WorldWideScience

Sample records for doped gallium arsenide

  1. Probing the electronic properties of p-doped gallium arsenide nanowires

    OpenAIRE

    2014-01-01

    Probing the electronic properties of nm-scaled object is a challenge but is required for doping optimalization and using the nm-scaled objects as building blocks in future devices. In the present study, electron beam induced deposition of platinum was used for contacting and creating two-point probes to beryllium-doped gallium arsenide nanowires. Thereby, a metal-semiconductor-metal structure with rectifying metal-semiconductor contact characteristic is formed (i.e. back-to-back Schottky diod...

  2. Gallium Arsenide Photocathode Development

    Science.gov (United States)

    1975-10-01

    r ~\\ 1 1 AD-A018 619 ■ i I 1 GALLIUM ARSENIDE PHOTOCATHODE DEVELOPMENT I Terry Roach, et al 1 1 ■f EPSCO ...aiwiiwnHWlffl’Wip m, «swwerf^MW^S’ GALLIUM ARSENIDE PHOTOCATHODE DEVELOPMENT T. J. Roach Bianca Contractor: EPSCO Laboratories Contract Number: F08606...PHOTOCATHODE DEVELOPMENT 7. AUTHORfaJ T. Roach J. Bianca t. PERFORMING ORGANIZATION NAME AND AOORESS EPSCO Laboratories 227 High Ridge Road Stauford CT

  3. An effective electron mass in heavily doped gallium arsenide under ordering impurity complexes

    CERN Document Server

    Bogdanova, V A; Semikolenova, N A; Sidorov, E N

    2002-01-01

    The results of an investigation of edge photoluminescence spectra at 300 K for series of Czochralski grown tellurium doped gallium arsenide monocrystals with free carriers concentration n sub 0 = 10 sup 1 sup 7 -10 sup 1 sup 9 cm sup - sup 3 are presented. On the basis of photoluminescence spectra contour analysis the concentration dependences of chemical potential and value of band gap narrowing are obtained. The concentration dependence of electron effective mass m* sub 0 (n sub 0) at the bottom of the conduction band is calculated. It is shown, that the nonmonotonous dependence m* sub 0 (n sub 0) is an accordance with electron scattering data in the material under study and is conditioned by ordering of impurity complexes

  4. Gallium Arsenide Domino Circuit

    Science.gov (United States)

    Yang, Long; Long, Stephen I.

    1990-01-01

    Advantages include reduced power and high speed. Experimental gallium arsenide field-effect-transistor (FET) domino circuit replicated in large numbers for use in dynamic-logic systems. Name of circuit denotes mode of operation, which logic signals propagate from each stage to next when successive stages operated at slightly staggered clock cycles, in manner reminiscent of dominoes falling in a row. Building block of domino circuit includes input, inverter, and level-shifting substages. Combinational logic executed in input substage. During low half of clock cycle, result of logic operation transmitted to following stage.

  5. Doped Aluminum Gallium Arsenide (AlGaAs)/Gallium Arsenide (GaAs) Photoconductive Semiconductor Switch (PCSS) Fabrication

    Science.gov (United States)

    2016-09-27

    substrate and the first layer, regardless of pregrowth surface treatments or growth technology . Epilayer defect density and unintentional doping increase...stress bubble and hash-mark or crack tensile defects. The ammonia (NH3) to silane (SiH4) ratio optimizes the index to a SiNx slightly rich in Si over the...Conference, Tampa, FL, 2009. 7. Filmtronics: Spin-on diffusant, zinc film— product code 980. Butler (PA): Filmtronics Inc.; 2004 Jul [accessed 2016

  6. Development of a Multi-layer Anti-reflective Coating for Gallium Arsenide/Aluminum Gallium Arsenide Solar Cells

    Science.gov (United States)

    2015-07-01

    Aluminum Gallium Arsenide Solar Cells by Kimberley A Olver Approved for public release; distribution unlimited...Development of a Multi-layer Anti-reflective Coating for Gallium Arsenide/Aluminum Gallium Arsenide Solar Cells by Kimberley A Olver...Aluminum Gallium Arsenide (AlGaAs) Solar Cells 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Kimberley A Olver

  7. Superconductor-semiconductor-superconductor planar junctions of aluminium on DELTA-doped gallium arsenide

    DEFF Research Database (Denmark)

    Taboryski, Rafael Jozef; Clausen, Thomas; Kutchinsky, jonatan

    1997-01-01

    We have fabricated and characterized planar superconductor-semiconductor-superconductor (S-Sm-S) junctions with a high quality (i.e. low barrier) interface between an n++ modulation doped conduction layer in MBE grown GaAs and in situ deposited Al electrodes. The Schottky barrier at the S...

  8. Ellipsometric study of silicon nitride on gallium arsenide

    Science.gov (United States)

    Alterovitz, S. A.; Bu-Abbud, G. H.; Woollam, J. A.; Liu, D.; Chung, Y.; Langer, D.

    1982-01-01

    A method for optimizing the sensitivity of ellipsometric measurements for thin dielectric films on semiconductors is described in simple physical terms. The technique is demonstrated for the case of sputtered silicon nitride films on gallium arsenide.

  9. Superlattice Intermediate Band Solar Cell on Gallium Arsenide

    Science.gov (United States)

    2015-02-09

    AFRL-RV-PS- AFRL-RV-PS- TR-2015-0048 TR-2015-0048 SUPERLATTICE INTERMEDIATE BAND SOLAR CELL ON GALLIUM ARSENIDE Alexandre Freundlich...SUBTITLE 5a. CONTRACT NUMBER FA9453-13-1-0232 Superlattice Intermediate Band Solar Cell on Gallium Arsenide 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER...band solar cell incorporating low dimensional structures made with dilute nitrogen alloys of III-V semiconductors is investigated theoretically and

  10. Inhalation developmental toxicology studies: Gallium arsenide in mice and rats

    Energy Technology Data Exchange (ETDEWEB)

    Mast, T.J.; Greenspan, B.J.; Dill, J.A.; Stoney, K.H.; Evanoff, J.J.; Rommereim, R.L.

    1990-12-01

    Gallium arsenide is a crystalline compound used extensively in the semiconductor industry. Workers preparing solar cells and gallium arsenide ingots and wafers are potentially at risk from the inhalation of gallium arsenide dust. The potential for gallium arsenide to cause developmental toxicity was assessed in Sprague- Dawley rats and CD-1 (Swiss) mice exposed to 0, 10, 37, or 75 mg/m{sup 3} gallium arsenide, 6 h/day, 7 days/week. Each of the four treatment groups consisted of 10 virgin females (for comparison), and {approx}30 positively mated rats or {approx}24 positively mated mice. Mice were exposed on 4--17 days of gestation (dg), and rats on 4--19 dg. The day of plug or sperm detection was designated as 0 dg. Body weights were obtained throughout the study period, and uterine and fetal body weights were obtained at sacrifice (rats, 20 dg; mice, 18 dg). Implants were enumerated and their status recorded. Live fetuses were sexed and examined for gross, visceral, skeletal, and soft-tissue craniofacial defects. Gallium and arsenic concentrations were determined in the maternal blood and uterine contents of the rats (3/group) at 7, 14, and 20 dg. 37 refs., 11 figs., 30 tabs.

  11. Impurities interactions in the crytal growth of LEC gallium arsenides

    Energy Technology Data Exchange (ETDEWEB)

    Mucchino, C. [Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC; Goeroeg, T. [Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC; Zanotti, L. [Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC; Mignoni, G. [Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC; Catellani, A. [Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC

    1996-06-01

    The control of low level impurities is still considered to play a key role in obtaining GaAs based devices with an high degree of uniformity and reproducibility. Although in the recent years the importance of appropriate post growth thermal treatments has been recognized as the most relevant step in achieving homogeneous material, the contamination reduction of the melt is a fundamental requisite for growing crystals with good electric characteristics and morphology. In this work we report on new results obtained from boron and silicon doped gallium arsenide crystals grown by LEC technique in a high pressure puller: different doping procedures for heavily Si doped crystals are described and interactions between silicon and boron in the liquid, are discussed together with the analysis of their distribution in the ingot. On the basis of our experimental data from crystals doped with either B or B and Si together, a tentative explanation of the incorporation mechanism of such elements is given and a comparison with previously reported results is made. (orig.)

  12. Boron, bismuth co-doping of gallium arsenide and other compounds for photonic and heterojunction bipolar transistor devices

    Energy Technology Data Exchange (ETDEWEB)

    Mascarenhas, Angelo

    2017-08-01

    Isoelectronic co-doping of semiconductor compounds and alloys with acceptors and deep donors is used to decrease bandgap, to increase concentration of the dopant constituents in the resulting alloys, and to increase carrier mobilities lifetimes. For example, Group III-V compounds and alloys, such as GaAs and GaP, are isoelectronically co-doped with, for example, B and Bi, to customize solar cells, and other semiconductor devices. Isoelectronically co-doped Group II-VI compounds and alloys are also included.

  13. Boron, bismuth co-doping of gallium arsenide and other compounds for photonic and heterojunction bipolar transistor devices

    Science.gov (United States)

    Mascarenhas, Angelo

    2015-07-07

    Isoelectronic co-doping of semiconductor compounds and alloys with acceptors and deep donors is sued to decrease bandgap, to increase concentration of the dopant constituents in the resulting alloys, and to increase carrier mobilities lifetimes. For example, Group III-V compounds and alloys, such as GaAs and GaP, are isoelectronically co-doped with, for example, B and Bi, to customize solar cells, and other semiconductor devices. Isoelectronically co-doped Group II-VI compounds and alloys are also included.

  14. Determination of the Peltier coefficient for gallium arsenide in a vertical Bridgman furnace

    Science.gov (United States)

    Wiegel, Michaela E. K.; Matthiesen, David H.

    2011-10-01

    The Peltier coefficient for gallium arsenide solid in contact with its melt was experimentally determined. Selenium doped gallium arsenide samples were hermetically sealed in a fused quartz ampoule and processed in a vertical Bridgman furnace. During the translation period seven sequences of current-on and current-off periods were processed into the solidifying crystal. An axial slice was mechanochemically polished and then etched. Photomicrographs of the slice were taken with differential interference contrast microscopy and were used to measure the thickness of the current-on and current-off layers. These results were used to calculate growth rates from which the Peltier coefficient was calculated. An average value of 0.107±0.015 V was determined. The values calculated from the different sequences were in excellent agreement with each other even though the sequences had different current densities, current-on durations, and current-on to current-off ratios.

  15. The comparison between gallium arsenide and indium gallium arsenide as materials for solar cell performance using Silvaco application

    Energy Technology Data Exchange (ETDEWEB)

    Zahari, Suhaila Mohd; Norizan, Mohd Natashah; Mohamad, Ili Salwani; Osman, Rozana Aina Maulat; Taking, Sanna [School of Microelectronic Engineering, Universiti Malaysia Perlis, Kampus Pauh Putra, 02600 Arau, Perlis (Malaysia)

    2015-05-15

    The work presented in this paper is about the development of single and multilayer solar cells using GaAs and InGaAs in AM1.5 condition. The study includes the modeling structure and simulation of the device using Silvaco applications. The performance in term of efficiency of Indium Gallium Arsenide (InGaAs) and GaAs material was studied by modification of the doping concentration and thickness of material in solar cells. The efficiency of the GaAs solar cell was higher than InGaAs solar cell for single layer solar cell. Single layer GaAs achieved an efficiency about 25% compared to InGaAs which is only 2.65% of efficiency. For multilayer which includes both GaAs and InGaAs, the output power, P{sub max} was 8.91nW/cm² with the efficiency only 8.51%. GaAs is one of the best materials to be used in solar cell as a based compared to InGaAs.

  16. A Review of Liquid Phase Epitaxial Grown Gallium Arsenide

    OpenAIRE

    Alexiev, D.; Prokopovich, D. A.; Thomson, S.; Mo, L.; Rosenfeld, A B; Reinhard, M

    2004-01-01

    Liquid phase epitaxy of gallium arsenide (LPE GaAs) has been investigated intensively from the late 1960's to the present and has now a special place in the manufacture of wide band, compound semiconductor radiation detectors. Although this particular process appears to have gained prominence in the last three decades, it is interesting to note that its origins reach back to 1836 when Frankenheim made his first observations. A brief review is presented from a semiconductor applications point ...

  17. Thermal cycling, DLTS, and PEC studies on LEC gallium arsenide. [GaAs:Si

    Energy Technology Data Exchange (ETDEWEB)

    Santhanaraghavan, P. (Anna Univ., Madras (India). Crystal Growth Centre); Sankaranarayanan, K. (Anna Univ., Madras (India). Crystal Growth Centre); Arokiaraj, J. (Anna Univ., Madras (India). Crystal Growth Centre); Anbukumar, S. (Anna Univ., Madras (India). Crystal Growth Centre); Kumar, J. (Anna Univ., Madras (India). Crystal Growth Centre); Ramasamy, P. (Anna Univ., Madras (India). Crystal Growth Centre)

    1994-01-01

    This paper discusses the growth of gallium arsenide single crystals using the LEC technique. The Semi-insulating gallium arsenide was studied. The defect investigations were made by DLTS and etching studies. The variation of deep level concentration along the wafer was estimated using DLTS. The fabrication and efficiency of the PEC Solar cells are also reported. (orig.)

  18. Anomalous tensoelectric effects in gallium arsenide tunnel diodes

    Energy Technology Data Exchange (ETDEWEB)

    Alekseeva, Z.M.; Vyatkin, A.P.; Krivorotov, N.P.; Shchegol' , A.A.

    1988-02-01

    Anomalous tensoelectric phenomena induced in a tunnel p-n junction by a concentrated load and by hydrostatic compression were studied. The anomalous tensoelectric effects are caused by the action of concentrators of mechanical stresses in the vicinity of the p-n junction, giving rise to local microplastic strain. Under the conditions of hydrostatic compression prolate inclusions approx.100-200 A long play the role of concentrators. Analysis of irreversible changes in the current-voltage characteristics of tunnel p-n junctions made it possible to separate the energy levels of the defects produced with plastic strain of gallium arsenide.

  19. Laser and electron beam processing of silicon and gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Narayan, J.

    1979-10-01

    Laser (photon) and electron beams provide a controlled source of heat by which surface layers of silicon and gallium arsenide can be rapidly melted and cooled with rates exceeding 10/sup 80/C/sec. The melting process has been used to remove displacement damage in ion implanted Si and GaAs, to remove dislocations, loops and precipitates in silicon and to study impurity segregation and solubility limits. The mechanisms associated with various phenomena will be examined. The possible impact of laser and electron beam processing on device technology, particularly with respect to solar cells is discussed.

  20. Macroscopic diffusion models for precipitation in crystalline gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Kimmerle, Sven-Joachim Wolfgang

    2009-09-21

    Based on a thermodynamically consistent model for precipitation in gallium arsenide crystals including surface tension and bulk stresses by Dreyer and Duderstadt, we propose two different mathematical models to describe the size evolution of liquid droplets in a crystalline solid. The first model treats the diffusion-controlled regime of interface motion, while the second model is concerned with the interface-controlled regime of interface motion. Our models take care of conservation of mass and substance. These models generalise the well-known Mullins- Sekerka model for Ostwald ripening. We concentrate on arsenic-rich liquid spherical droplets in a gallium arsenide crystal. Droplets can shrink or grow with time but the centres of droplets remain fixed. The liquid is assumed to be homogeneous in space. Due to different scales for typical distances between droplets and typical radii of liquid droplets we can derive formally so-called mean field models. For a model in the diffusion-controlled regime we prove this limit by homogenisation techniques under plausible assumptions. These mean field models generalise the Lifshitz-Slyozov-Wagner model, which can be derived from the Mullins-Sekerka model rigorously, and is well understood. Mean field models capture the main properties of our system and are well adapted for numerics and further analysis. We determine possible equilibria and discuss their stability. Numerical evidence suggests in which case which one of the two regimes might be appropriate to the experimental situation. (orig.)

  1. Nuclear Magnetic Resonance in Gallium Arsenide.

    Science.gov (United States)

    1987-05-19

    dependance of the second moment of the line- shapes on the orientation of the crystal in the field supports a continuous solid model of the strain, in which...visible in the lightly doped sample. Hester, Sher, Soest, and Weisz have shown that, assuming first order broadening, the angular dependance of the second...this study. The second moments found agreed qualitatively with those found by Hester, Sher, Soest, and Weisz in their 3angular dependance . However

  2. Temperature dependence of carrier capture by defects in gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Wampler, William R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Modine, Normand A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    This report examines the temperature dependence of the capture rate of carriers by defects in gallium arsenide and compares two previously published theoretical treatments of this based on multi phonon emission (MPE). The objective is to reduce uncertainty in atomistic simulations of gain degradation in III-V HBTs from neutron irradiation. A major source of uncertainty in those simulations is poor knowledge of carrier capture rates, whose values can differ by several orders of magnitude between various defect types. Most of this variation is due to different dependence on temperature, which is closely related to the relaxation of the defect structure that occurs as a result of the change in charge state of the defect. The uncertainty in capture rate can therefore be greatly reduced by better knowledge of the defect relaxation.

  3. Ultrafast photocurrents and terahertz radiation in gallium arsenide and carbon based nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Prechtel, Hans Leonhard

    2011-08-15

    In this thesis we developed a measurement technique based on a common pump-probe scheme and coplanar stripline circuits that enables time-resolved photocurrent measurements of contacted nanosystems with a micrometer spatial and a picosecond time resolution. The measurement technique was applied to lowtemperature grown gallium arsenide (LT-GaAs), carbon nanotubes (CNTs), graphene, and p-doped gallium arsenide (GaAs) nanowires. The various mechanisms responsible for the generation of current pulses by pulsed laser excitation were reviewed. Furthermore the propagation of the resulting electromagnetic radiation along a coplanar stripline circuit was theoretically and numerically treated. The ultrafast photocurrent response of low-temperature grown GaAs was investigated. We found two photocurrent pulses in the time-resolved response. We showed that the first pulse is consistent with a displacement current pulse. We interpreted the second pulse to result from a transport current process. We further determined the velocity of the photo-generated charge carriers to exceed the drift, thermal and quantum velocities of single charge carriers. Hereby, we interpreted the transport current pulse to stem from an electron-hole plasma excitation. We demonstrated that the photocurrent response of CNTs comprises an ultrafast displacement current and a transport current. The data suggested that the photocurrent is finally terminated by the recombination lifetime of the charge carriers. To the best of our knowledge, we presented in this thesis the first recombination lifetime measurements of contacted, suspended, CVD grown CNT networks. In addition, we studied the ultrafast photocurrent dynamics of freely suspended graphene contacted by metal electrodes. At the graphene-metal interface, we demonstrated that built-in electric fields give rise to a photocurrent with a full-width-half-maximum of a few picoseconds and that a photo-thermoelectric effect generates a current with a decay time

  4. Gallium arsenide pilot line for high performance components

    Science.gov (United States)

    1990-01-01

    The Gallium Arsenide Pilot Line for High Performance Components (Pilot Line III) is to develop a facility for the fabrication of GaAs logic and memory chips. The first thirty months of this contract are now complete, and this report covers the period from March 27 through September 24, 1989. Similar to the PT-2M SRAM function for memories, the six logic circuits of PT-2L and PT-2M have served their functions as stepping stones toward the custom, standard cell, and cell array logic circuits. All but one of these circuits was right first time; the remaining circuit had a layout error due to a bug in the design rule checker that has since been fixed. The working devices all function over the full temperature range from -55 to 125 C. They all comfortably meet the 200 MHz requirement. They do not solidly conform to the required input and output voltage levels, particularly Vih. It is known that these circuits were designed with the older design models and that they came from an era where the DFET thresholds were often not on target.

  5. Gallium Arsenide (GaAs) Quantum Photonic Waveguide Circuits

    CERN Document Server

    Wang, Jianwei; Jiang, Pisu; Bonneau, Damien; Engin, Erman; Silverstone, Joshua W; Lermer, Matthias; Beetz, Johannes; Kamp, Martin; Hofling, Sven; Tanner, Michael G; Natarajan, Chandra M; Hadfield, Robert H; Dorenbos, Sander N; Zwiller, Val; O'Brien, Jeremy L; Thompson, Mark G

    2014-01-01

    Integrated quantum photonics is a promising approach for future practical and large-scale quantum information processing technologies, with the prospect of on-chip generation, manipulation and measurement of complex quantum states of light. The gallium arsenide (GaAs) material system is a promising technology platform, and has already successfully demonstrated key components including waveguide integrated single-photon sources and integrated single-photon detectors. However, quantum circuits capable of manipulating quantum states of light have so far not been investigated in this material system. Here, we report GaAs photonic circuits for the manipulation of single-photon and two-photon states. Two-photon quantum interference with a visibility of 94.9 +/- 1.3% was observed in GaAs directional couplers. Classical and quantum interference fringes with visibilities of 98.6 +/- 1.3% and 84.4 +/- 1.5% respectively were demonstrated in Mach-Zehnder interferometers exploiting the electro-optic Pockels effect. This w...

  6. Surface-enhanced gallium arsenide photonic resonator with a quality factor of six million

    CERN Document Server

    Guha, Biswarup; Cadiz, Fabian; Morgenroth, Laurence; Ulin, Vladimir; Berkovitz, Vladimir; Lemaître, Aristide; Gomez, Carmen; Amo, Alberto; Combrié, Sylvian; Gérard, Bruno; Leo, Giuseppe; Favero, Ivan

    2016-01-01

    Gallium Arsenide and related compound semiconductors lie at the heart of optoelectronics and integrated laser technologies. Shaped at the micro and nano-scale, they allow strong interaction with quantum dots and quantum wells, and promise to result in stunning devices. However gallium arsenide optical structures presently exhibit lower performances than their silicon-based counterparts, notably in nanophotonics where the surface plays a chief role. Here we report on advanced surface control of miniature gallium arsenide optical resonators, using two distinct techniques that produce permanent results. One leads to extend the lifetime of free-carriers and enhance luminescence, while the other strongly reduces surface absorption originating from mid-gap states and enables ultra-low optical dissipation devices. With such surface control, the quality factor of wavelength-sized optical disk resonators is observed to rise up to six million at telecom wavelength, greatly surpassing previous realizations and opening n...

  7. A study of the applicability of gallium arsenide and silicon carbide as aerospace sensor materials

    Science.gov (United States)

    Hurley, John S.

    1990-01-01

    Most of the piezoresistive sensors, to date, are made of silicon and germanium. Unfortunately, such materials are severly restricted in high temperature environments. By comparing the effects of temperature on the impurity concentrations and piezoresistive coefficients of silicon, gallium arsenide, and silicon carbide, it is being determined if gallium arsenide and silicon carbide are better suited materials for piezoresistive sensors in high temperature environments. The results show that the melting point for gallium arsenide prevents it from solely being used in high temperature situations, however, when used in the alloy Al(x)Ga(1-x)As, not only the advantage of the wider energy band gas is obtained, but also the higher desire melting temperature. Silicon carbide, with its wide energy band gap and higher melting temperature suggests promise as a high temperature piezoresistive sensor.

  8. Magnetoelectric effect in layered structures of amorphous ferromagnetic alloy and gallium arsenide

    Science.gov (United States)

    Bichurin, M. I.; Petrov, V. M.; Leontiev, V. S.; Ivanov, S. N.; Sokolov, O. V.

    2017-02-01

    A paper devotes to theoretical and experimental studying the magnetoelectric interaction in layered structures of amorphous ferromagnetic alloy and single- crystal gallium arsenide. The authors investigated the magnetoelectric effect in the (100) plane of gallium arsenide in the electromechanical resonance range of 200-240 kHz and obtained maximal ME voltage coefficient of 120 V/A at bias field equaled 3.6 kA/m for the direction parallel to the [011] axis. Also the magnetoelectric effect in the (110) and (111) planes is discussed. The results can be used for design of new electronic devices based on the magnetostrictive-semiconductor materials.

  9. Excitation and De-Excitation Mechanisms of ER - Gallium Arsenide and Aluminum Gallium Arsenide

    Science.gov (United States)

    Elsaesser, David William

    Electrical and optical characterization have been performed on GaAs and Al_{rm x}Ga_{rm 1-x} As samples doped with Er either by ion implantation and during Molecular Beam Epitaxial (MBE) growth. The electrical techniques of Deep Level Transient Spectroscopy (DLTS) and Temperature-Dependent Hall Effect (TDH) indicated that Er primarily formed two electrically active centers in both materials. The first center gave rise to a hole trap at E_{rm v} + 35 meV, which was thought to be due to Er substituting for a Ga atom (Er_{rm Ga}) and giving rise to an isoelectronic impurity potential. The second center also gave rise to a hole trap at approximately E_{rm v} + 360 meV, and was attributed to an Er atom occupying an interstitial position (Er_{rm i}). Annealing studies performed on Er-implanted GaAs indicated that the Er_{rm Ga} center preferentially formed at higher annealing temperatures (> 850^circC), with the Er_{rm i} reaching a maximum concentration at an annealing temperature of around 750^circC. Additionally, optical characterization performed by Photoluminescence (PL) measurements showed that the Er_{ rm i} center gave much stronger Er-related emissions due to the transition ^4I _{13/2} to ^4 I_{15/2} in the unfilled Er^{3+}-4f shell than was observed for 4f-emissions associated with the Er_{rm Ga} center. Mechanisms for the excitation and de-excitation of the Er-4f shell in GaAs, consistent with all experimental observations, were proposed. DLTS measurements also detected the presence of a large concentration of Ga-antisite (Ga_ {rm As}) defects as well as As-interstitial (As_{rm i}) defects. Based upon reports of Er^{3+} -4f emissions from four distinct Er-centers, two other likely Er-centers were proposed, Er_{rm Ga}-Ga_{rm As} and Er_{rm Ga} -As_{rm i}. Finally, electrical and optical characterization of Er-doped MBE -grown Al_{0.5}Ga _{rm 0.5}As indicated that the solubility limit of Er in this material was possibly as high as 2 times 10^ {19} cm^{-3}, as

  10. Progress to a Gallium-Arsenide Deep-Center Laser

    Directory of Open Access Journals (Sweden)

    Janet L. Pan

    2009-10-01

    Full Text Available Although photoluminescence from gallium-arsenide (GaAs deep-centers was first observed in the 1960s, semiconductor lasers have always utilized conduction-to-valence-band transitions. Here we review recent materials studies leading to the first GaAs deep-center laser. First, we summarize well-known properties: nature of deep-center complexes, Franck-Condon effect, hotoluminescence. Second, we describe our recent work: insensitivity of photoluminescence with heating, striking differences between electroluminescence and photoluminescence, correlation between transitions to deep-states and absence of bandgap-emission. Room-temperature stimulated-emission from GaAs deep-centers was observed at low electrical injection, and could be tuned from the bandgap to half-the-bandgap (900–1,600 nm by changing the electrical injection. The first GaAs deep-center laser was demonstrated with electrical injection, and exhibited a threshold of less than 27 mA/cm2 in continuous-wave mode at room temperature at the important 1.54 μm fiber-optic wavelength. This small injection for laser action was explained by fast depopulation of the lower state of the optical transition (fast capture of free holes onto deep-centers, which maintains the population inversion. The evidence for laser action included: superlinear L-I curve, quasi-Fermi level separations satisfying Bernard-Duraffourg’s criterion, optical gains larger than known significant losses, clamping of the optical-emission from lossy modes unable to reach laser action, pinning of the population distribution during laser action.

  11. Noise suppression and long-range exchange coupling for gallium arsenide spin qubits

    DEFF Research Database (Denmark)

    Malinowski, Filip

    to put the highest, up to date, lower bound on the electron spin coherence time in gallium arsenide: 870 ms. Later, we study the perspectives of exploiting a multielectron quantum dot as a mediator of the exchange interaction. We investigate interaction between a single spin and the multelectron quantum...

  12. An advanced space photovoltaic concentrator array using Fresnel lenses, gallium arsenide cells, and prismatic cell covers

    Science.gov (United States)

    O'Neill, Mark J.; Piszczor, Michael F.

    1988-01-01

    The current status of a space concentrator array which uses refractive optics, gallium arsenide cells, and prismatic cell covers to achieve excellent performance at a very low array mass is documented. The prismatically covered cells have established records for space cell performance (24.2 percent efficient at 100 AM0 suns and 25 C) and terrestrial single-junction cell performance (29.3 percent efficient at 200 AM1.5 suns and 25 C).

  13. Two years of on-orbit gallium arsenide performance from the LIPS solar cell panel experiment

    Science.gov (United States)

    Francis, R. W.; Betz, F. E.

    1985-01-01

    The LIPS on-orbit performance of the gallium arsenide panel experiment was analyzed from flight operation telemetry data. Algorithms were developed to calculate the daily maximum power and associated solar array parameters by two independent methods. The first technique utilizes a least mean square polynomial fit to the power curve obtained with intensity and temperature corrected currents and voltages; whereas, the second incorporates an empirical expression for fill factor based on an open circuit voltage and the calculated series resistance. Maximum power, fill factor, open circuit voltage, short circuit current and series resistance of the solar cell array are examined as a function of flight time. Trends are analyzed with respect to possible mechanisms which may affect successive periods of output power during 2 years of flight operation. Degradation factors responsible for the on-orbit performance characteristics of gallium arsenide are discussed in relation to the calculated solar cell parameters. Performance trends and the potential degradation mechanisms are correlated with existing laboratory and flight data on both gallium arsenide and silicon solar cells for similar environments.

  14. Development of gallium arsenide high-speed, low-power serial parallel interface modules: Executive summary

    Science.gov (United States)

    1988-01-01

    Final report to NASA LeRC on the development of gallium arsenide (GaAS) high-speed, low power serial/parallel interface modules. The report discusses the development and test of a family of 16, 32 and 64 bit parallel to serial and serial to parallel integrated circuits using a self aligned gate MESFET technology developed at the Honeywell Sensors and Signal Processing Laboratory. Lab testing demonstrated 1.3 GHz clock rates at a power of 300 mW. This work was accomplished under contract number NAS3-24676.

  15. Growth of Gold-assisted Gallium Arsenide Nanowires on Silicon Substrates via Molecular Beam Epitaxy

    Directory of Open Access Journals (Sweden)

    Ramon M. delos Santos

    2008-06-01

    Full Text Available Gallium arsenide nanowires were grown on silicon (100 substrates by what is called the vapor-liquid-solid (VLS growth mechanism using a molecular beam epitaxy (MBE system. Good quality nanowires with surface density of approximately 108 nanowires per square centimeter were produced by utilizing gold nanoparticles, with density of 1011 nanoparticles per square centimeter, as catalysts for nanowire growth. X-ray diffraction measurements, scanning electron microscopy, transmission electron microscopy and Raman spectroscopy revealed that the nanowires are epitaxially grown on the silicon substrates, are oriented along the [111] direction and have cubic zincblende structure.

  16. Analytical and experimental procedures for determining propagation characteristics of millimeter-wave gallium arsenide microstrip lines

    Science.gov (United States)

    Romanofsky, Robert R.

    1989-01-01

    In this report, a thorough analytical procedure is developed for evaluating the frequency-dependent loss characteristics and effective permittivity of microstrip lines. The technique is based on the measured reflection coefficient of microstrip resonator pairs. Experimental data, including quality factor Q, effective relative permittivity, and fringing for 50-omega lines on gallium arsenide (GaAs) from 26.5 to 40.0 GHz are presented. The effects of an imperfect open circuit, coupling losses, and loading of the resonant frequency are considered. A cosine-tapered ridge-guide text fixture is described. It was found to be well suited to the device characterization.

  17. THE QUANTUM-WELL STRUCTURES OF SELF ELECTROOPTIC-EFFECT DEVICES AND GALLIUM-ARSENIDE

    Directory of Open Access Journals (Sweden)

    Mustafa TEMİZ

    1996-02-01

    Full Text Available Multiple quantum-well (MQW electroabsorptive self electro optic-effect devices (SEEDs are being extensively studied for use in optical switching and computing. The self electro-optic-effect devices which has quantum-well structures is a new optoelectronic technology with capability to obtain both optical inputs and outputs for Gallium-Arsenide/Aluminum Gallium-Arsenide (GaAs/AlGaAs electronic circuits. The optical inputs and outputs are based on quantum-well absorptive properties. These quantum-well structures consist of many thin layers of semiconductors materials of GaAs/AlGaAs which have emerged some important directions recently. The most important advance in the physics of these materials since the early days has been invention of the heterojunction structures which is based at present on GaAs technology. GaAs/AlGaAs structures present some important advantages to relevant band gap and index of refraction which allow to form the quantum-well structures and also to make semiconductor lasers, dedectors and waveguide optical switches.

  18. Structural and electrooptical characteristics of quantum dots emitting at 1.3 μm on gallium arsenide

    DEFF Research Database (Denmark)

    Fiore, A.; Oesterle, U.; Stanley, R.P.;

    2001-01-01

    We present a comprehensive study of the structural and emission properties of self-assembled InAs quantum dots emitting at 1.3 mum. The dots are grown by molecular beam epitaxy on gallium arsenide substrates. Room-temperature emission at 1.3 mum is obtained by embedding the dots in an InGaAs layer...

  19. Radiation annealing of gallium arsenide implanted with sulphur

    CERN Document Server

    Ardyshev, V M

    2002-01-01

    Sulfur ions were implanted in a semi-insulating GaAs. Photon annealing (805 deg C/(10-12) s) and the thermal one (800 deg C/30 min) were conducted under SiO sub 2 -films coating obtained by different ways. Contents of GaAs components in films were determined from Rutherford backscattering spectra; concentration profiles of electrons were measured by the voltage-capacitance method. Diffusion of sulfur was shown to go in two directions - to the surface and into bulk of GaAs. The first process was induced by vacancies that had been formed near the surface of semiconductors during the dielectric coating. The coefficient of the bulk-diffusion and diffusion-to-surface of sulfur ions under photon annealing was twice as much as that under thermal one. The doping efficiency was also larger

  20. Investigation of spin transport and accumulation in aluminum gallium arsenide

    Science.gov (United States)

    Misuraca, Jennifer

    This dissertation describes spin injection, transport, and detection experiments from Fe electrodes into a bulk AlGaAs channel. This semiconducting alloy is one of a class of persistent photoconductors, chosen as the spin transport medium because its carrier density can be tuned in a controlled manner via photoexcitation through the metal to insulator transition (MIT) in situ. This allows one to determine the dependence of spin lifetime on a variety of external parameters including carrier density, all on one sample. This research represents the first electrical spin-dependent measurements in this material and describes the dependence of the Hanle signal size and spin lifetime on bias, temperature, and carrier density. The photoexcitation needed to change the carrier density in this material comes from an infrared light-emitting diode (IR LED). The first step of this project was to characterize the new, highly Si doped Al0.3Ga 0.7As heterostructures, in order to determine how the illumination of the sample will affect the parameters of the material. To complete this study, Hall crosses were fabricated from the AlGaAs material and the transport properties were measured between 350 mK and 165 K. The resistivity, carrier density, and mobility were determined as a function of temperature for a variety of different illumination times. From this data, the MIT, scattering mechanisms, and the shape of the band tail of the density of states (DOS) were investigated. In fact, this is the first work to electrically probe the DOS in AlGaAs. Once the materials were characterized, they were used to fabricate lateral spin transport devices. Spin transport and accumulation were studied in detail via Hanle effect measurements, which measure the dephasing of electron spins in a perpendicular magnetic field. From these measurements, the spin lifetime of the material can be calculated, and is in the nanosecond range for all measured carrier densities. The spin lifetimes are measured

  1. Straw man trade between multi-junction, gallium arsenide, and silicon solar cells

    Science.gov (United States)

    Gaddy, Edward M.

    1995-01-01

    Multi-junction (MJ), gallium arsenide (GaAs), and silicon (Si) solar cells have respective test efficiencies of approximately 24%, 18.5% and 14.8%. Multi-junction and gallium arsenide solar cells weigh more than silicon solar cells and cost approximately five times as much per unit power at the cell level. A straw man trade is performed for the TRMM spacecraft to determine which of these cell types would have offered an overall performance and price advantage to the spacecraft. A straw man trade is also performed for the multi-junction cells under the assumption that they will cost over ten times that of silicon cells at the cell level. The trade shows that the TRMM project, less the cost of the instrument, ground systems and mission operations, would spend approximately $552 thousand dollars per kilogram to launch and service science in the case of the spacecraft equipped with silicon solar cells. If these cells are changed out for gallium arsenide solar cells, an additional 31 kilograms of science can be launched and serviced at a price of approximately $90 thousand per kilogram. The weight reduction is shown to derive from the smaller area of the array and hence reductions in the weight of the array substrate and supporting structure. If the silicon solar cells are changed out for multi-junction solar cells, an additional 45 kilograms of science above the silicon base line can be launched and serviced at a price of approximately $58 thousand per kilogram. The trade shows that even if the multi-junction arrays are priced over ten times that of silicon cells, a price that is much higher than projected, that the additional 45 kilograms of science are launched and serviced at $182 thousand per kilogram. This is still much less than original $552 thousand per kilogram to launch and service the science. Data and qualitative factors are presented to show that these figures are subject to a great deal of uncertainty. Nonetheless, the benefit of the higher efficiency

  2. Resonance Raman Scattering Studies of Gallium - - Aluminum-Arsenide Superlattices.

    Science.gov (United States)

    Gant, Thomas Andrew

    We have made resonance Raman scattering studies of folded LA phonons and quantized LO phonons in several GaAs-AlAs superlattices. The motivation for this work was to study the electronic structure and the electron -phonon interaction in these structures. The samples were not intentionally doped. The Raman spectra of optic phonons were usually taken at a temperature of 10 K or less. The folded acoustic phonon work was taken at temperatures ranging from 200-300 K in order to enhance the scattering by the thermal factor. Two samples in particular have received very close attention: sample 2292 (50 A GaAs- 20 A AlAs) and sample 3250 (20 A GaAs- 50 A AlAs). In sample 2292 we have made resonance studies of the folded LA phonons and the GaAs -like confined LO_2 mode near the second heavy hole exciton. The results on the folded acoustic phonons show a very strong resonance enhancement for the second order folded phonons, but very little for the first order. An interference between two different scattering channels (the n = 1 light hole and the n = 2 heavy hole subbands) seems to be responsible for this effect. The resonance profile for the LO_2 confined optic phonon in sample 2292 shows 4 peaks in the region from 1.8 eV to 2.05 eV. We have studied the dependence of this resonance profile on the power density. A higher power density was achieved by using the same laser power with a tighter focus. At the higher power density the peak at 1.93 eV (formerly the strongest peak present) vanished. This "bleaching" effect is related to screening due to the higher carrier density. In sample 3250 we have studied the polarization dependence of the resonance profiles of four peaks (LO _2, LO_4, LO_6, and an interface mode) near the lowest direct gap. The A_1 symmetry confined LO modes are seen in both polarized and depolarized geometries, in violation of the usual selection rule (polarized). A mechanism is proposed to explain this result, which has been previously observed by other

  3. Advances in gallium arsenide monolithic microwave integrated-circuit technology for space communications systems

    Science.gov (United States)

    Bhasin, K. B.; Connolly, D. J.

    1986-01-01

    Future communications satellites are likely to use gallium arsenide (GaAs) monolithic microwave integrated-circuit (MMIC) technology in most, if not all, communications payload subsystems. Multiple-scanning-beam antenna systems are expected to use GaAs MMIC's to increase functional capability, to reduce volume, weight, and cost, and to greatly improve system reliability. RF and IF matrix switch technology based on GaAs MMIC's is also being developed for these reasons. MMIC technology, including gigabit-rate GaAs digital integrated circuits, offers substantial advantages in power consumption and weight over silicon technologies for high-throughput, on-board baseband processor systems. In this paper, current developments in GaAs MMIC technology are described, and the status and prospects of the technology are assessed.

  4. Outdoor Performance of a Thin-Film Gallium-Arsenide Photovoltaic Module

    Energy Technology Data Exchange (ETDEWEB)

    Silverman, T. J.; Deceglie, M. G.; Marion, B.; Cowley, S.; Kayes, B.; Kurtz, S.

    2013-06-01

    We deployed a 855 cm2 thin-film, single-junction gallium arsenide (GaAs) photovoltaic (PV) module outdoors. Due to its fundamentally different cell technology compared to silicon (Si), the module responds differently to outdoor conditions. On average during the test, the GaAs module produced more power when its temperature was higher. We show that its maximum-power temperature coefficient, while actually negative, is several times smaller in magnitude than that of a Si module used for comparison. The positive correlation of power with temperature in GaAs is due to temperature-correlated changes in the incident spectrum. We show that a simple correction based on precipitable water vapor (PWV) brings the photocurrent temperature coefficient into agreement with that measured by other methods and predicted by theory. The low operating temperature and small temperature coefficient of GaAs give it an energy production advantage in warm weather.

  5. Point defects and electric compensation in gallium arsenide single crystals; Punktdefekte und elektrische Kompensation in Galliumarsenid-Einkristallen

    Energy Technology Data Exchange (ETDEWEB)

    Kretzer, Ulrich

    2007-12-10

    In the present thesis the point-defect budget of gallium arsenide single crystals with different dopings is studied. It is shown, in which way the concentration of the single point defects depende on the concentration of the dopants, the stoichiometry deviation, and the position of the Fermi level. For this serve the results of the measurement-technical characterization of a large number of samples, in the fabrication of which these parameters were directedly varied. The main topic of this thesis lies in the development of models, which allow a quantitative description of the experimentally studied electrical and optical properties of gallium arsenide single crystals starting from the point-defect concentrations. Because from point defects charge carriers can be set free, their concentration determines essentially the charge-carrier concentration in the bands. In the ionized state point defects act as scattering centers for free charge carriers and influence by this the drift mobility of the charge carriers. A thermodynamic modeling of the point-defect formation yields statements on the equilibrium concentrations of the point defects in dependence on dopant concentration and stoichiometry deviation. It is show that the electrical properties of the crystals observed at room temperature result from the kinetic suppression of processes, via which the adjustment of a thermodynamic equilibrium between the point defects is mediated. [German] In der vorliegenden Arbeit wird der Punktdefekthaushalt von Galliumarsenid-Einkristallen mit unterschiedlichen Dotierungen untersucht. Es wird gezeigt, in welcher Weise die Konzentration der einzelnen Punktdefekte von der Konzentration der Dotierstoffe, der Stoechiometrieabweichung und der Lage des Ferminiveaus abhaengen. Dazu dienen die Ergebnisse der messtechnischen Charakterisierung einer grossen Anzahl von Proben, bei deren Herstellung diese Parameter gezielt variiert wurden. Der Schwerpunkt der Arbeit liegt in der Entwicklung

  6. Barium iron arsenide, barium cobalt arsenide, barium nickel arsenide single crystals and superconductivity upon cobalt doping

    Energy Technology Data Exchange (ETDEWEB)

    Ronning, Filip [Los Alamos National Laboratory; Sefat, A S [ORNL; Mcguire, M M [ORNL; Sales, B [ORNL; Jin, R [ORNL; Mandrus, D [ORNL

    2009-01-01

    The crystal structure and physical properties of BaFe{sub 2}As{sub 2}, BaCo{sub 2}As{sub 2}, and BaNi{sub 2}As{sub 2} single crystals are surveyed. BaFe{sub 2}As{sub 2} gives a magnetic and structural transition at T{sub N} = 132(1) K, BaCo{sub 2}As{sub 2} is a paramagnetic metal, while BaNi{sub 2}As{sub 2} has a structural phase transition at T{sub 0} = 131 K, followed by superconductivity below {Tc} = 0.69 K. The bulk superconductivity in Co-doped BaFe{sub 2}As{sub 2} below {Tc} = 22 K is demonstrated by resistivity, magnetic susceptibility, and specific heat data. In contrast to the cuprates, the Fe-based system appears to tolerate considerable disorder in the transition metal layers. First principles calculations for BaFe{sub 1.84}Co{sub 0.16}As{sub 2} inter-band scattering due to Co is weak.

  7. Highly ordered horizontal indium gallium arsenide/indium phosphide multi-quantum-well in wire structure on (001) silicon substrates

    Science.gov (United States)

    Han, Yu; Li, Qiang; Lau, Kei May

    2016-12-01

    We report the characteristics of indium gallium arsenide stacked quantum structures inside planar indium phosphide nanowires grown on exact (001) silicon substrates. The morphological evolution of the indium phosphide ridge buffers inside sub-micron trenches has been studied, and the role of inter-facet diffusion in this process is discussed. Inside a single indium phosphide nanowire, we are able to stack quantum structures including indium gallium arsenide flat quantum wells, quasi-quantum wires, quantum wires, and ridge quantum wells. Room temperature photoluminescence measurements reveal a broadband emission spectrum centered at 1550 nm. Power dependent photoluminescence analysis indicates the presence of quasi-continuum states. This work thus provides insights into the design and growth process control of multiple quantum wells in wire structures for high performance nanowire lasers on a silicon substrate with 1550 nm band emission.

  8. Gallium self-diffusion in gallium arsenide: A study using isotope heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lei; Hsu, L.; Haller, E.E. [California Univ., Berkeley, CA (United States)]|[Lawrence Berkeley National Lab., CA (United States); Erickson, J.W. [Evans (Charles) and Associates, Redwood City, CA (United States); Fischer, A.; Eberl, K.; Cardona, M. [Max-Planck-Institut, Stuttgart (Germany)

    1996-09-01

    Ga self-diffusion was studied with secondary-ion mass spectroscopy in {sup 69}GaAs/{sup 71}GaAs isotope heterostructures grown by molecular beam epitaxy on GaAs substrates. Results show that the Ga self- diffusion coefficient in intrinsic GaAs can be described accurately with D = (43{+-}25 cm{sup 2}s{sup -1})exp(-4.24{+-}0.06 eV/k{sub B}T) over 6 orders of magnitude between 800 and 1225 C under As-rich condition. Experimental results combined with theoretical calculations strongly suggest Ga vacancy being the dominant native defect controlling the diffusion. No significant doping effects were observed in samples where the substrates were doped with Te up to 4x10{sup 17}cm{sup -3} or Zn up to 1x10{sup 19}cm{sup -3}.

  9. Modelling of the small pixel effect in gallium arsenide X-ray imaging detectors

    CERN Document Server

    Sellin, P J

    1999-01-01

    A Monte Carlo simulation has been carried out to investigate the small pixel effect in highly pixellated X-ray imaging detectors fabricated from semi-insulating gallium arsenide. The presence of highly non-uniform weighting fields in detectors with a small pixel geometry causes the majority of the induced signal to be generated when the moving charges are close to the pixellated contacts. The response of GaAs X-ray imaging detectors is further complicated by the presence of charge trapping, particularly of electrons. In this work detectors are modelled with a pixel pitch of 40 and 150 mu m, and with thicknesses of 300 and 500 mu m. Pulses induced in devices with 40 mu m pixels are due almost totally to the movement of the lightly-trapped holes and can exhibit significantly higher charge collection efficiencies than detectors with large electrodes, in which electron trapping is significant. Details of the charge collection efficiencies as a function of interaction depth in the detector and of the incident phot...

  10. Theory, design, and simulation of GASP: A block data flow architecture for gallium arsenide supercomputers

    Energy Technology Data Exchange (ETDEWEB)

    Fouts, D.J.

    1990-01-01

    The advantages and disadvantages of using high-speed gallium arsenide (GaAs) logic for implementing digital systems are reviewed. A set of design guidelines is presented for systems that will be constructed with high-speed technologies such as GaAs and silicon emitter coupled logic (ECL). A new class of computer and digital system architectures, known as functionally modular architectures, is defined and explained. Functionally modular architectures are ideal for implementation in GaAs because they adhere to the design guidelines. GASP, a new, functionally modular, block data flow computer architecture is then described. SPICE simulations indicate that if constructed with existing GaAs IC technology, parts of GASP could run at a clock speed of 1 GHz, with the rest of the architecture using a 500 MHz clock. The new architecture uses data flow techniques at a program block level, which allows efficient execution of parallel programs while maintaining reasonably good performance on sequential programs. A simulation study of the architecture's best case and worst case performance is presented. Simulations of GASP executing a highly parallel program indicate that an instruction execution rate of over 30,000 MIPS can be attained with a 65 processor system.

  11. Fabrication and applications of orientation-patterned gallium arsenide for mid-infrared generation

    Energy Technology Data Exchange (ETDEWEB)

    Grisard, A.; Gutty, F.; Lallier, E. [Thales Research and Technology France, 1 av. Augustin Fresnel, 91767 Palaiseau Cedex (France); Gerard, B. [III-V Lab, 1 av. Augustin Fresnel, 91767 Palaiseau Cedex (France); Jimenez, J. [GdS Optronlab, Fisica Materia Condensada, Universidad de Valladolid, 47011 Valladolid (Spain)

    2012-07-15

    Nonlinear optical materials play a key role in the development of coherent sources of radiation, by frequency conversion of light from other light sources, e.g. diode, solid-state, and fiber lasers, into spectral ranges where few lasers exist or perform poorly. Based on the principle of the quasi-phase matching, the design and fabrication of orientation-patterned Gallium Arsenide crystals (OP-GaAs) has recently led to demonstrations of second harmonic generation, optical parametric generation, amplification and oscillation from 1 to 12 {mu}m. The most efficient fabrication route for these crystals relies on the use of the near-equilibrium growth process HVPE (Hydride Vapour Phase Epitaxy), by orientation-selective regrowth on OP-GaAs template wafers with a thickness suited to bulk nonlinear optics. This work deals with recent characterizations based on optical experiments and cathodoluminescence measurements, targeting the identification of the main defects, their spatial distribution, and their relation to the optical propagation losses. Latest improvements of the HVPE growth step have enabled to reach an unprecedented level of losses, below 0.016 cm{sup -1}, and a large range of available QPM periods and thickness of structures (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. Transport-reaction model for defect and carrier behavior within displacement cascades in gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Wampler, William R.; Myers, Samuel Maxwell,

    2014-02-01

    A model is presented for recombination of charge carriers at displacement damage in gallium arsenide, which includes clustering of the defects in atomic displacement cascades produced by neutron or ion irradiation. The carrier recombination model is based on an atomistic description of capture and emission of carriers by the defects with time evolution resulting from the migration and reaction of the defects. The physics and equations on which the model is based are presented, along with details of the numerical methods used for their solution. The model uses a continuum description of diffusion, field-drift and reaction of carriers and defects within a representative spherically symmetric cluster. The initial radial defect profiles within the cluster were chosen through pair-correlation-function analysis of the spatial distribution of defects obtained from the binary-collision code MARLOWE, using recoil energies for fission neutrons. Charging of the defects can produce high electric fields within the cluster which may influence transport and reaction of carriers and defects, and which may enhance carrier recombination through band-to-trap tunneling. Properties of the defects are discussed and values for their parameters are given, many of which were obtained from density functional theory. The model provides a basis for predicting the transient response of III-V heterojunction bipolar transistors to pulsed neutron irradiation.

  13. Evaluation of a gallium arsenide solar panel on the LIPS II satellite

    Energy Technology Data Exchange (ETDEWEB)

    Trumble, T.M.; Betz, F.

    1984-05-01

    On 10 February 1983 the Living Plume Shield (LIPS II) satellite was launched by the Naval Research Laboratory with three double sided solar panels providing electrical power. One side of one panel contains 300 2cm X 2cm gallium arsenide (GaAs) solar cells while each of the other five sides contain 104 2.1cm X 6.2cm silicon (Si) solar cells. The U.S. Air Force developed GaAs cells were provided to the Navy in a cooperative program to build, test, qualify and fly a GaAs solar panel. Nineteen months after the beginning of the cooperative program the vehicle was launched. There are considerable statistical variances in the data and data cannot be acquired continuously owing to the requirement to be over a tracking station while the GaAs panel is facing the sun. The first 30 days of operation were unmeasured due to satellite orientation problems. The first measurements indicated a 7.3% power loss in panel performance compared to ground preflight measurements. This loss is still unexplained. This paper provides a summary of the LIPS II program and the data analysis on the GaAs solar panel performance for the first year in orbit.

  14. Monopole Charge Domain in High-Gain Gallium Arsenide Photoconductive Switches

    Institute of Scientific and Technical Information of China (English)

    施卫; 陈二柱; 张显斌; 李琦

    2002-01-01

    Considering that semi-insulating gallium arsenide photoconductive switches can be triggered into the high gain mode and no reliable theories can account for the observed transient characteristics, we propose the monopole charge domain model to explain the peculiar switching phenomena occurring in the high gain mode and we discuss the requirements for the lock-on switching. During operation on this mode, the applied field across the switch and the lock-on field are all larger than the Gunn threshold field. Our developed monopole charge domain is based on the transferred-electron effect, but the domain is only composed of large numbers of electrons piled up due to the negative differential mobility. Using the model and taking the physical mechanism of the avalanche impact ionization and recombination radiation into consideration, we interpret the typical phenomena of the lock-on effect, such as the time delay between the beginning of optical illumination and turning-on of the switch, and the conduction mechanism of the sustaining phase. Under different conditions of bias field intensity and incident light energy, the time delay of the switching is calculated. The results show that the physical mechanisms of impact ionization and recombination radiation occurring in the monopole charge domain are responsible for the lock-on switching.

  15. Specific features of the formation of dislocation structure in gallium arsenide single crystals obtained by the Czochralski method

    Science.gov (United States)

    Parfenteva, I. B.; Pugachev, B. V.; Pavlov, V. F.; Kozlova, Yu. P.; Knyazev, C. N.; Yugova, T. G.

    2017-03-01

    The influence of the deviation of seed orientation from the [100] direction on the formation of a dislocation structure of gallium arsenide single crystals grown by the Czochralski method has been revealed. The intensive multiplication of dislocations and formation of a block structure occur at deviation by an angle of more than 3° in the region that is radially shifted to one of crystal sides. The linear density of dislocations in the walls changes from 1 × 104 cm-1 in low-angle boundaries to 6 × 104 cm-1 in subboundaries.

  16. Development of devices and systems of growth of gallium arsenide ingots for micro, nano electronics and photovoltaics

    Directory of Open Access Journals (Sweden)

    A. P. Oksanich

    2013-09-01

    Full Text Available Gallium arsenide is a perspective semiconductor, the need for which is constantly increasing. This is associated with the development of electronic components operating in excess of the high frequency range and development of terrestrial photovoltaics based on gallium arsenide solar cells. Increase in diameter of grown ingots leads to a deterioration in their performance, which is caused by the imperfection of growing technology. The paper presents the results of the development of systems and devices which help to improve existing technology to produce GaAs ingots and wafers with a diameter of 100 mm with the best technical parameters. Developed a system to manage growing GaAs ingot. As a sensor of diameter ingot it uses a weighting method provides a measurement error in the process of growing ± 1,0 mm. The system allows to grow GaAs ingots with an error of ± 2 mm. For the formation of temperature gradients developed thermal unit, which provides a gradient of 51 .. 53 K cm in growing of ingots with diameter of 100 mm. For adjusting the process parameters were developed measuring device of the internal stresses that are generated in the ingot during the growth of the GaAs ingot. Presented in paper technical solutions provided a silicon ingot with a diameter of 100 mm. with mobility, cm2 V-1 s-1 - 2500 ÷ 3500, the charge carrier density, cm-3 - 5x1017 ÷ 5x1018; dislocation density, cm-2 - to 8x104.

  17. Cascaded Orientation-Patterned Gallium Arsenide Optical Parametric Oscillator for Improved Longwave Infrared Conversion Efficiency

    Science.gov (United States)

    Feaver, Ryan K.

    Optical parametric oscillators (OPOs) utilizing quasi-phase matched materials offer an appealing alternative to direct laser sources. Quasi-phase matched materials provide a useful alternative to traditional birefringent nonlinear optical materials and through material engineering, higher nonlinear coefficients can now be accessed. Orientation patterned gallium arsenide (OPGaAs) is an ideal material because of its broad IR transmission and large nonlinear coefficient. In contrast to ferroelectric materials, such as lithium niobate, where the pattern is fabricated through electric poling, zincblende materials, like OPGaAs, are grown epitaxially with the designed pattern. Generating longwave output from a much shorter pump wavelength, however, is relatively inefficiency due to the large quantum defect when compared to similar devices operating in the 3 - 5 mum regime. One method to increase pump to idler conversion efficiency is to recycle the undesired and higher energy signal photons into additional idler photons via a second nonlinear stage. An external amplifier stage can be utilized, where the signal and idler from the OPO are sent to a second nonlinear crystal in which the idler is amplified at the expense of the signal. Alternatively, the second crystal can be placed within the original OPO cavity where the signal from the first-stage acts as the pump for the second crystal and the resonant intensity of the signal is higher. Pumping the second crystal within the OPO should lead to higher conversion efficiency into the longwave idler. The grating period needed for the second crystal to use the signal from the first crystal to produce additional idler has the fortuitous advantage that it will not phase match to the original pump wavelength, avoiding unwanted nonlinear interactions. Therefore, a simple linear cavity can be utilized where the pump from the first-stage will simply propagate through the second crystal without undesired results. Without this feature

  18. Spectroscopy of titanium-doped gallium lanthanum sulfide glass

    OpenAIRE

    2008-01-01

    Titanium-doped gallium lanthanum sulfide (Ti:GLS) and gallium lanthanum oxysulfide (Ti:GLSO) glasses have an absorption band at similar to 500-600 nm that cannot be fully resolved because of its proximity to the band edge of the glass. At concentrations >0.5% a shoulder at 980 nm is observed in Ti:GLS but not in Ti :GLSO. The emission spectra of Ti:GLS and T :GLSO both peak at 900 nm with lifetimes of 67 and 97)us, respectively. We propose that the absorption at similar to 600 nm is due to th...

  19. Acoustic Phonon Scattering in Modulation Doped Aluminum sub x Gallium sub (1-x) Arsenide/Gallium Arsenide Heterojunctions

    Science.gov (United States)

    1988-07-01

    of the distribution function through Monte Carlo simula- • tions of a two-dimensional electron gas in an AlxGaj-xAs/GaAs heterostructure confirm this...shown in Fig. 4.1b). The broadening may be regarded somewhat imprecisely as arising from the Heisenberg uncertainty principle, ,Er t, where AE is a...significant energy dependence of the den- ,,. sity of states. From the Heisenberg uncertainty principle we see that the broadening of the Landau levels

  20. Radiant Power Degradation of Silicon-Doped Gallium Arsenide and Gallium Aluminum Arsenide Infrared Light-Emitting Diodes.

    Science.gov (United States)

    1987-05-01

    measured using a United Detector Technology Model 61AC (UDT61AC) Optometer , a United Detector Technol- ogy Model 2575R (UDT2575R) Integrating Sphere...the opening of the integrating sphere. Be sure both the integrating sphere and the diode are stationary. 3. Check the optometer . Be sure the CH 1...to 10-2. (You have now compensated the optometer for ambient light). The display may still read something on the 10-2 MULTIPLIER setting. If it does

  1. Gallium arsenide exposure impairs processing of particulate antigen by macrophages: modification of the antigen reverses the functional defect.

    Science.gov (United States)

    Hartmann, Constance B; McCoy, Kathleen L

    2004-06-11

    Gallium arsenide (GaAs), a semiconductor used in the electronics industry, causes systemic immunosuppression in animals. The chemical's impact on macrophages to process the particulate antigen, sheep red blood cells (SRBC), for a T cell response in culture was examined after in vivo exposure of mice. GaAs-exposed splenic macrophages were defective in activating SRBC-primed lymph node T cells that could not be attributed to impaired phagocytosis. Modified forms of SRBC were generated to examine the compromised function of GaAs-exposed macrophages. SRBC were fixed to maintain their particulate nature and subsequently delipidated with detergent. Delipidation of intact SRBC was insufficient to restore normal antigen processing in GaAs-exposed macrophages. However, chemically exposed cells efficiently processed soluble sheep proteins. These findings suggest that the problem may lie in the release of sequestered sheep protein antigens, which then could be effectively cleaved to peptides. Furthermore, opsonization of SRBC with IgG compensated for the macrophage processing defect. The influence of signal transduction and phagocytosis via Fcgamma receptors on improved antigen processing could be dissociated. Immobilized anti-Fcgamma receptor antibody activated macrophages to secrete a chemokine, but did not enhance processing of unmodified SRBC by GaAs-exposed macrophages. Restoration of normal processing of particulate SRBC by chemically exposed macrophages involved phagocytosis through Fcgamma receptors. Hence, initial immune responses may be very sensitive to GaAs exposure, and the chemical's immunosuppression may be averted by opsonized particulate antigens.

  2. Development of a unique laboratory standard: Indium gallium arsenide detector for the 500-1700 nm spectral region

    Science.gov (United States)

    1987-01-01

    A planar (5 mm diameter) indium gallium arsenide detector having a high (greater than 50 pct) quantum efficiency from the visible into the infrared spectrum (500 to 1700 nm) was fabricated. Quantum efficiencies as high as 37 pct at 510 nm, 58 pct at 820 nm and 62 pct at 1300 nm and 1550 nm were measured. A planar InP/InGaAs detector structure was also fabricated using vapor phase epitaxy to grow device structures with 0, 0.2, 0.4 and 0.6 micrometer thick InP caps. Quantum efficiency was studied as a function of cap thickness. Conventional detector structures were also used by completely etching off the InP cap after zinc diffusion. Calibrated quantum efficiencies were measured. Best results were obtained with devices whose caps were completely removed by etching. Certain problems still remain with these detectors including non-uniform shunt resistance, reproducibility, contact resistance and narrow band anti-reflection coatings.

  3. A novel three-jet microreactor for localized metal-organic chemical vapour deposition of gallium arsenide: design and simulation

    Science.gov (United States)

    Konakov, S. A.; Krzhizhanovskaya, V. V.

    2016-08-01

    We present a novel three-jet microreactor design for localized deposition of gallium arsenide (GaAs) by low-pressure Metal-Organic Chemical Vapour Deposition (MOCVD) for semiconductor devices, microelectronics and solar cells. Our approach is advantageous compared to the standard lithography and etching technology, since it preserves the nanostructure of the deposited material, it is less time-consuming and less expensive. We designed two versions of reactor geometry with a 10-micron central microchannel for precursor supply and with two side jets of a dilutant to control the deposition area. To aid future experiments, we performed computational modeling of a simplified-geometry (twodimensional axisymmetric) microreactor, based on Navier-Stokes equations for a laminar flow of chemically reacting gas mixture of Ga(CH3)3-AsH3-H2. Simulation results show that we can achieve a high-rate deposition (over 0.3 μm/min) on a small area (less than 30 μm diameter). This technology can be used in material production for microelectronics, optoelectronics, photovoltaics, solar cells, etc.

  4. A final report for Gallium arsenide P-I-N detectors for high-sensitivity imaging of thermal neutrons

    CERN Document Server

    Vernon, S M

    1999-01-01

    This SBIR Phase I developed neutron detectors made FR-om gallium arsenide (GaAs) p-type/ intrinsic/n-type (P-I-N) diodes grown by metalorganic chemical vapor deposition (MOCVD) onto semi-insulating (S1) bulk GaAs wafers. A layer of isotonically enriched boron-10 evaporated onto the FR-ont surface serves to convert incoming neutrons into lithium ions and a 1.47 MeV alpha particle which creates electron-hole pairs that are detected by the GaAs diode. Various thicknesses of ''intrinsic'' (I) undoped GaAs were tested, as was use of a back-surface field (BSF) formed FR-om a layer of Al sub x Ga sub 1 sub - sub x As. Schottky-barrier diodes formed FR-om the same structures without the p+ GaAs top layer were tested as a comparison. After mesa etching and application of contacts, devices were tested in visible light before application of the boron coating. Internal quantum efficiency (IQE) of the best diode near the GaAs bandedge is over 90%. The lowest dark current measured is 1 x 10 sup - sup 1 sup 2 amps at -1 V o...

  5. Electronic transport properties of graphene doped by gallium

    Science.gov (United States)

    Mach, J.; Procházka, P.; Bartošík, M.; Nezval, D.; Piastek, J.; Hulva, J.; Švarc, V.; Konečný, M.; Kormoš, L.; Šikola, T.

    2017-10-01

    In this work we present the effect of low dose gallium (Ga) deposition (graphene grown by chemical vapor deposition. In situ graphene transport measurements performed with a graphene field-effect transistor structure show that at low Ga coverages a graphene layer tends to be strongly n-doped with an efficiency of 0.64 electrons per one Ga atom, while the further deposition and Ga cluster formation results in removing electrons from graphene (less n-doping). The experimental results are supported by the density functional theory calculations and explained as a consequence of distinct interaction between graphene and Ga atoms in case of individual atoms, layers, or clusters.

  6. Thermal Stability and Spectroscopic Properties of Yb3+-Doped New Gallium-Lead-Germanate Glass

    Institute of Scientific and Technical Information of China (English)

    XU Shi-Qing; FENG Ai-Ming; ZHANG Li-Yan; ZHAO Shi-Long; WANG Bao-Ling; ZHANG Jue; WANG Wei; BAO Ren-Qiang

    2006-01-01

    @@ Yb3+-doped new gallium-lead-germanate glass is presented. Thermal stability, spectroscopic and laser performance parameters of the Yb3+-doped new gallium-lead-germanate glass are calculated. The results show that the Yb3+-doped new gallium-lead-germanate glass has good thermal stability (△T = 198 ℃), high stimulated emission cross section (0.79pm2), and long fluorescence lifetime (1.46ms). Compared with other Yb3+-doped glass hosts, the Yb3+-doped new gallium-lead-germanate glass has better laser performance parameters and laser properties, indicating that Yb3+-doped new gallium-lead-germanate glass is a promising laser material for short pulse generation in diode pumped lasers, short pulse generation tunable laser, high-peak power and high-average power lasers.

  7. Electronic structure, magnetic and superconducting properties of co-doped iron-arsenide superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Rosner, Helge; Schnelle, Walter; Nicklas, Michael; Leithe-Jasper, Andreas [MPI CPfS Dresden (Germany); Weikert, Franziska [Los Alamos National Laboratory, New Mexico (United States); HLD Dresden Rossendorf (Germany); Wosnitza, Joachim [HLD Dresden Rossendorf (Germany)

    2013-07-01

    We present a joint experimental and theoretical study of co-doped iron-arsenide superconductors of the 122 family A{sub 1-x}K{sub x}Fe{sub 2-y}T{sub y}As{sub 2} (A = Ba,Sr,Eu; T = Co,Ru,Rh). In these systems, the co-doping enables the separation of different parameters - like electron count, disorder or the specific geometry of the FeAs layer - with respect to the position of the respective compounds in the general 122 phase diagram. For a series of compounds, we investigate the relevance of the different parameters for the magnetic, thermodynamic and superconducting properties. Our experimental investigations are supported by density functional electronic structure calculations applying different approximations for doping and disorder.

  8. Improvement of radiation stability of semi-insulating gallium arsenide crystals by deposition of diamond-like carbon films

    Science.gov (United States)

    Klyui, N. I.; Lozinskii, V. B.; Liptuga, A. I.; Izotov, V. Yu.; Han, Wei; Liu, Bingbing

    2016-12-01

    We studied the properties of optical elements for the IR spectral range based on semi-insulating gallium arsenide (SI-GaAs) and antireflecting diamond-like carbon films (DLCF). Particular attention has been paid to the effect of penetrating γ-radiation on transmission of the developed optical elements. A Co60 source and step-by-step gaining of γ-irradiation dose were used for treatment of both an initial SI-GaAs crystal and DLCF/SI-GaAs structures. It was shown that DLCF deposition essentially increases degradation resistance of the SI-GaAs-based optical elements to γ-radiation. Particularly, the transmittance of the DLCF/SI-GaAs structure after γ-irradiation with a dose 9ṡ104 Gy even exceeds that of initial structures. The possible mechanism that explains the effect of γ-radiation on the SI-GaAs crystals and the DLCF/SI-GaAs structures at different irradiation doses was proposed. The effect of small doses is responsible for non-monotonic transmission changes in both SI-GaAs crystals and DLCF/SI-GaAs structures. At further increasing the γ-irradiation dose, the variation of properties of both DLCF and SI-GaAs crystal influences on the transmission of DLCF/SI-GaAs system. At high γ-irradiation dose 1.4ṡ105 Gy, passivation of radiation defects in the SI-GaAs bulk by hydrogen diffused from DLCF leads to increasing the degradation resistance of the SI-GaAs crystals coated with DLCF as compared with the crystals without DLCF.

  9. Analysis of gallium arsenide deposition in a horizontal chemical vapor deposition reactor using massively parallel computations

    Energy Technology Data Exchange (ETDEWEB)

    Salinger, A.G.; Shadid, J.N.; Hutchinson, S.A. [and others

    1998-01-01

    A numerical analysis of the deposition of gallium from trimethylgallium (TMG) and arsine in a horizontal CVD reactor with tilted susceptor and a three inch diameter rotating substrate is performed. The three-dimensional model includes complete coupling between fluid mechanics, heat transfer, and species transport, and is solved using an unstructured finite element discretization on a massively parallel computer. The effects of three operating parameters (the disk rotation rate, inlet TMG fraction, and inlet velocity) and two design parameters (the tilt angle of the reactor base and the reactor width) on the growth rate and uniformity are presented. The nonlinear dependence of the growth rate uniformity on the key operating parameters is discussed in detail. Efficient and robust algorithms for massively parallel reacting flow simulations, as incorporated into our analysis code MPSalsa, make detailed analysis of this complicated system feasible.

  10. Spectroscopy of vanadium (III) doped gallium lanthanum sulphide chalcogenide glass

    CERN Document Server

    Hughes, M; Rutt, H; Hewak, D

    2014-01-01

    Vanadium doped gallium lanthanum sulphide glass (V:GLS) displays three absorption bands at 580, 730 and 1155 nm identified by photoluminescence excitation measurements. Broad photoluminescence, with a full width half maximum (FWHM) of 500 nm, is observed peaking at 1500 nm when exciting at 514, 808 and 1064 nm. The fluorescence lifetime and quantum efficiency at 300 K were measured to be 33.4 us and 4 % respectively. From the available spectroscopic data we propose the vanadium ions valence to be 3+ and be in tetrahedral coordination The results indicate potential for development of a laser or optical amplifier based on V:GLS.

  11. Infrared emission from holmium doped gallium lanthanum sulphide glass

    Science.gov (United States)

    Schweizer, T.; Samson, B. N.; Hector, J. R.; Brocklesby, W. S.; Hewak, D. W.; Payne, D. N.

    1999-08-01

    Infrared emission at 1.2, 1.25, 1.67, 2.0, 2.2, 2.9, 3.9, and 4.9 μm is measured in holmium (Ho 3+) doped gallium lanthanum sulphide (GLS) glass. Branching ratios, radiative quantum efficiencies, and emission cross-sections are calculated from lifetime, absorption, and emission measurements using Judd-Ofelt analysis and the Füchtbauer-Ladenburg equation. The fluorescence band at 3.9 μm coincides with an atmospheric transmission window and the fluorescence band at 4.9 μm overlaps with the fundamental absorption of carbon monoxide, making the glass a potential fibre laser source for remote sensing and gas sensing applications. This is the first time this latter transition has been reported in any holmium doped host.

  12. Wet chemical functionalization of III-V semiconductor surfaces: alkylation of gallium arsenide and gallium nitride by a Grignard reaction sequence.

    Science.gov (United States)

    Peczonczyk, Sabrina L; Mukherjee, Jhindan; Carim, Azhar I; Maldonado, Stephen

    2012-03-13

    Crystalline gallium arsenide (GaAs) (111)A and gallium nitride (GaN) (0001) surfaces have been functionalized with alkyl groups via a sequential wet chemical chlorine activation, Grignard reaction process. For GaAs(111)A, etching in HCl in diethyl ether effected both oxide removal and surface-bound Cl. X-ray photoelectron (XP) spectra demonstrated selective surface chlorination after exposure to 2 M HCl in diethyl ether for freshly etched GaAs(111)A but not GaAs(111)B surfaces. GaN(0001) surfaces exposed to PCl(5) in chlorobenzene showed reproducible XP spectroscopic evidence for Cl-termination. The Cl-activated GaAs(111)A and GaN(0001) surfaces were both reactive toward alkyl Grignard reagents, with pronounced decreases in detectable Cl signal as measured by XP spectroscopy. Sessile contact angle measurements between water and GaAs(111)A interfaces after various levels of treatment showed that GaAs(111)A surfaces became significantly more hydrophobic following reaction with C(n)H(2n-1)MgCl (n = 1, 2, 4, 8, 14, 18). High-resolution As 3d XP spectra taken at various times during prolonged direct exposure to ambient lab air indicated that the resistance of GaAs(111)A to surface oxidation was greatly enhanced after reaction with Grignard reagents. GaAs(111)A surfaces terminated with C(18)H(37) groups were also used in Schottky heterojunctions with Hg. These heterojunctions exhibited better stability over repeated cycling than heterojunctions based on GaAs(111)A modified with C(18)H(37)S groups. Raman spectra were separately collected that suggested electronic passivation by surficial Ga-C bonds at GaAs(111)A. Specifically, GaAs(111)A surfaces reacted with alkyl Grignard reagents exhibited Raman signatures comparable to those of samples treated with 10% Na(2)S in tert-butanol. For GaN(0001), high-resolution C 1s spectra exhibited the characteristic low binding energy shoulder demonstrative of surface Ga-C bonds following reaction with CH(3)MgCl. In addition, 4

  13. Drift velocity oscillations in n-gallium arsenide at 77/sup 0/K

    Energy Technology Data Exchange (ETDEWEB)

    Matulionis, A.; Pozela, J.; Reklaitis, A.

    1975-01-01

    Electron relaxation after an instantaneous application of dc electric fields ranging from 10 V/cm to 1 kV/cm was studied numerically by a many-particle Monte Carlo method. The model takes into account polar optical, acoustic, and impurity scattering in the nonparabolic central valley. In the limited range of doping, electric field, and temperature the electron mean energy and drift velocity oscillate. The oscillation frequency is nearly proportional to the applied electric field (approximately 35 GHz at 60 V/cm). The oscillations are associated with a shuttle-type electron motion in the Debye sphere of k-space; they are not heavily damped if the electron runaway is favored inside and restrained outside the Debye sphere. (WDM)

  14. Gallium Arsenide detectors for X-ray and electron (beta particle) spectroscopy

    Science.gov (United States)

    Lioliou, G.; Barnett, A. M.

    2016-11-01

    Results characterizing GaAs p+-i-n+ mesa photodiodes with a 10 μm i layer for their spectral response under illumination of X-rays and beta particles are presented. A total of 22 devices, having diameters of 200 μm and 400 μm, were electrically characterized at room temperature. All devices showed comparable characteristics with a measured leakage current ranging from 4 nA/cm2 to 67 nA/cm2 at an internal electric field of 50 kV/cm. Their unintentionally doped i layers were found to be almost fully depleted at 0 V due to their low doping density. 55Fe X-ray spectra were obtained using one 200 μm diameter device and one 400 μm diameter device. The best energy resolution (FWHM at 5.9 keV) achieved was 625 eV using the 200 μm and 740 eV using the 400 μm diameter device, respectively. Noise analysis showed that the limiting factor for the energy resolution of the system was the dielectric noise; if this noise was eliminated by better design of the front end of the readout electronics, the achievable resolution would be 250 eV. 63Ni beta particle spectra obtained using the 200 μm diameter device showed the potential utility of these detectors for electron and beta particle detection. The development of semiconductor electron spectrometers is important particularly for space plasma physics; such devices may find use in future space missions to study the plasma environment of Jupiter and Europa and the predicted electron impact excitation of water vapor plumes from Europa hypothesized as a result of recent Hubble Space Telescope (HST) UV observations.

  15. Spin-phonon coupling in scandium doped gallium ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, Keka R., E-mail: kekarc@barc.gov.in, E-mail: smyusuf@barc.gov.in; Mukadam, M. D.; Basu, S.; Yusuf, S. M., E-mail: kekarc@barc.gov.in, E-mail: smyusuf@barc.gov.in [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Paul, Barnita; Roy, Anushree [Department of Physics, Indian Institute of Technology, Kharagpur 721302 (India); Grover, Vinita; Tyagi, A. K. [Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2015-03-28

    We embarked on a study of Scandium (Sc) doped (onto Ga site) gallium ferrite (GaFeO{sub 3}) and found remarkable magnetic properties. In both doped as well as parent compounds, there were three types of Fe{sup 3+} ions (depending on the symmetry) with the structure conforming to space group Pna2{sub 1} (Sp. Grp. No. 33) below room temperature down to 5 K. We also found that all Fe{sup 3+} ions occupy octahedral sites, and carry high spin moment. For the higher Sc substituted sample (Ga{sub 1−x}Sc{sub x}FeO{sub 3}: x = 0.3), a canted magnetic ordered state is found. Spin-phonon coupling below Néel temperature was observed in doped compounds. Our results indicated that Sc doping in octahedral site modifies spin-phonon interactions of the parent compound. The spin-phonon coupling strength was estimated for the first time in these Sc substituted compounds.

  16. Ion implantation of silicon in gallium arsenide: Damage and annealing characterizations

    Science.gov (United States)

    Pribat, D.; Dieumegard, D.; Croset, M.; Cohen, C.; Nipoti, R.; Siejka, J.; Bentini, G. G.; Correra, L.; Servidori, M.

    1983-05-01

    The purpose of this work is twofold: (i) to study the damage induced by ion implantation, with special attention to low implanted doses; (ii) to study the efficiency of annealing techniques — particularly incoherent light annealing — in order to relate the electrical activity of implanted atoms to damage annealing. We have used three methods to study the damage induced by ion implantation: (1) RBS (or nuclear reactions) in random or in channeling geometry (2) RX double crystal diffractometry and (3) electrical measurements (free carrier profiling). Damage induced by silicon implantation at doses >10 14at/cm 2 can be monitored by all three techniques. However, the sensitivity of RBS is poor and hence this technique is not useful for low implantation doses. As device technology requires dopant levels in the range of 5 × 10 12 atoms/cm 2, we are particularly interested to the development of analytical techniques able to detect the damage at this implantation level. The sensitivity of such techniques was checked by studying homogeneously doped (5 × 10 16 e -/cm 3) and semi-insulating GaAs samples implanted with 3 × 10 12 silicon atoms/cm 2 at 150 keV. The substrate temperature during implantation was 200°C. The damage produced in these samples and its subsequent annealing are evidenced by strong changes in X-ray double crystal diffraction spectra. This method hence appears as a good monitoring technique. Annealing of the implanted layers has been performed using incoherent light sources (xenon lamps) either in flash or continuous conditions. Reference samples have also been thermally annealed (850°C, 20 min in capless conditions). The results are compared, and the electrical carrier profiles obtained after continuous incoherent light irradiation indicate that the implanted silicon atoms are almost dully activated. The advantages and disadvantages of incoherent light irradiation are discussed (surface oxidation, surface damage) in comparison with standard

  17. Sparse gallium arsenide to silicon metal waferbonding for heterogeneous monolithic microwave integrated circuits

    Science.gov (United States)

    Bickford, Justin Robert

    integration method. Passive bond test structures were designed, fabricated, and measured to extract the bond interface electrical behavior, electrical contact resistivity, and thermal conductivity. The In-Pd alloy, employed as the bondmetal interface between these GaAs/silicon test structures, provided a universal ohmic contact between all doping combinations. The bond interface contact resistivity between n-type GaAs and p-type Si was found to be 1.03x10-5 ohm-cm2 and a bondmetal thermal conductivity of 2.51 W/m-K was also determined. In addition, passive un-bonded and bonded microwave waveguides were constructed to test the microwave propagation properties of the bondmetal. The characteristics of these test structures qualified the metalbonding technique for use in heterogeneous microwave systems. The successful fabrication of these structures demonstrated that this metalbonding method could be extended to active devices as well, which would be of similar size, form factor, and utilize the same fabrication methods. An un-bonded active microwave waveguide, similar to one which could become common in heterogeneous microwave systems, was investigated to illustrate its unique microwave properties. This un-bonded traveling wave PIN semiconductor waveguide propagated microwaves in a 'slow-wave' manner, as a consequence of its diode structure.

  18. One watt gallium arsenide class-E power amplifier with a thin-film bulk acoustic resonator filter embedded in the output network

    Directory of Open Access Journals (Sweden)

    Kyle Holzer

    2015-05-01

    Full Text Available Integration of a class-E power amplifier (PA and a thin-film bulk acoustic wave resonator (FBAR filter is shown to provide high power added efficiency in addition to superior out-of-band spectrum suppression. A discrete gallium arsenide pseudomorphic high-electron-mobility transistor is implemented to operate as a class-E amplifier from 2496 to 2690 MHz. The ACPF7041 compact bandpass FBAR filter is incorporated to replace the resonant LC tank in a traditional class-E PA. To reduce drain voltage stress, the supply choke is replaced by a finite inductance. The fabricated PA provides up to 1 W of output power with a peak power added efficiency (PAE of 58%. The improved out-of-band spectrum filtering is compared to a traditional class-E with discrete LC resonant filtering. Such PAs can be combined with linearisation techniques to reduce out-of-band emissions.

  19. Bone tissue incorporates in vitro gallium with a local structure similar to gallium-doped brushite.

    Science.gov (United States)

    Korbas, M; Rokita, E; Meyer-Klaucke, W; Ryczek, J

    2004-01-01

    During mineral growth in rat bone-marrow stromal cell cultures, gallium follows calcium pathways. The dominant phase of the cell culture mineral constitutes the poorly crystalline hydroxyapatite (HAP). This model system mimics bone mineralization in vivo. The structural characterization of the Ga environment was performed by X-ray absorption spectroscopy at the Ga K-edge. These data were compared with Ga-doped synthetic compounds (poorly crystalline hydroxyapatite, amorphous calcium phosphate and brushite) and with strontium-treated bone tissue, obtained from the same culture model. It was found that Sr(2+) substitutes for Ca(2+) in the HAP crystal lattice. In contrast, the replacement by Ga(3+) yielded a much more disordered local environment of the probe atom in all investigated cell culture samples. The coordination of Ga ions in the cell culture minerals was similar to that of Ga(3+), substituted for Ca(2+), in the Ga-doped synthetic brushite (Ga-DCPD). The Ga atoms in the Ga-DCPD were coordinated by four oxygen atoms (1.90 A) of the four phosphate groups and two oxygen atoms at 2.02 A. Interestingly, the local environment of Ga in the cell culture minerals was not dependent on the onset of Ga treatment, the Ga concentration in the medium or the age of the mineral. Thus, it was concluded that Ga ions were incorporated into the precursor phase to the HAP mineral. Substitution for Ca(2+ )with Ga(3+) distorted locally this brushite-like environment, which prevented the transformation of the initially deposited phase into the poorly crystalline HAP.

  20. Nonlinear radiation response of n-doped indium antimonide and indium arsenide in intense terahertz field

    Science.gov (United States)

    Gong, Jiao-Li; Liu, Jin-Song; Chu, Zheng; Yang, Zhen-Gang; Wang, Ke-Jia; Yao, Jian-Quan

    2016-10-01

    The nonlinear radiation responses of two different n-doped bulk semiconductors: indium antimonide (InSb) and indium arsenide (InAs) in an intense terahertz (THz) field are studied by using the method of ensemble Monte Carlo (EMC) at room temperature. The results show that the radiations of two materials generate about 2-THz periodic regular spectrum distributions under a high field of 100 kV/cm at 1-THz center frequency. The center frequencies are enhanced to about 7 THz in InSb, and only 5 THz in InAs, respectively. The electron valley occupancy and the percentage of new electrons excited by impact ionization are also calculated. We find that the band nonparabolicity and impact ionization promote the generation of nonlinear high frequency radiation, while intervalley scattering has the opposite effect. Moreover, the impact ionization dominates in InSb, while impact ionization and intervalley scattering work together in InAs. These characteristics have potential applications in up-convension of THz wave and THz nonlinear frequency multiplication field. Project supported by the National Natural Science Foundation of China (Grant Nos. 11574105 and 61177095), the Natural Science Foundation of Hubei Province, China (Grant Nos. 2012FFA074 and 2013BAA002), the Wuhan Municipal Applied Basic Research Project, China (Grant No. 20140101010009), and the Fundamental Research Funds for the Central Universities, China (Grant Nos. 2013KXYQ004 and 2014ZZGH021).

  1. Electrical properties of boron, phosphorus and gallium co-doped silicon

    OpenAIRE

    Fourmond, Erwann; Forster, Maxime; Einhaus, Roland; Lauvray, Hubert

    2011-01-01

    à paraître dans Energy Procedia; International audience; A number of ingots were grown from solar grade poly Silicon, to which Boron, Phosphorous and Gallium were added as dopants. The introduction of Gallium as a third dopant allowed for a better control of the resistivity and the doping type during ingot growth. Measured resistivity in this material is shown to be systematically higher than that calculated using Scheil's law for the dopants distribution and Klaassen's model for the majority...

  2. On Fermi level pinning in the alloys based on the lead telluride doped with gallium

    CERN Document Server

    Skipetrov, E P; Skipetrova, L A; Volkova, O S; Slynko, E I

    2002-01-01

    Effect of doping with gallium and fast electron irradiation on the galvanomagnetic properties of n-Pb sub 1 sub - sub x Ge sub x Te (0.04 <= x <= 0.06) alloys is investigated. The transformations the metal-type conductivity are obtained both by increasing the impurity content and under the electron irradiation. The conclusion has been drawn that Fermi level pinning by the impurity level does not take place while the doping with gallium as well as the electron irradiation may serve as effective mutually complementary tools for modifying of electrical properties of alloys

  3. Gallium doping in transparent conductive ZnO thin films prepared by chemical spray pyrolysis

    Science.gov (United States)

    Babar, A. R.; Deshamukh, P. R.; Deokate, R. J.; Haranath, D.; Bhosale, C. H.; Rajpure, K. Y.

    2008-07-01

    Zinc oxide (ZnO) and ZnO : Ga films have been deposited by the spray pyrolysis method onto preheated glass substrates using zinc acetate and gallium nitrate as precursors for Zn and Ga ions, respectively. The effect of Ga doping on the structural, morphological, optical and electrical properties of sprayed ZnO thin films were investigated using x-ray diffraction (XRD), scanning electron microscopy, optical absorption, photoluminescence (PL) and Hall effect techniques. XRD studies reveal that films are polycrystalline with hexagonal (wurtzite) crystal structure. The thin films were oriented along the (0 0 2) plane. Room temperature PL measurements indicate that the deposited films exhibit proper doping of Ga in ZnO lattice. The average transparency in the visible range was around ~85-95% for typical thin film deposited using 2 at% gallium doping. The optical band gap increased from 3.31 to 3.34 eV with Ga doping of 2 at%. The addition of gallium induces a decrease in electrical resistivity of the ZnO : Ga films up to 2 at% gallium doping. The highest figure of merit observed in this present study was 3.09 × 10-3 cm2 Ω-1.

  4. Gallium doping in transparent conductive ZnO thin films prepared by chemical spray pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Babar, A R; Deshamukh, P R; Deokate, R J; Bhosale, C H; Rajpure, K Y [Electrochemical Materials Laboratory, Department of Physics, Shivaji University, Kolhapur 416 004 (India); Haranath, D [National Physical Laboratory, Dr K S Krishnan Road, New Delhi 110 012 (India)], E-mail: rajpure@yahoo.com

    2008-07-07

    Zinc oxide (ZnO) and ZnO : Ga films have been deposited by the spray pyrolysis method onto preheated glass substrates using zinc acetate and gallium nitrate as precursors for Zn and Ga ions, respectively. The effect of Ga doping on the structural, morphological, optical and electrical properties of sprayed ZnO thin films were investigated using x-ray diffraction (XRD), scanning electron microscopy, optical absorption, photoluminescence (PL) and Hall effect techniques. XRD studies reveal that films are polycrystalline with hexagonal (wurtzite) crystal structure. The thin films were oriented along the (0 0 2) plane. Room temperature PL measurements indicate that the deposited films exhibit proper doping of Ga in ZnO lattice. The average transparency in the visible range was around {approx}85-95% for typical thin film deposited using 2 at% gallium doping. The optical band gap increased from 3.31 to 3.34 eV with Ga doping of 2 at%. The addition of gallium induces a decrease in electrical resistivity of the ZnO : Ga films up to 2 at% gallium doping. The highest figure of merit observed in this present study was 3.09 x 10{sup -3} cm{sup 2} {omega}{sup -1}.

  5. Analysis of radiation-damaged and annealed gallium arsenide and indium phosphide solar cells using deep-level transient spectroscopy techniques. Master's thesis

    Energy Technology Data Exchange (ETDEWEB)

    Pinzon, D.

    1991-03-01

    Degradation of solar cell performance from radiation damage was found to be reversed through annealing processes. The mechanisms behind the degradation and recovery is based on deep-level traps, or defects, in the lattice structure of the solar cell. Through a process known as Deep Level Transient Spectroscopy (DLTS), a correlation can be made between damage/recovery and trap energy level/concentration of the cell. Gallium Arsenide (GaAs) and Indium Phosphide (InP) solar cells were subjected to 1 MeV electron irradiation by a Dynamitron linear acceleration at two fluence levels of 1E1r and 1E15 electrons/cm sq. The process of annealing included thermal annealing at 90 c with forward bias current and thermal annealing alone for (GaAs). After each cycle, DLTS measurements were taken to determine the energy level of the traps and their concentration. Multiple cycles of irradiation, annealing and DLTS were performed to observe the correlation between degradation and recovery to trap energy level and concentration. The results show that the lower energy level traps are associated with the recovery of the cells while the higher level traps are associated with the overall permanent degradation of the cells.

  6. The effect of gallium arsenide aluminum laser therapy in the management of cervical myofascial pain syndrome: a double blind, placebo-controlled study.

    Science.gov (United States)

    Dundar, U; Evcik, D; Samli, F; Pusak, H; Kavuncu, V

    2007-06-01

    The efficacy of low-level laser therapy (LLLT) in myofascial pain syndrome (MPS) seems controversial. A prospective, double-blind, randomized controlled trial was conducted in patients with chronic MPS in the neck to evaluate the effects of low-level 830-nm gallium arsenide aluminum (Ga-As-Al) laser therapy. The study group consisted of 64 MPS patients. The patients were randomly assigned into two groups. In group 1 (n = 32), Ga-As-Al laser treatment was applied over three trigger points bilaterally for 2 min over each point once a day for 15 days during a period of 3 weeks. In group 2 (n = 32), the same treatment protocol was given, but the laser instrument was switched off during applications. All patients in both groups performed daily isometric exercise and stretching exercises for cervical region. Parameters were measured at baseline and after 4 weeks. All patients were evaluated with respect to pain (at rest, movement, and night) and assessed by visual analog scale, measurement of active range of motion using an inclinometer and a goniometer, and the neck disability index. In both groups, statistically significant improvements were detected in all outcome measures compared with baseline (p 0.05). In conclusion, although the laser therapy has no superiority over placebo groups in this study, we cannot exclude the possibility of effectivity with another treatment regimen including different laser wavelengths and dosages (different intensity and density and/or treatment interval).

  7. Novel approach for n-type doping of HVPE gallium nitride with germanium

    Science.gov (United States)

    Hofmann, Patrick; Krupinski, Martin; Habel, Frank; Leibiger, Gunnar; Weinert, Berndt; Eichler, Stefan; Mikolajick, Thomas

    2016-09-01

    We present a novel method for germanium doping of gallium nitride by in-situ chlorination of solid germanium during the hydride vapour phase epitaxy (HVPE) process. Solid germanium pieces were placed in the doping line with a hydrogen chloride flow directed over them. We deduce a chlorination reaction taking place at 800 ° C , which leads to germanium chloroform (GeHCl3) or germanium tetrachloride (GeCl4). The reactor shows a germanium rich residue after in-situ chlorination experiments, which can be removed by hydrogen chloride etching. All gallium nitride crystals exhibit n-type conductivity, which shows the validity of the in-situ chlorination of germanium for doping. A complex doping profile is found for each crystal, which was assigned to a combination of localised supply of the dopant and sample rotation during growth and switch-off effects of the HVPE reactor.

  8. Properties of Erbium and Ytterbium Doped Gallium Nitride Layers Fabricated by Magnetron Sputtering

    Directory of Open Access Journals (Sweden)

    V. Prajzler

    2006-01-01

    Full Text Available We report about some properties of erbium and erbium/ytterbium doped gallium nitride (GaN layers fabricated by magnetron sputtering onsilicon, quartz and Corning glass substrates. For fabricating GaN layers two types of targets were used - gallium in a stainless steel cup anda Ga2O3 target. Deposition was carried out in the Ar+N2 gas mixture. For erbium and ytterbium doping into GaN layers, erbium metallicpowder and ytterbium powder or Er2O3 and Yb2O3 pellets were laid on the top of the target. The samples were characterized by X-raydiffraction (XRD, photoluminescence spectra and nuclear analytical methods. While the use of a metallic gallium target ensured thedeposition of well-developed polycrystalline layers, the use of gallium oxide target provided GaN films with poorly developed crystals. Bothapproaches enabled doping with erbium and ytterbium ions during deposition, and typical emission at 1 530 nm due to the Er3+ intra-4f 4I13/2 → 4I15/2 transition was observed.

  9. Morphology evolution of hydrothermally grown ZnO nanostructures on gallium doping and their defect structures

    Energy Technology Data Exchange (ETDEWEB)

    Pineda-Hernandez, G. [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico); Escobedo-Morales, A., E-mail: alejandroescobedo@hotmail.com [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico); Pal, U. [Instituto de Fisica, Benemerita Universidad Autonoma de Puebla, Apdo. Postal J-48, C.P. 72570 Puebla, Pue. (Mexico); Chigo-Anota, E. [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico)

    2012-08-15

    In the present article, the effect of gallium doping on the morphology, structural, and vibrational properties of hydrothermally grown ZnO nanostructures has been studied. It has been observed that incorporated gallium plays an important role on the growth kinetics and hence on the morphology evolution of the ZnO crystals. Ga doping in high concentration results in the contraction of ZnO unit cell, mainly along c-axis. Although Ga has high solubility in ZnO, heavy doping promotes the segregation of Ga atoms as a secondary phase. Incorporated Ga atoms strongly affect the vibrational characteristics of ZnO lattice and induce anomalous Raman modes. Possible mechanisms of morphology evolution and origin of anomalous Raman modes in Ga doped ZnO nanostructures are discussed. -- Highlights: Black-Right-Pointing-Pointer Ga doped ZnO nanostructures were successfully grown by hydrothermal chemical route. Black-Right-Pointing-Pointer Ga doping has strong effect on the resulting morphology of ZnO nanostructures. Black-Right-Pointing-Pointer Anomalous vibrational modes in wurtzite ZnO lattice are induced by Ga doping. Black-Right-Pointing-Pointer Incorporated Ga atoms accommodate at preferential lattice sites.

  10. Characterization of ALD Processed Gallium Doped TiO2 Hole Blocking Layer in an Inverted Organic Solar Cell

    Science.gov (United States)

    Lee, Eun Ju; Ryu, Sang Ouk

    2016-10-01

    To improve power conversion efficiency (PCE) of inverted structure organic solar cells a buffer layer, a hole blocking layer (HBL) was introduced between cathode and active photovoltaic layer. Gallium (Ga) doped TiO2 as a HBL was fabricated by means of atomic layer deposition. X-ray photoelectron spectroscopy showed the highest Ga-Ti complex binding characteristics was achieved at 5% doping concentration. Gallium doped TiO2 layer exhibited over 94% of optical transmittance at the process temperature of 200°C. The resulting PCE of inverted structure organic solar cell having 5% doping in the hole block layer was 2.7%. The PCE was improved 35% compared to the cell without gallium doping.

  11. Characterization of ALD Processed Gallium Doped TiO2 Hole Blocking Layer in an Inverted Organic Solar Cell

    Science.gov (United States)

    Lee, Eun Ju; Ryu, Sang Ouk

    2017-02-01

    To improve power conversion efficiency (PCE) of inverted structure organic solar cells a buffer layer, a hole blocking layer (HBL) was introduced between cathode and active photovoltaic layer. Gallium (Ga) doped TiO2 as a HBL was fabricated by means of atomic layer deposition. X-ray photoelectron spectroscopy showed the highest Ga-Ti complex binding characteristics was achieved at 5% doping concentration. Gallium doped TiO2 layer exhibited over 94% of optical transmittance at the process temperature of 200°C. The resulting PCE of inverted structure organic solar cell having 5% doping in the hole block layer was 2.7%. The PCE was improved 35% compared to the cell without gallium doping.

  12. NTP Toxicology and Carcinogenesis Studies of Gallium Arsenide (CAS No. 1303-00-0) in F344/N Rats and B6C3F1 Mice (Inhalation Studies).

    Science.gov (United States)

    2000-09-01

    Gallium arsenide is used primarily to make light- emitting diodes, lasers, laser windows, and photodetectors and in the photoelectronic transmission of data through optical fibers. Gallium arsenide was nominated for study because of its widespread use in the microelectronics industry, the potential for worker exposure, and the absence of chronic toxicity data. Male and female F344/N rats and B6C3F1 mice were exposed to gallium arsenide particles (greater than 98% pure; mass median aerodynamic diameter = 0.8 to 1.0 &mgr;m) by inhalation for 16 days, 14 weeks, or 2 years. Genetic toxicology studies were conducted in Salmonella typhimurium, and the frequency of micronuclei was determined in the peripheral blood of mice exposed to gallium arsenide for 14 weeks. 16-DAY STUDY IN RATS: Groups of five male and five female rats were exposed to particulate aerosols of gallium arsenide with a mass median aerodynamic diameter of approximately 1 &mgr;m at concentrations of 0, 1, 10, 37, 75, or 150 mg/m(3) by inhalation, 6 hours per day, 5 days per week, for 16 days. All rats survived to the end of the study. The final mean body weights of all exposed groups of males and females were similar to those of the chamber controls. Compared to chamber controls, the liver and lung weights of males exposed to 1 mg/m(3) or greater and females exposed to 10 mg/m(3) or greater were increased; the thymus weights of all exposed groups of males were decreased. Gallium arsenide particles were visible in the alveolar spaces and, to a lesser extent, within alveolar macrophages of exposed rats. Moderate proteinosis (surfactant mixed with small amounts of fibrin) and minimal histiocytic cellular infiltrate were observed in the alveoli of exposed males and females. Epithelial hyperplasia and squamous metaplasia of the larynx were observed primarily in males exposed to 150 mg/m(3). 16-DAY STUDY IN MICE: Groups of five male and four or five female mice were exposed to particulate aerosols of gallium

  13. Properties Of Gallium-doped Hydrogenated Amorphous Germanium

    OpenAIRE

    1995-01-01

    The effects of adding small quantities of gallium atoms to hydrogenated amorphous germanium (a-Ge:H) on its dark-conductivity, band-gap, electronic density of states and the hydrogen bonding, were studied in detail by dark-conductivity, optical and infrared-transmission, and photothermal- deflection-spectroscopy measurements. Films of a-Ge:H having relative Ga atomic concentrations ranging between 3×10-5 and 1×10-2 were deposited by the cosputtering of solid Ge and Ga targets in a rf-plasma s...

  14. Design of Indium Arsenide nanowire sensors for pH and biological sensing and low temperature transport through p-doped Indium Arsenide nanowires

    DEFF Research Database (Denmark)

    Upadhyay, Shivendra

    remains the primary material of choice. This research is about investigating Indium Arsenide nanowires as alternative platform for sensing charged species - chemical and biological, in solution. Starting with nanowires grown via molecular beam epitaxy in an ultra-high vacuum chamber, we discuss...

  15. Sub-Half Micrometer Gate Lift-Off By Three Layer Resist Process Via Electron Beam Lithography For Gallium Arsenide Monolithic Microwave Integrated Circuits (MIMICs)

    Science.gov (United States)

    Nagarajan, Rao M.; Rask, Steven D.; King, Michael R.; Yard, Thomas K.

    1988-06-01

    A three layer resist process for gate lift-oft on Gallium Arsenide MIMICs by electron Dean and optical lithographies are described. The electron beam lithography process consists of Poly (Dimethyl Glutarimide) PMGI as tne planarizing layer, a Plasma Enhanced Chemical Vapour Deposition silicon nitride (SiN) as an intermediate barrier layer and Poly (Methyl methacrylate), PMMA, as the top imaging layer. The PivimA is exposed by Cambridge Electron beam system EBMF 6.4 at 20kev and developed in Methyl Ethyl Ketone/Iso Propyl Alcohol. The pattern is then transferred to the SiN layer by cF4/o2 plasma etcning. The SiN layer is then used as the mask to transfer the pattern to the PMGI layer by 02 kteactive Ion Etching until tne GaAS is exposed. The various processing parameters are optimized to obtain lip or overnang suitable for lift-off with 0.20μm gate dimension. After the GaAS has been recessed (to reduce the parasitic source resistance), a thick 9000Å Ti/Pt/Au gate metal is evaporated and the unwanted gate metal is lifted oft using PMGI stripper. To use the three layer resist process in optical litnograpny, the MG.'. planarizing layer and PECVD SiN layer is used along with optical pnotoresist AZ1450J as a top imaging layer. inc sofcbake, uV exposure dose (436 nm) and development time for AZ145UJ are optimized to obtain 0.5μm to 1.0μm gate dimensions. The etch parameters for the pattern transfer to SiN and tnen to PMGI layers are same as in tne above process. The process levels such as mesa, source/drain, contact and metal levels for GaAs mlivilt,s are defined by UV lithography (Karl Suss contact aligner) using single layer pnotoresist. A nign overlay accuracy is obtained by use of gold metal Dumps as registration marks for aligning tne electron Dean exposed gate to optically exposed source/drain channel. Thus a higher tnrougnput and better linewidtn control are obtained using electron beam/optical lithography tecnniques. This approach is currently used to

  16. Faraday effect improvement by Dy{sup 3+}-doping of terbium gallium garnet single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zhe, E-mail: zhenzhe1201@sina.com; Yang, Lei; Hang, Yin; Wang, Xiangyong

    2016-01-15

    Highly transparent Dy{sup 3+}-doped terbium gallium garnet (TGG) single crystal was grown by Czochralski (Cz) method. Phase composition of the crystal was tested by XRD measurements. The distribution coefficient of Dy{sup 3+} in the crystal was obtained. The optical and magneto-optical properties were analyzed in detail, and magnetic properties of the Dy{sup 3+}-TGG crystal were studied. The paramagnetic behavior is observed down to 10 K. The as-grown crystal exhibited high optical transmittance, particularly in the visible region. The Faraday rotation was investigated over visible and near-infrared regions (VIS–NIR) at room temperature. The Verdet constants increase at measured wavelengths and high thermal stability was found in Dy{sup 3+}-doped TGG, as compared to the properties of pure TGG, indicating that Dy{sup 3+}-doped crystals are preferable for magneto-active materials used in Faraday devices at VIS–NIR wavelengths. - Graphical abstract: Highly transparent Dy{sup 3+}-doped terbium gallium garnet (TGG) and pure TGG single crystals were grown by Czochralski method. The Dy{sup 3+}-doped TGG possesses 20–30% higher Verdet values in reference to TGG independently on wavelength.

  17. High magneto-optical characteristics of Holmium-doped terbium gallium garnet crystal.

    Science.gov (United States)

    Chen, Zhe; Yang, Lei; Wang, Xiangyong; Yin, Hang

    2016-06-01

    Magneto-optical characteristics of a new magneto-active material, (Tb(1-x)Hox)3Ga5O12 crystal, have been grown by the Czochralski (Cz) method. A high value of the Verdet constant was obtained at room temperature-namely, 214.9 and 77.8  rad·m-1 T-1 for 632.8 and 1064 nm, respectively. The Verdet constant of the Ho-doped terbium gallium garnet crystal at 1064 nm is about 2 times higher than that of terbium gallium garnet crystal. High value of magneto-optical figure-of-merit makes it an attractive next-generation magneto-optics material for high-power Faraday isolators.

  18. Quantificaion of ion diffusion in gallium arsenide-based spintronic Light-Emitting Diode devices using time-of-flight secondary ion mass spectrometry

    Science.gov (United States)

    Cogswell, Jeffrey Ryan

    Depth profiling using Secondary Ion Mass Spectrometry (SIMS) is a direct method to measure diffusion of atomic or molecular species that have migrated distances of nanometers/micrometers in a specific material. For this research, the diffusion of Mn, sequentially Ga ions, in Gallium Arsenide (GaAs)-based spin Light Emitting Diode (LED) devices is studied by quantitative Time-of-Flight (ToF) SIMS. The goal is to prove conclusively the driving force and mechanism behind Mn diffusion in GaAs by quantifying the diffusion of these ions in each device. Previous work has identified two competing processes for the movement of Mn in GaAs: diffusion and phase separation. The process is dependent on the temperature the sample is exposed to, either by post-annealing, or during the molecular beam epitaxy (MBE) growth process. The hypothesis is that Manganese Arsenide (MnAs) is thermodynamically more stable than randomly distributed Mn ions in GaAs, and that by annealing at a certain temperature, a pure MnAs layer can be produced from a GaMnAs layer in a working spin LED device. Secondly, the spin efficiencies will be measured and the difference will be related to the formation of a pure MnAs layer. The first chapter of this dissertation discusses the history of spintronic devices, including details on the established methods for characterization, the importance for potential application to the semiconductor industry, and the requirements for the full implementation of spintronic devices in modern-day computers. MnAs and GaMnAs devices are studied, their preparation and properties are described, and the study's experimental design is covered in the latter part of Chapter 1. Chapter 2 includes a review of diffusion in semiconductors, including the types of diffusion, mechanisms they follow, and the different established experimental methods for studying diffusion. The later sections include summaries of Mn diffusion and previous studies investigating Mn diffusion in different

  19. Properties of dysprosium-doped gallium lanthanum sulfide fiber amplifiers operating at 1.3 microm.

    Science.gov (United States)

    Samson, B N; Schweizer, T; Hewak, D W; Laming, R I

    1997-05-15

    In light of recent progress in the fabrication of gallium lanthanum sulfide (GaLaS) fibers, we have modeled the performance of dysprosium-doped GaLaS fiber amplifiers operating at 1.3 microm . Based on experimental data, we find that the incorporation of a codopant (terbium) in the fiber core significantly shortens the optimum amplifier length from >30 m to approximately 3 m . Such a device may be practical, given the fiber losses currently achieved in GaLaS fibers.

  20. Strongly localized donor level in oxygen doped gallium nitride

    Energy Technology Data Exchange (ETDEWEB)

    Wetzel, C.; Suski, T.; Ager, J.W. III [Lawrence Berkeley National Lab., CA (United States); Fischer, S.; Meyer, B.K. [Giessen Univ. (Germany). 1. Physikalisches Inst.; Grzegory, I.; Porowski, S. [Polska Akademia Nauk, Warsaw (Poland)

    1996-08-01

    A classification in terms of localization of donor defects in GaN is performed by Raman spectroscopy under large hydrostatic pressure. We observe a significant decrease of free carrier concentration in highly O doped GaN epitaxial films at 22 GPa, indicating the presence of a strongly localized donor defect at large pressure. Monitoring the phonon plasmon coupled mode, we find similarities with results on highly n-type bulk crystals. We refine the model of localized defects in GaN and transfer it to the AlGaN system.

  1. Sol-gel deposition and plasma treatment of intrinsic, aluminum-doped, and gallium-doped zinc oxide thin films as transparent conductive electrodes

    Science.gov (United States)

    Zhu, Zhaozhao; Mankowski, Trent; Balakrishnan, Kaushik; Shikoh, Ali Sehpar; Touati, Farid; Benammar, Mohieddine A.; Mansuripur, Masud; Falco, Charles M.

    2015-09-01

    Zinc oxide and aluminum/gallium-doped zinc oxide thin films were deposited via sol-gel spin-coating technique. Employing plasma treatment as alternative to post thermal annealing, we found that the morphologies of these thin films have changed and the sheet resistances have been significantly enhanced. These plasma-treated thin films also show very good optical properties, with transmittance above 90% averaged over the visible wavelength range. Our best aluminum/gallium-doped zinc oxide thin films exhibit sheet resistances (Rs) of ~ 200 Ω/sq and ~ 150 Ω/sq, respectively.

  2. Waveguide amplifiers in sputtered films of Er3+-doped gallium lanthanum sulfide glass

    Science.gov (United States)

    Frantz, J. A.; Shaw, L. B.; Sanghera, J. S.; Aggarwal, I. D.

    2006-03-01

    Waveguide amplifiers fabricated in Er3+-doped gallium lanthanum sulfide (GLS) glass are demonstrated. GLS is deposited onto fused silica substrates by RF magnetron sputtering, and waveguides are patterned by use of the lift-off technique. The waveguides exhibit a total internal gain of 6.7 dB (2.8 dB/cm) for a signal with a wavelength of 1.55 μm. This experiment is, to the best of our knowledge, the first demonstration of gain in an Er3+-doped chalcogenide glass waveguide. The fabrication methods we apply, if used with other rare earth dopants, could potentially be employed to produce sources operating in the mid-IR.

  3. Magnetic properties of gadolinium and carbon co-doped gallium nitride

    Science.gov (United States)

    Syed Kaleemullah, N.; Ramsubramanian, S.; Mohankumar, R.; Munawar Basha, S.; Rajagopalan, M.; Kumar, J.

    2017-01-01

    Investigations have been carried out to study the ferromagnetic properties of Gadolinium (Gd) Carbon (C) co-doped wurtzite Gallium Nitride (GaN) using full-potential linear augmented plane wave (FP-LAPW) method within the density functional theory. The system shows half-metallic nature when single Gd is substituted in Ga36N36 supercell. The presence of carbon in GaN supercell is found to generate weak magnetic moment (Ms) in the neighbouring atoms. When Carbon is codoped in the Gd-GaN, it increased the total magnetic moment of the system (Mtot). The cause of ferromagnetism in the Gd and C co-doped GaN has been explained by Zener's p-d exchange mechanism. The role of defects in the magnetic property of this system is also investigated. The results indicate the gallium vacancy influences the magnetic moment of the Gd and C codoped GaN more than the nitrogen vacancy. The presence of holes is effective than electrons in achieving the ferromagnetism in the considered system.

  4. Tunable White Fluorescent Copper Gallium Sulfide Quantum Dots Enabled by Mn Doping.

    Science.gov (United States)

    Jo, Dae-Yeon; Kim, Daekyoung; Kim, Jong-Hoon; Chae, Heeyeop; Seo, Hyo Jin; Do, Young Rag; Yang, Heesun

    2016-05-18

    Fluorescence of semiconductor quantum dots (QDs) can be tuned by engineering the band gap via size and composition control and further doping them with impurity ions. Targeting on highly bright white-emissive I-III-VI -type copper gallium sulfide (Cu-Ga-S, CGS) host QDs with the entire visible spectral coverage of blue to red, herein, Mn(2+) ion doping, through surface adsorption and lattice diffusion is fulfilled. Upon doping a distinct Mn emission from (4)T1-(6)A1 transition successfully appears in white photoluminescence (PL) of undoped CGS/ZnS core/shell QDs and with varying Mn concentration a systematic white spectral evolution of CGS:Mn/ZnS QDs is achievable with high PL quantum yield retained. The origins of white PL of CGS:Mn/ZnS QDs that is well decomposed into three emission bands are appropriately assigned. The resulting single-phased, doped QDs are then employed as near-UV-to-white down converters for the fabrication of white light-emitting diodes (LEDs). Electroluminescent properties of white QD-LEDs depending on Mn concentration of CGS:Mn/ZnS QDs and forward current are also discussed in detail.

  5. Superconductivity around quantum critical point in P-doped iron arsenides

    Energy Technology Data Exchange (ETDEWEB)

    Cao Guanghan, E-mail: ghcao@zju.edu.c [Department of Physics, Zhejiang University, Hangzhou 310027 (China); Jiang Shuai; Wang Cao; Li Yuke; Ren Zhi; Tao Qian; Dai Jianhui; Xu Zhuan [Department of Physics, Zhejiang University, Hangzhou 310027 (China)

    2010-12-15

    We demonstrate that, by the P/As substitution-without doping of charge carriers-in a FeAs-layer-based parent compound, superconductivity can be universally introduced. The maximum superconducting critical temperature (T{sub c}) of BaFe{sub 2}(As{sub 1-x}P{sub x}){sub 2} achieves 30 K. The P doping in LnFeAsO system (Ln = La and Sm) produces superconductivity below 11 K. The normal-state resistivity obeys linear temperature dependence and the normal-state Hall coefficient shows strong temperature dependence. These non-Fermi liquid behaviors suggest magnetic quantum criticality. The maximum T{sub c} values in different systems correlates strongly with the diagonal bondangle of Fe-As-Fe, implying the important role of the next-nearest-neighbor magnetic exchange coupling in iron pnictide superconductors.

  6. Magnetic properties of manganites doped with gallium, iron, and chromium ions

    Energy Technology Data Exchange (ETDEWEB)

    Troyanchuk, I. O., E-mail: troyan@physics.by; Bushinsky, M. V.; Tereshko, N. V. [National Academy of Sciences of Belarus, Scientific and Practical Materials Research Center (Belarus); Dobryanskii, V. M. [Belarussian State Agrarian Technical University (Belarus); Sikolenko, V. [Joint Institute for Nuclear Research (Russian Federation); Többens, D. M. [Helmholtz Center (Germany)

    2015-05-15

    The magnetization and the crystal structure of the La{sub 0.7}Sr{sub 0.3}Mn{sub 1−x}M{sub x}O{sub 3} (M = Ga, Fe, Cr; x ≤ 0.3) systems are studied. The substitution of gallium and chromium is shown to cause phase separation into antiferromagnetic and ferromagnetic phases, whereas the substitution of iron for manganese stabilizes a spinglass state. The ferromagnetic phase in the chromium-substituted compositions is much more stable than that in the case of substitution by iron ions or diamagnetic gallium ions. The magnetic properties are explained in terms of the model of superexchange interactions and the localization of most e{sub g} electrons of manganese. The stabilization of ferromagnetism in the chromium-substituted compositions can be caused by the fact that the positive and negative contributions to the superexchange interaction between Mn{sup 3+} and Cr{sup 3+} ions are close to each other but the antiferromagnetic part of the exchange is predominant. Moreover, some chromium ions are in the tetravalent state, which maintains the optimum doping conditions.

  7. Effect of gallium environment on infrared emission in Er3+-doped gallium– antimony– sulfur glasses

    Science.gov (United States)

    Jiao, Qing; Li, Ge; Li, Lini; Lin, Changgui; Wang, Guoxiang; Liu, Zijun; Dai, Shixun; Xu, Tiefeng; Zhang, Qinyuan

    2017-01-01

    Gallium-based Ga–Sb–S sulfide glasses was elaborated and studied. A relationship between the structure, composition, and optical properties of the glass has been established. The effects of the introduction of Ga on the structure using infrared and Raman spectroscopies and on the Er3+-doped IR emission have been discussed. The results show that incorporation of Ga induced the dissociation of [SbS3] pyramids units and the formation of tetrahedral [GaS4] units. The dissolved rare earth ions are separated around the Ga–S bonding and the infrared emission quenching are controlled. Moreover, continuous introduction of Er ions into the glass forms more Er–S bonds through the further aggregation surrounding the [GaS4] units. In return, the infrared emission intensity decreased with excessive Er ion addition. This phenomenon is correlated with the recurrence concentration quenching effect induced by the increase of [GaS4] units. PMID:28106143

  8. Characterization and properties of novel gallium-doped calcium phosphate ceramics.

    Science.gov (United States)

    Mellier, Charlotte; Fayon, Franck; Schnitzler, Verena; Deniard, Philippe; Allix, Mathieu; Quillard, Sophie; Massiot, Dominique; Bouler, Jean-Michel; Bujoli, Bruno; Janvier, Pascal

    2011-09-05

    Addition of a gallium (Ga) precursor in the typical reaction protocols used for the preparation of β-tricalcium phosphate (β-TCP) led to novel Ga-doped β-TCP ceramics with rhombohedral structures (R3c space group). From the refinement of their X-ray diffraction patterns, it was found that the incorporation of Ga in the β-TCP network occurs by substitution of one of the five calcium (Ca) sites, while occupation of another Ca site decreases in inverse proportion to the Ga content in the structure. The Ga local environment and the modification of the phosphorus environments due to the Ga/Ca substitution in Ga-doped β-TCP compounds are probed using (31)P and (71)Ga magic-angle spinning NMR. A decrease of the unit cell volume is observed with increasing Ga content, together with improved mechanical properties. Indeed, the compressive strength of these new bioceramics is enhanced in direct proportion of the Ga content, up to a 2.6-fold increase as compared to pure β-TCP.

  9. Negative permittivity of ZnO thin films prepared from aluminum and gallium doped ceramics via pulsed-laser deposition

    DEFF Research Database (Denmark)

    Bodea, M. A.; Sbarcea, G.; Naik, G. V.

    2013-01-01

    Aluminum and gallium doped zinc oxide thin films with negative dielectric permittivity in the near infrared spectral range are grown by pulsed laser deposition. Composite ceramics comprising ZnO and secondary phase Al2O3 or Ga2O3 are employed as targets for laser ablation. Films deposited on glass...... from dense and small-grained ceramic targets show optical transmission larger than 70 % in the visible and reveal an onset of metallic reflectivity in the near infrared at 1100 nm and a crossover to a negative real part of the permittivity at approximately 1500 nm. In comparison to noble metals, doped...

  10. Effect of uniaxial stress on gallium, beryllium, and copper-doped germanium hole population inversion lasers

    Energy Technology Data Exchange (ETDEWEB)

    Chamberlin, Danielle Russell [Univ. of California, Berkeley, CA (United States)

    1998-05-01

    The effects of stress on germanium lasers doped with single, double, and triple acceptors have been investigated. The results can be explained quantitatively with theoretical calculations and can be attributed to specific changes in the energy levels of acceptors in germanium under stress. In contrast to previous measurements, gallium-doped Ge crystals show a decrease in lasing upon uniaxial stress. The decrease seen here is attributed to the decrease in heavy hole effective mass upon application of uniaxial stress, which results in a decreased population inversion. The discrepancy between this work and previous studies can be explained with the low compensation level of the material used here. Because the amount of ionized impurity scattering in low-compensated germanium lasers is small to begin with, the reduction in scattering with uniaxial stress does not play a significant role in changing the laser operation. Beryllium-doped germanium lasers operate based on a different mechanism of population inversion. In this material it is proposed that holes can transfer between bands by giving their energy to a neutral beryllium atom, raising the hole from the ground to a bound excited state. The free hole will then return to zero energy with some probability of entering the other band. The minimum and maximum E/B ratios for lasing change with uniaxial stress because of the change in effective mass and bound excited state energy. These limits have been calculated for the case of 300 bar [100] stress, and match very well with the observed data. This adds further credence to the proposed mechanism for population inversion in this material. In contrast to Be and Ga-doped lasers, copper-doped lasers under uniaxial stress show an increase in the range of E and B where lasing is seen. To understand this change the theoretical limits for population inversion based on both the optical phonon mechanism and the neutral acceptor mechanism have been calculated. The data are

  11. Superconductivity in Ti-doped iron-arsenide compound Sr4Cr0.8Ti1.2O6Fe2As2

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Superconductivity was achieved in Ti-doped iron-arsenide compound Sr4Cr0.8Ti1.2O6Fe2As2 (abbreviated as Cr-FeAs-42622). The X-ray diffraction measurement shows that this material has a layered structure with the space group of P4/nmm,and with the lattice constants a = b = 3.9003  and c = 15.8376 . Clear diamagnetic signals in ac susceptibility data and zero-resistance in resistivity data were detected at about 6 K,confirming the occurrence of bulk superconductivity. Meanwhile we observed a supercon-ducting transition in the resistive data with the onset transition temperature at 29.2 K,which may be induced by the nonuniform distribution of the Cr/Ti content in the FeAs-42622 phase.

  12. Intrinsic and metal-doped gallium oxide based high-temperature oxygen sensors for combustion processes

    Science.gov (United States)

    Rubio, Ernesto Javier

    Currently, there is enormous interest in research, development and optimization of the combustion processes for energy harvesting. Recent statistical and economic analyses estimated that by improving the coal-based firing/combustion processes in the power plants, savings up to $450-500 million yearly can be achieved. Advanced sensors and controls capable of withstanding extreme environments such as high temperatures, highly corrosive atmospheres, and high pressures are critical to such efficiency enhancement and cost savings. For instance, optimization of the combustion processes in power generation systems can be achieved by sensing, monitoring and control of oxygen, which is a measure of the completeness of the process and can lead to enhanced efficiency and reduced greenhouse gas emissions. However, despite the fact that there exists a very high demand for advanced sensors, the existing technologies suffer from poor 'response and recovery times' and 'long-term stability.' Motivated by the aforementioned technological challenges, the present work was focused on high-temperature (≥700 °C) oxygen sensors for application in power generation systems. The objective of the present work is to investigate nanostructured gallium oxide (2O3) based sensors for oxygen sensing, where we propose to conduct in-depth exploration of the role of refractory metal (tungsten, W, in this case) doping into 2O 3 to enhance the sensitivity, selectivity, stability ("3S" criteria) and reliability of such sensors while keeping cost economical. Tungsten (W) doped gallium oxide (2O3) thin films were deposited via rf-magnetron co-sputtering of W-metal and Ga2O3-ceramic targets. Films were produced by varying the sputtering power applied to the W-target in order to achieve variable W content into 2O3 films while substrate temperature was kept constant at 500 °C. Chemical composition, chemical valence states, microstructure and crystal structure of as-grown and post-annealed W-doped 2O3

  13. Electrical and optical properties of silicon-doped gallium nitride polycrystalline films

    Indian Academy of Sciences (India)

    S R Bhattacharyya; A K Pal

    2008-02-01

    Si-doped GaN films in polycrystalline form were deposited on quartz substrates at deposition temperatures ranging from 300–623 K using r.f. sputtering technique. Electrical, optical and microstructural properties were studied for these films. It was observed that films deposited at room temperature contained mainly hexagonal gallium nitride (ℎ-GaN) while films deposited at 623 K were predominantly cubic (-GaN) in nature. The films deposited at intermediate temperatures were found to contain both the hexagonal and cubic phases of GaN. Studies on the variation of conductivity with temperature indicated Mott’s hopping for films containing -GaN while Efros and Shklovskii (E–S) hopping within the Coulomb gap was found to dominate the carrier transport mechanism in the films containing ℎ-GaN. A crossover from Mott’s hopping to E–S hopping in the `soft’ Coulomb gap was noticed with lowering of temperature for films containing mixed phases of GaN. The relative intensity of the PL peak at ∼ 2.73 eV to that for peak at ∼ 3.11 eV appearing due to transitions from deep donor to valence band or shallow acceptors decreased significantly at higher temperature. Variation of band gap showed a bowing behaviour with the amount of cubic phase present in the films.

  14. The effect of sub-oxide phases on the transparency of tin-doped gallium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Lim, K. [Department of Materials Science and Engineering, Stanford University, Stanford, California 94305, USA; Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025, USA; Schelhas, L. T. [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025, USA; Siah, S. C. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Brandt, R. E. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Zakutayev, A. [National Renewable Energy Laboratory, Golden, Colorado 80401, USA; Lany, S. [National Renewable Energy Laboratory, Golden, Colorado 80401, USA; Gorman, B. [Department of Materials Science and Engineering, Colorado School of Mines, Golden, Colorado 80401, USA; Sun, C. J. [Advanced Photon Source, Argonne National Laboratory, Lemont, Illinois 60439, USA; Ginley, D. [National Renewable Energy Laboratory, Golden, Colorado 80401, USA; Buonassisi, T. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA; Toney, M. F. [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025, USA

    2016-10-03

    There have been a number of studies on the fabrication of Sn-doped gallium oxide (Ga2O3:Sn) films with both conductive and transparent properties using a variety of deposition methods. However, often, synthesis results in films that are not transparent. In this paper, we examine the mechanisms underlying these results in Ga2O3:Sn thin films prepared at various growth temperatures, Sn concentrations, and oxygen partial pressures. With X-ray absorption spectroscopy, transmission electron microscopy and energy dispersive spectroscopy, we find that when films are grown under the oxygen deficient conditions there are Ga sub-oxide and SnOx phases in the Ga2O3:Sn thin film. These Ga sub-oxide phases are only found in non-transparent films, and so we infer that the Ga sub-oxide is responsible for the non-transparency. These observations suggest that to obtain transparent Ga2O3:Sn, films deposition or subsequent annealing must be carefully controlled in both temperature and oxygen partial pressure to avoid the formation of Ga sub-oxide phases.

  15. The effect of sub-oxide phases on the transparency of tin-doped gallium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Lim, K.; Schelhas, L. T.; Siah, S. C.; Brandt, R. E.; Zakutayev, A.; Lany, S.; Gorman, B.; Sun, C. J.; Ginley, D.; Buonassisi, T.; Toney, M. F.

    2016-10-03

    There have been a number of studies on the fabrication of Sn-doped gallium oxide (Ga2O3:Sn) films with both conductive and transparent properties using a variety of deposition methods. However, often, synthesis results in films that are not transparent. In this paper, we examine the mechanisms underlying these results in Ga2O3:Sn thin films prepared at various growth temperatures, Sn concentrations, and oxygen partial pressures. With X-ray absorption spectroscopy, transmission electron microscopy and energy dispersive spectroscopy, we find that when films are grown under the oxygen deficient conditions there are Ga sub-oxide and SnOx phases in the Ga2O3:Sn thin film. These Ga sub-oxide phases are only found in non-transparent films, and so we infer that the Ga sub-oxide is responsible for the non-transparency. These observations suggest that to obtain transparent Ga2O3:Sn, films deposition or subsequent annealing must be carefully controlled in both temperature and oxygen partial pressure to avoid the formation of Ga sub-oxide phases.

  16. Preparation, structure and optical properties of transparent conducting gallium-doped zinc oxide thin films

    Directory of Open Access Journals (Sweden)

    Gu J. H.

    2015-09-01

    Full Text Available Highly conductive gallium-doped zinc oxide (GZO transparent thin films were deposited on glass substrates by RF mag­netron sputtering. The deposited films were characterized by X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, four-point probe and UV-Vis spectrophotometer, respectively. The effect of growth temperature on the structure and optoelectrical properties of the films was investigated. The results demonstrate that high quality GZO films oriented with their crystal­lographic c-axis perpendicular to the substrates are obtained. The structure and optoelectrical properties of the films are highly dependent on the growth temperature. It is found that with increasing growth temperature, the average visible transmittance of the deposited films is enhanced and the residual stress in the thin films is obviously relaxed. The GZO films deposited at the growth temperature of 400°C, which have the largest grain size (74.3 nm, the lowest electrical resistivity (1.31×10-3 Ω·cm and the maximum figure of merit (1.46×1O-2Ω-1, exhibit the best optoelectrical properties. Furthermore, the optical proper­ties of the deposited films were determined by the optical characterization methods and the optical energy-gaps were evaluated by extrapolation method. A blue shift of the optical energy gap is observed with an increase in the growth temperature.

  17. The effect of sub-oxide phases on the transparency of tin-doped gallium oxide

    Science.gov (United States)

    Lim, K.; Schelhas, L. T.; Siah, S. C.; Brandt, R. E.; Zakutayev, A.; Lany, S.; Gorman, B.; Sun, C. J.; Ginley, D.; Buonassisi, T.; Toney, M. F.

    2016-10-01

    There have been a number of studies on the fabrication of Sn-doped gallium oxide (Ga2O3:Sn) films with both conductive and transparent properties using a variety of deposition methods. However, often, synthesis results in films that are not transparent. In this paper, we examine the mechanisms underlying these results in Ga2O3:Sn thin films prepared at various growth temperatures, Sn concentrations, and oxygen partial pressures. With X-ray absorption spectroscopy, transmission electron microscopy and energy dispersive spectroscopy, we find that when films are grown under the oxygen deficient conditions there are Ga sub-oxide and SnOx phases in the Ga2O3:Sn thin film. These Ga sub-oxide phases are only found in non-transparent films, and so we infer that the Ga sub-oxide is responsible for the non-transparency. These observations suggest that to obtain transparent Ga2O3:Sn, films deposition or subsequent annealing must be carefully controlled in both temperature and oxygen partial pressure to avoid the formation of Ga sub-oxide phases.

  18. Platinum nanoparticles on gallium nitride surfaces: effect of semiconductor doping on nanoparticle reactivity.

    Science.gov (United States)

    Schäfer, Susanne; Wyrzgol, Sonja A; Caterino, Roberta; Jentys, Andreas; Schoell, Sebastian J; Hävecker, Michael; Knop-Gericke, Axel; Lercher, Johannes A; Sharp, Ian D; Stutzmann, Martin

    2012-08-01

    Platinum nanoparticles supported on n- and p-type gallium nitride (GaN) are investigated as novel hybrid systems for the electronic control of catalytic activity via electronic interactions with the semiconductor support. In situ oxidation and reduction were studied with high pressure photoemission spectroscopy. The experiments revealed that the underlying wide-band-gap semiconductor has a large influence on the chemical composition and oxygen affinity of supported nanoparticles under X-ray irradiation. For as-deposited Pt cuboctahedra supported on n-type GaN, a higher fraction of oxidized surface atoms was observed compared to cuboctahedral particles supported on p-type GaN. Under an oxygen atmosphere, immediate oxidation was recorded for nanoparticles on n-type GaN, whereas little oxidation was observed for nanoparticles on p-type GaN. Together, these results indicate that changes in the Pt chemical state under X-ray irradiation depend on the type of GaN doping. The strong interaction between the nanoparticles and the support is consistent with charge transfer of X-ray photogenerated free carriers at the semiconductor-nanoparticle interface and suggests that GaN is a promising wide-band-gap support material for photocatalysis and electronic control of catalysis.

  19. Properties of multilayer gallium and aluminum doped ZnO(GZO/AZO)transparent thin films deposited by pulsed laser deposition process

    Institute of Scientific and Technical Information of China (English)

    Jin-Hyum SHIN; Dong-Kyun SHIN; Hee-Young LEE; Jai-Yeoul LEE

    2011-01-01

    Multilayer gallium and aluminum doped ZnO (GZO/AZO) films were fabricated by alternative deposition of Ga-doped zinc oxide(GZO) and Al-doped zinc oxide(AZO) thin film by using pulsed laser deposition(PLD) process. The electrical and optical properties of these GZO/AZO thin films were investigated and compared with those of GZO and AZO thin films. The GZO/AZO GZO/AZO thin films linearly decreases with increasing the Al ratio.

  20. Medical Applications and Toxicities of Gallium Compounds

    Directory of Open Access Journals (Sweden)

    Christopher R. Chitambar

    2010-05-01

    Full Text Available Over the past two to three decades, gallium compounds have gained importance in the fields of medicine and electronics. In clinical medicine, radioactive gallium and stable gallium nitrate are used as diagnostic and therapeutic agents in cancer and disorders of calcium and bone metabolism. In addition, gallium compounds have displayed anti-inflammatory and immunosuppressive activity in animal models of human disease while more recent studies have shown that gallium compounds may function as antimicrobial agents against certain pathogens. In a totally different realm, the chemical properties of gallium arsenide have led to its use in the semiconductor industry. Gallium compounds, whether used medically or in the electronics field, have toxicities. Patients receiving gallium nitrate for the treatment of various diseases may benefit from such therapy, but knowledge of the therapeutic index of this drug is necessary to avoid clinical toxicities. Animals exposed to gallium arsenide display toxicities in certain organ systems suggesting that environmental risks may exist for individuals exposed to this compound in the workplace. Although the arsenic moiety of gallium arsenide appears to be mainly responsible for its pulmonary toxicity, gallium may contribute to some of the detrimental effects in other organs. The use of older and newer gallium compounds in clinical medicine may be advanced by a better understanding of their mechanisms of action, drug resistance, pharmacology, and side-effects. This review will discuss the medical applications of gallium and its mechanisms of action, the newer gallium compounds and future directions for development, and the toxicities of gallium compounds in current use.

  1. POLLUTION PREVENTION IN THE SEMICONDUCTOR INDUSTRY THROUGH RECOVERY AND RECYCLING OF GALLIUM AND ARSENIC FROM GAAS POLISHING WASTES

    Science.gov (United States)

    A process was developed for the recovery of both arsenic and gallium from gallium arsenide polishing wastes. The economics associated with the current disposal techniques utilizing ferric hydroxide precipitation dictate that sequential recovery of toxic arsenic and valuble galliu...

  2. Optical properties of pure and Ce{sup 3+} doped gadolinium gallium garnet crystals and epitaxial layers

    Energy Technology Data Exchange (ETDEWEB)

    Syvorotka, I.I. [Scientific Research Company “Carat”, 202 Stryjska Street, Lviv 79031 (Ukraine); Sugak, D. [Scientific Research Company “Carat”, 202 Stryjska Street, Lviv 79031 (Ukraine); Lviv Polytechnic National University, 12, S. Bandera Street, Lviv, 79013 (Ukraine); Wierzbicka, A. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Wittlin, A. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Cardinal Stefan Wyszyński University in Warsaw, ul. Dewajtis 5, 01-815 Warsaw (Poland); Przybylińska, H. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Barzowska, J. [Institute of Experimental Physics, Gdańsk University, ul. Wita Stwosza 57, Gdańsk (Poland); Barcz, A. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Institute of Electron Technology, Al. Lotników 32/46, 02-668 Warsaw (Poland); Berkowski, M.; Domagała, J. [Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Mahlik, S.; Grinberg, M. [Institute of Experimental Physics, Gdańsk University, ul. Wita Stwosza 57, Gdańsk (Poland); Ma, Chong-Geng [College of Mathematics and Physics, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); and others

    2015-08-15

    Results of X-ray diffraction and low temperature optical absorption measurements of cerium doped gadolinium gallium garnet single crystals and epitaxial layers are reported. In the region of intra-configurational 4f–4f transitions the spectra of the bulk crystals exhibit the signatures of several different Ce{sup 3+} related centers. Apart from the dominant center, associated with Ce substituting gadolinium, at least three other centers are found, some of them attributed to the so-called antisite locations of rare-earth ions in the garnet host, i.e., in the Ga positions. X-ray diffraction data prove lattice expansion of bulk GGG crystals due to the presence of rare-earth antisites. The concentration of the additional Ce-related centers in epitaxial layers is much lower than in the bulk crystals. However, the Ce-doped layers incorporate a large amount of Pb from flux, which is the most probable source of nonradiative quenching of Ce luminescence, not observed in crystals grown by the Czochralski method. - Highlights: • Ce{sup 3+} multicenters found in Gadolinium Gallium Garnet crystals and epitaxial layers. • High quality epitaxial layers of pure and Ce-doped GGG were grown. • Luminescence quenching of Ce{sup 3+} by Pb ions from flux detected in GGG epitaxial layers. • X-ray diffraction allows measuring the amount of the rare-earth antisites in GGG.

  3. Negative permittivity of ZnO thin films prepared from aluminum and gallium doped ceramics via pulsed-laser deposition

    OpenAIRE

    M.A. Bodea; Sbarcea, G.; Naik, Gururaj V.; Boltasseva, Alexandra; Klar, T. A.; Pedarnig, J. D.

    2013-01-01

    Aluminum and gallium doped zinc oxide thin films with negative dielectric permittivity in the near infrared spectral range are grown by pulsed laser deposition. Composite ceramics comprising ZnO and secondary phase Al2O3 or Ga2O3 are employed as targets for laser ablation. Films deposited on glass from dense and small-grained ceramic targets show optical transmission larger than 70 % in the visible and reveal an onset of metallic reflectivity in the near infrared at 1100 nm and a crossover to...

  4. The frequency-domain relaxation response of gallium doped Cd{sub 1-x}Mn{sub x}Te

    Energy Technology Data Exchange (ETDEWEB)

    Trzmiel, Justyna; Weron, Karina [Institute of Physics, Wroclaw University of Technology, Wybrzeze Wyspianskiego 27, 50-370 Wroclaw (Poland); Jurlewicz, Agnieszka [Hugo Steinhaus Center, Institute of Mathematics and Computer Science, Wroclaw University of Technology, Wybrzeze Wyspianskiego 27, 50-370 Wroclaw (Poland)

    2010-03-10

    In this paper the complex dielectric permittivity of gallium doped Cd{sub 0.99}Mn{sub 0.01}Te mixed crystals is studied at different temperatures. We observe a two-power-law relaxation pattern with m and n, the low- and high-frequency power-law exponents respectively, satisfying the relation m < 1 - n. To interpret the empirical result we propose a correlated-cluster relaxation mechanism. This approach allows us to find origins of both power-law exponents, m and n.

  5. Spectral and angular-selective thermal emission from gallium-doped zinc oxide thin film structures

    Science.gov (United States)

    Sakr, Enas; Bermel, Peter

    2017-02-01

    Simultaneously controlling both the spectral and angular emission of thermal photons can qualitatively change the nature of thermal radiation, and offers a great potential to improve a broad range of applications, including infrared light sources and thermophotovoltaic (TPV) conversion of waste heat to electricity. For TPV in particular, frequency-selective emission is necessary for spectral matching with a photovoltaic converter, while directional emission is needed to maximize the fraction of emission reaching the receiver at large separation distances. This can allow the photovoltaics to be moved outside vacuum encapsulation. In this work, we demonstrate both directionally and spectrally-selective thermal emission for p-polarization, using a combination of an epsilon-near-zero (ENZ) thin film backed by a metal reflector, a high contrast grating, and an omnidirectional mirror. Gallium-doped zinc oxide is selected as an ENZ material, with cross-over frequency in the near-infrared. The proposed structure relies on coupling guided modes (instead of plasmonic modes) to the ENZ thin film using the high contrast grating. The angular width is thus controlled by the choice of grating period. Other off-directional modes are then filtered out using the omnidirectional mirror, thus enhancing frequency selectivity. Our emitter design maintains both a high view factor and high frequency selectivity, leading to a factor of 8.85 enhancement over a typical blackbody emitter, through a combination of a 22.26% increase in view factor and a 6.88x enhancement in frequency selectivity. This calculation assumes a PV converter five widths away from the same width emitter in 2D at 1573 K.

  6. Effect of gallium concentrations on the morphologies, structural and optical properties of Ga-doped ZnO nanostructures.

    Science.gov (United States)

    Algarni, H; El-Gomati, M M; Al-Assiri, M S

    2014-07-01

    The effect of gallium ion concentrations (0.5 and 2%) on the morphologies, structural and optical properties of Ga-doped ZnO nanostructures are presented. Ga-doped ZnO nanostructures were synthesized on silicon substrates by simple thermal evaporation process using metallic zinc and Ga powders in the presence of oxygen. Interestingly, it was observed that Ga-ions incorporation in ZnO nanomaterials play an important role on the growth kinetics and hence on the morphologies of as-grown Ga-doped ZnO nanostructures. It was seen that at low Ga-concentration, needle-shaped Ga-doped ZnO nanostructures are formed, presumably by subsequent stacking of hexagonal plates. However, when increasing the Ga-concentration, multipods of Ga-doped ZnO were grown. In addition to the morphologies, incorporating Ga-ions into ZnO also affect the room-temperature photoluminescence properties. Therefore, at lower Ga-ion concentration, an intense UV emission was observed while at high Ga-concentration a deep level emission was seen in the room-temperature photoluminescence spectra. This research demonstrates that by controlling the Ga-ion concentration the morphologies and optical properties of ZnO nanomaterials can be tailored.

  7. Plasmon resonance and perfect light absorption in subwavelength trench arrays etched in gallium-doped zinc oxide film

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, Joshua R., E-mail: joshua.hendrickson.4@us.af.mil; Leedy, Kevin; Cleary, Justin W. [Air Force Research Laboratory, Sensors Directorate, 2241 Avionics Circle, Wright Patterson AFB, Ohio 45433 (United States); Vangala, Shivashankar [Air Force Research Laboratory, Sensors Directorate, 2241 Avionics Circle, Wright Patterson AFB, Ohio 45433 (United States); SURVICE Engineering, 4141 Colonel Glenn Highway, Dayton, Ohio 45431 (United States); Nader, Nima [Air Force Research Laboratory, Sensors Directorate, 2241 Avionics Circle, Wright Patterson AFB, Ohio 45433 (United States); Solid State Scientific Corporation, 12 Simon St., Nashua, New Hampshire 03060 (United States); Guo, Junpeng [Department of Electrical and Computer Engineering, University of Alabama in Huntsville, 301 Sparkman Drive, Huntsville, Alabama 35899 (United States)

    2015-11-09

    Near-perfect light absorption in subwavelength trench arrays etched in highly conductive gallium-doped zinc oxide films was experimentally observed in the mid infrared regime. At wavelengths corresponding to the resonant excitation of surface plasmons, up to 99% of impinging light is efficiently trapped and absorbed in the periodic trenches. Scattering cross sectional calculations reveal that each individual trench acts like a vertical split ring resonator with a broad plasmon resonance spectrum. The coupling of these individual plasmon resonators in the grating structure leads to enhanced photon absorption and significant resonant spectral linewidth narrowing. Ellipsometry measurements taken before and after device fabrication result in different permittivity values for the doped zinc oxide material, indicating that localized annealing occurred during the plasma etching process due to surface heating. Simulations, which incorporate a 50 nm annealed region at the zinc oxide surface, are in a good agreement with the experimental results.

  8. 负电子亲和势砷化镓光阴极热发射度测量%Thermal Emittance Measurement of Negative Electron Affinity Gallium Arsenide Photocathode

    Institute of Scientific and Technical Information of China (English)

    吴岱; 潘清; 肖德鑫; 李凯; 杨仁俊; 王建新; 张海旸

    2015-01-01

    作为未来高平均功率、高亮度电子源的重要材料之一,负电子亲和势砷化镓(NEA‐GaAs)光阴极发射的电子束亮度一直以来都是国际上的研究热点。热发射度是电子束能够实现的发射度下限,测量热发射度有利于确定注入器能否提供高亮度的电子束。本文理论计算了 NEA‐GaAs光阴极热发射度数值范围,并基于中国工程物理研究院自由电子激光相干强太赫兹源(FEL‐T Hz )装置,在28 fC的极低电荷量下,采用螺线管扫描法初步测量了NEA‐GaAs光阴极的热发射度。结果显示,NEA‐GaAs光阴极的热发射度为(0.603±0.002)μm/m m。%As one of the most important high average power electron source materials , the high brightness negative electron affinity (NEA ) gallium arsenide (GaAs) photo‐cathode becomes a researcher focus nowadays .The thermal emittance is the lower limit of emittance ,and its measurement is of great importance to determine the brightness that an injector can provide .In this paper ,based on the terahertz free electron laser (FEL‐T Hz) facility in China Academy of Engineering Physics ,some efforts were made to calculate and measure the thermal emittance of NEA‐GaAs photocathode . Under ultra‐low charge of 28 fC NEA‐GaAs photocathode ,the thermal emittance is (0.603 ± 0.002)μm/mm by the solenoid scan method .

  9. An experimental study of the local electronic structure of B-site gallium doped bismuth ferrite powders

    Science.gov (United States)

    Gholam, Turghunjan; Ablat, Abduleziz; Mamat, Mamatrishat; Wu, Rong; Aimidula, Aimierding; Bake, Muhammad Ali; Zheng, Lirong; Wang, Jiaou; Qian, Haijie; Wu, Rui; Ibrahim, Kurash

    2017-08-01

    The un-doped and gallium (Ga) doped multiferroic bismuth ferrite (BiFeO3) compounds were successfully synthesized by the hydrothermal technique. This is then followed by a series of detailed investigations into the influence of Ga doping on the structural, morphological, optical and magnetic properties of BiFe1 - xGaxO3 (0 ≤ x ≤ 0.15). X-ray diffraction (XRD) analyses reveal that B-site doping of Ga may lead to the transformation of its crystal structure from a rhombohedral with a space group of R3c to an orthorhombic with a space group of Pbnm phase. The scanning electron microscope (SEM) images show that doping with Ga causes a significant reduction in particle size, when compared to un-doped BiFeO3. X-ray absorption near-edge structure (XANES) spectra have also shown that as the substitution of Ga increases, the Fe K and Bi LIII-edge absorption spectra shift towards higher energy site. It also implies that doping of Ga affects the local structures of both Bi and Fe atoms. Distinct transmission band fluctuations, as shown by Fourier transform infrared (FT-IR) spectra, can provide significant evidence for a transformation in crystal structure, following the increase of Ga concentration. The magnetization hysteresis measurements show that the magnetization decreases when Ga content is x ≥ 0.05. Such a phenomenon mainly stems from the substitution of Fe for an excessive amount of Ga, resulting in reduction of both valence fluctuations and the magnetization in the BiFe1 - xGaxO3 system.

  10. Sol-gel deposited aluminum-doped and gallium-doped zinc oxide thin-film transparent conductive electrodes with a protective coating of reduced graphene oxide

    Science.gov (United States)

    Zhu, Zhaozhao; Mankowski, Trent; Balakrishnan, Kaushik; Shikoh, Ali Sehpar; Touati, Farid; Benammar, Mohieddine A.; Mansuripur, Masud; Falco, Charles M.

    2016-04-01

    Using a traditional sol-gel deposition technique, we successfully fabricated aluminum-doped zinc oxide (AZO) and gallium-doped zinc oxide (GZO) thin films on glass substrates. Employing a plasma treatment method as the postannealing process, we produced thin-film transparent conductive electrodes exhibiting excellent optical and electrical properties, with transmittance greater than 90% across the entire visible spectrum and the near-infrared range, as well as good sheet resistance under 200 Ω/sq. More importantly, to improve the resilience of our fabricated thin-film samples at elevated temperatures and in humid environments, we deposited a layer of reduced graphene oxide (rGO) as protective overcoating. The stability of our composite AZO/rGO and GZO/rGO samples improved substantially compared to that of their counterparts with no rGO coating.

  11. a Dlts Study of the EL2 Deep Level in Epitaxial Layers of GALLIUM(1-X) Indium(x) Arsenide Deposited by Mocvd

    Science.gov (United States)

    Lang, Rick

    1990-01-01

    The EL2 deep level is the dominant naturally occurring electron trapping level in metal organic chemical vapour deposited (MOCVD) GaAs. It is also present in ternary alloys such as Ga_{1-x} Al_{x}As, GaAs_{rm 1-x}P _{x} and Ga_ {1-x}In_{ x}As where the changing composition of the crystal lattice alters the local environment of the deep levels. This can influence the properties of the deep level wave functions due to their sensitivity to their immediate environment. In the present work Deep Level Transient Spectroscopy (DLTS) has been employed to measure the thermal activation energy of the EL2 deep level in Ga_{ 1-x}In_{x}As epilayers deposited by low pressure MOCVD onto degenerately doped GaAs substrates. To perform these measurements Au Schottky barrier diodes were fabricated on the epilayers and characterized by Current-Voltage (I -V) and Capacitance-Voltage (C-V) measurements. For some of the samples investigated, the results of these measurements and the DLTS measurements performed using various biasing conditions revealed either back-to-back diode behaviour, or large temperature dependencies for the calculated depletion region widths, or severe bias-sensitive variations in the DLTS spectra. Such behaviours are related to conditions at the Schottky interface and denote that the DLTS results are distorted and unreliable. After elimination of these distorted results, two different dependences of the EL2 thermal activation energy on the indium concentration of the epilayer were apparent. The dependences differed for epilayers deposited using different substrate orientations and V/III reagent ratios during epilayer deposition. For both cases the thermal activation energy decreased with increasing indium concentration in the epilayers. Investigations of the DLTS measurement conditions were made to determine if the differences in the thermal activation energy dependences on the indium concentrations were caused by conditions which are known to influence the

  12. Deep Impurity States in Gallium Arsenide.

    Science.gov (United States)

    1981-10-01

    density of electron states, E, is the ree -eleroi Form. enerry. E, . =(/ 2 ex F, , - > + ! . is the forbidden band gap, and E, is the averave or Penn...Ledebo, J. Appl. Phys. 46, was observed in the bulk sample C. 2155 (1975). 5H.J. Stocker, E. Bauser, and Laurence Schmidt Figure 6 finally shows the

  13. Gallium Arsenide and Related Compounds, 1986.

    Science.gov (United States)

    1986-01-01

    California at Santa Barbara , for his contributions to hot-electron effects, the Gunn Oscillator, and III - V heterojunction devices including the... Caper )o p A11k ’I T~’I N-H Lboratoiets Mimarrai% ill. N.J (;70)71 lh.-.tra1 t ml’.Ii"’i"~t. lh’~t’~’ I)(- it first rt’alizaioni of a t’(’"mmianit... Barbara , CA 93106 J. R. Abelson and T. W. Sigmon Stanford Electronics Laboratories Stanford University, Stanford, CA 94305 Abstract Epitaxial regrowth

  14. Spalling fracture behavior in (100) gallium arsenide

    Science.gov (United States)

    Sweet, Cassi A.

    Record-high conversion efficiencies inherent in III-V solar cells make them ideal for one-sun photovoltaic applications. However, material costs associated with implementation prevent competitive standing with other solar technologies. This dissertation explores controlled exfoliation of III-V single junction photovoltaic devices from (100) GaAs substrates by spalling to enable wafer reuse for material cost reductions. Spalling is a type of fracture that occurs within the substrate of a bilayer under sufficient misfit stress. A spalling crack propagates parallel to the film/substrate interface at a steady-state spalling depth within the substrate. Spalling in (100) GaAs, a semiconductor with anisotropic fracture properties, presents unique challenges. Orientation of the cleavage plane is not parallel to the steady-state spalling depth which results in a faceted fracture surface. A model is developed by modifying Suo and Hutchinson's spalling mechanics to approximate quantitatively the spalling process parameter window and the thickness of the exfoliated film, i.e. spalling depth, for use with (100) GaAs and other semiconductor materials. Experimental data for faceted (100)-GaAs spalling is shown to be in agreement with this model. A faceted surface leads to undesirable waste material for low cost application to the solar industry. Therefore, methods to mitigate the facet size are explored. Trends in facet size and distribution are linked with both the stressor film deposition parameters and the spalling pull velocity. A spalling fracture is a high energy process where damage to the exfoliated material is a concern. Spalled material quality is assessed directly by dislocation density analysis and indirectly by characterization of electrical performance of high quality spalled photovoltaic devices sensitive to material damage such as dislocation and microcrack occurrence. Controlled application of spalling in (100) GaAs is achieved by exfoliation of a high performance single junction solar cell resulting in 18.2% conversion efficiency without the use of an anti-reflective coating. It is shown that spalling in (100) GaAs is a successful device exfoliation process that does not generate defects or cause degradation to device performance.

  15. Phonon heat transport in gallium arsenide

    Indian Academy of Sciences (India)

    Richa Saini; Vinod Ashokan; B D Indu; R Kumar

    2012-03-01

    The lifetimes of quantum excitations are directly related to the electron and phonon energy linewidths of a particular scattering event. Using the versatile double time thermodynamic Green’s function approach based on many-body theory, an ab-initio formulation of relaxation times of various contributing processes has been investigated with newer understanding in terms of the linewidths of electrons and phonons. The energy linewidth is found to be an extremely sensitive quantity in the transport phenomena of crystalline solids as a collection of large number of scattering processes, namely, boundary scattering, impurity scattering, multiphonon scattering, interference scattering, electron–phonon processes and resonance scattering. The lattice thermal conductivities of three samples of GaAs have been analysed on the basis of modified Callaway model and a fairly good agreement between theory and experimental observations has been reported.

  16. Modulation of electrical and optical properties of gallium-doped ZnO films by radio frequency magnetron sputtering

    Institute of Scientific and Technical Information of China (English)

    Liang Shuang; Mei Zeng-Xia; Du Xiao-Long

    2012-01-01

    Ga-doped ZnO (GZO) films are prepared on amorphous glass substrates at room temperature by radio frequency magnetron sputtering.The results reveal that the gallium doping efficiency,which will have an important influence on the electrical and optical properties of the film,can be governed greatly by the deposition pressure and film thickness.The position shifts of the ZnO (002) peaks in X-ray diffraction (XRD) measurements and the varied Hall mobility and carrier concentration confirms this result.The low Hall mobility is attributed to the grain boundary barrier scattering.The estimated height of barrier decreases with the increase of carrier concentration,and the trapping state density is nearly constant.According to defect formation energies and relevant chemical reactions,the photoluminescence (PL)peaks at 2.46 eV and 3.07 eV are attributed to oxygen vacancies and zinc vacancies,respectively.The substitution of more Ga atoms for Zn vacancies with the increase in film thickness is also confirmed by the PL spectrum.The obvious blueshift of the optical bandgap with an increase of carrier concentration is explained well by the Burstein-Moss (BM)effect.The bandgap difference between 3.18 eV and 3.37 eV,about 0.2 eV,is attributed to the metal-semiconductor transition.

  17. The electrical properties of photodiodes based on nanostructure gallium doped cadmium oxide/p-type silicon junctions

    Science.gov (United States)

    Çavaş, M.; Yakuphanoğlu, F.; Karataş, Ş.

    2017-01-01

    Gallium doped cadmium-oxide (CdO: Ga) thin films were successfully deposited by sol-gel spin coating method on p-type Si substrate. The electrical properties of the photodiode based on nanostructure Ga doped n-CdO/p-Si junctions were investigated. The current-voltage (I-V) characteristics of the structure were investigated under various light intensity and dark. It was observed that generated photocurrent of the Au/n-CdO/p-Si junctions depended on light intensity. The capacitance-voltage and conductance-voltage measurements were carried out for this diode in the frequency range between 100 and 1000 kHz at room temperature by steps of 100 kHz. The capacitance decreased with increasing frequency due to a continuous distribution of the interface states. These results suggested that the Au/n-CdO/p-Si Schottky junctions could be utilized as a photosensor. Furthermore, the voltage and frequency dependence of series resistance were calculated from the C-V and G/ω-V measurements and plotted as functions of voltage and frequency. The distribution profile of R S -V gave a peak in the depletion region at low frequencies and disappeared with increasing frequencies.

  18. Electronic structure and optical properties of doped gallium phosphide: A first-principles simulation

    Science.gov (United States)

    Lu, Xuefeng; Gao, Xu; Li, Cuixia; Ren, Junqiang; Guo, Xin; La, Peiqing

    2017-09-01

    Using DFT-GGA-PW91 calculations we investigate the electronic structures and optical properties of doped GaP. It is found that the lattice constants and volume increase slightly for Al, In, As and Sb doped systems and EG distinctly decrease after doping. The formation energies are 0.587 and 0.273 eV for As and Sb doped systems, respectively, and lower remarkably than those in other systems, indicating that the stability of the two systems is higher. The direct band gap transition occurs when doped with In, As and Sb elements. The charge density difference images reveal that electron loss near Al atom is observed accompanying the enhancement of covalent bond feature, and then electron enrichment is present around N atom demonstrating that the ionic bond characteristic is obvious. The Sb-doped system has the higher static dielectric constant illustrating the applications in semiconductor devices. The absorption peak value is located at 194.7 nm for Al-doped system and this shows that the system can absorb a large amount of light and displays ;Barrier-type; characteristics in UV region. In the visible region, the doped systems have lower reflectivity coefficient, indicating that the systems all have ;clear-type; properties. This is conducive to fundamentally insights to a tunable band gap semiconductor with enormous potential in device fields.

  19. Fabrication and characterization of cerium-doped terbium gallium garnet with high magneto-optical properties.

    Science.gov (United States)

    Chen, Zhe; Hang, Yin; Yang, Lei; Wang, Jun; Wang, Xiangyong; Hong, Jiaqi; Zhang, Peixiong; Shi, Chunjun; Wang, Yaqi

    2015-03-01

    High optical quality (Tb((1-x))Ce(x))₃Ga₅O₁₂ (TCGG) single crystal has been grown by the Czochralski method. The optical and magneto-optical properties of the TCGG are analyzed in detail and the Verdet constant (V) of TCGG is compared with that of undoped terbium gallium garnet (TGG) crystal. TCGG presents a very high transmittance, particularly in the visible-near infrared (VIS-NIR) region, and its V is obviously larger than that of TGG in the VIS-NIR region. The figure of merit and optical features point out the superior characteristics of TCGG with respect to TGG.

  20. A modification of Eu incorporation sites by the dissociation of hydrogen defect complexes in Mg co-doped Eu doped gallium nitride

    Science.gov (United States)

    Mitchell, Brandon; Poplawsky, Jonathan; Dierolf, Volkmar

    2013-03-01

    Europium doped gallium nitride (Eu:GaN) is a promising candidate as a material for red LEDs that can monolithically be integrated with existing nitride based lighting technology. Photoluminescence (PL) and cathodoluminescence (CL) studies have revealed, however, that the majority incorporation environment (site) for the Eu is not efficiently excited by electron hole pairs. To improve this efficiency, Mg was co-doped into Eu:GaN during metal organic chemical vapor deposition and multiple new incorporation environments were discovered. These new sites show a high efficiency at room temperature and have been attributed to the coupling of a Mg-H complex to the majority Eu site. However, we also observe that sustained electron beam irradiation produced a semi-permanent change in the CL spectra of the sample. It was demonstrated that this change occurs in two distinct steps which exhibit a pronounced temperature dependence. Our observations point toward a dynamic system in which the Mg-H bond is broken and the hydrogen moves within the epi-layer. Details of this behavior will be discussed.

  1. Surface study of gallium- and aluminum- doped graphenes upon adsorption of cytosine: DFT calculations

    Science.gov (United States)

    Shokuhi Rad, Ali; Zareyee, Daryoush; Peyravi, Majid; Jahanshahi, Mohsen

    2016-12-01

    The adsorption of cytosine molecule on Al- and Ga- doped graphenes is studied using first-principles density functional theory (DFT) calculations. The energetically most stable geometries of cytosine on both Al- and Ga- doped graphenes are determined and the adsorption energies are calculated. The net charge of transfer as well as local charge of doped atoms upon adsorption of cytosine are studied by natural bond orbitals (NBO) analysis. Orbital hybridizing of complexes was searched by frontier molecular orbital theory (FMO), and density of states (DOS). Depending on the side of cytosine, there are four possible sites for its adsorption on doped graphene; denoted as P1, P2, P3, and P4, respectively. The order of binding energy in the case of Al-doped graphene is found as P1 ˃ P4 ˃ P3 ˃ P2. Interestingly, the order in the case of Ga-doped graphene changes to: P4 ∼ P1˃ P3˃ P2. Both surfaces show superior adsorbent property, resulting chemisorption of cytosine, especially at P1 and P4 position configurations. The NBO charge analysis reveals that the charge transfers from Al- and Ga- doped graphene sheets to cytosine. The electronic properties of both surfaces undertake important changes after cytosine adsorption, which indicates notable change in its electrical conductivity.

  2. High-power X- and Ka-band Gallium Nitride Amplifiers with Exceptional Efficiency Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Achieving very high-power amplification with maximum efficiency at X- and Ka-band is challenging using solid-state technology. Gallium Arsenide (GaAs) has been the...

  3. Infrared Response of Impurity Doped Silicon MOSFET’s (IRFET’S): Gold, Indium, and Gallium Doped and Applications

    Science.gov (United States)

    1976-11-01

    cooled to room temperature. The resulting gold concentration of approximately 2 x 10l5 cm-3 corresponds to the results of previous work with bulk silicon...on (100) orientation silicon p-type substrate of 1-2nScm resistivity and doped with a gold concentration of 2 x 101 cm 3 . The gate oxide of the MOSFET...intrinsic and highly resistive even at room temperature. As a consequence the gold-doped devices are of the type NI<NA, or have anI: impurity or gold

  4. Comparative study of highly dense aluminium- and gallium-doped zinc oxide transparent conducting sol–gel thin films

    Indian Academy of Sciences (India)

    Naji Al Dahoudi

    2014-10-01

    Transparent conducting aluminium- and gallium-doped zinc oxide (AZO and GZO) layers have been deposited by spin coating on glass substrates. The coatings have been sintered in air at 450 °C for 30 min and then post-annealed at 350 °C in a reducing atmosphere for 30 min. The electrical, optical and morphological properties of both coatings have been studied and compared. The conventional sols lead to very thin coating, typically 24 nm for a single layer of AZO and 32 nm of GZO with electrical resistivity of 0.72 and 0.35 cm, respectively. The value however, drastically decreases down to a minimum of 2.6 × 10-2 cm for AZO and 1.76 × 10-2 cm for GZO, when five multilayer coatings are made. The origin of these differences is due to the different morphology of the coatings showing different electron scattering process. The GZO sol leads to denser smoother structure (porosity of 5%) layers with an average roughness of 2.76 Å, while the AZO coating is formed by a more porous assembly (porosity of 20%) with an average roughness of 3.46 Å. Both coatings exhibit high transparency ( > 85%) in the visible spectrum range with a slight shift of the absorption energy gap.

  5. DFT study on the adsorption of diethyl, ethyl methyl, and dimethyl ethers on the surface of gallium doped graphene

    Science.gov (United States)

    Shokuhi Rad, Ali; Sani, Emad; Binaeian, Ehsan; Peyravi, Majid; Jahanshahi, Mohsen

    2017-04-01

    In this study, we used density functional theory (DFT) to search on the adsorption properties of three important compounds of ether family; diethyl ether (DEE), ethyl methyl ether (EME), and dimethyl ether (DME) on the surface of Gallium doped graphene (GaG). We used three functionals (B3LYP, wb97xd, and MPW1PW91) for optimization and calculation of adsorption energy. After fully optimization, we scrutinized on the charge allocations on the adsorbed ethers as well as GaG (at the area of interaction) based on natural bond orbitals (NBO). Besides, we have calculated the amount of charge transfer upon adsorption of each analyte. We revel that GaG is an ideal adsorbent for chemisorption of all above-mentioned ethers. There is a little difference between the values of adsorption; -123.5, -120, and -118.3 kJ/mol (based on wb97xd) for DEE, EME, and DME, respectively. We found significant changes in the electronic structure of both adsorbent and adsorbate upon adsorption. Moreover, results of charge analyses confirm GaG is a p-type semiconductor.

  6. Application of gallium nitride nanostructures and nitrogen doped carbon spheres as supports for the hydrogenation of cinnamaldehyde.

    Science.gov (United States)

    Kente, Thobeka; Dube, Sibongile M A; Coville, Neil J; Mhlanga, Sabelo D

    2013-07-01

    This paper reports on the synthesis and use of nanostructures of gallium nitride (GaN NSs) and nitrogen doped carbon spheres (NCSs) as support materials for the hydrogenation of cinnamaldehyde. This study provides the first investigation of GaN as a catalyst support in hydrogenation reactions. The GaN NSs were synthesized via chemical vapour deposition (CVD) in a double stage furnace (750 degrees C) while NCSs were made by CVD in a single stage furnace (950 degrees C) respectively. TEM analysis revealed that the GaN NSs were rod-like with average diameters of 200 nm, while the NCSs were solid with smoother surfaces, and with diameters of 450 nm. Pd nanoparticles (1 and 3% loadings) were uniformly dispersed on acid functionalized GaN NSs and NCS. The Pd nanoparticles had average diameters that were influenced by the type of support material used. The GaN NSs and NCSs were tested for the selective hydrogenation of cinnamaldehyde in isopropanol at 40 and 60 degrees C under atmospheric pressure. A comparative study of the activity of the nanostructured materials revealed that the order of catalyst activity was 3% Pd/GaN > 3% Pd/NCSs > 1% Pd/NCSs > 1% Pd/GaN. However, 100% selectivity to hydrocinnamaldehyde (HCALD) was obtained with 1% Pd/GaN at reasonable conversion rates.

  7. Comments on: 'Gallium-doped ZnO thin films deposited by chemical spray'

    Energy Technology Data Exchange (ETDEWEB)

    Tiburcio-Silver, Arturo [Instituto Tecnologico de Toluca, Department of Electric and Electronic Engineering, Apdo. postal 20, 52172 Metepec 3, Edo. Mexico (Mexico)

    2007-01-23

    In this communication, I will discuss some aspects concerning a paper recently published by H. Gomez et al. on the properties of gallium-doped ZnO thin films deposited by chemical spray methods [H. Gomez, A. Maldonado, M. de la L. Olvera, D.R. Acosta, Sol. Energy Mater. Sol. Cells 87 (2005) 107.]. I believe that there are some wrong considerations of basic principles, some incorrect experimental procedures and inconsistencies on the analysis and throughout the paper. The 'Introduction' reflects some knowledge on the subject, but it seems that the authors of the aforementioned paper use outdated background sources in some cases, and inconsistently apply prior research in others. The 'Experimental procedure' shows some serious lack of knowledge concerning thin films that are potentially applicable as transparent electrodes in photovoltaic devices. In the 'Results and discussion', I found some of the arguments and statements contradictory, mainly when the effects of their vacuum annealing were being discussed. Considerations on the 'Structural properties' are necessary, as they are not appropriate for comparative purposes. Finally, a last point, but not less important than the others, is the 'Conclusions' of the paper. Some suggestions are made below for the improvement of this, and several others, aspects of the paper. (author)

  8. Investigation of the Si doping effect in {beta}-Ga{sub 2}O{sub 3} films by co-sputtering of gallium oxide and Si

    Energy Technology Data Exchange (ETDEWEB)

    Takakura, Kenichiro, E-mail: takakura@kumamoto-nct.ac.jp [Kumamoto National College of Technology, 2659-2 Suya, Koushi, Kumamoto 862-1102 (Japan); Funasaki, Suguru; Tsunoda, Isao; Ohyama, Hidenori [Kumamoto National College of Technology, 2659-2 Suya, Koushi, Kumamoto 862-1102 (Japan); Takeuchi, Daisuke [National Institute of Advanced Industrial Science and Technology, 1-1-1, Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Nakashima, Toshiyuki [Chuo Denshi Kogyo Co. Ltd., 4-3-1 Taishido Setagaya Tokyo 154-0004 (Japan); Shibuya, Mutsuo [Echo Mother, 312-2 Toriko, Nishihara, Aso-gun, Kumamoto 861-2401 (Japan); Murakami, Katsuya [Japan Gas Chemi, 995-1, Futa, Nishihara, Aso-gun, Kumamoto 861-2403 (Japan); Simoen, Eddy [Imec, Kapeldreef 75, B-3001 Leuven (Belgium); Claeys, Cor [Imec, Kapeldreef 75, B-3001 Leuven (Belgium); E. E. Department, KU Leuven, B-3001 Leuven (Belgium)

    2012-08-01

    A transparent electrode of Si doped {beta}-Ga{sub 2}O{sub 3} films for solar cells, flat panel displays and other devices, which consists of chemically abundant and ecological friendly elements of gallium and oxygen, was grown on silicon substrates by RF magnetron sputtering using sintered Ga{sub 2}O{sub 3} and Si target. The Si composition in the {beta}-Ga{sub 2}O{sub 3} film is determined by electron dispersive X-ray spectroscopy. The X-ray photoelectron spectroscopy peak ratio of oxygen over gallium decreases with increasing Si content. It is concluded that Si substitutes for the Ga sites in the {beta}-Ga{sub 2}O{sub 3} film.

  9. Spectral and luminescence properties of gadolinium gallium garnet epitaxial films doped with terbium

    Science.gov (United States)

    Vasil'Eva, N. V.; Randoshkin, V. V.; Kolobanov, V. N.; Kryukova, E. B.; Mikhaĭlin, V. V.; Petrovnin, N. N.; Plotnichenko, V. G.; Pyrkov, Yu. N.; Spasskiĭ, D. A.; Sysoev, N. N.

    2007-03-01

    Gadolinium gallium garnet single-crystal films containing terbium are grown through liquid-phase epitaxy from a supercooled solution melt in the PbO-B2O3 system. The optical absorption spectra in the wavelength range 0.2 10.0 μm and the luminescence spectra excited by synchrotron radiation with energies in the range 3.5 30.0 eV are investigated at temperatures of 10 and 300 K. It is revealed that the optical absorption spectra contain an absorption band with the maximum at a wavelength λ ≈0.260 μm, which corresponds to the spin-allowed electric dipole transition between the electronic configurations 4f 8(7 F 6) → 4f 7(8 S)5d of the Tb3+ ions. The narrow low-intensity absorption bands attributed to the 4f → 4f transitions from the 7 F 6 ground level to the 7 F 0 5 multiplet levels of the Tb3+ ions are observed in the wavelength range 1.7 10.0 μm. In the luminescence spectra measured at a temperature of 10 K, the highest intensity is observed for a band with the maximum at a wavelength λ ≈ 0.544 μm, which is associated with the 5 D 4 → 7 F 5 radiative transition in the Tb3+ ion.

  10. Diffusion in Intrinsic and Highly Doped III-V Semiconductors

    CERN Multimedia

    Stolwijk, N

    2002-01-01

    %title\\\\ \\\\Diffusion plays a key role in the fabrication of semiconductor devices. The diffusion of atoms in crystals is mediated by intrinsic point defects. Investigations of the diffusion behaviour of self- and solute atoms on the Ga sublattice of gallium arsenide led to the conclusion that in intrinsic and n-type material charged Ga vacancies are involved in diffusion processes whereas in p-type material diffusion if governed by charged Ga self-interstitials. Concerning the As sublattice of gallium arsenide there is a severe lack of reliable diffusion data. The few available literature data on intrinsic GaAs are not mutually consistent. A systematic study of the doping dependence of diffusion is completely missing. The most basic diffusion process - self-diffusion of As and its temperature and doping dependence - is practically not known. For GaP a similar statement holds.\\\\ \\\\The aim of the present project is to perform a systematic diffusion study of As diffusion in intrinsic and doped GaAs and in GaP. P...

  11. Role of Ga-doping in iron-gallium alloy clusters

    Institute of Scientific and Technical Information of China (English)

    Tang Pei-Zhe; Liu Hai-Tao; Zhu Jie; Wang Shan-Ying; Duan Wen-Hui

    2012-01-01

    The structural and magnetic properties of Fen-mGam (n =3 ~ 6,m =0 ~ 2; n =13,m =0 ~ 3) alloy clusters have been studied using density functional theory.The substitutional doping is favourable for small clusters with up to six atoms at low Ga concentration and substitutional Ga atoms in 13-atom clusters prefer surface sites.The Ga-doping generally could reduce the energetic stability but enhance the electronic stability of Fe clusters,along with a decrease of the local magnetic moments of Fe atoms around Ga dopants.These findings provide a microscopic insight into Fe-Ga alloys which are well-known magnetostriction materials.

  12. Gallium-doped indium oxide nanoleaves: Structural characterization, growth mechanism and optical properties

    Science.gov (United States)

    Liu, Lizhu; Chen, Yiqing; Guo, Linliang; Guo, Taibo; Zhu, Yunqing; Su, Yong; Jia, Chong; Wei, Meiqin; Cheng, Yinfen

    2011-11-01

    The novel two-dimensional (2-D) Ga-doped In2O3 nanoleaves are synthesized by a simple one-step carbonthermal evaporation method using Cu-Sn alloy as the substrates. Two basic parts construct this leaf-like nanostructure: a long central trunk and two tapered nanoribbons in symmetric distribution in relation to the trunk. The Ga-In-O alloy particles are located at or close to the tips of the central trunks and serve as catalysts for the central trunk growth by the self-catalytic vapor-liquid-solid (VLS) mechanism. And the homoepitaxial growth of tapered nanoribbon on the surface of the central trunk can be explained by vapor-solid (VS) mechanism. The room-temperature photoluminescence (PL) measurement of this nanoscaled Ga-doped In2O3 transparent conducting oxide (TCO) detected two blue peaks located at 432 nm and 481 nm, respectively, which can be used by Ru-based dye and indicates potential application in dye-sensitized solar cells (DSSCs). The successful preparation of this novel 2-D Ga-doped In2O3 nanoleaves not only enriches the synthesis of TCO materials, but also provides new blocks in future architecture of functional nano-devices.

  13. Synergistic effect of Indium and Gallium co-doping on growth behavior and physical properties of hydrothermally grown ZnO nanorods

    Science.gov (United States)

    Lim, Jun Hyung; Lee, Seung Muk; Kim, Hyun-Suk; Kim, Hyun You; Park, Jozeph; Jung, Seung-Boo; Park, Geun Chul; Kim, Jungho; Joo, Jinho

    2017-01-01

    We synthesized ZnO nanorods (NRs) using simple hydrothermal method, with the simultaneous incorporation of gallium (Ga) and indium (In), in addition, investigated the co-doping effect on the morphology, microstructure, electronic structure, and electrical/optical properties. The growth behavior of the doped NRs was affected by the nuclei density and polarity of the (001) plane. The c-axis parameter of the co-doped NRs was similar to that of undoped NRs due to the compensated lattice distortion caused by the presence of dopants that are both larger (In3+) and smaller (Ga3+) than the host Zn2+ cations. Red shifts in the ultraviolet emission peaks were observed in all doped NRs, owing to the combined effects of NR size, band gap renormalization, and the presence of stacking faults created by the dopant-induced lattice distortions. In addition, the NR/p-GaN diodes using co-doped NRs exhibited superior electrical conductivity compared to the other specimens due to the increase in the charge carrier density of NRs and the relatively large effective contact area of (001) planes. The simultaneous doping of In and Ga is therefore anticipated to provide a broader range of optical, physical, and electrical properties of ZnO NRs for a variety of opto-electronic applications. PMID:28155879

  14. Effect of nitrogen doping on the structural, optical and electrical properties of indium tin oxide films prepared by magnetron sputtering for gallium nitride light emitting diodes

    Science.gov (United States)

    Tian, Lifei; Cheng, Guoan; Wang, Hougong; Wu, Yulong; Zheng, Ruiting; Ding, Peijun

    2017-01-01

    The indium tin oxide (ITO) films are prepared by the direct current magnetron sputtering technology with an ITO target in a mixture of argon and nitrogen gas at room temperature. The blue transmittance at 455 nm rises from 63% to 83% after nitrogen doping. The resistivity of the ITO film reduces from 4.6 × 10-3 (undoped film) to 5.7 × 10-4 Ω cm (N-doped film). The X-ray photoelectron spectroscopy data imply that the binding energy of the In3d5/2 peak is declined 0.05 eV after nitrogen doping. The high resolution transmission electron microscope images show that the nitrogen loss density of the GaN/ITO interface with N-doped ITO film is smaller than that of the GaN/ITO interface with undoped ITO film. The forward turn-on voltage of gallium nitride light emitting diode reduces by 0.5 V after nitrogen doping. The fabrication of the N-doped ITO film is conducive to modify the N component of the interface between GaN and ITO layer.

  15. Fe-doping in hydride vapor-phase epitaxy for semi-insulating gallium nitride

    Science.gov (United States)

    Richter, E.; Gridneva, E.; Weyers, M.; Tränkle, G.

    2016-12-01

    Fe-doping of GaN layers of 3 in. in diameter and a thickness of 1 mm in a vertical AIX-HVPE reactor is studied. Ferrocen was used as Fe source. It is shown that a sufficient uniformity of growth conditions, a high purity of undoped GaN layers, and a moderate Fe incorporation of 2×1018 cm-3 allow for growth of semi-insulating GaN layers with a sufficiently high specific resistivity even at elevated temperature. This makes the material suitable as substrate for electronic power devices at high power or in harsh ambient.

  16. Synthesis and optical properties of CsC1-doped gallium-sodium-sulfide glasses

    Energy Technology Data Exchange (ETDEWEB)

    Hehlen, Markus P [Los Alamos National Laboratory; Bennett, Bryan L [Los Alamos National Laboratory; Williams, Darrick J [Los Alamos National Laboratory; Muenchausen, Ross E [Los Alamos National Laboratory; Castro, Alonso [Los Alamos National Laboratory; Tornga, Stephanie C [Los Alamos National Laboratory

    2009-01-01

    Ga{sub 2}S{sub 3}-Na{sub 2}S (GNS) glasses doped with CsCl were synthesized in open crucibles under inert atmosphere. The evaporative loss of CsCl during glass melting was measured by energy dispersive X-ray spectroscopy and corrected for by biasing the CsCl concentration in the mixture of starting materials to obtain glasses with accurately controlled stoichiometry. Glass transition temperatures, refractive index dispersions, and band edge energies were measured for four GNS:CsCl glasses, and the respective values were found to significantly improve over earlier studies that did not mitigate CsCl evaporative losses. The refractive index dispersion measurements indicate that the Cs{sup +} and Cl{sup -} radii are 16% larger in GNS:CsCl glass than in bulk crystalline CsCl. The band edge energy increases from 2.97 eV in GNS glass to 3.32 eV in GNS glass doped with 20 mol% CsCl as a result of introducing Cl{sup -} ions having a large optical electronegativity. The large bandgap of 3.32 eV and the low (450 cm{sup -1}) phonon energy make GNS:20%CsCl an attractive host material for rare-earth ions with radiative transitions in the near ultra-violet, visible, and near-infrared spectral regions.

  17. Selective excitation of the yellow and blue luminescence in n- and p-doped Gallium Nitride

    CERN Document Server

    Colton, J S

    2000-01-01

    doping-related potential fluctuations and disorder. Characteristics of the our model for the BL include (a) an Urbach tail, having width E sub 0 = 33 meV, (b) a strong electron-LO phonon coupling occurring with a Frank-Condon shift of approx 180 meV between excitation and emission, (c) a mobility gap at 2.8 eV, separating highly mobile states and highly localized states, and (d) PL-like behavior for excitation energies larger than 2.8 eV, having a blue-shift with increasing excitation energy caused by the increased number of free carriers in the material. GaN is an interesting material: technologically very useful, but still having many unexplained features. Two such features are the broad defect-related luminescence bands: the YL of n-type GaN and the BL of Mg-doped p-type GaN. We have employed selective excitation to investigate these bands. In the case of the YL, most of the previous evidence has supported a recombination model between distant donors and acceptors, most likely a transition involving a shal...

  18. A full free spectral range tuning of p-i-n doped Gallium Nitride microdisk cavity

    CERN Document Server

    Niu, Nan; Aharonovich, Igor; Russell, Kasey J; Woolf, Alexander; Sadler, Thomas C; El-Ella, Haitham A R; Kappers, Menno J; Oliver, Rachel A; Hu, Evelyn L

    2012-01-01

    Effective, permanent tuning of the whispering gallery modes (WGMs) of p-i-n doped GaN microdisk cavity with embedded InGaN quantum dots over one free spectral range is successfully demonstrated by irradiating the microdisks with a ultraviolet laser (380nm) in DI water. For incident laser powers between 150 and 960 nW, the tuning rate varies linearly. Etching of the top surface of the cavity is proposed as the driving force for the observed shift in WGMs, and is supported by experiments. The tuning for GaN/InGaN microdisk cavities is an important step for deterministically realizing novel nanophotonic devices for studying cavity quantum electrodynamics.

  19. Spectroscopic data of the 1.8-, 2.9-, and 4.3- mu m transitions in dysprosium-doped gallium lanthanum sulfide glass

    Science.gov (United States)

    Schweizer, T.; Hewak, D. W.; Samson, B. N.; Payne, D. N.

    1996-10-01

    Infrared emission at 1.8, 2.9, and 4.3 mu m is measured in dysprosium-doped gallium lanthanum sulfide (Ga:La:S) glass excited at 815 nm. Emission cross sections were calculated by Judd-Ofelt analysis, the Fuchtbauer-Ladenburg equation, and the theory of McCumber. The sigma tau value for the 4.3- mu m transition is \\similar 4000 times larger in the Ga:La:S glass than in a dysprosium-doped LiYF4 crystal, which has lased on this transition. The large sigma tau value and the recently reported ability of Ga:La:S glass to be fabricated into fiber form show the potential for an efficient, low-threshold mid-infrared fiber laser. The fluorescence peak at 4.3 mu m coincides with the fundamental absorption of atmospheric carbon dioxide, making the glass a potential laser source for gas-sensing applications.

  20. Spectroscopic data of the 1.8-, 2.9-, and 4.3-microm transitions in dysprosium-doped gallium lanthanum sulfide glass.

    Science.gov (United States)

    Schweizer, T; Hewak, D W; Samson, B N; Payne, D N

    1996-10-01

    Infrared emission at 1.8, 2.9, and 4.3 microm is measured in dysprosium-doped gallium lanthanum sulfide (Ga:La:S) glass excited at 815 nm. Emission cross sections were calculated by Judd-Ofelt analysis, the Füchtbauer- Ladenburg equation, and the theory of McCumber. The sigmatau value for the 4.3-microm transition is ~4000 times larger in the Ga:La:S glass than in a dysprosium-doped LiYF(4) crystal, which has lased on this transition. The large sigmatau value and the recently reported ability of Ga:La:S glass to be fabricated into fiber form show the potential for an efficient, low-threshold mid-infrared fiber laser. The f luorescence peak at 4.3 microm coincides with the fundamental absorption of atmospheric carbon dioxide, making the glass a potential laser source for gas-sensing applications.

  1. Selective excitation of the yellow and blue luminescence in n- and p-doped Gallium Nitride

    Energy Technology Data Exchange (ETDEWEB)

    Colton, John Synder [Univ. of California, Berkeley, CA (United States)

    2000-12-01

    GaN is an interesting material: technologically very useful, but still having many unexplained features. Two such features are the broad defect-related luminescence bands: the YL of n-type GaN and the BL of Mg-doped p-type GaN. We have employed selective excitation to investigate these bands. In the case of the YL, most of the previous evidence has supported a recombination model between distant donors and acceptors, most likely a transition involving a shallow donor to a deep acceptor. Our selective excitation experiments have resolved finer structures within the YL. Our results indicate that the YL in bulk samples is related to the YL in film samples. We suggest that selectively excited YL involves recombination at DAP complexes, rather than between spatially distant DAPs (however other recombination channels, including that of distant DAPs may become significant under other excitation conditions). Characteristics of the DAP complexes within our YL model include (a) an electron localization energy of around 60-70 meV, (b) a localized phonon energy of around 40 meV, and (c) excited states of the complex at 200 and 370 meV above the ground state. In the case of the BL, the deep defect responsible for the BL is unknown, and there may not even be a deep defect involved. Also in dispute is the role of potential fluctuations in the properties of the BL. Our results have been explain in a model whereby emission is from DAPs, and significant effects are produced by doping-related potential fluctuations and disorder. Characteristics of the our model for the BL include (a) an Urbach tail, having width E{sub 0} = 33 meV, (b) a strong electron-LO phonon coupling occurring with a Frank-Condon shift of {approx} 180 meV between excitation and emission, (c) a mobility gap at 2.8 eV, separating highly mobile states and highly localized states, and (d) PL-like behavior for excitation energies larger than 2.8 eV, having a blue-shift with increasing excitation energy caused by the

  2. Efficient injection of spin-polarized electrons from manganese arsenide contacts into aluminum gallium arsenide/gallium arsenide spin LEDs

    Science.gov (United States)

    Schweidenback, Lars

    In this thesis we describe two spectroscopic projects project on semiconductor heterostructures, as well as putting together and testing a micro-photoluminescence/7 tesla magnet system for the study of micron size two-dimensional crystals. Below we discuss the three parts in more detail. i) MnAs-based spin light emitting diodes. We have studied the injection of spin-polarized electrons from a ferromagnetic MnAs contact into an AlGaAs(n)/GaAs(i)/AlGaAs(p) n-i-p light emitting diode. We have recorder the emitted electroluminescence as function of magnetic field applied at right angles to the device plane in the 7-300 K temperature range. It was found that at 7 Kelvin the emitted light is circularly polarized with a polarization that is proportional to the MnAs contact magnetization with a saturation value of 26% for B > 1.25 tesla. The polarization persists up to room temperature with a saturation value of 6%. ii) Optical Aharonov-Bohm effect in InGaAs quantum wells. The excitonic photoluminescence intensity from InGaAs quantum wells as function of magnetic field exhibits two local maxima superimposed on a decreasing background. The maxima are attributed to the optical Aharonov-Bohm effect of electrons orbiting around a hole localized at the center of an Indium rich InGaAs islands detected by cross sectional scanning tunneling microscopy. Analysis of the position of the maxima yields a value of the electron orbit radius. iii) Micro-Photoluminescence. We have put together a micro-photoluminescence /7 tesla system for the study of two dimensional crystals. The samples are placed inside a continuous flow cryostat whose tail is positioned in the bore of the 7 tesla magnet. A microscope objective is used to focus the exciting laser light and collect the emitted photoluminescence. The system was tested by recording the photoluminescence spectra of WS2 and WSe 2 monolayers at T = 77 K.

  3. Ceramics and amorphous thin films based on gallium sulphide doped by rare-earth sulphides

    Science.gov (United States)

    Popescu, M.; Sava, F.; Lőrinczi, A.; Velea, A.; Simandan, I. D.; Badica, P.; Burdusel, M.; Galca, A. C.; Matei, E.; Preda, N.; Secu, M.; Socol, G.; Jipa, F.; Zamfirescu, M.; Balan, A.

    2015-04-01

    Bulk ceramics of Ga2S3 and rare-earth sulfides (EuS, Gd2S3, Er2S3) as well as combinations thereof have been prepared by spark plasma sintering (SPS). The disk-shaped ceramics were used as targets for pulsed laser deposition (PLD) experiments to obtain amorphous thin films. The properties of these new bulks and amorphous thin films have been investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDX), optical transmission spectroscopy, and atomic force microscopy (AFM). In order to test the photoexpansion effect in Ga2S3 and the possibility to create planar arrays of microlenses, the film was irradiated with femtosecond laser pulses at different powers. For low laser power pulses (up to 100 mW power per pulse) a photoexpansion effect was observed, which leads to formation of hillocks with a height of 40-50 nm. EuS doped Ga2S3 thin film shows luminescence properties, which recommend them for optoelectronic applications.

  4. Evolution of magnetic and superconducting phases with doping and pressure in the underdoped iron-arsenide superconductor Ba{sub 1-x}K{sub x}Fe{sub 2}As{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Hassinger, Elena [Universite de Sherbrooke, Quebec (Canada); Canadian Institute for Advanced Research, Toronto, Ontario (Canada); Max Planck Institut fuer Chemische Physik fester Stoffe, Dresden (Germany); Gredat, Gregory; Valade, Fabrice; Rene de Cotret, Samuel; Juneau-Fecteau, Alexandre; Reid, Jean-Philippe; Doiron-Leyraud, Nicolas [Universite de Sherbrooke, Quebec (Canada); Kim, H.; Tanatar, Makariy A.; Prozorov, Ruslan [Ames Laboratory, Ames, Iowa (United States); Shen, B.; Wen, H.H. [Nanjing University (China); Taillefer, Louis [Universite de Sherbrooke, Quebec (Canada); Canadian Institute for Advanced Research, Toronto, Ontario (Canada)

    2015-07-01

    The electrical resistivity ρ of the iron-arsenide superconductor Ba{sub 1-x}K{sub x}Fe{sub 2}As{sub 2} was measured in applied pressures up to 2.75 GPa for seven underdoped samples. Six of them are antiferromagnetic at P = 0 with 0.16 < x < 0.24 and one is non-magnetic with x = 0.26. The stripe-like antiferromagnetic ordering temperature T{sub N}, detected as a sharp anomaly in ρ(T), decreases linearly with pressure. For every magnetic sample a second phase appears with pressure at a lower temperature T{sub 0}, which rises with pressure. The critical pressure above which this phase appears decreases with doping going to zero for x = 0.24 just below the critical doping for the magnetic phase. This behaviour is reminiscent of the second magnetic phase appearing in Ba{sub 0.76}Na{sub 0.24}Fe{sub 2}As{sub 2} where the tetragonal symmetry is restored in favour of the scenario in which the nematic order in the iron pnictides is of magnetic origin.

  5. Uso do laser arseneto de gálio (904nm após excisão artroplástica da cabeça do fêmur em cães Use of low-power gallium arsenide laser (904nm after arthroplasty excision of the femoral head in dogs

    Directory of Open Access Journals (Sweden)

    Julia Maria Matera

    2003-03-01

    Full Text Available OBJETIVO: Avaliar a ação do laser diodo Arseneto de Gálio na evolução pós-operatória de cães submetidos à excisão artroplástica da cabeça e colo do fêmur. MÉTODOS: Treze cães portadores de Legg-Calvé-Perthes Disease ou Necrose Asséptica da Cabeça do Fêmur (NACF foram divididos em dois grupos: (I sete cães que não foram irradiados - grupo controle; (II seis cães irradiados uma vez ao dia durante cinco dias consecutivos com o laser Arseneto de Gálio (904nm, densidade de energia 4J/cm2 e tempo de exposição automaticamente ajustado pelo aparelho. Para a avaliação da evolução pós-operatória preencheu-se protocolo com graduação da dor de apoio do membro operado. Utilizou-se teste estatístico não paramétrico U de Mann-Whitney para análise dos resultados. RESULTADOS: O grupo I iniciou o apoio do membro com uma média de 12 dias de pós-operatório e o grupo II com uma média de quatro dias de pós-operatório, sendo estatisticamente significante (p=0.0012. CONCLUSÃO: A irradiação com o laser de baixa potência Arseneto de Gálio (904nm na dose 4J/cm2, periarticular, promoveu rápido retorno da função do membro em cães após a excisão artroplástica da cabeça do fêmur, otimizando a recuperação pós-operatória.PURPOSE: Evaluate the action of the Gallium Arsenide semiconductor laser in the post-operative evolution in dogs after the femoral head and neck artroplastic excision. METHODS: Thirteen dogs bearing Legg-Calvé-Perthes Disease were divided into two groups: (I 7 non-radiated dogs - control group; (II 6 dogs irradiated once a day for 5 consecutive days with the Galium Arsenide laser (904nm, energy density 4J/cm² and exposition time automatically adjusted by the device. In order to evaluate the post-operative evolution it was needed to fill a report stating the degree of the pain as well as the weight bearing of the affected limb. A U non-parametric statistics test of Mann-Whitney was used to perform

  6. Clinical evaluation of dentin hypersensitivity treatment with the low intensity Gallium-Aluminum-Arsenide laser - AsGaAl Avaliação clínica do tratamento da hiperestesia dentinária com laser de baixa potência de Arseniato de Gálio-Alumínio - AsGaAl

    Directory of Open Access Journals (Sweden)

    Luciana Chucre Gentile

    2004-12-01

    Full Text Available The dentin hypersensitivity is a painful condition rather prevalent in the general population. There are several ways of treatment for such condition, including the low intensity lasers. The proposal of this study was to verify the effectiveness of the Gallium-Aluminum-Arsenide diode laser in the treatment of this painful condition, using a placebo as control. MATERIALS AND METHODS: Thirty-two patients were selected, 22 females and 10 males, with ages ranging from 20 to 52 years old. The 32 patients were randomly distributed into two groups, treated and control; the sample consisted of 68 teeth, 35 in the treated group and 33 in the control group. The treated group was exposed to six laser applications with intervals from 48 to 72 hours, and the control group received, as placebo, applications of a curing light. RESULTS: A significant reduction was observed in the pain condition between the initial phase and after six laser applications; however, such reduction could also be observed for the control group exposed to the placebo. CONCLUSION: Therapy with the low intensity Gallium-Aluminum-Arsenide laser - AsGaAl induces a statistically significant reduction in the painful condition after each application and between the beginning and end of treatment, although there was no statistically significant difference between the treated group (laser and the control group (placebo at the end of treatment and after the mediate evaluation results (after 6 weeks, this way impairing the real measurement of laser effectiveness and placebo effect.A hiperestesia dentinária trata-se de uma condição dolorosa bastante prevalente nas populações mundiais. Várias são as modalidades de tratamento para tal condição, entre elas, os lasers de baixa potência. A proposta deste estudo foi a de verificar a efetividade do laser de diodo de Arseniato de Gálio-Alumínio no tratamento desta condição dolorosa, utilizando-se um placebo como controle. MATERIAIS E M

  7. Development of anode material based on La-substituted SrTiO{sub 3} perovskites doped with manganese and/or gallium for SOFC

    Energy Technology Data Exchange (ETDEWEB)

    Escudero, M.J. [Dpto Energia, CIEMAT, Av. Complutense 22, 28040 Madrid (Spain); School of Chemistry, Purdie Building, University of St Andrews, St Andres, Fife KY16 9ST (United Kingdom); Irvine, J.T.S. [School of Chemistry, Purdie Building, University of St Andrews, St Andres, Fife KY16 9ST (United Kingdom); Daza, L. [Dpto Energia, CIEMAT, Av. Complutense 22, 28040 Madrid (Spain); Instituto de Catalisis y Petroleoquimica (CSIC), Campus Cantoblanco, C/Marie Curie 2, 28049 Madrid (Spain)

    2009-07-01

    Materials based on La-substituted SrTiO{sub 3} perovskites doped with manganese and/or gallium for SOFC have been studied as novel anodes for solid oxide fuel cell. La{sub 4}Sr{sub 8}Ti{sub 11}Mn{sub 1-x}Ga{sub x}O{sub 38-{delta}} (0 {<=} x {<=} 1) oxides were synthesized by solid state reaction and the influences of the manganese and/or gallium content on the structure, morphology, thermal properties and electrical conductivity of these materials has been investigated. All compounds show cubic structure with a space group Pm-3m. These compounds presented high electrical conductivity values under reducing atmosphere between 7.9 and 6.8 S cm{sup -1} at 900 C. For the composition x {>=} 0.5, the thermal expansion coefficient in both reducing and oxidizing atmosphere are close to that of SOFC electrolytes (8YSZ, CGD). In general, the substitution of Ga by Mn causes a slight reduction in each of the following, lattice parameter, degree of oxygen loss on reduction, thermal expansion coefficient, and electrical conductivity. (author)

  8. Effect of gallium doping on the magnetocaloric effect of LaFe11.2Co0.7Si1.1

    Institute of Scientific and Technical Information of China (English)

    DENG Jianqiu; CHEN Xiang; ZHUANG Yinghong

    2008-01-01

    The lattice parameter and magnetocaloric properties of three samples of LaFe11.2Co0.7Si1.1-xGax with x = 0,0.03 and 0.05 have been investigated by X-ray powder diffraction and magnetization measurements.The lattice parameter increases slightly and the Curie temperature increases somewhat with increasing gallium content.However,a small amount of Ga doping into the sample decreases the magnetic entropy change of the sample.All the samples remain in the first-order magnetic phase transition.The most striking effect of the Ga doping is that the cooling capacity in the samples increases significantly.The maximum magnetic entropy change,-△SM,max,and the cooling capacity of the sample LaFe11.2Co0.7Si1.07Ga0.03 are 11.9 J·kg-1.K-1 and 254.8 J.kg-1,respectively.

  9. GROWTH, MORPHOLOGICAL, STRUCTURAL, ELECTRICAL AND OPTICAL PROPERTIES OF NITROGEN DOPED ZINC OXIDE THIN FILM ON POROUS GALLIUM NITRIDE TEMPLATE

    OpenAIRE

    2016-01-01

    Gallium nitride (GaN) is susceptible of producing efficient display and lighting devices.  Low cost hybrid heterostructured lighting devices are developed by combining zinc oxide (ZnO) with GaN that has gained much more research interest, nowadays.  Porous GaN receives a great deal of attraction by its excellent and improved properties compared with its bulk counterpart.  Several potential applications have been realized, including for serving as a strain-relaxed substrates for...

  10. Optical and Surface Characteristics of Mg-Doped GaAs Nanocrystalline Thin Film Deposited by Thermionic Vacuum Arc Technique

    Science.gov (United States)

    Pat, Suat; Özen, Soner; Şenay, Volkan; Korkmaz, Şadan

    2017-01-01

    Magnesium (Mg) is the most promising p-type dopant for gallium arsenide (GaAs) semiconductor technology. Mg-doped GaAs nanocrystalline thin film has been deposited at room temperature by the thermionic vacuum arc technique, a rapid deposition method for production of doped GaAs material. The microstructure and surface and optical properties of the deposited sample were investigated by x-ray diffraction analysis, scanning electron microscopy, energy-dispersive x-ray spectroscopy, atomic force microscopy, ultraviolet-visible spectrophotometry, and interferometry. The crystalline direction of the deposited sample was determined to be (220) plane and (331) plane at 44.53° and 72.30°, respectively. The Mg-doped GaAs nanocrystalline sample showed high transmittance.

  11. Enhanced current transport and injection in thin-film gallium-nitride light-emitting diodes by laser-based doping.

    Science.gov (United States)

    Kim, Su Jin; Kim, Kyeong Heon; Chung, Ho Young; Shin, Hee Woong; Lee, Byeong Ryong; Jeong, Tak; Park, Hyung Jo; Kim, Tae Geun

    2014-10-08

    This paper reports improvements in the electrical and optical properties of blue-emission gallium nitride (GaN)-based thin-film light-emitting diodes (TFLEDs) after laser-based Si doping (LBSD) of a nitrogen-face n-GaN (denoted as hereafter n-GaN) layer. Experimental results show that the light-output powers of the flat- and rough-surface TFLEDs after LBSD are 52.1 and 11.35% higher than those before LBSD, respectively, at a current of 350 mA, while the corresponding operating voltages are decreased by 0.22 and 0.28 V for the flat- and rough-surface TFLEDs after LBSD, respectively. The reduced operating voltage after LBSD of the top n-GaN layer may result from the remarkably decreased specific contact resistance at the metal/n-GaN interface and the low series resistance of the TFLED device. The LBSD of n-GaN increases the number of nitrogen vacancies, and Si substitutes for Ga (SiGa) at the metal/n-GaN interface to produce highly Si-doped regions in n-GaN, leading to a decrease in the Schottky barrier height and width. As a result, the specific contact resistances are significantly decreased to 1.56 × 10(-5) and 2.86 × 10(-5) Ω cm(2) for the flat- and rough-surface samples after LBSD, respectively. On the other hand, the increased light-output power after LBSD can be explained by the uniform current spreading, efficient current injection, and enhanced light scattering resulting from the low contact resistivity, low lateral current resistance, and additional textured surface, respectively. Furthermore, LBSD did not degrade the electrical properties of the TFLEDs owing to low reverse leakage currents. The results indicate that our approach could potentially enable high-efficiency and high-power capabilities for optoelectronic devices.

  12. Low temperature synthesis of radio frequency magnetron sputtered gallium and aluminium co-doped zinc oxide thin films for transparent electrode fabrication

    Science.gov (United States)

    Muchuweni, E.; Sathiaraj, T. S.; Nyakotyo, H.

    2016-12-01

    Gallium and aluminium co-doped zinc oxide (GAZO) thin films were prepared on glass substrates at low temperatures by radio frequency (rf) magnetron sputtering and their physical properties were investigated. All films possessed a hexagonal wurtzite crystal structure with a strong growth orientation along the (0 0 2) c-axis. The (0 0 2) peak intensity and mean crystallite size increased with substrate temperature from room temperature (RT) to 75 °C and then decreased at 100 °C, indicating an improvement in crystallinity up to 75 °C and its deterioration at 100 °C. Scanning electron microscopy (SEM) micrographs revealed the strong dependency of surface morphology on substrate temperature and energy dispersive spectroscopy (EDS) confirmed the incorporation of Ga and Al into the ZnO films. All films exhibited excellent transmittances between 85 and 90% in the visible region and their optical band gap increased from 3.22 eV to 3.28 eV with substrate temperature. The Urbach energy decreased from 194 meV to 168 meV with increasing substrate temperature, indicating a decrease in structural disorders which was consistent with X-ray Diffraction (XRD) analysis. Films deposited at 75 °C exhibited the lowest electrical resistivity (2.4 Ωcm) and highest figure of merit (7.5 × 10-5 Ω-1), proving their potential as candidates for transparent electrode fabrication.

  13. Thermal effects from modified endodontic laser tips used in the apical third of root canals with erbium-doped yttrium aluminium garnet and erbium, chromium-doped yttrium scandium gallium garnet lasers.

    Science.gov (United States)

    George, Roy; Walsh, Laurence J

    2010-04-01

    To evaluate the temperature changes occurring on the apical third of root surfaces when erbium-doped yttrium aluminium garnet (Er:YAG) and erbium, chromium-doped yttrium scandium gallium garnet (Er,Cr:YSGG) laser energy was delivered with a tube etched, laterally emitting conical tip and a conventional bare design optical fiber tip. Thermal effects of root canal laser treatments on periodontal ligament cells and alveolar bone are of concern in terms of safety. A total of 64 single-rooted extracted teeth were prepared 1 mm short of the working length using rotary nickel-titanium Pro-Taper files to an apical size corresponding to a F5 Pro-Taper instrument. A thermocouple located 2 mm from the apex was used to record temperature changes arising from delivery of laser energy through laterally emitting conical tips or plain tips, using an Er:YAG or Er,Cr:YSGG laser. For the Er:YAG and Er,Cr:YSGG systems, conical fibers showed greater lateral emissions (452 + 69% and 443 + 64%) and corresponding lower forward emissions (48 + 5% and 49 + 5%) than conventional plain-fiber tips. All four combinations of laser system and fiber design elicited temperature increases less than 2.5 degrees C during lasing. The use of water irrigation attenuated completely the thermal effects of individual lasing cycles. Laterally emitting conical fiber tips can be used safely under defined conditions for intracanal irradiation without harmful thermal effects on the periodontal apparatus.

  14. 0.15-micron Gallium Nitride (GaN) Microwave Integrated Circuit Designs Submitted to TriQuint Semiconductor for Fabrication

    Science.gov (United States)

    2012-09-01

    arsenide GaN gallium nitride LNA low-noise amplifier MMIC monolithic microwave integrated circuit PA power amplifier HEMT high electron mobility...0.15-µm Gallium Nitride ( GaN ) Microwave Integrated Circuit Designs Submitted to TriQuint Semiconductor for Fabrication by John Penn ARL...MD 20783-1197 ARL-TN-0496 September 2012 0.15-µm Gallium Nitride ( GaN ) Microwave Integrated Circuit Designs Submitted to TriQuint

  15. Nonlinear absorption coefficient and relative refraction index change for an asymmetrical double δ-doped quantum well in GaAs with a Schottky barrier potential

    Energy Technology Data Exchange (ETDEWEB)

    Rojas-Briseño, J.G.; Martínez-Orozco, J.C.; Rodríguez-Vargas, I. [Unidad Académica de Física, Universidad Autónoma de Zacatecas, Calzada Solidaridad esquina con Paseo la Bufa S/N, C.P. 98060, Zacatecas, Zac. (Mexico); Mora-Ramos, M.E. [Facultad de Ciencias, Universidad Autónoma del Estado de Morelos, Av. Universidad 1001, CP 62209, Cuernavaca, Morelos (Mexico); Instituto de Física, Universidad de Antioquia, AA 1226, Medellín (Colombia); Duque, C.A., E-mail: cduque@fisica.udea.edu.co [Instituto de Física, Universidad de Antioquia, AA 1226, Medellín (Colombia)

    2013-09-01

    In this work we are reporting the energy level spectrum for a quantum system consisting of an n-type double δ-doped quantum well with a Schottky barrier potential in a Gallium Arsenide matrix. The calculated states are taken as the basis for the evaluation of the linear and third-order nonlinear contributions to the optical absorption coefficient and to the relative refractive index change, making particular use of the asymmetry of the potential profile. These optical properties are then reported as a function of the Schottky barrier height (SBH) and the separation distance between the δ-doped quantum wells. Also, the effects of the application of hydrostatic pressure are studied. The results show that the amplitudes of the resonant peaks are of the same order of magnitude of those obtained in the case of single δ-doped field effect transistors; but tailoring the asymmetry of the confining potential profile allows the control the resonant peak positions.

  16. A Comparative Study of Spin Coated Transparent Conducting Thin Films of Gallium and Aluminum Doped ZnO Nanoparticles

    Directory of Open Access Journals (Sweden)

    A. Alkahlout

    2015-01-01

    Full Text Available Transparent conducting Ga:ZnO (GZO and Al:ZnO (AZO layers have been deposited by spin coating on glass substrates using crystalline nanoparticles redispersed in 1-propanol. The coatings have been sintered in air at 600°C for 15 min and then postannealed in a reducing atmosphere at 400°C for 90 min. The effect of Ga and Al doping on the structural, morphological, optical, and electrical properties of the obtained thin films was investigated. Both films were found to be crystalline with a hexagonal structure. A single step spin coated layer 52–56 nm thick is obtained. To increase the thickness and lower the obtained sheet resistance multilayers coatings have been used. The visible transmission of both layers is high (T>80%. The influence of the sintering temperature and the optimum doping concentration was investigated. Five layers synthesized with doping ratio of 1 mol.% and sintered at 600°C and then submitted to reducing treatment in forming gas exhibited a minimum resistivity value of 7.4 × 10−2 Ω·cm for GZO layer and 1.45 Ω·cm for AZO coating.

  17. Influence of addition of indium and of post-annealing on structural, electrical and optical properties of gallium-doped zinc oxide thin films deposited by direct-current magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Pham, Duy Phong [Laboratory of Advanced Materials, University of Science, Vietnam National University, HoChiMinh (Viet Nam); College of Information and Communication Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Nguyen, Huu Truong [Laboratory of Advanced Materials, University of Science, Vietnam National University, HoChiMinh (Viet Nam); Phan, Bach Thang [Laboratory of Advanced Materials, University of Science, Vietnam National University, HoChiMinh (Viet Nam); Faculty of Materials Science, University of Science, Vietnam National University, HoChiMinh (Viet Nam); Hoang, Van Dung [Laboratory of Advanced Materials, University of Science, Vietnam National University, HoChiMinh (Viet Nam); Maenosono, Shinya [School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Tran, Cao Vinh, E-mail: tcvinh@hcmus.edu.vn [Laboratory of Advanced Materials, University of Science, Vietnam National University, HoChiMinh (Viet Nam)

    2015-05-29

    In this study, both gallium-doped zinc oxide (GZO) and indium-added gallium-doped zinc oxide (IGZO) thin films were deposited on commercial glasses by magnetron dc-sputtering in argon atmosphere. The crystal structure, electrical conductivity and optical transmission of as-deposited as well as post-annealed thin films of both GZO and IGZO were investigated for comparison. A small amount of indium introduced into GZO thin films had improved their polycrystalline structure and increased their electrical conductivity by over 29%. All obtained GZO and IGZO thin films have strong [002] crystalline direction, a characteristic orientation of ZnO thin films. Although post-annealed in air at high temperatures up to 500 °C, IGZO thin films still had very low sheet resistance of 6.6 Ω/□. Furthermore, they had very high optical transmission of over 80% in both visible and near-infrared regions. - Highlights: • Doping 0.1 at.% indium enhanced crystalline, electrical properties of GZO films. • The mobility of IGZO films was 25% higher than that of GZO films. • The IGZO films will be potential materials for transparent conducting electrodes.

  18. Spontaneous low frequency oscillation studies in gallium arsenide fast photoconductors

    CERN Document Server

    Foulon, F; Brullot, B; Petit, P; Bergonzo, P; Rubbelynck, C

    1999-01-01

    We have investigated the influence of spontaneous low frequency oscillations (LFO, f approx 0.01 Hz) occurring at high electric field (>1 kV/cm) in resistive photoconductors (PCD) made from semi-insulating GaAs on the response of the PCDs under pulsed gamma-ray irradiation (E approx 1.2 MeV, tau sub F sub W sub H sub M =30 ns). The PCDs were fabricated using GaAs from five commercially available sources. The PCDs were irradiated with fission neutrons in order to reduce their response time down to less than 100 ps. The amplitude of the LFOs was found to be related to the carrier lifetime, and thus defect concentration in the GaAs material. It was larger for material exhibiting high carrier lifetime. Increasing the localised defect concentration, such as EL2 type defect, through GaAs irradiation with fission neutrons was found to decrease the amplitude of the LFOs. PCDs irradiated at high neutron doses (>1x10 sup 1 sup 5 neutrons/cm sup 2) showed no LFOs. It is suggested that interactions between the propagatin...

  19. Gallium arsenide based surface plasmon resonance for glucose monitoring

    Science.gov (United States)

    Patil, Harshada; Sane, Vani; Sriram, G.; Indumathi, T. S; Sharan, Preeta

    2015-07-01

    The recent trends in the semiconductor and microwave industries has enabled the development of scalable microfabrication technology which produces a superior set of performance as against its counterparts. Surface Plasmon Resonance (SPR) based biosensors are a special class of optical sensors that become affected by electromagnetic waves. It is found that bio-molecular recognition element immobilized on the SPR sensor surface layer reveals a characteristic interaction with various sample solutions during the passage of light. The present work revolves around developing painless glucose monitoring systems using fluids containing glucose like saliva, urine, sweat or tears instead of blood samples. Non-invasive glucose monitoring has long been simulated using label free detection mechanisms and the same concept is adapted. In label-free detection, target molecules are not labeled or altered, and are detected in their natural forms. Label-free detection mechanisms involves the measurement of refractive index (RI) change induced by molecular interactions. These interactions relates the sample concentration or surface density, instead of total sample mass. After simulation it has been observed that the result obtained is highly accurate and sensitive. The structure used here is SPR sensor based on channel waveguide. The tools used for simulation are RSOFT FULLWAVE, MEEP and MATLAB etc.

  20. Monolithic series-connected gallium arsenide converter development

    Energy Technology Data Exchange (ETDEWEB)

    Spitzer, M.B.; McClelland, R.W.; Dingle, B.D.; Dingle, J.E.; Hill, D.S. (Kopin Corp., Taunton, MA (United States)); Rose, B.H. (Sandia National Labs., Albuquerque, NM (United States))

    1991-01-01

    We report the development of monolithic GaAs photovoltaic devices intended to convert light generated by a laser or other bright source to electricity. The converters described here can provide higher operating voltage than is possible using a single-junction converter, owing to use of a monolithic circuit that forms a planar series-connected string of single-junction sub-cells. This planar monolithic circuit is arranged to deliver the desired voltage and current during operation at the maximum power point. The paper describes two-, six-, and twelve-junction converters intended for illumination by a laser diode with a wavelength of 0.8 {mu}m. Design and characterization data are presented for optical power in the range of 100 mW to 1 W. The best conversion efficiency exceeds 50%. 9 refs., 4 figs., 2 tabs.

  1. Photoluminescence Study of Ion Implantation Damage in Gallium Arsenide.

    Science.gov (United States)

    1981-12-01

    appreciation is finally extended to my family, whose active moral sup- port was of great comfort during this trying period. Manual V. Key This thesis...Mounted directly behind the sample area on the cylinder was a pre- viously calibrated silicon diode which was used as a tempera - ture sensor. Also on...discriLminator- was connected to an in-house-built interface 26 - -j which amplif ied, stre- tcIed and inv(erted the2 signal properly conditioning it for

  2. High Energy Electron Radiation Degradation of Gallium Arsenide Solar Cells.

    Science.gov (United States)

    1986-03-01

    relative spectral output of the Kratos source was determined. This procedure may be algebraically verified since the cell output current, i, is equal...A (cm2), then a unique voltage may be calculated for given values of 0 and C. Algebraically , this equation may be written as ~q A 77e ____ __ 8) C...position as necessary to achieve proper voltage. (d) Place solar cell on test block using plastic tweezers. (e) Start test program by typing " BASICA

  3. Gallium Arsenide Pilot Line for High Performance Components

    Science.gov (United States)

    1992-05-28

    4K SRAM I, where there are about 100,000 isolated vias. 3.5 Advanced Technology (A. G. Baca, A. I. Faris, R. M. Havrilla , S. E. Lengle, D. D. Manchon...Aluminum Interconnects (R. J. Shul, A. G. Baca, R. M. Havrilla , S. E. Lengle)........... C-3 2.2 Process Tester Characterization (A. G, Baca, D. D. Manchon...TECHNOLOGY 2.1 Aluminum Interconnects (R. J. Shul, A. G. Baca, R. M. Havrilla , S. E. Lengle) The aluminum interconnect metallization process requires

  4. High-performance fused indium gallium arsenide/silicon photodiode

    Science.gov (United States)

    Kang, Yimin

    Modern long haul, high bit rate fiber-optic communication systems demand photodetectors with high sensitivity. Avalanche photodiodes (APDs) exhibit superior sensitivity performance than other types of photodetectors by virtual of its internal gain mechanism. This dissertation work further advances the APD performance by applying a novel materials integration technique. It is the first successful demonstration of wafer fused InGaAs/Si APDs with low dark current and low noise. APDs generally adopt separate absorption and multiplication (SAM) structure, which allows independent optimization of materials properties in two distinct regions. While the absorption material needs to have high absorption coefficient in the target wavelength range to achieve high quantum efficiency, it is desirable for the multiplication material to have large discrepancy between its electron and hole ionization coefficients to reduce noise. According to these criteria, InGaAs and Si are the ideal materials combination. Wafer fusion is the enabling technique that makes this theoretical ideal an experimental possibility. APDs fabricated on the fused InGaAs/Si wafer with mesa structure exhibit low dark current and low noise. Special device fabrication techniques and high quality wafer fusion reduce dark current to nano ampere level at unity gain, comparable to state-of-the-art commercial III/V APDs. The small excess noise is attributed to the large difference in ionization coefficients between electrons and holes in silicon. Detailed layer structure designs are developed specifically for fused InGaAs/Si APDs based on principles similar to those used in traditional InGaAs/InP APDs. An accurate yet straightforward technique for device structural parameters extraction is also proposed. The extracted results from the fabricated APDs agree with device design parameters. This agreement also confirms that the fusion interface has negligible effect on electric field distributions for devices fabricated from high quality fusion materials. The feasibility of fused InGaAs/Si APD for analog systems is also explored. Preliminary two-tone measurement shows that a moderately high dynamic range of 70 dBc/Hz1/2 for broadband Spur Free Dynamic Range (SFDR) or 82 dBc/Hz2/3 suboctave SFDR, up to 50 muA of optical current, can be achieved. The theoretical analyses of SNR show that fused InGaAs/Si APD receivers can provide larger Signal-to-Noise Ratio (SNR) than their III/V counterparts.

  5. Glow Discharge Optical Spectroscopy of Ion Implanted Gallium Arsenide.

    Science.gov (United States)

    1979-12-01

    PECVD processes are silane (SiH4 ) plus either 47 t - Im ammonia (NH 3 ) or nitrogen (N2 ) or both. The chemical reactions are, 3SiH4+2N 2-Si3N 4+6H 2...Physics, 44:5183-5184 (Nov 1973). 68 I i . 13. Sawyer, R., Experimental Spectroscopy, New York: Dover Publication, Inc. (1963) 14. Kerm , W., R. Rosler...composition as functions of the follow- ing parameters: flow, pressure, substrate temperature, and RF power. Kerm , et al., (Ref 14) studied films grown

  6. Mechanism of Current Oscillations in Gallium Arsenide Photoconductive Semiconductor Switches

    Institute of Scientific and Technical Information of China (English)

    TIAN Li-Qiang; SHI Wei

    2008-01-01

    Semi-insulating photoconductive semiconductor switch with an electrode gap of 4mm, triggered by a laser pulse with energy of 0.5mJ, and applied bias of 2.5kV, the periodicity current oscillation with a cycle of 12ns is obtained. It is indicated that the current oscillation is one mode of transferred electron effect, namely quenched domain mode. This mode of trans-electron oscillator is obtained when the instantaneous bias electric field drops below the sustaining field (the minimum electric field required to support the domain) before the domain reaches the anode, which leads to the domain disappears somewhere in the bulk of the switch and away from the ohmic contacts. We mainly analyse the time-dependent characteristic of the mode, the theoretical analysis results are in excellent agreement with the experiment.

  7. Gallium Arsenide Field Effect Transistors with Semi-Insulated Gates.

    Science.gov (United States)

    1977-09-01

    lower carrier concentration . Use of epitaxially grown n+ l ayers was examined as an alternate approach . Dev ices fabricated from this materia l- were...was de- posi ted in preparation for annealing. Initial ly, the S1 3 N4 was deposited by a - - low-temperature, plasma —enhanced process. Unfortunately

  8. Ion-beam induced isolation of gallium arsenide layers

    Science.gov (United States)

    Sengupta, D.; Zemanski, J. M.; Williams, J. S.; Johnson, S. T.; Pogany, A. P.

    1989-07-01

    Epitaxial (n +-n) layers on semi-insulating GaAs samples were implanted with 60 keV He + ions at elevated temperatures. Samples were analysed to provide sheet resistivity, Hall mobility and carrier depth profiles using electrical measurement techniques and damage distributions using TEM and Rutherford backscattering and channeling. All of the data were correlated to identify the optimum conditions to achieve electrical isolation. Elevated temperature He + implants have been found to create uniform, single step isolation of GaAs layers. Isolation of the GaAs layers can be enhanced and stabilised further by a suitable post-implantation annealing process.

  9. Laser Induced Chemical Vapor Epitaxial Growth of Gallium Arsenide Films.

    Science.gov (United States)

    1988-05-23

    heteroepitaxial growth of GaAs. The important process parameters are: the substrate surface cleanliness , substrate temperature, composition and flow rate of the...hydrogen was used as the diluent and win.dw purging gas [9]. The important process parameters are: the substrate surface cleanliness , substrate temperature

  10. Nickel-gallium arsenide high-voltage power Schottky diodes

    Science.gov (United States)

    Ashkinazi, G.; Hadas, Tz.; Meyler, B.; Nathan, M.; Zolotarevski, L.; Zolotarevski, O.

    1993-01-01

    A power GaAs Schottky diode (SD) with a chemically deposited Ni barrier was designed, fabricated and tested. The diode has a reverse breakdown voltage VBR of 140 V, forward voltage drop VF (at 50 A/cm 2) of 0.7 V at 23°C, 0.5 V at 150°C and 0.3 V at 250°C, and reverse leakage current densities jR (at -50 V) of 0.1 μA/cm 2 at 23°C and 1 mA/cm 2 at 150°C. Calculated forward and reverse I- V characteristics using a simple self-consistent computer model are in good agreement with measured values. Calculated characteristics of a silicon SD with identical structure parameters, using the same model, show much poorer VBR, VF and jR values. The theoretical maximum value of VBR is physically limited by the largest allowed VF. For a V Fof ⋍1.6 V, V BR.maxis ⋍200 V in Si and ⋍800 simple technology allows manufacturing of large area GaAs Schottky diodes with average currents up to V in GaAs SDs. Our relatively 100 A.

  11. Photoelastic coupling in gallium arsenide optomechanical disk resonators

    CERN Document Server

    Baker, Christopher; Nguyen, Dac-Trung; Andronico, Alessio; Ducci, Sara; Leo, Giuseppe; Favero, Ivan

    2014-01-01

    We analyze the magnitude of the radiation pressure and electrostrictive stresses exerted by light confined inside GaAs semiconductor WGM optomechanical disk resonators, through analytical and numerical means, and find the electrostrictive force to be of prime importance. We investigate the geometric and photoelastic optomechanical coupling resulting respectively from the deformation of the disk boundary and from the strain-induced refractive index changes in the material, for various mechanical modes of the disks. Photoelastic optomechanical coupling is shown to be a predominant coupling mechanism for certain disk dimensions and mechanical modes, leading to total coupling g$_{om}$ and g$_0$ reaching respectively 3 THz/nm and 4 MHz. Finally, we point towards ways to maximize the photoelastic coupling in GaAs disk resonators, and we provide some upper bounds for its value in various geometries.

  12. Luminescent properties of Cr-doped gallium garnet crystals grown by the micro-pulling-down method

    Science.gov (United States)

    Kurosawa, Shunsuke; Suzuki, Akira; Yamaji, Akihiro; Kamada, Kei; Pejchal, Jan; Ohashi, Yuji; Yokota, Yuui; Chani, Valery Ivanovich; Yoshikawa, Akira

    2016-10-01

    Cr-doped (GdxY1-x)3Ga5O12 crystals (x=0.00, 0.25, 0.50, 0.75 and 1.00) were grown by the micro-pulling-down method and examined for their possible application as red and infrared scintillating detectors in medical field. Although Cr:(Gd0.75Y0.25)3Ga5O12 and Cr:Gd3Ga5O12 had similar X-ray diffraction patterns, other samples showed some change in lattice constant. All the crystals had broad emission bands in the red and infrared region when excited by either 450 nm photons or X rays. These bands were associated with 4T2→A2 transitions. Moreover, redshift of the emission-peak wavelengths (4T2→4A2) and absorption peaks (4A2→4T1 and 4T2) was observed with increase of Gd content (x) in Cr-doped (GdxY1-x)3Ga5O12 due to the change of the crystal fields. The crystals had scintillation emissions in the wavelength region suitable for the real time dose monitoring in radiation therapy.

  13. New Kagome metal Sc₃Mn₃Al₇Si₅ and its gallium-doped analogues: synthesis, crystal structure, and physical properties.

    Science.gov (United States)

    He, Hua; Miiller, Wojciech; Aronson, Meigan C

    2014-09-01

    We report the synthesis, crystal structure, and basic properties of the new intermetallic compound Sc3Mn3Al7Si5. The structure of the compound was established by single-crystal X-ray diffraction, and it crystallizes with a hexagonal structure (Sc3Ni11Si4 type) with Mn atoms forming the Kagome nets. The dc magnetic susceptibility measurements reveal a Curie-Weiss moment of ~0.51 μ(B)/Mn; however, no magnetic order is found for temperatures as low as 1.8 K. Electrical resistivity and heat capacity measurements show that this compound is definitively metallic, with a relatively large specific heat Sommerfeld coefficient, indicating strong electronic correlations. Intriguingly, these features have revealed Sc3Mn3Al7Si5 as a possible quantum spin liquid. With chemical and lattice disorder introduced by doping, a spin liquid to spin glass transition is observed in the highest Ga-doped compounds. The roles of the geometrically frustrated structure and Mn-ligand hybridization in the magnetism of the title compounds are also discussed.

  14. Optical properties of transparent cobalt-containing magnesium aluminosilicate glass-ceramics doped with gallium oxide for saturable absorbers

    Science.gov (United States)

    Loiko, P. A.; Skoptsov, N. A.; Dymshits, O. S.; Malyarevich, A. M.; Yumashev, K. V.; Zhilin, A. A.; Alekseeva, I. P.

    2016-10-01

    Transparent glass-ceramic materials based on glasses of the MgO-Al2O3-SiO2-TiO2 system doped with CoO and Ga2O3 are synthesized. The secondary heat treatment of the initial glasses at temperatures of 800-950°C leads to precipitation of nanosized (6-7 nm) crystals of magnesium aluminogallium spinel doped with cobalt ions and magnesium aluminotitanate solid solutions. The optical absorption spectra of the initial glass and glass-ceramic materials are studied. It is shown that the absorption band caused by the 4 A 2(4F)→ 4 T 1(4 F) transitions of tetrahedrally coordinated Co2+ ions in glass-ceramics with nanosized Co:Mg(Al,Ga)2O4 crystals is shifted to longer wavelengths (up to 1.67 µm) compared to the position of this band in materials with Co:MgAl2O4 crystals. The synthesized glass-ceramics are characterized by a relatively low saturation fluence FS 0.5 ± 0.1 J/cm2 at a wavelength of 1.54 µm, as well as by a high radiation resistance to nanosecond laser pulses, which is no lower than 15 ± 2 J/cm2. This explains their attractiveness as materials for saturable absorbers for erbium lasers emitting in the spectral range 1.5-1.7 µm.

  15. Photoinduced Dissociation Of N-alkyl Bromides On Gallium Arsenide(110) And Gallium Arsenide(100) Electron And Fragment Dynamics

    CERN Document Server

    Khan, K A

    1999-01-01

    In this study we investigate the UV-initiated electron transfer and dissociation fragment dynamics of selected n-alkyl bromides physisorbed on single crystals of GaAs. By systematically varying different chemical and structural parameters of the adsorbate/substrate system we explore a number of fundamental questions regarding the basic physics and chemistry of photochemical processes on surfaces. Monolayers of methyl, ethyl and propyl bromide were deposited on the (110), Ga-terminated (100) and As- terminated (100) surfaces of GaAs without thermal decomposition at 80 K. Substrate-mediated electron transfer to the molecule, induced by exposure to UV light at 193, 248 and 351 nm, causes C-Br bond cleavage. The electron transfer dynamics of this mechanism are examined as a function of wavelength and molecular complexity of the adsorbate to better understand the flow of energy and charge across the adsorbate/substrate interface. The photodynamics of the alkyl fragments are studied using mass-, energy- and angle-r...

  16. Chemical mechanical polishing of Indium phosphide, Gallium arsenide and Indium gallium arsenide films and related environment and safety aspects

    Science.gov (United States)

    Matovu, John Bogere

    As scaling continues with advanced technology nodes in the microelectronic industry to enhance device performance, the performance limits of the conventional substrate materials such as silicon as a channel material in the front-end-of-the-line of the complementary metal oxide semiconductor (CMOS) need to be surmounted. These challenges have invigorated research into new materials such as III-V materials consisting of InP, GaAs, InGaAs for n-channel CMOS and Ge for p-channels CMOS to enhance device performance. These III-V materials have higher electron mobility that is required for the n-channel while Ge has high hole mobility that is required for the p-channel. Integration of these materials in future devices requires chemical mechanical polishing (CMP) to achieve a smooth and planar surface to enable further processing. The CMP process of these materials has been associated with environment, health and safety (EH&S) issues due to the presence of P and As that can lead to the formation of toxic gaseous hydrides. The safe handling of As contaminated consumables and post-CMP slurry waste is essential. In this work, the chemical mechanical polishing of InP, GaAs and InGaAs films and the associated environment, health and safety (EH&S) issues are discussed. InP removal rates (RRs) and phosphine generation during the CMP of blanket InP films in hydrogen peroxide-based silica particle dispersions in the presence and absence of three different multifunctional chelating carboxylic acids, namely oxalic acid, tartaric acid, and citric acid are reported. The presence of these acids in the polishing slurry resulted in good InP removal rates (about 400 nm min-1) and very low phosphine generation (slurry compositions consisting of 3 wt % silica, 1 wt % hydrogen peroxide and 0.08 M oxalic acid or citric acid that provided the best results on blanket InP films were used to evaluate their planarization capability of patterned InP-STI structures of 200 mm diameter wafers. Cross sectional scanning electron microscope (SEM) images showed that InP in the shallow trench isolation structures was planarized and scratches, slurry particles and smearing of InP were absent. Additionally, wafers polished at pH 6 showed very low dishing values of about 12-15 nm, determined by cross sectional SEM. During the polishing of blanket GaAs, GaAs RRs were negligible with deionized water or with silica slurries alone. They were relatively high in aq. solutions of H2O2 alone and showed a strong pH dependence, with significantly higher RRs in the alkaline region. The addition of silica particles to aq. H2O2 did not increase the GaAs RRs significantly. The evolution of arsenic trihydride (AsH3) during the dissolution of GaAs in aq. H2O2 solution was similarly higher in the basic pH range than in neutral pH or in the acidic pH range. However, no AsH3 was measured during polishing, evidently because of the relatively high water solubility of AsH3. The work done on InGaAs polishing shows that InGaAs RR trends are different from those observed for InP or GaAs. InGaAs RRs at pH 2 are higher than those at pH 10 and highest at pH 4. Dissolution rates (DRs), Fourier Transform Infrared Spectroscopy (FTIR), contact angles, X-Ray Photoelectron Spectroscopy (XPS), X-Ray Fluorescence Spectroscopy (XRF), zeta potential measurements and calculated Gibbs free energy changes of the reactions involved during polishing and gas formation were used to discuss the observed RRs and hydride gas generation trends and to propose the reaction pathways involved in the material removal and in hydride gas generation mechanisms.

  17. Theoretical Studies of High Energy Transport of Electrons and Holes in Gallium Arsenide, Indium Phosphide, Indium Arsenide, and Gallium Antimonide.

    Science.gov (United States)

    1984-06-01

    interest and support in many aspects of this work. The author would also like to thank Professors N. Holonyak Jr., G. * Stillman, and B. Wheeler for...York, 1958. [321 R. P. Feynman , Statistical Mechanics, A Set of Lectures, W. A. * -. Benjamin, Reading Ma., 1972. [33] G. 3. lafrate, "Quantum transport

  18. Electroluminescence Studies on Longwavelength Indium Arsenide Quantum Dot Microcavities Grown on Gallium Arsenide

    Science.gov (United States)

    2011-12-01

    K.M. Groom, S. MacNeil, R.A. Hogg, R. Smallwood. “Quantum Dot Superluminescent Diodes for Optical Coherence Tomography: Skin Imaging” IEEE Journal of... diodes (RCLEDs) and three 1.3 µm vertical cavity surface emitting laser (VCSEL) samples were fabricated and electro-optically characterized over a...layer-by-layer, or Frank-van der Merwe growth [18] .................................26 2.17. Active region of diode lasers representing a layer

  19. Lung gallium scan

    Science.gov (United States)

    Gallium 67 lung scan; Lung scan; Gallium scan - lung; Scan - lung ... Gallium is injected into a vein. The scan will be taken 6 to 24 hours after the gallium is injected. (Test time depends on whether your condition is acute or chronic .) ...

  20. Effects of erbium-and chromium-doped yttrium scandium gallium garnet and diode lasers on the surfaces of restorative dental materials: a scanning electron microscope study.

    Science.gov (United States)

    Hatipoglu, M; Barutcigil, C

    2015-01-01

    The aim of this study is to evaluate the potential effects of laser irradiation, which is commonly performed in periodontal surgery, on the surfaces of restorative materials. Five different restorative dental materials were used in this study, as follows: (1) Resin composite, (2) poly acid-modified resin composite (compomer), (3) conventional glass ionomer cement (GIC), (4) resin-modified glass ionomer cement (RMGIC), and (5) amalgam. Four cylindrical samples (8 mm diameter, 2 mm height) were prepared for each restorative material. In addition, four freshly extracted, sound human incisors teeth were selected. Two different laser systems commonly used in periodontal surgery were examined in this study: A 810 nm diode laser at a setting of 1 W with continuous-phase laser irradiation for 10 s, and an erbium-and chromium-doped yttrium scandium gallium garnet (Er, Cr: YSGG) laser at settings of 2.5 W, 3.25 W, and 4 W with 25 Hz laser irradiation for 10 s. Scanning electron microscopy (SEM) analysis was performed to evaluate the morphology and surface deformation of the restorative materials and tooth surfaces. According to the SEM images, the Er, Cr: YSGG laser causes irradiation markings that appear as demineralized surfaces on tooth samples. The Er, Cr: YSGG laser also caused deep defects on composite, compomer, and RMGIC surfaces because of its high power, and the ablation was deeper for these samples. High-magnification SEM images of GIC samples showed the melting and combustion effects of the Er, Cr: YSGG laser, which increased as the laser power was increased. In amalgam samples, neither laser left significant harmful effects at the lowest power setting. The diode laser did cause irradiation markings, but they were insignificant compared with those left by the Er, Cr: YSGG laser on the surfaces of the different materials and teeth. Within the limitations of this study, it can be concluded that Er, Cr: YSGG laser irradiation could cause distortions of the surfaces

  1. Studies of Electronic Conduction in Some Small Gallium Arsenic Based.

    Science.gov (United States)

    Whittington, Geoffrey

    Available from UMI in association with The British Library. Requires signed TDF. This thesis describes experimental investigations of the physics involved with low temperature electronic conduction in three different semiconductor systems. The research relies upon technological advances in fabrication of such semiconductor samples. The first work deals with the effects of quantum interference of electrons in some submicron size, heavily doped Gallium Arsenide wire samples. The interesting effect of aperiodic fluctuations in the magnetoresistance of these samples is studied, making use of recently formulated theory on the subject, and with experimental data taken over the magnetic field range 0 to 10 tesla. The results verify the connection between the mean amplitude of the fluctuations and the field correlation period, in terms of the correlation function introduced in the theory. The second work is on the impurity-assisted tunnelling conduction in a magnetic field of three thin rm n^{+}/n^{-}/n^ {+} GaAs sandwich layer structures. The conduction of the system is shown to be determined by impurities lying in the centre of the middle layer. This allows the connection to be made between the conductivity of the system in a magnetic field, and the field-dependent shape of the donor electron wavefunction. The relative variation in resistance with angle to an applied magnetic field was measured, and is shown to be in agreement with predictions based on calculations of the shape of a normalised hydrogenic state wavefunction in high magnetic fields. The third work concerns the tunnelling conduction of a symmetrical GaAs/(AlGa)As/GaAs hetero-barrier system. The current-voltage characteristics at low temperature are fully modelled for applied voltages up to 180mV, using conventional theory of tunnelling and a position-dependent effective mass in the barrier. Low current oscillations in the Fowler-Nordheim tunnelling regime, corresponding to quantum reflection at the

  2. Gallium-containing hydroxyapatite for potential use in orthopedics

    Energy Technology Data Exchange (ETDEWEB)

    Melnikov, P., E-mail: petrmelnikov@yahoo.com [Department of Clinical Surgery, Faculty of Medicine, Federal University of Mato Grosso do Sul, Campo Grande, Mato Grosso do Sul (Brazil); Teixeira, A.R.; Malzac, A. [Department of Clinical Surgery, Faculty of Medicine, Federal University of Mato Grosso do Sul, Campo Grande, Mato Grosso do Sul (Brazil); Coelho, M. de B. [Brazilian Agricultural Research Corporation - EMBRAPA (Brazil)

    2009-09-15

    A novel material that may be recommended for grafts and implants stimulating bone growth has been obtained by introducing gallium ions (up to 11.0 mass%) into crystalline lattice of hydroxyapatite. The doping was carried out using gallium nitrate and sodium gallate solutions. In both cases, lattice parameters of gallium-doped hydroxyapatite are identical to those of pure synthetic hydroxyapatite. Gallium does not replace calcium as a result of heterovalent substitution and consequently produces no distortions in the framework of hydroxyapatite matrix. It remains strongly fixed in the form of solid solution of intercalation. According to scanning electron microscopy images gallium insertion does not cause any morphological alterations in hydroxyapatite structure and the product developed meets physico-chemical criteria for biomaterial to be employed in orthopedic practice and local handling of traumatic injuries. Its future usage opens the opportunity to enhance osteosynthesis and calcium retention in loco.

  3. Photo-Induced conductivity of heterojunction GaAs/Rare-Earth doped SnO2

    Directory of Open Access Journals (Sweden)

    Cristina de Freitas Bueno

    2013-01-01

    Full Text Available Rare-earth doped (Eu3+ or Ce3+ thin layers of tin dioxide (SnO2 are deposited by the sol-gel-dip-coating technique, along with gallium arsenide (GaAs films, deposited by the resistive evaporation technique. The as-built heterojunction has potential application in optoelectronic devices, because it may combine the emission from the rare-earth-doped transparent oxide, with a high mobility semiconductor. Trivalent rare-earth-doped SnO2 presents very efficient emission in a wide wavelength range, including red (in the case of Eu3+ or blue (Ce3+. The advantage of this structure is the possibility of separation of the rare-earth emission centers, from the electron scattering, leading to an indicated combination for electroluminescence. Electrical characterization of the heterojunction SnO2:Eu/GaAs shows a significant conductivity increase when compared to the conductivity of the individual films. Monochromatic light excitation shows up the role of the most external layer, which may act as a shield (top GaAs, or an ultraviolet light absorber sink (top RE-doped SnO2. The observed improvement on the electrical transport properties is probably related to the formation of short conduction channels in the semiconductors junction with two-dimensional electron gas (2DEG behavior, which are evaluated by excitation with distinct monochromatic light sources, where the samples are deposited by varying the order of layer deposition.

  4. Efeito da terapia com laser de arsenieto de gálio e alumínio (660Nm sobre a recuperação do nervo ciático de ratos após lesão por neurotmese seguida de anastomose epineural: análise funcional Effect of gallium-aluminum-arsenide laser therapy (660Nm on recovery of the sciatic nerve in rats following neurotmesis lesion and epineural anastomosis: functional analysis

    Directory of Open Access Journals (Sweden)

    FA Reis

    2008-06-01

    Full Text Available CONTEXTUALIZAÇÃO: As lesões nervosas periféricas podem comprometer atividades diárias de um indivíduo e resultam em perda da sensibilidade e motricidade do território inervado. OBJETIVO: Com o intuito de acelerar os processos regenerativos, objetivou-se analisar a influência da aplicação do laser de arsenieto de gálio e alumínio (AsGaAl, 660Nm sobre a recuperação funcional do nervo ciático de ratos. MATERIAIS E MÉTODOS: O nervo ciático de 12 ratos Wistar foi submetido à lesão por neurotmese e anastomose epineural e divididos em dois grupos: controle e laserterapia. Após a lesão, utilizou-se o laser de GaAlAs, 660Nm, 4J/cm², 26,3mW, feixe de 0,63cm², em três pontos eqüidistantes sobre a lesão, por 20 dias. As impressões das pegadas dos animais foram obtidas antes e após (sete, 14 e 21 dias pós-operatórios o procedimento cirúrgico e calculou-se o índice funcional do ciático (IFC. RESULTADOS: A comparação do IFC não resultou em diferença significante (p>0,05 entre os grupos. CONCLUSÕES: Conclui-se que os parâmetros e métodos empregados na laserterapia demonstram resultados nulos sobre o IFC no período avaliado.CONTEXT: Peripheral nerve injuries result in sensory and motor losses in the innervated area and can hinder individuals’ daily activities. Objective: The objective was to analyze the influence of applying gallium-aluminum-arsenide (GaAlAs laser (660Nm on the functional recovery of the sciatic nerve in rats. METHODS: The sciatic nerve of 12 Wistar rats was subjected to injury consisting of neurotmesis and epineural anastomosis. The rats were divided into two groups: control and laser therapy. After the injury, a GaAlAs laser was used (660Nm, 4J/cm², 26.3mW and 0.63cm² beam at three equidistant points on the injury, for 20 days. Footprint impressions were obtained from the animals before and seven, 14 and 21 days after the surgical procedure and the sciatic functional index (SFI was calculated

  5. Investigations in gallium removal

    Energy Technology Data Exchange (ETDEWEB)

    Philip, C.V.; Pitt, W.W. [Texas A and M Univ., College Station, TX (United States); Beard, C.A. [Amarillo National Resource Center for Plutonium, TX (United States)

    1997-11-01

    Gallium present in weapons plutonium must be removed before it can be used for the production of mixed-oxide (MOX) nuclear reactor fuel. The main goal of the preliminary studies conducted at Texas A and M University was to assist in the development of a thermal process to remove gallium from a gallium oxide/plutonium oxide matrix. This effort is being conducted in close consultation with the Los Alamos National Laboratory (LANL) personnel involved in the development of this process for the US Department of Energy (DOE). Simple experiments were performed on gallium oxide, and cerium-oxide/gallium-oxide mixtures, heated to temperatures ranging from 700--900 C in a reducing environment, and a method for collecting the gallium vapors under these conditions was demonstrated.

  6. Gallium nitride optoelectronic devices

    Science.gov (United States)

    Chu, T. L.; Chu, S. S.

    1972-01-01

    The growth of bulk gallium nitride crystals was achieved by the ammonolysis of gallium monochloride. Gallium nitride single crystals up to 2.5 x 0.5 cm in size were produced. The crystals are suitable as substrates for the epitaxial growth of gallium nitride. The epitaxial growth of gallium nitride on sapphire substrates with main faces of (0001) and (1T02) orientations was achieved by the ammonolysis of gallium monochloride in a gas flow system. The grown layers had electron concentrations in the range of 1 to 3 x 10 to the 19th power/cu cm and Hall mobilities in the range of 50 to 100 sq cm/v/sec at room temperature.

  7. Spin Injection in Indium Arsenide

    Directory of Open Access Journals (Sweden)

    Mark eJohnson

    2015-08-01

    Full Text Available In a two dimensional electron system (2DES, coherent spin precession of a ballistic spin polarized current, controlled by the Rashba spin orbit interaction, is a remarkable phenomenon that’s been observed only recently. Datta and Das predicted this precession would manifest as an oscillation in the source-drain conductance of the channel in a spin-injected field effect transistor (Spin FET. The indium arsenide single quantum well materials system has proven to be ideal for experimental confirmation. The 2DES carriers have high mobility, low sheet resistance, and high spin orbit interaction. Techniques for electrical injection and detection of spin polarized carriers were developed over the last two decades. Adapting the proposed Spin FET to the Johnson-Silsbee nonlocal geometry was a key to the first experimental demonstration of gate voltage controlled coherent spin precession. More recently, a new technique measured the oscillation as a function of channel length. This article gives an overview of the experimental phenomenology of the spin injection technique. We then review details of the application of the technique to InAs single quantum well (SQW devices. The effective magnetic field associated with Rashba spin-orbit coupling is described, and a heuristic model of coherent spin precession is presented. The two successful empirical demonstrations of the Datta Das conductance oscillation are then described and discussed.

  8. Native gallium adatoms discovered on atomically-smooth gallium nitride surfaces at low temperature.

    Science.gov (United States)

    Alam, Khan; Foley, Andrew; Smith, Arthur R

    2015-03-11

    In advanced compound semiconductor devices, such as in quantum dot and quantum well systems, detailed atomic configurations at the growth surfaces are vital in determining the structural and electronic properties. Therefore, it is important to investigate the surface reconstructions in order to make further technological advancements. Usually, conventional semiconductor surfaces (e.g., arsenides, phosphides, and antimonides) are highly reactive due to the existence of a high density of group V (anion) surface dangling bonds. However, in the case of nitrides, group III rich growth conditions in molecular beam epitaxy are usually preferred leading to group III (Ga)-rich surfaces. Here, we use low-temperature scanning tunneling microscopy to reveal a uniform distribution of native gallium adatoms with a density of 0.3%-0.5% of a monolayer on the clean, as-grown surface of nitrogen polar GaN(0001̅) having the centered 6 × 12 reconstruction. Unseen at room temperature, these Ga adatoms are strongly bound to the surface but move with an extremely low surface diffusion barrier and a high density saturation coverage in thermodynamic equilibrium with Ga droplets. Furthermore, the Ga adatoms reveal an intrinsic surface chirality and an asymmetric site occupation. These observations can have important impacts in the understanding of gallium nitride surfaces.

  9. Magnetic semiconductors for spinelectronics. Europium sulfide and magnetically doped gallium nitride; Magnetische Halbleiter zum Einsatz in der Spinelektronik. Europiumsulfid und magnetisch dotiertes Galliumnitrid

    Energy Technology Data Exchange (ETDEWEB)

    Keller, J.

    2007-07-02

    In this work, magnetic semiconductors were investigated. As ferromagnetic compound semiconductor, EuS was investigated as thin film system. Particular attention was paid to the influence of the substrate temperature during growth on the sample properties. The samples grown and investigated here show an anomalous Hall effect. As diluted magnetic semiconductors (DMS), GaN films magnetically doped with Mn or Gd were investigated. In both material systems, ferromagnetism far above room temperature was demonstrated.While GaGdN shows a homogeneous magnetism, all ferromagnetic GaMnN samples show small clusters (phase separations). In addition, measurements of the optical absorption and the magnetic circular dichroism (MCD) were performed on the GaMnN samples. In the optical measurements, the Mn was identified as deep acceptor. At low temperatures, both the magneto-absorption and the MCD show a Zeeman-shift of an absorption band for all doping levels. The exchange energies between valence band and localized magnetic moments can be extracted from fits of the Brillouin function to the Zeeman shifts. This yields values between 1.4 eV and 1.7 eV for the lowest doping levels and between 1.7 eV and 2.1 eV for the highest doped sample. At low temperatures, no ferromagnetic behavior was found in the magneto-optical experiments. The signal is dominated by the localized Mn spin system. At room temperature, the MCD shows a ferromagnetic signature. At elevated temperatures, the signal from the Mn spin system is small enough that the influence of the clusters on the band structure of the host lattice becomes visible. Contrary to the GaMnN samples, the GaGdN films show a homogeneous magnetism. The magnetically doped GaN thin film systems investigated here exhibit different behavior. The exchange mechanism proposed for GaGdN leads to a homogeneous ferromagnetism and is similar to the magnetic exchange in the Eu chalcogenides. The interplay between this intra-atomic f-d exchange and the

  10. Electrodeposition of gallium for photovoltaics

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, Raghu N.

    2016-08-09

    An electroplating solution and method for producing an electroplating solution containing a gallium salt, an ionic compound and a solvent that results in a gallium thin film that can be deposited on a substrate.

  11. Bragg Reflector-Induced Increased Nonradiative Lifetime in Gallium Arsenide (GaAs)/Aluminum Gallium Arsenide (AlGaAs) Double Heterostructures

    Science.gov (United States)

    2015-09-01

    is essential for the design and analysis of high- efficiency semiconductor solar cells1 and other optoelectronic devices.2 Time-resolved... solar cell uses a GaAs/AlGaAs DH with a roughly 1–2 µm GaAs active region on top of an internal distributed Bragg reflector (BR) to take advantage of...carrier lifetimes and the radiative recombination constant were determined from PL decay time and internal radiative quantum efficiency measurements on

  12. Broadband infrared light-emitting patterns in optical glass by laser-induced nanostructuring of NiO-doped alkali-gallium germanosilicates.

    Science.gov (United States)

    Lotarev, S V; Lipatiev, A S; Golubev, N V; Ignat'eva, E S; Malashkevich, G E; Mudryi, A V; Priseko, Y S; Lorenzi, R; Paleari, A; Sigaev, V N

    2013-02-15

    In this Letter, we show functionalization of NiO-doped 7.5Li(2)O·2.5Na(2)O·20Ga(2)O(3)·35SiO(2)·35GeO(2) glass by space-selective nanocrystallization via exposure to the focused beam of a pulsed copper vapor laser (510.6 and 578.2 nm) at temperature close to the glass transition point (570°C). Irradiated areas drastically change their color, caused by electronic transitions of Ni(2+) dopant ions, without any alteration of the optical quality. Importantly, irradiated regions acquire broadband infrared luminescence (centered at about 1400 nm and possessing 400 nm effective bandwidth) typical of Ni(2+) ions in crystalline environment, and by positive change of refractive index (more than 10(-3)). Spectroscopic and diffractometric data of the irradiated regions indeed resemble those previously observed in thermally nanocrystallized glass, with Ni(2+) ions embedded in γ-Ga(2)O(3) nanocrystals. The results demonstrate the possibility of laser writing nanocrystallized multifunction patterns in germanosilicate glasses for the fabrication of active integrated devices.

  13. A first-principles comparative study of lithium, sodium, and magnesium storage in pure and gallium-doped germanium: Competition between interstitial and substitutional sites

    Science.gov (United States)

    Legrain, Fleur; Manzhos, Sergei

    2017-01-01

    Thermodynamics and kinetics of Li, Na, and Mg storage in Ge are studied ab initio. The most stable configurations can consist of tetrahedral, substitutional, or a combination of the two types of sites. In the dilute limit, Li and Na prefer interstitial, while Mg prefers substitutional sites. At higher concentrations of Li, Na, and Mg, there is a combination of interstitial and substitutional sites. This is an important finding, as most previous ab initio studies of alloying type electrode materials ignored substitutional sites. Insertion energies computed at dilute concentration (x = 1/64) show that Na and Mg insertion are not thermodynamically favored in Ge vs. the formation of bulk Na and Mg, as opposed to Li insertion which is favored. We investigate the effect of p-doping of Ge (with Ga) on the thermodynamics and find that it considerably lowers the defect formation energies associated with the insertion of Li/Na/Mg at tetrahedral sites. On the other hand, the energetics associated with Li/Na/Mg insertion at substitutional sites are not significantly affected. In addition, we compute the migration energy barriers for Li/Na/Mg diffusion between two tetrahedral sites (0.38/0.79/0.66 eV), between two substitutional sites (0.77/0.93/1.83 eV), and between two sites of different types (2.15/1.75/0.85 eV).

  14. High-field phase-diagram of Fe arsenide superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Y.J.; Jaroszynski, J.; Yamamoto, A.; Gurevich, A.; Riggs, S.C.; Boebinger, G.S.; Larbalestier, D. [National High Magnetic Field Laboratory, Florida State University, Tallahassee-FL 32310 (United States); Wen, H.H. [Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Zhigadlo, N.D.; Katrych, S.; Bukowski, Z.; Karpinski, J. [Laboratory for Solid State Physics, ETH Zuerich, CH-8093 Zuerich (Switzerland); Liu, R.H.; Chen, H.; Chen, X.H. [Hefei National Laboratory for Physical Science a Microscale and Department of Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Balicas, L., E-mail: balicas@magnet.fsu.ed [National High Magnetic Field Laboratory, Florida State University, Tallahassee-FL 32310 (United States)

    2009-05-01

    Here, we report an overview of the phase-diagram of single-layered and double-layered Fe arsenide superconductors at high magnetic fields. Our systematic magneto-transport measurements of polycrystalline SmFeAsO{sub 1-x}F{sub x} at different doping levels confirm the upward curvature of the upper critical magnetic field H{sub c2}(T) as a function of temperature T defining the phase boundary between the superconducting and metallic states for crystallites with the ab planes oriented nearly perpendicular to the magnetic field. We further show from measurements on single-crystals that this feature, which was interpreted in terms of the existence of two superconducting gaps, is ubiquitous among both series of single- and double-layered compounds. In all compounds explored by us the zero temperature upper critical field H{sub c2}(0), estimated either through the Ginzburg-Landau or the Werthamer-Helfand-Hohenberg single gap theories, strongly surpasses the weak-coupling Pauli paramagnetic limiting field. This clearly indicates the strong-coupling nature of the superconducting state and the importance of magnetic correlations for these materials. Our measurements indicate that the superconducting anisotropy, as estimated through the ratio of the effective masses gamma = (m{sub c}/m{sub ab}){sup 1/2} for carriers moving along the c-axis and the ab-planes, respectively, is relatively modest as compared to the high-T{sub c} cuprates, but it is temperature, field and even doping dependent. Finally, our preliminary estimations of the irreversibility field H{sub m}(T), separating the vortex-solid from the vortex-liquid phase in the single-layered compounds, indicates that it is well described by the melting of a vortex lattice in a moderately anisotropic uniaxial superconductor.

  15. Material growth and characterization of gallium arsenic antimide on gallium arsenide grown by MOCVD for long wavelength laser applications

    Science.gov (United States)

    Noh, Min-Soo

    Due to the demand for faster and higher bit rate optical communication, long wavelength vertical cavity surface emitting laser (VCSEL) has been attracting great interests because of its ability of 2D array application. Although InGaAsP/InP edge emitting lasers (EEL) have been well developed and commercially available, the lack of high contrast distributed Bragg reflector (DBR) for the material system forced to find new active materials that can be grown on GaAs substrate to exploit AlGaAs/GaAs DBR pairs. For the purpose, GaAsSb has been studied as the active material. This dissertation describes and discusses the GaAsSb semiconductor material growth, the optimization of the growth conditions, and the characterization of the laser devices fabricated from GaAsSb QW structures. Based on the optimal growth conditions, EELs operating at room temperature in CW mode at the wavelength of 1.27 mum have been demonstrated from the GaAsSb QW structure with GaAsP barriers grown monolithically by MOCVD.

  16. Gallium-containing anticancer compounds

    OpenAIRE

    Chitambar, Christopher R.

    2012-01-01

    There is an ever pressing need to develop new drugs for the treatment of cancer. Gallium nitrate, a group IIIa metal salt, inhibits the proliferation of tumor cells in vitro and in vivo and has shown activity against non-Hodgkin’s lymphoma and bladder cancer in clinical trials. Gallium can function as an iron mimetic and perturb iron-dependent proliferation and other iron-related processes in tumor cells. Gallium nitrate lacks cross resistance with conventional chemotherapeutic drugs and is n...

  17. Normal-state charge dynamics in doped BaFe2As2: Roles of doping and necessary ingredients for superconductivity

    Science.gov (United States)

    Nakajima, M.; Ishida, S.; Tanaka, T.; Kihou, K.; Tomioka, Y.; Saito, T.; Lee, C. H.; Fukazawa, H.; Kohori, Y.; Kakeshita, T.; Iyo, A.; Ito, T.; Eisaki, H.; Uchida, S.

    2014-01-01

    In high-transition-temperature superconducting cuprates and iron arsenides, chemical doping plays an important role in inducing superconductivity. Whereas in the cuprate case, the dominant role of doping is to inject charge carriers, the role for the iron arsenides is complex owing to carrier multiplicity and the diversity of doping. Here, we present a comparative study of the in-plane resistivity and the optical spectrum of doped BaFe2As2, which allows for separation of coherent (itinerant) and incoherent (highly dissipative) charge dynamics. The coherence of the system is controlled by doping, and the doping evolution of the charge dynamics exhibits a distinct difference between electron and hole doping. It is found in common with any type of doping that superconductivity with high transition temperature emerges when the normal-state charge dynamics maintains incoherence and when the resistivity associated with the coherent channel exhibits dominant temperature-linear dependence. PMID:25077444

  18. Gallium--A smart metal

    Science.gov (United States)

    Foley, Nora; Jaskula, Brian W.

    2013-01-01

    Gallium is a soft, silvery metallic element with an atomic number of 31 and the chemical symbol Ga. The French chemist Paul-Emile Lecoq de Boisbaudran discovered gallium in sphalerite (a zinc-sulfide mineral) in 1875 using spectroscopy. He named the element "gallia" after his native land of France (formerly Gaul; in Latin, Gallia). The existence of gallium had been predicted in 1871 by Dmitri Mendeleev, the Russian chemist who published the first periodic table of the elements. Mendeleev noted a gap in his table and named the missing element "eka-aluminum" because he determined that its location was one place away from aluminum in the table. Mendeleev thought that the missing element (gallium) would be very much like aluminum in its chemical properties, and he was right. Solid gallium has a low melting temperature (~29 degrees Celsius, or °C) and an unusually high boiling point (~2,204 °C). Because of these properties, the earliest uses of gallium were in high-temperature thermometers and in designing metal alloys that melt easily. The development of a gallium-based direct band-gap semiconductor in the 1960s led to what is now one of the most well-known applications for gallium-based products--the manufacture of smartphones and data-centric networks.

  19. Peculiarities of defect and impurity behaviour in gallium arsenide during surface gettering

    CERN Document Server

    Gorelenok, A T; Kamanin, A V; Kokhanovskii, S I; Mezdrogina, M M; Shmidt, N M; Vasilev, V I

    2002-01-01

    Spatial redistribution of anti-site defects after surface gettering of GaAs wafers coated by an yttrium film has been found. It has been established that both one- and two-side coating of the GaAs wafer with an yttrium film followed by a heat treatment allows a high-resistivity (n = 10 sup 1 sup 2 cm sup - sup 3) material to be obtained with uniform distributions of both electrons and the effective hole lifetime in a depth of 1.6 mm. The material obtained is suitable for creating Schottky barriers and structures for use in both high-power devices and x-ray detectors.

  20. Microwave Semiconductor Research - Materials, Devices and Circuits and Gallium Arsenide Ballistic Electron Transistors.

    Science.gov (United States)

    1985-04-01

    limited effort basis with industrial support. Projected limits, after considerable effort, should reach f 1 00 GHz. TA 77 72 such transistor was the...shorter recovery time each cycle due to the spatial removal of hot electrons. This device is being pursued with a small grant from industry . The...Broadband MMIC FET Amplifiers", Y.S. Wu and H.J. Carlin, Acta Electronica , Vol. 11, No. 6, pp. 39-46 (Nov. 1983). 6. "Double Broadband Matching and

  1. Nuclear magnetization in gallium arsenide quantum dots at zero magnetic field.

    Science.gov (United States)

    Sallen, G; Kunz, S; Amand, T; Bouet, L; Kuroda, T; Mano, T; Paget, D; Krebs, O; Marie, X; Sakoda, K; Urbaszek, B

    2014-01-01

    Optical and electrical control of the nuclear spin system allows enhancing the sensitivity of NMR applications and spin-based information storage and processing. Dynamic nuclear polarization in semiconductors is commonly achieved in the presence of a stabilizing external magnetic field. Here we report efficient optical pumping of nuclear spins at zero magnetic field in strain-free GaAs quantum dots. The strong interaction of a single, optically injected electron spin with the nuclear spins acts as a stabilizing, effective magnetic field (Knight field) on the nuclei. We optically tune the Knight field amplitude and direction. In combination with a small transverse magnetic field, we are able to control the longitudinal and transverse components of the nuclear spin polarization in the absence of lattice strain--that is, in dots with strongly reduced static nuclear quadrupole effects, as reproduced by our model calculations.

  2. Nuclear magnetization in gallium arsenide quantum dots at zero magnetic field

    Science.gov (United States)

    Sallen, G.; Kunz, S.; Amand, T.; Bouet, L.; Kuroda, T.; Mano, T.; Paget, D.; Krebs, O.; Marie, X.; Sakoda, K.; Urbaszek, B.

    2014-02-01

    Optical and electrical control of the nuclear spin system allows enhancing the sensitivity of NMR applications and spin-based information storage and processing. Dynamic nuclear polarization in semiconductors is commonly achieved in the presence of a stabilizing external magnetic field. Here we report efficient optical pumping of nuclear spins at zero magnetic field in strain-free GaAs quantum dots. The strong interaction of a single, optically injected electron spin with the nuclear spins acts as a stabilizing, effective magnetic field (Knight field) on the nuclei. We optically tune the Knight field amplitude and direction. In combination with a small transverse magnetic field, we are able to control the longitudinal and transverse components of the nuclear spin polarization in the absence of lattice strain—that is, in dots with strongly reduced static nuclear quadrupole effects, as reproduced by our model calculations.

  3. Growth and characterization of epitaxial aluminum layers on gallium-arsenide substrates for superconducting quantum bits

    Science.gov (United States)

    Tournet, J.; Gosselink, D.; Miao, G.-X.; Jaikissoon, M.; Langenberg, D.; McConkey, T. G.; Mariantoni, M.; Wasilewski, Z. R.

    2016-06-01

    The quest for a universal quantum computer has renewed interest in the growth of superconducting materials on semiconductor substrates. High-quality superconducting thin films will make it possible to improve the coherence time of superconducting quantum bits (qubits), i.e., to extend the time a qubit can store the amplitude and phase of a quantum state. The electrical losses in superconducting qubits highly depend on the quality of the metal layers the qubits are made from. Here, we report on the epitaxy of single-crystal Al (011) layers on GaAs (001) substrates. Layers with 110 nm thickness were deposited by means of molecular beam epitaxy at low temperature and monitored by in situ reflection high-energy electron diffraction performed simultaneously at four azimuths. The single-crystal nature of the layers was confirmed by ex situ high-resolution x-ray diffraction. Differential interference contrast and atomic force microscopy analysis of the sample’s surface revealed a featureless surface with root mean square roughness of 0.55 nm. A detailed in situ study allowed us to gain insight into the nucleation mechanisms of Al layers on GaAs, highlighting the importance of GaAs surface reconstruction in determining the final Al layer crystallographic orientation and quality. A highly uniform and stable GaAs (001)-(2× 4) reconstruction reproducibly led to a pure Al (011) phase, while an arsenic-rich GaAs (001)-(4× 4) reconstruction yielded polycrystalline films with an Al (111) dominant orientation. The near-atomic smoothness and single-crystal character of Al films on GaAs, in combination with the ability to trench GaAs substrates, could set a new standard for the fabrication of superconducting qubits.

  4. Ultra-Low Power Fiber-Coupled Gallium Arsenide Photonic Crystal Cavity Electro-Optical Modulator

    Science.gov (United States)

    2011-04-11

    200 nA corresponding to voltages of 0, 0.67, and 1 V (inset of Fig. 2(b)). As can be seen, the cavity resonance blueshifts monotonically even for...these ultra- low injection levels. In fact, 50% of the blueshift occurs in the first 20 nA of injection before saturating at approximately 200 nA (Fig...with a better MBE growth method as minimal leakage current was observed for similar devices in [13]. Nonetheless, the total blueshift of 110 pm is

  5. Origin of optical losses in gallium arsenide disk whispering gallery resonators

    CERN Document Server

    Parrain, David; Wang, Guillaume; Guha, Biswarup; Santos, Eduardo Gil; Lemaitre, Aristide; Senellart, Pascale; Leo, Giuseppe; Ducci, Sara; Favero, Ivan

    2015-01-01

    Whispering gallery modes in GaAs disk resonators reach half a million of optical quality factor. These high Qs remain still well below the ultimate design limit set by bending losses. Here we investigate the origin of residual optical dissipation in these devices. A Transmission Electron Microscope analysis is combined with an improved Volume Current Method to precisely quantify optical scattering losses by roughness and waviness of the structures, and gauge their importance relative to intrinsic material and radiation losses. The analysis also provides a qualitative description of the surface reconstruction layer, whose optical absorption is then revealed by comparing spectroscopy experiments in air and in different liquids. Other linear and nonlinear optical loss channels in the disks are evaluated likewise. Routes are given to further improve the performances of these miniature GaAs cavities.

  6. Gallium Arsenide Waveguide Detector Array for Electronic Warfare Support Measure Systems.

    Science.gov (United States)

    1980-08-29

    65 4.2 Procedure .............. ................. 68 4.3 Results ................................ 68 4.3.1 Pulsed...presented here are derived by Marcuse (11] and the notation is chosen to be consistent with his results. Both the TE and TM modes will be considered and the...2 DREI - 3 I+ 2 - 2 V 0. ( 68 ) Equation ( 68 ) is analytically useful only if one can find some closed form for R. The responsivity data of Sun et aZ

  7. Optical and Electrical Characterization of Bulk Grown Indium-Gallium-Arsenide Alloys

    Science.gov (United States)

    2010-03-01

    using the liquid encapsulated Czochralski (LEC) method but suffered from a large number of 13 misfits and some cracks [3]. In 1995, Suzuki et al...properties of samples grown through the vertical Bridgman (or multi-component zone melting growth) method have been investigated through...applications. 2 The InxGa1-xAs samples analyzed here were grown using the vertical Bridgman or multi-component zone melting growth method (MCZM) by

  8. Chromium compensated gallium arsenide detectors for X-ray and γ-ray spectroscopic imaging

    Energy Technology Data Exchange (ETDEWEB)

    Veale, M.C., E-mail: matthew.veale@stfc.ac.uk [Rutherford Appleton Laboratory, Science and Technology Facilities Council, OX11 0QX (United Kingdom); Bell, S.J.; Duarte, D.D. [Rutherford Appleton Laboratory, Science and Technology Facilities Council, OX11 0QX (United Kingdom); Faculty of Engineering and Physical Sciences, University of Surrey, GU2 7XH (United Kingdom); French, M.J.; Schneider, A.; Seller, P.; Wilson, M.D. [Rutherford Appleton Laboratory, Science and Technology Facilities Council, OX11 0QX (United Kingdom); Lozinskaya, A.D.; Novikov, V.A.; Tolbanov, O.P.; Tyazhev, A.; Zarubin, A.N. [Siberian Physical–Technical Institute of Tomsk State University, Tomsk (Russian Federation)

    2014-07-01

    Semi-insulating GaAs material of 500 μm thickness grown using the Liquid Encapsulated Czochralski (LEC) method has been compensated with chromium to produce high resistivity single crystals suitable for spectroscopic imaging applications. Results are presented for the performance of three small pixel detectors each with 80×80 pixels on a 250 μm pitch, fabricated with metal contacts and bonded to a spectroscopic imaging ASIC. Current–voltage measurements demonstrated a material resistivity of 2.5×10{sup 9} Ω cm at room temperature. At an optimised bias voltage, the average energy resolution at 60 keV (FWHM) was in the range 2.8–3.3 keV per pixel. An analysis of the voltage dependent X-ray spectroscopy suggests that the electron mobility lifetime (μτ{sub e}) for each detector is in the range 2.1–4.5×10{sup −5} cm{sup 2} V{sup −1}. The spectroscopic imaging capability of the detectors is also demonstrated in X-ray absorption spectroscopy measurements.

  9. A customizable commercial miniaturized 320×256 indium gallium arsenide shortwave infrared camera

    Science.gov (United States)

    Huang, Shih-Che; O'Grady, Matthew; Groppe, Joseph V.; Ettenberg, Martin H.; Brubaker, Robert M.

    2004-10-01

    The design and performance of a commercial short-wave-infrared (SWIR) InGaAs microcamera engine is presented. The 0.9-to-1.7 micron SWIR imaging system consists of a room-temperature-TEC-stabilized, 320x256 (25 μm pitch) InGaAs focal plane array (FPA) and a high-performance, highly customizable image-processing set of electronics. The detectivity, D*, of the system is greater than 1013 cm-√Hz/W at 1.55 μm, and this sensitivity may be adjusted in real-time over 100 dB. It features snapshot-mode integration with a minimum exposure time of 130 μs. The digital video processor provides real time pixel-to-pixel, 2-point dark-current subtraction and non-uniformity compensation along with defective-pixel substitution. Other features include automatic gain control (AGC), gamma correction, 7 preset configurations, adjustable exposure time, external triggering, and windowing. The windowing feature is highly flexible; the region of interest (ROI) may be placed anywhere on the imager and can be varied at will. Windowing allows for high-speed readout enabling such applications as target acquisition and tracking; for example, a 32x32 ROI window may be read out at over 3500 frames per second (fps). Output video is provided as EIA170-compatible analog, or as 12-bit CameraLink-compatible digital. All the above features are accomplished in a small volume < 28 cm3, weight < 70 g, and with low power consumption < 1.3 W at room temperature using this new microcamera engine. Video processing is based on a field-programmable gate array (FPGA) platform with a soft-embedded processor that allows for ease of integration/addition of customer-specific algorithms, processes, or design requirements. The camera was developed with the high-performance, space-restricted, power-conscious application in mind, such as robotic or UAV deployment.

  10. Theoretical Studies of High Field, High Energy Transport in Gallium Arsenide, Silicon and Heterostructures,

    Science.gov (United States)

    1983-01-01

    semiconductor transport by Kurosawa [15] in 1966. The pioneering work of Fawcett, Boardman and Swain in 1970 [161, which successfully reproduced the...Semiconductors, Montpellier, France, 1981. K. Binder, Monte Carlo Methods in Statistical Physics, Springer- VerlaC, Berlin, 1979. T. Kurosawa , Proc

  11. Formation of defects at high temperature plastic deformation of gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Mikhnovich, V.V.

    2006-03-14

    The purpose of the present thesis consists in acquiring more concrete information concerning the mechanism of the movement of dislocations and types of defects that appear during the process of dislocation motion on the basis of systematic experimental studies of the GaAs deformation. Experimental studies concerning the dependence of the stress of the samples from their deformation at different values of the deformation parameters (like temperature and deformation speed) were conducted in this paper. To determine the concentration of defects introduced in samples during the deformation process the positron annihilation spectroscopy (PAS) method was used. The second chapter of this paper deals with models of movement of dislocations and origination of defects during deformation of the samples. In the third chapter channels and models of positron annihilation in the GaAs samples are investigated. In the forth chapter the used experimental methods, preparation procedure of test samples and technical data of conducted experiments are described. The fifth chapter shows the results of deformation experiments. The sixth chapter shows the results of positron lifetime measurements by the PAS method. In the seventh chapter one can find analyses of the values of defects concentration that were introduced in samples during deformation. (orig.)

  12. Design, Fabrication, and Characterization of 0.1 Micrometer Gallium Arsenide Mesfet's.

    Science.gov (United States)

    Moore, Karen Elizabeth

    Very high performance 0.1 μm GaAs-based MESFET's have been designed, fabricated, and characterized in order to obtain an improved understanding of the full potential of these devices and the effects of process variations and layer structures on device performance. The FET's were fabricated with both "mushroom" and "gamma" gates using a bi-layer (PMMA/P(MMA-MAA)) electron beam lithography process. Process variations, including gate size, shape, and location, and gate recess depth, were systematically evaluated in GaAs FET's through DC and RF transistor performance, biased and un-biased equivalent circuit parameters, and transistor minimum noise figure. The bias dependence of the devices was studied using the results of cold de-embedding to determine intrinsic and extrinsic equivalent circuit values. These bias variations were related back to DC and RF device performance, in order to better understand how to optimize the biasing of a GaAs MESFET. The performance of the devices fabricated and tested was world class, with maximum f_sp {t}{'}s over 100 GHz, f_sp{max}{'}s over 150 GHz, and little sensitivity to process variations. This demonstrates the continued importance of GaAs and GaAs based MESFET's as high performance microwave devices with large scale commercial potential.

  13. Soft-mask fabrication of gallium arsenide nanomembranes for integrated quantum photonics

    CERN Document Server

    Midolo, Leonardo; Kiršanskė, Gabija; Stobbe, Søren

    2015-01-01

    We report on the fabrication of quantum photonic integrated circuits based on suspended GaAs membranes. The fabrication process consists of a single lithographic step followed by inductively-coupled-plasma dry etching through an electron-beam-resist mask and wet etching of a sacrificial layer. This method does not require depositing, etching, and stripping a hard mask, greatly reducing fabrication time and costs, while at the same time yielding devices of excellent structural quality. We discuss in detail the procedures for cleaning the resist residues caused by the plasma etching and present a statistical analysis of the etched feature size after each fabrication step.

  14. The attachment and characterization of DNA probes on gallium arsenide-based semiconductor surfaces

    Science.gov (United States)

    Yang, Joonhyuk

    2007-12-01

    Immobilization of nucleic acid molecules on solid surfaces is the core of numerous important technologies in the genomics, disease diagnostics and biosensors applications. The architecture and density of immobilized probe molecules depend on the type of the solid surface on which they are anchored. Even though many different types of surfaces have been studied as substrates for deoxyribonucleic acid (DNA) attachment, the development of a new type of substrate, which is reproducible, stable, highly controlled and easily transferred to practical applications, is still needed. Recent studies have shown that As terminated GaAs-based semiconductors can be used as substrates for immobilized DNA layers. In this study, I aim to understand the attachment of nucleic acid onto the surfaces of As-terminated GaAs-based semiconductors and focus on improving the "brush-structure", which is essential for high quality of biochip based on a DNA layer. Attachment of 8-base and 100-base thiolated ssDNA layers on arsenic terminated GaAs(001) was achieved and characterized. The covalent bonds between the thiolated oligonucleotides with As atoms on the GaAs surface were investigated using x-ray photoelectron spectroscopy (XPS), and the surface morphology was obtained using atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). In addition, I studied the effect of DNA length and the presence of a good solvent, such as water, on the oligonucleotides on a GaAs surface. I also investigated the effects of the thiol-based spacer and electrolyte concentration to improve the brush-like structure of the DNA layer. Finally, irradiation effects and AlGaAs resonators have been studied for the applications of DNA brush layer on GaAs as biosensor during the change of attachment probe DNA and hybridization to target DNA. For the 8-base thiolated ssDNA case, AFM results showed that the layer thickness was about ˜2.2 nm in dry mode and increased in wet mode. Replacement reaction from N-, O-As bonds to S-As bonds was observed with addition of MCH as indicated by analysis of XPS spectra. The concentration of electrolyte affected the brush like layer structure. In the case of the longer, more flexible DNA with 100 bases, the DNA molecules strongly interacted with each other and formed big cluster, of 330˜440nm in diameter on the surface. Finally, for the applications, a high level of radiation destroyed the brush layer. An AlGaAs resonator used as proof of concept a change in mass by a change in resonance frequency under hybridization reaction with complementary target DNA. This result shows that the design is viable and has a defection of ˜25pg.

  15. Computer modeling characterization, and applications of Gallium Arsenide Gunn diodes in radiation environments

    Energy Technology Data Exchange (ETDEWEB)

    El- Basit, Wafaa Abd; El-Ghanam, Safaa Mohamed; Kamh, Sanaa Abd El-Tawab [Electronics Research Laboratory, Physics Department, Faculty of Women for Arts, Science and Education, Ain-Shams University, Cairo (Egypt); Abdel-Maksood, Ashraf Mosleh; Soliman, Fouad Abd El-Moniem Saad [Nuclear Materials Authority, Cairo (Egypt)

    2016-10-15

    The present paper reports on a trial to shed further light on the characterization, applications, and operation of radar speed guns or Gunn diodes on different radiation environments of neutron or γ fields. To this end, theoretical and experimental investigations of microwave oscillating system for outer-space applications were carried out. Radiation effects on the transient parameters and electrical properties of the proposed devices have been studied in detail with the application of computer programming. Also, the oscillation parameters, power characteristics, and bias current were plotted under the influence of different γ and neutron irradiation levels. Finally, shelf or oven annealing processes were shown to be satisfactory techniques to recover the initial characteristics of the irradiated devices.

  16. Surface preparation for ALD of High-k dielectrics on indium gallium arsenide

    Science.gov (United States)

    Melitz, Wilhelm

    The key for a successful gate-first process is when subsequent processing steps cannot degrade the semiconductor, the dielectric, or the oxide-semiconductor interfaces. For silicon, the only commercial ALD high-k fabrication process, which avoids processing induced damage, is a replacement gate process (a type of gate-last process). While preparing silicon for gate-last processing is straightforward, the key to a gate-last process for III-V semiconductors is the order and cleanliness of the III-V channel prior to dielectric deposition. Aggressive oxide thickness reduction (equivalent oxide thickness, or EOT, scaling) is needed to fabricate small gate length devices with small subthreshold swings. Furthermore, aggressive EOT scaling requires a very high uniform ALD nucleation density, with no pinholes due to surface contaminants. The key barrier to solving a very practical problem is a surface chemistry challenge: develop a chemical process which removes nearly all air induced defects and contaminants and leaves the III-V surface flat and electrically active for high nucleation density ALD gate oxide deposition, which unpins the Fermi level. The following study uses scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) to observe the removal of the oxide layer and restoration of the clean InGaAs surface reconstruction with atomic hydrogen cleaning, allowing for a gate-last or replacement-gate process. Along with surface cleaning STM and STS was used to characterize the initial passivation of InGaAs surfaces via ALD of trimethyl aluminum (TMA). The substrate temperature and initial surface reconstruction was critical to forming an unpinned passivation layer with a high nucleation density. A method was developed to use Kelvin probe force microscopy (KPFM) as a tool for insightful feedback on the electrostatics of scaled MOSFET devices. KPFM is a unique technique for providing two-dimensional potential profiles inside a working device. A procedure is described to obtain high-resolution KPFM results on ultra-high vacuum (UHV) cleaved III-V MOSCAPs.

  17. A simple soft lithographic nanopatterning of gold on gallium arsenide via galvanic displacement.

    Science.gov (United States)

    Lim, Hyuneui; Noh, Jung-Hyun; Choi, Dae-Geun; Kim, Wan-Doo; Maboudian, Roya

    2010-08-01

    Nanoscale patterning of gold layers on GaAs substrate is demonstrated using a combination of soft lithographic molding and galvanic displacement deposition. First, an electroless deposition method has been developed to plate gold on GaAs with ease and cost-effectiveness. The electroless metallization process is performed by dipping the GaAs substrates into a gold salt solution without any reducing agents or additives. The deposition proceeds via galvanic displacement in which gold ions in the aqueous solution are reduced by electrons arising from the GaAs substrate itself. The deposition rate, surface morphology and adhesion property can be modulated by the plating parameters such as the choice of acids and the immersion time. Second, soft lithographic patterning of nanodots, nanorings, and nanolines are demonstrated on GaAs substrates with hard-polydimethylsiloxane (h-PDMS) mold and plasma etching. This method can be easily applied to the metallization and nanopatterning of gold on GaAs surfaces.

  18. Digital Control of the Czochralski Growth of Gallium Arsenide-Controller Software Reference Manual

    Science.gov (United States)

    1987-07-15

    response by means of two stacked PID controllers . The setpoint and actual data inputs of both controllers are to be connected in parallel; the output of...setpoints is obtained from two stacked PID controllers which permit to obtain a non- linear control response (compare chapter 4.5.1). The first PID...the "manu- al" setpoint can be chosen to lie close to the actually re- quired controller output, the PID controllers need only make small

  19. Preparation of quantum fingerprint(TM)-ready metal-gallium arsenide interfaces for molecular characterization

    Science.gov (United States)

    De Castro, Julian Paulo B.

    Breast cancer is one of the most common cancers in women with a very high incident rate, especially for those women who are between 40-60 years old. Most drugs are large or non-polar macromolecules, which cannot get into cancer cells autonomously, so a method that can deliver those drugs is very important. Optoporation method has been facilitated with gold nanoparticles, which are bound to breast cancer cells, and then absorb the optical energy to improve the membrane permeabilization. Long-term dietary consumption of fruits and vegetables high in beta-carotene and other phytochemicals has been shown beneficial in terms of anti-cancer, anti-aging, preventing cardiovascular disease and cataract. However they are large non-polar molecules that are difficult to enter the cancer cells. Here in this study, we applied optoporation method by using beta-carotene, and tetracycline as anti-cancer drugs in various concentrations to optimize highest selective cell death/best potential for T47D breast cancer cell lines.

  20. A Gallium Arsenide MESFET Operational Amplifier for Use in Composite Operational Amplifiers

    Science.gov (United States)

    1993-12-01

    F., Operational Amplifiers and Linear Integrated Circuits, 4th ed., Prentice Hall, 1991. 6. Sedra , A. S., and Smith , K. C., Microelectronic Circuits...7, pp. 1422-1429, July 1992. 17. McCamant, A. J., McCormack G. D., and Smith , D. H., "An Improved GaAs MESFET Model for SPICE," IEEE Transactions of...34Modeling Frequency Dependence of out Impedance of a Microwave MESFET at Low Frequencies," Electronics Letters, pp. 528-529, June 1985. 39. Smith , M. et al

  1. Two-valley Hydrodynamical Models for Electron Transport in Gallium Arsenide: Simulation of Gunn Oscillations

    Directory of Open Access Journals (Sweden)

    A. Marcello Anile

    2002-01-01

    Full Text Available To accurately describe non-stationary carrier transport in GaAs devices, it is necessary to use Monte Carlo methods or hydrodynamical (or energy transport models which incorporate population transfer between valleys.We present here simulations of Gunn oscillations in a GaAs diode based on two-valley hydrodynamical models: the classic Bløtekjær model and two recently developed moment expansion models. Scattering parameters within the models are obtained from homogeneous Monte Carlo simulations, and these are compared against expressions in the literature. Comparisons are made between our hydrodynamical results, existing work, and direct Monte Carlo simulations of the oscillator device.

  2. Gallium arsenide p+–n–p+-structures with impoverished base area

    Directory of Open Access Journals (Sweden)

    Karimov A. V.

    2009-06-01

    Full Text Available It is displayed experimentally, that the current transport’s mechanism through p+GaAs–nGaAs–p+GaAs-structure is formed by injection-tunnel and generation-recombination mechanisms. Injection-tunnel current prevails at modulation of base’s part which contains defects, and generation-recombination currents are determinative at modulation of base’s part with lesser defectiveness. p+GaAs–nGaAs–p+GaAs-structures are of interest for creating voltage suppressors and electronic switches on their base.

  3. Computer Modeling, Characterization, and Applications of Gallium Arsenide Gunn Diodes in Radiation Environments

    Directory of Open Access Journals (Sweden)

    Wafaa Abd El-Basit

    2016-10-01

    Full Text Available The present paper reports on a trial to shed further light on the characterization, applications, and operation of radar speed guns or Gunn diodes on different radiation environments of neutron or γ fields. To this end, theoretical and experimental investigations of microwave oscillating system for outer-space applications were carried out. Radiation effects on the transient parameters and electrical properties of the proposed devices have been studied in detail with the application of computer programming. Also, the oscillation parameters, power characteristics, and bias current were plotted under the influence of different γ and neutron irradiation levels. Finally, shelf or oven annealing processes were shown to be satisfactory techniques to recover the initial characteristics of the irradiated devices.

  4. Hot-Electron Degradation of Gallium Arsenide Metal-Semiconductor Field-Effect Transistors.

    Science.gov (United States)

    Tkachenko, Yevgeniy A.

    1995-01-01

    The physical mechanism of gradual degradation of GaAs MESFETs during RF overdrive is investigated in detail. A hot-electron effect was found responsible for this so-called "power slump" problem. Hot electrons produced by a large drain-gate voltage swing, tunnel from the MESFET channel and get trapped in SiN. These trapped electrons (i) increase surface depletion, hence reduce maximum channel current, transconductance and transistor gain, (ii) increase knee voltage through an increase in series channel resistance, (iii) relax gate-drain field distribution, thereby suppressing avalanche breakdown, (iv) decrease gate-drain capacitance, hence rm S_{22} under open-channel condition, and (v) increase surface leakage through trap hopping in SiN. The damage to SiN can only be partially recovered by deep UV illumination or 200^circrm C anneal. The evidence supports that trapping occurs in the bulk SiN, instead of at the GaAs/SiN interface. The possible chemical reaction responsible for this trap formation is breaking of the Si-H bond in SiN. An analytical theory of hot-electron effects, which combines hot-electron trapping with gate-drain breakdown and pinched-channel electro-luminescence, was developed and verified using experimental data and numerical simulations. Based on this theory, the rate of hot electron trapping was obtained and the threshold energy for trap formation was determined. The square-root time dependence given by the theory and the threshold energy of 1.9 eV were found consistent with gate current and electro-luminescence measurements. Numerical analysis was consistent with a trap density of the order of 5times10^{12}/rm cm^2 over a distance of approximately 0.1 murm m from the gate toward the drain, and it predicted the experimentally observed open-channel current reduction and gate-drain field relaxation. The spatial distribution of trapped electrons was directly observed by a novel high-voltage electron-beam-induced -current imaging technique. It confirmed the model's prediction. These results can be incorporated into large-signal transistor models for computer-aided circuit design. Such models would quantify trade-off between performance and reliability. An accelerated qualification procedure for the hot-electron-induced degradation trend is devised. This is based on the high-frequency waveform probing and high -sensitivity electro-luminescence measurements. Hot-electron-induced degradation was also found to take place in pseudomorphic high-electron-mobility transistors (PHEMT). The basic signatures of PHEMT degradation are similar to those of MESFETs, however some differences exist due to the structural differences between them. For PHEMT, in addition to SiN surface passivation, hot-electron traps may be formed in the AlGaAs layer under the gate. In addition, various temperature-activated degradation modes are more strongly coupled in the case of PHEMT, which requires analyzing them separately from the field-activated mode.

  5. Type-II indium arsenide/gallium antimonide superlattices for infrared detectors

    Science.gov (United States)

    Mohseni, Hooman

    In this work, the unique properties of type-II InAs/GaSb heterojunctions were utilized for the realization of novel infrared photodetectors with higher operating temperature, detectivity and uniformity than the commonly available infrared detectors. This effort was concentrated on two major devices: uncooled infrared detectors in the long wavelength infrared (LWIR) range, and cooled devices in the very long wavelength infrared (VLWIR) range. Uncooled infrared (IR) detectors are required for low-cost, lightweight sensor systems that have many industrial and medical applications. Commercially available uncooled IR sensors use ferroelectric or microbolometer detectors. These sensors are inherently slow and cannot detect rapid signal changes needed for high-speed infrared systems. Some of the applications which require a fast detector (tau LIDARs. Although photon detectors have frequency responses in the megahertz range, their high temperature detectivity is severely degraded due to high Auger recombination rates. Bandgap engineering was used in order to suppress Auger recombination at room temperature in type-II superlattices. Our experimental results demonstrated nearly one order of magnitude lower Auger recombination rate at room temperature in these type-II superlattices compared to typical intrinsic detectors, such as HgCdTe, with similar bandgap. Uncooled detectors based on the engineered superlattices showed a detectivity of 1.3 x 108g cmHz 1/2/W at 11 Et m, which is comparable to microbolometers. However, the measured response time of the detectors was more than five orders of magnitude faster than microbolometers. In parallel, devices for operation in the VLWIR were developed. High-performance infrared detectors with cutoff wavelength above 14 mum are highly needed for many space-based applications. Commonly used detectors are extrinsic silicon and HgCdTe. However, the former has to be cooled below 10K, and the latter do not have good uniformity in the VLWIR range. We demonstrated high-performance type-II superlattice photodiodes with cutoff wavelength up to 25 mum and excellent bandgap uniformity over a three-inch wafer area. Devices with a 50% cutoff wavelength of 16 mum showed a nearly 50% internal quantum efficiency and background limited infrared photodetector (BLIP) performance at T = 60 K for the first time.

  6. Ultrafast Relaxation Dynamics of Photo-excited Dirac Fermion in Three Dimensional Dirac Semimetal Cadmium Arsenide

    CERN Document Server

    Lu, Wei; Liu, Xuefeng; Lu, Hong; Li, Caizhen; Lai, Jiawei; Zhao, Chuan; Tian, Ye; Liao, Zhimin; Jia, Shuang; Sun, Dong

    2016-01-01

    Three dimensional (3D) Dirac semimetal exhibiting ultrahigh mobility has recently attracted enormous research interests as 3D analogues of graphene. From the prospects of future application toward electronic/optoelectronic devices with extreme performance, it is crucial to understand the relaxation dynamics of photo-excited carriers and their coupling with lattice. In this work, we report ultrafast transient reflection measurements of photo-excited carrier dynamics in cadmium arsenide (Cd3As2), which is among the most stable Dirac semimetals that have been confirmed experimentally. With low energy probe photon of 0.3 eV, photo-excited Dirac Fermions dynamics closing to Dirac point are probed. Through transient reflection measurements on bulk and nanoplate samples that have different doping intensities, and systematic probe wavelength, pump power and lattice temperature dependent measurements, the dynamical evolution of carrier distributions can be retrieved qualitatively using a two-temperature model. The pho...

  7. Gallium Safety in the Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Lee C. Cadwallader

    2003-06-01

    A university laboratory experiment for the US Department of Energy magnetic fusion research program required a simulant for liquid lithium. The simulant choices were narrowed to liquid gallium and galinstan (Ga-In-Sn) alloy. Safety information on liquid gallium and galinstan were compiled, and the choice was made to use galinstan. A laboratory safety walkthrough was performed in the fall of 2002 to support the galinstan experiment. The experiment has been operating successfully since early 2002.

  8. Gallium Safety in the Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Cadwallader, L.C.

    2003-05-07

    A university laboratory experiment for the US Department of Energy magnetic fusion research program required a simulant for liquid lithium. The simulant choices were narrowed to liquid gallium and galinstan (Ga-In-Sn) alloy. Safety information on liquid gallium and galinstan were compiled, and the choice was made to use galinstan. A laboratory safety walkthrough was performed in the fall of 2002 to support the galinstan experiment. The experiment has been operating successfully since early 2002.

  9. Gallium-67 myocardial scintigraphy in dilated cardiomyopathy

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Toshikazu; Konishi, Tokuji; Koyama, Takao; Morita, Yuriko; Futagami, Yasuo; Hayashi, Takamaro; Hamada, Masayuki; Nakano, Takeshi

    1988-12-01

    Gallium-67 imaging has been employed clinically in the detection of malignant tumor or chronic inflammatory disease. In this study, we evaluated the usefulness of Gallium-67 myocardial imaging as an adjunct to endomyocardial biopsy in the diagnosis of myocarditis. Nine patients who had been diagnosed clinically as dilated cardiomyopathy underwent Gallium-67 myocardial imaging. Left ventricular endomyocardial biopsy was performed on all patients. Two had positive Gallium-67 imaging, but myocarditis was not proven in their tissue specimen. Two others with proven myocarditis had negative Gallium-67 imaging. These results suggest that Gallium-67 imaging is not always a useful tool to detect latent myocarditis in patients with dilated cardiomyopathy.

  10. Framework structures of interconnected layers in calcium iron arsenides.

    Science.gov (United States)

    Stürzer, Tobias; Hieke, Christine; Löhnert, Catrin; Nitsche, Fabian; Stahl, Juliane; Maak, Christian; Pobel, Roman; Johrendt, Dirk

    2014-06-16

    The new calcium iron arsenide compounds Ca(n(n+1)/2)(Fe(1-x)M(x))(2+3n)M'(n(n-1)/2)As((n+1)(n+2)/2) (n = 1-3; M = Nb, Pd, Pt; M' = □, Pd, Pt) were synthesized and their crystal structures determined by single-crystal X-ray diffraction. The series demonstrates the structural flexibility of iron arsenide materials, which otherwise prefer layered structures, as is known from the family of iron-based superconductors. In the new compounds, iron arsenide tetrahedral layers are bridged by iron-centered pyramids, giving rise to so far unknown frameworks of interconnected FeAs layers. Channels within the structures are occupied with calcium and palladium or platinum, respectively. Common basic building blocks are identified that lead to a better understanding of the building principles of these structures and their relation to CaFe4As3.

  11. Effect of gallium incorporation on the physical properties of ZnO films grown by spray pyrolysis

    Science.gov (United States)

    Ramakrishna Reddy, K. T.; Gopalaswamy, H.; Reddy, P. J.; Miles, R. W.

    2000-03-01

    Gallium-doped zinc oxide thin films were deposited by the spray pyrolysis technique onto Corning 7059 glass substrates at a temperature of 350°C using a precursor solution of zinc acetate in isopropyl alcohol. The films were prepared using different gallium concentrations keeping the other deposition parameters such as air and solution flow rates and solution concentration constant. The variations of the structural, electrical and optical properties with the doping concentration were investigated. X-ray diffraction data showed that the films were polycrystalline with the (0 0 2) preferred orientation. The texture coefficient and grain size were evaluated for different doping concentrations. The films with 5.0 at% gallium had a resistivity of 1.5×10 -3 Ω cm and a transmittance of 85% with an energy band gap of 3.35 eV.

  12. Gallium localization in peritonitis. Two case reports

    Energy Technology Data Exchange (ETDEWEB)

    LaManna, M.M.; Saluk, P.H.; Zekavat, P.P.; Mobini, J.; Parker, J.A.

    1984-01-01

    Diffuse abdominal localization of gallium was found in two patients with peritonitis, one due to M. tuberculosis and the other presumably pyogenic. Gallium scanning may be useful in the diagnosis of peritonitis and perhaps of other serosal infections.

  13. Pbsub(1-x)Snsub(x)Te (x=0,00 and 0,20) alloying with gallium and cadmium

    Energy Technology Data Exchange (ETDEWEB)

    Novoselova, A.V.; Zlomanov, V.P.; Gas' kov, A.M.; Ryabova, L.I.; Lazarenko, M.A.; Lisina, N.G.

    Investigation results of doping conditions of PbTe and Pbsub(O.8)Snsub(0.2)Te crystals with gallium and cadmium both in the process of growing and diffusional annealing in component vapours are presented. The concentration of the introduced addition in alloyed samples is determined by chemical analysis; homogeneity of its distribution in crystal volume is studied using the Auger-electron microanalysis. Kinetics of gallium solid solution decomposition in lead telluride is investigated. Galvanomagentic and photoelectric properties of the doped crystals are studied in the temperature range of 4-300 K.

  14. Gallium phosphide energy converters

    Energy Technology Data Exchange (ETDEWEB)

    Sims, P.E.; Dinetta, L.C.; Goetz, M.A.

    1995-10-01

    Gallium phosphide (GaP) energy converters may be successfully deployed to provide new mission capabilities for spacecraft. Betavoltaic power supplies based on the conversion of tritium beta decay to electricity using GaP energy converters can supply long term low-level power with high reliability. High temperature solar cells, also based on GaP, can be used in inward-bound missions greatly reducing the need for thermal dissipation. Results are presented for GaP direct conversion devices powered by Ni-63 and compared to the conversion of light emitted by tritiarated phosphors. Leakage currents as low as 1.2 x 10(exp {minus}17) A/sq cm have been measured and the temperature dependence of the reverse saturation current is found to have ideal behavior. Temperature dependent IV, QE, R(sub sh), and V(sub oc) results are also presented. These data are used to predict the high-temperature solar cell and betacell performance of GaP devices and suggest appropriate applications for the deployment of this technology.

  15. The 3-5 semiconductor solid solution single crystal growth. [low gravity float zone growth experiments using gallium indium antimonides and cadmium tellurides

    Science.gov (United States)

    Gertner, E. R.

    1980-01-01

    Techniques used for liquid and vapor phase epitaxy of gallium indium arsenide are described and the difficulties encountered are examined. Results show that the growth of bulk III-V solid solution single crystals in a low gravity environment will not have a major technological impact. The float zone technique in a low gravity environment is demonstrated using cadmium telluride. It is shown that this approach can result in the synthesis of a class of semiconductors that can not be grown in normal gravity because of growth problems rooted in the nature of their phase diagrams.

  16. Oligonuclear gallium nitrogen cage compounds: molecular intermediates on the way from gallium hydrazides to gallium nitride.

    Science.gov (United States)

    Uhl, Werner; Abel, Thomas; Hagemeier, Elke; Hepp, Alexander; Layh, Marcus; Rezaeirad, Babak; Luftmann, Heinrich

    2011-01-03

    Gallium hydrazides are potentially applicable as facile starting compounds for the generation of GaN by thermolysis. The decomposition pathways are, however, complicated and depend strongly on the substituents attached to the gallium atoms and the hydrazido groups. This paper describes some systematic investigations into the thermolysis of the gallium hydrazine adduct Bu(t)(3)Ga←NH(2)-NHMe (1a) and the dimeric gallium hydrazides [R(2)Ga(N(2)H(2)R')](2) (2b, R = Bu(t), R' = Bu(t); 2c, R = Pr(i), R' = Ph; 2d, R = Me, R' = Bu(t)) which have four- or five-membered heterocycles in their molecular cores. Heating of the adduct 1a to 170 °C gave the heterocyclic compound Bu(t)(2)Ga(μ-NH(2))[μ-N(Me)-N(=CH(2))]GaBu(t)(2) (3) by cleavage of N-N bonds and rearrangement. 3 was further converted at 400 °C into the tetrameric gallium cyanide (Bu(t)(2)GaCN)(4) (4). The thermolysis of the hydrazide (Bu(t)(2)Ga)(2)(NH-NHBu(t))(2) (2b) at temperatures between 270 and 420 °C resulted in cleavage of all N-N bonds and the formation of an octanuclear gallium imide, (Bu(t)GaNH)(8) (6). The trimeric dialkylgallium amide (Bu(t)(2)GaNH(2))(3) (5) was isolated as an intermediate. Thermolysis of the hydrazides (Pr(i)(2)Ga)(2)(NH-NHPh)(NH(2)-NPh) (2c) and (Me(2)Ga)(2)(NH-NHBu(t))(2) (2d) proceeded in contrast with retention of the N-N bonds and afforded a variety of novel gallium hydrazido cage compounds with four gallium atoms and up to four hydrazido groups in a single molecule: (Pr(i)Ga)(4)(NH-NPh)(3)NH (7), (MeGa)(4)(NH-NBu(t))(4) (8), (MeGa)(4)(NH-NBu(t))(3)NBu(t) (9), and (MeGa)(4)(NHNBu(t))(3)NH (10). Partial hydrolysis gave reproducibly the unique octanuclear mixed hydrazido oxo compound (MeGa)(8)(NHNBu(t))(4)O(4) (11).

  17. Ultrabroadband terahertz characterization of highly doped ZnO and ITO

    DEFF Research Database (Denmark)

    Wang, Tianwu; Zalkovskij, Maksim; Iwaszczuk, Krzysztof

    2015-01-01

    The broadband complex conductivities of transparent conducting oxides (TCO), namely, aluminum-doped zinc oxide (AZO), gallium-doped zinc oxide (GZO) and tin-doped indium oxide (ITO), were investigated by using THz-TDS from 0.5 to 18 THz. The complex conductivities were accurately calculated using...... resonance tail even in the low frequency part of the spectrum....

  18. Common features of gallium perovskites

    NARCIS (Netherlands)

    Aleksiyko, R; Berkowski, M; Byszewski, P; Dabrowski, B; Diduszko, R; Fink-Finowicki, J; Vasylechko, LO

    2001-01-01

    The Czochralski and floating zone methods have been used to grow single crystals of gallium perovskites solid solutions with rare earth elements La, Pr, Nd, Sm and with Sr. The structure of the crystals has been investigated by powder X-ray, synchrotron radiation and neutron diffraction methods over

  19. Gallium nitride electronics

    Science.gov (United States)

    Rajan, Siddharth; Jena, Debdeep

    2013-07-01

    In the past two decades, there has been increasing research and industrial activity in the area of gallium nitride (GaN) electronics, stimulated first by the successful demonstration of GaN LEDs. While the promise of wide band gap semiconductors for power electronics was recognized many years before this by one of the contributors to this issue (J Baliga), the success in the area of LEDs acted as a catalyst. It set the field of GaN electronics in motion, and today the technology is improving the performance of several applications including RF cell phone base stations and military radar. GaN could also play a very important role in reducing worldwide energy consumption by enabling high efficiency compact power converters operating at high voltages and lower frequencies. While GaN electronics is a rapidly evolving area with active research worldwide, this special issue provides an opportunity to capture some of the great advances that have been made in the last 15 years. The issue begins with a section on epitaxy and processing, followed by an overview of high-frequency HEMTs, which have been the most commercially successful application of III-nitride electronics to date. This is followed by review and research articles on power-switching transistors, which are currently of great interest to the III-nitride community. A section of this issue is devoted to the reliability of III-nitride devices, an area that is of increasing significance as the research focus has moved from not just high performance but also production-worthiness and long-term usage of these devices. Finally, a group of papers on new and relatively less studied ideas for III-nitride electronics, such as interband tunneling, heterojunction bipolar transistors, and high-temperature electronics is included. These areas point to new areas of research and technological innovation going beyond the state of the art into the future. We hope that the breadth and quality of articles in this issue will make it

  20. Evaluation of critical materials for five advanced design photovoltaic cells with an assessment of indium and gallium

    Energy Technology Data Exchange (ETDEWEB)

    Watts, R.L.; Gurwell, W.E.; Jamieson, W.M.; Long, L.W.; Pawlewicz, W.T.; Smith, S.A.; Teeter, R.R.

    1980-05-01

    The objective of this study is to identify potential material supply constraints due to the large-scale deployment of five advanced photovoltaic (PV) cell designs, and to suggest strategies to reduce the impacts of these production capacity limitations and potential future material shortages. This report presents the results of the screening of the five following advanced PV cell designs: polycrystalline silicon, amorphous silicon, cadmium sulfide/copper sulfide frontwall, polycrystalline gallium arsenide MIS, and advanced concentrator-500X. Each of these five cells is screened individually assuming that they first come online in 1991, and that 25 GWe of peak capacity is online by the year 2000. A second computer screening assumes that each cell first comes online in 1991 and that each cell has 5 GWe of peak capacity by the year 2000, so that the total online cpacity for the five cells is 25 GWe. Based on a review of the preliminary basline screening results, suggestions were made for varying such parameters as the layer thickness, cell production processes, etc. The resulting PV cell characterizations were then screened again by the CMAP computer code. Earlier DOE sponsored work on the assessment of critical materials in PV cells conclusively identtified indium and gallium as warranting further investigation as to their availability. Therefore, this report includes a discussion of the future availability of gallium and indium. (WHK)

  1. Improving the efficiency of copper indium gallium (Di-selenide (CIGS solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

    Directory of Open Access Journals (Sweden)

    M. Burghoorn

    2014-12-01

    Full Text Available Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (Jsc and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-selenide (CIGS solar cells is also optically advantageous. Here, we experimentally demonstrate that the Jsc and efficiency of CIGS solar cells with an absorber layer thickness (dCIGS of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (nresist = 1.792 vs. nAZO = 1.913 at 633 nm to avoid large optical losses at the resist-AZO interface. On average, Jsc increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%. No trend towards a larger relative increase in Jsc with decreasing dCIGS was observed. Ergo, the increase in Jsc can be fully explained by the reduction in reflection, and we did not observe any increase in Jsc based on an increased photon path length.

  2. Improving the efficiency of copper indium gallium (Di-)selenide (CIGS) solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

    Energy Technology Data Exchange (ETDEWEB)

    Burghoorn, M.; Kniknie, B.; Deelen, J. van; Ee, R. van [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Xu, M. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Delft University of Technology, Optics Group, Van der Waalsweg 8, 2628 CH, Delft (Netherlands); Vroon, Z. [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); Zuyd Hogeschool, Nieuw Eyckholt 300, 6419 DJ, Heerlen (Netherlands); Belt, R. van de [Kriya Materials BV, Urmonderbaan 22, 6167 RD, Geleen (Netherlands); Buskens, P., E-mail: pascal.buskens@tno.nl, E-mail: buskens@dwi.rwth-aachen.de [The Netherlands Organisation for Applied Scientific Research (TNO), De Rondom 1, 5612 AP, Eindhoven (Netherlands); DWI – Leibniz Institute for Interactive Materials, Forckenbeckstrasse 50, 52056, Aachen (Germany)

    2014-12-15

    Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (J{sub sc}) and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-)selenide (CIGS) solar cells is also optically advantageous. Here, we experimentally demonstrate that the J{sub sc} and efficiency of CIGS solar cells with an absorber layer thickness (d{sub CIGS}) of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (n{sub resist} = 1.792 vs. n{sub AZO} = 1.913 at 633 nm) to avoid large optical losses at the resist-AZO interface. On average, J{sub sc} increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%). No trend towards a larger relative increase in J{sub sc} with decreasing d{sub CIGS} was observed. Ergo, the increase in J{sub sc} can be fully explained by the reduction in reflection, and we did not observe any increase in J{sub sc} based on an increased photon path length.

  3. Improving the efficiency of copper indium gallium (Di-)selenide (CIGS) solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

    Science.gov (United States)

    Burghoorn, M.; Kniknie, B.; van Deelen, J.; Xu, M.; Vroon, Z.; van Ee, R.; van de Belt, R.; Buskens, P.

    2014-12-01

    Textured transparent conductors are widely used in thin-film silicon solar cells. They lower the reflectivity at interfaces between different layers in the cell and/or cause an increase in the path length of photons in the Si absorber layer, which both result in an increase in the number of absorbed photons and, consequently, an increase in short-circuit current density (Jsc) and cell efficiency. Through optical simulations, we recently obtained strong indications that texturing of the transparent conductor in copper indium gallium (di-)selenide (CIGS) solar cells is also optically advantageous. Here, we experimentally demonstrate that the Jsc and efficiency of CIGS solar cells with an absorber layer thickness (dCIGS) of 0.85 μm, 1.00 μm and 2.00 μm increase through application of a moth-eye textured resist with a refractive index that is sufficiently similar to AZO (nresist = 1.792 vs. nAZO = 1.913 at 633 nm) to avoid large optical losses at the resist-AZO interface. On average, Jsc increases by 7.2%, which matches the average reduction in reflection of 7.0%. The average relative increase in efficiency is slightly lower (6.0%). No trend towards a larger relative increase in Jsc with decreasing dCIGS was observed. Ergo, the increase in Jsc can be fully explained by the reduction in reflection, and we did not observe any increase in Jsc based on an increased photon path length.

  4. Construction of Gallium Point at NMIJ

    Science.gov (United States)

    Widiatmo, J. V.; Saito, I.; Yamazawa, K.

    2017-03-01

    Two open-type gallium point cells were fabricated using ingots whose nominal purities are 7N. Measurement systems for the realization of the melting point of gallium using these cells were built. The melting point of gallium is repeatedly realized by means of the measurement systems for evaluating the repeatability. Measurements for evaluating the effect of hydrostatic pressure coming from the molten gallium existing during the melting process and the effect of gas pressure that fills the cell were also performed. Direct cell comparisons between those cells were conducted. This comparison was aimed to evaluate the consistency of each cell, especially related to the nominal purity. Direct cell comparison between the open-type and the sealed-type gallium point cell was also conducted. Chemical analysis was conducted using samples extracted from ingots used in both the newly built open-type gallium point cells, from which the effect of impurities in the ingot was evaluated.

  5. Homoepitaxial n-core: p-shell gallium nitride nanowires: HVPE overgrowth on MBE nanowires.

    Science.gov (United States)

    Sanders, Aric; Blanchard, Paul; Bertness, Kris; Brubaker, Matthew; Dodson, Christopher; Harvey, Todd; Herrero, Andrew; Rourke, Devin; Schlager, John; Sanford, Norman; Chiaramonti, Ann N; Davydov, Albert; Motayed, Abhishek; Tsvetkov, Denis

    2011-11-18

    We present the homoepitaxial growth of p-type, magnesium doped gallium nitride shells by use of halide vapor phase epitaxy (HVPE) on n-type gallium nitride nanowires grown by plasma-assisted molecular beam epitaxy (MBE). Scanning electron microscopy shows clear dopant contrast between the core and shell of the nanowire. The growth of magnesium doped nanowire shells shows little or no effect on the lattice parameters of the underlying nanowires, as measured by x-ray diffraction (XRD). Photoluminescence measurements of the nanowires show the appearance of sub-bandgap features in the blue and the ultraviolet, indicating the presence of acceptors. Finally, electrical measurements confirm the presence of electrically active holes in the nanowires.

  6. Microstructural investigations of manganese-doped gallium nitride by modern methods of high resolution and analytical transmission electron microscopy; Mikrostrukturelle Untersuchungen an Mangan-dotiertem Galliumnitrid mittels fortgeschrittener Methoden der hochaufloesenden und analytischen Transmissionselektronenmikroskopie

    Energy Technology Data Exchange (ETDEWEB)

    Niermann, T.

    2006-10-30

    The magnetic properties of a diluted magnetic semiconductor depend on the microstructure of the material. In this work transmission electron microscopy was applied to Mn-doped GaN to investigate the incorporation of Mn and the occurring crystal defects. The novel method of object wave reconstruction was used for the imaging of extended defects. This technique allowed the observation of core structures of various defects. The strain fields of these defects were measured using geometric phase analysis. Precipitates of GaMn{sub 3}N were identified by analytical measurements. A further investigation of material free of precipitates revealed an inhomogeneous distribution of the Mn, which is reported for the first time. The ratio between substitutional and interstitial incorporation of Mn was measured by angular resolved X-ray spectroscopy. The Mn was found predominantly on the substitutional site. (orig.)

  7. Optical control of gallium nanoparticle growth

    Science.gov (United States)

    MacDonald, K. F.; Fedotov, V. A.; Pochon, S.; Ross, K. J.; Stevens, G. C.; Zheludev, N. I.; Brocklesby, W. S.; Emel'yanov, V. I.

    2002-03-01

    We report that low-intensity light can dramatically influence and regulate the nanoparticle self-assembly process: Illumination of a substrate exposed to a beam of gallium atoms results in the formation of gallium nanoparticles with a relatively narrow size distribution. Very low light intensities, below the threshold for thermally induced evaporation, exert considerable control over nanoparticle formation.

  8. Study of Nitrogen terminated doped zigzag GNR FET exhibiting negative differential resistance

    Science.gov (United States)

    Gupta, Santosh Kumar; Jaiswal, Girija Nandan

    2015-10-01

    This paper presents the study of Gallium and Aluminum doped Nitrogen terminated zigzag Graphene Nano Ribbon (GNR) FET with high-k dielectric. The GNR FET structure has been designed and simulated using Quantumwise Atomistix Toolkit software package. The presented GNR FET with n-type (Nitrogen doped) electrodes and p-type (Gallium or Aluminum doped) scattering region are simulated and analyzed using Density Functional Theory combined with NEGF formalism and Device Density of States (DDOS). The device shows a negative differential resistance phenomenon which can be controlled by the gate of the zigzag GNR FET. It is found that doping of Gallium and Aluminum in scattering region provides higher drain current, higher ION/IOFF and IP/IV ratios as compared to that of Boron doped zigzag GNR FET. The potential applications of the device are in logical, high frequency, and memory devices.

  9. Gallium-67 citrate scan in extrapulmonary tuberculosis

    Energy Technology Data Exchange (ETDEWEB)

    Lin Wanyu [Taichung Veterans General Hospital (Taiwan). Dept. of Nuclear Medicine; Hsieh Jihfang [Chi-Mei Foundation Hospital, Tainan (Taiwan)

    1999-07-01

    Aim: Whole-body gallium scan was performed to evaluate the usefulness of gallium scan for detecting extrapulmonary tuberculosis (TB) lesions. Methods: Thirty-seven patients with extrapulmonary TB were included in this study. Four patients were found to have two lesions. Totally, 41 lesions were identified, including 19 TB arthritis, 8 spinal TB, 5 TB meningitis, 3 TB lymphadenopathy, 2 TB pericarditis, 1 TB peritonitis, 1 intestinal TB, 1 skin TB and 1 renal TB. Results: Of the 41 extrapulmonary TB lesions, gallium scan detected 32 lesions with a sensitivity of 78%. All the patients with TB meningitis showed negative gallium scan. When the five cases of TB meningitis were excluded, the detection sensitivity of gallium scan increased to 88.9% (32/36). Conclusion: Our data revealed that gallium scan is a convenient and useful method for evaluating extrapulmonary TB lesions other than TB-meningitis. We suggest that gallium scan be included in the clinical routine for patients with suspected extrapulmonary TB. (orig.) [German] Ziel: Es wurden Ganzkoerper-Gallium-Szintigramme angefertigt, um den Nutzen der Gallium-Szintigraphie zur Erfassung von extrapulmonalen Tuberkuloseherden (TB) zu erfassen. Methoden: 37 Patienten mit extrapulmonaler TB wurden eingeschlossen. 4 Patienten hatten 2 Laesionen. Insgesamt wurden 41 Laesionen identifiziert, hierunter 19 TB-Arthritis, 8 spinale TB, 5 TB-Meningitis, 3 TB-Lymphadenopathie, 2 TB-Perikarditis, 1 TB-Peritonitis, 1 intestinale TB, 1 Haut-TB und eine Nieren-TB. Ergebnisse: Von den 41 extrapulmonalen TB-Herden erfasste die Gallium-Szintigraphie 32 Herde mit einer Sensitivitaet von 78%. Alle Patienten mit TB-Meningitis zeigten einen negativen Gallium-Scan. Wenn die 5 Faelle mit TB-Meningitis ausgeschlossen wurden, stieg die Sensitivititaet der Gallium-Szintigraphie auf 88,9% (32/36). Schlussfolgerung: Die Daten zeigen, dass die Gallium-Szintigraphie eine einfache und nuetzliche Methode zur Erfassung extrapulmonaler TB-Herde ist

  10. A theoretical study of H{sub 2}S adsorption on graphene doped with B, Al and Ga

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Sheetal; Verma, A.S., E-mail: ajay_phy@rediffmail.com

    2013-10-15

    An effort has been made to exploit the adsorption potential of pure and doped graphene for H{sub 2}S molecule using density functional theory (DFT) modelling. Boron, aluminium and gallium atoms (IIIB) are used as dopant. For each pure and doped graphene system optimum position of adsorbed H{sub 2}S molecule is determined and adsorption energies are calculated. Further electronic properties are investigated by the analysis of Mulliken's charges and energy band-structures. The results indicate that H{sub 2}S molecule weakly binds to the pure graphene and boron doped graphene with small adsorption values; on the other hand aluminium doped graphene and gallium doped graphene have large adsorption energies values and binding distances typical for the chemisorptions. Local curvature in aluminium and gallium doped graphene is mainly responsible for the increased reactivity.

  11. Strategic Review of Arsenide, Phosphide and Nitride MOSFETs

    Directory of Open Access Journals (Sweden)

    Gourab Dutta

    2011-01-01

    Full Text Available Metal oxide semiconductor field effect transistor used as an amplifier and switch uses Si primarily as a channel material for its very stable oxide SiO2. In-spite of many advantages there are some restrictions for Si MOS, so the world is approaching towards compound semiconductor for higher frequency and current. The development of compound semiconductor metal oxide semiconductor is also facing critical problems due to the lack of availability of proper gate oxide material. Research is being conducted on arsenide and phosphide metal oxide semiconductor field effect transistor. Nitride channel MOS are in focus due to their high band gap, high current and high temperature uses.

  12. Indium gallium nitride multijunction solar cell simulation using silvaco atlas

    OpenAIRE

    Garcia, Baldomero

    2007-01-01

    This thesis investigates the potential use of wurtzite Indium Gallium Nitride as photovoltaic material. Silvaco Atlas was used to simulate a quad-junction solar cell. Each of the junctions was made up of Indium Gallium Nitride. The band gap of each junction was dependent on the composition percentage of Indium Nitride and Gallium Nitride within Indium Gallium Nitride. The findings of this research show that Indium Gallium Nitride is a promising semiconductor for solar cell use. United...

  13. Bismuth incorporation into gallium phosphide

    Energy Technology Data Exchange (ETDEWEB)

    Jena, Puru [Virginia Commonwealth Univ. (United States); Kandalam, Anil K. [West Chester Univ. of Pennsylvania (United States); Christian, Theresa M. [National Renewable Energy Lab. (United States); Beaton, Daniel A. [National Renewable Energy Lab. (United States); Mascarenhas, Angelo [National Renewable Energy Lab. (United States); Alberi, Kirstin [National Renewable Energy Lab. (United States)

    2016-12-21

    Gallium phosphide bismide (GaP1-xBix) epilayers with bismuth fractions from 0.9% to 3.2%, as calculated from lattice parameter measurements, were studied with Rutherford backscattering spectrometry (RBS) to directly measure bismuth incorporation. The total bismuth fractions found by RBS were higher than expected from the lattice parameter calculations. Furthermore, in one analyzed sample grown by molecular beam epitaxy at 300 degrees C, 55% of incorporated bismuth was found to occupy interstitial sites. We discuss implications of this high interstitial incorporation fraction and its possible relationship to x-ray diffraction and photoluminescence measurements of GaP0.99Bi0.01.

  14. Arsenic (III, V), indium (III), and gallium (III) toxicity to zebrafish embryos using a high-throughput multi-endpoint in vivo developmental and behavioral assay.

    Science.gov (United States)

    Olivares, Christopher I; Field, Jim A; Simonich, Michael; Tanguay, Robert L; Sierra-Alvarez, Reyes

    2016-04-01

    Gallium arsenide (GaAs), indium gallium arsenide (InGaAs) and other III/V materials are finding increasing application in microelectronic components. The rising demand for III/V-based products is leading to increasing generation of effluents containing ionic species of gallium, indium, and arsenic. The ecotoxicological hazard potential of these streams is unknown. While the toxicology of arsenic is comprehensive, much less is known about the effects of In(III) and Ga(III). The embryonic zebrafish was evaluated for mortality, developmental abnormalities, and photomotor response (PMR) behavior changes associated with exposure to As(III), As(V), Ga(III), and In(III). The As(III) lowest observable effect level (LOEL) for mortality was 500 μM at 24 and 120 h post fertilization (hpf). As(V) exposure was associated with significant mortality at 63 μM. The Ga(III)-citrate LOEL was 113 μM at 24 and 120 hpf. There was no association of significant mortality over the tested range of In(III)-citrate (56-900 μM) or sodium citrate (213-3400 μM) exposures. Only As(V) resulted in significant developmental abnormalities with LOEL of 500 μM. Removal of the chorion prior to As(III) and As(V) exposure was associated with increased incidence of mortality and developmental abnormality suggesting that the chorion may normally attenuate mass uptake of these metals by the embryo. Finally, As(III), As(V), and In(III) caused PMR hypoactivity (49-69% of control PMR) at 900-1000 μM. Overall, our results represent the first characterization of multidimensional toxicity effects of III/V ions in zebrafish embryos helping to fill a significant knowledge gap, particularly in Ga(III) and In(III) toxicology.

  15. Manganese Atom Ordered Monolayer on Wurtzite Gallium Nitride

    Science.gov (United States)

    Chinchore, Abhijit; Wang, Kangkang; Lin, Wenzhi; Pak, Jeongihm; Liu, Yinghao; Smith, Arthur

    2009-03-01

    While transition-metal-doped gallium nitride (GaN) thin films have been explored as potential dilute magnetic semiconductor bulk layers, the structural and magnetic effects of various transition metal adatoms on GaN surfaces are not even well understood. In this work, we investigate the sub-monolayer deposition of manganese (Mn) onto the N-polar wurtzite GaN (000-1) 1x1 surface. The growth is monitored in-situ using reflection high energy electron diffraction (RHEED). A fresh GaN(000-1) 1x1 surface is prepared by rf nitrogen plasma-assisted MBE followed by annealing to remove excess gallium adatoms. The atomically flat GaN surface, held at 200^o C, is then exposed to submonolayer doses of Mn. The deposition rate is maintained at 0.007 ML per second, and a 3x pattern develops along [10-10]; whereas, only 1x is seen along [11-20]. Analysis of the RHEED pattern and subsequent modeling indicates a 3 x3 R 30^o structure consisting of 2/3 ML Mn atoms in a row-like arrangement having spacing 3a/2 along rows and 3a/2 between rows. Scanning tunneling microscopy/spectroscopy studies are currently underway to explore this surface further. This work is supported by DOE (Grant No.DE-FG02-06ER46317) and NSF (Grant No. 0730257).

  16. Characterization and modeling of the intrinsic properties of 1.5-micrometer gallium indium nitrogen arsenic antimonide/gallium arsenide laser

    Science.gov (United States)

    Goddard, Lynford

    2005-12-01

    Low cost access to optical communication networks is needed to satisfy the rapidly increasing demands of home-based high-speed Internet. Existing light sources in the low-loss 1.2--1.6mum telecommunication wavelength bandwidth are prohibitively expensive for large-scale deployment, e.g. incorporation in individual personal computers. Recently, we have extended the lasing wavelength of room-temperature CW GaInNAs(Sb) lasers grown monolithically on GaAs by MBE up to 1.52mum in an effort to replace the traditional, more expensive, InP-based devices. Besides lower cost wafers, GaInNAs(Sb) opto-electronic devices have fundamental material advantages over InP-based devices: a larger conduction band offset which reduces temperature sensitivity and enhances differential gain, a lattice match to a material with a large refractive index contrast, i.e. AlAs, which decreases the necessary number of mirror pairs in DBRs for VCSELs, and native oxide apertures for current confinement. High performance GaInNAs(Sb) edge-emitting lasers, VCSELs, and DFB lasers have been demonstrated throughout the entire telecommunication band. In this work, we analyze the intrinsic properties of the GaInNAsSb material system, e.g. recombination, gain, band structure and renormalization, and efficiency. Theoretical modeling is performed to calculate a map of the bandgap and effective masses for various material compositions. We also present device performance results, such as: room temperature CW threshold densities below 450A/cm2, quantum efficiencies above 50%, and over 425mW of total power from a SQW laser when mounted epi-up and minimally packaged. These results are generally 2--4x better than previous world records for GaAs based devices at 1.5mum. The high CW power and low threshold exhibited by these SQW lasers near 1.5mum make feasible many novel applications, such as broadband Raman fiber amplifiers and uncooled WDM at the chip scale. Device reliability of almost 500 hours at 200mW CW output power has also been demonstrated. Comparative experiments using innovative characterization techniques, such as: the multiple section absorption/gain method to explore the band structure, as well as the Z-parameter to analyze the dominant recombination processes, have identified the physical mechanisms responsible for improved performance. Also, by measuring the temperature dependence of relevant laser parameters, we have been able to simulate device operation while varying temperature and device geometry.

  17. Lattice parameters guide superconductivity in iron-arsenides

    Science.gov (United States)

    Konzen, Lance M. N.; Sefat, Athena S.

    2017-03-01

    The discovery of superconducting materials has led to their use in technological marvels such as magnetic-field sensors in MRI machines, powerful research magnets, short transmission cables, and high-speed trains. Despite such applications, the uses of superconductors are not widespread because they function much below room-temperature, hence the costly cooling. Since the discovery of Cu- and Fe-based high-temperature superconductors (HTS), much intense effort has tried to explain and understand the superconducting phenomenon. While no exact explanations are given, several trends are reported in relation to the materials basis in magnetism and spin excitations. In fact, most HTS have antiferromagnetic undoped ‘parent’ materials that undergo a superconducting transition upon small chemical substitutions in them. As it is currently unclear which ‘dopants’ can favor superconductivity, this manuscript investigates crystal structure changes upon chemical substitutions, to find clues in lattice parameters for the superconducting occurrence. We review the chemical substitution effects on the crystal lattice of iron-arsenide-based crystals (2008 to present). We note that (a) HTS compounds have nearly tetragonal structures with a-lattice parameter close to 4 Å, and (b) superconductivity can depend strongly on the c-lattice parameter changes with chemical substitution. For example, a decrease in c-lattice parameter is required to induce ‘in-plane’ superconductivity. The review of lattice parameter trends in iron-arsenides presented here should guide synthesis of new materials and provoke theoretical input, giving clues for HTS.

  18. Synchrotron X-Ray Fluorescence Microscopy of Gallium in Bladder Tissue following Gallium Maltolate Administration during Urinary Tract Infection

    OpenAIRE

    Ball, Katherine R.; Sampieri, Francesca; Chirino, Manuel; Hamilton, Don L.; Blyth, Robert I. R.; Sham, Tsun-Kong; Dowling, Patricia M.; Thompson, Julie

    2013-01-01

    A mouse model of cystitis caused by uropathogenic Escherichia coli was used to study the distribution of gallium in bladder tissue following oral administration of gallium maltolate during urinary tract infection. The median concentration of gallium in homogenized bladder tissue from infected mice was 1.93 μg/g after daily administration of gallium maltolate for 5 days. Synchrotron X-ray fluorescence imaging and X-ray absorption spectroscopy of bladder sections confirmed that gallium arrived ...

  19. Optical Bistable Arrays: Prospects for Ultimate Performances,

    Science.gov (United States)

    OPTICAL SWITCHING, *OPTICAL INTERFEROMETERS, CAVITIES, IMPEDANCE, IMPEDANCE MATCHING , INTENSITY, LAYERS, MATERIALS, MIRRORS, OPTIMIZATION, PARAMETERS, REDUCTION, FRANCE, BISTABLE DEVICES, GALLIUM ARSENIDES, ALUMINUM GALLIUM ARSENIDES, HETEROJUNCTIONS.

  20. Gallium Oxide Nanostructures for High Temperature Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Chintalapalle, Ramana V. [Univ. of Texas, El Paso, TX (United States)

    2015-04-30

    Gallium oxide (Ga2O3) thin films were produced by sputter deposition by varying the substrate temperature (Ts) in a wide range (Ts=25-800 °C). The structural characteristics and electronic properties of Ga2O3 films were evaluated using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), Rutherford backscattering spectrometry (RBS) and spectrophotometric measurements. The effect of growth temperature is significant on the chemistry, crystal structure and morphology of Ga2O3 films. XRD and SEM analyses indicate that the Ga2O3 films grown at lower temperatures were amorphous while those grown at Ts≥500 oC were nanocrystalline. RBS measurements indicate the well-maintained stoichiometry of Ga2O3 films at Ts=300-800 °C. The electronic structure determination indicated that the nanocrystalline Ga2O3films exhibit a band gap of ~5 eV. Tungsten (W) incorporated Ga2O3 films were produced by co-sputter deposition. W-concentration was varied by the applied sputtering-power. No secondary phase formation was observed in W-incorporated Ga2O3 films. W-induced effects were significant on the structure and electronic properties of Ga2O3 films. The band gap of Ga2O3 films without W-incorporation was ~5 eV. Oxygen sensor characteristics evaluated using optical and electrical methods indicate a faster response in W-doped Ga2O3 films compared to intrinsic Ga2O3 films. The results demonstrate the applicability of both intrinsic and W-doped Ga-oxide films for oxygen sensor application at temperatures ≥700 °C.

  1. The surface tension of liquid gallium

    Science.gov (United States)

    Hardy, S. C.

    1985-01-01

    The surface tension of liquid gallium has been measured using the sessile drop technique in an Auger spectrometer. The experimental method is described. The surface tension in mJ/sq m is found to decrease linearly with increasing temperature and may be represented as 708-0.66(T-29.8), where T is the temperature in centigrade. This result is of interest because gallium has been suggested as a model fluid for Marangoni flow experiments. In addition, the surface tension is of technological significance in the processing of compound semiconductors involving gallium.

  2. Optical and Electrical Characterization of Melt-Grown Bulk Indium Gallium Arsenide and Indium Arsenic Phosphide Alloys

    Science.gov (United States)

    2011-03-01

    constant match and mismatch effects on the quality of crystal. Bulk crystal growth typically uses the Czochralski Method (melt). In this method , a...deviation and Michelson Fabry-Perot interferometry methods . The measured results of refractive indices, transport properties, bandgap energies, and...exhibit some random compositional fluctuations across the sample. A practical method of extracting bandgap energies directly from the FTIR

  3. Technology characteristics and concerns arising in the design and fabrication of an entire signal processor using gallium arsenide integrated circuits

    Science.gov (United States)

    Naused, Barbara A.; Samson, Mark L.; Schwab, Daniel J.; Gilbert, Barry K.

    Various GaAs transistor and gate technologies that have been developed since 1980 are analyzed. The characteristics of GaAs logic gates and ICs and the buffered FET logic, Shottky diode FET logic, direct coupled FET logic, and heterojunction integrated injection logic used to implement GaAs gate arrays of LSI complexity are described. The use of digital GaAs in a complex target signal processor, the Advanced Onboard Signal Processor (AOSP), is studied. Data from the testing of GaAs components for the AOSP at the wafer probe, package, and assembled circuit board levels are examined.

  4. Development of a unique laboratory standard indium gallium arsenide detector for the 500 to 1700 micron spectral region, phase 2

    Science.gov (United States)

    Ban, Vladimir S.; Olsen, Gregory H.

    1990-01-01

    In the course of this work, 5 mm diameter InGaAs pin detectors were produced which met or exceeded all of the goals of the program. The best results achieved were: shunt resistance of over 300 K ohms; rise time of less than 300 ns; contact resistance of less than 20 ohms; quantum efficiency of over 50 percent in the 0.5 to 1.7 micron range; and devices were maintained and operated at 125 C without deterioration for over 100 hours. In order to achieve the goals of this program, several major technological advances were realized, among them: successful design, construction and operation of a hydride VPE reactor capable of growing epitaxial layers on 2 inch diameter InP substrates with a capacity of over 8 wafers per day; wafer processing was upgraded to handle 2 inch wafers; a double layer Si3N4/SiO2 antireflection coating which enhances response over the 0.5 to 1.7 micron range was developed; a method for anisotropic, precisely controlled CH4/H2 plasma etching for enhancement of response at short wavelengths was developed; and electronic and optical testing methods were developed to allow full characterization of detectors with size and spectral response characteristics. On the basis of the work and results achieved in this program, it is concluded that large size, high shunt resistance, high quantum efficiency InGaAs pin detectors are not only feasible but also manufacturable on industrial scale. This device spans a significant portion of visible and near infrared spectral range and it will allow a single detector to be used for the 0.5 to 1.7 micron spectral region, rather than the presently used silicon (for 0.5 to 1.1 microns) and germanium (0.8 to 1.7 microns).

  5. Thin films of gallium arsenide on low-cost substrates. Final report, July 5, 1976--July 2, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, R.P.; Dapkus, P.D.; Dupuis, R.D.; Campbell, A.G.; Johnson, R.E.; Manasevit, H.M.; Moudy, L.A.; Yang, J.J.; Yingling, R.D.

    1977-08-01

    The metalorganic chemical vapor deposition (MO-CVD) technique has been applied to the growth of thin films of GaAs and GaAlAs on inexpensive polycrystalline or amorphous substrate materials (glasses, glass-ceramics, alumina ceramics, and metals) for use in fabrication of large-area low-cost photovoltaic device structures. Trimethylgallium (TMG), arsine (AsH/sub 3/), and trimethylaluminum (TMAl) are mixed in appropriate concentrations at room temperature in the gaseous state and pyrolyzed at the substrate, which is heated in a vertical reactor chamber to temperature in the range 600 to 800/sup 0/C, to produce the desired film composition and properties. Of ten candidate low-cost substrates initially identified for investigation, Corning Code 0317 glass and composites of CVD Ge/glass and sputtered Mo/glass were found to be the most satisfactory, the latter eventually serving as a reference substrate against which to compare the performance of other substrates. Single-crystal window-type solar cells, polycrystalline Schottky-barrier cells, and deposited-junction polycrystalline cells have been grown, fabricated, and characterized. Epitaxial GaAlAs/GaAs p-n junction cells with thin (approx. 500A) Ga/sub 0/ /sub 2/Al/sub 0/ /sub 8/As windows and GaAs:Zn - GaAs:Se junctions were made with AMO efficiencies as high as 12.8 percent with no AR coating. Schottky barrier cells with efficiencies of 2.25 percent AMO (no AR coating) have been made on n/n polycrystalline GaAs structures on Mo/glass composite substrates, with short-circuit current densities up to 12.5 mA/cm/sup 2/. Also, results of analyses of material and processing costs associated with fabrication of thin-film GaAlAs/GaAs solar cells by the MO-CVD process are discussed.

  6. Transient Velocity Assessment in Gallium Arsenide, and of Other GaAs Characteristics Related to Device Functions

    Science.gov (United States)

    2012-03-29

    RW-809 ^ C^> Scientific Program Officer: Mr . Sven A. Roosild, DARPA/DSO 1400 Wilson Blvd. Arlington, VA 22209 Contractor: Oregon Graduate...of acoustic phonons, non-parabolicity of the conduction band minimum and intervaliey scattering through the admixture of p-type states. He concluded...llarrlta 1985 LEC (HP) 50 5 Goutereaux et_ al. lUrrltt 1985 LEC (HP) 50 5 Ilakemore et_ al. MOCSEMHAD 1985 IXC (HP) 50 0.5 Dobrllla et al. MRS /5F0 1985

  7. Electrical detection of the biological interaction of a charged peptide via gallium arsenide junction-field-effect transistors

    Science.gov (United States)

    Lee, Kangho; Nair, Pradeep R.; Alam, Muhammad A.; Janes, David B.; Wampler, Heeyeon P.; Zemlyanov, Dmitry Y.; Ivanisevic, Albena

    2008-06-01

    GaAs junction-field-effect transistors (JFETs) are utilized to achieve label-free detection of biological interaction between a probe transactivating transcriptional activator (TAT) peptide and the target trans-activation-responsive (TAR) RNA. The TAT peptide is a short sequence derived from the human immunodeficiency virus-type 1 TAT protein. The GaAs JFETs are modified with a mixed adlayer of 1-octadecanethiol (ODT) and TAT peptide, with the ODT passivating the GaAs surface from polar ions in physiological solutions and the TAT peptide providing selective binding sites for TAR RNA. The devices modified with the mixed adlayer exhibit a negative pinch-off voltage (VP) shift, which is attributed to the fixed positive charges from the arginine-rich regions in the TAT peptide. Immersing the modified devices into a TAR RNA solution results in a large positive VP shift (>1 V) and a steeper subthreshold slope (˜80 mV/decade), whereas "dummy" RNA induced a small positive VP shift (˜0.3 V) without a significant change in subthreshold slopes (˜330 mV/decade). The observed modulation of device characteristics is analyzed with analytical modeling and two-dimensional numerical device simulations to investigate the electronic interactions between the GaAs JFETs and biological molecules.

  8. Electrical detection of the biological interaction of a charged peptide via gallium arsenide junction-field-effect transistors

    OpenAIRE

    Lee, Kangho; Nair, Pradeep R.; Alam, Muhammad A.; Janes, David B.; Wampler, Heeyeon P; Zemlyanov, Dmitry; Ivanisevic, Albena

    2008-01-01

    GaAs junction-field-effect transistors (JFETs) are utilized to achieve label-free detection of biological interaction between a probe transactivating transcriptional activator (TAT) peptide and the target trans-activation-responsive (TAR) RNA. The TAT peptide is a short sequence derived from the human immunodeficiency virus-type 1 TAT protein. The GaAs JFETs are modified with a mixed adlayer of 1-octadecanethiol (ODT) and TAT peptide, with the ODT passivating the GaAs surface from polar ions ...

  9. Gallium arsenide (GaAs) (001) after sublimation of arsenic (As) thin-film cap, by XPS

    Energy Technology Data Exchange (ETDEWEB)

    Engelhard, Mark H.; Lyubinetsky, Andre; Baer, Don R.

    2016-12-01

    Survey and high energy resolution spectra are reported for MBE grown GaAs (001) that had been capped with As. The As cap was removed by heating in situ prior to analysis. The current data expands upon the spectral regions previously reported in Surface Science Spectra. High energy resolution spectral features reported include: 2p, 3s, 3p, 3d, and L3M45M45 peaks for As; 2p, 3s, 3p, 3d, and L3M45M45 peaks for Ga; and the valance band region.

  10. Radiochemical separation of gallium by amalgam exchange

    Science.gov (United States)

    Ruch, R.R.

    1969-01-01

    An amalgam-exchange separation of radioactive gallium from a number of interfering radioisotopes has been developed. A dilute (ca. 0.3%) gallium amalgam is agitated with a slightly acidic solution of 72Ga3+ containing concentrations of sodium thiocyanate and either perchlorate or chloride. The amalgam is then removed and the radioactive gallium stripped by agitation with dilute nitric acid. The combined exchange yield of the perchlorate-thiocyanate system is 90??4% and that of the chloride-thiocyanate system is 75??4%. Decontamination yields of most of the 11 interfering isotopes studied were less than 0.02%. The technique is applicable for use with activation analysis for the determination of trace amounts of gallium. ?? 1969.

  11. Materials synthesis: Two-dimensional gallium nitride

    Science.gov (United States)

    Koratkar, Nikhil A.

    2016-11-01

    Graphene is used as a capping sheet to synthesize 2D gallium nitride by means of migration-enhanced encapsulation growth. This technique may allow the stabilization of 2D materials that are not amenable to synthesis by traditional methods.

  12. First principles predictions of intrinsic defects in aluminum arsenide, AlAs : numerical supplement.

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, Peter Andrew

    2012-04-01

    This Report presents numerical tables summarizing properties of intrinsic defects in aluminum arsenide, AlAs, as computed by density functional theory. This Report serves as a numerical supplement to the results published in: P.A. Schultz, 'First principles predictions of intrinsic defects in Aluminum Arsenide, AlAs', Materials Research Society Symposia Proceedings 1370 (2011; SAND2011-2436C), and intended for use as reference tables for a defect physics package in device models.

  13. Nanoscale photonics of structural transformations in gallium

    Science.gov (United States)

    Zheludev, Nikolay I.; Fedotov, V. A.; MacDonald, K. F.; Stevens, G. C.; Pochon, Sebastien C.; Woodford, M.

    2002-11-01

    We have found recently that Gallium, confined at an interface with silica, responds dramatically to low power optical excitation when held at temperatures close to its melting point (29.8oC). Intensities of just a few kW/cm2 can reversibly modulate the intensity (by up to 40%) and phase (by as much as several degrees) of reflected light as the result of a light-induced structural transition occurring in a layer of gallium of only a few nm thick. Here, we report that this concept - of achieving a nonlinearity via a light-induced transformation in a confined solid at a temperature close to a phase transition temperature - can also be applied to gallium nanoparticles. We present the transient all-optical switching characteristics of gallium nanoparticle films comprising particles, typically 80 nm in diameter, which were formed directly on the ends of optical fibers using a new light-assisted self-assembly technique. We also report, for the first time, that this light-induced structural transition in gallium confined at an interface with silica underlies a new mechanism for photoconductivity. In our opinion, the exploitation of the light-induced phase transition in gallium may be a means of enabling the development of nanoscale photonic devices.

  14. Methods for forming group III-arsenide-nitride semiconductor materials

    Science.gov (United States)

    Major, Jo S. (Inventor); Welch, David F. (Inventor); Scifres, Donald R. (Inventor)

    2002-01-01

    Methods are disclosed for forming Group III-arsenide-nitride semiconductor materials. Group III elements are combined with group V elements, including at least nitrogen and arsenic, in concentrations chosen to lattice match commercially available crystalline substrates. Epitaxial growth of these III-V crystals results in direct bandgap materials, which can be used in applications such as light emitting diodes and lasers. Varying the concentrations of the elements in the III-V crystals varies the bandgaps, such that materials emitting light spanning the visible spectra, as well as mid-IR and near-UV emitters, can be created. Conversely, such material can be used to create devices that acquire light and convert the light to electricity, for applications such as full color photodetectors and solar energy collectors. The growth of the III-V crystals can be accomplished by growing thin layers of elements or compounds in sequences that result in the overall lattice match and bandgap desired.

  15. Structural properties of pressure-induced structural phase transition of Si-doped GaAs by angular-dispersive X-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Kung-Liang [Industrial Technology Research Institute, Hsinchu (China); Lin, Chih-Ming; Lin, Yu-Sheng [National Hsinchu University of Education, Department of Applied Science, Hsinchu (China); Jian, Sheng-Rui [I-Shou University, Department of Materials Science and Engineering, Kaohsiung (China); Liao, Yen-Fa; Chuang, Yu-Chun [National Synchrotron Radiation Research Center, Hsinchu (China); Wang, Chuan-Sheng [Taipei Chengshih University of Science and Technology, Department of Mechanical Engineering, Taipei (China); Juang, Jenh-Yih [National Chiao Tung University, Department of Electrophysics, Hsinchu (China)

    2016-02-15

    Pressure-induced phase transitions in n-type silicon-doped gallium arsenide (GaAs:Si) at ambient temperature were investigated by using angular-dispersive X-ray diffraction (ADXRD) under high pressure up to around 18.6 (1) GPa, with a 4:1 (in volume ratio) methanol-ethanol mixture as the pressure-transmitting medium. In situ ADXRD measurements revealed that n-type GaAs:Si starts to transform from zinc-blende structure to an orthorhombic structure [GaAs-II phase], space group Pmm2, at 16.4 (1) GPa. In contrast to previous studies of pure GaAs under pressure, our results show no evidence of structural transition to Fmmm or Cmcm phase. The fitting of volume compression data to the third-order Birch-Murnaghan equation of state yielded that the zero-pressure isothermal bulk moduli and the first-pressure derivatives were 75 (3) GPa and 6.4 (9) for the B3 phase, respectively. After decompressing to the ambient pressure, the GaAs:Si appears to revert to the B3 phase completely. By fitting to the empirical relations, the Knoop microhardness numbers are between H{sub PK} = 6.21 and H{sub A} = 5.85, respectively, which are substantially smaller than the values of 7-7.5 for pure GaAs reported previously. A discontinuous drop in the pressure-dependent lattice parameter, N-N distances, and V/V{sub 0} was observed at a pressure of 11.5 (1) GPa, which was tentatively attributed to the pressure-induced dislocation activities in the crystal grown by vertical gradient freeze method. (orig.)

  16. Gallium-67 uptake in cutaneous lesions of mycosis fungoides

    Energy Technology Data Exchange (ETDEWEB)

    Nishimi, L.; Chen, D.C.; Ansari, A.N.; Siegel, M.E.

    1988-02-01

    The literature on gallium imaging in mycosis fungoides is limited and conflicting. A case of mycosis fungoides with increased uptake of Ga-67 in clinically noninfected skin lesions is reported. The literature regarding mycosis fungoides and gallium imaging is reviewed.

  17. Role of gallium and bone scintigraphy in disseminated coccidioidomycosis

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, A.J.; Braunstein, P.; Pais, M.J.

    1984-09-01

    The osseous lesions of disseminated coccidioidomycosis may be detected by bone but not by gallium scintigraphy or vice versa. This case emphasizes the need for performing both bone and gallium scans to avoid missing potentially serious bone lesions.

  18. Rare Earth Doped GaN Laser Structures Using Metal Modulated Epitaxy

    Science.gov (United States)

    2015-03-30

    Doped Gallium Nitride by Plasma Assisted MBE, Ph. D. Thesis in Electrical and Computer Engineering, 2007, Georgia Institute of Technology, Atlanta...PERCENT_SUPPORTEDNAME FTE Equivalent: Total Number: ...... ...... Inventions (DD882) Scientific Progress Gallium nitride is a well-known wide bandgap III/V...Rui Wang for generously sharing his knowledge and experience in MBE, SIMS and nitride semiconductors. The discussions I was fortunate enough to have

  19. Electron emitting device and method of making the same

    Science.gov (United States)

    Olsen, Gregory Hammond; Martinelli, Ramon Ubaldo; Ettenberg, Michael

    1977-04-19

    A substrate of single crystalline gallium arsenide has on a surface thereof a layer of single crystalline indium gallium phosphide. A layer of single crystalline gallium arsenide is on the indium gallium phosphide layer and a work function reducing material is on the gallium arsenide layer. The substrate has an opening therethrough exposing a portion of the indium gallium phosphide layer.

  20. Polarity Control and Doping in Aluminum Gallium Nitride

    Science.gov (United States)

    2013-06-01

    seems to go hand in hand with a decrease in resistivity. In other words, a more activated sample shows a more intense ABX transition as well as a...Al0.8Ga0.2N grown on c- oriented AlN single crystal substrates; Physica Status Solidi (c) 9 (3-4); 584-587 (2012). 5 Y. Taniyasu, M. Kasu and T. Makimoto ...emitting diodes; Nature 406 (6798); 865-868 (2000). 21 U. T. Schwarz and M. Kneissl; Nitride emitters go nonpolar; physica status solidi (RRL

  1. Single gallium nitride nanowire lasers.

    Science.gov (United States)

    Johnson, Justin C; Choi, Heon-Jin; Knutsen, Kelly P; Schaller, Richard D; Yang, Peidong; Saykally, Richard J

    2002-10-01

    There is much current interest in the optical properties of semiconductor nanowires, because the cylindrical geometry and strong two-dimensional confinement of electrons, holes and photons make them particularly attractive as potential building blocks for nanoscale electronics and optoelectronic devices, including lasersand nonlinear optical frequency converters. Gallium nitride (GaN) is a wide-bandgap semiconductor of much practical interest, because it is widely used in electrically pumped ultraviolet-blue light-emitting diodes, lasers and photodetectors. Recent progress in microfabrication techniques has allowed stimulated emission to be observed from a variety of GaN microstructures and films. Here we report the observation of ultraviolet-blue laser action in single monocrystalline GaN nanowires, using both near-field and far-field optical microscopy to characterize the waveguide mode structure and spectral properties of the radiation at room temperature. The optical microscope images reveal radiation patterns that correlate with axial Fabry-Perot modes (Q approximately 10(3)) observed in the laser spectrum, which result from the cylindrical cavity geometry of the monocrystalline nanowires. A redshift that is strongly dependent on pump power (45 meV microJ x cm(-2)) supports the idea that the electron-hole plasma mechanism is primarily responsible for the gain at room temperature. This study is a considerable advance towards the realization of electron-injected, nanowire-based ultraviolet-blue coherent light sources.

  2. Ambient temperature deposition of gallium nitride/gallium oxynitride from a deep eutectic electrolyte, under potential control.

    Science.gov (United States)

    Sarkar, Sujoy; Sampath, S

    2016-05-11

    A ternary, ionically conducting, deep eutectic solvent based on acetamide, urea and gallium nitrate is reported for the electrodeposition of gallium nitride/gallium indium nitride under ambient conditions; blue and white light emitting photoluminescent deposits are obtained under potential control.

  3. Paired-pulse facilitation achieved in protonic/electronic hybrid indium gallium zinc oxide synaptic transistors

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Li Qiang, E-mail: guoliqiang@ujs.edu.cn; Ding, Jian Ning; Huang, Yu Kai [Micro/Nano Science & Technology Center, Jiangsu University, Zhenjiang, 212013 (China); Zhu, Li Qiang, E-mail: lqzhu@nimte.ac.cn [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)

    2015-08-15

    Neuromorphic devices with paired pulse facilitation emulating that of biological synapses are the key to develop artificial neural networks. Here, phosphorus-doped nanogranular SiO{sub 2} electrolyte is used as gate dielectric for protonic/electronic hybrid indium gallium zinc oxide (IGZO) synaptic transistor. In such synaptic transistors, protons within the SiO{sub 2} electrolyte are deemed as neurotransmitters of biological synapses. Paired-pulse facilitation (PPF) behaviors for the analogous information were mimicked. The temperature dependent PPF behaviors were also investigated systematically. The results indicate that the protonic/electronic hybrid IGZO synaptic transistors would be promising candidates for inorganic synapses in artificial neural network applications.

  4. Structural, elastic, electronic properties and stability trends of 1111-like silicide arsenides and germanide arsenides MCuXAs (M = Ti, Zr, Hf; X = Si, Ge) from first principles

    Energy Technology Data Exchange (ETDEWEB)

    Bannikov, V.V.; Shein, I.R. [Institute of Solid State Chemistry, Ural Branch of the Russian Academy of Sciences, 620990 Ekaterinburg (Russian Federation); Ivanovskii, A.L., E-mail: ivanovskii@ihim.uran.ru [Institute of Solid State Chemistry, Ural Branch of the Russian Academy of Sciences, 620990 Ekaterinburg (Russian Federation)

    2012-08-25

    Highlights: Black-Right-Pointing-Pointer Silicide arsenides and germanide arsenides of Ti, Zr, Hf are probed from first principles. Black-Right-Pointing-Pointer Structural, elastic, electronic properties and stability trends are evaluated. Black-Right-Pointing-Pointer Bulk moduli of HfCuSiAs and HfCuGeAs are the largest among all 1111-like phases. Black-Right-Pointing-Pointer Chemical bonding is analyzed. - Abstract: The tetragonal (s.g. I4/nmm; no. 129) silicide arsenide ZrCuSiAs is well known as a structural type of the broad family of so-called 1111-like quaternary phases which includes now more than 150 representatives. These materials demonstrate a rich variety of outstanding physical properties (from p-type transparent semiconductors to high-temperature Fe-based superconductors) and attracted a great interest as promising candidates for a broad range of applications. At the same time, the data about the electronic and elastic properties of the ZrCuSiAs phase itself, as well as of related silicide arsenides and germanide arsenides are still very limited. Here for a series of six isostructural and isoelectronic 1111-like phases which includes both synthesized (ZrCuSiAs, HfCuSiAs, ZrCuGeAs, and HfCuGeAs) and hypothetical (TiCuSiAs and TiCuGeAs) materials, systematical studies of their structural, elastic, electronic properties and stability trends are performed by means of first-principles calculations.

  5. Gallium-67 scintigraphy in patients with hemochromatosis treated by deferoxamine

    Energy Technology Data Exchange (ETDEWEB)

    Nagamachi, Shigeki; Hoshi, Hiroaki; Jinnouchi, Seishi; Ono, Seiji; Watanabe, Katsushi

    1988-05-01

    Gallium scintigraphy was performed as an aid for determining the presence or absence of malignant neoplasm in two patients with hemochromatosis treated by deferoxamine. However, gallium scan images could not be obtained. So gallium scintigraphy was performed once more to investigate the cause of low activity. Both patients had heavy urinary excretion of gallium in the first 24 hrs after the injection, and activity was very low on the day of examination. This phenomenon may be attributed to the effect of deferoxamine which is highly bound to the gallium.

  6. Chlorine and gallium solar neutrino experiments

    Science.gov (United States)

    Bahcall, J. N.; Cleveland, B. T.; Davis, R., Jr.; Rowley, J. K.

    1985-05-01

    The authors reevaluate the expected capture rates and their uncertainties for the chlorine and gallium solar neutrino experiments using improved laboratory data and new theoretical calculations. They also derive a minimum value for the flux of solar neutrinos that is expected provided only (1) that the sun is currently producing energy by fusing light nuclei at the rate that it is emitting energy in the form of photons from its surface and (2) that nothing happens to solar neutrinos on their way to earth. These results are used - together with Monte Carlo simulations - to determine how much gallium is required for a solar neutrino experiment.

  7. Evidence for three-dimensional Fermi-surface topology of the layered electron-doped iron superconductor Ba(Fe1 xCox)2As2

    Energy Technology Data Exchange (ETDEWEB)

    Vilmercati, P. [University of Tennessee, Knoxville (UTK); Fedorov, A. V. [Lawrence Berkeley National Laboratory (LBNL); Vobornik, I. [TASC National Laboratory, Trieste, Italy; Manju, U. [TASC National Laboratory, Trieste, Italy; Panaccione, G. [TASC National Laboratory, Trieste, Italy; Goldoni, A. [Sincrotrone Trieste, Basovizza, Italy; Safa-Sefat, Athena [ORNL; McGuire, Michael A [ORNL; Sales, Brian C [ORNL; Jin, Rongying [ORNL; Mandrus, David [ORNL; Singh, David J [ORNL; Mannella, Norman [ORNL

    2009-01-01

    The electronic structure of electron doped iron-arsenide superconductors Ba(Fe{sub 1-x}Co{sub x}){sub 2}As{sub 2} has been measured with Angle Resolved Photoemission Spectroscopy. The data reveal a marked photon energy dependence of points in momentum space where the bands cross the Fermi energy, a distinctive and direct signature of three-dimensionality in the Fermi surface topology. By providing a unique example of high temperature superconductivity hosted in layered compounds with three-dimensional electronic structure, these findings suggest that the iron-arsenides are unique materials, quite different from the cuprates high temperature superconductors.

  8. Synchrotron X-ray fluorescence microscopy of gallium in bladder tissue following gallium maltolate administration during urinary tract infection.

    Science.gov (United States)

    Ball, Katherine R; Sampieri, Francesca; Chirino, Manuel; Hamilton, Don L; Blyth, Robert I R; Sham, Tsun-Kong; Dowling, Patricia M; Thompson, Julie

    2013-11-01

    A mouse model of cystitis caused by uropathogenic Escherichia coli was used to study the distribution of gallium in bladder tissue following oral administration of gallium maltolate during urinary tract infection. The median concentration of gallium in homogenized bladder tissue from infected mice was 1.93 μg/g after daily administration of gallium maltolate for 5 days. Synchrotron X-ray fluorescence imaging and X-ray absorption spectroscopy of bladder sections confirmed that gallium arrived at the transitional epithelium, a potential site of uropathogenic E. coli infection. Gallium and iron were similarly but not identically distributed in the tissues, suggesting that at least some distribution mechanisms are not common between the two elements. The results of this study indicate that gallium maltolate may be a suitable candidate for further development as a novel antimicrobial therapy for urinary tract infections caused by uropathogenic E. coli.

  9. Synchrotron X-Ray Fluorescence Microscopy of Gallium in Bladder Tissue following Gallium Maltolate Administration during Urinary Tract Infection

    Science.gov (United States)

    Sampieri, Francesca; Chirino, Manuel; Hamilton, Don L.; Blyth, Robert I. R.; Sham, Tsun-Kong; Dowling, Patricia M.; Thompson, Julie

    2013-01-01

    A mouse model of cystitis caused by uropathogenic Escherichia coli was used to study the distribution of gallium in bladder tissue following oral administration of gallium maltolate during urinary tract infection. The median concentration of gallium in homogenized bladder tissue from infected mice was 1.93 μg/g after daily administration of gallium maltolate for 5 days. Synchrotron X-ray fluorescence imaging and X-ray absorption spectroscopy of bladder sections confirmed that gallium arrived at the transitional epithelium, a potential site of uropathogenic E. coli infection. Gallium and iron were similarly but not identically distributed in the tissues, suggesting that at least some distribution mechanisms are not common between the two elements. The results of this study indicate that gallium maltolate may be a suitable candidate for further development as a novel antimicrobial therapy for urinary tract infections caused by uropathogenic E. coli. PMID:23877680

  10. Infrared absorption study of neutron-transmutation-doped germanium

    Science.gov (United States)

    Park, I. S.; Haller, E. E.

    1988-01-01

    Using high-resolution far-infrared Fourier transform absorption spectroscopy and Hall effect measurements, the evolution of the shallow acceptor and donor impurity levels in germanium during and after the neutron transmutation doping process was studied. The results show unambiguously that the gallium acceptor level concentration equals the concentration of transmutated Ge-70 atoms during the whole process indicating that neither recoil during transmutation nor gallium-defect complex formation play significant roles. The arsenic donor levels appear at full concentration only after annealing for 1 h at 450 C. It is shown that this is due to donor-radiation-defect complex formation. Again, recoil does not play a significant role.

  11. Synergistic Extraction of Gallium for Sulfate Solution

    Institute of Scientific and Technical Information of China (English)

    DENGTong; HUANGLijuan; 等

    2002-01-01

    A novel extractant mixture, di-2-ethylhexyl phosphate (DEHPA) plus HX, was propose and tested for recovering gallium from sulfate solution.It was found that the extraction capacity of DEPHA for gallium from sulfate solution could be enhanced significantly due to the synergistic effect of acidix extractant HX. Gallium extraction is negligible below pH 0 and highly sensitive to pH of aqueous phase in the range from 0 to 1, and satisfactory extraction can be gained at pH>1. More than 96% Ga extraction was obtained using 15% DEHPA plus 2% HX. Although Fe(Ⅲ) was found to be extracted preferentially to Ga (Ⅲ), effective extraction of Ga (Ⅲ) was possible by reducing ferric to the ferrous state prior to extraction. A loaded organic phase containing 0.48g·L-1 Ga could be produced from solution of 0.12g·L-1 Ga at A/O ratio of 4:1 via three mixer-settler operation stages. Gallium was stripped quantitatively from the loaded organic phase with 1.5mol·L-1 of sulfuric acid.

  12. Anisotropy of the magnetic susceptibility of gallium

    Science.gov (United States)

    Pankey, T.

    1960-01-01

    The bulk magnetic susceptibilities of single gallium crystals and polycrystalline gallium spheres were measured at 25??C. The following anisotropic diamagnetic susceptibilities were found: a axis (-0.119??0. 001)??10-6 emu/g, b axis (-0.416??0.002)??10 -6 emu/g, and c axis (-0.229??0.001) emu/g. The susceptibility of the polycrystalline spheres, assumed to be the average value for the bulk susceptibility of gallium, was (-0.257??0.003)??10-6 emu/g at 25??C, and (-0.299??0.003)??10-6 emu/g at -196??C. The susceptibility of liquid gallium was (0.0031??0.001) ??10-6 emu/g at 30??C and 100??C. Rotational diagrams of the susceptibilities in the three orthogonal planes of the unit cell were not sinusoidal. The anisotropy in the single crystals was presumably caused by the partial overlap of Brillouin zone boundaries by the Fermi-energy surface. The large change in susceptibility associated with the change in state was attributed to the absence of effective mass influence in the liquid state. ?? 1960 The American Institute of Physics.

  13. Gallium Nitride Crystals: Novel Supercapacitor Electrode Materials.

    Science.gov (United States)

    Wang, Shouzhi; Zhang, Lei; Sun, Changlong; Shao, Yongliang; Wu, Yongzhong; Lv, Jiaxin; Hao, Xiaopeng

    2016-05-01

    A type of single-crystal gallium nitride mesoporous membrane is fabricated and its supercapacitor properties are demonstrated for the first time. The supercapacitors exhibit high-rate capability, stable cycling life at high rates, and ultrahigh power density. This study may expand the range of crystals as high-performance electrode materials in the field of energy storage.

  14. Optical and structural properties of chromium impurities in niobium–gallium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Costa, G.K.B. [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil); Departamento de Física, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro, RJ 22453-900 (Brazil); López, A. [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil); Carvalho, I.C.S. [Departamento de Física, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro, RJ 22453-900 (Brazil); Nakamura, O. [Instituto de Física, Universidade Federal da Bahia, Salvador, BA 40210-340 (Brazil); Cella, N. [Instituto Politécnico, Universidade do Estado do Rio de Janeiro, P.O. Box 97282, Nova Friburgo, RJ 28601-970 (Brazil); Sosman, L.P., E-mail: sosman@uerj.br [Instituto de Física, Universidade do Estado do Rio de Janeiro, Rio de Janeiro, RJ 20559-900 (Brazil)

    2014-12-15

    In this work, the optical properties of the gallium–niobium oxide doped with chromium ions were investigated. The samples were obtained by wet chemical and solid-state methods, investigated by X-ray powder diffraction and the data were refined by Rietveld methods. The morphology was determined by scanning electron microscope (SEM) images. The photoluminescence, excitation and photoacoustic measurements showed broad and intense bands in the red region of the spectrum, associated with energy transitions of chromium ions in octahedral sites. From the optical spectra and using the crystal field theory, the energy parameters were obtained. - Highlights: • Cr{sup 3+} doped niobium–gallium oxides were prepared by solid state reaction and wet chemical method. • We show bands in red region. • Spectra are associated to Cr{sup 3+} ions in octahedral sites.

  15. Gallium 67 scintigraphy in glomerular disease

    Energy Technology Data Exchange (ETDEWEB)

    Bakir, A.A.; Lopez-Majano, V.; Levy, P.S.; Rhee, H.L.; Dunea, G.

    1988-12-01

    To evaluate the diagnostic usefulness of gallium 67 scintigraphy in glomerular disease, 45 patients with various glomerulopathies, excluding lupus nephritis and renal vasculitis, were studied. Persistent renal visualization 48 hours after the gallium injection, a positive scintigram, was graded as + (less than), ++ (equal to), and +++ (greater than) the hepatic uptake. Positive scintigrams were seen in ten of 16 cases of focal segmental glomerulosclerosis, six of 11 cases of proliferative glomerulonephritis, and one case of minimal change, and one of two cases of membranous nephropathy; also in three of six cases of sickle glomerulopathy, two cases of diabetic neuropathy, one of two cases of amyloidosis, and one case of mild chronic allograft rejection. The 25 patients with positive scans were younger than the 20 with negative scans (31 +/- 12 v 42 +/- 17 years; P less than 0.01), and exhibited greater proteinuria (8.19 +/- 7.96 v 2.9 +/- 2.3 S/d; P less than 0.01) and lower serum creatinine values (2 +/- 2 v 4.1 +/- 2.8 mg/dL; P less than 0.01). The amount of proteinuria correlated directly with the intensity grade of the gallium image (P less than 0.02), but there was no correlation between the biopsy diagnosis and the outcome of the gallium scan. It was concluded that gallium scintigraphy is not useful in the differential diagnosis of the glomerular diseases under discussion. Younger patients with good renal function and heavy proteinuria are likely to have a positive renal scintigram regardless of the underlying glomerulopathy.

  16. Growth of doped silicon nanowires by pulsed laser deposition and their analysis by electron beam induced current imaging

    Energy Technology Data Exchange (ETDEWEB)

    Eisenhawer, B; Berger, A; Christiansen, S [Institute of Photonic Technology, Albert-Einstein-Strasse 9, 07745 Jena (Germany); Zhang, D; Clavel, R [Laboratory of Robotic Systems, Ecole Polytechnique Federale de Lausanne (EPFL), Station 9, CH-1015 Lausanne (Switzerland); Michler, J, E-mail: bjoern.eisenhawer@ipht-jena.de [Mechanics of Materials and Nanostructures Laboratory, EMPA-Materials Science and Technology, Feuerwerkstrasse 39, CH-3602 Thun (Switzerland)

    2011-02-18

    Doped silicon nanowires (NWs) were epitaxially grown on silicon substrates by pulsed laser deposition following a vapour-liquid-solid process, in which dopants together with silicon atoms were introduced into the gas phase by laser ablation of lightly and highly doped silicon target material. p-n or p{sup ++}-p junctions located at the NW-silicon substrate interfaces were thus realized. To detect these junctions and visualize them the electron beam induced current technique and two-point probe current-voltage measurements were used, based on nanoprobing individual silicon NWs in a scanning electron microscope. Successful silicon NW doping by pulsed laser deposition of doped target material could experimentally be demonstrated. This doping strategy compared to the commonly used doping from the gas phase during chemical vapour deposition is evaluated essentially with a view to potentially overcoming the limitations of chemical vapour deposition doping, which shows doping inhomogeneities between the top and bottom of the NW as well as between the core and shell of NWs and structural lattice defects, especially when high doping levels are envisaged. The pulsed laser deposition doping technique yields homogeneously doped NWs and the doping level can be controlled by the choice of the target material. As a further benefit, this doping procedure does not require the use of poisonous gases and may be applied to grow not only silicon NWs but also other kinds of doped semiconductor NWs, e.g. group III nitrides or arsenides.

  17. Data in support of Gallium (Ga3+) antibacterial activities to counteract E. coli and S. epidermidis biofilm formation onto pro-osteointegrative titanium surfaces

    Science.gov (United States)

    Cochis, A.; Azzimonti, B.; Sorrentino, R.; Della Valle, C.; De Giglio, E.; Bloise, N.; Visai, L.; Bruni, G.; Cometa, S.; Pezzoli, D.; Candiani, G.; Rimondini, L.; Chiesa, R.

    2016-01-01

    This paper contains original data supporting the antibacterial activities of Gallium (Ga3+)-doped pro-osteointegrative titanium alloys, obtained via Anodic Spark Deposition (ASD), as described in “The effect of silver or gallium doped titanium against the multidrug resistant Acinetobacter baumannii” (Cochis et al. 2016) [1]. In this article we included an indirect cytocompatibility evaluation towards Saos2 human osteoblasts and extended the microbial evaluation of the Ga3+ enriched titanium surfaces against the biofilm former Escherichia coli and Staphylococcus epidermidis strains. Cell viability was assayed by the Alamar Blue test, while bacterial viability was evaluated by the metabolic colorimetric 3-[4,5-dimethylthiazol-2-yl]-2,5 diphenyl tetrazolium bromide (MTT) assay. Finally biofilm morphology was analyzed by Scanning Electron Microscopy (SEM). Data regarding Ga3+ activity were compared to Silver. PMID:26909385

  18. Growth and Doping of Al(x)Ga(1-x)N Films by Electron Cyclotron Resonance Assisted Molecular Beam Epitaxy

    Science.gov (United States)

    1993-05-30

    In the case of a well- defined activation energy AEd, the FIG. 4. Temperature dependence of i,, n, and n. carrier concentration in the conduction band...this figure, the ". L Pankove, ModS Symp. Proc. 162, 515 (1990). vertical axis is a parameter S which is defined as the change 2P. .o and D. I. Ferry...Junctions and ence between the metal and GaN. The work function of ise aracas (Plenum New Y ork , e984). ""ha G. X Marcas , Gallium Arsenide Technology

  19. Applying bacterial metallophores to mobilize gallium

    Science.gov (United States)

    Schwabe, Ringo; Obst, Britta; Mehnert, Marika; Tischler, Dirk; Wiche, Oliver

    2017-04-01

    Metallophores are produced by many organisms such as bacteria, fungi and plants in order to mobilize metals, especially iron (Greek: "siderophore" = iron carrier), to overcome limitations or stress. Respectively, it is well known these compounds loaded with relevant metal ions are used not only by the producing organism but also by others. Thus metallophores as metal carriers are relevant for many processes at various habitats (e.g. metal acquisition, pathogenic factors, antimicrobial activity, sensing). However, metallophores do also mobilize metals of industrial interest which have no critical role in the living world. Here we focused on gallium as industrial relevant metal and compared it to iron which is important for all organisms. The herein described mobilization of valuable metals such as gallium from soils provides first hints towards alternative strategies, such as phytomining, sensor development, or solvent extraction based on metallophores. Two produced metallophore preparations of soil bacteria (Gordonia rubripertincta CWB2 and Paracoccus denitrificans PD1222) and the commercially available metallophore desferrioxamine B were analyzed for iron binding activity by means of a standard chromazurol S assay and equal iron binding activities were employed to treat a soil sample. The pH was set constant to 6 in order to avoid pH related effects. Therefore, the metallophore was prepared in a special medium and control of water and medium were also applied onto the soil. The soil was washed and incubated with the mentioned preparations. The mobilization of iron and gallium was determined prior and after the treatment by means of ICP-MS. Water showed no effect and medium only a little on metal mobilization which is related to its ionic strength. All metallophores mobilized iron at a similar strength but showed significant differences in case of gallium. Here the metallophore mix produced by strain CWB2 showed best results and allowed to mobilize gallium 3-times

  20. Myopericarditis in acquired immunodeficiency syndrome diagnosed by gallium scintigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Cregler, L.L.; Sosa, I.; Ducey, S.; Abbey, L. (Bronx VA Medical Center, NY (USA))

    1990-07-01

    Myocarditis is among the cardiac complications of acquired immunodeficiency syndrome and, yet, is often not discovered until autopsy. Gallium scintigraphy has been employed in diagnosing this entity, but few data are available about its diagnostic accuracy and value. Here, the authors report two cases of myopericarditis as diagnosed by gallium scan.

  1. Two octanuclear gallium metallamacrocycles of topologically different connectivities.

    Science.gov (United States)

    Park, Mira; John, Rohith P; Moon, Dohyun; Lee, Kyungjin; Kim, Ghyung Hwa; Lah, Myoung Soo

    2007-12-14

    Two topologically different metallamacrocycles--S8 symmetric octanuclear gallium(III) metalladiazamacrocycle and pseudo-D4 symmetric octanuclear gallium(III) metalladiazamacrocycle--could be prepared using two similar heteroditopic bridging ligands having asymmetrical tridentate-bidentate binding residues.

  2. Benchmarking of Evaluated Neutron Data for Gallium Sample

    Institute of Scientific and Technical Information of China (English)

    HAN; Rui; NIE; Yang-bo; RUAN; Xi-chao; BAO; Jie; REN; Jie; HUANG; Han-xiong; LI; Xia; ZHANG; Kai; ZHOU; Zu-ying

    2013-01-01

    Gallium(Ga)is a kind of target material and an important fission product.It has the characteristics of low melting point and high boiling point.The integral experimental study on Gallium data is an important issue.It has an important application for design of reactors and ADS(Accelerator Driven System)

  3. Design of Indium Arsenide nanowire sensors for pH and biological sensing and low temperature transport through p-doped Indium Arsenide nanowires

    DEFF Research Database (Denmark)

    Upadhyay, Shivendra

    With the goal of real time electrical detection of chemical and biological species, nanowires have shown great promise with high sensitivity due to their large surface to volume ratio. While the focus of such electrical detection has shifted to one dimensional semiconductor nanostuctures, Silicon...

  4. Magnetism and superconductivity in praseodymium-based filled skutterudite arsenides

    Science.gov (United States)

    Sayles, Todd Allen

    This work will cover studies on single crystals of PrRu4As 12 and PrFe4As12. It will begin by introducing the topic and the types of behavior and effects that can be expected to be found in materials. After this a brief discussion of sample growth and characterization will be given. Finally, work on the individual materials will be presented. It is found the various phases present in the antimonide Pr-based filled skutterudites continues with the arsenides as well. The first to be measured, PrOs4As12, proved just how interesting this topic would be. It displays two low temperature ordered states, the ground state of which is antiferromagnetically ordered. PrOs4As12 is also found to display single ion Kondo behavior from electrical resistivity and specific heat measurements. The electronic specific heat coefficient at zero temperature is found to decrease from a incredible value of ≈ 1 J/mol-K 2 in zero field to the still high values of several hundred mJ/mol-K 2 as the field is increased to 16 T. When the transition metal Os is replaced with Ru, PrRu4As 12, a BCS superconductor is discovered. Zero resistance is found below Tc = 2.4 K, and a Meissner state is found in magnetic susceptibility measurements at Tc = 2.4 K. In addition to the obvious phase transition at Tc = 2.4 K in specific heat, PrRu4As12 shows very conventional BCS properties in the specific heat measurements: DeltaC( Tc)/gammaTc = 1.53 and (perhaps more convincing) Ce has an exponential temperature dependence. For temperatures above Tc, a normal state electronic specific heat coefficient of 70 mJ/mol-K2 was found and, furthermore, crystalline electric field effects were present and studied. A Gamma1 singlet ground state was deduced, followed by a Gamma5 triplet first excited state. The final member of the family, PrFe4As12, was found to be a ferromagnet, with a possible low temperature spin reorientation. Magnetic susceptibility measurements find Curie-Weiss behavior above 80 K, and an onset to an

  5. Nuclear microprobe imaging of gallium nitrate in cancer cells

    Science.gov (United States)

    Ortega, Richard; Suda, Asami; Devès, Guillaume

    2003-09-01

    Gallium nitrate is used in clinical oncology as treatment for hypercalcemia and for cancer that has spread to the bone. Its mechanism of antitumor action has not been fully elucidated yet. The knowledge of the intracellular distribution of anticancer drugs is of particular interest in oncology to better understand their cellular pharmacology. In addition, most metal-based anticancer compounds interact with endogenous trace elements in cells, altering their metabolism. The purpose of this experiment was to examine, by use of nuclear microprobe analysis, the cellular distribution of gallium and endogenous trace elements within cancer cells exposed to gallium nitrate. In a majority of cellular analyses, gallium was found homogeneously distributed in cells following the distribution of carbon. In a smaller number of cells, however, gallium appeared concentrated together with P, Ca and Fe within round structures of about 2-5 μm diameter located in the perinuclear region. These intracellular structures are typical of lysosomial material.

  6. Computational Investigation of the Electronic and Optical Properties of Planar Ga-Doped Graphene

    Directory of Open Access Journals (Sweden)

    Nicole Creange

    2015-01-01

    Full Text Available We simulate the optical and electrical responses in gallium-doped graphene. Using density functional theory with a local density approximation, we simulate the electronic band structure and show the effects of impurity doping (0–3.91% in graphene on the electron density, refractive index, optical conductivity, and extinction coefficient for each doping percentage. Here, gallium atoms are placed randomly (using a 5-point average throughout a 128-atom sheet of graphene. These calculations demonstrate the effects of hole doping due to direct atomic substitution, where it is found that a disruption in the electronic structure and electron density for small doping levels is due to impurity scattering of the electrons. However, the system continues to produce metallic or semimetallic behavior with increasing doping levels. These calculations are compared to a purely theoretical 100% Ga sheet for comparison of conductivity. Furthermore, we examine the change in the electronic band structure, where the introduction of gallium electronic bands produces a shift in the electron bands and dissolves the characteristic Dirac cone within graphene, which leads to better electron mobility.

  7. Thermal Plasma Synthesis of Crystalline Gallium Nitride Nanopowder from Gallium Nitrate Hydrate and Melamine

    Directory of Open Access Journals (Sweden)

    Tae-Hee Kim

    2016-02-01

    Full Text Available Gallium nitride (GaN nanopowder used as a blue fluorescent material was synthesized by using a direct current (DC non-transferred arc plasma. Gallium nitrate hydrate (Ga(NO33∙xH2O was used as a raw material and NH3 gas was used as a nitridation source. Additionally, melamine (C3H6N6 powder was injected into the plasma flame to prevent the oxidation of gallium to gallium oxide (Ga2O3. Argon thermal plasma was applied to synthesize GaN nanopowder. The synthesized GaN nanopowder by thermal plasma has low crystallinity and purity. It was improved to relatively high crystallinity and purity by annealing. The crystallinity is enhanced by the thermal treatment and the purity was increased by the elimination of residual C3H6N6. The combined process of thermal plasma and annealing was appropriate for synthesizing crystalline GaN nanopowder. The annealing process after the plasma synthesis of GaN nanopowder eliminated residual contamination and enhanced the crystallinity of GaN nanopowder. As a result, crystalline GaN nanopowder which has an average particle size of 30 nm was synthesized by the combination of thermal plasma treatment and annealing.

  8. Electron tunneling transport across heterojunctions between europium sulfide and indium arsenide

    Science.gov (United States)

    Kallaher, Raymond L.

    This dissertation presents research done on utilizing the ferromagnetic semiconductor europium sulfide (EuS) to inject spin polarized electrons into the non-magnetic semiconductor indium arsenide (InAs). There is great interest in expanding the functionality of modern day electronic circuits by creating devices that depend not only on the flow of charge in the device, but also on the transport of spin through the device. Within this mindset, there is a concerted effort to establish an efficient means of injecting and detecting spin polarized electrons in a two dimensional electron system (2DES) as the first step in developing a spin based field effect transistor. Thus, the research presented in this thesis has focused on the feasibility of using EuS, in direct electrical contact with InAs, as a spin injecting electrode into an InAs 2DES. Doped EuS is a concentrated ferromagnetic semiconductor, whose conduction band undergoes a giant Zeeman splitting when the material becomes ferromagnetic. The concomitant difference in energy between the spin-up and spin-down energy bands makes the itinerant electrons in EuS highly spin polarized. Thus, in principle, EuS is a good candidate to be used as an injector of spin polarized electrons into non-magnetic materials. In addition, the ability to adjust the conductivity of EuS by varying the doping level in the material makes EuS particularly suited for injecting spins into non-magnetic semiconductors and 2DES. For this research, thin films of EuS have been grown via e-beam evaporation of EuS powder. This growth technique produces EuS films that are sulfur deficient; these sulfur vacancies act as intrinsic electron donors and the resulting EuS films behave like heavily doped ferromagnetic semiconductors. The growth parameters and deposition procedures were varied and optimized in order to fabricate films that have minimal crystalline defects. Various properties and characteristics of these EuS films were measured and compared to

  9. Contribution the scintigraphy with gallium 67 in the sarcoidosis; Apport de la scintigraphie au gallium 67 dans la sarcoidose

    Energy Technology Data Exchange (ETDEWEB)

    Elbez, I.; Sellem, A.; Rejeb, O.; Elkadri, N.; Hammami, H. [Service de medecine nucleaire, hopital militaire, Tunis, (Tunisia)

    2009-05-15

    The objective is to show the interest of the scintigraphy with citrates of gallium 67 in the diagnosis and follow up of sarcoidosis injuries. The conclusions are that the scintigraphy with gallium 67 constitutes an imaging technique of good performance, non invasive in the diagnosis, le injuries evaluation and the sarcoidosis follow-up. (N.C.)

  10. Patterned gallium surfaces as molecular mirrors.

    Science.gov (United States)

    Bossi, Alessandra; Rivetti, Claudio; Mangiarotti, Laura; Whitcombe, Michael J; Turner, Anthony P F; Piletsky, Sergey A

    2007-09-30

    An entirely new means of printing molecular information on a planar film, involving casting nanoscale impressions of the template protein molecules in molten gallium, is presented here for the first time. The metallic imprints not only replicate the shape and size of the proteins used as template. They also show specific binding for the template species. Such a simple approach to the creation of antibody-like properties in metallic mirrors can lead to applications in separations, microfluidic devices, and the development of new optical and electronic sensors, and will be of interest to chemists, materials scientists, analytical specialists, and electronic engineers.

  11. A hybrid density functional view of native vacancies in gallium nitride.

    Science.gov (United States)

    Gillen, Roland; Robertson, John

    2013-10-09

    We investigated the transition energy levels of the vacancy defects in gallium nitride by means of a hybrid density functional theory approach (DFT). We show that, in contrast to predictions from a recent study on the level of purely local DFT, the inclusion of screened exchange stabilizes the triply positive charge state of the nitrogen vacancy for Fermi energies close to the valence band. On the other hand, the defect levels associated with the negative charge states of the nitrogen vacancy hybridize with the conduction band and turn out to be energetically unfavorable, except for high n-doping. For the gallium vacancy, the increased magnetic splitting between up-spin and down-spin bands due to stronger exchange interactions in sX-LDA pushes the defect levels deeper into the band gap and significantly increases the associated charge transition levels. Based on these results, we propose the ϵ(0| - 1) transition level as an alternative candidate for the yellow luminescence in GaN.

  12. Sensor of hydrostatic pressure based on gallium antimonide microcrystals

    Directory of Open Access Journals (Sweden)

    Druzhinin A. A.

    2015-08-01

    Full Text Available Currently, silicon and germanium, the most common materials in the production of discrete semiconductor devices and integrated circuits, do not always meet all the requirements to the sensing elements of mechanical quantities sensors. Therefore, it is logical to research the properties of other semiconductor materials that could be used as sensing elements in such sensors. A3B5 semiconductor compounds seem promising for such purpose. Effect of hydrostatic pressure up to 5000 bar on the resistance of n-type antimonide gallium whiskers doped by Se or Te was studied. Coefficient of hydrostatic pressure for this crystals was determined, it equals Kh = (16,5—20,0•10–5 bar–1 at 20°N. Temperature dependence of resistance and coefficient Kh for this crystals in the temperature range ±60°N was studied. Design of the developed hydrostatic pressure sensor based on GaSb whiskers and its characteristics are presented. The possibility to decrease the temperature dependence of sensitive element resistance by mounting GaSb whiskers on the substrates fabricated from materials with different temperature coefficient of expansion was examined. It was shown that mounting of GaSb crystals on Cu substrate gives the optimal result, in this case the temperature coefficient decrease to 0,05%•°N–1, that leads to decrease of output temperature dependence. The main advantages of developed pressure sensor are: the simplified design in comparison with pressure sensors with strain gauges mounted on spring elements; the high sensitivity to pressure that is constant in the wide pressure range; the improvement of sensors metrological characteristics owing to hysteresis absence. The possible application fields of developed sensors are measuring of high and extremely high pressure, chemical and oil industries, measuring of pressure in oil bore-holes, investigation of explosive processes.

  13. Homoepitaxial growth of HVPE-GaN doped with Si

    Science.gov (United States)

    Iwinska, M.; Sochacki, T.; Amilusik, M.; Kempisty, P.; Lucznik, B.; Fijalkowski, M.; Litwin-Staszewska, E.; Smalc-Koziorowska, J.; Khapuridze, A.; Staszczak, G.; Grzegory, I.; Bockowski, M.

    2016-12-01

    Results of growth of high structural quality gallium nitride single crystals doped with silicon are described in this paper. Dichlorosilane was used as precursor of silicon in the hydride vapor phase epitaxy method. Crystallization runs with different flows of dichlorosilane were performed and compared. One-inch free-standing HVPE-GaN crystals of high structural quality and high purity, previously grown on ammonothermal GaN substrates, were used as seeds. Structural, electrical, and optical properties of HVPE-GaN doped with silicon are presented and discussed in detail. A laser diode built on the homoepitaxially grown GaN is demonstrated.

  14. Compatibility of ITER candidate structural materials with static gallium

    Energy Technology Data Exchange (ETDEWEB)

    Luebbers, P.R.; Michaud, W.F.; Chopra, O.K.

    1993-12-01

    Tests were conducted on the compatibility of gallium with candidate structural materials for the International Thermonuclear Experimental Reactor, e.g., Type 316 SS, Inconel 625, and Nb-5 Mo-1 Zr alloy, as well as Armco iron, Nickel 270, and pure chromium. Type 316 stainless steel is least resistant to corrosion in static gallium and Nb-5 Mo-1 Zr alloy is most resistant. At 400{degrees}C, corrosion rates are {approx}4.0, 0.5, and 0.03 mm/yr for type 316 SS, Inconel 625, and Nb-5 Mo- 1 Zr alloy, respectively. The pure metals react rapidly with gallium. In contrast to findings in earlier studies, pure iron shows greater corrosion than nickel. The corrosion rates at 400{degrees}C are {ge}88 and 18 mm/yr, respectively, for Armco iron and Nickel 270. The results indicate that at temperatures up to 400{degrees}C, corrosion occurs primarily by dissolution and is accompanied by formation of metal/gallium intermetallic compounds. The solubility data for pure metals and oxygen in gallium are reviewed. The physical, chemical, and radioactive properties of gallium are also presented. The supply and availability of gallium, as well as price predictions through the year 2020, are summarized.

  15. The effect of gallium nitrate on synoviocyte MMP activity.

    Science.gov (United States)

    Panagakos, F S; Kumar, E; Venescar, C; Guidon, P

    2000-02-01

    Gallium, a group IIIa metal salt, has been demonstrated to be an effective immunosuppressive agent. Gallium has also been shown to inhibit the production of inflammatory cytokines, such as IL-1beta, produced by macrophage-like cells in vitro. To further characterize the effects of gallium on the inflammatory process, we examined the effects of gallium nitrate on matrix metalloproteinase (MMP) activity utilizing the rabbit synoviocyte cell line HIG-82. HIG-82 cells were incubated with IL-1beta and TPA, with and without increasing concentrations of gallium nitrate. Conditioned medium was collected and assayed for MMP activity using a synthetic substrate and substrate gel zymography. IL-1beta and TPA alone induced MMP activity in HIG-82 cells. A dose-dependent inhibition of IL-1beta and TPA stimulated MMP activity by gallium nitrate at increasing concentrations was observed. This study demonstrates that gallium nitrate can inhibit the activity of MMPs and may be useful as a modulator of inflammation in arthritis.

  16. Gallium vacancies in β-Ga2O3 crystals

    Science.gov (United States)

    Kananen, B. E.; Halliburton, L. E.; Stevens, K. T.; Foundos, G. K.; Giles, N. C.

    2017-05-01

    The gallium vacancy, an intrinsic acceptor, is identified in β-Ga2O3 using electron paramagnetic resonance (EPR). Spectra from doubly ionized ( VG a 2 - ) and singly ionized ( VG a - ) gallium vacancies are observed at room temperature, without photoexcitation, after an irradiation with high-energy neutrons. The VG a 2 - centers (with S = 1/2) have a slight angular variation due to a small anisotropy in the g matrix (principal values are 2.0034, 2.0097, and 2.0322). The VG a 2 - centers also exhibit a resolved hyperfine structure due to equal and nearly isotropic interactions with the 69,71Ga nuclei at two Ga sites (the hyperfine parameters are 1.28 and 1.63 mT for the 69Ga and 71Ga nuclei, respectively, when the field is along the a direction). Based on these g-matrix and hyperfine results, the model for the ground state of the doubly ionized vacancy ( VG a 2 - ) has a hole localized on one threefold-coordinated oxygen ion. The vacancy is located at one of the three neighboring gallium sites, and the remaining two gallium neighbors are responsible for the equal hyperfine interactions. The singly ionized ( VG a - ) gallium vacancies are also paramagnetic. In this latter acceptor, the two holes are localized on separate oxygen ions adjacent to one gallium vacancy. Their spins align parallel to give a triplet S = 1 EPR spectrum with resolved hyperfine structure from interactions with gallium neighbors.

  17. A numerical simulation study of gallium-phosphide/silicon heterojunction passivated emitter and rear solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Hannes [Department of Solar Energy, Institute Solid-State Physics, Leibniz University of Hannover, Appelstr. 2, 30167 Hannover (Germany); ARC Photovoltaics Centre of Excellence, University of New South Wales (UNSW), Sydney, NSW 2052 (Australia); Ohrdes, Tobias [Institute for Solar Energy Research Hamelin (ISFH), 31860 Emmerthal (Germany); Dastgheib-Shirazi, Amir [Div. Photovoltaics, Department of Physics, University of Konstanz, 78457 Konstanz (Germany); Puthen-Veettil, Binesh; König, Dirk [ARC Photovoltaics Centre of Excellence, University of New South Wales (UNSW), Sydney, NSW 2052 (Australia); Altermatt, Pietro P. [Department of Solar Energy, Institute Solid-State Physics, Leibniz University of Hannover, Appelstr. 2, 30167 Hannover (Germany)

    2014-01-28

    The performance of passivated emitter and rear (PERC) solar cells made of p-type Si wafers is often limited by recombination in the phosphorus-doped emitter. To overcome this limitation, a realistic PERC solar cell is simulated, whereby the conventional phosphorus-doped emitter is replaced by a thin, crystalline gallium phosphide (GaP) layer. The resulting GaP/Si PERC cell is compared to Si PERC cells, which have (i) a standard POCl{sub 3} diffused emitter, (ii) a solid-state diffused emitter, or (iii) a high efficiency ion-implanted emitter. The maximum efficiencies for these realistic PERC cells are between 20.5% and 21.2% for the phosphorus-doped emitters (i)–(iii), and up to 21.6% for the GaP emitter. The major advantage of this GaP hetero-emitter is a significantly reduced recombination loss, resulting in a higher V{sub oc}. This is so because the high valence band offset between GaP and Si acts as a nearly ideal minority carrier blocker. This effect is comparable to amorphous Si. However, the GaP layer can be contacted with metal fingers like crystalline Si, so no conductive oxide is necessary. Compared to the conventional PERC structure, the GaP/Si PERC cell requires a lower Si base doping density, which reduces the impact of the boron-oxygen complexes. Despite the lower base doping, fewer rear local contacts are necessary. This is so because the GaP emitter shows reduced recombination, leading to a higher minority electron density in the base and, in turn, to a higher base conductivity.

  18. A numerical simulation study of gallium-phosphide/silicon heterojunction passivated emitter and rear solar cells

    Science.gov (United States)

    Wagner, Hannes; Ohrdes, Tobias; Dastgheib-Shirazi, Amir; Puthen-Veettil, Binesh; König, Dirk; Altermatt, Pietro P.

    2014-01-01

    The performance of passivated emitter and rear (PERC) solar cells made of p-type Si wafers is often limited by recombination in the phosphorus-doped emitter. To overcome this limitation, a realistic PERC solar cell is simulated, whereby the conventional phosphorus-doped emitter is replaced by a thin, crystalline gallium phosphide (GaP) layer. The resulting GaP/Si PERC cell is compared to Si PERC cells, which have (i) a standard POCl3 diffused emitter, (ii) a solid-state diffused emitter, or (iii) a high efficiency ion-implanted emitter. The maximum efficiencies for these realistic PERC cells are between 20.5% and 21.2% for the phosphorus-doped emitters (i)-(iii), and up to 21.6% for the GaP emitter. The major advantage of this GaP hetero-emitter is a significantly reduced recombination loss, resulting in a higher Voc. This is so because the high valence band offset between GaP and Si acts as a nearly ideal minority carrier blocker. This effect is comparable to amorphous Si. However, the GaP layer can be contacted with metal fingers like crystalline Si, so no conductive oxide is necessary. Compared to the conventional PERC structure, the GaP/Si PERC cell requires a lower Si base doping density, which reduces the impact of the boron-oxygen complexes. Despite the lower base doping, fewer rear local contacts are necessary. This is so because the GaP emitter shows reduced recombination, leading to a higher minority electron density in the base and, in turn, to a higher base conductivity.

  19. Niobium-gallium oxide with a high concentration of Cr3+ ions: Photoluminescence and structural characteristics

    Science.gov (United States)

    Costa, G. K. B.; Pedro, S. S.; López, A.; Carvalho, I. C. S.; Cella, N.; Sosman, L. P.

    2016-10-01

    This work presents photoluminescence data for gallium-niobium oxide with chromium ion as an impurity. The samples were obtained by the solid-state method (SSM) and the wet-chemical method (WCM) and investigated by X-ray diffraction, photoluminescence, excitation, and photoacoustic and X-ray fluorescence. The color of the sample obtained by the SSM was pink, while the color of the sample prepared by the WCM was green. This dramatic difference was associated with Cr3+ concentration and with the neighborhood of the doping ions, obtained from crystallographic data, which is strongly dependent on the preparation method. The difference between the samples was also verified in the photoacoustic and excitation spectra, in which the energy bands were located at different energy levels; on the other hand, in the photoluminescence spectra, no band shift was observed. All spectra were assigned to chromium ions at nonequivalent octahedral sites.

  20. Two-dimensional dopant profiling of gallium nitride p–n junctions by scanning capacitance microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Lamhamdi, M. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France); Ecole national des sciences appliquées khouribga, Université Hassan 1er, 26000 Settat (Morocco); Cayrel, F. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France); Frayssinet, E. [CRHEA-CNRS, Rue Bernard Grégory, Sophia Antipolis, 06560 Valbonne (France); Bazin, A.E.; Yvon, A.; Collard, E. [STMicroelectronics, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours (France); Cordier, Y. [CRHEA-CNRS, Rue Bernard Grégory, Sophia Antipolis, 06560 Valbonne (France); Alquier, D. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France)

    2016-04-01

    Two-dimensional imaging of dopant profiles for n and p-type regions are relevant for the development of new power semiconductors, especially for gallium nitride (GaN) for which classical profiling techniques are not adapted. This is a challenging task since it needs a technique with simultaneously good sensitivity, high spatial resolution and high dopant gradient resolution. To face these challenges, scanning capacitance microscopy combined with Atomic Force Microscopy is a good candidate, presenting reproducible results, as demonstrated in literature. In this work, we attempt to distinguish reliably and qualitatively the various doping concentrations and type at p–n and unipolar junctions. For both p–n and unipolar junctions three kinds of samples were prepared and measured separately. The space-charge region of the p–n metallurgical junction, giving rise to different contrasts under SCM imaging, is clearly observed, enlightening the interest of the SCM technique.

  1. Imaging the p-n junction in a gallium nitride nanowire with a scanning microwave microscope

    Energy Technology Data Exchange (ETDEWEB)

    Imtiaz, Atif [Physical Measurement Laboratory, National Institute of Standards and Technology, Boulder, Colorado 80305 (United States); Department of Electrical, Computer, and Energy Engineering, University of Colorado, Boulder, Colorado 80309 (United States); Wallis, Thomas M.; Brubaker, Matt D.; Blanchard, Paul T.; Bertness, Kris A.; Sanford, Norman A.; Kabos, Pavel, E-mail: kabos@boulder.nist.gov [Physical Measurement Laboratory, National Institute of Standards and Technology, Boulder, Colorado 80305 (United States); Weber, Joel C. [Physical Measurement Laboratory, National Institute of Standards and Technology, Boulder, Colorado 80305 (United States); Department of Mechanical Engineering, University of Colorado, Boulder, Colorado 80309 (United States); Coakley, Kevin J. [Information Technology Laboratory, National Institute of Standards and Technology, Boulder, Colorado 80305 (United States)

    2014-06-30

    We used a broadband, atomic-force-microscope-based, scanning microwave microscope (SMM) to probe the axial dependence of the charge depletion in a p-n junction within a gallium nitride nanowire (NW). SMM enables the visualization of the p-n junction location without the need to make patterned electrical contacts to the NW. Spatially resolved measurements of S{sub 11}{sup ′}, which is the derivative of the RF reflection coefficient S{sub 11} with respect to voltage, varied strongly when probing axially along the NW and across the p-n junction. The axial variation in S{sub 11}{sup ′}  effectively mapped the asymmetric depletion arising from the doping concentrations on either side of the junction. Furthermore, variation of the probe tip voltage altered the apparent extent of features associated with the p-n junction in S{sub 11}{sup ′} images.

  2. Carrier profiling in Si-implanted gallium nitride by Scanning Capacitance Microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Lamhamdi, M., E-mail: mohamed.lamhamdi@gmail.com [Universite Francois Rabelais de Tours, Laboratoire de Microelectronique de Puissance, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France); Cayrel, F. [Universite Francois Rabelais de Tours, Laboratoire de Microelectronique de Puissance, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France); Bazin, A.E. [Universite Francois Rabelais de Tours, Laboratoire de Microelectronique de Puissance, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France); STMicroelectronics, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France); Collard, E. [STMicroelectronics, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France); Alquier, D. [Universite Francois Rabelais de Tours, Laboratoire de Microelectronique de Puissance, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours Cedex 2 (France)

    2012-03-15

    To face silicon limits, gallium nitride (GaN) exhibits major interests for optoelectronics and power electronic devices. Nevertheless, several challenges have to be overcome, with local doping by ion implantation as a major one. It requires development of reliable characterization tools able to provide electrical information with nanoscale resolution. In this work, Atomic Force Microscopy (AFM) combined to its Scanning Capacitance Microscopy (SCM) mode was used for surface damages quantification and nanoscale dopant profiling. GaN samples have been implanted with Si in order to obtain a box-like profile and annealed above 1000 Degree-Sign C under nitrogen with AlN protective cap layer. SCM measurements have led to reliable and quantitative dopant electrical activity measurements thank to calibration sample. Moreover, a good agreement, in terms of depth and shape, has been obtained between SCM and SIMS profiles. This work has evidenced that a high activation rate of implanted Si can be achieved using rapid thermal annealing.

  3. Growth and characterization of indium antimonide and gallium antimonide crystals

    Indian Academy of Sciences (India)

    N K Udayashankar; H L Bhat

    2001-10-01

    Indium antimonide and gallium antimonide were synthesized from the respective component elements using an indigenously fabricated synthesis unit. Bulk crystals of indium antimonide and gallium antimonide were grown using both the vertical and horizontal Bridgman techniques. Effect of ampoule shapes and diameters on the crystallinity and homogeneity was studied. The grown crystals were characterized using X-ray analysis, EDAX, chemical etching, Hall effect and conductivity measurements. In the case of gallium antimonide, effect of dopants (Te and In) on transport and photoluminescence properties was investigated.

  4. Superconductivity in Co-doped SmFeAsO

    Energy Technology Data Exchange (ETDEWEB)

    Qi Yanpeng; Gao Zhaoshun; Wang Lei; Wang Dongliang; Zhang Xianping; Ma Yanwei [Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy of Sciences, PO Box 2703, Beijing 100190 (China)], E-mail: ywma@mail.iee.ac.cn

    2008-11-15

    Here we report the synthesis and characterizations of SmFe{sub 1-x}Co{sub x}AsO (x = 0.10, 0.15) for the first time. The parent compound SmFeAsO itself is not superconducting but shows an antiferromagnetic order near 150 K, which must be suppressed by doping before superconductivity emerges. With Co doping in the FeAs planes, antiferromagnetic order is destroyed and superconductivity occurs at 15.2 K. Similar to LaFe{sub 1-x}Co{sub x}AsO, the SmFe{sub 1-x}Co{sub x}AsO system appears to tolerate considerable disorder in the FeAs planes. This result is important, suggesting a different mechanism for cuprate superconductors compared to the iron-based arsenide ones.

  5. Growth of electronic materials in microgravity

    Science.gov (United States)

    Matthiesen, D. H.

    1991-01-01

    A growth experiment aimed at growing two selenium-doped gallium arsenide crystals, each of which are one inch in diameter and 3.45 inches in length, is described. Emphasis is placed on the effect of microgravity on the segregation behavior of electronic materials. The lessons learned from the 1975 ASTP mission have been incorporated in this experiment.

  6. Effect of oxidation on the Mechanical Properties of Liquid Gallium and Eutectic Gallium-Indium

    CERN Document Server

    Xu, Qin; Guo, Qiti; Jaeger, Heinrich; Brown, Eric

    2012-01-01

    Liquid metals exhibit remarkable mechanical properties, in particular large surface tension and low viscosity. However, these properties are greatly affected by oxidation when exposed to air. We measure the viscosity, surface tension, and contact angle of gallium (Ga) and a eutectic gallium-indium alloy (eGaIn) while controlling such oxidation by surrounding the metal with an acid bath of variable concentration. Rheometry measurements reveal a yield stress directly attributable to an oxide skin that obscures the intrinsic behavior of the liquid metals. We demonstrate how the intrinsic viscosity can be obtained with precision through a scaling technique that collapses low- and high-Reynolds number data. Measuring surface tension with a pendant drop method, we show that the oxide skin generates a surface stress that mimics surface tension and develop a simple model to relate this to the yield stress obtained from rheometry. We find that yield stress, surface tension, and contact angle all transition from solid-...

  7. Luminescence and Luminescence Quenching in Gd3(Ga,Al)5O12 Scintillators Doped with Ce3+

    NARCIS (Netherlands)

    Ogiegło, J.M.; Katelnikovas, A.; Zych, A.K.|info:eu-repo/dai/nl/31407564X; Jüstel, T.; Meijerink, A.|info:eu-repo/dai/nl/075044986; Ronda, R.C.

    2013-01-01

    The optical properties of gadolinium gallium aluminum garnet, Gd3(Ga,Al)5O12, doped with Ce3+ are investigated as a function of the Ga/Al ratio, aimed at an improved understanding of the energy flow and luminescence quenching in these materials. A decrease of both the crystal field strength and band

  8. Luminescence and Luminescence Quenching in Gd3(Ga,Al)5O12 Scintillators Doped with Ce3+

    NARCIS (Netherlands)

    Ogiegło, J.M.; Katelnikovas, A.; Zych, A.K.; Jüstel, T.; Meijerink, A.; Ronda, R.C.

    2013-01-01

    The optical properties of gadolinium gallium aluminum garnet, Gd3(Ga,Al)5O12, doped with Ce3+ are investigated as a function of the Ga/Al ratio, aimed at an improved understanding of the energy flow and luminescence quenching in these materials. A decrease of both the crystal field strength and band

  9. Recovery of gallium from coal fly ash by a dual reactive extraction process

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez, B.; Pazos, C.; Coca, J. [University of Oviedo, Oviedo (Spain). Dept. of Chemical Engineering and Environmental Technology

    1997-08-01

    This paper describes the extraction of gallium from coal fly ash by leaching and extraction with commercial extractants Amerlite LA-2 and LIX-54N dissolved in kerosene. Leaching of gallium and other metals from the fly ash was carried out with 6 M hydrochloric acid. The leaching liquor is first contacted with Amerlite LA-2 which extracts the gallium and iron. The iron is then precipitated with sodium hydroxide, while gallium remains in solution. Gallium is extracted selectively from the base solution with LIX 54; the resulting stripped solution contains 83% of the gallium present in the leaching liquor.

  10. Carbon doping of GaAs NWs

    Science.gov (United States)

    Salehzadeh Einabad, Omid

    Nanowires (NWs) have been proposed and demonstrated as the building blocks for nanoscale electronic and photonic devices such as NW field effect transistors and NW solar cells which rely on doping and trap-free carrier transport. Controlled doping of NWs and a high degree of structure and morphology control are required for device applications. However, doping of III-V nanowires such as GaAs nanowires has not been reported extensively in the literature. Carbon is a well known p-type dopant in planar GaAs due to its low diffusivity and high solubility in bulk GaAs; however its use as an intentional dopant in NW growth has not yet been investigated. In this work we studied the carbon doping of GaAs nanowires using CBr4 as the dopant source. Gold nanoparticles (NP) at the tip ofthe NWs have been used to drive the NW growth. We show that carbon doping suppresses the migration ofthe gold NPs from the tip of the NWs. In addition, we show that the carbon doping of GaAs NWs is accompanied by an increase of the axial growth rate and decrease of the lateral growth rate ofthe NWs. Carbon-doped GaAs NWs, unlike the undoped ones which are highly tapered, are rod-like. The origin of the observed morphological changes is attributed to the carbon adsorbates on the sidewalls ofthe nanowires which suppress the lateral growth of the nanowires and increase the diffusion length of the gallium adatoms on the sidewalls. Stacking fault formation consisting of alternating regIOns of zincblende and wurtzite structures has been commonly observed in NWs grown along the (111) direction. In this work, based on transmission electron microscopy (TEM) analysis, we show that carbon doping ofGaAs NWs eliminates the stacking fault formation. Raman spectroscopy was used to investigate the effects of carbon doping on the vibrational properties of the carbon-doped GaAs nanowires. Carbon doping shows a strong impact on the intrinsic longitudinal and transverse optical (La and TO) modes of the Ga

  11. Cathodoluminescence spectra of gallium nitride nanorods.

    Science.gov (United States)

    Tsai, Chia-Chang; Li, Guan-Hua; Lin, Yuan-Ting; Chang, Ching-Wen; Wadekar, Paritosh; Chen, Quark Yung-Sung; Rigutti, Lorenzo; Tchernycheva, Maria; Julien, François Henri; Tu, Li-Wei

    2011-12-14

    Gallium nitride [GaN] nanorods grown on a Si(111) substrate at 720°C via plasma-assisted molecular beam epitaxy were studied by field-emission electron microscopy and cathodoluminescence [CL]. The surface topography and optical properties of the GaN nanorod cluster and single GaN nanorod were measured and discussed. The defect-related CL spectra of GaN nanorods and their dependence on temperature were investigated. The CL spectra along the length of the individual GaN nanorod were also studied. The results reveal that the 3.2-eV peak comes from the structural defect at the interface between the GaN nanorod and Si substrate. The surface state emission of the single GaN nanorod is stronger as the diameter of the GaN nanorod becomes smaller due to an increased surface-to-volume ratio.

  12. Thickness dependent thermal conductivity of gallium nitride

    Science.gov (United States)

    Ziade, Elbara; Yang, Jia; Brummer, Gordie; Nothern, Denis; Moustakas, Theodore; Schmidt, Aaron J.

    2017-01-01

    As the size of gallium nitride (GaN) transistors is reduced in order to reach higher operating frequencies, heat dissipation becomes the critical bottleneck in device performance and longevity. Despite the importance of characterizing the physics governing the thermal transport in thin GaN films, the literature is far from conclusive. In this letter, we report measurements of thermal conductivity in a GaN film with thickness ranging from 15-1000 nm grown on 4H-SiC without a transition layer. Additionally, we measure the thermal conductivity in the GaN film when it is 1 μm-thick in the temperature range of 300 < T < 600 K and use a phonon transport model to explain the thermal conductivity in this film.

  13. Handling characteristics of gallium alloy for dental restoration.

    Science.gov (United States)

    Mash, L K; Miller, B H; Nakajima, H; Collard, S M; Guo, I Y; Okabe, T

    1993-12-01

    The handling characteristics of a gallium alloy (Gallium Alloy GF) were compared to those of a spherical high-copper amalgam (Tytin). Ten dentists each restored four identical MO preparations in acrylic typodont teeth (no. 30), two with amalgam and two with gallium alloy. Each restoration was evaluated immediately following completion by the operator for six clinically relevant criteria. Each criterion was scored between 1 and 5, where 1 = very poor, 2 = poor, 3 = fair, 4 = good, and 5 = very good. Three two-sided Mann-Whitney tests were used to compare the median scores for significant differences (P < 0.05). The first test indicated no significant difference between scores for the first- and second-placed restorations, within criteria and within alloy type (n = 10). The second test indicated a significant difference between amalgam and gallium alloy, within criteria and within restoration sequence (n = 10), for each criterion except resistance to fracture during removal of the matrix band. The third test indicated a significant difference between amalgam and gallium alloy, within each criteria, combining scores for first- and second-placed restorations (n = 20). During simulated clinical placement, amalgam was rated significantly higher than gallium alloy in each handling characteristic evaluated.

  14. Gallium Nitride Schottky betavoltaic nuclear batteries

    Energy Technology Data Exchange (ETDEWEB)

    Lu Min, E-mail: mlu2006@sinano.ac.c [Su zhou Institute of Nano-technology and Nano-bionics, CAS, Su zhou 215125 (China); Zhang Guoguang [China Institute of Atomic Energy, Beijing 102413 (China); Fu Kai; Yu Guohao [Su zhou Institute of Nano-technology and Nano-bionics, CAS, Su zhou 215125 (China); Su Dan; Hu Jifeng [China Institute of Atomic Energy, Beijing 102413 (China)

    2011-04-15

    Research highlights: {yields} Gallium Nitride nuclear batteries with Ni-63 are demonstrated for the first time. {yields} Open circuit voltage of 0.1 V and conversion efficiency of 0.32% have been obtained. {yields} The limited performance is due to thin effective energy deposition layer. {yields} The output power is expected to greatly increase with growing thick GaN films. -- Abstract: Gallium Nitride (GaN) Schottky betavoltaic nuclear batteries (GNBB) are demonstrated in our work for the first time. GaN films are grown on sapphire substrates by metalorganic chemical vapor deposition (MOCVD), and then GaN Schottky diodes are fabricated by normal micro-fabrication process. Nickel with mass number of 63 ({sup 63}Ni), which emits {beta} particles, is loaded on the GaN Schottky diodes to achieve GNBB. X-ray diffraction (XRD) and photoluminescence (PL) are carried out to investigate the crystal quality for the GaN films as grown. Current-voltage (I-V) characteristics shows that the GaN Schottky diodes are not jet broken down at -200 V due to consummate fabrication processes, and the open circuit voltage of the GNBB is 0.1 V and the short circuit current density is 1.2 nA cm{sup -2}. The limited performance of the GNBB is due to thin effective energy deposition layer, which is only 206 nm to absorb very small partial energy of the {beta} particles because of the relatively high dislocation density and carrier concentration. However, the conversion efficiency of 0.32% and charge collection efficiency (CCE) of 29% for the GNBB have been obtained. Therefore, the output power of the GNBB are expected to greatly increase with growing high quality thick GaN films.

  15. Electronic properties and chemical bonding in quaternary arsenide oxides LaZnAsO and YZnAsO

    Energy Technology Data Exchange (ETDEWEB)

    Bannikov, V.V.; Shein, I.R. [Institute of Solid State Chemistry, Ural Branch of the Russian Academy of Sciences, Pervomaiskaya, 91, 620041, Ekaterinburg (Russian Federation); Ivanovskii, A.L., E-mail: ivanovskii@ihim.uran.ru [Institute of Solid State Chemistry, Ural Branch of the Russian Academy of Sciences, Pervomaiskaya, 91, 620041, Ekaterinburg (Russian Federation)

    2009-07-15

    First principles FLAPW-GGA band structure calculations are employed to obtain the structural, electronic properties and chemical bonding picture for two related phases, namely, quaternary arsenide oxides LaZnAsO and YZnAsO. These compounds are found to be direct-transition type semiconductors with the GGA gaps of about 0.65-1.30 eV. The peculiarities of chemical bonding in these phases are investigated and discussed in comparison with quaternary arsenide oxide LaFeAsO-a basic phase for the newly discovered 26-55 K superconductors.

  16. Synergic phototoxic effect of visible light or Gallium-Arsenide laser in the presence of different photo-sensitizers on Porphyromonas gingivalis and Fusobacterium nucleatum

    Directory of Open Access Journals (Sweden)

    Habibollah Ghanbari

    2015-01-01

    Conclusion: Within the limitations of this study, the synergic phototoxic effect of visible light in combination with each of the photosensitizers on P. gingivalis and F. nucleatum. However, the synergic phototoxic effect of laser exposure and hydrogen peroxide and curcumin as photosensitizers on F. nucleatum was not shown.

  17. Electronic Properties of III-V Semiconductors under [111] Uniaxial Strain; a Tight-Binding Approach: I. Arsenides and Gallium Phosphide

    Directory of Open Access Journals (Sweden)

    Miguel E. Mora-Ramos

    2009-01-01

    Full Text Available Empleando un esquema de cálculo tight-binding que usa una base de orbitales sp3s*d5, se estudian propiedades de la estructura electrónica de un grupo de materiales semiconductores IIIV los cuales son de notable interés para la tecnología de dispositivos electrónicos y optoelectrónicos. En específico, se analiza la influencia sobre estas propiedades de una tensión aplicada según la dirección cristalográfica [111], haciendo uso de una formulación basada en la teoría de la elasticidad para establecer las posiciones relativas de los iones vecinos más próximos. Especial atención se presta a la inclusión del efecto de deformación interna de la red cristalina. Para cada material de los estudiados presentamos las dependencias de las brechas energéticas asociadas a los puntos L, X y L de la zona de Brillouin como funciones de la tensión uniaxial en AlAs, GaAs, InAs y GaP. Asimismo, reportamos expresiones de ajuste para los valores de las masas efectivas de conducción en esos cuatro materiales. La comparación de la variación de la brecha de energía en X para el GaP, calculada con nuestro modelo, y recientes resultados experimentales para la transición indirecta entre la banda de huecos pesados y la banda X de conducción arroja una muy buena concordancia.

  18. Materials Integration and Metamorphic Substrate Engineering from Silicon to Gallium Arsenide to Indium Phosphide for Advanced III-V/Silicon Photovoltaics

    Science.gov (United States)

    Carlin, Andrew M.

    Lattice-mismatched epitaxy in the III-V compound semiconductor system based on III-AsP and related alloys are of enormous importance, and considerable research interest, for many years. The reason is straightforward if one considers the limitations placed on available materials properties for devices dictated by lattice matching to the dominant substrate technologies - Si, GaAs (and/or Ge) and InP. For III-V epitaxy, the lattice constants of these substrates have defined a generation or more of device advances since growth of heterostructures possessing the same equilibrium lattice constants as the substrate yields essentially defect-free (specifically extended defect-free) materials and devices. Removing the restriction of lattice matching to current substrate technology opens a rich spectrum of bandgaps, bandgap combinations, conduction and valence band offsets, etc., that are desirable and exploitable for advancing device technologies for new functionality and greater performance. However successful exploitation of these properties requires mitigation of a variety of extended defects that result from the lattice mismatch between substrate and epitaxial heterostructures. A well known method to achieve this solution is through the use of compositionally (lattice constant-graded) buffer interlayers, in which the equilibrium lattice constants of interlayers are slowly altered by controlled changes in layer composition so that the mismatch strain between the initial substrate and the final device layers is spread across a thickness of buffer. The research accomplished has yielded success for both lattice constant ranges Si - GaAs and GaAs - InP. For the Si - GaAs system, a three step GaP nucleation process on Si has been developed and demonstrated, which maintains total avoidance of creating coalescence-related defects such as antiphase domains and stacking faults resulting from the initial III-V/IV interfaces while reducing overall threading dislocation density by ~10x, to a range of 1×107 cm-2, compared to current state of the art. This reduction can now enable future III-V/Si solar cells based on GaAsP metamorphic buffers in which the underlying Si substrate can participate as an active sub-cell, and such buffers have been demonstrated in this research. Second, in this same lattice constant range, novel GaP/SiGe interfaces on Si were grown and demonstrated to eliminate the small, but not negligible lattice misfit between GaP and Si, and provides a second pathway for future III-V/Si solar cell integration through subsequent metamorphic buffer growth. For the GaAs-InP range of lattice constants, multiple metamorphic buffer strategies, including those based on anion-specific quaternary GaInAsP, combinations of step and linearly-graded buffers, and buffers with multiple ternary alloys were all investigated. Micro-scale phase separation within quaternary anion-graded GaInAsP was identified as a mechanism to significantly inhibit proper lattice misfit strain relaxation, which was explained by thermodynamic arguments consistent with theoretical phase separation. This led to the creation of hybrid step and linearly graded InGaAs/InGaP metamorphic buffers through which phase separation was totally eliminated by avoiding specific compositions that were identified as sources for phase separation. These findings have enabled a realistic path for accessing the full range of bandgaps needed for future high efficiency III-V solar cells through optimized metamorphic III-V grading strategies.

  19. Time-resolved characterization of InAs/InGaAs quantum dot gain material for 1.3 µm lasers on gallium arsenide

    DEFF Research Database (Denmark)

    Fiore, Andrea; Borri, Paola; Langbein, Wolfgang

    2000-01-01

    The time-resolved optical characterization of InAs/InGaAs quantum dots emitting at 1.3 ìm is presented. A photoluminescence decay time of 1.8 ns and a fast rise time of 10ps are measured close to room temperature.......The time-resolved optical characterization of InAs/InGaAs quantum dots emitting at 1.3 ìm is presented. A photoluminescence decay time of 1.8 ns and a fast rise time of 10ps are measured close to room temperature....

  20. Effect of Heat Treatment on Electrical Properties and Charge Collection Efficiency of X-Ray Sensors Based on Chrome-Compensated Gallium Arsenide

    Science.gov (United States)

    Zarubin, A. N.; Kolesnikova, I. I.; Lozinskaya, A. D.; Novikov, V. A.; Skakunov, M. S.; Tolbanov, O. P.; Tyazhev, A. V.; Shemeryankina, A. V.

    2016-06-01

    We present the results of experimental studies of the dependences of the specific resistance, charge collection efficiency, product of the mobility on the lifetime (μ×τ)n, and current-voltage characteristics on the heat treatment regimes of X-ray Me-GaAs:Cr-Me-sensors. Experimental samples were the pad-sensors with the area of 0.1-0.25 cm2 and sensitive-layer thickness in the range of 400-500 μm. The values of (μ×τ)n were evaluated by measuring the dependence of the charge collection efficiency on the bias voltage when exposed to gamma rays from the source of 241Am. It is shown that heat treatment in the temperature range 200-500°C does not lead to a significant degradation of properties of Me-GaAs:Cr-Me-sensors and can be used in the manufacturing technology of matrix detectors of ionizing radiation.

  1. Drug-induced gingival enlargement: biofilm control and surgical therapy with gallium-aluminum-arsenide (GaAlAs) diode laser-A 2-year follow-up.

    Science.gov (United States)

    de Oliveira Guaré, Renata; Costa, Soraya Carvalho; Baeder, Fernando; de Souza Merli, Luiz Antonio; Dos Santos, Maria Teresa Botti Rodrigues

    2010-01-01

    Drug-induced gingival enlargement has been reported in patients treated with various types of anticonvulsant drugs, and is generally associated with the presence of plaque, gingival inflammation, and a genetic predisposition. Effective treatment includes daily oral hygiene and periodic professional prophylaxis. However, in some patients, surgical removal of the gingival tissue overgrowth becomes necessary. The patient in this case report was mentally impaired and had severe drug-induced gingival enlargement. This report describes the initial protocol, the gingivectomy, and a 2-year follow-up. A diode laser was used as an effective and safe method to remove the patient's overgrown gingival tissue.

  2. Estimation of various scattering parameters and 2-DEG mobilities from electron mobility calculations in the three conduction bands , L and X of gallium arsenide

    Indian Academy of Sciences (India)

    Sonal Singhal; A K Saxena; S Dasgupta

    2007-10-01

    The electron drift mobility in conduction band of GaAs has been calculated before, but for the first time, we have made attempts to estimate the electron mobilities in higher energy L and X minima. We have also calculated the value of mobility of two-dimensional electron gas needed to predict hetero-structure device characteristics using GaAs. Best scattering parameters have been derived by close comparison between experimental and theoretical mobilities. Room temperature electron mobilities in , L and X valleys are found to be nearly 9094, 945 and 247 cm2 /V-s respectively. For the above valleys, the electron masses, deformation potentials and polar phonon temperatures have been determined to be (0.067, 0.22, 0.39m 0 ), (8.5, 9.5, 6.5 eV), and (416, 382, 542 K) as best values, respectively. The 2-DEG electron mobility in minimum increases to 1.54 × 106 from 1.59 × 105 cm2 /V-s (for impurity concentration of 1014 cm-3) at 10 K. Similarly, the 2-DEG electron mobility values in L and X minima are estimated to be 2.28 × 105 and 1.44 × 105 cm2 /V-s at 10 K, which are about ∼ 4.5 and ∼ 3.9 times higher than normal value with impurity scattering present.

  3. Measurement and comparison of AC parameters of silicon (BSR and BSFR) and gallium arsenide (GaAs/Ge) solar cells used in space applications

    Energy Technology Data Exchange (ETDEWEB)

    Anil Kumar, R.; Suresh, M.S. [ISRO Satellite Centre, ISRO, Bangalore 560, 017 Kolhapur (India); Nagaraju, J. [Department of Instrumentation, Indian Institute of Science, Bangalore 560, 012 Kolhapur (India)

    2000-01-15

    The AC parameters of silicon (BSR and BSFR) solar cells and GaAs/Ge solar cell have been measured using impedance spectroscopy. Each cell capacitance, dynamic resistance and series resistance were measured and compared. GaAs/Ge solar cell has shown only the transition capacitance throughout its operating range while silicon (BSR and BSFR) solar cells exhibited both transition and diffusion capacitance. The theoretical and experimental values of dynamic resistance were compared and found in good agreement while the diode factor in silicon solar cells varies from 2 to 1, where as in GaAs/Ge solar cell it varies from 4 to 2 to 1.

  4. Capacitance-voltage studies of atomic-layer-deposited MOS structrures on Gallium Arsenide and other III-V compound semiconductors

    OpenAIRE

    Yang, Tian

    2007-01-01

    Si-based CMOS devices with traditional structure are approaching the fundamental physical limits. New device structures and materials must be explored to continue the trend of increasing electronic device speed and decreasing size at the same time. Recently, III-V compound semiconductors are considered as novel channel materials to replace Si due to their high electron mobilities. However, the main obstacle to implement III-V as novel channel materials for CMOS application is the lack of high...

  5. A Novel Approach to Modeling the Effects of Radiation in Gallium-Arsenide Solar Cells Using Silvaco’s ATLAS Software

    Science.gov (United States)

    2004-09-01

    Substrate subTH=200; subDop=5e17; % Depletion Layer Vo=k*T*log(Bdop*Edop/((ni)^2))/e; WDep =((2*epsR*epso*Vo*(Bdop+Edop))/(e*Bdop*Edop))^.5*10^6...BDepTH= WDep /(1+Bdop/Edop); EDepTH= WDep /(1+Edop/Bdop); %Standard number of Divisions divs=8; % Cell Structure calculations ### %\\Cell is

  6. Thin films of gallium arsenide on low-cost substrates. Quarterly technical progress report No. 8 and topical report No. 3, April 2-July 1, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, R.P.; Dapkus, P.D.; Dupuis, R.D.; Johnson, R.E.; Manasevit, H.M.; Moudy, L.A.; Yang, J.J.; Yingling, R.D.

    1978-07-01

    The seventh quarter of work on the contract is summarized. The metalorganic chemical vapor deposition (MO-CVD) technique has been applied to the growth of thin films of GaAs and GaAlAs on inexpensive polycrystalline or amorphous substrate materials (primarily glasses and metals) for use in fabrication of large-area low-cost photovoltaic device structures. Trimethylgallium (TMG), arsine (AsH/sub 3/), and trimethylaluminum (TMAl) are mixed in appropriate concentrations at room temperature in the gaseous state and pyrolyzed at the substrate, which is heated in a vertical reactor chamber to temperatures of 725 to 750/sup 0/C, to produce the desired film composition and properties. The technical activities during the quarter were concentrated on (1) a continuing evaluation of various graphite materials as possible substrates for MO-CVD growith of the polycrystalline GaAs solar cells; (2) attempts to improve the quality (especially the grain size) of polycrystalline GaAs films on Mo sheet and Mo/glass substrates by using HCl vapor during the MO-CVD growith process; (3) further studies of the transport properties of polycrystalline GaAs films, wth emphasis on n-type films; (4) continuing investigations of the properties of p-n junctions in polycrystalline GaAs, with emphasis on the formation and properties of p/sup +//n/n/sup +/ deposited structures; and (5) assembling apparatus and establishing a suitable technique for producing TiO/sub 2/ layers for use as AR coatings on GaAs cells. Progress is reported. (WHK)

  7. Functional renormalization group study of an 8-band model for the iron arsenides

    Science.gov (United States)

    Honerkamp, Carsten; Lichtenstein, Julian; Maier, Stefan A.; Platt, Christian; Thomale, Ronny; Andersen, Ole Krogh; Boeri, Lilia

    2014-03-01

    We investigate the superconducting pairing instabilities of eight-band models for 1111 iron arsenides. Using a functional renormalization group treatment, we determine how the critical energy scale for superconductivity depends on the electronic band structure. Most importantly, if we vary the parameters from values corresponding to LaFeAsO to SmFeAsO, the pairing scale is strongly enhanced, in accordance with the experimental observation. We analyze the reasons for this trend and compare the results of the eight-band approach to those found using five-band models.

  8. Functional renormalization group study of an eight-band model for the iron arsenides

    Science.gov (United States)

    Lichtenstein, J.; Maier, S. A.; Honerkamp, C.; Platt, C.; Thomale, R.; Andersen, O. K.; Boeri, L.

    2014-06-01

    We investigate the superconducting pairing instabilities of eight-band models for the iron arsenides. Using a functional renormalization group treatment, we determine how the critical energy scale for superconductivity depends on the electronic band structure. Most importantly, if we vary the parameters from values corresponding to LaFeAsO to SmFeAsO, the pairing scale is strongly enhanced, in accordance with the experimental observation. We analyze the reasons for this trend and compare the results of the eight-band approach to those found using five-band models.

  9. Indium arsenide nanowire field-effect transistors for pH and biological sensing

    Energy Technology Data Exchange (ETDEWEB)

    Upadhyay, S.; Krogstrup, P.; Nygård, J., E-mail: nygard@nbi.dk [Center for Quantum Devices and Nanoscience Center, Niels Bohr Institute, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark); Frederiksen, R.; Lloret, N.; Martinez, K. L. [Bio-Nanotechnology and Nanomedicine Laboratory, Department of Chemistry and Nanoscience Center, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark); De Vico, L.; Jensen, J. H. [Department of Chemistry, University of Copenhagen, Universitetsparken 5, DK-2100 Copenhagen (Denmark)

    2014-05-19

    Indium Arsenide is a high mobility semiconductor with a surface electron accumulation layer that allows ohmic electrical contact to metals. Here, we present nanowire devices based on this material as a platform for chemical and biological sensing. The sensing principle involves the binding of a charged species at the sensor surface transduced via field effect into a change in current flowing through the sensor. We show the sensitivity of the platform to the H{sup +} ion concentration in solution as proof of principle and demonstrate the sensitivity to larger charged protein species. The sensors are highly reproducible and reach a detection limit of 10 pM for Avidin.

  10. High Pressure X-ray Diffraction Study on Icosahedral Boron Arsenide (B12As2)

    Energy Technology Data Exchange (ETDEWEB)

    J Wu; H Zhu; D Hou; C Ji; C Whiteley; J Edgar; Y Ma

    2011-12-31

    The high pressure properties of icosahedral boron arsenide (B12As2) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B12As2 retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B12As2-c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.

  11. Role of Gallium and labeled leukocyte scintigraphy in AIDS patient

    Energy Technology Data Exchange (ETDEWEB)

    Palestro, C.J. [Division of nuclear medicine, Long Island Jewish Medical Center, New Hyde Park, New York (United States); Goldsmith, S.J. [Division of nuclear medicine, New York Hospital, Cornell Medical Center, New York (United States)

    1995-09-01

    Because AIDS patients frequently present with minimal symptomatology, radionuclide imaging with its ability to survey the entire body, is especially valuable. Gallium-67 citrate, the most commonly performed radionuclide study for localizing infection in these patients, is most useful for detecting opportunistic infections, especially in the thorax. A negative gallium scan, particularly when the chest X-ray is unremarkable, rules strongly against pulmonary disease. A negative gallium scan in a patient with an abnormal chest X-ray and Kaposi`s sarcoma, suggests that the patient`s respiratory distress is related to the neoplasm. Diffuse pulmonary parenchymal uptake of gallium in the HIV (+) patient is most often associated with PCP. While there are other causes of diffuse pulmonary uptake, the more intense or heterogeneous the uptake, the more likely the patient is to have PCP. Focal pulmonary uptake is usually associated with bacterial pneumonia although PCP may occasionally present in this fashion. Lymph node uptake of gallium is usually associated with Mycob acterium avium complex, tuberculosis, or Iymphoma. When corresponding abnormalities are present on thallium scintigraphy lymphoma is likely. Gallium positive, thallium negative, studies suggest mycobacterial disease. Labeled leukocyte imaging is not useful for detecting opportunistic infections probably because of the inflammatory response incited by these organisms. Leukocyte imaging is, however, more sensitive for detecting bacterial pneumonia. In the abdomen, gallium imaging is most useful for identifying lymphadenopathy, while labeled leukocyte imaging is superior for detecting AlDS-associated colitides. In summary, radionuclide studies are valuable diagnostic modalities in AIDS. Their success can be maximized by tailoring the study to the individual`s needs.

  12. Application of ultrasound in solvent extraction of nickel and gallium

    Energy Technology Data Exchange (ETDEWEB)

    Pesic, B.

    1996-07-01

    The effects of ultrasound on the rate of solvent extraction of nickel with Lix 65N and Lix 70, and gallium with Kelex 100 were investigated. These solvent extraction systems are noted by their sluggish nature. Low frequency (20 kHz) ultrasound increased the rates of extraction of nickel by factors of four to seven. The ultrasound had no effect on the final chemical equilibrium. Gallium extraction rates were enhanced with the use of ultrasound by as much as a factor of 15. Again, the ultrasound had no effect on extraction equilibrium. For both nickel and gallium, the enhanced rates were attributed to increased interfacial surface area associated with ultrasonically induced cavitation and microdroplet formation. The stability of the microdroplets permitted intermittent application of ultrasound with corresponding decreases in ultrasonic energy requirements. The lowest energy consumption was observed with short (0.25 to 5 s) bursts of high power (41 to 61 W) ultrasonic inputs. The study also provided insight into the factors that affect the complex extraction of gallium from sodium aluminate solutions. The rate controlling step was found to be the dehydration of the gallate ion, Ga(OH)4, and the first complex formation between gallium and Kelex 100. Sodium was found to enhance the extraction rate up to a point, beyond which increased concentration was detrimental. Increasing aluminum concentration was found to slow extraction rates. Modifiers and diluents were shown to markedly affect extraction rates even without ultrasound. Ketone modifiers, particularly 2-undecanone, when used with Kermac 470B or Escaid 200 diluents enhanced extraction rates of gallium to the point that the use of ultrasound provided no additional benefits. The positive effects of ketone modifiers for the solvent extraction of gallium had not been previously reported.

  13. Ab Initio study of the diffusion mechanisms of gallium in a silicon matrix

    Science.gov (United States)

    Levasseur-Smith, K.; Mousseau, N.

    2008-07-01

    We present the results of a study into the diffusion mechanisms of Ga defects in crystalline Si using ab initio techniques. Five stable neutral configurations for single and multi-atom defects are identified by density-functional theory (DFT) calculations within the local density approximation and using a localized basis set as implemented in the SIESTA package. Formation energy (E_F) calculations on these stable structures show the most likely neutral single-atom defect to be the Ga substitutional, with an EF of 0.7 eV in good agreement with previous work. Charge state studies show the Ga tetrahedral interstitial defect to be in a +1 state for most doping conditions. They also indicate the possibility for a gallium substitutional-tetrahedral interstitial complex to act as a deactivating center for the Ga dopants except in n-doped regime, where the complex adopts a -1 charge state. Migration pathway calculations using SIESTA coupled with the activation relaxation technique (ART nouveau) allow us to determine possible migration paths from the stable configurations found, under various charge states. In general, diffusion barriers decrease as the charge state becomes more negative, suggesting that the presence of Si self-interstitials can enhance diffusion through the kicking out of substitutional Si and by adding negative charge carriers to the system. An overall picture of a possible Ga diffusion and complex formation mechanism is presented based on these results.

  14. Gallium a unique anti-resorptive agent in bone: Preclinical studies on its mechanisms of action

    Energy Technology Data Exchange (ETDEWEB)

    Bockman, R.; Adelman, R.; Donnelly, R.; Brody, L.; Warrell, R. (Hospital for Special Surgery, New York, NY (USA)); Jones, K.W. (Brookhaven National Lab., Upton, NY (USA))

    1990-01-01

    The discovery of gallium as a new and unique agent for the treatment of metabolic bone disorders was in part fortuitous. Gallium is an exciting new therapeutic agent for the treatment of pathologic states characterized by accelerated bone resorption. Compared to other therapeutic metal compounds containing platinum or germanium, gallium affects its antiresorptive action without any evidence of a cytotoxic effect on bone cells. Gallium is unique amongst all therapeutically available antiresorptive agents in that it favors bone formation. 18 refs., 1 fig.

  15. Gallium based low-interaction anions

    Science.gov (United States)

    King, Wayne A.; Kubas, Gregory J.

    2000-01-01

    The present invention provides: a composition of the formula M.sup.+x (Ga(Y).sub.4.sup.-).sub.x where M is a metal selected from the group consisting of lithium, sodium, potassium, cesium, calcium, strontium, thallium, and silver, x is an integer selected from the group consisting of 1 or 2, each Y is a ligand selected from the group consisting of aryl, alkyl, hydride and halide with the proviso that at least one Y is a ligand selected from the group consisting of aryl, alkyl and halide; a composition of the formula (R).sub.x Q.sup.+ Ga(Y).sub.4.sup.- where Q is selected from the group consisting of carbon, nitrogen, sulfur, phosphorus and oxygen, each R is a ligand selected from the group consisting of alkyl, aryl, and hydrogen, x is an integer selected from the group consisting of 3 and 4 depending upon Q, and each Y is a ligand selected from the group consisting of aryl, alkyl, hydride and halide with the proviso that at least one Y is a ligand selected from the group consisting of aryl, alkyl and halide; an ionic polymerization catalyst composition including an active cationic portion and a gallium based weakly coordinating anion; and bridged anion species of the formula M.sup.+x.sub.y [X(Ga(Y.sub.3).sub.z ].sup.-y.sub.x where M is a metal selected from the group consisting of lithium, sodium, potassium, magnesium, cesium, calcium, strontium, thallium, and silver, x is an integer selected from the group consisting of 1 or 2, X is a bridging group between two gallium atoms, y is an integer selected from the group consisting 1 and 2, z is an integer of at least 2, each Y is a ligand selected from the group consisting of aryl, alkyl, hydride and halide with the proviso that at least one Y is a ligand selected from the group consisting of aryl, alkyl and halide.

  16. Gallium nitrate inhibits alkaline phosphatase activity in a differentiating mesenchymal cell culture.

    Science.gov (United States)

    Boskey, A L; Ziecheck, W; Guidon, P; Doty, S B

    1993-02-01

    The effect of gallium nitrate on alkaline phosphatase activity in a differentiating chick limb-bud mesenchymal cell culture was monitored in order to gain insight into the observation that rachitic rats treated with gallium nitrate failed to show the expected increase in serum alkaline phosphatase activity. Cultures maintained in media containing 15 microM gallium nitrate showed drastically decreased alkaline phosphatase activities in the absence of significant alterations in total protein synthesis and DNA content. However, addition of 15 microM gallium nitrate to cultures 18 h before assay for alkaline phosphatase activity had little effect. At the light microscopic and electron microscopic level, gallium-treated cultures differed morphologically from gallium-free cultures: with gallium present, there were fewer hypertrophic chondrocytes and cartilage nodules were flatter and further apart. Because of altered morphology, staining with an antibody against chick cartilage alkaline phosphatase appeared less extensive; however, all nodules stained equivalently relative to gallium-free controls. Histochemical staining for alkaline phosphatase activity was negative in gallium-treated cultures, demonstrating that the alkaline phosphatase protein present was not active. The defective alkaline phosphatase activity in cultures maintained in the presence of gallium was also evidenced when cultures were supplemented with the alkaline phosphatase substrate, beta-glycerophosphate (beta GP). The data presented suggest that gallium inhibits alkaline phosphatase activity in this culture system and that gallium causes alterations in the differentiation of mesenchymal cells into hypertrophic chondrocytes.

  17. Imaging Gallium Nitride High Electron Mobility Transistors to Identify Point Defects

    Science.gov (United States)

    2014-03-01

    REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE IMAGING GALLIUM NITRIDE HIGH ELECTRON MOBILITY TRANSISTORS TO IDENTIFY...Identification of these trends will assist in the improvement of gallium nitride HEMT fabrication processes leading to the development of more...reliable devices. 14. SUBJECT TERMS Electron microscopy, Gallium Nitride (GaN), high electron mobility transistor (HEMT

  18. Gallium scintigraphy in a case of septic cavernous sinus thrombosis

    Energy Technology Data Exchange (ETDEWEB)

    Palestro, C.J.; Malat, J.; Gladstone, A.G.; Richman, A.H.

    1986-09-01

    Septic cavernous sinus thrombosis, a relatively uncommon disease entity, frequently can be fatal. Early diagnosis is imperative in order that appropriate treatment be instituted. A 59-year-old woman who was admitted to our institution with complaints of diplopia, blurred vision and fevers that developed following a tooth extraction is presented. Initial CT and lumbar puncture on the day of admission were totally normal. A repeat CT performed 48 hours after admission, on the same day as gallium imaging, demonstrated findings consistent with cavernous sinus thrombosis. Gallium imaging demonstrated intense uptake in the left cavernous sinus and left orbit as well as moderately increased activity in the right cavernous sinus and orbit, confirming infection. The patient was treated with antibiotics, and repeat CT and gallium imaging were performed ten days later, both of which demonstrated near total resolution of the disease process. Conceivably, if gallium imaging had been initiated on the day of admission it may have been the first study to demonstrate an infectious process in the cavernous sinus. Gallium imaging should be considered as a diagnostic tool in the noninvasive workup of this entity.

  19. Electronic Structures of Silicene Doped with Galium: First Principle study

    Directory of Open Access Journals (Sweden)

    Pamungkas Mauludi Ariesto

    2015-01-01

    Full Text Available Following the success of graphene which possesses unique and superior properties, 2D material other than graphene become centre of interest of material scientists.Silicene, which has the same crystal structure as graphene but consist of silicon atoms rather than carbon become intriguing material due to domination of silicon as main material of electronic component. It is common to enhance electronic properties of semiconductor by adding dopant atoms. The electronic properties of Silicene doped with Gallium are investigated using first principle calculation based on density functional theory (DFT.Ga doping changes character of silicene from semimetal to conductor except silicene with Ga doping on S-site (Ga atom substitutes one Si atom which lead to semiconductor.

  20. Gallium nitride based logpile photonic crystals.

    Science.gov (United States)

    Subramania, Ganapathi; Li, Qiming; Lee, Yun-Ju; Figiel, Jeffrey J; Wang, George T; Fischer, Arthur J

    2011-11-09

    We demonstrate a nine-layer logpile three-dimensional photonic crystal (3DPC) composed of single crystalline gallium nitride (GaN) nanorods, ∼100 nm in size with lattice constants of 260, 280, and 300 nm with photonic band gap in the visible region. This unique GaN structure is created through a combined approach of a layer-by-layer template fabrication technique and selective metal organic chemical vapor deposition (MOCVD). These GaN 3DPC exhibit a stacking direction band gap characterized by strong optical reflectance between 380 and 500 nm. By introducing a "line-defect" cavity in the fifth (middle) layer of the 3DPC, a localized transmission mode with a quality factor of 25-30 is also observed within the photonic band gap. The realization of a group III nitride 3DPC with uniform features and a band gap at wavelengths in the visible region is an important step toward realizing complete control of the electromagnetic environment for group III nitride based optoelectronic devices.

  1. Investigation on gallium ions impacting monolayer graphene

    Directory of Open Access Journals (Sweden)

    Xin Wu

    2015-06-01

    Full Text Available In this paper, the physical phenomena of gallium (Ga+ ion impacting monolayer graphene in the nanosculpting process are investigated experimentally, and the mechanisms are explained by using Monte Carlo (MC and molecular dynamics (MD simulations. Firstly, the MC method is employed to clarify the phenomena happened to the monolayer graphene target under Ga+ ion irradiation. It is found that substrate has strong influence on the damage mode of graphene. The mean sputtering yield of graphene under 30 keV Ga+ ion irradiation is 1.77 and the least ion dose to completely remove carbon atoms in graphene is 21.6 ion/nm2. Afterwards, the focused ion beam over 21.6 ion/nm2 is used for the irradiation on a monolayer graphene supported by SiO2 experimentally, resulting in the nanostructures, i.e., nanodot and nanowire array on the graphene. The performances of the nanostructures are characterized by atomic force microscopy and Raman spectrum. A plasma plume shielding model is put forward to explain the nanosculpting results of graphene under different irradiation parameters. In addition, two damage mechanisms are found existing in the fabrication process of the nanostructures by using empirical MD simulations. The results can help us open the possibilities for better control of nanocarbon devices.

  2. Investigation on gallium ions impacting monolayer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xin; Zhao, Haiyan, E-mail: hyzhao@tsinghua.edu.cn; Yan, Dong; Pei, Jiayun [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084, P. R. Chinaand Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

    2015-06-15

    In this paper, the physical phenomena of gallium (Ga{sup +}) ion impacting monolayer graphene in the nanosculpting process are investigated experimentally, and the mechanisms are explained by using Monte Carlo (MC) and molecular dynamics (MD) simulations. Firstly, the MC method is employed to clarify the phenomena happened to the monolayer graphene target under Ga{sup +} ion irradiation. It is found that substrate has strong influence on the damage mode of graphene. The mean sputtering yield of graphene under 30 keV Ga{sup +} ion irradiation is 1.77 and the least ion dose to completely remove carbon atoms in graphene is 21.6 ion/nm{sup 2}. Afterwards, the focused ion beam over 21.6 ion/nm{sup 2} is used for the irradiation on a monolayer graphene supported by SiO2 experimentally, resulting in the nanostructures, i.e., nanodot and nanowire array on the graphene. The performances of the nanostructures are characterized by atomic force microscopy and Raman spectrum. A plasma plume shielding model is put forward to explain the nanosculpting results of graphene under different irradiation parameters. In addition, two damage mechanisms are found existing in the fabrication process of the nanostructures by using empirical MD simulations. The results can help us open the possibilities for better control of nanocarbon devices.

  3. Chemical stability and electrical performance of dual-active-layered zinc-tin-oxide/indium-gallium-zinc-oxide thin-film transistors using a solution process.

    Science.gov (United States)

    Kim, Chul Ho; Rim, You Seung; Kim, Hyun Jae

    2013-07-10

    We investigated the chemical stability and electrical properties of dual-active-layered zinc-tin-oxide (ZTO)/indium-gallium-zinc-oxide (IGZO) structures (DALZI) with the durability of the chemical damage. The IGZO film was easily corroded or removed by an etchant, but the DALZI film was effectively protected by the high chemical stability of ZTO. Furthermore, the electrical performance of the DALZI thin-film transistor (TFT) was improved by densification compared to the IGZO TFT owing to the passivation of the pin holes or pore sites and the increase in the carrier concentration due to the effect of Sn(4+) doping.

  4. Antibacterial effect of gallium and silver on Pseudomonas aeruginosa treated with gallium-silver-phosphate-based glasses.

    Science.gov (United States)

    Valappil, Sabeel P; Higham, Susan M

    2014-01-01

    Gallium and silver incorporated phosphate-based glasses were evaluated for antibacterial effect on the growth of Pseudomonas aeruginosa, which is a leading cause of opportunistic infections. The glasses were produced by conventional melt quenching methods at 1100°C for 1 h. Glass degradation studies were conducted by weight loss method. Disc diffusion assay and cell viability assay displayed statistically significant (p ≤ 0.0005) effect on P. aeruginosa growth which increased with decreasing calcium content in the glasses. The gallium ion release rates (1.83, 0.69 and 0.48 ppm·h(-1)) and silver ion release rates (2.97, 2.84 and 2.47 ppm·h(-1)) were found to account for this variation. Constant depth film fermentor was used to evaluate the anti-biofilm properties of the glasses. Both gallium and silver in the glass contributed to biofilm growth inhibitory effect on P. aeruginosa (up to 2.68 reduction in log 10 values of the viable counts compared with controls). The glasses were found to deliver gallium and silver in a controlled way and exerted cumulative antibacterial action on planktonic and biofilm growth of P. aeruginosa. The antibacterial, especially anti-biofilm, properties of the gallium and silver incorporated phosphate-based glasses make them a potential candidate to combat infections caused by P. aeruginosa.

  5. Spectrofluorimetric determination of gallium with calon-carboxylic acid

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A simple and sensitive spectrofluorimetric procedure for the analysis of microquantities of gallium in alloy wasdescribed. The method is based on the formation of Ga(Ⅲ)-CCA (calon-carboxylic acid) complex. The emission of thefluorescent complex was measured at λ = 620 nm with excitation at λ = 584 nm. A good linearity was found in the galliumrange of 0.7-280 ng/mL. The precision of the method is good and the relative standard deviation is 1.9% for a gallium stan-dard solution of 70 ng/mL. The procedure was proved to be suitable in terms of accuracy and selectivity for the mi-croamount of gallium in alloy.

  6. Photoconductive Properties of Brush Plated Copper Indium Gallium Selenide Films

    Directory of Open Access Journals (Sweden)

    N. P. Subiramaniyam

    2013-01-01

    Full Text Available Copper indium gallium selenide (CIGS films were deposited for the first time by the brush electrodeposition technique. X-ray diffraction studies indicated the formation of single phase chalcopyrite CIGS. Lattice parameters, dislocation density, and strain were calculated. Band gap of the films increased from 1.12 eV to 1.63 eV as the gallium concentration increased. Room temperature transport parameters of the films, namely, resistivity increased from 0.10 ohm cm to 12 ohm cm, mobility decreased from 125 cm2V−1s−1 to 20.9 cm2V−1s−1, and carrier concentration decreased from 4.99 × 1017 cm−3 to 2.49 × 1016 cm−3 as the gallium concentration increased. Photosensitivity of the films increased linearly with intensity of illumination and with increase of applied voltage.

  7. Gallium scintigraphy in Hansen's disease

    Energy Technology Data Exchange (ETDEWEB)

    Braga, F.J.H.N. (Hopital Henri-Mondor, 75 - Paris (France). Service de Biophysique de Medecine Nucleaire Sao Paulo Univ., SP (Brazil). Centro de Medicina Nuclear); Araejo, E.B.; Camargo, E.E. (Sao Paulo Univ., SP (Brazil). Centro de Medicina Nuclear); Tedesco-Marchesi, L.C.M.; Rivitti, M.C.M. (Sao Paulo Univ., SP (Brazil). Servicio de Dermatologia); Bouladour, H.; Galle, P. (Hopital Henri-Mondor, 75 - Paris (France). Service de Biophysique de Medecine Nucleaire)

    1991-11-01

    Gallium 67 imaging was used in 12 patients with documented Hansen's disease undergoing treatment or not in an attempt to determine the pattern of the disease. Diagnosis was confirmed by histopathology in all patients. The Mitsuda reaction was seen in all patients. Specific nuclear studies were performed when needed to evaluate particular organs better. Gallium 67 images show homogeneous, diffuse and moderate accumulation over the entire skin surface (except for the face) of untreated patients with multibacillary disease. The face skin in these cases presented homogeneous, diffuse but very marked uptake of gallium. Internal organ involvement was variable. There was a very good correlation among clinical, scintigraphical, immunological and histopathological data. The pattern of the body skin ('skin outlining') and face skin ('beard distribution') may be distinct for untreated patients with multibacillary leprosy. (orig.).

  8. Electron Transport Layer-Free Inverted Organic Solar Cells Fabricated with Highly Transparent Low-Resistance Indium Gallium Zinc Oxide/Ag/Indium Gallium Zinc Oxide Multilayer Electrode

    Science.gov (United States)

    Kim, Jun Ho; Kwon, Sung-Nam; Na, Seok-In; Kim, Sun-Kyung; Yoo, Young-Zo; Im, Hyeong-Seop; Seong, Tae-Yeon

    2017-04-01

    Inverted organic solar cells (OSCs) have been fabricated with conventional Sn-doped indium oxide (ITO) and amorphous indium gallium zinc oxide (a-IGZO)/Ag/a-IGZO (39 nm/19 nm/39 nm) (a-IAI) electrodes and their electrical characteristics characterized. The ITO and optimized a-IAI electrodes showed high transmittance of 96% and 88% at 500 nm, respectively. The carrier concentration and sheet resistance of the ITO and a-IAI films were 8.46 × 1020 cm-3 and 7.96 × 1021 cm-3 and 14.18 Ω/sq and 4.24 Ω/sq, respectively. Electron transport layer (ETL)-free OSCs with the a-IAI electrode exhibited power conversion efficiency (PCE) of 2.66%, similar to that of ZnO ETL-based OSCs with ITO electrode (3.27%). However, the ETL-free OSCs with the a-IAI electrode showed much higher PCE than the ETL-free OSCs with the ITO electrode (0.84%). Ultraviolet photoelectron spectroscopy results showed that the work function of the a-IAI electrode was 4.15 eV. This improved performance was attributed to the various roles of the a-IAI electrode, e.g., as an effective ETL and a hole blocking layer.

  9. A Study of Ga(.47)In(.53)As and Al(.48)In(.52)As for Very High Frequency Device Applications.

    Science.gov (United States)

    1985-01-01

    GaInAs/AlInAs modulation doped structures grown by molecular beam epitaxy (MBE) were studied. The parameters of the MBE growth were adjusted to give high room temperature mobilities (-12000 sq cm/v-sec) and high sheet electron concentrations 2 x 10 to the 12th power per sq cm. Because of higher electron velocities and high conductivities GaInAs modulation doped transistors should be significantly higher speed than those of GaAs. Originator-Supplied keywords include: Gallium indium arsenide, Aluminum indium arsenide, Indium phosphide, Modulation

  10. Extremely-efficient, miniaturized, long-lived alpha-voltaic power source using liquid gallium

    Science.gov (United States)

    Snyder, G. Jeffrey (Inventor); Patel, Jagdishbhai (Inventor); Fleurial, Jean-Pierre (Inventor)

    2004-01-01

    A power source converts .alpha.-particle energy to electricity for use in electrical systems. Liquid gallium or other liquid medium is subjected to .alpha.-particle emissions. Electrons are freed by collision from neutral gallium atoms to provide gallium ions. The electrons migrate to a cathode while the gallium ions migrate to an anode. A current and/or voltage difference then arises between the cathode and anode because of the work function difference of the cathode and anode. Gallium atoms are regenerated by the receiving of electrons from the anode enabling the generation of additional electrons from additional .alpha.-particle collisions.

  11. Photoconductive Properties of Brush Plated Copper Indium Gallium Selenide Films

    OpenAIRE

    Subiramaniyam, N. P.; P. Thirunavukkarasu; Murali, K. R.

    2013-01-01

    Copper indium gallium selenide (CIGS) films were deposited for the first time by the brush electrodeposition technique. X-ray diffraction studies indicated the formation of single phase chalcopyrite CIGS. Lattice parameters, dislocation density, and strain were calculated. Band gap of the films increased from 1.12 eV to 1.63 eV as the gallium concentration increased. Room temperature transport parameters of the films, namely, resistivity increased from 0.10 ohm cm to 12 ohm cm, mobility decre...

  12. Neutron detection using boron gallium nitride semiconductor material

    OpenAIRE

    Katsuhiro Atsumi; Yoku Inoue; Hidenori Mimura; Toru Aoki; Takayuki Nakano

    2014-01-01

    In this study, we developed a new neutron-detection device using a boron gallium nitride (BGaN) semiconductor in which the B atom acts as a neutron converter. BGaN and gallium nitride (GaN) samples were grown by metal organic vapor phase epitaxy, and their radiation detection properties were evaluated. GaN exhibited good sensitivity to α-rays but poor sensitivity to γ-rays. Moreover, we confirmed that electrons were generated in the depletion layer under neutron irradiation. This resulted in ...

  13. Magnetostriction and magnetic heterogeneities in iron-gallium.

    Science.gov (United States)

    Laver, M; Mudivarthi, C; Cullen, J R; Flatau, A B; Chen, W-C; Watson, S M; Wuttig, M

    2010-07-09

    Iron-gallium alloys Fe(1-x)Ga(x) exhibit an exceptional increase in magnetostriction with gallium content. We present small-angle neutron scattering investigations on a Fe(0.81)Ga(0.19) single crystal. We uncover heterogeneities with an average spacing of 15 nm and with magnetizations distinct from the matrix. The moments in and around the heterogeneities are observed to reorient with an applied magnetic field or mechanical strain. We discuss the possible roles played by nanoscale magnetic heterogeneities in the mechanism for magnetostriction in this material.

  14. Magnetostriction and Magnetic Heterogeneities in Iron-Gallium

    DEFF Research Database (Denmark)

    Laver, Mark; Mudivarthi, C.; Cullen, J.R.;

    2010-01-01

    Iron-gallium alloys Fe1-xGax exhibit an exceptional increase in magnetostriction with gallium content. We present small-angle neutron scattering investigations on a Fe0.81Ga0.19 single crystal. We uncover heterogeneities with an average spacing of 15 nm and with magnetizations distinct from...... the matrix. The moments in and around the heterogeneities are observed to reorient with an applied magnetic field or mechanical strain. We discuss the possible roles played by nanoscale magnetic heterogeneities in the mechanism for magnetostriction in this material. © 2010 The American Physical Society...

  15. Laser spectroscopy of gallium isotopes using the ISCOOL RFQ cooler

    CERN Multimedia

    Blaum, K; Kowalska, M; Ware, T; Procter, T J

    2007-01-01

    We propose to study the radioisotopes of gallium (Z=31) by collinear laser spectroscopy using the ISCOOL RFQ ion cooler. The proposed measurements on $^{62-83}$Ga will span both neutron-deficient and neutron-rich isotopes. Of key interest is the suggested development of a proton-skin in the neutron-deficient isotopes. The isotope shifts measured by laser spectroscopy will be uniquely sensitive to this feature. The measurements will also provide a wealth of new information on the gallium nuclear spins, static moments and nuclear charge radii.

  16. Pseudomembranous colitis: a possible role for Gallium scanning

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, E.L.; Charap, M.; Sanger, J.J.; Tiu, S.S.

    1983-10-01

    A case of antibiotic-associated pseudomembranous colitis is presented in which the Gallium scan was the first diagnostic modality to alert the clinicians to the existence of an inflammatory bowel process. The mechanism of localization of the radiopharmaceutical in inflammatory bowel disease is discussed. Although colonoscopy is far more specific and should be the first-line diagnostic tool used in assessing the presence of pseudomembranous colitis, Gallium scanning may have a role in the follow-up of treatment and in cases of relapse.

  17. Unintentional gallium incorporation in InGaN layers during epitaxial growth

    Science.gov (United States)

    Zhou, Kun; Ren, Huaijin; Ikeda, Masao; Liu, Jianping; Ma, Yi; Gao, Songxin; Tang, Chun; Li, Deyao; Zhang, Liquan; Yang, Hui

    2017-01-01

    Unintentional gallium incorporation was observed and investigated in the epitaxial growth of InGaN by metalorganic vapor phase epitaxy. InGaN was grown without intentional gallium precursor and the gallium incorporation rate was found not dependent on TEGa source but was significantly influenced by temperature and TMIn source flow. The source of the unintentional gallium incorporation is confirmed to be from the flow distributor of the reactor. The incorporation mechanism was analyzed to be the diffusion of resultant of transmetalation reaction between TMIn or its decomposed products (for example DMIn) and residual gallium. Due to the unintentional gallium incorporation, the growth rate and indium content of InGaN layer are determined by indium source, gallium source and the growth temperature.

  18. Photoelectrochemical reduction of carbon dioxide using Ge doped GaN nanowire photoanodes

    Directory of Open Access Journals (Sweden)

    Yichen Wang

    2015-11-01

    Full Text Available We report on the direct conversion of carbon dioxide (CO2 in a photoelectrochemical cell consisting of germanium doped gallium nitride nanowire anode and copper (Cu cathode. Various products including methane (CH4, carbon monoxide (CO, and formic acid (HCOOH were observed under light illumination. A Faradaic efficiency of ∼10% was measured for HCOOH. Furthermore, this photoelectrochemical system showed enhanced stability for 6 h CO2 reduction reaction on low cost, large area Si substrates.

  19. Exchange of iron by gallium in siderophores.

    Science.gov (United States)

    Emery, T

    1986-08-12

    Siderophores are iron transport compounds produced by numerous microorganisms and which strongly chelate Fe(III), but not Fe(II). Other trivalent metals, such as Al(III), Cr(III), or Ga(III), are not capable of significantly displacing iron from siderophores. However, I demonstrate here that Ga(III) can effectively displace iron under reducing conditions. With ascorbate as reductant and ferrozine as Fe(II) trapping agent, the kinetics of reductive displacement of iron by Ga(III) were followed spectroscopically by the increase of absorbance at 562 nm due to formation of the Fe(II)-ferrozine complex. No significant reduction of siderophore occurred in the absence of Ga(III). With excess Ga(III), the displacement was quantitative and very rapid. The rate of metal exchange was pseudo first order with respect to Ga(III) concentration and highly pH dependent, suggesting that siderophore ligands are displaced from the iron in a concerted mechanism by Ga(III) and protonation to expose the Fe(III) to reduction by ascorbate. Reaction rates were dependent upon the structure of the siderophore, being greatest for ferric rhodotorulic acid and slowest for ferrichrome A at pH 5.4. The pH profile for ferric rhodotorulic acid was unusual in that it showed a maximum at pH 6.5, while all other siderophores examined showed an increase in rate as pH was lowered from 7.0. The physiological significance of this reaction to the clinical use of gallium is discussed.

  20. NMR studies on the new iron arsenide superconductors including the superconducting state

    Energy Technology Data Exchange (ETDEWEB)

    Grafe, Hans-Joachim; Lang, Guillaume; Hammerath, Franziska; Manthey, Katarina; Behr, Guenther; Werner, Jochen; Buechner, Bernd [IFW Dresden, Helmholtzstr. 20, D-01069 Dresden (Germany); Paar, Dalibor [IFW Dresden, Helmholtzstr. 20, D-01069 Dresden (Germany); Dept. of Physics, Faculty of Science, Univ. of Zagreb (Croatia); Curro, Nicholas [Dept. of Physics, Univ. of California, Davis, CA 95616 (United States)

    2009-07-01

    We summarize our Nuclear Magnetic Resonance (NMR) and Nuclear Quadrupole Resonance (NQR) results on the new iron arsenide superconductor LaO{sub 1-x}F{sub x}FeAs in the normal state, and show new NMR data in the superconducting state. Beyond early evidence of nodes and spin-singlet pairing[2], we find evidence of a deviation of the T{sup 3} behaviour of the spin lattice relaxation rate, 1/T{sub 1}, at temperatures significantly below T{sub c}, which would agree with the suggested extended s-wave symmetry. The deviation of the T{sup 3} behaviour is induced by the pair breaking effect of impurities. Different amounts of impurities would lead to different temperature dependences of 1/T{sub 1}, which would allow to differentiate between d-wave and extended s-wave symmetries.

  1. Methods for forming group III-V arsenide-nitride semiconductor materials

    Science.gov (United States)

    Major, Jo S. (Inventor); Welch, David F. (Inventor); Scifres, Donald R. (Inventor)

    2000-01-01

    Methods are disclosed for forming Group III--arsenide-nitride semiconductor materials. Group III elements are combined with group V elements, including at least nitrogen and arsenic, in concentrations chosen to lattice match commercially available crystalline substrates. Epitaxial growth of these III-V crystals results in direct bandgap materials, which can be used in applications such as light emitting diodes and lasers. Varying the concentrations of the elements in the III-V crystals varies the bandgaps, such that materials emitting light spanning the visible spectra, as well as mid-IR and near-UV emitters, can be created. Conversely, such material can be used to create devices that acquire light and convert the light to electricity, for applications such as full color photodetectors and solar energy collectors. The growth of the III-V crystals can be accomplished by growing thin layers of elements or compounds in sequences that result in the overall lattice match and bandgap desired.

  2. Synthesis of gallium nitride nanostructures by nitridation of electrochemically deposited gallium oxide on silicon substrate

    Science.gov (United States)

    Ghazali, Norizzawati Mohd; Yasui, Kanji; Hashim, Abdul Manaf

    2014-12-01

    Gallium nitride (GaN) nanostructures were successfully synthesized by the nitridation of the electrochemically deposited gallium oxide (Ga2O3) through the utilization of a so-called ammoniating process. Ga2O3 nanostructures were firstly deposited on Si substrate by a simple two-terminal electrochemical technique at a constant current density of 0.15 A/cm2 using a mixture of Ga2O3, HCl, NH4OH and H2O for 2 h. Then, the deposited Ga2O3 sample was ammoniated in a horizontal quartz tube single zone furnace at various ammoniating times and temperatures. The complete nitridation of Ga2O3 nanostructures at temperatures of 850°C and below was not observed even the ammoniating time was kept up to 45 min. After the ammoniating process at temperature of 900°C for 15 min, several prominent diffraction peaks correspond to hexagonal GaN (h-GaN) planes were detected, while no diffraction peak of Ga2O3 structure was detected, suggesting a complete transformation of Ga2O3 to GaN. Thus, temperature seems to be a key parameter in a nitridation process where the deoxidization rate of Ga2O3 to generate gaseous Ga2O increase with temperature. The growth mechanism for the transformation of Ga2O3 to GaN was proposed and discussed. It was found that a complete transformation can not be realized without a complete deoxidization of Ga2O3. A significant change of morphological structures takes place after a complete transformation of Ga2O3 to GaN where the original nanorod structures of Ga2O3 diminish, and a new nanowire-like GaN structures appear. These results show that the presented method seems to be promising in producing high-quality h-GaN nanostructures on Si.

  3. Discovery of Gallium, Germanium, Lutetium, and Hafnium Isotopes

    CERN Document Server

    Gross, J L

    2011-01-01

    Currently, twenty-eight gallium, thirty-one germanium, thirty-five lutetium, and thirty-six hafnium isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented.

  4. [Dimensional changes of silver and gallium-based alloy].

    Science.gov (United States)

    Ballester, R Y; Markarian, R A; Loguercio, A D

    2001-01-01

    Gallium-based dental alloys were created with the aim of solving the problem of toxicity of mercury. The material shows mechanical properties similar to those of dental amalgam, but researches point out two unfavorable characteristics: great corrosion and excessive post-setting expansion, and the latter is capable of cracking dental structures. The aim of this study was to evaluate, during 7 days, the in vitro dimensional alteration of a gallium dental alloy (Galloy, SDI, Australia), in comparison with a dental amalgam containing zinc (F400, SDI, Australia), as a function of the contact with saline solution (0.9% NaCl) during the setting period. The storage experimental conditions were: storage in dry environment, immersion in saline solution and contamination during condensation. Additionally, the effects of contamination during the trituration of dental amalgam and the effects of protecting the surface of the gallium alloy with a fluid resin were studied. Specimens were stored at 37 degrees C +/- 1 degree C, and measuring was carried out, sequentially, every 24 h during 7 days. When the gallium alloy was either contaminated or immersed, an expansion significantly greater than that observed in the other experimental conditions was noticed after 7 days. The application of a fluid resin to protect the surface of the cylinders was able to avoid the increase in expansion caused by superficial moisture. The amalgam alloy did not show significant dimensional alterations, except when it was contaminated during trituration.

  5. Gallium Nitride MMICs for mm-Wave Power Operation

    NARCIS (Netherlands)

    Quay, R.; Maroldt, S.; Haupt, C.; Heijningen, M. van; Tessmann, A.

    2009-01-01

    In this paper a Gallium Nitride MMIC technology for high-power amplifiers between 27 GHz and 101 GHz based on 150 nm- and 100 nm-gate technologies is presented. The GaN HEMT MMICs are designed using coplanar waveguide transmission-line-technology on 3-inch semi-insulating SiC substrates. The measure

  6. Targeting Gallium to Cancer Cells through the Folate Receptor

    Directory of Open Access Journals (Sweden)

    Nerissa Viola-Villegas

    2008-01-01

    Full Text Available The development of gallium(III compounds as anti-cancer agents for both treatment and diagnosis is a rapidly developing field of research. Problems remain in exploring the full potential of gallium(III as a safe and successful therapeutic agent or as an imaging agent. One of the major issues is that gallium(III compounds have little tropism for cancer cells. We have combined the targeting properties of folic acid (FA with long chain liquid polymer poly(ethylene glycol (PEG ‘spacers’. This FA-PEG unit has been coupled to the gallium coordination complex of 1,4,7,10-tetraazacyclo-dodecane-N,N′,N′′,N′′′-tetraacetic acid (DOTA through amide linkages for delivery into target cells overexpressing the folate receptor (FR. In vitro cytotoxicity assays were conducted against a multi-drug resistant ovarian cell line (A2780/AD that overexpresses the FR and contrasted against a FR free Chinese hamster ovary (CHO cell line. Results are rationalized taking into account stability studies conducted in RPMI 1640 media and HEPES buffer at pH 7.4.

  7. In-Plane Electronic Anisotropy of Underdoped ___122___ Fe-Arsenide Superconductors Revealed by Measurements of Detwinned Single Crystals

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, Ian Randal

    2012-05-08

    The parent phases of the Fe-arsenide superconductors harbor an antiferromagnetic ground state. Significantly, the Neel transition is either preceded or accompanied by a structural transition that breaks the four fold symmetry of the high-temperature lattice. Borrowing language from the field of soft condensed matter physics, this broken discrete rotational symmetry is widely referred to as an Ising nematic phase transition. Understanding the origin of this effect is a key component of a complete theoretical description of the occurrence of superconductivity in this family of compounds, motivating both theoretical and experimental investigation of the nematic transition and the associated in-plane anisotropy. Here we review recent experimental progress in determining the intrinsic in-plane electronic anisotropy as revealed by resistivity, reflectivity and ARPES measurements of detwinned single crystals of underdoped Fe arsenide superconductors in the '122' family of compounds.

  8. The Coefficients of Thermal Expansion of Boron Arsenide (B12As2) Between 25 C and 850 C

    Energy Technology Data Exchange (ETDEWEB)

    Whiteley, Clinton E. [Kansas State University; Kirkham, Melanie J [ORNL; Edgar, J H [Kansas State University

    2013-01-01

    The semiconductor boron arsenide has a high 10B density, a wide bandgap, and a high melting temperature, all of which make it an interesting candidate for high-temperature electronic devices and radiation detectors. The present investigation was undertaken to determine the coefficients of thermal expansion for boron arsenide. B12As2 powder was synthesized from boron and arsenic heated in a sealed quartz ampoule at 1100 C for 72 hrs with excess boron. Using high temperature X-ray diffraction (HTXRD) between 25 C and 850 C, the average lattice coefficients of thermal expansion were measured perpendicular and parallel to the <111> axis in the rhombohedral setting (equivalent to the a and c axes in the hexagonal setting): 4.9x10-6 K-1 and 5.3x10-6 K-1, respectively. The average unit cell volumetric coefficient of thermal expansion was determined to be 1.5x10-5 K-1.

  9. Deep levels in Ga-doped ZnSe grown by molecular-beam epitaxy

    Science.gov (United States)

    Venkatesan, S.; Pierret, R. F.; Qiu, J.; Kobayashi, M.; Gunshor, R. L.; Kolodziejski, L. A.

    1989-10-01

    Results of a deep-level transient spectroscopy study of Ga-doped ZnSe thin films grown by molecular-beam epitaxy are presented. Two prominent deep levels were observed in all the samples investigated. The concentration of the trap detected at 0.34 eV below the conduction-band edge was essentially independent of the doping concentration and is attributed to native defects arising from Se vacancies in the ZnSe films. The second level with an activation energy of 0.26 eV shows a very strong doping dependence and is tentatively identified as arising from dopant-site (gallium-on-zinc-site) defects complexed with selenium vacancies. Preliminary results also indicate that planar doping of ZnSe significantly reduces the concentration of the Ga-vacancy complex.

  10. Dual doped monolayer and bilayer graphene: The case of 4p and 2p elements

    Science.gov (United States)

    Denis, Pablo A.; Iribarne, Federico

    2016-08-01

    4p/2p dual-doped monolayer and bilayer graphene were studied via first principle calculations. Generally, dopants prefer to be agglomerated. A second dopant significantly reduces formation energies. Thus, partially reduced graphene oxide would favor substitutional doping by facilitating the introduction of the 4p dopants. Dual-doping can tune the band gap from 0.1 to 0.8 eV. For bilayer graphene, large atomic radii elements (Gallium and Germanium) form interlayer bonds with the undoped sheet. For some dual-doped graphenes, interlayer GaC and GeC bonds were formed, increasing the chemical reactivity of the undoped layer and affecting its electronic structure, with metallic or semiconducting characters observed.

  11. Boron Arsenide and Boron Phosphide for High Temperature and Luminescent Devices. [semiconductor devices - crystal growth/crystal structure

    Science.gov (United States)

    Chu, T. L.

    1975-01-01

    The crystal growth of boron arsenide and boron phosphide in the form of bulk crystals and epitaxial layers on suitable substrates is discussed. The physical, chemical, and electrical properties of the crystals and epitaxial layers are examined. Bulk crystals of boron arsenide were prepared by the chemical transport technique, and their carrier concentration and Hall mobility were measured. The growth of boron arsenide crystals from high temperature solutions was attempted without success. Bulk crystals of boron phosphide were also prepared by chemical transport and solution growth techniques. Techniques required for the fabrication of boron phosphide devices such as junction shaping, diffusion, and contact formation were investigated. Alloying techniques were developed for the formation of low-resistance ohmic contacts to boron phosphide. Four types of boron phosphide devices were fabricated: (1) metal-insulator-boron phosphide structures, (2) Schottky barriers; (3) boron phosphide-silicon carbide heterojunctions; and (4) p-n homojunctions. Easily visible red electroluminescence was observed from both epitaxial and solution grown p-n junctions.

  12. Demonstrating the capability of the high-performance plasmonic gallium-graphene couple.

    Science.gov (United States)

    Losurdo, Maria; Yi, Congwen; Suvorova, Alexandra; Rubanov, Sergey; Kim, Tong-Ho; Giangregorio, Maria M; Jiao, Wenyuan; Bergmair, Iris; Bruno, Giovanni; Brown, April S

    2014-03-25

    Metal nanoparticle (NP)-graphene multifunctional platforms are of great interest for exploring strong light-graphene interactions enhanced by plasmons and for improving performance of numerous applications, such as sensing and catalysis. These platforms can also be used to carry out fundamental studies on charge transfer, and the findings can lead to new strategies for doping graphene. There have been a large number of studies on noble metal Au-graphene and Ag-graphene platforms that have shown their potential for a number of applications. These studies have also highlighted some drawbacks that must be overcome to realize high performance. Here we demonstrate the promise of plasmonic gallium (Ga) nanoparticle (NP)-graphene hybrids as a means of modulating the graphene Fermi level, creating tunable localized surface plasmon resonances and, consequently, creating high-performance surface-enhanced Raman scattering (SERS) platforms. Four prominent peculiarities of Ga, differentiating it from the commonly used noble (gold and silver) metals are (1) the ability to create tunable (from the UV to the visible) plasmonic platforms, (2) its chemical stability leading to long-lifetime plasmonic platforms, (3) its ability to n-type dope graphene, and (4) its weak chemical interaction with graphene, which preserves the integrity of the graphene lattice. As a result of these factors, a Ga NP-enhanced graphene Raman intensity effect has been observed. To further elucidate the roles of the electromagnetic enhancement (or plasmonic) mechanism in relation to electron transfer, we compare graphene-on-Ga NP and Ga NP-on-graphene SERS platforms using the cationic dye rhodamine B, a drug model biomolecule, as the analyte.

  13. Gallium ion implantation greatly reduces thermal conductivity and enhances electronic one of ZnO nanowires

    Directory of Open Access Journals (Sweden)

    Minggang Xia

    2014-05-01

    Full Text Available The electrical and thermal conductivities are measured for individual zinc oxide (ZnO nanowires with and without gallium ion (Ga+ implantation at room temperature. Our results show that Ga+ implantation enhances electrical conductivity by one order of magnitude from 1.01 × 103 Ω−1m−1 to 1.46 × 104 Ω−1m−1 and reduces its thermal conductivity by one order of magnitude from 12.7 Wm−1K−1 to 1.22 Wm−1K−1 for ZnO nanowires of 100 nm in diameter. The measured thermal conductivities are in good agreement with those in theoretical simulation. The increase of electrical conductivity origins in electron donor doping by Ga+ implantation and the decrease of thermal conductivity is due to the longitudinal and transverse acoustic phonons scattering by Ga+ point scattering. For pristine ZnO nanowires, the thermal conductivity decreases only two times when its diameter reduces from 100 nm to 46 nm. Therefore, Ga+-implantation may be a more effective method than diameter reduction in improving thermoelectric performance.

  14. Enhanced efficiency of Schottky-barrier solar cell with periodically nonhomogeneous indium gallium nitride layer

    Science.gov (United States)

    Anderson, Tom H.; Mackay, Tom G.; Lakhtakia, Akhlesh

    2017-01-01

    A two-dimensional finite-element model was developed to simulate the optoelectronic performance of a Schottky-barrier solar cell. The heart of this solar cell is a junction between a metal and a layer of n-doped indium gallium nitride (InξGaN) alloy sandwiched between a reflection-reducing front window and a periodically corrugated metallic back reflector. The bandgap of the InξGaN layer was varied periodically in the thickness direction by varying the parameter ξ∈(0,1). First, the frequency-domain Maxwell postulates were solved to determine the spatial profile of photon absorption and, thus, the generation of electron-hole pairs. The AM1.5G solar spectrum was taken to represent the incident solar flux. Next, the drift-diffusion equations were solved for the steady-state electron and hole densities. Numerical results indicate that a corrugated back reflector of a period of 600 nm is optimal for photon absorption when the InξGaN layer is homogeneous. The efficiency of a solar cell with a periodically nonhomogeneous InξGaN layer may be higher by as much as 26.8% compared to the analogous solar cell with a homogeneous InξGaN layer.

  15. Basic Equations for the Modeling of Gallium Nitride (gan) High Electron Mobility Transistors (hemts)

    Science.gov (United States)

    Freeman, Jon C.

    2003-01-01

    Gallium nitride (GaN) is a most promising wide band-gap semiconductor for use in high-power microwave devices. It has functioned at 320 C, and higher values are well within theoretical limits. By combining four devices, 20 W has been developed at X-band. GaN High Electron Mobility Transistors (HEMTs) are unique in that the two-dimensional electron gas (2DEG) is supported not by intentional doping, but instead by polarization charge developed at the interface between the bulk GaN region and the AlGaN epitaxial layer. The polarization charge is composed of two parts: spontaneous and piezoelectric. This behavior is unlike other semiconductors, and for that reason, no commercially available modeling software exists. The theme of this document is to develop a self-consistent approach to developing the pertinent equations to be solved. A Space Act Agreement, "Effects in AlGaN/GaN HEMT Semiconductors" with Silvaco Data Systems to implement this approach into their existing software for III-V semiconductors, is in place (summer of 2002).

  16. Design and analysis of vertical-channel gallium nitride (GaN) junctionless nanowire transistors (JNT).

    Science.gov (United States)

    Seo, Jae Hwa; Yoon, Young Jun; Lee, Hwan Gi; Yoo, Gwan Min; Jo, Young-Woo; Son, Dong-Hyeok; Lee, Jung-Hee; Cho, Eou-Sik; Cho, Seongjae; Kang, In Man

    2014-11-01

    Vertical-channel gallium nitride (GaN) junctionless nanowire transistor (JNT) has been designed and characterized by technology computer-aided design (TCAD) simulations. Various characteristics such as wide bandgap, strong polariztion field, and high electron velocity make GaN one of the attractive materials in advanced electronics in recent times. Nanowire-structured GaN can be applicable to various transistors for enhanced electrical performances by its geometrical feature. In this paper, we analyze the direct-current (DC) characteristics depending on various channel doping concentrations (N(ch)) and nanowire radii (R(NW)). Furthermore, the radio-frequency (RF) characteristics under optimized conditions are extracted by small-signal equivalent circuit modeling. For the optimally designed vertical GaN JNT demonstrated on-state current (I(on)) of 345 μA/μm and off-state current (I(off)) of 3.7 x 10(-18) A/μm with a threshold voltage (V(t)) of 0.22 V, and subthreshold swing (S) of 68 mV/dec. Besides, f(T) and f(max) under different operating conditions (gate voltage, V(GS)) have been obtained.

  17. Co-Precipitation Synthesis of Gadolinium Aluminum Gallium Oxide (GAGG) via Different Precipitants

    Science.gov (United States)

    Sun, Yan; Yang, Shenghui; Zhang, Ye; Jiang, Jun; Jiang, Haochuan

    2014-02-01

    In order to obtain a uniform transparent ceramic scintillator, well-dispersed fine starting powders with high-purity, small grain size, spherical morphology and high sinter-ability are necessary. In this study, Ce3+ doped gadolinium aluminum gallium garnet Gd3Al3Ga2O12 (GAGG) powders were synthesized by the co-precipitation method. NH4OH, NH4HCO3 and the mixed solution of NH4OH and NH4HCO3 were used as precipitants, respectively. The precursor composition, phase formation process, microstructure, morphology, particle size distribution and luminescent properties of obtained GAGG powders were measured. The results show that powders prepared using the mixed precipitant exhibit the best microstructural morphology, good sinter-ability and highest luminescent intensity. Pure GAGG polycrystalline powders could be obtained at about 950°C for 1.5 h and the average size of the particles is about 50 nm. The photoluminescence spectrum shows a strong green-yellow emission near 540 nm.

  18. Synthesis of gallium nitride nanostructures by nitridation of electrochemically deposited gallium oxide on silicon substrate.

    Science.gov (United States)

    Ghazali, Norizzawati Mohd; Yasui, Kanji; Hashim, Abdul Manaf

    2014-01-01

    Gallium nitride (GaN) nanostructures were successfully synthesized by the nitridation of the electrochemically deposited gallium oxide (Ga2O3) through the utilization of a so-called ammoniating process. Ga2O3 nanostructures were firstly deposited on Si substrate by a simple two-terminal electrochemical technique at a constant current density of 0.15 A/cm(2) using a mixture of Ga2O3, HCl, NH4OH and H2O for 2 h. Then, the deposited Ga2O3 sample was ammoniated in a horizontal quartz tube single zone furnace at various ammoniating times and temperatures. The complete nitridation of Ga2O3 nanostructures at temperatures of 850°C and below was not observed even the ammoniating time was kept up to 45 min. After the ammoniating process at temperature of 900°C for 15 min, several prominent diffraction peaks correspond to hexagonal GaN (h-GaN) planes were detected, while no diffraction peak of Ga2O3 structure was detected, suggesting a complete transformation of Ga2O3 to GaN. Thus, temperature seems to be a key parameter in a nitridation process where the deoxidization rate of Ga2O3 to generate gaseous Ga2O increase with temperature. The growth mechanism for the transformation of Ga2O3 to GaN was proposed and discussed. It was found that a complete transformation can not be realized without a complete deoxidization of Ga2O3. A significant change of morphological structures takes place after a complete transformation of Ga2O3 to GaN where the original nanorod structures of Ga2O3 diminish, and a new nanowire-like GaN structures appear. These results show that the presented method seems to be promising in producing high-quality h-GaN nanostructures on Si.

  19. The psychology of doping.

    Science.gov (United States)

    Elbe, Anne-Marie; Barkoukis, Vassilis

    2017-08-01

    Doping is increasingly becoming a problem in both elite and recreational sports. It is therefore important to understand the psychological factors which can explain doping behavior in order to prevent it. The present paper briefly presents evidence on the prevalence of doping use in competitive sports and the measurement approaches to assess doping behavior and doping-related variables. Furthermore, the integrative theoretical approaches used to describe the psychological processes underlying doping use are discussed. Finally, the paper provides suggestions for appropriate measurement of doping behavior and doping-related variables, key preventive efforts against doping as well as avenues for future research. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Nanosecond dynamics of a gallium mirror's light-induced reflectivity change

    CERN Document Server

    Albanis, V; Emelyanov, V I; Fedotov, V A; MacDonald, K F; Petropoulos, P M; Richardson, D J; Zheludev, N I

    2000-01-01

    Transient pump-probe optical reflectivity measurements of the nano/microsecond dynamics of a fully reversible, light-induced, surface-assisted metallization of gallium interfaced with silica are reported. The metallization leads to a considerable increase in the interface's reflectivity when solid a-gallium is on the verge of melting. The reflectivity change was found to be a cumulative effect that grows with light intensity and pulse duration. The reflectivity relaxes back to that of alpha-gallium when the excitation is withdrawn in a time that increases critically at gallium's melting point. The effect is attributed to a non-thermal light-induced structural phase transition.

  1. Cutaneous gallium uptake in patients with AIDS with mycobacterium avium-intracellulare septicemia

    Energy Technology Data Exchange (ETDEWEB)

    Allwright, S.J.; Chapman, P.R.; Antico, V.F.; Gruenewald, S.M.

    1988-07-01

    Gallium imaging is increasingly being used for the early detection of complications in patients with AIDS. A 26-year-old homosexual man who was HIV antibody positive underwent gallium imaging for investigation of possible Pneumocystis carinii pneumonia. Widespread cutaneous focal uptake was seen, which was subsequently shown to be due to mycobacterium avium-intracellulare (MAI) septicemia. This case demonstrates the importance of whole body imaging rather than imaging target areas only, the utility of gallium imaging in aiding the early detection of clinically unsuspected disease, and shows a new pattern of gallium uptake in disseminated MAI infection.

  2. Superconductivity in alkali-metal-doped picene.

    Science.gov (United States)

    Mitsuhashi, Ryoji; Suzuki, Yuta; Yamanari, Yusuke; Mitamura, Hiroki; Kambe, Takashi; Ikeda, Naoshi; Okamoto, Hideki; Fujiwara, Akihiko; Yamaji, Minoru; Kawasaki, Naoko; Maniwa, Yutaka; Kubozono, Yoshihiro

    2010-03-04

    Efforts to identify and develop new superconducting materials continue apace, motivated by both fundamental science and the prospects for application. For example, several new superconducting material systems have been developed in the recent past, including calcium-intercalated graphite compounds, boron-doped diamond and-most prominently-iron arsenides such as LaO(1-x)F(x)FeAs (ref. 3). In the case of organic superconductors, however, no new material system with a high superconducting transition temperature (T(c)) has been discovered in the past decade. Here we report that intercalating an alkali metal into picene, a wide-bandgap semiconducting solid hydrocarbon, produces metallic behaviour and superconductivity. Solid potassium-intercalated picene (K(x)picene) shows T(c) values of 7 K and 18 K, depending on the metal content. The drop of magnetization in K(x)picene solids at the transition temperature is sharp (<2 K), similar to the behaviour of Ca-intercalated graphite. The T(c) of 18 K is comparable to that of K-intercalated C(60) (ref. 4). This discovery of superconductivity in K(x)picene shows that organic hydrocarbons are promising candidates for improved T(c) values.

  3. Thermo-chemical properties and electrical resistivity of Zr-based arsenide chalcogenides

    Directory of Open Access Journals (Sweden)

    A. Schlechte, R. Niewa, M. Schmidt, G. Auffermann, Yu. Prots, W. Schnelle, D. Gnida, T. Cichorek, F. Steglich and R. Kniep

    2007-01-01

    Full Text Available Ternary phases in the systems Zr–As–Se and Zr–As–Te were studied using single crystals of ZrAs1.40(1Se0.50(1 and ZrAs1.60(2Te0.40(1 (PbFCl-type of structure, space group P4/nmm as well as ZrAs0.70(1Se1.30(1 and ZrAs0.75(1Te1.25(1 (NbPS-type of structure, space group Immm. The characterization covers chemical compositions, crystal structures, homogeneity ranges and electrical resistivities. At 1223 K, the Te-containing phases can be described with the general formula ZrAsxTe2−x, with 1.53(1≤x≤1.65(1 (As-rich and 0.58(1≤x≤0.75(1 (Te-rich. Both phases are located directly on the tie-line between ZrAs2 and ZrTe2, with no indication for any deviation. Similar is true for the Se-rich phase ZrAsxSe2−x with 0.70(1≤x≤0.75(1. However, the compositional range of the respective As-rich phase ZrAsx−ySe2−x (0.03(1≤y≤0.10(1; 1.42(1≤x≤1.70(1 is not located on the tie-line ZrAs2–ZrSe2, and exhibits a triangular region of existence with intrinsic deviation of the composition towards lower non-metal contents. Except for ZrAs0.75Se1.25, from the homogeneity range of the Se-rich phase, all compounds under investigation show metallic characteristics of electrical resistivity at temperatures >20 K. Related uranium and thorium arsenide selenides display a typical magnetic field-independent rise of the resistivity towards lower temperatures, which has been explained by a non-magnetic Kondo effect. However, a similar observation has been made for ZrAs1.40Se0.50, which, among the Zr-based arsenide chalcogenides, is the only system with a large concentration of intrinsic defects in the anionic substructure.

  4. Neutron detection using boron gallium nitride semiconductor material

    Energy Technology Data Exchange (ETDEWEB)

    Atsumi, Katsuhiro [Department of Electrical and Electronic Engineering, Graduate School of Engineering, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561 (Japan); Inoue, Yoku; Nakano, Takayuki, E-mail: ttnakan@ipc.shizuoka.ac.jp [Department of Electrical and Materials Science, Graduate School of Engineering, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561 (Japan); Mimura, Hidenori; Aoki, Toru [Research Institute of Electronics, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8011 (Japan)

    2014-03-01

    In this study, we developed a new neutron-detection device using a boron gallium nitride (BGaN) semiconductor in which the B atom acts as a neutron converter. BGaN and gallium nitride (GaN) samples were grown by metal organic vapor phase epitaxy, and their radiation detection properties were evaluated. GaN exhibited good sensitivity to α-rays but poor sensitivity to γ-rays. Moreover, we confirmed that electrons were generated in the depletion layer under neutron irradiation. This resulted in a neutron-detection signal after α-rays were generated by the capture of neutrons by the B atoms. These results prove that BGaN is useful as a neutron-detecting semiconductor material.

  5. Ultra-low threshold gallium nitride photonic crystal nanobeam laser

    Energy Technology Data Exchange (ETDEWEB)

    Niu, Nan, E-mail: nanniu@fas.harvard.edu; Woolf, Alexander; Wang, Danqing; Hu, Evelyn L. [School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138 (United States); Zhu, Tongtong; Oliver, Rachel A. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Quan, Qimin [Rowland Institute at Harvard University, Cambridge, Massachusetts 02142 (United States)

    2015-06-08

    We report exceptionally low thresholds (9.1 μJ/cm{sup 2}) for room temperature lasing at ∼450 nm in optically pumped Gallium Nitride (GaN) nanobeam cavity structures. The nanobeam cavity geometry provides high theoretical Q (>100 000) with small modal volume, leading to a high spontaneous emission factor, β = 0.94. The active layer materials are Indium Gallium Nitride (InGaN) fragmented quantum wells (fQWs), a critical factor in achieving the low thresholds, which are an order-of-magnitude lower than obtainable with continuous QW active layers. We suggest that the extra confinement of photo-generated carriers for fQWs (compared to QWs) is responsible for the excellent performance.

  6. Amorphous carbon buffer layers for separating free gallium nitride films

    Science.gov (United States)

    Altakhov, A. S.; Gorbunov, R. I.; Kasharina, L. A.; Latyshev, F. E.; Tarala, V. A.; Shreter, Yu. G.

    2016-11-01

    The possibility of using amorphous diamond-like carbon (DLC) films for self-separation of gallium nitride (GaN) layers grown by hydride vapor-phase epitaxy has been analyzed. DLC films have been synthesized by plasma-enhanced chemical vapor deposition under low pressure on sapphire (Al2O3) substrates with a (0001) crystallographic orientation. The samples have been studied by the methods of Raman scattering and X-ray diffraction analysis. It is shown that thin DLC films affect only slightly the processes of nucleation and growth of gallium nitride films. Notably, the strength of the "GaN film-Al2O3" substrate interface decreases, which facilitates separation of the GaN layers.

  7. Neutron detection using boron gallium nitride semiconductor material

    Directory of Open Access Journals (Sweden)

    Katsuhiro Atsumi

    2014-03-01

    Full Text Available In this study, we developed a new neutron-detection device using a boron gallium nitride (BGaN semiconductor in which the B atom acts as a neutron converter. BGaN and gallium nitride (GaN samples were grown by metal organic vapor phase epitaxy, and their radiation detection properties were evaluated. GaN exhibited good sensitivity to α-rays but poor sensitivity to γ-rays. Moreover, we confirmed that electrons were generated in the depletion layer under neutron irradiation. This resulted in a neutron-detection signal after α-rays were generated by the capture of neutrons by the B atoms. These results prove that BGaN is useful as a neutron-detecting semiconductor material.

  8. Schottky Contact of Gallium on p-Type Silicon

    Directory of Open Access Journals (Sweden)

    B.P. Modi

    2011-01-01

    Full Text Available The evolution of barrier at Schottky contact and its stabilization to value characterized by the barrier height and unambiguous measurement is still being curiously perused as they hold the key control and manufacture of tailor made Schottky devices for a host of existing and potential for future applications in electronics, optoelectronics and microwave devices. In this context, gallium – silicon Schottky diode has been fabricated and analyzed.

  9. CRITICAL ASSESSMENT: Gallium nitride based visible light emitting diodes

    OpenAIRE

    Oliver, Rachel A.

    2016-01-01

    This is the author accepted manuscript. It is currently under an indefinite embargo pending publication by Maney Publishing. Solid state lighting based on light-emitting diodes (LEDs) is a technology with the potential to drastically reduce energy usage, made possible by the development of gallium nitride and its alloys. However, the nitride materials family exhibits high defect densities and, in the equilibrium wurtzite crystal phase, large piezo-electric and polarisation fields arising a...

  10. Error in anti-DNA antibody radioimmunoassay after gallium scanning

    Energy Technology Data Exchange (ETDEWEB)

    Torretti, D.; Rooney, P.; Williams, G.; Decker, J.L.

    1977-03-01

    Significant interference with the accurate measurement of anti-DNA antibodies occurs after gallium-67 scanning. The observed effect is dependent on the radioimmunoassay used. False-negative results are observed with a modified Farr assay whereas false-positive results are noted in the millipore filter assay. These spurious values are the result of persistent radioactivity in the patients' sera after administration of /sup 67/Ga citrate.

  11. Gallium Nitride (GaN) High Power Electronics (FY11)

    Science.gov (United States)

    2012-01-01

    for HPE GaN high electron mobility transistors ( HEMTs ) compared to SiC metal-oxide-semiconductor field effect transistors (MOSFETs). Although a few...Figure 16. Asymmetric rocking curve for an HVPE film grown on an HVPE substrate. ............19 Figure 17. Schematic of a GaN /AlGaN HEMT structure grown...frequency (RF) HEMTs . These considerable investments can be leveraged for GaN HPE. Some people are concerned about the relative scarcity of gallium

  12. Single and double ionization of gallium by electron impact

    Indian Academy of Sciences (India)

    L K Jha

    2002-09-01

    Electron impact single and double ionization cross sections of gallium have been calculated in the binary encounter approximation using accurate expression for including exchange and interference as given by Vriens and Hartree–Fock velocity distributions for the target electrons throughout the calculations. It is concluded that the ionization of 3d shell contributes partly to single ionization and partly to double ionization. The results so obtained show reasonably good agreement with the experimental data.

  13. Adsorption of sugars on Al- and Ga-doped boron nitride surfaces: A computational study

    Energy Technology Data Exchange (ETDEWEB)

    Darwish, Ahmed A. [Center for Nanotechnology, Zewail City of Science and Technology, Giza 12588 (Egypt); Department of Nuclear and Radiation Engineering, Faculty of Engineering, Alexandria University, Alexandria (Egypt); Fadlallah, Mohamed M. [Center for Fundamental Physics, Zewail City of Science and Technology, Giza 12588 (Egypt); Department of Physics, Faculty of Science, Benha University, Benha (Egypt); Badawi, Ashraf [Center for Nanotechnology, Zewail City of Science and Technology, Giza 12588 (Egypt); Maarouf, Ahmed A., E-mail: ahmed.maarouf@egnc.gov.eg [Center for Fundamental Physics, Zewail City of Science and Technology, Giza 12588 (Egypt); Egypt Nanotechnology Center & Department of Physics, Faculty of Science, Cairo University, Giza 12613 (Egypt)

    2016-07-30

    Highlights: • Doping boron nitride sheets with aluminum or gallium atoms significantly enhances their molecular adsorption properties. • Adsorption of glucose or glucosamine on Al- and Ga-doped boron nitride sheets changes the band gap. • Doping concentration changes the bad gap, but has a minor effect on the adsorption energy. - Abstract: Molecular adsorption on surfaces is a key element for many applications, including sensing and catalysis. Non-invasive sugar sensing has been an active area of research due to its importance to diabetes care. The adsorption of sugars on a template surface study is at the heart of matter. Here, we study doped hexagonal boron nitride sheets (h-BNNs) as adsorbing and sensing template for glucose and glucosamine. Using first principles calculations, we find that the adsorption of glucose and glucosamine on h-BNNs is significantly enhanced by the substitutional doping of the sheet with Al and Ga. Including long range van der Waals corrections gives adsorption energies of about 2 eV. In addition to the charge transfer occurring between glucose and the Al/Ga-doped BN sheets, the adsorption alters the size of the band gap, allowing for optical detection of adsorption. We also find that Al-doped boron nitride sheet is better than Ga-doped boron nitride sheet to enhance the adsorption energy of glucose and glucosamine. The results of our work can be potentially utilized when designing support templates for glucose and glucosamine.

  14. Aging and memory effect in magnetoelectric gallium ferrite single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Vijay; Mukherjee, Somdutta [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Mitra, Chiranjib [Department of Physics, Indian Institute of Science Education and Research, Kolkata 741252 (India); Garg, Ashish [Department of Materials Science and Engineering, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Gupta, Rajeev, E-mail: guptaraj@iitk.ac.in [Department of Physics, Indian Institute of Technology Kanpur, Kanpur 208016 (India); Materials Science Programme, Indian Institute of Technology Kanpur, Kanpur 208016 (India)

    2015-02-01

    Here, we present a time and temperature dependent magnetization study to understand the spin dynamics in flux grown single crystals of gallium ferrite (GaFeO{sub 3}), a known magnetoelectric, ferroelectric and ferrimagnet. Results of the magnetic measurements conducted in the field-cooled (FC) and zero-field-cooled (ZFC) protocols in the heating and cooling cycles were reminiscent of a “memory” effect. Subsequent time dependent magnetic relaxation measurements carried out in ZFC mode at 30 K with an intermittent cooling to 20 K in the presence of a small field show that the magnetization in the final wait period tends to follow its initial state which was present before the cooling break taken at 20 K. These observations provide an unambiguous evidence of single crystal gallium ferrite having a spin glass like phase. - Highlights: • Gallium ferrite a room temperature magnetoelectric and ferrimagnetic material. • Spin‐glass like phase at low temperatures below ∼200 K. • Observation of memory and aging effects in GFO.

  15. Aqueous stability of Ga- and N-polar gallium nitride.

    Science.gov (United States)

    Foster, Corey M; Collazo, Ramon; Sitar, Zlatko; Ivanisevic, Albena

    2013-01-08

    The stability of III-nitride semiconductors in various solutions becomes important as researchers begin to integrate them into sensing platforms. This study quantitatively compares the stability of GaN surfaces with different polarities. This type of quantification is important because it represents the first step toward designing semiconductor material interfaces compatible with solution conditions. A stability study of Ga- and N-polar GaN was conducted by immersion of the surfaces in deionized H(2)O, pH 5, pH 9, and H(2)O(2) solutions for 7 days. Inductively coupled plasma mass spectrometry of the solutions was conducted to determine the amount of gallium leached from the surface. X-ray photoelectron spectroscopy and atomic force microscopy were used to compare the treated surfaces to untreated surfaces. The results show that both gallium nitride surface types exhibit the greatest stability in acidic and neutral solutions. Gallium polar surfaces were found to exhibit superior stability to nitrogen polar surfaces in the solutions studied. Our findings highlight the need for further research on surface passivation and functionalization techniques for polar III-nitride semiconductors.

  16. Gallium-68: chemistry and radiolabeled peptides exploring different oncogenic pathways.

    Science.gov (United States)

    Morgat, Clément; Hindié, Elif; Mishra, Anil K; Allard, Michèle; Fernandez, Philippe

    2013-03-01

    Abstract Early and specific tumor detection and also therapy selection and response evaluation are some challenges of personalized medicine. This calls for high sensitive and specific molecular imaging such as positron emission tomography (PET). The use of peptides for PET molecular imaging has undeniable advantages: possibility of targeting through peptide-receptor interaction, small size and low-molecular weight conferring good penetration in the tissue or at cellular level, low toxicity, no antigenicity, and possibility of wide choice for radiolabeling. Among β(+)-emitter radioelements, Gallium-68 is a very attractive positron-emitter compared with carbon-11 or fluorine-18 taking into account its easy production via a (68)Ge/(68)Ga generator and well established radiochemistry. Gallium-68 chemistry is based on well-defined coordination complexes with macrocycle or chelates having strong binding properties, particularly suitable for linking peptides that allow resistance to in vivo transchelation of the metal ion. Understanding specific and nonspecific molecular mechanisms involved in oncogenesis is one major key to develop new molecular imaging tools. The present review focuses on peptide signaling involved in different oncogenic pathways. This peptide signalization might be common for tumoral and non-tumoral processes or could be specific of an oncological process. This review describes gallium chemistry and different (68)Ga-radiolabeled peptides already in use or under development aiming at developing molecular PET imaging of different oncological processes.

  17. Challenges for critical raw material recovery from WEEE - The case study of gallium.

    Science.gov (United States)

    Ueberschaar, Maximilian; Otto, Sarah Julie; Rotter, Vera Susanne

    2017-02-01

    Gallium and gallium compounds are more frequently used in future oriented technologies such as photovoltaics, light diodes and semiconductor technology. In the long term the supply risk is estimated to be critical. Germany is one of the major primary gallium producer, recycler of gallium from new scrap and GaAs wafer producer. Therefore, new concepts for a resource saving handling of gallium and appropriate recycling strategies have to be designed. This study focus on options for a possible recycling of gallium from waste electric and electronic equipment. To identify first starting points, a substance flow analysis was carried out for gallium applied in integrated circuits applied on printed circuit boards and for LEDs used for background lighting in Germany in 2012. Moreover, integrated circuits (radio amplifier chips) were investigated in detail to deduce first approaches for a recycling of such components. An analysis of recycling barriers was carried out in order to investigate general opportunities and risks for the recycling of gallium from chips and LEDs. Results show, that significant gallium losses arose in primary production and in waste management. 93±11%, equivalent to 43,000±4700kg of the total gallium potential was lost over the whole primary production process until applied in electronic goods. The largest share of 14,000±2300kggallium was lost in the production process of primary raw materials. The subsequent refining process was related to additional 6900±3700kg and the chip and wafer production to 21,700±3200kg lost gallium. Results for the waste management revealed only low collection rates for related end-of-life devices. Not collected devices held 300 ± 200 kg gallium. Due to the fact, that current waste management processes do not recover gallium, further 80 ± 10 kg gallium were lost. A thermal pre-treatment of the chips, followed by a manual separation allowed an isolation of gallium rich fractions, with gallium mass fractions up to

  18. Superconductivity in the ternary iridium-arsenide BaIr2As2

    Science.gov (United States)

    Wang, Xiao-Chuan; Ruan, Bin-Bin; Yu, Jia; Pan, Bo-Jin; Mu, Qing-Ge; Liu, Tong; Chen, Gen-Fu; Ren, Zhi-An

    2017-03-01

    Here we report the synthesis and discovery of superconductivity in a novel ternary iridium-arsenide compound BaIr2As2. The polycrystalline BaIr2As2 sample was first synthesized by a high temperature and high pressure method. Crystal structural analysis indicates that BaIr2As2 crystallizes in the ThCr2Si2-type layered tetragonal structure with space group I4/mmm (No. 139), and the lattice parameters were refined to be a = 4.052(9) Å and c = 12.787(8) Å. By the electrical resistivity and magnetic susceptibility measurements we found type-II superconductivity in the new BaIr2As2 compound with a T c (critical temperature) of 2.45 K, and an upper critical field μ 0 H c2(0) about 0.2 T. Low temperature specific heat measurements gave a Debye temperature of about 202 K and a distinct specific jump with ΔC e /γT c = 1.36, which is close to the value of BCS weak coupling limit and confirms the bulk superconductivity in this new BaIr2As2 compound.

  19. Ab-initio Electronic, Transport and Related Properties of Zinc Blende Boron Arsenide (zb-BAs)

    Science.gov (United States)

    Nwigboji, Ifeanyi H.; Malozovsky, Yuriy; Bagayoko, Diola

    We present results from ab-initio, self-consistent density functional theory (DFT) calculations of electronic, transport, and bulk properties of zinc blende boron arsenide (zb-BAs). We utilized a local density approximation (LDA) potential and the linear combination of atomic orbital (LCAO) formalism. Our computational technique follows the Bagayoko, Zhao, and Williams method, as enhanced by Ekuma and Franklin. Our results include electronic energy bands, densities of states, and effective masses. We explain the agreement between these findings, including the indirect band gap, and available, corresponding, experimental ones. This work confirms the capability of DFT to describe accurately properties of materials, provided the computations adhere to the conditions of validity of DFT [AIP Advances, 4, 127104 (2014)]. Acknowledgments: This work was funded in part by the National Science Foundation (NSF) and the Louisiana Board of Regents, through LASiGMA [Award Nos. EPS- 1003897, NSF (2010-15)-RII-SUBR] and NSF HRD-1002541, the US Department of Energy - National, Nuclear Security Administration (NNSA) (Award No. DE- NA0002630), LaSPACE, and LONI-SUBR.

  20. Triamidoamine thorium-arsenic complexes with parent arsenide, arsinidiide and arsenido structural motifs

    Science.gov (United States)

    Wildman, Elizabeth P.; Balázs, Gábor; Wooles, Ashley J.; Scheer, Manfred; Liddle, Stephen T.

    2017-03-01

    Despite a major expansion of uranium-ligand multiple bond chemistry in recent years, analogous complexes involving other actinides (An) remain scarce. For thorium, under ambient conditions only a few multiple bonds to carbon, nitrogen, phosphorus and chalcogenides are reported, and none to arsenic are known; indeed only two complexes with thorium-arsenic single bonds have been structurally authenticated, reflecting the challenges of stabilizing polar linkages at the large thorium ion. Here, we report thorium parent-arsenide (ThAsH2), -arsinidiides (ThAs(H)K and ThAs(H)Th) and arsenido (ThAsTh) linkages stabilized by a bulky triamidoamine ligand. The ThAs(H)K and ThAsTh linkages exhibit polarized-covalent thorium-arsenic multiple bonding interactions, hitherto restricted to cryogenic matrix isolation experiments, and the AnAs(H)An and AnAsAn linkages reported here have no precedent in f-block chemistry. 7s, 6d and 5f orbital contributions to the Th-As bonds are suggested by quantum chemical calculations, and their compositions unexpectedly appear to be tensioned differently compared to phosphorus congeners.

  1. Triamidoamine thorium-arsenic complexes with parent arsenide, arsinidiide and arsenido structural motifs

    Science.gov (United States)

    Wildman, Elizabeth P.; Balázs, Gábor; Wooles, Ashley J.; Scheer, Manfred; Liddle, Stephen T.

    2017-01-01

    Despite a major expansion of uranium–ligand multiple bond chemistry in recent years, analogous complexes involving other actinides (An) remain scarce. For thorium, under ambient conditions only a few multiple bonds to carbon, nitrogen, phosphorus and chalcogenides are reported, and none to arsenic are known; indeed only two complexes with thorium–arsenic single bonds have been structurally authenticated, reflecting the challenges of stabilizing polar linkages at the large thorium ion. Here, we report thorium parent–arsenide (ThAsH2), –arsinidiides (ThAs(H)K and ThAs(H)Th) and arsenido (ThAsTh) linkages stabilized by a bulky triamidoamine ligand. The ThAs(H)K and ThAsTh linkages exhibit polarized-covalent thorium–arsenic multiple bonding interactions, hitherto restricted to cryogenic matrix isolation experiments, and the AnAs(H)An and AnAsAn linkages reported here have no precedent in f-block chemistry. 7s, 6d and 5f orbital contributions to the Th–As bonds are suggested by quantum chemical calculations, and their compositions unexpectedly appear to be tensioned differently compared to phosphorus congeners. PMID:28276437

  2. Low-Temperature Processed Ga-Doped ZnO Coatings from Colloidal Inks

    KAUST Repository

    Della Gaspera, Enrico

    2013-03-06

    We present a new colloidal synthesis of gallium-doped zinc oxide nanocrystals that are transparent in the visible and absorb in the near-infrared. Thermal decomposition of zinc stearate and gallium nitrate after hot injection of the precursors in a mixture of organic amines leads to nanocrystals with tunable properties according to gallium amount. Substitutional Ga3+ ions trigger a plasmonic resonance in the infrared region resulting from an increase in the free electrons concentration. These nanocrystals can be deposited by spin coating, drop casting, and spray coating resulting in homogeneous and high-quality thin films. The optical transmission of the Ga-ZnO nanoparticle assemblies in the visible is greater than 90%, and at the same time, the near-infrared absorption of the nanocrystals is maintained in the films as well. Several strategies to improve the films electrical and optical properties have been presented, such as UV treatments to remove the organic compounds responsible for the observed interparticle resistance and reducing atmosphere treatments on both colloidal solutions and thin films to increase the free carriers concentration, enhancing electrical conductivity and infrared absorption. The electrical resistance of the nanoparticle assemblies is about 30 kΩ/sq for the as-deposited, UV-exposed films, and it drops down to 300 Ω/sq after annealing in forming gas at 450 °C, comparable with state of the art tin-doped indium oxide coatings deposited from nanocrystal inks. © 2013 American Chemical Society.

  3. Zintl cluster chemistry in the alkali-metal-gallium systems

    Energy Technology Data Exchange (ETDEWEB)

    Henning, Robert [Iowa State Univ., Ames, IA (United States)

    1998-03-27

    Previous research into the alkali-metal-gallium systems has revealed a large variety of networked gallium deltahedra. The clusters are analogues to borane clusters and follow the same electronic requirements of 2n+2 skeletal electrons for closo-deltahedra. This work has focused on compounds that do not follow the typical electron counting rules. The first isolated gallium cluster was found in Cs8Ga11. The geometry of the Ga117- unit is not deltahedral but can be described as a penta-capped trigonal prism. The reduction of the charge from a closo-Ga1113- to Ga117- is believed to be the driving force of the distortion. The compound is paramagnetic because of an extra electron but incorporation of a halide atom into the structure captures the unpaired electron and forms a diamagnetic compound. A second isolated cluster has been found in Na10Ga10Ni where the tetra-capped trigonal prismatic gallium is centered by nickel. Stabilization of the cluster occurs through Ni-Ga bonding. A simple two-dimensional network occurs in the binary K2Ga3 Octahedra are connected through four waist atoms to form a layered structure with the potassium atoms sitting between the layers. Na30.5Ga60-xAgx is nonstoichiometric and needs only a small amount of silver to form (x ~ 2-6). The structure is composed of three different clusters which are interconnected to form a three-dimensional structure. The RbGa3-xAux system is also nonstoichiometric with a three-dimensional structure composed of Ga8 dodecahedra and four-bonded gallium atoms. Unlike Na30.5Ga60-xAgx, the RbGa3 binary is also stable. The binary is formally a Zintl phase but the ternary is not. Some chemistry in the alkali-metal-indium system also has been explored. A new potassium-indium binary

  4. Physical properties of Ga-doped ZnO thin films by spray pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Prasada Rao, T., E-mail: prasadview@gmail.co [Advanced Materials laboratory, Department of Physics, National Institute of Technology, Tiruchirappalli 620 015 (India); Santhosh Kumar, M.C., E-mail: santhoshmc@nitt.ed [Advanced Materials laboratory, Department of Physics, National Institute of Technology, Tiruchirappalli 620 015 (India)

    2010-09-17

    Research highlights: In this work, we report the structural, optical and electrical properties of the transparent conducting GZO thin films prepared by spray pyrolysis method. We sought optimum deposition conditions yielding GZO films with desired physical properties, specifically good crystalline quality microstructure, low resistivity and high transparency. The electrical conductivity and mobilities of GZO thin films are very good as compared with previous reported spray pyrolysed films. - Abstract: Gallium doped zinc oxide (GZO) thin films were prepared using the simple, flexible and cost-effective spray pyrolysis technique. The physical properties of the films were studied as a function of increasing gallium dopant concentration from 1 to 9 at.%. The films were characterized by various methods to understand their structural, morphological, optical and electrical properties. The X-ray diffraction analysis revealed that the films were polycrystalline in nature having a hexagonal wurtzite type crystal structure with a preferred grain orientation in the (0 0 2) direction. Scanning electron microscopy (SEM) measurements reveal that the surface morphology of the films changes continuously with a decrease in the grain size due to Ga doping. All the films showed nearly 90% of transparency in the entire visible region. A blue shift of the optical band gap was observed with an increase in Ga doping. Room temperature photoluminescence (PL) measurement of the deposited films indicates incorporation of Ga in ZnO lattice. At 3 at.% Ga doping, the film has lowest resistivity of 6.8 x 10{sup -3} cm while the carrier concentration is highest.

  5. Transition from three-dimensional anisotropic spin excitations to two-dimensional spin excitations by electron doping the FeAs-based BaFe1.96Ni0.04As2 superconductor.

    Science.gov (United States)

    Harriger, Leland W; Schneidewind, Astrid; Li, Shiliang; Zhao, Jun; Li, Zhengcai; Lu, Wei; Dong, Xiaoli; Zhou, Fang; Zhao, Zhongxian; Hu, Jiangping; Dai, Pengcheng

    2009-08-21

    We use neutron scattering to study the effect of electron doping on the structural or magnetic order in BaFe2As2. In the undoped state, BaFe2As2 exhibits simultaneous structural and magnetic phase transitions below 143 K. Upon electron doping to form BaFe1.96Ni0.04As2, the system first displays the lattice distortion near approximately 97 K, and then orders antiferromagnetically at 91 K before developing weak superconductivity below approximately 15 K. The effect of electron doping is to reduce the c-axis exchange coupling in BaFe2As2 and induce quasi-two-dimensional (2D) spin excitations. These results suggest that the transition from 3D spin waves to quasi-2D spin excitations by electron doping is important for the separated structural and magnetic phase transitions in iron arsenides.

  6. Gallium-containing polymer brush film as efficient supported Lewis acid catalyst in a glass microreactor

    NARCIS (Netherlands)

    Munirathinam, Rajesh; Ricardi, Roberto; Egberink, Richard J.M.; Huskens, Jurriaan; Holtkamp, Michael; Wormeester, Herbert; Karst, U.; Verboom, Willem

    2013-01-01

    Polystyrene sulfonate polymer brushes, grown on the interior of the microchannels in a microreactor, have been used for the anchoring of gallium as a Lewis acid catalyst. Initially, gallium-containing polymer brushes were grown on a flat silicon oxide surface and were characterized by FTIR,

  7. Gallium nitrate: effects on cartilage during limb regeneration in the axolotl, Ambystoma mexicanum.

    Science.gov (United States)

    Tassava, Roy A; Mendenhall, Luciara; Apseloff, Glen; Gerber, Nicholas

    2002-09-01

    Gallium nitrate, a drug shown to have efficacy in Paget's disease of bone, hypercalcemia of malignancy, and a variety of experimental autoimmune diseases, also inhibits the growth of some types of cancer. We examined dose and timing of administration of gallium nitrate on limb regeneration in the Mexican axolotl, Ambystoma mexicanum. Administered by intraperitoneal injection, gallium nitrate inhibited limb regeneration in a dose-dependent manner. Gallium nitrate initially suppressed epithelial wound healing and subsequently distorted both anterior-posterior and proximo-distal chondrogenic patterns. Gallium nitrate given at three days after amputation severely inhibited regeneration at high doses (6.25 mg/axolotl) and altered the normal patterning of the regenerates at low doses (3.75 mg/axolotl). Administration of 6.25 mg of gallium nitrate at four or 14 days prior to amputation also inhibited regeneration. In amputated limbs of gallium-treated axolotls, the chondrocytes were lost from inside the radius/ulna. Limbs that regenerated after gallium treatment was terminated showed blastema formation preferentially over the ulna. New cartilage of the regenerate often attached to the sides of the existing radius/ulna proximally into the stump and less so to the distal cut ends. J. Exp. Zool. 293:384-394, 2002.

  8. Failure of Gallium-67 scintigraphy to identify reliably noninfectious interstitial nephritis: concise communication

    Energy Technology Data Exchange (ETDEWEB)

    Graham, G.D.; Lundy, M.M.; Moreno, A.J.

    1983-07-01

    Gallium-67 scintigraphy has been reported to be useful in the diagnosis of noninfectious interstitial nephritis. We studied 12 patients with Ga-67 citrate that were diagnosed as having noninfectious interstitial nephritis on renal biopsy. Only seven of the twelve patients with interstitial nephritis on biopsy were scan-positive. Gallium-67 scintigraphy may not reliably identify noninfectious interstitial nephritis.

  9. Dot-array implantation for patterned doping of semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Wanzenboeck, H.D. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria)]. E-mail: heinz.wanzenboeck@tuwien.ac.at; Ostermaier, C. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria); Gruen, A. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria); Eichinger, B. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria); Karner, M. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria); Bertagnolli, E. [Institute f. Solid State Electronics, Vienna University of Technology, Floragasse 7, A-1040 Vienna (Austria)

    2006-01-15

    Novel ion beam processing for microelectronic applications has been performed by doping silicon with a focused ion beam tool. A Ga{sup +} ion beam with a energy between 10 and 50 keV was used for p-doping of Si. The ion beam could be focused to an effective beam diameter in the sub-micron range with the smallest focus own below 10 nm. In contrast to conventional implantation with a broad ion beam where the doped area is assigned by a hardmask the implantation was achieved by scanning a focused ion beam over the designated implantation area. With this approach not only the hardmask becomes obsolete because of the electronic beam guidance. Moreover, different doses may be implanted on the same wafer. An additional feature is the inhomogeneous implantation in a pixel-array, where the distance between exposed pixels can be deliberately varied. Even single spots can be independently doped with the focused gallium beam. Due to lateral scattering of ions in the semiconductor the circular implantation area is larger than the beam diameter. With a variation of the pixel spacing we could intentionally obtain either a overlap or a separation of implantation spots. With a four-point method we have investigated the conductivity of the dot-array implanted area. The conductivity of the p-doped region could be deliberately scaled by varying the pixel spacing, the implantation dose and the ion energy. The effective implantation diameter of a single pixel could be determined. This modified implantation approach was also used to fabricate functional p-channel MOSFET's. The Ga implantation with a focused ion beam was used for p-doping of source and drain regions of the transistor device. The utilization of this dot-array implantation with a FIB for semiconductor circuitry demonstrates the potential application of this approach. With the laterally inhomogeneous implantation dot-arrays of doped zones in the nanometer range could be fabricated.

  10. Superconductivity by transition metal doping in Ca10(Fe1-xMxAs)10(Pt3As8) (M = Co, Ni, Cu)

    Science.gov (United States)

    Stürzer, Tobias; Kessler, Fabian; Johrendt, Dirk

    2014-11-01

    We report the successful substitution of cobalt, nickel and copper for iron in the 1038-phase parent compound ? yielding ?, ? and ?), respectively. Superconductivity is induced in Co and Ni doped compounds reaching critical temperatures up to 15 K, similar to known Pt substituted ?), whereas no superconductivity was detected in ?. The obtained ? phase diagrams are very similar to those of other iron arsenide superconductors indicating rather universal behaviour despite the more complex structures of the 1038-type compounds, where the physics is primarily determined by the FeAs layer.

  11. Activity of gallium on prevention of fatal cage-layer osteoporosis.

    Science.gov (United States)

    Chen, Xiuxia; Wang, Chao

    2009-12-01

    The prevention of fatal cage-layer osteoporosis of gallium was studied in this paper. One-day-old hens were fed up to 68 weeks on a control diet and diets containing gallium. Plasma variables were measured during lay. End-of-lay trabecular and medullary bone volumes in the proximal tarsometatarsus and free thoracic vertebra were measured by histomorphometry. Medullary and trabecular bone volumes were increased significantly by supplementation with gallium. The experiment confirmed that dietary gallium supplementation was an effective way to enhance the egg production and reduce mortality percentage. The beneficial effects of gallium supplementation over the lifetime of the hens were attributable mainly to improved cage-layer osteoporosis.

  12. Electron correlations in Mn(x)Ga(1-x)A(s)as seen by resonant electron spectroscopy and dynamical mean field theory.

    Science.gov (United States)

    Di Marco, I; Thunström, P; Katsnelson, M I; Sadowski, J; Karlsson, K; Lebègue, S; Kanski, J; Eriksson, O

    2013-01-01

    After two decades since the discovery of ferromagnetism in manganese-doped gallium arsenide, its origin is still debated, and many doubts are related to the electronic structure. Here we report an experimental and theoretical study of the valence electron spectrum of manganese-doped gallium arsenide. The experimental data are obtained through the differences between off- and on-resonance photo emission data. The theoretical spectrum is calculated by means of a combination of density-functional theory in the local density approximation and dynamical mean field theory, using exact diagonalization as impurity solver. Theory is found to accurately reproduce measured data and illustrates the importance of correlation effects. Our results demonstrate that the manganese states extend over a broad range of energy, including the top of the valence band, and that no impurity band splits-off from the valence band edge, whereas the induced holes seem located primarily around the manganese impurity.

  13. Gallium nitrate regulates rat osteoblast expression of osteocalcin protein and mRNA levels.

    Science.gov (United States)

    Guidon, P T; Salvatori, R; Bockman, R S

    1993-01-01

    Gallium nitrate, a group IIIa metal salt, has been found to be clinically effective for the treatment of accelerated bone resorption in cancer-related hypercalcemia and Paget's disease. Here we report the effects of gallium nitrate on osteocalcin mRNA and protein levels on the rat osteoblast-like cell line ROS 17/2.8. Gallium nitrate reduced both constitutive and vitamin D3-stimulated osteocalcin protein levels in culture medium by one-half and osteocalcin mRNA levels to one-third to one-tenth of control. Gallium nitrate also inhibited vitamin D3 stimulation of osteocalcin and osteopontin mRNA levels but did not affect constitutive osteopontin mRNA levels. Among several different metals examined, gallium was unique in its ability to reduce osteocalcin mRNA levels without decreasing levels of other mRNAs synthesized by ROS 17/2.8 cells. The effects of gallium nitrate on osteocalcin mRNA and protein synthesis mimic those seen when ROS 17/2.8 cells are exposed to transforming growth factor beta 1 (TGF beta 1); however, TGF-beta 1 was not detected in gallium nitrate-treated ROS 17/2.8 cell media. Use of the RNA polymerase II inhibitor 5,6-dichloro-1-beta-D-ribofuranosylbenzimidazole demonstrated that gallium nitrate did not alter the stability of osteocalcin mRNA. Transient transfection assays using the rat osteocalcin promoter linked to the bacterial reporter gene chloramphenicol acetyltransferase indicated that gallium nitrate blocked reporter gene expression stimulated by the osteocalcin promoter. This is the first reported effect of gallium nitrate on isolated osteoblast cells.

  14. Rare Earth Doped Gallium Gadolinium Orthogallate Films Prepared by Pulsed Laser Deposition

    Energy Technology Data Exchange (ETDEWEB)

    Lancok, J [Institute of Physics, Academy of Sciences of the Czech Republic, Na Slovance 2, 182 21 Prague 8, Czech Republic (Czech Republic); Novotny, M [Institute of Physics, Academy of Sciences of the Czech Republic, Na Slovance 2, 182 21 Prague 8, Czech Republic (Czech Republic); Garapon, C [LPCML, UMR 5620 CNRS-Universite Claude Bernard Lyon-I, 10 rue Andre Marie Ampere, 69622 Villeurbanne Cedex (France); JelInek, M [Institute of Physics, Academy of Sciences of the Czech Republic, Na Slovance 2, 182 21 Prague 8, Czech Republic (Czech Republic)

    2007-04-15

    The decomposition of Gd{sub 3}Ga{sub 5}O{sub 12} single crystal target induced by a KrF excimer laser pulse during the deposition process was observed. This phenomenon was studied ex situ by EDX analyse of ablated target and in situ by Optical Emission Spectroscopy of the laser plasma. The decomposition process depends mainly on the absorption coefficient of the target on the corresponding laser wavelength and oxygen partial pressure in the deposition chamber during laser ablation. Taking into account the differences between absorption coefficients of Pr:Gd{sub 3}Ga{sub 5}O{sub 12} and Yb:Gd{sub 3}Ga{sub 5}O{sub 12} targets the Pr:GdGaO{sub 3} and Yb:GdGaO{sub 3} thin films were successfully fabricated at different oxygen pressures of 1 Pa and 2.5 Pa, respectively. The structural properties of the fabricated films were studied by RBS and XRD.

  15. A Theoretical Study of Lithium-Doped Gallium Clusters by Density Functional Theory

    Science.gov (United States)

    Şentürk, Şükrü; Ekincioğlu, Yavuz

    2012-05-01

    The geometrical structures, stabilities, and electronic properties of GanLi (n = 1 - 13) clusters were investigated within the density functional theory (DFT). The impurity lithium atom enhances the stability of GanLi (n = 1 - 13) clusters, especially GanLi (n = 9 - 13) compared to Gan(n = 9 - 14), that is at either apex position or side position. The dissociation energy, second-order energy differences, and the energy gaps between highest occupied and lowest unoccupied molecular orbital (HOMO-LUMO) indicate that the Ga7Li, Ga9Li, and Ga11Li clusters are more stable within the studied cluster range. Moreover, the variation of the average bond length of Ga-Li is due to the surface effect, and the binding strength increases resulting from the increase of charge amount.

  16. Effects of erbium‑and chromium‑doped yttrium scandium gallium ...

    African Journals Online (AJOL)

    2014-08-21

    Aug 21, 2014 ... tissues and might cause crater‑like defects on dental hard tissues during ... were polished with aluminum‑oxide‑coated disks (Sof‑Lex;. 3M ESPE ..... Er: YAG laser irradiation on the scanning electron microscopic structure and.

  17. SPECTROSCOPIC PROPERTIES OF Ca-SUBSTITUTED GADOLINIUM GALLIUM GARNET DOPED WITH V4+

    OpenAIRE

    Suchocki, A.; BRENIER, A.; PEDRINI, C.; BOULON, G.

    1991-01-01

    The results of absorption, luminescence and luminescence excitation, fluorescence decay kinetics and photoconductivity measurements of Gd3Ga5O12 : V4+, Ca2+ (0.5% mol.) garnet are reported in detail. A strong quenching of the luminescence of V4+ ions in octahedral sites by the energy transfer to V4+ ions in tetrahedral sites is observed. Broad, strong bands observed in absorption and luminescence excitation spectra of octahedral V4+ ions in the ultraviolet region are assigned to small polaron...

  18. The Effects of Rare Earth Doping on Gallium Nitride Thin Films

    Science.gov (United States)

    2011-09-01

    capture in a solid state device,” Journal of Physics D: Applied Physics, vol. 43, p. 075502, 2010. [28] D. S. McGregor, M. F. Ohmes , R. E. Ortiz, A. S...1044, 1964. [5] M. Cardona and L. Ley , Photoemission in Solids: General Principles. Springer- Verlag New York, 1978. [6] C. Cohen-Tannoudji, B. Diu...A, vol. 50, no. 6, pp. 449–450, 1975. [46] L. Ley , R. A. Pollak, F. R. McFeely, S. P. Kowalczyk, and D. A. Shirley, “Total valence-band densities of

  19. Pressure-induced luminescence of cerium-doped gadolinium gallium garnet crystal

    Science.gov (United States)

    Kaminska, A.; Duzynska, A.; Berkowski, M.; Trushkin, S.; Suchocki, A.

    2012-04-01

    Studies of the spectroscopic properties of Ce3+ dopant in bulk Gd3Ga5O12:Ce crystal under pressure are presented. In spite of strong intershell 4f→5d absorption bands at ambient pressure, the cerium luminescence in Gd3Ga5O12 is entirely quenched even at low temperature. It has been shown that applying pressure allows for recovery of the 5d→4f radiative transitions. Further increase of pressure improves the emission efficiency. This effect is analyzed in terms of two possible phenomena: (i) by pressure-induced electronic crossover of the excited 5d energy level of the Ce3+ with the conduction band bottom of the host crystal, and (ii) by decrease of electron-lattice coupling with increasing pressure, resulting in reduction of the Stokes shift and nonradiative transitions between the low vibrational levels of the 5d state and high vibrational levels of the ground 4f state. The results of high-pressure absorption and luminescence measurements point out that the ambient-pressure luminescence quenching is caused by the donor-like charge transfer processes due to the resonant location of the Ce3+ 5d electronic levels with respect to the host conduction band. In such a situation, the ionization of Ce3+ to Ce4+ occurs, accompanied by large lattice relaxation, which enables the nonradiative recombination to the Ce 4f state. The pressure-induced approach of the conduction-band bottom of the host crystal by the excited 5d energy level of the Ce3+ results in mixing between conduction band states and the 5d state, and the broadband luminescence from this mixed state is observed at pressures from 30 up to about 60 kbar. Then, for pressures exceeding 60 kbar, this luminescence is replaced by the classic Ce3+5d→4f transitions. Using a simple anticrossing model and configuration coordinate model in the appropriate pressure range, quantitative description of the system has been carried out, and the pressure-induced decrease of electron-lattice coupling has been shown.

  20. Spectroscopy of gadolinium gallium garnet doped with cerium under high hydrostatic pressure

    OpenAIRE

    2012-01-01

    Studies of the spectroscopic properties of Ce3+ dopant in bulk Gd3Ga5O12:Ce crystal under pressure are presented. In spite of strong inter-shell 4f ® 5d absorption bands at ambient pressure the cerium luminescence in Gd3Ga5O12 is entirely quenched even at low temperature. It has been shown that applying pressure allows for recovering the 5d ® 4f radiative transitions. Further increase of pressure improves the emission efficiency. This effect is analyzed in terms of two possible phenomen...

  1. Control of Surface Attack by Gallium Alloys in Electrical Contacts.

    Science.gov (United States)

    1986-03-28

    and atmospheric control but does not allow visual observation of the contact brushes. This machine is a small homopolar motor built from mild steel...collectors,gallium, homopolar devices,liquid metals,~- is. ABSTRACT ICNI.. .. w 41N"w -~dv.mp.d Wrllt by Itabata" * Electrical contact between a copp’er...32 5 Test rig with felt metal brushes 32 6 Homopolar test apparatus 33 7 Rewetting of alloy track 33 8 Alloy track after running with finger 34 brushes

  2. Phase Coexistence in Gallium Nanoparticles Controlled by Electron Excitation

    Science.gov (United States)

    Pochon, S.; MacDonald, K. F.; Knize, R. J.; Zheludev, N. I.

    2004-04-01

    In gallium nanoparticles 100nm in diameter grown on the tip of an optical fiber from an atomic beam we observed equilibrium coexistence of γ, β, and liquid structural phases that can be controlled by e-beam excitation in a highly reversible and reproducible fashion. With 2keV electrons only 1pJ of excitation energy per nanoparticle is needed to exercise control, with the equilibrium phase achieved in less than a few tenths of a microsecond. The transformations between coexisting phases are accompanied by a continuous change in the nanoparticle film's reflectivity.

  3. Gallium uptake in tryptophan-related pulmonary disease

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S.M.; Park, C.H.; Intenzo, C.M.; Patel, R. (Thomas Jefferson Univ. Hospital, Philadelphia, PA (USA))

    1991-02-01

    We describe a patient who developed fever, fatigue, muscle weakness, dyspnea, skin rash, and eosinophilia after taking high doses of tryptophan for insomnia for two years. A gallium-67 scan revealed diffuse increased uptake in the lung and no abnormal uptake in the muscular distribution. Bronchoscopy and biopsy confirmed inflammatory reactions with infiltration by eosinophils, mast cells, and lymphocytes. CT scan showed an interstitial alveolar pattern without fibrosis. EMG demonstrated diffuse myopathy. Muscle biopsy from the right thigh showed an inflammatory myositis with eosinophilic and lymphocytic infiltrations.

  4. Self-diffusion in liquid gallium and hard sphere model

    Directory of Open Access Journals (Sweden)

    Blagoveshchenskii Nikolay

    2015-01-01

    Full Text Available Incoherent and coherent components of quasielastic neutron scattering have been studied in the temperature range of T = 313 K – 793 K aiming to explore the applicability limits of the hard-sphere approach for the microscopic dynamics of liquid gallium, which is usually considered as a non-hard-sphere system. It was found that the non-hard-sphere effects come into play at the distances shorter than the average interatomic distance. The longer range diffusive dynamics of liquid Ga is dominated by the repulsive forces between the atoms.

  5. Visible light metasurfaces based on gallium nitride high contrast gratings

    Science.gov (United States)

    Wang, Zhenhai; He, Shumin; Liu, Qifa; Wang, Wei

    2016-05-01

    We propose visible-light metasurfaces (VLMs) capable of serving as lens and beam deflecting element based on gallium nitride (GaN) high contrast gratings (HCGs). By precisely manipulating the wavefront of the transmitted light, we theoretically demonstrate an HCG focusing lens with transmissivity of 86.3%, and a VLM with beam deflection angle of 6.09° and transmissivity as high as 91.4%. The proposed all-dielectric metasurfaces are promising for GaN-based visible light-emitting diodes (LEDs), which would be robust and versatile for controlling the output light propagation and polarization, as well as enhancing the extraction efficiency of the LEDs.

  6. Fabrication of hexagonal gallium nitride films on silicon (111) substrates

    Institute of Scientific and Technical Information of China (English)

    YANG Li; XUE Chengshan; WANG Cuimei; LI Huaixiang; REN Yuwen

    2003-01-01

    Hexagonal gallium nitride films were successfully fabricated through ammoniating Ga2O3 films deposited on silicon (111 ) substrates by electrophoresis. The structure, composition, and surface morphology of the formed films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM),and transmission electron microscopy (TEM). The measurement results reveal that the polycrystalline GaN films with hexagonal wurtzite structure were successfully grown on the silicon (111) substrates. Preliminary results suggest that varying the ammoniating temperature has obvious effect on the quality of the GaN films formed with this method.

  7. Lasing action in gallium nitride quasicrystal nanorod arrays.

    Science.gov (United States)

    Chang, Shih-Pang; Sou, Kuok-Pan; Chen, Chieh-Han; Cheng, Yuh-Jen; Huang, Ji-Kai; Lin, Chung-Hsiang; Kuo, Hao-Chung; Chang, Chun-Yen; Hsieh, Wen-Feng

    2012-05-21

    We report the observation of lasing action from an optically pumped gallium nitride quasicrystal nanorod arrays. The nanorods were fabricated from a GaN substrate by patterned etching, followed by epitaxial regrowth. The nanorods were arranged in a 12-fold symmetric quasicrystal pattern. The regrowth grew hexagonal crystalline facets and core-shell multiple quantum wells (MQWs) on nanorods. Under optical pumping, multiple lasing peaks resembling random lasing were observed. The lasing was identified to be from the emission of MQWs on the nanorod sidewalls. The resonant spectrum and mode field of the 12-fold symmetric photonic quasicrystal nanorod arrays is discussed.

  8. Gallium nitride electrodes for membrane-based electrochemical biosensors.

    Science.gov (United States)

    Schubert, T; Steinhoff, G; von Ribbeck, H-G; Stutzmannn, M; Eickhoff, M; Tanaka, M

    2009-10-01

    We report on the deposition of planar lipid bilayers (supported membranes) on gallium nitride (GaN) electrodes for potential applications as membrane-based biosensors. The kinetics of the lipid membrane formation upon vesicle fusion were monitored by simultaneous measurements of resistance and capacitance of the membrane using AC impedance spectroscopy in the frequency range between 50 mHz and 50 kHz. We could identify a two-step process of membrane spreading and self-healing. Despite its relatively low resistance, the membrane can be modeled by a parallel combination of an ideal resistor and capacitor, indicating that the membrane efficiently blocks the diffusion of ions.

  9. A review of magnetostrictive iron-gallium alloys

    Science.gov (United States)

    Atulasimha, Jayasimha; Flatau, Alison B.

    2011-04-01

    A unique combination of low hysteresis, moderate magnetostriction at low magnetic fields, good tensile strength, machinability and recent progress in commercially viable methods of processing iron-gallium alloys make them well poised for actuator and sensing applications. This review starts with a brief historical note on the early developments of magnetostrictive materials and moves to the recent work on FeGa alloys and their useful properties. This is followed by sections addressing the challenges specific to the characterization and processing of FeGa alloys and the state of the art in modeling their actuation and sensing behavior.

  10. Recent progress in the determination of gallium, indium, and thallium

    Institute of Scientific and Technical Information of China (English)

    GAO Jinzhang

    2005-01-01

    This mini-review covers the literatures of the determination of gallium, indium, and thallium by instrumental analysis with computer-assisted searching over the period of 1994 to 2003. Some papers appearing in the early of 2004 are also included. Because the rapid progress in the instrument has been made, these new papers are prioritized in selection in the similar papers. The contents are considered to be separation and preconcentration, spectrophotometry, spectrofluorimetry, electroanalyses, atomic absorption spectrometry, inductively coupled plasma-atomic emission spectrometry, inductively coupled plasma-mass spectrometry and so forth.

  11. Infrared spectroscopy of rare-earth-doped CaFe2As2

    Science.gov (United States)

    Xing, Zhen; Huffman, T. J.; Xu, Peng; Qazilbash, M. M.; Saha, S. R.; Drye, Tyler; Paglione, J.

    2014-03-01

    Recently, rare-earth doping in CaFe2As2 has been used to tune its electronic, magnetic, and structural properties. The substitution of rare-earth ions at the alkaline-earth sites leads to the suppression of the spin-density wave (SDW) phase transition in CaFe2As2. For example, Pr substitution results in a paramagnetic metal in the tetragonal phase that is susceptible to a low temperature structural transition to a collapsed tetragonal phase. However, La-doped CaFe2As2 remains in the uncollapsed tetragonal structure down to the lowest measured temperatures. Both the uncollapsed and collapsed tetragonal structures exhibit superconductivity with maximum Tc reaching 47 K, the highest observed in inter-metallics albeit with a small superconducting volume fraction. In this work, we perform ab-plane infrared spectroscopy of rare-earth-doped CaFe2As2 at different cryogenic temperatures. Our aim is to ascertain the contributions of electron doping and chemical pressure to the charge and lattice dynamics of this iron-arsenide system.

  12. Electron-phonon relaxation and excited electron distribution in gallium nitride

    Energy Technology Data Exchange (ETDEWEB)

    Zhukov, V. P. [Institute of Solid State Chemistry, Urals Branch of the Russian Academy of Sciences, Pervomayskaya st. 91, Yekaterinburg (Russian Federation); Donostia International Physics Center (DIPC), P. Manuel de Lardizabal 4, 20018 San Sebastian (Spain); Tyuterev, V. G., E-mail: valtyut00@mail.ru [Donostia International Physics Center (DIPC), P. Manuel de Lardizabal 4, 20018 San Sebastian (Spain); Tomsk State Pedagogical University, Kievskaya st. 60, Tomsk (Russian Federation); Tomsk State University, Lenin st. 36, Tomsk (Russian Federation); Chulkov, E. V. [Donostia International Physics Center (DIPC), P. Manuel de Lardizabal 4, 20018 San Sebastian (Spain); Tomsk State University, Lenin st. 36, Tomsk (Russian Federation); Departamento de Fisica de Materiales, Facultad de Ciencias Qumicas, UPV/EHU and Centro de Fisica de Materiales CFM-MPC and Centro Mixto CSIC-UPV/EHU, Apdo. 1072, 20080 San Sebastian (Spain); Echenique, P. M. [Donostia International Physics Center (DIPC), P. Manuel de Lardizabal 4, 20018 San Sebastian (Spain); Departamento de Fisica de Materiales, Facultad de Ciencias Qumicas, UPV/EHU and Centro de Fisica de Materiales CFM-MPC and Centro Mixto CSIC-UPV/EHU, Apdo. 1072, 20080 San Sebastian (Spain)

    2016-08-28

    We develop a theory of energy relaxation in semiconductors and insulators highly excited by the long-acting external irradiation. We derive the equation for the non-equilibrium distribution function of excited electrons. The solution for this function breaks up into the sum of two contributions. The low-energy contribution is concentrated in a narrow range near the bottom of the conduction band. It has the typical form of a Fermi distribution with an effective temperature and chemical potential. The effective temperature and chemical potential in this low-energy term are determined by the intensity of carriers' generation, the speed of electron-phonon relaxation, rates of inter-band recombination, and electron capture on the defects. In addition, there is a substantial high-energy correction. This high-energy “tail” largely covers the conduction band. The shape of the high-energy “tail” strongly depends on the rate of electron-phonon relaxation but does not depend on the rates of recombination and trapping. We apply the theory to the calculation of a non-equilibrium distribution of electrons in an irradiated GaN. Probabilities of optical excitations from the valence to conduction band and electron-phonon coupling probabilities in GaN were calculated by the density functional perturbation theory. Our calculation of both parts of distribution function in gallium nitride shows that when the speed of the electron-phonon scattering is comparable with the rate of recombination and trapping then the contribution of the non-Fermi “tail” is comparable with that of the low-energy Fermi-like component. So the high-energy contribution can essentially affect the charge transport in the irradiated and highly doped semiconductors.

  13. Phase diagram of (Li(1-x)Fe(x))OHFeSe: a bridge between iron selenide and arsenide superconductors.

    Science.gov (United States)

    Dong, Xiaoli; Zhou, Huaxue; Yang, Huaixin; Yuan, Jie; Jin, Kui; Zhou, Fang; Yuan, Dongna; Wei, Linlin; Li, Jianqi; Wang, Xinqiang; Zhang, Guangming; Zhao, Zhongxian

    2015-01-14

    Previous experimental results have shown important differences between iron selenide and arsenide superconductors which seem to suggest that the high-temperature superconductivity in these two subgroups of iron-based families may arise from different electronic ground states. Here we report the complete phase diagram of a newly synthesized superconducting (SC) system, (Li1-xFex)OHFeSe, with a structure similar to that of FeAs-based superconductors. In the non-SC samples, an antiferromagnetic (AFM) spin-density-wave (SDW) transition occurs at ∼127 K. This is the first example to demonstrate such an SDW phase in an FeSe-based superconductor system. Transmission electron microscopy shows that a well-known √5×√5 iron vacancy ordered state, resulting in an AFM order at ∼500 K in AyFe2-xSe2 (A = metal ions) superconductor systems, is absent in both non-SC and SC samples, but a unique superstructure with a modulation wave vector q = (1)/2(1,1,0), identical to that seen in the SC phase of KyFe2-xSe2, is dominant in the optimal SC sample (with an SC transition temperature Tc = 40 K). Hence, we conclude that the high-Tc superconductivity in (Li1-xFex)OHFeSe stems from the similarly weak AFM fluctuations as FeAs-based superconductors, suggesting a universal physical picture for both iron selenide and arsenide superconductors.

  14. Gallium-67 uptake by the thyroid associated with progressive systemic sclerosis

    Energy Technology Data Exchange (ETDEWEB)

    Sjoberg, R.J.; Blue, P.W.; Kidd, G.S.

    1989-01-01

    Although thyroidal uptake of gallium-67 has been described in several thyroid disorders, gallium-67 scanning is not commonly used in the evaluation of thyroid disease. Thyroidal gallium-67 uptake has been reported to occur frequently with subacute thyroiditis, anaplastic thyroid carcinoma, and thyroid lymphoma, and occasionally with Hashimoto's thyroiditis and follicular thyroid carcinoma. A patient is described with progressive systemic sclerosis who, while being scanned for possible active pulmonary involvement, was found incidentally to have abnormal gallium-67 uptake only in the thyroid gland. Fine needle aspiration cytology of the thyroid revealed Hashimoto's thyroiditis. Although Hashimoto's thyroiditis occurs with increased frequency in patients with progressive systemic sclerosis, thyroidal uptake of gallium-67 associated with progressive systemic sclerosis has not, to our knowledge, been previously described. Since aggressive thyroid malignancies frequently are imaged by gallium-67 scintigraphy, fine needle aspiration cytology of the thyroid often is essential in the evaluation of thyroidal gallium-67 uptake.

  15. Gallium-67 scanning in the staging of cryptogenetic fibrosing alveolitis and hypersensitivity pneumonitis

    Energy Technology Data Exchange (ETDEWEB)

    Vanderstappen, M.; Mornex, J.F.; Lahneche, B.; Chauvot, P.; Bouvier, J.F.; Wiesendanger, T.; Pages, J.; Webert, P.; Cordier, J.F.; Brune, J.

    1988-01-01

    Gallium-67 citrate is known to localize within inflammatory sites. Gallium-67 scanning is used for the evaluation of lung inflammation (i.e. alveolitis) during interstitial lung diseases. We investigated 27 patients with cryptogenetic fibrosing alveolitis (n=17) and hypersensitivity pneumonitis (n=10) using gallium-67 lung scanning and lung function tests (forced vital capacity, diffusing capacity, resting and exercise blood gases). Investigations were performed before and after one year of methylprednisolone treatment. None of eight healthy volunteers had any abnormal gallium-67 uptake. In all patients with cryptogenetic fibrosing alveolitis and initial abnormal gallium-67 uptake was observed (mean fixation index: 163+-18). In addition, analysis of lung function tests a year after initial evaluation showed that unchanged or improving patients presented initially with a lower gallium-67 index than patients with evidence of deterioration (163.9+-23.7 vs 251.0+-23.3.; p<0.01). Similarly, among patients with hypersensitivity pneumonitis the index was lower in unchanged or improving patients than in those with deterioration (74.0+-22 vs 226.7+-4.9; p<0.05). Thus gallium-67 scanning is useful in the management of cryptogenetic fibrosing alveolitis and hypersensitivity pneumonitis.

  16. Hydrogen Production from Water by Photolysis, Sonolysis and Sonophotolysis with Solid Solutions of Rare Earth, Gallium and Indium Oxides as Heterogeneous Catalysts

    Directory of Open Access Journals (Sweden)

    Marta Penconi

    2015-07-01

    Full Text Available In this work, we present the hydrogen production by photolysis, sonolysis and sonophotolysis of water in the presence of newly synthesized solid solutions of rare earth, gallium and indium oxides playing as catalysts. From the experiments of photolysis, we found that the best photocatalyst is the solid solution Y0.8Ga0.2InO3 doped by sulphur atoms. In experiments of sonolysis, we optimized the rate of hydrogen production by changing the amount of water, adding ethanol and tuning the power of our piezoelectric transducer. Finally, we performed sonolysis and sonophotolysis experiments in the presence of S:Y0.8Ga0.2InO3 finding a promising synergistic effect of UV-visible electromagnetic waves and 38 kHz ultrasound waves in producing H2.

  17. Gallium nanoparticles colloids synthesis for UV bio-optical sensors

    Science.gov (United States)

    Nucciarelli, Flavio; Bravo, Iria; Vázquez, Luis; Lorenzo, Encarnación; Pau, Jose Luis

    2017-05-01

    A new method for the synthesis of colloidal gallium nanoparticles (Ga NPs) based on the thermal evaporation of Ga on an expendable aluminum zinc oxide (AZO) layer is presented here. The growth of AZO layers was investigated on different substrates at room temperature and 300 °C. By means of physical evaporation process, nanoparticles were deposited with a distribution ranging from 10 nm to 80 nm in diameter. A study of their endurance in acidic environment was carried out in order to assure the NPs shape and size stability during the etching process. Smaller particles start to disappear between 1h and 2h immersion time in a pH=1 solution, while bigger particles reduce their dimension. The NPs were dispersed in tetrahydrofuran (THF) organic solvent and optically characterized, showing strong UV absorption with a band centered at 280 nm. The colloids size distribution of as-evaporated samples was compared with the distribution obtained in droplets of the solution after drop-casting. By Dipole Discrete Approximation simulations, a close relationship between the UV absorption and the NPs with diameter smaller than 40 nm was found. Because of the gallium oxide (Ga1-xOx) outer shell that surrounds the Ga NPs, an enhancement of their hydrophobicity occurs. Hence, the low agglomeration state between NPs in tetrahydrofuran allows to obtain narrow absorption band in the optical spectrum.

  18. Adsorptive stripping voltammetric determination of chromium in gallium.

    Science.gov (United States)

    Palrecha, M M; Mathur, P K

    1997-12-19

    The electroanalytical chemistry of trace metals has progressed strongly with the development of cathodic stripping voltammetry (CSV) preceded by adsorption collection of organic metal complexes. A sensitive method for the determination of trace amount of chromium in gallium is described. Gallium is dissolved in sodium hydroxide containing hydrogen peroxide. The method is based on the catalytic activity of nitrate ions on the reduction of Cr(III)TTHA (triethylene tetramine-N,N,N',N'',N''',N'''-hexaacetic acid) complex. The sensitivity of this method is further improved by adsorption preconcentration of Cr(III)TTHA complex at a hanging mercury drop electrode (HMDE). The Cr(III) formed at the electrode surface by the reduction of Cr(VI), which is present in the bulk solution, is immediately complexed by TTHA. The adsorbed complex is then reduced at a peak potential of - 1.26 V, and the peak height of Cr(III) reduction is measured. The determination limit was restricted by the amount of chromium present in the reagent blank solution. The method is suitable for the determination of chromium at level as low as 0.2 mug g(-1) (with about 50 mg of sample) and a relative standard deviation of 15%.

  19. Low temperature solid-state synthesis of nanocrystalline gallium nitride

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Liangbiao, E-mail: wlb6641@163.com [Hefei National Laboratory for Physical Science at Microscale and Department of Chemistry, University of Science and Technology of China, Hefei, Anhui 230026 (China); Shi, Liang; Li, Qianwen; Si, Lulu; Zhu, Yongchun; Qian, Yitai [Hefei National Laboratory for Physical Science at Microscale and Department of Chemistry, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2012-11-15

    Graphical abstract: Display Omitted Highlights: ► GaN nanocrystalline was prepared via a solid-state reacion at relatively low temperature. ► The sizes and crystallinities of the GaN samples obtained at the different temperatures are investigated. ► The GaN sample has oxidation resistance and good thermal stability below 1000 °C. -- Abstract: Nanocrystalline gallium nitride was synthesized by a solid-state reaction of metallic magnesium powder, gallium sesquioxide and sodium amide in a stainless steel autoclave at a relatively low temperature (400–550 °C). The structures and morphologies of the obtained products were derived from X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). XRD patterns indicated that the products were hexagonal GaN (JCPDS card no. 76-0703). The influence of reaction temperature on size of the products was studied by XRD and TEM. Furthermore, the thermal stability and oxidation resistance of the nanocrystalline GaN were also investigated. It had good thermal stability and oxidation resistance below 800 °C in air.

  20. Crystallographic alignment of high-density gallium nitride nanowire arrays.

    Science.gov (United States)

    Kuykendall, Tevye; Pauzauskie, Peter J; Zhang, Yanfeng; Goldberger, Joshua; Sirbuly, Donald; Denlinger, Jonathan; Yang, Peidong

    2004-08-01

    Single-crystalline, one-dimensional semiconductor nanostructures are considered to be one of the critical building blocks for nanoscale optoelectronics. Elucidation of the vapour-liquid-solid growth mechanism has already enabled precise control over nanowire position and size, yet to date, no reports have demonstrated the ability to choose from different crystallographic growth directions of a nanowire array. Control over the nanowire growth direction is extremely desirable, in that anisotropic parameters such as thermal and electrical conductivity, index of refraction, piezoelectric polarization, and bandgap may be used to tune the physical properties of nanowires made from a given material. Here we demonstrate the use of metal-organic chemical vapour deposition (MOCVD) and appropriate substrate selection to control the crystallographic growth directions of high-density arrays of gallium nitride nanowires with distinct geometric and physical properties. Epitaxial growth of wurtzite gallium nitride on (100) gamma-LiAlO(2) and (111) MgO single-crystal substrates resulted in the selective growth of nanowires in the orthogonal [1\\[Evec]0] and [001] directions, exhibiting triangular and hexagonal cross-sections and drastically different optical emission. The MOCVD process is entirely compatible with the current GaN thin-film technology, which would lead to easy scale-up and device integration.

  1. Single step low temperature synthesis of gadolinium gallium garnet nanopowders

    Institute of Scientific and Technical Information of China (English)

    Rekha Mann; Kiranmala Laishram; Neelam Malhan

    2012-01-01

    Solution combustion synthesis of single-phase gadolinium gallium oxide (Gd3Ga5O12,GGG) nanopowders,by a fuel mixture approach using urea and glycine at a low temperature of 500 ℃,was being reported for the first time.Based on the fact that urea and glycine are good fuels for gallium oxide and gadolinium oxide synthesis,the fuel mixture composition was obtained,which could lead to direct phase pure cubic Gd3Ga5O12 formation without any subsequent calcination step.Combustion was carried out in furnace pre-heated at 500 ℃.Thermogravimetric analysis (TGA) of combustion product showed negligible mass loss indicating direct formation of GGG powder.Fourier transform infrared (FTIR) spectrum of combusted product showed peak characteristic of GGG in case of mixed fuel.X-ray diffraction (XRD) confirmed formation of phase pure GGG at 500 ℃ in preheated furnace.Very fine,well dispersed nanometric particles of size range of 50-100 nm were obtained,being uniform and close to spherical morphology as observed by transmission electron microscope (TEM).

  2. Spontaneous and strong multi-layer graphene n-doping on soda-lime glass and its application in graphene-semiconductor junctions

    Science.gov (United States)

    Dissanayake, D. M. N. M.; Ashraf, A.; Dwyer, D.; Kisslinger, K.; Zhang, L.; Pang, Y.; Efstathiadis, H.; Eisaman, M. D.

    2016-02-01

    Scalable and low-cost doping of graphene could improve technologies in a wide range of fields such as microelectronics, optoelectronics, and energy storage. While achieving strong p-doping is relatively straightforward, non-electrostatic approaches to n-dope graphene, such as chemical doping, have yielded electron densities of 9.5 × 1012 e/cm2 or below. Furthermore, chemical doping is susceptible to degradation and can adversely affect intrinsic graphene’s properties. Here we demonstrate strong (1.33 × 1013 e/cm2), robust, and spontaneous graphene n-doping on a soda-lime-glass substrate via surface-transfer doping from Na without any external chemical, high-temperature, or vacuum processes. Remarkably, the n-doping reaches 2.11 × 1013 e/cm2 when graphene is transferred onto a p-type copper indium gallium diselenide (CIGS) semiconductor that itself has been deposited onto soda-lime-glass, via surface-transfer doping from Na atoms that diffuse to the CIGS surface. Using this effect, we demonstrate an n-graphene/p-semiconductor Schottky junction with ideality factor of 1.21 and strong photo-response. The ability to achieve strong and persistent graphene n-doping on low-cost, industry-standard materials paves the way toward an entirely new class of graphene-based devices such as photodetectors, photovoltaics, sensors, batteries, and supercapacitors.

  3. Gallium-67 scintigraphy and intraabdominal sepsis. Clinical experience in 140 patients with suspected intraabdominal abscess

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, G.B.; Kan, M.; Mende, C.W.

    1976-12-01

    In 140 patients with suspected intraabdominal abscess, studies were made using gallium-67 citrate and technetium-99m labeled radiopharmaceuticals. Gallium-67 scintigrams correctly localized 52 of 56 intraabdominal abscesses confirmed at surgical operation or necropsy. In an additional 20 patients in whom findings on scintigrams were abnormal, there were clinically established infections. Sixty-one patients in whom findings on scintigrams were normal were conservatively managed and discharged from the hospital; none proved to have an abscess. Four false-negative and three false-positive studies were recorded. Gallium-67 scintigraphy is a useful noninvasive diagnostic adjunct that should be employed early in the evaluation of patients with suspected intraabdominal sepsis.

  4. Superconductivity and ferromagnetism in hole-doped RbEuFe4As4

    Science.gov (United States)

    Liu, Yi; Liu, Ya-Bin; Tang, Zhang-Tu; Jiang, Hao; Wang, Zhi-Cheng; Ablimit, Abduweli; Jiao, Wen-He; Tao, Qian; Feng, Chun-Mu; Xu, Zhu-An; Cao, Guang-Han

    2016-06-01

    We discover a robust coexistence of superconductivity and ferromagnetism in an iron arsenide RbEuFe4As4 . The new material crystallizes in an intergrowth structure of RbFe2As2 and EuFe2As2 , such that the Eu sublattice turns out to be primitive instead of being body-centered in EuFe2As2 . The FeAs layers, featured by asymmetric As coordinations, are hole doped due to charge homogenization. Our combined measurements of electrical transport, magnetization, and heat capacity unambiguously and consistently indicate bulk superconductivity at 36.5 K in the FeAs layers and ferromagnetism at 15 K in the Eu sublattice. Interestingly, the Eu-spin ferromagnetic ordering belongs to a rare third-order transition, according to the Ehrenfest classification of phase transitions. We also identify an additional anomaly at ˜5 K, which is possibly associated with the interplay between superconductivity and ferromagnetism.

  5. Superconductivity in gallium-implanted silicon; Supraleitung in Gallium-implantiertem Silizium

    Energy Technology Data Exchange (ETDEWEB)

    Skrotzki, Richard

    2016-07-12

    The following thesis is devoted to the electrical characterization of 10 nm thin layers consisting of amorphous Ga nanoclusters embedded in Ga-doped polycrystalline Si. The preparation of the layers is realized via ion implantation in Si wafers plus subsequent thermal annealing. Electrical-transport measurements in magnetic fields of up to 50 T show that the layers undergo two structural superconductor-insulator transitions upon variation of the annealing parameters. Structural analyzes based on TEM investigations reveal an underlying transformation of the size and distance of the clusters. This influences the interplay of the superconducting cluster coupling and capacitive charging energy as well as the extent of thermal and quantum fluctuations. In the superconducting regime (Tc ∼ 7 K) a double-reentrant phenomenon is observed. Here, magnetic fields of several Tesla facilitate superconductivity in an anisotropic way. A qualitative explanation is given via a self-developed theoretical model based on phase-slip events for Josephson-junction arrays. With respect to applications regarding sensor technology and quantum logic circuits the layers are successfully micro- and nanostructured via photolithography and FIB. This allows for the first observation of the Little-Parks effect in a nanostructure of amorphous Ga.

  6. Spectral variation of light-emitting diodes based on organic molecules doped polymer

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Organic light-emitting diodes based on naphthylimine-gallium complexes doped into a PPV derivative have been fabricated by a spin coating method.Color variation from green to blue with increase of the applied voltage has been observed.And the electroluminescent intensity of the blend samples is much stronger than that of the samples containing the complexes only.The results have been attributed to the variation of the recombination zone and the charge transfer between the materials.The process of the charge transport has been analyzed in detail.

  7. Multiband Gutzwiller theory of the band magnetism of LaO iron arsenide; Multiband Gutzwiller-Theorie des Bandmagnetismus von LaO-Eisen-Arsenid

    Energy Technology Data Exchange (ETDEWEB)

    Schickling, Tobias

    2012-02-23

    In this work we apply the Gutzwiller theory for various models for LaOFeAs. It was discovered in 2008 that doped LaOFeAs is superconducting below a temperature of T{sub c} = 28 K. Soon after that discovery, more iron based materials were found which have an atomic structure that is similar to the one of LaOFeAs and which are also superconducting. These materials form the class of iron-based superconductors. Many properties of this material class are in astonishing agreement with the properties of the cuprates. Therefore, studying this new material may promote our understanding of high-T{sub c} superconductivity. Despite great efforts, however, Density Functional Theory calculations cannot reproduce the small magnetic moment in the ground state of undoped LaOFeAs. Such calculations overestimate the magnetic moment by a factor 2-3. Within our Gutzwiller approach, we take additional local Coulomb correlations into account. We show that it is necessary to work with the iron 3d-orbitals and the arsenic 4p-orbitals to obtain a realistic description of LaOFeAs. For a broad parameter regime of the electronic interactions, we find a magnetic moment that is in the region of the experimentally observed values. We claim that the magnetic phase in LaOFeAs can be described as a spin-density wave of Landau-Gutzwiller quasi-particles.

  8. Optical Refrigeration

    Science.gov (United States)

    2007-12-01

    glasses and crystals doped with Yb3+ (ZBLANP (refs 16–19), ZBLAN (refs 20,21), CNBZn (refs 22,23), BIG (refs 23,24), KGd(WO4)2 (ref. 22), KY(WO4)2...cooling in the Yb3+-doped fluorozirconate glass ZBLAN . Phys. Rev. B 75, 144302 (2007). 35. Seletskiy, D., Hasselbeck, M. P., Sheik-Bahae, M. & Epstein, R...confined to either glasses and crystals doped with rare-earth (RE) elements or direct-bandgap semiconductors such as gallium arsenide. Although laser

  9. Limits on nu_e and anti-nu_e disappearance from Gallium and reactor experiments

    CERN Document Server

    Acero, Mario A; Laveder, Marco

    2007-01-01

    The disappearance of electron neutrinos observed in the Gallium radioactive source experiments is analyzed in the framework of two-neutrino mixing. It is shown that there is an indication of neutrino disappearance due to neutrino oscillations with sin^2 2 theta >~ 0.04 and Delta m^2 >~ 0.1 eV^2. The compatibility of this result with the data of the Bugey and Chooz reactor short-baseline antineutrino disappearance experiments is studied. It is found that the Bugey data present a weak indication in favor of neutrino oscillations with 0.02 <~ sin^2 2 theta <~ 0.08 and Delta m^2 =~ 1.85 eV^2, which is compatible with the Gallium allowed region of the mixing parameters. This indication persists in the combined analyses of Bugey and Chooz data, of Gallium and Bugey data, and of Gallium, Bugey, and Chooz data.

  10. Homogeneous dispersion of gallium nitride nanoparticles in a boron nitride matrix by nitridation with urea.

    Science.gov (United States)

    Kusunose, Takafumi; Sekino, Tohru; Ando, Yoichi

    2010-07-01

    A Gallium Nitride (GaN) dispersed boron nitride (BN) nanocomposite powder was synthesized by heating a mixture of gallium nitrate, boric acid, and urea in a hydrogen atmosphere. Before heat treatment, crystalline phases of urea, boric acid, and gallium nitrate were recognized, but an amorphous material was produced by heat treatment at 400 degrees C, and then was transformed into GaN and turbostratic BN (t-BN) by further heat treatment at 800 degrees C. TEM obsevations of this composite powder revealed that single nanosized GaN particles were homogeneously dispersed in a BN matrix. Homogeneous dispersion of GaN nanoparticles was thought to be attained by simultaneously nitriding gallium nitrate and boric acid to GaN and BN with urea.

  11. Efficient bifunctional gallium-68 chelators for positron emission tomography: tris(hydroxypyridinone) ligands

    OpenAIRE

    Berry, David J; Ma, Yongmin; Ballinger, James R.; Tavaré, Richard; Koers, Alexander; Sunassee, Kavitha; Zhou, Tao; Nawaz, Saima; Mullen, Gregory E. D.; Robert C. Hider; Blower, Philip J.

    2011-01-01

    A new tripodal tris(hydroxypyridinone) bifunctional chelator for gallium allows easy production of 68Ga-labelled proteins rapidly under mild conditions in high yields at exceptionally high specific activity and low concentration.

  12. A generator-produced gallium-68 radiopharmaceutical for PET imaging of myocardial perfusion

    National Research Council Canada - National Science Library

    Sharma, Vijay; Sivapackiam, Jothilingam; Harpstrite, Scott E; Prior, Julie L; Gu, Hannah; Rath, Nigam P; Piwnica-Worms, David

    2014-01-01

    ... incorporating alternative radionuclides. Recently, germanium/gallium (Ge/Ga) generators capable of producing high quality 68Ga, an isotope with excellent emission characteristics for clinical PET imaging, have emerged...

  13. Heterotopic ossification (myositis ossificans) in acquired immune deficiency syndrome. Detection by gallium scintigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Drane, W.E.; Tipler, B.M.

    1987-06-01

    A case of heterotopic ossification (myositis ossificans) secondary to the central nervous system complications of acquired immune deficiency syndrome (AIDS) is reported. Because of the overwhelming suspicion of infection in this patient, this diagnosis was not considered until a gallium scan revealed the typical findings of heterotopic ossification. Because of the increasing utilization of gallium imaging in the AIDS population, every imaging specialist should be aware of this potential disorder.

  14. Heterotopic ossification (myositis ossificans) in acquired immune deficiency syndrome. Detection by gallium scintigraphy.

    Science.gov (United States)

    Drane, W E; Tipler, B M

    1987-06-01

    A case of heterotopic ossification (myositis ossificans) secondary to the central nervous system complications of acquired immune deficiency syndrome (AIDS) is reported. Because of the overwhelming suspicion of infection in this patient, this diagnosis was not considered until a gallium scan revealed the typical findings of heterotopic ossification. Because of the increasing utilization of gallium imaging in the AIDS population, every imaging specialist should be aware of this potential disorder.

  15. The Role of Gallium scanning in the detection of bone and joint sepsis

    OpenAIRE

    Gavin, Anna; Laird, J. D.; Roberts, S.D.

    1984-01-01

    The value of gallium (67Ga) scanning in the diagnosis of septic disease of bone or joint was assessed in 34 patients. The results show a sensitivity of 60 per cent and specificity of 64 per cent. The low accuracy of this method for the detection of bone and joint sepsis (62 per cent) means that gallium scanning can be used only as an adjunct to other investigative techniques.

  16. Evaluation of Magnetostrictive Shunt Damper Performance Using Iron (Fe)-Gallium (Ga) Alloy

    Science.gov (United States)

    2013-09-01

    Evaluation of Magnetostrictive Shunt Damper Performance Using Iron (Fe)-Gallium (Ga) Alloy by Andrew James Murray and Dr. JinHyeong Yoo...Aberdeen Proving Ground, MD 21005 ARL-TN-0566 September 2013 Evaluation of Magnetostrictive Shunt Damper Performance Using Iron (Fe... Magnetostrictive Shunt Damper Performance Using Iron (Fe)- Gallium (Ga) Alloy 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6

  17. Haemophilus parainfluenzae bacteremia associated with a pacemaker wire localized by gallium scan

    Energy Technology Data Exchange (ETDEWEB)

    Rosenbaum, G.S.; Calubiran, O.; Cunha, B.A. (Winthrop-Univ. Hospital, Mineola, NY (USA))

    1990-05-01

    A young woman with a history of sick sinus syndrome and placement of a permanent pacemaker 6 months before admission had fever and Haemophilus parainfluenzae bacteremia. A gallium scan localized the infection to the site of the pacemaker wire. Echocardiograms were negative for any vegetations. The patient responded to cefotaxime and trimethoprim-sulfamethoxazole therapy. We believe that this is the first case of H. parainfluenzae bacteremia associated with a pacemaker wire and localized by gallium scan.

  18. High T(c) electron doped Ca10(Pt3As8)(Fe2As2)5 and Ca10(Pt4As8)(Fe2As2)5 superconductors with skutterudite intermediary layers.

    Science.gov (United States)

    Ni, Ni; Allred, Jared M; Chan, Benny C; Cava, Robert Joseph

    2011-11-01

    It has been argued that the very high transition temperatures of the highest T(c) cuprate superconductors are facilitated by enhanced CuO(2) plane coupling through heavy metal oxide intermediary layers. Whether enhanced coupling through intermediary layers can also influence T(c) in the new high T(c) iron arsenide superconductors has never been tested due the lack of appropriate systems for study. Here we report the crystal structures and properties of two iron arsenide superconductors, Ca(10)(Pt(3)As(8))(Fe(2)As(2))(5) (the "10-3-8 phase") and Ca(10)(Pt(4)As(8))(Fe(2)As(2))(5) (the "10-4-8 phase"). Based on -Ca-(Pt(n)As(8))-Ca-Fe(2)As(2)- layer stacking, these are very similar compounds for which the most important differences lie in the structural and electronic characteristics of the intermediary platinum arsenide layers. Electron doping through partial substitution of Pt for Fe in the FeAs layers leads to T(c) of 11 K in the 10-3-8 phase and 26 K in the 10-4-8 phase. The often-cited empirical rule in the arsenide superconductor literature relating T(c) to As-Fe-As bond angles does not explain the observed differences in T(c) of the two phases; rather, comparison suggests the presence of stronger FeAs interlayer coupling in the 10-4-8 phase arising from the two-channel interlayer interactions and the metallic nature of its intermediary Pt(4)As(8) layer. The interlayer coupling is thus revealed as important in enhancing T(c) in the iron pnictide superconductors.

  19. Kinetics of and atmospheric effects on gallium removal from a CeO{sub 2} based mixed oxide surrogate

    Energy Technology Data Exchange (ETDEWEB)

    Park, Y.S.; Taylor, T.N.; Atencio, A.; Butt, D.P.

    1998-12-31

    This paper describes preliminary experimental results on the kinetics of Ga removal from Ga{sub 2}O{sub 3}-doped CeO{sub 2{minus}x}, a surrogate for weapons grade PuO{sub 2{minus}x}. Ga is removed from the surrogate feedstock material using thermal techniques. An Ar-6% H{sub 2} gas was used in order to reduce the oxide to gaseous Ga{sub 2}O. Experiments were done in the temperature range of 600--1,200 C as a function of time, gas flow rate, and sample geometry. Samples were analyzed through measurements of weight change, scanning electron microscopy/energy dispersive spectroscopy, x-ray photoelectron spectroscopy, proton induced x-ray emission, and direct current plasma analysis. Gallium levels were reduced by as much as 98% (130 ppm Ga residue) of that in the starting material. Studies to date have shown CeO{sub 2{minus}x} is a very good surrogate for PuO{sub 2{minus}x}.

  20. Fabrication and properties of gallium phosphide variable colour displays

    Science.gov (United States)

    Effer, D.; Macdonald, R. A.; Macgregor, G. M.; Webb, W. A.; Kennedy, D. I.

    1973-01-01

    The unique properties of single-junction gallium phosphide devices incorporating both red and green radiative recombination centers were investigated in application to the fabrication of monolithic 5 x 7 displays capable of displaying symbolic and alphanumeric information in a multicolor format. A number of potentially suitable material preparation techniques were evaluated in terms of both material properties and device performance. Optimum results were obtained for double liquid-phase-epitaxial process in which an open-tube dipping technique was used for n-layer growth and a sealed tipping procedure for subsequent p-layer growth. It was demonstrated that to prepare devices exhibiting a satisfactory range of dominant wavelengths which can be perceived as distinct emission colors extending from the red through green region of the visible spectrum involves a compromise between the material properties necessary for efficient red emission and those considered optimum for efficient green emission.