Towards an optimal integrated reservoir system management for the Awash River Basin, Ethiopia

Science.gov (United States)

Müller, Ruben; Gebretsadik, Henok Y.; Schütze, Niels

2016-05-01

Recently, the Kessem-Tendaho project is completed to bring about socioeconomic development and growth in the Awash River Basin, Ethiopia. To support reservoir Koka, two new reservoirs where built together with extensive infrastructure for new irrigation projects. For best possible socioeconomic benefits under conflicting management goals, like energy production at three hydropower stations and basin wide water supply at various sites, an integrated reservoir system management is required. To satisfy the multi-purpose nature of the reservoir system, multi-objective parameterization-simulation-optimization model is applied. Different Pareto-optimal trade-off solutions between water supply and hydro-power generation are provided for two scenarios (i) recent conditions and (ii) future planned increases for Tendaho and Upper Awash Irrigation projects. Reservoir performance is further assessed under (i) rule curves with a high degree of freedom - this allows for best performance, but may result in rules curves to variable for real word operation and (ii) smooth rule curves, obtained by artificial neuronal networks. The results show no performance penalty for smooth rule curves under future conditions but a notable penalty under recent conditions.

Profitability diagnosis of refinery and improvement proposal; Seiyusho no shueki shindan to kaizen teian

Energy Technology Data Exchange (ETDEWEB)

Aoyama, H.

2000-07-01

Based on consulting service RPS-J under joint operation of Nikki, UOP LLC of U.S.A. and Nikki Universal, approaching ways applied for profitability improvement and improvement proposal for refineries and analyzing techniques used for resolution of process bottlenecks were described. In RPS-J, themes of (1) energy saving, (2) quality upgrading, (3) improvement of disintegrating ratio, (4) reduction of give-away, (5) improvement of equipment operation ratio, (6) reduction of maintenance cost, (7) effective utilization of catalysts, are considered for profitability improvement fields. Procedures from idea excavation for profitability improvement to realization of profitability improvement are carried out in the order of, (1) Grasping of the present state, (2) Excavation of improving items and selection, (3) Quantitative evaluation of draft profitability improvement plan and focusing, (4) Profitability improvement by operation improvement, (5) Profitability improvement by minor improvement, (6) Profitability improvement in middle- and long-term vision, (7) Final focusing by feasibility study. Afterwards, examination to economically solve bottlenecks of critical facilities, examination on bottlenecks of distillation tower and refining tower and utility analysis are carried out. RPS-J was already applied to 4 refineries including Muroran Refinery and Negishi Refinery of Nisseki Mitsubishi, and profitability improvement themes were found to improve profitability of 50 to 150 cents per barrel. (NEDO)

Towards an optimal integrated reservoir system management for the Awash River Basin, Ethiopia

Directory of Open Access Journals (Sweden)

R. Müller

2016-05-01

Full Text Available Recently, the Kessem–Tendaho project is completed to bring about socioeconomic development and growth in the Awash River Basin, Ethiopia. To support reservoir Koka, two new reservoirs where built together with extensive infrastructure for new irrigation projects. For best possible socioeconomic benefits under conflicting management goals, like energy production at three hydropower stations and basin wide water supply at various sites, an integrated reservoir system management is required. To satisfy the multi-purpose nature of the reservoir system, multi-objective parameterization-simulation-optimization model is applied. Different Pareto-optimal trade-off solutions between water supply and hydro-power generation are provided for two scenarios (i recent conditions and (ii future planned increases for Tendaho and Upper Awash Irrigation projects. Reservoir performance is further assessed under (i rule curves with a high degree of freedom – this allows for best performance, but may result in rules curves to variable for real word operation and (ii smooth rule curves, obtained by artificial neuronal networks. The results show no performance penalty for smooth rule curves under future conditions but a notable penalty under recent conditions.

The Study of Africa: A challenge for the African Renaissance | Koka ...

African Journals Online (AJOL)

It is said, according to the Afrikan Proverb: “Until the Lions have their own historians tales of hunting will always glorify the hunter.” That is, not until Afrika can have its own scholars to present her case in world forums it will always suffer from mis-interpretations, misrepresentations and mis-presentations of her views and ...

Cardiovascular angiography system Infinix{sub TM} CB; Shinzoyo junkanki shindan system Infinix{sub TM} CB

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A cardiovascular angiography system Infinix{sub TM} CB is developed, which is a dedicated system for cardiovascular catheter treatment (intervention), from PTCA (percutaneous transluminal coronary angioplasty) down, capable of two-way biplanar photography. It is designed to be thoroughly operator-friendly, and some of its features are stated below. It is capable of high-speed biplanar positioning at the maximum speed of 10 degrees/second (25% faster than in the conventional type). A side beam vertical motion mechanism is provided rendering biplanar framing faster and easier. Hyper-handling is embodied with ergonomics introduced into the system. (translated by NEDO)

Cardiovascular angiography system Infinix[sub TM] CB. Shinzoyo junkanki shindan system Infinix[sub TM] CB

Energy Technology Data Exchange (ETDEWEB)

1999-03-01

A cardiovascular angiography system Infinix[sub TM] CB is developed, which is a dedicated system for cardiovascular catheter treatment (intervention), from PTCA (percutaneous transluminal coronary angioplasty) down, capable of two-way biplanar photography. It is designed to be thoroughly operator-friendly, and some of its features are stated below. It is capable of high-speed biplanar positioning at the maximum speed of 10 degrees/second (25% faster than in the conventional type). A side beam vertical motion mechanism is provided rendering biplanar framing faster and easier. Hyper-handling is embodied with ergonomics introduced into the system. (translated by NEDO)

Socio-psycho-historical observation on the twin. Sampling methods and case study of the atomic bomb exposed twins

Energy Technology Data Exchange (ETDEWEB)

Watanabe, S; Satow, Y; Ueoka, Hiroshi; Munaka, M; Kurihara, M [Hiroshima Univ. (Japan). Research Inst. for Nuclear Medicine and Biology

1980-07-01

The so-called ''twin control study'', mainly on the monozygotic twins one of which was A-bomb exposed and the other was non-exposed were carried out. Sampling was conducted utilizing the materials as follows: 1) The survey on casualities of A-bomb exposed families in Hiroshima which was undertaken in 1946. 2) The survey of A-bomb survivors in 1965. 3) A-bomb exposed family survey conducted between 1973 to 1975. 4) Investigations of A-bomb victims exposed in the proximal areas from the hypocenter. From the above mentioned materials 470 pairs were selected, of which 220 were exposed. Among them 172 pairs were twins of the same sex. Female and male pair were also employed. In one case they were exposed, while the others were nonexposed. Two pairs were examined under the following methods: 1) Depth interview to ascertain familial casualities with reference to the family life cycle. 2) Socio-historical research. 3) Motoaki's Jinkaku Shindan Kensa (Modified Rorschach test by H. Motoaki), and T.A.T. test. Results obtained were summarized as follows: 1) Both pairs of twins were of similar appearance and personality traits, and had a strong feeling of companionship for each other. 2) In family relationships, the persons studied were very conscious of the role expectations of elder and younger siblings in the twin pairs. 3) Through depth interviews and projective tests, A-bomb exposed pairs still showed deep psychological stresses, resulting from the A-bomb disaster. 4) Both among the exposed twins and within the nonexposed control group twin siblings had a close feeling of companionship for each other. However, nonexposed twins could not understand the psychological experience of twins who had been subjected to the atomic disaster.

Socio-psycho-historical observation on the twin

International Nuclear Information System (INIS)

Watanabe, Shoji; Satow, Yukio; Ueoka, Hiroshi; Munaka, Masaki; Kurihara, Minoru

1980-01-01

The so-called ''twin control study'', mainly on the monozygotic twins one of which was A-bomb exposed and the other was non-exposed were carried out. Sampling was conducted utilizing the materials as follows: 1) The survey on casualities of A-bomb exposed families in Hiroshima which was undertaken in 1946. 2) The survey of A-bomb survivors in 1965. 3) A-bomb exposed family survey conducted between 1973 to 1975. 4) Investigations of A-bomb victims exposed in the proximal areas from the hypocenter. From the above mentioned materials 470 pairs were selected, of which 220 were exposed. Among them 172 pairs were twins of the same sex. Female and male pair were also employed. In one case they were exposed, while the others were nonexposed. Two pairs were examined under the following methods: 1) Depth interview to ascertain familial casualities with reference to the family life cycle. 2) Socio-historical research. 3) Motoaki's Jinkaku Shindan Kensa (Modified Rorschach test by H. Motoaki), and T.A.T. test. Results obtained were summarized as follows: 1) Both pairs of twins were similar appearance, and also personality traits, and had a strong feeling of companionship for each other. 2) In family relationships, the persons studied were very conscious of the role expectations of elder and younger siblings in the twin pairs. 3) Through depth interview and projective test, A-bomb exposed pairs still showed deep psychological stresses, resulting from the A-bomb disaster. 4) Both among the exposed twins and within the nonexposed control group twin siblings had a close feeling of companionship for each other. However, nonexposed twins could not understand the psychological experience of twins who had been subjected to the atomic disaster. (author)

Nonlinear effect in vibroseis data; Vibroseis kiroku ni oite mitomerareru hisenkei koka

Energy Technology Data Exchange (ETDEWEB)

Saeki, T [Japan National Oil Corp., Tokyo (Japan)

1997-05-27

This paper describes nonlinear effect recognized in Vibroseis data. Harmonics is a wave of frequency in integer factors generated in association with basic sweep vibrated by Vibroseis. Harmonics is generated because vibration in the vicinity of seismic source contains nonlinear terms. Seismic exploration using the reflection method often discusses propagation of seismic waves hypothesized as a linear phenomenon. Vibroseis data analysis, however, requires evaluation of the effect of the harmonics on accuracy. Vibroseis investigation measures may be taken by eliminating n-order harmonics by using the phase control method, and generating seismic source sweep in which the phase is shifted by 180/(n-1) each time in order to leave the basic sweep. Methods to increase the sweep length include a method to expel strain to a location outside the range of the subject travel time. Up-sweep (a sweep changing from low frequencies to higher frequencies) is also a means capable of avoiding harmonics effects. Vibroseis investigations currently performed adopt this method frequently because of it having little technological and economic problems. 10 refs., 3 figs.

Development of diagnosis and repair system for steelmaking refractories; Seikoyo taikabutsu no shindan hoshu gijutsu no kakuritsu

Energy Technology Data Exchange (ETDEWEB)

Aso, S.; Harada, S.; Tsutsui, Y. [Nippon Steel Corp., Tokyo (Japan)

1996-06-01

The latest measurement equipment and repair method were introduced into the work area of all refractories in the process of torpedo cars, hot metal preliminary treatment, hot metal pans, secondary refining, and cast pans so as to improve the cost of the newest advanced steelmaking refractories. As a result, the refractory cost could be reduced by 10%. This paper introduces the improvement in RH refractories and refractories for hot metal preliminary treatment. As for basic items, in addition to the visual observation, the thickness of refractories was quantified using equipment (laser profile meter, thermotracer, and NS sensor) for the furnace stop in the minimum remaining length. An ITV was also installed in the facilities where the visual check is difficult to carry out. Repair is mainly done by spraying. A thermal spraying repair method with high durability was used for the repair. A method that relieves a thermal shock was used for preheating. Moreover, measures that make the temperature gradient in the thickness direction uniform by using newly developed microwave drying equipment were taken for drying of unburned refractories. 4 refs., 13 figs., 2 tabs.

Hydrology and Mosquito Population Dynamics around a Hydropower Reservoir in Africa

Science.gov (United States)

Endo, N.; Eltahir, E. A.

2013-12-01

Malaria is associated with dams because their reservoirs provide mosquitoes, the vector of malaria, with permanent breeding sites. The risk of contracting malaria is likely to be enhanced following the increasing trend of hydropower dam construction to satisfy the expanding energy needs in developing countries. A close examination of its adverse health impacts is critical in the design, construction, and operation phases. We will present results of extensive field studies in 2012 and 2013 around the Koka Reservoir, Ethiopia. The results uncover the importance of reservoir management especially after the rainy seasons. Furthermore, we show the capability of a newly modified hydrology, entomology and malaria transmission simulator, HYDREMATS (Bomblies et al, 2008), and its potential as a tool for evaluating environmental management strategies to control malaria. HYDREMATS was developed to represent how the hydrology in nearby villages is impacted by the reservoir system, and the role of different types of vector ecologies associated with different Anopheles mosquito species. The hydrology component of HYDREMATS simulates three different mosquito breeding habitats: rain-fed pools, groundwater pools, and shoreline water. The entomology component simulates the life cycles of An. funestus and An. arabiensis, the two main vectors around the reservoir. The model was calibrated over the 2012-2013 period. The impact of reservoir water level management on the mosquito population is explored based on numerical model simulations and field experiments.

1-12 Soil Fertility in Koka Nagawo Area of Lumme District in East Shoa

African Journals Online (AJOL)

tosheba

Abstract: For designing proper soil fertility management interventions, locally ... District in East Shoa Zone of Oromia Regional State, Ethiopia, based on ..... Selected soil physico-chemical properties across different land units. ..... facilitating the study and the research work. 6. ... Characteristics of the Soils of the North-western.

Analysis and scavenging effect of acid fog. Sanseimu no kagaku sosei to senjo koka

Energy Technology Data Exchange (ETDEWEB)

Igawa, M.; Hoka, E.; Hosono, T.; Iwase, K.; Nagashima, T. (Kanagawa University, Yokohama (Japan). Faculty of Engineering)

1991-05-10

Fog samples were collected for analysis at Mt. Ohyama, the east edge of Tanzawa Mountains in the southwest of Kanto plains. Then, rainwater and aerosol that becomes the core of droplet were analyzed and measured values were compared. As a result, the pH value of the fog samples for 2 years from 1988 to 1990 ranged between 2.6 and 7.0, and the mean pH value was 3.95. According to the measurement of major component concentration of fogwater, rainwater, and aerosol, it was found that concentration of fogwater changed significantly depending on the day but every ion concentration was higher than that of rainwater. The equivalent concentration ratio of sulfuric acid, nitric acid, and chloride ions were almost equal. The concentration value of fogwater varied a lot with the course of time and became higher during the formation and the dissipation of fog. Through the analysis of such changes, atmospheric scavenging effect of precipitation of fogwater upon the trees and the earth surface was observed. It means that pollutants with high concentration were loaded on the plants and the earth surface. 23 refs., 5 figs., 2 tabs.

Study on fault diagnostic system using modularized knowledge; Mojuru gata chishiki wo mochiita ijo shindan system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimada, Y.; Sayama, H.; Suzuki, K. [Okayama Univ. (Japan). Dept. of Industrial and Mechanical Engineering

1997-08-15

Recently, a fault diagnostic expert system was prosperously developed as an objective of chemical plants and nuclear power plants. In this paper, a fault diagnostic method using modularized knowledge was proposed, a fault diagnostic system was constructed for an experimental plant, and the effectiveness of this method was clarified by carrying out a fault diagnostic experiment. The characteristics of the proposed fault diagnostic system were as follows: The necessary knowledge for diagnosing faults was made into each process element. Based on this method, the revision and addition of a knowledge base could be carried out in each element, and the design change of a plant could be flexibly corresponded by only changing the related part of the process flow graph. The estimated results were stored into the working memory, not only faults of an element in which faults resulted could be estimated, but also the fault propagating path could be clarified. 8 refs., 6 figs., 3 tabs.

Effect of fall wind on wind power generation; Furyoku hatsuden ni okeru dashikaze no koka

Energy Technology Data Exchange (ETDEWEB)

Nagai, H [Nihon University, Tokyo (Japan)

1997-11-25

Wind conditions in Arakawa Town, Niigata Prefecture, were surveyed by anemometers and anemoscopes installed at 3 different points, and the data are analyzed to develop the prediction model for investigating possibility of introduction of wind mills there. Outlined herein is power generated by fall wind by comparing predicted power availability with the actual results. In order to investigate possibility of power generation by fall wind, the wind conditions and power availability are simulated using the observed wind condition data. Predicted wind velocity involves a large error at a point where frequency of prevailing wind direction is high, and direction in which average wind velocity is high coincides with direction in which land is slanted at a high slope. Fall wind occurs locally for geographical reasons. Location of the wind mill must be carefully considered, because it is complex, although potentially gives a larger quantity of power. A wind mill of 400kW can produce power of around 600MWh annually, when it is located at the suited site confirmed by the wind condition analysis results. 6 refs., 5 figs., 6 tabs.

Institutional trust in the national social security and municipal healthcare systems for the elderly in Japan.

Science.gov (United States)

Murayama, Hiroshi; Taguchi, Atsuko; Ryu, Shuhei; Nagata, Satoko; Murashima, Sachiyo

2012-09-01

Japanese social security systems and institutions for the elderly, as well as the general attitude toward elderly care services among the Japanese population, have been undergoing a dramatic change. By examining the association between institutional trust, which is a representative element of social capital, and anxiety regarding receiving elderly care, we can uncover clues toward building a more robust social security system for the elderly. This study examines the relationship between institutional trust, in the national social security and municipal healthcare systems for the elderly, and anxiety with respect to receiving elderly care among the general Japanese population. A cross-sectional survey was conducted using a self-administered questionnaire that was returned by mail in January and February 2005. The target population was 4735 community residents aged 20-75 years, who lived in the city of Koka, Shiga, Japan. A total of 2264 questionnaires were included in the analysis. A binominal logistic regression analysis showed that responses of 'trust' [odds ratio (OR): 2.09, 95% confidence interval (95% CI): 1.01-4.30] and 'strongly trust' (OR: 3.80, 95% CI: 1.55-9.31) for the national system were associated with not having anxiety regarding elderly care, compared with the reference category of feeling strongly distrust. However, trust in the municipal system showed no association with this anxiety. These results indicate the importance of developing strategies to increase a common trust in the national care services for the elderly to reduce the anxiety people feel regarding whether they will be able to receive elderly care when required.

Investigation into the emission of greenhouse effect gases; Onshitsu koka gas no haishutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper grasped the situation of greenhouse effect gas emissions of advanced countries based on the reports from them. The advanced countries which concluded the U.N. Framework Convention on Climate Change (OECD member countries, the former U.S.S.R., and East European countries) are to be reported to the office concerned with work for the framework the situation of their greenhouse effect gas emissions according to the obligation of the framework. In and after April 1997, they made the second report. The paper summarized changes in emission amount, the future trend, and the policies/measures mainly taken of nine countries which have already presented the second report (the U.S., the U.K., Germany, Holland, Italy, Norway, Sweden, Finland, and New Zealand) and one country (Russia) which has made only the first report. Moreover, the literature was collected and summed up concerning the mechanism and coefficients of the emission of nitrous oxide and methane. The collected literature was classified into all fields/plural number of fields, energy relation, industrial process relation, relation with the use of organic solvent and other products, agricultural relation, relation with changes in land use and forests, and waste relation. 4 figs., 228 tabs.

Development of sound absorption measuring system with acoustic chamber; Kogata kyuon koka sokutei sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takahira, M.; Noba, M. [Toyota Motor Corp., Aichi (Japan); Matsuoka, H. [Nippon Soken, Inc., Tokyo (Japan)

1998-05-01

In order to measure sound absorption performance necessary to develop sound absorption materials, development was made on a device consisting of a small sound box capable of measurement inexpensively and easily, as a measure against the reverberation chamber method. In order to obtain stabilized diffusion sound internally, the sound box has a shape of asymmetric seven-side body in which sides do not face squarely with each other. The box was so sized that a large number of resonant vibration postures can be constituted at the targeted frequency simultaneously in the box. The box has a commercially available cone speaker with good acoustic output characteristics in frequency range of higher than 500 Hz installed on an inner side of the box. The sound source uses a method to derive sound absorption rate from difference of sound pressure levels. In order to eliminate need of averaging treatment by using a multi-point measurement inside the box, a discussion was given to provide an opening on part of the box to place the sound receiving point outside the opening. A square test piece is placed on the floor 0.5 meter or more away from the speaker in the box. As a result of the experiment, it was verified that the sound absorption rate obtained by this device corresponds well with that by the reverberation chamber method. The size of the test piece was also found adequate. 2 refs., 11 figs., 1 tab.

Autosolvent effect of bitumen in thermal cracking; Netsubunkai hanno ni okeru bitumen no jiko yobai koka

Energy Technology Data Exchange (ETDEWEB)

Mikuni, M.; Sato, M.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Nagaishi, H.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

1996-10-28

Tar sand bitumen is petroleum-based ultra-heavy oil, and has a great amount of reserve like coal. However, there are still a lot of problems for its highly effective utilization. This paper discusses whether the light components in bitumen show independent behavior during the thermal cracking of heavy components, or not. Solvent effect and reaction mechanism during the thermal cracking are also derived from the change of their chemical structures. Athabasca tar sand bitumen was separated into light and heavy fractions by vacuum distillation based on D-1660 of ASTM. Mixtures of the both fractions at various ratios were used as samples. Negative effect of the light fraction on cracking of the heavy fraction was observed with dealkylation and paraffin formation Polymerization of the dealkylated light fraction to the heavy fraction was suggested due to lack of hydrogen in the thermal cracking under nitrogen atmosphere, which resulted in the formation of polymer. 3 refs., 6 figs.

Wind tunnel investigation of an STOL aircraft model. STOL zenki mokei-fudo shiken. ; Engine nacelle keijo koka

Energy Technology Data Exchange (ETDEWEB)

1993-01-01

The nacelle shape of a mimic engine mounted on the wind tunnel test model for an STOL aircraft developed by the National Aerospace Laboratory has much larger length than in the nacelle of a scale reduced to 8% of an actual engine, and the shape below the nacelle is different. Therefore, in order to estimate the air force in the actual aircraft from the aerodynamic data obtained in a wind tunnel test, the data are corrected by using differences in aerodynamic loads (estimated values) applied on the mimic engine and the actual engine. For the purpose of discussing the reasonability of this correction, an 8%-scale flow through nacelle with the same shape as in the actual aircraft (the actual aircraft type) and a flow through nacelle for a wind tunnel testing model of the experimental STOL aircraft were fabricated and wind tunnel tests were performed. These results were compared with the corrected results of the mimic engine wind tunnel test. As a result, it was made clear that the force data have been corrected excessively, and the moments have been corrected considerably well. 7 refs., 32 figs., 7 tabs.

Equalizing effect of the fluctuation in areal irradiance; Chiikinai ni okeru shugo nissha no hendo yokusei koka

Energy Technology Data Exchange (ETDEWEB)

Minowa, J; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K; Tsuda, I; Sakuta, K [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Aggravation in electric power quality is concerned because of irregular output power caused by a large number of photovoltaic power generation systems connected with the power grids. However, averaging of the irregularity may be expected in a wide area due to time-based shift in cloud movements. In order to identify this effect, insolation data were measured in terms of planes at multiple points in the city of Tsukuba to discuss the fluctuation equalizing effect. The system is composed of nine instruments to measure insolation plane characteristics, nine terminal station units, and a base station unit. The insolation data express the horizontal plane insolation intensity at a sampling interval of one minute. Insolation fluctuation (standard deviation of insolation fluctuation components) was defined as an index of the insolation fluctuation. Based on the index, an averaging effect when the photovoltaic systems are installed in a number of locations was considered by using statistic estimation. As a result, the averaging effect was obtained even in an area with a radius of several kilometers. In addition, the measurement data revealed that there is an upper limit in the effect depending on the number of system installation. It was also made clear that the data are affected by distances to connect the photovoltaic power generation systems with each other and by climatic conditions. 3 refs., 6 figs.

Trends for reduction of greenhouse gases (GHG) in Japan; Kokunai no onshitsu koka gas sakugen doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this research is to identify the problems and measures for reduction of GHG emissions by conducting research on the GHG emission trends in the energy-conversion, industry, public and transportation sectors, and policies and regulations. Japan`s total emission of CO2 in FY 1994 was 343 million tons in terms of carbon, and the emission per capita was 2.74 tons. These amounts were 7% increase in total CO2 emissions and 6% increase in the emission per capita compared with those in FY 1990. There were high increases in the public and transportation sectors. This trend is expected to continue in the future. Since more than 90% of CO2 emission is derived from energy origin, the climate change problems mean energy and economic problems. To attain Japan`s goal of the year 2000 with maintaining the appropriate economic growth, it is crucial to accelerate energy-efficiency and introduction of new energy. 19 figs., 28 tabs.

Complex of fiber and effects of mix spinning; Sen'i no fukugoka to konbo no koka

Energy Technology Data Exchange (ETDEWEB)

Matsui, N. [Asahi Chemical Industry Corp., Tokyo (Japan)

2000-03-01

In recently, comfortable life can be spent by performing complex of fibers. As complex of single fibers being materials of yarn, conjugate fiber is listed. Conjugate fiber is a fiber spun over 2 kind of polymer having different characteristics from one nozzle. There are sheath core type fibers as complex functional fibers. Static electricity prevention fibers can be prepared by putting conductive materials, for example, carbon black into core parts. After putting components being able to dissolve by specific solvents into core, hollow fibers can be prepared by dissolving core parts in near process to products. By reason of clothing contacting to skin directly in board aria and long time, fashionable characters of design and so on or comfortability of wearing are needed in many cases. In this reason, many kinds of fibers for clothing prepared complex yarn by being complex and by making the best use of good characteristics of each fibers, and developed a way to new function or new use. (NEDO)

Hyperthermia and massage are effect for the gingivitis improvement; Onnetsu to massaji ga shinikuen kaizen ni koka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

It was confirmed that Kao and research group of Nosaka professor of Iwate Medical Univ. faculty of dentistry that hyperthermia and massage at the 40 degrees C for the gingival activate the gingival lymph duct function and that it improves the gingivitis was effective. By causing the microcirculation disorder of the gingival, the research of the vascularisation is main until now for the gingivitis. Present research demonstrated that the recovery of the lymph duct function was effective for the gingivitis improvement for the first time in the world. (translated by NEDO)

Smoke reduction using multiple stage diesel combustion; Nidan nensho ni yoru diesel kikan no smoke teigen koka

Energy Technology Data Exchange (ETDEWEB)

Tsujimura, K. [Chiba Institute of Technology, Chiba (Japan); Hashizume, T.; Miyamoto, T.; Akagawa, H.

1999-09-25

A new diesel combustion concept termed MULDIC (MULtiple stage Diesel Combustion), which can reduce NO{sub x} emissions at high load conditions, was studied by means of engine test, combustion observation and numerical simulation. The engine test showed that simultaneous reduction of NO{sub x} and smoke could be obtained with MULDIC operation. In-cylinder combustion observation was carried out in order to clarify the cause of the smoke reduction of the MULDIC. In these photographs, a first stage combustion sins observed with nonluminous flame. In a second stage combustion, a highly sooting luminous flame was observed because the ignition delay was short. However this luminous flame disappeared quickly. Computational results showed that, oxygen is distributed evenly in the cylinder in later portion of the second stage combustion. Moreover, since cylinder temperature was very high, most of the soot oxidized rapidly. Thus, low smoke combustion was obtained. (author)

Study of evaluation for grouting effect in a borehole; Yakueki chunyu koka hyoka gijutsu ni okeru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, H; Matsuo, T [Fukuoka Municipal Transportation Bureau, Fukuoka (Japan); Yamauchi, Y; Imanishi, H [Osaka Soil Test, Osaka (Japan)

1996-10-01

For the foundation improvement works by grouting in a borehole, evaluation of grouting effect is one of the most important management items. The grouting design and works are sometimes reconsidered depending on the evaluation of grouting effect during the test injection. The purpose of the evaluation of grouting effect is to grasp the range of improvement and consolidation after the injection, and to judge and estimate the strength and permeability of the consolidation part. This paper describes the judgment method of the strength using PS logging results and borehole televiewer (BHTV) logging results. The reflection intensity (Ir) by the BHTV logging increased after the grouting, which showed a same tendency as that using S-wave and P-wave velocities (Vs and Vp) before and after the grouting. This was considered to demonstrate the grouting effect. A relation was obtained between the Vs, Vp and Ir before and after the grouting, which was expressed by following equation. Ir=0.143{times}Vs-70=0.093{times}Vp-110. The relation with the dynamic elastic coefficient (Ed) was also obtained as follow; Ir=0.0013{times}Ed. 9 figs.

ANALYSIS AND COMPARISON OF ADOLESCENT ATHLETES' MOTIVATION: BASKETBALL PLAYERS VS. FOOTBALL PLAYERS

Directory of Open Access Journals (Sweden)

Bartolom\\u00E9 J. Almagro

2009-01-01

Full Text Available The motivation of an athlete is determinant for the athletic engagement of the adolescent. The present study attempts to analyze the motivation of adolescent basketball and football players from the perspectives of Achievement Goal Theory (Nicholls, 1989 and Self-Determination Theory (Deci & Ryan, 1985. The study's sample was composed of 248 athletes from 12 to 17 years of age. Half were from basketball and half were from football. The instruments that were utilized were: the Spanish version of the Sport Motivation Scale (SMS (Núñez, Martín-Albo, Navarro, & González, 2006, the Spanish version of the Perceived Motivational Climate in Sport Questionnaire-2 (PMSCQ-2 (Balaguer, Mayo, Atienza, & Duda, 1997, and the adapted Spanish translation (Moreno, Moreno, & Cervelló, 2007 of the Intention to be Physically Active Scale (IPAS by Hein, Müür, and Koka (2004. The comparison of the means of the variables between football and basketball players was done utilizing the student t-test for independent samples. Significant differences were found for variables such as: intrinsic motivation (IM toward accomplishment, external regulation, amotivation, task, ego, and Self-Determination Index (SDI. Basketball players obtained higher values in the SDI, in task, and in IM toward accomplishment than football players. The search for premature performance in football and coaches' educations can help to explain these differences. The importance of these differences reside in the relationship between these motivational variables and the adherence to athletic practice. In conclusion, basketball demonstrated better values in motivational variables, which demonstrates that training sessions are more oriented toward task than ego, that players have more intrinsic and self-determined motivation, and therefore, the adherence of the young athletes will be greater in this sport.

Study on solar collector utilizing electro-hydrodynamical effect; Denki ryutai rikigaku koka wo riyosuru taiyo shunetsuki no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, M; Aoki, H; Wako, Y [Hachinohe Institute of Technology, Aomori (Japan)

1997-11-25

This paper proposes a cone type electro-hydrodynamical (EHD) heat collector, describes its structure and principle, and mentions possibility of improving the heat collecting efficiency. The paper proposes a heat collector with a shape close to a cone. Trees are of cone form so that their every leaf, branch and truck can capture solar energy efficiently. Imitating this fact existing in the natural world, a cone-shaped heat collector was fabricated on a trial basis to discuss its heat collecting efficiency. Furthermore, black round stones are placed in the inner cone of the cone- shaped heat collector of double-glass structure. A low boiling point medium is placed between the inner and outer cones to cause corona discharge in vapor generated by absorbing the solar heat, and generate corona wind for an attempt to accelerate heat transfer into a heat exchanger. Thus, development was made on a cone-shaped high-efficiency heat collector utilizing electro-hydrodynamical (EHD) effect, and elucidation was given on dynamic phenomena of an electro-thermal fluid. Heat transfer in the EHD heat collector has a possibility of being accelerated by generation of ionic wind. In addition, it is thought that there would be an optimum value in applied voltage to increase electric charge supply as a result of corona discharge. 1 ref., 2 figs.

Research of fragranced air, environmental aroma, to human and its application. Kankyo hoko no koka to sono oyo

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, S. (Shimizu Construction Co. Ltd., Tokyo (Japan))

1991-06-01

The effect of lemon, jasmine and lavender aroma on people was studied through environmental aroma experiments by 270 subjects in a meeting room for two months. As a result, the high percentage of positive responses was obtained on the sense of air cleanliness and efficiency of meetings, and a statistical significance was, in particular, obtained in the case of lemon as smoking was permitted. It was suggested that aroma had physiological and phychological effect even under conditions where the subjects were not necessarily aware of aroma. The effect of the same three aromas was also studied through experiments by 13 subjects in a VDT room for one month. As a result, the number of keypunch errors decreased in every aroma although punching speeds decreased slightly, and lemon showed a significant difference among three aromas. Based on these experimental results, the aroma generator was developed, and more than 30 environmental aroma systems combined with air conditioning ducts have been installed in Japan. 20 refs., 5 figs., 6 tabs.

Measuring approach for effect of refreshmental acceleration into the soil environment; Kankyo sosei kasoku koka no ikkeikeisoku apurochi

Energy Technology Data Exchange (ETDEWEB)

Isogai, H. [Electrotechnical Laboratorys, Tsukuba (Japan)

1998-12-05

This paper mainly describes to a measuring method for effect of refreshmental acceleration into the soil which were employing hamlet of micro organisms for accelerating revival or refreshment of environment especially purification of sludge in bottom of polluted ponds, lakes and grounds. (author)

Development of acoustic partial discharge detection device; Bubun hoden kenshutsusochi wo riyo shita onkyo niyoru hendensetsubi no zetsuen rekka shindan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Suenaga, Kiyoka [Kawasaki Steel Corp., Tokyo (Japan)

1999-06-15

This paper introduces an acoustic partial discharge detection device, consisting of a microphone, amplifier circuit for analog signals, A/D (Digital Signal Processor). This device has the following unique characteristics: (1) Judging whether or not there is partial discharge by analyzing supersonic signals. (2) High sensitivity for detecting discharge ; 100 pC from a distance of 1.2 m. (3)Locating the position of discharge occurrence by using a sharpe directional parabola microphone and laser beam pointer. The detector was used in the steel works to detect partial discharge on high-voltage electrical apparatus, where faults due to partial discharge were found in the potential transformer and current transformer. The effectiveness of the device was thus verified. (author)

Realization of an accelerator for environmental refreshment in case of soil; Fukyugata kasokuki ni yoru kankyo sosei eno koka

Energy Technology Data Exchange (ETDEWEB)

Isogai, H [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Learning from a history of the earth of ancient times, the paper studies effects of refreshing environment and soil or making them natural and harmless mostly using primitive bacteria, and develops element technology which is industrially accelerating. The spread type accelerator working only by solar energy was installed and operated for experiment. As indices of refreshment effects, a study was comparatively made between a sugar degree of sweet potato and a yield shown in the number of potatotimesunit weight. An EM propagation garbage layer is formed, and the two sections were installed of a site of the actual installation of the spread type accelerator and a site naturally left alone. Other effects of weather, temperature and humidity which are external factors and general fertilization are offset as common modes, and a consideration was so made that only refreshment effects of primitive bacteria can be relatively compared. Acceleration effects in using accelerator for growing sweet potato could be quantitatively confirmed. As to sugar degree, because the last study was made in the beginning of summer, the underground temperature was high enough. Even only EM effects were fully effective. This time, the weather was much colder, and it was found to be a must to use accelerator. 2 figs.

Education effect of solar car for technical high school student; Kogyo kokosei ni taisuru solar car no kyoiku koka

Energy Technology Data Exchange (ETDEWEB)

Inoue, T.

1998-09-30

The solar car race which technical high school students can join in was determined to be held at Ogata village, Akita prefecture. To join in the solar bicycle race, the author working in Ofuna technical high school called on 3 schools of Yokosuka, Fujisawa and Kanagawa technical high schools which joined in World Solar-Car Rally in Akita (WSR) in 1997, before fabrication of a racing bicycle. This paper describes the survey results at the above technical high schools, and the spirit as the teacher of Ofuna technical high school on joining in the race and fabrication of the solar bicycle, and the past, current and future situations. Club activities of high school students incline too toward sports such as soccer, baseball, volleyball and rugby, and are apt to keep honest cultural events and technical events at a distance. The author says that the challenge spirit to the solar car race using environment-friendly solar energy by both dedicated teachers and students of technical high schools summoned up the author`s courage. 15 figs.

Report on the fiscal 1996 research cooperation promotion project, `the research cooperation diagnosis survey`; 1996 nendo kenkyu kyoryoku jigyo `kenkyu kyoryoku shindan chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A diagnosis survey was conducted for Japan to cooperate in researching subjects on technical development in developing countries. In fiscal 1996, surveys were made on the following: (1) establishment of the industrial base (Vietnam), (2) preservation of biological diversification and the continuous utilization (Brazil), (3) fostering of the industry of automobile parts (Thailand), (4) finding out of items on environment related fields (India), (5) environmental response type system for effective use of water resource (the Philippines), (6) small size geothermal exploration in remote islands (Indonesia). (1) is research cooperation for welding technology, powder metallurgy technology, hypoid gear manufacturing technology, and iron making technology by the direct reduction method. In (2), research/development are conducted in cooperation with research institutes in Brazil on survey/identification/utilization of bioactive substances from biological resources in Brazil. In (4), an examination was made of the seeds for research cooperation in technical fields such as environment and energy. Having a strong relation with the industrial circle, SCIR is carrying out researches on aerospace, petrochemical, biology, electronics, medicines/drug, etc., which indicated fulfillment of intellectual infrastructure in India. 52 figs.

FY2000 report of the research results of medical/engineering cooperative research project, basic research on systems for minimally invasive diagnostic/treatment of circulatory system diseases, including prognostic diagnosis; 2000 nendo igaku kogaku renkeigata kenkyu jigyo, junkankikei shikkan ni taisuru yogo shindan wo fukumu teishinshu shindan chiryo system ni kansuru kiso kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The basic researches on minimally invasive diagnostic/treatment systems are conducted for circulatory system diseases, and the FY 2000 results are reported. The program for developing the heart surgery supporting manipulator includes development of the manipulator of 7 degree of freedom and fail-safe mechanisms to be incorporated in the patient-side system, and research and development of the heart motion compensation type robot system. The program for developing the diagnosis/treatment system aided by intravascular optical analysis includes development of intravascular endoscopy by the aid of LED emitting blue color of high brightness, and automatic analyzer for the in vivo vascular endothelial cell functions. The program for the minimally invasive diagnostic system includes development of superimposing system for integrating the images by the NOGA system and cine-coronary angiography. The other R and D items include artificial vascular systems to be put in the blood vessels, adhesives for a living body, suture instruments for fine blood vessels, heart surgery supporting system, based on the infrared spectroscopy, endoscopic system for the cranical bones, arterialization method, and gene-aided treatment. (NEDO)

Proposal of new seismic assessment and retrofit technology for existing buildings; Hyogoken nanbu jishin higai wo kyokun to shita kison kozobutsu no taishin shindan system

Energy Technology Data Exchange (ETDEWEB)

Yoshioka, K.; Takahashi, Y.; Seki, M.; Tanida, M.; Akiyama, T.; Hashimoto, Y. [Obayashi Corp., Tokyo (Japan)

1995-08-10

A devastating earthquake measuring 7.2 on the JMA (Japan Meteorological Agency) magnitude hit the southern Hyogo Prefecture on January 17, 1995. This earthquake, the worst in Japan since the Great Kanto Earthquake in 1923, brought great disaster and destruction to the Hanshin area and Awajishima Island. Most of the damage to concrete and steel structures occurred in buildings designed according to former building codes. Fewer collapses occurred in buildings designed under current building code that have more severe seismic requirements. Existing buildings should be assessed by their seismic potentiality, and retrofitted to escape damage in severe earthquakes such as the Great Hanshin Earthquake. New technology for assessing and retrofitting existing buildings was developed to improve resisting performance in response to severe earthquakes. Earthquake Load or motion exceeding current requirements can be supplied to assess and retrofit existing buildings if a client wants their buildings to exhibit much stronger seismic resistance. The retrofit technologies, such as a base isolation system for whole building, vibration control bracing system with steel damper, and base isolation floor system for computer equipments, can be applied to existing buildings. 11 refs., 9 figs., 8 tabs.

Development of the anomaly diagnosis system for transformers using trace constituents in oil; Yuchu biryo seibun ni yoru hen`atsuki ijo shindan hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ono, H.; Ono, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

1997-03-21

In order to complement an anomaly diagnosis system by analysis of gases in oil for transformers, the analysis/diagnosis method of trace constituents in oil was developed. Liquid-liquid solvent extraction using methanol aqueous solution as extract, and high-speed liquid chromatography were adopted to analyze decomposed products dissolved into oil by over heating as trace constituents. The relation between over heat temperature and the amount of decomposed products by over heating was studied by simulation experiment of over heat anomaly. The detectable duration of anomaly after its generation was also studied by examining the adsorption phenomenon of the thermal decomposed products onto insulating materials. As a result, the criterion of the analysis/diagnosis method was prepared by using 5-hydroxymethylfurfural as index constituent of over heating anomaly. Although furfural was also effective as index constituent, it was excluded from the index constituent because furfural is formed by deterioration of transformers even during normal operation. 2 refs., 19 figs., 7 tabs.

FY1995 fundamental study of imaging simulator for diagnostics and therapeutics using light; 1995 nendo hikari wo riyosuru shindan chiryoyo gazo simulator no kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Medical application of lasers is rapidly expanding in accordance with the development of laser technology. However, it is difficult to predict how light propagates and is absorbed by living bodies because of strong scattering of light by biological tissues. Therefore, the determination of light dose has been based on experience. This fundamental study aims to develop a imaging simulator which can predict propagation of light and its effectiveness in medical diagnostics and therapeutics. Teoretical models of light propagation in biological tissues have been constructed, and experiments have been conducted to validate the theoretical calculation. In the theoretical calculation, a three-dimensional model which simulates a human head with five layers of different tissue types. Numerical calculation has been done by using the finite element method to simulate the propagation of ultrashort pulse light, and it is shown by a computer graphics technique for the first time in the world. In the experiment, a solid phantom which anatomically and optically simulates a human head based on MRI images has been fabricated by using the optical prototyping technology for the first time in the world again. Also, we have compared the experimental results of the transmitted light through the solid phantoms with the theoretical results and have succeeded in reconstructing the tomographic images of optical properties. (NEDO)

Report on the fiscal 1995 research cooperation promotion project, `the research cooperation diagnosis survey`; 1995 nendo kenkyu kyoryoku suishin jigyo `kenkyu kyoryoku shindan chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A diagnosis survey was conducted for Japan to cooperate in researching subjects on technical development in developing countries. In fiscal 1995, surveys were made on the following: (1) recycling technology of biomass industrial waste in the tropical region, (2) small size geothermal exploration in remote islands, (3) waste water recycling system using activated carbon, etc., (4) upgrading of proofreading technology of measuring standards, (5) technology to simply set up conditions for forming engineering plastics, (6) assessment of safety of chemical substances. In (1), energy and useful matters are recovered from oil palm of Indonesia by thermal decomposition technology. In (2), a system is constructed which can effectively explore geothermal energy in remote islands in the east Indonesia. As to (3), a survey is conducted in the Philippines. (4) contributes to upgrading of length measuring standards in Thailand. (5) attempts to improve technology of forming engineering plastics. In (6), research cooperation is made for preventing environmental pollution and health damage by chemical substances from happening in Thailand and for technology for assessing safety of chemical substances which contributes to the proper use of the hazardous material law in Thailand. 28 figs.

Effects of peak shaving technologies in the residential and commercial sector; Minsei bumon no fuka heijunka gijutsu no donyu koka

Energy Technology Data Exchange (ETDEWEB)

Nagata, Y. [Kyoto University, Kyoto (Japan); Takahashi, M.; Uchiyama, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-09-01

This paper analyzes how much of the power demand could be reduced in the future by improving efficiencies of electric power utilizing appliances used in the residential and commercial sector. It discusses whether the reduction would lead to load leveling. Annual load rate in the power demand is continuing to decrease because of power demand increase in the residential and commercial sector, and increase in demand for air conditioning in summer. If a technology to improve electric appliance efficiency is proliferated to its maximum scope, the annual load rate in fiscal 2014 may be improved by 1.1 percent point. Since the improvement allows new power generation facility installation cost to be deferred, the power generation unit cost can be reduced by 0.11 yen per kwh. If a heat storage type air conditioning technology is proliferated to its maximum scope, the annual load rate in fiscal 2014 can be improved by 1.8 percent point, and the power generation cost may also be reduced. If the device efficiency improving technology and the heat storage type air conditioning technology are introduced to their maximum simultaneously, the annual load rate in fiscal 2014 can be improved by 2.5 percent point, and the power generation cost may also be reduced by 0.24 yen per kwh. If a promotion policy is taken on proliferation of a specific device efficiency improving technology having excellent economic performance by providing subsidy, the reduction amount of cumulative power generation expense will be much greater than the required subsidy amount. 10 refs., 9 figs., 22 tabs.

Effect and limitation of tuning accelerator pedal sensitivity by DBW; DBW ni yoru akuseru kando settei no koka to genkai

Energy Technology Data Exchange (ETDEWEB)

Takada, Y; Morita, S [Osaka City University, Osaka (Japan)

1997-10-01

DBW (Drive By Wire) system makes the constraint of direct connection between an accelerator pedal and the throttle valve free, so that optionally turning of throttle valve sensitivity becomes possible in automobiles driving. Reported here is the discussion of the effect and the limitation of this optionally tuning. As the former result, it became clear that the tuning method using torque signal and speed signal of the drive shaft, was easier than the method using only speed signal by PD control action. And as the latter result, upper limit was bound by the low gear ratio and tire spin. 2 refs., 11 figs.

Assessment of the environmental value of the Zichy Castle Park in Voivodeni, Romania – Brief description

Directory of Open Access Journals (Sweden)

Kovács Lóránt

2014-11-01

Full Text Available The Zichy Castle from Vajdaszentiväny (Voievodeni is located in Mure§ County, central Romania, south-west from the town of Reghin. Its constniction in classical baroque style dates back to the beginning of the X\\TH Century. The archaeological findings from the area show that Vajdaszentiväny was already populated in the Copper Age. The findings of gray dishes from the III and IV centuries were considered by Dr. Protase as indigenous Daco-Roman relics. The Roman presence here was demonstrated by residues of the hewn-stone road along the Maros River. After the Roman Age, several other populations (Goths, Slavonic peoples. Darghins and Huns settled down here. The feudal Hungarian state occupied this area around the XI Century. Several streams, terraces and old cemetery ruins demonstrate tliat the Hungarians used the region for protective purposes. The first mitten records of Vajdaszentiväny date back to 1332, when die Papal documents (Sacerdos de Sancto Johanne mention the settlement for the first time. In 1366. the name of the village was Märton-Szent-Ivän. and dunng the centuries it belonged to several old and noble families and dynasties as szentiväni Szekely. monoszlai Losonczi. Szakäcsi. the Bänffy and Dezsöfi, the Szentiväni, Butkai, Balog, Kecseti, Kerelöi, Szengyeli, Dengelegi, Fodor, vajdaszentivänyi Földväri, Koka, Piski, Järai or Järai Felsöjärai Abafäja. During the first half of the 19* Century, among former Hungarians noble owners of the village, the following can be mentioned: Count Sämuel Kemeny, Albert Horvath, Budai, Szocs (Käroly es Mihäly and Duke Löwenthäl. Later on, the village of Vajdaszentiväny became famous because of its castle, later named the “Zichy Castle,” but also because of its citizens as preservers of folk music, folk dance and folk tales.

Effect of ventilated structure on dehumidification. ; Experimental result in winter. Tsuki koho no haishitsu koka ni kansuru kenkyu. ; Toki jikken kekka

Energy Technology Data Exchange (ETDEWEB)

Sugai, T; Ozaki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering; Katayama, T; Hayashi, T; Shiotsuki, Y [Kyushu University, Fukuoka (Japan)

1912-09-01

Temperature and humidity characteristics and condensation within walls under heating and humidification were studied experimentally in winter using two test houses of conventional and ventilated structures. The absolute humidity in conventional one fluctuated depending on temperature gradient, water flux due to humidification and water adsorption onto glass wool, and accumulated water increased with humidification. That in ventilated one was also affected by dehumidification through ventilation layers. Under heating and humidification, the absolute humidity increased depending on temperature rise and water flux within walls. In conventional one, condensation was frequently observed on felt in walls and others because of accumulated humidity, while in ventilated one, humidity was kept lower within walls even under heating, because humidity in walls was discharged through ventilation layers. Condensation was also scarcely observed on waterproof moisture-permeable sheets in walls and others. 3 refs ., 39 figs 1., tab.

Effect of total pressure on sulfur capture of Ca-ion exchanged coal; Kaatsu jokenka ni okeru Ca-tanjitan no datsuryu koka

Energy Technology Data Exchange (ETDEWEB)

Lin, S.; Benjamin, G.; Abe, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

1996-10-28

In relation to coal gasification and combustion under high pressure as highly efficient coal utilization, the effect of total pressure and sintering on the SO2 capture ability of Ca-ion exchanged coal and other desulfurizing agents were studied. In experiment, specimens were filled into a small pressurized reactor to heat them under high-pressure N2 atmosphere. After the completion of combustion reaction of char at 850{degree}C, SO2, CO2 and CO gases were measured at an outlet while flowing SO2/N2. As the experimental result, all of the S content in Ca-ion exchanged coal was not absorbed by Ca content in coal during pyrolysis and combustion, resulting in discharge of 36% of the S content. Since Ca-ion exchanged coal is fast in combustion reaction, most of the S content was desulfurized by coal ash. The ash content yielded from Ca-ion exchanged coal was more excellent in SO2 capture ability than limestone even under higher pressure. In the case of CO2 partial pressure lower than equilibrium CO2 pressure for CaCO3 decomposition, the capture ability decreased with an increase in total pressure, while in higher CO2 partial pressure, it was improved. 1 ref., 7 figs., 2 tabs.

Effects of solvent and catalysts on the hydrogenolysis of alkylnaphthalenes; Alkylnaphthalene no suisoka bunkai ni okeru yobai to shokubai no koka

Energy Technology Data Exchange (ETDEWEB)

Futamura, S. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

Catalytic effects of metal and carbon materials, which promote hydrogen transfer from hydrogen donor solvents, are investigated during hydrogenolysis of benzyl-1-methylnaphthalenes (BMN) selected as a hydrogen acceptor. For the isomer distribution of BMN after the reaction, almost the same molecular ratio before the reaction was obtained independent of the presence of catalysts. Selectivity of position during the addition of hydrogen atoms from tetralin was not found. For the reaction of BMN in tetralin, 1-methylnaphthalene and toluene were obtained as products, but the formation of benzylnaphthalene was not found. As for the nuclear hydride of BMN, the trace amount formation was confirmed by gas chromatography. For the hydrogen transfer from tetralin progressed catalytically, it was found that the nuclear of naphthalene can not be hydrogenated easily. This was considered to be due to the obstruction of hydrogen transfer from tetralin by the strong adsorption of BMN on the Ni surface. 1 ref., 1 fig., 2 tabs.

Photo-irradiation effects on GaAs atomic layer epitaxial growth. GaAs no genshiso epitaxial seicho ni okeru hikari reiki koka

Energy Technology Data Exchange (ETDEWEB)

Mashita, M.; Kawakyu, Y.; Sasaki, M.; Ishikawa, H. (Toshiba Corp., Kawasaki (Japan). Research and Development Center)

1990-08-10

Single atomic layer epitaxy (ALE) aims at controlling a growing film at a precision of single molecular layer. In this article, it is reported that the growth temperature range of ALE was expanded by the vertical irradiation of KrF exima laser (248 nm) onto the substrate for the ALE growth of GaAs using the metalorganic chemical vapor deposition (MOCVD) method. Thanks for the results of the above experiment, it was demonstrated that the irradiation effect was not thermal, but photochemical. In addition, this article studies the possibility of adsorption layer irradiation and surface irradiation as the photo-irradiation mechanism, and points out that coexistence of both irradiation mechanisms can be considered and, in case of exima laser, strong possibility of direct irradiation of the adsorption layer because of its high power density. Hereinafter, by using both optical growth ALE and thermal growth ALE jointly, the degree of freedom of combination of hetero ALE increases and its application to various material systems becomes possible. 16 refs., 6 figs.

Nonlinear optical effect and excited electron dynamics of semiconductor nanocrystals; Handotai nano kessh no hisenkei kogaku koka to reiki denshi dynamics

Energy Technology Data Exchange (ETDEWEB)

Goto, T. [Tohoku University, Sendai (Japan)

1996-08-20

Investigations were given on nanocrystals of CuCl and CdTe with regard to their nonlinear optical mechanism. The experiment used a femto-second pump probe spectroscope. The experiment on CuCl nanocrystals revealed the following facts: in the case where one photon is absorbed into one nanocrystal, cascade mitigation occurs to the pair of electrons and holes, and exciters; and in the case where two photons are absorbed into one nanocrystal, exciter molecules are made via the pair of electrons and holes and the exciters. Thus, it was found that the optical nonlinearity occurs when more than two photons are absorbed into one nanocrystal, and inter-exciter interactions and formation of the exciter molecules are the physical causes thereof. The experiment on CdTe nanocrystals indicated that electrons and holes produced by laser beam are distributed instantaneously between the size-quantized discrete levels, and that temperature in the electron system drops with lapse of time. 9 refs., 6 figs.

Õpetaja tagasiside ja õpikeskkonna tajumise mõju motivatsioonile kehalises kasvatuses spordiga tegelejate ja mittetegelejate õpilaste hulgas / Andre Koka, Vello Hein

Index Scriptorium Estoniae

Koka, Andre, 1977-

2001-01-01

Uuringust, millega püüti selgitada, kuidas põhikooli õpilased tajuvad kehalise kasvatuse tunni õpikeskkonda, iseäranis õpetaja tagasiside andmist, ning millisel määral see mõjutab õpilaste sisemist motivatsiooni. Kehalise kasvatuse õpikeskkonna tajumise mõõtmiseks kasutati PELESì küsimustikku. Uurimuse käigus töötati välja küsimustik mõõtmaks kehalise kasvatuse õpetaja tagasiside andmise tajumist õpilaste poolt (PTFBì küsimustik). Küsimustele vastasid 12-15-aastased Tartu linna koolide 6. ja 8.kl. õpilased

Horn amplification at a tyre/road interface. Pt. 1. Experiment and computation; Tire/romenkan ni okeru horn koka. Jikken to keisan

Energy Technology Data Exchange (ETDEWEB)

Fujikawa, T. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

2000-01-01

Tyre/road interface noise can be amplified by a horn type space formed by the tread face of the tyre and the road. This paper is a report on studies on experiment and computation to elucidate the above phenomenon in detail. Measurement and computation were carried out on a tyre replaced with a single cylinder, whereas it was verified that the horn effect by each frequency can be calculated by BEM computation. Then, discussions were given on actual tyres combined with the BEM computation, and the following results were acquired: (1) the horn effect is small in zones of low frequencies; (2) the larger the tread width, the larger the horn effect increases; (3) the relationship between the tread width and the horn effect is governed by the ratio of the road contact width to noise wavelength; (4) the frequency characteristics of the horn effect vary largely according to whether the sound source exists in forward or rearward locations; (5) the relationship between the forward and rearward locations of the sound source with the horn effect is governed by the distance between the front and rear ends of the road contact face of the tyre; (6) the smaller the radius of the tread shoulder, the greater the horn effect; (7) tread deformation due to load applied on the tyre slightly changes the frequency characteristics of the horn effect; (8) with the sound source existing closer to the center of ground contacting width, the horn effect increases; and (9) the present study has verified the horn effect of 22 dB as the maximum. If the sound source is not present at the center of ground contacting width, the horn effect is reduced to about 10 dB, but the value cannot be ignored as the influence on traffic noise. (translated by NEDO)

Diagnosis by acetone for deterioration of breathing transformers containing an adsorbent in the insulating oil; Acetone ni yoru kyuchakuzai iri kaihogata hen`atsuki no keinen rekkado shindan

Energy Technology Data Exchange (ETDEWEB)

Awata, M.; Mizuno, K.; Ueda, T. [Chubu Electric Power Co. Ltd., Nagoya (Japan); Ota, N.; Ishii, T.; Tsukioka, H.

1997-04-20

The high-precision diagnosis for deterioration of a breathing transformer containing an adsorbent was investigated. An adsorbent (activated alumina) may be contained in oil to eliminate the deterioration product in insulating oil or the moisture. In this case, the deterioration component furfural in insulating paper is adsorbed. The concentration in furfural oil cannot be thus used for deterioration diagnosis. Acetone and furan with good relation between the adsorption characteristics for activated alumina and the insulating paper deterioration in an accelerated deterioration test can be effectively used as a new deterioration index component of insulating paper. The disassembly survey showed that acetone is valid as the index component of deterioration diagnosis. Furan is not detected in a breathing transformer, but effective in diaphragm-type and nitrogen-sealed transformers. The adsorption of acetone by activated alumina requires no correction for the change in oil temperature at about 10{degree}C. The solubility of acetone for insulating oil is 60 times at 20{degree}C as high as CO2, and the discharge rate from a breather is little (1/25). Therefore, acetone is much more excellent than CO2 as the precision of a deterioration index. 21 refs., 15 figs., 4 tabs.

Effect of additives in the baking of electrolytic materials for SOFC; SOFC yo denkaishitsu zairyo no shoseiji ni okeru tenkabutsu no koka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, H. [Kansai Electric Power Co. Inc., Osaka (Japan)

1998-09-10

A technique is discovered for improving on the baking properties of cerium oxide which is one of the solid electrolytic materials for SOFC (solid oxide fuel cell). Cerium oxide, samarium oxide, and gallium oxide are weighed, each to the specified element ratio. The element ratio of cerium is fixed at 0.8 against the other elements except oxygen, and the element ratios of samarium or gallium are caused to change. Specimens containing gallium are designated as CSGa, those not containing as SDC. SDC baked at 1600degC and CSGa (1%) baked at 1450degC are similar to each other in terms of average grain diameter. Specimens with gallium added thereto can be baked at temperatures that are lower than these by approximately 150degC. The conductivity of CSGa (0.2%) baked at 1500degC is higher than that of SDC baked at the same temperature, and is similar to that of SDC baked at 1600degC. Baking is enhanced by the addition of 0.2% gallium. In the domain where more than 1% of gallium is in presence, conductivity lowers with an increase in the amount of gallium added. The conductivity of CSGa (1%) baked at 1450degC is similar to that of SDC baked at 1600degC. 4 figs., 1 tab.

Consolidation of mechanically milled powder mixture of aluminum and quasicrystalline particle; Mechanical milling shita junkessho ryushi / aluminium gokin funmatsu no koka seikeisei

Energy Technology Data Exchange (ETDEWEB)

Yuasa, E.; Kawamura, C.; Sugiyama, T. [Musashi Institute of Technology, Tokyo (Japan)

1998-10-15

A quasi-crystalline Al65Cu20Fe15 powder prepared from alloy cast rapidly solidified by metal-mold casting, and then it was mixed to aluminum powder with various volume fractions by mechanical milling. The powder milled for above 50ks made homogeneous dispersion of quasi-crystalline phase with particle size less than 1{mu}m. The powder was hot-pressed under various conditions and then its features of consolidation were examined by the observation of microstructure and fracture strength in 3-point-bending of the compacts. When the milled powder was hot-pressed at higher compacting temperature than 673K for 3.6ks under pressure of 600MPa, the compact became to dense. Hardness of the obtained compact increases and its fracture strength decreases with increasing volume fraction of quasi-crystalline particles. Intermetallic compound Al7Cu2Fe forms in the interface of aluminum matrix and quasi-crystalline particle. 11 refs., 10 figs.

Insulation diagnosis of rotating machines for elevators by an expert system based on fuzzy inference. Fuzzy suiron wo donyushita expert system ni yoru shokokiyo kaitenki no zetsuen shindan

Energy Technology Data Exchange (ETDEWEB)

Kaneko, K.; Oshima, H. (Tokai Univ., Tokyo (Japan)); Yamada, N.; Iijima, T. (Mitsubishi Electric Building Techno-Service Co. Ltd., Tokyo (Japan))

1992-11-20

Using the data measured with the insulation deterioration diagnostic system for rotating machines for elevators, which is newly developed utilizing the past experience, an expert system which enables insulation deterioration diagnosis even by field maintenance engineers to some extent. In this system, the knowledge and experience of specialists are loaded in a personal computer as the rule for insulation deterioration diagnosis to perform insulation deterioration diagnosis by fuzzy inference and 'hypothesis-verification' type backward reasoning inference. The structured expert system is outlined. The result of insulation diagnosis by this system s compared with that made by specialists to evaluate the effectiveness of the diagnosed result of this system, and shows 84% agreement with the results obtained by specialists. It is, therefore, considered to be a highly practical expert system. 10 refs., 7 figs., 1 tab.

Catalytic effects of various catalysts in hydroprocessing of Cold Lake vacuum bottom. Cold Lake zansayu no hydroprocessing ni okeru kakushu shokubai no koka

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, S.; Yamamoto, M.; Maekawa, Y.; Kotanigawa, T. (Government Industrial Development Laboratory, Hokkaido, Sapporo (Japan))

1991-11-07

The effects of various types of catalysts were studied on hydroprocessing of Cold Lake vacuum bottom (CLVB). FeS2 [Py] of an analytical reagent grade was used as sulfide catalyst, Fe2O3(SO4)[sup 2[minus

Survey on the reduction technology of greenhouse effect gas emission from automobiles; Jidosha kara no onshitsu koka gas haishutsuryo teigen gijutsu no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The developmental trend of the reduction technology of greenhouse effect gas emission from automobiles was surveyed. Development of low pollution, energy saving and substituting energy vehicles such as electric, methanol and natural gas vehicles is in rapid progress together with performance improvement of conventional gasoline vehicles. For example, since GDI engine directly injects fuel into cylinders, it can control an air/fuel ratio at will, and reduce CO2 emission. Lean burn engine vehicle and hybrid vehicle are also under development. Performance improvement of storage batteries for electric vehicles, in particular, that combined with solar cells, and the practicability of hybrid vehicles are being clarified. Among them, the superiority of fuel cell technology in the future is becoming clear from a general viewpoint, because of its high efficiency and no CO2 emission. As methanol is produced from plants, construction of cyclic energy systems is promising. However, since low emission vehicles are expensive, some policies such as legal obligation and subsidy system are important. 30 refs., 95 figs., 26 tabs.

Effects of mechanical stimulating treatment on self-organization phenomena of materials; Kikaiteki reiki shori. Zairyo no jiko soshikia gensho ni oyobosu sono koka

Energy Technology Data Exchange (ETDEWEB)

Hida, M. [Okayama University, Okayama (Japan). Faculty of Mechanical Engineering

1999-03-31

The atoms and atom clusters around dislocation cores in crystals or surface layer deformed by mechanical energy are locally excited so as to give rise some chemical reactions and to self-organize their products into a kind of Spatial-Temporal Pattern Formation as a dissipative structure. A famous coupling phenomenon between mechanical and chemical process in solid materials must have been mechanical alloing. This report explains that various mechano-chemical treatments are powerfull method for entraining the solid system into non-equilibrium states and interesting phenomena stimulated by the mechanical self-catalysis reaction causing self-organization. (author)

Effect of activated carbon on biodegradation of organic micropollutants in water; Suichu biryo yuki busshitsu no biseibutsu bunkai ni oyobosu kasseitan no koka

Energy Technology Data Exchange (ETDEWEB)

Fukuhara, T.; Nakano, S. [Osaka Municipal Technical Research Institute, Osaka (Japan)

1997-01-10

The effect of activated carbon (AC) on biodegradation of organic micropollutants in water was investigated, using fenitrothion, phenol and aniline as the model compounds, activated sludges cultured in a mixed solution of glucose, peptone and aniline, and Rhodotorula glutinis isolated as the phenol-degradation bacterium. The following conclusions are obtained by analyzing the corrected degradation curves derived from the adsorption equilibrium relationships, oxygen consumption characteristics and observed degradation curves. Biodegradation of each compound is accelerated in the presence of AC. Non-biological degradation of fenitrothion is also accelerated in the presence of AC, its effect being more noted in biodegradation and increasing as AC quantity increases. Phenol is biodegraded by different mechanisms, depending on its initial concentration. The maximum oxygen consumption rate during the biodegradation of phenol increases in the presence of AC, conceivably resulting from enhanced bacterial activities. 5 refs., 6 figs., 4 tabs.

Measures to prevent oil pollution in oceans, and their preservation effect; Kaiyo no abura osen no boshi taisaku to hozen koka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Shinoda, T; Fukuchi, N; Fujii, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sato, S

1996-04-10

It was intended to confirm, based on various problems surrounding oil flow-out accidents, that oil fences whose use is first considered when an oil flow-out accident occurs cause oil leakage due to oil pass-through phenomenon as the largest defect in performance of oil fences. Therefore, oil fence performance was analyzed by using a simulation. Furthermore, several types of diffusion prevention and avoidance measures, and combinations thereof were evaluated by using multi-criteria analysis. It was also elucidated how recognitions on the importance of methods to prevent oil pollution differ depending on standpoints. Difference in oil flow-out prevention performance of oil fences due to variation in tidal currents was made clear by combining a diffusion simulation using the finite element method with the prevention performance of oil fences relative to the tidal currents. In areas with no good hydrographic conditions where pollution spreads rapidly, it is necessary to suppress oil diffusion by extending oil fences double or triple, and using gelling agents. 4 refs., 8 figs.

Diagnosis of aging deterioration of oil filled transformers by detection of furfural dissolved in insulating oil. Furfural ni yoru aburairi hen prime atsuki no keinen rekkado shindan no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Harigae, T.; Goto, K.; Ota, N.; Tsukioka, H. (Yuka Industries, Co. Ltd., Tokyo (Japan))

1992-06-20

The diagnosis method of aging deterioration was proposed for oil filled transformers based on detection of furfural in insulating oil. Vacuum, oxygen-added and water-added specimens of insulating paper immersed in insulating oil were thermally deteriorated at 120-180 {degree}C for 1-120 days to measure average polymerization degrees of the insulating paper and furfural contents in the oil and paper. As a result, the addition of oxygen or water accelerated forming of furfural, and the average polymerization degree considerably decreased in the early stage of heating. There was also the certain relation between the furfural content and average polymerization degree. In addition, various kinds of subjects were discussed which were required to apply these experimental results to diagnosis of aging deterioration in real oil filled transformers, and rough furfural contents corresponding to aging deterioration degrees of the insulating paper were given. As combined with a CO{sub 2} + CO method, the proposed method was expected to be more reliable. 9 refs., 8 figs., 2 tabs.

Effect of tack coat on bonding characteristics at interface between asphalt concrete layers; Asphalt concrete no sokan fuchaku ni okeru tack concrete no koka

Energy Technology Data Exchange (ETDEWEB)

Hachiya, Y. [Port and Harbour Research Inst., Kanagawa (Japan); Umeno, S. [Ministry of Transport, Tokyo (Japan); Sato, K. [Nagaoka National College of Technology, Niigata (Japan)

1997-08-20

The effect of tack coat on bonding characteristics at the interface between surface and base layers was studied for airport asphalt pavement. In a fracture behavior, shear stress is first caused by horizontal loading at the interface between surface and base layers, resulting in peeling of the layers in the case of poor bonding. Further loading under the above condition results in fracture of asphalt concrete layers by bending or tensile actions. The bonding strength between layers decreases with an increase in interval of construction between surface and base layers, while the bonding strength between layers increases with sufficient curing of tack coat. Curing for 1 hour in the daytime and 6 hours or more in the nighttime is sufficient for evaporation of water content in asphalt emulsion. The use of conventional asphalt emulsion for the sandy interface as tack coat deduces the bonding strength in the case of poor curing. Asphalt emulsion containing high-penetration rubber can improve the bonding strength. 12 refs., 27 figs., 2 tabs.

Capacidade de absorção, turbulência ambiental e desempenho organizacional: um estudo em empresas varejistas catarinenses.

Directory of Open Access Journals (Sweden)

Graziele Ventura Koerich

2015-06-01

Full Text Available Em mercados cada vez mais dinâmicos e turbulentos, as organizações dependem cada vez mais do conhecimento externo, recurso essencial no centro das estratégias organizacionais, como forma de promover a inovação e melhorar seu desempenho (Ireland, Hitt, & Vaidyanath, 2002; Zollo, Reuer, & Singh, 2002; Cassiman & Veugelers, 2006; Morgan & Berthon, 2008; Lichtenthaler, 2009. A capacidade de absorção (absorptive capacity – Acap traduz-se como um dos processos-chave de aprendizagem das organizações no que diz respeito à identificação, assimilação e exploração dos conhecimentos do ambiente (Cohen & Levinthal, 1989; Lane, Koka, & Pathak, 2006. Apesar de um considerável número de estudos empíricos ter usado a Acap, uma medida válida que incorpore essas várias dimensões ainda não foi desenvolvida (Wang & Ahmed, 2007. Lane et al. (2006 observam que a maioria dos pesquisadores tipicamente mede a Acap como simples proxies de P&D (por exemplo, Cohen & Levinthal, 1989, ignorando a variedade de suas dimensões e suas implicações para os diferentes resultados organizacionais. Não obstante, poucos estudos empíricos têm capturado a natureza multidimensional da Acap (Jansen, Van Den Bosch, & Volberda, 2005. O presente estudo verifica a influência da Acap no desempenho organizacional sob diferentes condições de turbulência ambiental. Trata-se de um estudo descritivo do tipo levantamento ou survey, com corte transversal. A população-alvo da pesquisa foi composta por empresas de varejo na região da Grande Florianópolis, com pelo menos um ano de atividades ininterruptas. Os dados foram coletados por meio de questionários autoadministrados e respondidos pelo principal dirigente das empresas, quando possível, ou por alguém responsável pelo estabelecimento. Além disso, diferentes características de moderação, como idade e tamanho das organizações, são consideradas. Os resultados a partir de 230 empresas varejistas mostram

Effect of dosing quillaia saponin on waste water from edible meat industry; Shokuniku kako kojo no haisui ni taisuru quillaia saponin no tenka no koka

Energy Technology Data Exchange (ETDEWEB)

Nagasaka, M. [Ibaraki University, Ibaraki (Japan). Faculty of Engineering

1995-12-20

For the waste water from meat processing factories, high in BOD and fat concentration, an effective treatment method was studied, wherein quillaia saponin was dosed. The waste water treatment facility of Factory K, manufacturer of ham and sausage, includes a total volume of 410m{sup 3} of aeration tanks taking in an average of 300m{sup 3}/day of waste water. The facility suffers from sludge overflows routinely, and, as a measure to cope with the situation, coagulating agents are dosed to the waste water for forced settlement. Under these circumstances, investigations were conducted to learn the effect of saponin dosing to the facility. Beginning on the 50th day of operation, saponin was dosed to the aeration tanks, and no coagulating agents were dosed to the waste water being treated by aeration. Approximately 3mg/liter of saponin was dosed to the influent waste water not treated. As the result, it was found that the BOD value decreased in the treated waste water while that in the influent untreated waste water increased as the run advanced. Even when the load grew heavier and the pretreatment was dispensed with, there was improvement in the treated water thanks to saponin dosing, which confirmed the effectiveness of saponin dosing. 6 refs., 11 figs., 3 tabs.

Improvement in visual target detections and reaction time by auditory stimulation; Shikaku shigeki ga shikaku mokuhyo no kenshutsu to hanno jikan ni oyobosu kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Akiyama, T.; Yoshimura, N. [Akita University, Akita (Japan); Takahashi, M. [Hokkaido University, Sapporo (Japan)

1998-03-01

The purpose of this study was to investigate a traffic environment that can reduce traffic accidents of elder walker. We focused on the relationship between traffic accidents and elder person`s spatial attention. In this paper, an adolescent subject`s and an elder subject`s pointing movement to a visual target was measured in three conditions. Condition 1: Only target was presented. Condition 2: Auditory stimulation was added at a location the same distance from the center as that of the targets but in the opposite direction. Condition 3: Auditory stimulation was added at the same location as the target. The targets were placed in extra working space with the distance of 1.5 meter from a subject to the targets. In adolescent subjects, results showed that in Condition 3, latency was shorter and the error rate of pointing movements was lower than in the other conditions. In elder subjects, results showed that in all Conditions, ignore ratio to peripheral targets is higher than adolescent subjects. Nevertheless, in condition 3, ignore ratio was lower than in the other conditions. These results suggest that, it is possible to draw elder walker`s spatial attention and to control spatial attention by auditory stimulation. 13 refs., 6 figs., 1 tab.

Control means of the aerodynamic vibration occured in Parallel of PC cable-stayed bridge; PC shachokyo heiretsu keburu no taifu seishin taisaku to sono koka

Energy Technology Data Exchange (ETDEWEB)

Sato, H. [Public Works Research Inst., Tsukuba (Japan); Takeda, T.; Mukai, H. [Kajima Corp., Tokyo (Japan); Oikawa, K. [SE Corp., Tokyo (Japan)

1996-01-30

In recent years, the techniques for the typical PC bridges shown in the title have been considerably developed in Japan. However, occurrence of characteristic vibrations of the parallel cables even at relatively low wind speeds are observed in many cases, for which an effective control means is inevitably required. In this report, an investigation of tests on effectiveness of 4 kinds of vibration control means carried out in a wind tunnel and its results are described. In the test, an elastic model of 3-dimension was used for 5 test cases including a case without any control means, and each case was explained and examined in detail. It was revealed that for a damping system, a considerably large damping effect was necessary to restraint the wake galloping, and the cable distance selected to be 1.5 times smaller or 6 times larger than the cable diameter was effective, and while vibration control wires were effective, the adjustment of the cable vibration frequency was ineffective. It was also pointed out that a further verification would be necessary for the latter 2 control systems as no enough experience was yet accumulated in the actual service. 13 refs., 16 figs., 6 tabs.

Global environmental benefits of industrial heat pumps (fiscal 1993); 1993 nendo koon heat pumping gijutsu ni yoru chikyu ondanka keigen koka ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

An investigational study was conducted aiming at making a quantitative grasp of effects of the spread of industrial heat pumps on energy conservation and greenhouse gas reduction and at promoting the spread. Finally, the following eight countries joined this international joint research: Canada, France, Japan, Holland, Norway, Sweden, the U.K. and the U.S. Each country share the work and expenses for the research with each other. Japan made investigational researches on the application of heat pumps to processes of the chemical industry, oil refining industry, food industry, paper/pulp industry, and dyeing/weaving industry, and on the effects of greenhouse gas reduction. As procedures taken, values up to 2010 were estimated of energy prices in each country, energy supply/demand, rates of the heat source configuration for electric power supply, etc., the heat flow of the above-mentioned process was made clear, and analyses were conducted of annual profits, energy consumption, and depreciation period in the case of adopting heat pumps. Moreover, the energy conservation amount and greenhouse effect gas reduction amount were estimated based on the result of the analyses. 69 figs., 196 tabs.

Effect of dosing quillaia saponin on waste water form marine products industries; Suisan kako danchi kara o haisui ni taisuru quillaia saponin no tenka no koka

Energy Technology Data Exchange (ETDEWEB)

Nagasaka, M. [Ibaraki University, Ibaraki (Japan). Faculty of Engineering

1995-12-20

For waste water treatment facilities of S marine products industrial complex, a demonstrative test was carried out on a waste water treatment method in which addition of biological activity promoter `quillaia saponin` and the aerobic/anaerobic method are combined. In the S marine products industrial complex, there are more than 100 plants which deal mostly with salt-preserved and boiled-fish-paste products. The plant is operated by the activated sludge method with the pretreatment pressurized floatation. The capacity of the aeration tank and concentration tank for the experiment was 2600m{sup 3} and 110m{sup 3}, respectively. The amount of saponin added was approximately 3mg/L for the amount of influent (raw waste water). The measurement items were transparency, SS, COD, BOD, n-hexane extracts (oil content), MLSS, etc. As a result of the experiment, it was found that the equipment of flocculant addition and pressurized floatation as pretreatment facilities is not necessary; the activated sludge treatment of even the waste water in which n-hexane extracts are more than 100mg/L is possible without the pretreatment; and the n-hexane extracts in the treated water is less than 2mg/L. 7 refs., 7 figs., 6 tabs.

Nonlinear effects and vortical structures in homogeneous rotating turbulence under stable density stratification; Antei seisoka ni aru kaiten ichiyo ranryu no hisenkei koka to uzu kozo

Energy Technology Data Exchange (ETDEWEB)

Tsujimura, S.; Iida, O.; Nagano, Y. [Nagoya Institute of Technology, Nagoya (Japan)

2000-02-25

The generation mechanism of the vertical vortices associated with the baroclinic instability and the effects of nonlinear term on the vortices are investigated by using both direct numerical simulation (DNS) and rapid distortion theory (RDT). Two kinds of the anisotropic flow fields are used as initial conditions. As a result, the initial anisotropy of Reynolds stresses is found to affect asymmetry of the vertical vortices. In the cases where the initial vertical velocity is set to be zero, the p. d. f. of the vertical vorticity tends to incline toward the anticyclonic side. When the vertical component of initial velocity is larger than the horizontal one, the cyclonic vortices are more enhanced. By comparing DNS and RDT, it is found that in both cases of the initial conditions the enhanced vortices of DNS are stretched in the vertical direction, which is not observed in the RDT results. This should be because the nonlinear vortex-stretching term intensifies and elongates vertical vortices in the vertical direction. The anticyclones are markedly augmented in low Prandtl number fluids, while the cyclones become dominant in the high Prandtl number case. In particular, the flow field becomes almost two-dimensionalized and Taylor columns are formed in the vertical direction in the low Prandtl number case. However, neither two-dimensionalization nor Taylor column is observed in the RDT analysis which neglects the nonlinear terms. (author)

Application of vertical electrical sounding combined with induced polarization method in ground water exploration; IP koka wo koryoshita hiteikoho suichoku tansa no chikasui chosa eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Kondo, M; Sakurada, H [Sumiko Consultants Co. Ltd., Tokyo (Japan); Suzuki, T [Hokkaido Development Bureau, Hokkaido Development Agency, Sapporo (Japan)

1996-10-01

For ground water exploration using vertical Schlumberger exploration method, measurement and analysis combined with induced polarization (IP) effect were conducted as trial. For the Schlumberger method, potential is measured at the center between potential electrodes during flow of dc current between current electrodes. In the case of vertical exploration, measurements are repeated with fixed potential electrodes by extending the distance between current electrodes. Ground water exploration was conducted using this method at Otaki village, Hokkaido. Geology of surveyed plateau consists of a basement of Pliocene tuffs and Quaternary Pleistocene sediments covering on the surface. For the results of analysis, four to seven beds were detected from the resistivity. The depth up to the lowest bed was between 25 and 85 m, the resistivity of each bed was between 9 and 8,000 ohm{times}m, and the polarizability was between 1 and 15 mV/V. Among these resistivity zones, it was judged that zones satisfying following three conditions correspond to coarse grain sediments saturated with ground water, and can be expected as aquifers; having resistivity ranging between 100 and 1,000 ohm{times}m, polarizability higher than 10 mV/V, and relatively large thickness. 11 refs., 6 figs.

Influence of strain hardening and thickness changes occurring in press forming process; Seikeiji no kako koka/itaatsu henka no buzai akkai tokusei ni oyobosu eikyo bunseki

Energy Technology Data Exchange (ETDEWEB)

Ueno, M; Hirota, K [Mazda Motor Corp., Hiroshima (Japan); Nakazawa, Y [Sumitomo Metal Industries Ltd., Osaka (Japan)

1997-10-01

Most components of the body structure are produced by press forming. This process make a uniform metal sheet into a component that have various material characteristics and thickness. This paper describes the estimation method of material characteristics and thickness changes based on the measured Vickers hardness, and the influence of these changes on the crush performance by using FE analysis. 4 refs., 12 figs., 2 tabs.

Optimum design of composite panel with photovoltaic-thermo module. Absorbing effect of cooling panel; Hikari netsu fukugo panel no saiteki sekkei. Reikyaku panel no kyunetsu koka

Energy Technology Data Exchange (ETDEWEB)

Sato, M; Kikuchi, S; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

1996-10-27

The composite panel with photovoltaic-thermo module becomes higher in energy-saving than the conventional air-conditioning system by the independent radiational heating and cooling effect obtained when the generating panel using a solar cell module is combined with the heating and cooling panel using a thermo-element module. The output of a solar cell module can be directly used because the solar cell module operates in AC. This paper reports the relation between the absorbed value and power consumption of the cooling panel, while paying attention to the cooling panel. The performance coefficient of the maximum absorbed value from an non-absorbing substance to a cooling panel is 2 to 3. Assume that the cooling panel during non-adiabatic operation is operated using a solar cell module of 800 W/m{sup 2} in solar intensity and 15% in conversion efficiency. The cooling-surface temperature difference is 12.12 K, and the maximum absorbed value of a non-absorbing substance to a cooling panel is 39.12 W/m{sup 2}. The absorbed value of the outer temperature to the cooling panel is 74.4 W/m{sup 2}, and each performance coefficient is 3.26 and 0.62. The absorbed value must be calculated for evaluation from the cooling-surface temperature difference measured directly from the cooling panel. 4 refs., 8 figs., 1 tab.

Study of recent fuel oil cost in air lines (Part 2). Saikin no airline no nenyuhi ni kansuru ichikosatsu (2); Nenryo shohi to hiyo tai koka

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Yoshikazu.

1989-03-01

Through an arrangement of published data about American air lines during 1985 through 1987, the overall expense vs. transportation fee (expense vs. effect) was studied as a main viewpoint. As a result, the fuel oil cost, even in case of wide fuselage plane, high in transportation efficiency, was high in ratio, 32 to 52% (3 to 5 times as high as that 12 to 14 years ago), and fluctuated connectedly with the oil price. While the jet fuel price fluctuated connectedly with the oil price per equal volume with 1.3 to 1.4 of price ratio. Further, the flight range ratio was recorded to be approx. 0.06 to 0.24 km/kg. While the transportation efficiency was lower than approx. 5000kg*km/kg with a wide range of overall expense, approx. 9 to 87 cents per compensative transportation ton*km. Because even a sudden decrease in transportation quantity did not decrease the overall expense, it was known to be important in management to secure the transportation quantity. 30 refs., 15 figs., 1 tab.

Burning rate characteristics of energetic CMDB propellants. Part 2. Effect of HMX addition; Ko enerugi CMDB suishin yaku no nensho sokudo tokusei ( II ) - HMX tenka no koka -

Energy Technology Data Exchange (ETDEWEB)

Aoki, I. [Nissan Motor Co. Ltd. (Japan)

1997-08-01

Burning rate and specific impulse of a solid propellant are extremely important parameters in a design of a solid rocket motor. In this study, the relations between the burning rate and the amount of energy contained in HMX-CMDB propellants wherein the amount of energy is varied by adding HMX (High Melting Point Explosive). The following results are obtained. The final flame temperature is getting higher when the amount of energy is increased by adding HMX into a double-base propellant. The higher the final flame temperature is, the lower the burning rate is. Dark zone temperature, as a physical property, is lowered when the containing amount of energy is increased by adding HMX into the double-base propellant. This is because that, when weight fraction of HMX is increased, reaction heat at burning surface decreases, and the reaction in fizz zone is getting slower. The higher the dark zone temperature is, the higher the burning rate is. 20 refs., 11 figs., 1 tab.

Effects of 4WD and ABS of safe driving on slippery roads; Tei {mu} ji ni okeru 4WD to ABS no koka to unten sosa hoho

Energy Technology Data Exchange (ETDEWEB)

Kojima, Y [National Research Inst. of Police Science, Tokyo (Japan); Takigami, K; Asano, K [Japan Safe Driving Center, Tokyo (Japan); Nagai, M [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-10-01

Effects of 4WD and ABS on safe driving were examined by brake, obstacle avoidance, acceleration, cornering and lane-changing tests on slippery road. The braking operations, used in these tests, are full, intermitted and modulated brakings. As the results of discussion, the major findings are (1) ABS is effective to shorten the stopping distance and to increase the ability of obstacle avoidance in many cases, (2) `Modulated Braking (without wheel locks)` has the same function as ABS, and (3) 4WD is effective to increase the stability while accelerating, cornering and lane-changing. 5 refs., 6 figs.

Effect of surface irradiation during the photo-CVD deposition of a-Si:H thin films. Hikari CVD ho ni yoru amorphous silicon sakuseiji no kiban hikari reiki koka

Energy Technology Data Exchange (ETDEWEB)

Tasaka, K.; Doering, H.; Hashimoto, K.; Fujishima, A. (The University of Tokyo, Tokyo (Japan))

1990-12-06

This paper shows the impact of the irradiation from an additional light source during the deposition of hydrogenated amorphous silicon by photo-CVD deposition. Using a mercury sensitized photo-CVD process from Disilan (Si {sub 2} H {sub 6}) and hydrogen, silicon was deposited. A 40W low pressure mercury lamp was applied as the light source. A portion of the substrate was in addition irradiated using an Xg-He lamp through a thermal filter. Irradiation of the substrate using only Xg-He lamp produced no deposition, since this light has a wavelength which is too long to produce the SiH {sub 3}-radicals needed for Si deposition. The additional Xg-He light source was discovered to cause an increased thickness of deposited a-Si:H film and a transmission of the band structure. The reasons of these are considered that the influence of irradiation is not limited to film thickness, but that irradiation also impacts the composition of the a-Si:H film so as to cause a reduction in the hydrogen content. 10 figs., 1 tab.

Fabrication of low cost high performance large size composite structures by electron beam curing (EBC); Denshisen koka (EBC) ni yoru tei cost koseino ogata fukugozai kozo no seizo

Energy Technology Data Exchange (ETDEWEB)

Kamimura, K.; Parrot, P.

1996-03-15

This article introduces the electron beam curing (EBC), which is high speed non-heating cure technique for the high performance resin for structures, conducted by Aerospacial Co., Ltd. In this technique, very strong electron beam and X-ray are used in response to the thickness of curing region of members, and the muzzle has energy of 10 MeV as permeation control energy and power of 20 kW as cure time control power. Advantages of fabrication of composite products by EBC is derived from the elimination of exoergic and heating curing processes and the local cure molding. For the EBC, the residual stress is not generated, the size is stable, the insertion of different materials is easy without mismatch of thermal expansion between the composites and metals, the homogeneous bridge can be obtained to stabilize the material quality, the processing time can be shortened, it is suitable to mass production, and the cure of products can be controlled. About 30% to 40% of the cost of products can be reduced. 1 ref., 6 figs., 1 tab.

Effect of applied synthetic auxin on root growth in plantlet propagation by cuttage and tissue culture; Sashiki to soshiki baiyo ni okeru gosei auxin rui no shiyo koka

Energy Technology Data Exchange (ETDEWEB)

Shoji, K; Yoshihara, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-12-01

The effect of synthetic plant hormone 4-C1-IAA and TFIBA on root growth in plantlet propagation was clarified by the cuttage and the issue culture of strawberry seedling production. A periwinkle, vine, and azalea are the effect of 4-C1-IAA on root growth, and a promotion effect was recognized for rooting and root elongation. The concentration of 4-C1-IAA in which the growth promotion effect of a root most appears varies depending on the species of a plant. The concentration of a periwinkle was 20 ppm, and that of an azalea was 2000 ppm. The growth promotion effect of a root in 4-C1-IAA and TFIBA was compared with IBA for an azalea. The result showed that 4-C1-IAA is the same in the effect as IBA and that TFIBA is higher than for IBA. The growth of a vine`s terminal bud was promoted by the effect of TFIBA on root growth, and the callus occurring when IBA was treated was not formed. The rooting of a strawberry was promoted by the effect of TFIBA on root growth. The combined use of TFIBA and BA promotes the growth of a side bud and forms a multi-bud plant. However, rooting was inhibited. The callus caused by the effect of BA on root growth could be suppressed through the combined use with TFIBA. 6 refs., 7 figs., 2 tabs.

Impact of technology diffusion on economic growth and international competitiveness. Empirical evidence for four East Asian countries; Gijutsu hakyu no koka to Asia keizai no seichoryoku, yushutsu kyosoryoku

Energy Technology Data Exchange (ETDEWEB)

Hoshino, Y.; Sakurai, N.

1999-06-01

Asian economies hit by the currency crisis in 1997 are still in struggle to recover their growth and to boost again their exports. Although several short-term policy measures to stimulate the demand- side of the economy is certainly necessary, in a longer-term perspective, the key to real recovery would exist in their ability to absorb foreign technologies through trade and/or FDI, as stressed by recent new theories of growth and trade. This paper examines empirically the role of technology diffusion from advanced countries to total factor productivity (TFP) and export competitiveness in four major East-Asian countries: Korea, Singapore, Malaysia and Indonesia, three of which were seriously damaged by the currency crisis. Our major findings are summarized as follows. First, we found that technology acquisition from abroad is quite important for TFP growth of most industries in Asia, in particular for two ASEAN countries (Malaysia and Indonesia), while such productivity impact from foreign technology was relatively small for Korea and Singapore. Second, the impact of technology diffusion was much larger in that through trade than in that through foreign direct investment. Some FDI practices to preclude technology access for developing countries might explain such weaker role of FDI on TFP. Third, the nexus between TFP and export competitiveness was surely positive, in particular for industries of high export performance. However, the magnitude of impact was relatively small in Korea, in spite of its overwhelming productivity performance. (author)

Survey and research on the effects of technological development. Annex (Tables of technology-related data); Gijutsu kaihatsu no koka ni kansuru chosa kenkyu. Bessatsu (gijutsu kanren data list)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Compiled into a report are the data about trends in Japan's research and development efforts broken down by industry covering a period of 1960-1980. The data items are quite versatile, including the number of companies engaged in researches and their rates, number of employees, total sales volume, profits through business, number of employees related to researches, number of dedicated researchers, number of dedicated researchers per 10,000 employees, disbursement of in-house research expenses, rate of personnel expenses to in-house research expenses, rate of disbursement of in-house research expenses to total sales volume, rate of disbursement of in-house research expenses to profits through business, disbursement of in-house research expenses per company, disbursement of in-house research expenses per dedicated researcher, in-house research expenses broken down by purpose (basic research, applied research, research for development), component ratio (basic research, applied research, research for development), number of dedicated researchers per speciality (total number, mathematics and physics, chemistry, biology, geology, engineering, civil engineering and construction, machinery and ship and aviation, electricity and communication, mining and metallurgy, textile, agriculture and forestry, fishery, stock-breeding and veterinarian, medicine and dentistry, pharmacy), number of technologies exported, total sum of export, etc. (NEDO)

Enhancement of condensation heat transfer using electric field. Effects of wire-electrode coating; Denba ni yoru gyoshuku netsu dentatsu no sokushin ni kansuru kenkyu. Wire denkyoku no hifuku koka

Energy Technology Data Exchange (ETDEWEB)

Chu, R. [Gifu University, Gifu (Japan). Faculty of Enginering; Nishio, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Tanasawa, I. [Nihon University, Fukushima (Japan). College of Engineering

2000-08-25

In the present paper, an attempt is made to develop an effective EHD enhancement technique for condensation heat transfer of steam around a horizontal finned tube. The main idea in the present study is to reduce the power consumption by using a partially coated electrode, and the experimental data of heat transfer coefficients and flooding angles are presented. The result indicates that, by using such an electrode, the enhancement ratio keeps almost the same level with that of a bare electrode but the power consumption can be markedly decreased. Within the present experimental range, the condensation heat transfer coefficient on the finned tube with the partially coated electrode reaches a value about 3 times larger than that without electrode. In addition, a model in presented for the EHD effect on the flooding angle and it is confirmed that the prediction from the model is in good agreement with the experimental data. (author)

Effect of intermolecular cohesion on coal liquefaction. 3. Reactivity of oxygen methylated coal; Sekitan teibunshika hanno ni okeru bunshikan gyoshuryoku no koka. 3. O-methyl ka tan no hanno tokusei

Energy Technology Data Exchange (ETDEWEB)

Sasaki, M.; Nagaishi, H.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

1996-10-28

The reactivity of oxygen methylated coal was studied to control hydrogen bond in bituminous coal liquefaction and intermolecular cohesion such as van der Waals force. In experiment, crushed and dried Illinois coal of 100mesh or less was used as specimen, and oxygen methylated coal was prepared by Liotta`s method using tetrabutylammonium halide. Coal liquefaction was conducted in an electromagnetic agitation autoclave using tetralin solvent under initial hydrogen pressure of 100kg/cm{sup 2} while heating. The molecular weight distribution of the products obtained was measured by gel permeation chromatography (GPC) analysis. The experimental results are as follows. The effect of intermolecular cohesion in bituminous coal on the reactivity is mainly derived from decomposing reaction from preasphaltene to oil. Yields of oil fraction by methylation increase corresponding to release of intermolecular cohesion. Since the thermal release is promoted with temperature rise, the difference in yield due to different treatments decreases. 5 refs., 3 figs., 1 tab.

Report on evaluation on endocrine disturbing effect of chemicals and development of test methods; 1999 nendo kagaku busshitsu no naibunpi kakuran koka ni kansuru hyoka oyobi shikenho no kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With regard to endocrine disturbing effect being the new deleteriousness of chemicals, data were collected and evaluated by using the existing testing methods, data were collected by using the screening test, the testing methods were developed, and international investigation was carried out to establish the risk evaluation methods. In the evaluation by using the existing test methods, seven substance groups deficient in deleteriousness data qualitatively and quantitatively were given reproduction toxicity tests to evaluate availability of the endocrine activity. Development of the screening test method has been carried out by participating the validation test by OECD to make the uterotrophic assay method and the Hershberger assay method a test guideline having international matching property. International investigations to establish the risk evaluation were executed on the molecular mechanism of nuclear receptors, the chemical, metabolic and environmental behaviors of endocrine active substances, the effects of the endocrine active substances on experimental animals and human, the utilization thereof for risk assessment in human, and the effects of endocrine disturbance acting substances in wildlife species. (NEDO)

Effect of insolation forecasting error on reduction of electricity charges for solar hot water system; Taiyonetsu kyuto system no denki ryokin sakugen koka ni oyobosu nissharyo yosoku gosa no eikyo

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)

1996-10-27

A solar hot water system can be economically operated if inexpensive midnight power is purchased to cover the shortage of solar energy predicted for the following day. Investigations were conducted because error in insolation prediction affects the system operation and electric charge reduction effect. The target temperature of the heat accumulation tank at every predetermined time point is calculated on the previous evening in consideration of predicted insolation so that the water will be as hot as prescribed at the feeding time on the following day. Midnight power is used for uniform heating to attain the target temperature for 7 o`clock on the following morning. The uniform heating continues from 8 o`clock to the feeding time, this time using solar energy and daytime power to attain the target temperature. Accordingly, the division between the midnight power and daytime power is determined in view of the target temperature for 7 o`clock on the following morning, which target temperature is so set that the charge will be the minimum by optimizing the allocation of the above-said two. When the insolation prediction error rate is beyond 30%, the electric charge grows higher as the rate rises. But, when the rate is not higher than 30%, the charge is little affected by a rise in the rate. 5 refs., 10 figs., 1 tab.

Evaluation on diminishing effects of DNA damaging potential by humic substances using the bacillus subtilis rec-assay; Karekusakin rec-assay wo mochiita fuminsan ni yoru DNA sonshosei kaizen koka no kento

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H.; Takigami, H.; Shimizu, Y.; Matsui, S. [Kyoto University, Kyoto (Japan). Faculty of Engineering

1998-05-22

Antimutagenic effect of humic substances has been reported by various investigators. In this research, the diminishing effect of DNA damaging toxicity by humic acid was evaluated for the influent and effluent of activated sludge tank receiving municipal wastewater and several DNA damaging chemicals (e.g., pyrene, 1-aminopyrene and benzo(a)pyrene) using Bacillus subtilis rec-assay. The diminishing effect was not apparent for influent but observed in the effluent. Among the DNA damaging chemicals, the DNA toxicity was effectively suppressed by humic acid for pyrene and benzo(a)pyrene. However, the effect was relatively smaller for 1-aminopyrene. 19 refs., 6 figs., 6 tabs.

Fiscal 1997 survey report on technology to reduce the amount of greenhouse gas emitted from automobiles; 1997 nendo chosa hokokusho (jidosha kara no onshitsu koka gas haishutsuryo teigen gijutsu no chosa). 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to intelligent transport systems (ITS), the paper views the outline of the R and D and diffusion in Europe, the U.S. and Japan and trially estimated the effect of reduction in greenhouse gas, and worked out visions/scenario for diffusion of ITS. As developmental fields contributing to reduction in greenhouse gas, the following were taken up: 1) AVCS (advanced vehicle control system), 2) automatic rates receiving system, 3) traffic management, 4) plans of operation management/allocation of commercial cars, 5) modal shift of the material flow, and 6) public traffic in passenger transportation. As effects by developmental field, 1) and 5) are especially effective. 4) is promising because of its easiness in introduction, and 2) is also a promising technology as a tool to introduce an electronic road pricing system on general roads in future in addition to the effect of reducing heavy traffic by its introduction to expressways. However, the higher the service level on the facility side becomes, the more the traffic demand amount becomes. By how to introduce ITS, it possibly occurs that improvement of the situation will not be made at all on the future vehicle traffic system. 38 refs., 42 figs., 52 tabs.

FY 2000 report on the basic study/survey on the policy mix for reducing the greenhouse gas emissions; 2000 nendo onshitsu koka gas haishutsu sakugen no policy mix ni kansuru kisoteki kento

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on policies for reducing the greenhouse gas emissions. For Japan to meet the emission reduction targets stated in the Kyoto Protocol, it is necessary to examine in detail what the most desirable policy measures should be for each sector. In this context, it is also essential to determine particular features of the various policies that may include action plans, environment taxes, and emission trading in addition to conventional regulations and subsidy measures, and to assess their anticipated effects and problems. After examining the policies adopted by various countries to reduce greenhouse gas emissions, this study has attempted to identify the merits and demerits of the various emission reduction policies and to present a systematic account of progress achieved in Japan during basic investigations into this issue. This reports provides a systematic overview of the action plans adopted by the other major countries to prevent global warming and makes a comparative study of the contents of the policies that have been introduced by these countries; identifies the arguments raised in the overseas debates on the effects and problems of global warming prevention policies, and attempts to put the arguments into some systematic order; examines the statuses of the current progress made by various countries with regard to methane and N{sub 2}O emission reduction policies, and discusses the related problems; gives a systematic account of how the policy options are being scrutinized by the government as the base for studying the policy mix for Japan; and examines statuses of the current progress made by Japan with regard to methane and N{sub 2}O emission reduction policies. (NEDO)

Condensation of refrigerant CFC 11 in horizontal microfin tubes. Proposal of a correlation equation for frictional pressure gradient; Reibai CFC11 no microfin tsuki suihei kannai gyoshuku. Atsuryoku koka no jikkenshiki no teian

Energy Technology Data Exchange (ETDEWEB)

Nozu, S [Univ. of Okayama Prefecture, Okayama (Japan); Katayama, H [Mitsubishi Chemical Co., Inc., Tokyo (Japan); Nakata, H [Daikin Industries, Ltd., Osaka (Japan); Honda, H [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-09-25

Local heat transfer and pressure drop measurements were made during condensation of CFC 11 in microfin tubes. A smooth tube and two microfin tubes with different fin dimensions were used. Flow observation study with use of an industrial bore-scope revealed that the condensate swirled along the grooves, and a thick condensate film covered fins in the lower part of the tube in the low quality region. Static pressure gradients in the microfin tubes were up to 70 percent larger than that in a smooth tube. A correlation equation for the local frictional pressure gradient was derived, in which the effect of refrigerant mass velocity was introduced on the basis of the flow regime consideration. The measured frictional pressure gradient data were found by the present method to have a mean absolute deviation of 8.3 percent. 24 refs., 11 figs., 3 tabs.

Study on reduction of consumption and peak demand of electric power used in residential houses with solar heating and PV systems; Solar house no fuka heijunka to energy sakugen koka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Udagawa, M.; Endo, T. [Kogakuin University, Tokyo (Japan)

1994-12-08

A model house was simulated to reduce the consumption and peak demand for the photovoltaic power generation system, and solar heat air heating and hot water supply system in the solar house. As a type of construction, both wooden construction and reinforced concrete (RC) construction were selected with a total floor area of 125m{sup 2}. All the rooms were equipped with an air conditioner by heat pump from the air thermal source. A solar heat floor heater was simultaneously installed on the first floor. The hot water supply load was 4.8MWh per year. A commercial grid-connected on-site system was applied to the photovoltaic power generation with a 20m{sup 2} wide monocrystalline Si solar cell panel. As for the fluctuation in power load, the peak at the time of rising is more reduced in the RC house than in the wooden house, because the former is smaller in temperature fluctuation than the latter during the intermittence of air conditioning (as per the specified operational schedule). Therefore, the power is more leveled off in the former than in the latter. Between both, difference was hardly made in energy consumption per year. The ratio of dependency was 47% upon the photovoltaic power generation system, while it was 50% and 77%, under the air heating power load and hot water supply power load, respectively, upon the solar heat air heating and hot water supply system, so that both systems were considerably effective in saving the energy. 5 refs., 7 figs., 1 tab.

Effect of heat-insulating wall on input energy of a photovoltaic/solar/air-heat system for a residence; Jutaku no kodannetsuka ni yoru taiyoko netsu/taiki netsu system no donyu energy sakugen koka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan)

1996-10-27

A proposal was made to introduce a photovoltaic/solar/air-heat system which positively utilizes natural energy in order to curtail consumption of fossil energy, corroborating that the system has greatly reduced energy input in the primary energy level in a house. This paper examines the effect of curtailment of energy input in the case of reducing the load of air conditioning through the high heat insulation of a house. The energy input was evaluated by calculating additional equipment energy needed newly for the high heat insulation. The system performance and the energy load varied greatly depending on weather conditions. The subject system consisted of solar cells, inverter, heat concentrator, heat storage tank, heat pump and gas hot-water supply device. The thickening of the insulation sharply reduced heating load in the house, thereby decreasing fuel energy substantially. An insulation material of 100mm thick was capable of reducing energy input by 16-23% compared with that of 50mm thick. 5 refs., 5 figs, 3 tabs.

Measuremental analysis of thermal performance of direct gain houses in Kanto district. Effects of thermal mass and caves; Kanto chiho ni tatsu direct gain jutaku no netsuseino jissoku. Netsuyoryo to hisashi no koka

Energy Technology Data Exchange (ETDEWEB)

Inoue, K; Sunaga, N; Muro, K [Tokyo Metropolitan University, Tokyo (Japan)

1996-10-27

The thermal performance of direct gain passive solar houses was measured. Mr. M`s two-storied RC residence with double glazing windows and thermal storage floors, walls and ceilings of brick or concrete was provided for measurement. Its double eaves of the south window and both SE and SW overhanging exterior walls play a role in sunshade. Mr. I`s two-storied wooden residence with thermal storage RC floors and brick walls, and no eaves of the south window and no overhanging exterior walls was also provided. The summer and winter measurement results were in complete contrast between the residences. In summer, large thermal mass and eaves of Mr. M`s residence were effective, while in winter, small thermal mass and no eaves of Mr. I`s residence were effective. The following ideas are important in design from the viewpoint of indoor thermal environment: a movable sunshade for taking in solar radiation as much as possible in winter, well-balanced arrangement of thermal storage parts with suitable thermal mass corresponding to movement of the sun, a large screen door for cross ventilation in summer, and a night insulation shutter for reducing heat loss in winter. 2 refs., 10 figs., 1 tab.

Report on the FY 1999 medical/engineering joint research project. Developmental item: 'Fundamental research for minimally invasive/super selective localized diagnosis and treatment system'; Teishinshu kokando sentakuteki kyokusho shindan chiryo ichigenka system no kiban kenkyu 1999 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The fundamental research was started of a total system for the minimally invasive diagnosis/treatment to cope with the diseases of brain/heart blood vessel system and malignant tumor which are increasing in the aging society, and the development of application of the system was started. The results of the FY 1999 study were reported. In the R and D of the technology for an up-grade/multi-functional catheter, the following were carried out in the design of a micro-diameter catheter for carrying out the total diagnosis/treatment: study of infrared radiation measuring and fluorometric measuring methods, study of the specifications required for the catheter presumed of the gene introduction method by water jet system, study of 2 and 3 {mu}m synchronous oscillation fiber laser which is suitable for optical micro-operation, etc. The information/knowledge in design were obtained. Further, in the basic research on high-sensitivity texture property diagnosis using optical spectrometry, experimental studies were started on the early diagnosis technology by infrared spectroscopy and lymphonodus metastasis diagnosis technology. A study was also started of gene therapy technology by diseases which can be diagnosed/cured using catheter. (NEDO)

Studies of initial stage in coal liquefaction. Effect of prethermal treatment condition with process solvent to increase oil yields; Ekika hanno no shoki katei ni kansuru kenkyu. Sekitan no maeshori joken to yozai koka

Energy Technology Data Exchange (ETDEWEB)

Shindo, T.; Komatsu, N.; Kishimoto, M.; Okui, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. ltd., Tokyo (Japan)

1996-10-28

Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogen transfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of THF-insoluble using high hydrogen-donor solvent and/or by adding catalyst. It was also found that the use of high hydrogen-donor solvent and highly active catalyst at the stage of prethermal treatment before the successive liquefaction was effective for improving the HS yield, i.e., liquefied oil yield. 2 refs., 5 figs., 1 tab.

Introduction effect of a load levelling system in an electric power system with a photovoltaic and wind system; Taiyoko/furyoku hatsuden wo donyu shita denryoku keito ni okeru fuka heijunka shisutemu no donyu koka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

1998-12-05

Introduction effect of load levelling system by a battery in an electric power system by a battery in an electric power system with a PV and wind system is investigated. Charge and discharge power of the battery are determined from a load curve and every hour data of PV and wind output. Annual cost of the power system is calculated from the generating power and the capacity of each source via the installed utility capacity and the capacity factor. It is found that (1) the battery system reduces the maximum demand and improves the load factor, (2) the cost effect of the battery system when introducing the PV system is higher than that when introducing the wind system. (author)

Degradation and stabilization of coal derived liquid. (IV). ; Effect of alcohol on coloration of coal derived light oil. Sekitan ekikayu no anteika. (IV). ; Sekitan ekikayu no chakushoku yokusei ni oyobosu alcohol no tenka koka

Energy Technology Data Exchange (ETDEWEB)

Ukegawa, K.; Matsumura, A.; Kondo, T. (National Research Institute for Pollution and Resources, Tsukuba (Japan)); TAhara, N. (Nitto Denko Corp., Osaka (Japan)); Nakamura, E. (New Energy and Industrial Technology Development Organization, Tokyo (Japan)); Niki, E. (The University of Tokyo, Tokyo (Japan). Research Center for ADvanced Science and Technology)

1990-01-20

In order to improve the color stability of a coal derived light oil, the effect of hydrotreating and various additives has been studied. The color stability has been evaluated through measuring changes in absorbance by flow-cell spectrophotometer. Following results have been obtained: The color stabilities of hydrotreated coal derived light oils were improved remarkably with increasing hydrotreating temperature and pressure. Mild hydrotreating made the color stability of the coal derived light oil much better than the fuel oil, even though the nitrogen removal was very small. Phenolic compounds additives could not improve the color stability of the coal derived light oil. Alcohol, especially methanol, made the coloration rate of the coal derived light oil small to a great extent, on account of hydrogen bonding between methanol and nitrogen compounds in the fuel oil. 4 refs., 4 figs., 3 tabs.

FY 1998 annual report on the survey and research on methodology for estimating reduced amounts of greenhouse effect gas emissions; Onshitsu koka gas haishutsu sakugenryo santei hoho ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Although introduction of Joint Implementation (JI) and Clean Development Mechanism (CDM) have been adopted in the COP3, the details of how to set up the baseline for calculating the emission reduction amounts have not been established. This survey/research project has sorted out various concept menus for setting the baseline, verify each menu, and positively propose the methodology in an international arena, in which merits and demerits involved in simplified approaches, which try to simplify the works for setting the baseline, are analyzed, and their effectiveness is investigated. At the same time, both FCCC AIJ and NEDO AIJ projects are analyzed, to understand characteristics of baseline-setting method adopted by each project. There are many project types, to which direct application of any simplified approach is difficult. It is therefore realistic to analyze the situations case by case for the time being, and pursue for possibility of standardization of the baseline-setting methods after sufficient experience and data are accumulated to allow classification of the projects by common features. (NEDO)

Report on fundamental surveys for such as cases and effects in relation with development of new energy technologies in fiscal 1999; 1999 nendo shin energy gijutsu kaihatsu ni kakawaru jirei koka nado kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the fundamental surveys in fiscal 1999 on cases and effects in relation with development of new energy technologies. Among the projects having been performed by NEDO in commemoration of the 20th anniversary of the NEDO foundation, the economic and social situations in the times in which the projects have been carried out with the focus placed particularly on new energies were put into order and analyzed to make clear the positioning of the project significance in the nation's energy policies. In addition, the roles of NEDO were recognized afresh to use them as the fundamental materials to serve for the future policy development. For the past thirty years before and after the oil crises, the time division that can be used universally for the project evaluation was established, based on the trends inside and outside the country, social currents, related indexes, and the status of development execution. Work hypotheses were presented regarding the basic conception in the evaluation, specific evaluation viewpoints, and their contents. Based on the hypotheses, three subjects were taken up as representative cases, that is, photovoltaic power generation, coal liquefaction, and phosphoric acid type fuel cell technology development. Time points that are considered as the important turning points were specified to give evaluations at respective turning points. Analyses were also made on decision making factors for project planning, continuation, direction change, suspension, and completion. (NEDO)

Data acquisition and analysis of passive solar cooling effects by storage of out door air in the middle of the night; Shin'ya gaiki chikurei ni yoru shizen reibo koka no jissoku to kaiseki

Energy Technology Data Exchange (ETDEWEB)

Inagaki, H.; Kasutani, A. [Komazawa Womens Junior College, Tokyo (Japan); Koizumi, H.

1998-12-05

Passive cooling by storing coolness of out door air in the middle of the night in rock bed is realized by air type solar system without any additional equipment. The advantage of the passive cooling is confirmed with measuring performance of the passive cooling effect of air type solar system equipped in our Komazawa Womens Junior College last year. (author)

FY 2000 Medical/engineering cooperative research project. Basic research on high-sensitivity gene-aided diagnostic systems for cancers, based on free DNA in blood; 2000 nendo kecchu yuri DNA ni yoru gan no kokando idenshi shindan system ni kansuru kiban kenkyu jisseki hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The research and development project is conducted to develop new methods directly related to early discovery of potential cancer patients, and the FY 2000 results are reported. The FY 2000 efforts are directed to improvement of intra-Alu-PCR method as the superhigh-sensitivity quantitative method, almost established in the previous fiscal year, to have higher reliability and simplicity suitable for automatic diagnosis. It is concluded that (there is no difference of significance between normal persons and cancer patients in free DNA concentration in the blood, determined by the Boyle/intra-Alu-PCR method), but this method is confirmed to be useful for prognostic monitoring of the patients who have the marrow or peripheral vessel cell transplant. Detection of qualitative gene abnormality of DNA in the peripheral vessels is investigated using the K-ras, p53 gene. Certain results are obtained by the MSA method for the former, and by the newly introduced WAVE DNA fragment analysis system for the latter. However, there are still a number of problems to be solved before these methods are applicable to screening for general medical examinations. The research on the (analysis of gene abnormality of cancer itself) has made a notable progress. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Research and development of smart catheter for omnidirectional diagnosis; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Zenhoi shindan smart catheter no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The aim is to develop a highly reliable device for detecting pathological developments deep inside the body by combining the pulse compression technique used in high performance radars and a quartz fiber. The project also aims to develop a system which, when compared with the conventional method, is capable of higher resolution at a short range and of reaching farther for the same resolution level. To be contrived for the development of a diagnostic catheter which combinedly uses the ultrasonic pulse compression and imaging technology and an optical picture system are a pulse signal reflection mirror for taking in ultrasonic picture data on the front and the sides in the lumen, an ultrasonic micromotor for rotating the mirror, and a high efficiency ultrasonic transducer similar in size to the waveguide for transmitting ultrasonic pulses to a quartz waveguide from outside the body and for receiving reflected signals. An effort is simultaneously exerted to make the diameter smaller of a quartz waveguide to be built in the catheter to provide a signal passage for the ultrasonic imaging system and the optical picture system for the realization of a catheter tip smaller and thinner as a whole. A study is made about a mechanical-electronic control system for easy luminal insertion. (NEDO)

FY2000 report of the research results on medical/engineering cooperative research project, fundamental research for minimally invasive/super-selective localized diagnosis and treatment; 2000 nendo igaku kogaku renkeigata kenkyu jigyo teishinshu kokando sentakuteki kyokusho shindan chiryo ichigenka system no kiban kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The research and development efforts are made for super-selective localized diagnosis and treatment and simultaneous observation of the treatment results at the catheter edge point, based on the molecular biology and gene engineering methods, and the FY 2000 results are reported. The program for investigating the catheter hardware designs include the diagrammatic evaluation of a multi-lumen multi-functional laparoscope and pancreatoscope for localized diagnosis and medical treatment. The program for development of diagnostic technology leads to development of double staining of cancer cells and macrophage, which allows the in vivo analysis of the cell-to-cell interactions. The program for studying the technology related to affective genes which can be diagnosed and treated by a catheter includes cloning of genes for therapy of chronic glomerular nephritis and adrenal neoplasm, and those for liver regeneration. The program for method of local delivery of genes includes studies on therapy of metastatic cancer of lymph node using liposome and adenovirus as a gene carrier, and on pulse laser delivery for local and efficient delivery of the genes. (NEDO)

Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Intravascular 3D ultrasound imaging system for supporting less invasive diagnosis; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Shindan shiengata choonpa kekkannai sanjigen imaging system

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

An ultrasonic probe with its point fine is navigated in blood vessels and body cavities by 3-dimensional ultrasonic signals (with the oscillator driven by transmission from a catheter for position detection) for the acquisition of accurate 3-dimensional ultrasound images in a less invasive way. The transmission and reception circuits are provided with circuits for ultrasound tomographic images and for navigation. Trial units are fabricated and tested for transmission waveform and reception performance. The scanner is rotated for the acquisition of intravascular 3-dimensional radial images. The scanner rotating rate is set at 30 rps for the scanner performance not to be affected by heartbeat and the rate is controlled by the observation unit which changes voltage for the control. The 3-dimensional display software program, thanks to the navigation function of the external probe, detects the external probe position relative to the small-diameter probe for the construction of accurate 3-dimensional images. Specifications for a total system, which makes full use of a navigation function, are compiled, consisting of a small-diameter probe and a body surface real-time 3-dimensional display. (NEDO)

Customers` response to residential peak-activated pricing. Evidence from a Japanese experiment; Peak taio ryokinka ni okeru kateiyo juyoka no fuka chosei kodo no bunseki. Kansetsu fuka seigyo jikken data wo mochiita kakaku koka no sokutei

Energy Technology Data Exchange (ETDEWEB)

Asano, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-10-01

Demand side management through a pricing mechanism, that is the indirect load control was experimented to analyze the pricing effect. When power consumption in indirect load control groups is compared between peak time band in weekdays in summer and off-the-peak time band, the power is less consumed when price gap is set than in a uniform charge time. When more number of persons is in home in daytime, room cooling is used in daytime including the peak band to adjust the demand. The substitution elasticity in price between demands in the peak time band and the off-the-peak time band is from about 0.06 to 0.07, which cannot be ignored. If the peak price is increased by four times, the demand in the peak band can be reduced by about 0.15 kW (when average power demand per household is assumed 0.75 kW). For room cooling devices, the first device is often installed in a living room and the second and further units in individual rooms such as bed rooms. The more the number of device, the higher the possibility that the use time band is outside the peak time band. This indirect load control experiment is a field test related to the peak-activated pricing for small power users, by which the users` behavior against the pricing effect was identified quantitatively. 5 refs., 1 fig., 8 tabs.

Simulation study on reduction of peak power demand and energy consumption in residential houses with solar thermal and PV systems; Taiyo energy riyo jutaku no fuka heijunka oyobi energy sakugen koka no simulation ni yoru kento

Energy Technology Data Exchange (ETDEWEB)

Endo, T. [Yokohama City Office, Yokohama (Japan); Udagawa, M. [Kogakuin Univ., Tokyo (Japan). Faculty of Engineering

1995-11-20

In this study, taking the all factors involved in the energy consumption in residential houses as subjects, the effectiveness of the solar PV system and solar thermal utilizing system in residential houses has been studied by simulating a model residential house considering the improvement of the residual environment in the future. Therefore, a model residual house is assumed, 18 kinds of combinations of construction style, cooling and heating type and solar energy utilizing form are assumed and year round simulation is carried out. The conclusions obtained by the simulation are as follows. The energy consumption in residential houses may decrease greatly by using a solar hot water supplying system. If combined with a solar PV system, the energy consumption in one year is about 8.7 to 9.7 MWh. The combined use of a solar thermal utilizing system and a PV system is more effective to reduce the second-time energy in comparison with the PV system only. 36% of the space heating energy consumption may be decreased by using the solar space heating system, but the decrease effect of the energy consumption of the solar space heating system is smaller than the solar hot water supplying system. 12 refs., 26 figs., 3 tabs.

Report on the FY 1999 medical/engineering joint research project. Basic research on a high-sensitivity gene diagnosis system for cancer by free DNA in blood; 1999 nendo kecchu yuri DNA ni yoru gan no kokando idenshi shindan system ni kansuru kiban kenkyu jisseki hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A 3-year (FY 1999-FY 2002) research plan titled 'The basic research on a high-sensitivity gene diagnosis system for cancer by free DNA in blood' was worked out and the study was started. The plan is as follows. It is confirmed that the quantitative study of peripheral blood free DNA becomes the information useful for early finding-out of cancer carriers, and the reliability and limits are made clear. By widely searching for gene anomaly of cancer itself, it is confirmed that it is possible to diagnose anomaly in quality of genes in peripheral blood free DNA. For those purposes, technology is developed for high-sensitively detecting/quantifying free DNA of peripheral blood, etc. and further detecting anomaly of the genes comprehensively, and the medical/engineering joint research is conducted to realize the early diagnosis of cancer. In FY 1999, the following studies were started using detection/analysis technology mainly by polymerase chain reaction (PCR): development of high-sensitivity detection technology of free DNA, development of high-sensitivity detection technology of gene anomaly, study of the cancer-origin gene anomaly, etc. (NEDO)

Research on the evacuation readiness of bus crews and passengers. Effect of an easy-to-understand emergency exit display; Bus no jikoji no join jokyaku no dasshutsu yoisei ni kansuru kenkyu. Hijoguchi hyoji kaizen koka no chosa

Energy Technology Data Exchange (ETDEWEB)

Shiosaka, Y. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

1996-10-01

Answers collected from interviews show that very few of the bus passengers know how to open emergency exits and that such exits are floored too high, and dangerous, for aged people and children. In this paper, the emergency exit display is picturized in conformity with the ISO6309-provided evacuation signs, and the Chinese characters on the sign are replaced by `hiragana` characters for the youngest of the elementary school children, unable to Chinese characters, to read with ease. The cover is removed from the lever for opening the emergency exit so that the lever may be seen from the outside. Under the system now in use, the passenger reading the how-to-open explanation cannot see the lever, and therefore it takes some time to know how to open. Exit-indicating arrows are provided on the aisle. Now, almost all the subject passengers can evacuate themselves, including senior citizens and schoolchildren. Using this emergency exit indication method generally judged to be easy to use, the time length has been shortened from the beginning of evacuation to the arrival at the emergency exit. 5 refs., 8 figs.

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

Survey and research for the enhancement of large-scale technology development 1. Japan's large-scale technology development and the effects; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 1. Nippon no daikibo gijutsu kaihatsu to sono koka

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A survey is conducted into the effects of projects implemented under the large-scale industrial technology research and development system. In the development of 'ultraperformance computers,' each of the technologies is being widely utilized, and the data service system of Nippon Telegraph and Telephone Public Corporation and the large computer (HITAC8800) owe much for their success to the fruits of the development endeavor. In the development of the 'desulfurization technology,' the fruits are in use by Tokyo Electric Power Co., Inc., and Chubu Electric Power Co., Inc., incorporated into their desulfurization systems. Although there is no practical plant based on the 'great-depth remotely controlled submarine oil drilling rig,' yet oceanic technologies and control methods are being utilized in various fields. The 'seawater desalination and by-product utilization' technologies have enabled the establishment of technologies of the top level in the world thanks to the resultant manufacture of concrete evaporator and related technologies. Eleven plants have been completed utilizing the fruits of the development. In the field of 'electric vehicle,' there is no commercialization in progress due to problems in cost effectiveness though remarkable improvement has been achieved in terms of performance. Technologies about weight reduction, semiconductor devices, battery parts and components, etc., are being utilized in many fields. (NEDO)

Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Chromosome image analysis and diagnosis device with confocal scanning laser microscope; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Kyoshoten laser kenbikyo ni yoru zensenshokutai gazo kaiseki shindan sochi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The device is now satisfactorily capable of all image processing functions (bi-levelling, color deviation, brilliance adjustment, etc.) with the exception the karyotyping function. A substance that emits fluorescence by laser excitation is developed (for labelling the probe). A direct labelling method is studied, in which nucleic acid probes (nucleic acid labelled for chromosomal identification) will prove to be remarkably high in sensitivity. A new fluorescent reagent is synthesized, which is a BHHCT-4-dUTP to act as a nucleic acid probe. It is found that the new substance is superior to the conventional fluorescent substances in terms of stability and that all chromosomes may be forced into hybridization (selective combination of a probe with a peculiar chromosome) when various probes are labelled by this substance. A programing unit is constructed for a chromosomal aberration database. Items needed relative to chromosomes and parameters relative to chromosomal aberration data are appropriately arranged, and conditions to satisfy for their development into a database are studied. A rough design of an interface is complete. (NEDO)

Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

Research report for fiscal 1998 on the analysis of spread effect of technologies approved as international standards. Value web analysis and research; 1998 nendo kokusai hyojun ni ninteisareta gijutsu no hakyu koka bunseki chosa hokokusho. Value wave bunseki chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For contributing to the formulation of technology development programs, an analysis is conducted based on the concept of value web into which the economic spread effect is incorporated. As information technology plays an important role in the fields of automobiles and chemical materials, there are various fields the research and development efforts exerted in which are common to many others. As to what additional values are created when such separately developed technologies cross each other, a discussion is conducted using techniques of industry-oriented analyses. Findings obtained are mentioned below. When the numbers of essays relative to the respective industries are compared, it is found that 63% of the total number of biotechnological essays fall on agriculture, the drug industry, and the food industry. On the other hand, when it comes to the produce, related industries larger in marketing scale is more strongly influenced by the spread effect. The spread effect of biotechnology is distinguished in the drug industry, and that of information/communication technology in the information industry, electric and electronic industries, and in the semiconductor industry. (NEDO)

FY 2000 Fundamental study for promotion of jointed implementations. Feasibility study on reducing greenhouse gas emissions by modernizing Thanlyin Refinery in Myanmar; 2000 nendo Myanmar koku Thanlyin seiyusho kindaika ni yoru onshitsu koka gas haishutsu sakugen kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The feasibility study was conducted on a project in Myanmar for the energy saving effect and reduction of the greenhouse gas emissions by introducing modern refining facilities in Thanlyin Refinery of Myanmar Petrochemical Enterprise. The project items selected as a result of the study are improvement in the heat recovery efficiency of crude distillation unit, improvement in the furnace efficiency of crude distillation unit and coker plant, improvement in the efficiency of power plant, reduction of steam loss, modernization of the cooling water system, recovery and reuse of off-gas and LPG in crude distillation unit, and modernization of intermediate products run-down system. The conceptual designs and studies on these items indicate that implementation of these projects could lead to energy saving of 25,844 tons/y as crude and CO2 emission abatement of 57,457 tons/y, 46% and 33% reduction from the baseline. The total expenses for all of these items are estimated at 4,300 million yen. These are judged to be promising projects, with estimated investment recovery period of 9 years and internal profit rate of 12.9%, when the special yen loans are available. (NEDO)

FY 1997 report on the research study on the effect of the active use of bio-technology on energy and social systems; 1997 nendo chosa hokokusho (bio-technology no katsuyo ni yoru energy shakai system ni oyobosu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For construction of a sustainable society by active use of bio-technology, a research study was made on the current state of active use of bio-technology for every industrial or social field, and the basic recognition and orientation for practice and diffusion of bio-technology. The previous typical examples of the effect of bio-technology on energy and social systems were evaluated from not only an affirmative viewpoint but also a compensatory viewpoint. Based on these examples, promising features of bio-technology and measures for active use of such features were showed for the future energy and social systems from a technological viewpoint. As a scenario for sustainable development of a society, some approaches and values about collection of rare resources, agriculture based on mass circulation, and recurrence to high-protein traditional foods such as fermented food were showed for balanced development of environment, population, and resources including energy and food. 8 refs., 14 figs., 8 tabs.

Studies on the catalysts for coal liquefaction. ; Specific behaviours of coals of different ranks in their hydrogenolysis reactions catalyzed by various kinds of catalysts. Sekitan ekikayo shokubai ni kansuru kenkyu. ; Suisoka bunkai seiseibutsu sosei ni oyobosu kakushu shokubai no koka

Energy Technology Data Exchange (ETDEWEB)

Takechi, Y; Ikenaga, N; Oda, H; Yokokawa, C [Kansai University, Osaka (Japan). Faculty of Engineering

1991-11-07

Three kinds of coals with different rank of 76, 85 and 87C% were hydrocracked to study the specific reaction behavior of four kinds of 1coal liquefaction catalysts such as CuCrO4, Fe2O3+S, MoO3-TiO2 and MoS3-Al2O3. The reaction was conducted without any solvent to find out the specific phenomenon of each combination of coal and catalyst, and terminated at the point where nearly 30% of an initial amount of coal is converted to benzene-soluble. The products were separated by GPC into four fractions, and their average molecular weights and intrinsic viscosities were measured to study characteristics of each combination. As a result, the molecular weight distribution was obviously dependent on the combination of coal and catalyst, and no specific relation was observed between the molecular weight and intrinsic viscosity. The molecular of each fraction had a bar shape with an elliptic section indicating no apparent correlation with the molecular weight. 3 refs., 1 figs., 2 tabs.

Boltzmann equation analysis of electrons swarm parameters and properties of excited particle number densities in Xe/Ne plasmas. Laser absorption effect; Xe/Ne plasma chudenshi yuso keisu narabi ni reiki ryushisu mitsudo tokusei no Boltzmann hoteishiki kaiseki. Laser ko kyushu koka

Energy Technology Data Exchange (ETDEWEB)

Uchida, S.; Sugawara, H.; Ventzek, P.; Sakai, Y. [Hokkaido University, Sapporo (Japan)

1998-06-01

Xe/Ne plasmas are important for plasma display panels and VUV light sources. However, reactions between electrons and excited particles in the mixtures are so complicated that influence of the reactions on the plasma properties is not understood well. In this work, taking account of reactions through which electrons are produced, such as cumulative and Penning ionization, and of transition between excited levels, the electron and excited particle properties in Xe/Ne plasmas are calculated using the Boltzmann equation. The ionization coefficient and electron drift velocity agreed with experimental data. The influence of laser absorption in Xe/Ne plasmas on the plasma properties is also discussed. 25 refs., 15 figs.

Development of tire road noise chassis-dynamometer simulator. Effect of ISO surface replica model pad on tire road noise; Shisakushita tire romen soon shiken`yo jissha daijo simulator ni tsuite. ISO romen mogi pad wo sochakushita koka ni kansuru kisoteki kento

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Murakami, T; Ogata, S; Sakamoto, I [Traffic Safety and Nuisance Research Inst., Tokyo (Japan)

1997-10-01

As a new test facility to clarify noise reduction method of tire road noise, Tire Road Noise Chassis-Dynamometer Simulator was developed. ISO surface replica pads made by copying the texture of ISO surface were attached on the roller surface of this system to simulate tire road noise. This paper described the specifications and characteristics of this system, and the effects of ISO surface replica pads on tire noise measurement by comparing the sound intensity in horizontal plane of tire noise measured in this system with that measured in a single drum tester with safety walk surface. 4 refs., 10 figs., 1 tab.

Report on a survey in fiscal 1999. Survey on the status of activities by European and American business enterprises related to greenhouse gas emissions trading; 1999 nendo onshitsu koka gas haishutsu ken torihiki ni kansuru Obei minkan kigyo no katsudo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Emissions trading of greenhouse gases is going to be introduced to give flexibility to the method of achieving reduction of the greenhouse gas emission established in the Kyoto Protocol. The emissions trading is an institution intended to achieve the environmental targets by using the 'market mechanism' in the environmental policies, which is expected to accomplish the effect of reducing greenhouse gas emission. The U.S.A. has adopted since 1990 the policy utilizing the emissions trading on SO2 and NOx, creating cases of successfully achieving the initial regulation targets in a short time. The history of this SO2 emissions trading showed that the emissions trading that makes the market mechanism to function can function as a policy even in the environmental policy. The representative of business enterprises working actively on this issue is BP Amco. BP Amco has started January 2000 full-fledged greenhouse gas right-to-emit institution inside the company. Among electric power companies, Ontario Power of Canada has executed about ten greenhouse gas emissions tradings yearly. Enron International has structured a system in order to participate positively in the greenhouse gas trading. (NEDO)

Corrosion control by limestone immersion into the hot water heat-storage tank. Case history of air-conditioning systems of Sapporo city subway stations; Sekkaiseki shinsekiho ni yoru chikunetsu onsui keito no boshoku koka. Sapporoshi chikatetsu kakueki no kucho setsubi no jirei

Energy Technology Data Exchange (ETDEWEB)

Kishi, M. [Sapporo City Transportation Bureau, Sapporo (Japan); Okumura, J. [Hokkaido Nikken Sekkei Ltd., Sapporo (Japan); Sakai, Y.; Shiiya, O. [Takasago Thermal Engineering Co. Ltd., Tokyo (Japan)

1995-06-05

Limestone immersion into heat-storage water tanks is a method for improving the water quality so as to encrust inner surface of piping by corrosion-preventive calcium carbonate film. For air-conditioning of Support city subway stations, heat-storing heat-pump systems with heat recovery from exhaust air have been introduced and developed for energy saving along with expansion of the subway routes. Inner surfaces of the heat-storage water tanks of all stations are coated with FRP-lining, therefore, some corrosion-preventive chemicals had been dosed from the starting up. However, the storage waters of all stations turned to red because of continuity of the piping corrosion. Instead of dosing chemicals, the limestone immersion method station. Thanks to His method, excellent results were obtained in a short period contributing control of the piping corrosion together with the red water fading. 14 figs., 1 tab.

Study on the water circulation system to improve a semi-enclosed water environment. Improvement effects of the water circulation system in a marine area; Heisasei suiiki no kyosei junkan ni yoru suishitsu kaizen. Kaiiki no jitsukoji ni okeru kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Miyaoka, S.; Tsuji, H. [Obayashi Corp., Tokyo (Japan)

1999-01-10

In recent years, oxygen-deficient water is being formed in many semi-enclosed waters, such as canals and ports, due to the load from rivers in addition to oxygen consumption in bottom sediment and poor water circulation. In general, bottom sediments have been dredged in order to improve the water environment. But there is little space to dump it. An alternative method is to artificially promote water circulation in order to move the surface water that has a high dissolved oxygen concentration to the bottom. We applied the method in a port. The system consists of air compressors, rubber tubes and unique pipes. One end of a pipe was fixed on the bottom and the other end was kept in the water by floats. Air floated up through the pipe, so the bottom water flowed up to the surface. Two months after starting to run the system, the dissolved oxygen concentration of lower water was higher than 2 mg/l, which is the criterion of water quality standard grade V, thus showing the effectiveness of the system. (author)

Report on a survey in fiscal 1999. Survey on the status of activities by European and American business enterprises related to greenhouse gas emissions trading; 1999 nendo onshitsu koka gas haishutsu ken torihiki ni kansuru Obei minkan kigyo no katsudo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Emissions trading of greenhouse gases is going to be introduced to give flexibility to the method of achieving reduction of the greenhouse gas emission established in the Kyoto Protocol. The emissions trading is an institution intended to achieve the environmental targets by using the 'market mechanism' in the environmental policies, which is expected to accomplish the effect of reducing greenhouse gas emission. The U.S.A. has adopted since 1990 the policy utilizing the emissions trading on SO2 and NOx, creating cases of successfully achieving the initial regulation targets in a short time. The history of this SO2 emissions trading showed that the emissions trading that makes the market mechanism to function can function as a policy even in the environmental policy. The representative of business enterprises working actively on this issue is BP Amco. BP Amco has started January 2000 full-fledged greenhouse gas right-to-emit institution inside the company. Among electric power companies, Ontario Power of Canada has executed about ten greenhouse gas emissions tradings yearly. Enron International has structured a system in order to participate positively in the greenhouse gas trading. (NEDO)

Report on survey of the CO2 reducing effects of regional heat supply system for urban areas in FY 1997; 1997 nendo chosa hokokusho (toshiiki wo taisho to shita koiki netsu kyokyu system no CO2 sakugen koka ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report introduces regional heat supply systems using unused energy in Japan and overseas. Evaluation examples of their CO2 reducing effects are arranged. The introduction effects were quantitatively evaluated in some urban areas in Tokyo. For the evaluation, not only the conventional energy efficiency but also energy saving and CO2 reducing effects secondarily derived from the release of a rise of temperature in urban areas were quantified, to investigate their economy. Synthetic introduction effects were estimated. As a result of the case study, the system was confirmed to be a prospective option to make CO2 reduction more than 10% in the target district. Particularly in summer, about one-fourth of the effect was brought by the restriction of heat island phenomenon. When soil heat source type district heating and cooling system was applied to the whole redevelopment area, it was found that CO2 reducing effect of the whole Tokyo is only less than 0.1%. 40 refs., 64 figs., 43 tabs.

FY1999 report of the research results of medical/engineering cooperative research project, fundamental research on diagnosis/treatment systems by imaging higher order information of living systems; 1999 nendo igaku kogaku renkeigata jigyo koji seitai joho no gazoka ni yoru shindan chiryo system ni kansuru kiban kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The research and development efforts are made for the fundamental technology necessary for visualizing higher order information of the organs and tissues at high precision and non-invasively, and for supporting treatment of the malignant tumor and cerebrovascular diseases, while keeping the functions of the affected organs intact, and the FY 1999 results are reported. The program for the visualizing techniques includes designs of the pulse sequence for a 1H/13C-MRSI analyzer which observes proton and carbon by magnetic resonance spectrometric imaging (MRSI), and starts its programming. The program for the real-time analysis of tissue dynamics starts the designs of the coil for pelvis receiving the signals for monitoring dynamics of the abdominal organs at superhigh field. The program for systems for supporting treatment while keeping the functions of the affected organs intact starts development of the MR-matching heating system, for which the applications are designed, and measures against eddy current and resistance of the system as a whole to noise are studied. Development of the high-precision supersonic wave and far-infrared ray irradiation systems is started, in order to establish the treatment aided by radiant ray while keeping functions of the affected organs intact. (NEDO)

Mercury free zinc alloy powder for alkaline manganese battery. 2. Effect of additive species to zinc particle on suppressing hydrogen gas evolution; Arukari mangan denchiyo mukoka aen gokin funmatsu. 2. Suiso gas hassei ni oyobosu aen ryushi eno tenka genso no yokusei koka

Energy Technology Data Exchange (ETDEWEB)

Yano, M.; Fujitani, S.; Nishio, K. [Sanyo electric Co. Ltd., Osaka (Japan); Akai, Y.; Kurimura, M. [Sanyo Excell Co. Ltd., Tottori (Japan)

1997-08-05

In order to make alkaline manganese batteries mercury-free and suppress hydrogen gas generation, investigations were given on the effect of additive species on modification of zinc particles present on negative electrode surface. Mercury with high hydrogen overvoltage has been added conventionally, but the mercury can cause an environmental problem. Surface modification by using indium exhibited hydrogen gas generation suppressing effect. With the surface modification amount of 0.10% by weight or more, the suppressing effect is saturated, reducing the effect to 50% of that of mercury. Surface-modifying the bismuth added zinc particles with indium showed greater suppressing effect than the case where each element is used independently. Zinc-indium (0.10% by weight) - bismuth (0.025% by weight) based alloy powder showed the same hydrogen generation suppressing effect as zinc-mercury (0.15% by weight) alloy powder. A sealed test battery using this alloy powder in negative active material exhibited a discharge capacity of 1700 mAh similarly to the initial stage even after having been stored for 20 days at 60 degC. Self-discharge characteristics equivalent to that of zinc-mercury (0.15% by weight) based alloy powder were obtained. An environment compatible dry cell battery containing no mercury whatsoever was developed successfully. 18 refs., 6 figs., 1 tab.

Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on introduction of dual mode bus system for greenhouse gas reduction; 1999 nendo onshitsu koka gas sakugen no tame no dual mode bus system donyu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A feasibility study is conducted of the above-named system in Malaysia, to be linked to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) clean development mechanism (CDM). The dual mode bus system (DMBS) is a combination of advantages of the rail running stock such as monorails and the road running stock in that the buses when running on dedicated roads are automatedly formed into a linear formation and travel at a specified economical speed. When running on ordinary roads, the formation is broken into individual buses, and they spread in the town where they travel in a planar pattern. The economical speed and reduction in air drag thanks to the linear formation saves fuel and reduces CO2 emissions. The complementary relationship to be formed with the existing public transportation systems will also function positively. Studies are conducted on condition that two routes be laid in the Kuala Lumpur urban area and one in the new city Putra Jaya. All the three routes exhibit a high economic internal rate of return, but their financial internal rate of return indicates that probabilities are low that they will pay as private businesses. They will need financial supports such as subsidies. Contribution to CO2 reduction may be slight when attention is paid only to the partial changeover from the existing bus system to DMBS but larger contribution will be found in crossover from private cars to DMBS which is higher in quality of service. (NEDO)

FY2000 report of the research results of medical/engineering cooperative research project, fundamental research on diagnosis/treatment systems by imaging higher order information of living systems; 2000 nendo igaku kogaku renkeigata kenkyu jigyo koji seitai joho no gazoka ni yoru shindan chiryo system ni kansuru kiban kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The research and development efforts are made for the fundamental technology necessary for visualizing higher order information of the physiological functions of the organs and tissues at high precision and non-invasively, and for supporting treatment of the malignant tumor and cerebrovascular diseases, while keeping the functions of the affected organs intact, and the FY 2000 results are reported. The program for the visualizing techniques includes development of the pulse sequence for commercializing the proton and carbon magnetic resonance spectrometric imaging (MRSI), and development of the prototype 1H/13C-detecting circuit. The program for the real-time analysis of tissue dynamics includes production of cine-images of, e.g., the peristalsis of the uterus, to accumulate the basic data for monitoring dynamics of the abdominal organs. The program for systems for supporting treatment while keeping the functions of the affected organs intact includes the MR-aided temperature-sensing systems, and improvement of the techniques for correcting motion of the measured organs by extracting characteristic points in the images taken and of MR-aided temperature sensing accuracy. The program for radiotherapy and ultrasonic therapy of malignant tumors in the body stems includes development of high-accuracy irradiation system aided by real-time three-dimensional body motion monitoring system. (NEDO)

FY 2000 report on the survey of the project for arrangement of the basis of the international energy utilization rationalization. Survey of diagnosis of energy conservation in main industries of ASEAN countries; 2000 nendo kokusai energy shiyo gorika kiban seibi jigyo chosa hokokusho. ASEAN shokoku shuyo sangyo ni okeru sho energy shindan chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of securing the stable energy supply/demand and contributing to the sustainable economic growth in ASEAN countries, survey of the diagnosis of energy conservation was conducted. In this survey, the diagnosis on energy conservation was made in terms of typical plants/works jointly with ASEAN-side engineers to grasp the actual state of energy consumption of each of the plants and to give advice on energy conservation policies. The countries and companies selected as objects in this fiscal year are a fiber plant in Malaysia (Arab-Malaysian Development Berhad), a paper mill in Indonesia (P.T.Kertas Leces Pulp Paper Mill) and a cement plant in Brunei (Butra Djajanti Cement SDN BHD). Diagnosis was made for each of them on January 15-19, on January 22-26 and on February 5-9, 2001, respectively. Through Workshops No. 1 (November 2000) and No. 2 (December 2000), this diagnosis program was carried out in 2001. On the basis of the results of the diagnosis, presented were the necessary energy conservation policies to be taken. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

Fiscal 1999 basic survey report for promotion of joint implementation. Feasibility study for rehabilitation and optimization of pipelines for reduction of greenhouse gas emission; 1999 nendo onshitsu koka gas haishutsu sakugen no tame no pipeline no rihabiri, saitekika no tame no F/S chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A survey is conducted of the actual state of leaks from natural gas pipelines and of the energy-saving and greenhouse gas-reducing effects of pipeline rehabilitation, with the clean development mechanism (CDM) borne in mind. Comilla and Chittagong are the areas that are covered by the survey. Natural gas leaks from the main pipelines BC and BD are calculated to be 5,300 and 5,600 tons/year, respectively. Total leakage across the country is estimated at 85,000 tons/year. Approximately 41% of the imbalance is explained by leakage while the rest is attributable to errors in gas flow measurement etc. The total leakage from branch pipelines is approximately three times larger than that from main pipelines, and some measures need to be taken to remedy the situation. For the densely populated city of Dhaka which finds itself in a network of branch pipelines, in particular, rehabilitation and optimization of its accessory power stations etc. are quite important. Measures for leakage if properly implemented will not only reduce the amount of leakage but also prevent ignition or explosion for the minimization of economic loss and for the assurance of safety. Error-free gas flow measurement if realized will strengthen the foundation on which sales are performed. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

Fiscal 1998 achievement report on regional consortium research and development project. Venture business raising type regional consortium - small business creating base type (Development of simplified diagnostic equipment for cardiovascular disorders using electrical and ultrasonic measurements); 1998 nendo choonpa oyobi denki keisokuho ni yoru kan'igata shinkekkankei kino shindan sochi no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted for the construction of a simplified system that will measure various values related to arteriosclerosis and resultant dynamic changes in blood flows, changes in cardiac muscle contraction characteristics, etc. In the development of the technology of cardiac output measurement, a measuring device using an impedance meter and an electrocardiograph is completed. An algorithm is developed for detecting irregular pulses in the electrocardiogram. In relation to cardiac muscle contraction characteristics, a sonocardiometric device is improved for the development of a device capable of measuring movements in the left ventricle walls. An algorithm is developed for the automatic recognition of the septum and the external walls in an M-mode image. In the development of a device for measuring dynamic changes in blood flows, a software program is completed, which uses a two-way rheometer to measure blood flow rates in shallow-seated arteries such as carotid arteries for the analysis of the maximum blood flow rate, acceleration, pattern, etc. In the development of an analyzer for blood vessel structures, a system capable of blood vessel structure analysis and tracking of fluctuations in walls due to cardiac cycles is developed. (NEDO)

Road drainage system using highly compressible and long-term permeable geotextile. Evaluation of long-term permeability and application to trafficability in a tunnel; Kotaiatsu mezumari taikyugata geotextile haisuizai wo mochiita roban haisui taisaku. Mezumari taikyusei no hyoka to tunnel konai kasetsu doro no trafficability kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Takahashi, S.; Yamagishi, K.; Hirama, K.; Ueno, T. [Obayashi Corp., Tokyo (Japan)

1998-07-10

A geotextile drainage material called ART-DRAIN has been developed. It was applied to temporary roads in a tunnel, to evaluate its permeability through a long-term permeability test using a model. The ART-DRAIN is a drainage material for protecting the roads from muddy conditions in a tunnel due to spring water. A filter for permeating fine soil particles was employed to keep the permeability. From the long-term permeability test using a model, appropriate permeability of ART-DRAIN was maintained for three years without blinding. There was only a slight inflow of fine grain soils into the ART-DRAIN. It was confirmed that the permeability was not obstructed by the fine grain soils. The ART-DRAIN was applied to tunnel construction works for the high-speed railway in Kyoto and the national road in mountains. From these applications, factors for enhancing the permeability effect were confirmed, which includes the selection of high quality muck, insurance of the road-bed strength by the initial compaction, use of road drainage materials with high compressible property and permeability of filter, and intervals of drainage. 1 ref., 19 figs., 1 tab.

Analysis of energy demand-supply of city and evaluation of energy conservation and peak suppression of environmental symbiosis city; Toshi no energy jukyu bunseki to shoene toshi no shoene fuka heijunka koka no hyoka (kankyo kyosei sho energy wo mezashita 60 mannin shintoshi ni tsuite no kento)

Energy Technology Data Exchange (ETDEWEB)

Iwatsubo, T.; Hashimoto, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-05-01

The paper developed an analysis method of the energy supply/demand structure of city and compared the conventional city and a city considering energy conservation. An energy supply/demand flow chart was newly proposed. From this flow chart, `energy sustainability ratios` was proposed as a new index for comprehensively evaluating two elements of the energy conservation by load reduction and heightening of energy conversion rates and the utilization of waste heat and renewable energy. A method for analysis of the energy supply/demand structure of city was developed including daily supply/demand patterns in the area where individual equipment in every residence/building correspond to the energy supply and the area where centralized energy systems such as district energy supply correspond it. From the developed analysis method, analysis was made of a newly developed city with a 0.6 million population in terms of the conventional city and energy conservation city, to clarify the present energy supply/demand structure of city and to express it in an energy flow chart. At the same time, validity of the analysis method and evaluation indexes were confirmed by comparing the conventional city and energy conservation city. 15 refs, 27 figs., 17 tabs.

Time path of marginal cost for measures against global warming toward the greenhouse gas concentration target. Analytic solution and case study of the electric power sector; Onshitsu koka gas nodo mokuhyoka deno ondanka taisaku genkai hiyo no jikan keiro. Kaisekikai to denryoku bumon no case study

Energy Technology Data Exchange (ETDEWEB)

Nagano, K.; Sugiyama, H.; Takahashi, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-01-30

The United Nations Framework Convention on Climate Change is studied from the viewpoint of implementing costs. As far as the global warming issue is concerned, the factor to affect the environment is not the emitted volume but the concentration in the air. The ultimate target is the stabilization of greenhouse gas concentration at a level not to impose serious artificial damage on the ecosystem. Accordingly, various time paths are considered, including one in which much emission is allowed at the beginning and suppression is enforced acceleratedly in the later stage. In this study, a path demanding but the minimal cost in the period up to the target time point is discussed, using as the tool the marginal cost for measure implementation. In a reasonable emission control strategy, the emission control marginal cost follows a time path that is dependent upon an increase function to be determined by the discount rate and survival rate (time constant) in the atmosphere. In the industrial branch, instead of imposing short-term and rigid emission volume control limits, a longer-term target may be set for reduction in the loads responsible for concentration acceleration, concrete emission controls under the given conditions may be implemented at the discretion of the implementing organizations, and reduction in cost may be realized by time distribution with the environmental impacts kept at approximately equal levels. 5 refs., 2 figs., 3 tabs.

Quantitative evaluation of ground improvement by chemical grouting using electrical resistivity. Part 3. Applicability of evaluation of improved region by resistivity tomography; Denki hiteiko ni yoru yakueki chunyu kairyo koka no teiryoteki hyoka hoho. 3. Hiteiko tomography wo riyoshita jiban kairyo han`i hyoka hoho no tekiyosei

Energy Technology Data Exchange (ETDEWEB)

Komine, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-02-01

This paper describes a method for evaluating grouting that is a means for improving the ground for excavation for building underground structures in urban areas. This is an effort for improving reliability, and evaluates the rate of filling of the water glass base chemical liquid injected for improving the ground utilizing the fact that this liquid is higher in conductivity than the soil or ground water. An experiment was conducted using a model ground so as to define the limit of applicability of this resistivity tomography by studying electrode arrangements and difference in resistivity between the grouted liquid and ground water. It was then found that the liquid-injected region is evaluated more accurately when the measuring electrodes are installed nearer to the region, that evaluation is satisfactorily accomplished when the region spans not less than 75% of the distance between the electrodes, that higher accuracy is expected when the difference in resistivity is greater between the grouted liquid and ground water, that evaluation is satisfactorily accomplished when the resistivity of the grouted liquid is not more than 10% of that of ground water, and that any grouting liquid usable for ground improvement in civil engineering in urban areas can be applied to any other grounds except where there is influence of seawater. 31 refs., 55 figs., 8 tabs.

FY 1998 survey report. Survey on reduction in environmental effect of greenhouse effect gas by the transfer of environmental technology in the Asian region; 1998 nendo chosa hokokusho. Asia chiiki ni okeru kankyo gijutsu iten ni yoru onshitsu koka gas no kankyo eikyo keigen ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Effects of the transfer of environmental technology were studied as an important policy for control of greenhouse effect gas in the Asian region. As schemes, those that were drew up by NEDO, JICA, etc. now exist and are used also in Japan. However, for the control of greenhouse effect gas emission which is expected to rapidly increase in future, it is indispensable to construct a new powerful and effective scheme in which technology transfer and fund to be given are organically connected. Especially, in the U.S., etc., the assistance of developing countries of a huge amount of money such as Japan's ODA is not extended. However, they position the environmental technology as an important strategy and is developing the assistance of developing countries by technology transfer and eco-business of private companies. Also in the eco-business field, the environment-related technology of Japanese companies is used in Asian developing countries, with expectations of its being a new business with international competitive strength. This is the subject for the whole global environment, and an important subject also for Japan which requires the creation of a new business field with international competitive strength. (NEDO)

Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

Fiscal 1999 basic study for promotion of joint implementation. Study of greenhouse gas reduction by modifying the power generation system of a power station in the Republic of Kazakhstan; 1999 nendo Kazakhstan ni okeru hatsudensho no hatsuden system kaishu ni yoru onshitsu koka gas sakugen ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A feasibility study is conducted aiming to reduce greenhouse gas emissions by refurbishing obsolete power stations in Shymkent City, the Republic of Kazakhstan. The clean development mechanism is also discussed. Aircraft engine-derived 20MW-class gas turbine cogenerators will be introduced, one each into a 1st and 2nd power stations. A simple-cycle model of the same will also be introduced into the 1st power station. The facility costs will be US$61.279 million for the 1st power station and US$33.590 million for the 2nd power station. The amount of fuel to be saved will be 238.6-thousand tons/year in terms of oil, totalling 5,964-thousand tons in a 25-year period. As for the reduction of greenhouse gas emissions, there will be a 737.9-thousand tons/year reduction in terms of CO2, meaning a total reduction of 18.448-thousand ton in a 25-year period. An FIRRROI (Financial Internal Rate of Return on Investment) is tentatively calculated using power and heat prices presented by the other party. The result of calculation shows that the net cash flow before and after tax stays negative throughout the whole operating period, which means a total lack of cost effectiveness. This is attributed to the low power and heat unit prices set by the other party, extremely lower than the internationally accepted prices. The FIRRROI after tax will turn positive when the unit prices are 1.5 times higher and the total investment is reduced by 20%. (NEDO)

Elucidation of hydrogen mobility in tetralin under coal liquefaction conditions using a tritium tracer method. Effects of the addition of H2S and H2O; Tritium tracer ho wo mochiita sekitan ekika hanno jokenka deno tetralin no suiso idosei hyoka. Ryuka suiso oyobi mizu no tenka koka

Energy Technology Data Exchange (ETDEWEB)

Kanbe, M.; Saito, M.; Ishihara, A.; Kabe, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1996-10-28

It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where radical does not give any effect. In the case of H2O addition, the conversion yield and hydrogen exchange rate decreased into a half or one-third. It was suggested that H2O inhibited the formation process of tetralyl radical. 6 refs., 4 figs.

Fiscal 2000 achievement report on the venture business assisting type regional consortium-Core industry creation type. Development of radiation detector utilizing surface reforming effect of irradiation; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Hoshasen shosha ni yoru hyomen kaishitsu koka wo mochiita hoshasen kenshutsuki no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

It has been clarified that the use of some kinds of semiconductor films, such as a rutile type titanium oxide film or a zirconium oxide film, results in a stable photocatalytic reaction in an intensive radioactivity region. In this effort, the effect is applied for the development of a FET (field effect transistor) type radiation detector capable of stable operation under high dose irradiation circumstances. Semiconductor materials such as a rutile type titanium oxide were subjected to irradiation tests on the ground, in which changes in their physical properties such as wettability or conductance were examined and the mechanism of surface reforming under irradiation was elucidated, and proper materials were selected. A prototype high radiation detector was fabricated that covers a 1mGy/hr-4kGy/hr region. For the establishment of a technology for growing spherical semiconductor crystals under microgravity, basic experiments were conducted using a free-fall facility at the Japan Microgravity Center. Basic experiments were conducted for the fabrication of a prototype radiation detector to operate in a high radiation region from 0.1kGy/hr to 2kGy/hr and beyond, and a prototype spherical semiconductor radiation detector was fabricated. Achievements of the effort are mentioned above. (NEDO)

FY 2000 Fundamental study for promotion of jointed implementations. Feasibility study on energy saving effect and reducing CO2 emissions by use of RDF in cement plants in China; 2000 nendo Chugoku cement kojo ni okeru RDF katsuyo ni yoru shoene koka oyobi nisanka tanso haishutsu sakugen ni kansuru feasibility study chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The feasibility study was conducted on a project in China for energy saving and greenhouse gas emission reduction by introducing the energy-saving and alternative energy technologies in cement plants. The cement plant selected for the feasibility study is Shanghai Plant of Shanghai Allied Cement Co., Ltd. (SAC), for RDF receive and supply facility, chlorine bypass facility, exhaust heat power generation facility and RDF production facility. The study results indicate that the exhaust power generation can save energy of 4,700 tons/y as crude, or energy saving rate of 25.5%, and that replacing part of coal by RDF and exhaust power generation can reduce CO2 emissions by 25,500 and 18,500 tons/y, respectively. For the investment recovery, it is estimated that the investment can be recovered in 9 years, and the project value is 81.399 million Yuan with the initial investment and project profit in each year discounted to the present value. These results fail to satisfy the SAC's investment standards. (NEDO)

Fiscal 2000 survey on electrical power supply system for the purpose of reducing greenhouse effect gas. Three scenarios for spread of distributed power generation by 2010; 2000 nendo onshitsu koka gas sakugen no tame no denryoku kyokyu system ni kansuru chosa hokokusho. 2010 nen made no bunsangata dengen fukyu ni kansuru mittsu no scenario

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An examination was conducted concerning the course of spread of distributed power generation (on-site power generation of 2,000 kW or less) by the year 2010, with three scenarios prepared. In the scenario 1, the government will completely deregulates the power market and take no other steps, leaving the matter to market competition. The universal service will be abandoned, which means higher power prices for remote regions, contributing to the spread of home power generation. In the scenario 2, the government, having reached the limits of the nuclear propulsion policy, will adopt natural gas as the center of its electrical power policy, providing preferential treatments such as subsidies and tax exemptions and requesting the power companies to increase their usage. This will lead to higher transmission charges, with distributed power generation more advantageous to the IPPs in terms of cost. In the scenario 3, environmental awareness will make increase in the capacity quite difficult including power generation facilities and transmission/distribution network, and will invite a power crisis in the long run through insufficient capacity in power generation and transmission/distribution volume. Distributed power generation requiring no reinforcement to the grid will spread such as household-use type without system interconnection, solar cells or small fuel cells. (NEDO)

Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

Effect of TiO2 addition on reaction between SiC and Ni in SiC-Ni cermet spray coatings. Part 2. ; Development of SiC-based cermet spray coatings. SiC-Ni yosha himakuchu no SiC-Ni kaimen hanno ni oyobosu TiO2 tenka no koka. 2. ; SiC-ki sametto yosha himaku no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, T [Kumano Technical College, Mie (Japan); Oki, S; Goda, S [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1992-09-30

The depression of the reaction between SiC and Ni, by adding TiO2 powder in spraying powder which has caused uniform dispersion in spray coating and reduction of TiO2 by the reaction during spraying, was studied. The mass ratio of the mixed components has been, SiC:Ni:TiO2=3:2:1. The spray coating was examined by electron prove microanalysis as well as X-ray diffractometry, centering mainly to the SiC-metal interface reaction. The formation of Ni-Si compounds have been depressed by the addition of TiO2 to spraying powder and by using plasma gas containing H2. Reason for this has been that the TiC formed in the SiC-Ni interface has depressed the reaction at the SiC-Ni interface. Further, TiO2 is reduced during spraying, and TiC is thought to be formed by the reaction between Ti and SiC or reaction between TiO2 and SiC. 8 refs., 6 figs., 1 tab.

Study of QoS control and reliable routing method for utility communication network. Application of differentiated service to the network and alternative route establishment by the IP routing protocol; Denryokuyo IP network no QoS seigyo to shinraisei kakuho no hoho. DiffServ ni yoru QoS seigyo no koka to IP ni yoru fuku root ka no kento

Energy Technology Data Exchange (ETDEWEB)

Oba, E.

2000-05-01

QoS control method which satisfies utilities communication network requirement and alternative route establishment method which is for sustaining communication during a failure are studied. Applicability of DiffServ (Differentiated Service), one of the most promising QoS control method on IP network and studying energetically in IETF WG, is studied and it is found most application used in the utility communication network except for relaying system information could he accommodated to the DiffServ network. An example of the napping of the utility communication applications to the DiffServ PHB (Per Hop Behavior) is shown in this paper. Regarding to the alternative route, usual IP routing protocol cannot establish alternative route which doesn't have common links and nodes in their paths for a destination. IP address duplication with some modification of routing protocol enables such alternative route establishment. MPLS, distance vector algorithm and link state algorithm are evaluated qualitatively, and as a result, we found MPLS is promising way to establish the route. Quantitative evaluation will be future work. (author)

Power load leveling and energy saving measures for office buildings. Power load leveling and energy saving technology for the new building of the Kobe branch of the Kansai Electric Power Co., and its effect; Office biru no denryoku fuka heijunka sho energy hosaku. Kobe shiten shinshaoku ni okeru denryoku fuka heijunka sho energy gijutsu to sono koka

Energy Technology Data Exchange (ETDEWEB)

Tsuchiyama, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

1999-06-10

This paper presents power load leveling and energy saving measures for heat source, air conditioning and lighting of the new Kobe branch building. The low-temperature hot-air system adopts an ice storage system, and reduces blowing power by 12 degreesC blowing in place of normal 16 degreesC blowing, and an initial cost by duct size reduction. The continuous air conditioning system levels an initial peak load of air conditioning as compared with normal air conditioning only for working hours for buildings with large heat capacity. In addition, as power load leveling measures for the whole building, the complete heat storage system using an underground internal melting type ice storage tank is adopted. Energy saving for lighting is achieved with a dimming lighting controlling its lighting output by inverter. The following effects are expected by these new technologies: Load leveling effect of 30%, energy saving effect of 20.2% and CO{sub 2} reduction effect of 24.1%. (NEDO)

Study on fabrication methods of composite structures (1st. report); Joule effect curing of CFRP composite structures and its application to bonding and repair. Fukugo zai kozo no seikei kako ho ni kansuru kenkyu (Dai 1po); CFRP kozo no Joule koka wo riyo shita cure ho to setsugoter dot hoshu e no oyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Moriya, K. (The National Defense Academy, Kanagawa (Japan))

1990-07-05

A method for curing CFRP composite structures by using Joule effect is presented. Due to the presence of fiber to fiber contact, CFRP composites and their prepregs exhibit electrical conductivity in the direction transverse to fibers as well as in the fiber direction, and they can be considered as electrically homogeneous on a gross scale. Therefore, passing an electric current through a CFRP prepreg, it is self-heated due to the Joule effect. Feedback current control maintains the prepreg temperature at a desired level and makes the prepreg be cured by a specified cure cycle. Experimental verifiactions have been carried out to demonstrate the feasibility of the present technique. The applications to the bonding of CFRP components and to the patch repairs of effective CFRP structure are also described. 12 refs., 12 figs.

Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

Study on behavior of car and driver in the very small commuter car made of FRP during collision using scale model. Under the consideration of thorax deformation of driver using airbag; FRP sei mokei ni yoru FRP sei chokeiryo jissha shototsuji no kuruma to join no anzensei ni kansuru kenkyu. Kyobu henkei tokusei wo yusuru join ni taisuru air gab no koka

Energy Technology Data Exchange (ETDEWEB)

Sakai, H; Morisawa, M; Yoshino, T [Musashi Institute of Technology, Tokyo (Japan); Sato, T [Keio University, Tokyo (Japan); Ishizuki, H [Satake Co., Tokyo (Japan)

1997-10-01

In this study, after having performed simulation which took up scale models substituting for full scale model of commuter car made of FRP, we carried out collision tests to barrier. Here, we made enquiries about the occupant safety by changing the collision speed and the deformation characteristics of the seat belt, during head-on barrier collision using one-fifth scale models. We sought for the occupant`s safe combinations among the deformation characteristics of airbag and the thorax deformation. In this case, the degree of the occupants injury were estimated using HIC values, 3msecG and maximum deformation of the thorax. 7 refs., 5 figs.

FY 2000 report on the basic survey to promote the joint implementation. Potential survey of the greenhouse effect gas reduction by high-efficient utilization of the oil residue in Bataan Refinery in the Philippines; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Philippines koku Bataan seiyusho ni okeru sekiyu zansa kokoritsu riyo ni yoru onshitsu koka gas sakugen kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of reducing the CO2 emitted from electricity/vapor supply facilities of Bataan Refinery in the Philippines, study was conducted of optimum energy supply facilities considering the effective use of the oil residue and future reinforcement of the refinery. Concerning the high-pressure/high-temperature condensing extraction boiler/turbine cogeneration, gas turbine cogeneration and low speed diesel engine cogeneration, comparative study was carried out in terms of thermal efficiency, reliability/preservation, environmental acceptability, effectiveness of measures for the future excessive oil residue, etc. As a result, the study was concluded as follows: the electric power consumption will markedly increase in the future; however, in the light of the situation of the refinery where the vapor demand will not increase, it is the most suitable to use low speed diesel engine cogeneration facilities as on-site power generation facilities which can burn the excessively increasing oil residue as direct fuel. The CO2 reduction effect estimated from the project on the present scale was 132,880 t-CO2/y, and the energy conservation effect estimated was 50,861 toe/y. (NEDO)

Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

Report on research results of the FY 2000 medical/engineering cooperative research project. Fundamental research on microelectrode-aided gene information measurement system (Research and development of gene diagnostic system using superhigh-sensitivity microelectrode DNA chip ECA - electrochemical array); 2000 nendo igaku kogaku renkeigata kenkyu jigyo kenkyu seika hokokusho. Bisho denkyoku riyo idenshi joho keisoku system ni kansuru kiban kenkyu (chokokandogata bisho denkyoku DNA chip ECA (denki kagaku allay) wo mochiita idenshi shindan system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The fundamental research is conducted for developing the microelectrode on which a synthetic oligonucletide probe is immobilized, and for establishing the system capable of detecting the hybrid formation simply and quickly, in order to develop the advanced DNA chips for diagnosis. The project results include development of the prototype array electrode with 25 1mm-diameter gold electrodes uniformly arranged at intervals of 4.5mm; development of the electrochemical activity analyzer for multi-electrode systems, showing the performance almost on a level with that of the existing electrochemical analyzer for the single-electrode systems; establishment of the gene databases; development of the method which can produce a sufficient quantity of nucleic acid for DNA chip analysis by studying the method of preparing the nucleic acid from the blood serum, preparing RNA from a trace quantity of the living liver sample and amplifying the genes, wherein the nucleic acid is produced while its profile before the amplification is kept intact; and establishment of the method for detecting the hepatitis B virus by combining the electrochemical detection of DNA by a non-immobilized probe with the PCR method. (NEDO)

Fundamental cooperation project in fiscal 2000 for improving international energy consumption efficiency. Investigations in relation with prevention of global warming (analytical comparison centering around cost effectiveness related to greenhouse effect gas (GHG) reduction in overseas countries); 2000 nendo kokusai energy shohi koritsu ka chosa nado kyoryoku kiso jigyo - chikyu ondanka boshi kanren chosa hokokusho. Kaigai deno GHG sakugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to provide discussion materials for measures to achieve the GHG emission reduction target, investigations and discussions have been made on the following subjects: cost effectiveness of reducing GHG emission by target countries and target technologies, use of maps and databases on the possible reduction quantity of GHG emission, the targeted countries and business categories. Regarding the target countries, investigations were made on the general situation of the energy consumption efficiency, difference between their energy consumption efficiency by industries and that in Japan, and the GHG emission quantities by sectors. As a result, 31 counties hopeful in reducing CO2 emission were selected. With regard to technologies to reduce CO2 emission, technologies having been practically used and proliferated in Japan were used as the base, whereas 43 technologies were systematized for such departments as industries, business operations, households, and transportation. According to a trial calculation on the effect of CO2 emission reduction, if the 43 technologies are applied to the 31 target countries, CO2 emission reduction of 698 million tons as a whole would be possible, for which the required expense was calculated as 114.4 trillion yen. In evaluating the CO2 emission reducing technologies, the cost effectiveness of each technology was evaluated by cost per GHG emission reduction of 1t-CO2. (NEDO)

FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of ocean-based artificial deep ocean water (DOW) upwelling devices and researches into enhancement of productivity of surface waters, CO2 fixation and biological effects of DOW; 1998 nendo yojo kaiyo shinsosui shusui system no kaihatsu to kaiyo hiyokuka, nisanka tanso kyushu oyobi seibutsu koka no kenkyu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D project is implemented for design, fabrication and installation of ocean-based artificial deep ocean water (DOW) upwelling devices which can take DOW at low cost in an ocean; experiments for enhancing productivity of ocean by adding DOW using mesocosms; and studying the biological effects of DOW for keeping freshness of marine products. DOW is successfully taken by the upwelling system from a depth of 800 m in a sea area 2,000 m or more in depth. The system has worked to perform its functions even when attacked by typhoons, which caused wave height of 10 m or more. For enhancing productivity of ocean, the culture experiments are conducted in a small-size, on-shore tank, and the mesocosm experiments in a harbor. The results indicate that addition of DOW increases the phytoplankton phase and its quantity. It is also observed that addition of iron ion further accelerates the fertilizing effect. The results of the experiments conducted in a harbor also indicate that DOW has the fertilizing effect, even in a very small quantity, increasing quantity of small zooplankton. No definite effect of DOW, liquid or ice, is observed for keeping freshness of sliced raw sea bream and bonito. (NEDO)

Report on investigations in fiscal 2000 on the global warming prevention related investigations in cooperative fundamental project of investigating improvement in international energy consumption efficiency. Analysis and comparison centering on cost effectiveness in relation with greenhouse gas (GHG) reduction in Japan; 2000 nendo kokusai energy shohi koritsuka chosanado kyoryoku kiso jigyo chikyu ondanka boshi kanren chosa hokokusho. Kokunai deno GHG sakyugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The present investigative research is intended to grasp the whole image of cost effectiveness of the energy saving and new energy technologies to suppress and reduce CO2 emission in Japan. Furthermore, the research considers the cost effectiveness and discusses the efficiency and the directionality of reducing CO2 emission from an estimation of the social introduction cost of individual technologies and quantity of CO2 emission reduction. These activities are intended to provide the fundamental items of information when discussing the measures to achieve the emission reduction target imposed on Japan. The research divides the whole aspect into energy conversion, industrial, consumer and transportation departments for discussion, and calculates the technological items that can be introduced by 2010 and the quantity of the introduction thereof, as well as the effect of reducing CO2 emission. Calculations are also performed on 27 elementary technologies in total and the CO2 emission reducing effect, assuming technological possibilities. Subsequently, analyses are carried out from the viewpoint of cost effectiveness by departments. It is shown that the average cost effectiveness is distributed in the range from 108,000 yen/ton to 1,129,000 yen/ton. Scenarios of reducing CO2 emission are discussed from the analyses of the cost effectiveness. (NEDO)

FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

FY 2000 report on the research cooperation project 'research cooperation diagnosis survey.' Research cooperation in technology to improve the environmental response type industrial use water circulation utilization (Thailand) Nos. 1 and 2. and research cooperation in technology to recover the harmless metal in smoke/ash in smelting works (Chile); 2000 nendo kenkyu kyoryoku jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Kankyo taiogata kogyoyosui junkan riyo kojo gijutsu ni kansuru kenkyu kyoryoku (Tai) 1 kaime 2 kaime, seirenjo enbai no mugaika kinzoku kaishu gijutsu ni kansuru kenkyu kyoryoku (Chiri)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In Chile, for the purpose of coping with problems on the ground subsidence and water shortage caused by pumping up the industrial use ground water, survey was conducted of the research cooperation in reutilization of the industrial waste water retreated for the food industry and the fiber industry. As a result, as a MOU plan, the establishment of the regenerative utilization technology was proposed of the treated water after the activated sludge treatment in food plants and after the Lagoon treatment in the fiber/dyeing industry. In Chile, relating to the harmless metal recovery technology to recover valuable metals such as copper, lead, zinc and silver included in the smoke/ash containing arsenic in copper smelting works at low cost by reducing environmental loads, conducted were survey for research cooperation and discussion on the making of a draft of the basic agreement. The project includes the high grade leaching separation, simplification/non-slagging of the lead/silver residue melting process, optimization of the copper separation/recovery method, fixation/weight-reduction of the leached arsenic, optimization of the zinc recovery method, optimization of the final waste water treating process, study of the design/construction/operation of the pilot plant, etc. (NEDO)

Report on diagnosis and survey on research cooperation in the research cooperation promotion project in fiscal 1994. Research cooperation on manufacturing clean fuel for consumer use from gasified coal gas / Research cooperation on a method for pulp manufacturing of low-pollution and energy saving type by using non-wood raw materials; 1994 nendo kenkyu kyoryoku suishin jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Sekitan gas ka gas kara no minseiyo clean nenryo seizo ni kansuru kenkyu kyoryoku / himokuzaikei genryo wo mochiita teikogai shoenegata pulp seizoho ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In solving the problems in developing technologies peculiar to developing countries, Japan will provide cooperation. This paper describes the achievements in diagnosis and survey in fiscal 1994. Development will be made on a manufacturing process for dimethylether (DME), a synthesizable and portable clean fuel, by using coal produced in China. Annual DME production of 10,000 tons will make it possible to supply 50,000 households with the fuel of one year consumption, whereas return on the construction investment and profit can be expected. At the Shanxi Coal Chemistry Research Institute, a 500 tons a year plant making DME from gasified coal gas is scheduled to begin operation. Development will be made on a pulp manufacturing technology in China, in which environmental pollution due to waste water is largely reduced, and operation cost is reduced. Application of the oxygen-alkaline evaporation and decomposition process developed in Japan will be considered, which uses non-wood raw material such as rice straw, wheat straw and megass). The raw materials are immersed continually in low-concentration alkaline solution, dehydrated, and then lignin is oxidized and decomposed by using oxygen in a continuous oxidation reactor to make the material into pulp. China uses non-wood materials as paper raw materials at 80%, whereas effects are expected in waste water pollution prevention, energy saving, resource saving and economics. (NEDO)

FY 2000 report on the research cooperation project 'research cooperation diagnosis survey.' Research cooperation in technology to improve the environmental response type industrial use water circulation utilization (Thailand) Nos. 1 and 2. and research cooperation in technology to recover the harmless metal in smoke/ash in smelting works (Chile); 2000 nendo kenkyu kyoryoku jigyo 'kenkyu kyoryoku shindan chosa' hokokusho. Kankyo taiogata kogyoyosui junkan riyo kojo gijutsu ni kansuru kenkyu kyoryoku (Tai) 1 kaime 2 kaime, seirenjo enbai no mugaika kinzoku kaishu gijutsu ni kansuru kenkyu kyoryoku (Chiri)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In Chile, for the purpose of coping with problems on the ground subsidence and water shortage caused by pumping up the industrial use ground water, survey was conducted of the research cooperation in reutilization of the industrial waste water retreated for the food industry and the fiber industry. As a result, as a MOU plan, the establishment of the regenerative utilization technology was proposed of the treated water after the activated sludge treatment in food plants and after the Lagoon treatment in the fiber/dyeing industry. In Chile, relating to the harmless metal recovery technology to recover valuable metals such as copper, lead, zinc and silver included in the smoke/ash containing arsenic in copper smelting works at low cost by reducing environmental loads, conducted were survey for research cooperation and discussion on the making of a draft of the basic agreement. The project includes the high grade leaching separation, simplification/non-slagging of the lead/silver residue melting process, optimization of the copper separation/recovery method, fixation/weight-reduction of the leached arsenic, optimization of the zinc recovery method, optimization of the final waste water treating process, study of the design/construction/operation of the pilot plant, etc. (NEDO)