Real-time modeling and simulation of distribution feeder and distributed resources

Science.gov (United States)

Singh, Pawan

The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

Ada and its impact on the scientific user

International Nuclear Information System (INIS)

Marty, R.

1982-01-01

The Ada programming language is the result of a collective effort to design a common language for programming real-time systems. The design of Ada was initiated by the United States Department of Defense (DoD) in 1975. Ada combines facilities found in most classical languages like Fortran, PL/I, Pascal, and Basic together with many features formerly found only in experimental languages. It is argued that these features make Ada a very decent tool not only for writing real-time programs but also for the development of software in the scientific sector. (orig.)

An approach to a real-time distribution system

Science.gov (United States)

Kittle, Frank P., Jr.; Paddock, Eddie J.; Pocklington, Tony; Wang, Lui

1990-01-01

The requirements of a real-time data distribution system are to provide fast, reliable delivery of data from source to destination with little or no impact to the data source. In this particular case, the data sources are inside an operational environment, the Mission Control Center (MCC), and any workstation receiving data directly from the operational computer must conform to the software standards of the MCC. In order to supply data to development workstations outside of the MCC, it is necessary to use gateway computers that prevent unauthorized data transfer back to the operational computers. Many software programs produced on the development workstations are targeted for real-time operation. Therefore, these programs must migrate from the development workstation to the operational workstation. It is yet another requirement for the Data Distribution System to ensure smooth transition of the data interfaces for the application developers. A standard data interface model has already been set up for the operational environment, so the interface between the distribution system and the application software was developed to match that model as closely as possible. The system as a whole therefore allows the rapid development of real-time applications without impacting the data sources. In summary, this approach to a real-time data distribution system provides development users outside of the MCC with an interface to MCC real-time data sources. In addition, the data interface was developed with a flexible and portable software design. This design allows for the smooth transition of new real-time applications to the MCC operational environment.

A Distributed Computing Network for Real-Time Systems.

Science.gov (United States)

1980-11-03

7 ) AU2 o NAVA TUNDEWATER SY$TEMS CENTER NEWPORT RI F/G 9/2 UIS RIBUT E 0 COMPUTIN G N LTWORK FOR REAL - TIME SYSTEMS .(U) UASSIFIED NOV Al 6 1...MORAIS - UT 92 dLEVEL c A Distributed Computing Network for Real - Time Systems . 11 𔃺-1 Gordon E/Morson I7 y tm- ,r - t "en t As J 2 -p .. - 7 I’ cNaval...NUMBER TD 5932 / N 4. TITLE mand SubotI. S. TYPE OF REPORT & PERIOD COVERED A DISTRIBUTED COMPUTING NETWORK FOR REAL - TIME SYSTEMS 6. PERFORMING ORG

Real-time modeling of heat distributions

Science.gov (United States)

Hamann, Hendrik F.; Li, Hongfei; Yarlanki, Srinivas

2018-01-02

Techniques for real-time modeling temperature distributions based on streaming sensor data are provided. In one aspect, a method for creating a three-dimensional temperature distribution model for a room having a floor and a ceiling is provided. The method includes the following steps. A ceiling temperature distribution in the room is determined. A floor temperature distribution in the room is determined. An interpolation between the ceiling temperature distribution and the floor temperature distribution is used to obtain the three-dimensional temperature distribution model for the room.

Static Schedulers for Embedded Real-Time Systems

Science.gov (United States)

1989-12-01

Because of the need for having efficient scheduling algorithms in large scale real time systems , software engineers put a lot of effort on developing...provide static schedulers for he Embedded Real Time Systems with single processor using Ada programming language. The independent nonpreemptable...support the Computer Aided Rapid Prototyping for Embedded Real Time Systems so that we determine whether the system, as designed, meets the required

Processor tradeoffs in distributed real-time systems

Science.gov (United States)

Krishna, C. M.; Shin, Kang G.; Bhandari, Inderpal S.

1987-01-01

The problem of the optimization of the design of real-time distributed systems is examined with reference to a class of computer architectures similar to the continuously reconfigurable multiprocessor flight control system structure, CM2FCS. Particular attention is given to the impact of processor replacement and the burn-in time on the probability of dynamic failure and mean cost. The solution is obtained numerically and interpreted in the context of real-time applications.

Design a Fault Tolerance for Real Time Distributed System

OpenAIRE

Ban M. Khammas

2012-01-01

This paper designed a fault tolerance for soft real time distributed system (FTRTDS). This system is designed to be independently on specific mechanisms and facilities of the underlying real time distributed system. It is designed to be distributed on all the computers in the distributed system and controlled by a central unit.Besides gathering information about a target program spontaneously, it provides information about the target operating system and the target hardware in order to diagno...

MicROS-drt: supporting real-time and scalable data distribution in distributed robotic systems.

Science.gov (United States)

Ding, Bo; Wang, Huaimin; Fan, Zedong; Zhang, Pengfei; Liu, Hui

A primary requirement in distributed robotic software systems is the dissemination of data to all interested collaborative entities in a timely and scalable manner. However, providing such a service in a highly dynamic and resource-limited robotic environment is a challenging task, and existing robot software infrastructure has limitations in this aspect. This paper presents a novel robot software infrastructure, micROS-drt, which supports real-time and scalable data distribution. The solution is based on a loosely coupled data publish-subscribe model with the ability to support various time-related constraints. And to realize this model, a mature data distribution standard, the data distribution service for real-time systems (DDS), is adopted as the foundation of the transport layer of this software infrastructure. By elaborately adapting and encapsulating the capability of the underlying DDS middleware, micROS-drt can meet the requirement of real-time and scalable data distribution in distributed robotic systems. Evaluation results in terms of scalability, latency jitter and transport priority as well as the experiment on real robots validate the effectiveness of this work.

Ada 9X overview

Science.gov (United States)

Weller, David G.

1992-01-01

The current version of Ada has been an ANSI standard since 1983. In 1988, the Ada Joint Program Office was tasked with reevaluating the language and proposing changes to the standard. Since that time, the world has seen a tremendous explosion in object-oriented languages, as well as other growing fields such as distributed computing and support for very large software systems. The speaker will discuss new features being added to the next version of Ada, currently called Ada 9X, and what transition issues must be considered for current Ada projects.

Developing and Using Ada Parts in Real-Time Embedded Applications

Science.gov (United States)

1990-04-27

ARCHTECTURAL DESIGN Guideline #3-a: Avoid duplication of data types packages. Guideline #3-b: Minimize variant proliferation. Concentrate on developing a...of SOFTWARE REUSE DEVELOPING and USING ADA PARTS in RTE APPUCATIONS ARCHTECTURAL DESIGN Table 5-10 illustrates the use of this more strongly data typed

Real Time Emulation of Dynamic Tariff for Congestion Management in Distribution Networks

DEFF Research Database (Denmark)

Rasmussen, Theis Bo; Wu, Qiuwei; Huang, Shaojun

2016-01-01

This paper presents the real time evaluation of the dynamic tariff (DT) method for alleviating congestion in a distribution networks with high penetration of distributed energy resources (DERs). The DT method is implemented in a real time digital testing platform that emulates a real distribution...

Real Time Synchronization for Creativity in Distributed Innovation Teams

DEFF Research Database (Denmark)

Peitersen, Dennis Kjaersgaard; Dolog, Peter; Pedersen, Esben Staunsbjerg

2009-01-01

In this paper we introduce a synchronization approach for real time collaborative sketching for creativity in distributed innovation teams. We base our approach on reverse AJAX. This way we ensure scalable solution for real time drawing and sketching important in creativity settings....

Real-time Control Mediation in Agile Distributed Software Development

DEFF Research Database (Denmark)

Persson, John Stouby; Aaen, Ivan; Mathiassen, Lars

2008-01-01

Agile distributed environments pose particular challenges related to control of quality and collaboration in software development. Moreover, while face-to-face interaction is fundamental in agile development, distributed environments must rely extensively on mediated interactions. On this backdrop...... control was mediated over distance by technology through real-time exchanges. Contrary to previous research, the analysis suggests that both formal and informal elements of real-time mediated control were used; that evolving goals and adjustment of expectations were two of the main issues in real......-time mediated control exchanges; and, that the actors, despite distances in space and culture, developed a clan-like pattern mediated by technology to help control quality and collaboration in software development....

Transforming AdaPT to Ada

Science.gov (United States)

Goldsack, Stephen J.; Holzbach-Valero, A. A.; Waldrop, Raymond S.; Volz, Richard A.

1991-01-01

This paper describes how the main features of the proposed Ada language extensions intended to support distribution, and offered as possible solutions for Ada9X can be implemented by transformation into standard Ada83. We start by summarizing the features proposed in a paper (Gargaro et al, 1990) which constitutes the definition of the extensions. For convenience we have called the language in its modified form AdaPT which might be interpreted as Ada with partitions. These features were carefully chosen to provide support for the construction of executable modules for execution in nodes of a network of loosely coupled computers, but flexibly configurable for different network architectures and for recovery following failure, or adapting to mode changes. The intention in their design was to provide extensions which would not impact adversely on the normal use of Ada, and would fit well in style and feel with the existing standard. We begin by summarizing the features introduced in AdaPT.

A Comparison of Ada 83 and C++

Science.gov (United States)

1991-06-01

developing large, complex, software systems with long lifetimes. Those interviewed for this study who are familiar with both Ada and C++ believe that Ada is...with those who are familiar with both languages, there was a clear preference for using Ada for large complex systems with long lifetimes. These...University, December 1990 Additions by Nelson H. Weiderman, June 1991. Chile Empresa Nacional de Aeronautica (ENAER), real-time avionics system, Data

Real-time Trading Strategies for Proactive Distribution Company with Distributed Generation and Demand Response

DEFF Research Database (Denmark)

Wang, Qi

Distributed energy resources (DERs), such as distributed generation (DG) and demand response (DR), have been recognized worldwide as valuable resources. High integration of DG and DR in the distribution network inspires a potential deregulated environment for the distribution company (DISCO...... in the presented DL market and transact with TL real-time market. A one-leader multi-follower-type bi-level model is proposed to indicate the PDISCO's trading strategies. To participate in the TL real-time market, a methodology is presented to derive continuous bidding/offering strategies for a PDISCO. A bi...

A Metrics-Based Approach to Intrusion Detection System Evaluation for Distributed Real-Time Systems

Science.gov (United States)

2002-04-01

Based Approach to Intrusion Detection System Evaluation for Distributed Real - Time Systems Authors: G. A. Fink, B. L. Chappell, T. G. Turner, and...Distributed, Security. 1 Introduction Processing and cost requirements are driving future naval combat platforms to use distributed, real - time systems of...distributed, real - time systems . As these systems grow more complex, the timing requirements do not diminish; indeed, they may become more constrained

Ada Run Time Support Environments and a common APSE Interface Set. [Ada Programming Support Environment

Science.gov (United States)

Mckay, C. W.; Bown, R. L.

1985-01-01

The paper discusses the importance of linking Ada Run Time Support Environments to the Common Ada Programming Support Environment (APSE) Interface Set (CAIS). A non-stop network operating systems scenario is presented to serve as a forum for identifying the important issues. The network operating system exemplifies the issues involved in the NASA Space Station data management system.

A Formal Approach to Run-Time Evaluation of Real-Time Behaviour in Distributed Process Control Systems

DEFF Research Database (Denmark)

Kristensen, C.H.

This thesis advocates a formal approach to run-time evaluation of real-time behaviour in distributed process sontrol systems, motivated by a growing interest in applying the increasingly popular formal methods in the application area of distributed process control systems. We propose to evaluate...... because the real-time aspects of distributed process control systems are considered to be among the hardest and most interesting to handle....

AdaM: Adapting Multi-User Interfaces for Collaborative Environments in Real-Time

DEFF Research Database (Denmark)

Park, Seonwook; Gebhardt, Christoph; Rädle, Roman

2018-01-01

and rule-based solutions are tedious to create and do not scale to larger problems nor do they adapt to dynamic changes, such as users leaving or joining an activity. In this paper, we cast the problem of UI distribution as an assignment problem and propose to solve it using combinatorial optimization. We...... present a mixed integer programming formulation which allows real-time applications in dynamically changing collaborative settings. It optimizes the allocation of UI elements based on device capabilities, user roles, preferences, and access rights. We present a proof-of-concept designer-in-the-loop tool......Developing cross-device multi-user interfaces (UIs) is a challenging problem. There are numerous ways in which content and interactivity can be distributed. However, good solutions must consider multiple users, their roles, their preferences and access rights, as well as device capabilities. Manual...

Monitoring Distributed Real-Time Systems: A Survey and Future Directions

Science.gov (United States)

Goodloe, Alwyn E.; Pike, Lee

2010-01-01

Runtime monitors have been proposed as a means to increase the reliability of safety-critical systems. In particular, this report addresses runtime monitors for distributed hard real-time systems. This class of systems has had little attention from the monitoring community. The need for monitors is shown by discussing examples of avionic systems failure. We survey related work in the field of runtime monitoring. Several potential monitoring architectures for distributed real-time systems are presented along with a discussion of how they might be used to monitor properties of interest.

Real-Time Reactive Power Distribution in Microgrids by Dynamic Programing

DEFF Research Database (Denmark)

Levron, Yoash; Beck, Yuval; Katzir, Liran

2017-01-01

In this paper a new real-time optimization method for reactive power distribution in microgrids is proposed. The method enables location of a globally optimal distribution of reactive power under normal operating conditions. The method exploits the typical compact structure of microgrids to obtain...... combination of reactive powers, by means of dynamic programming. Since every single step involves a one-dimensional problem, the complexity of the solution is only linear with the number of clusters, and as a result, a globally optimal solution may be obtained in real time. The paper includes the results...

Real-Time Congestion Management in Distribution Networks by Flexible Demand Swap

DEFF Research Database (Denmark)

Huang, Shaojun; Wu, Qiuwei

2017-01-01

In addition to the day-ahead congestion management in distribution networks, the real-time congestion management is very important because many unforeseen events can occur at the real operation time, e.g. loss of generation of distributed energy resources (DERs) or inaccurate forecast of energy...... pumps (HPs) for real time congestion management. The swap method can maintain the power balance of the system and avoid the imbalance cost of activating the flexibility service. An algorithm for forming swaps through optimal power flow (OPF) and mixed integer linear programming (MILP) is proposed...... consumption or production. Flexibility service from demand will be a good option to solve the real-time congestions if the cost of activating the flexibility service is fully addressed. This paper proposes a new method, namely “swap”, to employ the flexibility service from electric vehicles (EVs) and heat...

Reflexive reasoning for distributed real-time systems

Science.gov (United States)

Goldstein, David

1994-01-01

This paper discusses the implementation and use of reflexive reasoning in real-time, distributed knowledge-based applications. Recently there has been a great deal of interest in agent-oriented systems. Implementing such systems implies a mechanism for sharing knowledge, goals and other state information among the agents. Our techniques facilitate an agent examining both state information about other agents and the parameters of the knowledge-based system shell implementing its reasoning algorithms. The shell implementing the reasoning is the Distributed Artificial Intelligence Toolkit, which is a derivative of CLIPS.

The Design of a Real-Time Distributed System

NARCIS (Netherlands)

Hertzberger, L.O.; Mullender, S.J.; Poletiek, G.; van Renesse, R.; Tanenbaum, A.S.; Tuynman, F.; Vermeulen, J.C.

1986-01-01

In modern physics experiments an increasing number and variety of programmable processors is used. As a consequence, a software environment is needed that provides an integrated approach to development, testing and use of real-time distributed software. This contribution is based on work being done

Experiences with Ada in an embedded system

Science.gov (United States)

Labaugh, Robert J.

1988-01-01

Recent experiences with using Ada in a real time environment are described. The application was the control system for an experimental robotic arm. The objectives of the effort were to experiment with developing embedded applications in Ada, evaluating the suitability of the language for the application, and determining the performance of the system. Additional objectives were to develop a control system based on the NASA/NBS Standard Reference Model for Telerobot Control System Architecture (NASREM) in Ada, and to experiment with the control laws and how to incorporate them into the NASREM architecture.

Towards Real-Time Distributed Planning in Multi-Robot Systems

KAUST Repository

Abdelkader, Mohamed

2018-01-01

of extensive information exchange (communication). The extensive communication between robots can result in decision delays because of which distributed architecture is often impractical for systems with strict real-time constraints, e.g. when decisions have

On Modelling Real-time and Security properties of Distributed Systems

NARCIS (Netherlands)

Corin, Ricardo; Etalle, Sandro; Hartel, Pieter H.; Mader, Angelika H.

2003-01-01

We discuss a simplified version of the timing attack to illustrate a connection between security and real-time properties of distributed systems. We suggest several avenues for further research on this and similar connections.

Optimization of Time-Partitions for Mixed-Criticality Real-Time Distributed Embedded Systems

DEFF Research Database (Denmark)

Tamas-Selicean, Domitian; Pop, Paul

2011-01-01

In this paper we are interested in mixed-criticality embedded real-time applications mapped on distributed heterogeneous architectures. The architecture provides both spatial and temporal partitioning, thus enforcing enough separation for the critical applications. With temporal partitioning, each...

DEALed : A tool suite for distributed real-time systems development

NARCIS (Netherlands)

Bolshakov, K.; Karpov, Y.; Sintotski, A.; Malyshkin, V.

1999-01-01

DEALed is a tool suite for development of distributed systems using DEAL language. DEAL is being developed at Eindhoven University of Technology as a part of DEDOS project. Area of application of the DEALed is the development of the distributed real- time safety-critical control systems.

The response time distribution in a real-time database with optimistic concurrency control

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1996-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction uses an equal number of

Design optimization of TTEthernet-based distributed real-time systems

DEFF Research Database (Denmark)

Tamas-Selicean, Domitian; Pop, Paul; Steiner, Wilfried

2015-01-01

Many safety-critical real-time applications are implemented using distributed architectures, composed of heterogeneous processing elements interconnected in a network. Our focus in this paper is on the TTEthernet protocol, a deterministic, synchronized and congestion-free network protocol based o...

Validation Support for Distributed Real-Time Embedded Systems in VDM++

DEFF Research Database (Denmark)

S. Fitzgerald, John; Gorm Larsen, Peter; Tjell, Simon

2007-01-01

We present a tool-supported approach to the validation of system-level timing properties in formal models of distributed real-time embedded systems. Our aim is to provide system architects with rapid feedback on the timing characteristics of alternative designs in the often volatile early stages ...

Software engineering aspects of real-time programming concepts

Science.gov (United States)

Schoitsch, Erwin

1986-08-01

Real-time programming is a discipline of great importance not only in process control, but also in fields like communication, office automation, interactive databases, interactive graphics and operating systems development. General concepts of concurrent programming and constructs for process-synchronization are discussed in detail. Tasking and synchronization concepts, methods of process communication, interrupt and timeout handling in systems based on semaphores, signals, conditional critical regions or on real-time languages like Concurrent PASCAL, MODULA, CHILL and ADA are explained and compared with each other. The second part deals with structuring and modularization of technical processes to build reliable and maintainable real time systems. Software-quality and software engineering aspects are considered throughout the paper.

An Embedded Rule-Based Diagnostic Expert System in Ada

Science.gov (United States)

Jones, Robert E.; Liberman, Eugene M.

1992-01-01

Ada is becoming an increasingly popular programming language for large Government-funded software projects. Ada with it portability, transportability, and maintainability lends itself well to today's complex programming environment. In addition, expert systems have also assumed a growing role in providing human-like reasoning capability expertise for computer systems. The integration is discussed of expert system technology with Ada programming language, especially a rule-based expert system using an ART-Ada (Automated Reasoning Tool for Ada) system shell. NASA Lewis was chosen as a beta test site for ART-Ada. The test was conducted by implementing the existing Autonomous Power EXpert System (APEX), a Lisp-based power expert system, in ART-Ada. Three components, the rule-based expert systems, a graphics user interface, and communications software make up SMART-Ada (Systems fault Management with ART-Ada). The rules were written in the ART-Ada development environment and converted to Ada source code. The graphics interface was developed with the Transportable Application Environment (TAE) Plus, which generates Ada source code to control graphics images. SMART-Ada communicates with a remote host to obtain either simulated or real data. The Ada source code generated with ART-Ada, TAE Plus, and communications code was incorporated into an Ada expert system that reads the data from a power distribution test bed, applies the rule to determine a fault, if one exists, and graphically displays it on the screen. The main objective, to conduct a beta test on the ART-Ada rule-based expert system shell, was achieved. The system is operational. New Ada tools will assist in future successful projects. ART-Ada is one such tool and is a viable alternative to the straight Ada code when an application requires a rule-based or knowledge-based approach.

Internet Data Distribution – extending real-time data sharing throughout the Americas

Directory of Open Access Journals (Sweden)

T. Yoksas

2006-01-01

Full Text Available The Unidata Program Center (Unidata of the University Corporation of Atmospheric Research (UCAR is involved in three international collaborations whose goals are extension of real-time data delivery-to and sharing-of locally held datasets-by educational institutions throughout the Americas. These efforts are based on the use of Unidata's Internet Data Distribution (IDD system which is built on top of its proven Local Data Manager Version 6 (LDM-6 technology. The Unidata IDD is an event-driven network of cooperating Unidata LDM servers that distributes discipline-neutral data products in near real-time over wide-area networks. The IDD, a collaboration of over 150 mostly North American institutions of higher education, has been the primary source of real-time atmospheric science data for the US university community for over a decade,. In addition to providing a highly reliable mechanism for delivering real-time data, the IDD allows users to easily share locally held datasets.

Software/hardware distributed processing network supporting the Ada environment

Science.gov (United States)

Wood, Richard J.; Pryk, Zen

1993-09-01

A high-performance, fault-tolerant, distributed network has been developed, tested, and demonstrated. The network is based on the MIPS Computer Systems, Inc. R3000 Risc for processing, VHSIC ASICs for high speed, reliable, inter-node communications and compatible commercial memory and I/O boards. The network is an evolution of the Advanced Onboard Signal Processor (AOSP) architecture. It supports Ada application software with an Ada- implemented operating system. A six-node implementation (capable of expansion up to 256 nodes) of the RISC multiprocessor architecture provides 120 MIPS of scalar throughput, 96 Mbytes of RAM and 24 Mbytes of non-volatile memory. The network provides for all ground processing applications, has merit for space-qualified RISC-based network, and interfaces to advanced Computer Aided Software Engineering (CASE) tools for application software development.

ART/Ada and CLIPS/Ada

Science.gov (United States)

Culbert, Chris

1990-01-01

Although they have reached a point of commercial viability, expert systems were originally developed in artificial intelligence (AI) research environments. Many of the available tools still work best in such environments. These environments typically utilize special hardware such as LISP machines and relatively unfamiliar languages such as LISP or Prolog. Space Station applications will require deep integration of expert system technology with applications developed in conventional languages, specifically Ada. The ability to apply automation to Space Station functions could be greatly enhanced by widespread availability of state-of-the-art expert system tools based on Ada. Although there have been some efforts to examine the use of Ada for AI applications, there are few, if any, existing products which provide state-of-the-art AI capabilities in an Ada tool. The goal of the ART/Ada Design Project is to conduct research into the implementation in Ada of state-of-the-art hybrid expert systems building tools (ESBT's). This project takes the following approach: using the existing design of the ART-IM ESBT as a starting point, analyze the impact of the Ada language and Ada development methodologies on that design; redesign the system in Ada; and analyze its performance. The research project will attempt to achieve a comprehensive understanding of the potential for embedding expert systems in Ada systems for eventual application in future Space Station Freedom projects. During Phase 1 of the project, initial requirements analysis, design, and implementation of the kernel subset of ART-IM functionality was completed. During Phase 2, the effort has been focused on the implementation and performance analysis of several versions with increasing functionality. Since production quality ART/Ada tools will not be available for a considerable time, and additional subtask of this project will be the completion of an Ada version of the CLIPS expert system shell developed by NASA

Real-Time Analysis and Forecasting of Multisite River Flow Using a Distributed Hydrological Model

Directory of Open Access Journals (Sweden)

Mingdong Sun

2014-01-01

Full Text Available A spatial distributed hydrological forecasting system was developed to promote the analysis of river flow dynamic state in a large basin. The research presented the real-time analysis and forecasting of multisite river flow in the Nakdong River Basin using a distributed hydrological model with radar rainfall forecast data. A real-time calibration algorithm of hydrological distributed model was proposed to investigate the particular relationship between the water storage and basin discharge. Demonstrate the approach of simulating multisite river flow using a distributed hydrological model couple with real-time calibration and forecasting of multisite river flow with radar rainfall forecasts data. The hydrographs and results exhibit that calibrated flow simulations are very approximate to the flow observation at all sites and the accuracy of forecasting flow is gradually decreased with lead times extending from 1 hr to 3 hrs. The flow forecasts are lower than the flow observation which is likely caused by the low estimation of radar rainfall forecasts. The research has well demonstrated that the distributed hydrological model is readily applicable for multisite real-time river flow analysis and forecasting in a large basin.

Real-time measurements and their effects on state estimation of distribution power system

DEFF Research Database (Denmark)

Han, Xue; You, Shi; Thordarson, Fannar

2013-01-01

between the estimated values (voltage and injected power) and the measurements are applied to evaluate the accuracy of the estimated grid states. Eventually, some suggestions are provided for the distribution grid operators on placing the real-time meters in the distribution grid.......This paper aims at analyzing the potential value of using different real-time metering and measuring instruments applied in the low voltage distribution networks for state-estimation. An algorithm is presented to evaluate different combinations of metering data using a tailored state estimator....... It is followed by a case study based on the proposed algorithm. A real distribution grid feeder with different types of meters installed either in the cabinets or at the customer side is selected for simulation and analysis. Standard load templates are used to initiate the state estimation. The deviations...

CREASE 6.0 Catalog of Resources for Education in Ada and Software Engineering

Science.gov (United States)

1992-02-01

Programming Software Engineering Strong Typing Tasking Audene . Computer Scientists Terbook(s): Barnes, J. Programming in Ada, 3rd ed. Addison-Wesley...Ada. Concept: Abstract Data Types Management Overview Package Real-Time Programming Tasking Audene Computer Scientists Textbook(s): Barnes, J

Blocking Optimality in Distributed Real-Time Locking Protocols

Directory of Open Access Journals (Sweden)

Björn Bernhard Brandenburg

2014-09-01

Full Text Available Lower and upper bounds on the maximum priority inversion blocking (pi-blocking that is generally unavoidable in distributed multiprocessor real-time locking protocols (where resources may be accessed only from specific synchronization processors are established. Prior work on suspension-based shared-memory multiprocessor locking protocols (which require resources to be accessible from all processors has established asymptotically tight bounds of Ω(m and Ω(n maximum pi-blocking under suspension-oblivious and suspension-aware analysis, respectively, where m denotes the total number of processors and n denotes the number of tasks. In this paper, it is shown that, in the case of distributed semaphore protocols, there exist two different task allocation scenarios that give rise to distinct lower bounds. In the case of co-hosted task allocation, where application tasks may also be assigned to synchronization processors (i.e., processors hosting critical sections, Ω(Φ · n maximum pi-blocking is unavoidable for some tasks under any locking protocol under both suspension-aware and suspension-oblivious schedulability analysis, where Φ denotes the ratio of the maximum response time to the shortest period. In contrast, in the case of disjoint task allocation (i.e., if application tasks may not be assigned to synchronization processors, only Ω(m and Ω(n maximum pi-blocking is fundamentally unavoidable under suspension-oblivious and suspension-aware analysis, respectively, as in the shared-memory case. These bounds are shown to be asymptotically tight with the construction of two new distributed real-time locking protocols that ensure O(m and O(n maximum pi-blocking under suspension-oblivious and suspension-aware analysis, respectively.

The response-time distribution in a real-time database with optimistic concurrency control and constant execution times

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1997-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response-time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction uses an equal number of

The response-time distribution in a real-time database with optimistic concurrency control and exponential execution times

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1997-01-01

For a real-time shared-memory database with optimistic concurrency control, an approximation for the transaction response-time distribution is obtained. The model assumes that transactions arrive at the database according to a Poisson process, that every transaction takes an exponential execution

Providing Survivable Real-Time Communication Service for Distributed Mission Critical Systems

National Research Council Canada - National Science Library

Zhao, Wei; Bettati, Riccardo; Vaidya, Nitin

2005-01-01

This document is the final report for Providing Survivable Real-Time Communication Service for Distributed Mission Critical Systems, a Texas A AND M project funded through the DARPA Fault Tolerant Networks Program...

The FERMI-Elettra distributed real-time framework

International Nuclear Information System (INIS)

Pivetta, L.; Gaio, G.; Passuello, R.; Scalamera, G.

2012-01-01

FERMI-Elettra is a Free Electron Laser (FEL) based on a 1.5 GeV linac. The pulsed operation of the accelerator and the necessity to characterize and control each electron bunch requires synchronous acquisition of the beam diagnostics together with the ability to drive actuators in real-time at the linac repetition rate. The Adeos/Xenomai real-time extensions have been adopted in order to add real-time capabilities to the Linux based control system computers running the Tango software. A software communication protocol based on Gigabit Ethernet and known as Network Reflective Memory (NRM) has been developed to implement a shared memory across the whole control system, allowing computers to communicate in real-time. The NRM architecture, the real-time performance and the integration in the control system are described. (authors)

Distributed digital real-time control system for TCV tokamak

Energy Technology Data Exchange (ETDEWEB)

Le, H.B. [École Polytechnique Fédérale de Lausanne (EPFL), Centre de Recherches en Physique des Plasmas (CRPP), Association EURATOM-Confédération Suisse, CH-1015 Lausanne (Switzerland); Felici, F. [Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands); Paley, J.I.; Duval, B.P.; Moret, J.-M.; Coda, S.; Sauter, O.; Fasel, D.; Marmillod, P. [École Polytechnique Fédérale de Lausanne (EPFL), Centre de Recherches en Physique des Plasmas (CRPP), Association EURATOM-Confédération Suisse, CH-1015 Lausanne (Switzerland)

2014-03-15

Highlights: • A new distributed digital control system for the TCV tokamak has been commissioned. • Data is shared in real-time between all nodes using the reflective memory. • The customised Linux OS allows achieving deterministic and low latency behaviour. • The control algorithm design in Simulink together with the automatic code generation using Embedded Coder allow rapid algorithm development. • Controllers designed outside the TCV environment can be ported easily. • The previous control system functions have been emulated and improved. • New capabilities include MHD control, profile control, equilibrium reconstruction. - Abstract: A new digital feedback control system (named the SCD “Système de Contrôle Distribué”) has been developed, integrated and used successfully to control TCV (Tokamak à Configuration Variable) plasmas. The system is designed to be modular, distributed, and scalable, accommodating hundreds of diagnostic inputs and actuator outputs. With many more inputs and outputs available than previously possible, it offers the possibility to design advanced control algorithms with better knowledge of the plasma state and to coherently control all TCV actuators, including poloidal field (PF) coils, gas valves, the gyrotron powers and launcher angles of the electron cyclotron heating and current drive system (ECRH/ECCD) together with diagnostic triggering signals. The system consists of multiple nodes; each is a customised Linux desktop or embedded PC which may have local ADC and DAC cards. Each node is also connected to a memory network (reflective memory) providing a reliable, deterministic method of sharing memory between all nodes. Control algorithms are programmed as block diagrams in Matlab-Simulink providing a powerful environment for modelling and control design. The C code is generated automatically from the Simulink block diagram and compiled, with the Simulink Embedded Coder (SEC, formerly Real-Time Workshop Embedded

Flexibility Driven Scheduling and Mapping for Distributed Real-Time Systems

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Peng, Zebo

2002-01-01

In this paper we present an approach to mapping and scheduling of distributed hard real-time systems, aiming at improving the flexibility of the design process. We consider an incremental design process that starts from an already existing system running a set of applications, with preemptive...

Distributed computing for real-time petroleum reservoir monitoring

Energy Technology Data Exchange (ETDEWEB)

Ayodele, O. R. [University of Alberta, Edmonton, AB (Canada)

2004-05-01

Computer software architecture is presented to illustrate how the concept of distributed computing can be applied to real-time reservoir monitoring processes, permitting the continuous monitoring of the dynamic behaviour of petroleum reservoirs at much shorter intervals. The paper describes the fundamental technologies driving distributed computing, namely Java 2 Platform Enterprise edition (J2EE) by Sun Microsystems, and the Microsoft Dot-Net (Microsoft.Net) initiative, and explains the challenges involved in distributed computing. These are: (1) availability of permanently placed downhole equipment to acquire and transmit seismic data; (2) availability of high bandwidth to transmit the data; (3) security considerations; (4) adaptation of existing legacy codes to run on networks as downloads on demand; and (5) credibility issues concerning data security over the Internet. Other applications of distributed computing in the petroleum industry are also considered, specifically MWD, LWD and SWD (measurement-while-drilling, logging-while-drilling, and simulation-while-drilling), and drill-string vibration monitoring. 23 refs., 1 fig.

ISSUES IN MOBILE DISTRIBUTED REAL TIME DATABASES: PERFORMANCE AND REVIEW

OpenAIRE

VISHNU SWAROOP,; Gyanendra Kumar Gupta,; UDAI SHANKER

2011-01-01

Increase in handy and small electronic devices in computing fields; it makes the computing more popularand useful in business. Tremendous advances in wireless networks and portable computing devices have led to development of mobile computing. Support of real time database system depending upon thetiming constraints, due to availability of data distributed database, and ubiquitous computing pull the mobile database concept, which emerges them in a new form of technology as mobile distributed ...

Validation of a Robust Neural Real-Time Voltage Estimator for Active Distribution Grids on Field Data

DEFF Research Database (Denmark)

Pertl, Michael; Douglass, Philip James; Heussen, Kai

2018-01-01

network approach for voltage estimation in active distribution grids by means of measured data from two feeders of a real low voltage distribution grid. The approach enables a real-time voltage estimation at locations in the distribution grid, where otherwise only non-real-time measurements are available......The installation of measurements in distribution grids enables the development of data driven methods for the power system. However, these methods have to be validated in order to understand the limitations and capabilities for their use. This paper presents a systematic validation of a neural...

Timing Analysis of Mixed-Criticality Hard Real-Time Applications Implemented on Distributed Partitioned Architectures

DEFF Research Database (Denmark)

Marinescu, Sorin Ovidiu; Tamas-Selicean, Domitian; Acretoaie, Vlad

In this paper we are interested in the timing analysis of mixed-criticality embedded real-time applications mapped on distributed heterogeneous architectures. Mixedcriticality tasks can be integrated onto the same architecture only if there is enough spatial and temporal separation among them. We...... in partitions using fixedpriority preemptive scheduling. We have extended the stateof- the-art algorithms for schedulability analysis to take into account the partitions. The proposed algorithm has been evaluated using several synthetic and real-life benchmarks....... consider that the separation is provided by partitioning, such that applications run in separate partitions, and each partition is allocated several time slots on a processor. Each partition can have its own scheduling policy. We are interested to determine the worst-case response times of tasks scheduled...

First International Conference on Ada (R) Programming Language Applications for the NASA Space Station, volume 1

Science.gov (United States)

Bown, Rodney L. (Editor)

1986-01-01

Topics discussed include: test and verification; environment issues; distributed Ada issues; life cycle issues; Ada in Europe; management/training issues; common Ada interface set; and run time issues.

Real-time analysis of total, elemental, and total speciated mercury

International Nuclear Information System (INIS)

Schlager, R.J.; Wilson, K.G.; Sappey, A.D.

1995-01-01

ADA Technologies, Inc., is developing a continuous emissions monitoring system that measures the concentrations of mercury in flue gas. Mercury is emitted as an air pollutant from a number of industrial processes. The largest contributors of these emissions are coal and oil combustion, municipal waste combustion, medical waste combustion, and the thermal treatment of hazardous materials. It is difficult, time consuming, and expensive to measure mercury emissions using current testing methods. Part of the difficulty lies in the fact that mercury is emitted from sources in several different forms, such as elemental mercury and mercuric chloride. The ADA analyzer measures these emissions in real time, thus providing a number of advantages over existing test methods: (1) it will provide a real-time measure of emission rates, (2) it will assure facility operators, regulators, and the public that emissions control systems are working at peak efficiency, and (3) it will provide information as to the nature of the emitted mercury (elemental mercury or speciated compounds). This update presents an overview of the CEM and describes features of key components of the monitoring system--the mercury detector, a mercury species converter, and the analyzer calibration system

Real-time analysis of total, elemental, and total speciated mercury

Energy Technology Data Exchange (ETDEWEB)

Schlager, R.J.; Wilson, K.G.; Sappey, A.D. [ADA Technologies, Inc., Englewood, CO (United States)

1995-11-01

ADA Technologies, Inc., is developing a continuous emissions monitoring system that measures the concentrations of mercury in flue gas. Mercury is emitted as an air pollutant from a number of industrial processes. The largest contributors of these emissions are coal and oil combustion, municipal waste combustion, medical waste combustion, and the thermal treatment of hazardous materials. It is difficult, time consuming, and expensive to measure mercury emissions using current testing methods. Part of the difficulty lies in the fact that mercury is emitted from sources in several different forms, such as elemental mercury and mercuric chloride. The ADA analyzer measures these emissions in real time, thus providing a number of advantages over existing test methods: (1) it will provide a real-time measure of emission rates, (2) it will assure facility operators, regulators, and the public that emissions control systems are working at peak efficiency, and (3) it will provide information as to the nature of the emitted mercury (elemental mercury or speciated compounds). This update presents an overview of the CEM and describes features of key components of the monitoring system--the mercury detector, a mercury species converter, and the analyzer calibration system.

Update of GRASP/Ada reverse engineering tools for Ada

Science.gov (United States)

Cross, James H., II

1993-01-01

The GRASP/Ada project (Graphical Representations of Algorithms, Structures, and Processes for Ada) successfully created and prototyped a new algorithmic level graphical representation for Ada software, the Control Structure Diagram (CSD). The primary impetus for creation of the CSD was to improve the comprehension efficiency of Ada software and, as a result, improve reliability and reduce costs. The emphasis was on the automatic generation of the CSD from Ada PDL or source code to support reverse engineering and maintenance. The CSD has the potential to replace traditional pretty printed Ada source code. In Phase 1 of the GRASP/Ada project, the CSD graphical constructs were created and applied manually to several small Ada programs. A prototype CSD generator (Version 1) was designed and implemented using FLEX and BISON running under VMS on a VAX 11-780. In Phase 2, the prototype was improved and ported to the Sun 4 platform under UNIX. A user interface was designed and partially implemented using the HP widget toolkit and the X Windows System. In Phase 3, the user interface was extensively reworked using the Athena widget toolkit and X Windows. The prototype was applied successfully to numerous Ada programs ranging in size from several hundred to several thousand lines of source code. Following Phase 3,e two update phases were completed. Update'92 focused on the initial analysis of evaluation data collected from software engineering students at Auburn University and the addition of significant enhancements to the user interface. Update'93 (the current update) focused on the statistical analysis of the data collected in the previous update and preparation of Version 3.4 of the prototype for limited distribution to facilitate further evaluation. The current prototype provides the capability for the user to generate CSD's from Ada PDL or source code in a reverse engineering as well as forward engineering mode with a level of flexibility suitable for practical

Scalable Real-Time Negotiation Toolkit

National Research Council Canada - National Science Library

Lesser, Victor

2004-01-01

... to implement an adaptive distributed sensor network. These activities involved the development of a distributed soft, real-time heuristic resource allocation protocol, the development of a domain-independent soft, real time agent architecture...

Data-driven modeling and real-time distributed control for energy efficient manufacturing systems

International Nuclear Information System (INIS)

Zou, Jing; Chang, Qing; Arinez, Jorge; Xiao, Guoxian

2017-01-01

As manufacturers face the challenges of increasing global competition and energy saving requirements, it is imperative to seek out opportunities to reduce energy waste and overall cost. In this paper, a novel data-driven stochastic manufacturing system modeling method is proposed to identify and predict energy saving opportunities and their impact on production. A real-time distributed feedback production control policy, which integrates the current and predicted system performance, is established to improve the overall profit and energy efficiency. A case study is presented to demonstrate the effectiveness of the proposed control policy. - Highlights: • A data-driven stochastic manufacturing system model is proposed. • Real-time system performance and energy saving opportunity identification method is developed. • Prediction method for future potential system performance and energy saving opportunity is developed. • A real-time distributed feedback control policy is established to improve energy efficiency and overall system profit.

A distributed scheduling algorithm for heterogeneous real-time systems

Science.gov (United States)

Zeineldine, Osman; El-Toweissy, Mohamed; Mukkamala, Ravi

1991-01-01

Much of the previous work on load balancing and scheduling in distributed environments was concerned with homogeneous systems and homogeneous loads. Several of the results indicated that random policies are as effective as other more complex load allocation policies. The effects of heterogeneity on scheduling algorithms for hard real time systems is examined. A distributed scheduler specifically to handle heterogeneities in both nodes and node traffic is proposed. The performance of the algorithm is measured in terms of the percentage of jobs discarded. While a random task allocation is very sensitive to heterogeneities, the algorithm is shown to be robust to such non-uniformities in system components and load.

A Real-Time Fault Management Software System for Distributed Environments, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — DyMA-FM (Dynamic Multivariate Assessment for Fault Management) is a software architecture for real-time fault management. Designed to run in a distributed...

An Optimization Framework for Dynamic, Distributed Real-Time Systems

Science.gov (United States)

Eckert, Klaus; Juedes, David; Welch, Lonnie; Chelberg, David; Bruggerman, Carl; Drews, Frank; Fleeman, David; Parrott, David; Pfarr, Barbara

2003-01-01

Abstract. This paper presents a model that is useful for developing resource allocation algorithms for distributed real-time systems .that operate in dynamic environments. Interesting aspects of the model include dynamic environments, utility and service levels, which provide a means for graceful degradation in resource-constrained situations and support optimization of the allocation of resources. The paper also provides an allocation algorithm that illustrates how to use the model for producing feasible, optimal resource allocations.

Towards Real-Time Distributed Planning in Multi-Robot Systems

KAUST Repository

Abdelkader, Mohamed

2018-04-01

Recently, there has been an increasing interest in robotics related to multi-robot applications. Such systems can be involved in several tasks such as collaborative search and rescue, aerial transportation, surveillance, and monitoring, to name a few. There are two possible architectures for the autonomous control of multi-robot systems. In the centralized architecture, a master controller communicates with all the robots to collect information. It uses this information to make decisions for the entire system and then sends commands to each robot. In contrast, in the distributed architecture, each robot makes its own decision independent from a central authority. While distributed architecture is a more portable solution, it comes at the expense of extensive information exchange (communication). The extensive communication between robots can result in decision delays because of which distributed architecture is often impractical for systems with strict real-time constraints, e.g. when decisions have to be taken in the order of milliseconds. In this thesis, we propose a distributed framework that strikes a balance between limited communicated information and reasonable system-wide performance while running in real-time. We implement the proposed approach in a game setting of two competing teams of drones, defenders and attackers. Defending drones execute a proposed linear program algorithm (using only onboard computing modules) to obstruct attackers from infiltrating a defense zone while having minimal local message passing. Another main contribution is that we developed a realistic simulation environment as well as lab and outdoor hardware setups of customized drones for testing the system in realistic scenarios. Our software is completely open-source and fully integrated with the well-known Robot Operating System (ROS) in hopes to make our work easily reproducible and for rapid future improvements.

Real time testing of intelligent relays for synchronous distributed generation islanding detection

Science.gov (United States)

Zhuang, Davy

As electric power systems continue to grow to meet ever-increasing energy demand, their security, reliability, and sustainability requirements also become more stringent. The deployment of distributed energy resources (DER), including generation and storage, in conventional passive distribution feeders, gives rise to integration problems involving protection and unintentional islanding. Distributed generators need to be islanded for safety reasons when disconnected or isolated from the main feeder as distributed generator islanding may create hazards to utility and third-party personnel, and possibly damage the distribution system infrastructure, including the distributed generators. This thesis compares several key performance indicators of a newly developed intelligent islanding detection relay, against islanding detection devices currently used by the industry. The intelligent relay employs multivariable analysis and data mining methods to arrive at decision trees that contain both the protection handles and the settings. A test methodology is developed to assess the performance of these intelligent relays on a real time simulation environment using a generic model based on a real-life distribution feeder. The methodology demonstrates the applicability and potential advantages of the intelligent relay, by running a large number of tests, reflecting a multitude of system operating conditions. The testing indicates that the intelligent relay often outperforms frequency, voltage and rate of change of frequency relays currently used for islanding detection, while respecting the islanding detection time constraints imposed by standing distributed generator interconnection guidelines.

Real-Time Simulation and Hardware-in-the-Loop Testbed for Distribution Synchrophasor Applications

Directory of Open Access Journals (Sweden)

Matthias Stifter

2018-04-01

Full Text Available With the advent of Distribution Phasor Measurement Units (D-PMUs and Micro-Synchrophasors (Micro-PMUs, the situational awareness in power distribution systems is going to the next level using time-synchronization. However, designing, analyzing, and testing of such accurate measurement devices are still challenging. Due to the lack of available knowledge and sufficient history for synchrophasors’ applications at the power distribution level, the realistic simulation, and validation environments are essential for D-PMU development and deployment. This paper presents a vendor agnostic PMU real-time simulation and hardware-in-the-Loop (PMU-RTS-HIL testbed, which helps in multiple PMUs validation and studies. The network of real and virtual PMUs was built in a full time-synchronized environment for PMU applications’ validation. The proposed testbed also includes an emulated communication network (CNS layer to replicate bandwidth, packet loss and collisions conditions inherent to the PMUs data streams’ issues. Experimental results demonstrate the flexibility and scalability of the developed PMU-RTS-HIL testbed by producing large amounts of measurements under typical normal and abnormal distribution grid operation conditions.

Ada issues in implementing ART-Ada

Science.gov (United States)

Lee, S. Daniel

1990-01-01

Due to the Ada mandate of a number of government agencies, interest in deploying expert systems such as Ada has increased. Recently, several Ada-based expert system tools have been developed. According to a recent benchmark report, these tools do not perform as well as similar tools written in C. While poorly implemented Ada compilers contribute to the poor benchmark result, some fundamental problems of the Ada language itself have been uncovered. Here, the authors describe Ada language issues encountered during the deployment of ART-Ada, an expert system tool for Ada deployment. ART-Ada is being used to implement several prototype expert systems for the Space Station Freedom and the U.S. Air Force.

An Environment for Incremental Development of Distributed Extensible Asynchronous Real-time Systems

Science.gov (United States)

Ames, Charles K.; Burleigh, Scott; Briggs, Hugh C.; Auernheimer, Brent

1996-01-01

Incremental parallel development of distributed real-time systems is difficult. Architectural techniques and software tools developed at the Jet Propulsion Laboratory's (JPL's) Flight System Testbed make feasible the integration of complex systems in various stages of development.

Real-time generation of the Wigner distribution of complex functions using phase conjugation in photorefractive materials.

Science.gov (United States)

Sun, P C; Fainman, Y

1990-09-01

An optical processor for real-time generation of the Wigner distribution of complex amplitude functions is introduced. The phase conjugation of the input signal is accomplished by a highly efficient self-pumped phase conjugator based on a 45 degrees -cut barium titanate photorefractive crystal. Experimental results on the real-time generation of Wigner distribution slices for complex amplitude two-dimensional optical functions are presented and discussed.

Evaluating Distributed Timing Constraints

DEFF Research Database (Denmark)

Kristensen, C.H.; Drejer, N.

1994-01-01

In this paper we describe a solution to the problem of implementing time-optimal evaluation of timing constraints in distributed real-time systems.......In this paper we describe a solution to the problem of implementing time-optimal evaluation of timing constraints in distributed real-time systems....

Large distributed control system using Ada in fusion research

International Nuclear Information System (INIS)

Van Arsdall, P J; Woodruff, J P.

1998-01-01

Construction of the National Ignition Facility laser at Lawrence Livermore National Laboratory features a distributed control system that uses object-oriented software engineering techniques. Control of 60,000 devices is effected using a network of some 500 computers. The software is being written in Ada and communicates through CORBA. Software controls are implemented in two layers: individual device controllers and a supervisory layer. The software architecture provides services in the form of frameworks that address issues common to event-driven control systems. Those services are allocated to levels that strictly prescribe their interdependency so the levels are separately reusable. The project has completed its final design review. The delivery of the first increment takes place in October 1998. Keywords Distributed control system, object-oriented development, CORBA, application frameworks, levels of abstraction

Energy-Aware Synthesis of Fault-Tolerant Schedules for Real-Time Distributed Embedded Systems

DEFF Research Database (Denmark)

Poulsen, Kåre Harbo; Pop, Paul; Izosimov, Viacheslav

2007-01-01

This paper presents a design optimisation tool for distributed embedded real-time systems that 1) decides mapping, fault-tolerance policy and generates a fault-tolerant schedule, 2) is targeted for hard real-time, 3) has hard reliability goal, 4) generates static schedule for processes and messages......, 5) provides fault-tolerance for k transient/soft faults, 6) optimises for minimal energy consumption, while considering impact of lowering voltages on the probability of faults, 7) uses constraint logic programming (CLP) based implementation....

The development of a program analysis environment for Ada: Reverse engineering tools for Ada

Science.gov (United States)

Cross, James H., II

1991-01-01

The Graphical Representations of Algorithms, Structures, and Processes for Ada (GRASP/Ada) has successfully created and prototyped a new algorithm level graphical representation for Ada software, the Control Structure Diagram (CSD). The primary impetus for creation of the CSD was to improve the comprehension efficiency of Ada software and thus improve reliability and reduce costs. The emphasis was on the automatic generation of the CSD from Ada source code to support reverse engineering and maintenance. The CSD has the potential to replace traditional prettyprinted Ada source code. In Phase 1 of the GRASP/Ada project, the CSD graphical constructs were created and applied manually to several small Ada programs. A prototype (Version 1) was designed and implemented using FLEX and BISON running under the Virtual Memory System (VMS) on a VAX 11-780. In Phase 2, the prototype was improved and ported to the Sun 4 platform under UNIX. A user interface was designed and partially implemented. The prototype was applied successfully to numerous Ada programs ranging in size from several hundred to several thousand lines of source code. In Phase 3 of the project, the prototype was prepared for limited distribution (GRASP/Ada Version 3.0) to facilitate evaluation. The user interface was extensively reworked. The current prototype provides the capability for the user to generate CSD from Ada source code in a reverse engineering mode with a level of flexibility suitable for practical application.

Large-scale machine learning and evaluation platform for real-time traffic surveillance

Science.gov (United States)

Eichel, Justin A.; Mishra, Akshaya; Miller, Nicholas; Jankovic, Nicholas; Thomas, Mohan A.; Abbott, Tyler; Swanson, Douglas; Keller, Joel

2016-09-01

In traffic engineering, vehicle detectors are trained on limited datasets, resulting in poor accuracy when deployed in real-world surveillance applications. Annotating large-scale high-quality datasets is challenging. Typically, these datasets have limited diversity; they do not reflect the real-world operating environment. There is a need for a large-scale, cloud-based positive and negative mining process and a large-scale learning and evaluation system for the application of automatic traffic measurements and classification. The proposed positive and negative mining process addresses the quality of crowd sourced ground truth data through machine learning review and human feedback mechanisms. The proposed learning and evaluation system uses a distributed cloud computing framework to handle data-scaling issues associated with large numbers of samples and a high-dimensional feature space. The system is trained using AdaBoost on 1,000,000 Haar-like features extracted from 70,000 annotated video frames. The trained real-time vehicle detector achieves an accuracy of at least 95% for 1/2 and about 78% for 19/20 of the time when tested on ˜7,500,000 video frames. At the end of 2016, the dataset is expected to have over 1 billion annotated video frames.

Real-time dynamic imaging of virus distribution in vivo.

Directory of Open Access Journals (Sweden)

Sean E Hofherr

2011-02-01

Full Text Available The distribution of viruses and gene therapy vectors is difficult to assess in a living organism. For instance, trafficking in murine models can usually only be assessed after sacrificing the animal for tissue sectioning or extraction. These assays are laborious requiring whole animal sectioning to ascertain tissue localization. They also obviate the ability to perform longitudinal or kinetic studies in one animal. To track viruses after systemic infection, we have labeled adenoviruses with a near-infrared (NIR fluorophore and imaged these after intravenous injection in mice. Imaging was able to track and quantitate virus particles entering the jugular vein simultaneous with injection, appearing in the heart within 500 milliseconds, distributing in the bloodstream and throughout the animal within 7 seconds, and that the bulk of virus distribution was essentially complete within 3 minutes. These data provide the first in vivo real-time tracking of the rapid initial events of systemic virus infection.

Real-time distributed economic model predictive control for complete vehicle energy management

NARCIS (Netherlands)

Romijn, Constantijn; Donkers, Tijs; Kessels, John; Weiland, Siep

2017-01-01

In this paper, a real-time distributed economic model predictive control approach for complete vehicle energy management (CVEM) is presented using a receding control horizon in combination with a dual decomposition. The dual decomposition allows the CVEM optimization problem to be solved by solving

SEL Ada reuse analysis and representations

Science.gov (United States)

Kester, Rush

1990-01-01

Overall, it was revealed that the pattern of Ada reuse has evolved from initial reuse of utility components into reuse of generalized application architectures. Utility components were both domain-independent utilities, such as queues and stacks, and domain-specific utilities, such as those that implement spacecraft orbit and attitude mathematical functions and physics or astronomical models. The level of reuse was significantly increased with the development of a generalized telemetry simulator architecture. The use of Ada generics significantly increased the level of verbatum reuse, which is due to the ability, using Ada generics, to parameterize the aspects of design that are configurable during reuse. A key factor in implementing generalized architectures was the ability to use generic subprogram parameters to tailor parts of the algorithm embedded within the architecture. The use of object oriented design (in which objects model real world entities) significantly improved the modularity for reuse. Encapsulating into packages the data and operations associated with common real world entities creates natural building blocks for reuse.

Strategy-making for a proactive distribution company in the real-time market with demand response

DEFF Research Database (Denmark)

Zhang, Chunyu; Wang, Qi; Wang, Jianhui

2016-01-01

This paper proposes a methodology to optimize the trading strategies of a proactive distribution company (PDISCO) in the real-time market by mobilizing the demand response. Each distribution-level demand is considered as an elastic one. To capture the interrelation between the PDISCO and the real......-time market, a bi-level model is presented for the PDISCO to render continuous offers and bids strategically. The upper level problem expresses the PDISCO's profit maximization, while the lower-level problem minimizes the operation cost of the transmission-level real-time market. To solve the proposed model......, a primal-dual approach is used to translate this bi-level model into a single-level mathematical program with equilibrium constraints. Results of case studies are reported to show the effectiveness of the proposed model. (C) 2016 Elsevier Ltd. All rights reserved....

Ada training evaluation and recommendations from the Gamma Ray Observatory Ada Development Team

International Nuclear Information System (INIS)

1985-10-01

The Ada training experiences of the Gamma Ray Observatory Ada development team are related, and recommendations are made concerning future Ada training for software developers. Training methods are evaluated, deficiencies in the training program are noted, and a recommended approach, including course outline, time allocation, and reference materials, is offered

Real-time Data Access Monitoring in Distributed, Multi-petabyte Systems

Energy Technology Data Exchange (ETDEWEB)

Azemoon, Tofigh; Becla, Jacek, a=Hanushevsky, Andrew; Turri, Massimiliano; /SLAC

2008-04-22

Petascale systems are in existence today and will become common in the next few years. Such systems are inevitably very complex, highly distributed and heterogeneous. Monitoring a petascale system in real-time and understanding its status at any given moment without impacting its performance is a highly intricate task. Common approaches and off-the-shelf tools are either unusable, do not scale, or severely impact the performance of the monitored servers. This paper describes unobtrusive monitoring software developed at Stanford Linear Accelerator Center (SLAC) for a highly distributed petascale production data set. The paper describes the employed solutions, the lessons learned, the problems still to be addressed, and explains how the system can be reused elsewhere.

A Distributed Framework for Real Time Path Planning in Practical Multi-agent Systems

KAUST Repository

Abdelkader, Mohamed; Jaleel, Hassan; Shamma, Jeff S.

2017-01-01

We present a framework for distributed, energy efficient, and real time implementable algorithms for path planning in multi-agent systems. The proposed framework is presented in the context of a motivating example of capture the flag which

NSTX-U Advances in Real-Time C++11 on Linux

Science.gov (United States)

Erickson, Keith G.

2015-08-01

Programming languages like C and Ada combined with proprietary embedded operating systems have dominated the real-time application space for decades. The new C++11 standard includes native, language-level support for concurrency, a required feature for any nontrivial event-oriented real-time software. Threads, Locks, and Atomics now exist to provide the necessary tools to build the structures that make up the foundation of a complex real-time system. The National Spherical Torus Experiment Upgrade (NSTX-U) at the Princeton Plasma Physics Laboratory (PPPL) is breaking new ground with the language as applied to the needs of fusion devices. A new Digital Coil Protection System (DCPS) will serve as the main protection mechanism for the magnetic coils, and it is written entirely in C++11 running on Concurrent Computer Corporation's real-time operating system, RedHawk Linux. It runs over 600 algorithms in a 5 kHz control loop that determine whether or not to shut down operations before physical damage occurs. To accomplish this, NSTX-U engineers developed software tools that do not currently exist elsewhere, including real-time atomic synchronization, real-time containers, and a real-time logging framework. Together with a recent (and carefully configured) version of the GCC compiler, these tools enable data acquisition, processing, and output using a conventional operating system to meet a hard real-time deadline (that is, missing one periodic is a failure) of 200 microseconds.

NSTX-U Advances in Real-Time C++11 on Linux

International Nuclear Information System (INIS)

Erickson, Keith G.

2015-01-01

Programming languages like C and Ada combined with proprietary embedded operating systems have dominated the real-time application space for decades. The new C++11standard includes native, language-level support for concurrency, a required feature for any nontrivial event-oriented real-time software. Threads, Locks, and Atomics now exist to provide the necessary tools to build the structures that make up the foundation of a complex real-time system. The National Spherical Torus Experiment Upgrade (NSTX-U) at the Princeton Plasma Physics Laboratory (PPPL) is breaking new ground with the language as applied to the needs of fusion devices. A new Digital Coil Protection System (DCPS) will serve as the main protection mechanism for the magnetic coils, and it is written entirely in C++11 running on Concurrent Computer Corporation's real-time operating system, RedHawk Linux. It runs over 600 algorithms in a 5 kHz control loop that determine whether or not to shut down operations before physical damage occurs. To accomplish this, NSTX-U engineers developed software tools that do not currently exist elsewhere, including real-time atomic synchronization, real-time containers, and a real-time logging framework. Together with a recent (and carefully configured) version of the GCC compiler, these tools enable data acquisition, processing, and output using a conventional operating system to meet a hard real-time deadline (that is, missing one periodic is a failure) of 200 microseconds

An In-Home Digital Network Architecture for Real-Time and Non-Real-Time Communication

NARCIS (Netherlands)

Scholten, Johan; Jansen, P.G.; Hanssen, F.T.Y.; Hattink, Tjalling

2002-01-01

This paper describes an in-home digital network architecture that supports both real-time and non-real-time communication. The architecture deploys a distributed token mechanism to schedule communication streams and to offer guaranteed quality-ofservice. Essentially, the token mechanism prevents

Data distribution architecture based on standard real time protocol

International Nuclear Information System (INIS)

Castro, R.; Vega, J.; Pereira, A.; Portas, A.

2009-01-01

Data distribution architecture (DDAR) has been designed conforming to new requirements, taking into account the type of data that is going to be generated from experiments in International Thermonuclear Experimental Reactor (ITER). The main goal of this architecture is to implement a system that is able to manage on line all data that is being generated by an experiment, supporting its distribution for: processing, storing, analysing or visualizing. The first objective is to have a distribution architecture that supports long pulse experiments (even hours). The described system is able to distribute, using real time protocol (RTP), stored data or live data generated while the experiment is running. It enables researchers to access data on line instead of waiting for the end of the experiment. Other important objective is scalability, so the presented architecture can easily grow based on actual necessities, simplifying estimation and design tasks. A third important objective is security. In this sense, the architecture is based on standards, so complete security mechanisms can be applied, from secure transmission solutions until elaborated access control policies, and it is full compatible with multi-organization federation systems as PAPI or Shibboleth.

Data distribution architecture based on standard real time protocol

Energy Technology Data Exchange (ETDEWEB)

Castro, R. [Asociacion EURATOM/CIEMAT para Fusion, Avda. Complutense No. 22, 28040 Madrid (Spain)], E-mail: rodrigo.castro@ciemat.es; Vega, J.; Pereira, A.; Portas, A. [Asociacion EURATOM/CIEMAT para Fusion, Avda. Complutense No. 22, 28040 Madrid (Spain)

2009-06-15

Data distribution architecture (DDAR) has been designed conforming to new requirements, taking into account the type of data that is going to be generated from experiments in International Thermonuclear Experimental Reactor (ITER). The main goal of this architecture is to implement a system that is able to manage on line all data that is being generated by an experiment, supporting its distribution for: processing, storing, analysing or visualizing. The first objective is to have a distribution architecture that supports long pulse experiments (even hours). The described system is able to distribute, using real time protocol (RTP), stored data or live data generated while the experiment is running. It enables researchers to access data on line instead of waiting for the end of the experiment. Other important objective is scalability, so the presented architecture can easily grow based on actual necessities, simplifying estimation and design tasks. A third important objective is security. In this sense, the architecture is based on standards, so complete security mechanisms can be applied, from secure transmission solutions until elaborated access control policies, and it is full compatible with multi-organization federation systems as PAPI or Shibboleth.

Design optimization for security-and safety-critical distributed real-time applications

DEFF Research Database (Denmark)

Jiang, Wei; Pop, Paul; Jiang, Ke

2016-01-01

requirements on confidentiality of messages, task replication is used to enhance system reliability, and dynamic voltage and frequency scaling is used for energy efficiency of tasks. It is challenging to address these factors simultaneously, e.g., better security protections need more computing resources......In this paper, we are interested in the design of real-time applications with security, safety, timing, and energy requirements. The applications are scheduled with cyclic scheduling, and are mapped on distributed heterogeneous architectures. Cryptographic services are deployed to satisfy security...... and consume more energy, while lower voltages and frequencies may impair schedulability and security, and also lead to reliability degradation. We introduce a vulnerability based method to quantify the security performance of communications on distributed systems. We then focus on determining the appropriate...

Analysis of fault tolerance and reliability in distributed real-time system architectures

International Nuclear Information System (INIS)

Philippi, Stephan

2003-01-01

Safety critical real-time systems are becoming ubiquitous in many areas of our everyday life. Failures of such systems potentially have catastrophic consequences on different scales, in the worst case even the loss of human life. Therefore, safety critical systems have to meet maximum fault tolerance and reliability requirements. As the design of such systems is far from being trivial, this article focuses on concepts to specifically support the early architectural design. In detail, a simulation based approach for the analysis of fault tolerance and reliability in distributed real-time system architectures is presented. With this approach, safety related features can be evaluated in the early development stages and thus prevent costly redesigns in later ones

Cybersecurity through Real-Time Distributed Control Systems

Energy Technology Data Exchange (ETDEWEB)

Kisner, Roger A [ORNL; Manges, Wayne W [ORNL; MacIntyre, Lawrence Paul [ORNL; Nutaro, James J [ORNL; Munro Jr, John K [ORNL; Ewing, Paul D [ORNL; Howlader, Mostofa [ORNL; Kuruganti, Phani Teja [ORNL; Wallace, Richard M [ORNL; Olama, Mohammed M [ORNL

2010-04-01

Critical infrastructure sites and facilities are becoming increasingly dependent on interconnected physical and cyber-based real-time distributed control systems (RTDCSs). A mounting cybersecurity threat results from the nature of these ubiquitous and sometimes unrestrained communications interconnections. Much work is under way in numerous organizations to characterize the cyber threat, determine means to minimize risk, and develop mitigation strategies to address potential consequences. While it seems natural that a simple application of cyber-protection methods derived from corporate business information technology (IT) domain would lead to an acceptable solution, the reality is that the characteristics of RTDCSs make many of those methods inadequate and unsatisfactory or even harmful. A solution lies in developing a defense-in-depth approach that ranges from protection at communications interconnect levels ultimately to the control system s functional characteristics that are designed to maintain control in the face of malicious intrusion. This paper summarizes the nature of RTDCSs from a cybersecurity perspec tive and discusses issues, vulnerabilities, candidate mitigation approaches, and metrics.

Real-time distributed scheduling algorithm for supporting QoS over WDM networks

Science.gov (United States)

Kam, Anthony C.; Siu, Kai-Yeung

1998-10-01

Most existing or proposed WDM networks employ circuit switching, typically with one session having exclusive use of one entire wavelength. Consequently they are not suitable for data applications involving bursty traffic patterns. The MIT AON Consortium has developed an all-optical LAN/MAN testbed which provides time-slotted WDM service and employs fast-tunable transceivers in each optical terminal. In this paper, we explore extensions of this service to achieve fine-grained statistical multiplexing with different virtual circuits time-sharing the wavelengths in a fair manner. In particular, we develop a real-time distributed protocol for best-effort traffic over this time-slotted WDM service with near-optical fairness and throughput characteristics. As an additional design feature, our protocol supports the allocation of guaranteed bandwidths to selected connections. This feature acts as a first step towards supporting integrated services and quality-of-service guarantees over WDM networks. To achieve high throughput, our approach is based on scheduling transmissions, as opposed to collision- based schemes. Our distributed protocol involves one MAN scheduler and several LAN schedulers (one per LAN) in a master-slave arrangement. Because of propagation delays and limits on control channel capacities, all schedulers are designed to work with partial, delayed traffic information. Our distributed protocol is of the `greedy' type to ensure fast execution in real-time in response to dynamic traffic changes. It employs a hybrid form of rate and credit control for resource allocation. We have performed extensive simulations, which show that our protocol allocates resources (transmitters, receivers, wavelengths) fairly with high throughput, and supports bandwidth guarantees.

A Distributed Framework for Real Time Path Planning in Practical Multi-agent Systems

KAUST Repository

Abdelkader, Mohamed

2017-10-19

We present a framework for distributed, energy efficient, and real time implementable algorithms for path planning in multi-agent systems. The proposed framework is presented in the context of a motivating example of capture the flag which is an adversarial game played between two teams of autonomous agents called defenders and attackers. We start with the centralized formulation of the problem as a linear program because of its computational efficiency. Then we present an approximation framework in which each agent solves a local version of the centralized linear program by communicating with its neighbors only. The premise in this work is that for practical multi-agent systems, real time implementability of distributed algorithms is more crucial then global optimality. Thus, instead of verifying the proposed framework by performing offline simulations in MATLAB, we run extensive simulations in a robotic simulator V-REP, which includes a detailed dynamic model of quadrotors. Moreover, to create a realistic scenario, we allow a human operator to control the attacker quadrotor through a joystick in a single attacker setup. These simulations authenticate that the proposed framework is real time implementable and results in a performance that is comparable with the global optimal solution under the considered scenarios.

Design of Mixed-Criticality Applications on Distributed Real-Time Systems

DEFF Research Database (Denmark)

Tamas-Selicean, Domitian

the concept of virtual links, and temporal separation, enforced through schedule tables for TT messages and bandwidth allocation for RC messages. The objective of this thesis is to develop methods and tools for distributed mixed-criticality real-time systems. At the processor level, we are interested......A mixed-criticality system implements applications of different safety-criticality levels onto the same platform. In such cases, the certification standards require that applications of different criticality levels are protected so they cannot influence each other. Otherwise, all tasks have...

On 'Money' in ISLM and AD/AS Models

OpenAIRE

Thomas K. Rymes; Colin Rogers

2000-01-01

Hicks's ISLM model interpretation of Keynes's theory is subject to much controversy. In this paper, we focus upon the 'real balance' effect and its role in ISLM and AD/AS analyses. We shall argue that ISLM and AD/AS require 'nominal anchors'. We live in a world where, increasingly, the 'money' in the ISLM and AD/AS model no longer exists (as Keynes imperfectly understood in his TREATISE ON MONEy). There are no longer any nominal anchors, rather they have been replaced by discretionary policy....

ADA1, a novel component of the ADA/GCN5 complex, has broader effects than GCN5, ADA2, or ADA3.

OpenAIRE

Horiuchi, J; Silverman, N; Piña, B; Marcus, G A; Guarente, L

1997-01-01

The ADA genes encode factors which are proposed to function as transcriptional coactivators. Here we describe the cloning, sequencing, and initial characterization of a novel ADA gene, ADA1. Similar to the previously isolated ada mutants, ada1 mutants display decreases in transcription from various reporters. Furthermore, ADA1 interacts with the other ADAs in the ADA/GCN5 complex as demonstrated by partial purification of the complex and immunoprecipitation experiments. We estimate that the c...

The R-Shell approach - Using scheduling agents in complex distributed real-time systems

Science.gov (United States)

Natarajan, Swaminathan; Zhao, Wei; Goforth, Andre

1993-01-01

Large, complex real-time systems such as space and avionics systems are extremely demanding in their scheduling requirements. The current OS design approaches are quite limited in the capabilities they provide for task scheduling. Typically, they simply implement a particular uniprocessor scheduling strategy and do not provide any special support for network scheduling, overload handling, fault tolerance, distributed processing, etc. Our design of the R-Shell real-time environment fcilitates the implementation of a variety of sophisticated but efficient scheduling strategies, including incorporation of all these capabilities. This is accomplished by the use of scheduling agents which reside in the application run-time environment and are responsible for coordinating the scheduling of the application.

Hard Real-Time Networking on Firewire

NARCIS (Netherlands)

Zhang, Yuchen; Orlic, Bojan; Visser, Peter; Broenink, Jan

2005-01-01

This paper investigates the possibility of using standard, low-cost, widely used FireWire as a new generation fieldbus medium for real-time distributed control applications. A real-time software subsys- tem, RT-FireWire was designed that can, in combination with Linux-based real-time operating

Implementation of a Real-Time Microgrid Simulation Platform Based on Centralized and Distributed Management

Directory of Open Access Journals (Sweden)

Omid Abrishambaf

2017-06-01

Full Text Available Demand response and distributed generation are key components of power systems. Several challenges are raised at both technical and business model levels for integration of those resources in smart grids and microgrids. The implementation of a distribution network as a test bed can be difficult and not cost-effective; using computational modeling is not sufficient for producing realistic results. Real-time simulation allows us to validate the business model’s impact at the technical level. This paper comprises a platform supporting the real-time simulation of a microgrid connected to a larger distribution network. The implemented platform allows us to use both centralized and distributed energy resource management. Using an optimization model for the energy resource operation, a virtual power player manages all the available resources. Then, the simulation platform allows us to technically validate the actual implementation of the requested demand reduction in the scope of demand response programs. The case study has 33 buses, 220 consumers, and 68 distributed generators. It demonstrates the impact of demand response events, also performing resource management in the presence of an energy shortage.

Design Of Real-Time Implementable Distributed Suboptimal Control: An LQR Perspective

KAUST Repository

Jaleel, Hassan

2017-09-29

We propose a framework for multiagent systems in which the agents compute their control actions in real time, based on local information only. The novelty of the proposed framework is that the process of computing a suboptimal control action is divided into two phases: an offline phase and an online phase. In the offline phase, an approximate problem is formulated with a cost function that is close to the optimal cost in some sense and is distributed, i.e., the costs of non-neighboring nodes are not coupled. This phase is centralized and is completed before the deployment of the system. In the online phase, the approximate problem is solved in real time by implementing any efficient distributed optimization algorithm. To quantify the performance loss, we derive upper bounds for the maximum error between the optimal performance and the performance under the proposed framework. Finally, the proposed framework is applied to an example setup in which a team of mobile nodes is assigned the task of establishing a communication link between two base stations with minimum energy consumption. We show through simulations that the performance under the proposed framework is close to the optimal performance and the suboptimal policy can be efficiently implemented online.

ART-Ada: An Ada-based expert system tool

Science.gov (United States)

Lee, S. Daniel; Allen, Bradley P.

1991-01-01

The Department of Defense mandate to standardize on Ada as the language for software systems development has resulted in increased interest in making expert systems technology readily available in Ada environments. NASA's Space Station Freedom is an example of the large Ada software development projects that will require expert systems in the 1990's. Another large scale application that can benefit from Ada based expert system tool technology is the Pilot's Associate (PA) expert system project for military combat aircraft. Automated Reasoning Tool (ART) Ada, an Ada Expert system tool is described. ART-Ada allow applications of a C-based expert system tool called ART-IM to be deployed in various Ada environments. ART-Ada is being used to implement several prototype expert systems for NASA's Space Station Freedom Program and the U.S. Air Force.

Scheduling and Mapping in an Incremental Design Methodology for Distributed Real-Time Embedded Systems

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Peng, Zebo

2004-01-01

In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at a minimization of the system modification cost. We consider an incremental design process that starts from an already existing system running a set of applicat......In this paper we present an approach to mapping and scheduling of distributed embedded systems for hard real-time applications, aiming at a minimization of the system modification cost. We consider an incremental design process that starts from an already existing system running a set...... be added to the resulted system. Thus, we propose a heuristic which finds the set of already running applications which have to be remapped and rescheduled at the same time with mapping and scheduling the new application, such that the disturbance on the running system (expressed as the total cost implied...... by the modifications) is minimized. Once this set of applications has been determined, we outline a mapping and scheduling algorithm aimed at fulfilling the requirements stated above. The approaches have been evaluated based on extensive experiments using a large number of generated benchmarks as well as a real...

Evaluating pleural ADA, ADA2, IFN-γ and IGRA for diagnosing tuberculous pleurisy.

Science.gov (United States)

Keng, Li-Ta; Shu, Chin-Chung; Chen, Jason Yao-Ping; Liang, Sheng-Kai; Lin, Ching-Kai; Chang, Lih-Yu; Chang, Chia-Hao; Wang, Jann-Yuan; Yu, Chong-Jen; Lee, Li-Na

2013-10-01

Conventional methods for diagnosing tuberculous pleurisy (TB pleurisy) are either invasive or have a long turn-around-time. Performances of pleural adenosine deaminase (ADA), ADA2, interferon-gamma (IFN-γ), and interferon-gamma release assays (IGRA) as diagnostic tools for TB pleurisy were evaluated. Eighty-eight patients with lymphocyte-predominant pleural exudates between June 2010 and March 2011, including 31 with clinically diagnosed TB pleurisy, were prospectively studied. Pleural ADA and ADA2 activity were measured by colorimetric method, IFN-γ levels by enzyme-linked immuno-sorbent assay, and IGRA by enzyme-linked immuno-spot (T-SPOT.TB) assay. Pleural ADA, ADA2, and IFN-γ levels, but not the proportion of positive T-SPOT.TB assay, were significantly higher in patients with TB pleurisy than in those without TB pleurisy. The area under the receiver-operating-characteristic (ROC) curve was 0.920, 0.893, 0.875, and 0.544 for IFN-γ, ADA2, ADA, and T-SPOT.TB assay, respectively. The combination of ADA ≥ 40 IU/L and IFN-γ ≥ 75 pg/mL yielded a specificity of 100%. Pleural ADA, ADA2 and IFN-γ, but not T-SPOT.TB assay, are all sensitive and specific for TB pleurisy. In patients with lymphocyte-predominant pleural exudates, ADA ≥ 40 IU/L and IFN-γ ≥ 75 pg/mL in pleural effusion imply a very high probability of TB pleurisy. Copyright © 2013 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

Electric space heating scheduling for real-time explicit power control in active distribution networks

DEFF Research Database (Denmark)

Costanzo, Giuseppe Tommaso; Bernstein, Andrey; Chamorro, Lorenzo Reyes

2015-01-01

This paper presents a systematic approach for abstracting the flexibility of a building space heating system and using it within a composable framework for real-time explicit power control of microgrids and, more in general, active distribution networks. In particular, the proposed approach...... is developed within the context of a previously defined microgrid control framework, called COMMELEC, conceived for the explicit and real-time control of these specific networks. The designed control algorithm is totally independent from the need of a building model and allows exploiting the intrinsic thermal...... inertia for real-time control. The paper first discusses the general approach, then it proves its validity via dedicated simulations performed on specific case study composed by the CIGRE LV microgrid benchmark proposed by the Cigré TF C6.04.02....

COMDES-II: A Component-Based Framework for Generative Development of Distributed Real-Time Control Systems

DEFF Research Database (Denmark)

Ke, Xu; Sierszecki, Krzysztof; Angelov, Christo K.

2007-01-01

The paper presents a generative development methodology and component models of COMDES-II, a component-based software framework for distributed embedded control systems with real-time constraints. The adopted methodology allows for rapid modeling and validation of control software at a higher lev...... methodology for COMDES-II from a general perspective, describes the component models in details and demonstrates their application through a DC-Motor control system case study.......The paper presents a generative development methodology and component models of COMDES-II, a component-based software framework for distributed embedded control systems with real-time constraints. The adopted methodology allows for rapid modeling and validation of control software at a higher level...

ADA, the Programming Language of Choice for the UPMSat-2 Satellite

Science.gov (United States)

Garrido, Jorge; Zamorano, Juan; de la Puente, Juan A.; Alonso, Alejandro; Salazar, Emilio

2015-09-01

The proper selection of development mechanisms and tools is essential for the final success of any engineering project. This is also true when it comes to software development. Furthermore, when the system shows very specific and hard to meet requirements, as it happens for high-integrity real-time systems, the appropriate selection is crucial. For this kind of systems, Ada has proven to be a successful companion, and satellites are not an exception. The paper presents the reasons behind the selection of Ada for the UPMSat-2 development, along with the experience and examples on its usage.

System-level power optimization for real-time distributed embedded systems

Science.gov (United States)

Luo, Jiong

Power optimization is one of the crucial design considerations for modern electronic systems. In this thesis, we present several system-level power optimization techniques for real-time distributed embedded systems, based on dynamic voltage scaling, dynamic power management, and management of peak power and variance of the power profile. Dynamic voltage scaling has been widely acknowledged as an important and powerful technique to trade off dynamic power consumption and delay. Efficient dynamic voltage scaling requires effective variable-voltage scheduling mechanisms that can adjust voltages and clock frequencies adaptively based on workloads and timing constraints. For this purpose, we propose static variable-voltage scheduling algorithms utilizing criticalpath driven timing analysis for the case when tasks are assumed to have uniform switching activities, as well as energy-gradient driven slack allocation for a more general scenario. The proposed techniques can achieve closeto-optimal power savings with very low computational complexity, without violating any real-time constraints. We also present algorithms for power-efficient joint scheduling of multi-rate periodic task graphs along with soft aperiodic tasks. The power issue is addressed through both dynamic voltage scaling and power management. Periodic task graphs are scheduled statically. Flexibility is introduced into the static schedule to allow the on-line scheduler to make local changes to PE schedules through resource reclaiming and slack stealing, without interfering with the validity of the global schedule. We provide a unified framework in which the response times of aperiodic tasks and power consumption are dynamically optimized simultaneously. Interconnection network fabrics point to a new generation of power-efficient and scalable interconnection architectures for distributed embedded systems. As the system bandwidth continues to increase, interconnection networks become power/energy limited as

Real-time flight test data distribution and display

Science.gov (United States)

Nesel, Michael C.; Hammons, Kevin R.

1988-01-01

Enhancements to the real-time processing and display systems of the NASA Western Aeronautical Test Range are described. Display processing has been moved out of the telemetry and radar acquisition processing systems super-minicomputers into user/client interactive graphic workstations. Real-time data is provided to the workstations by way of Ethernet. Future enhancement plans include use of fiber optic cable to replace the Ethernet.

Software engineering capability for Ada (GRASP/Ada Tool)

Science.gov (United States)

Cross, James H., II

1995-01-01

The GRASP/Ada project (Graphical Representations of Algorithms, Structures, and Processes for Ada) has successfully created and prototyped a new algorithmic level graphical representation for Ada software, the Control Structure Diagram (CSD). The primary impetus for creation of the CSD was to improve the comprehension efficiency of Ada software and, as a result, improve reliability and reduce costs. The emphasis has been on the automatic generation of the CSD from Ada PDL or source code to support reverse engineering and maintenance. The CSD has the potential to replace traditional prettyprinted Ada Source code. A new Motif compliant graphical user interface has been developed for the GRASP/Ada prototype.

SCI-Clone/32 - a distributed real time simulation system

International Nuclear Information System (INIS)

Wilks, C.F.

1986-01-01

Advances in engineering and in particular digital computers has enabled the simulation manufacturers to deliver a realism of a kind undreamt of a decade ago. 32-bit computers ranging in processor power from several hundred thousand instructions per second to many millions are at the heart of each simulator. Gould has pioneered digital computers in simulation with real time systems using shared memory, parallel processors, 64KByte cache, and shadow memory. The market is planning for higher iteration rates, lower life cycle costs, and the development of part task products. These can be met by distributing the tasks amongst nodal computers having a unique architecture for sharing data variables with minimal contention. (Auth.)

Robustness of parameter-less remote real-time pressure control in water distribution systems

CSIR Research Space (South Africa)

Page, Philip R

2017-06-01

Full Text Available One way of reducing water leakage, pipe bursts and water consumption in a water distribution system (WDS) is to manage the pressure to be as low as possible. This can be done by adjusting a pressure control valve (PCV) in real-time in order to keep...

Real-time interactive treatment planning

International Nuclear Information System (INIS)

Otto, Karl

2014-01-01

The goal of this work is to develop an interactive treatment planning platform that permits real-time manipulation of dose distributions including DVHs and other dose metrics. The hypothesis underlying the approach proposed here is that the process of evaluating potential dose distribution options and deciding on the best clinical trade-offs may be separated from the derivation of the actual delivery parameters used for the patient’s treatment. For this purpose a novel algorithm for deriving an Achievable Dose Estimate (ADE) was developed. The ADE algorithm is computationally efficient so as to update dose distributions in effectively real-time while accurately incorporating the limits of what can be achieved in practice. The resulting system is a software environment for interactive real-time manipulation of dose that permits the clinician to rapidly develop a fully customized 3D dose distribution. Graphical navigation of dose distributions is achieved by a sophisticated method of identifying contributing fluence elements, modifying those elements and re-computing the entire dose distribution. 3D dose distributions are calculated in ∼2–20 ms. Including graphics processing overhead, clinicians may visually interact with the dose distribution (e.g. ‘drag’ a DVH) and display updates of the dose distribution at a rate of more than 20 times per second. Preliminary testing on various sites shows that interactive planning may be completed in ∼1–5 min, depending on the complexity of the case (number of targets and OARs). Final DVHs are derived through a separate plan optimization step using a conventional VMAT planning system and were shown to be achievable within 2% and 4% in high and low dose regions respectively. With real-time interactive planning trade-offs between Target(s) and OARs may be evaluated efficiently providing a better understanding of the dosimetric options available to each patient in static or adaptive RT. (paper)

Monuments on Gemiler Ada and Karacaören Ada

OpenAIRE

Masuda, Tomoyuki

1995-01-01

Contents : 1. Church I on Gemiler Ada, 2. Church II on Gemiler Ada, 3. Church III on Gemiler Ada, 4. Church IV on Gemiler Ada, 5. Basilica on Karacaören Ada, 6. Painted Tomb on Karacaören Ada, 7. The Baptistery and the Chronology of Construction of the Karacaören Ada Basilica Complex, 8. Ölüdeniz Beach Basilica, 9. Iskender Basilica on Ölüdeniz Lagoon, 10. Mustafa Basilica near Beştaş Cove.

Estimating medication stopping fraction and real-time prevalence of drug use in pharmaco-epidemiologic databases. An application of the reverse waiting time distribution

DEFF Research Database (Denmark)

Støvring, Henrik; Pottegård, Anton; Hallas, Jesper

2017-01-01

Purpose: To introduce the reverse waiting time distribution (WTD) and show how it can be used to estimate stopping fractions and real-time prevalence of treatment in pharmacoepidemiological studies. Methods: The reverse WTD is the distribution of time from the last dispensed prescription of each......-hoc decision rules for automated implementations, and it yields estimates of real-time prevalence....... patient within a time window to the end of it. It is a mirrored version of the ordinary WTD, which considers the first dispensed prescription of patients within a time window. Based on renewal process theory, the reverse WTD can be analyzed as an ordinary WTD with maximum likelihood estimation. Based...

Real-time definition of non-randomness in the distribution of genomic events.

Directory of Open Access Journals (Sweden)

Ulrich Abel

Full Text Available Features such as mutations or structural characteristics can be non-randomly or non-uniformly distributed within a genome. So far, computer simulations were required for statistical inferences on the distribution of sequence motifs. Here, we show that these analyses are possible using an analytical, mathematical approach. For the assessment of non-randomness, our calculations only require information including genome size, number of (sampled sequence motifs and distance parameters. We have developed computer programs evaluating our analytical formulas for the real-time determination of expected values and p-values. This approach permits a flexible cluster definition that can be applied to most effectively identify non-random or non-uniform sequence motif distribution. As an example, we show the effectivity and reliability of our mathematical approach in clinical retroviral vector integration site distribution.

Timing system solution for MedAustron; Real-time event and data distribution network

International Nuclear Information System (INIS)

Stefanic, R.; Tavcar, R.; Dedic, J.; Gutleber, J.; Moser, R.

2012-01-01

MedAustron is an ion beam research and therapy centre under construction in Wiener Neustadt, Austria. The facility features a synchrotron particle accelerator for light ions. The timing system for this class of accelerators has been developed in close collaboration between MedAustron and Cosylab. Mitigating economical and technological risks, we have chosen a proven, widely used Micro Research Finland (MRF) timing equipment and redesigned its FPGA firmware, extending its high-logic services above transport layer, as required by machine specifics. We obtained a generic real-time broadcast network for coordinating actions of a compact, pulse-to-pulse modulation based particle accelerator. High-level services include support for virtual accelerators and a rich selection of event response mechanisms. The system uses a combination of a real-time link for downstream events and a non-real-time link for upstream messaging and non time-critical communication. It comes with National Instruments LabVIEW-based software support, ready to be integrated into PXIe based front-end controllers. This article explains the high level logic services provided by the real-time link, describes the non-real-time interfaces and presents the software configuration mechanisms. (authors)

Conversion and Validation of Distribution System Model from a QSTS-Based Tool to a Real-Time Dynamic Phasor Simulator

Energy Technology Data Exchange (ETDEWEB)

Chamana, Manohar; Prabakar, Kumaraguru; Palmintier, Bryan; Baggu, Murali M.

2017-05-11

A software process is developed to convert distribution network models from a quasi-static time-series tool (OpenDSS) to a real-time dynamic phasor simulator (ePHASORSIM). The description of this process in this paper would be helpful for researchers who intend to perform similar conversions. The converter could be utilized directly by users of real-time simulators who intend to perform software-in-the-loop or hardware-in-the-loop tests on large distribution test feeders for a range of use cases, including testing functions of advanced distribution management systems against a simulated distribution system. In the future, the developers intend to release the conversion tool as open source to enable use by others.

Evolving impact of Ada on a production software environment

Science.gov (United States)

Mcgarry, F.; Esker, L.; Quimby, K.

1988-01-01

Many aspects of software development with Ada have evolved as our Ada development environment has matured and personnel have become more experienced in the use of Ada. The Software Engineering Laboratory (SEL) has seen differences in the areas of cost, reliability, reuse, size, and use of Ada features. A first Ada project can be expected to cost about 30 percent more than an equivalent FORTRAN project. However, the SEL has observed significant improvements over time as a development environment progresses to second and third uses of Ada. The reliability of Ada projects is initially similar to what is expected in a mature FORTRAN environment. However, with time, one can expect to gain improvements as experience with the language increases. Reuse is one of the most promising aspects of Ada. The proportion of reusable Ada software on our Ada projects exceeds the proportion of reusable FORTRAN software on our FORTRAN projects. This result was noted fairly early in our Ada projects, and experience shows an increasing trend over time.

Development and Field Test of a Real-Time Database in the Korean Smart Distribution Management System

Directory of Open Access Journals (Sweden)

Sang-Yun Yun

2014-03-01

Full Text Available Recently, a distribution management system (DMS that can conduct periodical system analysis and control by mounting various applications programs has been actively developed. In this paper, we summarize the development and demonstration of a database structure that can perform real-time system analysis and control of the Korean smart distribution management system (KSDMS. The developed database structure consists of a common information model (CIM-based off-line database (DB, a physical DB (PDB for DB establishment of the operating server, a real-time DB (RTDB for real-time server operation and remote terminal unit data interconnection, and an application common model (ACM DB for running application programs. The ACM DB for real-time system analysis and control of the application programs was developed by using a parallel table structure and a link list model, thereby providing fast input and output as well as high execution speed of application programs. Furthermore, the ACM DB was configured with hierarchical and non-hierarchical data models to reflect the system models that increase the DB size and operation speed through the reduction of the system, of which elements were unnecessary for analysis and control. The proposed database model was implemented and tested at the Gochaing and Jeju offices using a real system. Through data measurement of the remote terminal units, and through the operation and control of the application programs using the measurement, the performance, speed, and integrity of the proposed database model were validated, thereby demonstrating that this model can be applied to real systems.

Self-Organization in Embedded Real-Time Systems

CERN Document Server

Brinkschulte, Uwe; Rettberg, Achim

2013-01-01

This book describes the emerging field of self-organizing, multicore, distributed and real-time embedded systems.  Self-organization of both hardware and software can be a key technique to handle the growing complexity of modern computing systems. Distributed systems running hundreds of tasks on dozens of processors, each equipped with multiple cores, requires self-organization principles to ensure efficient and reliable operation. This book addresses various, so-called Self-X features such as self-configuration, self-optimization, self-adaptation, self-healing and self-protection. Presents open components for embedded real-time adaptive and self-organizing applications; Describes innovative techniques in: scheduling, memory management, quality of service, communications supporting organic real-time applications; Covers multi-/many-core embedded systems supporting real-time adaptive systems and power-aware, adaptive hardware and software systems; Includes case studies of open embedded real-time self-organizi...

Classic-Ada(TM)

Science.gov (United States)

Valley, Lois

1989-01-01

The SPS product, Classic-Ada, is a software tool that supports object-oriented Ada programming with powerful inheritance and dynamic binding. Object Oriented Design (OOD) is an easy, natural development paradigm, but it is not supported by Ada. Following the DOD Ada mandate, SPS developed Classic-Ada to provide a tool which supports OOD and implements code in Ada. It consists of a design language, a code generator and a toolset. As a design language, Classic-Ada supports the object-oriented principles of information hiding, data abstraction, dynamic binding, and inheritance. It also supports natural reuse and incremental development through inheritance, code factoring, and Ada, Classic-Ada, dynamic binding and static binding in the same program. Only nine new constructs were added to Ada to provide object-oriented design capabilities. The Classic-Ada code generator translates user application code into fully compliant, ready-to-run, standard Ada. The Classic-Ada toolset is fully supported by SPS and consists of an object generator, a builder, a dictionary manager, and a reporter. Demonstrations of Classic-Ada and the Classic-Ada Browser were given at the workshop.

Ada (Trade Name) Bibliography. Volume 3.

Science.gov (United States)

1986-02-01

access to shared resources by concurrently callable procedures. Both rely on queues to achieve serialization, but calls on monitor procedures are...DOCUMENT CITATIONS ADA AS A PROGRAM DESCRIPTION LANGUAGE (PDL): A PROJECT SOFTW ARE MANAGEMENT PERSPECTIVE BOND , RODNEY M. DOCUMENT NUMBER: 6141 TYPE...HONEYWELL BULL-RESEARCH CTR,GRENOBLE,CEDEX,FRANCE 2548 -01 ADA, ABSTRACT DATA TYPES AND DISTRIBUTED DATABASES TRANSACTIONS BOND , RODNEYM., NONAFFILIATED 6141

Palantiri: a distributed real-time database system for process control

International Nuclear Information System (INIS)

Tummers, B.J.; Heubers, W.P.J.

1992-01-01

The medium-energy accelerator MEA, located in Amsterdam, is controlled by a heterogeneous computer network. A large real-time database contains the parameters involved in the control of the accelerator and the experiments. This database system was implemented about ten years ago and has since been extended several times. In response to increased needs the database system has been redesigned. The new database environment, as described in this paper, consists out of two new concepts: (1) A Palantir which is a per machine process that stores the locally declared data and forwards all non local requests for data access to the appropriate machine. It acts as a storage device for data and a looking glass upon the world. (2) Golems: working units that define the data within the Palantir, and that have knowledge of the hardware they control. Applications access the data of a Golem by name (which do resemble Unix path names). The palantir that runs on the same machine as the application handles the distribution of access requests. This paper focuses on the Palantir concept as a distributed data storage and event handling device for process control. (author)

The Case For Prediction-based Best-effort Real-time Systems.

Science.gov (United States)

1999-01-01

Real - time Systems Peter A. Dinda Loukas Kallivokas January...DISTRIBUTION STATEMENT A Approved for Public Release Distribution Unlimited DTIG QUALBR DISSECTED X The Case For Prediction-based Best-effort Real - time Systems Peter...Mellon University Pittsburgh, PA 15213 A version of this paper appeared in the Seventh Workshop on Parallel and Distributed Real - Time Systems

Safe and Efficient Support for Embeded Multi-Processors in ADA

Science.gov (United States)

Ruiz, Jose F.

2010-08-01

New software demands increasing processing power, and multi-processor platforms are spreading as the answer to achieve the required performance. Embedded real-time systems are also subject to this trend, but in the case of real-time mission-critical systems, the properties of reliability, predictability and analyzability are also paramount. The Ada 2005 language defined a subset of its tasking model, the Ravenscar profile, that provides the basis for the implementation of deterministic and time analyzable applications on top of a streamlined run-time system. This Ravenscar tasking profile, originally designed for single processors, has proven remarkably useful for modelling verifiable real-time single-processor systems. This paper proposes a simple extension to the Ravenscar profile to support multi-processor systems using a fully partitioned approach. The implementation of this scheme is simple, and it can be used to develop applications amenable to schedulability analysis.

CLIPS/Ada: An Ada-based tool for building expert systems

Science.gov (United States)

White, W. A.

1990-01-01

Clips/Ada is a production system language and a development environment. It is functionally equivalent to the CLIPS tool. CLIPS/Ada was developed in order to provide a means of incorporating expert system technology into projects where the use of the Ada language had been mandated. A secondary purpose was to glean information about the Ada language and its compilers. Specifically, whether or not the language and compilers were mature enough to support AI applications. The CLIPS/Ada tool is coded entirely in Ada and is designed to be used by Ada systems that require expert reasoning.

A Real-Time, Distributed and Context-Aware System for Managing Solidarity Campaigns

Directory of Open Access Journals (Sweden)

Ana OLIVEIRA ALVES

2016-05-01

Full Text Available We present a project implemented on the field which has two separate strands, one refers on collecting crowd sensing data through mobile apps where context is (near automatically induced, another is related to a practical application of this method in a real time system to manage solidarity campaigns in collecting goods. Here, we cover both parts, we applied an experimental setup and obtained results and insights in a third sector institution, Caritas Diocesana of Coimbra[1], a non-profit organization part of Caritas[2]. As main contribution, we propose a distributed architecture for Mobile Crowd Sensing able not only to allow real time inventory through simultaneous campaigns but also it gives feedback to volunteers in order to instantly acquire information about which categories of goods are more needed[1] http://www.caritas.pt/site/nacional/ Portuguese Website (last visited in October 2015[2] http://www.caritas.eu/ (last visited in October 2015

Real-time Energy Resource Scheduling considering a Real Portuguese Scenario

DEFF Research Database (Denmark)

Silva, Marco; Sousa, Tiago; Morais, Hugo

2014-01-01

The development in power systems and the introduction of decentralized gen eration and Electric Vehicles (EVs), both connected to distribution networks, represents a major challenge in the planning and operation issues. This new paradigm requires a new energy resources management approach which...... scheduling in smart grids, considering day - ahead, hour - ahead and real - time scheduling. The case study considers a 33 - bus distribution network with high penetration of distributed energy resources . The wind generation profile is base d o n a rea l Portuguese wind farm . Four scenarios are presented...... taking into account 0, 1, 2 and 5 periods (hours or minutes) ahead of the scheduling period in the hour - ahead and real - time scheduling...

Development of Ada language control software for the NASA power management and distribution test bed

Science.gov (United States)

Wright, Ted; Mackin, Michael; Gantose, Dave

1989-01-01

The Ada language software developed to control the NASA Lewis Research Center's Power Management and Distribution testbed is described. The testbed is a reduced-scale prototype of the electric power system to be used on space station Freedom. It is designed to develop and test hardware and software for a 20-kHz power distribution system. The distributed, multiprocessor, testbed control system has an easy-to-use operator interface with an understandable English-text format. A simple interface for algorithm writers that uses the same commands as the operator interface is provided, encouraging interactive exploration of the system.

Internet-accessible real-time weather information system

Digital Repository Service at National Institute of Oceanography (India)

Desai, R.G.P.; Joseph, A.; Desa, E.; Mehra, P.; Desa, E.; Gouveia, A.D.

An internet-accessible real-time weather information system has been developed. This system provides real-time accessibility to weather information from a multitude of spatially distributed weather stations. The Internet connectivity also offers...

Definition of an auxiliary processor dedicated to real-time operating system kernels

Science.gov (United States)

Halang, Wolfgang A.

1988-01-01

In order to increase the efficiency of process control data processing, it is necessary to enhance the productivity of real time high level languages and to automate the task administration, because presently 60 percent or more of the applications are still programmed in assembly languages. This may be achieved by migrating apt functions for the support of process control oriented languages into the hardware, i.e., by new architectures. Whereas numerous high level languages have already been defined or realized, there are no investigations yet on hardware assisted implementation of real time features. The requirements to be fulfilled by languages and operating systems in hard real time environment are summarized. A comparison of the most prominent languages, viz. Ada, HAL/S, LTR, Pearl, as well as the real time extensions of FORTRAN and PL/1, reveals how existing languages meet these demands and which features still need to be incorporated to enable the development of reliable software with predictable program behavior, thus making it possible to carry out a technical safety approval. Accordingly, Pearl proved to be the closest match to the mentioned requirements.

Sin casa, otra vez: la Cañada Real frente a la exclusión habitacional

OpenAIRE

Pastor Hernández, Virginia

2018-01-01

Se estima que en la Comunidad de Madrid siguen viviendo más de 9000 personas en núcleos chabolistas. El objetivo del trabajo es visibilizar la situación de exclusión habitacional de los asentamientos auto-producidos, y más concretamente el de la Cañada Real Galiana. Para ello, se ha revisado la bibliografía existente sobre el contexto y el concepto de exclusión habitacional. A partir de este marco teórico se ha elaborado un marco analítico que se ha aplicado al caso de estudio de la Cañad...

A real-time networked camera system : a scheduled distributed camera system reduces the latency

NARCIS (Netherlands)

Karatoy, H.

2012-01-01

This report presents the results of a Real-time Networked Camera System, com-missioned by the SAN Group in TU/e. Distributed Systems are motivated by two reasons, the first reason is the physical environment as a requirement and the second reason is to provide a better Quality of Service (QoS). This

Distributed Resource Energy Analysis and Management System (DREAMS) Development for Real-time Grid Operations

Energy Technology Data Exchange (ETDEWEB)

Nakafuji, Dora [Hawaiian Electric Company, Honululu, HI (United States); Gouveia, Lauren [Hawaiian Electric Company, Honululu, HI (United States)

2016-10-24

This project supports development of the next generation, integrated energy management infrastructure (EMS) able to incorporate advance visualization of behind-the-meter distributed resource information and probabilistic renewable energy generation forecasts to inform real-time operational decisions. The project involves end-users and active feedback from an Utility Advisory Team (UAT) to help inform how information can be used to enhance operational functions (e.g. unit commitment, load forecasting, Automatic Generation Control (AGC) reserve monitoring, ramp alerts) within two major EMS platforms. Objectives include: Engaging utility operations personnel to develop user input on displays, set expectations, test and review; Developing ease of use and timeliness metrics for measuring enhancements; Developing prototype integrated capabilities within two operational EMS environments; Demonstrating an integrated decision analysis platform with real-time wind and solar forecasting information and timely distributed resource information; Seamlessly integrating new 4-dimensional information into operations without increasing workload and complexities; Developing sufficient analytics to inform and confidently transform and adopt new operating practices and procedures; Disseminating project lessons learned through industry sponsored workshops and conferences;Building on collaborative utility-vendor partnership and industry capabilities

Developments in architecture for real-time data systems

International Nuclear Information System (INIS)

Heath, R.L.; Myers, W.R.

1975-01-01

Real-time data systems typically operate at two levels: a fast-response instrument-oriented level for data acquisition and control, and a slow human-oriented level for interaction and computation. Traditional minicomputer data systems support real-time applications by implementation of background/foreground software. Recent developments in computer technology including microprocessors enable the functional organization of hardware in distributed or hierarchical form to provide new system structures for real-time requirements. Examples of systems with distributed architecture will be discussed in detail

Conversion and Validation of Distribution System Model from a QSTS-Based Tool to a Real-Time Dynamic Phasor Simulator: Preprint

Energy Technology Data Exchange (ETDEWEB)

Chamana, Manohar; Prabakar, Kumaraguru; Palmintier, Bryan; Baggu, Murali M.

2017-04-11

A software process is developed to convert distribution network models from a quasi-static time-series tool (OpenDSS) to a real-time dynamic phasor simulator (ePHASORSIM). The description of this process in this paper would be helpful for researchers who intend to perform similar conversions. The converter could be utilized directly by users of real-time simulators who intend to perform software-in-the-loop or hardware-in-the-loop tests on large distribution test feeders for a range of use cases, including testing functions of advanced distribution management systems against a simulated distribution system. In the future, the developers intend to release the conversion tool as open source to enable use by others.

A distributed approach for optimizing cascaded classifier topologies in real-time stream mining systems.

Science.gov (United States)

Foo, Brian; van der Schaar, Mihaela

2010-11-01

In this paper, we discuss distributed optimization techniques for configuring classifiers in a real-time, informationally-distributed stream mining system. Due to the large volume of streaming data, stream mining systems must often cope with overload, which can lead to poor performance and intolerable processing delay for real-time applications. Furthermore, optimizing over an entire system of classifiers is a difficult task since changing the filtering process at one classifier can impact both the feature values of data arriving at classifiers further downstream and thus, the classification performance achieved by an ensemble of classifiers, as well as the end-to-end processing delay. To address this problem, this paper makes three main contributions: 1) Based on classification and queuing theoretic models, we propose a utility metric that captures both the performance and the delay of a binary filtering classifier system. 2) We introduce a low-complexity framework for estimating the system utility by observing, estimating, and/or exchanging parameters between the inter-related classifiers deployed across the system. 3) We provide distributed algorithms to reconfigure the system, and analyze the algorithms based on their convergence properties, optimality, information exchange overhead, and rate of adaptation to non-stationary data sources. We provide results using different video classifier systems.

The Role of G22 A Adenosine Deaminase 1 Gene Polymorphism and the Activities of ADA Isoenzymes in Fertile and Infertile Men.

Science.gov (United States)

Fattahi, Amir; Khodadadi, Iraj; Amiri, Iraj; Latifi, Zeinab; Ghorbani, Marzieh; Tavilani, Heidar

2015-10-01

To evaluate frequency distribution of adenosine deaminase 1 (ADA1) G22 A alleles and genotypes in fertile and infertile men. In this study we evaluate frequency distribution of ADA1 G22 A alleles and genotypes in 200 fertile and 200 infertile men. The polymerase chain reaction-restriction fragment length polymorphism technique was used for determining ADA1 G22 A variants. In addition, ADA isoenzymes activities (ADA1 and ADA2) were measured using colorimetric method. The frequency of GG genotype was significantly higher and GA genotype was lower in infertile males compared with fertile men (P = .048 and P = .045, respectively). However, there was not any noticeable difference in allele distribution between groups (P >.05). Based on logistic regression analysis, the GA genotype has a protective role and can decrease the risk of male infertility 1.7 times (P = .046). There were significantly higher activities of ADAT and its isoenzymes in infertile males compared with fertile men (P ADA1 activity with GG genotype was higher than GA carriers in all population (P = .001). Our results revealed that the activity of ADA isoenzymes and distribution of ADA1 G22 A genotypes were different among fertile and infertile men and more likely the GA genotype, which had lower ADA1 activity and was higher in fertile men is a protective factor against infertility. Copyright © 2015 Elsevier Inc. All rights reserved.

Review of Real-time Electricity Markets for Integrating Distributed Energy Resources and Demand Response

DEFF Research Database (Denmark)

Wang, Qi; Zhang, Chunyu; Ding, Yi

2015-01-01

The high penetration of both Distributed Energy Resources (DER) and Demand Response (DR) in modern power systems requires a sequence of advanced strategies and technologies for maintaining system reliability and flexibility. Real-time electricity markets (RTM) are the nondiscriminatory transaction...... platforms for providing necessary balancing services, where the market clearing (nodal or zonal prices depending on markets) is very close to real time operations of power systems. One of the primary functions of RTMs in modern power systems is establishing an efficient and effective mechanism for small DER...... and DR to participate in balancing market transactions, while handling their meteorological or intermittent characteristics, facilitating asset utilization, and stimulating their active responses. Consequently, RTMs are dedicated to maintaining the flexibility and reliability of power systems. This paper...

ADAS Update and Maintainability

Science.gov (United States)

Watson, Leela R.

2010-01-01

Since 2000, both the National Weather Service Melbourne (NWS MLB) and the Spaceflight Meteorology Group (SMG) have used a local data integration system (LOIS) as part of their forecast and warning operations. The original LOIS was developed by the Applied Meteorology Unit (AMU) in 1998 (Manobianco and Case 1998) and has undergone subsequent improvements. Each has benefited from three-dimensional (3-D) analyses that are delivered to forecasters every 15 minutes across the peninsula of Florida. The intent is to generate products that enhance short-range weather forecasts issued in support of NWS MLB and SMG operational requirements within East Central Florida. The current LDIS uses the Advanced Regional Prediction System (ARPS) Data Analysis System (AD AS) package as its core, which integrates a wide variety of national, regional, and local observational data sets. It assimilates all available real-time data within its domain and is run at a finer spatial and temporal resolution than current national or regional-scale analysis packages. As such, it provides local forecasters with a more comprehensive understanding of evolving fine-scale weather features. Over the years, the LDIS has become problematic to maintain since it depends on AMU-developed shell scripts that were written for an earlier version of the ADAS software. The goals of this task were to update the NWS MLB/SMG LDIS with the latest version of ADAS, incorporate new sources of observational data, and upgrade and modify the AMU-developed shell scripts written to govern the system. In addition, the previously developed ADAS graphical user interface (GUI) was updated. Operationally, these upgrades will result in more accurate depictions of the current local environment to help with short-range weather forecasting applications, while also offering an improved initialization for local versions of the Weather Research and Forecasting (WRF) model used by both groups.

GRASP/Ada 95: Reverse Engineering Tools for Ada

Science.gov (United States)

Cross, James H., II

1996-01-01

The GRASP/Ada project (Graphical Representations of Algorithms, Structures, and Processes for Ada) has successfully created and prototyped an algorithmic level graphical representation for Ada software, the Control Structure Diagram (CSD), and a new visualization for a fine-grained complexity metric called the Complexity Profile Graph (CPG). By synchronizing the CSD and the CPG, the CSD view of control structure, nesting, and source code is directly linked to the corresponding visualization of statement level complexity in the CPG. GRASP has been integrated with GNAT, the GNU Ada 95 Translator to provide a comprehensive graphical user interface and development environment for Ada 95. The user may view, edit, print, and compile source code as a CSD with no discernible addition to storage or computational overhead. The primary impetus for creation of the CSD was to improve the comprehension efficiency of Ada software and, as a result, improve reliability and reduce costs. The emphasis has been on the automatic generation of the CSD from Ada 95 source code to support reverse engineering and maintenance. The CSD has the potential to replace traditional prettyprinted Ada source code. The current update has focused on the design and implementation of a new Motif compliant user interface, and a new CSD generator consisting of a tagger and renderer. The Complexity Profile Graph (CPG) is based on a set of functions that describes the context, content, and the scaling for complexity on a statement by statement basis. When combined graphicafly, the result is a composite profile of complexity for the program unit. Ongoing research includes the development and refinement of the associated functions, and the development of the CPG generator prototype. The current Version 5.0 prototype provides the capability for the user to generate CSDs and CPGs from Ada 95 source code in a reverse engineering as well as forward engineering mode with a level of flexibility suitable for

Real-Time Impact Visualization Inspection of Aerospace Composite Structures with Distributed Sensors.

Science.gov (United States)

Si, Liang; Baier, Horst

2015-07-08

For the future design of smart aerospace structures, the development and application of a reliable, real-time and automatic monitoring and diagnostic technique is essential. Thus, with distributed sensor networks, a real-time automatic structural health monitoring (SHM) technique is designed and investigated to monitor and predict the locations and force magnitudes of unforeseen foreign impacts on composite structures and to estimate in real time mode the structural state when impacts occur. The proposed smart impact visualization inspection (IVI) technique mainly consists of five functional modules, which are the signal data preprocessing (SDP), the forward model generator (FMG), the impact positioning calculator (IPC), the inverse model operator (IMO) and structural state estimator (SSE). With regard to the verification of the practicality of the proposed IVI technique, various structure configurations are considered, which are a normal CFRP panel and another CFRP panel with "orange peel" surfaces and a cutout hole. Additionally, since robustness against several background disturbances is also an essential criterion for practical engineering demands, investigations and experimental tests are carried out under random vibration interfering noise (RVIN) conditions. The accuracy of the predictions for unknown impact events on composite structures using the IVI technique is validated under various structure configurations and under changing environmental conditions. The evaluated errors all fall well within a satisfactory limit range. Furthermore, it is concluded that the IVI technique is applicable for impact monitoring, diagnosis and assessment of aerospace composite structures in complex practical engineering environments.

VERSE - Virtual Equivalent Real-time Simulation

Science.gov (United States)

Zheng, Yang; Martin, Bryan J.; Villaume, Nathaniel

2005-01-01

Distributed real-time simulations provide important timing validation and hardware in the- loop results for the spacecraft flight software development cycle. Occasionally, the need for higher fidelity modeling and more comprehensive debugging capabilities - combined with a limited amount of computational resources - calls for a non real-time simulation environment that mimics the real-time environment. By creating a non real-time environment that accommodates simulations and flight software designed for a multi-CPU real-time system, we can save development time, cut mission costs, and reduce the likelihood of errors. This paper presents such a solution: Virtual Equivalent Real-time Simulation Environment (VERSE). VERSE turns the real-time operating system RTAI (Real-time Application Interface) into an event driven simulator that runs in virtual real time. Designed to keep the original RTAI architecture as intact as possible, and therefore inheriting RTAI's many capabilities, VERSE was implemented with remarkably little change to the RTAI source code. This small footprint together with use of the same API allows users to easily run the same application in both real-time and virtual time environments. VERSE has been used to build a workstation testbed for NASA's Space Interferometry Mission (SIM PlanetQuest) instrument flight software. With its flexible simulation controls and inexpensive setup and replication costs, VERSE will become an invaluable tool in future mission development.

Implementering Run-time Evaluation of Distributed Timing Constraints in a Micro Kernel

DEFF Research Database (Denmark)

Kristensen, C.H.; Drejer, N.; Nielsen, Jens Frederik Dalsgaard

In the present paper we describe a solution to the problem of implementing time-optimal evaluation of timing constraints in distributed real-time systems......In the present paper we describe a solution to the problem of implementing time-optimal evaluation of timing constraints in distributed real-time systems...

Timing System Solution for MedAustron; Real-time Event and Data Distribution Network

CERN Document Server

Štefanič, R; Dedič, J; Gutleber, J; Moser, R

2011-01-01

MedAustron is an ion beam research and therapy centre under construction in Wiener Neustadt, Austria. The facility features a synchrotron particle accelerator for light ions. The timing system for this class of accelerators has been developed in close collaboration between MedAustron and Cosylab. Mitigating economical and technological risks, we have chosen a proven, widely used Micro Research Finland (MRF) timing equipment and redesigned its FPGA firmware, extending its high-logic services above transport layer, as required by machine specifics. We obtained a generic real-time broadcast network for coordinating actions of a compact, pulse-to-pulse modulation based particle accelerator. High-level services include support for virtual accelerators and a rich selection of event response mechanisms. The system uses a combination of a real-time link for downstream events and a non-real-time link for upstream messaging and non time-critical communication. It comes with National Instruments LabVI...

Assessing the benefits of residential demand response in a real time distribution energy market

International Nuclear Information System (INIS)

Siano, Pierluigi; Sarno, Debora

2016-01-01

Highlights: • A new probabilistic methodology, integrating DR in a distribution energy market is proposed. • The method can alleviate distribution network congestions. • This method based on D-LMPs allows cost savings for end-user customers. • Innovative thermal and shiftable loads Real Time control algorithms are also presented. - Abstract: In the field of electricity distribution networks and with the advent of smart grids and microgrids, the use of Distribution Locational Marginal Price (D-LMPs) in a Real Time (RT) distribution market managed by a Distribution System Operator (DSO) is discussed in presence of empowered residential end-users that are able to bid for energy by a demand aggregator while following Demand Response (DR) initiatives. Each customer is provided by a transactive controller, which reads the locational market signals and answers with a bid taking into account the user preferences about some appliances involved in DR activities and controlled by smart plugs-in. In particular, Heating Ventilation and Air Conditioning (HVAC) appliances and shiftable loads are controlled so that their consumption profile can be modified according to the price of energy. In order to assess the effectiveness of the proposed method in terms of energy and cost saving, an innovative probabilistic methodology for evaluating the impact of residential DR choices considering uncertainties related to load demand, user preferences, environmental conditions, house thermal behavior and wholesale market trends has been proposed. The uncertainties related to the stochastic variations of the variables involved are modeled by using the Monte Carlo Simulation (MCS) method. The combination of MCS and RT distribution market simulation based on D-LMPs are used to assess the operation and impact of the DR method over one month. Simulations results on an 84-buses distribution network confirmed that the proposed method allows saving costs for residential end-users and making

Infrared Tomography: Data Distribution System for Real-time Mass Flow Rate Measurement

Directory of Open Access Journals (Sweden)

Ruzairi Abdul Rahim

2007-06-01

Full Text Available The system developed in this research has the objective of measuring mass flow rate in an online mode. If a single computer is used as data processing unit, a longer time is needed to produce a measurement result. In the research carried out by previous researcher shows about 11.2 seconds is needed to obtain one mass flow rate result in the offline mode (using offline data. This insufficient real-time result will cause problems in a feedback control process when applying the system on industrial plants. To increase the refreshing rate of the measurement result, an investigation on a data distribution system is performed to replace the existing data processing unit.

Integration of MDSplus in real-time systems

International Nuclear Information System (INIS)

Luchetta, A.; Manduchi, G.; Taliercio, C.

2006-01-01

RFX-mod makes extensive usage of real-time systems for feedback control and uses MDSplus to interface them to the main Data Acquisition system. For this purpose, the core of MDSplus has been ported to VxWorks, the operating system used for real-time control in RFX. Using this approach, it is possible to integrate real-time systems, but MDSplus is used only for non-real-time tasks, i.e. those tasks which are executed before and after the pulse and whose performance does not affect the system time constraints. More extensive use of MDSplus in real-time systems is foreseen, and a real-time layer for MDSplus is under development, which will provide access to memory-mapped pulse files, shared by the tasks running on the same CPU. Real-time communication will also be integrated in the MDSplus core to provide support for distributed memory-mapped pulse files

SAFCM: A Security-Aware Feedback Control Mechanism for Distributed Real-Time Embedded Systems

DEFF Research Database (Denmark)

Ma, Yue; Jiang, Wei; Sang, Nan

2012-01-01

Distributed Real-time Embedded (DRE) systems are facing great challenges in networked, unpredictable and especially unsecured environments. In such systems, there is a strong need to enforce security on distributed computing nodes in order to guard against potential threats, while satisfying......-time systems, a multi-input multi-output feedback loop is designed and a model predictive controller is deployed based on an equation model that describes the dynamic behavior of the DRE systems. This control loop uses security level scaling to globally control the CPU utilization and security performance...... for the whole system. We propose a "security level" metric based on an evolution of cryptography algorithms used in embedded systems. Experimental results demonstrate that SAFCM not only has the excellent adaptivity compared to open-loop mechanism, but also has a better overall performance than PID control...

Load sharing in distributed real-time systems with state-change broadcasts

Science.gov (United States)

Shin, Kang G.; Chang, Yi-Chieh

1989-01-01

A decentralized dynamic load-sharing (LS) method based on state-change broadcasts is proposed for a distributed real-time system. Whenever the state of a node changes from underloaded to fully loaded and vice versa, the node broadcasts this change to a set of nodes, called a buddy set, in the system. The performance of the method is evaluated with both analytic modeling and simulation. It is modeled first by an embedded Markov chain for which numerical solutions are derived. The model solutions are then used to calculate the distribution of queue lengths at the nodes and the probability of meeting task deadlines. The analytical results show that buddy sets of 10 nodes outperform those of less than 10 nodes, and the incremental benefit gained from increasing the buddy set size beyond 15 nodes is insignificant. These and other analytical results are verified by simulation. The proposed LS method is shown to meet task deadlines with a very high probability.

Storm blueprints patterns for distributed real-time computation

CERN Document Server

Goetz, P Taylor

2014-01-01

A blueprints book with 10 different projects built in 10 different chapters which demonstrate the various use cases of storm for both beginner and intermediate users, grounded in real-world example applications.Although the book focuses primarily on Java development with Storm, the patterns are more broadly applicable and the tips, techniques, and approaches described in the book apply to architects, developers, and operations.Additionally, the book should provoke and inspire applications of distributed computing to other industries and domains. Hadoop enthusiasts will also find this book a go

Real-Time MENTAT programming language and architecture

Science.gov (United States)

Grimshaw, Andrew S.; Silberman, Ami; Liu, Jane W. S.

1989-01-01

Real-time MENTAT, a programming environment designed to simplify the task of programming real-time applications in distributed and parallel environments, is described. It is based on the same data-driven computation model and object-oriented programming paradigm as MENTAT. It provides an easy-to-use mechanism to exploit parallelism, language constructs for the expression and enforcement of timing constraints, and run-time support for scheduling and exciting real-time programs. The real-time MENTAT programming language is an extended C++. The extensions are added to facilitate automatic detection of data flow and generation of data flow graphs, to express the timing constraints of individual granules of computation, and to provide scheduling directives for the runtime system. A high-level view of the real-time MENTAT system architecture and programming language constructs is provided.

Efficient Ada multitasking on a RISC register window architecture

Science.gov (United States)

Kearns, J. P.; Quammen, D.

1987-01-01

This work addresses the problem of reducing context switch overhead on a processor which supports a large register file - a register file much like that which is part of the Berkeley RISC processors and several other emerging architectures (which are not necessarily reduced instruction set machines in the purest sense). Such a reduction in overhead is particularly desirable in a real-time embedded application, in which task-to-task context switch overhead may result in failure to meet crucial deadlines. A storage management technique by which a context switch may be implemented as cheaply as a procedure call is presented. The essence of this technique is the avoidance of the save/restore of registers on the context switch. This is achieved through analysis of the static source text of an Ada tasking program. Information gained during that analysis directs the optimized storage management strategy for that program at run time. A formal verification of the technique in terms of an operational control model and an evaluation of the technique's performance via simulations driven by synthetic Ada program traces are presented.

Unidata Internet Data Distribution (IDD) and THematic Real-time Environmental Distributed Data Services (THREDDS)

Science.gov (United States)

Domenico, B.

2001-12-01

Universities across the nation are transforming their teaching and research efforts through increased use of a rapidly expanding menu of environmental data. With funding from the Division of Atmospheric Sciences (ATM ) of the National Science Foundation (NSF), the Unidata Program is playing a central role in this transformation by enabling universities to employ innovative computing and networking technologies to acquire such data sets in real-time and use them routinely in their classrooms and research labs. Working with the Unidata Program Center (UPC), the Unidata community, comprising over 140 departments, has built a national Internet Data Distribution (IDD ) system. The IDD allows users to "subscribe" to certain sets of data products; IDD servers then deliver the requested data to their local servers as soon as they are available from the source. With the initial national implementation in 1994, the IDD may have been the original example of Internet "push" technology. It now provides the reliability, flexibility, and efficiency required by participating institutions. As the underlying Internet technology evolves, we anticipate dramatic increases in the volume of data delivered. We plan to augment the system to better serve disciplines outside the atmospheric sciences and to incorporate anticipated new networking technologies to minimize the impact of the IDD on the underlying network. Unidata has recently undertaken a new initiative called THREDDS (THematic Real-time Environmental Distributed Data Services) under a grant from the NSF Division of Undergraduate Education NSDL (National Science, Math, Engineering, Technology Education Digital Library). The goal of THREDDs is to make it possible for students, educators and researchers to publish, contribute, find, and interact with data relating to the Earth system in a convenient, effective, and integrated fashion. Just as the World Wide Web and digital-library technologies have simplified the process of

Evaluation of a Connectionless NoC for a Real-Time Distributed Shared Memory Many-Core System

NARCIS (Netherlands)

Rutgers, J.H.; Bekooij, Marco Jan Gerrit; Smit, Gerardus Johannes Maria

2012-01-01

Real-time embedded systems like smartphones tend to comprise an ever increasing number of processing cores. For scalability and the need for guaranteed performance, the use of a connection-oriented network-on-chip (NoC) is advocated. Furthermore, a distributed shared memory architecture is preferred

Real-time data access layer for MDSplus

International Nuclear Information System (INIS)

Manduchi, G.; Luchetta, A.; Taliercio, C.; Fredian, T.; Stillerman, J.

2008-01-01

Recent extensions to MDSplus allow data handling in long discharges and provide a real-time data access and communication layer. The real-time data access layer is an additional component of MDSplus: it is possible to use the traditional MDSplus API during normal operation, and to select a subset of data items to be used in real time. Real-time notification is provided by a communication layer using a publish-subscribe pattern. The notification covers processes sharing the same data items even running on different machines, thus allowing the implementation of distributed control systems. The real-time data access layer has been developed for Windows, Linux, and VxWorks; it is currently being ported to Linux RTAI. In order to quantify the fingerprint of the presented system, the performance of the real-time access layer approach is compared with that of an ad hoc, manually optimized program in a sample real-time application

Real - time Optimization of Distributed Energy Storage System Operation Strategy Based on Peak Load Shifting

Science.gov (United States)

Wang, Qian; Lu, Guangqi; Li, Xiaoyu; Zhang, Yichi; Yun, Zejian; Bian, Di

2018-01-01

To take advantage of the energy storage system (ESS) sufficiently, the factors that the service life of the distributed energy storage system (DESS) and the load should be considered when establishing optimization model. To reduce the complexity of the load shifting of DESS in the solution procedure, the loss coefficient and the equal capacity ratio distribution principle were adopted in this paper. Firstly, the model was established considering the constraint conditions of the cycles, depth, power of the charge-discharge of the ESS, the typical daily load curves, as well. Then, dynamic programming method was used to real-time solve the model in which the difference of power Δs, the real-time revised energy storage capacity Sk and the permission error of depth of charge-discharge were introduced to optimize the solution process. The simulation results show that the optimized results was achieved when the load shifting in the load variance was not considered which means the charge-discharge of the energy storage system was not executed. In the meantime, the service life of the ESS would increase.

Immunologic reconstitution during PEG-ADA therapy in an unusual mosaic ADA deficient patient.

Science.gov (United States)

Liu, Ping; Santisteban, Ines; Burroughs, Lauri M; Ochs, Hans D; Torgerson, Troy R; Hershfield, Michael S; Rawlings, David J; Scharenberg, Andrew M

2009-02-01

We report detailed genetic and immunologic studies in a patient diagnosed with adenosine deaminase (ADA) deficiency and combined immune deficiency at age 5 years. At the time of diagnosis, although all other lymphocyte subsets were depleted, circulating CD8(+) T cells with a terminally differentiated phenotype were abundant and expressed normal ADA activity due to a reversion mutation in a CD8(+) T cell or precursor. Over the first 9 months of replacement therapy with PEG-ADA, the patient steadily accumulated mature naïve CD4(+) and CD8(+) T cells, as well as CD4(+)/FOXP3(+) regulatory T cells, consistent with restoration of a functional cellular immune system. While CD19(+) naïve B cells also accumulated in response to PEG-ADA therapy, a high proportion of these B cells exhibited an immature surface marker phenotype even after 9 months, and immunization with neoantigen bacteriophage varphiX174 demonstrated a markedly subnormal humoral immune response. Our observations in this single patient have important implications for gene therapy of human ADA deficiency, as they indicate that ADA expression within even a large circulating lymphocyte population may not be sufficient to support adequate immune reconstitution. They also suggest that an immature surface marker phenotype of the peripheral B cell compartment may be a useful surrogate marker for incomplete humoral immune reconstitution during enzyme replacement, and possibly other forms of hematopoietic cell therapies.

Continuous Real-time Measurements of Vertical Distribution of Magnetic Susceptibility In Soils

Science.gov (United States)

Petrovsky, E.; Hulka, Z.; Kapicka, A.; Magprox Team

Measurements of top-soil magnetic susceptibility are used in approximative outlining polluted areas. However, one of the serious limitations of the method is discrimina- tion between top-soil layers enhanced by atmospherically deposited anthropogenic particles from those dominated by natural particles migrating from magnetically-rich basement rocks. For this purpose, measurements of vertical distribution of magnetic susceptibility along soil profiles is one of the most effective ways in estimating the effect of lithogenic contribution. Up to now, in most cases soil cores have to be mea- sured in laboratory. This method is quite time consuming and does not allow flexible decision about the suitability of the measured site for surface magnetic mapping. In our contribution we will present a new device enabling continuous real-time measure- ments of vertical distribution of magnetic susceptibility directly in field, performed in holes after soil coring. The method is fast, yielding smooth curves (6 data points per 1 mm dept), at least as sensitive as laboratory methods available until now, and at- tached notebook enables direct, on-line control of the lithogenic versus anthropogenic contributions.

Generation of real-time global ionospheric map based on the global GNSS stations with only a sparse distribution

Science.gov (United States)

Li, Zishen; Wang, Ningbo; Li, Min; Zhou, Kai; Yuan, Yunbin; Yuan, Hong

2017-04-01

The Earth's ionosphere is part of the atmosphere stretching from an altitude of about 50 km to more than 1000 km. When the Global Navigation Satellite System (GNSS) signal emitted from a satellite travels through the ionosphere before reaches a receiver on or near the Earth surface, the GNSS signal is significantly delayed by the ionosphere and this delay bas been considered as one of the major errors in the GNSS measurement. The real-time global ionospheric map calculated from the real-time data obtained by global stations is an essential method for mitigating the ionospheric delay for real-time positioning. The generation of an accurate global ionospheric map generally depends on the global stations with dense distribution; however, the number of global stations that can produce the real-time data is very limited at present, which results that the generation of global ionospheric map with a high accuracy is very different when only using the current stations with real-time data. In view of this, a new approach is proposed for calculating the real-time global ionospheric map only based on the current stations with real-time data. This new approach is developed on the basis of the post-processing and the one-day predicted global ionospheric map from our research group. The performance of the proposed approach is tested by the current global stations with the real-time data and the test results are also compared with the IGS-released final global ionospheric map products.

Study of the Alsys implementation of the Catalogue of Interface Features and Options for the Ada language for 80386 Unix

Science.gov (United States)

Gibson, James S.; Barnes, Michael J.; Ostermiller, Daniel L.

1993-01-01

A set of programs was written to test the functionality and performance of the Alsys Ada implementation of the Catalogue of Interface Features and Options (CIFO), a set of optional Ada packages for real-time applications. No problems were found with the task id, preemption control, or shared-data packages. Minor problems were found with the dispatching control, dynamic priority, events, non-waiting entry call, semaphore, and scheduling packages. The Alsys implementation is derived mostly from Release 2 of the CIFO standard, but includes some of the features of Release 3 and some modifications unique to Alsys. Performance measurements show that the semaphore and shared-data features are an order-of-magnitude faster than the same mechanisms using an Ada rendezvous. The non-waiting entry call is slightly faster than a standard rendezvous. The existence of errors in the implementation, the incompleteness of the documentation from the published standard impair the usefulness of this implementation. Despite those short-comings, the Alsys CIFO implementation might be of value in the development of real-time applications.

Real time monitoring of water distribution in an operando fuel cell during transient states

Science.gov (United States)

Martinez, N.; Peng, Z.; Morin, A.; Porcar, L.; Gebel, G.; Lyonnard, S.

2017-10-01

The water distribution of an operating proton exchange membrane fuel cell (PEMFC) was monitored in real time by using Small Angle Neutron Scattering (SANS). The formation of liquid water was obtained simultaneously with the evolution of the water content inside the membrane. Measurements were performed when changing current with a time resolution of 10 s, providing insights on the kinetics of water management prior to the stationary phase. We confirmed that water distribution is strongly heterogeneous at the scale at of the whole Membrane Electrode Assembly. As already reported, at the local scale there is no straightforward link between the amounts of water present inside and outside the membrane. However, we show that the temporal evolutions of these two parameters are strongly correlated. In particular, the local membrane water content is nearly instantaneously correlated to the total liquid water content, whether it is located at the anode or cathode side. These results can help in optimizing 3D stationary diphasic models used to predict PEMFC water distribution.

Representing real time semantics for distributed application integration

NARCIS (Netherlands)

Poon, P.M.S.; Dillon, T.S.; Chang, E.; Feng, L.

Traditional real time system design and development are driven by technological requirements. With the ever growing complexity of requirements and the advances in software design, the alignment of focus has gradually been shifted to the perspective of business and industrial needs. This paper

Applications of an architecture design and assessment system (ADAS)

Science.gov (United States)

Gray, F. Gail; Debrunner, Linda S.; White, Tennis S.

1988-01-01

A new Architecture Design and Assessment System (ADAS) tool package is introduced, and a range of possible applications is illustrated. ADAS was used to evaluate the performance of an advanced fault-tolerant computer architecture in a modern flight control application. Bottlenecks were identified and possible solutions suggested. The tool was also used to inject faults into the architecture and evaluate the synchronization algorithm, and improvements are suggested. Finally, ADAS was used as a front end research tool to aid in the design of reconfiguration algorithms in a distributed array architecture.

Practical performance of real-time shot-noise measurement in continuous-variable quantum key distribution

Science.gov (United States)

Wang, Tao; Huang, Peng; Zhou, Yingming; Liu, Weiqi; Zeng, Guihua

2018-01-01

In a practical continuous-variable quantum key distribution (CVQKD) system, real-time shot-noise measurement (RTSNM) is an essential procedure for preventing the eavesdropper exploiting the practical security loopholes. However, the performance of this procedure itself is not analyzed under the real-world condition. Therefore, we indicate the RTSNM practical performance and investigate its effects on the CVQKD system. In particular, due to the finite-size effect, the shot-noise measurement at the receiver's side may decrease the precision of parameter estimation and consequently result in a tight security bound. To mitigate that, we optimize the block size for RTSNM under the ensemble size limitation to maximize the secure key rate. Moreover, the effect of finite dynamics of amplitude modulator in this scheme is studied and its mitigation method is also proposed. Our work indicates the practical performance of RTSNM and provides the real secret key rate under it.

Real-time systems

OpenAIRE

Badr, Salah M.; Bruztman, Donald P.; Nelson, Michael L.; Byrnes, Ronald Benton

1992-01-01

This paper presents an introduction to the basic issues involved in real-time systems. Both real-time operating sys and real-time programming languages are explored. Concurrent programming and process synchronization and communication are also discussed. The real-time requirements of the Naval Postgraduate School Autonomous Under Vehicle (AUV) are then examined. Autonomous underwater vehicle (AUV), hard real-time system, real-time operating system, real-time programming language, real-time sy...

Coordinated scheduling for dynamic real-time systems

Science.gov (United States)

Natarajan, Swaminathan; Zhao, Wei

1994-01-01

In this project, we addressed issues in coordinated scheduling for dynamic real-time systems. In particular, we concentrated on design and implementation of a new distributed real-time system called R-Shell. The design objective of R-Shell is to provide computing support for space programs that have large, complex, fault-tolerant distributed real-time applications. In R-shell, the approach is based on the concept of scheduling agents, which reside in the application run-time environment, and are customized to provide just those resource management functions which are needed by the specific application. With this approach, we avoid the need for a sophisticated OS which provides a variety of generalized functionality, while still not burdening application programmers with heavy responsibility for resource management. In this report, we discuss the R-Shell approach, summarize the achievement of the project, and describe a preliminary prototype of R-Shell system.

Energy and Reserve under Distributed Energy Resources Management—Day-Ahead, Hour-Ahead and Real-Time

Directory of Open Access Journals (Sweden)

Tiago Soares

2017-11-01

Full Text Available The increasing penetration of distributed energy resources based on renewable energy sources in distribution systems leads to a more complex management of power systems. Consequently, ancillary services become even more important to maintain the system security and reliability. This paper proposes and evaluates a generic model for day-ahead, intraday (hour-ahead and real-time scheduling, considering the joint optimization of energy and reserve in the scope of the virtual power player concept. The model aims to minimize the operation costs in the point of view of one aggregator agent taking into account the balance of the distribution system. For each scheduling stage, previous scheduling results and updated forecasts are considered. An illustrative test case of a distribution network with 33 buses, considering a large penetration of distribution energy resources allows demonstrating the benefits of the proposed model.

Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint

Energy Technology Data Exchange (ETDEWEB)

Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru; Hoke, Andy; Asano, Marc; Ueda, Reid; Nepal, Shaili

2017-06-15

As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digital testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.

D-MSR: A Distributed Network Management Scheme for Real-Time Monitoring and Process Control Applications in Wireless Industrial Automation

Science.gov (United States)

Zand, Pouria; Dilo, Arta; Havinga, Paul

2013-01-01

Current wireless technologies for industrial applications, such as WirelessHART and ISA100.11a, use a centralized management approach where a central network manager handles the requirements of the static network. However, such a centralized approach has several drawbacks. For example, it cannot cope with dynamicity/disturbance in large-scale networks in a real-time manner and it incurs a high communication overhead and latency for exchanging management traffic. In this paper, we therefore propose a distributed network management scheme, D-MSR. It enables the network devices to join the network, schedule their communications, establish end-to-end connections by reserving the communication resources for addressing real-time requirements, and cope with network dynamicity (e.g., node/edge failures) in a distributed manner. According to our knowledge, this is the first distributed management scheme based on IEEE 802.15.4e standard, which guides the nodes in different phases from joining until publishing their sensor data in the network. We demonstrate via simulation that D-MSR can address real-time and reliable communication as well as the high throughput requirements of industrial automation wireless networks, while also achieving higher efficiency in network management than WirelessHART, in terms of delay and overhead. PMID:23807687

D-MSR: a distributed network management scheme for real-time monitoring and process control applications in wireless industrial automation.

Science.gov (United States)

Zand, Pouria; Dilo, Arta; Havinga, Paul

2013-06-27

Current wireless technologies for industrial applications, such as WirelessHART and ISA100.11a, use a centralized management approach where a central network manager handles the requirements of the static network. However, such a centralized approach has several drawbacks. For example, it cannot cope with dynamicity/disturbance in large-scale networks in a real-time manner and it incurs a high communication overhead and latency for exchanging management traffic. In this paper, we therefore propose a distributed network management scheme, D-MSR. It enables the network devices to join the network, schedule their communications, establish end-to-end connections by reserving the communication resources for addressing real-time requirements, and cope with network dynamicity (e.g., node/edge failures) in a distributed manner. According to our knowledge, this is the first distributed management scheme based on IEEE 802.15.4e standard, which guides the nodes in different phases from joining until publishing their sensor data in the network. We demonstrate via simulation that D-MSR can address real-time and reliable communication as well as the high throughput requirements of industrial automation wireless networks, while also achieving higher efficiency in network management than WirelessHART, in terms of delay and overhead.

Real Time Text Analysis

Science.gov (United States)

Senthilkumar, K.; Ruchika Mehra Vijayan, E.

2017-11-01

This paper aims to illustrate real time analysis of large scale data. For practical implementation we are performing sentiment analysis on live Twitter feeds for each individual tweet. To analyze sentiments we will train our data model on sentiWordNet, a polarity assigned wordNet sample by Princeton University. Our main objective will be to efficiency analyze large scale data on the fly using distributed computation. Apache Spark and Apache Hadoop eco system is used as distributed computation platform with Java as development language

Formal methods and tools for the development of distributed and real time systems : Esprit Project 3096 (SPEC)

NARCIS (Netherlands)

Roever, de W.P.; Barringer, H.; Courcoubetis, C.; Gabbay, D.M.; Gerth, R.T.; Jonsson, B.; Pnueli, A.; Reed, M.; Sifakis, J.; Vytopil, J.; Wolper, P.

1990-01-01

The Basic Research Action No. 3096, Formal Methods snd Tools for the Development of Distributed and Real Time Systems, is funded in the Area of Computer Science, under the ESPRIT Programme of the European Community. The coordinating institution is the Department of Computing Science, Eindhoven

Real-Time Multifault Rush Repairing Strategy Based on Utility Theory and Multiagent System in Distribution Networks

Directory of Open Access Journals (Sweden)

Zhao Hao

2016-01-01

Full Text Available The problem of multifault rush repair in distribution networks (DNs is a multiobjective dynamic combinatorial problem with topology constraints. The problem consists of archiving an optimal faults’ allocation strategy to squads and an admissible multifault rush repairing strategy with coordinating switch operations. In this article, the utility theory is introduced to solve the first problem and a new discrete bacterial colony chemotaxis (DBCC algorithm is proposed for the second problem to determine the optimal sequence for each squad to repair faults and the corresponding switch operations. The above solution is called the two-stage approach. Additionally, a double mathematical optimization model based on the fault level is proposed in the second stage to minimize the outage loss and total repairing time. The real-time adjustment multiagent system (RA-MAS is proposed to provide facility to achieve online multifault rush repairing strategy in DNs when there are emergencies after natural disasters. The two-stage approach is illustrated with an example from a real urban distribution network and the simulation results show the effectiveness of the two-stage approach.

Migrating to a real-time distributed parallel simulator architecture

CSIR Research Space (South Africa)

Duvenhage, B

2007-07-01

Full Text Available A legacy non-distributed logical time simulator is migrated to a distributed architecture to parallelise execution. The existing Discrete Time System Specification (DTSS) modelling formalism is retained to simplify the reuse of existing models...

Analysis of serum adenosine deaminase (ADA) and ADA1 and ADA2 isoenzyme activities in HIV positive and HIV-HBV co-infected patients.

Science.gov (United States)

Khodadadi, Iraj; Abdi, Mohammad; Ahmadi, Abbas; Wahedi, Mohammad Saleh; Menbari, Shahoo; Lahoorpour, Fariba; Rahbari, Rezgar

2011-08-01

To determine adenosine deaminase (ADA) activity as a possible diagnostic marker in HIV and HIV-HBV co-infected patients. Blood samples were collected from 72 healthy, 33 HIV positive and 30 HIV-HBV co-infected subjects. Blood CD4+ cell count was recorded and serum alanine aminotransferase, aspartate aminotransferase, alkaline phosphatase, total ADA, and ADA1 and ADA2 isoenzyme activities were determined. Serum ALT, AST, total ADA and ADA2 isoenzyme activities were significantly higher in HIV positive and HIV-HBV co-infected groups compare to the control (pADA activities (R(2)=0.589, pADA was significantly increased in HIV and HIV-HBV co-infections. Therefore, because of its low cost and simplicity to perform, ADA activity might be considered as a useful diagnostic tool among the other markers in these diseases. Copyright © 2011 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Prototyping Real-Time Control in the SPS

CERN Document Server

Andersson, J; Jensen, L; Jones, R; Lamont, M; Wenninger, J; Wijnands, Thijs; CERN. Geneva. AB Department

2003-01-01

Real-time control of beam related parameters will be required in the LHC. In order to gain experience of the issues involved in implementing distributed real-time control over large distances, a prototype local orbit feedback system is being developed in the SPS. This will use 6 pickups, each equipped with the full LHC acquisition electronics chain and linked to a real-time communication and feedback system. This reports summarises the .rst tests performed with this system in October 2002, where the data from four pickups was successfully acquired and displayed at 10 Hz in the control room.

Real-time laser holographic interferometry for aerodynamics

International Nuclear Information System (INIS)

Lee, G.

1987-01-01

Recent developments in thermoplastic recording holograms and advancements in automated image digitalization and analysis make real-time laser holographic interferometry feasible for two-dimensional flows such as airfoil flows. Typical airfoil measurements would include airfoil pressure distributions, wake and boundary layer profiles, and flow field density contours. This paper addresses some of the problems and requirements of a real-time laser holographic interferometer. 13 references

The Katydid system for compiling KEE applications to Ada

Science.gov (United States)

Filman, Robert E.; Bock, Conrad; Feldman, Roy

1990-01-01

Components of a system known as Katydid are developed in an effort to compile knowledge-based systems developed in a multimechanism integrated environment (KEE) to Ada. The Katydid core is an Ada library supporting KEE object functionality, and the other elements include a rule compiler, a LISP-to-Ada translator, and a knowledge-base dumper. Katydid employs translation mechanisms that convert LISP knowledge structures and rules to Ada and utilizes basic prototypes of a run-time KEE object-structure library module for Ada. Preliminary results include the semiautomatic compilation of portions of a simple expert system to run in an Ada environment with the described algorithms. It is suggested that Ada can be employed for AI programming and implementation, and the Katydid system is being developed to include concurrency and synchronization mechanisms.

Optimized Scheduling of Smart Meter Data Access for Real-time Voltage Quality Monitoring

DEFF Research Database (Denmark)

Kemal, Mohammed Seifu; Olsen, Rasmus Løvenstein; Schwefel, Hans-Peter

2018-01-01

Abstract—Active low-voltage distribution grids that support high integration of distributed generation such as photovoltaics and wind turbines require real-time voltage monitoring. At the same time, countries in Europe such as Denmark have close to 100% rollout of smart metering infrastructure....... The metering infrastructure has limitations to provide real-time measurements with small-time granularity. This paper presents an algorithm for optimized scheduling of smart meter data access to provide real-time voltage quality monitoring. The algorithm is analyzed using a real distribution grid in Denmark...

On the Designing of Model Checkers for Real-Time Distributed Systems

Directory of Open Access Journals (Sweden)

D. Yu. Volkanov

2012-01-01

Full Text Available To verify real-time properties of UML statecharts one may apply a UPPAAL, toolbox for model checking of real-time systems. One of the most suitable ways to specify an operational semantics of UML statecharts is to invoke the formal model of Hierarchical Timed Automata. Since the model language of UPPAAL is based on Networks of Timed Automata one has to provide a conversion of Hierarchical Timed Automata to Networks of Timed Automata. In this paper we describe this conversion algorithm and prove that it is correct w.r.t. UPPAAL query language which is based on the subset of Timed CTL.

Distributed real time data processing architecture for the TJ-II data acquisition system

International Nuclear Information System (INIS)

Ruiz, M.; Barrera, E.; Lopez, S.; Machon, D.; Vega, J.; Sanchez, E.

2004-01-01

This article describes the performance of a new model of architecture that has been developed for the TJ-II data acquisition system in order to increase its real time data processing capabilities. The current model consists of several compact PCI extension for instrumentation (PXI) standard chassis, each one with various digitizers. In this architecture, the data processing capability is restricted to the PXI controller's own performance. The controller must share its CPU resources between the data processing and the data acquisition tasks. In the new model, distributed data processing architecture has been developed. The solution adds one or more processing cards to each PXI chassis. This way it is possible to plan how to distribute the data processing of all acquired signals among the processing cards and the available resources of the PXI controller. This model allows scalability of the system. More or less processing cards can be added based on the requirements of the system. The processing algorithms are implemented in LabVIEW (from National Instruments), providing efficiency and time-saving application development when compared with other efficient solutions

Making real-time reactive systems reliable

Science.gov (United States)

Marzullo, Keith; Wood, Mark

1990-01-01

A reactive system is characterized by a control program that interacts with an environment (or controlled program). The control program monitors the environment and reacts to significant events by sending commands to the environment. This structure is quite general. Not only are most embedded real time systems reactive systems, but so are monitoring and debugging systems and distributed application management systems. Since reactive systems are usually long running and may control physical equipment, fault tolerance is vital. The research tries to understand the principal issues of fault tolerance in real time reactive systems and to build tools that allow a programmer to design reliable, real time reactive systems. In order to make real time reactive systems reliable, several issues must be addressed: (1) How can a control program be built to tolerate failures of sensors and actuators. To achieve this, a methodology was developed for transforming a control program that references physical value into one that tolerates sensors that can fail and can return inaccurate values; (2) How can the real time reactive system be built to tolerate failures of the control program. Towards this goal, whether the techniques presented can be extended to real time reactive systems is investigated; and (3) How can the environment be specified in a way that is useful for writing a control program. Towards this goal, whether a system with real time constraints can be expressed as an equivalent system without such constraints is also investigated.

Real-time UNIX in HEP data acquisition

International Nuclear Information System (INIS)

Buono, S.; Gaponenko, I.; Jones, R.; Mapelli, L.; Mornacchi, G.; Prigent, D.; Sanchez-Corral, E.; Skiadelli, M.; Toppers, A.; Duval, P.Y.; Ferrato, D.; Le Van Suu, A.; Qian, Z.; Rondot, C.; Ambrosini, G.; Fumagalli, G.; Aguer, M.; Huet, M.

1994-01-01

Today's experimentation in high energy physics is characterized by an increasing need for sensitivity to rare phenomena and complex physics signatures, which require the use of huge and sophisticated detectors and consequently a high performance readout and data acquisition. Multi-level triggering, hierarchical data collection and an always increasing amount of processing power, distributed throughout the data acquisition layers, will impose a number of features on the software environment, especially the need for a high level of standardization. Real-time UNIX seems, today, the best solution for the platform independence, operating system interface standards and real-time features necessary for data acquisition in HEP experiments. We present the results of the evaluation, in a realistic application environment, of a Real-Time UNIX operating system: the EP/LX real-time UNIX system. ((orig.))

Evaluation of NASA GEOS-ADAS Modeled Diurnal Warming Through Comparisons to SEVIRI and AMSR2 SST Observations

Science.gov (United States)

Gentemann, C. L.; Akella, S.

2018-02-01

An analysis of the ocean skin Sea Surface Temperature (SST) has been included in the Goddard Earth Observing System (GEOS) - Atmospheric Data Assimilation System (ADAS), Version 5 (GEOS-ADAS). This analysis is based on the GEOS atmospheric general circulation model (AGCM) that simulates near-surface diurnal warming and cool skin effects. Analysis for the skin SST is performed along with the atmospheric state, including Advanced Very High Resolution Radiometer (AVHRR) satellite radiance observations as part of the data assimilation system. One month (September, 2015) of GEOS-ADAS SSTs were compared to collocated satellite Spinning Enhanced Visible and InfraRed Imager (SEVIRI) and Advanced Microwave Scanning Radiometer 2 (AMSR2) SSTs to examine how the GEOS-ADAS diurnal warming compares to the satellite measured warming. The spatial distribution of warming compares well to the satellite observed distributions. Specific diurnal events are analyzed to examine variability within a single day. The dependence of diurnal warming on wind speed, time of day, and daily average insolation is also examined. Overall the magnitude of GEOS-ADAS warming is similar to the warming inferred from satellite retrievals, but several weaknesses in the GEOS-AGCM simulated diurnal warming are identified and directly related back to specific features in the formulation of the diurnal warming model.

ADA5/SPT20 links the ADA and SPT genes, which are involved in yeast transcription.

OpenAIRE

Marcus, G A; Horiuchi, J; Silverman, N; Guarente, L

1996-01-01

In this report we described the cloning and characterization of ADA5, a gene identified by resistance to GAL4-VP16-mediated toxicity. ADA5 binds directly to the VP16 activation domain but not to a transcriptionally defective VP16 double point mutant. Double mutants with mutations in ada5 and other genes (ada2 or ada3) isolated by resistance to GAL4-VP16 grow like ada5 single mutants, suggesting that ADA5 is in the same pathway as the other ADA genes. Further, ADA5 cofractionates and coprecipi...

Analysis and Synthesis of Distributed Real-Time Embedded Systems

DEFF Research Database (Denmark)

Pop, Paul; Eles, Petru; Peng, Zebo

like automotive electronics, real-time multimedia, avionics, medical equipment, and factory systems. The proposed analysis and synthesis techniques derive optimized implementations that fulfill the imposed design constraints. An important part of the implementation process is the synthesis...

Distributed energy resources scheduling considering real-time resources forecast

DEFF Research Database (Denmark)

Silva, M.; Sousa, T.; Ramos, S.

2014-01-01

grids and considering day-ahead, hour-ahead and realtime time horizons. This method considers that energy resources are managed by a VPP which establishes contracts with their owners. The full AC power flow calculation included in the model takes into account network constraints. In this paper......, distribution function errors are used to simulate variations between time horizons, and to measure the performance of the proposed methodology. A 33-bus distribution network with large number of distributed resources is used....

Ada Dual-Use Summary: Ada Dual-Use Workshop Held in Vienna, Virginia on October 19-20, 1993. Ada Dual-Use Committee Briefing, November 8, 1993

Science.gov (United States)

1993-11-29

Systems Agency C- 19 Novemtiber 8., 1993 Promoting the Use of Ada in Computer Science Curricula Timothy J. Long Ohio State University ®I To L4 ease...framework, distributed file systems, a high-performance fiber-optic connection and multi-processor modules to work with the OSF’s Mach 3 microkernel (again

Multiprocessor performance modeling with ADAS

Science.gov (United States)

Hayes, Paul J.; Andrews, Asa M.

1989-01-01

A graph managing strategy referred to as the Algorithm to Architecture Mapping Model (ATAMM) appears useful for the time-optimized execution of application algorithm graphs in embedded multiprocessors and for the performance prediction of graph designs. This paper reports the modeling of ATAMM in the Architecture Design and Assessment System (ADAS) to make an independent verification of ATAMM's performance prediction capability and to provide a user framework for the evaluation of arbitrary algorithm graphs. Following an overview of ATAMM and its major functional rules are descriptions of the ADAS model of ATAMM, methods to enter an arbitrary graph into the model, and techniques to analyze the simulation results. The performance of a 7-node graph example is evaluated using the ADAS model and verifies the ATAMM concept by substantiating previously published performance results.

Ada Compiler Validation Summary Report: Certificate Number 890711W1. 10109 Concurrent Computer Corporation C(3) Ada, Version R02-02.00 Concurrent Computer Corporation 3280 MPS

Science.gov (United States)

1989-07-11

Wright-Patterson ATB Dayton, OH, USA Ada Joint Prograr Office United States De artment of Defense " * ’ , Washington, DC 2 301-3061 i4. I 10 k A$ -h-Y...dependent but is permitted by the Ada Standard. Six classes of tests are used. These tests are designed to perform checks at compile time, at link time...the direction of the AVF according to procedures establizhed by the Ada Joia ,, Program Office and administered by the Ada Validation Organization (AVO

Scheduling and Communication Synthesis for Distributed Real-Time Systems

DEFF Research Database (Denmark)

Pop, Paul

2000-01-01

on aspects of scheduling and communication for embedded real-time systems. Special emphasis has been placed on the impact of the communication infrastructure and protocol on the overall system performance. The scheduling and communication strategies proposed are based on an abstract graph representation...

Distributed Coordination of Electric Vehicle Charging in a Community Microgrid Considering Real-Time Price

DEFF Research Database (Denmark)

Li, Chendan; Schaltz, Erik; Quintero, Juan Carlos Vasquez

2016-01-01

The predictable increasing adoption of EV by residential users imposes the necessity of Electric Vehicle charging coordination, in order to charge effectively while minimizing the impact on the grid. In this paper, a two-stage distributed coordination algorithm for electric vehicle charging...... management in a community microgrid is proposed. Each local EV charging controller is taken as an agent, which can manage the charging to achieve the optimization of the whole community by communicating in a sparse network. The proposed algorithm aims at optimizing real-time, which manages the charging...

ART-Ada design project, phase 2

Science.gov (United States)

Lee, S. Daniel; Allen, Bradley P.

1990-01-01

Interest in deploying expert systems in Ada has increased. An Ada based expert system tool is described called ART-Ada, which was built to support research into the language and methodological issues of expert systems in Ada. ART-Ada allows applications of an existing expert system tool called ART-IM (Automated Reasoning Tool for Information Management) to be deployed in various Ada environments. ART-IM, a C-based expert system tool, is used to generate Ada source code which is compiled and linked with an Ada based inference engine to produce an Ada executable image. ART-Ada is being used to implement several expert systems for NASA's Space Station Freedom Program and the U.S. Air Force.

Modern Energy Markets Real-Time Pricing, Renewable Resources and Efficient Distribution

CERN Document Server

Kopsakangas-Savolainen, Maria

2012-01-01

Energy has moved to the forefront in terms of societal and economic development. Modern Energy Markets is a comprehensive, economically oriented, exploration of modern electricity networks from production and distribution to deregulation and liberalization processes. Updating previous work by the authors, different aspects are considered resulting in a complete and detailed picture of  the systems and characteristics of modern electricity markets. Modern Energy Markets provides clear detail whilst encompassing a broad scope of topics and includes: •A method to model energy production systems including the main characteristics of future demand side management, •Different applications of this model in nuclear and renewable energy scenarios, •An analysis of Real-Time Pricing of electricity and its potential effects across the market, and, •A discussion of the need for regulation in an easily monopolized industry. Engineering and Economics students alike will find that Modern Energy Markets is a succinct...

El espíritu del lugar en las Cañadas Reales de la Corona de Castilla./The spirit of the place in Canadas Royal Crown of Castile.

Directory of Open Access Journals (Sweden)

Cahn, Alicia Leonor

2008-12-01

Full Text Available El sistema de las Cañadas Reales y sus vías accesorias constituye un conjunto dinámico de gran trascendencia económica e histórica ─con 600 años de historia─ en el que se vinculan entre sí, dentro de un proceso productivo hábilmente organizado y dirigido a una finalidad concreta de índole comercial, los trazados viales de diferentes épocas, cada uno con sus testimonios particulares en cuanto a modos de hacer, tecnologías y materiales, en un amplio territorio interior./The Cañadas Reales system and accessory pathways is a dynamic set of great importance to economic and historical ─ 600 years of history ─ in which they are linked together within a production process skillfully organized and led for a particular purpose in nature commercial road paths from different eras, each with its particular testimony as to ways of doing things, technologies and materials in a wide hinterland.

An Evaluation of an Ada Implementation of the Rete Algorithm for Embedded Flight Processors

Science.gov (United States)

1990-12-01

computers was desired. The VAX VMS operating system has many built-in methods for determining program performance (including VAX PCA), but these methods... overviev , of the target environment-- the MIL-STD-1750A VHSIC Avionic Modular Processor ( VA.IP, running under the Ada Avionics Real-Time Software (AARTS... computers . Mil-STD-1750A, the Air Force’s standard flight computer architecture, however, places severe constraints on applications software processing

Time synchronization for an Ethernet-based real-time token network

NARCIS (Netherlands)

Hanssen, F.T.Y.; van den Boom, Joost; Jansen, P.G.; Scholten, Johan

We present a distributed clock synchronization algorithm. It performs clock synchronization on an Ethernet-based real-time token local area network, without the use of an external clock source. It is used to enable the token schedulers in each node to agree upon a common time. Its intended use is in

Ada To X-Window Bindings

Science.gov (United States)

Souleles, Dean

1993-01-01

Ada to X-Window Bindings computer program developed to provide Ada programmers with complete interfaces to Xt Intrinsics and OSF Motif toolkits. Provides "Ada view" of some mostly C-language programming libraries. Package of software written in Ada and C languages.

Real-time qualitative study of forsterite crystal - Melt lithium distribution by laser-induced breakdown spectroscopy

Science.gov (United States)

Lebedev, V. F.; Makarchuk, P. S.; Stepanov, D. N.

2017-11-01

A factor of lithium distribution between single-crystal forsterite (Cr,Li:Mg2SiO4) and its melt are studied by laser-induced breakdown spectroscopy. Lithium content in the crystalline phase is found to achieve a saturation at relatively low Li concentration in the melt (about 0.02%wt.). An algorithm and software are developed for real-time analysis of the studied spectra of lithium trace amounts at wide variation of the plasma radiation intensity. The analyzed plasma spectra processing method is based on the calculation of lithium emission part in the total emission of the target plasma for each recorded spectrum followed by the error estimation for the series of measurements in the normal distribution approximation.

A reliable information management for real-time systems

International Nuclear Information System (INIS)

Nishihara, Takuo; Tomita, Seiji

1995-01-01

In this paper, we propose a system configuration suitable for the hard realtime systems in which integrity and durability of information are important. On most hard real-time systems, where response time constraints are critical, the data which program access are volatile, and may be lost in case the systems are down. But for some real-time systems, the value-added intelligent network (IN) systems, e.g., integrity and durability of the stored data are very important. We propose a distributed system configuration for such hard real-time systems, comprised of service control modules and data management modules. The service control modules process transactions and responses based on deadline control, and the data management modules deal the stored data based on information recovery schemes well-restablished in fault real-time systems. (author)

Real Time Revisited

Science.gov (United States)

Allen, Phillip G.

1985-12-01

The call for abolishing photo reconnaissance in favor of real time is once more being heard. Ten years ago the same cries were being heard with the introduction of the Charge Coupled Device (CCD). The real time system problems that existed then and stopped real time proliferation have not been solved. The lack of an organized program by either DoD or industry has hampered any efforts to solve the problems, and as such, very little has happened in real time in the last ten years. Real time is not a replacement for photo, just as photo is not a replacement for infra-red or radar. Operational real time sensors can be designed only after their role has been defined and improvements made to the weak links in the system. Plodding ahead on a real time reconnaissance suite without benefit of evaluation of utility will allow this same paper to be used ten years from now.

Automatic data-driven real-time segmentation and recognition of surgical workflow.

Science.gov (United States)

Dergachyova, Olga; Bouget, David; Huaulmé, Arnaud; Morandi, Xavier; Jannin, Pierre

2016-06-01

With the intention of extending the perception and action of surgical staff inside the operating room, the medical community has expressed a growing interest towards context-aware systems. Requiring an accurate identification of the surgical workflow, such systems make use of data from a diverse set of available sensors. In this paper, we propose a fully data-driven and real-time method for segmentation and recognition of surgical phases using a combination of video data and instrument usage signals, exploiting no prior knowledge. We also introduce new validation metrics for assessment of workflow detection. The segmentation and recognition are based on a four-stage process. Firstly, during the learning time, a Surgical Process Model is automatically constructed from data annotations to guide the following process. Secondly, data samples are described using a combination of low-level visual cues and instrument information. Then, in the third stage, these descriptions are employed to train a set of AdaBoost classifiers capable of distinguishing one surgical phase from others. Finally, AdaBoost responses are used as input to a Hidden semi-Markov Model in order to obtain a final decision. On the MICCAI EndoVis challenge laparoscopic dataset we achieved a precision and a recall of 91 % in classification of 7 phases. Compared to the analysis based on one data type only, a combination of visual features and instrument signals allows better segmentation, reduction of the detection delay and discovery of the correct phase order.

Statistical quality analysis of schedulers under soft-real-time constraints

NARCIS (Netherlands)

Baarsma, H.E.; Hurink, Johann L.; Jansen, P.G.

2007-01-01

This paper describes an algorithm to determine the performance of real-time systems with tasks using stochastic processing times. Such an algorithm can be used for guaranteeing Quality of Service of periodic tasks with soft real-time constraints. We use a discrete distribution model of processing

Development of a High Resolution, Real Time, Distribution-Level Metering System and Associated Visualization, Modeling, and Data Analysis Functions

Energy Technology Data Exchange (ETDEWEB)

Bank, J.; Hambrick, J.

2013-05-01

NREL is developing measurement devices and a supporting data collection network specifically targeted at electrical distribution systems to support research in this area. This paper describes the measurement network which is designed to apply real-time and high speed (sub-second) measurement principles to distribution systems that are already common for the transmission level in the form of phasor measurement units and related technologies.

Compiling knowledge-based systems from KEE to Ada

Science.gov (United States)

Filman, Robert E.; Bock, Conrad; Feldman, Roy

1990-01-01

The dominant technology for developing AI applications is to work in a multi-mechanism, integrated, knowledge-based system (KBS) development environment. Unfortunately, systems developed in such environments are inappropriate for delivering many applications - most importantly, they carry the baggage of the entire Lisp environment and are not written in conventional languages. One resolution of this problem would be to compile applications from complex environments to conventional languages. Here the first efforts to develop a system for compiling KBS developed in KEE to Ada (trademark). This system is called KATYDID, for KEE/Ada Translation Yields Development Into Delivery. KATYDID includes early prototypes of a run-time KEE core (object-structure) library module for Ada, and translation mechanisms for knowledge structures, rules, and Lisp code to Ada. Using these tools, part of a simple expert system was compiled (not quite automatically) to run in a purely Ada environment. This experience has given us various insights on Ada as an artificial intelligence programming language, potential solutions of some of the engineering difficulties encountered in early work, and inspiration on future system development.

A distributed real-time Java system based on CSP

NARCIS (Netherlands)

Bakkers, André; Hilderink, G.H.; Broenink, Johannes F.

1999-01-01

Real-time embedded systems in general require a reliability that is orders of magnitude higher than what is presently obtainable with state of the art C programs. The reason for the poor reliability of present day software is the unavailability of a formalism to design sequential C programs. The use

Criticality: static profiling for real-time programs

DEFF Research Database (Denmark)

Brandner, Florian; Hepp, Stefan; Jordan, Alexander

2014-01-01

With the increasing performance demand in real-time systems it becomes more and more important to provide feedback to programmers and software development tools on the performance-relevant code parts of a real-time program. So far, this information was limited to an estimation of the worst....... Experiments using well-established real-time benchmark programs show an interesting distribution of the criticality values, revealing considerable amounts of highly critical as well as uncritical code. The metric thus provides ideal information to programmers and software development tools to optimize...... view covering the entire code base, tools in the spirit of program profiling are required. This work proposes an efficient approach to compute worst-case timing information for all code parts of a program using a complementary metric, called criticality. Every statement of a program is assigned...

Nanoimprinted distributed feedback dye laser sensor for real-time imaging of small molecule diffusion

DEFF Research Database (Denmark)

Vannahme, Christoph; Dufva, Martin; Kristensen, Anders

2014-01-01

Label-free imaging is a promising tool for the study of biological processes such as cell adhesion and small molecule signaling processes. In order to image in two dimensions of space current solutions require motorized stages which results in low imaging frame rates. Here, a highly sensitive...... distributed feedback (DFB) dye laser sensor for real-time label-free imaging without any moving parts enabling a frame rate of 12 Hz is presented. The presence of molecules on the laser surface results in a wavelength shift which is used as sensor signal. The unique DFB laser structure comprises several areas...

Replacing OSE with Real Time capable Linux

OpenAIRE

Boman, Simon; Rutgersson, Olof

2009-01-01

For many years OSE has been a common used operating system, with real time extensions enhancements, in embed-ded systems. But in the last decades, Linux has grown and became a competitor to common operating systems and, in recent years, even as an operating system with real time extensions. With this in mind, ÅF was interested in replacing the quite expensive OSE with some distribution of the open source based Linux on a PowerPC MPC8360. Therefore, our purpose with thesis is to implement Linu...

Survey of real-time processing systems for big data

DEFF Research Database (Denmark)

Liu, Xiufeng; Lftikhar, Nadeem; Xie, Xike

2014-01-01

In recent years, real-time processing and analytics systems for big data–in the context of Business Intelligence (BI)–have received a growing attention. The traditional BI platforms that perform regular updates on daily, weekly or monthly basis are no longer adequate to satisfy the fast......-changing business environments. However, due to the nature of big data, it has become a challenge to achieve the real-time capability using the traditional technologies. The recent distributed computing technology, MapReduce, provides off-the-shelf high scalability that can significantly shorten the processing time...... for big data; Its open-source implementation such as Hadoop has become the de-facto standard for processing big data, however, Hadoop has the limitation of supporting real-time updates. The improvements in Hadoop for the real-time capability, and the other alternative real-time frameworks have been...

Distribution Locational Real-Time Pricing Based Smart Building Control and Management

Energy Technology Data Exchange (ETDEWEB)

Hao, Jun; Dai, Xiaoxiao; Zhang, Yingchen; Zhang, Jun; Gao, Wenzhong

2016-11-21

This paper proposes an real-virtual parallel computing scheme for smart building operations aiming at augmenting overall social welfare. The University of Denver's campus power grid and Ritchie fitness center is used for demonstrating the proposed approach. An artificial virtual system is built in parallel to the real physical system to evaluate the overall social cost of the building operation based on the social science based working productivity model, numerical experiment based building energy consumption model and the power system based real-time pricing mechanism. Through interactive feedback exchanged between the real and virtual system, enlarged social welfare, including monetary cost reduction and energy saving, as well as working productivity improvements, can be achieved.

Validation and Assessment of Multi-GNSS Real-Time Precise Point Positioning in Simulated Kinematic Mode Using IGS Real-Time Service

Directory of Open Access Journals (Sweden)

Liang Wang

2018-02-01

Full Text Available Precise Point Positioning (PPP is a popular technology for precise applications based on the Global Navigation Satellite System (GNSS. Multi-GNSS combined PPP has become a hot topic in recent years with the development of multiple GNSSs. Meanwhile, with the operation of the real-time service (RTS of the International GNSS Service (IGS agency that provides satellite orbit and clock corrections to broadcast ephemeris, it is possible to obtain the real-time precise products of satellite orbits and clocks and to conduct real-time PPP. In this contribution, the real-time multi-GNSS orbit and clock corrections of the CLK93 product are applied for real-time multi-GNSS PPP processing, and its orbit and clock qualities are investigated, first with a seven-day experiment by comparing them with the final multi-GNSS precise product ‘GBM’ from GFZ. Then, an experiment involving real-time PPP processing for three stations in the Multi-GNSS Experiment (MGEX network with a testing period of two weeks is conducted in order to evaluate the convergence performance of real-time PPP in a simulated kinematic mode. The experimental result shows that real-time PPP can achieve a convergence performance of less than 15 min for an accuracy level of 20 cm. Finally, the real-time data streams from 12 globally distributed IGS/MGEX stations for one month are used to assess and validate the positioning accuracy of real-time multi-GNSS PPP. The results show that the simulated kinematic positioning accuracy achieved by real-time PPP on different stations is about 3.0 to 4.0 cm for the horizontal direction and 5.0 to 7.0 cm for the three-dimensional (3D direction.

The testability of Ada programs

Science.gov (United States)

Auty, David; Cohen, Norman H.

1986-01-01

Software development for NASA's Space Station poses a significant problem; considered the most difficult by some. The difficulty is the magnitude and complexity of the required software. The concerns raised by consideration of the requirements for testing and checkout procedures for the Space Station software are addressed. In particular, it addresses the use of Ada in the development of widely distributed yet closely coordinated processing.

Ada in AI or AI in Ada. On developing a rationale for integration

Science.gov (United States)

Collard, Philippe E.; Goforth, Andre

1988-01-01

The use of Ada as an Artificial Intelligence (AI) language is gaining interest in the NASA Community, i.e., by parties who have a need to deploy Knowledge Based-Systems (KBS) compatible with the use of Ada as the software standard for the Space Station. A fair number of KBS and pseudo-KBS implementations in Ada exist today. Currently, no widely used guidelines exist to compare and evaluate these with one another. The lack of guidelines illustrates a fundamental problem inherent in trying to compare and evaluate implementations of any sort in languages that are procedural or imperative in style, such as Ada, with those in languages that are functional in style, such as Lisp. Discussed are the strengths and weakness of using Ada as an AI language and a preliminary analysis provided of factors needed for the development of criteria for the integration of these two families of languages and the environments in which they are implemented. The intent for developing such criteria is to have a logical rationale that may be used to guide the development of Ada tools and methodology to support KBS requirements, and to identify those AI technology components that may most readily and effectively be deployed in Ada.

What is the clinically relevant change on the ADAS-Cog?

Science.gov (United States)

Schrag, Anette; Schott, Jonathan M

2012-02-01

To establish the minimal clinically relevant change (MCRC) on the Alzheimer's Disease Assessment Scale-Cognitive (ADAS-Cog) for patients with mild Alzheimer's disease (AD). Cohort study. 59 recruiting sites for the Alzheimer's Disease Neuroimaging Initiative. Outpatients with AD in the Alzheimer's Disease Neuroimaging Initiative. The authors applied anchor-based MCRC methodology comparing ADAS-Cog change against clinicians' judgement of clinically relevant worsening between baseline and 6 months in four domains: memory and non-memory cognitive performance; Clinical Dementia Rating Scale; and Functional Assessment Questionnaire. The analysis was repeated for the 6-12-month interval. To support these findings, the authors calculated distribution-based measures including half-baseline SD (1/2 SD) and SEM. 181 patients (baseline ADAS-Cog score 18.5±6.4) had ADAS-Cog data at 0 and 6 months. Those undergoing clinically significant worsening on any of the four anchor questions (n=41-47) had an average ADAS-Cog change of 3.1-3.8 points. Similar results were found for the 177 patients with 6-12-month data. The average 1/2 SD for the baseline ADAS-Cog score was 3.2, and the SEM was 3.7. 3 points decline on the ADAS-Cog may be an appropriate MCRC for clinical trials of patients with early AD. However, further studies assessing the MCRC for improvement on the ADAS-Cog, using patient-based judgement as an anchor, and determining the minimal clinically relevant difference between change on two treatments are required. http://clinicalTrials.gov Identifier: NCT00106899.

Cf-252 based neutron radiography using real-time image processing system

International Nuclear Information System (INIS)

Mochiki, Koh-ichi; Koiso, Manabu; Yamaji, Akihiro; Iwata, Hideki; Kihara, Yoshitaka; Sano, Shigeru; Murata, Yutaka

2001-01-01

For compact Cf-252 based neutron radiography, a real-time image processing system by particle counting technique has been developed. The electronic imaging system consists of a supersensitive imaging camera, a real-time corrector, a real-time binary converter, a real-time calculator for centroid, a display monitor and a computer. Three types of accumulated NR image; ordinary, binary and centroid images, can be observed during a measurement. Accumulated NR images were taken by the centroid mode, the binary mode and ordinary mode using of Cf-252 neutron source and those images were compared. The centroid mode presented the sharpest image and its statistical characteristics followed the Poisson distribution, while the ordinary mode showed the smoothest image as the averaging effect by particle bright spots with distributed brightness was most dominant. (author)

Fault tolerant distributed real time computer systems for I and C of prototype fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Manimaran, M., E-mail: maran@igcar.gov.in; Shanmugam, A.; Parimalam, P.; Murali, N.; Satya Murty, S.A.V.

2014-03-15

Highlights: • Architecture of distributed real time computer system (DRTCS) used in I and C of PFBR is explained. • Fault tolerant (hot standby) architecture, fault detection and switch over are detailed. • Scaled down model was used to study functional and performance requirements of DRTCS. • Quality of service parameters for scaled down model was critically studied. - Abstract: Prototype fast breeder reactor (PFBR) is in the advanced stage of construction at Kalpakkam, India. Three-tier architecture is adopted for instrumentation and control (I and C) of PFBR wherein bottom tier consists of real time computer (RTC) systems, middle tier consists of process computers and top tier constitutes of display stations. These RTC systems are geographically distributed and networked together with process computers and display stations. Hot standby architecture comprising of dual redundant RTC systems with switch over logic system is deployed in order to achieve fault tolerance. Fault tolerant dual redundant network connectivity is provided in each RTC system and TCP/IP protocol is selected for network communication. In order to assess the performance of distributed RTC systems, scaled down model was developed with 9 representative systems and nearly 15% of I and C signals of PFBR were connected and monitored. Functional and performance testing were carried out for each RTC system and the fault tolerant characteristics were studied by creating various faults into the system and observed the performance. Various quality of service parameters like connection establishment delay, priority parameter, transit delay, throughput, residual error ratio, etc., are critically studied for the network.

Distributed time management in transputer networks

NARCIS (Netherlands)

Vervoort, Wiek; te West, R.; Schoute, Albert L.; Hofstede, J.

1991-01-01

For real-time applications in a distributed system a common notion of time is indispensable. Clocks are used for time measurement, determination of causality, process synchronization and generating unique identifications. All this is only possible if there is a time reference of specified accuracy.

Overfitting Reduction of Text Classification Based on AdaBELM

Directory of Open Access Journals (Sweden)

Xiaoyue Feng

2017-07-01

Full Text Available Overfitting is an important problem in machine learning. Several algorithms, such as the extreme learning machine (ELM, suffer from this issue when facing high-dimensional sparse data, e.g., in text classification. One common issue is that the extent of overfitting is not well quantified. In this paper, we propose a quantitative measure of overfitting referred to as the rate of overfitting (RO and a novel model, named AdaBELM, to reduce the overfitting. With RO, the overfitting problem can be quantitatively measured and identified. The newly proposed model can achieve high performance on multi-class text classification. To evaluate the generalizability of the new model, we designed experiments based on three datasets, i.e., the 20 Newsgroups, Reuters-21578, and BioMed corpora, which represent balanced, unbalanced, and real application data, respectively. Experiment results demonstrate that AdaBELM can reduce overfitting and outperform classical ELM, decision tree, random forests, and AdaBoost on all three text-classification datasets; for example, it can achieve 62.2% higher accuracy than ELM. Therefore, the proposed model has a good generalizability.

A Unified Framework for Verification and Complexity Analysis of Real-Time and Distributed Systems

National Research Council Canada - National Science Library

Lynch, Nancy

1997-01-01

.... These examples arise from a diverse set of application areas, including connection management protocols, clock synchronization, fault-tolerant distributed consensus, group communication, and real...

State of the art on fault-tolerant real time distributed systems

International Nuclear Information System (INIS)

Levkov, V.

1992-06-01

The integration of new computerized functions in power plant, and especially nuclear power plant, control and instrumentation systems implies more and more stringent requirements as to communication system reliability. For if an item of equipment, or even a computer program, can be validated and qualified, no formal qualification procedure is presently imposed on communication networks. This is certainly due to the relative immaturity of these networks, but also to their complexity. It is for this reason that, in the context of preparation for the future PWR 2000 standardized nuclear plants, it would seem appropriate to take a look at fault-tolerant communication systems. Since C and I type applications (in the control room) are divided between several computers and are required to contend with extremely severe time constraints, EDF has undertaken investigation of fault-tolerant, real time distributed systems. This paper summarized the state of the art in the field as it appears from discussion with computer manufacturers, academics and research workers on related projects. The results obtained were then used to determine trends as to ''promising'' solutions. The paper concludes with recommended study programs for the PCC department of EDF/R and DD for the next few years. (author), 9 figs., 10 refs., 2 annexes

Real time equilibrium reconstruction for tokamak discharge control

International Nuclear Information System (INIS)

Ferron, J.R.; Walker, M.L.; Lao, L.L.; St John, H.E.; Humphreys, D.A.; Leuer, J.A.

1998-01-01

A practical method for performing a tokamak equilibrium reconstruction in real time for arbitrary time varying discharge shapes and current profiles is described. An approximate solution to the Grad-Shafranov equilibrium relation is found which best fits the diagnostic measurements. Thus, a solution for the spatial distribution of poloidal flux and toroidal current density is available in real time that is consistent with plasma force balance, allowing accurate evaluation of parameters such as discharge shape and safety factor profile. The equilibrium solutions are produced at a rate sufficient for discharge control. This equilibrium reconstruction algorithm has been implemented on the digital plasma control system for the DIII-D tokamak. The first application of real time equilibrium reconstruction to discharge shape control is described. (author)

Resource Optimization in Distributed Real-Time Multimedia Applications

NARCIS (Netherlands)

Yang, R.; van der Mei, R.D.; Roubos, D.; Seinstra, F.J.; Bal, H.E.

2012-01-01

The research area of multimedia content analysis (MMCA) considers all aspects of the automated extraction of knowledge from multimedia archives and data streams. To adhere to strict time constraints, large-scalemultimedia applications typically are being executed on distributed systems consisting of

Timeliness and Predictability in Real-Time Database Systems

National Research Council Canada - National Science Library

Son, Sang H

1998-01-01

The confluence of computers, communications, and databases is quickly creating a globally distributed database where many applications require real time access to both temporally accurate and multimedia data...

Real-Time Application Performance Steering and Adaptive Control

National Research Council Canada - National Science Library

Reed, Daniel

2002-01-01

.... The objective of the Real-time Application Performance Steering and Adaptive Control project is to replace ad hoc, post-mortem performance optimization with an extensible, portable, and distributed...

A MATLAB based Distributed Real-time Simulation of Lander-Orbiter-Earth Communication for Lunar Missions

Science.gov (United States)

Choudhury, Diptyajit; Angeloski, Aleksandar; Ziah, Haseeb; Buchholz, Hilmar; Landsman, Andre; Gupta, Amitava; Mitra, Tiyasa

Lunar explorations often involve use of a lunar lander , a rover [1],[2] and an orbiter which rotates around the moon with a fixed radius. The orbiters are usually lunar satellites orbiting along a polar orbit to ensure visibility with respect to the rover and the Earth Station although with varying latency. Communication in such deep space missions is usually done using a specialized protocol like Proximity-1[3]. MATLAB simulation of Proximity-1 have been attempted by some contemporary researchers[4] to simulate all features like transmission control, delay etc. In this paper it is attempted to simulate, in real time, the communication between a tracking station on earth (earth station), a lunar orbiter and a lunar rover using concepts of Distributed Real-time Simulation(DRTS).The objective of the simulation is to simulate, in real-time, the time varying communication delays associated with the communicating elements with a facility to integrate specific simulation modules to study different aspects e.g. response due to a specific control command from the earth station to be executed by the rover. The hardware platform comprises four single board computers operating as stand-alone real time systems (developed by MATLAB xPC target and inter-networked using UDP-IP protocol). A time triggered DRTS approach is adopted. The earth station, the orbiter and the rover are programmed as three standalone real-time processes representing the communicating elements in the system. Communication from one communicating element to another constitutes an event which passes a state message from one element to another, augmenting the state of the latter. These events are handled by an event scheduler which is the fourth real-time process. The event scheduler simulates the delay in space communication taking into consideration the distance between the communicating elements. A unique time synchronization algorithm is developed which takes into account the large latencies in space

Distribution of Isotopic and Environmental Tracers in Groundwater, Northern Ada County, Southwestern Idaho

Science.gov (United States)

Adkins, Candice B.; Bartolino, James R.

2010-01-01

Residents of northern Ada County, Idaho, depend on groundwater for domestic and agricultural uses. The population of this area is growing rapidly and groundwater resources must be understood for future water-resource management. The U.S. Geological Survey, in cooperation with the Idaho Department of Water Resources, used a suite of isotopic and environmental tracers to gain a better understanding of groundwater ages, recharge sources, and flowpaths in northern Ada County. Thirteen wells were sampled between September and October 2009 for field parameters, major anions and cations, nutrients, oxygen and hydrogen isotopes, tritium, radiocarbon, chlorofluorocarbons, and dissolved gasses. Well depths ranged from 30 to 580 feet below land surface. Wells were grouped together based on their depth and geographic location into the following four categories: shallow aquifer, intermediate/deep aquifer, Willow Creek aquifer, and Dry Creek aquifer. Major cations and anions indicated calcium-bicarbonate and sodium-bicarbonate water types in the study area. Oxygen and hydrogen isotopes carried an oxygen-18 excess signature, possibly indicating recharge from evaporated sources or water-rock interactions in the subsurface. Chlorofluorocarbons detected modern (post-1940s) recharge in every well sampled; tritium data indicated modern water (post-1951) in seven, predominantly shallow wells. Nutrient concentrations tended to be greater in wells signaling recent recharge based on groundwater age dating, thus confirming the presence of recent recharge in these wells. Corrected radiocarbon results generated estimated residence times from modern to 5,100 years before present. Residence time tended to increase with depth, as confirmed by all three age-tracers. The disagreement among residence times indicates that samples were well-mixed and that the sampled aquifers contain a mixture of young and old recharge. Due to a lack of data, no conclusions about sources of recharge could be drawn

A curriculum for real-time computer and control systems engineering

Science.gov (United States)

Halang, Wolfgang A.

1990-01-01

An outline of a syllabus for the education of real-time-systems engineers is given. This comprises the treatment of basic concepts, real-time software engineering, and programming in high-level real-time languages, real-time operating systems with special emphasis on such topics as task scheduling, hardware architectures, and especially distributed automation structures, process interfacing, system reliability and fault-tolerance, and integrated project development support systems. Accompanying course material and laboratory work are outlined, and suggestions for establishing a laboratory with advanced, but low-cost, hardware and software are provided. How the curriculum can be extended into a second semester is discussed, and areas for possible graduate research are listed. The suitable selection of a high-level real-time language and supporting operating system for teaching purposes is considered.

Reducing lumber thickness variation using real-time statistical process control

Science.gov (United States)

Thomas M. Young; Brian H. Bond; Jan Wiedenbeck

2002-01-01

A technology feasibility study for reducing lumber thickness variation was conducted from April 2001 until March 2002 at two sawmills located in the southern U.S. A real-time statistical process control (SPC) system was developed that featured Wonderware human machine interface technology (HMI) with distributed real-time control charts for all sawing centers and...

Adding Timing Requirements to the CODARTS Real-Time Software Design Method

DEFF Research Database (Denmark)

Bach, K.R.

The CODARTS software design method consideres how concurrent, distributed and real-time applications can be designed. Although accounting for the important issues of task and communication, the method does not provide means for expressing the timeliness of the tasks and communication directly...

Full integrated system of real-time monitoring based on distributed architecture for the high temperature engineering test reactor (HTTR)

International Nuclear Information System (INIS)

Subekti, Muhammad; Ohno, Tomio; Kudo, Kazuhiko; Takamatsu, Kuniyoshi; Nabeshima, Kunihiko

2005-01-01

A new monitoring system scheme based on distributed architecture for the High Temperature Engineering Test Reactor (HTTR) is proposed to assure consistency of the real-time process of expanded system. A distributed monitoring task on client PCs as an alternative architecture maximizes the throughput and capabilities of the system even if the monitoring tasks suffer a shortage of bandwidth. The prototype of the on-line monitoring system has been developed successfully and will be tested at the actual HTTR site. (author)

Item analysis of ADAS-Cog: effect of baseline cognitive impairment in a clinical AD trial.

Science.gov (United States)

Sevigny, Jeffrey J; Peng, Yahong; Liu, Lian; Lines, Christopher R

2010-03-01

We explored the association of Alzheimer's disease (AD) Assessment Scale (ADAS-Cog) item scores with AD severity using cross-sectional and longitudinal data from the same study. Post hoc analyses were performed using placebo data from a 12-month trial of patients with mild-to-moderate AD (N =281 randomized, N =209 completed). Baseline distributions of ADAS-Cog item scores by Mini-Mental State Examination (MMSE) score and Clinical Dementia Rating (CDR) sum of boxes score (measures of dementia severity) were estimated using local and nonparametric regressions. Mixed-effect models were used to characterize ADAS-Cog item score changes over time by dementia severity (MMSE: mild =21-26, moderate =14-20; global CDR: mild =0.5-1, moderate =2). In the cross-sectional analysis of baseline ADAS-Cog item scores, orientation was the most sensitive item to differentiate patients across levels of cognitive impairment. Several items showed a ceiling effect, particularly in milder AD. In the longitudinal analysis of change scores over 12 months, orientation was the only item with noticeable decline (8%-10%) in mild AD. Most items showed modest declines (5%-20%) in moderate AD.

Real-Time Support on IEEE 802.11 Wireless Ad-Hoc Networks: Reality vs. Theory

Science.gov (United States)

Kang, Mikyung; Kang, Dong-In; Suh, Jinwoo

The usable throughput of an IEEE 802.11 system for an application is much less than the raw bandwidth. Although 802.11b has a theoretical maximum of 11Mbps, more than half of the bandwidth is consumed by overhead leaving at most 5Mbps of usable bandwidth. Considering this characteristic, this paper proposes and analyzes a real-time distributed scheduling scheme based on the existing IEEE 802.11 wireless ad-hoc networks, using USC/ISI's Power Aware Sensing Tracking and Analysis (PASTA) hardware platform. We compared the distributed real-time scheduling scheme with the real-time polling scheme to meet deadline, and compared a measured real bandwidth with a theoretical result. The theoretical and experimental results show that the distributed scheduling scheme can guarantee real-time traffic and enhances the performance up to 74% compared with polling scheme.

Gender-specific association of ADA genetic polymorphism with human longevity.

Science.gov (United States)

Napolioni, Valerio; Lucarini, Nazzareno

2010-08-01

Aim of this study was to investigate whether the polymorphic ADA (Adenosine Deaminase, EC 3.5.4.4) gene, which determines the cellular level of adenosine and plays a crucial role in the regulation of the immune system and in the control of metabolic rates, is involved in longevity. 884 unrelated healthy individuals (age range 10-106 years, 400 males and 484 females) from central Italy were studied. ADA genotyping was performed by RFLP-PCR. Frequency distributions were compared using the chi-square test and a three-way contingency table analysis by a log linear model was applied to test independence between the variables. We found that ADA influences human life-span in a sex and age specific way. An increased frequency of ADA*2 carriers was found in males aged 80-85, and a decreased frequency in males over 85 (chi(2) = 13.93; df = 3; P = 0.003); significant differences among the age groups was not found in females. A strong interaction among age groups, ADA genotype and sex (G = 15.086; df = 3; P = 0.0017) was found. Males aged 80-85 could be protected from ischemic stroke by higher levels of adenosine (determined by the ADA*2 allele). The decrease of ADA*2 carriers in males over 85 may depend essentially on immunological factors; reduced levels of adenosine protect from asthma and other pulmonary diseases and lead to a reduced activation of inflammatory cells and pro-inflammatory cytokines production. Moreover, the low level of adenosine may potentiate the activity of NK and other cellular effectors against tumor cells. The negligible effect of ADA genetic polymorphism in females suggest a marginal influence of genetic factors in determining longevity in this sex, confirming previous reports.

Righting the ADA

Science.gov (United States)

National Council on Disability, 2004

2004-01-01

Many Americans with disabilities feel that a series of negative court decisions is reducing their status to that of "second-class citizens," a status that the Americans with Disabilities Act (ADA) was supposed to remedy forever. In this report, the National Council on Disability (NCD), which first proposed the enactment of an ADA and…

Real-time analytics with Storm and Cassandra

CERN Document Server

Saxena, Shilpi

2015-01-01

If you want to efficiently use Storm and Cassandra together and excel at developing production-grade, distributed real-time applications, then this book is for you. No prior knowledge of using Storm and Cassandra together is necessary. However, a background in Java is expected.

Real-time beam profile imaging system for actinotherapy accelerator

International Nuclear Information System (INIS)

Lin Yong; Wang Jingjin; Song Zheng; Zheng Putang; Wang Jianguo

2003-01-01

This paper describes a real-time beam profile imaging system for actinotheraphy accelerator. With the flash X-ray imager and the technique of digital image processing, a real-time 3-dimension dosage image is created from the intensity profile of the accelerator beam in real time. This system helps to obtain all the physical characters of the beam in any section plane, such as FWHM, penumbra, peak value, symmetry and homogeneity. This system has been used to acquire a 3-dimension dosage distribution of dynamic wedge modulator and the transient process of beam dosage. The system configure and the tested beam profile images are also presented

Design and Performance Evaluation of an Adaptive Resource Management Framework for Distributed Real-Time and Embedded Systems

Directory of Open Access Journals (Sweden)

Chen Yingming

2008-01-01

Full Text Available Abstract Achieving end-to-end quality of service (QoS in distributed real-time embedded (DRE systems require QoS support and enforcement from their underlying operating platforms that integrates many real-time capabilities, such as QoS-enabled network protocols, real-time operating system scheduling mechanisms and policies, and real-time middleware services. As standards-based quality of service (QoS enabled component middleware automates integration and configuration activities, it is increasingly being used as a platform for developing open DRE systems that execute in environments where operational conditions, input workload, and resource availability cannot be characterized accurately a priori. Although QoS-enabled component middleware offers many desirable features, however, it historically lacked the ability to allocate resources efficiently and enable the system to adapt to fluctuations in input workload, resource availability, and operating conditions. This paper presents three contributions to research on adaptive resource management for component-based open DRE systems. First, we describe the structure and functionality of the resource allocation and control engine (RACE, which is an open-source adaptive resource management framework built atop standards-based QoS-enabled component middleware. Second, we demonstrate and evaluate the effectiveness of RACE in the context of a representative open DRE system: NASA's magnetospheric multiscale mission system. Third, we present an empirical evaluation of RACE's scalability as the number of nodes and applications in a DRE system grows. Our results show that RACE is a scalable adaptive resource management framework and yields a predictable and high-performance system, even in the face of changing operational conditions and input workload.

Design and Performance Evaluation of an Adaptive Resource Management Framework for Distributed Real-Time and Embedded Systems

Directory of Open Access Journals (Sweden)

Chenyang Lu

2008-04-01

Full Text Available Achieving end-to-end quality of service (QoS in distributed real-time embedded (DRE systems require QoS support and enforcement from their underlying operating platforms that integrates many real-time capabilities, such as QoS-enabled network protocols, real-time operating system scheduling mechanisms and policies, and real-time middleware services. As standards-based quality of service (QoS enabled component middleware automates integration and configuration activities, it is increasingly being used as a platform for developing open DRE systems that execute in environments where operational conditions, input workload, and resource availability cannot be characterized accurately a priori. Although QoS-enabled component middleware offers many desirable features, however, it historically lacked the ability to allocate resources efficiently and enable the system to adapt to fluctuations in input workload, resource availability, and operating conditions. This paper presents three contributions to research on adaptive resource management for component-based open DRE systems. First, we describe the structure and functionality of the resource allocation and control engine (RACE, which is an open-source adaptive resource management framework built atop standards-based QoS-enabled component middleware. Second, we demonstrate and evaluate the effectiveness of RACE in the context of a representative open DRE system: NASA's magnetospheric multiscale mission system. Third, we present an empirical evaluation of RACE's scalability as the number of nodes and applications in a DRE system grows. Our results show that RACE is a scalable adaptive resource management framework and yields a predictable and high-performance system, even in the face of changing operational conditions and input workload.

Real-time safety risk assessment based on a real-time location system for hydropower construction sites.

Science.gov (United States)

Jiang, Hanchen; Lin, Peng; Fan, Qixiang; Qiang, Maoshan

2014-01-01

The concern for workers' safety in construction industry is reflected in many studies focusing on static safety risk identification and assessment. However, studies on real-time safety risk assessment aimed at reducing uncertainty and supporting quick response are rare. A method for real-time safety risk assessment (RTSRA) to implement a dynamic evaluation of worker safety states on construction site has been proposed in this paper. The method provides construction managers who are in charge of safety with more abundant information to reduce the uncertainty of the site. A quantitative calculation formula, integrating the influence of static and dynamic hazards and that of safety supervisors, is established to link the safety risk of workers with the locations of on-site assets. By employing the hidden Markov model (HMM), the RTSRA provides a mechanism for processing location data provided by the real-time location system (RTLS) and analyzing the probability distributions of different states in terms of false positives and negatives. Simulation analysis demonstrated the logic of the proposed method and how it works. Application case shows that the proposed RTSRA is both feasible and effective in managing construction project safety concerns.

A Distributed Computing Framework for Real-Time Detection of Stress and of Its Propagation in a Team.

Science.gov (United States)

Pandey, Parul; Lee, Eun Kyung; Pompili, Dario

2016-11-01

Stress is one of the key factor that impacts the quality of our daily life: From the productivity and efficiency in the production processes to the ability of (civilian and military) individuals in making rational decisions. Also, stress can propagate from one individual to other working in a close proximity or toward a common goal, e.g., in a military operation or workforce. Real-time assessment of the stress of individuals alone is, however, not sufficient, as understanding its source and direction in which it propagates in a group of people is equally-if not more-important. A continuous near real-time in situ personal stress monitoring system to quantify level of stress of individuals and its direction of propagation in a team is envisioned. However, stress monitoring of an individual via his/her mobile device may not always be possible for extended periods of time due to limited battery capacity of these devices. To overcome this challenge a novel distributed mobile computing framework is proposed to organize the resources in the vicinity and form a mobile device cloud that enables offloading of computation tasks in stress detection algorithm from resource constrained devices (low residual battery, limited CPU cycles) to resource rich devices. Our framework also supports computing parallelization and workflows, defining how the data and tasks divided/assigned among the entities of the framework are designed. The direction of propagation and magnitude of influence of stress in a group of individuals are studied by applying real-time, in situ analysis of Granger Causality. Tangible benefits (in terms of energy expenditure and execution time) of the proposed framework in comparison to a centralized framework are presented via thorough simulations and real experiments.

Migrating to a real-time distributed parallel simulator architecture- An update

CSIR Research Space (South Africa)

Duvenhage, B

2007-09-01

Full Text Available A legacy non-distributed logical time simulator was previously migrated to a distributed architecture to parallelise execution. The existing Discrete Time System Specification (DTSS) modelling formalism was retained to simplify the reuse of existing...

Frequency Based Real-time Pricing for Residential Prosumers

Science.gov (United States)

Hambridge, Sarah Mabel

This work is the first to explore frequency based pricing for secondary frequency control as a price-reactive control mechanism for residential prosumers. A frequency based real-time electricity rate is designed as an autonomous market control mechanism for residential prosumers to provide frequency support as an ancillary service. In addition, prosumers are empowered to participate in dynamic energy transactions, therefore integrating Distributed Energy Resources (DERs), and increasing distributed energy storage onto the distributed grid. As the grid transitions towards DERs, a new market based control system will take the place of the legacy distributed system and possibly the legacy bulk power system. DERs provide many benefits such as energy independence, clean generation, efficiency, and reliability to prosumers during blackouts. However, the variable nature of renewable energy and current lack of installed energy storage on the grid will create imbalances in supply and demand as uptake increases, affecting the grid frequency and system operation. Through a frequency-based electricity rate, prosumers will be encouraged to purchase energy storage systems (ESS) to offset their neighbor's distributed generation (DG) such as solar. Chapter 1 explains the deregulation of the power system and move towards Distributed System Operators (DSOs), as prosumers become owners of microgrids and energy cells connected to the distributed system. Dynamic pricing has been proposed as a benefit to prosumers, giving them the ability to make decisions in the energy market, while also providing a way to influence and control their behavior. Frequency based real-time pricing is a type of dynamic pricing which falls between price-reactive control and transactive control. Prosumer-to-prosumer transactions may take the place of prosumer-to-utility transactions, building The Energy Internet. Frequency based pricing could be a mechanism for determining prosumer prices and supporting

Regulation of adenosine deaminase (ADA) on induced mouse experimental autoimmune uveitis (EAU) ‡

Science.gov (United States)

Liang, Dongchun; Zuo, Aijun; Zhao, Ronglan; Shao, Hui; Kaplan, Henry J.; Sun, Deming

2016-01-01

Adenosine is an important regulator of the immune response and adenosine deaminase (ADA) inhibits this regulatory effect by converting adenosine into functionally inactive molecules. Studies have shown that adenosine receptor (AR) agonists can be either anti- or pro-inflammatory. Clarification of the mechanisms that cause these opposing effects should provide a better guide for therapeutic intervention. In this study, we investigated the effect of ADA on the development of experimental autoimmune uveitis (EAU) induced by immunizing EAU-prone mice with a known uveitogenic peptide, IRBP1–20. Our results showed that the effective time to administer a single dose of ADA to suppress induction of EAU was 8–14 days post-immunization, shortly before EAU expression, but ADA treatment at other time points exacerbated disease. ADA preferentially inhibited Th17 responses and this effect was γδ T cell-dependent. Our results demonstrated that the existing immune status strongly influences the anti- or proinflammatory effects of ADA. Our observations should help improve the design of ADA- and AR-targeted therapies. PMID:26856700

Cloud-Hosted Real-time Data Services for the Geosciences (CHORDS)

Science.gov (United States)

Daniels, M. D.; Graves, S. J.; Vernon, F.; Kerkez, B.; Chandra, C. V.; Keiser, K.; Martin, C.

2014-12-01

Cloud-Hosted Real-time Data Services for the Geosciences (CHORDS) Access, utilization and management of real-time data continue to be challenging for decision makers, as well as researchers in several scientific fields. This presentation will highlight infrastructure aimed at addressing some of the gaps in handling real-time data, particularly in increasing accessibility of these data to the scientific community through cloud services. The Cloud-Hosted Real-time Data Services for the Geosciences (CHORDS) system addresses the ever-increasing importance of real-time scientific data, particularly in mission critical scenarios, where informed decisions must be made rapidly. Advances in the distribution of real-time data are leading many new transient phenomena in space-time to be observed, however real-time decision-making is infeasible in many cases that require streaming scientific data as these data are locked down and sent only to proprietary in-house tools or displays. This lack of accessibility to the broader scientific community prohibits algorithm development and workflows initiated by these data streams. As part of NSF's EarthCube initiative, CHORDS proposes to make real-time data available to the academic community via cloud services. The CHORDS infrastructure will enhance the role of real-time data within the geosciences, specifically expanding the potential of streaming data sources in enabling adaptive experimentation and real-time hypothesis testing. Adherence to community data and metadata standards will promote the integration of CHORDS real-time data with existing standards-compliant analysis, visualization and modeling tools.

Subsurface Scattering-Based Object Rendering Techniques for Real-Time Smartphone Games

Directory of Open Access Journals (Sweden)

Won-Sun Lee

2014-01-01

Full Text Available Subsurface scattering that simulates the path of a light through the material in a scene is one of the advanced rendering techniques in the field of computer graphics society. Since it takes a number of long operations, it cannot be easily implemented in real-time smartphone games. In this paper, we propose a subsurface scattering-based object rendering technique that is optimized for smartphone games. We employ our subsurface scattering method that is utilized for a real-time smartphone game. And an example game is designed to validate how the proposed method can be operated seamlessly in real time. Finally, we show the comparison results between bidirectional reflectance distribution function, bidirectional scattering distribution function, and our proposed subsurface scattering method on a smartphone game.

Linux real-time framework for fusion devices

Energy Technology Data Exchange (ETDEWEB)

Neto, Andre [Associacao Euratom-IST, Instituto de Plasmas e Fusao Nuclear, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)], E-mail: andre.neto@cfn.ist.utl.pt; Sartori, Filippo; Piccolo, Fabio [Euratom-UKAEA, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Barbalace, Antonio [Euratom-ENEA Association, Consorzio RFX, 35127 Padova (Italy); Vitelli, Riccardo [Dipartimento di Informatica, Sistemi e Produzione, Universita di Roma, Tor Vergata, Via del Politecnico 1-00133, Roma (Italy); Fernandes, Horacio [Associacao Euratom-IST, Instituto de Plasmas e Fusao Nuclear, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

2009-06-15

A new framework for the development and execution of real-time codes is currently being developed and commissioned at JET. The foundations of the system are Linux, the Real Time Application Interface (RTAI) and a wise exploitation of the new i386 multi-core processors technology. The driving motivation was the need to find a real-time operating system for the i386 platform able to satisfy JET Vertical Stabilisation Enhancement project requirements: 50 {mu}s cycle time. Even if the initial choice was the VxWorks operating system, it was decided to explore an open source alternative, mostly because of the costs involved in the commercial product. The work started with the definition of a precise set of requirements and milestones to achieve: Linux distribution and kernel versions to be used for the real-time operating system; complete characterization of the Linux/RTAI real-time capabilities; exploitation of the multi-core technology; implementation of all the required and missing features; commissioning of the system. Latency and jitter measurements were compared for Linux and RTAI in both user and kernel-space. The best results were attained using the RTAI kernel solution where the time to reschedule a real-time task after an external interrupt is of 2.35 {+-} 0.35 {mu}s. In order to run the real-time codes in the kernel-space, a solution to provide user-space functionalities to the kernel modules had to be designed. This novel work provided the most common functions from the standard C library and transparent interaction with files and sockets to the kernel real-time modules. Kernel C++ support was also tested, further developed and integrated in the framework. The work has produced very convincing results so far: complete isolation of the processors assigned to real-time from the Linux non real-time activities, high level of stability over several days of benchmarking operations and values well below 3 {mu}s for task rescheduling after external interrupt. From

Linux real-time framework for fusion devices

International Nuclear Information System (INIS)

Neto, Andre; Sartori, Filippo; Piccolo, Fabio; Barbalace, Antonio; Vitelli, Riccardo; Fernandes, Horacio

2009-01-01

A new framework for the development and execution of real-time codes is currently being developed and commissioned at JET. The foundations of the system are Linux, the Real Time Application Interface (RTAI) and a wise exploitation of the new i386 multi-core processors technology. The driving motivation was the need to find a real-time operating system for the i386 platform able to satisfy JET Vertical Stabilisation Enhancement project requirements: 50 μs cycle time. Even if the initial choice was the VxWorks operating system, it was decided to explore an open source alternative, mostly because of the costs involved in the commercial product. The work started with the definition of a precise set of requirements and milestones to achieve: Linux distribution and kernel versions to be used for the real-time operating system; complete characterization of the Linux/RTAI real-time capabilities; exploitation of the multi-core technology; implementation of all the required and missing features; commissioning of the system. Latency and jitter measurements were compared for Linux and RTAI in both user and kernel-space. The best results were attained using the RTAI kernel solution where the time to reschedule a real-time task after an external interrupt is of 2.35 ± 0.35 μs. In order to run the real-time codes in the kernel-space, a solution to provide user-space functionalities to the kernel modules had to be designed. This novel work provided the most common functions from the standard C library and transparent interaction with files and sockets to the kernel real-time modules. Kernel C++ support was also tested, further developed and integrated in the framework. The work has produced very convincing results so far: complete isolation of the processors assigned to real-time from the Linux non real-time activities, high level of stability over several days of benchmarking operations and values well below 3 μs for task rescheduling after external interrupt. From being the

Specifying and verifying requirements of real-time systems

DEFF Research Database (Denmark)

Ravn, Anders P.; Rischel, Hans; Hansen, Kirsten Mark

1993-01-01

, a real-time interval logic, where predicates define durations of states. Requirements define safety and functionality constraints on the system or a component. A top-level design is given by a control law: a predicate that defines an automation controlling the transition between phases of operation. Each......An approach to specification of requirements and verification of design for real-time systems is presented. A system is defined by a conventional mathematical model for a dynamic system where application specific states denote functions of real time. Specifications are formulas in duration calculus...... phase maintains certain relations among the system states; this is analogous to the control functions known from conventional control theory. The top-level design is decomposed into an architecture for a distributed system with specifications for sensor, actuator, and program components. Programs...

From distributed to multicore architecture in the RFX-mod real time control system

International Nuclear Information System (INIS)

Manduchi, G.; Luchetta, A.; Soppelsa, A.; Taliercio, C.

2014-01-01

Highlights: • The paper describes the experience in running the real-time control system of RFX-mod. • It presents a new architecture based on multicore technology. • It analyze the feasibility of Linux MRG for real-time control. • It presents an application of the MARTe framework. - Abstract: The real-time control system of RFX has been operating since 2004 providing effective control of the plasma position and of the MagnetoHydroDynamic (MHD) modes. The demand for new and more computing-intensive control algorithms and the need for shorter latency pushed the system to its limits and, thus, a complete re-design was carried out in 2012. The new system adopts radically different solutions in hardware, operating system and software management. The VME PowerPC CPUs communicating over Ethernet have been now replaced by a single multicore server. VxWorks, previously used in the VME CPUs has now been replaced by Linux, which can be currently considered a real-time system provided an accurate tuning of the Linux scheduler and interrupt configuration. The previous framework for control and communication has been replaced by MARTe, a modern framework for real-time control gaining interest in the fusion community. The usage of MARTe allowed a rapid development of the control system and, in particular, its intrinsic simulation ability gave us the possibility of carrying out most debugging in simulation, without affecting machine operation. As a result the whole system has been finally commissioned in RFX in only two weeks

From distributed to multicore architecture in the RFX-mod real time control system

Energy Technology Data Exchange (ETDEWEB)

Manduchi, G., E-mail: gabriele.manduchi@igi.cnr.it; Luchetta, A.; Soppelsa, A.; Taliercio, C.

2014-03-15

Highlights: • The paper describes the experience in running the real-time control system of RFX-mod. • It presents a new architecture based on multicore technology. • It analyze the feasibility of Linux MRG for real-time control. • It presents an application of the MARTe framework. - Abstract: The real-time control system of RFX has been operating since 2004 providing effective control of the plasma position and of the MagnetoHydroDynamic (MHD) modes. The demand for new and more computing-intensive control algorithms and the need for shorter latency pushed the system to its limits and, thus, a complete re-design was carried out in 2012. The new system adopts radically different solutions in hardware, operating system and software management. The VME PowerPC CPUs communicating over Ethernet have been now replaced by a single multicore server. VxWorks, previously used in the VME CPUs has now been replaced by Linux, which can be currently considered a real-time system provided an accurate tuning of the Linux scheduler and interrupt configuration. The previous framework for control and communication has been replaced by MARTe, a modern framework for real-time control gaining interest in the fusion community. The usage of MARTe allowed a rapid development of the control system and, in particular, its intrinsic simulation ability gave us the possibility of carrying out most debugging in simulation, without affecting machine operation. As a result the whole system has been finally commissioned in RFX in only two weeks.

Specification and Test of Real-Time Systems

DEFF Research Database (Denmark)

Nielsen, Brian

of the system, and a set of constraint patterns which describes and enforces the timing and synchronization constraints among components. We propose new techniques for automated black box conformance testing of real-time systems against densely timed speci cations. A test generator tool examines a specification......Distributed real-time computer based systems are very complex and intrinsically difficult to specify and implement correctly; in part this is caused by the overwhelming number of possible interactions between system components, but especially by a lack of adequate methods and tools to deal...... of the desired system behavior and generates the necessary test cases. A main problem is to construct a reasonably small test suite that can be executed within allotted resources, while having a high likelihood of detecting unknown errors. Our goal has been to treat the time dimension of this problem thoroughly...

Real-time monitoring of single-photon detectors against eavesdropping in quantum key distribution systems.

Science.gov (United States)

da Silva, Thiago Ferreira; Xavier, Guilherme B; Temporão, Guilherme P; von der Weid, Jean Pierre

2012-08-13

By employing real-time monitoring of single-photon avalanche photodiodes we demonstrate how two types of practical eavesdropping strategies, the after-gate and time-shift attacks, may be detected. Both attacks are identified with the detectors operating without any special modifications, making this proposal well suited for real-world applications. The monitoring system is based on accumulating statistics of the times between consecutive detection events, and extracting the afterpulse and overall efficiency of the detectors in real-time using mathematical models fit to the measured data. We are able to directly observe changes in the afterpulse probabilities generated from the after-gate and faint after-gate attacks, as well as different timing signatures in the time-shift attack. We also discuss the applicability of our scheme to other general blinding attacks.

Using Ada to implement the operations management system in a community of experts

Science.gov (United States)

Frank, M. S.

1986-01-01

An architecture is described for the Space Station Operations Management System (OMS), consisting of a distributed expert system framework implemented in Ada. The motivation for such a scheme is based on the desire to integrate the very diverse elements of the OMS while taking maximum advantage of knowledge based systems technology. Part of the foundation of an Ada based distributed expert system was accomplished in the form of a proof of concept prototype for the KNOMES project (Knowledge-based Maintenance Expert System). This prototype successfully used concurrently active experts to accomplish monitoring and diagnosis for the Remote Manipulator System. The basic concept of this software architecture is named ACTORS for Ada Cognitive Task ORganization Scheme. It is when one considers the overall problem of integrating all of the OMS elements into a cooperative system that the AI solution stands out. By utilizing a distributed knowledge based system as the framework for OMS, it is possible to integrate those components which need to share information in an intelligent manner.

Object-oriented programming with mixins in Ada

Science.gov (United States)

Seidewitz, ED

1992-01-01

Recently, I wrote a paper discussing the lack of 'true' object-oriented programming language features in Ada 83, why one might desire them in Ada, and how they might be added in Ada 9X. The approach I took in this paper was to build the new object-oriented features of Ada 9X as much as possible on the basic constructs and philosophy of Ada 83. The object-oriented features proposed for Ada 9X, while different in detail, are based on the same kind of approach. Further consideration of this approach led me on a long reflection on the nature of object-oriented programming and its application to Ada. The results of this reflection, presented in this paper, show how a fairly natural object-oriented style can indeed be developed even in Ada 83. The exercise of developing this style is useful for at least three reasons: (1) it provides a useful style for programming object-oriented applications in Ada 83 until new features become available with Ada 9X; (2) it demystifies many of the mechanisms that seem to be 'magic' in most object-oriented programming languages by making them explicit; and (3) it points out areas that are and are not in need of change in Ada 83 to make object-oriented programming more natural in Ada 9X. In the next four sections I will address in turn the issues of object-oriented classes, mixins, self-reference and supertyping. The presentation is through a sequence of examples. This results in some overlap with that paper, but all the examples in the present paper are written entirely in Ada 83. I will return to considerations for Ada 9X in the last section of the paper.

Real-time particle image velocimetry based on FPGA technology

International Nuclear Information System (INIS)

Iriarte Munoz, Jose Miguel

2008-01-01

Particle image velocimetry (PIV), based on laser sheet, is a method for image processing and calculation of distributed velocity fields.It is well established as a fluid dynamics measurement tool, being applied to liquid, gases and multiphase flows.Images of particles are processed by means of computationally demanding algorithms, what makes its real-time implementation difficult.The most probable displacements are found applying two dimensional cross-correlation function. In this work, we detail how it is possible to achieve real-time visualization of PIV method by designing an adaptive embedded architecture based on FPGA technology.We show first results of a physical field of velocity calculated by this platform system in a real-time approach. [es

The Raptor Real-Time Processing Architecture

Science.gov (United States)

Galassi, M.; Starr, D.; Wozniak, P.; Brozdin, K.

The primary goal of Raptor is ambitious: to identify interesting optical transients from very wide field of view telescopes in real time, and then to quickly point the higher resolution Raptor ``fovea'' cameras and spectrometer to the location of the optical transient. The most interesting of Raptor's many applications is the real-time search for orphan optical counterparts of Gamma Ray Bursts. The sequence of steps (data acquisition, basic calibration, source extraction, astrometry, relative photometry, the smarts of transient identification and elimination of false positives, telescope pointing feedback, etc.) is implemented with a ``component'' approach. All basic elements of the pipeline functionality have been written from scratch or adapted (as in the case of SExtractor for source extraction) to form a consistent modern API operating on memory resident images and source lists. The result is a pipeline which meets our real-time requirements and which can easily operate as a monolithic or distributed processing system. Finally, the Raptor architecture is entirely based on free software (sometimes referred to as ``open source'' software). In this paper we also discuss the interplay between various free software technologies in this type of astronomical problem.

Real-time change detection in data streams with FPGAs

International Nuclear Information System (INIS)

Vega, J.; Dormido-Canto, S.; Cruz, T.; Ruiz, M.; Barrera, E.; Castro, R.; Murari, A.; Ochando, M.

2014-01-01

Highlights: • Automatic recognition of changes in data streams of multidimensional signals. • Detection algorithm based on testing exchangeability on-line. • Real-time and off-line applicability. • Real-time implementation in FPGAs. - Abstract: The automatic recognition of changes in data streams is useful in both real-time and off-line data analyses. This article shows several effective change-detecting algorithms (based on martingales) and describes their real-time applicability in the data acquisition systems through the use of Field Programmable Gate Arrays (FPGA). The automatic event recognition system is absolutely general and it does not depend on either the particular event to detect or the specific data representation (waveforms, images or multidimensional signals). The developed approach provides good results for change detection in both the temporal evolution of profiles and the two-dimensional spatial distribution of volume emission intensity. The average computation time in the FPGA is 210 μs per profile

Formal methods in the design of Ada 1995

Science.gov (United States)

Guaspari, David

1995-01-01

Formal, mathematical methods are most useful when applied early in the design and implementation of a software system--that, at least, is the familiar refrain. I will report on a modest effort to apply formal methods at the earliest possible stage, namely, in the design of the Ada 95 programming language itself. This talk is an 'experience report' that provides brief case studies illustrating the kinds of problems we worked on, how we approached them, and the extent (if any) to which the results proved useful. It also derives some lessons and suggestions for those undertaking future projects of this kind. Ada 95 is the first revision of the standard for the Ada programming language. The revision began in 1988, when the Ada Joint Programming Office first asked the Ada Board to recommend a plan for revising the Ada standard. The first step in the revision was to solicit criticisms of Ada 83. A set of requirements for the new language standard, based on those criticisms, was published in 1990. A small design team, the Mapping Revision Team (MRT), became exclusively responsible for revising the language standard to satisfy those requirements. The MRT, from Intermetrics, is led by S. Tucker Taft. The work of the MRT was regularly subject to independent review and criticism by a committee of distinguished Reviewers and by several advisory teams--for example, the two User/Implementor teams, each consisting of an industrial user (attempting to make significant use of the new language on a realistic application) and a compiler vendor (undertaking, experimentally, to modify its current implementation in order to provide the necessary new features). One novel decision established the Language Precision Team (LPT), which investigated language proposals from a mathematical point of view. The LPT applied formal mathematical analysis to help improve the design of Ada 95 (e.g., by clarifying the language proposals) and to help promote its acceptance (e.g., by identifying a

Real-time shadows

CERN Document Server

Eisemann, Elmar; Assarsson, Ulf; Wimmer, Michael

2011-01-01

Important elements of games, movies, and other computer-generated content, shadows are crucial for enhancing realism and providing important visual cues. In recent years, there have been notable improvements in visual quality and speed, making high-quality realistic real-time shadows a reachable goal. Real-Time Shadows is a comprehensive guide to the theory and practice of real-time shadow techniques. It covers a large variety of different effects, including hard, soft, volumetric, and semi-transparent shadows.The book explains the basics as well as many advanced aspects related to the domain

Injection moulded microneedle sensor for real-time wireless pH monitoring.

Science.gov (United States)

Mirza, Khalid B; Zuliani, Claudio; Hou, Benjamin; Ng, Fu Siong; Peters, Nicholas S; Toumazou, Christofer

2017-07-01

This paper describes the development of an array of individually addressable pH sensitive microneedles using injection moulding and their integration within a portable device for real-time wireless recording of pH distributions in biological samples. The fabricated microneedles are subjected to gold patterning followed by electrodeposition of iridium oxide to sensitize them to 0.07 units of pH change. Miniaturised electronics suitable for the sensors readout, analog-to-digital conversion and wireless transmission of the potentiometric data are embodied within the device, enabling it to measure real-time pH of soft biological samples such as muscles. In this paper, real-time recording of the cardiac pH distribution, during ischemia followed by reperfusion cycles in cardiac muscles of male Wistar rats has been demonstrated by using the microneedle array.

Dependable Real-Time Systems

Science.gov (United States)

1991-09-30

0196 or 413 545-0720 PI E-mail Address: krithi@nirvan.cs.umass.edu, stankovic(ocs.umass.edu Grant or Contract Title: Dependable Real - Time Systems Grant...Dependable Real - Time Systems " Grant or Contract Number: N00014-85-k-0398 L " Reporting Period: 1 Oct 87 - 30 Sep 91 , 2. Summary of Accomplishments ’ 2.1 Our...in developing a sound approach to scheduling tasks in complex real - time systems , (2) developed a real-time operating system kernel, a preliminary

Real time Faraday spectrometer

Science.gov (United States)

Smith, Jr., Tommy E.; Struve, Kenneth W.; Colella, Nicholas J.

1991-01-01

This invention uses a dipole magnet to bend the path of a charged particle beam. As the deflected particles exit the magnet, they are spatially dispersed in the bend-plane of the magnet according to their respective momenta and pass to a plurality of chambers having Faraday probes positioned therein. Both the current and energy distribution of the particles is then determined by the non-intersecting Faraday probes located along the chambers. The Faraday probes are magnetically isolated from each other by thin metal walls of the chambers, effectively providing real time current-versus-energy particle measurements.

Real time Faraday spectrometer

International Nuclear Information System (INIS)

Smith, T.E.; Struve, K.W.; Colella, N.J.

1991-01-01

This patent describes an invention which uses a dipole magnet to bend the path of a charged particle beam. As the deflected particles exit the magnet, they are spatially dispersed in the bend-plane of the magnet according to their respective momenta and pass to a plurality of chambers having Faraday probes positioned therein. Both the current and energy distribution of the particles is then determined by the non-intersecting Faraday probes located along the chambers. The Faraday probes are magnetically isolated from each other by thin metal walls of the chambers, effectively providing real time current-versus-energy particle measurements

LabVIEW Real-Time

CERN Multimedia

CERN. Geneva; Flockhart, Ronald Bruce; Seppey, P

2003-01-01

With LabVIEW Real-Time, you can choose from a variety of RT Series hardware. Add a real-time data acquisition component into a larger measurement and automation system or create a single stand-alone real-time solution with data acquisition, signal conditioning, motion control, RS-232, GPIB instrumentation, and Ethernet connectivity. With the various hardware options, you can create a system to meet your precise needs today, while the modularity of the system means you can add to the solution as your system requirements grow. If you are interested in Reliable and Deterministic systems for Measurement and Automation, you will profit from this seminar. Agenda: Real-Time Overview LabVIEW RT Hardware Platforms - Linux on PXI Programming with LabVIEW RT Real-Time Operating Systems concepts Timing Applications Data Transfer

Predictive value of 6-month decline in ADAS-cog for survival without severe Alzheimer's disease.

Science.gov (United States)

Helmer, Catherine; Andrieu, Sandrine; Pérès, Karine; Orgogozo, Jean-Marc; Vellas, Bruno; Dartigues, Jean-François

2007-01-01

To determine the predictive value of the 6-month evolution of the ADAS-cog score in initially mild to moderate Alzheimer's disease (AD) patients on the risk of death or severe dementia (MMSE ADAS-cog scale in the Real.fr study, a cohort of AD patients. Six classes of ADAS-cog evolution were distinguished, from the severest deterioration (decline >or=7 points) to the greatest cognitive improvement (gain >or=4 points). Among 536 AD patients, 53 (9.9%) had a 6-month decline of 7 points or more. This group with the severest deterioration was significantly associated with the risk of severe dementia or death at 2 years (relative risk, RR = 3.8, 95% confidence interval, CI = 2.1-6.8), even after adjustment for baseline MMSE, disability and ADAS-cog score (RR = 2.6, 95% CI = 1.4-5.0). In addition, subjects with a decline by at least 4 points were also at greater risk of severe dementia. These results confirm the value of the ADAS-cog scale as a judgement criterion in clinical trials since it is a good surrogate marker of long-term prognosis. The proportion of fast decliners on the ADAS-cog could be a helpful judgement criterion for future trials in AD.

Concepts of real time and semi-real time material control

International Nuclear Information System (INIS)

Lovett, J.E.

1975-01-01

After a brief consideration of the traditional material balance accounting on an MBA basis, this paper explores the basic concepts of real time and semi-real time material control, together with some of the major problems to be solved. Three types of short-term material control are discussed: storage, batch processing, and continuous processing. (DLC)

Real Time Systems

DEFF Research Database (Denmark)

Christensen, Knud Smed

2000-01-01

Describes fundamentals of parallel programming and a kernel for that. Describes methods for modelling and checking parallel problems. Real time problems.......Describes fundamentals of parallel programming and a kernel for that. Describes methods for modelling and checking parallel problems. Real time problems....

Real time expert systems

International Nuclear Information System (INIS)

Asami, Tohru; Hashimoto, Kazuo; Yamamoto, Seiichi

1992-01-01

Recently, aiming at the application to the plant control for nuclear reactors and traffic and communication control, the research and the practical use of the expert system suitable to real time processing have become conspicuous. In this report, the condition for the required function to control the object that dynamically changes within a limited time is presented, and the technical difference between the real time expert system developed so as to satisfy it and the expert system of conventional type is explained with the actual examples and from theoretical aspect. The expert system of conventional type has the technical base in the problem-solving equipment originating in STRIPS. The real time expert system is applied to the fields accompanied by surveillance and control, to which conventional expert system is hard to be applied. The requirement for the real time expert system, the example of the real time expert system, and as the techniques of realizing real time processing, the realization of interruption processing, dispersion processing, and the mechanism of maintaining the consistency of knowledge are explained. (K.I.)

Real-time control systems: feedback, scheduling and robustness

Science.gov (United States)

Simon, Daniel; Seuret, Alexandre; Sename, Olivier

2017-08-01

The efficient control of real-time distributed systems, where continuous components are governed through digital devices and communication networks, needs a careful examination of the constraints arising from the different involved domains inside co-design approaches. Thanks to the robustness of feedback control, both new control methodologies and slackened real-time scheduling schemes are proposed beyond the frontiers between these traditionally separated fields. A methodology to design robust aperiodic controllers is provided, where the sampling interval is considered as a control variable of the system. Promising experimental results are provided to show the feasibility and robustness of the approach.

Real-Time Multiprocessor Programming Language (RTMPL) user's manual

Science.gov (United States)

Arpasi, D. J.

1985-01-01

A real-time multiprocessor programming language (RTMPL) has been developed to provide for high-order programming of real-time simulations on systems of distributed computers. RTMPL is a structured, engineering-oriented language. The RTMPL utility supports a variety of multiprocessor configurations and types by generating assembly language programs according to user-specified targeting information. Many programming functions are assumed by the utility (e.g., data transfer and scaling) to reduce the programming chore. This manual describes RTMPL from a user's viewpoint. Source generation, applications, utility operation, and utility output are detailed. An example simulation is generated to illustrate many RTMPL features.

A real-time data-acquisition and analysis system with distributed UNIX workstations

International Nuclear Information System (INIS)

Yamashita, H.; Miyamoto, K.; Maruyama, K.; Hirosawa, H.; Nakayoshi, K.; Emura, T.; Sumi, Y.

1996-01-01

A compact data-acquisition system using three RISC/UNIX TM workstations (SUN TM /SPARCstation TM ) with real-time capabilities of monitoring and analysis has been developed for the study of photonuclear reactions with the large-acceptance spectrometer TAGX. One workstation acquires data from memory modules in the front-end electronics (CAMAC and TKO) with a maximum speed of 300 Kbytes/s, where data size times instantaneous rate is 1 Kbyte x 300 Hz. Another workstation, which has real-time capability for run monitoring, gets the data with a buffer manager called NOVA. The third workstation analyzes the data and reconstructs the event. In addition to a general hardware and software description, priority settings and run control by shell scripts are described. This system has recently been used successfully in a two month long experiment. (orig.)

Modeling Just-in-Time Communication On the Optimal Resource Utilization in Distributed Real-Time Multimedia Applications

NARCIS (Netherlands)

R. Yang (Ran); R.D. van der Mei (Rob); D. Roubos; F.J. Seinstra; H. Bal

2012-01-01

htmlabstractThe applications of multimedia content analysis (MMCA) operating in real-time environments must run under extremely strict time constraints. To meet these requirements, large-scale multimedia applications are typically executed on Grid systems consisting of large collections of

Modeling Just-in-Time Communication On the Optimal Resource Utilization in Distributed Real-Time Multimedia Applications

NARCIS (Netherlands)

R. Yang (Ran); R.D. van der Mei (Rob); D. Roubos; F.J. Seinstra; H. Bal

2011-01-01

htmlabstractThe applications of multimedia content analysis (MMCA) operating in real-time environments must run under extremely strict time constraints. To meet these requirements, large-scale multimedia applications are typically executed on Grid systems consisting of large collections of

Data acquisition and real-time bolometer tomography using LabVIEW RT

International Nuclear Information System (INIS)

Giannone, L.; Eich, T.; Fuchs, J.C.; Ravindran, M.; Ruan, Q.; Wenzel, L.; Cerna, M.; Concezzi, S.

2011-01-01

The currently available multi-core PCI Express systems running LabVIEW RT (real-time), equipped with FPGA cards for data acquisition and real-time parallel signal processing, greatly shorten the design and implementation cycles of large-scale, real-time data acquisition and control systems. This paper details a data acquisition and real-time tomography system using LabVIEW RT for the bolometer diagnostic on the ASDEX Upgrade tokamak (Max Planck Institute for Plasma Physics, Garching, Germany). The transformation matrix for tomography is pre-computed based on the geometry of distributed radiation sources and sensors. A parallelized iterative algorithm is adapted to solve a constrained linear system for the reconstruction of the radiated power density. Real-time bolometer tomography is performed with LabVIEW RT. Using multi-core machines to execute the parallelized algorithm, a cycle time well below 1 ms is reached.

Optical chaos and hybrid WDM/TDM based large capacity quasi-distributed sensing network with real-time fiber fault monitoring.

Science.gov (United States)

Luo, Yiyang; Xia, Li; Xu, Zhilin; Yu, Can; Sun, Qizhen; Li, Wei; Huang, Di; Liu, Deming

2015-02-09

An optical chaos and hybrid wavelength division multiplexing/time division multiplexing (WDM/TDM) based large capacity quasi-distributed sensing network with real-time fiber fault monitoring is proposed. Chirped fiber Bragg grating (CFBG) intensity demodulation is adopted to improve the dynamic range of the measurements. Compared with the traditional sensing interrogation methods in time, radio frequency and optical wavelength domains, the measurand sensing and the precise locating of the proposed sensing network can be simultaneously interrogated by the relative amplitude change (RAC) and the time delay of the correlation peak in the cross-correlation spectrum. Assisted with the WDM/TDM technology, hundreds of sensing units could be potentially multiplexed in the multiple sensing fiber lines. Based on the proof-of-concept experiment for axial strain measurement with three sensing fiber lines, the strain sensitivity up to 0.14% RAC/με and the precise locating of the sensors are achieved. Significantly, real-time fiber fault monitoring in the three sensing fiber lines is also implemented with a spatial resolution of 2.8 cm.

Performance results of cooperating expert systems in a distributed real-time monitoring system

Science.gov (United States)

Schwuttke, U. M.; Veregge, J. R.; Quan, A. G.

1994-01-01

There are numerous definitions for real-time systems, the most stringent of which involve guaranteeing correct system response within a domain-dependent or situationally defined period of time. For applications such as diagnosis, in which the time required to produce a solution can be non-deterministic, this requirement poses a unique set of challenges in dynamic modification of solution strategy that conforms with maximum possible latencies. However, another definition of real time is relevant in the case of monitoring systems where failure to supply a response in the proper (and often infinitesimal) amount of time allowed does not make the solution less useful (or, in the extreme example of a monitoring system responsible for detecting and deflecting enemy missiles, completely irrelevant). This more casual definition involves responding to data at the same rate at which it is produced, and is more appropriate for monitoring applications with softer real-time constraints, such as interplanetary exploration, which results in massive quantities of data transmitted at the speed of light for a number of hours before it even reaches the monitoring system. The latter definition of real time has been applied to the MARVEL system for automated monitoring and diagnosis of spacecraft telemetry. An early version of this system has been in continuous operational use since it was first deployed in 1989 for the Voyager encounter with Neptune. This system remained under incremental development until 1991 and has been under routine maintenance in operations since then, while continuing to serve as an artificial intelligence (AI) testbed in the laboratory. The system architecture has been designed to facilitate concurrent and cooperative processing by multiple diagnostic expert systems in a hierarchical organization. The diagnostic modules adhere to concepts of data-driven reasoning, constrained but complete nonoverlapping domains, metaknowledge of global consequences of anomalous

Change Semantic Constrained Online Data Cleaning Method for Real-Time Observational Data Stream

Science.gov (United States)

Ding, Yulin; Lin, Hui; Li, Rongrong

2016-06-01

Recent breakthroughs in sensor networks have made it possible to collect and assemble increasing amounts of real-time observational data by observing dynamic phenomena at previously impossible time and space scales. Real-time observational data streams present potentially profound opportunities for real-time applications in disaster mitigation and emergency response, by providing accurate and timeliness estimates of environment's status. However, the data are always subject to inevitable anomalies (including errors and anomalous changes/events) caused by various effects produced by the environment they are monitoring. The "big but dirty" real-time observational data streams can rarely achieve their full potential in the following real-time models or applications due to the low data quality. Therefore, timely and meaningful online data cleaning is a necessary pre-requisite step to ensure the quality, reliability, and timeliness of the real-time observational data. In general, a straightforward streaming data cleaning approach, is to define various types of models/classifiers representing normal behavior of sensor data streams and then declare any deviation from this model as normal or erroneous data. The effectiveness of these models is affected by dynamic changes of deployed environments. Due to the changing nature of the complicated process being observed, real-time observational data is characterized by diversity and dynamic, showing a typical Big (Geo) Data characters. Dynamics and diversity is not only reflected in the data values, but also reflected in the complicated changing patterns of the data distributions. This means the pattern of the real-time observational data distribution is not stationary or static but changing and dynamic. After the data pattern changed, it is necessary to adapt the model over time to cope with the changing patterns of real-time data streams. Otherwise, the model will not fit the following observational data streams, which may led

CHANGE SEMANTIC CONSTRAINED ONLINE DATA CLEANING METHOD FOR REAL-TIME OBSERVATIONAL DATA STREAM

Directory of Open Access Journals (Sweden)

Y. Ding

2016-06-01

Full Text Available Recent breakthroughs in sensor networks have made it possible to collect and assemble increasing amounts of real-time observational data by observing dynamic phenomena at previously impossible time and space scales. Real-time observational data streams present potentially profound opportunities for real-time applications in disaster mitigation and emergency response, by providing accurate and timeliness estimates of environment’s status. However, the data are always subject to inevitable anomalies (including errors and anomalous changes/events caused by various effects produced by the environment they are monitoring. The “big but dirty” real-time observational data streams can rarely achieve their full potential in the following real-time models or applications due to the low data quality. Therefore, timely and meaningful online data cleaning is a necessary pre-requisite step to ensure the quality, reliability, and timeliness of the real-time observational data. In general, a straightforward streaming data cleaning approach, is to define various types of models/classifiers representing normal behavior of sensor data streams and then declare any deviation from this model as normal or erroneous data. The effectiveness of these models is affected by dynamic changes of deployed environments. Due to the changing nature of the complicated process being observed, real-time observational data is characterized by diversity and dynamic, showing a typical Big (Geo Data characters. Dynamics and diversity is not only reflected in the data values, but also reflected in the complicated changing patterns of the data distributions. This means the pattern of the real-time observational data distribution is not stationary or static but changing and dynamic. After the data pattern changed, it is necessary to adapt the model over time to cope with the changing patterns of real-time data streams. Otherwise, the model will not fit the following observational

Ada--Programming Language of the Future.

Science.gov (United States)

Rudd, David

1983-01-01

Ada is a programing language developed for the Department of Defense, with a registered trademark. It was named for Ada Augusta, coworker of Charles Babbage and the world's first programer. The Department of Defense hopes to prevent variations and to establish Ada as a consistent, standardized language. (MNS)

Real-Time Energy Management System for a Hybrid AC/DC Residential Microgrid

DEFF Research Database (Denmark)

Diaz, Enrique Rodriguez; Palacios-Garcia, Emilio J.; Anvari-Moghaddam, Amjad

2017-01-01

This paper proposes real-time Energy Management System (EMS) for a residential hybrid ac/dc microgrid. The residential microgrid is organized in two different distribution systems. A dc distribution bus which interconnect the renewable energy sources (RES), energy storage systems (ESS...... buildings. This architecture increases the overall efficiency of the distribution by interconnecting the RES and ESS thorough a dc distribution bus, and therefore avoiding unnecessary dc/ac conversion stages. The real-time EMS performs an 24 hours ahead optimization in order to schedule the charge...... setup. The results shown how the operational costs of the system are effectively decreased by 28%, even with non-accurate estimation of the RES generation or building parameters....

Designing real-time systems based on mono-master Profibus-DP networks

OpenAIRE

Monforte, Salvatore; Alves, Mário; Vasques, Francisco; Tovar, Eduardo

2000-01-01

Profibus networks are widely used as the communication infrastructure for supporting distributed computer-controlled applications. Most of the times, these applications impose strict real-time requirements. Profibus-DP has gradually become the preferred Profibus application profile. It is usually implemented as a mono-master Profibus network, and is optimised for speed and efficiency. The aim of this paper is to analyse the real-time behaviour of this class of Profibus networks...

Integrated Oil spill detection and forecasting using MOON real time data

OpenAIRE

De Dominicis, M.; Pinardi, N.; Coppini, G.; Tonani, M.; Guarnieri, A.; Zodiatis, G.; Lardner, R.; Santoleri, R.

2009-01-01

MOON (Mediterranean Operational Oceanography Network) is an operational distributed system ready to provide quality controlled and timely marine observations (in situ and satellite) and environmental analyses and predictions for management of oil spill accidents. MOON operational systems are based upon the real time functioning of an integrated system composed of the Real Time Observing system, the regional, sub-regional and coastal forecasting systems and a products dissemination system. All...

Real-time ArcGIS and heterotrophic plate count based chloramine disinfectant control in water distribution system.

Science.gov (United States)

Bai, Xiaohui; Zhi, Xinghua; Zhu, Huifeng; Meng, Mingqun; Zhang, Mingde

2015-01-01

This study investigates the effect of chloramine residual on bacteria growth and regrowth and the relationship between heterotrophic plate counts (HPCs) and the concentration of chloramine residual in the Shanghai drinking water distribution system (DWDS). In this study, models to control HPCs in the water distribution system and consumer taps are also developed. Real-time ArcGIS was applied to show the distribution and changed results of the chloramine residual concentration in the pipe system by using these models. Residual regression analysis was used to get a reasonable range of the threshold values that allows the chloramine residual to efficiently inhibit bacteria growth in the Shanghai DWDS; the threshold values should be between 0.45 and 0.5 mg/L in pipe water and 0.2 and 0.25 mg/L in tap water. The low residual chloramine value (0.05 mg/L) of the Chinese drinking water quality standard may pose a potential health risk for microorganisms that should be improved. Disinfection by-products (DBPs) were detected, but no health risk was identified.

Real-time optoacoustic monitoring of temperature in tissues

International Nuclear Information System (INIS)

Larina, Irina V; Larin, Kirill V; Esenaliev, Rinat O

2005-01-01

To improve the safety and efficacy of thermal therapy, it is necessary to map tissue temperature in real time with submillimetre spatial resolution. Accurate temperature maps may provide the necessary control of the boundaries of the heated regions and minimize thermal damage to surrounding normal tissues. Current imaging modalities fail to monitor tissue temperature in real time with high resolution and accuracy. We investigated a non-invasive optoacoustic method for accurate, real-time monitoring of tissue temperature during thermotherapy. In this study, we induced temperature gradients in tissue and tissue-like samples and monitored the temperature distribution using the optoacoustic technique. The fundamental harmonic of a Q-switched Nd : YAG laser (λ = 1064 nm) was used for optoacoustic wave generation and probing of tissue temperature. The tissue temperature was also monitored with a multi-sensor temperature probe inserted in the samples. Good agreement between optoacoustically measured and actual tissue temperatures was obtained. The accuracy of temperature monitoring was better than 1 0 C, while the spatial resolution was about 1 mm. These data suggest that the optoacoustic technique has the potential to be used for non-invasive, real-time temperature monitoring during thermotherapy

Distributed Arithmetic for Efficient Base-Band Processing in Real-Time GNSS Software Receivers

Directory of Open Access Journals (Sweden)

Grégoire Waelchli

2010-01-01

Full Text Available The growing market of GNSS capable mobile devices is driving the interest of GNSS software solutions, as they can share many system resources (processor, memory, reducing both the size and the cost of their integration. Indeed, with the increasing performance of modern processors, it becomes now feasible to implement in software a multichannel GNSS receiver operating in real time. However, a major issue with this approach is the large computing resources required for the base-band processing, in particular for the correlation operations. Therefore, new algorithms need to be developed in order to reduce the overall complexity of the receiver architecture. Towards that aim, this paper first introduces the challenges of the software implementation of a GPS receiver, with a main focus given to the base-band processing and correlation operations. It then describes the already existing solutions and, from this, introduces a new algorithm based on distributed arithmetic.

Process algebra with timing : real time and discrete time

NARCIS (Netherlands)

Baeten, J.C.M.; Middelburg, C.A.; Bergstra, J.A.; Ponse, A.J.; Smolka, S.A.

2001-01-01

We present real time and discrete time versions of ACP with absolute timing and relative timing. The starting-point is a new real time version with absolute timing, called ACPsat, featuring urgent actions and a delay operator. The discrete time versions are conservative extensions of the discrete

Process algebra with timing: Real time and discrete time

NARCIS (Netherlands)

Baeten, J.C.M.; Middelburg, C.A.

1999-01-01

We present real time and discrete time versions of ACP with absolute timing and relative timing. The startingpoint is a new real time version with absolute timing, called ACPsat , featuring urgent actions and a delay operator. The discrete time versions are conservative extensions of the discrete

Real-Time Trading Strategies of Proactive DISCO with Heterogeneous DG Owners

DEFF Research Database (Denmark)

Zhang, Chunyu; Wang, Qi; Wang, Jianhui

2017-01-01

This paper presents a methodology to obtain the optimal trading strategies between the proactive distribution company (PDISCO), heterogeneous distributed generation owners (DGOs) and wholesale market in a real-time trading framework. In this framework, the PDISCO’s decisions cover the power...... procurements from DGOs and the transactions within the real-time market. A one-leader multi-follower-type bilevel model is proposed to embody the PDISCO-DGO gaming structure. The upper-level (UL) problem is to maximize the PDISCO’s profit, while the lower-level (LL) problem indicates the profit maximization...... the effectiveness and scalability of the proposed model....

Real-time distributed simulation using the Modular Modeling System interfaced to a Bailey NETWORK 90 system

International Nuclear Information System (INIS)

Edwards, R.M.; Turso, J.A.; Garcia, H.E.; Ghie, M.H.; Dharap, S.; Lee, S.

1991-01-01

The Modular Modeling System was adapted for real-time simulation testing of diagnostic expert systems in 1987. The early approach utilized an available general purpose mainframe computer which operated the simulation and diagnostic program in the multitasking environment of the mainframe. That research program was subsequently expanded to intelligent distributed control applications incorporating microprocessor based controllers with the aid of an equipment grant from the National Science Foundation (NSF). The Bailey NETWORK 90 microprocessor-based control system, acquired with the NSF grant, has been operational since April of 1990 and has been interfaced to both VAX mainframe and PC simulations of power plant processes in order to test and demonstrate advanced control and diagnostic concepts. This paper discusses the variety of techniques that have been used and which are under development to interface simulations and other distributed control functions to the Penn State Bailey system

Asymmetric Bimodal Exponential Power Distribution on the Real Line

Directory of Open Access Journals (Sweden)

Mehmet Niyazi Çankaya

2018-01-01

Full Text Available The asymmetric bimodal exponential power (ABEP distribution is an extension of the generalized gamma distribution to the real line via adding two parameters that fit the shape of peakedness in bimodality on the real line. The special values of peakedness parameters of the distribution are a combination of half Laplace and half normal distributions on the real line. The distribution has two parameters fitting the height of bimodality, so capacity of bimodality is enhanced by using these parameters. Adding a skewness parameter is considered to model asymmetry in data. The location-scale form of this distribution is proposed. The Fisher information matrix of these parameters in ABEP is obtained explicitly. Properties of ABEP are examined. Real data examples are given to illustrate the modelling capacity of ABEP. The replicated artificial data from maximum likelihood estimates of parameters of ABEP and other distributions having an algorithm for artificial data generation procedure are provided to test the similarity with real data. A brief simulation study is presented.

Diffusive real-time dynamics of a particle with Berry curvature

Science.gov (United States)

Misaki, Kou; Miyashita, Seiji; Nagaosa, Naoto

2018-02-01

We study theoretically the influence of Berry phase on the real-time dynamics of the single particle focusing on the diffusive dynamics, i.e., the time dependence of the distribution function. Our model can be applied to the real-time dynamics of intraband relaxation and diffusion of optically excited excitons, trions, or particle-hole pair. We found that the dynamics at the early stage is deeply influenced by the Berry curvature in real space (B ), momentum space (Ω ), and also the crossed space between these two (C ). For example, it is found that Ω induces the rotation of the wave packet and causes the time dependence of the mean square displacement of the particle to be linear in time t at the initial stage; it is qualitatively different from the t3 dependence in the absence of the Berry curvature. It is also found that Ω and C modify the characteristic time scale of the thermal equilibration of momentum distribution. Moreover, the dynamics under various combinations of B ,Ω , and C shows singular behaviors such as the critical slowing down or speeding up of the momentum equilibration and the reversals of the direction of rotations. The relevance of our model for time-resolved experiments in transition metal dichalcogenides is also discussed.

Embedded real-time operating system micro kernel design

Science.gov (United States)

Cheng, Xiao-hui; Li, Ming-qiang; Wang, Xin-zheng

2005-12-01

Embedded systems usually require a real-time character. Base on an 8051 microcontroller, an embedded real-time operating system micro kernel is proposed consisting of six parts, including a critical section process, task scheduling, interruption handle, semaphore and message mailbox communication, clock managent and memory managent. Distributed CPU and other resources are among tasks rationally according to the importance and urgency. The design proposed here provides the position, definition, function and principle of micro kernel. The kernel runs on the platform of an ATMEL AT89C51 microcontroller. Simulation results prove that the designed micro kernel is stable and reliable and has quick response while operating in an application system.

Real-time radiography

International Nuclear Information System (INIS)

Bossi, R.H.; Oien, C.T.

1981-01-01

Real-time radiography is used for imaging both dynamic events and static objects. Fluorescent screens play an important role in converting radiation to light, which is then observed directly or intensified and detected. The radiographic parameters for real-time radiography are similar to conventional film radiography with special emphasis on statistics and magnification. Direct-viewing fluoroscopy uses the human eye as a detector of fluorescent screen light or the light from an intensifier. Remote-viewing systems replace the human observer with a television camera. The remote-viewing systems have many advantages over the direct-viewing conditions such as safety, image enhancement, and the capability to produce permanent records. This report reviews real-time imaging system parameters and components

Real-time vision systems

Energy Technology Data Exchange (ETDEWEB)

Johnson, R.; Hernandez, J.E.; Lu, Shin-yee [Lawrence Livermore National Lab., CA (United States)

1994-11-15

Many industrial and defence applications require an ability to make instantaneous decisions based on sensor input of a time varying process. Such systems are referred to as `real-time systems` because they process and act on data as it occurs in time. When a vision sensor is used in a real-time system, the processing demands can be quite substantial, with typical data rates of 10-20 million samples per second. A real-time Machine Vision Laboratory (MVL) was established in FY94 to extend our years of experience in developing computer vision algorithms to include the development and implementation of real-time vision systems. The laboratory is equipped with a variety of hardware components, including Datacube image acquisition and processing boards, a Sun workstation, and several different types of CCD cameras, including monochrome and color area cameras and analog and digital line-scan cameras. The equipment is reconfigurable for prototyping different applications. This facility has been used to support several programs at LLNL, including O Division`s Peacemaker and Deadeye Projects as well as the CRADA with the U.S. Textile Industry, CAFE (Computer Aided Fabric Inspection). To date, we have successfully demonstrated several real-time applications: bullet tracking, stereo tracking and ranging, and web inspection. This work has been documented in the ongoing development of a real-time software library.

Gamma ray observatory dynamics simulator in Ada (GRODY)

International Nuclear Information System (INIS)

1990-09-01

This experiment involved the parallel development of dynamics simulators for the Gamma Ray Observatory in both FORTRAN and Ada for the purpose of evaluating the applicability of Ada to the NASA/Goddard Space Flight Center's flight dynamics environment. The experiment successfully demonstrated that Ada is a viable, valuable technology for use in this environment. In addition to building a simulator, the Ada team evaluated training approaches, developed an Ada methodology appropriate to the flight dynamics environment, and established a baseline for evaluating future Ada projects

Synchronization resources in heterogeneous environments: Time-sharing, real-time and Java

International Nuclear Information System (INIS)

Pereira, A.; Vega, J.; Pacios, L.; Sanchez, E.; Portas, A.

2006-01-01

The asynchronous event distribution system (AEDS) was built to provide synchronization resources within the TJ-II local area network. It is a software system developed to add 'soft synchronization' capabilities to the TJ-II data acquisition, control and analysis environments. 'Soft synchronization' signifies that AEDS is not a real-time system. In fact, AEDS is based on TCP/IP over ETHERNET networks. However, its response time is adequate for practical purposes when synchronization requirements can support some delay between event dispatch and message reception. Event broadcasters (or synchronization servers in AEDS terminology) are Windows computers. Destination computers (or synchronization clients) were also Windows machines in the first version of AEDS. However, this fact imposed a very important limitation on synchronization capabilities. To overcome this situation, synchronization clients for different environments have been added to AEDS: for time-sharing operating systems (Unix and Linux), real-time operating systems (OS-9 and VxWorks) and Java applications. These environments have different synchronization primitives, requiring different approaches to provide the required uniform functionality. This has been achieved with POSIX thread library synchronization primitives (mutex and condition variables) on Unix/Linux systems, IPC mechanisms for concurrent processes on OS-9 and VxWorks real-time operating systems, and 'synchronized-wait/notify' primitives on Java virtual machines

Robust and flexible mapping for real-time distributed applications during the early design phases

DEFF Research Database (Denmark)

Gan, Junhe; Pop, Paul; Gruian, Flavius

2012-01-01

has a high chance of being schedulable, considering the wcet uncertainties, whereas a flexible mapping has a high chance to successfully accommodate the future scenarios. We propose a Genetic Algorithm-based approach to solve this optimization problem. Extensive experiments show the importance......We are interested in mapping hard real-time applications on distributed heterogeneous architectures. An application is modeled as a set of tasks, and we consider a fixed-priority preemptive scheduling policy. We target the early design phases, when decisions have a high impact on the subsequent...... in the functionality requirements are captured using “future scenarios”, which are task sets that model functionality likely to be added in the future. In this context, we derive a mapping of tasks in the application, such that the resulted implementation is both robust and flexible. Robust means that the application...

QUEST/Ada (Query Utility Environment for Software Testing of Ada): The development of a prgram analysis environment for Ada, task 1, phase 2

Science.gov (United States)

Brown, David B.

1990-01-01

The results of research and development efforts are described for Task one, Phase two of a general project entitled The Development of a Program Analysis Environment for Ada. The scope of this task includes the design and development of a prototype system for testing Ada software modules at the unit level. The system is called Query Utility Environment for Software Testing of Ada (QUEST/Ada). The prototype for condition coverage provides a platform that implements expert system interaction with program testing. The expert system can modify data in the instrument source code in order to achieve coverage goals. Given this initial prototype, it is possible to evaluate the rule base in order to develop improved rules for test case generation. The goals of Phase two are the following: (1) to continue to develop and improve the current user interface to support the other goals of this research effort (i.e., those related to improved testing efficiency and increased code reliable); (2) to develop and empirically evaluate a succession of alternative rule bases for the test case generator such that the expert system achieves coverage in a more efficient manner; and (3) to extend the concepts of the current test environment to address the issues of Ada concurrency.

Distributed Algorithms for Time Optimal Reachability Analysis

DEFF Research Database (Denmark)

Zhang, Zhengkui; Nielsen, Brian; Larsen, Kim Guldstrand

2016-01-01

. We propose distributed computing to accelerate time optimal reachability analysis. We develop five distributed state exploration algorithms, implement them in \\uppaal enabling it to exploit the compute resources of a dedicated model-checking cluster. We experimentally evaluate the implemented...... algorithms with four models in terms of their ability to compute near- or proven-optimal solutions, their scalability, time and memory consumption and communication overhead. Our results show that distributed algorithms work much faster than sequential algorithms and have good speedup in general.......Time optimal reachability analysis is a novel model based technique for solving scheduling and planning problems. After modeling them as reachability problems using timed automata, a real-time model checker can compute the fastest trace to the goal states which constitutes a time optimal schedule...

The OPEN-ADAS Approach to Atomic Data Provision

Energy Technology Data Exchange (ETDEWEB)

O' Mullane, M [University of Strathclyde, Department of Physics, Glasgow (United Kingdom)

2011-11-15

Dr O'Mullane of University of Strathclyde presented an overview of the ADAS project (Atomic Data and Analysis Structure, http://www.adas.ac.uk/) and of OPEN-ADAS (http://open.adas.ac.uk/). ADAS is maintained as a self-funding consortium of fusion laboratories. The project provides an interconnected set of computer codes and data collections for modeling the radiating properties of ions and atoms in plasmas. The ADAS data fall into 3 broad classes: 1) Fundamental data such as A- values, cross-sections and effective collision strengths obtained from ADAS collaborators, the literature or data centres. 2) Derived data processed for modeling such as electron temperature and density dependent effective emission coefficients, effective ionization/recombination rates, radiated power and spectral emissivities. 3) Driver data which allow complete regeneration of all ADAS derived data in conjunction with the various ADAS codes. ADAS data uses high quality data as well as baseline data for fall-back when high quality data is not available. The data is mostly embedded in codes and the update without expert help is problematic. The ADAS data formats (adf) are precisely defined and Fortran codes are supplied to read the data sets for easy access. IDL can be used for interactive manipulation. The OPEN-ADAS project is a joint development between the ADAS Project and the IAEA to make the extensive fundamental and derived atomic data for fusion more widely available. It is designed to appeal to both plasma modelers and those interested in the detailed atomic physics. It has been searchable through the Google Scholar and appears in citations, which gives greater visibility and credits to the data producers. The OPEN-ADAS server was replaced due to a series of attacks since June 2011 and was off-line for 8 weeks. The new service removed the registration requirement and hence the user statistics is limited.

The OPEN-ADAS Approach to Atomic Data Provision

International Nuclear Information System (INIS)

O'Mullane, M.

2011-01-01

Dr O'Mullane of University of Strathclyde presented an overview of the ADAS project (Atomic Data and Analysis Structure, http://www.adas.ac.uk/) and of OPEN-ADAS (http://open.adas.ac.uk/). ADAS is maintained as a self-funding consortium of fusion laboratories. The project provides an interconnected set of computer codes and data collections for modeling the radiating properties of ions and atoms in plasmas. The ADAS data fall into 3 broad classes: 1) Fundamental data such as A- values, cross-sections and effective collision strengths obtained from ADAS collaborators, the literature or data centres. 2) Derived data processed for modeling such as electron temperature and density dependent effective emission coefficients, effective ionization/recombination rates, radiated power and spectral emissivities. 3) Driver data which allow complete regeneration of all ADAS derived data in conjunction with the various ADAS codes. ADAS data uses high quality data as well as baseline data for fall-back when high quality data is not available. The data is mostly embedded in codes and the update without expert help is problematic. The ADAS data formats (adf) are precisely defined and Fortran codes are supplied to read the data sets for easy access. IDL can be used for interactive manipulation. The OPEN-ADAS project is a joint development between the ADAS Project and the IAEA to make the extensive fundamental and derived atomic data for fusion more widely available. It is designed to appeal to both plasma modelers and those interested in the detailed atomic physics. It has been searchable through the Google Scholar and appears in citations, which gives greater visibility and credits to the data producers. The OPEN-ADAS server was replaced due to a series of attacks since June 2011 and was off-line for 8 weeks. The new service removed the registration requirement and hence the user statistics is limited.

Ada & the Analytical Engine.

Science.gov (United States)

Freeman, Elisabeth

1996-01-01

Presents a brief history of Ada Byron King, Countess of Lovelace, focusing on her primary role in the development of the Analytical Engine--the world's first computer. Describes the Ada Project (TAP), a centralized World Wide Web site that serves as a clearinghouse for information related to women in computing, and provides a Web address for…

Analysis and Synthesis of Communication-Intensive Heterogeneous Real-Time Systems

DEFF Research Database (Denmark)

Pop, Paul

2003-01-01

Embedded computer systems are now everywhere: from alarm clocks to PDAs, from mobile phones to cars, almost all the devices we use are controlled by embedded computer systems. An important class of embedded computer systems is that of real-time systems, which have to fulfill strict timing...... requirements. As realtime systems become more complex, they are often implemented using distributed heterogeneous architectures. The main objective of this thesis is to develop analysis and synthesis methods for communication-intensive heterogeneous hard real-time systems. The systems are heterogeneous...... is the synthesis of the communication infrastructure, which has a significant impact on the overall system performance and cost. To reduce the time-to-market of products, the design of real-time systems seldom starts from scratch. Typically, designers start from an already existing system, running certain...

Real-time distribution of pelagic fish: combining hydroacoustics, GIS and spatial modelling at a fine spatial scale.

Science.gov (United States)

Muška, Milan; Tušer, Michal; Frouzová, Jaroslava; Mrkvička, Tomáš; Ricard, Daniel; Seďa, Jaromír; Morelli, Federico; Kubečka, Jan

2018-03-29

Understanding spatial distribution of organisms in heterogeneous environment remains one of the chief issues in ecology. Spatial organization of freshwater fish was investigated predominantly on large-scale, neglecting important local conditions and ecological processes. However, small-scale processes are of an essential importance for individual habitat preferences and hence structuring trophic cascades and species coexistence. In this work, we analysed the real-time spatial distribution of pelagic freshwater fish in the Římov Reservoir (Czechia) observed by hydroacoustics in relation to important environmental predictors during 48 hours at 3-h interval. Effect of diurnal cycle was revealed of highest significance in all spatial models with inverse trends between fish distribution and predictors in day and night in general. Our findings highlighted daytime pelagic fish distribution as highly aggregated, with general fish preferences for central, deep and highly illuminated areas, whereas nighttime distribution was more disperse and fish preferred nearshore steep sloped areas with higher depth. This turnover suggests prominent movements of significant part of fish assemblage between pelagic and nearshore areas on a diel basis. In conclusion, hydroacoustics, GIS and spatial modelling proved as valuable tool for predicting local fish distribution and elucidate its drivers, which has far reaching implications for understanding freshwater ecosystem functioning.

ASDEX Upgrade Discharge Control System—A real-time plasma control framework

International Nuclear Information System (INIS)

Treutterer, W.; Cole, R.; Lüddecke, K.; Neu, G.; Rapson, C.; Raupp, G.; Zasche, D.; Zehetbauer, T.

2014-01-01

Highlights: • The ASDEX Upgrade Discharge Control System (DCS) is a comprehensive control system to conduct fusion experiments. • DCS supports real-time diagnostic integration, adaptable feedback schemes, actuator management and exception handling. • DCS offers workflow management, logging and archiving, self-monitoring and inter-process communication. • DCS is based on a distributed, modular software framework architecture designed for real-time operation. • DCS is composed of re-usable generic but highly customisable components. - Abstract: ASDEX Upgrade is a fusion experiment with a size and complexity to allow extrapolation of technical and physical conditions and requirements to devices like ITER and even beyond. In addressing advanced physics topics it makes extensive use of sophisticated real-time control methods. It comprises real-time diagnostic integration, dynamically adaptable multivariable feedback schemes, actuator management including load distribution schemes and a powerful monitoring and pulse supervision concept based on segment scheduling and exception handling. The Discharge Control System (DCS) supplies all this functionality on base of a modular software framework architecture designed for real-time operation. It provides system-wide services like workflow management, logging and archiving, self-monitoring and inter-process communication on Linux, VxWorks and Solaris operating systems. By default DCS supports distributed computing, and a communication layer allows multi-directional signal transfer and data-driven process synchronisation over shared memory as well as over a number of real-time networks. The entire system is built following the same common design concept combining a rich set of re-usable generic but highly customisable components with a configuration-driven component deployment method. We will give an overview on the architectural concepts as well as on the outstanding capabilities of DCS in the domains of inter

ASDEX Upgrade Discharge Control System—A real-time plasma control framework

Energy Technology Data Exchange (ETDEWEB)

Treutterer, W., E-mail: Wolfgang.Treutterer@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, EURATOM Association, Boltzmannstraße 2, 85748 Garching (Germany); Cole, R.; Lüddecke, K. [Unlimited Computer Systems GmbH, Iffeldorf (Germany); Neu, G.; Rapson, C.; Raupp, G.; Zasche, D.; Zehetbauer, T. [Max-Planck-Institut für Plasmaphysik, EURATOM Association, Boltzmannstraße 2, 85748 Garching (Germany)

2014-03-15

Highlights: • The ASDEX Upgrade Discharge Control System (DCS) is a comprehensive control system to conduct fusion experiments. • DCS supports real-time diagnostic integration, adaptable feedback schemes, actuator management and exception handling. • DCS offers workflow management, logging and archiving, self-monitoring and inter-process communication. • DCS is based on a distributed, modular software framework architecture designed for real-time operation. • DCS is composed of re-usable generic but highly customisable components. - Abstract: ASDEX Upgrade is a fusion experiment with a size and complexity to allow extrapolation of technical and physical conditions and requirements to devices like ITER and even beyond. In addressing advanced physics topics it makes extensive use of sophisticated real-time control methods. It comprises real-time diagnostic integration, dynamically adaptable multivariable feedback schemes, actuator management including load distribution schemes and a powerful monitoring and pulse supervision concept based on segment scheduling and exception handling. The Discharge Control System (DCS) supplies all this functionality on base of a modular software framework architecture designed for real-time operation. It provides system-wide services like workflow management, logging and archiving, self-monitoring and inter-process communication on Linux, VxWorks and Solaris operating systems. By default DCS supports distributed computing, and a communication layer allows multi-directional signal transfer and data-driven process synchronisation over shared memory as well as over a number of real-time networks. The entire system is built following the same common design concept combining a rich set of re-usable generic but highly customisable components with a configuration-driven component deployment method. We will give an overview on the architectural concepts as well as on the outstanding capabilities of DCS in the domains of inter

Real-time visualization and quantification of retrograde cardioplegia delivery using near infrared fluorescent imaging.

Science.gov (United States)

Rangaraj, Aravind T; Ghanta, Ravi K; Umakanthan, Ramanan; Soltesz, Edward G; Laurence, Rita G; Fox, John; Cohn, Lawrence H; Bolman, R M; Frangioni, John V; Chen, Frederick Y

2008-01-01

Homogeneous delivery of cardioplegia is essential for myocardial protection during cardiac surgery. Presently, there exist no established methods to quantitatively assess cardioplegia distribution intraoperatively and determine when retrograde cardioplegia is required. In this study, we evaluate the feasibility of near infrared (NIR) imaging for real-time visualization of cardioplegia distribution in a porcine model. A portable, intraoperative, real-time NIR imaging system was utilized. NIR fluorescent cardioplegia solution was developed by incorporating indocyanine green (ICG) into crystalloid cardioplegia solution. Real-time NIR imaging was performed while the fluorescent cardioplegia solution was infused via the retrograde route in five ex vivo normal porcine hearts and in five ex vivo porcine hearts status post left anterior descending (LAD) coronary artery ligation. Horizontal cross-sections of the hearts were obtained at proximal, middle, and distal LAD levels. Videodensitometry was performed to quantify distribution of fluorophore content. The progressive distribution of cardioplegia was clearly visualized with NIR imaging. Complete visualization of retrograde distribution occurred within 4 minutes of infusion. Videodensitometry revealed retrograde cardioplegia, primarily distributed to the left ventricle (LV) and anterior septum. In hearts with LAD ligation, antegrade cardioplegia did not distribute to the anterior LV. This deficiency was compensated for with retrograde cardioplegia supplementation. Incorporation of ICG into cardioplegia allows real-time visualization of cardioplegia delivery via NIR imaging. This technology may prove useful in guiding intraoperative decisions pertaining to when retrograde cardioplegia is mandated.

Memory controllers for real-time embedded systems predictable and composable real-time systems

CERN Document Server

Akesson, Benny

2012-01-01

  Verification of real-time requirements in systems-on-chip becomes more complex as more applications are integrated. Predictable and composable systems can manage the increasing complexity using formal verification and simulation.  This book explains the concepts of predictability and composability and shows how to apply them to the design and analysis of a memory controller, which is a key component in any real-time system. This book is generally intended for readers interested in Systems-on-Chips with real-time applications.   It is especially well-suited for readers looking to use SDRAM memories in systems with hard or firm real-time requirements. There is a strong focus on real-time concepts, such as predictability and composability, as well as a brief discussion about memory controller architectures for high-performance computing. Readers will learn step-by-step how to go from an unpredictable SDRAM memory, offering highly variable bandwidth and latency, to a predictable and composable shared memory...

Real Time Updating in Distributed Urban Rainfall Runoff Modelling

DEFF Research Database (Denmark)

Borup, Morten; Madsen, Henrik

that are being updated from system measurements was studied. The results showed that the fact alone that it takes time for rainfall data to travel the distance between gauges and catchments has such a big negative effect on the forecast skill of updated models, that it can justify the choice of even very...... as in a real data case study. The results confirmed that the method is indeed suitable for DUDMs and that it can be used to utilise upstream as well as downstream water level and flow observations to improve model estimates and forecasts. Due to upper and lower sensor limits many sensors in urban drainage...

Modeling solvation effects in real-space and real-time within density functional approaches

Energy Technology Data Exchange (ETDEWEB)

Delgado, Alain [Istituto Nanoscienze - CNR, Centro S3, via Campi 213/A, 41125 Modena (Italy); Centro de Aplicaciones Tecnológicas y Desarrollo Nuclear, Calle 30 # 502, 11300 La Habana (Cuba); Corni, Stefano; Pittalis, Stefano; Rozzi, Carlo Andrea [Istituto Nanoscienze - CNR, Centro S3, via Campi 213/A, 41125 Modena (Italy)

2015-10-14

The Polarizable Continuum Model (PCM) can be used in conjunction with Density Functional Theory (DFT) and its time-dependent extension (TDDFT) to simulate the electronic and optical properties of molecules and nanoparticles immersed in a dielectric environment, typically liquid solvents. In this contribution, we develop a methodology to account for solvation effects in real-space (and real-time) (TD)DFT calculations. The boundary elements method is used to calculate the solvent reaction potential in terms of the apparent charges that spread over the van der Waals solute surface. In a real-space representation, this potential may exhibit a Coulomb singularity at grid points that are close to the cavity surface. We propose a simple approach to regularize such singularity by using a set of spherical Gaussian functions to distribute the apparent charges. We have implemented the proposed method in the OCTOPUS code and present results for the solvation free energies and solvatochromic shifts for a representative set of organic molecules in water.

Atomic Data and Modelling for Fusion: the ADAS Project

International Nuclear Information System (INIS)

Summers, H. P.; O'Mullane, M. G.

2011-01-01

The paper is an update on the Atomic Data and Analysis Structure, ADAS, since ICAM-DATA06 and a forward look to its evolution in the next five years. ADAS is an international project supporting principally magnetic confinement fusion research. It has participant laboratories throughout the world, including ITER and all its partner countries. In parallel with ADAS, the ADAS-EU Project provides enhanced support for fusion research at Associated Laboratories and Universities in Europe and ITER. OPEN-ADAS, sponsored jointly by the ADAS Project and IAEA, is the mechanism for open access to principal ADAS atomic data classes and facilitating software for their use. EXTENDED-ADAS comprises a variety of special, integrated application software, beyond the purely atomic bounds of ADAS, tuned closely to specific diagnostic analyses and plasma models.The current scientific content and scope of these various ADAS and ADAS related activities are briefly reviewed. These span a number of themes including heavy element spectroscopy and models, charge exchange spectroscopy, beam emission spectroscopy and special features which provide a broad baseline of atomic modelling and support. Emphasis will be placed on 'lifting the fundamental data baseline'--a principal ADAS task for the next few years. This will include discussion of ADAS and ADAS-EU coordinated and shared activities and some of the methods being exploited.

Long-term changes in ADAS-cog: what is clinically relevant for disease modifying trials in Alzheimer?

Science.gov (United States)

Vellas, B; Andrieu, S; Cantet, C; Dartigues, J F; Gauthier, S

2007-01-01

With the development of long-term disease modifying trials, changes in ADAS-Cog at 18 months will rise certainly many questions. We decided to look in the Real.fr study at the links between changes in cognition, ADAS-Cog and function. A total of 346 Alzheimer's patients with ADAS-cog at entry and at 18 months. were eligible for this analysis. These patients were on average 77.44 years old and 254 (72.36%) were women. The great majority lived at home and about 93% were treated with a cholinesterase inhibitor at baseline. Thirty three patients (9%) had a gain of more than 2 points at the ADAS-cog at 18 months (Group I, improvement); 130 (38%) were considered as stable, the reference group (Group II ) characterized by a stability at the ADAS-cog: decline of 2 points to gain of 2 points, 112 subjects (32%) had a moderate decline between 2 and 7 at the ADAScog (Group III) and finally 71 subjects (21%) had a severe impairment more than seven points at the ADAS-cog. A loss of one Basic ADL is certainly highly relevant, and such a change was found at 18 months in more than half of the subjects, which is not surprising for a long-term evolution in mild to moderate AD. An impairment of more than 7 points at the ADAS-cog was found in 21% of the subjects at 18 months and was associated with loss.

49 CFR 37.123 - ADA paratransit eligibility: Standards.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false ADA paratransit eligibility: Standards. 37.123... INDIVIDUALS WITH DISABILITIES (ADA) Paratransit as a Complement to Fixed Route Service § 37.123 ADA... complementary paratransit service shall provide the service to the ADA paratransit eligible individuals...

Scene data fusion: Real-time standoff volumetric gamma-ray imaging

Energy Technology Data Exchange (ETDEWEB)

Barnowski, Ross [Department of Nuclear Engineering, UC Berkeley, 4155 Etcheverry Hall, MC 1730, Berkeley, CA 94720, United States of America (United States); Haefner, Andrew; Mihailescu, Lucian [Lawrence Berkeley National Lab - Applied Nuclear Physics, 1 Cyclotron Road, Berkeley, CA 94720, United States of America (United States); Vetter, Kai [Department of Nuclear Engineering, UC Berkeley, 4155 Etcheverry Hall, MC 1730, Berkeley, CA 94720, United States of America (United States); Lawrence Berkeley National Lab - Applied Nuclear Physics, 1 Cyclotron Road, Berkeley, CA 94720, United States of America (United States)

2015-11-11

An approach to gamma-ray imaging has been developed that enables near real-time volumetric (3D) imaging of unknown environments thus improving the utility of gamma-ray imaging for source-search and radiation mapping applications. The approach, herein dubbed scene data fusion (SDF), is based on integrating mobile radiation imagers with real-time tracking and scene reconstruction algorithms to enable a mobile mode of operation and 3D localization of gamma-ray sources. A 3D model of the scene, provided in real-time by a simultaneous localization and mapping (SLAM) algorithm, is incorporated into the image reconstruction reducing the reconstruction time and improving imaging performance. The SDF concept is demonstrated in this work with a Microsoft Kinect RGB-D sensor, a real-time SLAM solver, and a cart-based Compton imaging platform comprised of two 3D position-sensitive high purity germanium (HPGe) detectors. An iterative algorithm based on Compton kinematics is used to reconstruct the gamma-ray source distribution in all three spatial dimensions. SDF advances the real-world applicability of gamma-ray imaging for many search, mapping, and verification scenarios by improving the tractiblity of the gamma-ray image reconstruction and providing context for the 3D localization of gamma-ray sources within the environment in real-time.

Real-time UV imaging of piroxicam diffusion and distribution from oil solutions into gels mimicking the subcutaneous matrix.

Science.gov (United States)

Ye, Fengbin; Larsen, Susan Weng; Yaghmur, Anan; Jensen, Henrik; Larsen, Claus; Østergaard, Jesper

2012-05-12

A novel real-time UV imaging approach for non-intrusive investigation of the diffusion and partitioning phenomena occurring during piroxicam release from medium chain triglyceride (MCT) solution into two hydrogel matrices is described. Two binary polymer/buffer gel matrices, 0.5% (w/v) agarose and 25% (w/v) Pluronic F127, were applied as simple models mimicking the subcutaneous tissue. The evolution of the absorbance maps as a function of time provided detailed information on the piroxicam release processes upon the exposure of the gel matrices to MCT. Using calibration curves, the concentration maps of piroxicam in the UV imaging area were determined. Regression of the longitudinal concentration-distance profiles, which were obtained using expressions derived from Fick's second law, provided the diffusivity and the distribution coefficients of piroxicam penetrated into the gels. The obtained MCT-agarose (pH 7.4) distribution coefficient of 1.4 was identical to the MCT-aqueous (pH 7.4) distribution coefficient determined by the shake-flask method whereas that of the MCT-Pluronic F127 system was four times less. The experimental data show that UV imaging may have considerable potential for investigating the transport properties of drug formulations intended for the subcutaneous administration. Copyright © 2012 Elsevier B.V. All rights reserved.

GRASP/Ada: Graphical Representations of Algorithms, Structures, and Processes for Ada. The development of a program analysis environment for Ada: Reverse engineering tools for Ada, task 2, phase 3

Science.gov (United States)

Cross, James H., II

1991-01-01

The main objective is the investigation, formulation, and generation of graphical representations of algorithms, structures, and processes for Ada (GRASP/Ada). The presented task, in which various graphical representations that can be extracted or generated from source code are described and categorized, is focused on reverse engineering. The following subject areas are covered: the system model; control structure diagram generator; object oriented design diagram generator; user interface; and the GRASP library.

High performance real-time flight simulation at NASA Langley

Science.gov (United States)

Cleveland, Jeff I., II

1994-01-01

In order to meet the stringent time-critical requirements for real-time man-in-the-loop flight simulation, computer processing operations must be deterministic and be completed in as short a time as possible. This includes simulation mathematical model computational and data input/output to the simulators. In 1986, in response to increased demands for flight simulation performance, personnel at NASA's Langley Research Center (LaRC), working with the contractor, developed extensions to a standard input/output system to provide for high bandwidth, low latency data acquisition and distribution. The Computer Automated Measurement and Control technology (IEEE standard 595) was extended to meet the performance requirements for real-time simulation. This technology extension increased the effective bandwidth by a factor of ten and increased the performance of modules necessary for simulator communications. This technology is being used by more than 80 leading technological developers in the United States, Canada, and Europe. Included among the commercial applications of this technology are nuclear process control, power grid analysis, process monitoring, real-time simulation, and radar data acquisition. Personnel at LaRC have completed the development of the use of supercomputers for simulation mathematical model computational to support real-time flight simulation. This includes the development of a real-time operating system and the development of specialized software and hardware for the CAMAC simulator network. This work, coupled with the use of an open systems software architecture, has advanced the state of the art in real time flight simulation. The data acquisition technology innovation and experience with recent developments in this technology are described.

Ada and the rapid development lifecycle

Science.gov (United States)

Deforrest, Lloyd; Gref, Lynn

1991-01-01

JPL is under contract, through NASA, with the US Army to develop a state-of-the-art Command Center System for the US European Command (USEUCOM). The Command Center System will receive, process, and integrate force status information from various sources and provide this integrated information to staff officers and decision makers in a format designed to enhance user comprehension and utility. The system is based on distributed workstation class microcomputers, VAX- and SUN-based data servers, and interfaces to existing military mainframe systems and communication networks. JPL is developing the Command Center System utilizing an incremental delivery methodology called the Rapid Development Methodology with adherence to government and industry standards including the UNIX operating system, X Windows, OSF/Motif, and the Ada programming language. Through a combination of software engineering techniques specific to the Ada programming language and the Rapid Development Approach, JPL was able to deliver capability to the military user incrementally, with comparable quality and improved economies of projects developed under more traditional software intensive system implementation methodologies.

Patterns for automatic generation of soft real-time system models

NARCIS (Netherlands)

Florescu, O.; Voeten, J.P.M.; Theelen, B.D.; Corporaal, H.

2009-01-01

Worst-case assumptions about the timing of systems are often too conservative when analyzing distributed soft real-time systems as they lead to over-dimensioned and expensive products. For these systems, a certain percentage of deadline misses is often affordable. Instead of a binary answer

Advanced Map For Real-Time Process Control

Science.gov (United States)

Shiobara, Yasuhisa; Matsudaira, Takayuki; Sashida, Yoshio; Chikuma, Makoto

1987-10-01

MAP, a communications protocol for factory automation proposed by General Motors [1], has been accepted by users throughout the world and is rapidly becoming a user standard. In fact, it is now a LAN standard for factory automation. MAP is intended to interconnect different devices, such as computers and programmable devices, made by different manufacturers, enabling them to exchange information. It is based on the OSI intercomputer com-munications protocol standard under development by the ISO. With progress and standardization, MAP is being investigated for application to process control fields other than factory automation [2]. The transmission response time of the network system and centralized management of data exchanged with various devices for distributed control are import-ant in the case of a real-time process control with programmable controllers, computers, and instruments connected to a LAN system. MAP/EPA and MINI MAP aim at reduced overhead in protocol processing and enhanced transmission response. If applied to real-time process control, a protocol based on point-to-point and request-response transactions limits throughput and transmission response. This paper describes an advanced MAP LAN system applied to real-time process control by adding a new data transmission control that performs multicasting communication voluntarily and periodically in the priority order of data to be exchanged.

A Custom Data Logger for Real-Time Remote Field Data Collections

Science.gov (United States)

2017-03-01

a Linux PC giving a remote user complete control of the data logger, its file system , and its programs. Additionally, while operating the datalogger...ERDC/CHL CHETN-VI-46 March 2017 Approved for public release; distribution is unlimited. A Custom Data Logger for Real - Time Remote Field Data...Field Research Facility (FRF), for remote real - time data collections. This custom data logger is compact and energy efficient but has the same

49 CFR 37.125 - ADA paratransit eligibility: Process.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false ADA paratransit eligibility: Process. 37.125... INDIVIDUALS WITH DISABILITIES (ADA) Paratransit as a Complement to Fixed Route Service § 37.125 ADA... § 37.121 of this part shall establish a process for determining ADA paratransit eligibility. (a) The...

Verifying Real-Time Systems using Explicit-time Description Methods

Directory of Open Access Journals (Sweden)

Hao Wang

2009-12-01

Full Text Available Timed model checking has been extensively researched in recent years. Many new formalisms with time extensions and tools based on them have been presented. On the other hand, Explicit-Time Description Methods aim to verify real-time systems with general untimed model checkers. Lamport presented an explicit-time description method using a clock-ticking process (Tick to simulate the passage of time together with a group of global variables for time requirements. This paper proposes a new explicit-time description method with no reliance on global variables. Instead, it uses rendezvous synchronization steps between the Tick process and each system process to simulate time. This new method achieves better modularity and facilitates usage of more complex timing constraints. The two explicit-time description methods are implemented in DIVINE, a well-known distributed-memory model checker. Preliminary experiment results show that our new method, with better modularity, is comparable to Lamport's method with respect to time and memory efficiency.

Essays in real-time forecasting

OpenAIRE

Liebermann, Joelle

2012-01-01

This thesis contains three essays in the field of real-time econometrics, and more particularlyforecasting.The issue of using data as available in real-time to forecasters, policymakers or financialmarkets is an important one which has only recently been taken on board in the empiricalliterature. Data available and used in real-time are preliminary and differ from ex-postrevised data, and given that data revisions may be quite substantial, the use of latestavailable instead of real-time can s...

OLDER DRIVERS AND ADAS

Directory of Open Access Journals (Sweden)

Ragnhild J. DAVIDSE

2006-01-01

Next, based on the available literature, relevant ADAS are discussed in terms of their availability, their effects on safety and the willingness of older drivers to use and buy them. One of the conclusions is that only very few of the types of support that are thought to be most beneficial to the safety of older drivers are provided by the ADAS that are currently available.

Real-time frequency-to-time mapping based on spectrally-discrete chromatic dispersion.

Science.gov (United States)

Dai, Yitang; Li, Jilong; Zhang, Ziping; Yin, Feifei; Li, Wangzhe; Xu, Kun

2017-07-10

Traditional photonics-assisted real-time Fourier transform (RTFT) usually suffers from limited chromatic dispersion, huge volume, or large time delay and attendant loss. In this paper we propose frequency-to-time mapping (FTM) by spectrally-discrete dispersion to increase frequency sensitivity greatly. The novel media has periodic ON/OFF intensity frequency response while quadratic phase distribution along disconnected channels, which de-chirps matched optical input to repeated Fourier-transform-limited output. Real-time FTM is then obtained within each period. Since only discrete phase retardation rather than continuously-changed true time delay is required, huge equivalent dispersion is then available by compact device. Such FTM is theoretically analyzed, and implementation by cascaded optical ring resonators is proposed. After a numerical example, our theory is demonstrated by a proof-of-concept experiment, where a single loop containing 0.5-meters-long fiber is used. FTM under 400-MHz unambiguous bandwidth and 25-MHz resolution is reported. Highly-sensitive and linear mapping is achieved with 6.25 ps/MHz, equivalent to ~4.6 × 10 4 -km standard single mode fiber. Extended instantaneous bandwidth is expected by ring cascading. Our proposal may provide a promising method for real-time, low-latency Fourier transform.

Tool set for distributed real-time machine control

Science.gov (United States)

Carrott, Andrew J.; Wright, Christopher D.; West, Andrew A.; Harrison, Robert; Weston, Richard H.

1997-01-01

Demands for increased control capabilities require next generation manufacturing machines to comprise intelligent building elements, physically located at the point where the control functionality is required. Networks of modular intelligent controllers are increasingly designed into manufacturing machines and usable standards are slowly emerging. To implement a control system using off-the-shelf intelligent devices from multi-vendor sources requires a number of well defined activities, including (a) the specification and selection of interoperable control system components, (b) device independent application programming and (c) device configuration, management, monitoring and control. This paper briefly discusses the support for the above machine lifecycle activities through the development of an integrated computing environment populated with an extendable software toolset. The toolset supports machine builder activities such as initial control logic specification, logic analysis, machine modeling, mechanical verification, application programming, automatic code generation, simulation/test, version control, distributed run-time support and documentation. The environment itself consists of system management tools and a distributed object-oriented database which provides storage for the outputs from machine lifecycle activities and specific target control solutions.

AN ADA NAMELIST PACKAGE

Science.gov (United States)

Klumpp, A. R.

1994-01-01

The Ada Namelist Package, developed for the Ada programming language, enables a calling program to read and write FORTRAN-style namelist files. A namelist file consists of any number of assignment statements in any order. Features of the Ada Namelist Package are: the handling of any combination of user-defined types; the ability to read vectors, matrices, and slices of vectors and matrices; the handling of mismatches between variables in the namelist file and those in the programmed list of namelist variables; and the ability to avoid searching the entire input file for each variable. The principle user benefits of this software are the following: the ability to write namelist-readable files, the ability to detect most file errors in the initialization phase, a package organization that reduces the number of instantiated units to a few packages rather than to many subprograms, a reduced number of restrictions, and an increased execution speed. The Ada Namelist reads data from an input file into variables declared within a user program. It then writes data from the user program to an output file, printer, or display. The input file contains a sequence of assignment statements in arbitrary order. The output is in namelist-readable form. There is a one-to-one correspondence between namelist I/O statements executed in the user program and variables read or written. Nevertheless, in the input file, mismatches are allowed between assignment statements in the file and the namelist read procedure statements in the user program. The Ada Namelist Package itself is non-generic. However, it has a group of nested generic packages following the nongeneric opening portion. The opening portion declares a variety of useraccessible constants, variables and subprograms. The subprograms are procedures for initializing namelists for reading, reading and writing strings. The subprograms are also functions for analyzing the content of the current dataset and diagnosing errors. Two nested

Synchronization resources in heterogeneous environments: Time-sharing, real-time and Java

Energy Technology Data Exchange (ETDEWEB)

Pereira, A. [Asociacion EURATOM/CIEMAT para Fusion, CIEMAT Edificio 66, Avda. Complutense, 22, 28040 Madrid (Spain)]. E-mail: augusto.pereira@ciemat.es; Vega, J. [Asociacion EURATOM/CIEMAT para Fusion, CIEMAT Edificio 66, Avda. Complutense, 22, 28040 Madrid (Spain); Pacios, L. [Asociacion EURATOM/CIEMAT para Fusion, CIEMAT Edificio 66, Avda. Complutense, 22, 28040 Madrid (Spain); Sanchez, E. [Asociacion EURATOM/CIEMAT para Fusion, CIEMAT Edificio 66, Avda. Complutense, 22, 28040 Madrid (Spain); Portas, A. [Asociacion EURATOM/CIEMAT para Fusion, CIEMAT Edificio 66, Avda. Complutense, 22, 28040 Madrid (Spain)

2006-07-15

The asynchronous event distribution system (AEDS) was built to provide synchronization resources within the TJ-II local area network. It is a software system developed to add 'soft synchronization' capabilities to the TJ-II data acquisition, control and analysis environments. 'Soft synchronization' signifies that AEDS is not a real-time system. In fact, AEDS is based on TCP/IP over ETHERNET networks. However, its response time is adequate for practical purposes when synchronization requirements can support some delay between event dispatch and message reception. Event broadcasters (or synchronization servers in AEDS terminology) are Windows computers. Destination computers (or synchronization clients) were also Windows machines in the first version of AEDS. However, this fact imposed a very important limitation on synchronization capabilities. To overcome this situation, synchronization clients for different environments have been added to AEDS: for time-sharing operating systems (Unix and Linux), real-time operating systems (OS-9 and VxWorks) and Java applications. These environments have different synchronization primitives, requiring different approaches to provide the required uniform functionality. This has been achieved with POSIX thread library synchronization primitives (mutex and condition variables) on Unix/Linux systems, IPC mechanisms for concurrent processes on OS-9 and VxWorks real-time operating systems, and 'synchronized-wait/notify' primitives on Java virtual machines.

Integration of real-time mapping technology in disaster relief distribution.

Science.gov (United States)

2013-02-01

Vehicle routing for disaster relief distribution involves many challenges that distinguish this problem from those in commercial settings, given the time sensitive and resource constrained nature of relief activities. While operations research approa...

New scoring methodology improves the sensitivity of the Alzheimer's Disease Assessment Scale-Cognitive subscale (ADAS-Cog) in clinical trials.

Science.gov (United States)

Verma, Nishant; Beretvas, S Natasha; Pascual, Belen; Masdeu, Joseph C; Markey, Mia K

2015-11-12

As currently used, the Alzheimer's Disease Assessment Scale-Cognitive subscale (ADAS-Cog) has low sensitivity for measuring Alzheimer's disease progression in clinical trials. A major reason behind the low sensitivity is its sub-optimal scoring methodology, which can be improved to obtain better sensitivity. Using item response theory, we developed a new scoring methodology (ADAS-CogIRT) for the ADAS-Cog, which addresses several major limitations of the current scoring methodology. The sensitivity of the ADAS-CogIRT methodology was evaluated using clinical trial simulations as well as a negative clinical trial, which had shown an evidence of a treatment effect. The ADAS-Cog was found to measure impairment in three cognitive domains of memory, language, and praxis. The ADAS-CogIRT methodology required significantly fewer patients and shorter trial durations as compared to the current scoring methodology when both were evaluated in simulated clinical trials. When validated on data from a real clinical trial, the ADAS-CogIRT methodology had higher sensitivity than the current scoring methodology in detecting the treatment effect. The proposed scoring methodology significantly improves the sensitivity of the ADAS-Cog in measuring progression of cognitive impairment in clinical trials focused in the mild-to-moderate Alzheimer's disease stage. This provides a boost to the efficiency of clinical trials requiring fewer patients and shorter durations for investigating disease-modifying treatments.

Tokamak equilibrium reconstruction code LIUQE and its real time implementation

International Nuclear Information System (INIS)

Moret, J.-M.; Duval, B.P.; Le, H.B.; Coda, S.; Felici, F.; Reimerdes, H.

2015-01-01

Highlights: • Algorithm vertical stabilisation using a linear parametrisation of the current density. • Experimentally derived model of the vacuum vessel to account for vessel currents. • Real-time contouring algorithm for flux surface averaged 1.5 D transport equations. • Full real time implementation coded in SIMULINK runs in less than 200 μs. • Applications: shape control, safety factor profile control, coupling with RAPTOR. - Abstract: Equilibrium reconstruction consists in identifying, from experimental measurements, a distribution of the plasma current density that satisfies the pressure balance constraint. The LIUQE code adopts a computationally efficient method to solve this problem, based on an iterative solution of the Poisson equation coupled with a linear parametrisation of the plasma current density. This algorithm is unstable against vertical gross motion of the plasma column for elongated shapes and its application to highly shaped plasmas on TCV requires a particular treatment of this instability. TCV's continuous vacuum vessel has a low resistance designed to enhance passive stabilisation of the vertical position. The eddy currents in the vacuum vessel have a sizeable influence on the equilibrium reconstruction and must be taken into account. A real time version of LIUQE has been implemented on TCV's distributed digital control system with a cycle time shorter than 200 μs for a full spatial grid of 28 by 65, using all 133 experimental measurements and including the flux surface average of quantities necessary for the real time solution of 1.5 D transport equations. This performance was achieved through a thoughtful choice of numerical methods and code optimisation techniques at every step of the algorithm, and was coded in MATLAB and SIMULINK for the off-line and real time version respectively

Ovation Prime Real-Time

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Ovation Prime Real-Time (OPRT) product is a real-time forecast and nowcast model of auroral power and is an operational implementation of the work by Newell et...

Parallel Ada benchmarks for the SVMS

Science.gov (United States)

Collard, Philippe E.

1990-01-01

The use of parallel processing paradigm to design and develop faster and more reliable computers appear to clearly mark the future of information processing. NASA started the development of such an architecture: the Spaceborne VHSIC Multi-processor System (SVMS). Ada will be one of the languages used to program the SVMS. One of the unique characteristics of Ada is that it supports parallel processing at the language level through the tasking constructs. It is important for the SVMS project team to assess how efficiently the SVMS architecture will be implemented, as well as how efficiently Ada environment will be ported to the SVMS. AUTOCLASS II, a Bayesian classifier written in Common Lisp, was selected as one of the benchmarks for SVMS configurations. The purpose of the R and D effort was to provide the SVMS project team with the version of AUTOCLASS II, written in Ada, that would make use of Ada tasking constructs as much as possible so as to constitute a suitable benchmark. Additionally, a set of programs was developed that would measure Ada tasking efficiency on parallel architectures as well as determine the critical parameters influencing tasking efficiency. All this was designed to provide the SVMS project team with a set of suitable tools in the development of the SVMS architecture.

Real-Time Tomography of Gas-Jets with a Wollaston Interferometer

Directory of Open Access Journals (Sweden)

Andreas Adelmann

2018-03-01

Full Text Available A tomographic gas-density diagnostic using a Single-Beam Wollaston Interferometer able to characterize non-symmetric density distributions in gas jets is presented. A real-time tomographic algorithm is able to reconstruct three-dimensional density distributions. A Maximum Likelihood-Expectation Maximization algorithm, an iterative method with good convergence properties compared to simple back projection, is used. With the use of graphical processing units, real-time computation and high resolution are achieved. Two different gas jets are characterized: a kHz, piezo-driven jet for lower densities and a solenoid valve-based jet producing higher densities. While the first jet is used for free electron laser photon beam characterization, the second jet is used in laser wake field acceleration experiments. In this latter application, well-tailored and non-symmetric density distributions produced by a supersonic shock front generated by a razor blade inserted laterally to the gas flow, which breaks cylindrical symmetry, need to be characterized.

A Model for Real-Time Data Reputation Via Cyber Telemetry

Science.gov (United States)

2016-06-01

methodology which focuses on iterative cycles, known as sprints, to produce the capabilities of the system. Traditional waterfall models do not allow for...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release; distribution is unlimited A MODEL FOR REAL...Master’s Thesis 4. TITLE AND SUBTITLE A MODEL FOR REAL-TIME DATA REPUTATION VIA CYBER TELEMETRY 5. FUNDING NUMBERS 6. AUTHOR(S) Beau M

QUEST/Ada: Query utility environment for software testing of Ada

Science.gov (United States)

Brown, David B.

1989-01-01

Results of research and development efforts are presented for Task 1, Phase 2 of a general project entitled, The Development of a Program Analysis Environment for Ada. A prototype of the QUEST/Ada system was developed to collect data to determine the effectiveness of the rule-based testing paradigm. The prototype consists of five parts: the test data generator, the parser/scanner, the test coverage analyzer, a symbolic evaluator, and a data management facility, known as the Librarian. These components are discussed at length. Also presented is an experimental design for the evaluations, an overview of the project, and a schedule for its completion.

Sci—Thur PM: Planning and Delivery — 06: Real-Time Interactive Treatment Planning

International Nuclear Information System (INIS)

Matthews, Q; Mestrovic, A; Otto, K

2014-01-01

Purpose: To describe and evaluate a novel system for generalized Real-Time Interactive Planning (RTIP) applied to head and neck (H and N) VMAT. Methods: The clinician interactively manipulates dose distributions using DVHs, isodoses, or rate of dose fall-off, which may be subjected to user-defined constraints. Dose is calculated using a fast Achievable Dose Estimate (ADE) algorithm, which simulates the limits of what can be achieved during treatment. After each manipulation contributing fluence elements are modified and the dose distribution updates in effectively real-time. For H and N VMAT planning, structure sets for 11 patients were imported into RTIP. Each dose distribution was interactively modified to minimize OAR dose while constraining target DVHs. The resulting RTIP DVHs were transferred to the Eclipse™ VMAT optimizer, and conventional VMAT optimization was performed. Results: Dose calculation and update times for the ADE algorithm ranged from 2.4 to 22.6 milliseconds, thus facilitating effectively real-time manipulation of dose distributions. For each of the 11 H and N VMAT cases, the RTIP process took ∼2–10 minutes. All RTIP plans exhibited acceptable PTV coverage, mean dose, and max dose. 10 of 11 RTIP plans achieved substantially improved sparing of one or more OARs without compromising dose to targets or other OARs. Importantly, 10 of the 11 RTIP plans required only one or two post-RTIP optimizations. Conclusions: RTIP is a novel system for manipulating and updating achievable dose distributions in real-time. H and N VMAT plans generated using RTIP demonstrate improved OAR sparing and planning efficiency. Disclosures: One author has a commercial interest in the presented materials

GRODY - GAMMA RAY OBSERVATORY DYNAMICS SIMULATOR IN ADA

Science.gov (United States)

Stark, M.

1994-01-01

analyst can send results output in graphical or tabular form to a terminal, disk, or hardcopy device, and can choose to have any or all items plotted against time or against each other. Goddard researchers developed GRODY on a VAX 8600 running VMS version 4.0. For near real time performance, GRODY requires a VAX at least as powerful as a model 8600 running VMS 4.0 or a later version. To use GRODY, the VAX needs an Ada Compilation System (ACS), Code Management System (CMS), and 1200K memory. GRODY is written in Ada and FORTRAN.

Real-time three-dimensional color Doppler echocardiography for characterizing the spatial velocity distribution and quantifying the peak flow rate in the left ventricular outflow tract

Science.gov (United States)

Tsujino, H.; Jones, M.; Shiota, T.; Qin, J. X.; Greenberg, N. L.; Cardon, L. A.; Morehead, A. J.; Zetts, A. D.; Travaglini, A.; Bauer, F.;

A GPS-based Real-time Road Traffic Monitoring System

Science.gov (United States)

Tanti, Kamal Kumar

In recent years, monitoring systems are astonishingly inclined towards ever more automatic; reliably interconnected, distributed and autonomous operation. Specifically, the measurement, logging, data processing and interpretation activities may be carried out by separate units at different locations in near real-time. The recent evolution of mobile communication devices and communication technologies has fostered a growing interest in the GIS & GPS-based location-aware systems and services. This paper describes a real-time road traffic monitoring system based on integrated mobile field devices (GPS/GSM/IOs) working in tandem with advanced GIS-based application software providing on-the-fly authentications for real-time monitoring and security enhancement. The described system is developed as a fully automated, continuous, real-time monitoring system that employs GPS sensors and Ethernet and/or serial port communication techniques are used to transfer data between GPS receivers at target points and a central processing computer. The data can be processed locally or remotely based on the requirements of client’s satisfaction. Due to the modular architecture of the system, other sensor types may be supported with minimal effort. Data on the distributed network & measurements are transmitted via cellular SIM cards to a Control Unit, which provides for post-processing and network management. The Control Unit may be remotely accessed via an Internet connection. The new system will not only provide more consistent data about the road traffic conditions but also will provide methods for integrating with other Intelligent Transportation Systems (ITS). For communication between the mobile device and central monitoring service GSM technology is used. The resulting system is characterized by autonomy, reliability and a high degree of automation.

Stress Analysis and Fatigue Behaviour of PTFE-Bronze Layered Journal Bearing under Real-Time Dynamic Loading

Science.gov (United States)

Duman, M. S.; Kaplan, E.; Cuvalcı, O.

2018-01-01

The present paper is based on experimental studies and numerical simulations on the surface fatigue failure of the PTFE-bronze layered journal bearings under real-time loading. ‘Permaglide Plain Bearings P10’ type journal bearings were experimentally tested under different real time dynamic loadings by using real time journal bearing test system in our laboratory. The journal bearing consists of a PTFE-bronze layer approximately 0.32 mm thick on the steel support layer with 2.18 mm thick. Two different approaches have been considered with in experiments: (i) under real- time constant loading with varying bearing widths, (ii) under different real-time loadings at constant bearing widths. Fatigue regions, micro-crack dispersion and stress distributions occurred at the journal bearing were experimentally and theoretically investigated. The relation between fatigue region and pressure distributions were investigated by determining the circumferential pressure distribution under real-time dynamic loadings for the position of every 10° crank angles. In the theoretical part; stress and deformation distributions at the surface of the journal bearing analysed by using finite element methods to determine the relationship between stress and fatigue behaviour. As a result of this study, the maximum oil pressure and fatigue cracks were observed in the most heavily loaded regions of the bearing surface. Experimental results show that PTFE-Bronze layered journal bearings fatigue behaviour is better than the bearings include white metal alloy.

Alternative majority-voting methods for real-time computing systems

Science.gov (United States)

Shin, Kang G.; Dolter, James W.

1989-01-01

Two techniques that provide a compromise between the high time overhead in maintaining synchronous voting and the difficulty of combining results in asynchronous voting are proposed. These techniques are specifically suited for real-time applications with a single-source/single-sink structure that need instantaneous error masking. They provide a compromise between a tightly synchronized system in which the synchronization overhead can be quite high, and an asynchronous system which lacks suitable algorithms for combining the output data. Both quorum-majority voting (QMV) and compare-majority voting (CMV) are most applicable to distributed real-time systems with single-source/single-sink tasks. All real-time systems eventually have to resolve their outputs into a single action at some stage. The development of the advanced information processing system (AIPS) and other similar systems serve to emphasize the importance of these techniques. Time bounds suggest that it is possible to reduce the overhead for quorum-majority voting to below that for synchronous voting. All the bounds assume that the computation phase is nonpreemptive and that there is no multitasking.

ISTTOK real-time architecture

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Ivo S., E-mail: ivoc@ipfn.ist.utl.pt; Duarte, Paulo; Fernandes, Horácio; Valcárcel, Daniel F.; Carvalho, Pedro J.; Silva, Carlos; Duarte, André S.; Neto, André; Sousa, Jorge; Batista, António J.N.; Hekkert, Tiago; Carvalho, Bernardo B.

2014-03-15

Highlights: • All real-time diagnostics and actuators were integrated in the same control platform. • A 100 μs control cycle was achieved under the MARTe framework. • Time-windows based control with several event-driven control strategies implemented. • AC discharges with exception handling on iron core flux saturation. • An HTML discharge configuration was developed for configuring the MARTe system. - Abstract: The ISTTOK tokamak was upgraded with a plasma control system based on the Advanced Telecommunications Computing Architecture (ATCA) standard. This control system was designed to improve the discharge stability and to extend the operational space to the alternate plasma current (AC) discharges as part of the ISTTOK scientific program. In order to accomplish these objectives all ISTTOK diagnostics and actuators relevant for real-time operation were integrated in the control system. The control system was programmed in C++ over the Multi-threaded Application Real-Time executor (MARTe) which provides, among other features, a real-time scheduler, an interrupt handler, an intercommunications interface between code blocks and a clearly bounded interface with the external devices. As a complement to the MARTe framework, the BaseLib2 library provides the foundations for the data, code introspection and also a Hypertext Transfer Protocol (HTTP) server service. Taking advantage of the modular nature of MARTe, the algorithms of each diagnostic data processing, discharge timing, context switch, control and actuators output reference generation, run on well-defined blocks of code named Generic Application Module (GAM). This approach allows reusability of the code, simplified simulation, replacement or editing without changing the remaining GAMs. The ISTTOK control system GAMs run sequentially each 100 μs cycle on an Intel{sup ®} Q8200 4-core processor running at 2.33 GHz located in the ATCA crate. Two boards (inside the ATCA crate) with 32 analog

ISTTOK real-time architecture

International Nuclear Information System (INIS)

Carvalho, Ivo S.; Duarte, Paulo; Fernandes, Horácio; Valcárcel, Daniel F.; Carvalho, Pedro J.; Silva, Carlos; Duarte, André S.; Neto, André; Sousa, Jorge; Batista, António J.N.; Hekkert, Tiago; Carvalho, Bernardo B.

2014-01-01

Highlights: • All real-time diagnostics and actuators were integrated in the same control platform. • A 100 μs control cycle was achieved under the MARTe framework. • Time-windows based control with several event-driven control strategies implemented. • AC discharges with exception handling on iron core flux saturation. • An HTML discharge configuration was developed for configuring the MARTe system. - Abstract: The ISTTOK tokamak was upgraded with a plasma control system based on the Advanced Telecommunications Computing Architecture (ATCA) standard. This control system was designed to improve the discharge stability and to extend the operational space to the alternate plasma current (AC) discharges as part of the ISTTOK scientific program. In order to accomplish these objectives all ISTTOK diagnostics and actuators relevant for real-time operation were integrated in the control system. The control system was programmed in C++ over the Multi-threaded Application Real-Time executor (MARTe) which provides, among other features, a real-time scheduler, an interrupt handler, an intercommunications interface between code blocks and a clearly bounded interface with the external devices. As a complement to the MARTe framework, the BaseLib2 library provides the foundations for the data, code introspection and also a Hypertext Transfer Protocol (HTTP) server service. Taking advantage of the modular nature of MARTe, the algorithms of each diagnostic data processing, discharge timing, context switch, control and actuators output reference generation, run on well-defined blocks of code named Generic Application Module (GAM). This approach allows reusability of the code, simplified simulation, replacement or editing without changing the remaining GAMs. The ISTTOK control system GAMs run sequentially each 100 μs cycle on an Intel ® Q8200 4-core processor running at 2.33 GHz located in the ATCA crate. Two boards (inside the ATCA crate) with 32 analog

Real-time simulation of ex-core nuclear instrumentation system

International Nuclear Information System (INIS)

Zhao Qiang; Zhang Zhijian; Cao Xinrong

2005-01-01

Real-time simulation of ex-core nuclear instrumentation system is an indispensable part of nuclear power plant (NPP) full-scope training simulator. The simulation method, which is based upon the theory of measurement, is introduced in the paper. The fitting formula between the measured data and the three-dimensional neutron flux distribution in the core is established. The fitting parameter is adjusted according to the reactor physical calculation or the experiment of power calibration. The simulation result shows that the method can simulate the ex-core neutron instrumentation system accurately in real-time and meets the needs of NPP full-scope training simulator. (authors)

Distributed Real-Time Embedded Video Processing

National Research Council Canada - National Science Library

Lv, Tiehan

2004-01-01

.... A deployable multi-camera video system must perform distributed computation, including computation near the camera as well as remote computations, in order to meet performance and power requirements...

Real-time system for processing regime diagnostic on accelerator

International Nuclear Information System (INIS)

Yeran, L.V.; Karasyov, S.P.; Uvarov, V.L.; Shlyakhov, I.N.

2004-01-01

The automatic real-time system operating at the LU-10 linac and providing measurements of the parameters such as the beam current (average and pulse values), the electron energy, the linear density distribution of beam current, and also the conveyor speed is described in the paper

Real-time adjustment of pressure to demand in water distribution systems: Parameter-less P-controller algorithm

CSIR Research Space (South Africa)

Page, Philip R

2016-08-01

Full Text Available Remote real-time control is currently the most advanced form of pressure management. Here the parameters describing pressure control valves (or pumps) are changed in real-time in such a way to provide the most optimal pressure in the water...

Restoring balance to B cells in ADA deficiency.

Science.gov (United States)

Luning Prak, Eline T

2012-06-01

It is paradoxical that immunodeficiency disorders are associated with autoimmunity. Adenosine deaminase (ADA) deficiency, a cause of X-linked severe combined immunodeficiency (SCID), is a case in point. In this issue of the JCI, Sauer and colleagues investigate the B cell defects in ADA-deficient patients. They demonstrate that ADA patients receiving enzyme replacement therapy had B cell tolerance checkpoint defects. Remarkably, gene therapy with a retrovirus that expresses ADA resulted in the apparent correction of these defects, with normalization of peripheral B cell autoantibody frequencies. In vitro, agents that either block ADA or overexpress adenosine resulted in altered B cell receptor and TLR signaling. Collectively, these data implicate a B cell-intrinsic mechanism for alterations in B cell tolerance in the setting of partial ADA deficiency that is corrected by gene therapy.

ADA members weigh in on critical issues.

Science.gov (United States)

Burgess, Karen; Ruesch, Jon D; Mikkelsen, Matthew C; Wagner, Karen Schaid

2003-01-01

Science, new technology, patient care, dental reimbursement and government regulations all affect today's dental practitioners. To find out more about how such challenges may affect current private practitioners, the American Dental Association conducted the 2000 Membership Needs and Opinions Survey. A questionnaire was sent to 6,310 ADA members in January 2000 with follow-up mailings in February, March and April 2000. Data collection was completed in July 2000. The survey included questions on critical professional issues, and on perceptions of the ADA and ADA priorities. A total of 3,558 completed surveys were received for an adjusted response rate of 59.5 percent. Members rated the identified issues' level of importance to them. The top three issues included "maintaining my ability to recommend the treatment option I feel is most appropriate for my patients," "receiving fair reimbursement for the dental services I provide," and "protecting myself, my staff and my patients from communicable diseases." New dentists found other items to be more significant to them compared with members overall. Although ADA members as a whole had similar views on critical issues facing dentistry and ADA priorities, there were significant differences regarding some issues. New dentists were far more concerned about securing funds for their practice and paying off debt than were all ADA members. Minority dentists expressed greater levels of concern about certain issues than did all ADA members. When planning and implementing ADA activities, the Association should continue to take into account members' relative rankings of professional issues and note issues of special interest to selected membership subgroups.

Architecture for dynamically reconfigurable real-time lossless compression

Science.gov (United States)

Carter, Alison J.; Audsley, Neil C.

2004-05-01

Image compression is a computationally intensive task, which can be undertaken most efficiently by dedicated hardware. If a portable device is to carry out real-time compression on a variety of image types, then it may be useful to reconfigure the circuitry dynamically. Using commercial off-the shelf (COTS) chips, reconfiguration is usually implemented by a complete re-load from memory, but it is also possible to perform a partial reconfiguration. This work studies the use of programmable hardware devices to implement the lossless JPEG compression algorithm in real-time on a stream of independent image frames. The data rate is faster than can be compressed serially in hardware by a single processor, so the operation is split amongst several processors. These are implemented as programmable circuits, together with necessary buffering of input and output data. The timing of input and output, bearing in mind the different, and context-dependent amounts of data due to Huffman coding, is analyzed using storage-timing graphs. Because there may be differing parameters from one frame to the next, several different configurations are prepared and stored, ready to load as required. The scheduling of these reconfigurations, and the distribution/recombination of data streams is studied, giving an analysis of the real-time performance.

Reliability of the Alzheimer's disease assessment scale (ADAS-Cog) in longitudinal studies.

Science.gov (United States)

Khan, Anzalee; Yavorsky, Christian; DiClemente, Guillermo; Opler, Mark; Liechti, Stacy; Rothman, Brian; Jovic, Sofija

2013-11-01

Considering the scarcity of longitudinal assessments of reliability, there is need for a more precise understanding of cognitive decline in Alzheimer's Disease (AD). The primary goal was to assess longitudinal changes in inter-rater reliability, test retest reliability and internal consistency of scores of the ADAS-Cog. 2,618 AD subjects were enrolled in seven randomized, double-blind, placebo-controlled, multicenter-trials from 1986 to 2009. Reliability, internal-consistency and cross-sectional analysis of ADAS-Cog and MMSE across seven visits were examined. Intra-class correlation (ICC) for ADAS-Cog was moderate to high supporting their reliability. Absolute Agreement ICCs 0.392 (Visit-7) to 0.806 (Visit-2) showed a progressive decrease in correlations across time. Item analysis revealed a decrease in item correlations, with the lowest correlations for Visit 7 for Commands (ICC=0.148), Comprehension (ICC=0.092), Spoken Language (ICC=0.044). Suitable assessment of AD treatments is maintained through accurate measurement of clinically significant outcomes. Targeted rater education ADAS-Cog items over-time can improve ability to administer and score the scale.

Ada Namelist Package

Science.gov (United States)

Klumpp, Allan R.

1991-01-01

Ada Namelist Package, developed for Ada programming language, enables calling program to read and write FORTRAN-style namelist files. Features are: handling of any combination of types defined by user; ability to read vectors, matrices, and slices of vectors and matrices; handling of mismatches between variables in namelist file and those in programmed list of namelist variables; and ability to avoid searching entire input file for each variable. Principle benefits derived by user: ability to read and write namelist-readable files, ability to detect most file errors in initialization phase, and organization keeping number of instantiated units to few packages rather than to many subprograms.

Fine-Tuning ADAS Algorithm Parameters for Optimizing Traffic ...

Science.gov (United States)

With the development of the Connected Vehicle technology that facilitates wirelessly communication among vehicles and road-side infrastructure, the Advanced Driver Assistance Systems (ADAS) can be adopted as an effective tool for accelerating traffic safety and mobility optimization at various highway facilities. To this end, the traffic management centers identify the optimal ADAS algorithm parameter set that enables the maximum improvement of the traffic safety and mobility performance, and broadcast the optimal parameter set wirelessly to individual ADAS-equipped vehicles. After adopting the optimal parameter set, the ADAS-equipped drivers become active agents in the traffic stream that work collectively and consistently to prevent traffic conflicts, lower the intensity of traffic disturbances, and suppress the development of traffic oscillations into heavy traffic jams. Successful implementation of this objective requires the analysis capability of capturing the impact of the ADAS on driving behaviors, and measuring traffic safety and mobility performance under the influence of the ADAS. To address this challenge, this research proposes a synthetic methodology that incorporates the ADAS-affected driving behavior modeling and state-of-the-art microscopic traffic flow modeling into a virtually simulated environment. Building on such an environment, the optimal ADAS algorithm parameter set is identified through an optimization programming framework to enable th

Design Method of ADAS for Urban Electric Vehicle Based on Virtual Prototyping

Directory of Open Access Journals (Sweden)

Katarzyna Jezierska-Krupa

2018-01-01

Full Text Available Since 2012, the Smart Power Team has been actively participating in the Shell Eco-marathon, which is a worldwide competition. From the very beginning, the team has been working to increase driver’s safety on the road by developing Advanced Driver Assistance Systems. This paper presents unique method for designing ADAS systems in order to minimize the costs of the design phase and system implementation and, at the same time, to maximize the positive effect the system has on driver and vehicle safety. The described method is based on using virtual prototyping tool to simulate the system performance in real-life situations. This approach enabled an iterative design process, which resulted in reduction of errors with almost no prototyping and testing costs.

Performance analysis of a real-time database with optimistic concurrency control

NARCIS (Netherlands)

Sassen, S.A.E.; Wal, van der J.

1997-01-01

For a real-time shared-memory database with Optimistic Concurrency Control (OCC), an approximation for the transaction response-time distribution and thus for the deadline miss probability is obtained. Transactions arrive at the database according to a Poisson process. There is a limited number of

Wind, METOP ASCAT, 0.25 degrees, Global, Near Real Time, Modulus

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NOAA CoastWatch distributes near real time wind divergence data originating with wind velocity measurements from the ASCAT instrument onboard EUMETSAT's ASCAT...

Wind, METOP ASCAT, 0.25 degrees, Global, Near Real Time, Zonal

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NOAA CoastWatch distributes near real time wind divergence data originating with wind velocity measurements from the ASCAT instrument onboard EUMETSAT's ASCAT...

Investigation of Real-Time Two-Dimensional Visualization of Fuel Spray Liquid/Vapor Distribution via Exciplex Fluorescence.

Science.gov (United States)

1987-08-30

EXCIPLEX FLUORESCENCE ~N 0FINAL REPORT 00 JAMES F. VERDIECK AND ARTHUR A. ROTUNNO UNITED TECHNOLOGIES RESEARCH CENTER 0 AND LYNN A. MELTON D I UNIVERSITY...DOCUMENTATION. "NWA 0. INVESTIGATION OF REAL-TINE TWO-DIMENSIONAL VISUALIZATION OF FUEL SPRAY LIQUID/VAPOR DISTRIBUTION VIA EXCIPLEX FLUORESCENCE FINAL...Spray Liquid/Vapor Distribution Via Exciplex Fluorescen , - 12. PERSONAL AUTHOR(S) J. F. Yeardierk. A- A. Rnriiunn-l L_ A. Millo - 13a TYPE OF REPORT

A real-time multi-sensor fusion platform for automated driving application development

NARCIS (Netherlands)

Bijlsma, T.; Kwakkernaat, M.; Mnatsakanyan, M.

2015-01-01

Advanced Driver Assistance Systems (ADAS) become standard and sometimes mandatory for vehicles, e.g. autonomous emergency braking. Future vehicles will include multiple ADAS that assist with safety-critical operations. For efficiency and effectiveness, these ADAS should share resources, information

Ada (Trade Name) Bibliography. Volume 1.

Science.gov (United States)

1983-05-01

GLENN DOCUMENT NUMBER: 3268 TYPE: JOURNAL ARTICLE .5-., SCIENCE VOL 215 ISSUE 34 PP. 775-779S In this article, two principal themes are observed in...AINST LANAN RD NAY 83 ND9S-8-C-936 UNCLASSIFIED F/6 12/5 ML -4.4 ’-4-4----" ’°p..l i . d N N L. 131 t ’ll /II~ Ada Bibliography Volume I 95 𔃾- This...BUDAPEST,HUNGARY 4102 -01 ON THE TYPE CONCEPT OF ADA 6224 -03 UNORTHOGONALITIES IN THE IDENTIFICATION RULES IN ADA BACON, GLENN , IBM SANTA TERESA LABS

A real time study on condition monitoring of distribution transformer using thermal imager

Science.gov (United States)

Mariprasath, T.; Kirubakaran, V.

2018-05-01

The transformer is one of the critical apparatus in the power system. At any cost, a few minutes of outages harshly influence the power system. Hence, prevention-based maintenance technique is very essential. The continuous conditioning and monitoring technology significantly increases the life span of the transformer, as well as reduces the maintenance cost. Hence, conditioning and monitoring of transformer's temperature are very essential. In this paper, a critical review has been made on various conditioning and monitoring techniques. Furthermore, a new method, hot spot indication technique, is discussed. Also, transformer's operating condition is monitored by using thermal imager. From the thermal analysis, it is inferred that major hotspot locations are appearing at connection lead out; also, the bushing of the transformer is the very hottest spot in transformer, so monitoring the level of oil is essential. Alongside, real time power quality analysis has been carried out using the power analyzer. It shows that industrial drives are injecting current harmonics to the distribution network, which causes the power quality problem on the grid. Moreover, the current harmonic limit has exceeded the IEEE standard limit. Hence, the adequate harmonics suppression technique is need an hour.

Toward the efficient implementation of expert systems in Ada

Science.gov (United States)

Lee, S. Daniel

1990-01-01

Here, the authors describe Ada language issues encountered during the development of ART-Ada, an expert system tool for Ada deployment. ART-Ada is being used to implement several expert system applications for the Space Station Freedom and the U.S. Air Force. Additional information is given on dynamic memory allocation.

A real-time architecture for time-aware agents.

Science.gov (United States)

Prouskas, Konstantinos-Vassileios; Pitt, Jeremy V

2004-06-01

This paper describes the specification and implementation of a new three-layer time-aware agent architecture. This architecture is designed for applications and environments where societies of humans and agents play equally active roles, but interact and operate in completely different time frames. The architecture consists of three layers: the April real-time run-time (ART) layer, the time aware layer (TAL), and the application agents layer (AAL). The ART layer forms the underlying real-time agent platform. An original online, real-time, dynamic priority-based scheduling algorithm is described for scheduling the computation time of agent processes, and it is shown that the algorithm's O(n) complexity and scalable performance are sufficient for application in real-time domains. The TAL layer forms an abstraction layer through which human and agent interactions are temporally unified, that is, handled in a common way irrespective of their temporal representation and scale. A novel O(n2) interaction scheduling algorithm is described for predicting and guaranteeing interactions' initiation and completion times. The time-aware predicting component of a workflow management system is also presented as an instance of the AAL layer. The described time-aware architecture addresses two key challenges in enabling agents to be effectively configured and applied in environments where humans and agents play equally active roles. It provides flexibility and adaptability in its real-time mechanisms while placing them under direct agent control, and it temporally unifies human and agent interactions.

Real-time networked control of an industrial robot manipulator via discrete-time second-order sliding modes

Science.gov (United States)

Massimiliano Capisani, Luca; Facchinetti, Tullio; Ferrara, Antonella

2010-08-01

This article presents the networked control of a robotic anthropomorphic manipulator based on a second-order sliding mode technique, where the control objective is to track a desired trajectory for the manipulator. The adopted control scheme allows an easy and effective distribution of the control algorithm over two networked machines. While the predictability of real-time tasks execution is achieved by the Soft Hard Real-Time Kernel (S.Ha.R.K.) real-time operating system, the communication is established via a standard Ethernet network. The performances of the control system are evaluated under different experimental system configurations using, to perform the experiments, a COMAU SMART3-S2 industrial robot, and the results are analysed to put into evidence the robustness of the proposed approach against possible network delays, packet losses and unmodelled effects.

End-User Applications of Real-Time Earthquake Information in Europe

Science.gov (United States)

Cua, G. B.; Gasparini, P.; Giardini, D.; Zschau, J.; Filangieri, A. R.; Reakt Wp7 Team

2011-12-01

The primary objective of European FP7 project REAKT (Strategies and Tools for Real-Time Earthquake Risk Reduction) is to improve the efficiency of real-time earthquake risk mitigation methods and their capability of protecting structures, infrastructures, and populations. REAKT aims to address the issues of real-time earthquake hazard and response from end-to-end, with efforts directed along the full spectrum of methodology development in earthquake forecasting, earthquake early warning, and real-time vulnerability systems, through optimal decision-making, and engagement and cooperation of scientists and end users for the establishment of best practices for use of real-time information. Twelve strategic test cases/end users throughout Europe have been selected. This diverse group of applications/end users includes civil protection authorities, railway systems, hospitals, schools, industrial complexes, nuclear plants, lifeline systems, national seismic networks, and critical structures. The scale of target applications covers a wide range, from two school complexes in Naples, to individual critical structures, such as the Rion Antirion bridge in Patras, and the Fatih Sultan Mehmet bridge in Istanbul, to large complexes, such as the SINES industrial complex in Portugal and the Thessaloniki port area, to distributed lifeline and transportation networks and nuclear plants. Some end-users are interested in in-depth feasibility studies for use of real-time information and development of rapid response plans, while others intend to install real-time instrumentation and develop customized automated control systems. From the onset, REAKT scientists and end-users will work together on concept development and initial implementation efforts using the data products and decision-making methodologies developed with the goal of improving end-user risk mitigation. The aim of this scientific/end-user partnership is to ensure that scientific efforts are applicable to operational

Towards Real-Time Argumentation

Directory of Open Access Journals (Sweden)

Vicente JULIÁN

2016-07-01

Full Text Available In this paper, we deal with the problem of real-time coordination with the more general approach of reaching real-time agreements in MAS. Concretely, this work proposes a real-time argumentation framework in an attempt to provide agents with the ability of engaging in argumentative dialogues and come with a solution for their underlying agreement process within a bounded period of time. The framework has been implemented and evaluated in the domain of a customer support application. Concretely, we consider a society of agents that act on behalf of a group of technicians that must solve problems in a Technology Management Centre (TMC within a bounded time. This centre controls every process implicated in the provision of technological and customer support services to private or public organisations by means of a call centre. The contract signed between the TCM and the customer establishes penalties if the specified time is exceeded.

Real-time motion-adaptive-optimization (MAO) in TomoTherapy

Energy Technology Data Exchange (ETDEWEB)

Lu Weiguo; Chen Mingli; Ruchala, Kenneth J; Chen Quan; Olivera, Gustavo H [TomoTherapy Inc., 1240 Deming Way, Madison, WI (United States); Langen, Katja M; Kupelian, Patrick A [MD Anderson Cancer Center-Orlando, Orlando, FL (United States)], E-mail: wlu@tomotherapy.com

2009-07-21

IMRT delivery follows a planned leaf sequence, which is optimized before treatment delivery. However, it is hard to model real-time variations, such as respiration, in the planning procedure. In this paper, we propose a negative feedback system of IMRT delivery that incorporates real-time optimization to account for intra-fraction motion. Specifically, we developed a feasible workflow of real-time motion-adaptive-optimization (MAO) for TomoTherapy delivery. TomoTherapy delivery is characterized by thousands of projections with a fast projection rate and ultra-fast binary leaf motion. The technique of MAO-guided delivery calculates (i) the motion-encoded dose that has been delivered up to any given projection during the delivery and (ii) the future dose that will be delivered based on the estimated motion probability and future fluence map. These two pieces of information are then used to optimize the leaf open time of the upcoming projection right before its delivery. It consists of several real-time procedures, including 'motion detection and prediction', 'delivered dose accumulation', 'future dose estimation' and 'projection optimization'. Real-time MAO requires that all procedures are executed in time less than the duration of a projection. We implemented and tested this technique using a TomoTherapy (registered) research system. The MAO calculation took about 100 ms per projection. We calculated and compared MAO-guided delivery with two other types of delivery, motion-without-compensation delivery (MD) and static delivery (SD), using simulated 1D cases, real TomoTherapy plans and the motion traces from clinical lung and prostate patients. The results showed that the proposed technique effectively compensated for motion errors of all test cases. Dose distributions and DVHs of MAO-guided delivery approached those of SD, for regular and irregular respiration with a peak-to-peak amplitude of 3 cm, and for medium and large

Real-time motion-adaptive-optimization (MAO) in TomoTherapy

International Nuclear Information System (INIS)

Lu Weiguo; Chen Mingli; Ruchala, Kenneth J; Chen Quan; Olivera, Gustavo H; Langen, Katja M; Kupelian, Patrick A

2009-01-01

IMRT delivery follows a planned leaf sequence, which is optimized before treatment delivery. However, it is hard to model real-time variations, such as respiration, in the planning procedure. In this paper, we propose a negative feedback system of IMRT delivery that incorporates real-time optimization to account for intra-fraction motion. Specifically, we developed a feasible workflow of real-time motion-adaptive-optimization (MAO) for TomoTherapy delivery. TomoTherapy delivery is characterized by thousands of projections with a fast projection rate and ultra-fast binary leaf motion. The technique of MAO-guided delivery calculates (i) the motion-encoded dose that has been delivered up to any given projection during the delivery and (ii) the future dose that will be delivered based on the estimated motion probability and future fluence map. These two pieces of information are then used to optimize the leaf open time of the upcoming projection right before its delivery. It consists of several real-time procedures, including 'motion detection and prediction', 'delivered dose accumulation', 'future dose estimation' and 'projection optimization'. Real-time MAO requires that all procedures are executed in time less than the duration of a projection. We implemented and tested this technique using a TomoTherapy (registered) research system. The MAO calculation took about 100 ms per projection. We calculated and compared MAO-guided delivery with two other types of delivery, motion-without-compensation delivery (MD) and static delivery (SD), using simulated 1D cases, real TomoTherapy plans and the motion traces from clinical lung and prostate patients. The results showed that the proposed technique effectively compensated for motion errors of all test cases. Dose distributions and DVHs of MAO-guided delivery approached those of SD, for regular and irregular respiration with a peak-to-peak amplitude of 3 cm, and for medium and large prostate motions. The results conceptually

Demo: Distributed Real-Time Generative 3D Hand Tracking using Edge GPGPU Acceleration

DEFF Research Database (Denmark)

Qammaz, Ammar; Kosta, Sokol; Kyriazis, Nikolaos

2018-01-01

computations locally. The network connection takes the place of a GPGPU accelerator and sharing resources with a larger workstation becomes the acceleration mechanism. The unique properties of a generative optimizer are examined and constitute a challenging use-case, since the requirement for real......This work demonstrates a real-time 3D hand tracking application that runs via computation offloading. The proposed framework enables the application to run on low-end mobile devices such as laptops and tablets, despite the fact that they lack the sufficient hardware to perform the required...

Real-time PCR in virology.

Science.gov (United States)

Mackay, Ian M; Arden, Katherine E; Nitsche, Andreas

2002-03-15

The use of the polymerase chain reaction (PCR) in molecular diagnostics has increased to the point where it is now accepted as the gold standard for detecting nucleic acids from a number of origins and it has become an essential tool in the research laboratory. Real-time PCR has engendered wider acceptance of the PCR due to its improved rapidity, sensitivity, reproducibility and the reduced risk of carry-over contamination. There are currently five main chemistries used for the detection of PCR product during real-time PCR. These are the DNA binding fluorophores, the 5' endonuclease, adjacent linear and hairpin oligoprobes and the self-fluorescing amplicons, which are described in detail. We also discuss factors that have restricted the development of multiplex real-time PCR as well as the role of real-time PCR in quantitating nucleic acids. Both amplification hardware and the fluorogenic detection chemistries have evolved rapidly as the understanding of real-time PCR has developed and this review aims to update the scientist on the current state of the art. We describe the background, advantages and limitations of real-time PCR and we review the literature as it applies to virus detection in the routine and research laboratory in order to focus on one of the many areas in which the application of real-time PCR has provided significant methodological benefits and improved patient outcomes. However, the technology discussed has been applied to other areas of microbiology as well as studies of gene expression and genetic disease.

Real-time control environment for the RFX experiment

International Nuclear Information System (INIS)

Barana, O.; Cavinato, M.; Luchetta, A.; Manduchi, G.; Taliercio, C.

2005-01-01

A comprehensive set of control schemes can be presently implemented on RFX due to the enhanced load assembly and renewed power supply system. The schemes include: plasma equilibrium control and resistive wall mode stabilization, aiming at controlling actively the discharge when the passive action of the shell vanishes; the rotation of the localised helical deformation to minimize the enhanced plasma-wall interaction; the MHD mode control and the 'intelligent shell', aiming at achieving a better comprehension of the underlying physics. To the purpose, an integrated, distributed, digital system has been developed consisting of a set of computing nodes. Each node can act either as pre-processing or control station, the former acquiring raw data and computing intermediate control parameters, the latter executing control algorithms and driving the power amplifiers. An overview of the system architecture is presented in the paper with reference to the software real-time environment providing both basic functions, such as data read-out and real-time communication, and useful tools to program control algorithms, to perform simulations and to commission the system. To simulate the control schemes, the real-time environment is extended to include a so called 'simulation mode', in which the real-time nodes exchange their input/output signals with one station running a suitable model of the experiment, for instance the two dimensional FEM code MAXFEA in the case of the equilibrium control. In this way the control system can be tested offline and the time needed for the commissioning of algorithms reduced

Real-time appraisal of the spatially distributed heat related health risk and energy demand of cities

Science.gov (United States)

Keramitsoglou, Iphigenia; Kiranoudis, Chris T.; Sismanidis, Panagiotis

2016-08-01

The Urban Heat Island (UHI) is an adverse environmental effect of urbanization that increases the energy demand of cities, impacts the human health, and intensifies and prolongs heatwave events. To facilitate the study of UHIs the Institute for Astronomy, Astrophysics, Space Applications and Remote Sensing of the National Observatory of Athens (IAASARS/NOA) has developed an operational real-time system that exploits remote sensing image data from Meteosat Second Generation - Spinning Enhanced Visible and Infrared Imager (MSG-SEVIRI) and generates high spatiotemporal land surface temperature (LST) and 2 m air temperature (TA) time series. These datasets form the basis for the generation of higher value products and services related to energy demand and heat-related health issues. These products are the heatwave hazard (HZ); the HUMIDEX (i.e. an index that describes the temperature felt by an individual exposed to heat and humidity); and the cooling degrees (CD; i.e. a measure that reflects the energy needed to cool a building). The spatiotemporal characteristics of HZ, HUMIDEX and CD are unique (1 km/5 min) and enable the appraisal of the spatially distributed heat related health risk and energy demand of cities. In this paper, the real time generation of the high spatiotemporal HZ, HUMIDEX and CD products is discussed. In addition, a case study corresponding to Athens' September 2015 heatwave is presented so as to demonstrate their capabilities. The overall aim of the system is to provide high quality data to several different end users, such as health responders, and energy suppliers. The urban thermal monitoring web service is available at http://snf-652558.vm.okeanos.grnet.gr/treasure/portal/info.html.

A high performance load balance strategy for real-time multicore systems.

Science.gov (United States)

Cho, Keng-Mao; Tsai, Chun-Wei; Chiu, Yi-Shiuan; Yang, Chu-Sing

2014-01-01

Finding ways to distribute workloads to each processor core and efficiently reduce power consumption is of vital importance, especially for real-time systems. In this paper, a novel scheduling algorithm is proposed for real-time multicore systems to balance the computation loads and save power. The developed algorithm simultaneously considers multiple criteria, a novel factor, and task deadline, and is called power and deadline-aware multicore scheduling (PDAMS). Experiment results show that the proposed algorithm can greatly reduce energy consumption by up to 54.2% and the deadline times missed, as compared to the other scheduling algorithms outlined in this paper.

Real time programming environment for Windows

Energy Technology Data Exchange (ETDEWEB)

LaBelle, D.R. [LaBelle (Dennis R.), Clifton Park, NY (United States)

1998-04-01

This document provides a description of the Real Time Programming Environment (RTProE). RTProE tools allow a programmer to create soft real time projects under general, multi-purpose operating systems. The basic features necessary for real time applications are provided by RTProE, leaving the programmer free to concentrate efforts on his specific project. The current version supports Microsoft Windows{trademark} 95 and NT. The tasks of real time synchronization and communication with other programs are handled by RTProE. RTProE includes a generic method for connecting a graphical user interface (GUI) to allow real time control and interaction with the programmer`s product. Topics covered in this paper include real time performance issues, portability, details of shared memory management, code scheduling, application control, Operating System specific concerns and the use of Computer Aided Software Engineering (CASE) tools. The development of RTProE is an important step in the expansion of the real time programming community. The financial costs associated with using the system are minimal. All source code for RTProE has been made publicly available. Any person with access to a personal computer, Windows 95 or NT, and C or FORTRAN compilers can quickly enter the world of real time modeling and simulation.

Ekman Upwelling, METOP ASCAT, 0.25 degrees, Global, Near Real Time

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NOAA CoastWatch distributes near real time Ekman current (in zonal, meridional, and modulus sets) and Ekman upwelling data. This data begins with wind velocity...

A real-time assessment of measurement uncertainty in the experimental characterization of sprays

International Nuclear Information System (INIS)

Panão, M R O; Moreira, A L N

2008-01-01

This work addresses the estimation of the measurement uncertainty of discrete probability distributions used in the characterization of sprays. A real-time assessment of this measurement uncertainty is further investigated, particularly concerning the informative quality of the measured distribution and the influence of acquiring additional information on the knowledge retrieved from statistical analysis. The informative quality is associated with the entropy concept as understood in information theory (Shannon entropy), normalized by the entropy of the most informative experiment. A new empirical correlation is derived between the error accuracy of a discrete cumulative probability distribution and the normalized Shannon entropy. The results include case studies using: (i) spray impingement measurements to study the applicability of the real-time assessment of measurement uncertainty, and (ii) the simulation of discrete probability distributions of unknown shape or function to test the applicability of the new correlation

MARTe: A Multiplatform Real-Time Framework

Science.gov (United States)

Neto, André C.; Sartori, Filippo; Piccolo, Fabio; Vitelli, Riccardo; De Tommasi, Gianmaria; Zabeo, Luca; Barbalace, Antonio; Fernandes, Horacio; Valcarcel, Daniel F.; Batista, Antonio J. N.

2010-04-01

Development of real-time applications is usually associated with nonportable code targeted at specific real-time operating systems. The boundary between hardware drivers, system services, and user code is commonly not well defined, making the development in the target host significantly difficult. The Multithreaded Application Real-Time executor (MARTe) is a framework built over a multiplatform library that allows the execution of the same code in different operating systems. The framework provides the high-level interfaces with hardware, external configuration programs, and user interfaces, assuring at the same time hard real-time performances. End-users of the framework are required to define and implement algorithms inside a well-defined block of software, named Generic Application Module (GAM), that is executed by the real-time scheduler. Each GAM is reconfigurable with a set of predefined configuration meta-parameters and interchanges information using a set of data pipes that are provided as inputs and required as output. Using these connections, different GAMs can be chained either in series or parallel. GAMs can be developed and debugged in a non-real-time system and, only once the robustness of the code and correctness of the algorithm are verified, deployed to the real-time system. The software also supplies a large set of utilities that greatly ease the interaction and debugging of a running system. Among the most useful are a highly efficient real-time logger, HTTP introspection of real-time objects, and HTTP remote configuration. MARTe is currently being used to successfully drive the plasma vertical stabilization controller on the largest magnetic confinement fusion device in the world, with a control loop cycle of 50 ?s and a jitter under 1 ?s. In this particular project, MARTe is used with the Real-Time Application Interface (RTAI)/Linux operating system exploiting the new ?86 multicore processors technology.

Advanced real-time control systems for magnetically confined fusion plasmas

International Nuclear Information System (INIS)

Goncalves, B.; Sousa, J.; Fernandes, H.; Rodrigues, A.P.; Carvalho, B.B.; Neto, A.; Varandas, C.A.F.

2008-01-01

Real-time control of magnetically confined plasmas is a critical issue for the safety, operation and high performance scientific exploitation of the experimental devices on regimes beyond the current operation frontiers. The number of parameters and the data volumes used for the plasma properties identification scale normally not only with the machine size but also with the technology improvements, leading to a great complexity of the plant system. A strong computational power and fast communication infrastructure are needed to handle in real-time this information, allowing just-in-time decisions to achieve the fusion critical plasma conditions. These advanced control systems require a tiered infrastructure including the hardware layer, the signal-processing middleware, real-time timing and data transport, the real-time operating system tools and drivers, the framework for code development, simulation, deployment and experiment parameterization and the human real-time plasma condition monitoring and management. This approach is being implemented at CFN by offering a vertical solution for the forthcoming challenges, including ITER, the first experimental fusion reactor. A given set of tools and systems are described on this paper, namely: (i) an ATCA based hardware multiple-input-multiple-output (MIMO) platform, PCI and PCIe acquisition and control modules; (ii) FPGA and DSP parallelized signal processing algorithms; (iii) a signal data and event distribution system over a 2.5/10Gb optical network with sub-microsecond latencies; (iv) RTAI and Linux drivers; and (v) the FireSignal, FusionTalk, SDAS FireCalc application tools. (author)

Implementation of SoC Based Real-Time Electromagnetic Transient Simulator

Directory of Open Access Journals (Sweden)

I. Herrera-Leandro

2017-01-01

Full Text Available Real-time electromagnetic transient simulators are important tools in the design stage of new control and protection systems for power systems. Real-time simulators are used to test and stress new devices under similar conditions that the device will deal with in a real network with the purpose of finding errors and bugs in the design. The computation of an electromagnetic transient is complex and computationally demanding, due to features such as the speed of the phenomenon, the size of the network, and the presence of time variant and nonlinear elements in the network. In this work, the development of a SoC based real-time and also offline electromagnetic transient simulator is presented. In the design, the required performance is met from two sides, (a using a technique to split the power system into smaller subsystems, which allows parallelizing the algorithm, and (b with specialized and parallel hardware designed to boost the solution flow. The results of this work have shown that for the proposed case studies, based on a balanced distribution of the node of subsystems, the proposed approach has decreased the total simulation time by up to 99 times compared with the classical approach running on a single high performance 32-bit embedded processor ARM-Cortex A9.

Real-Time and Real-Fast Performance of General-Purpose and Real-Time Operating Systems in Multithreaded Physical Simulation of Complex Mechanical Systems

Directory of Open Access Journals (Sweden)

Carlos Garre

2014-01-01

Full Text Available Physical simulation is a valuable tool in many fields of engineering for the tasks of design, prototyping, and testing. General-purpose operating systems (GPOS are designed for real-fast tasks, such as offline simulation of complex physical models that should finish as soon as possible. Interfacing hardware at a given rate (as in a hardware-in-the-loop test requires instead maximizing time determinism, for which real-time operating systems (RTOS are designed. In this paper, real-fast and real-time performance of RTOS and GPOS are compared when simulating models of high complexity with large time steps. This type of applications is usually present in the automotive industry and requires a good trade-off between real-fast and real-time performance. The performance of an RTOS and a GPOS is compared by running a tire model scalable on the number of degrees-of-freedom and parallel threads. The benchmark shows that the GPOS present better performance in real-fast runs but worse in real-time due to nonexplicit task switches and to the latency associated with interprocess communication (IPC and task switch.

GNSS global real-time augmentation positioning: Real-time precise satellite clock estimation, prototype system construction and performance analysis

Science.gov (United States)

Chen, Liang; Zhao, Qile; Hu, Zhigang; Jiang, Xinyuan; Geng, Changjiang; Ge, Maorong; Shi, Chuang

2018-01-01

Lots of ambiguities in un-differenced (UD) model lead to lower calculation efficiency, which isn't appropriate for the high-frequency real-time GNSS clock estimation, like 1 Hz. Mixed differenced model fusing UD pseudo-range and epoch-differenced (ED) phase observations has been introduced into real-time clock estimation. In this contribution, we extend the mixed differenced model for realizing multi-GNSS real-time clock high-frequency updating and a rigorous comparison and analysis on same conditions are performed to achieve the best real-time clock estimation performance taking the efficiency, accuracy, consistency and reliability into consideration. Based on the multi-GNSS real-time data streams provided by multi-GNSS Experiment (MGEX) and Wuhan University, GPS + BeiDou + Galileo global real-time augmentation positioning prototype system is designed and constructed, including real-time precise orbit determination, real-time precise clock estimation, real-time Precise Point Positioning (RT-PPP) and real-time Standard Point Positioning (RT-SPP). The statistical analysis of the 6 h-predicted real-time orbits shows that the root mean square (RMS) in radial direction is about 1-5 cm for GPS, Beidou MEO and Galileo satellites and about 10 cm for Beidou GEO and IGSO satellites. Using the mixed differenced estimation model, the prototype system can realize high-efficient real-time satellite absolute clock estimation with no constant clock-bias and can be used for high-frequency augmentation message updating (such as 1 Hz). The real-time augmentation message signal-in-space ranging error (SISRE), a comprehensive accuracy of orbit and clock and effecting the users' actual positioning performance, is introduced to evaluate and analyze the performance of GPS + BeiDou + Galileo global real-time augmentation positioning system. The statistical analysis of real-time augmentation message SISRE is about 4-7 cm for GPS, whlile 10 cm for Beidou IGSO/MEO, Galileo and about 30 cm

Feasibility study of the real-time IMRT dosimetry using a scintillation screen

Energy Technology Data Exchange (ETDEWEB)

Lim, Sang Wook; Yi, Byong Yong; Ko, Young Eun [Asan Medical Center, College of Medicine, University of Ulsan, Seoul (Korea, Republic of)] (and others)

2004-03-15

To study the feasibility of verifying real-time 2-D dose distribution measurement system with the scintillation screen for the quality assurance. The water phantom consisted of a scintillation screen (LANEX fast screen, Kodak, USA) that was axially located in the middle of an acrylic cylinder with a diameter of 25 cm. The charge-coupled device (CCD) camera was attached to the phantom in order to capture the visible light from the scintillation screen. To observe the dose distribution in real time, the intensity of the light from the scintillator was converted to a dosage. The isodose contours of the calculations from RTP and those of the measurements using the scintillation screen were compared for the arc therapy and the intensity modulated radiation therapy (IMRT). The kernel, expressed as a multiplication of two error functions, was obtained in order to correct the sensitivity of the CCD of the camera and the scintillation screen. When comparing the calculated isodose and measured isodose, a discrepancy of less than 8 mm in the high dose region was observed. Using the 2-D dosimetry system, the relationship between the light and the dosage could be found, and real-time verification of the dose distribution was feasible.

Feasibility study of the real-time IMRT dosimetry using a scintillation screen

International Nuclear Information System (INIS)

Lim, Sang Wook; Yi, Byong Yong; Ko, Young Eun

2004-01-01

To study the feasibility of verifying real-time 2-D dose distribution measurement system with the scintillation screen for the quality assurance. The water phantom consisted of a scintillation screen (LANEX fast screen, Kodak, USA) that was axially located in the middle of an acrylic cylinder with a diameter of 25 cm. The charge-coupled device (CCD) camera was attached to the phantom in order to capture the visible light from the scintillation screen. To observe the dose distribution in real time, the intensity of the light from the scintillator was converted to a dosage. The isodose contours of the calculations from RTP and those of the measurements using the scintillation screen were compared for the arc therapy and the intensity modulated radiation therapy (IMRT). The kernel, expressed as a multiplication of two error functions, was obtained in order to correct the sensitivity of the CCD of the camera and the scintillation screen. When comparing the calculated isodose and measured isodose, a discrepancy of less than 8 mm in the high dose region was observed. Using the 2-D dosimetry system, the relationship between the light and the dosage could be found, and real-time verification of the dose distribution was feasible

GRASP/Ada (Graphical Representations of Algorithms, Structures, and Processes for Ada): The development of a program analysis environment for Ada. Reverse engineering tools for Ada, task 1, phase 2

Science.gov (United States)

Cross, James H., II

1990-01-01

The study, formulation, and generation of structures for Ada (GRASP/Ada) are discussed in this second phase report of a three phase effort. Various graphical representations that can be extracted or generated from source code are described and categorized with focus on reverse engineering. The overall goal is to provide the foundation for a CASE (computer-aided software design) environment in which reverse engineering and forward engineering (development) are tightly coupled. Emphasis is on a subset of architectural diagrams that can be generated automatically from source code with the control structure diagram (CSD) included for completeness.

Monitoring beryllium during site cleanup and closure using a real-time analyzer

Energy Technology Data Exchange (ETDEWEB)

Schlager, R.J.; Sappey, A.D.; French, P.D. [ADA Technologies, Inc., Englewood, CO (United States)

1998-12-31

Beryllium metal has a number of unique properties that have been exploited for use in commercial and government applications. Airborne beryllium particles can represent a significant human health hazard if deposited in the lungs. These particles can cause immunologically-mediated chronic granulomatous lung disease (chronic beryllium disease). Traditional methods of monitoring airborne beryllium involve collecting samples of air within the work area using a filter. The filter then undergoes chemical analysis to determine the amount of beryllium collected during the sampling period. These methods are time-consuming and results are known only after a potential exposure has occurred. The need for monitoring exposures in real time has prompted government and commercial companies to develop instrumentation that will allow for the real time assessment of short-term exposures so that adequate protection for workers in contaminated environments can be provided. Such an analyzer provides a tool that will allow government and commercial sites to be cleaned up in a more safe and effective manner since exposure assessments can be made instantaneously. This paper describes the development and initial testing of an analyzer for monitoring airborne beryllium using a technique known as Laser-Induced Breakdown Spectroscopy (LIBS). Energy from a focused, pulsed laser is used to vaporize a sample and create an intense plasma. The light emitted from the plasma is analyzed to determine the quantity of beryllium in the sampled air. A commercial prototype analyzer has been fabricated and tested in a program conducted by Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Lovelace Respiratory Research Institute, and ADA Technologies, Inc. Design features of the analyzer and preliminary test results are presented.

A distributed real-time system for event-driven control and dynamic data acquisition on a fusion plasma experiment

International Nuclear Information System (INIS)

Sousa, J.; Combo, A.; Batista, A.; Correia, M.; Trotman, D.; Waterhouse, J.; Varandas, C.A.F.

2000-01-01

A distributed real-time trigger and timing system, designed in a tree-type topology and implemented in VME and CAMAC versions, has been developed for a magnetic confinement fusion experiment. It provides sub-microsecond time latencies for the transport of small data objects allowing event-driven discharge control with failure counteraction, dynamic pre-trigger sampling and event recording as well as accurate simultaneous triggers and synchronism on all nodes with acceptable optimality and predictability of timeliness. This paper describes the technical characteristics of the hardware components (central unit composed by one or more reflector crates, event and synchronism reflector cards, event and pulse node module, fan-out and fan-in modules) as well as software for both tests and integration on a global data acquisition system. The results of laboratory operation for several configurations and the overall performance of the system are presented and analysed

Real time quantitative phase microscopy based on single-shot transport of intensity equation (ssTIE) method

Science.gov (United States)

Yu, Wei; Tian, Xiaolin; He, Xiaoliang; Song, Xiaojun; Xue, Liang; Liu, Cheng; Wang, Shouyu

2016-08-01

Microscopy based on transport of intensity equation provides quantitative phase distributions which opens another perspective for cellular observations. However, it requires multi-focal image capturing while mechanical and electrical scanning limits its real time capacity in sample detections. Here, in order to break through this restriction, real time quantitative phase microscopy based on single-shot transport of the intensity equation method is proposed. A programmed phase mask is designed to realize simultaneous multi-focal image recording without any scanning; thus, phase distributions can be quantitatively retrieved in real time. It is believed the proposed method can be potentially applied in various biological and medical applications, especially for live cell imaging.

Applicability of Agent-Based Technology for Acquisition, Monitoring and Process Control Systems at Real Time for Distributed Architectures

International Nuclear Information System (INIS)

Dorao, Carlos; Fontanini, H; Fernandez, R

2000-01-01

Modern industrial plants are characterized by their large size and higher complexity of the processes involved in their operations.The real time monitoring systems of theses plants must be used a distributed architecture.Due to the pressure of competitive markets, an efficient adaptability to changes must be present in the plants.Modifications in the plants due to changes in the lay-out, the introduction of newer supervision, control and monitoring technologies must not affect the integrity of the systems.The aim of this work is give an introduction to the agent-based technology and analyze it advantage for the development of a modern monitoring system

Administration and scoring variance on the ADAS-Cog.

Science.gov (United States)

Connor, Donald J; Sabbagh, Marwan N

2008-11-01

The Alzheimer's Disease Assessment Scale - Cognitive (ADAS-Cog) is the most commonly used primary outcome instrument in clinical trials for treatments of dementia. Variations in forms, administration procedures and scoring rules, along with rater turnover and intra-rater drift may decrease the reliability of the instrument. A survey of possible variations in the ADAS-Cog was administered to 26 volunteer raters at a clinical trials meeting. Results indicate notable protocol variations in the forms used, administration procedures, and scoring rules. Since change over time is used to determine treatment effect in clinical trials, standardizing the instrument's ambiguities and addressing common problems will greatly increase the instrument's reliability and thereby enhance its sensitivity to treatment effects.

ADAS: Atomic data, modelling and analysis for fusion

International Nuclear Information System (INIS)

Summers, H. P.; O'Mullane, M. G.; Whiteford, A. D.; Badnell, N. R.; Loch, S. D.

2007-01-01

The Atomic Data and Analysis Structure, ADAS, comprises extensive fundamental and derived atomic data collections, interactive codes for the manipulation and generation of collisional-radiative data and models, off-line codes for large scale fundamental atomic data production and codes for diagnostic analysis in the fusion and astrophysical environments. ADAS data are organized according to precise specifications, tuned to application and are assigned to numbered ADAS data formats. Some of these formats contain very large quantities of data and some have achieved wide-scale adoption in the fusion community.The paper focuses on recent extensions of ADAS designed to orient ADAS to the needs of ITER. The issue of heavy atomic species, expected to be present as ITER wall and divertor materials, dopants or control species, will be addressed with a view to the economized handling of the emission and ionisation state data needed for diagnostic spectral analysis. Charge exchange and beam emission spectroscopic capabilities and developments in ADAS will be reviewed from an ITER perspective and in the context of a shared analysis between fusion laboratories. Finally an overview and summary of current large scale fundamental data production in the framework of the ADAS project will be given and its intended availability in both fusion and astrophysics noted

Software reliability growth models with normal failure time distributions

International Nuclear Information System (INIS)

Okamura, Hiroyuki; Dohi, Tadashi; Osaki, Shunji

2013-01-01

This paper proposes software reliability growth models (SRGM) where the software failure time follows a normal distribution. The proposed model is mathematically tractable and has sufficient ability of fitting to the software failure data. In particular, we consider the parameter estimation algorithm for the SRGM with normal distribution. The developed algorithm is based on an EM (expectation-maximization) algorithm and is quite simple for implementation as software application. Numerical experiment is devoted to investigating the fitting ability of the SRGMs with normal distribution through 16 types of failure time data collected in real software projects

Model Checking Real-Time Systems

DEFF Research Database (Denmark)

Bouyer, Patricia; Fahrenberg, Uli; Larsen, Kim Guldstrand

2018-01-01

This chapter surveys timed automata as a formalism for model checking real-time systems. We begin with introducing the model, as an extension of finite-state automata with real-valued variables for measuring time. We then present the main model-checking results in this framework, and give a hint...

Modular specification of real-time systems

DEFF Research Database (Denmark)

Inal, Recep

1994-01-01

Duration Calculus, a real-time interval logic, has been embedded in the Z specification language to provide a notation for real-time systems that combines the modularisation and abstraction facilities of Z with a logic suitable for reasoning about real-time properties. In this article the notation...

Multiprocessor scheduling for real-time systems

CERN Document Server

Baruah, Sanjoy; Buttazzo, Giorgio

2015-01-01

This book provides a comprehensive overview of both theoretical and pragmatic aspects of resource-allocation and scheduling in multiprocessor and multicore hard-real-time systems.  The authors derive new, abstract models of real-time tasks that capture accurately the salient features of real application systems that are to be implemented on multiprocessor platforms, and identify rules for mapping application systems onto the most appropriate models.  New run-time multiprocessor scheduling algorithms are presented, which are demonstrably better than those currently used, both in terms of run-time efficiency and tractability of off-line analysis.  Readers will benefit from a new design and analysis framework for multiprocessor real-time systems, which will translate into a significantly enhanced ability to provide formally verified, safety-critical real-time systems at a significantly lower cost.

Automated Detection of Driver Fatigue Based on AdaBoost Classifier with EEG Signals

Directory of Open Access Journals (Sweden)

Jianfeng Hu

2017-08-01

Full Text Available Purpose: Driving fatigue has become one of the important causes of road accidents, there are many researches to analyze driver fatigue. EEG is becoming increasingly useful in the measuring fatigue state. Manual interpretation of EEG signals is impossible, so an effective method for automatic detection of EEG signals is crucial needed.Method: In order to evaluate the complex, unstable, and non-linear characteristics of EEG signals, four feature sets were computed from EEG signals, in which fuzzy entropy (FE, sample entropy (SE, approximate Entropy (AE, spectral entropy (PE, and combined entropies (FE + SE + AE + PE were included. All these feature sets were used as the input vectors of AdaBoost classifier, a boosting method which is fast and highly accurate. To assess our method, several experiments including parameter setting and classifier comparison were conducted on 28 subjects. For comparison, Decision Trees (DT, Support Vector Machine (SVM and Naive Bayes (NB classifiers are used.Results: The proposed method (combination of FE and AdaBoost yields superior performance than other schemes. Using FE feature extractor, AdaBoost achieves improved area (AUC under the receiver operating curve of 0.994, error rate (ERR of 0.024, Precision of 0.969, Recall of 0.984, F1 score of 0.976, and Matthews correlation coefficient (MCC of 0.952, compared to SVM (ERR at 0.035, Precision of 0.957, Recall of 0.974, F1 score of 0.966, and MCC of 0.930 with AUC of 0.990, DT (ERR at 0.142, Precision of 0.857, Recall of 0.859, F1 score of 0.966, and MCC of 0.716 with AUC of 0.916 and NB (ERR at 0.405, Precision of 0.646, Recall of 0.434, F1 score of 0.519, and MCC of 0.203 with AUC of 0.606. It shows that the FE feature set and combined feature set outperform other feature sets. AdaBoost seems to have better robustness against changes of ratio of test samples for all samples and number of subjects, which might therefore aid in the real-time detection of driver

The SSABLE system - Automated archive, catalog, browse and distribution of satellite data in near-real time

Science.gov (United States)

Simpson, James J.; Harkins, Daniel N.

1993-01-01

Historically, locating and browsing satellite data has been a cumbersome and expensive process. This has impeded the efficient and effective use of satellite data in the geosciences. SSABLE is a new interactive tool for the archive, browse, order, and distribution of satellite date based upon X Window, high bandwidth networks, and digital image rendering techniques. SSABLE provides for automatically constructing relational database queries to archived image datasets based on time, data, geographical location, and other selection criteria. SSABLE also provides a visual representation of the selected archived data for viewing on the user's X terminal. SSABLE is a near real-time system; for example, data are added to SSABLE's database within 10 min after capture. SSABLE is network and machine independent; it will run identically on any machine which satisfies the following three requirements: 1) has a bitmapped display (monochrome or greater); 2) is running the X Window system; and 3) is on a network directly reachable by the SSABLE system. SSABLE has been evaluated at over 100 international sites. Network response time in the United States and Canada varies between 4 and 7 s for browse image updates; reported transmission times to Europe and Australia typically are 20-25 s.

Prototyping real-time systems

OpenAIRE

Clynch, Gary

1994-01-01

The traditional software development paradigm, the waterfall life cycle model, is defective when used for developing real-time systems. This thesis puts forward an executable prototyping approach for the development of real-time systems. A prototyping system is proposed which uses ESML (Extended Systems Modelling Language) as a prototype specification language. The prototyping system advocates the translation of non-executable ESML specifications into executable LOOPN (Language of Object ...

Task Mapping and Partition Allocation for Mixed-Criticality Real-Time Systems

DEFF Research Database (Denmark)

Tamas-Selicean, Domitian; Pop, Paul

2012-01-01

In this paper we address the mapping of mixedcriticality hard real-time applications on distributed embedded architectures. We assume that the architecture provides both spatial and temporal partitioning, thus enforcing enough separation between applications. With temporal partitioning, each...

A High Performance Load Balance Strategy for Real-Time Multicore Systems

Directory of Open Access Journals (Sweden)

Keng-Mao Cho

2014-01-01

Full Text Available Finding ways to distribute workloads to each processor core and efficiently reduce power consumption is of vital importance, especially for real-time systems. In this paper, a novel scheduling algorithm is proposed for real-time multicore systems to balance the computation loads and save power. The developed algorithm simultaneously considers multiple criteria, a novel factor, and task deadline, and is called power and deadline-aware multicore scheduling (PDAMS. Experiment results show that the proposed algorithm can greatly reduce energy consumption by up to 54.2% and the deadline times missed, as compared to the other scheduling algorithms outlined in this paper.

Simulating Real-Time Aspects of Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Christian Nastasi

2010-01-01

Full Text Available Wireless Sensor Networks (WSNs technology has been mainly used in the applications with low-frequency sampling and little computational complexity. Recently, new classes of WSN-based applications with different characteristics are being considered, including process control, industrial automation and visual surveillance. Such new applications usually involve relatively heavy computations and also present real-time requirements as bounded end-to- end delay and guaranteed Quality of Service. It becomes then necessary to employ proper resource management policies, not only for communication resources but also jointly for computing resources, in the design and development of such WSN-based applications. In this context, simulation can play a critical role, together with analytical models, for validating a system design against the parameters of Quality of Service demanded for. In this paper, we present RTNS, a publicly available free simulation tool which includes Operating System aspects in wireless distributed applications. RTNS extends the well-known NS-2 simulator with models of the CPU, the Real-Time Operating System and the application tasks, to take into account delays due to the computation in addition to the communication. We demonstrate the benefits of RTNS by presenting our simulation study for a complex WSN-based multi-view vision system for real-time event detection.

Software Design Methods for Real-Time Systems

Science.gov (United States)

1989-12-01

This module describes the concepts and methods used in the software design of real time systems . It outlines the characteristics of real time systems , describes...the role of software design in real time system development, surveys and compares some software design methods for real - time systems , and

Real-time Pricing in Power Markets

DEFF Research Database (Denmark)

Boom, Anette; Schwenen, Sebastian

We examine welfare e ects of real-time pricing in electricity markets. Before stochastic energy demand is known, competitive retailers contract with nal consumers who exogenously do not have real-time meters. After demand is realized, two electricity generators compete in a uniform price auction...... to satisfy demand from retailers acting on behalf of subscribed customers and from consumers with real-time meters. Increasing the number of consumers on real-time pricing does not always increase welfare since risk-averse consumers dislike uncertain and high prices arising through market power...

Real-time Pricing in Power Markets

DEFF Research Database (Denmark)

Boom, Anette; Schwenen, Sebastian

We examine welfare eects of real-time pricing in electricity markets. Before stochastic energy demand is known, competitive retailers contract with nal consumers who exogenously do not have real-time meters. After demand is realized, two electricity generators compete in a uniform price auction...... to satisfy demand from retailers acting on behalf of subscribed customers and from consumers with real-time meters. Increasing the number of consumers on real-time pricing does not always increase welfare since risk-averse consumers dislike uncertain and high prices arising through market power...

Real-time objects development: Study and proposal for a parallel scheduling architecture

International Nuclear Information System (INIS)

Rioux, Laurent

1997-01-01

This thesis contributes to the programming and the execution control of real-time object oriented applications. Using real-time objects is very interesting for programming real- time applications, because this model can introduce the concurrence with the encapsulation properties, with modularity and reusability by taking into account the real-time constraints of the application. One essential quality of this approach is that it can directly specify the parallelism and the real-time constraints at the model level of the application. An annotation system of C++ has been defined to describe the real-time specifications in the model (or in the source code) of the application. It will supply to the execution support the different information it needs for the control. In this approach of multitasking, the control is distributed and encapsulated inside each real time object. Three complementary levels of control have been defined: the state level (defining the capability of an object to treat an operation), the concurrence level (assuring the coherence between the object attributes) and a scheduling control (allocating the processors resources to the object by taking real-time constraints into account). The proposed control architecture, named OROS, manages the attribute access of each object in an individual way, then it can parallel treatments which do not access at the same data. This architecture makes a dynamic control of an application that can take benefit from the parallelism of the new machines both for the execution parallelism and the control itself. This architecture uses only the simplest primitives of the industrial real-time operating systems which ensures its feasibility and portability. (author) [fr

Research of real-time communication software

Science.gov (United States)

Li, Maotang; Guo, Jingbo; Liu, Yuzhong; Li, Jiahong

2003-11-01

Real-time communication has been playing an increasingly important role in our work, life and ocean monitor. With the rapid progress of computer and communication technique as well as the miniaturization of communication system, it is needed to develop the adaptable and reliable real-time communication software in the ocean monitor system. This paper involves the real-time communication software research based on the point-to-point satellite intercommunication system. The object-oriented design method is adopted, which can transmit and receive video data and audio data as well as engineering data by satellite channel. In the real-time communication software, some software modules are developed, which can realize the point-to-point satellite intercommunication in the ocean monitor system. There are three advantages for the real-time communication software. One is that the real-time communication software increases the reliability of the point-to-point satellite intercommunication system working. Second is that some optional parameters are intercalated, which greatly increases the flexibility of the system working. Third is that some hardware is substituted by the real-time communication software, which not only decrease the expense of the system and promotes the miniaturization of communication system, but also aggrandizes the agility of the system.

Real-Time Load-Side Control of Electric Power Systems

Science.gov (United States)

Zhao, Changhong

Two trends are emerging from modern electric power systems: the growth of renewable (e.g., solar and wind) generation, and the integration of information technologies and advanced power electronics. The former introduces large, rapid, and random fluctuations in power supply, demand, frequency, and voltage, which become a major challenge for real-time operation of power systems. The latter creates a tremendous number of controllable intelligent endpoints such as smart buildings and appliances, electric vehicles, energy storage devices, and power electronic devices that can sense, compute, communicate, and actuate. Most of these endpoints are distributed on the load side of power systems, in contrast to traditional control resources such as centralized bulk generators. This thesis focuses on controlling power systems in real time, using these load side resources. Specifically, it studies two problems. (1) Distributed load-side frequency control: We establish a mathematical framework to design distributed frequency control algorithms for flexible electric loads. In this framework, we formulate a category of optimization problems, called optimal load control (OLC), to incorporate the goals of frequency control, such as balancing power supply and demand, restoring frequency to its nominal value, restoring inter-area power flows, etc., in a way that minimizes total disutility for the loads to participate in frequency control by deviating from their nominal power usage. By exploiting distributed algorithms to solve OLC and analyzing convergence of these algorithms, we design distributed load-side controllers and prove stability of closed-loop power systems governed by these controllers. This general framework is adapted and applied to different types of power systems described by different models, or to achieve different levels of control goals under different operation scenarios. We first consider a dynamically coherent power system which can be equivalently modeled with

The Alzheimer's Disease Assessment Scale-Cognitive-Plus (ADAS-Cog-Plus): an expansion of the ADAS-Cog to improve responsiveness in MCI.

Science.gov (United States)

Skinner, Jeannine; Carvalho, Janessa O; Potter, Guy G; Thames, April; Zelinski, Elizabeth; Crane, Paul K; Gibbons, Laura E

2012-12-01

The Alzheimer's Disease Assessment Scale cognitive subscale (ADAS-Cog) is widely used in AD, but may be less responsive to change when used in people with mild cognitive impairment (MCI). Participants from the Alzheimer's Disease Neuroimaging Initiative were administered a neuropsychological battery and 1.5 T MRI scans over 2-3 years. Informants were queried regarding functional impairments. Some participants had lumbar punctures to obtain cerebrospinal fluid (CSF). We added executive functioning (EF) and functional ability (FA) items to the ADAS-Cog to generate candidate augmented measures. We calibrated these candidates using baseline data (n = 811) and selected the best candidate that added EF items alone and that added EF and FA items. We selected candidates based on their responsiveness over three years in a training sample of participants with MCI (n = 160). We compared traditional ADAS-Cog scores with the two candidates based on their responsiveness in a validation sample of participants with MCI (n = 234), ability to predict conversion to dementia (n = 394), strength of association with baseline MRI (n = 394) and CSF biomarkers (n = 193). The selected EF candidate added category fluency (ADAS Plus EF), and the selected EF and FA candidate added category fluency, Digit Symbol, Trail Making, and five items from the Functional Assessment Questionnaire (ADAS Plus EF&FA). The ADAS Plus EF& FA performed as well as or better than traditional ADAS-Cog scores. Adding EF and FA items to the ADAS-Cog may improve responsiveness among people with MCI without impairing validity.

Variable slip wind generator modeling for real-time simulation

Energy Technology Data Exchange (ETDEWEB)

Gagnon, R.; Brochu, J.; Turmel, G. [Hydro-Quebec, Varennes, PQ (Canada). IREQ

2006-07-01

A model of a wind turbine using a variable slip wound-rotor induction machine was presented. The model was created as part of a library of generic wind generator models intended for wind integration studies. The stator winding of the wind generator was connected directly to the grid and the rotor was driven by the turbine through a drive train. The variable resistors was synthesized by an external resistor in parallel with a diode rectifier. A forced-commutated power electronic device (IGBT) was connected to the wound rotor by slip rings and brushes. Simulations were conducted in a Matlab/Simulink environment using SimPowerSystems blocks to model power systems elements and Simulink blocks to model the turbine, control system and drive train. Detailed descriptions of the turbine, the drive train and the control system were provided. The model's implementation in the simulator was also described. A case study demonstrating the real-time simulation of a wind generator connected at the distribution level of a power system was presented. Results of the case study were then compared with results obtained from the SimPowerSystems off-line simulation. Results showed good agreement between the waveforms, demonstrating the conformity of the real-time and the off-line simulations. The capability of Hypersim for real-time simulation of wind turbines with power electronic converters in a distribution network was demonstrated. It was concluded that hardware-in-the-loop (HIL) simulation of wind turbine controllers for wind integration studies in power systems is now feasible. 5 refs., 1 tab., 6 figs.

Database application research in real-time data access of accelerator control system

International Nuclear Information System (INIS)

Chen Guanghua; Chen Jianfeng; Wan Tianmin

2012-01-01

The control system of Shanghai Synchrotron Radiation Facility (SSRF) is a large-scale distributed real-time control system, It involves many types and large amounts of real-time data access during the operating. Database system has wide application prospects in the large-scale accelerator control system. It is the future development direction of the accelerator control system, to replace the differently dedicated data structures with the mature standardized database system. This article discusses the application feasibility of database system in accelerators based on the database interface technology, real-time data access testing, and system optimization research and to establish the foundation of the wide scale application of database system in the SSRF accelerator control system. Based on the database interface technology, real-time data access testing and system optimization research, this article will introduce the application feasibility of database system in accelerators, and lay the foundation of database system application in the SSRF accelerator control system. (authors)

Distributed digital real-time control system for the TCV tokamak and its applications

NARCIS (Netherlands)

Anand, H.; Galperti, C.; Coda, S.; Duval, B.P.; Felici, F.; Blanken, T.; Maljaars, E.; Moret, J.M.; Sauter, O.; Goodman, T.P.; Kim, D.

2017-01-01

A key feature of the new digital plasma control system installed on the TCV (Tokamak à Configuration Variable) tokamak is its possibility to rapidly design, test and deploy real-time algorithms. It accommodates hundreds of diagnostic inputs and actuator outputs, and offers the possibility to design