Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

Energy Technology Data Exchange (ETDEWEB)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-11-15

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

International Nuclear Information System (INIS)

Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.; Stow, S.H.

2003-01-01

The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of a ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.

Mg-spinel lithology: A new rock type on the lunar farside

Science.gov (United States)

Pieters, C.M.; Besse, S.; Boardman, J.; Buratti, B.; Cheek, L.; Clark, R.N.; Combe, J.-P.; Dhingra, D.; Goswami, J.N.; Green, R.O.; Head, J.W.; Isaacson, P.; Klima, R.; Kramer, G.; Lundeen, S.; Malaret, E.; McCord, T.; Mustard, J.; Nettles, J.; Petro, N.; Runyon, C.; Staid, M.; Sunshine, J.; Taylor, L.A.; Thaisen, K.; Tompkins, S.; Whitten, J.

2011-01-01

High-resolution compositional data from Moon Mineralogy Mapper (M 3) for the Moscoviense region on the lunar farside reveal three unusual, but distinctive, rock types along the inner basin ring. These are designated "OOS" since they are dominated by high concentrations of orthopyroxene, olivine, and Mg-rich spinel, respectively. The OOS occur as small areas, each a few kilometers in size, that are widely separated within the highly feldspathic setting of the basin rim. Although the abundance of plagioclase is not well constrained within the OOS, the mafic mineral content is exceptionally high, and two of the rock types could approach pyroxenite and harzburgite in composition. The third is a new rock type identified on the Moon that is dominated by Mg-rich spinel with no other mafic minerals detectable (lunar crust; they may thus be near contemporaneous with crustal products from the cooling magma ocean. Copyright ?? 2011 by the American Geophysical Union.

APXS of First Rocks Encountered by Curiosity in Gale Crater: Geochemical Diversity and Volatile Element (K and ZN) Enrichment

Science.gov (United States)

Schmidt, M. E.; King, P. L.; Gellert, R.; Elliott, B.; Thompson, L.; Berger, J.; Bridges, J.; Campbell, J. L; Grotzinger, J.; Hurowitz, J.;

Ecohydrological Responses to Diversion of Groundwater: Case Study of a Deep-Rock Repository for Spent Nuclear Fuel in Sweden

International Nuclear Information System (INIS)

Werner, Kent; Collinder, Per; Berglund, Sten; Maartensson, Erik

2013-01-01

Planning and license applications concerning groundwater diversion in areas containing water-dependent or water-favored habitats must take into account both hydrological effects and associated ecological consequences. There is at present no established methodology to assess such ecohydrological responses. Thus, this paper describes a new stepwise methodology to assess ecohydrological responses to groundwater diversion from, e.g., water-drained pits, shafts, tunnels, and caverns in rock below the groundwater table. The methodology is illustrated using the planned deep-rock repository for spent nuclear fuel at Forsmark in central Sweden as a case study, offering access to a unique hydrological and ecological dataset. The case study demonstrates that results of ecohydrological assessments can provide useful inputs to planning of monitoring programs and mitigation measures in infrastructure projects. As a result of the assessment, artificial water supply to wetlands is planned in order to preserve biological diversity, nature values, and vulnerable species

Pattern Recognition of Signals for the Fault-Slip Type of Rock Burst in Coal Mines

Directory of Open Access Journals (Sweden)

X. S. Liu

2015-01-01

Full Text Available The fault-slip type of rock burst is a major threat to the safety of coal mining, and effectively recognizing its signals patterns is the foundation for the early warning and prevention. At first, a mechanical model of the fault-slip was established and the mechanism of the rock burst induced by the fault-slip was revealed. Then, the patterns of the electromagnetic radiation, acoustic emission (AE, and microseismic signals in the fault-slip type of rock burst were proposed, in that before the rock burst occurs, the electromagnetic radiation intensity near the sliding surface increases rapidly, the AE energy rises exponentially, and the energy released by microseismic events experiences at least one peak and is close to the next peak. At last, in situ investigations were performed at number 1412 coal face in the Huafeng Mine, China. Results showed that the signals patterns proposed are in good agreement with the process of the fault-slip type of rock burst. The pattern recognition can provide a basis for the early warning and the implementation of relief measures of the fault-slip type of rock burst.

Testing the effect of the rock record on diversity: a multidisciplinary approach to elucidating the generic richness of sauropodomorph dinosaurs through time.

Science.gov (United States)

Mannion, Philip D; Upchurch, Paul; Carrano, Matthew T; Barrett, Paul M

2011-02-01

The accurate reconstruction of palaeobiodiversity patterns is central to a detailed understanding of the macroevolutionary history of a group of organisms. However, there is increasing evidence that diversity patterns observed directly from the fossil record are strongly influenced by fluctuations in the quality of our sampling of the rock record; thus, any patterns we see may reflect sampling biases, rather than genuine biological signals. Previous dinosaur diversity studies have suggested that fluctuations in sauropodomorph palaeobiodiversity reflect genuine biological signals, in comparison to theropods and ornithischians whose diversity seems to be largely controlled by the rock record. Most previous diversity analyses that have attempted to take into account the effects of sampling biases have used only a single method or proxy: here we use a number of techniques in order to elucidate diversity. A global database of all known sauropodomorph body fossil occurrences (2024) was constructed. A taxic diversity curve for all valid sauropodomorph genera was extracted from this database and compared statistically with several sampling proxies (rock outcrop area and dinosaur-bearing formations and collections), each of which captures a different aspect of fossil record sampling. Phylogenetic diversity estimates, residuals and sample-based rarefaction (including the first attempt to capture 'cryptic' diversity in dinosaurs) were implemented to investigate further the effects of sampling. After 'removal' of biases, sauropodomorph diversity appears to be genuinely high in the Norian, Pliensbachian-Toarcian, Bathonian-Callovian and Kimmeridgian-Tithonian (with a small peak in the Aptian), whereas low diversity levels are recorded for the Oxfordian and Berriasian-Barremian, with the Jurassic/Cretaceous boundary seemingly representing a real diversity trough. Observed diversity in the remaining Triassic-Jurassic stages appears to be largely driven by sampling effort. Late

Characterization and differentiation of rock varnish types from different environments by microanalytical techniques

Energy Technology Data Exchange (ETDEWEB)

Macholdt, D. S. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Jochum, K. P. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Pöhlker, C. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Arangio, A. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Förster, J. -D. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Stoll, B. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Weis, U. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Weber, B. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Müller, M. [Max Planck Inst. for Polymer Research, Mainz (Germany); Kappl, M. [Max Planck Inst. for Polymer Research, Mainz (Germany); Shiraiwa, M. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Kilcoyne, A. L. D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Weigand, M. [Max Planck Inst. for Intelligent Systems, Stuttgart (Germany); Scholz, D. [Johannes Gutenberg Univ., Mainz (Germany); Haug, G. H. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; Al-Amri, A. [King Saud Univ., Riyadh (Saudi Arabia); Andreae, M. O. [Max Planck Society, Mainz (Germany). Max Planck Inst. for Chemistry; King Saud Univ., Riyadh (Saudi Arabia)

2017-04-13

We investigated rock varnishes collected from several locations and environments worldwide by a wide range of microanalytical techniques. These techniques were selected to address the challenges posed by the chemical and structural complexity within the micrometer- to nanometer-sized structures in these geological materials. Femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs LA-ICP-MS), scanning transmission X-ray microscopy-near edge X-ray adsorption fine structure spectroscopy (STXM-NEXAFS) in combination with scanning electron microscopy (SEM) of focused ion beam (FIB) ultra-thin (100–200 nm) sections, conventional and polarization microscopy, as well as electron paramagnetic resonance (EPR) measurements were used to obtain information about these rock varnishes. Rock varnishes from different environments, which cannot readily be distinguished based on their macroscopic appearance, differ significantly in their constituent elemental mass fractions, e.g., of Mn, Fe, Ni, Co, Ba, and Pb, and their rare earth element (REE) patterns. Structural characteristics such as the particle sizes of embedded dust grains, internal structures such as layers of Mn-, Fe-, and Ca -rich material, and structures such as cavities varied between varnishes from different environments and regions in the world. The EPR spectra were consistent with aged biogenic Mn oxides in all samples, but showed subtle differences between samples of different origin. Our observations allow us to separate rock varnishes into different types, with differences that might be indicators of distinct geneses. Five different types of rock varnish could be distinguished, Type I–V, of which only Type I might be used as potential paleoclimate archive. Each varnish type has specific characteristics in terms of their elemental composition, element distribution, and structures. The combination of element ratios (Mn/Ba, Al/Ni, Mn/REY, Mn/Ce, Mn/Pb, La N /Yb N , and Ce/Ce*), total REE

A Modeling Study of Flow Diversion and Focusing in unsaturated Fractured Rocks

International Nuclear Information System (INIS)

Pan, Lehua; Wu, Yu-Shu; Zhang, Keni

2002-01-01

This study presents a systematic approach to analyze the flow diversion and flow focusing caused by the natural flow-barrier system in the unsaturated zone (UZ) of Yucca Mountain, Nevada, under ambient steady-state flow conditions. An existing analytical solution for analyzing capillary barrier in porous media has been extended to apply to the fractured porous rock. The new analytical solutions are used to identify the critical layers and to provide the guidance for generation of a proper three-dimensional (3-D), site-scale numerical grid. A large-scale 3-D numerical model (with more than a million grid blocks) has been developed with site-specific data to analyze the major flow patterns in the mountain. Our analyses show that large-scale lateral flow could take place in the UZ under ambient conditions, as a result of capillary barriers formed at the contacts of heterogeneous rock layers. This lateral flow runs generally toward the east (in the southern part) or southeast (in the northern part), which is consistent with the dip of the layer contacts. About 90 percent of the total lateral flow is found to be conducted by only a few critical rock layers. Faults that penetrate these rock layers act as vertical capillary barriers that stop the lateral flow. The combined effect of horizontal and vertical capillary barriers resulted in reduced percolation flow through repository horizon in general but focused downward flow along those penetrating faults. The model results were found to be consistent with the field water saturation. The findings of this study are consistent with a previously published two-dimensional (2-D) analysis and recent published modeling results using field-observed Cl-data

An evaluation of thematic mapper simulator data for the geobotanical discrimination of rock types in Southwest Oregon

Science.gov (United States)

Weinstock, K. J.; Morrissey, L. A.

1984-01-01

Rock type identification may be assisted by the use of remote sensing of associated vegetation, particularly in areas of dense vegetative cover where surface materials are not imaged directly by the sensor. The geobotanical discrimination of ultramafic parent materials was investigated and analytical techniques for lithologic mapping and mineral exploration were developed. The utility of remotely sensed data to discriminate vegetation types associated with ultramafic parent materials in a study area in southwest Oregon were evaluated. A number of specific objectives were identified, which include: (1) establishment of the association between vegetation and rock types; (2) examination of the spectral separability of vegetation types associated with rock types; (3) determination of the contribution of each TMS band for discriminating vegetation associated with rock types and (4) comparison of analytical techniques for spectrally classifying vegetation.

Distribution regularities and prospecting of carbonate-siliceous-argillitic rock type uranium deposit in China

International Nuclear Information System (INIS)

Zhao Fengmin; Pan Yan

2012-01-01

The carbonate-siliceous-argillitic rock type uranium deposit is one of the important types of uranium deposits in China. Exogenic permeability type and hydrothermal type are dominated in genetic type. Four mineralization zones, two independent mineralization districts, two potential mineralization zones can be classified in China, uranium mineralization districts can be classified further. They are classified as four levels through the potential metallogenic evaluation on the mineralization districts, an important prospective area in the near future. In order to develop and make use of carbonate-siliceous-argillitic rock type uranium resources, exploration and study should be listed in the development planning on uranium geology. (authors)

Epilithic Cyanobacterial Communities of a Marine Tropical Beach Rock (Heron Island, Great Barrier Reef): Diversity and Diazotrophy▿

Science.gov (United States)

Díez, Beatriz; Bauer, Karolina; Bergman, Birgitta

2007-01-01

The diversity and nitrogenase activity of epilithic marine microbes in a Holocene beach rock (Heron Island, Great Barrier Reef, Australia) with a proposed biological calcification “microbialite” origin were examined. Partial 16S rRNA gene sequences from the dominant mat (a coherent and layered pink-pigmented community spread over the beach rock) and biofilms (nonstratified, differently pigmented microbial communities of small shallow depressions) were retrieved using denaturing gradient gel electrophoresis (DGGE), and a clone library was retrieved from the dominant mat. The 16S rRNA gene sequences and morphological analyses revealed heterogeneity in the cyanobacterial distribution patterns. The nonheterocystous filamentous genus Blennothrix sp., phylogenetically related to Lyngbya, dominated the mat together with unidentified nonheterocystous filaments of members of the Pseudanabaenaceae and the unicellular genus Chroococcidiopsis. The dominance and three-dimensional intertwined distribution of these organisms were confirmed by nonintrusive scanning microscopy. In contrast, the less pronounced biofilms were dominated by the heterocystous cyanobacterial genus Calothrix, two unicellular Entophysalis morphotypes, Lyngbya spp., and members of the Pseudanabaenaceae family. Cytophaga-Flavobacterium-Bacteroides and Alphaproteobacteria phylotypes were also retrieved from the beach rock. The microbial diversity of the dominant mat was accompanied by high nocturnal nitrogenase activities (as determined by in situ acetylene reduction assays). A new DGGE nifH gene optimization approach for cyanobacterial nitrogen fixers showed that the sequences retrieved from the dominant mat were related to nonheterocystous uncultured cyanobacterial phylotypes, only distantly related to sequences of nitrogen-fixing cultured cyanobacteria. These data stress the occurrence and importance of nonheterocystous epilithic cyanobacteria, and it is hypothesized that such epilithic cyanobacteria

Genetic diversity and structure in the Endangered Allen Cays Rock Iguana, Cyclura cychlura inornata

Science.gov (United States)

Aplasca, Andrea C.; Iverson, John B.; Welch, Mark E.; Colosimo, Giuliano

2016-01-01

The Endangered Allen Cays Rock Iguana (Cyclura cychlura inornata) is endemic to the Allen Cays, a tiny cluster of islands in the Bahamas. Naturally occurring populations exist on only two cays (<4 ha each). However, populations of unknown origin were recently discovered on four additional cays. To investigate patterns of genetic variation among these populations, we analyzed nuclear and mitochondrial markers for 268 individuals. Analysis of three mitochondrial gene regions (2,328 bp) and data for eight nuclear microsatellite loci indicated low genetic diversity overall. Estimates of effective population sizes based on multilocus genotypes were also extremely low. Despite low diversity, significant population structuring and variation in genetic diversity measures were detected among cays. Genetic data confirm the source population for an experimentally translocated population while raising concerns regarding other, unauthorized, translocations. Reduced heterozygosity is consistent with a documented historical population decline due to overharvest. This study provides the first range-wide genetic analysis of this subspecies. We suggest strategies to maximize genetic diversity during ongoing recovery including additional translocations to establish assurance populations and additional protective measures for the two remaining natural populations. PMID:26989628

Genetic diversity and structure in the Endangered Allen Cays Rock Iguana, Cyclura cychlura inornata

Directory of Open Access Journals (Sweden)

Andrea C. Aplasca

2016-03-01

Full Text Available The Endangered Allen Cays Rock Iguana (Cyclura cychlura inornata is endemic to the Allen Cays, a tiny cluster of islands in the Bahamas. Naturally occurring populations exist on only two cays (<4 ha each. However, populations of unknown origin were recently discovered on four additional cays. To investigate patterns of genetic variation among these populations, we analyzed nuclear and mitochondrial markers for 268 individuals. Analysis of three mitochondrial gene regions (2,328 bp and data for eight nuclear microsatellite loci indicated low genetic diversity overall. Estimates of effective population sizes based on multilocus genotypes were also extremely low. Despite low diversity, significant population structuring and variation in genetic diversity measures were detected among cays. Genetic data confirm the source population for an experimentally translocated population while raising concerns regarding other, unauthorized, translocations. Reduced heterozygosity is consistent with a documented historical population decline due to overharvest. This study provides the first range-wide genetic analysis of this subspecies. We suggest strategies to maximize genetic diversity during ongoing recovery including additional translocations to establish assurance populations and additional protective measures for the two remaining natural populations.

Joint simulation of stationary grade and non-stationary rock type for quantifying geological uncertainty in a copper deposit

Science.gov (United States)

Maleki, Mohammad; Emery, Xavier

2017-12-01

In mineral resources evaluation, the joint simulation of a quantitative variable, such as a metal grade, and a categorical variable, such as a rock type, is challenging when one wants to reproduce spatial trends of the rock type domains, a feature that makes a stationarity assumption questionable. To address this problem, this work presents methodological and practical proposals for jointly simulating a grade and a rock type, when the former is represented by the transform of a stationary Gaussian random field and the latter is obtained by truncating an intrinsic random field of order k with Gaussian generalized increments. The proposals concern both the inference of the model parameters and the construction of realizations conditioned to existing data. The main difficulty is the identification of the spatial correlation structure, for which a semi-automated algorithm is designed, based on a least squares fitting of the data-to-data indicator covariances and grade-indicator cross-covariances. The proposed models and algorithms are applied to jointly simulate the copper grade and the rock type in a Chilean porphyry copper deposit. The results show their ability to reproduce the gradual transitions of the grade when crossing a rock type boundary, as well as the spatial zonation of the rock type.

Diverse P-T paths for the Cycladic ultramafic rock associations: Constraints on their origin, emplacement and exhumation

International Nuclear Information System (INIS)

Katzir, Y; Garfunkel, Z; Avigad, D; Matthews, A

2008-01-01

Within the Alpine orogen of the Cyclades ultramafic rocks occur in diverse tectonic positions, are associated with a variety of rock sequences and are regionally metamorphosed at variable conditions. Here this diversity is interpreted in terms of variable mechanisms for incorporation of mantle rocks into orogenic belts and used to better constrain spatial heterogeneity of P-T burial and exhumation paths in the Cyclades. The Cycladic Blueschist Unit (CBU) was metamorphosed first at high pressure conditions in the Eocene (M1) and variably overprinted during exhumation in the Early Miocene (M2). On the islands of Syros and Evia the CBU includes relatively thin HP-LT ophiolitic melange intervals hosted by meta-sedimentary sequences. Meta-serpentinites are associated with eclogitized metagabbro and metabasites on Syros, but with epidote blueschists on Evia. Given the wide and comparable geochemical heterogeneity in the Syros and Evian melanges, the Syros metabasites record higher M1 temperatures (450-500 deg. C) relative to their Evian counterparts (400-430 deg. C). The M2 overprint is manifested in Syros by greenschist facies assemblages (∼450 deg. C), whereas pumpellyite-actinolite assemblage (∼350 deg. C) overgrew blueschists in Evia. Within the M2 migmatized leucogneiss core of the Naxos dome (∼700 0 C) meta-peridotite lenses are the sole preservers of pre-M2 history. The Naxos meta-peridotites possess relict mantle assemblage, fertile spinel lherzolite chemical composition and mantle-like oxygen isotope ratios. Thus unlike ophiolite-associated ultramafics in the Cyclades that were serpentinized prior to metamorphism, the Naxos metaperidotites were directly emplaced from the subcontinental mantle into an underthrust continent during collision and HP metamorphism. Ultramafic assemblages constrain M1 temperatures on Naxos to 550-650 0 C. It follows that going southeastwards from Evia through Syros to Naxos progressively deeper levels of the subducted plate are

Apollo rocks, fines and soil cores

Science.gov (United States)

Allton, J.; Bevill, T.

Apollo rocks and soils not only established basic lunar properties and ground truth for global remote sensing, they also provided important lessons for planetary protection (Adv. Space Res ., 1998, v. 22, no. 3 pp. 373-382). The six Apollo missions returned 2196 samples weighing 381.7 kg, comprised of rocks, fines, soil cores and 2 gas samples. By examining which samples were allocated for scientific investigations, information was obtained on usefulness of sampling strategy, sampling devices and containers, sample types and diversity, and on size of sample needed by various disciplines. Diversity was increased by using rakes to gather small rocks on the Moon and by removing fragments >1 mm from soils by sieving in the laboratory. Breccias and soil cores are diverse internally. Per unit weight these samples were more often allocated for research. Apollo investigators became adept at wringing information from very small sample sizes. By pushing the analytical limits, the main concern was adequate size for representative sampling. Typical allocations for trace element analyses were 750 mg for rocks, 300 mg for fines and 70 mg for core subsamples. Age-dating and isotope systematics allocations were typically 1 g for rocks and fines, but only 10% of that amount for core depth subsamples. Historically, allocations for organics and microbiology were 4 g (10% for cores). Modern allocations for biomarker detection are 100mg. Other disciplines supported have been cosmogenic nuclides, rock and soil petrology, sedimentary volatiles, reflectance, magnetics, and biohazard studies . Highly applicable to future sample return missions was the Apollo experience with organic contamination, estimated to be from 1 to 5 ng/g sample for Apollo 11 (Simonheit &Flory, 1970; Apollo 11, 12 &13 Organic contamination Monitoring History, U.C. Berkeley; Burlingame et al., 1970, Apollo 11 LSC , pp. 1779-1792). Eleven sources of contaminants, of which 7 are applicable to robotic missions, were

Rock Tea extract (Jasonia glutinosa) relaxes rat aortic smooth muscle by inhibition of L-type Ca(2+) channels.

Science.gov (United States)

Valero, Marta Sofía; Oliván-Viguera, Aida; Garrido, Irene; Langa, Elisa; Berzosa, César; López, Víctor; Gómez-Rincón, Carlota; Murillo, María Divina; Köhler, Ralf

2015-12-01

In traditional herbal medicine, Rock Tea (Jasonia glutinosa) is known for its prophylactic and therapeutic value in various disorders including arterial hypertension. However, the mechanism by which Rock Tea exerts blood pressure-lowering actions has not been elucidated yet. Our aim was to demonstrate vasorelaxing effects of Rock Tea extract and to reveal its possible action mechanism. Isometric myography was conducted on high-K+-precontracted rings from rat thoracic aorta and tested extracts at concentrations of 0.5-5 mg/ml. Whole-cell patch-clamp experiments were performed in rat aortic vascular smooth muscle cells (line A7r5) to determine blocking effects on L-type Ca(2+) channels. Rock Tea extract relaxed the aorta contracted by high [K+] concentration dependently with an EC50 of ≈2.4 mg/ml and produced ≈75 % relaxation at the highest concentration tested. The L-type Ca(2+) channel blocker, verapamil (10(-6) M), had similar effects. Rock Tea extract had no effect in nominally Ca(2+)-free high-K(+) buffer but significantly inhibited contractions to re-addition of Ca(2+). Rock Tea extract inhibited the contractions induced by the L-type Ca(2+) channel activator Bay K 8644 (10(-5) M) and by phenylephrine (10(-6) M). Rock Tea extract and Y-27632 (10(-6) M), Rho-kinase inhibitor, had similar effects and the respective effects were not additive. Patch-clamp experiments demonstrated that Rock Tea extract (2.5 mg/ml) virtually abolished L-type Ca(2+) currents in A7r5. We conclude that Rock Tea extract produced vasorelaxation of rat aorta and that this relaxant effect is mediated by inhibition of L-type Ca(2+) channels. Rock Tea extracts may be of phytomedicinal value for prevention and adjuvant treatment of hypertension and other cardiovascular diseases.

3D pore-type digital rock modeling of natural gas hydrate for permafrost and numerical simulation of electrical properties

Science.gov (United States)

Dong, Huaimin; Sun, Jianmeng; Lin, Zhenzhou; Fang, Hui; Li, Yafen; Cui, Likai; Yan, Weichao

2018-02-01

Natural gas hydrate is being considered as an alternative energy source for sustainable development and has become a focus of research throughout the world. In this paper, based on CT scanning images of hydrate reservoir rocks, combined with the microscopic distribution of hydrate, a diffusion limited aggregation (DLA) model was used to construct 3D hydrate digital rocks of different distribution types, and the finite-element method was used to simulate their electrical characteristics in order to study the influence of different hydrate distribution types, hydrate saturation and formation of water salinity on electrical properties. The results show that the hydrate digital rocks constructed using the DLA model can be used to characterize the microscopic distribution of different types of hydrates. Under the same conditions, the resistivity of the adhesive hydrate digital rock is higher than the cemented and scattered type digital rocks, and the resistivity of the scattered hydrate digital rock is the smallest among the three types. Besides, the difference in the resistivity of the different types of hydrate digital rocks increases with an increase in hydrate saturation, especially when the saturation is larger than 55%, and the rate of increase of each of the hydrate types is quite different. Similarly, the resistivity of the three hydrate types decreases with an increase in the formation of water salinity. The single distribution hydrate digital rock constructed, combined with the law of microscopic distribution and influence of saturation on the electrical properties, can effectively improve the accuracy of logging identification of hydrate reservoirs and is of great significance for the estimation of hydrate reserves.

Ion microprobe analyses of aluminous lunar glasses - A test of the 'rock type' hypothesis

Science.gov (United States)

Meyer, C., Jr.

1978-01-01

Previous soil survey investigations found that there are natural groupings of glass compositions in lunar soils and that the average major element composition of some of these groupings is the same at widely separated lunar landing sites. This led soil survey enthusiasts to promote the hypothesis that the average composition of glass groupings represents the composition of primary lunar 'rock types'. In this investigation the trace element composition of numerous aluminous glass particles was determined by the ion microprobe method as a test of the above mentioned 'rock type' hypothesis. It was found that within any grouping of aluminous lunar glasses by major element content, there is considerable scatter in the refractory trace element content. In addition, aluminous glasses grouped by major elements were found to have different average trace element contents at different sites (Apollo 15, 16 and Luna 20). This evidence argues that natural groupings in glass compositions are determined by regolith processes and may not represent the composition of primary lunar 'rock types'.

Nature, diversity of deposit types and metallogenic relations of South China

Science.gov (United States)

Zaw, K.; Peters, S.G.; Cromie, P.; Burrett, C.; Hou, Z.

2007-01-01

The South China Region is rich in mineral resources and has a wide diversity of deposit types. The region has undergone multiple tectonic and magmatic events and related metallogenic processes throughout the earth history. These tectonic and metallogenic processes were responsible for the formation of the diverse styles of base and precious metal deposits in South China making it one of the resource-rich regions in the world. During the Proterozoic, the South China Craton was characterised by rifting of continental margin before eruption of submarine volcanics and development of platform carbonate rocks, and the formation of VHMS, stratabound copper and MVT deposits. The Phanerozoic metallogeny of South China was related to opening and closing of the Tethyan Ocean involving multiple orogenies by subduction, back-arc rifting, arc-continent collision and post-collisional extension during the Indosinian (Triassic), Yanshanian (Jurassic to Cretaceous) and Himalayan (Tertiary) Orogenies. The Late Palaeozoic was a productive metallogenic period for South China resulting from break-up and rifting of Gondwana. Significant stratabound base and precious metal deposits were formed during the Devonian and Carboniferous (e.g., Fankou and Dabaoshan deposits). These Late Palaeozoic SEDEX-style deposits have been often overprinted by skarn systems associated with Yanshanian magmatism (e.g., Chengmenshan, Dongguashan and Qixiashan). A number of Late Palaeozoic to Early Mesozoic VHMS deposits also developed in the Sanjiang fold belt in the western part of South China (e.g., Laochang and Gacun). South China has significant sedimentary rock-hosted Carlin-like deposits, which occur in the Devonian- to Triassic-aged accretionary wedge or rift basins at the margin of the South China Craton. They are present in a region at the junction of Yunnan, Guizhou, and Guangxi Provinces called the 'Southern Golden Triangle', and are also present in NW Sichuan, Gansu and Shaanxi, in an area known as

Cooling of a polyethylene tunnel type greenhouse by means of a rock bed

Energy Technology Data Exchange (ETDEWEB)

Kurklu, Ahmet; Bilgin, Sefai [Akdeniz Univ., Dept. of Agricultural Mechanisation, Antalya (Turkey)

2004-10-01

An experiment was conducted to cool a 15 m{sup 2} ground area plastic-tunnel-type greenhouse by the use of a rock bed. An identical greenhouse with no rock bed was also erected for control purposes. Two rock-bed canals, each with the dimensions of 3 x l.25 x 0.75 m, were dug in the soil of the experimental greenhouse. After the canals were filled with the rocks and insulated, the top surface was covered by a soil layer of thickness enough for the root development depth of the plants. Air was pushed through the rock bed by a centrifugal fan with a 1100 m{sup 3}/h flow rate. Energy stored in the rock bed during the day was dumped outside the greenhouse at night using the cooler outside air. The results of the measurements showed that the rock-bed system maintained air temperature 14 deg C lower at maximum in the experimental greenhouse than the control one. The temperature difference seemed to increase with increasing solar radiation and outside air temperature. Relative humidity during the day remained at about 40% in the experimental greenhouse and was always higher than that in the control one. The coefficient of performance (COP) of the rock-bed system was higher than 3 in general, and it was observed that this value increased with decreasing rock-bed temperature. The average solar collection efficiency was 38%. The rock-bed system seems to have a significant potential for cooling applications in greenhouses. (Author)

Ore-forming environment and ore-forming system of carbonaceous-siliceous-pelitic rock type uranium deposit in China

International Nuclear Information System (INIS)

Qi Fucheng; Zhang Zilong; Li Zhixing; He Zhongbo; Wang Wenquan

2012-01-01

It is proposed that there are four types of ore-forming systems about carbonaceous-siliceous-pelitic rock type uranium deposit in China based on systematic study on structural environment and distribution regularity of uraniferous construction of marine carbonaceous-siliceous-pelitic rock in China: continental margin rift valley ore-forming systems, continental margin rifting deep fracture zone ore-forming systems, landmass boundary borderland basin ore-forming systems and epicontinental mobile belt downfaulted aulacogen ore-forming systems. It is propounded definitely that it is controlled by margin rift valley ore-forming systems and continental margin rifting deep fracture zone ore-forming systems for large-scale uranium mineralization of carbonaceous-siliceous-pelitic rock type uranium deposit in China, which is also controlled by uraniferous marine carbonaceous-siliceous-pelitic rock construction made up of silicalite, siliceous phosphorite and carbonaceous-siliceous-pelitic rock, which settled down accompany with submarine backwash and sub marine volcanic eruption in margin rift valley and continental margin rifting mineralizing environment. Continental mar gin rift valley and continental margin rifting thermal sedimentation or exhalation sedimentation is the mechanism of forming large-scale uraniferous marine carbonaceous-siliceous-pelitic rock construction Early Palaeozoic Era in China or large-scale uranium-polymetallic mineralization. (authors)

Bacteria diversity and arsenic mobilization in rock biofilm from an ancient gold and arsenic mine.

Science.gov (United States)

Tomczyk-Żak, Karolina; Kaczanowski, Szymon; Drewniak, Łukasz; Dmoch, Łukasz; Sklodowska, Aleksandra; Zielenkiewicz, Urszula

2013-09-01

In this paper we characterize the biofilm community from an ancient Złoty Stok gold and arsenic mine. Bacterial diversity was examined using a culture-independent technique based on 16S rRNA gene amplification, cloning and sequencing. We show that unexpectedly the microbial diversity of this community was extremely high (more than 190 OTUs detected), with the most numerous members from Rhizobiales (α-Proteobacteria). Although the level of rock biofilm diversity was similar to the microbial mat community we have previously characterized in the same adit, its taxonomic composition was completely different. Detailed analysis of functional arrA and aioA genes, chemical properties of siderophores found in pore water as well as the biofilm chemical composition suggest that the biofilm community contributes to arsenic pollution of surrounding water in a biogeochemical cycle similar to the one observed in bacterial mats. To interpret our results concerning the biological arsenic cycle, we applied the theory of ecological pyramids of Charles Elton. Copyright © 2013 Elsevier B.V. All rights reserved.

Fine-grained sheet silicate rocks

International Nuclear Information System (INIS)

Weaver, C.E.

1977-09-01

Considerable interest has been shown in the possibility of using shales as repositories for radioactive waste and a variety of other waste products, and it appears that over the next few years much money and effort will be expended to investigate and test a wide variety of shales. If shales are to be studied in detail by a large number of investigators, it is important that all concerned have the same concept of what constitutes a shale. The term shale and other terms for fine-grained rocks have been used for many years and have been continually redefined. Most definitions predate the development of modern instrumentation and are based on field observations and intuition; however, the main problem is the diversity of definitions. An attempt is made here to develop a simple, rational classification of fine-grained sediments, and it is hoped that this classification will eliminate some of the present ambiguity. In order that the classification be pertinent, mineral composition and textural data were compiled and evaluated. The data on unconsolidated and consolidated sediments were contrasted and the effects of burial diagenesis assessed. It was found necessary to introduce a new term, physil, to describe all sheet silicate minerals. In contrast to the term clay mineral, the term physil has no size connotation. A simple classification is proposed that is based on the percentage of physils and grain size. In Part II the fine-grained physil rocks are classified on the basis of physil type, non-physil minerals, and texture. Formations are listed which have the mineral and textural characteristics of the most important rock types volumetrically. Selected rock types, and the formations in which they can be found, are recommended for laboratory study to determine their suitability for the storage of high-level radioactive waste

Water - rock interaction in different rock environments

International Nuclear Information System (INIS)

Lamminen, S.

1995-01-01

The study assesses the groundwater geochemistry and geological environment of 44 study sites for radioactive waste disposal. Initially, the study sites were divided by rock type into 5 groups: (1) acid - intermediate rocks, (2) mafic - ultramafic rocks, (3) gabbros, amphibolites and gneisses that contain calc-silicate (skarn) rocks, (4) carbonates and (5) sandstones. Separate assessments are made of acid - intermediate plutonic rocks and of a subgroup that comprises migmatites, granite and mica gneiss. These all belong to the group of acid - intermediate rocks. Within the mafic -ultramafic rock group, a subgroup that comprises mafic - ultramafic plutonic rocks, serpentinites, mafic - ultramafic volcanic rocks and volcanic - sedimentary schists is also evaluated separately. Bedrock groundwaters are classified by their concentration of total dissolved solids as fresh, brackish, saline, strongly saline and brine-class groundwaters. (75 refs., 24 figs., 3 tabs.)

A computer-assisted rock type data catalogue for gas formations; Ein rechnergestuetzter Gesteinsdatenkatalog fuer Gasformationen

Energy Technology Data Exchange (ETDEWEB)

Reitenbach, V.; Pusch, G.; Moeller, M.; Koll, S. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik; Constantini, A.; Junker, A.; Anton, H. [RWE Dea AG, Hamburg (Germany)

2007-09-13

Modern reservoir management commonly requires versatile reservoir data which are neces-sary for integrated reservoir characterization, evaluation and development planning. The rock data necessary for numerical reservoir simulation studies often have to be collected from different sources, analysed and sorted with a considerable effort. In a framework of DGMK research program (DGMK project 593-9/4), the Institute of Petro-leum Engineering (Clausthal University of Technology) and RWE DEA AG have developed a new tool named Rock Data Catalogue, which is capable of managing large amounts of rock data more efficiently and deriving new specific correlations for European rock types. The use of Rock Data Catalogue can facilitate the essential input data generation and proc-essing procedure for reservoir simulation studies. The Rock Data Catalogue is comprised of a Data Base Module of digitalized reservoir rock data and an interactive Data Correlation Module. Both modules are built-up as an interface to common reservoir simulation software. The universal structure of the software also makes it possible to exchange the data with other rock data information systems. The Data Correlation Module implements a ''Decision-Structure'' module, which helps the reservoir engineer to select the rock data for analysis and correlation depending on its litho-facial type and permeability class. The Data Base Module enables a quick search of appro-priated data sets and their export into the correlation module. The open source data of the North German Rotliegend gas formations as well as the data of measurements on Rotliegend core samples performed at the ITE in course of the DGMK tight gas projects were implemented in the rock data base. Correlations of poro/perm data, two-phase flow and capillary pressure functions of the Rotliegend sandstones with the per-meability range between 20 and 0.01 mD are implemented in the rock data base and serve for quality checking of the

Petrology and geochemistry of mafic magmatic rocks from the Sarve-Abad ophiolites (Kurdistan region, Iran): Evidence for interaction between MORB-type asthenosphere and OIB-type components in the southern Neo-Tethys Ocean

Science.gov (United States)

Saccani, Emilio; Allahyari, Khalil; Rahimzadeh, Bahman

2014-05-01

The Sarve-Abad (Sawlava) ophiolites crop out in the Main Zagros Thrust Zone and represent remnants of the Mesozoic southern Neo-Tethys Ocean that was located between the Arabian shield and Sanandaj-Sirjan continental block. They consist of several incomplete ophiolitic sequences including gabbroic bodies, a dyke complex, and pillow lava sequences. These rocks generally range from sub-alkaline to transitional character. Mineral chemistry and whole-rock geochemistry indicate that they have compositions akin to enriched-type mid-ocean ridge basalts (E-MORB) and plume-type MORB (P-MORB). Nonetheless, the different depletion degrees in heavy rare earth elements (HREE), which can be observed in both E-MORB like and P-MORB like rocks enable two main basic chemical types of rocks to be distinguished as Type-I and Type-II. Type-I rocks are strongly depleted in HREE (YbN 9.0). Petrogenetic modeling shows that Type-I rocks originated from 7 to 16% polybaric partial melting of a MORB-type mantle source, which was significantly enriched by plume-type components. These rocks resulted from the mixing of variable fractions of melts generated in garnet-facies and the spinel-facies mantle. In contrast, Type-II rocks originated from 5 to 8% partial melting in the spinel-facies of a MORB-type source, which was moderately enriched by plume-type components. A possible tectono-magmatic model for the generation of the southern Neo-Tethys oceanic crust implies that the continental rift and subsequent oceanic spreading were associated with uprising of MORB-type asthenospheric mantle featuring plume-type component influences decreasing from deep to shallow mantle levels. These deep plume-type components were most likely inherited from Carboniferous mantle plume activity that was associated with the opening of Paleo-Tethys in the same area.

Preliminary state-of-the-art survey: mining techniques for salt and other rock types

Energy Technology Data Exchange (ETDEWEB)

1976-12-01

This is a systematic review of the state-of-the-art of underground mining and excavation technology in the U.S. as applied to salt, limestone, shale, and granite. Chapter 2 covers the basic characteristics of these rock types, the most frequently used underground mining methods, shaft and slope entry construction, equipment, and safety and productivity data. Chapters 3 and 4 summarize underground salt and limestone mining in the U.S. Chapter 5 shows that large amounts of thick shale exist in the U.S., but little is mined. Chapter 6 discusses underground excavations into granite-type rocks. Suggestions are given in the last chapter for further study. (DLC)

Site investigation SFR. Rock type coding, overview geological mapping and identification of rock units and possible deformation zones in drill cores from the construction of SFR

Energy Technology Data Exchange (ETDEWEB)

Petersson, Jesper (Vattenfall Power Consultant AB, Stockholm (Sweden)); Curtis, Philip; Bockgaard, Niclas (Golder Associates AB (Sweden)); Mattsson, Haakan (GeoVista AB, Luleaa (Sweden))

2011-01-15

This report presents the rock type coding, overview lithological mapping and identification of rock units and possible deformation zones in drill cores from 32 boreholes associated with the construction of SFR. This work can be seen as complementary to single-hole interpretations of other older SFR boreholes earlier reported in /Petersson and Andersson 2010/: KFR04, KFR08, KFR09, KFR13, KFR35, KFR36, KFR54, KFR55, KFR7A, KFR7B and KFR7C. Due to deficiencies in the available material, the necessary activities have deviated somewhat from the established methodologies used during the recent Forsmark site investigations for the final repository for spent nuclear fuel. The aim of the current work has been, wherever possible, to allow the incorporation of all relevant material from older boreholes in the ongoing SFR geological modelling work in spite of the deficiencies. The activities include: - Rock type coding of the original geological mapping according to the nomenclature used during the preceding Forsmark site investigation. As part of the Forsmark site investigation such rock type coding has already been performed on most of the old SFR boreholes if the original geological mapping results were available. This earlier work has been complemented by rock type coding on two further boreholes: KFR01 and KFR02. - Lithological overview mapping, including documentation of (1) rock types, (2) ductile and brittle-ductile deformation and (3) alteration for drill cores from eleven of the boreholes for which no original geological borehole mapping was available (KFR31, KFR32, KFR34, KFR37,KFR38, KFR51, KFR69, KFR70, KFR71, KFR72 and KFR89). - Identification of possible deformation zones and merging of similar rock types into rock units. This follows SKB's established criteria and methodology of the geological Single-hole interpretation (SHI) process wherever possible. Deviations from the standard SHI process are associated with the lack of data, for example BIPS images

Site investigation SFR. Rock type coding, overview geological mapping and identification of rock units and possible deformation zones in drill cores from the construction of SFR

International Nuclear Information System (INIS)

Petersson, Jesper; Curtis, Philip; Bockgaard, Niclas; Mattsson, Haakan

2011-01-01

This report presents the rock type coding, overview lithological mapping and identification of rock units and possible deformation zones in drill cores from 32 boreholes associated with the construction of SFR. This work can be seen as complementary to single-hole interpretations of other older SFR boreholes earlier reported in /Petersson and Andersson 2010/: KFR04, KFR08, KFR09, KFR13, KFR35, KFR36, KFR54, KFR55, KFR7A, KFR7B and KFR7C. Due to deficiencies in the available material, the necessary activities have deviated somewhat from the established methodologies used during the recent Forsmark site investigations for the final repository for spent nuclear fuel. The aim of the current work has been, wherever possible, to allow the incorporation of all relevant material from older boreholes in the ongoing SFR geological modelling work in spite of the deficiencies. The activities include: - Rock type coding of the original geological mapping according to the nomenclature used during the preceding Forsmark site investigation. As part of the Forsmark site investigation such rock type coding has already been performed on most of the old SFR boreholes if the original geological mapping results were available. This earlier work has been complemented by rock type coding on two further boreholes: KFR01 and KFR02. - Lithological overview mapping, including documentation of (1) rock types, (2) ductile and brittle-ductile deformation and (3) alteration for drill cores from eleven of the boreholes for which no original geological borehole mapping was available (KFR31, KFR32, KFR34, KFR37,KFR38, KFR51, KFR69, KFR70, KFR71, KFR72 and KFR89). - Identification of possible deformation zones and merging of similar rock types into rock units. This follows SKB's established criteria and methodology of the geological Single-hole interpretation (SHI) process wherever possible. Deviations from the standard SHI process are associated with the lack of data, for example BIPS images, or a

Application of Rock-Eval pyrolysis to the detection of hydrocarbon property in sandstone-type uranium deposits

International Nuclear Information System (INIS)

Sun Ye; Li Ziying; Guo Qingyin; Xiao Xinjian

2006-01-01

Rock-Eval pyrolysis is introduced into the research of uranium geology by means of oil-gas geochemical evaluation. Hydrocarbon (oil-gas) components in DS sandstone-type uranium deposit are detected quantitatively. Through analyzing the oil-gas bearing categories of the uranium-bearing sandstones, the internal relationships between the uranium deposit and the oil-gas are revealed. Rock-Eval pyrolysis is an effective method to study the interaction between inorganic and organic matters, and should be extended to the study of sandstone-type uranium deposits. (authors)

An review on geology study of carbonaceous-siliceous-pelitic rock type uranium deposit in China and the strategy for its development

International Nuclear Information System (INIS)

Zhao Fengmin

2009-01-01

Carbonaceous-siliceous-pelitic rock type uranium deposit was founded by Chinese uranium geologist, it refers to the uranium deposit hosted by non or light metamophosed carbonate,siliceous rock, pelitic rock and their intermediates. It is one of the important types uranium deposit in China. A lot of this type deposits have been discovered in China and their temporal-spatial distribution pattern and mineralization features have been basically identified, and the rich experience have layed a good foundation for the future exploration. Although the ore of this type is not favourable economically, it is still available. Because carbonaceous-siliceous-pelitic rock type uranium deposit has great resource potential, metallogenic study and exploration efforts should be projected differentially according to their economic profit so as to meet the uranium resource demand of nuclear power development in China. (authors)

Application feasibility study of evaluation technology for long-term rock behavior. 2. Parameter setting of variable compliance type model and application feasibility study for rock behavior evaluation

International Nuclear Information System (INIS)

Sato, Shin; Noda, Masaru; Niunoya, Sumio; Hata, Koji; Matsui, Hiroya; Mikake, Shinichiro

2012-01-01

Creep phenomenon is one of the long-term rock behaviors. In many of rock-creep studies, model and parameter have been verified in 2D analysis using model parameter acquired by uniaxial compression test etc considering rock types. Therefore, in this study model parameter was set by uniaxial compression test with classified rock samples which were taken from pilot boring when the main shaft was constructed. Then, comparison between measured value and 3D excavation analysis with identified parameter was made. By and large, the study showed that validity of identification methodology of parameter to identify reproduction of measured value and analysis method. (author)

Average contents of uranium and thorium in the most important types of rocks of the Ukrainian shield

International Nuclear Information System (INIS)

Belevtsev, Ya.N.; Egorov, Yu.P.; Titov, V.K.; Sukhinin, A.M.; Grechishnikova, Z. M.; Zayats, V.B.; Tikhonenko, V.A.; Zhukova, A.M.

1975-01-01

The data given concern uranium and thorium contents in the most important rock types of the Ukraina shield. The smallest quantities of uranium are characteristic for the vulcanic rocks of basic and ultrabasic rocks. Archean formations, whose source materials were mainly basic and ultrabasic vulcanites, are marked by this low uranium content. The highest uranium content is observed in the clastogenic rocks of low Proterozoic. The average uranium content is observed in silty argellite rocks represented by crystal slates and paragneissis. Rheomorphic and metasomatic granites and granosyenites of low and middle Proterozoic are also characterized by an increased content of uranium. The platform precipitation rocks of high Proterozoic possess a relatively low uranium content. Thorium concentrations with low thorium-uranium proportions in granites, syenites and granosyenites prove their enrichment in uranium

High Sr/Y rocks are not all adakites!

Science.gov (United States)

Moyen, Jean-François

2010-05-01

The name of "adakite" is used to describe a far too large group of rocks, whose sole common feature is high Sr/Y and La/Yb ratios. Defining adakites only by this criterion is misleading, as the definition of this group of rocks does include many other criteria, including major elements. In itself, high (or commonly moderate!) Sr/Y ratios can be achieved via different processes: melting of a high Sr/Y (and La/Yb) source; deep melting, with abundant residual garnet; fractional crystallization or AFC; or interactions of felsic melts with the mantle, causing selective enrichment in LREE and Sr over HREE. A database of the compositions of "adakitic" rocks - including "high silica" and "low silica" adakites, "continental" adakites and Archaean adakites—was assembled. Geochemical modeling of the potential processes is used to interpret it, and reveals that (1) the genesis of high-silica adakites requires high pressure evolution (be it by melting or fractionation), in equilibrium with large amounts of garnet; (2) low-silica adakites are explained by garnet-present melting of an adakite-metasomatized mantle, i.e at depths greater than 2.5 GPa; (3) "Continental" adakites is a term encompassing a huge range of rocks, with a corresponding diversity of petrogenetic processes, and most of them are different from both low- and high- silica adakites; in fact in many cases it is a complete misnomer and the rocks studied are high-K calc-alkaline granitoids or even S-type granites; (4) Archaean adakites show a bimodal composition range, with some very high Sr/Y examples (similar to part of the TTG suite) reflecting deep melting (> 2.0 GPa) of a basaltic source with a relatively high Sr/Y, while lower Sr/Y rocks formed by shallower (1.0 GPa) melting of similar sources. Comparison with the Archaean TTG suite highlights the heterogeneity of the TTGs, whose composition spreads the whole combined range of HSA and Archaean adakites, pointing to a diversity of sources and processes

Contribution of Alpha and Beta Diversity Across Land-Use Type to the Regional Diversity of Dung Beetles in Central Sulawesi

Directory of Open Access Journals (Sweden)

SHAHABUDDIN

2013-06-01

Full Text Available The importance of spatial scale has been acknowledged as one of determining factors of species diversity in local and regional diversity. The aim of this study was to evaluate contribution of alpha (α and beta (β diversity across land-use type to gamma (γ diversity at the margins of tropical forest in Central Sulawesi using dung beetles (Coleoptera: Scarabaeidae as a focal group. Baited pitfall traps set in four land-use types ranging from natural forest through cacao agroforestry systems to open areas during two years of sampling (2009 and 2012. A total of 28 dung beetle species belonging to four genera were captured during the study period. The results showed that contribution of β diversity was higher than that of α diversity of dung beetles. Each land-use type contributed about 56.5 to 62.5% of the total species richness (γ diversity. The similar pattern of biodiversity between each spatial scale and during the two sampling years emphasized the large contribution of each land-use type to maintaining a high portion of the regional species richness. It suggests the importance of managing other land-use types, such as secondary forest and agroforestry as well as protecting the remaining natural forests.

Hard-Rock Stability Analysis for Span Design in Entry-Type Excavations with Learning Classifiers

Directory of Open Access Journals (Sweden)

Esperanza García-Gonzalo

2016-06-01

Full Text Available The mining industry relies heavily on empirical analysis for design and prediction. An empirical design method, called the critical span graph, was developed specifically for rock stability analysis in entry-type excavations, based on an extensive case-history database of cut and fill mining in Canada. This empirical span design chart plots the critical span against rock mass rating for the observed case histories and has been accepted by many mining operations for the initial span design of cut and fill stopes. Different types of analysis have been used to classify the observed cases into stable, potentially unstable and unstable groups. The main purpose of this paper is to present a new method for defining rock stability areas of the critical span graph, which applies machine learning classifiers (support vector machine and extreme learning machine. The results show a reasonable correlation with previous guidelines. These machine learning methods are good tools for developing empirical methods, since they make no assumptions about the regression function. With this software, it is easy to add new field observations to a previous database, improving prediction output with the addition of data that consider the local conditions for each mine.

Hard-Rock Stability Analysis for Span Design in Entry-Type Excavations with Learning Classifiers.

Science.gov (United States)

García-Gonzalo, Esperanza; Fernández-Muñiz, Zulima; García Nieto, Paulino José; Bernardo Sánchez, Antonio; Menéndez Fernández, Marta

2016-06-29

The mining industry relies heavily on empirical analysis for design and prediction. An empirical design method, called the critical span graph, was developed specifically for rock stability analysis in entry-type excavations, based on an extensive case-history database of cut and fill mining in Canada. This empirical span design chart plots the critical span against rock mass rating for the observed case histories and has been accepted by many mining operations for the initial span design of cut and fill stopes. Different types of analysis have been used to classify the observed cases into stable, potentially unstable and unstable groups. The main purpose of this paper is to present a new method for defining rock stability areas of the critical span graph, which applies machine learning classifiers (support vector machine and extreme learning machine). The results show a reasonable correlation with previous guidelines. These machine learning methods are good tools for developing empirical methods, since they make no assumptions about the regression function. With this software, it is easy to add new field observations to a previous database, improving prediction output with the addition of data that consider the local conditions for each mine.

Phylogeny of rock-inhabiting fungi related to Dothideomycetes

NARCIS (Netherlands)

Ruibal, C.; Gueidan, C.; Selbmann, L.; Gorbushina, A.A.; Crous, P.W.; Groenewald, J.Z.; Muggia, L.; Grube, M.; Isola, D.; Schoch, C.L.; Staley, J.T.; Lutzoni, F.; Hoog, de G.S.

2009-01-01

The class Dothideomycetes (along with Eurotiomycetes) includes numerous rock-inhabiting fungi (RIF), a group of ascomycetes that tolerates surprisingly well harsh conditions prevailing on rock surfaces. Despite their convergent morphology and physiology, RIF are phylogenetically highly diverse in

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Science.gov (United States)

Suarez, Carlos J.; Smith, Brooke C.; Kramer, Brian R.; Ng, T. Terry; Ong, Lih-Yenn; Malcolm, Gerald N.

1993-01-01

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Global taxonomic diversity of anomodonts (tetrapoda, therapsida and the terrestrial rock record across the Permian-Triassic boundary.

Directory of Open Access Journals (Sweden)

Jörg Fröbisch

Full Text Available The end-Permian biotic crisis (~252.5 Ma represents the most severe extinction event in Earth's history. This paper investigates diversity patterns in Anomodontia, an extinct group of therapsid synapsids ('mammal-like reptiles', through time and in particular across this event. As herbivores and the dominant terrestrial tetrapods of their time, anomodonts play a central role in assessing the impact of the end-Permian extinction on terrestrial ecosystems. Taxonomic diversity analysis reveals that anomodonts experienced three distinct phases of diversification interrupted by the same number of extinctions, i.e. an end-Guadalupian, an end-Permian, and a mid-Triassic extinction. A positive correlation between the number of taxa and the number of formations per time interval shows that anomodont diversity is biased by the Permian-Triassic terrestrial rock record. Normalized diversity curves indicate that anomodont richness continuously declines from the Middle Permian to the Late Triassic, but also reveals all three extinction events. Taxonomic rates (origination and extinction indicate that the end-Guadalupian and end-Permian extinctions were driven by increased rates of extinction as well as low origination rates. However, this pattern is not evident at the final decline of anomodont diversity during the Middle Triassic. Therefore, it remains unclear whether the Middle Triassic extinction represents a gradual or abrupt event that is unique to anomodonts or more common among terrestrial tetrapods. The end-Permian extinction represents the most distinct event in terms of decline in anomodont richness and turnover rates.

Epigenetic alterations of sedimentary rocks at deposits

International Nuclear Information System (INIS)

Komarova, G.V.; Kondrat'eva, I.A.; Zelenova, O.I.

1980-01-01

Notions are explained, and technique for studying epigenetic alterations of sedimentary rocks at uranium deposits is described. Main types of epigenetic transformations and their mineralogic-geochemical characteristics are considered. Rock alterations, accompanying uranium mineralization, can be related to 2 types: oxidation and reduction. The main mineralogic-geochemical property of oxidation transformations is epigenetic limonitization. Stratal limonitization in primary grey-coloured terrigenic rocks and in epigenetically reduced (pyritized) rocks, as well as in rock, subjected to epigenetic gleying, are characterized. Reduction type of epigenetic transformations is subdivided into sulphidic and non-sulphidic (gley) subtypes. Sulphidic transformations in grey-coloured terrigenic rocks with organic substance of carbonic row, in rocks, containing organic substance of oil row, sulphide transformations of sedimentary rocks, as well as gley transformations, are considered

A survey of lunar rock types and comparison of the crusts of earth and moon

Science.gov (United States)

Wood, J. A.

1977-01-01

The principal known types of lunar rocks are briefly reviewed, and their chemical relationships discussed. In the suite of low-KREEP highland rocks, Fe/(Fe + Mg) in the normative mafic minerals increases and the albite content of normative plagio-clase decreases as the total amount of normative plagioclase increases, the opposite of the trend predicted by the Bowen reaction principle. The distribution of compositions of rocks from terrestrial layered mafic intrusives is substantially different: here the analyses fall in several discrete clusters (anorthositic rocks, norites, granophyres and ferrogabbros, ultramafics), and the chemical trends noted above are not reproduced. It is suggested that the observed trends in lunar highland rocks could be produced by crystal fractionation in a deep global surface magma system if (1) plagiociase tended to float, upon crystallization, and (2) the magma was kept agitated and well mixed (probably by thermal convection) until crystallization was far advanced and relatively little residual liquid was left. After the crustal system solidified, but before extensive cooling had developed a thick, strong lithosphere, mantle convection was able to draw portions of the lunar anorthositic crust down into the mantle.

Fluid and rock interaction in permeable volcanic rock

International Nuclear Information System (INIS)

Lindley, J.I.

1985-01-01

Four types of interrelated changes -geochemical, mineralogic, isotopic, and physical - occur in Oligocene volcanic units of the Mogollon-Datil volcanic field, New Mexico. These changes resulted from the operation of a geothermal system that, through fluid-rock interaction, affected 5 rhyolite ash-flow tuffs and an intercalated basaltic andesite lava flow causing a potassium metasomatism type of alteration. (1) Previous studies have shown enrichment of rocks in K 2 O as much as 130% of their original values at the expense of Na 2 O and CaO with an accompanying increase in Rb and decreases in MgO and Sr. (2) X-ray diffraction results of this study show that phenocrystic plagioclase and groundmass feldspar have been replaced with pure potassium feldspar and quartz in altered rock. Phenocrystic potassium feldspar, biotite, and quartz are unaffected. Pyroxene in basaltic andesite is replaced by iron oxide. (3) delta 18 O increases for rhyolitic units from values of 8-10 permil, typical of unaltered rock, to 13-15 permil, typical of altered rock. Basaltic andesite, however, shows opposite behavior with a delta 18 of 9 permil in unaltered rock and 6 permit in altered. (4) Alteration results in a density decrease. SEM revealed that replacement of plagioclase by fine-grained quartz and potassium feldspar is not a volume for volume replacement. Secondary porosity is created in the volcanics by the chaotic arrangement of secondary crystals

Statistical analysis of Thematic Mapper Simulator data for the geobotanical discrimination of rock types in southwest Oregon

Science.gov (United States)

Morrissey, L. A.; Weinstock, K. J.; Mouat, D. A.; Card, D. H.

1984-01-01

An evaluation of Thematic Mapper Simulator (TMS) data for the geobotanical discrimination of rock types based on vegetative cover characteristics is addressed in this research. A methodology for accomplishing this evaluation utilizing univariate and multivariate techniques is presented. TMS data acquired with a Daedalus DEI-1260 multispectral scanner were integrated with vegetation and geologic information for subsequent statistical analyses, which included a chi-square test, an analysis of variance, stepwise discriminant analysis, and Duncan's multiple range test. Results indicate that ultramafic rock types are spectrally separable from nonultramafics based on vegetative cover through the use of statistical analyses.

Improved characterization of reservoir behavior by integration of reservoir performances data and rock type distributions

Energy Technology Data Exchange (ETDEWEB)

Davies, D.K.; Vessell, R.K. [David K. Davies & Associates, Kingwood, TX (United States); Doublet, L.E. [Texas A& M Univ., College Station, TX (United States)] [and others

1997-08-01

An integrated geological/petrophysical and reservoir engineering study was performed for a large, mature waterflood project (>250 wells, {approximately}80% water cut) at the North Robertson (Clear Fork) Unit, Gaines County, Texas. The primary goal of the study was to develop an integrated reservoir description for {open_quotes}targeted{close_quotes} (economic) 10-acre (4-hectare) infill drilling and future recovery operations in a low permeability, carbonate (dolomite) reservoir. Integration of the results from geological/petrophysical studies and reservoir performance analyses provide a rapid and effective method for developing a comprehensive reservoir description. This reservoir description can be used for reservoir flow simulation, performance prediction, infill targeting, waterflood management, and for optimizing well developments (patterns, completions, and stimulations). The following analyses were performed as part of this study: (1) Geological/petrophysical analyses: (core and well log data) - {open_quotes}Rock typing{close_quotes} based on qualitative and quantitative visualization of pore-scale features. Reservoir layering based on {open_quotes}rock typing {close_quotes} and hydraulic flow units. Development of a {open_quotes}core-log{close_quotes} model to estimate permeability using porosity and other properties derived from well logs. The core-log model is based on {open_quotes}rock types.{close_quotes} (2) Engineering analyses: (production and injection history, well tests) Material balance decline type curve analyses to estimate total reservoir volume, formation flow characteristics (flow capacity, skin factor, and fracture half-length), and indications of well/boundary interference. Estimated ultimate recovery analyses to yield movable oil (or injectable water) volumes, as well as indications of well and boundary interference.

Rock.XML - Towards a library of rock physics models

Science.gov (United States)

Jensen, Erling Hugo; Hauge, Ragnar; Ulvmoen, Marit; Johansen, Tor Arne; Drottning, Åsmund

2016-08-01

Rock physics modelling provides tools for correlating physical properties of rocks and their constituents to the geophysical observations we measure on a larger scale. Many different theoretical and empirical models exist, to cover the range of different types of rocks. However, upon reviewing these, we see that they are all built around a few main concepts. Based on this observation, we propose a format for digitally storing the specifications for rock physics models which we have named Rock.XML. It does not only contain data about the various constituents, but also the theories and how they are used to combine these building blocks to make a representative model for a particular rock. The format is based on the Extensible Markup Language XML, making it flexible enough to handle complex models as well as scalable towards extending it with new theories and models. This technology has great advantages as far as documenting and exchanging models in an unambiguous way between people and between software. Rock.XML can become a platform for creating a library of rock physics models; making them more accessible to everyone.

Biodeterioration agents: Bacterial and fungal diversity dwelling in or on the pre-historic rock-paints of Kabra-pahad, India.

Science.gov (United States)

Biswas, Jayant; Sharma, Kavita; Harris, K K; Rajput, Yogita

2013-09-01

In the last few decades, losses of our cultural heritage due to biodeteriorationare beinghighly recognized. From museum objects to rock monuments, the microbial biodeterioration agents are found to be the most destructive. Possibilities for proper preservative measure(s) are always more when it is only a monument, statue, museum article, or pre-historic art in any small subterranean cave. Nevertheless, preservation/protection of the footprints occupying a big area, lying scattered in a very negligible manner requires safeguard against several deterioration factors; right from various physical, chemical and biological agents which are indeed interrelated to each other. In the present study, some microbial communities possibly responsible for deteriorating the rocks of Kabra-pahad, where the most famous pre-historic rock paints of India prevail have been identified. The diversity of fungi and bacteria present in the stone crust of the infected areas has been studied by employing standard laboratory methods. The cultivated cultures confirmed total fifteen fungal species, among which Aspergillus group were the most dominant. Among bacteria, total 80 numbers of colonies were observed that dominated by two major groups; Micrococcus.spp and Staphylococcus spp. The pre-historic footprint in the form of rock paints in Kabra-pahad of district Raigarh, Chhattisgarh, India is lying in a very deteriorated manner. In the present study, we have tried to identify few major deteriorating factors that are responsible for such degradation of our existing pre-historic footprints.

Genetic diversity in three morphological types of Astragalus ...

African Journals Online (AJOL)

STORAGESEVER

2009-09-15

Sep 15, 2009 ... high genetic diversity suggested that each type had a potential to develop new strains or cultivars and .... herbs and widespread distributed species (Yao et al.,. 2008) ... 1) A. membranaceus var. mongholicus is a cross-.

Detrital Zircons From the Jack Hills and Mount Narryer, Western Australia: Geochronological, Morphological, and Geochemical Evidence for Diverse >4000 Ma Source Rocks

Science.gov (United States)

Crowley, J. L.; Myers, J. S.; Sylvester, P. J.; Cox, R. A.

2004-05-01

Detrital zircons from all major clastic units in the Jack Hills and Mount Narryer metasedimentary belts, Western Australia, were analyzed for morphology, internal zoning, inclusion mineralogy, age, and trace element concentrations (latter two obtained by laser-ablation microprobe ICPMS). The results show that zircons were derived from a wide diversity of rocks, including previously described, >4000 Ma grains that are older than any known terrestrial rocks. In three metaconglomerate samples from the western Jack Hills, 4200-3800 Ma zircons ("old grains") comprise 14% of the population, 3800-3600 Ma grains form only 2%, and 3550-3250 Ma zircons ("young grains") are dominant with a significant peak at 3380 Ma. Old and young grains are interpreted as being from similar rock types because they are indistinguishable in trace element concentrations, size (several hundred microns), morphology (subequant, typically fragmented), internal zoning (typically both oscillatory and sector), and U concentration (50-200 ppm). Many of these properties suggest an intermediate plutonic source, whereas an evolved granitic source was previously interpreted from rare-earth element and oxygen isotope data. Detrital zircons in quartzites and metaconglomerates at Mount Narryer differ significantly from zircons from the western Jack Hills. Old grains comprise only 3% (most of which are 4200-4100 Ma), 3800-3600 Ma zircons form 31%, and there are peaks at 3650, 3600, and 3500 Ma. Old and young grains have similar properties that suggest granitic sources, such as elongate prismatic morphology, oscillatory zoning, high U concentrations (100-600 ppm), and xenotime and monazite inclusions. Trace element concentrations are broadly similar to those in Jack Hills zircons, with notable exceptions being generally higher U, smaller Ce and Eu anomalies, and lower Nb/Ta. It is considered unlikely that Jack Hills zircons were derived from granitic gneisses that surround the metasedimentary belts because

Spatial pattern of tree diversity and evenness across forest types in Majella National Park, Italy

Directory of Open Access Journals (Sweden)

Mohammad Redowan

2015-09-01

Full Text Available Background Estimation of tree diversity at broader scale is important for conservation planning. Tree diversity should be measured and understood in terms of diversity and evenness, two integral components to describe the structure of a biological community. Variation of the tree diversity and evenness with elevation, topographic relief, aspect, terrain shape, slope, soil nutrient, solar radiation etc. are well documented. Methods Present study explores the variation of tree diversity (measured as Shannon diversity and evenness indices of Majella National Park, Italy with five available forest types namely evergreen oak woods, deciduous oak woods, black/aleppo pine stands, hop-hornbeam forest and beech forest, using satellite, environmental and field data. Results Hop-hornbeam forest was found to be most diverse and even while evergreen Oak woods was the lowest diverse and even. Diversity and evenness of forest types were concurrent to each other i.e. forest type which was more diverse was also more even. As a broad pattern, majority portion of the study area belonged to medium diversity and high evenness class. Conclusions Satellite images and other GIS data proved useful tools in monitoring variation of tree diversity and evenness across various forest types. Present study findings may have implications in prioritizing conservation zones of high tree diversity at Majella.

Disc cutter wear and rock texture in hard rock TBM tunneling

International Nuclear Information System (INIS)

Koizumi, Yu; Tsusaka, Kimikazu; Tanimoto, Chikaosa; Nakagawa, Shigeo; Fujita, Naoya

2008-01-01

Disc cutter wear in TBM tunneling is caused by initial fragmentation of a solid rock face (the primary fragmentation) and fragmentation of residual rock pieces between a cutterhead and the face (the secondary fragmentation). In two projects through sedimentary and granitic rocks, the authors investigated the relationships between the rate of cutter wear caused by the primary fragmentation, point load index and the grain size and contents of abrasive minerals. As a result, it was found that the tensile strength and the mineral contents of rocks significantly influenced the cutter wear in both projects and thus it is necessary to take into account of rock type. (author)

Hydrological characteristics of Japanese rock

International Nuclear Information System (INIS)

Ijiri, Yuji; Sawada, Atsushi; Akahori, Kuniaki

1999-11-01

It is crucial to evaluate the hydrogeological characteristics of rock in Japan in order to assess the performance of geosphere. This report summarizes the hydrogeological characteristics of various rock types obtained from broad literature surveys and the fields experiments at the Kamaishi mine in northern Japan and at the Tono mine in central Japan. It is found that the hydraulic conductivity of rock mass ranges from 10 -9 m/s to 10 -8 m/s, whereas the hydraulic conductivity of fault zone ranges from 10 -9 m/s to 10 -3 m/s. It is also found that the hydraulic conductivity tends to decrease with depth. Therefore, the hydraulic conductivity of rock mass at the depth of a repository will be smaller than above values. From the investigations at outcrops and galleries throughout the country, fractures are observed as potential pathways in all rock types. All kinds of crystalline rocks and pre-Neogene sedimentary rocks are classified as fractured media where fracture flow is dominant. Among these rocks, granitic rock is considered the archetype fractured media. On the other hand, andesite, tuff and Neogene sedimentary rocks are considered as intermediate between fractured media and porous media where flow in fractures as well as in rock matrix are significant. (author)

Rock properties data base

Energy Technology Data Exchange (ETDEWEB)

Jackson, R.; Gorski, B.; Gyenge, M.

1991-03-01

As mining companies proceed deeper and into areas whose stability is threatened by high and complex stress fields, the science of rock mechanics becomes invaluable in designing underground mine strata control programs. CANMET's Mining Research Laboratories division has compiled a summary of pre- and post-failure mechanical properties of rock types which were tested to provide design data. The 'Rock Properties Data Base' presents the results of these tests, and includes many rock types typical of Canadian mine environments. The data base also contains 'm' and 's' values determined using Hoek and Brown's failure criteria for both pre- and post-failure conditions. 7 refs., 3 tabs., 9 figs., 1 append.

Relationships between data from Rock-Eval pyrolysis and proximate, ultimate, petrographic, and physical analyses of 142 diverse U.S. coal samples

Science.gov (United States)

Bostick, N.H.; Daws, T.A.

1994-01-01

Basic research on coal and oil shale led to automated pyrolysis analysis of petroleum source rocks; most widely used is the Rock-Eval equipment. In order to interpret Rock-Eval analyses in relation to traditional coal data, we analyzed 142 commercial coals with diverse rank, age, maceral and sulfur contents, for most regions of the United States. We compared the Rock-Eval data with traditional industrial coal data, including volatile matter, calorific value, hydrogen and oxygen content, free swelling index, and vitrinite reflectance. We found: (1) there is a close relationship between Tmax and vitrinite reflectance in the ranges 420-590??C Tmax and 0.4-3%Romax of most coals. (2) A close relationship between Tmax and volatile matter (%VM) extends through the entire sample range, including low-rank samples with 35-70% VM, a range where %VM is not considered to be a useful rank parameter. (3) TOC of medium- and high-rank coals is seriously under-measured by Rock-Eval; TOC of low-rank coals (less than 0.8%Romax) is close to "dry basis" carbon from ultimate analysis. (4) The direct relationships between oxygen index (OI) and %O and between hydrogen index (HI) and %H are clear, though only broadly defined. However, there is virtually no band of concentrated data points on the HI versus OI pseudo-Van Krevelen diagram comparable to the "development line" on the H/C versus O/C diagram. (5) There are systematic relationships between Rock-Eval and industrial coal parameters such as calorific value and FSI, but much standardization would be needed before Rock-Eval could find a place in the coal industry. Tests with blends of coal and quartz sand and with various loads of coal alone showed that the amount of organic matter in the Rock-Eval load greatly influences results. Total load in the crucible, if largely inert, plays a small role, however. Increasing absolute or relative coal content causes under-evaluation of Rock-Eval TOC and over-rating of hydrogen. Blends of several

Clonal diversity and clone formation in the parthenogenetic Caucasian rock Lizard Darevskia dahli [corrected].

Science.gov (United States)

Vergun, Andrey A; Martirosyan, Irena A; Semyenova, Seraphima K; Omelchenko, Andrey V; Petrosyan, Varos G; Lazebny, Oleg E; Tokarskaya, Olga N; Korchagin, Vitaly I; Ryskov, Alexey P

2014-01-01

The all-female Caucasian rock lizard species Darevskia dahli and other parthenogenetic species of this genus reproduce normally via true parthenogenesis. Previously, the genetic diversity of this species was analyzed using allozymes, mitochondrial DNA, and DNA fingerprint markers. In the present study, variation at three microsatellite loci was studied in 111 specimens of D. dahli from five populations from Armenia, and new information regarding clonal diversity and clone formation in D. dahli was obtained that suggests a multiple hybridization origin. All individuals but one were heterozygous at the loci studied. Based on specific allele combinations, 11 genotypes were identified among the individuals studied. Individuals with the same genotypes formed distinct clonal lineages: one major clone was represented by 72 individuals, an intermediate clone was represented by 21 individuals, and nine other clones were rare and represented by one or several individuals. A new approach based on the detection and comparison of genotype-specific markers formed by combinations of parental-specific markers was developed and used to identify at least three hybridization founder events that resulted in the initial formation of one major and two rare clones. All other clones, including the intermediate and seven rare clones, probably arose through postformation microsatellite mutations of the major clone. This approach can be used to identify hybridization founder events and to study clone formation in other unisexual taxa.

A chemical redox reaction to generate rock salt-type materials: the case of Na3V2O5.

Science.gov (United States)

Adamczyk, E; Anger, E; Freire, M; Pralong, V

2018-02-27

Chemical redox reactions are extremely efficient to prepare fully reduced or oxidized phases that are formed during the topotactic insertion/extraction of alkaline ions. Herein, we report these reactions and discuss the possibility to generate new ordered or disordered rock salt-type structures depending on the structure of the mother phase. We have shown that a disordered rock salt-type structure is formed when the transition element is located at the tetrahedral site, as exemplified by the formation of Na 3 V 2 O 5 upon chemical reduction of V 2 O 5 .

An Integrated Rock Typing Approach for Unraveling the Reservoir Heterogeneity of Tight Sands in the Whicher Range Field of Perth Basin, Western Australia

DEFF Research Database (Denmark)

Ilkhchi, Rahim Kadkhodaie; Rezaee, Reza; Harami, Reza Moussavi

2014-01-01

Tight gas sands in Whicher Range Field of Perth Basin show large heterogeneity in reservoir characteristics and production behavior related to depositional and diagenetic features. Diagenetic events (compaction and cementation) have severely affected the pore system. In order to investigate...... the petrophysical characteristics, reservoir sandstone facies were correlated with core porosity and permeability and their equivalent well log responses to describe hydraulic flow units and electrofacies, respectively. Thus, very tight, tight, and sub-tight sands were differentiated. To reveal the relationship...... between pore system properties and depositional and diagenetic characteristics in each sand type, reservoir rock types were extracted. The identified reservoir rock types are in fact a reflection of internal reservoir heterogeneity related to pore system properties. All reservoir rock types...

Source rock

Directory of Open Access Journals (Sweden)

Abubakr F. Makky

2014-03-01

Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

Migmatites and migmatite-like rocks of Olkiluoto

International Nuclear Information System (INIS)

Kaerki, A.

2015-02-01

Bedrock of the Olkiluoto Island in the western end of the Palaeoproterozoic Svecofennian Accretionary Arc Complex, SW Finland is composed of high-grade metamorphic pelites, arenites and intermediate, arc type metavolcanic rocks intruded by granodioritic to tonalitic plutonic rocks. Regional metamorphism culminated with voluminous migmatization in the temperature of 660 - 700 deg C and relatively low pressure of about 3.5 - 4 kbar. The end result of polyphase metamorphism and deformation is a metamorphic rock succession composed of diverse migmatite rocks, metatexites and diatexites. Metatexites are migmatites in which several, discrete components can be detected, and in which the paleosome with some pre-partial-melting textures is identifiable. Diatexites are more advanced migmatites in which the pre-migmatization structures are often totally destroyed and the rock is dominated by different neosome components meaning leucosome, melanosome or mesosome. Based on the migmatite structures the metatexites of Olkiluoto have been classified into six subgroups. Dike-structured metatexites are composed of well preserved paleosome intruded by one single set of narrow, subparallel leucosome dikes which cover ca. 5 - 10 % of the whole rock volume. Net-structure is composed of a network of narrow leucosome dikes which show a reticulated structure in a plane section and cover less than 30 % of the whole rock volume. Breccia-structure is composed of angular or rounded paleosome blocks surrounded by moderate amount of leucosome. Patch-structure is composed of irregular leucosome patches which intruded the well preserved paleosome and compose typically 20 - 70 % of the rock volume. Layer-structure is characterized by more or less regular leucosome dikes sub-parallel to the foliation of the well preserved paleosome. Vein-structured metatexites and also diatexites include a set of pipe-like, longish leucosome veins most probably generated by synchronous melting and deformation

Migmatites and migmatite-like rocks of Olkiluoto

Energy Technology Data Exchange (ETDEWEB)

Kaerki, A. [Kivitieto Oy, Oulu (Finland)

2015-02-15

Bedrock of the Olkiluoto Island in the western end of the Palaeoproterozoic Svecofennian Accretionary Arc Complex, SW Finland is composed of high-grade metamorphic pelites, arenites and intermediate, arc type metavolcanic rocks intruded by granodioritic to tonalitic plutonic rocks. Regional metamorphism culminated with voluminous migmatization in the temperature of 660 - 700 deg C and relatively low pressure of about 3.5 - 4 kbar. The end result of polyphase metamorphism and deformation is a metamorphic rock succession composed of diverse migmatite rocks, metatexites and diatexites. Metatexites are migmatites in which several, discrete components can be detected, and in which the paleosome with some pre-partial-melting textures is identifiable. Diatexites are more advanced migmatites in which the pre-migmatization structures are often totally destroyed and the rock is dominated by different neosome components meaning leucosome, melanosome or mesosome. Based on the migmatite structures the metatexites of Olkiluoto have been classified into six subgroups. Dike-structured metatexites are composed of well preserved paleosome intruded by one single set of narrow, subparallel leucosome dikes which cover ca. 5 - 10 % of the whole rock volume. Net-structure is composed of a network of narrow leucosome dikes which show a reticulated structure in a plane section and cover less than 30 % of the whole rock volume. Breccia-structure is composed of angular or rounded paleosome blocks surrounded by moderate amount of leucosome. Patch-structure is composed of irregular leucosome patches which intruded the well preserved paleosome and compose typically 20 - 70 % of the rock volume. Layer-structure is characterized by more or less regular leucosome dikes sub-parallel to the foliation of the well preserved paleosome. Vein-structured metatexites and also diatexites include a set of pipe-like, longish leucosome veins most probably generated by synchronous melting and deformation

Rock Slope Design Criteria

Science.gov (United States)

2010-06-01

Based on the stratigraphy and the type of slope stability problems, the flat lying, Paleozoic age, sedimentary : rocks of Ohio were divided into three design units: 1) competent rock design unit consisting of sandstones, limestones, : and siltstones ...

Rock types and ductile structures on a rock domain basis, and fracture orientation and mineralogy on a deformation zone basis. Preliminary site description. Forsmark area - version 1.2

Energy Technology Data Exchange (ETDEWEB)

Stephens, Michael [Geological Survey of Sweden, Uppsala (Sweden); Forssberg, Ola [Golder Associates AB, Uppsala (Sweden)

2006-09-15

This report presents the results of the analysis of base geological data in order to establish the dominant rock type, the subordinate rock types and the orientation of ductile mineral fabrics within each rock domain included in the regional geological model, version 1.2. An assessment of the degree of homogeneity of each domain is also provided. The analytical work has utilised the presentation of data in the form of histograms and stereographic projections. Fisher means and K values or best-fit great circles and corresponding pole values have been calculated for the ductile structural data. These values have been used in the geometric modelling of rock domains in the regional model, version 1.2. Furthermore, all analytical results have been used in the assignment of properties to rock domains in this model. A second analytical component reported here addresses the orientation and mineralogy of fractures in the deterministic deformation zones that are included in the regional geological model, version 1.2. The analytical work has once again utilised the presentation of data in the form of histograms and stereographic projections. Fisher means and K values are presented for the orientation of fracture sets in the deterministic deformation zones that have been identified with the help of new borehole data. The frequencies of occurrence of different minerals along the fractures in these deformation zones as well as the orientation of fractures in the zones, along which different minerals occur, are also presented. The results of the analyses have been used in the establishment of a conceptual structural model for the Forsmark site and in the assignment of properties to deterministic deformation zones in model version 1.2.

Geology and porphyry copper-type alteration-mineralization of igneous rocks at the Christmas Mine, Gila County, Arizona

Science.gov (United States)

Koski, Randolph A.

1979-01-01

The Christmas copper deposit, located in southern Gila County, Arizona, is part of the major porphyry copper province of southwestern North America. Although Christmas is known for skarn deposits in Paleozoic carbonate rocks, ore-grade porphyry-type copper mineralization also occurs in a composite granodioritic intrusive complex and adjacent mafic volcanic country rocks. This study considers the nature, distribution, and genesis of alteration-mineralization in the igneous rock environment at Christmas. At the southeast end of the Dripping Spring Mountains, the Pennsylvanian Naco Limestone is unconformably overlain by the Cretaceous Williamson Canyon Volcanics, a westward-thinning sequence of basaltic volcanic breccia and lava flows, and subordinate clastic sedimentary rocks. Paleozoic and Mesozoic strata are intruded by Laramide-age dikes, sills, and small stocks of hornblende andesite porphyry and hornblende rhyodacite porphyry, and the mineralized Christmas intrusive complex. Rocks of the elongate Christmas stock, intruded along an east-northeast-trending fracture zone, are grouped into early, veined quartz diorite (Dark Phase), biotite granodiorite porphyry (Light Phase), and granodiorite; and late, unveined dacite porphyry and granodiorite porphyry. Biotite rhyodacite porphyry dikes extending east and west from the vicinity of the stock are probably coeval with biotite granodiorite porphyry. Accumulated normal displacement of approximately 1 km along the northwest-trending Christmas-Joker fault system has juxtaposed contrasting levels (lower, intrusive-carbonate rock environment and upper, intrusive-volcanic rock environment) within the porphyry copper system. K-Ar age determinations and whole-rock chemical analyses of the major intrusive rock types indicate that Laramide calc-alkaline magmatism and ore deposition at Christmas evolved over an extended period from within the Late Cretaceous (~75-80 m.y. ago) to early Paleocene (~63-61 m.y. ago). The sequence of

Evaluation of Rock Bolt Support for Polish Hard Rock Mines

Science.gov (United States)

Skrzypkowski, Krzysztof

2018-03-01

The article presents different types of rock bolt support used in Polish ore mining. Individual point resin and expansion rock bolt support were characterized. The roof classes for zinc and lead and copper ore mines were presented. Furthermore, in the article laboratory tests of point resin rock bolt support in a geometric scale of 1:1 with minimal fixing length of 0.6 m were made. Static testing of point resin rock bolt support were carried out on a laboratory test facility of Department of Underground Mining which simulate mine conditions for Polish ore and hard coal mining. Laboratory tests of point resin bolts were carried out, especially for the ZGH Bolesław, zinc and lead "Olkusz - Pomorzany" mine. The primary aim of the research was to check whether at the anchoring point length of 0.6 m by means of one and a half resin cartridge, the type bolt "Olkusz - 20A" is able to overcome the load.The second purpose of the study was to obtain load - displacement characteristic with determination of the elastic and plastic range of the bolt. For the best simulation of mine conditions the station steel cylinders with an external diameter of 0.1 m and a length of 0.6 m with a core of rock from the roof of the underground excavations were used.

Rare earth element mobility in arc-type volcanic rocks

International Nuclear Information System (INIS)

Kuschel, E.; Smith, I.E.M.

1990-01-01

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. It is emphasised that the pattern of REE mobility in young, fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits. 3 refs., 5 figs

Integration of rock physical signatures with depositional environments: A case study from East Coast of India

Science.gov (United States)

Mondal, Samit; Yadav, Ashok; Chatterjee, Rima

2018-01-01

Rock physical crossplots from different geological setup along eastern continental margin of India (ECMI) represent diversified signatures. To characterize the reservoirs in rock physics domain (velocity/modulus versus porosity) and then connecting the interpretation with geological model has been the objectives of the present study. Petrophysical logs (total porosity and volume of shale) from five wells located at sedimentary basins of ECMI have been analyzed to quantify the types of shale such as: laminated, dispersed and structural in reservoir. Presence of various shale types belonging to different depositional environments is coupled to define distinct rock physical crossplot trends for different geological setup. Wells from three different basins in East Coast of India have been used to capture diversity in depositional environments. Contact model theory has been applied to the crossplot to examine the change in rock velocity with change in reservoir properties like porosity and volume of shale. The depositional and diagenetic trends have been shown in the crossplot to showcase the prime controlling factor which reduces the reservoir porosity. Apart from that, the effect of geological factors like effective stress, sorting, packing, grain size uniformity on reservoir properties have also been focused. The rock physical signatures for distinct depositional environments, effect of crucial geological factors on crossplot trends coupled with established sedimentological models in drilled area are investigated to reduce the uncertainties in reservoir characterization for undrilled potentials.

The siliceous-calcareous-argillaceous rock type uranium deposit in south subzone of Western Qinling

International Nuclear Information System (INIS)

Qian Farong; Zhou Dean; Ji Hongfang

1995-11-01

The siliceous-calcareous-argillaceous rock type uranium deposit in south subzone of western Qinling is an inland found type deposit with specific mineralization and good potentiality. The mineralization distributes along definite horizons and occurs in siliceous layer and lenses of siliceous-calcareous rocks. Orebody presents in forms of stratoid, lenticular and irregular veins and controlled by factorial structures. Ore is identified as massive and sandy and each characterized by various mineral compositions and element associations. The study shows that the mineralizing materials are mainly derived from ore-bearing strata. The metallogenic environment has characteristics of middle-low temperature and supergene The metallogenesis underwent three stages: (1) Sedimentation-diagenesis of the ore-bearing strata led to preliminary concentration of uranium; (2) Polytectonic activities accompanied by underground hydrothermal process resulted in the industrial concentration of uranium; and (3) Orebody reworked by oxidation-denudation and leaching, locally has taken place secondary concentration. The deposit in origin attributes to polygenesis dominated by underground hydrothermal metallogenesis. Main metallogenic epoch happens during the periods of Late Yanshan and Himalayan. According to the geological-tectonic conditions the further prospecting direction in study area is proposed. (3 refs., 5 figs., 9 tabs.)

Critical issues in soft rocks

OpenAIRE

Milton Assis Kanji

2014-01-01

This paper discusses several efforts made to study and investigate soft rocks, as well as their physico-mechanical characteristics recognized up to now, the problems in their sampling and testing, and the possibility of its reproduction through artificially made soft rocks. The problems in utilizing current and widespread classification systems to some types of weak rocks are also discussed, as well as other problems related to them. Some examples of engineering works in soft rock or in soft ...

Rock strength under explosive loading

International Nuclear Information System (INIS)

Rimer, N.; Proffer, W.

1993-01-01

This presentation emphasizes the importance of a detailed description of the nonlinear deviatoric (strength) response of the surrounding rock in the numerical simulation of underground nuclear explosion phenomenology to the late times needed for test ban monitoring applications. We will show how numerical simulations which match ground motion measurements in volcanic tuffs and in granite use the strength values obtained from laboratory measurements on small core samples of these rocks but also require much lower strength values after the ground motion has interacted with the rock. The underlying physical mechanisms for the implied strength reduction are not yet well understood, and in fact may depend on the particular rock type. However, constitutive models for shock damage and/or effective stress have been used successfully at S-Cubed in both the Geophysics Program (primarily for DARPA) and the Containment Support Program (for DNA) to simulate late time ground motions measured at NTS in many different rock types

Microclimate and limits to photosynthesis in a diverse community of hypolithic cyanobacteria in northern Australia

Science.gov (United States)

Tracy, Christopher R.; Streten-Joyce, Claire; Dalton, Robert; Nussear, Kenneth E.; Gibb, Karen S.; Christian, Keith A.

2010-01-01

Hypolithic microbes, primarily cyanobacteria, inhabit the highly specialized microhabitats under translucent rocks in extreme environments. Here we report findings from hypolithic cyanobacteria found under three types of translucent rocks (quartz, prehnite, agate) in a semiarid region of tropical Australia. We investigated the photosynthetic responses of the cyanobacterial communities to light, temperature and moisture in the laboratory, and we measured the microclimatic variables of temperature and soil moisture under rocks in the field over an annual cycle. We also used molecular techniques to explore the diversity of hypolithic cyanobacteria in this community and their phylogenetic relationships within the context of hypolithic cyanobacteria from other continents. Based on the laboratory experiments, photosynthetic activity required a minimum soil moisture of 15% (by mass). Peak photosynthetic activity occurred between approximately 8°C and 42°C, though some photosynthesis occurred between −1°C and 51°C. Maximum photosynthesis rates also occurred at light levels of approximately 150–550 μmol m−2 s−1. We used the field microclimatic data in conjunction with these measurements of photosynthetic efficiency to estimate the amount of time the hypolithic cyanobacteria could be photosynthetically active in the field. Based on these data, we estimated that conditions were appropriate for photosynthetic activity for approximately 942 h (∼75 days) during the year. The hypolithic cyanobacteria community under quartz, prehnite and agate rocks was quite diverse both within and between rock types. We identified 115 operational taxonomic units (OTUs), with each rock hosting 8–24 OTUs. A third of the cyanobacteria OTUs from northern Australia grouped with Chroococcidiopsis, a genus that has been identified from hypolithic and endolithic communities from the Gobi, Mojave, Atacama and Antarctic deserts. Several OTUs identified from northern Australia have

Assessment of landscape diversity and determination of landscape hotspots - a case of Slovenia

Science.gov (United States)

Perko, Drago; Ciglič, Rok; Hrvatin, Mauro

2017-04-01

Areas with high landscape diversity can be regarded as landscape hotspots, and vice versa areas with low landscape diversity can be marked as landscape coldspots. The main purpose of this paper is to use quantitative geoinformatical approach and identify parts of our test area (the country of Slovenia) that can be described as very diverse according to natural landscapes and natural elements. We used different digital raster data of natural elements and landscape classifications and defined landscape diversity and landscape hotspots. We defined diversity for each raster pixel by counting the number of different unique types of landscape elements and types of landscapes in its neighborhood. Namely, the method was used separately to define diversity according to natural elements (types of relief forms, rocks, and vegetation) and diversity according to existing geographical landscape classifications of Slovenia (types of landscapes). In both cases one-tenth of Slovenia's surface with the highest landscape diversity was defined as landscape hotspots. The same applies to the coldspots. Additionally we tested the same method of counting different types of landscapes in certain radius also for the area of Europe in order to find areas that are more diverse at continental level. By doing so we were able to find areas that have similar level of diversity as Slovenia according to different European landscape classifications. Areas with landscape diversity may have an advantage in economic development, especially in tourism. Such areas are also important for biodiversity, habitat, and species diversity. On the other hand, localities where various natural influences mix can also be areas where it is hard to transfer best practices from one place to another because of the varying responses of the landscapes to human intervention. Thus it is important to know where areas with high landscape diversity are.

Rock-degrading endophytic bacteria in cacti

Science.gov (United States)

M. Esther Puente; Ching Y. Li; Yoav Bashan

2009-01-01

A plant-bacterium association of the cardon cactus (Pachycereus pringlei) and endophytic bacteria promotes establishment of seedlings and growth on igneous rocks without soil. These bacteria weather several rock types and minerals, unbind significant amounts of useful minerals for plants from the rocks, fix in vitro N2. produce...

Ore-controlling mechanism of carbonaceous-siliceous-pelitic rock type uranium deposits with down-faulted red basins in the southeast continental margin of Yangtze plate

International Nuclear Information System (INIS)

Zhang Zilong; Qi Fucheng; He Zhongbo; Li Zhixing; Wang Wenquan; Yu Jinshui

2012-01-01

One of the important ore-concentrated areas of carbonaceous-siliceous-pelitic rock type uranium deposits is the Southeast continental margin of Yangtze plate. Sedimentary-exogenously transformed type and sedimentary- hydrothermal superimposed transformed type uranium deposits are always distributed at or near the edge of down-faulted red ba sins. In this paper, the distributions of the deposits are analyzed with the relation to down-faulted red basins. The connective effect and ore-controlling mechanism are proposed of carbonaceous-siliceous-pelitic rock type uranium deposits with marginal fractures of red basins. (authors)

Stability of Large Parallel Tunnels Excavated in Weak Rocks: A Case Study

Science.gov (United States)

Ding, Xiuli; Weng, Yonghong; Zhang, Yuting; Xu, Tangjin; Wang, Tuanle; Rao, Zhiwen; Qi, Zufang

2017-09-01

Diversion tunnels are important structures for hydropower projects but are always placed in locations with less favorable geological conditions than those in which other structures are placed. Because diversion tunnels are usually large and closely spaced, the rock pillar between adjacent tunnels in weak rocks is affected on both sides, and conventional support measures may not be adequate to achieve the required stability. Thus, appropriate reinforcement support measures are needed, and the design philosophy regarding large parallel tunnels in weak rocks should be updated. This paper reports a recent case in which two large parallel diversion tunnels are excavated. The rock masses are thin- to ultra-thin-layered strata coated with phyllitic films, which significantly decrease the soundness and strength of the strata and weaken the rocks. The behaviors of the surrounding rock masses under original (and conventional) support measures are detailed in terms of rock mass deformation, anchor bolt stress, and the extent of the excavation disturbed zone (EDZ), as obtained from safety monitoring and field testing. In situ observed phenomena and their interpretation are also included. The sidewall deformations exhibit significant time-dependent characteristics, and large magnitudes are recorded. The stresses in the anchor bolts are small, but the extents of the EDZs are large. The stability condition under the original support measures is evaluated as poor. To enhance rock mass stability, attempts are made to reinforce support design and improve safety monitoring programs. The main feature of these attempts is the use of prestressed cables that run through the rock pillar between the parallel tunnels. The efficacy of reinforcement support measures is verified by further safety monitoring data and field test results. Numerical analysis is constantly performed during the construction process to provide a useful reference for decision making. The calculated deformations are in

Location-Related Differences in Weathering Behaviors and Populations of Culturable Rock-Weathering Bacteria Along a Hillside of a Rock Mountain.

Science.gov (United States)

Wang, Qi; Wang, Rongrong; He, Linyan; Sheng, Xiafang

2017-05-01

Bacteria play important roles in rock weathering, elemental cycling, and soil formation. However, little is known about the weathering potential and population of bacteria inhabiting surfaces of rocks. In this study, we isolated bacteria from the top, middle, and bottom rock samples along a hillside of a rock (trachyte) mountain as well as adjacent soils and characterized rock-weathering behaviors and populations of the bacteria. Per gram of rock or surface soil, 10 6 -10 7 colony forming units were obtained and total 192 bacteria were isolated. Laboratory rock dissolution experiments indicated that the proportions of the highly effective Fe (ranging from 67 to 92 %), Al (ranging from 40 to 48 %), and Cu (ranging from 54 to 81 %) solubilizers were significantly higher in the top rock and soil samples, while the proportion of the highly effective Si (56 %) solubilizers was significantly higher in the middle rock samples. Furthermore, 78, 96, and 6 % of bacteria from the top rocks, soils, and middle rocks, respectively, significantly acidified the culture medium (pH bacteria (79 %) from the rocks were different to those from the soils and most of them (species level) have not been previously reported. Furthermore, location-specific rock-weathering bacterial populations were found and Bacillus species were the most (66 %) frequently isolated rock-weathering bacteria in the rocks based on cultivation methods. Notably, the top rocks and soils had the highest and lowest diversity of rock-weathering bacterial populations, respectively. The results suggested location-related differences in element (Si, Al, Fe, and Cu) releasing effectiveness and communities of rock-weathering bacteria along the hillside of the rock mountain.

Humus soil as a critical driver of flora conversion on karst rock outcrops.

Science.gov (United States)

Zhu, Xiai; Shen, Youxin; He, Beibei; Zhao, Zhimeng

2017-10-03

Rock outcrop is an important habitat supporting plant communities in karst landscape. However, information on the restoration of higher biotic populations on outcrops is limited. Here, we investigated the diversity, biomass changes of higher vascular plants (VP) and humus soil (HS) on karst outcrops during a restoration process. We surveyed VP on rock outcrops and measured HS reserved by various rock microhabitats in a rock desertification ecosystem (RDE), an anthropogenic forest ecosystem (AFE), and a secondary forest ecosystem (SFE) in Shilin County, southwest China. HS metrics (e.g. quantity and nutrients content) and VP metrics (e.g. richness, diversity and biomass) were higher at AFE than at RDE, but lower than at SFE, suggesting that the restoration of soil subsystem vegetation increased HS properties and favored the succession of VP on rock outcrops. There was significantly positive correlation between VP metrics and HS amount, indicating that the succession of VP was strongly affected by availability and heterogeneity of HS in various rock microhabitats. Thus, floral succession of rock subsystem was slow owing to the limited resources on outcrops, although the vegetation was restored in soil subsystem.

ROCK1 and ROCK2 are Required for Non-Small Cell Lung Cancer Anchorage-Independent Growth and Invasion

OpenAIRE

Vigil, Dominico; Kim, Tai Young; Plachco, Ana; Garton, Andrew J.; Castaldo, Linda; Pachter, Jonathan A.; Dong, Hanqing; Chen, Xin; Tokar, Brianna; Campbell, Sharon L.; Der, Channing J.

2012-01-01

Evidence is emerging that the closely related ROCK1 and ROCK2 serine/threonine kinases support the invasive and metastatic growth of a spectrum of human cancer types. Therefore, inhibitors of ROCK are under preclinical development. However, a key step in their development involves the identification of genetic biomarkers that will predict ROCK inhibitor anti-tumor activity. One identified mechanism for ROCK activation in cancer involves the loss of function of the DLC1 tumor suppressor gene, ...

Floristic composition and diversity of three forest types at Caparu, Vaupus Biological Station

International Nuclear Information System (INIS)

Cano, Angela; Stevenson, Pablo R

2009-01-01

The Amazon forests are among the most diverse ecosystems in the planet. Although some countries of the Amazon Basin have a fairly complete record of their plants, in Colombia much effort is still needed to have a good idea of the plant diversity patterns and floristic composition. Three one-hectare vegetation-land plots (DBH? 10 cm) were established in Vaupes, Colombia, regarding three types of forest: Colina, Terraza (Terra Firme forests) and Igapo (periodically flooded). Plant diversity was estimated and floristic composition was described classifying the most important families and species. The highest diversity was found in Colina (Fisher's ? = 160.3), followed by Terraza (? = 78.4) and Igapo (? = 44.7). Fabaceae s.l. was the most important family of all plots, but in Terraza forest the importance of Arecaceae was similar to that of Fabaceae. Floristic composition was also remarkably different amongst the three forest types, especially Igapo, which was the most dissimilar. However, both Terra Firme forests showed strong floristic differences, which may be caused by differences in abiotic factors (i.e. soils). High plant diversity reported in this study agrees with the hypothesis that central and western Amazon forests are the most diverse of the Amazon Basin.

Regulation of ROCK Activity in Cancer

DEFF Research Database (Denmark)

Morgan-Fisher, Marie; Wewer, Ulla M; Yoneda, Atsuko

2013-01-01

, these findings demonstrate additional modes to regulate ROCK activity. This review describes the molecular mechanisms of ROCK activity regulation in cancer, with emphasis on ROCK isoform-specific regulation and interaction partners, and discusses the potential of ROCKs as therapeutic targets in cancer.......Cancer-associated changes in cellular behavior, such as modified cell-cell contact, increased migratory potential, and generation of cellular force, all require alteration of the cytoskeleton. Two homologous mammalian serine/threonine kinases, Rho-associated protein kinases (ROCK I and II), are key...... regulators of the actin cytoskeleton acting downstream of the small GTPase Rho. ROCK is associated with cancer progression, and ROCK protein expression is elevated in several types of cancer. ROCKs exist in a closed, inactive conformation under quiescent conditions, which is changed to an open, active...

The diversity of Porcine Reproductive and Respiratory Syndrome Virus Type 1 and 2 in Denmark

DEFF Research Database (Denmark)

Kvisgaard, Lise Kirstine; Hjulsager, Charlotte Kristiane; Kristensen, Charlotte Sonne

strains were sequenced. Denmark exports more than 50.000 living pigs each month. A portion of these pigs inevitably harbor PRRSV. Thus, the diversity of PRRSV in Denmark is of interest to other countries besides Denmark. The main objective of the present study was to close the gap in knowledge...... for both PRRSV genotypes has been widely used in Denmark and it is therefore highly relevant to monitor the diversity of currently circulating PRRSV strains. Only subtype 1 of the Type 1 PRRSV strains and vaccine-like Type 2 PRRSV strains were previously detected in Denmark, however, only few Danish PRRSV...... on the genetic diversity of currently circulating PRRSV stains in Danish pigs by sequencing ORF5 and ORF7 of approximately 41 Type 1 and 50 Type 2 strains isolated between 2003 and 2013. Furthermore, full genome analysis was performed on nine Type 1 and nine Type 2 selected strains. The preliminary assessment...

The Usability of Rock-Like Materials for Numerical Studies on Rocks

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

artificial simulations. The results obtained from these laboratory tests and modelling studies were compared with the other researcher's studies in respect to failure mechanism of different type of rocks. It can be concluded that there is similar failure mechanism between concrete and rock materials. Therefore, the results obtained from concrete samples that would be prepared at different porosity and pore sizes can be used in future studies in selection micro-mechanical and physical properties to constitute synthetic rock materials for understanding failure mechanism of rocks having complex inherent structures such as vuggy rocks or heavily jointed rock masses.

Original geochemical types and epigenetic alteration of rocks in prospecting target stratum for uranium deposit in the southeast of Songliao basin

International Nuclear Information System (INIS)

Lin Jinrong; Tian Hua; Dong Wenming; Xia Yuliang; Qi Daneng; Yao Shancong; Zheng Jiwei

2009-01-01

By comprehensive analysis on informations of regional geology and evaluating drillhole works of uranium resources in the southeast of Songliao basin, lithofacies-palaeogeography features, lithologies and sandbody characteristics of target layes in Quantou formation, Yaojia formation and Sifangtai formation have been basically found out. By research on geochemical environment of rocks in target layez, types of original geochemistry and epigenetic alteration have been identified and classified. The types of original geochemistry have been divided into types of original oxidation and original reduction, and the types of epigenetic alteration have been divided into types of reduction by oil-gas and coalbed gas and epigenetic oxidation. By comparative study on mineral and chemical characteristics of original geochemistry and epigenetic oxidation, identification marks for oil-gas and coalbed gas reduced epigenetic oxidation have been proposed. It is proposed that uranium was strongly pre-concentrated in original sandstone that bearing carboniferous matter, and reduction by oil-gas and coalbed gas made uranium superimpose and concentrate in alterated rocks. (authors)

Rotation of the accreting white dwarfs and diversity of type Ia supernovae

International Nuclear Information System (INIS)

Uenishi, Tatsuhiro; Nomoto, Kenichi; Hachisu, Izumi

2003-01-01

We consider rotation of progenitor white dwarfs for a possible source of the diversity of Type Ia supernovae (SNe Ia). Hydrostatic structure of rotating white dwarfs with different masses are calculated. Evolutionary sequences of white dwarfs are explored and the effect of 'supercritical' rotation in binary system is examined. Possible effects of rotation to cause diversity of SNe Ia are discussed

Christian rock concerts as a meeting between religion and popular culture

Directory of Open Access Journals (Sweden)

Andreas Häger

2003-01-01

Full Text Available Different forms of artistic expression play a vital role in religious practices of the most diverse traditions. One very important such expression is music. This paper deals with a contemporary form of religious music, Christian rock. Rock or popular music has been used within Christianity as a means for evangelization and worship since the end of the 1960s. The genre of "contemporary Christian music", or Christian rock, stands by definition with one foot in established institutional (in practicality often evangelical Christianity, and the other in the commercial rock musicindustry. The subject of this paper is to study how this intermediate position is manifested and negotiated in Christian rock concerts. Such a performance of Christian rock music is here assumed to be both a rock concert and a religious service. The paper will examine how this duality is expressed in practices at Christian rock concerts.

Remote Sensing of Rock Type in the Visible and Near-Infrared,

Science.gov (United States)

Visible and near-infrared spectra of minerals and rocks have been measured and evaluated in terms of remote sensing applications. The authors...difficult or impossible to use in a generalized remote sensing effort in which the composition of all rocks is to be mapped. Instead, this spectral

Radioactivities (dose rates) of rocks in Japan

International Nuclear Information System (INIS)

Matsuda, Hideharu; Minato, Susumu

1995-01-01

The radioactive distribution (radiation doses) of major rocks in Japan was monitored to clarify the factors influencing terrestrial gamma-ray absorbed dose rates. The rock samples were reduced to powder and analyzed by well-type NaI(Tl) scintillation detector and pulse height analyzer. Terrestrial gamma-ray dose rates were estimated in terms of gamma radiation dose rate 1 m above the ground. The radioactivity concentration was highest in acidic rock which contains much SiO 2 among igneous rock, followed by neutral rock, basic rock, and ultrabasic rock. The radioactive concentration was 30-40% lower in acidic and clastic rocks than those of the world average concentration. Higher radioactive concentration was observed in soils than the parent rocks of sedimentary rock and metamorphic rock. The gamma radiation dose rate was in proportion to the radioactive concentration of the rocks. To clarify the radioactive effect in the change course of rocks into soils, comparative measurement of outcrop and soil radioactive concentrations is important. (S.Y.)

Professional users handbook for rock bolting

Energy Technology Data Exchange (ETDEWEB)

Stillborg, B.

1986-01-01

The paper is a practical handbook which reviews the basic principles of rock bolting and sets out the design considerations used for most types of rockbolts in current use. It discusses the characteristics of these bolts and gives information on installation procedures and the observations and measurement of rockbolt performance. Rockbolting is considered under the following chapter headings: review of typical rockbolt systems; rockbolt installation; testing of rockbolts; design considerations; design of rock reinforcement; monitoring; cost of rock bolting; and Atlas Lopco auxillary equipment for rock bolting. 45 refs.

Rock-colonizing plants: abundance of the endemic cactus Mammillaria fraileana related to rock type in the southern Sonoran Desert

Science.gov (United States)

Blanca R. Lopez; Yoav Bashan; Macario Bacilio; Gustavo. De la Cruz-Aguero

2009-01-01

Establishment, colonization, and permanence of plants affect biogenic and physical processes leading to development of soil. Rockiness, temperature, and humidity are accepted explanations to the influence and the presence of rock-dwelling plants, but the relationship between mineral and chemical composition of rocks with plant abundance is unknown in some regions. This...

Anisotropy effect on strengths of metamorphic rocks

Directory of Open Access Journals (Sweden)

Ahmet Özbek

2018-02-01

Full Text Available This paper aims to study the effect of anisotropy on strengths of several metamorphic rocks of southern (Çine submassif of Menderes metamorphic massif in southwest Turkey. Four different metamorphic rocks including foliated phyllite, schist, gneiss and marble (calcschist were selected and examined. Discontinuity surveys were made along lines for each rock and evaluated with DIPS program. L-type Schmidt hammer was applied in the directions parallel and perpendicular to foliation during the field study. Several hand samples and rock blocks were collected during the field study for measurements of dry and saturated densities, dry and saturated unit weights and porosity, and for petrographic analysis and strength determination in laboratory. L- and N-type Schmidt hammers were applied in the directions perpendicular (anisotropy angle of 0° and parallel (anisotropy angle of 90° to the foliation on selected blocks of phyllite, schist, gneiss and marble (calcschist. The phyllite and schist have higher porosity and lower density values than the other rocks. However, coarse crystalline gneiss and marble (calcschist have higher rebound values and strengths, and they are classified as strong–very strong rocks. Generally, the rebound values in the direction perpendicular to the foliation are slightly higher than that in the direction parallel to foliation. Rebound values of N-type Schmidt hammer are higher than the L-type values except for phyllite. Sometimes, the rebound values of laboratory and field applications gave different results. This may result from variable local conditions such as minerals differentiation, discontinuities, water content, weathering degree and thickness of foliated structure.

Determining Clostridium difficile intra-taxa diversity by mining multilocus sequence typing databases.

Science.gov (United States)

Muñoz, Marina; Ríos-Chaparro, Dora Inés; Patarroyo, Manuel Alfonso; Ramírez, Juan David

2017-03-14

Multilocus sequence typing (MLST) is a highly discriminatory typing strategy; it is reproducible and scalable. There is a MLST scheme for Clostridium difficile (CD), a gram positive bacillus causing different pathologies of the gastrointestinal tract. This work was aimed at describing the frequency of sequence types (STs) and Clades (C) reported and evalute the intra-taxa diversity in the CD MLST database (CD-MLST-db) using an MLSA approach. Analysis of 1778 available isolates showed that clade 1 (C1) was the most frequent worldwide (57.7%), followed by C2 (29.1%). Regarding sequence types (STs), it was found that ST-1, belonging to C2, was the most frequent. The isolates analysed came from 17 countries, mostly from the United Kingdom (UK) (1541 STs, 87.0%). The diversity of the seven housekeeping genes in the MLST scheme was evaluated, and alleles from the profiles (STs), for identifying CD population structure. It was found that adk and atpA are conserved genes allowing a limited amount of clusters to be discriminated; however, different genes such as drx, glyA and particularly sodA showed high diversity indexes and grouped CD populations in many clusters, suggesting that these genes' contribution to CD typing should be revised. It was identified that CD STs reported to date have a mostly clonal population structure with foreseen events of recombination; however, one group of STs was not assigned to a clade being highly different containing at least nine well-supported clusters, suggesting a greater amount of clades for CD. This study shows the usefulness of CD-MLST-db as a tool for studying CD distribution and population structure, identifying the need for reviewing the usefulness of sodA as housekeeping gene within the MLST scheme and suggesting the existence of a greater amount of CD clades. The study also shows the plausible exchange of genetic material between STs, contributing towards intra-taxa genetic diversity.

Interactions of Various types between Rock and Alkali-Activated Blast Furnace Slag

Directory of Open Access Journals (Sweden)

Mec Pavel

2017-03-01

Full Text Available Alkali-activated binders (AAB are very intensively studied materials nowadays. Because of possible usage as secondary raw materials, they can be environmentally efficient. Intensive research is focused especially on binder matrix, composition and its structure. For industrial usage, it is necessary to work with some aggregate for the preparation of mortars and concretes. Due to different structures of alkali-activated binders, the interaction with the aggregate will be different in comparison to an ordinary Portland cement binder. This paper deals with the study of interactions between several types of rocks used as aggregate and alkali-activated blast furnace slag. The research was focused especially on mechanical properties of prepared mortars.

Experimental Rock-on-Rock Abrasive Wear Under Aqueous Conditions: its Role in Subglacial Abrasion

Science.gov (United States)

Rutter, E. H.; Lee, A. G.

2003-12-01

We have determined experimentally the rate of abrasive wear of rock on rock for a range of rock types as a function of normal stress and shear displacement. Unlike abrasive wear in fault zones, where wear products accumulate as a thickening gouge zone, in our experiments wear particles were removed by flowing water. The experiments are thus directly pertinent to one of the most important processes in subglacial erosion, and to some extent in river incision. Wear was produced between rotating discs machined from rock samples and measured from the progressive approach of the disc axes towards each other under various levels of normal load. Shear displacements of several km were produced. Optical and scanning electron microscopy were used to study the worn rock surfaces, and particle size distributions in wear products were characterized using a laser particle size analyzer. Rock types studied were sandstones of various porosities and cement characteristics, schists and a granite. In all cases abrasion rate decreased logarithmically with displacement by up to 2 orders of magnitude until a steady state was approached, but only after at least 1 km displacement. The more porous, less-well cemented rocks wore fastest. Amount of abrasion could be characterized quantitatively using an exponentially decaying plus a steady-state term. Wear rate increased non-linearly with normal contact stress, apparently to an asymptote defined by the unconfined compressive strength. Microstructural study showed that the well-cemented and/or lowest porosity rocks wore by progressive abrasion of grains without plucking, whereas whole grains were plucked out of weakly-cemented and/or more porous rocks. This difference in behavior was reflected in wear-product particle size distributions. Where whole-grain plucking was possible, wear products were dominated by particles of the original grain size rather than finer rock flour. Comparison of our results to glacier basal abrasive wear estimated

Sorption of cesium in intact rock

International Nuclear Information System (INIS)

Puukko, E.

2014-04-01

The mass distribution coefficient K d is used in performance assessment (PA) to describe sorption of a radionuclide on rock. The R d is determined using crushed rock which causes uncertainty in converting the R d values to K d values for intact rock. This work describes a method to determine the equilibrium of sorption on intact rock. The rock types of the planned Olkiluoto waste disposal site were T-series mica gneiss (T-MGN), T-series tonalite granodiorite granite gneiss (T-TGG), P-series tonalite granodiorite granite gneiss (P-TGG) and pegmatitic granite (PGR). These rocks contain different amount of biotite which is the main sorbing mineral. The sorption of cesium on intact rock slices was studied by applying an electrical field to speed up migration of cesium into the rock. Cesium is in the solution as a noncomplex cation Cs + and it is sorbed by ion exchange. The tracer used in the experiments was 134 Cs. The experimental sorption on the intact rock is compared with values calculated using the in house cation exchange sorption model (HYRL model) in PHREEQC program. The observed sorption on T-MGN and T-TGG rocks was close to the calculated values. Two PGR samples were from a depth of 70 m and three samples were from a depth of 150 m. Cesium sorbed more than predicted on the two 70 m PGR samples. The sorption of Cs on the three 150 m PGR samples was small which was consistent with the calculations. The pegmatitic granite PGR has the smallest content of biotite of the four rock types. In the case of P-TGG rock the observed values of sorption were only half of the calculated values. Two kind of slices were cut from P-TGG drill core. The slices were against and to the direction of the foliation of the biotite rims. The sorption of cesium on P-TGG rock was same in both cases. The results indicated that there was no effect of the directions of the electric field and the foliation of biotite in the P-TGG rock. (orig.)

Implicit fracture modelling in FLAC3D: Assessing the behaviour of fractured shales, carbonates and other fractured rock types

NARCIS (Netherlands)

Osinga, S.; Pizzocolo, F.; Veer, E.F. van der; Heege, J.H. ter

2016-01-01

Fractured rocks play an important role in many types of petroleum and geo-energy operations. From fractured limestone reservoirs to unconventionals, understanding the geomechanical behaviour and the dynamically coupled (dual) permeability system is paramount for optimal development of these systems.

Regulation of ROCK Activity in Cancer

Science.gov (United States)

Morgan-Fisher, Marie; Wewer, Ulla M.

2013-01-01

Cancer-associated changes in cellular behavior, such as modified cell-cell contact, increased migratory potential, and generation of cellular force, all require alteration of the cytoskeleton. Two homologous mammalian serine/threonine kinases, Rho-associated protein kinases (ROCK I and II), are key regulators of the actin cytoskeleton acting downstream of the small GTPase Rho. ROCK is associated with cancer progression, and ROCK protein expression is elevated in several types of cancer. ROCKs exist in a closed, inactive conformation under quiescent conditions, which is changed to an open, active conformation by the direct binding of guanosine triphosphate (GTP)–loaded Rho. In recent years, a number of ROCK isoform-specific binding partners have been found to modulate the kinase activity through direct interactions with the catalytic domain or via altered cellular localization of the kinases. Thus, these findings demonstrate additional modes to regulate ROCK activity. This review describes the molecular mechanisms of ROCK activity regulation in cancer, with emphasis on ROCK isoform-specific regulation and interaction partners, and discusses the potential of ROCKs as therapeutic targets in cancer. PMID:23204112

Permanganate diffusion and reaction in sedimentary rocks.

Science.gov (United States)

Huang, Qiuyuan; Dong, Hailiang; Towne, Rachael M; Fischer, Timothy B; Schaefer, Charles E

2014-04-01

In situ chemical oxidation using permanganate has frequently been used to treat chlorinated solvents in fractured bedrock aquifers. However, in systems where matrix back-diffusion is an important process, the ability of the oxidant to migrate and treat target contaminants within the rock matrix will likely determine the overall effectiveness of this remedial approach. In this study, a series of diffusion experiments were performed to measure the permanganate diffusion and reaction in four different types of sedimentary rocks (dark gray mudstone, light gray mudstone, red sandstone, and tan sandstone). Results showed that, within the experimental time frame (~2 months), oxidant migration into the rock was limited to distances less than 500 μm. The observed diffusivities for permanganate into the rock matrices ranged from 5.3 × 10(-13) to 1.3 × 10(-11) cm(2)/s. These values were reasonably predicted by accounting for both the rock oxidant demand and the effective diffusivity of the rock. Various Mn minerals formed as surface coatings from reduction of permanganate coupled with oxidation of total organic carbon (TOC), and the nature of the formed Mn minerals was dependent upon the rock type. Post-treatment tracer testing showed that these Mn mineral coatings had a negligible impact on diffusion through the rock. Overall, our results showed that the extent of permanganate diffusion and reaction depended on rock properties, including porosity, mineralogy, and organic carbon. These results have important implications for our understanding of long-term organic contaminant remediation in sedimentary rocks using permanganate. Copyright © 2014 Elsevier B.V. All rights reserved.

The mineralogy and petrology of I-type cosmic spherules: Implications for their sources, origins and identification in sedimentary rocks

Science.gov (United States)

Genge, Matthew J.; Davies, Bridie; Suttle, Martin D.; van Ginneken, Matthias; Tomkins, Andrew G.

2017-12-01

I-type cosmic spherules are micrometeorites that formed by melting during atmospheric entry and consist mainly of iron oxides and FeNi metal. I-types are important because they can readily be recovered from sedimentary rocks allowing study of solar system events over geological time. We report the results of a study of the mineralogy and petrology of 88 I-type cosmic spherules recovered from Antarctica in order to evaluate how they formed and evolved during atmospheric entry, to constrain the nature of their precursors and to establish rigorous criteria by which they may be conclusively identified within sediments and sedimentary rocks. Two textural types of I-type cosmic spherule are recognised: (1) metal bead-bearing (MET) spherules dominated by Ni-poor (100 and suggest that metal from H-group ordinary, CM, CR and iron meteorites may form the majority of particles. Oxidation during entry heating increases in the series MET 80 wt% Ni comprising a particle mass fraction of exchange of Ni between wüstite and metal, and magnetite and wüstite are suggested as proxies for the rate of oxidation and cooling rate respectively. Variations in magnetite and wüstite crystal sizes are also suggested to relate to cooling rate allowing relative entry angle of particles to be evaluated. The formation of secondary metal in the form of sub-micron Ni-rich or Pt-group nuggets and as symplectite with magnetite was also identified and suggested to occur largely due to the exsolution of metallic alloys during decomposition of non-stoichiometric wüstite. Weathering is restricted to replacement of metal by iron hydroxides. The following criteria are recommended for the conclusive identification of I-type spherules within sediments and sedimentary rocks: (i) spherical particle morphologies, (ii) dendritic crystal morphologies, (iii) the presence of wüstite and magnetite, (iv) Ni-bearing wüstite and magnetite, and (v) the presence of relict FeNi metal.

Human immunodeficiency virus type-1 (HIV-1) genetic diversity and ...

African Journals Online (AJOL)

The presence of human immunodeficiency virus (HIV) type-1 diversity has an impact on vaccine efficacy and drug resistance. It is important to know the circulating genetic variants and associated drug-resistance mutations in the context of scale up of antiretroviral therapy (ART) in Nigeria. The objective of this study was to ...

Structural Analysis: Folds Classification of metasedimentary rock in the Peninsular Malaysia

Science.gov (United States)

Shamsuddin, A.

2017-10-01

Understanding shear zone characteristics of deformation are a crucial part in the oil and gas industry as it might increase the knowledge of the fracture characteristics and lead to the prediction of the location of fracture zones or fracture swarms. This zone might give high influence on reservoir performance. There are four general types of shear zones which are brittle, ductile, semibrittle and brittle-ductile transition zones. The objective of this study is to study and observe the structural geometry of the shear zones and its implication as there is a lack of understanding, especially in the subsurface area because of the limitation of seismic resolution. A field study was conducted on the metasedimentary rocks (shear zone) which are exposed along the coastal part of the Peninsular Malaysia as this type of rock resembles the types of rock in the subsurface. The analysis in this area shows three main types of rock which are non-foliated metaquartzite and foliated rock which can be divided into slate and phyllite. Two different fold classification can be determined in this study. Layer 1 with phyllite as the main type of rock can be classified in class 1C and layer 2 with slate as the main type of rock can be classified in class 1A. This study will benefit in predicting the characteristics of the fracture and fracture zones.

Sorptivity of rocks and soils of the van Genuchten-Mualem type

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, R.W.; Bodvarsson, G.S. [Lawrence Berkeley Lab., CA (United States)

1991-06-01

One hydrological process that will have great relevance to the performance of the proposed underground radioactive waste repository at Yucca Mountain, Nevada, is that of the absorption of water from a water-filled fracture into the adjacent unsaturated rock formation. The rate at which water is imbibed by a rock depends on the hydrological properties of the rock and on the initial saturation (or initial capillary suction) of the formation. The hydrological properties that affect imbibition are the relative permeability function and the capillary pressure function. These functions are often collectively referred to as the `characteristic functions` of the porous medium. For one-dimensional absorption, it can be shown that, regardless of the details of the characteristic functions, the total amount of water imbibed by the formation, per unit surface area, will be proportional to the square root of the elapsed time. Hence the ability of a rock or soil to imbibe water can be quantified by a parameter known as the sorptivity S, which is defined such that the cumulative volumetric liquid influx per unit area is given by Q = S{radical}t. The paper discusses the simplification of these characteristic functions of porous medium.

Large-Scale True Triaxial Apparatus for Geophysical Studies in Fractured Rock

KAUST Repository

Garcia, A. V.

2018-05-12

The study of fractured rock masses in the laboratory remains challenging because of the large specimen sizes and bulky loading systems that are required. This article presents the design, structural analysis, and operation of a compact and self-reacting true triaxial device for fractured rock. The frame subjects a 50 cm by 50 cm by 50 cm fractured rock specimen to a maximum stress of 3 MPa along three independent axes. Concurrent measurements include long-wavelength P-wave propagation, passive acoustic emission monitoring, deformations, and thermal measurements. The device can accommodate diverse research, from rock mass properties and geophysical fractured rock characterizations, to coupled hydro-chemo-thermo-mechanical processes, drilling, and grouting. Preliminary wave propagation data gathered under isotropic and anisotropic stress conditions for an assembly of 4,000 rock blocks demonstrate the system’s versatility and provide unprecedented information related to long-wavelength propagation in fractured rock under various stress anisotropies.

Large-Scale True Triaxial Apparatus for Geophysical Studies in Fractured Rock

KAUST Repository

Garcia, A. V.; Rached, R. M.; Santamarina, Carlos

2018-01-01

The study of fractured rock masses in the laboratory remains challenging because of the large specimen sizes and bulky loading systems that are required. This article presents the design, structural analysis, and operation of a compact and self-reacting true triaxial device for fractured rock. The frame subjects a 50 cm by 50 cm by 50 cm fractured rock specimen to a maximum stress of 3 MPa along three independent axes. Concurrent measurements include long-wavelength P-wave propagation, passive acoustic emission monitoring, deformations, and thermal measurements. The device can accommodate diverse research, from rock mass properties and geophysical fractured rock characterizations, to coupled hydro-chemo-thermo-mechanical processes, drilling, and grouting. Preliminary wave propagation data gathered under isotropic and anisotropic stress conditions for an assembly of 4,000 rock blocks demonstrate the system’s versatility and provide unprecedented information related to long-wavelength propagation in fractured rock under various stress anisotropies.

Rocks and geology in the San Francisco Bay region

Science.gov (United States)

Stoffer, Philip W.

2002-01-01

The landscape of the San Francisco Bay region is host to a greater variety of rocks than most other regions in the United States. This introductory guide provides illustrated descriptions of 46 common and important varieties of igneous, sedimentary, and metamorphic rock found in the region. Rock types are described in context of their identification qualities, how they form, and where they occur in the region. The guide also provides discussion about of regional geology, plate tectonics, the rock cycle, the significance of the selected rock types in relation to both earth history and the impact of mineral resources on the development in the region. Maps and text also provide information where rocks, fossils, and geologic features can be visited on public lands or in association with public displays in regional museums, park visitor centers, and other public facilities.

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 18. Facility construction feasibility and costs by rock type

International Nuclear Information System (INIS)

1978-04-01

The results of a study that compared the general engineering feasibility and unit costs associated with sinking shafts and mining storage rooms in the four rock types (salt, granite, shale, basalt) are presented in this volume. The report includes a discussion of the general effects of rock characteristics on shaft and mine design, the application of these design considerations to the specific designs developed for the Draft GEIS, shaft and mine construction techniques, and the unit cost comparison. The repository designs upon which this comparison was based are presented in other volumes of this series

Exploring How Weathering Related Stresses and Subcritical Crack Growth May Influence the Size of Sediment Produced From Different Rock Types.

Science.gov (United States)

Eppes, M. C.; Hallet, B.; Hancock, G. S.; Mackenzie-Helnwein, P.; Keanini, R.

2016-12-01

outcrops of granite, sandstone, and quartzite found in Shenandoah National Park, Virginia. Preliminary results reveal that many observed cracking characteristics are consistent with our hypotheses linking subcritical crack growth, weathering stresses and the production of different sized sediment from different rock types.

Rock Slope Design Criteria : Executive Summary Report

Science.gov (United States)

2010-06-01

Based on the stratigraphy and the type of slope stability problems, the flat lying, Paleozoic age, sedimentary rocks of Ohio were divided into three design units: 1) competent rock design unit consisting of sandstones, limestones, and siltstones that...

Thermally induced rock stress increment and rock reinforcement response

International Nuclear Information System (INIS)

Hakala, M.; Stroem, J.; Nujiten, G.; Uotinen, L.; Siren, T.; Suikkanen, J.

2014-07-01

deformation zones is included. The main conclusion is that, despite deep reaching damage potential, in all the load cases studied the currently designed and used reinforcement types and configurations (rock bolts, shotcrete) are capable of handling the dead weight of the damaged rock should this occur, with damage occurring on the shotcrete liner. The long term safety and stability of the repository during its lifetime can be guaranteed by perceiving the reinforcement strategy in two stages. Firstly, by installing the rock reinforcement to sustain the initial stresses and short term increases from the start of deposition with a monitoring programme in place. Secondly, by installing additional reinforcement, if found necessary through monitoring and observation of the underground facilities. In this way, the effect of any time dependent rock stress increase affecting the reinforcement structures can be observed, in addition to creep based damage, thus providing a better level of safety than a single stage design. (orig.)

Thermally induced rock stress increment and rock reinforcement response

Energy Technology Data Exchange (ETDEWEB)

Hakala, M. [KMS Hakala Oy, Nokia (Finland); Stroem, J.; Nujiten, G.; Uotinen, L. [Rockplan, Helsinki (Finland); Siren, T.; Suikkanen, J.

2014-07-15

brittle deformation zones is included. The main conclusion is that, despite deep reaching damage potential, in all the load cases studied the currently designed and used reinforcement types and configurations (rock bolts, shotcrete) are capable of handling the dead weight of the damaged rock should this occur, with damage occurring on the shotcrete liner. The long term safety and stability of the repository during its lifetime can be guaranteed by perceiving the reinforcement strategy in two stages. Firstly, by installing the rock reinforcement to sustain the initial stresses and short term increases from the start of deposition with a monitoring programme in place. Secondly, by installing additional reinforcement, if found necessary through monitoring and observation of the underground facilities. In this way, the effect of any time dependent rock stress increase affecting the reinforcement structures can be observed, in addition to creep based damage, thus providing a better level of safety than a single stage design. (orig.)

Comparison of laboratory, in situ, and rock mass measurements of the hydraulic conductivity of metamorphic rock at the Savannah River Plant near Aiken, South Carolina

International Nuclear Information System (INIS)

Marine, I.W.

1980-01-01

In situ testing of exploratory wells in metamorphic rock indicates that two types of fracturing occur in the rock mass. Rock containing small openings that permit only extremely slow movement of water is termed virtually impermeable rock. Rock containing openings of sufficient size to permit transmission of water at a significantly faster rate is termed hydraulically transmissive rock. Laboratory methods are unsuitable for measuring hydraulic conductivity in hydraulically transmissive rock; however, for the virtually impermeable rock, values comparable to the in situ tests are obtained. The hydraulic conductivity of the rock mass over a large region is calculated by using the hydraulic gradient, porosity, and regional velocity. This velocity is determined by dividing the inferred travel distance by the age of water which is determined by the helium content of the water. This rock mass hydraulic conductivity value is between the values measured for the two types of fractures, but is closer to the measured value for the virtually impermeable rock. This relationship is attributed to the control of the regional flow rate by the virtually impermeable rock where the discrete fractures do not form a continuous open connection through the entire rock mass. Thus, laboratory methods of measuring permeability in metamorphic rock are of value if they are properly applied

Microbial mat ecosystems: Structure types, functional diversity, and biotechnological application

Directory of Open Access Journals (Sweden)

Cristina M. Prieto-Barajas

2018-01-01

Full Text Available Microbial mats are horizontally stratified microbial communities, exhibiting a structure defined by physiochemical gradients, which models microbial diversity, physiological activities, and their dynamics as a whole system. These ecosystems are commonly associated with aquatic habitats, including hot springs, hypersaline ponds, and intertidal coastal zones and oligotrophic environments, all of them harbour phototrophic mats and other environments such as acidic hot springs or acid mine drainage harbour non-photosynthetic mats. This review analyses the complex structure, diversity, and interactions between the microorganisms that form the framework of different types of microbial mats located around the globe. Furthermore, the many tools that allow studying microbial mats in depth and their potential biotechnological applications are discussed.

Magnetic mineralogy and rock magnetic properties of silicate and carbonatite rocks from Oldoinyo Lengai volcano (Tanzania)

Science.gov (United States)

Mattsson, H. B.; Balashova, A.; Almqvist, B. S. G.; Bosshard-Stadlin, S. A.; Weidendorfer, D.

2018-06-01

Oldoinyo Lengai, a stratovolcano in northern Tanzania, is most famous for being the only currently active carbonatite volcano on Earth. The bulk of the volcanic edifice is dominated by eruptive products produced by silica-undersaturated, peralkaline, silicate magmas (effusive, explosive and/or as cumulates at depth). The recent (2007-2008) explosive eruption produced the first ever recorded pyroclastic flows at this volcano and the accidental lithics incorporated into the pyroclastic flows represent a broad variety of different rock types, comprising both extrusive and intrusive varieties, in addition to various types of cumulates. This mix of different accidental lithics provides a unique insight into the inner workings of the world's only active carbonatite volcano. Here, we focus on the magnetic mineralogy and the rock magnetic properties of a wide selection of samples spanning the spectrum of Oldoinyo Lengai rock types compositionally, as well from a textural point of view. Here we show that the magnetic properties of most extrusive silicate rocks are dominated by magnetite-ulvöspinel solid solutions, and that pyrrhotite plays a larger role in the magnetic properties of the intrusive silicate rocks. The natrocarbonatitic lavas, for which the volcano is best known for, show distinctly different magnetic properties in comparison with the silicate rocks. This discrepancy may be explained by abundant alabandite crystals/blebs in the groundmass of the natrocarbonatitic lavas. A detailed combination of petrological/mineralogical studies with geophysical investigations is an absolute necessity in order to understand, and to better constrain, the overall architecture and inner workings of the subvolcanic plumbing system. The results presented here may also have implications for the quest in order to explain the genesis of the uniquely natrocarbonatitic magmas characteristic of Oldoinyo Lengai.

Geohydromechanical Processes in the Excavation Damaged Zone in Crystalline Rock, Rock Salt, and Indurated and Plastic Clays

International Nuclear Information System (INIS)

Tsang, Chin-Fu; Bernier, Frederic; Davies, Christophe

2004-01-01

The creation of an excavation disturbed zone or excavation damaged zone is expected around all man-made openings in geologic formations. Macro- and micro-fracturing, and in general a redistribution of in situ stresses and rearrangement of rock structures, will occur in this zone, resulting in drastic changes of permeability to flow, mainly through the fractures and cracks induced by excavation. Such an EDZ may have significant implications for the operation and long-term performance of an underground nuclear waste repository. Various issues of concern need to be evaluated, such as processes creating fractures in the excavation damaged zone, the degree of permeability increase, and the potential for sealing or healing (with permeability reduction) in the zone. In recent years, efforts along these lines have been made for a potential repository in four rock types-crystalline rock, salt, indurated clay, and plastic clay-and these efforts have involved field, laboratory, and theoretical studies. The present work involves a synthesis of the ideas and issues that emerged from presentations and discussions on EDZ in these four rock types at a CLUSTER Conference and Workshop held in Luxembourg in November, 2003. First, definitions of excavation disturbed and excavation damaged zones are proposed. Then, an approach is suggested for the synthesis and intercomparison of geohydromechanical processes in the EDZ for the four rock types (crystalline rock, salt, indurated clay, and plastic clay). Comparison tables of relevant processes, associated factors, and modeling and testing techniques are developed. A discussion of the general state-of-the-art and outstanding issues are also presented. A substantial bibliography of relevant papers on the subject is supplied at the end of the paper

Shallow magma diversions during explosive diatreme-forming eruptions.

Science.gov (United States)

Le Corvec, Nicolas; Muirhead, James D; White, James D L

2018-04-13

The diversion of magma is an important mechanism that may lead to the relocation of a volcanic vent. Magma diversion is known to occur during explosive volcanic eruptions generating subterranean excavation and remobilization of country and volcanic rocks. However, feedbacks between explosive crater formation and intrusion processes have not been considered previously, despite their importance for understanding evolving hazards during volcanic eruptions. Here, we apply numerical modeling to test the impacts of excavation and subsequent infilling of diatreme structures on stress states and intrusion geometries during the formation of maar-diatreme complexes. Explosive excavation and infilling of diatremes affects local stress states which inhibits magma ascent and drives lateral diversion at various depths, which are expected to promote intra-diatreme explosions, host rock mixing, and vent migration. Our models demonstrate novel mechanisms explaining the generation of saucer-shaped sills, linked with magma diversion and enhanced intra-diatreme explosive fragmentation during maar-diatreme volcanism. Similar mechanisms will occur at other volcanic vents producing crater-forming eruptions.

Fault rocks and uranium mineralization

International Nuclear Information System (INIS)

Tong Hangshou.

1991-01-01

The types of fault rocks, microstructural characteristics of fault tectonite and their relationship with uranium mineralization in the uranium-productive granite area are discussed. According to the synthetic analysis on nature of stress, extent of crack and microstructural characteristics of fault rocks, they can be classified into five groups and sixteen subgroups. The author especially emphasizes the control of cataclasite group and fault breccia group over uranium mineralization in the uranium-productive granite area. It is considered that more effective study should be made on the macrostructure and microstructure of fault rocks. It is of an important practical significance in uranium exploration

Establishment of tunnel-boring machine disk cutter rock-breaking model from energy perspective

Directory of Open Access Journals (Sweden)

Liwei Song

2015-12-01

Full Text Available As the most important cutting tools during tunnel-boring machine tunneling construction process, V-type disk cutter’s rock-breaking mechanism has been researched by many scholars all over the world. Adopting finite element method, this article focused on the interaction between V-type disk cutters and the intact rock to carry out microscopic parameter analysis methods: first, the stress model of rock breaking was established through V-type disk cutter motion trajectory analysis; second, based on the incremental theorem of the elastic–plastic theory, the strain model of the relative changes of rock displacement during breaking process was created. According to the principle of admissible work by energy method of the elastic–plastic theory to analyze energy transfer rules in the process of breaking rock, rock-breaking force of the V-type disk cutter could be regarded as the external force in the rock system. Finally, by taking the rock system as the reference object, the total potential energy equivalent model of rock system was derived to obtain the forces of the three directions acting on V-type disk cutter during the rock-breaking process. This derived model, which has been proved to be effective and scientific through comparisons with some original force models and by comparative analysis with experimental data, also initiates a new research strategy taking the view of the micro elastic–plastic theory to study the rock-breaking mechanism.

Effect of type of explosives and physical-mechanical properties of explosive rock on formation of toxic gases in atmosphere of shafts

Science.gov (United States)

Mindeli, E. O.; Khudyakov, M. Y.

1981-01-01

The quality of toxic gases formed during explosive work in underground shafts depends upon the type of explosives and the conditions of explosion. Several types of explosives and rocks were examined. All remaining conditions were maintained the same (sandy-argillaceous stemming, electrical method of explosions, diameter of blast holes, and the direct triggering of charges).

The Usability of Noise Level from Rock Cutting for the Prediction of Physico-Mechanical Properties of Rocks

Science.gov (United States)

Delibalta, M. S.; Kahraman, S.; Comakli, R.

2015-11-01

Because the indirect tests are easier and cheaper than the direct tests, the prediction of rock properties from the indirect testing methods is important especially for the preliminary investigations. In this study, the predictability of the physico-mechanical rock properties from the noise level measured during cutting rock with diamond saw was investigated. Noise measurement test, uniaxial compressive strength (UCS) test, Brazilian tensile strength (BTS) test, point load strength (Is) test, density test, and porosity test were carried out on 54 different rock types in the laboratory. The results were statistically analyzed to derive estimation equations. Strong correlations between the noise level and the mechanical rock properties were found. The relations follow power functions. Increasing rock strength increases the noise level. Density and porosity also correlated strongly with the noise level. The relations follow linear functions. Increasing density increases the noise level while increasing porosity decreases the noise level. The developed equations are valid for the rocks with a compressive strength below 150 MPa. Concluding remark is that the physico-mechanical rock properties can reliably be estimated from the noise level measured during cutting the rock with diamond saw.

Geotechnical properties of rock

Energy Technology Data Exchange (ETDEWEB)

Jackson, R.; Gorski, B.; Gyenge, M.

1995-12-31

The manual is a compilation of the geotechnical properties of many types of rock that are typical of Canadian mining environments. Included are values for density, porosity, compressive and shear wave velocity, uniaxial compressive strength, Young`s modulus, and Poisson`s ratio. The data base contains material constants that were determined using the Hoek and Brown failure criteria for both before and after failure conditions. 76 data sheets of rock properties in Canadian mines are included. 7 refs., 85 figs., 3 tabs.

Synthetic Rock Analogue for Permeability Studies of Rock Salt with Mudstone

Directory of Open Access Journals (Sweden)

Hongwu Yin

2017-09-01

Full Text Available Knowledge about the permeability of surrounding rock (salt rock and mudstone interlayer is an important topic, which acts as a key parameter to characterize the tightness of gas storage. The goal of experiments that test the permeability of gas storage facilities in rock salt is to develop a synthetic analogue to use as a permeability model. To address the permeability of a mudstone/salt layered and mixed rock mass in Jintan, Jiangsu Province, synthetic mixed and layered specimens using the mudstone and the salt were fabricated for permeability testing. Because of the gas “slippage effect”, test results are corrected by the Klinkenberg method, and the permeability of specimens is obtained by regression fitting. The results show that the permeability of synthetic pure rock salt is 6.9 × 10−20 m2, and its porosity is 3.8%. The permeability of synthetic mudstone rock is 2.97 × 10−18 m2, with a porosity 17.8%. These results are close to those obtained from intact natural specimens. We also find that with the same mudstone content, the permeability of mixed specimens is about 40% higher than for the layered specimens, and with an increase in the mudstone content, the Klinkenberg permeability increases for both types of specimens. The permeability and mudstone content have a strong exponential relationship. When the mudstone content is below 40%, the permeability increases only slightly with mudstone content, whereas above this threshold, the permeability increases rapidly with mudstone content. The results of the study are of use in the assessment of the tightness of natural gas storage facilities in mudstone-rich rock salt formations in China.

Conceptual and safety-related questions in the final storage of radioactive waste - a comparison of various types of host rock

International Nuclear Information System (INIS)

Kleemann, U.

2005-01-01

The German Federal Office for Radiation Protection (BfS) in early November published the synthesis report (BfS 2005) about the conceptual and safety-related specific questions associated with the final storage of radioactive waste. In addition to a condensed version of twelve individual projects, the report contains a description of the results of the peer review and the workshops carried out, in particular an evaluation comparing different types of host rock in Germany. The whole project constitutes a comprehensive documentation of the current state of the art. Findings are expressed at a general level referring neither to the suitability of any specific repository site nor to that of salts as a repository formation, but covering all potential repository formations in deep geologic strata in Germany. The limits to and possibilities of, generic comparisons of various types of host rock are shown. It si seen that, in principle, none of the host rock varieties in Germany would be preferable to others. Numerous problems can be solved only for specific sites, thus requiring site comparisons. While some questions indicate a need for regulatory treatment, the need for basic research is considered to be low. The contribution presents the main findings made in each of the specific projects and the evaluations by the Office. (orig.)

Extrapolation of bulk rock elastic moduli of different rock types to high pressure conditions and comparison with texture-derived elastic moduli

Science.gov (United States)

Ullemeyer, Klaus; Lokajíček, Tomás; Vasin, Roman N.; Keppler, Ruth; Behrmann, Jan H.

2018-02-01

In this study elastic moduli of three different rock types of simple (calcite marble) and more complex (amphibolite, micaschist) mineralogical compositions were determined by modeling of elastic moduli using texture (crystallographic preferred orientation; CPO) data, experimental investigation and extrapolation. 3D models were calculated using single crystal elastic moduli, and CPO measured using time-of-flight neutron diffraction at the SKAT diffractometer in Dubna (Russia) and subsequently analyzed using Rietveld Texture Analysis. To define extrinsic factors influencing elastic behaviour, P-wave and S-wave velocity anisotropies were experimentally determined at 200, 400 and 600 MPa confining pressure. Functions describing variations of the elastic moduli with confining pressure were then used to predict elastic properties at 1000 MPa, revealing anisotropies in a supposedly crack-free medium. In the calcite marble elastic anisotropy is dominated by the CPO. Velocities continuously increase, while anisotropies decrease from measured, over extrapolated to CPO derived data. Differences in velocity patterns with sample orientation suggest that the foliation forms an important mechanical anisotropy. The amphibolite sample shows similar magnitudes of extrapolated and CPO derived velocities, however the pattern of CPO derived velocity is closer to that measured at 200 MPa. Anisotropy decreases from the extrapolated to the CPO derived data. In the micaschist, velocities are higher and anisotropies are lower in the extrapolated data, in comparison to the data from measurements at lower pressures. Generally our results show that predictions for the elastic behavior of rocks at great depths are possible based on experimental data and those computed from CPO. The elastic properties of the lower crust can, thus, be characterized with an improved degree of confidence using extrapolations. Anisotropically distributed spherical micro-pores are likely to be preserved, affecting

Mechanical properties of granitic rocks from Gideaa, Sweden

International Nuclear Information System (INIS)

Ljunggren, C.; Stephansson, O.; Alm, O.; Hakami, H.; Mattila, U.

1985-10-01

The elastic and mechanical properties were determined for two rock types from the Gideaa study area. Gideaa is located approximately 30 km north-east of Oernskoeldsvik, Northern Sweden. The rock types that were tested were migmatitic gneiss and migmatitic granite. The following tests were conducted: - sound velocity measurements; - uniaxial compression tests with acoustic emission recording; - brazilian disc tests; - triaxial tests; - three point bending tests. All together, 12 rock samples were tested with each test method. Six samples of these were migmatic gneiss and six samples were migmatitic granite. The result shows that the migmatitic gneiss has varying strength properties with low compressive strength in comparison with its high tensile strength. The migmatitic granite, on the other hand, is found to have parameter values similar to other granitic rocks. With 15 refs. (Author)

Theory and technology of rock excavation for civil engineering

CERN Document Server

Zou, Dingxiang

2017-01-01

This book summarizes the technical advances in recent decades and the various theories on rock excavation raised by scholars from different countries, including China and Russia. It not only focuses on rock blasting but also illustrates a number of non-blasting methods, such as mechanical excavation in detail. The book consists of 3 parts: Basic Knowledge, Surface Excavation and Underground Excavation. It presents a variety of technical methods and data from diverse sources in the book, making it a valuable theoretical and practical reference resource for engineers, researchers and postgraduates alike.

Neutron pole figures compared with magnetic preferred orientations of different rock types

International Nuclear Information System (INIS)

Hansen, Anke; Chadima, Martin; Cifelli, Francesca; Brokmeier, H.-G.Heinz-Guenter; Siemes, Heinrich

2004-01-01

Neutron diffraction is an excellent tool for pole figure measurement of rock samples. Due to high penetration depth of neutrons for most materials neutron diffraction represents an efficient tool to measure complete pole figures with reliable grain statistics even in coarse grained or inequi-granular materials. In the field of structural geology, the measurement of anisotropy of magnetic susceptibility is a standard technique to reveal the tectonic history of deformed rocks. The application of both techniques on still ongoing studies of Precambrian, Carboniferous and Quaternary rocks which are characterised by fundamental different tectonic evolutions and mineralogical compositions shows the wide field of relevance and importance of these methods in understanding tectonic processes in detail

Smart Rocking Armour Units

OpenAIRE

Hofland, B.; Arefin, Syed Shamsil; van der Lem, Cock; van gent, Marcel

2018-01-01

This paper describes a method to measure the rocking motion of lab-scale armour units. Sensors as found in mobile phones are used. These sensors, data-storage and battery are all embedded in the model units, such that they can be applied without wires attached to them. The technique is applied to double-layer units in order to compare the results to the existing knowledge for this type of armour layers. In contrast to previous research, the gyroscope reading is used to determine the (rocking)...

Rock Physical Interpretation of the Relationship between Dynamic and Static Young's Moduli of Sedimentary Rocks

Science.gov (United States)

Takahashi, T.

2017-12-01

The static Young's modulus (deformability) of a rock is indispensable for designing and constructing tunnels, dams and underground caverns in civil engineering. Static Young's modulus which is an elastic modulus at large strain level is usually obtained with the laboratory tests of rock cores sampled in boreholes drilled in a rock mass. A deformability model of the entire rock mass is then built by extrapolating the measurements based on a rock mass classification obtained in geological site characterization. However, model-building using data obtained from a limited number of boreholes in the rock mass, especially a complex rock mass, may cause problems in the accuracy and reliability of the model. On the other hand, dynamic Young's modulus which is the modulus at small strain level can be obtained from seismic velocity. If dynamic Young's modulus can be rationally converted to static one, a seismic velocity model by the seismic method can be effectively used to build a deformability model of the rock mass. In this study, we have, therefore, developed a rock physics model (Mavko et al., 2009) to estimate static Young's modulus from dynamic one for sedimentary rocks. The rock physics model has been generally applied to seismic properties at small strain level. In the proposed model, however, the sandy shale model, one of rock physics models, is extended for modeling the static Young's modulus at large strain level by incorporating the mixture of frictional and frictionless grain contacts into the Hertz-Mindlin model. The proposed model is verified through its application to the dynamic Young's moduli derived from well log velocities and static Young's moduli measured in the tri-axial compression tests of rock cores sampled in the same borehole as the logs were acquired. This application proves that the proposed rock physics model can be possibly used to estimate static Young's modulus (deformability) which is required in many types of civil engineering applications

Geochronology, geochemistry, and petrogenesis of late Permian to early Triassic mafic rocks from Darongshan, South China: Implications for ultrahigh-temperature metamorphism and S-type granite generation

Science.gov (United States)

Xu, Wang-Chun; Luo, Bi-Ji; Xu, Ya-Jun; Wang, Lei; Chen, Qi

2018-05-01

The role of the mantle in generating ultrahigh-temperature metamorphism and peraluminous S-type granites, and the extent of crust-mantle interaction are topics fundamental to our understanding of the Earth's evolution. In this study we present geochronological, geochemical, and Sr-Nd-Hf isotopic data for dolerites and mafic volcanic rocks from the Darongshan granite complex belt in western Cathaysia, South China. LA-ICP-MS U-Pb zircon analyses yielded magma crystallization ages of ca. 250-248 Ma for the dolerites, which are coeval with eruption of the mafic volcanic rocks, ultrahigh-temperature metamorphism, and emplacement of S-type granites in the Darongshan granite complex belt. The mafic volcanic rocks are high-K calc-alkaline or shoshonitic, enriched in Th, U, and light rare earth elements, and depleted in Nb, Ta and Ti. The dolerites are characterized by high Fe2O3tot (11.61-20.39 wt%) and TiO2 (1.62-3.17 wt%), and low MgO (1.73-4.38 wt%), Cr (2.8-10.8 ppm) and Ni (2.5-11.4 ppm). Isotopically, the mafic volcanic rocks have negative whole-rock εNd(t) values (-6.7 to -9.0) and high ISr values (0.71232 to 0.71767), which are slightly depleted compared with the dolerite samples (εNd(t) = -10.3 to -10.4 and ISr = 0.71796 to 0.71923). Zircons in the dolerites have εHf(t) values of -7.6 to -10.9. The mafic volcanic rocks are interpreted to have resulted from the partial melting of an enriched lithospheric mantle source with minor crustal contamination during ascent, whereas the dolerites formed by late-stage crystallization of enriched lithospheric mantle-derived magmas after fractionation of olivine and pyroxene. The formation of these mantle-derived mafic rocks may be attributed to transtension along a NE-trending strike-slip fault zone that was related to oblique subduction of the Paleo-Pacific plate beneath South China. Such underplated mafic magmas would provide sufficient heat for the generation of ultrahigh-temperature metamorphism and S-type granites, and

X-ray microtomography application in pore space reservoir rock.

Science.gov (United States)

Oliveira, M F S; Lima, I; Borghi, L; Lopes, R T

2012-07-01

Characterization of porosity in carbonate rocks is important in the oil and gas industry since a major hydrocarbons field is formed by this lithology and they have a complex media porous. In this context, this research presents a study of the pore space in limestones rocks by x-ray microtomography. Total porosity, type of porosity and pore size distribution were evaluated from 3D high resolution images. Results show that carbonate rocks has a complex pore space system with different pores types at the same facies. Copyright © 2011 Elsevier Ltd. All rights reserved.

ONKALO rock mechanics model (RMM) - Version 2.0

International Nuclear Information System (INIS)

Moenkkoenen, H.; Hakala, M.; Paananen, M.; Laine, E.

2012-02-01

The Rock Mechanics Model of the ONKALO rock volume is a description of the significant features and parameters related to rock mechanics. The main objective is to develop a tool to predict the rock properties, quality and hence the potential for stress failure which can then be used for continuing design of the ONKALO and the repository. This is the second implementation of the Rock Mechanics Model and it includes sub-models of the intact rock strength, in situ stress, thermal properties, rock mass quality and properties of the brittle deformation zones. Because of the varying quantities of available data for the different parameters, the types of presentations also vary: some data sets can be presented in the style of a 3D block model but, in other cases, a single distribution represents the whole rock volume hosting the ONKALO. (orig.)

Forest management type influences diversity and community composition of soil fungi across temperate forest ecosystems

Directory of Open Access Journals (Sweden)

Kezia eGoldmann

2015-11-01

Full Text Available Fungal communities have been shown to be highly sensitive towards shifts in plant diversity and species composition in forest ecosystems. However, little is known about the impact of forest management on fungal diversity and community composition of geographically separated sites. This study examined the effects of four different forest management types on soil fungal communities. These forest management types include age class forests of young managed beech (Fagus sylvatica L., with beech stands age of approximately 30 years, age class beech stands with an age of approximately 70 years, unmanaged beech stands, and coniferous stands dominated by either pine (Pinus sylvestris L. or spruce (Picea abies Karst. which are located in three study sites across Germany. Soil were sampled from 48 study plots and we employed fungal ITS rDNA pyrotag sequencing to assess the soil fungal diversity and community structure.We found that forest management type significantly affects the Shannon diversity of soil fungi and a significant interaction effect of study site and forest management on the fungal OTU richness. Consequently distinct fungal communities were detected in the three study sites and within the four forest management types, which were mainly related to the main tree species. Further analysis of the contribution of soil properties revealed that C/N ratio being the most important factor in all the three study sites whereas soil pH was significantly related to the fungal community in two study sites. Functional assignment of the fungal communities indicated that 38% of the observed communities were Ectomycorrhizal fungi (ECM and their distribution is significantly influenced by the forest management. Soil pH and C/N ratio were found to be the main drivers of the ECM fungal community composition. Additional fungal community similarity analysis revealed the presence of study site and management type specific ECM genera.This study extends our knowledge

Forest Management Type Influences Diversity and Community Composition of Soil Fungi across Temperate Forest Ecosystems.

Science.gov (United States)

Goldmann, Kezia; Schöning, Ingo; Buscot, François; Wubet, Tesfaye

2015-01-01

Fungal communities have been shown to be highly sensitive toward shifts in plant diversity and species composition in forest ecosystems. However, little is known about the impact of forest management on fungal diversity and community composition of geographically separated sites. This study examined the effects of four different forest management types on soil fungal communities. These forest management types include age class forests of young managed beech (Fagus sylvatica L.), with beech stands age of approximately 30 years, age class beech stands with an age of approximately 70 years, unmanaged beech stands, and coniferous stands dominated by either pine (Pinus sylvestris L.) or spruce (Picea abies Karst.) which are located in three study sites across Germany. Soil were sampled from 48 study plots and we employed fungal ITS rDNA pyrotag sequencing to assess the soil fungal diversity and community structure. We found that forest management type significantly affects the Shannon diversity of soil fungi and a significant interaction effect of study site and forest management on the fungal operational taxonomic units richness. Consequently distinct fungal communities were detected in the three study sites and within the four forest management types, which were mainly related to the main tree species. Further analysis of the contribution of soil properties revealed that C/N ratio being the most important factor in all the three study sites whereas soil pH was significantly related to the fungal community in two study sites. Functional assignment of the fungal communities indicated that 38% of the observed communities were Ectomycorrhizal fungi (ECM) and their distribution is significantly influenced by the forest management. Soil pH and C/N ratio were found to be the main drivers of the ECM fungal community composition. Additional fungal community similarity analysis revealed the presence of study site and management type specific ECM genera. This study extends our

Does staff diversity imply openness to diversity?

DEFF Research Database (Denmark)

Lauring, Jakob; Selmer, Jan

2013-01-01

Purpose – Post-secondary educational organizations are currently some of the most diverse settings to be found. However, few educational studies have dealt with staff diversity and hardly any has looked outside the USA. The purpose of this paper is to present a study of members of international...... university departments in Denmark. The authors set out to investigate the relationship between different types of staff diversity and openness to diversity in terms of linguistic, visible, value, and informational heterogeneity. Design/methodology/approach – This study uses responses from 489 staff members......, was unrelated or negatively associated with positive diversity attitudes. Originality/value – Few studies deal with the role of staff diversity and no prior studies the authors know of have examined the link between diversity types and openness to diversity....

On the K-Ar ages of the rocks of two kinds existed in the Kamuikotan metamorphic rocks located in the Horokanai district, Hokkaido

International Nuclear Information System (INIS)

Imaizumi, Masayuki; Ueda, Yoshio.

1981-01-01

In the Fransiscan metamorphic rocks known as the typical high-pressure type metamorphic belts, existence of the blocks of high grade metamorphic rocks of older age in the widely distributed low grade ones of younger age is commonly noticed. This feature has been explained as a phenomenon that the blocks had been tectonically mixed with the surroundings - so-called tectonic blocks - based on the absolute age determination of the component minerals. The Kamuikotan tectonic belt is a melange zone in which occur various kinds of metamorphic rocks of high-pressure and low-pressure types. The high-pressure Kamuikotan metamorphic rocks can be classified into two kinds based upon the modes of occurrence and mineral paragenesis. One is the low grade metamorphic rocks of greenschist and glaucophane schist and the other, the high grade metamorphic rocks of epidote glaucophane schist and epidote amphibolite. The high grade metamorphic rocks always occur as isolated blocks in the low grade metamorphics and associated serpentinite. The report discusses the age of muscovites separated from the two types of high-pressure Kamuikotan metamorphic rocks in the Horokanai district, central Hokkaido. The muscovites separated from the low grade metamorphics of the district give the age of 72 - 116 m.y., while those separated from the high grade metamorphics give the age of 132 - 145 m.y. These ages seem to agree with the idea that the blocks of high grade metamorphics (epidote glaucophane schist and epidote amphibolite) would be the ''tectonic blocks'' - namely the fragments tectonically mixed into the low grade metamorphics of younger age. (author)

Species on the rocks: Systematics and biogeography of the rock-dwelling Ptyodactylus geckos (Squamata: Phyllodactylidae) in North Africa and Arabia.

Science.gov (United States)

Metallinou, Margarita; Červenka, Jan; Crochet, Pierre-André; Kratochvíl, Lukáš; Wilms, Thomas; Geniez, Philippe; Shobrak, Mohammed Y; Brito, José C; Carranza, Salvador

2015-04-01

The understanding of the diversity of species in the Palearctic and the processes that have generated it is still weak for large parts of the arid areas of North Africa and Arabia. Reptiles are among their most remarkable representatives, with numerous groups well adapted to the diverse environments. The Ptyodactylus geckos are a strictly rock-dwelling genus with homogeneous morphology distributed across mountain formations and rocky plateaus from the western African ranges in Mauritania and the Maghreb to the eastern tip of the Arabian Peninsula, with an isolated species in southern Pakistan. Here, we use a broad sampling of 378 specimens, two mitochondrial (12S and cytb) and four nuclear (c-mos, MC1R, ACM4, RAG2) markers in order to obtain the first time-calibrated molecular phylogeny of the genus and place its diversification in a temporal framework. The results reveal high levels of intraspecific variability, indicative of undescribed diversity, and they do not support the monophyly of one species (P. ragazzii). Ptyodactylus species are allopatric across most of their range, which may relate to their high preference for the same type of structural habitat. The onset of their diversification is estimated to have occurred in the Late Oligocene, while that of several deep clades in the phylogeny took place during the Late Miocene, a period when an increase in aridification in North Africa and Arabia initiated. Copyright © 2015 Elsevier Inc. All rights reserved.

Physical modeling of river spanning rock structures: Evaluating interstitial flow, local hydraulics, downstream scour development, and structure stability

Science.gov (United States)

Collins, K.L.; Thornton, C.I.; Mefford, B.; Holmquist-Johnson, C. L.

2009-01-01

Rock weir and ramp structures uniquely serve a necessary role in river management: to meet water deliveries in an ecologically sound manner. Uses include functioning as low head diversion dams, permitting fish passage, creating habitat diversity, and stabilizing stream banks and profiles. Existing information on design and performance of in-stream rock structures does not provide the guidance necessary to implement repeatable and sustainable construction and retrofit techniques. As widespread use of rock structures increases, the need for reliable design methods with a broad range of applicability at individual sites grows as well. Rigorous laboratory testing programs were implemented at the U.S. Bureau of Reclamation (Reclamation) and at Colorado State University (CSU) as part of a multifaceted research project focused on expanding the current knowledge base and developing design methods to improve the success rate of river spanning rock structures in meeting project goals. Physical modeling at Reclamation is being used to measure, predict, and reduce interstitial flow through rock ramps. CSU is using physical testing to quantify and predict scour development downstream of rock weirs and its impact on the stability of rock structures. ?? 2009 ASCE.

Complex resistivity spectra in relation to multiscale pore geometry in carbonates and mixed-siliciclastic rocks

Science.gov (United States)

Norbisrath, Jan Henrik

Carbonate rocks are known to have complex and heterogeneous pore structures, which result from their biogenic origin and strong affinity for diagenetic processes that change their pore structure after burial. The combination of sheer endless variations of precursor biogenic material, depositional environments, and diagenetic effects results in rocks that are interesting to study but intricate to understand. Many schemes to categorize the diversity of carbonate rocks are in use today; most are based on the macropore structure and qualitative thin-section analysis. Many studies, however, acknowledge that micropores have a significant influence on the macroscopic petrophysical rock properties, which are essential to determine reservoir quality. Micropores are, by definition, smaller than the thickness of a thin-section (four major carbonate microporosity types: (1) small intercrystalline, (2) large inter-crystalline, (3) intercement, and (4) micromoldic. Each microporosity type shows a distinct capacity to conduct electrical charge, which largely controls the magnitude and range of cementation factors (m) in rocks with such microporosity type. The BIB-SEM method is also used on a dataset of mixed carbonate-siliciclastic (mudrock) samples with high kerogen and pyrite content. Results show that the nanopore geometry here has little influence on cementation factors, and instead porosity is the main control on m in mudrocks. Cementation factors are crucial for estimates of oil-in-place and water saturation in a wireline application, and a slight change of (assumed) cementation factor can change the interpreter's evaluation from dry hole to discovery. Therefore, accurate determination of cementation factors is a critical task in formation evaluation, similar to accurate estimates of permeability. To achieve this goal, this dissertation utilizes a new approach of using complex resistivity spectra (CRS) to assess the pore geometry and its resulting electrical and fluid flow

Classification and Distribution of Mars Pathfinder Rocks Using Quantitative Morphologic Indices

Science.gov (United States)

Yingst, R. A.; Biederman, K. L.; Monhead, A. M.; Haldemann, A. F. C.; Kowalczyk, M. R.

2004-01-01

The Mars Pathfinder (MPF) landing site was predicted to contain a broad sampling of rock types varying in mineralogical, physical, mechanical and geochemical characteristics. Although rocks have been divided into several spectral categories based on Imager for Mars Pathfinder visible/near-infrared spectra, it has not been fully determined which of these stem from intrinsic mineralogical differences between rocks or rock surfaces, and which result from factors such as physical or chemical weathering. This has made isolation of unique mineralogy's difficult. Efforts in isolating and classifying spectral units among MPF rocks and soils have met with varying degrees of success, and the current understanding is such that many factors influencing spectral signatures cannot be quantified to a sufficient level so they may be removed. The result is that fundamental questions regarding information needed to reveal the present and past interactions between the rocks and rock surfaces and the Martian environment remain unanswered. But it is possible to approach the issue of identifying distinct rock and rock surface types from a different angle.

Effect of Hydrothermal Alteration on Rock Properties in Active Geothermal Setting

Science.gov (United States)

Mikisek, P.; Bignall, G.; Sepulveda, F.; Sass, I.

2012-04-01

Hydrothermal alteration records the physical-chemical changes of rock and mineral phases caused by the interaction of hot fluids and wall rock, which can impact effective permeability, porosity, thermal parameters, rock strength and other rock properties. In this project, an experimental approach has been used to investigate the effects of hydrothermal alteration on rock properties. A rock property database of contrastingly altered rock types and intensities has been established. The database details horizontal and vertical permeability, porosity, density, thermal conductivity and thermal heat capacity for ~300 drill core samples from wells THM12, THM13, THM14, THM17, THM18, THM22 and TH18 in the Wairakei-Tauhara geothermal system (New Zealand), which has been compared with observed hydrothermal alteration type, rank and intensity obtained from XRD analysis and optical microscopy. Samples were selected from clay-altered tuff and intercalated siltstones of the Huka Falls Formation, which acts as a cap rock at Wairakei-Tauhara, and tuffaceous sandstones of the Waiora Formation, which is a primary reservoir-hosting unit for lateral and vertical fluid flows in the geothermal system. The Huka Falls Formation exhibits argillic-type alteration of varying intensity, while underlying Waiora Formations exhibits argillic- and propylithic-type alteration. We plan to use a tempered triaxial test cell at hydrothermal temperatures (up to 200°C) and pressures typical of geothermal conditions, to simulate hot (thermal) fluid percolation through the rock matrix of an inferred "reservoir". Compressibility data will be obtained under a range of operating (simulation reservoir) conditions, in a series of multiple week to month-long experiments that will monitor change in permeability and rock strength accompanying advancing hydrothermal alteration intensity caused by the hot brine interacting with the rock matrix. We suggest, our work will provide new baseline information concerning

Respirable dust measured downwind during rock dust application.

Science.gov (United States)

Harris, M L; Organiscak, J; Klima, S; Perera, I E

2017-05-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

Natural radioactivity of the rocks from the Moon and planets

Energy Technology Data Exchange (ETDEWEB)

Surkov, Yu.A. (AN SSSR, Moscow. Inst. Geokhimii i Analiticheskoj Khimii)

1982-01-01

Tha data on natural radioactivity of rocks (U, Th and K contents) from the Moon, Venus and Mars obtained by means of cosmic means are analyzed. The Moon rock radioactivity has been measured in situ (from orbital vehicles) as well as in the samples of lunar material delivered to the Earth and as for Venus and Mars rocks - by landing vehicles. It has been found that the main specific feature of the Moon and the Earth group planets is the presence of two geomorphological types of the structure of their surface composed by two different types of the matter. The ancient continent regions are made up by feldspar rock - gabbroanorthosite at the Moon (and possibly at the Mars) and granite-metamorphic at the Earth (and possibly at the Venus). The younger ''marine'' regions are composed by basalt rock. The presence at the Moon of two types of crust (marine and continental ones) having a different nature is clearly reflected on the Moon radioactivity map where marine regions (15% of the total surface) which have high radioactivity and continental regions with a relatively low radioactivity can be seen. The discovery of rocks on the Venus surface highly enriched by U, Th and K speaks of their melting from the primary matter in the depth of the Earth. The Marsian rock by the natural radioelement content is close to igneous rocks of the Earth crust of the basic composition and lunar marine basalts.

Natural radioactivity of the rocks from the Moon and planets

International Nuclear Information System (INIS)

Surkov, Yu.A.

1982-01-01

Tha data on natural radioactivity of rocks (U, Th and K contents) from the Moon, Venus and Mars obtained by means of cosmic means are analyzed. The Moon rock radioactivity has been measured in situ (from orbital vehicles) as well as in the samples of lunar material delivered to the Earth and as for Venus and Mars rocks - by landing vehicles. It has been found that the main specific feature of the Moon and the Earth group planets is the presence of two geomorphological types of the structure of their surface composed by two different types of the matter. The ancient contineent regions are made up by feldspar rock - gabbroanorthosite at the Moon (and possibly at the Mars) and granite-metamorphic at the Earth (and possibly at the Venus). The younger ''marine'' regions are composed by basalt rock. The presence at the Moon of two types of crust (marine and continental ones) having a different nature is clearly reflected on the Moon radioactivity map where marine regions (15% of the total surface) which have high radioactivity and continental regions with a relatively low radioactivity can be seen. The discovery of rocks on the Venus surface highly enriched by U, Th and K speaks of their melting from the primary matter in the depth of the Earth. The Marsian rock by the natural radioelement content is close to igneous rocks of the Earth crust of the basic composition and lunar marine basalts

Microstructural controls on the macroscopic behavior of geo-architected rock samples

Science.gov (United States)

Mitchell, C. A.; Pyrak-Nolte, L. J.

2017-12-01

Reservoir caprocks, are known to span a range of mechanical behavior from elastic granitic units to visco-elastic shale units. Whether a rock will behave elastically, visco-elastically or plastically depends on both the compositional and textural or microsctructural components of the rock, and how these components are spatially distributed. In this study, geo-architected caprock fabrication was performed to develop synthetic rock to study the role of rock rheology on fracture deformations, fluid flow and geochemical alterations. Samples were geo-architected with Portland Type II cement, Ottawa sand, and different clays (kaolinite, illite, and Montmorillonite). The relative percentages of these mineral components are manipulated to generate different rock types. With set protocols, the mineralogical content, texture, and certain structural aspects of the rock were controlled. These protocols ensure that identical samples with the same morphological and mechanical characteristics are constructed, thus overcoming issues that may arise in the presence of heterogeneity and high anisotropy from natural rock samples. Several types of homogeneous geo-architected rock samples were created, and in some cases the methods were varied to manipulate the physical parameters of the rocks. Characterization of rocks that the samples exhibit good repeatability. Rocks with the same mineralogical content generally yielded similar compressional and shear wave velocities, UCS and densities. Geo-architected rocks with 10% clay in the matrix had lower moisture content and effective porosities than rocks with no clay. The process by which clay is added to the matrix can strongly affect the resulting compressive strength and physical properties of the geo-architected sample. Acknowledgment: This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Geosciences Research Program under Award Number (DE-FG02-09ER16022).

Metamorphic Rock-Hosted Orogenic Gold Deposit Type as a Source of Langkowala Placer Gold, Bombana, Southeast Sulawesi

Directory of Open Access Journals (Sweden)

Arifudin Idrus

2014-06-01

Full Text Available DOI: 10.17014/ijog.v6i1.114In 2008, placer gold was discovered in Langkowala area (Bombana Regency, Southeast Sulawesi, Indonesia, and more than 60,000 traditional gold miners in the early 2009 have been operating by digging vertical pits and panning active stream sediments. The grade of placer gold ranges from 50 to 140 g/t. Local geological framework indicates that the placer gold is not related to volcanic rock-related hydrothermal gold deposit, e.g. epithermal, skarn or porphyry. This paper describes a preliminary study on possible primary deposit type as a source of the Langkowala (Bombana secondary placer gold. A field study indicates that the Langkowala (Bombana placer/paleoplacer gold is possibly related to gold-bearing quartz veins/veinlets hosted by metamorphic rocks particularly mica schist and metasediments in the area. These quartz veins/veinlets are currently recognized in metamorphic rocks at Wumbubangka Mountains, a northern flank of Rumbia Mountain Range. Sheared, segmented quartz veins/veinlets are of 2 cm to 2 m in width and contain gold in a grade varying between 2 and 61 g/t. At least, there are two generations of the quartz veins. The first generation of quartz vein is parallel to foliation of mica schist and metasediments with general orientation of N 300oE/60o; the second quartz vein generation crosscut the first quartz vein and the foliation of the wallrock. The first quartz veins are mostly sheared/deformed, brecciated, and occasionally sigmoidal, whereas the second quartz veins are relatively massive. The similar quartz veins/veinlets types are also probably present in Mendoke Mountain Range, in the northern side of Langkowala area. This primary gold deposit is called as ‘orogenic gold type’. The orogenic gold deposit could be a new target of gold exploration in Indonesia in the future.

Kimberley rock art dating project

International Nuclear Information System (INIS)

Walsh, G.L.; Morwood, M.

1997-01-01

The art's additional value, unequalled by traditionally recognised artefacts, is its permanent pictorial documentation presenting a 'window' into the otherwise intangible elements of perceptions, vision and mind of pre-historic cultures. Unfortunately it's potential in establishing Kimberley archaeological 'big picture' still remains largely unrecognised. Some of findings of the Kimberley Rock Art Dating Project, using AMS and optical stimulated luminescence (OSL) dating techniques, are outlined. It is estimated that these findings will encourage involvement by a greater diversity of specialist disciplines to tie findings into levels of this art sequence as a primary reference point. The sequence represents a sound basis for selecting specific defined images for targeting detailed studies by a range of dating technique. This effectively removes the undesirable ad hoc sampling of 'apparently old paintings'; a process which must unavoidably remain the case with researchers working on most global bodies of rock art

Modeling rock specimens through 3D printing: Tentative experiments and prospects

Science.gov (United States)

Jiang, Quan; Feng, Xiating; Song, Lvbo; Gong, Yahua; Zheng, Hong; Cui, Jie

2016-02-01

Current developments in 3D printing (3DP) technology provide the opportunity to produce rock-like specimens and geotechnical models through additive manufacturing, that is, from a file viewed with a computer to a real object. This study investigated the serviceability of 3DP products as substitutes for rock specimens and rock-type materials in experimental analysis of deformation and failure in the laboratory. These experiments were performed on two types of materials as follows: (1) compressive experiments on printed sand-powder specimens in different shapes and structures, including intact cylinders, cylinders with small holes, and cuboids with pre-existing cracks, and (2) compressive and shearing experiments on printed polylactic acid cylinders and molded shearing blocks. These tentative tests for 3DP technology have exposed its advantages in producing complicated specimens with special external forms and internal structures, the mechanical similarity of its product to rock-type material in terms of deformation and failure, and its precision in mapping shapes from the original body to the trial sample (such as a natural rock joint). These experiments and analyses also successfully demonstrate the potential and prospects of 3DP technology to assist in the deformation and failure analysis of rock-type materials, as well as in the simulation of similar material modeling experiments.

Rock excavation by pulsed electron beams

International Nuclear Information System (INIS)

Avery, R.T.; Keefe, D.; Brekke, T.L.; Finnie, I.

1976-03-01

If an intense short pulse of megavolt electrons is deposited in a brittle solid, dynamic spalling can be made to occur with removal of material. Experiments were made on several types of hard rock; results are reproducible and well-described theoretically. An accelerator with a rapidly-pulsed scanning electron beam was designed that could tunnel in hard rock about ten times faster than conventional drill/blast methods

Uranium in alkaline rocks

Energy Technology Data Exchange (ETDEWEB)

Murphy, M.; Wollenberg, H.; Strisower, B.; Bowman, H.; Flexser, S.; Carmichael, I.

1978-04-01

Geologic and geochemical criteria were developed for the occurrence of economic uranium deposits in alkaline igneous rocks. A literature search, a limited chemical analytical program, and visits to three prominent alkaline-rock localities (Ilimaussaq, Greenland; Pocos de Caldas, Brazil; and Powderhorn, Colorado) were made to establish criteria to determine if a site had some uranium resource potential. From the literature, four alkaline-intrusive occurrences of differing character were identified as type-localities for uranium mineralization, and the important aspects of these localities were described. These characteristics were used to categorize and evaluate U.S. occurrences. The literature search disclosed 69 U.S. sites, encompassing nepheline syenite, alkaline granite, and carbonatite. It was possible to compare two-thirds of these sites to the type localities. A ranking system identified ten of the sites as most likely to have uranium resource potential.

Uranium in alkaline rocks

International Nuclear Information System (INIS)

Murphy, M.; Wollenberg, H.; Strisower, B.; Bowman, H.; Flexser, S.; Carmichael, I.

1978-04-01

Geologic and geochemical criteria were developed for the occurrence of economic uranium deposits in alkaline igneous rocks. A literature search, a limited chemical analytical program, and visits to three prominent alkaline-rock localities (Ilimaussaq, Greenland; Pocos de Caldas, Brazil; and Powderhorn, Colorado) were made to establish criteria to determine if a site had some uranium resource potential. From the literature, four alkaline-intrusive occurrences of differing character were identified as type-localities for uranium mineralization, and the important aspects of these localities were described. These characteristics were used to categorize and evaluate U.S. occurrences. The literature search disclosed 69 U.S. sites, encompassing nepheline syenite, alkaline granite, and carbonatite. It was possible to compare two-thirds of these sites to the type localities. A ranking system identified ten of the sites as most likely to have uranium resource potential

Multiparameter Monitoring and Prevention of Fault-Slip Rock Burst

OpenAIRE

Hu, Shan-chao; Tan, Yun-liang; Ning, Jian-guo; Guo, Wei-Yao; Liu, Xue-sheng

2017-01-01

Fault-slip rock burst is one type of the tectonic rock burst during mining. A detailed understanding of the precursory information of fault-slip rock burst and implementation of monitoring and early warning systems, as well as pressure relief measures, are essential to safety production in deep mines. This paper first establishes a mechanical model of stick-slip instability in fault-slip rock bursts and then reveals the failure characteristics of the instability. Then, change rule of mining-i...

Mineralogical Control on Microbial Diversity in a Weathered Granite?

Science.gov (United States)

Gleeson, D.; Clipson, N.; McDermott, F.

2003-12-01

the bacterial population in whole rock, which contained approximately 30 separated bands (indicative of the number of bacterial ribotypes), is greater than muscovite (20), K-feldspar (15), and plagioclase feldspar (12) with quartz exhibiting the lowest number (6). These bands were excised from the gel for sequencing, allowing identification of the major populations. An automated approach was also used to assess similarity of bacterial communities present on each sample type, and this allowed for a statistical evaluation of bacterial diversity. Petrographic studies were carried out to assess mineral alteration effects. Scanning electron microscopy (SEM) was used to visualise in-situ bacterial cells.

A Low Cost Structurally Optimized Design for Diverse Filter Types

Science.gov (United States)

Kazmi, Majida; Aziz, Arshad; Akhtar, Pervez; Ikram, Nassar

2016-01-01

A wide range of image processing applications deploys two dimensional (2D)-filters for performing diversified tasks such as image enhancement, edge detection, noise suppression, multi scale decomposition and compression etc. All of these tasks require multiple type of 2D-filters simultaneously to acquire the desired results. The resource hungry conventional approach is not a viable option for implementing these computationally intensive 2D-filters especially in a resource constraint environment. Thus it calls for optimized solutions. Mostly the optimization of these filters are based on exploiting structural properties. A common shortcoming of all previously reported optimized approaches is their restricted applicability only for a specific filter type. These narrow scoped solutions completely disregard the versatility attribute of advanced image processing applications and in turn offset their effectiveness while implementing a complete application. This paper presents an efficient framework which exploits the structural properties of 2D-filters for effectually reducing its computational cost along with an added advantage of versatility for supporting diverse filter types. A composite symmetric filter structure is introduced which exploits the identities of quadrant and circular T-symmetries in two distinct filter regions simultaneously. These T-symmetries effectually reduce the number of filter coefficients and consequently its multipliers count. The proposed framework at the same time empowers this composite filter structure with additional capabilities of realizing all of its Ψ-symmetry based subtypes and also its special asymmetric filters case. The two-fold optimized framework thus reduces filter computational cost up to 75% as compared to the conventional approach as well as its versatility attribute not only supports diverse filter types but also offers further cost reduction via resource sharing for sequential implementation of diversified image

Geochemical investigation of petroleum source rocks by using Rock- Eval data in the Agha-Jari oilfield

Directory of Open Access Journals (Sweden)

Behzad khani

2015-01-01

Full Text Available In this study, 40 drilling cutting of the Pabdeh, Gurpi, kazhdumi and Gadvan Formations from the Agha-Jari Oilfield were analyzed by using Rock-Eval pyrolysis. In order to recognizing sedimentary environmental conditions of studied Formations, they are divided to 4 zones which A (Kazhdumi Formation#187 and C (Kazhdumi Formation#140 zones show reduction conditions by presence of sea organic materials and B (Gadvan Formation #140 and D(Gadvan Formation#187 zones show oxidation conditions by presence of continental organic materials to basin. Based on the Rock-Eval pyrolysis data, the Pabeh, Gurpi, Kazhdumi and Gadvan Formations have variable hydrocarbon generative potential. HI vs. OI plot revealed that the kerogen type in this Formations is a mixed of types II & III. The intensity of matrix effect in the Pabdeh, Gurpi, Kazhdumi and Gadvan Formations was compared by using S2 vs. TOC plot and calculating its regression equation. The results show that the significant amount of S2 adsorption by matrix was happened in the Pabdeh (4.98-6.96 mg HC/gr rock in wells 113 and 121 and Gurpi Formations ‌(4.33 mg HC/gr rock in well 113 which is due to their low thermal maturity‌(Tmax

Analysis of the behavior of radionuclides migration in fractured medium in different types of rocks matrices

International Nuclear Information System (INIS)

Sá, Ludimila Silva Salles de; Silveira, Cláudia Siqueira da; Lima, Zelmo Rodrigues de

2017-01-01

In management of radioactive wastes, the current trend is to dispose the radioactive waste for long life and high activity in permanent repositories of depth, geologically stable and low permeability. Thus, it is relevant to analyze the groundwater movement process, because the mechanism by which the radionuclides in a repository with fractures could return to the surface would be through the groundwater circulation system. A common problem encountered is the modeling of the migration of radionuclides in a fractured medium. The objective of this work is to evaluate the behavior of the migration of radionuclides in two types of rock matrix, considering the following properties: volumetric density, porosity, distribution coefficient and molecular diffusion coefficient. The physical system adopted consists of the matrix rock containing a discrete fracture in a porous medium saturated with water. The partial differential equations that describe the radionuclide movement were discretized by finite differences, and the Implicit Euler method was adopted. While for the convective term the numerical scheme of progressive differences was used

Fractures and Rock Mechanics, Phase 1

DEFF Research Database (Denmark)

Havmøller, Ole; Krogsbøll, Anette

1997-01-01

The main objectives of the project are to combine geological description of fractures, chalk types and rock mechanical properties, and to investigate whether the chosen outcrops can be used as analogues to reservoir chalks. Five chalk types, representing two outcrop localities: Stevns...

Rock excavation by pulsed electron beams

International Nuclear Information System (INIS)

Avery, R.T.; Keefe, D.; Brekke, T.L.; Finnie, I.

1976-01-01

If an intense short pulse of megavolt electrons is deposited in a brittle solid, dynamic spalling can be made to occur with removal of material. Experiments have been made on several types of hard rock; results are reproducible and well-described theoretically. An accelerator with a rapid-pulsed scanning electron-beam has been designed that could tunnel in hard rock about ten times faster than conventional drill/blast methods. (author)

Rock index properties for geoengineering in the Paradox Basin

International Nuclear Information System (INIS)

O'Rourke, J.E.; Rey, P.H.; Alviti, E.; Capps, C.C.

1986-02-01

Previous researchers have investigated the use of a number of rapid index tests that can be used on core samples, or in situ, to determine rock properties needed for geoengineering design, or to predict construction performance in these rock types. Selected research is reviewed, and the correlations of index tests with laboratory tests of rock properties found by the earlier investigators are discussed. The selection and testing of rock core samples from the Gibson Dome No. 1 borehole in Paradox Basin are described. The samples consist primarily of non-salt rock above salt cycle 6, but include some samples of anhydrite and salt cycle 6. The index tests included the point load test, Schmidt hammer rebound test, and abrasion hardness test. Statistical methods were used to analyze the correlations of index test data with laboratory test data of rock properties for the same core. Complete statistical results and computer-generated graphics are presented; these results are discussed in relation to the work of earlier investigations for index testing of similar rock types. Generally, fair to good correlations were obtained for predicting unconfined compressive strength and Young's modulus for sandstone and siltstone, while poorer correlations were found for limestone. This may be due to the large variability of limestone properties compared to the small number of samples. Overall, the use of index tests to assess rock properties at Paradox Basin appears to be practial for some conceptual and preliminary design needs, and the technique should prove useful at any salt repository site. However, it is likely that specific correlations should be demonstrated separately for each site, and the data base for establishing the correlations should probably include at least several hundred data points for each type

Mechanical properties of rock at high temperatures

International Nuclear Information System (INIS)

Kinoshita, Naoto; Abe, Tohru; Wakabayashi, Naruki; Ishida, Tsuyoshi.

1997-01-01

The laboratory tests have been performed in order to investigate the effects of temperature up to 300degC and pressure up to 30 MPa on the mechanical properties of three types of rocks, Inada granite, Sanjoume andesite and Oya tuff. The experimental results indicated that the significant differences in temperature dependence of mechanical properties exist between the three rocks, because of the difference of the factors which determine the mechanical properties of the rocks. The effect of temperature on the mechanical properties for the rocks is lower than that of pressure and water content. Temperature dependence of the mechanical properties is reduced by increase in pressure in the range of pressure and temperature investigated in this paper. (author)

Biodiversity on the Rocks: Macrofauna Inhabiting Authigenic Carbonate at Costa Rica Methane Seeps.

Directory of Open Access Journals (Sweden)

Lisa A Levin

Full Text Available Carbonate communities: The activity of anaerobic methane oxidizing microbes facilitates precipitation of vast quantities of authigenic carbonate at methane seeps. Here we demonstrate the significant role of carbonate rocks in promoting diversity by providing unique habitat and food resources for macrofaunal assemblages at seeps on the Costa Rica margin (400-1850 m. The attendant fauna is surprisingly similar to that in rocky intertidal shores, with numerous grazing gastropods (limpets and snails as dominant taxa. However, the community feeds upon seep-associated microbes. Macrofaunal density, composition, and diversity on carbonates vary as a function of seepage activity, biogenic habitat and location. The macrofaunal community of carbonates at non-seeping (inactive sites is strongly related to the hydrography (depth, temperature, O2 of overlying water, whereas the fauna at sites of active seepage is not. Densities are highest on active rocks from tubeworm bushes and mussel beds, particularly at the Mound 12 location (1000 m. Species diversity is higher on rocks exposed to active seepage, with multiple species of gastropods and polychaetes dominant, while crustaceans, cnidarians, and ophiuroids were better represented on rocks at inactive sites. Macro-infauna (larger than 0.3 mm from tube cores taken in nearby seep sediments at comparable depths exhibited densities similar to those on carbonate rocks, but had lower diversity and different taxonomic composition. Seep sediments had higher densities of ampharetid, dorvilleid, hesionid, cirratulid and lacydoniid polychaetes, whereas carbonates had more gastropods, as well as syllid, chrysopetalid and polynoid polychaetes. Stable isotope signatures and metrics: The stable isotope signatures of carbonates were heterogeneous, as were the food sources and nutrition used by the animals. Carbonate δ13Cinorg values (mean = -26.98‰ ranged from -53.3‰ to +10.0‰, and were significantly heavier than

Effects of atmospheric moisture on rock resistivity.

Science.gov (United States)

Alvarez, R.

1973-01-01

This study examines the changes in resistivity of rock samples as induced by atmospheric moisture. Experiments were performed on samples of hematitic sandstone, pyrite, and galena. The sandstone underwent a change in resistivity of four orders of magnitude when it was measured in a vacuum of 500 ntorr and in air of 37% relative humidity. Pyrite and galena showed no variations in resistivity when they were measured under the same conditions. These results, plus others obtained elsewhere, indicate that rocks of the resistive type are affected in their electrical properties by atmospheric moisture, whereas rocks of the conductive type are not. The experimental evidence obtained is difficult to reconcile with a model of aqueous electrolytic conduction on the sample surface. It is instead suggested that adsorbed water molecules alter the surface resistivity in a manner similar to that observed in semiconductors and insulators.

Impact of grazing abandonment on floristic diversity in the priority habitat type *9562 Grecian Juniper Woods

Science.gov (United States)

Vrahnakis, Michael; Kazoglou, Yannis; Fotiadis, George; Kakouros, Petros; Nasiakou, Stamatia; Soutsas, Konstantinos

2017-04-01

The habitat type *9562 Grecian juniper woods (Juniperetum excelsae) includes Greek juniper (Juniperus excelsa M. Bieb.) forests and they are found mainly in the western sector of the Prespa National Park, NW Greece. Greek juniper forests are considered extremely rare for EU-28, recommending a priority habitat type in accordance with Directive 92/43/EEC. In addition, their ecological importance is great given its high plant taxa richness; they harbor most of the 900 plant taxa found in the western sector of the Park, many of them being important for EU or global scale. The accelerated invasion of deciduous hardwoods is the most significant risk for the habitat, since its rich flora is well-adapted to open light conditions produced by the open spaced Greek junipers. Also, the dense vegetated conditions deprive the regeneration of the photophilous Greek juniper. The invasion results from the lack of its natural controller, i.e. the grazing livestock. It is estimated that the total area of juniper forests for the Devas area decreased to 89% of the area of 1945 in favor of invasive hardwoods. The paper presents the analysis of the floristic diversity of the priority habitat type *9562 Grecian Juniper Woods (Juniperetum excelsae) (GJWs). Four (4) types of juniper forest ranges (GJWs) were distinguished in terms of canopy cover: (a) pure GJWs, (b) mixed open GJWs, (c) open GJWs, and (d) mixed dense GJWs. A total of 171 plant taxa were recorded, and distributed within 43 botanical families; the largest one being Leguminosae (26 taxa). The statistically estimated plant taxa richness for pure GJWs was 116.4, for mixed open 152.6, for open 57.9, and for mixed dense 90.2 taxa. The analysis of α-diversity indices did not reveal any specific trend of diversity for the four GJWs. The behavior of the variability of diversity among the four range types of GJWs was depending on the emphasis the used indices place on properties such as taxa richness or abundance. This fact was

Fracture characteristics in Japanese rock

International Nuclear Information System (INIS)

Ijiri, Yuji; Sawada, Atsushi; Akahori, Kuniaki

1999-11-01

It is crucial for the performance assessment of geosphere to evaluate the characteristics of fractures that can be dominant radionuclide migration pathways from a repository to biosphere. This report summarizes the characteristics of fractures obtained from broad literature surveys and the fields surveys at the Kamaishi mine in northern Japan and at outcrops and galleries throughout the country. The characteristics of fractures described in this report are fracture orientation, fracture shape, fracture frequency, fracture distribution in space, transmissivity of fracture, fracture aperture, fracture fillings, alteration halo along fracture, flow-wetted surface area in fracture, and the correlation among these characteristics. Since granitic rock is considered the archetype fractured media, a large amount of fracture data is available in literature. In addition, granitic rock has been treated as a potential host rock in many overseas programs, and has JNC performed a number of field observations and experiments in granodiorite at the Kamaishi mine. Therefore, the characteristics of fractures in granitic rock are qualitatively and quantitatively clarified to some extent in this report, while the characteristics of fractures in another rock types are not clarified. (author)

Thermal Inertia of Rocks and Rock Populations

Science.gov (United States)

Golombek, M. P.; Jakosky, B. M.; Mellon, M. T.

2001-01-01

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Analysis of mechanical behavior of soft rocks and stability control in deep tunnels

Directory of Open Access Journals (Sweden)

Hui Zhou

2014-06-01

Full Text Available Due to the weakness in mechanical properties of chlorite schist and the high in situ stress in Jinping II hydropower station, the rock mass surrounding the diversion tunnels located in chlorite schist was observed with extremely large deformations. This may significantly increase the risk of tunnel instability during excavation. In order to assess the stability of the diversion tunnels laboratory tests were carried out in association with the petrophysical properties, mechanical behaviors and water-weakening properties of chlorite schist. The continuous deformation of surrounding rock mass, the destruction of the support structure and a large-scale collapse induced by the weak chlorite schist and high in situ stress were analyzed. The distributions of compressive deformation in the excavation zone with large deformations were also studied. In this regard, two reinforcement schemes for the excavation of diversion tunnel bottom section were proposed accordingly. This study could offer theoretical basis for deep tunnel construction in similar geological conditions.

X-ray microtomography application in pore space reservoir rock

Energy Technology Data Exchange (ETDEWEB)

Oliveira, M.F.S.; Lima, I. [Nuclear Instrumentation Laboratory, COPPE/UFRJ, P.O. Box 68509, 21.941-972, Rio de Janeiro (Brazil); Borghi, L. [Geology Department, Geosciences Institute, Federal University of Rio de Janeiro, Brazil. (Brazil); Lopes, R.T., E-mail: ricardo@lin.ufrj.br [Nuclear Instrumentation Laboratory, COPPE/UFRJ, P.O. Box 68509, 21.941-972, Rio de Janeiro (Brazil)

2012-07-15

Characterization of porosity in carbonate rocks is important in the oil and gas industry since a major hydrocarbons field is formed by this lithology and they have a complex media porous. In this context, this research presents a study of the pore space in limestones rocks by x-ray microtomography. Total porosity, type of porosity and pore size distribution were evaluated from 3D high resolution images. Results show that carbonate rocks has a complex pore space system with different pores types at the same facies. - Highlights: Black-Right-Pointing-Pointer This study is about porosity parameter in carbonate rocks by 3D X-Ray Microtomography. Black-Right-Pointing-Pointer This study has become useful as data input for modeling reservoir characterization. Black-Right-Pointing-Pointer This technique was able to provide pores, grains and mineralogical differences among the samples.

Deep rock damage in the San Andreas Fault revealed by P- and S-type fault-zone-guided waves

Science.gov (United States)

Ellsworth, William L.; Malin, Peter E.

2011-01-01

Damage to fault-zone rocks during fault slip results in the formation of a channel of low seismic-wave velocities. Within such channels guided seismic waves, denoted by Fg, can propagate. Here we show with core samples, well logs and Fg-waves that such a channel is crossed by the SAFOD (San Andreas Fault Observatory at Depth) borehole at a depth of 2.7 km near Parkfield, California, USA. This laterally extensive channel extends downwards to at least half way through the seismogenic crust, more than about 7 km. The channel supports not only the previously recognized Love-type- (FL) and Rayleigh-type- (FR) guided waves, but also a new fault-guided wave, which we name FF. As recorded 2.7 km underground, FF is normally dispersed, ends in an Airy phase, and arrives between the P- and S-waves. Modelling shows that FF travels as a leaky mode within the core of the fault zone. Combined with the drill core samples, well logs and the two other types of guided waves, FF at SAFOD reveals a zone of profound, deep, rock damage. Originating from damage accumulated over the recent history of fault movement, we suggest it is maintained either by fracturing near the slip surface of earthquakes, such as the 1857 Fort Tejon M 7.9, or is an unexplained part of the fault-creep process known to be active at this site.

Effects of Weathering on TIR Spectra and Rock Classification

Science.gov (United States)

McDowell, M. L.; Hamilton, V. E.; Riley, D.

2006-03-01

Changes in mineralogy due to weathering are detectable in the TIR and cause misclassification of rock types. We survey samples over a range of lithologies and attempt to provide a method of correction for rock identification from weathered spectra.

Sr–Nd isotopic compositions of Paleoproterozoic metavolcanic rocks from the southern Ashanti volcanic belt, Ghana

OpenAIRE

Dampare, Samuel; Shibata, Tsugio; Asiedu, Daniel; Okano, Osamu; Manu, Johnson; Sakyi, Patrick

2009-01-01

Neodymium (Nd) and strontium (Sr) isotopic data are presented for Paleoproterozoic metavolcanic rocks in the southern part of the Ashanti volcanic belt of Ghana. The metavolcanic rocks are predominantly basalts/basaltic andesites and andesites with minor dacites. Two types of basalts/basaltic andesites (B/A), Type I and Type II, have been identified. The Type I B/A are stratigraphically overlain by the Type II B/A, followed by the andesites and the dacites. The analyzed volcanic rocks commonl...

Linking Diversity and Differentiation

Directory of Open Access Journals (Sweden)

Hans-Rolf Gregorius

2010-03-01

Full Text Available Generally speaking, the term differentiation refers to differences between collections for the distribution of specified traits of their members, while diversity deals with (effective numbers of trait states (types. Counting numbers of types implies discrete traits such as alleles and genotypes in population genetics or species and taxa in ecology. Comparisons between the concepts of differentiation and diversity therefore primarily refer to discrete traits. Diversity is related to differentiation through the idea that the total diversity of a subdivided collection should be composed of the diversity within the subcollections and a complement called “diversity between subcollections”. The idea goes back to the perception that the mixing of differentiated collections increases diversity. Several existing concepts of “diversity between subcollections” are based on this idea. Among them, β-diversity and fixation (inadvertently called differentiation are the most prominent in ecology and in population genetics, respectively. The pertaining measures are shown to quantify the effect of differentiation in terms of diversity components, though from a dual perspective: the classical perspective of differentiation between collections for their type compositions, and the reverse perspective of differentiation between types for their collection affiliations. A series of measures of diversity-oriented differentiation is presented that consider this dual perspective at two levels of diversity partitioning: the overall type or subcollection diversity and the joint type-subcollection diversity. It turns out that, in contrast with common notions, the measures of fixation (such as FST or GST refer to the perspective of type rather than subcollection differentiation. This unexpected observation strongly suggests that the popular interpretations of fixation measures must be reconsidered.

Some clastic rocks as parent rocks in beech forests of Brezovica - Južni Kučaj

Directory of Open Access Journals (Sweden)

Joksimović Vesna

2003-01-01

Full Text Available On the large forest areas, where the measures of soil quality improvement are absent or rarely undertaken, the rocks are the sources of a great number of elements in plant nutrition and one of the factors affecting the contents of some elements in plants. The aim of the study is to determine the differences in the contents of Cu, Zn, Mn, Ni, Fe, Cd, Co, Pb and Cr in the beech leaves developed in the same climate conditions, on morphologically similar terrains, composed of different types of sedimentary rocks. This paper presents the study results of the contents of the above elements in argillites, sandstones (grauwackes and microconglomerates occurring as the parent rocks in high beech forests in the region of GJ Bogovina (Brezovica Južni Kučaj and in the leaves of beech developed on these rocks.

A Review of Rock Bolt Monitoring Using Smart Sensors

Directory of Open Access Journals (Sweden)

Gangbing Song

2017-04-01

Full Text Available Rock bolts have been widely used as rock reinforcing members in underground coal mine roadways and tunnels. Failures of rock bolts occur as a result of overloading, corrosion, seismic burst and bad grouting, leading to catastrophic economic and personnel losses. Monitoring the health condition of the rock bolts plays an important role in ensuring the safe operation of underground mines. This work presents a brief introduction on the types of rock bolts followed by a comprehensive review of rock bolt monitoring using smart sensors. Smart sensors that are used to assess rock bolt integrity are reviewed to provide a firm perception of the application of smart sensors for enhanced performance and reliability of rock bolts. The most widely used smart sensors for rock bolt monitoring are the piezoelectric sensors and the fiber optic sensors. The methodologies and principles of these smart sensors are reviewed from the point of view of rock bolt integrity monitoring. The applications of smart sensors in monitoring the critical status of rock bolts, such as the axial force, corrosion occurrence, grout quality and resin delamination, are highlighted. In addition, several prototypes or commercially available smart rock bolt devices are also introduced.

A Review of Rock Bolt Monitoring Using Smart Sensors.

Science.gov (United States)

Song, Gangbing; Li, Weijie; Wang, Bo; Ho, Siu Chun Michael

2017-04-05

Rock bolts have been widely used as rock reinforcing members in underground coal mine roadways and tunnels. Failures of rock bolts occur as a result of overloading, corrosion, seismic burst and bad grouting, leading to catastrophic economic and personnel losses. Monitoring the health condition of the rock bolts plays an important role in ensuring the safe operation of underground mines. This work presents a brief introduction on the types of rock bolts followed by a comprehensive review of rock bolt monitoring using smart sensors. Smart sensors that are used to assess rock bolt integrity are reviewed to provide a firm perception of the application of smart sensors for enhanced performance and reliability of rock bolts. The most widely used smart sensors for rock bolt monitoring are the piezoelectric sensors and the fiber optic sensors. The methodologies and principles of these smart sensors are reviewed from the point of view of rock bolt integrity monitoring. The applications of smart sensors in monitoring the critical status of rock bolts, such as the axial force, corrosion occurrence, grout quality and resin delamination, are highlighted. In addition, several prototypes or commercially available smart rock bolt devices are also introduced.

Large-scale indicators for monitoring forest diversity of the main forest types in Calabria (Italy

Directory of Open Access Journals (Sweden)

Infusino M

2017-02-01

Full Text Available Recently, the Society’s perception of forest resources has gone through significant changes. Forest ecosystems play a multifunctional role and host an important portion of the whole biodiversity, particularly in the Mediterranean area. Remote sensing technologies provide a unique way to obtain spatially extensive information on forest ecosystems, but relatively few studies used such information to evaluate forest habitat and biotic diversity. In this paper we evaluate the effectiveness of remote sensing to predict forest diversity by linking remotely sensed information with diversity metrics obtained from ground measurements of butterfly diversity. The field work was carried out in Calabria in four different forest types (beech, chestnut, black pine and silver fir forests. The sampling of Lepidoptera was carried out by LED light traps. We positioned 9 traps per forest type, for a total of 36 sites chosen to sample the different stages of forest succession in each forest type. Samples were carried out once a month from May to November 2015. Data from in situ butterfly measurements were compared with above ground forest biomass estimated from airborne LiDAR with NDVI estimated from Landsat 8. Results indicated that the Geometridae/Noctuideae ratio of lepidopteran communities was significantly correlated with the tree biomass, its distribution among tree size classes and the NDVI. The Geometridae/Noctuidae ratio, therefore, represents an index easy to calculate, which can be employed to integrate data acquired from remote sensing in order to obtain continuous spatial estimates of forest naturalness.

Present, past and future of the European rock fern Asplenium fontanum: combining distribution modelling and population genetics to study the effect of climate change on geographic range and genetic diversity.

Science.gov (United States)

Bystriakova, Nadia; Ansell, Stephen W; Russell, Stephen J; Grundmann, Michael; Vogel, Johannes C; Schneider, Harald

2014-02-01

Climate change is expected to alter the geographic range of many plant species dramatically. Predicting this response will be critical to managing the conservation of plant resources and the effects of invasive species. The aim of this study was to predict the response of temperate homosporous ferns to climate change. Genetic diversity and changes in distribution range were inferred for the diploid rock fern Asplenium fontanum along a South-North transect, extending from its putative last glacial maximum (LGM) refugia in southern France towards southern Germany and eastern-central France. This study reconciles observations from distribution models and phylogeographic analyses derived from plastid and nuclear diversity. Genetic diversity distribution and niche modelling propose that genetic diversity accumulates in the LGM climate refugium in southern France with the formation of a diversity gradient reflecting a slow, post-LGM range expansion towards the current distribution range. Evidence supports the fern's preference for outcrossing, contradicting the expectation that homosporous ferns would populate new sites by single-spore colonization. Prediction of climate and distribution range change suggests that a dramatic loss of range and genetic diversity in this fern is possible. The observed migration is best described by the phalanx expansion model. The results suggest that homosporous ferns reproducing preferentially by outcrossing accumulate genetic diversity primarily in LGM climate refugia and may be threatened if these areas disappear due to global climate change.

A rock-inhabiting ancestor for mutualistic and pathogen-rich fungal lineages

NARCIS (Netherlands)

Gueidan, C.; Ruibal Villaseñor, C.; de Hoog, G.S.; Gorbushina, A.A.; Untereiner, W.A.; Lutzoni, F.

2008-01-01

Rock surfaces are unique terrestrial habitats in which rapid changes in the intensity of radiation, temperature, water supply and nutrient availability challenge the survival of microbes. A specialised, but diverse group of free-living, melanised fungi are amongst the persistent settlers of bare

Thermal conductivity of the rocks in the Bureau of Mines Standard Rock Suite

International Nuclear Information System (INIS)

Morgan, M.T.; West, G.A.

1980-01-01

Thermal conductivities of eight rocks from the Bureau of Mines Standard Rock Suite were measured in air over the temperature range 373 to 533 0 K (100 to 260 0 C). The thermal conductivities of these rocks were measured to furnish standards for future comparisons with host rock from prospective nuclear waste repository sites. The thermal conductivity at a given temperature decreased by as much as 9% after a specimen had been heated to the maximum temperature (533 0 K), but additional heating cycles had no further effect. This decrease was smallest in the igneous rocks and largest in the sedimentary types. Variations due to orientation were within the precision of measurements (+- 5%). In most cases the thermal conductivities were linear with the reciprocal of the temperature and were within 14% of published data obtained by other methods. Measurements were made by a cut-bar comparison method in which the sample was sandwiched between two reference or metering bars made of Pyroceram 9606 glass-ceramic. The apparatus consisted of a Dynatech Model TCFCM-N20 comparative thermal conductivity analyzer controlled by a Hewlett Packard Model 3052A data acquisition system. A program was written to increment and cycle the temperature in steps between predetermined initial and maximum values. At each step the thermal conductivity was measured after steady-state conditions were established. The rocks furnished by the Bureau of Mines were quarried in large and fairly homogeneous lots for use by researchers at various laboratories. To investigate any anisotropy, cores were taken from each rock cube perpendicular to each of the cube faces. Samples 2 in. in diameter and approx. 0.75 in. thick were prepared from the cores and were dried in a vacuum oven for at least one month prior to taking measurements

Feeding habits of Aspitrigla cuculus (L., 1758 (red gurnard, Lepidotrigla cavillone (Lac., 1802 (large scale gurnard and Trigloporus lastoviza (Brunn., 1768 (rock gurnard around Cyclades and Dodecanese Islands (E. Mediterranean

Directory of Open Access Journals (Sweden)

A. TERRATS

2000-06-01

Full Text Available The feeding habits of the three most abundant gurnard species, red gurnard (Aspitrigla cuculus, large scale gurnard (Lepidotrigla cavillone and rock gurnard (Trigloporus lastoviza in the eastern Mediterranean (Dodecanese and Cyclades, Greece are examined. The stomach contents of the gurnard specimens collected in April and September 1996 by bottom trawling were analyzed. The % frequency of occurrence, % number and % weight of prey types in the stomach contents were evaluated. By weight, Mysidacea and Decapoda dominated in the diet of the three species in both seasons, however the Index of Relative Importance, as well as the percentage frequency of occurrence varied. Rock gurnard presented the most diverse diet whereas the diet of large scale and red gurnard were more specialized. High overlap in terms of number was found between rock and large scale gurnard in May. Rock gurnard had the most divers diet in both seasons.

Study on investigation and evaluation methods of deep seated sedimentary rocks. Chemical weathering, pore water squeezing and relationships of physical properties of sedimentary rocks

International Nuclear Information System (INIS)

Oyama, Takahiro; Suzuki, Koichi

2006-01-01

Chemical weathering, porewater squeezing and physical properties for the sedimentary rocks were examined. Chemical weathering potential of rocks was described by the sulfur as a acceleration factor of weathering and carbonate contents as a neutralization factor of it. The carbonate contents in the rocks were measured accurately by the gas pressure measurement method. Pore water squeezing method was applied for the semi-hard sedimentary rocks (Opalinusclay). The chemical change of extracted pore water under high pressure conditions was estimated. Physical property of sedimentary rocks have relationship among the porosity and permeability and resistivity coefficient in the same rock types. It is possible to estimate the water permeability from the geophysical tests. (author)

Fire effects on rock images and similar cultural resources [Chapter 5

Science.gov (United States)

Roger E. Kelly; Daniel F. McCarthy

2012-01-01

Throughout human global history, people have purposely altered natural rock surfaces by drilling, drawing, painting, incising, pecking, abrading and chiseling images into stone. Some rock types that present suitable media surfaces for these activities are fine-grained sandstones and granites, basalts, volcanic tuff, dolomites, and limestones. Commonly called rock...

Rock pushing and sampling under rocks on Mars

Science.gov (United States)

Moore, H.J.; Liebes, S.; Crouch, D.S.; Clark, L.V.

1978-01-01

Viking Lander 2 acquired samples on Mars from beneath two rocks, where living organisms and organic molecules would be protected from ultraviolet radiation. Selection of rocks to be moved was based on scientific and engineering considerations, including rock size, rock shape, burial depth, and location in a sample field. Rock locations and topography were established using the computerized interactive video-stereophotogrammetric system and plotted on vertical profiles and in plan view. Sampler commands were developed and tested on Earth using a full-size lander and surface mock-up. The use of power by the sampler motor correlates with rock movements, which were by plowing, skidding, and rolling. Provenance of the samples was determined by measurements and interpretation of pictures and positions of the sampler arm. Analytical results demonstrate that the samples were, in fact, from beneath the rocks. Results from the Gas Chromatograph-Mass Spectrometer of the Molecular Analysis experiment and the Gas Exchange instrument of the Biology experiment indicate that more adsorbed(?) water occurs in samples under rocks than in samples exposed to the sun. This is consistent with terrestrial arid environments, where more moisture occurs in near-surface soil un- der rocks than in surrounding soil because the net heat flow is toward the soil beneath the rock and the rock cap inhibits evaporation. Inorganic analyses show that samples of soil from under the rocks have significantly less iron than soil exposed to the sun. The scientific significance of analyses of samples under the rocks is only partly evaluated, but some facts are clear. Detectable quantities of martian organic molecules were not found in the sample from under a rock by the Molecular Analysis experiment. The Biology experiments did not find definitive evidence for Earth-like living organisms in their sample. Significant amounts of adsorbed water may be present in the martian regolith. The response of the soil

Species presence frequency and diversity in different patch types along an altitudinal gradient: Larix chinensis Beissn in Qinling Mountains (China

Directory of Open Access Journals (Sweden)

Minyi Huang

2016-03-01

Full Text Available Forest communities are mosaic systems composed of patches classified into four different developmental patch types: gap patch (G, building patch (B, mature patch (M and degenerate patch (D. To study the mechanisms maintaining diversity in subalpine coniferous forests, species presence frequency and diversity in the four distinct patch types (G, B, M and D of Larix chinensis conifer forests at three altitudinal gradients in the Qinling Mountains were analyzed. Our results were as follows: (1 Different species (or functional groups had distinct presence frequencies in the four different patch types along the altitudinal gradient; (2 Some species or functional groups (species groups sharing similar traits and responses to the environment only occurred in some specific patches. For seed dispersal, species using wind mainly occurred in G and D, while species using small animals mainly occurred in B and M; (3 Species composition of adjacent patch types was more similar than non-adjacent patch types, based on the lower β diversity index of the former; (4 The maximum numbers of species and two diversity indices (D′ and H′ were found in the middle altitudes. Various gap-forming processes and dispersal limitation may be the two major mechanisms determining species diversity in Larix chinensis coniferous forests at the patch scale.

Engineering and Design: Characterization and Measurement of Discontinuities in Rock Slopes

National Research Council Canada - National Science Library

1983-01-01

This ETL provides guidance for characterizing and measuring rock discontinuities on natural slopes or slopes constructed in rock above reservoirs, darn abutments, or other types of constructed slopes...

The Changes of P-fractions and Solubility of Phosphate Rock in Ultisol Treated by Organic Matter and Phosphate Rock

Directory of Open Access Journals (Sweden)

Heru Bagus Pulunggono

2012-09-01

Full Text Available Phosphorus (P is one of the essential elements for plant, however, its availability is mostly very low in acid soils. It is well documented that application of phosphate rock and organic matter are able to change the level of availability of P-form in acid soils. The objective of the research were to evaluate the changes of P-fractions ( resin-P, NaHCO3-Pi, and NaHCO3-Po and phosphate rock dissolution which were induced by application of organic matter (Imperata cylindrica, Pueraria javanica, dan Colopogonium mucunoides and phosphate rock in Utisol Lampung. The experiment was designed in a completely randomized design with three factors and three replications. The first factor was the types of organic matter (I. cylindrica, P. javanica, and C. mucunoides, the second factor was the rate of organic matter (0, 2.5, and 5%, and the third factor was the rate of phosphate rock (0, 40, and 80 mg P kg-1. The results showed that in the rate of 0 and 1% organic matter, the type of organic matter did not affect P-fraction of NaHCO3-Pi, but in the rate of 2.5 and 5%, NaHCO3-Pi due to application of P. javanica, and C. mucunoides higher than due to application of I. cylindrica. However, the increasing rate of organic matter increased NaHCO3-Pi. Then, P-fraction of Resin-Pi was affected by the type of organic matter, the rate of organic matter, and the rate of phosphate rock, respectively. P-fraction of resin-Pi due to application of P. javanica, and C. mucunoides was higher than due to application of I. cylindrica, but the effect of P. javanica, and C. mucunoides was not different. Increasing the rate of organic matter and phosphate rock increased P-fraction of resin-Pi and NaHCO3-Pi, but P-fraction of NaHCO3-Po was not affected by all treatments. Meanwhile, dissolution of phosphate rock was affected by the kind of organic matter and soil reaction. In the rate of 5% organic matter, dissolution of phosphate rock by application of I. cylindrica (70% was higher

Historical rock falls in Yosemite National Park, California (1857-2011)

Science.gov (United States)

Stock, Greg M.; Collins, Brian D.; Santaniello, David J.; Zimmer, Valerie L.; Wieczorek, Gerald F.; Snyder, James B.

2013-01-01

Inventories of rock falls and other types of landslides are valuable tools for improving understanding of these events. For example, detailed information on rock falls is critical for identifying mechanisms that trigger rock falls, for quantifying the susceptibility of different cliffs to rock falls, and for developing magnitude-frequency relations. Further, inventories can assist in quantifying the relative hazard and risk posed by these events over both short and long time scales. This report describes and presents the accompanying rock fall inventory database for Yosemite National Park, California. The inventory database documents 925 events spanning the period 1857–2011. Rock falls, rock slides, and other forms of slope movement represent a serious natural hazard in Yosemite National Park. Rock-fall hazard and risk are particularly relevant in Yosemite Valley, where glacially steepened granitic cliffs approach 1 km in height and where the majority of the approximately 4 million yearly visitors to the park congregate. In addition to damaging roads, trails, and other facilities, rock falls and other slope movement events have killed 15 people and injured at least 85 people in the park since the first documented rock fall in 1857. The accompanying report describes each of the organizational categories in the database, including event location, type of slope movement, date, volume, relative size, probable trigger, impact to humans, narrative description, references, and environmental conditions. The inventory database itself is contained in a Microsoft Excel spreadsheet (Yosemite_rock_fall_database_1857-2011.xlsx). Narrative descriptions of events are contained in the database, but are also provided in a more readable Adobe portable document format (pdf) file (Yosemite_rock_fall_database_narratives_1857-2011.pdf) available for download separate from the database.

Correlation of the activity of the 238 U in soil and 222 Rn in domiciles, with the rocks of cities of the Estado de Chihuahua

International Nuclear Information System (INIS)

Colmenero S, L.; Villalba, L.; Montero C, M.E.

2004-01-01

The state of Chihuahua has numerous locations of uranium, being Pena Blanca the great and more important location of the country. Diverse rock types with important quantities of uranium are distributed by the whole state. The igneous extrusive acid rocks are those that have bigger quantity of uranium, like they are the rhyolites and dacites and these rocks are located in enough proportion by the whole state. Some of the main cities of the state are near to locations or uraniferous rocks, as Aldama, Nuevo Casas Grandes, Chihuahua, Jimenez and Bocoyna, other important cities are not near important locations. It was determined specific activity by gamma spectroscopy of the series of the 238 U in soils and determination of the radon concentration in domiciles of the main cities of the state. They were found high specific activity values in soil in eight of the thirteen analyzed cities and important radon concentrations in three cities. It was found relationship among the specific activity in soil in near cities to uraniferous locations. (Author)

Small-scale bentonite injection test on rock

International Nuclear Information System (INIS)

Pusch, R.

1978-03-01

When radiactive waste is disposed a sealing of the rock is very valuable since it reduces the rate of water percolation and diffusion. In an earlier report injection of bentonite gels by means of over-pressure and subsequent electrophoresis has been suggested. The present report describes a rock test series where bentonite injection was applied. For the test an approximately cubical block of about 1 m 3 was selected. The rock type was diorite with a fairly high frequency of quartz denses. The block was kept in a basin during the test in order to maintain the water saturation. Holes were bored in the block. A bentonite slurry with 1000 percent water content was injected. It was shown that the bentonite had a sealing effect but the depth of extrusion into rock joints was not large because of gelation. Electro-Kinetic injection of montmorillonite was found to be a more promising technique for rock lightening

Grazer diversity interacts with biogenic habitat heterogeneity to accelerate intertidal algal succession.

Science.gov (United States)

Whalen, Matthew A; Aquilino, Kristin M; Stachowicz, John J

2016-08-01

Environmental heterogeneity contributes to coexistence by allowing species with different traits to persist when different species perform best at different times or places. This interaction between niche differences and environmental variability may also help explain relationships between biodiversity and ecosystem functioning, but few data are available to rigorously evaluate this hypothesis. We assessed how a biologically relevant aspect of environmental heterogeneity interacts with species diversity to determine ecosystem processes in a natural rocky intertidal community. We used field removals to factorially manipulate biogenic habitat heterogeneity (barnacles, bare rock, and plots that were 50/50 mixes of the two habitat types) and gastropod grazer species richness and then tracked algal community succession and recovery over the course of 1 yr. We found that herbivore diversity, substrate heterogeneity, and their interaction played unique roles in the peak abundance and timing of occurrence of different algal functional groups. Early successional microalgae were most heavily grazed in diverse herbivore assemblages and those with barnacles present, which was likely due to complementary feeding strategies among all three grazers. In contrast, late successional macroalgae were strongly influenced by the presence of a habitat generalist limpet. In this herbivore's absence, heterogeneous habitats (i.e., mixtures of bare rock and barnacles) experienced the greatest algal accumulation, which was partly a result of complementary habitat use by the remaining herbivores. The complex way habitat identity and heterogeneity altered grazer-algal interactions in our study suggests species' differences and environmental heterogeneity both separately and interactively contribute to the relationship between biodiversity and ecosystem functions. © 2016 by the Ecological Society of America.

Model to Assess the Quality of Magmatic Rocks for Reliable and Sustainable Constructions

Directory of Open Access Journals (Sweden)

Mihaela Toderaş

2017-10-01

Full Text Available Geomechanical assessment of rocks requires knowledge of phenomena that occur under the influence of internal and external factors at a macroscopic or microscopic scale, when rocks are submitted to different actions. To elucidate the quantitative and qualitative geomechanical behavior of rocks, knowing their geological and physical–mechanical characteristics becomes an imperative. Mineralogical, petrographical and chemical analyses provided an opportunity to identify 15 types of igneous rocks (gabbro, diabases, granites, diorites, rhyolites, andesites, and basalts, divided into plutonic and volcanic rocks. In turn, these have been grouped into acidic, neutral (intermediate and basic magmatites. A new ranking method is proposed, based on considering the rock characteristics as indicators of quantitative assessment, and the grading system, by given points, allowing the rocks framing in admissibility classes. The paper is structured into two parts, experimental and interpretation of experimental data, showing the methodology to assess the quality of igneous rocks analyzed, and the results of theoretical and experimental research carried out on the analyzed rock types. The proposed method constitutes an appropriate instrument for assessment and verification of the requirements regarding the quality of rocks used for sustainable construction.

Features of the distribution of uranium in igneous rocks - uranium deposits associated with igneous rocks

International Nuclear Information System (INIS)

Soerensen, H.

1977-01-01

The generally accepted main features of the distribution of uranium and thorium in igneous rocks are briefly reviewed. It is pointed out that uranium in most cases examined is strongly partitioned into the melt during consolidation of magmas and that uranium is concentrated in the most volatile-rich parts of magmas. The mode of emplacement and the consolidation of magmas control the retention or the expulsion of the volatile phase from consolidating magmas and also the distribution of uranium between magmas and the volatile phase. After a brief review of the types of uranium deposits associated with igneous rocks it is concluded that it is difficult to establish universally valid exploration criteria to be used in the search of these types of deposit. It is emphasized, however, that detailed petrological and geochemical studies may be useful in outlining exploration targets. (author)

Engineering rock mass classification of the Olkiluoto investigation site

Energy Technology Data Exchange (ETDEWEB)

Aeikaes, K. [ed.; Hagros, A.; Johansson, E. [Saanio and Riekkola Consulting Engineers, Helsinki (Finland)] [and others

2000-06-01

Olkiluoto in Eurajoki is being investigated as a possible site for the final disposal of spent nuclear fuel from the Finnish nuclear power plants. The selection of the depth, placement and layout of the repository is affected by the constructability of the bedrock. The constructability, in turn, is influenced by several properties of the host rock, such as its Ethology, the extent of fracturing, its hydrogeological properties and rock engineering characteristics and also by the magnitude and orientation of the in situ stresses and the chemistry of the groundwater. The constructability can be evaluated by the application of a rock classification system in which the properties of the host rock are assessed against common rock engineering judgements associated with underground construction. These judgements are based partly on measurements of in situ stresses and the properties of the bedrock determined from rock samples, but an important aspect is also the practical experience which has been gained during underground excavation in similar conditions and rock types. The aim of the engineering rock mass classification was to determine suitable bedrock volumes for the construction of the repository and has used data from the site characterisation programme carried out at Olkiluoto, which consisted of both surface studies and borehole investigations. The classification specifies three categories of constructability - normal, demanding and very demanding. In addition, rock mass quality has also been classified according to the empirical Q-system to enable a comparison to be made. The rock mass parameters that determine the constructability of the bedrock at Olkiluoto depend primarily on the depth and the Ethology, as well as on whether construction takes place in intact or in fractured rock. The differences in the characteristics of intact rock within a single rock type have been shown to be small. The major lithological unit at Olkiluoto, the mica gneiss, lies in the

Recent advances in analysis and prediction of Rock Falls, Rock Slides, and Rock Avalanches using 3D point clouds

Science.gov (United States)

Abellan, A.; Carrea, D.; Jaboyedoff, M.; Riquelme, A.; Tomas, R.; Royan, M. J.; Vilaplana, J. M.; Gauvin, N.

2014-12-01

The acquisition of dense terrain information using well-established 3D techniques (e.g. LiDAR, photogrammetry) and the use of new mobile platforms (e.g. Unmanned Aerial Vehicles) together with the increasingly efficient post-processing workflows for image treatment (e.g. Structure From Motion) are opening up new possibilities for analysing, modeling and predicting rock slope failures. Examples of applications at different scales ranging from the monitoring of small changes at unprecedented level of detail (e.g. sub millimeter-scale deformation under lab-scale conditions) to the detection of slope deformation at regional scale. In this communication we will show the main accomplishments of the Swiss National Foundation project "Characterizing and analysing 3D temporal slope evolution" carried out at Risk Analysis group (Univ. of Lausanne) in close collaboration with the RISKNAT and INTERES groups (Univ. of Barcelona and Univ. of Alicante, respectively). We have recently developed a series of innovative approaches for rock slope analysis using 3D point clouds, some examples include: the development of semi-automatic methodologies for the identification and extraction of rock-slope features such as discontinuities, type of material, rockfalls occurrence and deformation. Moreover, we have been improving our knowledge in progressive rupture characterization thanks to several algorithms, some examples include the computing of 3D deformation, the use of filtering techniques on permanently based TLS, the use of rock slope failure analogies at different scales (laboratory simulations, monitoring at glacier's front, etc.), the modelling of the influence of external forces such as precipitation on the acceleration of the deformation rate, etc. We have also been interested on the analysis of rock slope deformation prior to the occurrence of fragmental rockfalls and the interaction of this deformation with the spatial location of future events. In spite of these recent advances

Variscan thrusting in I- and S-type granitic rocks of the Tribeč Mountains, Western Carpathians (Slovakia: evidence from mineral compositions and monazite dating

Directory of Open Access Journals (Sweden)

Broska Igor

2015-12-01

Full Text Available The Tribeč granitic core (Tatric Superunit, Western Carpathians, Slovakia is formed by Devonian/Lower Carboniferous, calc-alkaline I- and S-type granitic rocks and their altered equivalents, which provide a rare opportunity to study the Variscan magmatic, post-magmatic and tectonic evolution. The calculated P-T-X path of I-type granitic rocks, based on Fe-Ti oxides, hornblende, titanite and mica-bearing equilibria, illustrates changes in redox evolution. There is a transition from magmatic stage at T ca. 800–850 °C and moderate oxygen fugacity (FMQ buffer to an oxidation event at 600 °C between HM and NNO up to the oxidation peak at 480 °C and HM buffer, to the final reduction at ca. 470 °C at ΔNN= 3.3. Thus, the post-magmatic Variscan history recorded in I-type tonalites shows at early stage pronounced oxidation and low temperature shift back to reduction. The S-type granites originated at temperature 700–750 °C at lower water activity and temperature. The P-T conditions of mineral reactions in altered granitoids at Variscan time (both I and S-types correspond to greenschist facies involving formation of secondary biotite. The Tribeč granite pluton recently shows horizontal and vertical zoning: from the west side toward the east S-type granodiorites replace I-type tonalites and these medium/coarse-grained granitoids are vertically overlain by their altered equivalents in greenschist facies. Along the Tribeč mountain ridge, younger undeformed leucocratic granite dykes in age 342±4.4 Ma cut these metasomatically altered granitic rocks and thus post-date the alteration process. The overlaying sheet of the altered granites is in a low-angle superposition on undeformed granitoids and forms “a granite duplex” within Alpine Tatric Superunit, which resulted from a syn-collisional Variscan thrusting event and melt formation ~340 Ma. The process of alteration may have been responsible for shifting the oxidation trend to the observed

Elm genetic diversity and hybridization in the presence of Dutch elm disease

Science.gov (United States)

Johanne Brunet; Raymond P. Guries

2017-01-01

The impact of Dutch elm disease (DED) on the genetic diversity of slippery elm (Ulmus rubra) is summarized and its potential impact on the genetic diversity of other North American native elms, American elm (U. americana), rock elm (U. thomasii), winged elm (U. alata), cedar elm (

A system of nomenclature for rocks in Olkiluoto

International Nuclear Information System (INIS)

Mattila, J.

2006-06-01

Due to international interest in the Finnish deep repository project at Olkiluoto (SW Finland) and the need for collaboration between scientists involved in site investigations for the disposal of spent nuclear fuel in other countries, a well-documented system of rock nomenclature is required, based on existing classification schemes and international recommendations. The BGS (British Geological Survey) rock classification scheme is the most comprehensive rock classification scheme and the basic principles behind it are utilised for the system of nomenclature for rocks in Olkiluoto. The BGS classification system is based on the use of descriptive names and a clear hierarchy, making it possible to classify rocks at different levels depending on the specific goals of the study, the level of available information, and the expertise of the user. Each rock type is assigned a root name, which is based on structural and textural characteristics or modal compositions of the rock and the root names are refined with qualifier terms as prefixes. Qualifier terms refer to the structure or modal composition of the rock. The bedrock at the Olkiluoto site consists of metamorphic and igneous rocks. The metamorphic rocks consist of migmatitic gneisses and (non-migmatitic) gneisses, which are further divided according to their structural characteristics and modal compositions, the former into stromatic, veined, diatexitic gneisses, the latter into mica, quartz, mafic and TGG gneisses. Igneous rocks consist of pegmatitic granites, K-feldspar porphyry and diabases. (orig.)

Exploration of microbial diversity and community structure of Lonar Lake: the only hypersaline meteorite crater lake within basalt rock

Directory of Open Access Journals (Sweden)

Dhiraj ePaul

2016-01-01

Full Text Available Lonar Lake is a hypersaline and hyperalkaline soda lake and the only meteorite impact crater in the world created in the basalt rocks. Although culture-dependent studies have been reported, the comprehensive understanding of microbial community composition and structure of Lonar Lake remain obscure. In the present study, microbial community structure associated with Lonar Lake sediment and water samples was investigated using high throughput sequencing. Microbial diversity analysis revealed the existence of diverse, yet near consistent community composition. The predominance of bacterial phyla Proteobacteria (30% followed by Actinobacteria (24%, Firmicutes (11% and Cyanobacteria (5% was observed. Bacterial phylum Bacteroidetes (1.12%, BD1-5 (0.5%, Nitrospirae (0.41% and Verrucomicrobia (0.28% were detected as relatively minor populations in Lonar Lake ecosystem. Within Proteobacteria, Gammaproteobacteria represented the most abundant population (21-47% among all the sediments and as a minor population in water samples. Bacterial members Proteobacteria and Firmicutes were present significantly higher (p≥0.05 in sediment samples, whereas members of Actinobacteria, Candidate_division_TM7 and Cyanobacteria (p≥0.05 were significantly abundant in water samples. It was noted that compared to other hypersaline soda lakes, Lonar Lake samples formed one distinct cluster, suggesting a different microbial community composition and structure. The present study reports for the first time the different composition of indigenous microbial communities between the sediment and water samples of Lonar Lake. Having better insight of community structure of this Lake ecosystem could be useful in understanding the microbial role in the geochemical cycle for future functional exploration of the unique hypersaline Lonar Lake.

Correlation between thermal gradient and flexure-type deformation as a potential trigger for exfoliation-related rock falls (Invited)

Science.gov (United States)

Collins, B. D.; Stock, G. M.

2010-12-01

temperatures. Consecutive terrestrial lidar data sets collected at a 12-hour interval during this period confirm the magnitude and geometric configuration of deformation. Temperature and light data indicate a direct link to flake deformation, with peak expansion (crack opening) in late-afternoon, within four hours of peak solar radiation and within two hours after peak temperatures (up to 50°C). Likewise, peak contraction (crack closing) occurs in mid-morning at opposite diurnal cycle, synchronous with low solar radiation and air temperature (down to -1°C). We interpret the lag between solar radiation, temperature and deformation to be caused by the response time needed for thermal propagation through the granitic flake itself, but infer that temperature may play the dominant role. With continued data collection we anticipate assessing potential cumulative deformation of the flake, which could contribute to moment-inducing tensile stresses within the entire flake or to crack tip propagation at the attachment points. Thus, this data may provide an explanation for many exfoliation-type rock falls occurring in Yosemite and elsewhere.

Distribution coefficient of radionuclides on rocks for performance assessment of high-level radioactive waste repository

International Nuclear Information System (INIS)

Shibutani, Tomoki; Shibata, Masahiro; Suyama, Tadahiro

1999-11-01

Distribution coefficients of radionuclides on rocks are selected for safety assessment in the 'Second Progress Report on Research and Development for the geological disposal of HLW in Japan (H12 Report)'. The categorized types of rock are granitic rocks (crystalline and acidic rocks), basaltic rocks (crystalline and basic rocks), psammitic rocks (neogene sedimentary (soft)), and tuffaceous-pelitic rocks (pre-neogene sedimentary rocks (hard)). The types of groundwater are FRHP (fresh reducing high-pH), FRLP (fresh reducing low-pH), SRHP (saline reducing high-pH), SRLP (saline reducing low-pH), MRNP (mixing reducing neutral-pH) and FOHP (fresh oxidizing high-pH) groundwater. The elements to be surveyed are Ni, Se, Zr, Nb, Tc, Pd, Sn, Cs, Sm, Pb, Ra, Ac, Th, Pa, U, Np, Pu, Am and Cm. Distribution coefficients are collected from literatures describing batch sorption experimental results, and are selected under consideration of conservativity. (author)

Martian soil stratigraphy and rock coatings observed in color-enhanced Viking Lander images

Science.gov (United States)

Strickland, E. L., III

1979-01-01

Subtle color variations of martian surface materials were enhanced in eight Viking Lander (VL) color images. Well-defined soil units recognized at each site (six at VL-1 and four at VL-2), are identified on the basis of color, texture, morphology, and contact relations. The soil units at the Viking 2 site form a well-defined stratigraphic sequence, whereas the sequence at the Viking 1 site is only partially defined. The same relative soil colors occur at the two sites, suggesting that similar soil units are widespread on Mars. Several types of rock surface materials can be recognized at the two sites; dark, relatively 'blue' rock surfaces are probably minimally weathered igneous rock, whereas bright rock surfaces, with a green/(blue + red) ratio higher than that of any other surface material, are interpreted as a weathering product formed in situ on the rock. These rock surface types are common at both sites. Soil adhering to rocks is common at VL-2, but rare at VL-1. The mechanism that produces the weathering coating on rocks probably operates planet-wide.

Genetic diversity analysis of Leuconostoc mesenteroides from Korean vegetables and food products by multilocus sequence typing.

Science.gov (United States)

Sharma, Anshul; Kaur, Jasmine; Lee, Sulhee; Park, Young-Seo

2018-06-01

In the present study, 35 Leuconostoc mesenteroides strains isolated from vegetables and food products from South Korea were studied by multilocus sequence typing (MLST) of seven housekeeping genes (atpA, groEL, gyrB, pheS, pyrG, rpoA, and uvrC). The fragment sizes of the seven amplified housekeeping genes ranged in length from 366 to 1414 bp. Sequence analysis indicated 27 different sequence types (STs) with 25 of them being represented by a single strain indicating high genetic diversity, whereas the remaining 2 were characterized by five strains each. In total, 220 polymorphic nucleotide sites were detected among seven housekeeping genes. The phylogenetic analysis based on the STs of the seven loci indicated that the 35 strains belonged to two major groups, A (28 strains) and B (7 strains). Split decomposition analysis showed that intraspecies recombination played a role in generating diversity among strains. The minimum spanning tree showed that the evolution of the STs was not correlated with food source. This study signifies that the multilocus sequence typing is a valuable tool to access the genetic diversity among L. mesenteroides strains from South Korea and can be used further to monitor the evolutionary changes.

Influence of substrate rocks on Fe-Mn crust composition

Science.gov (United States)

Hein, J.R.; Morgan, C.L.

1999-01-01

Principal Component and other statistical analyses of chemical and mineralogical data of Fe-Mn oxyhydroxide crusts and their underlying rock substrates in the central Pacific indicate that substrate rocks do not influence crust composition. Two ridges near Johnston Atoll were dredged repetitively and up to seven substrate rock types were recovered from small areas of similar water depths. Crusts were analyzed mineralogically and chemically for 24 elements, and substrates were analyzed mineralogically and chemically for the 10 major oxides. Compositions of crusts on phosphatized substrates are distinctly different from crusts on substrates containing no phosphorite. However, that relationship only indicates that the episodes of phosphatization that mineralized the substrate rocks also mineralized the crusts that grew on them. A two-fold increase in copper contents in crusts that grew on phosphatized clastic substrate rocks, relative to crusts on other substrate rock types, is also associated with phosphatization and must have resulted from chemical reorganization during diagenesis. Phosphatized crusts show increases in Sr, Zn, Ca, Ba, Cu, Ce, V, and Mo contents and decreases in Fe, Si, and As contents relative to non-phosphatized crusts. Our statistical results support previous studies which show that crust compositions reflect predominantly direct precipitation from seawater (hydrogenetic), and to lesser extents reflect detrital input and diagenetic replacement of parts of the older crust generation by carbonate fluorapatite.

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Correlations between ultrasonic pulse wave velocities and rock properties of quartz-mica schist

Directory of Open Access Journals (Sweden)

Bharti Chawre

2018-06-01

Full Text Available Physico-mechanical properties are critically important parameters for rocks. This study aims to examine some of the rock properties of quartz-mica schist (QMS rocks in a cost-effective manner by establishing correlations between non-destructive and destructive tests. Using simple regression analysis, good correlations were obtained between the pulse wave velocities and the properties of QMS rocks. The results were further improved by using multiple regression analysis as compared to those obtained by the simple linear regression analysis. The results were also compared to the ones obtained by other empirical equations available. The general equations encompassing all types of rocks did not give reliable results of rock properties and showed large relative errors, ranging from 23% to 1146%. It is suggested that empirical correlations must be investigated separately for different types of rocks. The general empirical equations should not be used for the design and planning purposes before they are verified at least on one rock sample from the project site, as they may contain large unacceptable errors. Keywords: Pulse wave velocity, Physico-mechanical properties, Quartz-mica schist (QMS rocks, Non-destructive methods, Static elastic constants, Dynamic elastic constants

On the patterns of abundance and diversity of macrolichens of Chopta-Tunganath in the Garhwal Himalaya.

Science.gov (United States)

Negi, H R

2000-12-01

A total of 3211 colonies of macrolichens, from twelve 50 m x 10 m plots distributed across four macrohabitat (vegetation) types between 1500 m-3700 m in the Chopta-Tunganath landscape of the Garhwal Himalaya, yielded 13 families with 15 genera and 85 species. Lobaria retigera stood out as a broad-niched generalist species with moderate levels of abundance in all the three major microhabitats, viz. rock, soil and wood across 83% of all the plots sampled, whereas Umbilicaria indica emerged as an abundantly occurring specialist confined to rock substrates. Heterodermia incana and Leptogium javanicum appeared to be rare members of the community as they were encountered only once during the field survey. Woody microhabitats turned out to be richer than rock and soil substrates for macrolichens. Amongst the macrohabitats, middle altitude (2500-2800 m) Quercus forest was richest in species and genera followed by high altitude (2900-3200 m) Rhododendron forest, higher altitude grasslands (3300-3700 m) and then the lower elevation (1500 m) Quercus forest. Species, genus and family level alpha- as well as beta-diversities were significantly correlated with each other, implying that higher taxonomic ranks such as genera may be used as surrogates for species thus facilitating cost- and time-effective periodic monitoring of the biodiversity of macrolichens. Dynamics of the diversity of lichen communities in relation to various forms of environmental disturbance including livestock grazing and tourism as dominant land use activities in the higher Himalaya need further research.

'Escher' Rock

Science.gov (United States)

2004-01-01

[figure removed for brevity, see original site] Chemical Changes in 'Endurance' Rocks [figure removed for brevity, see original site] Figure 1 This false-color image taken by NASA's Mars Exploration Rover Opportunity shows a rock dubbed 'Escher' on the southwestern slopes of 'Endurance Crater.' Scientists believe the rock's fractures, which divide the surface into polygons, may have been formed by one of several processes. They may have been caused by the impact that created Endurance Crater, or they might have arisen when water leftover from the rock's formation dried up. A third possibility is that much later, after the rock was formed, and after the crater was created, the rock became wet once again, then dried up and developed cracks. Opportunity has spent the last 14 sols investigating Escher, specifically the target dubbed 'Kirchner,' and other similar rocks with its scientific instruments. This image was taken on sol 208 (Aug. 24, 2004) by the rover's panoramic camera, using the 750-, 530- and 430-nanometer filters. The graph above shows that rocks located deeper into 'Endurance Crater' are chemically altered to a greater degree than rocks located higher up. This chemical alteration is believed to result from exposure to water. Specifically, the graph compares ratios of chemicals between the deep rock dubbed 'Escher,' and the more shallow rock called 'Virginia,' before (red and blue lines) and after (green line) the Mars Exploration Rover Opportunity drilled into the rocks. As the red and blue lines indicate, Escher's levels of chlorine relative to Virginia's went up, and sulfur down, before the rover dug a hole into the rocks. This implies that the surface of Escher has been chemically altered to a greater extent than the surface of Virginia. Scientists are still investigating the role water played in influencing this trend. These data were taken by the rover's alpha particle X-ray spectrometer.

Beta-diversity of ectoparasites at two spatial scales: nested hierarchy, geography and habitat type.

Science.gov (United States)

Warburton, Elizabeth M; van der Mescht, Luther; Stanko, Michal; Vinarski, Maxim V; Korallo-Vinarskaya, Natalia P; Khokhlova, Irina S; Krasnov, Boris R

2017-06-01

Beta-diversity of biological communities can be decomposed into (a) dissimilarity of communities among units of finer scale within units of broader scale and (b) dissimilarity of communities among units of broader scale. We investigated compositional, phylogenetic/taxonomic and functional beta-diversity of compound communities of fleas and gamasid mites parasitic on small Palearctic mammals in a nested hierarchy at two spatial scales: (a) continental scale (across the Palearctic) and (b) regional scale (across sites within Slovakia). At each scale, we analyzed beta-diversity among smaller units within larger units and among larger units with partitioning based on either geography or ecology. We asked (a) whether compositional, phylogenetic/taxonomic and functional dissimilarities of flea and mite assemblages are scale dependent; (b) how geographical (partitioning of sites according to geographic position) or ecological (partitioning of sites according to habitat type) characteristics affect phylogenetic/taxonomic and functional components of dissimilarity of ectoparasite assemblages and (c) whether assemblages of fleas and gamasid mites differ in their degree of dissimilarity, all else being equal. We found that compositional, phylogenetic/taxonomic, or functional beta-diversity was greater on a continental rather than a regional scale. Compositional and phylogenetic/taxonomic components of beta-diversity were greater among larger units than among smaller units within larger units, whereas functional beta-diversity did not exhibit any consistent trend regarding site partitioning. Geographic partitioning resulted in higher values of beta-diversity of ectoparasites than ecological partitioning. Compositional and phylogenetic components of beta-diversity were higher in fleas than mites but the opposite was true for functional beta-diversity in some, but not all, traits.

Hydrological evaluation of five sedimentary rocks for high-level waste disposal

International Nuclear Information System (INIS)

Lomenick, T.F.; Kanehiro, B.Y.

1986-01-01

Utilizing performance criteria that are based upon siting guidelines issued by DOE for postclosure as well as preclosure conditions, a preliminary hydrologic evaluation and ranking is being conducted to determine the suitability of five sedimentary rocks as potential host rocks for a high-level radioactive waste repository. Based upon both quantitative and qualitative considerations, the hydrological ranking of the rocks in order of their potential as a host rock for the disposal of radioactive wastes would be shale, anhydrock, sandstone, chalk, and carbonates, with the first three rocks being significantly better than the remaining two types

Reactive solute transport in an asymmetrical fracture-rock matrix system

Science.gov (United States)

Zhou, Renjie; Zhan, Hongbin

2018-02-01

The understanding of reactive solute transport in a single fracture-rock matrix system is the foundation of studying transport behavior in the complex fractured porous media. When transport properties are asymmetrically distributed in the adjacent rock matrixes, reactive solute transport has to be considered as a coupled three-domain problem, which is more complex than the symmetric case with identical transport properties in the adjacent rock matrixes. This study deals with the transport problem in a single fracture-rock matrix system with asymmetrical distribution of transport properties in the rock matrixes. Mathematical models are developed for such a problem under the first-type and the third-type boundary conditions to analyze the spatio-temporal concentration and mass distribution in the fracture and rock matrix with the help of Laplace transform technique and de Hoog numerical inverse Laplace algorithm. The newly acquired solutions are then tested extensively against previous analytical and numerical solutions and are proven to be robust and accurate. Furthermore, a water flushing phase is imposed on the left boundary of system after a certain time. The diffusive mass exchange along the fracture/rock matrixes interfaces and the relative masses stored in each of three domains (fracture, upper rock matrix, and lower rock matrix) after the water flushing provide great insights of transport with asymmetric distribution of transport properties. This study has the following findings: 1) Asymmetric distribution of transport properties imposes greater controls on solute transport in the rock matrixes. However, transport in the fracture is mildly influenced. 2) The mass stored in the fracture responses quickly to water flushing, while the mass stored in the rock matrix is much less sensitive to the water flushing. 3) The diffusive mass exchange during the water flushing phase has similar patterns under symmetric and asymmetric cases. 4) The characteristic distance

Geomechanical Anisotropy and Rock Fabric in Shales

Science.gov (United States)

Huffman, K. A.; Connolly, P.; Thornton, D. A.

2017-12-01

Digital rock physics (DRP) is an emerging area of qualitative and quantitative scientific analysis that has been employed on a variety of rock types at various scales to characterize petrophysical, mechanical, and hydraulic rock properties. This contribution presents a generic geomechanically focused DRP workflow involving image segmentation by geomechanical constituents, generation of finite element (FE) meshes, and application of various boundary conditions (i.e. at the edge of the domain and at boundaries of various components such as edges of individual grains). The generic workflow enables use of constituent geological objects and relationships in a computational based approach to address specific questions in a variety of rock types at various scales. Two examples are 1) modeling stress dependent permeability, where it occurs and why it occurs at the grain scale; 2) simulating the path and complexity of primary fractures and matrix damage in materials with minerals or intervals of different mechanical behavior. Geomechanical properties and fabric characterization obtained from 100 micron shale SEM images using the generic DRP workflow are presented. Image segmentation and development of FE simulation composed of relatively simple components (elastic materials, frictional contacts) and boundary conditions enable the determination of bulk static elastic properties. The procedure is repeated for co-located images at pertinent orientations to determine mechanical anisotropy. The static moduli obtained are benchmarked against lab derived measurements since material properties (esp. frictional ones) are poorly constrained at the scale of investigation. Once confidence in the input material parameters is gained, the procedure can be used to characterize more samples (i.e. images) than is possible from rock samples alone. Integration of static elastic properties with grain statistics and geologic (facies) conceptual models derived from core and geophysical logs

One Song, Many Works: A Pluralist Ontology of Rock

Directory of Open Access Journals (Sweden)

Dan Burkett

2016-01-01

Full Text Available A number of attempts have been made to construct a plausible ontology of rock music. Each of these ontologies identifies a single type of ontological entity as the “work” in rock music. Yet, all the suggestions advanced to date fail to capture some important considerations about how we engage with music of this tradition. This prompted Lee Brown to advocate a healthy skepticism of higher-order musical ontologies. I argue here that we should instead embrace a pluralist ontology of rock, an ontology that recognizes more than one kind of entity as “the work” in rock music. I contend that this approach has a number of advantages over other ontologies of rock, including that of allowing us to make some comparisons across ontological kinds.

Xenon NMR measurements of permeability and tortuosity in reservoir rocks.

Science.gov (United States)

Wang, Ruopeng; Pavlin, Tina; Rosen, Matthew Scott; Mair, Ross William; Cory, David G; Walsworth, Ronald Lee

2005-02-01

In this work we present measurements of permeability, effective porosity and tortuosity on a variety of rock samples using NMR/MRI of thermal and laser-polarized gas. Permeability and effective porosity are measured simultaneously using MRI to monitor the inflow of laser-polarized xenon into the rock core. Tortuosity is determined from measurements of the time-dependent diffusion coefficient using thermal xenon in sealed samples. The initial results from a limited number of rocks indicate inverse correlations between tortuosity and both effective porosity and permeability. Further studies to widen the number of types of rocks studied may eventually aid in explaining the poorly understood connection between permeability and tortuosity of rock cores.

Ways of distinguishing epigenetic types of gray-colored rocks in sheet-infiltration deposits

International Nuclear Information System (INIS)

Rasulova, S.D.; Yashunskii, Yu.V.

1994-01-01

At an infiltration deposit of uranium in Upper-Cretaceous sandy-clay alluvial deposits (Central Kyzylkum), six stages of postsedimentation epigenetic transformations were distinguished. The genesis of altered rocks was determined mostly by mineralogical methods. A new methodological technique is suggested, which calls for analysis of the textural, structural, and mineral correspondence of ferruginous components of gray-colored and oxidized rocks in the region of their contact and makes it possible to typify epigenetic changes in conditions of repeated change in the direction of geochemical processes

The ammonium content in the Malayer igneous and metamorphic rocks (Sanandaj-Sirjan Zone, Western Iran)

Science.gov (United States)

Ahadnejad, Vahid; Hirt, Ann Marie; Valizadeh, Mohammad-Vali; Bokani, Saeed Jabbari

2011-04-01

The ammonium (NH4+) contents of the Malayer area (Western Iran) have been determined by using the colorimetric method on 26 samples from igneous and metamorphic rocks. This is the first analysis of the ammonium contents of Iranian metamorphic and igneous rocks. The average ammonium content of metamorphic rocks decreases from low-grade to high-grade metamorphic rocks (in ppm): slate 580, phyllite 515, andalusite schist 242. In the case of igneous rocks, it decreases from felsic to mafic igneous types (in ppm): granites 39, monzonite 20, diorite 17, gabbro 10. Altered granitic rocks show enrichment in NH4+ (mean 61 ppm). The high concentration of ammonium in Malayer granites may indicate metasedimentary rocks as protoliths rather than meta-igneous rocks. These granitic rocks (S-types) have high K-bearing rock-forming minerals such as biotite, muscovite and K-feldspar which their potassium could substitute with ammonium. In addition, the high ammonium content of metasediments is probably due to inheritance of nitrogen from organic matter in the original sediments. The hydrothermally altered samples of granitic rocks show highly enrichment of ammonium suggesting external sources which intruded additional content by either interaction with metasedimentary country rocks or meteoritic solutions.

Elemental Geochemistry of Sedimentary Rocks at Yellowknife Bay, Gale Crater, Mars

Science.gov (United States)

McLennan, S. M.; Anderson, R. B.; Bell, J. F.; Bridges, J. C.; Calef, F.; Campbell, J. L.; Clark, B. C.; Clegg, S.; Conrad, P.; Cousin, A.; Des Marais, D. J.; Dromart, G.; Dyar, M. D.; Edgar, L. A.; Ehlmann, B. L.; Fabre, C.; Forni, O.; Gasnault, O.; Gellert, R.; Gordon, S.; Grant, J. A.; Grotzinger, J. P.; Gupta, S.; Herkenhoff, K. E.; Hurowitz, J. A.; King, P. L.; Le Mouélic, S.; Leshin, L. A.; Léveillé, R.; Lewis, K. W.; Mangold, N.; Maurice, S.; Ming, D. W.; Morris, R. V.; Nachon, M.; Newsom, H. E.; Ollila, A. M.; Perrett, G. M.; Rice, M. S.; Schmidt, M. E.; Schwenzer, S. P.; Stack, K.; Stolper, E. M.; Sumner, D. Y.; Treiman, A. H.; VanBommel, S.; Vaniman, D. T.; Vasavada, A.; Wiens, R. C.; Yingst, R. A.; Kemppinen, Osku; Bridges, Nathan; Johnson, Jeffrey R.; Minitti, Michelle; Cremers, David; Farmer, Jack; Godber, Austin; Wadhwa, Meenakshi; Wellington, Danika; McEwan, Ian; Newman, Claire; Richardson, Mark; Charpentier, Antoine; Peret, Laurent; Blank, Jennifer; Weigle, Gerald; Li, Shuai; Milliken, Ralph; Robertson, Kevin; Sun, Vivian; Baker, Michael; Edwards, Christopher; Farley, Kenneth; Griffes, Jennifer; Miller, Hayden; Newcombe, Megan; Pilorget, Cedric; Siebach, Kirsten; Brunet, Claude; Hipkin, Victoria; Marchand, Geneviève; Sánchez, Pablo Sobrón; Favot, Laurent; Cody, George; Steele, Andrew; Flückiger, Lorenzo; Lees, David; Nefian, Ara; Martin, Mildred; Gailhanou, Marc; Westall, Frances; Israël, Guy; Agard, Christophe; Baroukh, Julien; Donny, Christophe; Gaboriaud, Alain; Guillemot, Philippe; Lafaille, Vivian; Lorigny, Eric; Paillet, Alexis; Pérez, René; Saccoccio, Muriel; Yana, Charles; Armiens-Aparicio, Carlos; Rodríguez, Javier Caride; Blázquez, Isaías Carrasco; Gómez, Felipe Gómez; Gómez-Elvira, Javier; Hettrich, Sebastian; Malvitte, Alain Lepinette; Jiménez, Mercedes Marín; Martínez-Frías, Jesús; Martín-Soler, Javier; Martín-Torres, F. Javier; Jurado, Antonio Molina; Mora-Sotomayor, Luis; Caro, Guillermo Muñoz; López, Sara Navarro; Peinado-González, Verónica; Pla-García, Jorge; Manfredi, José Antonio Rodriguez; Romeral-Planelló, Julio José; Fuentes, Sara Alejandra Sans; Martinez, Eduardo Sebastian; Redondo, Josefina Torres; Urqui-O'Callaghan, Roser; Mier, María-Paz Zorzano; Chipera, Steve; Lacour, Jean-Luc; Mauchien, Patrick; Sirven, Jean-Baptiste; Manning, Heidi; Fairén, Alberto; Hayes, Alexander; Joseph, Jonathan; Squyres, Steven; Sullivan, Robert; Thomas, Peter; Dupont, Audrey; Lundberg, Angela; Melikechi, Noureddine; Mezzacappa, Alissa; DeMarines, Julia; Grinspoon, David; Reitz, Günther; Prats, Benito; Atlaskin, Evgeny; Genzer, Maria; Harri, Ari-Matti; Haukka, Harri; Kahanpää, Henrik; Kauhanen, Janne; Kemppinen, Osku; Paton, Mark; Polkko, Jouni; Schmidt, Walter; Siili, Tero; Wray, James; Wilhelm, Mary Beth; Poitrasson, Franck; Patel, Kiran; Gorevan, Stephen; Indyk, Stephen; Paulsen, Gale; Bish, David; Schieber, Juergen; Gondet, Brigitte; Langevin, Yves; Geffroy, Claude; Baratoux, David; Berger, Gilles; Cros, Alain; d'Uston, Claude; Lasue, Jérémie; Lee, Qiu-Mei; Meslin, Pierre-Yves; Pallier, Etienne; Parot, Yann; Pinet, Patrick; Schröder, Susanne; Toplis, Mike; Lewin, Éric; Brunner, Will; Heydari, Ezat; Achilles, Cherie; Oehler, Dorothy; Sutter, Brad; Cabane, Michel; Coscia, David; Israël, Guy; Szopa, Cyril; Robert, François; Sautter, Violaine; Buch, Arnaud; Stalport, Fabien; Coll, Patrice; François, Pascaline; Raulin, François; Teinturier, Samuel; Cameron, James; DeLapp, Dorothea; Dingler, Robert; Jackson, Ryan Steele; Johnstone, Stephen; Lanza, Nina; Little, Cynthia; Nelson, Tony; Williams, Richard B.; Jones, Andrea; Kirkland, Laurel; Baker, Burt; Cantor, Bruce; Caplinger, Michael; Davis, Scott; Duston, Brian; Edgett, Kenneth; Fay, Donald; Hardgrove, Craig; Harker, David; Herrera, Paul; Jensen, Elsa; Kennedy, Megan R.; Krezoski, Gillian; Krysak, Daniel; Lipkaman, Leslie; Malin, Michael; McCartney, Elaina; McNair, Sean; Nixon, Brian; Posiolova, Liliya; Ravine, Michael; Salamon, Andrew; Saper, Lee; Stoiber, Kevin; Supulver, Kimberley; Van Beek, Jason; Van Beek, Tessa; Zimdar, Robert; French, Katherine Louise; Iagnemma, Karl; Miller, Kristen; Summons, Roger; Goesmann, Fred; Goetz, Walter; Hviid, Stubbe; Johnson, Micah; Lefavor, Matthew; Lyness, Eric; Breves, Elly; Fassett, Caleb; Blake, David F.; Bristow, Thomas; Edwards, Laurence; Haberle, Robert; Hoehler, Tori; Hollingsworth, Jeff; Kahre, Melinda; Keely, Leslie; McKay, Christopher; Wilhelm, Mary Beth; Bleacher, Lora; Brinckerhoff, William; Choi, David; Dworkin, Jason P.; Eigenbrode, Jennifer; Floyd, Melissa; Freissinet, Caroline; Garvin, James; Glavin, Daniel; Harpold, Daniel; Jones, Andrea; Mahaffy, Paul; Martin, David K.; McAdam, Amy; Pavlov, Alexander; Raaen, Eric; Smith, Michael D.; Stern, Jennifer; Tan, Florence; Trainer, Melissa; Meyer, Michael; Posner, Arik; Voytek, Mary; Anderson, Robert C.; Aubrey, Andrew; Beegle, Luther W.; Behar, Alberto; Blaney, Diana; Brinza, David; Christensen, Lance; Crisp, Joy A.; DeFlores, Lauren; Ehlmann, Bethany; Feldman, Jason; Feldman, Sabrina; Flesch, Gregory; Jun, Insoo; Keymeulen, Didier; Maki, Justin; Mischna, Michael; Morookian, John Michael; Parker, Timothy; Pavri, Betina; Schoppers, Marcel; Sengstacken, Aaron; Simmonds, John J.; Spanovich, Nicole; Juarez, Manuel de la Torre; Webster, Christopher R.; Yen, Albert; Archer, Paul Douglas; Cucinotta, Francis; Jones, John H.; Niles, Paul; Rampe, Elizabeth; Nolan, Thomas; Fisk, Martin; Radziemski, Leon; Barraclough, Bruce; Bender, Steve; Berman, Daniel; Dobrea, Eldar Noe; Tokar, Robert; Williams, Rebecca M. E.; Cleghorn, Timothy; Huntress, Wesley; Manhès, Gérard; Hudgins, Judy; Olson, Timothy; Stewart, Noel; Sarrazin, Philippe; Vicenzi, Edward; Wilson, Sharon A.; Bullock, Mark; Ehresmann, Bent; Hamilton, Victoria; Hassler, Donald; Peterson, Joseph; Rafkin, Scot; Zeitlin, Cary; Fedosov, Fedor; Golovin, Dmitry; Karpushkina, Natalya; Kozyrev, Alexander; Litvak, Maxim; Malakhov, Alexey; Mitrofanov, Igor; Mokrousov, Maxim; Nikiforov, Sergey; Prokhorov, Vasily; Sanin, Anton; Tretyakov, Vladislav; Varenikov, Alexey; Vostrukhin, Andrey; Kuzmin, Ruslan; Wolff, Michael; Botta, Oliver; Drake, Darrell; Bean, Keri; Lemmon, Mark; Lee, Ella Mae; Sucharski, Robert; Hernández, Miguel Ángel de Pablo; Ávalos, Juan José Blanco; Ramos, Miguel; Kim, Myung-Hee; Malespin, Charles; Plante, Ianik; Muller, Jan-Peter; Navarro-González, Rafael; Ewing, Ryan; Boynton, William; Downs, Robert; Fitzgibbon, Mike; Harshman, Karl; Morrison, Shaunna; Dietrich, William; Kortmann, Onno; Palucis, Marisa; Williams, Amy; Lugmair, Günter; Wilson, Michael A.; Rubin, David; Jakosky, Bruce; Balic-Zunic, Tonci; Frydenvang, Jens; Jensen, Jaqueline Kløvgaard; Kinch, Kjartan; Koefoed, Asmus; Madsen, Morten Bo; Stipp, Susan Louise Svane; Boyd, Nick; Pradler, Irina; Jacob, Samantha; Owen, Tobias; Rowland, Scott; Atlaskin, Evgeny; Savijärvi, Hannu; Boehm, Eckart; Böttcher, Stephan; Burmeister, Sönke; Guo, Jingnan; Köhler, Jan; García, César Martín; Mueller-Mellin, Reinhold; Wimmer-Schweingruber, Robert; McConnochie, Timothy; Benna, Mehdi; Franz, Heather; Bower, Hannah; Brunner, Anna; Blau, Hannah; Boucher, Thomas; Carmosino, Marco; Atreya, Sushil; Elliott, Harvey; Halleaux, Douglas; Rennó, Nilton; Wong, Michael; Pepin, Robert; Elliott, Beverley; Spray, John; Thompson, Lucy; Williams, Joshua; Vasconcelos, Paulo; Bentz, Jennifer; Nealson, Kenneth; Popa, Radu; Kah, Linda C.; Moersch, Jeffrey; Tate, Christopher; Day, Mackenzie; Kocurek, Gary; Hallet, Bernard; Sletten, Ronald; Francis, Raymond; McCullough, Emily; Cloutis, Ed; ten Kate, Inge Loes; Kuzmin, Ruslan; Arvidson, Raymond; Fraeman, Abigail; Scholes, Daniel; Slavney, Susan; Stein, Thomas; Ward, Jennifer; Berger, Jeffrey; Moores, John E.

2014-01-01

Sedimentary rocks examined by the Curiosity rover at Yellowknife Bay, Mars, were derived from sources that evolved from an approximately average martian crustal composition to one influenced by alkaline basalts. No evidence of chemical weathering is preserved, indicating arid, possibly cold, paleoclimates and rapid erosion and deposition. The absence of predicted geochemical variations indicates that magnetite and phyllosilicates formed by diagenesis under low-temperature, circumneutral pH, rock-dominated aqueous conditions. Analyses of diagenetic features (including concretions, raised ridges, and fractures) at high spatial resolution indicate that they are composed of iron- and halogen-rich components, magnesium-iron-chlorine-rich components, and hydrated calcium sulfates, respectively. Composition of a cross-cutting dike-like feature is consistent with sedimentary intrusion. The geochemistry of these sedimentary rocks provides further evidence for diverse depositional and diagenetic sedimentary environments during the early history of Mars.

Elemental geochemistry of sedimentary rocks at Yellowknife Bay, Gale crater, Mars.

Science.gov (United States)

McLennan, S M; Anderson, R B; Bell, J F; Bridges, J C; Calef, F; Campbell, J L; Clark, B C; Clegg, S; Conrad, P; Cousin, A; Des Marais, D J; Dromart, G; Dyar, M D; Edgar, L A; Ehlmann, B L; Fabre, C; Forni, O; Gasnault, O; Gellert, R; Gordon, S; Grant, J A; Grotzinger, J P; Gupta, S; Herkenhoff, K E; Hurowitz, J A; King, P L; Le Mouélic, S; Leshin, L A; Léveillé, R; Lewis, K W; Mangold, N; Maurice, S; Ming, D W; Morris, R V; Nachon, M; Newsom, H E; Ollila, A M; Perrett, G M; Rice, M S; Schmidt, M E; Schwenzer, S P; Stack, K; Stolper, E M; Sumner, D Y; Treiman, A H; VanBommel, S; Vaniman, D T; Vasavada, A; Wiens, R C; Yingst, R A

2014-01-24

Sedimentary rocks examined by the Curiosity rover at Yellowknife Bay, Mars, were derived from sources that evolved from an approximately average martian crustal composition to one influenced by alkaline basalts. No evidence of chemical weathering is preserved, indicating arid, possibly cold, paleoclimates and rapid erosion and deposition. The absence of predicted geochemical variations indicates that magnetite and phyllosilicates formed by diagenesis under low-temperature, circumneutral pH, rock-dominated aqueous conditions. Analyses of diagenetic features (including concretions, raised ridges, and fractures) at high spatial resolution indicate that they are composed of iron- and halogen-rich components, magnesium-iron-chlorine-rich components, and hydrated calcium sulfates, respectively. Composition of a cross-cutting dike-like feature is consistent with sedimentary intrusion. The geochemistry of these sedimentary rocks provides further evidence for diverse depositional and diagenetic sedimentary environments during the early history of Mars.

Rock Art Paintings (Rock Inscriptions) At Gebel Abraq, South Eastern Desert, Egypt

International Nuclear Information System (INIS)

Zaghloul, E.A.; Yehia, M.A.; Elewa, H.H.

2003-01-01

This article presents rock art painting in an area located at the scarp face of Wadi Abraq (Latitude 230 28' N and Longitude 340 45' E). The site is a sandstone protruding ledge rising about 30m. above the ground level. The Gebel Abraq paintings depict a tropical fauna including Elephants, Giraffes, Cows and Ostrich denoting that the area was previously subjected to intensive rainfall during the last pluvial periods. The result was a savana type of land. During recent times, the climate became dry and the communities were forced to move to other areas wher natural springs are still flowing such as Ain Abraq and Bir Abu-Safa. The present founding of the prehistoric paintings (Graffiti) has revealed a mass of evidence that many of the concepts regarding Sahara rock art should be studied

Selection of the host rock for high level radioactive waste repository in China

International Nuclear Information System (INIS)

Jin Yuanxin; Wang Wenguang; Chen Zhangru

2001-01-01

The authors has briefly introduced the experiences of the host rock selection and the host rock types in other countries for high level radioactive waste repository. The potential host rocks in China are investigated. They include granite, tuff, clay, basalt, salt, and loess. The report has expounded the distributions, scale, thickness, mineral and chemical composition, construction, petrogenesis and the ages of the rock. The possibility of these rocks as the host rock has been studied. The six pieces of distribution map of potential rocks have been made up. Through the synthetical study, it is considered that granite as the host rock of high level radioactive waste repository is possible

Diversity of Medicinal Plants among Different Forest-use Types of the Pakistani Himalaya.

Science.gov (United States)

Adnan, Muhammad; Hölscher, Dirk

2012-12-01

Diversity of Medicinal Plants among Different Forest-use Types of the Pakistani Himalaya Medicinal plants collected in Himalayan forests play a vital role in the livelihoods of regional rural societies and are also increasingly recognized at the international level. However, these forests are being heavily transformed by logging. Here we ask how forest transformation influences the diversity and composition of medicinal plants in northwestern Pakistan, where we studied old-growth forests, forests degraded by logging, and regrowth forests. First, an approximate map indicating these forest types was established and then 15 study plots per forest type were randomly selected. We found a total of 59 medicinal plant species consisting of herbs and ferns, most of which occurred in the old-growth forest. Species number was lowest in forest degraded by logging and intermediate in regrowth forest. The most valuable economic species, including six Himalayan endemics, occurred almost exclusively in old-growth forest. Species composition and abundance of forest degraded by logging differed markedly from that of old-growth forest, while regrowth forest was more similar to old-growth forest. The density of medicinal plants positively correlated with tree canopy cover in old-growth forest and negatively in degraded forest, which indicates that species adapted to open conditions dominate in logged forest. Thus, old-growth forests are important as refuge for vulnerable endemics. Forest degraded by logging has the lowest diversity of relatively common medicinal plants. Forest regrowth may foster the reappearance of certain medicinal species valuable to local livelihoods and as such promote acceptance of forest expansion and medicinal plants conservation in the region. ELECTRONIC SUPPLEMENTARY MATERIAL: The online version of this article (doi:10.1007/s12231-012-9213-4) contains supplementary material, which is available to authorized users.

Correlating P-wave Velocity with the Physico-Mechanical Properties of Different Rocks

Science.gov (United States)

Khandelwal, Manoj

2013-04-01

In mining and civil engineering projects, physico-mechanical properties of the rock affect both the project design and the construction operation. Determination of various physico-mechanical properties of rocks is expensive and time consuming, and sometimes it is very difficult to get cores to perform direct tests to evaluate the rock mass. The purpose of this work is to investigate the relationships between the different physico-mechanical properties of the various rock types with the P-wave velocity. Measurement of P-wave velocity is relatively cheap, non-destructive and easy to carry out. In this study, representative rock mass samples of igneous, sedimentary, and metamorphic rocks were collected from the different locations of India to obtain an empirical relation between P-wave velocity and uniaxial compressive strength, tensile strength, punch shear, density, slake durability index, Young's modulus, Poisson's ratio, impact strength index and Schmidt hammer rebound number. A very strong correlation was found between the P-wave velocity and different physico-mechanical properties of various rock types with very high coefficients of determination. To check the sensitivity of the empirical equations, Students t test was also performed, which confirmed the validity of the proposed correlations.

Compact rock material gas permeability properties

Energy Technology Data Exchange (ETDEWEB)

Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

2014-09-15

Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

The Impact of Host Rock Geochemistry on Bacterial Community Structure in Oligotrophic Cave Environments.

Directory of Open Access Journals (Sweden)

Hazel A. Barton

2007-07-01

Full Text Available Despite extremely starved conditions, caves contain surprisingly diverse microbial communities. Our research is geared toward understanding what ecosystems drivers are responsible for this high diversity. To asses the effect of rock fabric and mineralogy, we carried out a comparative geomicrobiology study within Carlsbad Cavern, New Mexico, USA. Samples were collected from two different geologic locations within the cave: WF1 in the Massive Member of the Capitan Formation and sF88 in the calcareous siltstones of the Yates Formation. We examined the organic content at each location using liquid chromatography mass spectroscopy and analyzed microbial community structure using molecular phylogenetic analyses. In order to assess whether microbial activity was leading to changes in the bedrock at each location, the samples were also examined by petrology, X-ray diffraction (XRD and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX. Our results suggest that on the chemically complex Yates Formation (sF88, the microbial community was significantly more diverse than on the limestone surfaces of the Capitan (WF1, despite a higher total number of cells on the latter. Further, the broader diversity of bacterial species at sF88 reflected a larger range of potential metabolic capabilities, presumably due to opportunities to use ions within the rock as nutrients and for chemolithotrophic energy production. The use of these ions at sF88 is supported by the formation of a corrosion residue, presumably through microbial scavenging activities. Our results suggest that rock fabric and mineralogy may be an important driver of ecosystem function and should be carefully reviewed when carrying out microbial community analysis in cave environments.

Rock fragmentation

Energy Technology Data Exchange (ETDEWEB)

Brown, W.S.; Green, S.J.; Hakala, W.W.; Hustrulid, W.A.; Maurer, W.C. (eds.)

1976-01-01

Experts in rock mechanics, mining, excavation, drilling, tunneling and use of underground space met to discuss the relative merits of a wide variety of rock fragmentation schemes. Information is presented on novel rock fracturing techniques; tunneling using electron beams, thermocorer, electric spark drills, water jets, and diamond drills; and rock fracturing research needs for mining and underground construction. (LCL)

Multiparameter Monitoring and Prevention of Fault-Slip Rock Burst

Directory of Open Access Journals (Sweden)

Shan-chao Hu

2017-01-01

Full Text Available Fault-slip rock burst is one type of the tectonic rock burst during mining. A detailed understanding of the precursory information of fault-slip rock burst and implementation of monitoring and early warning systems, as well as pressure relief measures, are essential to safety production in deep mines. This paper first establishes a mechanical model of stick-slip instability in fault-slip rock bursts and then reveals the failure characteristics of the instability. Then, change rule of mining-induced stress and microseismic signals before the occurrence of fault-slip rock burst are proposed, and multiparameter integrated early warning methods including mining-induced stress and energy are established. Finally, pressure relief methods targeting large-diameter boreholes and coal seam infusion are presented in accordance with the occurrence mechanism of fault-slip rock burst. The research results have been successfully applied in working faces 2310 of the Suncun Coal Mine, and the safety of the mine has been enhanced. These research results improve the theory of fault-slip rock burst mechanisms and provide the basis for prediction and forecasting, as well as pressure relief, of fault-slip rock bursts.

Elastic Rock Heterogeneity Controls Brittle Rock Failure during Hydraulic Fracturing

Science.gov (United States)

Langenbruch, C.; Shapiro, S. A.

2014-12-01

For interpretation and inversion of microseismic data it is important to understand, which properties of the reservoir rock control the occurrence probability of brittle rock failure and associated seismicity during hydraulic stimulation. This is especially important, when inverting for key properties like permeability and fracture conductivity. Although it became accepted that seismic events are triggered by fluid flow and the resulting perturbation of the stress field in the reservoir rock, the magnitude of stress perturbations, capable of triggering failure in rocks, can be highly variable. The controlling physical mechanism of this variability is still under discussion. We compare the occurrence of microseismic events at the Cotton Valley gas field to elastic rock heterogeneity, obtained from measurements along the treatment wells. The heterogeneity is characterized by scale invariant fluctuations of elastic properties. We observe that the elastic heterogeneity of the rock formation controls the occurrence of brittle failure. In particular, we find that the density of events is increasing with the Brittleness Index (BI) of the rock, which is defined as a combination of Young's modulus and Poisson's ratio. We evaluate the physical meaning of the BI. By applying geomechanical investigations we characterize the influence of fluctuating elastic properties in rocks on the probability of brittle rock failure. Our analysis is based on the computation of stress fluctuations caused by elastic heterogeneity of rocks. We find that elastic rock heterogeneity causes stress fluctuations of significant magnitude. Moreover, the stress changes necessary to open and reactivate fractures in rocks are strongly related to fluctuations of elastic moduli. Our analysis gives a physical explanation to the observed relation between elastic heterogeneity of the rock formation and the occurrence of brittle failure during hydraulic reservoir stimulations. A crucial factor for understanding

Development of a Unified Rock Bolt Model in Discontinuous Deformation Analysis

Science.gov (United States)

He, L.; An, X. M.; Zhao, X. B.; Zhao, Z. Y.; Zhao, J.

2018-03-01

In this paper, a unified rock bolt model is proposed and incorporated into the two-dimensional discontinuous deformation analysis. In the model, the bolt shank is discretized into a finite number of (modified) Euler-Bernoulli beam elements with the degrees of freedom represented at the end nodes, while the face plate is treated as solid blocks. The rock mass and the bolt shank deform independently, but interact with each other through a few anchored points. The interactions between the rock mass and the face plate are handled via general contact algorithm. Different types of rock bolts (e.g., Expansion Shell, fully grouted rebar, Split Set, cone bolt, Roofex, Garford and D-bolt) can be realized by specifying the corresponding constitutive model for the tangential behavior of the anchored points. Four failure modes, namely tensile failure and shear failure of the bolt shank, debonding along the bolt/rock interface and loss of the face plate, are available in the analysis procedure. The performance of a typical conventional rock bolt (fully grouted rebar) and a typical energy-absorbing rock bolt (D-bolt) under the scenarios of suspending loosened blocks and rock dilation is investigated using the proposed model. The reliability of the proposed model is verified by comparing the simulation results with theoretical predictions and experimental observations. The proposed model could be used to reveal the mechanism of each type of rock bolt in realistic scenarios and to provide a numerical way for presenting the detailed profile about the behavior of bolts, in particular at intermediate loading stages.

The selectivity and promiscuity of brain-neuroregenerative inhibitors between ROCK1 and ROCK2 isoforms: An integration of SB-QSSR modelling, QM/MM analysis and in vitro kinase assay.

Science.gov (United States)

Zhu, L; Yang, Y; Lu, X

2016-01-01

The Rho-associated kinases (ROCKs) have long been recognized as an attractive therapeutic target for various neurological diseases; selective inhibition of ROCK1 and ROCK2 isoforms would result in distinct biological effects on neurogenesis, neuroplasticity and neuroregeneration after brain surgery and traumatic brain injury. However, the discovery and design of isoform-selective inhibitors remain a great challenge due to the high conservation and similarity between the kinase domains of ROCK1 and ROCK2. Here, a structure-based quantitative structure-selectivity relationship (SB-QSSR) approach was used to correlate experimentally measured selectivity with the difference in inhibitor binding to the two kinase isoforms. The resulting regression models were examined rigorously through both internal cross-validation and external blind validation; a nonlinear predictor was found to have high fitting stability and strong generalization ability, which was then employed to perform virtual screening against a structurally diverse, drug-like compound library. Consequently, five and seven hits were identified as promising candidates of 1-o-2 and 2-o-1 selective inhibitors, respectively, from which seven purchasable compounds were tested in vitro using a standard kinase assay protocol to determine their inhibitory activity against and selectivity between ROCK1 and ROCK2. The structural basis, energetic property and biological implication underlying inhibitor selectivity and promiscuity were also investigated systematically using a hybrid quantum mechanics/molecular mechanics (QM/MM) scheme.

An experimental study of velocities under pressure for ancient oceanic rocks

Digital Repository Service at National Institute of Oceanography (India)

Sarma, K.V.L.N.S.

Seismic velocities of Indus suture rock types from Dras-Sanko-Kargil, Kashmir Himalaya, as a function of pressure up to 10 kbar were studied. The high-pressure measurements on the rocks reflect the depthwise increase in velocity, and in general...

Biodiversity of Rock Varnish at Yungay, Atacama Desert, Chile

Science.gov (United States)

Kuhlman, K.; Venkat, P.; La Duc, M.; Kuhlman, G.; McKay, C.

2007-12-01

Rock varnish is a very slow-growing nanostratigraphic coating consisting of approximately 70% clay and 30% iron and manganese oxides of fine-grained clay minerals rich in manganese and iron oxides, which forms on the surfaces of rocks in most semi-arid to hyper-arid climates. Rock varnish has even been postulated to exist on Mars based on surface imagery from several landed missions, and is considered a potential biomarker. However, the mechanism of varnish nucleation and growth remains unknown. Whether or not microbes are involved in the nucleation and growth of rock varnish, the detection of microbes using cultivation or cultivation- independent techniques has demonstrated that varnish provides a microhabitat for microbes. We hypothesized that rock varnish in the Mars-like Yungay region of the Atacama Desert may provide such a microhabitat for microbial life where none has been found to date in the surface soil (< 1 cm). The presence of microbes was investigated using adenosine triphosphate (ATP) assay techniques and culture-independent biomolecular methods. High levels of both total and intracellular ATP were associated with the rock varnish while negligible ATP was found in the surrounding surface soil, suggesting that viable organisms were present. Total DNA was extracted from ground varnish and surrounding surface soil and subjected to trifurcate polymerase chain reactions (PCR). No DNA was recovered from the soil. Amplicons were used to generate ribosomal DNA (rDNA) clone libraries, which suggest the presence of numerous phylogenetically distinct microorganisms in eight Eubacterial clades, Alphaproteobacteria, Betaproteobacteria, Gammaproteobacteria, Cytophaga-Flavobacterium- Bacteroides (CFB), Chloroflexi (green non-sulfur bacteria (GNS)), Gemmatimonadetes, Actinobacteria and Cyanobacteria. The diversity of bacteria found and presence of cyanobacteria suggests that rock varnish provides a niche environment for a cryptoendolithic microbial community where

Migmatitic rocks southwest of the Barberton greenstone belt

International Nuclear Information System (INIS)

Robb, L.J.; Anhaeusser, C.R.

1981-01-01

A geologic survey was done on the migmatitic rocks southwest of the Barberton greenstone belt. A table is given on the chemical analyses of components from migmatic outcrops in this area, as well as on the chemical analyses of some selected rock types found in greenstone xenoliths, together with leuco-biotite tomalite/tronomjemite gneisses in the area surrounding the Boesmanskop syenite pluton. Isotope dating was also used in the survey

Geochemical characteristics of Lower Jurassic source rocks in the Zhongkouzi Basin

Science.gov (United States)

Niu, Haiqing; Han, Xiaofeng; Wei, Jianshe; Zhang, Huiyuan; Wang, Baowen

2018-01-01

Zhongkouzi basin is formed in Mesozoic and Cenozoic and developed on the Hercynian folded belt, the degree of exploration for oil and gas is relatively low hitherto. In order to find out the geochemical characteristics of the source rocks and the potentials for hydrocarbon generation. The research result shows that by analysis the geochemical characteristics of outcrop samples and new core samples in Longfengshan Group, Longfengshan Group are most developed intervals of favorable source rocks. They are formed in depression period of the basin when the sedimentary environments is salt water lacustrine and the water is keeping stable; The organic matter abundance is middle-higher, the main kerogen type is II1-II2 and few samples act as III type, The organic matter maturity is low maturity to medium maturity. The organic matter maturity of the source rock from eastern part of the basin is higher than in the western region. The source rock of Longfengshan Group are in the hydrocarbon generation threshold. The great mass of source rocks are matured and in the peak stage of oil generation.

Rock Core Tests, Proposed Duplicate Lock-Phase 2, Starved Rock Lock and Dam, Illinois River, Illinois

Science.gov (United States)

1975-06-01

defined as being rlppable to marginally rippable by Caterpillar Tractor Company. A cheap, fast seismic refraction survey could verify that this is an...Ore RIPPABLE MARGINAL NGN RIPPABLE Figure 4. Rippability ranges for typical rock types - D9G caterpillar (from performance manual

[Effect of Different Purple Parent Rock on Removal Rates of Nitrogen, Phosphorus and Organics in Landscape Water].

Science.gov (United States)

Huang, Xue-jiao; Liu, Xiao-chen; Li, Zhen-lun; Shi, Wen-hao; Yang, Shan

2015-05-01

In order to understand the impacts of physicochemical properties of purple parent rock on the removal rates of nitrogen, phosphorus and organics in landscape water systems, four types of purple parent rocks including Peng-lai-zhen Formation (S1) , Sha-xi-miao Formation (S2) , Fei-xian-guan Formation (S3) and Sui-ning Formation (S4) , which distribute widely in Chongqing, were selected and autoclaved, and added to unsterile landscape water collected from Chong-de Lake in Southwest University, and the landscape water only was used as control. And several indicators such as total nitrogen and phosphorus and so on of every disposal were investigated periodically. The results indicated that: (1) The highest removal rates of total nitrogen, total phosphorus and Ammonia nitrogen were observed in Sl, which were 45.1%, 62.3% and 90%, respectively; the highest removal rate of COD was 94.5% in S4; the ammonia nitrogen content in the purple parent rocks was not obviously changed before and after the experiments, which indicated that the adsorption of ammonia nitrogen on purple parent rock surface was not the main reason for the decrease of ammonia nitrogen in water. (2) Arsenate had inhibitory effect on the sulfate-reducing bacteria, while copper and magnesium had promoting effect on gram-negative bacteria. (3) The microbial diversity was positively correlated to total nitrogen in water. (4) Based on the PCA analyses of microbial community structure and environmental factors, the mineral elements released from parent rock affected the structure and composition of microbial community in the test water, and then influenced the removal rates of nitrogen, phosphorus and organics in water systems.

Favorability for uranium in tertiary sedimentary rocks, southwestern Montana

International Nuclear Information System (INIS)

Wopat, M.A.; Curry, W.E.; Robins, J.W.; Marjaniemi, D.K.

1977-10-01

Tertiary sedimentary rocks in the basins of southwestern Montana were studied to determine their favorability for potential uranium resources. Uranium in the Tertiary sedimentary rocks was probably derived from the Boulder batholith and from silicic volcanic material. The batholith contains numerous uranium occurrences and is the most favorable plutonic source for uranium in the study area. Subjective favorability categories of good, moderate, and poor, based on the number and type of favorable criteria present, were used to classify the rock sequences studied. Rocks judged to have good favorability for uranium deposits are (1) Eocene and Oligocene strata and undifferentiated Tertiary rocks in the western Three Forks basin and (2) Oligocene rocks in the Helena basin. Rocks having moderate favorability consist of (1) Eocene and Oligocene strata in the Jefferson River, Beaverhead River, and lower Ruby River basins, (2) Oligocene rocks in the Townsend and Clarkston basins, (3) Miocene and Pliocene rocks in the Upper Ruby River basin, and (4) all Tertiary sedimentary formations in the eastern Three Forks basin, and in the Grasshopper Creek, Horse Prairie, Medicine Lodge Creek, Big Sheep Creek, Deer Lodge, Big Hole River, and Bull Creek basins. The following have poor favorability: (1) the Beaverhead Conglomerate in the Red Rock and Centennial basins, (2) Eocene and Oligocene rocks in the Upper Ruby River basin, (3) Miocene and Pliocene rocks in the Townsend, Clarkston, Smith River, and Divide Creek basins, (4) Miocene through Pleistocene rocks in the Jefferson River, Beaverhead River, and Lower Ruby River basins, and (5) all Tertiary sedimentary rocks in the Boulder River, Sage Creek, Muddy Creek, Madison River, Flint Creek, Gold Creek, and Bitterroot basins

CUMULATE ROCKS ASSOCIATED WITH CARBONATE ASSIMILATION, HORTAVÆR COMPLEX, NORTH-CENTRAL NORWAY

Science.gov (United States)

Barnes, C. G.; Prestvik, T.; Li, Y.

2009-12-01

The Hortavær igneous complex intruded high-grade metamorphic rocks of the Caledonian Helgeland Nappe Complex at ca. 466 Ma. The complex is an unusual mafic-silicic layered intrusion (MASLI) because the principal felsic rock type is syenite and because the syenite formed in situ rather than by deep-seated partial melting of crustal rocks. Magma differentiation in the complex was by assimilation, primarily of calc-silicate rocks and melts with contributions from marble and semi-pelites, plus fractional crystallization. The effect of assimilation of calcite-rich rocks was to enhance stability of fassaitic clinopyroxene at the expense of olivine, which resulted in alkali-rich residual melts and lowering of silica activity. This combination of MASLI-style emplacement and carbonate assimilation produced three types of cumulate rocks: (1) Syenitic cumulates formed by liquid-crystal separation. As sheets of mafic magma were loaded on crystal-rich syenitic magma, residual liquid was expelled, penetrating the overlying mafic sheets in flame structures, and leaving a cumulate syenite. (2) Reaction cumulates. Carbonate assimilation, illustrated by a simple assimilation reaction: olivine + calcite + melt = clinopyroxene + CO2 resulted in cpx-rich cumulates such as clinopyroxenite, gabbro, and mela-monzodiorite, many of which contain igneous calcite. (3) Magmatic skarns. Calc-silicate host rocks underwent partial melting during assimilation, yielding a Ca-rich melt as the principal assimilated material and permitting extensive reaction with surrounding magma to form Kspar + cpx + garnet-rich ‘cumulate’ rocks. Cumulate types (2) and (3) do not reflect traditional views of cumulate rocks but instead result from a series of melt-present discontinuous (peritectic) reactions and partial melting of calc-silicate xenoliths. In the Hortavær complex, such cumulates are evident because of the distinctive peritectic cumulate assemblages. It is unclear whether assimilation of �

Analytical methods applied to diverse types of Brazilian propolis

Directory of Open Access Journals (Sweden)

Marcucci Maria

2011-06-01

Full Text Available Abstract Propolis is a bee product, composed mainly of plant resins and beeswax, therefore its chemical composition varies due to the geographic and plant origins of these resins, as well as the species of bee. Brazil is an important supplier of propolis on the world market and, although green colored propolis from the southeast is the most known and studied, several other types of propolis from Apis mellifera and native stingless bees (also called cerumen can be found. Propolis is usually consumed as an extract, so the type of solvent and extractive procedures employed further affect its composition. Methods used for the extraction; analysis the percentage of resins, wax and insoluble material in crude propolis; determination of phenolic, flavonoid, amino acid and heavy metal contents are reviewed herein. Different chromatographic methods applied to the separation, identification and quantification of Brazilian propolis components and their relative strengths are discussed; as well as direct insertion mass spectrometry fingerprinting. Propolis has been used as a popular remedy for several centuries for a wide array of ailments. Its antimicrobial properties, present in propolis from different origins, have been extensively studied. But, more recently, anti-parasitic, anti-viral/immune stimulating, healing, anti-tumor, anti-inflammatory, antioxidant and analgesic activities of diverse types of Brazilian propolis have been evaluated. The most common methods employed and overviews of their relative results are presented.

Radwaste storage in crystalline rocks: a natural analog

International Nuclear Information System (INIS)

Brookins, D.G.; Abashian, M.S.; Cohen, L.H.; Wollenberg, H.A.

1982-01-01

The Eldora-Bryan Stock (Colorado) intruded the 1.4-1.6 billion year old metamorphic rocks of the Idaho Springs Formation 55 million years ago. The stock may be considered a giant analog of a radwaste form without canister or engineered backfill barriers. The authors' lanthanide studies show the following: (1) The intrusive rocks remained as a closed system. (2) Lanthanide/chondrite versus ionic radius plots show only local redistribution in the immediate contact zone, and that rocks in this zone have not gained lanthanides from the magma. (3) No whole rock perturbations for the lanthanides are noted at distances greater than 3 m from the contact. Stable oxygen isotopic variations show a narrow 9.0 +- 0.3 per mille range for the intrusive rocks and whole rock values from 7.6 to 10.0 per mille for the intruded rocks. The authors conclude: (1) The Idaho Springs Formation was not penetrated by hydrothermal fluids from the Eldora-Bryan magma except possibly on a local scale within 3 m of the contact. (2) The light lanthanides may be locally redistributed in the immediate contact zone, but without additions from the magma. (3) The oxygen isotopic data imply lack of hydrothermal fluids from the magma penetrating the intruded rocks, even in the highest temperature contact zones. Whole rock data imply closed system conditions for Rb, Sr, Th, U, Pb even where mineral ages have been lowered. Data for Co, Cr, Sc, Fe, Cs also indicate retention in whole rock systems and no exchange with the magma. The combined chemical, isotopic, petrographic and theoretical data and calculations indicate suitability of rocks of the Idaho Springs Formation, and thus of many types of crystalline rocks as well, for possible use for the storage of radioactive waste

Bird diversity and distribution in relation to urban landscape types in northern Rwanda.

Science.gov (United States)

Gatesire, T; Nsabimana, D; Nyiramana, A; Seburanga, J L; Mirville, M O

2014-01-01

Using the point count method, linear mixed models, Shannon's diversity index, and Bray-Curtis cluster analysis, we conducted a study of the effect of urban fabric layout on bird diversity and distribution in northern Rwanda. The results showed a significant effect of city landscapes on bird richness and relative abundance; residential neighborhoods, institutional grounds, and informal settlements had the highest species diversity in comparison to other microlandscape types. Riversides were characterized by specialized bird species, commonly known to be restricted to wetland environments. Built-up areas and open field landscapes had comparable results. One Albertine Rift endemic bird species, the Ruwenzori Double-collared Sunbird (Cinnyris stuhlmanni), was recorded. Three migratory birds were found in Musanze city for the first time: the Common Sandpiper (Actitis hypoleucos), the Spotted Flycatcher (Muscicapa striata), and the Willow Warbler (Phylloscopus trochilus). Two bird species have not been previously reported in Rwanda: the Garden Warbler (Sylvia borin) and the Lesser Spotted Eagle (Aquila pomarina). The implications of this study are particularly relevant to urban decision makers who should consider the existence of a great diversity of avian fauna when developing and implementing master plans, especially when villages and cities are in proximity of protected areas or natural reserves.

Rock mechanics stability at Olkiluoto, Haestholmen, Kivetty and Romuvaara

International Nuclear Information System (INIS)

Johansson, E.; Rautakorpi, J.

2000-02-01

Posiva Oy is studying the suitability of the Finnish bedrock for the geological disposal of spent nuclear fuel at four sites, Olkiluoto in Eurajoki, Haestholmen in Loviisa, Kivetty in Aeaenekoski and Romuvaara in Kuhmo. To enable the rock properties to be specified in great detail, the site-selection research programme has included rock mechanics investigations such as the measurement of in-situ rock stress and laboratory tests on rock samples. This report presents the results of the rock mechanics analyses performed on the main rock types at the Olkiluoto, Romuvaara, Kivetty and Haestholmen sites. The objective of this study was to assess the near-field stability of the final disposal tunnels and deposition holes at each of the investigation sites. Two empirical methods and a numerical method based on three-dimensional element code (3DEC) were used the analysis tools. A statistical approach was used to select the necessary input data and to specify the cases being analysed. The stability of the KBS-3 and MLH (Medium Long Hole) repository concepts during the pre-closure and post-closure phases was analysed. The repository depths investigated lay between 300 m and 700 m. The empirical methods are based on the study of the ratios between rock strength and the in-situ stress which could result in possible fracturing of the rock mass. Interpretation of the numerical analyses is based on the assumption of an elastic distribution of stress around the disposal tunnel and the deposition hole and the brittle rock strength criterion. The results obtained in this study indicate that in general, the rock mechanics conditions during the pre-closure and post-closure phases at each of the investigated sites remain good and stable between the studied depth levels, especially when the deposition rooms are oriented in a direction parallel to the major in-situ stress. If the disposal tunnels are orientated in a direction perpendicular to the major in-situ stress, the resultant

Alkali gabbronorite, ultra-KREEPy melt rock and the diverse suite of clasts in North Ray crater feldspathic fragmental breccia 67975

International Nuclear Information System (INIS)

Lindstrom, M.M.

1984-01-01

Lunar breccia 67975 is a feldspathic fragmental breccia from North Ray crater, Apollo 16. It contains clasts of alkali gabbronorite and ultra-KREEPy mafic fragment-laden melt breccias, which are unique among Apollo 16 samples. Both are alkali- and iron-rich rocks with moderate to high REE concentrations. They more strongly resemble Apollo 14 gabbronorites and alkali anorthosites and KREEP-rich rocks than they do other Apollo 16 samples. The other clasts in 67975 are the ferroan anorthosites, feldspathic melt rocks, and magnesian granulites, which are typical of other feldspathic fragmental breccias. Examination of bulk and mineral compositions of other breccias and melt rocks suggests that alkali gabbronorite may be a minor component in other North Ray crater breccias and feldspathic melt rocks. This implies that alkali gabbronorite was a fairly early (4.0 b.y.) crustal component in the North Ray crater region

Elbow, forearm, wrist, and hand injuries among sport rock climbers.

Science.gov (United States)

Holtzhausen, L M; Noakes, T D

1996-07-01

Sport rock climbing with its repetitive high-torque movements in gaining the ascent of a rock face or wall, often in steep overhanging positions, is associated with a unique distribution and form of upper limb injuries. In this article, we review the biomechanical aspects of sport rock climbing and the types of injuries commonly encountered in the forearm, wrist, and hand regions of elite sport rock climbers. Because elbow, forearm, wrist, and hand injuries predominate, representing 62% of the total injuries encountered, these anatomical areas have been selected for review. The predominant source of data are the published work of Bollen et al. The remaining sources were obtained through electronic search of the Medline and Current Contents Databases (last searched May 1995). German and French articles were included in the search criteria. Only studies dealing with acute soft tissue and overuse injuries amongst sport rock climbers were selected. Data were extracted directly from the sourced articles. The following injuries have been described in detail with regard to their presentation, diagnosis, treatment, and prevention amongst sport rock climbers: medial epicondylitis, brachialis tendonitis, biceps brachii tendonitis, ulnar collateral ligament sprain of the elbow, carpal tunnel syndrome, digital flexor tendon pulley sheath tears, interphalangeal joint effusions, fixed flexion deformities of the interphalangeal joints, and collateral ligament tears of the interphalangeal joints. Many of the injuries are specific to the handhold types used by the rock climber. Accurate diagnosis and effective treatment of these unique injuries will be facilitated by a wider understanding of the biomechanical aspects of rock climbing and an awareness of the patterns and incidence of injuries in this sport.

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

Establishment of land model at the Shika Nuclear Power Plant. Mainly, on rock board classification

International Nuclear Information System (INIS)

Katagawa, Hideki; Hashimoto, Toru; Hirano, Shuji

1999-01-01

In order to grasp engineering properties of basic land of constructions, there is rock board classification as a method to classify whole of rock board to some groups considerable to be nearly equal on its properties. Among the method, various methods in response to its aim and characteristics are devised, and for a classification to hard rock board, the Denken type rock board classification considering degree of weathering to its main element and so forth are well known. The basic rock board of the Shika Nuclear Power Plant is composed of middle and hard types of rock, and its weathering is limited to its shallow portion, most of which are held at fresh condition. For such land, a new classification standard in response to characteristics of land was established. Here were introduced on a progress to establish a new classification standard, its application results and rock board properties. (G.K.)

Relationship between fluvial clastic sediment and source rock abundance in Rapti river basin of central Nepal Himalayas

International Nuclear Information System (INIS)

Tamrakar Naresh Kazi; Shresth Madhusudan Bhakta

2008-01-01

Many tributaries from carbonate sedimentary, metamorphic and igneous rocks of the Lesser Himalayan and clastic sedimentary rocks of the Sub-Himalayan Ranges carry gravelly sediments to the Rapti River. River bar sediments were analyzed for composition and texture to evaluate downstream changes in properties, and to establish relationship between proportion of clasts and the abundance of rock types in the source areas. Percent quartzite clast or granite clast increases whereas that of carbonate, schist or slate decreases along downstream. The largest grain size decreases downstream, whereas fatness index and sphericity tend to increase. Despite of little diminish in relative abundance of rock types in source areas along the river, the relative proportion of corresponding clast type shows rapid reduction (e.g. slate or phyllite or carbonate clasts) or rapid enhancement (e.g. granite clast). The relationships of quartzite clast and schist clasts with their corresponding source rocks are statistically significant suggesting that these clasts can provide clue to source rock abundance. About 85 to 94% of the gravel clasts represent rock types of the Lesser Himalayan Range suggesting that this range has been contributing enormous amount of sediments.

Validation of choice and determination of geotechnology parameters with regard to stress–strain state of rocks

Science.gov (United States)

Freidin, AM; Neverov, SA; Neverov, AA; Konurin, AI

2018-03-01

The paper illustrates efficiency and reliability of types of rock mass stress state conditioned by geological and structural features of rocks in design, selection and validation of geotechnology parameters. The authors of the paper present calculation of stresses in rock mass under sublevel stoping depending on the type of the geosphere and on the depth of the ore body occurrence.

Control over surrounding rocks deformation of soft floor and whole-coal gateways with trapezoidal supports

Energy Technology Data Exchange (ETDEWEB)

Zhai, X.; Li, D.; Shao, Q.; Sun, Y. [Henan Polytechnic University, Jaozuo (China). Dept. of Resource and Material Engineering

2005-06-01

The coal seams of Guengcun Coal mine of Yima Coal Group Co. Ltd. are prone to spontaneous combustion. Fully mechanized longwall mining with sublevel caving is used as the mining method. Based on the characteristics of the gateways of the 1301 coal face and of the roof coal seams, the natural equilibrium arch theory was used to design the parameters of 11 mine-type metal supports. Then, in-situ supporting experiments were carried out. The results indicate that under the action of virgin rock stress, the width of broken rocks zone of surrounding rocks is 1.7-2.0 m in the return heading and 1.1-1.3 m in the outgoing headway and their surrounding rocks belong to the IV-type soft rock and the III-type common surrounding rock respectively. Therefore, under the movable abutment pressure, the gateway deformation is serious. At the same time, the accumulated water on gateway floor must be drained in time. These measures were taken in the 1302 and 1304 coal faces in Gengcun colliery, and satisfactory results have been obtained. 8 refs., 3 figs.

The Other Kind of Rock: Diversifying Geosciences Outreach with some Tools from Rock n' Roll

Science.gov (United States)

Konecky, B. L.

2015-12-01

Music can communicate science at times when words and graphs fail. For this reason, earth scientists are increasingly using sounds and rhythms to capture the public's imagination while demonstrating technical concepts and sharing the societal impacts of their research. Musical approaches reach across the boundaries of perceptual learning style, age, gender, and life history. Music therefore makes science (and scientists) more approachable to a wide range of people. But in addition to its unique power for engaging diverse audiences, music-based outreach also sets an example for the geosciences' untapped potential as a public empowerment tool. Like many STEM fields, the music industry has long been criticized for poor inclusion of women and minorities. Rock n' roll camps for girls are answering this challenge by teaching music as a vessel for empowerment, with principles that can easily be adapted to geoscience outreach and education. The process of observing the planet is innately empowering; outreach programs that emphasize this in their design will take their impacts to the next level. Just as diversity in the scientific community benefits geoscience, geoscience also benefits diverse communities. This presentation will outline some principles and applications from the music world to achieving both of these aims.

Vegetation types, dominant compositions, woody plant diversity and stand structure in Trishna Wildlife Sanctuary of Northeast India.

Science.gov (United States)

Majumdar, Koushik; Datta, B K

2015-03-01

Present study was carried out to assess the vegetation types, diversity and phytosociological status of woody plants in Trishna Wildlife Sanctuary of Tripura, Northeast India. Vegetation data was derived by 25 line transects (10 m wide and 500 m length, each 0.5 ha size). All woody species at >10 cm gbh (Girth at Breast Height) within each plots were measured and counted. A total of six forest types were classified by cluster analysis using Importance Value Index (IVI) of 289 woody species. Species diversity, forest structure and woody community associations were evaluated and discussed. One way ANOVA revealed significant differences in all species diversity measures and stand structure along the forest types. Distribution of stem density at ten different gbh classes showed reverse J-shaped curves. Population status of woody plants was also examined through grouping of all individuals into four population age stages viz. sapling ( or = 30 - 120 - 210 cm gbh) and old (> or =210 cm). To observe dominant composition and species population trend, IVI of top ten dominant species from all forest types were tabulated. The present study suggested that Trishna Wildlife Sanctuary is an important habitat in Tripura from floristic point of view and it should be conserved on priority basis for remaining wildlife endurances and monitor for forest livelihoods products for sustainable biodiversity conservation in this region.

Capturing the Diversity in Lexical Diversity

Science.gov (United States)

Jarvis, Scott

2013-01-01

The range, variety, or diversity of words found in learners' language use is believed to reflect the complexity of their vocabulary knowledge as well as the level of their language proficiency. Many indices of lexical diversity have been proposed, most of which involve statistical relationships between types and tokens, and which ultimately…

For Those About to Rock : Naislaulajat rock-genressä

OpenAIRE

Herranen, Linda

2015-01-01

For those about to rock – naislaulajat rock-genressä antaa lukijalleen kokonaisvaltaisen käsityksen naisista rock-genressä: rockin historiasta, sukupuolittuneisuudesta, seksismistä, suomalaisten naislaulajien menestyksestä. Työn aineisto on koottu aihepiirin kirjallisuudesta ja alalla toimiville naislaulajille teetettyjen kyselyiden tuloksista. Lisäksi avaan omia kokemuksiani ja ajatuksiani, jotta näkökulma naisista rock-genressä tulisi esille mahdollisimman monipuolisesti. Ajatus aihees...

Stepwise Rock-Eval pyrolysis as a tool for typing heterogeneous organic matter in soils

Energy Technology Data Exchange (ETDEWEB)

Hetenyi, M.; Nyilas, T.; Toth, T.M. [Department of Mineralogy, Geochemistry and Petrology, University of Szeged, P.O. Box 651, H-6701 Szeged (Hungary)

2005-08-15

This paper presents an application of Rock-Eval pyrolysis for estimating the proportion of the components with different thermal stability in soil organic matter, the maturity of which corresponds to the early stage of diagenesis. For testing the validity of the modified Rock-Eval method, parallel series of pyrolysis were carried out on sedimentary rock samples. The temperature program was selected on the basis of the results obtained from stepwise Rock-Eval pyrolysis and from the mathematical deconvolution of pyrograms. The proportion of the original biomolecules in soil organic matter was calculated by the integration of pyrograms below 350{sup o}C and could be determined rapidly by one single pyrolysis using 350{sup o}C as initial cracking temperature. At 380{sup o}C, both the mathematical and the experimental methods provide reliable information about the proportion of the humic substances. Conversely, for rock samples, mathematical deconvolution of the pyrograms showed the heterogeneity of the sedimentary organic matter, the maturity of which corresponds to late diagenesis, without any estimation of the proportion of the different components. The rate of organic carbon accumulation in the studied soils and the decomposition rate of biopolymers were interpreted as a function of land-use and redox conditions. Differences in the precursor vegetation and in the environmental parameters resulted in markedly reduced carbon storage and higher degree of humification in the agricultural soil than in the adjacent forest soil. Redox conditions strongly affected both the amount and the elemental composition of the stored organic matter. The decomposition rate of biopolymers appeared to be controlled mainly by the contribution of resistant lignin components to the source biomass and, to a lesser extent, by redox conditions.

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Art Rocks with Rock Art!

Science.gov (United States)

Bickett, Marianne

2011-01-01

This article discusses rock art which was the very first "art." Rock art, such as the images created on the stone surfaces of the caves of Lascaux and Altimira, is the true origin of the canvas, paintbrush, and painting media. For there, within caverns deep in the earth, the first artists mixed animal fat, urine, and saliva with powdered minerals…

Uranium deposits in granitic rocks

International Nuclear Information System (INIS)

Nishimori, R.K.; Ragland, P.C.; Rogers, J.J.W.; Greenberg, J.K.

1977-01-01

This report is a review of published data bearing on the geology and origin of uranium deposits in granitic, pegmatitic and migmatitic rocks with the aim of assisting in the development of predictive criteria for the search for similar deposits in the U.S. Efforts were concentrated on the so-called ''porphyry'' uranium deposits. Two types of uranium deposits are primarily considered: deposits in pegmatites and alaskites in gneiss terrains, and disseminations of uranium in high-level granites. In Chapter 1 of this report, the general data on the distribution of uranium in igneous and metamorphic rocks are reviewed. Chapter 2 contains some comments on the classification of uranium deposits associated with igneous rocks and a summary of the main features of the geology of uranium deposits in granites. General concepts of the behavior of uranium in granites during crustal evolution are reviewed in Chapter 3. Also included is a discussion of the relationship of uranium mineralization in granites to the general evolution of mobile belts, plus the influence of magmatic and post-magmatic processes on the distribution of uranium in igneous rocks and related ore deposits. Chapter 4 relates the results of experimental studies on the crystallization of granites to some of the geologic features of uranium deposits in pegmatites and alaskites in high-grade metamorphic terrains. Potential or favorable areas for igneous uranium deposits in the U.S.A. are delineated in Chapter 5. Data on the geology of specific uranium deposits in granitic rocks are contained in Appendix 1. A compilation of igneous rock formations containing greater than 10 ppM uranium is included in Appendix 2. Appendix 3 is a report on the results of a visit to the Roessing area. Appendix 4 is a report on a field excursion to eastern Canada

Natural radionuclides in the rocks of the Valle del Cervo Pluton in Piedmont.

Science.gov (United States)

Sesana, Lucia; Fumagalli, Marco; Carnevale, Mauro; Polla, Giancarla; Facchini, Ugo; Colombo, Annita; Tunesi, Annalisa; De Capitani, Luisa; Rusconi, Rosella

2006-01-01

Monitoring of the gamma radiation in Valle del Cervo Pluton was performed by determining U and Th contents in the main rock types cropping out over the entire area and pertaining to the granitic complex, syenitic complex and monzonitic complex. In particular, syenitic rocks were largely used as building and ornamental materials (e.g. Sienite della Balma). All the samples are fresh and do not present joints or fractures filled with U minerals. In the crushed samples the activity of uranium varies from 346 to 764 Bq/kg. Concentration of thorium varies from 202 to 478 Bq/kg. For all the analysed rocks uranium activity is higher than thorium one. The lowest value of radioactive concentration is referred to rocks of the granitic complex. The most active rocks are syenites. The data confirm the high activities of Valle del Cervo rock types, strongly connected with high K content of the source magma (geochemical signature); on the contrary, the activity seems to be not related to the location of the samples.

Numerical simulation of rock cutting using 2D AUTODYN

International Nuclear Information System (INIS)

Woldemichael, D E; Rani, A M Abdul; Lemma, T A; Altaf, K

2015-01-01

In a drilling process for oil and gas exploration, understanding of the interaction between the cutting tool and the rock is important for optimization of the drilling process using polycrystalline diamond compact (PDC) cutters. In this study the finite element method in ANSYS AUTODYN-2D is used to simulate the dynamics of cutter rock interaction, rock failure, and fragmentation. A two-dimensional single PDC cutter and rock model were used to simulate the orthogonal cutting process and to investigate the effect of different parameters such as depth of cut, and back rake angle on two types of rocks (sandstone and limestone). In the simulation, the cutting tool was dragged against stationary rock at predetermined linear velocity and the depth of cut (1,2, and 3 mm) and the back rake angles(-10°, 0°, and +10°) were varied. The simulation result shows that the +10° back rake angle results in higher rate of penetration (ROP). Increasing depth of cut leads to higher ROP at the cost of higher cutting force. (paper)

Mineralogical and textural characteristics of Kakul (Hazara) phosphate rock, NWFP, Pakistan

International Nuclear Information System (INIS)

Mehmood, R.; Bhatti, M.A.; Kazmi, K.R.; Mehmood, A.; Sheikh, S.T.; Aleem Shah, S.A.

2010-01-01

Various types of minerals, present in phosphate rock of Hazara area of Khyber Pukhtoonkhwa Province of Pakistan, were identified and their concentration was determined using a suitable method. The characteristics of the rock were defined by petrography, X-ray diffraction, and chemical analysis and the textural characteristics such as grain size, grain shape and their arrangement in the rock body were also investigated. The degree of liberation of phosphate-bearing mineral was studied by the particle-counting method. Mineralogical and textural observations indicated that fine-grained rock may be suitable for beneficiation by the froth flotation separation technique. (author)

Fractures and Rock Mechanics, Phase 1

DEFF Research Database (Denmark)

Krogsbøll, Anette; Jakobsen, Finn; Madsen, Lena

1997-01-01

The main objective of the project is to combine geological descriptions of fractures, chalk types and rock mechanical properties in order to investigate whether the chosen outcrops can be used as analogues to reservoir chalks. This report deals with 1) geological descriptions of outcrop locality...

Investigation of trace uranium content in rock phosphate ore samples from Kurun-Uro area, Nuba Mountains, Sudan

International Nuclear Information System (INIS)

Ali, Abdel Majid Abdel Galil Mohammed

1999-07-01

This investigation was carried out mainly to test the trace uranium level content in rock phosphate, which was used as a low cost fertilizer. Two types of rock phosphate were examined, namely, Kurun and Uro rocks from Nuba Mountains in the Southern Kurdufan province, Sudan.This area has a high background natural radioactivity. Moreover, it contains a rock phosphate zone lying between J. Kurun and Uro. The work included analytical methods carried out for thr rock phosphate samples using spectrophotometric and X-ray fluorescence techniques. The results obtained were compared with the data from literature and they showed a good agreement.The data was statistically analyzed to compare the results by the two techniques. The results of uranium content determined by the two analytical methods were significantly similar.The instrumental analysis revealed that different. Uranium content in the rocks phosphate samples of Uro type was found to be 1.6 times higher than Kurun type. (Author)

Steady as a rock: Biogeomorphic influence of nurse rocks and slope processes on kūpaoa (Dubautia menziesii) shrubs in Haleakalā Crater (Maui, Hawai'i)

Science.gov (United States)

Pérez, Francisco L.

2017-10-01

This study examines biogeomorphic interactions between nurse rocks, slope processes, and 300 kūpaoa (Dubautia menziesii) shrubs in Haleakalā Crater (Maui, Hawai'i). Research objectives were to: assess the association of kūpaoa with substrates upslope and downslope of plants, and proximity to the closest rock uphill; contrast shrub/substrate relationships with site frequency of sediment types; measure surface soil shear-strength and compressibility on 50 paired locations near boulders; and investigate the aggregation characteristics and spatial patterns of kūpaoa in relation to rock and substrate variation. Data analyzed came from three 100-plant surveys at 3 sites: a plant census at 2720-2975 m altitude, and wandering-quarter transects (WQTs) across two areas (2610-2710 m); ground sediment cover was estimated along four phototransects on these sites. Data for the three 100-plant surveys included substrate type-outcrops, blocks, cobbles, pebbles, exposed soil, organic litter-upslope from each plant, and distance to the largest rock upslope. The two surveys examined along WQTs included substrate type found downslope from kūpaoa, plant height, plant diameters across and along the slope, and distance between successively censused plants. Most plants grew downslope of nurse rocks; > 74% were adjacent to blocks or outcrops, and > 17% near cobbles. Plants showed avoidance for finer substrates; only 5.3% and 2.7% grew on/near bare soils and pebbles, respectively. About 92% of kūpaoa were ≤ 10 cm downslope of rocks; > 89% grew ≤ 2 cm away, and 83% in direct contact with a rock. Some seedlings also grew on pukiawe (Leptecophylla tameiameiae) nurse plants. Several stable rock microsites protected plants from disturbance by slope processes causing debris shift. Site sediments were significantly finer than substrates near plants; shrubs grew preferentially adjacent to boulders > 20 cm wide, which were more common near plants than across sites. Soils downslope of 50

Magnetite-apatite-dolomitic rocks of Ust-Chulman (Aldan shield, Russia): Seligdar-type carbonatites?

Science.gov (United States)

Prokopyev, Ilya R.; Doroshkevich, Anna G.; Redina, Anna A.; Obukhov, Andrey V.

2018-04-01

The Ust-Chulman apatite ore body is situated within the Nimnyrskaya apatite zone at the Aldan shield in Russia. The latest data confirm the carbonatitic origin of the Seligdar apatite deposit (Prokopyev et al. in Ore Geol Rev 81:296-308, 2017). The results of our investigations demonstrate that the magnetite-apatite-dolomitic rocks of the Ust-Chulman are highly similar to Seligdar-type dolomitic carbonatites in terms of the mineralogy and the fluid regime of formation. The ilmenite and spinel mineral phases occur as solid solutions with magnetite, and support the magmatic origin of the Ust-Chulman ores. The chemical composition of REE- and SO3-bearing apatite crystals and, specifically, monazite-(Ce) mineralisation and the formation of Nb-rutile, late hydrothermal sulphate minerals (barite, anhydrite) and haematite are typical for carbonatite complexes. The fluid inclusions study revealed similarities to the evolutionary trend of the Seligdar carbonatites that included changes of the hydrothermal solutions from highly concentrated chloride to medium-low concentrated chloride-sulphate and oxidized carbonate-ferrous.

Tungsten abundances in some volcanic rocks

International Nuclear Information System (INIS)

Helsen, J.N.; Shaw, D.M.; Crocket, J.H.

1978-01-01

A radiochemical N.A.A. method was used to obtain new values on W distribution in some 125 volcanic rocks, mainly basalts and andesites, from different petrotectonic environments. These W data are below previously reported abundances. New median values in various types of rocks are suggested (ppm W). Basalts: ocean floor, 0.15; ocean islands subalkaline, 0.28; ocean islands alkaline, 0.60; island arc, 0.19; continental margin, 0.40; continental subalkaline, 0.30; continental alkaline, 1.35. Andesites: island arc, 0.23; continental margin, 1.05. Median values for all 91 basalts and all 20 andesites are 0.36 and 0.29 ppm respectively. (author)

Rock support for nuclear waste repositories

International Nuclear Information System (INIS)

Abramson, L.W.; Schmidt, B.

1984-01-01

The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be designed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support

Prediction of tunnel boring machine performance using machine and rock mass data

International Nuclear Information System (INIS)

Dastgir, G.

2012-01-01

Performance of the tunnel boring machine and its prediction by different methods has been a hot issue since the first TBM came into being. For the sake of safe and sound transport, improvement of hydro-power, mining, civil and many other tunneling projects that cannot be driven efficiently and economically by conventional drill and blast, TBMs are quite frequently used. TBM parameters and rock mass properties, which heavily influence machine performance, should be estimated or known before choice of TBM-type and start of excavation. By applying linear regression analysis (SPSS19), fuzzy logic tools and a special Math-Lab code on actual field data collected from seven TBM driven tunnels (Hieflau expansion, Queen water tunnel, Vereina, Hemerwald, Maen, Pieve and Varzo tunnel), an attempt was made to provide prediction of rock mass class (RMC), rock fracture class (RFC), penetration rate (PR) and advance rate (AR). For detailed analysis of TBM performance, machine parameters (thrust, machine rpm, torque, power etc.), machine types and specification and rock mass properties (UCS, discontinuity in rock mass, RMC, RFC, RMR, etc.) were analyzed by 3-D surface plotting using statistical software R. Correlations between machine parameters and rock mass properties which effectively influence prediction models, are presented as well. In Hieflau expansion tunnel AR linearly decreases with increase of thrust due to high dependence of machine advance rate upon rock strength. For Hieflau expansion tunnel three types of data (TBM, rock mass and seismic data e.g. amplitude, pseudo velocity etc.) were coupled and simultaneously analyzed by plotting 3-D surfaces. No appreciable correlation between seismic data (Amplitude and Pseudo velocity) and rock mass properties and machine parameters could be found. Tool wear as a function of TBM operational parameters was analyzed which revealed that tool wear is minimum if applied thrust is moderate and that tool wear is high when thrust is

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

from bituminite-fair to bituminite-rich and to higher percentages of visible organic matter towards the younger interval. These differences in the organic matter type are attributed to i) early diagenetic kerogen sulfurization and ii) the upwelling depositional environment. Moreover, kerogen sulfurization was controlled by the relationship between carbonate, iron and sulfur as well as the organic matter. Thus, the organic carbon-rich deposits can be grouped into: i) low Sorg and moderately organic matter-rich oil prone source rocks, ii) moderate Sorg and organic-carbon-rich oil prone source rocks, iii) high Sorg and organic carbon-rich oil prone source rocks and iv) very high Sorg and organic carbon-rich oil prone source rocks, the latter representing the CTBE interval. Types 2 to 4 will generate sulfur-rich petroleum upon maturation or artificial oil shale retorting. This integrated organic and inorganic approach sheds light on the various processes leading to the development of the world-class oil shales deposited through the Cenomanian to Turonian. In addition, this study shows how the changes in the depositional environment might have controlled kerogen sulfurization and organic matter preservation and structure. This detailed approach provides a better understanding on source rock development during the Cenomanian to Turonian in a global context, as many of the geochemical features were identified worldwide for deposits related to OAE2. (Author)

Development of soda-lime glasses from ornamental rock wastes

International Nuclear Information System (INIS)

Babisk, Michelle Pereira

2009-01-01

During the ornamental rocks production, among other steps, one saw the rock blocks in order to transform them into semi-finished plates. In this step, expressive amounts of residues are generated, which are not properly discharged in nature, without any programmed utilization. The residues of silicide rocks present, in their compositions, oxides which are raw materials employed to fabricate soda-lime type glasses (containing SiO_2, Al_2O_3, CaO, Na_2O and K_2O). On the other hand the residues of carbonatic rocks are constituted of glass net modifier oxides, like CaO and MgO. In this work it was developed four types of soda-lime glasses using ornamental rock residues, where the glasses compositions were adjusted by adding sand, as silica source, as well as sodium and calcium carbonates as sources of Na_2O and CaO, respectively. The obtained glasses were characterized by means of Archimed's method for densities measurements, microstructure by using optical and electronic microscopy, phases by means of X-ray diffraction (XRD), hardness by Vickers indentation, spectroscopy (UV/VIS), and hydrolytic resistance according to ISO 719. The XRD analyses confirmed the compositions total vitrification, where the greened aspect of the samples was due to the presence of the iron oxides. The produced glasses properties were compared with those of commercial glasses aiming their industrial employment. The main difference between the produced glasses and those commercials varied primarily regarding the amount of carbonates incorporated. The results showed that the ornamental rocks residues may be used as raw materials for glasses fabrication, and they found a useful economic destination rather than discharge which promotes undesirable environmental impact. (author)

Using microsatellite markers to analyze genetic diversity in 14 sheep types in Iran

Directory of Open Access Journals (Sweden)

M. T. Vajed Ebrahimi

2017-07-01

Full Text Available Investigation of genetic relationship among populations has been traditionally based on the analysis of allele frequencies at different loci. The prime objective of this research was to measure the genetic polymorphism of five microsatellite markers (McMA2, BM6444, McMA26, HSC, and OarHH35 and study genetic diversity of 14 sheep types in Iran. Genomic DNA was extracted from blood samples of 565 individuals using an optimized salting-out DNA extraction procedure. The polymerase chain reaction (PCR was successfully performed with the specific primers. Some locus–population combinations were not at Hardy–Weinberg equilibrium (P < 0. 05. The microsatellite analysis revealed high allelic and gene diversity in all 14 breeds. Pakistani and Arabi breeds showed the highest mean number of alleles (11.8 and 11 respectively, while the highest value for polymorphic information content was observed for the Arabi breed (0.88. A UPGMA (unweighted pair group method with arithmetic mean dendrogram based on the Nei's standard genetic distance among studied breeds showed a separate cluster for Arabi and Pakistani breeds and another cluster for other breeds. The Shannon index (H0 for McMA2, BM6444, McMA26, HSC, and OarHH35 was 2.31, 2.17, 2.27, 2.04 and 2.18, respectively, and polymorphic information content (PIC values were 0.88, 0.92, 0.87, 0.84, and 0.86 for McMA2, BM6444, McMA26, HSC, and OarHH35, respectively. The high degree of variability demonstrated within the studied sheep types implies that these populations are rich reservoirs of genetic diversity that must be preserved.

Rock Art

Science.gov (United States)

Henn, Cynthia A.

2004-01-01

There are many interpretations for the symbols that are seen in rock art, but no decoding key has ever been discovered. This article describes one classroom's experiences with a lesson on rock art--making their rock art and developing their own personal symbols. This lesson allowed for creativity, while giving an opportunity for integration…

What does "Diversity" Mean for Public Engagement in Science? A New Metric for Innovation Ecosystem Diversity.

Science.gov (United States)

Özdemir, Vural; Springer, Simon

2018-03-01

Diversity is increasingly at stake in early 21st century. Diversity is often conceptualized across ethnicity, gender, socioeconomic status, sexual preference, and professional credentials, among other categories of difference. These are important and relevant considerations and yet, they are incomplete. Diversity also rests in the way we frame questions long before answers are sought. Such diversity in the framing (epistemology) of scientific and societal questions is important for they influence the types of data, results, and impacts produced by research. Errors in the framing of a research question, whether in technical science or social science, are known as type III errors, as opposed to the better known type I (false positives) and type II errors (false negatives). Kimball defined "error of the third kind" as giving the right answer to the wrong problem. Raiffa described the type III error as correctly solving the wrong problem. Type III errors are upstream or design flaws, often driven by unchecked human values and power, and can adversely impact an entire innovation ecosystem, waste money, time, careers, and precious resources by focusing on the wrong or incorrectly framed question and hypothesis. Decades may pass while technology experts, scientists, social scientists, funding agencies and management consultants continue to tackle questions that suffer from type III errors. We propose a new diversity metric, the Frame Diversity Index (FDI), based on the hitherto neglected diversities in knowledge framing. The FDI would be positively correlated with epistemological diversity and technological democracy, and inversely correlated with prevalence of type III errors in innovation ecosystems, consortia, and knowledge networks. We suggest that the FDI can usefully measure (and prevent) type III error risks in innovation ecosystems, and help broaden the concepts and practices of diversity and inclusion in science, technology, innovation and society.

Uranium migration and retention during weathering of a granitic waste rock pile

International Nuclear Information System (INIS)

Boekhout, F.; Gérard, M.; Kanzari, A.; Michel, A.; Déjeant, A.; Galoisy, L.; Calas, G.; Descostes, M.

2015-01-01

Highlights: • We investigate the environmental impact of the granitic waste rock piles. • The majority of the waste rocks in the pile is barren- or overburden rock. • The main neo-formed U-bearing phases are (Ca) and (Cu) uranyl phosphates. • Under circum-neutral pH conditions they do not pose an environment threat. - Abstract: This study investigates the post-mining evolution of S-type granitic waste rocks around a former uranium mine, Vieilles Sagnes (Haute Vienne, NW Massif Central, France). This mine was operated between 1957 and 1965 in the La Crouzille former world-class uranium mining district and is representative of intra-granitic vein-type deposits. 50 years after mine closure and the construction and subsequent re-vegetation of the granitic waste rock pile, we evaluate the environmental evolution of the rock pile, including rock alteration, neo-formation of U-bearing phases during weathering, and U migration. Vertical trenches have been excavated through the rock pile down to an underlying paleo-soil, allowing the investigation of the vertical differentiation of the rock pile and its influence on water pathways, weathering processes and U migration and retention. Arenization dominantly drives liberation of U, by dissolution of uraninite inclusions in the most alterable granitic minerals (i.e. K-feldspar and biotite). Retention of U in the matrix at the base of the waste rock pile, and in the underlying paleo-soil most likely occurs by precipitation of (nano-) uranyl phosphates or a combination of co-precipitation and adsorption reactions of U onto Fe (oxy)hydroxides and/or clay minerals. Even though U-migration was observed, U is retained in stable secondary mineral phases, provided the current conditions will not be modified

Characteristics of mesozoic magmatic rocks in western Zhejiang and their relation with uranium mineralization

International Nuclear Information System (INIS)

Zhou Jiazhi

2000-01-01

The author summarizes characteristics of Mesozoic (Yangshanian Period) acid-intermediate volcanics, sub-volcanics and basic intrusive from aspects of formation time of rock series, petrogenic sequence, chemical composition, rock -controlling factors and petrogenic environments. It is suggested that these rocks were originated from different source areas of crust and mantle. Based on the time-space relation between different types uranium deposits and magmatic rocks, the author proposes that: the earlier stage (Earlier Cretaceous) U-hematite ores were originated from acid volcanic magmatism of crustal source, but the later stage (Late Cretaceous) pitchblende-polymetallic sulfide and pitchblende-purple fluorite rich ores were derived from basic magmatism of mantle source. Finally, the author proposes prospecting criteria of the above two types of uranium deposits

Geophagy (rock eating, experimental stress and cognitive idiosyncrasy

Directory of Open Access Journals (Sweden)

Kirill Golokhvast

2014-05-01

Conclusions: These results suggest that, in natural environmental conditions, “edible” rocks serve as an adaptive tool for recovery from various types of environmental stresses, and are examples of self-medication.

Microbial colonisation in diverse surface soil types in Surtsey and diversity analysis of its subsurface microbiota

Science.gov (United States)

Marteinsson, V.; Klonowski, A.; Reynisson, E.; Vannier, P.; Sigurdsson, B. D.; Ólafsson, M.

2014-09-01

Colonisation of life on Surtsey has been observed systematically since the formation of the island 50 years ago. Although the first colonisers were prokaryotes, such as bacteria and blue-green algae, most studies have been focusing on settlement of plants and animals but less on microbial succession. To explore microbial colonization in diverse soils and the influence of associate vegetation and birds on numbers of environmental bacteria, we collected 45 samples from different soils types on the surface of the island. Total viable bacterial counts were performed with plate count at 22, 30 and 37 °C for all soils samples and the amount of organic matter and nitrogen (N) was measured. Selected samples were also tested for coliforms, faecal coliforms aerobic and anaerobic bacteria. The deep subsurface biosphere was investigated by collecting liquid subsurface samples from a 182 m borehole with a special sampler. Diversity analysis of uncultivated biota in samples was performed by 16S rRNA gene sequences analysis and cultivation. Correlation was observed between N deficits and the number of microorganisms in surface soils samples. The lowest number of bacteria (1 × 104-1 × 105 g-1) was detected in almost pure pumice but the count was significant higher (1 × 106-1 × 109 g-1) in vegetated soil or pumice with bird droppings. The number of faecal bacteria correlated also to the total number of bacteria and type of soil. Bacteria belonging to Enterobacteriaceae were only detected in vegetated and samples containing bird droppings. The human pathogens Salmonella, Campylobacter and Listeria were not in any sample. Both thermophilic bacteria and archaea 16S rDNA sequences were found in the subsurface samples collected at 145 m and 172 m depth at 80 °C and 54 °C, respectively, but no growth was observed in enrichments. The microbiota sequences generally showed low affiliation to any known 16S rRNA gene sequences.

Microbial colonization in diverse surface soil types in Surtsey and diversity analysis of its subsurface microbiota

Science.gov (United States)

Marteinsson, V.; Klonowski, A.; Reynisson, E.; Vannier, P.; Sigurdsson, B. D.; Ólafsson, M.

2015-02-01

Colonization of life on Surtsey has been observed systematically since the formation of the island 50 years ago. Although the first colonisers were prokaryotes, such as bacteria and blue-green algae, most studies have been focused on the settlement of plants and animals but less on microbial succession. To explore microbial colonization in diverse soils and the influence of associated vegetation and birds on numbers of environmental bacteria, we collected 45 samples from different soil types on the surface of the island. Total viable bacterial counts were performed with the plate count method at 22, 30 and 37 °C for all soil samples, and the amount of organic matter and nitrogen (N) was measured. Selected samples were also tested for coliforms, faecal coliforms and aerobic and anaerobic bacteria. The subsurface biosphere was investigated by collecting liquid subsurface samples from a 181 m borehole with a special sampler. Diversity analysis of uncultivated biota in samples was performed by 16S rRNA gene sequences analysis and cultivation. Correlation was observed between nutrient deficits and the number of microorganisms in surface soil samples. The lowest number of bacteria (1 × 104-1 × 105 cells g-1) was detected in almost pure pumice but the count was significantly higher (1 × 106-1 × 109 cells g-1) in vegetated soil or pumice with bird droppings. The number of faecal bacteria correlated also to the total number of bacteria and type of soil. Bacteria belonging to Enterobacteriaceae were only detected in vegetated samples and samples containing bird droppings. The human pathogens Salmonella, Campylobacter and Listeria were not in any sample. Both thermophilic bacteria and archaea 16S rDNA sequences were found in the subsurface samples collected at 145 and 172 m depth at 80 and 54 °C, respectively, but no growth was observed in enrichments. The microbiota sequences generally showed low affiliation to any known 16S rRNA gene sequences.

Musical Structure as Narrative in Rock

Directory of Open Access Journals (Sweden)

John Fernando Encarnacao

2011-09-01

Full Text Available In an attempt to take a fresh look at the analysis of form in rock music, this paper uses Susan McClary’s (2000 idea of ‘quest narrative’ in Western art music as a starting point. While much pop and rock adheres to the basic structure of the establishment of a home territory, episodes or adventures away, and then a return, my study suggests three categories of rock music form that provide alternatives to common combinations of verses, choruses and bridges through which the quest narrative is delivered. Labyrinth forms present more than the usual number of sections to confound our sense of ‘home’, and consequently of ‘quest’. Single-cell forms use repetition to suggest either a kind of stasis or to disrupt our expectations of beginning, middle and end. Immersive forms blur sectional divisions and invite more sensual and participatory responses to the recorded text. With regard to all of these alternative approaches to structure, Judy Lochhead’s (1992 concept of ‘forming’ is called upon to underline rock music forms that unfold as process, rather than map received formal constructs. Central to the argument are a couple of crucial definitions. Following Theodore Gracyk (1996, it is not songs, as such, but particular recordings that constitute rock music texts. Additionally, narrative is understood not in (direct relation to the lyrics of a song, nor in terms of artists’ biographies or the trajectories of musical styles, but considered in terms of musical structure. It is hoped that this outline of non-narrative musical structures in rock may have applications not only to other types of music, but to other time-based art forms.

Characterization of rock samples localized in some sites of the Mexican Pacific coast

International Nuclear Information System (INIS)

Pena, P.; Torre, J. de la; Falcon, T.; Segovia, N.; Azorin, J.

1999-01-01

Geophysical studies in zones of high seismicity have showed differences in the content of radioactive material that is used in the study of the geochemical behavior of the subsoil. In an emanometric mapping of radon in soil realized in the Mexican Pacific coast were finding distinct levels in zones with different lithology. With the finality to know the mineralization types in two zones of study which are localized in the Guerrero coast and they belonging to terrains named Guerrero and Xolapa it was determined the mineralogic characteristics in two types of rocks. The identification of the rocks was realized by X-ray diffraction and was determined the elemental chemical composition using a scanning electron microscope. It was indicated in the results obtained that in the two types of rocks were found minerals such as: quartz, albite, microcline anortite, ferroactinolite and biotite. However, it was found differences between them by the presence of their mineralogic compounds because in the rock belonging to Xolapa terrain were presented whereas in the rock localized in the Guerrero terrain were presented sodic and potassic feldspars. The analysis by the Elemental Chemical Composition technique (Energy Dispersive Spectroscopy) corroborated the results obtained by the X-ray diffraction technique. (Author)

Dissecting the roles of ROCK isoforms in stress-induced cell detachment.

Science.gov (United States)

Shi, Jianjian; Surma, Michelle; Zhang, Lumin; Wei, Lei

2013-05-15

The homologous Rho kinases, ROCK1 and ROCK2, are involved in stress fiber assembly and cell adhesion and are assumed to be functionally redundant. Using mouse embryonic fibroblasts (MEFs) derived from ROCK1(-/-) and ROCK2(-/-) mice, we have recently reported that they play different roles in regulating doxorubicin-induced stress fiber disassembly and cell detachment: ROCK1 is involved in destabilizing the actin cytoskeleton and cell detachment, whereas ROCK2 is required for stabilizing the actin cytoskeleton and cell adhesion. Here, we present additional insights into the roles of ROCK1 and ROCK2 in regulating stress-induced impairment of cell-matrix and cell-cell adhesion. In response to doxorubicin, ROCK1(-/-) MEFs showed significant preservation of both focal adhesions and adherens junctions, while ROCK2(-/-) MEFs exhibited impaired focal adhesions but preserved adherens junctions compared with the wild-type MEFs. Additionally, inhibition of focal adhesion or adherens junction formations by chemical inhibitors abolished the anti-detachment effects of ROCK1 deletion. Finally, ROCK1(-/-) MEFs, but not ROCK2(-/-) MEFs, also exhibited preserved central stress fibers and reduced cell detachment in response to serum starvation. These results add new insights into a novel mechanism underlying the anti-detachment effects of ROCK1 deletion mediated by reduced peripheral actomyosin contraction and increased actin stabilization to promote cell-cell and cell-matrix adhesion. Our studies further support the differential roles of ROCK isoforms in regulating stress-induced loss of central stress fibers and focal adhesions as well as cell detachment.

Restoration of Circum-Arctic Upper Jurassic source rock paleolatitude based on crude oil geochemistry

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.

2008-01-01

Tectonic geochemical paleolatitude (TGP) models were developed to predict the paleolatitude of petroleum source rock from the geochemical composition of crude oil. The results validate studies designed to reconstruct ancient source rock depositional environments using oil chemistry and tectonic reconstruction of paleogeography from coordinates of the present day collection site. TGP models can also be used to corroborate tectonic paleolatitude in cases where the predicted paleogeography conflicts with the depositional setting predicted by the oil chemistry, or to predict paleolatitude when the present day collection locality is far removed from the source rock, as might occur due to long distance subsurface migration or transport of tarballs by ocean currents. Biomarker and stable carbon isotope ratios were measured for 496 crude oil samples inferred to originate from Upper Jurassic source rock in West Siberia, the North Sea and offshore Labrador. First, a unique, multi-tiered chemometric (multivariate statistics) decision tree was used to classify these samples into seven oil families and infer the type of organic matter, lithology and depositional environment of each organofacies of source rock [Peters, K.E., Ramos, L.S., Zumberge, J.E., Valin, Z.C., Scotese, C.R., Gautier, D.L., 2007. Circum-Arctic petroleum systems identified using decision-tree chemometrics. American Association of Petroleum Geologists Bulletin 91, 877-913]. Second, present day geographic locations for each sample were used to restore the tectonic paleolatitude of the source rock during Late Jurassic time (???150 Ma). Third, partial least squares regression (PLSR) was used to construct linear TGP models that relate tectonic and geochemical paleolatitude, where the latter is based on 19 source-related biomarker and isotope ratios for each oil family. The TGP models were calibrated using 70% of the samples in each family and the remaining 30% of samples were used for model validation. Positive

New Rock Abrasivity Test Method for Tool Life Assessments on Hard Rock Tunnel Boring: The Rolling Indentation Abrasion Test (RIAT)

Science.gov (United States)

Macias, F. J.; Dahl, F.; Bruland, A.

2016-05-01

The tunnel boring machine (TBM) method has become widely used and is currently an important presence within the tunnelling industry. Large investments and high geological risk are involved using TBMs, and disc cutter consumption has a great influence on performance and cost, especially in hard rock conditions. Furthermore, reliable cutter life assessments facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory tests for rock abrasivity assessments are needed. A new abrasivity test method by rolling disc named Rolling Indentation Abrasion Test (RIAT) has been developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than the traditionally used methods. Wear by rolling contact on intact rock samples is introduced and several rock types, covering a wide rock abrasiveness range, have been tested by RIAT. The RIAT procedure indicates a great ability of the testing method to assess abrasive wear on rolling discs. In addition and to evaluate the newly developed RIAT test method, a comprehensive laboratory testing programme including the most commonly used abrasivity test methods and the mineral composition were carried out. Relationships between the achieved results from conventional testing and RIAT results have been analysed.

K-Ar age for alunite-bearing rock from the Iwato gold deposit, Kagoshima Prefecture, southern Japan

International Nuclear Information System (INIS)

Togashi, Yukio; Shibata, Ken

1984-01-01

K-Ar age determination was made on a whole rock sample of the alunite-bearing silicified rock from the Iwato gold deposit, Kagoshima Prefecture, southern Japan. The sample is from one of the Nansatsu-type gold deposits, whose mineralization is characterized by the occurrence of leaching-type massive silicified rocks with gold dissemination. The result, 4.15 +- 0.78 Ma, is interpreted to be the age of the mineralization at the Iwato gold deposit. It also suggests that the Nansatsu-type deposits were formed in close association with andesitic volcanism in the early Pliocene age. (author)

Characterizing the hypersiliceous rocks of Belgium used in (pre-)history: a case study on sourcing sedimentary quartzites

International Nuclear Information System (INIS)

Veldeman, Isis; Baele, Jean-Marc; De Doncker, H W J A; Goemaere, Eric; Deceukelaire, Marleen; Dusar, Michiel

2012-01-01

Tracking raw material back to its extraction source is a crucial step for archaeologists when trying to deduce migration patterns and trade contacts in (pre-)history. Regarding stone artefacts, the main rock types encountered in the archaeological record of Belgium are hypersiliceous rocks. This is a newly introduced category of rock types comprising those rocks made of at least 90% silica. These are strongly silicified quartz sands or sedimentary quartzites, siliceous rocks of chemical and biochemical origin (e.g. flint), very pure metamorphic quartzites and siliceous volcanic rocks (e.g. obsidian). To be able to distinguish between different extraction sources, ongoing research was started to locate possible extraction sources of hypersiliceous rocks and to characterize rocks collected from these sources. Characterization of these hypersiliceous rocks is executed with the aid of optical polarizing microscopy, optical cold cathodoluminescence and scanning-electron microscopy combined with energy-dispersive x-ray spectrometry and with back-scatter electron imaging. In this paper, we focus on various sedimentary quartzites of Paleogene stratigraphical level. (paper)

Comparison of disposal concepts for rock salt and hard rock

International Nuclear Information System (INIS)

Papp, R.

1998-01-01

The study was carried out in the period 1994-1996. The goals were to prepare a draft on spent fuel disposal in hard rock and additionally a comparison with existing disposal concepts for rock salt. A cask for direct disposal of spent fuel and a repository for hard rock including a safeguards concept were conceptually designed. The results of the study confirm, that the early German decision to employ rock salt was reasonable. (orig.)

Improved Genome Assembly and Annotation for the Rock Pigeon (Columba livia).

Science.gov (United States)

Holt, Carson; Campbell, Michael; Keays, David A; Edelman, Nathaniel; Kapusta, Aurélie; Maclary, Emily; T Domyan, Eric; Suh, Alexander; Warren, Wesley C; Yandell, Mark; Gilbert, M Thomas P; Shapiro, Michael D

2018-05-04

The domestic rock pigeon ( Columba livia ) is among the most widely distributed and phenotypically diverse avian species. C. livia is broadly studied in ecology, genetics, physiology, behavior, and evolutionary biology, and has recently emerged as a model for understanding the molecular basis of anatomical diversity, the magnetic sense, and other key aspects of avian biology. Here we report an update to the C. livia genome reference assembly and gene annotation dataset. Greatly increased scaffold lengths in the updated reference assembly, along with an updated annotation set, provide improved tools for evolutionary and functional genetic studies of the pigeon, and for comparative avian genomics in general. Copyright © 2018 Holt et al.

Frictional sliding tests on combined coal-rock samples

Directory of Open Access Journals (Sweden)

Tao Wang

2014-06-01

Full Text Available A test system was developed to understand the sliding mechanism of coal-rock structure. The test system was composed by a double-shear testing model and an acousto-optic monitoring system in association with a digital camera and an acoustic emission (AE instrument. The tests can simulate the movement of activated faults and the sliding in coal-rock structure. In this regard, instable sliding conditions of coal-rock samples, sliding types under different conditions, displacement evolution law, and AE characteristics during sliding process were investigated. Several sliding types were monitored in the tests, including unstable continuous sliding, unstable discontinuous sliding, and stable sliding. The sliding types have close relation with the axial loads and loading rates. Larger axial load and smaller loading rate mean that unstable sliding is less likely to occur. The peak shear stress was positively correlated with the axial load when sliding occurred, whereas the displacement induced by unstable sliding was uncorrelated with the axial load. A large number of AE events occurred before sliding, and the AE rate decreased after stable sliding. The results show that the tests can well simulate the process of structural instability in a coal bump, and are helpful in the understanding of fault activation and the physical processes during squeezing process of roof and floor.

Mechanism of Rock Burst Occurrence in Specially Thick Coal Seam with Rock Parting

Science.gov (United States)

Wang, Jian-chao; Jiang, Fu-xing; Meng, Xiang-jun; Wang, Xu-you; Zhu, Si-tao; Feng, Yu

2016-05-01

Specially thick coal seam with complex construction, such as rock parting and alternative soft and hard coal, is called specially thick coal seam with rock parting (STCSRP), which easily leads to rock burst during mining. Based on the stress distribution of rock parting zone, this study investigated the mechanism, engineering discriminant conditions, prevention methods, and risk evaluation method of rock burst occurrence in STCSRP through setting up a mechanical model. The main conclusions of this study are as follows. (1) When the mining face moves closer to the rock parting zone, the original non-uniform stress of the rock parting zone and the advancing stress of the mining face are combined to intensify gradually the shearing action of coal near the mining face. When the shearing action reaches a certain degree, rock burst easily occurs near the mining face. (2) Rock burst occurrence in STCSRP is positively associated with mining depth, advancing stress concentration factor of the mining face, thickness of rock parting, bursting liability of coal, thickness ratio of rock parting to coal seam, and difference of elastic modulus between rock parting and coal, whereas negatively associated with shear strength. (3) Technologies of large-diameter drilling, coal seam water injection, and deep hole blasting can reduce advancing stress concentration factor, thickness of rock parting, and difference of elastic modulus between rock parting and coal to lower the risk of rock burst in STCSRP. (4) The research result was applied to evaluate and control the risk of rock burst occurrence in STCSRP.

Soil ecology of a rock outcrop ecosystem: Abiotic stresses, soil respiration, and microbial community profiles in limestone cedar glades

Science.gov (United States)

Cartwright, Jennifer M.; Advised by Dzantor, E. Kudjo

2015-01-01

Limestone cedar glades are a type of rock outcrop ecosystem characterized by shallow soil and extreme hydrologic conditions—seasonally ranging from xeric to saturated—that support a number of plant species of conservation concern. Although a rich botanical literature exists on cedar glades, soil biochemical processes and the ecology of soil microbial communities in limestone cedar glades have largely been ignored. This investigation documents the abiotic stress regime of this ecosystem (shallow soil, extreme hydrologic fluctuations and seasonally high soil surface temperatures) as well as soil physical and chemical characteristics, and relates both types of information to ecological structures and functions including vegetation, soil respiration, and soil microbial community metabolic profiles and diversity. Methods used in this investigation include field observations and measurements of soil physical and chemical properties and processes, laboratory analyses, and microbiological assays of soil samples.

Characterization of type and genetic diversity among soybean cyst nematode differentiators

Directory of Open Access Journals (Sweden)

Éder Matsuo

2012-04-01

Full Text Available The development of soybean cyst nematode, Heterodera glycines Ichinohe, resistant genotypes with high yields has been one of the objectives of soybean (Glycine max (L. Merrill breeding programs. The objective of this study was to characterize the pathotype of soybean cyst nematodes and analyze the genetic diversity of ten differentiator lines ('Lee 74', Peking, Pickett, PI 88788, PI 90763, PI 437654, PI 209332, PI 89772, PI 548316 and 'Hartwig'. Inoculum was obtained from plants cultivated in field soil in Viçosa, state of Minas Gerais, Brazil. Thirty-four days after inoculating each plant with 4,000 eggs, the number of females, female index, total number of eggs, number of eggs per female, reproduction factor, plant height, number of nodes, fresh and dry matter weights were assessed. The differential lines were first grouped with Scott-Knott test. Subsequently, the genetic diversity was evaluated using dendrograms, graphic analysis and the Tocher grouping method. The inoculum of H. glycines obtained from NBSGBP-UFV was characterized as HG Type 0. The differentiating lines were divergent, and PI 89772, PI 437654, 'Hartwig' and 'Peking' had the greatest potential for use in breeding programs.

Rollerjaw Rock Crusher

Science.gov (United States)

Peters, Gregory; Brown, Kyle; Fuerstenau, Stephen

2009-01-01

The rollerjaw rock crusher melds the concepts of jaw crushing and roll crushing long employed in the mining and rock-crushing industries. Rollerjaw rock crushers have been proposed for inclusion in geological exploration missions on Mars, where they would be used to pulverize rock samples into powders in the tens of micrometer particle size range required for analysis by scientific instruments.

Range sections as rock models for intensity rock scene segmentation

CSIR Research Space (South Africa)

Mkwelo, S

2007-11-01

Full Text Available This paper presents another approach to segmenting a scene of rocks on a conveyor belt for the purposes of measuring rock size. Rock size estimation instruments are used to monitor, optimize and control milling and crushing in the mining industry...

Genetic Diversity of Turf-Type Tall Fescue Using Diversity Arrays Technology

Czech Academy of Sciences Publication Activity Database

Baird, J. H.; Kopecký, David; Lukaszewski, A.J.; Green, R. J.; Bartoš, Jan; Doležel, Jaroslav

2012-01-01

Roč. 52, č. 1 (2012), s. 408-412 ISSN 0011-183X Institutional research plan: CEZ:AV0Z50380511 Keywords : Festuca arundinacea * Diversity Arrays Technology (DArT) * Low genetic polymorphism Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 1.513, year: 2012

Unusual metabolic diversity of hyperalkaliphilic microbial communities associated with subterranean serpentinization at The Cedars.

Science.gov (United States)

Suzuki, Shino; Ishii, Shun'ichi; Hoshino, Tatsuhiko; Rietze, Amanda; Tenney, Aaron; Morrill, Penny L; Inagaki, Fumio; Kuenen, J Gijs; Nealson, Kenneth H

2017-11-01

Water from The Cedars springs that discharge from serpentinized ultramafic rocks feature highly basic (pH=~12), highly reducing (E h serpentinizing system, was dominated by several bacterial taxa from the phyla OD1 ('Parcubacteria') and Chloroflexi. Members of the GPS1 community had, for the most part, the smallest genomes reported for their respective taxa, and encoded only archaeal (A-type) ATP synthases or no ATP synthases at all. Furthermore, none of the members encoded respiration-related genes and some of the members also did not encode key biosynthesis-related genes. In contrast, BS5, fed by shallow water, appears to have a community driven by hydrogen metabolism and was dominated by a diverse group of Proteobacteria similar to those seen in many terrestrial serpentinization sites. Our findings indicated that the harsh ultrabasic geological setting supported unexpectedly diverse microbial metabolic strategies and that the deep-water-fed springs supported a community that was remarkable in its unusual metagenomic and genomic constitution.

Processes of water rock interaction in the Turonian aquifer of Oum Er-Rabia Basin, Morocco

Science.gov (United States)

Ettazarini, Said

2005-12-01

Possible water rock interaction processes, in the Moroccan basin of Oum Er-Rabia, were discussed by a geochemical study of groundwater from the Turonian limestone aquifer, the most important water resource in the region. Different types of water according to the classification of Piper were defined. Waters have shown an evolution from dominant CHO3 Ca Mg type through mixed to SO4 Cl Ca Mg type. The use of geochemical diagrams and chemical speciation modeling method has shown that water rock interaction is mainly controlled by carbonate and anhydrite dissolution, ion exchange and reverse ion exchange processes. Water rock equilibrium conditions are favorable for the precipitation of calcite, dolomite, kaolinite and magnesian smectite.

Development of rock segment for reduction of amount of cement use

International Nuclear Information System (INIS)

Tada, Hiroyuki; Kumasaka, Hiroo; Saito, Akira; Nakaya, Atsushi; Ishii, Takashi; Sanada, Masanori; Noguchi, Akira; Kishi, Hirokazu; Nakama, Shigeo; Fujita, Tomoo

2013-01-01

The authors have been developing methods for constructing tunnels using the minimum quantities of cement-type support materials in high-level radioactive waste disposal facilities and advancing research and development about the technical formation of rock segment using low alkali mortar. In this study, the mechanical characteristic values concerning the rock segment and backfill materials were examined. The stability analysis of drift supported by the rock segment and backfilling with gravel were performed. Technical formation and effectiveness of the support planned for further reduction in cement influence was confirmed from the study result. (author)

Agronomic behavior of phosphoric rock from Bahia Inglesa using isotopic techniques. 2. Greenhouse experiment in three volcanic ash soils

International Nuclear Information System (INIS)

Pino N, I.; Casas G, L.

1989-01-01

With the aim to evaluate the behaviour of phosphoric rock in regard to the sorption capacity from three volcanic ash soils, a greenhouse trial was carried out. The isotopic dilution method with triple superphosphate labeled P32 (TSP-32) was used. Total dry matter, P total was determined by colorimetry and the liquid scintillation method for P32 was used. The evaluation of the rock was measured through different isotopical parameters such as A value and P derived from the rock. The behaviour of this material was affected by the different properties of the soils mainly on account of the diverse sorption capacity of them giving an inverse relation among sorption and effectiveness of the rock. The results showed a higher efficiency of TSP for the three soils compared with the phosphoric rock either concentrated or not. (author)

Quantitative rock-fall hazard and risk assessment for Yosemite Valley, Yosemite National Park, California

Science.gov (United States)

Stock, Greg M.; Luco, Nicolas; Collins, Brian D.; Harp, Edwin L.; Reichenbach, Paola; Frankel, Kurt L.

2014-01-01

Rock falls are common in Yosemite Valley, California, posing substantial hazard and risk to the approximately four million annual visitors to Yosemite National Park. Rock falls in Yosemite Valley over the past few decades have damaged structures and caused injuries within developed regions located on or adjacent to talus slopes highlighting the need for additional investigations into rock-fall hazard and risk. This assessment builds upon previous investigations of rock-fall hazard and risk in Yosemite Valley and focuses on hazard and risk to structures posed by relatively frequent fragmental-type rock falls as large as approximately 100,000 (cubic meters) in volume.

Culex pipiens crossing type diversity is governed by an amplified and polymorphic operon of Wolbachia.

Science.gov (United States)

Bonneau, Manon; Atyame, Celestine; Beji, Marwa; Justy, Fabienne; Cohen-Gonsaud, Martin; Sicard, Mathieu; Weill, Mylène

2018-01-22

Culex pipiens mosquitoes are infected with Wolbachia (wPip) that cause an important diversity of cytoplasmic incompatibilities (CIs). Functional transgenic studies have implicated the cidA-cidB operon from wPip and its homolog in wMel in CI between infected Drosophila males and uninfected females. However, the genetic basis of the CI diversity induced by different Wolbachia strains was unknown. We show here that the remarkable diversity of CI in the C. pipiens complex is due to the presence, in all tested wPip genomes, of several copies of the cidA-cidB operon, which undergoes diversification through recombination events. In 183 isofemale lines of C. pipiens collected worldwide, specific variations of the cidA-cidB gene repertoires are found to match crossing types. The diversification of cidA-cidB is consistent with the hypothesis of a toxin-antitoxin system in which the gene cidB co-diversifies with the gene cidA, particularly in putative domains of reciprocal interactions.

Relating rock avalanche morphology to emplacement processes

Science.gov (United States)

Dufresne, Anja; Prager, Christoph; Bösmeier, Annette

2015-04-01

The morphology, structure and sedimentological characteristics of rock avalanche deposits reflect both internal emplacement processes and external influences, such as runout path characteristics. The latter is mainly predisposed by topography, substrate types, and hydrogeological conditions. Additionally, the geological setting at the source slope controls, e.g. the spatial distribution of accumulated lithologies and hence material property-related changes in morphology, or the maximum clast size and amount of fines of different lithological units. The Holocene Tschirgant rock avalanche (Tyrol, Austria) resulted from failure of an intensely deformed carbonate rock mass on the southeast face of a 2,370-m-high mountain ridge. The initially sliding rock mass rapidly fragmented as it moved towards the floor of the Inn River valley. Part of the 200-250 x 106 m3 (Patzelt 2012) rock avalanche debris collided with and moved around an opposing bedrock ridge and flowed into the Ötz valley, reaching up to 6.3 km from source. Where the Tschirgant rock avalanche spread freely it formed longitudinal ridges aligned along motion direction as well as smaller hummocks. Encountering high topography, it left runup ridges, fallback patterns (i.e. secondary collapse), and compressional morphology (successively elevated, transverse ridges). Further evidence for the mechanical landslide behaviour is given by large volumes of mobilized valley-fill sediments (polymict gravels and sands). These sediments indicate both shearing and compressional faulting within the rock avalanche mass (forming their own morphological units through, e.g. in situ bulldozing or as distinctly different hummocky terrain), but also indicate extension of the spreading landslide mass (i.e. intercalated/injected gravels encountered mainly in morphological depressions between hummocks). Further influences on its morphology are given by the different lithological units. E.g. the transition from massive dolomite

Structural bursts produced by high energy muons in the rock

International Nuclear Information System (INIS)

Honda, K.; Takahashi, T.; Teramoto, Y.; Higashi, S.; Ozaki, S.

1975-01-01

Lateral structures of bursts produced by high energy muons in the rock have been observed at a depth 30 mw. e. underground by use of two layers of proportional counters. The running times were 7940 hr. The number of structural bursts observed, which have two cores in the both layers ( 1 >= 200, N 2 >= 20 particles) is 110, 1.6% of total events. These structural bursts have two types; 1) incident directions of two cores are parallel, 2) two cores intersect in the rock within 2 m above the roof of the tunnel. The events of this 2) type have large transverse momentum. (orig.) [de

Diffusion in the matrix of rocks from Olkiluoto. The effect of anion exclusion

International Nuclear Information System (INIS)

Valkiainen, M.; Aalto, H.; Olin, M.; Lindberg, A.; Siitari-Kauppi, M.

1995-12-01

Diffusion in the rock matrix is dependent on two basic factors: the effective diffusion conductivity of the rock and the rock-capacity factor. The aim of this ongoing research is to study both of these factors more closely by finding evidence and studying the significance of anion exclusion and surface diffusion. The material for the study was selected form the drill-core of the drill-hole OL-KR5 from Olkiluoto investigations site. Six rock-types were included in the study, three unaltered and three altered. The water-types selected can be divided to two groups: in one the ionic strength is varied, in the another the ionic type is varied. The diffusion measurements were carried out partly by the equilibration-leaching method, partly by the through-diffusion method. The measurements by the equilibration-leaching method were performed in the anaerobic cabinet and the through-diffusion measurement in laboratory room conditions. Radioactive isotopes 3 H, 35 S, 36 Cl and 22 Na were selected as tracers. This report contains results of the equilibration-leaching measurements and through- diffusion measurements using 3 H (HTO), 36 Cl (Cl-) and 35 S(SO 4 2- ) as tracers. The rock-types under study were also studied in the University of Helsinki, Department of Chemistry using polymethylmethacrylate labelled with 14 C revealing the pore structure. Also, results of specific surface area measurements made in BAM, Berlin are given. The comparison of results obtained by the gas diffusion method at the University of Jyvaeskylae to the results obtained by tritium are also appended. (12 refs., 20 figs., 10 tabs.)

Dynamic elastic moduli of rocks under pressure

Energy Technology Data Exchange (ETDEWEB)

Schock, R N [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

1970-05-01

Elastic moduli are determined as a function of confining pressure to 10 kb on rocks in which Plowshare shots are to be fired. Numerical simulation codes require accurate information on the mechanical response of the rock medium to various stress levels in order to predict cavity dimensions. The theoretical treatment of small strains in an elastic medium relates the propagation velocity of compressional and shear waves to the elastic moduli. Velocity measurements can provide, as unique code input data, the rigidity modulus, Poisson' ratio and the shear wave velocity, as well as providing checks on independent determinations of the other moduli. Velocities are determined using pulsed electro-mechanical transducers and measuring the time-of-flight in the rock specimen. A resonant frequency of 1 MHz is used to insure that the wavelength exceeds the average grain dimension and is subject to bulk rock properties. Data obtained on a variety of rock types are presented and analyzed. These data are discussed in terms of their relationship to moduli measured by static methods as well as the effect of anisotropy, porosity, and fractures. In general, fractured rocks with incipient cracks show large increases in velocity and moduli in the first 1 to 2 kb of compression as a result of the closing of these voids. After this, the velocities increase much more slowly. Dynamic moduli for these rocks are often 10% higher than corresponding static moduli at low pressure, but this difference decreases as the voids are closed until the moduli agree within experimental error. The discrepancy at low pressure is a result of the elastic energy in the wave pulse being propagated around cracks, with little effect on propagation velocity averaged over the entire specimen. (author)

Dynamic elastic moduli of rocks under pressure

International Nuclear Information System (INIS)

Schock, R.N.

1970-01-01

Elastic moduli are determined as a function of confining pressure to 10 kb on rocks in which Plowshare shots are to be fired. Numerical simulation codes require accurate information on the mechanical response of the rock medium to various stress levels in order to predict cavity dimensions. The theoretical treatment of small strains in an elastic medium relates the propagation velocity of compressional and shear waves to the elastic moduli. Velocity measurements can provide, as unique code input data, the rigidity modulus, Poisson' ratio and the shear wave velocity, as well as providing checks on independent determinations of the other moduli. Velocities are determined using pulsed electro-mechanical transducers and measuring the time-of-flight in the rock specimen. A resonant frequency of 1 MHz is used to insure that the wavelength exceeds the average grain dimension and is subject to bulk rock properties. Data obtained on a variety of rock types are presented and analyzed. These data are discussed in terms of their relationship to moduli measured by static methods as well as the effect of anisotropy, porosity, and fractures. In general, fractured rocks with incipient cracks show large increases in velocity and moduli in the first 1 to 2 kb of compression as a result of the closing of these voids. After this, the velocities increase much more slowly. Dynamic moduli for these rocks are often 10% higher than corresponding static moduli at low pressure, but this difference decreases as the voids are closed until the moduli agree within experimental error. The discrepancy at low pressure is a result of the elastic energy in the wave pulse being propagated around cracks, with little effect on propagation velocity averaged over the entire specimen. (author)

A study about the long-term stability of sedimentary rock

International Nuclear Information System (INIS)

Yoshino, Naoto; Miyanomae, Shun-ichi; Inoue, Hiroyuki; Nashimoto, Yutaka

2005-02-01

In this paper, following two issues were examined and estimated, (1) the influence of near field condition factor to the dynamical behavior of sedimentary soft rock, (2) the long term estimation of the dynamical behavior considering the condition of Horonobe area. As the study about the influence of near field condition factor to the dynamical behavior of sedimentary soft rock, the thermal factor was focused on and the laboratory tests using test pieces which were sampled in Horonobe area were carried out under the water temperature were 20 degrees and 80 degrees. As a result, the time dependence parameter in variable-compliance-type constitutive-equation could be obtained. And comparison between creep property under 20 degrees and 80 degrees was conducted. In addition, the general properties of sedimentary soft rock under several conditions were identified by the survey of the literature. And the way how to confirm the dynamical properties of sedimentary soft rock with in-situ test were presented. For the study on the short-term and long-term stability of rock surrounding buffer materials, numerical simulations were carried out assuming several conditions. The direction of disposal tunnels and the ratio of rock strength by initial stress were estimated to be the main factor affecting the short-term stability of rock. Time dependency of rock and the stiffness of buffer material were estimated to be the main factor affecting the long-term stability of rock. (author)

Constitutive relationships for elastic deformation of clay rock: Data Analysis

Energy Technology Data Exchange (ETDEWEB)

Liu, H.H.; Rutqvist, J.; Birkholzer, J.T.

2011-04-15

Geological repositories have been considered a feasible option worldwide for storing high-level nuclear waste. Clay rock is one of the rock types under consideration for such purposes, because of its favorable features to prevent radionuclide transport from the repository. Coupled hydromechanical processes have an important impact on the performance of a clay repository, and establishing constitutive relationships for modeling such processes are essential. In this study, we propose several constitutive relationships for elastic deformation in indurated clay rocks based on three recently developed concepts. First, when applying Hooke's law in clay rocks, true strain (rock volume change divided by the current rock volume), rather than engineering strain (rock volume change divided by unstressed rock volume), should be used, except when the degree of deformation is very small. In the latter case, the two strains will be practically identical. Second, because of its inherent heterogeneity, clay rock can be divided into two parts, a hard part and a soft part, with the hard part subject to a relatively small degree of deformation compared with the soft part. Third, for swelling rock like clay, effective stress needs to be generalized to include an additional term resulting from the swelling process. To evaluate our theoretical development, we analyze uniaxial test data for core samples of Opalinus clay and laboratory measurements of single fractures within macro-cracked Callovo-Oxfordian argillite samples subject to both confinement and water reduced swelling. The results from this evaluation indicate that our constitutive relationships can adequately represent the data and explain the related observations.

Constitutive relationships for elastic deformation of clay rock: Data Analysis

International Nuclear Information System (INIS)

Liu, H.H.; Rutqvist, J.; Birkholzer, J.T.

2011-01-01

Geological repositories have been considered a feasible option worldwide for storing high-level nuclear waste. Clay rock is one of the rock types under consideration for such purposes, because of its favorable features to prevent radionuclide transport from the repository. Coupled hydromechanical processes have an important impact on the performance of a clay repository, and establishing constitutive relationships for modeling such processes are essential. In this study, we propose several constitutive relationships for elastic deformation in indurated clay rocks based on three recently developed concepts. First, when applying Hooke's law in clay rocks, true strain (rock volume change divided by the current rock volume), rather than engineering strain (rock volume change divided by unstressed rock volume), should be used, except when the degree of deformation is very small. In the latter case, the two strains will be practically identical. Second, because of its inherent heterogeneity, clay rock can be divided into two parts, a hard part and a soft part, with the hard part subject to a relatively small degree of deformation compared with the soft part. Third, for swelling rock like clay, effective stress needs to be generalized to include an additional term resulting from the swelling process. To evaluate our theoretical development, we analyze uniaxial test data for core samples of Opalinus clay and laboratory measurements of single fractures within macro-cracked Callovo-Oxfordian argillite samples subject to both confinement and water reduced swelling. The results from this evaluation indicate that our constitutive relationships can adequately represent the data and explain the related observations.

Mechanical weathering and rock erosion by climate-dependent subcritical cracking

Science.gov (United States)

Eppes, Martha-Cary; Keanini, Russell

2017-06-01

This work constructs a fracture mechanics framework for conceptualizing mechanical rock breakdown and consequent regolith production and erosion on the surface of Earth and other terrestrial bodies. Here our analysis of fracture mechanics literature explicitly establishes for the first time that all mechanical weathering in most rock types likely progresses by climate-dependent subcritical cracking under virtually all Earth surface and near-surface environmental conditions. We substantiate and quantify this finding through development of physically based subcritical cracking and rock erosion models founded in well-vetted fracture mechanics and mechanical weathering, theory, and observation. The models show that subcritical cracking can culminate in significant rock fracture and erosion under commonly experienced environmental stress magnitudes that are significantly lower than rock critical strength. Our calculations also indicate that climate strongly influences subcritical cracking—and thus rock weathering rates—irrespective of the source of the stress (e.g., freezing, thermal cycling, and unloading). The climate dependence of subcritical cracking rates is due to the chemophysical processes acting to break bonds at crack tips experiencing these low stresses. We find that for any stress or combination of stresses lower than a rock's critical strength, linear increases in humidity lead to exponential acceleration of subcritical cracking and associated rock erosion. Our modeling also shows that these rates are sensitive to numerous other environment, rock, and mineral properties that are currently not well characterized. We propose that confining pressure from overlying soil or rock may serve to suppress subcritical cracking in near-surface environments. These results are applicable to all weathering processes.

Rock stress investigations

International Nuclear Information System (INIS)

Pahl, A.; Heusermann, St.; Braeuer, V.; Gloeggler, W.

1989-04-01

On the research project 'Rock Stress Mesurements' the BGR has developed and tested several methods for use in boreholes at a depth of 200 m. Indirect stress measurements using overcoring methods with BGR-probes and CSIR-triaxial cells as well as direct stress measurements using the hydraulic-fracturing method were made. To determine in-situ rock deformation behavior borehole deformation tests, using a BGR-dilatometer, were performed. Two types of the BGR-probe were applied: a four-component-probe to determine horizontal stresses and a five-component-probe to determine a quasi three-dimensional stress field. The first time a computer for data processing was installed in the borehole together with the BGR-probe. Laboratory tests on low cylinders were made to study the stress-deformation behavior. To validate and to interprete the measurement results some test methods were modelled using the finite-element method. The dilatometer-tests yielded high values of Young's modulus, whereas laboratory tests showed lower values with a distinct deformation anisotropy. Stress measurements with the BGR-probe yielded horizontal stresses being higher than the theoretical overburden pressure. These results are comparable to the results of the hydraulic fracturing tests, whereas stresses obtained with CSIR-triaxial cells are lower. The detailed geological mapping of the borehole indicated relationships between stress and geology. With regard to borehole depth different zones of rock structure joint frequency, joint orientation, and orientation of microfissures as well as stress magnitude, stress direction, and degree of deformation anisotropy could be distinguished. (author) 4 tabs., 76 figs., 31 refs

Palladium, platinum, and rhodium contents of rocks near the lower margin of the Stillwater complex, Montana.

Science.gov (United States)

Zientek, M.L.; Foose, M.P.; Leung, Mei

1986-01-01

Statistical summaries are reported for Pd, Pt and Rh contents of rocks from the lower part of the Stillwater complex, the underlying contact-metamorphosed sediments, and post-metamorphic dykes and sills wholly within the hornfelses. Variability of the data among the rock types is attributed largely to differences in sulphide content. Non-correlation of sulphur with platinum-group assays of many rock types leads to the suggestion that the immiscible sulphide and silicate liquids did not completely equilibrate with respect to platinum-group elements. -G.J.N.

Reducing rock fall injuries in underground US coal mines

Energy Technology Data Exchange (ETDEWEB)

Robertson, S.B.; Molinda, G.M.; Pappas, D.M. [Pittsburgh Research Laboratory, Pittsburgh, PA (United States)

2005-07-01

A continuing risk to underground US coal miners is rock falling from the mine roof. Almost 99% of injuries caused by rock falls are not from a major roof collapse, but from smaller rock that fall from between roof bolts. Installing roof screen provides excellent overhead roof coverage and dramatically reduces the potential for rock fall injuries, especially to roof bolted operators. The National Institute for Occupational Safety and Health (NIOSH) has explored different installation techniques and roof screening options along with machine design innovations that make roof screening easier and safer. Applying ergonomic principles to roof screening will offer insight and direction for better material handling. Other techniques for controlling rock falls and roof falls for long-term stability include the application of surface support liners and polyurethane (PUR) injection. An ongoing study at the NIOSH Lake Lynn Laboratory of various types of spray-on liner and shotcrete materials is providing a unique opportunity to evaluate the long-term behaviour of liners in an underground environment. In-mine studies of PUR have involved pre- and post-injection core drilling and video borecole logging. The results have provided insights into how PUR penetrates and reinforces weak and highly fractured rock. 11 refs., 8 figs., 1 tab.

Acquisition and preparation of specimens of rock for large-scale testing

International Nuclear Information System (INIS)

Watkins, D.J.

1981-01-01

The techniques used for acquisition and preparation of large specimens of rock for laboratory testing depend upon the location of the specimen, the type of rock and the equipment available at the sampling site. Examples are presented to illustrate sampling and preparation techniques used for two large cylindrical samples of granitic material, one pervasively fractured and one containing a single fracture

Pb, Sr, and Nd isotopic compositions of a suite of Large Archean, igneous rocks, eastern Beartooth Mountains - Implications for crust-mantle evolution

Science.gov (United States)

Wooden, J. L.; Mueller, P. A.

1988-01-01

Compositionally diverse Late Archean rocks (2.74-2.79 Ga old) from the eastern Beartooth Mountains (Montana and Wyoming) were studied and shown to have the same initial Pb, Sr, and Nd isotopic ratios. Lead and Sr initial ratios are higher and Nd initial values lower than predicted for rocks derived from model mantle sources and strongly indicate the involvement of an older crustal reservoir in the genesis of these rocks. A model involving subduction of continental detritus and contamination of the overlying mantle is suggested.

Simulation of crack propagation in rock in plasma blasting technology

Science.gov (United States)

Ikkurthi, V. R.; Tahiliani, K.; Chaturvedi, S.

Plasma Blasting Technology (PBT) involves the production of a pulsed electrical discharge by inserting a blasting probe in a water-filled cavity drilled in a rock, which produces shocks or pressure waves in the water. These pulses then propagate into the rock, leading to fracture. In this paper, we present the results of two-dimensional hydrodynamic simulations using the SHALE code to study crack propagation in rock. Three separate issues have been examined. Firstly, assuming that a constant pressure P is maintained in the cavity for a time τ , we have determined the P- τ curve that just cracks a given rock into at least two large-sized parts. This study shows that there exists an optimal pressure level for cracking a given rock-type and geometry. Secondly, we have varied the volume of water in which the initial energy E is deposited, which corresponds to different initial peak pressures Ppeak. We have determined the E- Ppeak curve that just breaks the rock into four large-sized parts. It is found that there must be an optimal Ppeak that lowers the energy consumption, but with acceptable probe damage. Thirdly, we have attempted to identify the dominant mechanism of rock fracture. We also highlight some numerical errors that must be kept in mind in such simulations.

Golovkinskii law for prediction of distribution of rock lithotypes of Permian deposits (east part of Russian plate)

Science.gov (United States)

Sitdikova, Lyalya; Izotov, Victor; Berthault, Gi; Lalomov, Alexander

2010-05-01

Zone of development of upper-permian-kazanian deposits in Volga-Kama petroleum province is the region of facies interrelations law identification. This law is known as the rule of Golovkinskii-Valter. Many details of geological formations relationship in change zones are still discussed. Efforts of analytic expression of Golovkinskii rule for specific regions of its development are very important. We analyzed width of horizons of the Kazanian Stage. They are in zone of facies change of marine gray and red formations of the east part of Russian plate. Results of this analysis were principle for analytic expression of Golovkinskii rule. Percent proportion of main lithological types of these rock formations was also used. We used profile which was based on data from 75 wells. This profile crosses region of development of kazanian deposits from the river Volga to Urals territory. It overpasses main structural and tectonic units of the region: Kazan-Kirov downfold, system of lifted blocks of Tatar Arch and Upper-Kama depression. Kazanian deposits of Kazan-Kirov downfold are represented by typical marine gray carbonate-terrigenous formation. Red formation is deposed within Upper-Kama depression. Zone of these formations relationship is limited to central parts of Tatar Arch. Abrupt fluctuations of content of one rock type in insignificant distance are common. Every rock type has unique features in its distribution on profile. That's why it is possible to study function of dependence of certain rock type content from distance as a sum of regular and chance components. Intensively rising change of proportions of different rock types is presented in the zone of transition from typical marine deposits to red deposits. So trends of variation of percent content (y) of main rock lithotypes depending on distance (x) can be described by simple difference equations: dy = -kdx, for rocks of marine gray formation. dy = k(M-y)dx, for rocks of red formation. M - mathematical

Latitudinal variation of diversity in European freshwater animals is not concordant across habitat types

DEFF Research Database (Denmark)

Hof, Christian; Brändle, Martin; Brandl, Roland

2008-01-01

Aim We analysed the variation of species richness in the European freshwater fauna across latitude. In particular, we compared latitudinal patterns in species richness and ß -diversity among species adapted to different habitat types. Location Europe. Methods We compiled data on occurrence for 14......,020 animal species across 25 pre-defined biogeographical regions of European freshwaters from the Limnofauna Europaea . Furthermore, we extracted information on the habitat preferences of species. We assigned species to three habitat types: species adapted to groundwater, lotic (running water) and lentic...... richness among species adapted to different habitat types are in part due to differences in the propensity for dispersal. Since lentic habitats are less persistent than lotic or groundwater habitats, lentic species evolved more efficient strategies for dispersal. The dispersal propensity of lentic species...

Experimental Studies on Permeability of Intact and Singly Jointed Meta-Sedimentary Rocks Under Confining Pressure

Science.gov (United States)

Wong, Louis Ngai Yuen; Li, Diyuan; Liu, Gang

2013-01-01

Three different types of permeability tests were conducted on 23 intact and singly jointed rock specimens, which were cored from rock blocks collected from a rock cavern under construction in Singapore. The studied rock types belong to inter-bedded meta-sandstone and meta-siltstone with very low porosity and high uniaxial compressive strength. The transient pulse water flow method was employed to measure the permeability of intact meta-sandstone under a confining pressure up to 30 MPa. It showed that the magnitude order of meta-sandstone's intrinsic permeability is about 10-18 m2. The steady-state gas flow method was used to measure the permeability of both intact meta-siltstone and meta-sandstone in a triaxial cell under different confining pressures spanning from 2.5 to 10 MPa. The measured permeability of both rock types ranged from 10-21 to 10-20 m2. The influence of a single natural joint on the permeability of both rock types was studied by using the steady-state water flow method under different confining pressures spanning from 1.25 to 5.0 MPa, including loading and unloading phases. The measured permeability of both jointed rocks ranged from 10-13 to 10-11 m2, where the permeability of jointed meta-siltstone was usually slightly lower than that of jointed meta-sandstone. The permeability of jointed rocks decreases with increasing confining pressure, which can be well fitted by an empirical power law relationship between the permeability and confining pressure or effective pressure. The permeability of partly open cracked specimens is lower than that of open cracked specimens, but it is higher than that of the specimen with a dominant vein for the meta-sandstone under the same confining pressure. The permeability of open cracked rock specimens will partially recover during the unloading confining pressure process. The equivalent crack (joint) aperture is as narrow as a magnitude order of 10-6 m (1 μm) in the rock specimens under confining pressures

Experimental Research on the Specific Energy Consumption of Rock Breakage Using Different Waterjet-Assisted Cutting Heads

Directory of Open Access Journals (Sweden)

Hongxiang Jiang

2018-01-01

Full Text Available To investigate the specific energy consumption (SE of rock breakage by cutting heads assisted by different types of waterjet and to identify optimal waterjet parameters and assistance types, rock cutting with and without waterjets was carried on a rock fragmentation test bed. SE is a comprehensive evaluation index and was developed according to the applied load on cutting head, and the SE under different cutting conditions was compared and analyzed. The results show that the SE of rock breakage without waterjet assistance increased with the increasing of rock compressive strength (RCS but that the limited drilling depth decreased. The effect of the waterjet pressure on the SE of rock breakage by the cutting head I was marked, and SE decreased by 30∼40% when the ratio between RCS and waterjet pressure was less than 1. However, the function of the waterjet assistance was poor; therefore, a ratio of 1 could be used to distinguish the rock breakage effect of cutting head I. For cutting head II, the rock damage from the waterjet impact was limited due to the large waterjet standoff distance; thus the rock breakage performance of cutting head II was also limited. The waterjet impacting at the tip of the conical pick using cutting head III could enter into the cracks caused by the mechanical pick and fracture the rock. Therefore, the rock breakage performance of cutting head III was better than that of cutting head II.

Rocks Can Wow? Yes, Rocks Can Wow!

Science.gov (United States)

Hardman, Sally; Luke, Sue

2016-01-01

Rocks and fossils appear in the National Curriculum of England science programmes of study for children in year 3 (ages 7-8). A frequently asked question is "How do you make the classification of rocks engaging?" In response to this request from a school, a set of interactive activities was designed and organised by tutors and students…

A study of radioactive elements of various rocks in Pattani Province with gamma ray spectrometer

Directory of Open Access Journals (Sweden)

Kaewtubtim, P.

2002-01-01

Full Text Available The radioactivity of the three elements, potassium, uranium and thorium, in rocks of various types in Pattani Province was investigated by using a gamma ray spectrometer. It was found that potassium contents in igneous rocks, sedimentary rocks and metamorphic rocks were 6.29 %, 2.21% and 1.54 % respectively. Uranium equivalent contents in igneous rock, sedimentary rocks and metamorphic rocks were found to be 22.51 ppm, 11.25 ppm and 14.13 ppm, while thorium contents in these rocks were 21.78 ppm, 18.88 ppm and 18.15 ppm respectively. The results obtained were similar to those reported by Pungtip Ranglek (1995 for igneous rock at Liwong Pluton site in Thepha, Na Thawi, Chana and Saba Yoi Districts, Songkhla Province, and were about six times higher than those reported by Kittichai Wattananikorn (1994 for igneous rock in the northern part of Thailand.

Stress Analysis and Model Test of Rock Breaking by Arc Blade Wedged Hob

Directory of Open Access Journals (Sweden)

Ying-chao Liu

2016-07-01

Full Text Available Based on rock compression-shear damage theory, the mechanical characteristics of an arc blade wedged hob were analyzed to study the rock fragmentation mechanism of hob during excavation, and rock fragmentation forecasting model of the arc blade wedged hob was improved. A spoke type cutter model which is similar to the tunnel boring machine (TBM cutter head was designed to study the rock fragmentation efficiency in different cutter spacing by adjusting the bearing sleeve size to obtain different distances between the hobs. The results show that the hob-breaking rock force mainly comes from three directions. The vertical force along the direction of the tunnel excavation, which is associated with uniaxial compressive strength of rock mass, plays a key role in the process of rock fragmentation. Field project data shows that the prediction model’s results of rock fragmentation in this paper are closer to the measured results than the results of the traditional linear cutting model. The optimal cutter spacing exists among different cutter spacings to get higher rock fragmentation rate and lower energy consumption during rock fragmentation. It is of great reference significance to design the arc blade wedged hob and enhance the efficiency of rock fragmentation in rock strata.

Experimental study of polyurethane foam reinforced soil used as a rock-like material

Directory of Open Access Journals (Sweden)

Eren Komurlu

2015-10-01

Full Text Available In this study, polyurethane foam type thermoset polymerizing, due to chemical reaction between its liquid ingredients, was tested as binder after solidifying and then a rock-like material mixing with a sandy silt type soil was prepared. The uniaxial compressive strengths (UCSs of polyurethane foam reinforced soil specimens were determined for different polyurethane ratios in the mixture. Additionally, a series of tests on slake durability, impact value, freezing–thawing resistance, and abrasion resistance of polyurethane reinforced soil (PRS mixture was conducted. The UCS values over 3 MPa were measured from the PRS specimens. The testing results showed that treated soil can economically become a desirable rock-like material in terms of slake durability and resistances against freezing–thawing, impact effect and abrasion. As another characteristic of the rock-like material made with polyurethane foam, unit volume weight was found to be quite lower than those of natural rock materials.

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Frictional property of rocks in the Izu-Bonin-Mariana Forearc under high temperature and pressure conditions

Science.gov (United States)

Hyodo, G.; Takahashi, M.; Saito, S.; Hirose, T.

2014-12-01

The Kanto region in central Japan lies atop of three tectonic plates: the North American Plate, the Pacific Plate, and the Philippine Sea Plate. The collision and subduction of the Izu-Bonin-Mariana (IBM) arc on the Philippine Sea Plate into the Kanto region results in occurring the different type of earthquakes, including seismic slip (e.g., the Kanto earthquake) and aseismic creep (i.e., slow earthquakes around the Boso peninsula). The seismic and aseismic slip seems to generate side by side at almost same depth (probably nearly same P-T conditions). This study focus on frictional property of incoming materials to be subducted into the Kanto region, in order to examine a hypothesis that the different types of slips arise from different input materials. Thus, we have performed friction experiments on rocks that constitute the IBM forearc using a high P-T gas medium apparatus at AIST. We sampled five rocks (marl, boninite, andesite, sheared serpentinite and serpentinized dunite) recovered from the IBM forearc by Leg 125, Ocean Drilling Program (ODP Site 784, 786). The rocks were crushed and sieved into 10˜50 µm in grain size. Experiments were conducted at temperature of 300○C, confining pressure of 156 MPa, pore pressure of 60 MPa and axial displacement rates of 0.1 and 1 µm/s. For marl, andesite and boninite, a periodic stick-slip behavior appears at 1 µm/s. Rise time of the stick-slip behaviors are quite long (3.1, 9.9 and 14.2 sec, for marl, andesite and boninite, respectively). We called such events as a "slow stick-slip". Similar slow stick-slip behaviors were observed in previous studies (Noda and Shimamoto, 2010; Okazaki, 2013; Kaproth and Marone, 2013), but this is first time to recognize this characteristic slip behavior in sedimentary and igneous rocks. Although it is difficult to discuss the diverse slip behaviors observed at the Kanto region based on our limited experimental results, we will examine the conditions where the transition between

Geochemical characterization of Parana Basin volcanic rocks: petrogenetic implications

International Nuclear Information System (INIS)

Marques, L.S.

1988-01-01

A detailed study of the geochemical characteristics of Parana Basin volcanic rocks is presented. The results are based on the analyses of major and trace elements of 158 samples. Ninety three of these volcanic samples belong to 8 flow sequences from Rio Grande do Sul and Santa Catarina States. The remaining sixty five samples are distributed over the entire basin. In order to study the influence of crustal contamination processes in changing chemical characteristics of the volcanic rocks, 47 samples representative of the crystalline basement of the southern and southeastern Parana Basin were also analysed. Several petrogenetic models were tested to explain the compocional variability of the volcanic rocks, in particular those of southern region. The results obtained sugest an assimilation-fractional crystallization process as viable to explain the differences of both the chemical characteristics and Sr isotope initial ratios observed in basic and intermediate rocks. A model involving melting processes of basic material, trapped at the base of the crust, with composition similar to low and high TiO 2 basalts appears to be a possibility to originate the Palmas and Chapeco acid melts, respectively. The study of ''uncontaminated'' or poorly contaminated low TiO 2 basic rocks from the southern, central and northern regions shows the existence of significant differences in the geochemical charactetistics according to their geographical occurrence. A similar geochemical diversity is also observed in high TiO 2 basalts and Chapeco volcanics. Differences in incompatible element ratios between low and high TiO 2 ''uncontaminated'' or poorly contaminated basalts suggest that they could have been produced by different degrees of melting in a garnet peridotite source. Geochemical and isotopic (Sr and Nd) data also support the view that basalts from northern and southern regions of Parana Basin originated from mantle source with different composition. (author) [pt

Simulation of rock deformation behavior

Directory of Open Access Journals (Sweden)

Я. И. Рудаев

2016-12-01

Full Text Available A task of simulating the deformation behavior of geomaterials under compression with account of over-extreme branch has been addressed. The physical nature of rock properties variability as initially inhomogeneous material is explained by superposition of deformation and structural transformations of evolutionary type within open nonequilibrium systems. Due to this the description of deformation and failure of rock is related to hierarchy of instabilities within the system being far from thermodynamic equilibrium. It is generally recognized, that the energy function of the current stress-strain state is a superposition of potential component and disturbance, which includes the imperfection parameter accounting for defects not only existing in the initial state, but also appearing under load. The equation of state has been obtained by minimizing the energy function by the order parameter. The imperfection parameter is expressed through the strength deterioration, which is viewed as the internal parameter of state. The evolution of strength deterioration has been studied with the help of Fokker – Planck equation, which steady form corresponds to rock statical stressing. Here the diffusion coefficient is assumed to be constant, while the function reflecting internal sliding and loosening of the geomaterials is assumed as an antigradient of elementary integration catastrophe. Thus the equation of state is supplemented with a correlation establishing relationship between parameters of imperfection and strength deterioration. While deformation process is identified with the change of dissipative media, coupled with irreversible structural fluctuations. Theoretical studies are proven with experimental data obtained by subjecting certain rock specimens to compression.

Fundamental Research on Percussion Drilling: Improved rock mechanics analysis, advanced simulation technology, and full-scale laboratory investigations

Energy Technology Data Exchange (ETDEWEB)

Michael S. Bruno

2005-12-31

drilling tests, as well as single impact tests, have been designed and executed. Both Berea sandstone and Mancos shale samples are used. In single impact tests, three impacts are sequentially loaded at the same rock location to investigate rock response to repetitive loadings. The crater depth and width are measured as well as the displacement and force in the rod and the force in the rock. Various pressure differences across the rock-indentor interface (i.e. bore pressure minus pore pressure) are used to investigate the pressure effect on rock penetration. For hammer drilling tests, an industrial fluid hammer is used to drill under both underbalanced and overbalanced conditions. Besides calibrating the modeling tool, the data and cuttings collected from the tests indicate several other important applications. For example, different rock penetrations during single impact tests may reveal why a fluid hammer behaves differently with diverse rock types and under various pressure conditions at the hole bottom. On the other hand, the shape of the cuttings from fluid hammer tests, comparing to those from traditional rotary drilling methods, may help to identify the dominant failure mechanism that percussion drilling relies on. If so, encouraging such a failure mechanism may improve hammer performance. The project is summarized in this report. Instead of compiling the information contained in the previous quarterly or other technical reports, this report focuses on the descriptions of tasks, findings, and conclusions, as well as the efforts on promoting percussion drilling technologies to industries including site visits, presentations, and publications. As a part of the final deliveries, the 3D numerical model for rock mechanics is also attached.

Ionization and Corona Discharges from Stressed Rocks

Science.gov (United States)

Winnick, M. J.; Kulahci, I.; Cyr, G.; Tregloan-Reed, J.; Freund, F. T.

2008-12-01

Pre-earthquake signals have long been observed and documented, though they have not been adequately explained scientifically. These signals include air ionization, occasional flashes of light from the ground, radio frequency emissions, and effects on the ionosphere that occur hours or even days before large earthquakes. The theory that rocks function as p-type semiconductors when deviatoric stresses are applied offers a mechanism for this group of earthquake precursors. When an igneous or high-grade metamorphic rock is subjected to deviatoric stresses, peroxy bonds that exist in the rock's minerals as point defects dissociate, releasing positive hole charge carriers. The positive holes travel by phonon-assisted electron hopping from the stressed into and through the unstressed rock volume and build up a positive surface charge. At sufficiently large electric fields, especially along edges and sharp points of the rock, air molecules become field-ionized, loosing an electron to the rock surface and turning into airborne positive ions. This in turn can lead to corona discharges, which manifest themselves by flashes of light and radio frequency emissions. We applied concentrated stresses to one end of a block of gabbro, 30 x 15 x 10 cm3, inside a shielded Faraday cage and observed positive ion currents through an air gap about 25 cm from the place where the stresses were applied, punctuated by short bursts, accompanied by flashes of light and radio frequency emissions characteristic of a corona discharge. These observations may serve to explain a range of pre-earthquake signals, in particular changes in air conductivity, luminous phenomena, radio frequency noise, and ionospheric perturbations.

Heat production rate from radioactive elements in igneous and metamorphic rocks in eastern desert, Egypt

International Nuclear Information System (INIS)

Abbady, A G.E.; Arabi, A.M.; Abbay, A.

2005-01-01

Radioactive heat - production data of igneous and metamorphic rocks cropping out from the eastern desert are presented. Samples were analysed using low level gamma-ray spectrometer (HPGe) in the laboratory. A total of 205 rock samples were investigated, covering all major rock types of the area. The heat-production rate of igneous rocks ranges from 0.11 (basalt) to 9.53 Μ Wm-3 (granite). In metamorphic rocks it varies from 0.28 (serpentinite) to 0.91 (metagabroo) Μ W.m-3. The contribution due to U is about (51%), whereas that of Th (31%) and (18%) by K. The corresponding values in igneous rocks are 76%: 19%: 5%, respectively. The calculated values showed good agreement with global values expect in some areas contained granite rocks

Targeting ROCK activity to disrupt and prime pancreatic cancer for chemotherapy.

Science.gov (United States)

Vennin, Claire; Rath, Nicola; Pajic, Marina; Olson, Michael F; Timpson, Paul

2017-10-03

Pancreatic ductal adenocarcinoma (PDAC) is a devastating disease; the identification of novel targets and development of effective treatment strategies are urgently needed to improve patient outcomes. Remodeling of the pancreatic stroma occurs during PDAC development, which drives disease progression and impairs responses to therapy. The actomyosin regulatory ROCK1 and ROCK2 kinases govern cell motility and contractility, and have been suggested to be potential targets for cancer therapy, particularly to reduce the metastatic spread of tumor cells. However, ROCK inhibitors are not currently used for cancer patient treatment, largely due to the overwhelming challenge faced in the development of anti-metastatic drugs, and a lack of clarity as to the cancer types most likely to benefit from ROCK inhibitor therapy. In 2 recent publications, we discovered that ROCK1 and ROCK2 expression were increased in PDAC, and that increased ROCK activity was associated with reduced survival and PDAC progression by enabling extracellular matrix (ECM) remodeling and invasive growth of pancreatic cancer cells. We also used intravital imaging to optimize ROCK inhibition using the pharmacological ROCK inhibitor fasudil (HA-1077), and demonstrated that short-term ROCK targeting, or 'priming', improved chemotherapy efficacy, disrupted cancer cell collective movement, and impaired metastasis. This body of work strongly indicates that the use of ROCK inhibitors in pancreatic cancer therapy as 'priming' agents warrants further consideration, and provides insights as to how transient mechanical manipulation, or fine-tuning the ECM, rather than chronic stromal ablation might be beneficial for improving chemotherapeutic efficacy in the treatment of this deadly disease.

Diversity and biotic homogenization of urban land-snail faunas in relation to habitat types and macroclimate in 32 central European cities.

Science.gov (United States)

Horsák, Michal; Lososová, Zdeňka; Čejka, Tomáš; Juřičková, Lucie; Chytrý, Milan

2013-01-01

The effects of non-native species invasions on community diversity and biotic homogenization have been described for various taxa in urban environments, but not for land snails. Here we relate the diversity of native and non-native land-snail urban faunas to urban habitat types and macroclimate, and analyse homogenization effects of non-native species across cities and within the main urban habitat types. Land-snail species were recorded in seven 1-ha plots in 32 cities of ten countries of Central Europe and Benelux (224 plots in total). Each plot represented one urban habitat type characterized by different management and a specific disturbance regime. For each plot, we obtained January, July and mean annual temperature and annual precipitation. Snail species were classified into either native or non-native. The effects of habitat type and macroclimate on the number of native and non-native species were analysed using generalized estimating equations; the homogenization effect of non-native species based on the Jaccard similarity index and homogenization index. We recorded 67 native and 20 non-native species. Besides being more numerous, native species also had much higher beta diversity than non-natives. There were significant differences between the studied habitat types in the numbers of native and non-native species, both of which decreased from less to heavily urbanized habitats. Macroclimate was more important for the number of non-native than native species; however in both cases the effect of climate on diversity was overridden by the effect of urban habitat type. This is the first study on urban land snails documenting that non-native land-snail species significantly contribute to homogenization among whole cities, but both the homogenization and diversification effects occur when individual habitat types are compared among cities. This indicates that the spread of non-native snail species may cause biotic homogenization, but it depends on scale and

Rock Physics

DEFF Research Database (Denmark)

Fabricius, Ida Lykke

2017-01-01

Rock physics is the discipline linking petrophysical properties as derived from borehole data to surface based geophysical exploration data. It can involve interpretation of both elastic wave propagation and electrical conductivity, but in this chapter focus is on elasticity. Rock physics is based...... on continuum mechanics, and the theory of elasticity developed for statics becomes the key to petrophysical interpretation of velocity of elastic waves. In practice, rock physics involves interpretation of well logs including vertical seismic profiling (VSP) and analysis of core samples. The results...

Mineral and rock chemistry of Mata da Corda Kamafugitic Rocks (Minas Gerais State, Brazil)

International Nuclear Information System (INIS)

Albuquerque Sgarbi, Patricia B. de; Valenca, Joel G.

1995-01-01

The volcanic rocks of the Mata da Corda Formation (Upper Cretaceous) in Minas Gerais, Brazil, are mafic potassic to ultra potassic rocks of kamafugitic affinity containing essentially clinopyroxenes, perovskite, magnetite and occasionally olivine, phlogopite, melilite pseudomorphs and apatite. The felsic phases are kalsilite and/or leucite pseudomorphs. The rocks are classified as mafitites, leucitites and kalsilitites. The analysis of the available data of the rocks studied, based on the relevant aspects of the main proposals for the classification of alkaline mafic to ultramafic potassic rocks leads to the conclusion that Sahama's (1974) proposal to divide potassium rich alkaline rocks in two large families is the one to which the Mata da Corda rocks adapt best. According to this and the data in the literature on the mineralogy and mineral and rock chemistries of the other similar occurrences, these rocks may be interpreted as alkaline potassic to ultra potassic rocks of hamafugitic affinity. 11 figs., 5 tabs

Relict zircon U-Pb age and O isotope evidence for reworking of Neoproterozoic crustal rocks in the origin of Triassic S-type granites in South China

Science.gov (United States)

Gao, Peng; Zheng, Yong-Fei; Chen, Yi-Xiang; Zhao, Zi-Fu; Xia, Xiao-Ping

2018-02-01

Granites derived from partial melting of sedimentary rocks are generally characterized by high δ18O values and abundant relict zircons. Such relict zircons are valuable in tracing the source rocks of granites and the history of crustal anatexis. Here we report in-situ U-Pb ages, O isotopes and trace elements in zircons from Triassic granites in the Zhuguangshan and Jiuzhou regions, which are located in the Nanling Range and the Darongshan area, respectively, in South China. Zircon U-Pb dating yields magma crystallization ages of 236 ± 2 Ma for the Zhuguangshan granites and 246 ± 2 Ma to 252 ± 3 Ma for the Jiuzhou granites. The Triassic syn-magmatic zircons are characterized by high δ18O values of 10.1-11.9‰ in Zhuguangshan and 8.5-13.5‰ in Jiuzhou. The relict zircons show a wide range of U-Pb ages from 315 to 2185 Ma in Zhuguangshan and from 304 to 3121 Ma in Jiuzhou. Nevertheless, a dominant age peak of 700-1000 Ma is prominent in both occurrences, demonstrating that their source rocks were dominated by detrital sediments weathered from Neoproterozoic magmatic rocks. Taking previous results for regional granites together, Neoproterozoic relict zircons show δ18O values in a small range from 5 to 8‰ for the Nanling granites but a large range from 5 to 11‰ for the Darongshan granites. In addition, relict zircons of Paleozoic U-Pb age occur in the two granitic plutons. They exhibit consistently high δ18O values similar to the Triassic syn-magmatic zircons in the host granites. These Paleozoic relict zircons are interpreted as the peritectic product during transient melting of the metasedimentary rocks in response to the intracontinental orogenesis in South China. Therefore, the relict zircons of Neoproterozoic age are directly inherited from the source rocks of S-type granites, and those of Paleozoic age record the transient melting of metasedimentary rocks before intensive melting for granitic magmatism in the Triassic.

Rock slope instabilities in Norway: First systematic hazard and risk classification of 22 unstable rock slopes

Science.gov (United States)

Böhme, Martina; Hermanns, Reginald L.; Oppikofer, Thierry; Penna, Ivanna

2016-04-01

Unstable rock slopes that can cause large failures of the rock-avalanche type have been mapped in Norway for almost two decades. Four sites have earlier been characterized as high-risk objects based on expertise of few researchers. This resulted in installing continuous monitoring systems and set-up of an early-warning system for those four sites. Other unstable rock slopes have not been ranked related to their hazard or risk. There are ca. 300 other sites known of which 70 sites were installed for periodic deformation measurements using multiple techniques (Global Navigation Satellite Systems, extensometers, measurement bolts, and others). In 2012 a systematic hazard and risk classification system for unstable rock slopes was established in Norway and the mapping approach adapted to that in 2013. Now, the first 22 sites were classified for hazard, consequences and risk using this classification system. The selection of the first group of sites to be classified was based on an assumed high hazard or risk and importance given to the sites by Norwegian media and the public. Nine of the classified 22 unstable rock slopes are large sites that deform inhomogeneously or are strongly broken up in individual blocks. This suggests that different failure scenarios are possible that need to be analyzed individually. A total of 35 failure scenarios for those nine unstable rock slopes were considered. The hazard analyses were based on 9 geological parameters defined in the classification system. The classification system will be presented based on the Gamanjunni unstable rock slope. This slope has a well developed back scarp that exposes 150 m preceding displacement. The lateral limits of the unstable slope are clearly visible in the morphology and InSAR displacement data. There have been no single structures observed that allow sliding kinematically. The lower extend of the displacing rock mass is clearly defined in InSAR data and by a zone of higher rock fall activity. Yearly

Relationship between the rock mass deformation and places of occurrence of seismological events

Energy Technology Data Exchange (ETDEWEB)

Janusz Makowka; Jozef Kabiesz; Lin-ming Ddou [Central Mining Institute, Katowice (Poland)

2009-09-15

Static effort of rock mass very rarely causes of rock burst in Polish coal mines. Rock bursts with source in the seismic tremor within the roof rock layers are prevailing. A seismic tremor is an effect of rupture or sliding in roof layers above the exploited panel in coal seam, sometime in a distance from actual exploitation. Sliding, as a rule occurs in fault zone and tremors in it are expected, but monolithic layer rupture is very hard to predict. In a past few years a practice of analyzing state of deformation in high energy seismic tremors zones has been employed. It let gathering experience thanks to witch determination of dangerous shape of reformatted roof is possible. In the paper some typical forms of roof rocks deformations leading to seismic tremor occurrence will be presented. In general these are various types of multidirectional rock layers bending. Real examples of seismic events and rock bursts in the Czech Republic will be shown. 5 refs., 6 figs.

Petrophysics at the rock matrix scale: hydraulic properties and petrographic interpretation

International Nuclear Information System (INIS)

Montoto, M.

2003-01-01

The main objective of this publication is to review, summarize and make comprehensive the hydraulic properties of rocks, at the rock matrix or in tact rock scale. Also to describe how to petrographically interpret those properties. For this purpose, the procedures for the characterization and visualisation of the rock-forming components and in special the water path-ways at that scale are explained. Further more, to establish a methodological approach for an appropriate petrographic interpretation of all the mentioned properties is intended. This Technical Report is applied to the geological solution for the final disposal of high level radioactive wastes. In any case, most of the aspects covered here are of scientific and technical interest for any researcher interested in the behaviour of water in rocks and vice versa, also in the potential fluid- rock interactions. The document is divided into six Chapters, mainly theoretical and methodological, and six Appen - dixes, more focussed to practical tests and procedures for rock characterization. Two significant rock types in high level radioactive waste, HLW, granites and clays, have been used for illustrating most of the examples here included. Under a wide geological perspective, it must be stated that in any geological scenario two different systems or scales coexist; the rock massif (with fractures of about m to km) and the rock matrix (with internal discontinuities such as fissures and cracks to the order of Fm to dm). Their different behaviour is considered in Chapter 1 as well as the specific role played by the rock matrix in the long- and short-term period. General considerations about physical properties of rocks and comparative advantages and disadvantages of the main candidate rocks for radioactive repositories are also included. (Author)

Characterization of rock samples and mineralogical controls on leachates

Science.gov (United States)

Hammarstrom, Jane M.; Cravotta, Charles A.; Galeone, Daniel G.; Jackson, John C.; Dulong, Frank T.; Hornberger, Roger J.; Brady, Keith B.C.

2009-01-01

Rocks associated with coal beds typically include shale, sandstone, and (or) limestone. In addition to common rock-forming minerals, all of these rock types may contain sulfide and sulfate minerals, various carbonate minerals, and organic material. These different minerals have inherently different solubility characteristics, as well as different acid-generating or acid-neutralizing potentials. The abundance and composition of sulfur- and carbonate-bearing minerals are of particular interest in interpreting the leaching column data because (1) pyrite and carbonate minerals are the primary controls on the acid-base account of a sample, (2) these minerals incorporate trace metals that can be released during weathering, and (3) these minerals readily react during weathering due to mineral dissolution and oxidation of iron.Rock samples were collected by the Pennsylvania Department of Environmental Protection (PaDEP) from five different sites to assess the draft standardized leaching column method (ADTI-WP2) for the prediction of weathering rates and water quality at coal mines. Samples were sent to USGS laboratories for mineralogical characterization and to ActLabs for chemical analysis. The samples represent a variety of rock types (shales, sandstones, and coal refuse) that are typical of coal overburden in the eastern United States. These particular samples were chosen for testing the weathering protocols because they represent a range of geochemical and lithologic characteristics, sulfur contents, and acid-base accounting characteristics (Hornberger et al., 2003). The rocks contain variable amounts of pyrite and carbonate minerals and vary in texture.This chapter includes bulk rock chemical data and detailed mineralogical and textural data for unweathered starting materials used in the interlaboratory validation study, and for two samples used in the early phases of leaching column tests (Wadesville Sandstone, Leechburg Coal Refuse). We also characterize some of the

Integrated analysis of rock mass deformation within shaft protective pillar

Directory of Open Access Journals (Sweden)

Ewa Warchala

2016-01-01

Full Text Available The paper presents an analysis of the rock mass deformation resulting from mining in the vicinity of the shaft protection pillar. A methodology of deformation prediction is based on a deterministic method using Finite Element Method (FEM. The FEM solution is based on the knowledge of the geomechanical properties of the various geological formations, tectonic faults, types of mining systems, and the complexity of the behaviour of the rock mass. The analysis gave the stress and displacement fields in the rock mass. Results of the analysis will allow for design of an optimal mining system. The analysis is illustrated by an example of the shaft R-VIII Rudna Mine KGHM Polish Copper SA.

Diversity, assembly and regulation of archaeal type IV pili-like and non-type-IV pili-like surface structures.

Science.gov (United States)

Lassak, Kerstin; Ghosh, Abhrajyoti; Albers, Sonja-Verena

2012-01-01

Archaea have evolved fascinating surface structures allowing rapid adaptation to changing environments. The archaeal surface appendages display such diverse biological roles as motility, adhesion, biofilm formation, exchange of genetic material and species-specific interactions and, in turn, increase fitness of the cells. Intriguingly, despite sharing the same functions with their bacterial counterparts, the assembly mechanism of many archaeal surface structures is rather related to assembly of bacterial type IV pili. This review summarizes our state-of-the-art knowledge about unique structural and biochemical properties of archaeal surface appendages with a particular focus on archaeal type IV pili-like structures. The latter comprise not only widely distributed archaella (formerly known as archaeal flagella), but also different highly specialized archaeal pili, which are often restricted to certain species. Recent findings regarding assembly mechanisms, structural aspects and physiological roles of these type IV pili-like structures will be discussed in detail. Recently, first regulatory proteins involved in transition from both planktonic to sessile lifestyle and in assembly of archaella were identified. To conclude, we provide novel insights into regulatory mechanisms underlying the assembly of archaeal surface structures. Copyright © 2012. Published by Elsevier Masson SAS.

Demonstrations of Gravity-Independent Mobility and Drilling on Natural Rock using Microspines

Science.gov (United States)

Parness, Aaron; Frost, Matthew; King, Jonathan P.; Thatte, Nitish

2012-01-01

The video presents microspine-based anchors be ing developed for gripping rocks on the surfaces of comets and asteroids, or for use on cliff faces and lava tubes on Mars. Two types of anchor prototypes are shown on supporting forces in all directions away from the rock; >160 N tangent, >150 N at 45?, and >180 N normal to the surface of the rock. A compliant robotic ankle with two active degrees of freedom interfaces these anchors to the Lemur IIB robot for future climbing trials. Finally, a rotary percussive drill is shown coring into rock regardless of gravitational orientation. As a harder- than-zero-g proof of concept, inverted drilling was performed creating 20mm diameter boreholes 83 mm deep in vesicular basalt samples while retaining 12 mm diameter rock cores in 3-6 pieces.

Review of potential host rocks for radioactive waste disposal in the Piedmont Province of Georgia

International Nuclear Information System (INIS)

Wenner, D.B.; Gillon, K.A.

1980-10-01

A literature study was conducted on the Piedmont province of Georgia to designate areas that may be favorable for field exploration for consideration of a repository for storage of radioactive waste. The criteria utilized in such a designation was based upon consideration of the rock unit having favorable geological, geotechnical, and geohydrological features. The most important are that the rock unit have: (1) satisfactory unit dimensions (> 100 km 2 outcrop area and at least 1500 meters (approx. 5000 feet) depth of a continuous rock type); and (2) acceptable geohydrological conditions. Among all rock types, it is concluded that the granites of the large post-metamorphic plutons and large, homogeneous orthogneissic units offer the most favorable geologic settings for exploration for siting a radioactive waste repository. Virtually all other rock types, including most metavolcanic and metasedimentary lithologies have unacceptable unit dimensions, generally unfavorable geohydrologic settings, and deleterious mechanical and physical geotechnical properties. After consideration of all major lithologies that comprise the Georgia Piedmont, the following units were deemed favorable: (1) the Elberton Pluton; (2) the Siloam Pluton; (3) the Sparta Pluton; (4) two unnamed plutons adjacent to the Snelson body of S.W. Georgia; (5) the Lithonia Gneiss; (6) basement orthogneisses and charnockites of the Pine Mountain Belt

Numerical Analyses of the Influence of Blast-Induced Damaged Rock Around Shallow Tunnels in Brittle Rock

Science.gov (United States)

Saiang, David; Nordlund, Erling

2009-06-01

Most of the railway tunnels in Sweden are shallow-seated (rock cover) and are located in hard brittle rock masses. The majority of these tunnels are excavated by drilling and blasting, which, consequently, result in the development of a blast-induced damaged zone around the tunnel boundary. Theoretically, the presence of this zone, with its reduced strength and stiffness, will affect the overall performance of the tunnel, as well as its construction and maintenance. The Swedish Railroad Administration, therefore, uses a set of guidelines based on peak particle velocity models and perimeter blasting to regulate the extent of damage due to blasting. However, the real effects of the damage caused by blasting around a shallow tunnel and their criticality to the overall performance of the tunnel are yet to be quantified and, therefore, remain the subject of research and investigation. This paper presents a numerical parametric study of blast-induced damage in rock. By varying the strength and stiffness of the blast-induced damaged zone and other relevant parameters, the near-field rock mass response was evaluated in terms of the effects on induced boundary stresses and ground deformation. The continuum method of numerical analysis was used. The input parameters, particularly those relating to strength and stiffness, were estimated using a systematic approach related to the fact that, at shallow depths, the stress and geologic conditions may be highly anisotropic. Due to the lack of data on the post-failure characteristics of the rock mass, the traditional Mohr-Coulomb yield criterion was assumed and used. The results clearly indicate that, as expected, the presence of the blast-induced damage zone does affect the behaviour of the boundary stresses and ground deformation. Potential failure types occurring around the tunnel boundary and their mechanisms have also been identified.

Rock History and Culture

OpenAIRE

Gonzalez, Éric

2013-01-01

Two ambitious works written by French-speaking scholars tackle rock music as a research object, from different but complementary perspectives. Both are a definite must-read for anyone interested in the contextualisation of rock music in western popular culture. In Une histoire musicale du rock (i.e. A Musical History of Rock), rock music is approached from the point of view of the people – musicians and industry – behind the music. Christophe Pirenne endeavours to examine that field from a m...

Effects of increased rock strata stresses on coal gettability

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Skoczynski, W [Politechnika Slaska, Gliwice (Poland). Instytut Mechanizacji Gornictwa

1988-01-01

Analyzes effects of rock strata pressure on a coal seam, its cracking and on energy consumption of coal cutting by shearer loaders and coal plows. Effects of mining depth on stresses in a coal seam rib side were analyzed using formulae developed by Budryk, Chudek and Borecki. Formulae used for selecting optimum yield strength of powered supports at working faces are reviewed. Four types of spontaneous separation of coal seam blocks caused by rock strata stresses are evaluated: layers parallel to the face with constant thickness, coal blocks with thickness decreasing in the direction of the floor or roof (blocks with a planar triangle cross-cut), blocks situated in the seam layer adjacent to the floor or roof. Causes of each type of coal seam separation are analyzed. 9 refs.

Controlled sample program publication No. 1: characterization of rock samples

International Nuclear Information System (INIS)

Ames, L.L.

1978-10-01

A description is presented of the methodology used and the geologic parameters measured on several rocks which are being used in round-robin laboratory and nuclide adsorption methodology experiments. Presently investigators from various laboratories are determining nuclide distribution coefficients utilizing numerous experimental techniques. Unfortunately, it appears that often the resultant data are dependent not only on the type of groundwater and rock utilized, but also on the experimentor or method used. The Controlled Sample Program is a WISAP (Waste Isolation Safety Assessment Program) attempt to resolve the apparent method and dependencies and to identify individual experimenter's bias. The rock samples characterized in an interlaboratory Kd methodology comparison program include Westerly granite, Argillaceous shale, Oolitic limestone, Sentinel Gap basalt, Conasauga shale, Climax Stock granite, anhydrite, Magenta dolomite and Culebra dolomite. Techniques used in the characterization include whole rock chemical analysis, X-ray diffraction, optical examination, electron microprobe elemental mapping, and chemical analysis of specific mineral phases. Surface areas were determined by the B.E.T. and ethylene glycol sorption methods. Cation exchange capacities were determined with 85 Sr, but were of questionable value for the high calcium rocks. A quantitative mineralogy was also estimated for each rock. Characteristics which have the potential of strongly affecting radionuclide Kd values such as the presence of sulfides, water-soluble, pH-buffering carbonates, glass, and ferrous iron were listed for each rock sample

Statistical fracture mechanics approach to the strength of brittle rock

International Nuclear Information System (INIS)

Ratigan, J.L.

1981-06-01

Statistical fracture mechanics concepts used in the past for rock are critically reviewed and modifications are proposed which are warranted by (1) increased understanding of fracture provided by modern fracture mechanics and (2) laboratory test data both from the literature and from this research. Over 600 direct and indirect tension tests have been performed on three different rock types; Stripa Granite, Sierra White Granite and Carrara Marble. In several instances assumptions which are common in the literature were found to be invalid. A three parameter statistical fracture mechanics model with Mode I critical strain energy release rate as the variant is presented. Methodologies for evaluating the parameters in this model as well as the more commonly employed two parameter models are discussed. The experimental results and analysis of this research indicate that surfacially distributed flaws, rather than volumetrically distributed flaws are responsible for rupture in many testing situations. For several of the rock types tested, anisotropy (both in apparent tensile strength and size effect) precludes the use of contemporary statistical fracture mechanics models

Proceedings of a technical session on rock mechanics ''Advance in laboratory sample testing''

International Nuclear Information System (INIS)

Come, B.

1984-01-01

This report brings together a series of papers about rock mechanics. The meeting was divided into three sessions, which dealt with the three main types of rock formation currently considered in the CEC Programme: granite, clay and salt. Safe disposal of high-level radioactive waste involves the proper design of deep underground repositories. This necessitates an in-depth knowledge of the mechanical properties of the rock mass. The behaviour of the rock mass must be known both for the construction and the operation (heating effects) of the repository. Usually, the dominant factor for designing an underground structure is the fracturing of the rock mass. In the present case, the rock is chosen with a very low fracturing. Therefore, the mechanical properties of the formation are mainly those of the rock matrix. These properties are obtained, at least in a first exploratory step, by laboratory testing of rock samples obtained by core-drilling from surface. This aspect of rock characterization was thought to deserve a special technical meeting, in order to bring together most of the results obtained in this field by contracting partners of the CEC for the years 1980-82

Comparative geology and geochemistry of sedimentary-rock-hosted (Carlin Type) gold deposits in the People's Republic of China and in Nevada, USA

Science.gov (United States)

Li, Zhiping; Peters, Stephen G.

1998-01-01

Sedimentary-rock-hosted (Carlin-type) gold deposits have been considered economically significant and geologically distinct since the early 1960's. This report consists of a nine-part text and an interactive database. This small database is to help Western companies get more information about these gold deposits in China, and to help geologists who are interested in world Carlin-type deposits conduct research on them. Because of their economic significance and geological distinctiveness, these deposits have caught the interest of economic geologists all over the world since the early 1960's. Similar deposits have been discovered in China, Australia, Dominican Republic, Spain, and Russia besides Nevada. Perhaps most significant are the 165 Carlin-type gold deposits that were found in southwest China during the past 15 years. Of these, at least 19 deposits have proven to be of substantial tonnage, making China the second leading country to exploit such deposits. With the increasing interest in Chinese Carlin-type gold deposits, some western companies and geologists desire to get more information about these Chinese deposits. This seems to have been very difficult because the literature was in Chinese. It is estimated that several hundred scientific publications (including papers, books, and technical reports) have been published. This database of Chinese Carlin-type Gold deposits is built on the documentation published during the most recent 10 years and includes six subjects, which consist of 165 records and 30 fields. A new Proterozoic-age sedimentary-rock-hosted gold deposit in northeastern P.R. China also is described. Note that for the old version 1.1 on the CD-ROM, the latitude and longitude locations of the mineral occurrences have been estimated from sketch maps and journal articles and are not intended for digital analysis. One of the improvements in this version 1.2 is the accuracy of geographic data. Version 1.3 updates to the database and includes maps

ROCK inhibition as a therapy for spinal muscular atrophy: understanding the repercussions on multiple cellular targets

Directory of Open Access Journals (Sweden)

Emmanuelle eCoque

2014-08-01

Full Text Available Spinal muscular atrophy (SMA is the most common genetic disease causing infant death, due to an extended loss of motoneurons. This neuromuscular disorder results from deletions and/or mutations within the surviving motor neuron 1 (SMN1 gene, leading to a pathological decreased expression of functional full-length SMN protein. Emerging studies suggest that the small GTPase RhoA and its major downstream effector Rho kinase (ROCK, which both play an instrumental role in cytoskeleton organization, contribute to the pathology of motoneuron diseases. Indeed, an enhanced activation of RhoA and ROCK has been reported in the spinal cord of an SMA mouse model. Moreover, the treatment of SMA mice with ROCK inhibitors leads to an increased lifespan as well as improved skeletal muscle and neuromuscular junction pathology, without preventing motoneuron degeneration. Although motoneurons are the primary target in SMA, an increasing number of reports show that other cell types inside and outside the central nervous system contribute to SMA pathogenesis. As administration of ROCK inhibitors to SMA mice was systemic, the improvement in survival and phenotype could therefore be attributed to specific effects on motoneurons and/or on other non-neuronal cell types. In the present review, we will present the various roles of the RhoA/ROCK pathway in several SMA cellular targets including neurons, myocytes, glial cells, cardiomyocytes and pancreatic cells as well as discuss how ROCK inhibition may ameliorate their health and function. It is most likely a concerted influence of ROCK modulation on all these cell types that ultimately lead to the observed benefits of pharmacological ROCK inhibition in SMA mice.

ROCK inhibition as a therapy for spinal muscular atrophy: understanding the repercussions on multiple cellular targets

Science.gov (United States)

Coque, Emmanuelle; Raoul, Cédric; Bowerman, Mélissa

2014-01-01

Spinal muscular atrophy (SMA) is the most common genetic disease causing infant death, due to an extended loss of motoneurons. This neuromuscular disorder results from deletions and/or mutations within the Survival Motor Neuron 1 (SMN1) gene, leading to a pathological decreased expression of functional full-length SMN protein. Emerging studies suggest that the small GTPase RhoA and its major downstream effector Rho kinase (ROCK), which both play an instrumental role in cytoskeleton organization, contribute to the pathology of motoneuron diseases. Indeed, an enhanced activation of RhoA and ROCK has been reported in the spinal cord of an SMA mouse model. Moreover, the treatment of SMA mice with ROCK inhibitors leads to an increased lifespan as well as improved skeletal muscle and neuromuscular junction pathology, without preventing motoneuron degeneration. Although motoneurons are the primary target in SMA, an increasing number of reports show that other cell types inside and outside the central nervous system contribute to SMA pathogenesis. As administration of ROCK inhibitors to SMA mice was systemic, the improvement in survival and phenotype could therefore be attributed to specific effects on motoneurons and/or on other non-neuronal cell types. In the present review, we will present the various roles of the RhoA/ROCK pathway in several SMA cellular targets including neurons, myoblasts, glial cells, cardiomyocytes and pancreatic cells as well as discuss how ROCK inhibition may ameliorate their health and function. It is most likely a concerted influence of ROCK modulation on all these cell types that ultimately lead to the observed benefits of pharmacological ROCK inhibition in SMA mice. PMID:25221469

Comparison of Crack Initiation, Propagation and Coalescence Behavior of Concrete and Rock Materials

Science.gov (United States)

Zengin, Enes; Abiddin Erguler, Zeynal

2017-04-01

There are many previously studies carried out to identify crack initiation, propagation and coalescence behavior of different type of rocks. Most of these studies aimed to understand and predict the probable instabilities on different engineering structures such as mining galleries or tunnels. For this purpose, in these studies relatively smaller natural rock and synthetic rock-like models were prepared and then the required laboratory tests were performed to obtain their strength parameters. By using results provided from these models, researchers predicted the rock mass behavior under different conditions. However, in the most of these studies, rock materials and models were considered as contains none or very few discontinuities and structural flaws. It is well known that rock masses naturally are extremely complex with respect to their discontinuities conditions and thus it is sometimes very difficult to understand and model their physical and mechanical behavior. In addition, some vuggy rock materials such as basalts and limestones also contain voids and gaps having various geometric properties. Providing that the failure behavior of these type of rocks controlled by the crack initiation, propagation and coalescence formed from their natural voids and gaps, the effect of these voids and gaps over failure behavior of rocks should be investigated. Intact rocks are generally preferred due to relatively easy side of their homogeneous characteristics in numerical modelling phases. However, it is very hard to extract intact samples from vuggy rocks because of their complex pore sizes and distributions. In this study, the feasibility of concrete samples to model and mimic the failure behavior vuggy rocks was investigated. For this purpose, concrete samples were prepared at a mixture of %65 cement dust and %35 water and their physical and mechanical properties were determined by laboratory experiments. The obtained physical and mechanical properties were used to

Potential climatic refugia in semi-arid, temperate mountains: plant and arthropod assemblages associated with rock glaciers, talus slopes, and their forefield wetlands, Sierra Nevada, California, USA

Science.gov (United States)

Constance I. Millar; Robert D. Westfall; Angela Evenden; Jeffrey G. Holmquist; Jutta Schmidt-Gengenbach; Rebecca S. Franklin; Jan Nachlinger; Diane L. Delany

2015-01-01

Unique thermal and hydrologic regimes of rock-glacier and periglacial talus environments support little-studied mountain ecosystems. We report the first studies of vascular plant and arthropod diversity for these habitats in the central Sierra Nevada, California, USA. Surfaces of active rock glaciers develop scattered islands of soil that provide habitat for vegetation...

The potassic sedimentary rocks in Gale Crater, Mars, as seen by ChemCam Onboard Curiosity

Science.gov (United States)

Le Deit, Laetitia; Mangold, Nicolas; Forni, Olivier; Cousin, Agnes; Lasue, Jeremie; Schröder, Susanne; Wiens, Roger C.; Sumner, Dawn Y.; Fabre, Cecile; Stack, Katherine M.; Anderson, Ryan; Blaney, Diana L.; Clegg, Samuel M.; Dromart, Gilles; Fisk, Martin; Gasnault, Olivier; Grotzinger, John P.; Gupta, Sanjeev; Lanza, Nina; Le Mouélic, Stephane; Maurice, Sylvestre; McLennan, Scott M.; Meslin, Pierre-Yves; Nachon, Marion; Newsom, Horton E.; Payre, Valerie; Rapin, William; Rice, Melissa; Sautter, Violaine; Treiman, Alan H.

2016-01-01

The Mars Science Laboratory rover Curiosity encountered potassium-rich clastic sedimentary rocks at two sites in Gale Crater, the waypoints Cooperstown and Kimberley. These rocks include several distinct meters thick sedimentary outcrops ranging from fine sandstone to conglomerate, interpreted to record an ancient fluvial or fluvio-deltaic depositional system. From ChemCam Laser-Induced Breakdown Spectroscopy (LIBS) chemical analyses, this suite of sedimentary rocks has an overall mean K2O abundance that is more than 5 times higher than that of the average Martian crust. The combined analysis of ChemCam data with stratigraphic and geographic locations reveals that the mean K2O abundance increases upward through the stratigraphic section. Chemical analyses across each unit can be represented as mixtures of several distinct chemical components, i.e., mineral phases, including K-bearing minerals, mafic silicates, Fe-oxides, and Fe-hydroxide/oxyhydroxides. Possible K-bearing minerals include alkali feldspar (including anorthoclase and sanidine) and K-bearing phyllosilicate such as illite. Mixtures of different source rocks, including a potassium-rich rock located on the rim and walls of Gale Crater, are the likely origin of observed chemical variations within each unit. Physical sorting may have also played a role in the enrichment in K in the Kimberley formation. The occurrence of these potassic sedimentary rocks provides additional evidence for the chemical diversity of the crust exposed at Gale Crater.

Diversity at Work.

Science.gov (United States)

Sabo, Sandra R.

2000-01-01

Diversity in the workplace goes beyond racial, ethnic, and cultural backgrounds. It extends to those with disabilities of all types and older workers. Students must be able to acknowledge and appreciate peoples' differences and educators must integrate diversity into the classroom. (JOW)

Magmatic and Crustal Differentiation History of Granitic Rocks from Hf-O Isotopes in Zircon

Science.gov (United States)

Kemp, , A. I. S.; Hawkesworth, , C. J.; Foster, , G. L.; Paterson, , B. A.; Woodhead, , J. D.; Hergt, , J. M.; Gray, , C. M.; Whitehouse, M. J.

2007-02-01

Granitic plutonism is the principal agent of crustal differentiation, but linking granite emplacement to crust formation requires knowledge of the magmatic evolution, which is notoriously difficult to reconstruct from bulk rock compositions. We unlocked the plutonic archive through hafnium (Hf) and oxygen (O) isotope analysis of zoned zircon crystals from the classic hornblende-bearing (I-type) granites of eastern Australia. This granite type forms by the reworking of sedimentary materials by mantle-like magmas instead of by remelting ancient metamorphosed igneous rocks as widely believed. I-type magmatism thus drives the coupled growth and differentiation of continental crust.

Sampling and treatment of rock cores and groundwater under reducing environments of deep underground

International Nuclear Information System (INIS)

Ebashi, Katsuhiro; Yamaguchi, Tetsuji; Tanaka, Tadao

2005-01-01

A method of sampling and treatment of undisturbed rock cores and groundwater under maintained reducing environments of deep underground was developed and demonstrated in a Neogene's sandy mudstone layer at depth of GL-100 to -200 m. Undisturbed rock cores and groundwater were sampled and transferred into an Ar gas atmospheric glove box with minimized exposure to the atmosphere. The reducing conditions of the sampled groundwater and rock cores were examined in the Ar atmospheric glove box by measuring pH and Eh of the sampled groundwater and sampled groundwater contacting with disk type rock samples, respectively. (author)

Rapid formation of rock armour for soil - rock fragment mixture during simulated rainfall

Science.gov (United States)

Poultney, E.; McGrath, G. S.; Hinz, C.

2009-04-01

Preventing erosion is an important issue in disturbed semi-arid and arid landscapes. This is in particular of highest importance for mining companies while undertaking land rehabilitation. An onsite investigation of the impact of surface rock fragments on erosion was conducted at Telfer goldmine in the Great Sandy Desert, Western Australia. The study site is a waste rock dump designed to mimic the concave slope of a natural mesa to both discourage erosion and blend in with its natural surroundings. Four treatments were used to construct the slope: two are topsoil mixed with rock fragments, and two are unmixed topsoil. A field study investigating erosion rills, particle size distribution, rock fragment coverage surface roughness and vegetation was carried out to determine changes down and across slope. The treatments constructed by mixing topsoil and rock fragments are more stable and show rock fragment distributions that more closely resemble patterns found on natural mesas surrounding Telfer. A controlled study using trays of topsoil mixed with rock fragment volumes of 50%, 60%, 70% and 80% were used to investigate how varying mixtures of rock fragments and topsoil erode using rainfall intensities between 20 and 100 mm h-1. Two runs of 25 minutes each were used to assess the temporal evolution of rock armouring. Surface coverage results converged for the 50%, 60% and 70% mixtures after the first run to coverage of about 90%, suggesting that fine sediment proportion does not affect rate and degree of rock armouring.

Dependence of frictional strength on compositional variations of Hayward fault rock gouges

Science.gov (United States)

Morrow, Carolyn A.; Moore, Diane E.; Lockner, David A.

2010-01-01

The northern termination of the locked portion of the Hayward Fault near Berkeley, California, is found to coincide with the transition from strong Franciscan metagraywacke to melange on the western side of the fault. Both of these units are juxtaposed with various serpentinite, gabbro and graywacke units to the east, suggesting that the gouges formed within the Hayward Fault zone may vary widely due to the mixing of adjacent rock units and that the mechanical behavior of the fault would be best modeled by determining the frictional properties of mixtures of the principal rock types. To this end, room temperature, water-saturated, triaxial shearing tests were conducted on binary and ternary mixtures of fine-grained gouges prepared from serpentinite and gabbro from the Coast Range Ophiolite, a Great Valley Sequence graywacke, and three different Franciscan Complex metasedimentary rocks. Friction coefficients ranged from 0.36 for the serpentinite to 0.84 for the gabbro, with four of the rock types having coefficients of friction ranging from 0.67-0.84. The friction coefficients of the mixtures can be predicted reliably by a simple weighted average of the end-member dry-weight percentages and strengths for all samples except those containing serpentinite. For the serpentinite mixtures, a linear trend between end-member values slightly overestimates the coefficients of friction in the midcomposition ranges. The range in strength for these rock admixtures suggests that both theoretical and numerical modeling of the fault should attempt to account for variations in rock and gouge properties.

Development of artificial soft rock

International Nuclear Information System (INIS)

Kishi, Kiyoshi

1995-01-01

When foundation base rocks are deeper than the level of installing structures or there exist weathered rocks and crushed rocks in a part of base rocks, often sound artificial base rocks are made by substituting the part with concrete. But in the construction of Kashiwazaki Kariwa Nuclear Power Station of Tokyo Electric Power Co., Inc., the foundation base rocks consist of mudstone, and the stiffness of concrete is large as compared with the surrounding base rocks. As the quality of the substituting material, the nearly same stiffness as that of the surrounding soft rocks and long term stability are suitable, and the excellent workability and economical efficiency are required, therefore, artificial soft rocks were developed. As the substituting material, the soil mortar that can obtain the physical property values in stable form, which are similar to those of Nishiyama mudstone, was selected. The mechanism of its hardening and the long term stability, and the manufacturing plant are reported. As for its application to the base rocks of Kashiwazaki Kariwa Nuclear Power Station, the verification test at the site and the application to the base rocks for No. 7 plant reactor building and other places are described. (K.I.)

On the use of High-density rock in rubble Mound Breakwaters

DEFF Research Database (Denmark)

Helgason, Einar; Burcharth, H. F.

2005-01-01

Natural rock with high density is widely used in the Scandinavian countries. However, the use of natural rock with density higher than 2:9t=m3 is ordinarily associated with some kind of problem solving, e.g. where normal density stones have to be replaced with heavier stones without increasing th...... on stability from the increased density is overestimated by conventional armour stability formulae in case of steep slopes. The infuence of the density depends on the slope angle and the type of armour units....... the construction volume or layer thickness. Most common design formulae do not give a clear conclusion on the in°uence of the rock density on the stability. The present paper presents results of small and large scale model tests in which is used rock with different densities. It is shown that the positive effect...

Rock Rb-Sr ages from Bananal region - Sao Paulo State, Brazil

International Nuclear Information System (INIS)

Dias Neto, C.M.; Tassinari, C.G.C.; Silva, M.E.

1996-01-01

New Rb-Sr whole rock isochron ages have been determined for the main lithological units that occur in Sao Paulo and Rio de Janeiro States. These rocks belong to Serra do Mar domain. The purpose of this work is to characterize the sequence of the geological events as well as the possible relationship between the different rocks. The geochronological data suggest that the paragneisses and the basement rocks, represented by ortho gneisses nuclei, were generated under amphibolite conditions around 700 Ma. At the same time the leucogranites were generated by partial melting processes and injected into both gneiss types. Tarditectonic granitic magmatic activities took place within ductile shear zones. One of the granites, the Getulandia granite, yielded an age of 514 Ma, falling in the range of the late Brasiliano Cycle which extended into the Middle Cambrian. (author). 9 figs., 1 tab

Thallium and its contents in Remata carbonate rocks

Directory of Open Access Journals (Sweden)

Kondelová Marcela

1996-09-01

Full Text Available The article presents at first the list of thallium own minerals and its isomorphic content in other minerals, especially in Slovakian ore deposits. This trace element was found in numerous dolomite-rock samples from Remata massif near Handlová. An interesting level of Tl content was analyzed in nonsilicified rocks; the highest content of Tl (and Ag are along the E – W line of disturbance. The presence of thallium in some limonitic aggregates in close Kremnica-gold deposit indicate any continuous relation. Some similarities to type gold deposits Carlin ( USA are discussed, even if no gold and discrete thallium phases were in Remata determined yet.

Study of Post-Peak Strain Softening Mechanical Behaviour of Rock Material Based on Hoek–Brown Criterion

OpenAIRE

Qibin Lin; Ping Cao; Peixin Wang

2018-01-01

In order to build the post-peak strain softening model of rock, the evolution laws of rock parameters m,s were obtained by using the evolutionary mode of piecewise linear function regarding the maximum principle stress. Based on the nonlinear Hoek–Brown criterion, the analytical relationship of the rock strength parameters m,s, cohesion c, and friction angle φ has been developed by theoretical derivation. According to the analysis on the four different types of rock, it is found that, within ...

Incoherent SSI Analysis of Reactor Building using 2007 Hard-Rock Coherency Model

International Nuclear Information System (INIS)

Kang, Joo-Hyung; Lee, Sang-Hoon

2008-01-01

Many strong earthquake recordings show the response motions at building foundations to be less intense than the corresponding free-field motions. To account for these phenomena, the concept of spatial variation, or wave incoherence was introduced. Several approaches for its application to practical analysis and design as part of soil-structure interaction (SSI) effect have been developed. However, conventional wave incoherency models didn't reflect the characteristics of earthquake data from hard-rock site, and their application to the practical nuclear structures on the hard-rock sites was not justified sufficiently. This paper is focused on the response impact of hard-rock coherency model proposed in 2007 on the incoherent SSI analysis results of nuclear power plant (NPP) structure. A typical reactor building of pressurized water reactor (PWR) type NPP is modeled classified into surface and embedded foundations. The model is also assumed to be located on medium-hard rock and hard-rock sites. The SSI analysis results are obtained and compared in case of coherent and incoherent input motions. The structural responses considering rocking and torsion effects are also investigated

Uranium mineralization and unconformities: how do they correlate? - A look beyond the classic unconformity-type deposit model?

Science.gov (United States)

Markwitz, Vanessa; Porwal, Alok; Campbell McCuaig, T.; Kreuzer, Oliver P.

2010-05-01

Uranium deposits are usually classified based on the characteristics of their host rocks and geological environments (Dahlkamp, 1993; OECD/NEA Red Book and IAEA, 2000; Cuney, 2009). The traditional unconformity-related deposit types are the most economical deposits in the world, with the highest grades amongst all uranium deposit types. In order to predict undiscovered uranium deposits, there is a need to understand the spatial association of uranium mineralization with structures and unconformities. Hydrothermal uranium deposits develop by uranium enriched fluids from source rocks, transported along permeable pathways to their depositional environment. Unconformities are not only separating competent from incompetent sequences, but provide the physico-chemical gradient in the depositional environment. They acted as important fluid flow pathways for uranium to migrate not only for surface-derived oxygenated fluids, but also for high oxidized metamorphic and magmatic fluids, dominated by their geological environment in which the unconformities occur. We have carried out comprehensive empirical spatial analyses of various types of uranium deposits in Australia, and first results indicate that there is a strong spatial correlation between unconformities and uranium deposits, not only for traditional unconformity-related deposits but also for other styles. As a start we analysed uranium deposits in Queensland and in particular Proterozoic metasomatic-related deposits in the Mount Isa Inlier and Late Carboniferous to Early Permian volcanic-hosted uranium occurrences in Georgetown and Charters Towers Regions show strong spatial associations with contemporary and older unconformities. The Georgetown Inlier in northern Queensland consists of a diverse range of rocks, including Proterozoic and early Palaeozoic metamorphic rocks and granites and late Palaeozoic volcanic rocks and related granites. Uranium-molybdenum (+/- fluorine) mineralization in the Georgetown inlier

Teaching the Rock Cycle with Ease.

Science.gov (United States)

Bereki, Debra

2000-01-01

Describes a hands-on lesson for teaching high school students the concept of the rock cycle using sedimentary, metamorphic, and igneous rocks. Students use a rock cycle diagram to identify pairs of rocks. From the rock cycle, students explain on paper how their first rock became the second rock and vice versa. (PVD)

Recreating Rocks

DEFF Research Database (Denmark)

Posth, Nicole R

2008-01-01

Nicole Posth and colleagues spent a month touring South African rock formations in their quest to understand the origin of ancient iron and silicate layers.......Nicole Posth and colleagues spent a month touring South African rock formations in their quest to understand the origin of ancient iron and silicate layers....

Clay shale as host rock. A geomechanical contribution about Opalinus clay

International Nuclear Information System (INIS)

Lempp, Christof; Menezes, Flora; Sachwitz, Simon

2016-01-01

The Opalinuston is a prominent rock representing the type of organic clay shales or clay stones within the sequence of Triassic and Jurassic marine sediments in Southern Germany. The rock forms a homogenous unit some ten meters thick. The degree of consolidation of this type of pelitic rock depends mainly on the former load conditions, but is also dependent on the long-term weathering and even on the present exposition. The geomechanical parameters such as shear strength, tensional strength and permeability vary with the state of consolidation and become important when the use is discussed of such rocks for radioactive waste disposal. A tunneling project at the northern escarpment of the Swabian Alb (Southwest Germany) within the Opalinus clay offered the rare opportunity to obtain fresh unweathered rock samples in greater amounts compared to fresh drilling cores from which geomechanical investigations are usually undertaken. Consequently, the results of geomechanical laboratory testings are presented in order to compare here the results of multistep triaxial compression tests, of hydraulic fracturing laboratory tests and of some other tests for rock characterization with the corresponding results of Opalinus clay sites in Switzerland that were investigated by the Swiss Nagra Company for host rock characterization. After a discussion of the relevant state of fresh Opalinus clay, especially of suction pressure conditions and saturation state, the results of triaxial shear tests are presented. Increasing shear deformation at increasing pressure and unchanged water saturation do not result in a significant strength reduction of the Opalinus clay. The rock shows increasing cohesion and stiffness, if multiple loading has repeatedly reached the failure point. Thus there is no increased permeability with continued shearing. Only at the beginning of the shearing process is a temporarily increased permeability to be expected due to dilatation processes. An increased

Petroleum source-rock potentials of the cretaceous transgressive-regressive sedimentary sequences of the Cauvery Basin

Science.gov (United States)

Chandra, Kuldeep; Philip, P. C.; Sridharan, P.; Chopra, V. S.; Rao, Brahmaji; Saha, P. K.

The present work is an attempt to contribute to knowledge on the petroleum source-rock potentials of the marine claystones and shales of basins associated with passive continental margins where the source-rock developments are known to have been associated with the anoxic events in the Mesozoic era. Data on three key exploratory wells from three major depressions Ariyallur-Pondicherry, Thanjavur and Nagapattinam of the Cauvery Basin are described and discussed. The average total organic carbon contents of the transgressive Pre-Albian-Cinomanian and Coniacian/Santonian claystones/shales range from 1.44 and 1.16%, respectively. The transgressive/regressive Campanian/Maastrichtian claystones contain average total organic carbon varying from 0.62 to 1.19%. The kerogens in all the studied stratigraphic sequences are classified as type-III with Rock-Eval hydrogen indices varying from 30 to 275. The nearness of land masses to the depositional basin and the mainly clastic sedimentation resulted in accumulation and preservation of dominantly type-III kerogens. The Pre-Albian to Cinomanian sequences of peak transgressive zone deposited in deep marine environments have kerogens with a relatively greater proportion of type-II components with likely greater contribution of planktonic organic matters. The global anoxic event associated with the Albian-Cinomanian marine transgression, like in many other parts of the world, has pervaded the Cauvery Basin and favoured development of good source-rocks with type-III kerogens. The Coniacian-Campanian-Maastrichtian transgressive/regressive phase is identified to be relatively of lesser significance for development of good quality source-rocks.

Life on the rocks: Multilocus phylogeography of rock hyrax (Procavia capensis) from southern Africa.

Science.gov (United States)

Maswanganye, K Amanda; Cunningham, Michael J; Bennett, Nigel C; Chimimba, Christian T; Bloomer, Paulette

2017-09-01

Understanding the role of geography and climatic cycles in determining patterns of biodiversity is important in comparative and evolutionary biology and conservation. We studied the phylogeographic pattern and historical demography of a rock-dwelling small mammal species from southern Africa, the rock hyrax Procavia capensis capensis. Using a multilocus coalescent approach, we assessed the influence of strong habitat dependence and fluctuating regional climates on genetic diversity. We sequenced a mitochondrial gene (cytochrome b) and two nuclear introns (AP5, PRKC1) supplemented with microsatellite genotyping, in order to assess evolutionary processes over multiple temporal scales. In addition, distribution modelling was used to investigate the current and predicted distribution of the species under different climatic scenarios. Collectively, the data reveal a complex history of isolation followed by secondary contact shaping the current intraspecific diversity. The cyt b sequences confirmed the presence of two previously proposed geographically and genetically distinct lineages distributed across the southern African Great Escarpment and north-western mountain ranges. Molecular dating suggests Miocene divergence of the lineages, yet there are no discernible extrinsic barriers to gene flow. The nuclear markers reveal incomplete lineage sorting or ongoing mixing of the two lineages. Although the microsatellite data lend some support to the presence of two subpopulations, there is weak structuring within and between lineages. These data indicate the presence of gene flow from the northern into the southern parts of the southern African sub-region likely following the secondary contact. The distribution modelling predictably reveal the species' preference for rocky areas, with stable refugia through time in the northern mountain ranges, the Great Escarpment, as well as restricted areas of the Northern Cape Province and the Cape Fold Mountains of South Africa

Thermal properties of rock salt and quartz monzonite to 5730K and 50-MPa confining pressure

International Nuclear Information System (INIS)

Durham, W.B.; Abey, A.E.

1981-01-01

Measurements of thermal conductivity, thermal diffusivity, and thermal linear expansion have been made on two rock types, a rock salt and a quartz monzonite, at temperatures from 300 to 573 0 K and confining pressures from 10 to 50 MPa. The samples were taken from deep rock formations under consideration as possible sites for a nuclear waste repository - the rock salt from a domal salt formation at Avery Island, Louisiana, and the quartz monzonite from the Climax Stock, Nevada Test Site, Nevada. The testing temperature and pressures are meant to bracket conditions expected in the repository. In both rock types, the thermal properties show a strong dependence upon temperature and a weak or non-dependence upon confining pressure. Thermal conductivity and diffusivity both decrease with increasing temperature in approximately linear fashion for samples which have not been previously heated. At 50 MPa in both rocks this decrease closely matches the measured or expected intrinsic (crack-free) behavior of the material. Preliminary indications from the quartz monzonite suggest that conductivity and diffusivity at low pressure and temperature may decrease as a result of heat treatment above 400 0 K

ROCK-CAD - computer aided geological modelling system

International Nuclear Information System (INIS)

Saksa, P.

1995-12-01

The study discusses surface and solid modelling methods, their use and interfacing with geodata. Application software named ROCK-CAD suitable for geological bedrock modelling has been developed with support from Teollisuuden Voima Oy (TVO). It has been utilized in the Finnish site characterization programme for spent nuclear fuel waste disposal during the 1980s and 1990s. The system is based on the solid modelling technique. It comprises also rich functionality for the particular geological modelling scheme. The ROCK-CAD system provides, among other things, varying graphical vertical and horizontal intersections and perspective illustrations. The specially developed features are the application of the boundary representation modelling method, parametric object generation language and the discipline approach. The ROCK-CAD system has been utilized in modelling spatial distribution of rock types and fracturing structures in TVO's site characterization. The Olkiluoto site at Eurajoki serves as an example case. The study comprises the description of the modelling process, models and illustration examples. The utilization of bedrock models in site characterization, in tentative repository siting as well as in groundwater flow simulation is depicted. The application software has improved the assessment of the sites studied, given a new basis for the documentation of interpretation and modelling work, substituted hand-drawing and enabled digital transfer to numerical analysis. Finally, aspects of presentation graphics in geological modelling are considered. (84 refs., 30 figs., 11 tabs.)

Rock Goes to School on Screen: A Model for Teaching Non-"Learned" Musics Derived from the Films "School of Rock" (2003) and "Rock School" (2005)

Science.gov (United States)

Webb, Michael

2007-01-01

What can be learned from two films with "rock" and "school" in their titles, about rock in school and about music and schooling more broadly? "School of Rock" (2003), a "family comedy," and "Rock School" (2005), a documentary, provoke a range of questions, ideological and otherwise, surrounding the inclusion of rock in formal instructional…

Evaluating Re-Os systematics in organic-rich sedimentary rocks in response to petroleum generation using hydrous pyrolysis experiments

Science.gov (United States)

Rooney, A.D.; Selby, D.; Lewan, M.D.; Lillis, P.G.; Houzay, J.-P.

2012-01-01

Successful application of the 187Re–187Os geochronometer has enabled the determination of accurate and precise depositional ages for organic-rich sedimentary rocks (ORS) as well as establishing timing constraints of petroleum generation. However, we do not fully understand the systematics and transfer behaviour of Re and Os between ORS and petroleum products (e.g., bitumen and oil). To more fully understand the behaviour of Re–Os systematics in both source rocks and petroleum products we apply hydrous pyrolysis to two immature hydrocarbon source rocks: the Permian Phosphoria Formation (TOC = 17.4%; Type II-S kerogen) and the Jurassic Staffin Formation (TOC = 2.5%; Type III kerogen). The laboratory-based hydrous pyrolysis experiments were carried out for 72 h at 250, 300, 325 and 350 °C. These experiments provided us with whole rock, extracted rock and bitumen and in some cases expelled oil and asphaltene for evaluation of Re–Os isotopic and elemental abundance. The data from these experiments demonstrate that the majority (>95%) of Re and Os are housed within extracted rock and that thermal maturation does not result in significant transfer of Re or Os from the extracted rock into organic phases. Based on existing thermodynamic data our findings suggest that organic chelating sites have a greater affinity for the quadravalent states of Re and Os than sulphides. Across the temperature range of the hydrous pyrolysis experiments both whole rock and extracted rock 187Re/188Os ratios show small variations (3.3% and 4.7%, for Staffin, respectively and 6.3% and 4.9% for Phosphoria, respectively). Similarly, the 187Os/188Os ratios show only minor variations for the Staffin and Phosphoria whole rock and extracted rock samples (0.6% and 1.4% and 1.3% and 2.2%). These isotopic data strongly suggest that crude oil generation through hydrous pyrolysis experiments does not disturb the Re–Os systematics in ORS as supported by various studies on natural systems. The

A sampling study on rock properties affecting drilling rate index (DRI)

Science.gov (United States)

Yenice, Hayati; Özdoğan, Mehmet V.; Özfırat, M. Kemal

2018-05-01

Drilling rate index (DRI) developed in Norway is a very useful index in determining the drillability of rocks and even in performance prediction of hard rock TBMs and it requires special laboratory test equipment. Drillability is one of the most important subjects in rock excavation. However, determining drillability index from physical and mechanical properties of rocks is very important for practicing engineers such as underground excavation, drilling operations in open pit mining, underground mining and natural stone production. That is why many researchers have studied concerned with drillability to find the correlations between drilling rate index (DRI) and penetration rate, influence of geological properties on drillability prediction in tunneling, correlations between rock properties and drillability. In this study, the relationships between drilling rate index (DRI) and some physico-mechanical properties (Density, Shore hardness, uniaxial compressive strength (UCS, σc), Indirect tensile strength (ITS, σt)) of three different rock groups including magmatic, sedimentary and metamorphic were evaluated using both simple and multiple regression analysis. This study reveals the effects of rock properties on DRI according to different types of rocks. In simple regression, quite high correlations were found between DRI and uniaxial compressive strength (UCS) and also between DRI and indirect tensile strength (ITS) values. Multiple regression analyses revealed even higher correlations when compared to simple regression. Especially, UCS, ITS, Shore hardness (SH) and the interactions between them were found to be very effective on DRI values.

Hydrological-niche models predict water plant functional group distributions in diverse wetland types.

Science.gov (United States)

Deane, David C; Nicol, Jason M; Gehrig, Susan L; Harding, Claire; Aldridge, Kane T; Goodman, Abigail M; Brookes, Justin D

2017-06-01

Human use of water resources threatens environmental water supplies. If resource managers are to develop policies that avoid unacceptable ecological impacts, some means to predict ecosystem response to changes in water availability is necessary. This is difficult to achieve at spatial scales relevant for water resource management because of the high natural variability in ecosystem hydrology and ecology. Water plant functional groups classify species with similar hydrological niche preferences together, allowing a qualitative means to generalize community responses to changes in hydrology. We tested the potential for functional groups in making quantitative prediction of water plant functional group distributions across diverse wetland types over a large geographical extent. We sampled wetlands covering a broad range of hydrogeomorphic and salinity conditions in South Australia, collecting both hydrological and floristic data from 687 quadrats across 28 wetland hydrological gradients. We built hydrological-niche models for eight water plant functional groups using a range of candidate models combining different surface inundation metrics. We then tested the predictive performance of top-ranked individual and averaged models for each functional group. Cross validation showed that models achieved acceptable predictive performance, with correct classification rates in the range 0.68-0.95. Model predictions can be made at any spatial scale that hydrological data are available and could be implemented in a geographical information system. We show the response of water plant functional groups to inundation is consistent enough across diverse wetland types to quantify the probability of hydrological impacts over regional spatial scales. © 2017 by the Ecological Society of America.

Grinding into Soft, Powdery Rock

Science.gov (United States)

2004-01-01

This hole in a rock dubbed 'Clovis' is the deepest hole drilled so far in any rock on Mars. NASA's Mars Exploration Rover Spirit captured this view with its microscopic imager on martian sol 217 (Aug. 12, 2004) after drilling 8.9 millimeters (0.35 inch) into the rock with its rock abrasion tool. The view is a mosaic of four frames taken by the microscopic imager. The hole is 4.5 centimeters (1.8 inches) in diameter. Clovis is key to a developing story about environmental change on Mars, not only because it is among the softest rocks encountered so far in Gusev Crater, but also because it contains mineral alterations that extend relatively deep beneath its surface. In fact, as evidenced by its fairly crumbly texture, it is possibly the most highly altered volcanic rock ever studied on Mars. Scientific analysis shows that the rock contains higher levels of the elements sulfur, chlorine, and bromine than are normally encountered in basaltic rocks, such as a rock dubbed 'Humphrey' that Spirit encountered two months after arriving on Mars. Humphrey showed elevated levels of sulfur, chlorine, and bromine only in the outermost 2 millimeters (less than 0.1 inch) of its surface. Clovis shows elevated levels of the same elements along with the associated softness of the rock within a borehole that is 4 times as deep. Scientists hope to compare Clovis to other, less-altered rocks in the vicinity to assess what sort of water-based processes altered the rock. Hypotheses include transport of sulfur, chlorine, and bromine in water vapor in volcanic gases; hydrothermal circulation (flow of volcanically heated water through rock); or saturation in a briny soup containing the same elements. In this image, very fine-grained material from the rock has clumped together by electrostatic attraction and fallen into the borehole. NASA/JPL/Cornell/USGS

Boring and Sealing Rock with Directed Energy Millimeter-Waves

Science.gov (United States)

Woskov, P.; Einstein, H. H.; Oglesby, K.

2015-12-01

Millimeter-wave directed energy is being investigated to penetrate into deep crystalline basement rock formations to lower well costs and to melt rocks, metals, and other additives to seal wells for applications that include nuclear waste storage and geothermal energy. Laboratory tests have established that intense millimeter-wave (MMW) beams > 1 kW/cm2 can melt and/ or vaporize hard crystalline rocks. In principle this will make it possible to create open boreholes and a method to seal them with a glass/ceramic liner and plug formed from the original rock or with other materials. A 10 kW, 28 GHz commercial (CPI) gyrotron system with a launched beam diameter of about 32 mm was used to heat basalt, granite, limestone, and sandstone specimens to temperatures over 2500 °C to create melts and holes. A calibrated 137 GHz radiometer view, collinear with the heating beam, monitored real time peak rock temperature. A water load surrounding the rock test specimen primarily monitored unabsorbed power at 28 GHz. Power balance analysis of the laboratory observations shows that the temperature rise is limited by radiative heat loss, which would be expected to be trapped in a borehole. The analysis also indicates that the emissivity (absorption efficiency) in the radiated infrared range is lower than the emissivity at 28 GHz, giving the MMW frequency range an important advantage for rock melting. Strength tests on one granite type indicated that heating the rock initially weakens it, but with exposure to higher temperatures the resolidified black glassy product regains strength. Basalt was the easiest to melt and penetrate, if a melt leak path was provided, because of its low viscosity. Full beam holes up to about 50 mm diameter (diffraction increased beam size) were achieved through 30 mm thick basalt and granite specimens. Laboratory experiments to form a seal in an existing hole have also been carried out by melting rock and a simulated steel casing.

Sorption data bases for generic Swiss argillaceous rock systems

International Nuclear Information System (INIS)

Bradbury, M. H.; Baeyens, B.; Thoenen, T.

2010-09-01

In Switzerland the site selection procedure for both high level waste (HLW) and low and intermediate level waste (L/ILW) repositories is specified by the Swiss Federal Office of Energy in the Sectoral Plan for Deep Geological Repositories. In the forthcoming stage 2 of this plan, potential sites will be identified within regions previously selected based on the presence of suitable host rocks, namely Opalinus Clay, 'Brauner Dogger', Effingen Member and Helvetic Marl. Preliminary safety analyses are an integral part of this procedure, and require, amongst other information, the radionuclide sorption properties of the host rock. This report describes a methodology to develop a Generic Rock Sorption Data Base (GR-SDB) for argillaceous rocks. The method will be used to compile specific SDBs for the above mentioned host rocks. Arguments are presented that the main factor influencing sorption on argillaceous rocks is the phyllosilicate mineral content. These minerals are particularly effective at binding metals to their surfaces by cation exchange and surface complexation. Generally, the magnitude of sorption is directly correlated with the phyllosilicate content (2:1 type clays: illite/smectite/illitesmectite mixed layers), and this parameter best reflects the sorption potential of a given mineral assembly. Consequently, sorption measurements on illite were preferably used as source data for the GR-SDB. The second component influencing radionuclide sorption is the porewater chemistry. In the present report, generic water compositions were extracted from the analytical ranges of deep ground waters in various sedimentary formations in Switzerland. In order to cover the range of ionic strength (I) and pH values of Swiss ground waters in argillaceous rocks, five types of generic water compositions were defined, combining low, intermediate and high values of ionic strength and pH. The GR-SDB for in situ conditions was derived using conversion factors (CF). As the name

ROCK inhibitor prevents the dedifferentiation of human articular chondrocytes

International Nuclear Information System (INIS)

Matsumoto, Emi; Furumatsu, Takayuki; Kanazawa, Tomoko; Tamura, Masanori; Ozaki, Toshifumi

2012-01-01

Highlights: ► ROCK inhibitor stimulates chondrogenic gene expression of articular chondrocytes. ► ROCK inhibitor prevents the dedifferentiation of monolayer-cultured chondrocytes. ► ROCK inhibitor enhances the redifferentiation of cultured chondrocytes. ► ROCK inhibitor is useful for preparation of un-dedifferentiated chondrocytes. ► ROCK inhibitor may be a useful reagent for chondrocyte-based regeneration therapy. -- Abstract: Chondrocytes lose their chondrocytic phenotypes in vitro. The Rho family GTPase ROCK, involved in organizing the actin cytoskeleton, modulates the differentiation status of chondrocytic cells. However, the optimum method to prepare a large number of un-dedifferentiated chondrocytes is still unclear. In this study, we investigated the effect of ROCK inhibitor (ROCKi) on the chondrogenic property of monolayer-cultured articular chondrocytes. Human articular chondrocytes were subcultured in the presence or absence of ROCKi (Y-27632). The expression of chondrocytic marker genes such as SOX9 and COL2A1 was assessed by quantitative real-time PCR analysis. Cellular morphology and viability were evaluated. Chondrogenic redifferentiation potential was examined by a pellet culture procedure. The expression level of SOX9 and COL2A1 was higher in ROCKi-treated chondrocytes than in untreated cells. Chondrocyte morphology varied from a spreading form to a round shape in a ROCKi-dependent manner. In addition, ROCKi treatment stimulated the proliferation of chondrocytes. The deposition of safranin O-stained proteoglycans and type II collagen was highly detected in chondrogenic pellets derived from ROCKi-pretreated chondrocytes. Our results suggest that ROCKi prevents the dedifferentiation of monolayer-cultured chondrocytes, and may be a useful reagent to maintain chondrocytic phenotypes in vitro for chondrocyte-based regeneration therapy.

Petrology, Magnetic susceptibility, Tectonic setting and mineralization associated with Plutonic and Volcanic Rocks, Eastern Bajestan and Taherabad, Iran

Directory of Open Access Journals (Sweden)

Malihe Ghoorchi

2009-09-01

Full Text Available Study area is located in district of Bajestan and Ferdows cities, NE of Iran. Structurally, this area is part of Lut block. The oldest exposed rocks, to the north of intrusive rocks and in Eastern Bajestan, are meta-chert, slate, quartzite, thin-bedded crystalline limestone and meta-argillite. The sedimentary units are: Sardar Formation (Carboniferous, Jamal Formation (Permian, Sorkh Shale and Shotori Formations (Triassic, carbonateous rocks (Cretaceous and lithostratigraphically equivalent to Kerman conglomerate (Cretaceous-Paleocene are exposed in this area. Based on relative age, magmatism in eastern Bajestan and Taherabad started after Late Cretaceous and it has been active and repeated during Tertiary time. At least, three episodes of volcanic activities are recognized in this area. The first stage was mainly volcanic flow with mafic composition and minor intermediate. The second episode was mainly intermediate in composition. The third stage was changed to acid-intermediate in composition. Since the plutonic rocks intruded the volcanic rocks, therefore they may be Oligo-Miocene age. Bajestan intrusive rocks are granite-granodiorite-quartz monzonite. Taherabad intrusive rocks are diorite-quartz diorite- monzonite-latite. Bajestan intrusive rocks are reduced type (ilmenite series and Taherabad intrusive rocks are oxidized type (magnetite series.Based on geochemical analysis including trace elements, REE and isotopic data, Bajestan intrusive rocks formed in continental collision zone and the magma has crustal origin. Taherabad intrusive rocks were formed in subduction zone and magma originated from oceanic crust. Taherabad intrusive rock has exploration potential for Cu-Au and pb.

Profiling bacterial diversity in a limestone cave of the western Loess Plateau of China