearance of vacancies stabilized by chromium atoms in the oxygen sublattice [ru

Characterization of barium titanate powder doped with sodium and potassium ions by using Rietveld refining; Caracterizacao do po de titanato de bario dopado com ions sodio e potasio com o refinamento de Rietveld

Energy Technology Data Exchange (ETDEWEB)

Andrade, M.C.; Assis, J.T.; Pereira, F.R., E-mail: mcalixto@iprj.uerj.b [Universidade do Estado do Rio de Janeiro (IPRJ/UERJ), Nova Friburgo, RJ (Brazil). Instituto Politecnico; Araujo, J.C. [Universidade do Estado do Rio de Janeiro (FFP/UERJ), Sao Goncalo, RJ (Brazil). Fac. de Formacao de Professores; Moreira, E.L.; Moraes, V.C.A.; Lopes, A.R. [Centro Brasileiro de Pesquisas Fisicas (CBPF/MCT), Rio de Janeiro, RJ (Brazil)

2009-07-01

A solid-reaction synthesis of doped barium titanate was done by employing barium carbonates, sodium, potassium and titanium oxides with classic procedures. Rietveld refining of X ray diffraction data of perovskite samples with tetragonal symmetry was applying and show good agreement. Besides, the treatment performed from 600 deg C produces nanocrystals of barium titanate with average size of 33 nm. The presence of endothermic peaks related to BaTiO{sub 3} formation at relatively low temperatures was determined by thermal analysis. A pseudo-Voigt Thompson-Cox-Hastings function was used to fit the standard samples of barium titanate. The Rietveld method has showed be efficient to detect the influences of temperature and doping on barium titanate microstructures. (author)

Human Internal Contamination with Strontium-90 Titanate; Contamination Interne du Corps Humain par le Titanate de Strontium 90; 0412 041d 0414 ; Contaminacion Interna del Cuerpo Humano con Titanato de Estroncio-90

Energy Technology Data Exchange (ETDEWEB)

Bradley, F. J.; Wald, N.; Wechsler, R. L. [Graduate School of Public Health and School of Medicine, University of Pittsburgh, Pittsburgh, PA (United States)

1964-11-15

Strontium-90 has been used in multikilocurie quantities recently as a heat source for thermoelectric generators. The titanate was carefully selected for this purpose as the chemical form which best met requirements including inertness to corrosive attack in the event of accidental release to the environment. An industrial accidental exposure of one worker on 26 June 1963 to strontium-90 titanate powder, originally in the form of particles of about 120 {mu}m and less, provided an opportunity to attempt the assessment of the human body burden of this supposedly highly insoluble compound. Because of the physical and biological behaviour of the particles, it was assumed that the actual particle size which was dispersed and ingested and/or inhaled by the exposed person was in the range of 1 to 30 {mu}m. Three techniques were used to estimate the body burden. Whole-body radiation counting carried out by Dr. Charles H. Miller at Argonne National Laboratory, which only gave an upper limit because of the non-specific Bremsstrahlung spectrum from strontium-90, yttrium-90 indicated an initial total-body burden of 4.8 {mu}c. The second method, total urinary and faecal output collection, totalled 5.0 for the first 20 d. Combining that amount with an estimate of the amount retained in the body, an initial total-body burden of 5.2 {mu}c was obtained. The third technique, blood radioactivity determination, indicated an initial total-body burden of 6 {mu}c. The ratio of faecal to urinary output in the first 20 d was 15 to 1, and 94% of the total strontium-90 excretion was via the gastro-intestinal tract. It is of interest, however, that a significant fraction was evidently soluble. By the 20th post-incident day, it was estimated that the retained body burden was only 5% of the total intake. Methods used in that period to enhance faecal excretion by MgSO{sub 4} and urinary excretion by a combination of Ca-gluconate and NH{sub 4}CI are described. Subsequent excretion patterns and the

Growth and micro structural studies on Yittria Stabilized Zirconia (YSZ) and Strontium Titanate (STO) buffer layers

Energy Technology Data Exchange (ETDEWEB)

Srinivas, S.; Bhatnagar, A.K. [Univ. of Hyderabad (India); Pinto, R. [Solid State Electronics Group, Bombay (India)] [and others

1994-12-31

Microstructure of Yittria Stabilized Zirconia (YSZ) and Strontium Titanate (STO) of radio frequency magnetron sputtered buffer layers was studied at various sputtering conditions on Si<100>, Sapphire and LaAlO{sub 3} <100> substrates. The effect of substrate temperatures upto 800 C and sputtering gas pressures in the range of 50 mTorr. of growth conditions was studied. The buffer layers of YSZ and STO showed a strong tendency for columnar structure with variation growth conditions. The buffer layers of YSZ and STO showed orientation. The tendency for columnar growth was observed above 15 mTorr sputtering gas pressure and at high substrate temperatures. Post annealing of these films in oxygen atmosphere reduced the oxygen deficiency and strain generated during growth of the films. Strong c-axis oriented superconducting YBa{sub 2}Cu{sub 9}O{sub 7-x} (YBCO) thin films were obtained on these buffer layers using pulsed laser ablation technique. YBCO films deposited on multilayers of YSZ and STO were shown to have better superconducting properties.

Influence of Tm-doping on microstructure and luminescence behavior of barium strontium titanate thick films

International Nuclear Information System (INIS)

Wang Jingyang; Zhang Tianjin; Pan Ruikun; Ma Zhijun; Wang Jinzhao

2012-01-01

Tm-doped Ba 0.8 Sr 0.2 TiO 3 thick films were prepared by the screen-printing technique on the alumina substrate. The microstructure of the Tm-doped BST thick films was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy, respectively. All the samples showed a typical perovskite polycrystalline structure when sintered at 1260 °C. The substitution behavior of Tm 3+ ion in BST was found to change with increasing the Tm 3+ concentration. The observed Tm-related red emission reaches the maximum at 0.2 mol% Tm 3+ concentration. The effects of concentration quenching on the luminescence intensity were discussed.

Off Axis Growth of Strontium Titanate Films with High Dielectric Constant Tuning and Low Loss

Science.gov (United States)

Kampangkeaw, Satreerat

2002-03-01

Using off-axis pulsed laser deposition, we have grown strontium titanate (STO) films on neodymium gallate (NGO) and lanthanum aluminate (LAO) substrates. We measured the film dielectric constant and loss tangent as a function of temperature in the 10kHz to 1 MHz frequency range. We found that the loss is less than 0.01 We also obtained a figure of merit from the relative variation of the dielectric constant divided by the loss tangent. The obtained figured of merit at 35K and 1MHz is about 1000 comparable to bulk values. The dielectric constant of these films can be changed by a factor of 4-8 in the presence of a DC electric field up to 5V/μm. The films show significant variations of dielectric properties grown on different substrates at different locations respect to the axis of the plume. The STO films on LAO having high dielectric constant and dielectric tuning were grown in region near the center of the plume. On the other hand, STO on NGO shows this effect only on the films grown far from the plume axis.

Surface Roughness and Grain Size Characterization of Annealing Temperature Effect For Growth Gallium and Tantalum Doped Ba0.5 Sr0.5TiO3Thin Film

Directory of Open Access Journals (Sweden)

Irzaman

2009-01-01

Full Text Available Thin films 10 % gallium oxide doped barium strontium titanate (BGST and 10 % tantalum oxide doped barium strontium titanate (BTST were prepared on p-type Si (100 substrates using chemical solution deposition (CSD method with 1.00 M precursor. The films were deposited by spin coating method with spinning speed at 3000 rpm for 30 seconds. The post deposition annealing of the films were carried out in a furnace at 200oC, 240oC, 280oC (low temperature for 1 hour in oxygen gas atmosphere. The surface roughness and grain size analysis of the grown thin films are described by atomic force microscope (AFM method at 5000 nm x 5000 nm area. The rms surface roughness BGST thin films at 5000 nm x 5000 nm area are 0.632 nm, 0.564 nm, 0.487 nm for temperature 200oC, 240oC, 280oC, respectively, whereas the grain size (mean diameter are 238.4 nm, 219.0 nm, 185.1 nm for temperature 200oC, 240oC, 280oC, respectively. In fact, to increase annealing temperature from 200oC to 280oC would result in decreasing the rms roughness and grain size. Therefore, rms roughness and grain size would have the strong correlation annealing temperature.

Impact of Strontium Nitrate and Sodium Permanganate Addition on Solid-Liquid Separation of SRS High Level Waste

International Nuclear Information System (INIS)

Poirier, M.R.

2002-01-01

As a pretreatment step for the caustic side solvent extraction (CSSX) flowsheet, the process contacts the incoming salt solution containing entrained sludge with monosodium titanate (MST) to adsorb strontium and actinides. An operation filters the resulting slurry to remove the sludge and MST. Previous work for the River Protection Program at Hanford suggests that addition of strontium nitrate and sodium permanganate for strontium and actinide removal, rather than MST, improves the filtration rate for comparable waste streams

Electrochemically assisted deposition of strontium modified magnesium phosphate on titanium surfaces

International Nuclear Information System (INIS)

Meininger, M.; Wolf-Brandstetter, C.; Zerweck, J.; Wenninger, F.; Gbureck, U.; Groll, J.; Moseke, C.

2016-01-01

Electrochemically assisted deposition was utilized to produce ceramic coatings on the basis of magnesium ammonium phosphate (struvite) on corundum-blasted titanium surfaces. By the addition of defined concentrations of strontium nitrate to the coating electrolyte Sr 2+ ions were successfully incorporated into the struvite matrix. By variation of deposition parameters it was possible to fabricate coatings with different kinetics of Sr 2+ into physiological media, whereas the release of therapeutically relevant strontium doses could be sustained over several weeks. Morphological and crystallographic examinations of the immersed coatings revealed that the degradation of struvite and the release of Sr 2+ ions were accompanied by a transformation of the coating to a calcium phosphate based phase similar to low-crystalline hydroxyapatite. These findings showed that strontium doped struvite coatings may provide a promising degradable coating system for the local application of strontium or other biologically active metal ions in the implant–bone interface. - Highlights: • Sr-doped struvite coatings have been deposited on titanium by electrochemically assisted deposition. • Sr content can be adjusted by means of process time, current density and pulse mode. • Sr-doped coatings release therapeutically relevant Sr doses in physiological media for several weeks. • During immersion in physiological media Sr-doped struvite coatings transform into a low crystalline calcium phosphate phase.

Investigation of the additive induced doping effects in gelcast soft lead zirconate titanate ceramics

International Nuclear Information System (INIS)

Guo Dong; Cai Kai; Li Longtu; Gui Zhilun

2009-01-01

Due to the high sensitivity of the electrical properties of electronic ceramics to various factors, knowledge about the possible influence of the processing procedure on their electrical performance is critical for applying a new technique to the fabrication of the materials. In this study, various electrical parameters, complex impedance spectra, ferroelectric hysteresis loops, and microstructures of soft lead zirconate titanate (PZT) ceramics formed by the gelcasting technique from suspensions with various dispersants were investigated in comparison with those of the conventional dry pressed ones. We found that the sodium ion, which is the main cation in many commercial surfactants, exhibited obvious hard doping effects; thus causing deteriorated performance of the gelcast PZT ceramics. While a certain impurity ion introduced by a dispersant was also found to induce soft doping characteristics and improve the electrical performance of the materials. The results suggest that the doping effects of the metal ions or impurities introduced by the dispersants, or other additives, should be generally considered for applying a wet processing technique to forming multicomponent electronic ceramics.

Facile synthesis and enhanced visible light photocatalytic activity of N and Zr co-doped TiO2 nanostructures from nanotubular titanic acid precursors

Science.gov (United States)

Zhang, Min; Yu, Xinluan; Lu, Dandan; Yang, Jianjun

2013-12-01

Zr/N co-doped TiO2 nanostructures were successfully synthesized using nanotubular titanic acid (NTA) as precursors by a facile wet chemical route and subsequent calcination. These Zr/N-doped TiO2 nanostructures made by NTA precursors show significantly enhanced visible light absorption and much higher photocatalytic performance than the Zr/N-doped P25 TiO2 nanoparticles. Impacts of Zr/N co-doping on the morphologies, optical properties, and photocatalytic activities of the NTA precursor-based TiO2 were thoroughly investigated. The origin of the enhanced visible light photocatalytic activity is discussed in detail.

The effect of strontium doping on structural and morphological properties of ZnO nanofilms synthesized by ultrasonic spray pyrolysis method

Directory of Open Access Journals (Sweden)

A. Ouhaibi

2018-03-01

Full Text Available Pristine and strontium doped ZnO nanometric films were successfully synthesized on heated glass substrates by the ultrasonic spray pyrolysis technique. The samples were characterized by means of X-ray diffraction (XRD, Atomic Force Microscope (AFM, UV–visible spectroscopy and photoluminescence (PL. X-ray diffraction patterns confirmed the hexagonal (wurtzite structure, where the most pronounced (002 peak indicates the preferential orientation along the c-axis perpendicular to the sample surface. The intensity of this peak was increased rapidly from the first doping of 1% and its position was shifted toward higher angles under Sr-doping effect. For the used doping range of 1–5%, the Sr-doping at 3% attracted an especial attention. At this concentration, the particular transformation in the surface morphology of doped ZnO films was observed. The surface became granular and rough by expanding the crystallites' size. From optical measurements, transmittance and PL spectra were found to be sensitive to Sr-doping, where two different behaviors were observed before and after 3% of Sr-doping. Keywords: Ultrasonic spray pyrolysis, Sr-doped ZnO, Morphology study, Optical properties

Electrochemically assisted deposition of strontium modified magnesium phosphate on titanium surfaces

Energy Technology Data Exchange (ETDEWEB)

Meininger, M. [Department for Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, D-97070 Würzburg (Germany); Wolf-Brandstetter, C. [Max Bergmann Center for Biomaterials, Technical University of Dresden, Budapester Straße 27, D-01069 Dresden (Germany); Zerweck, J.; Wenninger, F.; Gbureck, U.; Groll, J. [Department for Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, D-97070 Würzburg (Germany); Moseke, C., E-mail: claus.moseke@fmz.uni-wuerzburg.de [Department for Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, D-97070 Würzburg (Germany)

2016-10-01

Electrochemically assisted deposition was utilized to produce ceramic coatings on the basis of magnesium ammonium phosphate (struvite) on corundum-blasted titanium surfaces. By the addition of defined concentrations of strontium nitrate to the coating electrolyte Sr{sup 2+} ions were successfully incorporated into the struvite matrix. By variation of deposition parameters it was possible to fabricate coatings with different kinetics of Sr{sup 2+} into physiological media, whereas the release of therapeutically relevant strontium doses could be sustained over several weeks. Morphological and crystallographic examinations of the immersed coatings revealed that the degradation of struvite and the release of Sr{sup 2+} ions were accompanied by a transformation of the coating to a calcium phosphate based phase similar to low-crystalline hydroxyapatite. These findings showed that strontium doped struvite coatings may provide a promising degradable coating system for the local application of strontium or other biologically active metal ions in the implant–bone interface. - Highlights: • Sr-doped struvite coatings have been deposited on titanium by electrochemically assisted deposition. • Sr content can be adjusted by means of process time, current density and pulse mode. • Sr-doped coatings release therapeutically relevant Sr doses in physiological media for several weeks. • During immersion in physiological media Sr-doped struvite coatings transform into a low crystalline calcium phosphate phase.

Amorphous boron-doped sodium titanates hydrates: Efficient and reusable adsorbents for the removal of Pb{sup 2+} from water

Energy Technology Data Exchange (ETDEWEB)

Di Bitonto, Luigi; Volpe, Angela; Pagano, Michele; Bagnuolo, Giuseppe; Mascolo, Giuseppe [CNR-IRSA, Via de Blasio 5, 70132 Bari (Italy); La Parola, Valeria [CNR-ISMN, Via U. La Malfa, 153, 90146 Palermo (Italy); Di Leo, Paola [CNR-IMAA, Via S. Loja, Tito Scalo (PZ) (Italy); Pastore, Carlo, E-mail: carlo.pastore@ba.irsa.cnr.it [CNR-IRSA, Via de Blasio 5, 70132 Bari (Italy)

2017-02-15

Highlights: • Amorphous B-doped sodium titanates hydrates were mildly synthesized. • These compounds resulted efficiently used in removing Pb{sup 2+} from natural water. • Adsorption occurs with a partial ionic exchange mechanism. • Adsorbents were easily recoverable and reusable for further new cycles. - Abstract: Amorphous titanium hydroxide and boron-doped (B-doped) sodium titanates hydrates were synthetized and used as adsorbents for the removal of Pb{sup 2+} from water. The use of sodium borohydride (NaBH{sub 4}) and titanium(IV) isopropoxide (TTIP) as precursors permits a very easy synthesis of B-doped adsorbents at 298 K. The new adsorbent materials were first chemically characterized (XRD, XPS, SEM, DRIFT and elemental analysis) and then tested in Pb{sup 2+} adsorption batch experiments, in order to define kinetics and equilibrium studies. The nature of interaction between such sorbent materials and Pb{sup 2+} was also well defined: besides a pure adsorption due to hydroxyl interaction functionalities, there is also an ionic exchange between Pb{sup 2+} and sodium ions even working at pH 4.4. Langmuir model presented the best fitting with a maximum adsorption capacity up to 385 mg/g. The effect of solution pH and common ions (i.e. Na{sup +}, Ca{sup 2+} and Mg{sup 2+}) onto Pb{sup 2+} sorption were also investigated. Finally, recovery was positively conducted using EDTA. Very efficient adsorption (>99.9%) was verified even using tap water spiked with traces of Pb{sup 2+} (50 ppb).

Low leakage Ru-strontium titanate-Ru metal-insulator-metal capacitors for sub-20 nm technology node in dynamic random access memory

Energy Technology Data Exchange (ETDEWEB)

Popovici, M., E-mail: Mihaela.Ioana.Popovici@imec.be; Swerts, J.; Redolfi, A.; Kaczer, B.; Aoulaiche, M.; Radu, I.; Clima, S.; Everaert, J.-L.; Van Elshocht, S.; Jurczak, M. [Imec, Leuven 3001 (Belgium)

2014-02-24

Improved metal-insulator-metal capacitor (MIMCAP) stacks with strontium titanate (STO) as dielectric sandwiched between Ru as top and bottom electrode are shown. The Ru/STO/Ru stack demonstrates clearly its potential to reach sub-20 nm technology nodes for dynamic random access memory. Downscaling of the equivalent oxide thickness, leakage current density (J{sub g}) of the MIMCAPs, and physical thickness of the STO have been realized by control of the Sr/Ti ratio and grain size using a heterogeneous TiO{sub 2}/STO based nanolaminate stack deposition and a two-step crystallization anneal. Replacement of TiN with Ru as both top and bottom electrodes reduces the amount of electrically active defects and is essential to achieve a low leakage current in the MIM capacitor.

Novel strontium-doped bioactive glass nanoparticles enhance proliferation and osteogenic differentiation of human bone marrow stromal cells

Energy Technology Data Exchange (ETDEWEB)

Strobel, L. A. [University of Erlangen-Nuremberg Medical Center, Department of Plastic and Hand Surgery (Germany); Hild, N.; Mohn, D.; Stark, W. J. [ETH Zurich, Department of Chemistry and Applied Biosciences, Institute for Chemical and Bioengineering (Switzerland); Hoppe, A. [University of Erlangen-Nuremberg, Department of Materials Science and Engineering, Institute of Biomaterials (Germany); Gbureck, U. [University of Wuerzburg, Department for Functional Materials in Medicine and Dentistry (Germany); Horch, R. E.; Kneser, U. [University of Erlangen-Nuremberg Medical Center, Department of Plastic and Hand Surgery (Germany); Boccaccini, A. R., E-mail: aldo.boccaccini@ww.uni-erlangen.de [University of Erlangen-Nuremberg, Department of Materials Science and Engineering, Institute of Biomaterials (Germany)

2013-07-15

The present study investigates a new family of bioactive glass nanoparticles with and without Sr-doping focusing on the influence of the nanoparticles on human bone marrow stromal cells (hBMSCs) in vitro. The bioactive glass nanoparticles were fabricated by flame spray synthesis and a particle diameter of 30-35 nm was achieved. Glass nanoparticles were undoped (BG 13-93-0Sr) or doped with 5 wt% strontium (Sr) (BG 13-93-5Sr) and used at concentrations of 10 and 100 {mu}g/cm Superscript-Two (particles per culture plate area), respectively. Cells were cultured for 14 days after which the samples were analysed regarding metabolic activity and expression of various bone-specific genes. Cell growth and morphology indicated the high cytocompatibility of the nanoparticulate bioactive glass. The presence of the nanoparticles enhanced cell growth compared to the plain polystyrene control group. At a concentration of 100 {mu}g/cm Superscript-Two , Sr-doped particles led to significantly enhanced gene expression of osteocalcin, collagen type 1 and vascular endothelial growth factor. Thus, Sr-doped nanoparticles showing a dose-dependent increase of osteogenic differentiation in hBMSCs are a promising biomaterial for bone regeneration purposes.

Novel strontium-doped bioactive glass nanoparticles enhance proliferation and osteogenic differentiation of human bone marrow stromal cells

International Nuclear Information System (INIS)

Strobel, L. A.; Hild, N.; Mohn, D.; Stark, W. J.; Hoppe, A.; Gbureck, U.; Horch, R. E.; Kneser, U.; Boccaccini, A. R.

2013-01-01

The present study investigates a new family of bioactive glass nanoparticles with and without Sr-doping focusing on the influence of the nanoparticles on human bone marrow stromal cells (hBMSCs) in vitro. The bioactive glass nanoparticles were fabricated by flame spray synthesis and a particle diameter of 30–35 nm was achieved. Glass nanoparticles were undoped (BG 13-93-0Sr) or doped with 5 wt% strontium (Sr) (BG 13-93-5Sr) and used at concentrations of 10 and 100 μg/cm² (particles per culture plate area), respectively. Cells were cultured for 14 days after which the samples were analysed regarding metabolic activity and expression of various bone-specific genes. Cell growth and morphology indicated the high cytocompatibility of the nanoparticulate bioactive glass. The presence of the nanoparticles enhanced cell growth compared to the plain polystyrene control group. At a concentration of 100 μg/cm², Sr-doped particles led to significantly enhanced gene expression of osteocalcin, collagen type 1 and vascular endothelial growth factor. Thus, Sr-doped nanoparticles showing a dose-dependent increase of osteogenic differentiation in hBMSCs are a promising biomaterial for bone regeneration purposes

Novel strontium-doped bioactive glass nanoparticles enhance proliferation and osteogenic differentiation of human bone marrow stromal cells

Science.gov (United States)

Strobel, L. A.; Hild, N.; Mohn, D.; Stark, W. J.; Hoppe, A.; Gbureck, U.; Horch, R. E.; Kneser, U.; Boccaccini, A. R.

2013-07-01

The present study investigates a new family of bioactive glass nanoparticles with and without Sr-doping focusing on the influence of the nanoparticles on human bone marrow stromal cells (hBMSCs) in vitro. The bioactive glass nanoparticles were fabricated by flame spray synthesis and a particle diameter of 30-35 nm was achieved. Glass nanoparticles were undoped (BG 13-93-0Sr) or doped with 5 wt% strontium (Sr) (BG 13-93-5Sr) and used at concentrations of 10 and 100 μg/cm² (particles per culture plate area), respectively. Cells were cultured for 14 days after which the samples were analysed regarding metabolic activity and expression of various bone-specific genes. Cell growth and morphology indicated the high cytocompatibility of the nanoparticulate bioactive glass. The presence of the nanoparticles enhanced cell growth compared to the plain polystyrene control group. At a concentration of 100 μg/cm², Sr-doped particles led to significantly enhanced gene expression of osteocalcin, collagen type 1 and vascular endothelial growth factor. Thus, Sr-doped nanoparticles showing a dose-dependent increase of osteogenic differentiation in hBMSCs are a promising biomaterial for bone regeneration purposes.

Dielectric relaxation of barium strontium titanate and application to thin films for DRAM capacitors

Science.gov (United States)

Baniecki, John David

This thesis examines the issues associated with incorporating the high dielectric constant material Barium Strontium Titanate (BSTO) in to the storage capacitor of a dynamic random access memory (DRAM). The research is focused on two areas: characterizing and understanding the factors that control charge retention in BSTO thin films and modifying the electrical properties using ion implantation. The dielectric relaxation of BSTO thin films deposited by metal-organic chemical vapor deposition (MOCVD) is investigated in the time and frequency domains. It is shown that the frequency dispersion of the complex capacitance of BSTO thin films can be understood in terms of a power-law frequency dependence from 1mHz to 20GHz. From the correspondence between the time and frequency domain measurements, it is concluded that the power-law relaxation currents extend back to the nano second regime of DRAM operation. The temperature, field, and annealing dependence of the dielectric relaxation currents are also investigated and mechanisms for the observed power law relaxation are explored. An equivalent circuit model of a high dielectric constant thin film capacitor is developed based on the electrical measurements and implemented in PSPICE. Excellent agreement is found between the experimental and simulated electrical characteristics showing the utility of the equivalent circuit model in simulating the electrical properties of high dielectric constant thin films. Using the equivalent circuit model, it is shown that the greatest charge loss due to dielectric relaxation occurs during the first read after a refresh time following a write to the opposite logic state for a capacitor that has been written to the same logic state for a long time (opposite state write charge loss). A theoretical closed form expression that is a function of three material parameters is developed which estimates the opposite state write charge loss due to dielectric relaxation. Using the closed form

Chromite/titanate based perovskites for application as anodes in solid oxide fuel cells

NARCIS (Netherlands)

Pudmich, G.; Boukamp, Bernard A.; Gonzalez Cuenca, M.M.; Jungen, W.; Zipprich, W.M.; Tietz, F.

2000-01-01

Perovskites containing lanthanides, partially substituted by alkaline-earth elements and transition metals like Cr, Ti, Fe or Co show a very broad range of physical properties. Therefore several perovskite materials, based on lanthanum chromite and strontium titanate were synthesised and

Synthesis and structural characterization of Ce-doped bismuth titanate

International Nuclear Information System (INIS)

Pavlovic, Nikolina; Srdic, Vladimir V.

2009-01-01

Ce-modified bismuth titanate nanopowders Bi 4-x Ce x Ti 3 O 12 (x ≤ 1) have been synthesized using a coprecipitation method. DTA/TG, FTIR, XRD, SEM/EDS and BET methods were used in order to investigate the effect of Ce-substitution on the structure, morphology and sinterability of the obtained powders. The phase structure investigation revealed that after calcinations at 600 deg. C powder without Ce addition exhibited pure bismuth titanate phase; however, powders with Ce (x = 0.25, 0.5 and 0.75) had bismuth titanate pyrochlore phase as the second phase. The strongest effect of Ce addition on the structure was noted for the powder with the highest amount of Ce (x = 1) having a cubic pyrochlore structure. The presence of pure pyrochlore phase was explained by its stabilization due to the incorporation of cerium ions in titanate structure. Ce-modified bismuth titanate ceramic had a density over 95% of theoretical density and the fracture in transgranular manner most probably due to preferable distribution of Ce in boundary region

Development, characterization and comparison of two strontium doped nano hydroxyapatite molecules for enamel repair/regeneration.

Science.gov (United States)

Krishnan, Vinod; Bhatia, Ankit; Varma, Harikrishna

2016-05-01

Enamel damage resulting or arising from/associated with orthodontic treatment such as white spot lesions and surface deterioration after debonding brackets along with incipient carious lesions are considered problems not amenable for routine restorations due to its invasive nature. The present study was aimed at synthesizing and characterizing nHAp and 25 and 50 mol% strontium nHAp as a surface application modality for dental enamel remineralization/repair. 25 and 50 mol% Sr nHAp was synthesized and characterized in comparison with custom made pure nHAp initially with the help of transmission and scanning electron microscopy as well as toxicological assessment. Further, comparative evaluation of these novel synthesized strontium substituted particles was assessed for its efficacy in repairing damaged enamel with the help of atomic force microscopy, scanning electron microscopy and micro indentation testing. There is increase in crystallinity and reduced particle size favoring dissolution and re-precipitation through small incipient carious lesions and soft white spot areas with 25% Sr-nHAp. Sr doped specimens showed more cell viability in comparison with pure nHAP make it less cytotoxic and hence a biologically friendly material which can be safely applied in patient's mouth. AFM images obtained from 25% and 50% Sr nHAp treated specimens clearly indicated increased roughness in surface topography and performed well with micro indentation test. The novel synthesized Sr doped nHAp forms an improved treatment modality to tackle the long standing quest for solving the problem of enamel loss with incipient carious lesions and WSL from orthodontic procedures. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

TAILORING INORGANIC SORBENTS FOR SRS STRONTIUM AND ACTINIDE SEPARATIONS: OPTIMIZED MONOSODIUM TITANATE PHASE II FINAL REPORT

International Nuclear Information System (INIS)

Hobbs, D; Thomas Peters, T; Michael Poirier, M; Mark Barnes, M; Major Thompson, M; Samuel Fink, S

2007-01-01

This document provides a final report of Phase II testing activities for the development of a modified monosodium titanate (MST) that exhibits improved strontium and actinide removal characteristics compared to the baseline MST material. The activities included determining the key synthesis conditions for preparation of the modified MST, preparation of the modified MST at a larger scale by a commercial vendor, demonstration of the strontium and actinide removal characteristics with actual tank waste supernate and measurement of filtration characteristics. Key findings and conclusions include the following. Testing evaluated three synthetic methods and eleven process parameters for the optimum synthesis conditions for the preparation on an improved form of MST. We selected the post synthesis method (Method 3) for continued development based on overall sorbate removal performance. We successfully prepared three batches of the modified MST using Method 3 procedure at a 25-gram scale. The laboratory prepared modified MST exhibited increased sorption kinetics with simulated and actual waste solutions and similar filtration characteristics to the baseline MST. Characterization of the modified MST indicated that the post synthesis treatment did not significantly alter the particle size distribution, but did significantly increase the surface area and porosity compared to the original MST. Testing indicated that the modified MST exhibits reduced affinity for uranium compared to the baseline MST, reducing risk of fissile loading. Shelf-life testing indicated no change in strontium and actinide performance removal after storing the modified MST for 12-months at ambient laboratory temperature. The material releases oxygen during the synthesis and continues to offgas after the synthesis at a rapidly diminishing rate until below a measurable rate after 4 months. Optima Chemical Group LLC prepared a 15-kilogram batch of the modified MST using the post synthesis procedure (Method

Barium titanate thick films prepared by screen printing technique

Directory of Open Access Journals (Sweden)

Mirjana M. Vijatović

2010-06-01

Full Text Available The barium titanate (BaTiO3 thick films were prepared by screen printing technique using powders obtained by soft chemical route, modified Pechini process. Three different barium titanate powders were prepared: i pure, ii doped with lanthanum and iii doped with antimony. Pastes for screen printing were prepared using previously obtained powders. The thick films were deposited onto Al2O3 substrates and fired at 850°C together with electrode material (silver/palladium in the moving belt furnace in the air atmosphere. Measurements of thickness and roughness of barium titanate thick films were performed. The electrical properties of thick films such as dielectric constant, dielectric losses, Curie temperature, hysteresis loop were reported. The influence of different factors on electrical properties values was analyzed.

Application of La-Doped SrTiO3 in Advanced Metal-Supported Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Sabrina Presto

2018-03-01

Full Text Available Composite materials frequently allow the drawbacks of single components to be overcome thanks to a synergistic combination of material- and structure-specific features, leading to enhanced and also new properties. This is the case of a metallic-ceramic composite, a nickel-chromium-aluminum (NiCrAl foam impregnated with La-doped Strontium Titanate (LST. This particular cermet has very interesting properties that can be used in different fields of application, namely: mechanical robustness provided by the metal foam; and chemical stability in harsh conditions of temperature and atmosphere by promotion of a thin protective layer of alumina (Al2O3; high electronic conductivity given by a percolating ceramic conducting phase, i.e., La-doped Strontium Titanate. In this paper, its application as a current collector in a metal-supported Solid Oxide Fuel Cells (SOFC was studied. Firstly, the electronic properties of different compositions, stoichiometric and under stoichiometric, of LST were analyzed to choose the best one in terms of conductivity and phase purity. Then, LST chemical stability was studied in the presence of Al2O3 at different temperatures, gas compositions and aging times. Finally, stability and conductivity of LST-impregnated NiCrAl foam composite materials were measured, and LST was found to be fully compatible with the NiCrAl foam, as no reactions were detected in oxidizing and reducing atmosphere after up to 300 h operation at 750 °C and 900 °C between the Al2O3 layer and LST. Results showed that the composite is suitable as a current collector in innovative designs of metal-supported SOFC, like the Evolve cell, in which the metallic part is supposed not only to provide the structural stability to the cell, but also to play the role of current collector due to the impregnation of ceramic material.

Digital to analog resistive switching transition induced by graphene buffer layer in strontium titanate based devices.

Science.gov (United States)

Wan, Tao; Qu, Bo; Du, Haiwei; Lin, Xi; Lin, Qianru; Wang, Da-Wei; Cazorla, Claudio; Li, Sean; Liu, Sidong; Chu, Dewei

2018-02-15

Resistive switching behaviour can be classified into digital and analog switching based on its abrupt and gradual resistance change characteristics. Realizing the transition from digital to analog switching in the same device is essential for understanding and controlling the performance of the devices with various switching mechanisms. Here, we investigate the resistive switching in a device made with strontium titanate (SrTiO 3 ) nanoparticles using X-ray diffractometry, scanning electron microscopy, Raman spectroscopy, and direct electrical measurements. It is found that the well-known rupture/formation of Ag filaments is responsible for the digital switching in the device with Ag as the top electrode. To modulate the switching performance, we insert a reduced graphene oxide layer between SrTiO 3 and the bottom FTO electrode owing to its good barrier property for the diffusion of Ag ions and high out-of-plane resistance. In this case, resistive switching is changed from digital to analog as determined by the modulation of interfacial resistance under applied voltage. Based on that controllable resistance, potentiation and depression behaviours are implemented as well. This study opens up new ways for the design of multifunctional devices which are promising for memory and neuromorphic computing applications. Copyright © 2017 Elsevier Inc. All rights reserved.

Investigation of the effect of temperature on aging behavior of Fe-doped lead zirconate titanate

Science.gov (United States)

Promsawat, Napatporn; Promsawat, Methee; Janphuang, Pattanaphong; Marungsri, Boonruang; Luo, Zhenhua; Pojprapai, Soodkhet

The aging degradation behavior of Fe-doped Lead zirconate titanate (PZT) subjected to different heat-treated temperatures was investigated over 1000h. The aging degradation in the piezoelectric properties of PZT was indicated by the decrease in piezoelectric charge coefficient, electric field-induced strain and remanent polarization. It was found that the aging degradation became more pronounced at temperature above 50% of the PZT’s Curie temperature. A mathematical model based on the linear logarithmic stretched exponential function was applied to explain the aging behavior. A qualitative aging model based on polar macrodomain switchability was proposed.

Sintering and Electrical Characterization of La and Nb Co‐doped SrTiO3 Electrode Materials for Solid Oxide Cell Applications

DEFF Research Database (Denmark)

Sudireddy, Bhaskar Reddy; Agersted, Karsten

2014-01-01

Single‐phase lanthanum and niobium co‐doped strontium titanate (Sr1–3x/2LaxTi0.9Nb0.1O3; x = 0–0.02) ceramics were prepared. Dilatometry in reducing atmosphere showed an increase in the sintering rate and sintered density with an increase in La amount. Microscopy of fractured surfaces of sintered...... samples showed that the average grain size increased drastically in reducing conditions with increasing La content (and associated A‐site vacancies). By incorporating 2 mol.% La, the electronic conductivity significantly improved from 80 to 135 S cm−1 at 1,000 °C, and even larger improvements were...... observed at lower temperatures. These observations demonstrate the flexibility in tailoring the microstructure and electronic transport properties by doping small amounts of La into the Nb‐doped SrTiO3 and show that Sr1–3x/2LaxTi0.9Nb0.1O3 is a potential electrode material for solid oxide cells....

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

The effect of temperature on polarization reversal of strontium-doped lead zirconate titanate ceramics was studied. The piezoelectric properties viz. dielectric constant and piezoelectric coupling coefficient, were used for polarization reversal characteristic. These properties and apparent coercive field weremeasured during ...

Tunable dielectric properties of Barium Magnesium Niobate (BMN) doped Barium Strontium Titanate (BST) thin films by magnetron sputtering

Science.gov (United States)

Alema, Fikadu; Reinholz, Aaron; Pokhodnya, Konstantin

2013-03-01

We report on the tunable dielectric properties of Mg and Nb co-doped Ba0.45Sr0.55TiO3 (BST) thin film prepared by the magnetron sputtering using BST target (pure and doped with BaMg0.33Nb0.67O3 (BMN)) on Pt/TiO2/SiO2/Al2O3 4'' wafers at 700 °C under oxygen atmosphere. The electrical measurements are conducted on 2432 metal-ferroelectric-metal capacitors using Pt as the top and bottom electrode. The crystalline structure, microstructure, and surface morphology of the films are analyzed and correlated to the films dielectric properties. The BMN doped and undoped BST films have shown tunabilities of 48% and 52%; and leakage current densities of 2.2x10-6 A/cm2 and 3.7x10-5 A/cm2, respectively at 0.5 MV/cm bias field. The results indicate that the BMN doped film exhibits a lower leakage current with no significant decrease in tunability. Due to similar electronegativity and ionic radii, it was suggested that both Mg2+ (accepter-type) and Nb5+ (donor-type) dopants substitutTi4+ ion in BST. The improvement in the film dielectric losses and leakage current with insignificant loss of tunability is attributed to the adversary effects of Mg2+ and Nb5+ in BST.

Gelcasting of strontium doped lanthanum manganite for solid oxide fuel cell applications

International Nuclear Information System (INIS)

Abdul Haleem, B.; Bhuvana, R.; Udayakumar, A.

2009-01-01

Solid oxide fuel cells (SOFCs) are devices that offer high efficiency power output with negligible emissions. Cathode supported tubular SOFCs consist of porous cathode tubes made up of strontium doped lanthanum manganite, La 1-x Sr x MnO 3 (LSM) that work as functional component as well as structural support for the rest of the cell components. Gelcasting is one of the most suitable methods for the fabrication of porous ceramics. This paper describes the fabrication of porous LSM cathode by gelcasting process. Gelcasting parameters such as monomer concentration, powder volume fraction, pH of the slurry, etc were optimized. Slow drying of green specimens minimized warpage and cracking. Sintered specimens with controlled porosity were obtained by the use of suitable pore-forming agents. The coefficient of thermal expansion (CTE) of sintered specimens was measured, which was found matching with the CTE values of cell components reported in the literature. These results have shown the suitability of the gelcast generated LSM cathodes for SOFC applications. (author)

Study on the Key Technology of High Purity Strontium Titanate Powder Synthesized from Oxalic Acid Co-sediment Precipitation

Science.gov (United States)

Bi, Xiaoguo; Dong, Yingnan; Li, Yingjie; Niu, Wei; Tang, Jian; Ding, Shuang; Li, Meiyang

2017-09-01

Oxalate coprecipitation is applied in this paper, high purity titanium tetrachloride, and after the purification of strontium chloride, match with a certain concentration of solution, oxalate and strontium chloride and titanium tetrachloride in 1.005:1.000 make strontium titanium mixture ratio, slowly under 60°C to join in oxalic acid solution, aging around 4 h, get oxygen titanium strontium oxalate (SrTiO(C2O4)2 • 4H2 ) precipitation, after washing, drying and other process made oxygen titanium strontium oxalate powder.

Fabrication and properties of yttrium doped barium titanate film by RF sputtering

International Nuclear Information System (INIS)

Igarashi, H.; Yuasa, M.; Okazaki, K.

1985-01-01

Semiconductive barium titanate films were fabricated by RF sputtering on fused quartz, alumina and barium titanate ceramic substrates using barium titanate ceramic with a small amount of yttria as a target. The films on the barium titanate substrates turned blue color and showed a small PTC effect by heat-treating at 1000 0 C in the air after deposition at the substrate temperature of 600 0 C

Bright white upconversion luminescence from Er3+/Tm3+/Yb3+-doped titanate-based glasses prepared by aerodynamic levitation method

Science.gov (United States)

Zhang, Minghui; Yu, Jianding; Jiang, Wan; Liu, Yan; Ai, Fei; Wen, Haiqin; Jiang, Meng; Yu, Huimei; Pan, Xiuhong; Tang, Meibo; Gai, Lijun

2017-10-01

Aerodynamic levitation method was employed to prepare Er3+/Tm3+/Yb3+-doped titanate-based glasses. DTA results show that the glass performs high thermal stability with the glass transition temperature of 799 °C. The interaction among rare earth ions has been discussed by adjusting the relative concentration. Er3+ ions can quench the upconversion luminescence of Tm3+ ions. Tm3+ ions play a strong role in quenching the emissions of Er3+ and Tm3+ when the content of Tm3+ ions is greater than or equal 0.05. From the view of the ratio of red emission to green emission, Tm3+ ions can improve the red emission of Er3+ ions to some extent in contrast with the green emissions of Er3+ ions. 980 nm incident laser can be efficiently absorbed by Yb3+ ions. The relative intensity of red, green, and blue upconversion luminescence has been tuned to obtain white light. The composition with white upconversion luminescence of the color coordinate (0.291, 0.3292) has been found. Moreover, white upconversion luminescence mechanism is a two-photon process of ET, ESA, and cooperative sensitization. Rare earth ions doped titanate-based glasses with bright upconversion luminescence perform potential applications in color display, back light, et al.

Microstructure evolution and electrical characterization of Lanthanum doped Barium Titanate (BaTiO_3) ceramics

International Nuclear Information System (INIS)

Billah, Masum; Ahmed, A.; Rahman, Md. Miftaur; Mahbub, Rubbayat; Gafur, M. A.; Bashar, M. Shahriar

2016-01-01

In the current work, we investigated the structural and dielectric properties of Lanthanum oxide (La_2O_3) doped Barium Titanate (BaTiO_3) ceramics and established a correlation between them. Solid state sintering method was used to dope BaTiO_3 with 0.3, 0.5 and 0.7 mole% La_2O_3 under different sintering parameters. The raw materials used were La_2O_3 nano powder of ~80 nm grain size and 99.995% purity and BaTiO_3 nano powder of 100 nm grain size and 99.99% purity. Grain size distribution and morphology of fracture surface of sintered pellets were examined by Field Emission Scanning Electron Microscope and X-Ray Diffraction analysis was conducted to confirm the formation of desired crystal structure. The research result reveal that grain size and electrical properties of BaTiO_3 ceramic significantly enhanced for small amount of doping (up to 0.5 mole% La_2O_3) and then decreased with increasing doping concentration. Desired grain growth (0.80-1.3 µm) and high densification (<90% theoretical density) were found by proper combination of temperature, sintering parameters and doping concentration. We found the resultant stable value of dielectric constant was 10000-12000 at 100-300 Hz in the temperature range of 30°-50° C for 0.5 mole% La_2O_3 with corresponding shift of curie temperature around 30° C. So overall this research showed that proper La"3"+ concentration can control the grain size, increase density, lower curie temperature and hence significantly improve the electrical properties of BaTiO_3 ceramics.

Simultaneous removal of Cr(VI) and 4-chlorophenol through photocatalysis by a novel anatase/titanate nanosheet composite: Synergetic promotion effect and autosynchronous doping

International Nuclear Information System (INIS)

Liu, Wen; Sun, Weiling; Borthwick, Alistair G.L.; Wang, Ting; Li, Fan; Guan, Yidong

2016-01-01

Highlights: • TNS composed of anatase and titanate synthesized via a facile one-step method. • Cr(VI) and 4-CP can be simultaneously removed by TNS through photocatalysis. • Photocatalytic efficiencies of Cr(VI) and 4-CP greatly enhanced when coexisting. • Synergetic promotion effect occurs due to separation of electron-hole pairs. • Autosynchronous doping after Cr(III) adsorption leads to narrowed energy gap. - Abstract: Clean-up of wastewaters with coexisting heavy metals and organic contaminants is a huge issue worldwide. In this study, a novel anatase/titanate nanosheet composite material (labeled as TNS) synthesized through a one-step hydrothermal reaction was demonstrated to achieve the goal of simultaneous removal of Cr(VI) and 4-cholophenol (4-CP) from water. TEM and XRD analyses indicated the TNS was a nano-composite of anatase and titanate, with anatase acting as the primary photocatalysis center and titanate as the main adsorption site. Enhanced photocatalytic removal of co-existent Cr(VI) and 4-CP was observed in binary systems, with apparent rate constants (k_1) for photocatalytic reactions of Cr(VI) and 4-CP about 3.1 and 2.6 times of that for single systems. In addition, over 99% of Cr(VI) and 4-CP was removed within 120 min through photocatalysis by TNS at pH 7 in the binary system. Mechanisms for enhanced photocatalytic efficiency in the binary system are identified as: (1) a synergetic effect on the photo-reduction of Cr(VI) and photo-oxidation of 4-CP due to efficient separation of electron-hole pairs, and (2) autosynchronous doping because of reduced Cr(III) adsorption onto TNS. Furthermore, TNS could be efficiently reused after a simple acid-base treatment.

Simultaneous removal of Cr(VI) and 4-chlorophenol through photocatalysis by a novel anatase/titanate nanosheet composite: Synergetic promotion effect and autosynchronous doping

Energy Technology Data Exchange (ETDEWEB)

Liu, Wen, E-mail: wzl0025@auburn.edu [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Science and Engineering, Nanjing University of Information Science and Technology, Nanjing 210044 (China); The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States); Sun, Weiling [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Borthwick, Alistair G.L. [School of Engineering, The University of Edinburgh, The King’s Buildings, Edinburgh EH9 3JL (United Kingdom); Wang, Ting [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, Department of Environmental Engineering, Peking University, Beijing 100871 (China); Li, Fan [Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States); Guan, Yidong, E-mail: yidongguan@nuist.edu.cn [Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control, School of Environmental Science and Engineering, Nanjing University of Information Science and Technology, Nanjing 210044 (China); Environmental Engineering Program, Department of Civil Engineering, Auburn University, Auburn, AL 36849 (United States)

2016-11-05

Highlights: • TNS composed of anatase and titanate synthesized via a facile one-step method. • Cr(VI) and 4-CP can be simultaneously removed by TNS through photocatalysis. • Photocatalytic efficiencies of Cr(VI) and 4-CP greatly enhanced when coexisting. • Synergetic promotion effect occurs due to separation of electron-hole pairs. • Autosynchronous doping after Cr(III) adsorption leads to narrowed energy gap. - Abstract: Clean-up of wastewaters with coexisting heavy metals and organic contaminants is a huge issue worldwide. In this study, a novel anatase/titanate nanosheet composite material (labeled as TNS) synthesized through a one-step hydrothermal reaction was demonstrated to achieve the goal of simultaneous removal of Cr(VI) and 4-cholophenol (4-CP) from water. TEM and XRD analyses indicated the TNS was a nano-composite of anatase and titanate, with anatase acting as the primary photocatalysis center and titanate as the main adsorption site. Enhanced photocatalytic removal of co-existent Cr(VI) and 4-CP was observed in binary systems, with apparent rate constants (k{sub 1}) for photocatalytic reactions of Cr(VI) and 4-CP about 3.1 and 2.6 times of that for single systems. In addition, over 99% of Cr(VI) and 4-CP was removed within 120 min through photocatalysis by TNS at pH 7 in the binary system. Mechanisms for enhanced photocatalytic efficiency in the binary system are identified as: (1) a synergetic effect on the photo-reduction of Cr(VI) and photo-oxidation of 4-CP due to efficient separation of electron-hole pairs, and (2) autosynchronous doping because of reduced Cr(III) adsorption onto TNS. Furthermore, TNS could be efficiently reused after a simple acid-base treatment.

Influence of single and binary doping of strontium and lithium on in vivo biological properties of bioactive glass scaffolds

Science.gov (United States)

Khan, Pintu Kumar; Mahato, Arnab; Kundu, Biswanath; Nandi, Samit K.; Mukherjee, Prasenjit; Datta, Someswar; Sarkar, Soumya; Mukherjee, Jayanta; Nath, Shalini; Balla, Vamsi K.; Mandal, Chitra

2016-01-01

Effects of strontium and lithium ion doping on the biological properties of bioactive glass (BAG) porous scaffolds have been checked in vitro and in vivo. BAG scaffolds were prepared by conventional glass melting route and subsequently, scaffolds were produced by evaporation of fugitive pore formers. After thorough physico-chemical and in vitro cell characterization, scaffolds were used for pre-clinical study. Soft and hard tissue formation in a rabbit femoral defect model after 2 and 4 months, were assessed using different tools. Histological observations showed excellent osseous tissue formation in Sr and Li + Sr scaffolds and moderate bone regeneration in Li scaffolds. Fluorochrome labeling studies showed wide regions of new bone formation in Sr and Li + Sr doped samples as compared to Li doped samples. SEM revealed abundant collagenous network and minimal or no interfacial gap between bone and implant in Sr and Li + Sr doped samples compared to Li doped samples. Micro CT of Li + Sr samples showed highest degree of peripheral cancellous tissue formation on periphery and cortical tissues inside implanted samples and vascularity among four compositions. Our findings suggest that addition of Sr and/or Li alters physico-chemical properties of BAG and promotes early stage in vivo osseointegration and bone remodeling that may offer new insight in bone tissue engineering. PMID:27604654

Remarkable Strontium B-Site Occupancy in FerroelectricPb(Zr1-xTix)O3 Solid Solutions Doped with Cryolite-Type StrontiumNiobate

Energy Technology Data Exchange (ETDEWEB)

Feltz, A.; Schmidt-Winkel, P.; Schossman, M.; Booth, C.H.; Albering, J.

2007-04-26

New high-performance ferroelectric materials based on Pb(Zr{sub 1-x}Ti{sub x})O{sub 3} (PZT) that are doped with cryolite-type strontium niobate (SNO, Sr{sub 4}(Sr{sub 2-2y/3}Nb{sub 2+2y/3})O{sub 11+y}V{sub 0,1-y} with 0 {le} y {le} 1), hence denoted PZT:SNO, and their microscopic structure are described. The combination of exceptional piezoelectric properties, i.e. a piezoelectric strain constant of d{sub 33} {approx} 760 pm/V, with excellent stability and degradation resistance makes ferroelectric PZT:SNO solid solutions very attractive for use in novel and innovative piezoelectric actuator and transducer applications. Extended X-ray absorption fine-structure (EXAFS) analyses of PZT:SNO samples revealed that {approx}10 % of the Sr cations occupy the nominal B-sites of the perovskite-type PZT host lattice. This result was supported by EXAFS analyses of both a canonical SrTiO{sub 3} perovskite and two SNO model and reference compounds. Fit models that do not account for Sr cations on B-sites were ruled out. A clear Sr-Pb peak in Fourier transformed EXAFS data visually confirmed this structural model. The generation of temporary oxygen vacancies and the intricate defect chemistry induced by SNO-doping of PZT are crucial for the exceptional materials properties exhibited by PZT:SNO materials.

Investigation of Voltage-Activated BAW Devices and Filters

Science.gov (United States)

2016-09-04

strontium titanate (STO) and barium-strontium titanate (BST), with the ultimate objective of creating high- performance, reconfigurable filters and...induced piezoelectricity in thin-film strontium titanate (STO) and barium-strontium titanate (BST), with the ultimate objective of creating high...this work 1. The effect of patterned vs. unpatterned acoustic Bragg reflector on barium strontium titanate solidly mounted resonator. Authors: George

A comparison study of rhodamine B photodegradation over nitrogen-doped lamellar niobic acid and titanic acid under visible-light irradiation.

Science.gov (United States)

Li, Xiukai; Kikugawa, Naoki; Ye, Jinhua

2009-01-01

A solid-state reaction method with urea as a nitrogen precursor was used to prepare nitrogen-doped lamellar niobic and titanic solid acids (i.e., HNb(3)O(8) and H(2)Ti(4)O(9)) with different acidities for visible-light photocatalysis. The photocatalytic activities of the nitrogen-doped solid acids were evaluated for rhodamine B (RhB) degradation and the results were compared with those obtained over the corresponding nitrogen-doped potassium salts. Techniques such as XRD, BET, SEM, X-ray photoelectron spectroscopy, and UV-visible diffuse reflectance spectroscopy were adopted to explore the nature of the materials as well as the characteristics of the doped nitrogen species. It was found that the intercalation of the urea precursor helped to stabilize the layered structures of both lamellar solid acids and enabled easier nitrogen doping. The effects of urea intercalation were more significant for the more acidic HNb(3)O(8) sample than for the less acidic H(2)Ti(4)O(9). Compared with the nitrogen-doped KNb(3)O(8) and K(2)Ti(4)O(9) samples, the nitrogen-doped HNb(3)O(8) and H(2)Ti(4)O(9) solid acids absorb more visible light and exhibit a superior activity for RhB photodegradation under visible-light irradiation. The nitrogen-doped HNb(3)O(8) sample performed the best among all the samples. The results of the current study suggest that the protonic acidity of the lamellar solid-acid sample is a key factor that influences nitrogen doping and the resultant visible-light photocatalysis.

Strontium-doped hematite as a possible humidity sensing material for soil water content determination.

Science.gov (United States)

Tulliani, Jean-Marc; Baroni, Chiara; Zavattaro, Laura; Grignani, Carlo

2013-09-10

The aim of this work is to study the sensing behavior of Sr-doped hematite for soil water content measurement. The material was prepared by solid state reaction from commercial hematite and strontium carbonate heat treated at 900 °C. X-Ray diffraction, scanning electron microscopy and mercury intrusion porosimetry were used for microstructural characterization of the synthesized powder. Sensors were then prepared by uniaxially pressing and by screen-printing, on an alumina substrate, the prepared powder and subsequent firing in the 800-1,000 °C range. These sensors were first tested in a laboratory apparatus under humid air and then in an homogenized soil and finally in field. The results evidenced that the screen printed film was able to give a response for a soil matric potential from about 570 kPa, that is to say well below the wilting point in the used soil.

Strontium-Doped Hematite as a Possible Humidity Sensing Material for Soil Water Content Determination

Directory of Open Access Journals (Sweden)

Carlo Grignani

2013-09-01

Full Text Available The aim of this work is to study the sensing behavior of Sr-doped hematite for soil water content measurement. The material was prepared by solid state reaction from commercial hematite and strontium carbonate heat treated at 900 °C. X-Ray diffraction, scanning electron microscopy and mercury intrusion porosimetry were used for microstructural characterization of the synthesized powder. Sensors were then prepared by uniaxially pressing and by screen-printing, on an alumina substrate, the prepared powder and subsequent firing in the 800–1,000 °C range. These sensors were first tested in a laboratory apparatus under humid air and then in an homogenized soil and finally in field. The results evidenced that the screen printed film was able to give a response for a soil matric potential from about 570 kPa, that is to say well below the wilting point in the used soil.

Enhanced magnetic separation and photocatalytic activity of nitrogen doped titania photocatalyst supported on strontium ferrite.

Science.gov (United States)

Abd Aziz, Azrina; Yong, Kok Soon; Ibrahim, Shaliza; Pichiah, Saravanan

2012-01-15

An enhanced ferromagnetic property, visible light active TiO(2) photocatalyst was successfully synthesized by supporting strontium ferrite (SrFe(12)O(19)) onto TiO(2) doped with nitrogen (N) and compared with N-doped TiO(2). The synthesized catalysts were further characterized with X-ray diffraction (XRD), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDS), BET surface area analysis, vibrating sample magnetometer (VSM), X-ray photon spectroscopy (XPS) and visible light spectroscopy analysis for their respective properties. The XRD and EDS revealed the structural and inorganic composition of N-TiO(2) supported on SrFe(12)O(19). The supported N-TiO(2) exhibited a strong ferromagnetic property with tremendous stability against magnetic property losses. It also resulted in reduced band gap (2.8 eV) and better visible light absorption between 400 and 800 nm compared to N-doped TiO(2). The photocatalytic activity was investigated with a recalcitrant phenolic compound namely 2,4-dichlorophenol (2,4-DCP) as a model pollutant under direct bright and diffuse sunlight exposure. A complete degradation of 2,4-DCP was achieved with an initial concentration of 50mg/L for both photocatalysts in 180 min and 270 min respectively under bright sunlight. Similarly the diffuse sunlight study resulted in complete degradation for supported N-TiO(2) and >85% degradation N-TiO(2), respectively. Finally the supported photocatalyst was separated under permanent magnetic field with a mass recovery ≈ 98% for further reuse. Copyright © 2011 Elsevier B.V. All rights reserved.

Unexpectedly high piezoelectricity of Sm-doped lead zirconate titanate in the Curie point region.

Science.gov (United States)

Seshadri, Shruti B; Nolan, Michelle M; Tutuncu, Goknur; Forrester, Jennifer S; Sapper, Eva; Esteves, Giovanni; Granzow, Torsten; Thomas, Pam A; Nino, Juan C; Rojac, Tadej; Jones, Jacob L

2018-03-07

Large piezoelectric coefficients in polycrystalline lead zirconate titanate (PZT) are traditionally achieved through compositional design using a combination of chemical substitution with a donor dopant and adjustment of the zirconium to titanium compositional ratio to meet the morphotropic phase boundary (MPB). In this work, a different route to large piezoelectricity is demonstrated. Results reveal unexpectedly high piezoelectric coefficients at elevated temperatures and compositions far from the MPB. At temperatures near the Curie point, doping with 2 at% Sm results in exceptionally large piezoelectric coefficients of up to 915 pm/V. This value is approximately twice those of other donor dopants (e.g., 477 pm/V for Nb and 435 pm/V for La). Structural changes during the phase transitions of Sm-doped PZT show a pseudo-cubic phase forming ≈50 °C below the Curie temperature. Possible origins of these effects are discussed and the high piezoelectricity is posited to be due to extrinsic effects. The enhancement of the mechanism at elevated temperatures is attributed to the coexistence of tetragonal and pseudo-cubic phases, which enables strain accommodation during electromechanical deformation and interphase boundary motion. This work provides insight into possible routes for designing high performance piezoelectrics which are alternatives to traditional methods relying on MPB compositions.

Microstructure evolution and electrical characterization of Lanthanum doped Barium Titanate (BaTiO{sub 3}) ceramics

Energy Technology Data Exchange (ETDEWEB)

Billah, Masum, E-mail: masum.buet09@gmail.com; Ahmed, A., E-mail: jhinukbuetmme@gmail.com; Rahman, Md. Miftaur, E-mail: miftaurrahman@mme.buet.ac.bd [Department of Materials & Metallurgical Engineering, Bangladesh University of Engineering and Technology, Dhaka-1000 (Bangladesh); Mahbub, Rubbayat, E-mail: rubayyatm@gce.buet.ac.bd [Department of Glass and Ceramic Engineering, Bangladesh University of Engineering and Technology, Dhaka-1000 (Bangladesh); Gafur, M. A., E-mail: d-r-magafur@bcsir.gov.bd [Bangladesh Council of Scientific & Industrial Research (BCSIR), Dhaka-1205 (Bangladesh); Bashar, M. Shahriar, E-mail: bashar@agni.com [Institute of Fuel Research & Development, Bangladesh Council of Scientific & Industrial Research (BCSIR), Dhaka-1205 (Bangladesh)

2016-07-12

In the current work, we investigated the structural and dielectric properties of Lanthanum oxide (La{sub 2}O{sub 3}) doped Barium Titanate (BaTiO{sub 3}) ceramics and established a correlation between them. Solid state sintering method was used to dope BaTiO{sub 3} with 0.3, 0.5 and 0.7 mole% La{sub 2}O{sub 3} under different sintering parameters. The raw materials used were La{sub 2}O{sub 3} nano powder of ~80 nm grain size and 99.995% purity and BaTiO{sub 3} nano powder of 100 nm grain size and 99.99% purity. Grain size distribution and morphology of fracture surface of sintered pellets were examined by Field Emission Scanning Electron Microscope and X-Ray Diffraction analysis was conducted to confirm the formation of desired crystal structure. The research result reveal that grain size and electrical properties of BaTiO{sub 3} ceramic significantly enhanced for small amount of doping (up to 0.5 mole% La{sub 2}O{sub 3}) and then decreased with increasing doping concentration. Desired grain growth (0.80-1.3 µm) and high densification (<90% theoretical density) were found by proper combination of temperature, sintering parameters and doping concentration. We found the resultant stable value of dielectric constant was 10000-12000 at 100-300 Hz in the temperature range of 30°-50° C for 0.5 mole% La{sub 2}O{sub 3} with corresponding shift of curie temperature around 30° C. So overall this research showed that proper La{sup 3+} concentration can control the grain size, increase density, lower curie temperature and hence significantly improve the electrical properties of BaTiO{sub 3} ceramics.

Characterization and Mineralization of Strontium Doped Nano Hydroxyapatite Coating on Titanium Rods

Directory of Open Access Journals (Sweden)

Chuang WANG

2017-08-01

Full Text Available Pure nano hydroxyapatite (nHA and strontium doped nano hydroxyapatite (Sr-nHA, Sr/(Ca+Sr =10% were prepared by a one-step method which mainly used the principle of homogeneous phase co-precipitation. Fourier transform infrared spectroscopy (FT-IR revealed that the intensity of absorption was decreased with Sr doping. X-ray diffraction (XRD showed that special peak position of Sr-nHA shifted to a smaller 2θ angle compared with the pure nHA. Both the pure nHA (39.46±11.19nm in length and 15.90±3.65 nm in width and Sr-nHA (32.95±10.21 nm in length and 13.18±3.18 nm in width samples showed a tiny nano-rod feature. Moreover, Tc4 (Ti-6Al-4V rods (1 mm in diameter and 20 mm in length coated with pure nHA or Sr-nHA were prepared by high-energy plasma spraying. Elements of calcium (Ca, phosphorus (P, oxygen (O and Sr were detected on the Sr-nHA coating surface by Energy Dispersive Spectrometry (EDS. XRD result also indicates the chemical composition almost did not change significantly after spraying. By immersion in the simulated body fluid (SBF, in vitro mineralization ability was estimated and the superficial coats were evaluated by scanning electron microscopy (SEM and XRD. The results showed that Sr-nHA spraying surface has a better mineralization ability than the pure nHA coating. Therefore, the synthesized Sr-nHA would have potential for biological prostheses and other implantable materials.DOI: http://dx.doi.org/10.5755/j01.ms.23.3.17254

High temperature thermoelectric properties of strontium titanate thin films with oxygen vacancy and niobium doping

KAUST Repository

Sarath Kumar, S. R.; Barasheed, Abeer Z.; Alshareef, Husam N.

2013-01-01

We report the evolution of high temperature thermoelectric properties of SrTiO3 thin films doped with Nb and oxygen vacancies. Structure-property relations in this important thermoelectric oxide are elucidated and the variation of transport properties with dopant concentrations is discussed. Oxygen vacancies are incorporated during growth or annealing in Ar/H2 above 800 K. An increase in lattice constant due to the inclusion of Nb and oxygen vacancies is found to result in an increase in carrier density and electrical conductivity with simultaneous decrease in carrier effective mass and Seebeck coefficient. The lattice thermal conductivity at 300 K is found to be 2.22 W m-1 K-1, and the estimated figure of merit is 0.29 at 1000 K. © 2013 American Chemical Society.

High temperature thermoelectric properties of strontium titanate thin films with oxygen vacancy and niobium doping

KAUST Repository

Sarath Kumar, S. R.

2013-08-14

We report the evolution of high temperature thermoelectric properties of SrTiO3 thin films doped with Nb and oxygen vacancies. Structure-property relations in this important thermoelectric oxide are elucidated and the variation of transport properties with dopant concentrations is discussed. Oxygen vacancies are incorporated during growth or annealing in Ar/H2 above 800 K. An increase in lattice constant due to the inclusion of Nb and oxygen vacancies is found to result in an increase in carrier density and electrical conductivity with simultaneous decrease in carrier effective mass and Seebeck coefficient. The lattice thermal conductivity at 300 K is found to be 2.22 W m-1 K-1, and the estimated figure of merit is 0.29 at 1000 K. © 2013 American Chemical Society.

In situ Sn2+-incorporation synthesis of titanate nanotubes for photocatalytic dye degradation under visible light illumination

International Nuclear Information System (INIS)

Tsai, Chien-Cheng; Chen, Liang-Che; Yeh, Te-Fu; Teng, Hsisheng

2013-01-01

Highlights: ► Sn 2+ ions sensitize titanate nanotubes for photocatalysis under visible-light illumination. ► The Sn 5s orbital replaces the O 2p orbital as the top level of the valence band of titanates. ► The presence of Sn 2+ lifts the valence band of titanate nanotubes by approximately 0.9 eV. ► The doped Sn 2+ sites are active in donating photo-induced charges to dye degradation. - Abstract: Sn 2+ -incorporated titanate nanotubes, prepared by washing a layered sodium titanate with a SnCl 2 solution for tube formation, exhibit noticeable photocatalytic activity under visible light irradiation. This in situ synthesis results in a Sn/Ti ratio of approximately 0.6. Because of the introduction of Sn 2+ ions, the Sn 5s orbital replaces the O 2p orbital as the top level of the valence band of titanate nanotubes. Optical absorption analysis shows that Sn doping reduces the bandgap of titanate nanotubes from 3.5 to 2.6 eV. Oxidation of the Sn 2+ -incorporated titanate nanotubes leads to oxidation of Sn 2+ to Sn 4+ , hence, widening the bandgap. Under visible light irradiation, Sn 2+ -incorporated titanate nanotubes effectively degrade methylene blue in an aqueous solution, whereas the bare titanate nanotubes exhibit substantially lower photocatalytic activity. Photoluminescence analysis demonstrates that the induced charges from excitation of the Sn 2+ ions tend to be relaxed through chemical interactions, rather than irradiative recombination.

N Nwathore

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. N Nwathore. Articles written in Bulletin of Materials Science. Volume 34 Issue 1 February 2011 pp 129-132. Effect of temperature on polarization reversal of strontium-doped lead zirconate titanate (PSZT) ceramics · N Nwathore C M Lonkar D K Kharat · More Details Abstract ...

Strontium doped poly-ε-caprolactone composite scaffolds made by reactive foaming

Energy Technology Data Exchange (ETDEWEB)

Zehbe, Rolf, E-mail: zehbe@bls-germany.com [BLS Laboratories GmbH, Berlin (Germany); University of Potsdam, Institute of Physics and Astronomy, Potsdam (Germany); Zehbe, Kerstin [University of Potsdam, Department of Chemistry, Potsdam (Germany)

2016-10-01

In the reconstruction and regeneration of bone tissue, a primary goal is to initiate bone growth and to stabilize the surrounding bone. In this regard, a potentially useful component in biomaterials for bone tissue engineering is strontium, which acts as cationic active agent, triggering certain intracellular pathways and acting as so called dual action bone agent which inhibits bone resorption while stimulating bone regeneration. In this study we established a novel processing for the foaming of a polymer (poly-ε-caprolactone) and simultaneous chemical reaction of a mixture of calcium and strontium hydroxides to the respective carbonates using supercritical carbon dioxide. The resultant porous composite scaffold was optimized in composition and strontium content and was characterized via different spectroscopic (infrared and Raman spectroscopy, energy dispersive X-ray spectroscopy), imaging (SEM, μCT), mechanical testing and in vitro methods (fluorescence vital staining, MTT-assay). As a result, the composite scaffold showed good in vitro biocompatibility with partly open pore structure and the expected chemistry. First mechanical testing results indicate sufficient mechanical stability to support future in vivo applications. - Highlights: • Reactive foaming has been established for the synthesis of a PCL matrix with integrated strontium and calcium species • This material can potentially be useful in bone tissue engineering applications • Comparative in vitro cell culture experiments, imaging and spectroscopy analysis have been conducted.

Synthesis and characterization of strontium molybdate doped with copper, cobalt and zinc for purposes photocatalytic

International Nuclear Information System (INIS)

Dutra, F.B.; Silva, M.M.S.; Moriyama, A.L.L.; Souza, C.P.

2016-01-01

The broad concerns of contemporary society with environmental problems requires legislation and more effective techniques for wastewater treatment. In recent years, ceramic materials that have properties such as high melting points and high stability have been receiving great emphasis in several studies in particular heterogeneous photocatalysis, rapid and efficient method for the complete mineralization of contaminants. In this context, the present work deals with the synthesis and characterization of molybdate Strontium (SrMoO4) doped with copper, cobalt and zinc for the purpose of photocatalytic studies. The compounds were synthesized by complexation method EDTA / Citrate basic medium. The powders were characterized by Thermogravimetric Analysis (TG), X-Ray Diffraction (XRD), Particle size distribution by laser diffraction, Spectroscopy in the UV-Visible region, Energy Dispersive Spectroscopy (EDS) and Scanning Electron Microscopy (SEM), showing promising results as the crystalline phase of development and potential uses for the purpose of heterogeneous photocatalysis. (author)

Upconversion emission study of Er3+/Yb3+ doped barium titanate phosphor prepared by co-precipitation method

International Nuclear Information System (INIS)

Mahata, M.K.; Dey, R.; Kumar, K.; Rai, V.K.; Rai, S.B.

2012-01-01

In the present work we have successfully synthesized the Er 3+ , Yb 3+ doped barium titanate phosphor via co-precipitation synthesis method. Under 980 nm excitation, tri-color upconversion fluorescence has been observed. The Fourier Transform Infrared measurement was done to check the presence of organic impurities. In order to find out how many photons are involved in each emission band, the variation of UC emission intensity of the codoped phosphor is studied with increase in excitation power. Upconversion emission spectra show that as the annealing temperature of the powder is increased, intensity of red emission decreases and intensity of green emission increases due to the decrease in maximum phonon frequency of the host material. (author)

Defect Chemistry of a Zinc-Doped Lepidocrocite Titanate CsxTi2−x/2Znx/2O4 (x = 0.7) and its Protonic Form

DEFF Research Database (Denmark)

Gao, Tao; Fjellvåg, Helmer; Norby, Poul

2009-01-01

A zinc-doped layered titanate CsxTi2−x/2Znx/2O4 (x = 0.7) with lepidocrocite (γ-FeOOH)-type layered structure was prepared via solid-state calcination. A complete extraction of both lattice Zn atoms and interlayer Cs ions was observed upon acid exchange, producing a protonic form H2xTi2−x/2x/2O4·H2....... The protonic titanate H2xTi2−x/2x/2O4·H2O readily underwent delamination to produce its molecular single sheets Ti1−δδO24δ− (δ = 0.175) with distinctive two-dimensional morphology and small thickness (1 nm), suggesting promising applications in the assembly of functional nanostructures....

Strontium Titanate-based Composite Anodes for Solid Oxide Fuel Cells

DEFF Research Database (Denmark)

Blennow Tullmar, Peter; Kammer Hansen, Kent; Wallenberg, L.R.

2008-01-01

Surfactant-assisted infiltration of Gd-doped ceria (CGO) in Nb-doped SrTiO3 (STN) was investigated as a potential fuel electrode for solid oxide fuel cells (SOFC). An electronically conductive backbone structure of STN was first fabricated at high temperatures and then combined with the mixed con...

Barium iodide and strontium iodide crystals andd scintillators implementing the same

Science.gov (United States)

Payne, Stephen A; Cherepy, Nerine J; Hull, Giulia E; Drobshoff, Alexander D; Burger, Arnold

2013-11-12

In one embodiment, a material comprises a crystal comprising strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector according to another embodiment includes a scintillator optic comprising europium-doped strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector in yet another embodiment includes a scintillator optic comprising SrI.sub.2 and BaI.sub.2, wherein a ratio of SrI.sub.2 to BaI.sub.2 is in a range of between 0:1 A method for manufacturing a crystal suitable for use in a scintillator includes mixing strontium iodide-containing crystals with a source of Eu.sup.2+, heating the mixture above a melting point of the strontium iodide-containing crystals, and cooling the heated mixture near the seed crystal for growing a crystal. Additional materials, systems, and methods are presented.

Microstructure Changes of Aluminum Titanate Refractory Doped SiO{sub 2} and ZrO{sub 2} in Molten Steel

Energy Technology Data Exchange (ETDEWEB)

Kim, Dami; Kim, Hyung-Tae; Ryu, Sung-Soo; Kim, Hyeong-Jun [Korea Institute of Ceramic Engineering and Technology, Bucheon (Korea, Republic of)

2015-02-15

Aluminum titanate (AT) ceramics has high potential as alloy casting refractory materials due to their good thermal shock resistance which results from their low coefficient of thermal expansion. In a previous study, AT doped SiO{sub 2} and ZrO{sub 2} were developed to achieve stability and mechanical strength at high temperature. In this work, the changes of microstructure of AT doped SiO{sub 2} and ZrO{sub 2} were investigated in molten steel. A finger rotating test of sintered AT was carried out at 1300 ℃ for 30 min, 1 h, 2 h, and 3 h. Even if there was no reaction between AT and molten steel, a new surface was formed, followed by the decomposition of AT by the heat from molten steel, which was dominantly constituted of Al and Si due to decomposition of AT and Mullite phases. Some of the new surface layer was found to have been eroded by fluctuations of the molten steel.

Improved dielectric and ferroelectric properties of Mn doped barium zirconium titanate (BZT) ceramics for energy storage applications

Science.gov (United States)

Sangwan, Kanta Maan; Ahlawat, Neetu; Kundu, R. S.; Rani, Suman; Rani, Sunita; Ahlawat, Navneet; Murugavel, Sevi

2018-06-01

Lead free Mn doped barium zirconium titanate ceramic of composition BaZr0.045 (MnxTi1-x)0.955O3 (x = 0.00, 0.01, 0.02) were prepared by solid state reaction method. Tetragonal perovskite structure was confirmed by Rietveld refinement of X-ray diffraction pattern. Analysis of Scanning electron microscope (SEM) micrographs revealed that addition of Mn up to a certain limit accelerates grain growth of BZT ceramic. Static dielectric constant was successfully extended up to high frequencies with an appreciable decrease in dielectric loss about 70% for Mn doped BZT ceramics. The experimental data fitted with Curie Weiss Law and Power Law confirmed first order transition and diffusive behavior of the investigated system. The shifting of Curie temperature (Tc) from 387 K to 402 K indicated tendency for sustained ferroelectricity in doped BZMT ceramics. High value of percentage temperature coefficient of capacitance TCC >10% near Tc was observed for all the compositions and increases with Mn content in pure BZT. At room temperature, BZT modified ceramic corresponding to x = 0.01 composition shows better values of remnant polarization (Pr = 5.718 μC/cm2), saturation polarization (Ps = 14.410 μC/cm2), low coercive field (Ec = 0.612 kV/cm), and highest value of Pr/Ps = 0.396.

Synthesis, processing and characterization of the solid oxide half-cells cathode/electrolyte of strontium-doped lanthanum manganite/Yttria-stabilized zirconia

International Nuclear Information System (INIS)

Chiba, Rubens

2010-01-01

The ceramic films of strontium-doped lanthanum manganite (LSM) and strontium doped lanthanum manganite/Yttria-stabilized zirconia (LSM/YSZ) are used as cathodes of the high temperature solid oxide fuel cells (HTSOFC). These porous ceramic films had been deposited on the YSZ dense ceramic substrate, used as electrolyte, structural component of the module, thus conferring a configuration of half-cell called auto-support. The study of the half-cell it is basic, therefore in the interface cathode/electrolyte occurs the oxygen reduction reaction, consequently influencing in the performance of the HTSOFC. In this direction, the present work contributes for the processing of thin films, using the wet powder spraying technique, adopted for the conformation of the ceramic films for allowing the attainment of porous layers with thicknesses varied in the order of micrometers. The LSM powders were synthesized by the citrate technique and the LSM/YSZ powders synthesized by the solid mixture technique. In the stage of formation were prepared organic suspensions of LSM and LSM/YSZ fed by gravity in a manual aerograph. For the formation of the YSZ substrate was used a hydraulic uniaxial press. The attainment of solid oxide half-cells cathode/electrolyte was possible of crystalline structures hexagonal for phase LSM and cubic for phase YSZ. The half-cells micrographs show that the YSZ substrate is dense, enough to be used as solid electrolyte, and the LSM and LSM/YSZ films are presented porous with approximately 30 μm of thickness and good adherence between the cathodes and the electrolyte. The presence of composite cathode between the LSM cathode and YSZ substrate, presented an increase in the electrochemical performance in the oxygen reduction reaction. (author)

Visible-light induced photocatalysis of AgCl@Ag/titanate nanotubes/nitrogen-doped reduced graphite oxide composites

Science.gov (United States)

Pan, Hongfei; Zhao, Xiaona; Fu, Zhanming; Tu, Wenmao; Fang, Pengfei; Zhang, Haining

2018-06-01

High recombination rate of photogenerated electron-hole pairs and relatively narrow photoresponsive range of TiO2-based photocatalysts are the remaining challenges for their practical applications. To address such challenges, photocatalysts consisting of AgCl covered Ag nanoparticles (AgCl@Ag), titanate nanotubes (TiNT), and nitrogen-doped reduced graphite oxide (rGON) are fabricated through alkaline hydrothermal process, followed by deposition and in situ surface-oxidation of silver nanoparticles. In the synthesized photocatalysts, the titanate nanotubes have average length of about 100 nm with inner diameters of about 5 nm and the size of the formed silver nanoparticles is in the range of 50-100 nm. The synthesized photocatalyst degrades almost all the model organic pollutant Rhodamine B in 35 min and remains 90% of photocatalytic efficiency after 5 degradation cycles under visible light irradiation. Since the oxidant FeCl3 applied for oxidation of surface Ag to AgCl is difficult to be completely removed due to the high adsorption capacity of TiNT and rGON, the effect of reside Fe atoms on photocatalytic activity is evaluated and the results reveal that the residue Fe atom only affect the initial photodegradation performance. Nevertheless, the results demonstrate that the formed composite catalyst is a promising candidate for antibiosis and remediation in aquatic environmental contamination.

Low-temperature sintering and electrical properties of strontium- and magnesium-doped lanthanum gallate with V2O5 additive

Science.gov (United States)

Ha, Sang Bu; Cho, Yoon Ho; Ji, Ho-Il; Lee, Jong-Ho; Kang, Yun Chan; Lee, Jong-Heun

2011-03-01

The effects of a V2O5 additive on the low-temperature sintering and ionic conductivity of strontium- and magnesium-doped lanthanum gallate (LSGM: La0.8Sr0.2Ga0.8Mg0.2O2.8) are studied. The LSGM powders prepared by the glycine nitrate method are mixed with 0.5-2 at.% of VO5/2 and then sintered at 1100-1400 °C in air for 4 h. The apparent density and phase purity of the LSGM specimens are increased with increasing sintering temperature and VO5/2 concentration due to the enhanced sintering and mass transfer via the intergranular liquid phase. The 1 at.% VO5/2-doped LSGM specimen sintered at 1300 °C exhibits a high oxide ion conductivity of ∼0.027 S cm-1 at 700 °C over a wide range of oxygen partial pressure (PO2 =10-27 - 1 atm), thereby demonstrating its potential as a useful electrolyte for anode-supported solid oxide fuel cells (SOFCs) without the requirement for any buffer layer between the electrolyte and anode.

Materials and ceramics on the base of aluminium titanate

International Nuclear Information System (INIS)

Gulamova, D.

1997-01-01

The influence of the doping and technological parameters on the thermodynamical stability of the aluminium titanate is investigated. The condition necessary to make aluminium titanate stable and established. it is shown, how the condition of the synthesis and the content of the admixture phases affect the stability of the solid solutions. The technology of obtaining the ceramics stable with respect to decay (with thermal expansion coefficient CTE = 26x10/sup -6/ grad/sup -1/ and thermoresistancy > 80 heating cycles, sigma curve equal or greater than 80 Mpa) is worked out. (author)

Application of the Rietveld method in powders of strontium-doped lanthanum manganite calcined in different temperatures

International Nuclear Information System (INIS)

Chiba, R.; Vargas, R.A.; Martinez, L.G.; Andreoli, M.; Seo, E.S.M.

2010-01-01

The strontium-doped lanthanum manganite (LSM) is a ceramic material used as cathode in device called High Temperature Solid Oxide Fuel Cell. In this work, the LSM was synthesized by the citrate technique with the objective to get powders without the formation of secondary phases, such as lanthanum oxide and the lanthanum hydroxide, harmful for the functional performance of the device. The definitive calcination temperatures had been 700, 900 and 1100 deg C, due the decomposition of the polymeric precursors to present stabilization from 480 deg C. The analysis by X-ray diffraction of the calcined powders in different temperatures shows the formation only of phase LSM of hexagonal crystalline structure, type pseudo-perovskite. Using the refinement of Rietveld was determined the parameters and volumes of unity cells, atomic positions and occupations. These results confirm that the chemical compositions obtained are similar to the nominal. (author)

Significantly enhanced electrochemical performance of lithium titanate anode for lithium ion battery by the hybrid of nitrogen and sulfur co-doped graphene quantum dots

International Nuclear Information System (INIS)

Ruiyi, Li; Yuanyuan, Jiang; Xiaoyan, Zhou; Zaijun, Li; Zhiguo, Gu; Guangli, Wang; Junkang, Liu

2015-01-01

Graphical abstract: The study reported a facile synthesis of Li4Ti5O12/nitrogen and sulfur co-doped graphene quantum dots (LTO/N,S-GQDs). The unique architecture and the introduction of N,S-GQDs create both ultrafast electron transfer and electrolyte transport. The as-prepared LTO/N,S-GQDs anode provides prominent advantage of specific capacity, high-rate performance and cycle stability. - Highlights: • We reported a new lithium titanate/nitrogen and sulfur co-doped graphene quantum dots hybrid • The synthesis creates a crystalline interconnected porous framework composed of nanoscale LTO • The unique architecture achieves to maximize the rate performance and enhance the power density • Introduction of N,S-GQDs greatly enhances the electron transfer and the storage lithium capacity • The hybrid anode provides an excellent electrochemical performance for lithium-ion batteries - ABSTRACT: The paper reported a facile synthesis of lithium titanate/nitrogen and sulfur co-doped graphene quantum dots(LTO/N,S-GQDs). Tetrabutyl titanate was dissolved in tertbutanol and heated to refluxing state by microwave irradiation. Then, lithium acetate was added into the mixed solution to produce LTO precursor. The precursor was hybridized with N,S-GQDs in ethanol. Followed by drying and thermal annealing at 500 °C in Ar/H_2 to obtain LTO/N,S-GQDs. The synthesis creates fully crystalline interconnected porous framework composed of nanoscale LTO crystals. The unique architecture achieves to maximize the high-rate performance and enhance the power density. More importantly, the introduction of N,S-GQDs don't almost influence on the electrolyte transport, but greatly improve the electron transfer and the storage lithium capacity. The LTO/N,S-GQDs anode exhibits remarkably enhanced electrochemical performance for lithium ion battery. The specific discharge capacity is 254.2 mAh g"−"1 at 0.1C and 126.5 mAh g"−"1 at 10C. The capacity remains 96.9% at least after 2000 cycles

Crystal growth and characterization of europium doped lithium strontium iodide scintillator as an ionizing radiation detector

Science.gov (United States)

Uba, Samuel

High performance detectors used in the detection of ionizing radiation is critical to nuclear nonproliferation applications and other radiation detectors applications. In this research we grew and tested Europium doped Lithium Strontium Iodide compound. A mixture of lithium iodide, strontium iodide and europium iodide was used as the starting materials for this research. Congruent melting and freezing temperature of the synthesized compound was determined by differential scanning calorimetry (DSC) using a Setaram Labsys Evo DSC-DTA instrument. The melting temperatures were recorded at 390.35°C, 407.59°C and freezing temperature was recorded at 322.84°C from a graph of heat flow plotted against temperature. The synthesized material was used as the charge for the vertical Bridgeman growth, and a 6.5 cm and 7.7cm length boule were grown in a multi-zone transparent Mullen furnace. A scintillating detector of thickness 2.53mm was fabricated by mechanical lapping in mineral oil, and scintillating response and timing were obtained to a cesium source using CS-137 isotope. An energy resolution (FWHM over peak position) of 12.1% was observed for the 662keV full absorption peak. Optical absorption in the UV-Vis wavelength range was recorded for the grown crystal using a U-2900 UV/VIS Spectrophotometer. Absorption peaks were recorded at 194nm, 273nm, and 344nm from the absorbance spectrum, various optical parameters such as absorption coefficient, extinction coefficient, refractive index, and optical loss were derived. The optical band gap energy was calculated using Tauc relation expression at 1.79eV.

Doped barium titanate nanoparticles

Indian Academy of Sciences (India)

Wintec

nese doped BaTiO3 ceramics, sintered at 1400°C in air, changes from tetragonal to hexagonal between 0⋅5 and. 1⋅7 mole% of manganese (Langhammer et al 2000). As a driving force of the transformation from the cubic to the hexagonal crystal structure, the influence of the Jahn–. Teller distortion is proposed. The grain ...

Improved ferroelectric and pyroelectric properties of Pb-doped SrBi4Ti4O15 ceramics for high temperature applications

International Nuclear Information System (INIS)

Venkata Ramana, E.; Graça, M.P.F.; Valente, M.A.; Bhima Sankaram, T.

2014-01-01

Highlights: • Sr 1−x Pb x Bi 4 Ti 4 O 15 (SPBT, x = 0 − 0.4) ceramics were synthesized by soft chemical method. • X-ray diffraction analysis confirmed the formation of bismuth layered structure. • SEM images showed plate like grain morphology with random orientation of plate faces. • Pb-doping resulted in improved ferroelectricity of SrBi 4 Ti 4 O 15 ceramics. • Pb-doped SrBi 4 Ti 4 O 15 exhibited improved pyroelectric properties with high T C . -- Abstract: Ferroelectric properties of Pb-modified strontium bismuth titanate ceramics with chemical formula Sr 1−x Pb x Bi 4 Ti 4 O 15 (x = 0–0.4) were investigated. Polycrystalline ceramics were synthesized by soft chemical method to study the effect of Pb-doping on its physical properties. X-ray diffraction analysis revealed a bismuth layered structure for all the compounds. The doping resulted in an increased tetragonal strain and improved ferroelectric properties. Scanning electron microscope images showed plate like grain morphology with random orientation of platelets. The ferroelectric transition temperature of the ceramics increased systematically from 525 °C to 560 °C with the increase of doping concentration. The piezoelectric coefficient (d 33 ) of the ceramics was enhanced significantly with Pb doping, exhibiting a maximum value of 21.8 pC/N for 40 mol.% Pb-doped SBT. Pyroelectric studies carried out using the Byer–Roundy method indicated that the modified SBT ceramics are promising candidates for high temperature pyroelectric applications

Power series fitting of current-voltage characteristics of Al doped ZnO thin film-Sb doped (Ba{sub 0.8}Sr{sub 0.2})TiO{sub 3} heterojunction diode

Energy Technology Data Exchange (ETDEWEB)

Sirikulrat, N., E-mail: scphi003@chiangmai.ac.th

2012-02-29

The current-voltage (I-V) relationship of aluminum doped zinc oxide thin film-antimony doped barium strontium titanate single heterojunction diodes was investigated. The linear I-V characteristics are similar to those of the PN junction diodes. The linear conduction at a low forward bias voltage as predicted by the space charge limited current theory and the trap free square law at a higher forward voltage are observed. The overall current density-voltage (J-V) characteristics of the diodes are found to be well described by the Power Series Equation J= N-Ary-Summation {sub m}C{sub m}V{sup m} where C{sub m} is the leakage constant at particular power m with the best fit for the power m found to be at the fourth and fifth orders for the forward and reverse bias respectively. - Highlights: Black-Right-Pointing-Pointer The n-n isotype heterojunction diodes of ceramic oxide semiconductors were prepared. Black-Right-Pointing-Pointer The current density-voltage (J-V) curves were analyzed using the Power Series (PS). Black-Right-Pointing-Pointer The J-V characteristics were found to be well described with PS at low order. Black-Right-Pointing-Pointer The thermionic emission and diode leakage currents were comparatively discussed.

Ion beam polishing for three-dimensional electron backscattered diffraction

DEFF Research Database (Denmark)

Saowadee, Nath; Agersted, Karsten; Ubhi, H.S.

2013-01-01

averaging and/or poor 3D-EBSD data quality. In this work a low kV focused ion beam was successfully implemented to automatically polish surfaces during 3D-EBSD of La- and Nb-doped strontium titanate of volume 12.6 × 12.6 × 3.0 μm. The key to achieving this technique is the combination of a defocused low k...

Study of irradiation effects in perovskite: use of this matrix for actinides conditioning; Effets de l'irradiation dans une perovskite: utilisation de cette matrice pour un conditionnement des actinides

Energy Technology Data Exchange (ETDEWEB)

Sabathier, C

2003-07-01

The aim of this work is to study a specific conditioning matrix (ceramics) for actinides: the strontium titanate. At first, the choice of strontium titanate is discussed as well as its structure and its ability to incorporate actinides. The different studies carried out on the irradiation effects on the strontium titanate are reviewed. The main ion-matter interactions considered in the energy range used during our experiments are given. The different devices and techniques used with ion beams to carry out our experiments according to the type of sample: monocrystal or polycrystal are described. The experimental results on the behaviour of strontium titanate in terms of irradiation, temperature and ion flux used to damage the matrix are presented. The experimental results on the different steps of strontium titanate annealing are given as well as the identifying of the defects by different analyses techniques (Rutherford backscattering spectroscopy, transmission electron spectroscopy and x-rays spectroscopy). At last, a model of the behaviour of the strontium titanate in the case of an actinide conditioning is proposed and the evolving of the strontium titanate disorder during the storage is discussed. (O.M.)

Electronic and magnetic properties of 3d transition metal-doped strontium clusters: Prospective magnetic superatoms

International Nuclear Information System (INIS)

Chauhan, Vikas; Sen, Prasenjit

2013-01-01

Highlights: • Structural, electronic and magnetic properties of TM-Sr clusters are studied using DFT methods. • CrSr 9 and MnSr 10 have enhanced stability in the CrSr n and MnSrn series. • These two clusters behave as magnetic superatoms. • A qualitative understanding of the magnetic coupling between two superatom units is offered. • Reactivity of these superatoms to molecular oxygen also studied. - Abstract: Structural, electronic and magnetic properties of 3d transition metal doped strontium clusters are studied using first-principles electronic structure methods based on density functional theory. Clusters with enhanced kinetic and thermodynamic stability are identified by studying their hardness, second order energy difference and adiabatic spin excitation energy. CrSr 9 and MnSr 10 are found to have enhanced stability. They retain their structural identities in assemblies, and are classified as magnetic superatoms. A qualitative understanding of the magnetic coupling between two cluster units is arrived at. Reactivity of these superatoms with O 2 molecule is also studied. Prospects for using these magnetic superatoms in applications are discussed

Thermoelectric properties of strontium titanate superlattices incorporating niobium oxide nanolayers

KAUST Repository

Sarath Kumar, S. R.; Hedhili, Mohamed N.; Cha, Dong Kyu; Tritt, Terry M.; Alshareef, Husam N.

2014-01-01

A novel superlattice structure based on epitaxial nanoscale layers of NbOx and Nb-doped SrTiO3 is fabricated using a layer-by-layer approach on lattice matched LAO substrates. The absolute Seebeck coefficient and electrical conductivity of the [(NbOx) a/(Nb-doped SrTiO3)b]20 superlattices (SLs) were found to increase with decreasing layer thickness ratio (a/b ratio), reaching, at high temperatures, a power factor that is comparable to epitaxial Nb-doped SrTiO3 (STNO) films (∼0.7 W m-1 K-1). High temperature studies reveal that the SLs behave as n-type semiconductors and undergo an irreversible change at a varying crossover temperature that depends on the a/b ratio. By use of high resolution X-ray photoelectron spectroscopy and X-ray diffraction, the irreversible changes are identified to be due to a phase transformation from cubic NbO to orthorhombic Nb2O5, which limits the highest temperature of stable operation of the superlattice to 950 K. © 2014 American Chemical Society.

Thermoelectric properties of strontium titanate superlattices incorporating niobium oxide nanolayers

KAUST Repository

Sarath Kumar, S. R.

2014-04-22

A novel superlattice structure based on epitaxial nanoscale layers of NbOx and Nb-doped SrTiO3 is fabricated using a layer-by-layer approach on lattice matched LAO substrates. The absolute Seebeck coefficient and electrical conductivity of the [(NbOx) a/(Nb-doped SrTiO3)b]20 superlattices (SLs) were found to increase with decreasing layer thickness ratio (a/b ratio), reaching, at high temperatures, a power factor that is comparable to epitaxial Nb-doped SrTiO3 (STNO) films (∼0.7 W m-1 K-1). High temperature studies reveal that the SLs behave as n-type semiconductors and undergo an irreversible change at a varying crossover temperature that depends on the a/b ratio. By use of high resolution X-ray photoelectron spectroscopy and X-ray diffraction, the irreversible changes are identified to be due to a phase transformation from cubic NbO to orthorhombic Nb2O5, which limits the highest temperature of stable operation of the superlattice to 950 K. © 2014 American Chemical Society.

Effect of Flowing Water on Sr Sorption Changes of Hydrous Sodium Titanate

OpenAIRE

Youko Takahatake; Atsuhiro Shibata; Kazunori Nomura; Tsutomu Sato

2017-01-01

Radioactive contaminated water has been generated at the Fukushima Daiichi Nuclear Power station (F1NPS). Hydrous sodium titanate (SrTreat®) is able to remove radioactive Strontium (Sr) from this water. Knowing the amount of radioactive nuclides in the used as-received SrTreat® is important for effective disposal and deposition of the F1NPS waste. This study investigated changes in the ability of SrTreat® to sorb Sr, and to understand the causes of changes in the sorbing. An investigation of ...

Synthesis and Characterization of Silicon Titanate as Cation Exchanger and Their Use in the Treatment of Radioactive Liquid Waste

International Nuclear Information System (INIS)

El-Naggar, I.M.; Belacy, N.; Mohamed, D.A.; Abou-Mesalam, M.M.

1999-01-01

Anew class of inorganic ion exchanger called crystalline silicon titanates has excellent chemical and radiation stability. The materials exhibited high selectivity for the ion exchange of cesium, strontium and several other radionuclides from highly acidic solutions. The ion exchange capacity was determined for Na +, Cs +, Co 2+ and Sr 2+ ions and found to be 1.17 , 1.9, 1.38 and 1.52 meq./g, respectively. Besides, the drying temperature of silicon titanates have a profound effect on the ion exchange capacities and distribution coefficient values of the above mentioned cations. Moreover, the studied results of distribution coefficient indicating the ability of separation of these radionuclides from radwaste solutions

Lead removal from aqueous solutions by potassium titanate doped with silica; Remocion de plomo de soluciones acuosas por titanato de potasio dopado con silice

Energy Technology Data Exchange (ETDEWEB)

Aguilar G, M. A.; Aguilar E, A. [Centro de Investigacion en Materiales Avanzados, Miguel de Cervantes No. 120, 31109 Chihuahua (Mexico); Gorokhovsky, A. V.; Escalante G, J. I. [Centro de Investigacion y de Estudios Avanzados, Unidad Saltillo, Carretera Saltillo-Mty Km. 13, Apdo. Postal 663, Saltillo 25000, Coahuila (Mexico)], e-mail: mgzlz@hotmail.com

2009-07-01

This paper is related to elimination of Pb{sup 2+} ions from aqueous solutions by adsorption in potassium tetra titanate doped with silica. The adsorbent was prepared in the form of granules with pastes of potassium poly titanate (45 %), powdered Pyrex glass (5 %) and potato starch (50 %), which were extruded and thermally treated at 1100 C. The structural characteristic of the granulated adsorbent allows reducing the Pb concentration, from the solutions eluted through an adsorption column, to levels below the requirement of national standards. The effects of the time of saturation of the adsorbent and the ph of the solution were also investigated on the effectiveness of the adsorption of Pb. The mechanism of lead adsorption, by the developed adsorbent, is considered as a combination of adsorption, ion-exchange and co-precipitation processes. It is also shown that the lead-saturated adsorbent could be utilized to produce high-strength non-dangerous ceramic materials. (Author)

Mechanoluminescence of Dy doped strontium aluminate nanophosphors

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ravi, E-mail: rvsharma65@gmail.com [Department of Physics, Govt. Arts and Commerce Girls College, Raipur, C.G. 492001 (India); Bisen, D.P. [School of Studies in Physics and Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Chandra, B.P. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (India)

2015-12-15

Nanosized strontium aluminate phosphors activated with Dy{sup 3+} were prepared by a combustion method. Nanophosphor was prepared by this method at reaction temperatures as low as 600 °C. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. The monoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the mechanoluminescence (ML) response curve plotted between time and ML intensity. The H{sub 3}BO{sub 3} added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl{sub 2}O{sub 4}:Dy{sup 3+} without H{sub 3}BO{sub 3.} It was found that the PL and ML intensity increases with increasing concentration of Dy, it becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} in the blue and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} in the yellow-orange wavelength region. - Highlights: • Combustion synthesis route is used to prepare the SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors. • The size of the synthesized sample was found to be in the nano-meter range. • The mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy {sup 3+} nanophosphors is studied. • The photoluminescence of SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors showed blue-shift as compared to bulk. • Effect of H{sub 3}BO{sub 3} on the mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy{sup 3+} was studied.

Optical properties of Er{sup 3+}-doped strontium barium niobate nanocrystals obtained by thermal treatment in glass

Energy Technology Data Exchange (ETDEWEB)

Haro-Gonzalez, P. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain)], E-mail: patharo@ull.es; Lahoz, F. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain); Gonzalez-Platas, J. [Dep. of Fisica Fundamental II, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Caceres, J.M. [Dep. of Edafologia y Geologia, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Gonzalez-Perez, S. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain); Marrero-Lopez, D. [Dep. of Quimica Inorganica, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Capuj, N. [Dep. of Fisica Basica, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Martin, I.R. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain)

2008-05-15

Measurements of the optical properties of Er{sup 3+} ions in strontium barium niobate glass and glass ceramics have been carried out. The glasses have been fabricated using a melt-quenching method, and the glass ceramic samples have been obtained from the glass precursor by a thermal treatment. The ceramic samples formed by a glassy phase, and a crystalline phase contains nanocrystals of Sr{sub 1-x}Ba{sub x}Nb{sub 2}O{sub 6} (SBN) doped with Er{sup 3+} ions with a mean size of {approx}50 nm, as confirmed with XRD. Green up-conversion emission has been obtained under excitation at 800 nm, and the temporal evolution of this emission has been reported with the purpose of determining the involved up-conversion mechanism. These optical measures have confirmed that the Er{sup 3+} ions have been incorporated into the SBN matrix, after a thermal treatment, which produced an increment of the up-conversion efficiency.

Fabrication of Lanthanum Strontium Cobalt Ferrite-Gadolinium-Doped Ceria Composite Cathodes Using a Low-Price Inkjet Printer.

Science.gov (United States)

Han, Gwon Deok; Choi, Hyung Jong; Bae, Kiho; Choi, Hyeon Rak; Jang, Dong Young; Shim, Joon Hyung

2017-11-15

In this work, we have successfully fabricated lanthanum strontium cobalt ferrite (LSCF)-gadolinium-doped ceria (GDC) composite cathodes by inkjet printing and demonstrated their functioning in solid oxide fuel cells (SOFCs). The cathodes are printed using a low-cost HP inkjet printer, and the LSCF and GDC source inks are synthesized with fluidic properties optimum for inkjet printing. The composition and microstructure of the LSCF and GDC layers are successfully controlled by controlling the color level in the printed images and the number of printing cycles, respectively. Anode-support type SOFCs with optimized LSCF-GDC composite cathodes synthesized by our inkjet printing method have achieved a power output of over 570 mW cm -2 at 650 °C, which is comparable to the performance of a commercial SOFC stack. Electrochemical impedance analysis is carried out to establish a relationship between the cell performance and the compositional and structural characteristics of the printed LSCF-GDC composite cathodes.

Hydrogen Solubility in Pr-doped and Un-doped YSZ for One Chamber Fuel Cell

DEFF Research Database (Denmark)

Bay, Lasse; Horita, T.; Sakai, N.

1998-01-01

SIMS analysis. Doping of Pr in the YSZ resulted in a higher intensity of the D ion, which indicated that hydrogen solubility was raised by the doping. The solubility of hydrogen in the electrolyte may affect the performance of one chamber fuel cells. (C) 1998 Elsevier Science B.V. All rights reserved.......Yttria-stabilised zirconia electrolytes (YSZ and Pr-doped YSZ) and yttria-doped strontium cerate (SYC) were tested in a one chamber fuel cell fed with a mixture of methane and air at 1223 K. The obtained performances were 4 mW cm(-2), 3 mW cm(-2), 2.5 mW cm(-2), and 0.15 mW cm(-2) for SYC, 1.8 mol...

Titan

Science.gov (United States)

Müller-Wodarg, Ingo; Griffith, Caitlin A.; Lellouch, Emmanuel; Cravens, Thomas E.

2014-03-01

Introduction I. C. F. Müller-Wodarg, C. A. Griffith, E. Lellouch and T. E. Cravens; Prologue 1: the genesis of Cassini-Huygens W.-H. Ip, T. Owen and D. Gautier; Prologue 2: building a space flight instrument: a P.I.'s perspective M. Tomasko; 1. The origin and evolution of Titan G. Tobie, J. I. Lunine, J. Monteux, O. Mousis and F. Nimmo; 2. Titan's surface geology O. Aharonson, A. G. Hayes, P. O. Hayne, R. M. Lopes, A. Lucas and J. T. Perron; 3. Thermal structure of Titan's troposphere and middle atmosphere F. M. Flasar, R. K. Achterberg and P. J. Schinder; 4. The general circulation of Titan's lower and middle atmosphere S. Lebonnois, F. M. Flasar, T. Tokano and C. E. Newman; 5. The composition of Titan's atmosphere B. Bézard, R. V. Yelle and C. A. Nixon; 6. Storms, clouds, and weather C. A. Griffith, S. Rafkin, P. Rannou and C. P. McKay; 7. Chemistry of Titan's atmosphere V. Vuitton, O. Dutuit, M. A. Smith and N. Balucani; 8. Titan's haze R. West, P. Lavvas, C. Anderson and H. Imanaka; 9. Titan's upper atmosphere: thermal structure, dynamics, and energetics R. V. Yelle and I. C. F. Müller-Wodarg; 10. Titan's upper atmosphere/exosphere, escape processes, and rates D. F. Strobel and J. Cui; 11. Titan's ionosphere M. Galand, A. J. Coates, T. E. Cravens and J.-E. Wahlund; 12. Titan's magnetospheric and plasma environment J.-E. Wahlund, R. Modolo, C. Bertucci and A. J. Coates.

Effective improvement of interface modified strontium titanate based solid oxide fuel cell anodes by infiltration with nano-sized palladium and gadolinium-doped cerium oxide

DEFF Research Database (Denmark)

Abdul Jabbar, Mohammed Hussain; Høgh, Jens Valdemar Thorvald; Zhang, Wei

2013-01-01

The development of low temperature solid oxide fuel cell (SOFC) anodes by infiltration of Pd/Gd-doped cerium oxide (CGO) electrocatalysts in Nb-doped SrTiO3 (STN) backbones has been investigated. Modification of the electrode/electrolyte interface by thin layer of spin-coated CGO (400-500 nm) con...

Nanoscale strontium titanate photocatalysts for overall water splitting.

Science.gov (United States)

Townsend, Troy K; Browning, Nigel D; Osterloh, Frank E

2012-08-28

SrTiO(3) (STO) is a large band gap (3.2 eV) semiconductor that catalyzes the overall water splitting reaction under UV light irradiation in the presence of a NiO cocatalyst. As we show here, the reactivity persists in nanoscale particles of the material, although the process is less effective at the nanoscale. To reach these conclusions, Bulk STO, 30 ± 5 nm STO, and 6.5 ± 1 nm STO were synthesized by three different methods, their crystal structures verified with XRD and their morphology observed with HRTEM before and after NiO deposition. In connection with NiO, all samples split water into stoichiometric mixtures of H(2) and O(2), but the activity is decreasing from 28 μmol H(2) g(-1) h(-1) (bulk STO), to 19.4 μmol H(2) g(-1) h(-1) (30 nm STO), and 3.0 μmol H(2) g(-1) h(-1) (6.5 nm STO). The reasons for this decrease are an increase of the water oxidation overpotential for the smaller particles and reduced light absorption due to a quantum size effect. Overall, these findings establish the first nanoscale titanate photocatalyst for overall water splitting.

Synthesis of Mn-intercalated layered titanate by exfoliation–flocculation approach and its efficient photocatalytic activity under visible–light

International Nuclear Information System (INIS)

Fu, Jie; Tian, Yanlong; Chang, Binbin; Li, Gengnan; Xi, Fengna; Dong, Xiaoping

2012-01-01

A novel Mn-intercalated layered titanate as highly active photocatalyst in visible-light region has been synthesized via a convenient and efficient exfoliation–flocculation approach with divalent Mn ions and monolayer titanate nanosheets. The 0.91 nm interlayer spacing of obtained photocatalyst is in accordance with the sum of the thickness of titanate nanosheet and the diameter of Mn ions. The yellow photocatalyst shows a spectral response in visible-light region and the calculated band gap is 2.59 eV. The photocatalytic performance of this material was evaluated by degradation and mineralization of an aqueous dye methylene blue under visible-light irradiation, and an enhanced photocatalytic activity in comparison with protonated titanate as well as the P25 TiO 2 and N-doped TiO 2 was obtained. Additionally, the layered structure is retained, no dye ions intercalating occurs during the photocatalysis process, and a ∼90% photocatalytic activity can be remained after reusing 3 cycles. - Graphical abstract: Mn-intercalated layered titanate as a novel and efficient visible-light harvesting photocatalyst was synthesized via a convenient and efficient exfoliation–flocculation approach in a mild condition. Highlights: ► Mn-intercalated titanate has been prepared by exfoliation–flocculation approach. ► The as-prepared catalyst shows spectral response in the visible-light region. ► Heat treatment at certain temperature enables formation of Mn-doped TiO 2 . ► Dye can be degradated effectively by the catalyst under visible light irradiation.

Processing and optical characterization of lead calcium titanate borosilicate glass doped with germanium

Science.gov (United States)

Gautam, C. R.; Das, Sangeeta; Gautam, S. S.; Madheshiya, Abhishek; Singh, Anod Kumar

2018-04-01

In this study, various compositions of lead calcium titanate borosilicate glass doped with a fixed amount of germanium were synthesized using the rapid melt quench technique. The amorphous nature of the synthesized glass was confirmed by X-ray diffraction and scanning electron microscopy analyses. The structural and optical properties were deduced using Raman, Fourier transform infrared (FTIR), and ultraviolet-visible (UV-Vis) spectroscopy. FTIR spectroscopy confirmed the presence of borate groups in triangular and tetrahedral coordination. Infrared and Raman analyses detected the vibrational bonds of Gesbnd Osbnd Ge, Bsbnd Osbnd Ge, Sisbnd Osbnd Ge, Sisbnd Osbnd Si, and Pbsbnd Osbnd Ge. The energy band gaps were evaluated for the prepared glass samples based on Tauc plots of the UV-Vis spectra. The calculated values of the optical band gap decreased from 2.91 to 2.85 eV as the PbO content increased from x = 0.0 to x = 0.7. Furthermore, the Urbach energy was studied based on the UV-Vis results to confirm the disordered structure of the glass. The calculated densities of the glass samples (1.5835 g/cm3 to 3.9184 g/cm3) increased as the concentration of PbO increased, whereas they decreased with the molar volume.

Raman analysis of ferroelectric switching in niobium-doped lead zirconate titanate thin films

International Nuclear Information System (INIS)

Ferrari, P.; Ramos-Moore, E.; Guitar, M.A.; Cabrera, A.L.

2014-01-01

Characteristic Raman vibration modes of niobium-doped lead zirconate titanate (PNZT) are studied as a function of ferroelectric domain switching. The microstructure of PNZT is characterized by scanning electron microscopy and X-ray diffraction. Ferroelectric switching is achieved by applying voltages between the top (Au) and bottom (Pt) electrodes, while acquiring the Raman spectra in situ. Vibrational active modes associated with paraelectric and ferroelectric phases are identified after measuring above and below the ferroelectric Curie temperature, respectively. Changes in the relative intensities of the Raman peaks are observed as a function of the switching voltage. The peak area associated with the ferroelectric modes is analyzed as a function of the applied voltage within one ferroelectric polarization loop, showing local maxima around the coercive voltage. This behavior can be understood in terms of the correlation between vibrational and structural properties, since ferroelectric switching modifies the interaction between the body-centered atom (Zr, Ti or Nb) and the Pb–O lattice. - Highlights: • Electric fields induce structural distortions on ferroelectric perovskites. • Ferroelectric capacitor was fabricated to perform hysteresis loops. • Raman analysis was performed in situ during ferroelectric switching. • Raman modes show hysteresis and inflections around the coercive voltages. • Data can be understood in terms of vibrational–structural correlations

Influence of sintering temperature on microstructures and energy-storage properties of barium strontium titanate glass-ceramics prepared by sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Zhu, Jia; Zhang, Yong; Song, Xiaozhen; Zhang, Qian; Yang, Dongliang; Chen, Yongzhou [Beijing Key Laboratory of Fine Ceramics, State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China)

2015-12-15

The sol-gel processing, microstructures, dielectric properties and energy-storage properties of barium strontium titanate glass-ceramics over the sintering temperature range of 1000-1150 C were studied. Through the X-ray diffraction result, it is revealed that the crystallinity increases as the sintering temperature increased from 1000 to 1080 C and has reached a steady-state regime above 1100 C. Scanning electron microscopy images showed that with the increase of sintering temperature, the crystal size increased. Dielectric measurements revealed that the increase in the sintering temperature resulted in a significant increase in the dielectric constant, a strong sharpness of the temperature-dependent dielectric response and a pronounced decrease of the temperature of the dielectric maximum. The correlation between charge spreading behavior and activation energies of crystal and glass was discussed by the employment of the impedance spectroscopy studies. As a result of polarization-electric field hysteresis loops, both the charged and discharged densities increased with increasing sintering temperature. And the maximum value of energy storage efficiency was found to occur at 1130 C. Finally, the dependence of released energy and power densities calculated from the discharged current-time (I-t) curves on the sintering temperature was studied. The relationship between the energy storage properties and microstructure was correlated. Polarization-electric field hysteresis loops for the BST glass-ceramics sintered at different temperatures. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Structural and electrical properties of Nd ion modified lead zirconate titanate nanopowders and ceramics

International Nuclear Information System (INIS)

Da-Wei, Wang; De-Qing, Zhang; Quan-Liang, Zhao; Hong-Mei, Liu; Zhi-Ying, Wang; Mao-Sheng, Cao; Jie, Yuan

2009-01-01

A modified sol-gel method is used for synthesizing Nd ion doped lead zirconate titanate nanopowders Pb 1–3x/2 Nd x Zr 0.52 Ti 0.48 O 3 (PNZT) in an ethylene glycol system with zirconium nitrate as zirconium source. The results show that it is critical to add lead acetate after the reaction of zirconium nitrate with tetrabutyl titanate in the ethylene glycol system for preparing PNZT with an exact fraction of titanium content. It has been observed that the dopant of excess Nd ions can effectively improve the sintered densification and activity of the PNZT ceramics. Piezoelectric, dielectric and ferroelectric properties of the PNZT ceramics are remarkably enhanced as compared with those of monolithic lead zirconate titanate (PZT). Especially, the supreme values of piezoelectric constant (d 33 ) and dielectric constant ( element of ) for the PNZT are both about two times that of the monolithic PZT and moreover, the remnant polarization (P r ) also increases by 30%. According to the analysis of the structures and properties, we attribute the improvement in electrical properties to the lead vacancies caused by the doping of Nd ions

Microstructure and thermal properties of dysprosium and thulium co-doped barium titanate ceramics for high performance multilayer ceramic capacitors

Energy Technology Data Exchange (ETDEWEB)

Kim, Jinseong; Kim, Dowan; Noh, Taimin [School of Materials Science and Engineering, Pusan National University, Busan 609-735 (Korea, Republic of); Ahn, Byungmin [Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-0241 (United States); Lee, Heesoo, E-mail: heesoo@pusan.ac.kr [School of Materials Science and Engineering, Pusan National University, Busan 609-735 (Korea, Republic of)

2011-09-15

Highlights: > Dy/Tm co-doping method in BaTiO{sub 3} was suggested to improve electrical properties and temperature stability simultaneously. > We examined these properties in terms of microstructural analysis and substitution rate. > Increase of Dy{sub 2}O{sub 3} addition enhanced dielectric constant. > Increase of Tm{sub 2}O{sub 3} addition enhanced temperature stability. > Improved electrical properties and temperature stability through Dy/Tm co-doping were deduced from formation of electrons and core-shell structure. - Abstract: The co-doping characteristics on microstructure and thermal properties of barium titanate (BaTiO{sub 3}) were investigated to elucidate formation of core-shell structure by dysprosium (Dy) and thulium (Tm) addition in the BaTiO{sub 3}-Dy{sub 2}O{sub 3}-Tm{sub 2}O{sub 3} system. The dielectrics co-doped with 0.7 mol% Dy{sub 2}O{sub 3} and 0.3 mol% Tm{sub 2}O{sub 3} had the dielectric constant up to 2200 as a function of temperature, which was 30% higher than that of specimen containing only Tm{sub 2}O{sub 3} at the room temperature. It could be explained by the fact that the increase of Dy{sub 2}O{sub 3} addition contributed to the improvement of dielectric constant. On the other hand, the rapid diffusion rate of Dy{sup 3+} ions in BaTiO{sub 3} showed an adverse effect on temperature stability caused by destruction of core-shell. As the compensation for shell expansion in BaTiO{sub 3}, the reinforcement of the core-shell structure through the addition of Tm{sub 2}O{sub 3} was confirmed by TEM-EDS analysis and attributed the temperature coefficient of capacitance (TCC) in a reliability condition (-55 deg. C to 125 deg. C, {Delta}C = {+-}15% or less). The enhanced electrical properties and temperature stability could be deduced from the generation of electrons and the formation core-shell structure in co-doped BaTiO{sub 3} system respectively.

Dielectric behaviour of sodium and potassium doped magnesium

Indian Academy of Sciences (India)

Pure phase of magnesium titanate (MgTiO3) was obtained at 1100°C by both the conventional solid-state method as well as by the flux method starting from hexahydrated magnesium nitrate and titanium dioxide as the reactants. MgTiO3 doped with Na or K was also prepared by the solid-state route. Na and K doped ...

Phase Separation in Doped Mott Insulators

Directory of Open Access Journals (Sweden)

Chuck-Hou Yee

2015-04-01

Full Text Available Motivated by the commonplace observation of Mott insulators away from integer filling, we construct a simple thermodynamic argument for phase separation in first-order doping-driven Mott transitions. We show how to compute the critical dopings required to drive the Mott transition using electronic structure calculations for the titanate family of perovskites, finding good agreement with experiment. The theory predicts that the transition is percolative and should exhibit Coulomb frustration.

Influence of organic solvent treatment on elasticoluminescent property of europium-doped strontium aluminates

International Nuclear Information System (INIS)

Fujio, Yuki; Xu, Chao-Nan; Terasaki, Nao; Ueno, Naohiro

2014-01-01

The influence of an organic solvent treatment on elasticoluminescent (ELS) characteristics of mechanoluminescent (ML) sensor using the composite film consisting of an ELS material and epoxy resin was investigated. We used strontium aluminate doped with a small amount of europium (SrAl 2 O 4 :Eu, SAOE) as an ELS material in this study. After evaluating the ELS characteristics of the fabricated ML sensors using SAOE treated with/without various organic solvents, SAOE treated with methanol and ethanol showed lower ELS intensities than that of untreated SAOE. In contrast, the ELS response curves against strain for the ML sensors using SAOE treated with acetone and toluene, overlapped with that of untreated SAOE. From the characterization of SAOE treated with alcohols, such as methanol and ethanol, we can hypothesize that poor ELS characteristics is due to the degradation of the SAOE grain surfaces by the hydrolyze reaction of SAOE with hydroxyl group of alcohol. Thus, on the basis of the obtained results, we can conclude that the selection of organic solvent used in the preparation of SAOE film is of considerable importance in the development of ML sensor with a highly-reliable ELS characteristic. -- Highlights: • Influence of organic solution treatment on the sensing characteristics of a mechanoluminescent (ML) sensor using SrAl 2 O 4 :Eu has been investigated. • An alcohol treatment of SAOE powder has considerable effect on its ML characteristic. • There is almost no influence of acetone and toluene treatments on ML characteristics

Growth of single crystalline seeds into polycrystalline strontium titanate: Anisotropy of the mobility, intrinsic drag effects and kinetic shape of grain boundaries

International Nuclear Information System (INIS)

Rheinheimer, Wolfgang; Bäurer, Michael; Handwerker, Carol A.; Blendell, John E.; Hoffmann, Michael J.

2015-01-01

We present a suite of measurements and combined analyses of grain growth in SrTiO 3 for oriented single crystals into polycrystals. The growth distance and standard deviation and the microstructure evolution along the single crystal–matrix interface are used to locally characterize the change in migration behavior as a function of temperature, time and interface orientation. The relative grain boundary mobility was determined between 1250 °C and 1600 °C for four crystallographic orientations {1 0 0}, {1 1 0}, {1 1 1} and {3 1 0}. An absolute mobility of these orientations is estimated. Under fast growth conditions the morphology of single crystals shows macroscopic stepping with parts of the interface rotating to low mobility orientations. This effect represents a kinetic influence on the grain boundary morphology. The results also indicate dragging effects on microstructure coarsening, which indicate the existence of a critical driving force for grain growth. This critical driving force seems to be related to an ‘intrinsic’ interface drag similar to the solute drag, but based on intrinsic defects. At 1460 °C the growth of single crystals was significantly faster than expected from the mobility of the polycrystal and was identified as exaggerated grain growth. The findings give new insights into the recently published grain growth anomaly of strontium titanate, leading to a hypothesis based on the temperature dependent relative mobility of {1 0 0} oriented grain boundaries

Effect of elevated concentrations of strontium and iron on the structural and dielectric characteristics of Ba{sub (1-x-y)}Sr{sub (x)}Ti Fe{sub (y)}O{sub 3} prepared through sol-gel technique

Energy Technology Data Exchange (ETDEWEB)

Nur, Omer; Willander, Magnus; Israr, Muhammad Q. [Department of Science and Technology, Campus Norrkoeping, Linkoeping University, SE-60174, Norrkoeping (Sweden); Desouky, Fawzy G. El; Salem, Mohamed A.; Abou Hamad, Ali B. [National Research Center (NRC), Solid State Physics Department, Giza (Egypt); Battisha, Inas K., E-mail: szbasha@yahoo.com [National Research Center (NRC), Solid State Physics Department, Giza (Egypt)

2012-07-15

Nano-composite Ba{sub 1-x}Sr{sub (x)}TiO{sub 3} (BST), where x=0.01-0.50 and doped with different concentrations of iron Ba{sub (1-x-y)}Sr{sub (x)}TiFe {sub (y)}O{sub 3} (BSTF), where x=0.01 and y=0.01-0.05 powders were prepared by sol-gel method. The effect of increasing the iron and strontium concentrations substituted in Barium strontium titanate system will be studied. The prepared samples have a tetragonal crystalline phase after sintering for 1 h at 750 Degree-Sign C in air. The structural and the morphological features of the systems have been studied using X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM). The dielectric properties of the BST and BSTF systems have been investigated as a function of temperature and frequency. The dielectric measurements are carried out in the frequency range 42 Hz-1 MHz, at a temperature ranging between 25 and 250 Degree-Sign C. The results showed a decrease in T{sub c} temperature giving the following values 90 and 85 Degree-Sign C for B{sub 10}ST and B{sub 10}ST{sub 5}F prepared powder samples, respectively, implying tetragonal, feroelectric phase at lower temperature into cubic, para-electric phase at temperature higher than T{sub c}.

Production of Strontium-90 Thermal Power Sources; Fabrication de sources d'energie thermique au strontium-90; Proizvodstvo istochnikov ''teplovoj ehnergii iz Sr''9''0; Preparacion de fuentes de energia termica con estroncio-90

Energy Technology Data Exchange (ETDEWEB)

Cochran, J. S.; Bloom, J. L.; Schneider, A. [Martin Company, Nuclear Division, Baltimore 3, MD (United States)

1963-11-15

One of the most attractive fields for utilization of large quantities of waste fission products is the field of direct-conversion power supplies for remote locations. Strontium-90 is being given the greatest exploitation because of its availability, nuclear properties, and the relative ease with which it can be fabricated into compact heat sources. Strontium-90 fuelled generators are being used to power automatic weather stations and navigational aids, and consideration is being given to the use of strontium-90 as a power source for space vehicles. Evaluation of several potentially useful strontium compounds led to the selection of the titanate as exhibiting overall properties most desirable for this purpose. Strontium-90, separated from crude fission product streams and purified to the requisite degree by the USAEC's Hanford Works, is shipped in the form of the carbonate to a hot cell facility operated by the Martin Company, where it is converted to titanate pellets. This process is an adaption to remote operation of conventional chemical and ceramic techniques. The pellets are encapsulated in Hastelloy C containers for use in thermoelectric power supplies. Unusual operational problems are encountered because the large quantities of strontium-90 handled (potentially millions of curies per year) represent formidable radiation and contamination hazards. Details of the facility, equipment, process, and safety criteria are given. The operational experience gained during the recent processing of the first 250 000 curies of strontium-90 into fuel for a SNAP-7 generator is described. Encapsulation, calorimetry, decontamination, and waste disposal procedures are also outlined. (author) [French] L'une des utilisations les plus interessantes des produits de fission en grande quantite consiste a les employer comme sources d'energie par combustion directe pour des installations geographiquement isolees. C'est le strontium-90 qui est l e plus utilise parce qu'on en dispose en

STRONTIUM PRECIPITATION

Science.gov (United States)

McKenzie, T.R.

1960-09-13

A process is given for improving the precipitation of strontium from an aqueous phosphoric-acid-containing solution with nickel or cobalt ferrocyanide by simultaneously precipitating strontium or calcium phosphate. This is accomplished by adding to the ferrocyanide-containing solution calcium or strontium nitrate in a quantity to yield a concentration of from 0.004 to 0.03 and adjusting the pH of the solution to a value of above 8.

Effect of Nb on barium titanate prepared from citrate solutions

Directory of Open Access Journals (Sweden)

Stojanović Biljana D.

2002-01-01

Full Text Available The influence of the addition of dopants on the microstructure development and electrical properties of BaTiO3 doped with 0.2, 0.4, 0.6, 0.8 mol% of Nb and 0.01 mol% of Mn based compounds was studied. Doped barium titanate was prepared using the polymeric precursor method from citrate solutions. The powders calcined at 700°C for 4 hours were analysed by infrared (IR spectroscopy to verify the presence of carbonates, and by X-ray diffraction (XRD for phase formation. The phase composition, microstructure and dielectric properties show a strong dependence on the amount of added niobium.

Titan!

Science.gov (United States)

Matson, Dennis L.

2010-05-01

Cassini-Huygens achieved Saturnian orbit on July 1, 2004. The first order of business was the safe delivery of the Huygens atmospheric probe to Titan that took place on January 14, 2005. Huygens descended under parachute obtaining observations all the way down to a safe landing. It revealed Titan for the first time. Stunning are the similarities between Titan and the Earth. Viewing the lakes and seas, the fluvial terrain, the sand dunes and other features through the hazy, nitrogen atmosphere, brings to mind the geological processes that created analogous features on the Earth. On Titan frozen water plays the geological role of rock; liquid methane takes the role of terrestrial water. The atmospheres of both Earth and Titan are predominately nitrogen gas. Titan's atmosphere contains 1.5% methane and no oxygen. The surface pressure on Titan is 1.5 times the Earth's. There are aerosol layers and clouds that come and go. Now, as Saturn proceeds along its solar orbit, the seasons are changing. The effects upon the transport of methane are starting to be seen. A large lake in the South Polar Region seems to be filling more as winter onsets. Will the size and number of the lakes in the South grow during winter? Will the northern lakes and seas diminish or dry up as northern summer progresses? How will the atmospheric circulation change? Much work remains not only for Cassini but also for future missions. Titan has many different environments to explore. These require more capable instruments and in situ probes. This work was conducted at the Jet Propulsion Laboratory, California Institute of Technology under contract with the National Aeronautics and Space Administration.

Infiltrated La_0.4Sr_0.4Fe_0.03Ni_0.03Ti_0.94O₃ based anodes for all ceramic and metal supported solid oxide fuel cells

DEFF Research Database (Denmark)

Nielsen, Jimmi; Persson, Åsa Helen; Sudireddy, Bhaskar Reddy

2017-01-01

performing nanostructured Ni:CGO electrocatalyst coated A site deficient Lanthanum doped Strontium Titanate (La0.4Sr0.4Fe0.03Ni0.03Ti0.94O3) based anodes. The anodes were incorporated into the co-sintered DTU metal supported solid oxide fuel cell design and large sized 12 cm × 12 cm cells were fabricated....... The titanate material showed good processing characteristics and surface wetting properties towards the Ni:CGO electrocatalyst coating. The cell performances were evaluated on single cell level (active area 16 cm2) and a power density at 0.7 V and 700 °C of 0.650 Wcm−2 with a fuel utilization of 31...

Platinum-doped titanate nanotubes/reduced graphene oxide: photocatalytic activity and flame retardancy

Science.gov (United States)

Liu, Guangya; Sang, Bin; Zhou, Zhiqi; Li, Zhiwei

2018-01-01

The ‘white pollution’ produced by wasted flexible polyvinyl chloride (PVC) with poor degradation ability and the potential fire hazard of PVC with high flammability not only restrict their application but also cause serious environmental problem. Thus platinum-doped titanate nanotubes/reduced graphene oxide (denoted as Pt-TNTs/rGO) nanocomposites were prepared by a facile method in order to improve the visible photodegradation and get rid of the ‘white pollution’ as well as flame retardancy of PVC. The photodegradation activity and flame retardancy effect of the as-prepared Pt-TNTs/rGO nanocomposites were investigated by ultraviolet and visible light irradiation as well as cone calorimetry. Results show that the Pt-TNTs/rGO-PVC nanocomposites exhibit enhanced visible light photodegradation performance (with mass loss being 6.5%) during 15 day exposure to solar irradiation, and good flame retardancy (providing a 44% reduction of total smoke release as compared with that of PVC matrix). Besides, Pt-TNTs/rGO-PVC nanocomposites show suppressed smoke and reduced CO production as compared with the PVC matrix. These results demonstrate that Pt-TNTs/rGO not only get rid of the ‘white pollution’ as the photocatalyst but also improve the fire safety of PVC as the flame retardant. This could be ascribed to the combination effect between Pt-TNTs and rGO. The present research, hopefully, is to pave a potential pathway to constructing polymer-matrix composites with desired photodegradation activity and flame retardancy, thereby shedding light on simultaneously dealing with the ‘white pollution’ and high flammability of polymer matrix like PVC.

Screening dynamics in doped titanates

Energy Technology Data Exchange (ETDEWEB)

Rubensson, J.E.; Luening, J.; Eisebitt, S. [Forschungszentrum Juelich (Germany)] [and others

1997-04-01

The time scale for carrier relaxation in semiconductors is on the same order of magnitude as the life time of shallow core hole states (a few femtoseconds). Resonant Inelastic soft X-ray scattering (RIXS) which involves (virtual) excitations of core levels consequently contains information about the time development of the electronic structure on this time scale. In many cases one can treat the scattering in an absorption (SXA) followed-by-emission (SXE) picture, where simply the rates for various processes can be compared with the intermediate core hole state decay rate as an internal {open_quotes}clock{close_quotes}. By variation of x (0 < x < 1) in La{sub x}Sr{sub 1{minus}x}TiO{sub 3}, the amount of Ti d electrons in the system can be controlled. SrTiO{sub 3} (x=0) is an insulator with an empty Ti d band. With increasing x, electrons are doped into the Ti d-band, and LaTiO{sub 3} (x=1) is a Mott Hubbard insulator with a Ti 3d{sup 1} configuration. In this work the authors demonstrate that the rate for Ti 2p core hole screening in La{sub x}Sr{sub 1{minus}x}TiO{sub 3} is doping dependent. The screening rate increases with the availability of Ti 3d electrons, and they estimate it to be 3.8 x 10{sup 13}/sec in La{sub 0.05}Sr{sub 0.95}TiO{sub 3}.

Phase transformations in lead zirconate-titanate doped with lanthanum

Energy Technology Data Exchange (ETDEWEB)

Ishchuk, V M; Morozov, E M

1979-07-01

Presented are the results of studies on the character of phase transitions of the lead-lanthanum zirconate-titanate (LLZT) system. The replacement of lead by lanthanum leads to the expansion of the region of antisegnetoelectric (ASE) states of solid solutions of lead zirconate-titanate (LZT) in the direction of PbTiO/sub 3/ concentration growth. An intermediate region is revealed between segnetoelectric (SE) and ASE states, material properties in which depend on their prehistory: annealed samples are in the ASE state, whereas the application of electric field exceeding some critical value induces the SE state. A family of phase diagrams obtained at consequent replacement of lead by lanthanum permits to identify phase states in any series of LLZT with a constant ratio of Zr:Ti, in the x/65/35 series in particular. Thermally depolarized state of materials of this series at x<6.5 is shown to be antisegnetoelectric at all the temperatures below the Curie point Tsub(c), and heating causes phase transition of ASE..-->..PE (paraelectric state) at Tsub(c). Polarized samples being heated, a successiveness of phase transitions of SE..-->..ASE takes place at T/sub 0/, and that of ASE reversible PE at Tsub(C) (Tsub(0)..ASE phase transition in the LZT system.

Resistive switching phenomena of extended defects in Nb-doped SrTiO3 under influence of external gradients

International Nuclear Information System (INIS)

Rodenbuecher, Christian

2014-01-01

Redox-based memristive materials have attracted much attention in the last decade owing to their ability to change the resistance upon application of an electric field making them promising candidates for future non-volatile memories. However, a fundamental understanding of the nature of the resistive switching effect, which is indispensable for designing future technological applications,is still lacking. As a prototype material of a memristive oxide, strontium titanate (SrTiO 3 ) has been investigated intensively and it was revealed that the valence change of a Ti ''d'' electron plays an important role during resistive switching related to insulator-to-metal transition. Such a transition can be induced by electrical gradients, by chemical gradients, by a combination of these gradients or by donor doping. Hence, SrTiO 3 doped with the donor Nb should have metallic properties and is used commonly as a conducting substrate for the growth of functional oxide thin films. Nevertheless,the resistive switching effect has also be observed in Nb-doped SrTiO 3 . This paradoxical situation offers a unique opportunity to gain an insight into the processes during the insulator-to metal transition. In this thesis, a comprehensive study of the influence of external gradients on SrTiO 3 :Nb single crystals is presented. The focus is especially set on the investigation of the crystallographic structure, the chemical composition, the electronic structure, the lattice dynamics and the electronic transport phenomena using surface-sensitive methods on the macro- and nanoscale. On the as-received epi-polished single crystals, the evolution of a surface layer having a slight excess of strontium and - in contrast to the bulk of the material - semiconducting properties are observed. Hence, the key for understanding of the resistive switching effect is the knowledge of the nature of the surface layer. On the basis of systematic studies of the influence of external

Doped Tl-1212 and Tl-1223 superconductors

International Nuclear Information System (INIS)

Eder, M.H.

2001-09-01

This work describes the preparation and characterization of thallium-lead-strontium-barium-calcium-(uranium)-copperoxide (Tl-1212, Tl-1223) high-temperature superconductors. The precursors were prepared via nitrate method. After calcination the oxidic powders were mixed with stoichiometric amounts of an Tl 2 O 3 , PbO, Er 2 O 3 and Gd 2 O 3 by milling and afterwards uniaxial compressed. Sintering was carried out in silver foils. X-ray diffractometry and high-resolution microscopy in combination with scanning electron microscopy (including EDAX) were used to study the influence of varying thallium/lead-, strontium/barium-, calcium/rare earth element ratios and the effect of uranium on the phase composition and microstructure of bulk superconductors. Furthermore the influence of the composition on the electrical and magnetical properties was studied. On phase pure Tl-1212 and Tl-1223 superconductors NMR-measurements were done. Small amounts of gadolinium and erbium instead of calcium and excess-uranium have a positive impact on the electrical and magnetical properties of the Tl-1223 superconductors. Higher amounts of these doping elements favor the Tl-1212 phase. Tl-1212 superconductors with varying thallium/lead- strontium/barium- and calcium/gadolinium ratios were prepared phasepure in wide range of doping. Transition temperatures up to 96 K were achieved. It was shown that lead has an oxidation number of +4 and thallium of +3. (author)

Dielectric behaviour of sodium and potassium doped magnesium ...

Indian Academy of Sciences (India)

Dielectric behaviour of sodium and potassium doped magnesium titanate. VISHNU SHANKER. ∗. , SANTOSH KUMAR and T SURENDAR. Department of Chemistry, National Institute of Technology, Warangal 506 004, India. MS received 10 November 2011; revised 27 February 2012. Abstract. Pure phase of magnesium ...

Studies on sintered titanates and zeolites as hosts for medium-level radioactive waste

International Nuclear Information System (INIS)

Forberg, S.; Westermark, T.; Faelth, L.

1981-01-01

In Sweden, a system for transferring long-lived activities from organic to inorganic ion exchangers such as titanates and zeolites was demonstrated on a bench scale. The stability of this system depends on the conditioning of the inorganic ion exchangers. The purpose of this paper was to study and compare the quality of the products obtained by hot pressing and hot isostatic pressing in order to guide the choice of full scale equipment. Due to the leakage of argon, the hot isostatic pressing did not appear to have an advantage. The extremely large surfaces of authentic titanates must be ascribed to this phenomenon. The merits of the two sintering methods could not be objectively compared from the results obtained. Therefore, more experiments are needed and planned. These are studies on the conditioning of the titanates previous to the sintering, on the welding technique and performance, and at a higher sintering temperature, 1300 0 C, known to yield very good results. Formally, a leach rate of 3 μg d -1 cm -2 for the zeolites corresponds to the leaching out of cesium from a surface layer of 0.15 cm during 300 years. The same leach rate of strontium from titanates corresponds to a depth of 0.08 cm for 300 years. Bearing in mind that the temperature of the deposit will be at least 80 0 C lower, and the water flow much lower, the examples mentioned here might be quite satisfying. After a more successful sintering, the leach rates may be still better and a leaching test at more realistic conditions might be worthwhile

Hydrothermal Synthesis of Nitrogen-Doped Titanium Dioxide and Evaluation of Its Visible Light Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Junjie Qian

2012-01-01

Full Text Available Nitrogen-doped titanium dioxide (N-doped TiO2 photocatalyst was synthesized from nanotube titanic acid (denoted as NTA; molecular formula H2Ti2O5·H2O precursor via a hydrothermal route in ammonia solution. As-synthesized N-doped TiO2 catalysts were characterized by means of X-ray diffraction, transmission electron microscopy, diffuse reflectance spectrometry, X-ray photoelectron spectroscopy, electron spin resonance spectrometry and Fourier transform infrared spectrometry. It was found that nanotube ammonium titanate (NAT was produced as an intermediate during the preparation of N-doped TiO2 from NTA, as evidenced by the N1s X-ray photoelectron spectroscopic peak of NH4 + at 401.7 eV. The catalyst showed much higher activities to the degradation of methylene blue and p-chlorophenol under visible light irradiation than Degussa P25. This could be attributed to the enhanced absorption of N-doped TiO2 in visible light region associated with the formation of single-electron-trapped oxygen vacancies and the inhibition of recombination of photo-generated electron-hole pair by doped nitrogen.

Simulating the Transfer of Strontium-90 from Soil to Leafy Vegetables by Using Strontium-88.

Science.gov (United States)

Kuke, Ding; Shujuan, Liu; Yingxue, He; Dong, Yan; Fengshou, Zhang; Shuifeng, Wang; Jinghua, Guo; Wei, Zhang; Xin, Wang; Xiaoyan, Jiang

The transfer, from soil to Chinese cabbage and spinach, of radioactive strontium-90 released as a result of accidents in nuclear power stations was studied using a stable isotope of strontium, namely nuclide strontium-88 ( 88 Sr). The study led to an experimental model for assessing the hazard of radionuclide strontium-90 ( 90 Sr) entering the food chain and for predicting the risk to food safety. Chinese cabbage and spinach were grown in pots in a greenhouse and irrigated with deionized water containing known quantities of strontium. Based on the strontium content of that water, the plants were divided into five groups (treatments) and strontium content of the soil, and 30-day-old plants were determined by inductively coupled plasma atomic emission spectroscopy instrument (ICP-AES). Data on the strontium content of soil and plants enabled the development of a model using MATLAB, a mathematical software package, which included curve fitting and problem solving using regression equations and differential equations. Although strontium curves for leaves, stems, and roots of Chinese cabbage were not exactly the same, all showed a non-linear increase when compared with the increase in the content of strontium in soil. Strontium curves for leaves, stems, and roots of spinach were very similar and showed an initial increase followed by a decrease. Strontium concentrations in both Chinese cabbage and spinach were initially related to the concentrations of sodium and sulfur, the next two relevant nuclides being calcium and magnesium. The relationship between calcium and strontium in Chinese cabbage was different from that in spinach. By using 88 Sr to simulate the transfer of radionuclide 90 Sr from soil to a crop, the relevant data required to deal with accidental release of strontium can be obtained using a fitting curve and regression equations, thereby providing some experimental basis for evaluating the potential hazards posed by such accidents to the food chain.

Effects of atmosphere in sintering pure or doped PZT with barium and strontium ions; Efeito da atmosfera na sinterizacao do PZT puro ou dopado com ions bario e estroncio

Energy Technology Data Exchange (ETDEWEB)

Simoes, A.Z.; D`Alkimin, R.; Zaghete, M.A.; Perazolli, L.; Varela, J.A.; Gimenes, E.R. [UNESP, Araraquara, SP (Brazil). Inst. de Quimica

1996-05-01

Lead zirconate titanate powder with Zr/Ti ratio of 50/50 was prepared by Pechini method and doped with 1,0; 3,0 and 5,0 mol% of Ba or Sr ions. The powder was calcined at 700 deg C by 3 hours and milled by 6 hours in isopropyl alcohol. Surface area was measured by BET method and the purity of the powder characterized by IV. DRX was used to characterize the crystal structure. The powder was isostatically pressed at 230 MPa and sintered in a dilatometer furnace with constant heating rate of 10 deg C/min up to 1100 deg C. Argon, synthetic air oxygen and oxygen with water vapor were used at atmosphere. The presence of Ba or Sr ions reduce the temperature of maximum sintering rate for all considered atmospheres. The effects of each sintering atmosphere of doped PZT is discussed. (author) 6 refs., 3 figs., 2 tabs.

Computational studies of layered trititanates with magnetic doping

Science.gov (United States)

Heath, Caleb; Barraza-Lopez, Salvador; Tian, Z. Ryan

Layered titanate nanostructures are of great interest due to their ease of synthesis, modifiability, and variety in application. A profusion of experimental literature exists for these compounds but existing computational work has been limited in both quantity and scope. We examine hydrogen trititanate (H2Ti3O7) with and without magnetic substitutional doping. Band structure, elastic properties, material stability, and magnetic properties of these titanates will be discussed. This research is supported by the Arkansas High Performance Computing Center which is funded through multiple National Science Foundation Grants and the Arkansas Economic Development Commission.

Isotope exchange of strontium and molybdate ions in strontium polymolybdates

International Nuclear Information System (INIS)

Atun, G.

2002-01-01

The heterogeneous isotopic exchange reactions in strontium polymolybdates of Sr 2+ and MoO 4 2- ions in the strontium nitrate and sodium molybdate solutions have been studied using 90 Sr and 99 Mo as tracers. Electrometric methods have been used to study the compositions of strontium molybdates obtained by adding strontium chloride to a progressively acidified solution of sodium molybdate. It has been found that the exchange fraction increases with increasing chain length of strontium polymolybdate. The exchange equilibrium constant (K ex ) has been calculated between 298 and 348 K as well as ΔG deg, ΔH deg and ΔS deg. The results indicate that Sr 2+ cations have a much higher affinity for exchangers than MoO 4 2- anions. By fitting the data to the Dubinin-Radushkevich (D-R) isotherm it has been shown that the exchange capacity (X m ) for both ions is affected by the ion adsorption process at low temperatures and by the ion exchange process at high temperatures. At high concentrations, the recrystallization process contributes to on the cation exchange but is ineffective on the anion exchange mechanism. (author)

Thermal stabilities of electromechanical properties in cobalt-modified strontium bismuth titanate (SrBi{sub 4}Ti{sub 4}O{sub 15})

Energy Technology Data Exchange (ETDEWEB)

Wang, Qian; Cao, Zhao-Peng; Wang, Chun-Ming, E-mail: wangcm@sdu.edu.cn; Fu, Qing-Wei; Yin, De-Fu; Tian, Hu-He

2016-07-25

Bismuth layer-structured ferroelectric (BLSF) strontium bismuth titanate (SrBi{sub 4}Ti{sub 4}O{sub 15}, SBT) ceramic oxides with B-site cobalt substitutions have been synthesized using conventional solid–state reaction. The dielectric, piezoelectric, and ferroelectric properties of cobalt-modified SBT are investigated in detail. The results indicate that cobalt is very effective in promoting the piezoelectric performance of SBT. The SBT modified with 3 mol% Co{sup 3+} (SBT-3Co) exhibits the optimized piezoelectric properties, with a piezoelectric constant d{sub 33} of 28 pC/N, which is the highest value among the modified SBT-based piezoelectric ceramics ever reported. The temperature-dependent electrical impedance, resonance frequencies, and electromechanical coupling factors (k{sub p} and k{sub t}) reveal that the cobalt-modified SBT ceramics have good thermal stabilities of electromechanical properties up to 300 °C. These results demonstrate that the cobalt-modified SBT ceramics are promising materials for high temperature piezoelectric sensors applications. - Graphical abstract: The manuscript deals with the thermal stabilities of piezoelectric properties of cobalt-modified SrBi{sub 4}Ti{sub 4}O{sub 15} (SBT) ceramics. The 3 mol% Co{sup 3+} modified SBT (SBT-3Co) ceramics exhibit a piezoelectric constant d{sub 33} of 28 pC/N and a Curie temperature T{sub c} of 528 °C. The SBT-3Co ceramics have good thermal stabilities of electromechanical properties up to 300 °C. - Highlights: • A high level of piezoelectric performance (d{sub 33}∼28 pC/N)is obtained. • High Curie temperature (T{sub c}∼528 °C) is acquired for the optimal composition. • The SBT-3Co exhibits good thermal stabilities of electromechanical properties. • The Co-modified SrBi{sub 4}Ti{sub 4}O{sub 15} is promising as high temperature piezoelectric material.

Integration and High-Temperature Characterization of Ferroelectric Vanadium-Doped Bismuth Titanate Thin Films on Silicon Carbide

Science.gov (United States)

Ekström, Mattias; Khartsev, Sergiy; Östling, Mikael; Zetterling, Carl-Mikael

2017-07-01

4H-SiC electronics can operate at high temperature (HT), e.g., 300°C to 500°C, for extended times. Systems using sensors and amplifiers that operate at HT would benefit from microcontrollers which can also operate at HT. Microcontrollers require nonvolatile memory (NVM) for computer programs. In this work, we demonstrate the possibility of integrating ferroelectric vanadium-doped bismuth titanate (BiTV) thin films on 4H-SiC for HT memory applications, with BiTV ferroelectric capacitors providing memory functionality. Film deposition was achieved by laser ablation on Pt (111)/TiO2/4H-SiC substrates, with magnetron-sputtered Pt used as bottom electrode and thermally evaporated Au as upper contacts. Film characterization by x-ray diffraction analysis revealed predominately (117) orientation. P- E hysteresis loops measured at room temperature showed maximum 2 P r of 48 μC/cm2, large enough for wide read margins. P- E loops were measurable up to 450°C, with losses limiting measurements above 450°C. The phase-transition temperature was determined to be about 660°C from the discontinuity in dielectric permittivity, close to what is achieved for ceramics. These BiTV ferroelectric capacitors demonstrate potential for use in HT NVM applications for SiC digital electronics.

Application of titanates, niobates, and tantalates to neutralized defense waste decontamination: materials properties, physical forms, and regeneration techniques. Final report

International Nuclear Information System (INIS)

Dosch, R.G.

1981-01-01

A study of the application of sodium titanate (ST) to the decontamination of neutralized defense waste has been completed. The work was directed at Sr removal from dissolved salt cake, simulated in this work with a 6.0 N NaNO 3 - 0.6 N NaOH solution. Three physical forms of the titanates were developed including powder, pellets, and titanate-loaded resin beads and all were found to be superior to conventional organic ion exchange in this application. When spent, the titanate materials can be calcined to an oxide from which is a stable waste form in itself or can be added directly to a glass melter to become part of a vitrified waste form. Radiation stability of titanate powder and resin forms was assessed in tests in which these materials were exposed to 60 Co radiation. The strontium exchange capacity of the powder remained constant through a dose of 3 x 10 7 rads and retained 50% capacity after a dose of 2 x 10 9 rads. The primary mechanism involved in loss of capacity was believed to be heating associated with the irradiation. The resin forms were unchanged through a dose of 5 x 10 8 rads and retained 30% capacity after a dose of 2 x 10 9 rads. The latter dose resulted in visible degradation of the resin matrix. Anion exchange resins loaded with sodium niobate and sodium tantalate were also prepared by similar methods and evaluated for this application. These materials had Sr sorption properties comparable to the titanate material; however, they would have to provide a significant improvement to justify their higher cost

Formation of aluminum titanate with small additions of MgO and SiO2

International Nuclear Information System (INIS)

Guedes-Silva, Cecilia Chaves; Ferreira, Thiago dos Santos; Genova, Luis Antonio; Carvalho, Flavio Machado de Souza

2016-01-01

The formation of aluminum titanate was investigated by isothermal treatments of samples obtained from equimolar mixtures of alumina and titania, containing small amounts of silica and magnesia. Results of differential thermal analysis and Rietveld refinements of data collected by X-ray powder diffraction (XRPD) showed that additions of silica in amounts used in this work did not influence the formation of aluminum titanate. However, the presence of magnesia favored the formation of aluminum titanate in two steps, first one by incorporating Mg 2+ into Al 2 TiO 5 lattice during its initial formation, and the second one by accelerating the Al 2 TiO 5 formation, contributing to large quantities of this phase. MgO doped samples have also developed a more suitable microstructure for stabilizing of Al 2 TiO 5 , what make them promising for applications such as thermal barriers, internal combustion engines and support material for catalyst. (author)

Influence of dehydrated nanotubed titanic acid on charge transport and luminescent properties of polymer light-emitting diodes with fluorescent dye

Science.gov (United States)

Qian, Lei; Bera, Debasis; Jin, Zhen-Sheng; Du, Zu-Liang; Xu, Zheng; Teng, Feng; Liu, Wei

2007-09-01

In this paper, we discuss the influence of dehydrated nanotubed titanic acid (DNTA) on charge transport and luminescent properties of polymer light-emitting diodes (PLEDs) doped with fluorescent dye. Photoluminescence results confirm the efficient energy transfer from PVK to 4-(dicyanom-ethylene)-2- t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) and tris-(8-hydroxtquinoline) aluminum (Alq 3) in a DNTA-doped device. The device showed lower turn-on voltages and higher charge current by doping with DNTA, which also caused a shift in the exciton's recombination region.

Rheology Of MonoSodium Titanate (MST) And Modified Mst (mMST) Mixtures Relevant To The Salt Waste Processing Facility

Energy Technology Data Exchange (ETDEWEB)

Koopman, D. C.; Martino, C. J.; Shehee, T. C.; Poirier, M. R.

2013-07-31

The Savannah River National Laboratory performed measurements of the rheology of suspensions and settled layers of treated material applicable to the Savannah River Site Salt Waste Processing Facility. Suspended solids mixtures included monosodium titanate (MST) or modified MST (mMST) at various solid concentrations and soluble ion concentrations with and without the inclusion of kaolin clay or simulated sludge. Layers of settled solids were MST/sludge or mMST/sludge mixtures, either with or without sorbed strontium, over a range of initial solids concentrations, soluble ion concentrations, and settling times.

Rheology Of MonoSodium Titanate (MST) And Modified Mst (mMST) Mixtures Relevant To The Salt Waste Processing Facility

International Nuclear Information System (INIS)

Koopman, D. C.; Martino, C. J.; Shehee, T. C.; Poirier, M. R.

2013-01-01

The Savannah River National Laboratory performed measurements of the rheology of suspensions and settled layers of treated material applicable to the Savannah River Site Salt Waste Processing Facility. Suspended solids mixtures included monosodium titanate (MST) or modified MST (mMST) at various solid concentrations and soluble ion concentrations with and without the inclusion of kaolin clay or simulated sludge. Layers of settled solids were MST/sludge or mMST/sludge mixtures, either with or without sorbed strontium, over a range of initial solids concentrations, soluble ion concentrations, and settling times

High-resolution stratigraphy with strontium isotopes.

Science.gov (United States)

Depaolo, D J; Ingram, B L

1985-02-22

The isotopic ratio of strontium-87 to strontium-86 shows no detectable variation in present-day ocean water but changes slowly over millions of years. The strontium contained in carbonate shells of marine organisms records the ratio of strontium-87 to strontium-86 of the oceans at the time that the shells form. Sedimentary rocks composed of accumulated fossil carbonate shells can be dated and correlated with the use of high precision measurements of the ratio of strontium-87 to strontium-86 with a resolution that is similar to that of other techniques used in age correlation. This method may prove valuable for many geological, paleontological, paleooceanographic, and geochemical problems.

Efficient degradation of Methylene Blue dye over highly reactive Cu doped strontium titanate (SrTiO3) nanoparticles photocatalyst under visible light.

Science.gov (United States)

Rahman, Qazi Inamur; Ahmad, Musheer; Misra, Sunil Kumar; Lohani, Minaxi

2012-09-01

Visible light induced photocatalysts of Cu doped SrTiO3 (Cu/SrTiO3) nanoparticles with the size -60-75 nm were prepared via facile sol-gel method. The morphological, optical, crystalline properties and compositions of synthesized Cu/SrTiO3 nanoparticles were thoroughly characterized by field emission scanning electron microscopy (FE-SEM), powder X-ray diffraction (XRD), ultra violet-visible spectroscopy (UV-Vis) and energy dispersive X-ray (EDX). A significant red shift in the UV-diffused reflectance spectrum was observed and the absorption edge shifted to visible region by the Cu doping. Surprisingly, the band gap of SrTiO3 was changed from 3.2 eV drop to 2.96 eV. The photocatalytic activity of the synthesized Cu/SrTiO3 nanoparticles was demonstrated for the degradation of Methylene Blue dye under visible light irradiation. The formation of new acceptor region in Cu/SrTiO3 was responsible for high photocatalytic activity of Cu/SrTiO3 nanoparticles. The results showed that the Methylene Blue dye was degraded by -66% within time span of 2 h over the Cu/SrTiO3 nanoparticles. This dye degradation reaction followed the Langmuir-Hinshelwood kinetics and also exhibited first order reaction rate. The calculated rate constant for the degradation reaction following first order kinetics was k = 0.0016 min(-1).

Effect of working pressure and annealing temperature on ...

Indian Academy of Sciences (India)

roughness was found at higher temperatures as a result of a more heterogeneous growth and less tensions. Keywords. Barium strontium titanate; thin film; pulsed laser deposition; ferroelectric. 1. Introduction. Perovskite barium strontium titanate (BST) thin films are promising candidates for dynamic random access memory.

Rubidium-strontium method

International Nuclear Information System (INIS)

Dubansky, A.

1980-01-01

The rubidium-strontium geological dating method is based on the determination of the Rb and Sr isotope ratio in rocks, mainly using mass spectrometry. The method is only practical for silicate minerals and rocks, potassium feldspars and slates. Also described is the rubidium-strontium isochrone method. This, however, requires a significant amount of experimental data and an analysis of large quantities of samples, often of the order of tons. The results are tabulated of rubidium-strontium dating of geological formations in the Czech Socialist Republic. (M.S.)

Incipient ferroelectric to a possible ferroelectric transition in Te4+ doped calcium copper titanate (CaCu3Ti4O12 ceramics at low temperature as evidenced by Raman and dielectric spectroscopy

Directory of Open Access Journals (Sweden)

Nabadyuti Barman

2017-03-01

Full Text Available Partial replacement of Ti4+ by Te4+ ions in calcium copper titanate lattice improved its dielectric behaviour mostly due to cubic-to-tetragonal structural transformation and associated distortion in TiO6 octahedra. The relative permittivity values (23–30 x 103 of Te4+ doped ceramics is more than thrice that of un-doped ceramics (8 x 103 at 1 kHz. A decreasing trend in relative permittivity with increasing temperature (50–300 K is observed for all the samples. Barrett’s formula, as a signature of incipient ferroelectricity, is invoked to rationalize the relative permittivity variation as a function of temperature. A systematic investigation supported by temperature dependent Raman studies reveal a possible ferroelectric transition in Te4+ doped ceramic samples below 120 K. The possible ferroelectric transition is attributed to the interactions between quasi-local vibrations associated with the micro-clusters comprising TiO6 and TeO6 structural units and indirect dipole-dipole interactions of off-center B–cations (Ti4+ and Te4+ in double perovskite lattice.

Kinetics of isotopic exchange between strontium polymolybdate and strontium ions in aqueous solution

International Nuclear Information System (INIS)

Atun, Gulten; Bilgin, Binay; Kilislioglu, Ayben

2002-01-01

A heterogeneous isotopic exchange reaction of strontium polymolybdate in strontium chloride solution was studied using 90 Sr as a tracer. The effects of low and high strontium chloride concentration on the rate and mechanism of the isotopic exchange reaction were investigated. It was found that, at high concentrations, the rate is independent of strontium concentration, but, at low concentrations, the rate is proportional to the strontium concentration. These results support a hypothesis that, at low concentrations, the rate is controlled by film diffusion, whereas at high concentrations it is controlled by particle diffusion. Experiments were performed at 293, 303 and 313 K. Activation energy of isotopic exchange reaction and thermodynamic parameters ΔH*, ΔS*, and ΔG* were calculated using the Arrhenius and Eyring equations. The results also indicated that recrystallization is a predominant factor in the present exchange reaction

Kinetics of isotopic exchange between strontium polymolybdate and strontium ions in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Atun, Gulten E-mail: gultena@istanbul.edu.tr; Bilgin, Binay; Kilislioglu, Ayben

2002-06-01

A heterogeneous isotopic exchange reaction of strontium polymolybdate in strontium chloride solution was studied using {sup 90}Sr as a tracer. The effects of low and high strontium chloride concentration on the rate and mechanism of the isotopic exchange reaction were investigated. It was found that, at high concentrations, the rate is independent of strontium concentration, but, at low concentrations, the rate is proportional to the strontium concentration. These results support a hypothesis that, at low concentrations, the rate is controlled by film diffusion, whereas at high concentrations it is controlled by particle diffusion. Experiments were performed at 293, 303 and 313 K. Activation energy of isotopic exchange reaction and thermodynamic parameters {delta}H*, {delta}S*, and {delta}G* were calculated using the Arrhenius and Eyring equations. The results also indicated that recrystallization is a predominant factor in the present exchange reaction.

Measurement of strontium-89 and strontium-90 in environmental waters. A tentative reference method

International Nuclear Information System (INIS)

1976-03-01

A tentative reference method for the measurement of 89 Sr and 90 Sr in environmental waters is described. Samples of environmental water sources are collected, preserved with acid-strontium carrier, and analyzed for 89 Sr and/or 90 Sr. The isotopes are separated from the sample water by precipitating with stable strontium carrier as carbonate. The strontium carbonate is dissolved, 90 Sr separated, the strontium reprecipitated as carbonate, filtered, and counted for the combined 89 Sr and 90 Sr activity. The 90 y is allowed to grow in from the 90 y activity; the strontium carbonate is redissolved; the 90 y is separated, precipitated, and counted for the 90 Sr determination. The 89 Sr activity is then determined by difference of the total 89 Sr and 90 y and the separate 90 Sr activities. Recoveries are determined from the added and found (recovered) strontium carrier. Counting efficiencies are determined with prepared standard reference samples. Results are reported in pCi/liter

Formation of aluminum titanate with small additions of MgO and SiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Guedes-Silva, Cecilia Chaves; Ferreira, Thiago dos Santos; Genova, Luis Antonio [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Carvalho, Flavio Machado de Souza, E-mail: cecilia.guedes@ipen.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Geociencias

2016-03-15

The formation of aluminum titanate was investigated by isothermal treatments of samples obtained from equimolar mixtures of alumina and titania, containing small amounts of silica and magnesia. Results of differential thermal analysis and Rietveld refinements of data collected by X-ray powder diffraction (XRPD) showed that additions of silica in amounts used in this work did not influence the formation of aluminum titanate. However, the presence of magnesia favored the formation of aluminum titanate in two steps, first one by incorporating Mg{sup 2+} into Al{sub 2}TiO{sub 5} lattice during its initial formation, and the second one by accelerating the Al{sub 2}TiO{sub 5} formation, contributing to large quantities of this phase. MgO doped samples have also developed a more suitable microstructure for stabilizing of Al{sub 2}TiO{sub 5}, what make them promising for applications such as thermal barriers, internal combustion engines and support material for catalyst. (author)

A study of strontium doped calcium phosphate coatings on AZ31

International Nuclear Information System (INIS)

Singh, Satish S.; Roy, Abhijit; Lee, Boeun E.; Ohodnicki, John; Loghmanian, Autrine; Banerjee, Ipsita; Kumta, Prashant N.

2014-01-01

Calcium phosphate (CaP) coatings have been studied to tailor the uncontrolled non-uniform corrosion of Mg based alloys while simultaneously enhancing bioactivity. The use of immersion techniques to deposit CaP coatings is attractive due to the ability of the approach to coat complex structures. In the current study, AZ31 substrates were subjected to various pretreatment conditions prior to depositing Sr 2+ doped and undoped CaP coatings. It was hypothesized that the bioactivity and corrosion protection of CaP coatings could be improved by doping with Sr 2+ . Heat treatment to elevated temperatures resulted in the diffusion of alloying elements, Mg and Zn, into the pretreated layer. Sr 2+ doped and undoped CaP coatings formed on the pretreated substrates consisted of biphasic mixtures of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA). Electrochemical corrosion experiments indicated that the extent of Sr 2+ doping and pretreatment both influenced the corrosion protection. Cytotoxicity was evaluated with MC3T3-E1 mouse preosteoblasts and human mesenchymal stem cells (hMSCs). For both cell types, proliferation decreased upon increasing the Sr 2+ concentration. However, both osteogenic gene and protein expression significantly increased upon increasing Sr 2+ concentration. These results suggest that Sr 2+ doped coatings are capable of promoting osteogenic differentiation on degradable Mg alloys, while also enhancing corrosion protection, in comparison to undoped CaP coatings

Barium titanate coated with magnesium titanate via fused salt method and its dielectric property

International Nuclear Information System (INIS)

Chen Renzheng; Cui Aili; Wang Xiaohui; Li Longtu

2003-01-01

Barium titanate fine particles were coated homogeneously with magnesium titanate via the fused salt method. The thickness of the magnesium titanate film is 20 nm, as verified by TEM and XRD. The mechanism of the coating is that: when magnesium chloride is liquated in 800 deg. C, magnesium will replace barium in barium titanate, and form magnesium titanate film on the surface of barium titanate particles. Ceramics sintered from the coated particles show improved high frequency ability. The dielectric constant is about 130 at the frequency from 1 to 800 MHz

Structural Contribution to the Ferroelectric Fatigue in Lead Zirconate Titanate (PZT) Ceramics

OpenAIRE

Hinterstein , Manuel; Rouquette , Jerome; Haines , J; Papet , Ph; Glaum , Julia; Knapp , Michael; Eckert , J; Hoffman , M

2014-01-01

International audience; Many ferroelectric devices are based on doped lead zirconate titanate (PZT) ceramics with compositions near the morphotropic phase boundary (MPB), at which the relevant material's properties approach their maximum. Based on a synchrotron x-ray diffraction study of MPB PZT, bulk fatigue is unambiguously found to arise from a less effective field induced tetragonal-to-monoclinic transformation, at which the degradation of the polarization flipping is detected by a less i...

Calcium and Strontium in Swedish Waters and Fish, and Accumulation of Strontium-90

Energy Technology Data Exchange (ETDEWEB)

Agnedal, P O

1966-04-15

The purpose of this study has been to investigate the correlation between calcium and strontium in fish in relation to the concentration of these elements in the water. An investigation of the uptake of strontium-90 has also been made and permissible levels of strontium-90 in the water is calculated based upon the uptake in fish muscle tissues. Lakes with calcium concentrations between 2 - 63 mg/l have been studied and samples from the Baltic coastal water are also included. Three fish species are studied, viz. pike (Esox lucius (L.)), perch (Perca fluviatilis (L.)) and roach (Leuciscus rutilus (L.)). Bones, muscle tissues and skin + scales have been analysed. Strontium-90 measurements have been made showing an increase in both water and fish. Calculations show that in water with about 2 mg Ca/l a 10-fold increase of the existing strontium-90 level might give strontium-90 concentrations in fish muscle tissues close to what is permissible. In lakes with calcium concentrations 20 - 40 mg/l the permissible levels for drinking water will be exceeded before the fish consumption would have to be restricted.

Calcium and Strontium in Swedish Waters and Fish, and Accumulation of Strontium-90

International Nuclear Information System (INIS)

Agnedal, P.O.

1966-04-01

The purpose of this study has been to investigate the correlation between calcium and strontium in fish in relation to the concentration of these elements in the water. An investigation of the uptake of strontium-90 has also been made and permissible levels of strontium-90 in the water is calculated based upon the uptake in fish muscle tissues. Lakes with calcium concentrations between 2 - 63 mg/l have been studied and samples from the Baltic coastal water are also included. Three fish species are studied, viz. pike (Esox lucius (L.)), perch (Perca fluviatilis (L.)) and roach (Leuciscus rutilus (L.)). Bones, muscle tissues and skin + scales have been analysed. Strontium-90 measurements have been made showing an increase in both water and fish. Calculations show that in water with about 2 mg Ca/l a 10-fold increase of the existing strontium-90 level might give strontium-90 concentrations in fish muscle tissues close to what is permissible. In lakes with calcium concentrations 20 - 40 mg/l the permissible levels for drinking water will be exceeded before the fish consumption would have to be restricted

Titan's Radioactive Haze : Production and Fate of Radiocarbon On Titan

Science.gov (United States)

Lorenz, R. D.; Jull, A. J. T.; Swindle, T. D.; Lunine, J. I.

Just as cosmic rays interact with nitrogen atoms in the atmosphere of Earth to gener- ate radiocarbon (14C), the same process should occur in Titan`s nitrogen-rich atmo- sphere. Titan`s atmosphere is thick enough that cosmic ray flux, rather than nitrogen column depth, limits the production of 14 C. Absence of a strong magnetic field and the increased distance from the sun suggest production rates of 9 atom/cm2/s, approx- imately 4 times higher than Earth. On Earth the carbon is rapidly oxidised into CO2. The fate and detectability of 14C on Titan depends on the chemical species into which it is incorporated in Titan's reducing atmosphere : as methane it would be hopelessly diluted even in only the atmosphere (ignoring the other, much more massive carbon reservoirs likely to be present on Titan, like hydrocarbon lakes.) However, in the more likely case that the 14C attaches to the haze that rains out onto the surface (as tholin, HCN or acetylene and their polymers - a much smaller carbon reservoir) , haze in the atmosphere or recently deposited on the surface would therefore be quite intrinsically radioactive. Such activity may modify the haze electrical charging and hence its coag- ulation. Measurements with compact instrumentation on future in-situ missions could place useful constraints on the mass deposition rates of photochemical material on the surface and identify locations where surface deposits of such material are `freshest`.

Effect of sludge solids to mono-sodium titanate (MST) ratio on MST-treated sludge

International Nuclear Information System (INIS)

Saito, H.H.

1999-01-01

The Salt Disposition Systems Engineering Team has selected two cesium removal technologies for further development to replace the In-Tank Precipitation process: small tank tetraphenylborate (TPB) precipitation and crystalline silicotitanate (CST) ion exchange. In the CST ion exchange process, incoming salt solution from storage tanks containing entrained sludge solids is pretreated with monosodium titanate (MST) to adsorb strontium and plutonium. The resulting slurry is filtered using a cross-flow filter, with the permeate sent forward to CST ion exchange columns for cesium removal prior to conversion into Class A grout at the Saltstone Facility. The MST and sludge solids are to be sent for vitrification at the Defense Waste Processing Facility (DWPF). The High Level Waste Division (HLWD) requested that the Waste Processing Technology Section (WPTS) study varying the insoluble sludge solids to MST ratio to determine the relative impact of sludge and MST on filter performance. The purpose of this study was not for an exhaustive comprehensive search for an optimized insoluble sludge solids to monosodium titanate (MST) ratio, but as a scoping study to identify any effects of having an excess of either material. This document reports the results obtained

Rapid determination of strontium-89 and strontium-90 in food and environmental samples by Cerenkov counting

International Nuclear Information System (INIS)

Melin, Judith; Suomela, Jorma

1995-01-01

The method has been developed for emergency situations. Minimum detectable concentrations of 5 Bq/liter, kilogram of strontium-89 and strontium-90 respectively is achievable in the presence of nuclides considered to be released under accidental conditions. Result on the strontium-89 and strontium-90 content in a sample can be obtained within 12 hours. One technician can easily handle 8-10 samples during a working day of eight hours. The determination of the strontium isotopes is accomplished by monitoring the Cerenkov radiation from strontium-89 and yttrium-90 in a liquid scintillation counter. The latter is the daughter product of strontium-90. Prior to the Cerenkov counting the sample is separated from interfering nuclides by oxalate precipitation, chromate precipitation and HDEHP-extraction. The method has to be further improved and evaluated with respect to different soil types such as forest mineral soil layers, agricultural soils and pastures. Furthermore, the decontamination procedure should be evaluated for a sample containing freshly irradiated uranium. (author)

Ferroelectric relaxor behaviour and impedance spectroscopy of Bi2O3-doped barium zirconium titanate ceramics

Science.gov (United States)

Mahajan, Sandeep; Thakur, O P; Bhattacharya, D K; Sreenivas, K

2009-03-01

Bi2O3-doped barium zirconate titanate ceramics, Ba1-xBix(Zr0.05Ti0.95)O3, have been prepared by the conventional solid-state reaction method. The ferroelectric relaxor behaviour and dielectric properties have been investigated in detail. By XRD analysis, it is suggested that up to x = 0.04, Bi3+ substitutes A-site ion, and thereafter with higher Bi3+ content, it enters the B-site sub lattice. Substitution of Bi3+ ions induces ferroelectric relaxor behaviour and the degree of relaxation behaviour increases with bismuth concentration. The remanent polarization and strain behaviour show a slight increase with the substitution level. The degree of hysteresis (strain versus electric field) also reduces from 21.4% to 4.6% with bismuth substitution. Impedance measurements were made on the prepared sample over a wide range of temperatures (300-723 K) and frequencies (40 Hz-1 MHz), which show the presence of both bulk and grain boundary effects in the material. The bulk and grain boundary conductivities determined from impedance study indicate the Arrhenius-type thermally activated process. Impedance spectroscopy is shown to be an efficient method capable of detecting the contributions of the resistances of grains and grain boundaries to the complex impedance of a ceramic system, accurately estimating its electrical conductivity as well as its corresponding activation energies and drawing conclusions on its structural properties.

Ferroelectric relaxor behaviour and impedance spectroscopy of Bi2O3-doped barium zirconium titanate ceramics

International Nuclear Information System (INIS)

Mahajan, Sandeep; Thakur, O P; Bhattacharya, D K; Sreenivas, K

2009-01-01

Bi 2 O 3 -doped barium zirconate titanate ceramics, Ba 1-x Bi x (Zr 0.05 Ti 0.95 )O 3 , have been prepared by the conventional solid-state reaction method. The ferroelectric relaxor behaviour and dielectric properties have been investigated in detail. By XRD analysis, it is suggested that up to x = 0.04, Bi 3+ substitutes A-site ion, and thereafter with higher Bi 3+ content, it enters the B-site sub lattice. Substitution of Bi 3+ ions induces ferroelectric relaxor behaviour and the degree of relaxation behaviour increases with bismuth concentration. The remanent polarization and strain behaviour show a slight increase with the substitution level. The degree of hysteresis (strain versus electric field) also reduces from 21.4% to 4.6% with bismuth substitution. Impedance measurements were made on the prepared sample over a wide range of temperatures (300-723 K) and frequencies (40 Hz-1 MHz), which show the presence of both bulk and grain boundary effects in the material. The bulk and grain boundary conductivities determined from impedance study indicate the Arrhenius-type thermally activated process. Impedance spectroscopy is shown to be an efficient method capable of detecting the contributions of the resistances of grains and grain boundaries to the complex impedance of a ceramic system, accurately estimating its electrical conductivity as well as its corresponding activation energies and drawing conclusions on its structural properties.

A promising lightweight multicomponent microwave absorber based on doped barium hexaferrite/calcium titanate/multiwalled carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Afghahi, Seyyed Salman Seyyed [Imam Hossein University, Department of Materials Science and Engineering (Iran, Islamic Republic of); Jafarian, Mojtaba, E-mail: m.jafarian@srbiau.ac.ir [Islamic Azad University, Young Researchers and Elite Club, Science and Research Branch (Iran, Islamic Republic of); Atassi, Yomen [Higher Institute for Applied Sciences and Technology, Department of Applied Physics (Syrian Arab Republic)

2016-07-15

We present the design of a microwave absorber in the X band based on ternary nanocomposite of doped barium hexaferrite (Ba-M)/calcium titanate (CTO)/multiwall carbon nanotubes (MWCNTs) in epoxy matrix. The hydrothermal method has been used to synthesize Ba-M and CTO nanopowder. The phase identification has been investigated using XRD patterns. Scanning electron microscope, transmission electron microscope, vibrating sample magnetometer, and vector network analyzer are used to analyze the morphology of the different components and the magnetic, electromagnetic, and microwave absorption properties of the final composite absorbers, respectively. As far as we know, the design of this type of multicomponent microwave absorber has not been investigated before. The results reveal that the combination of these three components with their different loss mechanisms has a synergistic effect that enhances the attenuation properties of the final composite. The absorber of only 2.5-mm thickness and 35 wt% of loading ratio exhibits a minimum reflection loss of −43 dB at 10.2 GHz with a bandwidth of 3.6 GHz, while the corresponding absorber based on pure (Ba-M) shows a minimum reflection loss of −34 dB at 9.8 GHz with a bandwidth of 0.256 GHz and a thickness of 4 mm.Graphical Abstract.

Titan Casts Revealing Shadow

Science.gov (United States)

2004-05-01

A rare celestial event was captured by NASA's Chandra X-ray Observatory as Titan -- Saturn's largest moon and the only moon in the Solar System with a thick atmosphere -- crossed in front of the X-ray bright Crab Nebula. The X-ray shadow cast by Titan allowed astronomers to make the first X-ray measurement of the extent of its atmosphere. On January 5, 2003, Titan transited the Crab Nebula, the remnant of a supernova explosion that was observed to occur in the year 1054. Although Saturn and Titan pass within a few degrees of the Crab Nebula every 30 years, they rarely pass directly in front of it. "This may have been the first transit of the Crab Nebula by Titan since the birth of the Crab Nebula," said Koji Mori of Pennsylvania State University in University Park, and lead author on an Astrophysical Journal paper describing these results. "The next similar conjunction will take place in the year 2267, so this was truly a once in a lifetime event." Animation of Titan's Shadow on Crab Nebula Animation of Titan's Shadow on Crab Nebula Chandra's observation revealed that the diameter of the X-ray shadow cast by Titan was larger than the diameter of its solid surface. The difference in diameters gives a measurement of about 550 miles (880 kilometers) for the height of the X-ray absorbing region of Titan's atmosphere. The extent of the upper atmosphere is consistent with, or slightly (10-15%) larger, than that implied by Voyager I observations made at radio, infrared, and ultraviolet wavelengths in 1980. "Saturn was about 5% closer to the Sun in 2003, so increased solar heating of Titan may account for some of this atmospheric expansion," said Hiroshi Tsunemi of Osaka University in Japan, one of the coauthors on the paper. The X-ray brightness and extent of the Crab Nebula made it possible to study the tiny X-ray shadow cast by Titan during its transit. By using Chandra to precisely track Titan's position, astronomers were able to measure a shadow one arcsecond in

Simulating the Transfer of Strontium-90 from Soil to Leafy Vegetables by Using Strontium-88

OpenAIRE

Kuke, Ding; Shujuan, Liu; Yingxue, He; Dong, Yan; Fengshou, Zhang; Shuifeng, Wang; Jinghua, Guo; Wei, Zhang; Xin, Wang; Xiaoyan, Jiang

2016-01-01

The transfer, from soil to Chinese cabbage and spinach, of radioactive strontium-90 released as a result of accidents in nuclear power stations was studied using a stable isotope of strontium, namely nuclide strontium-88 (88Sr). The study led to an experimental model for assessing the hazard of radionuclide strontium-90 (90Sr) entering the food chain and for predicting the risk to food safety. Chinese cabbage and spinach were grown in pots in a greenhouse and irrigated with deionized water co...

Role of glass structure in defining the chemical dissolution behavior, bioactivity and antioxidant properties of zinc and strontium co-doped alkali-free phosphosilicate glasses.

Science.gov (United States)

Kapoor, Saurabh; Goel, Ashutosh; Tilocca, Antonio; Dhuna, Vikram; Bhatia, Gaurav; Dhuna, Kshitija; Ferreira, José M F

2014-07-01

We investigated the structure-property relationships in a series of alkali-free phosphosilicate glass compositions co-doped with Zn(2+) and Sr(2+). The emphasis was laid on understanding the structural role of Sr(2+) and Zn(2+) co-doping on the chemical dissolution behavior of glasses and its impact on their in vitro bioactivity. The structure of glasses was studied using molecular dynamics simulations in combination with solid state nuclear magnetic resonance spectroscopy. The relevant structural properties are then linked to the observed degradation behavior, in vitro bioactivity, osteoblast proliferation and oxidative stress levels. The apatite-forming ability of glasses has been investigated by X-ray diffraction, infrared spectroscopy and scanning electron microscopy-energy-dispersive spectroscopy after immersion of glass powders/bulk in simulated body fluid (SBF) for time durations varying between 1h and 14 days, while their chemical degradation has been studied in Tris-HCl in accordance with ISO 10993-14. All the glasses exhibit hydroxyapatite formation on their surface within 1-3h of their immersion in SBF. The cellular responses were observed in vitro on bulk glass samples using human osteosarcoma MG63 cell line. The dose-dependent cytoprotective effect of glasses with respect to the concentration of zinc and strontium released from the glasses is also discussed. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Neodymium-doped Sr5(PO4)3F and Sr5(VO4)3F

International Nuclear Information System (INIS)

Corker, D.L.; Nicholls, J.; Loutts, G.B.

1995-01-01

Neodymium-doped Sr 5 (PO 4 ) 3 F [neodymium strontium fluoride phosphate, (Nd,Sr) 5 (PO 4 ) 3 F] and neodymium-doped Sr 5 (VO 4 ) 3 F [neodymium strontium fluoride vanadate, (Nd,Sr) 5 (VO 4 ) 3 F] crystallize in space group P6 3 /m and are isostructural with calcium fluorophosphate, Ca 5 (PO 4 ) 3 F. There are two different Sr sites in Sr 5 (XO 4 ) 3 F, denoted Sr(1) and Sr(2). Using single-crystal X-ray diffraction the two structures were refined to R factors of 2.3 and 2.2%, respectively, showing that Nd is present at both Sr sites in (Sr,Nd) 5 (VO 4 ) 3 F but only at the Sr(2) site in (Sr,Nd) 5 (PO 4 ) 3 F. (orig.)

Strontium-82/rubidium-82 generator

International Nuclear Information System (INIS)

Gennaro, G.P.; Haney, P.S.

1986-01-01

Hydroxylapatite, a compound having the formula: M 10 (PO 4 ) 6 (OH) 2 wherein M is calcium, strontium, barium, lead, iron, sodium, potassium, zinc, cadmium, magnesium, aluminium or a rare earth metal, is provided as a support medium for strontium-82 in a strontium-82/rubidium-82 parent-daughter radionuclide generator

Strontium doping promotes bioactivity of rhBMP-2 upon calcium phosphate cement via elevated recognition and expression of BMPR-IA.

Science.gov (United States)

Huang, Baolin; Tian, Yu; Zhang, Wenjing; Ma, Yifan; Yuan, Yuan; Liu, Changsheng

2017-11-01

Preserving and improving osteogenic activity of bone morphogenetic protein-2 (BMP-2) upon implants remains one of the key limitations in bone regeneration. With calcium phosphate cement (CPC) as model, we have developed a series of strontium (Sr)-doped CPC (SCPC) to address this issue. The effects of fixed Sr on the bioactivity of recombinant human BMP-2 (rhBMP-2) as well as the underlying mechanism were investigated. The results suggested that the rhBMP-2-induced osteogenic activity was significantly promoted upon SCPCs, especially with a low amount of fixed Sr (SrCO 3 content IA (BMPR-IA) to rhBMP-2 and an increased expression of BMPR-IA in C2C12 model cells. As a result, the activations of BMP-induced signaling pathways were different in C2C12 cells incubated upon CPC/rhBMP-2 and SCPCs/rhBMP-2. These findings explicitly decipher the mechanism of SCPCs promoting osteogenic bioactivity of rhBMP-2 and signify the promising application of the SCPCs/rhBMP-2 matrix in bone regeneration implants. Copyright © 2017 Elsevier B.V. All rights reserved.

Mechanical niobium doping in barium titanate electroceramics

Energy Technology Data Exchange (ETDEWEB)

Velasco-Davalos, I.A., E-mail: ivan.velascodavalos@gmail.com [Departmento de Ingeniería Metalúrgica, Instituto Politécnico Nacional, Zacatenco, 07338 México D.F. (Mexico); INRS-EMT, 1650 Boul. Lionel-Boulet, Varennes J3X 1S2 (Canada); Ruediger, A. [INRS-EMT, 1650 Boul. Lionel-Boulet, Varennes J3X 1S2 (Canada); Cruz-Rivera, J.J. [Universidad Autónoma de San Luis Potosí, Av. Sierra Leona 550, Lomas, 78210 S.L.P. (Mexico); Gomez-Yanez, C. [Departmento de Ingeniería Metalúrgica, Instituto Politécnico Nacional, Zacatenco, 07338 México D.F. (Mexico)

2013-12-25

Highlights: •We demonstrate a new doping procedure by Mechanical Alloying (MA). •For small dopant concentrations, charge compensation of Nb is primarily attributed to free electrons. •At higher Nb concentrations cation vacancies prevail as compensation mechanism. -- Abstract: Niobium is a well-established donor dopant for semi-conducting BaTiO{sub 3} ceramics. The conventional procedure to dissolve Nb into BaTiO{sub 3} relies on thermal activation at high temperatures (up to 1500 °C) and even then, large dwell times are necessary due to the small diffusion coefficients of Nb{sup 5+}. In this work, we demonstrate a new doping procedure by Mechanical Alloying (MA), which has already proven its potential for the fabrication of conductive electroceramics. In a planetary mill, powders of BaTiO{sub 3} and Nb{sub 2}O{sub 5} were mixed for up to 540 min. The BaTiO{sub 3} unit cell volume increases with increasing Nb concentration. The electrical properties of conventional and mechanical alloyed samples as a function of Nb concentration are similar, however the mechanically alloyed samples shows a large conductivity that we attribute to a better homogeneity in the structure of MA-processed samples. For small dopant concentrations, charge compensation of the pentavalent Nb is primarily attributed to free electrons. At higher Nb concentrations cation vacancies prevail as compensation mechanism.

Sintering and electrical properties of strontium-doped lanthanum manganite

Energy Technology Data Exchange (ETDEWEB)

Tarrago, Diego Pereira; Sousa, Vania Caldas de [Universidade Federal do Rio Grande do Sul (LABIOMAT/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Biomateriais], Email: dptarrago@gmail.com; Moreno Buriel, Berta; Chinarro Martini, Eva; Jurado Egea, Jose Ramon [Consejo Superior de Investigaciones Cientificas (ICV/CSIC), Madrid (Spain). Inst. de Ceramica y Vidrio; Malfatti, Celia de Fraga [Universidade Federal do Rio Grande do Sul (LAPEC/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Pesquisa em Corrosao

2010-07-01

Lanthanum strontium manganites (LSM) are potential materials for cathode applications in solid oxide fuel cells (SOFC) due to their good catalytic activity, chemical stability and compatibility with electrolyte materials in high temperatures. The sinterability of single phase La{sub 1-x}Sr{sub x}Mn{sub O3} (x=0.18) perovskite powders and the electrical properties of the resulting samples are analyzed in this study. Using a heating microscope, the powders were pressed and sintered at different pressures and temperatures, resulting in an open porosity of 33.36% when compacted at 125 MPa and sintered at 1200 degree C. Top and cross-section s canning electron microscopy (SEM) micrographs revealed interconnected pores in the sintered body and, hence, a suitable microstructure for the application. The activation energy for conductance was 0.04 eV and the tested LSM bulk started to exhibit adequate electrical properties at about 500 degree C. (author)

Photocatalysis of Yttrium Doped BaTiO3 Nanofibres Synthesized by Electrospinning

Directory of Open Access Journals (Sweden)

Zhenjiang Shen

2015-01-01

Full Text Available Yttrium doped barium titanate (BT nanofibres (NFs with significant photocatalytic effect were successfully synthesized by electrospinning. Considering the necessary factors for semiconductor photocatalysts, a well-designed procedure was carried out to produce yttrium doped BT (BYT NFs. In contrast to BYT ceramics powders and BT NFs, BYT NFs with pure perovskite phase showed much enhanced performance of photocatalysis. The surface modification in electrospinning and subsequent annealing, the surface spreading of transition metal yttrium, and the narrowed band gap energy in yttrium doping were all contributed to the final novel photocatalytic effect. This work provides a direct and efficient route to obtain doped NFs, which has a wide range of potential applications in areas based on complex compounds with specific surface and special doping effect.

Electrical characterization and impedance response of lanthanum doped barium titanate ceramics

Directory of Open Access Journals (Sweden)

Mančić D.

2008-01-01

Full Text Available The dielectric permittivity and dissipation factor of La-doped and undoped BaTiO3 were investigated as a function of frequency and temperature. The impedance response was used to study the electrical properties of La-doped BaTiO3 over the temperature range from room temperature (RT to 350°C. La-doped and undoped BaTiO3, obtained by a modified Pechini method, were sintered in air at 1300°C for 2 and 16 hours. The impedance spectra were analyzed in terms of equivalent circuits involving resistors, capacitors and constant phase elements (CPE. The most suitable electrical circuit for the interpretation of experimental results is found to be the equivalent circuit consisting of resistors and CPE elements which replace the capacitor elements. The contribution of grain boundary resistance to the total resistance of a system is remarkable at low temperature. Dielectric permittivity of doped BaTiO3 was in the range of 8000 to 12000 at 1 kHz and the dissipation factor was less than 1%.

Elaboration of strontium ruthenium oxide thin films on metal substrates by chemical solution deposition

International Nuclear Information System (INIS)

Seveno, R.; Braud, A.; Gundel, H.W.

2005-01-01

In order to improve the structural interface between a metal substrate and a lead zirconate titanate (Pb(ZrTi)O 3 , PZT) ferroelectric thin film, the elaboration of strontium ruthenium oxide (SrRuO 3 ) by chemical solution deposition is studied. The SrRuO 3 thin films were realized by multiple spin-coating technique and the temperature of the rapid thermal annealing process was optimized. The crystallization behavior was examined by X-ray diffraction; surface analyses using scanning electron microscope and atomic force microscope techniques showed the influence of the SrRuO 3 layer at the interface PZT/metal on the morphology of the ferroelectric thin film. From the electrical measurements, a coercive electric field around 25 kV/cm and a remanent polarization of approximately 30 μC/cm were found

Magnetic and electromagnetic properties of Pr doped strontium ferrite/polyaniline composite film

Energy Technology Data Exchange (ETDEWEB)

Huang, Ying; Li, Yuqing; Wang, Yan, E-mail: wangyan287580632@126.com

2014-11-15

This paper reported three acid (including hydrochloric acid HCl, p-toluenesulfonic acid PTS and D-camphor-10-acid CSA) doped SrPr{sub 0.2}Fe{sub 11.8}O{sub 19}/PANI composite film and the HCl–PANI film prepared by a sol–gel method and in-situ oxidative polymerization. The characteristics of the film phase structure, surface morphology, conductivity and magnetic and electromagnetic properties were studied by using XRD, XPS, FESEM, four-probe tester, VSM and Vector Network Analyzer. The resistivity of organic acid doped composite films is higher than that of the HCl doped one. The saturation and remanent magnetization of PTS and HCl doped composite films are greater than the CSA-doped one; however, the coercivity of the three acid doped composite films is basically 5546 Oe. The saturation magnetization, remanent magnetization and coercivity of SrPr{sub 0.2}Fe{sub 11.8}O{sub 19} film are greater than those of the SrPr{sub 0.2}Fe{sub 11.8}O{sub 19}–PANI composite film. In the frequency range of 8–12 GHz, the dielectric loss of HCl–PANI film is the maximum, and the dielectric loss of SrPr{sub 0.2}Fe{sub 11.8}O{sub 19} film is the minimum; the magnetic loss of the four films is in descending order as SrPr{sub 0.2}Fe{sub 11.8}O{sub 19} film, PrSrM/(HCl–PANI) composite film, PrSrM/(CSA–PANI) and HCl–PANI film. - Highlights: • Synthesizing three acid doped SrPr{sub 0.2}Fe{sub 11.8}O{sub 19}/PANI composite films. • By sol–gel method and in-situ oxidative polymerization. • With excellent magnetic and electromagnetic properties. • The particular coating structure of PANI and Sr-ferrite. • Great interest for magnetic material and microwave absorbers.

Trivalent europium-doped strontium molybdate red phosphors in white light-emitting diodes: Synthesis, photophysical properties and theoretical calculations

International Nuclear Information System (INIS)

Yang, W.-Q.; Liu, H.-G.; Liu, G.-K.; Lin, Y.; Gao, M.; Zhao, X.-Y.; Zheng, W.-C.; Chen, Y.; Xu, J.; Li, L.-Z.

2012-01-01

Eu 3+ -doped strontium molybdate red phosphors (Sr 1−x MoO 4 :Eu x (x = 0.01–0.2)) for white light-emitting diodes (LED) were synthesized by the solid-state reaction method. The fluorescent intensities of the as-prepared phosphors were remarkably improved. The excitation and emission spectra demonstrate that these phosphors can be effectively excited by the near-UV light (395 nm) and blue light (466 nm). Their emitted red light peaks are located at 613 nm, and the highest quantum yield value (η) of the as-grown red phosphor, which is 95.85%, is much higher than that of commercial red phosphor (77.53%). These red phosphors plus commercial yellow powers (1:10) were successfully packaged with the GaN-based blue chips on a piranha frame by epoxy resins. The encapsulated white LED lamps show high performance of the CIE chromaticity coordinates and color temperatures. Moreover, to explain the fluorescent spectra of these phosphors, a complete 3003 × 3003 energy matrix was successfully built by an effective operator Hamiltonian including free ion and crystal field interactions. For the first time, the fluorescent spectra for Eu 3+ ion at the tetragonal (S 4 ) Sr 2+ site of SrMoO 4 crystal were calculated from a complete diagonalization (of energy matrix) method. The fitting values are close to the experimental results.

Combined transuranic-strontium extraction process

Science.gov (United States)

Horwitz, E. Philip; Dietz, Mark L.

1992-01-01

The transuranic (TRU) elements neptunium, plutonium and americium can be separated together with strontium from nitric acid waste solutions in a single process. An extractant solution of a crown ether and an alkyl(phenyl)-N,N-dialkylcarbanylmethylphosphine oxide in an appropriate diluent will extract the TRU's together with strontium, uranium and technetium. The TRU's and the strontium can then be selectively stripped from the extractant for disposal.

Visible-light photochemical activity of heterostructured core-shell materials composed of selected ternary titanates and ferrites coated by tiO2.

Science.gov (United States)

Li, Li; Liu, Xuan; Zhang, Yiling; Nuhfer, Noel T; Barmak, Katayun; Salvador, Paul A; Rohrer, Gregory S

2013-06-12

Heterostructured photocatalysts comprised of microcrystalline (mc-) cores and nanostructured (ns-) shells were prepared by the sol-gel method. The ability of titania-coated ATiO3 (A = Fe, Pb) and AFeO3 (A = Bi, La, Y) catalysts to degrade methylene blue in visible light (λ > 420 nm) was compared. The catalysts with the titanate cores had enhanced photocatalytic activities for methylene blue degradation compared to their components alone, whereas the catalysts with ferrite cores did not. The temperature at which the ns-titania shell is crystallized influences the photocatalytic dye degradation. mc-FeTiO3/ns-TiO2 annealed at 500 °C shows the highest reaction rate. Fe-doped TiO2, which absorbs visible light, did not show enhanced photocatalytic activity for methylene blue degradation. This result indicates that iron contamination is not a decisive factor in the reduced reactivity of the titania coated ferrite catalysts. The higher reactivity of materials with the titanate cores suggests that photogenerated charge carriers are more easily transported across the titanate-titanate interface than the ferrite-titanate interface and this provides guidance for materials selection in composite catalyst design.

Innovative Highly Selective Removal of Cesium and Strontium Utilizing a Newly Developed Class of Inorganic Ion Specific Media - 16221

International Nuclear Information System (INIS)

Denton, Mark S.; Kanatzidis, Mercouri G.

2009-01-01

Highly selective removal of Cesium and Strontium is critical for waste treatment and environmental remediation. Cesium-137 is a beta-gamma emitter and Strontium-90 is a beta emitter with respective half-lives of 30 and 29 years. Both elements are present at many nuclear sites. Cesium and Strontium can be found in wastewaters at Washington State's Hanford Site, as well as in waste streams of many Magnox reactor sites. Cesium and Strontium are found in the Reactor Coolant System of light water reactors at nuclear power plants. Both elements are also found in spent nuclear fuel and in high-level waste (HLW) at DOE sites. Cesium and Strontium are further major contributors to the activity and the heat load. Therefore, technologies to extract Cesium and Strontium are critical for environmental remediation waste treatment and dose minimization. Radionuclides such as Cesium-137 and Strontium-90 are key drivers of liquid waste classification at light water reactors and within the DOE tank farm complexes. The treatment, storage, and disposal of these wastes represents a major cost for nuclear power plant operators, and comprises one of the most challenging technology-driven projects for the DOE Environmental Management (EM) program. Extraction technologies to remove Cesium and Strontium have been an active field of research. Four notable extraction technologies have been developed so far for HLW: solvent extraction, prussian blue, crystalline silico-titanate (CST) and organic ion-exchangers (e.g., resorcinol formaldehyde and SuperLig). The use of one technology over another depends on the specific application. For example, the waste treatment plant (WTP) at Hanford is planning on using a highly-selective organic ion-exchange resin to remove Cesium and Strontium. Such organic ion-exchangers use molecular recognition to selectively bind to Cesium and Strontium. However, these organic ion-exchangers are synthesized using multi-step organic synthesis. The associated cost to

Titan Aerial Daughtercraft

Data.gov (United States)

National Aeronautics and Space Administration — Saturn's giant moon Titan has become one of the most fascinating bodies in the Solar System. Titan is the richest laboratory in the solar system for studying...

TAILORING INORGANIC SORBENTS FOR SRS STRONTIUM AND ACTINIDE SEPARATIONS: MODIFIED MONOSODIUM TITANATE PHASE III FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Taylor-Pashow, K.; Hobbs, D.

2010-09-01

This document provides a final report of Phase III testing activities for the development of modified monosodium titanate (mMST), which exhibits improved strontium and actinide removal characteristics compared to the baseline MST material. The activities included characterization of the crystalline phases present at varying temperatures, solids settling characteristics, quantification of the peroxide content; evaluation of the post-synthesis gas release under different conditions; the extent of desorption of {sup 85}Sr, Np, and Pu under washing conditions; and the effects of age and radiation on the performance of the mMST. Key findings and conclusions include the following. The peroxide content of several mMST samples was determined using iodometric titration. The peroxide content was found to decrease with age or upon extended exposure to elevated temperature. A loss of peroxide was also measured after exposure of the material to an alkaline salt solution similar in composition to the simulated waste solution. To determine if the loss of peroxide with age affects the performance of the material, Sr and actinide removal tests were conducted with samples of varying age. The oldest sample (4 years and 8 months) did show lower Sr and Pu removal performance. When compared to the youngest sample tested (1 month), the oldest sample retained only 15% of the DF for Pu. Previous testing with this sample indicated no decrease in Pu removal performance up to an age of 30 months. No loss in Np removal performance was observed for any of the aged samples, and no uptake of uranium occurred at the typical sorbent loading of 0.2 g/L. Additional testing with a uranium only simulant and higher mMST loading (3.0 g/L) indicated a 10% increase of uranium uptake for a sample aged 3 years and 8 months when compared to the results of the same sample measured at an age of 1 year and 5 months. Performance testing with both baseline-MST and mMST that had been irradiated in a gamma source to

Strontium (Sr) separation from seawater using titanate adsorbents: Effects of seawater matrix ions on Sr sorption behavior

Science.gov (United States)

Ryu, Jungho; Hong, Hye-jin; Ryu, Taegong; Park, In-Su

2017-04-01

Strontium (Sr) which has many industrial applications such as ferrite magnet, ceramic, and fire works exists in seawater with the concentration of approximately 7 mg/L. In previous report estimating economic potential on recovery of various elements from seawater in terms of their commercial values and concentrations in seawater, Sr locates upper than approximate break-even line, which implies Sr recovery from seawater can be potentially profitable. Recently, Sr separation from seawater has received great attention in the environmental aspect after Fukushima Nuclear Power Plant (NPP) accident which released much amount of radioactive Sr and Cs. Accordingly, the efficient separation of radioactive elements released to seawater has become critical as an important technological need as well as their removal from radioactive wastes. So far, it has been introduced to separate Sr from aqueous media by various methods including solvent extraction, adsorption by solid materials, and ion exchange. Among them, the adsorption technique using solid adsorbents is of great interest for selectively separating Sr from seawater with respect to low concentration level of Sr. In this study, we synthesized titanate nanotube (TiNT) by simple hydrothermal reaction, characterized its physicochemical properties, and systematically evaluated Sr sorption behavior under various reaction conditions corresponding to seawater environment. The synthesized TiNT exhibited the fibril-type nanotube structure with high specific surface area of 260 m2/g. The adsorption of Sr on TiNT rapidly occurred following pseudo-second-order kinetic model, and was in good agreement with Langmuir isotherm model, indicating maximum adsorption capacity of 97 mg/g. Based on Sr uptake and Na release with stoichiometric balance, sorption mechanism of Sr on TiNT was found to be ion-exchange between Na in TiNT lattice and Sr in solution phase, which was also confirmed by XRD and Raman analysis. Among competitive ions, Ca

The PILO process: zeolites and titanates in the treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Hultgren, Aa.; Thegerstroem, C.; Forberg, S.; Westermark, T.; Faelt, L.

1981-01-01

Spent ion exchange resins from power reactor operation contain more than 95% of the total radioactivity of wet reactor wastes. Cementation and bituminization are the two methods applied in Sweden up to now for the immobilization of spent resins. Over the last years, however, research and development work has resulted in a proposed process (PILO), where > 99.9 % of cesium and strontium and around 90 % of other radioactive nuclides are eluted from the spent resins and sorbed in zeolites and titanates in a chromatographic process. The inorganic sorbents are dried after loading and sintered to yield long-term stable products, while the treated resins may be incinerated to give ash residues of fairly short-lived activity. The development work has included production, characterization and testing of different zeolites and titanates, bench-scale optimization of the chromatographic process using actual spent resins, heat treatment of the loaded inorganic sorbents, and resin incineration. Over-all system design studies including transport requirements, integrated process flowsheets, and cost estimates are now in progress. The aim is to have a sufficient basis during spring 1982 to decide on the merits of a PILO plant at the planned repository for low and medium level waste (SFR), to be commissioned in 1988. (Auth.)

The effect of strontium and barium doping on perovskite-structured energy materials for photovoltaic applications

Science.gov (United States)

Wu, Ming-Chung; Chen, Wei-Cheng; Chan, Shun-Hsiang; Su, Wei-Fang

2018-01-01

Perovskite solar cell is a novel photovoltaic technology with the superior progress in efficiency and the simple solution processes. Develop lead-free or lead-reduced perovskite materials is a significant concern for high-performance perovskite solar cell. Among the alkaline earth metals, the Sr2+ and Ba2+ are suitable for Pb2+ replacement in perovskite film due to fitting Goldschmidt's tolerance factor. In this study, we adopted Ba-doped and Sr-doped perovskite structured materials with different doping levels, including 1.0, 5.0, and 10.0 mol%, to prepare perovskite solar cells. Both Ba-doped and Sr-doped perovskite structured materials have a related tendency in absorption behavior and surface morphology. At 10.0 mol% doping level, the power conversion efficiency (PCE) of Sr-doped perovskite solar cells is only ∼0.5%, but the PCE of Ba-doped perovskite solar cells can be achieved to ∼9.7%. Ba-doped perovskite solar cells showed the acceptable photovoltaic characteristics than Sr-doped perovskite solar cells. Ba dopant can partially replace the amount of lead in the perovskite solar cells, and it could be a potential candidate in the field of lead-free or lead-reduced perovskite energy materials.

Phase stability and processing of strontium and magnesium doped lanthanum gallate

Science.gov (United States)

Zheng, Feng

Fuel Cells are one of the most promising energy transformers with respect to ecological and environmental issues. Solid Oxide Fuel Cells (SOFC) are all solid-state devices. One of the challenges to improve a SOFC is to lower the operating temperature while maintaining or increasing its output voltage. Undoped LaGaO3 is an insulator, doping transforms it into an oxygen-ionic conductor. Sr and Mg doped LaGaO3 (LSGM) perovskite is a new oxygen-ionic conductor with higher conductivity than yttria-stabilized zirconia (YSZ). This material is a candidate for a wide variety of electrochemical devices. In order to realize this potential, the phase stability and processing of this material needs to be investigated in detail. In this study, a systematic investigation of the LSGM materials in terms of phase stability, phase transition, sintering, microstructure and electrical conductivity as functions of temperature, doping content and A/B cation ratio has been carried out. The generalized formula of the materials investigated is (La1--xSrx)A(Ga1--yMg y)BO3--delta. Optimized processing parameters have been obtained by investigating their impact on density change and microstructure. Consequently, a suitable compositional window of the LSGM perovskite has been identified for SOFC electrolyte applications. Based on detailed diffraction analysis, it is found that the undoped LaGaO3 takes on the orthorhombic (Pbnm) symmetry at room temperature. This structure changes to rhombohedral (R3c) at 147 +/- 2°C or changes to monoclinic (I2/a) when the doping level increases from 0.1 to 0.2 moles. We have optimized the compositional window to make the single perovskite phase with high oxygen ionic conductivity (x = 0.10 to 0.20 with A/B ratio between 0.98 to 1.02). The best processing condition, starting from glycine nitrate process (GNP) combustion synthesized ultra-fine LSGM powder, is sintering in air at 1500°C for 2 hours. The doped material has higher oxygen ionic conductivity than

Deposition of strontium and calcium in snail shell

Energy Technology Data Exchange (ETDEWEB)

Rosenthal, Jr, G M; Nelson, D J; Gardiner, D A

1965-07-03

The relative effects of strontium and calcium concentrations in the environment on their uptake and incorporation into snail shell were investigated. /sup 45/Ca and /sup 85/Sr were used as tracers and specific activities were used to determine deposition. Data are presented in tables and graphs. Deposition of both calcium and strontium in the snail shell depended primarily on the respective concentrations of these elements in the immediate environment. A slight effect of strontium on calcium deposition was observed. There was found to be a minimum strontium deposition for various combinations of strontium and calcium in the environment. It was concluded that strontium uptake is more closely associated with environmental strontium concentrations than with calcium concentrations.

Tailoring structure and magnetic characteristics of strontium hexaferrite via Al doping engineering

Energy Technology Data Exchange (ETDEWEB)

Wang, H.Z.; Hai, Y.N. [State Key Lab of High Power Semiconductor Laser of Changchun University Science and Technology, Changchun University Science and Technology, Changchun 130022 (China); Yao, B., E-mail: binyao@jlu.edu.cn [State Key Lab of Superhard Materials and Department of Physics, Jilin University, Changchun 130023 (China); Xu, Y. [School of Physics, Northeast Normal University, Changchun 130024 (China); Shan, L. [State Key Laboratory of Inorganic Synthesis and Preparative Chemistry and Department of Chemistry, Jilin University, Changchun 130012 (China); Xu, L.; Tang, J.L.; Wang, Q.H. [State Key Lab of High Power Semiconductor Laser of Changchun University Science and Technology, Changchun University Science and Technology, Changchun 130022 (China)

2017-01-15

Emerging structure and magnetic properties of Al{sup 3+}-modified SrFe{sub 12}O{sub 19} M-type hexaferrite system (SrAl{sub x}Fe{sub 12−x}O{sub 19}) had been studied in detail via doping engineering. With Al{sup 3+} ion nominal content ranging from 0 to 4 (0≤x≤4), the lattice parameters decrease due to the substitution of Fe{sup 3+} ions by smaller Al{sup 3+} ions, and the magnetization shows a continuous reduction with the increasing of Al content. For the coercivity, its value initially increases, reaching a maximum value of 16,876.9 Oe at x=3, and then reduces with the Al content further increase. When all the Fe{sup 3+} ions (x=4) are replaced by Al{sup 3+} ions, the net magnetic moment will be closed to zero, that will weaken the exchange interaction between Fe{sup 3+} ions, resulting in decrease of coercivity sharply and transformation ferrimagnetism into antiferromagnetism. The mechanism of the improvement of the magnetic properties induced by Al doping is discussed in the present work. - Highlights: • The coercivity reach a maximum value at x=3 in the SrAl{sub x}Fe{sub 12−x}O{sub 19}. • The coercivity of SrFe{sub 12}O{sub 19} increases due to nonmagnetic Al doping. • The saturation magnetization of SrFe{sub 12}O{sub 19} decreases due to nonmagnetic Al doping. • The transformation ferrimagnetism into antiferromagnetism by nonmagnetic Al doping.

Elaboration of strontium ruthenium oxide thin films on metal substrates by chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Seveno, R. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France)]. E-mail: raynald.seveno@univ-nantes.fr; Braud, A. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France); Gundel, H.W. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France)

2005-12-22

In order to improve the structural interface between a metal substrate and a lead zirconate titanate (Pb(ZrTi)O{sub 3}, PZT) ferroelectric thin film, the elaboration of strontium ruthenium oxide (SrRuO{sub 3}) by chemical solution deposition is studied. The SrRuO{sub 3} thin films were realized by multiple spin-coating technique and the temperature of the rapid thermal annealing process was optimized. The crystallization behavior was examined by X-ray diffraction; surface analyses using scanning electron microscope and atomic force microscope techniques showed the influence of the SrRuO{sub 3} layer at the interface PZT/metal on the morphology of the ferroelectric thin film. From the electrical measurements, a coercive electric field around 25 kV/cm and a remanent polarization of approximately 30 {mu}C/cm were found.

Structural and magnetic properties of single-crystalline Co-doped barium titanate nanoparticles

International Nuclear Information System (INIS)

Liu Hongxue; Cao Baobao; O'Connor, Charles J.

2010-01-01

Undoped and Co-doped BaTiO 3 nanoparticles were synthesized by a one-step sol-precipitation method. For all the samples, X-ray diffraction showed characteristic diffraction lines for BaTiO 3 without the indication of secondary phases. High-resolution transition electron microscopy images showed that BaTiO 3 nanoparticles exhibit the nature of single-crystal. Magnetometry revealed that all the Co-doped BaTiO 3 samples show paramagnetic behaviors and Co ions in BaTiO 3 are present as isolated paramagnetic centers. This is contrasted to several reported cases of ferromagnetism in Co-doped BaTiO 3 .

KAJIAN SIFAT OPTIK FILM TIPIS BST DIDADAH NIOBIUM DAN TANTALUM

Directory of Open Access Journals (Sweden)

Farida Huriawati

2016-11-01

Full Text Available In this research thin films of Barium Strontium Titanate (BST has been synthesis with different compositions Ba0,5Sr0,5TiO3 and Ba0,25Sr0,75TiO3 which doped by Nb2O5 (Niobium and Ta2O5 (Tantalum on Si (100 type-p substrate. Thin films were produced by chemical solution deposition technique (CSD and spin coating technique with annealing temperature at 850oC, 900oC dan 950oC. Rotation velocity at 3000 rpm and time of rotation is 30 seconds. Characterization of Films is optic Characterization (absorbance ana reflectance. From the Characterizations were obtained BNST thin film with 5% doping and anneling temperature at 8500C as photodiode light sensor which applied in electronic circuit.

The TITAN reversed-field-pinch fusion reactor study

International Nuclear Information System (INIS)

1990-01-01

This report discusses the following topics: overview of titan-2 design; titan-2 fusion-power-core engineering; titan-2 divertor engineering; titan-2 tritium systems; titan-2 safety design and radioactive-waste disposal; and titan-2 maintenance procedures

The TITAN reversed-field-pinch fusion reactor study

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

This report discusses the following topics: overview of titan-2 design; titan-2 fusion-power-core engineering; titan-2 divertor engineering; titan-2 tritium systems; titan-2 safety design and radioactive-waste disposal; and titan-2 maintenance procedures.

Titan's organic chemistry

Science.gov (United States)

Sagan, C.; Thompson, W. R.; Khare, B. N.

1985-01-01

Voyager discovered nine simple organic molecules in the atmosphere of Titan. Complex organic solids, called tholins, produced by irradiation of the simulated Titanian atmosphere, are consistent with measured properties of Titan from ultraviolet to microwave frequencies and are the likely main constituents of the observed red aerosols. The tholins contain many of the organic building blocks central to life on earth. At least 100-m, and possibly kms thicknesses of complex organics have been produced on Titan during the age of the solar system, and may exist today as submarine deposits beneath an extensive ocean of simple hydrocarbons.

Giant energy density and high efficiency achieved in bismuth ferrite-based film capacitors via domain engineering.

Science.gov (United States)

Pan, Hao; Ma, Jing; Ma, Ji; Zhang, Qinghua; Liu, Xiaozhi; Guan, Bo; Gu, Lin; Zhang, Xin; Zhang, Yu-Jun; Li, Liangliang; Shen, Yang; Lin, Yuan-Hua; Nan, Ce-Wen

2018-05-08

Developing high-performance film dielectrics for capacitive energy storage has been a great challenge for modern electrical devices. Despite good results obtained in lead titanate-based dielectrics, lead-free alternatives are strongly desirable due to environmental concerns. Here we demonstrate that giant energy densities of ~70 J cm -3 , together with high efficiency as well as excellent cycling and thermal stability, can be achieved in lead-free bismuth ferrite-strontium titanate solid-solution films through domain engineering. It is revealed that the incorporation of strontium titanate transforms the ferroelectric micro-domains of bismuth ferrite into highly-dynamic polar nano-regions, resulting in a ferroelectric to relaxor-ferroelectric transition with concurrently improved energy density and efficiency. Additionally, the introduction of strontium titanate greatly improves the electrical insulation and breakdown strength of the films by suppressing the formation of oxygen vacancies. This work opens up a feasible and propagable route, i.e., domain engineering, to systematically develop new lead-free dielectrics for energy storage.

A green synthesis of a layered titanate, potassium lithium titanate; lower temperature solid-state reaction and improved materials performance

International Nuclear Information System (INIS)

Ogawa, Makoto; Morita, Masashi; Igarashi, Shota; Sato, Soh

2013-01-01

A layered titanate, potassium lithium titanate, with the size range from 0.1 to 30 µm was prepared to show the effects of the particle size on the materials performance. The potassium lithium titanate was prepared by solid-state reaction as reported previously, where the reaction temperature was varied. The reported temperature for the titanate preparation was higher than 800 °C, though 600 °C is good enough to obtain single-phase potassium lithium titanate. The lower temperature synthesis is cost effective and the product exhibit better performance as photocatalysts due to surface reactivity. - Graphical abstract: Finite particle of a layered titanate, potassium lithium titanate, was prepared by solid-state reaction at lower temperature to show modified materials performance. Display Omitted - Highlights: • Potassium lithium titanate was prepared by solid-state reaction. • Lower temperature reaction resulted in smaller sized particles of titanate. • 600 °C was good enough to obtain single phased potassium lithium titanate. • The product exhibited better performance as photocatalyst

Determination of radioactive strontium in seawater

International Nuclear Information System (INIS)

Grahek, Zeljko; Rozmaric Macefat, Martina

2005-01-01

This paper describes the procedures of isolating strontium and yttrium from seawater that enable the determination of 89,90 Sr. In one procedure, strontium is directly isolated from seawater on the column filled with Sr resin by binding of strontium to the resin from 3 M HNO 3 in a seawater, and successive elution with HNO 3 . In others, strontium is precipitated from seawater with (NH 4 ) 2 CO 3 , followed by isolation on a Sr column or an anion exchange column. It is shown that strontium precipitation is optimal with concentration of 0.3 M (NH 4 ) 2 CO 3 at pH = 11. In these conditions, 100% Y, 78% Sr, 80% Ca and 50% Mg are precipitated. Strontium is bound on to Sr column from 5 to 8 M HNO 3 , separated from other elements by elution with 3 M HNO 3 and 0.05 M HNO 3 . Strontium and yttrium are bound on to anion exchange column from alcoholic solutions of nitric acid. The optimum mixture of alcohols for sample binding is a mixture of ethanol and methanol with the volume ratio 1:3. Strontium and yttrium are separated from Mg, Ca, K, and other elements by elution with 0.25 M HNO 3 in the mixture of ethanol and methanol. After the separation, yttrium and strontium are eluted from the column with water or methanol. In the procedure of direct isolation from 1 l of the sample, the average recovery of 50% was obtained. In the remaining two procedures, the strontium recovery was about 60% for the Sr column and 65% for anion exchange column. Recovery of yttrium is about 70% for the anion exchange column. It turned out that the procedure with the Sr resin (direct isolation and isolation after precipitation) is simpler and faster in the phase of the isolation on the column in comparison with the procedure with the anion exchanger. The procedure with the anion exchanger, however, enables the simultaneous isolation of yttrium and strontium and rapid determination of 89,90 Sr. These procedures were tested by determination of 89,90 Sr on liquid scintillation counter and Cherenkov

Phase I Technical Report for the Engineering of Monosodium Titanate

International Nuclear Information System (INIS)

NASH, CHARLES

2004-01-01

Monosodium titanate (MST) is an inorganic adsorbent that effectively removes strontium, plutonium, uranium, and other trace elements from alkaline salt supernate. Current plans use the MST in batch contact processes to treat Savannah River Site (SRS) waste solutions that require 90Sr and actinide removal to meet low level disposal criteria. More effective use of MST may be realized if the MST could be engineered into a form suitable for a continuous treatment process such as an adsorption column. The main benefits of column operation are (1) enhanced loading due to equilibration with feed adsorbate levels versus product levels, and (2) a small footprint relative to that of a batch contact tank. The current baseline MST material features particles of nominally 0.5-35 micron in size, which are much too fine for use in an adsorption column. An extensive review of the literature and consultation with technical experts identified candidate methods to produce engineered forms of MST. From this list a review team selected five candidate methods for further study. Laboratory syntheses at Savannah River National Laboratory (SRNL) and offsite produced representative samples for characterization and performance testing. Testing identified two suitable methods. The two methods include internal gelation, which is patented technology of Oak Ridge National Laboratory, and internal hydrolysis, a method in which the MST is produced within a porous substrate. A commercial sodium titanate, SrTreat(R), produced by Fortum Engineering (Finland), demonstrated good performance as well although plutonium removal kinetics appeared much slower than observed for the other engineered MST materials

Removal of Strontium from Drinking Water by Conventional ...

Science.gov (United States)

The United States Environmental Protection Agency Contaminant Candidate List 3 lists strontium as a contaminant for potential regulatory consideration in drinking water. There is very little data available on strontium removal from drinking water. As a result, there is an immediate need to perform treatment studies. The objective of this work is to evaluate the effectiveness of conventional and lime-soda ash softening treatments to remove strontium from surface and ground waters. Conventional drinking water treatment with aluminum and iron coagulants were able to achieve 12% and 5.9% strontium removal at best, while lime softening removed as much as 78% from natural strontium-containing ground water. Systematic fundamental experiments showed that strontium removal during the lime-soda ash softening was related to pH, calcium concentration and dissolved inorganic carbon concentration. Final strontium concentration was also directly associated with initial strontium concentration. Precipitated solids showed well-formed crystals or agglomerates of mixed solids, two polymorphs of calcium carbonate (vaterite and calcite), and strontianite, depending on initial water quality conditions. X-ray diffraction analysis suggested that strontium likely replaced calcium inside the crystal lattice and was likely mainly responsible for removal during lime softening. To inform the public.

The TITAN reversed-field-pinch fusion reactor study

International Nuclear Information System (INIS)

1990-01-01

This report discusses research on the titan-1 fusion power core. The major topics covered are: titan-1 fusion-power-core engineering; titan-1 divertor engineering; titan-1 tritium systems; titan-1 safety design and radioactive-waste disposal; and titan-1 maintenance procedures

The TITAN reversed-field-pinch fusion reactor study

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

This report discusses research on the titan-1 fusion power core. The major topics covered are: titan-1 fusion-power-core engineering; titan-1 divertor engineering; titan-1 tritium systems; titan-1 safety design and radioactive-waste disposal; and titan-1 maintenance procedures.

Strontium-90 fluoride data sheet

Energy Technology Data Exchange (ETDEWEB)

Fullam, H.T.

1981-06-01

This report is a compilation of available data and appropriate literature references on the properties of strontium-90 fluoride and nonradioactive strontium fluoride. The objective of the document is to compile in a single source pertinent data to assist potential users in the development, licensing, and use of /sup 90/SrF/sub 2/-fueled radioisotope heat sources for terrestrial power conversion and thermal applications. The report is an update of the Strontium-90 Fluoride Data Sheet (BNWL-2284) originally issued in April 1977.

The influences of mole composition of strontium (x) on properties of barium strontium titanate (Ba{sub 1−x}Sr{sub x}TiO{sub 3}) prepared by solid state reaction method

Energy Technology Data Exchange (ETDEWEB)

Sandi, Dianisa Khoirum; Supriyanto, Agus; Iriani, Yofentina, E-mail: yopen-2005@yahoo.com [Physics Department, Faculty of Mathematics and Natural Science, Sebelas Maret University (Indonesia); Jamaluddin, Anif [Physics Department, Faculty of Teacher Training and Education, Sebelas Maret University (Indonesia)

2016-02-08

Barium Strontium Titanate (Ba{sub 1-x}Sr{sub x}TiO{sub 3}) or BST was prepared by solid state reaction method. Raw materials are BaCO{sub 3}, SrCO{sub 3}, and TiO{sub 2}. Those materials are mixed for 8 h, pressed, and sintered at temperature 1200°C for 2 h. Mole composition of Sr (x) was varied to study its influences on structural, morphological, and electrical properties of BST. Variation of (x) are x = 0; x = 0.1; and x = 0.5. XRD patterns showed a single phase of BST, which mean that mixture of raw materials was homogenous. Crystal structure was influenced by x. BaTiO{sub 3} and Ba{sub 0.9}Ti{sub 0.1}TiO{sub 3} have tetragonal crystal structure, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is cubic. The diffraction angle shifted to right side (angle larger) as the increases of x. Crystalline size of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3}, and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} are 38.13 nm; 38.62 nm; and 37.13 nm, respectively. SEM images showed that there are still of pores which were influenced by x. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface (pores are few and small in size). Sawyer Tower circuit showed that BaTiO{sub 3} and Ba{sub 0.9}Sr{sub 0.1} TiO{sub 3} is ferroelectric, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is paraelectric. The dielectric constants of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} at frequency of 1 KHz are 156; 196; and 83, respectively. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has relatively highest dielectric constant. It is considered that Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface.

Titan's Methane Cycle is Closed

Science.gov (United States)

Hofgartner, J. D.; Lunine, J. I.

2013-12-01

Doppler tracking of the Cassini spacecraft determined a polar moment of inertia for Titan of 0.34 (Iess et al., 2010, Science, 327, 1367). Assuming hydrostatic equilibrium, one interpretation is that Titan's silicate core is partially hydrated (Castillo-Rogez and Lunine, 2010, Geophys. Res. Lett., 37, L20205). These authors point out that for the core to have avoided complete thermal dehydration to the present day, at least 30% of the potassium content of Titan must have leached into an overlying water ocean by the end of the core overturn. We calculate that for probable ammonia compositions of Titan's ocean (compositions with greater than 1% ammonia by weight), that this amount of potassium leaching is achievable via the substitution of ammonium for potassium during the hydration epoch. Formation of a hydrous core early in Titan's history by serpentinization results in the loss of one hydrogen molecule for every hydrating water molecule. We calculate that complete serpentinization of Titan's core corresponds to the release of more than enough hydrogen to reconstitute all of the methane atoms photolyzed throughout Titan's history. Insertion of molecular hydrogen by double occupancy into crustal clathrates provides a storage medium and an opportunity for ethane to be converted back to methane slowly over time--potentially completing a cycle that extends the lifetime of methane in Titan's surface atmosphere system by factors of several to an order of magnitude over the photochemically-calculated lifetime.

Understanding the defect chemistry of alkali metal strontium silicate solid solutions: insights from experiment and theory

KAUST Repository

Bayliss, Ryan D.; Cook, Stuart N.; Scanlon, David O.; Fearn, Sarah; Cabana, Jordi; Greaves, Colin; Kilner, John A.; Skinner, Stephen J.

2014-01-01

© the Partner Organisations 2014. Recent reports of remarkably high oxide ion conduction in a new family of strontium silicates have been challenged. It has recently been demonstrated that, in the nominally potassium substituted strontium germanium silicate material, the dominant charge carrier was not the oxygen ion, and furthermore that the material was not single phase (R. D. Bayliss et. al., Energy Environ. Sci., 2014, DOI: 10.1039/c4ee00734d). In this work we re-investigate the sodium-doped strontium silicate material that was reported to exhibit the highest oxide ion conductivity in the solid solution, nominally Sr0.55Na0.45SiO2.775. The results show lower levels of total conductivity than previously reported and sub-micron elemental mapping demonstrates, in a similar manner to that reported for the Sr0.8K0.2Si0.5Ge0.5O2.9 composition, an inhomogeneous chemical distribution correlating with a multiphase material. It is also shown that the conductivity is not related to protonic mobility. A density functional theory computational approach provides a theoretical justification for these new results, related to the high energetic costs associated with oxygen vacancy formation. This journal is

Understanding the defect chemistry of alkali metal strontium silicate solid solutions: insights from experiment and theory

KAUST Repository

Bayliss, Ryan D.

2014-09-24

© the Partner Organisations 2014. Recent reports of remarkably high oxide ion conduction in a new family of strontium silicates have been challenged. It has recently been demonstrated that, in the nominally potassium substituted strontium germanium silicate material, the dominant charge carrier was not the oxygen ion, and furthermore that the material was not single phase (R. D. Bayliss et. al., Energy Environ. Sci., 2014, DOI: 10.1039/c4ee00734d). In this work we re-investigate the sodium-doped strontium silicate material that was reported to exhibit the highest oxide ion conductivity in the solid solution, nominally Sr0.55Na0.45SiO2.775. The results show lower levels of total conductivity than previously reported and sub-micron elemental mapping demonstrates, in a similar manner to that reported for the Sr0.8K0.2Si0.5Ge0.5O2.9 composition, an inhomogeneous chemical distribution correlating with a multiphase material. It is also shown that the conductivity is not related to protonic mobility. A density functional theory computational approach provides a theoretical justification for these new results, related to the high energetic costs associated with oxygen vacancy formation. This journal is

Chemistry and evolution of Titan's atmosphere

International Nuclear Information System (INIS)

Strobel, D.F.

1982-01-01

The chemistry and evolution of Titan's atmosphere is reviewed in the light of the scientific findings from the Voyager mission. It is argued that the present N 2 atmosphere may be Titan's initial atmosphere rather than photochemically derived from an original NH 3 atmosphere. The escape rate of hydrogen from Titan is controlled by photochemical production from hydrocarbons. CH 4 is irreversibly converted to less hydrogen rich hydrocarbons, which over geologic time accumulate on the surface to a layer thickness of approximately 0.5 km. Magnetospheric electrons interacting with Titan's exosphere may dissociate enough N 2 into hot, escaping N atoms to remove approximately 0.2 of Titan's present atmosphere over geologic time. The energy dissipation of magnetospheric electrons exceeds solar e.u.v. energy deposition in Titan's atmosphere by an order of magnitude and is the principal driver of nitrogen photochemistry. The environmental conditions in Titan's upper atmosphere are favorable to building up complex molecules, particularly in the north polar cap region. (author)

The effect of CHA-doped Sr addition to the mechanical strength of metakaolin dental implant geopolymer composite

Science.gov (United States)

Sunendar, Bambang; Fathina, Afiya; Harmaji, Andrie; Mardhian, Deby Fajar; Asri, Lia; Widodo, Haris Budi

2017-09-01

The prospective material for implant plate required sufficient mechanical properties to maintain fracture fixation and resist physiological stress until bone healing process finished. Various problem implant plate based on metal and polymer materials when used as fixation for bone defect case induced developmental of bioceramic for implant plate materials. Materials that now has been attract a lot of attention is carbonate apatite and strontium as doping which known to have good biocompability along with biointegrity and mechanical charateristics. Other materials that have been known to have good mechanical properties are metakaolin and use of chitosan as coupling agent. Metakaolin and carbonate apatite can be produced by sol-gel methode which simpler, economical and energy-saving procedure furthermore use of chitosan which is widely found in the nature of Indonesia can be used to encourage the utilization of natural resources. The aim fo this paper is to investigated effect of CHA-doped Sr 5 (%) mol addition to the mechanical strength of metakaolin dental implant geoploymer composite. In this paper metakaolin is used as geopolymerization precursors. The test results have shown that addition of filler of apatite carbonate doped 5% mol strontium can be said to increase the value of mechnical properties but high concentration of calcium in the nanocomposite also can complicate the equilibrium of the geopolymerization process and induce alkali aggregate reactivity (AAR). The sample group of nanocomposite of metakaolin and carbonate apatite-doped 5% mol strontium (2: 1% wt) with 2% chitosan as a coupling agent based on geopolymerization for implant plate application has the best mechanical properties among all sample groups but does not qualify as an implant plate on cortical bone but can be used for the application of the implant plate on the trabecular bone specifically and potentially as a bone initiator.

Titan Polar Landscape Evolution

Science.gov (United States)

Moore, Jeffrey M.

2016-01-01

With the ongoing Cassini-era observations and studies of Titan it is clear that the intensity and distribution of surface processes (particularly fluvial erosion by methane and Aeolian transport) has changed through time. Currently however, alternate hypotheses substantially differ among specific scenarios with respect to the effects of atmospheric evolution, seasonal changes, and endogenic processes. We have studied the evolution of Titan's polar region through a combination of analysis of imaging, elevation data, and geomorphic mapping, spatially explicit simulations of landform evolution, and quantitative comparison of the simulated landscapes with corresponding Titan morphology. We have quantitatively evaluated alternate scenarios for the landform evolution of Titan's polar terrain. The investigations have been guided by recent geomorphic mapping and topographic characterization of the polar regions that are used to frame hypotheses of process interactions, which have been evaluated using simulation modeling. Topographic information about Titan's polar region is be based on SAR-Topography and altimetry archived on PDS, SAR-based stereo radar-grammetry, radar-sounding lake depth measurements, and superposition relationships between geomorphologic map units, which we will use to create a generalized topographic map.

Influence of reactor irradiation on the protons intercalation and stability of barium cerates and strontium cerates

International Nuclear Information System (INIS)

Aksenova, T.I.; Khromushin, I.V.; Zhotabaev, Zh.R.; Kornienko, P.A.; Munasbaeva, K.K.

2005-01-01

The work is devoted to study of reactor irradiation influence on the gas-solid exchange processes in the high-temperature proton semiconductors on the base of cerates and strontium. A number of new regularities of influence of content of some proton semiconductors on the gas-solid exchange processes was established. It is shown, that increase of rate of cation doping rate leads to considerable lowering in its of carbonic gas content, and therefore to improvement their tribological properties. It is revealed, that irradiation of polycrystalline samples leads to growth of oxygen amount desorbed from samples, whereas irradiation of monocrystalline samples practically does not has effect on the desorbed oxygen amount. It was found, that character of relation of intercalated in the sample protons depend on sample doping rate

White- and blue-light-emitting dysprosium(III) and terbium(III)-doped gadolinium titanate phosphors.

Science.gov (United States)

Antić, Ž; Kuzman, S; Đorđević, V; Dramićanin, M D; Thundat, T

2017-06-01

Here we report the synthesis and structural, morphological, and photoluminescence analysis of white- and blue-light-emitting Dy 3 + - and Tm 3 + -doped Gd 2 Ti 2 O 7 nanophosphors. Single-phase cubic Gd 2 Ti 2 O 7 nanopowders consist of compact, dense aggregates of nanoparticles with an average size of ~25 nm for Dy 3 + -doped and ~50 nm for Tm 3 + -doped samples. The photoluminescence results indicated that ultraviolet (UV) light excitation of the Dy 3 + -doped sample resulted in direct generation of white light, while a dominant yellow emission was obtained under blue-light excitation. Intense blue light was obtained for Tm 3 + -doped Gd 2 Ti 2 O 7 under UV excitation suggesting that this material could be used as a blue phosphor. Copyright © 2016 John Wiley & Sons, Ltd.

STRUCTURAL CHARACTERISTICS & DIELECTRIC PROPERTIES OF TANTALUM OXIDE DOPED BARIUM TITANATE BASED MATERIALS

Directory of Open Access Journals (Sweden)

Md. Fakhrul Islam

2013-01-01

Full Text Available In this research, the causal relationship between the dielectric properties and the structural characteristics of 0.5 & 1.0 mole % Ta2O5 doped BaTiO3 based ceramic materials were investigated under different sintering conditions. Dielectric properties and microstructure of BaTio3 ceramics were significantly influenced by the addition of a small amount of Ta2O5. Dielectric properties were investigated by measuring the dielectric constant (k as a function of temperature and frequency. Percent theoretical density (%TD above 90 % was achieved for 0.5 and 1.0 mole %Ta2O5 doped BaTiO3. It was observed that the grain size decreased markedly above a doping concentration of 0.5 mole % Ta2O5. Although fine grain size down to 200 - 300 nm was attained, grain sizes in the range of 1-1.8µm showed the most alluring properties. The fine-grain quality and high density of the Ta2O5 doped BaTiO3 ceramic resulted in tenfold increase of dielectric constant. Stable value of dielectric constant as high as 13000 - 14000 was found in the temperature range of 55 to 80 °C, for 1.0 mole % Ta2O5 doped samples with corresponding shift of Curie point to ~82 °C. Experiments divulged that incorporation of a proper content of Ta2O5 in BaTiO3 could control the grain growth, shift the Curie temperature and hence significantly improve the dielectric property of the BaTiO3 ceramics.

Interaction of Titan's atmosphere with Saturn's magnetosphere

International Nuclear Information System (INIS)

Hartle, R.E.

1985-01-01

The Voyager 1 measurements made during the Titan flyby reveal that Saturn's rotating magnetospheric plasma interacts directly with Titan's neutral atmosphere and ionosphere. This results from the lack of an intrinsic magnetic field at Titan. The interaction induces a magnetosphere which deflects the flowing plasma around Titan and forms a plasma wake downstream. Within the tail of the induced magnetosphere, ions of ionospheric origin flow away from Titan. Just outside Titan's magnetosphere, a substantial ion-exosphere forms from an extensive hydrogen-nitrogen exosphere. The exospheric ions are picked up and carried downstream into the wake by the plasma flowing around Titan. Mass loading produced by the addition of exospheric ions slows the wake plasma down considerably in the vicinity of the magnetopause. 36 references

Strontium isotopic study of sediment from the Ross Sea

International Nuclear Information System (INIS)

Kovach, J.; Faure, G.

1977-01-01

A preliminary report summarizing the results of a study of the strontium-87/strontium-86 ratios and of the rubidium and strontium concentrations of the fine-grained (less than 150 microns) noncarbonate fractions of sediment samples from core E32-25 raised from a depth of 327 fathoms in the Ross Sea at 78 0 31.0'S 164 0 24.7'W was presented. The strontium-87/strontium-86 ratios of the samples analyzed range from 0.7119 to 0.7220. Rubidium and strontium concentrations range, respectively, from 126 to 164 parts per million and from 113 to 174 parts per million. The observed strontium-87/strontium-86 ratios and strontium concentrations in sediment samples from core E32-25 fit a hyperbolic curve. These ratios can be used to estimate the concentrations of volcanogenic detritus in the sediment samples. The results of this study provide additional baseline data for anticipated future studies of sediment cores to be recovered from beneath the Ross Ice Shelf by the Ross Ice Shelf Project. 1 figure

Effect of yttrium chromite doping on its resistance to high-temperature salt and gas corrosions

International Nuclear Information System (INIS)

Oryshich, I.V.; Poryadchenko, N.E.; Rakitskij, A.N.; Bega, N.D.

1996-01-01

Effect of yttrium chromite doping with 2-4 group metal oxides on the corrosion resistance in the air at 1300 C during 5 hours and in sodium chloride and sulfate melts at 900 C during 20 hours is investigated. A notable increase of corrosion resistance is achieved under complex doping with zirconium and magnesium oxides in a quantity, close to solubility in yttrium oxide and solubility by aluminium oxide. Doping with calcium and strontium oxides in the quantities, dose to solubility in yttrium oxide does not produce any notable effect, and at higher concentrations it reduces the corrosion resistance in media indicated. Refs. 8, refs. 2, tabs. 1

Effects of calcium and magnesium on strontium distribution coefficients

Science.gov (United States)

Bunde, R.L.; Rosentreter, J.J.; Liszewski, M.J.; Hemming, C.H.; Welhan, J.

1997-01-01

The effects of calcium and magnesium on the distribution of strontium between a surficial sediment and simulated wastewater solutions were measured as part of an investigation to determine strontium transport properties of surficial sediment at the Idaho National Engineering Laboratory (INEL), Idaho. The investigation was conducted by the U.S. Geological Survey and Idaho State University, in cooperation with the U.S. Department of Energy. Batch experimental techniques were used to determine strontium linear sorption isotherms and distribution coefficients (K(d)'s) using simulated wastewater solutions prepared at pH 8.0??0.1 with variable concentrations of calcium and magnesium. Strontium linear sorption isotherm K(d)'s ranged from 12??1 to 85??3 ml/g, increasing as the concentration of calcium and magnesium decreased. The concentration of sorbed strontium and the percentage of strontium retained by the sediment were correlated to aqueous concentrations of strontium, calcium, and magnesium. The effect of these cation concentrations on strontium sorption was quantified using multivariate least-squares regression techniques. Analysis of data from these experiments indicates that increased concentrations of calcium and magnesium in wastewater discharged to waste disposal ponds at the INEL increases the availability of strontium for transport beneath the ponds by decreasing strontium sorption to the surficial sediment.

Hanford waste encapsulation: strontium and cesium

International Nuclear Information System (INIS)

Jackson, R.R.

1976-06-01

The strontium and cesium fractions separated from high radiation level wastes at Hanford are converted to the solid strontium fluoride and cesium chloride salts, doubly encapsulated, and stored underwater in the Waste Encapsulation and Storage Facility (WESF). A capsule contains approximately 70,000 Ci of 137 Cs or 70,000 to 140,000 Ci of 90 Sr. Materials for fabrication of process equipment and capsules must withstand a combination of corrosive chemicals, high radiation dosages and frequently, elevated temperatures. The two metals selected for capsules, Hastelloy C-276 for strontium fluoride and 316-L stainless steel for cesium chloride, are adequate for prolonged containment. Additional materials studies are being done both for licensing strontium fluoride as source material and for second generation process equipment

Titanic: A Statistical Exploration.

Science.gov (United States)

Takis, Sandra L.

1999-01-01

Uses the available data about the Titanic's passengers to interest students in exploring categorical data and the chi-square distribution. Describes activities incorporated into a statistics class and gives additional resources for collecting information about the Titanic. (ASK)

Electrical conductivity improvement of strontium titanate doped lead vanadate glasses by nanocrystallization

Energy Technology Data Exchange (ETDEWEB)

El-Desoky, M.M., E-mail: mmdesoky@gmail.co [Physics Department, Faculty of Education, Suez Canal University, El-Arish (Egypt); Zayed, H.S.S.; Ibrahim, F.A.; Ragab, H.S. [Physics Department, Faculty of Education, Suez Canal University, El-Arish (Egypt)

2009-11-15

The structural and electrical conductivity (sigma) of annealed SrTiO{sub 3}-PbO{sub 2}-V{sub 2}O{sub 5} glasses were studied. The annealing of initially glass samples leads to formation of nanocrystalline grains embedded in the glassy matrix. XRD patterns of the glass-ceramic samples show that nanocrystals were embedded in the glassy matrix with an average grain size of 32 nm. The glass-ceramic nanocrystals obtained by annealing at temperatures close to the crystallization temperature T{sub c} exhibit enhancement of electrical conductivity up to four orders of magnitude than initially glasses. The enhancement of the electrical conductivity due to annealing was attributed to two interdependent factors: (i) an increase of concentration of V{sup 4+}-V{sup 5+} pairs; and (ii) formation of defective, well-conducting regions along the glass-crystallites interfaces. From the conductivity temperature relation, it was found that small polaron hopping model was applicable at temperature above theta{sub D}/2 (theta{sub D}, the Debye temperature). The electrical conduction at T >theta{sub D}/2 was due to non-adiabatic small polaron hopping (SPH) of electrons between vanadium ions. The parameters obtained from the fits of the experimental data to this model appear reasonable and are consistent with glass composition.

Electrical conductivity improvement of strontium titanate doped lead vanadate glasses by nanocrystallization

International Nuclear Information System (INIS)

El-Desoky, M.M.; Zayed, H.S.S.; Ibrahim, F.A.; Ragab, H.S.

2009-01-01

The structural and electrical conductivity (σ) of annealed SrTiO 3 -PbO 2 -V 2 O 5 glasses were studied. The annealing of initially glass samples leads to formation of nanocrystalline grains embedded in the glassy matrix. XRD patterns of the glass-ceramic samples show that nanocrystals were embedded in the glassy matrix with an average grain size of 32 nm. The glass-ceramic nanocrystals obtained by annealing at temperatures close to the crystallization temperature T c exhibit enhancement of electrical conductivity up to four orders of magnitude than initially glasses. The enhancement of the electrical conductivity due to annealing was attributed to two interdependent factors: (i) an increase of concentration of V 4+ -V 5+ pairs; and (ii) formation of defective, well-conducting regions along the glass-crystallites interfaces. From the conductivity temperature relation, it was found that small polaron hopping model was applicable at temperature above θ D /2 (θ D , the Debye temperature). The electrical conduction at T >θ D /2 was due to non-adiabatic small polaron hopping (SPH) of electrons between vanadium ions. The parameters obtained from the fits of the experimental data to this model appear reasonable and are consistent with glass composition.

The age of Titan's surface

Science.gov (United States)

Neish, C. D.; Lorenz, R. D.

2010-04-01

High-resolution images of the surface of Titan taken by the Cassini spacecraft reveal a world with an extreme paucity of impact craters. Planetary surfaces are commonly dated by dividing the number of impact craters by the estimated impactor flux, but this approach has been confounded at Titan by several difficulties. First, high-resolution imaging of the surface of Titan is far from complete (in the near-infrared as well as radar). As of December 2007, Cassini RADAR images covered only 22% of its surface. However, we can use Monte-Carlo models to explore how many craters of a given size (with large or very large craters being of particular interest) may be present in the unobserved areas. Second, literature descriptions of the crater formation rate (e.g. Korycansky and Zahnle 2005 and Artemieva and Lunine 2005) are apparently not in agreement. We discuss possible resolutions. Third, since surface modification processes are ongoing, the actual number of craters on Titan's surface remains uncertain, as craters may be eroded beyond recognition, or obscured by lakes or sand seas. In this connection, we use the Earth as an analogue. The Earth is in many ways the most "Titan-like" world in the solar system, with extensive modification by erosion, burial, tectonism, and volcanism. We compare the observed number of terrestrial craters to the expected terrestrial impactor flux to determine the crater reduction factor for a world similar to Titan. From this information, we can back out the actual number of craters on Titan's surface and estimate its crater retention age. An accurate age estimate will be critical for constraining models of Titan's formation and evolution.

Structural Characteristics & Dielectric Properties of Tantalum Oxide Doped Barium Titanate Based Materials

Directory of Open Access Journals (Sweden)

Rubayyat Mahbub

2012-11-01

Full Text Available In this research, the causal relationship between the dielectric properties and the structural characteristics of 0.5 & 1.0 mol% Ta2O5 doped BaTiO3 based ceramic materials were investigated under different sintering conditions. Dielectric properties and microstructure of BaTio3 ceramics were significantly influenced by the addition of a small amount of Ta2O5. Dielectric properties were investigated by measuring the dielectric constant (k as a function of temperature and frequency. Percent theoretical density (%TD above 90% was achieved for 0.5 and 1.0 mol% Ta2O5 doped BaTiO3. It was observed that the grain size decreased markedly above a doping concentration of 0·5 mol% Ta2O5. Although fine grain size down to 200-300nm was attained, grain sizes in the range of 1-1.8µm showed the most alluring properties. The fine-grain quality and high density of the Ta2O5 doped BaTiO3 ceramic resulted in tenfold increase of dielectric constant. Stable value of dielectric constant as high as 13000-14000 was found in the temperature range of  55 to 80°C, for 1.0 mol% Ta2O5 doped samples with corresponding shift of Curie point to ~82°C. Experiments divulged that incorporation of a proper content of Ta2O5 in BaTiO3 could control the grain growth, shift the Curie temperature and hence significantly improve the dielectric property of the BaTiO3 ceramics.

The Titan Sky Simulator ™ - Testing Prototype Balloons in Conditions Approximating those in Titan's Atmosphere

Science.gov (United States)

Nott, Julian

This paper will describe practical work flying prototype balloons in the "The Titan Sky Simulator TM " in conditions approximating those found in Titan's atmosphere. Saturn's moon, Titan, is attracting intense scientific interest. This has led to wide interest in exploring it with Aerobots, balloons or airships. Their function would be similar to the Rovers exploring Mars, but instead of moving laboriously across the rough terrain on wheels, they would float freely from location to location. To design any balloon or airship it is essential to know the temperature of the lifting gas as this influences the volume of the gas, which in turn influences the lift. To determine this temperature it is necessary to know how heat is transferred between the craft and its surroundings. Heat transfer for existing balloons is well understood. However, Titan conditions are utterly different from those in which balloons have ever been flown, so heat transfer rates cannot currently be calculated. In particular, thermal radiation accounts for most heat transfer for existing balloons but over Titan heat transfer will be dominated by convection. To be able to make these fundamental calculations, it is necessary to get fundamental experimental data. This is being obtained by flying balloons in a Simulator filled with nitrogen gas at very low temperature, about 95° K / minus 180° C, typical of Titan's temperatures. Because the gas in the Simulator is so cold, operating at atmospheric pressure the density is close to that of Titan's atmosphere. "The Titan Sky Simulator TM " has an open interior approximately 4.5 meter tall and 2.5 meters square. It has already been operated at 95° K/-180° C. By the time of the Conference it is fully expected to have data to present from actual balloons flying at this temperature. Perhaps the most important purpose of this testing is to validate numerical [computational fluid dynamics] models being developed by Tim Colonius of Caltech. These numerical

Determination of charge carrier mobility in doped low density polyethylene using DC transients

DEFF Research Database (Denmark)

Khalil, M.Salah; Henk, Peter O; Henriksen, Mogens

1989-01-01

Charge carrier mobility was determined for plain and doped low-density polyethylene (LDPE) using DC transient currents. Barium titanate was used as a strongly polar dopant and titanium dioxide as a semiconductor dopant. The values of the mobility obtained were on the order of 10-10 cm2 v-1 s-1...

Distribution of strontium in milk component

International Nuclear Information System (INIS)

Rosskopfova, O.; Galambos, M.; Rajec, P.

2011-01-01

The distribution of strontium between the milk components, i.e., serum, casein micelles, whey and hydroxyapatite was determined. The sorption on hydroxyapatite was investigated using batch method and radiotracer technique. The aqueous phase comprised of either milk or whey. The sorption of strontium on hydroxyapatite depended on the method of its preparation and on the composition of the aqueous phase. The sorption of strontium was increased with an increase of pH. The presence of citrate species resulted in decrease of the sorption of strontium on hydroxyapatite. The sorption of 85 Sr on hydroxyapatite decreased with the increasing concentration of Ca 2+ ions. Addition of Ca 2+ ions to milk resulted in milk pH decrease. The decrease in pH value after calcium addition to milk is related to exchanges between added calcium and micellar H + . The average value of strontium sorption on casein micelles in milk with presence of hydroxyapatite was (47.3 ± 5.6) %. The average value of sorption of 85 Sr on casein micelles in milk without the addition of hydroxyapatite was (68.9 ± 2.2) %. (author)

The atmospheric temperature structure of Titan

Science.gov (United States)

Mckay, Christopher P.; Pollack, J. B.; Courtin, Regis; Lunine, Jonathan I.

1992-01-01

The contribution of various factors to the thermal structure of Titan's past and present atmosphere are discussed. A one dimensional model of Titan's thermal structure is summarized. The greenhouse effect of Titan's atmosphere, caused primarily by pressure induced opacity of N2, CH4, and H2, is discussed together with the antigreenhouse effect dominated by the haze which absorbs incident sunlight. The implications for the atmosphere of the presence of an ocean on Titan are also discussed.

Structural and electrical properties of Barium Titanate (BaTiO3 and Neodymium doped BaTiO3 (Ba0.995Nd0.005TiO3

Directory of Open Access Journals (Sweden)

Tuan Sulong Tuan Amirah

2017-01-01

Full Text Available Barium titanate (BaTiO3 and Neodymium (Nd doped BaTiO3 with composition Ba0.995Nd0.005TiO3 were prepared using conventional solid state reaction method to study the dielectric properties of materials. Pure phase samples were found at final heating temperature of 1400°C for overnight. X-ray diffraction analysis reveals the changes in the lattice parameter and unit cell volume of the pure perovskite tetragonal structure with space group (P4mm. Electrical analysis is carried out to investigate the dielectric properties, conductivity behaviour and dielectric loss of BaTiO3 and Ba0.995Nd0.005TiO3. Ba0.995Nd0.005TiO3 have a broaden dielectric peaks with high permittivity of 8000 and reasonably low loss tan δ which is about 0.004 (1 kHz.

Structural contribution to the ferroelectric fatigue in lead zirconate titanate ceramics

Science.gov (United States)

Hinterstein, M.; Rouquette, J.; Haines, J.; Papet, Ph.; Glaum, J.; Knapp, M.; Eckert, J.; Hoffman, M.

2014-09-01

Many ferroelectric devices are based on doped lead zirconate titanate (PZT) ceramics with compositions near the morphotropic phase boundary (MPB), at which the relevant material's properties approach their maximum. Based on a synchrotron x-ray diffraction study of MPB PZT, bulk fatigue is unambiguously found to arise from a less effective field induced tetragonal-to-monoclinic transformation, at which the degradation of the polarization flipping is detected by a less intense and more diffuse anomaly in the atomic displacement parameter of lead. The time dependence of the ferroelectric response on a structural level down to 250 μs confirms this interpretation in the time scale of the piezolectric strain response.

Ferroelectric relaxor behaviour and impedance spectroscopy of Bi{sub 2}O{sub 3}-doped barium zirconium titanate ceramics

Energy Technology Data Exchange (ETDEWEB)

Mahajan, Sandeep; Thakur, O P; Bhattacharya, D K [Electroceramics Group, Solid State Physics Laboratory, Lucknow Road, Delhi-110054 (India); Sreenivas, K, E-mail: omprakasht@hotmail.co [Department of Physics and Astrophysics, University of Delhi- 110007 (India)

2009-03-21

Bi{sub 2}O{sub 3}-doped barium zirconate titanate ceramics, Ba{sub 1-x}Bi{sub x}(Zr{sub 0.05}Ti{sub 0.95})O{sub 3}, have been prepared by the conventional solid-state reaction method. The ferroelectric relaxor behaviour and dielectric properties have been investigated in detail. By XRD analysis, it is suggested that up to x = 0.04, Bi{sup 3+} substitutes A-site ion, and thereafter with higher Bi{sup 3+} content, it enters the B-site sub lattice. Substitution of Bi{sup 3+} ions induces ferroelectric relaxor behaviour and the degree of relaxation behaviour increases with bismuth concentration. The remanent polarization and strain behaviour show a slight increase with the substitution level. The degree of hysteresis (strain versus electric field) also reduces from 21.4% to 4.6% with bismuth substitution. Impedance measurements were made on the prepared sample over a wide range of temperatures (300-723 K) and frequencies (40 Hz-1 MHz), which show the presence of both bulk and grain boundary effects in the material. The bulk and grain boundary conductivities determined from impedance study indicate the Arrhenius-type thermally activated process. Impedance spectroscopy is shown to be an efficient method capable of detecting the contributions of the resistances of grains and grain boundaries to the complex impedance of a ceramic system, accurately estimating its electrical conductivity as well as its corresponding activation energies and drawing conclusions on its structural properties.

Strontium metabolism and mechanism of interaction with mineralized tissues

International Nuclear Information System (INIS)

Wadkins, C.L.; Fu Peng, C

1981-01-01

This paper examines the administration of strontium to birds and mammals which results in limited incorporation into skeletal tissue, depressed intestinal calcium absorption, and development of rachitic bone lesions. Comparison of radiostrontium and radiocalcium incorporation by intact animals reveals discrimination against strontium in favor of calcium. Comparison of the Sr 85 - Ca 2+ and Ca 45 - Ca 2+ exchange reveals discrimination against strontium in favor of calcium. Thus, this system manifests product specificity, strontium inhibition, strontium exchange, and discrimination observed with intact animals

Uptake behavior of titanium molybdophosphate for cesium and strontium

International Nuclear Information System (INIS)

Yavari, R.; Ahmadi, S.J.; Huang, Y.D.

2010-01-01

This study investigates uptake of cesium and strontium from aqueous solution similar to nuclear waste on three samples of titanium molybdophosphate (TMP) synthesized under various conditions. Effects of concentration of sodium nitrate, pH and contact time on the uptake of cesium and strontium have been studied by bath method. The results showed that TMP has high affinity toward cesium and strontium at pH > 2 and relatively low concentration of sodium nitrate. Kinetic data indicated that cesium uptake process to achieve equilibrium was faster than strontium. Cesium and strontium breakthrough curves were examined at 25 deg C using column packed with H 3 O + form of TMP and breakthrough curves showed symmetrical S-shaped profiles. At the same time, the calculated breakthrough capacity for cesium was higher than strontium. The results of desorption studies showed that over 99% of cesium and strontium was washed out of column by using 4 M NH 4 Cl solution. This study suggests that TMP can have great potential applications for the removal of strontium and specially cesium from nuclear waste solution. (author)

Calcium phosphate cements with strontium halides as radiopacifiers.

Science.gov (United States)

López, Alejandro; Montazerolghaem, Maryam; Engqvist, Håkan; Ott, Marjam Karlsson; Persson, Cecilia

2014-02-01

High radiopacity is required to monitor the delivery and positioning of injectable implants. Inorganic nonsoluble radiopacifiers are typically used in nondegradable bone cements; however, their usefulness in resorbable cements is limited due to their low solubility. Strontium halides, except strontium fluoride, are ionic water-soluble compounds that possess potential as radiopacifiers. In this study, we compare the radiopacity, mechanical properties, composition, and cytotoxicity of radiopaque brushite cements prepared with strontium fluoride (SrF2 ), strontium chloride (SrCl2 ·6H2 O), strontium bromide (SrBr2 ), or strontium iodide (SrI2 ). Brushite cements containing 10 wt % SrCl2 ·6H2 O, SrBr2 , or SrI2 exhibited equal to or higher radiopacity than commercial radiopaque cements. Furthermore, the brushite crystal lattice in cements that contained the ionic radiopacifiers was larger than in unmodified cements and in cements that contained SrF2 , indicating strontium substitution. Despite the fact that the strontium halides increased the solubility of the cements and affected their mechanical properties, calcium phosphate cements containing SrCl2 ·6H2 O, SrBr2 , and SrI2 showed no significant differences in Saos-2 cell viability and proliferation with respect to the control. Strontium halides: SrCl2 ·6H2 O, SrBr2 , and SrI2 may be potential candidates as radiopacifiers in resorbable biomaterials although their in vivo biocompatibility, when incorporated into injectable implants, is yet to be assessed. Copyright © 2013 Wiley Periodicals, Inc.

Influence of defect mobility on electrostrain in acceptor-doped Ba0.80Sr0.20TiO3

Directory of Open Access Journals (Sweden)

K. Vani

2012-12-01

Full Text Available This study reports significant differences in the defect-mediated electrostrain in B-site trivalent ions (Fe3+ and Mn3+ doped Barium titanate based system. Electron Paramagnetic Resonance (EPR Spectroscopy has been employed as a structural probe for understanding the symmetry of defects. Differences in the reorientation of the defect dipoles have been correlated with the electrostrain. Mechanism for the higher strain in Mn-doped system has also been explained.

Titan Orbiter Aerorover Mission

Science.gov (United States)

Sittler Jr., E. C.; Acuna, M.; Burchell, M. J.; Coates, A.; Farrell, W.; Flasar, M.; Goldstein, B. E.; Gorevan, S.; Hartle, R. E.; Johnson, W. T. K.

2001-01-01

We propose a combined Titan orbiter and Titan Aerorover mission with an emphasis on both in situ and remote sensing measurements of Titan's surface, atmosphere, ionosphere, and magnetospheric interaction. The biological aspect of the Titan environment will be emphasized by the mission (i.e., search for organic materials which may include simple organics to 'amono' analogues of amino acids and possibly more complex, lightening detection and infrared, ultraviolet, and charged particle interactions with Titan's surface and atmosphere). An international mission is assumed to control costs. NASA will provide the orbiter, launch vehicle, DSN coverage and operations, while international partners will provide the Aerorover and up to 30% of the cost for the scientific instruments through collaborative efforts. To further reduce costs we propose a single PI for orbiter science instruments and a single PI for Aerorover science instruments. This approach will provide single command/data and power interface between spacecraft and orbiter instruments that will have redundant central DPU and power converter for their instruments. A similar approach could be used for the Aerorover. The mission profile will be constructed to minimize conflicts between Aerorover science, orbiter radar science, orbiter radio science, orbiter imaging science, and orbiter fields and particles (FP) science. Additional information is contained in the original extended abstract.

Strontium sorption on Savannah River Plant soils

International Nuclear Information System (INIS)

Hoeffner, S.L.

1984-12-01

A laboratory study of strontium-85 sorption was conducted using Savannah River Plant soil and groundwater from the low-level waste burial ground. Systematic variation of soil and water composition indicates that strontium sorption is most strongly a function of pH. Changes in clay content and in K + , Ca 2+ , or Mg 2+ concentrations influence strontium sorption indirectly through the slight pH changes which result. The ions Na + , Cl - , and NO 3 - have no effect. Ferrous ion, added to groundwater to simulate the conditions of water at the bottom of waste trenches, did not account for low strontium sorption observed with some trench waters

Phase stabilisation of hexagonal barium titanate doped with transition metals: A computational study

International Nuclear Information System (INIS)

Dawson, J.A.; Freeman, C.L.; Harding, J.H.; Sinclair, D.C.

2013-01-01

Interatomic potentials recently developed for the modelling of BaTiO 3 have been used to explore the stabilisation of the hexagonal polymorph of BaTiO 3 by doping with transition metals (namely Mn, Co, Fe and Ni) at the Ti-site. Classical simulations have been completed on both the cubic and hexagonal polymorphs to investigate the energetic consequences of transition metal doping on each polymorph. Ti-site charge compensation mechanisms have been used for the multi-valent transition metal ions and cluster binding energies have been considered. Simulations show a significant energetic gain when doping occurs at Ti sites in the face sharing dimers (Ti 2 sites) of the hexagonal polymorph compared with the doping of the cubic polymorph. This energetic difference between the two polymorphs is true for all transition metals tested and all charge states and in the case of tri- and tetra-valent dopants negative solution energies are found for the hexagonal polymorph suggesting actual polymorph stabilisation occurs with the incorporation of these ions as observed experimentally. Oxidation during incorporation of Ni 2+ and Fe 3+ ions has also been considered. - Graphical abstract: The representation of the strongest binding energy clusters for tri-valent dopants—(a) Ti 2 /O 1 cluster and (b) Ti 2 /O 2 cluster. Highlights: ► Classical simulations show a significant energetic gain when doping occurs at Ti sites in the face sharing dimers (Ti2 sites) of the hexagonal polymorph compared with the doping of the cubic polymorph. ► This energetic difference between the two polymorphs is true for all transition metals tested and all charge states. ► In the case of tri- and tetra- valent dopants negative solution energies are found for the hexagonal polymorph suggesting actual polymorph stabilisation occurs with the incorporation of these ions

Fixation of Radioactive Strontium in Soil

DEFF Research Database (Denmark)

Gregers-Hansen, Birte

1964-01-01

of the other long-lived fission products. Much work2–5 has, therefore, been concerned with the possibility of bringing down the strontium-90 uptake by plants through ploughing or through the addition of lime or fertilizer to the soil. Another factor, the effect of ageing on the availability of strontium, has...... been considered6,7. In general, these methods appear to be of little practical value, except for deep ploughing and the liming of acid soils, both of which will reduce the strontium uptake by a factor of 3–4....

Sorption isolation of strontium from seawater

International Nuclear Information System (INIS)

Avramenko, V.A.; Zheleznov, V.V.; Kaplun, E.V.; Sokol'nitskaya, T.A.; Yukhkam, A.A.

2001-01-01

Sorption isolation of strontium from seawater is considered and prospects of use of selective adsorbents for purification of seawater or liquid radioactive wastes mixed with seawater from 90 Sr are discussed. Comparative analysis of sorptive properties of adsorbents of different nature is done. It is shown that sorption-reagent materials developed by authors can to afford effective separation of 90 Sr from seawater. Possible mechanism of strontium sorption by these adsorbents is considered. The prospect of their use for purification of liquid radioactive wastes from strontium is shown [ru

Titan AVIATR - Aerial Vehicle for In Situ and Airborne Titan Reconnaissance

Science.gov (United States)

Kattenhorn, Simon A.; Barnes, J. W.; McKay, C. P.; Lemke, L.; Beyer, R. A.; Radebaugh, J.; Adamkovics, M.; Atkinson, D. H.; Burr, D. M.; Colaprete, T.; Foch, R.; Le Mouélic, S.; Merrison, J.; Mitchell, J.; Rodriguez, S.; Schaller, E.

2010-10-01

Titan AVIATR - Aerial Vehicle for In Situ and Airborne Titan Reconnaissance - is a small (120 kg), nuclear-powered Titan airplane in the Discovery/New Frontiers class based on the concept of Lemke (2008 IPPW). The scientific goals of the mission are designed around the unique flexibility offered by an airborne platform: to explore Titan's diversity of surface landforms, processes, and compositions, as well as to study and measure the atmospheric circulation, aerosols, and humidity. AVIATR would address and surpass many of the science goals of hot-air balloons in Titan flagship studies. The strawman instrument payload is narrowly focused on the stated scientific objectives. The optical remote sensing suite comprises three instruments - an off-nadir high-resolution 2-micron camera, a horizon-looking 5-micron imager, and a 1-6 micron pushbroom near-infrared spectrometer. The in situ instruments include atmospheric structure, a methane humidity sensor, and a raindrop detector. An airplane has operational advantages over a balloon. Its piloted nature allows a go-to capability to image locations of interest in real time, thereby allowing for directed exploration of many features of primary geologic interest: Titan's sand dunes, mountains, craters, channels, and lakes. Subsequent imaging can capture changes in these features during the primary mission. AVIATR can fly predesigned routes, building up large context mosaics of areas of interest before swooping down to low altitude to acquire high-resolution images at 30-cm spatial sampling, similar to that of HiRISE at Mars. The elevation flexibility of the airplane allows us to acquire atmospheric profiles as a function of altitude at any desired location. Although limited by the direct-to-Earth downlink bandwidth, the total scientific data return from AVIATR will be >40 times that returned from Huygens. To maximize the science per bit, novel data storage and downlink techniques will be employed, including lossy compression

Determination of mineral radioactive strontium-{sup 90} in urines; Recherche du strontium mineral radioactif {sup 90}Sr dans les urines

Energy Technology Data Exchange (ETDEWEB)

Jeanmaire, L; Jammet, H; Bertrand, S [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

An analytical procedure for radioactive strontium in urine is described. As a first step, a precipitation of calcium oxalate performed on the urine, allows to detect the presence of various fission products and particularly of strontium which is carried by the precipitate. Strontium can then be selectively separated on ion exchange resins. By studying the growth curve of {beta} activity, it is possible to determine the activities which may be attributed to {sup 89}Sr and {sup 90}Sr respectively. (author) [French] Cet article decrit une technique de dosage du strontium radioactif dans les urines. Dans un premier stade, une precipitation d'oxalate de calcium effectuee sur l'urine permet de deceler la presence de differents produits de fission et en particulier du strontium qui est entraine sur ce precipite. Il est possible ensuite de separer selectivement le strontium au moyen de resines echangeuses d'ions. L'examen de le courbe de croissance de l'activite {beta} permet de determiner les activites dues respectivement a {sup 89}Sr et {sup 90}Sr. (auteur)

Titan's greenhouse and antigreenhouse effects

Science.gov (United States)

Mckay, Christopher P.; Pollack, James B.; Courtin, Regis

1992-01-01

Thermal mechanisms active in Titan's atmosphere are discussed in a brief review of data obtained during the Voyager I flyby in 1980. Particular attention is given to the greenhouse effect (GHE) produced by atmospheric H2, N2, and CH4; this GHE is stronger than that on earth, with CH4 and H2 playing roles similar to those of H2O and CO2 on earth. Also active on Titan is an antigreenhouse effect, in which dark-brown and orange organic aerosols block incoming solar light while allowing IR radiation from the Titan surface to escape. The combination of GHE and anti-GHE leads to a surface temperature about 12 C higher than it would be if Titan had no atmosphere.

Strontium-90 migration in Hanford sediments, USA

International Nuclear Information System (INIS)

Steefel, C.I.; Yang, L.; Carroll, S.A.; Roberts, S.; Zachara, J.M.; Yabusaki, S.B.

2005-01-01

Full text of publication follows: Strontium-90 is an important risk-driving contaminant at the Hanford site in eastern Washington, USA. Disposal operations at the Hanford 100-N area released millions of liters of reactor cooling water containing high concentrations of strontium-90 into the vadose zone immediately adjacent to the Columbia River. The effectiveness of pump-and-treat methods for remediation have been questioned, largely because the strontium is strongly sorbed on subsurface sediments via ion exchange reactions and co-precipitation in carbonates. In addition, groundwater monitoring wells show a fluctuating seasonal behavior in which high strontium-90 concentrations correlate with high Columbia River stage, even while average concentrations remain approximately constant. A series of fully saturated reactive transport column experiments have been conducted to investigate the important controls on strontium migration in Hanford groundwater [1]. The experiments were designed to investigate the multicomponent cation exchange behavior of strontium in competition with the cations Na + , Ca +2 , and Mg +2 , the concentration of which differs between river water and groundwater. Reactive transport modeling of the experiments indicates that the Sr +2 selectivity coefficient becomes larger with increasing NaNO 3 concentration, a behavior also shown by the divalent cations Ca +2 and Mg +2 . A new set of column experiments investigates the effect of wetting and drying cycles on strontium- 90 sorption and migration by considering episodic flow in Hanford sediments. In addition, the effect of fluctuating aquifer chemistry as a result of changes in the Columbia River stage on Sr +2 sorption is addressed. Modeling of multicomponent reactive transport under variably saturated conditions is used to interpret the results of the episodic flow/chemistry experiments. [1] Experimental and modeling studies of the migration behavior of strontium in Hanford sediments, USA. C

Energetics of magnesium, strontium, and barium doped lanthanum gallate perovskites

International Nuclear Information System (INIS)

Cheng Jihong; Navrotsky, Alexandra

2004-01-01

LaGaO 3 perovskites doped with Sr or Ba at the La site and Mg at the Ga site were prepared by solid-state reaction or sol-gel method and characterized. Enthalpies of formation from constituent oxides at 298 K were determined by high-temperature oxide melt solution calorimetry. Energetic trends are discussed in terms of defect chemistry. As oxygen deficiency increases, formation enthalpies define three trends, LaGa 1-y Mg y O 3-δ (LGM), La 1-x Sr x Ga 1-y Mg y O 3-δ (LSGM), and La 1-x Ba x Ga 1-y Mg y O 3-δ (LBGM). They become less exothermic with increasing doping, suggesting a dominant destabilization effect from oxygen vacancies. The endothermic enthalpy of vacancy formation is 275±37, 166±18 and 138±12 kJ/mol of V O ·· for LGM, LBGM and LSGM, respectively. Tolerance factor and ion size mismatch also affect enthalpies. In terms of energetics, Sr is the best dopant for the La site and Mg for the Ga site, supporting earlier studies, including oxygen ion conductivity and computer modeling

Energetics of magnesium, strontium, and barium doped lanthanum gallate perovskites

Science.gov (United States)

Cheng, Jihong; Navrotsky, Alexandra

2004-01-01

LaGaO 3 perovskites doped with Sr or Ba at the La site and Mg at the Ga site were prepared by solid-state reaction or sol-gel method and characterized. Enthalpies of formation from constituent oxides at 298 K were determined by high-temperature oxide melt solution calorimetry. Energetic trends are discussed in terms of defect chemistry. As oxygen deficiency increases, formation enthalpies define three trends, LaGa 1- yMg yO 3- δ (LGM), La 1- xSr xGa 1- yMg yO 3- δ (LSGM), and La 1- xBa xGa 1- yMg yO 3- δ (LBGM). They become less exothermic with increasing doping, suggesting a dominant destabilization effect from oxygen vacancies. The endothermic enthalpy of vacancy formation is 275±37, 166±18 and 138±12 kJ/mol of VO·· for LGM, LBGM and LSGM, respectively. Tolerance factor and ion size mismatch also affect enthalpies. In terms of energetics, Sr is the best dopant for the La site and Mg for the Ga site, supporting earlier studies, including oxygen ion conductivity and computer modeling.

Structural, optical, photoluminescence and photocatalytic assessment of Sr-doped ZnO nanoparticles

International Nuclear Information System (INIS)

Pradeev Raj, K.; Sadaiyandi, K.; Kennedy, A.; Thamizselvi, R.

2016-01-01

ZnO nanoparticles (NPs) and Strontium doped ZnO nanoparticles (2–6 mol %) (SZ-NPs) were synthesized via Co-precipitation method. Synthesized samples were investigated by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Elemental dispersive spectroscopy (EDS), UV–visible, and Photoluminescence (PL) spectroscopy. Photocatalytic studies for Rhodamine B (RhB) dye in aqueous solution under UV–Vis radiation. XRD analysis confirms that all the samples have hexagonal wurtzite structure. The average crystallite size of the nanoparticles was in the range of 29–51 nm. From the Williamson –Hall (W-H) plot, a positive slope is inferred for pure and SZ-NPs, confirming the presence of tensile strain. SEM images reveal the synthesized NPs are in nanometer range with various shapes are observed. The presence of strontium (Sr) in the host lattice was confirmed by EDS spectroscopy. The optical analysis shows the absorption decreases on doping and shifts slightly towards the longer wavelength region. The band gap energy (Eg) decreases (3.32–3.03 eV) with the increase of Sr dopant concentration. The photoluminescence (PL) spectrum reveals the UV emission is strong near the band-edge region (NBE) (392 nm) and intrinsic defects resulted in series of Vis emissions around 400–560 nm. Kinetic studies on RhB dye indicates the degradation rate has increased with dopant concentration. The improved photocatalytic activity is observed due to the efficient charge separation, improved visible light absorption, inhibition of the electron-hole pair's recombination and better adsorptive of RhB dye molecule on the surface of SZ-NPs. Moreover, the reduction in the total organic carbon (TOC) results reveals the improved photocatalytic activity of strontium doped ZnO NPs. - Highlights: • Effective synthesis of ZnO and Sr−ZnO nanoparticles by co-precipitation method. • Samples were characterized by XRD, SEM, EDS, UV–Vis and PL technique. • Higher optical absorption and

Structural, optical, photoluminescence and photocatalytic assessment of Sr-doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Pradeev Raj, K., E-mail: pradeevraj@gmail.com [Research and Development Centre, Bharathiar University, Coimbatore, 641 046, Tamilnadu (India); Department of Physics, CSI College of Engineering, Ooty, The Nilgiris, 643 215, Tamil Nadu (India); Sadaiyandi, K. [Department of Physics, Alagappa Government Arts College, Karaikudi, Sivagangai, 630 003, Tamil Nadu (India); Kennedy, A. [Department of Physics, CSI College of Engineering, Ooty, The Nilgiris, 643 215, Tamil Nadu (India); Thamizselvi, R. [Department of Chemistry, L.R.G. Govt Arts College for Women, Tirupur, 641604, Tamil Nadu (India)

2016-11-01

ZnO nanoparticles (NPs) and Strontium doped ZnO nanoparticles (2–6 mol %) (SZ-NPs) were synthesized via Co-precipitation method. Synthesized samples were investigated by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Elemental dispersive spectroscopy (EDS), UV–visible, and Photoluminescence (PL) spectroscopy. Photocatalytic studies for Rhodamine B (RhB) dye in aqueous solution under UV–Vis radiation. XRD analysis confirms that all the samples have hexagonal wurtzite structure. The average crystallite size of the nanoparticles was in the range of 29–51 nm. From the Williamson –Hall (W-H) plot, a positive slope is inferred for pure and SZ-NPs, confirming the presence of tensile strain. SEM images reveal the synthesized NPs are in nanometer range with various shapes are observed. The presence of strontium (Sr) in the host lattice was confirmed by EDS spectroscopy. The optical analysis shows the absorption decreases on doping and shifts slightly towards the longer wavelength region. The band gap energy (Eg) decreases (3.32–3.03 eV) with the increase of Sr dopant concentration. The photoluminescence (PL) spectrum reveals the UV emission is strong near the band-edge region (NBE) (392 nm) and intrinsic defects resulted in series of Vis emissions around 400–560 nm. Kinetic studies on RhB dye indicates the degradation rate has increased with dopant concentration. The improved photocatalytic activity is observed due to the efficient charge separation, improved visible light absorption, inhibition of the electron-hole pair's recombination and better adsorptive of RhB dye molecule on the surface of SZ-NPs. Moreover, the reduction in the total organic carbon (TOC) results reveals the improved photocatalytic activity of strontium doped ZnO NPs. - Highlights: • Effective synthesis of ZnO and Sr−ZnO nanoparticles by co-precipitation method. • Samples were characterized by XRD, SEM, EDS, UV–Vis and PL technique. • Higher optical absorption

Titan Orbiter with Aerorover Mission (TOAM)

Science.gov (United States)

Sittler, Edward C.; Cooper, J. F.; Mahaffey, P.; Esper, J.; Fairbrother, D.; Farley, R.; Pitman, J.; Kojiro, D. R.; TOAM Team

2006-12-01

We propose to develop a new mission to Titan called Titan Orbiter with Aerorover Mission (TOAM). This mission is motivated by the recent discoveries of Titan, its atmosphere and its surface by the Huygens Probe, and a combination of in situ, remote sensing and radar mapping measurements of Titan by the Cassini orbiter. Titan is a body for which Astrobiology (i.e., prebiotic chemistry) will be the primary science goal of any future missions to it. TOAM is planned to use an orbiter and balloon technology (i.e., aerorover). Aerobraking will be used to put payload into orbit around Titan. The Aerorover will probably use a hot air balloon concept using the waste heat from the MMRTG 500 watts. Orbiter support for the Aerorover is unique to our approach for Titan. Our strategy to use an orbiter is contrary to some studies using just a single probe with balloon. Autonomous operation and navigation of the Aerorover around Titan will be required, which will include descent near to the surface to collect surface samples for analysis (i.e., touch and go technique). The orbiter can provide both relay station and GPS roles for the Aerorover. The Aerorover will have all the instruments needed to sample Titan’s atmosphere, surface, possible methane lakes-rivers, use multi-spectral imagers for surface reconnaissance; to take close up surface images; take core samples and deploy seismometers during landing phase. Both active and passive broadband remote sensing techniques will be used for surface topography, winds and composition measurements.

Preparation and properties of porous PMN-PZT ceramics doped with strontium

International Nuclear Information System (INIS)

Zeng Tao; Dong Xianlin; Mao Chaoliang; Chen Shutao; Chen Heng

2006-01-01

The piezoelectric and dielectric properties of lead magnesium niobate-lead zirconate titanate (PMN-PZT) ceramics were investigated as a function of density for transducer applications. A decrease in density increased elastic compliance and improved acoustic impedance matching between PMN-PZT ceramics and ambient media. The reduced dielectric constant (ε 33 ) and enhanced hydrostatic figure of merit (d h g h ) of PMN-PZT were observed with decreased density. The results showed the d h g h of PMN-PZT ceramic with density of about 5.4 g/cm 3 reached 4000 x 10 -15 m 2 /N, and the ε 33 was very close to 2000, which demonstrates that porous PMN-PZT ceramic is a promising material for transducer applications. Moreover, the low density PMN-PZT ceramics exhibited lower dielectric loss than high density PMN-PZT ceramics during the temperature from 250 deg. C to 500 deg. C

Titan's Ammonia Feature

Science.gov (United States)

Smythe, W.; Nelson, R.; Boryta, M.; Choukroun, M.

2011-01-01

NH3 has long been considered an important component in the formation and evolution of the outer planet satellites. NH3 is particularly important for Titan, since it may serve as the reservoir for atmospheric nitrogen. A brightening seen on Titan starting in 2004 may arise from a transient low-lying fog or surface coating of ammonia. The spectral shape suggests the ammonia is anhydrous, a molecule that hydrates quickly in the presence of water.

Calcium versus strontium handling by the heart muscle.

Science.gov (United States)

Hendrych, Michal; Olejnickova, Veronika; Novakova, Marie

2016-01-01

Calcium plays a crucial role in numerous processes in living systems, from both intracellular and intercellular signalling to blood clotting. Calcium can be replaced by strontium in various intracellular processes due to high level of their similarity and strontium thus may serve as a valuable tool for different experimental studies. On the other hand, strontium is also used in clinical medicine and is commonly taken to the human body with food and water. The negative cardiac side effects of strontium therapy of osteoporosis and bone metastases are well known, but still not fully explained. This fact explains enhanced interest in this element and its impact on human body. This article reviews effects of calcium and strontium on several biochemical and physiological processes, with special emphasis on cardiac muscle.

Organic chemistry on Titan: Surface interactions

Science.gov (United States)

Thompson, W. Reid; Sagan, Carl

1992-01-01

The interaction of Titan's organic sediments with the surface (solubility in nonpolar fluids) is discussed. How Titan's sediments can be exposed to an aqueous medium for short, but perhaps significant, periods of time is also discussed. Interactions with hydrocarbons and with volcanic magmas are considered. The alteration of Titan's organic sediments over geologic time by the impacts of meteorites and comets is discussed.

AVIATR - Aerial Vehicle for In-situ and Airborne Titan Reconnaissance A Titan Airplane Mission Concept

Science.gov (United States)

Barnes, Jason W.; Lemke, Lawrence; Foch, Rick; McKay, Christopher P.; Beyer, Ross A.; Radebaugh, Jani; Atkinson, David H.; Lorenz, Ralph D.; LeMouelic, Stephane; Rodriguez, Sebastien;

TSSM: The in situ exploration of Titan

Science.gov (United States)

Coustenis, A.; Lunine, J. I.; Lebreton, J. P.; Matson, D.; Reh, K.; Beauchamp, P.; Erd, C.

2008-09-01

The Titan Saturn System Mission (TSSM) mission was born when NASA and ESA decided to collaborate on two missions independently selected by each agency: the Titan and Enceladus mission (TandEM), and Titan Explorer, a 2007 Flagship study. TandEM, the Titan and Enceladus mission, was proposed as an L-class (large) mission in response to ESA's Cosmic Vision 2015-2025 Call. The mission concept is to perform remote and in situ investigations of Titan primarily, but also of Enceladus and Saturn's magentosphere. The two satellites are tied together by location and properties, whose remarkable natures have been partly revealed by the ongoing Cassini-Huygens mission. These bodies still hold mysteries requiring a complete exploration using a variety of vehicles and instruments. TSSM will study Titan as a system, including its upper atmosphere, the interactions with the magnetosphere, the neutral atmosphere, surface, interior, origin and evolution, as well as the astrobiological potential of Titan. It is an ambitious mission because its targets are two of the most exciting and challenging bodies in the Solar System. It is designed to build on but exceed the scientific and technological accomplishments of the Cassini- Huygens mission, exploring Titan and Enceladus in ways that are not currently possible (full close-up and in situ coverage over long periods of time for Titan, several close flybys of Enceladus). One overarching goal of the TSSM mission is to explore in situ the atmosphere and surface of Titan. In the current mission architecture, TSSM consists of an orbiter (under NASA's responsibility) with a large host of instruments which would perform several Enceladus and Titan flybys before stabilizing in an orbit around Titan alone, therein delivering in situ elements (a Montgolfière, or hot air balloon, and a probe/lander). The latter are being studied by ESA. The balloon will circumnavigate Titan above the equator at an altitude of about 10 km for several months. The

Diurnal variations of Titan

Science.gov (United States)

Cui, J.; Galand, M.; Yelle, R. V.; Vuitton, V.; Wahlund, J.-E.; Lavvas, P. P.; Mueller-Wodarg, I. C. F.; Kasprzak, W. T.; Waite, J. H.

2009-04-01

We present our analysis of the diurnal variations of Titan's ionosphere (between 1,000 and 1,400 km) based on a sample of Ion Neutral Mass Spectrometer (INMS) measurements in the Open Source Ion (OSI) mode obtained from 8 close encounters of the Cassini spacecraft with Titan. Though there is an overall ion depletion well beyond the terminator, the ion content on Titan's nightside is still appreciable, with a density plateau of ~700 cm-3 below ~1,300 km. Such a plateau is associated with the combination of distinct diurnal variations of light and heavy ions. Light ions (e.g. CH5+, HCNH+, C2H5+) show strong diurnal variation, with clear bite-outs in their nightside distributions. In contrast, heavy ions (e.g. c-C3H3+, C2H3CNH+, C6H7+) present modest diurnal variation, with significant densities observed on the nightside. We propose that the distinctions between light and heavy ions are associated with their different chemical loss pathways, with the former primarily through "fast" ion-neutral chemistry and the latter through "slow" electron dissociative recombination. The INMS data suggest day-to-night transport as an important source of ions on Titan's nightside, to be distinguished from the conventional scenario of auroral ionization by magnetospheric particles as the only ionizing source on the nightside. This is supported by the strong correlation between the observed night-to-day ion density ratios and the associated ion lifetimes. We construct a time-dependent ion chemistry model to investigate the effects of day-to-night transport on the ionospheric structures of Titan. The predicted diurnal variation has similar general characteristics to those observed, with some apparent discrepancies which could be reconciled by imposing fast horizontal thermal winds in Titan's upper atmosphere.

Effect of La doping on crystalline orientation, microstructure and dielectric properties of PZT thin films

Energy Technology Data Exchange (ETDEWEB)

Xu, Wencai; Li, Qi; Wang, Xing [Dalian Univ. of Technology, Dalian (China). School of Mechanical Engineering; Yin, Zhifu [Jilin Univ., Changchun (China). Faculty of the School of Mechanical Science and Engineering; Zou, Helin [Dalian Univ. of Technology, Dalian (China). Key Lab. for Micro/Nano Systems and Technology

2017-11-01

Lanthanum (La)-modified lead zirconate titanate (PLZT) thin films with doping concentration from 0 to 5 at.-% have been fabricated by sol-gel methods to investigate the effects of La doping on crystalline orientation, microstructure and dielectric properties of the modified films. The characterization of PLZT thin films were performed by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and precision impedance analysis. XRD analysis showed that PLZT films with La doping concentration below 4 at.-% exhibited (100) preferred orientation. SEM results indicated that PLZT films presented dense and columnar microstructures when La doping concentration was less than 3 at.-%, while the others showed columnar microstructures only at the bottom of the cross section. The maximum dielectric constant (1502.59 at 100 Hz) was obtained in a 2 at.-% La-doped film, which increased by 53.9 % compared with undoped film. Without introducing a seed layer, (100) oriented PLZT thin films were prepared by using conventional heat treatment process and adjusting La doping concentration.

Kinetics of strontium sorption in calcium phosphate

International Nuclear Information System (INIS)

Bacic, S.; Komarov, V.F.; Vukovic, Z.

1989-01-01

Kinetics of strontium sorption by highly dispersed solids: tricalcium phosphate (Ca 3 (PO 4 ) 2 , TCP) and hydroxyapatite (Ca 5 (PO 4 ) 3 )H, HAP) were investigated. Analysis of sorption data was made taking into consideration composition and morphology of ultra micro particles. Conclusion is that the isomorphous strontium impurity is structurally sensitive element for calcium phosphate. It was determined that the beginning of strontium desorption corresponds to the beginning of transformation of the TCP - HAP (author)

Measurement of strontium 90 in the rain fall-out

International Nuclear Information System (INIS)

Suratman; Soedyartomo; Suhartono.

1976-01-01

The procedure of radioactivity measurement of strontium 90 in the rain fallout as well as the measurement of the fallout gross beta activity have been studied. In the preliminary study strontium 90 is separated from other cations especially fission products by fuming nitric acid, and radioactivity measurement is carried out in the form of strontium oxalate. Data of radioactivity measurement of strontium 90 and the gross beta activity in the fallout are given. (author)

The coprecipitation of strontium with hydroxyapatite

International Nuclear Information System (INIS)

Fujino, Osamu

1975-01-01

The distribution behavior of the strontium ion between hydroxyapatite and the parent solution was investigated. The hydroxyapatite was formed by the extremely slow addition of diammonium hydrogenphosphate to solutions of calcium and strontium nitrate buffered with ethylenediamine at 80 0 C. The precipitate yielded a typical X-ray diffraction pattern of hydroxyapatite and had a composition in which the Ca/P molar ratio was 1.67 at pH 6.80. The strontium ion was coprecipitated in the apatite, obeying the Doerner and Hoskins logarithnmic distribution law. The distribution coefficient was scarcely affected by the strontium concentration on the pH value in the parent solution, and had a value of 0.26+-0.02 at 80 0 C. On the other hand, the apparent distribution coefficient was a little affected by such organic anions as acetate, citrate, lactate, glycinate, and glutamate ions. The lattice constants of the precipitates prepared in the research were measured in order to confirm the formation of the solid solutions. (auth.)

Conductivity of A- and B-site doped LaAlO3, LaGaO3, LaScO3 and LaInO3 perovskites

DEFF Research Database (Denmark)

Lybye, D.; Poulsen, F.W.; Mogensen, Mogens Bjerg

2000-01-01

The conductivity of the materials LaAlO3, LaGaO3, LaScO3 and LaInO3 all doped with 10% strontium on the A-site and 10% magnesium at the B-site has been measured at different temperatures and oxygen partial pressures. The doped LaGaO3 is found to be an almost pure ionic conductor with a conductivi...

Amino acidis derived from Titan tholins

Science.gov (United States)

Khare, Bishun N.; Sagan, Carl; Ogino, Hiroshi; Nagy, Bartholomew; Er, Cevat

1986-01-01

The production of amino acids by acid treatment of Titan tholin is experimentally investigated. The synthesis of Titan tholin and the derivatization of amino acids to N-trifluoroacetyl isopropyl esters are described. The gas chromatography/mass spectroscopy analysis of the Titan tholins reveals the presence of glycine, alpha and beta alainine, and aspartic acid, and the total yield of amino acids is about 0.01.

Electrical Properties of Thin-Film Capacitors Fabricated Using High Temperature Sputtered Modified Barium Titanate

Directory of Open Access Journals (Sweden)

Robert Mamazza

2012-04-01

Full Text Available Simple thin-film capacitor stacks were fabricated from sputter-deposited doped barium titanate dielectric films with sputtered Pt and/or Ni electrodes and characterized electrically. Here, we report small signal, low frequency capacitance and parallel resistance data measured as a function of applied DC bias, polarization versus applied electric field strength and DC load/unload experiments. These capacitors exhibited significant leakage (in the range 8–210 μA/cm2 and dielectric loss. Measured breakdown strength for the sputtered doped barium titanate films was in the range 200 kV/cm −2 MV/cm. For all devices tested, we observed clear evidence for dielectric saturation at applied electric field strengths above 100 kV/cm: saturated polarization was in the range 8–15 μC/cm2. When cycled under DC conditions, the maximum energy density measured for any of the capacitors tested here was ~4.7 × 10−2 W-h/liter based on the volume of the dielectric material only. This corresponds to a specific energy of ~8 × 10−3 W-h/kg, again calculated on a dielectric-only basis. These results are compared to those reported by other authors and a simple theoretical treatment provided that quantifies the maximum energy that can be stored in these and similar devices as a function of dielectric strength and saturation polarization. Finally, a predictive model is developed to provide guidance on how to tailor the relative permittivities of high-k dielectrics in order to optimize their energy storage capacities.

Ion exchange of strontium on synthetic hydroxyapatite

International Nuclear Information System (INIS)

Lazic, S.; Vukovic, Z.

1991-01-01

Adsorption of strontium ions on synthetic hydroxyapatite was examined using both batch and column methods. The apatite was prepared from aqueous solutions and characterized by standard analytical methods. The sample obtained had characteristics of well crystallized stoichiometric hydroxyapatite. The experimental data for sorption of strontium can be very well fitted with Langmuir's adsorption isotherm. It was found that sorption occurs by an ion exchange reaction between strontium ions in solution and calcium ions in apatite. (author) 14 refs.; 5 figs.; 1 tab

Bismuth titanate nanorods and their visible light photocatalytic properties

International Nuclear Information System (INIS)

Pei, L.Z.; Liu, H.D.; Lin, N.; Yu, H.Y.

2015-01-01

Highlights: • Bismuth titanate nanorods have been synthesized by a simple hydrothermal process. • The size of bismuth titanate nanorods can be controlled by growth conditions. • Bismuth titanate nanorods show good photocatalytic activities of methylene blue and Rhodamine B. - Abstract: Bismuth titanate nanorods have been prepared using a facile hydrothermal process without additives. The bismuth titanate products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM) and UV-vis diffusion reflectance spectrum. XRD pattern shows that the bismuth titanate nanorods are composed of cubic Bi 2 Ti 2 O 7 phase. Electron microscopy images show that the length and diameter of the bismuth titanate nanorods are 50-200 nm and 2 μm, respectively. Hydrothermal temperature and reaction time play important roles on the formation and size of the bismuth titanate nanorods. UV-vis diffusion reflectance spectrum indicates that bismuth titanate nanorods have a band gap of 2.58 eV. The bismuth titanate nanorods exhibit good photocatalytic activities in the photocatalytic degradation of methylene blue (MB) and Rhodamine B (RB) under visible light irradiation. The bismuth titanate nanorods with cubic Bi 2 Ti 2 O 7 phase are a promising candidate as a visible light photocatalyst

Hubble Observes Surface of Titan

Science.gov (United States)

1994-01-01

Scientists for the first time have made images of the surface of Saturn's giant, haze-shrouded moon, Titan. They mapped light and dark features over the surface of the satellite during nearly a complete 16-day rotation. One prominent bright area they discovered is a surface feature 2,500 miles across, about the size of the continent of Australia.Titan, larger than Mercury and slightly smaller than Mars, is the only body in the solar system, other than Earth, that may have oceans and rainfall on its surface, albeit oceans and rain of ethane-methane rather than water. Scientists suspect that Titan's present environment -- although colder than minus 289 degrees Fahrenheit, so cold that water ice would be as hard as granite -- might be similar to that on Earth billions of years ago, before life began pumping oxygen into the atmosphere.Peter H. Smith of the University of Arizona Lunar and Planetary Laboratory and his team took the images with the Hubble Space Telescope during 14 observing runs between Oct. 4 - 18. Smith announced the team's first results last week at the 26th annual meeting of the American Astronomical Society Division for Planetary Sciences in Bethesda, Md. Co-investigators on the team are Mark Lemmon, a doctoral candidate with the UA Lunar and Planetary Laboratory; John Caldwell of York University, Canada; Larry Sromovsky of the University of Wisconsin; and Michael Allison of the Goddard Institute for Space Studies, New York City.Titan's atmosphere, about four times as dense as Earth's atmosphere, is primarily nitrogen laced with such poisonous substances as methane and ethane. This thick, orange, hydrocarbon haze was impenetrable to cameras aboard the Pioneer and Voyager spacecraft that flew by the Saturn system in the late 1970s and early 1980s. The haze is formed as methane in the atmosphere is destroyed by sunlight. The hydrocarbons produced by this methane destruction form a smog similar to that found over large cities, but is much thicker

Impact of ZnO substitution on magnetic response and microwave absorption capability of strontium-natural nanoferrites

Directory of Open Access Journals (Sweden)

W. Widanarto

2015-01-01

Full Text Available Ferrite being a compound derived from iron oxides including magnetite and hematite possesses similar properties as ceramics which are hard and brittle. Certainly, the mounting demand for electronics has been a major factor driving the exponential growth of ferrite based materials. ZnO doped strontium-natural nanoferrites of composition (80 − xFe2O3:xZnO:20SrCO3, where x = 0, 10, 20 mol% are synthesized and sintered via the solid state reaction scheme. Samples are characterized by SEM, XRD, VSM, and VNA measurements to determine the impact of ZnO contents’ variation on the surface morphology, structure, magnetic and microwave absorption properties. The Nicolson–Ross–Weir method is applied to evaluate samples’ reflection loss. The average grain size of the strontium ferrite is found to reduce with the increase in ZnO concentration. Materials sintered at 1100 °C without ZnO incorporation are composed of hexagonal SrFe12O19. Meanwhile, the addition of ZnO produces cubic ZnFe2O4 and SrFeO2 phases. Insertion of ZnO results in reduction of magnetic parameters and reflection loss. Furthermore, the anisotropy magnetic field of strontium natural ferrites displays a rapid drop from 350 kA/m to 79.6 kA/m with the increase in ZnO. Strontium ferrite containing 20 mol% of ZnO exhibits superior microwave absorption with reflection loss within −45 dB to −55.94 dB in the frequency range of 7–13 GHz. This facilely synthesized a new class of materials which is believed to be economically promising for microwave absorption applications in the GHz range.

Synthesis and characterization of strontium molybdate doped with copper, cobalt and zinc for purposes photocatalytic; Sintese e caracterizacao do molibdato de estroncio dopado com cobre, cobalto e zinco para fins fotocataliticos

Energy Technology Data Exchange (ETDEWEB)

Dutra, F.B.; Silva, M.M.S.; Moriyama, A.L.L.; Souza, C.P., E-mail: faby_qui@hotmail.com [Universidade Federal do Rio Grande do Norte (LAMNRC/UFRN), Natal, RN (Brazil). Lab. de Materiais Nanoestruturados e Reatores Catalicos

2016-07-01

The broad concerns of contemporary society with environmental problems requires legislation and more effective techniques for wastewater treatment. In recent years, ceramic materials that have properties such as high melting points and high stability have been receiving great emphasis in several studies in particular heterogeneous photocatalysis, rapid and efficient method for the complete mineralization of contaminants. In this context, the present work deals with the synthesis and characterization of molybdate Strontium (SrMoO4) doped with copper, cobalt and zinc for the purpose of photocatalytic studies. The compounds were synthesized by complexation method EDTA / Citrate basic medium. The powders were characterized by Thermogravimetric Analysis (TG), X-Ray Diffraction (XRD), Particle size distribution by laser diffraction, Spectroscopy in the UV-Visible region, Energy Dispersive Spectroscopy (EDS) and Scanning Electron Microscopy (SEM), showing promising results as the crystalline phase of development and potential uses for the purpose of heterogeneous photocatalysis. (author)

Fabrication and characterization of strontium incorporated 3-D bioactive glass scaffolds for bone tissue from biosilica

Energy Technology Data Exchange (ETDEWEB)

Özarslan, Ali Can, E-mail: alicanozarslan@gmail.com; Yücel, Sevil, E-mail: syucel@yildiz.edu.tr

2016-11-01

Bioactive glass scaffolds that contain silica are high viable biomaterials as bone supporters for bone tissue engineering due to their bioactive behaviour in simulated body fluid (SBF). In the human body, these materials help inorganic bone structure formation due to a combination of the particular ratio of elements such as silicon (Si), calcium (Ca), sodium (Na) and phosphorus (P), and the doping of strontium (Sr) into the scaffold structure increases their bioactive behaviour. In this study, bioactive glass scaffolds were produced by using rice hull ash (RHA) silica and commercial silica based bioactive glasses. The structural properties of scaffolds such as pore size, porosity and also the bioactive behaviour were investigated. The results showed that undoped and Sr-doped RHA silica-based bioactive glass scaffolds have better bioactivity than that of commercial silica based bioactive glass scaffolds. Moreover, undoped and Sr-doped RHA silica-based bioactive glass scaffolds will be able to be used instead of undoped and Sr-doped commercial silica based bioactive glass scaffolds for bone regeneration applications. Scaffolds that are produced from undoped or Sr-doped RHA silica have high potential to form new bone for bone defects in tissue engineering. - Highlights: • Production of 3-D bioactive glass scaffolds from different silica sources • The effect of biosilica from rice hull ash on the bioactive glass scaffold • Sr additive impact on the bioactivity and biodegradability properties of scaffolds.

The rotation of Titan and Ganymede

Science.gov (United States)

Van Hoolst, Tim; Coyette, Alexis; Baland, Rose-Marie; Trinh, Antony

2016-10-01

The rotation rates of Titan and Ganymede, the largest satellites of Saturn and Jupiter, are on average equal to their orbital mean motion. Here we discuss small deviations from the average rotation for both satellites and evaluate the polar motion of Titan induced by its surface fluid layers. We examine different causes at various time scales and assess possible consequences and the potential of using librations and polar motion as probes of the interior structure of the satellites.The rotation rate of Titan and Ganymede cannot be constant on the orbital time scale as a result of the gravitational torque of the central planet acting on the satellites. Titan is moreover expected to show significant polar motion and additional variations in the rotation rate due to angular momentum exchange with the atmosphere, mainly at seasonal periods. Observational evidence for deviations from the synchronous state has been reported several times for Titan but is unfortunately inconclusive. The measurements of the rotation variations are based on determinations of the shift in position of Cassini radar images taken during different flybys. The ESA JUICE (JUpiter ICy moons Explorer) mission will measure the rotation variations of Ganymede during its orbital phase around the satellite starting in 2032.We report on different theoretical aspects of the librations and polar motion. We consider the influence of the rheology of the ice shell and take into account Cassini measurements of the external gravitational field and of the topography of Titan and similar Galileo data about Ganymede. We also evaluate the librations and polar motion induced by Titan's hydrocarbon seas and use the most recent results of Titan's atmosphere dynamics. We finally evaluate the potential of rotation variations to constrain the satellite's interior structure, in particular its ice shell and ocean.

Future Exploration of Titan and Enceladus

Science.gov (United States)

Matson, D. L.; Coustenis, A.; Lunine, J.; Lebreton, J.; Reh, K.; Beauchamp, P.

2009-05-01

The future exploration of Titan and Enceladus has become very important for the planetary community. The study conducted last year of the Titan Saturn System Mission (TSSM) led to an announcement in which ESA and NASA prioritized future OPF missions, stating that TSSM is planned after EJSM (for details see http://www.lpi.usra.edu/opag/). TSSM consists of a TSSM Orbiter that would carry two in situ elements: the Titan Montgolfiere hot air balloon and the Titan Lake Lander. The mission could launch in the 2023-2025 timeframe on a trajectory to arrive ~9 years later for a 4-year mission in the Saturn system. Soon after arrival at Saturn, the montgolfiere would be delivered to Titan to begin its mission of airborne, scientific observations of Titan from an altitude of about 10 km. The montgolfiere would have a Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) power system and would be designed to last at least 6-12 months in Titan's atmosphere. With the predicted winds and weather, that would be sufficient to circumnavigate the globe! On a subsequent fly-by, the TSSM orbiter would release the Lake Lander on a trajectory toward Titan for a targeted entry. It would descend through the atmosphere making scientific measurements, much like Huygens did, and then land and float on one of Titan's seas. This would be its oceanographic phase, making a physical and chemical assessment of the sea. The Lake Lander would operate 8-10 hours until its batteries become depleted. Following the delivery of the in situ elements, the TSSM orbiter would explore the Saturn system via a 2-year tour that includes in situ sampling of Enceladus' plumes as well as Titan flybys. After the Saturn system tour, the TSSM orbiter would enter orbit around Titan for a global survey phase. Synergistic and coordinated observations would be carried out between the TSSM orbiter and the in situ elements. The scientific requirements were developed by the international TSSM Joint Science Definition

Clash of the Titans

Science.gov (United States)

Subramaniam, Karthigeyan

2010-01-01

WebQuests and the 5E learning cycle are titans of the science classroom. These popular inquiry-based strategies are most often used as separate entities, but the author has discovered that using a combined WebQuest and 5E learning cycle format taps into the inherent power and potential of both strategies. In the lesson, "Clash of the Titans,"…

Influence of defect mobility on electrostrain in acceptor-doped Ba{sub 0.80}Sr{sub 0.20}TiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Vani, K.; Kumar, Viswanathan, E-mail: vkumar10@yahoo.com [Center for Materials for Electronics Technology, Scientific Society, Department of Information Technology, Ministry of Communications and Information Technology, Government of India, Thrissur 680 581, Kerala (India)

2012-12-15

This study reports significant differences in the defect-mediated electrostrain in B-site trivalent ions (Fe{sup 3+} and Mn{sup 3+}) doped Barium titanate based system. Electron Paramagnetic Resonance (EPR) Spectroscopy has been employed as a structural probe for understanding the symmetry of defects. Differences in the reorientation of the defect dipoles have been correlated with the electrostrain. Mechanism for the higher strain in Mn-doped system has also been explained.

TITAN'S TRANSPORT-DRIVEN METHANE CYCLE

International Nuclear Information System (INIS)

Mitchell, Jonathan L.

2012-01-01

The mechanisms behind the occurrence of large cloud outbursts and precipitation on Titan have been disputed. A global- and annual-mean estimate of surface fluxes indicated only 1% of the insolation, or ∼0.04 W m –2 , is exchanged as sensible and/or latent fluxes. Since these fluxes are responsible for driving atmospheric convection, it has been argued that moist convection should be quite rare and precipitation even rarer, even if evaporation globally dominates the surface-atmosphere energy exchange. In contrast, climate simulations indicate substantial cloud formation and/or precipitation. We argue that the top-of-atmosphere (TOA) radiative imbalance is diagnostic of horizontal heat transport by Titan's atmosphere, and thus constrains the strength of the methane cycle. Simple calculations show the TOA radiative imbalance is ∼0.5-1 W m –2 in Titan's equatorial region, which implies 2-3 MW of latitudinal heat transport by the atmosphere. Our simulation of Titan's climate suggests this transport may occur primarily as latent heat, with net evaporation at the equator and net accumulation at higher latitudes. Thus, the methane cycle could be 10-20 times previous estimates. Opposing seasonal transport at solstices, compensation by sensible heat transport, and focusing of precipitation by large-scale dynamics could further enhance the local, instantaneous strength of Titan's methane cycle by a factor of several. A limited supply of surface liquids in regions of large surface radiative imbalance may throttle the methane cycle, and if so, we predict more frequent large storms over the lakes district during Titan's northern summer.

Radiation stability of sodium titanate ion exchange materials

International Nuclear Information System (INIS)

Kenna, B.T.

1980-02-01

Sodium titanate and sodium titanate loaded macroreticular resin are being considered as ion exchangers to remove 90 Sr and actinides from the large volume of defense waste stored at Hanford Site in Washington. Preliminary studies to determine the radiation effect on Sr +2 and I - capacity of these ion-exchange materials were conducted. Samples of sodium titanate powder, sodium titanate loaded macroreticular resin, as well as the nitrate form of macroreticular anion resin were irradiated with up to 2 x 10 9 Rads of 60 Co gamma rays. Sodium titanate cation capacity decreased about 50% while the sodium titanate loaded macroeticular resin displayed a dramatic decrease in cation capacity when irradiated with 10 8 -10 9 Rad. The latter decrease is tentatively ascribed to radiation damage to the organic portion which subsequently inhibits interaction with the contained sodium titanate. The anion capacity of both macroreticular resin and sodium titanate loaded macroreticular resin exhibited significant decreases with increasing radiation exposure. These results suggest that consideration should be given to the potential effects of radiation degradation if column regeneration is to be used. 5 figures, 2 tables

A combined cesium-strontium extraction/recovery process

International Nuclear Information System (INIS)

Horwitz, E.P.; Dietz, M.L.; Jensen, M.P.

1996-01-01

A new solvent extraction process for the simultaneous extraction of cesium and strontium from acidic nitrate media is described. This process uses a solvent formulation comprised of 0.05 M di-t-butylcyclohexano-18-crown-6 (DtBuCH18C6), 0.1 M Crown 100' (a proprietary, cesium-selective derivative of dibenzo-18-crown-6), 1.2 M tributyl phosphate (TBP), and 5% (v/v) lauryl nitrile in an isoparaffinic hydrocarbon diluent. Distribution ratios for cesium and strontium from 4 M nitric acid are 4.13 and 3.46, respectively. A benchtop batch countercurrent extraction experiment indicates that >98% of the cesium and strontium initially present in the feed solution can be removed in only four extraction stages. Through proper choice of extraction and strip conditions, extracted cesium and strontium can be recovered either together or individually

Materials system for intermediate temperature solid oxide fuel cells based on doped lanthanum-gallate electrolyte

Science.gov (United States)

Gong, Wenquan

2005-07-01

The objective of this work was to identify a materials system for intermediate temperature solid oxide fuel cells (IT-SOFCs). Towards this goal, alternating current complex impedance spectroscopy was employed as a tool to study electrode polarization effects in symmetrical cells employing strontium and magnesium doped lanthanum gallate (LSGM) electrolyte. Several cathode materials were investigated including strontium doped lanthanum manganite (LSM), Strontium and iron doped lanthanum cobaltate (LSCF), LSM-LSGM, and LSCF-LSGM composites. Investigated Anode materials included nickel-gadolinium or lanthanum doped cerium oxide (Ni-GDC, or Ni-LDC) composites. The ohmic and the polarization resistances of the symmetrical cells were obtained as a function of temperature, time, thickness, and the composition of the electrodes. Based on these studies, the single phase LSM electrode had the highest polarization resistance among the cathode materials. The mixed-conducting LSCF electrode had polarization resistance orders of magnitude lower than that of the LSM-LSGM composite electrodes. Although incorporating LSGM in the LSCF electrode did not reduce the cell polarization resistance significantly, it could reduce the thermal expansion coefficient mismatch between the LSCF electrodes and LSGM electrolyte. Moreover, the polarization resistance of the LSCF electrode decreased asymptotically as the electrode thickness was increased thus suggesting that the electrode thickness needed not be thicker than this asymptotic limit. On the anode side of the IT-SOFC, Ni reacted with LSGM electrolyte, and lanthanum diffusion occurred from the LSGM electrolyte to the GDC barrier layer, which was between the LSGM electrolyte and the Ni-composite anode. However, LDC served as an effective barrier layer. Ni-LDC (70 v% Ni) anode had the largest polarization resistance, while all other anode materials, i.e. Ni-LDC (50 v% Ni), Ni-GDC (70 v% NO, and Ni-GDC (50 v% Ni), had similar polarization

Chemical investigation of Titan and Triton tholins

Science.gov (United States)

Mcdonald, Gene D.; Thompson, W. R.; Heinrich, Michael; Khare, Bishun N.; Sagan, Carl

1994-01-01

We report chromatographic and spectroscopic analyses of both Titan and Triton tholins, organic solids made from the plasma irradiation of 0.9:0.1 and 0.999:0.001 N2/CH4 gas mixtures, respectively. The lower CH4 mixing ratio leads to a nitrogen-richer tholin (N/C greater than 1), probably including nitrogen heterocyclic compounds. Unlike Titan tholin, bulk Triton tholin is poor in nitriles. From high-pressure liquid chromatography, ultraviolet and infrared spectroscopy, and molecular weight estimation by gel filtration chromatography, we conclude that (1) several H2O-soluble fractions, each with distinct UV and IR spectral signatures, are present, (2) these fractions are not identical in the two tholins, (3) the H2O-soluble fractions of Titan tholins do not contain significant amounts of nitriles, despite the major role of nitriles in bulk Titan tholin, and (4) the H2O-soluble fractions of both tholins are mainly molcules containing about 10 to 50 (C + N) atoms. We report yields of amino acids upon hydrolysis of Titan and Triton tholins. Titan tholin is largely insoluble in the putative hydrocarbon lakes or oceans on Titan, but can yield the H2O-soluble species investigated here upon contact with transient (e.g., impact-generated) liquid water.

Strontium clusters: electronic and geometry shell effects

DEFF Research Database (Denmark)

Lyalin, Andrey G.; Solov'yov, Ilia; Solov'yov, Andrey V.

2008-01-01

charged strontium clusters consisting of up to 14 atoms, average bonding distances, electronic shell closures, binding energies per atom, and spectra of the density of electronic states (DOS). It is demonstrated that the size-evolution of structural and electronic properties of strontium clusters...... is governed by an interplay of the electronic and geometry shell closures. Influence of the electronic shell effects on structural rearrangements can lead to violation of the icosahedral growth motif of strontium clusters. It is shown that the excessive charge essentially affects the optimized geometry...

Leaching of strontium sulfide from produced clinker in conversion furnace

International Nuclear Information System (INIS)

Ghorbanian, S. A.; Salehpour, A. R.; Radpour, S. R.

2009-01-01

Iran is rich in mineral resources one of which is mineral Celestine. Basing on current estimations, the capacity of mineral Celestine is over two million tons, 75-95% of which is strontium sulfate. However; in industries such as Color cathode Ray Tubes, pyrochemical processes, ceramics, paint production, zinc purification processes; strontium sulfate is not a direct feed, rather it is largely consumed in the form of strontium carbonate. Two conventional methods are used to produce strontium carbonate from the sulfate; that is direct reaction and black ash methods. Strontium sulfide, as an intermediate component has a key role in black ash process including strontium sulfate reduction by coke, hence producing and leaching the strontium sulfide by hot water. Finally the reaction of strontium sulfate with sodium carbonate lead to strontium carbonate. In this paper, a system was designed to analyze and optimize the process parameters of strontium sulfide production which is less expensive and available solvent in water. Fundamentally, when strontium sulfide becomes in contact with strontium sulfate; Sr(SH) 2 , and Sr(OH) 2 , are produced. The solubility of strontium sulfide depends on water temperature and the maximum solubility achieved at 90 d egree C . The results showed that in the experimental scale, at water to SrS ratio of 6; they sediment for 45 minutes at 95 d egree C in five operational stages; the separation of 95 and 97.1 percent of imported SrS is possible in effluent of fourth and fifth stages, respectively. Thus; four leaching stages could be recommended for pilot scale plants. Also, the results show that at water to SrS ratio of 8, 40 minutes sedimentation at 85-95 d egree C in one operational stage, the separation of 95 percent separation of inputted SrS, is possible. Solvent leaching process is continued till no smell of sulfur components is felt. It could be used as a key role to determine the number of leaching stages in experiments. Finally, the

Magnetic and microwave absorption properties of rare earth ions (Sm{sup 3+}, Er{sup 3+}) doped strontium ferrite and its nanocomposites with polypyrrole

Energy Technology Data Exchange (ETDEWEB)

Luo, Juhua, E-mail: luojuhua@163.com [School of Materials Engineering, Yancheng Institute of Technology, Yancheng 224051 (China); Xu, Yang; Mao, Hongkai [School of Material Science and Engineering, Jiangsu University, Zhenjiang 212013 (China)

2015-05-01

M-type strontium ferrite substituted by RE (RE=Sm{sup 3+}, Er{sup 3+}) were prepared via a sol–gel method. Polypyrrole (PPy)/ferrite nanocomposites (with 20 wt% ferrite) were prepared by in situ polymerization method in the presence of ammonium persulfate. Effect of the substituted RE ions on structure, magnetic properties and microwave absorption properties were investigated by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and vector network analyzer. All XRD patterns show the single phase of strontium hexaferrite without other intermediate phases. The crystallite size of synthesized particle is within the range of 22.2–38.1 nm. The structural in character of the composites were investigated with FT-IR analysis. It shows that the ferrite successfully packed by PPy. TEM photographs show that the particle size had grown up to 50–100 nm after coating with PPy. In the magnetization for the PPy/SrSm{sub 0.3}Fe{sub 11.7}O{sub 19} (SrEr{sub 0.3}Fe{sub 11.7}O{sub 19}) composites, the coercivity (H{sub c}) of the composites both increased compared with the undoped composite while the saturation magnetization (M{sub s}) appeared opposite change with different RE ions. Considering the electromagnetic loss and impedance matching comprehensively, the Er-doped ferrite/PPy composite got the better microwave absorption performance with the maximum RL value of −24.01 dB in 13.8 GHz at 3.0 mm. And its width (<−10 dB) has reached 7.2 GHz which has covered the whole Ku band. - Highlights: • The influence of RE ions on the structure of PPy/SrRE{sub 0.3}Fe{sub 11.7}O{sub 19} is discussed. • The influence of RE ions on the magnetic properties of PPy/SrRE{sub 0.3}Fe{sub 11.7}O{sub 19} is discussed. • The influence of RE ions on electromagnetic losses of PPy/SrRE{sub 0.3}Fe{sub 11.7}O{sub 19} is discussed. • PPy/SrEr{sub 0.3}Fe{sub 11.7}O{sub 19} possessed the excellent absorption property.

Molybdate Based Ceramic Negative-Electrode Materials for Solid Oxide Cells

DEFF Research Database (Denmark)

Graves, Christopher R.; Reddy Sudireddy, Bhaskar; Mogensen, Mogens Bjerg

2010-01-01

Novel molybdate materials with varying Mo valence were synthesized as possible negative-electrode materials for solid oxide cells. The phase, stability, microstructure and electrical conductivity were characterized. The electrochemical activity for H2O and CO2 reduction and H2 and CO oxidation...... enhanced the electrocatalytic activity and electronic conductivity. The polarization resistances of the best molybdates were two orders of magnitude lower than that of donor-doped strontium titanates. Many of the molybdate materials were significantly activated by cathodic polarization, and they exhibited...... higher performance for cathodic (electrolysis) polarization than for anodic (fuel cell) polarization, which makes them especially interesting for use in electrolysis electrodes. ©2010 COPYRIGHT ECS - The Electrochemical Society...

The Exploration of Titan and the Saturnian System

Science.gov (United States)

Coustenis, Athena

The exploration of the outer solar system and in particular of the giant planets and their environments is an on-going process with the Cassini spacecraft currently around Saturn, the Juno mission to Jupiter preparing to depart and two large future space missions planned to launch in the 2020-2025 time frame for the Jupiter system and its satellites (Europa and Ganymede) on the one hand, and the Saturnian system and Titan on the other hand [1,2]. Titan, Saturn's largest satellite, is the only other object in our Solar system to possess an extensive nitrogen atmosphere, host to an active organic chemistry, based on the interaction of N2 with methane (CH4). Following the Voyager flyby in 1980, Titan has been intensely studied from the ground-based large telescopes (such as the Keck or the VLT) and by artificial satellites (such as the Infrared Space Observatory and the Hubble Space Telescope) for the past three decades. Prior to Cassini-Huygens, Titan's atmospheric composition was thus known to us from the Voyager missions and also through the explorations by the ISO. Our perception of Titan had thus greatly been enhanced accordingly, but many questions remained as to the nature of the haze surrounding the satellite and the composition of the surface. The recent revelations by the Cassini-Huygens mission have managed to surprise us with many discoveries [3-8] and have yet to reveal more of the interesting aspects of the satellite. The Cassini-Huygens mission to the Saturnian system has been an extraordinary success for the planetary community since the Saturn-Orbit-Insertion (SOI) in July 2004 and again the very successful probe descent and landing of Huygens on January 14, 2005. One of its main targets was Titan. Titan was revealed to be a complex world more like the Earth than any other: it has a dense mostly nitrogen atmosphere and active climate and meteorological cycles where the working fluid, methane, behaves under Titan conditions the way that water does on

Seasonal Changes in Titan's Meteorology

Science.gov (United States)

Turtle, E. P.; DelGenio, A. D.; Barbara, J. M.; Perry, J. E.; Schaller, E. L.; McEwen, A. S.; West, R. A.; Ray, T. L.

2011-01-01

The Cassini Imaging Science Subsystem has observed Titan for 1/4 Titan year, and we report here the first evidence of seasonal shifts in preferred locations of tropospheric methane clouds. South \\polar convective cloud activity, common in late southern summer, has become rare. North \\polar and northern mid \\latitude clouds appeared during the approach to the northern spring equinox in August 2009. Recent observations have shown extensive cloud systems at low latitudes. In contrast, southern mid \\latitude and subtropical clouds have appeared sporadically throughout the mission, exhibiting little seasonality to date. These differences in behavior suggest that Titan s clouds, and thus its general circulation, are influenced by both the rapid temperature response of a low \\thermal \\inertia surface and the much longer radiative timescale of Titan s cold thick troposphere. North \\polar clouds are often seen near lakes and seas, suggesting that local increases in methane concentration and/or lifting generated by surface roughness gradients may promote cloud formation. Citation

Maintenance procedures for the TITAN-I and TITAN-II reversed field pinch reactors

International Nuclear Information System (INIS)

Grotz, S.P.; Duggan, W.; Krakowski, R.; Najmabadi, F.; Wong, C.P.C.

1989-01-01

The TITAN reactor is a compact, high-power-density (neutron wall loading 18 MW/m 2 ) machine, based on the reversed-field-pinch (RFP) confinement concept. Two designs for the fusion power core have been examined: TITAN-I is based on a self-cooled lithium loop with a vanadium-alloy structure for the first wall, blanket and shield; and TITAN-II is based on an aqueous loop-in-pool design with a LiNO 3 solution as the coolant and breeder. The compact design of the TITAN fusion power core, (FPC) reduces the system to a few small and relatively low mass components, making toroidal segmentation of the FPC unnecessary. A single-piece maintenance procedure is possible. The potential advantages of single-piece maintenance procedures are: (1) Short period of down time; (2) improved reliability; (3) no adverse effects resulting from unequal levels of irradiation; and (4) ability to continually modify the FPC design. Increased availability can be expected from a fully pre-tested, single-piece FPC. Pre-testing of the FPC throughout the assembly process and prior to installation into the reactor vault is discussed. (orig.)

Growth of strontium oxalate crystals in agar–agar gel

Indian Academy of Sciences (India)

Growth of strontium oxalate crystals in agar–agar gel. P V DALAL. ∗ and K B SARAF. Postgraduate Department of Physics, Pratap College, Amalner 425 401, India. MS received 16 March 2008; revised 5 April 2010. Abstract. Single crystals of strontium oxalate have been grown by using strontium chloride and oxalic acid in.

The tides of Titan.

Science.gov (United States)

Iess, Luciano; Jacobson, Robert A; Ducci, Marco; Stevenson, David J; Lunine, Jonathan I; Armstrong, John W; Asmar, Sami W; Racioppa, Paolo; Rappaport, Nicole J; Tortora, Paolo

2012-07-27

We have detected in Cassini spacecraft data the signature of the periodic tidal stresses within Titan, driven by the eccentricity (e = 0.028) of its 16-day orbit around Saturn. Precise measurements of the acceleration of Cassini during six close flybys between 2006 and 2011 have revealed that Titan responds to the variable tidal field exerted by Saturn with periodic changes of its quadrupole gravity, at about 4% of the static value. Two independent determinations of the corresponding degree-2 Love number yield k(2) = 0.589 ± 0.150 and k(2) = 0.637 ± 0.224 (2σ). Such a large response to the tidal field requires that Titan's interior be deformable over time scales of the orbital period, in a way that is consistent with a global ocean at depth.

Titan through Time: Evolution of Titan's Atmosphere and its Hydrocarbon Cycle on the Surface

Science.gov (United States)

Gilliam, Ashley E.

The Introduction and Appendix i-A outline briefly the history of Titan exploration since its discovery by Christiaan Huygens in 1675 through the recent International Mission of Cassini-Huygens.. Chapter 1: This chapter discusses two possible pathways of loss of the two main gases from Titan's post-accretional atmosphere, methane (CH 4) and ammonia (NH3), by the mechanisms of thermal escape and emission from the interior coupled with thermal escape. Chapter 2: In this chapter, a simple photolysis model is created, where the second most abundant component of the present-day Titan atmosphere, methane (CH4), can either escape the atmosphere or undergo photolytic conversion to ethane (C2H6). Chapter 3: This chapter examines different fluvial features on Titan, identified by the Cassini spacecraft, and evaluates the possibilities of channel formation by two mechanisms: dissolution of ice by a concentrated solution of ammonium sulfate, and by mechanical erosion by flow of liquid ammonia and liquid ethane. Chapter 4: This chapter presents: (1) new explicit mathematical solutions of mixed 1st and 2nd order chemical reactions, represented by ordinary differential first-degree and Riccati equations; (2) the computed present-day concentrations of the three gases in Titan's scale atmosphere, treated as at near-steady state; and (3) an analysis of the reported and computed atmospheric concentrations of CH4, CH 3, and C2H6 on Titan, based on the reaction rate parameters of the species, the rate parameters taken as constants representative of their mean values. Chapter 5: This chapter examines the possible reactions of methane formation in terms of the thermodynamic relationships of the reactions that include pure carbon as graphite, the gases H2, CO2, H2 O, and serpentinization and magnetite formation from olivine fayalite. (Abstract shortened by ProQuest.).

Novel Pharmaceutical Strontium Malonate Influence on Calcium and Strontium Adsorption by Dog Femur and by Dog Teeth in a Four-Week Toxicity Study

DEFF Research Database (Denmark)

Raffalt, Anders Christer; Christgau, Stephan; Andersen, Jens Enevold Thaulov

of osteoporosis. As part of this development the compound was administered in doses of 0 (placebo), 300, 1000 and 3000 mg/kg/day to beagle dogs for a period of 4 weeks. We measured the incorporation of strontium in bone, marrow and teeth in this study. Analysis by inductively coupled plasma mass spectrometry...... marginally higher incorporation of strontium suggesting that saturation levels were reached with the lowest dose level. There was no gender difference in strontium incorporation. Correlations of strontium levels with Sr/Ca-ratio and other important biological parameters were investigated....

Titan LEAF: A Sky Rover Granting Targeted Access to Titan's Lakes and Plains

Science.gov (United States)

Ross, Floyd; Lee, Greg; Sokol, Daniel; Goldman, Benjamin; Bolisay, Linden

2016-10-01

Northrop Grumman, in collaboration with L'Garde Inc. and Global Aerospace Corporation (GAC), has been developing the Titan Lifting Entry Atmospheric Flight (T-LEAF) sky rover to roam the atmosphere and observe at close quarters the lakes and plains of Titan. T-LEAF also supports surface exploration and science by providing precision delivery of in situ instruments to the surface.T-LEAF is a maneuverable, buoyant air vehicle. Its aerodynamic shape provides its maneuverability, and its internal helium envelope reduces propulsion power requirements and also the risk of crashing. Because of these features, T-LEAF is not restricted to following prevailing wind patterns. This freedom of mobility allows it be commanded to follow the shorelines of Titan's methane lakes, for example, or to target very specific surface locations.T-LEAF utilizes a variable power propulsion system, from high power at ~200W to low power at ~50W. High power mode uses the propellers and control surfaces for additional mobility and maneuverability. It also allows the vehicle to hover over specific locations for long duration surface observations. Low power mode utilizes GAC's Titan Winged Aerobot (TWA) concept, currently being developed with NASA funding, which achieves guided flight without the use of propellers or control surfaces. Although slower than high powered flight, this mode grants increased power to science instruments while still maintaining control over direction of travel.Additionally, T-LEAF is its own entry vehicle, with its leading edges protected by flexible thermal protection system (f-TPS) materials already being tested by NASA's Hypersonic Inflatable Aerodynamic Decelerator (HIAD) group. This f-TPS technology allows T-LEAF to inflate in space, like HIAD, and then enter the atmosphere fully deployed. This approach accommodates entry velocities from as low as ~1.8 km/s if entering from Titan orbit, up to ~6 km/s if entering directly from Saturn orbit, like the Huygens probe

Characterizing the Upper Atmosphere of Titan using the Titan Global Ionosphere- Thermosphere Model: Nitrogen and Methane.

Science.gov (United States)

Bell, J. M.; Waite, J. H.; Bar-Nun, A.; Bougher, S. W.; Ridley, A. J.; Magee, B.

2008-12-01

Recently, a great deal of effort has been put forth to explain the Cassini Ion-Neutral Mass Spectrometer (Waite et al [2004]) in-situ measurements of Titan's upper atmosphere (e.g. Muller-Wodarg [2008], Strobel [2008], Yelle et al [2008]). Currently, the community seems to agree that large amounts of CH4 are escaping from Titan's upper atmosphere at a rate of roughly 2.0 x 1027 molecules of CH4/s (3.33 x 1028 amu/s), representing a significant mass source to the Kronian Magnetosphere. However, such large escape fluxes from Titan are currently not corroborated by measurements onboard the Cassini Spacecraft. Thus, we posit another potential scenario: Aerosol depletion of atmospheric methane. Using the three-dimensional Titan Global Ionosphere-Thermosphere Model (T-GITM) (Bell et al [2008]), we explore the possible removal mechanisms of atmospheric gaseous constituents by these aerosols. Titan simulations are directly compared against Cassini Ion-Neutral Mass Spectrometer in-situ densities of N2 and CH4. From this work, we can then compare and contrast this aerosol depletion scenario against the currently posited hydrodynamic escape scenario, illustrating the merits and shortcomings of both.

Diurnal variations of Titan's ionosphere

Science.gov (United States)

Cui, J.; Galand, M.; Yelle, R. V.; Vuitton, V.; Wahlund, J.-E.; Lavvas, P. P.; Müller-Wodarg, I. C. F.; Cravens, T. E.; Kasprzak, W. T.; Waite, J. H.

2009-06-01

We present our analysis of the diurnal variations of Titan's ionosphere (between 1000 and 1300 km) based on a sample of Ion Neutral Mass Spectrometer (INMS) measurements in the Open Source Ion (OSI) mode obtained from eight close encounters of the Cassini spacecraft with Titan. Although there is an overall ion depletion well beyond the terminator, the ion content on Titan's nightside is still appreciable, with a density plateau of ˜700 cm-3 below ˜1300 km. Such a plateau is a combined result of significant depletion of light ions and modest depletion of heavy ones on Titan's nightside. We propose that the distinctions between the diurnal variations of light and heavy ions are associated with their different chemical loss pathways, with the former primarily through “fast” ion-neutral chemistry and the latter through “slow” electron dissociative recombination. The strong correlation between the observed night-to-day ion density ratios and the associated ion lifetimes suggests a scenario in which the ions created on Titan's dayside may survive well to the nightside. The observed asymmetry between the dawn and dusk ion density profiles also supports such an interpretation. We construct a time-dependent ion chemistry model to investigate the effect of ion survival associated with solid body rotation alone as well as superrotating horizontal winds. For long-lived ions, the predicted diurnal variations have similar general characteristics to those observed. However, for short-lived ions, the model densities on the nightside are significantly lower than the observed values. This implies that electron precipitation from Saturn's magnetosphere may be an additional and important contributor to the densities of the short-lived ions observed on Titan's nightside.

High temperature superconducting material: Bismuth strontium calcium copper oxide. (Latest citations from the Aerospace database). Published Search

International Nuclear Information System (INIS)

1993-11-01

The bibliography contains citations concerning the development, fabrication, and analysis of a high temperature superconducting material based on bismuth-strontium-calcium-copper-oxides (Bi-Sr-Ca-Cu-O). Topics include the physical properties, structural and compositional analysis, magnetic field and pressure effects, and noble metal dopings of Bi-Sr-Ca-Cu-O based systems. The highest transition temperature recorded to date for this material was 120 degrees Kelvin. Fabrication methods and properties of Bi-Sr-Ca-Cu-O films and ceramics are also considered. (Contains 250 citations and includes a subject term index and title list.)

Effect of ‘A’-site non stoichiometry in strontium doped lanthanum ferrite based solid oxide fuel cell cathodes

Energy Technology Data Exchange (ETDEWEB)

Banerjee, Koyel; Mukhopadhyay, Jayanta, E-mail: jayanta_mu@cgcri.res.in; Barman, Madhurima; Basu, Rajendra N., E-mail: rnbasu@cgcri.res.in

2015-12-15

Highlights: • La{sub 1−x}Sr{sub x}Co{sub y}Fe{sub 1−y}O{sub 3−δ}, x = 0.4; y = 0.2 system varying La-site (0.6–0.54) are studied. • Combustion synthesis technique is used to prepare the powder samples. • Highest electrical conductivity observed with largest A-site deficit composition. • Lowest cathode polarization is found with the same composition (0.02 Ω cm{sup 2}). • Composition with largest A-site deficiency exhibits best performance (2.84 A cm{sup −2}). - Abstract: Effect of A-site non-stoichiometry in strontium doped lanthanum cobalt ferrite (La{sub 1−x}Sr{sub x}Co{sub y}Fe{sub 1−y}O{sub 3−δ}, x = 0.4; y = 0.2) is studied in a systematic manner with variation of ‘A’ site stoichiometry from 1 to 0.94. The perovskite based cathode compositions are synthesized by combustion synthesis. Powder characterizations reveal rhombohedral crystal structure with crystallite size ranging from 29 to 34 nm with minimum lattice spacing of 0.271 nm. Detailed sintering studies along with total DC electrical conductivities are evaluated in the bulk form with variation of sintering temperatures. The electrode polarizations are measured in the symmetric cell configuration by impedance spectroscopy which is found to be the lowest (0.02 Ω cm{sup 2} at 800 °C) for cathode having highest degree of ‘A’-site deficiency. The same cathode composition exhibits a current density of 2.84 A cm{sup −2} (at 0.7 V, 800 °C) in anode-supported single cell. An attempt has been made to correlate the trend of electrical behaviour with increasing ‘A’-site deficiency for such cathode compositions.

Investigation of strontium accumulation on ovariectomized Sprague–Dawley rat tibia by micro-PIXE

Energy Technology Data Exchange (ETDEWEB)

Li, X.; Li, Y. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Jin, W. [Institute of Radiation Medicine, Fudan University, Shanghai 200032 (China); Zheng, Y.; Rong, C.; Lyu, H. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Shen, H., E-mail: haoshen@fudan.edu.cn [Institute of Modern Physics, Fudan University, Shanghai 200433 (China)

2014-08-01

Strontium ranelate is a newly developed drug effective in osteoporosis treatment by depressing bone resorption and maintaining bone formation. Strontium accumulation and distribution are determined in bones of rat after strontium ranelate administration by using micro-PIXE. The investigated rats are divided into four groups: (A) control, (B) ovariectomized, (C) ovariectomized followed with strontium chloride, (D) ovariectomized followed with strontium ranelate. It was found that strontium ranelate would result in increasing trabecular volume and decreasing bone resorption to treat osteoporosis. There are similar contours of calcium and strontium in two-dimensional images, while the strontium is not evenly distributed in the bone. It supports the conclusion that strontium has an affinity for bone and it is capable of replacing calcium atoms as a part of the strontium mechanism in the osteoporosis treatment. The results related to biochemistry are also discussed.

Strontium-Doped Calcium Phosphate and Hydroxyapatite Granules Promote Different Inflammatory and Bone Remodelling Responses in Normal and Ovariectomised Rats

Science.gov (United States)

Xia, Wei; Emanuelsson, Lena; Norlindh, Birgitta; Omar, Omar; Thomsen, Peter

2013-01-01

The healing of bone defects may be hindered by systemic conditions such as osteoporosis. Calcium phosphates, with or without ion substitutions, may provide advantages for bone augmentation. However, the mechanism of bone formation with these materials is unclear. The aim of this study was to evaluate the healing process in bone defects implanted with hydroxyapatite (HA) or strontium-doped calcium phosphate (SCP) granules, in non-ovariectomised (non-OVX) and ovariectomised (OVX) rats. After 0 (baseline), six and 28d, bone samples were harvested for gene expression analysis, histology and histomorphometry. Tumour necrosis factor-α (TNF-α), at six days, was higher in the HA, in non-OVX and OVX, whereas interleukin-6 (IL-6), at six and 28d, was higher in SCP, but only in non-OVX. Both materials produced a similar expression of the receptor activator of nuclear factor kappa-B ligand (RANKL). Higher expression of osteoclastic markers, calcitonin receptor (CR) and cathepsin K (CatK), were detected in the HA group, irrespective of non-OVX or OVX. The overall bone formation was comparable between HA and SCP, but with topological differences. The bone area was higher in the defect centre of the HA group, mainly in the OVX, and in the defect periphery of the SCP group, in both non-OVX and OVX. It is concluded that HA and SCP granules result in comparable bone formation in trabecular bone defects. As judged by gene expression and histological analyses, the two materials induced different inflammatory and bone remodelling responses. The modulatory effects are associated with differences in the spatial distribution of the newly formed bone. PMID:24376855

Titan the earth-like moon

CERN Document Server

Coustenis, Athena

1999-01-01

This is the first book to deal with Titan, one of the most mysterious bodies in the solar system. The largest satellite of the giant planet Saturn, Titan is itself larger than the planet Mercury, and is unique in being the only known moon with a thick atmosphere. In addition, its atmosphere bears a startling resemblance to the Earth's, but is much colder.The American and European space agencies, NASA and ESA, have recently combined efforts to send a huge robot spacecraft to orbit Saturn and land on Titan. This book provides the background to this, the greatest deep space venture of our time, a

Titan and habitable planets around M-dwarfs.

Science.gov (United States)

Lunine, Jonathan I

2010-01-01

The Cassini-Huygens mission discovered an active "hydrologic cycle" on Saturn's giant moon Titan, in which methane takes the place of water. Shrouded by a dense nitrogen-methane atmosphere, Titan's surface is blanketed in the equatorial regions by dunes composed of solid organics, sculpted by wind and fluvial erosion, and dotted at the poles with lakes and seas of liquid methane and ethane. The underlying crust is almost certainly water ice, possibly in the form of gas hydrates (clathrate hydrates) dominated by methane as the included species. The processes that work the surface of Titan resemble in their overall balance no other moon in the solar system; instead, they are most like that of the Earth. The presence of methane in place of water, however, means that in any particular planetary system, a body like Titan will always be outside the orbit of an Earth-type planet. Around M-dwarfs, planets with a Titan-like climate will sit at 1 AU--a far more stable environment than the approximately 0.1 AU where Earth-like planets sit. However, an observable Titan-like exoplanet might have to be much larger than Titan itself to be observable, increasing the ratio of heat contributed to the surface atmosphere system from internal (geologic) processes versus photons from the parent star.

PEROXOTITANATE- AND MONOSODIUM METAL-TITANATE COMPOUNDS AS INHIBITORS OF BACTERIAL GROWTH

Energy Technology Data Exchange (ETDEWEB)

Hobbs, D.

2011-01-19

Sodium titanates are ion-exchange materials that effectively bind a variety of metal ions over a wide pH range. Sodium titanates alone have no known adverse biological effects but metal-exchanged titanates (or metal titanates) can deliver metal ions to mammalian cells to alter cell processes in vitro. In this work, we test a hypothesis that metal-titanate compounds inhibit bacterial growth; demonstration of this principle is one prerequisite to developing metal-based, titanate-delivered antibacterial agents. Focusing initially on oral diseases, we exposed five species of oral bacteria to titanates for 24 h, with or without loading of Au(III), Pd(II), Pt(II), and Pt(IV), and measuring bacterial growth in planktonic assays through increases in optical density. In each experiment, bacterial growth was compared with control cultures of titanates or bacteria alone. We observed no suppression of bacterial growth by the sodium titanates alone, but significant (p < 0.05, two-sided t-tests) suppression was observed with metal-titanate compounds, particularly Au(III)-titanates, but with other metal titanates as well. Growth inhibition ranged from 15 to 100% depending on the metal ion and bacterial species involved. Furthermore, in specific cases, the titanates inhibited bacterial growth 5- to 375-fold versus metal ions alone, suggesting that titanates enhanced metal-bacteria interactions. This work supports further development of metal titanates as a novel class of antibacterials.

Titan's geoid and hydrology: implications for Titan's geological evolution

Science.gov (United States)

Sotin, Christophe; Seignovert, Benoit; Lawrence, Kenneth; MacKenzie, Shannon; Barnes, Jason; Brown, Robert

2014-05-01

A 1x1 degree altitude map of Titan is constructed from the degree 4 gravity potential [1] and Titan's shape [2] determined by the Radio Science measurements and RADAR observations of the Cassini mission. The amplitude of the latitudinal altitude variations is equal to 300 m compared to 600 m for the amplitude of the latitudinal shape variations. The two polar caps form marked depressions with an abrupt change in topography at exactly 60 degrees at both caps. Three models are envisaged to explain the low altitude of the polar caps: (i) thinner ice crust due to higher heat flux at the poles, (ii) fossil shape acquired if Titan had higher spin rate in the past, and (iii) subsidence of the crust following the formation of a denser layer of clathrates as ethane rain reacts with the H2O ice crust [3]. The later model is favored because of the strong correlation between the location of the cloud system during the winter season and the latitude of the abrupt change in altitude. Low altitude polar caps would be the place where liquids would run to and eventually form large seas. Indeed, the large seas of Titan are found at the deepest locations at the North Pole. However, the lakes and terrains considered to be evaporite candidates due to their spectral characteristics in the infrared [4,5] seem to be perched. Lakes may have been filled during Titan's winter and then slowly evaporated leaving material on the surface. Interestingly, the largest evaporite deposits are located at the equator in a deep depression 150 m below the altitude of the northern seas. This observation seems to rule out the presence of a global subsurface hydrocarbon reservoir unless the evaporation rate at the equator is faster than the transport of fluids from the North Pole to the equator. This work has been performed at the Jet Propulsion Laboratory, California Institute of Technology, under contract to NASA. [1] Iess L. et al. (2012) Science, doi 10.1126/science.1219631. [2] Lorenz R.D. (2013

Effect of strontium ranelate on bone mineral: Analysis of nanoscale compositional changes.

Science.gov (United States)

Rossi, André L; Moldovan, Simona; Querido, William; Rossi, Alexandre; Werckmann, Jacques; Ersen, Ovidiu; Farina, Marcos

2014-01-01

Strontium ranelate has been used to prevent bone loss and stimulate bone regeneration. Although strontium may integrate into the bone crystal lattice, the chemical and structural modifications of the bone when strontium interacts with the mineral phase are not completely understood. The objective of this study was to evaluate apatite from the mandibles of rats treated with strontium ranelate in the drinking water and compare its characteristics with those from untreated rats and synthetic apatites with and without strontium. Electron energy loss near edge structures from phosphorus, carbon, calcium and strontium were obtained by electron energy loss spectroscopy in a transmission electron microscope. The strontium signal was detected in the biological and synthetic samples containing strontium. The relative quantification of carbon by analyzing the CK edge at an energy loss of ΔE = 284 eV showed an increase in the number of carbonate groups in the bone mineral of treated rats. A synthetic strontium-containing sample used as control did not exhibit a carbon signal. This study showed physicochemical modifications in the bone mineral at the nanoscale caused by the systemic administration of strontium ranelate. Copyright © 2013 Elsevier Ltd. All rights reserved.

A process for the development of strontium hydroxyapatite

International Nuclear Information System (INIS)

Zahra, N; Fayyaz, M; Iqbal, W; Irfan, M; Alam, S

2014-01-01

A procedure for the preparation of Strontium Hydroxyapatite is adapted to produce high purity and better homogeneity ceramic with good Crystallinity. The strontium substituted bone cement has potential for use in orthopedic surgeries. Ionic Strontium (Sr) in humans shares the same physiological pathway as calcium and can be deposited in the mineral structure of the bone. In the present study, a novel concept of preparing Sr-contained Hydroxyapatite bone cement by using a precipitation method is proposed to get an ideal biomaterial that possesses potential degradability and more excellent pharmacological effect. Chemical analysis, Fourier Transform Infra Red analysis and Thermogravimetric/ Differential Scanning Calorimetric studies were conducted on prepared Strontium Hydroxyapatite sample to characterize the incorporation of 15% Sr 2 + into the crystal lattice of Hydroxyapatite. Strontium was quantitatively incorporated into Hydroxyapatite where its substitution for calcium provoked a linear shift of the infrared absorption bands of the hydroxyl and phosphate groups. Thus, the formation of Sr-HAp was confirmed by Chemical Analysis, FT-IR and TGA/DSC results

A process for the development of strontium hydroxyapatite

Science.gov (United States)

Zahra, N.; Fayyaz, M.; Iqbal, W.; Irfan, M.; Alam, S.

2014-06-01

A procedure for the preparation of Strontium Hydroxyapatite is adapted to produce high purity and better homogeneity ceramic with good Crystallinity. The strontium substituted bone cement has potential for use in orthopedic surgeries. Ionic Strontium (Sr) in humans shares the same physiological pathway as calcium and can be deposited in the mineral structure of the bone. In the present study, a novel concept of preparing Sr-contained Hydroxyapatite bone cement by using a precipitation method is proposed to get an ideal biomaterial that possesses potential degradability and more excellent pharmacological effect. Chemical analysis, Fourier Transform Infra Red analysis and Thermogravimetric/ Differential Scanning Calorimetric studies were conducted on prepared Strontium Hydroxyapatite sample to characterize the incorporation of 15% Sr2+ into the crystal lattice of Hydroxyapatite. Strontium was quantitatively incorporated into Hydroxyapatite where its substitution for calcium provoked a linear shift of the infrared absorption bands of the hydroxyl and phosphate groups. Thus, the formation of Sr-HAp was confirmed by Chemical Analysis, FT-IR and TGA/DSC results.

Method for strontium isolation from high-mineralized water

International Nuclear Information System (INIS)

Evzhanov, Kh.; Andriyasova, G.M.

1983-01-01

A method to isolate strontium from high-mineralized waters containing sodium, magnesium, calcium and strontium chlorides, which differ from the prototype method in a considerable decrease in energy consumption with the preservation of a high degree of Sr, Mg and Ca isolation selectivity, has been suggested. According to the method suggested mineralized waters are treated with alkali (NaOH) in the amount of 95-97% of stoichiometry by magnesium, then after separation of magnesium hydroxide precipitate mother liquor is treated with sodium carbonate in the amount of 50-60% of stoichiometry by calcium. After separation of calcium carbonate precipitate mother liquor is treated with NaOH in the amount of 130-135% of stoichiometry by calcium. After separation of calcium hydroxide precipitate from mother liquor by means of sodium carbonate introduction strontium carbonate is isolated. The degree of strontium extraction in the form of SrCO 3 constitutes 90.5% of its content in the initial solution. The method presented can be used for strontium separation from natural and waste waters

A process for the development of strontium hydroxyapatite

International Nuclear Information System (INIS)

Zahra, N.; Fayyaz, M.; Iqbal, W.; Irfan, M.; Alam, S.

2013-01-01

A procedure for the preparation of Strontium Hydroxyapatite is adapted to produce high purity and better homogeneity ceramic with good Crystallinity. The strontium substituted bone cement has potential for use in orthopedic surgeries. Ionic Strontium (Sr) in humans shares the same physiological pathway as calcium and can be deposited in the mineral structure of the bone. In the present study, a novel concept of preparing Sr-contained Hydroxyapatite bone cement by using a precipitation method is proposed to get an ideal biomaterial that possesses potential degradability and more excellent pharmacological effect. Chemical analysis, Fourier Transform Infra Red analysis and Thermogravimetric/ Differential Scanning Calorimetric studies were conducted on prepared Strontium Hydroxyapatite sample to characterize the incorporation of 15 percentage Sr2+ into the crystal lattice of Hydroxyapatite. Strontium was quantitatively incorporated into Hydroxyapatite where its substitution for calcium provoked a linear shift of the infrared absorption bands of the hydroxyl and phosphate groups. Thus, the formation of Sr-HAp was confirmed by Chemical Analysis, FT-IR and TGA/DSC results. (author)

Nonthermal atmospheric escape from Mars and Titan

International Nuclear Information System (INIS)

Lammer, H.; Bauer, S.J.

1991-01-01

Energy flux spectra and particle concentrations of the hot O and N coronae from Mars and Titan, respectively, resulting primarily from dissociative recombination of molecular ions, have been calculated by means of a Monte Carlo method. The calculated energy flux spectra lead to an escape flux null esc ∼ 6 x 10 6 cm -2 s -1 for Mars and null esc ∼ 2 x 10 6 cm -2 s -1 for Titan, corresponding to a mass loss of about 0.14 kg/s for Mars and about 0.3 kg/s for Titan. (The contribution of electron impact ionization on N 2 amounts to only about 25% of Titan's mass loss.) Mass loss via solar and magnetospheric wind is also estimated using newly calculated mass loading limits. The mass loss via ion pickup from the extended hot atom corona for Mars amounts to about 0.25 kg/s (O + ) and for Titan to about 50 g/s (N 2 + or H 2 CN + ). Thus, the total mass loss rate from Mars and Titan is about the same, i.e., 0.4 kg/s

Separation of cesium and strontium with zeolites

Energy Technology Data Exchange (ETDEWEB)

Kanno, T; Hashimoto, H [Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy

1976-06-01

The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it.

Separation of cesium and strontium with zeolites

International Nuclear Information System (INIS)

Kanno, Takuji; Hashimoto, Hiroyuki

1976-01-01

The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it. (auth.)

Strontium 90 in silts of the Dnieper cascade water reservoirs

International Nuclear Information System (INIS)

Romanenko, V.D.; Kuz'menko, M.I.; Matvienko, L.P.; Klenus, V.G.; Nasvit, O.I.

1989-01-01

The change of strontium-90 content in water and silts of the Dnieper cascade water reservoirs was analyzed. It was shown, that decrease of strontium-90 content in water in time connected basically with ion exchange adsorption of strontium-90 by residues. A high sorption ability of residues made it possible for radioisotopes to reduce sharply their concentration along depth of soils. The highest concentration of radioisotopes was in the upper layers, enriched by silt. It was ascertained, that strontium-90 migration along depth of residues took place rapidly in the Kiev's water reservoir. Down the cascade strontium-90 content reduced in lower layers of residues as well as in upper layers. 4 tabs

A whiff of nebular gas in Titan's atmosphere - Potential implications for the conditions and timing of Titan's formation

Science.gov (United States)

Glein, Christopher R.

2017-09-01

In situ data from the GCMS instrument on the Huygens probe indicate that Titan's atmosphere contains small amounts of the primordial noble gases 36Ar and 22Ne (tentative detection), but it is unknown how they were obtained by the satellite. Based on the apparent similarity in the 22Ne/36Ar (atom) ratio between Titan's atmosphere and the solar composition, a previously neglected hypothesis for the origin of primordial noble gases in Titan's atmosphere is suggested - these species may have been acquired near the end of Titan's formation, when the moon could have gravitationally captured some nebular gas that would have been present in its formation environment (the Saturnian subnebula). These noble gases may be remnants of a primary atmosphere. This could be considered the simplest hypothesis to explain the 22Ne/36Ar ratio observed at Titan. However, the 22Ne/36Ar ratio may not be exactly solar if these species can be fractionated by external photoevaporation in the solar nebula, atmospheric escape from Titan, or sequestration on the surface of Titan. While the GCMS data are consistent with a 22Ne/36Ar ratio of 0.05 to 2.5 times solar (1σ range), simple estimates that attempt to account for some of the effects of these evolutionary processes suggest a sub-solar ratio, which may be depleted by approximately one order of magnitude. Models based on capture of nebular gas can explain why the GCMS did not detect any other primordial noble gas isotopes, as their predicted abundances are below the detection limits (especially for 84Kr and 132Xe). It is also predicted that atmospheric Xe on Titan should be dominated by radiogenic 129Xe if the source of primordial Xe is nebular gas. Of order 10-2-10-1 bar of primordial H2 may have been captured along with the noble gases from a gas-starved disk, but this H2 would have quickly escaped from the initial atmosphere. To have the opportunity to capture nebular gas, Titan should have formed within ∼10 Myr of the formation of the

Coupled atmosphere-ocean models of Titan's past

Science.gov (United States)

Mckay, Christopher P.; Pollack, James B.; Lunine, Jonathan I.; Courtin, Regis

1993-01-01

The behavior and possible past evolution of fully coupled atmosphere and ocean model of Titan are investigated. It is found that Titan's surface temperature was about 20 K cooler at 4 Gyr ago and will be about 5 K warmer 0.5 Gyr in the future. The change in solar luminosity and the conversion of oceanic CH4 to C2H6 drive the evolution of the ocean and atmosphere over time. Titan appears to have experienced a frozen epoch about 3 Gyr ago independent of whether an ocean is present or not. This finding may have important implications for understanding the inventory of Titan's volatile compounds.

Surface modification of strontium-doped porous bioactive ceramic scaffolds via poly(DOPA) coating and immobilizing silk fibroin for excellent angiogenic and osteogenic properties.

Science.gov (United States)

Wang, Xu; Gu, Zhipeng; Jiang, Bo; Li, Li; Yu, Xixun

2016-04-01

For bioceramic scaffolds employed in clinical applications, excellent bioactivity and tenacity were of great importance. Modifying inorganic SCPP scaffolds with biological macromolecules could obviously improve its bioactivity and eliminate its palpable brittleness. However, it was hard to execute directly due to extremely bad interfacial compatibility between them. In this research, dopamine (DOPA) was introduced onto strontium-doped calcium polyphosphate (SCPP) scaffolds, subsequently the preliminary material was successfully further modified by silk fibroin (SF). SCPP/D/SF possessed suitable biomechanical properties, ability to stimulate angiogenic factor secretion and excellent biocompatibility. Biomechanical examination demonstrated that SCPP/D/SF scaffolds yielded better compressive strength because of improved interfacial compatibility. MTT assay and CLSM observation showed that SCPP/D/SF scaffolds had good cytocompatibility and presented better inducing-cell-migration potential than pure SCPP scaffolds. Meanwhile, its ability to stimulate angiogenic factor secretion was measured through the ELISA assay and immunohistological analysis in vitro and in vivo respectively. The results revealed, superior to SCPP, SCPP/D/SF could effectively promote VEGF and bFGF expression, possibly leading to enhancing angiogenesis and osteogenesis. In a word, SCPP/D/SF could serve as a potential bone tissue engineering scaffold for comparable biomechanical properties and excellent bioactivity. It provided a novel idea for modification of inorganic materials to prepare promising bone tissue engineering scaffolds with the ability to accelerate bone regeneration and vascularization.

A study on characteristic of selective membrane for strontium analysis

Energy Technology Data Exchange (ETDEWEB)

Moon, Seung Hyun; Choi, Young Woo [Kwang-ju Institute of Science and Technology, Kwangju (Korea)

1999-04-01

In this study, supported liquid membranes (SLMs) using crown ether were prepared in order to separate strontium ion selectively from a calcium contained solution However, at the higher than 3 N nitric acid concentration of a strip solution, stability of a SLM was declined remarkably owing to the hasty loss of carrier impregnated in supporter and, on account of this phenomena, facilitated transports were not accomplished. And DC18C6 as a neutral carrier affected remarkably the selectivity of strontium and the factor determining permeabilities of metal ions was as a role of DNNS. Consequently, in order to be a optimal SLM for the high permeability and the stable selectivity of strontium, concentration of DC18C6 and DNNS should be 0.1 M and 25 mM, respectively and, at this condition, the relative removal ratio of strontium to calcium was 93.3%. And the change of calcium concentration in the feed solution affected the permeability of strontium. In particular, when the ratio of strontium to calcium concentration in the feed solution was in the range of 1/5 - 1/50, strontium could be separated selectively at stable permeabilities. (author). 17 refs., 19 figs., 3 tabs.

Strontium isotopic stratigraphy utilizing authigenic dolomites in hemipelagic sediments

Energy Technology Data Exchange (ETDEWEB)

Baker, P.A. (Duke Univ., Durham, NC (USA)); Kastner, M. (Scripps Institute of Oceanography, La Jolla, CA (USA)); Elderfield, H. (Univ. of Cambridge (England))

1990-05-01

Authigenic dolomites commonly occur in organic-rich, continental margin marine sediments. These dolomites play a key role in the age dating of stratigraphic sections. The dolomites often are the only lithology amenable to paleomagnetic stratigraphy; they preserve siliceous microfossils against diagenetic; recrystallization, and provide useful strontium isotopic stratigraphic ages. Several potential sources of error frequently are unique to the use of authigenic dolomites in the strontium isotope methods. (1) The dolomites occur as cements of the host lithology, hence, they are not a pure phase. Potentially important contaminants during analysis include gypsum clay minerals, feldspars, and iron and manganese oxides. Strontium may occur as a structural substituent ion in these minerals or as a surface-adsorbed ion. Various leaching techniques have been tested to isolate dolomitic strontium. Purer dolomites and strontium-enriched dolomites often can be selected to ease these problems. (2) The dolomites form after the deposition of the host sediment, therefore, they record the diagenetic age not the depositional age. The stable isotopic composition of the dolomites can aid in selection of early formed samples. (3) The dolomites record pore-water strontium isotope compositions, not seawater isotopic compositions. This problem is also minimized by choosing dolomites formed near the sediment-water interface. (4) The dolomites formed near the sediment-water interface originated as rotodolomites and undergo subsequent burial diagenesis, creating a potential for later strontium isotope exchange. This problem is minimized by selecting fresh samples from the interior of nearly impermeable beds and nodules. Results from the Miocene Monterey Formation of California and from the Eocene through Pliocene Pisco basin of Peru show that authigenic dolomites can provide useful strontium isotopic age estimates.

Titan atmospheric composition by hypervelocity shock layer analysis

International Nuclear Information System (INIS)

Nelson, H.F.; Park, C.; Whiting, E.E.

1989-01-01

The Cassini Mission, a NASA/ESA cooperative project which includes a deployment of probe into the atmosphere of Titan, is described, with particular attention given to the shock radiometer experiment planned for the Titan probe for the analysis of Titan's atmosphere. Results from a shock layer analysis are presented, demonstrating that the mole fractions of the major species (N2, CH4, and, possibly Ar) in the Titan atmosphere can be successfully determined by the Titan-probe radiometer, by measuring the intensity of the CN(violet) radiation emitted in the shock layer during the high velocity portion of the probe entry between 200 and 400 km altitude. It is shown that the sensitivity of the CN(violet) radiation makes it possible to determine the mole fractions of N2, CH4, and Ar to about 0.015, 0.003, and 0.01, respectively, i.e., much better than the present uncertainties in the composition of Titan atmosphere. 29 refs

Strontium-90 (90Sr) determination using liquid scintillation counting

International Nuclear Information System (INIS)

Cheberle, L.T.V.; Rosa, M.M.L.; Ferreira, M.T.; Taddei, M.H.T.

2015-01-01

This procedure describes a method for separation and measurement of strontium 90 Sr in water, soils, and biological samples. Water samples may be concentrated using evaporation or calcium phosphate coprecipitation. Soils and biological materials must be dissolved using wet digestion. Tracers and carriers must be added before the attack. Radioactive strontium is separated employing a specific resin before determination by liquid scintillation counting using the double energetic window method. The resin is used to concentrate strontium from samples. Stable strontium is used to monitor method yields and correct results to improve precision and accuracy. The presence of elemental strontium in the sample may bias the gravimetric yield determination. If it is suspected that natural strontium is present in the sample, its concentration should be determined by a suitable means (ICP), and the yield calculation properly modified. Sr-Spec resin with an 8M HNO 3 load solution is used to effectively remove 140 Ba and 40 K isotopes, as well as other interferences from the matrix. Tetravalent plutonium, neptunium, cerium and ruthenium, however, are not removed using nitric acid. The radiochemical procedure was tested using PROCORAD intercomparison exercises and PNI samples. (author)

The Strontium Isotope Record of Zavkhan Terrane Carbonates: Strontium Isotope Stability Through the Ediacaran-Cambrian Transition

OpenAIRE

Petach, Tanya N.

2015-01-01

First order trends in the strontium isotopic (87Sr/86Sr) composition of seawater are controlled by radiogenic inputs from the continent and non-radiogenic inputs from exchange at mid-ocean ridges. Carbonates precipitated in seawater preserve trace amounts of strontium that record this isotope ratio and therefore record the relative importance of mid-ocean ridge and weathering chemical inputs to sea water composition. It has been proposed that environmental changes during the Ediacaran-Cambria...

Analyzing the defect structure of CuO-doped PZT and KNN piezoelectrics from electron paramagnetic resonance.

Science.gov (United States)

Jakes, Peter; Kungl, Hans; Schierholz, Roland; Eichel, Rüdiger-A

2014-09-01

The defect structure for copper-doped sodium potassium niobate (KNN) ferroelectrics has been analyzed with respect to its defect structure. In particular, the interplay between the mutually compensating dimeric (Cu(Nb)'''-V(O)··) and trimeric (V(O)··-Cu(Nb)'''-V(O)··)· defect complexes with 180° and non-180° domain walls has been analyzed and compared to the effects from (Cu'' - V(O)··)(x)× dipoles in CuO-doped lead zirconate titanate (PZT). Attempts are made to relate the rearrangement of defect complexes to macroscopic electromechanical properties.

Seawater strontium isotopes, acid rain, and the Cretaceous-Tertiary boundary

Science.gov (United States)

Macdougall, J. D.

1988-01-01

A large bolide impact at the end of the Cretaceous would have produced significant amounts of nitrogen oxides by shock heating of the atmosphere. The resulting acid precipitation would have increased continental weathering greatly and could be an explanation for the observed high ratio of strontium-87 to strontium-86 in seawater at about this time, due to the dissolution of large amounts of strontium from the continental crust. Spikes to high values in the seawater strontium isotope record at other times may reflect similar episodes.

Structural, magnetic and microwave absorption behavior of Co-Zr substituted strontium hexaferrites prepared using tartaric acid fuel for electromagnetic interference suppression

Energy Technology Data Exchange (ETDEWEB)

Kaur, Prabhjyot, E-mail: prabhjyot.2525@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar 143005 (India); Chawla, S.K., E-mail: sschawla118@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar 143005 (India); Narang, Sukhleen Bindra, E-mail: sukhleen2@yahoo.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar 143005 (India); Pubby, Kunal, E-mail: kunalpubby02@gmail.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar 143005 (India)

2017-01-15

Strontium hexaferrites, doped with varying Co-Zr content (x) have been synthesized by sol-gel auto-combustion route using tartaric acid as fuel at 800 °C. X-ray diffraction and Fourier transform Infra-red have been carried out to confirm the phase formation, particle size (average 21.9–36.8 nm) and the bond formation respectively. Magnetic properties are scrutinized using vibrating sample magnetometer. Techniques like scanning electron microscopy, transmission electron microscopy and energy dispersive scattering have been employed to explore the surface morphology, particle size and composition of the nano-powders. Electromagnetic characterization of the prepared ferrites has been done using Vector Network Anlyzer in 12.4–18 GHz frequency range. The effect of calcination temperature (500–1000 °C) on the structure, morphology and magnetic properties has also been studied for x=0.2 and 800 °C has been found to be the most suitable temperature with the best magnetic properties. Increase in doping has resulted in resonance peaks in dielectric and magnetic loss spectra, leading to microwave absorption peaks. Ferrites with x=0.2, 0.8 and 1.0 have appropriate reflection loss less than −10 dB and bandwidth in Ku-band, hence can be used as effective absorbers in suppression of electromagnetic interference (EMI). The governance of impedance matching in deciding the absorption properties has been proved by using input impedance calculations. - Highlights: • Co-Zr doped strontium hexaferrite nanopowders have been prepared by sol-gel route. • 800 °C was most suitable temperaturewith best structural and magnetic properties. • Samples have M-type hexagonal structure with an average particle size of 36.47 nm. • Samples x=0.2, 0.8 and 1.0 are suitable for suppression of EM waves in Ku-band. • The origin of absorption peaks: impedance matching and losses has been explained.

Strontium ranelate for preventing and treating postmenopausal osteoporosis.

Science.gov (United States)

O'Donnell, S; Cranney, A; Wells, G A; Adachi, J D; Reginster, J Y

2006-10-18

Strontium ranelate is a new treatment for osteoporosis therefore, its benefits and harms need to be known. To determine the efficacy and safety of strontium ranelate for the treatment and prevention of postmenopausal osteoporosis. We searched MEDLINE (1996 to March 2005), EMBASE (1996 to week 9 2005), the Cochrane Library (1996 to Issue 1 2005), reference lists of relevant articles and conference proceedings from the last two years. Additional data was sought from authors. We included randomized controlled trials (RCTs) of at least one year duration comparing strontium ranelate versus placebo reporting fracture incidence, bone mineral density (BMD), health related quality of life or safety in postmenopausal women. Treatment (versus prevention) population was defined as women with prevalent vertebral fractures and/or lumbar spine BMD T score gastritis or death. Additional data suggests that the risk of vascular and nervous system side-effects is slightly increased with taking 2 g of strontium ranelate daily over three to four years. There is silver level evidence (www.cochranemsk.org) to support the efficacy of strontium ranelate for the reduction of fractures (vertebral and to a lesser extent non-vertebral) in postmenopausal osteoporotic women and an increase in BMD in postmenopausal women with/without osteoporosis. Diarrhea may occur however, adverse events leading to study withdrawal were not significantly increased with taking 2 g of strontium ranelate daily. Potential vascular and neurological side-effects need to be further explored.

Characterization of Lanthanum Ferric Cobaltite doped with Strontium (LSCF) films deposited by spray-pyrolysis for application as cathode in PaCOS-TI; Caracterizacao de filmes de CFLE depositados por spray-pirolise para utilizacao como catodo em PaCOS-TI

Energy Technology Data Exchange (ETDEWEB)

Almeida, L.S.; Guimaraes, V.F.; Paes Junior, H.R. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (UENF), Campos dos Goytacazes, RJ (Brazil). Lab. de Materiais Avancados], Emails: laryssadsa@yahoo.com.br, valtencyguimaraes@yahoo.com.br, herval@uenf.br

2010-07-01

The lanthanum ferric cobaltite doped with strontium (LSCF) is a ceramic material with the perovskite structure that stands out in the field of research for its use as cathode in solid oxide fuel cells at intermediate temperatures (IT-SOFC). The films were synthesized by spray-pyrolysis technique on 8% mol Yttria stabilized zirconia (YSZ) substrates. It was studied the influence of heat treatment temperatures (600-1000 deg C) on the properties of the films under the conditions of treatment during four hours. Samples were tested electrically by measuring the variation of electrical conductivity with temperature, structurally by X-ray diffraction (XRD) and morphologically by scanning electron microscopy (SEM). The films heat treated at 700 deg C for 4 hours showed better performance for application as cathode. (author)

Morphology and structure of Ti-doped diamond films prepared by microwave plasma chemical vapor deposition

Science.gov (United States)

Liu, Xuejie; Lu, Pengfei; Wang, Hongchao; Ren, Yuan; Tan, Xin; Sun, Shiyang; Jia, Huiling

2018-06-01

Ti-doped diamond films were deposited through a microwave plasma chemical vapor deposition (MPCVD) system for the first time. The effects of the addition of Ti on the morphology, microstructure and quality of diamond films were systematically investigated. Secondary ion mass spectrometry results show that Ti can be added to diamond films through the MPCVD system using tetra n-butyl titanate as precursor. The spectra from X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy and the images from scanning electron microscopy of the deposited films indicate that the diamond phase clearly exists and dominates in Ti-doped diamond films. The amount of Ti added obviously influences film morphology and the preferred orientation of the crystals. Ti doping is beneficial to the second nucleation and the growth of the (1 1 0) faceted grains.

Lead titanate nanotubes synthesized via ion-exchange method: Characteristics and formation mechanism

International Nuclear Information System (INIS)

Song Liang; Cao Lixin; Li Jingyu; Liu Wei; Zhang Fen; Zhu Lin; Su Ge

2011-01-01

Highlights: → Lead titanate nanotubes PbTi 3 O 7 were firstly synthesized by ion-exchange method. → Sodium titanate nanotubes have ion exchangeability. → Lead titanate nanotubes show a distinct red shift on absorption edge. - Abstract: A two-step method is presented for the synthesis of one dimensional lead titanate (PbTi 3 O 7 ) nanotubes. Firstly, titanate nanotubes were prepared by an alkaline hydrothermal process with TiO 2 nanopowder as precursor, and then lead titanate nanotubes were formed through an ion-exchange reaction. We found that sodium titanate nanotubes have ion exchangeability with lead ions, while protonated titanate nanotubes have not. For the first time, we distinguished the difference between sodium titanate nanotubes and protonated titanate nanotubes in the ion-exchange process, which reveals a layer space effect of nanotubes in the ion-exchange reaction. In comparison with sodium titanate, the synthesized lead titanate nanotubes show a narrowed bandgap.

Titan's methane clock

Science.gov (United States)

Nixon, C. A.; Jennings, D. E.; Romani, P. N.; Teanby, N. A.; Irwin, P. G. J.; Flasar, F. M.

2010-04-01

Measurements of the 12C/13C and D/H isotopic ratios in Titan's methane show intriguing differences from the values recorded in the giant planets. This implies that either (1) the atmosphere was differently endowed with material at the time of formation, or (2) evolutionary processes are at work in the moon's atmosphere - or some combination of the two. The Huygens Gas Chromatograph Mass Spectrometer Instrument (GCMS) found 12CH4/13CH4 = 82 +/- 1 (Niemann et al. 2005), some 7% lower than the giant planets' value of 88 +/- 7 (Sada et al. 1996), which closely matches the terrestrial inorganic standard of 89. The Cassini Composite Infrared Spectrometer (CIRS) has previously reported 12CH4/13CH4 of 77 +/-3 based on nadir sounding, which we now revise upwards to 80 +/- 4 based on more accurate limb sounding. The CIRS and GCMS results are therefore in agreement about an overall enrichment in 13CH4 of ~10%. The value of D/H in Titan's CH4 has long been controversial: historical measurements have ranged from about 8-15 x 10-5 (e.g. Coustenis et al. 1989, Coustenis et al. 2003). A recent measurement based on CIRS limb data by Bezard et al. (2007) puts the D/H in CH4 at (13 +/- 1) x 10-5, very much greater than in Jupiter and Saturn, ~2 x 10-5 (Mahaffy et al. 1998, Fletcher et al. 2009). To add complexity, the 12C/13C and D/H vary among molecules in Titan atmosphere, typically showing enhancement in D but depletion in 13C in the daughter species (H2, C2H2, C2H6), relative to the photochemical progenitor, methane. Jennings et al. (2009) have sought to interpret the variance in carbon isotopes as a Kinetic Isotope Effect (KIE), whilst an explanation for the D/H in all molecules remains elusive (Cordier et al. 2008). In this presentation we argue that evolution of isotopic ratios in Titan's methane over time forms a ticking 'clock', somewhat analogous to isotopic ratios in geochronology. Under plausible assumptions about the initial values and subsequent replenishment, various

Controlling interface characteristics by adjusting core-shell structure

International Nuclear Information System (INIS)

Chang, H.Y.; Cheng, S.Y.; Sheu, C.I.

2004-01-01

Most grain boundary layer ceramics comprise semiconductive/conductive grains and insulated grain boundaries. Such a structure can be theoretically regarded as a shell (grain boundary layer) surrounds a core (conductive or semiconductive grain). The core-shell structure of titanium (Ti)-strontium titanate (ST) is composed of three zones - ST, non-stoichiometric strontium-titanium oxide and Ti, in order from shell to core. It was successfully prepared using a hydrothermal method. The Ti-ST core-shell structure was sintered in a reducing atmosphere and then annealed in air to achieve the metal-insulator-metal structure (MIM structure). The resulting MIM structure, annealed in air, changes with the oxygen stoichiometry of the ST shell (insulator layer) at various temperatures, which is thus used to tune its electrical characteristics. The characteristics exhibit nonlinear behavior. Accordingly, the thickness of the insulator layer can be adjusted in various annealing atmospheres and at various temperatures to develop various interfacial devices, such as varistors, capacitors and thermistors, without the use of complex donor/acceptor doping technology

Optical properties of Eu(III) doped strontium gadolinium niobate oxide

Energy Technology Data Exchange (ETDEWEB)

Vishwnath, Verma, E-mail: mnsmsu@gmail.com, E-mail: vermavicky.1988@gmail.com; Srinivas, M.; Patel, Nimesh; Modi, Dhaval [Luminescent Materials Laboratory, Physics Department, Faculty of Science, The M. S. University of Baroda, Vadodara-390002 (India); Murthy, K. V. R. [Display Materials Laboratory, Applied Physics Department, Faculty of Technology and Engineering, The M. S. University of Baroda, Vadodara-390001, Gujarat (India)

2016-05-23

Sr{sub 2}GdNbO{sub 6} doped with trivalent ion of Eu phosphors having monoclinic phase of space group P2{sub 1}/n have been synthesized via solid state reaction method, and their photoluminescence properties have been examined under UV excitation. The emission peaks exhibited around 580, 596, and 610 nm wavelength. By using xenon lamp as a source of excitation having wavelengths at 254 and 262 nm, it is observed that the maximum light emission yielded in red region. It is inferred that the dopant Eu{sup +3} ions may take the substitutional positions at non-centrosymmetric site.

Strontium-90 at the Hanford Site and its ecological implications

International Nuclear Information System (INIS)

RE Peterson; TM Poston

2000-01-01

Strontium-90, a radioactive contaminant from historical operations at the U.S. Department of Energy (DOE) Hanford Site, enters the Columbia River at several locations associated with former plutonium production reactors at the Site. Strontium-90 is of concern to humans and the environment because of its moderately long half-life (29.1 years), its potential for concentrating in bone tissue, and its relatively high energy of beta decay. Although strontium-90 in the environment is not a new issue for the Hanford Site, recent studies of near-river vegetation along the shoreline near the 100 Areas raised public concern about the possibility of strontium-90-contaminated groundwater reaching the riverbed and fall chinook salmon redds. To address these concerns, DOE asked Pacific Northwest National Laboratory (PNNL) to prepare this report on strontium-90, its distribution in groundwater, how and where it enters the river, and its potential ecological impacts, particularly with respect to fall chinook salmon. The purpose of the report is to characterize groundwater contaminants in the near-shore environment and to assess the potential for ecological impact using salmon embryos, one of the most sensitive ecological indicators for aquatic organisms. Section 2.0 of the report provides background information on strontium-90 at the Hanford Site related to historical operations. Public access to information on strontium-90 also is described. Section 3.0 focuses on key issues associated with strontium-90 contamination in groundwater that discharges in the Hanford Reach. The occurrence and distribution of fall chinook salmon redds in the Hanford Reach and characteristics of salmon spawning are described in Section 4.0. Section 5.0 describes the regulatory standards and criteria used to set action levels for strontium-90. Recommendations for initiating additional monitoring and remedial action associated with strontium-90 contamination at the Hanford Site are presented in Section 6

Strontium-90 at the Hanford Site and its ecological implications

Energy Technology Data Exchange (ETDEWEB)

RE Peterson; TM Poston

2000-05-22

Strontium-90, a radioactive contaminant from historical operations at the U.S. Department of Energy (DOE) Hanford Site, enters the Columbia River at several locations associated with former plutonium production reactors at the Site. Strontium-90 is of concern to humans and the environment because of its moderately long half-life (29.1 years), its potential for concentrating in bone tissue, and its relatively high energy of beta decay. Although strontium-90 in the environment is not a new issue for the Hanford Site, recent studies of near-river vegetation along the shoreline near the 100 Areas raised public concern about the possibility of strontium-90-contaminated groundwater reaching the riverbed and fall chinook salmon redds. To address these concerns, DOE asked Pacific Northwest National Laboratory (PNNL) to prepare this report on strontium-90, its distribution in groundwater, how and where it enters the river, and its potential ecological impacts, particularly with respect to fall chinook salmon. The purpose of the report is to characterize groundwater contaminants in the near-shore environment and to assess the potential for ecological impact using salmon embryos, one of the most sensitive ecological indicators for aquatic organisms. Section 2.0 of the report provides background information on strontium-90 at the Hanford Site related to historical operations. Public access to information on strontium-90 also is described. Section 3.0 focuses on key issues associated with strontium-90 contamination in groundwater that discharges in the Hanford Reach. The occurrence and distribution of fall chinook salmon redds in the Hanford Reach and characteristics of salmon spawning are described in Section 4.0. Section 5.0 describes the regulatory standards and criteria used to set action levels for strontium-90. Recommendations for initiating additional monitoring and remedial action associated with strontium-90 contamination at the Hanford Site are presented in Section 6

Strontium 90 in Swedish dairy milk 1978

International Nuclear Information System (INIS)

Gillberg-Wickman, M.; Oestergren, I.

1980-01-01

The contamination of strontium-90 in Swedish milk during 1978 is practically the same as in 1977. The country-wide mean ratio of strontium-90 to calcium in milk is 0.12 Bq 90 Sr(gCa) -1 , based on monthly determinations of samples obtained from 8 dairy plants situated throughout the country. (author)

Cesium and Strontium Separation Technologies Literature Review

Energy Technology Data Exchange (ETDEWEB)

T. A. Todd; T. A. Todd; J. D. Law; R. S. Herbst

2004-03-01

Integral to the Advanced Fuel Cycle Initiative (AFCI) Program’s proposed closed nuclear fuel cycle, the fission products cesium and strontium in the dissolved spent nuclear fuel stream are to be separated and managed separately. A comprehensive literature survey is presented to identify cesium and strontium separation technologies that have the highest potential and to focus research and development efforts on these technologies. Removal of these high-heat-emitting fission products reduces the radiation fields in subsequent fuel cycle reprocessing streams and provides a significant short-term (100 yr) heat source reduction in the repository. This, along with separation of actinides, may provide a substantial future improvement in the amount of fuel that could be stored in a geologic repository. The survey and review of the candidate cesium and strontium separation technologies are presented herein. Because the AFCI program intends to manage cesium and strontium together, technologies that simultaneously separate both elements are of the greatest interest, relative to technologies that separate only one of the two elements.

Titan Orbiter Aerorover Mission with Enceladus Science (TOAMES)

Science.gov (United States)

Sittler, E.; Cooper, J.; Mahaffy, P.; Fairbrother, D.; de Pater, I.; Schulze-Makuch, D.; Pitman, J.

2007-08-01

same time made us aware of how little we understand about these bodies. For example, the source, and/or recycling mechanism, of methane in Titan's atmosphere is still puzzling. Indeed, river beds (mostly dry) and lakes have been spotted, and occasional clouds have been seen, but the physics to explain the observations is still mostly lacking, since our "image" of Titan is still sketchy and quite incomplete. Enceladus, only 500 km in extent, is even more puzzling, with its fiery plumes of vapor, dust and ice emanating from its south polar region, "feeding" Saturn's E ring. Long term variability of magnetospheric plasma, neutral gas, E-ring ice grain density, radio emissions, and corotation of Saturn's planetary magnetic field in response to Enceladus plume activity are of great interest for Saturn system science. Both Titan and Enceladus are bodies of considerable astrobiological interest in view of high organic abundances at Titan and potential subsurface liquid water at Enceladus. We propose to develop a new mission to Titan and Enceladus, the Titan Orbiter Aerorover Mission with Enceladus Science (TOAMES), to address these questions using novel new technologies. TOAMES is a multi-faceted mission that starts with orbit insertion around Saturn using aerobraking with Titan's extended atmosphere. We then have an orbital tour around Saturn (for 1-2 years) and close encounters with Enceladus, before it goes into orbit around Titan (via aerocapture). During the early reconnaissance phase around Titan, perhaps 6 months long, the orbiter will use altimetry, radio science and remote sensing instruments to measure Titan's global topography, subsurface structure and atmospheric winds. This information will be used to determine where and when to release the Aerorover, so that it can navigate safely around Titan and identify prime sites for surface sampling and analysis. In situ instruments will sample the upper atmosphere which may provide the seed population for the complex

Spacecraft Exploration of Titan and Enceladus

Science.gov (United States)

Matson, D.; Coustenis, A.; Lunine, J. I.; Lebreton, J.; Reh, K.; Beauchamp, P.; Erd, C.

2009-12-01

The future exploration of Titan and Enceladus is very important for planetary science. The study titled Titan Saturn System Mission (TSSM) led to an announcement in which ESA and NASA prioritized future OPF missions, stating that TSSM is planned after EJSM (for details see http://www.lpi.usra.edu/opag/). The TSSM concept consists of an Orbiter that would carry two in situ elements: the Titan Montgolfiere hot air balloon and the Titan Lake Lander. This mission could launch in the 2023-2025 timeframe on a trajectory to arrive ~9 years later and begin a 4-year mission in the Saturnian system. At an appropriate time after arrival at Saturn, the montgolfiere would be delivered to Titan to begin its mission of airborne, scientific observations of Titan from an altitude of about 10 km above the surface. The montgolfiere would have a Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) power system whose waste heat would warm the gas in the balloon, providing buoyancy. It would be designed to survive at least 6-12 months in Titan’s atmosphere. With the predicted winds and weather, it should be possible to circumnavigate the globe! Later, on a subsequent fly-by, the TSSM orbiter would send the Lake Lander to Titan. It would descend through the atmosphere making scientific measurements, much like Huygens did, and then land and float on one of Titan’s seas. This would be its oceanographic phase of making a physical and chemical assessment of the sea. The Lake Lander would operate for 8-10 hours until its batteries become depleted. Following the delivery of the in situ elements, the TSSM orbiter would then explore the Saturn system for two years on a tour that includes in situ sampling of Enceladus’ plumes as well as flybys of Titan. After the Saturn tour, the TSSM orbiter would go into orbit around Titan and carry out a global survey phase. Synergistic observations would be carried out by the TSSM orbiter and the in situ elements. The scientific requirements for

Bactericidal strontium-releasing injectable bone cements based on bioactive glasses.

Science.gov (United States)

Brauer, Delia S; Karpukhina, Natalia; Kedia, Gopal; Bhat, Aditya; Law, Robert V; Radecka, Izabela; Hill, Robert G

2013-01-06

Strontium-releasing injectable bone cements may have the potential to prevent implant-related infections through the bactericidal action of strontium, while enhancing bone formation in patients suffering from osteoporosis. A melt-derived bioactive glass (BG) series (SiO2–CaO–CaF2–MgO) with 0–50% of calcium substituted with strontium on a molar base were produced. By mixing glass powder, poly(acrylic acid) and water, cements were obtained which can be delivered by injection and set in situ, giving compressive strength of up to 35 MPa. Strontium release was dependent on BG composition with increasing strontium substitution resulting in higher concentrations in the medium. Bactericidal effects were tested on Staphylococcus aureus and Streptococcus faecalis; cell counts were reduced by up to three orders of magnitude over 6 days. Results show that bactericidal action can be increased through BG strontium substitution, allowing for the design of novel antimicrobial and bone enhancing cements for use in vertebroplasty or kyphoplasty for treating osteoporosis-related vertebral compression fractures.

Analysis of radioactive strontium

International Nuclear Information System (INIS)

1977-01-01

In environmental radiation survey, radioactive strontium has been analyzed in compliance with the manual ''Analyzing methods for radioactive strontium'' published in 1960 by the Science and Technology Agency, Japan, and revised in 1963. However, in a past decade, progress and development in analyzing methods and measuring equipments have been significant, therefore the manual was revised in 1974. Major revisions are as follows. (1) Analysis of 90 Sr with long half life was changed to the main theme and that of 89 Sr with short half life became a subordinate one. (2) Measuring criteria and sampling volume were revised. (3) Sample collection method was unified. (4) Analyzing method for soil was improved to NaOH-HCl method which has good recovery rate. (5) 90 Y separation method of simple operation was added for sea water analysis besides EDTA and fuming nitric acid methods. (6) Flame spectrometry for quantitative analysis of stable strontium was revised to atomic absorption spectrometry. The contents of the manual comprises 11 chapters describing introduction, measuring criteria for 90 Sr ( 89 Sr), rain and dust, land water, sea water, soil, sea bottom and river bottom sediments (changed from human urine and human bones), crops, milk (the previous one chapter was divided into two), marine organisms, and everyday foods, respectively. (Wakatsuki, Y.)

Positron annihilation in calcium-doped barium titanate

International Nuclear Information System (INIS)

Li, L.T.; Zhang, X.W.; Smyth, D.M.

1987-01-01

The Positron Annihilation Technique (PAT) has been used to study lattice defects in CaO-doped BaTiO/sub 3/ having the general composition BaTi/sub 1-x/Ca/sub x/O/sub 3-x/, with x = 0, 0.005, 0.010, 0.015, and 0.020. The long lifetime, tau/sub 2/, and the mean lifetime, tau/sub m/, of the positrons were both found to increase with increasing Ca content, x, up to x = 0.015-0.020. This is in good agreement wit the solubility limit for Ca on Ti-sites in BaTiO/sub 3/ found by others from measurements of the equilibrium electrical conductivity, and by other investigators from x-ray diffraction studies. In these studies, it was shown that for compositions with (Ba+Ca)/Ti > 1, Ca can be forced to occupy Ti-sites up to 1.5-2%, where it acts as a doubly-charged acceptor center that is compensated by oxygen vacancies. It is suggested that the oxygen vacancies represent places where the annihilation of positrons is delayed because of the low local electron density. These results indicate that the PAT can be a useful tool for the characterization of the defect structure of complex oxides

Conical light scattering in strontium barium niobate crystals related to an intrinsic composition inhomogeneity

International Nuclear Information System (INIS)

Bastwoeste, K; Sander, U; Imlau, M

2007-01-01

Conical light scattering is uncovered in poly- and mono-domain, nominally pure and Eu-doped strontium barium niobate (SBN) crystals over a wide temperature regime. The appearance of two scattering cones, a scattering line and a corona is observed and can be explained comprehensively within the Ewald sphere concept. Photorefraction, scattering from domain boundaries or from growth striations can be excluded from explaining the origin of the scattering. It is shown that the temperature-persistent scattering process is related to a growth-induced seeding rod, i.e. a composition inhomogeneity primarily localized at the centre of the SBN sample. The rod is directed parallel to the c axis and yields a refractive-index inhomogeneity with spatial frequencies on the micro-scale

A silicon doped hafnium oxide ferroelectric p–n–p–n SOI tunneling field–effect transistor with steep subthreshold slope and high switching state current ratio

Directory of Open Access Journals (Sweden)

Saeid Marjani

2016-09-01

Full Text Available In this paper, a silicon–on–insulator (SOI p–n–p–n tunneling field–effect transistor (TFET with a silicon doped hafnium oxide (Si:HfO2 ferroelectric gate stack is proposed and investigated via 2D device simulation with a calibrated nonlocal band–to–band tunneling model. Utilization of Si:HfO2 instead of conventional perovskite ferroelectrics such as lead zirconium titanate (PbZrTiO3 and strontium bismuth tantalate (SrBi2Ta2O9 provides compatibility to the CMOS process as well as improved device scalability. By using Si:HfO2 ferroelectric gate stack, the applied gate voltage is effectively amplified that causes increased electric field at the tunneling junction and reduced tunneling barrier width. Compared with the conventional p–n–p–n SOI TFET, the on–state current and switching state current ratio are appreciably increased; and the average subthreshold slope (SS is effectively reduced. The simulation results of Si:HfO2 ferroelectric p–n–p–n SOI TFET show significant improvement in transconductance (∼9.8X enhancement at high overdrive voltage and average subthreshold slope (∼35% enhancement over nine decades of drain current at room temperature, indicating that this device is a promising candidate to strengthen the performance of p–n–p–n and conventional TFET for a switching performance.

Effect of certain alkaline metals on Pr doped glasses to investigate spectroscopic studies

Science.gov (United States)

Lenkennavar Susheela, K.; Madhu, A.; Eraiah, B.; Kokila, M. K.

2018-02-01

Incorporation of different Alkaline earth metal like Barium, Calcium and strontium in sodium lead borate glass doped with Pr3+ is studied. Physical parameters such as density, molar volume, molar refractivity etc have been evaluated. Effect of different atomic size of alkaline metal using optical and physical parameters is analysed. XRD and FTIR were carried out to know the structural behaviour of the glasses. Absorption and Emission spectra are recorded at room temperature and the results were discussed.

Precipitation-adsorption process for the decontamination of nuclear waste supernates

Science.gov (United States)

Lee, L.M.; Kilpatrick, L.L.

1982-05-19

High-level nuclear waste supernate is decontaminated of cesium by precipitation of the cesium and potassium with sodium tetraphenyl boron. Simultaneously, strontium-90 is removed from the waste supernate sorption of insoluble sodium titanate. The waste solution is then filtered to separate the solution decontaminated of cesium and strontium.

Electron beam irradiation on cation exchanger used for strontium recovery

International Nuclear Information System (INIS)

Watanabe, Sou; Nakamura, Masahiro; Nomura, Kazunori; Nakajima, Yasuo; Okamoto, Yoshihiro

2014-01-01

Titanate is promising material for radioactive Sr recovery from liquid waste generated in the nuclear facilities. "9"0Sr is one of the most important nuclides in order to release the liquid waste into the environment due to its strong beta-ray decay energy. Although the titanate is applied to radioactive Sr decontamination facility, their resistance to irradiations from radioactive elements adsorbed is not widely investigated so far. In this study, durability of a hydrous titanic acid ion exchanger against beta-ray irradiation were evaluated through electron beam irradiation, elution behaviour of Sr after the irradiation and local structural analysis of the titanate. 1.4 MGy irradiation led to 1% of Sr elution, and the elution could be attributed to defects of O in the titanate induced by the irradiation. Chemical state of Ti of the titanate must be stable up to 2.7 MGy irradiation. (author)

Isomorfic Substitutions of Calcium by Strontium in Calcium Hydroxyapatite

International Nuclear Information System (INIS)

Christensen, Hilbert

1962-12-01

By means of homogeneous precipitation it has been possible to synthesize crystalline solid solutions of calcium strontium hydroxyapatite from aqueous solutions. The lattice constants for the solid solutions were measured in the range Ca 9 Sr(PO 4 ) 6 (OH) 2 - CaSr 9 (PO 4 ) 6 (OH) 2 . The investigations show that the discrimination of strontium against calcium is considerably smaller than reported elsewhere (1). Strontium is preferentially built into the c-axis direction of the apatite lattice

Epoxy-based broadband antireflection coating for millimeter-wave optics.

Science.gov (United States)

Rosen, Darin; Suzuki, Aritoki; Keating, Brian; Krantz, William; Lee, Adrian T; Quealy, Erin; Richards, Paul L; Siritanasak, Praween; Walker, William

2013-11-20

We have developed epoxy-based, broadband antireflection coatings for millimeter-wave astrophysics experiments with cryogenic optics. By using multiple-layer coatings where each layer steps in dielectric constant, we achieved low reflection over a wide bandwidth. We suppressed the reflection from an alumina disk to 10% over fractional bandwidths of 92% and 104% using two-layer and three-layer coatings, respectively. The dielectric constants of epoxies were tuned between 2.06 and 7.44 by mixing three types of epoxy and doping with strontium titanate powder required for the high dielectric mixtures. At 140 K, the band-integrated absorption loss in the coatings was suppressed to less than 1% for the two-layer coating, and below 10% for the three-layer coating.

Titan Montgolfiere Terrestrial Test Bed, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — With the Titan Saturn System Mission, NASA is proposing to send a Montgolfiere balloon to probe the atmosphere of Titan. To better plan this mission and create a...

Titan Montgolfiere Terrestrial Test Bed, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — With the Titan Saturn System Mission, NASA is proposing to send a Montgolfiere balloon to probe the atmosphere of Titan. In order to better plan this mission and...

AVIATR—Aerial Vehicle for In-situ and Airborne Titan Reconnaissance

DEFF Research Database (Denmark)

Barnes, Jason W.; Lemke, Lawrence; Foch, Rick

2012-01-01

We describe a mission concept for a stand-alone Titan airplane mission: Aerial Vehicle for In-situ and Airborne Titan Reconnaissance (AVIATR). With independent delivery and direct-to-Earth communications, AVIATR could contribute to Titan science either alone or as part of a sustained Titan...... Exploration Program. As a focused mission, AVIATR as we have envisioned it would concentrate on the science that an airplane can do best: exploration of Titan's global diversity. We focus on surface geology/hydrology and lower-atmospheric structure and dynamics. With a carefully chosen set of seven...... of a Space Vehicle (SV) for cruise, an Entry Vehicle (EV) for entry and descent, and the Air Vehicle (AV) to fly in Titan's atmosphere. Using an Earth-Jupiter gravity assist trajectory delivers the spacecraft to Titan in 7.5 years, after which the AVIATR AV would operate for a 1-Earth-year nominal mission...

HST observations of the limb polarization of Titan

Science.gov (United States)

Bazzon, A.; Schmid, H. M.; Buenzli, E.

2014-12-01

Context. Titan is an excellent test case for detailed studies of the scattering polarization from thick hazy atmospheres. Accurate scattering and polarization parameters have been provided by the in situ measurements of the Cassini-Huygens landing probe. For Earth-bound observations Titan can only be observed at a backscattering situation, where the disk-integrated polarization is close to zero. However, with resolved imaging polarimetry a second order polarization signal along the entire limb of Titan can be measured. Aims: We present the first limb polarization measurements of Titan, which are compared as a test to our limb polarization models. Methods: Previously unpublished imaging polarimetry from the HST archive is presented, which resolves the disk of Titan. We determine flux-weighted averages of the limb polarization and radial limb polarization profiles, and investigate the degradation and cancelation effects in the polarization signal due to the limited spatial resolution of our observations. Taking this into account we derive corrected values for the limb polarization in Titan. The results are compared with limb polarization models, using atmosphere and haze scattering parameters from the literature. Results: In the wavelength bands between 250 nm and 2 μm a strong limb polarization of about 2 - 7% is detected with a position angle perpendicular to the limb. The fractional polarization is highest around 1 μm. As a first approximation, the polarization seems to be equally strong along the entire limb. The comparison of our data with model calculations and the literature shows that the detected polarization is compatible with expectations from previous polarimetric observations taken with Voyager 2, Pioneer 11, and the Huygens probe. Conclusions: Our results indicate that ground-based monitoring measurements of the limb-polarization of Titan could be useful for investigating local haze properties and the impact of short-term and seasonal variations of

Photoluminescence properties and energy-transfer of thermal-stable Ce3+, Mn2+-codoped barium strontium lithium silicate red phosphors

International Nuclear Information System (INIS)

Zhang Xinguo; Gong Menglian

2011-01-01

Research highlights: → Excited by UV, strong red luminescence is observed from Ce 3+ , Mn 2+ -codoped barium strontium lithium silicate (BSLS), while violet-blue emission from Ce 3+ sole doped BSLS. → These results indicate the Mn 2+ -derived red emission is originated by an efficient Ce 3+ → Mn 2+ energy transfer. → The red emission becomes stronger with increased Sr content, and shows red-shift. → These phosphors demonstrate good thermal stability even in 180 o C, which is suitable for NUV LED application. - Abstract: A series of thermal-stable Ce 3+ , Mn 2+ -codoped barium strontium lithium silicate (BSLS) phosphors was synthesized by a high-temperature solid-state reaction. The XRD patterns of this phosphor seem to be a new phase that has not been reported before. BSLS:Ce 3+ , Mn 2+ showed two emission bands under 365 nm excitation: one observed at 421 nm was attributed to Ce 3+ emission, and the other found in red region was assigned to Mn 2+ emission through Ce 3+ -Mn 2+ efficient energy transfer. The Mn 2+ emission shifted red along with the replacement of barium by strontium, which was due to the change of crystal field. A composition-optimized phosphor, BSLS:0.10Ce 3+ , 0.05Mn 2+ (Ba = 65), exhibited strong and broad red-emitting and supreme thermal stability. The results suggest that this phosphor is suitable as a red component for NUV LED or high pressure Hg vapor (HPMV) lamp.

Experimental basis for a Titan probe organic analysis

International Nuclear Information System (INIS)

Mckay, C.P.; Scattergood, T.W.; Borucki, W.J.; Kasting, J.F.; Miller, S.L.; California Univ., San Diego, La Jolla)

1986-01-01

The recent Voyager flyby of Titan produced evidence for at least nine organic compounds in that atmosphere that are heavier than methane. Several models of Titan's atmosphere, as well as laboratory simulations, suggest the presence of organics considerably more complex that those observed. To ensure that the in situ measurements are definitive with respect to Titan's atmosphere, experiment concepts, and the related instrumentation, must be carefully developed specifically for such a mission. To this end, the possible composition of the environment to be analyzed must be bracketed and model samples must be provided for instrumentation development studies. Laboratory studies to define the optimum flight experiment and sampling strategy for a Titan entry probe are currently being conducted. Titan mixtures are being subjected to a variety of energy sources including high voltage electron from a DC discharge, high current electric shock, and laser detonation. Gaseous and solid products are produced which are then analyzed. Samples from these experiements are also provided to candidate flight experiments as models for instrument development studies. Preliminary results show that existing theoretical models for chemistry in Titan's atmosphere cannot adequetely explain the presence and abundance of all trace gases observed in these experiments

Morphological control of strontium oxalate particles by PSMA-mediated precipitation reaction

Energy Technology Data Exchange (ETDEWEB)

Yu Jiaguo [State Key Laboratory of Advanced Technology for Material Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China)]. E-mail: jiaguoyu@yahoo.com; Tang Hua [State Key Laboratory of Advanced Technology for Material Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Cheng Bei [State Key Laboratory of Advanced Technology for Material Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China)

2005-05-15

In this paper, strontium oxalate particles with different morphologies could be easily obtained by a precipitation reaction of sodium oxalate with strontium chloride in the absence and presence of poly-(styrene-alt-maleic acid) (PSMA). The as-prepared products were characterized with scanning electron microscopy and X-ray diffraction. The effects of pH, aging time and concentration of PSMA on the phase structures and morphologies of the as-prepared strontium oxalate particles were investigated and discussed. The results showed that strontium oxalate particles with various morphologies, such as, bi-pyramids, rods, peanuts, and spherical particles, etc., could be obtained by varying the experimental conditions. PSMA promoted the formation of strontium oxalate dihydrate (SOD) phase. Suitable pH values (pH 7 and 8) favor the formation of the peanut-shaped SrC{sub 2}O{sub 4} particles. This research may provide new insight into the control of morphologies and phase structures of strontium oxalate particles and the biomimetic synthesis of novel inorganic materials.

History and challenges of barium titanate: Part I

Directory of Open Access Journals (Sweden)

Vijatović M.M.

2008-01-01

Full Text Available Barium titanate is the first ferroelectric ceramics and a good candidate for a variety of applications due to its excellent dielectric, ferroelectric and piezoelectric properties. Barium titanate is a member of a large family of compounds with the general formula ABO3 called perovskites. Barium titanate can be prepared using different methods. The synthesis method depends on the desired characteristics for the end application. The used method has a significant influence on the structure and properties of barium titanate materials. In this review paper, Part I contains a study of the BaTiO3 structure and frequently used synthesis methods.

Titan's organic chemistry: Results of simulation experiments

Science.gov (United States)

Sagan, Carl; Thompson, W. Reid; Khare, Bishun N.

1992-01-01

Recent low pressure continuous low plasma discharge simulations of the auroral electron driven organic chemistry in Titan's mesosphere are reviewed. These simulations yielded results in good accord with Voyager observations of gas phase organic species. Optical constants of the brownish solid tholins produced in similar experiments are in good accord with Voyager observations of the Titan haze. Titan tholins are rich in prebiotic organic constituents; the Huygens entry probe may shed light on some of the processes that led to the origin of life on Earth.

The commercial evolution of the Titan program

Science.gov (United States)

Isakowitz, Steven

1988-07-01

The present status evaluation of proprietary efforts to turn the once exclusively government-requirements-oriented Titan launch vehicle into a successful commercial competitor is divided into three phases. The first phase notes recent changes in U.S. space transportation policy and the Titan configurations evaluated for commercial feasibility. The second phase is a development history for the current vehicle's marketing organization and the right-to-use agreement for a launch site. Phase three projects the prospective marketing climate for a commercial Titan vehicle and its planned improvements.

Surface adsorption in strontium chloride ammines

DEFF Research Database (Denmark)

Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata

2013-01-01

An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammonia...... desorption originating from the adsorbed state is directly observed below the bulk desorption temperature, as confirmed by density functional theory calculations. The desorption enthalpy of the adsorbed state of strontium chloride octa-ammine is determined with both techniques to be around 37-39 k...

Preparation and characterization of titanate nanotubes/carbon composites

International Nuclear Information System (INIS)

Wang Xiaodong; Pan Hui; Xue Xiaoxiao; Qian Junjie; Yu Laigui; Yang Jianjun; Zhang Zhijun

2011-01-01

Highlights: → Titanate nanotubes/carbon composites were synthesized from TiO 2 -carbon composites. → The carbon shell of TiO 2 particles obstructed the reaction between TiO 2 and NaOH. → TEM, XRD, and Raman spectra reveal the formation processes of the TNT/CCs. - Abstract: Titanate nanotubes/carbon composites(TNT/CCs) were synthesized by allowing carbon-coated TiO 2 (CCT) powder to react with a dense aqueous solution of NaOH at 120 deg. C for a proper period of time. As-prepared CCT and TNT/CCs were characterized by means of transmission electron microscopy (TEM), X-ray diffraction (XRD), and Raman spectrometry. The processes for formation of titanate nanotubes/carbon composites were discussed. It was found that the TiO 2 particles in TiO 2 -carbon composite were enwrapped by a fine layer of carbon with a thickness of about 4 nm. This carbon layer functioned to inhibit the transformation from anatase TiO 2 to orthorhombic titanate. As a result, the anatase TiO 2 in CCT was incompletely transformed into orthorhombic titanate nanotubes upon 24 h of reaction in the dense and hot NaOH solution. When the carbon layers were gradually peeled off along with the formation of more orthorhombic titanate nanotubes at extended reaction durations (e.g., 72 h), anatase TiO 2 particles in CCT were completely transformed into orthorhombic titanate nanotubes, yielding TNT/CCs whose morphology was highly dependent on the reaction time and temperature.