WorldWideScience

Sample records for dme pilot quantity

  1. Effects of DME pilot quantity on the performance of a DME PCCI-DI engine

    International Nuclear Information System (INIS)

    Wang Ying; He Li; Zhou Longbao; Li Wei

    2010-01-01

    The combination of premixed charge compression ignition and conventional direct-injection compression ignition combustion is studied in a DME engine. This combustion mode is referred to as PCCI-DI combustion. The pilot quantity is found to be one of main variables affecting the PCCI-DI combustion. So, the main objectives of this paper are to examine the effect of different DME pilot quantities on combustion and emission characteristics in a single-cylinder direct-injection DME engine and to determine whether PCCI-DI is a viable in-cylinder NO x emissions reduction technology. In order to evaluate the characteristics of PCCI-DI combustion, the conventional direct-injection compression-ignition engine performance is supplied to make a comparison with their results. Furthermore, special emphasis is put upon the combined combustion process analysis. Results show that DME engine can operate at a wide range of speeds and loads at PCCI-DI mode. In comparison to the conventional DME CI combustion, the brake thermal efficiency slightly increases for DME PCCI-DI operation. PCCI-DI is capable to decrease NO x effectively for all loads. NO x emission shows an obviously descending tendency with an increase in DME pilot quantity at low loads, while it shows a mildly elevating tendency with an increase in DME pilot quantity at high loads. HC and CO emissions increase for DME PCCI-DI operation under various DME pilot quantities.

  2. Effect of Pilot Injection Timings on the Combustion Temperature Distribution in a Single-Cylinder CI Engine Fueled with DME and ULSD

    Directory of Open Access Journals (Sweden)

    Jeon Joonho

    2016-01-01

    Full Text Available Many studies of DiMethyl Ether (DME as an alternative fuel in Compression-Ignition (CI engines have been performed. Although diverse DME engine research has been conducted, the investigation of combustion behavior and temperature distribution in the combustion engine has not progressed due to the fact that there is no sooting flame in DME combustion. In order to investigate the combustion characteristics in this study, the KIVA-3 V code was implemented to research various pilot injection strategies on a single-cylinder CI engines with DME and Ultra-Low-Sulfur Diesel (ULSD fuels. The combustion distribution results obtained from the numerical investigation were validated when compared with the measurement of flame temperature behaviors in the experimental approach. This study showed that long intervals between two injection timings enhanced pilot combustion by increasing the ambient pressure and temperature before the start of the main combustion. Different atomization properties between DME and ULSD fuels contributed to the formation of a fuel-air mixture at the nozzle tip and piston lip regions, separately, which strongly affected the temperature distribution of the two fuels. In addition, the pilot injection timing played a vital role in regard to ignition delay and peak combustion temperatures. Exhaust emissions, such as NOx and soot, are related to the local equivalence ratio and temperature in the combustion chamber, also illustrated by the contrary result on a Φ (equivalence ratio – T (temperature map.

  3. Dimethyl Ether (DME); Le Dimethyl Ether (DME)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    Total is an active participant in research to develop new gas-to-liquids (GTL) processes to obtain automotive fuel, olefins and other liquids from natural gas. Among the various processes for chemical conversion of natural gas, direct synthesis of DME destroys the least amount of gas, making it highly efficient. The thermal efficiency of the process developed by Japan JFE is 65 to 70%, higher than the conventional Fischer Tropsch process. This document presents the researches and the program of Total on this process. (author)

  4. A pilot study to evaluate runoff quantity from green roofs.

    Science.gov (United States)

    Lee, Ju Young; Lee, Min Jung; Han, Mooyoung

    2015-04-01

    The use of green roofs is gaining increased recognition in many countries as a solution that can be used to improve environmental quality and reduce runoff quantity. To achieve these goals, pilot-scale green roof assemblies have been constructed and operated in an urban setting. From a stormwater management perspective, green roofs are 42.8-60.8% effective in reducing runoff for 200 mm soil depth and 13.8-34.4% effective in reducing runoff for 150 mm soil depth. By using Spearman rank correlation analysis, high rainfall intensity was shown to have a negative relationship with delayed occurrence time, demonstrating that the soil media in green roofs do not efficiently retain rainwater. Increasing the number of antecedent dry days can help to improve water retention capacity and delay occurrence time. From the viewpoint of runoff water quality, green roofs are regarded as the best management practice by filtration and adsorption through growth media (soil). Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Dimethyl Ether (DME)

    International Nuclear Information System (INIS)

    2006-01-01

    Total is an active participant in research to develop new gas-to-liquids (GTL) processes to obtain automotive fuel, olefins and other liquids from natural gas. Among the various processes for chemical conversion of natural gas, direct synthesis of DME destroys the least amount of gas, making it highly efficient. The thermal efficiency of the process developed by Japan JFE is 65 to 70%, higher than the conventional Fischer Tropsch process. This document presents the researches and the program of Total on this process. (author)

  6. Combustion and emission characteristics of a diesel engine with DME as port premixing fuel under different injection timing

    International Nuclear Information System (INIS)

    Wang, Ying; Zhao, Yuwei; Xiao, Fan; Li, Dongchang

    2014-01-01

    Highlights: • Combustion and emission of diesel engine with DME as premixing fuel were examined. • Injection timing has profound effect on HRR of diffusive combustion in PCCI engine. • DME introduction drastically influenced HRR of PCCI combustion, especially for HTR. • Effect of injection timing on emission of PCCI engine is similar to that of DICI engine. - Abstract: This work dealt with the combustion and exhaust performance of a DME premixed charge compression ignition diesel engine. With the port premixing DME, the heat-release process was made up of the premixed charge homogeneous charge compression ignition combustion and diffusion combustion. The in-cylinder fuel injection timing and port premixing DME quantity played the important roles in combustion and emission control. They had little impact on the peak position of heat-release rate (HRR) during LTR phase. However, they had great effects on the peak values and the crank-angle positions corresponding to the HRR peaks during HTR and diffusion combustion phase. The peak value of HRR increased and the crank-angle corresponding to the HRR peak advanced with an incremental DME quantity or an early injection during HTR phase. However, the peak value of HRR dropped with an incremental DME quantity or a late injection during the diffusion combustion phase. p max and T max increased with an incremental DME quantity or an early injection. At the fixed direct-injection timing, BSFC decreased slightly with a rise of DME quantity due to CA50 closer to TDC. At a fixed DME quantity, BSFC was lowest when diesel was injected into cylinder at 7°CA BTDC. Moreover, as more DME was aspirated from port, NO x emissions decreased firstly but this decreasing trend ceased later. Smoke reduced, but CO and HC increased with a rise of DME quantity. Meanwhile, like the conventional DICI operation, NO x increased, but smoke, CO and HC declined with an early direct-injection

  7. Effect of pilot fuel quantity on the performance of a dual fuel engine

    Energy Technology Data Exchange (ETDEWEB)

    Abd Alla, G.H.; Soliman, H.A.; Badr, O.A.; Abd Rabbo, M.F. [Zagazig University, Cairo (Egypt). Shoubra Faculty of Engineering

    2000-04-01

    It is well known that the operation of dual fuel engines at lower loads suffers from lower thermal efficiency and higher unburned percentages of fuel. To rectify this problem, tests have been conducted on a special single cylinder compression ignition research engine (Ricardo E6) to investigate the effect of pilot fuel quantity on the performance of an indirect injection diesel engine fuelled with gaseous fuel. Diesel fuel was used as the pilot fuel and methane or propane was used as the main fuel which was inducted into the intake manifold to mix with the intake air. Through experimental investigations, it is shown that, the low efficiency and excess emissions at light loads can be improved significantly by increasing the amount of pilot fuel, while increasing the amount of pilot fuel at high loads led to early knocking. (author)

  8. Quantity Distortion Effect in Consumers' Perception of Different Volumes and Weights of Money: A Pilot Study.

    Science.gov (United States)

    Guido, Gianluigi; Piper, Luigi; Prete, M Irene; Mileti, Antonio; Fonda, Marco

    2016-08-01

    Consumers tend to misunderstand the physical value of cash money by adopting improper anchors for their judgments (e.g., banknote size and shape, currency denominations, etc.). In a pilot study carried out on a sample of 242 participants (n = 116 men; M age = 29.6 year, SD = 10.8), a quantity distortion effect was demonstrated by evaluating consumers' misperceptions of different monetary quantities, either in terms of volume or weight, using banknotes of the same denomination (€50). A threshold value was found, for both volume (€876,324) and weight (€371,779), above (below) which consumers tend to overrate (underrate) monetary amounts. The theoretical and operative implications are discussed. © The Author(s) 2016.

  9. The Lubrication Qualities of Dimethyl Ether (DME)

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Sorenson, Spencer C; Jakobsen, J.

    2002-01-01

    by mixing the DME with reasonable amounts of additives. The main conclusion drawn from these measurements is that a combination of lubricity and viscosity comparable to one of diesel oil cannot be reached in the case of DME unless a huge amount of additive is used. This is not an attractive solution...

  10. Production of methanol/DME from biomass

    DEFF Research Database (Denmark)

    Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Münster-Swendsen, Janus

    In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier...... cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51...... gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic...

  11. How to Initiate and Develop the Market of DME - With Focus on Bio-DME?

    Energy Technology Data Exchange (ETDEWEB)

    Baudin, Anders; Nordvall, Hans-Olof (School of Engineering, Linnaeus Univ., Vaexjoe (Sweden))

    2010-01-15

    The theme of this study is how to initiate and develop the market for DME with focus on Bio-DME. In particular, the view considered is that DME can replace diesel and LPG. Initiating and market development for other application is not included here. Regional diesel prices are highly correlated. One can even argue that there seems to be a world market price. Furthermore, they are strongly volatile, which can be traced to the relationship to crude oil. The volatility in diesel - and oil - prices is taken care of in a well developed market for financial instruments (e.g. futures, options). Similar financial risk handling is not yet available for the unit price of DME. A considerable amount of structured information exists in companies, also with consultants and researchers, on how different end-use sectors are expected to react to variation in diesel prices. Knowledge of the end-use sectors' likely reaction to the introduction of DME prices in comparison to diesel prices is generally unknown and is thus only subject to discussion. Obtaining information on this process is, however, the crucial point in the introduction of the market for (bio-)DME. In the short term the introduction phase might be shorter if DME could be mixed with diesel (cf. DME in LPG). This would imply unaltered infrastructure. The advantage of leaving aside adaptation of engines and changing infrastructure would imply that the thresholds for introduction of DME are reduced - the consequence would be that larger production volumes of DME would be obtained quicker. The business risk would also be reduced. But is it possible to mix DME (fossil and bio) with diesel? One standpoint is that this is impossible. Other researchers argue that mix is possible up to 25 per cent - some claim even higher. The problem is that viscosity tends to be too low. Further studies will cast light on this problem. Parallel efforts should be initiated to introduce systems with 100 per cent DME. This requires adaptation

  12. Production of methanol/DME from biomass

    Energy Technology Data Exchange (ETDEWEB)

    Ahrenfeldt, J.; Birk Henriksen, U.; Muenster-Swendsen, J.; Fink, A.; Roengaard Clausen, L.; Munkholt Christensen, J.; Qin, K.; Lin, W.; Arendt Jensen, P.; Degn Jensen, A.

    2011-07-01

    In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier types have been investigated in this project: 1) The Two-Stage Gasifier (Viking Gasifier), designed to produce a very clean gas to be used in a gas engine, has been connected to a lab-scale methanol plant, to prove that the gas from the gasifier could be used for methanol production with a minimum of gas cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51-58% (LHV). By using waste heat from the plants for district heating, the total energy efficiencies could reach 87-88% (LHV). 2) A lab-scale electrically heated entrained flow gasifier has been used to gasify wood and straw. Entrained flow gasifiers are today the preferred gasifier type for commercial coal gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic fraction of the biomass that is not converted to gas appears as soot. Thermodynamic computer models of DME and methanol plants based on using entrained flow gasification were created to show the potential of such plants. These models showed that the potential torrefied biomass to DME/methanol + net electricity energy efficiency was 65-71% (LHV). Different routes to produce liquid transport fuels from biomass are possible. They include production of RME (rapeseed oil

  13. Dual-fuel HCCI operation with DME/LPG/gasoline/hydrogen

    International Nuclear Information System (INIS)

    Bae, C.

    2009-01-01

    The advantages of homogeneous charge compression ignition (HCCI) engines include usage of the different type of fuels, ultra low nitrogen oxide and particulate matter emissions and improved fuel economy. Disadvantages include an excessive combustion rate, engine noise, and hydrocarbon and carbon emissions. An experiment on dual-fuel HCCI operation with dimethyl ether (DME)/liquefied petroleum gas (LPG)/gasoline/hydrogen was presented. The advantages and disadvantages were first presented and the dual-fuel HCCI combustion engine was illustrated through an experimental apparatus. The experimental conditions were also presented in terms of engine speed, DME injection quantity, LPC injection quantity, and LPC composition. Experimental results were discussed for output performance and indicated mean effective pressure (IMEP). It was concluded that the effect of LPG composition in a DME-LPG dual-fueled HCCI engine at various injection quantity and injective timing were observed. Specifically, it was found that propane was a more effective way to increase IMEP in this study, and that in a DME HCCI engine, higher load limit was extended by using LPG as an ignition inhibitor. tabs., figs.

  14. Basic Stand Alone Medicare DME Line Items PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Durable Medical Equipment (DME) Line Items Public Use Files (PUF) with information from Medicare DME claims. The...

  15. Ignition of DME and DME/CH4 at High Pressure: Flow Reactor Experiments and Kinetic Modeling

    DEFF Research Database (Denmark)

    Hashemi, Hamid; Christensen, Jakob Munkholt; Glarborg, Peter

    The pyrolysis and oxidation of dimethyl ether (DME) and its mixtures with methane were investigated at high pressures (50 and 100 bar) and intermediate temperatures (450―900 K) in a laminar flow reactor. DME pyrolysis started at 825 K (at 50 bar). The onset of DME reaction was detected at 525―550 K...

  16. Optimal design of intensified processes for DME synthesis

    NARCIS (Netherlands)

    Bîldea, Costin Sorin; Győrgy, Romuald; Brunchi, Cristian C.; Kiss, Anton A.

    2017-01-01

    Dimethyl ether (DME) is widely used as green aerosol propellant, precursor to other organic compounds, or as a clean fuel for diesel engines or in combustion cells. The classic method for producing DME is by dehydration of methanol in a catalytic gas-phase reactor, and purification in a direct

  17. Quality and Quantity of Rehabilitation Exercises Delivered By A 3-D Motion Controlled Camera: A Pilot Study.

    Science.gov (United States)

    Komatireddy, Ravi; Chokshi, Anang; Basnett, Jeanna; Casale, Michael; Goble, Daniel; Shubert, Tiffany

    2014-08-01

    Tele-rehabiliation technologies that track human motion could enable physical therapy in the home. To be effective, these systems need to collect critical metrics without PT supervision both in real time and in a store and forward capacity. The first step of this process is to determine if PTs (PTs) are able to accurately assess the quality and quantity of an exercise repetition captured by a tele-rehabilitation platform. The purpose of this pilot project was to determine the level of agreement of quality and quantity of an exercise delivered and assessed by the Virtual Exercise Rehabilitation Assistant (VERA), and seven PTs. Ten healthy subjects were instructed by a PT in how to perform four lower extremity exercises. Subjects then performed each exercises delivered by VERA which counted repetitions and quality. Seven PTs independently reviewed video of each subject's session and assessed repetitions quality. The percent difference in total repetitions and analysis of the distribution of rating repetition quality was assessed between the VERA and PTs. The VERA counted 426 repetitions across 10 subjects performing the four different exercises while the mean repetition count from the PT panel was 426.7 (SD = 0.8). The VERA underestimated the total repetitions performed by 0.16% (SD = 0.03%, 95% CI 0.12 - 0. 22). Chi square analysis across raters was χ 2 = 63.17 (df = 6, p<.001), suggesting significant variance in at least one rater. The VERA count of repetitions was accurate in comparison to a seven member panel of PTs. For exercise quality the VERA was able to rate 426 exercise repetitions across 10 patients and four different exercises in a manner consistent with five out of seven experienced PTs.

  18. Oral minocycline for the treatment of diabetic macular edema (DME): results of a phase I/II clinical study.

    Science.gov (United States)

    Cukras, Catherine A; Petrou, Philip; Chew, Emily Y; Meyerle, Catherine B; Wong, Wai T

    2012-06-22

    Inflammation contributes significantly to the pathogenesis of diabetic macular edema (DME). In particular, retinal microglia demonstrate increased activation and aggregation in areas of DME. Study authors investigated the safety and potential efficacy of oral minocycline, a drug capable of inhibiting microglial activation, in the treatment of DME. A single-center, prospective, open-label phase I/II clinical trial enrolled five participants with fovea-involving DME who received oral minocycline 100 mg twice daily for 6 months. Main outcome measurements included best-corrected visual acuity (BCVA), central retinal subfield thickness (CST), and central macular volume using spectral domain optical coherence tomography (SD-OCT) and late leakage on fluorescein angiography (FA). Findings indicated that the study drug was well tolerated and not associated with significant safety issues. In study eyes, mean BCVA improved continuously from baseline at 1, 2, 4, and 6 months by +1.0, +4.0, +4.0, and +5.8 letters, respectively, while mean retinal thickness (CST) on OCT decreased by -2.9%, -5.7%, -13.9, and -8.1% for the same time points. At month 6, mean area of late leakage on FA decreased by -34.4% in study eyes. Mean changes in contralateral fellow eyes also demonstrated similar trends. Improvements in outcome measures were not correlated with concurrent changes in systemic factors. In this pilot proof-of-concept study of DME, minocycline as primary treatment was associated with improved visual function, central macular edema, and vascular leakage, comparing favorably with historical controls from previous studies. Microglial inhibition with oral minocycline may be a promising therapeutic strategy targeting the inflammatory etiology of DME. (ClinicalTrials.gov number, NCT01120899.).

  19. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Andre L. Boehman; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The laboratory studies have included work with a Navistar V-8 turbodiesel engine, demonstration of engine operation on DME-diesel blends and instrumentation for evaluating fuel properties. The field studies have involved performance, efficiency and emissions measurements with the Champion Motorcoach ''Defender'' shuttle bus which will be converted to DME-fueling. The results include baseline emissions, performance and combustion measurements on the Navistar engine for operation on a federal low sulfur diesel fuel (300 ppm S). Most recently, they have completed engine combustion studies on DME-diesel blends up to 30 wt% DME addition.

  20. Theoretical study of the effects of pilot fuel quantity and its injection timing on the performance and emissions of a dual fuel diesel engine

    International Nuclear Information System (INIS)

    Papagiannakis, R.G.; Hountalas, D.T.; Rakopoulos, C.D.

    2007-01-01

    Various solutions have been proposed for improving the combustion process of conventional diesel engines and reducing the exhaust emissions without making serious modifications on the engine, one of which is the use of natural gas as a supplement for the conventional diesel fuel, the so called dual fuel natural gas diesel engines. The most common type of these is referred to as the pilot ignited natural gas diesel engine (PINGDE). Here, the primary fuel is natural gas that controls the engine power output, while the pilot diesel fuel injected near the end of the compression stroke auto-ignites and creates ignition sources for the surrounding gaseous fuel mixture to be burned. Previous research studies have shown that the main disadvantage of this dual fuel combustion is its negative impact on engine efficiency compared to the normal diesel operation, while carbon monoxide emissions are also increased. The pilot diesel fuel quantity and injection advance influence significantly the combustion mechanism. Then, in order to examine the effect of these two parameters on the performance and emissions, a comprehensive two-zone phenomenological model is employed and applied on a high-speed, pilot ignited, natural gas diesel engine located at the authors' laboratory. According to the results, the simultaneously increase of the pilot fuel quantity accompanied with an increase of its injection timing results to an improvement of the engine efficiency (increase) and of the emitted CO emissions (decrease) while it has a negative effect (increase) of NO emissions

  1. The Mark III vertex chamber: Studies using DME

    International Nuclear Information System (INIS)

    Pitman, D.

    1987-04-01

    Studies have been performed using a prototype of a pressurized wire vertex chamber with 8 mm diameter straw geometry. A 35 μm spatial resolution using dimethyl ether (DME) at 1 bar and 30 μm using argon ethane (50/50 mixture) at 4 bar was obtained. Preliminary studies show the DME to adversely affect such materials as aluminized Mylar and Delrin

  2. Magnetic fields and dense chromospheres in dMe stars

    International Nuclear Information System (INIS)

    Mullan, D.J.

    1975-01-01

    We examine in a semi-quantitative fashion the hypothesis that dense chromospheres of dMe stars are heated by dissipation of hydromagnetic waves. We propose that dMe stars are a set of magnetic stars on the lower main sequence, with strong fields presumably generated by dynamo action in deep convective envelopes. We discuss how the combination of magnetic fields and dense chromospheres in dMe stars provides a consistent interpretation of the following features: 1) The dMe stars which are most likely to be flares stars are those with hydrogen lines in emission. However, it is proposed that in certain conditions, Balmer lines may appear in absorption, and we suggest that 'negative flares' can be explained at least in part by the occurrence of strong absorption in Hα. 2) The propagation of flare-initiated coronal waves can trigger sympathetic stellar flares. 3) Apart from flare activity, emission line strengths in dMe stars must exhibit time variations due to the emergence of new magnetic flux ropes through the stellar surface. 4) The combination of strong magnetic fields with dense chromospheres makes the Faraday rotation measure large enough to have potentially a detectable effect on polarized visible light. 5) It is suggested that grain formation occurs in starspots on dMe stars. (orig./WL) [de

  3. '3Dme--a look inside' creative studio.

    Science.gov (United States)

    Brannelly, Sonya

    2012-03-01

    3Dme are creative 3D digital story-tellers with a passion for making complex health and medical information comprehensible. They have an enviable ability to understand a broad range of health and medical topics and present them in an accurate and visually engaging manner. '3Dme - A Look Inside' is a privately owned 3D visualisation and multimedia company established by Luke and Sonya Brannelly in 2006. 3Dme are passionate about creating beautiful, scientifically accurate, relevant, high definition, full 3D visualisation presentations to take a look inside the human body to communicate a health or medical education message via engaging, creative digital story-telling. 3Dme's primary objective is to 'improve global health and education outcomes'. Winning a number of local and international awards for their work, they are well on their way to achieving this. 3Dme's vision is simply to use their scientific and artistic skills along with the reach of the internet and digital technology, to captivate, engage and inspire everyone from primary school students, teachers and parents, through to university undergraduates, academics and medical specialists, to improve their understanding of complex health and medical topics. The digital output of their 3D presentations is suitable for a variety of delivery platforms and includes e-learning modules, blended learning, interactive learning modules and Apps. 3Dme has made, and continues to make, significant investments in technology based hardware and software, boasting one of the largest in-house, fully equipped animation render farms in Queensland, Australia.

  4. Project to support formation of an energy and environment technology demonstration project in fiscal 1999. International joint demonstration and research project (Sichuan Province natural gas DME project); 1999 nendo Shisensho tennen gas DME project seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    DME can be manufactured from such raw materials as natural gas, coal bed gas and coal. NKK who is developing a technology to synthesize efficiently the DME being a new energy has been commissioned from NEDO to investigate and study a project to manufacture DME using natural gas produced in Sinchuan Province, and utilize it as fuel for power generation, transportation and LPG substitution. In the present research, the DME manufacturing plant size was assumed to be 500 tons a day (165 x 10{sup 3} tons annually). This output nearly corresponds to the current LPG consumption. The required amount of natural gas as the raw material is 0.2 x 10{sup 9} Nm{sup 3}/year, wherein, since the total production quantity of natural gas in Sinchuan Province is 10 x 10{sup 9} Nm{sup 3}/year, there is no problem in the supply of natural gas as the raw material. The construction cost was estimated to be 11 billion yen taking into consideration the device fabrication cost and construction labor cost in China. Furthermore, as a result of discussing the economy considering the natural gas material cost, industrial water cost, and labor cost for plant operation, the internal profit rate for the total capital after tax was found a little over 10%, proving the project to have excellent economic performance. (NEDO)

  5. Impact of Baseline Central Retinal Thickness on Outcomes in the VIVID-DME and VISTA-DME Studies

    Directory of Open Access Journals (Sweden)

    Edoardo Midena

    2018-01-01

    Full Text Available Purpose. To report the impact of baseline central retinal thickness (CRT on outcomes in patients with diabetic macular edema (DME in VIVID-DME and VISTA-DME. Methods. Post hoc analyses of two randomized controlled trials in which 862 DME patients were randomized 1 : 1 : 1 to treatment with intravitreal aflibercept 2.0 mg every 4 weeks (2q4, intravitreal aflibercept 2.0 mg every 8 weeks after five initial monthly doses (2q8, or macular laser photocoagulation at baseline and as needed. We compared visual and anatomical outcomes in subgroups of patients with baseline CRT < 400 μm and ≥400 μm. Results. At weeks 52 and 100, outcomes with intravitreal aflibercept 2q4 and 2q8 were superior to those in laser control-treated patients regardless of baseline CRT. When looked at in a binary fashion, the treatment effect of intravitreal aflibercept versus laser was not significantly better in the ≥400 μm than the <400 μm group; when looked at as a continuous variable, baseline CRT seemed to have an impact on the treatment effect of intravitreal aflibercept versus laser. Conclusions. Post hoc analyses of VIVID-DME and VISTA-DME demonstrated the benefits of intravitreal aflibercept treatment in DME patients with baseline CRT < 400 μm and ≥400 μm. This trial is registered with NCT01331681 and NCT01363440.

  6. Pra Desain Pabrik Dimethyl Ether (DME dari Gas Alam

    Directory of Open Access Journals (Sweden)

    Ajeng Puspitasari Yudiputri

    2014-09-01

    Full Text Available Berdasarkan data PT Pertamina (Persero, total konsumsi LPG 2008 mencapai 1,85 juta ton dan 600.000 ton di antaranya untuk program konversi. Pada 2009 kebutuhan LPG akan meningkat menjadi 3,67 juta ton dan 2 juta ton di antaranya untuk program konversi sampai akhir tahun. Namun, sumber pasokan LPG dari dalam negeri diperkirakan tidak akan beranjak dari angka 1,8 juta ton per tahun dalam beberapa tahun mendatang. Sehingga, Indonesia harus menutup kebutuhan dengan mengimpor LPG dalam jumlah cukup besar. Maka dari itu dibutuhkan bahan bakar gas lain yang mampu mengatasi permasalahan yang ditimbulkan tersebut. Dimethyl Ether (DME merupakan senyawa ether yang paling sederhana dengan rumus kimia CH3OCH3. Produksi DME dapat dihasilkan melalui sintesis gas alam. DME berbentuk gas yang tidak berwarna pada suhu ambien, zat kimia yang stabil, dengan titik didih -25,1oC. Tekanan uap DME sekitar 0,6 Mpa pada 25oC dan dapat dicairkan seperti halnya LPG. Viskositas DME 0,12-0,15 kg/ms, setara dengan viskositas propana dan butane (konstituen utama LPG, sehingga infrastruktur untuk LPG dapat juga digunakan untuk DME. Berdasarkan data Departemen ESDM pada Januari 2012, total cadangan gas alam Indonesia tercatat mencapai 150,70 Trillion Square Cubic Feet (TSCF. Berdasarkan jumlah tersebut, sebanyak 103,35 TSCF merupakan gas alam terbukti, sementara 47,35 TSCF sisanya masih belum terbukti. Berdasarkan hal tersebut, diketahui bahwa senyawa DME merupakan senyawa yang sesuai untuk bahan substitusi LPG. Dan ditinjau dari analisa ekonomi, didapatkan besar Investasi : $ 636,447,074.69 ; Internal Rate of Return\t: 20.51%; POT: 4.13 tahun; BEP : 37.36 %; dan NPV 10 year : $ 518,848,692. Dari ketiga parameter sensitifitas yaitu fluktuasi biaya investasi, harga bahan baku, dan harga jual dari produk, terlihat bahwa ketiganya tidak memberikan pengaruh yang cukup signifikan terhadap kenaikan atau penurunan nilai IRR pabrik. Sehingga pabrik DME dari Gas Alam ini layak untuk

  7. A Direct DME High Temperature PEM Fuel Cell

    DEFF Research Database (Denmark)

    Vassiliev, Anton; Jensen, Jens Oluf; Li, Qingfeng

    2012-01-01

    Dimethyl ether (DME) has been identified as an alternative to methanol for use in direct fuel cells. It combines the advantages of hydrogen in terms of pumpless fuel delivery and high energy density like methanol, but without the toxicity of the latter. The performance of a direct dimethyl ether...... fuel cell suffers greatly from the very low DME-water miscibility. To cope with the problem polybenzimidazole (PBI) based membrane electrode assemblies (MEAs) have been made and tested in a vapor fed system. PtRu on carbon has been used as anode catalyst and air at ambient pressure was used as oxidant...

  8. A Mixing Based Model for DME Combustion in Diesel Engines

    DEFF Research Database (Denmark)

    Bek, Bjarne H.; Sorenson, Spencer C.

    1998-01-01

    A series of studies has been conducted investigating the behavior of di-methyl ether (DME) fuel jets injected into quiescent combus-tion chambers. These studies have shown that it is possible to make a good estimate of the penetration of the jet based on existing correlations for diesel fuel......, by using appropriate fuel properties. The results of the spray studies have been incorporated into a first generation model for DME combustion. The model is entirely based on physical mixing, where chemical processes have been assumed to be very fast in relation to mixing. The assumption was made...

  9. A mixing based model for DME combustion in diesel engines

    DEFF Research Database (Denmark)

    Bek, Bjarne Hjort; Sorenson, Spencer C

    2001-01-01

    A series of studies has been conducted investigating the behavior of di-methyl ether (DME) fuel jets injected into quiescent combustion chambers. These studies have shown that it is possible to make a good estimate of the penetration of the jet based on existing correlations for diesel fuel......, by using appropriate fuel properties. The results of the spray studies have been incorporated into a first generation model for DME combustion. The model is entirely based on physical mixing, where chemical processes have been assumed to be very fast in relation to mixing. The assumption was made...

  10. Lubrication and wear in diesel engine injection equipment fuelled by dimethyl ether (DME)

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius

    2003-01-01

    Dimethyl ether (DME) has been recognised as an excellent fuel for diesel engines for over one decade now. DME fueled engines emit virtually no particulate matter even at low NOx levels. DME has thereby the potential of reducing the diesel engine emissions without filters or other devices...... that jeopardise the high efficiency of the engine and increase the manufacturing costs. DME has a low toxicity and can be made from anything containing carbon including biomass. If DME is produced from cheap natural gas from remote locations, the price of this new fuel could even become lower than that of diesel...... oil. Fueling diesel engines with DME presents two significant problems: The injection equipment can break down due to extensive wear and DME attacks nearly all known elastomers. The latter problem renders dynamic sealing diƣult whereas the first one involves the poor lubrication qualities of DME which...

  11. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethylether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operation in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation institute's test track facility near the University Park airport. After modification and optimization of the system on the bus, operation on the campus shuttle route began in early June 2002. However, the

  12. 14 CFR 171.321 - DME and marker beacon performance requirements.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false DME and marker beacon performance... (MLS) § 171.321 DME and marker beacon performance requirements. (a) The DME equipment must meet the..._regulations/ibr_locations.html. (b) MLS marker beacon equipment must meet the performance requirements...

  13. Applicability of dimethyl ether (DME) in a compression ignition engine as an alternative fuel

    International Nuclear Information System (INIS)

    Park, Su Han; Lee, Chang Sik

    2014-01-01

    Highlights: • Overall characteristics of DME fueled engine are reviewed. • Fuel properties characteristics of DME are introduced. • New technologies for DME vehicle are systemically reviewed. • Research trends for the development of DME vehicle in the world are introduced. - Abstract: From the perspectives of environmental conservation and energy security, dimethyl-ether (DME) is an attractive alternative to conventional diesel fuel for compression ignition (CI) engines. This review article deals with the application characteristics of DME in CI engines, including its fuel properties, spray and atomization characteristics, combustion performance, and exhaust emission characteristics. We also discuss the various technological problems associated with its application in actual engine systems and describe the field test results of developed DME-fueled vehicles. Combustion of DME fuel is associated with low NO x , HC, and CO emissions. In addition, PM emission of DME combustion is very low due to its molecular structure. Moreover, DME has superior atomization and vaporization characteristics than conventional diesel. A high exhaust gas recirculation (EGR) rate can be used in a DME engine to reduce NO x emission without any increase in soot emission, because DME combustion is essentially soot-free. To decrease NO x emission, engine after-treatment devices, such as lean NO x traps (LNTs), urea-selective catalytic reduction, and the combination of EGR and catalyst have been applied. To use DME fuel in automotive vehicles, injector design, fuel feed pump, and the high-pressure injection pump have to be modified, combustion system components, including sealing materials, have to be rigorously designed. To use DME fuel in the diesel vehicles, more research is required to enhance its calorific value and engine durability due to the low lubricity of DME, and methods to reduce NO x emission are also required

  14. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. Their strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis (FMEA, referred to by Air Products as a ''HAZOP'' analysis) with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operational in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation Institute's test track facility near the University Park airport. After modification and optimization of the system on

  15. Modified Two-Step Dimethyl Ether (DME Synthesis Simulation from Indonesian Brown Coal

    Directory of Open Access Journals (Sweden)

    Dwiwahju Sasongko

    2016-08-01

    Full Text Available A theoretical study was conducted to investigate the performance of dimethyl ether (DME synthesis from coal. This paper presents a model for two-step DME synthesis from brown coal represented by the following processes: drying, gasification, water-gas reaction, acid gas removal, and DME synthesis reactions. The results of the simulation suggest that a feedstock ratio of coal : oxygen : steam of 1 : 0.13 : 0.821 produces the highest DME concentration. The water-gas reactor simulation at a temperature of 400°C and a pressure of 20 bar gave the ratio of H2/CO closest to 2, the optimal value for two-step DME synthesis. As for the DME synthesis reactor simulation, high pressure and low temperature promote a high DME concentration. It is predicted that a temperature of 300°C and a pressure of 140 bar are the optimum conditions for the DME synthesis reaction. This study also showed that the DME concentration produced by the two-step route is higher than that produced by one-step DME synthesis, implying that further improvement and research are needed to apply two-step DME synthesis to production of this liquid fuel.

  16. Amperometric estimation of La3+ and Ce3+ with cupferron using d.m.e

    International Nuclear Information System (INIS)

    Pitre, K.S.; Lavale, S.C.

    1982-01-01

    Cupferron has been employed as a reagent for the amperometric titrations of La 3+ and Ce 3+ in very dilute solution using d.m.e. Hydrochloric acid (pH=2.75) has been used as supporting electrolyte. These titrations revealed cupferron to metal ratio of 1:1. Titrations are not hampered by the presence of a fairly large amount of Li + , Na + , K + , Mg 3+ , Zn 3+ , Al 3+ , Cl - , Br - , I - , NO 3 - , NO 2 - , CH 2 COO - and ClO 4 - ions. Furthermore, micro and ultramicro quantities of La 3+ and Ce 2+ have been successfully determined with an error of less than +- 0.70%. (author)

  17. SFOL Pulse: A High Accuracy DME Pulse for Alternative Aircraft Position and Navigation

    Directory of Open Access Journals (Sweden)

    Euiho Kim

    2017-09-01

    Full Text Available In the Federal Aviation Administration’s (FAA performance based navigation strategy announced in 2016, the FAA stated that it would retain and expand the Distance Measuring Equipment (DME infrastructure to ensure resilient aircraft navigation capability during the event of a Global Navigation Satellite System (GNSS outage. However, the main drawback of the DME as a GNSS back up system is that it requires a significant expansion of the current DME ground infrastructure due to its poor distance measuring accuracy over 100 m. The paper introduces a method to improve DME distance measuring accuracy by using a new DME pulse shape. The proposed pulse shape was developed by using Genetic Algorithms and is less susceptible to multipath effects so that the ranging error reduces by 36.0–77.3% when compared to the Gaussian and Smoothed Concave Polygon DME pulses, depending on noise environment.

  18. Dimethyl Ether (DME) - Development and Test of the New Volatile Fuel Tribo-Tester VFTT

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Sorenson, Spencer C; Moeller, P.

    2002-01-01

    of DME is significantly reduced then. As a result of the above, the work described in this paper was initiated. It introduces the search for materials that can cope with the properties of pure DME. In order to do so, a method capable of testing materials in DME was developed: The new volatile fuel tribo......: The lubricity and the viscosity. In former works these properties of DME were established to be very low. They can be raised by additising DME so that it acquires the same physical properties as diesel oil. In this case the DME blend is mainly composed of additive though. This means that the emission advantage....... These parameters are then compared with those obtained for diesel oil lubricating two steel surfaces in order to establish whether the chosen materials will ensure full lifetime of the injection equipment....

  19. Dimethyl Ether (DME) Assessment of Viscosity Using the New Volatile Fuel Viscometer (VFVM)

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Sorenson, Spencer C; Jakobsen, J.

    2001-01-01

    This paper describes the development and test of a viscometer capable of handling dimethyl Ether (DME) and other volatile fuels. DME has excellent combustion characteristics in diesel engines but the injection equipment can break down prematurely due to extensive wear when handling this fuel. It ...... is present in very large proportions. It is not believed that reasonably additised DME can reach the same viscosity and lubricity as diesel oil. The solution is rather to design the pumps so they can handle pure DME.......This paper describes the development and test of a viscometer capable of handling dimethyl Ether (DME) and other volatile fuels. DME has excellent combustion characteristics in diesel engines but the injection equipment can break down prematurely due to extensive wear when handling this fuel...

  20. ZERO-DIMENSIONAL MODEL OF A DIMETHYL ETHER (DME) PLANT BASED ON GASIFICATION OF TORREFIED BIOMASS

    DEFF Research Database (Denmark)

    Clausen, Lasse Røngaard; Elmegaard, Brian; Houbak, Niels

    2009-01-01

    similar to coal, which enables the use of commercially available coal gasification processing equipment. The DME plant model is integrated with a steam cycle that utilizes waste heat from the plant and covers the on-site electricity consumption. The plant model predicts a fuel production efficiency of 67...... % (LHV) from torrefied biomass to DME and 70 % (LHV) if the exported electricity is included. When accounting for raw, untreated biomass, the efficiency for DME production is reduced to about 60 %....

  1. Synthesis and molecular structure of YbI(bipy)(DME)2 complex

    International Nuclear Information System (INIS)

    Petrovskaya, T.V.; Fedyushkin, I.L.; Nevodchikov, V.I.; Bochkarev, M.N.; Borodina, N.V.; Eremenko, I.L.; Nefedov, S.E.

    1998-01-01

    The reaction of the ytterbium naphthaline complex [Yb(DME) 2 ] 2 (μ-C 10 H 8 ) with 2,2 ' -bipyridine in DME is found to lead to the formation of the complex with the Yb 2+ atom, YbI(bipy)(DME) 2 (1) containing 2,2 ' -bipyridine radical anion. Complex 1 is characterized by IR and UV spectroscopy, magnetic methods and X-ray analysis [ru

  2. Lubricity Additives and Wear with DME in Diesel Injection Pumps

    DEFF Research Database (Denmark)

    Nielsen, Kasper; Sorenson, Spencer C.

    1999-01-01

    In recent years it has been demonstrated that Dimethyl Ether (DME) possess many characteristics that could make it a successful alternative to diesel in the next century. High wear of the fuel injection system has been reported. This is caused by lack of natural protective constituents of Dimethyl...... wear of standard diesel jerk pump plungers elements were made with weight measurements, diameter measurements, 2-D and 3-D surface roughness measurements, and photography by a Michelson interferometer. Several lubricity additives were tested, but none reduced wear levels to those for diesel fuel...

  3. Life cycle GHG analysis of rice straw bio-DME production and application in Thailand

    International Nuclear Information System (INIS)

    Silalertruksa, Thapat; Gheewala, Shabbir H.; Sagisaka, Masayuki; Yamaguchi, Katsunobu

    2013-01-01

    Highlights: • Life cycle GHG emissions of rice straw bio-DME production in Thailand are assessed. • Bio-DME replaces diesel in engines and supplements LPG for household application. • Rice straw bio-DME in both cases of substitution helps reduce GHG emissions. - Abstract: Thailand is one of the leading countries in rice production and export; an abundance of rice straw, therefore, is left in the field nowadays and is commonly burnt to facilitate quick planting of the next crop. The study assesses the life cycle greenhouse gas (GHG) emissions of using rice straw for bio-DME production in Thailand. The analysis is divided into two scenarios of rice straw bio-DME utilization i.e. used as automotive fuel for diesel engines and used as LPG supplement for household application. The results reveal that that utilization of rice straw for bio-DME in the two scenarios could help reduce GHG emissions by around 14–70% and 2–66%, respectively as compared to the diesel fuel and LPG substituted. In case rice straw is considered as a by-product of rice cultivation, the cultivation of rice straw will be the major source of GHG emission contributing around 50% of the total GHG emissions of rice straw bio-DME production. Several factors that can affect the GHG performance of rice straw bio-DME production are discussed along with measures to enhance GHG performance of rice straw bio-DME production and utilization

  4. Design of novel DME/methanol synthesis plants based on gasification of biomass

    DEFF Research Database (Denmark)

    Clausen, Lasse Røngaard

    -scale DME plants based on gasification of torrefied biomass. 2. Small-scale DME/methanol plants based on gasification of wood chips. 3. Alternative methanol plants based on electrolysis of water and gasification of biomass. The plants were modeled by using the component based thermodynamic modeling...... why the differences, in biomass to DME/methanol efficiency, between the small-scale and the large-scale plants, showed not to be greater, was the high cold gas efficiency of the gasifier used in the small-scale plants (93%). By integrating water electrolysis in a large-scale methanol plant, an almost...... large-scale DME plant) to 63%, due to the relatively inefficient electrolyser....

  5. Short-Term Operations Plan for Collection of Bulk Quantity CBP Liquid in Support of a Pilot-Scale Treatabilty Evaluation with Water Recovery Inc

    Science.gov (United States)

    June 3, 2011 work plan for a pilot-scale treatability evaluation with a commercial wastewater treatment facility, Water Recovery Inc. (WRI) located in Jacksonville, Florida. Region ID: 04 DocID: 10749927, DocDate: 06-03-2011

  6. Cost estimation of hydrogen and DME produced by nuclear heat utilization system II

    International Nuclear Information System (INIS)

    Shiina, Yasuaki; Nishihara, Tetsuo

    2004-09-01

    Utilization and production of hydrogen has been studied in order to spread utilization of the hydrogen energy in 2020 or 2030. It will take, however, many years for the hydrogen energy to be used very easily like gasoline, diesel oil and city gas in the world. During the periods, low CO 2 release liquid fuels would be used together with hydrogen. Recently, di-methyl-ether (DME). has been noticed as one of the substitute liquid fuels of petroleum. Such liquid fuels can be produced from the mixed gas such as hydrogen and carbon oxide which are produced from natural gas by steam reforming. Therefore, the system would become one of the candidates of future system of nuclear heat utilization. Following the study in 2002, we performed economic evaluation of the hydrogen and DME production by nuclear heat utilization plant where heat generated by HTGR is completely consumed for the production. The results show that hydrogen price produced by nuclear was about 17% cheaper than the commercial price by increase in recovery rate of high purity hydrogen with increased in PSA process. Price of DME in indirect method produced by nuclear heat was also about 17% cheaper than the commercial price by producing high purity hydrogen in the DME producing process. As for the DME, since price of DME produced near oil land in petroleum exporting countries is cheaper than production in Japan, production of DME by nuclear heat in Japan has disadvantage economically in this time. Trial study to estimate DME price produced by direct method was performed. From the present estimation, utilization of nuclear heat for the production of hydrogen would be more effective with coupled consideration of reduction effect of CO 2 release. (author)

  7. Direct dimethyl-ether (DME) synthesis by spatial patterned catalyst arrangement. A modeling and simulation study

    Energy Technology Data Exchange (ETDEWEB)

    McBride, K.; Turek, T.; Guettel, R. [Clausthal Univ. of Technology (Germany). Inst. of Chemical Process Engineering

    2011-07-01

    The effect of spatially patterned catalyst beds was investigated for direct DME synthesis from synthesis gas as an example. A layered arrangement of methanol synthesis and dehydration catalyst was chosen and studied by numerical simulation under typical operating conditions for single-step DME synthesis. It was revealed that catalyst layers significantly influence the DME productivity. With an increasing number of layers from 2 to 40, an increase in DME productivity was observed approaching the performance of a physical catalyst mixture for an infinite number of layers. The results prove that a physical mixture of methanol synthesis and dehydration catalyst achieves the highest DME productivity under operating conditions chosen in this study. This can be explained by the higher average methanol concentration for the layered catalyst arrangement and thus stronger equilibrium constraints for the methanol synthesis reaction. Essentially, the layered catalyst arrangement is comparable to a cascade model of the two-step process, which is less efficient in terms of DME yield than the single-step process. However, since a significant effect was found, the layered catalyst arrangement could be beneficial for other reaction systems. (orig.)

  8. An Experimental Study of the Dimethyl Ether (DME) General Spary Characteristic%二甲基醚(DME)喷雾一般特性的试验研究

    Institute of Scientific and Technical Information of China (English)

    尧命发; 许斯都; 金萍; 王贺武; 周龙保

    2001-01-01

    This paper i ntroduces the authors primary research results of the study of the DME spray cha r acteristics under high fuel injection pressure.This work investigated the genera l nature of DME injection for engine-like conditions in a constant volume combu stion chamber.With the KODAK MotionCorder Analyzer,high speed motion pictures ha ve been obtained.The results showed that the spray penetration of the DME was sl ower than that of diesel fuel,and the spray angle of the DME was wider than that of the diesel fuel.Compared with the diesel fuel spray,the DME evaporated much more rapidly in the free spray development,and the influence of the ambient gas p ressure to the spray characteristics seemed the same as the diesel spray.The spr ay penetration decreased at high ambient pressure,but the spray angle increased at the same time.Near the chamber wall and impingement spray,the spray angle of the diesel fuel spray increased very fast,but that of the DME spray almost had no significant change.%介绍了在高压环境下对二甲基醚(DME)喷雾一般特性的试验研究结果,并与柴油的 喷雾特性进行了比较。试验研究是在定容燃烧弹上进行的,用阴影法通过高速数字摄影机拍 摄了二甲基醚和柴油的喷雾发展过程,应用计算机图像处理进行喷雾过程图像再现。研究结 果表明:DME的喷雾贯穿距离比柴油小,喷雾锥角比柴油大;在喷雾自由发展过程中,DME的 蒸 发速度比柴油快;环境密度对DME喷雾特性的影响与柴油相似,即密度增大,锥角增大, 贯穿距离减小。在燃烧室壁面附近,柴油的喷雾锥角迅速增大,而DME喷雾锥角几乎没有明 显的变化。

  9. Direct dimethyl ether (DME) synthesis through a thermally coupled heat exchanger reactor

    International Nuclear Information System (INIS)

    Vakili, R.; Pourazadi, E.; Setoodeh, P.; Eslamloueyan, R.; Rahimpour, M.R.

    2011-01-01

    Compared to some of the alternative fuel candidates such as methane, methanol and Fischer-Tropsch fuels, dimethyl ether (DME) seems to be a superior candidate for high-quality diesel fuel in near future. The direct synthesis of DME from syngas would be more economical and beneficial in comparison with the indirect process via methanol synthesis. Multifunctional auto-thermal reactors are novel concepts in process intensification. A promising field of applications for these concepts could be the coupling of endothermic and exothermic reactions in heat exchanger reactors. Consequently, in this study, a double integrated reactor for DME synthesis (by direct synthesis from syngas) and hydrogen production (by the cyclohexane dehydrogenation) is modelled based on the heat exchanger reactors concept and a steady-state heterogeneous one-dimensional mathematical model is developed. The corresponding results are compared with the available data for a pipe-shell fixed bed reactor for direct DME synthesis which is operating at the same feed conditions. In this novel configuration, DME production increases about 600 Ton/year. Also, the effects of some operational parameters such as feed flow rates and the inlet temperatures of exothermic and endothermic sections on reactor behaviour are investigated. The performance of the reactor needs to be proven experimentally and tested over a range of parameters under practical operating conditions.

  10. Artificial versus Natural Reuse of CO2 for DME Production: Are We Any Closer?

    Directory of Open Access Journals (Sweden)

    Mariano Martín

    2017-04-01

    Full Text Available This work uses a mathematical optimization approach to analyze and compare facilities that either capture carbon dioxide (CO2 artificially or use naturally captured CO2 in the form of lignocellulosic biomass toward the production of the same product, dimethyl ether (DME. In nature, plants capture CO2 via photosynthesis in order to grow. The design of the first process discussed here is based on a superstructure optimization approach in order to select technologies that transform lignocellulosic biomass into DME. Biomass is gasified; next, the raw syngas must be purified using reforming, scrubbing, and carbon capture technologies before it can be used to directly produce DME. Alternatively, CO2 can be captured and used to produce DME via hydrogenation. Hydrogen (H2 is produced by splitting water using solar energy. Facilities based on both photovoltaic (PV solar or concentrated solar power (CSP technologies have been designed; their monthly operation, which is based on solar availability, is determined using a multi-period approach. The current level of technological development gives biomass an advantage as a carbon capture technology, since both water consumption and economic parameters are in its favor. However, due to the area required for growing biomass and the total amount of water consumed (if plant growing is also accounted for, the decision to use biomass is not a straightforward one.

  11. Study of emissions for a compression ignition engine fueled with a mix of DME and diesel

    Science.gov (United States)

    Jurchiş, Bogdan; Nicolae, Burnete; Călin, Iclodean; Nicolae Vlad, Burnete

    2017-10-01

    Currently, there is a growing demand for diesel engines, primarily due to the relatively low fuel consumption compared to spark-ignition engines. However, these engines have a great disadvantage in terms of pollution because they produce solid particles that ultimately form particulate matter (PM), which has harmful effects on human health and also on the environment. The toxic emissions from the diesel engine exhaust, like particulate matter (PM) and NOx, generated by the combustion of fossil fuels, lead to the necessity to develop green fuels which on one hand should be obtained from regenerative resources and on the other hand less polluting. In this paper, the authors focused on the amount of emissions produced by a diesel engine when running with a fuel mixture consisting of diesel and DME. Dimethyl ether (DME) is developed mainly by converting natural gas or biomass to synthesis gas (syngas). It is an extremely attractive resource for the future used in the transport industry, given that it can be obtained at low costs from renewable resources. Using DME mixed with diesel for the combustion process, besides the fact that it produces less smoke, the emission levels of particulate matter is reduced compared to diesel and in some situations, NOx emissions may decrease. DME has a high enough cetane number to perform well as a compression-ignition fuel but due to the poor lubrication and viscosity, it is difficult to be used as the main fuel for combustion

  12. Cost estimation of hydrogen and DME produced by nuclear heat utilization system. Joint research

    International Nuclear Information System (INIS)

    Shiina, Yasuaki; Nishihara, Tetsuo

    2003-09-01

    Research of hydrogen energy has been performed in order to spread use of the hydrogen energy in 2020 or 2030. It will take, however, many years for the hydrogen energy to be used very easily like gasoline, diesel oil and city gas in all of countries. During the periods, low CO 2 release liquid fuels would be used together with hydrogen. Recently, di-methyl-either (DME) has been noticed as one of the substitute liquid fuels of petroleum. Such liquid fuels can be produced from the mixed gas such as hydrogen and carbon oxide which are produced by steam reforming hydrogen generation system by the use of nuclear heat. Therefore, the system would be one of the candidates of future system of nuclear heat utilization. In the present study, we focused on the production of hydrogen and DME. Economic evaluation was estimated for hydrogen and DME production in commercial and nuclear heat utilization plant. At first, heat and mass balance of each process in commercial plant of hydrogen production was estimated and commercial prices of each process were derived. Then, price was estimated when nuclear heat was used instead of required heat of commercial plant. Results showed that the production prices produced by nuclear heat were cheaper by 10% for hydrogen and 3% for DME. With the consideration of reduction effect of CO 2 release, utilization of nuclear heat would be more effective. (author)

  13. Thermodynamic approach and comparison of two-step and single step DME (dimethyl ether) syntheses with carbon dioxide utilization

    International Nuclear Information System (INIS)

    Chen, Wei-Hsin; Hsu, Chih-Liang; Wang, Xiao-Dong

    2016-01-01

    DME (Dimethyl ether) synthesis from syngas with CO_2 utilization through two-step and single step processes is analyzed thermodynamically. The influences of reaction temperature, H_2/CO molar ratio, and CO_2/CO molar ratio on CO and CO_2 conversions, DME selectivity and yield, and thermal behavior are evaluated. Particular attention is paid to the comparison of the performance of DME synthesis between the two different methods. In the two-step method, the addition of CO_2 suppresses the CO conversion during methanol synthesis. An increase in CO_2/CO ratio decreases the CO_2 conversion (negative effect), but increases the total consumption amount of CO_2 (positive effect). At a given reaction temperature with H_2/CO = 4, the maximum DME yield develops at CO_2/CO = 1. In the single step method, over 98% of CO can be converted and the DME yield can be as high as 0.52 mol (mol CO)"−"1 at CO_2/CO = 2. The comparison of the single step and two-step processes indicates that the maximum CO conversion, DME selectivity, and DME yield in the former are higher than those in the latter, whereas an opposite result in the maximum CO_2 conversion is observed. These results reveal that the single step process has lower thermodynamic limitation and is a better option for DME synthesis. From CO_2 utilization point of view, the operation with low temperature, high H_2/CO ratio, and low CO_2/CO ratio results in higher CO_2 conversion, irrespective of two-step or single step DME synthesis. - Highlights: • DME (Dimethyl ether) synthesis with CO_2 utilization is analyzed thermodynamically. • Single step and two-step DME syntheses are studied and compared with each other. • CO_2 addition suppresses CO conversion in MeOH synthesis but increases MeOH yield. • The performance of the single step DME synthesis is better than that of the two-step one. • Increase CO_2/CO ratio decreases CO_2 conversion but increases CO_2 consumption amount.

  14. Simple, Scalable, Script-based, Science Processor for Measurements - Data Mining Edition (S4PM-DME)

    Science.gov (United States)

    Pham, L. B.; Eng, E. K.; Lynnes, C. S.; Berrick, S. W.; Vollmer, B. E.

    2005-12-01

    The S4PM-DME is the Goddard Earth Sciences Distributed Active Archive Center's (GES DAAC) web-based data mining environment. The S4PM-DME replaces the Near-line Archive Data Mining (NADM) system with a better web environment and a richer set of production rules. S4PM-DME enables registered users to submit and execute custom data mining algorithms. The S4PM-DME system uses the GES DAAC developed Simple Scalable Script-based Science Processor for Measurements (S4PM) to automate tasks and perform the actual data processing. A web interface allows the user to access the S4PM-DME system. The user first develops personalized data mining algorithm on his/her home platform and then uploads them to the S4PM-DME system. Algorithms in C and FORTRAN languages are currently supported. The user developed algorithm is automatically audited for any potential security problems before it is installed within the S4PM-DME system and made available to the user. Once the algorithm has been installed the user can promote the algorithm to the "operational" environment. From here the user can search and order the data available in the GES DAAC archive for his/her science algorithm. The user can also set up a processing subscription. The subscription will automatically process new data as it becomes available in the GES DAAC archive. The generated mined data products are then made available for FTP pickup. The benefits of using S4PM-DME are 1) to decrease the downloading time it typically takes a user to transfer the GES DAAC data to his/her system thus off-load the heavy network traffic, 2) to free-up the load on their system, and last 3) to utilize the rich and abundance ocean, atmosphere data from the MODIS and AIRS instruments available from the GES DAAC.

  15. Socio-economic Effects of a Bio-DME Plant in Vaexjoe

    Energy Technology Data Exchange (ETDEWEB)

    Baudin, Anders; Nordvall, Hans-Olof

    2008-03-15

    The task described for CHRISGAS Work Package (WP) 16 (Socio-economic Studies) is to assess the likely short- and long-term effects on society in general and the forest sector in particular of a full-scale bio-DME plant in Vaexjoe. Bio-DME is an emission free substitute to diesel. Bio-DME can also be mixed with or constitute a substitute for LPG (Liquid Petroleum Gas). A full-scale bio-DME plant is expected to produce 400 000 tons annually with a raw material requirement in the order of 2.6 TWh. In our study we have also considered output levels at 200 000 and 100 000 tons, respectively. The essential issues investigated concern the raw material availability, investment cost, product prices and employment. In our study we limit the discussion on raw material for bio-DME to include logging residues and stumps. Despite this limitation we have to consider it from the whole context of the forest sector. The availability of logging residues and stumps is closely related to forest operations such as clear cuts, thinnings and clearings. Transport of raw material to Vaexjoe is considered within a distance of 150 km by road, 600 km by railroad and 10 000 km by sea. Although it can be argued that forest fuel is a commodity that can be transported over long distances, e. g. as chips, it has to be recognised that the vast majority raw material has to be found near the bio-DME plant. Therefore it is necessary to obtain a realistic view on what is available within road distance, i.e. within 150 km from Vaexjoe. Based on two independent data sources and considering only logging residues and stumps we find that the bio-DME plant in Vaexjoe to a large (or even full) extent can be supplied by logging residues and stumps in a radius of 150 km around Vaexjoe. From the aspect of competition of raw material the picture is more complicated. Logging residues and stumps will, to an increasing degree, be used by the thermal heating/power plants in south Sweden and, in addition, there is

  16. Radiation quantities and units

    International Nuclear Information System (INIS)

    2013-01-01

    This fifth chapter presents the conceptual evolution, the definition procedures, the radiological quantities themselves, the relation between them, the new operational quantities and the new quantities defined in the ICRP 60 that replaced ICRP 26 and was included in the CNEN-NN-3.01 standard of 2011

  17. Far-ultraviolet and visible observations of flares on dMe stars

    International Nuclear Information System (INIS)

    Bromage, G.E.; Patchett, B.E.; Phillips, K.J.H.

    1983-01-01

    Four large flare events - one on each of the dMe stars UV Cet, AT Mic, EV Lac and EQ Peg - have been witnessed during a total of 17 1/2 hours of far-UV (lambdalambda1150-1950) IUE exposures. Some observational characteristics of these four events are compared. Two showed strong enhancements of chromospheric and transition-region line strengths. The other two did not, even though their visible flares were intense (ΔU approx. 2 mag.). The brightest UV flare spectrum (EQ Peg) is contrasted with that of the largest solar flare seen from 'Skylab'. (Auth.)

  18. Broadband spectral observation of a dMe star radio flare

    International Nuclear Information System (INIS)

    Guedel, M.; Benz, A.O.; Fuerst, E.; Simett, G.M.; Davis, R.J.

    1989-01-01

    A flare on the dMe star AD Leonis was simultaneously observed with the radio telescopes in Effelsberg, Jodrell Bank, and Arecibo using spectrometers at 1665, 166 and 1415 MHz with bandwidths of 25, 100 and 40 MHz respectively. The time coincidence confirms the stellar origin of the radiation. The flare emission was resolved into a multitude of broadband pulsations. The e-folding rise and decay times were of the order of the time resolution of the Effelsberg data (125 ms), or less. The circular polarization was ∼ 100%. Similar bursts, but 4 orders of magnitude less powerful, have been observed from the sun at lower frequencies

  19. Strongly intensive quantities

    International Nuclear Information System (INIS)

    Gorenstein, M. I.; Gazdzicki, M.

    2011-01-01

    Analysis of fluctuations of hadron production properties in collisions of relativistic particles profits from use of measurable intensive quantities which are independent of system size variations. The first family of such quantities was proposed in 1992; another is introduced in this paper. Furthermore we present a proof of independence of volume fluctuations for quantities from both families within the framework of the grand canonical ensemble. These quantities are referred to as strongly intensive ones. Influence of conservation laws and resonance decays is also discussed.

  20. Impact of baseline Diabetic Retinopathy Severity Scale scores on visual outcomes in the VIVID-DME and VISTA-DME studies.

    Science.gov (United States)

    Staurenghi, Giovanni; Feltgen, Nicolas; Arnold, Jennifer J; Katz, Todd A; Metzig, Carola; Lu, Chengxing; Holz, Frank G

    2017-10-19

    To evaluate intravitreal aflibercept versus laser in subgroups of patients with baseline Diabetic Retinopathy Severity Scale (DRSS) scores ≤43, 47, and ≥53 in VIVID-DME and VISTA-DME. Patients with diabetic macular oedema were randomised to receive intravitreal aflibercept 2 mg every 4 weeks (2q4), intravitreal aflibercept 2 mg every 8 weeks after five initial monthly doses (2q8), or macular laser photocoagulation at baseline with sham injections at every visit. These post hoc analyses evaluate outcomes based on baseline DRSS scores in patients in the integrated dataset. The 2q4 and 2q8 treatment groups were also pooled. 748 patients had a baseline DRSS score based on fundus photographs (≤43, n=301; 47, n=153; ≥53, n=294). At week 100, the least squares mean difference between treatment groups (effect of intravitreal aflibercept above that of laser, adjusting for baseline best-corrected visual acuity) was 8.9 (95% CI 5.99 to 11.81), 9.7 (95% CI 5.54 to 13.91), and 11.0 (95% CI 7.96 to 14.1) letters in those with baseline DRSS scores ≤43, 47, and ≥53, respectively. The proportions of patients with ≥2 step DRSS score improvement were greater in the intravitreal aflibercept group versus laser, respectively, for those with baseline DRSS scores of ≤43 (13% vs 5.9%), 47 (25.8% vs 4.5%), and ≥53 (64.5% vs 28.4%). Regardless of baseline DRSS score, functional outcomes were superior in intravitreal aflibercept-treated patients, demonstrating consistent treatment benefit across various baseline levels of retinopathy. NCT01331681 and NCT01363440, Post-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  1. Laminar Flame Velocity and Temperature Exponent of Diluted DME-Air Mixture

    Science.gov (United States)

    Naseer Mohammed, Abdul; Anwar, Muzammil; Juhany, Khalid A.; Mohammad, Akram

    2017-03-01

    In this paper, the laminar flame velocity and temperature exponent diluted dimethyl ether (DME) air mixtures are reported. Laminar premixed mixture of DME-air with volumetric dilutions of carbon dioxides (CO2) and nitrogen (N2) are considered. Experiments were conducted using a preheated mesoscale high aspect-ratio diverging channel with inlet dimensions of 25 mm × 2 mm. In this method, flame velocities are extracted from planar flames that were stabilized near adiabatic conditions inside the channel. The flame velocities are then plotted against the ratio of mixture temperature and the initial reference temperature. A non-linear power law regression is observed suitable. This regression analysis gives the laminar flame velocity at the initial reference temperature and temperature exponent. Decrease in the laminar flame velocity and increase in temperature exponent is observed for CO2 and N2 diluted mixtures. The addition of CO2 has profound influence when compared to N2 addition on both flame velocity and temperature exponent. Numerical prediction of the similar mixture using a detailed reaction mechanism is obtained. The computational mechanism predicts higher magnitudes for laminar flame velocity and smaller magnitudes of temperature exponent compared to experimental data.

  2. Experimental study of a plat-flame micro combustor burning DME for thermoelectric power generation

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, L.Q.; Zhao, D.Q.; Guo, C.M.; Wang, X.H. [Key Laboratory of Renewable Energy and Gas Hydrate, CAS, Guangzhou Institute of Energy Conversion of CAS, Guangzhou 510640 (China)

    2011-01-15

    A centimeter magnitude thermoelectric (TE) power generation system based on a plat-flame micro combustor burning DME (dimethyl ether) has been developed. The chamber wall of this micro combustor was made of two parallel sintered porous plates which acted as mixture inlet. The main virtue of this combustor is that it can keep combustor wall at lower temperature for reducing heat loss when sustaining a stable flame. Experimental test results showed it was feasible to obtain stable DME/air premixed flame at lean combustion situations in the micro combustor. The combustion load of this 0.48 cm{sup 3} chamber capacity was 20-200 W at equivalence ratio {phi} = 0.6. Though the flame temperature was above 1000 C, the combustor's wall temperature was near 600 C lower than flame temperature. In the demonstrated TE power generation system which integrated the plat-flame micro combustor, a heat spreader had good effect on uniforming the hot side temperature field of TE modules. Cooled by water and with 150 W input power at {phi} = 0.7, the system produced 10 V output at open circuit and 4 V at 10 {omega} load. The maximum power output was above 2 W, and the maximum overall chemical-electric energy conversion efficiency was 1.25%. (author)

  3. Artificial versus Natural Reuse of CO2 for DME Production:Are We Any Closer?

    Institute of Scientific and Technical Information of China (English)

    Mariano Martin

    2017-01-01

    This work uses a mathematical optimization approach to analyze and compare facilities that either capturecarbon dioxide (CO2) artificially or use naturally captured COs in the form of lignocellulosic biomass towardthe production of the same product, dimethyl ether (DME). In nature, plants capture COs via photosynthesisin order to grow. The design of the first process discussed here is based on a superstructure optimizationapproach in order to select technologies that transform lignocellulosic biomass into DME. Biomass is gas-ified; next, the raw syngas must be purified using reforming, scrubbing, and carbon capture technologiesbefore it can be used to directly produce DME. Alternatively, CO2 can be captured and used to produce DMEvia hydrogenation. Hydrogen (H2) is produced by splitting water using solar energy. Facilities based on bothphotovoltaic (PV) solar or concentrated solar power (CSP) technologies have been designed; their monthlyoperation, which is based on solar availability, is determined using a multi-period approach. The currentlevel of technological development gives biomass an advantage as a carbon capture technology, since bothwater consumption and economic parameters are in its favor. However, due to the area required for growingbiomass and the total amount of water consumed (if plant growing is also accounted for), the decision to use biomass is not a straightforward one.

  4. Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills.

    Science.gov (United States)

    Naqvi, M; Yan, J; Fröling, M

    2010-02-01

    There is great interest in developing black liquor gasification technology over recent years for efficient recovery of bio-based residues in chemical pulp mills. Two potential technologies of producing dimethyl ether (DME) and methane (CH(4)) as alternative fuels from black liquor gasification integrated with the pulp mill have been studied and compared in this paper. System performance is evaluated based on: (i) comparison with the reference pulp mill, (ii) fuel to product efficiency (FTPE) and (iii) biofuel production potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH(4) production globally in terms of black liquor availability. BPP and FTPE of CH(4) production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill.

  5. Effects of DME mixing on number density and size properties of soot particles in counterflow non-premixed ethylene flames

    KAUST Repository

    Choi, J. H.; Choi, B. C.; Lee, S. M.; Chung, Suk-Ho; Jung, K. S.; Jeong, W. L.; Choi, S. K.; Park, S. K.

    2015-01-01

    In order to investigate the effect of DME mixing on the number density and size of soot particles, DME was mixed in a counter flow non-premixed ethylene flame with mixture ratios of 5%, 14% and 30%. A laser extinction/scattering technique has been adopted to measure the volume fraction, number density, and mean size of soot particles. The experimental results showed that the highest soot concentrations were observed for flames with mixture ratios of 5% and 14%; however, for a mixture ratio of 30% the soot concentration decreased. Numerical results showed that the concentrations of propargyl radicals (C3H3) at the 5% and 14% ratios were higher than those measured in the ethylene-based flame, and the production of benzene (C6H6) in the 5% and 14% DME mixture flames was also increased. This indicates the crucial role of propargyl in benzene ring formation. These reactions generally become stronger with increased DME mixing, except for A1- + H2 → A1 + H (-R554) and n-C4H5 + C2H2 → A1 + H (R542). Therefore, it is indicated that adding DME to ethylene flames promotes benzene ring formation. Note that although the maximum C6H6 concentration is largest in the 30% DME mixing flame, the soot volume fraction is smaller than those for the 5% and 14% mixture ratios. This is because the local C6H6 concentration decreases in the relatively low temperature region in the fuel side where soot growth occurs. © 2015, The Korean Society of Mechanical Engineers and Springer-Verlag Berlin Heidelberg.

  6. Effects of DME mixing on number density and size properties of soot particles in counterflow non-premixed ethylene flames

    KAUST Repository

    Choi, J. H.

    2015-05-01

    In order to investigate the effect of DME mixing on the number density and size of soot particles, DME was mixed in a counter flow non-premixed ethylene flame with mixture ratios of 5%, 14% and 30%. A laser extinction/scattering technique has been adopted to measure the volume fraction, number density, and mean size of soot particles. The experimental results showed that the highest soot concentrations were observed for flames with mixture ratios of 5% and 14%; however, for a mixture ratio of 30% the soot concentration decreased. Numerical results showed that the concentrations of propargyl radicals (C3H3) at the 5% and 14% ratios were higher than those measured in the ethylene-based flame, and the production of benzene (C6H6) in the 5% and 14% DME mixture flames was also increased. This indicates the crucial role of propargyl in benzene ring formation. These reactions generally become stronger with increased DME mixing, except for A1- + H2 → A1 + H (-R554) and n-C4H5 + C2H2 → A1 + H (R542). Therefore, it is indicated that adding DME to ethylene flames promotes benzene ring formation. Note that although the maximum C6H6 concentration is largest in the 30% DME mixing flame, the soot volume fraction is smaller than those for the 5% and 14% mixture ratios. This is because the local C6H6 concentration decreases in the relatively low temperature region in the fuel side where soot growth occurs. © 2015, The Korean Society of Mechanical Engineers and Springer-Verlag Berlin Heidelberg.

  7. Heterogeneous structure and solvation dynamics of DME/water binary mixtures: A combined spectroscopic and simulation investigation

    Science.gov (United States)

    Das Mahanta, Debasish; Rana, Debkumar; Patra, Animesh; Mukherjee, Biswaroop; Mitra, Rajib Kumar

    2018-05-01

    Water is often found in (micro)-heterogeneous environments and therefore it is necessary to understand their H-bonded network structure in such altered environments. We explore the structure and dynamics of water in its binary mixture with relatively less polar small biocompatible amphiphilic molecule 1,2-Dimethoxyethane (DME) by a combined spectroscopic and molecular dynamics (MD) simulation study. Picosecond (ps) resolved fluorescence spectroscopy using coumarin 500 as the fluorophore establishes a non-monotonic behaviour of the mixture. Simulation studies also explore the various possible H-bond formations between water and DME. The relative abundance of such different water species manifests the heterogeneity in the mixture.

  8. A Study on the Effects of Compression Ratio, Engine Speed and Equivalence Ratio on HCCI Combustion of DME

    DEFF Research Database (Denmark)

    Pedersen, Troels Dyhr; Schramm, Jesper

    2007-01-01

    An experimental study has been carried out on the homogeneous charge compression ignition (HCCI) combustion of Dimethyl Ether (DME). The study was performed as a parameter variation of engine speed and compression ratio on excess air ratios of approximately 2.5, 3 and 4. The compression ratio was...

  9. Phase behavior for the poly(alkyl methacrylate)+supercritical CO2+DME mixture at high pressures

    International Nuclear Information System (INIS)

    Choi, Yong-Seok; Chio, Sang-Won; Byun, Hun-Soo

    2016-01-01

    The phase behavior curves of binary and ternary system were measured for poly(alkyl methacrylate) in supercritical CO 2 , as well as for the poly(alkyl methacrylate)+dimethyl ether (DME) (or 1-butene) in CO 2 . The solubility curves are reported for the poly(alkyl methacrylate)+DME in supercritical CO 2 at temperature from (300 to 465) K and a pressure from (3.66 to 248) MPa. Also, The high-pressure static-type apparatus of cloud-point curve was tested by comparing the measured phase behavior data of the poly(methyl methacrylate) [PMMA]+CO 2 +20.0 and 30.4 wt% methyl methacrylate (MMA) system with literature data of 10.4, 28.8 and 48.4 wt% MMA concentration. The phase behavior data for the poly(alkyl methacrylate)+CO 2 +DME mixture were measured in changes of the pressure-temperature (p, T) slope and with DME concentrations. Also, the cloud-point pressure for the poly(alkyl methacrylate)+1- butene solution containing supercritical CO 2 shows from upper critical solution temperature (UCST) region to lower critical solution temperature (LCST) region at concentration range from (0.0 to 95) wt% 1-butene at below 455 K and at below 245MPa.

  10. 76 FR 13438 - AccessTel, Inc., American Asset Management Corp., DME Interactive Holdings, Inc., DocuPort, Inc...

    Science.gov (United States)

    2011-03-11

    ... SECURITIES AND EXCHANGE COMMISSION [File No. 500-1] AccessTel, Inc., American Asset Management Corp., DME Interactive Holdings, Inc., DocuPort, Inc., and iCarbon Corp., Order of Suspension of... Asset Management Corp. because it has not filed any periodic reports since the period ended March 31...

  11. Phase behavior for the poly(alkyl methacrylate)+supercritical CO{sub 2}+DME mixture at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Yong-Seok; Chio, Sang-Won; Byun, Hun-Soo [Chonnam National University, Yeosu (Korea, Republic of)

    2016-01-15

    The phase behavior curves of binary and ternary system were measured for poly(alkyl methacrylate) in supercritical CO{sub 2}, as well as for the poly(alkyl methacrylate)+dimethyl ether (DME) (or 1-butene) in CO{sub 2}. The solubility curves are reported for the poly(alkyl methacrylate)+DME in supercritical CO{sub 2} at temperature from (300 to 465) K and a pressure from (3.66 to 248) MPa. Also, The high-pressure static-type apparatus of cloud-point curve was tested by comparing the measured phase behavior data of the poly(methyl methacrylate) [PMMA]+CO{sub 2}+20.0 and 30.4 wt% methyl methacrylate (MMA) system with literature data of 10.4, 28.8 and 48.4 wt% MMA concentration. The phase behavior data for the poly(alkyl methacrylate)+CO{sub 2}+DME mixture were measured in changes of the pressure-temperature (p, T) slope and with DME concentrations. Also, the cloud-point pressure for the poly(alkyl methacrylate)+1- butene solution containing supercritical CO{sub 2} shows from upper critical solution temperature (UCST) region to lower critical solution temperature (LCST) region at concentration range from (0.0 to 95) wt% 1-butene at below 455 K and at below 245MPa.

  12. Quantities for environmental monitoring

    International Nuclear Information System (INIS)

    1989-01-01

    It is recommended that if measurements are made with the objective of monitor radiation levels in the environment to elucidate long-term changes in these levels, then air kerma should be used. If the objective is to give an indication that levels from man-made sources are acceptable within specified limits for the exposure of people, then ambient dose equivalent should be used. It should be noted that radiation risks to individuals are best expressed by the quantity effective dose equivalent. If this latter quantity is to be accurately assessed, it may be necessary to obtain details of the quality of the environmental radiation that cannot be described adequately by simple measurements of either air kerma or ambient dose equivalent. If the above objectives pertain, the measurements should record both air kerma and ambient dose equivalent. If neutrons are measured in the environment then ambient dose equivalent is the appropriate quantity for both the above objectives. (author)

  13. Emission sources and quantities

    International Nuclear Information System (INIS)

    Heinen, B.

    1991-01-01

    The paper examines emission sources and quantities for SO 2 and NO x . Natural SO 2 is released from volcanic sources and to a much lower extent from marsh gases. In nature NO x is mainly produced in the course of the chemical and bacterial denitrification processes going on in the soil. Manmade pollutants are produced in combustion processes. The paper concentrates on manmade pollution. Aspects discussed include: mechanism of pollution development; manmade emission sources (e.g. industry, traffic, power plants and domestic sources); and emission quantities and forecasts. 11 refs., 2 figs., 5 tabs

  14. Radiation quantities and units

    International Nuclear Information System (INIS)

    1980-01-01

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

  15. Demographic, medical and visual aspects of Dia- betic Retinopathy (DR and Diabetic Macular Edema (DME in South African diabetic patients*

    Directory of Open Access Journals (Sweden)

    Anusha Y. Sukha

    2009-12-01

    Full Text Available Objective: To investigate some of the demographic, medical, and visual aspects of diabetic retinopathy (DR and diabetic macula edema (DME in diabetics attending an urban clinic in Johannesburg, Gauteng. Design: In this cross-sectional study, 202 diabetic patients were recruited. Demographic variables included age, gender, race, age of diagnosis, duration of diabetes mellitus (DM, and social habits. Medical variables included systemic conditions present, blood pressures, body mass indices (BMI, lipid profiles, glycerated haemoglobin (HbA1c, and other biochemical data. Visual variables included distance, pinhole and near visual acuities, contrast visual acuities (CVA, refractive status, colour vision, central visual field evaluation with the Amsler grid, intraocular pressures (IOP, fundus photography and administration of the Impact of Visual Impairment (IVI questionnaire. All variables were compared between diabetic subjects with and with-out DR and DME in both right and left eyes. Results: Overall prevalence of DR was 22.8% and DME 12.5%. In DR subjects, significant results indicated that Whites were more likely to present with DR (p = 0.002. Subjects with DR had a higher mean duration of DM (p = 0.002 and a higher mean diastolic blood pressure (p = 0.035. Autorefraction suggested that more myopia and less astigmatism might be associated with DR. A higher mean CVA at the 2.5% level in DR was significant in both the right eyes (p = 0.042 and left eyes (p = 0.035. These subjects also reported a higher mean IVI score in the consumer and social interaction domain (p = 0.032. Similarly, DME subjects displayed a higher mean duration of DM (p = 0.042 and a higher mean diastolic blood pressure (p = 0.048. A higher mean CVA was associated at both the 10% level: right eyes (p = 0.021; and left eyes (p = 0.046, and at the 2.5% level: right eyes (p = 0.033 and left eyes (p = 0.045. A higher mean IVI score in leisure and work (p = 0.026, consumer and social

  16. Spray characteristics of dimethyl ether (D.M.E.) as on alternative fuel for diesel engine; Daitai diesel nenryo to shite no dimethyl ether (D.M.E.) no funmu tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, K; Nishida, K; Yoshizaki, T; Hiroyasu, H [Hiroshima University, Hiroshima (Japan)

    1997-10-01

    D.M.E. which was paid attention to as on alternative fuel for a diesel engine, was injected by using Bosch type injection pump and a hole nozzle into a high pressure and high temperature vessel. The spray was observed by using schlieren photography. Spray characteristics, such as, the tip penetration, the cone angle and the volume of the spray were and were compared with a diesel fuel spray. The following thing, and so on were found out as a results. The spray angle of the DME spray of atmosphere pressure Pa=0.1Mpa spreads out large in comparison with the diesel fuel spray, and the way of the change by the pressure is contrary to the case of the diesel fuel spray. 3 refs., 6 figs., 1 tab.

  17. IMPLEMENTATION OF DEMONSTRATION PLOTS DME NYAMPLUNG (Calophyllum inophyllum L IN BULUAGUNG AND PATUTREJO VILLAGES

    Directory of Open Access Journals (Sweden)

    Bambang Uripno

    2014-05-01

    Full Text Available   The purpose of this study were to evaluate the condition of the frist demplot DME nyamplung. Energy self sufficient village program aims to improve stock and diverse energy source and society economic opportunity. Nyamplung is very potential plant to be used as raw material of biofuel, because it has very high fat plant content and has not be used for food. The biofuel from nyamplung is a new innovation. Involvement of forest village community in biofuel industry development both as producers and as consumers is very important. Forestry Ministry has established demonstration plots in Buluagung and Patutrejo villages as a facilitation in developing biofuel nyamplung silvoindustry. Up to now, the demplots still faces some problems. The researh method was qualitatif analysis. Collecting data from 62 respondents using purposive sampling. Data were collected using questionnaires, field obsevation, and in-depth interview. Focus group discussion  was used to confirm the data from the respondents. Research results show that the demplots have not been developed through participatory approach. Involvement of community to demplots activity is low. Involvement of the village communities are significantly correlated to biofuel price, technology innovation, role of demplot and support from local leaders.  

  18. Effect of YangZheng XiaoJi Extract, DME-25, on endothelial cells and their response to Avastin.

    OpenAIRE

    Owen, Sioned; Gao, Y.; Zhi, X.; Wei, C.; Wu, Y.; Jiang, Wen Guo

    2016-01-01

    ackground: Angiogenesis is a cellular process that has been identified as a key target for therapy in solid cancer. However, over the course of anti-angiogenic therapies, cancer cells acquire resistance to these therapies after an initial period of success. DME-25 is an extract from Yang Zheng Xiao Ji, a traditional Chinese medicine that has been reported to benefit patients with cancer by alleviating chemotherapy-associated symptoms and possibly inhibiting key cancer cell traits. This study ...

  19. Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills

    Energy Technology Data Exchange (ETDEWEB)

    Raza, M.; Jinyue Yan (Dept. of Chemical Engineering and Technology/Energy Processes, Royal Institute of Technology, Stockholm (Sweden)). e-mail: rnaqvi@kth.se; Froeling, Morgan (Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (Sweden))

    2009-07-01

    The consumption of fossil fuels is rapidly increasing and there is an urgent need to develop technologies for renewable fuel production not only as alternatives but also as additional fuels. Efficient polygeneration of transportation fuels with heat and electricity is one of the innovative technologies which have potential to replace fossil fuels and mitigate climate change. Two potential technologies of producing dimethyl ether (DME) and methane (CH4) as alternative fuels integrated with black liquor gasification have been studied and compared in this paper. System performance is evaluated based on: (i) Comparison with the reference pulp mill, (ii) Fuel to product efficiency (FTPE) and (iii) Biofuel Production Potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH4 production globally in terms of black liquor availability. BPP and FTPE of CH4 production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill

  20. Technoeconomic analysis of a low CO2 emission dimethyl ether (DME) plant based on gasification of torrefied biomass

    DEFF Research Database (Denmark)

    Clausen, Lasse Røngaard; Elmegaard, Brian; Houbak, Niels

    2010-01-01

    rich stream to a CO2 capture plant, which is used in the conditioning of the syngas.The plant models predict energy efficiencies from torrefied biomass to DME of 66% (RC) and 48% (OT) (LHV). If the exported electricity is included, the efficiencies are 71% (RC) and 64% (OT). When accounting for energy...... loss in torrefaction, the total efficiencies are reduced to 64% (RC) and 58% (OT). The two plants produce DME at an estimated cost of $11.9/GJLHV (RC) and $12.9/GJLHV (OT). If a credit is given for storing the CO2 captured, the future costs may become as low as $5.4/GJLHV (RC) and $3.1/GJLHV (OT)....... process that takes place at 200–300°C. Torrefied biomass has properties similar to coal, which enables the use of commercially available coal gasification processing equipment. The DME plants are designed with focus on lowering the total CO2 emissions from the plants; this includes e.g. a recycle of a CO2...

  1. Flares on dMe stars: IUE and optical observations of At Mic, and comparison of far-ultraviolet stellar and solar flares

    International Nuclear Information System (INIS)

    Bromage, G.E.; Phillips, K.J.H.; Dufton, P.L.; Kingston, A.E.

    1986-01-01

    The paper concerns observations of a large flare event on the dMe star At Mic, detected by the International Ultraviolet Explorer. The far-ultraviolet spectra of the flare is compared with those of other stellar flares, and also with a large solar flare recorded by the Skylab mission in 1973. The quiescent-phase optical and ultraviolet spectrum of the same dMe flare star is discussed. (U.K.)

  2. Forage quantity and quality

    Science.gov (United States)

    Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

    2002-01-01

    The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

  3. Prices versus Quantities

    DEFF Research Database (Denmark)

    Hansen, Lars Gårn; Jensen, Frank

    illustrate that this result does not generalise to a search fishery, where marginal costs are allowed to depend on harvest. Hansen et al (2008) study a fishery where non-compliance with regulations is a problem. When the regulator is uncertain about non-compliance (compliance uncertainty), then landing fees......Weitzman (2002) studies the regulation of a fishery characterised by constant marginal harvest costs and shows that price regulation performs better than quantity regulation when the regulator is uncertain about the biological reproduction function (ecological uncertainty). Here, we initially...... are the preferred type of regulation, and Hansen et al (2008) find that this result does generalise to a search fishery where marginal costs depend on harvest. In this paper, we simulate a stochastic stock-recruitment model for the Danish cod fishery in the Kategat capturing both ecological and compliance...

  4. Allen's astrophysical quantities

    CERN Document Server

    2000-01-01

    This new, fourth, edition of Allen's classic Astrophysical Quantities belongs on every astronomer's bookshelf. It has been thoroughly revised and brought up to date by a team of more than ninety internationally renowned astronomers and astrophysicists. While it follows the basic format of the original, this indispensable reference has grown to more than twice the size of the earlier editions to accommodate the great strides made in astronomy and astrophysics. It includes detailed tables of the most recent data on: - General constants and units - Atoms, molecules, and spectra - Observational astronomy at all wavelengths from radio to gamma-rays, and neutrinos - Planetary astronomy: Earth, planets and satellites, and solar system small bodies - The Sun, normal stars, and stars with special characteristics - Stellar populations - Cataclysmic and symbiotic variables, supernovae - Theoretical stellar evolution - Circumstellar and interstellar material - Star clusters, galaxies, quasars, and active galactic nuclei ...

  5. Relativity of Electric Quantity

    Directory of Open Access Journals (Sweden)

    GAO Zhong-wen

    2017-04-01

    Full Text Available The demonstration foundation,which is used to demonstrate that observed values from the interaction force between two charges,which are not at the same point would be different in different reference frames,is that the transmission of the interaction between charges needs time. Firstly,this paper analyzes the foundation of hypothetical process that the electric field and the magnetic field are built by one charge,and then the electromagnetic field would be transferred to another charge in vacuo by the speed of light,and produces force. It points out that from the simultaneity of relativity,the force applied to charge would occur in different time in the different reference frames,the force would be neither in the same size nor in the opposite direction,and Newton’s Third Law is not valid longer, the deeper cause of these conclusions would be known. On this basis,this paper gives the basis that force would keep invariant in different reference frames,and according to this condition,with the situation of the charge that under the Coulombian force and electromagnetism,the relative form of expression and demonstration methods of electric quantity in different reference frames are given. On the basis of the hypothesis that force would keep invariant in different reference frames,with the similar derivation process,the mass relativity equation of Einstein would be obtained.

  6. A Study on the Effects of Compression Ratio, Engine Speed and Equivalence Ratio on HCCI Combustion of DME

    DEFF Research Database (Denmark)

    Pedersen, Troels Dyhr; Schramm, Jesper

    2007-01-01

    An experimental study has been carried out on the homogeneous charge compression ignition (HCCI) combustion of Dimethyl Ether (DME). The study was performed as a parameter variation of engine speed and compression ratio on excess air ratios of approximately 2.5, 3 and 4. The compression ratio...... was adjusted in steps to find suitable regions of operation, and the effect of engine speed was studied at 1000, 2000 and 3000 RPM. It was found that leaner excess air ratios require higher compression ratios to achieve satisfactory combustion. Engine speed also affects operation significantly....

  7. Ion and solvent diffusion and ion conduction of PC-DEC and PC-DME binary solvent electrolytes of LiN(SO2CF3)2

    International Nuclear Information System (INIS)

    Hayamizu, Kikuko; Aihara, Yuichi

    2004-01-01

    Two binary mixed solvent systems typically used for lithium batteries were studied by measuring the self-diffusion coefficients of the solvent, lithium ion and anion, independently by using the multi-nuclear pulsed field-gradient spin-echo (PGSE) 1 H, 7 Li and 19 F NMR method. One system was propylene carbonate (PC) and diethyl carbonate (DEC) system and the other binary system was PC and 1,2-dimethoxyethane (DME), and the lithium salt used was LiN(SO 2 CF 3 ) 2 (LiTFSI). The relative ratio of the PC was changed from zero (pure DME and DEC) to 100% (pure PC) in the DME-PC and the DEC-PC systems, respectively. The self-diffusion coefficients of the solvents were measured with and without the lithium salt, and the two solvents had almost the same diffusion coefficient in the DEC-PC system, while DME diffused faster than PC in the DME-PC system. In the electrolytes the solvents diffused the fastest, followed by the anion with the lithium ion diffusing the slowest. The degree of ion dissociation was estimated for each electrolyte by comparing the ionic conductivities estimated from the ion diffusion and those measured directly by the electrochemical method

  8. Controlling the heat release in HCCI combustion of DME with methanol and EGR

    DEFF Research Database (Denmark)

    Pedersen, Troels Dyhr; Schramm, Jesper; Yanai, Tadanori

    2010-01-01

    quantity required was determined. The added methanol increased the BMEP by increasing the total heat release and retarding the combustion to after TDC. Engine knock was reduced with increasing quantities of methanol. The highest BMEP was achieved when the equivalence ratio of methanol was around 0.......12 at 1000 RPM, and around 0.76 at 1800 RPM. EGR was also used to retarding the timing. With a moderate amount of EGR the effect on the combustion was not notable, but as the equivalence ratio approached unity the combustion was increasingly delayed and the rate of reaction reduced. Engine knock seized...

  9. Quantity Stickiness versus Stackelberg Leadership

    International Nuclear Information System (INIS)

    Ferreira, F. A.

    2008-01-01

    We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

  10. Thermal quantities of 46Ti

    International Nuclear Information System (INIS)

    Rahmatinejad, A.; Razavi, R.; Kakavand, T.

    2015-01-01

    Thermodynamic quantities of 46 Ti have been calculated in the framework of the BCS model with inclusion of modified nuclear pairing gap (MPBCS) that was proposed in our previous publication. Using modified paring gap results in an S-shaped heat capacity curve at critical temperature with a smooth behavior instead of singular behavior of the same curve in the BCS calculations. In addition the thermal quantities have been extracted within the framework of a canonical ensemble according to the new experimental data on nuclear level densities measured by the Oslo group. Comparison shows a good agreement between our calculations in MPBCS and the extracted quantities in the canonical ensemble framework

  11. Challenges in the Greener Production of Formates/Formic Acid, Methanol, and DME by Heterogeneously Catalyzed CO2 Hydrogenation Processes

    KAUST Repository

    Álvarez, Andrea

    2017-06-28

    The recent advances in the development of heterogeneous catalysts and processes for the direct hydrogenation of CO2 to formate/formic acid, methanol, and dimethyl ether are thoroughly reviewed, with special emphasis on thermodynamics and catalyst design considerations. After introducing the main motivation for the development of such processes, we first summarize the most important aspects of CO2 capture and green routes to produce H2. Once the scene in terms of feedstocks is introduced, we carefully summarize the state of the art in the development of heterogeneous catalysts for these important hydrogenation reactions. Finally, in an attempt to give an order of magnitude regarding CO2 valorization, we critically assess economical aspects of the production of methanol and DME and outline future research and development directions.

  12. Polarographic study of Cd(II)-Schiff base complexes and d.m.e. menthanol-water medium

    International Nuclear Information System (INIS)

    Patel, M.S.; Trivedi, T.; Vyas, D.N.

    1978-01-01

    Three Schiff base complexes of Cd 2+ have been investigated polarographically in 60% menthanol-water medium at 26 0 C. The Schiff bases used are salicyladehyde tris buffer (ST), benzaldehydetris buffer (BT) and vanillin tris buffer (VT). Cd-ST and Cd-VT complexes produce reversible reduction wave at dme, while Cd-BT gives a quasi reversible wave. Stability constants of the complexes have been determined and the standard overall electrode reaction rate constant (ksub(e)sup(o)) B of the Cd-BT complex is determined by three different methods. The log β values of complexes are : Cd-ST, 2.72; Cd-VT, 4.90; and Cd-BT, 4.41. (author)

  13. Low-Temperature Oxidation of H2/CH4/C2H6/Ethanol/DME: Experiments and Modelling at High Pressures

    DEFF Research Database (Denmark)

    Hashemi, Hamid; Christensen, Jakob M.; Glarborg, Peter

    2015-01-01

    The main aim of this work was to measure the oxidation characteristics of H2, CH4, C2H6, DME,and ethanol at high pressures (20—100 bar) and low to intermediate temperatures (450—900K) in a laminar flow reactor. Furthermore, a detailed chemical kinetic model was sought to address the oxidation of ...

  14. A Life Cycle Analysis on a Bio-DME production system considering the species of biomass feedstock in Japan and Papua New Guinea

    International Nuclear Information System (INIS)

    Higo, Masashi; Dowaki, Kiyoshi

    2010-01-01

    This paper describes the performance and/or CO 2 intensities of a Bio-DME (Biomass Di-methyl Ether) production system, considering the differences of biomass feedstock. In the past LCA studies on an energy chain model, there is little knowledge on the differences of biomass feedstock and/or available condition. Thus, in this paper, we selected Papua New Guinea (PNG) which has good potential for supply of an energy crop (a short rotation forestry), and Japan where wood remnants are available, as model areas. Also, we referred to 9 species of biomass feedstock of PNG, and to 8 species in Japan. The system boundary on our LCA consists of (1) the pre-treatment process, (2) the energy conversion process, and (3) the fuel transportation process. Especially, since the pre-treatment process has uncertainties related to the moisture content of biomass feedstock, as well as the distance from the cultivation site to the energy plant, we considered them by the Monte Carlo simulation. Next, we executed the process design of the Bio-DME production system based on the basic experimental results of pyrolysis and char gasification reactions. Due to these experiments, the gas components of pyrolysis and the gasification rate under H 2 O (steam) and CO 2 were obtained. Also, we designed the pressurized fluid-bed gasification process. In a liquefaction process, that is, a synthesis process of DME, the result based on an equilibrium constant was used. In the proposed system, a steam turbine for an auxiliary power was assumed to be equipped, too. The energy efficiencies are 39.0-56.8 LHV-%, depending upon the biomass species. Consequently, CO 2 intensities in the whole system were 16.3-47.2 g-CO 2 /MJ-DME in the Japan case, and 12.2-36.7 g-CO 2 /MJ-DME in the PNG one, respectively. Finally, using the results of CO 2 intensities and energy efficiencies, we obtained the regression equations as parameters of hydrogen content and heating value of a feedstock. These equations will be

  15. Quantity Estimation Of The Interactions

    International Nuclear Information System (INIS)

    Gorana, Agim; Malkaj, Partizan; Muda, Valbona

    2007-01-01

    In this paper we present some considerations about quantity estimations, regarding the range of interaction and the conservations laws in various types of interactions. Our estimations are done under classical and quantum point of view and have to do with the interaction's carriers, the radius, the influence range and the intensity of interactions

  16. Recognizing Prefixes in Scientific Quantities

    Science.gov (United States)

    Sokolowski, Andrzej

    2015-01-01

    Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

  17. Definitions of Quantities and Units.

    Science.gov (United States)

    Spurgin, C. B.

    1983-01-01

    Compares various methods of defining derived quantities, arguing for a definitional formula using base or fundamental units in a word equation, or symbol-equations with the symbols explained. Suggests that fundamental units be defined operationally or left regarded as intuitive as in the case of length and time. (JM)

  18. Synthesis of DME by CO2 hydrogenation over La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts

    Directory of Open Access Journals (Sweden)

    Zhang Yajing

    2017-01-01

    Full Text Available A series of La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts were prepared by an oxalate co-precipitation method. The catalysts were fully characterized by X-ray diffraction (XRD, N2 adsorption-desorption, hydrogen temperature pro-grammed reduction (H2-TPR, ammonia temperature programmed desorption (NH3-TPD, and X-ray photoelectron spectroscopy (XPS techniques. The effect of the La2O3 content on the structure and performance of the catalysts was thoroughly investigated. The catalysts were evaluated for the direct synthesis of dimethyl ether (DME from CO2 hydrogenation. The results displayed that La2O3 addition enhanced catalytic performance, and the maximal CO2 conversion (34.3% and DME selectivity (57.3% were obtained over the catalyst with 1% La2O3, which due to the smaller size of Cu species and a larger ratio of Cu+/Cu.

  19. Conceptual design of a hydrogen production system by DME steam reforming and high-efficiency nuclear reactor technology

    International Nuclear Information System (INIS)

    Fukushima, Kimichika; Ogawa, Takashi

    2003-01-01

    Hydrogen is a potential alternative energy source and produced commercially by methane (natural gas) or LPG steam reforming, a process that requires high temperatures, which are produced by burning fossil fuels. However, since this process emits large amounts of CO 2 , replacement of the combustion heat source with a nuclear heat source for 773-1173 K processes has been proposed in order to eliminate these CO 2 emissions. This paper proposes a novel method of low-temperature nuclear hydrogen production by reforming dimethyl ether (DME) with steam produced by a low-temperature nuclear reactor at about 573 K. The authors identified conditions that provide high hydrogen production fraction at low pressure and temperatures of about 523-573 K. By setting this low-temperature hydrogen production process at about 573K upstream from a turbine, it was found theoretically that the total energy utilization efficiency is about 50% and very high. By setting a turbine upstream of the hydrogen production plant, an overall efficiency of is 75% for an FBR and 76% for a supercritical-water cooled power reactor (SCPR). (author)

  20. DOE approach to threshold quantities

    International Nuclear Information System (INIS)

    Wickham, L.E.; Kluk, A.F.; Department of Energy, Washington, DC)

    1985-01-01

    The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Ideally, the threshold must be set high enough to significantly reduce the amount of waste requiring special handling. It must also be low enough so that waste at the threshold quantity poses a very small health risk and multiple exposures to such waste would still constitute a small health risk. It should also be practical to segregate waste above or below the threshold quantity using available instrumentation. Guidance is being prepared to aid DOE sites in establishing threshold quantity values based on pathways analysis using site-specific parameters (waste stream characteristics, maximum exposed individual, population considerations, and site specific parameters such as rainfall, etc.). A guidance dose of between 0.001 to 1.0 mSv/y (0.1 to 100 mrem/y) was recommended with 0.3 mSv/y (30 mrem/y) selected as the guidance dose upon which to base calculations. Several tasks were identified, beginning with the selection of a suitable pathway model for relating dose to the concentration of radioactivity in the waste. Threshold concentrations corresponding to the guidance dose were determined for waste disposal sites at a selected humid and arid site. Finally, cost-benefit considerations at the example sites were addressed. The results of the various tasks are summarized and the relationship of this effort with related developments at other agencies discussed

  1. Quantities used in radiological protection

    International Nuclear Information System (INIS)

    Menossi, Carlos

    2010-01-01

    The application of ICRP recommendations requires knowledge of a variety of concepts and magnitudes. Many of them are employed in other fields of science and precision in its definition reflects this wide application. In this regard, information on quantities and basic units of radiation, which exists in numerous publications, are subjects of great interest. The characteristics and radiation effects are studied by physicists, biologists and chemists mainly. However, there are basics that must be known and to be recognized by general practitioners and specialists from all branches of medicine. The information on quantities and units are used only in radiation protection, have been obtained from the reports listed on the attached bibliography. Such quantities and units contain weighting factors used to provide for different types of radiation and energies that affect the body and thus take into account the relative radio-sensitivity of different tissues. Additionally, they have added a series of data for a better understanding of the units: for example, multiples and sub-multiples, and some examples of converting the units used in radiation protection. (author) [es

  2. Rainwater in Egypt: quantity, distribution and harvesting

    Directory of Open Access Journals (Sweden)

    H.I. ABDEL-SHAFY

    2010-11-01

    Full Text Available Egypt has limited water resources, and it will be under water stress within the year 2030. Therefore, Egypt should consider the natural and non-conventional water resources to overcome such problem. Rain harvesting is one solution; but not all; particularly on the north coast by the Mediterranean Sea and the Red sea. In this paper, the rainwater issue is reviewed and discussed in terms of the quantities and distribution at different selected areas in Egypt. The amount of rain falls at different location in Egypt was collected for a period of 16 months. The data indicated that rainfall in Egypt is very scarce, with an annual average of 12 mm and ranges from 0 mm/year in the desert to 200 mm/year in the north coastal region. The maximum total amount of rain does not exceed 1.8 billion m3per year. However, the average annual amount of rainfall water that is effectively utilized for agriculture purposes is estimated to be 1 billion m3. Harvesting pilot plant was constructed and implemented in Alexandria directly on the Mediterranean Sea. The harvested rain was used for irrigation and treated for drinking. It was, therefore, recommended to develop sustainable catchments at appropriate locations in the rain-fed areas at the north coast as well as cost effective grafting of the indigenous technologies with the innovative techniques.

  3. Modification of piston bowl geometry and injection strategy, and investigation of EGR composition for a DME-burning direct injection engine

    Directory of Open Access Journals (Sweden)

    Kianoosh Shojae

    2017-01-01

    Full Text Available The amount of pollutant gases in the atmosphere has reached a critical state due to an increase in industrial development and the rapid growth of automobile industries that use fossil fuels. The combustion of fossil fuels produces harmful gases such as carbon dioxide, nitrogen monoxide (NO, soot, particulate matter (PM, etc. The use of Dimethyl Ether (DME biofuel in diesel engines or other combustion processes have been highly regarded by researchers. Studies show that the use of pure DME in automotive engines will be possible in the near future. The present work evaluated the environmental and performance effects of changing the injection strategy (time and temperature, piston bowl geometry, and exhaust gas recirculation (EGR composition for a DME-burning engine. The modification of piston bowl parameters and engine simulation were numerically performed by using AVL fire CFD code. For model validation, the calculated mean pressure and rate of heat released (RHR were compared to the experimental data and the results showed a good agreement (under a 70% load and 1200-rpm engine speed. It was found that retarding injection timing (reduction in in-cylinder temperature, consequently caused a reduction in NO emissions and increased soot formation, reciprocally; this occurred because of a reduction in temperature and a lower soot oxidation in the combustion chamber. It became clear that 3 deg before top dead center (BTDC was the appropriate injection timing for the DME-burning heavy duty diesel engine running under 1200 rpm. Also, the parametrical modification of the piston bowl geometry and the simultaneous decrease of Tm (piston bowl depth and R3 (bowl inner radius lengths were associated with lower exhaust NO emissions. For the perfect utilization of DME fuel in an HD diesel engine, the suggested proper lengths of Tm and R3 were 0.008 and 0.0079 m, respectively. Furthermore, various EGR compositions for the reduction of exhaust NO were investigated

  4. How necessary are the new quantities

    International Nuclear Information System (INIS)

    Kraus, W.

    1991-01-01

    The necessity of the ICRU operational quantities is discussed from the point of view of practical, opertional radiation protection, on the basis of ICRU report 43. It is clear that, although the new quantities have some advantages over previous systems of operational quantities, there are some disadvantages as well. The decision to adopt these quantities is, therefore, not clear cut. (orig.)

  5. Are necessary unmeasurable quantities in radiation protection?

    International Nuclear Information System (INIS)

    David, M.G.; Correa, M.F.; Videira, A.A.P.

    2016-01-01

    We discuss in this paper the metrological status of unmeasurable protection quantities and the need to maintain these kind of quantities in the system. The discussion is based on reports from the institutions responsible for the quantities and on scientific publications. In conclusion, we can say that there are alternatives for changing the system in a way that it keep just measurable quantities, nevertheless the present system is well assimilated. Even though a proposal yet to be presented for changing the system, although might simplify and improve it, is not intended to overcome the existence of unmeasurable quantities or the two kinds of quantities. (author)

  6. Reductions in greenhouse gas emissions and oil use by DME (di-methyl ether) and FT (Fischer-Tropsch) diesel production in chemical pulp mills

    International Nuclear Information System (INIS)

    Joelsson, Jonas M.; Gustavsson, Leif

    2012-01-01

    Using energy systems analysis, we examine the potential to reduce CO 2 emissions and oil use by integrating motor biofuel production with pulp mills. BLG-DME (black liquor gasification with di-methyl ether production) is compared with solid biomass gasification with BIG-FT (solid biomass gasification with Fischer-Tropsch fuel production). The studied systems are expanded with stand-alone production of biomass-based electricity and motor fuel so that they yield the same functional unit in terms of motor fuel and electricity as well as pulp or paper product, in order to facilitate comparison. More motor biofuel can be produced in integration with the studied mills with BLG-DME than with BIG-FT because the black liquor flow is large compared with other fuel streams in the mill and the integration potential for BIG-FT is limited by the mill’s heat demand. When both systems are required to produce the same functional unit, the BLG-DME system achieves higher system efficiency and larger reductions in CO 2 emissions and oil use per unit of biomass consumed. In general, integration of motor biofuel production with a pulp mill is more efficient than stand-alone motor biofuel production. Larger reductions in CO 2 emissions or oil use can, however, be achieved if biomass replaces coal or oil in stationary applications. -- Highlights: ► CO 2 emission and oil use reductions quantified for pulp mill-based biorefineries. ► Black liquor gasification gives larger reductions than solid biomass gasification. ► Lower mill steam demand increases the black liquor gasification advantage. ► Biomass directly replacing coal or oil in stationary plants gives larger reductions.

  7. Reductions in greenhouse gas emissions and oil use by DME (di-methyl ether) and FT (Fischer-Tropsch) diesel production in chemical pulp mills

    Energy Technology Data Exchange (ETDEWEB)

    Joelsson, Jonas M., E-mail: joelsson.jonas@hotmail.com [Ecotechnology and Environmental Science, Mid Sweden University, SE-831 25 Oestersund (Sweden); Gustavsson, Leif [Linnaeus University, SE- 351 95 Vaexjoe (Sweden)

    2012-03-15

    Using energy systems analysis, we examine the potential to reduce CO{sub 2} emissions and oil use by integrating motor biofuel production with pulp mills. BLG-DME (black liquor gasification with di-methyl ether production) is compared with solid biomass gasification with BIG-FT (solid biomass gasification with Fischer-Tropsch fuel production). The studied systems are expanded with stand-alone production of biomass-based electricity and motor fuel so that they yield the same functional unit in terms of motor fuel and electricity as well as pulp or paper product, in order to facilitate comparison. More motor biofuel can be produced in integration with the studied mills with BLG-DME than with BIG-FT because the black liquor flow is large compared with other fuel streams in the mill and the integration potential for BIG-FT is limited by the mill's heat demand. When both systems are required to produce the same functional unit, the BLG-DME system achieves higher system efficiency and larger reductions in CO{sub 2} emissions and oil use per unit of biomass consumed. In general, integration of motor biofuel production with a pulp mill is more efficient than stand-alone motor biofuel production. Larger reductions in CO{sub 2} emissions or oil use can, however, be achieved if biomass replaces coal or oil in stationary applications. -- Highlights: Black-Right-Pointing-Pointer CO{sub 2} emission and oil use reductions quantified for pulp mill-based biorefineries. Black-Right-Pointing-Pointer Black liquor gasification gives larger reductions than solid biomass gasification. Black-Right-Pointing-Pointer Lower mill steam demand increases the black liquor gasification advantage. Black-Right-Pointing-Pointer Biomass directly replacing coal or oil in stationary plants gives larger reductions.

  8. Asymptotic conditions and conserved quantities

    International Nuclear Information System (INIS)

    Koul, R.K.

    1990-01-01

    Two problems have been investigated in this dissertation. The first one deals with the relationship between stationary space-times which are flat at null infinity and stationary space-times which are asymptotic flat at space-like infinity. It is shown that the stationary space-times which are asymptotically flat, in the Penrose sense, at null infinity, are asymptotically flat at space-like infinity in the Geroch sense and metric at space like infinity is at least C 1 . In the converse it is shown that the stationary space-times which are asymptotically flat at space like infinity, in the Beig sense, are asymptotically flat at null infinity in the Penrose sense. The second problem addressed deals with the theories of arbitrary dimensions. The theories treated are the ones which have fiber bundle structure, outside some compact region. For these theories the criterion for the choice of the background metric is specified, and the boundary condition for the initial data set (q ab , P ab ) is given in terms of the background metric. Having these boundary conditions it is shown that the symplectic structure and the constraint functionals are well defined. The conserved quantities associated with internal Killing vector fields are specified. Lastly the energy relative to a fixed background and the total energy of the theory have been given. It is also shown that the total energy of the theory is independent of the choice of the background

  9. TIME-RESOLVED PROPERTIES AND GLOBAL TRENDS IN dMe FLARES FROM SIMULTANEOUS PHOTOMETRY AND SPECTRA

    Energy Technology Data Exchange (ETDEWEB)

    Kowalski, Adam F.; Hawley, Suzanne L.; Davenport, James R. A. [Astronomy Department, University of Washington, Box 351580, U.W. Seattle, WA 98195-1580 (United States); Wisniewski, John P. [HL Dodge Department of Physics and Astronomy, University of Oklahoma, 440 W Brooks Street, Norman, OK 73019 (United States); Osten, Rachel A. [Space Telescope Science Institute, 3700 San Martin Drive Baltimore, MD 21218 (United States); Hilton, Eric J. [Universe Sandbox, Seattle, WA (United States); Holtzman, Jon A. [Department of Astronomy, New Mexico State University, Box 30001, Las Cruces, NM 88003 (United States); Schmidt, Sarah J., E-mail: adam.f.kowalski@nasa.gov [Department of Astronomy, Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States)

    2013-07-15

    red in both the impulsive and gradual decay phases of all 20 flares. This discrepancy implies that further work is needed to understand the heating at high column mass during dMe flares.

  10. TIME-RESOLVED PROPERTIES AND GLOBAL TRENDS IN dMe FLARES FROM SIMULTANEOUS PHOTOMETRY AND SPECTRA

    International Nuclear Information System (INIS)

    Kowalski, Adam F.; Hawley, Suzanne L.; Davenport, James R. A.; Wisniewski, John P.; Osten, Rachel A.; Hilton, Eric J.; Holtzman, Jon A.; Schmidt, Sarah J.

    2013-01-01

    gradual decay phases of all 20 flares. This discrepancy implies that further work is needed to understand the heating at high column mass during dMe flares

  11. Dose rate constants for new dose quantities

    International Nuclear Information System (INIS)

    Tschurlovits, M.; Daverda, G.; Leitner, A.

    1992-01-01

    Conceptual changes and new quantities made is necessary to reassess dose rate quantities. Calculations of the dose rate constant were done for air kerma, ambient dose equivalent and directional dose equivalent. The number of radionuclides is more than 200. The threshold energy is selected as 20 keV for the dose equivalent constants. The dose rate constant for the photon equivalent dose as used mainly in German speaking countries as a temporary quantity is also included. (Author)

  12. The new operational quantities for radiation protection

    International Nuclear Information System (INIS)

    Kellerer, A.M.

    1985-01-01

    Philosophies and quantities for radiation protection have often been subjected to changes, and some of the developments are traced which ultimately led to recent proposals by ICRU. Development in the past has largely been towards clarification and generalisation of definitions. The present changes, however, reflect a more fundamental issue, the transition from the limitation system to the assessment system in radiation protection. The index quantities were suitable tools to ascertain compliance with the limitation system of radiation protection. The new quantities proposed by ICRU are suitable estimators for effective dose equivalent, which is an essential quantity in the assessment system of radiation protection. A synopsis of the definitions is given. (author)

  13. Pilot Implementations

    DEFF Research Database (Denmark)

    Manikas, Maria Ie

    by conducting a literature review. The concept of pilot implementation, although commonly used in practice, is rather disregarded in research. In the literature, pilot implementations are mainly treated as secondary to the learning outcomes and are presented as merely a means to acquire knowledge about a given...... objective. The prevalent understanding is that pilot implementations are an ISD technique that extends prototyping from the lab and into test during real use. Another perception is that pilot implementations are a project multiple of co-existing enactments of the pilot implementation. From this perspective......This PhD dissertation engages in the study of pilot (system) implementation. In the field of information systems, pilot implementations are commissioned as a way to learn from real use of a pilot system with real data, by real users during an information systems development (ISD) project and before...

  14. Continuing Professional Development in the quantity surveying ...

    African Journals Online (AJOL)

    This research study was conducted in order to investigate Continuing Professional Development (CPD) in the South African quantity surveying profession. The study further aimed to establish the reasons why some quantity surveyors do not acquire the required CPD hours and face losing their professional registration with ...

  15. Continuing Professional Development in the quantity surveying ...

    African Journals Online (AJOL)

    1991-01-01

    Jan 1, 1991 ... The research established that quantity surveyors regarded handing in their CPD ... Surveying, Walter Sisulu University, PO Box 1421, East London, 5200, South Africa. ... Keywords: Continuing professional development, quantity surveying, perception .... In spite of this opportunity enshrined in the Act, the.

  16. 36 CFR 223.220 - Quantity determination.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

  17. 30 CFR 75.325 - Air quantity.

    Science.gov (United States)

    2010-07-01

    ... the exposure of miners. (i) A ventilating air quantity that is less than what is required by paragraph... results of sampling that demonstrate that the lesser air quantity will maintain continuous compliance with applicable TLV ®'s. (j) If during sampling required by § 70.1900(c) of this subchapter the ventilating air is...

  18. Method and means for determining heat quantities

    Energy Technology Data Exchange (ETDEWEB)

    Waasdorp, G G; de Jong, J J; Bijl, A

    1965-08-24

    To determine the quantity of potential heat W that has flowed past a certain point in a certain time, the velocity of the combustible Q, the temperature T, and the specific gravity YDTU are measured, and these values are transmitted to a computer which automatically calculates the quantity: ..pi..EQUATION/sup -/ in which delta T is the difference between the combustible temperature T and a reference temperature, and in which the relation f(YDTU, delta T) represents the heat of combustion as a function of the quantities YDTU and delta T and possibly other properties of the combustible. Alternatively the quantity: ..pi..EQUATION/sup -/ may be measured; here the quantities have the same meaning as above.

  19. Effect of irradiation power and time on ultrasound assisted co-precipitation of nanostructured CuO–ZnO–Al2O3 over HZSM-5 used for direct conversion of syngas to DME as a green fuel

    International Nuclear Information System (INIS)

    Allahyari, Somaiyeh; Haghighi, Mohammad; Ebadi, Amanollah; Hosseinzadeh, Shahin

    2014-01-01

    Graphical abstract: Nanostructured CuO–ZnO–Al 2 O 3 /HZSM-5 catalyst has been prepared by an ultrasound-assisted co-precipitation hybrid method. Effect of power and irradiation time have been studied by changing the time (30–45–60 min) and power of sonication (50–100–150 W) during the synthesis which lead to different physiochemical properties of the catalyst. The XRD, FESEM, EDX, FTIR and BET analyses exhibited smaller particles with higher surface area and less population of particle aggregates at longer and highly irradiated catalysts. Study on the performance of investigated catalysts in direct synthesis of DME from syngas showed ultrasound-assisted co-precipitated synthesized catalysts have superior reactivity and stability compared with non-sonicated catalyst. Among sonicated catalysts, with increasing power and time of irradiation, the catalyst represents higher activity and DME selectivity. - Highlights: • Synthesis of CuO–ZnO–Al 2 O 3 /HZSM-5 by ultrasound assisted co-precipitation method. • Significant changes in morphology and surface area after ultrasound irradiations. • Smaller dispersed particle aggregates in longer and more intense irradiated catalysts. • Improvement in reactivity and stability of the longer and more intense ultrasound irradiated CZAZ catalyst. - Abstract: Nanostructured CuO–ZnO–Al 2 O 3 /HZSM-5 catalyst has been prepared by an ultrasound-assisted co-precipitation hybrid method. The effect of irradiation power and irradiation time have been studied by changing time (30, 45, 60 min) and power of the sonication (50, 100, 150 W) during the synthesis which led to different physiochemical properties of the nanocatalyst. The XRD, FESEM, EDX, FTIR and BET analyses exhibited smaller particles with higher surface area and less population of particle aggregates at longer and highly irradiated nanocatalysts. The nanocatalyst irradiated at 150 W for 60 min (the longest irradiation time and the most intense power

  20. A Viewpoint on the Quantity "Plane Angle"

    Science.gov (United States)

    Eder, W. E.

    1982-01-01

    Properties of the quantity "plane angle" are explored under the hypothesis that it is a dimensional quantity. The exploration proceeds especially with respect to the physical concept, its mathematical treatment, vector concepts, measurement theory, units of related quantities, engineering pragmatism, and SI. An attempt is made to bring these different relations into a rational, logical and consistent framework, and thus to justify the hypothesis. Various types of vectorial quantities are recognized, and their properties described with an outline of the necessary algebraic manipulations. The concept of plane angle is amplified, and its interdependence with the circular arc is explored. The resulting units of plane angle form a class of similar scales of measurement. Consequences of the confirmed hypothesis are developed for mathematical expressions involving trigonometric functions, rotational volumes and areas, mathematical limits, differentiation and series expansion. Consequences for mechanical rotational quantities are developed, with proposals for revisions to a number of expressions for derived units within SI. A revised definition for the quantity "plane angle" is stated to take account of the developed insights. There is a clear need to reconsider the status of plane angle and some other quantities within the international framework of SI.

  1. Ultrasound assisted co-precipitation of nanostructured CuO-ZnO-Al2O3 over HZSM-5: effect of precursor and irradiation power on nanocatalyst properties and catalytic performance for direct syngas to DME.

    Science.gov (United States)

    Allahyari, Somaiyeh; Haghighi, Mohammad; Ebadi, Amanollah; Hosseinzadeh, Shahin

    2014-03-01

    Nanostructured CuO-ZnO-Al2O3/HZSM-5 was synthesized from nitrate and acetate precursors using ultrasound assisted co-precipitation method under different irradiation powers. The CuO-ZnO-Al2O3/HZSM-5 nanocatalysts were characterized using XRD, FESEM, BET, FTIR and EDX Dot-mapping analyses. The results indicated precursor type and irradiation power have significant influences on phase structure, morphology, surface area and functional groups. It was observed that the acetate formulated CuO-ZnO-Al2O3/HZSM-5 nanocatalyst have smaller CuO crystals with better dispersion and stronger interaction between components in comparison to nitrate based nanocatalysts. Ultrasound assisted co-precipitation synthesis method resulted in nanocatalyst with more uniform morphology compared to conventional method and increasing irradiation power yields smaller particles with better dispersion and higher surface area. Additionally the crystallinity of CuO is lower at high irradiation powers leading to stronger interaction between metal oxides. The nanocatalysts performance were tested at 200-300 °C, 10-40 bar and space velocity of 18,000-36,000 cm(3)/g h with the inlet gas composition of H2/CO = 2/1 in a stainless steel autoclave reactor. The acetate based nanocatalysts irradiated with higher levels of power exhibited better reactivity in terms of CO conversion and DME yield. While there is an optimal temperature for CO conversion and DME yield in direct synthesis of DME, CO conversion and DME yield both increase with the pressure increase. Furthermore ultrasound assisted co-precipitation method yields more stable CuO-ZnO-Al2O3/HZSM-5 nanocatalyst while conventional precipitated nanocatalyst lost their activity ca. 18% and 58% in terms of CO conversion and DME yield respectively in 24 h time on stream test.

  2. Workplace stress experienced by quantity surveyors

    African Journals Online (AJOL)

    Paul (P.A.) Bowen, Department of Construction Economics and Management,. University of Cape Town, Private ..... Explore workplace stress levels among quantity surveyors in the developing nation of ...... London: Free. Association Books.

  3. The Radiometric Measurement Quantity for SAR Images

    OpenAIRE

    Döring, Björn J.; Schwerdt, Marco

    2013-01-01

    A Synthetic Aperture Radar (SAR) system measures among other quantities the terrain radar reflectivity. After image calibration, the pixel intensities are commonly expressed in terms of radar cross sections (for point targets) or as backscatter coefficients (for distributed targets), which are directly related. This paper argues that pixel intensities are not generally proportional to radar cross section or derived physical quantities. The paper further proposes to replace the inaccurate term...

  4. Average Transverse Momentum Quantities Approaching the Lightfront

    OpenAIRE

    Boer, Daniel

    2015-01-01

    In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...

  5. A conserved quantity in thin body dynamics

    Science.gov (United States)

    Hanna, J. A.; Pendar, H.

    2016-02-01

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

  6. Critical review of the current radiation protection quantities and units

    International Nuclear Information System (INIS)

    Sabol, J.

    1998-01-01

    Examples exist in dosimetry and radiation protection where primary attention was focused on the unit rather than the corresponding quantity. Another difficulty arises from the fact that quantities in this field cannot be considered as pure physical quantities, they are rather biophysical quantities. There are too many quantities (e. g. 17 quantities based on the dose equivalent), with differences in numerical values of 'similar' quantities, not always satisfactory approximations of virtually unmeasurable quantities by measurable quantities, inconsistency in definitions and interpretations of quantities of some international expert bodies, and problems of weighting and conversion factors. (M.D.)

  7. Pilot implementation

    DEFF Research Database (Denmark)

    Hertzum, Morten; Bansler, Jørgen P.; Havn, Erling C.

    2012-01-01

    A recurrent problem in information-systems development (ISD) is that many design shortcomings are not detected during development, but first after the system has been delivered and implemented in its intended environment. Pilot implementations appear to promise a way to extend prototyping from...... the laboratory to the field, thereby allowing users to experience a system design under realistic conditions and developers to get feedback from realistic use while the design is still malleable. We characterize pilot implementation, contrast it with prototyping, propose a iveelement model of pilot...... implementation and provide three empirical illustrations of our model. We conclude that pilot implementation has much merit as an ISD technique when system performance is contingent on context. But we also warn developers that, despite their seductive conceptual simplicity, pilot implementations can be difficult...

  8. Management of small quantities of radioactive waste

    International Nuclear Information System (INIS)

    1998-09-01

    The main objective of this publication is to provide practical guidance primarily to developing Member States on the predisposal management of small quantities of radioactive waste arising from hospitals, laboratories, industries, institutions, research reactors and research centres.The publication covers the management of liquid, solid and gaseous radioactive wastes at the users' premises and gives general guidance on procedures at a centralized waste management facility. Predisposal management of radioactive waste includes handling, treatment, conditioning, storage and transportation. This publication provides information and guidance on the following topics: national waste management framework; origin and characteristics of radioactive waste arising from users generating small quantities of waste; radioactive waste management concepts appropriate for small quantities; local waste management; the documentation and approval necessary for the consignment of waste to a centralized waste management facility; centralized waste management; exemption of radionuclides from the regulatory body; transportation; environmental monitoring; quality assurance for the whole predisposal process; regional co-operation aspects

  9. A conserved quantity in thin body dynamics

    International Nuclear Information System (INIS)

    Hanna, J.A.; Pendar, H.

    2016-01-01

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

  10. A conserved quantity in thin body dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Hanna, J.A., E-mail: hannaj@vt.edu [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Department of Physics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Pendar, H. [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States)

    2016-02-15

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

  11. An investigation of the effects of spray angle and injection strategy on dimethyl ether (DME) combustion and exhaust emission characteristics in a common-rail diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Seung Hyun; Cha, June Pyo [Graduate School of Hanyang University, Hanyang University, 17 Haengdang-dong, Sungdong-gu, Seoul, 133-791 (Korea); Lee, Chang Sik [Department of Mechanical Engineering, Hanyang University, 17 Haengdang-dong, Sungdong-gu, Seoul 133-791 (Korea)

    2010-11-15

    An experimental investigation was performed on the effects of spray angle and injection strategies (single and multiple) on the combustion characteristics, concentrations of exhaust emissions, and the particle size distribution in a direct-injection (DI) compression ignition engine fueled with dimethyl ether (DME) fuel. In this study, two types of narrow spray angle injectors ({theta}{sub spray} = 70 and 60 ) were examined and its results were compared with the results of conventional spray angle ({theta}{sub spray} = 156 ). In addition, to investigate the optimal operating conditions, early single-injection and multiple-injection strategies were employed to reduce cylinder wall-wetting of the injected fuels and to promote the ignition of premixed charge. The engine test was performed at 1400 rpm, and the injection timings were varied from TDC to BTDC 40 of the crank angle. The experimental results showed that the combustion pressure from single combustion for narrow-angle injectors ({theta}{sub spray} = 70 and 60 ) is increased, as compared to the results of the wide-angle injector ({theta}{sub spray} = 156 ) with advanced injection timing of BTDC 35 . In addition, two peaks of the rate of heat release (ROHR) are generated by the combustion of air-fuel premixed mixtures. DME combustion for all test injectors indicated low levels of soot emissions at all injection timings. The NO{sub x} emissions for narrow-angle injectors simultaneously increased in proportion to the advance in injection timing up to BTDC 25 , whereas BTDC 20 for the wide-angle injector. For multiple injections, the combustion pressure and ROHR of the first injection with narrow-angle injectors are combusted more actively, and the ignition delay of the second injected fuel is shorter than with the wide-angle injector. However, the second combustion pressure and ROHR were lower than during the first injection, and combustion durations are prolonged, as compared to the wide-angle injector. With

  12. An investigation of the effects of spray angle and injection strategy on dimethyl ether (DME) combustion and exhaust emission characteristics in a common-rail diesel engine

    International Nuclear Information System (INIS)

    Yoon, Seung Hyun; Cha, June Pyo; Lee, Chang Sik

    2010-01-01

    An experimental investigation was performed on the effects of spray angle and injection strategies (single and multiple) on the combustion characteristics, concentrations of exhaust emissions, and the particle size distribution in a direct-injection (DI) compression ignition engine fueled with dimethyl ether (DME) fuel. In this study, two types of narrow spray angle injectors (θ spray = 70 and 60 ) were examined and its results were compared with the results of conventional spray angle (θ spray = 156 ). In addition, to investigate the optimal operating conditions, early single-injection and multiple-injection strategies were employed to reduce cylinder wall-wetting of the injected fuels and to promote the ignition of premixed charge. The engine test was performed at 1400 rpm, and the injection timings were varied from TDC to BTDC 40 of the crank angle. The experimental results showed that the combustion pressure from single combustion for narrow-angle injectors (θ spray = 70 and 60 ) is increased, as compared to the results of the wide-angle injector (θ spray = 156 ) with advanced injection timing of BTDC 35 . In addition, two peaks of the rate of heat release (ROHR) are generated by the combustion of air-fuel premixed mixtures. DME combustion for all test injectors indicated low levels of soot emissions at all injection timings. The NO x emissions for narrow-angle injectors simultaneously increased in proportion to the advance in injection timing up to BTDC 25 , whereas BTDC 20 for the wide-angle injector. For multiple injections, the combustion pressure and ROHR of the first injection with narrow-angle injectors are combusted more actively, and the ignition delay of the second injected fuel is shorter than with the wide-angle injector. However, the second combustion pressure and ROHR were lower than during the first injection, and combustion durations are prolonged, as compared to the wide-angle injector. With advanced timing of the first injection, narrow

  13. Relevance of protection quantities in medical exposures

    International Nuclear Information System (INIS)

    Pradhan, A.S.

    2008-01-01

    International Commission on Radiological Protection (ICRP) continues to classify the exposures to radiation in three categories; namely 1- occupational exposure, 2- public exposure, and 3- medical exposure. Protection quantities are primarily meant for the regulatory purpose in radiological protection for controlling and limiting stochastic risks in occupational and public exposures. These are based on two basic assumptions of 1- linear no-threshold dose-effect relationship (LNT) at low doses and 2- long-term additivity of low doses. Medical exposure are predominantly delivered to individuals (patients) undergoing diagnostic examinations, interventional procedures and radiation therapy but also include individual caring for or comforting patients incurring exposure and the volunteers of biomedical medical research programmes. Radiation protection is as relevant to occupational and public exposure as to medical exposures except that the dose limits set for the formers are not applicable to medical exposure but reference levels and dose constrains are recommended for diagnostic and interventional medical procedures. In medical institutions, both the occupational and medical exposure takes place. Since the doses in diagnostic examinations are low, it has been observed that not only the protection quantities are often used in such cases but these are extended to estimate the number of cancer deaths due to such practices. One of the striking features of the new ICRP recommendations has been to elaborate the concepts of the dosimetric quantities. The limitation of protection quantities ((Effective dose, E=Σ RT D TR .W T .W R and Equivalent Dose H T =Σ RT D TR .W R ) have been brought out and this has raised a great concern and initiated debates on the use of these quantities in medical exposures. Consequently, ICRP has set a task group to provide more details and the recommendations. It has, therefore, became important to draw the attention of medical physics community

  14. Editorial: New operational dose equivalent quantities

    International Nuclear Information System (INIS)

    Harvey, J.R.

    1985-01-01

    The ICRU Report 39 entitled ''Determination of Dose Equivalents Resulting from External Radiation Sources'' is briefly discussed. Four new operational dose equivalent quantities have been recommended in ICRU 39. The 'ambient dose equivalent' and the 'directional dose equivalent' are applicable to environmental monitoring and the 'individual dose equivalent, penetrating' and the 'individual dose equivalent, superficial' are applicable to individual monitoring. The quantities should meet the needs of day-to-day operational practice, while being acceptable to those concerned with metrological precision, and at the same time be used to give effective control consistent with current perceptions of the risks associated with exposure to ionizing radiations. (U.K.)

  15. Calibration of personal dosimeters: Quantities and terminology

    International Nuclear Information System (INIS)

    Aleinikov, V.E.

    1999-01-01

    The numerical results obtained in the interpretation of individual monitoring of external radiation depend not only on the accurate calibration of the radiation measurement instruments involved, but also on the definition of the quantities in term of which these instruments are calibrated The absence of uniformity in terminology not only makes it difficult to understand properly the scientific and technical literature but can also lead to incorrect interpretation of particular concepts and recommendations. In this paper, brief consideration is given to definition of radiation quantities and terminology used in calibration procedures. (author)

  16. 7 CFR 35.13 - Minimum quantity.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

  17. Varieties of Quantity Estimation in Children

    Science.gov (United States)

    Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

    2015-01-01

    In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

  18. Symmetries and conserved quantities in geodesic motion

    International Nuclear Information System (INIS)

    Hojman, S.; Nunez, L.; Patino, A.; Rago, H.

    1986-01-01

    Recently obtained results linking several constants of motion to one (non-Noetherian) symmetry to the problem of geodesic motion in Riemannian space-times are applied. The construction of conserved quantities in geodesic motion as well as the deduction of geometrical statements about Riemannian space-times are achieved

  19. Hypergraph topological quantities for tagged social networks

    Science.gov (United States)

    Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

    2009-09-01

    Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

  20. 16 CFR 500.25 - Net quantity, average quantity, permitted variations.

    Science.gov (United States)

    2010-01-01

    ... good distribution practice and which unavoidably result in change of weight or mass or measure. (c... good packaging practice: Provided, that such variations shall not be permitted to such extent that the... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity, average quantity, permitted...

  1. Black Liquor Gasification with Motor Fuel Production - BLGMF II - A techno-economic feasibility study on catalytic Fischer-Tropsch synthesis for synthetic diesel production in comparison with methanol and DME as transport fuels

    Energy Technology Data Exchange (ETDEWEB)

    Ekbom, Tomas; Berglin, Niklas; Loegdberg, Sara [Nykomb Synergetics AB, Stockholm (Sweden)

    2005-06-15

    The present project presents additional results to the former BLGMF project, which investigate Black Liquor Gasification with Motor Fuels (BLGMF) production. The objectives were to investigate, based on the KAM 2 program Ecocyclic Pulp Mill (2,000 ADt/day of pulp) the feasibility of synthetic fuels production. Specifically the route to Fischer-Tropsch diesel fuels is investigated as comparison to earlier work on methanol/DME. As modern kraft pulp mills have a surplus of energy, they could become key suppliers of renewable fuels. It is thus of great interest to convert the spent cooking product 'black liquor' to an energy carrier of high value. The resulting biomass-to-fuel energy efficiency when only biomass is used as an external energy source was 43% for FTD or 65% for FT products compared with 66% for methanol and 67% for DME. The FTD calculation is considerably more complicated and based on assumptions, therefore the uncertainty is higher. Would the diesel be taken out with a T95% of 320 deg C the FTD efficiency would be 45%. FT synthesis also opens up a possibility to produce e.g. lube oils from waxes produced. The total net FT-products output equals 4115 barrels/day. The FTD production cost is calculated as the energy share of the total production cost and assumes an offset of naphtha covering its own costs, where it is essential that it finds a market. Assuming same petrol (methanol) and diesel (DME, FTD) costs for the consumer the payback time were 2.6, 2.9 and 3.4 years with an IRR of 40%, 45% and 30%, respectively. In conclusion, there are necessary resources and potential for large-scale methanol (or DME, FTD) production and substantial economic incentive for making plant investments and achieving competitive product revenues.

  2. Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition (HCCI) Engine Fueled with Hydrogen, Natural Gas, and DME

    Energy Technology Data Exchange (ETDEWEB)

    Pratapas, John; Mather, Daniel; Kozlovsky, Anton

    2013-03-31

    analysis of test results indicates that hydrogen enhanced natural gas HCCI (versus neat natural gas HCCI at comparable stoichiometry) had the following characteristics: • Substantially lower intake temperature needed for stable HCCI combustion • Inconclusive impact on engine BMEP and power produced, • Small reduction in the thermal efficiency of the engine, • Moderate reduction in the unburned hydrocarbons in the exhaust, • Slight increase in NOx emissions in the exhaust, • Slight reduction in CO2 in the exhaust. • Increased knocking at rich stoichiometry The major accomplishments and findings from the project can be summarized as follows: 1. A model was calibrated for accurately predicting heat release rate and peak pressures for HCCI combustion when operating on hydrogen and natural gas blends. 2. A single cylinder research engine was thoroughly mapped to compare performance and emissions for micro-pilot natural gas compression ignition, and HCCI combustion for neat natural gas versus blends of natural gas and hydrogen.

  3. Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition (HCCI) Engine Fueled with Hydrogen, Natural Gas, and DME

    Energy Technology Data Exchange (ETDEWEB)

    John Pratapas; Daniel Mather; Anton Kozlovsky

    2007-03-31

    analysis of test results indicates that hydrogen enhanced natural gas HCCI (versus neat natural gas HCCI at comparable stoichiometry) had the following characteristics: (1) Substantially lower intake temperature needed for stable HCCI combustion; (2) Inconclusive impact on engine BMEP and power produced; (3) Small reduction in the thermal efficiency of the engine; (4) Moderate reduction in the unburned hydrocarbons in the exhaust; (5) Slight increase in NOx emissions in the exhaust; (6) Slight reduction in CO2 in the exhaust; and (7) Increased knocking at rich stoichiometry. The major accomplishments and findings from the project can be summarized as follows: (1) A model was calibrated for accurately predicting heat release rate and peak pressures for HCCI combustion when operating on hydrogen and natural gas blends. (2) A single cylinder research engine was thoroughly mapped to compare performance and emissions for micro-pilot natural gas compression ignition, and HCCI combustion for neat natural gas versus blends of natural gas and hydrogen. (3) The benefits of using hydrogen to extend, up to a limit, the stable operating window for HCCI combustion of natural gas at higher intake pressures, leaner air to fuel ratios or lower inlet temperatures was documented.

  4. Strategic Planning in Irish Quantity Surveying Pracitces

    OpenAIRE

    Murphy, Roisin

    2011-01-01

    The role and usefulness of strategic planning has been well documented over several decades of strategic management research. Despite the significant body of existing knowledge in the field of strategic planning, there remains a paucity of investigation into the construction sector, specifically in Professional Service Firms (PSF’s) operating within it. The aim of this research was to ascertain the type, scope and extent of strategic planning within Irish Quantity Surveying (QS) practices and...

  5. Radiation quantities and units. ICRU report 33

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. It is recommended that energy state be inserted into the definition of activity and that the word transformation be replaced by transition. These modifications have now been incorporated into the current definition. Helpful comments on the previous quantities and units report have resulted in clarification of several points in the present Report. In line with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection I.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. 11 refs., 4 tabs

  6. Quantity discrimination in wolves (Canis lupus

    Directory of Open Access Journals (Sweden)

    Ewelina eUtrata

    2012-11-01

    Full Text Available Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested eleven hand-raised wolves (Canis lupus in a two-way choice task. We placed a number of food items (one to four sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris and coyotes (Canis latrans, our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current setup are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law.

  7. The Acquisition of Quantity Contrasts in Guina-ang Bontok

    Science.gov (United States)

    Aoyama, Katsura; Reid, Lawrence A.

    2016-01-01

    This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

  8. Pilot Greenhouse

    CERN Multimedia

    1983-01-01

    This pilot greenhouse was built in collaboration with the "Association des Maraichers" of Geneva in the frame of the study for making use of the heat rejected as warm water by CERN accelerators and experiments. Among other improvements, more automated and precise regulation systems for heating and ventilation were developed. See also 8305598X.

  9. Method of Converting Wheat Flour Quantity into Rice Flour Quantity in Cookies (Part-1)

    OpenAIRE

    村田,美穂子; 髙橋,由加

    2016-01-01

    A method of converting the wheat flour quantity of a recipe of wheat-flour cookies into the rice flour quantity of a recipe of rice-flour cookies used domestically for wheat-allergic children was studied. The proportion of the water content with respect to the flour content (the wheat or rice flour content) in cut cookies prepared according to a commercially available recipe was obtained. Next, four types of rice-flour cookies were prepared according to a recipe for wheat-flour cookies using ...

  10. Effective dose: a radiation protection quantity

    CERN Document Server

    Menzel, H G

    2012-01-01

    Modern radiation protection is based on the principles of justification, limitation, and optimisation. Assessment of radiation risks for individuals or groups of individuals is, however, not a primary objective of radiological protection. The implementation of the principles of limitation and optimisation requires an appropriate quantification of radiation exposure. The International Commission on Radiological Protection (ICRP) has introduced effective dose as the principal radiological protection quantity to be used for setting and controlling dose limits for stochastic effects in the regulatory context, and for the practical implementation of the optimisation principle. Effective dose is the tissue weighted sum of radiation weighted organ and tissue doses of a reference person from exposure to external irradiations and internal emitters. The specific normalised values of tissue weighting factors are defined by ICRP for individual tissues, and used as an approximate age- and sex-averaged representation of th...

  11. Pilot study

    International Nuclear Information System (INIS)

    Hofmeester, G.H.; Swart, A.; Dijk, E. van

    1984-01-01

    In May 1980 it was decided to organize an intercomparison of personal dosimeters for photon radiations. The Commission of the European Communities initiated the intercomparison by starting a pilot study in which three laboratories NPL (United Kingdom), PTB (Germany) and RIV (The Netherlands) were asked to irradiate a series of personal dosemeters from institutes, GSF (Muenchen), CEA (Fontenay-aux-Roses), CNEN (Bologna) and CEGB (Berkeley). The latter institutes are secondary standard laboratories and have a radiation protection service as well. A new aspect of this pilot study is the fact that the irradiations also take place in front of a phantom. Irradiations took place in July and August 1980. The results of 4 institutes show that the personal dosemeters are quite capable of measuring the backscattered photon components

  12. Category 3 threshold quantities for hazard categorization of nonreactor facilities

    International Nuclear Information System (INIS)

    Mandigo, R.L.

    1996-01-01

    This document provides the information necessary to determine Hazard Category 3 threshold quantities for those isotopes of interest not listed in WHC-CM-4-46, Section 4, Table 1.''Threshold Quantities.''

  13. Discounting of quantity surveying fees in South Africa

    African Journals Online (AJOL)

    by clients have forced Quantity Surveying firms into competition with ... Furthermore, 43% of consulting engineering firms were discounting their fees at a rate of .... Quantity. Surveying services are also offered in the fields of dispute resolution,.

  14. 41 CFR 101-27.102 - Economic order quantity principle.

    Science.gov (United States)

    2010-07-01

    ... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity...

  15. Relationships of chemical composition, quantity of milt to fertility and ...

    African Journals Online (AJOL)

    African Journal of Food, Agriculture, Nutrition and Development ... determining the right quantity of milt that can be used to fertilize certain quantity of eggs. ... quantity of milt used for artificial reproduction in fish significantly affect water quality used ... is the major organic substance that supplies the spermatozoa with energy.

  16. Six categories of ionizing radiation quantities practical in various fields

    International Nuclear Information System (INIS)

    Zheng Junzheng; Zhuo Weihai

    2011-01-01

    This paper is the part of review on the evolvement of the systems for ionizing radiation quantities and units. In the paper, for better understanding and correct use of the relevant quantities of ionizing radiation, the major ionizing radiation quantities in various fields are divided into six categories. (authors)

  17. 7 CFR 61.102 - Determination of quantity index.

    Science.gov (United States)

    2010-01-01

    ... the quantity index shall equal four times percentage of oil plus six times percentage of ammonia, plus 5. (b) For American Pima cottonseed the quantity index shall equal four times percentage of oil... 7 Agriculture 3 2010-01-01 2010-01-01 false Determination of quantity index. 61.102 Section 61.102...

  18. Modelling (vapour + liquid) and (vapour + liquid + liquid) equilibria of {water (H2O) + methanol (MeOH) + dimethyl ether (DME) + carbon dioxide (CO2)} quaternary system using the Peng-Robinson EoS with Wong-Sandler mixing rule

    International Nuclear Information System (INIS)

    Ye Kongmeng; Freund, Hannsjoerg; Sundmacher, Kai

    2011-01-01

    Highlights: → Phase behaviour modelling of H 2 O-MeOH-DME under pressurized CO 2 (anti-solvent) using PRWS. → PRWS-UNIFAC-PSRK has better performance than PRWS-UNIFAC-Lby in general. → Reliable to extend the VLE and VLLE phase behaviour from binary to multicomponent systems. → Successful prediction of the VLE and VLLE of binary, ternary, and quaternary systems. → Potential to apply the model for designing new DME separation process. - Abstract: The (vapour + liquid) equilibria (VLE) and (vapour + liquid + liquid) equilibria (VLLE) binary data from literature were correlated using the Peng-Robinson (PR) equation of state (EoS) with the Wong-Sandler mixing rule (WS). Two group contribution activity models were used in the PRWS: UNIFAC-PSRK and UNIFAC-Lby. The systems were successfully extrapolated from the binary systems to ternary and quaternary systems. Results indicate that the PRWS-UNIFAC-PSRK generally displays a better performance than the PRWS-UNIFAC-Lby.

  19. The covariance matrix of derived quantities and their combination

    International Nuclear Information System (INIS)

    Zhao, Z.; Perey, F.G.

    1992-06-01

    The covariance matrix of quantities derived from measured data via nonlinear relations are only approximate since they are functions of the measured data taken as estimates for the true values of the measured quantities. The evaluation of such derived quantities entails new estimates for the true values of the measured quantities and consequently implies a modification of the covariance matrix of the derived quantities that was used in the evaluation process. Failure to recognize such an implication can lead to inconsistencies between the results of different evaluation strategies. In this report we show that an iterative procedure can eliminate such inconsistencies

  20. Ursodeoxycholic Acid Can Improve Liver Transaminase Quantities in Children with Anticonvulsant Drugs Hepatotoxicity: a Pilot Study.

    Directory of Open Access Journals (Sweden)

    Masoumeh Asgarshirazi

    2015-06-01

    Full Text Available The present study has been directed to investigate Ursodeoxycholic Acid (UDCA effect in children, to reduce the high Liver transaminases induced by Anticonvulsant drugs (drug induced hepatitis. This idea has been driven from Cytoprotective and antioxidant properties of UDCA to be used in drug induced inflammation in Liver. Twenty two epileptic patients aged between 4 mo - 3 yr whom were under anticonvulsant therapy with drugs such as valperoic acid, primidone, levetiracetam, Phenobarbital or any combination of them and had shown Liver transaminases rise , after rule out of Viral-Autoimmune, Metabolic and Anatomic causes, have been prescribed UDCA in dose of 10-15 mg/kg/day, at least for 6 months. Any patient who have shown confusing factors such as genetic disorders with liver involvement or spontaneous decline in enzymes or had not treatment compliance has been excluded from the study. Transaminases range changes as well as Probable side effects of the drug have been monitored. The results indicated that UDCA is effective and well tolerable in the children with drug induced hyper transaminasemia. No side effect has been seen and recorded in this study. Based on this study and its results, we recommend UDCA as a safe and effective choice in drug induced hepatotoxicities.

  1. A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

    Science.gov (United States)

    Cravotta,, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

    2010-01-01

    Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

  2. Physical quantities, their role and treatment in gasflow measurement techniques

    International Nuclear Information System (INIS)

    Narjes, L.

    1977-06-01

    We begin by taking a closer look at the concepts physical quantity, dimension and unit of measurement. Then a survey is given of the physical quantities applied in gasflow measurement techniques. Here the volume-, as well as the mass-flow rate, as derived quantities are of particular interest. The application of these quantities in relation to the legal units of measurement is specifically described. In addition the quantity equation and further the quantity equation adapted to the use of suitable units and their modes of application are compared. In the appendix four examples clarify these modes. Special attention is paid to the quantity equation adapted to practically oriented units. The applications of this type of equation in VDI regulations, standards and other technical guidelines for measurement of flow are mentioned. Moreover, the meaning of the standard state for the comparison of flows of gaseous fluids is illustrated. The difficulties concerning an international agreement on uniform standard temperature are explained. Starting from there, the advantages of the fundamental quantity 'amount of substance' applied to the measurement of flow are described. The use of this quantity for the thermodynamic state of ideal and real gases, respectively gas mixtures, is demonstrated in the appendix by an example. (orig.) [de

  3. 48 CFR 52.217-6 - Option for Increased Quantity.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

  4. 41 CFR 109-27.102 - Economic order quantity principle.

    Science.gov (United States)

    2010-07-01

    ... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property...

  5. 48 CFR 916.504 - Indefinite-quantity contracts.

    Science.gov (United States)

    2010-10-01

    ... indefinite-quantity, multiple award contracts to ensure that adequate consideration exists to contractually... contracts. 916.504 Section 916.504 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Indefinite-Delivery Contracts 916.504 Indefinite-quantity...

  6. 30 CFR 75.322 - Harmful quantities of noxious gases.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Harmful quantities of noxious gases. 75.322... quantities of noxious gases. Concentrations of noxious or poisonous gases, other than carbon dioxide, shall... Governmental Industrial Hygienists in “Threshold Limit Values for Substance in Workroom Air” (1972). Detectors...

  7. Memory-Based Quantity Discrimination in Coyotes (Canis latrans

    Directory of Open Access Journals (Sweden)

    Salif Mahamane

    2014-08-01

    Full Text Available Previous research has shown that the ratio between competing quantities of food significantly mediates coyotes‘ (Canis latrans ability to choose the larger of two food options. These previous findings are consistent with predictions made by Weber‘s Law and indicate that coyotes possess quantity discrimination abilities that are similar to other species. Importantly, coyotes‘ discrimination abilities are similar to domestic dogs (Canis lupus familiaris, indicating that quantitative discrimination may remain stable throughout certain species‘ evolution. However, while previously shown in two domestic dogs, it is unknown whether coyotes possess the ability to discriminate visual quantities from memory. Here, we address this question by displaying different ratios of food quantities to 14 coyotes before placing the choices out of sight. The coyotes were then allowed to select one of either non-visible food quantities. Coyotes‘ discrimination of quantity from memory does not follow Weber‘s Law in this particular task. These results suggest that working memory in coyotes may not be adapted to maintain information regarding quantity as well as in domestic dogs. The likelihood of a coyote‘s choosing the large option increased when it was presented with difficult ratios of food options first, before it was later presented with trials using more easily discriminable ratios, and when the large option was placed on one particular side. This suggests that learning or motivation increased across trials when coyotes experienced difficult ratios first, and that location of food may have been more salient in working memory than quantity of food.

  8. Symbols and definitions of quantities and units in isotope stoichiometry

    International Nuclear Information System (INIS)

    Junghans, P.; Krumbiegel, P.; Faust, H.

    1982-01-01

    On the basis of the International System of Units and recent recommendations of the IUPAC on 'Symbols and Terminology for Physicochemical Quantities and Units' a system is proposed of uniform and unambiguous symbols and definitions of quantities and units used in the isotope dilution technique. The close relationship between isotope stoichiometry and common stoichiometry is demonstrated. (author)

  9. Variation in Quantity of Heat Produced from Charcoal of Prosopis ...

    African Journals Online (AJOL)

    Data were collected using the copper calorimeter, a thermometer, an air tight burner and a weight balance. The results showed a gradual decrease in the quantity of heat produced as combustion time increased from 10 40 minutes in all wood species. Significant differences (p<0.05) in the quantity of heat produced both ...

  10. 19 CFR 144.33 - Minimum quantities to be withdrawn.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Minimum quantities to be withdrawn. 144.33 Section 144.33 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... Warehouse § 144.33 Minimum quantities to be withdrawn. Unless by special authority of the Commissioner of...

  11. 21 CFR 1314.20 - Restrictions on sales quantity.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Restrictions on sales quantity. 1314.20 Section 1314.20 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RETAIL SALE OF SCHEDULED LISTED CHEMICAL PRODUCTS Sales by Regulated Sellers § 1314.20 Restrictions on sales quantity. (a) Without...

  12. Quantifying cannabis: A field study of marijuana quantity estimation.

    Science.gov (United States)

    Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

    2018-05-17

    The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  13. Project plans for transuranic waste at small quantity sites in the Department of Energy comples-10522

    International Nuclear Information System (INIS)

    Mctaggart, Jerri Lynne; Lott, Sheila; Gadbury, Casey

    2009-01-01

    Los Alamos National Laboratory, Carlsbad Office (LANL-CO), has been tasked to write Project Plans for all of the Small Quantity Sites (SQS) with defense related Transuranic (TRU) waste in the Department of Energy (DOE) complex. Transuranic Work-Off Plans were precursors to the Project Plans. LANL-CO prepared a Work-Off Plan for each small quantity site. The Work-Off Plan that identified issues, drivers, schedules, and inventory. Eight sites have been chosen to deinventory their legacy TRU waste; Bettis Atomic Power Laboratory, General Electric-Vallecitos Nuclear Center, Lawrence Berkeley National Laboratory, Lawrence Livermore National Laboratory-Area 300, Nevada Test Site, Nuclear Radiation Development, Sandia National Laboratory, and the Separations Process Research Unit. Each plan was written for contact and/or remote handled waste if present at the site. These project plans will assist the small quantity sites to ship legacy TRU waste offsite and de-inventory the site of legacy TRU waste. The DOE is working very diligently to reduce the nuclear foot print in the United States. Each of the eight SQSs will be de-inventoried of legacy TRU waste during a campaign that ends September 2011. The small quantity sites have a fraction of the waste that large quantity sites possess. During this campaign, the small quantity sites will package all of the legacy TRU waste and ship to Idaho or directly to the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The sites will then be removed from the Transuranic Waste Inventory if they are de-inventoried of all waste. Each Project Plan includes the respective site inventory report, schedules, resources, drivers and any issues. These project plans have been written by the difficult waste team and will be approved by each site. Team members have been assigned to each site to write site specific project plans. Once the project plans have been written, the difficult team members will visit the sites to ensure nothing has

  14. 75 FR 56857 - Pilot, Flight Instructor, and Pilot School Certification

    Science.gov (United States)

    2010-09-17

    ...-2006-26661; Amendment No., 141-14] RIN 2120-AI86 Pilot, Flight Instructor, and Pilot School..., certification, and operating requirements for pilots, flight instructors, ground instructors, and pilot schools...: Background On August 21, 2009, the FAA published the ``Pilot, Flight Instructor, and Pilot School...

  15. Concept of ICRU's operational quantity and its application

    International Nuclear Information System (INIS)

    Murakami, Hiroyuki

    1995-01-01

    The operational quantity which was introduced in the ICRU report 39 published in 1985 was shocking rather than fresh for the author. The report was translated into Japanese, but at the beginning, the contents were not able to be understood. Thereafter, the measurement of ICRU sphere dose equivalent was introduced in a national law. But it is feared that the understanding of this operational quantity is limited to specialist level, and is not by men of practical works. The meaning of ''operational'' must be that workers measure and obtain dose on the spot for the radiation protection for themselves. The principles used when ICRU considered the new practical measured quantity are shown. In the definition of operational quantity in area monitoring, two concepts of expanded and aligned connect real measurement with the operational quantity. The problems of measuring individual dose equivalent are discussed. As to the reality of applying the operational quantity, the fundamentals of the calibration of measuring instruments, the investigation of the operational quantity in relation to measuring instruments and measurement mode, and the relation of area monitoring and individual monitoring are described. (K.I.)

  16. Conceptual Model of Quantities, Units, Dimensions, and Values

    Science.gov (United States)

    Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

    2011-01-01

    JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

  17. Pilot Boarding Areas

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Pilot boarding areas are locations at sea where pilots familiar with local waters board incoming vessels to navigate their passage to a destination port. Pilotage is...

  18. Layer-Mean Quantities, Local Conservation Laws, and Vorticity

    International Nuclear Information System (INIS)

    Camassa, R.; Levermore, C.D.

    1997-01-01

    We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

  19. Impact of the Velo 2 half misalignment on physical quantities

    CERN Document Server

    Roguljic, Matej; Borghi, Silvia; Grillo, Lucia; CERN. Geneva. EP Department

    2016-01-01

    The impact of the misalignment of the Vertex Locator of the LHCb experiment on the physical quantities of the decay "$D^{*+} \\rightarrow (D^{0}\\rightarrow K^{-}\\pi^{+}) \\pi^{+} $" is studied in this note. Different misalignments of the 2 halves are applied to Monte Carlo data and the variations of the physical quantities with respect to the case without misalignment are evaluated. The results show the importance of the VELO 2 half alignment which can significantly affect the physics performance in the large misalignment case. A misalignment equal to the precision of the real-time alignment of the Vertex Locator is found to have a negligible effect on the studied physical quantities.

  20. New quantities in radiation protection and conversion coefficients

    International Nuclear Information System (INIS)

    1986-01-01

    Four new quantities have been proposed by the ICRP for use in radiation protection from external sources, i.e. the ambient dose equivalent, the directional dose equivalent, the individual dose equivalent (penetrating), and the individual dose equivalent (superficial). These quantities are briefly described together with two new concepts of expanded and aligned fields. The BCRU recommends that these quantities should be adopted for use in the UK together with conversion coefficients when re-calibrating existing instruments, reporting the results of measurements and designing instruments. (UK)

  1. A note on the expectation and deviation of physical quantities

    International Nuclear Information System (INIS)

    Nagasawa, Masao

    2009-01-01

    By using the function representation of self-adjoint operators, the expectation and variance of physical quantities (self-adjoint operators) are defined, and it is shown that the so-called uncertainty principle does not hold.

  2. The ICRU dose equivalence quantities in radiation protection

    International Nuclear Information System (INIS)

    Grimbergen, T.W.M.

    1990-09-01

    The definitions and application of the new ICRU radiation protection quantities have been reviewed and studied in literature. Special emphasis was laid on the consequences of the use of the new quantities by personnel dosimetry services, and on the consequences of the use of the new quantities during an intercomparison programme for dosimetry services. The study shows that the recommendations of the ICRU are not yet complete and not fully realizable. This means that the dosimetry services always have to make certain approximations, when they use the new quantities. In literature, several approaches have been proposed. The feasibility of an approach depends on the characteristics of the dosimeters used. The use of different approaches by the dosimetry services is thought to be of possible influence on the results of an intercomparison programme. (author). 42 refs.; 3 figs.; 1 tab

  3. Foreign materials in the repository - update of estimated quantities

    International Nuclear Information System (INIS)

    Hagros, A.

    2007-03-01

    In a repository for spent nuclear fuel, a variety of materials are used during the construction process and during the operation of the repository. In addition to materials necessary for the construction and operation, some materials may be transported into the repository through the ventilation air, as emissions from vehicles, as waste produced by the staff etc. Both of these two types of materials are considered here and their quantities - both the introduced quantities and the quantities that remain after closure - in the repository constructed at Olkiluoto in Eurajoki, Finland are estimated here based on new information. This work is intended to update the estimations that have been made previously, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility ONKALO at Olkiluoto. During this construction process, the quantities of the different construction materials introduced into the underground openings have been monitored and they form a basis for estimating the quantities to be used in the future. The estimations made in this report are specific to a KBS-3V type repository and to the Olkiluoto site, although in some cases more generic information has been used, particularly when the relevant quantities have not been monitored in the ONKALO. The estimations are based on the new repository layout produced in 2006 and consider the latest plans for grouting and rock support. As these plans are generally not final yet, several different alternative plans are assumed when necessary. Also two different strategies for the backfilling of the tunnels are considered. The most significant differences with respect to the results of an earlier estimation are related to the materials used in grouting, shotcreting and in support bolts. In the cases where a mixture of bentonite and crushed rock is the used backfill alternative, gypsum and cement are the materials with the largest quantities remaining in the

  4. Import and export of small quantities of nuclear materials

    International Nuclear Information System (INIS)

    Grenier, M.

    1986-06-01

    Administrative procedures for import export of nuclear materials are specific for each country. In France regulations are reviewed for small quantities, lower threshold, in some cases, allows a simplified procedure, however thresholds are not the same in the different texts (and for one of them, concerning proliferation, is zero). It is obvious that regulations are necessary even for small quantities but national and international threshold should be harmonized [fr

  5. Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports

    Science.gov (United States)

    2017-12-01

    by the Army Acquisition Executive contains the following language . As a recently delegated Acquisition Category IC program, the AH-64E Apache...Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis, Project Leader Margaret L. Giles David M. Tate I...F E N S E A N A L Y S E S IDA Paper P-8490 Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis

  6. Charaterisation of function spaces via mollification; fractal quantities for distributions

    Directory of Open Access Journals (Sweden)

    Hans Triebel

    2003-01-01

    Full Text Available The aim of this paper is twofold. First we characterise elements f belonging to the Besov spaces Bpqs(ℝn with s∈ℝ,  0quantities for distributions generalising well-known corresponding quantities for Radon measures.

  7. Information quantity in a pixel of digital image

    OpenAIRE

    Kharinov, M.

    2014-01-01

    The paper is devoted to the problem of integer-valued estimating of information quantity in a pixel of digital image. The definition of an integer estimation of information quantity based on constructing of the certain binary hierarchy of pixel clusters is proposed. The methods for constructing hierarchies of clusters and generating of hierarchical sequences of image approximations that minimally differ from the image by a standard deviation are developed. Experimental results on integer-valu...

  8. Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

    Science.gov (United States)

    Hurda, Lukáš; Matas, Richard

    2017-09-01

    Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

  9. Testing quantity theory of money for the Turkish economy

    OpenAIRE

    Levent, Korap

    2007-01-01

    In this paper, it is tried to test the main assumptions of the Quantity Theory of Money for the Turkish economy. Using some contemporaneous estimation techniques to examine the long-run stationary economic relationships on which the quantity theory is constructed, it is found that stationary characteristics of the velocitities of narrowly and broadly defined monetary aggregates cannot be rejected. However, monetary aggregates seem to be endogenous for the long-run evoluation of prices and rea...

  10. Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

    International Nuclear Information System (INIS)

    Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

    2008-01-01

    The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

  11. Application of an experimental irradiation facility type K-120 for the radiation treatment of agricultural products in large quantity

    International Nuclear Information System (INIS)

    Stenger, V.; Foeldiak, G.; Horvath, I.; Hargittai, P.; Bartfai, Cs.

    1979-01-01

    During experimental and pilot irradiation carried out by the 60 Co irradiation facility type K-120 of the Institute of Isotopes of the Hungarian Academy of Sciences an irradiation technology for the treatment of agricultural and food products of considerable density has been developed. Applying transport containers of commercial size the intermittent radiation treatment of great quantity products was made possible with homogeneous dose distribution. The radiation technical characteristics, the utilization coefficient and the capacity of the facility for every agricultural product were calculated. (author)

  12. Trained Quantity Abilities in Horses (Equus caballus: A Preliminary Investigation

    Directory of Open Access Journals (Sweden)

    Maria Elena Miletto Petrazzini

    2014-07-01

    Full Text Available Once believed to be a human prerogative, the capacity to discriminate between quantities now has also been reported in several vertebrates. To date, only two studies investigated numerical abilities in horses (Equus caballus but reported contrasting data. To assess whether horses can be trained to discriminate between quantities, I have set up a new experimental protocol using operant conditioning. One adult female was trained to discriminate between 1 and 4 (Test 1 in three different conditions: non-controlled continuous variables (numerical and continuous quantities that co-vary with number are simultaneously available, 50% controlled continuous variables (intermediate condition, and 100% controlled continuous variables (only numerical information available. The subject learned the discrimination in all conditions, showing the capacity to process numerical information. When presented with a higher numerical ratio (2 vs. 4, Test 2, the subject still discriminated between the quantities but its performance was statistically significant only in the non-controlled condition, suggesting that the subject used multiple cues in presence of a more difficult discrimination. On the whole, the results here reported encourage the use of this experimental protocol as a valid tool to investigate the capacity to process numerical and continuous quantities in horses in future research.

  13. Processing ordinality and quantity: the case of developmental dyscalculia.

    Directory of Open Access Journals (Sweden)

    Orly Rubinsten

    Full Text Available In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1 the traditionally and well accepted numerical magnitude system but also (2 core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD. Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1 and 3 numbers (symbolic task: Experiment 2. In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks, DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

  14. Processing ordinality and quantity: the case of developmental dyscalculia.

    Science.gov (United States)

    Rubinsten, Orly; Sury, Dana

    2011-01-01

    In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

  15. Quantities of natural gas transported in January-December 2009

    International Nuclear Information System (INIS)

    2010-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2009: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  16. Quantities of natural gas transported in August-December 2007

    International Nuclear Information System (INIS)

    2008-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the available monthly key figures of GRTgaz activity from August to December 2007: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  17. BIRTHDAY CAKE ACTIVITY STRUCTURED ARRANGEMENT FOR HELPING CHILDREN DETERMINING QUANTITIES

    Directory of Open Access Journals (Sweden)

    Neni Mariana

    2010-07-01

    Full Text Available Few researches have been concerned about relation between children’s spatialthinking and number sense. Narrowing for this small research, we focused onone component of spatial thinking, that is structuring objects, and onecomponent of number senses, that is cardinality by determining quantities. Thisstudy focused on a design research that was conducted in Indonesia in which weinvestigated pre-school children’s (between 2 and 3.5 years old ability inmaking structured arrangement and their ability to determine the quantities bylooking at the arrangements. The result shows us that some of the children wereable to make such arrangement. However, the children found difficulties eitherto determine quantities from those arrangements or to compare some structuresto easily recognize number of objects.Keywords: structures, structured arrangement, cardinality DOI: http://dx.doi.org/10.22342/jme.1.1.790.53-70

  18. Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

    Directory of Open Access Journals (Sweden)

    Neni Mariana

    2010-07-01

    Full Text Available Few researches have been concerned about relation between children’s spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was conducted in Indonesia in which we investigated pre-school children’s (between 2 and 3.5 years old ability in making structured arrangement and their ability to determine the quantities by looking at the arrangements. The result shows us that some of the children were able to make such arrangement. However, the children found difficulties either to determine quantities from those arrangements or to compare some structures to easily recognize number of objects.

  19. Multimodal semantic quantity representations: further evidence from Korean Sign Language

    Directory of Open Access Journals (Sweden)

    Frank eDomahs

    2012-01-01

    Full Text Available Korean deaf signers performed a number comparison task on pairs of Arabic digits. In their RT profiles, the expected magnitude effect was systematically modified by properties of number signs in Korean Sign Language in a culture-specific way (not observed in hearing and deaf Germans or hearing Chinese. We conclude that finger-based quantity representations are automatically activated even in simple tasks with symbolic input although this may be irrelevant and even detrimental for task performance. These finger-based numerical representations are accessed in addition to another, more basic quantity system which is evidenced by the magnitude effect. In sum, these results are inconsistent with models assuming only one single amodal representation of numerical quantity.

  20. How tobacco companies have used package quantity for consumer targeting.

    Science.gov (United States)

    Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

    2018-05-31

    Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  1. Foreign materials in the repository. Update of estimated quantities

    International Nuclear Information System (INIS)

    Karvonen, T.

    2011-06-01

    A variety of materials are used during the construction process and the operation of the repository for spent nuclear fuel at Olkiluoto in Eurajoki, Finland. In addition to materials necessary for the construction and operation, some materials may be transported into the repository with the ventilation air, as emissions from vehicles etc. Both of these two types of materials are considered here and both introduced quantities and the quantities that remain after the closure in the repository are estimated here based on the most recent information. This work is intended to update the previous estimations, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility called ONKALO at Olkiluoto. The implemented quantities as well as designs and preliminary designs have been used in calculating the quantities of the foreign materials. The estimations made in this report are specific to a KBS-3V type repository. In some cases more generic information has been used, particularly when the relevant quantities have not been monitored in ONKALO. The estimations are based on the new repository layout produced in 2010 and consider the latest plans for grouting and rock support. As all of these plans are not final some quantities may change in the future. As the repository layout may still go through some changes this report also provides the foreign materials for a hundred meters of different deposition tunnels designed for the OL and LO type canisters1. The results have also been calculated for a space demanded by a deposition tunnel end plug and the tunnel lengths before and after one. The most significant foreign materials are certain accessory minerals of the clay materials followed by organic materials (including the organic carbon from the clay materials), cement, steel and silica. (orig.)

  2. A shared system of representation governing quantity discrimination in canids

    Directory of Open Access Journals (Sweden)

    Joseph M Baker

    2012-10-01

    Full Text Available One way to investigate the evolution of cognition is to compare the abilities of phylogenetically related species. The domestic dog (Canis lupus familiaris, for example, still shares cognitive abilities with the coyote (C. latrans. Both of these canids possess the ability to make psychophysical less/more discriminations of food based on quantity. Like many other species including humans, this ability is mediated by Weber’s Law: discrimination of continuous quantities is dependent on the ratio between the two quantities. As two simultaneously presented quantities of food become more similar, choice of the large or small option becomes random in both dogs and coyotes. It remains unknown, however, whether these closely related species within the same family—one domesticated, and one wild—make such quantitative comparisons with comparable accuracy. Has domestication honed or diminished this quantitative ability? Might different selective and ecological pressures facing coyotes drive them to be more or less able to accurately represent and discriminate food quantity than domesticated dogs? This study is an effort to elucidate this question concerning the evolution of non-verbal quantitative cognition.Here, we tested the quantitative discrimination ability of 16 domesticated dogs. Each animal was given 9 trials in which two different quantities of food were simultaneously displayed to them. The domesticated dogs’ performance on this task was then compared directly to the data from 16 coyotes’ performance on this same task reported by Baker and colleagues (2011.The quantitative discrimination abilities between the two species were strikingly similar. Domesticated dogs demonstrated similar quantitative sensitivity as coyotes, suggesting that domestication may not have significantly altered the psychophysical discrimination abilities of canids. Instead, this study provides further evidence for similar nonverbal quantitative abilities across

  3. Quality or Quantity: A Statement for Teacher Training in Turkey

    Directory of Open Access Journals (Sweden)

    Ali AZAR

    2011-01-01

    Full Text Available Developed countries are initiating and implementing effective and appropriate technics in the field of teacher training. In Turkey, much research has been done in order to determine the qualification of teachers and, by this way, to train qualified teachers. Ministry of Education, Turkish Council of Higher Education, Faculties of Education and Faculties of Sciences have cooperated some certification systems, however, the research which is not supported by preliminary studies but exposured to political coercions lowered the quality of education. Besides, quantity is increased by pedagogical formation programs. In this study, Turkish teacher training system is analyzed with respect to quantity and quality.

  4. Manual of symbols and terminology for physicochemical quantities and units

    CERN Document Server

    Whiffen, D H

    2013-01-01

    Manual of Symbols and Terminology for Physicochemical Quantities and Units, 1979 Edition contains physical quantity tabulations of products. The Commission on Symbols, Terminology, and Units is a part of the Division of Physical Chemistry of the International Union of Pure and Applied Chemistry. Its general responsibilities are to secure clarity and precision, and wider agreement in the use of symbols, by chemists in different countries, among physicists, chemists, and engineers, and by editors of scientific journals. This book is composed of 13 chapters, and begins with the determination o

  5. Units for physical quantities used in dosimetry and radiation protection

    Energy Technology Data Exchange (ETDEWEB)

    Taubert, R; Wagner, S

    1976-04-01

    The 15th General Conference on Weights and Measures (1975) decided to introduce the name Becquerel for the SI unit of the quantity activity (1 Bq = 1 s/sup -1/) and the name Gray for the SI unit of ionizing radiations (1 Gy = 1 J/kg). The consequences of this latter decision are discussed. The Bundesanstalt is of the opinion that no further names for this unit should be introduced, but that the Gray should be used also for other quantities of the same dimension, especially for the dose equivalent.

  6. Studies on quantity and composition of dairy cow excreta

    International Nuclear Information System (INIS)

    Peschke, H.

    1982-01-01

    After feeding a lactating dairy cow a day ration completely enriched with 15 N, the quantities of feces and urine were registered over a period of ten days and put into proportion to the animal mass. The fecal dry matter was put into proportion to the dry matter of the fodder by means of 15 N analysis the N excretion with the excreta was determined concerning quantity and time. Selected feces and urine charges were used to produce a slurry model. The content of nutritive elements of the initial components and of the organic fertilizer are discussed. (author)

  7. Photosynthesis-related quantities for education and modeling.

    Science.gov (United States)

    Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

    2013-11-01

    A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

  8. Quantities of natural gas transmitted in January-December 2012. Quantities of natural gas transported in January-December 2012

    International Nuclear Information System (INIS)

    2013-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2012: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  9. Teacher quality and quantity as correlates of secondary school ...

    African Journals Online (AJOL)

    This study investigated the twin variables of quality and quantity of teachers as correlates of secondary school academic performance in Ogun State of Nigeria between 1997/98 and 2000/2001 academic sessions. The study was conducted ex-post facto under a descriptive survey research design using the proportional to ...

  10. 16 CFR 1.23 - Quantity limit rules.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

  11. Food quantity affects the sensitivity of Daphnia to road salt.

    Science.gov (United States)

    Brown, Arran H; Yan, Norman D

    2015-04-07

    Road deicing operations have raised chloride (Cl) levels in many temperate lakes in Europe and North America. These lakes vary widely in trophic status, but to date, no one has quantified the interaction between food quantity and road salt toxicity. We examined the effects of food quantity (particulate algal C concentration (C)) on the chronic toxicity of Cl to Daphnia in soft-water bioassays. There was a strong positive linear relationship (r(2) = 0.92 for NaCl and r(2) = 0.96 for CaCl2) between food quantity and Cl LC50. As food quantity increased from 0.2 to 1.0 mg C/L (levels characteristic of oligotrophic to eutrophic lakes, respectively), the chronic Cl LC50 increased from 55.7 to 284.8 mg Cl/L. Salt type (NaCl or CaCl2) did not affect the Cl LC50, Daphnia life history parameters, or the intrinsic rate of population increase (r). The life history parameter most sensitive to Cl was neonate production. Cl did not inhibit egg production, nor was the maternal lipid investment in eggs changed, but egg viability and the subsequent release of live neonates decreased as Cl levels increased and food decreased. Our results suggest the trophic status of lakes should be considered when assessing ecological threat from Cl.

  12. Quantity, Quality, and Satisfaction with Mentoring: What Matters Most?

    Science.gov (United States)

    Xu, Xiaohong; Payne, Stephanie C.

    2014-01-01

    According to Kram's mentor role theory, satisfaction with mentoring and mentorship quality are key indicators of effective and successful mentoring. We contribute to mentoring research by demonstrating the relative importance of mentorship quantity, mentorship quality, and satisfaction with mentoring to the prediction of job satisfaction,…

  13. 19 CFR 351.409 - Differences in quantities.

    Science.gov (United States)

    2010-04-01

    ... DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.409... comparing export price or constructed export price with normal value, the Secretary will make a reasonable... section 773(a)(6)(C)(i) of the Act.) (b) Sales with quantity discounts in calculating normal value. The...

  14. Color Coding of Circuit Quantities in Introductory Circuit Analysis Instruction

    Science.gov (United States)

    Reisslein, Jana; Johnson, Amy M.; Reisslein, Martin

    2015-01-01

    Learning the analysis of electrical circuits represented by circuit diagrams is often challenging for novice students. An open research question in electrical circuit analysis instruction is whether color coding of the mathematical symbols (variables) that denote electrical quantities can improve circuit analysis learning. The present study…

  15. Thermodynamic quantities for the Klein–Gordon equation

    Indian Academy of Sciences (India)

    We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverselinear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation.We use a method based on the Euler–MacLaurin formula to analytically compute thethermal ...

  16. Thermodynamic quantities for the Klein–Gordon equation with a ...

    Indian Academy of Sciences (India)

    2017-02-01

    Feb 1, 2017 ... Abstract. We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverse- linear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation. We use a method based on the Euler–MacLaurin formula to ...

  17. Conserved quantities for stationary Einstein-Maxwell space-times

    International Nuclear Information System (INIS)

    Esposito, F.P.; Witten, L.

    1978-01-01

    It is shown that every stationary Einstein-Maxwell space-time has eight divergence-free vector fields and these are isolated in general form. The vector fields and associated conserved quantities are calculated for several families of space-times. (Auth.)

  18. Photographs in Dutch History Textbooks: Quantity, type and educational use

    NARCIS (Netherlands)

    M. Kleppe (Martijn)

    2010-01-01

    textabstractThis article demonstrates a media scientific approach by studying the use of photographs in Dutch History textbooks for High School pupils in the period 1970 – 2000. The quantity of photos has been determined as well as the types of pictures and its use as educational tool. Results show

  19. A colorimeter for measurement of picomole quantities of urea.

    Science.gov (United States)

    Vurek, G G; Knepper, M A

    1982-04-01

    We described a new colorimeter for the measurement of picomole quantities of urea in nanoliter volume fluid samples. The diacetyl monoxime reaction was used to produce a colored product from urea. The method is capable of resolving differences of 10 pmoles between samples containing 0 to 225 pmoles.

  20. Estimating waste disposal quantities from raw waste samples

    International Nuclear Information System (INIS)

    Negin, C.A.; Urland, C.S.; Hitz, C.G.; GPU Nuclear Corp., Middletown, PA)

    1985-01-01

    Estimating the disposal quantity of waste resulting from stabilization of radioactive sludge is complex because of the many factors relating to sample analysis results, radioactive decay, allowable disposal concentrations, and options for disposal containers. To facilitate this estimation, a microcomputer spread sheet template was created. The spread sheet has saved considerable engineering hours. 1 fig., 3 tabs

  1. Do Speakers and Listeners Observe the Gricean Maxim of Quantity?

    Science.gov (United States)

    Engelhardt, Paul E.; Bailey, Karl G. D.; Ferreira, Fernanda

    2006-01-01

    The Gricean Maxim of Quantity is believed to govern linguistic performance. Speakers are assumed to provide as much information as required for referent identification and no more, and listeners are believed to expect unambiguous but concise descriptions. In three experiments we examined the extent to which naive participants are sensitive to the…

  2. Whither the Nigerian Quantity Surveyors in the Information ...

    African Journals Online (AJOL)

    The paucity of information on the computing status of the quantity surveyors in Nigeria have been scanty and without empirical substantiation. The basic platform for entry to the information technology gateway is the acquisition, adoption and utilization of the computer. Baseline information is therefore indispensable for the ...

  3. Water quantity and quality at the urban-rural interface

    Science.gov (United States)

    Ge Sun; B. Graeme Lockaby

    2012-01-01

    Population growth and urban development dramatically alter natural watershed ecosystem structure and functions and stress water resources. We review studies on the impacts of urbanization on hydrologic and biogeochemical processes underlying stream water quantity and water quality issues, as well as water supply challenges in an urban environment. We conclude that...

  4. Hazardous Waste Management for the Small Quantity Generator. Teacher Edition.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

    This instructional package for teaching about the regulations imposed on small quantity generators by the Environmental Protection Agency (EPA) under the Resource Conservation Recovery Act is organized around ll program objectives: students will be able to (l) determine a hazardous waste from lists or by identifying characteristics; (2) identify…

  5. Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

    Science.gov (United States)

    Mariana, Neni

    2010-01-01

    Few researches have been concerned about relation between children's spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was…

  6. 7 CFR 1427.170 - Quantity for loan.

    Science.gov (United States)

    2010-01-01

    ... to the preservation or safety of the loan collateral. Loans may be made on a lower percentage basis... 7 Agriculture 10 2010-01-01 2010-01-01 false Quantity for loan. 1427.170 Section 1427.170... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Recourse Seed Cotton Loans § 1427.170...

  7. Quantity and quality of written feedback, action plans, and student ...

    African Journals Online (AJOL)

    Background. Mini-clinical-evaluation exercise (mini-CEX) assessment forms that have been modified with the addition of specific spaces on separate sheets are expected to improve the quantity and quality of written feedback and the action plan for further learning which is agreed upon, and to encourage written reflection.

  8. Is the dose equivalent index a quantity to be measured

    International Nuclear Information System (INIS)

    Wagner, S.R.

    1980-01-01

    The following modifying factors are briefly considered in relation to the ambiguities and limitations of the Dose Equivalent Index: 1) Variations with time or of the movement of the exposed person 2) Irradiation geometry 3) Effect of radiation energy 4) Instrument performance and calibration, and other operational quantities. (U.K.)

  9. Threshold quantities for infectious diseases in periodic environments

    NARCIS (Netherlands)

    Heesterbeek, J.A.P.; Roberts, M.G.

    1995-01-01

    In this short note we give threshold quantities that determine the stability of the infection-free steady state for periodic deterministic systems that describe the spread of infectious diseases in populations whose individuals can be divided into a finite number of distinct groups. We concentrate

  10. Preparing Pilots for Takeoff

    Science.gov (United States)

    Ravage, Barbara

    2012-01-01

    Why would schools consider partnering with a vendor to operate a pilot? Why not just wait until the final product is released? For starters, pilots provide schools with a golden opportunity to get an early look at the software, take it for a test flight, and ask for changes tailored to their operating environment and business needs. In some cases,…

  11. A Little Here, A Little There, A Fairly Big Problem Everywhere: Small Quantity Site Transuranic Waste Disposition Alternatives

    International Nuclear Information System (INIS)

    Luke, Dale Elden; Parker, Douglas Wayne; Moss, J.; Monk, Thomas Hugh; Fritz, Lori Lee; Daugherty, B.; Hladek, K.; Kosiewicx, S.

    2000-01-01

    Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

  12. A little here, a little there, a fairly big problem everywhere: Small-quantity-site transuranic waste disposition alternatives

    International Nuclear Information System (INIS)

    D. Luke; D. Parker; J. Moss; T. Monk; L. Fritz; B. Daugherty; K. Hladek; S. Kosiewicx

    2000-01-01

    Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound Laboratory. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

  13. Role of Leadership in Transforming the Profession of Quantity Surveying

    Directory of Open Access Journals (Sweden)

    George Ofori

    2012-11-01

    Full Text Available The construction industry is facing a period of change. The roles ofthe professions involved in the industry in general, and of quantitysurveyors in particular, are also changing. There are opportunitiesfor surveyors to seize the initiative to broaden their involvement inprojects, and attain strategic positions within the industry. However,they will have to improve upon their skill sets and their knowledgebases. Senior quantity surveyors interviewed in Singapore sharedtheir views on the challenges facing the construction industry,and their profession. They suggested that the quantity surveyingprofession would only be able to address the pressing issues itfaces if it pays more attention to innovation and the development ofits people. It should be able to attract and retain talent. Knowledgemanagement will be of critical importance. This will be enabled andfacilitated by knowledge leadership.

  14. Does quantity generate quality? Testing the fundamental principle of brainstorming.

    Science.gov (United States)

    Muñoz Adánez, Alfredo

    2005-11-01

    The purpose of this work is to test the chief principle of brainstorming, formulated as "quantity generates quality." The study is included within a broad program whose goal is to detect the strong and weak points of creative techniques. In a sample of 69 groups, containing between 3 and 8 members, the concurrence of two commonly accepted criteria was established as a quality rule: originality and utility or value. The results fully support the quantity-quality relation (r = .893): the more ideas produced to solve a problem, the better quality of the ideas. The importance of this finding, which supports Osborn's theory, is discussed, and the use of brainstorming is recommended to solve the many open problems faced by our society.

  15. On the operational quantity Hp(3) for eye lens dosimetry

    International Nuclear Information System (INIS)

    Behrens, R

    2012-01-01

    In the past the operational quantity H p (3) has been defined for calibration purposes in a slab phantom. Recently, an additional phantom in the form of a cylinder was suggested for eye lens dosimetry as a cylinder much better approximates the shape of a head than a slab. Therefore, this work investigates whether the quantity H p (3), when defined in the respective calibration phantom, adequately estimates the eye lens dose (or is at least conservative) depending on the phantom: it turns out that in most cases both calibration phantoms are similarly well suited. Finally, the definition of the eye lens dose is discussed together with possible consequences on the definition of H p (3): the consideration of only the radiation sensitive volume of the lens causes H p (3) not to be conservative in beta radiation fields. (paper)

  16. Dimensions of Organisational Culture in Quantity Surveying Firms in Nigeria

    Directory of Open Access Journals (Sweden)

    Ayokunle Olubunmi Olanipekun

    2014-12-01

    Full Text Available The functionalist paradigm of organisational culture (OC views culture as a variable subject to conscious manipulation and control in order to solve organisational challenges. Therefore, this paper provides information on how OC is a solution to the challenges in Quantity Surveying firms (QSFs.  This was achieved by eliciting the dimensions of OC in forty two QSFs in Lagos, Nigeria, which are the business, people and external environment dimensions. The paper concludes that OC is a relevant solution to the identity and management related challenges in QSFs. Specifically, the paper informs on the implications of business and people dimensions of OC as a solution to the identity challenges, as well as on the implication of the external environment dimension of OC to the management challenges. Based on the findings, practical implications and recommendations were directed at the management and employees QSs in QSFs and Quantity Surveying researchers.

  17. Conserved quantities for generalized KdV equations

    International Nuclear Information System (INIS)

    Calogero, F.; Rome Univ.; Degasperis, A.; Rome Univ.

    1980-01-01

    It is noted that the nonlinear evolution equation usub(t) = α(t)usub(xxx) - 6ν(t) usub(x)u, u is identical to u(x,t), possesses three (and, in some cases, four) conserved quantities, that are explicitly displayed. These results are of course relevant only to the cases in which this evolution equation is not known to possess an infinite number of conserved quantities. Purpose and scope of this paper is to report three or four simple conservation laws possessed by the evolution equation usub(t) = α(t)usub(xxx) - 6ν(t)usub(x)u, u is identical to u(x,t). (author)

  18. Securing water quality and quantity: Research and development perspective

    CSIR Research Space (South Africa)

    Pienaar, H

    2012-10-01

    Full Text Available : ? economic growth & development ? human & environmental needs ? meeting international obligations ? energy needs (strategic water users) ? ensuring availability and allocation (all other users) ? CSIR 2012 Slide 3 Background ? SA 30th driest country... and quantity: Research and development perspective 4th Biennial Conference Harrison Pienaar 10 October 2012 Presentation outline ? Introduction and background to water in South Africa ? Transboundary water resource aspects ? Water related challenges...

  19. Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

    CERN Document Server

    Matubayasi, Norihiro

    2013-01-01

    Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

  20. Synthesis of bulk quantity BN nanotubes with uniform morphology

    International Nuclear Information System (INIS)

    Wen, G.; Zhang, T.; Huang, X.X.; Zhong, B.; Zhang, X.D.; Yu, H.M.

    2010-01-01

    Bulk quantity hexagonal BN nanotubes (h-BNNTs) with uniform morphology were synthesized via an improved ball-milling and annealing method. The sample was characterized by X-ray photoelectron spectrometry, electron energy loss spectroscopy, X-ray diffraction, scanning electron microscopy, conventional transmission electron microscopy (TEM) and high-resolution TEM. The results show that the fabricated BNNTs have a uniform diameter ranging from 80 to 100 nm and a length of about 50-60 μm.

  1. Monitoring the eye lens: which dose quantity is adequate?

    International Nuclear Information System (INIS)

    Behrens, R; Dietze, G

    2010-01-01

    Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity H p (0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity H p (3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of H p (0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of H p (3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of H p (0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

  2. Mass spectrometry of submicrogram quantities of lead and cadmium

    International Nuclear Information System (INIS)

    Moraes, Noemia M.P. de; Kakazu, M.H.; Iyer, S.S.

    1980-01-01

    Isotope analyses of submicrogram quantities of lead and cadmium are carried out by single filament solid source mass spectrometry. Thermionic emission of Pb and Cd is enhanced using silica gel as an emitter. Details of the chemical and mass spectrometric techniques are described. The low blank levels are maintained by extra purification of the reagents. The applications of isotope ratios of Pb and Cd in environmental sciences and geochemistry are discussed. (Author) [pt

  3. Effects of nonindigenous invasive species on water quality and quantity

    Science.gov (United States)

    Frank H. McCormick; Glen C. Contreras; Sherri L. Johnson

    2010-01-01

    Physical and biological disruptions of aquatic systems caused by invasive species alter water quantity and water quality. Recent evidence suggests that water is a vector for the spread of Sudden Oak Death disease and Port-Orfordcedar root disease. Since the 1990s, the public has become increasingly aware of the presence of invasive species in the Nation’s waters. Media...

  4. Multidemand Multisource Order Quantity Allocation with Multiple Transportation Alternatives

    Directory of Open Access Journals (Sweden)

    Jun Gang

    2015-01-01

    Full Text Available This paper focuses on a multidemand multisource order quantity allocation problem with multiple transportation alternatives. To solve this problem, a bilevel multiobjective programming model under a mixed uncertain environment is proposed. Two levels of decision makers are considered in the model. On the upper level, the purchaser aims to allocate order quantity to multiple suppliers for each demand node with the consideration of three objectives: total purchase cost minimization, total delay risk minimization, and total defect risk minimization. On the lower level, each supplier attempts to optimize the transportation alternatives with total transportation and penalty costs minimization as the objective. In contrast to prior studies, considering the information asymmetry in the bilevel decision, random and fuzzy random variables are used to model uncertain parameters of the construction company and the suppliers. To solve the bilevel model, a solution method based on Kuhn-Tucker conditions, sectional genetic algorithm, and fuzzy random simulation is proposed. Finally, the applicability of the proposed model and algorithm is evaluated through a practical case from a large scale construction project. The results show that the proposed model and algorithm are efficient in dealing with practical order quantity allocation problems.

  5. Entropy and Its Correlations with Other Related Quantities

    Directory of Open Access Journals (Sweden)

    Jing Wu

    2014-02-01

    Full Text Available In order to find more correlations between entropy and other related quantities, an analogical analysis is conducted between thermal science and other branches of physics. Potential energy in various forms is the product of a conserved extensive quantity (for example, mass or electric charge and an intensive quantity which is its potential (for example, gravitational potential or electrical voltage, while energy in specific form is a dissipative quantity during irreversible transfer process (for example mechanical or electrical energy will be dissipated as thermal energy. However, it has been shown that heat or thermal energy, like mass or electric charge, is conserved during heat transfer processes. When a heat transfer process is for object heating or cooling, the potential of internal energy U is the temperature T and its potential “energy” is UT/2 (called entransy and it is the simplified expression of thermomass potential energy; when a heat transfer process is for heat-work conversion, the potential of internal energy U is (1 − T0/T, and the available potential energy of a system in reversible heat interaction with the environment is U − U0 − T0(S − S0, then T0/T and T0(S − S0 are the unavailable potential and the unavailable potential energy of a system respectively. Hence, entropy is related to the unavailable potential energy per unit environmental temperature for heat-work conversion during reversible heat interaction between the system and its environment. Entropy transfer, like other forms of potential energy transfer, is the product of the heat and its potential, the reciprocal of temperature, although it is in form of the quotient of the heat and the temperature. Thus, the physical essence of entropy transfer is the unavailable potential energy transfer per unit environmental temperature. Entropy is a non-conserved, extensive, state quantity of a system, and entropy generation in an irreversible heat transfer process

  6. Kinetic model for torrefaction of wood chips in a pilot-scale continuous reactor

    DEFF Research Database (Denmark)

    Shang, Lei; Ahrenfeldt, Jesper; Holm, Jens Kai

    2014-01-01

    accordance with the model data. In an additional step a continuous, pilot scale reactor was built to produce torrefied wood chips in large quantities. The "two-step reaction in series" model was applied to predict the mass yield of the torrefaction reaction. Parameters used for the calculation were...... at different torrefaction temperatures, it was possible to predict the HHV of torrefied wood chips from the pilot reactor. The results from this study and the presented modeling approach can be used to predict the product quality from pilot scale torrefaction reactors based on small scale experiments and could...

  7. Remarks and suggestions concerned with formulation of the definition of quantity ''committed dose'' and quantity ''radiation burden'' useful in estimates of population exposure

    International Nuclear Information System (INIS)

    Cwik, T.

    1990-01-01

    The paper contains remarks to the definitions of the quantity ''commited dose'' given in the publications of the ICRP. The suggestions are presented on the mode of formulating the definition of the quantity ''commited dose'' and the definition of the quantity denoted hitherto by the symbol H 50 . The other suggestions deal with introduction of the quantity ''radiation burden'', assigned for use in assessments of irradiation expressed ''per caput'' of population. 9 refs. (author)

  8. Pilot process waste assessment for the fireset area

    International Nuclear Information System (INIS)

    Cole, M.J.; Goethe, M.C.

    1992-08-01

    A pilot process waste assessment (WA) was conducted in the fireset area to develop methodology for conducting future process waste assessments. The study was conducted on trichloroethylene spray cleaning using the guidance for PWAs supplied by Environment, Safety, and Health (ES ampersand H). The first objective was to draw up a flow diagram (see Appendix A, worksheet 4) for the process. When this was done, a mass balance (see Appendix A, Worksheet 5) was conducted to determine the quantity of incoming material and where it was going during the process. The mass balance showed that a large quantity of trichloroethylene and all the isopropyl alcohol was being released to the atmosphere instead of being captured in the waste solvent container. Upon completion of the mass balance, waste minimization options where identified (see Appendix A, Worksheet 8) to reduce or eliminate the quantity of hazardous solvent used

  9. Pilot Weather Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Aviation weather reports relayed from pilots to FAA air traffic controllers or National Weather Service personnel. Elements include sky cover, turbulence, wind...

  10. Agile Web Pilot Program

    National Research Council Canada - National Science Library

    Lang, Mark

    1997-01-01

    ... in an increasingly competitive global marketplace. The pilot program allowed 18 small and medium sized enterprises to experiment with new agile business practices in competitive manufacturing environments by forming virtual organizations within...

  11. CERN pilot greenhouse

    CERN Multimedia

    1983-01-01

    This pilot installation was situated near Bld. BA6 opposite to the main entrance of the Meyrin site, with respect to Route de Meyrin. See Weekly Bulletin 3/83, and also photo 8305594X, 8505898X, 8302200.

  12. Dangerous quantities of radioactive material (D-values)

    International Nuclear Information System (INIS)

    2010-01-01

    Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002). IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

  13. Solvation quantities from a COSMO-RS equation of state

    International Nuclear Information System (INIS)

    Panayiotou, C.; Tsivintzelis, I.; Aslanidou, D.; Hatzimanikatis, V.

    2015-01-01

    Highlights: • Extension of the successful COSMO-RS model to an equation-of-state model. • Two scaling constants, obtained from atom-specific contributions. • Overall estimation of the solvation quantities and contributions. - Abstract: This work focuses on the extension of the successful COSMO-RS model of mixtures into an equation-of-state model of fluids and its application for the estimation of solvation/hydration quantities of a variety of chemical substances. These quantities include free-energies, enthalpies and entropies of hydration as well as the separate contributions to each of them. Emphasis is given on the estimation of contributions from the conformational changes of solutes upon solvation and the associated restructuring of solvent in its immediate neighborhood. COSMO-RS is a quantum-mechanics based group/segment contribution model in which the Quasi-Chemical (QC) approach is used for the description of the non-random distribution of interacting segments in the system. Thus, the equation-of-state development is done through such a QC framework. The new model will not need any adjustable parameters for the strong specific interactions, such as hydrogen bonds, since they will be provided by the quantum-mechanics based cosmo-files – a key feature of COSMO-RS model. It will need, however, one volumetric and one energy parameter per fluid, which are scaling constants or molecular descriptors of the fluid and are obtained from rather easily available data such as densities, boiling points, vapor pressures, heats of vaporization or second virial coefficients. The performance and the potential of the new equation-of-state model to become a fully predictive model are critically discussed

  14. Radiation quantities, units and measurements. Final report 1999

    International Nuclear Information System (INIS)

    Wambersie, A.; Allisy, A.; Caswell, R.S.

    2000-01-01

    The determination of human exposure to radiation and radioactivity, whether arising from environmental exposures, medical practice or industrial activities, requires a fundamental set of quantities and units with which exposures can be specified and the means and ability to make measurements which yield results in terms of these quantities and units. Radiation protection then, as well as effective use of radiation in medical applications, requires the capability to accurately quantify the characteristics and extent of radiation exposure, so that appropriate and useful assessments of the potential health consequences and risks, whether for protection of the public and workers or for diagnosis and treatment of disease, can be formulated. The work carried out via this concerted action on ''Radiation quantities, units and measurements'' has addressed these needs. Measurement of radiation is a complex subject and is a science in itself. Yet many users of radiation who need to make radiation measurements cannot be expected to become experts in this particular field. They need authoritative guidance on how to deal with the measurement problems connected with their particular use of radiation. The work carried out pursuant to this concerted action has resulted in publications that meet this need. Important achievements include the publication of seven new ICRU reports, the completion of all but the printing of three other ICRU reports, completion of the drafting work on two other reports, the development of many others reports and the initiation of seven new activities that will result in ICRU reports representing important future contribution to the needs identified in this project. (orig.)

  15. Evaluating the uncertainty of input quantities in measurement models

    Science.gov (United States)

    Possolo, Antonio; Elster, Clemens

    2014-06-01

    The Guide to the Expression of Uncertainty in Measurement (GUM) gives guidance about how values and uncertainties should be assigned to the input quantities that appear in measurement models. This contribution offers a concrete proposal for how that guidance may be updated in light of the advances in the evaluation and expression of measurement uncertainty that were made in the course of the twenty years that have elapsed since the publication of the GUM, and also considering situations that the GUM does not yet contemplate. Our motivation is the ongoing conversation about a new edition of the GUM. While generally we favour a Bayesian approach to uncertainty evaluation, we also recognize the value that other approaches may bring to the problems considered here, and focus on methods for uncertainty evaluation and propagation that are widely applicable, including to cases that the GUM has not yet addressed. In addition to Bayesian methods, we discuss maximum-likelihood estimation, robust statistical methods, and measurement models where values of nominal properties play the same role that input quantities play in traditional models. We illustrate these general-purpose techniques in concrete examples, employing data sets that are realistic but that also are of conveniently small sizes. The supplementary material available online lists the R computer code that we have used to produce these examples (stacks.iop.org/Met/51/3/339/mmedia). Although we strive to stay close to clause 4 of the GUM, which addresses the evaluation of uncertainty for input quantities, we depart from it as we review the classes of measurement models that we believe are generally useful in contemporary measurement science. We also considerably expand and update the treatment that the GUM gives to Type B evaluations of uncertainty: reviewing the state-of-the-art, disciplined approach to the elicitation of expert knowledge, and its encapsulation in probability distributions that are usable in

  16. Comparison of simulated and measured quantities of a duplex reactor

    Energy Technology Data Exchange (ETDEWEB)

    Koskela, M.; Kajava, M. [ABB Marine, Helsinki (Finland)

    1997-12-31

    The purpose of this article is to illustrate the use of an analog simulator as a design tool when designing new power electric equipment. The purpose of simulation is to predict the functionality of electrical equipment to be constructed. Duplex reactor is an electromagnetic device designed to reduce voltage harmonics and short circuit currents in the ship electrical network. In this report a comparison between simulated and measured electrical quantities of a duplex reactor has been made. The purpose of the measurements was to show the correct functioning of the reactor. The simulation results and the measured waveforms corresponds well to each other. (orig.) 4 refs.

  17. Sustainable economic production quantity models for inventory systems with shortage

    DEFF Research Database (Denmark)

    Taleizadeh, Ata Allah; Soleymanfar, Vahid Reza; Govindan, Kannan

    2018-01-01

    optimal values of inventory system variables, we solve four independent profit maximization problems for four different situations. These proposed models include a basic model in which shortages are not allowed, and when shortages are allowed, the lost sale, full backordering and partial backordering...... (EPQ). The theoretical sustainable EOQ and EPQ models are basic models that ignore many real-life conditions such as the possibility of stock-out in inventory systems. In this paper, we develop four new sustainable economic production quantity models that consider different shortage situations. To find...

  18. Net present value analysis of the economic production quantity

    OpenAIRE

    Disney, Stephen Michael; Warburton, R. D. H.; Zhong, Q. C.

    2013-01-01

    Using Laplace transforms we extend the economic production quantity (EPQ) model by analysing cash flows from a net present value (NPV) viewpoint. We obtain an exact expression for the present value of the cash flows in the EPQ problem. From this, we are able to derive the optimal batch size. We obtain insights into the monotonicity and convexity of the present value of each of the cash flows, and show that there is a unique minimum in the present value of the sum of the cash flows in the exte...

  19. Ultracold atoms for precision measurement of fundamental physical quantities

    CERN Multimedia

    CERN. Geneva

    2003-01-01

    Cooling and trapping of neutral atoms has been one of the most active fields of research in physics in recent years. Several methods were demonstrated to reach temperatures as low as a few nanokelvin allowing, for example, the investigation of quantum degenerate gases. The ability to control the quantum degrees of freedom of atoms opens the way to applications for precision measurement of fundamental physical quantities. Experiments in progress, planned or being considered using new quantum devices based on ultracold atoms, namely atom interferometers and atomic clocks, will be discussed.

  20. Physical quantities related to measurement campaigns for cooling towers

    International Nuclear Information System (INIS)

    Boegel, W.

    1975-12-01

    The nomenclature in reports on the measurement campaigns for cooling towers will be adapted as far as possible to the already existing VDI report on this subject. On the other hand, the appropriate standards will also be accounted for. In order to facilitate a decision in individual cases in a first table the meteorologically or generally interesting quantities of the VDI reports are compared with the German, international, and WMO standards and - if necessary - also commented. A second table contains the air humidity parameters standardized by WMO including brief definitions. (orig/HP) [de

  1. MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

    Directory of Open Access Journals (Sweden)

    O. N. Korinovskaya

    2014-08-01

    Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the

  2. Documentation and analysis for packaging limited quantity ice chests

    International Nuclear Information System (INIS)

    Nguyen, P.M.

    1995-01-01

    The purpose of this Documentation and Analysis for Packaging (DAP) is to document that ice chests meet the intent of the International Air Transport Association (IATA) and the U.S. Department of Transportation (DOT) Code of Federal Regulations as strong, tight containers for the packaging of limited quantities for transport. This DAP also outlines the packaging method used to protect the sample bottles from breakage. Because the ice chests meet the DOT requirements, they can be used to ship LTD QTY on the Hanford Site

  3. Investigation on Capability of Reaming Process using Minimal Quantity Lubrication

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo; Tosello, Guido; Piska, Miroslav

    2008-01-01

    An investigation on reaming using minimal quantity lubrication (MQL) was carried out with the scope of documenting process capability using a metrological approach. Reaming tests were carried out on austenitic stainless steel, using HSS reamers with different cutting data and lubrication conditions...... depth of cut was employed. The suitability of MQL for reaming was proven under the investigated process conditions, concerning both the quality of the machined holes, in terms of geometrical characteristics and surface finishing, and the process quality, with respect to reaming torque and thrust, along...

  4. A statistical law in the perception of risks and physical quantities in traffic

    DEFF Research Database (Denmark)

    Elvik, Rune

    2015-01-01

    This paper suggests that a universal psychophysical law influences the perception of risks and physical quantities in traffic. This law states that there will be a tendency to overestimate low probabilities or small quantities, while high probabilities or large quantities may be underestimated....... Studies of the perception of risk and physical quantities in traffic have found a highly consistent pattern....

  5. Discussion on concepts for radiological dosimetric quantities in the Japan Health Physics Society

    International Nuclear Information System (INIS)

    Takahashi, Fumiaki; Oda, Keiji

    2007-01-01

    Many dosimetric quantities have been used for radiation protection purpose. The International Commission on Radiological Protection (ICRP) has recommended protection quantities and the International Commission on Radiation Units and Measurements (ICRU) has introduced operational quantities to provide a reasonable estimate of the protection quantities. Enthusiastic discussions are continuously made on the issues of the dosimetric quantities, such as basic biological data for the definition of these quantities and applicability of the quantities to actual radiation protection practice. At the moment, some changes are being proposed concerning dosimetric quantities in the draft recommendations of ICRP, opened for consultation in recent years. Thus, the Japan Health Physics Society (JHPS) established the Expert Committee on concepts of Dosimetric Quantities used in radiological protection (ECDQ) in April 2005 to reviewed and discuss issues in the dosimetric quantities. (author)

  6. Determination of dosimetric quantities in pediatric abdominal computed tomography scans

    Energy Technology Data Exchange (ETDEWEB)

    Jornada, Tiago da Silva [Universidade Federal de Sao Paulo (UNIFESP), Sao Paulo, SP (Brazil). Escola Paulista de Medicina. Dept. de Diagnostipo por Imagem; Silva, Teogenes Augusto da, E-mail: silvata@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2014-09-15

    Objective: aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods: the study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results: No significant difference was observed in the values for weighted air kerma index (C{sub W}), but the differences were relevant in values for volumetric air kerma index (C{sub VOL}), air kerma-length product (P{sub KL,CT}) and effective dose. Conclusion: Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, P{sub KL,CT} and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. (author)

  7. Inventory simulation tools: Separating nuclide contributions to radiological quantities

    Science.gov (United States)

    Gilbert, Mark R.; Fleming, Michael; Sublet, Jean-Christophe

    2017-09-01

    The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel) activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results - most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA) spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal - standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots. Note to the reader: the pdf file has been changed on September 22, 2017.

  8. Inventory simulation tools: Separating nuclide contributions to radiological quantities

    Directory of Open Access Journals (Sweden)

    Gilbert Mark R.

    2017-01-01

    Full Text Available The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results – most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal – standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots.

  9. Peer Assessment for Construction Management and Quantity Surveying Students

    Directory of Open Access Journals (Sweden)

    Patricia McLaughlin

    2012-11-01

    Full Text Available Students undertaking the Bachelor of ConstructionManagement degree course at RMIT University, Melbourne,qualify for registration with the Australian Institute ofQuantity Surveyors (AIQS and the Australian Institute ofBuilding (AIB upon graduation. Over the past decade thedegree course has been constantly upgraded and altered inline with recommendations from professional bodies such asthese and other industry partners. In 1994 the Departmentof Building and Construction Economics re-assesseda range of subjects including the first year technologysubjects. Out of the review a problem-based integratedlearning unit was developed and tested. This unit has nowbeen in place for ten years.Quantity surveying and construction management likemost other professions in the construction industryrequire teamwork and advanced consultation skills. Theseskills may be learnt through experience but there isconsiderable evidence that these skills can be taught in theundergraduate years. Therefore in line with team-basedapproaches used in industry and professional constructionsettings, this year a new assessment model - peerassessment - will be applied to the problem-based learningunit. This paper describes the procedures and processesused to introduce the change and examines the theoreticalbase upon which the model was developed.

  10. Determination of dosimetric quantities in pediatric abdominal computed tomography scans*

    Science.gov (United States)

    Jornada, Tiago da Silva; da Silva, Teógenes Augusto

    2014-01-01

    Objective Aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods The study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results No significant difference was observed in the values for weighted air kerma index (CW), but the differences were relevant in values for volumetric air kerma index (CVOL), air kerma-length product (PKL,CT) and effective dose. Conclusion Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, PKL,CT and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. PMID:25741103

  11. Determinants of procurement strategy for construction works: quantity surveyors’ perspectives

    Directory of Open Access Journals (Sweden)

    Olanrewaju AbdulLateef

    2016-01-01

    Full Text Available The selection of the ‘appropriate’ procurement strategy is a prerequisite to the success or failure of a construction project. This paper investigates the factors determining the selection of appropriate procurement strategy for construction works in Nigeria. Data for the study was collected through an online survey questionnaire. The survey administration involves only quantity surveyors. Quantity surveyors were targeted because they advise clients and other stakeholders on procurement and contractual issues on construction works. A total of 33 usable responses were received and analysed for this study. On the basis of the results, it is concluded that the selection of procurement strategies for construction depend on complex interrelated factors. The study could not detect a particular factor or few factors responsible for a procurement strategy selection. The findings of this study is useful because it argues that the construction sector needs to broaden its considerations on the procurement strategy’s determinants rather than focusing solely on the client’s type and nature of projects as is often cited. Future research could segment these factors in terms of class of construction works or increase the sample size, which might lead to different findings.

  12. Estimation of Waste Quantities Using DeCAT-Pro

    Energy Technology Data Exchange (ETDEWEB)

    Yun, Taesik; Jung, Hyejin; Oh, Jaeyoung; Kim, Younggook [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    The D and D (Dismantling and Decontamination) is scheduled to get started in June 2022 elapsing five years of cooling spent fuels down. The final site status is postulated as Brown Field and tentative DCGL of less than 0.1 mSv per year to evaluate waste quantities in a conservative manner. The decommissioning strategy was determined the immediate decommissioning whose whole period would be taken for approximately 15 years; pre-decommissioning for two years, spent fuel cool-down for five years, D and D for six years, site remediation for two years. The assumption to dismantle the underground facilities including SSCs is to one meter beneath the ground level and the other facilities remain intact. In addition, non-radioactive concrete wastes would be used to landfill gaps of the remaining facilities. Although there are many assumptions we applied, the methodologies developed and the data produced by this research will play a meaningful role as a good starting point for the Kori-1 decommissioning after its shutdown to logically and reasonably estimate the waste quantity. However it is clear that tenacious efforts should be taken to successfully perform the decommissioning project.

  13. The orientation distribution of tunneling-related quantities

    Science.gov (United States)

    Seif, W. M.; Refaie, A. I.; Botros, M. M.

    2018-03-01

    In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

  14. Highway route controlled quantity shipment routing reports - An overview

    International Nuclear Information System (INIS)

    Cashwell, J.W.; Welles, B.W.; Welch, M.J.

    1989-01-01

    US Department of Transportation (DOT) regulations require a postnotification report from the shipper for all shipments of radioactive materials categorized as a Highway Route Controlled Quantity. These postnotification reports, filed in compliance with 49 CFR 172.203(d), have been compiled by the DOT in a database known as the Radioactive Materials Routing Report (RAMRT) since 1982. The data were sorted by each of its elements to establish historical records and trends of Highway Route Controlled Quantity shipments from 1982 through 1987. Approximately 1520 records in the RAMRT database were compiled for this analysis. Approximately half of the shipments reported for the study period were from the US Department of Energy (DOE) and its contractors, with the others being commercial movements. Two DOE installations, EG and G Idaho and Oak Ridge, accounted for nearly half of the DOE activities. Similarly, almost half of the commercial movements were reported by two vendors, Nuclear Assurance Corporation and Transnuclear, Incorporated. Spent fuel from power and research reactors accounted for approximately half of all shipments

  15. DME Prosthetics Orthotics, and Supplies Fee Schedule

    Data.gov (United States)

    U.S. Department of Health & Human Services — Durable Medical Equipment, Prosthetics-Orthotics, and Supplies Fee Schedule. The list contains the fee schedule amounts, floors, and ceilings for all procedure codes...

  16. DIRAC universal pilots

    Science.gov (United States)

    Stagni, F.; McNab, A.; Luzzi, C.; Krzemien, W.; Consortium, DIRAC

    2017-10-01

    In the last few years, new types of computing models, such as IAAS (Infrastructure as a Service) and IAAC (Infrastructure as a Client), gained popularity. New resources may come as part of pledged resources, while others are in the form of opportunistic ones. Most but not all of these new infrastructures are based on virtualization techniques. In addition, some of them, present opportunities for multi-processor computing slots to the users. Virtual Organizations are therefore facing heterogeneity of the available resources and the use of an Interware software like DIRAC to provide the transparent, uniform interface has become essential. The transparent access to the underlying resources is realized by implementing the pilot model. DIRAC’s newest generation of generic pilots (the so-called Pilots 2.0) are the “pilots for all the skies”, and have been successfully released in production more than a year ago. They use a plugin mechanism that makes them easily adaptable. Pilots 2.0 have been used for fetching and running jobs on every type of resource, being it a Worker Node (WN) behind a CREAM/ARC/HTCondor/DIRAC Computing element, a Virtual Machine running on IaaC infrastructures like Vac or BOINC, on IaaS cloud resources managed by Vcycle, the LHCb High Level Trigger farm nodes, and any type of opportunistic computing resource. Make a machine a “Pilot Machine”, and all diversities between them will disappear. This contribution describes how pilots are made suitable for different resources, and the recent steps taken towards a fully unified framework, including monitoring. Also, the cases of multi-processor computing slots either on real or virtual machines, with the whole node or a partition of it, is discussed.

  17. PULSE Pilot Certification Results

    Directory of Open Access Journals (Sweden)

    Pamela Pape-Lindstrom

    2015-08-01

    Full Text Available The pilot certification process is an ambitious, nationwide endeavor designed to motivate important changes in life sciences education that are in line with the recommendations of the 2011 Vision and Change Report: A Call to Action (American Association for the Advancement of Science [AAAS], 2011.  It is the goal of the certification process to acknowledge departments that have progressed towards full implementation of the tenets of Vision and Change and to motivate departments that have not begun to adopt the recommendations to consider doing so.  More than 70 life science departments applied to be part of the pilot certification process, funded by a National Science Foundation grant, and eight were selected based on initial evidence of transformed and innovative educational practices.  The programs chosen represent a wide variety of schools, including two-year colleges, liberal-arts institutions, regional comprehensive colleges, research universities and minority serving institutions.  Outcomes from this pilot were released June 1, 2015 (www.pulsecommunity.org, with all eight programs being recognized as having progressed along a continuum of change.  Five levels of achievement were defined as PULSE Pilot Progression Levels.  Of the eight departments in the pilot, one achieved “PULSE Progression Level III: Accomplished”.  Six departments achieved “PULSE Progression Level II: Developing” and one pilot department achieved “PULSE Progression Level I: Beginning”.  All of the schools have made significant movement towards the recommendations of Vision and Change relative to a traditional life sciences curriculum.  Overall, the response from the eight pilot schools has been positive. 

  18. MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

    Directory of Open Access Journals (Sweden)

    Korinovskaya Olga Nikolaevna

    2014-08-01

    Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the

  19. Linking the Pilot Structural Model and Pilot Workload

    Science.gov (United States)

    Bachelder, Edward; Hess, Ronald; Aponso, Bimal; Godfroy-Cooper, Martine

    2018-01-01

    Behavioral models are developed that closely reproduced pulsive control response of two pilots using markedly different control techniques while conducting a tracking task. An intriguing find was that the pilots appeared to: 1) produce a continuous, internally-generated stick signal that they integrated in time; 2) integrate the actual stick position; and 3) compare the two integrations to either issue or cease a pulse command. This suggests that the pilots utilized kinesthetic feedback in order to sense and integrate stick position, supporting the hypothesis that pilots can access and employ the proprioceptive inner feedback loop proposed by Hess's pilot Structural Model. A Pilot Cost Index was developed, whose elements include estimated workload, performance, and the degree to which the pilot employs kinesthetic feedback. Preliminary results suggest that a pilot's operating point (parameter values) may be based on control style and index minimization.

  20. 76 FR 54095 - Pilot in Command Proficiency Check and Other Changes to the Pilot and Pilot School Certification...

    Science.gov (United States)

    2011-08-31

    ... [Docket No.: FAA-2008-0938; Amendment Nos. 61-128, 91-324, 141-15, and 142-7] RIN 2120-AJ18 Pilot in Command Proficiency Check and Other Changes to the Pilot and Pilot School Certification Rules AGENCY... regulations concerning pilot, flight instructor, and pilot school certification. This rule will require pilot...

  1. The quantity time relation in the ionizing radiations

    Science.gov (United States)

    Jordão, B. O.; Quaresma, D. S.; Peixoto, J. G. P.

    2018-03-01

    The metrology area has taken a step forward with regard to the uncertainty calculation. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (i) the development and calibration of a microcontrolled time device with a resolution of 1x10-4 s, in order to characterize the time greatness and make it re-producible; (ii) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (iii) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate.

  2. Quantity and structure of word knowledge across adulthood.

    Science.gov (United States)

    Salthouse, Timothy A

    2014-09-01

    Cross-sectional and longitudinal data from moderately large samples of healthy adults confirmed prior findings of age-related declines in measures of the quantity of word knowledge beginning around age 65. Additional analyses were carried out to investigate the interrelations of different types of vocabulary knowledge at various periods in adulthood. Although the organizational structures were similar in adults of different ages, scores on tests with different formats had weaker relations to a higher-order vocabulary construct beginning when adults were in their 60's. The within-person dispersion among different vocabulary test scores was also greater after about 65 years of age. The discovery of quantitative decreases in amount of knowledge occurring at about the same age as qualitative shifts in the structure of knowledge raises the possibility that the two types of changes may be causally linked.

  3. Synthesis of pure iron magnetic nanoparticles in large quantity

    International Nuclear Information System (INIS)

    Tiwary, C S; Kashyap, S; Chattopadhyay, K; Biswas, K

    2013-01-01

    Free nanoparticles of iron (Fe) and their colloids with high saturation magnetization are in demand for medical and microfluidic applications. However, the oxide layer that forms during processing has made such synthesis a formidable challenge. Lowering the synthesis temperature decreases rate of oxidation and hence provides a new way of producing pure metallic nanoparticles prone to oxidation in bulk amount (large quantity). In this paper we have proposed a methodology that is designed with the knowledge of thermodynamic imperatives of oxidation to obtain almost oxygen-free iron nanoparticles, with or without any organic capping by controlled milling at low temperatures in a specially designed high-energy ball mill with the possibility of bulk production. The particles can be ultrasonicated to produce colloids and can be bio-capped to produce transparent solution. The magnetic properties of these nanoparticles confirm their superiority for possible biomedical and other applications. (paper)

  4. Protection of groundwater resources quality and quantity in mining areas

    International Nuclear Information System (INIS)

    Grmela, A.

    1997-01-01

    This contribution is devoted to the problems of the impact of land subsidence from coal and other mining systems on underground and surface waters, particularly in relation to the possible influence on quality and quantity of pumped waters for public or individual supply. It determines features of permanent and time-limited changes of hydrogeological structure and effectiveness of measures for their minimization (classification of sources from the point of view of protection, delineation of protection zones for water resources, monitoring of effectiveness of measures). Case studies are presented for examples from the Czech part of Upper Silesian Basin - catchment area Doubrava-Spluchov, Karvina-Stare Mesto, Ostrava-Nove Ves, and Dubi, Darkov Spa. Attention is focused on problems of delimitation of protection zones in undermined areas in respect to the new proposal of the Appendix to Water Law. 8 refs., 2 figs

  5. Bulky waste quantities and treatment methods in Denmark

    DEFF Research Database (Denmark)

    Larsen, Anna Warberg; Petersen, Claus; Christensen, Thomas Højlund

    2012-01-01

    were identified of which ten were recyclable and constituted 50–60% of the total quantity. The others were combustible waste for incineration (30–40%) and non-combustible waste for landfilling (10%). The largest fractions by mass were combustible waste, bricks and tile, concrete, non-combustible waste....... In addition a sorting analysis was conducted on combustible waste, which is a major fraction of bulky waste in Denmark. The generation of bulky waste was found to be 150–250 kg capita−1 year−1, and 90% of the waste was collected at recycling centres; the rest through kerbside collection. Twelve main fractions......, wood, and metal scrap, which together made up more than 90% of the total waste amounts. The amount of combustible waste could be significantly reduced through better sorting. Many of the waste fractions consisted of composite products that underwent thorough separation before being recycled...

  6. Symbol addition by monkeys provides evidence for normalized quantity coding

    Science.gov (United States)

    Livingstone, Margaret S.; Pettine, Warren W.; Srihasam, Krishna; Moore, Brandon; Morocz, Istvan A.; Lee, Daeyeol

    2014-01-01

    Weber’s law can be explained either by a compressive scaling of sensory response with stimulus magnitude or by a proportional scaling of response variability. These two mechanisms can be distinguished by asking how quantities are added or subtracted. We trained Rhesus monkeys to associate 26 distinct symbols with 0–25 drops of reward, and then tested how they combine, or add, symbolically represented reward magnitude. We found that they could combine symbolically represented magnitudes, and they transferred this ability to a novel symbol set, indicating that they were performing a calculation, not just memorizing the value of each combination. The way they combined pairs of symbols indicated neither a linear nor a compressed scale, but rather a dynamically shifting, relative scaling. PMID:24753600

  7. ANALYZER OF QUANTITY AND QUALITY OF THE ELECTRIC POWER

    Directory of Open Access Journals (Sweden)

    A. I. Semilyak

    2013-01-01

    Full Text Available One of the activities of the research center for “Energy Saving Technologies and Smart Metering in Electrical Power Engineering" is research work on the use of electronic devices and systems of intelligent power distribution, produced by Analog Devices and equipped with the accurate energy consumption measurement feature. The article focuses on the development of the analyzer of quantity and quality of electric energy.The main part of the analyzer is a metering IC by Analog Devices ADE7878, designed for use in commercial and industrial smart electricity meters. Such counters measure the amount of consumed or produced electric energy with high accuracy and have the means of remote meter reading.

  8. The quantity time relation in the ionizing radiations

    Energy Technology Data Exchange (ETDEWEB)

    Jordão, Bruno; Quaresma, Daniel, E-mail: bjordan@on.br [Observatorio Nacional (LPTF/ON), Rio de Janeiro, RJ (Brazil). Laboratório Primário de Tempo e Frequência; Peixoto, José Guilherme P. [Instituto de Radioproteção e Dosimetria (LNMRI/IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Laboratório Nacional de Metrologia das Radiações Ionizantes

    2017-07-01

    The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10{sup -4} s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

  9. The quantity time relation in the ionizing radiations

    International Nuclear Information System (INIS)

    Jordão, Bruno; Quaresma, Daniel; Peixoto, José Guilherme P.

    2017-01-01

    The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10 -4 s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

  10. Measuring Radionuclides in the environment: radiological quantities and sampling designs

    International Nuclear Information System (INIS)

    Voigt, G.

    1998-10-01

    One aim of the workshop was to support and provide an ICRU report committee (International Union of Radiation Units) with actual information on techniques, data and knowledge of modern radioecology when radionuclides are to be measured in the environment. It has been increasingly recognised that some studies in radioecology, especially those involving both field sampling and laboratory measurements, have not paid adequate attention to the problem of obtaining representative, unbiased samples. This can greatly affect the quality of scientific interpretation, and the ability to manage the environment. Further, as the discipline of radioecology has developed, it has seen a growth in the numbers of quantities and units used, some of which are ill-defined and which are non-standardised. (orig.)

  11. NSTAR Smart Grid Pilot

    Energy Technology Data Exchange (ETDEWEB)

    Rabari, Anil [NSTAR Electric, Manchester, NH (United States); Fadipe, Oloruntomi [NSTAR Electric, Manchester, NH (United States)

    2014-03-31

    NSTAR Electric & Gas Corporation (“the Company”, or “NSTAR”) developed and implemented a Smart Grid pilot program beginning in 2010 to demonstrate the viability of leveraging existing automated meter reading (“AMR”) deployments to provide much of the Smart Grid functionality of advanced metering infrastructure (“AMI”), but without the large capital investment that AMI rollouts typically entail. In particular, a central objective of the Smart Energy Pilot was to enable residential dynamic pricing (time-of-use “TOU” and critical peak rates and rebates) and two-way direct load control (“DLC”) by continually capturing AMR meter data transmissions and communicating through customer-sited broadband connections in conjunction with a standardsbased home area network (“HAN”). The pilot was supported by the U.S. Department of Energy’s (“DOE”) through the Smart Grid Demonstration program. NSTAR was very pleased to not only receive the funding support from DOE, but the guidance and support of the DOE throughout the pilot. NSTAR is also pleased to report to the DOE that it was able to execute and deliver a successful pilot on time and on budget. NSTAR looks for future opportunities to work with the DOE and others in future smart grid projects.

  12. Effects of insemination quantity on honey bee queen physiology.

    Directory of Open Access Journals (Sweden)

    Freddie-Jeanne Richard

    2007-10-01

    Full Text Available Mating has profound effects on the physiology and behavior of female insects, and in honey bee (Apis mellifera queens, these changes are permanent. Queens mate with multiple males during a brief period in their early adult lives, and shortly thereafter they initiate egg-laying. Furthermore, the pheromone profiles of mated queens differ from those of virgins, and these pheromones regulate many different aspects of worker behavior and colony organization. While it is clear that mating causes dramatic changes in queens, it is unclear if mating number has more subtle effects on queen physiology or queen-worker interactions; indeed, the effect of multiple matings on female insect physiology has not been broadly addressed. Because it is not possible to control the natural mating behavior of queens, we used instrumental insemination and compared queens inseminated with semen from either a single drone (single-drone inseminated, or SDI or 10 drones (multi-drone inseminated, or MDI. We used observation hives to monitor attraction of workers to SDI or MDI queens in colonies, and cage studies to monitor the attraction of workers to virgin, SDI, and MDI queen mandibular gland extracts (the main source of queen pheromone. The chemical profiles of the mandibular glands of virgin, SDI, and MDI queens were characterized using GC-MS. Finally, we measured brain expression levels in SDI and MDI queens of a gene associated with phototaxis in worker honey bees (Amfor. Here, we demonstrate for the first time that insemination quantity significantly affects mandibular gland chemical profiles, queen-worker interactions, and brain gene expression. Further research will be necessary to elucidate the mechanistic bases for these effects: insemination volume, sperm and seminal protein quantity, and genetic diversity of the sperm may all be important factors contributing to this profound change in honey bee queen physiology, queen behavior, and social interactions in the

  13. Biologically Weighted Quantities in Radiotherapy: an EMRP Joint Research Project

    Directory of Open Access Journals (Sweden)

    Rabus Hans

    2014-01-01

    Full Text Available Funded within the European Metrology Research Programme (EMRP [1], the joint research project “Biologically weighted quantities in radiotherapy” (BioQuaRT [2] aims to develop measurement and simulation techniques for determining the physical properties of ionising particle tracks on different length scales (about 2 nm to 10 μm, and to investigate the correlation of these track structure characteristics with the biological effects of radiation at the cellular level. Work package 1 develops micro-calorimeter prototypes for the direct measurement of lineal energy and will characterise their response for different ion beams by experiment and modelling. Work package 2 develops techniques to measure particle track structure on different length scales in the nanometre range as well as a measurement device integrating a silicon microdosimeter and a nanodosimeter. Work package 3 investigates the indirect effects of radiation based on probes for quantifying particular radical and reactive oxygen species (ROS. Work package 4 focuses on the biological aspects of radiation damage and will produce data on initial DNA damage and late effects for radiotherapy beams of different qualities. Work package 5 provides evaluated data sets of DNA cross-sections and develops a multi-scale model to address microscopic and nanometric track structure properties. The project consortium includes three linked researchers holding so-called Researcher Excellence Grants, who carry out ancillary investigations such as developing and benchmarking a new biophysical model for induction of early radiation damage and developing methods for the translation of quantities derived from particle track structure to clinical applications in ion beam therapy.

  14. Is the dose equivalent index a quantity to be measured

    International Nuclear Information System (INIS)

    Wagner, S.R.

    1980-01-01

    ICRP introduced the concept of Effective Dose Equivalent H(sub)E and fixed the basic limits of radiation exposure in terms of H(sub)I. As H(sub)E cannot be measured, ICRP stated that with external exposure to penetrating radiation the limitation of the Dose Equivalent Index H(sub)I would afford at least as good a level of protection. However, difficulties arise in measuring H(sub)I and in calibrating instruments in terms of H(sub)I, since the height and location of the dose equivalent maximum in the sphere which is the phantom used in the definition of H(sub)I, depend on the energy and the angular distribution of the incident radiation. That is, H(sub)I is not an additive quantity relative to the partial H(sub)I(sub)i-values of the different energy and angular components. Hence, 1) the distribution of dose equivalent in the sphere must be measured in full for a determination of H(sub)I, and 2) it is not possible to calibrate an instrument which does not exhibit the scattering and absorption properties of the sphere, consistently for arbitrary radiation fields in terms of H(sub)I. Thus the calibration in an unidirectional beam would infer an uncertainty which may amount to a factor of up to 4. This would hardly be tolerable as a base for radiation protection provisions. An alternative is to introduce operational quantities which are additive, e.g. 1) the sum of maxima of the dose equivalent distributions in the sphere produced by different radiation components, and 2) the mean dose equivalent in the sphere. Their relation to H(sub)E for different types of radiation and consequences on secondary limits are discussed. (H.K.)

  15. Gender Differences in Output Quality and Quantity under Competition and Time Constraints: Evidence from a Pilot Study

    OpenAIRE

    Olga Shurchkov

    2009-01-01

    Gender gaps in income and level of position in the workplace are widespread. One explanation for this inequality is that the genders perform differently under competitive conditions, as previous experimental studies have found a significant gender gap in competitive tasks that are perceived to favor men. In this paper, we use a verbal task that is perceived to favor women and find no gender difference under competition per se. We also reject the hypothesis that a .stereotype threat. explains ...

  16. Mobile loading transuranic waste at small quantity sites in the Department of Energy complex-10523

    International Nuclear Information System (INIS)

    Carter, Mitch; Howard, Bryan; Weyerman, Wade; Mctaggart, Jerri

    2009-01-01

    Los Alamos National Laboratory, Carlsbad Office (LANL-CO), operates mobile loading operations for all of the large and small quantity transuranic (TRU) waste sites in the Department of Energy (DOE) complex. The mobile loading team performs loading and unloading evolutions for both contact handled (CH) and remote handled (RH) waste. For small quantity sites, many of which have yet to remove their TRU waste, the mobile loading team will load shipments that will ship to Idaho National Laboratory, a centralization site, or ship directly to the Waste Isolation Pilot Plant (WIPP). For example, Argonne National Laboratory and General Electric Vallecitos Nuclear Center have certified programs for RH waste so they will ship their RH waste directly to WIPP. Many of the other sites will ship their waste to Idaho for characterization and certification. The Mobile Loading Units (MLU) contain all of the necessary equipment needed to load CH and RH waste into the appropriate shipping vessels. Sites are required to provide additional equipment, such as cranes, fork trucks, and office space. The sites are also required to provide personnel to assist in the shipping operations. Each site requires a site visit from the mobile loading team to ensure that all of the necessary site equipment, site requirements and space for shipping can be provided. The mobile loading team works diligently with site representatives to ensure that all safety and regulatory requirements are met. Once the waste is ready and shipping needs are met, the mobile loading team can be scheduled to ship the waste. The CH MLU is designed to support TRUPACT-II and HalfPACT loading activities wherever needed within the DOE complex. The team that performs the mobile loading operation has obtained national certification under DOE for TRUPACT-II and HalfPACT loading and shipment certification. The RH MLU is designed to support removable lid canister (RLC) and RH-72B cask loading activities wherever needed within the DOE

  17. User Participation in Pilot Implementation

    DEFF Research Database (Denmark)

    Torkilsheyggi, Arnvør Martinsdóttir á; Hertzum, Morten

    2014-01-01

    Pilot implementations provide users with real-work experiences of how a system will affect their daily work before the design of the system is finalized. On the basis of a pilot implementation of a system for coordinating the transport of patients by hospital porters, we investigate pilot...... implementation as a method for participatory design. We find that to foster participation and learning about user needs a pilot implementation must create a space for reflecting on use, in addition to the space for using the pilot system. The space for reflection must also exist during the activities preparing...... the use of the pilot system because the porters and nurses learned about their needs throughout the pilot implementation, not just during use. Finally, we discuss how the scope and duration of a pilot implementation influence the conditions for participation....

  18. Pilot unit for cesium-137 separation

    International Nuclear Information System (INIS)

    Raggenbass, A.; Quesney, M.; Fradin, J.; Dufrene, J.

    1958-01-01

    Users of radiation are becoming increasingly interested in cesium-137. At the same time the starting up of the industrial plant at Marcoule will make available in the near future large stocks of fission products which should be made use of as quickly as possible. The installation described is a pilot plant for cesium-137 production which should make it possible: - to verify the chemical method on actual solutions of fission products, by treating about 100 curies of 137 Cs by operation, - to obtain technical information on the chemical equipment (tele-commands, corrosion, maintenance, etc...), - to obtain 137 Cs in sufficient quantity to perfect the technique of the manufacture of sealed sources. (author) [fr

  19. Standardization and assessment of cell culture media quantities in roller poly ethylene terephthalate bottles employed in the industrial rabies viral vaccine production.

    Science.gov (United States)

    Jagannathan, S; Chaansha, S; Rajesh, K; Santhiya, T; Charles, C; Venkataramana, K N

    2009-09-15

    Vero cells are utilized for production of rabies vaccine. This study deals with the optimize quantity media require for the rabies vaccine production in the smooth roller surface. The rabies virus (Pasteur vaccine strain) is infected to monolayer of the various experimented bottles. To analyze the optimal quantity of media for the production of rabies viral harvest during the process of Vero cell derived rabies vaccine. The trials are started from 200 to 400 mL (PTARV-1, PTARV-2, PTARV-3, PTARV-4 and PTARV-5). The samples are taken in an appropriate time intervals for analysis of In Process Quality Control (IPQC) tests. The collected viral harvests are further processed to rabies vaccine in a pilot level and in addition to scale up an industrial level. Based on the evaluation the PTARV-2 (250 mL) show highly encouraging results for the Vero cell derived rabies vaccine production.

  20. 14 CFR 61.73 - Military pilots or former military pilots: Special rules.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Military pilots or former military pilots... Ratings and Pilot Authorizations § 61.73 Military pilots or former military pilots: Special rules. (a... a disciplinary action involving aircraft operations, a U.S. military pilot or former military pilot...

  1. Pilot project as enabler?

    DEFF Research Database (Denmark)

    Neisig, Margit; Glimø, Helle; Holm, Catrine Granzow

    This article deals with a systemic perspective on transition. The field of study addressed is a pilot project as enabler of transition in a highly complex polycentric context. From a Luhmannian systemic approach, a framework is created to understand and address barriers of change occurred using...... pilot projects as enabler of transition. Aspects of how to create trust and deal with distrust during a transition are addressed. The transition in focus is the concept of New Public Management and how it is applied in the management of the Employment Service in Denmark. The transition regards...

  2. Single-Pilot Workload Management

    Science.gov (United States)

    Rogers, Jason; Williams, Kevin; Hackworth, Carla; Burian, Barbara; Pruchnicki, Shawn; Christopher, Bonny; Drechsler, Gena; Silverman, Evan; Runnels, Barry; Mead, Andy

    2013-01-01

    Integrated glass cockpit systems place a heavy cognitive load on pilots (Burian Dismukes, 2007). Researchers from the NASA Ames Flight Cognition Lab and the FAA Flight Deck Human Factors Lab examined task and workload management by single pilots. This poster describes pilot performance regarding programming a reroute while at cruise and meeting a waypoint crossing restriction on the initial descent.

  3. Pilot pulsar surveys with LOFAR

    NARCIS (Netherlands)

    Coenen, T.

    2013-01-01

    We are performing two complementary pilot pulsar surveys as part of LOFAR commissioning. The LOFAR Pilot Pulsar Survey (LPPS) is a shallow all-sky survey using an incoherent combination of LOFAR stations. The LOFAR Tied-Array Survey (LOTAS) is a deeper pilot survey using 19 simultaneous tied-array

  4. Safeguards Implementation Guide for States with Small Quantities Protocols

    International Nuclear Information System (INIS)

    2013-01-01

    The International Atomic Energy Agency (IAEA) works to enhance the contribution of nuclear energy for peace and prosperity around the world, while helping to ensure that nuclear material is not diverted to nuclear weapons or other nuclear explosive devices. In implementing safeguards, the IAEA plays an instrumental independent verification role, providing credible assurances that States' safeguards commitments are being respected. Most of the world's non-nuclear-weapon States (NNWSs) have concluded comprehensive safeguards agreements (CSAs) with the IAEA, pursuant to the Treaty on the Non- Proliferation of Nuclear Weapons (NPT). The IAEA and States are required to cooperate in the implementation of such agreements. Effective cooperation demonstrates a State's commitment to the peaceful use of nuclear energy and furthers the State's national interests by reducing the risk of unauthorized use of nuclear material. Over 100 NNWSs party to the NPT have very limited quantities of nuclear material and have concluded protocols to their CSAs which hold in abeyance many procedures in Part II of a CSA. These protocols are referred to as 'small quantities protocols' or 'SQPs' and remain in effect as long as the State meets certain eligibility criteria. The purpose of an SQP is to reduce the burden of safeguards implementation for States with little or no nuclear activities, while retaining the integrity of the safeguards system. States with SQPs have very important obligations they must fulfil under their CSAs. In 1997, as part of the IAEA's efforts to strengthen its safeguards system, the Model Additional Protocol to the Agreement(s) between State(s) and the International Atomic Energy Agency for the Application of Safeguards was developed to provide the IAEA with broader access to information and locations, thus significantly increasing the IAEA's ability to provide assurance of the absence of undeclared nuclear material and activities in States. Many States with SQPs have

  5. Numerical and Experimental Study on the Combustion and Emission Characteristics of a Dimethyl Ether (DME Fueled Compression Ignition Engine Études numériques et expérimentales sur les caractéristiques de combustion et d’émissions d’un éther diméthylique (EDM- moteur à auto-allumage rempli de combustible

    Directory of Open Access Journals (Sweden)

    Kim Hyung Jun

    2012-05-01

    Full Text Available A numerical investigation was carried out to study on the combustion and emission characteristics of dimethyl ether (DME with wide ranges of injection timings in compression ignition engines. In order to simulate DME combustion processes, a KIVA-3V code coupled with a chemistry solver was used to solve the detailed chemical kinetics model of DME oxidation. In addition, the Kelvin-Helmholtz-Rayleigh-Taylor (KH-RT hybrid breakup model and Renormalization Group (RNG k-ε  models were applied to analyze the spray characteristics and turbulent flow, respectively. To predict the NOx formation during DME combustion, a reduced Gas Research Institute (GRI NO mechanism was used. From these results on the combustion and emission, the calculated results were compared with experimental ones for the same operating conditions. In the combustion characteristics, the calculated combustion pressure and heat release rates agreed well with experimental results. The levels of experimental NOx emissions was reduced as the start of the injection timing retarded, and also these trends appeared in calculated emission characteristics. Additionally, the calculated CO and HC emissions show an increasing trend as the start of the injection is retarded. Dans cette étude, nous considérons la simulation de la combustion du dimethyl ether (DME dans un moteur à allumage par compression. Les caractéristiques de la combustion ainsi que les émissions polluantes sont analysées sur une large gamme d’avance à l’injection. Afin de simuler le processus de combustion du EDM, le code KIVA-3V couplé à un solveur chimique a été utilisé pour résoudre la cinétique détaillée de l’oxydation du EDM. Le modèle de rupture de Kelvin-Helmholtz-Rayleigh- Taylor (KH-RT ainsi que le modèle de turbulence k-ε  RNG ont été appliqués pour analyser respectivement les caractéristiques du jet et l’écoulement turbulent. Pour prévoir la formation de NOx pendant la combustion

  6. PILOT DECONTAMINATION THROUGH PILOT SEQUENCE HOPPING IN MASSIVE MIMO SYSTEMS

    DEFF Research Database (Denmark)

    2015-01-01

    path between one of the users and one of the base stations define one of the channels. The system comprises a pilot generation unit configured to assign pilot sequences randomly among the users and a pilot processing unit configured to filter the pilot sequences received from a user of interest so...... that the channel coefficient of the channel of the user of interest is determined. The pilot sequences received from the user of interest are contaminated by other non-orthogonal or identical pilot sequences from other users of the cell of interest or other cells. The filter is configured so that the contamination...... caused by the other non-orthogonal or identical pilot sequences from the other users is reduced....

  7. Process of quantity determination of uranium by chromatography in liquid zone

    International Nuclear Information System (INIS)

    Muller, J.P.; Cojean, J.; Daubizit, M.

    1993-01-01

    The invention concerns a process of quantity determination of uranium by chromatography in liquid zone, usable to determine the quantity of uranium traces. Solutions to be treated can be aqueous or organic

  8. Order Quantity Distributions: Estimating an Adequate Aggregation Horizon

    Directory of Open Access Journals (Sweden)

    Eriksen Poul Svante

    2016-09-01

    Full Text Available In this paper an investigation into the demand, faced by a company in the form of customer orders, is performed both from an explorative numerical and analytical perspective. The aim of the research is to establish the behavior of customer orders in first-come-first-serve (FCFS systems and the impact of order quantity variation on the planning environment. A discussion of assumptions regarding demand from various planning and control perspectives underlines that most planning methods are based on the assumption that demand in the form of customer orders are independently identically distributed and stem from symmetrical distributions. To investigate and illustrate the need to aggregate demand to live up to these assumptions, a simple methodological framework to investigate the validity of the assumptions and for analyzing the behavior of orders is developed. The paper also presents an analytical approach to identify the aggregation horizon needed to achieve a stable demand. Furthermore, a case study application of the presented framework is presented and concluded on.

  9. Deep groundwater quantity and quality in the southwestern US

    Science.gov (United States)

    Kang, M.; Ayars, J. E.; Jackson, R. B.

    2017-12-01

    Groundwater demands are growing in many arid regions and adaptation through the use of non-traditional resources during extreme droughts is increasingly common. One such resource is deep groundwater, which we define as deeper than 300 m and up to several kilometer-depths. Although deep groundwater has been studied in the context of oil and gas, geothermal, waste disposal, and other uses, it remains poorly characterized, especially for the purposes of human consumption and irrigation uses. Therefore, we evaluate deep groundwater quantity and quality within these contexts. We compile and analyze data from water management agencies and oil and gas-based sources for the southwestern US, with a detailed look at California's Central Valley. We also use crop tolerance thresholds to evaluate deep groundwater quality for irrigation purposes. We find fresh and usable groundwater volume estimates in California's Central Valley to increase by three- and four-fold respectively when depths of up to 3 km are considered. Of the ten basins in the southwestern US with the most data, we find that the Great Basin has the greatest proportions of fresh and usable deep groundwater. Given the potentially large deep groundwater volumes, it is important to characterize the resource, guard against subsidence where extracted, and protect it for use in decades and centuries to come.

  10. Ship waste quantities prediction model for the port of Belgrade

    Directory of Open Access Journals (Sweden)

    VLADANKA PRESBURGER ULNIKOVIĆ

    2011-06-01

    Full Text Available This study focuses on the issues related to the waste management in river ports in general and especially in the port of Belgrade. Data on solid waste, waste oils, oily waters, gray water and black water have been collected for a period of five years. The methodology of data collection is presented. Trends of data were analyzed and the regression model was used to predict the waste quantities in the Belgrade port. This data could be utilized as a basis for the calculation of the equipment capacity for waste selective collection, treatment and storage. The results presented in this study establish the need for an orga¬nized management system for this type of waste which can be achieved either by constructing and providing new specialized terminal or by providing mobile floating facilities and other plants in the Port of Belgrade for these kinds of ser¬vices. In addition to the above, the legislative and organizational strategy of waste management has been explored to complete the study because the im¬pact of good waste management on environment and prevention of environ¬mental accidents would be highly beneficial. This study demonstrated that ad¬dressing these issues should be considered at international as well as national level.

  11. Quality and quantity of construction and demolition waste in Tehran.

    Science.gov (United States)

    Asgari, Alireza; Ghorbanian, Tahereh; Yousefi, Nader; Dadashzadeh, Dariush; Khalili, Fatemeh; Bagheri, Amin; Raei, Mehdi; Mahvi, Amir Hossein

    2017-01-01

    In recent years the generation rate of construction and demolition waste (C&D) has significantly augmented. The aim of this study was to assessed the quality and quantity of construction and demolition waste in Tehran (capital of Iran). Questionnaire methods were used for estimating the amount of generated C&D wastes national statistical data and typical waste generation data. In order to defining the composition of C&D waste, trucks were randomly selected and their wastes were separated and weighted. According to obtained results, about 82,646,051 m 3 of C&D waste (average 16,529,210 m 3 per year) were generated during 2011 to 2016 which only about 26% of them has been recycled. Mixing sand and cement, concrete, broken bricks and soil have the highest amount of the composition of C&D waste in Tehran that was 30, 19, 18 and 11%, respectively. Based on the results, about 2,784,158 t of the waste will generate in 2025 and this is approximately 122% higher than wastes generate in 2016. Based on MAPSA's data, 360 teams of personnel cruise and control the illegal disposals, but due to the expansion of Tehran this number of teams is inadequate and can't be effective in controlling the situation. In general, the overall condition of C&D waste management in Tehran seems undesirable and needs to be updated based on the experience of successful countries in this field.

  12. Quantity and Quality of Inhaled Dose Predicts Immunopathology in Tuberculosis

    Directory of Open Access Journals (Sweden)

    Kevin Patrick Fennelly

    2015-06-01

    Full Text Available Experimental animal models of tuberculosis (TB have convincingly demonstrated that inhaled dose predicts immunopathology and survival. In contrast, the importance of inhaled dose has generally not been appreciated in TB epidemiology, clinical science, or the practice of TB control. Infectiousness of TB patients has traditionally been assessed using microscopy for acid-fast bacilli in the sputum, which should be considered only a risk factor. We have recently demonstrated that cough aerosol cultures from index cases with pulmonary TB are the best predictors of new infection among household contacts. We suggest that cough aerosols of M. tuberculosis are the best surrogates of inhaled dose, and we hypothesize that the quantity of cough aerosols is associated with TB infection versus disease. Although several factors affect the quality of infectious aerosols, we propose that the particle size distribution of cough aerosols is an important predictor of primary upper airway disease and cervical lymphadenitis and of immune responses in exposed hosts. We hypothesize that large droplet aerosols (> 5 microns containing M. tuberculosis deposit in the upper airway and can induce immune responses without establishing infection. We suggest that this may partially explain the large proportion of humans who never develop TB disease in spite of having immunological evidence of M. tuberculosis infection (e.g. positive TST or IGRA. If these hypotheses are proven true, they would alter the current paradigm of latent TB infection and reactivation, further demonstrating the need for better biomarkers or methods of assessing TB infection and the risk of developing disease.

  13. BIM IMPLEMENTATION IN A NEW ZEALAND CONSULTING QUANTITY SURVEYING PRACTICE

    Directory of Open Access Journals (Sweden)

    Curtis Harrison

    2015-07-01

    Full Text Available 5D BIM – generating cost data via the building information modelling (BIM process- has the potential to be used by quantity surveyors (QSs to streamline their workflows and increase their provision of quality service. Consultant QSs experienced in the use 5D BIM, from the New Zealand office of one large global practice, were interviewed on their perceptions of the benefits of, and barriers to, 5D BIM implementation within their firm. Findings suggest that 5D BIM has numerous benefits over traditional methods, chiefly through the increased efficiency and visualization that BIM provides, along with the rapid identification of design changes. However, realization of these perceived benefits limited to date, due to several barriers hindering 5D BIM implementation: incomplete design and insufficient model object data in the BIM model; a lack of standards to facilitate electronic measurement; legal issues, and a lack of government support. However, participants perceived that 5D BIM implementation will achieve these benefits to a far greater extent in the future. Further research is recommended to identify the BIM skills which QSs will need in the future to reach the full potential of 5D BIM

  14. Quantities of actinides in nuclear reactor fuel cycles

    International Nuclear Information System (INIS)

    Ang, K.P.

    1975-01-01

    The quantities of plutonium and other fuel actinides have been calculated for equilibrium fuel cycles for 1000 MW reactors of the following types: water reactors fueled with slightly enriched uranium, water reactors fueled with plutonium and natural uranium, fast-breeder reactors, gas-cooled reactors fueled with thorium and highly enriched uranium, and gas-cooled reactors fueled with thorium, plutonium, and recycled uranium. The radioactivity levels of plutonium, americium, and curium processed yearly in these fuel cycles are greatest for the water reactors fueled with natural uranium and recycled plutonium. The total amount of actinides processed is calculated for the predicted future growth of the United States nuclear power industry. For the same total installed nuclear power capacity, the introduction of the plutonium breeder has little effect upon the total amount of plutonium processed in this century. The estimated amount of plutonium in the low-level process wastes in the plutonium fuel cycles is comparable to the amount of plutonium in the high-level fission product wastes. The amount of plutonium processed in the nuclear fuel cycles can be considerably reduced by using gas-cooled reactors to consume plutonium produced in uranium-fueled water reactors. These, and other reactors dedicated for plutonium utilization, could be co-located with facilities for fuel reprocessing and fuel fabrication to eliminate the off-site transport of separated plutonium. (U.S.)

  15. Dynamic Coding of Signed Quantities in Cortical Feedback Circuits

    Directory of Open Access Journals (Sweden)

    Dana eBallard

    2012-08-01

    Full Text Available In the early sensory and motor areas of the cortex, individual neurons transmit information about specific sensory features via a peaked response. This concept has been crystallized as `labeled lines,' to denote that axons communicate the specific properties of their sensory or motor parent cell. Such cells also can be characterized as being polarized, that is, as representing a signed quantity that is either positive or negative. We show in a model simulation that there are two important consequences when learning receptive fields using such signed codings in circuits that subtract different inputs. The first is that, in feedback circuits using labeled lines, such arithmetic operations need to be distributed across multiple distinct pathways. The second consequence is that such pathways must be necessarily dynamic, i.e. that synapses can grow and retract when forming receptive fields. The model monitors the breaking and growing of new circuit connections when their synapses need to change polarities and predicts that the rate of such changes should be inversely correlated with the progress of receptive field formation.

  16. Sound radiation quantities arising from a resilient circular radiator.

    Science.gov (United States)

    Aarts, Ronald M; Janssen, Augustus J E M

    2009-10-01

    Power series expansions in ka are derived for the pressure at the edge of a radiator, the reaction force on the radiator, and the total radiated power arising from a harmonically excited, resilient, flat, circular radiator of radius a in an infinite baffle. The velocity profiles on the radiator are either Stenzel functions (1-(sigma/a)2)n, with sigma the radial coordinate on the radiator, or linear combinations of Zernike functions Pn(2(sigma/a)2-1), with Pn the Legendre polynomial of degree n. Both sets of functions give rise, via King's integral for the pressure, to integrals for the quantities of interest involving the product of two Bessel functions. These integrals have a power series expansion and allow an expression in terms of Bessel functions of the first kind and Struve functions. Consequently, many of the results in [M. Greenspan, J. Acoust. Soc. Am. 65, 608-621 (1979)] are generalized and treated in a unified manner. A foreseen application is for loudspeakers. The relation between the radiated power in the near-field on one hand and in the far field on the other is highlighted.

  17. Energy taxes, resource taxes and quantity rationing for climate protection

    Energy Technology Data Exchange (ETDEWEB)

    Eisenack, Klaus [Oldenburg Univ. (Germany). Dept. of Economics; Edenhofer, Ottmar; Kalkuhl, Matthias [Potsdam-Institut fuer Klimafolgenforschung e.V., Potsdam (Germany)

    2010-11-15

    Economic sectors react strategically to climate policy, aiming at a re-distribution of rents. Established analysis suggests a Pigouvian emission tax as efficient instrument, but also recommends factor input or output taxes under specific conditions. However, existing studies leave it open whether output taxes, input taxes or input rationing perform better, and at best only touch their distributional consequences. When emissions correspond to extracted ressources, it is questionable whether taxes are effective at all. We determine the effectiveness, efficiency and functional income distribution for these instruments in the energy and resource sector, based on a game theoretic growth model with explicit factor markets and policy instruments. Market equilibrium depends on a government that acts as a Stackelberg leader with a climate protection goal. We find that resource taxes and cumulative resource quantity rationing achieve this objective efficiently. Energy taxation is only second best. Mitigation generates a substantial ''climate rent'' in the resource sector that can be converted to transfer incomes by taxes. (orig.)

  18. Evaluatie pilot Financieringslink

    NARCIS (Netherlands)

    Rosenboom, N.; Rougoor, W.; Fijnje, J.; Biesenbeek, C.

    Veel mkb-ondernemers hebben moeite om financiering te krijgen. Daarom heeft het ministerie van Economische Zaken in 2015 de pilot Financieringslink (Fink) opgezet– een online portal waar het mkb een financieringsverkenning kan indienen. Het hoofddoel van Fink is het verbeteren, standaardiseren en

  19. The Epoch Pilot Program.

    Science.gov (United States)

    Uhlenberg, Donald M.; Molenaar, Richard A.

    1982-01-01

    Describes a program for high school students who are between their junior and senior years which provides an opportunity to take part in aviation courses at the University of North Dakota. Students take courses leading to a private pilot license, and earn college credit for their efforts. (JN)

  20. Evaluatie pilot Endogene Factoren

    NARCIS (Netherlands)

    Viet AL; Fiolet D; Voortman JK; Rover C de; Hanning C; Uitenbroek D; Loon AJM van; PZO; GGD Achterhoek; GGD Midden Holland; GG&GD Amsterdam

    2004-01-01

    As a part of the project on the Local and National Monitor for Public Health several pilot studies were carried out in three Municipal Health Centres (GGDs). The first aim was to investigate the feasibility of a physical examination at the health centre in combination with a health interview (or

  1. Symbolic Estrangement: Evidence against a Strong Association between Numerical Symbols and the Quantities They Represent

    Science.gov (United States)

    Lyons, Ian M.; Ansari, Daniel; Beilock, Sian L.

    2012-01-01

    Are numerals estranged from a sense of the actual quantities they represent? We demonstrate that, irrespective of numerical size or distance, direct comparison of the relative quantities represented by symbolic and nonsymbolic formats leads to performance markedly worse than when comparing 2 nonsymbolic quantities (Experiment 1). Experiment 2…

  2. 48 CFR 245.7309-8 - Variations in quantity or weight.

    Science.gov (United States)

    2010-10-01

    ... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

  3. 40 CFR 273.8 - Applicability-household and conditionally exempt small quantity generator waste.

    Science.gov (United States)

    2010-07-01

    ... conditionally exempt small quantity generator waste. 273.8 Section 273.8 Protection of Environment ENVIRONMENTAL....8 Applicability—household and conditionally exempt small quantity generator waste. (a) Persons... universal wastes defined at § 273.9; and/or (2) Conditionally exempt small quantity generator wastes that...

  4. Forest Biomass Energy Resources in China: Quantity and Distribution

    Directory of Open Access Journals (Sweden)

    Caixia Zhang

    2015-11-01

    Full Text Available As one of the most important renewable and sustainable energy sources, the forest biomass energy resource has always been the focus of attention of scholars and policy makers. However, its potential is still uncertain in China, especially with respect to its spatial distribution. In this paper, the quantity and distribution of Chinese forest biomass energy resources are explored based mainly on forestry statistics data rather than forest resource inventory data used by most previous studies. The results show that the forest biomass energy resource in China was 169 million tons in 2010, of which wood felling and bucking residue (WFBR,wood processing residue (WPR, bamboo processing residue, fuel wood and firewood used by farmers accounted for 38%, 37%, 6%, 4% and 15%, respectively. The highest resource was located in East China, accounting for nearly 39.0% of the national amount, followed by the Southwest and South China regions, which accounted for 17.4% and 16.3%, respectively. At the provincial scale, Shandong has the highest distribution, accounting for 11.9% of total resources, followed by Guangxi and Fujian accounting for 10.3% and 10.2%, respectively. The actual wood-processing residue (AWPR estimated from the actual production of different wood products (considering the wood transferred between regions showed apparent differences from the local wood processing residue (LWPR, which assumes that no wood has been transferredbetween regions. Due to the large contribution of WPR to total forestry bioenergy resources, the estimation of AWPR will provide a more accurate evaluation of the total amount and the spatial distribution of forest biomass energy resources in China.

  5. On Complex Networks Representation and Computation of Hydrologycal Quantities

    Science.gov (United States)

    Serafin, F.; Bancheri, M.; David, O.; Rigon, R.

    2017-12-01

    Water is our blue gold. Despite results of discovery-based science keep warning public opinion about the looming worldwide water crisis, water is still treated as a not worth taking resource. Could a different multi-scale perspective affect environmental decision-making more deeply? Can also a further pairing to a new graphical representation of processes interaction sway decision-making more effectively and public opinion consequently?This abstract introduces a complex networks driven way to represent catchments eco-hydrology and related flexible informatics to manage it. The representation is built upon mathematical category. A category is an algebraic structure that comprises "objects" linked by "arrows". It is an evolution of Petri Nets said Time Continuous Petri Nets (TCPN). It aims to display (water) budgets processes and catchment interactions using explicative and self-contained symbolism. The result improves readability of physical processes compared to current descriptions. The IT perspective hinges on the Object Modeling System (OMS) v3. The latter is a non-invasive flexible environmental modeling framework designed to support component-based model development. The implementation of a Directed Acyclic Graph (DAG) data structure, named Net3, has recently enhanced its flexibility. Net3 represents interacting systems as complex networks: vertices match up with any sort of time evolving quantity; edges correspond to their data (fluxes) interchange. It currently hosts JGrass-NewAge components, and those implementing travel time analysis of fluxes. Further bio-physical or management oriented components can be easily added.This talk introduces both graphical representation and related informatics exercising actual applications and examples.

  6. Technology development for evaluation of operational quantities in radiation protection

    International Nuclear Information System (INIS)

    Jang, Si Young; Lee, T. Y.; Kim, B. H.

    2003-03-01

    Korean government recently published a national regulation on the internal exposure monitoring and dose evaluation (internal dosimetry) based on the most recent ICRP recommendation 60 and subsequent publications, which supercede the former ICRP recommendation 26 and publication 30, on which the internal dosimetry practice in Korea had been based so far. Consequently, this project, according to the demand from both government and nuclear industry, had been launched to develop a user-friendly computer code on internal dosimetry adopting the most up to date ICRP biokinetic and dosimetric model to resolve the difficulties and problems faced to nuclear industry and to develop related technology. The reliability of this code, named as BiDAS, as a result of several benchmark calculations for self assurance appeared to be excellent comparing with the foreign computer code. This computer code is expected to be successfully utilized in nuclear industry and related fields in complying with the national regulation on internal dosimetry program started from late 2003. Reference low level gamma(γ) radiation field for calibration of environmental radiation(γ) monitor and reference neutron field for calibration of n monitoring equipment have been established and characterized. International cross comparison of these reference radiation fields have been performed and radiation response of various radiation monitoring instrument has been tested by using these reference radiation fields. A technology which can directly measure the radiation quality factor and tissue absorbed dose has been established to evaluate the neutron dose in terms of operational quantity in the unknown mixed n-γ radiation field. Spherical and cylindrical TEPC systems have been designed and manufactured and a portable TEPC system to measure the neutron quality and dose in the real work field has been developed and tested in accelerator laboratory

  7. WEB TECHNOLOGIES USED TO FORECAST FUTURE WASTE QUANTITIES

    Directory of Open Access Journals (Sweden)

    Valeriu LUPU

    2014-06-01

    Full Text Available In this article the authors propose a modality of prognosis of the quantities of waste generated in a certain period. The proposition was finalized by achieving a model of prognosis present on a site hosted by a Web server. The software solve the problem for the general case, depending on the input data after analysis. After analyzing input data sets are used with one, two or three components (trend, seasonality and residual variable. According to the input data the adjustment model regarding the description of the analyzed phenomenon (additive and multiplying is chosen. If the chronogram of the analyzed phenomenon indicates an oscillating evolution, of sinusoidal nature, the additive model (+ is chosen, otherwise the multiplying model (  is chosen. The seasonal component is estimated and the deseasonalized chronological series is determined. The seasonality is determined by: the procedure of arithmetical means, the procedure of moving averages and the procedure of analytical tendency. The adjustment function is specified regarding the tendency of the phenomenon and its parameters are estimated. The significance of the adjustment function is verified specifying the significance threshold with which it may be accepted as significant. The estimation of the parameters of the adjustment function is made on the basis of the application of the method of least squares. The values of the phenomenon on two or three trimesters/ months are estimated for the processed data (by using time series with two or three steps ahead. Several types of waste specified by the value of the meter for waste from the database may be accepted. The model proposed makes decisions and justifies if the data prognosticated is accepted or not. All information from the input data to the final data is stored in a MySQL database.

  8. Influence of adhesive bonding on quantity of emissions VOCs

    Directory of Open Access Journals (Sweden)

    Petr Čech

    2008-01-01

    Full Text Available The study deals with the influence of urea-formaldehyde glue and veneered bolstering on technological operation veneering on quantity of emission VOCs (volatile organic compounds.The so-called Volatile Organic Compounds (VOC are among the largest pollution sources of both the internal and external environments.VOC is defined as emission of any organic compound or a mixture thereof, with the exception of methane, whereby the compound exerts the pressure of 0.01 kPa or more at the temperature of 20 °C (293.15 K and reaches the corresponding volatility under the specific conditions of its use and can undergo photochemical reactions with nitrogen oxides when exposed to solar radiation.The effects of VOC upon environment can be described by equation:VOC + NOx + UV radiation + heat = tropospheric ozone (O3.In this work there were tested background working environment in various parts of multi-storeyed press, next was judged emissive charge of veneered device and used glue. We used surface material such as chipboard. We used urea-formaldehyde glue KRONOCOL U300 on technological operation veneering.The VOC emissions from the wooden surfaces with or without finishing were tested in the Equipment for VOC Measuring with a small-space chamber. This equipment was installed in and made available by the Institute of Furniture, Design and Habitation. The small-space chamber is suitable for testing small parts of wood products. The device equipped with small-chamber satisfies all conditions mandated in the standard ENV 13 419 DIN -V-ENV 13 419 ”Determination of the emissions of Volatile organic compounds”.The VOC emissions were collected in columns with sorbent Tenax TA. We analyzed the columns with the VOC emissions by: the gas chromatography in conjunction with mass spectrometer and Direct Thermal Desorption.

  9. Calculation of uncertainties in influence quantities in biological essays

    Directory of Open Access Journals (Sweden)

    Pierre Morel

    2006-01-01

    Full Text Available Due to the need of showing the reliability of results from biological essays, such as in health and environmental areas, laboratories have been implementing quality systems, particularly ABNT NBR ISO/IEC 17025 (ABNT, 2001, which include as one of the requirements, the calculation of uncertainty in essays results. It is of common knowledge that estimating uncertainty in essays using organisms, such as animal and vegetal species, is difficult, preventing from meeting that requirement in the standard. The paper shows the calculation of uncertainties in influences quantities in these essays as a tool to allow validating the measuring process, by using the essays performed by Rhodia Environmental Impact Analysis Laboratory and IPEN Ecotoxicology Laboratory as examples.Devido à necessidade de demonstrar a confiabilidade dos resultados de ensaios biológicos como, por exemplo, nas áreas de saúde e ambiental, laboratórios vêm implementando sistemas da qualidade, em especial a ABNT NBR ISO/IEC 17025 (ABNT, 2001 que inclui como um dos requisitos o cálculo da incerteza dos resultados dos ensaios. É reconhecidamente difícil de estimar a incerteza de ensaios que utilizam organismos, como com espécies animais e vegetais o que impede, consequentemente, o atendimento deste requisito da norma. O trabalho apresenta o cálculo de incerteza das grandezas de influências nestes ensaios como uma ferramenta que permite validar o processo de medição, utilizando como exemplos aqueles realizados pelos Laboratórios de Análise de Impacto Ambiental da Rhodia e de Ecologia e Ecotoxicologia do IPEN.

  10. Influence of Cattle Trails on Runoff Quantity and Quality.

    Science.gov (United States)

    Miller, Jim J; Curtis, Tony; Chanasyk, David S; Willms, Walter D

    2017-03-01

    Cattle trails in grazed pastures close to rivers may adversely affect surface water quality of the adjacent river by directing runoff to it. The objective of this 3-yr study (2013-2015) in southern Alberta, Canada, was to determine if cattle trails significantly increased the risk of runoff and contaminants (sediment, nutrients) compared with the adjacent grazed pasture (control). A portable rainfall simulator was used to generate artificial rainfall (140 mm h) and runoff. The runoff properties measured were time to runoff and initial abstraction (infiltration), total runoff depth and average runoff rates, as well as concentrations and mass loads of sediment, N, and P fractions. Cattle trails significantly ( ≤ 0.10) decreased time to runoff and initial abstraction (26-32%) in the 2 yr measured and increased total runoff depth, runoff coefficients, and average runoff rates (21-51%) in 2 of 3 yr. Concentrations of sediment, N, and P fractions in runoff were not significantly greater for cattle trails than for control areas. However, mass loads of total suspended solids (57-85% increase), NH-N (31-90%), and dissolved reactive P (DRP) (30-92%) were significantly greater because of increased runoff volumes. Overall, runoff quantity and loads of sediment, NH-N, and DRP were greater for cattle trails compared with the adjacent grazed pasture, and hydrologic connection with cattle-access sites on the riverbank suggests that this could adversely affect water quality in the adjacent river. Extrapolation of the study results should be tempered by the specific conditions represented by this rainfall simulation study. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  11. 76 FR 63183 - Pilot in Command Proficiency Check and Other Changes to the Pilot and Pilot School Certification...

    Science.gov (United States)

    2011-10-12

    ...-0938; Amendment Nos. 61-128, 91-324, 141-15, and 142-7] RIN 2120-AJ18 Pilot in Command Proficiency Check and Other Changes to the Pilot and Pilot School Certification Rules; Correction AGENCY: Federal... regulations to revise the pilot, flight instructor, and pilot school certification requirements. In particular...

  12. 77 FR 71089 - Pilot Loading of Aeronautical Database Updates

    Science.gov (United States)

    2012-11-29

    ...) card, rather than in resident memory. The database update was accomplished by removing the SD card with... frequency distance measuring equipment (DME), and any updates that affect system operating software--that... developed with attention to data integrity. Current technology uses databases which are developed in...

  13. Revised concept for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    Dennis, A.W.; Milloy, J.A.; Scully, L.W.; Shefelbine, H.C.; Stinebaugh, R.E.; Wowak, W.E.

    1978-07-01

    The quantities of remotely handled wastes that must be handled at the Waste Isolation Pilot Plant have been reduced from 250 x 10 3 ft 3 /y to 10 x 10 3 ft 3 /y; the capital cost of the facility will be reduced from 534 to 428 million dollars. Changes in the facility design due to the reduction in the amount of remote-handled waste are discussed. If DOE should exercise its option to construct a high-level waste repository concurrently with the construction of the revised design, with both facilities receiving waste in 1985, the combined cost would be about 580 million dollars. However, it is unlikely that significant quantities of high-level waste in a form suitable for geologic disposal would be available until after 1990. (13 figures, 5 tables)

  14. Agricultural Pilot's Audiological Profile

    Directory of Open Access Journals (Sweden)

    Foltz, Lucas

    2010-09-01

    Full Text Available Introduction: The agricultural airplane pilot are daily exposed to intense noises, being susceptible to the noise-induced hearing loss (NIHL and its auditory and extra auditory effects. Objective: To analyze the audiological profile of this population, verifying the work's influence on its hearing. Method: It was realized a retrospective, individual, observational, and cross-sectional study through the data obtained by means of a questionnaire and audiometric thresholds of 41 agricultural pilots. To the statistical analysis were utilized the chi-square, Spearman, and Wilcoxon tests with significance level of 5%. Results: It was verified that 95,1% of the pilots use PPE ( personal protective equipment during flight and 58,5% have contact with pesticides. More than half of individuals referred to feel auditory and extra auditory symptoms, being the buzz the more frequent (29,1%. It has the occurrence of 29,3% of NIHL suggestive hearing loss and 68,3% of normality, taking this presence of unilateral notch in 24,4% and bilateral notch in 31,7%. It was found correlation statistically significant in the associations between time of service and the average of the acute frequencies in the right ear (p=0038, and in the left ear (p=0,010. It has a statistical tendency in the association between audiometric configuration and contact with pesticides (p=0,088. Conclusion: The hearing loss prevalence in this study was showed high. More than half of the sample has normal audiometric thresholds with notch configuration. Such data lead to the conclusion that the agricultural pilots, even with PPE use, they still suffer with the damages caused by noise, needing best proposals of hearing loss prevention.

  15. Process Experimental Pilot Plant

    International Nuclear Information System (INIS)

    Henze, H.

    1986-01-01

    The Process Experimental Pilot Plant (PREPP) at the Idaho National Engineering Laboratory (INEL) was built to convert transuranic contaminated solid waste into a form acceptable for disposal at the Waste Isolation Pilot Plant (WIPP), located near Carlsbad, New Mexico. There are about 2.0 million cubic ft of transuranic waste stored at the Transuranic Storage Area of the INEL's Radioactive Waste Management Complex (RWMC). The Stored Waste Examination Pilot Plant (SWEPP) located at the RWMC will examine this stored transuranic waste to determine if the waste is acceptable for direct shipment to and storage at WIPP, or if it requires shipment to PREPP for processing before shipment to WIPP. The PREPP process shreds the waste, incinerates the shredded waste, and cements (grouts) the shredded incinerated waste in new 55-gal drums. Unshreddable items are repackaged and returned to SWEPP. The process off-gas is cleaned prior to its discharge to the atmosphere, and complies with the effluent standards of the State of Idaho, EPA, and DOE. Waste liquid generated is used in the grouting operation

  16. 76 FR 19267 - Pilot, Flight Instructor, and Pilot School Certification; Technical Amendment

    Science.gov (United States)

    2011-04-07

    .... No. 61-127] RIN 2120-AI86 Pilot, Flight Instructor, and Pilot School Certification; Technical... for pilots, flight instructors, ground instructors, and pilot schools. This document reinstates two... entitled, ``Pilot, Flight Instructor, and Pilot School Certification; Final Rule'' (74 FR 42500). That...

  17. LANCELOT pilot report, June 2007

    DEFF Research Database (Denmark)

    Levinsen, Karin; Meyer, Bente

    The aim of the Lancelot pilot evaluation process was to understand how teachers learn to teach and to relate to the online environment through the specific context of the Lancelot live online course. Following the Action Research in the autumn of 2006 the LANCELOT live online language course...... was revised for the piloting in the spring of 2007. A second aim of the pilot evaluation has therefore been to assess the revision of the course following the Action Research....

  18. The Importance of Pilot Studies

    OpenAIRE

    Van Teijlingen, Edwin; Hundley, Vanora

    2001-01-01

    The term 'pilot studies' refers to mini versions of a full-scale study (also called 'feasibility' studies), as well as the specific pre-testing of a particular research instrument such as a questionnaire or interview schedule. \\ud Pilot studies are a crucial element of a good study design. Conducting a pilot study does not guarantee success in the main study, but it does increase the likelihood. \\ud Pilot studies fulfil a range of important functions and can provide valuable insights for othe...

  19. Memory for multiple cache locations and prey quantities in a food-hoarding songbird

    Directory of Open Access Journals (Sweden)

    Nicola eArmstrong

    2012-12-01

    Full Text Available Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes, a food hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with 1. the number of cache sites containing prey rewards and 2. the length of time separating cache creation and retrieval (retention interval. Results showed that subjects generally performed above chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3 and 4 cache sites from between 1, 10 and 60 seconds. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to one minute long retention intervals without training.

  20. Principles and foundation: national standards on quantities and units in nuclear science field

    International Nuclear Information System (INIS)

    Chen Lishu

    1993-11-01

    The main contents of National Standards on Quantities and units of atomic and nuclear physics (GB 3102.9) and Quantities and Units of nuclear reactions and ionizing radiations (GB 310.10) are presented in which most important quantities with their symbols and definitions in the nuclear scientific field are given. The principles and foundation, including the International System of Units (SI) and its application to the nuclear scientific field, in the setting of the National Standards are explained

  1. Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

    International Nuclear Information System (INIS)

    Bertone, P.C.

    1985-01-01

    The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

  2. Quantity-split strategy under two-contractor competitive procurement environment

    OpenAIRE

    Boger, Dan C.; Liao, Shu S.

    1988-01-01

    This report discusses the various market scenarios that provide bid price manipulation opportunities under the dual source competition environment. Two different quantity-split strategies were developed one for the case when one of the suppliers does not have the capacity to produce the majority of the annual quantity requirement and the other for the case when neither contractor is interested in using low prices to capture the larger share of annual quantity. Keywords: Dual sourcing, Quantit...

  3. Pilot unit for cesium-137 separation; Unite pilote de separation du cesium-137

    Energy Technology Data Exchange (ETDEWEB)

    Raggenbass, A; Quesney, M; Fradin, J; Dufrene, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Users of radiation are becoming increasingly interested in cesium-137. At the same time the starting up of the industrial plant at Marcoule will make available in the near future large stocks of fission products which should be made use of as quickly as possible. The installation described is a pilot plant for cesium-137 production which should make it possible: - to verify the chemical method on actual solutions of fission products, by treating about 100 curies of {sup 137}Cs by operation, - to obtain technical information on the chemical equipment (tele-commands, corrosion, maintenance, etc...), - to obtain {sup 137}Cs in sufficient quantity to perfect the technique of the manufacture of sealed sources. (author)Fren. [French] L'interet des utilisateurs de rayonnement se porte de plus en plus vers le caesium-137. Parallelement, la mise en oeuvre de l'ensemble industriel de Marcoule nous permettra de disposer dans un avenir proche de stocks importants de produits de fission qu'il sera interessant de valoriser au plus vite. L'installation que nous decrivons est un pilote de production de caesium-137 qui doit nous permettre: - de verifier la methode chimique sur des solutions de produits de fission reelles en traitant environ 100 curies de {sup 137}Cs par operation; - d'obtenir des renseignements techniques sur l'appareillage chimique (telecommandes, corrosion, entretien, etc...); - d'obtenir du {sup 137}Cs en quantite suffisante pour mettre au point la technique de fabrication des sources scellees. (auteur)

  4. Lie-Mei symmetry and conserved quantities of the Rosenberg problem

    International Nuclear Information System (INIS)

    Liu Xiao-Wei; Li Yuan-Cheng

    2011-01-01

    The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry. (general)

  5. Lie-Mei symmetry and conserved quantities of the Rosenberg problem

    Science.gov (United States)

    Liu, Xiao-Wei; Li, Yuan-Cheng

    2011-07-01

    The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

  6. 76 FR 82320 - Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports

    Science.gov (United States)

    2011-12-30

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 332-288] Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports AGENCY: United States International Trade Commission. [[Page 82321

  7. [Pärtel Lippus. The acoustic features and perception of the Estonian quantity system] / Stefan Werner

    Index Scriptorium Estoniae

    Werner, Stefan

    2012-01-01

    Arvustus: Pärtel Lippus. The acoustic features and perception of the Estonian quantity system. Tartu : Tartu University Press, 2011. (Dissertationes philologiae estonicae Universitatis Tartuensis ; 29)

  8. On the Output-Inflation Relationship When Price and Quantity Adjustments are Costly

    DEFF Research Database (Denmark)

    Danziger, Leif; Kreiner, Claus Thustrup

    A vast literature analyzes the real effects of price-adjustment costs assuming that quantity adjustments are costless. In this paper, we analyze whether the presence of quantity-adjustments costs, which presumably are significant, change the traditional results on the impact of inflation....... In particular, recent findings suggest that quantity-adjustment costs may remove the linkage between output and inflation. We show that this is not the case when inflation is anticipated. On the contrary, quantity-adjustment costs may significantly amplify the consequences of price-adjustment costs...

  9. Patterns in new dimensionless quantities containing melting temperature, and their dependence on pressure

    Directory of Open Access Journals (Sweden)

    U. WALZER

    1980-06-01

    Full Text Available The relationships existing between melting temperature and other
    macroscopic physical quantities are investigated. A new dimensionless
    quantity Q(1 not containing the Grtineisen parameter proves to be suited for serving in future studies as a tool for the determination of the melting temperature in the outer core of the Earth. The pressure dependence of more general dimensionless quantities Q„ is determined analytically and, for the chemical elements, numerically, too. The patterns of various interesting dimensionless quantities are shown in the Periodic Table and compared.

  10. Quantity assessment of waste in the dismantlement of liquid waste treatment plant and its actual state

    International Nuclear Information System (INIS)

    Uchiyama, Takafumi; Mitsuhashi, Ishi; Matsumoto, Tetsuo; Morishima, Kayoko; Tanzawa, Tomio

    2016-01-01

    From the progress of decommissioning project work of Tokyo City University Atomic Energy Research Institute, this paper reports the comparison between the actual amount of the waste generated during dismantlement work at liquid waste treatment facilities and the assessment quantity before starting the dismantlement. The quantity assessment was made on the basis of the installation license application, design specifications, drawings, records, history of use, site investigation results, etc. Since this quantity assessment did not take into account the dismantling contents of reservoir concrete, the assessed quantity of non-radioactive waste (NR waste) did not match the sum of actual NR waste. However, if an actually generated quantity of concrete of radioactive waste was added to the quantity assessment as NR waste, the quantity of actually generated NR waste and that of assessed NR waste were nearly consistent, which verified the validity of this assessment. This method is considered to be able to be utilized in the future quantity assessment of decommissioning work and the like. On the other hand, it was found that the number of drums that were actually stored tended to increase more than the estimated number of drum conversion. In old buildings, it is necessary to take into account the generation of waste other than radioactive materials in the quantity assessment stage and dismantlement stage. (A.O.)

  11. [Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

    Science.gov (United States)

    Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

    2011-12-01

    To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

  12. Pilot plant study

    International Nuclear Information System (INIS)

    Morris, M.E.

    1978-01-01

    Sandia Laboratories undertook the design and fabrication of an 8 ton/day dry sewage sludge irradiatior. The facility is intended (1) to function as a high-gamma-dose rate research facility; (2) to be a testbed for the unique electrical and mechanical components to be used in larger facilities; (3) to fulfill the formal requirements of a pilot plant so that design and construction of a demonstration facility could proceed; and (4) to provide accurate data base on construction and operating experience for the Environmental Impact Assessment (EIA), the Safety Analysis Report (SAR), and the cost analyses for a larger facility. The facility and its component systems are described in detail

  13. Priming a Pilot Implementation

    DEFF Research Database (Denmark)

    Hansen, Magnus; Ie Pedersen, Maria

    Abstract. We report on the initial findings of an action research study about effects specifications. It is a part of larger IS pilot implementation project conducted in the Danish healthcare sector. Through interviews and a workshop we have identified and specified the main effects that comprise...... the basis for the evaluation of the project. The study indicates that cross-organisational effects specifications cause a significant number of effects. To further prioritize these we argue that both interview and workshop must be facilitated as mutual learning processes between interviewer and interviewee....

  14. Effects of pilot holes on longitudinal miniscrew stability and bony adaptation.

    Science.gov (United States)

    Carney, Lauren Ohlenforst; Campbell, Phillip M; Spears, Robert; Ceen, Richard F; Melo, Ana Cláudia; Buschang, Peter H

    2014-11-01

    The purposes of this study were to longitudinally evaluate the effects of pilot holes on miniscrew implant (MSI) stability and to determine whether the effects can be attributed to the quality or the quantity of bone surrounding the MSI. Using a randomized split-mouth design in 6 skeletally mature female foxhound-mix dogs, 17 MSIs (1.6 mm outer diameter) placed with pilot holes (1.1 mm) were compared with 17 identical MSIs placed without pilot holes. Implant stability quotient measurements of MSI stability were taken weekly for 7 weeks. Using microcomputed tomography with an isotropic resolution of 6 μm, bone volume fractions were measured for 3 layers of bone (6-24, 24-42, and 42-60 μm) surrounding the MSIs. At placement, the MSIs with pilot holes showed significantly (P holes (48.3 vs 47.5). Over time, the implant stability quotient values decreased significantly more for the MSIs placed with pilot holes than for those placed without pilot holes. After 7 weeks, the most coronal aspect of the 6- to 24-μm layer of cortical bone and the most coronal aspects of all 3 layers of trabecular bone showed significantly larger bone volume fractions for the MSIs placed without pilot holes than for those placed with pilot holes. MSIs placed with pilot holes show greater primary stability, but greater decreases in stability over time, due primarily to having less trabecular bone surrounding them. Copyright © 2014 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  15. Enlisted or Officer Drone Pilots

    Science.gov (United States)

    2010-04-01

    the property of the United States government. AU/ACSC/Rafnson, Gary B/AY10 3 Abstract This paper compares remotely piloted aircraft— drones ...operations in both the US Army and US Air Force. It argues that officers should continue to pilot Air Force drones because of the increased risks and

  16. Prediction of pilot induced oscillations

    Directory of Open Access Journals (Sweden)

    Valentin PANĂ

    2011-03-01

    Full Text Available An important problem in the design of flight-control systems for aircraft under pilotedcontrol is the determination of handling qualities and pilot-induced oscillations (PIO tendencieswhen significant nonlinearities exist in the vehicle description. The paper presents a method to detectpossible pilot-induced oscillations of Category II (with rate and position limiting, a phenomenonusually due to a misadaptation between the pilot and the aircraft response during some tasks in whichtight closed loop control of the aircraft is required from the pilot. For the analysis of Pilot in the LoopOscillations an approach, based on robust stability analysis of a system subject to uncertainparameters, is proposed. In this analysis the nonlinear elements are substituted by linear uncertainparameters. This approach assumes that PIO are characterized by a limit cycle behavior.

  17. Live Piloting and Prototyping

    Directory of Open Access Journals (Sweden)

    Francesca Rizzo

    2013-07-01

    Full Text Available This paper presents current trends in service design research concerning large scale projects aimed at generating changes at a local scale. The strategy adopted to achieve this, is to co-design solutions including future users in the development process, prototyping and testing system of products and services before their actual implementation. On the basis of experience achieved in the European Project Life 2.0, this paper discusses which methods and competencies are applied in the development of these projects, eliciting the lessons learnt especially from the piloting phase in which the participatory design (PD approach plays a major role. In the first part, the topic is introduced jointly with the theoretical background where the user center design and participatory design methods are presented; then the Life 2.0 project development is described; finally the experience is discussed from a service design perspective, eliciting guidelines for piloting and prototyping services in a real context of use. The paper concludes reflecting on the designers’ role and competencies needed in this process.

  18. The CVSA pilot study of highway vehicle inspection procedures for the transportation of radioactive materials

    International Nuclear Information System (INIS)

    Holm, J.; Curtis, G.E.; Branch, K.M.; Coburn, N.L.; Hauth, J.T.

    1991-01-01

    To further the goal of enhancing the safe and efficient transportation of radioactive materials, the US DOE and the Commercial Vehicle Safety Alliance have entered into a cooperative agreement to conduct a pilot study to test draft procedures for state inspections of highway route controlled quantity radioactive shipments. To succeed, this five-year study requires close collaboration between federal and state agencies and non-government organizations. Significant institutional relationships have been established for this study

  19. Pilots 2.0: DIRAC pilots for all the skies

    CERN Document Server

    Stagni, F; McNab, A; Luzzi, C

    2015-01-01

    In the last few years, new types of computing infrastructures, such as IAAS (Infrastructure as a Service) and IAAC (Infrastructure as a Client), gained popularity. New resources may come as part of pledged resources, while others are opportunistic. Most of these new infrastructures are based on virtualization techniques. Meanwhile, some concepts, such as distributed queues, lost appeal, while still supporting a vast amount of resources. Virtual Organizations are therefore facing heterogeneity of the available resources and the use of an Interware software like DIRAC to hide the diversity of underlying resources has become essential. The DIRAC WMS is based on the concept of pilot jobs that was introduced back in 2004. A pilot is what creates the possibility to run jobs on a worker node. Within DIRAC, we developed a new generation of pilot jobs, that we dubbed Pilots 2.0. Pilots 2.0 are not tied to a specific infrastructure; rather they are generic, fully configurable and extendible pilots. A Pilot 2.0 can be s...

  20. Price effects of changing quantities supplied at the integrated european fish market

    DEFF Research Database (Denmark)

    Nielsen, Max; Smit, Jos; Guillen, Jordi

    2012-01-01

    to be −1.1. This implies that price flexibilities previously estimated for single European countries underestimate price changes at the European level caused by quantity changes. Results indicate that changing quantities can increase revenues from individual species with large own-price flexibilities...

  1. 41 CFR 101-26.507-4 - Quantities in excess of the maximum order limitation.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Quantities in excess of... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND PROGRAM 26.5-GSA Procurement Programs § 101-26.507-4 Quantities in...

  2. On pure-strategy Nash equilibria in price-quantity games

    NARCIS (Netherlands)

    Bos, I.; Vermeulen, A.J.

    2015-01-01

    This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

  3. 48 CFR 852.270-2 - Bread and bakery products-quantities.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products... Bread and bakery products—quantities. As prescribed in 870.111-3, insert the following clause: Bread and Bakery Products—Quantities (JAN 2008) The bidder agrees to furnish up to 25 percent more or 25 percent...

  4. 29 CFR 780.814 - “Grown in commercial quantities.”

    Science.gov (United States)

    2010-07-01

    ... OF GENERAL POLICY OR INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT... “commercial” quantities, the trade understanding of what are “commercial” quantities of cotton would be...

  5. Non-Noether conserved quantity for differential equations of motion in the phase space

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A non-Noether conserved quantity for the differential equations of motion of mechanical systems in the phase space is studied. The differential equations of motion of the systems are established and the determining equations of Lie symmetry are given. An existence theorem of non-Noether conserved quantity is obtained. An example is given to illustrate the application of the result.

  6. Are Quantity Surveyors Competent to Value for Civil Engineering Works? Evaluating QSs' Competencies and Militating Factors

    Science.gov (United States)

    Olawumi, Timothy Oluwatosin; Ayegun, Olaleke Amos

    2016-01-01

    The role of the quantity surveyor is one that is often unclear amongst the general public. This study discussed the competencies of the quantity surveyor in measuring and managing civil engineering works and also carrying out the financial management for civil engineering construction projects; also outlined the various competencies and skills…

  7. Optimal trading quantity integration as a basis for optimal portfolio management

    Directory of Open Access Journals (Sweden)

    Saša Žiković

    2005-06-01

    Full Text Available The author in this paper points out the reason behind calculating and using optimal trading quantity in conjunction with Markowitz’s Modern portfolio theory. In the opening part the author presents an example of calculating optimal weights using Markowitz’s Mean-Variance approach, followed by an explanation of basic logic behind optimal trading quantity. The use of optimal trading quantity is not limited to systems with Bernoulli outcome, but can also be used when trading shares, futures, options etc. Optimal trading quantity points out two often-overlooked axioms: (1 a system with negative mathematical expectancy can never be transformed in a system with positive mathematical expectancy, (2 by missing the optimal trading quantity an investor can turn a system with positive expectancy into a negative one. Optimal trading quantity is that quantity which maximizes geometric mean (growth function of a particular system. To determine the optimal trading quantity for simpler systems, with a very limited number of outcomes, a set of Kelly’s formulas is appropriate. In the conclusion the summary of the paper is presented.

  8. 40 CFR 355.12 - What quantities of extremely hazardous substances trigger emergency planning requirements?

    Science.gov (United States)

    2010-07-01

    ... EMERGENCY PLANNING AND NOTIFICATION Emergency Planning Who Must Comply § 355.12 What quantities of extremely... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What quantities of extremely hazardous substances trigger emergency planning requirements? 355.12 Section 355.12 Protection of Environment...

  9. Variations of influence quantities in industrial irradiators and their effect on dosimetry performance

    International Nuclear Information System (INIS)

    Chu, R.D.H.

    1999-01-01

    Many environmental factors, including irradiation temperature, post-irradiation storage temperature, dose rate, relative humidity, oxygen content and the energy spectrum may affect the response of dosimetry systems used in industrial radiation processing. Although the effects of individual influence quantities have been extensively studied, the variations of these influence quantities in production irradiators and the complex relationships between the effects of different influence quantities make it difficult to assess the overall effect on the measurement uncertainty. In the development of new dosimetry systems it is important to know the effect of each influence quantity and developers of new dosimetry systems should perform studies over a wide range of irradiation conditions. Analysis parameters and manufacturing specifications should be chosen to minimize the effect of influence quantities in the environments where the dosimeters will be used. Because of possible relationships between different influence quantities, care must be taken to ensure that the response function determined in the calibration of the dosimetry system is applicable for the conditions in which the dosimeters will be used. Reference standard dosimetry systems which have been thoroughly studied and have known relationships between dose response and influence quantities should be used to verify the calibration of routine dosimetry systems under the actual conditions of use. Better understanding of the variations in influence quantities in industrial irradiators may be obtained by modeling or direct measurements and may provide improvements in the calibration of routine dosimetry system and reduction of the overall measurement uncertainty. (author)

  10. 16 CFR 500.7 - Net quantity of contents, method of expression.

    Science.gov (United States)

    2010-01-01

    ... expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical... consumers. The net quantity of contents statement shall be in terms of fluid measure if the commodity is liquid, or in terms of weight or mass if the commodity is solid, semi-solid, or viscous, or a mixture of...

  11. 19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

  12. A small quantity of sodium arsenite will kill large cull hardwoods

    Science.gov (United States)

    Francis M. Rushmore

    1956-01-01

    Although it is well known that sodium arsenite is an effective silvicide, forestry literature contains little information about the minimum quantities of this chemical that are required to kill large cull trees. Such information would be of value because if small quantities of a chemical will produce satisfactory results, small holes or frills in the tree will hold it...

  13. Calibration of personal dosemeters in terms of the ICRU operational quantities

    International Nuclear Information System (INIS)

    McDonald, J.C.; Hertel, N.E.

    1992-01-01

    The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosimeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The U.S. personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethylmethacrylate (PMMA) phantom; therefore it is necessary to relate the response of dosimeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosimeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors. (author)

  14. Calibration of personal dosemeters in terms of the ICRU operational quantities

    International Nuclear Information System (INIS)

    McDonald, J.C.; Hertel, N.E.

    1992-05-01

    The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosemeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The US personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethymethacrylate (PMMA) phantom, therefore it is necessary to relate the response of dosemeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosemeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors

  15. 76 FR 78141 - Pilot, Flight Instructor, and Pilot School Certification; Technical Amendment

    Science.gov (United States)

    2011-12-16

    ...-26661; Amdt. No. 61-129] RIN 2120-AI86 Pilot, Flight Instructor, and Pilot School Certification... requirements for pilots, flight instructors, ground instructors, and pilot schools. This document corrects an... a practical test for the issuance of a sport pilot certificate in a light-sport aircraft other than...

  16. 49 CFR 230.110 - Pilots.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Pilots. 230.110 Section 230.110 Transportation... and Equalizing System § 230.110 Pilots. (a) General provisions. Pilots shall be securely attached... clearance. The minimum clearance of pilot above the rail shall be 3 inches and the maximum clearance shall...

  17. Kvanefjeld refinery pilot plant operations

    International Nuclear Information System (INIS)

    Krebs, Damien; Furfaro, Domenic

    2016-01-01

    Greenland Minerals and Energy is a junior project development company which is listed on the Australian Stock Exchange (asx:GGG). It is developing the Kvanefjeld rare earth and uranium project located in the southern tip of Greenland. The project has completed a Feasibility Study and is currently in the permitting phase. Last year was a busy time for the company as it completed a Feasibility Study, a mining licence application (draft submitted in December 2015) and pilot plant operations. Beneficiation pilot plant operations were completed at GTK in Finland in April 2015. This pilot plant treated approximately 30 tonnes of ore to producing almost 2 tonnes of rare earth mineral concentrate. Later in the year a hydrometallurgical pilot plant was performed which mimicked the Refinery process. This pilot plant was performed at Outotec’s Pori Research laboratories in Finland from September till October 2015. The pilot plant treated approximately 200 kilograms of concentrate over 4 split operating campaigns. Each campaign was performed to focus on the performance of a specific part of the refinery flowsheet. This allowed for full operating focus on a single unit operation to ensure that it was operating correctly. The pilot plant operations were quite successful with no major issues with the flowsheet identified through continuous operation. Some fine tuning of conditions was required to ensure adequate removal of impurities was performed with recycle streams incorporated. Overall the leach extractions observed in the pilot plant exceeded the design assumptions in the Feasibility Study. These programs were partially funded by the EURARE program. The EURARE program aims to encourage the sustainable development of European based rare earth projects. This has the goal of allowing Europe to become less reliant on importation of these key raw materials. The professionalism and performance of both GTK and Outotec contributed significantly to the success of the pilot plant

  18. Priming a Pilot Implementation

    DEFF Research Database (Denmark)

    Hansen, Magnus Rotvit Perlt; Pedersen, Maria Ie

    2011-01-01

    Abstract. We report on the initial findings of an exploratory action research study about effects specifications using the systems development method Effects-driven IT development. It is part of a larger IS pilot implementation project conducted in the Danish healthcare sector. Through interviews...... and a workshop we have identified and specified effects that comprise the basis for an evaluation of the project between several organisational agents with diverse professional backgrounds. Gathering organisational participants at a workshop with a common goal of discussing and prioritizing a finished list...... of effects has proved to be a valuable approach to create mutual learning process amongst the participants and the facilitators of the workshop. The challenges we experienced during the effects specification process were to balance a dichotomous focus between on one hand the visions of the participants...

  19. Liverpool Telecare Pilot: case studies

    Directory of Open Access Journals (Sweden)

    Nigel Barnes

    2006-09-01

    Full Text Available Telecare services use information and communications technology (ICT to support the provision of care to people in their own homes. This paper describes a pilot telecare service employed by Liverpool (UK City Council to support a sample of their frail and elderly social services users. The pilot has been running for over two years and has been deployed for 21 individuals in Liverpool. In this paper we present the pilot system and provide real example cases which help to illustrate the benefits of such a system.

  20. Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

    International Nuclear Information System (INIS)

    Hagros, Annika

    2008-12-01

    The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

  1. Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Hagros, Annika (Sannio and Riekkola OY (Finland))

    2008-12-15

    The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

  2. Quantity and quality limit detritivore growth: mechanisms revealed by ecological stoichiometry and co-limitation theory.

    Science.gov (United States)

    Halvorson, Halvor M; Sperfeld, Erik; Evans-White, Michelle A

    2017-12-01

    Resource quantity and quality are fundamental bottom-up constraints on consumers. Best understood in autotroph-based systems, co-occurrence of these constraints may be common but remains poorly studied in detrital-based systems. Here, we used a laboratory growth experiment to test limitation of the detritivorous caddisfly larvae Pycnopsyche lepida across a concurrent gradient of oak litter quantity (food supply) and quality (phosphorus : carbon [P:C ratios]). Growth increased simultaneously with quantity and quality, indicating co-limitation across the resource gradients. We merged approaches of ecological stoichiometry and co-limitation theory, showing how co-limitation reflected shifts in C and P acquisition throughout homeostatic regulation. Increased growth was best explained by elevated consumption rates and improved P assimilation, which both increased with elevated quantity and quality. Notably, C assimilation efficiencies remained unchanged and achieved maximum 18% at low quantity despite pronounced C limitation. Detrital C recalcitrance and substantive post-assimilatory C losses probably set a minimum quantity threshold to achieve positive C balance. Above this threshold, greater quality enhanced larval growth probably by improving P assimilation toward P-intensive growth. We suggest this interplay of C and P acquisition contributes to detritivore co-limitation, highlighting quantity and quality as potential simultaneous bottom-up controls in detrital-based ecosystems, including under anthropogenic change like nutrient enrichment. © 2017 by the Ecological Society of America.

  3. Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

    KAUST Repository

    Jing, Wei

    2016-12-01

    Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

  4. Waste Isolation Pilot Plant Overview

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, Douglas James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-27

    The mission of Waste Isolation Pilot Plant (WIPP) is to demonstrate the safe, environmentally sound, cost effective, permanent disposal of Transuranic (TRU) waste left from production of nuclear weapons.

  5. Rockfish Pilot Permit Program (RPP)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Rockfish Pilot Program was a five-year project that allowed harvesters to form voluntary cooperatives and receive an exclusive harvest privilege for groundfish...

  6. US Daily Pilot Balloon Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Pilot Balloon observational forms for the United States. Taken by Weather Bureau and U.S. Army observers. Period of record 1918-1960. Records scanned from the NCDC...

  7. WIPP: Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    1984-01-01

    The following aspects of the Waste Isolation Pilot Plant are discussed briefly: history and site selection; salt as a disposal medium; transporting waste materials; early key events; impacts on New Mexico; project organization; and site certification profile

  8. Vertebral pain in helicopter pilots

    Science.gov (United States)

    Auffret, R.; Delahaye, R. P.; Metges, P. J.; VICENS

    1980-01-01

    Pathological forms of spinal pain engendered by piloting helicopters were clinically studied. Lumbalgia and pathology of the dorsal and cervical spine are discussed along with their clinical and radiological signs and origins.

  9. Non-Noether Conserved Quantity for Relativistic Nonholonomic System with Variable Mass

    International Nuclear Information System (INIS)

    Qiao Yongfen; Li Renjie; Ma Yongsheng

    2005-01-01

    Using form invariance under special infinitesimal transformations in which time is not variable, the non-Noether conserved quantity of the relativistic nonholonomic system with variable mass is studied. The differential equations of motion of the system are established. The definition and criterion of the form invariance of the system under infinitesimal transformations are studied. The necessary and sufficient condition under which the form invariance is a Lie symmetry is given. The condition under which the form invariance can be led to a non-Noether conserved quantity and the form of the conserved quantity are obtained. Finally, an example is given to illustrate the application of the result.

  10. EFFECT OF SALES PROMOTION SCHEMES ON PURCHASE QUANTITY: A STUDY OF MALAYSIAN CONSUMERS

    Directory of Open Access Journals (Sweden)

    Hawa JALLOW

    2016-11-01

    Full Text Available The research aims to study the effect of sales promotion on the purchase quantity and recommend sales promotional means and methods that could improve sales for retail sector in Malaysia. The impact of coupons, bonus packages, premiums, free samples and price discount is measured on purchase quantity of Malaysian retail consumers. Empirical data is gathered from 150 respondents using self-administered questionnaire and analyzed using correlation and regression analysis to examine the relationship between variables. The findings of the study reveal that all independent variables influences purchase quantity positively and significantly while free samples and price discounts are most influential factors for Malaysian market.

  11. The estimation of differential counting measurements of possitive quantities with relatively large statistical errors

    International Nuclear Information System (INIS)

    Vincent, C.H.

    1982-01-01

    Bayes' principle is applied to the differential counting measurement of a positive quantity in which the statistical errors are not necessarily small in relation to the true value of the quantity. The methods of estimation derived are found to give consistent results and to avoid the anomalous negative estimates sometimes obtained by conventional methods. One of the methods given provides a simple means of deriving the required estimates from conventionally presented results and appears to have wide potential applications. Both methods provide the actual posterior probability distribution of the quantity to be measured. A particularly important potential application is the correction of counts on low radioacitvity samples for background. (orig.)

  12. Coordinated Lot-sizing and Dynamic Prizing under a Supplier All-units Quantity Discount

    Directory of Open Access Journals (Sweden)

    Sandra Transchel

    2008-05-01

    Full Text Available We consider an economic order quantity model where the supplier offers an all-units quantity discount and a price sensitive customer demand. We compare a decentralized decision framework where selling price and replenishment policy are determined independently to simultaneous decision making. Constant and dynamic pricing are distinguished. We derive structural properties and develop algorithms that determine the optimal pricing and replenishment policy and show how quantity discounts not only influence the purchasing strategy but also the pricing policy. A sensitivity analysis indicates the impact of the fixed-holding cost ratio, the discount policy, and the customers' price sensitivity on the optimal decisions.

  13. Validity of the concept of absorbed dose as a physical quantity

    International Nuclear Information System (INIS)

    Tada, Jun-Ichiro; Katoh, Kazuaki.

    1995-01-01

    The concept of the 'absorbed dose' of ionizing radiation is scrutinized from physical point of view. It is shown that the concept and definition of the quantity in the ICRU system is disqualified as a physical quantity and the absorbed dose can not always be a 'measure of cause' in describing causality relation between radiation and effects on matter. The current absorbed dose depends even on the energy that have already been brought out from the matter, contrary to the intention of introducing the quantity. Trials to remove these difficulties are made. However, it is also shown there still exists an essential problem that cannot be solved by improving the formulation. (author)

  14. QUANTITY DISCOUNTS IN SUPPLIER SELECTION PROBLEM BY USE OF FUZZY MULTI-CRITERIA PROGRAMMING

    Directory of Open Access Journals (Sweden)

    Tunjo Perić

    2011-02-01

    Full Text Available Supplier selection in supply chain is a multi-criteria problem that involves a number of quantitative and qualitative factors. This paper deals with a concrete problem of flour purchase by a company that manufactures bakery products and the purchasing price of flour depends on the quantity ordered. The criteria for supplier selection and quantities supplied by individual suppliers are: purchase costs, product quality and reliability of suppliers. The problem is solved using a model that combines revised weighting method and fuzzy multi-criteria linear programming (FMCLP. The paper highlights the efficiency of the proposed methodology in conditions when purchasing prices depend on order quantities.

  15. Evaluación de las propiedades psicométricas del cuestionario de Detección de Malestar Emocional (DME en pacientes oncológicos Assessment of the psychometric properties of the Detection of Emotional Distress Scale in cancer patients

    Directory of Open Access Journals (Sweden)

    Joaquín T. Limonero

    2012-04-01

    Full Text Available Objetivos: Con el fin de valorar y aliviar el malestar emocional al final de la vida, se necesitan instrumentos de cribado sencillos, de fácil uso por los sanitarios y comprensibles por los enfermos. En el presente estudio multicéntrico se analiza la utilidad clínica del cuestionario de Detección del Malestar Emocional (DME en enfermos hospitalizados con cáncer avanzado. Métodos: Para determinar las propiedades psicométricas de la escala se administró, a la vez que otros instrumentos y procedimientos, a 105 pacientes con enfermedad oncológica avanzada ingresados en unidades de cuidados paliativos de cinco hospitales de Cataluña. Resultados: Se observó que el 58,3% presentaba malestar emocional moderado o muy intenso, similar al objetivado con otras escalas, como el termómetro emocional. El análisis estadístico de las curvas ROC sugiere que el punto de corte para la detección de malestar emocional que muestra el DME equivale a una puntuación > 9 puntos, con una sensibilidad y una especificidad superiores al 75%. Conclusiones: El DME es útil y de fácil manejo para la identificación del malestar emocional en los enfermos oncológicos avanzados ingresados en unidades de cuidados paliativos. Se sugiere que esta escala también se podría aplicar a otros enfermos y ámbitos de la atención sanitaria, por ejemplo la atención domiciliaria o la atención primaria en enfermos crónicos.Objective: To evaluate and alleviate the emotional distress suffered by advanced cancer patients, simple screening methods that can be easily used by health staff and easily understood by patients are required. The objective of this multicenter study was to analyze the psychometric properties and clinical utility of the Detection of Emotional Distress (DED scale in advanced cancer patients attending a palliative care unit. Methods: The DED scale was administered to 105 advanced cancer patients attended in five palliative care units in Catalonia (Spain

  16. Piloted Aircraft Environment Simulation Techniques

    Science.gov (United States)

    1978-04-01

    raS’I.Al. lIIf~iiI~.1 labL. lot. Rolmotion -oft. skylicav - ow d Roll rMotion -oft Skylicape - Off Fig 6 a A Effect of roll motion and akyscape, an msatwntn...greater realism and pilot involvement than ground based simu- lation, it still lacks some of the pilot motivating factors of actual combat. Flight

  17. Active Job Monitoring in Pilots

    Science.gov (United States)

    Kuehn, Eileen; Fischer, Max; Giffels, Manuel; Jung, Christopher; Petzold, Andreas

    2015-12-01

    Recent developments in high energy physics (HEP) including multi-core jobs and multi-core pilots require data centres to gain a deep understanding of the system to monitor, design, and upgrade computing clusters. Networking is a critical component. Especially the increased usage of data federations, for example in diskless computing centres or as a fallback solution, relies on WAN connectivity and availability. The specific demands of different experiments and communities, but also the need for identification of misbehaving batch jobs, requires an active monitoring. Existing monitoring tools are not capable of measuring fine-grained information at batch job level. This complicates network-aware scheduling and optimisations. In addition, pilots add another layer of abstraction. They behave like batch systems themselves by managing and executing payloads of jobs internally. The number of real jobs being executed is unknown, as the original batch system has no access to internal information about the scheduling process inside the pilots. Therefore, the comparability of jobs and pilots for predicting run-time behaviour or network performance cannot be ensured. Hence, identifying the actual payload is important. At the GridKa Tier 1 centre a specific tool is in use that allows the monitoring of network traffic information at batch job level. This contribution presents the current monitoring approach and discusses recent efforts and importance to identify pilots and their substructures inside the batch system. It will also show how to determine monitoring data of specific jobs from identified pilots. Finally, the approach is evaluated.

  18. Study of dimensionless quantities to analyse front and rear wall of ...

    Indian Academy of Sciences (India)

    hydrodynamic quantities describe the mechanism behind flow pattern present in .... beam is focused into a small spot adjustable approximately 0.1 to 0.8 mm in ... moves, the liquefied metal around the 'keyhole' flows back in, solidifying and.

  19. The Effect of Quantity, Quality and Timing of Headquarters-Initiated Knowledge Flows on Subsidiary Performance

    DEFF Research Database (Denmark)

    Tran, Yen; Mahnke, Volker; Ambos, Björn

    2010-01-01

    quality/performance relationship and a curvilinear quantity/performance relationship, indicating that too much knowledge sharing can be detrimental to the receiving subsidiary. Most importantly, we show that the timing of a knowledge flow significantly affects subsidiary sales performance....

  20. The effect of vial type and cocktail quantity on tritium measurement in LSC

    International Nuclear Information System (INIS)

    Chen Zhilin; Xing Shixiong; Wang Heyi; Chang Ruimin; Wu Guanyin; Zhou Yinhang

    2010-01-01

    The effect of sample vial type and cocktail quantity on tritium measurement in liquid scintillation counting is studied in this paper. With both high and low level tritium samples, glass vials allow higher counting rates than plastic vials do. We also present detailed analysis of the way to obtain the optimal counting condition by dispensing different quantity of cocktail into sample vials. Results indicate that the optimal counting condition has little relationship with tritium concentration in the sample. The main factor which influences the counting is the quantity of cocktail added into samples. Figure of merit is employed to access the results, which increases as the quantity of cocktail increasing. But when the ratio of cocktail and sample reaches 2.0, increase of ratio makes little contribution to the counts, and the disintegrations per minute comes nearly to be a constant.

  1. Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

    KAUST Repository

    Jing, Wei; Wu, Zengyang; Roberts, William L.; Fang, Tiegang

    2016-01-01

    Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement

  2. 3D facial expression recognition based on histograms of surface differential quantities

    KAUST Repository

    Li, Huibin; Morvan, Jean-Marie; Chen, Liming

    2011-01-01

    . To characterize shape information of the local neighborhood of facial landmarks, we calculate the weighted statistical distributions of surface differential quantities, including histogram of mesh gradient (HoG) and histogram of shape index (HoS). Normal cycle

  3. Optimizing basin-scale coupled water quantity and water quality management with stochastic dynamic programming

    DEFF Research Database (Denmark)

    Davidsen, Claus; Liu, Suxia; Mo, Xingguo

    2015-01-01

    Few studies address water quality in hydro-economic models, which often focus primarily on optimal allocation of water quantities. Water quality and water quantity are closely coupled, and optimal management with focus solely on either quantity or quality may cause large costs in terms of the oth......-er component. In this study, we couple water quality and water quantity in a joint hydro-economic catchment-scale optimization problem. Stochastic dynamic programming (SDP) is used to minimize the basin-wide total costs arising from water allocation, water curtailment and water treatment. The simple water...... quality module can handle conservative pollutants, first order depletion and non-linear reactions. For demonstration purposes, we model pollutant releases as biochemical oxygen demand (BOD) and use the Streeter-Phelps equation for oxygen deficit to compute the resulting min-imum dissolved oxygen...

  4. Effects of herbivore exclosures on variation in quality and quantity of ...

    African Journals Online (AJOL)

    Effects of herbivore exclosures on variation in quality and quantity of plants among ... commercial and game) and among habitat types (open savanna, rocky and pan) in a semiarid savanna in South Africa. ... AJOL African Journals Online.

  5. Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

    Directory of Open Access Journals (Sweden)

    Gaku Fukunaga

    Full Text Available The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

  6. Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

    Science.gov (United States)

    Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

    2016-01-01

    The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

  7. By Default: The Effect of Prepopulated Prescription Quantities on Opioid Prescribing in the Emergency Department.

    Science.gov (United States)

    Santistevan, Jamie R; Sharp, Brian R; Hamedani, Azita G; Fruhan, Scott; Lee, Andrew W; Patterson, Brian W

    2018-03-01

    Opioid prescribing patterns have come under increasing scrutiny with the recent rise in opioid prescriptions, opioid misuse and abuse, and opioid-related adverse events. To date, there have been limited studies on the effect of default tablet quantities as part of emergency department (ED) electronic order entry. Our goal was to evaluate opioid prescribing patterns before and after the removal of a default quantity of 20 tablets from ED electronic order entry. We performed a retrospective observational study at a single academic, urban ED with 58,000 annual visits. We identified all adult patients (18 years or older) seen in the ED and discharged home with prescriptions for tablet forms of hydrocodone and oxycodone (including mixed formulations with acetaminophen). We compared the quantity of tablets prescribed per opioid prescription 12 months before and 10 months after the electronic order-entry prescription default quantity of 20 tablets was removed and replaced with no default quantity. No specific messaging was given to providers, to avoid influencing prescribing patterns. We used two-sample Wilcoxon rank-sum test, two-sample test of proportions, and Pearson's chi-squared tests where appropriate for statistical analysis. A total of 4,104 adult patients received discharge prescriptions for opioids in the pre-intervention period (151.6 prescriptions per 1,000 discharged adult patients), and 2,464 post-intervention (106.69 prescriptions per 1,000 discharged adult patients). The median quantity of opioid tablets prescribed decreased from 20 (interquartile ration [IQR] 10-20) to 15 (IQR 10-20) (pdefault quantity. While the most frequent quantity of tablets received in both groups was 20 tablets, the proportion of patients who received prescriptions on discharge that contained 20 tablets decreased from 0.5 (95% confidence interval [CI] [0.48-0.52]) to 0.23 (95% CI [0.21-0.24]) (pdefault quantity removal. Although the median number of tablets differed significantly

  8. Unified Symmetry and Conserved Quantities of Mechanical System in Phase Space

    International Nuclear Information System (INIS)

    Fang Jianhui; Ding Ning; Wang Peng

    2006-01-01

    In this paper, a new symmetry and its conserved quantities of a mechanical system in phase space are studied. The definition of this new symmetry, i.e., a unified one is presented, and the criterion of this symmetry is also given. The Noether, the generalized Hojman and the Mei conserved quantities of the unified symmetry of the system are obtained. The unified symmetry contains the Noether, the Lie and the Mei symmetries, and has more generalized significance.

  9. Quality and quantity: the role of social interactions in individual health

    OpenAIRE

    Damiano, Fiorillo; Fabio, Sabatini

    2011-01-01

    The public health literature focusing on the detrimental effects of social isolation has shown that the quantity of social connections is positively correlated with individual health. Drawing on pooled cross-sectional data, we test this hypothesis on a representative sample of the Italian population. Our findings show that, besides the quantity of interactions, it is their quality – as measured by subjective satisfaction derived from relationships with friends – that works as the best pre...

  10. Water Quality and Quantity in Intermittent and Continuous Piped Water Supplies in Hubli-Dharwad, India

    OpenAIRE

    Kumpel, Emily Katherine

    2013-01-01

    In at least 45 low- and middle-income countries, piped water systems deliver water for limited durations. Few data are available of the impact of intermittent water supply (IWS) on the water quality and quantity delivered to households. This thesis examines the impact of intermittently supplied piped water on the quality and quantity of water delivered to residential taps in Hubli-Dharwad, India, when compared to continuous piped water supply. A framework for understanding the pathways throug...

  11. The effects of quantity and depth of processing on children's time perception.

    Science.gov (United States)

    Arlin, M

    1986-08-01

    Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

  12. Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

    Science.gov (United States)

    Roşu, M. M.; Tarbă, C. I.; Neagu, C.

    2016-11-01

    The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

  13. Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

    International Nuclear Information System (INIS)

    Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun; Sung, Nak-Hoon; Jung, Seung Hyuk

    2016-01-01

    Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis

  14. Would more social partners leads to enhanced health? The paradox between quantity and quality.

    Science.gov (United States)

    Xing, Cai; Zhang, Xin; Cheng, Sheung-Tak

    2017-09-01

    In the current investigation, we examined the association between social network composition (SNC) and mental health, as well as whether quantity and quality of social network could influence mental health differently. The social network quantity and quality of 345 middle-aged and older Chinese adults were measured by the Social Convoy Questionnaire. The Chinese version of the Medical Outcome Studies 36-item Short-Form Health Survey (SF-36) was used to assess mental health while controlling for physical health. It was found that both quantity and quality of social network were associated with mental health, and more specifically that (1) quantity of peripheral partners (PP) was positively associated with mental health; (2) quality of emotionally close social partners (ECSP) influenced mental health the most; and (3) paradoxically, the effect of ECSP quality on mental health depended on quantity of ECSP, that is, participants with more ECSP showed a stronger association between ECSP quality and mental health. The findings replicated and extended previous studies on SNC and suggested that structure/quantity and quality of SNC were both important for mental health. © 2017 The Institute of Psychology, Chinese Academy of Sciences and John Wiley & Sons Australia, Ltd.

  15. Detection Dynamics Of Nitrogen Based Explosive Quantities In Selected Cylindrical Containers

    Directory of Open Access Journals (Sweden)

    Ngusha Tavershima Almighty

    2017-12-01

    Full Text Available An experimental set up for examining the variation of detection intensity with explosive quantity has been studied. Containers made from ceramic carbon steel wood and HDPE were filled with explosive masses ranging from 10 kg to 500 kg and irradiated by a 14.1 MeV point isotropic neutron source. The resulting gamma photons were analyzed for their C N and O composition and the sum computed to yield a quantity known as the material quotient MQ. Examination of MQ values indicates an initial increase in detection intensity with increasing explosive quantity. Saturation is however reached at an explosive quantity of about 25kg where detection intensity reduces with further increase in explosive quantity. Effects of variation in explosive quantity appeared to be more pronounced for explosives contained in HDPE and wooden containers and least pronounced for those in steel containers. Source-detector configuration was identified as a major factor affecting effective detection of large masses of explosives.

  16. Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun [KHNP CRI, Daejeon (Korea, Republic of); Sung, Nak-Hoon; Jung, Seung Hyuk [KONES Corp., Seoul (Korea, Republic of)

    2016-10-15

    Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis.

  17. Toronto hybrid taxi pilot

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, M. [CrossChasm Technologies, Cambridge, ON (Canada); Marans, B. [Toronto Atmospheric Fund, ON (Canada)

    2009-10-15

    This paper provided details of a hybrid taxi pilot program conducted to compare the on-road performance of Toyota Camry hybrid vehicles against conventional vehicles over a 1-year period in order to determine the business case and air emission reductions associated with the use of hybrid taxi cabs. Over 750,000 km worth of fuel consumption was captured from 10 Toyota Camry hybrids, a Toyota Prius, and 5 non-hybrid Camry vehicles over an 18-month period. The average real world fuel consumption for the taxis demonstrated that the Toyota Prius has the lowest cost of ownership, while the non-hybrid Camry has the highest cost of ownership. Carbon dioxide (CO{sub 2}) reductions associated with the 10 Camry hybrid taxis were calculated at 236 tonnes over a 7-year taxi service life. Results suggested that the conversion of Toronto's 5680 taxis would yield annual CO{sub 2} emission reductions of over 19,000 tonnes. All hybrid purchasers identified themselves as highly likely to purchase a hybrid again. 5 tabs., 9 figs.

  18. Fitzmaurice Voicework Pilot Study.

    Science.gov (United States)

    Watson, Lynn; Nayak, Sadhana

    2015-11-01

    A repeated-measures pilot study was used to investigate acoustic changes in the voices of participants in a Fitzmaurice Voicework (FV) teacher certification program. Maximum phonation time (MPT) was also measured. Eleven participants with no reported voice problems were studied. Pretraining and posttraining recordings were made of each participant. Measures of MPT were made, and the recordings were analyzed for jitter, shimmer, and noise-to-harmonics ratio (NHR). The measure of effect size for MPT was moderate, and there was an overall increase in MPT from pretraining to posttraining, with 70% of participants showing an increase in MPT. The measure of effect sizes for jitter, shimmer, and NHR were small, with measurements showing no significant changes from pretraining to posttraining. There were indications that FV training may have positive outcomes for actors and professional voice users, particularly in increasing MPT. Further studies with larger subject groups are needed to investigate the significance of the increase in MPT noted in this study and to test whether FV training can help to lower rates of shimmer and jitter. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

  19. Toronto hybrid taxi pilot

    International Nuclear Information System (INIS)

    Stevens, M.; Marans, B.

    2009-10-01

    This paper provided details of a hybrid taxi pilot program conducted to compare the on-road performance of Toyota Camry hybrid vehicles against conventional vehicles over a 1-year period in order to determine the business case and air emission reductions associated with the use of hybrid taxi cabs. Over 750,000 km worth of fuel consumption was captured from 10 Toyota Camry hybrids, a Toyota Prius, and 5 non-hybrid Camry vehicles over an 18-month period. The average real world fuel consumption for the taxis demonstrated that the Toyota Prius has the lowest cost of ownership, while the non-hybrid Camry has the highest cost of ownership. Carbon dioxide (CO 2 ) reductions associated with the 10 Camry hybrid taxis were calculated at 236 tonnes over a 7-year taxi service life. Results suggested that the conversion of Toronto's 5680 taxis would yield annual CO 2 emission reductions of over 19,000 tonnes. All hybrid purchasers identified themselves as highly likely to purchase a hybrid again. 5 tabs., 9 figs.

  20. The Marcoule pilot plant

    International Nuclear Information System (INIS)

    Faugeras, P.; Calame Longjean, A.; Le Bouhellec, J.; Revol, G.

    1986-06-01

    The Marcoule spent fuel reprocessing pilot facility was built in 1960-1961 for extended testing of the PUREX process with various types of fuel under conditions similar to those encountered in a production plant. Extensive modification work was undertaken on the facility in 1983 in the scope of the TOR project, designed with the following objectives: - increase the throughput capacity to at least 5 metric tons of PHENIX equivalent fuel per year, - extend equipment and process R and D capability, - improve job safety by maximum use of remote handling facilities, - maximize waste conditioning treatments to produce waste forms suitable for direct storage, - provide a true industrial process demonstration in continuous operation under centralized control using computerized procedures. The redesigned plant is scheduled to begin operation during the second half of 1986. The proximity of the Industrial Prototypes Service and the ATALANTE radiochemical research laboratory scheduled to begin operation in 1990, will provide a synergistic environment in which R and D program may be carried out under exceptional conditions

  1. Roll paper pilot. [mathematical model for predicting pilot rating of aircraft in roll task

    Science.gov (United States)

    Naylor, F. R.; Dillow, J. D.; Hannen, R. A.

    1973-01-01

    A mathematical model for predicting the pilot rating of an aircraft in a roll task is described. The model includes: (1) the lateral-directional aircraft equations of motion; (2) a stochastic gust model; (3) a pilot model with two free parameters; and (4) a pilot rating expression that is a function of rms roll angle and the pilot lead time constant. The pilot gain and lead time constant are selected to minimize the pilot rating expression. The pilot parameters are then adjusted to provide a 20% stability margin and the adjusted pilot parameters are used to compute a roll paper pilot rating of the aircraft/gust configuration. The roll paper pilot rating was computed for 25 aircraft/gust configurations. A range of actual ratings from 2 to 9 were encountered and the roll paper pilot ratings agree quite well with the actual ratings. In addition there is good correlation between predicted and measured rms roll angle.

  2. A Comparative Study of Face Milling of D2 Steel Using Al2O3 Based Nanofluid Minimum Quantity Lubrication and Minimum Quantity Lubrication

    Directory of Open Access Journals (Sweden)

    Muhammad Ahsan Ul Haq

    2018-03-01

    Full Text Available This study aims to investigate the effects of process parameters feed, depth of cut and flow rate, on the temperature during face milling of the D2 tool steel under two different lubricant conditions, Minimum Quantity Lubrication (MQL and Nanofluid Minimum Quantity Lubrication (NFMQL. Distilled water with the flow rate range 200-400 ml/hr was used in MQL. 2% by weight concentration of Al2O3 nanoparticles with distilled water as the base fluid used as NFMQL with same flow rate. Response surface methodology RSM central composite design CCD was used to design experiment run, modeling, and analysis. ANOVA was used for the adequacy and validation of the system. The comparison shows that NFMQL condition reduced more temperature during machining.

  3. Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

    Science.gov (United States)

    2013-01-01

    Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

  4. Association between work-family conflict and smoking quantity among daily smokers.

    Science.gov (United States)

    Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

    2013-11-01

    Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

  5. Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

    Science.gov (United States)

    Ivanov, Kamen G.; Pavlis, Nikolaos K.; Petrushev, Pencho

    2017-12-01

    Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly ζ , gravity anomaly Δ g , gravity disturbance δ g , north-south deflection of the vertical ξ , east-west deflection of the vertical η , and the second radial derivative T_{rr} of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed 10^{-6} and the memory (RAM) use is 9.3 GB.

  6. 14 CFR 121.437 - Pilot qualification: Certificates required.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Pilot qualification: Certificates required... Pilot qualification: Certificates required. (a) No pilot may act as pilot in command of an aircraft (or... pilots) unless he holds an airline transport pilot certificate and an appropriate type rating for that...

  7. 49 CFR 381.400 - What is a pilot program?

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false What is a pilot program? 381.400 Section 381.400... PILOT PROGRAMS Initiation of Pilot Programs § 381.400 What is a pilot program? (a) A pilot program is a... that would be subject to the regulations. (b) During a pilot program, the participants would be given...

  8. 75 FR 53007 - Gulf Opportunity Pilot Loan Program (GO Loan Pilot)

    Science.gov (United States)

    2010-08-30

    ... SMALL BUSINESS ADMINISTRATION Gulf Opportunity Pilot Loan Program (GO Loan Pilot) AGENCY: U.S...'s GO Loan Pilot until September 30, 2011. Due to the scope and magnitude of the devastation to... streamlined and centralized loan processing available through the GO Loan Pilot to small businesses in the...

  9. 77 FR 61721 - Pilot, Flight Instructor, and Pilot School Certification; Technical Amendment

    Science.gov (United States)

    2012-10-11

    ...-26661; Amdt. No. 61-129A] RIN 2120-AI86 Pilot, Flight Instructor, and Pilot School Certification... revise the training, qualification, certification, and operating requirements for pilots, flight instructors, ground instructors, and pilot schools. A portion of the codified text was inadvertently deleted...

  10. 76 FR 60960 - Gulf Opportunity Pilot Loan Program (GO Loan Pilot)

    Science.gov (United States)

    2011-09-30

    ... SMALL BUSINESS ADMINISTRATION Gulf Opportunity Pilot Loan Program (GO Loan Pilot) AGENCY: U.S.... SUMMARY: This notice announces the extension of SBA's GO Loan Pilot, with modifications, until December 31... processing available through the GO Loan Pilot to small businesses in the eligible parishes/counties through...

  11. Wood torrefaction. Pilot tests and utilisation prospects

    Energy Technology Data Exchange (ETDEWEB)

    Wilen, C.; Jukola, P.; Jarvinen, T.; Sipila, K. [VTT Technical Reseach Centre of Finland, Espoo (Finland); Verhoeff, F.; Kiel, J. [Energy research Centre of the Netherlands, LE Petten (Netherlands)

    2013-09-15

    The research project 'Torrefaction of woody biomasses as energy carriers for the European markets' was carried out within the Tekes BioRefine programme in 2010-2012 and was coordinated by VTT. The main objective of the project was to create a discussion platform and collate basic information for the Finnish industrial stakeholders involved in developing torrefaction technology or planning to include torrefied biomass in their fuel supply for energy production. Given the availability of torrefaction pilot facilities in Europe, it was decided at an early phase of the national torrefaction research project not to build and operate separate pilot equipment, and thus save time and money. Experimental research was conducted in cooperation with ECN, The Netherlands. Finnish wood chips and crushed forest residue were tested at different torrefaction temperatures in the PATRIG torrefaction test rig with great success, and large quantities of torrefied wood chips and pellets were produced. CFD simulation work was carried out at VTT to investigate the feasibility of torrefied fuels to replace part of the coal. From the combustion point of view it seems feasible to replace coal by torrefied wood biomass with shares up to 50% by weight. Basic, small-scale experiments were carried out to compare torrefied wood pellets with conventional wood and straw pellets with regard to their handling and storage properties. The experiments showed that the torrefied pellets are clearly more hydrophobic than wood and straw pellets and do not disintegrate completely on exposure to water. A study on dust explosion and self-ignition characteristics indicated that the torrefied dust does not differ significantly from the normal biomass dust, but is clearly more reactive than coal dust. Commercial development of torrefaction is currently in its early phase. The current general view is that most of the demonstration plants have technical problems, which have delayed their commercial

  12. WIPP [Waste Isolation Pilot Plant] test phase plan: Performance assessment

    International Nuclear Information System (INIS)

    1990-04-01

    The U.S. Department of Energy (DOE) is responsible for managing the disposition of transuranic (TRU) wastes resulting from nuclear weapons production activities of the United States. These wastes are currently stored nationwide at several of the DOE's waste generating/storage sites. The goal is to eliminate interim waste storage and achieve environmentally and institutionally acceptable permanent disposal of these TRU wastes. The Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico is being considered as a disposal facility for these TRU wastes. This document describes the first of the following two major programs planned for the Test Phase of WIPP: Performance Assessment -- determination of the long-term performance of the WIPP disposal system in accordance with the requirements of the EPA Standard; and Operations Demonstration -- evaluation of the safety and effectiveness of the DOE TRU waste management system's ability to emplace design throughput quantities of TRU waste in the WIPP underground facility. 120 refs., 19 figs., 8 tabs

  13. Quality Versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches

    Directory of Open Access Journals (Sweden)

    Nugent Frank J.

    2017-06-01

    Full Text Available The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches’ perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches’ perspective which was not currently available in the research literature.

  14. Management of Water Quantity and Quality Based on Copula for a Tributary to Miyun Reservoir, Beijing

    Science.gov (United States)

    Zang, N.; Wang, X.; Liang, P.

    2017-12-01

    Due to the complex mutual influence between water quantity and water quality of river, it is difficult to reflect the actual characters of the tributaries to reservoir. In this study, the acceptable marginal probability distributions for water quantity and quality of reservoir inflow were calculated. A bivariate Archimedean copula was further applied to establish the joint distribution function of them. Then multiple combination scenarios of water quantity and water quality were designed to analyze their coexistence relationship and reservoir management strategies. Taking Bai river, an important tributary into the Miyun Reservoir, as a study case. The results showed that it is feasible to apply Frank copula function to describe the jointed distribution function of water quality and water quantity for Bai river. Furthermore, the monitoring of TP concentration needs to be strengthen in Bai river. This methodology can be extended to larger dimensions and is transferable to other reservoirs via establishment of models with relevant data for a particular area. Our findings help better analyzing the coexistence relationship and influence degree of the water quantity and quality of the tributary to reservoir for the purpose of water resources protection.

  15. Quality versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches.

    Science.gov (United States)

    Nugent, Frank J; Comyns, Thomas M; Warrington, Giles D

    2017-06-01

    The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches' perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches' perspective which was not currently available in the research literature.

  16. 76 FR 56262 - Community Advantage Pilot Program

    Science.gov (United States)

    2011-09-12

    ... SMALL BUSINESS ADMINISTRATION [Docket No. SBA 2011-0003] Community Advantage Pilot Program AGENCY: U.S. Small Business Administration (SBA). ACTION: Notice of change to Community Advantage Pilot... Community Advantage Pilot Program. In that notice, SBA modified or waived as appropriate certain regulations...

  17. 77 FR 58208 - Airport Privatization Pilot Program

    Science.gov (United States)

    2012-09-19

    ... Privatization Pilot Program AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of receipt of... International Airport, San Juan, Puerto Rico (SJU) in the Airport Privatization Pilot Program and has determined....S.C. Section 47134 establishes an airport privatization pilot program and authorizes the Department...

  18. 75 FR 473 - Community Express Pilot Program

    Science.gov (United States)

    2010-01-05

    ... SMALL BUSINESS ADMINISTRATION Community Express Pilot Program AGENCY: U.S. Small Business Administration (SBA). ACTION: Notice of extension of the Community Express Pilot Program. SUMMARY: This notice extends the Community Express Pilot Program in its current form through December 31, 2010. Based upon the...

  19. 75 FR 80561 - Community Express Pilot Program

    Science.gov (United States)

    2010-12-22

    ... SMALL BUSINESS ADMINISTRATION Community Express Pilot Program AGENCY: U.S. Small Business Administration (SBA). ACTION: Notice of short-term extension and termination of the Community Express Pilot Program. SUMMARY: This notice announces the termination of the Community Express Pilot Program following a...

  20. 75 FR 68018 - Airport Privatization Pilot Program

    Science.gov (United States)

    2010-11-04

    ... Privatization Pilot Program AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of Receipt and... preliminary application for participation in the airport privatization pilot program received under 49 U.S.C... final application to the FAA for exemption under the pilot program. 49 U.S.C. Section 47134 establishes...

  1. 75 FR 39091 - Airport Privatization Pilot Program

    Science.gov (United States)

    2010-07-07

    ... Privatization Pilot Program AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of Receipt and... application for participation in the airport privatization pilot program received under 49 U.S.C. 47134. The... application to the FAA for exemption under the pilot program. 49 U.S.C. 47134 establishes an airport...

  2. 78 FR 50399 - Spectrum Monitoring Pilot Program

    Science.gov (United States)

    2013-08-19

    ... 130809703-3703-01] RIN 0660-XC007 Spectrum Monitoring Pilot Program AGENCY: National Telecommunications and... National Telecommunications and Information Administration (NTIA) to design and conduct a pilot program to... investment for a two-year pilot program to determine the benefits of an automated spectrum measurement and...

  3. 28 CFR 11.2 - Pilot program.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Pilot program. 11.2 Section 11.2 Judicial... Pilot program. The Assistant Attorney General for Administration, in consultation with the Executive Office for United States Attorneys, shall designate the districts that will participate in the pilot...

  4. 75 FR 1591 - Green Technology Pilot Program

    Science.gov (United States)

    2010-01-12

    ... DEPARTMENT OF COMMERCE Patent and Trademark Office Green Technology Pilot Program ACTION: Proposed... methods: E-mail: [email protected] . Include A0651-0062 Green Technology Pilot Program [email protected] in... (USPTO) is implementing a streamlined examination pilot program for patent applications pertaining to...

  5. 75 FR 39090 - Airport Privatization Pilot Program

    Science.gov (United States)

    2010-07-07

    ... Privatization Pilot Program AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of Receipt and... pilot program received under 49 U.S.C. Section 47134. The preliminary application is accepted for review... operator, negotiate an agreement and submit a final application to the FAA for exemption under the pilot...

  6. 48 CFR 212.7002 - Pilot program.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Pilot program. 212.7002... OF DEFENSE ACQUISITION PLANNING ACQUISITION OF COMMERCIAL ITEMS Pilot Program for Transition to Follow-On Contracting After Use of Other Transaction Authority 212.7002 Pilot program. ...

  7. 75 FR 64692 - Green Technology Pilot Program

    Science.gov (United States)

    2010-10-20

    ... DEPARTMENT OF COMMERCE Patent and Trademark Office Green Technology Pilot Program ACTION: Proposed...- 0062 Green Technology Pilot Program comment'' in the subject line of the message. Fax: 571-273-0112... United States Patent and Trademark Office (USPTO) implemented a pilot program on December 8, 2009, that...

  8. 46 CFR 15.812 - Pilots.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Pilots. 15.812 Section 15.812 Shipping COAST GUARD....812 Pilots. (a) Except as specified in paragraph (f) of this section, the following vessels, not... direction and control of an individual qualified to serve as pilot under paragraph (b) or (c) of this...

  9. 7 CFR 1955.132 - Pilot projects.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 14 2010-01-01 2009-01-01 true Pilot projects. 1955.132 Section 1955.132 Agriculture... REGULATIONS (CONTINUED) PROPERTY MANAGEMENT Disposal of Inventory Property General § 1955.132 Pilot projects. FmHA or its successor agency under Public Law 103-354 may conduct pilot projects to test policies and...

  10. Ergonomic evaluation of pilot oxygen mask designs

    NARCIS (Netherlands)

    Lee, W.; Yang, Xiaopeng; Jung, Daehan; Park, Seikwon; Kim, Heeeun; You, Heecheon

    2018-01-01

    A revised pilot oxygen mask design was developed for better fit to the Korean Air Force pilots’ faces. The present study compared an existing pilot oxygen mask and a prototype of the revised mask design with 88 Korean Air Force pilots in terms of subjective discomfort, facial contact pressure,

  11. 77 FR 67433 - Community Advantage Pilot Program

    Science.gov (United States)

    2012-11-09

    ... comments. SUMMARY: The Community Advantage (``CA'') Pilot Program is a pilot program to increase SBA... small businesses and entrepreneurs in underserved markets, SBA is issuing this Notice to extend the term... Pilot Program was introduced to increase the number of SBA-guaranteed loans made to small businesses in...

  12. Cardiovascular Risk Factors in Airline Pilots.

    Science.gov (United States)

    Lord, Dana; Conlon, Helen Acree

    2018-02-01

    The health of an airline pilot is imperative to the safe travels of millions of people worldwide. Medical providers evaluate the cardiovascular risks for airline pilots and the medical requirements to obtain and maintain licensure as an airline pilot. It is the role of the occupational health nurse practitioner to evaluate and reduce the risk of cardiovascular disease in this population.

  13. A Neural Network Approach to Fluid Quantity Measurement in Dynamic Environments

    CERN Document Server

    Terzic, Edin; Nagarajah, Romesh; Alamgir, Muhammad

    2012-01-01

    Sloshing causes liquid to fluctuate, making accurate level readings difficult to obtain in dynamic environments. The measurement system described uses a single-tube capacitive sensor to obtain an instantaneous level reading of the fluid surface, thereby accurately determining the fluid quantity in the presence of slosh. A neural network based classification technique has been applied to predict the actual quantity of the fluid contained in a tank under sloshing conditions.   In A neural network approach to fluid quantity measurement in dynamic environments, effects of temperature variations and contamination on the capacitive sensor are discussed, and the authors propose that these effects can also be eliminated with the proposed neural network based classification system. To examine the performance of the classification system, many field trials were carried out on a running vehicle at various tank volume levels that range from 5 L to 50 L. The effectiveness of signal enhancement on the neural network base...

  14. Influence of quantities of brewer yeast on the performance of Anastrepha obliqua wild females (Diptera, Tephritidae

    Directory of Open Access Journals (Sweden)

    Cresoni-Pereira Carla

    2001-01-01

    Full Text Available Using artificial solid diets, experiments were performed with Anastrepha obliqua (Macquart, 1835 wild females in order to verify the influence of different quantities of brewer yeast on the performance and compensation behavior to unbalanced diets ingestion. The observed parameters were egg production, ingestion, diet efficiency and survival in the reproductive phase. Results indicated that there was no compensatory ingestion to different quantities of yeast and that the diet with 12.5g of yeast provided the best performance. The absence of compensatory ingestion is discussed based on the yeast phagostimulation and on the costs involved in solid diets ingestion. The relation between the analyzed parameters and the protein quantities in the diet were discussed.

  15. Influence of quantities of brewer yeast on the performance of Anastrepha obliqua wild females (Diptera, Tephritidae)

    International Nuclear Information System (INIS)

    Cresoni-Pereira, Carla; Zucoloto, Fernando Sergio

    2001-01-01

    Using artificial solid diets, experiments were performed with Anastrepha obliqua (Macquart, 1835) wild females in order to verify the influence of different quantities of brewer yeast on the performance and compensation behavior to unbalanced diets ingestion. The observed parameters were egg production, ingestion, diet efficiency and survival in the reproductive phase. Results indicated that there was no compensatory ingestion to different quantities of yeast and that the diet with 12.5g of yeast provided the best performance. The absence of compensatory ingestion is discussed based on the yeast phagostimulation and on the costs involved in solid diets ingestion. The relation between the analyzed parameters and the protein quantities in the diet were discussed. (author)

  16. Influence of quantities of brewer yeast on the performance of Anastrepha obliqua wild females (Diptera, Tephritidae)

    Energy Technology Data Exchange (ETDEWEB)

    Cresoni-Pereira, Carla; Zucoloto, Fernando Sergio [Universidade de Sao Paulo (USP), Ribeirao Preto, SP (Brazil). Faculdade de Filosofia, Ciencias e Letras. Dept. de Biologia

    2001-11-15

    Using artificial solid diets, experiments were performed with Anastrepha obliqua (Macquart, 1835) wild females in order to verify the influence of different quantities of brewer yeast on the performance and compensation behavior to unbalanced diets ingestion. The observed parameters were egg production, ingestion, diet efficiency and survival in the reproductive phase. Results indicated that there was no compensatory ingestion to different quantities of yeast and that the diet with 12.5g of yeast provided the best performance. The absence of compensatory ingestion is discussed based on the yeast phagostimulation and on the costs involved in solid diets ingestion. The relation between the analyzed parameters and the protein quantities in the diet were discussed. (author)

  17. Mechanical properties of cohesive soils in dependence on the water quantity and mineralogical composition

    Directory of Open Access Journals (Sweden)

    Ludvik Trauner

    2003-12-01

    Full Text Available This article explains the relationships between the water content, mineralogical properties and mechanical properties of saturated clays. The findings are based on theoretical analysis and were confirmed experimentally on monomineral clay samples. It was foundthat the quantity of intergrain water, which determines the undrained shear strength and compressibility of clays, consists of free pore water, and the firmly adsorbed water on the external surfaces of the clay grains. The free water quantity is the same for differentsaturated clays, at the same undrained shear strength, and same effective stress after consolidation and, likewise, the thickness of the water film around the clay grains. The total quantity of firmly adsorbed water depends on the specific surfaces of the clays. Theresult of this work is a new analytical formulation that gives the relationship between the water content and the mechanical properties of clays, taking into account their mineralogical characteristics.

  18. Arrangement for the measurement of the quantity of asphalt in an asphaltic compound

    International Nuclear Information System (INIS)

    Noma, I.; Taniguchi, K.

    1978-01-01

    The arrangement for the measurement of the quantity of asphalt in an asphaltic compound in an apparatus for the mixture of asphalt components and an aggregate for the formation of an asphaltic compound characterized by the inclusion of a member for the transmission of a neutron beam which reacts with the hydrogen atoms in the asphaltic compound in such a way that the energy of a neutron beam is adsorbed; a continuous transport device feeds a continuous supply of the asphalt compound past the neutron beam; a member responds to an automatic detector for the quantity of asphaltic components in the asphaltic compound and provides an adjustment so that the quantity [of asphaltic components in asphaltic compound] may be held at a constant value. (G.C.)

  19. Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

    Science.gov (United States)

    Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L

    2018-01-01

    This study examines whether energy drink use and binge drinking predict sleep quantity, sleep quality, and next-day tiredness among college students. Web-based daily data on substance use and sleep were collected across four semesters in 2009 and 2010 from 667 individuals for up to 56 days each, yielding information on 25,616 person-days. Controlling for average levels of energy drink use and binge drinking (i.e., 4+ drinks for women, 5+ drinks for men), on days when students consumed energy drinks, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not use energy drinks. Similarly, on days when students binge drank, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not binge drink. There was no significant interaction effect between binge drinking and energy drink use on the outcomes.

  20. Urgency of increasing the quantity and quality of student creativity program

    Science.gov (United States)

    Sarmini; Prasetya, Ketut; Nadiroh, Ulin

    2018-01-01

    Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

  1. Buyer-vendor coordination for fixed lifetime product with quantity discount under finite production rate

    Science.gov (United States)

    Zhang, Qinghong; Luo, Jianwen; Duan, Yongrui

    2016-03-01

    Buyer-vendor coordination has been widely addressed; however, the fixed lifetime of the product is seldom considered. In this paper, we study the coordination of an integrated production-inventory system with quantity discount for a fixed lifetime product under finite production rate and deterministic demand. We first derive the buyer's ordering policy and the vendor's production batch size in decentralised and centralised systems. We then compare the two systems and show the non-coordination of the ordering policies and the production batch sizes. To improve the supply chain efficiency, we propose quantity discount contract and prove that the contract can coordinate the buyer-vendor supply chain. Finally, we present analytically tractable solutions and give a numerical example to illustrate the benefits of the proposed quantity discount strategy.

  2. Among-species differences in pollen quality and quantity limitation: implications for endemics in biodiverse hotspots.

    Science.gov (United States)

    Alonso, Conchita; Navarro-Fernández, Carmen M; Arceo-Gómez, Gerardo; Meindl, George A; Parra-Tabla, Víctor; Ashman, Tia-Lynn

    2013-11-01

    Insufficient pollination is a function of quantity and quality of pollen receipt, and the relative contribution of each to pollen limitation may vary with intrinsic plant traits and extrinsic ecological properties. Community-level studies are essential to evaluate variation across species in quality limitation under common ecological conditions. This study examined whether endemic species are more limited by pollen quantity or quality than non-endemic co-flowering species in three endemic-rich plant communities located in biodiversity hotspots of different continents (Andalusia, California and Yucatan). Natural variations in pollen receipt and pollen tube formation were analysed for 20 insect-pollinated plants. Endemic and non-endemic species that co-flowered were paired in order to estimate and compare the quantity and quality components of pre-zygotic pollination success, obtained through piecewise regression analysis of the relationship between pollen grains and pollen tubes of naturally pollinated wilted flowers. Pollen tubes did not frequently exceed the number of ovules per flower. Only the combination of abundant and good quality pollen and a low number of ovules per flower conferred relief from pre-zygotic pollen limitation in the three stochastic pollination environments studied. Quality of pollen receipt was found to be as variable as quantity among study species. The relative pollination success of endemic and non-endemic species, and its quantity and quality components, was community dependent. Assessing both quality and quantity of pollen receipt is key to determining the ovule fertilization potential of both endemic and widespread plants in biodiverse hotspot regions. Large natural variation among flowers of the same species in the two components and pollen tube formation deserves further analysis in order to estimate the environmental, phenotypic and intraindividual sources of variation that may affect how plants evolve to overcome this limitation in

  3. Terms and definitions in the field of radiological technique. Dose quantities and units

    International Nuclear Information System (INIS)

    1985-12-01

    The standard gives the terms and definitions of concepts, dose quantities and units. The radiation field condition 'secondary electron equilibrium', which forms part of the definition of standard ion dose, is given more precisely. The term 'free in air' is used in its original meaning, i.e. characterization of measuring conditions excluding avoidable stray radiation, which deviates from DIN 6814, part 3/06.72. Dosemeters for measurement of standard ion dose of air kerma are calibrated 'free in air', but this calibration condition is not part of the quantity definition. The quantities standard ion dose or air kerma therefore can also be measured in any other material. The qunatitative relationships between standard ion dose and the quantities 'exposure' and air kerma, as given in the ICRU publication 33 'Quantities and Units' (1980), are explained. The standard introduces the SI units Gray (for energy dose), Sievert (for dose equivalent), and Becquerel (for the activity of a radioactive substance). As the change to the SI units conceals the approximated equality of the numerical values of the standrd ion dose of photon radiation in roentgen, of the energy dose for soft tissue in rad, and of the dose equivalent in rem, new definitions are given in accordance with ICRU 33 for the quantities specified dose rate, dose rate constant, and area exposure product. These definitions use the terms 'energy dose' and 'kerma'. The dose concepts applied in the field of radiation protection, especially ambient dose and individual dose, are defined as dose equivalents in compliance with the Radiation Protection Ordinance. The relevant sections present information on the conversion of standard ion dose values to the corresponding values of kerma, energy dose, or dose equivalent. (orig./HP) [de

  4. Uncertainties of exposure-related quantities in mammographic x-ray unit quality control

    International Nuclear Information System (INIS)

    Gregory, Kent J.; Pattison, John E.; Bibbo, Giovanni

    2006-01-01

    Breast screening programs operate in many countries with mammographic x-ray units subject to stringent quality control tests. These tests include the evaluation of quantities based on exposure measurements, such as half value layer, automatic exposure control reproducibility, average glandular dose, and radiation output rate. There are numerous error sources that contribute to the uncertainty of these exposure-related quantities, some of which are unique to the low energy x-ray spectrum produced by mammographic x-ray units. For each of these exposure-related quantities, the applicable error sources and their magnitudes vary, depending on the test equipment used to make the measurement, and whether or not relevant corrections have been applied. This study has identified and quantified a range of error sources that may be used to estimate the combined uncertainty of these exposure-related quantities, given the test equipment used and corrections applied. The uncertainty analysis uses methods described by the International Standards Organization's Guide to the Expression of Uncertainty in Measurement. Examples of how these error sources combine to give the uncertainty of the exposure-related quantities are presented. Using the best test equipment evaluated in this study, uncertainties of the four exposure-related quantities at the 95% confidence interval were found to be ±1.6% (half value layer), ±0.0008 (automatic exposure control reproducibility), ±2.3% (average glandular dose), and ±2.1% (radiation output rate). In some cases, using less precise test equipment or failing to apply corrections, resulted in uncertainties more than double in magnitude

  5. A modular method to handle multiple time-dependent quantities in Monte Carlo simulations

    International Nuclear Information System (INIS)

    Shin, J; Faddegon, B A; Perl, J; Schümann, J; Paganetti, H

    2012-01-01

    A general method for handling time-dependent quantities in Monte Carlo simulations was developed to make such simulations more accessible to the medical community for a wide range of applications in radiotherapy, including fluence and dose calculation. To describe time-dependent changes in the most general way, we developed a grammar of functions that we call ‘Time Features’. When a simulation quantity, such as the position of a geometrical object, an angle, a magnetic field, a current, etc, takes its value from a Time Feature, that quantity varies over time. The operation of time-dependent simulation was separated into distinct parts: the Sequence samples time values either sequentially at equal increments or randomly from a uniform distribution (allowing quantities to vary continuously in time), and then each time-dependent quantity is calculated according to its Time Feature. Due to this modular structure, time-dependent simulations, even in the presence of multiple time-dependent quantities, can be efficiently performed in a single simulation with any given time resolution. This approach has been implemented in TOPAS (TOol for PArticle Simulation), designed to make Monte Carlo simulations with Geant4 more accessible to both clinical and research physicists. To demonstrate the method, three clinical situations were simulated: a variable water column used to verify constancy of the Bragg peak of the Crocker Lab eye treatment facility of the University of California, the double-scattering treatment mode of the passive beam scattering system at Massachusetts General Hospital (MGH), where a spinning range modulator wheel accompanied by beam current modulation produces a spread-out Bragg peak, and the scanning mode at MGH, where time-dependent pulse shape, energy distribution and magnetic fields control Bragg peak positions. Results confirm the clinical applicability of the method. (paper)

  6. Operational quantities for use in external radiation protection measurements. An investigation of concepts and principles

    International Nuclear Information System (INIS)

    1983-01-01

    Under the terms of the Euratom Treaty the Commission of the European Communities is required to draw up basic standards for the health protection of the general public and workers against the dangers arising from ionizing radiation. The basic standards lay down reference values for particular quantities; these values are required to be measured, and appropriate steps taken to ensure that they are not exceeded. To ensure that the basic standards are applied uniformly in the Member States, it is necessary to harmonize not only national laws but also measurement and recording techniques. As a practical contribution towards this objective, the Commission has since 1964 been conducting intercomparison programmes on operational radiation protection dosimetry. Effective monitoring against the dangers of ionizing radiation cannot be guaranteed unless the measuring instruments meet the necessary requirements, the quantities measured are those for which limit values have been laid down, and the instruments can be calibrated unequivocally. The differences between the concepts of quantity and unit of measurement in radiation protection were often unclear. In the light of developments at international level, the introduction of the international system of units of measurements (SI units) and the contents of ICRP Publication No 26, the services of the European Community responsible for radiation protection decided to review the whole question of quantities. The introduction of the 'index' quantities (absorbed dose index and dose equivalent index) was greeted with initial enthusiasm, but it soon became clear, on closer critical examination, that these too had major shortcomings. The Commission, in collaboration with experts from the Member States of the European Community, has therefore set out in this publication the various considerations and points of view concerning the use of these quantities in practical dosimetry. It is hoped that this publication will be of use to all

  7. Improving the Quantity and Quality of Attendance Data to Enhance Student Retention

    Science.gov (United States)

    Bowen, Eleri; Price, Trevor; Lloyd, Steve; Thomas, Steve

    2005-01-01

    This article draws attention to local and global attendance monitoring in higher education. The paper outlines benefits of attendance monitoring for both the individual learner and university, and compares traditional paper-based attendance monitoring systems with an electronic system piloted in the Business School and School of Technology at the…

  8. DYNAMIC INVESTIGATION OF THE PURCHASE PRICE AND QUANTITY OF MAIZE AND PIG

    Directory of Open Access Journals (Sweden)

    Judit POÓR

    2007-11-01

    Full Text Available The aim of our examination was to show the cyclic character in the case of agricultural prices. Beside the investigation of prices the analysis of the purchased quantity is of importance too. We examined the way the prices and quantity exercise mutual influence and the connection between the maize purchase price and the pig purchase price. We compared the Hungarian purchase prices with some international ones, and analyzed the tendencies, the influence of open economies and the approach of the prices.

  9. A principle to correlate extreme values of excess thermodynamic functions with partial molar quantities

    Institute of Scientific and Technical Information of China (English)

    尉志武; 刘芸; 周蕊; 薛芳渝

    2001-01-01

    Excess thermodynamic properties are widely used quantitatively for fluids. It was found that at constant temperature and pressure a molar excess quantity of a mutually miscible binary mixture at the extreme points equals the excess partial molar quantities of the two components, i.e.F1E = F2E = FmE , forming a triple cross point. The relationship is hold for properties such as en-thalpy, entropy, Gibbs free energy, and volume, and is applicable for excess functions with multi extreme points. Solutions at extreme points can be referred to as special mixtures. Particularly fora special mixture of Gibbs free energy, activity coefficients of the two components are identical.

  10. A principle to correlate extreme values of excess thermody-namic functions with partial molar quantities

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Excess thermodynamic properties are widely used quantitatively for fluids. It was found that at constant temperature and pressure a molar excess quantity of a mutually miscible binary mixture at the extreme points equals the excess partial molar quantities of the two components, i.e. , forming a triple cross point. The relationship is hold for properties such as enthalpy, entropy, Gibbs free energy, and volume, and is applicable for excess functions with multi extreme points. Solutions at extreme points can be referred to as special mixtures. Particularly for a special mixture of Gibbs free energy, activity coefficients of the two components are identical.

  11. Prefrontal cortex and sensory cortices during working memory: quantity and quality.

    Science.gov (United States)

    Ku, Yixuan; Bodner, Mark; Zhou, Yong-Di

    2015-04-01

    The activity in sensory cortices and the prefrontal cortex (PFC) throughout the delay interval of working memory (WM) tasks reflect two aspects of WM-quality and quantity, respectively. The delay activity in sensory cortices is fine-tuned to sensory information and forms the neural basis of the precision of WM storage, while the delay activity in the PFC appears to represent behavioral goals and filters out irrelevant distractions, forming the neural basis of the quantity of task-relevant information in WM. The PFC and sensory cortices interact through different frequency bands of neuronal oscillation (theta, alpha, and gamma) to fulfill goal-directed behaviors.

  12. Is the Quantity Theory of Money Useful in Forecasting U.S. Inflation?

    DEFF Research Database (Denmark)

    Lanne, Markku; Luoto, Jani; Nyberg, Henri

    We propose a new simple model incorporating the implication of the quantity theory of money that money growth and ináation should move one for one in the long run, and, hence, ináation should be predictable by money growth. The model Öts postwar U.S. data well, and beats common univariate benchma...... models in forecasting ináation. Moreover, this evidence is quite robust, and predictability is found also in the Great moderation period. The detected predictability of ináation by money growth lends support to the quantity theory....

  13. Effect of gas quantity on two-phase flow characteristics of a mixed-flow pump

    OpenAIRE

    Qiang Fu; Fan Zhang; Rongsheng Zhu; Xiuli Wang

    2016-01-01

    The inlet gas quantity has a great influence on the performance and inner flow characteristics of a mixed-flow pump. In this article, both numerical and experimental methods are used to carry out this research work. The effects under the steady gas volume fraction state and the transient gas quantity variation process on the mixed-flow pump are investigated and compared in detail. It could be concluded that the head of the mixed-flow pump shows slight decline at the low gas volume fraction st...

  14. Characteristics Data Base: Programmer's guide to the LWR Quantities Data Base

    International Nuclear Information System (INIS)

    Jones, K.E.; Moore, R.S.

    1990-08-01

    The LWR Quantities Data Base is a menu-driven PC data base developed as part of OCRWM's waste, technical data base on the characteristics of potential repository wastes, which also includes non-LWR spent fuel, high-level and other materials. This programmer's guide completes the documentation for the LWR Quantities Data Base, the user's guide having been published previously. The PC data base itself may be requested from the Oak Ridge National Laboratory, using the order form provided in Volume 1 of publication DOE/RW-0184

  15. Conformal invariance and conserved quantities of Appell systems under second-class Mei symmetry

    International Nuclear Information System (INIS)

    Yi-Ping, Luo; Jing-Li, Fu

    2010-01-01

    In this paper we introduce the new concept of the conformal invariance and the conserved quantities for Appell systems under second-class Mei symmetry. The one-parameter infinitesimal transformation group and infinitesimal transformation vector of generator are described in detail. The conformal factor in the determining equations under second-class Mei symmetry is found. The relationship between Appell system's conformal invariance and Mei symmetry are discussed. And Appell system's conformal invariance under second-class Mei symmetry may lead to corresponding Hojman conserved quantities when the conformal invariance satisfies some conditions. Lastly, an example is provided to illustrate the application of the result. (general)

  16. Visualization of the Flux Rope Generation Process Using Large Quantities of MHD Simulation Data

    Directory of Open Access Journals (Sweden)

    Y Kubota

    2013-03-01

    Full Text Available We present a new concept of analysis using visualization of large quantities of simulation data. The time development of 3D objects with high temporal resolution provides the opportunity for scientific discovery. We visualize large quantities of simulation data using the visualization application 'Virtual Aurora' based on AVS (Advanced Visual Systems and the parallel distributed processing at "Space Weather Cloud" in NICT based on Gfarm technology. We introduce two results of high temporal resolution visualization: the magnetic flux rope generation process and dayside reconnection using a system of magnetic field line tracing.

  17. Organizational citizenship behavior and the quantity and quality of work group performance.

    Science.gov (United States)

    Podsakoff, P M; Ahearne, M; MacKenzie, S B

    1997-04-01

    Despite the widespread interest in the topic of organizational citizenship behaviors (OCBs), little empirical research has tested the fundamental assumption that these forms of behavior improve the effectiveness of work groups or organizations in which they are exhibited. In the present study, the effects of OCBs on the quantity and quality of the performance of 218 people working in 40 machine crews in a paper mill located in the Northeastern United States were examined. The results indicate that helping behavior and sportsmanship had significant effects on performance quantity and that helping behavior had a significant impact on performance quality. However, civic virtue had no effect on either performance measure.

  18. Photocatalytic Treatment of Shower Water Using a Pilot Scale Reactor

    Directory of Open Access Journals (Sweden)

    Yash Boyjoo

    2012-01-01

    Full Text Available Treatment of shower water deserves special consideration for reuse not only because of its low pollutant loading but also because it is produced in large quantities. In this study, a pilot scale study of photocatalytic degradation of impurities in real shower water was performed in a 31 L volume reactor using titanium dioxide as the photocatalyst. The reactor was operated in a continuous slurry recirculation mode. Several operational parameters were studied including the slurry initial pH, catalyst concentration, air flow rate, and slurry recirculation rate. Up to 57% of total organic carbon (TOC elimination was obtained after 6 hours of treatment (for 3.0 slurry initial pH, 0.07 gL−1 catalyst concentration, 1.8 Lmin−1 air flow rate, and 4.4 Lmin−1 slurry recirculation rate. This study showed that photocatalysis could be successfully transposed from bench scale to pilot scale. Furthermore, the ease of operation and the potential to use solar energy make photocatalysis an attractive prospect with respect to treatment of grey water.

  19. D22 Analysis of Pilot

    NARCIS (Netherlands)

    Boyle, Elizabeth; MacGregor, Sharon; Van Rosmalen, Peter; Manea, Madalina; Penanen, Tiina

    2015-01-01

    The evaluation of the CHERMUG games was carried out in 3 phases which contributed in different ways to the game development and evaluation. Different cohorts of staff and students were involved in each phase and a detailed account of the list of pilot institutions is shown in Deliverable 21. Phase 1

  20. Calculation of skin dose due to beta contamination using the new quantity of the ICRP 116: the local skin dose

    International Nuclear Information System (INIS)

    Bourgois, L.; Menard, S.; Comte, N.

    2017-01-01

    Values of the new protection quantity Local Skin Dose 'LSD', introduced by the International Commission on Radiological Protection (ICRP) Publication 116, were calculated for 134 β - or β + emitting radionuclides, using the Monte Carlo code MCNP6. Two types of source geometry are considered: a point source and disc-type surface contamination (the source is placed in contact with the skin). This new protection quantity is compared with the operational quantity H2 (0.07, 0 deg.), leading us to conclude that, in accordance with the rules of the ICRP, the operational quantity over-estimates the protection quantity to a reasonable extent, except in very rare cases for very low average beta energies. Thus, with the new skin model described in ICRP 116, there are no longer any major differences between the operational quantities and protection quantities estimated with the skin model described in ICRP 74. (authors)

  1. Pilot survey of patient dose from computed tomography in Bulgaria

    International Nuclear Information System (INIS)

    Vassileva, Jenia; Stoyanov, Desislav

    2008-01-01

    The number of computed tomography (CT) scanners in Bulgaria increased from 22 in 1996 to more than 160 in 2007. Big variety of scanners of different manufacturers and different generations exists in the country with predominant number of single-slice scanners. Significant part of the scanners is more than 10 years old. This work presents the pilot results from the measurements of CT dose quantities started in 2005 with the aim to spread them to a national survey of CT practice in the country. It was found that different clinical protocols are used for similar examination, resulting in large variations in dose quantities: CT air kerma index varied from 27.1 to 78.4 mGy for head examination, from 8.7 to 28.3 mGy for chest, 11.8 - 30.7 mGy for abdomen and 9.1 - 41.3 mGy for pelvis. The CT air kerma-length product for complete examination was found to vary from 310 to 1254 mGy.cm for head examination, from 215 to 893 mGy.cm for chest, from 265 to 615 mGy.cm for abdomen and from 220 to 761 mGy.cm for pelvis. The analysis demonstrated that the main reasons for found variations are differences in scanning geometry, beam quality, exposure parameters and scanning length. (author)

  2. Quantity and Variety of Fruit and Vegetable Consumption and Cancer Risk

    NARCIS (Netherlands)

    Jansen, M.C.J.F.; Bas Bueno de Mesquita, H.; Feskens, E.J.M.; Streppel, M.T.; Kok, F.J.; Kromhout, D.

    2004-01-01

    The recommendation for fruit and vegetable intake includes eating a certain quantity as well as a variety. The evidence for eating a variety is limited. We examined the association with cancer in a prospective cohort study among 730 Dutch men aged 65-84 yr followed for 10 years, resulting in 138

  3. The effect of the environment on the structure, quantity and composition of spruce needle wax

    International Nuclear Information System (INIS)

    Guenthardt-Goerg, M.S.

    1994-01-01

    The tubular structure (10-nonacosanol), as formed in spring on the wax surface of new spruce needles (Picea abies (L.)Karst.), or as regenerated on previous-year needles, becomes gradually fused and flattened in relation to needle exposure, particularly wind and rain. Structural flattening does not necessarily imply changes in wax quantity, composition or lead to changes in needle transpiration or photosynthesis, and was approximately reproduced by bathing excised twigs in water (with pH having little effect). In 4-year-old plants of one clone planted out at a Swiss plateau and alpine sites, changes in wax structure were similar to those found in mature trees. No such changes were found in plants with O 3 , SO 2 , ambient air, charcoal-filtered air, or in plants grown outside the chambers but shielded from rain. Area-related needle wax quantity in mature trees differed between the two sites, but did not differ in young plants under different treatments (fumigation or planted out at the sites). Minor differences in wax composition, however, were found to be related to the ozone dose of the fumigation or the ambient ozone dose at the sites. In each needle wax sample, 68 compounds grouped into 12 constituent classes were quantified. The quantity of the individual substituent classes varied among wax samples from genetically different mature trees at the two sites in a tree-specific way. Variation of these quantities was not larger than among young cloned plants after different treatments. (orig.)

  4. The Quality vs. the Quantity of Schooling: What Drives Economic Growth?

    Science.gov (United States)

    Breton, Theodore R.

    2011-01-01

    This paper challenges Hanushek and Woessmann's (2008) contention that the quality and not the quantity of schooling determines a nation's rate of economic growth. I first show that their statistical analysis is flawed. I then show that when a nation's average test scores and average schooling attainment are included in a national income model,…

  5. quantity and quality of litterfall in pure pine and pine/gmelina mixed ...

    African Journals Online (AJOL)

    KOME

    The quantity and nutrient composition of litterfall varies between tree species, ... quality in these plantations particularly in the south eastern part have not ... Research Institute of Nigeria (FRIN), Abia State, Nigeria that .... litter than deciduous vegetation (Vogt et al., 1986; Bray and .... Reiners, W. A. and Lang, G. E., 1987.

  6. ADM pseudotensors, conserved quantities and covariant conservation laws in general relativity

    International Nuclear Information System (INIS)

    Fatibene, L.; Ferraris, M.; Francaviglia, M.; Lusanna, L.

    2012-01-01

    The ADM formalism is reviewed and techniques for decomposing generic components of metric, connection and curvature are obtained. These techniques will turn out to be enough to decompose not only Einstein equations but also covariant conservation laws. Then a number of independent sets of hypotheses that are sufficient (though not necessary) to obtain standard ADM quantities (and Hamiltonian) from covariant conservation laws are considered. This determines explicitly the range in which standard techniques are equivalent to covariant conserved quantities. The Schwarzschild metric in different coordinates is then considered, showing how the standard ADM quantities fail dramatically in non-Cartesian coordinates or even worse when asymptotically flatness is not manifest; while, in view of their covariance, covariant conservation laws give the correct result in all cases. - Highlights: ► In the paper ADM conserved quantities for GR are obtained from augmented conservation laws. ► Boundary conditions for this to be possible are considered and compared with the literature. ► Some different forms of Schwarzschild solutions are considered as simple examples of different boundary conditions.

  7. Diet quantity influence phenotypic dimorphism during honey bee (Apis mellifera) caste determination

    Science.gov (United States)

    Queen and worker honey bees are genetically analogous, but morphologically and physiologically different. Nutritional differences in larval diets regulate caste determination. Our recent work indicates diet quantity has a strong influence on caste in honeybees, and that queen induction can occur in ...

  8. An Adaptive Information Quantity-Based Broadcast Protocol for Safety Services in VANET

    Directory of Open Access Journals (Sweden)

    Wenjie Wang

    2016-01-01

    Full Text Available Vehicle-to-vehicle communication plays a significantly important role in implementing safe and efficient road traffic. When disseminating safety messages in the network, the information quantity on safety packets changes over time and space. However, most of existing protocols view each packet the same to disseminate, preventing vehicles from collecting more recent and precise safety information. Hence, an information quantity-based broadcast protocol is proposed in this paper to ensure the efficiency of safety messages dissemination. In particular, we propose the concept of emergency-degree to evaluate packets’ information quantity. Then we present EDCast, an emergency-degree-based broadcast protocol. EDCast differentiates each packet’s priority for accessing the channel based on its emergency-degree so as to provide vehicles with more safety information timely and accurately. In addition, an adaptive scheme is presented to ensure fast dissemination of messages in different network condition. We compare the performance of EDCast with those of three other representative protocols in a typical highway scenario. Simulation results indicate that EDCast achieves higher broadcast efficiency and less redundancy with less delivery delay. What we found demonstrates that it is feasible and necessary for incorporating information quantity of messages in designing an efficient safety message broadcast protocol.

  9. Comparative Assessment of Physical and Social Determinants of Water Quantity and Water Quality Concerns

    Science.gov (United States)

    Gunda, T.; Hornberger, G. M.

    2017-12-01

    Concerns over water resources have evolved over time, from physical availability to economic access and recently, to a more comprehensive study of "water security," which is inherently interdisciplinary because a secure water system is influenced by and affects both physical and social components. The concept of water security carries connotations of both an adequate supply of water as well as water that meets certain quality standards. Although the term "water security" has many interpretations in the literature, the research field has not yet developed a synthetic analysis of water security as both a quantity (availability) and quality (contamination) issue. Using qualitative comparative and multi-regression analyses, we evaluate the primary physical and social factors influencing U.S. states' water security from a quantity perspective and from a quality perspective. Water system characteristics are collated from academic and government sources and include access/use, governance, and sociodemographic, and ecosystem metrics. Our analysis indicates differences in variables driving availability and contamination concerns; for example, climate is a more significant determinant in water quantity-based security analyses than in water quality-based security analyses. We will also discuss coevolution of system traits and the merits of constructing a robust water security index based on the relative importance of metrics from our analyses. These insights will improve understanding of the complex interactions between quantity and quality aspects and thus, overall security of water systems.

  10. 21 CFR 161.30 - Declaration of quantity of contents on labels for canned oysters.

    Science.gov (United States)

    2010-04-01

    ... canned oysters. 161.30 Section 161.30 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH....30 Declaration of quantity of contents on labels for canned oysters. (a) For many years packers of canned oysters in the Gulf area of the United States have labeled their output with a declaration of the...

  11. Factors Affecting the Pre-Contract use of the Bill of Quantities | Ogbu ...

    African Journals Online (AJOL)

    Data were collected through the administration of questionnaire on 53 randomly selected construction consultants. Majority of the respondents (47.2%) were quantity surveyors, 20.8% were builders, 17% were architects, 9.4% were civil engineers and 5.7% were mechanical and electrical engineers. The data collected were ...

  12. Statistical Analysis of the Impact of Wind Power on Market Quantities and Power Flows

    DEFF Research Database (Denmark)

    Pinson, Pierre; Jónsson, Tryggvi; Zugno, Marco

    2012-01-01

    In view of the increasing penetration of wind power in a number of power systems and markets worldwide, we discuss some of the impacts that wind energy may have on market quantities and cross-border power flows. These impacts are uncovered through statistical analyses of actual market and flow data...... of load and wind power forecasts on Danish and German electricity markets....

  13. Comparing children's Homo sapiens and chimpanzees' Pan troglodytes quantity judgments of sequentially presented sets of items

    Directory of Open Access Journals (Sweden)

    Michael J. BERAN, Julie S. JOHNSON-PYNN, Christopher READY

    2011-08-01

    Full Text Available We presented a quantity judgment task that involved comparing two sequentially presented sets of items to preschoolers and chimpanzees using nearly identical procedures that excluded verbal instructions to children. Trial difficulty in this task reflected the ratio difference between sets of discrete items where larger ratios (e.g., 0.80 as from comparing 4 to 5 were more difficult than smaller ones (e.g., 0.50 as from comparing 4 to 8. Children also completed verbal-based tasks probing the relationship between counting proficiency and performance on the quantity judgment task of sequentially presented identical sized items. Both species’ performance was best when ratios between comparison sets were small regardless of set size in all types of tasks. Generally, chimpanzees and older children performed better than younger children except at larger ratios. Children’s counting proficiency was not related to success in choosing the larger of two quantities of identical-sized items. These results indicate that chimpanzees and children share an approximate number sense that is reflected through analog magnitude estimation when comparing quantities [Current Zoology 57 (4: 419–428, 2011].

  14. 21 CFR 201.51 - Declaration of net quantity of contents.

    Science.gov (United States)

    2010-04-01

    ... augmented to give the weight or measure of the drug units or the quantity of each active ingredient in each... an active ingredient in a unit of a drug. (d) The declaration shall appear as a distinct item on the.... In the case of a liquid drug in ampules or vials, intended for injection, the declaration shall be...

  15. Effects of dietary protein quality and quantity on albino rat tissue ...

    African Journals Online (AJOL)

    Effects of dietary protein quality and quantity on albino rat tissue serum protein, erythrocyte fragility and bone mineral content. ... The 20% protein diet was a commercial diet better in nutrient composition and quality than the diet containing 17 and 15% protein formulated in our laboratory. At the end of 21 days, kidney, testes, ...

  16. Quantity versus Quality: A New Approach to Examine the Relationship between Technology Use and Student Outcomes

    Science.gov (United States)

    Lei, Jing

    2010-01-01

    The author argues that to examine the relationship between technology use and student outcomes, the quality of technology use--how, and what, technology is used--is a more significant factor than the quantity of technology use--how much technology is used. This argument was exemplified by an empirical study that used both angles to examine the…

  17. Influences of management of Southern forests on water quantity and quality

    Science.gov (United States)

    Ge Sun; Mark Riedel; Rhett Jackson; Randy Kolka; Devendra Amatya; Jim Shepard

    2004-01-01

    Water is a key output of southern forests and is critical to other processes, functions, and values of forest ecosystems. This chapter synthesizes published literature about the effects of forest management practices on water quantity and water quality across the Southern United States region. We evaluate the influences of forest management at different temporal and...

  18. The impact of symbolic and non-symbolic quantity on spatial learning.

    Directory of Open Access Journals (Sweden)

    Koleen McCrink

    Full Text Available An implicit mapping of number to space via a "mental number line" occurs automatically in adulthood. Here, we systematically explore the influence of differing representations of quantity (no quantity, non-symbolic magnitudes, and symbolic numbers and directional flow of stimuli (random flow, left-to-right, or right-to-left on learning and attention via a match-to-sample working memory task. When recalling a cognitively demanding string of spatial locations, subjects performed best when information was presented right-to-left. When non-symbolic or symbolic numerical arrays were embedded in these spatial locations, and mental number line congruency prompted, this effect was attenuated and in some cases reversed. In particular, low-performing female participants who viewed increasing non-symbolic number arrays paired with the spatial locations exhibited better recall for left-to-right directional flow information relative to right-to-left, and better processing for the left side of space relative to the right side of space. The presence of symbolic number during spatial learning enhanced recall to a greater degree than non-symbolic number--especially for female participants, and especially when cognitive load is high--and this difference was independent of directional flow of information. We conclude that quantity representations have the potential to scaffold spatial memory, but this potential is subtle, and mediated by the nature of the quantity and the gender and performance level of the learner.

  19. 48 CFR 1552.217-74 - Option for increased quantity-cost-plus-award-fee contract.

    Science.gov (United States)

    2010-10-01

    ... quantity-cost-plus-award-fee contract. 1552.217-74 Section 1552.217-74 Federal Acquisition Regulations... Texts of Provisions and Clauses 1552.217-74 Option for increased quantity—cost-plus-award-fee contract. As prescribed in 1517.208(e), insert this contract clause in cost-plus-award-fee term contracts when...

  20. Why should quantities and units be practical (Hans Christian Andersen please forgive me)

    International Nuclear Information System (INIS)

    Poston, J.W.

    1976-01-01

    The author considers the fairy tale quality of the thinking behind the introduction of new radiation protection units proposed by ICRU 73. It is felt that the new quantities and their special units add nothing to the health physics profession. The uncertainties with the linear vs threshold hypotheses remain unresolved by these actions. (U.K.)